Você está na página 1de 5

April 2001

Process Industry Practices


Piping

PIP PN03SD0J01
Piping Material Specification 3SD0J01
Class 300, 316/316L Stainless Steel, 0.000" C.A.
Core: Process
Jacket: Steam

PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES


In an effort to minimize the cost of process industry facilities, this Practice has
been prepared from the technical requirements in the existing standards of major
industrial users, contractors, or standards organizations. By harmonizing these
technical requirements into a single set of Practices, administrative, application, and
engineering costs to both the purchaser and the manufacturer should be reduced. While
this Practice is expected to incorporate the majority of requirements of most users,
individual applications may involve requirements that will be appended to and take
precedence over this Practice. Determinations concerning fitness for purpose and
particular matters or application of the Practice to particular project or engineering
situations should not be made solely on information contained in these materials. The
use of trade names from time to time should not be viewed as an expression of
preference but rather recognized as normal usage in the trade. Other brands having the
same specifications are equally correct and may be substituted for those named. All
Practices or guidelines are intended to be consistent with applicable laws and
regulations including OSHA requirements. To the extent these Practices or guidelines
should conflict with OSHA or other applicable laws or regulations, such laws or
regulations must be followed. Consult an appropriate professional before applying or
acting on any material contained in or suggested by the Practice.

This Practice is subject to revision at any time by the responsible Function Team
and will be reviewed every 5 years. This Practice will be revised, reaffirmed, or
withdrawn. Information on whether this Practice has been revised may be found at
http://www.pip.org.

2001 Process Industry Practices (PIP), Construction Industry Institute,


The University of Texas at Austin, 3208 Red River Street, Suite 300, Austin,
Texas 78705. PIP member companies and subscribers may copy this Practice
for their internal use. Changes, overlays, addenda, or modifications of any
kind are not permitted within any PIP Practice without the express written
authorization of PIP.

Not printed with State funds

PIP PN03SD0J01
Piping Material Specification Line Class 3SD0J01

April 2001
SERVICE:
RATING CLASS:
TEMPERATURE LIMIT:
NOMINAL CORROSION ALLOWANCE:

Core: Process
Jacket: 150 psi Steam
300, ASME B16.5-1996
-20F to 800F
0.000 in.

MATERIAL:
DESIGN CODE:
STRESS RELIEF:
EXAMINATION:

Core: 316/316L Dual Marked


Jacket: 304/304L Dual Marked
ASME B31.3c-1998
None Required
Per ASME B31.3

600
316

700
371

800
427

PRESSURE - TEMPERATURE RATINGS - CORE


TEMP F
TEMP C

-20 to 100
-29 to 38

200
93

300
149

400
204

500
260

For NPS 1/2 through NPS 12 (Full flange rating per ASME B16.5, Table 2-2.2)
psig
kPag

720
4965

620
4275

560
3860

515
3550

480
3315

450
3105

430
2965

420
2895

400
204

500
260

600
316

700
371

800
427

PRESSURE - TEMPERATURE RATINGS - JACKET


TEMP F
TEMP C

-20 to 100
-29 to 38

200
93

300
149

For NPS 1 through NPS 14 (Pressure is limited by external pressure on 4 inch sch 10S 316/316L core pipe)
psig
kPag

270
1860

ITEM
PIPE

260
1795
NOTES
01

Core

Jacket
Tubing - Jumper
NIPPLES

251
1730

242
1670

231
1595
ENDS

221
1525

210
1450

199
1370

NPS

SCH/RAT

DESCRIPTION

1/2 3/4
14
6 12
1 14
1/2 3/4
1

40S
10S
40S
10S
0.049 in.
0.065 in.

