Escolar Documentos
Profissional Documentos
Cultura Documentos
INDEX
4.10 CONNECT VOICE MODULE [RP248CN DISABLE TO CONNECT WITH VOICE MODULE!!!]8
CHAPTER 2 ABOUT THE KEYPAD ......................................................................... 1
Page 1, Total 2
Function
1
Quick arm
2
Arm by code
3
Arm Stay zones
4
Arm Stay zones by code
5
System disarm
6
Duress disarm
7
Free from siren
8
Bypass zone
9
Un-bypass zone
10
Utility output
11
Set follow-me phone No.
12
Display trouble
13
Display triggered record
14
Display unready zone
15
Display zone state
16
Display memory
17
Test keypad
18
Test Stand-by battery
19
Off door chime
20
On door chime
21
Off partition door chime
22
On partition door chime
23
Off buzzer
24
On buzzer
25
Walk test
26
Set/change users code
27
Set time
28
Set date
29
Next Auto arm time
30
Next Auto disarm time
31
Auto arm
32
Auto disarm
1Power LED
2LCD Display
3Arm LED
4Disarm LED
5Bypass LED
6Fire LED
7- Tamper LED
8Digit and Function key-press
9Arm key-press
10Buzzer
11Stay Arm key-press
Procedure
[ARM]
[master code] + [ARM]
[STAY]
[ master code] + [STAY]
[user code]+[#]
[duress code]+[#]
[user code]+[#]
[*]+[1] [1]+[user code] +[#]+[zone number]
[*]+[1] [2]+[user code] +[#]+[zone number]
[*]+[2][1]
[*]+[2][7]+[ user code] +[#]+ (1-8)+[ phone No.] +[#]
[*]+[3][1] +[user code] +[#]
[*]+[3][2] +[user code] +[#]
[*]+[3][3] +[user code] +[#]
[*]+[3][4] +[user code] +[#]
[*]+[3][5] +[user code] +[#]
[*]+[4][1] +[user code] +[#]
[*]+[4][2] +[user code] +[#]
[*]+[4][3] +[user code] +[#]
[*]+[4][4] +[user code] +[#]
[*]+[4][5] +[user code] +[#]
[*]+[4][6] +[user code] +[#]
[*]+[4][7] +[user code] +[#]
[*]+[4][8] +[user code] +[#]
[*]+[4][0]
[*]+[5] +[user code] +[#]
[*]+[6]+[1] +[user code] +[#]
[*]+[6]+[2] +[user code] +[#]
[*]+[6]+[3] +[user code] +[#]
[*]+[6]+[4] +[user code] +[#]
[*]+[6]+[5] +[user code] +[#]
[*]+[6]+[6]
33
34
35
36
37
[*]+[6]+[7]
[1]+[2] at least 2 seconds
[4]+[5] at least 2 seconds
[7]+[8] at least 2 seconds
[ESC]
Trouble List
LCD Display
Trouble
MAINLOW BATT
MAINAC TROUBLE
MAINBELL LOOP
FALSE CODE P=1
KITCHENFIR
SYSTEM CLCOK
PHONE LINE
FIRE DOORDAY
Page 1
When depress [ARM] key, all the zones are armed. The LED Display delay time.
Under the user functional state, the key [ARM] is used to set data. For example, when setting the clock, [ARM]
can be used to choice the month, weekday and partition.
10. Keypad Buzzer
The buzzer is used for indicating the entry/exit delay, alarm, door chime and so on.
11. Stay Home Arming [STAY]
When depress [STAY] key, the interior zones will not be armed. During stay arming, the LCD display the
delay time.
Under user function, the [STAY] key is used to set data. For example, when setting the clock, [STAY] is used
to choice month, weekday and partition.
12. Function Key [*]
Depress [*] Key into the function set ting state.
Back t o the anterior menu or return to the normal state.
13. Confirm Key [#]
The Key [#] used for confirm and save input data.
14. Moving Key [][]
Key [] is used to choice the anterior command, or moving the cursor to left.
Key [] is used to choice the next command, or moving the cursor to right.
15. Panic Alarm Key [1][2]
Depress [1]+[2] at least 2 seconds, the system will send a panic alarm message to CMS or following-me
numbers.
16. Fire Alarm Key [4][5]
Depress [4]+[5] at least 2 seconds, the system will send a fire alarm message to CMS or following-me
numbers.
17. Special Emergency Key[7][8]
Depress [7]+[8] at least 2 seconds, the system will send a special emergency message to CMS or
following-me numbers.
CHAPTER 3 SYSTEM FUNCTION AND OPERATION
3.1 Depress Keys Audible
When depress any keys, keypad will emit a brief deep.
After any successful operation the keypad will emit a long beep to confirm. And after error operation, the
keypad will emit three brief beep warn.
When arming, the keypad(s) will beep until the end of the exit delay time.
When trigger an armed zone, the keypad will beep until end the entry delay time. The system must be
disarmed, if not, it will be triggered.
If zone(s) programmed as door chime function, when triggered the zone(s), keypad will emit three short
beeps.
When use keypad for panic alarm, fire alarm and special emergency, there will be a brief beep.
When triggered alarm, keypad will emit a beep for confirming.
It will not change the setting for siren/bell after change the buzzer setting on the keypad.
