Escolar Documentos
Profissional Documentos
Cultura Documentos
Materiales:
Hilos, cuentas, fornituras , herramientas: alicates.
EL HILO: de lino, de nylon, elstico, de cobre, de latn, de acero, de silicona,
de polyester...
Alambre
Poliester
Nylon
A ste hilo de nylon tambin se le llama de pescar pues es el que utilizan los
pescadores. Le hay en diferentes colores, grosores y tamaos de carrete,
cuanto mas grande sea el carrete ms barato le saldr el metro de nylon.
Se pueden hacer multitud de cosas con l, como: collares, pendientes, anillos...
Se puede comprar en tiendas de pesca en vez de en merceras ya que saldr
ms barato.
Elstico
CADENA
CAUCHO
GAMUZA
CUERO
SEDA
CUENTAS
Cristal y madera
FORNITURAS
las chafas: que sirven para hacer de tope para rematar o sostener una perla
en un determinado lugar del hilo (tambin se les denominan grapas)
HERRAMIENTAS
Alicates, tijeras, pegamento
ALICATES
CONSEJOS Y TRUCOS
Para realizar cosas con abalorios se necesita de paciencia y ser meticuloso por
ello, se recomienda clasificar las perlas por tamaos y colores.
Haciendo una bola de retencion evitamos que se salgan los abalorios que
vamos metiendo
Para que el trabajo no se afloje se puede poner en un nudo una pequea gota
de cola a poder ser transparente.
Para una terminacin mas limpia en vez de hacer un nudo se pasa por el
broche y y se repasa el ultimo abalorio en sentido contrario
TCNICAS
TCNICAS BSICAS:
enfilado simple
enfilado cruzado
enfilado multiple
las flores
Los tringulos
Los circulos
El telar
enfilado simple
Se usan dos cabos del mismo hilo para ir cruzandolos en los abalorios
centrales. Se recomienda tomar un hilo largo (no hay que excederse ya que si
lo tomamos uno muy grande es mas trabajoso pq hay que pasar las bolas por
todo el hilo) y se comienza centrando los abalorios iniciales en el hilo tomado.
Esta es la tcnica que se usa para los animales; slo difiere en la colocacin
final que se de a las filas que hemos obtenido, en los animales planos las filas
van seguidas y planas y en los animales en 3d las filas se montan unas sobre
otras formando como un acorden.
Aqui vers una explicacin mas detallada:
Paso 2: enfila lo que va a ser la segunda fila, en este caso otros 3 abalorios,
con uno de los extremos del hilo
Paso 3: Pasa el otro extremo del hilo por los 3 abalorios de esa segunda fila
haciendo que se crucen ambos extremos
Paso 4: tira de ambos extremos para que se ajuste el hilo y vuelve a empezar
(mete la siguiente fila pasando por un extremo los abalorios de los que conste
la fila y repsalos con el otro extremo del hilo)
MULTIPLE ENROLLADO
MULTIPLE TRENZADO
Se trata de varios enfilados simples que se unen en el broche, se usa un
capuchn para recoger todos los hilos o una cuchilla (lo que se muestra en el
esquema con varios terminales)
El enfilado mltiple y el enfilado multiple enrollado se diferencian en que el
mltiple enrollado antes de ponertelo lo retuerces sobre si mismo hasta lograr
el enrolle deseado
El enfilado mltiple trenzado se trenza antes de poner el broche
las flores
SIMPLE
los tringulos
los crculos
Se usan dos cabos del mismo hilo para ir cruzandolos en los abalorios
centrales. Se recomienda tomar un hilo largo (no hay que excederse ya que si
lo tomamos uno muy grande es mas trabajoso pq hay que pasar las bolas por
todo el hilo) y se comienza centrando los abalorios iniciales en el hilo tomado.
los cuadrados
bordado
Prepara una hebra de 50cm de largo y haz una bola de retencin a 10cm del
extremo. Pasa el hilo por la bola que vamos a forrar de abajo a arriba y
sacamos el hilo por arriba. Enfilamos 6 abalorios y pasamos de nuevo el hilo de
abajo a arriba y repetimos esto hasta forrarlo. (las medidas dependern del
tamao de los abalorios con los que trabajeis)
Cuando las bolas toquen el extremo enfila menos cantidad
Quita la perla de retencin y ata los 2 extremos
LAS PUNTADAS:
Asi se realizan multitud de collares cuando veais un tejido asi ya sabreis como
hacerlo.
Es una puntada popular y verstil; una vez que aprendas la puntada del peyote
puedes aplicarla a muchos diseos.
1. Empieza la secuencia haciendo del abalorio 1 una bola de retencin, es
decir, pasa el hilo por l dos veces para anclarle y dejarle fijo.
2. Aade 7 abalorios ms. La base del ejemplo consta de 8 abalorios. En este
ejemplo se han usado 2 colores, el rosa y el azul y para que quede cada fila de
3. Una vez llegado al 8 aade el 9 del mismo color que ira en la fila siguiente,
pasa el hilo por el primer azul que te encuentras que es el 7, aade uno nuevo
rosa (10) vuelve por el siguiente azul (5) y as todo el rato hasta pasar por el
primer azul que metiste en el inicio donde se volveria a meter un abalorio azul
(13) para comenzar la fila siguiente. Aunque las explicaciones te resulten un
poco enrevesadas no tienes mas que mirar el dibujo que muestro en la parte
superior.
Continua de esta manera hasta que consigas el largo que desees
Ahora veremos como hacer para incrementar o disminuir el nmero de perlas
en las filas sucesivas
Para incrementar
Para reducir
Aconsejo hacer diseos sencillos hasta dominar la tcnica, escoge perlas que
sean uniformes tanto de tamao como de forma.
PEYOTE 2: simple, doble y triple
Siguiendo el esquema del peyote normal, en vez de usar una se usan 2 para el
peyote doble y 3 para el triple en cada puntada
PEYOTE TUBULAR
puntada
cuadrada
(square
stitch)
horizontal,
vertical
circular
Horizontal
Con esta puntada, coses los abalorios uno a uno. Tiene el mismo resultado que
el tejido realizado con el telar pero esta forma de realizarlo es mas trabajosa.
