Você está na página 1de 275

PAPER - II

PART I
1. Which statement is correct?
a) Al-alloy bolt smaller than mm diameter are not used in primary
structure
b) Al-alloy bolts and nuts are used where they will be repeatedly
removed for purpose of maintenance and inspection
c) Both are correct
d) None of these
2. AN-73 drilled head bolt is similar to the
a) Close tolerance bolt
b) Special bolt
c) Standard hex-bolt
d) All of these
3. To-bolt is a trade name of
a) An internally treaded two piece rivet
b) An externally treaded three piece rivet.
c) An internally treaded three piece rivet
d) An externally treaded two piece rivet
4. During installation of To-bolt
a) The nut is turned while the bolt is held
b) The bolt is turned while the nut is held.
c) Bolt are turned at the same time
5. The lock bolt combines the features of a
a) High strength bolt and nut
and rivit
c) High strength bolt, rivet and nut

d) None of these
b) High strength bolt
d) None of these

6. Blind type lock bolts are


a) Used where only one side of the work is accessible
b) As a) & they have exceptional strength
c) As b) & sheet pull together characteristic
d) As c) & where it is difficult to drive a conventional rivet
7. How is a clevis bolt used with a fork-end cable terminal recurred?
a) With a shear nut tightened to a snug fit with no strain imposed on
the fork and safetied with a cotter pin.
b) With a castle nut tightened until slight binding occurs between the
fork and the fitting to which it is being attached.
c) With a shear nut and cotter pin or a thin self-locking nut tightened
enough to prevent rotation of the bolt in the fork

d) None of these

8. Which of the bolt head code marking shown identifies a internal


hex head bolt?
a)
b)
c)

1) a

2) b

3) c

4) none

9. Which statement is correct?


a) Self-locking nuts are used on a/c to provide tight connections which
will not shake loose under severe vibration
b) S.L.N are used where bolt or nut subject rotation
c) Both a) & b)
d) None of these
10. Elastic stop nuts are not used
a) Where temperature is lower than 250oF
c) Between 250oF to 750oF

b) Higher than 250oF


d) None of these

11. Special washers are used


a) Where a bolt is installed at an angle to a surface
b) Where perfect alignment with a surface is not required
c) Both a) & b)
d) None of these
12. The marking found on the head of the stud
a) Body diameter, length & shank type
b) Body diameter, length & head type
c) Only length
d) None of these
13. Airloc pasteners consists of three parts
a) Stud, grommet and receptacle
grommet
c) Stud, cross pin and receptacle
14. 7x19 cable is made up
a) Seven strands of 7 wires
seven wires each

b) Stud &
d) None
b) Nineteen strands of

c) Seven strands of nineteen wires each


d) 19 strands of 19 wires each
15. The diameter range of 7x19 cables are
a) 1/8 to 3/8
b) 1/16 to 3/32
c) 1/8 to
d) 1/8 to 1/16
16. Turnbuckle assembly is a
a) Mechanical screw
b) Making minor adjustment in cable length and adjusting cable
tension
c) Consisting two threaded terminals and a threaded barrel
d) All the above

17. Push-pull tubes are generally made in short lengths to


a) Prevent vibration and bending under tension load
b) Prevent vibration and bending under compression load
c) Only prevent vibration
d) None
18. Corrosion resistant steel cotter pin is used in locations where
a) Magnetic material is required
b) Resistance to
corrosion is desired
c) Both
d) None
19. Which is correct statement
a) Pin rivet are used only in shear application
b) They should never be used where the grip length is less than the
shank diameter
c) Both
d) None
20. Pin rivets
a) Hi-shear rivets
b) Used where access to both side of the material is required
c) They are approximately three times as strong as solid shank
rivets
d) All
21. 10 KB 105
a) Flat head

b) Flat head & countersunk

c) Countersunk
22. 10 KB 107
a) Closed end and a key
c) As a and countersunk head
23. AN 10 DH5A where H indicate
a) 5/8 diameter head drilled
and shank drilled
c) 5/8 diameter & shank drilled

d) None
b) Flat head
d) None
b) 5/8 diameter head
d) None

24. O-rings can be detected by


a) 4 power magnifying glass
b) Small cracks, particles of foreign material or other
irregularities are checked by rolling
c) Slight stretching of the ring checked by dowel
d) All
25. Clevis bolt are used for
a) Tension load
c) Shear load

b) Tension & shear load


d) None

26. Internal wrenching bolts are suitable for use in


a) Shear load
b) Tension & shear load
c) Tension
d) None
27. A cross inside triangle indicates
a) Close tolerance bolt
steel bolt
c) Stainless steel bolt

b) Corrosion resistant
d) Screw

28. A/C screw is generally manufactured with


a) Class-1 fit of thread
b) Class-2 fit of thread
c) Class-3 fit of thread
d) Class-4 fit of thread
29. Generally speaking, bolt grip length should be
a) 1 time the thicker material through which they extend
b) Equal to thickness of material + one diameter
c) Equal to thickness of material through which they extend
d) Any length
30. Stainless steel rivet head
a) Raised double dash
c) Raised cross

b) Raised dash
d) No marking on head

31. A hole is corroded which cannot be removed, is repaired by


a) Scrap out the part
b) Helicoil
c) Acres sleeve
d) Use special washer
32. Tw=100;
a) 150 in lbs
c) 175 in lbs

Te=? Extension=5,
b)
d)

33. For shear joint


a) Clevis pin
pin

b)Taper pin

A=20 (Torque wrench)


125 in lbs
200 in lbs

c) Roll pin

d) Cotter

34. Solid rivet of 1/8 diameter is replaced by (CAP)


a) Two rivet of 1/16 diameter
b) Three rivet of 1/16 diameter
c) Four rivet of 1/16 diameter
d) Cannot be replaced
35. Colour code for o-rings
a) Red dot for hydraulic fluid
b) Green dot for fuel
c) Yellow dot for skydrol fluid
d) d) None
36. For safetying turnbuckles, locking wire is used in
a) Single wrap
b) Double wrap
c) Double wrap spiral
d) All are correct
37. Dzus pastners consist of a stud, grommet and receptacle, stud
length is measured in
a) Tenth of an inch
b) Sixteenth of an inch
c) Hundredth of an inch
d) Thousandth of an
inch
38. A grub screw is a
a) Headless type set screw
b) Cap screw with fine threads
c) Machine screw with flat countersunk head
d) Cylindrical piece threaded at both ends and is plain in the middle
39. Grip length of cherry lock rivet is measured in increments

a) 1/8

b) 3/32

c) 1/16

d)1/32
40. Identifying marks on the head of Al-alloy rivet indicate
a) Shank size
b) Head treatment given by
manufacturer
c) Specific alloy and by manufacturer
d) All are correct
41. The solid shank rivet, which is used in interior of a/c, where
maximum strength is needed
a) round head
b) brazier head
c) flat head
d) as in c) & is AN-442
42. The standard range for counter sunk head angle is
a) 72 - 120
b) 78 - 112
c) 78
100

d)

43. To repair or replacement of protuding head rivet


a) round head
b) counter sunk head is
needed
c) universal head is used
d) any rivet can be
selected
44. For riveting Mg alloy sheet
a) 5056 rivet should be used.
be used
c) mild steel should be used

b) monel rivet should


d) All of the above

45. Which material you select for riveting Ni-steel sheet


a) Monel
b) 2017-T
c) 2024-T6
d) Mild steel
46. Which one of the following rivet is ready for use as received &
need no further heat treatment.
a) 2117
b) 2017-T
c) 2024
d) 1100
47. Ice-Box rivets are
a)2017-T
b) 2117-T

c) 2024-T d) a) & c) are correct

48. The specification for universal head rivet


a) AN-470
b) MS-20613
20615
d) all

c) MS-

49. The protective film of zinc chromate over rivet identified by


a) its yellow colour
b) pearl gray

c) its white colour


50. Part No. AN 470B 3 8 indicates
a) shank diameter is 3
16
c) material is 5056 Al alloy

d) its silver gray colour


b) rivet length is 8
32
d) all of the above

51. Mark the correct statement.


a) Identification marking shall appear either on shank or head of
rivet.
b) The rivet length shall be taken in fraction of 32 of an inch.
c) Group-A, Al-alloy can be used with Group-B Al-alloy keeping in
view the dissimilar metal corrosion factor.
d) Both a) & b) are correct.
52. The material code for 2024 T rivet
a) D
b) AD

c) DD

d) B

53. The absence of latter following the AN-standard number indicate


a) material is Al-alloy
b) material is steel
c) material is mild steel
d) any of the above
54. The head marking Raised triangle, indicate the rivet is
a) 5056
b) 2219
c) 7075
Monel
55. The head marking for 2024-T is
a) raised dot
c) raised three dash

d)

b) raised double dash


d) recessed double dash

56. The marking recessed single dash indicate the rivet is


a) QQW 423
b) QQS-633
c) 2117
d) QQ1-281
57. The shank length used for making blind head in a pull thru rivet is
a) 1
b) -
c) 3/64
d) 3/64 1/8
58. Its proven fatigue strength make it the only blind rivet
interchangeable structurally with solid rivet is
a) wire draw cheeylock rivet
b) dill lock rivet
c) bulb cherrylock rivet
d) deutsch rivet
59. To joints requiring an excessive amount of sheet take-up, you
may select

a) pin rivet
c) bulb cherry lock rivet
60. Riv nut is
a) hollow, blind rivet
c) counter bored & thread inside

b) wire draw cherrylock rivet


d) all of the above
b) made of 6053-Al alloy & a)
d) all of the above

61. In Part No. 10 KB 106, KB indicates


a) close end & keyless
b) close end & keyed
c) open end & keyed
d) open end & keyless
62. Part No. 10 - B -107 indicates
a) Riv nut having flat head
head
c) Riv nut having counter sunk head

b) Pin rivet having round


d) Deutsch rivet

63. Pin rivet a) not a blind type


b) have the same shear strength as bolt of equal diameter.
c) as in b) & are about 40% weight of bolt
d) all of the above.
64. Pin rivets are used
a) in compression
c) in shear
carry bending load.

b) in tension
d) all of the above & also

65. The Part No. NAS 177 14 17 indicates


a) flat head Jo-bolt
b) flat head Avdelok fastener
c) flat head pin rivet
d) counter sunk head, pin rivet
66. The hardware pre-lubricated & must not be degreased before
assembly is/are
a) Jo-bolt
b) Avdelok Fastener
c) Both a) & b) are correct
d) Huck mechanical lock rivet
67. The AN-3 to AN-20 (hex head a/c bolt) is
a) General purpose bolt
b) Close tolerance bolt
c) Internal wrenching bolt
d) Special purpose bolt
68. Mark the correct statement.
a) Steel bolt smaller than No.- 10-32 are not use in primary
structure.

b) The AN-3 & AN-73 series bolt are interchangeable for all practical
purpose.
c) b) is correct from the stand point of tension & shear strength.
d) All are correct.
69. Bolt can be identified
a) by material
c) a) & shape of head

b) by method of securing
d) all of the above

70. The head marking on bolt indicate


a) bolt material
b) name of manufacturer
c) a), b) & whether bolt is a standard type or special purpose bolt.
d) a) & b) are correct
71. The marking for corrosion resistant steel bolt is
a) raised dash b) asterisk
c) single raised dash
d) two raised dash
72. For a bolt, part no. AN3DD5A indicates
a) bolt is drilled for saftying
2017 Al-alloy
c) diameter bolt is 5/16

b) material of bolt is
d) length of bolt is 5/8

73. Eye bolt is used


a) where internal tension load is applied.
b) head is slotted to received common screw driver.
c) used for external tension load.
d) both b) & c) are correct.
74. Mark the correct statement.
a) where, there is not much clearance, stump type lock bolt is
used.
b) alloy steel lock bolt may be used to replace steel Hi-shear rivets.
c) as in b) provided the diameter and head is similar.
d) both a) & c) are correct.
75. Bolt part no. ALSF E 88 indicates
a) brazier head, stump type lock bolt
type lock bolt
c) counter sunk, stump type lock bolt
type lock bolt
76. The specification AN 335 indicates

b) flat head, stump


d) counter sunk, pull

a) fine thread, light hex nut


hex nut
c) coarse thread, check nut
hex nut

b) fine thread, plain


d) coarse thread, plain

77. Castellated shear nut is used


a) in tension application.
b) in shear application only.
c) as in a) & with drilled clevis bolt, taper pin etc.
d) as in b) slotted for safety.
78. Stainless steel self locking nut
a) having locking shoulder & key.
b) used in application where temperature exceed 250 F.
c) a) , b) & also called high temperature self locking nut.
d) all are wrong.
79. Material used for Tinnerman instrument mounting nut is
a) Al-alloy
b) Steel alloy
c) Brass
d) Monel
80. Mark the correct statement.
a) Elastic stop nut can be used many time.
b) As in a) & when turn with fingers, replace it.
c) Every time the parts disassembled, replace the elastic stop nut.
d) As in c) & used at place where temperature exceed 250F.

PAPER - II
PART I
ANSWER:1. D

2. C

3. C

4. B

5. B

6. D

7. A

8. B

9. A

10. B

11. A

12. B

13. C

14. C

15. A

16. D

17. B

18. B

19. C

20. D

21. A

22. C

23. D

24. D

25. C

26. B

27. A

28. B

29. C

30. B

31. C

32. B

33. B

34. C

35. C

36. D

37. C

38. A

39. C

40. C

41. D

42. B

43. C

44. A

45. A

46. A

47. D

48. D

49. A

50. C

51. A

52. C

53. C

54. B

55. B

56. A

57. D

58. C

59. B

60. D

61. B

62. C

63. D

64. C

65. D

66. C

67. A

68. D

69. D

70. C

71. C

72. D

73. C

74. D

75. B

76. D

77. D

78. C

79. C

80. B

PAPER - II
PART II

a.
b.
c.
d.

To
To
To
To

increase mechanical strength and tackiness


reduce mechanical strength and tackiness
increase the mechanical strength and reduce tackiness
reduce the mechanical strength and increase tackiness

2. Which type of Synthetic rubber will be the first choice for


manufacturing of aircraft tubeless tyre
a. Butyl rubber b. Neoprene rubber
c. BUNA-N d. thiokol
3. Which synthetic rubber is chiefly used in aircraft hot air duct as
sealing ring and wire insulation
a. Silicon rubber b. Polymethane rubber c. BUNA-S d. BUNA-N
4. Highest resistance to deterioration but lowest physical property
is the characteristic of which kind of synthetic rubber.
a. GR I
b. GR S
c. GR P
d. GR A
5. To valcanise thiokol rubber, which element to be added
a. Sulfur
b. Sulfur oxide
c. Zinc
d. Zinc oxide
6. Which material is used for manufacturing of hydraulic booster piston
seal
a. Styrene butadiene seal
b. Nitrile rubber
c. Flexon rubber
d. Fluoro carbon rubber
7. Natural rubber attains fibrous structure when
a. It under goes at low temperature
b. It is frozen
c. It is heated to 1300C
d. It undergoes continues stress at
normal temperature

8. The grade of Kevlar fiber is used for aircraft structure

a. Kevlar 49

b. Kevlar 149

c. Kevlar 29

d. Kevlar

129
9. The composition for E glass is
a. Magnesia-alumina-silicate glass
borosilicate glass
c. Soda borosilicate glass

b. Lime-alumina
d. None of the above

10. Truly outstanding properties of strength competes with stronger


steel is kind of fiber
a. S glass
b. Hollow fibre glass
c. A glass
d. Carbon glass
11. Which composit material is difficult to cut or drill
a. Glass fibre
b. Aramid
c. Carbon / Graphite
d. None of above
12. Mark the wrong statement for carbon / graphite fibre
a. Is used to fabricate primary structure b. It has high strength
and high rigidity
c. It takes compressive load
d. It is ductile in nature
13. Corrosion control techniques are employed when corbon fibre is in
contact to aluminium
a. A layer of fiber glass is used as a barrie
b. Aluminium is anodized, primed and painted prior to assembly
c. Both (a) and (b) will be applied together
d. None of the above
14. Which composite material is useful for making aircraft parts that
are subject to high stress and vibration
a. Fibergalss
b. Aramid c. Carbon / Graphite
d. None of
these
15. Mark the correct statement
a. Carbon fiber are electrically non conductive
b. Carbon fibers have high thermal expansion
c. Carbon fibers have high fatigue resistance
16. Boron fibers are made by sintering the boron elements on a thin
film of material
a. Titanium
b. Tin
c. Tungsten
d. All above

17. Which fiber material bears all tension, compression and bending
stresses
a. Ceramic fiber b. Boron fiber
c. Fiber glass
d. Graphite
fiber
18. Mark the correct statement in Fiber Orientation
a. Warp direction is designated at 900
b. Weft is designated at 00
c. Bias is at 450 angle of fill threads
d. None of the above
19. For repairing of fabric, which weave to be used
a. Plain weave
b. Basket weave c. Satin weave
these

d. All of

20. Find out the wrong answer: Hybrids of composite material used in
Aviation field are
a. Kevlar with carbon / graphite
b. Kevlar with fiber
glass
c. Carbon / graphite with fiber glass
d. None of these
21. In fiber science, which acts as a curing agent
a. Resin
b. Matrix
c. Catalyst
these
22. Plexiglass is
a. Thermoplastic b. Thermoset
d. None of these

d. All of

c. Laminated

23. Mark the correct answer:


Apart from strongest adhesive characteristics of epoxy resin, it
has other advantages
a. Useful at very high temperature
b. It withstand bending
stress
c. Reasonable rigidity and flexibility
d. All of these
24. Mark the correct answer:
The advantages of fillers to add to resins are
a. To control viscosity and weight
b. To increase pot life
and strength
c. Both (a) and (b)
d. None of these
25. Nomex is a

a. Filler material b. Matrix


Core material
26. Tapered roller bearing support
a. Radial load
b. Thrust load

c. Reinforced fiber

d.

c. Both (a) and (b)

27. Bearing used on high powered aircraft engine is


a. Ball bearing
b. Roller bearing c. Plain bearing
Both (a) and (c)

d.

28. Plain bearings are used for


a. Connecting rods
b. Crank shaft
d. All of these

c. Cam shaft

29. Bearings are used to take


a. Thrust load
b. Radial load
d. Both (a) and (b)

c. Side load

30. Bearing used where high compressive pressure, is generally made


of
a. Babitt
b. Bronze
c. Siliver bronze d. All of these
31. Bearing which offer more friction is made of
a. Bronze
b. Babitt
c. Silicon
these

d. None of

32. The amount of electricity a capacitor can store is directly


proportional to
a. Distance between the plate and inversely proportional to the
plate area
b. Plate area and is not affected by the distance between the
plate.
c. Plate area and inversely proportional to the distance between
the plate
d. None of these
33. The correct way to connect a test volt meter in a circuit is
a. In series with a unit
b. Between the source voltage and
the load
c. In parallel with unit
d. Both (a) and (c) are correct
34. Typical application of Zener diode is as
a. Full wave rectifiers
b. Half wave rectifier
c. Voltage regulator
d. Amplifier

35. The method used to rapidly charge a Nickel Cadmium battery


utilizes
a. Constant current and constant voltage b. constant current and
varying voltage
c. Constant voltage and varying current
d. Varying voltage and varying current
36. What tasks are completed prior to weighing an aircraft to
determine its empty weight
a. Remove all items except those on aircraft equipment list,
drain fuel and hydraulic fluids
b. Remove all items on the aircraft equipment list, drain fuel,
compute oil and hydraulic fluid weight
c. Remove all items except those on the aircraft equipment list,
drain fuel and fill hydraulic reservoir
d. All of these
37. Useful load of an aircraft is the
a. Difference between the maximum gross weight and empty
weight
b. Difference between the net weight and total weight
c. Some of the empty weight and the max. gross weight
d. Weight of the fuel
38. Certain amount of slacks must be left in flexible hose during
installation because when under pressure it
a. Expand in length and diameter
b. Expand in length and contracts in diameter
c. Contracts in length and expands in diameter
d. Contracts in length and diameter
39. Excessive stress on fluid or pneumatic metal tubing caused by
expansion or contraction due to temperature change can best be
avoided by
a. Using short, straight sections of tubing between fixed parts of
aircraft
b. Not projecting the aircraft to sudden change in temperature
c. Providing bends in the tubing
d. None of the above
40. Which heat treating process of metal produces a hard, wear
resistance surface over strong, tough core
a. Case hardening
b. Annealing
c. Tempering
d. Hardening

41. Which of the following hose materials are compatible with


phosphate-ester base hydraulic fluids
a. Butyl
b. Buna-N
c. Neoprene
Buna-S

d.

42. In a metal tubing installation


a. Rigid straight line runs are preferable
b. Tension is undesirable because pressurisation will cause is to
expand and shift
c. A tube may be pulled in if the nut will start on the threaded
coupling
d. None of the above
43. Magnetic particles inspection is used primarily to detect
a. Distortion
b. Deep surface flaw
c. Flaws on or near the surface
d. Flaws in plastic
material
44. Which material cannot be heat treated repeatedly without harmful
effects
a. Unclad aluminium alloys in sheet forms
b. 6061- T9 Stainless steel
c. Clad aluminium alloy
d. Carbon steel
45. What is generally used in the construction of aircraft engine fire
walls
a. Stainless steel
b. Chromium
Molybdenum alloy steel
c. Magnesium Titanium alloy steel
d. Wrought iron
46. A fiber type self locking nut must never be used on an aircraft if
the bolt is
a. Under shear loading
b. Under tension loading
c. Subject to rotation
d. All of these

47. Aircraft bolts are usually manufactured with a


a. Class-I fit for the thread
b. Class-II fit for the thread
c. Class-III fit for the thread
d. Class-IV fit for the thread
48. Hose and a few projecting globules are found in a weld. What
action should be taken

a. Re-weld the defective portions


b. Remove all the old weld and re-weld the joint
c. Grind the rough surface smooth, inspect and re-weld all gaps /
holes
d. Can be used in the same way
49. Which condition indicate a part has cooled too quickly after being
welded
a. Cracking adjacent to the weld
b. Discoloration of the base metal
c. Gas pockets and porosity
d. Slag inclusion
50. Which tool is used to measure the clearance between the surface
plates and a relatively narrow surface being checked for flatness.
a. Depth gauge b. Thickness gauge
c. Dial indicator
d. Vernier Caliper
51. Which tool is used to find the center of a shaft or other cylinder
work
a. Combination set
b. Dial indicator c. Micrometer caliper
d. Set square
52. What tool is generally used to calibrate a micrometer or check its
accuracy
a. Gauge block b. Dial indicator c. Machinist scale
d.
None of these
53. When approaching the front of an idling jet engine the hazard area
extends forward of the engine approximately
a. 10 feet
b. 15 feet
c. 25 feet
d. 35 feet
54. Which of the following is the most satisfactory extinguishing agent
for use on a carburetor or intake fire
a. Dry chemical b. A fine water mist
c. Carbon dioxide
d. Form
55. When approaching the rear of an idling turbo jet engine the hazard
area extends aft of the engine approximately
a. 200 feet
b. 100 feet
c. 50 feet
d. 25 feet
56. When towing a large aircraft
a. A person should be in the cockpit to watch the obstruction
b. Person should be stationed at the nose

c. Person should be positioned each wing tip and the


empennage
d. A person should be in the cockpit to operate brakes
57. A fuel that vaporizes too readily may cause
a. Hard starting b. Detonation c. Vapor lock d. None of these
58. The main difference between grades 100 and 100LL fuel are
a. Volatility and lead content
b. Volatility, lead content and
colour
c. Lead content and colour
d. All of these
59. Tetra ethyl lead is added to aviation gasoline to
a. Retard the formation of corrosive
b. Improve the gasoline performance in the engine
c. Dissolve the moisture in the gasoline
d. None of these
60. If the temperature of a confined liquid is held constant and its
pressure is trippled, the volume will
a. Triple
b. Reduced to one third its original volume
c. Remains same
d. Multiply by a fixed factor

PAPER - II
PART II
Answers:
1c

2a

3a

4c

5d

6b

7b

8a

9b

10 d

11 b

12 d

13 c

14 b

15 c

16 c

17 b

18 d

19 c

20 d

21 c

22 a

23 d

24 c

25 c

26 c

27 b

28 d

29 d

30 b

31 a

32 c

33 c

34 c

35 c

36 c

37 a

38 c

39 c

40 a

41 a

42 b

43 c

44 c

45 a

46 c

47 c

48 b

49 a

50 b

51 a

52 a

53 c

54 c

55 b

56 d

57 c

58 c

59 b

60 b

PAPER - II
PART III
1. During towing operations
a) Pilot must be in the cockpit to operate brakes
b) A qualified person should be in the cockpit to operate brakes
c) A person should be in the cockpit to look for obstructions
d) Persons should be stationed at the nose and each of the wing-tips
2. Tail-wheel type aeroplanes have the greatest tendency to move
side-ways during taxing when there is
a) Cross wind
b) Tail wind
c) Head wind
d) None of these
3. When parking a aircraft after towing, the nose wheel should be left
a) Pointed straight ahead
b) As it was when towing stopped
c) Unlocked
d) All are correct
4. Before towing a large aircraft
a) Ballast should be put in the cockpit
b) Tow bar should be fitted with a strong bolt
c) Tow bar should be fitted with a shear bolt
d) None of these
5. While towing a large aircraft, personnel required are
a) Two in cockpit
b) As in a) plus one each on wing tips
c) As in b) plus one at the tail
d) As in c) plus one in overall control of operation

6. The most commonly used driving tool by a mechanic is


a) Ball peen hammer
b) Cross peen hammer
c) Claw hammer
d) Sledge hammer
7. (i) Body hammers are used for driving stakes into the ground
(ii) Sledge hammers are used for smoothing or stretching the metal
a) Only (i) is correct
b) Only (ii) is correct
c) Both (i) and (ii) are correct
d) Neither (i) nor (ii) is
correct
8. i) Mallets can be termed as soft hammers
ii) Plastic mallets are more useful than raw hide mallets
a) Only (i) is correct
b) Only (ii) is correct
c) Both (i) and (ii) are correct
d) Neither (i) nor (ii) is
correct
9. (i) Claw hammers are basically used for driving and pulling out nails
(ii) The wedge of a cross peen hammer is parallel to the handle
a) Only (i) is correct
b) Only (ii) is correct
c) Both (i) and (ii) are correct
d) Neither (i) nor (ii) is
correct
10. A punch is used to
a) Mark a location
c) Locate a drill properly

b) Remove a damaged rivet


d) All are correct

11. i) A pin punch is used to remove the shank of the rivet from the
hole after rivet head has been chiselled off
ii) Diameter of pin punch should be 1/64 inch smaller than the
diameter of the rivet to be removed
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
12. i) Location given by a prick punch should always be punched later
with a centre punch.
ii) Goggles must be used while using any type of punch.
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
13. i) A mushroom head on a punch is better than a crown head since
chances of hammer slip are reduced
ii) A centre punch can be used for a variety of punching applications
a) Only i) is correct
b) Only ii) is correct

c) Both i) and ii) are correct

d) Neither i) nor ii) is correct

14. Most commonly used slip joint plier has a length of


a) 4 inches
b) 6 inches
c) 10 inches
inches
15. Duckbill plier
a) Is a flat nose plier
c) Have serrations on their jaws

d) 12

b) Is used for twisting safety wires


d) All are correct

16. Needle nose pliers are used for


a) Extracting thin/sharp components
nails
c) Gripping small electronic components

b) Extracting
d) All are correct

17. i) A chisel can never cut the material all by itself


ii) A die is a cutting tool
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
18. Cutting edge of a chisel is generally ground to an angle of
a) 30 degrees
b) 70 degrees
c) 90 degrees
d) 110 degrees
19. Regarding a cutting chisel which statement is incorrect?
a) It is made from high grade steel
b) Its cutting edge is always wider than the shank
c) Cutting edge is flat so that force is applied uniformly on the surface
d) Chisel body is either square or octagonal
20. i) A cape chisel is the proper tool to use for knocking the head off
a rivet after it has been drilled through
ii) A cape chisel is forged from the same type of tool steel as the cold
chisel
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
21. Aviation snip
a) Is same as Dutchman snip
c) Can easily cut thick sheet metals

b) Has serrated cutting edges


d) All are correct

22. Files are classified with regard to


a) Physical shape
b) Length
c) Type of cut
d) All are correct
23. Various types of cut of a file are
a) Single cut
b) Smooth cut
c) Rasp
d) Both a) & b) are correct
24. Vixen file have
a) Curved teeth
c) A special file holder

b) No taper either in width or thickness


d) All are correct

25. i) Wood rasp files have individual teeth cut on to their surfaces
ii) Wood rasps are used to remove wood from a surface where it is not
practical to use a saw or a plane
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct

26. i) Mill files have uniform thickness, but are tapered in width
ii) Hand files have uniform thickness and width
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
27. i) Half round files are tapered in both thickness and width
ii) Knife files are tapered in thickness as well as in width
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
28. For filing acute angles, one should use
a) Knife files
b) Round files
c) Triangular files
d) All are correct
29. Most files used in aviation have a length of
a) 4-10 inches
b) 6-12 inches
c) 6-16 inches
d) 10-20 inches
30. The part of a file that fits into the handle is called
a) Heel
b) Fitting end
c) Tang
d) Point
31. i) File is basically a chisel but with many cutting edges
ii) Triangular files are used for cutting teeth of handsaws
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
32. Double cut files have rows of teeth. These teeth are set at

a) 45 degrees and 70-80 degrees


degrees
c) 70-80 degrees and 70-80 degrees

b) 45 degrees and 45
d) None of these

33. There are five cuts of files ranging from coarsest to the finest.
Find out the wrong one
a) Coarse
b) Bastard
c) Smooth
d) Finest
34. File should be kept clean by
a) Tapping it against the bench
c) Lubricating it occasionally

b) Brushing it with a wire brush


d) Both a) & b) are correct

35. Which type of file has only three grades: regular, fine and smooth
a) Vixen
b) Wood rasp
c) Knife
d)
Triangular

36. Characteristics of steel are controlled by


a) Removal of carbon from iron
elements added to it
c) Amount of alloying elements added to it

b) Types of alloying
d) All are correct

37. Bearing strength of a material refers to


a) Direct tensile load it can bear
b) Resistance to tear at the point of applied load
c) Resistance to fracture at the point of applied load
d) Resistance to shear
38. Characteristics of metals relating to drawing it into wire is
a) Tensile strength
b) Malleability
c) Ductility
d) Brittleness
39. Fusibility of a metal refer to its property that permits
a) Welding
b) Drawing into thin sheets
c) Drawing into wires
d) Good thermal conductivity
40. Aluminium alloy 1100 implies
a) Pure aluminium
b) It contains 11% copper
c) It contains 111% zinc
d) Heat treated alloy
41. Aluminium alloys have a four digit index system where each digit
signifies something. In 2024, the first digit indicates
a) Copper is the major alloying element
b) Two alloying elements have been added

c) Total percentage of alloying elements


d) None of these
42. Alclad is a metal consisting of
a) Aluminium alloy core with pure Al surface
b) Pure aluminium core with Al alloy surface
c) Alternating layers of pure Al & Al alloys
d) None of these
43. Which of the following aluminium alloy is heat treated and
artificially aged?
a) 3003-F
b) 5052-H
c) 6061-O
d) 7075-T6
44. Clad aluminium alloys are used in aircraft. They are
a) Lighter than other aluminium alloys
b) Stronger than unclad
aluminium alloys
c) Easily heat treatable
d) Less susceptible to corrosion

45. Aircraft structural members made from sheet metal can normally
be
a) Repaired, except when subjected to compressible loads
b) Repaired, except when subjected to tensile loads
c) Repaired using approved method
d) Not repaired & need replacement only
46. Medium carbon steels have a carbon percentage of
a) 0.1 0.3
b) 0.3 0.5
c) 0.5 1.0
d) 1.0 2.0
47. High carbon steel is generally used for
a) Shock absorbers
b) Landing gear struts
c) Engine mounting bolts
d) Springs & files
48. What material is used in the construction of firewall of aircraft
engines?
a) Aluminium alloy
b) Stainless steel
c) Chrome-molybdenum steel
d) Tungsten steel
49. Which of the statement is correct?
a) Both heat treatable & non heat treatable aluminium alloys can be
strain hardened
b) Strain hardening is same as cold working
c) Strength & hardness increases during cold working

d) All are correct


50. Find out the wrong statement regarding titanium
a) It is highly corrosion resistant
b) It maintain strength at elevated
temperatures
c) It has good resistance to creep d) It is magnetic
51. The balls used for ball bearings are made of
a) Cast iron
b) Cast steel
c) Wrought iron
d) Carbon chrome steel

52. Files used in fitting shop are made from


a) Cast iron
b) High carbon steel
c) Chrome steel d) Mild steel
53. Property of a material to be drawn plastically before breaking is
called ductility. Most ductile material is
a) Copper
b) Gold
c) Lead
d) Tin
54. i) Aluminium has high electrical and thermal conductivity
ii) Ductility of aluminium improves with the addition of iron & silver
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
55. i) Muntz metal is same as yellow brass
ii) Muntz metal contains copper & zinc in the ratio of 3:2
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
56. Potential difference between two conductors insulated from each
other is measured in
a) Ampere
b) Coulomb
c) Ohm
d) Volt
57. Correct way to connect a test voltmeter in a circuit is
a) In series with a unit
b) In parallel with a unit
c) Between source voltage and load
d) Both b) & c) are correct
58. Which term means .001 ampere
a) Micro ampere
b) Milli ampere
c) Kilo ampere
d) Nano ampere
59. Unit used to express electrical power is
a) Ampere
b) Volt
c) Watt

d) Coulomb

60. Transfer of electrical energy from one conductor to another without


the aid of electrical connection is
a) Induction
b) Air gap transfer
c) Not possible
d) Possible but will cause excessive arcing thus
not practical
61. Magnetic lines of force pass most readily through
a) Aluminium
b) Copper
c) Iron
d) Titanium

62. In a straight conductor, the resistance is not affected by


a) Length
b) Temperature
c) Shape of cross section
d) Material
63. Pitot pressure varies with
a) Speed b) Air density
c) Speed and Air density
d) None of these
64. Altimeter and rate of climb indicator utilize
a) Static pressure b) Pitot pressure
c) Either a) or b)
d) Both a) and b)
65. Pitot static system have heating elements to
a) Remove moisture from the air
b) Prevent ice formation
c) To permit flying at high altitude
d) All are correct
66. Pressure heads of pitot static system should not be painted,
because it
a) Impairs their thermal efficiency
b) May cause obstruction of
orifices
c) None of the above
d) Both a) and b) are correct
67. Leak test of pitot static system should be carried out
a) After installation of a component / instrument
b) Whenever malfunctioning is suspected
c) At specified periods indicated in servicing schedules
d) All are correct
68. Which instruments are connected to the aircraft pitot static
system?
a) Vertical speed indicator
b) Altimeter
c) Airspeed indicator
d) All are correct

69. The instrument that measures difference between pitot & static
pressure is
a) Altimeter
b) Pressure gauge
c) Airspeed indicator
d) Vertical speed indicator
70. The unit where calculations are processed is called
a) Central processing unit (CPU)
b) Control unit
c) Arithmetic and logic unit (ALU)
d) Computing unit
71. Sequence of steps for computing a program is known as
a) Flow chart
b) Sequence process
c) Algorithm
d) None of these
72. Basic function of a computer is
a) Addition
b) Multiplication
73. EDP stands for
a) Electrical data processing
c) Entry data processing
programme

c) Division d) All are correct


b) Electronic data processing
d) Electronic discrete

74. A computer basically


a) Processes data
b) Stores data as per given
instructions
c) Perform mathematical calculations
d) All are correct
75. Computer stores instructions in
a) English language
c) Octal number system

b) Decimal number system


d) Binary

76. In a straight and level flight of an aircraft


a) Lift equals aircraft weight
b) Lift is more than weight
c) Lift is less than weight
d) Depends upon size of aircraft
and its loading
77. Whenever lift is generated, there is certain amount of drag
associated with it. This is called
a) Form drag
b) Skin friction drag
c) Induced drag
d) Shape drag
78. Lift generated by an airfoil is maximum at an angle of attack of
about
a) 0 degrees
b) 4 degrees
c) 12 degrees
d) Stalling value

79. Lift generated by an aircraft depends upon


a) Density, forward velocity & aircraft area
b) Density, square of forward velocity and aircraft area
c) Density, square of forward velocity and wing area
d) Density, forward velocity & wing area
80. Lift on a wing
a) Acts through centre of gravity
b) Acts vertically upwards
c) Is perpendicular to chord line
d) Acts vertically upwards through centre of pressure

PAPER - II
PART III
1. B
6. A
11. A
16. C
21. D
26. A
31. C
36. D
41. A
46. B
51. D
56. D
61. C
66. D
71. C
76. A

2. A
7. B
12. C
17. C
22. D
27. D
32. A
37. B
42. A
47. D
52. B
57. B
62. C
67. D
72. A
77. C

3. A
8. C
13. D
18. B
23. A
28. A
33. D
38. C
43. D
48. B
53. B
58. B
63. C
68. D
73. B
78. D

4. C
9. A
14. B
19. C
24. D
29. C
34. D
39. A
44. D
49. D
54. A
59. C
64. A
69. C
74. D
79. C

5. D
10. D
15. D
20. C
25. C
30. C
35. A
40. A
45. C
50. D
55. C
60. A
65. B
70. C
75. D
80. D

PAPER - II
PART IV
1. While pushing a small and light aircraft, generally
a) Rudder control should not be locked
b) It should be pushed backward rather than forward
c) Flats of the hands should only be used
d) All are correct
2. While moving an aircraft from the runway after an emergency
a) It should be towed away fast
b) It should never be towed away with deflated tyres
c) Brakes should never be applied
d) All are correct
3. For picketing a light aircraft
a) Cable or any rope should be used
b) Sufficient slack should be given for all types of ropes
c) Aircraft should be parked into the wind
d) Both a) & c) are correct
4. Before jacking an aircraft
a) Empty the fuel tanks
b) Fit critical stress panels
c) Level aircraft laterally
d) Remove all optional equipment
5. It is generally necessary to jack an aircraft for weighing. Why?
a) To set the weighing scales to zero
b) To stabilize the weighing scales
c) For first determining its empty weight
d) For making aircraft level

6. (i) In cross filing, the file is moved length wise across the work
(ii) In draw filing, the file is moved side wise across the work
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
7. A handsaw used for cutting across the grains of wood is called a
a) Cross cut saw
b) Rip saw
c) Back saw
d) Wood saw
8. A cross cut saw has
a) 4-6 teeth per inch
c) 10-15 teeth per inch

b) 6-12 teeth per inch


d) 12-18 teeth per inch

9. Find out the incorrect statement regarding back saw


a) It is used for cutting precision parts
b) It has 18-32 teeth per inch
c) It is same as hacksaw
d) Cutting teeth has very little set
10. Hacksaw blades are
a) Made from stainless steel
b) 12 inches in length
c) Held under tension in the frame d) Having 10-14 teeth per inch
11. i) Hacksaw blades are made of either carbon steel or high steel
molybdenum steel
ii) While using hacksaw, cutting is done only on the forward stroke.
The blade should be lifted for the return stroke
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
12. i) For a good cut on a hard material, a blade with more teeth
should be used
ii) While cutting a tube, a blade should be so chosen that at least five
teeth are there on each side of the tube as it is cut
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
13. Length of hacksaw is measured from
a) The outer edge
b) toothed part of blades
c) Between the centre of fixing holes
d) Both a) & b) are
correct
14. Spiral anger bit for drilling holes in wood are
a) Generally 7-10 inches long
b) - one inch in diameter

c) Used only with a bow type hand brace d) All are correct
15. A screw driver can be used
a) For driving screws
c) As a chisel
16. Stubby screw driver has
a) A blunt edge
c) Only wooden handle

b) As a punch
d) All are correct
b) Blade length of up to 2
d) All are correct

17. Screw driver used when there is no clearance for normal screw
driver is called
a) Closed area screw driver
b) Stubby screw driver
c) Off set slot screw driver
d) Any one of the above
18. Air driven power screw driver should be used
a) For large diameter screw
b) For removing screw that are jammed
c) Where large number of screws are to be removed and fitted back
d) When removing screws from harder material
19. A slot screw driver should have sufficient size of the blade to cover
certain width of the screw slot. It should cover at least
a) 50%
b) 60%
c) 75%
d) 90%
20. i) Cross point screw driver causes less damage than straight edge
screw driver
ii) Phillips screwdriver require less efforts as compared to normal
screw driver
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
21. With regard to wrenches, find out the incorrect statement
a) These are made from chrome vanadium steel
b) These are generally die cast
c) Wrenches are made in various shapes & sizes
d) These are plated to improve their appearance
22. Open end wrenches
a) Ends are inclined so as to allow the wrench to turn the nut even in
restricted space
b) Are available in British & Metric sizes
c) Open a nut faster than box end wrenches
d) All are correct