3.2 Door Chime
Each keypad can emit a continuous brief sound, called as DOOR CHIME. If you set the door chime function,
the keypad will emit a door chime sound when the door or window is opened. Turn on/off the door chime by
Page 2
&
:
4
a
b
c
d
e
5
n
o
p
q
r
6
7
8
9
0
F
S
f
s
G
T
?
g
t
H
U
.
h
u
I
V
/
i
v
J
W
(
j
w
K
X
)
k
x
L
Y
[
l
y
M
Z
]
m
z
4.
Key in a new code and confirm by depress [#]. Finish the change when LCD display ACCEPTED
5.
Depress [*] to back to anterior menu Back t o the menu or
6.
Depress [*] twice, the system will return to the normal state. Then the power LED is on, LCD display
partition, clock, date, etc..
Modifying/Setting the master Code
step
Operation
1
In disarm state, depress[*][5] to entry into function state
2
Input 4 digit master code then depress [#] to confirm, such as [1][2][3][4][#]
Input new 4 digit code then depress [#] to confirm, such as [5][6][7][8][#]
3
If successful, the keypad will emit a confirming tone Beep. The selected
4
User Code is now in effect.
Exit by depress [*][*]
5
6
Bypass zone(s).
Display troubles.
Step
1
2
4
5
Operation
In disarm state, depress [*][5] to entry into function state
Entry Master Code: such as [5][6][7][8]
Modify/set user 1 code, depress[0] [1] or
Modify/set user 2 code, depress[0] [2] or
Operation
Page 3
entry into setting follow-me number and modify state. Up to 8 of follow-me numbers can be set in the system.
Depress [][] to move cursor left and right.
When setting follow-me number(s), should select the partition number first and then input telephone number(s),
and depress [#] to confirm.
Description
Check the disarm LED indicator. If on, the system can be armed; if off,
system cant be armed, check whether every partition is ready or there is
any trouble.
Quick arm:
2
Quick arm: depress [ARM]
Quick stay arm: depress [STAY]
If operate incorrectly, the keypad will emit three short beeps, try it again
3
please
When arming, the keypad will beep until the end of exit delay time. Please
4
leave before end of exit delay. Default exit delay time is 30s.
Set time: [*]+[6]+[1]+[MASTER CODE]+[HH][MM]
Use a 24-Hour format. Hour and Minute should be two digits.
For example, if you want to entry 16:28, August 18, 2006, operate as:
[*]+[6]+[2]+[MASTER CODE]+[AUG][18][2006]
[*]+[6]+[1]+[MASTER CODE]+[16] [28]
3
4
disarm
Before end of entry delay, please input a code and [#] to disarm, or
else the system will alarm
If code incorrectly, the keypad will emit three short beep. depress
[*] and input code again.
Check keypad LCD display status:
XXXXXX DISARMED-- no alarm when armed;
XXXXALARM/ NOV 01,07 18:15 -- alarmed and the alarm
time.
Key [][] use to check other alarmed events
Arm sound
According to the default, after exit delay time, the system will make a sound to confirm the system has entered
into arm state. Cancel arm sound, please refer to chapter 6 section 6.5.2
3.9 Disarm and disarm sound
Disarm system
RP248CN can set several groups of 4 digits or 6 digits code in advance, one of them is master code, and
others for users. All of the code can disarm system.
Disarm sound
As the default, RP248CN will emit a long beep to confirm disarm successfully. Input [*]+[4]+ [7] or [8 ] +
[master code] can turn on or off the disarm sound
3.10 Duress code disarm
When be forced, suggest user using duress code to disarm the system. Disarm system through duress code it
will report a duress message to the alarm centry to for help without any siren or buzzer on.
Any disarm code (master code and users code) add 1 to the last digit is to be duress code. Such as: if the
disarm code is 1234, then the duress code will to be 1235. if code is 7890, then the forced code is 7891.
3.11 Stop siren/bell and stop dialing a number
When entry, the below display on the keypad means alarmed event:
Page 4
Key [] [] are used to check each zone status. Depress [*] or wait few seconds, the system will auto return
to normal status.
Bypass zone(s)
In normal, input a correct user code and depress []. If quick bypass is allowed, depress [] to bypass this
zone directly. LCD displaying as follows:
BYPASS ZONE (CL)
01 ZONE 01
N
The first line means the zone status, second line means whether the zone is bypassed or not. Use key [] to
choice other zone(s), use key [STAY] to exchange [Y] and [N], and depress [#] to confirm.
LCD Display
Battery Power low
AC lost
Siren trouble
Code error
KITCHENFIR
SYSTEM CLCOK
MAINAUX TRBL
For disarmed system: CL-means zone(s) is closed, OP-means zone(s) is triggered.
For armed system: AR- means zone(s) is armed, CL-means zone(s) is not triggered but bypassed, OP- means
zone(s) is triggered but bypassed, AA- means zone(s) armed.
Cancel bypass
Choose a zone number, use [STAY] exchange Y to N, and depress [#]
Bypass reset
Under user function state, use key [][] to choose 2)BYPASS RECALL, and depress [#] to confirm. Input a
correct user/master code and [#] If quick arm is allowed, need not input code). LCD will display as follows,
depress [#] to confirm bypass reset:
BYPASS RECALL
HIT [#] TO CONFIRM
Exit user function state
Depress [*] two times, exit user function state. In normal, the power LED indicator will turn on.
