Você está na página 1de 5

Page 1 of 5

From: Ruth DeLaMater Bundy or Ralph Charles Whitley, Sr.


Date: 5/27/2010 2:02:38 PM
To: mbunker@brenelle.com
Subject: Fw: Re: SOLUTION IS PATENTED IDEA FROM BRENELLE ENTERPRISES IN TEXAS .......Fw: 051510 MAYDAY, MAYDAY, MAYDAY ---
MATTER OF NATIONAL SECURITY Great Oil Disaster Pictures

-------Original Message-------

From: Ruth DeLaMater Bundy or Ralph Charles Whitley, Sr.


Date: 5/27/2010 2:01:12 PM
To: Brent Larkin; horizonsupport@oegllc.com; info@deepwater.com; Innovative.Technology@dep.state.fl.us; mepatriot@juno.com; president@whitehouse.gov;
John O. Brennan The White House; mailtothechief@cnn.com; President Barack Obama; charlie.crist@myflorida.com; bobby.jindal@la.gov; CFO Alex Sink; Senator
Bill Nelson
Subject: Re: SOLUTION IS PATENTED IDEA FROM BRENELLE ENTERPRISES IN TEXAS .......Fw: 051510 MAYDAY, MAYDAY, MAYDAY --- MATTER OF
NATIONAL SECURITY Great Oil Disaster Pictures

The riser has a 21 inch OD with thickness of wall rated at .812 or something similar LESS THAN ONE INCH THICKNESS indicated on the GE
site. Go to www.drillingahead.com and look left side for Deepwater Horizon EXPLOSION blogs going from 1 to 18 looking at the
PROFESSIONAL HANDS comments and the information on type of pipe is there with that Google same and find the exact models.

"The BP spill riser is 21-inch pipe. 4-inch pipe has 3.6% the cross-section area (as radius^2) and 0.13% the fluid conductance (as radius^4). Things are
no better allowing for respective wall thicknesses. Vetco HMF Class H 21-inch riser pipe has .812" walls. The oil cannot be meaningfully sucked
upwards because it is rich with methane, 3000:1 gas:oil according to BP.

Thick horseshoe of medium velocity explosive (surface mining gel explosive) with an inner lining of high density pusher (lead; lead-tungsten composite)
about the hollow center, then a collapsible gap spacer. Slide it snug around the riser, then detonate at the outside curved end. The riser crimps shut
when the implosion tamper arrives on both sides. Think of it as a channel charge designed to hammer not cut.

Was that so difficult? A donut may have problems of closing a clamshell around the riser, symmetric detonation, and where intervening mass goes as
the implosion tamper ring constricts."

MY PERSONAL REPLY COMMENT IS DO NOT USE EXPLOSIVES NEAR THIS ESCAPING GAS OR YOU MAY SEE IXTOC 2 IN EASTERN GULF OF MEXICO !

APPARENTLY WALL THICKNESS IS .812 Inches which would allow the Branko Richard Babic CPP with flow thru pipe to work with that special beveled
flange and SLEEVE of thick wall pipe 22 INCHES ID maybe 4 feet thick guided down by ROV over the cut riser or pulled left or right to cut horizontally
section which can be pulled and pushed inside the riser in a similar fashion then ROV bore HOLES, TAP SAME and use heavy BOLTS to pull it and hold it
in place even if extra steel with huge bolts and nuts could PULL same into the riser.   That was suggested to KEEP the rig working but now it appears
the underground sections have been pulled OUT by the force with the Deepwater Horizon not having ENGINES FOR THRUSTERS TO KEEP IT IN
POSITION so everything pulled, filled with water, collapsed in the fires of fuel and gas then SUNK twisting and braking loose from Deepwater Horizon
whiich, along with the bodies are no doubt on the bottom.  
 
