Você está na página 1de 12

OWEN OIL TOOLS LP SONGKHLA THAILAND

Document Title:

TTS Packer/Plug and Straddle Setting


Procedure

Doc. No

: SOP-THA-005

Revision

: 03

Page

Originator

Pirat C.
Description

1 of 12

Revision

Effective Date

00

27-Nov-13

Initial Release

Prathom K.

01

27-Oct-14

Add the contingency plan

Prathom K.

02

30-Apr-15

Revise Job Procedure of set Bottom TTS Retrievable


Packer

Prathom K.

03

17-Jul-15

Review the running procedure

Prathom K.

FM-THA-002

Approval

Date Printed: 24-Aug-15 11:56 AM


The document is uncontrolled when printed from Personal Computer on non-controlled papers

OWEN OIL TOOLS LP SONGKHLA THAILAND

Document Title:

TTS Packer/Plug and Straddle Setting


Procedure

Doc. No

: SOP-THA-005

Revision

: 03

Page

Originator

Pirat C.

2 of 12

1. PURPOSE
The purpose of this standard is to provide the instruction how to set and operate TTS Packer / Plug
and Straddle. This is only for Slick line and E-line Operation.
2. SCOPE
This standard shall be applicable to all Owen Oil Tools LP operation and the operation under Owen
supervision and products.
3. PROCEDURE
3.1. The following equipment is required:
3.1.1. This system can be set and retrieved using Slick Line and E-line.
3.1.2. Gauge Cutter and/or wire brush assy >>is needed of each tubing size.
3.1.3. >>Electric Slick Line Firing Head (for Slick Line)
3.1.4. MSST or Hydrostatic setting tools,
3.1.5. TTS Equipment running gear
No.
1
2
3
4
5
6
7
8

Description
E-line Running tool assy for PIIP
E-line Extension
E-line Running tool redress kit
Setting Sleeve, TTS Packer
Deployment Sub for anchor latch PBR, TTS
Retrieving tool for TTS Packer
E/Q Prong for TTS Packer
Redressing tool for E-line running tool

FM-THA-002

Date Printed: 24-Aug-15 11:56 AM


The document is uncontrolled when printed from Personal Computer on non-controlled papers

OWEN OIL TOOLS LP SONGKHLA THAILAND

Document Title:

TTS Packer/Plug and Straddle Setting


Procedure

Doc. No

: SOP-THA-005

Revision

: 03

Page

Originator

Pirat C.

3 of 12

>>Running Procedure
3.2.

Conduct >>a Job safety Analysis (JSA) meeting with all people involved. Complete handover
operational procedure (SOP) before continuing.

3.3.

Well Preparation
3.3.1. Owen strongly recommends CLEANING tubing on the setting area with >>gauge
cutter, wire brush, junk basket and tubing broach, properly with each tubing sizes.
3.3.2. Drift run TTS dummy per running diagram design.

3.4.

TTS Dummy Run


3.4.1. >>Make up Dummy TTS Retrievable Packer with E-line / Slick line tools string (seal
element not requires).
3.4.2. RIH with above Dummy TTS to correlate ensure target depth is clear. >>RIH with
dummy TTS to identify and verify the depth of perforation to be isolated
3.4.3. , If possible then correlate and mark cable. Check and record pick up tensions.
Note: Use CCL to identify and verify perforation interval if possible.
3.4.4. POOH and rig down dummy run.
3.4.5. Verified or confirm the setting depth, >>Avoid seal elements not on collar or any
profile. If on collar or any profile discuss and agreement >>for adjustment the setting
depth.

FM-THA-002

Date Printed: 24-Aug-15 11:56 AM


The document is uncontrolled when printed from Personal Computer on non-controlled papers

OWEN OIL TOOLS LP SONGKHLA THAILAND

Document Title:

TTS Packer/Plug and Straddle Setting


Procedure

Doc. No

: SOP-THA-005

Revision

: 03

Page

Originator

Pirat C.

3.5.