3.13 Exit a error operation
When operate incorrectly, depress [*] to cancel and then operate again.
3.14 Keypad alarm
RP248CNs keypad (RP248KCL) has 3 groups of emergency buttons for reporting intrude alarm, fire alarm or
medical alarm. All of the emergency alarm is silence alarm in default.
Depress [1] and [2] together at least 2 seconds for intrude alarm.
Depress [5] and [6] together at least 2 seconds for fire alarm.
Depress [7] and [8] together at least 2 seconds for medical alarm.
Trouble
MAINLOW BATT
MAINAC TROUBLE
MAINBELL LOOP
FALSE CODE P=1
PHONE LINE
FIRE DOORDAY
Page 5
2.
3.
4.
5.
Depress [ARM];
Select the partition to be armed by [][];
Depress [ARM] or [STAY]. If there is exit delay, the partition will entry into exit delay countdown;
Repeat steps 1-4 to arm other partitions
steps is as follows:
Page 6
Page 7
Please connect the 4 lines of the keypad with the main board respectively according to the red, black, yellow
and green sequence. Such as Fig.2 shows.
When more than one Keypad is to be connected, please make all the keypads as parallel connection. Set a
individual code for each Keypad by the dial switch on it and programming the control panel.
4.5 Connect the Telephone Line
There are two group ports of telephone lines on the main board. The ports which mark SET used for input,
SET for telephone. Such as Fig.2 shows.
4.6 Connect the Standby Battery
Please provide a standby battery (DC12V) inside to panel in case of the AC power is cut off. Two lines marked
BAT link the battery with anode+ (red) and the cathode - (black) respectively. Such as Fig.2 shows.
Don't conjunction any power before connected all the lines well.
Fig.4 R
emote Receiver
You can communicate your RP248CN (8-72 zones control panel) through LCD Keypads (RP248KCL). Each
RP248CN can match with 16 LCD keypads at most. With the LCD Keypad(s), you can operate your system by
arm/disarm, bypass, emergency, closing the siren, inspecting trouble, programming the system and so on. The
system status can be displayed by the LCD or/and indicator light.
All of your systems detectors are wired to the control panel. As such, your system always knows the status of
any protected door, window, hallway, room, or area.
Page 8
RP248CN
5.1 Features of RP248KCL
Tamper is supervised
Quick arm
Expansion Modules
There are four expansion modules can match with RP248CN: 8 Zones Expansion Module (RP248EZ8), 8
Zones Wireless Expansion Module (RP248EW8), 16 Zones Expansion Module (RP248EZ16) and 16 Zones
Wireless Expansion Module (RP248EW16).
7/10/13/16/19/22/25/28COM the port of common earth, which should be connected to one port of
ALARM or TEMPER on the detector(s).
Page 9
7- Tamper port of the module, which can make up a loop with the port of BLK
8/9- BELL+ is to be connected with anode of the siren, BELL- is to be connected with the cathode of the
siren.
10- Connect to earth
11/12- AC supply input (AC16.5V)
13- Power LED indicator
14- Dial switch.
Clock
Monitor Function
Trouble data can be displayed on LCD Keypad, and also can be transmitted to central station
Battery in low power
Siren loop in trouble
AC supply in trouble
System clock is not set
Tamper prevention
Fire alarm loop trouble
Page 10
Page 11
[1][5]
S.AUX Break
10 seconds
[1][6]
WL MOD. TIMES
[1][6] [1]
JAMMING TIME
none
Specify
wireless
module
can
withstand
wireless
power
frequency , the time of signal send
by interference system emitter.
If set, main board will send a report
code to alarm center once reach the
set time.
If hear the interference = yes, main
board also will start-up the sound
box which set at outside.
NONE means system not only do not
inspect , but also will not send any
signal for the interference signal
which have inspected
0 hour
Display
Default
[1]
[1][1]
TIME DEFINE
EX/EN Delay 1
[1][1][1]
Entry Delay 1
30 seconds
[1][1][2]
Exit Delay 1
45 seconds
[1][2]
EX/EN Delay 2
[1][2][1]
Entry Delay 2
45 seconds
[1][2][2]
Exit Delay 2
60 seconds
[1][3]
Bell Timeout
4 minutes
[1][4]
Bell Delay
[1][6] [2]
S.V. TIME
[1][7]
Z.TEST TIMES
[1][7][1]
Start
[1][7][2]
Z.TEST.PERIOD
[2]
SYSTEM CONTROL
[2][0][1]
Quick Arm
Explanation
Set delay time
Exit/Entry delay 1
Entry delay 1, range:
0-225s
Exit Delay 1, range:
0-225s
Exit/Entry delay 2
Entry delay 2, range:
0-225 s
Exit delay 2, range:
0-225 s
Bell time out, range:
01-90 minutes
Bell delay time , range:
00-90 Minutes
test at
00
YES
Page 12
[2][0][2]
Quick UO
YES
[2][0][3]
Allow BYPS
YES
[2][0][4]
Quick BYPS
NO
[2][0][5]
FLS CD TRB
YES
[2][0][6]
Bell SQK
YES
[2][0][7]
Bell 30/10
NO
[2][0][8]
Alarm PH Cut
NO
[2][0][9]
[2][1][0]
3-MIN BYPAS
D. VER FIRE
YES
NO
Quick UO output:
YES: UO can be triggered without
code
NO: UO should be triggered by code
Bypass zones:
YES: Bypass the zone is allowed
NO: Bypass the zone is not allowed
Quick Bypass:
YES: Bypass the zone without code
NO: should enter a code to bypass a
zone
False code trouble:
YES: report to the central station after
enter false code thrice;
NO: the alarm will be activated after
enter false code thrice.
