Escolar Documentos
Profissional Documentos
Cultura Documentos
for
HEATSTRIP HEATERS
PRODUCT MANUAL
HEATSTRIP CONTROLS
REV D JUL15
To improve control of Heatstrip outdoor heaters, there are a range of solutions to help you increase the use of
your outdoor entertaining area. The controllers include the following functions:
Wall Switch can be wall mounted, held remotely or junction box mounted to match your decor
INCLUDES:
1 x REMOTE CONTROL
1 x RELAY
1 x SINGLE WALL SWITCH
PART No:
HUSA03
INCLUDES:
1x REMOTE CONTROL
2 x RELAY
1 x DOUBLE WALL SWITCH
RELAY
INCLUDES:
1x SINGLE REMOTE CONTROL
2 x SWITCH
REMOTE CONTROL
INCLUDES:
1x DOUBLE REMOTE CONTROL
INCLUDES:
1 x REMOTE CONTROL
HUSA03
SINGLE ROCKER SWITCH
SPECIFICATIONS
Can control one heater or one set of heaters
Wireless wall switch
Detachable face plate
Fits inside standard junction box
HUSA04
DOUBLE ROCKER SWITCH
SPECIFICATIONS
Can control two heaters or two sets of heaters
Wireless wall switch
Detachable face plate
Fits inside standard junction box
HUSA05
RELAY
SPECIFICATIONS
Frequency
902MHz
Transmission Range 80ft(25m)
Dimensions
2.78 x 1.65 x 1.1
(73 x 42 x 28mm)
Weight
3.02 Oz (90g)
Compliance
ETL
FCC: SZV-STM300U
IC: 5713A-STM300U
Surge Protection
3000 volts
Line voltage
120, 208. 240 volts
Current
16 amps
INSTALLATION
Can be mounted inside a standard junction box, Attached using a standard knockout and thread connector with
nut (included).
The Relay is to be mounted indoors only and protected from the environment.
Use a non-metal electrical enclosure for best RF transmission.
Install in a suitable location taking care with interference through walls and other obstacles.
When the relay is first installed, the relay will go through a start up sequence., this will take a few seconds, then
it will be ready for programming.
HEATSTRIP
RELAY
240 Volt connection
EARTH
HOT LEG 2
HOT LEG 1
GANG BOX
HEATSTRIP
RELAY
LIGHT TABLE
Menu
Set
solid
Basic set up
Advanced set up
Menu
Set
Option is pending
blink
Active setting
blink
solid
solid
Start, you can now follow the sequence to which ever program
you want
Solid
Set
solid
3. Ready to accept new links, the link will stay open for
2 minutes. The Menu light will continue to blink once
as long as the relay is in the Setup menu.
Solid for 3
seconds
solid
UNLINK SWITCH
Menu
Set
solid
3. Ready to accept new links, the link will stay open for
2 minutes.
1
Menu
Set
3 Blink
Solid for 3
seconds
3 Blink
solid
6. To select an option,
press the set button, the
number of times in the
table. The set button
will flash amber to the
corresponding time peri-
8. The set button will flash the number of times corresponding with the time chosen
Flash
solid
HUSA04
REMOTE CONTROL
SPECIFICATIONS
Small handheld
Can control two heaters or two sets of heaters
RANGE: 80 feet
FREQUENCY: 902 MHz
CHANNELS: 4 buttons ( 2 orckers0
DIMENSIONS: 1.85 x 3.15 x .7 inches
ADDRESSING: Factory set unique ID
(1 of 4 billion)
WIRING DIAGRAMS
All wiring must be carried out by a licensed electrician and according to local building codes.
Diagrams are indicative and must be installed with required isolators, RCDs, fuses, or circuit breakers.
To be installed in conjunction with Product Manual (included in the product box)
HEATSTRIP
RELAY
HEATSTRIP
DOUBLE WALL SWITCH
RELAY
ZONE HEAT
HEATSTRIP
HEATSTRIP
RELAY
HEATSTRIP
RELAY
HEATSTRIP
RELAY
11
DISTRIBUTOR
MANUFACTURER
Heatstrip USA
Enocean
12