BP was given the CPP without Pipe and shutoff to get weights on same and force into three leaks...one attached formerly to Rig, one back on floor of
sea bed then one near the BOP attachment.   NO ONE CALLED NOR CALLED THE INVENTOR BABIC IN OXFORD ENGLAND and they could have made up
an exact replica in a welding shop, supported the PIPE with blocks then pushed same down inside a similar 21 inch OD riser pipe with .813 inch walls. 
NOTHING WAS DONE !
 
Horizontal SEALING with Branko R. Babic CPP with pipe just under size of flowing pipe would have allowed FULL PULL OFF OF ALL GAS, OIL AND
WATER to the surface AFTER ROV WITH CUT SAW HYDRAULIC 50 INCH WHEEL CUT AWAY THE PIPE CLEAN FOR INSERTION..... NOTHING DONE.  The
BOP has a connection perhaps a type of flange where IT could be removed then pipe cut and NEW FLANGE ITEM FOR BOP replaced with SHUTOFF but
no one has done anything.
 
My fear is the BOP connection going into the ground X number of feet to meet with another smaller pipe with annular possibly damaged from TORQUE or
PRESSURE PULL could easily be a problem quickly if MOTHER NATURE PUSHES UP THE BOP SECTION DAMAGED IN A BELCH OF PRESSURE.   I would
have felt better seeing the GIANT SQUARE HEAVY OBJECT LOWERED OVER THE BOP but that will not happen now that the ENGINEERS contacted the
EXPERTS AND BOP MANUFACTURER TO REALIZE PLAN B WAS TO TOP KILL THEN PLAN C WOULD BE X AND FINAL PLAN D WOULD BE X.
 
We encouraged EVERYONE TO TALK WITH THE PEMEX EXPERTS ON HOW THEY STOPPED THE RUAWAY WELL IXTOC 1 IN 1979.   THE TECHNIQUE
FORCING LEAD BALLS UNDER HIGH PRESSURE BELOW THE BOP SEALING NOT ONLY THE BOP BUT PUTTING LEAD FORCED INTO SOME 300 FEET OF
UNDERWATER CASING WITH THE LEAD FLATTENING OUT FOR SAY 300 FEET MAY INDEED SEAL THE WELL PERMANENTLY IF THEY FOLLOW
TECHNIQUES FROM IXTOC 1 IMMEDIATELY !
 
As indicated I HOPE AND PRAY the other risers have shutoff valves and hydraulic oil check valves so that in any emergency in the future like
EARTHQUAKE OR MAN MADE DISASTER LIKE THIS ONE, ALL WILL NOT SIMPLY PULL OUT THE BOP LINES AND HAVE UNCONTROLLABLE GAS AND OIL
FILLING THE GULF AND THE GAS CLOUDS THREATENING EVERYTHING AND OIL THREATENING THE ENVIRONMENT DAMAGING SAME FOR 10-20
YEARS LIKE CHERNOBYL WILL NEVER BE THE SAME.
 
I FEAR, AS YOU DO, THE NUCLEAR POWER PLANTS NOT BEING ABLE TO SHUT DOWN WITH A CLOUD KILLING ALL PEOPLE IN A PARTICULAR AREA
PLUS FEAR GAS HITTING INTAKES FOR ALL MOTORS AND MACHINERY, KILLING PEOPLE ALL OVER FLORIDA OR THE GULF COAST WITH NO OXYGEN
AS THE GAS IS HEAVIER THAN AIR......ANYONE CAN DEAL WITH THE STENCH OF ROTTING FISH, BIRDS AND SEA CREATURES BUT THE STENCH OF
ROTTING HUMAN FLESH IS REALLY SOMETHING WHICH WILL BE UNBEARABLE PLUS IN FLORIDA ALONE SOME 200 MILLION BODY BAGS AND
CREMATION WITH BP OIL RESIDUE WILL BE NECESSARY OR ALL THE WATER AND WATER TABLES WILL BE CONTAMINATED AND NOT SAFE TO DRINK
ANYWHERE ON THE GULF COAST AND FLORIDA........... NOW THAT IS SOMETHING THE PRESIDENT MUST KEEP IN MIND WHEN DECIDING TO HAVE BP
MOVE OVER AND LET THE USCG, MILITARY AND U.S. NAVY SEA BEES STOP THE LEAK NOW !
 