4 of 12

>>Actual Retrievable Packer and Straddle


3.5.1. Retrievable Packer
1) Make up proper size of TTS Retrievable Packer with E-line / Slick line tools
string. Check and record TTS S/N, Equalizing sub S/N, then measuring tools
string length and sizes.
2) RIH with retrievable TTS Packer with speed not more than 250 ft. / min. Slow
down when pass restriction nipple profile and perforation zone as when tagging
top of fluids. Monitor CCL depth and tensions.
3) Using the cable mark for getting on depth with slowest upward speed (30ft min
maximum). Verify the depth to be set with the distance of CCL to middle seal
element. Record SITP before and after setting.
4) Initiate firing sequence to set the TTS packer. Check for setting indication by
sudden decrease of tension. Wait for 5 minutes to make sure MSST is elongated
and the plug seal material is energized. Before and after firing need to check
and record pick up tensions.
Note: The reason for avoiding correlating with actual TTS packer run and
using marked cable to get on depth is to prevent getting stuck due to the
swelling of the element.
5) POOH to the surface, close swab valve, bleed off pressure and retrieve the
setting tool out of the lubricator. Inspect the MSST, redress and clean it for the
next job. Re-new cable head if necessary.
Caution: Beware of pressure trap when redressing MSST

FM-THA-002

Date Printed: 24-Aug-15 11:56 AM


The document is uncontrolled when printed from Personal Computer on non-controlled papers

OWEN OIL TOOLS LP SONGKHLA THAILAND

Document Title:

TTS Packer/Plug and Straddle Setting


Procedure

Doc. No

: SOP-THA-005

Revision

: 03

Page

Originator

Pirat C.

5 of 12

6) >>Optional Deploy Junk Catcher TTS plug


a)

Prepare proper junk catcher with deployment sub, install to wireline / slick
line tools string.

b)

Check and record anchor latch S/N, then measuring tools string length
and sizes.

c)

RIH with speed not more than 250 ft. / min. Slow down when pass
restriction nipple profile and perforation zone as when tagging top of
fluids.

d)

Check tension 50 ft. above TTS plug before latching. Slowly down to
latching, and ensure to be latched by making over pull 100 200 lbs.
from normal tensions.

e)

Activated jar down shear screw to release junk catcher. Pick up normal
tension and tools free. POOH.

f)

On surface rig down.

3.5.2. >>TTS Straddle Retrievable Patch


1) Set Bottom TTS Retrievable Packer
a) Make up proper size of TTS Retrievable Packer with E-line / Slick line
tools string. Check and record TTS S/N then measuring tools string
length and sizes.
b) RIH with retrievable TTS Packer with speed not more than 250 ft. / min.
Slow down when pass restriction nipple profile and perforation zone as
when tagging top of fluids. Monitor CCL depth and tensions.

FM-THA-002

Date Printed: 24-Aug-15 11:56 AM


The document is uncontrolled when printed from Personal Computer on non-controlled papers

OWEN OIL TOOLS LP SONGKHLA THAILAND

Document Title:

TTS Packer/Plug and Straddle Setting


Procedure

Doc. No

: SOP-THA-005

Revision

: 03

Page

Originator

Pirat C.

6 of 12

c) Using the cable mark for getting on depth with slowest upward speed
(30ft min maximum). Verify the depth to be set with the distance of CCL
to middle seal element. Record SITP before and after setting.
d) Initiate firing sequence to set the TTS packer. Check for setting
indication by sudden decrease of tension. Wait for 5 minutes to make
sure MSST is elongated and the plug seal material is energized. Before
and after firing need to check and record pick up tensions.
Note: The reason for avoiding correlating with actual TTS packer
run and using marked cable to get on depth is to prevent getting
stuck due to the swelling of the element.
e) POOH to the surface, close swab valve, bleed off pressure and retrieve
the setting tool out of the lubricator. Inspect the MSST, redress and
clean it for the next job. Re-new cable head if necessary.
Caution: Beware of pressure trap when redressing MSST
Caution: During RIH if Packer gets stuck on nipple
Recommend to fire MSST to set Packer, and then retrieve later
on.
NOT recommend to break weak point (Tools String will become fish with
Explosive).
f) Contingency Plan: If MSST Tool doesnt activate and packer fails to set.
In form to customer representative onsite.