Podeis realizar vuestros propios diseos coloreando una hoja cuadriculada.
FORMA DE REALIZARLA
1. Enhebra tu aguja y psala a travs del abalorio 1 haciendo una bola de
retencin
2. Enfila otros cinco abalorios para formar la primera fila q constar de seis
abalorios
3. Mete el abalorio 7 y alinalo con el 6 ponindolo justo encima.
Pasa el hilo a travs del abalorio 6 y vulvelo a pasar por el abalorio 7
1. Encadena 4 abalorios y pasa el hilo otra vez por los cuatro en la misma
direccin.
Colocales en 2 filas de 2 abalorois cada una.
Una vez realizado este comienzo se trabaja igual que en la puntada cuadrada
simple, aade 2 abalorios, pasa el hilo por los 2 anteriores y vuelvelo a pasar
por los 2 nuevos.
Circular
Filas de 1 a 5
1. Mete 6 abalorios y forma un crculo atando un nudo
2. Empieza en el punto verde del dibujo que es el nudo. Mete el hilo por el
primero anterior y aade 2 nuevas, pasale por el mismo de la fila anterior. Mete
el hilo por el siguiente de la fila anterior, aade 3 nuevas y pasale por el mismo
de la fila anterior, as repite hasta que hayas aadido 15, siempre con la
secuencia de 2 en 1, 3 en el 1 siguiente y por ultimo repeticin alrededor (15
nuevas)
3. 2 en 1, 1 en cada 2 siguientes, repeticin alrededor (20 nuevas)
4. 2 en 1, 1 en cada 2 siguientes, repeticin alrededor, extremo con 2 en 1
entonces 1 en 1 (27 nuevas)
5. 2 en 1, 1 en cada 2 siguientes, repeticin alrededor (36 nuevas)
Filas 6 a 10
1. 2 en 1, 1 en cada 3 siguientes, repeticin alrededor (45 nuevas)
2. 2 en 1, 1 en cada 3 siguientes, repeticin alrededor, extremo con 2 en 1
(57 nuevas)
3. 2 en 1, 1 en cada 5 siguientes, repeticin alrededor, extremo con 2 en 1
entonces 1 en cada 2 siguientes (67nuevas)
4. 2 en 1, 1 en cada 7 siguientes, repeticin alrededor, extremo con 2 en 1
entonces 1 en cada 2 siguientes (76nuevas)
5. 2 en 1, 1 en cada 9 siguientes, repeticin alrededor, extremo con 2 en 1
entonces 1 en cada 5 siguientes (84nuevas)
Foto de http://www.beadwrangler.com/samplers/sampler-current.htm
sta es una tcnica donde los abalorios quedan colcados como ladrillos
puesto que los abalorios de las filas superiores no corresponden con los
abalorios de las filas inferiores sino entre ellos.
Los diseos se trabajan en filas horizontales y la anchura puede
aumentarse o disminuirse a tu gusto
FILA BASE
Coloca un abalorio en el centro del hilo y ve aadiendo un abalorio y
cruzando los 2 cabos en cada uno. Asi formars la fila base. El hilo inferior
se desechar y trabajamos con el superior.
PARA FILAS CON EL MISMO N DE ABALORIOS
Aade 2 abalorios y pasa el hilo entre los hilos de los abalorios de la fila
inferior
Se hace un recorrido por los 2 abalorios del extremo para fijarles. Sigue el
orden del esquema
Comanche simple
Comanche doble
Mete 4 abalorios
Coloca el extremo del hilo hacia arriba para que se coloquen esta nueva
pareja de abalorios y pasa el hilo por la pareja anterior, despues vuelvelo a
pasar por la ultima pareja de abalorios que aadiste
Sigue as hasta realizar la primera fila
Las filas 1 a 7 son filas del aumento, las filas 8 a 13 son filas de
disminucin. Comienza el diamante con 2 abalorios.
MUESTRA DOBLE
Se trabaja de 2 en 2
Se comienza con 4 abalorios y se tensa
Este ejemplo consta de 21 filas
La fila ms ancha tiene 12 abalorios
Muestras con variaciones de la puntada comanche
2. Mete 3 abalorios mas (#5, #6, y #7) . Reentra por #3, #5 y #6. La direccin
de giro es al contrario de las agujas del reloj
6. Mete otros 2 abalorios (#17 y #18) y reentra por #8, #14, #17 y #18.
Sigue asi aadiendo 2 nuevos y reentrando por los anteriores, en una puntada
se sigue la direccin de las agujas del reloj y en la siguiente se realiza en
sentido contrario
Solo hay que ir haciendo esa rutina hasta que consigamos el largo deseado
para nuestra pulsera o gargantilla.
los remates
REMATE COMUN
Pasa el hilo por el cierre y vuelve pasandolo por la ultima perla que hayas
puesto. Entonces en ese punto haces un nudo. Ese nudo puedes fijarlo con
una gota pegamento
REMATE NATURAL
En un extremo haces un arito de abalorios y en el otro colocas una bola
gorda
las anillas
Para comenzar a formar la anilla, tuerce suavemente los alicates hacia afuera
(no para ti).
Aprieta los alicates al alambre de modo que no se muevan y haz un medio giro
de modo que coja la forma de anilla, ya que tanto tu mano como tu mueca
alcanzan una posicion poco util vuelve a colocar los alicates de manera que
fijen el alambre y sigue dandole la media vuelta hasta conseguir la anilla
deseada
Contina con el paso anterior, hasta que se forme la anilla. Al rotar los alicates,
estate seguro que toda la anilla tiene contacto completo con los alicates. Esto
asegurar que la forma de la anilla sea uniforme
Sugerencia:
Dibuja una marca en tus alicates con un rotulador permanente. Utiliza esta
marca como gua para colocar el alambre al hacer la anilla. As sabrs
exactamente dnde agarrar el alambre para que te salgan las anillas lazos
perfectos
Fotos tomadas de http://www.beadaroo.com/techniques/basics.php
Eva RD nos explica como lo hace:
Coloca el alambre en los alicates La parte de abajo del alambre debe estar
rasante con los alicates
Sosten los alicates en tu mano dominante con el extremo del alambre hacia ti.
