Escolar Documentos
Profissional Documentos
Cultura Documentos
1
COPYRIGHT 2011 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
AGENDA
1. Software Installation
2
COPYRIGHT 2011 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
1. Software Installation
3
COPYRIGHT 2011 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Introduction
The 7302 ISAM products come with pre-installed
software. Pre-Installed software can be upgraded to
appropriate release.
If there is no software installed on compact flash (CF)
card of NT card, related image file can be written into
the CF.
Warning:
Responsibility to purchase the necessary hex editor software which will be used
during the operation belongs to participant. Winhex software will not be
supplied to participants, it is not a freeware product!
Alcatel-Lucent is not responsible of the damages which might occur during the
misuse of the program.
Open Win Hex editor and then click on Clone Disk button.
After copying process, please see the ... sector(s) copied pop-up, then click on OK.
Connect DB-9 end of the craft cable to your PC with or without RS232 to
USB converter.
Plug-out and Plug-in the NT card (hard-reset) and wait for the initialization
3. Field Integration
NANT-A
System Management IP & Default Route Configuration
To allow remote connectivity you should configure management IP and
default route address of NANT-A.
leg:isadmin># configure system management host-ip-address manual:172.29.7.215/22
leg:isadmin>configure>system>management# default-route 172.29.4.1
leg:isadmin>configure>system>management>default-route$
NANT-A
Management VLAN and Network Port Configuration
Default management VLAN-id is 4093. Assume that you are going to configure
network port 0.
leg:isadmin># configure interface shub port 0 port-type network
leg:isadmin>configure>interface>shub>port>0# admin-status auto-up
leg:isadmin>configure>interface>shub>port>0# exit all
leg:isadmin># configure vlan shub id 4093 egress-port network:0
If you need to change the management VLAN-id, both the ASAM-core as the
service hub needs to know the management VLAN-id.
leg:isadmin># configure system mgnt-vlan-id 4092
leg:isadmin>configure>system# shub entry vlan ext-vlan-id 4092
NANT-A
Ping the Default Gateway
leg:isadmin># ping 172.29.4.1
PING 172.29.4.1 56 data bytes
64 bytes from 172.29.4.1: icmp_seq=1 ttl=64 time<1ms.
64 bytes from 172.29.4.1: icmp_seq=2 ttl=64 time<1ms.
64 bytes from 172.29.4.1: icmp_seq=3 ttl=64 time<1ms.
64 bytes from 172.29.4.1: icmp_seq=4 ttl=64 time<1ms.
64 bytes from 172.29.4.1: icmp_seq=5 ttl=64 time<1ms.
---- 172.29.4.1 PING Statistics ---5 packets transmitted, 5 packets received, 0% packet loss
round-trip min < 1ms, avg < 1ms, max < 1ms, stddev < 1ms
NANT-A
SNMP Configuration
To make 7302 ISAM manageable from 5520 AMS, SNMP community strings should
be configured.
leg:isadmin># configure system security snmp community public hostaddress 172.29.7.250/22
leg:isadmin>configure>system>security>snmp>community>public>hostaddress>172.29.7.250/22$ exit all
leg:isadmin># configure system security snmp community NETMAN hostaddress 172.29.7.250/22 context shub
leg:isadmin>configure>system>security>snmp>community>NETMAN>hostaddress>172.29.7.250/22$ context shub privilege read-write
NANT-D / NANT-E
System Management IP & Default Route Configuration
The following procedure describes how to configure IP & default route:
1. Configure selected port
NANT-D / NANT-E
Sample of IP & Default Route Configuration
configure port nt-a:xfp:1 ethernet autonegotiate
configure port nt-a:xfp:1 no shutdown
configure service
ies 1 customer 1 create
interface OAM create
address 192.168.0.3/28
sap nt:vp:1:4093 create
exit
exit
no shutdown
exit
vpls 4093 customer 1 v-vpls vlan 4093 create
stp
shutdown
exit
sap nt-a:xfp:1:4093 create
exit
no shutdown
exit
configure router static-route 0.0.0.0/0 next-hop 192.168.0.2
COPYRIGHT 2011 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
NANT-D / NANT-E
Ping the Default Gateway
leg:isadmin># ping 192.168.0.2
PING 192.168.0.2 56 data bytes
64 bytes from 192.168.0.2: icmp_seq=1 ttl=64 time<1ms.
64 bytes from 192.168.0.2: icmp_seq=2 ttl=64 time<1ms.
64 bytes from 192.168.0.2: icmp_seq=3 ttl=64 time<1ms.
64 bytes from 192.168.0.2: icmp_seq=4 ttl=64 time<1ms.
64 bytes from 192.168.0.2: icmp_seq=5 ttl=64 time<1ms.
---- 192.168.0.2 PING Statistics ---5 packets transmitted, 5 packets received, 0% packet loss
round-trip min < 1ms, avg < 1ms, max < 1ms, stddev < 1ms
leg:isadmin>#
NANT-D / NANT-E
SNMP Configuration
The SNMP configuration needs to be done for managing ISAM remotely on 5520
AMS.
Host-address in the configuration for both cases should be the IP address of AMS
server for security reasons.
To configure SNMP:
1. Make sure ping is available.
Ping should be successful from ISAM node to 5520 AMS.
2. Login to CLI interface of ISAM node via Telnet or SSH protocols.
3. Configure the ISAM node SNMP parameter.
Configure SNMP string public for nt context
Configure SNMP string NETMAN for ihub context
NANT-D / NANT-E
SNMP Configuration
To make 7302 ISAM manageable from 5520 AMS, SNMP community strings should
be configured.
leg:isadmin># configure system security snmp community public hostaddress 0.0.0.0/0 context nt
leg:isadmin>configure>system>security>snmp>community>public>hostaddress>0.0.0.0/0# exit all
leg:isadmin># configure system security snmp community NETMAN hostaddress 0.0.0.0/0 context ihub
Plan a board
If the card is not configured, no-planned-board statement should be seen at the
error-status column. Table below shows how to configure cards installed to shelf.
leg:isadmin># configure equipment slot 1/1/1 planned-type nglt-a unlock
leg:isadmin># configure equipment slot 1/1/2 planned-type nglt-a unlock
leg:isadmin># configure equipment slot nt-b planned-type nant-e unlock
Warning: NGLT Board can only be configured with NANT-D/E deployed shelf.
\\NANT-E
leg:isadmin># configure equipment applique ntio-1 planned-type ncnc-f appliqueprofile single_xfp_4_sfp
\\NANT-E
leg:isadmin># show equipment applique
====================================================================================
applique table
====================================================================================
applique |actual-type|enabled|error-status
|availability
---------+-----------+-------+----------------------+-----------------------------------------------ntio-1
ncnc-f
yes
no-error
available
-----------------------------------------------------------------------------------applique count : 1
====================================================================================
Time Configuration
To configure time and date settings
leg:isadmin># admin sntp system-time 2011-07-28:17:58:30
leg:isadmin># show sntp
================================================================================
sntp table
================================================================================
operating-mode : unicast
system-time : 2011-11-22:15:45:34
shub-time : 2011-11-22:15:45:34
================================================================================
Saving Configuration
After configuring the ISAM, the new configuration needs to be saved.
\\NANT-A
leg:isadmin># admin software-mngt shub database save
\\NANT-E
leg:isadmin># admin save
Writing file to /pub/IPD/dm/config.cfg
Saving configuration .... Completed.
leg:isadmin># admin software-mngt ihub database save-protected