Escolar Documentos
Profissional Documentos
Cultura Documentos
3 Votes
Herewith the example of command sequence in TEMS 6.1.4
Voice Call CS
i.e 120/15 means 120 second on call then call end, 15 second wait and then call again.
1. Loop Start give the number of repetition for command below the loop start (General -> Loop
Start)
2. Dial select the MS and give the destination number (Voice -> Dial)
In general cs for video call is same as voice call, but in video call in dial command we must add
v.
i.e
Loop Start
Dial v081384760975
Wait 120
End Call
Wait 15
Loop End
Packet Service (PS) Test
This is the example cs for PS test
setup account for this connection (fill username and password : orinaica and ***********)
give additional command (at command, orinaica.wordpress.com is the apn name that will use
in connection)
Source File : Select file that will get from ftp server
Target File : Destination folder where file will be place
PASV : Disable
Remote Address : IP Address of the FTP Server
Username : Username for log in to FTP Server
Password : Password for log in to FTP Server
Like this:
Like
Be the first to like this post.
Comments
1.
orinaica says:
Thanks dham
Share more ur experience in my blog ya
| Reply Posted 2 years, 1 month ago
2.
raka says:
thanx for share
oia,,
bedanya short call sama long call apaan yah??
klo bisa dijelasin yg jelas, maklum newbie, hehe
| Reply Posted 1 year, 12 months ago
orinaica says:
Short call atau sequence dalam command sequence biasanya digunakan untuk
mengecek accessibility (Call Settup Success Rate).
Contoh :
Short Call 60/10 artinya 60 second dedicated mode, dan 10 second idle mode.
Short Call 120/10 artinya 120 second dedicated mode, dan 10 second idle mode.
Long call biasanya digunakan untuk mengecek Integrity dan Retainability
(Handover Success Rate, Dropped Call Rate).
CMIIW
| Reply Posted 1 year, 11 months ago
3.
SAGSIVA says:
wow keren postingnya,,,
mw tanya nie mbk, bs ngasih contoh command sequence untuk modus short call & long
call g???skalian maksudnya klo bs??? & klo bs yg tems 8
| Reply Posted 1 year, 11 months ago
4.
dinzo says:
bro minta tolong buat bikin comand sequence buat XL untuk download data di server
publik.terimakasih.
| Reply Posted 1 year, 11 months ago
5.
hermianto says:
tanya donk!!
itu setup new connection wizard nya utk operator apa?
apa bisa utk semua operator?
thanks b4
| Reply Posted 1 year, 10 months ago
orinaica says:
6.
Noberic says:
Kalau Test *123# atau *888# bisa tidak di command sequence, kok saya coba tidak bisa
yach, jatuhnya malah nelpon. mohon pencerahannya.
trims
| Reply Posted 1 year, 2 months ago
orinaica says:
Noberic says:
Matur nuwun, Mas bisa digunakan.
Posted 1 year, 2 months ago
2. Virtual Memory
Set Virtual Memory :
Start -> Settings -> Control Panel -> System
Advance -> Performance Settings
After installition process, open Tems Investigation.
>> All Programs -> TEMS Investigation -> Data Collect
This is the example workspace for 2G (Mode Dedicated-Idle).
1. Open Worksheet Map & arrange size of window Map
2. GPS (Presentation -> Positioning -> GPS)
3. Port Configuration (Configuration -> Port Configuration)
4. Command Sequence (Control -> Command Sequence)
5. Serving + Neighbours GSM (Presentation -> GSM -> Serving + Neighbours GSM)
6. Current Channel (Presentation -> GSM -> Current Channel)
7. Event (Presentation -> Signalling -> Events)
for benchmark workspace, add Serving + Neighbours GSM and Current Channel
for MS3.
Create Geoset : Click Geoset Manager on Map window
On layer control remove all layer except Pinpoint, Cell, Event, AMR, RF Quality and
Coverage layer
2. Add layer Route, Road, MCOM Site, and other *.tab
3.
4.
5.
6.
Save Geoset
Load Cell file : Configuration -> General -> Cellfile Load
Use Cell Definition File then choose cell file
ie. Map window configured
In general cs for video call is same as voice call, but in video call in dial command
we must add v.
i.e
Loop Start
Dial v081384760975
Wait 120
End Call
Wait 15
Loop End
1. Configure Recording Properties : Menu Tab Logfile -> Recording Properties
2. Select recording folder : Click Browse -> Select Directory
3. Select Quick logging and setup size of swap file after reaching message
4. Use 2G or 3G configured workspace (with spacific map : road, route, cell file)
5. Make sure all equipments configured to the right port
6. Connect all
7. After all equipments connected (symbol green), window gps, serving neighbour
gsm, current channel and events will be full filled
8. Dont forget to lock TEMS Handset into GSM only or 3G only.
9. To start drive test, click record then start command sequence
10. After all route complete, wait untill call end then stop command sequence and
stop recording.
