Catalog c007b Full

TURNING TOOLS / ROTATING TOOLS / TOOLING SOLUTIONS
2015
2016
C007B
USING THIS CATALOGUE

a This
catalogue is as of April 2015.
a Stock
a
a Please
note that products in this catalogue are

continuously reviewed and updated. The products
therefore may be changed in the future and thus
become different from the catalogue.
status indication
: Inventory maintained.
r : Non stock, produced to order only.

[ : Inventory maintained.
To be replaced by new products.
a Stock
status is mentioned for the products in this

catalogue. However, please note that the products
here may be replaced by new grades and products
in the future.
(Note) Please contact us regarding order numbers and grades

that are not mentioned in this catalogue.
HOW TO USE THIS CATALOGUE

In this catalogue our cutting tools are classified into three
main categories, turning tools, milling tools and drilling tools,
which are arranged according to types of machining. This
helps to find the most suitable products through various
references as follows. Please read the instructions to find the
best products for your purpose.
b How to use the block sections.

A usage guide for each block is shown on the left of each
index (not for all blocks). Refer to this page to know how to
read the product information and how the page is organized.
zTo find the products through the INDEX.

Turning tools are classified by a green colour.
Milling tools are classified by a blue colour.
Main classification
colour.
Drilling tools are classified by a red colour.
For the others, refer to the index on the following page.
TURNING TOOLS
INSERT STANDARDS
INSERT GRADES
INDENTIFICATION .................................................. A002
HOLE GEOMETRY .................................................. A004
PRECISION BREAKER STANDARD ...................... A006
.................................. A009
OUTLINE OF
CLASSIFICATION OF GRADES AND CHIP BREAKERS FOR TURNING ... A010
PRECISION BREAKER SYSTEM ........................... A026
WIPER INSERT........................................................ A028
GRADES FOR TURNING ........................................ A030
TURNING APPLICATION RANGE .......................... A031
COATED CARBIDE (CVD) ...................................... A034
COATED CARBIDE (PVD) ...................................... A036
CERMET .................................................................. A037
COATED CERMET .................................................. A038
CEMENTED CARBIDE ............................................ A039
MICRO-GRAIN CEMENTED CARBIDE .................. A040
CLASSIFICATION OF INSERTS ............................. A042
RECOMMENDED CUTTING CONDITIONS ............ A070
xTo find the series of products from the contents of the

inside title.
Contents of each block are listed on each inside title.
STANDARD OF INSERTS
NEGATIVE INSERTS WITH HOLE
CNppTYPE...RHOMBIC 80 ........... A092
DNppTYPE...RHOMBIC 55 ........... A098
RNppTYPE...ROUND .................. A104
SNppTYPE...SQUARE 90 ............ A105

TN ppTYPE...TRIANGULAR 60 ...... A110
VNppTYPE...RHOMBIC 35 ........... A116
WNppTYPE...TRIGON 80 ............. A119
cTo find the product according to application.

The classification page of each block provides the series
of products to be selected according to applications and
purposes.
NEGATIVE INSERTS WITHOUT HOLE

TNppTYPE...TRIANGULAR 60 ...... A125
POSITIVE INSERTS WITH HOLE
CC ppTYPE...RHOMBIC 80 ........... A126
CPppTYPE...RHOMBIC 80 ........... A131

DC ppTYPE...RHOMBIC 55 ........... A132
DEppTYPE...RHOMBIC 55 ........... A136
RC ppTYPE...ROUND .................. A137
SCppTYPE...SQUARE 90 ............ A138
vAlphabetical index.
All tools are listed in the alphabetical index at the front of
the catalogue.
SP ppTYPE...SQUARE 90 ............ A140

TC ppTYPE...TRIANGULAR 60 ...... A141
TE ppTYPE...TRIANGULAR 60 ...... A144
TP ppTYPE...TRIANGULAR 60 ...... A145
VBppTYPE...RHOMBIC 35 ........... A148
VCppTYPE...RHOMBIC 35 ........... A151
VDppTYPE...RHOMBIC 35 ........... A153
VP ppTYPE...RHOMBIC 35 ........... A154
WBppTYPE...TRIGON 80 ............. A155
WCppTYPE...TRIGON 80 ............. A156
WPppTYPE...TRIGON 80 ............. A157
XCppTYPE...RHOMBIC 25 ........... A158
Section colour.
POSITIVE INSERTS WITHOUT HOLE
RTG TYPE................................. A159

A001
Inside Title for Turning Inserts
a How Text and Index are organized

TYPE INSERTS
WITH HOLE
FY
4
SY
2
1
0
HX
6
5
FH
LP
4
3
RP
2
1
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
MP
0.1
0.3
0.5
Feed (mm/rev)
6
5
4
3
SW
MW
1
0
0.7
0.1
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
Cast Iron (< 350MPa)

8
MM
RM
5
4
3
2
1
0
Cutting Conditions (Guide) :

Heavy Cutting
0.3
RK
Flat Top
0.5
Feed (mm/rev)
4
3
0.5
P
M
K
N
S
: General Cutting
LK
CNMG120404-LK
CNMG120408-LK
CNMG120412-LK
0.4
0.8
a a
1.2
a a
CNMG120404-LS
CNMG120408-LS
0.4
0.8
CNMG09T304-SH
CNMG09T308-SH
CNMG120404-SH
CNMG120408-SH
CNMG120412-SH
CNMG120404-SA
CNMG120408-SA
CNMG120412-SA
0.4
0.8
Steel
Cast Iron
NEW
Heat-resistant Alloy, Titanium Alloy

Coated
Cermet Cermet
RE
(mm)
Carbide
UE6105
UE6110
UE6020 NE
MC6015 W
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
NE
MC5005 NEW
MC5015 W
UC5105
UC5115 NE
MP9005 NEW
MP9015 W
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 NE
MT9015 W
Coated
FH
CNMG120402-FH
CNMG120404-FH
CNMG120408-FH
CNMG120412-FH
0.2
0.4
a [
a [
a a
0.8
a a
CNMG120404-FS
CNMG120408-FS
0.4
0.8
CNMG120404-FY
CNMG120408-FY
0.4
0.8
a a
a a a
1.2
C008
C009
E013
E036
E040
H006
008
Finish Cutting
a
C008
C009
E013
E036
E040
H006
008
Finish Cutting
C008
C009
E013
E036
E040
H006
008
Finish Cutting
FJ
Finish Cutting
PK
CNGG1204V5-FJ
CNGG120401-FJ
CNGG120402-FJ
CNGG120404-FJ
CNGG120408-FJ
CNGG120404-PK
0.05
0.1
a
a
0.2
0.4
0.8
a a
a a
0.4
a
a
CNMG120404-LP
CNMG120408-LP
CNMG120412-LP
0.4
0.8
a a
a a
a a
a a
1.2
a a
a a
Light Cutting
LM
CNMG120404-LM
CNMG120408-LM
CNMG120412-LM
0.4
0.8
a a a
1.2
a a a
a a a
Light Cutting
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
Finish Cutting
LP
C008
C009
E013
E036
E040
H006
008
a a
Light Cutting
Non-ferrous Metal
Order Number
FY
Carbide
Stainless Steel
Shape
FS
Coated
Cermet Cermet
Order Number
: Unstable Cutting
Applicable
Holder Page
Work
Material
: Stable Cutting
RE
(mm)
Shape
0.7
NEW
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
LS
a a
a a
Light Cutting
SH
Light Cutting
SA
SW
a a [ a a
a a
0.8
1.2
a a [ a a
a a
0.4
0.8
a a [ a a
a a [ a a
1.2
a a [ a a
CNMG120404-SW
CNMG120408-SW
CNMG120412-SW
0.4
0.8
a a
a a
a a a
a a
a a
a a a
1.2
a a
CNMG120404-SY
CNMG120408-SY
0.4
0.8
CNMG120404-C
CNMG120408-C
0.4
0.8
CNMG120404-MJ
CNMG120408-MJ
CNMG120412-MJ
CNMG120416-MJ
0.4
0.8
a a
a a
1.2
a a
1.6
a a
CNGG120404-MJ
CNGG120408-MJ
0.4
0.8
a a [ a a
C008
C009
E013
E036
E040
H006
008
a a a
C008
C009
E013
E036
E040
H006
008
Light Cutting
[[
C008
C009
E013
E036
E040
H006
008
[[
Light Cutting
MJ
a a
a a
a a
a a
A092
C008
C009
E013
E036
E040
H006
008
Light Cutting
* Please refer to A028 before using the SW breaker (wiper insert).
=
CHIP BREAKERS
: Inventory maintained in Japan.

[ : Inventory maintained in Japan. To be replaced by new products.
(10 inserts in one case)
a
C008
C009
E013
E036
E040
H006
008
Light Cutting
MJ
Title
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
Light Cutting
(Wiper)
SY
NEG
WITH
HOLE
C008
C009
E013
E036
E040
H006
008
0.4
Light Cutting
Index Product Block
Coated
0.3
Feed (mm/rev)
: Unstable Cutting
Non-ferrous Metal
MK
0.1
: General Cutting
Stainless Steel
Cast Iron
LK
2
0
0.7
: Stable Cutting
Steel
LM
0.1
P
M
K
N
S
TURNING INSERTS
Applicable
Holder Page
Rough Cutting
Stainless Steel (< 200HB)
UE6105
UE6110
UE6020
NE
MC6015 W
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
NE
MC5005 W
NE
MC5015 W
UC5105
UC5115
NE
MP9005 W
NE
MP9015 W
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 NE
MT9015 W
Thickness Corner Radius Chip Breaker

Please refer to page A002.
Size
Medium Cutting
Depth of Cut (mm)
CNMG 12 04 02- FH
Light Cutting
P Carbon Steel Alloy Steel (180280HB) P Carbon Steel Alloy Steel (Wiper) M
Mild Steel
Depth of Cut (mm)
Finish Cutting
Depth of Cut (mm)
CN
Depth of Cut (mm)
NEG
80
CHIP CONTROL RANGE FOR WORK MATERIALS

Depth of Cut (mm)
TURNING INSERTS
TURNING INSERTS [NEGATIVE]
GRADES
IDENTIFICATION
A042
A030
A002
A093
INDEX
2015-2016
ROTATING TOOLS
TURNING TOOLS
INDEX
TURNING INSERTS
A001
CBN & PCD TURNING INSERTS
B001
EXTERNAL TURNING TOOLS
C001
SMALL TOOLS
D001
BORING BARS
E001
GROOVING
F001
THREADING
G001
HSK - T TOOLS
H001
BRAZED TOOLS
I001
SOLID END MILLS
J001
INDEXABLE HEAD END MILLS
J436
ROTATING TOOL INSERTS
K001
INDEXABLE MILLING
L001
TOOLING SYSTEM
M001
DRILLING
N001
SPARE PARTS
P001
TECHNICAL DATA
Q001
PR1
PR2
Available database of cutting tools

(ISO 13399 compliance)
1. What is ISO 13399?
International standard with Cutting tool data representation and exchange.
Cutting tools are required to have parameters up to the world standards like in the regulation of the
database and CAD data. Another purpose of ISO 13399 is to establish smooth data communication
between systems.
2. Purpose
Troublesome conversion with the manufacturers is unnecessary when you have cutting tool data that
complies with ISO 13399. This can then be imported to PLM, CAM, CAM, CNC, or even as a tool
management system.
Mitsubishi Materials offers cutting tool data based on ISO 13399 to support effectively improved quality
and cost reduction efficiency in your improved threading and new products creation.
3. Dimension symbols conforming to ISO 13399

As shown below, new dimension symbols complying with ISO 13399.
Examples of change in dimensions

Previous
New
RE
S1
95
LH
L1
45
DAH
DCCB
DC
DCX
*Note 1 See pages 5 to 6 for details.

PR3
L3
L2
L1
45
DCON
LF
140
DC
D4
140
D1
PL
v Solid Drills
L8
LCCB
L7
L1
D8
*D
D1
D2
ap
*L
c Milling Cutter
BD
DCON
KWW
L8
D12
D9
W1
LF
CBDP
LF
95
L2
F1
x Holder
IC
80
WF
D1
80
APMX
z Inserts
D1
D2
Re
LCF
LH
OAL
4. CAD (ISO13399 compliance)

As shown below, DXF (2 dimensions) and STEP (3 dimensions) data complying with ISO 13399 are
updated regularly to the Web CATALOG.
zDXF
(Full layer)
xDXF
(CUT/NO CUT layer)
Ex. IMX10C4HV100R05010
cSTEP data (details, insert assembled model)
vSTEP data (simple model)
PCS
MCS
Y
Z
CIP
2 Download and refer to the "Web CATALOGUE" of PR17

*Note
Note 3 CAD is updated regularly. However, in rare cases, it may not be possible to provide the desired product.
*
Please consult us.
PR4
Dimensions and symbols (ISO 13399 compliance)

Alphabetical
z Inserts
Symbol
AN
AS
BCH
BS
CDX
CF
CW
D1
DC
DCON
DMIN
DMM
EDR
EPSR
FHCSA
FHCSD
GAN
IC
INSL
KAPR
KRINS
L
LBB
LE
LF
LU
M
PDPT
PDX
PDY
PNA
PSIRL
PSIRR
RAL
RAR
RE
S
W1
x Turning
Content
Clearance angle major
Clearance angle wiper edge
Corner chamfer length
Wiper edge length
Maximum groove depth
Blade tip
Cutting width
Fixing hole diameter
Cutting diameter
Fixing part diameter
Minimum cutting diameter
Shank diameter
Radius honing
Insert included angle
Fixing hole countersunk angle
Fixing hole diameter top
Insert rake angle
Inscribed circle
Insert length
Tool cutting edge angle
Cutting edge angle major
Cutting edge length
Breaker width
Cutting edge effective length
Cutting Edge, Length
Usable length
m-dimension
Overhang
Profile distance X
Profile distance Y
Profile included angle
Cutting edge angle major left hand
Cutting edge angle major right hand
Relief angle left hand
Relief angle right hand
Corner radius
Thickness
Insert width
Symbol
Content
B
CDX
CUTDIA
DAXN
DAXX
DCB
DCON
DMIN
DMM
GAMF
H
HBH
HBKW
HF
HTB
KAPR
LB
LDRED
LF
LH
LU
OAH
OAL
OAW
PSIR
WF
Shank width
Maximum groove depth
Maximum cut off diameter
Axial groove outside diameter minimum
Axial groove outside diameter maximum
Fixing part depth
Min. Cutting Diameter
Shank diameter
Rake angle normal
Shank height
Head bottom offset height
Head back offset width
Functional height
Body height
Cutting edge angle
Body length
Neck length
Functional length
Head length
Usable length
Overall height
Overall length
Overall width
Lead angle
Functional width
1 This symbol complies with TS standard or DTS standard of ISO 13399.

*Note
Note 2 The above does not include the unset symbols or original Mitsubishi Materials symbols of ISO 13399.
*Note 3 Changes and additions may be made because the table above also includes symbols under deliberation.
*
PR5
c Milling
v Drilling
Symbol
Content
Symbol
Content
APMX
AZ
BD
BHTA
CBDP
CRKS
DAH
DBC
DC
DCB
DCCB
DCON
DCON_MS
DCON_WS
DCX
DHUB
DMM
GAMF
GAMP
KAPR
KWW
LCCB
LE
LF
LH
LPCON
LU
LUX
OAL
PRFRAD
PSIR
RMPX
WT
ZEFP
Max. depth of cut

Plunge depth maximum
Body diameter
Neck taper half angle
Connection bore depth
Connection retention knob thread size
Diameter access hole
Diameter bolt circle
Cutting diameter
Fixing bolt seat diameter
Fixing part depth
Contact surface diameter machine side
Contact surface diameter workpiece side
Maximum hole diameter
Contact surface diameter
Shank diameter
Rake angle radial
Rake angle axial
Tool cutting edge angle
Keyway width
Fixing bolt seat thickness
Cutting edge effective length
Functional length
Neck length
Overall head length
Cutting edge length
Maximum neck length
Overall length
Profile radius
Lead angle
Ramping angle
Weight of item
Peripheral effective cutting edge count
BD
CDN
CNT
CRKS
CZC
DC
DCSFMS
DCON
DMM
LCF
LF
LH
LPR
LU
OAL
PL
SDL
ZEFP
Body diameter
Front oil filling hole diameter
Rear oil filling hole diameter
Connection size code
Cutting diameter
Flange diameter
Fixing part depth
Shank diameter
Length chip flute
Functional length
Neck length
Protruding length
Usable length
Overall length
Point length
Step diameter length
Peripheral effective cutting edge count
b Others
Symbol
Content
ASP
BD
CRKS
CZC
DBC
DC
DCB
DCON
DCON_MS
DCON_WS
DF
DMM
FLGT
HF
KWW
LB
LF
LP
LPR
LS
LSCX
LU
MHA
MHD
MHH
OAL
RE
RPMX
Adjusting screw protrusion

Body diameter
Taper size
Diameter bolt circle
Cutting diameter
Fixing part diameter
Contact surface diameter machine side
Contact surface diameter workpiece side
Flange outer diameter
Shank diameter
Flange diameter
Fixing seat dimension
Keyway width
Body length
Functional length
Overhang
Distance from end of collar
Shank length
Clamping length maximum
Usable length
Mounting hole angle
Mounting hole distance
Mounting hole height
Overall length
Corner radius
Ramping angle
PR6
NEW PRODUCTS
What is MIRACLE SIGMA?

1. Next-generation PVD
2. PVD coating technology
3. Shape maintainability
Long life & high quality

High efficiency
Improved productivity
and cost reduction
PVD coating and its peripheral technology displays the performance of new generation miracle
coating and shape maintainability giving you the MIRACLE SIGMA.
Highest efficiency offers further productivity and cost cutting.
The following is an example.
ZERO-
The unique ZERO- Surface achieved an
unique coating.
Extremely smooth and dense surface.
Sharp cutting edges with low friction
coefficient.
SMART MIRACLE
coating
Conventional cutting
edge
TOUGH-
INNOVATIVE PVD COATING TECHNOLOGY
Extremely tough, smooth and wear resistant for
high productivity milling.
*Laminated coating (image)
PR7
Hardness (HV)
Al-rich (Al,Ti) N
Al-rich
New Technology
High aluminium
particle content
Al-rich (Al,Ti) N
New Al-rich (Al, Ti)N with increased Al content
improves film hardness and stabilizes the
hardness aspect. Additionally, resistance to
wear,abrasion and welding are drastically
improved in turning to high heat resistance
alloy.
Aluminium (%)
TRI-cooling
Technology
Unique coolant hole shape improves flow and
stabilizes the high hardness aspect (more than
6) to offer the longer-life.
Unique insert minimizes

chatter and vibration
Z Insert Geometry
provides lower cutting
resistance
Double
Geometry
Double sided Z Geometry
Mitsubishi Materials proprietary double sided,

Z Geometry insert features a sharp cutting edge
with low cutting resistance by utilizing features
from both conventionally positive and negative
rake inserts.
*NOTE 1. MIRACLE SIGMA products are not given the
mark.
PR8
NEW PRODUCTS
L010
Low cutting resistance and double sided insert

face mill for general machining
WSX445
Unique geometry minimizes
chatter and vibration!
Mitsubishi Materials proprietary double sided, Z Geometry insert features a sharp
cutting edge with low cutting resistance by utilizing features from both conventionally
positive and negative rake inserts.
Double
Geometry
BREAKER SYSTEM
Breaker series for varied depths of cut and feeds
Focus on
cutting edge
sharpness
Stable Cutting (Continuous cutting, Without scale, etc.)
breaker
L
The high rake angle boosts
cutting performance. Positive
land retains strength and
provides low cutting resistance.
PR9
Mbreaker
First recommendation for

general applications. A good
balance of edge strength and
sharpness is provided by the
optimized positive land and rake
angle.
Unstable Cutting (Interrupted cutting, With scale, etc.)
Rbreaker
For unstable applications.

Enhanced edge strength
and retention of sharpness
is provided by the negative
land and positive rake angle
respectively.
Focus on
cutting edge
strength
Hbreaker
For demanding applications.

A stronger land and reduced
positive rake angle provides
maximum edge strength.
INSERT GRADE FOR A WIDE RANGE OF MATERIALS
Application range
Application range
PVD
VP15TF
H H10
N40
VP15TF
K40
N N10
N30
MC5020
K30
ISO
Cemented carbide
PVD
VP20RT
Cast Iron
VP20RT
VP15TF
MP7130
Stainless Steel
K20
Hardened Materials
S40
M40
N20
Application range
CVD
K K10
TF15
S30
M30
ISO
PVD
Non-Ferrous Metal
S20
M20
ISO
PVD
VP20RT
S10
Application range
VP15TF
Heat Resistant Alloy Ti Alloy
VP20RT
P40
MP9120
Steel
P30
ISO
Application range
M M10
MP6130
P20
ISO
PVD
VP15TF
P P10
Application range
MP6120
ISO
H20
H30
H40
CUTTING RESISTANCE
WSX445s low cutting resistance equals to that of single sided insert cutters.The low axial and radial
forces reduce vibrations to a minimum.
[Comparison of the back force]

800
40%
Lower cutting
resistance
Cutting resistance (N)
600
WSX445
Back Force
M breaker
Conventional insert
Principal Force
400
200
Negative
(Double sided)
WSX445
<Cutting condition>
Work material : SCM440
Cutter Dia.
: 125 mm
Cutting speed : 200 m/min
Feed per tooth : 0.2 mm/tooth
Depth of cut
: ap=4.0 mm
ae=100 mm
Coolant
: Dry cutting,
Single insert
Feed Force
<Back force>
Cutting force in the axial direction.
Back force can cause inaccuracy
and vibration, resulting in
deflection of the work piece as
well as cutting tools.
CHIP DISCHARGE EFFECT

Chips are discharged outwardly because of the negative/positive edge design.
This helps prevent jamming of continuous chips also damage to the coolant holes.
WSX445
Conventional negative insert A Conventional negative insert B
<Cutting condition>
Work material : SCM440
Cutting speed : 150m/min
Feed per tooth : 0.2mm/tooth
Depth of cut
: ap=4mm
ae=100mm
Coolant
: Dry cutting
The chips generated are helical
and discharged outwardly.
Chips can be discharged inwardly

and can cause problems.
PR10
NEW PRODUCTS
A034
ISO Turning Inserts for Steels
MC6015
MC6025
LP
MP
RP
Opening of a new high efficiency in steel.

Ultra-thick film nano texture TOUGH grip
and 2 in 1 technology realize long life without
regret to high-speed cutting.
Combination with new breaker vastly increases efficiency!
P10
P20
P30
For General Steel

Medium
Light
Rough
MC6025
P01
APPLICATION RANGE
MC6015
ISO USE
CLASSIFICATION
SYMBOLS
P40
RP
MP
LP
A035
ISO Turning Inserts for Cast Iron
MC5005
MC5015
LK
MK
RK
Reduced cycle time and cost!

High efficiency examples exceeding 600m/min
cutting velocity appearing one after the other through the
use of ultra-thick film nano texture, TOUGH grip technology.
Line up of new breakers selected by load conditions.
K10
K20
K30
PR11
K40
For cast iron
Medium
MC5015
K01
APPLICATION RANGE
MC5005
ISO USE
CLASSIFICATION
SYMBOLS
Light
Rough
MK
RK
LK
ISO Turning Inserts for Stainless Steel
MC7015
MC7025
MP7035
LM
MM
RM
Stainless steel turning revolution!

New ultra-hard substrate realizes long life at
high deformation resistance by controlling
boundary wear and burrs.
New breaker with sharpness and strength.
ISO USE
CLASSIFICATION
SYMBOLS
M30
M40
Light
Rough
MP7035
M20
Medium
MC7025
M10
MC7015
M01
For Stainless Steel
APPLICATION RANGE
RM
MM
LM
A036
LS
MS
RS
MP9005
MP9015
MT9015
Cutting edge boundary fracturing and chipping

of high heat resistance alloy turning completely
solved!
Al-rich (Al,Ti)N coating realizes improved film
hardness and stable high hardness aspect.
ISO USE
CLASSIFICATION
SYMBOLS
S20
MT9015
S10
Medium
MP9015
S01
For Super Alloy
APPLICATION RANGE
MP9005
ISO Turning Inserts for Difficult-to-Cut Materials
Light
Rough
S30
MS
S40
RS
LS
PR12
NEW PRODUCTS
B004
Coated CBN Grade for High Hardened Steel Turning
BC8110
New Generation Coating Technology.

Excellent wear resistance provides
increased efficiency when turning
hardened steels.
The newly developed Ultra Micro-particle
Binder prevents sudden fracturing.
Cutting resistance
Conventional
Cutting resistance
Ultra Micro-particle Binder
BC8110
Newly developed special ceramic coating

Fusion suppression
TiAlSiN Coating
CBN sintered body

TiAlN Coating
F004
Grooving System
GY
Series
Grooving Revolution
Innovative clamping system ensures
reliable grooving.
Application expanded
Highly reliable insert clamping
Convex
contact face
PR13
J436
Exchangeable Head End Mills
iMX Endmill Series

Carbide + Carbide Double face contact
with head type expands the application
possibilities.
Rigidity near that of a solid tool secured by
ultra-hardening of all head and holder clamping surfaces.
Varied head replacement is associated with
high efficiency.
Cemented carbide
Steel
Steel
Cemented carbide
J026
Vibration Control End Mills for Machining Difficult-to-Cut Materials
SMART MIRACLE
Revolutionary performance for

difficult-to-cut materials.
Application to a wide range of cutting
by series addition.
ZERO- Surface
ZERO- Surface
SMART MIRACLE coating
Conventional
PR14
NEW PRODUCTS
J024
Carbide End Mills
MS plus
High precision end mills with excellent

wear resistance for general machining.
Applicable to finish cutting by improved edge
sharpness cutting edge shape.
MS plus
End cutting edge shape
Regular cutting path
Conventional
Unclear cutting path
J314
Corner Radius End mill for High Efficiency Machining Series
VFFDRB
High hardness and high efficiency

machining realized
Thin cuttings
Thin cuttings and a long cutting edge

combine for high performance and long life.
VFFDRB
Conventional
Reduced cutting
resistance in the radial
direction suppresses
tool vibration and
deflection.
Large
radius
PR15
Small
radius
Small
Large
N012
Carbide Solid Drills
WSTAR Drill Series
MVE/MVS
PVD coating provides long tool life for

a wide range of applications.
TRI-cooling Technology
On drills over 6mm
Coolant flow speed

increases
Velocity (m/s)
MVS
Coolant hole
60.000
48.000
36.000
24.000
12.000
Groove
0.0000
Cutting edge
Velocity (m/s)
Conventional
60.000
Coolant hole
48.000
36.000
24.000
Groove
12.000
0.0000
Cutting edge
N212
Indexable Drill
MVX
High rigidity body produced by

utilizing the cutting-edge technology.
Economical 4-corner insert.
Ideal combination of outer CVD insert and

inner PVD insert.
All-round UM breaker
US breaker for
Stainless Steel
PR16
Mitsubishi Material Web catalogue
Web CATALOGUE
Language: Japanese, English, Chinese, Brazilian Portuguese

1
1 Enhanced search
function!
Optimum tool can be selected from cutting
mode, work, and cutting conditions as well
as item number.
3 4
2 Tooling sheet mounting

"Simple registration in tooling
sheet by pressing a button. Cutting time and
operation time can be calculated in no time
at all"
3 Favorite registration
function
Favorite product can be registered.
4 Youtube
Product screen can be viewed.
5 Excel & image data
download
Product image and dimensional drawings
as well as product information data (excel)
can also be downloaded.
6 ISO 13399 compatible CAD data updated regularly!

ISO 13399 compliance DXF/STEP (simple/detailed) data can be downloaded.
3D simple model (STEP) example
3D detailed model (STEP) example
+
is updated regularly. However, in rare cases, it may not be possible to provide the desired product.
*CAD
Please consult us.
Access the Web catalog here.

http://www.mitsubishicarbide.net
PR17
e-Learning system
Mitsubishi Materials EXPERT program
You can study cutting technology.
http://mmc-permanent.learnways.com
Language: Japanese, English
http://www.mitsubishicarbide.com
To selection screen of each cutting
technology course without the need for
registration.
Can participate in milling, turning,

drilling, and other courses for free.
aCan select English/Japanese
Can participate even with tablet

PC and smart phone for free.
PR18
Memo
INDEX
INDEX FOR TOOL NUMBER
A ........................................... 2
B ........................................... 2
C ........................................... 3
D ........................................... 5
E ........................................... 6
F ........................................... 6
G ........................................... 7
H ........................................... 7
I ........................................... 8
J ........................................... 8
K ........................................... 8
L ........................................... 8
M ........................................... 8
N ........................................... 9
O .......................................... 10
P .......................................... 10
Q .......................................... 11
R .......................................... 11
S .......................................... 11
T .......................................... 13
U .......................................... 14
V .......................................... 15
W.......................................... 16
X .......................................... 17
Z .......................................... 17
NUMBER OTHERS........... 17
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
APX4000RooooooA.............APX4000 type face mill................................L053

APX4000Rooo MooAoo.......APX4000 type end mill.................................L054
Aooo -DCLNR/L12...................DOUBLE CLAMP DIMPLE BAR................. E013 APX4000Rooo SAoooA........APX4000 type end mill.................................L052
Aooo -DDUNR/L15...................DOUBLE CLAMP DIMPLE BAR................. E013 APX4K-oooAooAooo RA....APX4000 type end mill (Long cutting edge).........
Aooo -DSKNR/L12...................DOUBLE CLAMP DIMPLE BAR................. E014
L058
Aooo -DTFNR/L16...................DOUBLE CLAMP DIMPLE BAR................. E014 APX4KR06316CA056A.............APX4000 type end mill (Long cutting edge).........
Aooo -DVUNR/L16...................DOUBLE CLAMP DIMPLE BAR................. E015
L058
Aooo -DWLNR/Loo................DOUBLE CLAMP DIMPLE BAR................. E015 APX4KRoooo SA42S056A.....APX4000 type end mill (Long cutting edge).........
Aooo PCLNR/Loo...................P type boring bar................................ E036,P024
L058
Aooo PDQNR/Loo..................P type boring bar......................................... E037 APX4KRooooWA508ooooA....APX4000 type end mill (Long cutting edge).........
Aooo PDUNR/Loo..................P type boring bar......................................... E036
L058
Aooo PDZNR/Loo...................P type boring bar......................................... E038 AQXRooo MooAoo...............AQX type end mill.........................................L078
Aooo PSKNR/Loo..................P type boring bar................................ E035,P024 AQXRooo SA/Noo S/L............AQX type end mill................................L076,L077
Aooo PTFNR/Loo...................P type boring bar......................................... E035 ARXoo Rooo MooA30...........ARX type end mill................................L099,L101
Aooo PWLNR/Loo..................P type boring bar......................................... E037 ARXoo Rooo SAoo S/LW.......ARX type end mill.......................L098,L099,L101
ABSooo -ES-M.........................Parts for ABS head......................................M020 ASSo.........................................Spring (For AJX/BRE/CV type cutter)..................
C030,L084 L088,P031,P032
ABSooo -ES-Mo......................Parts for ABS head............................M020,M021
ABSooo -FS-W.........................Parts for ABS adapter.................................M019 ASX400-oooooo R.................ASX400 type face mill.........................L040,L041
ABSooo M................................Parts for ABS head......................................M020 ASX400Roooooo..................ASX400 type face mill..................................L040
ABSoooW................................Parts for ABS adapter.................................M019 ASX400RoooAM16oo...........ASX400 type end mill...................................L042
ABSoo -Fo................................Screw (For ABS adapter)............................M019 ASX400Rooo Soo..................ASX400 type end mill...................................L042
AEMWoooooo ER.................Insert (For BAE type cutter)......................... K023 ASX445-oooooo R.................ASX445 type face mill.........................L018,L019
AF5000 type..............................AF5000 type face mill.................................. P027 ASX445Roooooo..................ASX445 type face mill..................................L018
AHX640S-ooooooo R/L........AHX640S type face mill.......................L026,L027 ASX445Rooo Soo..................ASX445 type end mill...................................L020
AHX640SR/Looooooo.........AHX640S type face mill................................L026 AXD4000-oooAoo RA/B.........AXD4000 type face mill................................L061
AHX640W-oooooo R/L..........AHX640W type face mill...............................L031 AXD4000RooooooA/B..........AXD4000 type face mill................................L061
AHX640WR/Loooooo...........AHX640W type face mill...............................L030 AXD4000Rooo SAoooo........AXD4000 type end mill.................................L060
AJSooooToo.........................Clamp screw (For AJX type cutter)............. P003 AXD7000-oooAoo RA/B.........AXD7000 type face mill.......................L066,L067
AJXoo -ooooooo.................AJX type face mill.......................L084,L085,L091 AXD7000RooooooA/B..........AXD7000 type face mill................................L066
AJXoo Rooooo.....................AJX type face mill................................L084,L091 AXD7000RoooooA-H63A......AXD7000 type end mill.................................L067
AJXoo RoooAMoooo..........AJX type end mill..........................................L088 AXD7000Rooo SAoo SA/B.....AXD7000 type end mill.................................L066
AJXoo Rooo SAoo S/SS/L/EL....AJX type end mill.................................L086,L087
AMSo.........................................Clamp bridge............................................... P014
AOGT1236oo PEFR-GM...........Insert (For APX3000 type cutter)........ K022,L049 B1oooo...................................Arbor (D type boring head)....... E041,F132,G033
AOMT1236oo PEER-o.............Insert (For APX3000 type end mill).... K022,L049 BAE type...................................BAE type end mill........................................ P031
AOMT1848oo PEER-o.............Insert (For APX4000 type end mill).... K022,L055 BAP300Roooo ESoo.............BAP300 type end mill (Long cutting edge)....L156
AOX445-oooooo R................AOX445 type face mill..................................L032 BAP300Rooo LSoo................BAP300 type end mill (Long shank type).....L153
AOX445Roooooo..................AOX445 type end mill...................................L032 BAP300Rooo Soo..................BAP300 type end mill...................................L153
APGT1135PDFR-G2..................Insert (For BAP300 type cutter)............................ BAP300 type.............................BAP300 type face mill................................. P027
K022,L154,L156 BAP400-oooAoo R.................BAP400 type face mill................................. P027
APGT1604PDFR-G2..................Insert (For BAP400 type cutter)................... K023 BAP400Rooooo.....................BAP400 type face mill................................. P027
APMT1135PDER-Ho.................Insert (For BAP300/SRM2 type cutter)................. BAP400Roooooooo............BAP400 type end mill (Long cutting edge).... P031
K023,L129,L154,L156 BAP400Rooo Soo..................BAP400 type end mill.................................. P031
APMT1135PDER-Mo................Insert (For BAP300/SRM2 type cutter)................. BCo...........................................Clamp set (For BC type cartridge/FCDG4 type boring bar)....
K023,L129,L154,L156
M005,P025
APMT1604PDER-Ho.................Insert (For BAP400/SRM2 type cutter)................. BCoo.........................................Clamp set (For BC type cartridge)...............M005
K023,L129,L134 BCPooo...................................Shim pin...................................................... P013
APMT1604PDER-M2.................Insert (For BAP400/SRM2 type cutter)................. BF407Rooooo........................BF407 type face mill.................................... P027
K023,L129,L134 BF-CCGToooooooo2..........Insert (Class G tolerance)........................... B040
APX3000-oooAoo RA............APX3000 type face mill................................L047 BF-CNGGooooooTA4..........Insert (Class G tolerance)........................... B022
APX3000RooooooA.............APX3000 type face mill.......................L046,L047 BF-CNGMoooooooo2.........Insert (Class G tolerance)........................... B024
APX3000Rooo MooAoo.......APX3000 type end mill.................................L048 BF-DCGToooooooo2..........Insert (Class G tolerance)........................... B044
APX3000Rooo SAoooA........APX3000 type end mill.................................L046 BF-DNGGooooooTA4..........Insert (Class G tolerance)........................... B025
APX4000-oooAoo RA............APX4000 type face mill................................L053 BF-DNGMoooooooo2.........Insert (Class G tolerance)........................... B027
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
BM-CNGMooooooTA2.........Insert (Class G tolerance)........................... B024 Cooo SVQCRoo.....................S type boring bar (Carbide shank).............. E032
BM-DNGMooooooTA2.........Insert (Class G tolerance)........................... B027 Cooo SVUCR/Loo..................S type boring bar (Carbide shank).............. P023
BM-TNGMooooooTA3..........Insert (Class G tolerance)........................... B031 Cooo SWUBRoo.....................MICRO-DEX boring bar (Carbide shank).... E016
BN425 type................................BN425 type face mill................................... P027 C2JS..........................................Carbide end mill........................................... J095
BOESooo.................................Set bolt (For OCTACUT type cutter)........... P009 C2LA..........................................Carbide end mill........................................... J100
BOE type...................................BOE type face mill....................................... P027 C2LS..........................................Carbide end mill........................................... J096
BOE type...................................BOE type end mill........................................ P031 C2MA.........................................Carbide end mill........................................... J098
BPT322......................................Shim............................................................ P010 C2MB.........................................Carbide end mill........................................... J269
BRAoooo Soo........................BRA type drill............................................... N206 C2MHA.......................................Carbide end mill........................................... J104
BRBoooo Soo M.....................BRB type drill............................................... N205 C2MS.........................................Carbide end mill........................................... J092
BRE type...................................BRE type end mill........................................ P031 C2SA..........................................Carbide end mill........................................... J102
BRLoooo Soo........................BRL type drill............................................... N208 C2SS..........................................Carbide end mill........................................... J091
BRMoooo Soo.......................BRM type drill.............................................. N202 C3SA..........................................Carbide end mill........................................... J124
BRMBoooo Soo.....................BRMB type drill............................................ N204 C3SARB.....................................Carbide end mill........................................... J304
BRPoo Rooo ELSoo..............BRP type end mill.........................................L102 C4JC..........................................Carbide end mill........................................... J174
BRPoo Rooo LSoo................BRP type end mill.........................................L102 C4LC..........................................Carbide end mill........................................... J175
BRPoo Rooo Soo..................BRP type end mill.........................................L102 C4MC.........................................Carbide end mill........................................... J173
BRPo Pooooooo..................BRP type face mill........................................L103 CAooo......................................Clamp bridge............................................... P014
BRPo P-oooAoo R.................BRP type face mill........................................L104 CAS51T......................................Set screw..................................................... P003
BRSooo...................................Wedge screw .............................................. P003 CBoo RS...................................MICRO-MINI TWIN..................................... E019
BRSoooo Soo........................BRS type drill............................................... N200 CBoo RS-B................................MICRO-MINI TWIN..................................... E019
BRSBoooo Soo.....................BRSB type drill............................................ N204 CBJPRooo Soo......................CBJP type end mill.......................................L137
BSX400 type..............................BSX400 type face mill................................. P028 CBMPRooo Soo.....................CBMP type end mill......................................L137
BSX500 type..............................BSX500 type face mill................................. P028 CBN2XLB...................................CBN end mill................................................ J267
BSX type....................................BSX type end mill........................................ P031 CBN2XLRB................................CBN end mill................................................ J302
BTAHR/Loooo -50...................Small tools holder (External back turning).... D012 CBSoo......................................Breaker piece.............................................. P016
BTAToooooo R/L-B...............Insert for external back turning.................... D012 CBToo......................................Breaker piece.............................................. P016
BTAT605000RX.........................Insert for external back turning.................... D012 CBToooo................................Breaker piece.............................................. P016
BTBToooooo R/L..................Insert for external back turning.................... D013 CCEToooooo R/L-SN............Insert (Class E tolerance)............................ A129
BTBToooooo R/L-B...............Insert for external back turning.................... D013 CCEToooooo R/L-SR............Insert (Class E tolerance)............................ A129
BTVHRoooo -oo....................Small tools holder (External back turning).... D014 CCEToooooo R/LW-SN.........Insert (Class E tolerance)............................ A130
BTVToooooo R-B..................Insert for external back turning.................... D014 CCGHoooooo R/L-F..............Insert (Class G tolerance)........................... A127
BXD4000-oooooo RA/B........BXD4000 type face mill.......................L072,L073 CCGToooooo -AZ..................Insert (Class G tolerance)........................... A126
BXD4000RooooooA/B..........BXD4000 type face mill................................L072 CCGToooooo -FJ..................Insert (Class G tolerance)........................... A126
BXD4000Rooo SAoo ELA/ELB....BXD4000 type end mill.................................L074 CCGToooooo L-F..................Insert (Class G tolerance)........................... A127
BXD4000Rooo SAoo SA/SB....BXD4000 type end mill.................................L074 CCGToooooo M-SMG...........Insert (Class G tolerance)........................... A130
BXD4001Rooo SAoo ELA/ELB....BXD4000 type end mill.................................L074 CCGToooooo R/L-SN............Insert (Class G tolerance)........................... A130
BXD7000 type...........................BXD7000 type face mill............................... P028 CCGToooooo R/L-SS............Insert (Class G tolerance)........................... A127
BXD7000 type...........................BXD4000 type end mill................................ P032 CCGWoooooo.......................Insert (Class G tolerance)........................... A130
BZC400 type..............................BZC400 type face mill................................. P028 CCGWoooooo FS..................Insert (Class G tolerance)........................... B041
BZC400 type..............................BZC400 type end mill.................................. P032 CCKoo......................................Clamp bridge............................................... P014
CCMHoooooo -MV................Insert (Class M tolerance)........................... A128