La mano que agarra la parte inferior del alambre debe quedar mas lejos que la
mano que coge los alicates
Dobla el extremo del alambre hacia afuera (no hacia ti) para que quede
alrededor de los alicates con el pulgar de tu mano no dominante (izquierda si
eres diestro, derecha si eres zurdo). Sigue doblando el alambre alrededor del
alicate pero no necesitas doblarlo del todo
Empuja el extremo superior del alambre que esta tomando forma de anilla
hacia abajo alrededor de los alicates hasta formar una anilla completa
Si ahora miras tu anilla, notars que no est centrada. Agarra la parte inferior
del alambre y ajusta el lazo a esta parte rotando el lazo sobre l
Quite la anilla de los alicates redondos y agarra la anilla con un alicate plano
con tu mano no dominante. Agarra el otro extremo con otro alicate con tu mano
dominante
El alicate que tiene la anilla no se mueve. Rota el otro alicate hacia afuera
rodeando la base de la anilla. Esto formar el primer lazo alrededor de la base
del alambre, as que intenta enrollarlo cerca de la anilla
Despus de dar esa media vuelta alrededor de la base y tener el extremo
mirando hacia abajo, coge de nuevo el extremo y dirgelo hacia arriba
Sigue asi en pasos de media vuelta. (media vuelta hacia arriba, cambias
posicin de los alicates y media vuelta hacia abajo)
Tres lazos de esta manera es lo ms usual, aunque puedes realizar ms o
menos segn el proyecto que ests realizando.
Para abrir una anilla, utiliza 1 par de alicates para agarrar las aberturas del
alambre. Tira de los alicates uno hacia ti y otro empujale hacia el lado contrario
Nunca separes las anillas hacia fuera ya que fatigar el metal
Cierra la anilla tirando de los extremos de manera contraria
Bastones caseros
TCNICA 1
Utiliza un alambre de 25 centmetros
8. Ahora coge el extremo de alambre ms largo y coloca los abalorios que sean
necesarios para alcanzar el segundo abalorio de la parte superior
Inserta el alambre a travs de este grano
Repite el paso 7 (mete igual cantidad de abalorios, conduce el alambre hasta
abajo y nelo con el otro extremo aadiendo un abalorio)
REDONDO
Cuando comiences el ptalo mete en el nuevo alambre con el que
trabajaremos un nmero determinado de abalorios de tal manera que quede
paralelo a los abalorios que hemos metido previamente en el alambre base
ACENTUADO
La base es la misma que en el anterior ptalo, mete en el nuevo alambre un
numero determinado de abalorios de tal manera que quede paralelo a los
abalorios que hemos metido previamente en el alambre base
Aadiremos 2 ms (dibujo 1) para darle esa determinada forma
EN LAZO
Meteremos en un extremo los abalorios necesarios para realizar un primer lazo,
enrollamos el extremo en la parte inferior
Realizamos un nuevo lazo y volvemos a enrollar el extremo en la parte inferior
y realizamos otro lazo
Por ltimo enrollamos los extremos
EN CRUZ
Realiza un lazo y enrolla un extremo en la parte inferior
Vuelve a subir un extremo enfilandole los abalorios que sean necesarios y
tuerce el alambre dandole una vuelta sobre el alambre del primer lazo en su
parte superior (dibujo 1)
Luego dirgele a la parte inferior enrollando los extremos entre s
ABRIGO
Se realiza haciendo sucesivos lazos
Mete los abalorios necesarios para el primer lazo y enrolla el extremo en la
parte inferior del otro extremo que le hemos dejado como base dndole 2
vueltas. Realiza otro lazo y colcale lo mas junto que puedas al primero, vuelve
a enrollar el extremo en la parte inferior (en el alambre base)dandole 2 vueltas.
Sigue asi hasta conseguir el ptalo que deseas
AISLADOS
Mete los abalorios que sean necesarios por un extremo, ese extremo volver
sobre los mismos abalorios en sentido contrario excepto por el primero
Tuerce el extremo en la parte inferior sobre el otro extremo
Estas
tcnicas
estan
sacadas
de
la
web
http://beadedflowers.tripod.com/international/index.htm
los nudos
El nudo simple
El nudo doble o cuadrado
El Nudo De los Cirujanos
Nudo mltiple
Se va girando el cabo hacia abajo para luego subir por el interior de las vueltas
dadas
La Figura-ocho
Con el cabo se hace como un ocho que baja y acaba metiendose por el interior
de la primera vuelta
El nudo de la alondra
Se usa tambie para comenzar macrame pero con un solo cabo. Se hacen
medios nudos pero es doble pq cada uno consta de 2 medios nudos
La CURVA de Carrick
El NUDO Delantero-detra's-delantero
usamos un telar
Con el telar podremos realizar collares, pulseras, cinturones, cuadros, y todo
aquello que se te ocurra.
