Você está na página 1de 37

Document Title

Security Level

CSFB & IRAT


Drive test Case

T01 IRAT Mobility Test..............................................................................................................................


T01-01 CS Fallback to UTRAN.........................................................................................................
2016-11-25

Huawei Proprietary - Restricted Distribution

Page1, Total37

Document Title

1.

Security Level

LTE to UMTS CSFB by using measurement-based PS handover for an idle UE


making a mobile-originated call..........................................................................................

2.

LTE to UMTS CSFB by using measurement-based PS handover for an idle UE


making a mobile-terminated call..........................................................................................

3.

LTE to UMTS CSFB by using measurement-based PS handover for a connected


UE making a mobile-originated call....................................................................................

4.

LTE to UMTS CSFB by using measurement-based PS handover for a connected


UE making a mobile-terminated call.................................................................................

5. LTE to UMTS CSFB by using measurement-based PS handover for LTE UE in idle


mode calling LTE UE in Connected mode 12
6. LTE to UMTS CSFB by using measurement-based PS handover for LTE UE in
connected mode calling LTE UE in Idle mode 14
7.

LTE to UMTS CSFB by using measurement-based redirection for an idle UE


making a mobile-originated call........................................................................................

8.

LTE to UMTS CSFB by using measurement-based redirection for an idle UE


making a mobile-terminated call........................................................................................

9.

LTE to UMTS CSFB by using measurement-based redirection for a connected UE


making a mobile-originated call........................................................................................

10. LTE to UMTS CSFB by using measurement-based redirection for a connected UE


making a mobile-terminated call........................................................................................
11. LTE to UMTS CSFB by using measurement-based redirection for LTE UE in idle
mode calling LTE UE in Connected mode 26
12. LTE to UMTS CSFB by using measurement-based redirection for LTE UE in
connected mode calling LTE UE in Idle mode ..29

T01-02 LTE to UTRAN PS HO & Redirection

2016-11-25

Huawei Proprietary - Restricted Distribution

Page2, Total37

Document Title

Security Level

1. LTE to UMTS PS handover based on coverage with measurement 32


2. LTE to UMTS redirection based on coverage with measurement 34

T01-03 LTE to UTRAN & UTRAN to LTE Reselection


1. LTE to UMTS & UMTS to LTE Reselection based on coverage with measurement 36

1.

IRAT Mobility Test

1.1.1 LOFD-001033 CS Fallback to UTRAN


1. LTE to UMTS CSFB by using measurement-based PS handover for an idle UE
making a mobile-originated call
Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in idle mode by
using PS handover when the UE makes a mobile-originated CS call.
Tools:
1 UMTS&LTE smartphone UE Example: (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example : (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)
Test Count : 20 times
Prerequisites
UE1 is subscribed on the HSS as follows:

2016-11-25

Huawei Proprietary - Restricted Distribution

Page3, Total37

Document Title

Security Level

QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s


Configuration :
To enable CSFB to UTRAN and PS handover to UTRAN and disable blind handover, turn on the
related switches by running the following MML command on the eNodeB:
MOD ENODEBALGOSWITCH: HoAlgoSwitch=UtranCsfbSwitch-1,
HoModeSwitch=UtranPsHoSwitch-1 & BlindHoSwitch-0;
Procedure

Excepted Result

1. Powers on UE1 so that it initiates the


combined attach procedure to LTE
CELL1.

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear in
the S1 tracing result, indicating that the attach
procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing result.
If EPS attach result contained in this message
is combined EPS attach, the attach procedure
is successful.

2. Wait 10s and verify that UE1 is in idle


mode.

The message RRC Connection Release


indicates that UE1 has entered idle mode.

3. Enable UE1 to make a CS call to UE2.


Wait for UE2 to ring.

The eNodeB delivers the inter-RAT


measurement configuration to the UE. The UE
performs inter-RAT measurements. If the
signal quality of CELL2 meets the threshold for
reporting event B1, the UE reports event B1 to
the eNodeB. Then, the eNodeB sends a
handover command to the UE.
RRC_MOBIL_FROM_EURAN_CMD message
can be seen in the LTE Uu interface tracing log
and the PS Handover Complete message can
be seen in the RNC Iu interface tracing log
indicate that the UE is handed over to the
UMTS cell to establish CS call.