23. Box end wrenches are used


a) To loosen nuts that are exceptionally light
b) Where there is restricted space
c) For nuts that are bigger than one inch size
d) When open end wrench is not available
24. Combination wrenches means, its two ends have
a) Open and box end
b) Open and cut box end
c) Open and flare nut end
d) All are correct

25. i) Loosing or tightening of a nut takes longer time if box end


wrench is used
ii) Box end wrenches can easily open a very tight nut because it grips
the nut at many places compared to an open ended wrench
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
26. i) A flare nut wrench is a special type of box end wrench
ii) Flare nut wrench is used basically for opening and fitting of pipelines
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
27. Spanners are classified by
a) Type
b) Material
c) Size of the bolt/nut on which it fits
d) All are correct
28. Set spanners are off set to an angle
a) So that it can be used in restricted places
b) A new grip can be got by turning the spanner over
c) For proper grip
d) Both a) & b) are correct
29. Ratchets
a) Allow removal of nut with very small amount of handle movement
b) Are available with long and short handles
c) Can easily fit into sockets
d) All are correct
30. Crowfoot socket wrench is used where the following cannot be
used
a) Open end wrench
b) Box end wrench

c) Standard socket wrench

d) All are correct

31. Monel metal is an alloy of


a) Nickel & copper
b) Nickel & chromium
c) Copper & chromium
d) Copper, nickel & chromium
32. i) Gun metal is used for gears & bearings.
ii) Brass is used for cartridge cases
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct

33. SAE 2340 is


a) Chromium steel with 3% chromium
b) Nickel chromium steel with 0.3% carbon
c) Nickel steel with 3% Nickel & 0.4% carbon
d) Carbon (0.4%) steel
34. Engine mounts are made up of
a) 18-8 corrosion resistance mild carbon steel
b) Chrome molybdenum mild carbon steel
c) Chrome molybdenum high carbon steel
d) None of these
35. During nitric acid test, if the material shows strongly magnetic
nature, then it is
a) Monel metal
b) Carbon steel
c) Nickel steel
d) 18-8 steel
36. Weldability is poorest in case of
a) Plain carbon steel
b) Low carbon steel
c) High carbon steel
d) Wrought iron
37. Carbon steel is
a) Refined form of cast iron
b) Extremely hard
c) Made by adding carbon to steel
d) An alloy of iron & carbon with varying quantities of sulphur &
phosphorous
38. Stainless steel is corrosion resistance due to presence of
a) Silicon
b) Cobalt
c) Chromium
d) Manganese

39. Manganese is added to low carbon steel to


a) Make them tough & hard
b) Raise their tensile strength
c) Improve machine ability
d) Increase corrosion resistance
40. Cold bending of an aluminium sheet
a) Is not permitted
b) Softens the material at the bend
c) Strain hardens material at the bend
d) Results in material failure irrespective of bend radius

41. Titanium can be identified by


a) Chemical test
c) Moistening & scratching with pencil
correct

b) Spark test
d) Both b) & c) are

42. L shaped channels are produced by


a) Forging
b) Extrusion
c) Machining
d) Casting
43. Muntz metal is used for
a) Nuts & bolts
c) Fuel & oil lines

b) Parts in contact with salt water


d) Both a) & b) are correct

44. All carbon steels have well defined critical point & range. Low
carbon steel has
a) Two critical points
b) Three critical points
c) Four critical points
d) Six critical points

45. In steel, grain becomes coarser when


a) It is heated to a temp just below critical point
b) It is heated above critical range
c) Depends upon carbon percentage
d) It does not happen at all
46. Creep in metals is
a) Elongation due to temperature
b) Temporary elongation due to temperature and stresses
c) Permanent set due to stresses and high temperature operation
d) All are correct

47. Magnesium alloys are


a) Magnetic
b) Light in weight
c) Cheap & easy to machine
d) Highly prone to corrosion
48. i) Bronze is superior to brass in corrosion resistance property
ii) Duralumin can be age hardened
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
49. i) Clad metals are two dissimilar metals joined together under high
hydraulic pressure
ii) Clad metals mean forged non ferrous metals
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
50. Aluminium alloys 2017 & 2024 must be transformed from the heat
treatment medium to quench tank within 10 seconds or so. A delay
results in
a) Retarded age hardening
b) Reduced corrosion resistance
c) Dull/Strained surface
d) Hard/brittle surface
51. Power and work are measured in
a) Watt and force
b) Watt and joule
c) Ampere hour and joule
d) Farad and joule
52. One micron is
a) 10-3 meter
c) 10-9 meter

b) 10-6 meter
d) None of these

53. The change in resistance depends upon


a) Temperature
b) Material and length
c) Cross sectional area
d) Both b) and c) are correct
54. Most extensively used material in aircraft electrical cables is
a) Rubber and silk
b) Nylon and cotton
c) Teflon
d) Both b) & c) are correct
55. In a parallel circuit
a) Total resistance is less than smallest resistor
b) Total resistance decreases when one of the resistance is removed
c) Total voltage drop is same as total resistance
d) All are correct

56. If there are n numbers of calls, each having a voltage of E and


resistance R, then voltmeter connected across the electrolyte will
indicate
a) nE
b) (n-1)E
c) n(n - )E
d) None of these
57. A 12V bulb is connected in series and draws 3 amperes current
from a 12V battery. Its resistance and power will be
a) 36 ohms, 4 W
b) 4 ohms, 36 W
c) 1 ohm, 12 W
d) None of these
58. The number of shock mounts required for an original instrument
panel is determined by the
a) Size of the panel
b) Type of the panel
c) Weight of the complete panel unit
d) Number of
instruments to be installed
59. Aircraft instrument panels are shock mounted to
a) Absorb all vibrations
b) Absorb low frequency, high amplitude shocks
c) Channel most airframe vibrations to the instruments
d) Absorb high frequency, high amplitude shocks
60. The method of mounting aircraft instruments in their respective
panels depends on
a) Instrument manufacturer
b) Design of the instrument
case
c) Design of the aircraft fuselage
d) Design of the instrument
panel
61. How is a flange less instrument case mounted in an instrument
panel?
a) By four screws which extend through the instrument panel
b) By an expanding type clamp secured to the back of the panel and
tightened by a screw from the front of the instrument panel
c) By a metal shelf separate from and located behind the instrument
panel
d) By press fit into the instrument panel and held in place by friction
62. Why are most electrical instruments mounted in iron or steel
cases?
a) To avoid damage to the instrument during maintenance
b) To facilitate removal or installation
c) To prevent interference from outside magnetic fields
d) To reduce heat build up in the instrument

63. When installing instruments in an aircraft who is responsible for


making sure it is properly marked?
a) An authorised inspector
b) The aircraft owner
c) The instrument installer
d) The instrument
manufacturer
64. i) Instrument panels absorb low frequency high amplitude shocks.
ii) Shock absorbers of instrument panel permit instruments to operate
under conditions of minor vibrations.
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
65. Assembler is
a) An individual who assembles computer
c) Programme

b) Language
d) None of these

66. Input unit of a computer communicates between


a) Operator & computer
b) Memory with printer
c) CPU with monitor
d) Output & computer
67. Primary memory of a computer are
a) RAM, ROM
b) RAM, ROM, PROM
c) RAM, ROM, CPU
d) RAM, ROM, Hard Disc
68. Hard disc & floppies are
a) For different purpose
b) For same purpose but hard disc stores more information
c) For same purpose but hard disc stores less information
d) None of these
69. The symbol for hexa-decimal is
a) 2
b) 8
c) 10
70. Algorithm uses
a) One input, one output
c) One input, multiple output

d) 16
b) One input, two output
d) None of these

71. To solve a fifteen step problem, a computer will work in


a) Sequence
b) Repetition
c) Selection
d) Sequence and repetition
72. Which of the following is a storage device?
a) Mouse
b) Monitor

c) CPU
73. RAM stands for
a) Read & access memory
c) Record and maintain

d) Hard disk
b) Random access memory
d) None of these

74. Radio equipment is protected from vibration damage by


a) Shock mounts
b) Aluminium alloy jumpers
c) Doubler plates around the mounting points d) All are correct
75. To communicate with ground control from an aircraft, pilot uses
a) VOR receiver
b) VHF trans receiver
c) HF transmitter
d) ADF

76. Addition of avionics equipment forward of CG limits will affect


a) Maximum gross weight and datum
b) CG limits and useful
load
c) Empty weight and useful load
d) Useful load only
77. i) AC current passing through a conductor creates emf around the
conductor
ii) Frequency of radio wave radiated equals the frequency of the
applied current
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
78. Basic components of a communication system are
a) Receiver & transmitter
b) As in a) plus receiver / transmitter antennas
c) As in b) plus microphone
d) As in c) plus loudspeaker
79. Power output of large commercial aircraft VHF transmitter is of the
order of
a) 1-15 watts
b) 20-30 watts
c) 50-100 watts
d) 150-200 watts
80. An antenna is a special type of electrical circuit designed to
transmit & receive
a) Audible signals
b) Visual signal
c) Electro magnetic energy
d) All are correct

PAPER - II
PART IV
1. D
6. C
11. C
16. B
21. B
26. C
31. A
36. C
41. D
46. C
51. B
56. A
61. B
66. A
71. D
76. C

2. B
7. A
12. A
17. C
22. D
27. D
32. C
37. D
42. B
47. B
52. B
57. B
62. C
67. A
72. D
77. C

3. D
8. B
13. C
18. C
23. A
28. D
33. C
38. C
43. D
48. C
53. D
58. C
63. C
68. B
73. B
78. D

4. B
9. C
14. D
19. C
24. D
29. D
34. B
39. B
44. B
49. A
54. D
59. B
64. C
69. D
74. A
79. C

5. B
10. C
15. A
20. D
25. C
30. D
35. B
40. B
45. B
50. B
55. A
60. B
65. C
70. A
75. B
80. C

PAPER - II
PART V
1. Angular momentum is
a) Moment of inertia
b)
d) Sum of a) & b)

b) Angular velocity

c) Product of a) &

2. Mark the incorrect statement


a) Precession is inversely proportional to the strength & direction of
applied force.
b) Precession is inversely proportional to the moment of inertia of the
rotor.
c) Precession is inversely proportional to the angular velocity of the
rotor.
d) None of the above
3. Control of drift, relating to horizontal gyroscopes can be achieved
by:
a) Calculating corrections using earth rate formula and applying them
as appropriate
b) Applying fixed torques & cause gyro to process at a rate equal &
opposite to the earth rate.
c) As in b) but which can be varied according to latitude
d) All of these
4. When gimbal orientation is such that the spin axis becomes
coincident with one or the other of the axes of freedom which serves
as attitude displacement reference is termed as
a) Gimbal lock
b) Gimbal Error c) Apparent drift
5. When gyroscope as a whole is displaced with its gimbal rings not
mutually at right angles to each other is termed as
a) Gimbal Lock
b) Gimbal Error c) Apparent Drift
6. The vacuum pump or venturi creates a vacuum for operating the
Gyroscope which is regulated by a relief value at
a) 3.5 in Hg
b) 4.5 in Hg
c) Between 3.5 and 4.5 in Hg
d) None
7. Grip length of the bolt is
a) Total length of the bolt
b) Plain shank length of the
bolt
c) Length under the head to the end of the bolt
d) None of these

8. In close tolerance bolt, force applied to drive in is


a) 10 ounce hammer
b) 20 ounce hammer
c) 12 to 14 ounce hammer
d) Sledge hammer
9. AN 4 - 7 bolt shows
a) 7/8 dia
b) 1/4" length
10. Bolt of class 4 fit is
a) Loose fit
b) Free fit

c) 4 length
c) Close fit

d) 1/4" dia
d) Tight fit

11. Special washer AC 950 and AC 955 are used where


a) Bolt is installed at angle to surface
b) Bolt is installed head
down
c) It can be used any where
d) None of these
12. To prevent the crushing surface on wooden structure with nut and
bolt, the washer used is
a) AN 936
b) AN 935
c) AN 970
d) AN 960
13. Where shear load is taken by the bolt, the nut used is
a) Plain nut
b) Castle nut
c) Castellated shear nut
d) Self locking nut
14. In the patch repair of the Aircraft skin, the edge distance (distance
from the center of the rivet to the edge of the sheet) should be (d is
diameter of rivet)
a) 2d to 4d
b) 8d
c) 6d
d) 75% of the
pitch
15. Rasp file is used for
a) Hard material
b) Lead, wood or leather
c) Both a) & b)
d) Other materials except lead, wood & leather
16. Pinning is related to
a) Chisels
b) Punches
these

c) Screw drivers

17. Philips screwdrivers are tapered to an angle of


a) 730
b) 530
c) 600
0
93

d) None of

d)

18. Snaps are used to


a) Support the markers head of rivets
b) To make the shop
head during riveting
c) Both a) & b)
d) None of these

19. Punch used for making a series of light pops along scribed line,
which will be machined or filed away
a) Pin punch
b) Stout punch
c) Light centre punch
d) Parallel pin punch
20. Hand file is related to _______ of file
a) Length of file b) Cut of file
c) Grade of file

d) Section of files

21. Screw drivers are classified by


a) Type and length of blade
b) Type, grade, cut and section
c) Length and type
d) Overall length of screw driver
22. Steel drifts should be used
a) On soft materials
bearing
c) Hardened steel

b) For driving ball or roller


d) None of these

23. Ring spanners are used for


a) Fitting the nut all around
opened jaws
c) Fitting the splined nut
24. Hard hammers are made of
a) High carbon steel
shape and size
c) Tool steel

b) Fitting the nut from


d) None of these
b) Carbon steel and forged to
d) Mild steel

25. Flux used for commutator wires and electrical connections


a) Zinc chloride
b) Zinc chloride by diluting with
50% alcohol
c) Alcoholic solution of rosin
d) Rosin
26. Slotting hacksaw blade is usually of
a) 18 long 3/4" wide
c) 12 long 3/4" wide

b) 8 long 1/2" wide


d) None of these

27. Hacksaw is used by


a) Putting same pressure for forward and backward stroke
b) Putting pressure for forward stroke and release the pressure in
backward stroke
c) Putting less pressure in forward stroke and more pressure in
backward stroke
d) Any of these

28. Which hammers have large, smooth faces and are lightweight?
a) Ball peen hammers
b) Body hammers
c) Cross peen hammers
d) Sledge hammers
29. Soft solder is the combination of tin and lead in proportion of
a) 2 : 3
b) 3 : 2
c) 1 : 4
d) 4 : 1
30. The stresses to which Aircraft are subjected are
a) Tension
b) Torsion
c) Bending

d) All of these

31. The internal force of a substance which opposes the deformation is


called
a) Strain
b) Stress
c) Tension
d) Torsion
32. The twisting load on the structure is called
a) Torsion
b) Tension
c) Strain

d) Compression

33. Bending stress is the combination of


a) Compression and shear
b) Shear and tension
c) Compression and tension
d) Tension and shear
34. Permanent deformation of structure is called
a) Stress
b) Strain
c) Tension

d) Bend

35. In monocoque fuselage construction, main members are


a) Frame, bulk head, longerons
b) Bulkhead, stringers,
longerons
c) Formers, frame assembly and bulkhead
d) Longerons, stringers
and frames
36. In true monocoque construction primary stresses is taken by
a) Skin
b) Frames
c) Bulkhead
d)
Longerons
37. A semi monocoque construction fuselage is made of
a) Bulkhead and frame
b) Frame, longerons and stringer
c) Bulkhead, frame, longerons & stringers
d) Bulkhead, frame &
formers
38. The skin of semi monocoque fuselage carries
a) No load
b) Full load
c) Part of the load
the load

d) Half of

39. The cabin, flight compartment and baggage compartment are


incorporated into a sealed unit to hold air pressure
a) More than atmosphere pressure
b) Less than atmosphere
pressure
c) Equal to atmosphere pressure
d) None of these
40. To check the cabin for air tightness is called
a) Cabin static pressure test
b) Cabin dynamic pressure
test
c) Leak check
d) All of these
41. An object demonstrates positive dynamic stability if the amplitude
of motion
a) Decreases with time
b) Increases with time
c) Neither increases nor decreases
d) None of these
42. The angle between the chord of the tail plane and the chord of the
main plane is known as
a) Lateral dihedral
b) Longitudinal dihedral
c) Normal dihedral
d) Vertical dihedral
43. The longitudinal stability of aeroplane is dependent on
a) Position of C of G
b) Movement of C of P on the main plane
and fuselage
c) Area of the tale plane, its aspect ratio, distance from C of G
d) All of these
44. Mark the correct statement for horizontal stabilizer
a) It always produces nose up pitching moment
b) It always produces nose down pitching moment
c) Either a) or b) depending upon the design
d) Provides no pitching moment
45. Slip or side slipping refers to any motion of the Aircraft
a) Towards upper wing
b) To downward
c) Towards the lower wing
d) All of these
46. Rotating the control wheel clockwise will move
a) The right aileron upward
b) The right aileron downward
c) As in a) & flight spoiler on right wing up
d) As in a) &
flight spoiler on left wing up

47. At high speed flight, to avoid excessively large rolling moments or


unacceptable structural loading or wing twist, devices used are
a) Flaps
b) Slots
c) Outboard ailerons
d) Inboard ailerons
48. The principal surface contributing to the lateral stability of an
Aircraft is
a) Side surfaces b) The fuselage c) Tail plane
d) None of
these
49. Dihedral angle on the main planes provide with
a) Longitudinal stability
b) Dynamic stability
c) Lateral stability
d) Horizontal stability
50. Aft moment of the control stick will cause
a) Both elevators to move up
elevators to move down
c) Left elevator will move up and right will move down
Movement of horizontal stabilizer

b) Both
d)

51. Minimising the expression


Y=A B C + A B C D + A B C D E + A B + A B C D E + A the output is
a) Y=A
b) Y=1
c) Y=A+ AB
d) Y=AB
52. Y= (5, 15, 23, 29, 37, 47, 55, 61) + X (7, 13, 21, 31, 39, 45,
53, 63)
a) Y=EF
b) Y= AB
c) Y=CD + EF
d) Y=BD
53. In excess 3 codes, BCD 1001 will be written as
a) 9
b) 1011
c) 1100
d) 1001
54. If active low output is required for checking odd parity we will use
a) AND gate
b) OR gate
c) XOR gate
d)
XNOR gate
55. Which series of ICs is used for military purpose?
a) 7400 series
b) 74H00 series c) 5400 series
L S 00 series

d) 74

56. If a demultiplexer is converted into decoder, to get output high on


required output lines, we will tie date line to
a) OV
b) Ground
c) Either a) or b) d) +VCC
57. Which of the following relation is correct?

a) Vo=AdVd[1+(1/CMRR) Vc/Vd]
Vd/Vc]
c) Vo=AdVd[1+CMRR . Vc/Vd]

b) Vo=AcVc[1+(1/CMRR)
a) Vo=AdVd[1+(1/CMRR) Vd/Vc]

58. Due to which action, flip flop act as memory unit


a) Feedback action
b) Amplifying action
c) Oscillating action
d) All of these
59. In RS flip flop R=O, S=1 then action of flip flop is
a) Reset
b) Set
c) No change
Forbidden

d)

60. In D flip flop, the input to S & R terminals will be


a) S=R
b) R=S
c) Both of these
d) None of above
61. Operating frequency of marker beacon is
a) 108.10 MHz to 111.95 MHz
b) 328.6 MHz to 335.4 MHz
c) 100 MHz fixed
d) 75 MHz fixed
62. The facilities provided by a localiser is
a) Give indication of correct descending angle
b) Distance from touch down point
c) Indication of lateral deviation with respect to centre line of runway
d) None of these
63. The correct descending angle is approximately
a) 1 degree
b) 2 degrees
c) 2.25 degrees
degrees

d) 2.75

64. The flag appears at the end of ILS indicator, indicates


a) Reading is correct
b) Partially correct
c) Incorrect & misleading
d) None
65. The middle marker carrier is modulated on
a) 3000Hz
b) 1300Hz
c) 400Hz

d) 4000Hz

66. Typical airborne installation of GPS is carried out by


a) ARINC 249
b) ARINC 429
c) ARINC 629
d) Both b) & c)
67. How many GPS satellites are required to locate an aircraft?
a) 1
b) 2
c) Minimum 3
d)
Minimum 4

68. The control segment of GPS consists of


a) A ground station
b) Various ground based monitoring
stations
c) A master control station
d) Both b) & c)
69. Basically, GPS consists of
a) One independent segment
c) Three independent segment
segment

b) Two independent segment


d) Four independent

70. The purpose of weather radar is


a) To enable the pilot to look ahead to see if dangerous weather exist
b) To inform pilot of pleasant weather
c) To inform about clouds
d) None of these
71. The Tension of brushes to provide brush pressure is approx.
a) 6 Psi
b) 8 Psi
c) 10 Psi
d) 12 Psi
72. A four pole generator will have
a) 2 interpole b) 4 interpole
interpole

c) 6 interpole

d) 8

73. In a 3 phase system, the phase winding is spaced symmetrically so


that the voltage induced is
a) 90o apart
b) 120o apart
c) 60o apart
d)
180o apart

74. To avoid armature reaction of small DC generator (1000 watt or


less) type. The method
used is
a) Interpole Method b) Brush setting method
c) both (a) & (b)
d) None of these
75. Compensating winding is used in series with interpole winding to
a) Increase he life of brushes
b) Distortion of field
c) Reduces
radio interference
d) All the above
76. Staggering slots are used in armature of a DC generator to
a) Minimise ripple voltage
b) Maintain constant output
c) Minimise eddy Current loss
d) None of these above

77. A 3 four pole alternator, running at 6000 rpm will have frequency
of
a) 100 c/s
b) 200 c/s
c) 300 c/s
d) 400 c/s
78. While installing battery (Ni-Cad) on a/c you must inspect
a) Ventilation system of a/c
b) Cable for chaffing
c) Quick disconnection mechanism
d) All of these
79. What will be value of resistance of yellow, red, orange and gold
a) 42000 10%
b) 42000 5% c) 12000 5% d) 22000
10%
80. AC generator works on the principle of
a) Faradays law of electro-magnetic induction b) Mutual induction
c) Self induction
d) All of these

PAPER - II
PART V
1. C
6. C
11. A
16. D
21. A
26. B
31. B
36. A
41. A
46. C
51. B
56. D
61. D
66. D
71. A
76. A

2. A
7. B
12. C
17. B
22. B
27. B
32. A
37. C
42. B
47. D
52. D
57. A
62. C
67. C
72. B
77. B

3. D
8. C
13. C
18. B
23. A
28. B
33. C
38. C
43. D
48. A
53. C
58. A
63. D
68. D
73. B
78. D

4. A
9. D
14. A
19. C
24. B
29. B
34. B
39. A
44. C
49. C
54. D
59. B
64. C
69. C
74. C
79. B

5. B
10. C
15. B
20. D
25. C
30. D
35. C
40. B
45. C
50. A
55. C
60. C
65. B
70. A
75. D
80. A

PAPER - II
PART VI
1. Choose the correct sets of angles of set square of one piece
a) 450 x 300
b) 300 x 900
c) 450 x 600
d) 600 x 600
2. Phantom line is used for indicating the _________ position of part
a) Actual
b) Hidden
c) Relative
d) None of
these
3. Mark the correct statement
a) The arrow head length is equal to double of its width
b) The arrow head length is equal to triple of its width
c) The arrow head length is equal to its width
d) None of these
4. Top view false on the
a) Horizontal plane
c) Half in horizontal and half in Vertical plane
be possible

b) Vertical plane
d) All above cases may

5. Direction of rotation of external gears are


a) Opposite
b) Same
c) Either a) or b)
d) None of the above
6. S in Al-alloy designation indicates
a) Cast alloy
b) Wrought alloy c) As in b) and used for a/c
structure
d) None
7. Which Al-alloy is more corrosion resistant?
a) 2 S
b) 3 S
c) 17 S
d) 52 S
8. Al clad is generally of
a) 17 S & 24 S
b) 24 S & 52 S
d) 53 S & 62 S

c) 52 S & 53 S

9. Inter-crystalline corrosion is generally occurred in


a) Al-alloy containing copper composition
b) 17 S
S
d) All of these

c) 24

10. Which of the following material is used for spot welding?


a) Clad alloys
b) 52 S Al-alloy
c) Both a) & b)
None of these
11. Natural rubber is a polymer of
a) Isoprene
b) Neoprene
these

c) Diprene

d)

d) None of

12. Which material is used for increasing the hardness of natural


rubber?
a) Sulpher
b) Phosphorus
c) Sodium
d) Carbon
13. Which is the basic colour of commercial BUNA-S
a) White
b) Black
c) Red

d) Green

14. GR-A is a known as BUNA-N, in which A stands for


a) Butadiene
b) Acrylonitrile
c) Monovinyl
d) Nitrile
15. Neoprene is designated as GR-M, in which M is stands
a) Monovinyl
b) Chloroprene
c) Acrylonitrile
d) Styrene
16. GR-I designated for which type of rubber
a) Neoprene
b) BUNA-S
c) BUNA-N

d) Butyl

17. Which type of properties is introduced in rubber after vulcanising


process?
a) Elasticity
b) Strong ness
c) Reduce the tackiness
d) All of these
18. A/C rivets are identified by
a) Head Style
b) Alloy
d) All of these

c) Length & Diameter

19. For accurate location of particular area on an a/c, which of the


following is necessary?
a) Water line
b) Butt line
c) As in a) & b) in conjunction with
station line d) None
20. Which type of corrosion is occurred in stainless steel after electric
arc welding?
a) Pitting
b) Galvanic
c) Inter crystalline
d)
Fretting

21. Which is most suitable for spot welding, in stainless steel?


a) Low-voltage
b) High-amperage
c) Low-voltage and High-amperage
d) High-voltage and Lowamperage
22. Which of the following is the Non-Magnetic?
a) Inconel
b) K-Monel
c) Monel
23. SAE 13XX represents
a) Magnesium Steel
d) Chromium Steel

b) Manganese Steel

d) All of these
c) Silicon Steel

24. Hot piece of metal is increased in thickness and decreased in


length
a) Upsetting
b) Down setting
c) Swaging
d)
Rolling
25. Which of the following have greatest tensile strength?
a) Fibreglass
b) Aramid
c) Carbon
d) Ceramic
26. For flight equilibrium, designer tries to fix the CG
a) and C of P together
b) At rear of C of P
c) In front of most forward position of CP
d) Along aerodynamic
C of P
27. Flight calculations are based on the magnitude and direction of
a) Lift & drag
b) Weight & thrust
c) Lift & thrust
d) Both a) & b)
28. The factors limiting the aspect ratio are
a) Structural consideration
b) Drag consideration
c) Lift consideration
d) Both a) & b)
29. What is required to reduce the landing speed?
a) A low minimum drag coefficient
b) A small movement of C of
P
c) A high max CL
d) A high value of CL3/2/CD
30. With increase in altitude pressure & temperature
a) Drops
b) Will rise
c) Pressure drops, temperature increases
d) Temperature drops,
pressure increases

31. The disadvantage of vacuum operated Gyro is


a) At high altitude, stability is reduced due to decrease in atmospheric
pressure.
b) Weight due to pipelines
c) Possibility of contamination by corrosion and dirt particles.
d) All of these

32. Gyro of AC operated instruments utilize the principle of squirrel


cage induction motor and because of high frequency of power supply,
greater rotor speeds are possible of approximate.
a) 23000rpm
b) 24000rpm
c) 24500rpm
d) None
33. Indication of pitch & Bank attitude are presented by the relative
position of
a) Aircraft symbol
b) Gyro stabilised bar (Horizon
symbol)
c) Both a) & b)
d) None of these
34. Freedom of gimbal system movement about the roll & pitch axes in
gyro horizon is ______ respectively
a) 3600 and 900 b) 3600 and 800 c) 3600 and 850 d) None
35. The reason for restricting pitch movement of gyro horizon is to
prevent
a) Gimbal error b) Gimbal lock
c) Transport wander
d)
None
36. In single disk break, break linings are known as
a) Pucks
b) Three are fix
c) Three are movable
above

d) All

37. When break pressure is released piston moves back to position


with the
a) Return spring force b) Hydraulic pressure
c) Adjusting pin
d) None
38. To check the angle of the main structural component in relation to
the longitudinal and lateral axis is known as
a) Incidence check
b) Dihedral check c) Structural alignment check
d) Verticality check

39. On copper and copper alloy corrosion forms on the surface as


a) White powder b) Greenish film
c) Blue
d)
Black
40. Corrosion on the metal is due to
a) Chemical attack
b) Electro chemical attack
& b) d) None

c) Both a)

41. During routine check, the fuselage should be inspected for


a) Corrosion
b) Fretting
c) Spilage
d) All of
these
42. The truss type fuselage is covered by
a) Steel sheet
b) Al alloy sheet c) Fabric
these

d) All of

43. Thermoplastic material is originally


a) Hard
b) Soft and pliable when
exposed to heat
c) It retains the moulded shape when cooled
d) All of these
44. Remoulding and reshaping cannot be done on
a) Thermosetting plastic
b) Thermoplastic c) Both a) & b)
None of these

d)

45. Plastic should be stored in bins which are tilted at


a) 200
b) 100
c) 150
250

d)

46. The operating frequency of ADF is


a) 90Hz
b) 90KHz
c) 150Hz
1800KHz
47. The ADF operates on
a) LF Band
b) MF Band
Band

c) LF & MF Band

d) 90KHz to

d) VHF

48. In ADF antenna system at a point signal fades out this is called
a) Null position
b) Figure of eight
c) Cardiod d) None of
these
49. ADF receiver essentially is
a) TRF receiver b) Superhetrodyne receiver
superhetrodyne receiver
d) Suppressed carrier receiver

c) Double

50. Types of antenna / antennas used for ADF receiver


a) Half wave
b) Full wave
c) Sense aerial
d) As in c) and loop aerial
51. If a D flip-flop is to switch from 0 to 1, then input is to be kept
high for at least time T where
a) T= t setup + t hold
b) T= t setup + t hold
+ t propagation delay
c) T= t setup + t hold - t propagation delay
d) T= clock
period
52. JK Flip flop is dividing the input frequency by 2, then its condition
is
a) J=0, K=0
b) J=0, K=1
c) J=1, K=0
d) J=1, K=1
53. In decimal to BCD decoder
a) 1 input, 10 output
c) 4 input, 10 output

b) 10 input, 4 output
d) 10 input, 1 output

54. If SUB pin is high in a Adder-subtractor circuit, then circuit is;


a) Adding Two bytes
b) Subtracting input byte
from output
c) Subtracting output byte from input
d) Adding 2s complement
byte to the other byte
55. One of the effect of negative feed back in amplifiers is to
a) Increase the noise
b) Increase the harmonic
distortion
c) Decrease the bandwidth
d) Decrease the harmonic
distortion
56. The relationship between back emf and applied voltage in case of a
dc motor is given by
a) Eb = V + Ia Ra
b) Eb = V Ia Ra
c) Eb = V
d) None of these
57. The direction of rotation of dc motor can be determined by
a) Flemings right hand rule
b) Flemings left hand rule
c) Lenzs law
d) Amperes law
58. An engine driven 50 Hz alternator has a speed of 750 rpm. How
many poles it has?
a) 6 poles
b) 4 poles
c) 2 poles
d) 8 poles

59. The frequency of emf generated by a generator depends upon its


a) Speed
b) No. of ploles c) Machine rating
d) Both a)
& b)
60. Two quantities are said to be in phase with each other when
a) The phase difference between two quantities is zero degrees
b) Each of them pass through zero values at the same time and rise in
the same direction
c) Both a) & b)
d) None of these
61. Capacity of a capacitor depends upon
a) Separation between the plates
b) Area of plates
c) Di-electric material
d) All of these
62. The device used to measure very high insulation resistance of
electric cable is
a) High resistance voltmeter
b) Megger / Insulation
resistance tester
c) Iron vane meter
d) Ammeter of high range
63. If six cells are connected in series of each E volts, the total voltage
of the battery will be
a) 6E
b) 3E
c) 4E
d) 12E
64. Special test equipment comprising a meter and two cables each of
specific length, is required for checking the resistance of bonding. A
meter widely used , consists of an ohm-meter operating on
a) Principle of current ratio
b) Principle of voltage ratio
c) None of these
65. Cell phone is used to protect the Ni-Cad battery from
a) Shorting between plates
b) Thermal runaway
c) Avoid leakage of electrolyte
d) All of these
66. Which material you select for riveting Ni-steel sheet
a) Monel
b) 2017-T
c) 2024-T6
d) Mild steel
67. Which one of the following rivet is ready for use as received and
need no further heat treatment
a) 2117
b) 2017-T
c) 2024
d) 1100
68. Ice-Box rivets are
a) 2017-T
b) 2117-T

c) 2024-T

d) Both a) & c)

69. The specification for universal head rivet


a) AN-470
b) MS-20613
c) MS-20615
of these

d) All

70. Part No AN 470 B 3-8, indicates


a) Shank dia is 3/16
b) Rivet length is 8/32
c) Material is 5056-Al alloy
d) All of the above
71. Fluid used in the Aircraft hydraulic systems are
a) Vegetable
b) Mineral
c) Synthetic
d) All
of these
72. With pure rubber seals and hose oil used in the system is
a) Mineral
b) Vegetable
c) Synthetic
of these

d) All

73. In open centre system, the number of services can be operated at


one time is
a) One only
b) Two only
c) Any number
d) All of these
74. In closed system where fixed volume pump is fitted, the system is
fitted with
a) Automatic cut out value to divert pump output to reservoir
b) To maintain the normal built up pressure
c) Both a) & b)
d) None of these
75. Pressure maintaining value fitted in the system is for
a) To maintain the normal system pressure
b) To safe guard the operation of the important services
c) To maintain the pressure in primary services at a value suitable for
operation of services
d) Both b) & c)
76. Packing is made of
a) Asbestos
b) Cork
d) Felt

c) Synthetic or natural rubber

77. Aviation gasoline is having relative density of


a) 0.70
b) 0.72
c) 0.80
d) 0.5
78. Re-fuller delivery line should have filter of
a) 5 microns
b) 8 microns
c) 4 microns
d) 10 microns

79. Component fitted in pressurization system to limit any possible


negative differentiate pressure to a sage value is
a) Safety value b) Outflow value c) Inward relief value
d)
pressure controller.
80. Roots type blower pressurized and send air to cabin duct by taking
a) Ram air
b) Air from exhaust
c) Bleed air
d)None of these

PAPER - II
PART VI
1. B
6. C
11. A
16. D
21. C
26. C
31. D
36. D
41. D
46. D
51. A
56. B
61. D
66. A
71. D
76. C

2. B
7. A
12. A
17. D
22. B
27. D
32. B
37. A
42. C
47. C
52. D
57. B
62. B
67. A
72. B
77. B

3. B
8. A
13. B
18. D
23. B
28. D
33. C
38. C
43. D
48. A
53. B
58. D
63. A
68. D
73. A
78. A

4. A
9. D
14. B
19. C
24. A
29. C
34. C
39. B
44. A
49. B
54. D
59. D
64. A
69. D
74. C
79. C

5. A
10. C
15. A
20. C
25. B
30. A
35. B
40. C
45. B
50. D
55. D
60. C
65. B
70. C
75. D
80. A

PAPER - II
PART VII
1. Duckbill plier
a) Is a flat nose plier
c) Have serrations on their jaws

b) Is used for twisting safety wires


d) All are correct

2. Needle nose pliers are used for


a) Extracting thin/sharp components
nails
c) Gripping small electronic components

b) Extracting
d) All are correct

3. i) A chisel can never cut the material all by itself


ii) A die is a cutting tool
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
4. Cutting edge of a chisel is generally ground to an angle of
a) 30 degrees
b) 70 degrees
c) 90 degrees
d) 110 degrees
5. Various types of cut of a file are
a) Single cut
b) Smooth cut
c) Rasp
d) Both a) & b) are correct
6. Bearing strength of a material refers to
a) Direct tensile load it can bear
b) Resistance to tear at the point of applied load
c) Resistance to fracture at the point of applied load
d) Resistance to shear
7. Characteristics of metals relating to drawing it into wire is
a) Tensile strength
b) Malleability
c) Ductility
d) Brittleness
8. Fusibility of a metal refer to its property that permits
a) Welding
b) Drawing into thin sheets
c) Drawing into wires
d) Good thermal conductivity
9. Aluminium alloy 1100 implies
a) Pure aluminium
c) It contains 111% zinc

b) It contains 11% copper


d) Heat treated alloy

10. Clad aluminium alloys are used in aircraft. They are

a) Lighter than other aluminium alloys


b) Stronger than unclad aluminium alloys
c) Easily heat treatable
d) Less susceptible to corrosion
11. Medium carbon steels have a carbon percentage of
a) 0.1 0.3
b) 0.3 0.5
c) 0.5 1.0
d) 1.0 2.0
12. Which of the statement is correct?
a) Both heat treatable & non heat treatable aluminium alloys can be
strain hardened
b) Strain hardening is same as cold working
c) Strength & hardness increases during cold working
d) All are correct
13. Find out the wrong statement regarding titanium
a) It is highly corrosion resistant
b) It maintain strength at elevated
temperatures
c) It has good resistance to creep d) It is magnetic
14. Pitot static system have heating elements to
a) Remove moisture from the air
b) Prevent ice formation
c) To permit flying at high altitude
d) All are correct
15. Pressure heads of pitot static system should not be painted,
because it
a) Impairs their thermal efficiency
b) May cause obstruction of
orifices
c) None of the above
d) Both a) and b) are correct
16. i. In cross filing, the file is moved length wise across the work
ii. In draw filing, the file is moved side wise across the work
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct
17. A cross cut saw has
a) 4-6 teeth per inch
c) 10-15 teeth per inch

b) 6-12 teeth per inch


d) 12-18 teeth per inch

18. i) For a good cut on a hard material, a blade with more teeth
should be used
ii) While cutting a tube, a blade should be so chosen that at least five
teeth are there on each side of the tube as it is cut
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is correct

19. Spiral anger bit for drilling holes in wood are


a) Generally 7-10 inches long
b) - one inch in diameter
c) Used only with a bow type hand brace d) All are correct
20. Screw driver used when there is no clearance for normal screw
driver is called
a) Closed area screw driver
b) Stubby screw driver
c) Off set slot screw driver
d) Any one of the above
21. Air driven power screw driver should be used
a) For large diameter screw
b) For removing screw that are jammed
c) Where large number of screws are to be removed and fitted back
d) When removing screws from harder material
22. With regard to wrenches, find out the incorrect statement
a) These are made from chrome vanadium steel
b) These are generally die cast
c) Wrenches are made in various shapes & sizes
d) These are plated to improve their appearance
23. Box end wrenches are used
a) To loosen nuts that are exceptionally light
b) Where there is restricted space
c) For nuts that are bigger than one inch size
d) When open end wrench is not available
24. Crowfoot socket wrench is used where the following cannot be
used
a) Open end wrench
b) Box end wrench
c) Standard socket wrench
d) All are correct
25. SAE 2340 is
a) Chromium steel with 3% chromium
b) Nickel chromium steel with 0.3% carbon
c) Nickel steel with 3% Nickel & 0.4% carbon
d) Carbon (0.4%) steel
26. During nitric acid test, if the material shows strongly magnetic
nature, then it is
a) Monel metal
b) Carbon steel
c) Nickel steel
d) 18-8 steel