Of course, like me Brent, you too will be able to send in suggestions and someday there might be a government official who decides to check with the
NAVY SEA BEES AND NAVY DIVERS to see this would actually work and stop the well.....even PEMEX would help as the spill could move WEST
endangering them like IXTOC 1.
 
AGAIN --- THE SLEEVE OF WELDED PIPE WAS TO STOP SPLITTING THE THIN WALL .813 INCH 21 INCH RISER WITH SUPER FORCE FROM 30,000

5/27/2010
Page 2 of 5

POUNDS OF WEIGHT.
 
CHECK WITH BRANKO RICHARD BABIC ON WHETHER THIS DOUBLE SEALING INSIDE HEAVY WALL THICK PIPE SLEEVE IS A GOOD IDEA OR BAD IDEA !
 
Ralph
052710 @ 2:01 PM OR 7:01 PM England

Ralph Charles Whitley, Sr.  CFC032631


Backflow Prevention, Inc.
4532 W. Kennedy Blvd. PMB-276
Tampa, Florida 33609-2042 USA
Phone: 813-286-2333

SKYPE:  ralphwhitleysr

URL:   http://www.scribd.com/ralphwhitleysr 

E-MAIL:  Backflow2@verizon.net 

-------Original Message-------

From: Brent Larkin


Date: 5/27/2010 12:42:29 PM
To: Ruth DeLaMater Bundy or Ralph Charles Whitley, Sr.
Subject: Re: SOLUTION IS PATENTED IDEA FROM BRENELLE ENTERPRISES IN TEXAS .......Fw: 051510 MAYDAY, MAYDAY, MAYDAY --- MATTER OF
NATIONAL SECURITY Great Oil Disaster Pictures

Ralph,

Did you ever get anyone to let you know what the Inside Diameter of the pipe is? I can't get a response. Do you have the email addresses of BP or
anyone else that may know the true I.D. size? Without the true size, ( not speculated ) my hands are kind of tied.
Send me the emails and I'll keep at it.

Thanks,
Mark Bunker
Brenelle Enterprise
Jet Swet
----- Original Message -----
From: Ruth DeLaMater Bundy or Ralph Charles Whitley, Sr.
To: mbunker@brenelle.com
Cc: horizonsupport@oegllc.com ; John O. Brennan The White House ; info@deepwater.com ; ri@dcf.pemex.com ; president@whitehouse.gov ; bobby.jindal@la.gov ;
charlie.crist@myflorida.com
Sent: Monday, May 17, 2010 11:51 AM
Subject: SOLUTION IS PATENTED IDEA FROM BRENELLE ENTERPRISES IN TEXAS .......Fw: 051510 MAYDAY, MAYDAY, MAYDAY --- MATTER OF NATIONAL SECURITY Great
Oil Disaster Pictures

Ladies and Gentlemen:

Mr. Bunker at Brenelle Enterprises, Inc. In Texas was contacted and he also agrees that insertion of perhaps an 18 inch pipe using
the patented idea from Brenelle on their JET SWET configuration using 18 inch flow thru thick wall pipe and ball valve with flange
would SEAL THE INTERIOR OF THE 21 INCH OUTSIDE DIAMETER RISER PIPE. One thing he would need immediately is to know the
INSIDE DIAMETER OF THE RISER PIPE in order to get the patented idea made with even 18 inch heavy wall pipe.