2016-11-25

Huawei Proprietary - Restricted Distribution

Page4, Total37

Document Title

4. After UE2 rings, answer the CS call.

Security Level

The CS call is successfully established and the


communication is normal.

5. After Call is finished , then make sure


UE1 is disconnected from the UMTS
network and reselected to the LTE
6. Repeat Step 2, 3 ,4 & 5 for 20 times
OutPut:

Monitor the S1 & UU trace

CSSR, Call setup time and DCR (only the call


dropped within 10S after call established
in 3G will be consider as drop call due to
CSFB and will be analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour

2.

LTE to UMTS CSFB by using measurement-based PS handover for


an idle UE making a mobile-terminated call

Test Preparation
Please backup the configuration of the eNodeB before this test.
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in idle mode by
using measurement-based PS handover when the UE makes a mobile-terminated CS call.
Tools
1 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)
2016-11-25

Huawei Proprietary - Restricted Distribution

Page5, Total37

Document Title

Security Level

Test Count : 20 times


Configuration :
To enable CSFB to UTRAN and PS handover to UTRAN and disable blind handover, turn on
the related switches by running the following MML command on the eNodeB:
MOD ENODEBALGOSWITCH: HoAlgoSwitch=UtranCsfbSwitch-1,
HoModeSwitch=UtranPsHoSwitch-1 & BlindHoSwitch-0;
Procedure

Excepted Result

1. Powers on UE1 so that it initiates the


combined attach procedure to LTE
CELL1.

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the message is encrypted.
Therefore, to verify that the combined attach
is successful, you need to observe the Initial
Context Setup Request message in the UE
logs or MME tracing result. If EPS attach
result contained in this message is combined
eps attach, the attach procedure is
successful.

2. Wait 10s and verify that UE1 is in idle


mode.

The message RRC Connection Release


indicates that UE1 has entered idle mode.

3. Enable UE2 to make a CS call to UE1.


Wait for UE1 to ring.

RRC_MOBIL_FROM_EURAN_CMD
message can be seen in the LTE Uu interface
tracing log and the PS Handover Complete
message can be seen in the RNC Iu interface
tracing log indicate that the UE is handed
over to the UMTS cell to establish CS call.

4. After UE1 rings, answer the CS call.

The CS call is successfully established and


the communication is normal.

5. After Call is finished , then make sure


UE1 is disconnected from the
UMTS network and reselected to
the LTE
2016-11-25

Huawei Proprietary - Restricted Distribution

Page6, Total37

Document Title

Security Level

6. Repeat Step 2 , 3 , 4 & 5


OutPut:

Monitor the S1 & UU trace

CSSR, Call setup time and DCR (only the call


dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour

3.

LTE to UMTS CSFB by using measurement-based PS handover for


a connected UE making a mobile-originated call

Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in connected
mode by using measurement-based PS handover when the UE makes a mobile-originated
CS call.
Tools
1 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)
2016-11-25

Huawei Proprietary - Restricted Distribution

Page7, Total37

Document Title

Security Level

Test Count : 20 times


Configuration :
To enable CSFB to UTRAN and PS handover to UTRAN and disable blind handover, turn on
the related switches by running the following MML command on the eNodeB:
MOD ENODEBALGOSWITCH: HoAlgoSwitch=UtranCsfbSwitch-1,
HoModeSwitch=UtranPsHoSwitch-1 & BlindHoSwitch-0;
Procedure

Excepted Result

1. Powers on UE1 so that it initiates the


combined attach procedure to LTE
CELL1.

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the message is encrypted.
Therefore, to verify that the combined attach
is successful, you need to observe the Initial
Context Setup Request message in the UE
logs or MME tracing result. If EPS attach
result contained in this message is combined
eps attach, the attach procedure is
successful.

2. Make Data application to make UE1 in


Connected mode

Open streaming website or do any data


application to make UE in connected mode

3. Enable UE1 to make a CS call to UE2.


Wait for UE2 to ring.

RRC_MOBIL_FROM_EURAN_CMD
message can be seen in the LTE Uu interface
tracing log and the PS Handover Complete
message can be seen in the RNC Iu interface
tracing log indicate that the UE is handed
over to the UMTS cell to establish CS call.