27. Weldability is poorest in case of


a) Plain carbon steel
b) Low carbon steel
c) High carbon steel
d) Wrought iron
28. Stainless steel is corrosion resistance due to presence of
a) Silicon
b) Cobalt
c) Chromium
d) Manganese
29. L shaped channels are produced by
a) Forging
b) Extrusion
c) Machining
d) Casting
30. Creep in metals is
a) Elongation due to temperature
b) Temporary elongation due to temperature and stresses
c) Permanent set due to stresses and high temperature operation
d) All are correct
31. Angular momentum is
a) Moment of inertia
b) Angular velocity
c) Product of a) & b)
d) Sum of a) & b)
32. Mark the incorrect statement
a) Precession is inversely proportional to the strength & direction of
applied force.
b) Precession is inversely proportional to the moment of inertia of the
rotor.
c) Precession is inversely proportional to the angular velocity of the
rotor.
d) None of the above
33. Control of drift, relating to horizontal gyroscopes can be achieved
by:
a) Calculating corrections using earth rate formula and applying them
as appropriate
b) Applying fixed torques & cause gyro to process at a rate equal &
opposite to the earth rate.
c) As in b) but which can be varied according to latitude
d) All of these
34. When gimbal orientation is such that the spin axis becomes
coincident with one or the other of the axes of freedom which serves
as attitude displacement reference is termed as
a) Gimbal lock
b) Gimbal Error c) Apparent drift

35. Grip length of the bolt is


a) Total length of the bolt
b) Plain shank length of the
bolt
c) Length under the head to the end of the bolt
d) None of these
36. In close tolerance bolt, force applied to drive in is
a) 10 ounce hammer
b) 20 ounce hammer
c) 12 to 14 ounce hammer
d) Sledge hammer

37. Special washer AC 950 and AC 955 are used where


a) Bolt is installed at angle to surface
b) Bolt is installed head
down
c) It can be used any where
d) None of these
38. Rasp file is used for
a) Hard material
b) Lead, wood or leather
c) Both a) & b)
d) Other materials except lead, wood & leather
39. Philips screwdrivers are tapered to an angle of
a) 730
b) 530
c) 600
0
93

d)

40. Snaps are used to


a) Support the markers head of rivets
b) To make the shop
head during riveting
c) Both a) & b)
d) None of these
41. Soft solder is the combination of tin and lead in proportion of
a) 2 : 3
b) 3 : 2
c) 1 : 4
d) 4 : 1
42. Bending stress is the combination of
a) Compression and shear
b) Shear and tension
c) Compression and tension
d) Tension and shear
43. In true monocoque construction primary stresses is taken by
a) Skin
b) Frames
c) Bulkhead
d)
Longerons
44. The skin of semi monocoque fuselage carries
a) No load
b) Full load
c) Part of the load
the load

d) Half of

45. The longitudinal stability of aeroplane is dependent on


a) Position of C of G
b) Movement of C of P on the main plane
and fuselage
c) Area of the tale plane, its aspect ratio, distance from C of G
d) All of these
46. Direction of rotation of external gears are
a) Opposite
b) Same
c) Either a) or b)
d) None of the above
47. Al clad is generally of
a) 17 S & 24 S
b) 24 S & 52 S
d) 53 S & 62 S
48. Natural rubber is a polymer of
a) Isoprene
b) Neoprene
these

c) 52 S & 53 S

c) Diprene

49. Which is the basic colour of commercial BUNA-S


a) White
b) Black
c) Red

d) None of

d) Green

50. Which type of corrosion is occurred in stainless steel after electric


arc welding?
a) Pitting
b) Galvanic
c) Inter crystalline
d)
Fretting
51. SAE 13XX represents
a) Magnesium Steel
b) Manganese Steel
c) Silicon Steel
d) Chromium Steel
52. Hot piece of metal is increased in thickness and decreased in
length
a) Upsetting
b) Down setting
c) Swaging
d)
Rolling
53. The factors limiting the aspect ratio are
a) Structural consideration
b) Drag consideration
c) Lift consideration
d) Both a) & b)
54. The disadvantage of vacuum operated Gyro is
a) At high altitude, stability is reduced due to decrease in atmospheric
pressure.
b) Weight due to pipelines
c) Possibility of contamination by corrosion and dirt particles.
d) All of these

55. Gyro of AC operated instruments utilize the principle of squirrel


cage induction motor and because of high frequency of power supply,
greater rotor speeds are possible of approximate.
a) 23000rpm
b) 24000rpm
c) 24500rpm
d) None
56. During routine check, the fuselage should be inspected for
a) Corrosion
b) Fretting
c) Spilage
d) All of
these
57. The truss type fuselage is covered by
a) Steel sheet
b) Al alloy sheet c) Fabric
these

d) All of

58. Two quantities are said to be in phase with each other when
a) The phase difference between two quantities is zero degrees
b) Each of them pass through zero values at the same time and rise in
the same direction
c) Both a) & b)
d) None of these
59. If six cells are connected in series of each E volts, the total voltage
of the battery will be
a) 6E
b) 3E
c) 4E
d) 12E
60. Which one of the following rivet is ready for use as received and
need no further heat treatment
a) 2117
b) 2017-T
c) 2024
d) 1100
61. When calculating power in a reactive or inductive ac circuit, the
true power is
a) More than the apparent power
b) Less
than the apparent power
c) As in b) in reactive circuit and as in a) in inductive circuit
d)
None of these
62. The correct way to connect a test voltmeter in a circuit is
a) In series with the unit
b) Between the source
voltage and the load
c) In parallel with the unit
63. Transfer of electrical energy from one conductor to another without
the add of electrical connections
a) is called induction
b) is called air gap transfer

c) Will cause excessive arching and heat, and as a result is impractical


64. Diodes are used in electrical power circuit primarily as
a) Switches
b) Rectifiers
c) Relays
d)
Contactors
65. If three resistors of 3, 5 and 22 ohms are connected in series in a
28V circuit, how much current will flow through the 3 ohms resistor?
a) 9.3 amps
b) 1.05 amps
c) 0.93 amps
d) 10.05 amps
66. What is the value of a resistance if given colour codes as brown,
black, brown, black and brown.
a) 1010 ohms
b) 1000 ohms
c) 101 ohms
d) 10.1 K ohms
67. What is the value of a capacitor if given colour codes are orange,
orange, blue and white.
a) 33nF
b) 33F
c) 33pF
d) 3300F
68. The output of a astable multi-vibrator is
a) Triangular wave
b) Saw tooth wave
Sinusoidal wave
d) Square wave

c)

69. In an oscilloscope by varying intensity control, what actually varied


internally?
a) Cathode voltage
b) Anode voltage
c) Grid voltage
d) Cathode current
70. The output of NOT gate is always
a) High
b) Low
d) Complementary of input

c) Same as input

71. Oxy acetylene welding process is suitable for joining metal sheets
and plates having thickness of
a) 1 to 30mm
b) 2 to 50 mm
c) 2 to 40mm
d) All of these
72. In oxyacetylene welding, welding rod is required as a filter metal
when welding is carried out above
a) 15mm
b) 10mm
c) 40mm
d) 5mm
73. In oxyacetylene welding, neutral flame produces a maximum
temperature of
a) 30000F
b) 32000F
c) 32000C
d) 30000C

74. Standard colour for oxygen hose is


a) Black
b) Red
these

c) Green

d) None of

75. In magnet steel, the alloying elements are


a) Nickel, Cobalt
b) Silicon, Nickel
c) Molybdenum, Copper
d) Tungsten, Cobalt
76. Maximum distance between support for fluid tubing of 1/8 size of
steel is
a) 12
b) 14
c) 9.5
d) 11.5
77. MS 20004 is a
a) Internal wrenching bolt
c) Clevis bolt

b) Close tolerance bolt


d) None of these

78. Mark the incorrect statement, regarding K monel metal


a) It is ferrous alloy
b) It is used for gears and
chain
c) It is non ferrous alloy
d) It is corrosion resistant
79. The symbol is for
a) Wood
c) Steel

b) Cast iron
d) Rubber

80. Ballast is used on a/c


a) To attain the desired c.g.
making nose heavy

b) To increase the weightc) For


d) None of these

PAPER - II
PART VII
1. D
6. B
11. B
16. C
21. C
26. B
31. C
36. C
41. B
46. A
51. B
56. D
61. B
66. C
71. B
76. D

2. C
7. C
12. D
17. B
22. B
27. C
32. A
37. A
42. C
47. A
52. A
57. C
62. C
67. B
72. A
77. A

3. C
8. A
13. D
18. A
23. A
28. C
33. D
38. B
43. A
48. A
53. D
58. C
63. A
68. D
73. C
78. A

4. B
9. A
14. B
19. D
24. D
29. B
34. A
39. B
44. C
49. B
54. D
59. A
64. B
69. C
74. C
79. B

5. A
10. D
15. D
20. C
25. C
30. C
35. B
40. B
45. D
50. C
55. B
60. A
65. C
70. D
75. D
80. A

PAPER - II
PART VIII
1. Which of these is indicator of elasticity & plasticity both?
a) Rockwell hardness test
b) Brinell hardness test
c) Shore Scleroscope
d) Vickers hardness test
2. Flattening test is
a) Bending test b) Only for copper wires
d) Both a) & c)

c) For tube testing

3. Max rate of bending per minute in reverse bend test is


a) 50
b) 60
c) 10
d) 40
4. Izod test measures
a) Toughness
b) Height of upswing
breaking
d) Hardness

c) Energy in

5. Fatigue test is for determining


a) Stress in material
b) Strain in rod
c) Stress limit for material
d) Elongation of wire
6. Torsion test is essential for
a) Wires
b) Tube
7. Bending test indicates
a) Ductility
b) Brittleness
Density

c) Rods

d) Sheet

c) Hardness

8. 250 HB 10 indicates
a) Strength only b) Hardness only c) Both a) & b)
9. Unit of tension is
a) N
b) N/m

c) KN/m2

d)

d) Toughness
d) Kg/cm2

10. First usable ferrous product obtained by smelting ores in a blast


furnace is
a) Pig Iron
b) Wrought Iron
c) Cast Iron
d) Steel
11. Siderite is
a) Oxide ore of Iron
Iron
c) Sulphide ore of Iron

b) Carbonate ore of
d) Flux used in furnace

12. Coke used in blast furnace is


a) Fuel
c) Reducing agent
agent
13. In upper reduction zone, we get
a) Iron
c) Carbon monoxide
14. Steel is alloyed to improve
a) Hardenability
c) Fatigue strength
15. Cast Iron sparks are
a) Red
c) Straw coloured
coloured

b) Flux
d) Both fuel & reducing

b) Carbon dioxide
d) Both Fe & CO2
b) Toughness
d) All of the above
b) White
d) First Red then Straw

16. Corrosion resistant steel used in Aircraft construction is


a) 18 8 steel
b) Medium carbon steel
c) 18 6 steel
d) Silicon steel
. Major alloying elements of stainless steel are ( in order of %
composition)
a) Ni Cr
b) Ni V
c) W Ni
d) Cr Ni
18. Forging steel is
a) Low Carbon steel
steel
c) High Carbon steel
19. Exhaust collector is made up of
a) Silicon steel
c) Chromium steel

b) Medium Carbon
d) Either a) or c)
b) Titanium steel
d) Ni Cr steel

20. Which element is responsible for Red hardness property?


a) Ti
b) Ta
c) Mo
d) W
21. Which elements are responsible for Penetration hardness?
a) Mn, S
b) Mn, P
c) Mn, Cr
d) Cr, C
22. Stainless steel is
a) Ni Cr steel b) Cr Mo steel c) Ni W steel

d) Cr Va steel

23. Silicon in steel acts as


a) Oxidiser
b) Deoxidiser
& c)

c) Impurity

d) Both b)

24. Mark the correct statement


a) SAE 2330 is chromium steel
b) SAE 3250 is used in making axle shafts because of high strength
c) SAE 3115 is used for making piston pins, cam rings
25. Steel is preheated before welding to
a) Include strength
b) Enhance its creep resistance
c) Enhance its creep resistance
26. Steel used for wing-hinge fittings & flying wire trunnions is
a) SAE 4140
b) SAE 6150
c) SAE
1015
27. Steel used commercially for automatic machine production is
a) SAE 4135
b) SAE 4615
c) SAE
6115
28. Steel used as an alternate for SAE 4130 steel is
a) SAE 8620
b) SAE 8630
c) SAE
9260
29. Pyrometer is used to
a) Measure the temperature
c) Give protective atmosphere

b) Protect the furnace

30. The fastest rate of cooling is given by


a) Brine
b) Oil

c) Water

31. The tip of the rivet is upset to form a second head and that is
known as
a) Round head
b) Shop head
c) Flat head
d)
Brazier head
32. O ring packings are used for preventing
a) Internal leak b) External leak c) One direction leak
d) Both a) & b)
33. Gaskets are made of
a) Asbestos
b) Copper
these

c) Cork

d) All of

34. While bending tubing, a small flattening is allowed but the small
diameter of the bend should not be less than _______ of the outside
diameter
a) 90%
b) 25%
c) 75%
d) 80%
35. Deep permanent impression in the hose produced by the pressure
of hose clamp is known as
a) Hot flow
b) Deep flow
c) Cold flow
d) None of
these
36. In hex bolt, the length is measured
a) Under the head to the end of the bolt
shank
c) Total length

b) Plain portion of the


d) Threaded length

37. Aircraft bolts are made of


a) Mild steel
b) Stainless steel
c) Aluminum alloy
d) Cadmium plated nickel steel corrosion resistance steel and
aluminum alloy
38. Fluid used in the Aircraft hydraulic systems are
a) Vegetable
b) Mineral
c) Synthetic
of these
39. Vegetable based fluid is normally
a) Pink
b) Yellow
d) None of these

d) All

c) Almost colourless

40. With pure rubber seals and hose oil used in the system is
a) Mineral
b) Vegetable
c) Synthetic
of these

d) All

41. In open centre system, the number of services can be operated at


one time is
a) One only
b) Two only
c) Any number
d) All of these
42. When no services are operated in open centre system, the
pressure value in the system is
a) At low value
b) At high value
c) Pump output passes directly to the reservoir
d) Both a)
& c)

43. In closed system where fixed volume pump is fitted, the system is
fitted with
a) Automatic cut out value to divert pump output to reservoir
b) To maintain the normal built up pressure
c) Both a) & b)
d) None of these
44. Thermal relief value fitted in the hydraulic system operates at a
pressure
a) Slightly higher than normal system pressure
b) Relieve only a small quantity of fluid
c) At lower than the system pressure
d) Both a) & b)
45. Pressure maintaining value fitted in the system is for
a) To maintain the normal system pressure
b) To safe guard the operation of the important services
c) To maintain the pressure in primary services at a value suitable for
operation of services
d) Both b) & c)
46. Restrictor valve fitted in the hydraulic system for
a) Allowing free flow of fluid in one direction
flow in other direction
c) To control the pressure
& b)
47. Packing is made of
a) Asbestos
b) Cork
d) Felt
48. Running seals are
a) Packing
b) Gasket

b) Limited
d) Both a)

c) Synthetic or natural rubber

c) Wiper

d) None of these

49. Washer (gasket) used for spark plug is


a) Asbestos
b) Copper
c) Cork

d) All of these

50. Gasket used on uneven or varying space is made of


a) Asbestos
b) Cork
c) Copper
d) All of these
51. Seals used for cleaning and lubricating is called
a) Wiper
b) Gasket
c) Packing
52. Fuel used for turbo jet engine is
a) Gasoline
b) Aviation kerosene
these

d) None of these

c) Petrol

d) None of

53. Aviation gasoline is having relative density of


a) 0.70
b) 0.72
c) 0.80
d) 0.5
54. Relative density of AVTUR fuel is
a) 0.80
b) Shop head
d) Both a) & b)
d) All of these
c) 75%
c) Cold flow
a) Under the head to the end of the bolt
d) Cadmium plated nickel steel corrosion resistance steel and
aluminum alloy
d) All of these
c) Almost colourless
b) Vegetable
a) One only
c) Pump output passes directly to the reservoir
c) Both a) & b)
d) Both a) & b)
d) Both b) & c)
d) Both
c) Synthetic or natural rubber
a) Packing
b) Copper
b) Cork
a) Wiper
b) Aviation kerosene
b) 0.72
b) 0.75

c) 0.70

d) 0.72

55. Re-fuller delivery line should have filter of


a) 5 microns
b) 8 microns
c) 4 microns
d) 10 microns
56. The source of pressurised air in piston engine aircraft is
a) Compressor
b) Supercharger c) Turbo charger d) Both b)
& c)
57. Component fitted in pressurisation system to limit any possible
negative differentiate pressure to a sage value is
a) Safety value
b) Outflow value c) Inward relief value
d) pressure controller

58. To maintain a free flow of ventilation air within the aircraft when
parked the component is filled to
a) Safety value
b) Ground automatic relief value
c) outflow
value d) Both a) & c)
59. Roots type blower pressurised and send air to cabin duct by taking
a) Ram air
b) Air from exhaust
c) Bleed air
d)
None of these
60. Engine driven cabin compressor which is used on turbo prop
aircraft, its output pressure is controlled
a) Automatically
b) Manually
c) Not controlled
d)
Both a) & b)
61. The working fluid used in reciprocating engine is
a) Solid fuel
b) Oxidizer & Fuel
c) Fuel / Air
Mixture
d) All of these
62. Mark the correct statement
a) Turbo prop engine accelerate large mass of air through small
velocity change
b) As in a) & Piston Engine also accelerate large mass of air through
small velocity change
c) Turbo Jet Engine accelerate large mass of air through small velocity
change
d) Pulse Jet Engine accelerate large mass of air through small velocity
change
63. To compress the engine working fluid, Piston Engine uses
a) Turbine driven compressor
b) Pressure rise
due to combustion
c) Positive displacement, piston type compressor
d) Both a)
& c) are correct
64. Piston engine classified according to
a) Thrust
b) No. of stroke
c) Cylinder arrangement with respect to crank shaft
d) Both b)
& c)
65. Radial engine classified as
a) Upright, inverted
rows
c) Cylinder arranged on cam shaft

b) According to no. of
d) Both a) & c)

66. The emitter resistor RE in a transistor amplifier is bypassed by a


capacitor
a) To reduce the voltage gain
b) To increase the voltage
gain
c) Causes thermal runaway
d) Stabilises the Q point
67. A transistor is operating in the active region. Under this condition
a) Both the junctions are forward-biased
b) Both the junctions are reverse-biased
c) Emitter-base junction is reverse-biased, and collector-base junction
is forward-biased
d) Emitter-base junction is forward-biased, and collector-base junction
is reverse-biased
68. The potential-divider method of biasing is used in amplifier to
a) Limit the input ac signal going to the base
b) Make the
operating point almost independent of
c) Reduce the dc base current
d) Reduce the
cost of the circuit
69. For generating 1 KHz note, the most suitable circuit is
a) Hartley Oscillator
b) Colpits Oscillator
c) Tuned-collector Oscillator
d) Wein-bridge Oscillator
70.To generate a 1 MHz signal the most suitable circuit is
a) Wein-bridge Oscillator
b) Phase shift Oscillator
c) Colpits Oscillator
d) Hartley Oscillator
71. Weather radar works on
a) Echo system
b) LOS system
system
72. Antenna size for DME is
a) 1
b)

c) /4

c) VHF system

d) HF

d) /8

73. EDAS means


a) Electrical and digital Aircraft system
b) Electronics / digital Aircraft system
c) Electronics digital and avionics system
d) None of these
74. The purpose of EDAS is
a) Modernise the various Aircraft system and their display system
b) To reduce the work load of the pilot
c) To reduce the space in the Aircraft
d) All of these

75. The satellites are placed in geo-synchronous orbit for sat com
system and they provide coverage between
a) Longitude 750
b) Between latitude 750
North and South
c) Both a) & b) above
d) None of these
76. In ball type erection unit, rotation of holder takes place through
reduction gear from gyro rotor shaft, the speed of holder
being__________
a) 25 rpm
b) 20 rpm
c) 30 rpm
d) 35 rpm
77. In torque motor and levelling switch type of erection system the
supply fed to the centre electrode is
a) 25V AC
b) 20V AC
c) 12V AC
d) 15V AC
78. Fast Erection system is supplied with
a) 28V DC
b) 115V AC
c) 25V AC

d) None

79. Erection rate of normal erection system is


a) 50/sec
b) 50/min
c) 30/min

d) 30/sec

80. Erection rate of fast erection system is


a) 50/sec
b) 50/min
c) 30/min

d) 30/sec

PAPER - II
PART VIII
1. C
6. A
11. B
16. A
21. C
26. A
31. B
36. A
41. A
46. D
51. A
56. D
61. C
66. D
71. A
76. A

2. D
7. A
12. D
17. D
22. A
27. B
32. D
37. D
42. C
47. C
52. B
57. C
62. B
67. D
72. C
77. B

3. A
8. C
13. D
18. B
23. D
28. B
33. D
38. D
43. C
48. A
53. B
58. B
63. C
68. B
73. B
78. B

4. B
9. A
14. D
19. B
24. B
29. A
34. C
39. C
44. D
49. B
54. A
59. A
64. D
69. D
74. D
79. B

5. C
10. A
15. D
20. D
25. B
30. A
35. C
40. B
45. D
50. B
55. A
60. A
65. B
70. C
75. B
80. D

PAPER - II
PART IX
1. In electromagnetic method of fast erection, the output of secondary
winding of transformer is:
a. 115V AC
b. 20 V AC
c. 28V DC
d. 185V AC
2. For compensation of pendulosity error, the amount of inclination is
governed by value of:
a. 0.50
b. 1.750
c. Either a) or b)
d. None
3. In turn & ship indicator, the precession of gyro is equal to
a) Angular momentum of gyro
b) Rate or turn
c) Product of a) & b)
d) None
4. In TSI, in practice, the gimbal ring deflection is generally not more
than
a) 50
b) 120
c) 80
d) 60
5. Under banked turn in TSI means
a) Skid out of turn
b) Slip into turn

c) None

6. Crank case of a piston engine is made up of:


a) One piece construction
b) Two piece construction
c) Multiple piece construction d) All of the above
7. Crank case provides
a) Attachment of the cylinder
b) Attachment of
propeller
c) Tight enclosure for lubricating oil & a) d) All of the above
8. In radial engine, impeller & blower are found in
a) Power section
b) Nose section
c) Super charger section
d)Accessory section
9. Crank shaft
a) Converts heat energy in propulsive force
b) Converts heat energy in mechanical work
c) Transform reciprocating motion of piston in to rotary motion
d) As in c) & to rotating propeller shaft

10. Double throw crankshaft, also known as


a) 3600 crank shaft
b) 600 crank shaft
0
c) 80 crank shaft
d) 1800 crank shaft
11. Maximum strength of fibres is in which direction of bi-directional
fabric
a) Warp
b) Weft
c) Biased d) Fill
12. Which of the following is the unidirectional fabric style?
a) Mats
b) Tapes
c) Kevlar
c)Fiber glass
13. Which of the following can use as leak tester
a) Ultrasound method (Water immersion method
b) Dyepenetrant method
c) Magnetic particle inspection
d) None of these
14. Elliptical motion of wave on the upper surface of material known as
a) Shear wave
b) Compression wave
c) Surface wave d) Tension wave
15. Thin sheet metals weld defect can be inspected by
a) X-Ray
b) Ultrasonic method
c) Eddy current
d) None of these
16. By which method we cannot detect the inter-granular corrosion
easily
a) Ultrasonic method
b) Eddy current
c) Magnetic particle
d) X-Ray
17. Grinding cracks on small radius bends is appeared as __________
in magnetic particle inspection
a) Irregular lines over affected areab) Short parallel lines
c) Dotted patch
d) Scattered small lines
18. Permeability of material is the function of
a) Magnetising force
c) Both a) and b) are correct

b) Flux density
d) None of these

19. Which instrument is used for checking the surface roughness?


a) Spectrometer b) Prosfetrometer
c) Profilometer
d) Hilsegmetometer
20. The content of CO2 fire extinguisher or N2 pressurized extinguisher
is checked by
a) Weight and pressure gauge
b) Marking on neck

c) By operating the extinguisher

d) All of these

21. Which is incorrect statement?


a) If corrosion is present in control cable should be replaced
b) Cable used in seaplane must be coated with paral-ketone
c) For detection of corrosion, cable twist in same way of lay
d) Carbon steel cable must be used with protective coating
22. After welding aluminium parts flux should be removed by
a) Immersing them in Luke warm water for 30 minutes
b) Mechanical means, i.e. Wire brushing as the flux is not soluble
in water
c) Washing the parts in boiling water containing 5% HNO3
d) Vacuum blasting
23. A gusset is
a) A bracing between longerons
bracket
c) Used for fail safe construction

b) A type of connecting
d) Like a butt plate

24. Which cross point screwdriver has a taper cross & the sides are not
parallel
a) Phillips screwdriver
b) Reed & prince screwdriver
c) Both are correct
d) None
25. The hallow magnetized shafts of interchangeable screwdrivers hold
hex bits of
a) 1/2 inch size
b) 3/4 inch size
3
c) /8 inch size
d) 1/4 inch size
26. The shape of which screwdriver permits the use of a wrench to
assist in tightening?
a) Stubby screwdriver
b) Phillips screwdriver
c) Heavy duty screwdriver
c) Double ended screwdriver
27. Prick punch has an included angle of
a) 150
b) 450
c)650
0
d) 90
28. While installing a taper pin with a pin punch, the size of the punch
should be
a) Larger than the size of the pin b) Smaller than the size of
pin
c) Same size of the pin
d) Can be of any size
29. Which hammers are used for riveting & stretching of metals

a) Ball peen hammer


c) Soft faced hammer

b) Straight peen hammer


d) Both a and b are correct

30. Soft hammers are made of


1) Babbitt 2) Brass
3) Carbon steel 4) Wood
5) Tool
steel
a) 1,2 & 3 are correct
b) Only 1 is correct
c) 1,2 & 4 are correct
d) 1,2,3 & 4 are correct
31. In N-type semiconductors, the concentration of minority carriers
mainly depends upon
a) Doping technique
b) Number of donor atoms
c) Temperature of material
d) quality of intrinsic material
32. Peak Inverse Voltage (PIV) across the non-conducting diode
(Reverse biased) in center tape full wave rectifier is equal to
a) Vm
b) 2/Vm
c) Vm/2
d)
2Vm
33. Zinor Breakdown in a diode is due to
a) High electric field causes covalent bonds to break
b) Due to the increased velocities of minority carriers
c) Due to heating of junction due to heavy current
d) None of the above
34. Two switches are connected ___________ to obtain AND gate
function
a) In series b) In parallel
c) Either parallel or series
d) None of above
35. Which gate is known as universal gate
a) OR gate
b) NOR gate
d) XOR gate
36. To identify Ferrous metal
a) hardness test is used
c) Heat treatment is carried out

c) AND gate

b) Spark test is used


d) Grinding stone is used

37. Solution heat treatment & artificially eged is indicated by


a) T5
b) T7
c) T6
d)T8
38. The most widely used alloys in aircraft construction are hardened
by
a) Cold work
b) Hot rolling
c) Heat treatment
d) All
the above

39. The heat range for salt bath Furnaces are


a) Depending upon composition of bath
b) As in a) & normally 6500 F to 17000F
c) As in a) & normally 3250F to 24500F
d) None of these
40. In semimonocoque fuselage primary bending load is taken by
a) Frame
b) Stringer
c) Longerons
d)
Bulk head
41. In external bracing wing the landing and aerodynamic loads is
carried by
a) Spar
b) Rib
c) Wing joints
d) Bracing struts
42. The entire cone shaped surface at the cutting end of the drill is
a) Dead centre
b) Point
c) Margin
d) Lip
43. The angle between a lip and axis of the drill bit is known as
______ and mostly 590
a) Heel angle
b) Lip angle
c) Lip clearance
None of these

d)

44. Part of the point drill that actually cuts away the material when a
hole is drilled is known as
a) Point
b) cutting lips
c) Margin
d)
Flutes
45. For flight equilibrium adequate restoring moment can be achieved
by fixing C of G (Centre of Gravity)
a) And C of P (Pressure) together
b) Rear of C of P
c) Front of C of P
d) Along Aerodynamic C of P
46. The point on the chord line at which the total lift of a section at an
aerofoil is considered to act is known as
a) Centre of Gravity
b) Centre of Pressure
c) Lift
d) None of the above
47. The difference between the angles of incidence between the main
plane and tailplane is known as
a) Diheddral
b) Anhedral
c) Longitudinal Dihedral
d) None of above

48. The type of drag which is produced by non lifting surfaces is known
as
a) Parasite drag b) Wing drag
c) Skin friction
d) Induced drag
49. The stability which is due to features incorporated in the design of
the aircraft is called
a) Inherent stability
b) Neutral stability
c) Static stability
d) Dynamic stability
50. The angle of attack of an aerofoil such as wing is the angle
between the
a) Chord of the wing and the longitudinal axis
b) Chord of the wing and the relative airflow
c) Chord of the wing and horizontal axis
d) Angle of incidence and stall angle
51. Crazing appears on the plastic surface in forms of
a) Straight line crack
crack
c) A network of crack running in all direction
visible

b) Zigzag
d) Not

52. If plastic is stored horizontally, the height should not be more than
a) 6
b) 24
c) 12
d) 18
53. In a fail safe spar, the top section consist of
a) Cap and upper web plate riveted together
b) Single
extrusion
c) Splice plates and cap
d) All of these
54. Hydraulic fluid leak is avoided in between the body and the piston
of the break assembly by means of
a) Gasket
b) O-ring packing
c) Seal
d) All
above
55. In cantilever wing design
a) No external support is required
c) Drag wire is fitted

b) Bracing is required
d) None of these

56. The principal structured member of the wing is


a) Rib
b) Spar
c) Stringer
57. In multiple disk break assembly stators are

d) Formers

a) Key to the bearing career


career
c) It rotates

b) Not key to the bearing


d) None above

58. Pressure identification or false brinnelling appears in which type of


corrosion
a) Fatigue corrosion
b) Fretting corrosion
c) Inter granular
corrosion d) Stress corrosion
59. Al and its alloys are covered with pure aluminium to corrosion
resistance is called
a) Sherardizing b) Anodizing
c) Cladding
d)
Chromating
60. Magnesium parts are protected for temporary storage with
a) Cladding
b) Anodizing
c) Plating d) Chrome
pickle treatment
61. The multiple disk break assembly consist of
a) 3 stators
b) 4 rotators
c) 1 bearing career
d) All above
62. In anodizing of Al alloys a thin layer of film on the surface is
formed of
a) Al oxide b) Sodium oxide c) Potassium oxide
d) Calcium
oxide
63. Dichromate treatment is given to
a) Al parts b) Steel parts
Copper parts

c) Magnesium parts

d)

64. Al. Alloy bell cranks employing pressed in taper pins are suspected
to
a) Fatigue corrosion
b) Fretting corrosion
c) Stress
corrosion d) None of these
65. Rigid fuel tanks are tested for leak with the air pressure of
a) 2.5 PSI
b) 1.5 PSI
c) 2 PSI
d) 3 PSI
66. Flexible fuel tanks are tested for fuel leak with the air pressure of
a) 0.25 PSI
b) 1.5 PSI
c) 2.5 PSI
d) 0.5 PSI
67. Fuel leak of the tank is checked for the seepage for the period of
a) 15 min
c) 30 min
c) 45 min
d) 60 min

68. The bladder type of fuel cell is made to size in the cavity when it
sit
a) Larger
b) Smaller
c) Equal
d) All of
these
69. During symmetry checks of Aircraft a spring scale is used with the
steel tape. Generally a pull of force is applied to obtain equal tension
during reading it.
a) 8 lbs
b) 15 lbs
c) 5 lbs
d) 10 lbs
70. To check the rudder hinge alignment the instrument used is
a) Scale
b) Plum bob
c) straight edge d)
Steel tape
71. Taper on a shaft is indicated along the
a) Centre line
b) Base line
72. Set squares can be used for drawing
a) Vertical line
b) Inclined line
d) All of the above

c) Dimension line
c) Parallel line

73. Splined shafts are used to


a) Transmit larger power than keyed shaft
b) Obtain axial
movement
c) Obtain rotary movement
d) All of these
74. Flange couplings are
a) Flexible coupling
c) Compression coupling

b). Rigid coupling


d) Clamp coupling

75. The type of key used in muff coupling is


a) Wood roof key b) Gib-head key c) Round key
Any of these
76. Gear sector gives
a) Continuous motion
c) Reciprocating motion
77. Helical gears are
a) More quiet than spur gear
number of teeth in contact
c) Smooth in operation

d)

b) Intermittent motion
d) None of these
b) Having more
d) All of these

78. Addendum + Duodenum =


a) Working depth b) Whole depth
Backlash

c) Tooth space

79. The basic difference in datum line and phantom line is


a) Thickness of lines
b) Length of lines
c) No. of lines
d) None of these
80. A straight line parallel to a vertical plane has
a) A line of same length in front view and point in top view
b) A line of same length in both views
c) A line of same length in top view and point in front view
d) None of these

d)

PAPER - II
PART IX
1. D

2. C

3. C

4. D

5. A

6. D

7.C

8. C

9. D

10. D

11. A

12. B

13. B

16. D

17. B

18. C

19. C

20.A

21. C

22. C

23. B

24. A

25. D

26. C

27.B

29. A

30. C

31. C

32. D

33. A

34.A

36. B

37. C

38. C

39. C

40. C

43. B

44. B

45 C

41. D

42. B

28.A

14. C

35.B

46. B

47. C

48 A

51.C

52. D

53. A

54. B

55 A

56. B

57. A

58.B

59.C

60. D

61. D

62. A

64. C

65. B

66. A

67. C

68. A

69. C

71. A

72. D

73. A

74. B

75. D

78. B

79. A

80. A

76. B

77. D

63. C

49. B

15. A

50. B

70. B

PAPER - II
PART X
1. Chain
a.
b.
c.
d.

(thick line of 0.7mm) indicates


Visible outlines and edges
Hidden outlines and edges
Surface which have to meet special requirements.
Cutting planes.

2. Raised countersunk heads bolt nominal length is measured from


a. Under the head to the tip
b. Total length of the bolt
c. Threaded length
d. Distance from upper surface of the head (excluding the raised
portion) to the extreme end of shank
3.

4.