FM-THA-002

Date Printed: 24-Aug-15 11:56 AM


The document is uncontrolled when printed from Personal Computer on non-controlled papers

OWEN OIL TOOLS LP SONGKHLA THAILAND

Document Title:

TTS Packer/Plug and Straddle Setting


Procedure

Doc. No

: SOP-THA-005

Revision

: 03

Page

Originator

Pirat C.

7 of 12

Repeat step tool firing sequence monitor indication on E-line


company system, if tool activate wait 5 minutes for MSST to fully set.
If not activate confirm to customer representative onsite to pull out
of hole to surface investigate check.
Caution: While pull out of hole slow down pass thru at
restriction area.
2) >>Set Flow tube section
a) Make up tool Slickline tool string with Deployment tool(this can be run on
E-line if required)
b) Make up PBR with flow tubing length according well condition connect
to Anchor latch.
c) RIH tools string with flow tube section assembly. Before latch check
normal pickup weight then run down slowly to latch top of bottom TTS
packer (If unable to latch change different speed) Pick up 100-200 lbs.
over pull to verify Anchor Latch was successful and then jar down to
shear of running tool.
d) POOH to surface.
e) Repeat step a) d) until flow tubing section cover perforation interval per
diagram design.
Note: Deployment flow tubing section depending perforation
interval
f) Contingency Plan: If tool unable to successful latch.

FM-THA-002

Date Printed: 24-Aug-15 11:56 AM


The document is uncontrolled when printed from Personal Computer on non-controlled papers

OWEN OIL TOOLS LP SONGKHLA THAILAND

Document Title:

TTS Packer/Plug and Straddle Setting


Procedure

Doc. No

: SOP-THA-005

Revision

: 03

Page

Originator

Pirat C.

8 of 12

Repeat step to pull out and run with difference speed to and pick
up 100-200 lbs. to verify successful latch.
If jar down to shear of running tool not success increase the time to
jarring.
If not success to latch confirm to customer representative onsite to
pull out of hole to surface investigate check.
Caution: While pull out of hole slow down pass thru at
restriction area.
3) Set Top TTS Retrievable Packer with top section flow tubing
a) Make up TTS Retrievable packer complete with Equalizing sub, Flow
tube and Anchor Latch seal assy with setting tool.
Remark: Select the shear screws on anchor latch all way the lower one
stronger that the top one
b) >>Make up proper size of TTS Retrievable Packer with E-line / Slick line
tools string. Check and record TTS S/N, Equalizing sub S/N, anchor
latch S/N then measuring tools string length and sizes.
c) RIH with retrievable TTS Packer with speed not more than 250 ft. / min.
Slow down when pass restriction nipple profile and perforation zone as
when tagging top of fluids. Monitor CCL depth and tensions.
d) Using the cable mark for getting on depth with slowest upward speed
(30ft min maximum). Verify the depth to be set with the distance of CCL
to middle seal element.

FM-THA-002

Date Printed: 24-Aug-15 11:56 AM


The document is uncontrolled when printed from Personal Computer on non-controlled papers

OWEN OIL TOOLS LP SONGKHLA THAILAND

Document Title:

TTS Packer/Plug and Straddle Setting


Procedure

Doc. No

: SOP-THA-005

Revision

: 03

Page

Originator

Pirat C.

9 of 12

e) RIH tools string with TTS top section assembly. Then Before latch check
normal pickup weight then run down slowly to latch top of bottom TTS
packer (If unable to latch change different speed) Pick up 100-200 lbs.
over pull to verify Anchor Latch was successful. Ensure setting depth is
correct. Record SITP before and after setting.
f) Initiate firing sequence to set the top TTS packer assembly. Check for
setting indication by sudden decrease of tension. Wait for 5 minutes to
make sure MSST is elongated and the plug seal material is energized.
Before and after firing need to check and record pick up tensions.
Note: The reason for avoiding correlating with actual TTS packer
run and using marked cable to get on depth is to prevent getting
stuck due to the swelling of the element.
g) POOH to the surface, close swab valve, bleed off pressure and retrieve
the setting tool out of the lubricator. Inspect the MSST, redress and
clean it for the next job. Re-new cable head if necessary.
h) Rig down tools string and equipment.
Caution: Beware of pressure trap when redressing MSST