CCMHoooooo -SV.................Insert (Class M tolerance)........................... A127
Cooo R-BLS.............................MICRO-MINI boring bar (Solid carbide)............... CCMToooooo........................Insert (Class M tolerance)........................... A128
E022,F125 CCMToooooo -FM.................Insert (Class M tolerance)........................... A126
Cooo SCLCR/Loo...................S type boring bar/MICRO-MINI (Carbide shank).... CCMToooooo -FP..................Insert (Class M tolerance)........................... A126
E016,E030,P023 CCMToooooo -FV..................Insert (Class M tolerance)........................... A126
Cooo SCZCR/Loo...................S type boring bar (Carbide shank).............. P023 CCMToooooo -LM.................Insert (Class M tolerance)........................... A127
Cooo SDQCRoo.....................S type boring bar (Carbide shank).............. E031 CCMToooooo -LP..................Insert (Class M tolerance)........................... A127
Cooo SDUCR/Loo..................S type boring bar (Carbide shank)..... E029,P023 CCMToooooo -MK.................Insert (Class M tolerance)........................... A128
Cooo SDZCR/Loo...................S type boring bar (Carbide shank).............. P023 CCMToooooo -MM................Insert (Class M tolerance)........................... A128
Cooo SSKCR/Loo..................S type boring bar (Carbide shank).............. P023 CCMToooooo -MP.................Insert (Class M tolerance)........................... A128
Cooo STFCRoo......................S type boring bar (Carbide shank).............. E028 CCMToooooo -MW................Insert (Class M tolerance)........................... A129
Cooo STUCR06........................MICRO-DEX boring bar (Carbide shank).... E017 CCMToooooo -SW................Insert (Class M tolerance)........................... A127
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
CCMWoooooo......................Insert (Class M tolerance).........A130,B041,B059 CPMHoooooo -FV.................Insert (Class M tolerance)........................... A131

CCMXoooooo EN-A..............Insert (For DCCC type end mill).................. K023 CPMHoooooo -MV.................Insert (Class M tolerance)........................... A131
CCMX09T308EN-B....................Insert (For DCCC type end mill).................. K024 CPMHoooooo R/L-F..............Insert (Class M tolerance)........................... A131
CCPoo......................................Shim pin...................................................... P013 CPMHoooooo -SV.................Insert (Class M tolerance)........................... A131
CCTC1........................................Clamp bridge............................................... P014 CPMTooooZPEN-Mo.............Insert (For PMR type end mill)........... K024,L143
CESPRooo Soo......................CESP type end mill......................................L113 CPMXoooooo........................Insert (Class M tolerance)........................... A131
CFMooooo.............................Shim screw.................................................. P021 CRo...........................................Stop ring..........................G013,H016,P021,P025
CFSPRooo Soo......................CFSP type end mill.......................................L113 CRoo RS-01..............................MICRO-MINI TWIN..................................... E020
CGoo RS-ooo.........................MICRO-MINI TWIN......................................F126 CRoo RS-01B............................MICRO-MINI TWIN..................................... E020
CGSPRooo Soo......................CGSP type end mill......................................L113 CRN2MB....................................CRN end mill................................................ J254
CKooo......................................Clamp bridge............................................... P014 CRN2MRB..................................CRN end mill................................................ J298
CKW6.........................................Clamp bridge............................................... P015 CRN2MS....................................CRN end mill................................................ J081
CMH...........................................Carbide end mill........................................... J123 CRN2XL.....................................CRN end mill................................................ J083
CMRA.........................................Carbide end mill........................................... J195 CRN2XLB...................................CRN end mill................................................ J256
CNGAoooooo.......................Insert (Class G tolerance)........................... B024 CRN2XLRB................................CRN end mill................................................ J300
CNGGoooooo -FJ..................Insert (Class G tolerance)........................... A092 CRN4JC.....................................CRN end mill................................................ J166
CNGGoooooo -MJ.................Insert (Class G tolerance)........................... A093 CSo............................................Clamp screw................................................ P003
CNGGoooooo -PK.................Insert (Class G tolerance)........................... A092 CSoo.........................................Shim............................................................ P010
CNGNoooooo.......................Insert (Class G tolerance)........................... B035 CSooooooT...........................Clamp screw................................................ P003
CNMAoooooo.......................Insert (Class M tolerance).........A097,B024,B055 CSAFoo....................................Stop screw................................................... P029
CNMGoooooo.......................Insert (Class M tolerance)........................... A095 CSBPR/Loooo........................MC holder.................................................... P018
CNMGoooooo -C...................Insert (Class M tolerance)........................... A093 CSF401260T..............................Clamp screw................................................ P003
CNMGoooooo -FH.................Insert (Class M tolerance)........................... A092 CSKPR/Loooo........................MC holder.................................................... P018
CNMGoooooo -FS.................Insert (Class M tolerance)........................... A092 CSKPRoo CAoo......................BC type cartridge.........................................M004
CNMGoooooo -FY.................Insert (Class M tolerance)........................... A092 CSRA.........................................Carbide end mill........................................... J193
CNMGoooooo -GH................Insert (Class M tolerance)........................... A097 CSRARB....................................Carbide end mill........................................... J306
CNMGoooooo -GJ.................Insert (Class M tolerance)........................... A097 CSSNR/Looooooo...............MC holder.................................................... P018
CNMGoooooo -GK................Insert (Class M tolerance)........................... A094 CSSPR/Loooo........................MC holder.................................................... P018
CNMGoooooo -GM................Insert (Class M tolerance)........................... A094 CSSPRoo CAoo......................BC type cartridge.........................................M004
CNMGoooooo -LK.................Insert (Class M tolerance)........................... A093 CSTNR/Looooooo...............MC holder.................................................... P018
CNMGoooooo -LM................Insert (Class M tolerance)........................... A092 CSVHR/Loooo........................Small tools holder (For cam tool posts)....... D027
CNMGoooooo -LP.................Insert (Class M tolerance)........................... A092 CSVTBooo R/L.........................Insert for external back turning.................... D028
CNMGoooooo -LS.................Insert (Class M tolerance)........................... A093 CSVTBooo R-B........................Insert for external back turning.................... D028
CNMGoooooo -MA................Insert (Class M tolerance)........................... A095 CSVTBXL...................................Insert for external back turning.................... D028
CNMGoooooo -MH................Insert (Class M tolerance)........................... A095 CSVTCoooo R/L......................Insert for external cutting off........................ D028
CNMGoooooo -MJ.................Insert (Class M tolerance)........................... A093 CSVTCoooo R-B.....................Insert for external cutting off........................ D028
CNMGoooooo -MK................Insert (Class M tolerance)........................... A094 CSVTFooo R/L.........................Insert for external front turning.................... D027
CNMGoooooo -MM................Insert (Class M tolerance)........................... A094 CSVTFooo R/L-B.....................Insert for external front turning.................... D027
CNMGoooooo -MP................Insert (Class M tolerance)........................... A094 CSVTFXL...................................Insert for external front turning, Copying..... D027
CNMGoooooo -MS................Insert (Class M tolerance)........................... A095 CSVTGooooo R/L...................Insert for grooving....................................... D029
CNMGoooooo -MW...............Insert (Class M tolerance)........................... A095 CSVTTooooo RR/L.................Insert for threading...................................... D029
CNMGoooooo -RK................Insert (Class M tolerance)........................... A096 CToo.........................................Shim............................................................ P010
CNMGoooooo -RM................Insert (Class M tolerance)........................... A096 CToo RS-Moo..........................MICRO-MINI TWIN..................................... G026
CNMGoooooo -RP.................Insert (Class M tolerance)........................... A096 CTooTo....................................Shim............................................................ P011
CNMGoooooo -RS.................Insert (Class M tolerance)........................... A096 CTAHR/Loooo -120.................Small tools holder (For external cutting off)..........
CNMGoooooo -SA.................Insert (Class M tolerance)........................... A093
D018
CNMGoooooo -SH.................Insert (Class M tolerance)........................... A093 CTAHR1010-120S.....................Small tools holder (For external cutting off)..........
CNMGoooooo -SW................Insert (Class M tolerance)........................... A093
D018
CNMGoooooo -SY.................Insert (Class M tolerance)........................... A093 CTANR/Loooo........................MC holder.................................................... P018

CNMMoooooo -HV................Insert (Class M tolerance)........................... A097 CTAPR/L2020............................MC holder.................................................... P018
CNMMoooooo -HX................Insert (Class M tolerance)........................... A097 CTATooooooooo -Bo.........Insert for cutting off...................................... D019
CNMMoooooo -HZ.................Insert (Class M tolerance)........................... A097 CTATooooooo LL/RR...........Insert for cutting off...................................... D019
CPGToooooo........................Insert (Class G tolerance).................. A131,B059 CTBHR/Loooo -ooo..............Small tools holder (For external cutting off)..........
CPGToooooo R/L-F...............Insert (Class G tolerance)........................... A131
D013,D020
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
CTBTooooooooo -B............Insert for cutting off...................................... D020 DCKoooo................................Clamp bridge............................................... P015

CTCHR/Loooo -200.................Small tools holder (For external cutting off).......... DCLNR/Looooooo...............DOUBLE CLAMP holder............................. C008
D021 DCMToooooo........................Insert (Class M tolerance)........................... A133
CTCPR/Looooooo...............MC holder.................................................... P018 DCMToooooo -FM.................Insert (Class M tolerance)........................... A132
CTCToooooooo -B...............Insert for cutting off...................................... D021 DCMToooooo -FP..................Insert (Class M tolerance)........................... A132
CTDHR/L1616-ooo..................Small tools holder (For external cutting off).......... DCMToooooo -FV..................Insert (Class M tolerance)........................... A132
D022 DCMToooooo -LM.................Insert (Class M tolerance)........................... A133
CTDTooooooo N/R-B...........Insert for cutting off...................................... D022 DCMToooooo -LP..................Insert (Class M tolerance)........................... A132
CTDT25350V5R-BS...................Insert for cutting off...................................... D022 DCMToooooo -MK.................Insert (Class M tolerance)........................... A133
CTEooTooo............................Shim (For MMTE holder)............................. G012 DCMToooooo -MM................Insert (Class M tolerance)........................... A133
CTEHR/L1616-ooo..................Small tools holder (For external cutting off).......... DCMToooooo -MP.................Insert (Class M tolerance)........................... A133
D023 DCMToooooo -MV.................Insert (Class M tolerance)........................... A134
CTEToooooooo -B...............Insert for cutting off...................................... D023 DCMToooooo -SV.................Insert (Class M tolerance)........................... A133
CTET30350V5R-BS...................Insert for cutting off...................................... D023 DCMWoooooo......................Insert (Class M tolerance).........A135,B044,B060
CTGNR/Loooo........................MC holder.................................................... P018 DCSo.........................................Spring................. C008,C010,C016,C018 C021
CTGPRoo CAoo......................BC type cartridge.........................................M004
E013 E015,H006 H011
CTIooTooo.............................Shim (For MMTI holder).............................. G013 DCSDooooooo.....................DCSD type end mill..................................... P032
CV type......................................CV type end mill.......................................... P032 DCSNooooooo.....................DCSN type end mill..................................... P032
CWAF10N..................................Adjusting screw (For NF/NR10000/QF10000 type end mill).... DCSSM.......................................Diamond coated drill, Medium, For non-ferrous material....
P029,P030
N254
CWAF10Ro...............................Wedge....................................... L148,P029,P030 DCSSS.......................................Diamond coated drill, Short, For non-ferrous material....

CWAF5R/L.................................Wedge......................................................... P027
N254
CWAHX640WN..........................Wedge..........................................................L031 DCSVN32...................................Shim............................................................ P010

CWAOX445N.............................Wedge..........................................................L032 DCTUooo R/L...........................D type boring head...................................... P024
CWCV20....................................Wedge......................................................... P032 DDJNR/Looooooo...............DOUBLE CLAMP holder............................. C010
CWFSTE....................................Wedge......................................................... P032 DEGXoooooo R/L..................Insert (For AL holder).................................. A136
CWMSE445Ro..........................Wedge................................................ P029,P033 DEGXoooooo R/L-F..............Insert (For AL holder)......................... A136,B066
CWNSE300TR...........................Wedge-T...................................................... P030 DF2MB.......................................Diamond coated end mill.............................. J260
CWSo........................................Wedge................................................ L151,P028 DF2XLB......................................Diamond coated end mill.............................. J261
CWSo R/L..................................Wedge................................................ P028,P029 DF3XB........................................Diamond coated end mill.............................. J278
CWS42SER/L............................Wedge..........................................................L152 DF4JC........................................Diamond coated end mill.............................. J167
CWS42SPR/L............................Wedge..........................................................L150 DF4XL........................................Diamond coated end mill.............................. J168
CWS43SNN...............................Wedge......................................................... P027 DFC4JC.....................................DFC type end mill......................................... J171
CWSEooo SN...........................Wedge-S................................... L034,P030,P033 DFCJRT.....................................DFC type end mill......................................... J172
CWSEoooTN...........................Wedge-T...................................................... P030 DFPSRB.....................................Diamond coated end mill.............................. J345
CWSEoooTR/L........................Wedge-T...........................L034,P028,P030,P033 DGHR/Looooooo.................DG holder.................................................... P022
CWSFoooTRo.........................Wedge-T....................................P027,P029,P030 DKSo.........................................Clamp screw................................................ P003
CWSG20SN...............................Wedge-S......................................................L033 DLC2MA.....................................DLC coated end mill..................................... J086
CWSG20TR................................Wedge-T.......................................................L033 DLC2MB.....................................DLC coated end mill..................................... J265
DNGAoooooo.......................Insert (Class G tolerance).........A103,B027,B055

DNGGoooooo -FJ..................Insert (Class G tolerance)........................... A098
DCooooT................................Clamp screw................................................ P003 DNGGoooooo -PK.................Insert (Class G tolerance)........................... A098

DCBSS.......................................Diamond coated drill, For hard brittle materials.... DNGGoooooo R/L.................Insert (Class G tolerance)........................... A102
N256 DNGMoooooo -MJ.................Insert (Class G tolerance)........................... A100
DCEToooooo R/L-SN............Insert (Class E tolerance)............................ A134 DNGNoooooo.......................Insert (Class G tolerance)........................... B035
DCEToooooo R/L-SR............Insert (Class E tolerance)............................ A134 DNMAoooooo.......................Insert (Class M tolerance)........................... A103
DCEToooooo R/LW-SN.........Insert (Class E tolerance)............................ A135 DNMGoooooo.......................Insert (Class M tolerance)........................... A101
DCGToooooo -AZ..................Insert (Class G tolerance)........................... A132 DNMGoooooo -C...................Insert (Class M tolerance)........................... A100
DCGToooooo M-SMG...........Insert (Class G tolerance)........................... A135 DNMGoooooo -FH.................Insert (Class M tolerance)........................... A098
DCGToooooo R/L-F..............Insert (Class G tolerance)........................... A132 DNMGoooooo -FS.................Insert (Class M tolerance)........................... A098
DCGToooooo R/L-SN............Insert (Class G tolerance)........................... A135 DNMGoooooo -FY.................Insert (Class M tolerance)........................... A098
DCGToooooo R/L-SS............Insert (Class G tolerance)........................... A133 DNMGoooooo -GH................Insert (Class M tolerance)........................... A103
DCGWoooooo.......................Insert (Class G tolerance)........................... A135 DNMGoooooo -GJ.................Insert (Class M tolerance)........................... A103
DCGWoooooo FS..................Insert (Class G tolerance)........................... B044 DNMGoooooo -GK................Insert (Class M tolerance)........................... A101
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
DNMGoooooo -GM................Insert (Class M tolerance)........................... A101 ETANR/Loooooooo.............ML holder.................................................... P018

DNMGoooooo -LK.................Insert (Class M tolerance)........................... A099 ETENNoooooooo................ML holder.................................................... P018
DNMGoooooo -LM................Insert (Class M tolerance)........................... A099 ETFNR/Loooooooo.............ML holder.................................................... P018
DNMGoooooo -LP.................Insert (Class M tolerance)........................... A098 ETHRooooooo.....................ET holder..................................................... P021
DNMGoooooo -LS.................Insert (Class M tolerance)........................... A099 ETJNR/Looooo S...................SL holder..................................................... P019
DNMGoooooo -MA................Insert (Class M tolerance)........................... A101 ETNNR/Looooo S...................SL holder..................................................... P019
DNMGoooooo -MH................Insert (Class M tolerance)........................... A101 ETQNR/Looooo S...................SL holder..................................................... P019
DNMGoooooo -MJ.................Insert (Class M tolerance)........................... A100 ETXNR/Looooooo................ML holder.................................................... P018
DNMGoooooo -MK................Insert (Class M tolerance)........................... A100
DNMGoooooo -MM................Insert (Class M tolerance)........................... A100
DNMGoooooo -MP................Insert (Class M tolerance)........................... A100 FAo............................................Boring unit (Angular type)............................M008

DNMGoooooo -MS................Insert (Class M tolerance)........................... A102 FAo -FAPNooo........................Boring unit (Angular type)............................M008
DNMGoooooo -RK................Insert (Class M tolerance)........................... A102 FAo -FASCooo........................Boring unit (Angular type)............................M008
DNMGoooooo -RM................Insert (Class M tolerance)........................... A102 FAo -FASPooo........................Boring unit (Angular type)............................M008
DNMGoooooo -RP.................Insert (Class M tolerance)........................... A102 FAPNoo....................................Cartridge (For boring unit)...........................M008
DNMGoooooo -RS.................Insert (Class M tolerance)........................... A103 FASCoo....................................Cartridge (For boring unit)...........................M008
DNMGoooooo -SA.................Insert (Class M tolerance)........................... A099 FASPoo....................................Cartridge (For boring unit)...........................M008
DNMGoooooo -SH.................Insert (Class M tolerance)........................... A099 FBE2 type..................................FBE2 type end mill...................................... P034
DNMGoooooo -SY.................Insert (Class M tolerance)........................... A099 FC400890T................................Clamp screw................................................ P004
DNMMoooooo -HZ.................Insert (Class M tolerance)........................... A103 FCDG4ooo R/Loo...................FCDG4 type boring bar............................... P025
DNMXoooooo -MW................Insert (Class M tolerance)........................... A101 FCL5ooo R/L............................FCL5 type boring bar................................... P025
DNMXoooooo -SW................Insert (Class M tolerance)........................... A099 FCSKooo R/L...........................FCSK type boring bar.................................. P024
DPCLooo R/L...........................D type boring head............................. E040,P024 FCTUooo R/L...........................FCTU type boring bar......................... E026,P024
DPDHooo R/L...........................D type boring head............................. E040,P024 FE404R/Looooo.....................FE404 type face mill.....................................L152
DPDUooo R/L...........................D type boring head............................. E039,P024 FF3000Rooooo......................FF3000 type face mill...................................L149
DPDZooo R/L...........................D type boring head...................................... P024 FF3000 type...............................FF3000 type end mill................................... P032
DPSKooo R/L...........................D type boring head...................................... P024 FFAWR.......................................Adjusting wedge...........................................L149
DPT2ooo R...............................D type boring head.............................G032,P024 FFCSR........................................Cartridge (For FF3000 type face mill)..........L149
DPT4ooo R...............................D type boring head............................. F132,P024 FFL.............................................Lever............................................................L149
DPTFooo R/L...........................D type boring head............................. E039,P024 FFLB..........................................Lever screw..................................................L149
DPVPooo R/L...........................D type boring head............................. E041,P024 FFP.............................................Lock pin.............................................. L149,P032
DTGNR/Looooooo...............DOUBLE CLAMP holder............................. C016 FFRP..........................................Radial spring................................................L149
DVJNR/Looooooo................DOUBLE CLAMP holder............................. C018 FFSS..........................................Shim................................................... L149,P032
DVPNR/Looooooo...............DOUBLE CLAMP holder............................. C020 FFW............................................Washer.........................................................L149
DVVNNooooooo..................DOUBLE CLAMP holder............................. C019 FN548 type................................FN548 type face mill.................................... P028
DWLNR/Looooooo..............DOUBLE CLAMP holder............................. C021 FP490R/Looooo.....................FP490 type face mill.....................................L150
FP590R/Looooo.....................FP590 type face mill.....................................L151

FSCLCoooo R/L-oo E............DIMPLE BAR (Carbide shank).................... E006
Eoo...........................................Stop ring..............C018 C020,E041,F132,G032 FSCLCoooo R/L-oo S............DIMPLE BAR............................................... E006

Eooo SCLPRoo......................COBRA type boring bar (Carbide shank).... P023 FSCLCoooo R-oo E-o /o........DIMPLE BAR (Carbide shank).................... E006
Eooo STFPRoo.......................COBRA type boring bar (Carbide shank).... P023 FSCLPoooo R/L-oo E.............DIMPLE BAR (Carbide shank).................... E006
Eoo Moooo.............................ML holder (Old type tool)............................. P018 FSCLPoooo R/L-oo S.............DIMPLE BAR............................................... E006
Eoo R/Loooo..........................ML holder (Old type tool)............................. P018 FSCLPoooo R-oo E-o /o........DIMPLE BAR (Carbide shank).................... E006
E404 type...................................E404 type face mill...................................... P028 FSDQCoooo R/L-oo E............DIMPLE BAR (Carbide shank).................... E009
ECMP type.................................ECMP type end mill..................................... P032 FSDQCoooo R/L-oo S............DIMPLE BAR............................................... E009
EGHRoooooo........................EG holder.................................................... P021 FSDUCoooo R/L-oo E............DIMPLE BAR (Carbide shank).................... E008
EGSooooo.............................Clamp screw................................................ P004 FSDUCoooo R/L-oo S............DIMPLE BAR............................................... E008
EPSS..........................................Straight shank drill, Plate pal....................... N183 FSL5ooo R...............................FSL5 type boring bar..........................F130,G030
ESBNR/Looooooo...............ML holder.................................................... P018 FSTE type..................................FSTE type cutter......................................... P032
ESDNR/Looooooo...............ML holder.................................................... P018 FSTUooo R/L...........................FSTU type boring bar.................................. E025
ESENR/Looooooo...............ML holder.................................................... P018 FSTUPoooo R/L-oo E.............DIMPLE BAR (Carbide shank).................... E007
ESKNR/Looooooo...............ML holder.................................................... P018 FSTUPoooo R/L-oo S.............DIMPLE BAR............................................... E007
ESS42........................................Shim............................................................ P010 FSTUPoooo R-oo E-o /o........DIMPLE BAR (Carbide shank).................... E007
ESToo.......................................Shim............................................................ P010 FSVJBoooo R/L-oo S.............DIMPLE BAR............................................... E012
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
FSVJCoooo R/L-oo S.............DIMPLE BAR............................................... E012 GYAR/Looo 90o -ooo............GY holder......................................... F094 F101
FSVPBoooo R/L-oo S............DIMPLE BAR............................................... E011 GYDR/Looo 90o -Moo R/L......GY holder......................................... F094 F101
FSVPCoooo R/L-oo S............DIMPLE BAR............................................... E011 GYHR/Looooo 00-Moo R/L....GY holder.................... F030 F041,F052 F083
FSVUBoooo R/L-oo S............DIMPLE BAR............................................... E011 GYHR/Looooo 50-Moo R/L....GY holder......................................... F050 F051
FSVUCoooo R/L-oo S............DIMPLE BAR............................................... E011 GYHR/Looooo 90-Moo R/L....GY holder.................... F044 F049,F084 F093
FSWLooo R/Lo........................FSWL type boring bar................................. E027 GYMoo R/Lo -ooo...................Modular blade................................... F030 F101
FSWUBoooo R/L-oo E...........DIMPLE BAR (Carbide shank).................... E010 GYPR/Looooo 00-K25............GY holder......................................... F042 F043
FSWUBoooo R/L-oo S...........DIMPLE BAR............................................... E010 GYQR/Looooo 00-ooo.........GY holder......................................... F030 F041
FSWUBoooo R-oo E-o /o......DIMPLE BAR (Carbide shank).................... E010 GYSR/Loooo JX00-ooo........GY holder......................................... F028 F029
FSWUPoooo R/L-oo E...........DIMPLE BAR (Carbide shank).................... E010
FSWUPoooo R/L-oo S...........DIMPLE BAR............................................... E010
FSWUPoooo R-oo E-o /o.......DIMPLE BAR (Carbide shank).................... E010 H100TH-Boo -ooo..................HSK boring bar holder................................. H022
FVo............................................Boring unit (Vertical type)............................M008 H100TH-EN3232R/L-130...........HSK boring bar holder................................. H020
FVo -FVPNooo........................Boring unit (Vertical type)............................M008 H100TH-EV3232R/L-180...........HSK boring bar holder................................. H019
FVo -FVSCooo........................Boring unit (Vertical type)............................M008 H63TH-Aooo DCLNR/L12........HSK DCLN type holder............................... H008
FVo -FVSPooo.........................Boring unit (Vertical type)............................M008 H63TH-Boo -oo.......................HSK boring bar holder................................. H021
FVPNooo.................................Cartridge (For boring unit)...........................M008 H63TH-DCLNL-L12-3................HSK DCLN type holder............................... H008
FVSCooo.................................Cartridge (For boring unit)...........................M008 H63TH-DCLNR/L-DX12.............HSK DCLN type holder............................... H006
FVSPooo.................................Cartridge (For boring unit)...........................M008 H63TH-DCMNN-o12.................HSK DCMN type holder.............................. H007
H63TH-DDJNL-L15-3................HSK DDJN type holder................................ H011
H63TH-DDJNR/L-DX15.............HSK DDJN type holder................................ H009
G2MS.........................................HSS end mill................................................. J387 H63TH-DDNNN-o15..................HSK DDNN type holder............................... H010

G4LC..........................................HSS end mill................................................. J410 H63TH-EN2525R/L-115.............HSK boring bar holder................................. H020
G4MC.........................................HSS end mill................................................. J404 H63TH-EV2020R/L-105-3..........HSK boring bar holder................................. H021
GBE............................................GBE type end mill......................................... J192 H63TH-EV2525R/L-112.............HSK boring bar holder................................. H019
GCMToooooo -Uo.................Insert (For TAF type drill)...................K048,N244 H63TH-MGHR/L-DX43oo.........HSK MG type holder................................... H014
GDCN2004PDFR3.....................Insert (For NF10000/QF10000 type cutter).......... H63TH-MMTENR-o16...............HSK MMTE type holder............................... H016
K044,L148 H63TH-MMTER-DX16................HSK MMTE type holder............................... H016
GDCN2004PDR.........................Insert (For AF10000 type cutter)................. K044 H63TH-MTHR/L-DX43...............HSK MTH type holder................................. H017
GDCN2004ZDTR1.....................Insert (For NR10000 type cutter)................. K044 H63TH-PCLNR/L-DX12.............HSK PCLN type holder................................ H006
GMR...........................................HSS end mill................................................. J428 H63TH-PCMNN-o12..................HSK PCMN type holder............................... H007
GPMToooooo -Uo.................Insert (For TAF type drill)...................K048,N244 H63TH-PDJNR/L-DX15.............HSK PDJN type holder................................ H009
GSD............................................Straight shank drill, TiN............................... N166 H63TH-PDNNN-o15..................HSK PDNN type holder............................... H010
GSFPR.......................................HSS end mill................................................. J414 H63TH-PRDCN-o12..................HSK PRDC type holder............................... H012
GTo HR/Loooo -ooo.............Small tools holder (External grooving)........ D016 H63TH-PRGCR/L-DX12.............HSK PRGC type holder............................... H012
GToTooooooo R/L-E...........Insert (For small tools holder)...................... D017 H63TH-SVPBR/L-DX16.............HSK SVPB type holder................................ H013
GToTooooooo R/L-U...........Insert (For small tools holder)...................... D016 H63TH-SVVBN-o16..................HSK SVVB type holder................................ H013
GToTooooooo R-VT............Insert (For small tools holder)...................... D017 HBHooooo.............................Clamp screw................................................ P002
GToTR/L....................................Insert (Blank)............................................... D017 HBHAooooo...........................Clamp screw................................................ P002
GTD............................................Taper shank drill, TiN.................................. N184 HDSooooo.............................Clamp screw................................................ P009
GTTD..........................................Taper shank drill, TiN, For steel frame........ N195 HFF06015..................................Clamp screw................................................ P004
GWSL.........................................Straight shank drill, TiN, Extra long............. N178 HFF08043H................................Clamp screw................................................ P009
GWSS.........................................Straight shank drill, TiN, For deep hole, Convolute flute.... HGM-PTo /o..............................Plug.............................. E035 E038,H007,H010
N176
H012,H013,H016,H019
GWTS.........................................Taper shank drill, TiN, For deep hole, Convolute flute.... HKYoo D...................................Driver........................................................... P002
N191 HKYoo F....................................Flag wrench................................................. P002
GY05016S..................................Clamp screw................................................ P004 HKYoo L....................................L-wrench...................................................... P002
GY06013M.................................Clamp screw................................................ P004 HKYoo R...................................L-wrench...................................................... P002
GY1Booooo 020N..................Insert (For GY holder)..................................F014 HKYooT....................................T-wrench..................................................... P002
GY1Goooooooo N-GFGS....Insert (For GY holder)........................ B053,F013 HLSo.........................................Lever spring.................................................M003
GY2Booooo 020N..................Insert (For GY holder)..................................F014 HPo............................................Spring...........................................................L149
GY2Goooooooo N-MF.........Insert (For GY holder)..................................F013 HPoo.........................................Clamp pin.........................................E035 E038
GY2Moooooooo N-oo........Insert (For GY holder)...................... F012 F014 HRoo.........................................Spanner............................................. M009,P026
GY2Moooooooo R/L05-GM....Insert (For GY holder)..................................F012 HSoo.........................................Clamp screw................................................ P004
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
HSCooooo.............................Clamp screw................................................ P009 LK1.............................................Clamp bridge............................................... P015

HSK-oooo M............................HSK type taper tool number........................M023 LLCLooo..................................Clamp lever................................................. P013
HSP05008C...............................Lock screw.................................................. P004 LLCSooo.................................Clamp screw................................................ P005
HSSooooo..............................Clamp screw................................................ P002 LLCSooo S...............................Clamp screw................................................ P005
HYo............................................Unit screw.................................................... P004 LLPoo.......................................Shim pin...................................................... P013
HY-A1.........................................Unit screw.................................................... P004 LLRo..........................................Radial screw................................................ P004
HY-V1.........................................Unit screw.................................................... P004 LLSCNoo..................................Shim............................................................ P010
LLSCPoo..................................Shim............................................................ P010
LLSDNoo..................................Shim............................................................ P010
IMXoo -ooooooo Looo C....Indexable head end mill............................... J454 LLSDPoo..................................Shim............................................................ P010
IMX-oo HV.................................Indexable head end mill....................................... LLSRNooo...............................Shim............................................................ P010
J439,J440,J444,J446,J447 LLSSNoo..................................Shim............................................................ P010
IMX-o3A....................................Indexable head end mill...................... J442,J453 LLSSP42....................................Shim............................................................ P010
IMX-o 4HV-o..............................Indexable head end mill............. J441,J445,J449 LLSTE32....................................Shim............................................................ P011
IMX-Coo HV..............................Indexable head end mill............................... J450 LLSTNoo..................................Shim............................................................ P011
IMX-C4FD-C...............................Indexable head end mill............................... J451 LLSTPoo..................................Shim............................................................ P011
IMX-C4FV...................................Indexable head end mill............................... J452 LLSWNooo..............................Shim............................................................ P011
IMX-R4F.....................................Indexable head end mill............................... J443 LLSWPooo..............................Shim............................................................ P011
LR...............................................HSS end mill................................................. J432
LRBooo...................................Insert for brazed tool holder (MITSUBISHI standard)....
JDMTooooooZDER-JL.........Insert (For AJX type cutter)................ K024,L089
I004
JDMTooooooZDSR-JM........Insert (For AJX type cutter)....... K024,L089,L140 LSo............................................Clamp screw................................................ P005

JDMTooooooZDSR-ST.........Insert (For AJX type cutter)....... K024,L089,L140 LSoo.........................................Clamp screw................................................ P005
JDMWooooooZDSR-FT........Insert (For AJX type cutter)....... K024,L089,L140 LSooooT.................................Clamp screw................................................ P005
JENS42......................................Shim............................................................ P032 LSooT.......................................Clamp screw................................................ P005
JFS-o.........................................JUST FIT SLEEVE set number................... N246 LS10TS......................................Clamp screw................................................ P005
JFSoooo -oo..........................JUST FIT SLEEVE (JFS)............................ N246 LS24H........................................Clamp screw................................................ P005
JKDS4........................................Cartridge (For DCSD/DCSN type end mill).... P032 LSD............................................Straight shank drill, Extra long..................... N180
JKNS4........................................Cartridge (For DCSD/DCSN type end mill).... P032 LSE445R type...........................LSE445 type face mill.................................. P028
JOMTooooooZZSR-JM........Insert (For AJX type cutter)....... K024,L089,L140 LTD.............................................Taper shank drill, Extra long........................ N192
JOMWooooooZZSR-FT........Insert (For AJX type cutter)....... K024,L089,L140
JPMToooooo -o....................Insert (For TAB/CBJP type end mill).... K025,L137
JPMXoooooo -oo.................Insert (For SPX type end mill)............ K025,L110 MAEoooo MB..........................MAE type drill (External coolant)................. N129
JR...............................................HSS end mill................................................. J431 MASoooo LB/MB....................MAS type drill (Internal coolant).................. N129
JSSo..........................................Shim screw.................................................. P004 MBAooooo H..........................Clamp screw................................................ P009
MCLNRooooooo..................DOUBLE CLAMP holder (For heavy cutting).......

