Escolar Documentos
Profissional Documentos
Cultura Documentos
Date
Author
Reviewer
Notes
Wang
V1.0
2014/04/20
Haifeng,
Liu
Gu Yuhui
First edition
Yinghui
Adds optimization function:Control
V1.1
2016/04/07
YangYiqin
Gu Yuhui
TABLE OF CONTENTS
1
2
2.1
2.2
2.3
Overview ............................................................................................................ 4
Feature Introduction ............................................................................................. 4
License Control .................................................................................................... 6
Correlation With Other Features .......................................................................... 6
Parameters....................................................................................................... 11
5
5.1
5.2
6
6.1
6.2
6.3
6.4
6.5
Abbreviation .................................................................................................... 19
Reference Document....................................................................................... 20
FIGURES
Figure 6-1 GSM Cell Configuration ....................................................................................17
Figure 6-2 GSM Cell Configuration ....................................................................................17
Figure 6-3 E-UTRAN Measurement Configuration .............................................................18
Figure 6-4 Deactivating Fast Return ..................................................................................19
TABLES
Table 2-1 License Control List ............................................................................................ 6
Table 4-1 Parameter List ...................................................................................................11
Feature Attribute
BSC version: [ZXG10-iBSC (V6.30.30)]
BTS version: [Only for the SDR platform]
Attribute: [Optional]
Involved NEs:
NE Name
Related or Not
MS
BTS
BSC
iTC
MSC
MGW
SGSN
GGSN
HLR
Special Requirement
: involved
-: not involved
Overview
2.1
Feature Introduction
In the areas with both LTE and GSM deployed, a terminal preferentially resides in an LTE
cell. The terminals that have established services may transfer from LTE to GSM for
some reason such as mobility. In most cases, a terminal returns to IDLE state after
releasing the service in the GSM network, and triggers a location area update procedure.
After that, the terminal reselects an LTE cell based on cell reselection parameters, and
triggers a tracking area update procedure. If many terminals that have established
services transfer from LTE to GSM, two location registration procedures triggered by
each terminal not only add signaling load to the core network, but also increase the
duration in which the terminal cannot be paged.
ZTE GSM products can send LTE cell information through the Cell selection indicator
after release of all TCH and SDCCH indicator in a Channel Release message when a
GSM/LTE terminal releases a call in GSM. With the LTE cell information, the terminal
directly reselects an LTE cell, instead of returing to GSM and then reselecting an LTE cell.
Thus one location area update procedure in GSM is avoided.
In UR12, the operator can determine whether a suitable LTE neighbor cell for a terminal
to fast return to is selected based on measurement reports. If a terminal reports multiple
acceptable LTE neighbor cells, the BSS selects the cell with the highest level among all
the acceptable LTE neighbor cells and sends the cell information to the terminal.
Meanwhile, the BSS can set cell reselection parameters specified for fast return to LTE,
which are independent of cell reselection parameters from GSM to LTE in IDLE state.
This enhanced feature needs to be supported by GSM/LTE dual-mode terminals.
In UR13, the operator can determine whether fast return from GSM to LTE only applies
to Circuit Switched Fallback (CSFB) calls. If this feature applies to CSFB only, the BSC
triggers fast return from GSM to LTE based on the CSFB indicator in a Clear Command
message sent from the MSC, and enables the terminals with CSFB calls to fast return
from GSM to LTE after the calls end. For non-CSFB calls, fast return from GSM to LTE is
not performed. This enhanced feature needs to be supported by the core network.
In order to improve the network index, sometimes hope can according to user level
situation before release, deciding whether to redirect to LTE network. So, in order to
ensure that 2G index may require the low level users to return to the LTE network, the
high level users stay in GSM network. When the GSM coverage is better than LTE, in
order to ensure the overall network benefits, may require high level users try to return to
the LTE, and the low level of the user is still retained in the GSM.