Bolt head is of
a Steel
d. Brass

b. Corrosion resistant steel

Bolt head is of
a. Steel
c. C.R.S. close tolerance

c. Al. Alloy

b. Al. Alloy
d. Al. Alloy close tolerance

5. AN 935 is
a. Plain washer
c. Shake proof washer

b. Lock spring washer


d. None of above

6. AN 936 is
a. Shake proof washer
c. Plain washer

b. Lock spring washer


d. None of above

7. Measuring capacity of Vernier Caliper is


a. Full graduated length of main scale
b. Full graduated length of main scale minus the length of the
vernier scale.
c. Full graduated length plus vernier scale
d. All above
8. Vernier caliper is checked for accuracy with the help of
a. Slip gauge
b. Micrometer
c. Straight edge d.
both a) and b)

9. Calliper Micrometer is used for measurement of


a. Small internal diameter
b. Big internal diameter
c. External diameter
d. All above
10. For measurement of cutting a lapping dimension of Drills, Taps and
Reamers instrument used in
a. External micrometer
b. Internal micrometer
c. Vee-block micrometer
d. All above
11. When metal is in contact with plastics, glass wool (non-conducting
material) the corrosion form is known as
a. Fretting
b. Pitting c. Crevice corrosion
d. None of
above
12. Argon cylinders should not be used if the pressure is less than
a. 20 lbf/in
b. 30 lbf/in
c. 10 lbf/in
d. None
13. Grub screws are used for
a. Locking the bolt
c. Locking two threaded components
movement of piston

b. Locking the nut


d.
To
stop

14. Taper pin are manufactured with taper of


a. 1 in 48
b. 1 in 10
c. 1 in 50

end

d. 1 in 60

15. Main constituents of Inconel are


a. Nickel and Iron
b. Nickel and Chromium
d. Nickel and Copper
d. Copper and Manganese
16. Aircraft wheels, brake pedals, control columns are made out of
a. Nickel alloy
b. Magnesium alloys
c. Magnesium alloy castings
d. Wrought Magnesium alloy
17. Anti-corrosive treatment given
reduce electric potential between
aluminium parts is
a. Galvanizing
c. Metal spraying

to copper and its alloys in order to


these parts and its adjacent steel or
b. Parkerizing
d. Cadmium plating

18. In order to increase elasticity and strength and reduce tackiness in


rubber, the process is known as
a. Vulcanizing
b. Calendering
c. Hardening
d. None
19. Aircraft rivets are identified by
a. Head style
b. Alloy
c. Length & diameter
d. All
20. For accurate location of particular area on an aircraft, which of the
following is necessary?
a. Water line
b. Butt line
c. As in a) and b) in conjunction with station line
d. None
21. Which type of corrosion is occurred in stainless steel after electric
arc welding?
a. Pitting
b. Galvanic
c. Inter crystalline
d. Fretting
22. For spot welding, in stainless steel, which is most suitable
a. Low-voltage
b. High-amperage
c. Low-voltage and High-amperage
d. High-voltage and Low-amperage

23. Heat generated in spot welding is measured by


a. Resistance x (Current)2 x Time
b. Resistance x Time / (Current)2
c. (Current)2 / Resistance x Time
d. Resistance x Current
24. Which of the following is Non-Magnetic?
a. Inconel
b. K-Monel
c. Monel
d. All

25. SAE
a.
b.
c.
d.

13XX represents
Magnesium Steel
Manganese Steel
Silicon Steel
Chromium Steel

26. Hot piece of metal is increased in thickness and decreased in


length
a. Upsetting
b. Down setting
c. Swaging
d. Rolling
27. Rivets are designed
a. Stronger in shear
b. Stronger in tension
c. Should not be subjected to excessive tension load
d. Both a) and c)
28. Zero fuel weight means
a. AUW minus weight of fuel
b. Weight of cargo, passenger and crew
c. Maximum allowable weight of loaded aircraft without fuel and
statement b)
d. All of these
29. I-beam is produced by
a. Rolling
b. Casting
c. Forging
d. None
30. Caustic cleaning products used on Al-structure have the effect of
producing
a. Passive oxidation
b. Improved corrosion resistance
c. Corrosion
d. None
31. Fayed surface cause concern in chemical cleaning because of the
danger of
a. Forming passive oxide
b. Entrapping corrosive material
c. Corrosion by embedded iron oxide
d. All of the above
32. The rust or corrosion that occurs with most of the metal is the
result of

a. A tendency for them to return their natural state


b. Blocking the flow of electrons in homogenous metals or
between dissimilar metal
c. Electron flow in or between metal for cathode to anode area
d. All of the above
33. Which of the listed condition is not one of the requirements for
corrosion to occur
a. Presence of electrolyte
b. Electrical contact between an anodic area and a cathodic area
c. Presence of passive oxide film
d. None of these
34. Inter-granular corrosion on Al-alloy part
a. May be detected by surface pitting, white powdery deposit
b. Appears as thread like filament
c. Cannot always be detected by surface indication
d. All of the above
35. Which type of pipe wrench is designed with adjustable serrated
jaws for gripping round pipes?
a. Warnok type
b. Stillson type
c. Super wrench tool
d. Williams type
36. Vise
a.
b.
c.
d.

grip pliers is also known as


Heavy pliers
Lever jaw wrench
Monkey pliers
None

37. Punch holders are used to hold


a. Punches
b. Chisels
c. Both a & b are correct
d. As in a, when a hard blow is required
38. Which pliers can be used for completing the safety wire operation?
a. Safety wire pliers
b. Diagonals & duck bill pliers
c. Both a & b are correct
d. As in a & diagonals

39. Diagonals are used for


a. Cutting steel wires & rods
b. Cutting bolt heads
c. Both a & b are correct
d. None
40. The shape of long nose pliers is
a. Round
b. Half-round
c. Square
d. None
41. The jaws of vise grip pliers is released from locking by
a. A small lever at each handle
b. A compound lever at both handles
c. A small lever at one of the handles
d. None
42. Which thread is used where a great strength is required in one
direction?
a. Acme
b. Square
c. Worm
d. Buttress
43. In interlocking-joint pliers,
a. There are a number of holes at the hinge point
b. There are two holes at the hinge point
c. There are several curved grooves at the hinge point
d. None
44. Which nut is used to prevent other nuts from turning on threaded
bolt or rod
a. Self-locking nut
b. Jamb nut
c. Stainless steel nut with cotter pin
d. None of these
45. The content of CO2 fire extinguisher or N2 pressurized extinguisher
is checked by
a. Weight and pressure gauge
b. Marking on neck
c. By operating the extinguisher
d. All of the above

46. Choose incorrect statement


a. Yellow poly propylene provide insufficient strength
b. Proper tension in rope allows 1 movement
c. Manila rope requires extra slak due to shrinks
d. The rope from tail should pull away at about 450 to each side
of tail
47. Which type of jack is used for L/G retraction check
a. Single base jack
b. Bottle neck jack
c. Screw jack
d. Tripod jack
48. Which measuring tool is used for outside or inside measurement
for faster work
a. Vernier micrometer
b. Vernier calliper
c. Micrometer calliper
d. None of these
49. Which is incorrect statement
a. If corrosion is present in control cable should be replaced
b. Cable used in seaplane must be coated with paral-ketone
c. For detection of corrosion, cable twist in same way of lay
d. Carbon steel cable must be used with protective coating
50. After welding aluminium parts flux should be removed by
a. Immersing them in Luke warm water for 30 minutes
b. Mechanical means, i.e. Wire brushing as the flux is not soluble
in water
c. Washing the parts in boiling water containing 5% HNO3
d. Vacuum blasting
51. A gusset is
a. A bracing between longerons
b. A type of connecting bracket
c. Used for fail safe construction
d. Like a butt plate
52. In computer terminology, MICR means
a. Magnetic Ink Character Recognition
b. Magnetic Ink Computer Recognition
c. Monitor Indicating Computer Relay
d. Mass Information Computer Record

53. The phase difference between voltage and current in a purely


resistive circuit is given by
a. 00
b. 900
c. 450
d. 1350
54. One
a.
b.
c.
d.

micro farad is equal to


0.001 milli farad
100 milli farad
1000 milli farad
10 milli farad

55. To smoothen the DC in rectifier, we employ


a. LPF
b. HPF
b. BPF
d. None
56. The Voltage / Current across the short circuit
a. V = max
I=0
b. V = 0
I = max
c. V = 0
I=0
d. V = max
I = max
57. The vacuum tube has
a. Directly heated anode
b. Indirectly heated cathode
c. Directly heated cathode
d. Indirectly heated anode
58. The name Superhet is used for
a. AM receiver
b. FM receiver
c. AM transmitter
d. FM transmitter
59. Two resistances of 15, 12 ohms each are connected in parallel
across a supply, giving 27 ampere, then current through 15 ohm will
be
a. 27 amp
b. 12 amp
c. 15 amp
d. 1 amp
60. Most effective method of removing rust from ferrous metal is
a. Steel wire brush
b. Sand paper
c. By abrasive blasting

d. Washing with hot shop solution


61. A) Rivet smaller than 3/32 diameter are never used on stressed
structure
B) Never replace 2024T rivet with 2117T rivet
a. Both are correct
b. Both are incorrect
c. Only A) is correct
d. Only B) is correct
62. Regarding permanent ballast
a. Lead bar or plate is used
b. Painted red and placarded
c. Bolted as near as possible to CG
d. Both A and B
63. Transverse pitch is
a. Twice the rivet diameter
b. 70% of rivet pitch
c. 75% of rivet pitch
d. 6-8 diameter
64. Rivet pitch is
a. Distance between center of rivet in a row
b. Distance between edge to center of rivet
c. Four times the rivet diameter
d. Both a) and c) are correct
65. Edge distance (minimum) is
a. 4D
b. 2D
c. 6-8D
d. Any of the above
66. The amount of rivet length used for shop head is
a. 11/2 x diameter of rivet
b. 4 x diameter of rivet
c. 3 x diameter of rivet
d. All of the above
67. Which plating process provide excellent base for paint
a. Cd Plating
b. Zn Plating
c. Granodizing
d. All of the above

68. Which treatment give excellent base for paint


a. CR Plating
b. Parkerizing
c. Metal spraying
d. Zn plating
69. The process use zinc as a medium for plating
a. Parkerizing
b. Sheradizing
c. Galvonizing
d. Both b) and c)
70. In Electrically driven attitude indicators, the gyro rotates approx.,
at
a. 20000 rpm
b. 21000 rpm
c. 21500 rpm
d. None of the above
71. During functional test of direction indicator, the drift should be
checked which should not exceed
a. 2 degree in 15 minutes
b. 3 degree in 15 minutes
c. 2 degree in 30 minutes
d. 3 degree in 30 minutes
72. Performance test of instruments should be carried out
a. Before installation
b. At times when indication and operation are suspected
c. At periods mentioned in aircraft maintenance manual
d. All of the above
73. Worm threads have a thread angle of
a. 45 degrees and is similar to ACME threads
b. 29 degrees and is similar to ACME threads
c. 29 degrees and depth of threads are deeper than ACME
threads
d. 29 degrees and ACME threads are deeper than worm threads
74. The figure shown here is of
a. A simple gear train and the gear D moves at half speed of
gear A
b. As in a & the gear D moves in the same direction of the
gear A

c. A compound gear train & the gear D moves in the opposite


direction of the gear A
d. A simple gear train and the gear D moves in the opposite
direction at a double speed of gear A
100T

30

30

50T

75. Which of the following memories has got equal access time for all
locations of the memory limit?
a. Read Only Memory (ROM)
b. Programmable Read Only Memory (PROM)
c. Random Access Memory (RAM)
d. Erasable ROM
76. To get a basic D.C. generator from A.C. generator which of the
following arrangement is made?
a. By replacing the slip rings of the A.C. generator with
commutator
b. By the addition of extra slip rings
c. By connecting a rectifier
d. None of the above
77. The rotating part of a DC generator is called
a. Field coil
b. Yoke
c. Armature
these

d. None of

78. Variations of D.C. voltage generated by D.C. generator is called


a. Ripple
b. R.M.S. c. Average
d. Crest
79. The brushes in generator are generally made up of
a. High grade carbon
b. High grade silicon
c. High grade selenium
d. High grade zinc
80. The term 10-5 farads mean
a. 1 mili-farad
b. 10 micro-farad
c. 10 nano-farad d. None

PAPER - II
PART X
1.C
6.A
11.C
16,.C
21.C
26. A
31. B
36. B
41. C
46. A
51.B
56.B
61.C
66.A
71.B
76.A

2.D
7.B
12.A
17. D
22. C
27. D
32. A
37. C
42.D
47. D
52.A
57.B
62.C
67.C
72.D
77.A

3.B
8.D
13.C
18. A
23. A
28. C
33.C
38. C
43.C
48.B
53.A
58.A
63.C
68.B
73.C
78.A

4.C
9.A
14.A
19. D
24.B
29. A
34.C
39. D
44.B
49.C
54.A
59.B
64.D
69.D
74.D
79.A

5.B
10.C
15.B
20. C
25. B
30. C
35.B
40. B
45.A
50.C
55.A
60.C
65.B
70.B
75.C
80.B

PAPER - II
PART XI
1. Diamond is a:
(a) Metal
Composite

(b) Non-metal

(c) Glass

(d)

2. Number of atoms in a Body Centered Cubic (BCC) crystal are:


(a) Ten
(b) Seventeen
(c) Nine
(d) Fourteen
3. Type of bond formed in a material by sharing of electrons in
different atoms is:
(a) Ionic Bond
(b) Covalent Bond
(c) Metallic Bond
(d) Electrostatic bond
4. A crack in a metal due to corrosive atmosphere and static tensile
stress is known as:
(a) Bauschingers effect (b) Work hardening (c) Season
cracking (d) Strain aging
5. A metal part or structure fails under repetitive or fluctuating loading
or stress is called:
(a) Fatigue fracture
(b) Ductile fracture
(c) Creep
fracture
(d) Brittle fracture
6. (1) An intermetallic compound is a form of alloy, where as
(2) Substitutional solid solution is a type of solid solution
(a) 1 is correct & 2 is incorrect
(b) 2 is correct &
one is incorrect
(c) Both (1) and (2) are incorrect
(d) Both, (1) and (2)
are correct
7. Property of a material to resist indentation is known as:
(a) Toughness
(b) Hardness
(c) Brittleness
(d) Strength
8. Conductivity and Expansion are physical terms which are related to:
(a) Electricity
(b) Heat
(c) Cooling
(d)
None of these

9. Addition of carbon to the surface of steel to make it hard, is known


as:
(a) Case hardening
(b) Carburizing (c) Quenching
(d) None of these
10. Permanent deformation of metal caused by applied load is called:
(a) Stress
(b) Elastic deformation
(c) Plastic
deformation
(d) None of these
11. The point at which marked increase in deformation occurs without
increasing the load during tensile testing of a material, is:
(a) Yield point
(b) Yield strength (c) Proof strength(d)
Tensile strength
12. For tensile testing, the extensometer must be calibrated to:
(a) 0.0001 inch (b) 0.0002 inch (c) 0.0003 inch (d) 0.0004
inch
13. Yield strength of a metal can be determined by:
(a) Divider method
(b) Drop of beam
method
(c) Set method
(d) None of these
14. In Brinell Hardness Testing, hard metal will have:
(a) Large Brinell number
(b) Small Brinell
number
(c) No effect by hardness
(d) None of these
15. In Vickers Hardness Test, angles between two opposite diagonals
of diamond pyramid is:
(a) 1260
(b) 1360
(c) 1460
(d) 1560
16. Size of specimen taken for reverse bending test is:
(a) 5 inches
(b) 10 inches
(c) 15 inches
(d) 20 inches
17. In reverse bending test, number of bends require for small wires
(a) 50 bends
(b) 7 bends
(c) 10 bends
(d) 90 bends
18. Torsion test is carried out on
(a) Aircraft tubes (b) Wires
Bars & rods

(c) Sheets & strips

(d)

19. In radiography inspection, the wave length of x-rays are in order of


(a) 10-6
(b) 10-10
(c) 10-11
(d)
-6
-9
10 10
20. Circular magnetization detects the defect approximately:
(a) In line with flux
(b) Parallel to the line
of flux
(c) Parallel to the axis of the part
(d) None of these
21. Type of bond formed in a material by Electrons cloud is:
(a) Ionic bond
(b) Covalent bond
(c) Mettalic bond
(d) Electrostatic
22. For tensile testing, it is permitted to taper the gauge length of the
specimen towards center, maximum by:
(a) 0.001 inch
(b) 0.002 inch
(c) 0.002 inch
(d) 0.004 inch
23. For elastic limit determination, the extensometer reading is taken
from:
(a) 5% load of expected elastic limit
(b) 10% load of
expected elastic limit
(c) 15% load of expected elastic limit
(d) 20% load of
expected elastic limit
24. While testing a material for hardness, sufficient distance from
edges should be there to avoid:
(a) Buldging at opposite side
(b) Deflection while
testing
(c) Ridge scales
(d) Scratches
25. (1) Diameter of ball used for Brinell Hardness Test is up to
inches, where as
(2) Load applied for soft material is 500 kg.
(a) (1) is true and (2) is false
(b) (2) is true and (1)
is false
(c) Both are true
(d) Both are false
26. Brinell Hardness Number is obtained by:
a) Size of ball divided by area of depression
b) Area of depression divided by size of ball
c) Load applied divided by area of depression
d) None of these

27. Maximum size of ball for Rockwell hardness test is:


(a) 5mm
(b) 10mm
(c) mm
mm

(d) 1

28. In Rockwell hardness test, the working range of the B scale is:
(a) B0 B150
(b) B0 B100
(c) B0 B20
(d) None of these
29. In Rockwell hardness test, B scale is a combination of:
(a) Diamond cone, 150kg load and Red dial
(b) 1/16 inch ball, 100kg load and Black dial
(c)Diamond cone, 100kg load and Black dial
(d) 1/16 inch ball, 100kg load and Red dial
30. Minimum thickness necessary with hard steel for Rcokwell
hardness test is:
(a) 0.027 inch
(b) 0.27 inch
(c) 0.0027 inch
(d) None of these
31. Load applied in Shore Scleroscope hardness test is:
(a) 30 kg
(b) 50 kg
(c) 10 kg
these

(d) None of

32. For bending test of sheet and strips, the size of test specimen is:
(a) 1 to 1 inch wide with suitable length
(b) 1 by in cross section
(c)Full section
(d) None of these
33. In reverse bending test, the specimen is bent through an angle of:
(a) 600
(b) 900
(c) 1200
0
(d) 180
34. In Izod impact test, the specimen is :
(a) Supported on two supports
jaws
(c) Attached with pendulum

(b) Clamped in heavy


(d) None of these

35. In Hydrostatic test, welded exhaust tubing are subjected to an


internal pressure sufficient to put the welded seam under a tensile
stress of:
(a) 1000 PSI
(b) 10000 PSI
(c) 100000 PSI
(d) 1000000 PSI

36. In torsion testing of wires, speed of revolution should not be more


than:
(a) 80 revolution/min (b) 70 revolution/min (c) 60
revolution/min
(d) 50 revolution/min
37. In fatigue testing, the value of stress below which failure of
material will not occur is known as:
(a) Plastic limit (b) Elastic limit (c) Proof stress (d)
Endurance limit
38. Gamma rays used for inspecting aircraft material for internal
cracks / defects are having wave length of:
(a) 10-3
(b) 10-6
(c) 10-9
-11
(d) 10
39. (1) Sulfur is a harmful impurity in plain carbon steel
(2) Phosphorus is very much useful element of plain carbon steel
(a) Both are true
(b) Both are false
(c) (1) is true (2) is false
(d) (1) is false and (2) is true
40. High carbon steel is used for:
(a) Great hardness and low ductility
and strength
(c) Great hardness and machinability

(b) Great ductility


(c) All of these

41. Which of the following is more useful for taking backups?


(a) Floppy disk (b) Hard Disk
(c) Optical Disk
Cartridge

(d)

42. One Megabyte is _____________ bytes.


(a) 1048576
(b) 1000
10

(d)

(c) 102756

43. The material used as heat sink in semiconductors is


(a) Silicon
(b) Germanium (c) Carbon
Selenium

(d)

44. When the conduction-band orbit of one atom may intersect the
hole orbit of another atom merging of a free electron and a hole
takes place. This merging of electron and hole is known as
(a) Current flow
(b) Minority current flow
(c) Combination
(d) Recombination

45. The barrier potential at 25C in respect of silicon and germanium


is
(a) Si-0.7V and Ge-0.3V
(b) Si-0.3V and Ge0.7V
(c) Si-0.7V and Ge-0.7V
(d) Si-0.3V and Ge0.3V
46. Once the breakdown voltage is reached, the diode can conduct
(a) Heavily (b) Very flow
(c) Moderately
(d)
None of these
47. An electronic device which converts alternating current into d.c. is
called
(a) Detector
(b) Rectifier
(c) Oscillator
(d)
None of these
48. Mark the incorrect statement about a bimetallic strip
(a) It consists of two metals joined together at their interface
to form a single strip.
(b) One of the metal is invar, a form of steel with a 26% nickel
content and a negligible coefficient of linear expansion.
(c)The other metal may be brass or steel both of which have
high linear expansion coefficient.
(d) None of these.
49. Many of the instruments depend for their operation on sensitive
electrical circuits which are protected against adverse effects of
atmospheric temperature, pressure and humidity by
(a) filling the cases with nitrogen
(b) filling the cases
with helium
(c) filling the cases with argon
(d) either (a) or (b)
50. Instruments displaying information which is to be read accurately
and at frequent intervals have scale about _____________ in length
fitting into standard ____________ in cases.
(a) 6 in & 3 (b) 7 in & 3
(c) 7 in & 3
(d)
none of these
51. The rolled section having dimension of 6x 6 or larger &
approximately square is called
(a) bloom
(b) billet
(c) slab
none of these

(d)

52. To identify ferrous metal


(a) hardness test is used
(c) heat treatment is carried out
used

(b) spark test is used


(d) grinding stone is

53. Solution heat treated & artificially edged is indicated by


(a) T5
(b) T7
(c) T6
(d) T8
54. The most widely used alloys in aircraft construction are hardened
by
(a) cold work
(b) hot rolling
(c) heat
treatment (d) all the above
55. The heat range for salt bath furnances are
(a) depending upon composition of bath.
(b) as in (a) & normally 650F to 1700F.
(c)as in (a) & normally 325F to 2450F.
(d) none of these.
56. In semimonocoque fuselage primary bending load is taken by
(a) frame
(b) stringer
(c) longerons
(d)
bulk hand
57. In external bracing wing the landing and aerodynamic loads is
carried by
(a) spar
(b) rib
(c) wing joints
(d) bracing struts
58. In main plane at the inboard end of the wing near the attachment
point to the fuselage heavily stressed rib is called
(a) butt rib
(b) bulk head rip (c) compression rib
(d)
all of them
59. Aircraft requiring extra wing area to aid lift often are
(a) split flap
(b) plain flap
(c) fowler flap
(d) all of them
60. On multiengine aircraft Nacelles or pods are located
(a) above the m/p
(b) below the m/p
(c) at the leading edge of the m/p
(d) all the above
61. An amplifying, comparative gage is an instrument that amplifies
the variation in the size of two similar parts by

(a) 2 times
20 times

(b) 5 times

(c) 10 times

(d)

62. Johansson precision gage blocks, the second series of gage blocks
contains
(a) 19 blocks
(b) 49 blocks
(c) 81 blocks
(d) none of these
63. The entire cone shaped surface at the cutting end of the drill is
(a) dead centre
(b) point
(c) margin
(d)
lip
64. The angle between a lip and axis of a drill bit is known as
___________ and mostly 59.
(a) heel angle
(b) lip angle
(c) lip clearance
(d) none of these
65. Part of the point drill that actually cuts away the material when a
hole is drilled is known as
(a) point
(b) cutting lips
(c) margin
(d)
flutes
66. A capacitor consists of two
(a) conductors separated by an insulator called the di-electric.
(b) insulators separated by a conductor.
(c)insulators separated by air medium.
(d) conductors separated by air medium.
67. In a capacitor electric charge is stored in
(a) metal plates (b) di-electric
(d) none of these
68. Unit of m.m.f. is
(a) weber

(b) gilbert

69. Joule/coloumb is the unit of


(a) electric field potential
(d) none of these

(c) both (a) & (b)

(c) maxwell
(b) potential

(d) henry
(c) charge

70. In a lead-acid battery, excessive formation of lead sulphate occurs


due to
(a) idleness of battery for a long time
(b) low level of
electrolyte
(c) persistent under charging
(d) all of them

71. Common impurity in a battery electrolyte is


(a) dust particle (b) iron
(c) lead crystals (d) sodium
chloride
72. Overcharging of lead-acid battery will cause
(a) excessive gassing
(b) loss of active
material
(c) increase in temperature resulting in buckling
(d) all of
them
73. Total horse power developed by piston engine is
(a) IHP
(b) BHP
(c) FHP
Actual horse power
74. Factor affecting volumetric efficiency is
(a) improper fuel injection
(c) low engine power
timing

(d)

(b) cylinder bore


(d) improper valve

75. In the formula indicated


HP= PLANK , where N stands for
33000
(a) number of power stroke per minute
cylinder per engine
(c) number of RDM per power stroke
these
76. White arc on ASI dial indicates airspeed range
(a) normal operating range
minimum limits
(c) aircraft landing flaps may be extended
these

(b) number of
(d) none of

(b) maximum &


(d) none of

77. Mark the correct statement about


A field effect LCD
(a) It incorporates additional plates called polarizers on the
front & back glass plates of the assembly.
(b) It contains a specially prepared inside glass surface which
causes liquid crystal.
(c) The molecular configuration causes the plane of polarization
to be reflected by 90 as it passes through LCD.
(d) All the above.

78. A quality of precision gage have the accuracy of


(a) 0.000008 inch
(b) 0.000004 inch
(c) 0.000002
inch (d) 0.000004 inch
79. The convenient gages which are designed to inspect the thickness
of paper, plastic, steel metal, leather and so on with great accuracy
are
(a) indicating depth gage
(b) indicating thickness
gage
(c) amplifying comparative gage
(d) indicating gage
80. For flight equilibrium adequate restoring moment can be achieved
by fixing C of G (Centre of Gravity)
(a) end C of P (Pressure) together
(b) rear of C of P
( c) front of C of P
(d) along aerodynamic
C of P

PAPER - II
PART XI
ANSWERS:
1. B

2. C

3. B

4. C

5. A

6. D

7. B

8. B

9.A

10. C

11. A

12. B

13. C

14. A

15. B

16. B

17. A

18. B

19. D

20. C

21. C

22. C

23. D

24. B

25. B

26. C

27. C

28. B

29. D

30.A

31. D

32. D

33. D

34. B

35. B

36. C

37. D

38. D

39. C

40. A

41. A

42. A

43. C

44. D

45. A

46. A

47. B

48. B

49. D

50. C

51. A

52. B

53. C

54. C

55. C

56. C

57. D

58. D

59. C

60. D

61. C

62. B

63. B

64. B

65. B

66. A

67. B

68. B

69. A

70. D

71. A

72. D

73. A

74. D

75. A

76. C

77. D

78. B

79. B

80. C

PAPER - II
PART XII
1. Maximum permissible silicon in steel is:
(a) 0.3%
(b) 0.4%
0.6%

(c) 0.5%

(d)

2. An element of steel which is white in colour and increases the


strength, yield point and hardness without effecting the ductility:
(a) Chromium
(b) Molybdenum
(c) Silicon
(d) Nickel
3. An alloying element of steel which improves its homogeneity and
reduces the grain size, is:
(a) Nickel
(b) Molybdenum (c) Chromium
(d)
Silicon
4. The High Speed Steel used for tools, which will retain its cutting
edge even when heated to dull redness by working:
(a) Nickel-chromium
(b) Tungsten-chromium steel
(c) Vanadium-Tungsten steel
(d) Chromium-molybdenum
steel
5. In SAE steel numbering system, the second digit indicates:
(a) Average carbon content
(b) Type of steel
(c) Number of alloying elements
(d) Approximate percentage
of predominant alloy
6. The numerals and digits for 3.50% Nickel steel in SAE steel
numbering system is:
(a) 25xx
(b) 2xxx
(c) 23xx
(d) 24xx
7. In AN-QQ-S-689 specification, AN indicates:
(a) Army-Navy (Aeronautical) standard
(b) Air force-Navy (Aeronautical) specification
(c)American National (Aeronautical) specification
(d) None of these
8. SAE 1435 steel is used for structural tubings, its Military
specification is:
(a) MIL-T-6737
(b) MIL-T-6731 (c) MIL-T-6732
MIL-T-6735

(d)

9. While heating the steel, the critical points are designated by:
(a) Ac1, Ac2,
(b) Ar1, Ar2,
(c) Ar3-2
(d)
Arcm
10. At what percentage of carbon content, two upper critical points
merge together and forms a single critical point known as Ar3-2
(a) Slightly above 0.1%
(b) Slightly above 0.2%
(C) Slightly above 0.4%
(c) at 0.85%
11. Carbon is in chemical combination with iron as iron carbide, which
is known as:
(a) Austenite
(b) Pearlite
(c) Martensite
(d)
Cementite
12. Steel above 0.85% carbon content is known as:
(a) Hyper-eutectoid
(b) Hypo-eutectoid
Eutectoid
(d) None of these

(c)

13. Steel above 0.85% carbon content is composed of:


(a) Austenite
(b) Cementite and
martensite
(c) Martensite and troostite
(d) Pearlite with excess
cementite
14. Main constituent of hardened steel is:
(a) Austenite
(b) Troostite
Martensite

(c) Sorbite

(d)

15. Fine grain of the steel is obtained when it is heated:


(a) Below critical range
(b) Well above critical
range
(c) Slightly above critical range
(d) Up to upper critical
point
16. The hardest structure obtained in the steel is:
(a) Pearlite
(b) Troostite
(c) Martensite
(d) Sorbite
17. Soaking time for steel is:
(a) 4 hours per inch thickness
thickness
(c) 2 hours per inch thickness
thickness

(b) 3 hours per inch


(d) 1 hour per inch

18. Spheroidizing is a type of annealing which improves machinability


of :
(a) Low carbon steel
(b) Medium carbon
steel
(c) High carbon steel
(d) Alloy steel
19. Normalizing is carried out to:
(a) Induce ductility
strength
(c) Improve machinability

(b) Improve hardness and


(d) All of these

20. The most severe quenching medium is:


(a) Brine
(b) Water
(d) Air

(c) Oil

21. Dry heat furnace are fired by:


(a) Oil
(b) Gas
(d) Any one of these

(c) Electricity

22. To prevent scaling, better temperature regulation and for uniform


heating, the type of furnace to be used is:
(a) Liquid furnace
(b) Dry heat furnace
(c) Open hearth furnace
(d) Electric furnace
23. Sufficient period of soaking of aircraft steel parts is:
(a) 30 60 minutes
(b) 15 45 minutes
(c) 30 45 minutes

(d) 1 hour 2 hour

24. For water quenching, temperature of water must be maintained:


(a) Below 600F
(b) Below 650F
(c) Below 700F
(d) Below 800F

25. For normalizing SAE 1025 mild carbon steel, the temperature
should be:
(a) 1600 16250F (b) 1625 16750F
(c) 1650 17000F
0
(d) 1675 1725 F
26. Special steel HY-TUF has a good toughness at a tensile strength
of:
(a) 2,30,000 psi
(b) 2,40,000 psi
(c) 2,50,000
psi
d) 2,60,000 psi

27. The steel to be used for case hardening purpose is:


(a) Low carbon steel
(b) Medium carbon
steel
(c) High carbon steel
(d) Alloy steel
28. For solid carburizing, the metal box is having 2 inches legs
(a) To avoid touching of box with furnace
(b) For free circulation of furnace gases
(c) For proper support of the box
(d) All of these
29. Liquid carburizing is used for small parts, where case depth
required upto:
(a) 0.010 inch
(b) 0.020 inch
(c) 0.030 inch
(d) 0.040 inch
30. In gas carburizing, the parts are heated in:
(a) Carbon atmosphere furnace
(b) Amonia gas
(c) Carbon-dioxide gas
(d) Any one of these
31. The sequence of case hardening consists of:
(a) Carburizing, tempering, case hardening and core refining
(b)
Carburizing, core refining, case hardening and tempering
(c)
Carburizing, tempering, case hardening and core refining
(d) Carburizing, case hardening, core refining and tempering
32. For case hardening MIL-S-6709 describe two types of nitralloys, in
which composition-A is:
(a) Free machining steel
(b) High carbon steel
(c) Nitriding stainless steel
(d) High core strength
steel
33. Which of the following is a mechanical treatment in shaping of
metal:
(a) Casting
(b) Sand blasting (c) Rolling
(d)
Centrifugal cast
34. While shaping of a metal if the sectional dimension is less than 6X6
inch and approximately square, the shape is called:
(a) Billet
(b) Bloom
(c) Slab
(d)
Mold

35. Complicated sections or sections required in small quantity are


usually:
(a) Hot rolled
(b) Cold rolled
(c) Drawn
(d) Forged
36. In drop forging, the inside faces of the die are given a slope of 3 0
70 to permit drawing out the finished parts. This slope is referred to
as:
(a) Up setting
(b) Drawing angle
(c) Draft
(d) Fin

37. When finely powdered metal is placed in a die and pressed through
a plunger, it forms a compact mass by:
(a) Attraction forces of the particles
(b) Forming a bond
(c) By welding the particles together
(d) By interlocking of particles
38. Cold working of metal increases its:
(a) Toughness and ductility
(b) Strength and ductility
(b) Hardness and ductility
(d) Strength and hardness
39. Size of hot drawn rod used for cold drawing of wires are:
(a) 1/8 3/4 inch diameter
(b) 1/16 1/32 inch diameter
(c) 1/32 5/8 inch diameter
(d) None of these
40. Blow hole is a defect in steel, which can occurs in
(a) Ingots
(b) Rolling
(c) Drawing

(d) Forging

41. All submerged parts & hull of seaplane is sprayed with liquid
lanoline upto height of _____________ above water line
(a) 1 Feet
(b) 2 Feet
(c) 1 meter
(d) 2 meter
42.

Mark the correct statements


(a)
Steel wool is used on Al-alloy for corrosion removal
(b)
Clad-Al can be cleaned by mechanical method
(c)Trichloroethylene is used for removal of grease
(d)
All of the above

43. Evidence of surface corrosion and extent of pitting should be


tested by
(a) Hardness testing
(b) Impact testing
(c) Probing with a fine needle
(d) None of these
44. Exhaust of Aero-engine made of stainless formed
________________ due to high temperature
(a) Crevice corrosion
(b) Electrolytic
corrosion
(c) Inter-granular corrosion
(d) Stress corrosion
45. Which type of corrosion is occurred in mounting bolts of engine
and wings ?
(a) Inter-granular corrosion
(b) Stress corrosion
(c) Concentrating cell corrosion
(d) Fettling
corrosion
46. Heated section checked with magnet for corrosion detection,
basically that indicate their relative
(a) Conductivity of part
(b) Permeability
of part
(c) both (a) and (b)
(d) None of these
47.

Which is most suitable condition for storage of Aircraft part?


(a) Less than 60% humidity
(b) Equal to 60%
humidity
(c) More than 60% humidity
(d) None of these
48.

Paint stripper is removed with


(a) Steel wool
(c) Aluminium wool
material

(b) Emery cloth


(d) Non-metallic

49.

Which type of stripper is used on plastic or windows parts?


(a) Water-miscible paint remover
(b) Solvent-miscible
paint remover
(c) Both (a) & (b)
(d) None of these
50.

Anodic film can be removed by a solution of


(a)
10% Sulphuric acid + 4% Potassium fluoride
(b)
20% Sulphuric acid + 10% Potassium fluoride
(c)20% Sulphuric acid + 20% Potassium fluoride
(d)
All of the above

51.

Chromate film treatment is carried on __________ material


(a) Al-alloy
(b) Mg-alloy
(c) Steel-Alloy
(d) Titanium

52.

Cadmium plating can be removed by


(a) Mechanical cleaning
(c) Both (a) & (b)

53.

(b) Chemical cleaning


(d) None of these

Mark the correct statement regarding chemical cleaning of steel


(a)
Corrosion on steel can be removed by pickling solution
(b)
Phosphoric acid can also be used
(c)As in (b), it dissolved oxide film and partly inhibit the steel
surface
(d)
All of the above

54. Mark the correct statement regarding chemical cleaning of Alalloys


(a)
Light corrosion can be removed by solvent
(b)
Heavy deposits on clad Al-alloy can be removed chemically
(c)Heavy deposits on non-clad Al-alloy can be removed
mechanically
(d)
All of the above
55. Which of the following corrosion remover required a followed-up
action of chromate bearing conversion coating treatment?
(a) Chromic-acid corrosion remover
(b) Phosphoric-acid corrosion remover
(c) Butyl alcohol + Isopropyl alcohol + water
(d) Nitric acid + water
56.

Which acid is used for cleaning of Mg-alloy?


(a) Chromic acid
(b) Phosphoric acid
(c) Nitric acid
(d) Sulphuric acid

57.

Steel and Non-clad Al-alloy can be cleaned by


(a) Wet glass paper
(b) Dry emery paper
(c) Dry sand paper
(d) As in (a) & water acts as
lubricants
58. Which type of scraper is used for corrosion removal on casting or
forging parts?
(a) Steel carbide tipped
(b) Plastic
copped tip scraper
(c) Abrasive tipped cap scraper
(d) None of these

59.

Mark the correct statement regarding battery component


(a)
Lead-acid battery compartment neutralized by bicarbonate of soda
(b)
Ni-Cd battery compartment neutralized by acetic acid
(c)The sump vent jar containing moist absorbent pad with
neutralizing agent
(d)
All of these

60. Human wastes corrode the lavatory area, because it is ________


in nature
(a) Acidic
(b) Caustic
(c) Neutralizing agent
(d) None of these
61.

Grip length of the bolt is


(a) Total length of the bolt
(b) Plain sank portion of the bolt
(c) Length under the head of the bolt to the end of the bolt
(d) None of these

62.

In close tolerance bolt, force applied to drive in is


(a) 10 ounce hammer
(b) 20 ounce hammer
(c) 12 to 14 ounce hammer
(d) Sledge hammer

63.

AN 4-7 bolt shows


(a) 7/8 dia
4length
(d) dia
64.

Bolt of class 4 fit is


(a) Loose fit
(c) Close fit

(b) length

(c)

(b) Free fit


(d) Tight fit

65.

Special washer AC 950 and AC 955 are used where


(a) Bolt is installed at angle to surface
(b) Bolt is
installed head down
(c) It can be used any where
(d) None of
these
66. To prevent the crushing surface on wooden structure with nut
and bolt, the washer used is
(a) AN 936
(b) AN 935
(c) AN 970
(d) AN 960
67.

Where shear load is taken by the bolt, the nut used is


(a) Plain nut
(b) Castle nut

(c) Castellated shear nut

(d) Self locking

nut
68. In the patch repair of the Aircraft skin, the edge distance
(distance from the centre of the rivet to the edge of the sheet)
should be (d is diameter of rivet)
(a) 2d to 4d
(b) 8d
(c) 6d
(d)
75% of the pitch
69.

Pitch of the rivet should be


(a) 1 d
(c) 1 x d

(b) 6d to 8d
(d) All of these

70. The amount of the length required to form the head of the rivet
is
(a) 2 d
(b) 4 d
(c) 1 x d
(d) 8 d
71.

Chamfering of the patch plate is done at the angle of


(a) 25
(b) 45
(c) 60

(d)

15
72.

In patch repair, clearance between the rivet and hole should be


(a) 0.008
(b) 0.5
(c) 0.002 to 0.004
(d) 0.4
73.

A rivet with part no. AN 470 AD 3-5 is having a diameter of


(a) 3/32
(b) 5/32
(c) 3/16
(d)

5/16
74.

Seam welding is
(a) Pressure welding
welding
(c) Electric resistance

(b) Non-pressure
(d) Both (a) & (c)

75.

In which type of welding, the electrode is non-consumable


(a) TIG
(b) MIG
(c) Electric resistance
(d) Oxyacetylene

76.

Spot welding electrodes should be


(a) Good conductor of Electricity

(b) Good conductor of

(c) High strength & Hardness

(d) Both (a) & (c)

heat

77.

In leftward welding
(a) Filler rod precedes torch
precedes filler rod
(c) A 60 V is prepared at the end of plate
(a) & (c)
78.

(b) Torch
(d) Both

The color of acetylene cylinder and oxygen cylinder is


(a) Maroon & Black
(b) Black & Maroon
(c) Yellow & Black
(d) Black & Yellow

79. Bi-Planer block in Chain assembly is used for changing the plane
of articulation through
(a) 120
(b) 90
(c) 180
(d) None
80.