1 tablilla de 30x10cm
18 clavos cobrizados
2 listones de madera
6 hembrillas
6 tornillos
1 martillo
regla
lapiz
La tablilla sera de 30x10 para hacer pulseras y de 55x10 para hacer collares
En la foto muestro otro tipo de clavos que tambien pueden utilizarse, buscalos
con cabeza pequea
Los listones seran de 10cm de longitud, 1cm de grosor y 1,5 de altura
(aproximadamente)
MI TELAR
1. BASE
Consta de 3 hembrillas que sirven para tensar los hilos que forman el telar. En
el otro extremo tambien pondremos otras 3
Colocamos la central en el centro (a 5 cm de las esquinas)
2. PRIMER TOPE
A 8 cm del extremo de la tabla haremos una linea a lo ancho con el lapiz para
marcar donde irn los clavos. Sobre la linea colocaremos los clavos con una
separacin corta (que te quepa otro clavo entre 2). Despues de los clavos
pondremos el liston a lo ancho ancho de nuestra tabla el cual sujetaremos con
3 tornillos (tambin podemos usar clavos)
He usado clavos de cobre porque tienen poca cabeza y asi cuando se acaba el
proyecto es ms fcil sacarlo
3. SEGUNDO TOPE
Al igual que el primer tope consta de los clavos colocados a 8cm del extremo y
a continuacion el liston a lo ancho de la tabla. En esta foto se puede apreciar
mejor como los tornillos sujetan el liston en la tabla
Telar indio americano realizado en metal, de uso sencillo, es ideal para los
aficionados. Las medidas de trabajo son 7 x 31 cms. Vale unos 10
Telar para brazaletes Aleene, para realizar pequeos modelos. Vale unos 25
3 de los telares que se pueden comprar en merceras
Este es mi telar casero si quieres saber como esta hecho pincha sobre el
Lo primero de todo es elegir el modelo que quieras hacer. Puedes escoger uno
de las 6 galerias que tienes a tu disposicin al final de esta pgina o hacer uno
tu mismo/a en una hoja cuadriculada
Una vez q tienes el modelo, cuenta los abalorios del ancho del diseo y smale
uno, el resultado es el nmero de hilos que debes colocar en el telar.
Fija los hilos en el extremo del telar y tnsalos bien
Para comenzar ata el hilo con el que vas a trabajar en el primer hilo de la
urdimbre (el primero de la izquierda)
Coloca los abalorios entre los hilos con el dedo indice o corazon y empujales
hacia arriba
Ayudandonos con el dedo que sostiene los abalorios pasamos el hilo por
encima de la urdimbre de derecha a izquierda
Para terminar ata un nudo con el hilo que trabajas al hilo de la urdimbre y corta
los hilos de la urdimbre. Haz una trenza y ya esta lista la pulsera
Ahora pasa el hilo por dichos abalorios pero por encima de los hilos del telar
En el segundo dibujo se aprecia que primero se pasa por debajo de izquierda
a derecha y despues se pasar por encima de derecha a izquierda
FINAL EN DISMINUCION
FINAL RECTO
3. ACABADO CON VELCRO idea aportada y explicada por Beln
Cortar dos trozos del cuero o skay, del ancho de la pulsera y coserle en cada
extremo un trozo de velcro, para que al finalizar la pulsera sea de fcil uso.
Con la ayuda de una aguja pasar los hilos de nylon a travs de la tela para que
luego no se vean
Esquema tejido1
1
OOO
2
X X X
3
X X X
4
5
X X
6
X X
7
X X
8
X X X
9
X X X
10
OOO
OOOO
X X X X
X X X X
X X
X X
X X
OOOOO
X X X X X
X X X X X
X X
X X
X X
X X
X X
X X
X X X X X X X X X
X X X X X X X X X
OOOOOOOOO
OOOOOOO
X X X X X X X
X X X X X X X
X X
X X
X X
X X
X X
X X
X X X X X X X
X X X X X X X
OOOOOOO
OOOOO
X X X X X
X X X X X
X X
X X
X X
X X
X X
X X
X X X X X
X X X X X
OOOOO
OO
X X
X X
X
X
X
X X
X X
OO
Esquema tejido 2
1
O OO O O
2
X
X
3
X
X
4
X
5
X
X
6
X
X
7
X
X
8
X
9
X
X
10
X
X
11
X
X
12
X
13
O OO O O
Esquema tejido3
1
Z Z Z
2
3
Z Z Z
4
Z
5
Z
6
Z
7
Z Z
8
Z
9
Z
10
Z
11
Z Z Z
12
13
Z Z Z
O O O O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O O O O
O O O O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O O O O
O O O O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O O O O
Z Z Z Z Z Z Z Z Z Z Z Z
Z
Z Z Z Z Z Z Z Z
Z Z
Z
Z Z
Z
Z Z
Z
Z
Z Z
Z
Z
Z Z
Z
Z
Z
Z Z
Z
Z Z
Z
Z Z
Z Z Z Z Z Z Z Z
Z Z
Z
Z Z Z Z Z Z Z Z Z Z Z Z
O O O O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O O O O
Z Z Z Z Z
Z
Z Z
Z Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z Z
Z
Z Z
Z Z Z Z Z
O O O O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O O O O
Z Z Z Z Z Z
Z
Z Z
Z
Z
Z Z
Z
Z Z Z
Z
Z
Z
Z Z
Z
Z
Z
Z Z Z
Z
Z
Z Z Z Z Z Z
Esquema tejido4
1
ZZZZZZZZZZZZZZZZZZZZZZZZZZZZZ
2
O
O
O
O
3
OO
OOO
OOO
O OO
4
OOO
OOOOO
OOOOO
O O OOO
5
O O O O O O O O O O O O O O O O O O O O O OOO O
6
O O O O O O O O O O O O O O O O O O OO O
7
OOOO
OOOO
OOOO
OO
8
OOOO
OOOO
OOOO
OOO
9
O O O O O O O O O O O O O O O O O O OO O O
10
11
12
13
14
O O O O O O O O O O O O O O O O O O O O O OOO O
OOO
OOOOO
OOOOO
O O OOO
OO
OOO
OOO
O OO
O
O
O
O
ZZZZZZZZZZZZZZZZZZZZZZZZZZZZZ
Esquema tejido 5
1
Z Z Z Z Z Z Z Z Z Z Z
2
O O O O Z R R R R R R
3
O
O Z R
R
4
O
O Z R R
5
O O O Z R R R R R R R
6
O O Z
8
O O Z
9
O O Z
10
O O O Z B B B B B B B
11
O
O Z B B
12
O
O Z B
B
13
O O O O Z B B B B B B
14
Z Z Z Z Z Z Z Z Z Z Z
Z=negro, O=naranja, B=azul, R=rojo
Pulseras africanas
Z
Z
Z
R
R
Z
O
O
Z
Z
B
B
Z
Z
Z
Z
Z
O
O
Z
Z Z Z Z Z Z Z
O O O O O O Z
O Z
O
O Z R
O O
O O Z R
Z O
O Z
Z O
O Z
Z O
O Z
O O
O O Z B
O
O Z B
O Z
O O O O O O Z
Z Z Z Z Z Z Z
Z Z Z Z Z Z Z Z
R R R R R RZ O
R
RZ O
R
RZ
R R R R R RRZ
B B B B B BBZ
B
BZ
B
BZ O
B B B B B BZ O
Z Z Z Z Z Z Z Z
wigjig:
usamos el wigjig para dar forma al alambre
WigJig Original
La plantilla tiene 4 clavijas