Bell squawk:
YES: the bell will emit a brief beep
after the exit delay
NO: the bell will keep silent after the
exit delay
Bell alarm function:
YES: the sound will pause 10
seconds after the bell sounds 30
seconds
NO: no pause when the bell is
sounding
Alarm phone cut:
YES: the bell will alarm when the
phone line is cut off
NO: the bell will keep silent when
the phone line is cut off
3- minutes bypass:
YES: the zone will be bypassed for
3-minutes automatically after power
the system
NO: hasnt this function
Conform fire alarms:
YES: for smoke Detectors:
1.Smoke detectors have been
triggered
2.The power of the detectors have
been cut off with 15 seconds
3.Power the detectors
4.The system will alarm when the
detectors are triggered again in 1
minute
NO: No confirm fire alarms
[2][1][1]
Audible AUD
NO
AC REP DLY
NO
[2][1][3]
BUZZBell
NO
[2][1][4]
ALE ZE Cut
NO
[2][1][5]
FIRE TMP
NO
[2][1][6]
CODE GM
NO
[2][1][2]
[2][1][7]
AUDI JAMM
NO
Audible panic:
YES: the emergency Keys will drive
the exterior siren or bell
NO: silence
AC trouble report delay:
YES: a report will be sent to the
central station after the AC in trouble
for 30 minutes
NO: a report will be sent to the central
station as soon as the AC in trouble
Buzzer/bell:
YES: stay armed system, the buzzer
will sound 15 seconds firstly before
the bell sound when the system
alarm.
NO: stay armed system, the buzzer
and bell will sound at the same time
when the system alarm.
Alarm zone expansion module cut:
YES: the system will be triggered
when the communication between
zone expansion module and
mainboard has been cut
NO: the system will have trouble
when the communication between
zone expansion module and
mainboard has been cut
Fire Temporal Pattern:
YES: when fire alarm, the bell will
has a pause after sounding three
times;
NO: When fire alarm, the bell will
pause 2 seconds after sounding 2
seconds.
Code Grand Master:
YES: Change the users code by only
master code;
NO: Except the master code, users
can change code in same or lower
grade code
the parameter about the interference
time ,please see shortcut key (1) (1)
(6) (1)
YES: once reach the set time ,main
board will start up the outside sound
box ,and send report code to alarm
center.
NO: except the outside sound box do
not ring ,others will same as above.
Page 13
[2][1][8]
TECH TAMPR
NO
[2][1][9]
TECH RESET
NO
[2][2][0]
ABORT ALARM
NO
[2][2][1]
SUMM/WINT
NO
[2][2][2]
FORCED KSW
YES
[2][2][3]
PAGER
NO
[2][2][4]
ARM PREWRN
NO
[2][2][5]
L.BATT.ARM
YES
[2][2][6]
ENG.TAMPER
NO
ready)zone recovery.
When the specify event happed in
parts, user could receive inform
signal parameter via letter and
number mini BP machine. First , on
the user operation function , as a
Follow-Me
(follow
telephone)
setting, must programme number of
the BP machine.
YES: allow via number or letter
number BP machine, provide
increased event information ,once
the call will through ,will send and
show.
NO: only during the parts alarm
station ,call the BP machine. Need as
Follow-me programme, can not
increase the standard information by
send
YES: when any parts set as arm
automatically, 225seconds before
arm automatically, will hear exit
delay
(pre-alarm)
counter
backwards second.
During this period, the parts as
programmed as above, distributed
keypad ,will hear the exit delay DIDI
sound.
During the any time of the counter
backwards second, if input the
efficiency user code, automatically
arm of the parts will delay 45
minutes.
If
parts
have
already
arm
automatically, will disarmed after
input the efficiency user code. Will
can not arm automatically that day.
Arm delay 225 second ,do not adapt
arm automatically.
NO: Any parts , arm automatically
will happen on the set time
Programme exit delay time and all
hearable pre-alarm
YES: allow system arm when spare
battery have low pressure
NO: not allow system arm when spare
battery have low preesure.
YES: after tamper alarmed, system
will not ready arm ,and TAMPER
Page 14
[2][2][7]
BLANK DISP
[2][2][8]
24H BYPASS
[3]
SET CLOCK
[3][1]
System D ATE
[3][2]
System Time
NO
NO
JAN 01 2000
00:00
WINDOWING
[4][1]
Window Start
H:00
M:00
[4][2]
Window Stop
H:00
M:00
[4][3]
Window Days
ALL
SYSTEM LABEL
[5][0]
Global
[5][1][5][8]
Partitions 1 thru 8
[6]
[7]
[8]
TAMPER SOUND
DFLT EN/DIS
SERV. NAME
ORBIT
SECURITY
[8] [2]
SERV. PHONE
SYSTEM
[4]
[5]
[8] [1]
ONE-BY
-ONE
---
Note: after you finish all zones, depress [#]. The keypad will emits a
long beep--, the data will be saved.