C009
KGBNoo -oo............................Tool block (For UG holder)...........................F120 MCSoooooX3DB...................CVD diamond coated drill............................ N252
KGC1.........................................Clamp bridge............................................... P015 MESo.........................................Spring.................... C017,F122,G022,P021,P022
KGTo N......................................Insert (For UG holder)..................................F121 MG200 type...............................MG200 type end mill................................... P033
KGTo R/L...................................Insert (For UG holder)..................................F121 MG245 type...............................MG245 type end mill................................... P033
KKCR/L445................................MH holder.................................................... P018 MG2R/Looooooooo............MG2 type holder.......................................... P020
KMH...........................................HSS end mill................................................. J399 MG300 type...............................MG300 type face mill................................... P029
KSo............................................Axial screw.................................................. P004 MG300 type...............................MG300 type end mill................................... P033
KSoo.........................................Set bolt........................................................ P004 MG345 type...............................MG345 type face mill................................... P029
KSo S.........................................Pre-set screw.............................................. P004 MG345 type...............................MG345 type end mill................................... P033
KSD............................................Straight shank drill, Cobalt HSS, For stainless steel.... MG400 type...............................MG400 type face mill................................... P029
N174 MG445 type...............................MG445 type face mill................................... P029
KSMGRoo Soo........................KSMG type end mill......................................L138 MGDoo.....................................Driver........................................................... N125
KTD............................................Taper shank drill, Cobalt HSS..................... N189 MGEEWooooAFTR................Insert (For MG245/345/445 type cutter)...... K025
KYoo.........................................Spanner....................................................... P018 MGEEWoooo PFTR................Insert (For MG200/300/400 type cutter)...... K025
MGHR/Looooooooo...........MG holder........................................... F122,P020

MGP445 type.............................MGP445 type face mill................................ P029
LDCN190412R/L........................Insert (For AF5000 type face mill)............... K044 MGSoooo Looo B..................Solid gun drill............................................... N124
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
MGS6.........................................Clamp screw................................................ P005 MS4LT........................................MSTAR end mill........................................... J360

MGTR/Looooo.......................Insert (For MG holder)............... B054,F123,F133 MS4LTB.....................................MSTAR end mill........................................... J369
H015,L139 MS4MC.......................................MSTAR end mill........................................... J133
MHK5NR/L.................................Clamp bridge............................................... P015 MS4MRB....................................MSTAR end mill........................................... J308
MHSoooo Looo B..................MHS type drill (Internal coolant).................. N085 MS4SC.......................................MSTAR end mill........................................... J132
MHSooo R/L.............................Shim............................................................ P011 MS4XL.......................................MSTAR end mill........................................... J137
MHT1..........................................Clamp screw................................................ P005 MSBNRooooooo..................DOUBLE CLAMP holder (For heavy cutting).......
MK1K.........................................Anti-seize lubricant...................................... P038
C012
MK1KS.......................................Anti-seize lubricant...................................... P038 MSCN63.....................................Shim............................................................ P011

MLCP42.....................................Shim............................................................ P011 MSD445 type.............................MSD445 type face mill................................ P029
MLDP42.....................................Shim............................................................ P011 MSEoooo SB...........................MSE type drill.............................................. N120
MLGoooo L..............................Insert (For FSL5 type boring bar).......F131,G031 MSE445 type.............................MSE445 type face mill................................. P029
MLSP42.....................................Shim............................................................ P011 MSE445 type.............................MSE445 type end mill................................. P033
MLToooo L..............................Insert (For FSL5 type boring bar).......F131,G031 MSJHD.......................................MSTAR end mill........................................... J130
MLTP32......................................Shim............................................................ P011 MSMHD......................................MSTAR end mill........................................... J127
MMSooooXo DB.....................MMS type drill (Internal coolant).................. N070 MSMHDRB.................................MSTAR end mill........................................... J311
MMToo ERooooooo............Insert (For MMTE holder)..................................... MSMHZD....................................MSTAR end mill........................................... J108
G014,G016,G018,G020 MSP0300SB...............................MSP type starting drill................................. N123
MMToo IRooooooo.............Insert (For MMTI boring bar)................................
MSSHD.......................................MSTAR end mill........................................... J126
G015,G017,G019,G021 MSSN63.....................................Shim............................................................ P011

MMTERooooooo -o..............MMTE holder............................................... G012 MSSNRooooooo..................DOUBLE CLAMP holder (For heavy cutting).......
MMTIRooooAooo -oooo....MMTI boring bar.......................................... G013
C014
MNSoooo LB...........................MNS type drill (Internal coolant).................. N077 MT1R/Loooooo.....................MT1 type holder.......................................... G022
MNSooooXoo DB..................MNS type drill (Internal coolant).................. N077 MT2R/L2525M4.........................MT2 type holder.......................................... P020
MP2MB.......................................MS Plus end mill........................................... J207 MTENNooooooo..................WP holder.................................................... P019
MP2SB.......................................MS Plus end mill........................................... J206 MTHR/Loooooo....................MT holder.................................................... G022
MP2SSB.....................................MS Plus end mill........................................... J205 MTJNR/Looooooo...............WP holder...........................................C017,P019
MP2XLB.....................................MS Plus end mill........................................... J209 MTKo R/L...................................Clamp bridge............................................... P015
MP6............................................Shim............................................................ P013 MTNNR/Looooooo...............WP holder.................................................... P019
MPMToooooo.......................Insert (For CBMP/ECMP/TAB type end mill)........ MTQNR/Looooooo...............WP holder.................................................... P019
K025,L137 MTTR/Loooooo.....................Insert (For MT holder/D type boring head)...........
MPMWoooooo......................Insert (For TSMP type end mill)......... K025,L136
G023,G033,H018
MPMX120412-oo......................Insert (For SPX type end mill)............ K026,L110 MVEooooXoo Sooo.............MVE type drill (External coolant)................. N024
MQSooooXo DB.....................MQS type drill (Internal coolant).................. N063 MVSooooXoo Sooo.............MVS type drill (Internal coolant).................. N012
MR..............................................HSS end mill................................................. J430 MVXooooXo Foo...................MVX type drill (Internal coolant).................. N212
MRB...........................................HSS end mill................................................. J434 MWEoooo MA/MB/SA/SB.......MWE type drill (External coolant)................ N054
MS2ES.......................................MSTAR end mill........................................... J065 MWLNR/Looooooo..............WP holder.................................................... P019
MS2JS........................................MSTAR end mill........................................... J054 MWSoooo LB/MB/SB/XB........MWS type drill (Internal coolant)................. N032
MS2LS.......................................MSTAR end mill........................................... J056 MWSooooXoo DB..................MWS type drill (Internal coolant)................. N032
MS2MB.......................................MSTAR end mill........................................... J219 MWSooooX8DB.....................MWS type drill (Internal coolant)................. N032
MS2MD.......................................MSTAR end mill........................................... J052 MZEooooo Moo....................STEP drill (External coolant)....................... N113
MS2MRB....................................MSTAR end mill........................................... J287 MZEoooo MA/SA/SB...............MZE type drill (External coolant)................. N096
MS2MS.......................................MSTAR end mill........................................... J049 MZSooooo Moo....................STEP drill (Internal coolant)........................ N113
MS2MT.......................................MSTAR end mill........................................... J355 MZSoooo LB/MB/XB...............MZS type drill (Internal coolant).................. N096
MS2MTB....................................MSTAR end mill........................................... J367
MS2SB.......................................MSTAR end mill........................................... J217
MS2SS.......................................MSTAR end mill........................................... J048 Noo Moo..................................MC holder (Old type tool)............................ P017
MS2XL.......................................MSTAR end mill........................................... J058 Noo R/Loo...............................MC holder (Old type tool)............................ P017
MS2XL6.....................................MSTAR end mill........................................... J062 NAo...........................................Boring unit (Angular type)............................ P026
MS2XLB.....................................MSTAR end mill........................................... J221 NAPNoo....................................Cartridge (For boring unit)........................... P026
MS2XLRB..................................MSTAR end mill........................................... J290 NASPoo....................................Cartridge (For boring unit)........................... P026
MS3ES.......................................MSTAR end mill........................................... J110 NF10000Rooooo....................NF10000 type face mill.................................L148
MS4EC.......................................MSTAR end mill........................................... J141 NNMU200608ZEN-oo...............Insert (For AHX640W type cutter)........................
MS4JC.......................................MSTAR end mill........................................... J135
K026,L028,L030
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
NNMU200708ZEN-MP...............Insert (For AHX640S type cutter)....... K026,L028 NP-WCMWoooooo FA..........Insert (Class M tolerance)........................... B049
NNMU200712ZER-MM..............Insert (For AHX640S type cutter)....... K026,L028 NP-WFC42ZFER2......................Insert (For BF407QBF407 type face mill).... K047
NP-CCGBoooooo GA2..........Insert (Class G tolerance)........................... B039 NP-WNGAoooooooo3........Insert (Class G tolerance)........................... B034
NP-CCGWooooooo.............Insert (Class G tolerance)........................... B040 NP-WNGAoooooooo 6........Insert (Class G tolerance)........................... B034
NP-CCGWooooooo2...........Insert (Class G tolerance)........................... B039 NP-WNGAooooooooWS3....Insert (Class G tolerance)........................... B034
NP-CCGWooooooooWS2....Insert (Class G tolerance)........................... B040 NPXMoooo Soo.....................NPX type drill............................................... P037
NP-CCMBoooooo G..............Insert (Class M tolerance)........................... B040 NR10000 type............................NR10000 type face mill............................... P029
NP-CCMHoooooo.................Insert (Class M tolerance)........................... B059 NSooo......................................Clamp screw................................................ P006
NP-CCMWoooooo................Insert (Class M tolerance)........................... B059 NSoooW..................................Clamp screw................................................ P006
NP-CCMWoooooo F..............Insert (Class M tolerance)........................... B041 NTFoooo R..............................NT holder..................................................... P025
NP-CNGAoooooooo 4.........Insert (Class G tolerance)........................... B022 NVo............................................Boring unit (Vertical type)............................ P026
NP-CNGAooooooo2............Insert (Class G tolerance)........................... B023 NVPNoo....................................Cartridge (For boring unit)........................... P026
NP-CNGAooooooooWS2...Insert (Class G tolerance)........................... B023 NVSPoo....................................Cartridge (For boring unit)........................... P026
NP-CNGAooooooooWS4...Insert (Class G tolerance)........................... B022
NP-CNMAooooooo..............Insert (Class M tolerance)........................... B024
NP-CNMMoooooo R/L-F.......Insert (Class M tolerance)........................... B055 OCTACUTooooooo.............OCTACUT type face mill.....................L095,L096

NP-CPGBoooooooo2.........Insert (Class G tolerance)........................... B042 OCTACUTooo Soooo...........OCTACUT type end mill...............................L094
NP-CPMBoooooo G..............Insert (Class M tolerance)........................... B042 OEMXoooo Eo Ro..................Insert (For OCTACUT type cutter).......................
NP-CPMHoooooo.................Insert (Class M tolerance)........................... B059
K026,K044,L094
NP-DCGWooooooo.............Insert (Class G tolerance)........................... B044 OEMXoooo Eo R1-JS..............Insert (For OCTACUT type cutter)..... K027,L094
NP-DCGWooooooo2...........Insert (Class G tolerance)........................... B043
NP-DCMToooooo R/L-F........Insert (Class M tolerance)........................... B060
NP-DCMWooooooo.............Insert (Class M tolerance)........................... B044 PoooAM...................................Pin....................................................E035 E038

NP-DNGAoooooooo 4.........Insert (Class G tolerance)........................... B025 Pooo US...................................Lock pin....................................................... P014
NP-DNGAooooooo2............Insert (Class G tolerance)........................... B026 PoooW.....................................Lock pin....................................................... P014
NP-DNGAooooooooWS2JR/L...Insert (Class G tolerance)........................... B027 PoooWS...................................Lock pin....................................................... P014
NP-DNMAooooooo..............Insert (Class M tolerance)........................... B027 Poo Moo..................................MC holder (Old type tool)............................ P017
NP-DNMMoooooo R/L-F.......Insert (Class M tolerance)........................... B055 Poo R/Loo................................MC holder (Old type tool)............................ P017
NP-GDCN2004PDSR3...............Insert (For NF10000 type face mill).... K044,L148 Poo S.........................................Lock pin....................................................... P014
NP-GDCW1240PDFR2..............Insert (For V10000 type face mill)...... K044,L147 P425 type...................................P425 type face mill...................................... P029
NP-SNGAooooooo2............Insert (Class G tolerance)........................... B028 P525 type...................................P525 type face mill...................................... P029
NP-SNGAoooooo GA4..........Insert (Class G tolerance)........................... B028 PCBNR/Looooooo...............LL holder............................................C009,P017
NP-SNMAooooooo..............Insert (Class M tolerance)........................... B028 PCFNR/Looooooo...............LL holder..................................................... P017
NP-SNMMoooooo R/L-F.......Insert (Class M tolerance)........................... B056 PCLNR/Looooooo...............LL holder............................................C008,P017
NP-TCGWoooooooo3.........Insert (Class G tolerance)........................... B045 PCLNR/Loo CAoo...................LL type cartridge..........................................M002
NP-TNGAooooooo3.............Insert (Class G tolerance)........................... B030 PDHNR/Looooooo...............LL holder..................................................... C011
NP-TNGAooooooo 6.............Insert (Class G tolerance)........................... B030 PDJNR/Looooooo................LL holder..................................................... C010
NP-TNMAooooooo..............Insert (Class M tolerance)........................... B031 PMCoo RoooAMoooo.........PMC type end mill........................................L140
NP-TNMMoooooo R/L-F........Insert (Class M tolerance)........................... B056 PMFoooooAoo R..................PMF type end mill.........................................L142
NP-TPGBoooooooo3..........Insert (Class G tolerance)........................... B046 PMFAoo R.................................Cartridge (For PMF type end mill)................L142
NP-TPGXooooooo...............Insert (Class G tolerance)........................... B047 PMRooooooo R....................PMR type end mill........................................L143
NP-TPGXooooooo3.............Insert (Class G tolerance)........................... B046 PMRooooooAoo R...............PMR type end mill........................................L143
NP-TPMBoooooo G...............Insert (Class M tolerance)........................... B046 PRDCNooooooo..................LL holder............................................C024,P017
NP-TPMHoooooo R/L-F........Insert (Class M tolerance)........................... B062 PRGCR/Looooooo...............LL holder............................................C024,P017
NP-TPMXoooooo R/L-F........Insert (Class M tolerance)........................... B062 PSoo.........................................Shim............................................................ P010
NP-VBGToooooo R-F............Insert (Class G tolerance)........................... B064 PSBNR/Looooooo...............LL holder............................................C012,P017
NP-VBGWoooooooo2.........Insert (Class G tolerance)........................... B048 PSDNNooooooo..................LL holder..................................................... C014
NP-VBGWoooooo G..............Insert (Class G tolerance)........................... B048 PSKNR/Looooooo...............LL holder............................................C015,P017
NP-VCGToooooo R-F............Insert (Class G tolerance)........................... B064 PSKNR/Loo CAoo...................LL type cartridge..........................................M002
NP-VCGWoooooooo2.........Insert (Class G tolerance)........................... B049 PSSNR/Looooooo...............LL holder............................................C013,P017
NP-VNGAooooooo2............Insert (Class G tolerance)........................... B032 PSSNR/Loo CAoo...................LL type cartridge..........................................M002
NP-VNGAooooooo 4............Insert (Class G tolerance)........................... B032 PSTNR/Looooooo................LL holder..................................................... C013
NP-VNMAooooooo..............Insert (Class M tolerance)........................... B033 PSYNRoo CAoo......................LL type cartridge..........................................M002
NP-VNMMoooooo R/L-F.......Insert (Class M tolerance)........................... B057 PToo.........................................Shim............................................................ P010
10
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
PTooTo R.................................Shim............................................................ P011 Sooo SCLCR/Loo...................S type boring bar (Steel shank)................... E030
PTANR/Looooooo...............LL holder..................................................... P017 Sooo SCLPR/Loo...................COBRA type boring bar (Steel shank)........ P023
PTBNR/Looooooo...............LL holder..................................................... P017 Sooo SCZCR/Loo...................S type boring bar (Steel shank).......... E034,P023
PTFER/Looooooo................AL holder..................................................... P020 Sooo SDQCR/Loo..................S type boring bar (Steel shank).......... E031,P023
PTFNR/Looooooo................LL holder............................................C017,P017 Sooo SDUCR/Loo..................S type boring bar (Steel shank)................... E029
PTFNR/Loo CAoo...................LL type cartridge..........................................M002 Sooo SDZCRoo......................S type boring bar (Steel shank)................... P023
PTGER/Looooooo...............AL holder..................................................... P020 Sooo SSKCR/Loo...................S type boring bar (Steel shank).......... E033,P023
PTGNR/Looooooo...............LL holder............................................C016,P017 Sooo STFCR/Loo...................S type boring bar (Steel shank)................... E028
PTGNR/Loo CAoo...................LL type cartridge..........................................M002 Sooo STFER/Loo...................AL type boring bar (Steel shank)................. E042
PTTNR/Looooooo................LL holder..................................................... P017 Sooo STFPRoo.......................COBRA type boring bar (Steel shank)........ P023
PTTNRoo CAoo.......................LL type cartridge..........................................M002 Sooo SVQCR/Loo..................S type boring bar (Steel shank)................... E032
PVooo......................................Shim............................................................ P012 Sooo SVUCR/Loo...................S type boring bar (Steel shank)................... E033
PVJNR/Looooooo................MP holder.................................................... C018 Sooo SWLPR/Loo..................COBRA type boring bar (Steel shank)........ P023
PVPNR/Looooooo...............MP holder...........................................C020,P020 S2MD.........................................HSS end mill................................................. J385
PVVNNooooooo...................MP holder...........................................C019,P020 S2SDA.......................................HSS end mill................................................. J396
PWLNR/Looooooo...............LL holder..................................................... C021 S4JC..........................................HSS end mill................................................. J408
S4MD.........................................HSS end mill................................................. J402
SBAooo -ES-M.........................Parts for ABS head......................................M021
QBooooooo..........................Q type quick change....................................M017 SBAooo -ES-Mo......................Parts for ABS head......................................M021

QBF407Roooo Q.....................QBF407 type Qing cutter............................. P029 SBAHRoooo...........................Boring holder............................................... D030
QBP415Roooo Q.....................QBP415 type Qing cutter............................ P030 SBAToooooo L......................Insert (For SBAHR type holder).................. D030
QF10000Roooo Q...................QF10000 type Qing cutter........................... P030 SBAToooooo L-B..................Insert (For SBAHR type holder).................. D030
QFAoooooo..........................T type quick change....................................M015 SBHoooo R..............................Square type holder (For MICRO-DEX/MICRO-MINI type boring bar)....
QFAooooo Bo R/L..................Q type quick change....................................M014
E024,F129,G029
QFAooooo No R/L..................Q type quick change....................................M014 SBRooo...................................MI holder.....................................................M011

QFBoooooo R/L....................Q type quick change....................................M015 SCoo Moo Sooo S/L...............Arbors for screw-in tools...............................L145
QOGToooo R-G1.....................Insert (For AQX type end mill)............ K027,L079 SCoo Moo Sooo SW/LW........Arbors for screw-in tools...............................L145
QOMToooo R-M2....................Insert (For AQX type end mill)............ K027,L079 SCoo Moo Soo -HSK63A........Arbors for screw-in tools...............................L146
QPAR1.......................................Guide plate......................................... P029,P030 SCoo Moo S10-BToo.............Arbors for screw-in tools...............................L146
QPCR1.......................................Guide plate.................................................. P030 SCACR/Looooooo -SM........Small tools holder (External front turning).... D008
QSE415Roooo Q.....................QSE415 type Qing cutter............................ P030 SCD43........................................Shim............................................................ P028
QWGR1......................................Wedge-T...................................................... P030 SCLCR/Looooooo...............SP holder..................................................... C022
SCLCR/Looooooo -SM.........Small tools holder (External front turning).... D008
RBHoooo N.............................Arbor (For MICRO-DEX/MICRO-MINI type boring bar)....
SCMToooooo -FM.................Insert (Class M tolerance)........................... A138
SCMToooooo........................Insert (Class M tolerance)........................... A139

E018,E023,F128,G028 SCMToooooo -FP..................Insert (Class M tolerance)........................... A138
RCGToooo M0-AZ...................Insert (Class G tolerance)........................... A137 SCMToooooo -FV..................Insert (Class M tolerance)........................... A138
RCMToooo M0........................Insert (Class M tolerance)........................... A137 SCMToooooo -LM.................Insert (Class M tolerance)........................... A138
RCMXoooo M0........................Insert (Class M tolerance)........................... A137 SCMToooooo -LP..................Insert (Class M tolerance)........................... A138
RCMXoooo M0-RR..................Insert (Class M tolerance)........................... A137 SCMToooooo -MK.................Insert (Class M tolerance)........................... A138
RDMWoooo M0E.....................Insert (For ARX type end mill)............ K027,L098 SCMToooooo -MM................Insert (Class M tolerance)........................... A139
REMXoooo EN-JS...................Insert (For OCTACUT type cutter)..... K027,L094 SCMToooooo -MP.................Insert (Class M tolerance)........................... A138
REMXoooo SN........................Insert (For OCTACUT type cutter)..... K027,L094 SCMWoooooo.......................Insert (Class M tolerance)........................... A139
RGEN2004M0o N.......................Insert (For SG20 type cutter).............. K028,L033 SCPooo R/L.............................Shim............................................................ P029
RNGNoooooo.......................Insert (Class G tolerance)........................... B036 SD..............................................Straight shank drill....................................... N168
RNMGoooooo.......................Insert (Class M tolerance)........................... A104 SD..............................................Straight shank drill....................................... N170
RN-Soo.....................................Clamp screw................................................ P006 SDoo.........................................Set bolt........................................................ P006
RPMToooo M0E-JS.................Insert (For BRP type cutter)............... K028,L105 SDEN1203AEN..........................Insert (For FMSD type cutter)...................... K028
RPMWoooo M0o....................Insert (For BRP type cutter)............... K028,L105 SDFCR/Looooooo...............SP holder..................................................... P019
RSooooT.................................Clamp screw................................................ P006 SDJCR/Looooooo................SP holder............................................C023,P019
RTGooA...................................Insert (For TL type holder)........ A159,B050,C035 SDJCR/Looooooo -SM.........Small tools holder (External front turning).... D009
SDJER/Looooooo................AL holder..................................................... C032

SDKNooooAEo......................Insert (For FMSD type cutter)...................... K028
So..............................................Clamp screw................................................ P006 SDLS..........................................Straight shank drill....................................... N171
11
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
SDNCNooooooo..................SP holder..................................................... C023 SMGTRoooooooo...............Insert (For SMG holder).....................F124,G025

SDNCR/Looooooo -SM........Small tools holder (External front turning).... D009 SMTTRoooooooo................Insert (For SMT holder)......................F124,G025
SDNENooooooo..................AL holder..................................................... C032 SNo F43B2o..............................Insert (For DN/BN425 type face mill).......... K031
SDXCR/Looooooo...............SP holder..................................................... P019 SNC43B2o................................Insert (For DN/BN425 type face mill).......... K031
SE03-65.....................................Locator screw.............................................. P030 SNGAoooooo........................Insert (Class G tolerance)....................................
SE300 type................................SE300 type face mill.................................... P030
A109,B028,B029,B056
SE300 type................................SE300 type end mill.................................... P033 SNGGoooooo R/L.................Insert (Class G tolerance)........................... A108
SE400 type................................SE400 type face mill.................................... P030 SNGNoooooo........................Insert (Class G tolerance).........A124,B037,B058
SE515Rooooo........................SE515 type face mill.....................................L034 SNGUooooooANo R-o.........Insert (For WSX445 type cutter)......... K031,L013
SEA42C10GR/L.........................Insert (For E404/FE404 type cutter).... K028,L152 SNK43B2o................................Insert (For DN/BN425 type face mill).......... K031
SECNooooAFTN1..................Insert (For SE445/SE545 type cutter)......... K028 SNMAoooooo.......................Insert (Class M tolerance)........................... A109
SECNoooo EFo R1..................Insert (For SE415/SE515 type cutter).................. SNMGoooooo.......................Insert (Class M tolerance)........................... A107
K029,K045,L035 SNMGoooooo -C...................Insert (Class M tolerance)........................... A106
SECN1203AFFR1......................Insert (For SE445 type cutter)..................... K045 SNMGoooooo -FH.................Insert (Class M tolerance)........................... A105
SED2KMG..................................MS end mill................................................... J089 SNMGoooooo -FS.................Insert (Class M tolerance)........................... A105
SED2KPG..................................MS end mill................................................... J088 SNMGoooooo -GH................Insert (Class M tolerance)........................... A109
SEE2L........................................Carbide end mill........................................... J106 SNMGoooooo -GK................Insert (Class M tolerance)........................... A107
SEE4L........................................Carbide end mill........................................... J177 SNMGoooooo -GM................Insert (Class M tolerance)........................... A107
SEENooooAFo N1..................Insert (For SE445/545 type cutter).............. K028 SNMGoooooo -LK.................Insert (Class M tolerance)........................... A105
SEENoooo EFo R1..................Insert (For SE415/515 type cutter)..... K029,L035 SNMGoooooo -LM.................Insert (Class M tolerance)........................... A105
SEERooooAFEN-JS...............Insert (For SE445/545 type cutter).............. K029 SNMGoooooo -LP.................Insert (Class M tolerance)........................... A105
SEER1203EFER-JS..................Insert (For SE415 type cutter)..................... K029 SNMGoooooo -MA................Insert (Class M tolerance)........................... A107
SEET13T3AGEN-JL..................Insert (For ASX445 type cutter).......... K030,L021 SNMGoooooo -MH................Insert (Class M tolerance)........................... A107
SEFooo....................................Setting fixture...............................................L159 SNMGoooooo -MK................Insert (Class M tolerance)........................... A106
SEG4SA.....................................Carbide end mill........................................... J179 SNMGoooooo -MM................Insert (Class M tolerance)........................... A106
SEGT13T3AGFN-JP..................Insert (For ASX445 type cutter).......... K030,L021 SNMGoooooo -MP................Insert (Class M tolerance)........................... A106
SEKNooooAFo N1.................Insert (For SE445/545 type cutter).............. K028 SNMGoooooo -MS................Insert (Class M tolerance)........................... A107
SEKNooooAFTN....................Insert (For SE445/545 type cutter).............. K028 SNMGoooooo R/L-1G...........Insert (Class M tolerance)........................... A106
SEKNoooo EFo R....................Insert (For SE415/515 type cutter).............. K029 SNMGoooooo -RK.................Insert (Class M tolerance)........................... A108
SEKNoooo EFo R1..................Insert (For SE415/515 type cutter)..... K029,L035 SNMGoooooo -RM................Insert (Class M tolerance)........................... A108
SEKN1203AGTN.......................Insert (For corner angle 45 type cutter)..... K030 SNMGoooooo -RP.................Insert (Class M tolerance)........................... A108
SEMT13T3AGSN-FT.................Insert (For ASX445 type cutter).......... K030,L021 SNMGoooooo -RS.................Insert (Class M tolerance)........................... A108
SEMT13T3AGSN-JH.................Insert (For ASX445 type cutter).......... K030,L021 SNMGoooooo -SA.................Insert (Class M tolerance)........................... A105
SEMT13T3AGSN-JM.................Insert (For ASX445 type cutter).......... K030,L021 SNMGoooooo -SH.................Insert (Class M tolerance)........................... A105
SEPDM.......................................HSS milling shank drill................................. N135 SNMGoooooo -SY.................Insert (Class M tolerance)........................... A106
SETHRooooooo...................SET holder.................................................. P021 SNMMoooooo -HV.................Insert (Class M tolerance)........................... A109
SETKoo....................................Clamp bridge............................................... P015 SNMMoooooo -HX.................Insert (Class M tolerance)........................... A109
SETSoo....................................Clamp screw................................................ P006 SNMMoooooo -HZ.................Insert (Class M tolerance)........................... A109
SFAN1203ZFFR/L2...................Insert (For BF407/QBF407 type cutter)....... K030 SNMNoooooo.......................Insert (Class M tolerance).................. A124,K031
SFCN1203ZFFR/L2...................Insert (For BF407/QBF407 type cutter)................ SNMUooooooANER-o.........Insert (For WSX445 type cutter)......... K031,L013
K030,K045 SNTFoooo R............................SNT holder.................................................. P025
SGoo Roooo..........................SG20 type face mill......................................L033 SOET12T308PEER-JL..............Insert (For ASX400 type cutter).......... K031,L043
SHooo -FSDUCLoo................Small tools holders (For opposite tool posts)....... SOGT12T308PEFR-JP..............Insert (For ASX400 type cutter).......... K031,L043
D026 SOMT12T308PEER/L-JM..........Insert (For ASX400 type cutter).......... K032,L043
SHP400 type..............................SHP400 type face mill................................. P030 SOMT12T308PEER-JH.............Insert (For ASX400 type cutter).......... K031,L043
SHP400 type..............................SHP400 type end mill.................................. P033 SOMT12T320PEER-FT.............Insert (For ASX400 type cutter).......... K032,L043
SL32oo -90................................Sleeve (For H100THB32-135)..................... H022 SOMXoooooo -oo................Insert (For MVX type drill)..................K048,N218
SLCSooo.................................Clamp screw................................................ P006 SONX1206PER..........................Insert (For VOX400 type cutter)......... K032,L037
SLCWoo...................................Clamp wedge.............................................. P019 SPCA53Z...................................Insert (For FF3000 type face mill)...... K032,L149
SLNoo.......................................Nut............................................................... P019 SPCG53Z...................................Insert (For FF3000 type face mill)...... K032,L149
SL-ONEN120404ASN................Insert (For AOX445 type cutter)......... K045,L032 SPENoooo EDR......................Insert (For corner angle 15 type cutter)..... K033
SLPoo.......................................Lock pin....................................................... P019 SPENoooA..............................Insert (For FP490/590 type cutter).......................
SLSTNoo..................................Shim............................................................ P019
K032,L150,L151
SMGHRooooooo..................SMG holder........................................F124,G024 SPEN1203EEER/L1...................Insert (For FBP415/QBP415 type cutter).... K033
12
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
SPEN1203EETR1......................Insert (For FBP415/QBP415 type cutter).... K045 SSYPRoo CAoo......................SS type cartridge.........................................M006
SPER1203EEER-JS..................Insert (For FBP415/QBP415 type cutter).... K033 STASXooo N............................Shim............................................................ P012
SPGNoooooo........................Insert (For S400/500 type cutter)......................... STAWo Noooo Soo...............STAW type drill (General use)..................... N220
A160,B051,B068,K033 STAWo Soooo Soo................STAW type drill (General use)..................... N220
SPGRoooooo R.....................Insert (Class G tolerance)........................... A160 STAWKooooTG......................Insert (For STAW type drill)...... K055,N220,N223
SPGXoooooo........................Insert (Class G tolerance).................. A140,B060 STAWNooooT........................Insert (For STAW type drill)...... K054,N220,N223
SPKNoooo EDR......................Insert (For corner angle 15 type cutter)..... K033 STAWNooooTH......................Insert (For STAW type drill)...... K053,N220,N223
SPMB1204APT..........................Insert (For BSP type end mill)..................... K033 STBE445NF...............................Shim............................................................ P028
SPMNoooooo........................Insert (Class M tolerance).................. A160,K033 STBS500N.................................Shim............................................................ P012
SPMNooooooT.....................Insert (Class M tolerance)........................... K033 STFER/Looooooo................AL holder..................................................... C033
SPMRoooooo........................Insert (Class M tolerance)........................... A160 STFPR/Loo CAoo....................SS type cartridge.........................................M006
SPMToooooo........................Insert (Class M tolerance)........................... A140 STGCR/Looooooo...............SP holder..................................................... C027
SPMT120408-A..........................Insert (For TBE1 type end mill)................... K034 STGER/Looooooo...............AL holder..................................................... C033
SPMWoooooo.......................Insert (Class M tolerance)......... A140,K034,L113 STGPRoo CAoo......................SS type cartridge.........................................M006
SPMX120408-oo......................Insert (For SPX type end mill)............ K034,L110 STPMRo N.................................Shim.............................................................L143
SPNN1203EEER/L1..................Insert (For FBP415 type cutter)................... K033 STS1..........................................Clamp screw................................................ P006
SPS1..........................................Locator screw.............................................. P006 STSEooo R/L...........................Shim.............................................................L034
SPSEooo R/L...........................Locator...................................... L034,P030,P033 STSP415R.................................Shim............................................................ P030
SPSEWooo R/L........................Locator........................................................ P030 STTPRoo CAoo.......................SS type cartridge.........................................M006
SPSG20R...................................Locator.........................................................L033 SUFToo Roo............................Insert (For SUF type end mill)............ K036,L126
SPSHP400R/L...........................Locator............................................... P030,P033 SVJBR/Looooooo -SM.........Small tools holder (External front turning).... D010
SPSVN32...................................Shim............................................................ P012 SVJCR/Looooooo................SP holder............................................C028,P019
SPX4-oooA24A058RA............SPX type end mill.........................................L109 SVJDR/Looooooo................AL holder..................................................... C034
SPX4RooooooA058A...........SPX type end mill.........................................L109 SVLPR/Looooooo -SM.........Small tools holder (External front turning).... D010
SPX4Rooooo BT50Noo........SPX type end mill.........................................L108 SVPCR/Looooooo...............SP holder............................................C029,P019
SPX4Rooooo MT5No............SPX type end mill.........................................L108 SVPDR/Looooooo...............AL holder..................................................... P020
SPX4RoooooWNoo.............SPX type end mill.........................................L108 SVPPR/Looooooo -SM.........Small tools holder (External front turning).... D011
SR..............................................HSS end mill................................................. J426 SVVBR/Looooooo -SM.........Small tools holder (External front turning).... D011
SRBToo....................................Insert (For SRF type end mill)............ K034,L122 SVVCNooooooo...................SP holder............................................C028,P019
SRDCNooooooo..................SP holder............................................C025,P019 SVVDNooooooo...................AL holder..................................................... P020
SRE type....................................SRE type end mill........................................ P033 SXZCR/Loooooo15...............Profile holder............................................... C030
SRFHooAMoooo...................SRF type end mill................................L121,L125
SRFHoo Sooo.........................SRF type end mill................................L120,L124
SRFHoo SoooW.....................SRF type end mill (Carbide shank).....L121,L125 TABoooo Soo........................TAB type drill............................................... P037
SRFToo....................................Insert (For SRF type end mill)............ K034,L122 TAFL/M/Soooo Foo...............TAF type drill............................................... N240
SRGoo C...................................Insert (For SRM2 type end mill)... K035,L129,L134 TAGS/Moooo Foo..................TAGS/M type drill........................................ P036
SRGoo E...................................Insert (For SRM2 type end mill)... K035,L129,L134 TASSoooo C/Soo..................TASS type drill............................................. P035
SRGCR/Looooooo...............SP holder............................................C025,P019 TAWo Boooo S32....................TAW type drill (For bridge construction)...... N239
SRK1R.......................................Clamp bridge............................................... P015 TAWo HooooT........................Insert (For TAW type drill)........ K049,K050,N229
SRMoo C-M...............................Insert (For SRM2 type end mill)......... K035,L129
N234,N239
SRMoo E-M...............................Insert (For SRM2 type end mill)......... K035,L129 TAWo Noooo Soo..................TAW type drill (General use)....................... N229
SRM2oooAMoo S/Loo..........SRM2 type end mill......................................L130 TAWKHooooTG.....................Insert (For TAW type drill)........ K051,N229,N236
SRM2ooo M/S/WNLo..............SRM2 type end mill......................................L134 TBE1 type..................................TBE1 type end mill...................................... P034
SRM2ooo Soo........................SRM2 type end mill.............................L128,L129 TBE2 type..................................TBE2 type end mill...................................... P034
SRS5..........................................Clamp screw....................................... P006,P033 TBGNoooooo........................Insert (Class G tolerance)........................... B052
SRSGNooooooo..................SR holder.................................................... P020 TCGNoooooo........................Insert (Class G tolerance)........................... A161
SRSGR/Looooooo...............SR holder.................................................... P020 TCGToooooo -AZ..................Insert (Class G tolerance)........................... A141
SRXCR/Looooooo...............SP holder..................................................... P019 TCGToooooo R/L-F...............Insert (Class G tolerance)........................... A141
SSBCR/L1616H09.....................SP holder..................................................... P019 TCGWoooooo.......................Insert (Class G tolerance)........................... B061
SSE41R/L..................................Locator (For E404 type face mill)................ P028 TCGWoooooo FS..................Insert (Class G tolerance)........................... B045
SSKPRoo CAoo......................SS type cartridge.........................................M006 TCMToooooo........................Insert (Class M tolerance)........................... A142
SSPoo R/L.................................Locator........................................................ P029 TCMToooooo -FM.................Insert (Class M tolerance)........................... A141
SSSCR/Looooooo...............SP holder..................................................... C026 TCMToooooo -FP..................Insert (Class M tolerance)........................... A141
SSSPRoo CAoo......................SS type cartridge.........................................M006 TCMToooooo -FV..................Insert (Class M tolerance)........................... A141
13
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
TCMToooooo -LM.................Insert (Class M tolerance)........................... A142 TNMGoooooo -RK.................Insert (Class M tolerance)........................... A115
TCMToooooo -LP..................Insert (Class M tolerance)........................... A141 TNMGoooooo -RM................Insert (Class M tolerance)........................... A114
TCMToooooo -MK.................Insert (Class M tolerance)........................... A142 TNMGoooooo -RP.................Insert (Class M tolerance)........................... A114
TCMToooooo -MM.................Insert (Class M tolerance)........................... A142 TNMGoooooo -RS.................Insert (Class M tolerance)........................... A115
TCMToooooo -MP.................Insert (Class M tolerance)........................... A142 TNMGoooooo -SA.................Insert (Class M tolerance)........................... A111
TCMWoooooo.......................Insert (Class M tolerance).........A143,B045,B061 TNMGoooooo -SH.................Insert (Class M tolerance)........................... A111
TD...............................................Taper shank drill.......................................... N185 TNMGoooooo -SY.................Insert (Class M tolerance)........................... A111
TECNoooo PEo R1..................Insert (For NSE300/NSE400 type cutter)............. TNMMoooooo -HZ.................Insert (Class M tolerance)........................... A115
K037,K045 TNMNoooooo........................Insert (Class M tolerance)........................... A125
TECN1603PEo1W.....................Insert (For NSE300/SE300 type cutter)....... K037 TNMXoooooo -MW................Insert (Class M tolerance)........................... A113
TEENoooo PEo R1..................Insert (For NSE300/NSE400 type cutter)............. TNMXoooooo -SW.................Insert (Class M tolerance)........................... A111
K036,K037 TNP-CCGWoooooo G2.........Insert (Class G tolerance)........................... B040
TEERoooo PEER-JS...............Insert (For NSE300/400/SE300 type cutter).... K037 TNP-CNGAooooooo2..........Insert (Class G tolerance)........................... B023
TEGXoooooo........................Insert (For AL holder).................................. B066 TNP-DCGWoooooo G2.........Insert (Class G tolerance)........................... B043
TEGXoooooo R/L..................Insert (For AL holder)......................... A144,B066 TNP-DNGAooooooo2..........Insert (Class G tolerance)........................... B026
TEKNoooo PEo R....................Insert (For NSE400/SE400 type cutter)....... K037 TNP-SNGAooooooo2..........Insert (Class G tolerance)........................... B028
TEKNoooo PEo R1..................Insert (For NSE400/SE400 type cutter)....... K037 TNP-TNGAooooooo3..........Insert (Class G tolerance)........................... B031
TIPooo.....................................Wrench........................................................ P002 TNP-VNGAooooooo2..........Insert (Class G tolerance)........................... B032
TKYoo D....................................Driver........................................................... P002 TPENoooo Po R......................Insert (For corner angle 0 type cutter)....... K037
TKYoo F....................................Flag wrench................................................. P002 TPEWooooZPo R2.................Insert (For PMF type end mill).... K037,K046,L142
TKYoo R....................................L-wrench...................................................... P002 TPGHoooooo R/L-FS............Insert (Class G tolerance)........................... A145
TKYooT....................................T-wrench..................................................... P002 TPGNoooooo........................Insert (Class G tolerance).........A162,B052,B068
TKYooW...................................Flag wrench................................................. P002 TPGRoooooo R/L..................Insert (Class G tolerance)........................... A162
TLHRoooo..............................TL holder..................................................... C035 TPGToooooo R/L-F...............Insert (Class G tolerance)........................... B062
TNGAoooooo........................Insert (Class G tolerance).........A115,B031,B056 TPGVoooooo R/L-F...............Insert (Class G tolerance)........................... B063
TNGGoooooo -PK.................Insert (Class G tolerance)........................... A110 TPGXoooooo........................Insert (Class G tolerance).........A147,B047,B063
TNGGoooooo R/L..................Insert (Class G tolerance)........................... A114 TPGXoooooo R/L..................Insert (Class G tolerance)........................... A146
TNGGoooooo R/L-F..............Insert (Class G tolerance)........................... A110 TPKNoooo Po R......................Insert (For corner angle 0 type cutter)....... K037
TNGGoooooo R/L-FS............Insert (Class G tolerance)........................... A110 TPMHoooooo -FV..................Insert (Class M tolerance)........................... A145
TNGGoooooo R/L-K..............Insert (Class G tolerance)........................... A112 TPMHoooooo -MV.................Insert (Class M tolerance)........................... A147
TNGNoooooo........................Insert (Class G tolerance).................. A125,B038 TPMHoooooo -SV..................Insert (Class M tolerance)........................... A146
TNMAoooooo........................Insert (Class M tolerance)........................... A115 TPMNoooooo........................Insert (Class M tolerance).................. A162,K038
TNMGoooooo.......................Insert (Class M tolerance)........................... A113 TPMRoooooo........................Insert (Class M tolerance)........................... A162
TNMGoooooo -C...................Insert (Class M tolerance)........................... A111 TPMXoooooo........................Insert (Class M tolerance)........................... A146
TNMGoooooo -FH.................Insert (Class M tolerance)........................... A110 TPMXoooooo L......................Insert (Class M tolerance)........................... A146
TNMGoooooo -FS.................Insert (Class M tolerance)........................... A110 TPNX1605N...............................Insert (For VIPER type end mill).................. K038
TNMGoooooo -FY.................Insert (Class M tolerance)........................... A110 TPSoo.......................................Clamp screw................................................ P007
TNMGoooooo -GH.................Insert (Class M tolerance)........................... A115 TRM2ooo So............................TRM2 type end mill..................................... P034
TNMGoooooo -GK.................Insert (Class M tolerance)........................... A112 TSo............................................Clamp screw................................................ P007
TNMGoooooo -GM................Insert (Class M tolerance)........................... A112 TSoo.........................................Clamp screw................................................ P007
TNMGoooooo -LK.................Insert (Class M tolerance)........................... A111 TSooo......................................Clamp screw................................................ P007
TNMGoooooo -LM.................Insert (Class M tolerance)........................... A111 TSMPRooo Soo......................TSMP type end mill......................................L136
TNMGoooooo -LP.................Insert (Class M tolerance)........................... A110 TSRooooo S...........................Clamp screw................................................ P008
TNMGoooooo -LS.................Insert (Class M tolerance)........................... A111 TSSooooo..............................Radial screw................................................ P008
TNMGoooooo -MA................Insert (Class M tolerance)........................... A113 TTAHR/Loooo........................Small tools holder (External threading)....... D024
TNMGoooooo -MH................Insert (Class M tolerance)........................... A113 TTATooooooo R/Lo -B.........Insert (For small tools holder)...................... D024
TNMGoooooo -MJ.................Insert (Class M tolerance)........................... A112 TTD.............................................Taper shank drill, For steel frame................ N196
TNMGoooooo -MK................Insert (Class M tolerance)........................... A112
TNMGoooooo -MM................Insert (Class M tolerance)........................... A112
TNMGoooooo -MP.................Insert (Class M tolerance)........................... A112 UCR............................................Clamp bridge............................................... P015