For Non-reversible chains, mark the correct statement


(a)
Every third inner plate is extended in one direction
(b)
Every second outer plate is extended in one direction
(c)Every fourth outer plate is extended in both direction
(d)
All are wrong

PAPER - II
PART XII

ANSWERS:
1. A

2. D

3. B

4. B

5. D

6. C

7. A

8. D

9. A

10. C

11. D

12. A

13. D

14. D

15. C

16. C

17. D

18. C

19. B

20. A

21. D

22. A

23. C

24. B

25. B

26. A

27. A

28. B

29. D

30. A

31. B

32. D

33. C

34. A

35. D

36. C

37. D

38. D

39. A

40. A

41. B

42. C

43. C

44. C

45. D

46. B

47. A

48. D

49. D

50. A

51. B

52. C

53. D

54. D

55. B

56. A

57. D

58. A

59. D

60. A

61. B

62. C

63. D

64. C

65. A

66. C

67. C

68. A

69. B

70. C

71. B

72. C

73. A

74. D

75. A

76. D

77. A

78. A

79. B

80. B

PAPER - II
PART XIII
1. What percentage of manganese and sulfur will completely form
manganese sulfide in steel, which is harmless in small quantity:
(a) 0.3% Sulfur and 0.06% Manganese
(b) 0.30%
Manganese and 0.06% Sulfur
(c) 0.03% Sulfur and 0.06% Manganese
(d) None of these
2. It is a grey metal which impart hardness, strength, wear resistance
and corrosion resistance of steel:
(a) Chromium
(b) Nickel
(c) Silicon
(d)
Titanium
3. Which of the alloying element of steel is most expensive:
(a) Vanadium
(b) Titanium
(c) Molybdenum (d)
Tungsten
4. In SAE steel numbering system, first digit indicate:
a (a) Approximate percentage of predominant alloy
(b) Average carbon content
b (c) Type of steel
c (d) None of these
5. In SAE steel numbering system, last two or three digits indicate:
(a) Average carbon content
(b) Approximate percentage
of predominant alloy
(c) Type of steel
(d) Number of alloying
elements.
6. The numerals and digits for 1.25% Nickel, 0.60% Chromium of
Nickel-chromium steel in SAE numbering system is:
(a) 32xx
(b) 31xx
(c) 33xx
(d)
30xx
7. Military specification (MIL) are developed jointly by technical
services of Army, Navy and Air force and are issued by:
(a) American National Specification
(b) Munitions Board
Standard Agency
(c) American Military
(d) Air force-Navy
Specification Board

8. SAE 4037 steel is used for aircraft bolts, its AN specification is:
(a) AN-S-85
(b) AN-S-13-B
(c) AN-S-9a
(d)
QQ-S-624
9. While cooling the steel, its critical points are designated by:
(a) Ac3, Ac2,
(b) Ar3, Ar2,
(c) Arcm
(d) Ar3-2-1
10. At what percentage of carbon, all three critical points will merge
together and forms a single critical point known as Ar3-2-1
(a) 0.85%
(b) 0.65%
(c) 0.45%
(d) 0.25%
11. Steel below 0.85% carbon content is known as:
(a) Eutectoid
(b) Hypo-eutectoid
(c) Hypereutectoid
(d) None of these
12. Steel below 0.85% carbon content is composed of:
(a) Pearlite
(b) Pearlite with excess ferrite
(c) Pearlite with excess cementite
(d) Pearlite and
Austenit
13. While heat-treating the steel, transition from one form to another
can be arrested by:
(a) Slow rate of cooling
(b) Drastic rate of cooling
(c) Cooling in still air
(d) Cooling in furnace
14. Main constituent of Drawn (Tempered) steel is:
(a) Sorbite
(b) Martensite
(c) Troostite
(d) Austenite
15. To know the critical range of any steel, it is very much important to
know its:
(a) Critical points
(b) Upper critical point
(c) Lower critical point
(d) Chemical
composition
16. After heating the steel for annealing, the cooling is to be done:
(a) In the furnace
(b) In open air
(c) In oil
(d) Any one of these
17. In annealed state, aircraft steel is not of practical use because of:
(a) Its lowest strength
(b) Very hard and
brittle
(c) High ductility
(d) All of these
18. Type of annealing mainly used in sheet and wire industries:

(a) Full annealing


(c) Spheroidizing

(b) Process annealing


(d) Shop annealing

19. Hardening of the steel is done by:


(a) Heating above critical and cooling in furnace itself
(b)
Heating below critical range and quenching
(c)Heating above critical range and quenching
(d)
Any one of these
20. To maintain an oxygen free atmosphere inside the dry furnace, the
furnace is fed with:
(a) Ammonia gas
(b) Water vapor
(c) Carbon vapor
(d) Oil vapor
21. In liquid heat furnace, the parts are heated by:
(a) Oil bath
(b) Chemical bath
(c) Molten salt bath
(d) Any liquid
22. Re-arrangement of internal structure of steel complete in:
(a) Heating period
(b) Quenching period
(c) Soaking period
(d) Any one
23. Percentage of salt mixed with water to prepare brine is:
(a) 5 10%
(b) 10 15%
(c) 15 20%
(d) 20 25%
24. For oil quenching, the temperature of oil must be maintained:
(a) 70 1300F
(b) 75 1400F
(c) 80 1500F
0
(d) 85 160 F
25. For heat treating SAE 3140 Chrome-Nickel steel, the temperature
should be:
(a) 1200 12750 F
(b) 1250 13250F
(c) 1400
0
0
1500 F
(d) 1475 1525 F
26. Soaking period for HY-TUF special steel is two hours per inch of
thickness at a temperature of:
(a) 500 250F
(b) 550 250F
(c) 600 250F
(d) 650 250F
27. In case hardening, carbon content at the case will be:
(a) 0.60 0.80%
(b) 0.70 1.0%
(c) 0.80 1.25%
(d) 0.85 2%

28. For case hardening of aircraft work, the depth of case used is:
(a) 1/64 1/32 inch
(b) 1/48 1/25 inch
(c) 1/32 1/16 inch
1
1
(d) /16 /8 inch
29. For liquid carburizing, parts are heated in:
(a) Liquid furnace
(b) Gas furnace
(d) Electric furnace

(c) Molten salt bath

30. The sequence of case hardening consists of:


(a) Carburizing, tempering, case hardening and core refining
(b)
Carburizing, core refining, case hardening and tempering
(c)Carburizing, tempering, case hardening and core refining
(d)
Carburizing, case hardening, core refining and tempering
31. For selective case hardening, the portion of the parts not required
to be hardened, are:
(a) Jappaned
(b) Copper plated
(c) Left as it is
(d) None of these
32. Method of case hardening which increases compressive stress on
the skin and tensile stress just below the surface is:
(a) Selective case hardening
(b) Nitriding
(c) Shot peening
(d) Induction
hardening
33. While shaping of a metal if the sectional dimensions is 6X6 inches
or larger and approximately square, the shape is called:
(a) Slab
(b) Bloom
(c) Billet
(d) Rod
34. To get a fine grained structure, hot rolling must be finished:
(a) Below critical range
(b) Above critical range
(c) Within critical range
(d) Just below upper
critical point
35. The type of forging in which two dies are used, one is attached to
the hammer and other to anvil, is known as:
(a) Hammer forging
(b) Drop forging
(c) Cold forging
(d) Press forging
36. In metal powdered parts, property of the metal will be of:
(a) Particles of maximum quantity
(b)
Individual particles will held there property
(c)Uniform nature
(d)
None of these

37. Tensile strength of powdered metal parts can be obtained upto:


(a) 80% of solid metal parts
(b) 70% of solid metal
parts
(c) 90% of solid metal parts
(d) 95% of solid metal
parts
38. After hot rolling, it is necessary to cold roll:
(a) To avoid cracking
(b) To avoid scaling
(c) To avoid oxidation
(d) To impart smooth
surface and accurate dimensions
39. When cold drawing of wire, reduction in diameter in each draw can
be up to:
(a) 10%
(b) 20%
(c) 30%
(d) 40%
40. Fins and Laps is a type of defect in steel, which can occurs in
(a) Cold drawn seamless tube
(b) Rolling
(c) Ingots
(d) Forgings
41. If electrolyte from a lead acid battery is split in the battery
compartment, which procedure should be followed
(a) Apply boric acid solution to the affected area followed by the
water rinse
(b) Rinse the affected area thoroughly with the clean water.
(c) Apply sodium-bi-carbonate solution to the affected area followed
by the water rinse
(d) All of the above
42. Which of the following can provide the empty weight on an aircraft
if the aircrafts weight and balance record become lost, destroyed or
otherwise inaccurate
(a) Re-weighing the aircraft
(b) Aircraft
specification
(c) Type certificate datasheet
(d) Flight manual
43. The useful load of an aircraft consists of
(a) Crew, useable fuel, passengers and cargo
(b) Crew, useable fuel, oil and fixed equipments
(c) Crew, passengers, useable fuel, oil, cargo and fixed equipments
(d) None of the above
44. The maximum weight of an aircraft is

(a) Empty weight + crew, maximum fuel weight


(b) Maximum fuel weight, cargo, baggage and passenger
(c) Empty weight + crew, passengers and fixed equipments
(d) Empty weight + useful loads
45. Zero fuel weight is
(a) Dry weight + the weight of full crew, passenger and cargo
(b) Basic operating weight without crew, fuel and cargo
(c) Maximum permissible weight of a loaded aircraft without fuel
(d) None of the above
46. Amount of fuel used for computing empty weight and
corresponding C.G is
(a) Empty fuel tanks
(b) Useable fuel
(c) The amount of fuel necessary for half hour of operation
(d) Full tank fuel
47. Two boxes which weigh 10 pounds and 5 pounds are replaced in an
airplane so that their distance from C.G are 4 feet and 2 feet
respectively. How far forward of the C.G should a third box weighing
20 pounds be placed so that the C.G will not be changed.
(a) 3 feet
(b) 2.5 feet
(c) 3.5 feet
(d) 8 feet
48. Flexible hose used in aircraft system is classified with
(a) Outside diameter
(b) Wall thickness
(c) Inside diameter
(d) Outside dia-inside dia
49. Scratch or Nicks on the straight portion of aluminium alloy tubing
may be repaired if they are no deeper than
(a) 20% of the wall thickness
(b) 1/32 inch or 20% of wall thickness, whichever is less
(c) 10% of the wall thickness
(d) None of these
50. When installing bonded clamps to support metal tubing
(a) Paint should be removed
(b) Paint clamp and tube after installation
(c) Leave as it is
(d) Remove paint or anodizing from tube and clamp location
51. A 3/8 inch aircraft high pressure flexible hose as compare to 3.8
inch metal tubing used in the same system will

(a) Have about the same outer diameter


(b) Have equivalent flow characteristic
(c) Usually have interchangeable application
(d) Have same internal diameter
52. What method of magnetic particles inspection is used often to
inspect aircraft parts for invisible cracks
(a) Residual
(b) Inductance
(c) Intermittent
(d) Continuous
53. In performing a dye-penetrate inspection, the developer
(a) Act as blotter to produce a visible indication
(b) Seeps into a surface crack to indicate the presence of cracks
(c) Thoroughly cleans the surface prior to the inspection
(d) Perform no function
54. What type of corrosion attacks grain boundary of aluminium alloy
which are improperly or inadequately heat treated
(a) Filiform
(b) Intergranular
(c) Fretting
(d) Strain
55. Unless otherwise specified or required, aircraft bolts should be
installed so that the bolt head is
(a) Upward or in a forward direction
(b) Downward or in a forward direction
(c) Downward or in a rearward direction
(d) Upward or in a rearward direction
56. A bolt with a single raised dash on the head is classified as an
(a) AN corrosion resistance steel
(b) NAS standard aircraft bolt
(c) NAS closed tolerance bolt
(d) Magnetic resistance bolt
57. A bolt with an X-inside a triangle on the head is classified as an
(a) AN corrosion resistance steel bolt
(b) NAS aircraft bolt
(c) NAS closed tolerance bolt
(d) Aluminium bolt
58. Which tool can be used to measure the alignment of a rotor shaft
or the plain of rotation of a disc
(a) Dial indicator
(b) Shaft gauge
(c) Protector
(d) Micro meter

59. Weather waning tendency is greatest than taxying


(a) Either type of aeroplane in a quartering tail wind
(b) A tail wheel type aeroplane in a direct cross wind
(c) In a nose wheel type aeroplane quartering head wind
(d) A tail wheel type aeroplane parallel wind
60. When taxying an aircraft, an alternating red and green light from
the control tower means
(a) Move clear of the runway/taxy way immediately
(b) OK to proceed but used extreme caution
(c) Return to starting point
(d) Stop where are
61. The color of 100 ll fuel is
(a) Blue
(b) Colorless or straw
(d) Green

(c) Red

62. A fuel that does not vaporize readily enough can cause
(a) Vapour lock
(b) Detonation
(c) Hard
starting
(d) None
63. Nickel cadmium battery case and drain surfaces which have been
affected by electrolyte should be neutralized with a solution of
(a) Boric acid
(b) Sodium bi-carbonate
(c) Potassium hydroxide
(d) Sodium chloride
64. Corrosion caused by galvanic action is the result of
(a) Excessive Anodization
(b) Contact between two unlike metals
(c) Excessive etching
(d) Surface carburization
65. Which material is the most acidic
(a) Cadmium
(b) Magnesium

(c) Copper

66. Speed of sound in the atmosphere


(a) Varies according to the frequency of sound
(b) Varies according to the temperature
(c) Varies according to the pressure
(d) All of the above
67. Aspect ratio of a wing is defined as the ratio of
(a) Wing span to the wind root
(b) Square of the chord to the wing span
(c) Wing span to the mean chord

(d) Gold

68. A wing with a very high aspect ratio will have


(a) Low drag at high angles of attack
(b) A low stall speed
(c) Good control at low speed
(d) All of the above
69. Vicious cycle is connected to
(a) Nickel cadmium battery
(c) Dry cell

(b) Sulphuric acid battery


(d) None of the above

70. Basically corrosion reduces the strength of materials by the


process of
(a) Chemical reaction
(b) Electrochemical reaction
(c) Both (a) & (b)
(d) Electromagnetic process
71. Evidence corrosion on stainless steel is an appearance of
(a) Brown color rust
(b) Green color scum
(c) White color debris
(d) None of these
72. When corrosion product is removed from surface corrosion, then
which type of corrosion is appeared on it?
(a) Oxidation corrosion
(b) Dry corrosion
(c) Pitting corrosion
(d) Wet corrosion
73. The metal that is oxidized due to the corrosion attack that is called
as
(a) Neutralized agent
(b) Anodic change
(c) Cathodic change
(d) None of these
74. Mark the correct statement:
(a) Under corrosive environment, most active metal become
cathodic
(b) Under influence of corrosive agent less active metal become
anodic
(c) Established condition for corrosion due to the presence of anode
and cathode is called as local cell
(d) All of the above are true
75. Types of corrosion depends upon
(a) Type of materials
(c) Shape of metal

(b) Size of metal


(d) All of the above

76. Crevice corrosion is an example of


(a) Surface corrosion
(b) Concentration cell corrosion
(c) Electrolytic cell corrosion
(d) Exfoliation corrosion
77. Which type of corrosion occurs in high-strength materials used as
brackets, attached to Al-alloy skin of aircraft
(a) Galvanic corrosion
(b) Fretting corrosion
(c) Stress corrosion
(d) Dry corrosion
78. Coca is formed in which type of corrosion?
(a) Filiform corrosion
(b) Exfoliation corrosion
(c) Fretting corrosion
(d) Microbial corrosion
79. Which type of corrosion will occur in welded parts?
(a) Stress corrosion
(b) Inter-crystalline corrosion
(c) Fretting corrosion
(d) Dissimilar metal corrosion
80. Stress corrosion can be prevented by
(a) Shot-penning
(b) Shot-bursting
(c) As in (a) & increase in the fatigue strength
(d) As in (a) & increase in the tensile strength

PAPER - II
PART XIII
ANSWERS:
1. B

2. A

3. A

4. C

5. A

6. B

7. B

8. C

9. B

10. A

11. B

12. B

13. B

14. A

15. D

16. A

17. A

18. B

19. C

20. C

21. C

22. C

23. A

24. C

25. D

26. C

27. C

28. A

29. C

30. B

31. B

32. C

33. B

34. B

35. B

36. B

37. A

38. D

39. C

40. B

41. C

42. A

43. A

44. D

45. C

46. B

47. B

48. C

49. C

50. D

51. B

52. D

53. A

54. B

55. A

56. A

57. C

58. A

59. B

60. B

61. A

62. C

63. A

64. B

65. B

66. B

67. C

68. D

69. A

70. C

71. D

72. C

73. B

74. C

75. D

76. B

77. A

78. C

79. B

80. C

PAPER - II
PART XIV
1. Number of atoms in a Face Centered Cubic (FCC) crystal are:
(a) Fourteen
(b) Seventeen
(c) Nine
(d)
Fifteen
2. Type of bond forms in a material by loosing or gaining of electrons
is:
(a) Covalent Bond
(b) Ionic Bond
(c) Metallic Bond
(d) Secondary Bond
3. Hardness induced in a metal due to deformation is known as:
(a) Stress hardening
(b) Age hardening
(c) Work hardening
(d) None of these
4. When a metal is deformed plastically, forces required to deformed it
in reverse direction will be less, this is known as:
(a) Work hardening
(b) Bauschingers Effect(c) Strain aging
(d) None
5. Failure of component under high temperature and stress conditions
is known as:
(a) Creep fracture
(b) Ductile fracture
(c) Fatigue
fracture
(d) Brittle fracture
6. (1) An intermetallic compound is a form of alloy, where as
(2) Substitutional solid solution is a type of solid solution
(a) 1 is correct & 2 is incorrect
(b) 2 is correct & one is incorrect
(c) Both (1) and (2) are incorrect
(d) Both, (1) and (2) are correct
7. Iron changes its forms at different temperatures, thats why it is
known as :
(a) Ferrous metal
(b) Magnetic metal
(c) Allotropic
(d) None of these
8. Ductility of a material is its property to be drawn into:
(a) Wire
(b) Sheet
(c) Tubes (d) Both (a) and (c)

9. Strength is the ability of a material to resist external loads where as


toughness is to:
(a) Resist fracture
(b) Resist deflection
(c) Resist elastic deformation
(d) Withstand bending or torsion without fracture
10. Treatment given to a metal to relieve internal stresses and induce
softness is:
(a) Tempering
(b) Hardening
(c) Normalizing
(d) Annealing
11. Maximum load per square inch a material can with stand is:
(a) Yield strength
(b) Tensile strength
(c) Proof
stress
(d) Elasticity
12. A series of heating and cooling to improve physical properties of a
metal is known as:
(a) Normalizing
(b) Hardening
(c) Tempering
(d) Heat treatment
13. Specimen is tested for which strength during tensile testing
(a) Proof stress
(b) Fatigue strength
(c) as in a and Yield strength
(d) as in c and
Ultimate Tensile Strength
14. (1) For tensile testing the specimen must be straight
(2) Specimen can be straighten by hammering or bending.
(a) (1) is true and (2) is false
(b) (2) is true and (1)
is false
(c) Both (1) and (2) are true
(c) Both (1) and (2)
are false
15. Proof stress is the stress at which a permanent set occurs:
(a) 0.001 inch per inch of gauge length
(b) 0.0001 inch per inch of gauge length
(c) 0.00001 inch per inch of gauge length
(d) 0.01 inch per inch of gauge length
16. (1) For checking elastic limit, load can be released upto zero,
where as
(2) For checking proof stress load is released up to 20%
(a) (1) is true and (2) is false
(b) (2) is true and (1) is false
(c) Both (1) and (2) are true
(d) Both (1) and (2) are false

17. Yield point of a metal can be determined by:


(a) Divider method
(b) Set method
(c) Extension under load method
(d) both (b) and
(c)
18. For checking the area of depression in Brinell Hardness Test,
Accuracy of microscope should be:
(a) 0.05mm
(b) 0.005mm
(c) 0.5mm
(d)
0.0005mm
19. In Rockwell Hardness Test, if B scale is used for material harder
than B-100
(a) It will give inaccurate reading
(b) Ball may get
flattened
(c) No reading will be their
(d) None of these
20. To locate a defect in a material with the help of magnaflux test, it
is essential that the magnetic lines of force pass approximately
(a) Parallel to defect
(b) Perpendicular to defect
(c) Any direction of defect
(d) Both (a) and (b) are
correct
21. Number of atoms in a Hexagonal Closed Pack (HCP) crystal are:
(a) Fourteen
(b) Nine
(c) Eleven
(d)
Seventeen
22. Bonds formed in materials due to Vander Walls forces of
attraction, is:
(a) Ionic bond
(b) Covalent bond
(c) Mettalic bond (d)
Secondary bond
23. Elastic limit of a material is considered to have been reached if a
permanent set obtained is:
(a) 0.0003 inch
(b) 0.00002 inch
(c) 0.00001 inch
(d) 0.00004 inch
24. Proof stress of a specimen of 2 inch gage length will be at a
permanent set of:
(a) 0.0004 inch
(b) 0.0003 inch
(c) 0.0002 inch
(d) 0.0001 inch

25. For Brinell Hardness Testing, application of load should be for at


least:
(a) 20 second
(b) 15 second
(c) 10 second
(d) 5 second
26. In Rockwell hardness test, red dial is used for:
(a) Ball penetrator
(b) Diamond point penetrator
(c) both (a) and (b)

(d) None

27. In Rockwell hardness test, combination used for aircraft material


are:
(a) A and B
(b) C and D
(c) A and D
(d) B and C
28. In Rockwell hardness test, the working range of C scale is:
(a) C10 & upward
(b) C15 & upward
(c) C20 & upward
(d) C25 & upward
29. In Rockwell hardness test, a ball penetrator as large as inch
diameter should be used for soft metal with:
(a) 60kg load
(b) 20kg load
(c) 100kg load
(d) 150kg load
30. Load applied for soft material in Vickers hardness test is:
(a) 20 kg
(b) 15 kg
(c) 10 kg
(d) 5 kg
31. For bending test, the diameter of the pin over which bend is to be
performed, should be:
a (a) Equal to the diameter of the test specimen
b (b) Equal to the thickness of the material
(c)Equal to diameter of thickness of the test specimen
(d)
None of these
32. For bending test of forging stock specimen, the corners are to be:
(a) Made round
(b) Broken by file
1
(c) Rounded to /16 inch radius
(d) None of these
33. The jaws of the vice are to be rounded for reverse bending test:
c (a) 3/16 inch radius for wire above 3/16 inch diameter
d (b) 3/16 inch for wire below 3/16 inch diameter
e (c) 3/16 inch radius up to 3/16 inch wire
f (d) None of these

34. In charpy impact test, the V notch of the specimen faces:


(a) Opposite to the pendulum
(b) Towards the pendulum
(c) Above the jaws
(d) None of these
35. When carrying out crushing test on aircraft tubing, the tube should
be in:
(a) Annealed condition
(b) Normalized
condition
(c) Heat treated condition
(d) Any one of these
36. Specimen required for torsion testing of wire less than 0.033 inch
diameter:
(a) 10 inch
(b) 20 inch
(c) 30 inch
(d) 40 inch
37. Specimen required for torsion testing of wire more then 0.033 inch
diameter:
(a) 10 inch
(b) 20 inch
(c) 30 inch
(d) 40 inch
38. X-rays are used efficiently for the inspection of steel parts upto
thickness of:
(a) 8 inch
(b) 6 inch
(c) 3 inch
(d) 2
inch
39. (1) Sulfur is a harmful impurity in plain carbon steel
(2) Phosphorus is very much useful element of plain carbon steel
(a) Both are true
(b) Both are false
(c) (1) is true (2) is false
(d) (1) is false and (2)
is true
40. Presence of manganese in steel is mainly to
(a) Eliminate ferrous oxide
(b) Improve forging quality
(c) Induce penetration hardness
(d) All of these
41. In tapered sectioned metal piece, which area is more susceptible
to corrosion
(a) Exterior surface
(b) Interior surface
(c) Thin portion
(d) Thick portion
42. Mark the correct statement:
(a) Inter-crystalline corrosion occurs along grain boundaries of an
alloy

(b) This is a from of electrochemical attack


(c) As in (b) & occurs due to lack of uniformity
(d )All of the above
43. Stress corrosion can be detected by
(a) Eddy current
(c) X-ray

(b) Dye-penetrant
(d) Ultrasonic method

44. Speed of electro-chemical attack is increased in _________


climate
(a) Hot and dry
(b) Cold and moist
(c) Hot & moist
(d) Cold & dry
45. Which type of acid is produced by electrical sparks when combined
with moisture in confined spaces?
(a) Sulphuric acid
(b) Nitric acid
(c) Phosphoric acid
(d) Chromic acid
46. Which type of corrosion is present in contact area of metal and
non-metal joint?
(a) O2 concentration cell corrosion
(b) Metal ion concentration cell corrosion
(c) Filiform corrosion
(d) Crevice corrosion

47. Mark the correct statement:


(a) The fungus grows at the fuel/water interface
(b) As in (a) & temperature range is in between 50-60F.
(c) As in (b) & this occurs in integral fuel tank
(d) As in (c) & this produces a microbial corrosion
48. Which corrosion is occurred due to improper heat-treatment and
welding defects?
(a) Metabolic corrosion
(b) Inter-granular
corrosion
(c) Trans-granular corrosion
(d) Weld decay
corrosion
49. Which of the following coating function as sacrificial protection?
(a) Chromium plating
(b) Galvanizing
(c) Cladding
(d) Metal spraying

50. Which nut is used to prevent other nuts from turning on threaded
bolt or rod
(a) Self-locking nut
(b) Jamb but
(c) Stainless steel nut with cotter pin
(d) None of these
51. The content of CO2 fire extinguisher or N2 pressurized extinguisher
is checked by
(a) Weight and pressure gauge
(b) Marking on
neck
(c) By operating the extinguisher
(d) All of
the above
52. Choose incorrect statement:
(a) Yellow polypropylene provide insufficient strength
(b) Proper tension in rope allows 1 movement
(c) Manila rope requires extra slack due to shrinks
(d) The rope requires extra slack due to shrinks
53. Which type of jack is used for L/G retraction check
(a) Single base jack
(b) Bottle neck jack
(c) Screw jack
(d) Tripod jack
54. Which measuring tool is used for outside or inside measurement
for faster work
(a) Vernier micrometer
(b) Vernier caliper
(c) Micrometer caliper
(d) None of these
55. Which is incorrect statement
(a) If corrosion is present in control cable should be replaced
(b) Cable used in seaplane must be coated with para-ketone
(c) For detection of corrosion, cable twist in same way of lay
(d) Carbon steel cable must be used with protective coating
56. After welding aluminium parts flux should be removed by
(a) Immersing them in like warm water for 30 minutes
(b) Mechanical means, i.e. wire brushing as the flux is not soluble
in water
(c) Washing the parts in boiling water containing 5% HNO 3
(d) Vacuum blasting
57. A gusset is
(a) A bracing between longerons
connecting bracket

(b) A type of

(c) Used for fail safe construction


plate

(d) Like a butt

58. The unit where calculations are preferred is called


(a) Central processing unit (CPU)
(b) Control
Unit
(c) Arithmetic and logic unit (ALU)
(d) Computing
unit
59. EDP stands for
(a) Electrical data processing
data processing
(c) Entry data processing
discrete programme

(b) Electronic
(d) Electronic

60. Assembler is
(a) An individual who assembles computer
(b) Language
(c) Program
(d) None of the above
61. Input unit of computer communicates between
(a) Operator and Computer
printer
(c) CPU with monitor
Computer

(b) Memory with


(d) Output and

62. The symbol for Hexadecimal is


(a) 2
(b) 8
(c) 10

(d) 16

63. In computer terminology, MICR means


(a) Magnetic Ink Character Recognition
(b) Magnetic Ink Computer Recognition
(c) Monitor Indicating Computer Relay
(d) Mass Information Computer Record
64. Speed of processor is measured in
(a) Kilobit / Sec
(b) Hertz
RPM

(c) Byte

(d)

65. A byte is a group of


(a) 2 bits
16 bits

(c) 8 bits

(d)

(b) 4 bits

66. In digital computer system, number of states used is


(a) 2
(b) 3
(c) 8

(d) 16

67. The term ROM means


(a) Random Operation Memory
Operate Memory
(c) Read only Memory

(d) Read and


(d) None

68. The energy of a capacitor having capacitance C and voltage V is


given by
(a) 0.5 CV2
(b) CV
(c) C2V
2
(d) 0.5 C V
69. One unit of magnetic flux is given by
(a) Weber
square
(c) Square root of Weber

(b) Weber per meter


(d) Henery

70. Generators works on the principle of


(a) Faradays law of electromagnetic induction
(b) Ohms law
(c) Biot - severts law
(d) Gausss law
71. The Capacitor of a parallel plate is given by
(a) Ac / d
(b) A2C / d
(c) Ad / c
None

(d)

72. If there are N number of cells, each having voltage E and internal
resistance r are connected in series, then the resulting e.m.f of the
circuit is given by
(a) NE volt
(b) E/N volt
(c) E volt
(d)
NEr volt
73. The phase difference between voltage and current in a purely
resistive circuit is given by
(a) 0
(b) 90
(c) 45
(d) 135
74. One micro farad is equal to
(a) 0.001 milli farad
(c) 1000 milli farad

(b) 100 milli farad


(d) 10 milli farad

75. The ability of magnet to restore magnetism is called


(a) Retentivity
(b) Permitivity
(c) Store ability
(d) both (a) & (c)

76. If Im is the maximum current for sine AC then its R.M.S value is
given by
(a) 0.707 Im
(b) Im
(c) 0.5 Im
(d) 1.414 Im
77. The relationship between voltage and current in a purely inductive
circuit is given by
(a) Voltage leads the current by 90
(b) Current lags the voltage by 90
(c) both (a) & (b)
(d) None of the above
78. By voltage division rule the voltage drop V1 in the circuit will be
(a) V1 = (R2 x Vs) / (R1+R2)
(b) V1 = (R1 x Vs) / (R1+R2)
(c) V1 = Vs x (R1+R2) / R1
(d) None
79. If inductance is doubled and the capacitance is halved , then
resonant frequency F0
(a) Doubled
(b) Halved
(c) Remains same
(d) Squared root of F0
80. 50000000 Hz stands for
(a) 5 MHz
(d) 500 MHz

(b) 0.5 MHz

(c) 50MHz

PAPER - II
PART XIV
ANSWERS:
1. A

2. B

3. C

4. B

5. A

6. D

7. C

8. D

9. D

10. D

11. B

12. D

13. D

14. A

15. B

16. D

17. A

18. A

19. B

20. B

21. D

22. D

23. A

24. C

25. C

26. A

27. D

28. C

29. A

30. D

31. C

32. C

33. C

34. A

35. A

36. C

37. A

38. C

39. C

40. D

41. D

42. D

43. B

44. C

45. B

46. D

47. A

48. B

49. C

50. B

51. A

52. A

53. D

54. B

55. C

56. C

57. B

58. C

59. B

60. C

61. A

62. D

63. A

64. B

65. C

66. A

67. C

68. A

69. A

70. A

71. A

72. A

73. A

74. A

75. A

76. A

77. C

78. B

79. C

80. C

PAPER - II
PART XV
1. The purpose of turnbuckle is to
(a) make minor adjustment in cable length
tension
(c) both (a) & (b)

(b) adjust cable


(d) none

2. The major alloying element in 7075 Al-alloy is


(a) magnesium
(b) silicon
(c) magnesium &
silicon
d) Zinc
3. T-6 designation of Al-alloy indicates
(a)
solution heat treated and then artificially aged.
(b)
solution heat treated and then stabilized.
(c)
artificially aged only.
(d)
solution heat treated and then cold worked.
4. Meshing gear have same
(a) teeth
(b) pitch of same size
(c) dedendum
(d) all
5. Vernier scale is used on
(a) micrometer
(b) boroscope
(c) spheroscope
(d) all
6. Fibre glass is also known as
(a) E glass or Electric glass
(c) both (a) & (b)

(b) S glass or Borosile glass


(d) All

7. Well threads are


(a) detection for warp direction
(c) bias

(b) direction is 45 to warp


(d) perpendicular to warp

8. Strength of composite depends upon


(a) type of fiber
(b) process of manufacture
(c) heat treatment
(d) all
9. Which statement is correct?
(a)
Force is exhorted on uncharged particle.
(b)
Force is applied on charged particle moving along the
magnetic field.

(c)Both (a) & (b)


10. When two sphere are of same mass, one is positive charge and
the other is negative charge then new mass will remain
(a) change
(b) unchanged
(c) sum of
both mass
11. If the conductor is of 4 and if it is stretched to twice its length
then its resistance is
(a) 1
(b) 2
(c) 16
(d)
32
12. A & B are big and small battery having same emf internal
resistance of battery A is
(a) less than B
(b) greater than B
(c) equal to B
(d) unaffected
13. Which statement is correct?
(a)
Battery terminal voltage is equal to battery emf.
(b)
Battery terminal voltage is less than battery emf.
(c)Battery terminal voltage is more than battery emf.
(d)
Depends on direction of current flow.
14. In flourescent method
(a)
if wet developer is applied, it must be dried.
(b)
if wet developer is applied, it must not be dried.
(c)dry for long period.
(d)
none
15. Telescoping gage
(a) is used for inside diameter
6
(c) range from to 1

(b) range from to


(d) both (a) & (b)

16. Whole gage is used for measuring


(a) Grooves and slots
(b) small hole
& (b)
(d) none

(c) both (a)

17. The size of flat cold chisel is determined by


(a) width of cutting edge
(b) length of cutting
edge
(c) length of chisel
(d) all
18. Thread may be produced by
(a)
on a lathe with specially shaped cutting tool.

(b)
on spiral machine using rotary cutter (Tapes).
(c)by rolling on spiral machine using dies.
(d)
all.
19. Needle file are
(a) knurled on both sides
one side
(c) used on slot by dye maker and watch maker
(b) & (c)

(b) knurled on
(d) both

20. Hook spinner is used on


(a)
round nut having series of knotches or slots cuts on its
side.
(b)
hexagonal nuts with slots.
(c)octagonal nut with slots.
(d)
all.
21. Muntz metal is used
(a) to make oil and hydraulic fitting.
(b) nuts and bolts for used in salty atmosphere.
(c) nuts and bolts which are not affected by fresh water.
(d) none.
22. Al weldable material is
(a) 2 S
(b) 17 S

(c) 52 S

(d) 53 S

23. A punch made of tool steel is heat treated to


(a) heat to cherry red colour
(b) as in (a) & dipped
in sand
(c) heat to dazzling white
(d) as in (b) & heat to
purple colour
24. Computer performs only the calculation i.e.
(a) simple

(b) complex

(c) problem with split into number of logic step

(d) none

25. High discharge tester is used to check the


(a)
voltage of battery in normal operating condition.
(b)
efficiency of condenser.
(c)generator output.
(d)
voltage of battery to find its charge condition and whether
recharging is required.
26.

Electrical power and energy is expressed in terms of

(a) Kilo Watt and Kilo Watt Hour respectively


(b) Watt and Joule respectively
(c) Watt and Watt Per Hour respectively
and Newton

(d) Watt

27. Three phase winding rotate with 1800 rpm in magnetic field
having 8 poles, its frequency will be
(a) 120 Cycle/Sec
(b) 800 Cycles/
Sec
(c) 1200 Cycles/ Sec
(d) 1800 Cycles/ Sec
28. Titanium is heat treated for following purpose
(a)
Thermal hardening to improve strength.
(b)
Annealing offer hot working and cold working to provide
maximum ductility for subsequent cold working.
(c)Both (a) & (b).
(d)
None.
29. The normal solder technique of Al is
(a)
similar to that of other material.
(b)
differ to control the expansion and contraction of matter.
(c)differ to the extent a low heat input is required.
(d)
both (b) & (c) are correct.
30. Flux is used in wielding of Al alloy for
(a) better penetration
(b) rid to oxidation
(c) for better fusion
(d) slow down the flow of molten
metal
31. Flux used in silver soldering is
(a) zinc chloride
(c) sulphuric acid
32. Rust in steel is removed by
(a) wire brush
(b) emery paper
blasting (d) all

(b) ortho phospheric acid


(d) all are correct
(c) control sand

33. Barcol tester is used on


(a) harder material
(b) softer material
of material
(d) none
34. I-Beam is produced by
(a) extruding
(b) forging
35.

Which one is stable wrought alloy

(c) casting

(c) all type

(d) rolling

(a) piston
(d) Al-clad

(b) cylinder head (c) crank shaft

36. The load per unit square inch at which material breaks
(a) ultimate tensile strength
(b) yield point
(c) tensile strength
(d) all are correct
37. The ultrasonic testing is used to check
(a) fatigue crack
(c) void and inclusion on cast

(b) disbond
(d) all are correct

38. Which statement is correct regarding sensitivity of x-rays?


(a)
The darkness of ratio graph does not depends on the
radiation penetrating in the cylinder.
(b)
Thicker the specimen, lighter the image.
(c)Thicker the specimen, darker the image.
(d)
None.
39. If information of physical data is large such as in altimeter,
display is known as
(a) long range display
(b) short range display
(c) smooth range display
(d) wide range display
40. Nick name of digital display is
(a) alphanumeric display
display
(c) circular scale display
display

(b) straight scale


(d) platform scale

41. The soldering of Al-alloy differs from another metal due to


(a) high specific heat and conduction
(b) greater heat
input
(c) uneven expansion and contraction avoided
(d) all
42. Kirchoffs Law is applicable to
(a) DC
(b) AC
resistance
(d) AC & DC

(c) DC circuit having

43. In modulation, the available band is


(a) one
(b) two
(c) no band
band

(d) many

44. The modulation in which, amplitude is kept constant and


frequency is changed is called

(a) amplitude modulation


(c) frequency modulation

(b) space modulation


(d) phase modulation

45. Angle of attack is the


(a)
acute angle between aircraft longitudinal axis and cord line
to which aerofoil is mounted on the aircraft.
(b)
horizontal acute angle between the symmetry of aircraft
and wind direction from which it touches the aircraft.
(c)acute angle between the symmetry of the aircraft and the cord
line of the aerofoil section.
(d)
all.
46. In NDT of material by dye pentrant inspection, the volume of
defect is interpreted by
(a) staining rate
(b) staining speed
(c) staining
extent
(d) all
47. In ultrasonic test scanning is carried out by moving both probes
simultaneously in opposite direction for
(a) flash butt joint (Welding)
(b) heavy forging
(c) heat treatment defect
(d) thickness
measurement
48. During fuelling the most necessary precaution to be observed
(a)
grounding connection first made to aircraft and then
fuelling vehicle.
(b)
Grounding connection first made to fuelling vehicle and
then the aircraft.
(c)Either (a) or (b)
49. The fluid is used for all type of aircraft engine except rocket is
(a) gasoline
(b) air
(c) aviation turbine fuel (d)
all of the above
50. In composite the strength is provided by
(a) reinforced fibre (b) core
(c) resin
fabric use

(d) as in (a) and

51. In hardness testing of composite the hardness is measured


(a) resin
(b) reinforcing fibre
(c) by the use of specific chart
(d) both (b) & (c)
52. In composites repair the part is steeped rather than to be
scarfed for

(a) uniform sheer stress


stress
(c) smoothness

(b) uniform tensile


(d) both (a) & (b)

53. In uniform fluid flow, the fluid is first made to flow through tube
and the pressure exerted by the fluid is measured by
(a) dynamic pressure
(b) static pressure
(c)
Reynolds no. (d) all
54. PARKETON is used for protection of
(a) steel
(b) numinium
(d) as in (a) and cable

(c) Mg

55. The rust and corrosion is removed from highly stressed steel
parts by
(a) abrasive paper
(b) fine buffling clothron buffling wheel
(c) wire brush
(d) all
56. Centre drill is used to produce
(a) short hole and CSK hole (counter sunk)
and large hole
(c) both (a) & (b)

(b) short hole


(d) all

57. During repair procedure of composite part treatment is done for


(a) small dis bands
(b) restore surface
protection
(c) seal honey comb casting
(d) none
58. Synthetic rubber used in the aircraft is designated GRM as
(a) poly-sulphide polymer
(b) isobutylene
(c) complex of butylenes and cresylonitrile
(d)
Governemtn rubber mono-vinyl acetylene or neropene
59. To pentralise the surface of Ni-Cd battery compartment
(a) boric acid
(b) water
(c) backing soda
all

(d)

60. Close tolerance bolt is identified by


(a) triangle marking on head
(b) crossed triangle
marking on head
(c) circle marking on head
(d) triangle on head with plus
marking within it.

61. While jacking, the approved procedure is


(a) both wheels are raised together.
(b) wheels are raised one after another.
(c) A/C should be raised through designated point only.
(d) both (a) & (c).
62. The class of fit required for a tight drive fit is
(a) class-1
(b) class-2
(c) class-3
class-4

(d)

63. Piston engines mechanical efficiency differs due to


(a) difference of pressure
(b) difference of
temperature
(c) difference of grade of fuel used
(d) difference in mass
of fuel
64. A device which gives lateral control and is mounted at the upper
surface of wing
(a) spoiler
(b) vertex generator
(c) tab
(d) flap
65. The pressure of water in composite can be detected by
(a) USI
(b) DPI
(c) Endoscope
Radiography

(d)

66. Aircraft bolts are generally manufactured with a


(a) class-1 fit for the threads
(b) class-2 fit for the
threads
(c) class-3 fit for the threads
(d) class-4 fit for the
threads
67. The hose of 100 LL AVGAS dispense is
(a) red
(b) blue
(c) black
68. Which is low energy logic circuit?
(a) TTl
(b) ECL
(c) both (a) & (c)

(d) green
(d) none

69. Metal matrix composite is a recent conception materials where in


(a)
resin is reinforced with metal.
(b)
resin and fibre are reinforced with metal.
(c)fibres are reinforced with metal during molten stage.
(d)
all of the above.

70. Two wires each one meter long are kept at a distance of 0.02mt.
apart. If 1 amp current is flowing through each wire, then force
acting in the wire will be
(a)
attractive if the direction of the current flowing through
wires is same.
(b)
attractive if the direction of the current will be opposite.
(c)repulsive if direction of the current will be reverse.
(d)
Both (b) and (c) are correct.
71.

The symbol represents

(a) SCR, rheostat respectively


(b) rheostat,
thyristor respectively
(c) resistor, FET (field effect transistor) respectively
(d) none of
the above
72. In which condition the bridge is said to be balance?
(a) R1 is increased, R2 is decreased
(b) R3 is increased, R4
is decreased
(c) R2 is increased, R3 is decreased
(d) when G is constant
73. Mark the wrong statement.
(a)
Helicoils are made of 18-8 stainless steel.
(b)
Screws come in AN 500 and NS 200 series.
(c) Diameter of nut is measured in 16th of an inch.
(d)
Lockwashers should be used only with secondary structure
not with primary structure.
74. In case of battery which of the following quantity can be stored?
(a) energy
(b) charge
(c) current
(d) none of
the above
75. In a dry cell battery
(a)
carbon electrode is placed centrally surrounded by
aluminium chloride electrolyte.
(b)
zinc chloride is placed centrally surrounded by aluminium
chloride electrolyte.
(c)carbon electrode is placed centrally surrounded by zinc chloride
electrolyte.

(d)

both (a) and (c) are correct.