FM-THA-002

Date Printed: 24-Aug-15 11:56 AM


The document is uncontrolled when printed from Personal Computer on non-controlled papers

OWEN OIL TOOLS LP SONGKHLA THAILAND

Document Title:

TTS Packer/Plug and Straddle Setting


Procedure

Doc. No

: SOP-THA-005

Revision

: 03

Page

Originator

Pirat C.

3.6.

10 of 12

TTS Packer Retrieve Plan


3.6.1. This can all be done using Slickline make up S/L tool string connect with TTS Retrieve
tool.
3.6.2. Optional for Top Junk catcher - Active jar up to xxxx lbs. shear screws release
Anchor latch tool free pull out of hole.
3.6.3. RIH TTS Retrieval tool with proper equalize prong to latch top of TTS Packer slowly
TAP down 3 times to shear 1,600 lbs. (New Style) or 800 lbs. (Old style) Equalizing
sub, make over pull 200 300 lbs., sit back down. Wait for equalized pressure.
3.6.4. Active jar up to 4,800 lbs. shear screws retract slip, standby 1 hour or more for allow
packing retract.
3.6.5. Rig down slick line equipment.
Contingency Plan: If slick line company to retrieving the TTS packer.
Slick line company need to inform back to them supervisor
Slick line company supervisor will co-operate with Owen operation
coordinator to advice.

3.7.

TTS Straddle Patch Retrieve Plan


3.7.1. This can all be done using Slickline make up S/L tool string connect with TTS Retrieve
tool and equalizing prong.
3.7.2. RIH TTS Retrieval tool to latch top of TTS Packer slowly TAP down 3 times to shear
1,600 lbs. (New Style) or 800 lbs. (Old style) Equalizing sub, make over pull 200
300 lbs., sit back down.

FM-THA-002

Date Printed: 24-Aug-15 11:56 AM


The document is uncontrolled when printed from Personal Computer on non-controlled papers

OWEN OIL TOOLS LP SONGKHLA THAILAND

Document Title:

TTS Packer/Plug and Straddle Setting


Procedure

Doc. No

: SOP-THA-005

Revision

: 03

Page

Originator

Pirat C.

11 of 12

3.7.3. Active jar up to 4,800 lbs. shear screws retract slip, standby 1 hour or more for allow
packing retract.
3.7.4. Active jar up to 800 lbs. shear screws release Anchor latch tool free pull out of hole
3.7.5. RIH TTS Retrieval tool (without equalizing prong) latch top PBR jar up to XX Lbs. to
shear release Anchor latch @ x,xxx m., tool free pull out of hole.
3.7.6. RIH TTS Retrieval tool to latch top of lower TTS Packer and firmly retrieve tool latch to
fish neck body of TTS packer. Active jar up to 4,800 lbs. shear screws slip retract
and standby 1 hour allow packing element retract, free pull out of hole.
3.7.7. Rig down slick line equipment.
Contingency Plan: If slick line company to retrieving the TTS packer.
Slick line company need to inform back to them supervisor
Slick line company supervisor will co-operate with Owen operation
coordinator to advice.

FM-THA-002

Date Printed: 24-Aug-15 11:56 AM


The document is uncontrolled when printed from Personal Computer on non-controlled papers

OWEN OIL TOOLS LP SONGKHLA THAILAND

Document Title:

TTS Packer/Plug and Straddle Setting


Procedure

Doc. No

: SOP-THA-005

Revision

: 03

Page

Originator

Pirat C.

12 of 12

Figure 1: Example TTS Straddle Patch Retrieve Diagram.

FM-THA-002

Date Printed: 24-Aug-15 11:56 AM


The document is uncontrolled when printed from Personal Computer on non-controlled papers

Você também pode gostar