2016-11-25

Huawei Proprietary - Restricted Distribution

Page8, Total37

Document Title

4. After UE2 rings, answer the CS call.

Security Level

The CS call is successfully established and


the communication is normal.

5. After Call is finished , make sure UE1 is


disconnected from the UMTS
Network and reselected to the LTE
network

6. Repeat Step 2 , 3 , 4 & 5


OutPut:

Monitor the S1 & UU trace

CSSR, Call setup time and DCR (only the call


dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour

4.

LTE to UMTS CSFB by using measurement-based PS handover for


a connected UE making a mobile-terminated call

Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in connected
mode by using measurement-based PS handover when the UE makes a mobile-terminated
CS call.
Tools
1 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
2016-11-25

Huawei Proprietary - Restricted Distribution

Page9, Total37

Document Title

Security Level

Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm , SINR>=15dB,
3G RSCP>=-85dBm , Ec/Io>= -10dB)

Test Count : 20 times


Configuration :
To enable CSFB to UTRAN and PS handover to UTRAN and disable blind handover, turn on
the related switches by running the following MML command on the eNodeB:
MOD ENODEBALGOSWITCH: HoAlgoSwitch=UtranCsfbSwitch-1,
HoModeSwitch=UtranPsHoSwitch-1 & BlindHoSwitch-0;
Procedure

Excepted Result

1. Powers on UE1 so that it initiates the


combined attach procedure to LTE
CELL1.

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the message is encrypted.
Therefore, to verify that the combined attach
is successful, you need to observe the Initial
Context Setup Request message in the UE
logs or MME tracing result. If EPS attach
result contained in this message is combined
eps attach, the attach procedure is
successful.

2. Make Data application to make UE1 in


Connected mode

Open streaming website or do any data


application to make UE in connected mode

3. Enable UE2 to make a CS call to UE1.


Wait for UE1 to ring.

RRC_MOBIL_FROM_EURAN_CMD
message can be seen in the LTE Uu interface
tracing log and the PS Handover Complete
message can be seen in the RNC Iu interface
tracing log indicate that the UE is handed

2016-11-25

Huawei Proprietary - Restricted Distribution

Page10, Total37

Document Title

Security Level

over to the UMTS cell to establish CS call.


4. After UE1 rings, answer the CS call.

The CS call is successfully established and


the communication is normal.

5. After Call is finished , make sure UE1 is


disconnected from the UMTS
Network and reselected to the LTE
network
6. Repeat Step 2 , 3 , 4 & 5 for 20 times
OutPut:

Monitor the S1 & UU trace

CSSR, Call setup time and DCR (only the call


dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour

5.

LTE to UMTS CSFB by using measurement-based PS handover for


LTE UE in idle mode calling LTE UE in Connected mode

Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for 2 LTE UEs , One is in
idle mode Calling to lte UE in Connected Mode
Tools
2 UMTS & LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
2016-11-25

Huawei Proprietary - Restricted Distribution

Page11, Total37

Document Title

Security Level

UE1 is subscribed on the HSS as follows:


QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB

Test Count : 20 times


Configuration :
To enable CSFB to UTRAN and PS handover to UTRAN and disable blind handover, turn on
the related switches by running the following MML command on the eNodeB:
MOD ENODEBALGOSWITCH: HoAlgoSwitch=UtranCsfbSwitch-1,
HoModeSwitch=UtranPsHoSwitch-1 & BlindHoSwitch-0;
Procedure

Excepted Result

1. Powers on UE1 & UE2 so that it


initiates the combined attach
procedure to LTE CELL1.

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.

2. Wait 10s and verify that UE1 is in idle


mode.

The message RRC Connection Release


indicates that UE1 has entered idle mode.

3. Make Data application to make UE2 in


Connected mode

Open streaming website or do any data


application to make UE in connected mode

4. Enable UE1 to make a CS call to UE2.


Wait for UE2 to ring.

2016-11-25

RRC_MOBIL_FROM_EURAN_CMD
message can be seen in the LTE Uu interface
tracing log and the PS Handover Complete
message can be seen in the RNC Iu interface
tracing log indicate that the UE is handed

Huawei Proprietary - Restricted Distribution

Page12, Total37

Document Title

Security Level

over to the UMTS cell to establish CS call.


UE1 is successfully PS handover to UMTS
CELL2 to establish a CS call.
UE2 is successfully PS handover to UMTS
CELL2 to establish a CS call.
5. After UE2 rings, answer the CS call.