TNMGoooooo -MS.................Insert (Class M tolerance)........................... A113 UGHNooo................................UG holder.....................................................F120
TNMGoooooo R/L-1G...........Insert (Class M tolerance)........................... A111 UGHR/Looooooo.................UG holder.....................................................F121
TNMGoooooo R/L-2G...........Insert (Class M tolerance)........................... A114 UGS1..........................................Wrench.........................................................F121
TNMGoooooo R/L-ES...........Insert (Class M tolerance)........................... A113
14
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
VCGToooooo -AZ..................Insert (Class G tolerance)........................... A151

VCGToooooo R/L-F...............Insert (Class G tolerance)........................... A151
V10000-ooooooo.................V10000 type face mill...................................L147 VCHFRB.....................................MIRACLE end mill........................................ J339

VA2MS.......................................VIOLET end mill........................................... J381 VCHSM.......................................MIRACLE drill, Medium, For hardened material....
VA2SS........................................VIOLET end mill........................................... J380
N128
VA4MC.......................................VIOLET end mill........................................... J400 VCLD..........................................MIRACLE end mill........................................ J188

VAJR..........................................VIOLET end mill........................................... J422 VCMDSC....................................MIRACLE end mill........................................ J164
VALR..........................................VIOLET end mill........................................... J424 VCMH.........................................MIRACLE end mill........................................ J121
VAMFPR....................................VIOLET end mill........................................... J418 VCMHDRB.................................MIRACLE end mill........................................ J342
VAMH.........................................VIOLET end mill........................................... J397 VCMToooooo........................Insert (Class M tolerance)........................... A152
VAMR.........................................VIOLET end mill........................................... J420 VCMToooooo -FM.................Insert (Class M tolerance)........................... A151
VAPDM.......................................VIOLET drill, Medium, High precision......... N142 VCMToooooo -FP..................Insert (Class M tolerance)........................... A151
VAPDMSUS...............................VIOLET drill, Medium, High precision, For stainless steel.... VCMToooooo -FV..................Insert (Class M tolerance)........................... A151
N152 VCMToooooo -LM.................Insert (Class M tolerance)........................... A151
VAPDS.......................................VIOLET drill, Short, High precision.............. N137 VCMToooooo -LP..................Insert (Class M tolerance)........................... A151
VAPDSCB..................................VIOLET drill, Short flute length, High precision, For counter boring.... VCMToooooo -MK.................Insert (Class M tolerance)........................... A152
N159 VCMToooooo -MM................Insert (Class M tolerance)........................... A152
VAPDSSUS................................VIOLET drill, Short, High precision, For stainless steel.... VCMToooooo -MP.................Insert (Class M tolerance)........................... A152
N146 VCMToooooo -MV.................Insert (Class M tolerance)........................... A152
VASFPR.....................................VIOLET end mill........................................... J416 VCMToooooo -SV..................Insert (Class M tolerance)........................... A152
VBEToooooo R/L-SN............Insert (Class E tolerance)............................ A150 VCMWoooooo.......................Insert (Class M tolerance)........................... A152
VBEToooooo R/L-SR............Insert (Class E tolerance)............................ A150 VCPSRB....................................MIRACLE end mill........................................ J292
VBEToooooo R/LW-SN.........Insert (Class E tolerance)............................ A150 VCSFPR.....................................MIRACLE end mill........................................ J202
VBGToooooo R/L-F...............Insert (Class G tolerance)........................... A148 VCSSS.......................................MIRACLE drill, Short, For steel (3mm shank series)....
VBMToooooo........................Insert (Class M tolerance)........................... A149
N127
VBMToooooo -FM.................Insert (Class M tolerance)........................... A148 VCT13R......................................Cartridge (For V10000 type cutter)...............L147
VBMToooooo -FP..................Insert (Class M tolerance)........................... A148 VCXB.........................................MIRACLE end mill........................................ J251
VBMToooooo -FV..................Insert (Class M tolerance)........................... A148 VDGXoooooo R/L..................Insert (Class G tolerance)........................... A153
VBMToooooo -LM.................Insert (Class M tolerance)........................... A148 VDGXoooooo R/L-F..............Insert (Class G tolerance)........................... B067
VBMToooooo -LP..................Insert (Class M tolerance)........................... A148 VF2MD.......................................IMPACT MIRACLE end mill......................... J067
VBMToooooo -MK.................Insert (Class M tolerance)........................... A149 VF2MV.......................................IMPACT MIRACLE end mill......................... J069
VBMToooooo -MM................Insert (Class M tolerance)........................... A149 VF2SB........................................IMPACT MIRACLE end mill......................... J229
VBMToooooo -MP.................Insert (Class M tolerance)........................... A149 VF2SDB.....................................IMPACT MIRACLE end mill......................... J232
VBMToooooo -MV.................Insert (Class M tolerance)........................... A149 VF2SDBL...................................IMPACT MIRACLE end mill......................... J233
VBMToooooo -SV..................Insert (Class M tolerance)........................... A149 VF2SSB.....................................IMPACT MIRACLE end mill......................... J228
VBMWoooooo.......................Insert (Class M tolerance)........................... A150 VF2WB.......................................IMPACT MIRACLE end mill......................... J227
VC2C..........................................MIRACLE end mill........................................ J377 VF2XL........................................IMPACT MIRACLE end mill......................... J071
VC2ESB.....................................MIRACLE end mill........................................ J243 VF2XLB......................................IMPACT MIRACLE end mill......................... J237
VC2JS........................................MIRACLE end mill........................................ J079 VF2XLBS...................................IMPACT MIRACLE end mill......................... J236
VC2MB.......................................MIRACLE end mill........................................ J248 VF3XB........................................IMPACT MIRACLE end mill......................... J271
VC2MDB....................................MIRACLE end mill........................................ J249 VF4MB.......................................IMPACT MIRACLE end mill......................... J281
VC2MS.......................................MIRACLE end mill........................................ J076 VF4MD.......................................IMPACT MIRACLE end mill......................... J143
VC2PSB.....................................MIRACLE end mill........................................ J245 VF4MV.......................................IMPACT MIRACLE end mill......................... J145
VC2PSBP...................................MIRACLE end mill........................................ J246 VF4SVB.....................................IMPACT MIRACLE end mill......................... J279
VC2SS........................................MIRACLE end mill........................................ J074 VF6MHV.....................................IMPACT MIRACLE end mill......................... J183
VC3MB.......................................MIRACLE end mill........................................ J276 VF6MHVCH................................IMPACT MIRACLE end mill......................... J187
VC4JC........................................MIRACLE end mill........................................ J162 VF6MHVRB................................IMPACT MIRACLE end mill......................... J348
VC4JRB.....................................MIRACLE end mill........................................ J337 VF6MHVRBCH...........................IMPACT MIRACLE end mill......................... J353
VC4MB.......................................MIRACLE end mill........................................ J285 VF6SVRCH................................IMPACT MIRACLE end mill......................... J204
VC4MC.......................................MIRACLE end mill........................................ J160 VF8MHVCH................................IMPACT MIRACLE end mill......................... J190
VC4SRB.....................................MIRACLE end mill........................................ J335 VF8MHVRBCH...........................IMPACT MIRACLE end mill......................... J354
VC4STB.....................................MIRACLE end mill........................................ J373 VFFDRB.....................................IMPACT MIRACLE end mill......................... J314
VC6MH.......................................MIRACLE end mill........................................ J189 VFHVRB.....................................IMPACT MIRACLE end mill......................... J315
VC8MH.......................................MIRACLE end mill........................................ J191 VFJHV........................................IMPACT MIRACLE end mill......................... J148
15
INDEX
INDEX

ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
VFMD.........................................IMPACT MIRACLE end mill......................... J185

VFMDRB....................................IMPACT MIRACLE end mill......................... J351
PRODUCT NAME
PAGE
VFMFPR.....................................IMPACT MIRACLE end mill......................... J199 WBGToooooo R/L-F..............Insert (Class G tolerance)........................... A155
VFMHV.......................................IMPACT MIRACLE end mill......................... J146 WBMToooooo R/L-MV..........Insert (Class M tolerance)........................... A155
VFMHVCH..................................IMPACT MIRACLE end mill......................... J150 WCGToooooo R/L.................Insert (Class G tolerance)........................... A156
VFMHVRB..................................IMPACT MIRACLE end mill......................... J325 WCMToooooo.......................Insert (Class M tolerance)........................... A156
VFMHVRBCH.............................IMPACT MIRACLE end mill......................... J327 WCMWoooooo......................Insert (Class M tolerance)........................... B065
VFSD..........................................IMPACT MIRACLE end mill......................... J184 WCSoooooo H.......................Shim screw.................................................. P008
VFSDRB.....................................IMPACT MIRACLE end mill......................... J350 WECooAFo R5C......................Wiper insert (For SE445/545 type cutter).... K042
VFSFPR.....................................IMPACT MIRACLE end mill......................... J197 WECoo EFo R5C......................Wiper insert (For SE415/515 type cutter).............
VFSFPRCH................................IMPACT MIRACLE end mill......................... J201
K042,L035
VFX5-ooooooAooo R..........VFX5 type end mill.......................................L114 WEEW13T3AGo R3C................Wiper insert (For ASX445 type cutter).................
VFX6-oooAooAooo R..........VFX6 type end mill.......................................L117
K047,L021
VIP400 type...............................VIP400 type face mill................................... P030 WEEW13T3AGo R8C................Wiper insert (For ASX445 type cutter).................
VIP445 type...............................VIP445 type face mill................................... P030
K042,L021
VIPER type................................VIPER type end mill.................................... P033 WFC42ZFER2............................Wiper insert (For BF407/QBF407 type cutter)......
VNGAoooooo........................Insert (Class G tolerance).........A118,B033,B057
K047
VNGGoooooo -FJ..................Insert (Class G tolerance)........................... A116 WNEU2006ZEN7C-WK..............Wiper insert (For AHX640W type cutter)..............
VNGGoooooo R/L.................Insert (Class G tolerance)........................... A118
K043,L028,L030
VNGGoooooo R/L-F..............Insert (Class G tolerance)........................... A116 WNEU2007ZEN7C-WP..............Wiper insert (For AHX640S type cutter)...............
VNGMoooooo -MJ.................Insert (Class G tolerance)........................... A117
K043,L028
VNMGoooooo.......................Insert (Class M tolerance)........................... A118 WNGU1406ANEN8C-M.............Wiper insert (For WSX445 type cutter)................
VNMGoooooo -FH.................Insert (Class M tolerance)........................... A116
K043,L013
VNMGoooooo -FS.................Insert (Class M tolerance)........................... A116 WNMAoooooo......................Insert (Class M tolerance)........................... A123

VNMGoooooo -GK................Insert (Class M tolerance)........................... A117 WNMGoooooo......................Insert (Class M tolerance)........................... A122
VNMGoooooo -GM................Insert (Class M tolerance)........................... A117 WNMGoooooo -C..................Insert (Class M tolerance)........................... A120
VNMGoooooo -LK.................Insert (Class M tolerance)........................... A116 WNMGoooooo -FH................Insert (Class M tolerance)........................... A119
VNMGoooooo -LM.................Insert (Class M tolerance)........................... A116 WNMGoooooo -FS................Insert (Class M tolerance)........................... A119
VNMGoooooo -LP.................Insert (Class M tolerance)........................... A116 WNMGoooooo -FY................Insert (Class M tolerance)........................... A119
VNMGoooooo -LS.................Insert (Class M tolerance)........................... A117 WNMGoooooo -GH...............Insert (Class M tolerance)........................... A123
VNMGoooooo -MA................Insert (Class M tolerance)........................... A118 WNMGoooooo -GJ................Insert (Class M tolerance)........................... A123
VNMGoooooo -MH................Insert (Class M tolerance)........................... A118 WNMGoooooo -GK...............Insert (Class M tolerance)........................... A121
VNMGoooooo -MJ.................Insert (Class M tolerance)........................... A117 WNMGoooooo -GM...............Insert (Class M tolerance)........................... A121
VNMGoooooo -MK................Insert (Class M tolerance)........................... A117 WNMGoooooo -LK................Insert (Class M tolerance)........................... A119
VNMGoooooo -MM................Insert (Class M tolerance)........................... A117 WNMGoooooo -LM................Insert (Class M tolerance)........................... A119
VNMGoooooo -MP................Insert (Class M tolerance)........................... A117 WNMGoooooo -LP................Insert (Class M tolerance)........................... A119
VNMGoooooo -MS................Insert (Class M tolerance)........................... A118 WNMGoooooo -LS................Insert (Class M tolerance)........................... A119
VNMGoooooo -SH.................Insert (Class M tolerance)........................... A117 WNMGoooooo -MA...............Insert (Class M tolerance)........................... A121
VOX400-oooooo R................VOX400 type face mill.........................L036,L037 WNMGoooooo -MH...............Insert (Class M tolerance)........................... A121
VOX400Roooooo..................VOX400 type face mill..................................L036 WNMGoooooo -MJ................Insert (Class M tolerance)........................... A120
VPEToooooo R/L-SRF..........Insert (Class E tolerance)............................ A154 WNMGoooooo -MK...............Insert (Class M tolerance)........................... A121
VPGToooooo M-SMG............Insert (Class G tolerance)........................... A154 WNMGoooooo -MM...............Insert (Class M tolerance)........................... A121
VQ4SVB.....................................SMART MIRACLE end mill.......................... J283 WNMGoooooo -MP...............Insert (Class M tolerance)........................... A121
VQJHV.......................................SMART MIRACLE end mill.......................... J155 WNMGoooooo -MS...............Insert (Class M tolerance)........................... A122
VQMHV......................................SMART MIRACLE end mill.......................... J151 WNMGoooooo -MW..............Insert (Class M tolerance)........................... A122
VQMHVRB.................................SMART MIRACLE end mill.......................... J328 WNMGoooooo -RK................Insert (Class M tolerance)........................... A122
VQMHVRBF...............................SMART MIRACLE end mill.......................... J333 WNMGoooooo -RM...............Insert (Class M tolerance)........................... A122
VQMHZV....................................SMART MIRACLE end mill.......................... J112 WNMGoooooo -RP................Insert (Class M tolerance)........................... A122
VQMHZVOH...............................SMART MIRACLE end mill.......................... J118 WNMGoooooo -RS................Insert (Class M tolerance)........................... A123
VQSVR.......................................SMART MIRACLE end mill.......................... J180 WNMGoooooo -SA................Insert (Class M tolerance)........................... A120
VQXL..........................................SMART MIRACLE end mill.......................... J157 WNMGoooooo -SH................Insert (Class M tolerance)........................... A120
VSD............................................VIOLET drill, Straight shank........................ N162 WNMGoooooo -SW...............Insert (Class M tolerance)........................... A120
VSD645 type..............................VSD645 type face mill................................. P030 WNMGoooooo -SY................Insert (Class M tolerance)........................... A120
VTDS..........................................VIOLET drill, Short, Taper shank................ N164
16
INDEX
ORDER NUMBER
PRODUCT NAME
PAGE ORDER NUMBER
PRODUCT NAME
PAGE
WOEW12T308PEoo 8C............Wiper insert (For ASX400 type cutter)................. 2SS.............................................HSS end mill................................................. J383
K043,L043 31-o...........................................31 type brazed tools holder...........................I005
WOEX1206PER5C....................Wiper insert (For VOX400 type cutter)................. 32-o...........................................32 type brazed tools holder...........................I005
K043,L037 33-o...........................................33 type brazed tools holder...........................I005
WPC42EEER/L10C...................Wiper insert (For FBP415/QBP415 type cutter).... 34-o...........................................34 type brazed tools holder...........................I005
K043 35-o...........................................35 type brazed tools holder...........................I005
WPC42W3GR............................Wiper insert (For P425/DP type cutter)....... K043 36-o...........................................36 type brazed tools holder...........................I005
WPGToooooo.......................Insert (Class G tolerance)........................... B065 37-o...........................................37 type brazed tools holder...........................I006
WPGToooooo R/L-FS...........Insert (Class G tolerance)........................... A157 38-o...........................................38 type brazed tools holder...........................I006
WPMToooooo -MV................Insert (Class M tolerance)........................... A157 39-o...........................................39 type brazed tools holder...........................I006
WPSTNoo.................................Shim............................................................ P012 3KD............................................Triangular shank drill, (Type 6.5)(Type 10)(Type 13)....
WPSWC43.................................Shim............................................................ P012
N197
WPSWN43.................................Shim............................................................ P012 40-o...........................................40 type brazed tools holder...........................I006

WSooooooT..........................Clamp screw................................................ P008 41-o...........................................41 type brazed tools holder...........................I006
WSooooooTPS.....................Clamp screw................................................ N228 42-o...........................................42 type brazed tools holder...........................I006
WSoo LH...................................Stopper........................................................ N228 43-o...........................................43 type brazed tools holder...........................I006
WS1............................................Wedge screw............................................... P008 47-o...........................................47 type brazed tools holder...........................I007
WSX445-ooooooo R.............WSX445 type face mill........................L010,L011 49-o...........................................49 type brazed tools holder...........................I007
WSX445Rooooooo..............WSX445 type face mill.................................L010 4LC.............................................HSS end mill................................................. J412
WSX445Roooo SA32M...........WSX445 type end mill..................................L012 4MC............................................HSS end mill................................................. J406
51-o...........................................51 type brazed tools holder...........................I007

95-o...........................................95 type brazed tools holder...........................I007
XCMToooooo -SVX...............Insert (Class M tolerance)........................... A158

XDGT1550PDo R-Goo.............Insert (For BXD type cutter)............... K038,L075
XDGT1550PDFR-GLoo............Insert (For BXD type cutter)............... K038,L075
XDGX1750oo PDo R-GM..........Insert (For AXD4000 type cutter)....... K039,L062
XDGX1750oo PDFR-GL...........Insert (For AXD4000 type cutter)....... K039,L062
XDGX2270oo PDFR-GL...........Insert (For AXD7000 type cutter)....... K039,L068
XNMU160ooo R-o S.................Insert (For VFX5 type cutter).............. K040,L115
XNMU190ooo R-o S.................Insert (For VFX6 type cutter).............. K040,L118
XPGToooo PDo R-Goo..........Insert (For BAP3500 type cutter)................. K041
XPMToooo PDER-Moo..........Insert (For BAP3500 type end mill)............. K041
Z
ZCMXoooooo ER-o...............Insert (For DCCC type end mill).................. K041
ZRooo C...................................C type head (For ZR type end mill)............. P033
ZRoooT....................................T type head (For ZR type end mill).............. P033
ZRMoooo R-Mo......................Insert (For BAP300 type end mill)............... K041
NUMBEROTHERS
01-o...........................................Insert (For brazed tools holder).....................I002
09E1...........................................Insert (For brazed tools holder).....................I003
1LA.............................................HSS end mill................................................. J379
1MA............................................HSS end mill................................................. J378
2LS.............................................HSS end mill................................................. J391
2MK............................................HSS end mill................................................. J394
2MS............................................HSS end mill................................................. J389
17
SAFETY OF CUTTING TOOL PRODUCTS

y 1. Use of Cutting Tool Products
Packages of Mitsubishi products carry a safety warning label. However, tools are not labeled with detailed warning
indications. Please read the "Safety of Cutting Tool Products" in this catalogue before handling cutting tool
products and cemented carbide materials. Moreover, as a part of your workers' safety education, please notify
the contents of the "Safety of Cutting Tool Products" to all workers.
y 2. Basic Characteristics of Hard Tool Materials

a In Terms of "Safety of Cutting Tool Products"
Hard Tool Materials : General term for tool materials like cemented carbide alloy, cermet, ceramics,

sintered CBN, sintered diamond, high speed steel and alloy steel, etc.
a Physical Characteristics
Appearance : Varies depending on the type of material. Eg. grey, black, gold, etc.
: None
Smell
Hardness, Specific Gravity :
Hard Tool Materials
Hardness (HV)
Specific Gravity
Hard Tool Materials
Hardness (HV)
Specific Gravity
High Speed Steel (HSS)
200 1200kg/mm
79
Sintered CBN
2000 5000kg/mm
35
Cemented Carbide
500 3000kg/mm2
9 16
Sintered Diamond
8000 12000kg/mm2
35
Cermet
500 3000kg/mm
59
Alloy Steel
200 1200kg/mm
79
1000 4000kg/mm2
27
Diamond Electroforming Product
8000 12000kg/mm2
35
Ceramics
a Constituents
Carbide, nitride, carbon nitride, oxide, such as W, Ti, Al, Si, Ta, B, V and metals such as Fe, Co, Ni, Cr, Mo.
y 3. Safety of Cutting Tool Products

uHard tool materials have a large specific gravity. Thus, they require special attention as heavy materials when the size or
quantity is large.
uCutting tool products generate dust and mist during grinding operations or heating. This dust and mist can be harmful when
coming in contact with the eyes or skin, or if substantial quantities are swallowed. When grinding and machining, it is
recommended to use local exhaust ventilation and respirators, a dust protective mask, glasses, gloves etc. If dust makes
contact with the hands, thoroughly wash the affected area with soap and water. Don't eat in the exposed area, and wash
hands thoroughly before eating. Remove dust from the clothing by a cleaning or washing, but don't shake off.
uCobalt and nickel contained in carbide or other cutting tool materials are reported as possibly carcinogenic to humans. It is
also reported that cobalt and nickel dust and mist can affect the skin, respiratory organs and heart through repeated or
prolonged contact.
uFor further information, please refer to MSDS (Material Safety Data Sheet).
MSDS=Material Safety Data Sheet

Home page: http://www.mitsubishicarbide.com/msds/
y 4. Handling Cutting Tool Products

uSurface conditions affect toughness of cutting tools. Therefore, use a diamond grinding wheel for finishing.
uHard tool materials are extremely hard and brittle at the same time. Thus, they may be broken by shocks and
tightening with excess force.
uHard tool materials and ferrous materials have different thermal expansion ratios. Shrinkage or swell fit products
may suffer from cracks when applied temperature is higher or lower than the appropriate temperature for the
tool.
uPay special attention on storing hard tool materials. Toughness of hard tool materials is lowered when they
corrode due to coolant and other liquid.
uWhen brazing hard tool materials, if the temperature is too high or too low from the melting point of the brazing
material, loosening and breakage may occur.
uAfter regrinding cutting tools, make sure that there are no cracks.
uMachining hard tool materials on EDM may cause cracks on the surface due to electrons remaining after the
EDM operation, resulting in lowering of the toughness. Eliminate these cracks by grinding, etc.
18
SUGGESTIONS ON HOW TO USE CUTTING TOOLS

Products
All Cutting Tools
Indexable Inserts
Type Tools
Cutters and Other

Rotating Tools
Hazard
eCutting tools have sharp cutting edges. Handling them
with bare hands may cause injuries.
ake precautions such as wearing gloves especially

*Twhen
handling tools and during installation.
eImproper use of tools and application of inappropriate

cutting conditions may cause the tool to break and be
expelled from the machine providing risk of injury.
safety guards and goggles are used.

*ERnsure
to handling explanatory notes and catalogues.
*.Uefer
se tools under recommended cutting conditions.
eImpact load and rapid increase of cutting resistance due

to excessive wear may cause the tool to break and be
expelled from the machine providing risk of injury.

*EEnsure
xchange tools before excessive wear occurs.
*
eCutting tools and workpieces become extremely hot

during cutting. Touching them with bare hands may
cause burns.
*Take precautions such as wearing gloves.
eExpelled hot chips produced in cutting produces risk of

injuries and burns.

*EDnsure
uring swarf removal and machine cleaning ensure the
*machine
is stopped and wear gloves. Please use tools,
Brazed Tools
Others
such as cutting nippers and cutting clippers.
eIn cutting, sparks, hot chips and heat generation caused

by tool breakage provides a risk of igniting a fire.
void using cutting tools in places where there is a

*Apossibility
of igniting a fire.
In case of using non-water soluble oil, make sure to

*have a fire prevention countermeasure.
eUsing machines, chucks, and tools with poor balance at

high revolutions may cause tools to break providing risk
of injuries.

*ECnsure
heck the machine for vibration, chattering, and
*abnormal
noise.
eHandling machined parts with burrs using bare hands

may cause injuries.
*Wear gloves.
eIf inserts and spare parts are not held securely, they may
become loose and be expelled producing risk of injuries.
lean insert locating seat and spare parts before

*Csetting
inserts.
se the tool provided for setting inserts, and ensure the
*Uinserts
and spare parts are clamped securely. Do not
use the tool provided for things other than prescribed
inserts and spare parts.
eClamping inserts and spare parts too tightly by using

tools such as extension pipes may cause them to break
and be expelled.
use extra tools for more leverage. Only use

*Dtheo not
tool provided.
eWhen applying high cutting speed, spare parts and

inserts may be expelled due to centrifugal force.
Pay special attention on each safety guidline.
efer to the handling explanatory notes and

*Rcatalogues.
Use tools under recommended cutting
eMilling cutters have sharp edges.

Handling them with bare hands may cause injuries.
*Take precautions such as wearing gloves.

pply cutting speed within the range of recommended
*Acutting
conditions.
Adjust accuracy and balance of spindles and

*bearings periodically to prevent off center revolving
ePoor balance or off center revolving of tools may cause

vibration and chattering which could cause the tool to
break and be expelled.
Drilling Tools
Countermeasure
conditions.
and chattering caused by wear on these parts.
eThrough cutting in cases when the workpiece revolves

may produce a disk shaped peice with sharp edges
when the cutting tool breaks through.
nsure safety guards and goggles are used.