Mini-Athena WigJig
Es una plantilla del metal con 9 clavijas. Adecuado para hacer nudos clticos y
egipcios. Puedes hacer diseos que con otro wigjig no podrias
Proyecto
WigJig Electra
Tiene una forma circular que facilita hacer diseos con curvas y circulos,
puedes hacer diseos que no podras realizar con otros wigjig. Tiene el mismo
tamao de las clavijas como el Olympus y el Olympus-Lite
WigJig Cyclops
Tambien es una plantilla circular que facilita hacer diseos con curvas y
circulos los cuales no se pueden hacer con otro wigjig
Para electra y cyclops detalles
2Tier Earrings
Jewelry Making Skills Required:
The three wire components used to make the body of these earrings are shown at
right. We also need a modified figure 8 connector and an ear wire finding to
complete these earrings. Our instructions for making this jewelry item begin with
the top wire component. On page 3 we will provide the instructions for the 3 loop
wire component and for how to connect the 3 loop component to the top wire
component. On page 4 we provide instructions for the 5 loop wire component and
on page 6 we provide instructions for assembling the earrings including the modified
figure
8
connector
and
the
ear
wire
finding.
Step 1: Cut and make a loop in one end of a piece of 20 gauge wire 2 inches long.
1/2 hard wire is preferred.
Step 2: Straighten this wire.
Step 3: Place pegs 1 and 2 into your WigJig Cyclops or Centaur as shown at right.
Put the initial loop on peg 1 and wrap the wire around peg 2 1-3/4 times so that it
rests
against
the
hole
where
peg
3
would
go.
Step 4: Now add peg 3 and wrap the wire around this peg.
Step 5: Remove the wire from the jig and cut the excess wire. Close the loop made around peg 3 with
your bent chain nose pliers.
Step 6: Now using your round nose pliers convert both loops in the top wire component into "eye" loops
as shown at the bottom here.
Step 7: Using your bent chain nose pliers, one at a time grasp the loops at the bottom of this wire
component and twist them 90 degrees. When completed it should appear as shown below, right.
Step 5
Step 6
Step 7
Step 8: Cut and make a loop in one end of a piece of 20 gauge wire 1-1/2 inches long.
Step 9: Straighten this wire using your nylon jaw pliers.
Step 10: Position pegs 1 and 2 in your jig as shown at right. Place the initial loop on
peg 1 and wrap the wire around peg 2 so that it rests against the hole for peg 3.
Step 11: Now add peg 3 and wrap the wire around this peg.
Step 12: Remove the wire from the jig and cut the excess wire. Now using your bent
chain
nose
pliers,
close
the
loop
made
on
peg
3.
Step 13: Now we need to connect the top wire component to the 3 Loop wire
component. First open one of the bottom loops in the Top Wire Component using your
bent chain nose pliers and insert the corresponding loop from the 3 Loop wire
component. Then on the opposite side, open both the loop in the Top Wire Component
and the loop in the 3 Loop wire component and connect these two loops. Once the wire
is in position, close both loops. At this point the two wire components should appear as
shown at right.
At this point, we have the Top Wire Component connected to the 3 Loop
Wire component and we need to assemble the remainder of the earring
body.
Step 21: Using a 1-1/2 inch head pin and a 4mm bead, thread the bead onto
the head pin and make a bead dangle hanging from the middle loop in the 3
Loop Wire Component. Instructions for making a bead dangle can be found
here.
Step 22: Now we need to connect the 3 Loop Wire Component to the 5 Loop Wire
component using the wrapped bead link, first on one side, then on the other. Use 22
gauge wire for making the wrapped bead link, with 4mm beads. 1/2 hard wire is best
if available. Instructions for making this wrapped bead link can be found here.
Connecting the first wrapped bead link will be relatively easy. Connecting the
second, on the opposite end, will require that you open the loop on that end of the 5
Loop Wire Component with your bent chain nose pliers, then connect the loop in
your wrapped bead link and then close the loop in the 5 Loop Wire Component.
Step 23: Once the 3 Loop and 5 Loop Wire Components are connected, then with 5
head pins and 5 4mm beads, hang a bead dangle from each of the loops in the 5
Loop Wire Component, just like you did in Step 21.
Step 24: Now we need to make the modified figure 8 connector using 1 1/4" of 20
gauge wire. Instructions for making this component can be found here. Once
completed, open one loop in the modified figure 8 connector and connect it to the top
loop in the Top Wire Component.
Step 25: Open the remaining loop in the modified figure 8 connector and connect it
to your commercial ear wire finding. This completes your 2 Tier Earrings.
In the following web page, we will provide the pattern for these earrings using our
WigJig Delphi, Olympus or Olympus-Lite jigs.
The pattern for making these earrings on the WigJig Delphi is shown at right. This
same pattern will apply to the Olympus or Olympus Lite, only the resulting earrings
will be larger. The steps for making these earrings are exactly the same as we have
described previously.
The finished earrings made on the Delphi can be viewed at right. These earrings
are slightly different than the earrings made using the round pattern of the WigJig
Cyclops, Electra or Centaur.