76. The identical insulated wire coils are hung from air so that they
are facing each other and supplied with same direction a.c.
(a) both are attracted to each other
(b) both are
repelled
(c) clockwise rotation
(d) anticlockwise
rotation
77. Hot water quenching
(a)
minimize distortion and elevated cracking.
(b)
Ensures maximum resistance to corrosion.
(c)Minimizes distortion but results in cracking.
(d)
(a) & (b) are correct.
78. In gas welding of oxygen and acetylene regulators has
(a)
left hand thread and right hand thread respectively.
(b)
right hand thread and left hand thread respectively.
(c)both have left hand thread.
(d)
both have right hand thread.
79. Pull thru rivets are fabricated in two common head styles
(a) universal head
(b) brazier head
(c) 100 countersunk head
(d) both (a) & (c) are correct
80. A rivet head having raised across indicating
(a) 5056 T
(b) 2024 T
(c) carbon steel
corrosive resistant steel

(d)

PAPER - II
PART XV
ANSWER :
1. C

2. D

3. A

4. B

5. A

6. A

7. D

8. D

9. B

10. B

11. C

12. A

13. B

14. A

15. D

16. C

17. A

18. D

19. D

20. A

21. B

22. C

23. A

24. C

25. D

26. B

27. A

28. C

29. B

30. B

31. A

32. D

33. B

34. D

35. D

36. A

37. D

38. B

39. A

40. A

41. B

42. D

43. D

44. C

45. B

46. C

47. A

48. B

49. B

50. D

51. D

52. B

53. A

54. D

55. B

56. A

57. B

58. D

59. A

60. B

61. D

62. D

63. C

64. A

65. D

66. C

67. B

68. A

69. C

70. A

71. A

72. D

73. D

74. B

75. D

76. A

77. A

78. B

79. D

80. A

PAPER - II
PART XVI
1. Rheostat varies
(a) amount of current
(c) both (a) & (b)

(b) amount of voltage


(d) none

2. Potentiometer varies
(a) amount of current
(c) both (a) & (b)

(b) amount of voltage


(d) none

3. At the center of a coil, amount of flux is concentrated maximum at


(a) starting of a coil
(b) end of a coil
(c) center of a coil
(d) remain equal at all
places
4. Negative plate of lead acid battery is
(a) lead
(b) lead peroxide
spongy lead

(c) lead sulphide

(d)

5. Plates of lead acid battery is made of


(a)
lead + antimony on which active material is attached.
(b)
lead + iron on which active material is attached.
(c)antimony + iron on which active material is attached.
(d)
none
6. m.m.f. is measured in Gilbert and symbolized by the capital letter.
(a) G
(b) F
(c) M
(d) W
7. Solenoid relay is operated on
(a) high current
(b) low current
(d) low voltage

(c) high voltage

8. Construction of separator of a lead acid battery is made in such a


way that it circulates the electrolyte freely around the plates in
addition it also provides a path for sediments to settle.
(a) at the side of cell
(b) at the top of cell
(c) at the bottom of cell
(d) none
9. Thermal protector is used to
(a) protect a motor
automatically

(b) to open the circuit

(c) it operates when temperature is very high


above

(d) all of the

10. S/W designed for momentarily operation


(a) micro s/w
(b) push button s/w
(d) none

(c) toggle s/w

11. Rotary S/W are used in


(a) voltmeter selector s/w
(d) none

(c) both (a) & (b)

(b) ignition s/w

12. Starter relay s/w is made to operate


(a) intermitenty
continuously
(c) could cause over heating if operated continuously
both (a) and (c)

(b)
(d)

13. Oil capacitors generally restricted to be used in


(a) radio transmitting equipment
(b) radar
transmitting equipment
(c) both
(d) none
14. In fixed mica capacitor the dielectric is made of
(a) metal plate
(b) mica
(c) both (a) & (b)
(d) none
15. Mica prevents as a dielectric
(a) arching between the plates
higher voltage
(c) both (a) & (b)

(b) can withstand


(d) none of these

16. The capacitor which provides large capacitance in small physical


size is
(a) oil capacitor
(b) mica capacitor
(c) electrolytic capacitor

(d) paper capacitor

17. Wet-electrolytic capacitors must be mounted on


(a) horizontally
(b) vertically
(c) any position
(d) none
18. The working voltage of a capacitor depends on
(a) type of material used as a di-electric
(b) thickness of
di-electric
(c) frequency
(d) all of the above

19. The working voltage of a capacitor should be at least


(a) 50% greater than highest voltage applied.
(b) 60% greater than highest voltage applied.
(c) 70% greater than highest voltage applied
(d) none
20. To prevent the entry of water and other foreign matter, the pilot
pressure tube is provided with
(a) mast
(b) baffles
(c) drain hole
(d)
moisture trap
21. If at mean sea level ambient temperature decreases than ICAO
standard atmosphere
(a) altimeter under read
(b) altimeter over read
(c) no indication error
22. In order to compensate for barometric error i.e. altitude error
due to atmospheric pressure change an altimeter is incorporated
with
(a) capsule of suitable material
(b) bimetallic strip
(c) barometric pressure setting device
(d) hair spring
23. The tropopause marks the point at which
(a)
air pressure stops decreasing (with increasing altitude) and
remains constant.
(b)
air temperature starts increasing
(c)air temperature reaches to freezing point temperature
24. Fuel pressure indicator is the means for
(a) warning for low pressure.
(b) warning for high pressure.
(c) as in (a) & indicate pressure at which fuel is being supplied.
(d)
as in (b) & indicate pressure at which fuel is being
supplied.
25. In square law compensating devices, the principle being made in
use is that the length of lever is altered as progressive deflection of
the capsule takes place causing the
(a)
mechanism & pointer movement to be increased for small
deflection and decreased for large deflection.
(b)
mechanism & pointer movement to be decreased for small
deflection and increased for large deflection.
(c)either (a) or (b).
(d)
none of these.

26. A mechmeter is a compound flight instrument and uses the


following mechanism to compute the required ratio.
(a) air speed mechanism
(b) altitude mechanism
(c) either (a) or (b)
(d) both (a) & (b)
27. In vertical speed indicator (VSI) during descent the capsule will
(a) expand
(b) contract
(c) no effect
28. During a descent, the static vent become blocked by ice, the air
speed indicator will
(a)
under read due to static pressure increasing.
(b)
fall rapidly to zero due to differential pressure equalizing.
(c)over read due to static pressure increasing.
(d)
continue to indicate correctly because the instrument only
uses pilot pressure.
29. The number, size and disposition of shock proff mounting
requires are governed by
(a)
the size of the panel.
(b)
number of instrument to be installed.
(c) as in (a) & the distribution of the total weight.
(d) as in (a) & (b).
30. Micro desynn synchronous data transmission system is used for
(a) air brake, flap position indication
(b) oil or fuel pressure
indication
(c) liquid content indication
(d) none of the above
31. An aircraft is flying a constant rate of descent at 650 fpm when
the static vents become blocked by ice. A few seconds after the
blockage occurs the most likely VSI indication will be
(a) zero
(b) 550 fpm descent
(c) 650 fpm descent (d)
750 fpm descent
32. In TSI, the slip indicator is of the ball and liquid filled tube type
the liquid used is
(a) silicon fluid
(b) alcohol
(c) white spirit
33. The Bristol modified method is an adoption of
(a) hot fluid method
(b) cold fluid method
(c) oil & chalk process
(d) both (a) & (b)
34.

In the hot fluid method, the oil used may be

(a)
28% lard oil (by volume) in paraffin.
(b)
as in (a) or 3 parts of paraffin & 1 part lubricating oil.
(c)as in (b) or 50% paraffin oil & 50% spindle oil.
(d)
none of these.
35. Dye-penetrant method is not applicable on
(a) ceramics
(b) moulded nibber
(d) all of these

(c) plexi-glass

36. Dye-penetrant method is used for finding out


(a) cracks
(b) porosity
(c) defects open to the
surface (d) all of these
37. To avoid the risk of corrosion, dye-penetrant test of magnesium
alloys are done after
(a) anodising
(b) chromatizing
(c) carburizing
(d) parcolubrizing
38. In dye-penetrant method, the penetrant time does not depend
upon
(a) the characteristics of process being used
(b) the size of
parts
(c) the temperature of parts and dye
(d) none of these
39. Mark the correct statement regarding dye-penetrant method
(a)
the shallow cracks indication takes less time where as
normal cracks indication takes more time.
(b)
the rate of staining is an indication of volume where as the
extent of staining is an indication of width and depth of defect.
(c)scattered dots of dye indicate fine porosity or pitting where as
gross porosity may result in an entire area becoming stained.
(d)
all of these.
40. Surface defects are best detected by
(a) dye penetrant method
(b) eddy current method
radiography
(d) all of these

(c)

41. The penetration power of X-rays increases with an increase in


(a) voltage
(b) frequency
(c) wave length
(d) both (a) & (b)
42. Fluroscopy is applicable to
(a) normal Y-ray sources
(c) X-rays

(b) low energy X-rays


(d) both (a) & (b)

43. The degree of blackening of radiograph is


(a) contrast
(b) definition
(c) density
penumbra

(d)

44. The sharpness of image details on a radiograph is


(a) density
(b) definition
(c) resolution
(d) contrast
45. Blurring at the edges of a radiographic image due to the
radiation source being of finite dimensions
(a) penumbra
(b) resolution
(c) unsharpness (d)
none of these
46. Indication and recording is the title of ATA
(a) 30
(b) 31
(c) 33
(d) 34
47. The chain should be rejected if the extension is more than
(a) 2%
(b) 4%
(c) 6%
(d) 1%
48. If air intake fire occurs before the engine picks up an ideal
ground fire extinguishes used is
(a) methyl bronze
(b) CO2
(c) BCF
(d)
both (b) & (c)
49. Fire extinguisher kept in storage should be checked for weight
once in
(a) 2 years
(b) 1 year
(c) 3 years
(d) 5
years
50. Seam welding is
(a) Pressure welding
(c) electric resistance

(b) non-pressure welding


(d) both (a) & (c)

51. In which type of welding, the electrode is non-consumable


(a) TIG
(b) MIG
(c) Electric resistance
(d) Oxyacetylene
52. Spot welding electrode should be
(a) good conductor of electricity
heat
(c) high strength & hardness

(b) good conductor of


(d) all of these

53. In leftward welding


(a) filler rod precedes torch
rod
(c) a 60 V is prepared at the end of plate

(b) torch precedes filler


(d) both (a) & (c)

54. The colour of acetylene cylinder and oxygen cylinder is


(a) maroon & black
(b) black & maroon
(c) yellow & black
(d) black & yellow
55. In _______________ projection, the projectors are
perpendicular to the plane of projection.
(a) isometric
(b) oblique
(c) orthographic
perspective

(d)

56. In third angle projection method, the top view is always above
the ___________ view.
(a) front
(b) right side
(c) left side
(d)
pop
57. In isometric projection, each of the three axes makes an angle
of _____________ with the other two.
(a) 60o
(b) 90o
(c) 180o
(d) 120o
58. A full size drawing paper is available approximately of
(a) 565 x 565mm
(b) 565 x 765mm
x 565mm
(d) none of these

(c) 765

59. The size of the title block as recommended by the B. I.S. is


(a) 185 x 65mm
(b) 18.5 x 6.5cm
(c) 184 x 6cm
(d) 18.9 x 6.9cm
60.An assembly drawing is a description of an object made up of
___________
(a) two parts only
(b) two or more parts
(c) four parts
only
(d) none of these
61. What is the primary purpose is to show the assembly drawing?
(a) Relationship of the various parts
(b) Clear picture of
different parts
(c) clear view of single part
(d) None of these

62. Caulking tool is in the shape of a _________________ chisel.


a) blue
(b) flat
(c) blunt
(d)
cape
63. Caulking and fullering processes are generally performed with
the aid of _____________
(a) hydraulic power
(b) air pressure
(c) pneumatic power
(d) none of these
64. Thickness of fullering tool is about the
(a) as that of the plates
plates
(c) same as that of the plates

(b) less as that of the


(d) none of these

65. The diameter of the drilled hole in riveting should be


(a) about 1mm to 1.5mm
(b) about 0.1mm to
1mm
(c) about 0.5mm to 1.5mm
(d) none of these
66. What happens due to drilling during riveted joints?
(a) burr
(b) shrinkage
(c) stress concentration
(d) bending
67. Burr defect is removed by a little ________________ in riveted
joint.
(a) counter sinking
(b) counter hammering
(c) counting
burr
(d) none of these
68. Choose the correct statement.
(a)
Tearing of the plate between the rivet head if they are very
near each other.
(b) Tearing of the plate between the centre of the plate and the
rivet hole, if the hole is to the edge.
(c) Shrinking of the rivet if the diameter of the rivet is smaller than
necessary.
(d) Crushing of the plate or the rivet.
69. If the thickness of sheet is t, then what will be the empirical
formulae of the diameter of rivet, if the diameter of rivet is d
(a) d = 3t
(b) d = 3t
(c) d = 6t
(d) d
= 6t
70. The key which is in the form of a segment of a circular disc of
uniform thickness is

(a) woodruff key


(d) circular key

(b) cone key

(c) feather key

71. (A) Rivet smaller than 3/32 diameter are never used on stressed
structure.
(B) Never replace 2024T rivet with 2117rivet.
(a) both are correct.
(b) both are incorrect
(c) only (A) is correct
(d) only (B) is correct
72. Regarding permanent ballast
(a) lead bar or plate is used
placarded
(c) bolted as near as possible to CG
73. Transverse pitch is
(a) twice the rivet diameter
(c) 75% of rivet pitch

(b) painted red and


(d) both (a) & (b)
(b) 70% of rivet pitch
(d) 6-8 diameter

74. Rivet pitch is


(a) distance between center of rivet in a row(b) distance between
edge to center of rivet
(c) four times the rivet diameter
(d) both (a) & (c) are
correct
75. Edge distance (minimum) is
(a) 4D
(b) 2D
the above

(c) 6-8D

(d) any of

76. The amount of rivet length used for shop head is


(a) 1 x diameter of rivet
(b) 4 x diameter of
rivet
(c) 3 x diameter of rivet
(d) all of the above
77. Which plating process provide excellent base for paint
(a) Cd-Plating
(b) Zn-Plating
(c) Granodizing
(d) all of the above
78. Which treatment give excellent base for paint
(a) CR-Plating
(b) Parkerizing
(c) Metal spraying
(d) Zn-plating
79. The process use zinc as a medium for plating
(a) Parkerizing
(b) Sheradizing (c) Galvonizing
(d) both (b) & (c)

80. The earth rotates at its own axis at a rate of


(a) 20 degrees per hour
(b) 30 degrees per
hour
(c) 15 degrees per hour
(d) 25 degrees per
hour

PAPER - II
PART XVI
ANSWER
1. A

2. B

3. C

4. D

5. A

6. B

7. A

8. C

9. D

10. B

11. C

12. D

13. C

14. B

15. C

16. C

17. B

18. D

19. A

20. B

21. B

22. C

23. A

24. C

25. A

26. D

27. A

28. C

29. C

30. B

31. A

32. C

33. A

34. C

35. C

36. D

37. B

38. B

39. C

40. A

41. D

42. B

43. C

44. B

45. A

46. B

47. A

48. B

49. B

50. D

51. A

52. D

53. A

54. A

55. C

56. A

57. D

58. B

59. A

60. B

61. A

62. C

63. C

64. C

65. A

66. A

67. A

68. D

69. A

70. A

71. C

72. D

73. C

74. D

75. B

76. A

77. C

78. B

79. D

80. C

PAPER - II
PART XVII
1. Vulcanization on rubber
a) To increase mechanical strength and tackiness
b) To reduce mechanical strength and tackiness
c) To increase the mechanical strength and reduce tackiness
d) To reduce the mechanical strength and increase tackiness
2. Which type of Synthetic rubber will be the first choice for
manufacturing of aircraft tubeless tyre
a) Butyl rubber b) Neoprene rubber
c) BUNA-N
thiokol

d)

3. Which synthetic rubber is chiefly used in aircraft hot air duct as


sealing ring and wire insulation
a) Silicon rubber b) Polymethane rubber c) BUNA-S
d) BUNA-N
4. Highest resistance to deterioration but lowest physical property
is the characteristic of which kind of synthetic rubber.
a) GR I
b) GR S
c) GR P
d) GR A
5. To valcanise thiokol rubber, which element to be added
a) Sulfur
b) Sulfur oxide
c) Zinc
d) Zinc oxide
6. Which material is used for manufacturing of hydraulic booster piston
seal
a) Styrene butadiene seal
b) Nitrile rubber
c) Flexon rubber
d) Fluoro carbon rubber
7. Natural rubber attains fibrous structure when
a) It under goes at low temperature
b) It is frozen
0
c) It is heated to 130 C
d) It undergoes continues stress at
normal temperature
8. The grade of Kevlar fiber is used for aircraft structure
a) Kevlar 49
b) Kevlar 149
c) Kevlar 29
d) Kevlar 129
9. The composition for E glass is
a) Magnesia-alumina-silicate glass
borosilicate glass

b) Lime-alumina

c) Soda borosilicate glass

d) None of the above

10. Truly outstanding properties of strength competes with stronger


steel is kind of fiber
a) S glass
b) Hollow fibre glass
c) A glass
d) Carbon glass
11. Which composit material is difficult to cut or drill
a) Glass fibre
b) Aramid
c) Carbon / Graphite
d) None of above
12. Mark the wrong statement for carbon / graphite fibre
a) Is used to fabricate primary structure
b) It has high strength
and high rigidity
c) It takes compressive load
d) It is ductile in nature
13. The most commonly used driving tool by a mechanic is
a) Ball peen hammer
b) Cross peen hammer
c) Claw hammer
d) Sledge hammer
14. (i) Body hammers are used for driving stakes into the ground
(ii) Sledge hammers are used for smoothing or stretching the metal
a) Only (i) is correct
b) Only (ii) is correct
c) Both (i) and (ii) are correct
d) Neither (i) nor (ii) is correct
15. i) Mallets can be termed as soft hammers
ii) Plastic mallets are more useful than raw hide mallets
a) Only (i) is correct
b) Only (ii) is correct
c) Both (i) and (ii) are correct
d) Neither (i) nor
(ii) is correct
16. (i) Claw hammers are basically used for driving and pulling out
nails
(ii) The wedge of a cross peen hammer is parallel to the handle
a) Only (i) is correct
b) Only (ii) is correct
c) Both (i) and (ii) are correct
d) Neither (i) nor
(ii) is correct

17. A punch is used to


a) Mark a location
rivet
c) Locate a drill properly

b) Remove a damaged
d) All are correct

18. i) A pin punch is used to remove the shank of the rivet from the
hole after rivet head has been chiselled off
ii) Diameter of pin punch should be 1/64 inch smaller than the
diameter of the rivet to be removed
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
19. i) Location given by a prick punch should always be punched later
with a centre punch.
ii) Goggles must be used while using any type of punch.
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
20. i) A mushroom head on a punch is better than a crown head since
chances of hammer slip are reduced
ii) A centre punch can be used for a variety of punching applications
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
21. Most commonly used slip joint plier has a length of
a) 4 inches
b) 6 inches
c) 10 inches
d) 12 inches
22. Duckbill plier
a) Is a flat nose plier
safety wires
c) Have serrations on their jaws
23. Needle nose pliers are used for
a) Extracting thin/sharp components
nails
c) Gripping small electronic components

b) Is used for twisting


d) All are correct
b) Extracting
d) All are correct

24. i) A chisel can never cut the material all by itself


ii) A die is a cutting tool
a) Only i) is correct
b) Only ii) is correct

c) Both i) and ii) are correct


correct

d) Neither i) nor ii) is

25. Cutting edge of a chisel is generally ground to an angle of


a) 30 degrees
b) 70 degrees
c) 90 degrees
d) 110 degrees
26. Regarding a cutting chisel which statement is incorrect?
a) It is made from high grade steel
b) Its cutting edge is always wider than the shank
c) Cutting edge is flat so that force is applied uniformly on the surface
d) Chisel body is either square or octagonal
27. i) A cape chisel is the proper tool to use for knocking the head off
a rivet after it has been drilled through
ii) A cape chisel is forged from the same type of tool steel as the cold
chisel
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
28. Aviation snip
a) Is same as Dutchman snip
edges
c) Can easily cut thick sheet metals

b) Has serrated cutting


d) All are correct

29. Files are classified with regard to


a) Physical shape
c) Type of cut

b) Length
d) All are correct

30. Various types of cut of a file are


a) Single cut
c) Rasp

b) Smooth cut
d) Both a) & b) are correct

31. Vixen file have


a) Curved teeth
thickness
c) A special file holder

b) No taper either in width or


d) All are correct

32. i) Wood rasp files have individual teeth cut on to their surfaces
ii) Wood rasps are used to remove wood from a surface where it is not
practical to use a saw or a plane
a) Only i) is correct
b) Only ii) is correct

c) Both i) and ii) are correct


correct

d) Neither i) nor ii) is

33. i) Mill files have uniform thickness, but are tapered in width
ii) Hand files have uniform thickness and width
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
34. i) Half round files are tapered in both thickness and width
ii) Knife files are tapered in thickness as well as in width
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
35. For filing acute angles, one should use
a) Knife files
b) Round files
d) All are correct

c) Triangular files

36. Most files used in aviation have a length of


a) 4-10 inches
b) 6-12 inches
c) 6-16 inches
d) 10-20 inches
37. The part of a file that fits into the handle is called
a) Heel
b) Fitting end
c) Tang
d) Point
38. i) File is basically a chisel but with many cutting edges
ii) Triangular files are used for cutting teeth of handsaws
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
39. Double cut files have rows of teeth. These teeth are set at
a) 45 degrees and 70-80 degrees
b) 45 degrees and 45
degrees
c) 70-80 degrees and 70-80 degrees
d) None of these
40. There are five cuts of files ranging from coarsest to the finest.
Find out the wrong one
a) Coarse
b) Bastard
c) Smooth
d) Finest
41. File should be kept clean by
a) Tapping it against the bench
wire brush

b) Brushing it with a

c) Lubricating it occasionally
correct

d) Both a) & b) are

42. Which type of file has only three grades: regular, fine and smooth
a) Vixen
b) Wood rasp
c) Knife
d)
Triangular
43. Characteristics of steel are controlled by
a) Removal of carbon from iron
elements added to it
c) Amount of alloying elements added to it

b) Types of alloying
d) All are correct

44. Bearing strength of a material refers to


a) Direct tensile load it can bear
b) Resistance to tear at the point of applied load
c) Resistance to fracture at the point of applied load
d) Resistance to shear
45. Characteristics of metals relating to drawing it into wire is
a) Tensile strength
b) Malleability
c) Ductility
d) Brittleness
46. Fusibility of a metal refer to its property that permits
a) Welding
b) Drawing into thin sheets
c) Drawing into wires
d) Good thermal
conductivity
47. Aluminium alloy 1100 implies
a) Pure aluminium
copper
c) It contains 111% zinc
48. Before jacking an aircraft
a) Empty the fuel tanks
c) Level aircraft laterally
equipment

b) It contains 11%
d) Heat treated alloy
b) Fit critical stress panels
d) Remove all optional

49. It is generally necessary to jack an aircraft for weighing. Why?


a) To set the weighing scales to zero
b) To stabilize the weighing scales
c) For first determining its empty weight
d) For making aircraft level
50. (i) In cross filing, the file is moved length wise across the work
(ii) In draw filing, the file is moved side wise across the work

a) Only i) is correct
c) Both i) and ii) are correct
correct

b) Only ii) is correct


d) Neither i) nor ii) is

51. A handsaw used for cutting across the grains of wood is called a
a) Cross cut saw
b) Rip saw
c) Back saw
d)
Wood saw
52. A cross cut saw has
a) 4-6 teeth per inch
c) 10-15 teeth per inch

b) 6-12 teeth per inch


d) 12-18 teeth per inch

53. Find out the incorrect statement regarding back saw


a) It is used for cutting precision parts
b) It has 18-32 teeth per inch
c) It is same as hacksaw
d) Cutting teeth has very little set
54. Hacksaw blades are
a) Made from stainless steel
c) Held under tension in the frame
per inch

b) 12 inches in length
d) Having 10-14 teeth

55. i) Hacksaw blades are made of either carbon steel or high steel
molybdenum steel
ii) While using hacksaw, cutting is done only on the forward stroke.
The blade should be lifted for the return stroke
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
56. i) For a good cut on a hard material, a blade with more teeth
should be used
ii) While cutting a tube, a blade should be so chosen that at least five
teeth are there on each side of the tube as it is cut
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
57. Length of hacksaw is measured from
a) The outer edge
blades
c) Between the centre of fixing holes
are correct

b) toothed part of
d) Both a) & b)

58. Spiral anger bit for drilling holes in wood are


a) Generally 7-10 inches long
b) - one inch in
diameter
c) Used only with a bow type hand brace
d) All are correct
59. A screw driver can be used
a) For driving screws
c) As a chisel
60. Stubby screw driver has
a) A blunt edge
c) Only wooden handle

b) As a punch
d) All are correct
b) Blade length of up to 2
d) All are correct

61. Screw driver used when there is no clearance for normal screw
driver is called
a) Closed area screw driver
b) Stubby screw driver
c) Off set slot screw driver
d) Any one of the
above
62. Air driven power screw driver should be used
a) For large diameter screw
b) For removing screw that are jammed
c) Where large number of screws are to be removed and fitted back
d) When removing screws from harder material
63. A slot screw driver should have sufficient size of the blade to cover
certain width of the screw slot. It should cover at least
a) 50%
b) 60%
c) 75%
d) 90%
64. i) Cross point screw driver causes less damage than straight edge
screw driver
ii) Phillips screwdriver require less efforts as compared to normal
screw driver
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
65. With regard to wrenches, find out the incorrect statement
a) These are made from chrome vanadium steel
b) These are generally die cast
c) Wrenches are made in various shapes & sizes
d) These are plated to improve their appearance

66. Open end wrenches


a) Ends are inclined so as to allow the wrench to turn the nut even in
restricted space
b) Are available in British & Metric sizes
c) Open a nut faster than box end wrenches
d) All are correct
67. Box end wrenches are used
a) To loosen nuts that are exceptionally light
b) Where there is restricted space
c) For nuts that are bigger than one inch size
d) When open end wrench is not available
68. Combination wrenches means, its two ends have
a) Open and box end
b) Open and cut box
end
c) Open and flare nut end
d) All are correct
69. i) Loosing or tightening of a nut takes longer time if box end
wrench is used
ii) Box end wrenches can easily open a very tight nut because it grips
the nut at many places compared to an open ended wrench
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
70. i) A flare nut wrench is a special type of box end wrench
ii) Flare nut wrench is used basically for opening and fitting of pipelines
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
71. Spanners are classified by
a) Type
c) Size of the bolt/nut on which it fits

b) Material
d) All are correct

72. Set spanners are off set to an angle


a) So that it can be used in restricted places
b) A new grip can be got by turning the spanner over
c) For proper grip
d) Both a) & b) are correct
73. Ratchets
a) Allow removal of nut with very small amount of handle movement

b) Are available with long and short handles


c) Can easily fit into sockets
d) All are correct
74. Crowfoot socket wrench is used where the following cannot be
used
a) Open end wrench
b) Box end wrench
c) Standard socket wrench
d) All are correct
75. Monel metal is an alloy of
a) Nickel & copper
c) Copper & chromium

b) Nickel & chromium


d) Copper, nickel & chromium

76. i) Gun metal is used for gears & bearings.


ii) Brass is used for cartridge cases
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
77. Angular momentum is
a) Moment of inertia
b) Angular velocity
b)
d) Sum of a) & b)

c) Product of a) &

78. Mark the incorrect statement


a) Precession is inversely proportional to the strength & direction of
applied force.
b) Precession is inversely proportional to the moment of inertia of the
rotor.
c) Precession is inversely proportional to the angular velocity of the
rotor.
d) None of the above
79. Control of drift, relating to horizontal gyroscopes can be achieved
by:
a) Calculating corrections using earth rate formula and applying them
as appropriate
b) Applying fixed torques & cause gyro to process at a rate equal &
opposite to the earth rate.
c) As in b) but which can be varied according to latitude
d) All of these
80. When gimbal orientation is such that the spin axis becomes
coincident with one or the other of the axes of freedom which serves
as attitude displacement reference is termed as
a) Gimbal lock
b) Gimbal Error
c) Apparent drift

PAPER - II
PART XVII

ANSWER:
1. C

2. A

3. A

4. C

5. D

6. B

7. B

8. A

9. B

10. D

11. B

12. D

13. A

14. B

15. C

16. A

17. D

18. A

19. C

20. D

21. B

22. D

23. C

24. C

25. B

26. C

27. C

28. D

29. D

30. A

31. D

32. C

33. A

34. D

35. A

36. C

37. C

38. C

39. A

40. D

41. D

42. A

43. D

44. B

45. C

46. A

47. A

48. B

49. B

50. C

51. A

52. B

53. C

54. C

55. C

56. A

57. C

58. D

59. A

60. B

61. C

62. C

63. C

64. D

65. B

66. D

67. A

68. D

69. C

70. C

71. D

72. D

73. D

74. D

75. A

76. C

77. C

78. A

79. D

80. A

PAPER - II
PART XVIII
1. Corrosion control techniques are employed when corbon fibre is in
contact to aluminium
a) A layer of fiber glass is used as a barrie
b) Aluminium is anodized, primed and painted prior to assembly
c) Both (a) and (b) will be applied together
d) None of the above
2. Which composite material is useful for making aircraft parts that are
subject to high stress and vibration
a) Fibergalss
b) Aramid
c) Carbon / Graphite
d) None of these
3. Mark the correct statement
a) Carbon fiber are electrically non conductive
b) Carbon fibers have high thermal expansion
c) Carbon fibers have high fatigue resistance
4. Boron fibers are made by sintering the boron elements on a thin
film of material
a) Titanium
b) Tin
c) Tungsten
d) All
above
5. Which fiber material bears all tension, compression and bending
stresses
a) Ceramic fiber
b) Boron fiber
c) Fiber glass
d) Graphite fiber
6. Mark the correct statement in Fiber Orientation
a) Warp direction is designated at 900
b) Weft is designated at 00
c) Bias is at 450 angle of fill threads
d) None of the above
7. For repairing of fabric, which weave to be used
a) Plain weave
b) Basket weave c) Satin weave
d) All of these

8. Find out the wrong answer: Hybrids of composite material used in


Aviation field are
a) Kevlar with carbon / graphite
b) Kevlar with fiber
glass
c) Carbon / graphite with fiber glass
d) None of these
9. In fiber science, which acts as a curing agent
a) Resin
b) Matrix
c) Catalyst
these
10. Plexiglass is
a) Thermoplastic
b) Thermoset
d) None of these

d) All of

c) Laminated

11. Mark the correct answer:


Apart from strongest adhesive characteristics of epoxy resin, it has
other advantages
a) Useful at very high temperature
b) It withstand bending
stress
c) Reasonable rigidity and flexibility
d) All of these
12. Mark the correct answer:
The advantages of fillers to add to resins are
a) To control viscosity and weight
and strength
c) Both (a) and (b)
13. Nomex is a
a) Filler material
b) Matrix
d) Core material

b) To increase pot life


d) None of these

c) Reinforced fiber

14. Tapered roller bearing support


a) Radial load
b) Thrust load
Both (a) and (b)

c)

15. Bearing used on high powered aircraft engine is


a) Ball bearing
b) Roller bearing c) Plain bearing
Both (a) and (c)

d)

16. Plain bearings are used for


a) Connecting rods
b) Crank shaft
d) All of these

c) Cam shaft

17. Bearings are used to take


a) Thrust load
b) Radial load
d) Both (a) and (b)

c) Side load

18. Bearing used wher e high compressive pressure, is generally made


of
a) Babitt
b) Bronze
c) Siliver bronze d) All of
these
19. Bearing which offer more friction is made of
a) Bronze
b) Babitt
c) Silicon
these

d) None of

20. The amount of electricity a capacitor can store is directly


proportional to
a) Distance between the plate and inversely proportional to the plate
area
b) Plate area and is not affected by the distance between the plate.
c) Plate area and inversely proportional to the distance between the
plate
d) None of these
21. The correct way to connect a test volt meter in a circuit is
a) In series with a unit
b) Between the source
voltage and the load
c) In parallel with unit
d) Both (a) and (c) are
correct
22. Typical application of Zener diode is as
a) Full wave rectifiers
c) Voltage regulator

b) Half wave rectifier


d) Amplifier

23. The method used to rapidly charge a Nickel Cadmium battery


utilizes
a) Constant current and constant voltage
b) constant current and
varying voltage
c) Constant voltage and varying current
d) Varying voltage and
varying current
24. High carbon steel is generally used for
a) Shock absorbers
c) Engine mounting bolts

b) Landing gear struts


d) Springs & files

25. What material is used in the construction of firewall of aircraft


engines?
a) Aluminium alloy
b) Stainless steel
c) Chrome-molybdenum steel
d) Tungsten steel
26. Which of the statement is correct?
a) Both heat treatable & non heat treatable aluminium alloys can be
strain hardened
b) Strain hardening is same as cold working
c) Strength & hardness increases during cold working
d) All are correct
27. Find out the wrong statement regarding titanium
a) It is highly corrosion resistant
b) It maintain strength
at elevated temperatures
c) It has good resistance to creep
d) It is magnetic
28. The balls used for ball bearings are made of
a) Cast iron
b) Cast steel
c) Wrought iron
Carbon chrome steel
29. Files used in fitting shop are made from
a) Cast iron
b) High carbon steel
d) Mild steel

d)

c) Chrome steel

30. Property of a material to be drawn plastically before breaking is


called ductility. Most ductile material is
a) Copper
b) Gold
c) Lead
d) Tin
31. i) Aluminium has high electrical and thermal conductivity
ii) Ductility of aluminium improves with the addition of iron & silver
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
32. i) Muntz metal is same as yellow brass
ii) Muntz metal contains copper & zinc in the ratio of 3:2
a) Only i) is correct
b) Only ii) is correct
c) Both i) and ii) are correct
d) Neither i) nor ii) is
correct
33. Potential difference between two conductors insulated from each
other is measured in
a) Ampere
b) Coulomb
c) Ohm
d) Volt

34. Correct way to connect a test voltmeter in a circuit is


a) In series with a unit
b) In parallel with a
unit
c) Between source voltage and load
d) Both b) & c) are
correct
35. Which term means .001 ampere
a) Micro ampere
b) Milli ampere
c) Kilo ampere
d) Nano ampere
36. Unit used to express electrical power is
a) Ampere
b) Volt
c) Watt
d) Coulomb
37. Transfer of electrical energy from one conductor to another without
the aid of electrical connection is
a) Induction
b) Air gap transfer
c) Not possible
d) Possible but will cause excessive
arcing thus not practical
38. Magnetic lines of force pass most readily through
a) Aluminium
b) Copper
c) Iron
d) Titanium
39. In a straight conductor, the resistance is not affected by
a) Length
b) Temperature
c) Shape of cross section
d) Material
40. Pitot pressure varies with
a) Speed

b) Air density
d) None of these

c) Speed and Air density

41. Altimeter and rate of climb indicator utilize


a) Static pressure b) Pitot pressure
c) Either a) or b)
d) Both a) and b)
42. Pitot static system have heating elements to
a) Remove moisture from the air
b) Prevent ice
formation
c) To permit flying at high altitude
d) All are correct
43. Pressure heads of pitot static system should not be painted,
because it
a) Impairs their thermal efficiency

b) May cause obstruction of orifices


c) None of the above
d) Both a) and b) are correct
44. Leak test of pitot static system should be carried out
a) After installation of a component / instrument
b) Whenever malfunctioning is suspected
c) At specified periods indicated in servicing schedules
d) All are correct
45. Which instruments are connected to the aircraft pitot static
system?
a) Vertical speed indicator
b) Altimeter
c) Airspeed indicator
d) All are correct
46. The instrument that measures difference between pitot & static
pressure is
a) Altimeter
b) Pressure gauge
c) Airspeed indicator
d) Vertical speed indicator
47. The unit where calculations are processed is called
a) Central processing unit (CPU)
b) Control unit
c) Arithmetic and logic unit (ALU)
d) Computing unit
48. Sequence of steps for computing a program is known as
a) Flow chart
b) Sequence process
c) Algorithm
d) None of these
49. Basic function of a computer is
a) Addition
b) Multiplication
are correct
50. EDP stands for
a) Electrical data processing
processing
c) Entry data processing
programme

51. A computer basically


a) Processes data
instructions
c) Perform mathematical calculations

c) Division

d) All

b) Electronic data
d) Electronic discrete

b) Stores data as per given


d) All are correct

52. Computer stores instructions in


a) English language
system
c) Octal number system

b) Decimal number
d) Binary

53. In a straight and level flight of an aircraft


a) Lift equals aircraft weight
weight
c) Lift is less than weight
of aircraft and its loading

b) Lift is more than


d) Depends upon size

54. Whenever lift is generated, there is certain amount of drag


associated with it. This is called
a) Form drag
b) Skin friction drag
c) Induced drag
d) Shape drag
55. Lift generated by an airfoil is maximum at an angle of attack of
about
a) 0 degrees
b) 4 degrees
c) 12 degrees
d) Stalling value
56. Lift generated by an aircraft depends upon
a) Density, forward velocity & aircraft area
b) Density, square of forward velocity and aircraft area
c) Density, square of forward velocity and wing area
d) Density, forward velocity & wing area
57. Lift on a wing
a) Acts through centre of gravity
c) Is perpendicular to chord line
through centre of pressure

b) Acts vertically upwards


d) Acts vertically upwards

58. The Tension of brushes to provide brush pressure is approx.


a) 6 Psi
b) 8 Psi
c) 10 Psi
d) 12 Psi
59. A four pole generator will have
a) 2 interpole
b) 4 interpole
d) 8 interpole

c) 6 interpole

60. In a 3 phase system, the phase winding is spaced symmetrically so


that the voltage induced is
a) 90o apart
b) 120o apart
c) 60o apart
d) 180o apart

61. To avoid armature reaction of small DC generator (1000 watt or


less) type. The method
used is
a) Interpole Method
b) Brush setting method
c) both (a) & (b)
d) None of these
62. Compensating winding is used in series with interpole winding to
a) Increase he life of brushes
b) Distortion of field
c) Reduces radio interference
d) All the above
63. Staggering slots are used in armature of a DC generator to
a) Minimise ripple voltage
b) Maintain constant
output
c) Minimise eddy Current loss
d) None of these above
64. A 3 four pole alternator, running at 6000 rpm will have frequency
of
a) 100 c/s
b) 200 c/s
c) 300 c/s
d) 400 c/s
65. While installing battery (Ni-Cad) on a/c you must inspect
a) Ventilation system of a/c
b) Cable for chaffing
c) Quick disconnection mechanism
d) All of these
66. What will be value of resistance of yellow, red, orange and gold
a) 42000 10%
b) 42000 5% c) 12000 5% d) 22000
10%
67. AC generator works on the principle of
a) Faradays law of electro-magnetic induction b) Mutual induction
c) Self induction
d) All of these
68. Flight calculations are based on the magnitude and direction of
a) Lift & drag
b) Weight & thrust
c) Lift &
thrust
d) Both a) & b)
69. The factors limiting the aspect ratio are
a) Structural consideration
c) Lift consideration

b) Drag consideration
d) Both a) & b)

70. What is required to reduce the landing speed?


a) A low minimum drag coefficient
b) A small movement
of C of P
c) A high max CL
d) A high value of CL3/2/CD

71. With increase in altitude pressure & temperature


a) Drops
b) Will rise
c) Pressure drops, temperature increases
d) Temperature drops,
pressure increases
72. The disadvantage of vacuum operated Gyro is
a) At high altitude, stability is reduced due to decrease in atmospheric
pressure.
b) Weight due to pipelines
c) Possibility of contamination by corrosion and dirt particles.
d) All of these
73. Gyro of AC operated instruments utilize the principle of squirrel
cage induction motor and because of high frequency of power supply,
greater rotor speeds are possible of approximate.
a) 23000rpm
b) 24000rpm
c)
24500rpm
d) None
74. Indication of pitch & Bank attitude are presented by the relative
position of
a) Aircraft symbol
b) Gyro stabilised bar
(Horizon symbol)
c) Both a) & b)
d) None of these
75. Freedom of gimbal system movement about the roll & pitch axes in
gyro horizon is ______ respectively
a) 3600 and 900
b) 3600 and 800
c) 3600 and 850
d) None
76. The reason for restricting pitch movement of gyro horizon is to
prevent
a) Gimbal error
b) Gimbal lock
c) Transport wander
d) None
77. Izod test measures
a) Toughness
c) Energy in breaking

b) Height of upswing
d) Hardness

78. Fatigue test is for determining


a) Stress in material
c) Stress limit for material

b) Strain in rod
d) Elongation of wire

79. Torsion test is essential for


a) Wires
b) Tube
Sheet
80. Bending test indicates
a) Ductility
b) Brittleness
d) Density

c) Rods

c) Hardness

d)