* EAlso
install a cover on the chuck.
eDrills with an extremely small diameter have a very

sharp point which may puncture the skin if not handled
carefully. If the drill breaks during cutting, the broken
pieces may be expelled.
andle with care. Take precautions such as wearing

*Hgloves
and goggles.
eWeakening of the braze and breakage of inserts may

cause injury.
using them, ensure they are brazed securely.

*BDefore
o not use them under conditions which produce very
*high temperature.
eMachine and tools may be damaged if they are used for

purposes other than the prescribed application.
*Use them strictly for the prescribed application.
INFORMATION
This catalogue completes the basic precautions for safety use of our company's products.
For further information, please refer to the guideline, catalogs or contact us. We are not responsible for any accidents causing by modifying
tools without our permission.
19
HOW TO READ THE STANDARD

OF TURNING INSERTS
a How this section page is organized
a Graph of chip control by work material
z Organized according to turning insert shape.

(Refer to the index on the next page.)
x Inserts are arranged in order of :
Negative inserts (with hole|without hole)
Positive inserts (with hole|without hole)
c Breakers are arranged in order of :
Finish Cutting|Light Cutting|Medium Cutting
|Rough Cutting|Heavy Cutting
Shows recommended chip breakers and chip control range

according to work material and cutting application.
Graphs are colored according to cutting applications
(Finish|Light|Medium|Rough|Heavy)
and contain recommended breakers for each application.
Finish Cutting :
Light Cutting :
Rough Cutting :
Heavy Cutting :
Medium Cutting :
GRADE APPLICATION RECOMMENDED

FOR EACH WORK MATERIAL
cutting conditions suitable for each type of work material
is shown as a general guide to select the grade.
: Stable Cutting : General Cutting : Unstable Cutting
SHAPE & ANGLE

MARK
INDICATION OF NEGATIVE/
POSITIVE TYPE
TITLE OF PRODUCT
ACCORDING TO THE
INSERT TYPE
PRODUCT
SECTION
STOCK STATUS
INSERT GRADES
INSERT
NUMBER
6
FY
4
SY
2
1
0.1
0.3
0.5
0.7
FH
LP
4
3
RP
2
1
0
MP
0.1
Feed (mm/rev)
WITH
HOLE
0.3
0.5
6
5
4
3
2
Feed (mm/rev)
MW
1
0
0.7
SW
0.1
0.3
0.5
0.7
Feed (mm/rev)
Work
Material
P
M
K
N
S
RM
5
4
3
2
1
0
LM
0.1
0.3
0.5
RK
Flat Top
6
4
3
1
Feed (mm/rev)
0.3
Coated
Cermet Cermet
LK
CNMG120404-LK
CNMG120408-LK
CNMG120412-LK
0.4
0.8
a a
1.2
a a
CNMG120404-LS
CNMG120408-LS
0.4
0.8
CNMG09T304-SH
CNMG09T308-SH
CNMG120404-SH
CNMG120408-SH
CNMG120412-SH
CNMG120404-SA
CNMG120408-SA
CNMG120412-SA
0.4
0.8
0.7
Cast Iron
NEW
Carbide
C008
C009
E013
E036
E040
H006
008
a a
Light Cutting
Non-ferrous Metal
NEW

Coated
Cermet Cermet
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
RE
(mm)
Carbide
a [
a a a
a [
a a
0.8
a a
CNMG120404-FS
CNMG120408-FS
0.4
0.8
CNMG120404-FY
CNMG120408-FY
0.4
0.8
a a
CNGG1204V5-FJ
CNGG120401-FJ
CNGG120402-FJ
CNGG120404-FJ
CNGG120408-FJ
CNGG120404-PK
0.05
0.1
0.2
0.4
0.8
a a
CNMG120404-LP
CNMG120408-LP
CNMG120412-LP
0.4
0.8
a a
a a
a a
a a
1.2
a a
a a
CNMG120404-LM
CNMG120408-LM
CNMG120412-LM
0.4
0.8
a a a
1.2
a a a
1.2
C008
C009
E013
E036
E040
H006
008
Finish Cutting
a
C008
C009
E013
E036
E040
H006
008
Finish Cutting
C008
C009
E013
E036
E040
H006
008
Finish Cutting
a a
0.4
a
a
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
Finish Cutting
Light Cutting
LM
RE
(mm)
Stainless Steel
0.2
0.4
LP
Order Number
Steel
Order Number
PK
Non-ferrous Metal
Shape
: Unstable Cutting
CNMG120402-FH
CNMG120404-FH
CNMG120408-FH
CNMG120412-FH
Finish Cutting
0.5
Feed (mm/rev)
: General Cutting
FH
FJ
Cast Iron
MK
0.1
: Unstable Cutting
Stainless Steel
Coated
: General Cutting
Steel
LK
Shape
FY
P
M
K
N
S
0.7
: Stable Cutting
Coated
FS
Work
Material

8
MM
: Stable Cutting

Heavy Cutting
a a a
Light Cutting
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
LS
a a
a a
Light Cutting
SH
Light Cutting
SA
SW
a a [ a a
a a
0.8
1.2
a a [ a a
a a
0.4
0.8
a a [ a a
a a [ a a
1.2
a a [ a a
CNMG120404-SW
CNMG120408-SW
CNMG120412-SW
0.4
0.8
a a
a a
a a a
a a
a a
a a a
1.2
a a
CNMG120404-SY
CNMG120408-SY
0.4
0.8
CNMG120404-C
CNMG120408-C
0.4
0.8
CNMG120404-MJ
CNMG120408-MJ
CNMG120412-MJ
CNMG120416-MJ
0.4
0.8
a a
a a
1.2
a a
1.6
a a
CNGG120404-MJ
CNGG120408-MJ
0.4
0.8
a a [ a a
C008
C009
E013
E036
E040
H006
008
[[
C008
C009
E013
E036
E040
H006
008
[[
Light Cutting
MJ
a a
a a
a a
a a
C008
C009
E013
E036
E040
H006
008
Light Cutting
=
CHIP BREAKERS

a
A092
C008
C009
E013
E036
E040
H006
008
Light Cutting
MJ
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
a a a
Light Cutting
WITH
HOLE
C008
C009
E013
E036
E040
H006
008
Light Cutting
(Wiper)
SY
NEG
C008
C009
E013
E036
E040
H006
008
0.4
Light Cutting
TURNING INSERTS
HX
Rough Cutting
Applicable
Holder Page

Medium Cutting
Applicable
Holder Page
P Carbon Steel Alloy Steel (Wiper)

Depth of Cut (mm)
Size
Light Cutting
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
P Carbon Steel Alloy Steel (180280HB)
Mild Steel
Finish Cutting
Depth of Cut (mm)

P
CNMG 12 04 02- FH
TYPE INSERTS
WITH HOLE
Depth of Cut (mm)
CN
Depth of Cut (mm)
NEG
80
Depth of Cut (mm)
TURNING INSERTS
GRADES
IDENTIFICATION
A042
A030
A002
A093
LEGEND FOR STOCK STATUS MARK

is shown on the left hand page of
each double-page spread.
CUTTING APPLICATION
is shown in order of: Finish|Light
|Medium|Rough|Heavy.
PHOTO OF INSERT
INDICATION OF CHIPBREAKER
indicates the designation
for a chipbreaker.
PAGE REFERENCE
CHIP BREAKERS
GRADES
TECHNICAL DATA
indicates reference pages, on the right hand page of
APPLICABLE HOLDER PAGE

indicates reference pages for details of applicable holders.
INSERT CORNER RADIUS (RE)

a To Order : Please specify
zinsert number and xgrade.
A000
TURNING TOOLS
INSERT STANDARDS
INSERT GRADES
INDENTIFICATION .................................................. A002
HOLE GEOMETRY .................................................. A004
PRECISION BREAKER STANDARD ...................... A006
.................................. A009
OUTLINE OF
CLASSIFICATION OF GRADES AND CHIP BREAKERS FOR TURNING ... A010
PRECISION BREAKER SYSTEM ........................... A026
WIPER INSERT........................................................ A028
GRADES FOR TURNING ........................................ A030
TURNING APPLICATION RANGE .......................... A031
COATED CARBIDE (CVD) ...................................... A034
COATED CARBIDE (PVD) ...................................... A036
CERMET .................................................................. A037
COATED CERMET .................................................. A038
CEMENTED CARBIDE ............................................ A039
MICRO-GRAIN CEMENTED CARBIDE .................. A040
CLASSIFICATION OF INSERTS ............................. A042
RECOMMENDED CUTTING CONDITIONS ............ A070
STANDARD OF INSERTS
CNppTYPE...RHOMBIC 80 ........... A092
DNppTYPE...RHOMBIC 55 ........... A098
RNppTYPE...ROUND .................. A104

TN ppTYPE...TRIANGULAR 60 ...... A110
VNppTYPE...RHOMBIC 35 ........... A116
WNppTYPE...TRIGON 80 ............. A119

TNppTYPE...TRIANGULAR 60 ...... A125
CC ppTYPE...RHOMBIC 80 ........... A126
CPppTYPE...RHOMBIC 80 ........... A131
DC ppTYPE...RHOMBIC 55 ........... A132

DEppTYPE...RHOMBIC 55 ........... A136
RC ppTYPE...ROUND .................. A137
SCppTYPE...SQUARE 90 ............ A138

TE ppTYPE...TRIANGULAR 60 ...... A144
VBppTYPE...RHOMBIC 35 ........... A148
VCppTYPE...RHOMBIC 35 ........... A151
VDppTYPE...RHOMBIC 35 ........... A153
VP ppTYPE...RHOMBIC 35 ........... A154
WBppTYPE...TRIGON 80 ............. A155
WCppTYPE...TRIGON 80 ............. A156
WPppTYPE...TRIGON 80 ............. A157
XCppTYPE...RHOMBIC 25 ........... A158
RTG TYPE................................. A159

A001
IDENTIFICATION
M
TURNING INSERTS
TURNING INSERTS
Symbol
Insert Shape
Hexagonal
Octagonal
Pentagonal
Square
Triangular
Rhombic 80
Rhombic 55
Rhombic 75
Rhombic 50
Rhombic 86
Rhombic 35
Trigon
Rectangular
Parallelogram 85
Parallelogram 82
Parallelogram 55
Round
Special Design
Triangular insert with a facet

(Secondary Cutting Edge)
IC
IC
c Tolerance Class
Symbol
A
F
C
H
E
G
J
K
L
M
N
U
*
*
*
*
*
Tolerance of
Nose Height
M (mm)
Tolerance of
Inscribed Circle
IC (mm)
Tolerance of
Thickness
S (mm)
e0.005
e0.025
e0.025
e0.005
e0.013
e0.025
e0.013
e0.025
e0.025
e0.013
e0.013
e0.025
e0.025
e0.025
e0.025
e0.025
e0.025
e0.13
e0.005
e0.05 e0.15
e0.025
e0.013
e0.05 e0.15
e0.025
e0.025
e0.05 e0.15
e0.025
e0.08 e0.18
e0.05 e0.15
e0.13
e0.08 e0.18
e0.05 e0.15
e0.025
e0.13 e0.38
e0.08 e0.25
e0.13
The surface of insert with
Detail of M Class Insert Tolerance

aTolerance of Nose Height M (mm)
Rhombic Rhombic Round
D.I.C. Triangular Square Rhombic
80
55
35
6.35 e0.08 e0.08 e0.08 e0.11 e0.16
9.525 e0.08 e0.08 e0.08 e0.11 e0.16
e0.13 e0.13 e0.13 e0.15
15.875 e0.15 e0.15 e0.15 e0.18
e0.15 e0.15 e0.15 e0.18
12.70
19.05
25.40
31.75
e0.20
aTolerance of Inscribed Circle IC (mm)

80
55
35
6.35 e0.05 e0.05 e0.05 e0.05 e0.05
9.525 e0.05 e0.05 e0.05 e0.05 e0.05 e0.05

e0.08 e0.08 e0.08 e0.08
15.875 e0.10 e0.10 e0.10 e0.10
e0.08
e0.10
e0.10 e0.10 e0.10 e0.10
e0.10
12.70
* mark is sintered.
19.05
z Insert Shape
e0.18
25.40
e0.13
e0.13
31.75
e0.15
e0.15
c Tolerance Class
C N M G
x
x Normal Clearance
Symbol
Metric
Hole
Configuration
W With Hole Cylindrical Hole
With Hole
15
With Hole Cylindrical Hole
20
With Hole
25
30
With Hole
11
With Hole
Other Normal Clearance
Major Normal Clearance
A002
v Fixing and/or for Chip Breaker
Normal Clearance
Symbol
Hole
One Countersink
(40 60)
Double Countersink
(40 60)
One Countersink
(70 90)
Double Countersink
(70 90)
Chip
Breaker
Figure
Symbol
Hole
Hole
Configuration
Chip
Breaker
No
No
One
Sided
Single
Sided
No
Double
Sided
Double
Sided
Without
Hole
No
No
Without
Hole
Single
Sided
One
Sided
Without
Hole
Double
Sided
No
Double
Sided
Figure
Special Design
02
TURNING INSERTS
Symbol
Diameter of
Inscribed Circle
(mm)
04
03
03
06
3.97
L3
08
05
04
04
08
4.76
03
09
06
05
05
09
5.56
06
is from the bottom of the insert

*Thickness
to the top of the cutting edge.
Symbol
Thickness (mm)
S1
1.39
6.35
01
1.59
7.94
T0
1.79
8.00
02
2.38
9.525
T2
2.78
03
3.18
T3
3.97
04
4.76
06
6.35
19.05
07
7.94
20.00
09
9.52
6.00
04
11
07
06
06
11
05
13
09
08
07
13
06
16
11
09
09
16
08
09
10
10.00
12
12.00
12
08
15
10
22
15
12
12
22
12.70
19
16
15
27
15.875
16
16.00
19
13
23
19
19
33
27
22
22
38
25
31
25
25
44
25.40
31
38
32
31
54
31.75
20
25
n Insert Thickness
22.225
25.00
32
32.00
/ Chip Breaker
b Insert Size
Symbol
Corner Radius (mm)
Figure
Cutting Edge
00
Sharp Nose
0.03
V5
0.05
01
0.1
Round
02
0.2
Cutting Edges
04
0.4
0.8
12
1.2
16
1.6
20
2.0
24
2.4
28
2.8
32
3.2
00 : Inch
M0 : Metric
RP
LM
MM
RM
LK
MK
RK
LS
MS
RS
FP
LP
MP
MA
SW
MW
HZ
HX
HV
, Cutting Edge Condition
V3
08
MP
12 04 08 (E) (N) - MP
m Insert Corner Configuration
LP
Symbol
Sharp
Cutting Edges
Chamfered
Cutting Edges
. Cutting Direction
Figure
Hand Symbol
Right R
Left
Neutral N
Chamfered
and Rounded
Cutting Edges
Mitsubishi Materials omit

the honing symbol.
Round Insert
(Refer to JIS-B4120-1998)
A003
NEGATIVE
Type C
Dimensions (mm)
DNGA
DNGG
DNGM
DNMA
DNMG
DNMM
DNMX
SNGA
SNGG
SNMA
SNMG
SNMM
TNGA
TNGG
TNMA
TNMG
TNMM
TNMX
VNGA
VNGM
VNGG
VNMG
VNMM
WNMA
WNMG
RNMG
RNMA
D1
D1
FHCSA
FHCSD
D1
Dimensions (mm)
Hole Type
Insert Number
D1 FHCSD FHCSA
()
Hole Type
0903pp
3.81
0904pp
3.81
1204pp
5.16
1606pp
6.35
1906pp
7.93
2509pp
9.12
CCET
CCGB
CCMB
CCGH
CCMH
0602pp
2.8
3.8
09T3pp
4.4
6.0
0602pp
2.8
3.9
1104pp
3.81
03S1pp
2.0
2.9
1504pp
5.16
04T0pp
2.4
3.5
1506pp
5.16
0602pp
2.8
3.8
09T3pp
4.4
6.0
CCGT
CCMT
1204pp
5.5
7.5
0602pp
2.8
3.8
0803pp
3.4
4.5
09T3pp
4.4
6.0
0903pp
3.81
1204pp
5.16
1204pp
5.5
7.5
1506pp
6.35
03S1pp
2.0
2.9
1906pp
7.93
04T0pp
2.4
3.5
0602pp
2.8
3.8
09T3pp
4.4
6.0
2507pp
9.12
2509pp
9.12
CCGW
CCMW
1103pp
2.26
1204pp
5.5
7.5
1603pp
3.81
0802pp
3.4
4.5
1604pp
3.81
2204pp
5.16
2706pp
6.35
3309pp
7.93
1604pp
3.81
CPGT
0903pp
4.4
6.0
0802pp
3.5
5.3
78
0903pp
4.5
6.3
78
0802pp
3.5
5.6
78
0903pp
4.6
6.6
80
DCET
DCGT
0702pp
2.8
3.8
11T3pp
4.4
6.0
0702pp
2.8
3.8
11T3pp
4.4
6.0
1504pp
5.5
7.5
CPGB
CPMB
CPMH
CPMX
0603pp
3.81
06T3pp
3.81
DCGW
DCMW
DCMT
0604pp
3.81
DEGX
1504pp
5.1
7.0
85
0804pp
5.16
1003M0
3.6
4.6
21
090300
3.81
1204M0
4.2
5.4
21
120400
5.16
1606M0
5.2
6.7
21
150600
6.35
2006M0
6.5
8.0
21
190600
7.93
2507M0
7.2
9.1
21
9.12
3209M0
9.5
11.7
21
250900
310900
A004
FHCSA
FHCSD
D1
POSITIVE
Insert Number
CNGA
CNGG
CNMA
CNMG
CNMM
CNMP
Type D
Type B
FHCSD
HOLE GEOMETRY
Type A
D1
TURNING INSERTS
TURNING INSERTS
12.7
RCMX
Type C
Type D
D1
FHCSA
FHCSD
D1
FHCSA
FHCSD
D1
FHCSD
D1
POSITIVE
Dimensions (mm)
Insert Number
D1 FHCSD FHCSA
( )
Dimensions (mm)
Hole Type
Insert Number
RCGT
RCMT
SCMT
SCMW
SPMW
SPMT
SPGX
TCGT
TCMT
TCGW
TCMW
TEGX
TPGX
TPMX
D1 FHCSD FHCSA
()
Hole Type
0602M0
2.8
3.8
VBET
VBGT
VBMT
VBGW
1103pp
2.9
3.8
0803M0
3.4
4.5
10T3M0
4.4
6.0
1604pp
4.4
6.0
09T3pp
4.4
6.0
1204pp
5.5
7.5
0802pp
2.4
3.2
1103pp
2.8
3.8
1604pp
4.4
6.0
VCGT
VCMT
VCGW
VCMW
0903pp
4.6
6.0
1203pp
5.7
7.5
0903pp
4.4
6.0
2205pp
7.5
5.5
1203pp
5.5
7.5
0903pp
4.8
6.4
VDGX
1603pp
4.5
6.1
88
58
WBGT
WBMT
0201pp
2.3
3.2
L302pp
2.3
3.2
WCGT
WCMT
WCGW
WCMW
0201pp
2.3
3.0
L302pp
2.3
3.0
0402pp
2.8
3.8
06T3pp
4.4
6.0
1203pp
5.9
7.7
58
0601pp
2.3
3.2
0802pp
2.3
3.0
0902pp
2.5
3.3
1102pp
2.8
3.8
1303pp
3.4
4.5
2.8
3.8
16T3pp
4.4
6.0
WPGT
WPMT
0402pp
0603pp
4.4
6.0
1603pp
4.4
6.1
88
XCMT
1503pp
2.8
3.8
0802pp
2.5
3.8
88
0902pp
3.0
4.3
88
1103pp
3.5
4.8
88
1603pp
4.8
6.5
58
0802pp
2.7
3.8
88
0902pp
3.2
4.3
88
1103pp
3.7
4.8
88
1603pp
4.8
6.4
58
TPGB
TPMB
TPGH
TPMH
0802pp
2.4
4.0
78
0902pp
2.9
4.3
78
1103pp
3.4
4.8
78
1603pp
4.4
6.5
78
TPGT
1603pp
4.4
6.0
0902pp
2.8
3.8
1103pp
3.4
4.5
TPGV
TURNING INSERTS
Type B
R
Type A
A005
TURNING INSERTS
TURNING INSERTS
PRECISION BREAKER SYSTEM

STANDARD OF INSERTS WITH HAND OF TOOL
a NEGATIVE INSERTS
Unit : mm
Insert Number
Geometry
LBB
GAN
LBB
LE
GAN
B12
DNGG150404R/L
2.8
15
DNGG150408R/L
2.8
15
SNGG090304R/L
1.8
1.6
15
SNGG090308R/L
1.8
1.6
15
SNGG120404R/L
2.3
3.7
15
SNGG120408R/L
2.3
3.7
15
Right hand insert shown.
LBB
GAN
LE
GAN
LB
LBB
B12
TNGG 160402R/L-FS
1.3
15
30
TNGG 160404R/L-FS
1.3
15
30
TNGG 160408R/L-FS
1.3
15
30
TNGG 160402R/L-F
2.5
15
30
TNGG 160404R/L-F
2.5
15
30
TNGG 160408R/L-F
2.5
15
30
TNGG 160402R/L-K
1.5
7.1
15
TNGG 160404R/L-K
1.5
5.4
15
GAN
LB
LBB
B12

LBB
GAN
LE
LBB
GAN
LE
LBB
GAN
A006
TNGG 110302R/L
1.3
3.2
15
TNGG 110304R/L
1.3
3.0
15
TNGG 110308R/L
1.3
2.7
15
TNGG 160304R/L
2.3
5.4
15
TNGG 160402R/L
1.3
8.7
15
TNGG 160404R/L
2.3
5.4
15
TNGG 160408R/L
2.3
5.1
15
TNGG 220404R/L
2.8
9.4
15
TNGG 220408R/L
2.8
9.1
15
VNGG160404R/L
1.8
15
VNGG160408R
1.8
15
Unit : mm
LB
1.2
1.4
LBB
15
2.5
2.5
2.5
2.5
3.7
3.7
3.7
3.7
1.0
1.0
1.0
1.0
1.0
1.5
1.5
1.5
1.5
1.5
1.0
1.5
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.5
1.5
1.5
1.5
2.8
2.8
3.5
3.5
3.5
6.5
6.5
6.5
3.5
3.5
3.5
6.5
6.5
6.5
6.5
LB
20
DCET 0702V3R/L-SR
DCET 070201R/L-SR
DCET 070202R/L-SR
LBB
DCET 070204R/L-SR
DCET 11T3V3R/L-SR
30
20
DCET 11T301R/L-SR
DCET 11T302R/L-SR
Right hand insert shown. DCET 11T304R/L-SR
DCET 070200R/L-SN
DCET 0702V3R/L-SN
DCET 070201R/L-SN
DCET 070202R/L-SN
LBB
DCET 070204R/L-SN
DCET 11T300R/L-SN
20
DCET 11T3V3R/L-SN
DCET 11T301R/L-SN
DCET 11T302R/L-SN
Right hand insert shown. DCET 11T304R/L-SN
DCET 0702V3R/LW-SN
DCET 11T3V3R/LW-SN
LBB
20
CCGH060202R/L-F
CCGH060204R/L-F
1.0
1.4

LBB
CPMH 080204R/L-F
CPMH 090304R/L-F
2.2
2.2
2.2
2.2
3.2
3.2
3.2
3.2
1.0
1.0
1.0
1.0
1.0
1.5
1.5
1.5
1.5
1.5
1.0
1.5
LBB LE
LB
CCET0602V3R/L-SR
CCET060201R/L-SR
CCET060202R/L-SR
LBB
CCET060204R/L-SR
CCET09T3V3R/L-SR
30
20
CCET09T301R/L-SR
CCET09T302R/L-SR
Right hand insert shown. CCET09T304R/L-SR
CCET060200R/L-SN
CCET0602V3R/L-SN
CCET060201R/L-SN
CCET060202R/L-SN
LBB
CCET060204R/L-SN
CCET09T300R/L-SN
20
CCET09T3V3R/L-SN
CCET09T301R/L-SN
CCET09T302R/L-SN
Right hand insert shown. CCET09T304R/L-SN
CCET 0602V3R/LW-SN
CCET 09T3V3R/LW-SN
LBB
Insert Number
Geometry
LBB LE
Insert Number
LB
Geometry
TURNING INSERTS
a POSITIVE INSERTS
20
20
LE
LB
B
LE
15
0.8
0.8
0.8
0.8
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.5
1.5
1.5
1.5
0.6
0.8
0.8
3.0
3.0
3.0
5.0
5.0
5.0
3.0
3.0
3.0
5.0
5.0
5.0
5.0
LBB
LB
CCGT03S1V3L-F
CCGT03S101L-F
35
CCGT03S102L-F
LBB
CCGT03S104L-F
CCGT04T0V3L-F
17 LBB
CCGT04T001L-F
CCGT04T002L-F
Left hand insert shown. CCGT04T004L-F
CCGT0602V3R/L-SS
CCGT060201R/L-SS
LBB
CCGT060202R/L-SS
CCGT09T3V3R/L-SS
14
CCGT09T301R/L-SS
Right hand insert shown. CCGT09T302R/L-SS
CCGT0602V3R-SN
CCGT060201R/L-SN
CCGT060202R/L-SN
LBB
CCGT09T3V3R/L-SN
20
CCGT09T301R/L-SN
CCGT09T302R/L-SN
Right hand insert shown. CCGT09T304R/L-SN
CPGT080204R/L-F
CPGT090302R/L-F
LBB
CPGT090304R/L-F

B
15
* 17
DCGT11T3pptype
20
DCGT 070202R/L-F
DCGT 070204R/L-F
DCGT 11T302R/L-F
DCGT 11T304R/L-F
: 14
LE
LE
DCGT 0702V3R/L-SS
DCGT 070201R/L-SS
LBB
DCGT 070202R/L-SS
DCGT 11T3V3R-SS
14
DCGT 11T301R-SS
Right hand insert shown. DCGT 11T302R-SS
DCGT 0702V3R-SN
DCGT 070201R-SN
DCGT 070202R/L-SN
LBB
DCGT 11T3V3R/L-SN
20
DCGT 11T301R/L-SN
DCGT 11T302R/L-SN
Right hand insert shown. DCGT 11T304R/L-SN
DEGX 150402R/L
LBB
DEGX 150404R/L
20
20
A007

STANDARD OF INSERTS WITH HAND OF TOOL
a POSITIVE INSERTS
Unit : mm
DEGX 150402R/L-F
DEGX 150404R/L-F
2.5
2.5
Geometry
25
Insert Number
1.0
1.0
1.5
1.5
VBET 1103V3R/L-SR
VBET 110301R/L-SR
VBET 110302R/L-SR
VBET 110304R/L-SR
2.5
2.5
2.5
2.5
VBET 110300R/L-SN
VBET 1103V3R/L-SN
VBET 110301R/L-SN
20
VBET 110302R/L-SN
Right hand insert shown. VBET 110304R/L-SN
VBET1103V3R/LW-SN
1.0
1.0
1.0
1.0
1.0
1.0
VCGT 080202R/L-F
VCGT 080204R/L-F
0.8
0.8
VDGX 160302R/L
VDGX 160304R/L
2.0
2.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
13
20
20
SPGR090304R
1.8
1.6
LBB
LB
LBB
15
30
LB
B
14
20
TCGT 0601V3L-F
TCGT 060101L-F
TCGT 060102R/L-F
TCGT 060104R/L-F
1.0
1.0
1.0
1.0
TEGX 160302R/L
TEGX 160304R/L
2.0
2.0
6.0
6.0
Left hand insert shown.

LBB
LBB
20
20
LB
B
TPGX 080202R/L
TPGX 080204R/L
TPGX 090202R/L
LBB
TPGX 090204R/L
TPGX 090208R/L
10
20
TPGX 110302L
TPGX 110304R/L
Right hand insert shown. TPGX 110308R/L
1.3
1.3
1.6
1.6
1.4
1.8
1.8
1.8
15
LBB
LB
3.0
5.4
5.1
13
20

LBB
LB
0.9
0.9
1.0
1.0
1.4
1.4
2.0
2.0
1.3
2.3
2.3
25
20
WBGT0201V3L-F
WBGT020101L-F
WBGT020102L-F
LBB
WBGT020104L-F
WBGTL302V3L-F
13
30
WBGTL30201L-F
WBGTL30202R/L-F
Right hand insert shown. WBGTL30204R/L-F
WCGT 020102R/L
WCGT 020104R/L
LBB
WCGT L30202L
15
30 WCGT L30204L
B
LB
TPGH 080202R/L-FS
TPGH 080204R/L-FS
TPGH 090202R/L-FS
LBB
TPGH 090204R/L-FS
TPGH 110302R/L-FS
20
* 15
TPGH 110304R/L-FS
TPGH1603pptype : 14 TPGH 160304R/L-FS
Right hand insert shown. TPGH 160308R/L-FS
TPGR 110304R/L
TPGR 160304R/L
LBB
TPGR 160308R/L
LB
LE
LE
LBB
LBB
20
LB
B
LE
LBB LE
VBGT 110302R/L-F
VBGT 110304R/L-F
VBGT 160402R/L-F
VBGT 160404R/L-F
LBB
LB
LBB
LBB LE
Insert Number
LB
Geometry
TURNING INSERTS
TURNING INSERTS
WPGT040204R/L-FS
WPGT060304R/L-FS
LB
B
LBB
15
20
A008
supports our customers with information and suitable cutting conditions for each work material by selecting an optimal
indexable insert together with the optional tool.
y LABEL INDICATION
CNMG432MP
z
x
c
vc 310 - 190 m/min

1015 - 625 SFM
f 0.16 - 0.50 mm/rev
0.006 - 0.020 IPR
MADE IN JAPAN
CNMG120408-MP
CNMG120408-MP MC6025
z Work materials
CNMG432MP
MC6025
QU691NZ1AM3B9
P : Steel (Material reference : Carbon steel, alloy steel 180HB)

M : Stainless steel (Material reference : Austenitic stainless steel 180HB)
K : Cast iron (Material reference : Gray cast iron, ductile cast iron 180HB)
N : Aluminium alloy, non-ferrous metal
S : Material reference : Titanium alloy 320HB, Ni, Co-Based Alloy 400HB
H : Hardened steel 60HRC
above is an example. There may be inserts recommended for multiple work materials.
*12 The
Please contact us for recommended cutting conditions using
* coefficient values other than the above.
c Feed rate
x CUTTING SPEED STANDARDS

Work
Material
S
H
*
*
Minimum and maximum feed rate settings are based on the

chip control range of the chip breaker.
Tool Life
Work Material
Hardness
Life
Performance
Carbon steel, alloy steel 180HB
90min
15min
90min
15min
Stainless steel
180HB
90min
15min
Cast iron
180HB
Titanium alloy
320HB
25min
5min
Ni, Co-Based alloy
400HB
80min
10min
Hardened steel
HRC60
P
M
K
TURNING INSERTS
y OUTLINE
3. N :Life based on each grade. For stable choose the performance cutting speed and for unstable choose the tool life feed rate.
4. The tool life is based on the following (VB wear). Some materials include elements other than this.
PMKS VB=0.3mm
H
VB=0.1mm
y TOOL LIFE
Cutting speed has a large affect on tool life.

is based on Taylor's equation (relationship vc Tn=C between tool grade, cutting conditions,
and tool life). Therefore, performance speed and tool life is found for each work material. When the customer requires a different tool life, obtain
coefficient values of the grade you use from the charts below. Multiply the coefficient values by the cutting speed to calculate a new cutting speed.
a P Grade (Steel) cutting speed coefficient values. a K Grade (Cast lron) cutting speed coefficient values.
Tool life
Tool life
15min
30min
45min
60min
90min
15min
30min
45min
60min
90min
UE6105
1.00
0.79
0.69
0.63
0.55
MC5005
1.00
0.83
0.75
0.70
0.63
MC6015
1.00
0.82
0.72
0.67
0.59
MC5015
1.00
0.83
0.75
0.69
0.62
MC6025
1.00
0.83
0.75
0.69
0.62
UE6035
1.00
0.88
0.82
0.78
0.73
MP3025
1.00
0.85
0.77
0.72
0.65
NX2525
1.00
0.87
0.80
0.76
0.70
Grade
Grade
(ex.) Medium cutting of steel

: MC6025
The 1st recommendation
: CNMG120408-MP
Indexable inserts
Recommended cutting speed : vc=310m/min
(Tool life : 15min.)
a M Grade (Stainless Steel) cutting speed coefficient values.

Tool life
15min
30min
45min
60min
90min
MC7015
1.00
0.83
0.75
0.70
0.63
MC7025
1.00
0.90
0.84
0.80
0.75
MP7035
1.00
0.84
0.76
0.71
0.62
1.00
0.78
0.68
0.61
0.53
Grade
aUS735
Tool life required by the customer : 30min.