The CS call is successfully established and


the communication is normal.

6. After Call is finished , then make Sure


UE1 & UE2 are disconnected from
the UMTS Network and reselected
to the LTE Network
7. Repeat Step 2, 3 , 4 , 5 & 6 for 20 times
OutPut:

Monitor the S1 & UU trace

CSSR, Call setup time and DCR (only the call


dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour

6.

LTE to UMTS CSFB by using measurement-based PS handover for


LTE UE in connected mode calling LTE UE in Idle mode

Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for 2 LTE UEs , One is in
Connected Calling to lte UE in idle mode
Tools :
2 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
2016-11-25

Huawei Proprietary - Restricted Distribution

Page13, Total37

Document Title

Security Level

Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,

Test Count : 20 times


Configuration :
To enable CSFB to UTRAN and PS handover to UTRAN and disable blind handover, turn on
the related switches by running the following MML command on the eNodeB:
MOD ENODEBALGOSWITCH: HoAlgoSwitch=UtranCsfbSwitch-1,
HoModeSwitch=UtranPsHoSwitch-1 & BlindHoSwitch-0;
Procedure

Excepted Result

1. Powers on UE1 & UE2 so that it initiates


the combined attach procedure to
LTE CELL1.

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.

2. Wait 10s and verify that UE2 is in idle


mode.

The message RRC Connection Release


indicates that UE1 has entered idle mode.

3. Make Data application to make UE1 in


Connected mode

Open streaming website or do any data


application to make UE in connected mode

4. Enable UE1 to make a CS call to UE2.


Wait for UE2 to ring.

RRC_MOBIL_FROM_EURAN_CMD
message can be seen in the LTE Uu interface
tracing log and the PS Handover Complete
message can be seen in the RNC Iu interface

2016-11-25

Huawei Proprietary - Restricted Distribution

Page14, Total37

Document Title

Security Level

tracing log indicate that the UE is handed


over to the UMTS cell to establish CS call.
UE1 is successfully PS handover to UMTS
CELL2 to establish a CS call.
UE2 is successfully PS handover to UMTS
CELL2 to establish a CS call.
5. After UE2 rings, answer the CS call.

The CS call is successfully established and


the communication is normal.

6. After Call is finished , then make Sure


UE1 & UE2 are disconnected from
the UMTS Network and reselected
to the LTE Network
7. Repeat Step 2 , 3 , 4 , 5 & 6
OutPut:

Monitor the S1 & UU trace

CSSR, Call setup time and DCR (only the call


dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour

7.

LTE to UMTS CSFB by using measurement-based redirection for an


idle UE making a mobile-originated call

Test Preparation
Please backup configurations before test execution.
Terminal: At least 1 UMTS&LTE smartphone UE and 1 UMTS smartphone UE
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in idle mode by
using measurement-beased redirection when the UE makes a mobile-originated CS call.
Tools :
2016-11-25

Huawei Proprietary - Restricted Distribution

Page15, Total37

Document Title

Security Level

1 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)


1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)

Test Count : 20 times


Configuration :
Enable PS redirection to UTRAN in the obtained inter-RAT handover policy group by running
the following MML command on the eNodeB:
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO0&SRVCC-0&REDIRECTION-1;

Procedure

2016-11-25

Excepted Result

Huawei Proprietary - Restricted Distribution

Page16, Total37

Document Title

1.

Powers on UE1 so that it initiates the


combined attach procedure to LTE
CELL1.

Security Level

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.

2.

Wait 10s and verify that UE1 is in idle


mode.

The message RRC Connection Release


indicates that UE1 has entered idle mode.

3.

Enable UE1 to make a CS call to UE2.


Wait for UE2 to ring.

The eNB sends RRC Connection


Reconfiguration with B1 measurement control
message to UE and receive B1 measurement
from UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface and the Routing Area Update
Request message in the Initial UE message
on the Iu interface indicate that the redirection
successfully.
UE1 is successfully redirected to UMTS
CELL2 to establish a CS call.

4.

After UE2 rings, answer the CS call.

5.

After Call is finished , then make sure


UE1 is disconnected from the UMTS
network and reselected to the LTE

6.

Repeat Step 2, 3 ,4 & 5 for 20 times

OutPut:

The CS call is successfully established and


the communication is normal.