The obvious question is if two is good, would three be better? In the case of
these earrings the answer is maybe. You can easily add a third tier to these
earrings by adding a new wire component. This new wire component is a five
loop component, but is made on a different radius of the WigJig Centaur,
Cyclops or Electra. The pattern for this Third Tier Wire Component is shown
below, right. This component is made using the same steps that we used to
make the 5 Loop Wire Component for the two tier earrings, but requires 3-1/4"
of 20 gauge wire, preferable 1/2 hard. (This 3 Tier Design does not easily work
for a jig with a square peg pattern like the WigJig Delphi or Olympus.)
Making these earrings is exactly the same as making the two tier earrings
except that you connect three bead dangles to the 5 Loop Wire Component in
Step 23, then you use 22 gauge wire and wrapped bead links to connect the 5
Loop Wire Component to the Third Tier Wire Component. The techniques for
connecting these two wire components are exactly the same as were used to
connect the 3 Loop Wire Component to the 5 Loop Wire component described
in Step 22. Obviously, the 3 Tier Earrings require 10 additional 4mm beads and
head pins and more 20 gauge and 22 gauge wire.
When you are ready for special earrings that will really get noticed, consider
Materials used:
The materials used in making these earrings in gold-filled wire are as follows:
The Materials used in making these earrings in Sterling Silver wire are as follows:
20 Gauge anti-tarnish sterling silver 1/2 hard round wire (Item 3005)
22 Gauge anti-tarnish sterling silver 1/2 hard round wire (Item 3007)
Sterling Silver head pins thin (Item 0082)
4mm Swarovski Bicone Beads or Round Beads or Pearl Beads
Sterling Silver Ear wire findings (Item 2659 or Item 0421)
In the prior several pages we made earrings that were shaped like an upside-down
letter "V", narrow at top and wide at the bottom. In these pages we will address a new
earring design, like the ones shown at right, that are shaped like the letter "V" in the
normal orientation, wide at top and narrow at the bottom. For this earring, the three
body wire components are exactly like the ones used to make our inverted "V" three
tier earrings. The peg patterns for making these three wire components are shown
below.
The one difference in the wire components for the earrings at right is the top wire
component. This modified design requires a different top wire component. In the
following web pages we show two approaches to making this top wire component.
Begin making these earrings by making the three wire components shown below.
Select any picture to navigate to our instructions for making that component. All three
components were made on the WigJig Cyclops, Centaur or Electra. These earrings
require about 18 inches of 20 gauge wire (preferably 1/2 hard) and 20 inches of 22
gauge wire (also preferably 1/2 hard). In the earrings at right 24 4mm beads and 4
6mm beads were used along with 22 head-pins and one pair of ear wire findings.
Large
Component
WireMiddle
Component
WireSmall
Component
Here we show two different styles for making the top wire components for these
earrings. For lack of a better name, we will call the left hand style, style 1 and the right
hand style, style 2. (Our imagination is on vacation today and we can't come up with a
better name.) Both of these styles work well. With style 1, a modified figure 8
connector is required to connect the middle loop in the wire component to your ear wire
finding. With style 2, the modified figure 8 connector is optional. You can connect
directly to your ear wire finding, or you can use the connector.
Step 1: The first step in making either style is to cut a piece of 20 gauge wire about 2
1/8" long and make a loop in one end of this piece of wire.
Style 2
Step 5: Remove the wire from your jig and using your flush
cutter, cut the excess wire.
Step 6: Using your bent chain nose pliers, close the loop in
the wire component made on peg 3.
Step 7: At this point, for either style of top wire component, we need to convert the
loops made on pegs 1 and 3 into eye loops and reorient them 90 degrees.
Converting these loops into eye loops is done by grabbing the wire with the tips of
your round nose pliers and twisting as shown at the bottom of this web page.
Eye Loops
Wire
Step 8: Reorienting the loops is done by grasping the loop with your bent chain
nose pliers while holding the loop made on peg 2 with your other hand, then
twisting your pliers 90 degrees. The end result will appear as shown at right. The
opening in the two loops can not been seen because it is facing to the side in a
plane that can not be viewed by the camera. This completes the top wire
Reoriented
component.
Step 9: Now we need to assemble the earrings. Connect the top wire component
to the largest of the three body wire components by opening the loops in both wire
components, making the connection then closing the loops.
Step 10: Using a 4mm bead and a head pin, make a bead dangle and hang the
bead dangle from the two outside loops and the center loop.
Step 11: Using 22 gauge wire and a 4mm bead, make two wrapped bead links to
connect the two empty loops on the largest wire component to the two outside
loops on the middle wire component. You will need to open the loops on the middle
wire component to help make this connection, then close the loops once the
connection has been made. At this point two of the tree tiers are connected.
Step 12: Just like you did in step 10, we need to use head pins and 4mm beads to
make bead dangles and hang these bead dangles on the two outside loops and the
center loop of the middle wire component.
These instructions continue on the next page.
Step 13: At this point we need to connect the third tier of the earrings. Using the
same approach that you did in step 11, use wrapped bead links to connect the loops
made on pegs 2 and 4 of the middle wire component to the outside loops in the small
wire component. This will require 22 gauge wire and 4mm beads.
Step 14: Using head pins and 4mm beads, connect bead dangles to the two outside
loops in the small wire component.
Step 15: Using a head pin and a 6mm bead, connect a bead dangle to the middle
loop in the small wire component. (As an alternative, you could use a 4mm bead
here.)
Step 16: Using a head pin and a 6mm bead, connect a bead dangle to the middle
loop in the top wire component. Because of the limited room available here, you may
not be able to use a wrapped loop here and may need to make an open loop bead
dangle as shown here.
Step 17: Now we need to make a modified figure 8 connector if we are using style 1
of the top wire component. Use about 1 1/4" of 20 gauge wire as described here.
Step 18: Once the modified figure 8 connector is completed, use it to connect the
middle loop in the top wire component to your ear wire finding. If you are using style
2 for the top wire component, you can connect the loop in the ear wire finding directly
to the middle loop in the top wire component.
Step 19: Use the same technique to make your second earring.
Alternatives:
The earrings shown at right are an alternative to the design we just completed.