3100.83i257m/min
y HARDNESS OF THE WORK MATERIAL

Hardness of the work material also affects tool life. Mitsubishi's
suggests cutting speed variations when hardness
differs. Obtain the suitable coefficient value for each type of work material from the chart below. Multiply the coefficient value by the
recommended cutting speed of the grade you use to calculate a new cutting speed.
Work material
P
M
K
(Hardness of workpiece)
Soft
Hard
120HB
140HB
160HB
180HB
200HB
220HB
240HB
260HB
280HB
300HB
320HB
340HB
1.34
1.41
1.27
1.19
1.23
1.19
1.08
1.10
1.09
1.00
1.00
1.00
0.92
0.91
0.97
0.85
0.85
0.91
0.80
0.78
0.88
0.75
0.72
0.85
0.71
0.68
0.81
0.68
0.64
0.78
0.64
0.61
0.75
0.61
0.58
0.72
A009
TURNING INSERTS
TURNING INSERTS
OPTIMUM GRADES AND CHIP BREAKERS FOR EXTERNAL TURNING

a Selection of optimum inserts for turning
The following diagrams show for each type of work material, the optimal combination of suitable grades and
chip breakers for each application area in turning.
y CUTTING CONDITIONS
Continuous Cutting
Constant Depth of Cut
Pre-Machined
Securely Clamped Component Cutting
Stable Cutting
General Cutting
Unstable Cutting
Heavy Interrupted Cutting

Irregular Depth of Cut
Low Clamping Rigidity Cutting
Finish Cutting
FY
Finish Cutting
Light Cutting
Medium Cutting
Rough Cutting
Heavy Cutting
SY
VP25N
FY
SY
MP3025
MP3025
FY
SY
UE6020
UE6020
Mild Steel (Ex : SS400, S10C)
vc : Cutting Speed
f : Feed
ap : Depth of Cut
NEGATIVE INSERTS
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
A010
F
L
M
R
H
Light Cutting
VP25N
y CUTTING AREA
F
L
F
L
F
L
Chip Breaker
Grade
1st Recommendation
vc (m/min)
f (mm/rev)
285 445
0.09 0.23
ap (mm)
0.20 0.80
FY
VP25N
SY
VP25N
260 405
0.16 0.33
0.50 1.20
FY
MP3025
275 420
0.09 0.23
0.20 0.80
SY
MP3025
250 385
0.16 0.33
0.50 1.20
FY
UE6020
285 460
0.09 0.23
0.20 0.80
SY
UE6020
260 420
0.16 0.33
0.50 1.20
General Cutting
Unstable Cutting
Finish Cutting
Light Cutting
FH
LP
AP25N
UE6105
FH
LP
MP3025
MC6015
FH
LP
UE6110
MC6025
Medium Cutting
MP
Light Cutting
Medium Cutting
Rough Cutting
Heavy Cutting
Heavy Cutting
RP
UE6105
HX
UE6105
MP
MC6015
MP
Rough Cutting
Finish Cutting
MC6025
UE6110
RP
HX
MC6015
UE6020
RP
HX
MC6025
UH6400
Carbon Steel Alloy Steel (Ex : S45C, SCM440)
vc : Cutting Speed
f : Feed
ap : Depth of Cut
NEGATIVE INSERTS
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
L
M
R
H
F
L
M
R
H
F
L
M
R
H
TURNING INSERTS
F
L
M
R
H
Stable Cutting
1st Recommendation
vc (m/min)
f (mm/rev)
215 340
0.08 0.20
ap (mm)
Chip Breaker
Grade
FH
AP25N
LP
UE6105
220 405
0.10 0.40
0.30 2.00
MP
UE6105
200 370
0.16 0.50
0.30 4.00
RP
UE6105
190 350
0.25 0.60
1.50 6.00
HX
UE6110
160 275
0.50 1.26
3.00 11.00
FH
MP3025
210 325
0.08 0.20
0.20 1.00
LP
MC6015
210 355
0.10 0.40
0.30 2.00
MP
MC6015
190 325
0.16 0.50
0.30 4.00
RP
MC6015
180 310
0.25 0.60
1.50 6.00
HX
UE6020
155 250
0.50 1.26
3.00 11.00
FH
UE6110
230 390
0.08 0.20
0.20 1.00
LP
MC6025
210 340
0.10 0.40
0.30 2.00
MP
MC6025
190 310
0.16 0.50
0.30 4.00
RP
MC6025
180 295
0.25 0.60
1.50 6.00
HX
UH6400
135 195
0.50 1.26
3.00 11.00
0.20 1.00
CLASSIFICATION
A042
A011
TURNING INSERTS
TURNING INSERTS

L
M
R
Stable Cutting
General Cutting
Unstable Cutting
Light Cutting
LM
MC7015
LM
MC7025
LM
MP7035
MM
MC7015
MM
MC7025
MM
MP7035
Medium Cutting
Rough Cutting
Rough Cutting
RM
MC7015
RM
MC7025
RM
MP7035
Stainless Steel (Ex : SUS304, SUS316)
vc : Cutting Speed
f : Feed
ap : Depth of Cut
NEGATIVE INSERTS
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
A012
Medium Cutting
Light Cutting
L
M
R
L
M
R
L
M
R
LM
1st Recommendation
vc (m/min)
f (mm/rev)
180 285
0.10 0.30
MC7015
0.30 2.00
MM
MC7015
160 255
0.15 0.45
0.70 5.00
RM
MC7015
155 245
0.25 0.55
1.50 6.00
Chip Breaker
Grade
ap (mm)
LM
MC7025
160 215
0.10 0.30
0.30 2.00
MM
MC7025
145 195
0.15 0.45
0.70 5.00
RM
MC7025
140 185
0.25 0.55
1.50 6.00
LM
MP7035
95 155
0.10 0.30
0.30 2.00
MM
MP7035
85 140
0.15 0.45
0.70 5.00
RM
MP7035
85 135
0.25 0.55
1.50 6.00
General Cutting
Unstable Cutting
Light Cutting
LK
MC5005
LK
MC5015
LK
MC5015
Medium Cutting
MK
MC5005
MK
MC5015
MK
MC5015
Light Cutting
Medium Cutting
Rough Cutting
Heavy Cutting
Rough Cutting
Heavy Cutting
RK
Flat Top
MC5005
MC5005
RK
Flat Top
MC5015
MC5015
RK
Flat Top
MC5015
MC5015
Cast Iron Ductile Cast Iron (Ex : FC300)
vc : Cutting Speed
f : Feed
ap : Depth of Cut
NEGATIVE INSERTS
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
L
M
R
H
L
M
R
H
L
M
R
H
LK
1st Recommendation
vc (m/min)
f (mm/rev)
235 375
0.10 0.40
MC5005
0.30 2.00
MK
MC5005
210 335
0.20 0.55
1.00 4.00
RK
MC5005
195 315
0.25 0.60
1.50 6.00
Flat Top
MC5005
195 315
0.20 0.60
2.50 6.00
LK
MC5015
205 335
0.10 0.40
0.30 2.00
MK
MC5015
190 305
0.20 0.55
1.00 4.00
RK
MC5015
180 285
0.25 0.60
1.50 6.00
Flat Top
MC5015
180 285
0.20 0.60
2.50 6.00
LK
MC5015
205 335
0.10 0.40
0.30 2.00
MK
MC5015
190 305
0.20 0.55
1.50 4.00
RK
MC5015
180 285
0.25 0.60
1.50 6.00
Flat Top
MC5015
180 285
0.20 0.60
2.50 6.00
Chip Breaker
TURNING INSERTS
L
M
R
H
Stable Cutting
ap (mm)
Grade
CLASSIFICATION
A042
A013
TURNING INSERTS
TURNING INSERTS

F
L
M
R
Stable Cutting
General Cutting
Unstable Cutting
Finish Cutting
Light Cutting
FJ
LS
RT9010
MT9015
FJ
LS
RT9010
MT9015
MJ
FJ
RT9010
RT9010
MS
MT9015
MS
MT9015
MS
RT9010
Light Cutting
Medium Cutting
Rough Cutting
Rough Cutting
RS
MT9015
RS
MT9015
GJ
RT9010
Titanium Alloy (Ex : Ti-6AI-4V)
vc : Cutting Speed
f : Feed
ap : Depth of Cut
NEGATIVE INSERTS
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
A014
Medium Cutting
Finish Cutting
F
L
M
R
F
L
M
R
F
L
M
R
FJ
1st Recommendation
vc (m/min)
f (mm/rev)
45 95
0.07 0.20
RT9010
0.10 1.00
Chip Breaker
Grade
ap (mm)
LS
MT9015
40 85
0.10 0.25
0.20 0.80
MS
MT9015
40 80
0.10 0.25
0.50 4.00
RS
MT9015
35 75
0.20 0.35
1.00 4.00
FJ
RT9010
45 95
0.07 0.20
0.10 1.00
LS
MT9015
40 85
0.10 0.25
0.20 0.80
MS
MT9015
40 80
0.10 0.25
0.50 4.00
RS
MT9015
35 75
0.200.35
1.00 4.00
FJ
RT9010
45 95
0.07 0.20
0.10 1.00
MJ
RT9010
40 80
0.07 0.25
0.40 1.50
MS
RT9010
40 80
0.10 0.25
0.50 4.00
GJ
RT9010
35 75
0.16 0.35
1.00 3.00
General Cutting
Unstable Cutting
Finish Cutting
Light Cutting
FJ
LS
VP10RT
MP9005
FJ
LS
VP10RT
MP9015
MJ
FJ
VP15TF
VP15TF
Medium Cutting
MS
MP9005
MS
MP9015
MS
VP15TF
Finish Cutting
Light Cutting
Medium Cutting
Rough Cutting
Rough Cutting
RS
MP9015
RS
MP9015
GJ
VP15TF
Ni, Co-Based Alloy (Ex : Inconel718)
vc : Cutting Speed
f : Feed
ap : Depth of Cut
NEGATIVE INSERTS
Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
L
M
R
F
L
M
R
F
L
M
R
FJ
1st Recommendation
vc (m/min)
f (mm/rev)
30 60
0.07 0.20
VP10RT
0.10 1.00
Chip Breaker
TURNING INSERTS
F
L
M
R
Stable Cutting
ap (mm)
Grade
LS
MP9005
30 110
0.10 0.25
0.20 0.80
MS
MP9005
30 100
0.10 0.25
0.50 4.00
RS
MP9015
20 75
0.20 0.35
1.00 4.00
FJ
VP10RT
30 60
0.07 0.20
0.10 1.00
LS
MP9015
25 85
0.10 0.25
0.20 0.80
MS
MP9015
25 80
0.10 0.25
0.50 4.00
RS
MP9015
20 75
0.20 0.35
1.00 4.00
FJ
VP15TF
20 40
0.07 0.20
0.10 1.00
MJ
VP15TF
20 35
0.07 0.25
0.40 1.50
MS
VP15TF
20 35
0.10 0.25
0.50 4.00
GJ
VP15TF
15 30
0.16 0.35
1.00 3.00
CLASSIFICATION
A042
A015
TURNING INSERTS
TURNING INSERTS

Finish Cutting
Light Cutting
FP
LP
NX2525
NX2525
FP
LP
MC6015
MC6015
FP
LP
MC6025
MC6025
Stable Cutting
General Cutting
MP
Unstable Cutting
NX2525
F
L
M
MP
Finish Cutting
Light Cutting
Medium Cutting
MC6015
MP
MC6025
vc : Cutting Speed
f : Feed
ap : Depth of Cut
7POSITIVE INSERTS WITH HOLE

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
A016
Medium Cutting
F
L
M
F
L
M
F
L
M
FP
1st Recommendation
vc (m/min)
f (mm/rev)
225 320
0.04 0.20
NX2525
0.20 0.90
Chip Breaker
Grade
ap (mm)
LP
NX2525
225 320
0.06 0.25
0.20 1.00
MP
NX2525
185 265
0.08 0.30
0.30 2.00
FP
MC6015
250 425
0.04 0.20
0.20 0.90
LP
MC6015
250 425
0.06 0.25
0.20 1.00
MP
MC6015
205 350
0.08 0.30
0.30 2.00
FP
MC6025
250 405
0.04 0.20
0.20 0.90
LP
MC6025
250 405
0.06 0.25
0.20 1.00
MP
MC6025
205 335
0.08 0.30
0.30 2.00
Light Cutting
FP
LP
NX2525
NX2525
FP
LP
MC6015
MC6015
FP
LP
MC6025
MC6025
Medium Cutting
Stable Cutting
General Cutting
MP
Unstable Cutting
NX2525
F
L
M
MP
Finish Cutting
Light Cutting
Medium Cutting
MC6015
MP
MC6025
vc : Cutting Speed
f : Feed
ap : Depth of Cut

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
L
M
F
L
M
F
L
M
FP
1st Recommendation
vc (m/min)
f (mm/rev)
165 235
0.04 0.20
NX2525
0.20 0.90
Chip Breaker
TURNING INSERTS
Finish Cutting
ap (mm)
Grade
LP
NX2525
165 235
0.06 0.25
0.20 1.00
MP
NX2525
135 195
0.08 0.30
0.30 2.00
FP
MC6015
185 310
0.04 0.20
0.20 0.90
LP
MC6015
185 310
0.06 0.25
0.20 1.00
MP
MC6015
150 260
0.08 0.30
0.30 2.00
FP
MC6025
185 295
0.04 0.20
0.20 0.90
LP
MC6025
185 295
0.06 0.25
0.20 1.00
MP
MC6025
150 245
0.08 0.30
0.30 2.00
CLASSIFICATION
A054
A017
TURNING INSERTS
TURNING INSERTS

Finish Cutting
Light Cutting
FM
LM
VP15TF
MC7025
FM
LM
VP15TF
MC7025
FM
LM
VP15TF
MP7035
Stable Cutting
General Cutting
MM
Unstable Cutting
MC7025
F
L
M
MM
Finish Cutting
Light Cutting
Medium Cutting
MC7025
MM
MP7035
Stainless Steel (Ex : SUS304, SUS316)
vc : Cutting Speed
f : Feed
ap : Depth of Cut

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
A018
Medium Cutting
F
L
M
F
L
M
F
L
M
FM
1st Recommendation
vc (m/min)
f (mm/rev)
75 125
0.04 0.20
VP15TF
Chip Breaker
Grade
ap (mm)
0.20 0.90
LM
MC7025
140 190
0.06 0.25
0.20 1.00
MM
MC7025
115 155
0.08 0.30
0.30 2.00
FM
VP15TF
75 125
0.04 0.20
0.20 0.90
LM
MC7025
140 190
0.06 0.25
0.20 1.00
MM
MC7025
115 155
0.08 0.30
0.30 2.00
FM
VP15TF
75 125
0.04 0.20
0.20 0.90
LM
MP7035
85 135
0.06 0.25
0.20 1.00
MM
MP7035
70 115
0.08 0.30
0.30 2.00
MK
MC5005
Medium Cutting
MK
Flat Top
MC5005
MK
MC5015
MK
MC5015
Light Cutting
General Cutting
Unstable Cutting
MC5005
MK
Flat Top
MC5015
MC5015
MK
Flat Top
MC5015
Stable Cutting
F
L
M
Finish Cutting
Light Cutting
Medium Cutting
MC5015
vc : Cutting Speed
f : Feed
ap : Depth of Cut

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
L
M
F
L
M
F
L
M
MK
1st Recommendation
vc (m/min)
f (mm/rev)
170 270
0.08 0.30
MC5005
0.30 2.00
MK
MC5005
170 270
0.08 0.30
0.30 2.00
Flat Top
MC5005
170 270
0.08 0.30
0.30 2.00
MK
MC5015
155 245
0.08 0.30
0.30 2.00
MK
MC5015
155 245
0.08 0.30
0.30 2.00
Flat Top
MC5015
155 245
0.08 0.30
0.30 2.00
MK
MC5015
155 245
0.08 0.30
0.30 2.00
MK
MC5015
155 245
0.08 0.30
0.30 2.00
Flat Top
MC5015
155 245
0.08 0.30
0.30 2.00
Chip Breaker
TURNING INSERTS
Finish Cutting
ap (mm)
Grade
CLASSIFICATION
A054
A019
TURNING INSERTS
TURNING INSERTS

Finish Cutting
Stable Cutting
General Cutting
AZ
Unstable Cutting
HTi10
Finish Cutting
AZ
HTi10
AZ
HTi10
Aluminium Alloy (Ex : A6061, A7075)

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
A020
vc : Cutting Speed
f : Feed
ap : Depth of Cut
F
F
F
1st Recommendation
vc (m/min)
f (mm/rev)
300 700
0.10 0.40
ap (mm)
Chip Breaker
Grade
AZ
HTi10
AZ
HTi10
300 700
0.10 0.40
0.20 3.00
AZ
HTi10
300 700
0.10 0.40
0.20 3.00
0.20 3.00
Stable Cutting
TURNING INSERTS
Finish Cutting
General Cutting
FJ
Unstable Cutting
RT9010
Finish Cutting
FJ
RT9010
FJ
RT9010
Titanium Alloy (Ex : Ti-6AI-4V)
vc : Cutting Speed
f : Feed
ap : Depth of Cut

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
F
F
FJ
1st Recommendation
vc (m/min)
f (mm/rev)
30 75
0.04 0.12
RT9010
0.20 1.40
FJ
RT9010
30 75
0.04 0.12
0.20 1.40
FJ
RT9010
30 75
0.04 0.12
0.20 1.40
Chip Breaker
ap (mm)
Grade
CLASSIFICATION
A054
A021
TURNING INSERTS
TURNING INSERTS

Finish Cutting
Stable Cutting
FJ
VP10RT
General Cutting
Unstable Cutting
Finish Cutting
FJ
VP10RT
FJ
VP10RT
Ni, Co-Based Alloy (Ex : Inconel718)

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
A022
vc : Cutting Speed
f : Feed
ap : Depth of Cut
F
F
F
FJ
1st Recommendation
vc (m/min)
f (mm/rev)
20 45
0.04 0.12
VP10RT
0.20 1.40
FJ
VP10RT
20 45
0.04 0.12
0.20 1.40
FJ
VP10RT
20 45
0.04 0.12
0.20 1.40
Chip Breaker
Grade
ap (mm)
Light Cutting
Medium Cutting
R-R/L
NX2525
Standard
Standard
NX2525
NX2525
R
-25
R/L
R-R/L
NX2525
Standard
Standard
UE6110
UE
UE61
6110
6
10
UE6110
UE
UE61
6110
6
10
R-R/L
UTi20T
Standard
Standard
UE6020
UE6020
Stable Cutting
General Cutting
Unstable Cutting
F
L
M
Finish Cutting
Light Cutting
Medium Cutting
vc : Cutting Speed
f : Feed
ap : Depth of Cut
11POSITIVE INSERTS WITHOUT HOLE

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
L
M
F
L
M
F
L
M
R-R/L
1st Recommendation
vc (m/min)
f (mm/rev)
225 320
0.05 0.12
NX2525
0.20 0.60
Standard
NX2525
185 265
0.08 0.30
0.30 2.00
Standard
NX2525
185 265
0.08 0.30
0.30 2.00
R-R/L
NX2525
225 320
0.05 0.12
0.20 0.60
Standard
UE6110
205 350
0.08 0.30
0.30 2.00
Chip Breaker
TURNING INSERTS
Finish Cutting
Grade
ap (mm)
Standard
UE6110
205 350
0.08 0.30
0.30 2.00
R-R/L
UTi20T
115 165
0.05 0.12
0.20 0.60
Standard
UE6020
195 320
0.08 0.30
0.30 2.00
Standard
UE6020
195 320
0.08 0.30
0.30 2.00
CLASSIFICATION
A054, A062
A023
TURNING INSERTS
TURNING INSERTS
Finish Cutting
Light Cutting
Medium Cutting
R-R/L
NX2525
Standard
Standard
NX2525
NX2525
R
-25
R/L
R-R/L
NX2525
Standard
Standard
UE6110
UE
UE61
6110
6
10
UE6110
UE
UE61
6110
6
10
R-R/L
UTi20T
Standard
Standard
UE6020
UE6020
General Cutting
Unstable Cutting
F
L
M
Finish Cutting
Light Cutting
Medium Cutting
vc : Cutting Speed
f : Feed
ap : Depth of Cut

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
A024
Stable Cutting
F
L
M
F
L
M
F
L
M
R-R/L
1st Recommendation
vc (m/min)
f (mm/rev)
165 235
0.05 0.12
NX2525
0.20 0.60
Standard
NX2525
135 195
0.08 0.30
0.30 2.00
Standard
NX2525
135 195
0.08 0.30
0.30 2.00
Chip Breaker
Grade
ap (mm)
R-R/L
NX2525
165 235
0.05 0.12
0.20 0.60
Standard
UE6110
150 260
0.08 0.30
0.30 2.00
Standard
UE6110
150 260
0.08 0.30
0.30 2.00
R-R/L
UTi20T
85 120
0.05 0.12
0.20 0.60
Standard
UE6020
145 235
0.08 0.30
0.30 2.00
Standard
UE6020
145 235
0.08 0.30
0.30 2.00
Light Cutting
Medium Cutting
R-R/L
NX2525
Flat Top
Flat Top
UC5105
UC5105
R
-R
R/L
R-R/L
NX2525
25
Flat Top
Flat Top
UC5115
5
UC5115
5
R-R/L
UTi20T
Flat Top
Flat Top
VP15TF
VP15TF
Stable Cutting
General Cutting
Unstable Cutting
F
L
M
Finish Cutting
Light Cutting
Medium Cutting
vc : Cutting Speed
f : Feed
ap : Depth of Cut

Cutting Area
Stable Cutting
General Cutting
Unstable Cutting
F
L
M
F
L
M
F
L
M
R-R/L
1st Recommendation
vc (m/min)
f (mm/rev)
150 205
0.05 0.12
NX2525
0.20 0.60
Flat Top
UC5105
135 250
0.08 0.30
0.30 2.00
Flat Top
UC5105
135 250
0.08 0.30
0.30 2.00
R-R/L
NX2525
150 205
0.05 0.12
0.20 0.60
Flat Top
UC5115
130 245
0.08 0.30
0.30 2.00
Chip Breaker
TURNING INSERTS
Finish Cutting
ap (mm)
Grade
Flat Top
UC5115
130 245
0.08 0.30
0.30 2.00
R-R/L
UTi20T
80 115
0.05 0.12
0.20 0.60
Flat Top
VP15TF
115 160
0.08 0.30
0.30 2.00
Flat Top
VP15TF
115 160
0.08 0.30
0.30 2.00
CLASSIFICATION
A062
A025

ANGULAR AND PARALLEL CHIP BREAKER
y CHIP CONTROL RANGE
3-D CHIP BREAKER

Carbon Steel Alloy Steel

Stainless Steel
SN
SS
R/L
Breaker
Breaker
Depth of Cut (mm)
Depth of Cut (mm)
Breaker
SR

Stainless Steel
Difficult-to-Cut Materials
Standard
Breaker
F
Breaker
FS
Breaker
Standard
SMG
Depth of Cut (mm)
TURNING INSERTS
TURNING INSERTS
MV
Breaker
Breaker
SV
FV
Breaker
Breaker
Feed (mm/rev)
MJ
Breaker
FJ
Breaker
Feed (mm/rev)
Feed (mm/rev)
y FEATURES OF CHIP BREAKER

Breaker
Features
CCGH/CCGT CCMH/CCMT
CPMH/CPMT
Type
Type
DCMT
Type
DCGT
Type
TCGT/TCMT
Type
TPMH
Type
VBGT/VBMT
Type
VCMT
Type
WBMT/WCGT
Type
a For medium cutting.
SMG a 3D moulded chipbreaker

provides good chip control.
(G class) a G class insert gives sharp cutting action,
allowing high precision machining.

a Sharp cutting edge and low
resistance design achieves
FV
excellent cutting performance.
(M class) a Suitable for low depths of cut
and low feed rates.
a For light cutting.
SV
a A peninsular dot ensures chip
(M class) control at depths of cut under
1mm.
a A positive insert and the large rake angle
achieve sharp cutting edge performance.

MV
a The double breakers and round-shaped
(M class) dots in the rake face achieve a wide
range of chip discharge.

a For medium cutting.
Standard a Balance of edge strength and
sharpness due to a
(M class) combination of a flat land and
large rake angle.
a The curved edge allows
smooth chip discharge.
a The large rake angle highly
FJ
suitable for finishing
a The curved edge allows
smooth chip discharge.
a Large rake angle highly suitable for
MJ
finish-light cutting difficult-to-cut
materials.
Breaker
FS
Features
a For precision finishing.
a Small width lead breaker for
excellent chip control.
a Sharp cutting edge gives a
CCGH/CCGT
Type
CPGT
Type
DCGT
Type
TPGH
Type
TPGV/TPGT
Type
TCGT
Type
VBGT/VCGT
Type
WBGT
Type
WCGT
Type
WPGT
Type
good surface finish.
a For finish cutting.

a Lead breaker controls chip flow.
R/L
Standard
Breaker
a Lead breaker for light cutting.

a Good chip control for low to
medium feed rates.

a For light cutting.
a Good chip control for low to
medium feed rates.
Features
CCET Type
CCGT Type
DCET Type
DCGT Type
VBET Type
a The wide lead breaker for medium
SR
cutting is suitable for automatic

lathe machining.
a The insert design for low
resistance controls chip flow.
a The parallel breaker for light
SS
cutting is suitable for automatic

lathe machining.
a Excellent chip control at low
feed rates.
a The parallel breaker for general
SN
purpose is suitable for automatic

lathe machining.
a Excellent chip control for low to
medium feed rates.
A026
TURNING INSERTS
ANGULAR AND PARALLEL CHIP BREAKERS (NEGATIVE INSERTS)

y FEATURES OF CHIP BREAKER

Breaker
Depth of Cut (mm)
R/L
FS
Breaker
Breaker
Breaker
a For precision finishing.

a Small width lead breaker
for good chip control.
DNGG
Type
SNGG
Type
TNGG
Type
VNGG
Type
Features
a For finish cutting.

a Lead breaker controls
chip flow.
FS
a Parallel breaker for light
Breaker
K
cutting.
a Excellent chip control for
low to medium feed rates.
a Parallel breaker for medium
Feed (mm/rev)
R/L
cutting.
a Good chip control for
medium feed rates.
A027
TURNING INSERTS
TURNING INSERTS
WIPER INSERT
a Improving Surface Finish

Under the same machining conditions as conventional breakers, but with the feed rate
increased, the surface finish of the workpiece can be improved.
a Improving Efficiency
y What is a Wiper Insert?
High feed rates not only shortened machining times but also make it possible to
combine roughing and finishing operations.
The wiper insert is designed with a wiper edge that is

situated where the straight edge meets the corner
radius.
Wiper
In comparison to conventional
breakers, the surface finish does
not deteriorate even if the feed
rate is doubled.
Machining at high feed rates
improves cutting efficiency.
Finished surface
Same surface
roughness
Wiper insert
High feed (The feed rate is doubled.)
When a change to high feed conditions, the time required to cut one component is decreased,
thus more parts can be machined with each insert. In addition, the high feed rate prevents
rubbing, therefore, delaying the progression of wear and increasing the tool life of the insert.
a Improving Chip Control

Under high feed conditions, the chips generated become thicker and are more easily
broken, thus, chip control is improved.
y A wiper insert + machining at high feed rate
Standard insert
Reduced machining time (per workpieces)

Increased number of workpieces (per definitive time period)
Improving chip control
The conventional feed condition
y A wiper insert + machining at conventional feed rate
Please use a wiper insert at high feed rate.

40
Surface Roughness
Rz (m)
a Increased Tool Life
Standard Insert
30
Wiper Insert
MW Breaker
20
Eliminating the finishing step by roughing and finishing together
<Cutting Conditions>
Workpiece : JIS S45C
Insert : CNMG120408-oo
Cutting Speed=200m/min
Depth of Cut=1.5mm
Feed Speed=0.2 0.6mm/rev
Wet Outer Diameter Cutting
(Separate roughing and finishing steps | Single-step machining)
Reducing cycle times

Increased productivity
Avoiding Line-Stoppage
10
0
0.2
0.4
0.6
Feed f (mm/rev)
0.8
<The realization of Reduced Costs!!>
<Ex>The surface roughness does not deteriorate

even if the feed rate is doubled (0.30.6)!
The estimate of finished surface roughness when using a wiper insert
Rz(W)=Rz0.5
The effects of wiper inserts on external

machining, boring and facing.
In case the
angle is over
than 5
Rz(W) = Finished surface roughness

when using a wiper insert.
Rz : Finished surface roughness from
conventional conditions.
(When using a standard insert)
surface roughness when machining at

*The
corner R or taper angle over 5, is the same
Effective uses of a wiper insert

Non effective uses of a wiper insert
as machining with standard inserts.
Special attention is not necessary when using CNMG WNMG CCMT types
y No Restriction for Holders
y Not Necessary to Adjust
End Cutting
Angle
A standard holders can be used.

( A double clamp, high rigidity tool is
recommended.)
the Machining Programme
75
Conventional machining
programmes can be used.
End Cutting
Angle
Non
restriction
95
The CNMG type can

be used as a wiper at
the 100corner.
(The CNMG WNMG CCMT

types are based
Not
on the
necessary to
ISO/ANSI.)
adjust
Special attention is necessary when using the DNMX TNMX types due to the special top face geometry
y Necessary to Adjust
y Restriction for Holders
The hole geometry of the DNMX and TNMX type are

the same as the DNMG and TNMG types. The "X"
represents the special geometry of the Corner point.
93
(Specified)
A028
End Cutting Angle
Theoretical Surface
Roughness Rz (m)
Use a holder with end cutting angle 93 for improving wiper efficiency. A holder with end
cutting angle 91 can improve wiper efficiency (see the following figure), however, there is no
Ex):Theoretical surface roughness of holders
wiper efficiency with other end cutting
in using the TNMX160412-MW.
40
angles (60, 90, 107etc.).
MW (93)
MW (91)
30
Standard
corner radius
20
10
0
0.1
0.2
0.3
0.4
0.5
Feed f (mm/rev)
0.6
the Machining Programme
When machining errors occur, please

adjust the programme.
(The DNMXTNMX types are not
based on the ISO/ANSI. Please
refer to the next page.)
Adjustment
necessary
Standard corner
radius
Wiper corner
radius
<Example of insert point>
TURNING INSERTS
Adjustment of machining programmes for DNMX TNMX types

Basic Process) Adjusting Toward X-axis and Z-axis
Adjustment toward Z-axis
Adjusting the differential between a standard insert and Z-axis / X-axis.
Standard insert
Adjustment toward X-axis

DNMX,TNMX
type
Standard insert
(Not closed to Corner R)
0.01mm
DNMX,TNMX
type
Corner radius 0.4,0.8 : 0.04 mm

Corner radius 1.2
: 0.05 mm
A) Adjusting a Taper
*Necessary to maintain a correct taper.
Adjust the relief angle toward the normal line.
Geometry of
adjusted program
Note) Adjust the angle toward the normal line in the case where the
adjustment number is minus ( ' =60 70) and is not machined completely.
'( )
Classification
Corner radius
of
th t
p
u
de c
e er
Th ov
o
th
ep t
e d er cu
h
T ov
'( +)
The actual machining

geometry
Taper Angle '

-25 -15
-10
-5
10
15
2035
40
45
50
55
6065
70
7585
90
1.2
0.04
0.03
0.01
0.02
0.03
0.04
0.05
0.04
0.04
0.02
0.01
-0.01
0.01
0.8
0.03
0.02
0.01
0.01
0.02
0.03
0.04
0.03
0.03
0.02
-0.01
0.01
0.4
0.02
0.01
0.01
0.01
0.01
0.02
0.02
0.02
0.01
0.01
-0.01
-0.01
The number+numbers:adjustment of relief angle, -numbers:adjustment of drive-in angle (mm)
B) Adjusting a Corner R
*Necessary to maintain a correct corner radius.
Adjust the work diameter same as the taper to prevent cut-over.
The value of adjustment to work R

= Work R + the adjustment value
Geometry of adjusted
programme
No adjusting the corner radius in this case.

The adjustment amount on the
workpiece radius.
Corner Radius 0.4 | Work Radius+0.05(mm)

1.
Workpiece
radius 2.0
1.
The corner radius

of the insert
0.0
Ex) : In case of machining R 2.0 when using a corner R 1.2 type insert.
R2.14
= 2.0 + 0.14
Workpiece
radius 2.0
Work radius Adjusted conditions
The actual machining

geometry
The Easy-to-correct Method
In correcting corner radius:

It is not necessary to adjust the machining programme, however, machining errors can occur within max.
0.03mm due to correcting by an approximate number.
Corner Radius Correction Input the correction number of each corner radius.
The value of corrected corner radius
= approximation
Ex):In the case of machining a corner with a radius R 2.0 when using
an insert with a corner radius R 1.2.
*No adjusting the machining the programme in this case.
1.
1.
2
Corner Radius 0.4 | R0.36(mm)
16
The value of corrected

corner radius = approximation
The corner radius

of a insert

R2.0
R2.0
Others) The value of correction is same for both DNMX and TNMX. Discriminate them by the size of corner radius.
A029
Hardened Steel
A030
H10
H20
H30
MB8025
MB810
MBC010
MB730
N01
MD205
UTi20T
MB710
UTi20T
CBN
N20
N30
S30
=
MD230
MB4020
MBS140
HTi05T
HTi10
VP45N
MP3025
VP25N
AP25N
VP25N
AP25N
VP25N
MB730
UTi20T
NX2525
NX3035
UP20M
UP20M
NX2525
VP20RT
VP20RT
MP7035
VP20MF
VP20MF
M01
AP25N
NX2525
VP10RT
UE6020
MC6025
VP15TF
UH6400
UE6035
UE6110
MY5015
Coated
CBN
MD220
HTi10
N10
RT9010
MT9015
RT9005
MP9015
VP20RT
VP15TF
VP10RT
MC7025
US735
UE6105
MC6015
Cemented
Carbide
MB835
H01
Coated
Cermet
MBC020
S20
VP15TF
K30
Cermet
BC8110
S10
VP10RT
K20
UC5115
M40
PVD
TF15
S01
Coated Carbide
MB825
H
P40
VP20RT
S
M30
MY5015
P30
VP15TF
K10
CVD
VP10RT
N
K01
MC5015
M20
US7020
P20
VP05RT
K
MC7015
M10
UC5105
Steel
P10
MC5005
Stainless Steel
M
P01
MP9005
Cast Iron
US905
Non-Ferrous Metal
ISO
BC8020
TURNING INSERTS
TURNING INSERTS
GRADES FOR TURNING
a INDEXABLE INSERT GRADES FOR TURNING

PCD
(Sintered Diamond)
STEEL
TURNING INSERTS
TURNING APPLICATION RANGE

STAINLESS STEEL
Cermet and Coated Cermet

300
400
300
200
NX2525
NX3035
MP3025
MC7015
MC6025
Cemented Carbide
UE6035
VP45N
VP15TF
US735
100
Cutting Speed (m/min)
CVD PVD Coated Carbide
UE6105
AP25N
VP25N
MC6015
200
MC7025
VP15TF
US735
100
MP7035
Cemented Carbide
UH6400
UTi20T
UTi20T
0
0.2
0.4
0.6
0.8
0.1
0.2
0.4
0.5
0.6
Feed (mm/rev)
Feed (mm/rev)
0.3
CAST IRON
NON-FERROUS METAL
500
Sintered CBN
MBS140
400
Solid CBN
800
MB710
MB730
MB4020 MC5005
MD205
MD220
Sintered Diamond
300
200
AP25N
VP25N
NX2525
Cermet and Coated Cermet

MC5015
VP10RT
VP15TF
100
HTi05T
MD230
600
Cemented Carbide
400
200
HTi10
Cemented Carbide
HTi10
0.2
0.4
0.6
Feed (mm/rev)
0.8
0.1
0.2
0.3
0.4
Feed (mm/rev)
A031
TURNING INSERTS
TURNING INSERTS
TURNING APPLICATION RANGE

a Recommendation of the insert grade based on cutting speed and conditions for each workpiece.
P STEEL (Finish Cutting)
P STEEL (Medium to Rough Cutting)

400
400
300
200
MC6015
100
MC6025
UE6035
UE6105
300
AP25N
NX3035
NX2525
100
VP15TF
Cutting Conditions
Cutting Conditions
K CAST IRON
M STAINLESS STEEL
500
200
MC7015
MC7025
MP7035
100
300
MP3025
200
400
MC5005
300
MC5015
200
VP15TF
100
K CAST IRON (CBN)
1500
MB4020
MB730
1000
MB710
Cutting Conditions
A032
VP15TF
Cutting Conditions
500
NX2525
Cutting Conditions
Stable Cutting
Continuous Cutting
Pre-Machined
General Cutting
Unstable Cutting
N NON-FERROUS METAL (PCD)
N NON-FERROUS METAL
1500
600
400
HTi10
200
1000
MD220
500
Cutting Conditions
Cutting Conditions
S HEAT RESISTANT ALLOY
S TITANIUM ALLOY
100
75
MP9005
MP9015
50
VP15TF
100

TURNING INSERTS
75
50
MT9015
VP15TF
25
25
Cutting Conditions
Cutting Conditions
H HARDENED MATERIALS (CBN)

400
MBC010
300
200
BC8110
BC8020
100
MB835
0
MBC020
Cutting Conditions
A033
TURNING INSERTS
TURNING INSERTS
COATED CARBIDE (CVD)

a Special tough fibrous structure improves wear and fracture resistance.
a It covers a wide application range and thus reduces the number of tools required.
SELECTION STANDARD
a TURNING
250
(150 400)
MC6025
200
(100 280)
P30
UE6035
150
(80 200)
P40
MC7015
200
(160 250)
P20
US735
100
(80 120)
Continuous
Cutting
UC5105
300
(200 400)
Interrupted
Cutting
UC5115
M30
Continuous
Heat Resistant
and
Interrupted
Alloy
Cutting
US905
250
(150 300)
80
(50 100)
K10
K20
UC5115
Cast Iron
Ductile Cast Iron
K01
MC5015
M40
US735
Continuous
and
Interrupted
Cutting
M20
MY5015
150
(120 200)
MC7025
M10
MC7025
Stainless Steel
M01
UC5105
Continuous
Cutting
MC7015
MC5005
Interrupted
Cutting
US7020
Steel
P10
UH6400
MC6015
Continuous
Cutting
UE6035
P01
UE6020
300
(200 400)
MC6025
UE6105
Application Range
MY5015
ISO
UE6110
Recommended Cutting
Speed (m/min)
MC6015
Recommended Grade
UE6105
Cutting
Mode
K30
S01
US905
Work Material
High reliability for a wide range of steel machining.
MC6015
Smooth coating surface
y Nano-Texture Technology
Prevents abnormal damage,

welding and chipping
The optimised crystal growth,

Nano-Texture coating
technology gives outstanding
wear and chipping resistance.
Ultra thick layer

Nano-texture Al2O3
y TOUGH-Grip Technology
The interface between the
layers is controlled at the nano
level, allowing the TOUGH
GRIP layer extremely high
levels of adhesion to prevent
delamination.
Delivers outstanding wear

resistance even at high
temperature
TOUGH-Grip
Prevents delamination of a
coating
Nano-texture TiCN
Provides superior wear resistance
and chipping resistance
Special carbide substrate