Monitor the S1 & UU trace

CSSR, Call setup time and DCR (only the call


2016-11-25

Huawei Proprietary - Restricted Distribution

Page17, Total37

Document Title

Security Level

dropped within 10S after call


established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour

2016-11-25

Huawei Proprietary - Restricted Distribution

Page18, Total37

Document Title

Security Level

8.LTE to UMTS CSFB by using measurement-based redirection for


an idle UE making a mobile-terminated call
Test Preparation
Please backup configurations before test execution.
Terminal: At least 1 UMTS&LTE UE and 1 UMTS UE
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in idle mode by
using measurement-beased redirection when the UE makes a mobile-terminated CS call.
Tools :
1 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)

Test Count : 20 times


Configuration :
Enable PS redirection to UTRAN in the obtained inter-RAT handover policy group by running
the following MML command on the eNodeB:
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO0&SRVCC-0&REDIRECTION-1;

Procedure

Excepted Result

1. Powers on UE1 so that it initiates the


combined attach procedure to LTE
CELL1.

2016-11-25

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.

Huawei Proprietary - Restricted Distribution

Page19, Total37

Document Title

Security Level

The UE camps on CELL1.


Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.
2. Wait 10s and verify that UE1 is in idle
mode.

The message RRC Connection Release


indicates that UE1 has entered idle mode.

3. Enable UE2 to make a CS call to UE1.


Wait for UE1 to ring.

The eNB sends RRC Connection


Reconfiguration with B1 measurement control
message to UE and receive B1 measurement
from UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface and the Routing Area Update
Request message in the Initial UE message
on the Iu interface indicate that the redirection
successfully.
UE1 is successfully redirected to UMTS
CELL2 to establish a CS call.

4. After UE1 rings, answer the CS call.

The CS call is successfully established and


the communication is normal.

5. After Call is finished , then make sure


UE1 is disconnected from the
UMTS network and reselected to
the LTE
6. Repeat Step 2 , 3 , 4 & 5
OutPut:

Monitor the S1 & UU trace

CSSR, Call setup time and DCR (only the call


dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
2016-11-25

Huawei Proprietary - Restricted Distribution

Page20, Total37

Document Title

Security Level

Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour

2016-11-25

Huawei Proprietary - Restricted Distribution

Page21, Total37

Document Title

9.

Security Level

LTE to UMTS CSFB by using measurement-based redirection for a


connected UE making a mobile-originated call

Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in connected
mode by using measurement-beased redirection when the UE makes a mobile-originated CS
call.
Tools :
1 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)

Test Count : 20 times


Configuration :
Enable PS redirection to UTRAN in the obtained inter-RAT handover policy group by running
the following MML command on the eNodeB:
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO0&SRVCC-0&REDIRECTION-1;

Procedure

Excepted Result

1. Powers on UE1 so that it initiates the


combined attach procedure to LTE
CELL1.

2016-11-25

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.

Huawei Proprietary - Restricted Distribution

Page22, Total37

Document Title

Security Level

The UE camps on CELL1.


Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.
1. Make Data application to make UE1 in
Connected mode

Open streaming website or do any data


application to make UE in connected mode

2. Enable UE1 to make a CS call to UE2.


Wait for UE2 to ring.

The eNB sends RRC Connection


Reconfiguration with B1 measurement control
message to UE and receive B1 measurement
from UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface and the Routing Area Update
Request message in the Initial UE message
on the Iu interface indicate that the redirection
successfully.
UE1 is successfully redirected to UMTS
CELL2 to establish a CS call.

3. After UE2 rings, answer the CS call.

The CS call is successfully established and


the communication is normal.

4. After Call is finished , make sure UE1 is


disconnected from the UMTS
Network and reselected to the LTE
network
5. Repeat Step 2 , 3 , 4 & 5
OutPut:

Monitor the S1 & UU trace

CSSR, Call setup time and DCR (only the call


dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
2016-11-25

Huawei Proprietary - Restricted Distribution

Page23, Total37

Document Title

Security Level

Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour

7.