All the
Zones
belong
to one
Partition
[2]
PARTITI
ONS
[3]
ZONE
TYPE
[3][0][
0]
[3][0][
1]
[3][0][
2]
NOT
USED
EX/EN 1 Zone 1
Exit/Entry delay 1
EX/EN 2
Exit/Entry delay 2
[3][0][
3]
EX(OP)/
EN
If the zone is bypass during the exit delays, even if the zone is opened,
the system still can be armed
[3][0][
4]
EN
FOLLO
W
Zone 2
There are two zones have Exit Delay, Exit Delay 1 and Exit Delay 2. If
zone with Exit Delay 2 has been triggered before zone with Exit Delay 1.
The zone with Exit Delay 1 must have entry delay. Otherwise, the system
will alarm immediately.
[3][0][
5]
Instant
The
zones
except
zone1
System mark
SERVICE INFO
[1]
First, program set all the data to the zone 1: zone type, sound, terminal
features, loop response, labels, and so on. Then program other zones
one by one.
Page 15
and
zone2
[3][0][
6]
[3][
0][7
]
[3][
0][8
]
[3][2]
[1]
I+
EX/EN 1
I+
EX/EN 2
[3][1]
[0]
I+
EX(OP)/
EN
I+EN
FOLLO
W
I+INST
ANT
[3][1]
[1]
UO
Trigger
Day
When the system is triggered, It will alarm at the armed state and
report trouble at the disarmed state
[3][0][
9]
[3][
1][2
]
[3][1]
[3]
[3][
1][4
]
[3][1]
[5]
[3][1]
[6]
[3][1]
[7]
[3][1]
[8]
[3][1]
[9]
[3][2]
[0]
Fire
Armed, It will alarm when the short the port; Disarmed, it will report
trouble when open the port
LATCH
KSW
EN.FO
LL+ST
AY
[4][1]
[4][2]
[4][
3]
[4][4]
Medica
l zone
Key
Switch
EXIT
TERM
[
4
]
24
Hours
Panic
[3][2]
[2]
[4][
5]
[
5
]
[5][
1]
When system keep STAY arm , zone will same as enter/exit extend
time zone, extended time for enter and exit , will specify by enter/ exit
extend 1.
When system keep AWAY arm , zone will same as: enter into
linkage ,will produce instant in break alarm when there is in break in
zone.
If there have already have one exit/enter extend time zone was
inbreak, enter into linkage+ stay arm zone, will keep bypass ,until into
extend time close.
[6][
2]
[6][3]
[7]
TERMIN
ATION
N/C
Normal closed
DEOL
[6][1]
Door
Chime
[5][3]
[6]
The same as zone type 19, but have the specify time for exit/enter
extend time 1.
Silent
Alarm
Bell
All
Only
Zones
Buzzer
Only
Bell+Buz
zer
EOL
[5][4]
The same as zone type 17, but have the specify time for exit/enter
extend time 1.
Zone
Sound
[5][2]
KEY
SW
DLY
LTCH
KSW
DLY
N
/
O
LOOP
RESP
ONS
E
N
o
r
m
a
l
L
o
n
g
Fast
Cross
zones
All
Zones
YES
500 ms
1 sec
10 ms
When two zones are defined as cross zone, they must be triggered at
certain interval time the alarm will be happen.
Page 16
[7][
2]
[7][3]
[8]
[9]
[9][
1]
[9][2]
[9][3]
[9][4]
[9][5]
N
O
N
E
ORDE
RED
NOT
ORD
ERED
Time
Slot
L
a
b
e
l
s
MAINTE
NANCE
Copy a
Zone
Delete
a Zone
Add/Cop
y
Partition
Delete
Partition
WL
ZONE
ALLOC
YES
No cross zone
YES:
monitor
, NO:
un-mo
nitor
ZONE01
ZONE02 Edit the zone labels
Etc.
Maintenance
Copy the zones data, including type, terminal, loop response, partition
and alarm sound
Delete a zone and restore it to default, then the zone type is unused
[9][6]
[9][5]
WL
COMM
TEST
Press [ENTER]
If the following is displayed on screen,
ZONE=09 (ALLOC):1)
SKIP
Then press [ENTER] to skip it and come to the allocation of next
transmitter
Wireless
Commu
nication
Test, ex:
ZONE09
000%
0.37%
the
referring
date is
12%
press [ENTER]
Use [STAT] and [BYP] to move cursor and select zone number,
Note: Zone 1 to Zone 8 are reserved for the wired zones
ZONE ALLOCAT:
ZONE#=09 (1:01)
XX+E
NTER
ZONE=09 (ALLOC):
4) SUPERVISION
Choose YES/NO, then press [ENTER]
ZONE ALLOCAT:
ZONE#=09 (1:01)
[9][7]
SELFT
EST
ZONE
S
Page 17
7)
Set the interval time(01-24 hours) for testing, and then press
[ENTER]
8)
Press [*] to exit
Set Universal Output to trigger the noises source
6)
Press [ENTER]
ZONE TEST PERIOD
PERIOD: 00 (00-24)
3)
Input the first two digits zone number; if necessary, use the
[BPY]or [STAT] to move the cursor, then press[ENTER]; press
[ENTER] again to repeat the above operations and select the
next zone; keep on this operation until all the zones are selected
and make sure all the zones number are inputted correctly; then
press[*] to end the operation.
