Escolar Documentos
Profissional Documentos
Cultura Documentos
Prepared By
Document Version
Last Updated On
Thinnk Ware
80 REVP1.00
10 JUN,2010
Page 1/9
SAFETY INSTRUCTIONS:................................
................................................................................................
................................................... 3
ABOUT RoBoNiche:................................
..............................................................................................................................
.............................. 3
BLOCK DAIGRAM:................................
..............................................................................................................................
.............................. 4
PARTS DESCRIPTION & CONNECTIONS WITH ATMEL:.............................................................
ATMEL:
............................. 5
SWITCHES: ................................................................................................................................
................................
....................................... 5
SENSORS:................................................................
................................................................................................
.......................................... 5
LCD: ................................................................
................................................................................................
................................................... 6
LEDS: ................................................................
................................................................................................
................................................ 6
FEATURES: ................................................................
................................................................................................
........................................... 7
BOARD DESCRIPTION: ......................................................................................................................
................................
...................... 8
EXERCISE: ................................................................
................................................................................................
............................................ 9
Page 2/9
SAFETY INSTRUCTIONS:
INSTRUCTIONS
Be careful while using the screw driver, place
assembly on a platform & then tighten the
screw driver. Dont tighten the screw keeping
assembly in your hands, the screw driver may
slip & you could injure yourself. In case of
cuts & bruises, wash your hands with water,
apply antiseptic lotion & consult a doctor
immediately
ABOUT RoBoNiche:
A Complete web portal which has educational Robotics and embedded
product and is growing very rapidly.
Buy Microcontroller Boards, Programmers, Sensor modules, Motors,
Wheels, Robotic Chassis, Robotic Kits, Electronic Components & much
more.
"Tired of searching components" in local markets and at reasonable rates.
Contact us for Setting RoBoNiche in your college or at a place near you. We
will ease your problem and will set up RoBoNiche. Write to us at:
roboniche@thinnkware.com
Page 3/9
BLOCK DAIGRAM:
Page 4/9
SWITCHES:
SW1
SW2
SW3
RST
(PORT3, BIT2)
(PORT3, BIT3)
(PORT3, BIT4)
To reset the microcontroller
SENSORS:
+
S3
S2
S1
S0
VCC
GND
AD4
AD5
AD6
AD7
NOTE:: This port is also used as 8 bit/10 bit ADC input channel.
Page 5/9
LCD:
LCD CONTROL PIN(RS)
LCD CONTROL PIN(RW)
LCD CONTROL PIN(EN)
LCD DATA PINS
(PORT1, BIT4)
GND
(PORT1, BIT5)
(PORT0, BIT0-3)
LEDS:
LED1(D1)
(PORT1, BIT6)
LED2(D2)
(PORT3, BIT0)
LED3(D3)
(PORT3, BIT1)
LED4(D6)
Programming LED
LED5(PWR-ON)
ON)
(PORT 2,BIT(0-3))
(PORT 2,BIT(4-7))
Page 6/9
FEATURES:
8051 Development Board with inbuilt programmer.
On board Voltage Regulator with filters and operating voltage
voltage- 5V to
12V.
DB-99 connector to connect with the serial port of the computer
computer(UART
communication).
On Board IN-circuit
circuit programmer consisting AT89C2051 and
MAX232.
11.0592 MHz Crystal Oscillator for clock pulsing.
In built motor driving circuitry (4 DC / 2 Stepper motor).
2 pin connector to connect the Power Supply.
Red Led as Power Indicator.
Green Led as Programming Indicator.
A reset switch.
A jumper to toggle between Programming circuit and Reset circuit.
All ports accessible through Male Header Pins.
Page 7/9
BOARD DESCRIPTION:
DESCRIPTION
Page 8/9
EXERCISE:
Flash an LED connected to any port line using the set and clear
logic each at the rate of one sec. for ten times.
A simple burglar alarm system has four zone inputs connected to an
i/o port. If any one of these inputs activated a bell will sound for five
min. and the corresponding
corresponding zone LED or LEDS will be
activated.
Write a programme to show the count of the number of the times the
push button switch press on the LCD.
Write a programme to implement a simple calculator using only two
operands of single digit it display the re
result
sult using 4*3 matrix keypad
and an LCD.
Write a programme to count pulse an T0 pin and update the same in
a unsigned variable.
Write a programme to serially transmit the message HELLO
WORLD on serial window/pc hyper terminal window.
Write a programme to test how 8051 respond to various types of
interrupts.
Manufactured by:
Thinnk Ware
A venture of KC Robotics & Embedded Pvt. Ltd.
C-20/1 JSSATE-STEP
STEP Sector-62
Sector
Noida (U.P.)-201301
201301
Phone: +91-120-649-4440
4440
Mobile: +91-9211-786-062
062
Fax: +91-120-2401451
Page 9/9