LTE to UMTS CSFB by using measurement-based redirection for a


connected UE making a mobile-terminated call

Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for a UE in connected
mode by using measurement-beased redirection when the UE makes a mobile-terminated CS
call.
Tools :
1 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
1 UMTS Smartphone UE Example (Huawei U8800)
HUAWEI GENEX Probe for HUAWEI terminals
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,
3G RSCP>=-85dBm, Ec/Io>= -10dB)

Test Count : 20 times


Prerequisites
UE1 is subscribed on the HSS as follows:
QCI = 9 (by default), , ARP = 11, UL and DL AMBRs = 150 Mbit/s
Configuration :
Enable PS redirection to UTRAN in the obtained inter-RAT handover policy group by running
the following MML command on the eNodeB:
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO0&SRVCC-0&REDIRECTION-1;

Procedure

2016-11-25

Excepted Result

Huawei Proprietary - Restricted Distribution

Page24, Total37

Document Title

1. Powers on UE1 so that it initiates the


combined attach procedure to LTE
CELL1.

Security Level

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.

2. Make Data application to make UE1 in


Connected mode

Open streaming website or do any data


application to make UE in connected mode

3. Enable UE2 to make a CS call to UE1.


Wait for UE1 to ring.

The eNB sends RRC Connection


Reconfiguration with B1 measurement control
message to UE and receive B1 measurement
from UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface and the Routing Area Update
Request message in the Initial UE message
on the Iu interface indicate that the redirection
successfully.
UE1 is successfully redirected to UMTS
CELL2 to establish a CS call.

4. fter UE1 rings, answer the CS call.

The CS call is successfully established and


the communication is normal.

5. After Call is finished , make sure UE1 is


disconnected from the UMTS
Network and reselected to the LTE
network
6. Repeat Step 2 , 3 , 4 & 5 for 20 times
OutPut:
2016-11-25

Monitor the S1 & UU trace

Huawei Proprietary - Restricted Distribution

Page25, Total37

Document Title

Security Level

CSSR, Call setup time and DCR (only the call


dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour

8.

LTE to UMTS CSFB by using measurement-based redirection for


LTE UE in idle mode calling LTE UE in Connected mode

Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for 2 LTE UEs by using
measurement-beased redirection when LTE UE in idle mode calling LTE UE in Connected
mode
Tools :
2 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 and UE2 are subscribed on the HSS as follows:
QCI (by default), = 9, ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB,

Test Count : 20 times


Configuration :
Enable PS redirection to UTRAN in the obtained inter-RAT handover policy group by running
the following MML command on the eNodeB:
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO0&SRVCC-0&REDIRECTION-1;
2016-11-25

Huawei Proprietary - Restricted Distribution

Page26, Total37

Document Title

Procedure

Security Level

Excepted Result

1. Powers on UE1 & UE2 so that it initiates


the combined attach procedure to
LTE CELL1.

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.

2. Wait 10s and verify that UE1 is in idle


mode.
3. Make Data application to make
UE2 in Connected mode
Enable UE1 to make a CS call to UE2. Wait
for UE2 to ring.

The message RRC Connection Release


indicates that UE1 has entered idle mode.
Open streaming website or do any data
application to make UE in connected mode
The eNB sends RRC Connection
Reconfiguration with B1 measurement control
message to UE and receive B1 measurement
from UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface and the Routing Area Update
Request message in the Initial UE message
on the Iu interface indicate that the redirection
successfully.
UE1 is successfully redirected to UMTS
CELL2 to establish a CS call.
UE2 is successfully redirected to UMTS
CELL2 to establish a CS call.

After UE2 rings, answer the CS call.


2016-11-25

The CS call is successfully established and

Huawei Proprietary - Restricted Distribution

Page27, Total37

Document Title

Security Level

the communication is normal.


3. After Call is finished , then make Sure
UE1 & UE2 are disconnected from
the UMTS Network and reselected
to the LTE Network
4. Repeat Step 2, 3 , 4 , 5 & 6 for 20 times
OutPut:

Monitor the S1 & UU trace

CSSR, Call setup time and DCR (only the call


dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour

2016-11-25

Huawei Proprietary - Restricted Distribution

Page28, Total37

Document Title

9.