Prevents crack development
Stable tool life
A034
TURNING INSERTS
GRADE CHARACTERISTICS
Substrate
Grade
Coating Layer
Hardness (HRA)
T.R.S (GPa)
Surface
Composition
Thickness
UC5105
92.2
2.0
TiCN-AI2O3
Thick
MC5005
91.0
2.2
TiCN-AI2O3
Thick
UC5115
91.0
2.2
TiCN-AI2O3
Thick
MC5015
91.0
2.2
TiCN-AI2O3
Thick
UE6105
90.8
1.8
Tough
Accumulated TiCN-AI2O3-Ti Compound
Thick
UE6110
90.3
2.0
Tough
Thick
UE6020
90.0
2.2
Tough
Thick
MC6015
90.2
2.2
Tough
Thick
MC6025
90.2
2.2
Tough
Thick
UE6035
89.5
2.3
Tough
TiCN-AI2O3-TiN
Thick
UH6400
89.5
2.3
Tough
Thick
MC7015
90.7
2.0
Tough
TiCN-AI2O3-TiN
Thin
US7020
90.5
2.0
Tough
TiCN-AI2O3-TiN
Thin
MC7025
89.4
2.4
TiCN-AI2O3-TiN
Thin
US735
89.0
2.6
Ti Compound
Thin
US905
92.2
2.0
TiCN-AI2O3-TiN
Thin
MY5015
91.2
2.4
TiCN-AI2O3-TiN
Thin
* 1GPa=102kg/mm
ISO Insert Series for Cast Iron Turning
MC5005/MC5015
The CVD nano-coated layer
with high strength is formed
by the synergistic effects
between Nano-texture coating
technology and TOUGH-GRIP
Technology,thereby achieving
superior wear resistance in the
turning for cast iron.
Ultra thick layer

Nano-texture
Al2O3
TOUGH-Grip
Nano-texture
Al2O3
TOUGH-Grip
Nano-texture
TiCN
Nano-texture
TiCN
MC5005
MC5015
A035
TURNING INSERTS
TURNING INSERTS
COATED CARBIDE (PVD)

a PVD coating prolongs tool life under the same cutting conditions compared to uncoated carbide.
a Coating of tools with sharp edges is possible without softening or changing the edge quality of the
substrate.
SELECTION STANDARD
a TURNING
Cast Iron
VP10RT
120
(100 150)
VP15TF
120
(100 150)
VP20RT
120
(100 150)
MP9005
60
(30 100)
50
(25 80)
40
(20 50)
40
(20 50)
MP9015
Heat Resistant Alloy
VP15TF
VP20RT
UP20M
VP20RT
VP20MF
VP15TF
UP20M
M40
MP7035
UP20M
M30
K01
K10
K20
K30
S01
S10
S20
S30
VP20RT
VP20RT
M20
VP20RT
VP20MF
VP15TF
Stainless Steel
M10
VP20MF
VP15TF
M01
VP20RT
VP10RT
P40
VP10RT
P30
MP9015
UP20M
P20
VP15TF
VP20RT
P10
VP15TF
VP20MF
P01
VP05RT
Steel
Application Range
VP10RT
VP15TF
120
(100 150)
120
(100 150)
120
(100 150)
120
(100 150)
120
(100 150)
120
(100 150)
120
(100 150)
120
(100 150)
120
(100 150)
120
(100 150)
ISO
VP10RT
VP10RT
Recommended CuttingSpeed
(m/min)
VP10RT
Recommended Grade
MP9005
Work Material
ISO Turning Inserts for Difficult to Cut Materials
MP9005/MP9015
New technology
High Al-(Al,Ti)N single layer coating
Special carbide substrate
ISO Grade
A036
Grade
Concept
S01
MP9005
Top-quality grade focusing on wear resistance
S10
MP9015
First recommendation for general applications
Application
Finish-Medium Cutting
Medium-Rough Cutting
a The optimized alloy structure and special alloy binder improves both wear and fracture resistance.
a It covers a wide application range and reduces the number of tools required.
a NX3035 for wet cutting.
a NX2525 for dry cutting.
TURNING INSERTS
CERMET
SELECTION STANDARD
a TURNING
Work Material
Cutting
Mode
Recommended Grade
Recommended Cutting
Speed (m/min)
Continuous
Cutting
NX2525
220
(180 250)
ISO
Application Range
P10
Interrupted
Cutting
200
(190 260)
NX3035
P20
NX3035
Steel
NX2525
P01
Cast Iron
Ductile Cast Iron
180
(150 210)
NX2525
Finishing
K10
NX2525
K01
K20
Hardness (HRA)
T.R.S (GPa)
NX2525
92.2
2.0
NX3035
91.5
2.1
Grade
Thermal Conductivity Thermal Expansion

(W/m K)
(10-6/K)
33
7.8
35
* 1GPa=102kg/mm , 1W/m K=2.3910

2
7.8
-3
cal/cm sec r
A037
TURNING INSERTS
TURNING INSERTS
COATED CERMET
a Coated cermet (PVD coating) has superior wear and fracture resistance, and therefore provides a
stable cutting performance.
SELECTION STANDARD
a TURNING
Continuous
Cutting
VP25N
AP25N
240
(190 290)
Interrupted
Cutting
MP3025
230
(180 280)
ISO
Application Range
P01
P10
Steel
P20
P30
AP25N
Recommended
CuttingSpeed (m/min)
VP45N
Recommended Grade
MP3025
Cutting
Mode
VP25N
Work Material
Finishing
VP25N
AP25N
160
(110 230)
K10
AP25N
Cast Iron
Ductile Cast Iron
VP25N
K01
K20
Effective for production of small parts.
MP3025
MP3025 provides
improved adhesion for
coating layer due to
the newly-developed
special substrate.
Uniform flank wear
allows prolonged
machining that
maintains excellent
surface finish.
A038
Ti-compound PVD coating

provides excellent wear and
welding resistance.
Substrate surface provides
excellent adhesion strength for
coating layer.
Substrate with superior fracture
resistance and thermal shock
resistance.
TURNING INSERTS
CEMENTED CARBIDE
a UTi grades are available for steel and cast iron. HTi grades are available for non-ferrous and
non-metal materials and are also suitable for cast iron.
SELECTION STANDARD
a TURNING
Work Material
Recommended Grade
Recommended Cutting
Speed (m/min)
UTi20T
100
(60 130)
ISO
Application Range
P10
P20
UTi20T
Steel
P30
M10
100
(60 130)
M20
UTi20T
UTi20T
Stainless Steel
120
(80 150)
HTi10
100
(50 150)
UTi20T
100
(50 150)
Cast Iron
K01
K10
K20
K30
N
HTi10
600
(400 800)
RT9005
70
(50 100)
MT9015
RT9015
60
(40 80)
TF15
50
(40 70)
HTi10
N01
Non-Ferrous Metal
UTi20T
HTi05T
HTi10
HTi05T
M30
N10
N20
TF15
S20
RT9010
S10
MT9015
Heat-resistant Alloy
Ti Alloy
S01
RT9005
N30
S30
MAIN COMPONENT AND APPLICATION

ISO
P
K
Main Component
M
WC-TiC-TaC-Co
N
S
Characteristics
Work Material
Heat / deformation resistance.
Carbon steel, alloy steel, stainless steel and cast iron
WC-Co
High rigidity and wear resistance.
Cast iron, non-ferrous metals, and non-metal
WC-Co
High heat resistance and wear resistance. Heat-resistant alloy, Ti alloy
P
K
S
Thermal Conductivity Thermal Expansion Young's Modulus

(W/mK)
(x10-6/K)
(GPa)
Grade
Hardness (HRA)
UTi20T
90.5
38
HTi05T
HTi10
92.5
92.0
RT9005
MT9015/RT9010
TF15
92.2
92.0
91.5
ISO
T.R.S(GPa)
5.5
*
520
79
79
4.5
4.6
600
630
1.5
2.0
79
79
71
4.5
4.6
5.3
600
630
580
2.0
2.2
2.5
* 1GPa=102kg/mm , 1W/m K=2.3910

2
2.0
-3
cal/cm sec r
A039
TURNING INSERTS
TURNING INSERTS
MICRO-GRAIN CEMENTED CARBIDE

(SOLID TOOLS)
a Compared to normal cemented carbide, micro-grain types have higher wear resistance and toughness.
SELECTION STANDARD
Cutting Tool
Recommended Grade
Work Material
PCB Miniature Drill
SF10
MF10
MF20
Non-Metal
Solid Carbide Drill

Turning Inserts
Milling Inserts
TF15
Steel Cast Iron
Solid End Mill
HTi10
TF15
MF10
Steel Cast Iron
Gear Hob
Reamer
Tap etc.
TF15
MF20
MF30
Steel Cast Iron, etc.
Grade Characteristics
Grade
ISO
Wear
Resistance
Fracture
Resistance
Corrosion
Resistance
HTi10
14.9
92.0
3.2
K10
TF15
14.5
91.0
4.0
K20
SF10
14.9
92.7
3.8
K01
MF10
14.6
93.0
4.0
K01
MF20
14.2
92.0
4.4
K10
13.7
90.7
4.3
K20
MF30
* 1GPa=102kg/mm
** After HIP
A040
**
Specific Gravity Hardness (HRA) T.R.S (GPa)
Memo
A041
CLASSIFICATION
Breaker Name
and
Picture
FH
Cross Section
Geometry
Features
First recommendation for finishing carbon steel,

alloy steel and stainless steel
Double sided chipbreaker.
Stable chip control even at small depth of cut.
Mild Steel

Sharp edge gives best performance.

Effectively controls adhesive chips.
Suitable for mild steel finishing.
ap (mm)
Alternative chipbreaker for finishing carbon steel

and alloy steel
R/L-FS
ap (mm)
0.1 0.2 0.3 0.4

f (mm/rev)
Nose

15
3
2
Flank
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
15
Flank
3
2
14
ap (mm)
0.1 0.2 0.3 0.4

f (mm/rev)

Lead chipbreaker controls chip flow.
The sharp edge produces a good surface finish.
Flank
3
2
14
1
0.1 0.2 0.3 0.4
f (mm/rev)
Nose

ap (mm)
15
0.1
Flank
1
0
0.1
0.3
f (mm/rev)
0.5
Stainless Steel
4
ap (mm)
Light Cutting
Flank
First recommendation for light cutting of stainless

steel
Nose
Finishing
0.2
14

A narrow lead chipbreaker for good chip control.
First recommendation for light cutting of carbon steel

and alloy steel
15
M class double sided chip breaker.

Stable chip control at light cutting range.
Breaker with high rake angle provides excellent burr control.
A042
0.1 0.2 0.3 0.4

f (mm/rev)
Precise finishing

Stable chip control at light cutting range.
The curved edge allows smooth chip discharge.
LM
Flank
LP
Nose
R/L-F
15
ap (mm)

G class insert tolerance is suitable for workpieces requiring close
dimensional tolerances.
0.1 0.2 0.3 0.4

f (mm/rev)
ap (mm)
Finish Cutting
PK
Flank
Mild Steel

Ideal for heat-resistant alloy and titanium alloy.
The sharp edge produces good cutting surface.
Nose
First recommendation for finishing mild steel
First recommendation for finishing difficult-to-cut

materials
12
16
FJ
0.1 0.2 0.3 0.4

f (mm/rev)
Alternative chipbreaker for finishing mild steel
FY
Flank
ap (mm)
12
FS
Nose

ap (mm)
Tolerance

Application
TURNING INSERTS
TURNING INSERTS
11
0.2
Nose
15
0.50
3
2
1
0
0.1
0.3
0.5
f (mm/rev)
20
Flank
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
CNMG_FH
DNMG_FH
SNMG_FH
TNMG_FH
VNMG_FH
WNMG_FH
^ A092
^ A098
^ A105
^ A110
^ A116
^ A119
CNMG_FS
DNMG_FS
SNMG_FS
TNMG_FS
VNMG_FS
WNMG_FS
^ A092
^ A098
^ A105
^ A110
^ A116
^ A119
CNMG_FY
DNMG_FY
TNMG_FY
WNMG_FY
^ A092
^ A098
^ A110
^ A119
CNGG_FJ
DNGG_FJ
VNGG_FJ
^ A092
^ A098
^ A116
CNGG_PK
DNGG_PK
TNGG_PK
^ A092
^ A098
^ A110
Round
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
FH
FS
FY
FJ
PK
TNGG_R/L-FS
R/L-FS
^ A110
TNGG_R/L-F
VNGG_R/L-F
^ A110
^ A116
R/L-F
CNMG_LP
DNMG_LP
SNMG_LP
TNMG_LP
VNMG_LP
WNMG_LP
^ A092
^ A098
^ A105
^ A110
^ A116
^ A119
CNMG_LM
DNMG_LM
SNMG_LM
TNMG_LM
VNMG_LM
WNMG_LM
^ A092
^ A099
^ A105
^ A111
^ A116
^ A119
LP
LM
A043
CLASSIFICATION
Breaker Name
and
Picture
LK
Cross Section
Geometry
Features
First recommendation for light cutting of cast iron
Cast Iron
Narrow positive land provides low cutting resistance and excellent

finish.
ap (mm)
Tolerance

Application
TURNING INSERTS
TURNING INSERTS
3
1
Enhanced chip disposal for depth of cut smaller than the corner R.
SA
Alternative chipbreaker for light cutting of carbon steel

and alloy steel
Superior chip control at small depth of cuts.
Covers copying and back turning with wavy edge.
Recommended for workpieces in the 200 300HB range.
Light Cutting
SW
Flank
1
0
0.1
0.3
f (mm/rev)
15
Nose
10
Flank
1
0
0.1
0.3
f (mm/rev)
0.5
Nose
0.15
7
Flank
1
0.3
0.5
f (mm/rev)

Effectively controls adhesive chips.
Suitable for mild steel light cutting.
ap (mm)
0.1
0.15
18
7
Nose
10
3
2
Flank
1
0.1
0.3
0.5
f (mm/rev)
10
0.2
Nose

ap (mm)
0.34
25
18
Mild Steel
12
3
2
Flank
1
0
0.1
0.3
0.5
f (mm/rev)
12
Flank
ap (mm)
0.3
25
First recommendation for light cutting of mild steel

and alloy steel
0.2
15
0.2
1
0
0.1
0.3
f (mm/rev)
0.5
Light cutting

Parallel chipbreaker.
Excellent chip control at low to medium feed rates.
Flank
4
3
14
2
1
0
0.1
0.3
f (mm/rev)
A044
0.5

The wiper allows up to two times higher feed.
Wiper design for increased productivity and improved surface finish.

and alloy steel
Nose
15
ap (mm)
0.5

Parallel chipbreaker controls chip flow.
Suitable for finish-light cutting.
Precision chipbreaker.
R/L-K
0.3
f (mm/rev)
Wiper insert for light cutting of carbon steel and alloy steel

Suitable for light cutting.
R/L-1G
0.1
0.15
20
SY
Flank
ap (mm)
0.5
ap (mm)

Can be used at low depth of cuts and high feed rates.
Recommended for workpieces in the 160 250HB range.
0.3
f (mm/rev)
ap (mm)

and alloy steel
6
0.1
SH
0.15
ap (mm)
First recommendation for light cutting of

difficult-to-cut materials
15
2
0
LS
Flank
0.5
0.25
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
CNMG_LK
DNMG_LK
SNMG_LK
TNMG_LK
VNMG_LK
WNMG_LK
^ A093
^ A099
^ A105
^ A111
^ A116
^ A119
CNMG_LS
DNMG_LS
TNMG_LS
VNMG_LS
WNMG_LS
^ A093
^ A099
^ A111
^ A117
^ A119
CNMG_SH
DNMG_SH
SNMG_SH
TNMG_SH
VNMG_SH
WNMG_SH
^ A093
^ A099
^ A105
^ A111
^ A117
^ A120
CNMG_SA
DNMG_SA
SNMG_SA
TNMG_SA
WNMG_SA
^ A093
^ A099
^ A105
^ A111
^ A120
CNMG_SW
DNMX_SW
TNMX_SW
WNMG_SW
^ A093
^ A099
^ A111
^ A120
CNMG_SY
DNMG_SY
SNMG_SY
TNMG_SY
WNMG_SY
^ A093
^ A099
^ A106
^ A111
^ A120
CNMG_C
DNMG_C
SNMG_C
TNMG_C
WNMG_C
^ A093
^ A100
^ A106
^ A111
^ A120
SNMG_R/L-1G TNMG_R/L-1G
^ A106
Round
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
LK
LS
SH
SA
SW
SY
R/L-1G
^ A111
TNGG_R/L-K
R/L-K
^ A112
A045
CLASSIFICATION
MJ

Double sided chipbreaker, Single sided chipbreaker (D type, V type).
MP
First recommendation for medium cutting of carbon steel

and alloy steel
Suitable for medium to light cutting.
Breaker geometry appropriate for copying and back turning.
Cutting edge geometry for an optimum balance of sharpness and
fracture resistance.
MK
First recommendation for medium cutting of stainless steel

Optimized land geometry by simulation analysis technology controls
the plastic deformation of the corner and achieves the long tool life.
Nose
13
3
2
Flank
1
0
0.1
0.3
0.5
f (mm/rev)
Nose
13
4
3
2
Flank
1
0
0.1
0.3
0.5
f (mm/rev)
Nose

5
4
3
2
1
0 0.1
0.3 0.5
f (mm/rev)
0.15
15
Flank
0.2
11
Nose
Stainless Steel
5
4
3
2
1
0
0.3
Flank
0.1
0.3 0.5
f (mm/rev)
First recommendation for medium cutting of cast iron
Cast Iron
Optimum balance between sharpness and high edge strength

for general use.
ap (mm)
MM
ap (mm)

M
Light Cutting

ap (mm)
MJ
Cross Section
Geometry
Features
ap (mm)
Breaker Name
and
Picture
ap (mm)
Tolerance

Application
TURNING INSERTS
TURNING INSERTS
5
4
3
2
1
0 0.1
0.3
10
Flank
15
0.25
3
Alternative chip breaker for medium cutting for cast iron
Cast Iron
Breakers are suitable for a wide range of applications.

Maintenance of high stability by the flat-land.
ap (mm)
GK
15
0.25
3
1
0 0.1 0.3 0.5 0.7
f (mm/rev)
Alternative chip breaker for light to medium cutting of

stainless steel
Alternative chip breaker of main chip breaker LM and MM.
Excellent notch wear resistance for light to medium cutting.
MA
First recommendation for medium cutting of carbon steel

and alloy steel
Alternative chipbreaker for finishing and light cutting of
cast iron
Stainless Steel
ap (mm)
GM
First recommendation for rough cutting of mild steel

Alternative chipbreaker for medium cutting of
carbon steel and alloy steel
Flat land offers high edge strength.
Nose
25
0.5
15
Flank
0.1
0.3 0.5
f (mm/rev)
5
4
3
2
1
0 0.1
0.3 0.5
f (mm/rev)
0.5
25
15
Nose
5
4
3
2
1
0 0.1
0.3 0.5
f (mm/rev)
0.2
22
6
Flank
0.2
22
6
Nose

ap (mm)
MH
5
4
3
2
1
0

Positive land provides sharp cutting action.
A046
Flank
ap (mm)
Medium Cutting
0.3 0.5
f (mm/rev)
16
0.25
Flank
16
0.35
Rhombic 55
CNMG_MJ
Square 90
Triangular 60
Rhombic 35
Trigon 80
DNMG_MJ
TNMG_MJ
VNMG_MJ
WNMG_MJ
^ A093
^ A100
^ A112
^ A117
^ A120
CNGG_MJ
DNGM_MJ
VNGM_MJ
^ A093
^ A100
^ A117
CNMG_MP
DNMG_MP
SNMG_MP
TNMG_MP
VNMG_MP
WNMG_MP
^ A094
^ A100
^ A106
^ A112
^ A117
^ A121
CNMG_MM
DNMG_MM
SNMG_MM
TNMG_MM
VNMG_MM
WNMG_MM
^ A094
^ A100
^ A106
^ A112
^ A117
^ A121
CNMG_MK
DNMG_MK
SNMG_MK
TNMG_MK
VNMG_MK
WNMG_MK
^ A094
^ A100
^ A106
^ A112
^ A117
^ A121
CNMG_GK
DNMG_GK
SNMG_GK
TNMG_GK
VNMG_GK
WNMG_GK
^ A094
^ A101
^ A107
^ A112
^ A117
^ A121
CNMG_GM
DNMG_GM
SNMG_GM
TNMG_GM
VNMG_GM
WNMG_GM
^ A094
^ A101
^ A107
^ A112
^ A117
^ A121
CNMG_MA
DNMG_MA
SNMG_MA
TNMG_MA
VNMG_MA
WNMG_MA
^ A095
^ A101
^ A107
^ A113
^ A118
^ A121
CNMG_MH
DNMG_MH
SNMG_MH
TNMG_MH
VNMG_MH
WNMG_MH
^ A095
^ A101
^ A107
^ A113
^ A118
^ A121
Round
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
MJ(M)
MJ(G)
MP
MM
MK
GK
GM
MA
MH
A047
CLASSIFICATION
Breaker Name
and
Picture
Standard
Cross Section
Geometry
Features

Alternative chipbreaker for medium cutting of carbon steel
and alloy steel
Flat land offers high edge strength.
Nose

ap (mm)
Tolerance

Application
TURNING INSERTS
TURNING INSERTS
5
4
3
2
1
0 0.1
15
0.25
15
0.25
19
0.25
Flank
0.3
0.5
f (mm/rev)

A wide chip pocket prevents chip jamming.
First recommendation for medium cutting of stainless steel,

mild steel and difficult-to-cut materials
The sharp edge gives best performance.
5
4
3
2
1
0 0.1
Flank
0.3 0.5
f (mm/rev)
Stainless Steel
5
4
3
2
1
0 0.1
R/L-ES
Alternative chipbreaker for medium cutting of

stainless steel
Good balance of edge strength and sharpness.
Right- or left-hand breaker for unidirectional chip control.
0.3
19
Nose
25
0.5
15
Flank
0.3 0.5
f (mm/rev)
0.5
25
15
Stainless Steel
ap (mm)
Medium Cutting
MS
Nose

ap (mm)
Wiper insert for medium cutting carbon steel and

alloy steel
ap (mm)
MW
5
4
3
2
1
0 0.1
Flank
0.16
15
0.3
0.5
f (mm/rev)
Alternative chipbreaker for medium cutting of carbon steel

and alloy steel
Parallel chipbreaker controls chip flow.
Suitable for light to medium cutting.

ap (mm)
R/L-2G
5
4
3
2
1
0 0.1
Flank
0.2
14
0.3
0.5
R/L
G
Medium cutting

Parallel chipbreaker.
Good chip control for medium feed rates.
ap (mm)
f (mm/rev)
5
4
3
2
1
0 0.1
Flank
0.25
14
0.3
0.5
f (mm/rev)
Rough Cutting
RM
First recommendation for rough cutting of stainless

steel
Excellent fracture resistance at interrupted cutting due to the
optimum land angle and honing geometry.
RK
For rough cutting of carbon steel, alloy steel and

stainless steel
Seating surface and wide land 3 or more times that of conventional
products and provide high cutting stability for interrupted machining
and scale removal.
A048
ap (mm)
Double sided chip breaker.

For interrupted cuts and removing scale.
Good balance of cutting edge strength and low cutting resistance
because of suitable rake angle.
Nose

5
0.33
3
Flank
0.33
1
0 0.1 0.3 0.5 0.7
f (mm/rev)
Nose
Stainless Steel
7
ap (mm)
First recommendation for rough cutting of carbon steel

and alloy steel
0.32
3
1
0 0.1 0.3 0.5 0.7
f (mm/rev)
Flank
0.32
6
Cast Iron
Flank
ap (mm)
RP
5
3
1
0 0.1 0.3 0.5 0.7
f (mm/rev)
15
0.35
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
CNMG
DNMG
SNMG
TNMG
VNMG
WNMG
RNMG
^ A095
^ A101
^ A107
^ A113
^ A118
^ A122
^ A104
CNMG_MW
DNMX_MW
TNMX_MW
WNMG_MW
^ A095
^ A101
^ A113
^ A122
CNMG_MS
DNMG_MS
SNMG_MS
TNMG_MS
VNMG_MS
WNMG_MS
^ A095
^ A102
^ A107
^ A113
^ A118
^ A122
TNMG_R/L-ES
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
Standard
MW
MS
R/L-ES
^ A113
TNMG_R/L-2G
R/L-2G
^ A114
DNGG_R/L
SNGG_R/L
TNGG_R/L
VNGG_R/L
^ A102
^ A108
^ A114
^ A118
CNMG_RP
DNMG_RP
SNMG_RP
TNMG_RP
WNMG_RP
^ A096
^ A102
^ A108
^ A114
^ A122
CNMG_RM
DNMG_RM
SNMG_RM
TNMG_RM
WNMG_RM
^ A096
^ A102
^ A108
^ A114
^ A122
CNMG_RK
DNMG_RK
SNMG_RK
TNMG_RK
WNMG_RK
^ A096
^ A102
^ A108
^ A115
^ A122
R/L
RP
RM
RK
A049
CLASSIFICATION
Breaker Name
and
Picture
RS
Cross Section
Geometry
Features
First recommendation for rough cutting of difficultto-cut materials

Positive land increases welding resistance and suppresses chip
welding and abrasion at low speed cutting.
Flank
ap (mm)
Tolerance

Application
TURNING INSERTS
TURNING INSERTS
25
First recommendation for rough cutting of difficultto-cut materials

Excellent balance of edge sharpness and strength.
Edge geometry with high face wear resistance.
HZ
First recommendation for heavy cutting of mild steel

and stainless steel
Heavy Cutting
Single sided chipbreaker.

Covers the lower end of the heavy cutting region.
Low cutting resistance due to positive land and curved edge.
Teardrop dots improve chip control without increasing cutting resistance.
HX
First recommendation for heavy cutting of carbon steel

and alloy steel
Covers the medium range of the heavy cutting region.
Owing to the straight edge and chamfer,
it gives a balance of sharpness and strength.
Variable land and a wavy chipbreaker for good chip control.
HV
Alternative chipbreaker for heavy cutting of carbon steel

and alloy steel
Flat Top
M
ap (mm)
Flank
Nose
7
0.15
18
5
3
Flank
1
0 0.1 0.3 0.5 0.7
f (mm/rev)
Mild Steel
14
18
0.15
Nose
0.42
22
6
10
Flank
6
2
0 0.2 0.6 1.0 1.4
f (mm/rev)

14
22
0.42
6
Nose
23
0.43
10
Flank
6
2
0 0.2 0.6 1.0 1.4
f (mm/rev)

14
21
0.52
Nose
0.68
20
10
6
2
0 0.2 0.6 1.0 1.4
f (mm/rev)
First recommendation for rough cutting of cast iron
Cast Iron
Double sided flat insert.

Most effective for unstable machining due to its high edge strength.
Flank
20
7
5
For cast iron
Cast Iron

Can be used on workpieces requiring close tolerances due to G class
insert tolerance.
ap (mm)
For Cast Iron
Flat Top
0.32
18
1
0 0.1 0.3 0.5 0.7
f (mm/rev)
A050
ap (mm)

Covers the upper end of the heavy cutting region.
Wide land and large chamfer offer high edge strength.
A wide chipbreaker prevents chip jamming.
Nose
0.32
18
1
0 0.1 0.3 0.5 0.7
f (mm/rev)
ap (mm)
GJ
ap (mm)

For interrupted cuts and removing scale.
A combination of wide land and a large chip pocket allows high feed rates.
10
ap (mm)
For rough cutting of carbon steel, alloy steel and

stainless steel
ap (mm)
Rough Cutting
1
0 0.1 0.3 0.5 0.7
f (mm/rev)
GH
0.2
7
5
3
1
0 0.1 0.3 0.5 0.7
f (mm/rev)
0.68
Rhombic 55
Square 90
Triangular 60
CNMG_RS
DNMG_RS
SNMG_RS
TNMG_RS
WNMG_RS
^ A096
^ A103
^ A108
^ A115
^ A122
CNMG_GH
DNMG_GH
SNMG_GH
TNMG_GH
WNMG_GH
^ A097
^ A103
^ A109
^ A115
^ A123
CNMG_GJ
DNMG_GJ
WNMG_GJ
^ A097
^ A103
^ A123
CNMM_HZ
DNMM_HZ
SNMM_HZ
TNMM_HZ
^ A097
^ A103
^ A109
^ A115
CNMM_HX
SNMM_HX
^ A097
^ A109
CNMM_HV
SNMM_HV
^ A097
^ A109
Rhombic 35
Trigon 80
Round
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
RS
GH
GJ
HZ
HX
HV
CNMA
DNMA
SNMA
TNMA
WNMA
^ A097
^ A103
^ A109
^ A115
^ A123
DNGA
SNGA
TNGA
VNGA
^ A103
^ A109
^ A115
^ A118
Flat Top(M)
Flat Top(G)
A051
CLASSIFICATION
Breaker Name
and
Picture
First recommendation for finishing carbon steel and

alloy steel
Breaker protrusion at the corner tip controls chips even at small
depth of cut.
Maintains the edge strength at the corner and prevents sudden fractures.
FM
Finish Cutting
First recommendation for finishing stainless steel

Breaker protrusion at the corner tip controls chips even at small
depth of cut.
1
0
R/L-F
G
SV
Light cutting of carbon steel, alloy steel, mild steel

and stainless steel
Large rake angle provides sharp cutting action.
A peninsular dot ensures chip control at depths of cut under 1mm.
MP
First recommendation for medium cutting of carbon

steel and alloy steel
Good balance of wear resistance and fracture resistance because of
the flat land cutting edge.
A wide chip pocket controls increasing of the cutting resistance and
reduces vibration and chip jamming even at large depth of cut.
0.1 0.2 0.3 0.4

f (mm/rev)
Nose
18
ap (mm)
3
2
1
0
Flank
0.1 0.2 0.3 0.4
f (mm/rev)
Nose
Stainless Steel
18
ap (mm)
3
2
1
0
Flank
0.1 0.2 0.3 0.4
f (mm/rev)
Nose

18
3
2
1
Flank
0.1 0.2 0.3 0.4
f (mm/rev)
Cast Iron
Flank
ap (mm)

for general use.
13
18
0.1
0.1 0.2 0.3 0.4

f (mm/rev)

ap (mm)
Medium Cutting
A052
Flank
Flank
0.1 0.2 0.3 0.4
f (mm/rev)
MK
18
1
0
ap (mm)
Light Cutting
Sharp cutting edge due to a large rake angle.

Prevents welding of the insert and controls white turbidity of the surface finish.
Breaker protrusion suitable for depth of cut area achieves a wide
range of chip control.
Nose

Sharp cutting edge gives a good surface finish.
First recommendation for light cutting of stainless

steel

Breaker protrusion suitable for depth of cut area achieves a wide
range of chip control.
LM
Flank
0.1 0.2 0.3 0.4
f (mm/rev)
Finishing
First recommendation for light cutting of carbon

Nose
LP
ap (mm)
Suitable for low depths of cut and low feed rates.

Sharp cutting edge and low resistance design achieves excellent cutting
performance.
Flank
0.1 0.2 0.3 0.4
f (mm/rev)
Stainless Steel
ap (mm)

alloy steel, mild steel and stainless steel
FV
Nose

ap (mm)
FP
Cross Section
Geometry
Features
ap (mm)
Tolerance
5 POSITIVE INSERTS WITH HOLE

Application
TURNING INSERTS
TURNING INSERTS
18
0.1
Nose
2
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
18
0.1
Flank
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
VBMT_FP
Round
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
FP
^ A148
VBMT_FM
FM
^ A148
VBMT_FV
FV
^ A148
VBGT_R/L-F
WBGT_R/L-F
^ A148
^ A155
VBMT_LP
R/L-F
LP
^ A148
VBMT_LM
LM
^ A148
VBMT_SV
SV
^ A149
VBMT_MK
MK
^ A149
VBMT_MP
MP
^ A149
A053
CLASSIFICATION
MM
First recommendation for medium cutting of

stainless steel
Standard
Cross Section
Geometry
Features
Medium cutting of carbon steel, alloy steel and

stainless steel
Balance of edge strength and sharpness due to a combination of a
flat land and large rake angle.
Stainless Steel
ap (mm)
Breaker Name
and
Picture
A positive insert with a large rake angle achieves sharp cutting edge
performance.
The double breakers and round-shaped dots in the rake face achieve
a wide range of chip discharge.
R/L-MV
Medium cutting of carbon steel, alloy steel, mild steel

and stainless steel
R/L-SR
1
0.1 0.2 0.3 0.4
f (mm/rev)
0.1
18
Flank
Nose
0.1
10
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
18
0.1
20
10
0.16
8
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
Medium cutting of automatic lathe machining
A wide lead chipbreaker.

Insert designed for low resistance chip control.
20
0.16
Flank
Flank
3
2
Flank
Nose

3
Flank
Nose
18
30
1
0.1 0.2 0.3 0.4
f (mm/rev)
A parallel chipbreaker.
Excellent chip control for low to medium feed rates.
ap (mm)
Nose
R/L-SN
0.1
18
ap (mm)
Medium Cutting
A positive insert with a large rake angle achieves sharp cutting edge
performance.
The double breakers and round-shaped dots in the rake face achieve
0.1
18

ap (mm)
Medium cutting of carbon steel, alloy steel, mild steel

and stainless steel
ap (mm)
MV
0.1 0.2 0.3 0.4

f (mm/rev)
0.1
18
ap (mm)
Tolerance

Application
TURNING INSERTS
TURNING INSERTS
Flank
6
4
20
R/LW-SN
Excellent chip control for low to medium feed rates.
The wiper produces good cutting surface.
ap (mm)
0 0.1 0.3
f (mm/rev)
Flank
6
4
20
A054
Flat Top
M
Heavy cutting of cast iron
Cast Iron
Flat top.
ap (mm)
For Cast Iron
0 0.1 0.3
f (mm/rev)
2
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
VBMT_MM
Round
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
MM
^ A149
VBMT
Standard
^ A149
VBMT_MV
MV
^ A149
WBMT_R/L-MV
R/L-MV
^ A155
VBET_R/L-SR
R/L-SR
^ A150
VBET_R/L-SN
R/L-SN
^ A150
VBET_R/LW-SN
R/LW-SN
^ A150
VBMW
Flat Top(M)
^ A150
A055
CLASSIFICATION
Breaker Name
and
Picture
First recommendation for finishing carbon steel and

alloy steel
Breaker protrusion at the corner tip controls chips even at small depth
of cut.
FM
M
First recommendation for finishing stainless steel

Breaker protrusion at the corner tip controls chips even at small depth
of cut.
Finish Cutting
FJ
First recommendation for finishing difficult-to-cut

materials
1
0
LM
Flank
0.1 0.2 0.3 0.4
f (mm/rev)
Nose
14
2
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
Aluminium Alloy

30
2
1
0
0.1
0.3
f (mm/rev)
0.5
Flank
17
2
1
Lead chipbreaker.
Excellent chip control at low feed rates.
ap (mm)
0.1 0.2 0.3 0.4

f (mm/rev)
Finishing
Flank
15
2
1
0.1 0.2 0.3 0.4
f (mm/rev)
First recommendation for light cutting of carbon steel Carbon Steel Alloy Steel
3
and alloy steel
ap (mm)
Flank
Flank
Finishing
Nose
18
2
1
0
Flank
0.1 0.2 0.3 0.4
f (mm/rev)
First recommendation for light cutting of stainless steel Stainless Steel

Breaker protrusion suitable for depth of cut area achieves a wide range
of chip control.
ap (mm)
Light Cutting
A056
Nose
18
The high rake angle and 3D curved cutting edge provides sharpness
at the cutting point.
Additionally the 3D shape of the rake face enables excellent chip control.
Lapping of the top surface gives a mirror finish for improved welding
resistance.