PAPER - II
PART XVIII
ANSWER:1. C

2. B

3. C

4. C

5. B

6. D

7. C

8. D

9. C

10. A

11. D

12. C

13. C

14. C

15. B

16. D

17. D

18. B

19. A

20. C

21. C

22. C

23. C

24. D

25. B

26. D

27. D

28. D

29. B

30. B

31. A

32. C

33. D

34. B

35. B

36. C

37. A

38. C

39. C

40. C

41. A

42. B

43. D

44. D

45. D

46. C

47. C

48. C

49. A

50. B

51. D

52. D

53. A

54. C

55. D

56. C

57. D

58. A

59. B

60. B

61. C

62. D

63. A

64. B

65. D

66. B

67. A

68. D

69. D

70. C

71. A

72. D

73. B

74. C

75. C

76. B

77. B

78. C

79. A

80. A

PAPER - II

PART XIX
1. S in Al-alloy designation indicates
a) Cast alloy
b) Wrought alloy
c) As in b) and used for a/c structure
d) None
2. Which Al-alloy is more corrosion resistant?
a) 2 S
b) 3 S
c) 17 S
d) 52 S
3. Al clad is generally of
a) 17 S & 24 S
b) 24 S & 52 S
c) 52 S & 53 S
d) 53 S & 62 S
4. Inter
a)
b)
c)
d)

crystalline corrosion is generally occurred in


Al-alloy containing copper composition
17 S
24 S
All of above

5. Which of the following material is used for spot welding


a) Clad alloys
b) 52 S Al-alloy
c) Both a and b
d) None
6. Natural rubber is a polymer of
a) Isoprene
b) Neoprene
c) Diprene
d) None

7. Which material is used for increasing the hardness of natural


rubber?
a) Sulpher
b) Phosphorus

c) Sodium
d) Carbon
8. Which is the basic colour of commercial BUNA-S
a) White
b) Black
c) Red
d) Green
9. GR-A is a known as BUNA-N, in which A stands for
a) Butadiene
b) Acrylonitrile
c) Monovinyl
d) Nitrile
10. Neoprene is designated as GR-M, in which M is stands
a) Monovinyl
b) Chloroprene
c) Acrylonitrile
d) Styrene
11. Out of the following memory types, one that is volatile
a) Magnetic Disk
b) Ferrite Core
c) Semi Conductor ROM
d) Semi Conductor RAM
12. A 4-bit date word is called
a) Data bus
b) Band
c) Byte
d) Nibble
13. The heart of digital computer is
a) I/O
b) Processor
c) CPU
d) None of the above

14. Semi conductor memories are


a) Volatile
b) Non-Volatile
c) Volatile as well as Non-Volatile

d) Neither Volatile nor Non-Volatile


15. The decimal number 422 is equal to which of the following
hexadecimal number
a) 6A
b) A6
c) 6A1
d) 1A6
16. The decimal equivalent of 101.101 is
a) 5.625
b) 7.625
c) 45
d) 47
17. High speed semi conductor memory, which is used as additional
memory device
a) ROM
b) PROM
c) Cache memory
d) None of these
18. From the point of view of integration, a microprocessor chip
employs
a) S.S.I (Small Scale Integration)
b) M.S.I (Medium Scale Integration)
c) L.S.I (Large Scale Integration)
d) G.S.I (Grand Scale Integration)
19. Floppy disk is a
a) Flexible storage
b) Permanent storage
c) ROM
d) Fast storage
20. MODEM is a
a) Code changing system
b) Programme conversion system
c) Modulator Demodulator system
d) Demodulator modulator system
21. Power factor is the ratio of
a) True power / apparent power
b) Apparent power / true power
c) Zero power / true power
d) None of the above

22. Transformer works on the principle of


a) Self induction
b) Mutual induction
c) Electromagnetic induction
d) Magnetic induction
23. The factor, which determines whether a given transformer is
stepped up or steeped down, is given by
a) Current ratio
b) Voltage ratio
c) Power ratio
d) Turns ratio
24. The
a)
b)
c)
d)

purpose of iron core in transformer is


Given electrical energy from the source
Isolates primary with secondary
Join primary with secondary
Provides low reluctance for magnetic lines of force

25. If the ratio of the transformer input voltage to the output voltage
is same as the turn ratio then, transformer is said to be
a) 50% efficient
b) 110% efficient
c) 100% efficient
d) 25% efficient
26. Which of the following transformer can approach 100% efficient
a) Iron core transformer
b) Ferrite core transformer
c) Copper core transformer
d) None of these
27. The
a)
b)
c)
d)

range of frequency in the case of audio transformer is


40 to 20000 c.p.s
20 to 20000 c.p.s
100 to 10000 c.p.s
10 to 10000 c.p.s

28. RF transformer utilizes


a) Iron core
b) Copper core
c) Magnetic core

d) Air core
29. The symbol of autotransformer used for communication or
navigation circuit is

30. Copper loss in a transformer is caused by


a) Due to iron core
b) The resistance of the conductor comprising of the turns of the
coil
c) Due to no. of turns
d) None of the above
31. The fastest logic gate is
a) TTL
b) ECL
c) DTL
d) RTL
32. The Boolean expression Y of two inputs ExNOR gate is
a) Y = A . B + A B
b) Y = A . B + A B
c) Y = A . B + A B
d) Y = A . B + A B
33. To remove half cycle of AC input voltage, we can employ
a) Clamper circuit
b) Clipper circuit
c) Zener diode
d) LED
34. The self exited mixer is economical because
a) It does not require separate amplifier
b) It does not require tank circuit
c) It needs to generate f0 + fs
d) None
35. There is no carrier present in
a) DSBFC
b) SSBFC

c) DSBSC
d) USBFC
36. The ionospheres D-layer reflects
a) HF wave
b) LF wave
c) MF wave
d) a) and b)
37. Main drawback of TRF AM Receiver was
a) More complex circuit
b) Tuning to fix frequency of different stages was difficult
c) Un-economical
d) None
38. The average value of AC is given by
a) Im / 2
b) Im / 2
c) 2Im /
d) Im / 2
39. In a superhet receiver, the first most stage is
a) IF amp
b) AF amp
c) RF amp
d) Mixer
40. In a superhet receiver, the name, first detector is often given to
a) 1st RF amp
b) Local Oscillator
c) IF amp
d) Mixer
41. The trunion nut of an aircraft landing gear requires a torque of
320 inch pound. To reach the nut, a 2 straight adapter must be used
on an 18 torque wrench. How many foot-pounds will be indicated on
the torque wrench when the required torque of the nut is reached?
a) 24
b) 28.8
c) 288
d) 220
42. An o-ring intended for use in hydraulic system using MIL-H-5606
(Mineral base) fluid will be marked with
a) A blue strip or dot
b) One or more white dots

c) A white and yellow strip


d) Red strip
43. A hydraulic hose identified as MIL-H-8794 will have a yellow strip
running the length of the hose. This stripe
a) Identifies that the hose is for hydraulic fluid only Is used to
insure that the hose is installed without excessive twisting
b)
c) Identifies that the hose is constructed of synthetic rubber and
may be suitable for a wide range of operation
d) Both a) and b) are correct
44. To protect packing rings or seal from damage, when it is
necessary to install them over or inside threaded section, the
a) Threaded section should be coated with a heavy grease
b) Packing should be stretched during installation to avoid contacts
with the threads
c) Threaded section should be covered with a stiff paper sleeve
d) Packing should be lubricated
45. The minimum amount of slack that must be left when a flexible
hose is installed in an aircraft hydraulic system
a) 8%
b) 10%
c) 5%
d) 7%
46. No-12 tubing has outside diameter of
a)
b)
c) 3/8
d)
47. What kind of rigid tubing can be flared with a double flare?
a) 5052-O Al-alloy
b) 6061-T Al-alloy tubing with size from 1/8 3/8 OD
c) 7075-T
d) Both a) and b)
48. A fibre type self locking nut must never be used on an aircraft if
the bolt is
a) Under shear loading
b) Under tension loading
c) Subject to rotation

d) Both a) and b)
49. Unless otherwise specified, torque values for tightening aircraft
nuts and bolts relate to
a) Clean dry thread
b) Clean lightly oiled thread
c) Either dry or lightly oiled thread
d) None
50. Mark the correct statement
a) Double flare is more concentric and smoother than single flare
b) AN fitting has a shoulder between the end of the threads and the
flare cone
c) AN sleeve is longer than AC sleeve
d) Both a) and b)
51 Red radial line on the scale of instrument indicates
a Take off and precautionary ranges
b Normal operating ranges
c Maximum and minimum limits
d Range in which operation is prohibited
52 Red arc on scale of instrument indicates
a Take off and precautionary ranges
b Normal operating ranges
c Maximum and minimum limits
d Range in which operation is prohibited
53
a
b
c
d

Yellow arc on scale of instrument indicates


Take off and precautionary ranges
Normal operating ranges
Maximum and minimum limits
Range in which operation is prohibited

54
a
b
c
d

Qualitative display presents information in the form of


Symbolic form only
Pictorial form only
Both A and B
None of the Above

55 Spacing of marks on indicator scale is generally


a Linear only
b Non-Linear only
c Both A and B

None of the above

56
a
b
c
d

In troposphere temperature decreases at a rate of


1.98 degrees centigrade per thousand feet increase in altitude
2.98 degrees centigrade per thousand feet increase in altitude
0.98 degrees centigrade per thousand feet increase in altitude
3.98 degrees centigrade per thousand feet increase in altitude

57 Heating element fitted around the pitot tube casing is to


a Prevent ice formation
b Reduce position error
c Reduce instrument error
d Reduce density error
58 Static vents are always located one on each side of a fuselage
and inter
connected so as to balance out pressure effect resulting from
a Any yawing or side slip motion of an aircraft
b Sudden pitch up
c Sudden pitch down
d None of the above
59 Bimetallic device connected in magnification lever system of
altimeter is for
a Compensation of installation error
b Compensation of scalar error
c Compensation of temperature error
d All of the above
60
a
b
c
d

Setting knob in front of altimeter is for


Setting QNH only
Setting QFE only
Both A and B
None of the above

61. The Vernier height gage can be used as


a) Calliper
b) Depth gage
c) Surface gage
d) Snap gage
62. For measuring the diameter of small holes, which of the following
gages can be
used?
a) A small hole gage
b) Depth gage

c) Plug gage
d) Telescoping gage
63. The reading on the Vernier caliper is
a) 2.494 inches
3

10

b) 2.4769 inches
c) 2.438 inches
d) 2.394 inches
64. In a Vernier bevel protractor
a) 12 divisions on the Vernier
degree on the disk
b) 13 divisions on the Vernier
degree on the disk
c) 13 divisions on the Vernier
degree on the disk
d) 12 divisions on the Vernier
degree on the disk

15

20

scale occupy the same space as 24


scale occupy the same space as 23
scale occupy the same space as 24
scale occupy the same space as 23

65. Inside diameter of a cylinder is measured by


a) Small hole gage
b) Cylinder bore gage
c) Dial indicator
d) Inside micrometer
66.How many blocks are there in the third series of gage blocks?
a) 9
b) 19
c) 49
d) 3
67. The scriber point is usually made of
a) Stainless steel
b) Tool steel
c) Hardened & tempered cast iron
d) Hardened & tempered carbon tool steel
68. Surface plates are made of
a) Carbon steel
b) Cast iron
c) As in a or granite
d) As in b or granite

25

69. For measuring the valve clearance of a piston engine, which gage
is used?
a) Screw pitch gage
b) Fillet gage
c) Filler gage
d) Height gage
70. Universal & combination bevels are used for
a) Measuring angles within one degree
b) Measuring angles that are difficult to measure by ordinary
protractors
c) Checking & transferring angles, which are difficult to measure by
ordinary protractors.
d) Both a & b are correct

PAPER - II
PART XIX
1. c

2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
a
c
c

a
d
d
c
c
d
a
c
c
a
c
a
c
a
a
a
a
a
a
a
a
b
d
b
a
c
a
b
c
c
d
a

42.
43.
44.
45.

a
a
d
c
a
a
b
b

46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
68.
69.
70.

b
d
c
a
d
c
d
a
c
c
a
a
a
c
c
b
a
a
d
b
b
d
d
c
c

PAPER - II
PART XX
1. GR-I designated for which type of rubber
a) Neoprene
b) BUNA-S
c) BUNA-N
d) Butyl
2. Which type of properties is introduced in rubber after vulcanising
process?
a) Elasticity
b) Strong ness
c) Reduce the tackiness
d) All of the above
3. A/C rivets are identified by
a) Head Style
b) Alloy
c) Length & Diameter
d) All
4. For accurate location of particular area on an a/c, which of the
following is necessary?
a) Water line
b) Butt line
c) As in a) and b) in conjunction with station line
d) None
5. Which type of corrosion is occurred in stainless steel after electric
arc welding?
a) Pitting
b) Galvanic
c) Inter crystalline
d) Fretting
6. For spot welding, in stainless steel, which is most suitable
a) Low-voltage
b) High-amperage
c) Low-voltage and High-amperage
d) High-voltage and Low-amperage
7. Heat generated in spot welding is measured by
a) Resistance x (Current)2 x Time

b) Resistance x Time / (Current)2


c) (Current)2 / Resistance x Time
d) Resistance x Current
8. Which of the following is the Non-Magnetic?
a) Inconel
b) K-Monel
c) Monel
d) All
9. SAE 13XX represents
a) Magnesium Steel
b) Manganese Steel
c) Silicon Steel
d) Chromium Steel
10. Hot piece of metal is increased in thickness and decreased in
length
a) Upsetting
b) Down setting
c) Swaging
d) Rolling
11. Every processor must necessarily have a
a) Data bus
b) Data bus & Address bus
c) Control bus
d) Data bus, Control bus & Address bus
12. A device that works in conjunction with a computer but not as
part of it is called
a) Hardware
b) Memory
c) Microprocessor
d) Peripheral device
13. The unit of the speed of a digital I.C is
a) Hz
b) KHz
c) MHz
d) GHz
14. Which of the following storage has greatest capacity with less
cost per bit?
a) Semi conductor memory

b) Magnetic tape
c) Magnetic drum
d) None of these
15. Which of the following statement is true?
a) Compiler is the name given to the computer operator
b) Compiler is the part of the digital machine to store the
information
c) Compiler is the translator of source program to object
program
d) Compiler is the name given to the punched tape
16. Trace the value for binary addition
a) 0 with a carry of 1
b) 1 with a carry of 1
c) 1 with no carry
d) 0 with no carry

(1 + 1)

17. Which of the following memories has got equal access time for all
locations of the memory limit?
a) Read Only Memory (ROM)
b) Programmable Read Only Memory (PROM)
c) Random Access Memory (RAM)
d) Erasable ROM
18. Which of the following memories will be used to store variable
quantities or data
a) RAM
b) ROM
c) PROM
d) EPROM
19. The access time for semi conductor memories is of the order of
a) A few milliseconds
b) A few microseconds
c) A few nanoseconds
d) A few seconds
20. Semiconductor memories are faster than magnetic memories
a) True
b) False
21. To get a basic D.C. generator from A.C generator which of the
following arrangement is made
a) By replacing the slip rings of the A.C generator with
commutator

b) By the addition of extra slip rings


c) By connecting a rectifier
d) None of the above
22. The rotating part of a DC generator is called
a) Field coil
b) Yoke
c) Armature
d) None of these
23. The e.m.f generated in armatures conductor of a D.C. machine
is of nature
a) A.C
b) D.C
c) Both
d) AC and DC
24. Variations of D.C voltage generated by D.C generator is called
a) Ripple
b) R.M.S
c) Average
d) Crest
25. The ripples generated in DC generator may be reduced by
using
a) More loops or coils
b) Less loop or coils
c) Both
d) None of the above
26. There must be an ______ number of poles in any generator
a) Even
b) Odd
c) Both
d) None of the above
27. The purpose of slotting in armature is
a) To increase mechanical safety
b) To increase electrical safety
c) To increase both safety
d) None of these
28. The brushes in generator are generally made up of
a) High grade carbon

b) High grade silicon


c) High grade selenium
d) High grade zinc
29. In DC machine the commutator surface is highly polished to
a) Reduce friction
b) Reduce eddy current loss
c) Both
d) None of these
30. Which of the following DC generator(s) can never be used with
airplane?
a) Series wound D.C generator
b) Shunt wound D.C generator
c) Compound wound D.C generator
d) All of the above
31. The term 10-5 farads mean
a) 1 mili-farad
b) 10 micro-farad
c) 10 nano-farad
d) none
32. The unit of electrical power is
a) Joules
b) Watt-second
c) Joule-seconds
d) Watts
33. One angstrom (A0) is equivalent to
a) 10-9 meters
b) 10-10 meters
c) 10-9 seconds
d) 10-10 seconds
34. Which is true statement about capacitor?
a) Blocks DC
b) Allows DC
c) Blocks AC
d) None
35. For N P N transistor, arrowhead indicates the direction of
a) Minor holes current
b) Major holes current
c) Minor electron current
d) None

36. To bypass the AC components, in any device, select most


appropriate
a) Inductor is connected in series
b) Capacitor is connected in series
c) Inductor is connected in parallel
d) Capacitor is connected in parallel
37. In a P-N-P transistors, the device is ON only when
a) Base is positive with respect to emitter
b) Base is negative with respect to emitter
c) Emitter is negative with respect to base
d) None
38. In a series connection
a) Voltage is same across each element
b) Current is same in each element
c) Both are correct
d) None
39. The symbol
a) Conductor
b) Capacitor
c) Condenser
d) Variable Condenser

indicates

40. If supply voltage = 30V, then working voltage of capacitor could


be
a) 90V
b) 45V
c) 50V
d) 55V
41. The useful load of an aircraft is
a) Difference between maximum gross weight and empty weight
b) Difference between maximum net weight and total weight
c) Sum of empty weight and gross weight
d) Weight of fuel
42. MTCS
a) CD-plated rivet should not be used in areas where temperature
of 250o or more are likely to be encountered
b) If the thickness of the sheet is less, then half the diameter of the
rivet is used
c) Failure of joint will depend on the bearing stress rather than
shear stress in the rivet.
d) All of the above

43. Rivets are designed


a) Stronger in shear
b) Stronger in tension
c) Should not be subjected to excessive tension load
d) Both a) and c)
44. Zero fuel weight means
a) AUW menus weight of fuel
b) Weight of cargo, passenger and crew
c) Maximum allowable weight of loaded aircraft without fuel and
statement b)
d) All of the above
45. I-beam is produced by
a) Rolling
b) Casting
c) Forging
d) None
46. Caustic cleaning products used on Al-structure have the effect of
producing
a) Passive oxidation
b) Improved corrosion resistance
c) Corrosion
d) None
47. Fayed surface cause concern in chemical cleaning because of the
danger of
a) Forming passive oxide
b) Entrapping corrosive material
c) Corrosion by embedded iron oxide
d) All of the above
48. The rust or corrosion that occurs with most of the metal is the
result of
a) A tendency for them to return their natural state
b) Blocking the flow of electrons in homogenous metals or between
dissimilar metal
c) Electron flow in or between metal for cathode to anode area
d) All of the above
49. Which of the listed condition is not one of the requirements for
corrosion to occur

a)
b)
c)
d)

Presence of electrolyte
Electrical contact between an anodic area and a cathodic area
Presence of passive oxide film
None of these

50. Inter-granular corrosion on Al-alloy part


a) May be detected by surface pitting, white powdery deposit
b) Appears as thread like filament
c) Cannot always be detected by surface indication
d) All of the above
51.
a)
b)
c)
d)

When QNH is set on milibar scale, the altimeter reads


Altitude above mean sea level
Height above the airport elevation
Both A and B
None of the above

52.
a)
b)
c)
d)
53.
a)
b)
c)
d)

When QFE is set on milibar scale, altimeter reads


Altitude above mean sea level
Height above the airport elevation
Both A and B
None of the above
Pitot head is mounted parallel to the
Latitudinal axis of aircraft
Longitudinal axis of aircraft
Both A and B
None of the above

54. All the altimeter


a) Are constructed on the principle of Aneroid barometer
b) They have pressure responsive elements
c) Aneroid mechanism
d) All of the above
55. Hysterisis error in altimeter
a) Is induced by aircraft maintaining a given altitude for certain
period of time and suddenly making a large altitude change
b) This error will eliminate itself with slow climbs and descends
c) After maintaining a new altitude for a reasonable period of time
d) All of the above
56 Installation errors in altimeter mechanism is
a) Caused by change of alignment of static pressure port with the
relation wind
b) Speed of aircraft and angle of attack of aircraft

c) By location of the static port in a disturbed pressure field


d) All of the above
57 An ROCI is connected to
a) Static pressure only
b) Pitot pressure only
c) Both A and B
d) None of the above
58 In ROCI during dive of aircraft, the diaphragm
a) Contracts
b) Expands
c) Both a & b
d) No effect
59 Any sudden or abrupt change in the aircraft altitude may cause
erroneous
indications of ROCI
a) Due to a sudden change of airflow over static port
b) Sudden change of air flow over pitot head
c) On both A and B
d) None of the above
60 An instantaneous ROCI is
a) Recent development
b) Incorporates acceleration pumps
c) Eliminates limitations associated with calibrated leak assembly
d) All of the above
61. Which type of pipe wrench is designed with adjustable serrated
jaws for gripping round pipes?
a) Warnok type
b) Stillson type
c) Super wrench tool
d) Williams type
62. Vise grip pliers is also known as
a) Heavy pliers
b) Lever jaw wrench
c) Monkey pliers
d) None
63. Punch holders are used to hold
a) Punches
b) Chisels

c) Both a & b are correct


d) As in a, when a hard blow is required
64. Which pliers can be used for completing the safety wire operation?
a) Safety wire pliers
b) Diagonals & duck bill pliers
c) Both a & b are correct
d) As in a & diagonals
65. Diagonals are used for
a) Cutting steel wires & rods
b) Cutting bolt heads
c) Both a & b are correct
d) None
66. The shape of long nose pliers is
a) Round
b) Half- round
c) Square
d) None
67. The jaws of vise grip pliers is released from locking by
a) A small lever at each handle
b) A compound lever at both handles
c) A small lever at one of the handles
d) None

68. What action locks the jaws of a vise grip pliers?


a) Compound leverage action
b) Lever action
c) Toggle action
d) None
69. Which thread is used where a great strength is required in one
direction?
a) Acme
b) Square
c) Worm
d) Buttress
70. In interlocking- joint pliers,
a) There are a number of holes at the hinge point

b) There are two holes at the hinge point


c) There are several curved grooves at the hinge point
d) None

PAPER - II
PART XX
1. d
2. d
3. d
4. c
5. c
6. c
7. a
8. b
9. b
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.

a
d
d
a
a
c
a
c
a
c
a
a
a
a
a
a
a
a
a
a
a
b
d
b
a
a
a
b
b
d

40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
68.
69.
70.

b
a
d
d
c
a
c
b
a
c
c
a
b
b
d
d
d
a
b
a
d
b
b
c
c
d
b
c
c
d
c

PAPER - II
PART XXI
1) Which of the following have greatest tensile strength
a) Fibreglass
b) Aramid
c) Carbon
d) Ceramic
2) Which vector of fibres science takes shear load
a) 45o
b) 90o
c) 60o
d) 30o
3) Maximum strength of fibres is in which direction of bi-directional
fabric
a) Warp
b) Weft
c) Biased
d) Fill
4) Which of the following is the unidirectional fabric styles
a) Mats
b) Tapes
c) Kevlar
d) Fibreglass
5) Output power of piston engine is depend upon
a) Intensity of spark produced by spark plug
b) Heat energy applied on piston head
c) Mean effective pressure during power stroke
d) Moisture available in ambient air
6) Stab trim control used for
a) Change the angle of incident of horizontal stabilizer
b) Change the longitudinal dihedral
c) Movement of control surfaces fitted at empennage
d) All of the above
7) In steel casting, porosity can detect more easily by
a) Dye penetrant method
b) Magnetic particle inspection

c) Eddy current
d) X-Ray
8) Rate of staining is an indication of
a) Volume of defect
b) Width of defect
c) Depth of defect
d) Both b and c
9) Which of the following can use as leak tester
a) Ultrasound method (Water immersion method)
b) Dye-penetrant method
c) Magnetic particle inspection
d) None of these
10)
as
a)
b)
c)
d)

Elliptical motion of wave on the upper surface of material known


Shear wave
Compression wave
Surface wave
Tension wave

11) The memory unit that communicates directly with the CPU is called
a) Main memory
b) Auxiliary memory
c) Cache memory
d) EPROM
12) The flow chart is a
a) Systematic representation of a task
b) Systematic representation with logical decision
c) Systematic pictorial representation with logical decision
d) Random representation of a task
13) The most powerful computer is
a) Micro computer
b) Super computer
c) Mini computer
d) Lap top computer
14) Excess speed of computer depends upon
a) Software used
b) Frequency and signal received

c) Both Software and Hardware


d) Only Hardware

15) Which are related to the memory


1. Hard disk
2. Key board
Monitor
a) 1 & 2
b) 2 & 3
c) 1 & 3
d) 2 & 4
16) Expand the term RAM
a) Random Access Memory
b) Reverse Access Memory
c) Random Access Monitor
d) Reverse Access Monitor
17) Which language is the oriented language?
a) PASCAL
b) BASIC
c) FORTRAN
d) COBOL
18) In third generation computer
a) Integrated circuits are used
b) Microprocessor is used
c) Transistors are used
d) None of the above
19) The unit of Memory is
a) Bytes
b) Mega bite
c) Mill
d) Byles
20) Analog computer is
a) More correct than digital computer
b) Less accurate than digital computer
c) Equal with digital computer
d) None of these

3. CD ROM

4.

21) Which of the following DC generator has very poor voltage


regulation
a) Series wound D.C generator
b) Shunt would D.C generator
c) Differential compound D.C generator
d) Cumulative compound D.C generator

22) Series wound D.C generator cannot be used in airplane because


a) They have very poor voltage regulation
b) Poor efficiency
c) Large losses
d) None of these
23) The output voltage of a series wound D.C generator may be
controlled by
a) Using a rheostat in parallel with the field windings
b) Using a rheostat in series with the field windings
c) Both a and b
d) None of the above
24) If a constant voltage is desired, which one of the D.C generator we
would prefer
a) Series wound D.C generator
b) Shunt wound D.C generator
c) Both a and b
d) None of these
25) In a compound wound generator the magneto motive force is
equal to the
a) Sum of series and shunt field component
b) Multiplication of series and shunt field component
c) Square of series and shunt field component
d) Square root of series and shunt field component
26) A generator in which the no load and full load voltages have the
same value is called
a) Flat compound generator
b) Shunt generator
c) Series generator
d) Both b and c

27) Compound generators are usually designed to be


a) Over compounded
b) Under compounded
c) Flat compounded
d) All of these
28) In a situation where voltage regulation is of prime importance we
prefer to use
a) Compound generator
b) Series generator
c) Shunt generator
d) All of these

29) Differential generators are


a) Constant current generator
b) Constant voltage generator
c) Constant power generator
d) None of these
30) The main application of differential generator is
a) Electric arc welding
b) Fans
c) Turbines
d) All of these
31) One nibble is equal to
a) 8 bits
b) 4 bytes
c) 8 bytes
d) 4 bits
32) Binary equivalent of (29)10 is
a) 11101
b) 10101
c) 10011
d) 11111
33) Decimal equivalent of (10111011101) 2 is
a) 1500

b) 1401
c) 1501
d) 1600
34) Binary equivalent of (91.75)10 is
a) 010110.11
b) 1110011.11
c) 1011011.11
d) 1011010.1
35) Binary addition of (11011+111+11)2
a) 100101
b) 110101
c) 010101
d) 101101

36) The Boolean expression for output


B
Y
C
a) Y=(A.B).C
b) Y=A.B.C
c) Y=(A.B).C
d) Y=A.(B.C)

37) How many bits are there in 1KB?


a) 1000 bits
b) 1024 bits
c) 2048 bits
d) 108 bits
38) Immediately after picking up of signal by a super het type
receiving antenna, the signal goes to
a) RF stage
b) Detector stage
c) IF stage
d) AF stage
39) The unit of magnetic flux is
a) wb/m2

b) Mili Henry
c) wb
d) Farads
40) In line of sight communication, we use
a) UHF wave
b) VHF wave
c) VLF wave
d) HF wave
41) What may be used to remove corrosion from highly stressed steel
part
a) Steel wire brush
b) Fine grit Al-oxide
c) Medium grade carborendum paper
d) All of the above
42) Galvanic action caused by dissimilar metal contact may best be
prevented by
a) Placing a nonporous dielectric material between the surface
b) Cleaning both surface with a non residual solvent
c) Apply paper tape between the surface
d) None of these
43) Corrosion caused by galvanic action is the result of
a) Excessive anodization
b) Contact between two unlike metals
c) Excessive etching
d) All of the above
44) Which of the following is most anodic
a) Cadmium
b) Magnesium
c) Zinc
d) 7075-T6
45) Which is most cathodic
a) Zinc
b) Stainless steel
c) Chromium
d) Al-alloy
46) Galvanic corrosion is likely to be most rapid and severe when

a) The surface area of cathode is smaller than anode


b) The surface area of anodic material is smaller than cathodic
material
c) Approximately same
d) All are correct
e) Magnesium
e) Chromium
The surface area of anodic material is smaller than cathodic
aterial
47) One way of obtaining increased resistance to stress corrosion
cracking by
a) Relieving compressive stress on the metal surface
b) Creating compressive stress on the metal surface
c) Producing non uniform deformation while cold working during
manufacturing
d) None of these
48) The pickling solution can be
a) H2SO4
b) HCL
c) HNO3
d) All of the above
49) When an anodising surface coating is damaged, it can be partially
restored by
a) Metal polish
b) Complete penetration of air inhibitor
c) Chemical surface treatment
d) Any one of the following
50) MTCS
a) Inter-granular corrosion is attack along the grain boundaries
b) Al-alloy and some stainless steel are particularly susceptible
c) Ultrasonic and radiographic inspection method are used
d) Both a) and b) are correct
51) An ASI is
a) A sensitive differential pressure gauge
b) Indicates differential between the impact and static pressure
surrounding an aircraft
c) Consists of a sensitive metallic diaphragm
d) All of the above
52) Machmeter indicates
a) The ratio of aircraft speed to the speed of sound at any altitude

b) Mechanism is similar to that of True airspeed indicator


c) Mechanism is similar to that of altimeter
d) Both A and B
53) During daily inspection of pitot static system
a) Pitot pressure entry hole, drain holes, static holes, or ports
should be inspected that they are unobstructed
b) Static holes and drains holes must be cleared of obstruction with
tools likely to cause enlargement
c) Both A and B
d) None of the above
54) During Leak test of pitot static system
a) Rate of discharge of pressure should not be at high rate
b) High rate may cause damage to the instruments
c) Both A and B
d) None of the above
55) Leak test provides a means for
a) Check those instruments connected to system, are functioning
properly.
b) It serves as a calibration test also
c) Both A and B
d) None of the above
56) The mechanism of pressure switches are similar to those
employed in
a) ASI
b) Mach meter
c) Altimeter
d) All of the above
57) A gyro having freedom in three planes at right angles to each
other but
controlled by some external force is called
a) Free gyro
b) Tied gyro
c) Earth gyro
d) Rate gyro
58) Ability of gyro to resist any force, which tends to change the
plane of rotation
is termed as
a) Gyroscopic Inertia

b) Gyroscopic Rigidity
c) Gyroscopic Precession
d) Both A and B
59) On application of an external force, the angular change at right
angle to the
applied force is called gyroscopic
a) Rigidity
b) Precession
c) Inertia
d) All of the above
60) The example of earth gyro fitment is
a) Directional gyro
b) Artificial Horizon
c) Turn and bank indicator
d) All of the above
61) While reconditioning a screwdriver blade,
a) Grind the end of the tip first to square with the shank and then
grind the end of the tip to required thickness
b) Grind the blade first to the thickness required and then grind the
end of the tip to square with the shank
c) There may not be any rule for grinding the sequence of grinding
d) None
62) A higher diametral pitch number means
a) A larger tooth size
b) A smaller tooth size
c) It has no relation with the tooth size
d) None
63) Which cross point screwdriver has a taper cross & the sides are
not parallel
a) Phillips screwdriver
b) Reed & prince screwdriver
c) Both are correct
d) None
64) The hallow magnetized shafts of interchangeable screwdrivers hold
hex bits of
a) inch size
b) 3/4 inch size
c) 3/8 inch size
d) inch size

65) The shape of which screwdriver permits the use of a wrench to


assist in tightening?
a) Stubby screwdriver
b) Phillips screwdriver
c) Heavy duty screwdriver
d) Double ended screwdriver
66) Prick punch has an included angle of
a) 15o
b) 45o
c) 65o
d) 90o
67) While installing a taper pin with a pin punch, the size of the punch
should be
a) Larger than the size of the pin
b) Smaller than the size of the pin
c) Same size of the pin
d) Can be of any size
68) What do you mean by a stub tooth?
a) Same as involute tooth
b) It gives smoother operation than involute tooth
c) It is thicker in proportion to its length than the involute tooth
d) As in c& is preferred where strength is not important
69) Which hammers are used for riveting & stretching of metals?
a) Ball peen hammer
b) Straight peen hammer
c) Soft faced hammer
d) Both a& b are correct
70) Soft hammers are made of
1. Babbitt 2. Brass
3. Carbon steel
a) 1, 2 & 3 are correct
b) Only 1 is correct
c) 1, 2 & 4 are correct
d) 1, 2, 3 & 4 are correct

4. Wood

5. Tool steel

Indian Institute of Aircraft Engineering


Mahipalpur, New Delhi
PAPER - II
PART XXI
Answers
1) b
2) a
3) a
4) b
5) c
6) b
7) a
8) d
9) b
10)
11)
12)
13)
14)
15)
16)
17)
18)
19)
20)
21)
22)
23)
24)
25)
26)
27)
28)
29)
30)
31)
32)
33)
34)
35)

c
c
c
b
c
c
a
d
a
a
b
a
a
a
b
a
a
a
a
a
a
d
a
c
c
a

B-11

36)
37)
38)
39)
40)
41)
42)
43)
44)
45)
46)
47)
48)
49)
50)
51)
52)
53)
54)
55)
56)
57)
58)
59)
60)
61)
62)
63)
64)
65)
66)
67)
68)
69)
70)

c
b
a
c
b
b
a
b
b
c
b
b
d
c
d
d
d
a
c
a
d
b
d
b
b
a
b
a
d
c
b
a
c
a
c

PAPER - II
PART XXII
1. Velocity of trans verse wave is
a) Equal to sound wave
b) Twice of sound wave
c) Half of sound wave
d) There is no relation between transverse wave and sound wave
2. Frequency chosen for defect scanning in ultrasonic depend upon
a) Size of the object
b) Possible location of defect
c) Grain size of material
d) All of these
3. Thin sheet metals weld defect can be inspected by
a) X-Ray
b) Ultrasonic method
c) Eddy current
d) None of these
4. Longer wavelength of x-ray beam have quality of
a) More penetrating power
b) Less penetrating power
c) As in b) and indicated by half value layer
d) As in a) and indicated by full value layer
5. By which method we cannot detect the inter-granular corrosion
easily
a) Ultrasonic method
b) Eddy current
c) Magnetic particle
d) X-Ray
6. Grinding cracks on small radius bends is appeared as _____ in
magnetic particle inspection.
a) Irregular lines over affected area
b) Short parallel lines
c) Dotted patch
d) Scattered small lines
7. What are the advantages of Eddy current testing
a) Does not require extensive preparation of parts

b) Parts can be checked in Insitu condition


c) It do not interfere with other parts
d) All of the above
8. Permeability of material is the function of
a) Magnetizing force
b) Flux density
c) Both a) and b) are correct
d) None of the above
9. Sand blasting is not done on
a) Steel
b) Cast aluminium cylinder head
c) Where strength is not primary concern
d) Copper
10. Which instrument is used for checking the surface roughness?
a) Spectrometer
b) Prosfetrometer
c) Profilometer
d) Hilsegmetometer
11. In computer machine level language is
a) A High Level Language
b) Low Level Language
c) Very High Level Language
d) None
12. A modern computer uses
a) Decimal language
b) Binary language
c) Hexadecimal language
d) All of the above
13. When data has to be read, the control structure will be
a) In sequence
b) In sequence and repetition
c) Repetition and sequence
d) None of them
14. Universal Gates are
a) AND & OR Gates
b) NAND & NOR Gates
c) NOT & NAND Gates

d) Ex. OR & Ex. NOR Gates


15. The binary conversion of 11.75 is
a) 1101.10
b) 1011.11
c) 1110.01
d) 1001.11
16. Basic function of computer is
a) Addition
b) Subtraction
c) Multiplication
d) Division
17. The conversion of (010100)2 into Octal is
a) (24)8
b) (28)8
c) (26)8
d) (50)8
18. A computer consists of
a) Printer, Decoder, Memory
b) Input, Output, CPU
c) Input, Output, Printer
d) None of the above
19. Computer viruses can spread from one computer to another by
means of
a) An infected disk
b) Links to a network
c) Any electronic communication medium
d) All of the above are correct
20. FORTRAN & COBOL are
a) High Level Language
b) Assembly Language
c) Machine Language
d) Fourth Generation Language
21. If the shunt field of a compound generator is connected across
both the armature and series field, then the connection is said to be
a) Long shunt connection
b) Short shunt connection
c) Parallel connection
d) Both a and b

22. Three wire generators are designed to deliver


a) 240 or 120 volts from either side of the neutral wire
b) 120 volts or 360 volts
c) 220 V or 440 V
d) Both a and c

23. The distortion of the magnetic field is called


a) Armature reaction
b) Field reaction
c) Both a and b
d) None of these
24. For parallel operation, the generators normally preferred are
a) Shunt generators
b) Series generators
c) Both a and b
d) Compound generator
25. In D.C generators, a inter pole field coils are connected
a) In series with armature winding
b) In parallel with armature winding
c) In series with load
d) In parallel with load
26. In D.C generators the brushes are always placed along
a) Magnetic neutral axis
b) Geometrical neutral axis
c) Bisector of GNA and MNA
d) There is no hard and fast rule for this
27. The range of paper capacitor is given by
a) 200 micro micro farads to several micro farads
b) 400 micro farads to 20 micro farads
c) 1 micro farad to 1000 micro farads
d) 200 micro farads to 400 micro farads
28. In radio and radar transmitters we generally prefer to use
a) Oil capacitor
b) Paper capacitor
c) Mica capacitor
d) Electrolyte capacitor

29. The range of mica capacitor is


a) 50 micro micro farads to 0.02 micro farads
b) 10 micro farad to 40 micro farads
c) Greater than 40 micro farads
d) None of these

30. Can we apply KVL for AC circuit


a) Yes
b) No
c) At low frequency we can apply
d) Both a and c
31. Clamper is used to
a) Cut any portion of AC cycle
b) Shift its DC level
c) Change the frequency
d) Adjust the AC level
32. The output is high only when both input are different. The device
is
a) AND gate
b) NAND gate
c) EXOR gate
d) EXNOR gate
33. A FET is a device, which is
a) Current driven
b) Voltage driven
c) Power driven
d) None
34. The condition for sustaining oscillations in resonant circuit is
a) XL > XC no feed back
b) R = XL and +VE feedback
c) XL=XC and positive feedback
d) R=XC no feedback
35. The oscillator, which does not employ LC tank circuit
a) Hartlay

b) Collpit
c) Crystal
d) Clapp
36. Advantage of modulation is
a) Low frequency signals can be sent over long distance
b) Size of antenna is greatly reduced
c) No interference with other transmitters
d) All of the above
37. In frequency modulation
a) The amplitude changes while frequency constant
b) The frequency changes while amplitude constant
c) Both constant
d) Both vary
38. If the signal frequency band is between 550 1500 KHz., and
local oscillator frequency band [1045 1995] KHz then I.F. will be
a) 405 KHz
b) 495 KHz
c) 500 KHz
d) 1000 KHz
39. In conductor
a) Valence band is empty only
b) Conduction band is full only
c) Both are overlapped
d) VB, CB never combined
40. Two resistors (R1, R2) of 30 and 20 ohms respectively, are
connected in parallel across a 20V source. The current through R1
branch would be
a) 12A
b) 10A
c) 0.8A
d) 0.66A
41. A primary cause of inter-granular corrosion is
a) Improper heat treatment
b) Dissimilar metal contact
c) Improper application of primer
d) All of the above