Security Level

LTE to UMTS CSFB by using measurement-based redirection for


LTE UE in connected mode calling LTE UE in Idle mode

Test Preparation
Please backup configurations before test execution.
Objective
This test case aims to verify that the eNodeB performs CS fallback for This test case aims to
verify that the eNodeB performs CS fallback for 2 LTE UEs by using measurement-beased
redirection when LTE UE in Connected mode calling LTE UE in idle mode
Tools :
1 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
Prerequisites
UE1 and UE2 are subscribed on the HSS as follows:
QCI = 9(by default),, ARP = 11, UL and DL AMBRs = 150 Mbit/s
Test Condition :
put static with LTE RSRP>=-85dBm, SINR>=15dB

Test Count : 20 times


Configuration :
Enable PS redirection to UTRAN in the obtained inter-RAT handover policy group by running
the following MML command on the eNodeB:
MOD INTERRATPOLICYCFGGROUP: InterRatPolicyCfgGroupId=3, UtranHoCfg=PS_HO0&SRVCC-0&REDIRECTION-1;

Procedure

Excepted Result

1. Powers on UE1 & UE2 so that it initiates


the combined attach procedure to
LTE CELL1.
2016-11-25

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the

Huawei Proprietary - Restricted Distribution

Page29, Total37

Document Title

Security Level

attach procedure is successful.


The UE camps on CELL1.
Note that the UL NAS TRANS message is
encrypted. Therefore, to verify that the
combined attach is successful, you need to
observe the Initial Context Setup Request
message in the UE logs or MME tracing
result. If EPS attach result contained in this
message is combined eps attach, the attach
procedure is successful.
2. Wait 10s and verify that UE2 is in idle
mode.

The message RRC Connection Release


indicates that UE1 has entered idle mode.

3. Make Data application to make UE1 in


Connected mode

Open streaming website or do any data


application to make UE in connected mode

4. Enable UE1 to make a CS call to UE2.


Wait for UE2 to ring.

The eNB sends RRC Connection


Reconfiguration with B1 measurement control
message to UE and receive B1 measurement
from UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface and the Routing Area Update
Request message in the Initial UE message
on the Iu interface indicate that the redirection
successfully.
UE1 is successfully redirected to UMTS
CELL2 to establish a CS call.
UE2 is successfully redirected to UMTS
CELL2 to establish a CS call.

5. After UE2 rings, answer the CS call.

The CS call is successfully established and


the communication is normal.

6. After Call is finished , then make Sure


UE1 & UE2 are disconnected from
the UMTS Network and reselected
to the LTE Network

2016-11-25

Huawei Proprietary - Restricted Distribution

Page30, Total37

Document Title

Security Level

7. Repeat Step 2 , 3 , 4 , 5 & 6


OutPut:

Monitor the S1 & UU trace

CSSR, Call setup time and DCR (only the call


dropped within 10S after call
established in 3G will be consider as
drop call due to CSFB and will be
analyzed).
Remark
Please resume the configuration of the eNodeB after this test.
Time required: 1 hour

2016-11-25

Huawei Proprietary - Restricted Distribution

Page31, Total37

Document Title

Security Level

T01-02 L2U IRAT


.1

LTE to UMTS PS handover based on coverage with measurement

Objective
This test case aims to verify that the eNodeB supports inter-RAT PS handovers due to
coverage changes.
Tools :
1 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
Test Condition :

Perform downlink data transmission from the FTP Server ,Select One Point at the LTE Cell
edge at RSRP<= -110 , then Start to move from the lte coverage to the UMTS Coverage till
Handover occur from LTE to UMTS

Test Count : 20 times


Prerequisites
The UE is subscribed on the HSS as follows:
QCI = 9 (by default),, ARP = 11, UL and DL AMBRs = 150 Mbit/s
Procedure

Expected Result

Power on the UE so that it initiates the attach


procedure.

The UE attaches to CELL1.

Use FTP tool or Iperf to perform downlink


data transmission.

Data is transmitted properly.

Enable the UE to leave the LTE cell and


approach the UMTS cell until a
handover is triggered.