Time setting is in : 1) SYSTEM
Zone time testing
TIME DEFINES:
7) Z. TEST TIMES
1)
2)
Press [ENTER] again
START TEST AT:
HOUR: 00
MIN: 00
3)
Set the first testing time (24 hours form) at this step; then
use[BPY] or [STAT] to move the cursor properly
4)
Press [ENTER] to keep on
5)
Press [SYP] one time to keep on
ZONE TEST TIMES
2) Z. TEST PERIOD
4)
At this display, press [1] to select the system
UO=02
FOLLOWS:
1) SYSTEM
i.
Press [ENTER]
SYS.EVENT: UO=02
1) BELL
FOLLOW
ii.
iii.
Press [ENTER]
PATTERN UO=01:
2) PULSE
N/O
iv.
Page 18
Output
Def
ault
Yes
Instruction
[0]
[1]
[1][1]
[1][1][1]
[1][1][2]
Nothing
System
Event
BELL FOLLOW
NO TEL. LINE
[1][1][3]
COMM. FAIL
[1][1][4]
TROUBLE FOLL
[1][1][5]
GND PULSE
[1][1][6]
LOW BAT.FOLL
[1][1][7]
AC LOSS FOLL
[1][1][8]
SENSORS TEST
[1][1][9]
VOICE MODULE
[1][1][0]
BATTERY TEST
[1][2]
PARTITION
[1][2][1]
Pulse N/C
[1][2][2]
Latch N/C
[1][2][3]
Pulse N/O
[1][2][4]
Latch N/O
[2]
PARTITION
[2][1]
Event
READY
Follow(Latched)
[2][1][0][1]
[2][1][0][2]
[2][1][0][3]
[2][1][0][4]
[2][1][0][5]
ALARM
[2][1][0][9]
Buzzer Follow
[2][1][1][0]
CHIME FOLLOW
[2][1][1][1]
Entry/Exit Follow
[2][1][1][2]
[2][1][1][3]
Daytime Zone
Trouble
[2][1][1][4]
Trouble Follow
[2][1][15]
STAY FOLLOW
[2][1][16]
TAMPER FOLLOW
[2][2]
Mode
[2][2][1]
Pulse N/C
[2][2][2]
Latched N/C
[2][2][3]
Pulse N/O
[2][2][4]
Latched N/O
[3]
Zone
[3][1]
Zone Follow
[3][1][1]
Pulse N/C
[3][1][2]
Latched N/C
[3][1][3]
Pulse N/O
[3][1][4]
Latched N/O
[3][2]
Alarm Follow
[3][3]
Arm Follow
[2][1][0][7]
Panic Follow
(Latched)
Special Emergency
Follow (Latched)
Duress Code
Follow(Latched)
[2][1][0][6]
Follow
Arm Follow
(Latched)
BURGLARY FOL
(Latched)
Fire Follow
(Latched)
[2][1][0][8]
[4]
Code
[4][0][0]
Master Code
Page 19
[4][X][x]
User Code
User code01-30
User code trigger
[1]
6.5.5 Code Maintenance
Code
Hot Key
Maintenance
Default
Instruction
[1]
Administer
[2]
PARTITION
[3]
GRAND CODE
1234
[4]
INSTALLER
0248
[5]
SUB INSTALLER
0299
[6]
CODE LENGTH
[6][1]
4 Digit
[6][2]
6 Digit
Dial
Hot Key
[1][1]
[1][2]
[1][3]
[1][4]
Defaul
t
Phone Number
Monitor Station Phone
Number 1
Monitor Station Phone
Number 2
Monitor Station Phone
Number 3
Remote Control
Station Phone Number
[2]
User Accounts
[2][X]
Division Number
Number
[3]
Communication Format
[3][1]
Monitoring Station 1
0000
[3][2]
Monitoring Station 2
0000
[3][3]
Monitoring Station 3
0000
[4]
[4][1]
Access Code
5678
[4][2]
Identify Code
0001
[4][3]
MS.LOCK
[5]
Control
Dial control
[5][0][1]
MS ENABLE
Yes
[5][0][2]
FM ENABLE
Yes
[5][0][3]
U/D ENABLE
Yes
[5][0][4]
Call Delay
Yes
[5][0][5]
DIAL TONE
Yes
[5][0][6]
Call Save
No
Yes
Instruction
000000
Page 20
[5][0][7]
USER INIT
Yes
[5][0][8]
CALLBK U/D
Yes
[5][0][9]
AUTO BATCH
No
[5][1][0]
ANS MACHIN
Yes
[5][1][1]
UL INSTAL
No
[5][1][2]
SHOW KISOF
No
[5][1][3]
[5][1][4]
SHOW HNDSH
AUDIBLE KO
No
NO
[6]
[6][1]
ParameterS
MS RETRIES
8
Dial parameter
Re-dial times of center station
communication failure01-15
Default 8 times
[6][1][1]
01-15
[6][2]
Fm RETRIES
3
[6][2][1]
01-15
[6][3]
RINGS TO U/D
12