2.2
License Control
Table 2-1
Feature ID
ZGO-02-03--014
Feature Name
License
Configured
Control Item
NE
Fast Return
GSM to LTE
from GSM to
BSC
Unit
TRX
LTE
2.3
Technical Description
Based on 3GPP TS45.008, if the Cell selection indicator after release of all TCH and
SDCCH parameter is carried in the channel release message, a terminal tries to reside in
the indicated cell, which may be a 2G cell, a UTRAN cell, or an E-UTRAN cell, and
accelerates the procedure by using the measurement results on the dedicated channels
of these neighbor cells. This feature is called redirection or fast return.
When fast return from GSM to LTE is required, the BSC sets the E-UTRAN cells in the
channel release message in two ways: based on configuration only, and based on
measurement results. If the LTE neighbor cells are set based on configuration only, the
MS must measure the cells before residing in one of them, which may affect the speed
and accuracy. If the LTE neighbor cells are set based on the measurement results on the
dedicated channels, the speed and accuracy of fast return can be increased further. If
the LTE neighbor cells are set based on measurement results, the cell information must
be broadcasted for the MS to measure the dedicated channels of these cells. Now the
LTE neighbor cell information is broadcasted in both the Measurement Information
message and 2quater message.
LTE neighbor cells contain FDD cells and TDD cells. The operator can determine
whether TDD cells or FDD cells are preferentially selected for fast return by setting
parameters.
The measurement results of LTE neighbor cells are reported in two formats: 3-bit format
in a common measurement report, and 6-bit format in an enhanced measurement report.
The reported measurement value may be RSRP or RSRQ, which can be configured by
parameters. After receiving the measurement results of LTE neighbor cells, the BSC
averages the results.
When CS services are released, the BSC carries E-UTRAN neighbor cell information or
not to instruct the MS to redirect to LTE based on the FastReturn to LTE parameter.
When the switch support carrying E-UTRAN neighbor cells in the Channel Release
message, and then determine the switch (Control FastReturn by RXLEV), if the switch is
closed, the optimization function does not work, continue to process according to the
original process. When the switch is open, the average value of downlink level from the
current serving cell for judgment, if the level value is in the range of "FastReturn high /
low threshold, it enabled FastReturn, carrying the E-UTRAN neighbor information in the
Channel Release message. If the power level value is not in the range, it is not enable
FastReturn function.
When E-UTRAN neighbor cell information needs to be carried, the E-UTRAN neighbor
cells are selected based on the RelEUtranStrategy and RelEUtranPrio parameters and
terminal capability. The rules are described as follows:
from the configuration. If no E-UTRAN FDD neighbor cell is configured, the BSC
does not select any E-UTRAN neighbor cell.
BSC also support CSFB based FastReturn and SRVCC based FastReturn function.
When the parameter (FastReturn to LTE) is set to " Channel Release with E-UTRAN
Neighbour Cell When CSFB " or " Channel Release with E-UTRAN Neighbour Cell When
CSFB and SRVCC ", E-UTRAN neighbor cell information is carried only when a CSFB
indicator.When the parameter (FastReturn to LTE) is set to " Channel Release with
E-UTRAN Neighbour Cell When SRVCC " or " Channel Release with E-UTRAN
Neighbour Cell When CSFB and SRVCC ", E-UTRAN neighbor cell information is carried
only when a SRVCC indicator, try to let mobile phone FastReturn to LTE.
10
Parameters
Table 4-1
Paramet
er Name
Parameter List
Defau
GUI Name
Parameter Description
Value Range
lt
Unit
Value
Recommend
ed Value
0:Channel
Release without
E-UTRAN
Neighbour Cell
This
1:Channel
parameter
Release with
should be set
E-UTRAN
according to
Neighbour Cell
the network
2:Channel
configuration
Release with
and operator
E-UTRAN
requirements.
Neighbour Cell
GGsmCe FastReturn all TCH and SDCCH" indication in
When CSFB
the Channel Release message can
ll
to LTE
3:Channel
carry LTE neighbor cell information
Release with
to let the terminal return to LTE
E-UTRAN
network,this parameter is for
Neighbour Cell
control if LTE neighbor cell is
When SRVCC
carried.
4:Channel
In a GSM/LTE
None 0
network, it is
recommende
d to use fast
return so as to
reduce the
time required
for the MS to
Release with
return to the
E-UTRAN
LTE network.