The UE reports event A2 to the eNodeB. After


receiving the report, the eNodeB delivers the
inter-RAT measurement configuration to the
UE. The UE performs inter-RAT
measurements. If the signal quality of the
UMTS cell meets the threshold for reporting
event B1, the UE reports event B1 to the

2016-11-25

Huawei Proprietary - Restricted Distribution

Page32, Total37

Document Title

Security Level

eNodeB. Then, the eNodeB sends a


handover command to the UE.
The RRC_MOBIL_FROM_EURAN_CMD
message in the LTE Uu interface tracing log
and the Handover to UTRAN Complete in Uu
interface and PS Handover Complete
messages in the RNC Iu interface tracing log
indicate that the UE is handed over to the
UMTS cell.
The data transmission in UMTS side is
normal.
Disconnect the UE and save the logs.
Output :

Operation succeeded.
-

Monitor the S1 & UU trace

Inter-RAT Handover Success Rate


Time Latency

2016-11-25

Huawei Proprietary - Restricted Distribution

Page33, Total37

Document Title

.2

Security Level

LTE to UMTS redirection based on coverage with measurement

Objective
This test case aims to verify that the eNodeB supports inter-RAT redirections due to coverage
changes.
Tools :
1 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals

Test Condition :
Perform downlink data transmission from the FTP Server ,Select One Point at the LTE Cell
edge at RSRP<= -110 , then Start to move from the lte coverage to the UMTS Coverage till
Redirection occur from LTE to UMTS

Test Count : 20 times


Prerequisites
The UE is subscribed on the HSS as follows:
QCI = 9 (by default),, ARP = 11, UL and DL AMBRs = 150 Mbit/s
Procedure

Expected Result

Power on the UE so that it initiates the attach


procedure.

The messages INITIAL UE MSG and the last


UL UE MESSAGE (UL NAS TRANS) appear
in the S1 tracing result, indicating that the
attach procedure is successful.
The UE attaches to CELL1.

Use FTP tool or Iperf to perform downlink


data transmission.

Data is transmitted properly.

Enable the UE to leave the LTE cell and


approach the UMTS cell until a
redirection is triggered.

The UE reports event A2 to the eNodeB. After


receiving the report, the eNodeB delivers the
inter-RAT measurement configuration to the
UE. The UE performs inter-RAT

2016-11-25

Huawei Proprietary - Restricted Distribution

Page34, Total37

Document Title

Security Level

measurements. If the signal quality of the


UMTS cell meets the threshold for reporting
event B1, the UE reports event B1 to the
eNodeB. Then, the eNodeB sends a
redirection command to the UE.
The redirected carrierInfo IE in the
RRC_CONN_REL message on the Uu
interface indicates that the redirection is
triggered successfully.
The Routing Area Update Request message
in the Initial UE message on the Iu interface
indicates that the redirection procedure is
successful.
The data transmission in UMTS side is
normal.
Disconnect the UE and save the logs.
Output:

Operation succeeded.
-

Monitor the S1 & UU trace

Redirection Attempt Success Rate


Time Latency

2016-11-25

Huawei Proprietary - Restricted Distribution

Page35, Total37

Document Title

Security Level

T01-03 LTE to UTRAN & UTRAN to LTE Reselection


1. LTE to UMTS & UMTS to LTE Reselction based on coverage with
measurement
Objective
This test case aims to verify that the eNodeB supports reselection due to coverage changes.
Tools :
1 UMTS&LTE smartphone UE Example (Huawei LTE P1 U9202L-1)
HUAWEI GENEX Probe for HUAWEI terminals
Test Condition :

Make Sure UE are in idle mode , then Select One Point at the LTE Cell edge at RSRP<= -110 ,
then Start to move from the lte coverage to the UMTS Coverage till reselection from LTE to
UMTS occur , then return back from the UMTS Coverage to the LTE Coverage till reselection
from UMTS to LTE is done

Test Count : 20 times


Prerequisites
The UE is subscribed on the HSS as follows:
QCI = 9 (by default),, ARP = 11, UL and DL AMBRs = 150 Mbit/s
Procedure

Expected Result

1. Power on the UE so that it initiates


the attach procedure.

The UE attaches to CELL1.

2. Wait 10s and verify that UE1 is in idle


mode.

The message RRC Connection Release


indicates that UE1 has entered idle mode.

3. Enable the UE to leave the LTE cell


and approach the UMTS cell until a
reselection is happened
4. Return back moving from the UMTS
towards the LTE Coverage , till
Reselection from UMTS to LTE is
happened
2016-11-25

Huawei Proprietary - Restricted Distribution

Page36, Total37

Document Title

Security Level

5. Repeat Step 2 , 4 & 4 for 20 times


Output :
Time Latency

2016-11-25

Huawei Proprietary - Restricted Distribution

Page37, Total37

Você também pode gostar