default 12 times
[6][3][1]
01-15
[6][4]
DIALTON TIME
Yes
[6][4][1]
WAIT 6 SEC
[6][4][2]
WAIT 9 SEC
[6][5]
REDIAL WAIT
[6][5][1]
Wait 30 seconds
[6][5][2]
Wait 60seconds
[6][6]
DIAL METHOD
[6][6][1]
[6][6][2]
DTMF
Impulse, 20BPS
[6][6][3]
Impulse, 10BPS
[6][7]
[6][7][1]
[6][7][2]
67%/33%
61%/39%
[7]
[7][1]
[7][1][1]
[7][1][2]
REPORT SPLIT
MS Arm/Disarm
DO NOT CALL
CALL 1ST
[7][1][3]
CALL 2ND
[7][1][4]
[7][1][5]
CALL 3RD
CALL ALL
Default 30 seconds
[7][2]
MS URGENT
Yes
Option 1-6
[7][3]
MS NON URGENT
[7][4]
[7][4][1]
Option 1-6
FOLLOW ME
DO NOT CALL
[7][4][2]
BY PARTITION
[7][4][3]
[8]
[8][1]
[8][2]
[8][3]
[9]
CALL ALL
Alarm Restore
Bell Ending Report
Follow Zone
Disarm Report
Test
[9][1]
MS Test
[9][2]
UD Test
Yes
Yes
EMERGENCY Key
Alarm
SPECIAL
PANIC
Fire
DURESS
Restore
SPECIAL
PANIC
Fire
DURESS
[4][2]
[4][2][1]
[4][3][2]
[4][3][3]
[4][3][4]
[4][3][5]
[4][3][6]
[4][3][7]
[4][3][8]
[5]
[5][1]
Trouble restore
Low battery
Bell
phone
AC
Aux
Clock IS set
Bus COM
FALSE code
PS ACCS trbl
Trouble
[2]
[2][1][X]
Zone
Alarm
[5][1][1]
[5][1][2]
Low battery
Bell
[2][2][X]
[2][3][X]
Restore
Trouble
[5][1][3]
[5][1][4]
AC LOSS
Auxi fail
[2][4][X]
[2][5][X]
Trbl Restore
Bypass
[5][2]
[5][2][1]
restore
Low battery
Default is DTMF
Yes
Europe
USA- default
[7][1][6]
Page 21
[2][6][X]
[2][7][X]
[2][8][X]
[2][9][X]
[3]
[3][1]
[3][1][1]
[3][1][2]
[3][2]
[3][2][1]
TAMPER
TAMPER REST
LOW BATTERY
LOW BAT RST
ACCS Tamper
Keypad
Tamper
Tamper Restore
UTIL OUTPUT
Tamper
[5][2][2]
[5][2][3]
[5][2][4]
[6]
[6][1]
[6][2]
[6][3]
[6][4]
[6][5]
[6][6]
Bell
AC
Aux
Arm
User arm
KEYsw arm
Anto arm
Remote arm
Quick arm
Force arm
[1][1]
[3][2][2]
[3][3]
[3][3][1]
[3][3][2]
Tamper Restr
Power Supply
Tamper
Tamper Restore
[1][3]
[3][4]
[3][4][1]
[3][4][2]
[3][5]
EVENT LOGGER
Tamper
Tamper Restore
WL BUTTON ACC
[3][5][1]
[3][5][2]
[3][6]
Tamper
Tamper Restore
ZONE EXPANDER
WL BUTTON ARM
Disarm
User disarm
KEYSW disarm
Auto disarm
Rmt disarm
WL BUTT ARM
MISCELLANEOUS
Entry progr
Exit prgram
Period MS test
Period UD test
CALL BACK
SYSTEM RESET
Abort alarm
Self test ok
Self tst fail
Cancel report
Special
Accessor code
Wireless ze
[3][6][1]
[3][6][2]
[4]
[4][1]
Tamper
Tamper Restore
MAIN TRBL
Trouble
[4][1][1]
[4][1][2]
Low Battery
Bell
[6][7]
[7]
[7][1]
[7][2]
[7][3]
[7][4]
[7][5]
[8]
[8][1]
[8][2]
[8][3]
[8][4]
[8][5]
[8][6]
[8][7]
[8][8]
[8][9]
[8][0]
[9]
[0]
[0][1]
[4][1][3]
phone
[0][1][1]
Jamming trbl
[4][1][4]
AC LOSS
[0][1][2]
[4][1][5]
[4][1][6]
[4][1][7]
Aux Fail
Clock NOT set
Bus FAIL
[0][2]
[0][2][1]
[0][2][2]
[0][3]
[0][3][1]
[0][3][2]
[0][3][3]
[0][3][4]
Wl butt mod
Jamming trbl
Jamm tr. rstr
Printer modul
Prn trouble
Prn trbl rstr
Prn buff full
Prn buff rstr
Add/Del Module
Add/Del Module
[1][2]
[1][4]
[1][5]
[1][6]
[1][7]
[2]
Keypad
Add keypad
None
None
LCD
Add RP248KCL
Zone Expander
None
ZE08
ZE16
Utility Output
None
UO04
Power Supply
None
PSO1
event
Wl button mod
Printer modul
Verity Module
[3]
Bus Test
[4]
Bus Scanning
8) MISCELLANEOUS
Hot Key
MISCELLANEOUS
[1]
WL BUTT ALLOC
Instruction
Page 22