Here the flow step by step Go Drive Test !!!
Check logfile by playing one by one or export into MapInfo-Tab file
Open TEMS Data Collection : Start -> TEMS Products -> TEMS Investigations6.1.4
Data Collection
2. Menu Tab Logfile -> Report Generator
3. Add logfile
4. Setup Output directory
5. Setup Report properties
6. Setup IEs, Events, Mobiles, and User Details
7. Result of Report Generator in *.htm
Before post process in mapinfo, created *.tab file from logfile in TEMS :
1. Export logfile : Menu Bar Logfile -> Export Logfile
2. Click Add Order
3. Choose Format : MapInfo Tab-file
4. Setup IEs (Info Elements)
for GSM Dedicated or Idle :
- RxLev Full (dBm)
- RxLev Sub (dBm)
- RxQual Full
- RxQual Sub
- SQI
- TA
- Cell Id
- Frequency Band
- Latitude
- Longitude
for WCDMA Dedicated / Idle / Scanner :
- AS Cell Name
- AS CPICH Ec/No
- AS CPICH RSCP
- SAN CPICH Ec/No
- SAN CPICH RSCP
- SAN Cell Id (CI Part)
- Sc 1st Aggr Ec (dBm) -> Scanner
- Sc 1st Aggr EcIo (dB) -> Scanner
- Sc Best SC -> Scanner
- Latitude
- Longitude
5. Configure Options Tab
6. Save *.mex
7. Choose Logfile : Click Browse file
8. If there are more than one logfile we can merge it by Merge Output
9. Choose Output directory : Click Browse dir
10. Give Prefix : Ded if Dedicated and Idle if Idle
11. Start process, click start
12. If done, status Success
13. There were created four files for each action (*.dat, *.id, *.map, *.tab)
14. Open the exported file into MapInfo : Menu Tab File -> Open
15. Create Thematic Map : Menu Tab Map -> Create Thematic Map
16. Choose Type -> Range
17. Template Name -> Region Ranges
18. Choose Table and Field (ie. Plotting RXQUAL_SUB from Dedicated mode)
19. Customize Ranges, Style and Legend.
20. Example Dedicated by RXQUAL_SUB
EVENTS on RXQUAL_SUB
21. Create Events on RXQUAL_SUB
22. Open again the exported file (Ded_orinaica)
23. Create Thematic Map : Menu Tab Map -> Create Thematic Map
24. Choose Type -> Individual
25. Template Name -> Region IndValue Default
26. Choose Table and Field
27. Customize Style and Legend
28. Example Events on RXQUAL_SUB
SPIDER GRAPH
29. Activate spider graph : Menu Tab Tools -> Tool Manager
30. Spider Graph Load and Autoload
31. See table structure of cell in MCOM Site : Menu Tab Table -> Maintenance ->
Table Structure -> View/Modify Table choose MCOM Site
32. See table structure of CI in exported file : Manu Tab Table -> Maintenance ->
Table Structure -> View/Modify Table choose exported file (ie. Ded_orinaica) ->
Change type structure of CI
33. Click OK
34. Create Spider Graph : Tools -> Spider Graph -> Spider Graph
35. Choose Origin and Destination table
36. Save the Spider Graph table : Save Copy As -> (ie. orinaica)
37. From Spider Graph, We can analyze :
- Dominant Cells
- Overshoot Cells
- Swap Feeder
Purpose : to verify level signal each BCCH ARFCN plan
1. Setup frequency scan : Click Scan Properties
2. Select channels : Tab Scanned channels -> Manual selection -> Select
3. Setup Selected Channels (ie. BCCH ARFCN are 95-113)
4. Decode BSIC
5. Start Scanning : Click toolbar Start Scanning
6. See Scanner Bar Chart Window : Menu Bar Presentation -> GSM -> Frequency
Scanner -> Scanner Bar Chart
Purpose : Check Time Slot in each TCH (if Freq Hop : NO or Base Band)
1. Setup Channel Verification : Menu Bar Control -> GSM Channel Verification
2. Setup test phone number : Click Properties on Channel Verification window
3. Green mark means time slot have been used
Purpose : to verify damage TRX in each sector
Where is TRX ?
1. Lock BCCH ARFCN certain sector : Click Toolbar Lock on Channel (ie. Check TRX
Sector 1, Lock BCCH 111)
2. Disable Handover : Click Toolbar Disable Handover
3. See MAIO on Current Channel window
Purpose : to verify intalation mistake on feeder cable to BTS
1. Lock BCCH ARFCN each sector : Click Toolbar Lock on Channel (ie. BCCH Sect 1 =
547, Sect 2 = 540, Sect 3 = 543 )
2. Set HO Target : Equipment Properties -> Dedicated Mode -> Function -> Target
HO (ie. BCCH 547, 540, 543)