Neighbour Cell
When CSFB and
SRVCC
Strategy for
E-Utran
GSMCE Neighbour
LL
Select
When
Release
Generally, set
0:According to
this
measurement
parameter to
1:According to
Config
None 1
0. If MSs are
not expected
2:Prefer
to measure
measurement
E-Utran
neighbor cells
11
Paramet
er Name
Defau
GUI Name
Parameter Description
Value Range
lt
Unit
Value
Recommend
ed Value
and thus
there are
measuring
GSM/UTRAN
E-UTRAN
parameter to
release message.
1. In this
case, E-Utran
neighbor cell
release
selection is
not precise.
Set this
GSMCE
LL
parameter
E-Utran
neighbor
FDD and
TDD Prio
When
Release
based on the
None 0
network
condition and
telecom
operator's
requirement.
completion.
RxLevel
0: below - 98dBm
1: below - 94dBm
2: below - 90dBm
None 15
15
3: below -86dBm
12
Paramet
er Name
Defau
GUI Name
Parameter Description
Value Range
lt
Unit
Recommend
ed Value
Value
Neighbour
4: below -82dBm
Cell In
0-6) or higher
5: below -78dBm
Dedicated
6: below -74dBm
Mode
7: always
starts
calculating
average
value of
E-Utran
1..20
None 4
Cell
Neighbour
Cell
Set this
offset to the
parameter to
reported
value when offset to the reported value when
GEutran prioritizing prioritizing the FDD E-UTRAN cells
0..7
for
Measure the FDD
E-UTRAN
6bit reporting
a larger value
if FDD
None 0
E_UTRAN
neighbor cell
are
expected to
be reported in
13
Paramet
er Name
Defau
GUI Name
Parameter Description
Value Range
lt
Unit
Recommend
ed Value
Value
priority.
offset to the
reported
value when offset to the reported value when
GEutran prioritizing prioritizing the TDD E-UTRAN cells
0..7
for
Measure the TDD
E-UTRAN
None 0
None 0
None 0
6bit reporting
3bit reporting
3bit reporting
parameter
Control
should be set
according
the
0: No
to
network
configuration
and operator
1:Yes
High
GGsmCe RxLevel
ll
None 0
requirements.
This
parameter
should be set
0..63
None 63
according
to
14
Paramet
er Name
Defau
GUI Name
Parameter Description
Value Range
lt
Unit
Value
Recommend
ed Value
the
network
configuration
and operator
requirements.
FastReturn
should
be
users
which
downlink
Rx
to
network
configuration
Low
GGsmCe RxLevel
ll
and operator
requirements.
FastReturn
should
be
users
which
downlink
Rx
None 0
5.1
Related Counters
Counter ID
requirements.
Name
15
5.2
C901110114
C901110115
C901110116
Related Alarms
This feature has no related alarm.
Engineering Guide
6.1
Application Scenario
This feature applies to hybrid GSM/LTE networking.
6.2
16
Figure 6-1
In the configuration resource tree, select Managed Element > GSM Logical
Configuration > Cell Information Configuration and double-click GSM Cell
Configuration. In the right pane, select the corresponding record. The GSM Cell
Configuration tab is displayed, see 2. Set Strategy for E-Utran Neighbour Select
When Release and E-Utran FDD and TDD Prio When Release parametes.
Figure 6-2
In the configuration resource tree, select Managed Element > GSM Logical
Configuration > Cell Information Configuration and double-click E-UTRAN
17
Measurement. In the right pane, select the corresponding record. The E-UTRAN
Measurement tab is displayed, see Figure 6-3. Set the corresponding parameters.
Figure 6-3
6.3
Prerequisite
1.
2.
3.
4.
Steps
1.
2.
3.
Expected Result
18
6.4
6.5
Abbreviation
Abbreviation
Full Name
rd
3GPP
CCN
E-UTRAN
LTE
NACC
19
RRC
TA
Tracking Area
TDD
FDD
GSM
CSFB
SRVCC
Reference Document
ZXG10 iBSC (V6.30.30) Base Station Controller Performance Counter Reference
ZXG10 iBSC (V6.30.30) Base Station Controller Radio Parameter Reference
20