These earrings use the top wire component from our 5 Plus 1 Beaded Chandelier
Earrings to make earrings that are really shoulder dusters. These earrings are long,
and may be too long for some folks. Instructions for making this 5 Plus 1 top wire
component can be found here. Other than this change, the process for making these
earrings is identical to the steps discussed in the prior pages.
In the following web pages we will show other alternative jewelry making designs for 2
tier and 3 tier "V" shaped beaded chandelier earrings.
Once you have these three wire components made, you assemble these earrings in
a manner that is similar to the technique discussed in pages 11 and 12, with one
exception. For these earrings the connections between the three tiers of wire
components (large to middle and middle to small) takes place between the outer
loops in each wire component.
For these earrings, because the small wire component is larger than the same
component in the earrings shown on page 9, you can use a larger bead dangle in the
middle of the small wire component. For these earrings, I used an 8mm bead here
instead of a 6mm bead.
In the following pages we will show some patterns for 2 tier "V" designs that can be
made on any WigJig jewelry making tool.
The earrings shown at right were made using the round peg pattern of the
WigJig Cyclops, Centaur or Electra. These earrings are made from four wire
components plus ear wire findings. The four wire components working down
from the ear wire finding are a modified figure 8 connector, the top wire
component, the 5 loop wire component and the three loop wire component.
Making these earrings requires 16 inches of 20 gauge wire (preferably 1/2
hard), 10 inches of 22 or 24 gauge wire (preferably 1/2 hard), 18 teardrop
beads, 14 1-1/2" head pins and a pair of ear wire findings.
For the earrings shown on the left, the modified figure 8 connector is optional.
For the earrings with the top wire component shown on the right, the modified
figure 8 connector is mandatory. Instructions for making this connector can
be
found
here.
The top wire connector connects the body of the earring to the modified figure
8 connector or optionally directly to the ear wire finding. This component is
made using the peg pattern shown at right. This top wire component for the
earrings on the left (shown above right) is made using the instructions for
"Style 2" from page 10 and 11. This component for the earrings on the right
was made using the instructions for "Style 1". With the Style 2 top wire
component, the modified figure 8 connector is optional. With Style 1, the
modified figure 8 connector is mandatory. As described in pages 10 and 11,Top
making this wire component uses 2 1/8" of 20 gauge wire and requiresStyle
wrapping the wire around the pegs as shown at right, cutting the excess wire,
converting the loops on pegs 1 and 3 to eye loops, and finally rotating those
loops 90 degrees.
Wire
Component
2
The next component to make is the 5 loop wire component. This component
is made with 3 1/4" of 20 gauge wire and the peg pattern shown at right. Start
by cutting your wire segment. Then make a loop in the end of the segment.
Grasp the loop and straighten the wire segment by pulling it through the jaws5 Loop Component
of your nylon jaw pliers. Now place pegs 1 and 2 in your jig, as shown at
right, and place the initial loop on peg 1. Wrap the wire around peg 2 until the
wire tail is adjacent to the hole for peg 3. Add peg 3 and wrap the wire
around this peg, leaving the wire tail adjacent to the hole for peg 4. Add peg
4 and wrap the wire around this peg, leaving the tail adjacent to the hole for
peg 5. Add peg 5 and wrap the wire around peg 5 as shown at right.
Remove the wire from the jig and cut the excess. Close the loop made on
peg
5
with
your
bent
chain
nose
pliers.
The bottom, 3 loop wire component for the earrings shown above-right, is
made using the same steps and procedures as you used for making the 5
loop wire component, only with three pegs and three loops. The peg patterns
for making this component uses pegs 1, 2, and 3 as shown at right.
The bottom wire component on the earrings shown at right is made using the
5 pegs shown below-right. This component is made with 2 1/2 inches of 20
gauge wire. Begin by cutting and making a loop in the end of your wire, then
using this loop to straighten the wire. Start on your jig with pegs 1 and 2.
Place the initial loop on peg 1 and make a loop around peg 2 leaving the wire
adjacent to the hole for peg 3. Continue by adding peg 3 and making a loop
around peg 3, then adding peg 4 and 5 in turn. (When I made this
component, I flipped the wire over after every loop that I made so that the final
loop ended up on peg 1. This is optional, and probably not recommended the
first time you make this component.) Once all five loops are completed,
remove the wire from your jig and cut the excess wire. Close the final loop
with your bent chain nose pliers.
At this point, we will have made the wire components necessary to assemble
these earrings and we will need to begin assembling the earrings.
Instructions for making these earrings continue on the following web page.
he first step in assembly of these earrings is to connect a bead to the middle loop of the top
re component. This is accomplished with a head pin inserted into a bead connected as a
ead dangle to the middle loop in the top wire component. Instructions for this jewelry making
chnique can be found here.
he second step in the assembly of these earrings is to connect the top wire component and
e 5 loop wire component as shown at right. (The bead is not shown in this picture.) Making
is connection is accomplished by opening the loop on one side of the top wire component and
onnecting that loop to one of the end loops on the 5 loop wire component, then closing the
op in the top wire component. To connect the opposite end of the two components, both the
nd loop in the 5 loop wire component and the end loop in the top wire component must be
pened. The two loops are then connected and once connected, both loops are closed. At this
oint
we
are
ready
to
start
adding
beads.
egin with three teardrop beads and three head pins. Insert the head pins into all three beads
nd hang the beads from the center and the two end loops on the 5 loop wire component.
ow we are ready to connect the 5 loop wire component to the bottom wire component. Using
etween 2 1/2 and 3 inches of 22 or 24 gauge wire, make a wrapped bead link, connecting the
mpty loop in the 5 loop wire component made on Peg 2, with one of the end loops on your
ottom wire component. The jewelry making technique for making the wrapped bead link can
e found here. Once that connection is completed, do the same thing with the remaining
mpty loop in the 5 loop wire component and the opposite end of the bottom wire component.
nce these wire components are connected, take three beads and three head pins and
onnect the beads to the bottom three loops in the bottom wire component using your head
ns.
t this point you are ready to connect the ear wire finding to the middle loop in the top wire
omponent either by your modified figure 8 connector or directly. This is done by opening the
ops in the modified figure 8 connector using your bent chain nose pliers, connecting the
omponents and closing the loops. This completes the assembly of this earring.