We discussed the fact that BP through a ROV could CUT CLEAN AROUND THE PIPE WHERE YOU HAVE INSERTED A 6 INCH PIPE
TO COLLECT OR DRAIN OFF OIL AND GAS PERHAPS. Such would allow a clean opening NOT BENT to be the next challenged
insertion point with TAPERED STEEL WASHERS POINTING TO THE ENDS AND HUGE RUBBER COMPRESSION ITEMS INBETWEEN
WITH STEEL PLATING WELDED ON THE UPSTREAM SIDE THEN SPECIAL THREADED SECTION CLEAR OF THE DOWNSTREAM
WASHER WHERE THE ROV ASSISTING CAN TWIST RIGHTY TIGHTY TO SEAL THE INTERIOR OF THE PIPE WHILE ALLOWING FULL
FLOW TO CONTINUE DOWNSTREAM THROUGH A FLANGE WELDED ON THE PERHAPS 18 INCH PIPE WHICH WOULD ALLOW A
BALL VALVE AND ANOTHER FLANGE TO FLANGE CONNECTION MADE UP THEN YOUR RISER COULD BE FITTED WITH A
WATERPROOF SEAL AREA FLANGE TO BALL VALVE THEN ONCE REMOVING THE WATERPROOF SEAL AND ATTACHING OPEN
TO THE FLANGE THE OPTION WOULD BE TO TAKE 18 INCHES OF OIL AND GAS TO THE SURFACE AND ALSO BE ABLE TO SEAL
THE LINE LATER.

NOW AS BEFORE....I WOULD ENCOURAGE EACH OF YOU TO CONSIDER USING THE CUT PIPE SECTION TO PUSH A SLEEVED
ITEM TO BE ABLE TO ATTACH L SHAPPED STEEL TO HOLD THE ENTIRE 18 INCH PIPE IN PLACE ...... ALL CAN BE DONE IN 8
HOURS FLAT !

Brenelle will be given other messages pertinent to this idea so they can help ALL seal this leak as one works, two can be added then entire
well secured from leaks UNDERWATER at sea floor with contents pumped to the surface or SHUT DOWN at your leisure.

Ralph 813-286-2333
051710 @ 2:51 PM Eastern MONDAY

-------Original Message-------

From: Ruth DeLaMater Bundy or Ralph Charles Whitley, Sr.


Date: 5/15/2010 2:30:44 PM
To: backflow2@verizon.net
Cc: president@whitehouse.gov
Subject: 051510 MAYDAY, MAYDAY, MAYDAY --- MATTER OF NATIONAL SECURITY Great Oil Disaster Pictures

5/27/2010
Page 3 of 5

MAYDAY......MAYDAY......MAYDAY MATTER OF NATIONAL SECURITY

GULF AND FLORIDA ARE IN DANGER ---PLUS--- BP CANNOT STOP THE FLOW AFTER WELL OVER 20 DAYS !

THIS IS BOTH A MURDER SCENE/NATIONAL EMERGENCY UNTIL CAUSE FOUND OUT AND EVIDENCE BROUGHT TO SURFACE !

BP CANNOT CONTROL OR STOP THE LEAK FOR OVER 21 DAYS AT THE EXPENSE OF THE GULF AND THREE STATES !

P L E A S E LET THE USCG/NAVY TAKE OVER IN THE INTERESTS OF NATIONAL SECURITY !

THE LEAK CAN BE STOPPED WITHIN 8 HOURS USING KNOWN INVENTIONS SUCH AS BRANKO R. BABIC
COUNTER PRESSURE PLUG FORCED INTO THE PIPE JUST AFTER THE BOP ! WOULD KNOW IN 6 HOURS !

http://homepage.virgin.net/babic.branko/kofc.html

Or

JET SWET idea with SOLID STEEL THREADED ROD pulling components high pressure inserted should shut down above BOP