SS, EFW, ASTM A312-TP 316/316L (Ej=0.80)


SS, EFW, ASTM A312-TP 316/316L (Ej=0.80)
SS, EFW, ASTM A312-TP 316/316L (Ej=0.80)
SS, EFW, ASTM A312-TP 304/304L (Ej=0.80)
SS, SMLS, ASTM A269-TP 316 annealed (Ej=1.0)
SS, SMLS, ASTM A269-TP 316 annealed (Ej=1.0)

1/2 2

40S

SS, EFW, ASTM A312-TP 304/304L (Ej=0.80)

83
Branch

FITTINGS

02

CORE
Reducer (CONC)
Reducer (ECC)
90 LR ELL
45 LR ELL
Tee
Tee (RED)
Cap
JACKET
Reducer (CONC)
Reducer (ECC)
90 SR ELL
45 SR ELL
Tee
Tee (RED)
Cap

85
85
85
85
85
85

1/2 12
1/2 12
1/2 12
1/2 12
1/2 12
1/2 12
1/2 12

Weld
Weld
Weld
Weld
Weld
Weld
Weld

SS, ASTM A403-WP 316-W/316L-W, ASME B16.9


SS, ASTM A403-WP 316-W/316L-W, ASME B16.9
SS, ASTM A403-WP 316-W/316L-W, ASME B16.9
SS, ASTM A403-WP 316-W/316L-W, ASME B16.9
SS, ASTM A403-WP 316-W/316L-W, ASME B16.9
SS, ASTM A403-WP 316-W/316L-W, ASME B16.9
SS, ASTM A403-WP 316-W/316L-W, ASME B16.9

1 16
1 16
1 16
1 16
1 16
1 16
1 16

Weld
Weld
Weld
Weld
Weld
Weld
Weld

SS, ASTM A403-WP 304-W/304L-W, ASME B16.9


SS, ASTM A403-WP 304-W/304L-W, ASME B16.9
SS, ASTM A403-WP 304-W/304L-W, ASME B16.28
SS, ASTM A403-WP 304-W/304L-W, ASME B16.28
SS, ASTM A403-WP 304-W/304L-W, ASME B16.9
SS, ASTM A403-WP 304-W/304L-W, ASME B16.9
SS, ASTM A403-WP 304-W/304L-W, ASME B16.9

1/2 1
1/2 1
1/2 1
1/2 1
1/2 1

THRD
THRD
SW
Weld
THRD

Tube x tube SS TP 316 SS compression ferrule tube fitting


Tube x FNPT SS TP 316 SS compression ferrule tube fitting
SS, ASTM A182-F316/316L, ASME B16.11
SS, ASTM A182-F316/316L, MSS SP-97
SS, ASTM A182-F316/316L, ASME B16.11

JUMPER
Union
Connector - Female
Half Coupling
SW Pipet
Plug

Process Industry Practices

Class 3000
Class 300
Class 3000

Page 1 of 3

PIP PN03SD0J01
Piping Material Specification Line Class 3SD0J01

ITEM
VALVES
Gate
Gate
Globe
Swing Check
FLANGES
Slip-On (RED)
Slip-On
Insert (RED)
Insert (NON-RED)
Blind

April 2001

NOTES

NPS

SCH/RAT

ENDS

DESCRIPTION

86

1/2 2
1/2 12
1/2 12
1/2 12

Class 800
Class 300
Class 300
Class 300

T/SW
RED-RF
RED-RF

CS body w/ 13 CR trim, HF ST
316 SS body w/ 316 SS trim, FP, w/ jacket
316 SS body w/ 316 SS trim, w/ jacket
316 SS body w/ 316 SS trim, w/ jacket

1/2 14
1/2 14
1/2 14
1/2 14
1/2 14

Class 300
Class 300
Class 300
Class 300
Class 300

RF

1/2 14
1/2 14

Class 300
Class 300

84
09, 82
09, 82, 84

RED-RF

GA08CB200
GA03ST550
GL03ST550
CS03ST550

SS, ASTM A182-F316/316L, ASME B16.5


SS, ASTM A182-F316/316L, ASME B16.5
SS, ASTM A182-F316/316L insert, CS ASTM A105 flange, ASME B16.5
SS, ASTM A182-F316/316L insert, CS ASTM A105 flange, ASME B16.5
SS, ASTM A182-F316/316L, ASME B16.5