Here is an alternative but similar design made on the WigJig Delphi or the
square peg pattern part of the WigJig Centaur. For these earrings we elected
to use "Style 2" for our top wire component and were able to eliminate the
need for a modified figure 8 connector. For this reason, there are three wire
components in these earrings plus an ear wire finding. The three wire
components are the top wire component, the 5 loop wire component and the
3 loop wire component.
The top wire component is made using the patterns shown at right. This
component is made with about 2 inches of 20 gauge wire. The steps in
making this wire component are the same as the steps that we described
previously. Simply stated they are cut the wire, make a loop, straighten the
wire, position your pegs on the jig, wrap the wire around the pegs, remove the
wire from the jig, cut the excess wire, close the final loop, convert the initialTop
and final loops to eye loops and finally to rotate the initial and final loops 90
degrees. The finished wire component will appear as shown at right.
The peg patterns for the 3 loop and 5 loop wire components are shown at
right. The 3 loop component uses 1 3/4" of 20 gauge wire and the 5 loop wire
component uses 3 1/4" of 20 gauge wire. Remember that when you are
making a multi-peg pattern, start with just two pegs and add pegs as you go.
After wrapping the wire around the pegs as shown, remove from the jig, cut
the excess and close the final loop with your bent chain nose pliers.
Wire
Component
In the following web page, we will describe another alternative design for similar 2 Tiered V Shaped
Chandelier Earrings that will also use the square peg pattern of the WigJig Delphi or the WigJig Centaur.
This earring design combines the V Shaped Wire Component from our
Chandelier Earrings with the Style 2 Top Wire Component and the 5 Loop
Bottom Wire Component shown on page 17. These earrings can be made
with or without the modified figure 8 connector. The earrings at right have
this connector.
The earrings at right were made using 18 gauge wire instead of the 20
gauge wire used in our prior patterns.
The top wire component is made using the peg pattern shown at right and
using the steps described in this section previously.
The V shaped wire component is made using the peg pattern at right.
Remember to start with just 2 pegs and add a peg as you need it as you
make this wire component. Instructions for making this component can be
found here.
We have described a lot of options for making multi-tier chandelier earrings. We have options using 4mm
beads and other options using 6mm beads. We have options using 18 gauge wire for the body
components and other options that used 20 gauge wire for the body components. We show many
different styles of top wire components used to connect the body of the earring to the ear wire finding,
and many style of body components. Some of the patterns we used required a jig with a round peg
pattern, some of the patterns required a jig with a square peg pattern. There are many more
combinations that could be explored. For now, we are going to move on away from tiered earrings and
begin to investigate ways to make a complimentary yoke as a necklace component. This new necklace
project will be coming soon!
MI WIGJIG CASERO
Realizado con metacrilato, se trata de 2 placas que se ajustan con 2 tornillos
para meter y sacar los tornillos que servirn de base para dar forma al alambre
El wigjig alto lleva un agujero en sus patas para insertar un entorchador
Si haceis clic en sus fotos vereis una ampliacin.
Podeis realizar uno imprimiendo la plantilla que se proporciona en formato pdf
junto a los modelos de wigjig.
enfilador rpido: usamos este aparato para enfilar rapidamente los abalorios
Pon el cuenco boca abajo y con un cutter o cuchillo haz un pequeo corte,
mete unas tijeras en ese hueco y ve girndolas haciendo que se coman el
plstico haciendo asi un agujero redondo. Ve probando el palo y mtele cuando
el tamao del agujero sea el adecuado (es mejor tener que empujarle un poco,
si te pasas tiene peor arreglo), introducele desde abajo. Si quieres asegurarlo
pon pegamento, yo no le he puesto pq no lo veo necesario.
Ahora tan solo tienes que rellenarle con abalorios e insertar la aguja o alambre
con el que vas a enfilar. Con la otra mano gira el palo en sentido contrario, esto
hara que todo el cuenco se mueva y vayan insertandose los abalorios en el hilo
(la punta del hilo siempre quieta comienza poniendola en el fondo y ve
subiendo un poco). Ve deslizando los abalorios hacia atrs cuando tengas unos
cuantos metidos y vuelve a introducir el cabo del hilo en el fondo del cuenco.
FOTOS TOMADAS DE ESTOS LINKS
http://kimberlychapman.com/crafts/beadspinner.html
casero)
http://www.beadspinnerlady.com/
http://www.blessedbeads.com/misc.htm
(muestra
uno
PLANTILLAS
MARGARITAS:
margarita
margarita
margarita
doble
margarita
triple
TRIANGULOS
RED
pequea
simple
doble
centro
grande
PUNTADAS:
peyote
comanche
en circulos
JOYERO DE LUCIA
COLOCACION DE
COLLARES
CONO,
CORCHERA
BUSTO
COLOCACION EN CORCHERA(aerismaud)
ANILLOS
ANILLO DE FLORES
Pulsera y Anillos
Anillo Solitaire
Anillo Jardn
Fournitures
La explicacin no est en espaol, pero con slo ver las imagenes es suficiente
para entenderlo.
3) Sur le fil rouge , enfilez 1 toupie , 1 rocaille , 1 toupie . Puis croisez dans une
facette ou ronde
Sur le fil vert enfilez 1 toupie , croisez dans une rocaille , 1 toupie et croisez dans la
facette
4) Faites glisser les fils dans le montage de manire bien les positionner et
remplir la surface selon le schma 5
5) Ralisez lanneau en enfilant 3 rocailles sur chaque fil puis en croisant dans une
facette .
Rpter jusqu la taille ncessaire de lanneau
6) Rattacher lanneau fini de lautre cot de la bague puis glissez chaque fil tout
autour du motif en glissant une perle de rocaille comme sur le schma
Tobillera