Trying with 2 or 3 inch PIPE threaded at bottom to upstream flow to hold nut and washer forced down with three 5 inch thick rubber
items to expand
Then another washer machined to be able tor remove through full bore BALL VALVE WITH ROUND WHEEL CLOSURE would allow
unit to have
Force to pull up against LINER to seal flow and small ball valve where HOSE attachment shown on a 3 inch pipe would allow fittings
to connect underwater PIPING to pull off OIL and shut the rig down by turning a ball valve on the PIPE later if necessary. LOOK AT
THE PICTURE FOLKS then think inside diameter of WELL PIPING ON FLOOR IS WHAT SIX INCH ? MAKE UP A RIG LIKE THIS OF 4
INCH OR EVEN 3 INCH THEN HAVE THREE RUBBRE SECTIONS WHERE THE BLACK IS LOCATED AND TURNING A NUT BY ROV
ATTACHMENT WITH WHEEL WILL ALLOW ONE ROV TO HOLD IN PLACE WHILE THE OTHER TURNS THE WHEEL PUSHING THE
RUBBER AGAINST THE INTERIOR WALL STOPPING FLOW AND LEAKING GAS FORCING SAME TO GO UP A PIPE TO THE
SURFACE PERHAPS OR SHUT DOWN WITH BALL VALVE, SEAL AND CAP THEN TRY TO SHUT DOWN THE BOP ! Total time 8
HOURS FLAT !

MY GUARANTEED IDEA IF YOU CAN HOLD IT IN PLACE OR PUSH INTO PIPE !!!!!!!---IF IT DOES NOT WORK INSERT ONE WITH 2
INCH OR 1 INCH SOLID STEEL ROD AND TURN WITH WHEEL TO SEAL AGAINST THE PIPE THEN TIE THE PIPE WHEEL AND
PIPE ROD TO THE BOP TOP STOPPING THE WELL AND SEE IF THE BOP CAN BE SHUT DOWN. KEY SHUT OFF SPILL AND
DEADLY GAS GOING TO SURFACE !

BODIES AND RIG PLUS PIPING CAN BE BROUGHT TO THE SURFACE IF NOT TO SHALLOW WATER FOR FLOATING/EXAMINING !

THE LEAK CAN ALSO BE STOPPED CREATING THE INTERNAL EXPANDING PLUG USING SUPER PSI STRENGHT
COMPRESSION WITH 5 INCH THICK RUBBER SECTIONS [THREE OR FOUR MAXIMUM], HEAVY TAPERED STEEL
WASHERS TO ALLOW SUPER PRESSURE THEN ONCE SECURED USING SMITH BLAIR TYPE PRESSURE COUPLINGS
TO PULL WELDED PIPE WITH BALL VALVE TO SEAL THE ENTIRE UNIT OR, IF DEEMED SAFE LATER TO REOPEN AND
REMOVE INTERNAL EXPANDING PLUG, SHUT DOWN BALL VALVE THEN ATTACH SURFACE PIPING WITH A BALL VALVE
TO CONTINUE REMOVING OIL AND GAS AFTER ALL EVIDENCE IS RETRIEVED ALONG WITH BODIES FROM THE BOTTOM.

DANGER.....CAUSE THAT BOP TO BE SHEARED AT THE BOTTOM COULD OR WILL RESULT IN A PIPING BLOWOUT STRAIGHT UP
TO THE SURFACE AND THEN WITH A LIGHTNING STRIKE YOU COULD HAVE IXTOC 2 IN THE GULF NEAR LA. OIL SLICK COULD

5/27/2010
Page 4 of 5

ROUND FLORIDA AND GO UP THE ENTIRE EAST COAST THEN OVER TO EUROPE UNLESS THIS WELL IS SHUT DOWN
IMMEDIATELY ! REMEMBER IXTOC 1 WAS BURNING BELOW THE SEA BED FLOOR....NOT SUPPOSED TO HAPPEN WITHOUT
OXYGEN FEEDING A FIRE ? TELL IT TO MOTHER NATURE !

OIL SHIFTING OUT OF THE GROUND COULD/WILL CAUSE EARTHQUAKES AS THE PLATES SHIFT WITH SO MUCH OIL REMOVED
IN SUCH A SHORT TIME ! THINK ABOUT IT !

THIS MUST BE CONFIRMED AN ACCIDENT AND PEOPLE WILL NEED TO BE POLYGRAPHED AS TO KNOWING THE CAUSE YET
NOT REVEALING WHAT THEY KNOW IN A MURDER INVESTIGATION CAN BRING FEDERAL FELONY CHARGES IN A FLASH !