RF
RF
RF
RF

GASKETS
Spiral wound type 316L SS, w/ flexible graphite filler, ASME B16.20
Spiral wound type 316L SS, w/ flexible graphite filler, ASME B16.20,
special reducing flange dimensions

BOLTING
Stud Bolts

82

ASTM A193, Gr B7 stud, w/ 2 heavy hex nuts ASTM A194, Gr 2H

90 BRANCH CONNECTION Core vents, drains, and instrument connections only (Note 16)
Legend and Chart

BRANCH SIZE

12

10

1-1/2

3/4

1/2

12

10

1-1/2

3/4

1/2

T
T

HEADER SIZE

B
E
T

Branch Weld
Reducing Tee or Tee and Reducer(s)
Tee

BRANCH SIZE

90 BRANCH CONNECTION Jacket on core branch (to be used with core vent, drain, and instrument connection table)
Legend and Chart
14

12

10

2-1/2

1-1/2

14

12

10

2-1/2

1-1/2

T
T

HEADER SIZE

B
E
T

Branch Weld
Reducing Tee or Tee and Reducer(s)
Tee

Page 2 of 3

Process Industry Practices

PIP PN03SD0J01
Piping Material Specification Line Class 3SD0J01

April 2001

SIZE COMBINATIONS, NPS

NOTES:
01
02
09
16
82
83
84
85
86

Core Pipe

Jacket Pipe

1/2
3/4
1
1-1/2
2
2
3
3
4
6
8
10
12

1
1-1/2
2
2-1/2
3
4
4
6
6
8
10
12
14

Special Jacket
Fittings

12-Elbows
14-Elbows
16-Elbows, 16-Tee

Flange Size,
Reducing Jacket
1 x 1/2
1-1/2 x 3/4
2x1
2-1/2 x 1-1/2
3x2
4x2
4x3
6x3
6x4
8x6
10 x 8
12 x 10
14 x 12

Flange Size,
Non-Reducing Jacket
1/2
3/4
1
1-1/2
2
2
3
3
4
6
8
10
12

Supply, Return,
and Jumper
1/2
1/2
1/2
3/4
3/4
3/4
3/4
3/4
3/4
1
1
1
1

Where pipe schedule is shown under SCH/RAT, it is adequate for the full flange rating. Where Calc is shown, the pressure limit may be lower
than flange rating.
All buttwelded component thicknesses shall match pipe thickness.
Pressure and temperature rating may be limited by certain components permitted by this specification. Refer to manufacturers recommended
pressure-temperature restrictions.
Core branch connections should consist of tees, reducers, and/or reducing tees except in the case of vents, drains, and instrument connections, where
branch welds are permitted per the branch connection tables.
Stud bolt lengths may be longer due to increased thickness of the insert flange.
Threaded joints are permitted only at jacket jumper and instrument connections. Threaded joints shall be seal welded when temperatures exceed 400F.
Use non-reducing flange against equipment or at spec break to piping with non-reducing flange.
Ej = 0.80 when component is split and rewelded.
This valve to be used for jacket vent and drain applications.

REFERENCES:
Process Industry Practices (PIP)
PIP PNF0200 - Vents, Drains, and Instrument Connection Details
PIP PNFJ8000 - Jacketed Pipe Fabrication Details
PIP PNSMV003 - Carbon Steel Gate Valve Descriptions
PIP PNSMV023 - Stainless Steel Gate Valve Descriptions
PIP PNSMV024 - Stainless Steel Globe Valve Descriptions
PIP PNSMV025 - Stainless Steel Check Valve Descriptions

Process Industry Practices

Page 3 of 3

Você também pode gostar