42. The lifting or flaking of the metal at the surface due to delamination of grain boundaries caused by the pressure of corrosion
residual product build-up is called
a) Brinelling
b) Granulation
c) Exfoliation
d) All of the above
43. Tubular members are protected
a) Internally and externally
b) Internally during assembly and sealed to prevent accumulation
of moisture.
c) Ultrasonic and Radiological method gives indication of reduction
of thickness during inspection
d) All of these
44. If extra strength is required and clearance permit
a) Round head rivet may be used
b) Flat head rivet may be used
c) Counter sunk rivet may be used
d) It does not matter
45. The rivet fault shown is
a) Insufficient hammering
b) Dolly not square
c) Snap not square
d) Incorrect snap
46. The rivet fault shown is
a) Hole too large
b) Insufficient hammering
c) Incorrect snap
d) Snap not square
47. The washer used with castle and castellated shear nut is
a) Lock washer
b) Plain washer
c) Flat washer
d) Both b) and c)
48. Corrosion should be removed on Mg-alloy component with
a) Metallic bristle brush
b) Nylon scrubber
c) Carborundum paper

d) Plain scrapper
49. The type of corrosion that is generally present in aircraft but not
visible is
a) Exfoliation
b) Fretting
c) Electrolytic
d) Inter-surface
50. Metals are graded as per electrode potential. Thus the most
anodic material will
a) Give up electron more easily
b) Corrode much faster
c) Resist corrosion
d) Both a) and b)
51. The example of tied gyro fitment is
a) Artificial Horizon
b) Directional Gyro
c) Turn and Bank indicator
d) None of the above

52.
a)
b)
c)

The turn and Bank indicator is called


Turn and slip indicator
Needle and ball indicator
Shows correct execution of a bank and turn and indicate the
lateral attitude of aircraft in level flight
d) All of the above

53.
a)
b)
c)
d)

Turn pointer of TSI is operated by a gyro driven by


Vacuum
Air pressure
Electricity
All of the above

54. TSI is normally consisting electrical driven gyro so in case of


failure of vacuum driven artificial horizon and direction indicator, it acts
as
a) Safety factor
b) Stand by instrument for emergency operation
c) Both A and B

d) None of the above


55.
a)
b)
c)
d)

The fluid inside the slip indicator tube of TSI


Provides damping action
Ensuring smooth movement of the ball
Both A and B
None of the above

56. The tube of slip indicator is curved so that horizontal position of


the ball
tends to seek
a) The lowest point
b) The highest point
c) Both A and B
d) None of the above
57. In T.S.I a small projection on the left end of tube contains a
bubble of air, which compensates for
a) Expansion of the fluid during change in temperature
b) Contraction of the fluid during change in temperature
c) Both A and B
d) None of the above
58. Two stands of wire wound around the glass tube of bank
indicator of T. S. I.
a) Fasten the tube to the instrument case
b) Serve as reference makers
c) Indicates the correct position of ball in the tube
d) All of the above
59. During coordinated straight and level flight, the force of gravity
causes the ball to rest
a) In the lowest part of the tube
b) Centered between the reference wires
c) Both A and B
d) None of the above
60.
a)
b)
c)
d)

Fast erection switch should not be pressed


Before 15 seconds have elapsed after switching on the supply
For more than one minute at a stretch
Both A and B
None of the above

61. Faces of soft hammers are specified by

a)
b)
c)
d)

Degree of hardness
Diameter of face & length of head
Weight of the head without the handle
None

62. In aviation maintenance, the most popularly used drive sizes of


sockets are
a) 1/4 & 3/8 inch
b) 3/8 & 5/8 inch
c) 1/4 & 3/16 inch
d) 1/4 & 5/8 inch
63. Crows foot sockets are available with
a) Open ends only
b) Closed ends only
c) Flare nut ends only
d) All of the above are correct
64. Adjustable tap wrenches are available to hold taps & reamers of
a) About 1/2 inch size
b) 1/2 5/8 inch size
c) All sizes
d) None
65. The size range of Allen wrench is
a) 3/64 3/8 inch
b) 3/8 - 5/8 inch
c) 3/8 - 1 inch
d) 3/64 - 1/2 inch

66. The offset angle of the open end of a tool post wrench is
a) 15 degrees
b) 22
c) 0 degree
d) None
67. Speed handles can be used for turning
a) Screws much faster than conventional screwdrivers
b) Nuts much faster than conventional wrench
c) Nuts much faster than conventional ratchet wrench
d) All of the above are correct

68. The bottoming tap


a) Is tapered back for 6 to 7 threads
b) Is tapered back for 2 to 3 threads
c) Is tapered back upto its shank
d) None
69. Which type of reamer has less-tendency to chatter?
a) Straight fluted reamer
b) Spiral fluted reamer
c) Both a and b
d) None
70. A hand drill can be used to drill holes
a) Upto 3/8
b) Upto
c) 1/8
d)

Indian Institute of Aircraft Engineering


Mahipalpur, New Delhi
PAPER - II
PART XXII
1. c
2. d
3. a
4. c
5. d
6. b
7. d
8. c
9. d
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.

c
b
b
b
b
b
a
a
b
d
d
a
a
a
a
a
a
a
a
a
a
b
c
b
c
c
d
b

B-11

38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
68.
69.
70.

b
c
d
a
c
d
a
b
b
d
b
c
d
b
d
d
c
c
a
a
d
c
c
a
a
d
c
d
c
d
d
b
b

PAPER - II
PART XXIII
1. Which letter show as process code for achromatise
a) A
b) B
c) C
d) D
2. Symbol indicate
a) Electrical s/w
b) Chemical s/w
c) Electrolytic s/w
d) Electro-thermal s/w
3. Which nut is used to prevent other nuts from turning on threaded
bolt or rod
a) Self-locking nut
b) Jamb nut
c) Stainless steel nut with cotter pin
d) None of these
4. The content of CO2 fire extinguisher or N2 pressurized extinguisher
is checked by
a) Weight and pressure gauge
b) Marking on neck
c) By operating the extinguisher
d) All of the above
5. Choose incorrect statement
a) Yellow poly propylene provide insufficient strength
b) Proper tension in rope allows 1 movement
c) Manila rope requires extra slack due to shrinks
d) The rope from tail should pull away at about 45o to each side
of tail
6. Which type of jack is used for L/G retraction check
a) Single base jack
b) Bottle neck jack
c) Screw jack
d) Tripod jack

7. Which measuring tool is used for outside or inside measurement for


faster work
a) Vernier micrometer
b) Vernier calliper
c) Micrometer calliper
d) None of these
8. Which is incorrect statement
a) If corrosion is present in control cable should be replaced
b) Cable used in seaplane must be coated with paral-ketone
c) For detection of corrosion, cable twist in same way of lay
d) Carbon steel cable must be used with protective coating
9. After welding aluminium parts flux should be removed by
a) Immersing them in Luke warm water for 30 minutes
b) Mechanical means, i.e. Wire brushing as the flux is not soluble
in water
c) Washing the parts in boiling water containing 5% HNO3
d) Vacuum blasting
10.

11.
a)
b)
c)
d)

A gusset is
a) A bracing between longerons
b) A type of connecting bracket
c) Used for fail safe construction
d) Like a butt plate
The unit where calculations are preferred is called
Central Processing Unit (CPU)
Control Unit
Arithmetic and Logic Unit (ALU)
Computing Unit

12.
a)
b)
c)
d)

EDP stands for


Electrical data processing
Electronic data processing
Entry data processing
Electronic discrete Programme

13.
a)
b)
c)
d)

Assembler is
An individual who assembles computer
Language
Program
None

14.
a)
b)
c)
d)

Input unit of computer communicates between


Operator and Computer
Memory with printer
CPU with monitor
Output and computer

15.
a)
b)
c)
d)

The Symbol for Hexadecimal is


2
8
10
16

16.
a)
b)
c)
d)

In computer terminology, MICR means


Magnetic Ink Character Recognition
Magnetic Ink Computer Recognition
Monitor Indicating Computer Relay
Mass Information Computer Record

17.
a)
b)
c)
d)

Speed of processor is measured in


Kilobit/Sec
Hertz
Byte
RPM

18.
a)
b)
c)
d)

A byte is a group of
2 bits
4 bits
8 bits
16 bits

19.
a)
b)
c)
d)

In digital computer system, number of states used is


2
3
8
16

20.
a)
b)
c)
d)

The term ROM means


Random Operation Memory
Read and Operate Memory
Read Only Memory
None

21. The energy of a capacitor having capacitance C and voltage V


is given by

a)
b)
c)
d)

0.5 CV2
CV
C2V
0.5 C2V

22.
a)
b)
c)
d)

One unit of magnetic flux is given by


Weber
Weber per meter square
Square root of Weber
Hennery

23.
a)
b)
c)
d)

Generators works on the principle of


Faradays law of electromagnetic induction
Ohms law
Biot-severts law
Gausss law

24.
a)
b)
c)
d)

The Capacitor of a parallel plate is given by


A /d
A2 / d
Ad /
None of these

25. If there are N number of cells, each having voltage E and


internal resistance r are connected in series, then the resulting
e.m.f of the circuit is given by
a) NE volt
b) E/N volt
c) E volt
d) NEr volt
26. The phase difference between voltage and current in a purely
resistive circuit is given by
a) 0o
b) 90o
c) 45o
d) 135o
27. One micro farad is equal to
a) 0.001 milli farad
b) 100 milli farad

c) 1000 milli farad


d) 10 milli farad
28.
a)
b)
c)
d)

The ability of magnet to restore magnetism is called


Retentivity
Permitivity
Store ability
Both a and c

29. If Im is the maximum current for sine AC then its R.M.S value is
given by
a) 0.707 Im
b) Im
c) 0.5 Im
d) 1.414 Im
30. The relationship between voltage and current in a purely
inductive circuit is given by
a) Voltage leads the current by 90o
b) Current lags the voltage by 90o
c) Both a and b
d) None of these
31.
a)
b)
c)
d)

By voltage division rule the voltage drop V1 in the circuit will be


V1=(R2*VS) / (R1+R2)
V1=(R1*VS) / (R1+R2)
V1=VS*(R1+R2) / R1
None

32. If inductance is doubled and the capacitance is halved, then


resonant frequency F0
a) Doubled
b) Halved
c) Remains Same
d) Squared root of F0
33.
a)
b)
c)
d)

50000000Hz stands for


5 MHz
0.5 MHz
50 MHz
5000 MHz

34.

To smoothen the DC in rectifier, we employ

a)
b)
c)
d)
35.
a)
b)
c)
d)

LPF
HPF
BPF
None
The Voltage / Current across the short circuit
V=max
I=0
V=0
I=max
V=0
I=0
V=max
I=max

36. The vacuum tube has


a) Directly heated anode
b) Indirectly heated cathode
c) Directly heated cathode
d) Indirectly heated anode
37. For aircraft generation plant inductor is 1H. The value of
capacitor should be
a) 1 / (800 )2 farad
b) (800 ) farads
c) (400 ) farads
d) 800 farads
38.
a)
b)
c)
d)

In one time constant, the capacitor charges to


36.8% of its maximum value
63.2% of its maximum value
98% of its maximum value
None

39.
a)
b)
c)
d)

The name Superhet is used for


AM receiver
FM receiver
AM transmitter
FM transmitter

40. Two resistances of 15, 12 ohms each are connected in parallel


across a supply, giving 27 ampere., then current through 15 ohm
will be
a) 27 amp
b) 12 amp
c) 15 amp
d) 1 amp
41. Most effective method of removing rust from ferrous metal is
a) Steel wire brush

b) Sand paper
c) By abrasive blasting
d) Washing with hot shop solution
42. A) Rivet smaller than 3/32 diameter are never used on stressed
structure
B) Never replace 2024T rivet with 2117T rivet.
a) Both are correct
b) Both are incorrect
c) Only A) is correct
d) Only B) is correct
43.
a)
b)
c)
d)

Regarding permanent ballast


Lead bar or plate is used
Painted red and placarded
Bolted as near as possible to CG
Both A and B

44.
a)
b)
c)
d)

Transverse pitch is
Twice the rivet diameter
70% of rivet pitch
75% of rivet pitch
6-8 diameter

45.
a)
b)
c)
d)

Rivet pitch is
Distance between center of rivet in a row
Distance between edge to center of rivet
Four times the rivet diameter
Both a) and c) are correct

46.
a)
b)
c)
d)

Edge distance (minimum) is


4D
2D
6-8D
Any of the above

47.
a)
b)
c)
d)

The amount of rivet length used for shop head is


1 x diameter of rivet
4 x diameter of rivet
3 x diameter of rivet
All of the above

48.
a)
b)
c)
d)

Which plating process provide excellent base for paint


Cd Plating
Zn Plating
Granodizing
All of the above

49.
a)
b)
c)
d)

Which treatment give excellent base for paint


CR Plating
Parkerizing
Metal spraying
Zn plating

50. The process use zinc as a medium for plating


a)Parkerizing
b) Sheradizing
c) Galvonizing
d) Both b) and c)
51. The earth rotates at its own axis at a rate of
a) 20 degrees per hour
b) 30 degrees per hour
c) 15 degrees per hour
d) 25 degrees per hour
52. Caging device is used to erect the gyro to its normal operating
condition
a) Prior to flight
b) After tumbling of gyro
c) Both A and B
d) None of the above
53. Gyro horizon
a) Utilizes vertical spin axis gyro
b) Provides visual indications of any change of pitch and roll
attitude of aircraft
c) Both A and B
d) None of the above
54.
a)
b)
c)
d)

With gyro horizon in operation gyro rigidity


Maintains the spin of axis in its normal operating position
Maintains horizon bar with respect to aircraft symbol
A and B both
None of the above

55. In Electrically driven attitude indicators, the gyro rotates


approx., at
a) 20000 rpm
b) 21000 rpm
c) 21500 rpm
d) None of the above
56. During functional test of direction indicator, the drift should be
checked which should not exceed
a) 2 degree in 15 minutes
b) 3 degree in 15 minutes
c) 2 degree in 30 minutes
d) 3 degree in 30 minutes
57.
a)
b)
c)
d)

Performance test of instruments should be carried out


Before installation
At times when indication and operation are suspected
At periods mentioned in aircraft maintenance manual
All of the above

58.
The mounting of the instruments having flangeless cases is
a) From the front of panel
b) Fixing screws and nuts are un-necessary
c) A special type of clamp suited to the instrument case is secured
to the rare of the face of the panel
d) All the above
59.
Direction indicator provides a stabilized directional reference
a) For maintaining a desired course
b) For turning on a new heading
c) Used as complementary instrument to direct reading magnetic
compass
d) All the above
60.
Setting knob at the front of the case of direction indicator is
for
a) Setting the magnetic heading
b) Caging the gyro assembly to prevent the damage during transit
& installation
c) Both a and b
d) None of the above

61. While filing a work piece on the lathe, the file should be held at
an angle of ____ to the work piece
a) 0 degree
b) 10 degree
c) 90 degree
d) 20 degree
62. What should be cutting angle of drill while cutting extremely
hard metals?
a) 59 degree
b) More than 59 degree
c) Less than 59 degree
d) 118 degree
63.
a)
b)
c)
d)

The angle of the flute of a drill in relation to the work is the


Cutting angle
Lip angle
Web angle
Rake angle

64.
a)
b)
c)
d)

What do you mean by thinning the point of a drill?


Decrease the width of the dead centre
Increase the width of the dead centre
Decrease the blade angle of the drill
Decrease the lip clearance of the drill

65. What will be the result if the angles of the cutting edges of a drill
are equal but the lips are of unequal length?
a) The drill will bind on one side of the hole
b) The hole will be larger than the drill
c) Both the points and the lip will be off centre
d) Both b and c are correct
66. A centre drill is used
a) For drilling holes of accurate size
b) For drilling a short drilled hole and countersink hole in one
operation
c) As in b and has an included angle of 65 degree
d) None

67. Which reamer is considered as a rough reamer?


a) Rose reamer

b) Shell reamer
c) Chucking expansion reamer
d) Jobbers reamer
68.
a)
b)
c)
d)

Worm threads have a thread angle of


45 degrees and is similar to ACME threads
29 degrees and is similar to ACME threads
29 degrees and depth of threads are deeper than ACME threads
29 degrees and ACME threads are deeper than worm threads

69. In the picture, if the torque to be applied to the fastener is 225


inch-pounds, then what should be the pointer of the wrench read?
a) Around 260 inch -pounds
b) 150 inch pounds
c) 225 inch- pounds
d) 180 inch -pounds

70. The figure shown here is of


a) A simple gear train and the gear D moves at half speed of gear
A
b) As in a & and the gear D moves in the same direction of the
gear A
c) A compound gear train & the gear D moves in the opposite
direction of the gear A
d) A simple gear train and the gear D moves in the opposite
direction at a double speed of gear A
100T

30 30

50T
D

PAPER - II
PART XXIII
1. b
2. c
3. b
4. a
5. a
6. d
7. b
8. c
9. c
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.

b
c
b
c
a
d
a
b
c
a
c
a
a
a
a
a
a
a
a
a
c
b
c
c
a
b
b
a
b
a
b
c
c

43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
68.
69.
70.

d
c
d
b
a
c
b
d
c
c
c
c
b
b
d
d
d
c
b
b
d
a
d
b
a
c
d
d

PAPER - II
PART XXIV
1. All submerged parts & hull of seaplane is sprayed with liquid lanoline
upto height of _____________ above water line
(a) 1 Feet
(b) 2 Feet
(c) 1 meter
(d) 2 meter
2. Mark the correct statements
a)Steel wool is used on Al-alloy for corrosion removal
b)Clad-Al can be cleaned by mechanical method
c)Trichloroethylene is used for removal of grease
d)All of the above
3. Evidence of surface corrosion and extent of pitting should be tested by
(a) Hardness testing
(b) Impact testing
(c) Probing with a fine needle
(d) None of these
4. Exhaust of Aero-engine made of stainless formed ________________
due to high temperature
(a) Crevice corrosion
(b) Electrolytic corrosion
(c) Inter-granular corrosion
(d) Stress corrosion
5. Which type of corrosion is occurred in mounting bolts of engine and
wings ?
(a) Inter-granular corrosion
(b) Stress corrosion
(c) Concentrating cell corrosion
(d) Fettling corrosion
6. Heated section checked with magnet for corrosion detection, basically
that indicate their relative
(a) Conductivity of part
(b) Permeability of part
(c) both (a) and (b)
(d) None of these
7. Which is most suitable condition for storage of Aircraft part?
(a) Less than 60% humidity
(b) Equal to 60% humidity
(c) More than 60% humidity
(d) None of these
8. Paint stripper is removed with
(a) Steel wool
(c) Aluminium wool

(b) Emery cloth


(d) Non-metallic material

9. Which type of stripper is used on plastic or windows parts?

(a) Water-miscible paint remover


remover
(c) Both (a) & (b)

(b) Solvent-miscible paint


(d) None of these

10.

Anodic film can be removed by a solution of


a) 10% Sulphuric acid + 4% Potassium fluoride
b) 20% Sulphuric acid + 10% Potassium fluoride
c) 20% Sulphuric acid + 20% Potassium fluoride
d) All of the above

11.

Chromate film treatment is carried on __________ material


(a) Al-alloy
(b) Mg-alloy
(c) Steel-Alloy
(d) Titanium

12.

Cadmium plating can be removed by


(a) Mechanical cleaning
(b) Chemical cleaning
(c) Both (a) & (b)
(d) None of these

13.
Mark the correct statement regarding chemical cleaning of steel
a)
Corrosion on steel can be removed by pickling solution
b)
Phosphoric acid can also be used
c) As in (b), it dissolved oxide film and partly inhibit the steel surface
d) All of the above
14.
Mark the correct statement regarding chemical cleaning of Alalloys
a) Light corrosion can be removed by solvent
b) Heavy deposits on clad Al-alloy can be removed chemically
c) Heavy deposits on non-clad Al-alloy can be removed mechanically
d) All of the above
15.
Which of the following corrosion remover required a followed-up
action of chromate bearing conversion coating treatment?
(a) Chromic-acid corrosion remover
(b) Phosphoric-acid corrosion remover
(c) Butyl alcohol + Isopropyl alcohol + water
(d) Nitric acid + water
Which acid is used for cleaning of Mg-alloy?
(a) Chromic acid
(b) Phosphoric acid
(c) Nitric acid
(d) Sulphuric acid
16.

Steel and Non-clad Al-alloy can be cleaned by


(a) Wet glass paper
(b) Dry emery paper
(c) Dry sand paper
(d) As in (a) & water acts as
lubricants

17.
Which type of scraper is used for corrosion removal on casting or
forging parts?
(a) Steel carbide tipped
(b) Plastic copped tip
scraper
(c) Abrasive tipped cap scraper
(d) None of these
18.
Mark the correct statement regarding battery component
a)Lead-acid battery compartment neutralized by bi-carbonate of soda
b) Ni-Cd battery compartment neutralized by acetic acid
c) The sump vent jar containing moist absorbent pad with neutralizing
agent
d) All of these
19.
Human wastes corrode the lavatory area, because it is ________
in nature
(a) Acidic
(b) Caustic
(c) Neutralizing agent
(d) None of these
20.

Grip length of the bolt is


(a) Total length of the bolt
(b) Plain sank portion of the bolt
(c) Length under the head of the bolt to the end of the bolt
(d) None of these

21.

In close tolerance bolt, force applied to drive in is


(a) 10 ounce hammer
(b) 20 ounce hammer
(c) 12 to 14 ounce hammer
(d) Sledge hammer

22.

AN 4-7 bolt shows


(a) 7/8 dia
(b) length
(d) dia

23.

Bolt of class 4 fit is


(a) Loose fit
(c) Close fit

(c) 4length

(b) Free fit


(d) Tight fit

24.

Special washer AC 950 and AC 955 are used where


(a) Bolt is installed at angle to surface
(b) Bolt is
installed head down
(c) It can be used any where
(d) None of these
25.
To prevent the crushing surface on wooden structure with nut
and bolt, the washer used is
(a) AN 936
(b) AN 935
(c) AN 970
(d) AN 960

26.

Where shear load is taken by the bolt, the nut used is


(a) Plain nut
(b) Castle nut
(c) Castellated shear nut
(d) Self locking nut

27.
In the patch repair of the Aircraft skin, the edge distance
(distance from the centre of the rivet to the edge of the sheet) should
be (d is diameter of rivet)
(a) 2d to 4d
(b) 8d
(c) 6d
(d) 75% of
the pitch
28.

Pitch of the rivet should be


(a) 1 d
(c) 1 x d

(b) 6d to 8d
(d) All of these

29.
The amount of the length required to form the head of the rivet
is
(a) 2 d
(b) 4 d
(c) 1 x d
(d) 8 d
30.

Chamfering of the patch plate is done at the angle of


(a) 25
(b) 45
(c) 60
(d) 15

31.
In patch repair, clearance between the rivet and hole should be
(a) 0.008
(b) 0.5
(c) 0.002 to 0.004
(d)
0.4
32.
A rivet with part no. AN 470 AD 3-5 is having a diameter of
(a) 3/32
(b) 5/32
(c) 3/16
(d) 5/16
33.
Seam welding is
(a) Pressure welding
(c) Electric resistance

(b) Non-pressure welding


(d) Both (a) & (c)

34.
In which type of welding, the electrode is non-consumable
(a) TIG
(b) MIG
(c) Electric resistance
(d) Oxyacetylene
35.
Spot welding electrodes should be
(a) Good conductor of Electricity
heat
(c) High strength & Hardness
36.
In leftward welding
(a) Filler rod precedes torch
rod
(c) A 60 V is prepared at the end of plate

(b) Good conductor of


(d) Both (a) & (c)
(b) Torch precedes filler
(d) Both (a) & (c)

37.
The color of acetylene cylinder and oxygen cylinder is
(a) Maroon & Black
(b) Black & Maroon
(c) Yellow & Black
(d) Black & Yellow
38.
Bi-Planer block in Chain assembly is used for changing the plane
of articulation through
(a) 120
(b) 90
(c) 180
(d)
None
39.
For Non-reversible chains, mark the correct statement
(e)
Every third inner plate is extended in one direction
(f) Every second outer plate is extended in one direction
(g)
Every fourth outer plate is extended in both direction
(h)
All are wrong

PAPER - II
PART XXIV
ANSWERS :
1B

2C

3C

4C

5D

6B

7A

8D

9C

10A

11B

12C

13D

14D

15B

16A

17D

18A

19D

20A

21C

22A

23D

24C

25B

26C

27A

28A

29C

30C

31C

32A

33D

34D

35A

36D

37A

38A

39

40

PAPER - II
PART XXV
1. If electrolyte from a lead acid battery is split in the battery
compartment, which procedure should be followed
(a) Apply boric acid solution to the affected area followed by the water
rinse
(b) Rinse the affected area thoroughly with the clean water.
(c) Apply sodium-bi-carbonate solution to the affected area followed by
the water rinse
(d) All of the above
2. Which of the following can provide the empty weight on an aircraft if the
aircrafts weight and balance record become lost, destroyed or otherwise
inaccurate
(a) Re-weighing the aircraft
(b) Aircraft specification
(c) Type certificate datasheet
(d) Flight manual
3. The useful load of an aircraft consists of
(a) Crew, useable fuel, passengers and cargo
(b) Crew, useable fuel, oil and fixed equipments
(c) Crew, passengers, useable fuel, oil, cargo and fixed equipments
(d) None of the above
4. The maximum weight of an aircraft is
(a) Empty weight + crew, maximum fuel weight
(b) Maximum fuel weight, cargo, baggage and passenger
(c) Empty weight + crew, passengers and fixed equipments
(d) Empty weight + useful loads
5. Zero fuel weight is
(a) Dry weight + the weight of full crew, passenger and cargo
(b) Basic operating weight without crew, fuel and cargo
(c) Maximum permissible weight of a loaded aircraft without fuel
(d) None of the above
6. Amount of fuel used for computing empty weight and corresponding C.G
is
(a) Empty fuel tanks
(b) Useable fuel
(c) The amount of fuel necessary for half hour of operation
(d) Full tank fuel

7. Two boxes which weigh 10 pounds and 5 pounds are replaced in an


airplane so that their distance from C.G are 4 feet and 2 feet respectively.
How far forward of the C.G should a third box weighing 20 pounds be
placed so that the C.G will not be changed.
(a) 3 feet
(b) 2.5 feet
(c) 3.5 feet
(d) 8 feet
8. Flexible hose used in aircraft system is classified with
(a) Outside diameter
(b) Wall thickness
(c) Inside diameter
(d) Outside dia-inside dia
9. Scratch or Nicks on the straight portion of aluminium alloy tubing may
be repaired if they are no deeper than
(a) 20% of the wall thickness
(b) 1/32 inch or 20% of wall thickness, whichever is less
(c) 10% of the wall thickness
(d) None of these
10. When installing bonded clamps to support metal tubing
(a) Paint should be removed
(b) Paint clamp and tube after installation
(c) Leave as it is
(d) Remove paint or anodizing from tube and clamp location
11. A 3/8 inch aircraft high pressure flexible hose as compare to 3.8 inch
metal tubing used in the same system will
(a) Have about the same outer diameter
(b) Have equivalent flow characteristic
(c) Usually have interchangeable application
(d) Have same internal diameter
12. What method of magnetic particles inspection is used often to inspect
aircraft parts for invisible cracks
(a) Residual
(b) Inductance
(c) Intermittent
(d) Continuous
13. In performing a dye-penetrate inspection, the developer
(a) Act as blotter to produce a visible indication
(b) Seeps into a surface crack to indicate the presence of cracks
(c) Thoroughly cleans the surface prior to the inspection
(d) Perform no function
14. What type of corrosion attacks grain boundary of aluminium alloy which
are improperly or inadequately heat treated
(a) Filiform
(b) Intergranular
(c) Fretting
(d) Strain

15. Unless otherwise specified or required, aircraft bolts should be installed


so that the bolt head is
(a) Upward or in a forward direction
(b) Downward or in a forward direction
(c) Downward or in a rearward direction
(d) Upward or in a rearward direction
16. A bolt with a single raised dash on the head is classified as an
(a) AN corrosion resistance steel
(b) NAS standard aircraft bolt
(c) NAS closed tolerance bolt
(d) Magnetic resistance bolt
17. A bolt with an X-inside a triangle on the head is classified as an
(a) AN corrosion resistance steel bolt
(b) NAS aircraft bolt
(c) NAS closed tolerance bolt
(d) Aluminium bolt
18. Which tool can be used to measure the alignment of a rotor shaft or
the plain of rotation of a disc
(a) Dial indicator
(b) Shaft gauge
(c) Protector
(d) Micro meter
19. Weather waning tendency is greatest than taxying
(a) Either type of aeroplane in a quartering tail wind
(b) A tail wheel type aeroplane in a direct cross wind
(c) In a nose wheel type aeroplane quartering head wind
(d) A tail wheel type aeroplane parallel wind
20. When taxying an aircraft, an alternating red and green light from the
control tower means
(a) Move clear of the runway/taxy way immediately
(b) OK to proceed but used extreme caution
(c) Return to starting point
(d) Stop where are
21. The color of 100 ll fuel is
(a) Blue
(b) Colorless or straw
(c) Red
(d) Green
22. A fuel that does not vaporize readily enough can cause
(a) Vapour lock
(b) Detonation
(c) Hard starting
(d) None
23. Nickel cadmium battery case and drain surfaces which have been
affected by electrolyte should be neutralized with a solution of

(a) Boric acid


(c) Potassium hydroxide

(b) Sodium bi-carbonate


(d) Sodium chloride

24. Corrosion caused by galvanic action is the result of


(a) Excessive Anodization
(b) Contact between two unlike
metals
(c) Excessive etching
(d) Surface carburization
25. Which material is the most acidic
(a) Cadmium
(b) Magnesium

(c) Copper

(d) Gold

26. Speed of sound in the atmosphere


(a) Varies according to the frequency of sound
(b) Varies according to the temperature
(c) Varies according to the pressure
(d) All of the above
27. Aspect ratio of a wing is defined as the ratio of
(a) Wing span to the wind root
(b) Square of the chord to the wing span
(c) Wing span to the mean chord
28. A wing with a very high aspect ratio will have
(a) Low drag at high angles of attack
(b) A low stall speed
(c) Good control at low speed
(d) All of the above
29. Vicious cycle is connected to
(a) Nickel cadmium battery
(c) Dry cell

(b) Sulphuric acid battery


(d) None of the above

30. Basically corrosion reduces the strength of materials by the process of


(a) Chemical reaction
(b) Electrochemical reaction
(c) Both (a) & (b)
(d) Electromagnetic process
31. Evidence corrosion on stainless steel is an appearance of
(a) Brown color rust
(b) Green color scum
(c) White color debris
(d) None of these
32. When corrosion product is removed from surface corrosion, then which
type of corrosion is appeared on it?
(a) Oxidation corrosion
(b) Dry corrosion
(c) Pitting corrosion
(d) Wet corrosion
33. The metal that is oxidized due to the corrosion attack that is called as
(a) Neutralized agent
(b) Anodic change

(c) Cathodic change

(d) None of these

34. Mark the correct statement:


(a) Under corrosive environment, most active metal become cathodic
(b) Under influence of corrosive agent less active metal become anodic
(c) Established condition for corrosion due to the presence of anode and
cathode is called as local cell
(d) All of the above are true
35. Types of corrosion depends upon
(a) Type of materials
(c) Shape of metal

(b) Size of metal


(d) All of the above

36. Crevice corrosion is an example of


(a) Surface corrosion
(b) Concentration cell corrosion
(c) Electrolytic cell corrosion
(d) Exfoliation corrosion
37. Which type of corrosion occurs in high-strength materials used as
brackets, attached to Al-alloy skin of aircraft
(a) Galvanic corrosion
(b) Fretting corrosion
(c) Stress corrosion
(d) Dry corrosion
38. Coca is formed in which type of corrosion?
(a) Filiform corrosion
(b) Exfoliation corrosion
(c) Fretting corrosion
(d) Microbial corrosion
39. Which type of corrosion will occur in welded parts?
(a) Stress corrosion
(b) Inter-crystalline corrosion
(c) Fretting corrosion
(d) Dissimilar metal corrosion
40. Stress corrosion can be prevented by
(a) Shot-penning
(b) Shot-bursting
(c) As in (a) & increase in the fatigue strength
(d) As in (a) & increase in the tensile strength

PAPER - II
PART XXV
ANSWERS:
1

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30C

31D

32C

33B

34C

35D

36B

37A

38C

39B

40C

PAPER - II
PART XXVI
1. In tapered sectioned metal piece, which area is more susceptible to
corrosion
(a) Exterior surface
(b) Interior surface
(c) Thin portion
(d) Thick portion
2. Mark the correct statement:
(a) Inter-crystalline corrosion occurs along grain boundaries of an alloy
(b) This is a from of electrochemical attack
(c) As in (b) & occurs due to lack of uniformity
(d )All of the above
3. Stress corrosion can be detected by
(a) Eddy current
(c) X-ray

(b) Dye-penetrant
(d) Ultrasonic method

4. Speed of electro-chemical attack is increased in _________ climate


(a) Hot and dry
(b) Cold and moist
(c) Hot & moist
(d) Cold & dry
5. Which type of acid is produced by electrical sparks when combined with
moisture in confined spaces?
(a) Sulphuric acid
(b) Nitric acid
(c) Phosphoric acid
(d) Chromic acid
6. Which type of corrosion is present in contact area of metal and non-metal
joint?
(a) O2 concentration cell corrosion
(b) Metal ion concentration cell corrosion
(c) Filiform corrosion
(d) Crevice corrosion
7. Mark the correct statement:
(a) The fungus grows at the fuel/water interface
(b) As in (a) & temperature range is in between 50-60F.
(c) As in (b) & this occurs in integral fuel tank
(d) As in (c) & this produces a microbial corrosion
8. Which corrosion is occurred due to improper heat-treatment and welding
defects?
(a) Metabolic corrosion
(b) Inter-granular corrosion
(c) Trans-granular corrosion
(d) Weld decay corrosion

9. Which of the following coating function as sacrificial protection?


(a) Chromium plating
(b) Galvanizing
(c) Cladding
(d) Metal spraying
10. Which nut is used to prevent other nuts from turning on threaded bolt or
rod
(a) Self-locking nut
(b) Jamb but
(c) Stainless steel nut with cotter pin
(d) None of these
11. The content of CO2 fire extinguisher or N2 pressurized extinguisher is
checked by
(a) Weight and pressure gauge
(b) Marking on neck
(c) By operating the extinguisher
(d) All of the
above
12. Choose incorrect statement:
(a) Yellow polypropylene provide insufficient strength
(b) Proper tension in rope allows 1 movement
(c) Manila rope requires extra slack due to shrinks
(d) The rope requires extra slack due to shrinks
13. Which type of jack is used for L/G retraction check
(a) Single base jack
(b) Bottle neck jack
(c) Screw jack
(d) Tripod jack
14. Which measuring tool is used for outside or inside measurement for
faster work
(a) Vernier micrometer
(b) Vernier caliper
(c) Micrometer caliper
(d) None of these
15. Which is incorrect statement
(a) If corrosion is present in control cable should be replaced
(b) Cable used in seaplane must be coated with para-ketone
(c) For detection of corrosion, cable twist in same way of lay
(d) Carbon steel cable must be used with protective coating
16. After welding aluminium parts flux should be removed by
(a) Immersing them in like warm water for 30 minutes
(b) Mechanical means, i.e. wire brushing as the flux is not soluble in
water
(c) Washing the parts in boiling water containing 5% HNO 3
(d) Vacuum blasting
17. A gusset is
(a) A bracing between longerons
bracket
(c) Used for fail safe construction

(b) A type of connecting


(d) Like a butt plate

18. The unit where calculations are preferred is called


(a) Central processing unit (CPU)
(b) Control Unit
(c) Arithmetic and logic unit (ALU)
(d) Computing unit
19. EDP stands for
(a) Electrical data processing
processing
(c) Entry data processing
programme

(b) Electronic data


(d) Electronic discrete

20. Assembler is
(a) An individual who assembles computer
(b) Language
(c) Program
(d) None of the above
21. Input unit of computer communicates between
(a) Operator and Computer
(b) Memory with printer
(c) CPU with monitor
(d) Output and Computer
22. The symbol for Hexadecimal is
(a) 2
(b) 8
(c) 10

(d) 16

23. In computer terminology, MICR means


(a) Magnetic Ink Character Recognition
(b) Magnetic Ink Computer Recognition
(c) Monitor Indicating Computer Relay
(d) Mass Information Computer Record
24. Speed of processor is measured in
(a) Kilobit / Sec
(b) Hertz
25. A byte is a group of
(a) 2 bits
(b) 4 bits

(c) 8 bits

(c) Byte
(d) 16 bits

26. In digital computer system, number of states used is


(a) 2
(b) 3
(c) 8
27. The term ROM means
(a) Random Operation Memory
Memory
(c) Read only Memory

(d) RPM

(d) 16

(d) Read and Operate


(d) None

28. The energy of a capacitor having capacitance C and voltage V is given


by

(a) 0.5 CV2


0.5 C2V

(b) CV

(c) C2V

(d)

29. One unit of magnetic flux is given by


(a) Weber
(b) Weber per meter square
(c) Square root of Weber
(d) Henery
30. Generators works on the principle of
(a) Faradays law of electromagnetic induction
(b) Ohms law
(c) Biot - severts law
(d) Gausss law
31. The Capacitor of a parallel plate is given by
(a) Ac / d
(b) A2C / d
(c) Ad / c

(d) None

32. If there are N number of cells, each having voltage E and internal
resistance r are connected in series, then the resulting e.m.f of the circuit is
given by
(a) NE volt
(b) E/N volt
(c) E volt
(d) NEr volt
33. The phase difference between voltage and current in a purely resistive
circuit is given by
(a) 0
(b) 90
(c) 45
(d) 135
34. One micro farad is equal to
(a) 0.001 milli farad
(c) 1000 milli farad

(b) 100 milli farad


(d) 10 milli farad

35. The ability of magnet to restore magnetism is called


(a) Retentivity
(b) Permitivity
(c) Store ability
(d) both (a) & (c)
36. If Im is the maximum current for sine AC then its R.M.S value is given
by
(a) 0.707 Im
(b) Im
(c) 0.5 Im
(d) 1.414 Im
37. The relationship between voltage and current in a purely inductive circuit
is given by
(a) Voltage leads the current by 90
(b) Current lags the voltage by 90
(c) both (a) & (b)
(d) None of the above
38. By voltage division rule the voltage drop V1 in the circuit will be
(a) V1 = (R2 x Vs) / (R1+R2)
(b) V1 = (R1 x Vs) / (R1+R2)

(c) V1 = Vs x (R1+R2) / R1
(d) None
39. If inductance is doubled and the capacitance is halved , then resonant
frequency F0
(a) Doubled
(b) Halved
(c) Remains same
(d) Squared root of F0
40. 50000000 Hz stands for
(a) 5 MHz
(b) 0.5 MHz
MHz

(c) 50MHz

(d) 500

PAPER - II
PART XXVI

ANSWERS:
1D

2D

3B

4C

5B

6D

7A

8B

9C

10B

11A

12A

13D

14B

15C

16C

17B

18C

19B

20C

21A

22D

23A

24B

25C

26A

27C

28A

29A

30A

31A

32A

33A

34A

35A

36A

37C

38B

39C

40 C

Você também pode gostar