MAYDAY MAYDAY MAYDAY MATTER OF NATIONAL SECURITY

Ralph Charles Whitley, Sr. CFC032631


Tampa, Florida 813-286-2333
SKYPE ralphwhitleysr

E-mail: backflow2@verizon.net

051510

Ralph Charles Whitley, Sr.


a Decorated American Veteran
4532 W. Kennedy Blvd. PMB-276
Tampa, FL 33609-2042 USA

Phone: 813-286-2333
backflow2@verizon.net

This transmission may be NOT BE DECLARED CONFIDENTIAL NOR PROTECTED from disclosure and is NOT only for review and use by the intended recipient. Access by
anyone else is NOT unauthorized. Any authorized reader is hereby notified that any review, use, dissemination, disclosure or copying of this information, or any act or
omission taken in reliance on it, is NOT prohibited and may NOT BE CONSIDERED UNLAWFUL. If you received this transmission in error, please notify the sender
immediately. Ruth D. Bundy. GRI, Broker-Associate MARK IT REALTY GROUP, INC., 332 W. Bearss Avenue, Tampa, FL 33613-1228 Phone: (813) 286-2333 FAX: (813) 636-
4022 Backflow Prevention Assembly Test/Repair or Installation at BACKFLOW PREVENTION, INC. CFCO32631, 4532 W. Kennedy Blvd., PMB 276, Tampa, Florida 33609-
2042 Phone: (813) 286-2333 or Fax (813) 636-4022 via e-mail to Ruth D. Bundy or Ralph Charles Whitley, Sr. CFC032631 backflow2@verizon.net . REV2/07192009
-------Original Message-------

From: Peter Rogers


Date: 5/15/2010 1:36:02 PM
Subject: [apfn-1] Great Oil Disaster Pictures

Folks,

This is the best series of pictures I have seen - connecting us to the reality of the tragedy unfolding in the Gulf of Mexico.....

Check 'em out !!

Special thanks to my friends, Wayne and Larry, for sending these ...

Pete Rogers
(San CLemente, Calif)

----- Original Message -----

From: wayne_rb@hotmail.com

Sent: 05/14/10 07:45 PM

To: Larry Bigham

Subject: Disaster unfolds slowly in the Gulf of Mexico - The Big Picture - Boston.com

Lot's of pic's

http://www.boston.com/bigpicture/2010/05/disaster_unfolds_slowly_in_the.html

5/27/2010
Page 5 of 5

____________________________________________________________________

__._,_.___

Reply to sender | Reply to group | Reply via web post | Start a New Topic
Messages in this topic (1)

RECENT ACTIVITY:
Visit Your Group

APFN-1 YahooGroups:
Subscribe: http://groups.yahoo.com/group/apfn-1/join

APFN MSG BOARD:


`In a time of universal deceit, telling the truth is a revolutionary act.'
http://disc.yourwebapps.com/Indices/149495.html

APFN LIVE TV 24/7


http://www.apfn.org/tv.htm

APFN MASTER AUDIO / VIDEO LIST:


http://www.apfn.net/videos.asp

"RADIO YOUR WAY" APFN POGO NETWORK (( WOW!! ))


"All tyranny needs to gain a foothold is for people of
good conscience to remain silent" -- Thomas Jefferson
http://www.apfn.net/POGO.HTM

Find elected officials, including the president, members of


Congress, governors, state legislators, local officials, and more.
http://congress.org/congressorg/dbq/officials/

APFN - SUPPORT / DONATIONS


PMB 206, 7549 W. CACTUS RD. #104, PEORIA, AZ 85381
http://www.apfn.org/apfn/kenvardon.htm

MARKETPLACE

Stay on top of your group activity without leaving the page you're on - Get the Yahoo! Toolbar now.

Get great advice about dogs and cats. Visit the Dog & Cat Answers Center.

Hobbies & Activities Zone: Find others who share your passions! Explore new interests.
Switch to: Text-Only, Daily Digest • Unsubscribe • Terms of Use
.

__,_._,___

5/27/2010

Você também pode gostar