Zone Alarm/Disarm
BUTT=01 (EMPTY):
2) (RE) WRITE
(PPS)
Kiss off/
Pulses/se
Handshake
c
10
1400Hz
Dual Round
Inter
Digit
Time
650
Validation
Code
Format
0F
10
1400Hz
Dual Round
650
4F
10
20
20
2300Hz
1400Hz
1400Hz
Dual Round
Dual Round
Dual Round
650
650
650
17
0E
4E
20
2300Hz
Dual Round
650
56
20
20
20
20
20
40
40
40
40
40
40
40
2300Hz
1400Hz
2300Hz
1400Hz
2300Hz
1400Hz
2300Hz
1400Hz
2300Hz
1400Hz
2300Hz
1400Hz
Dual Round
Dual Round
Dual Round
Dual Round
Dual Round
Dual Round
Dual Round
Dual Round
Dual Round
Parity
Parity
Parity
390
390
390
390
390
390
390
390
390
390
390
390
12
02
12
42
52
00
10
40
50
20
30
60
40
2300Hz
Parity
390
70
(4+3+parity)
03B1
(Contact)ID
(DTMF ,parity)
0420
(4+2+parity)
0520
Entry/Exit Alarm
Entry/Exit Restore
Panic Alarm
Panic Restore
24 Hours Zone Alarm
24 Hours Zone Restore
Tamper Zone Alarm
Tamper Zone Restore
Smoke Zone Alarm/Restore
Fire Zone Alarm/Restore
Waterproof Zone Alarm/Restore
High Temperature Zone Alarm
High Temperature Zone Restore
Pipeline Zone Alarm/Restore
Fire Zone Alarm/Restore
Warning Sound Alarm
Warning Sign Alarm
Perimeter Zone Alarm/Restore
Interior Zone Alarm/Restore
Daytime/Night Zone Alarm/Restore
Open Zone Alarm/Restore
System Zone Alarm/Restore
Detector Tamper Zone Alarm/Restore
24 Hours Zone Alarm/Restore
Gas-fired Alarm
Gas-fired Restore
Low Temperature zone
Alarm/Restore
Temperature Dissipate
Alarm/Restore
Liquid Leak Alarm
Liquid Leak Restore
Oil Leak Alarm/Restore
Gas Leak Alarm/Restore
High Temperature Alarm/Restore
Temperature Dissipate
Alarm/Restore
Airflow Unsteady Alarm
Special Function
Urgency Key-depress Alarm
Urgency Key-depress Restore
Fire Zone Alarm
Fire Zone Restore
Fire Key-depress Alarm
Report
Code
134
134
130
130
133
133
137
137
111
112
113
114
114
116
117
122
123
131
132
135
136
140
144
151
151
151
152
153
154
154
155
157
158
159
161
100
100
110
110
115
Page 23
2.4
INITIATE CALL
121
121
2.5
HAND OVER
2.6
2.7
FM PHONES
2.8
ENABLE U/D
2.9
2.0
CANCEL
REPORT
3.1
TROUBLE
301
301
302
302
321
321
373
373
On/Off Reporting
User Arm
User Unarm
User 0 Quick Arm/Disarm
Force Arm
Periodic Test
USER FUNCTIONS
Hot Key
115
120
120
6A
6A
62
63
64
Display
401
401
408
574
602
Explanation
1. BYPASS
1.1
BYPASS ZONES
1.2
BYPASS RESET
1.3
BYPASS
RECALL
UTIL OUTPUT
3.VIEW
2. ACTIVITIES
2.1
2.2
SWITCH AUX
2.3
TERMINATE FM
3.2
3.3
3.4
3.5
3.6
ALARM
MEMORY
NOT
READY
Allows the viewing of all "not ready" zones.
STA
Allows the display of all system zones and their
ZONE STATUS
current status.
Allows the viewing of significant system events
EVENT LOG
including date and time
SERVICE INFO
Page 24
3.7
OVERVIEW
4.MAINTENANCE
KEYPAD TEST
4.2
BATTERY TEST
4.3
4.5
6.6
6.7
VACATION
6.7.1
PARTITION
7.INSTALLER
4.1
4.4
6.5
LCL CHIM ON
4.6
PAR CHIM ON
4.7
4.8
LCL BUZZ ON
4.0
WALK TEST
5.ACCESS CODE
8.ACCESS CNTRL
8.1
OPEN DOOR
8.1.1-8.1.8 DOOR No 1 - 8
8.2
CUSTOM MSG
8.2.1-8.2.8 UNIT No 1 - 8
9.MISCELLANEOUS
9.1
PRINTER
CNTRL
9.2
ANTI-CODE
9.3
DURESS
RESTOR
6.CLOCKS
6.1
SYSTEM TIME
6.2
SYSTEM DATE
6.3
NEXT ARM
6.4
NEXT DISARM
Page 25