Breaker protrusion suitable for depth of cut area achieves a wide range
of chip control.
LP
0.1 0.2 0.3 0.4

f (mm/rev)
R/L
Flank
G
R/L-F
Nose
ap (mm)
For aluminium alloy
ap (mm)
AZ
0.1 0.2 0.3 0.4

f (mm/rev)
Stainless Steel
ap (mm)

performance.
Flank
1
0
ap (mm)

FV
Nose

ap (mm)
FP
Cross Section
Geometry
Features
ap (mm)
Tolerance

Application
TURNING INSERTS
TURNING INSERTS
Nose
18
2
1
0
Flank
0.1 0.2 0.3 0.4
f (mm/rev)
Rhombic 55
Square 90
Triangular 60 Rhombic 35
CCMT_FP
DCMT_FP
SCMT_FP
TCMT_FP
VCMT_FP
^ A126
^ A132
^ A138
^ A141
^ A151
CCMT_FM
DCMT_FM
SCMT_FM
TCMT_FM
VCMT_FM
^ A126
^ A132
^ A138
^ A141
^ A151
CCMT_FV
DCMT_FV
SCMT_FV
TCMT_FV
VCMT_FV
^ A126
^ A132
^ A138
^ A141
^ A151
Trigon 80
Rhombic 25
Round
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
FP
FM
FV
CCGT_FJ
FJ
^ A126
CCGT_AZ
DCGT_AZ
TCGT_AZ
VCGT_AZ
RCGT_AZ
^ A126
^ A132
^ A141
^ A151
^ A137
CCGT_L-F DCGT_R/L-F
CCGH_R/L-F
^ A127
TCGT_R/L-F VCGT_R/L-F
^ A132
^ A141
AZ
R/L-F
^ A151
WCGT_R/L
R/L
^ A156
CCMT_LP
DCMT_LP
SCMT_LP
TCMT_LP
VCMT_LP
^ A127
^ A132
^ A138
^ A141
^ A151
CCMT_LM
DCMT_LM
SCMT_LM
TCMT_LM
VCMT_LM
^ A127
^ A133
^ A138
^ A142
^ A151
LP
LM
A057
CLASSIFICATION
Breaker Name
and
Picture
SVX
Cross Section
Geometry
Features
Light cutting of carbon steel and alloy steel

Chip control is improved by having a chip breaker geometry
suitable for copying.

Positive land improves sharpness.
Flank
Nose
0.12
20
12
2
1
0.1 0.2 0.3 0.4
f (mm/rev)
Light cutting of automatic lathe machining
Excellent chip control at low feed rates.
ap (mm)
0.1 0.2 0.3 0.4

f (mm/rev)
R/L-SS
Nose
18

ap (mm)
Wiper insert for light cutting of carbon steel,

Flank
SW
0.1 0.2 0.3 0.4

f (mm/rev)

ap (mm)

M
Light Cutting
Alternative chipbreaker for light cutting of carbon steel,

18
SV
Nose

ap (mm)
Tolerance

Application
TURNING INSERTS
TURNING INSERTS
16
0.12 Flank
8
Flank
6
4
14
2
0 0.1 0.3
f (mm/rev)

Medium Cutting
18

for general use.
1
0.1 0.2 0.3 0.4
f (mm/rev)
18
18
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
18
0.1
0.1
0.1
Cast Iron
2
18
ap (mm)
Nose
Flank
0.1
0.1 0.2 0.3 0.4

f (mm/rev)
18
0.1
Nose
2
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
18
0.1
Balance of edge strength and sharpness due to a combination of a

flat land and large rake angle.
Flank
Flank
0.2
15
A058
Flank
Flank
First recommendation for medium cutting of carbon steel,

alloy steel, mild steel, stainless steel and cast iron
Nose
Standard
0.1
First recommendation for medium cutting of stainless Stainless Steel

steel
3
MK
ap (mm)
MM

ap (mm)
First recommendation for medium cutting of carbon

ap (mm)
MP
Rhombic 55
Square 90
Triangular 60 Rhombic 35
Trigon 80
Rhombic 25
Round
XCMT_SVX
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
SVX
^ A158
CCMH_SV
DCMT_SV
VCMT_SV
^ A127
^ A133
^ A152
SV
CCMT_SW
SW
^ A127
CCGT_R/L-SS DCGT_R/L-SS
R/L-SS
^ A127
^ A133
CCMT_MP
DCMT_MP
SCMT_MP
TCMT_MP
VCMT_MP
^ A128
^ A133
^ A138
^ A142
^ A152
CCMT_MM
DCMT_MM
SCMT_MM
TCMT_MM
VCMT_MM
^ A128
^ A133
^ A139
^ A142
^ A152
CCMT_MK
DCMT_MK
SCMT_MK
TCMT_MK
VCMT_MK
^ A128
^ A133
^ A138
^ A142
^ A152
CCMT
DCMT
SCMT
TCMT
VCMT
WCMT
RCMT
^ A128
^ A133
^ A139
^ A142
^ A152
^ A156
^ A137
MP
MM
MK
Standard
RCMX
^ A137
A059
CLASSIFICATION
MV
Alternative chipbreaker for medium cutting of carbon steel,

A positive insert and the large rake angle achieve sharp cutting edge
performance.
The double breakers and round shape in the rake face achieve
M
MW
Cross Section
Geometry
Features
Wiper insert for medium cutting of carbon steel,

A wide chip pocket prevents chip jamming.
0.18
20
Flank
12
Nose
0.2
18
7
2
1
A wide lead chipbreaker.

Insert designed for low resistance chip control.
ap (mm)
0.1 0.2 0.3 0.4

f (mm/rev)
0.2
18
Flank
Flank
30
Suitable for precise machining with E class tolerance.
ap (mm)
0.1 0.2 0.3 0.4

f (mm/rev)
Flank
6
4
20
2
0 0.1 0.3
f (mm/rev)
R/L-SN
G
ap (mm)
Medium Cutting
0.1 0.2 0.3 0.4

f (mm/rev)
R/L-SN
12
0.18
20
R/L-SR
Nose

ap (mm)
Breaker Name
and
Picture
ap (mm)
Tolerance

Application
TURNING INSERTS
TURNING INSERTS
Flank
6
4
20
R/LW-SN
E
The wiper produces a good surface finish.
ap (mm)
0 0.1 0.3
f (mm/rev)
Flank
6
4
20
Heavy Cutting
A060
RR
M
3D moulded chipbreaker provides good chip control.

G class insert gives sharp cutting action,
ap (mm)
SMG
Heavy cutting of carbon steel and alloy steel
A wide groove chipbreaker prevents chips

from jamming at large depths of cut.
Small dimples improve chip control at small depths of cut.
ap (mm)
0 0.1 0.3
f (mm/rev)
Nose
14
3
2
1
0
Flank
0.1 0.2 0.3 0.4
f (mm/rev)
12
8
4
0 0.2 0.6 1.0 1.4
f (mm/rev)
28
0.3
Rhombic 55
Square 90
Triangular 60
Rhombic 35
CCMH_MV
DCMT_MV
VCMT_MV
^ A128
^ A134
^ A152
Trigon 80
Round
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
MV
CCMT_MW
MW
^ A129
CCET_R/L-SR DCET_R/L-SR
^ A129
R/L-SR
^ A134
CCET_R/L-SN DCET_R/L-SN
^ A129
R/L-SN(E)
^ A134
CCGT_R/L-SN DCGT_R/L-SN
^ A130
R/L-SN(G)
^ A135
CCET_R/LW-SN DCET_R/LW-SN
^ A130
^ A135
CCGT_SMG
DCGT_SMG
^ A130
^ A135
R/LW-SN
SMG
RCMX_RR
RR
^ A137
A061
CLASSIFICATION
Breaker Name
and
Picture
Flat Top
For Cast Iron
Cross Section
Geometry
Features
Cast Iron
Flat top.
ap (mm)
Tolerance
1
0
Flat Top
G
0.1 0.2 0.3 0.4

f (mm/rev)
For cast iron
Cast Iron
Flat top.
Can be used on workpieces requiring close tolerances
due to G class insert tolerance.
ap (mm)
Application
TURNING INSERTS
TURNING INSERTS
2
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
Breaker Name
and
Picture
R/L-FS
G
Alternative chipbreaker for finishing carbon steel,

alloy steel, stainless steel, cast iron and
aluminium alloy
Small wide lead chipbreaker.
R/L-F
M
Flank
3
2
15
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
Finishing

Flank
3
2
15

ap (mm)
0.1 0.2 0.3 0.4

f (mm/rev)
Finishing
Flank
3
2
15
1
0.1 0.2 0.3 0.4
f (mm/rev)
Finishing

Good chip control for low to medium feed rates.
Flank
3
2
10
Aluminium Alloy

ap (mm)
0.1 0.2 0.3 0.4

f (mm/rev)
Finishing
Flank
3
2
25
1
0
A062
Standard
0.1 0.2 0.3 0.4

f (mm/rev)
ap (mm)
Flank
R/L
18
R/L-F
Nose

ap (mm)

performance.
Finish Cutting

ap (mm)
FV
Cross Section
Geometry
Features
ap (mm)
Tolerance
Application
0.1 0.2 0.3 0.4

f (mm/rev)
Rhombic 55
Square 90
Triangular 60
Rhombic 35
CCMW
DCMW
SCMW
TCMW
VCMW
^ A130
^ A135
^ A139
^ A143
^ A152
CCGW
DCGW
^ A130
^ A135
Rhombic 80
Rhombic 55
Trigon 80
Round
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
Flat Top(M)
Flat Top(G)
Square 90
Triangular 60
CPMH_FV
TPMH_FV
^ A131
^ A145
Rhombic 35
Trigon 80
Breaker Name
and
Cross Section
FV
TPGH_R/L-FS
WPGT_R/L-FS
^ A145
^ A157
CPMH_R/L-F
Round
R/L-FS
R/L-F(M)
^ A131
CPGT_R/L-F
R/L-F(G)
^ A131
TPGX_R/L
R/L
^ A146
CPGT
Standard
^ A131
A063
CLASSIFICATION
Breaker Name
and
Picture
L
M
Cross Section
Geometry
Features
Finishing

ap (mm)
Tolerance

Application
TURNING INSERTS
TURNING INSERTS

ap (mm)
3D moulded chipbreaker provides good chip control.

G class insert gives sharp cutting action,
First recommendation for light cutting of carbon steel,

First recommendation for medium cutting of carbon steel,

For Cast Iron
11
Nose
18
2
1
Flank
0.1 0.2 0.3 0.4
f (mm/rev)

3
Nose
10
Flank
1
0.1 0.2 0.3 0.4
f (mm/rev)
10
0.2
20
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
Cast Iron
Flat top.
1
0.1 0.2 0.3 0.4
f (mm/rev)
For cast iron
Cast Iron
Flat top.
Can be used on workpieces requiring close tolerances
due to G class insert tolerance.
2
1
0.1 0.2 0.3 0.4
f (mm/rev)
0.2
20
Nose
Flat Top
0.1 0.2 0.3 0.4

f (mm/rev)
ap (mm)
A positive insert and large rake angle achieves sharp cutting edge
performance.
Double breakers in the rake face achieve a wide range of chip discharge.
Flank
ap (mm)
Medium Cutting
Nose
11
ap (mm)
Alternative chipbreaker for medium cutting of carbon steel,

alloy steel and stainless steel
Standard, general purpose chipbreaker.
Flat Top
0.1 0.2 0.3 0.4

f (mm/rev)
MV
15

Standard
A064
ap (mm)
SV
Flank
ap (mm)
Light Cutting
SMG
0.1 0.2 0.3 0.4

f (mm/rev)
Finishing
ap (mm)
Finish Cutting
10
1
0
SRF
Flank
Flank
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
TPMX_L
Round
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
^ A146
VPET_R/L-SRF
SRF
^ A154
VPGT_SMG
SMG
^ A154
CPMH_SV
TPMH_SV
^ A131
^ A146
CPMX
SPMT
TPMX
^ A131
^ A140
^ A146
SV
Standard
CPMH_MV
TPMH_MV
WPMT_MV
^ A131
^ A147
^ A157
SPMW
MV
Flat Top(M)
^ A140
SPGX
TPGX
^ A140
^ A147
Flat Top(G)
A065
CLASSIFICATION
Breaker Name
and
Picture
R/L
G
Cross Section
Geometry
Features
For aluminium alloy cutting
Aluminium Alloy
Lead chipbreaker.
ap (mm)
Tolerance

For Aluminium Alloy Application
TURNING INSERTS
TURNING INSERTS
Flank
3
2
20
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
Breaker Name
and
Picture
Aluminium Alloy
Lead chipbreaker.
R/L
20
1
0
Flank
0.1 0.2 0.3 0.4

f (mm/rev)
Aluminium Alloy
Good chip control for medium feed rates.
ap (mm)
For Aluminium Alloy
R/L-F
Cross Section
Geometry
Features
ap (mm)
Tolerance
Application
Flank
25
2
1
0
0.1
0.3
f (mm/rev)
A066
0.5
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
Round
VDGX_R/L
Breaker Name
and
Cross Section
TURNING INSERTS
Rhombic 80
R/L
^ A153
Rhombic 80
Rhombic 55
Square 90
Triangular 60
DEGX_R/L-F
Rhombic 35
Trigon 80
Round
Breaker Name
and
Cross Section
R/L-F
^ A136
DEGX_R/L
TEGX_R/L
^ A136
^ A144
R/L
A067
CLASSIFICATION
Breaker Name
and
Picture
For Cast Iron
Flat Top
G
Cast Iron

Most effective for unstable machining due to high edge
strength and stable insert clamping.
ap (mm)
Flat Top
Cross Section
Geometry
Features
For cast iron
Cast Iron

insert tolerance.
ap (mm)
Tolerance

Application
TURNING INSERTS
TURNING INSERTS
5
3
1
0 0.1 0.3 0.5 0.7
f (mm/rev)
5
3
1
0 0.1 0.3 0.5 0.7
f (mm/rev)
Tolerance
Breaker Name
and
Picture
Flat Top
G
Cross Section
Geometry
Features
For cast iron
Cast Iron

insert tolerance.
ap (mm)
For Cast Iron
Application
7 POSITIVE INSERTS WITHOUT HOLE
2
1
0
0.1 0.2 0.3 0.4
f (mm/rev)
R/L
G
Finishing
Light to medium cutting of carbon steel, alloy steel

and stainless steel
Standard, general purpose chipbreaker.
Flank
0.1 0.2 0.3 0.4
f (mm/rev)
Cast Iron
Flat top.
ap (mm)
For Cast Iron
Nose
0
2
1
0
Flat Top
0.1 0.2 0.3 0.4

f (mm/rev)
15

ap (mm)
Standard
Flank
Flat Top
A068
Cross Section
Geometry
Features
ap (mm)
Tolerance
Breaker Name
and
Picture
0.1 0.2 0.3 0.4

f (mm/rev)
For cast iron
Cast Iron
Flat top.
insert tolerance.
ap (mm)
Light to Medium Cutting
Finish Cutting
Application
2
1
0
0.1 0.2 0.3 0.4

f (mm/rev)
SNMN
TNMN
^ A124
^ A125
SNGN
TNGN
^ A124
^ A125
Square 90
Triangular 60
TCGN
Flat Top(M)
Tool Holder Type
TURNING INSERTS
Breaker Name
and
Cross Section
Tolerance
Triangular 60
Inserts
RTG
Special
Square 90
Application
SPECIAL PURPOSE INSERTS
TL Type
^ A159
Flat Top(G)
Breaker Name
and
Cross Section
Flat Top
^ A161
Square 90
Triangular 60
SPGR_R
TPGR_R/L
^ A160
^ A162
SPMR
TPMR
^ A160
^ A162
SPMN
TPMN
^ A160
^ A162
SPGN
TPGN
^ A160
^ A162
Breaker Name
and
Cross Section
R/L
Standard
Flat Top(M)
Flat Top(G)
A069
TURNING INSERTS
TURNING INSERTS
RECOMMENDED CUTTING CONDITIONS
y NEGATIVE INSERTS
Work Material
Breker :
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Mild Steel
(ASTM A36, AISI 1010)

(AISI 1045, AISI 4140)
< 180HB
180
|
280HB
FY
VP25N
285 445
0.09 0.23
0.20 0.80
FS
NX2525
270 385
0.09 0.23
0.20 0.70
SY
VP25N
260 405
0.16 0.33
0.50 1.20
FY
MP3025
275 420
0.09 0.23
0.20 0.80
FY
NX3035
260 370
0.09 0.23
0.20 0.80
FS
NX2525
270 385
0.09 0.23
0.20 0.70
SY
MP3025
250 385
0.16 0.33
0.50 1.20
SY
NX3035
235 335
0.16 0.33
0.50 1.20
FY
UE6020
285 460
0.09 0.23
0.20 0.80
FS
UE6020
285 460
0.09 0.23
0.20 0.70
SY
UE6020
260 420
0.16 0.33
0.50 1.20
FH
AP25N
215 340
0.08 0.20
0.20 1.00
FH
NX2525
205 295
0.08 0.20
0.20 1.00
R/L-F
MP3025
210 325
0.05 0.15
0.10 0.50
PK
NX2525
195 280
0.10 0.30
0.20 1.00
LP
UE6105
220 405
0.10 0.40
0.30 2.00
SH
UE6105
220 405
0.10 0.40
0.30 2.00
LP
MP3025
195 295
0.10 0.40
0.30 2.00
SH
AP25N
200 315
0.10 0.40
0.30 2.00
SH
NX2525
190 270
0.10 0.40
0.30 2.00
SA
UE6105
220 405
0.10 0.40
0.30 2.00
SW
UE6105
220 405
0.10 0.50
0.30 2.50
SW
MP3025
195 295
0.10 0.50
0.30 2.50
SW
NX2525
190 270
0.10 0.50
0.30 2.50
10
R/L-K
MP3025
195 295
0.08 0.20
0.30 1.20
MP
UE6105
200 370
0.16 0.50
0.30 4.00
MP
MP3025
175 270
0.16 0.50
0.30 4.00
MA
UE6105
200 370
0.20 0.50
0.30 4.00
MH
UE6105
200 370
0.20 0.55
1.00 4.00
Std
UE6105
200 370
0.25 0.60
1.50 5.00
Std
MP3025
175 270
0.25 0.60
1.50 5.00
Std
NX2525
170 245
0.25 0.60
1.50 5.00
Std
UTi20T
85 125
0.25 0.60
1.50 5.00
MW
UE6105
200 370
0.20 0.60
0.90 4.00
10
R/L
MP3025
175 270
0.15 0.32
0.40 2.00
RP
UE6105
190 350
0.25 0.60
1.50 6.00
GH
UE6105
190 350
0.25 0.60
1.50 6.00
HX
UE6110
160 275
0.50 1.26
3.00 11.00
HV
UE6110
135 225
0.70 1.30
4.00 12.00
FH
MP3025
210 325
0.08 0.20
0.20 1.00
FH
NX3035
200 285
0.08 0.20
0.20 1.00
FH
UE6110
230 390
0.08 0.20
0.20 1.00
LP
MC6015
210 355
0.10 0.40
0.30 2.00
LP
UE6110
210 355
0.10 0.40
0.30 2.00
SH
UE6110
210 355
0.10 0.40
0.30 2.00
SA
UE6110
210 355
0.10 0.40
0.30 2.00
LP
MP3025
195 295
0.10 0.40
0.30 2.00
CUTTING CONDITIONS :
: Stable Cutting
: General Cutting
: Unstable Cutting
CUTTING AREA : F : Finish Cutting L : Light Cutting M : Medium Cutting R : Rough Cutting H : Heavy Cutting
A070
Std : Standard Flat : Flat Top
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)

(S45C, SCM440)
180
|
280HB
SH
NX3035
185 260
0.10 0.40
0.30 2.00
SA
NX3035
185 260
0.10 0.40
0.30 2.00
SW
UE6110
210 355
0.10 0.50
0.30 2.50
SW
NX3035
185 260
0.10 0.50
0.30 2.50
MP
MC6015
190 325
0.16 0.50
0.30 4.00
MP
UE6110
190 325
0.16 0.50
0.30 4.00
MA
MC6015
190 325
0.20 0.50
0.30 4.00
MA
UE6110
190 325
0.20 0.50
0.30 4.00
MA
NX3035
165 235
0.20 0.50
0.30 4.00
MH
MC6015
190 325
0.20 0.55
1.00 4.00
MH
UE6110
190 325
0.20 0.55
1.00 4.00
Std
UE6110
190 325
0.25 0.60
1.50 5.00
Std
NX3035
165 235
0.25 0.60
1.50 5.00
10
MW
MC6015
190 325
0.20 0.60
0.90 4.00
11
MW
UE6110
190 325
0.20 0.60
0.90 4.00
RP
MC6015
180 310
0.25 0.60
1.50 6.00
RP
UE6110
180 310
0.25 0.60
1.50 6.00
GH
UE6110
180 310
0.25 0.60
1.50 6.00
HX
UE6020
155 250
0.50 1.26
3.00 11.00
HV
UE6020
125 205
0.70 1.30
4.00 12.00
HZ
UE6110
160 275
0.40 1.20
2.00 10.00
FH
UE6110
230 390
0.08 0.20
0.20 1.00
FH
UE6020
215 355
0.08 0.20
0.20 1.00
LP
MC6025
210 340
0.10 0.40
0.30 2.00
SH
UE6020
200 325
0.10 0.40
0.30 2.00
SA
UE6020
200 325
0.10 0.40
0.30 2.00
MP
MC6025
190 310
0.16 0.50
0.30 4.00
MA
MC6025
190 310
0.20 0.50
0.30 4.00
MP
UE6020
180 295
0.16 0.50
0.30 4.00
MA
UE6020
180 295
0.20 0.50
0.30 4.00
MA
UE6035
170 235
0.20 0.50
0.30 4.00
MH
UE6020
180 295
0.20 0.55
1.00 4.00
MH
UE6035
170 235
0.20 0.55
1.00 4.00
Std
UE6020
180 295
0.25 0.60
1.50 5.00
Std
UE6035
170 235
0.25 0.60
1.50 5.00
10
MW
MC6025
190 310
0.20 0.60
0.90 4.00
11
MW
UE6020
180 295
0.20 0.60
0.90 4.00
RP
MC6025
180 295
0.25 0.60
1.50 6.00
GH
UE6020
170 280
0.25 0.60
1.50 6.00
HX
UH6400
135 195
0.50 1.26
3.00 11.00
HV
UH6400
110 160
0.70 1.30
4.00 12.00
HZ
UH6400
135 195
0.40 1.20
2.00 10.00
HZ
UE6020
155 250
0.40 1.20
2.00 10.00
TURNING INSERTS
Work Material
A071
TURNING INSERTS
TURNING INSERTS
y NEGATIVE INSERTS
Work Material
Breker :
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Austenitic
Stainless Steel
(AISI 304, AISI 316)
Austenitic
Stainless Steel
(AISI 304LN, AISI 316LN)
< 200HB
>200HB
LM
MC7015
180 285
0.10 0.30
0.30 2.00
SH
US735
95 185
0.10 0.40
0.30 2.00
SH
NX2525
65 135
0.10 0.40
0.30 2.00
SW
US7020
105 270
0.10 0.50
0.30 2.50
MM
MC7015
160 255
0.15 0.45
0.70 5.00
GM
MC7015
160 255
0.16 0.50
0.50 4.00
MS
US7020
95 245
0.16 0.50
0.50 4.00
MA
US7020
95 245
0.20 0.50
0.30 4.00
MH
US7020
95 245
0.20 0.55
1.00 4.00
MW
US7020
95 245
0.20 0.60
0.90 4.00
RM
MC7015
155 245
0.25 0.55
1.50 6.00
GH
US7020
90 235
0.25 0.60
1.50 6.00
LM
MC7025
160 215
0.10 0.30
0.30 2.00
SH
US735
95 185
0.10 0.40
0.30 2.00
MM
MC7025
145 195
0.15 0.45
0.70 5.00
GM
MC7025
145 195
0.16 0.50
0.50 4.00
MA
MC7025
145 195
0.20 0.50
0.30 4.00
MS
US735
85 165
0.16 0.50
0.50 4.00
MA
US735
85 165
0.20 0.50
0.30 4.00
RM
MC7025
140 185
0.25 0.55
1.50 6.00
GH
US735
85 160
0.25 0.60
1.50 6.00
LM
MP7035
95 155
0.10 0.30
0.30 2.00
SH
US735
95 185
0.10 0.40
0.30 2.00
MM
MP7035
85 140
0.15 0.45
0.70 5.00
GM
MP7035
85 140
0.16 0.50
0.50 4.00
MA
MP7035
85 140
0.20 0.50
0.30 4.00
MS
US735
85 165
0.16 0.50
0.50 4.00
MS
VP15TF
75 130
0.16 0.50
0.50 4.00
MS
UP20M
95 145
0.16 0.50
0.50 4.00
MS
UTi20T
75 110
0.16 0.50
0.50 4.00
MA
VP15TF
75 130
0.20 0.50
0.30 4.00
Std
VP15TF
75 130
0.25 0.60
1.50 5.00
RM
MP7035
85 135
0.25 0.55
1.50 6.00
GH
US735
85 160
0.25 0.60
1.50 6.00
LM
MC7015
150 240
0.10 0.30
0.30 2.00
SH
US735
80 155
0.10 0.40
0.30 2.00
SH
NX2525
55 115
0.10 0.40
0.30 2.00
SW
US7020
90 230
0.10 0.50
0.30 2.50
MM
MC7015
135 215
0.15 0.45
0.70 5.00
GM
MC7015
135 215
0.16 0.50
0.50 4.00
MS
US7020
80 205
0.16 0.50
0.50 4.00
MA
US7020
80 205
0.20 0.50
0.30 4.00
MH
US7020
80 205
0.20 0.55
1.00 4.00
MW
US7020
80 205
0.20 0.60
0.90 4.00
RM
MC7015
130 205
0.25 0.55
1.50 6.00
GH
US7020
75 195
0.25 0.60
1.50 6.00
LM
MC7025
135 180
0.10 0.30
0.30 2.00
: Stable Cutting
: General Cutting
: Unstable Cutting
A072
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Austenitic
Stainless Steel
Two-phase Stainless Steel

(AISI 329)
>200HB
< 280HB
SH
US735
80 155
0.10 0.40
0.30 2.00
MM
MC7025
125 165
0.15 0.45
0.70 5.00
GM
MC7025
125 165
0.16 0.50
0.50 4.00
MA
MC7025
125 165
0.20 0.50
0.30 4.00
MS
US735
75 140
0.16 0.50
0.50 4.00
MA
US735
75 140
0.20 0.50
0.30 4.00
RM
MC7025
115 155
0.25 0.55
1.50 6.00
GH
US735
70 135
0.25 0.60
1.50 6.00
LM
MP7035
80 130
0.10 0.30
0.30 2.00
SH
US735
80 155
0.10 0.40
0.30 2.00
MM
MP7035
75 120
0.15 0.45
0.70 5.00
GM
MP7035
75 120
0.16 0.50
0.50 4.00
MA
MP7035
75 120
0.20 0.50
0.30 4.00
MS
US735
75 140
0.16 0.50
0.50 4.00
MS
VP15TF
65 110
0.16 0.50
0.50 4.00
MS
UP20M
80 125
0.16 0.50
0.50 4.00
MS
UTi20T
65 95
0.16 0.50
0.50 4.00
MA
VP15TF
65 110
0.20 0.50
0.30 4.00
Std
VP15TF
65 110
0.25 0.60
1.50 5.00
RM
MP7035
70 115
0.25 0.55
1.50 6.00
GH
US735
70 135
0.25 0.60
1.50 6.00
LM
MC7015
120 195
0.10 0.30
0.30 2.00
SH
US735
65 125
0.10 0.40
0.30 2.00
SH
NX2525
45 90
0.10 0.40
0.30 2.00
SW
US7020
75 185
0.10 0.50
0.30 2.50
MM
MC7015
110 175
0.15 0.45
0.70 5.00
GM
MC7015
110 175
0.16 0.50
0.50 4.00
MS
US7020
65 170
0.16 0.50
0.50 4.00
MA
US7020
65 170
0.20 0.50
0.30 4.00
MH
US7020
65 170
0.20 0.55
1.00 4.00
MW
US7020
65 170
0.20 0.60
0.90 4.00
RM
MC7015
105 165
0.25 0.55
1.50 6.00
GH
US7020
60 160
0.25 0.60
1.50 6.00
LM
MC7025
110 150
0.10 0.30
0.30 2.00
SH
US735
65 125
0.10 0.40
0.30 2.00
MM
MC7025
100 135
0.15 0.45
0.70 5.00
GM
MC7025
100 135
0.16 0.50
0.50 4.00
MA
MC7025
100 135
0.20 0.50
0.30 4.00
MS
US735
60 115
0.16 0.50
0.50 4.00
MA
US735
60 115
0.20 0.50
0.30 4.00
RM
MC7025
95 125
0.25 0.55
1.50 6.00
GH
US735
55 110
0.25 0.60
1.50 6.00
LM
MP7035
65 105
0.10 0.30
0.30 2.00
SH
US735
65 125
0.10 0.40
0.30 2.00
MM
MP7035
60 95
0.15 0.45
0.70 5.00
GM
MP7035
60 95
0.16 0.50
0.50 4.00
MA
MP7035
60 95
0.20 0.50
0.30 4.00
TURNING INSERTS
Work Material
A073
TURNING INSERTS
TURNING INSERTS
y NEGATIVE INSERTS
Work Material
Breker :
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)

(AISI 329)
Ferritic and Martensitic

Stainless Steel

Stainless Steel
< 280HB
< 200HB
>200HB
MS
US735
60 115
0.16 0.50
0.50 4.00
MS
VP15TF
50 90
0.16 0.50
0.50 4.00
MS
UP20M
65 100
0.16 0.50
0.50 4.00
MS
UTi20T
50 75
0.16 0.50
0.50 4.00
MA
VP15TF
50 90
0.20 0.50
0.30 4.00
Std
VP15TF
50 90
0.25 0.60
1.50 5.00
RM
MP7035
55 90
0.25 0.55
1.50 6.00
GH
US735
55 110
0.25 0.60
1.50 6.00
LM
MC7015
180 285
0.10 0.30
0.30 2.00
SH
US735
95 185
0.10 0.40
0.30 2.00
SH
NX2525
65 135
0.10 0.40
0.30 2.00
SW
US7020
105 270
0.10 0.50
0.30 2.50
MM
MC7015
160 255
0.15 0.45
0.70 5.00
GM
MC7015
160 255
0.16 0.50
0.50 4.00
MS
US7020
95 245
0.16 0.50
0.50 4.00
MA
US7020
95 245
0.20 0.50
0.30 4.00
MH
US7020
95 245
0.20 0.55
1.00 4.00
MW
US7020
95 245
0.20 0.60
0.90 4.00
RM
MC7015
155 245
0.25 0.55
1.50 6.00
GH
US7020
90 235
0.25 0.60
1.50 6.00
LM
MC7025
160 215
0.10 0.30
0.30 2.00
SH
US735
95 185
0.10 0.40
0.30 2.00
MM
MC7025
145 195
0.15 0.45
0.70 5.00
GM
MC7025
145 195
0.16 0.50
0.50 4.00
MA
MC7025
145 195
0.20 0.50
0.30 4.00
MS
US735
85 165
0.16 0.50
0.50 4.00
MA
US735
85 165
0.20 0.50
0.30 4.00
RM
MC7025
140 185
0.25 0.55
1.50 6.00
GH
US735
85 160
0.25 0.60
1.50 6.00
LM
MP7035
95 155
0.10 0.30
0.30 2.00
SH
US735
95 185
0.10 0.40
0.30 2.00
MM
MP7035
85 140
0.15 0.45
0.70 5.00
GM
MP7035
85 140
0.16 0.50
0.50 4.00
MA
MP7035
85 140
0.20 0.50
0.30 4.00
MS
US735
85 165
0.16 0.50
0.50 4.00
MS
VP15TF
75 130
0.16 0.50
0.50 4.00
MS
UP20M
95 145
0.16 0.50
0.50 4.00
MS
UTi20T
75 110
0.16 0.50
0.50 4.00
MA
VP15TF
75 130
0.20 0.50
0.30 4.00
Std
VP15TF
75 130
0.25 0.60
1.50 5.00
RM
MP7035
85 135
0.25 0.55
1.50 6.00
GH
US735
85 160
0.25 0.60
1.50 6.00
LM
MC7015
150 240
0.10 0.30
0.30 2.00
SH
US735
80 155
0.10 0.40
0.30 2.00
SH
NX2525
55 115
0.10 0.40
0.30 2.00
SW
US7020
90 230
0.10 0.50
0.30 2.50
MM
MC7015
135 215
0.15 0.45
0.70 5.00
: Stable Cutting
: General Cutting
: Unstable Cutting
A074
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)

Stainless Steel
Hardened Stainless Steel

>200HB
<450HB
GM
MC7015
135 215
0.16 0.50
0.50 4.00
MS
US7020
80 205
0.16 0.50
0.50 4.00
MA
US7020
80 205
0.20 0.50
0.30 4.00
MH
US7020
80 205
0.20 0.55
1.00 4.00
MW
US7020
80 205
0.20 0.60
0.90 4.00
RM
MC7015
130 205
0.25 0.55
1.50 6.00
GH
US7020
75 195
0.25 0.60
1.50 6.00
LM
MC7025
135 180
0.10 0.30
0.30 2.00
SH
US735
80 155
0.10 0.40
0.30 2.00
MM
MC7025
125 165
0.15 0.45
0.70 5.00
MS
MC7025
125 165
0.16 0.50
0.50 4.00
MA
MC7025
125 165
0.20 0.50
0.30 4.00
MS
US735
75 140
0.16 0.50
0.50 4.00
MA
US735
75 140
0.20 0.50
0.30 4.00
RM
MC7025
115 155
0.25 0.55
1.50 6.00
GH
US735
70 135
0.25 0.60
1.50 6.00
LM
MP7035
80 130
0.10 0.30
0.30 2.00
SH
US735
80 155
0.10 0.40
0.30 2.00
MM
MP7035
75 120
0.15 0.45
0.70 5.00
GM
MP7035
75 120
0.16 0.50
0.50 4.00
MA
MP7035
75 120
0.20 0.50
0.30 4.00
MS
US735
75 140
0.16 0.50
0.50 4.00
MS
VP15TF
65 110
0.16 0.50
0.50 4.00
MS
UP20M
80 125
0.16 0.50
0.50 4.00
MS
UTi20T
65 95
0.16 0.50
0.50 4.00
MA
VP15TF
65 110
0.20 0.50
0.30 4.00
Std
VP15TF
65 110
0.25 0.60
1.50 5.00
RM
MP7035
70 115
0.25 0.55
1.50 6.00
GH
US735
70 135
0.25 0.60
1.50 6.00
LM
MC7015
100 160
0.10 0.30
0.30 2.00
SH
US735
55 105
0.10 0.40
0.30 2.00
SH
NX2525
35 75
0.10 0.40
0.30 2.00
SW
US7020
60 155
0.10 0.50
0.30 2.50
MM
MC7015
90 145
0.15 0.45
0.70 5.00
GM
MC7015
90 145
0.16 0.50
0.50 4.00
MS
US7020
55 140
0.16 0.50
0.50 4.00
MA
US7020
55 140
0.20 0.50
0.30 4.00
MH
US7020
55 140
0.20 0.55
1.00 4.00
MW
US7020
55 140
0.20 0.60
0.90 4.00
RM
MC7015
85 135
0.25 0.55
1.50 6.00
GH
US7020
50 130
0.25 0.60
1.50 6.00
LM
MC7025
90 120
0.10 0.30
0.30 2.00
SH
US735
55 105
0.10 0.40
0.30 2.00
MM
MC7025
80 110
0.15 0.45
0.70 5.00
GM
MC7025
80 110
0.16 0.50
0.50 4.00
MA
MC7025
80 110
0.20 0.50
0.30 4.00
MS
US735
50 95
0.16 0.50
0.50 4.00
TURNING INSERTS
Work Material
A075
TURNING INSERTS
TURNING INSERTS
y NEGATIVE INSERTS
Work Material
Breker :
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)

<450HB
MA
US735
50 95
0.20 0.50
0.30 4.00
RM
MC7025
80 105
0.25 0.55
1.50 6.00
GH
US735
45 90
0.25 0.60
1.50 6.00
LM
MP7035
55 85
0.10 0.30
0.30 2.00
SH
US735
55 105
0.10 0.40
0.30 2.00
MM
MP7035
50 80
0.15 0.45
0.70 5.00
GM
MP7035
50 80
0.16 0.50
0.50 4.00
MA
MP7035
50 80
0.20 0.50
0.30 4.00
MS
US735
50 95
0.16 0.50
0.50 4.00
MS
VP15TF
45 75
0.16 0.50
0.50 4.00
MS
UP20M
55 80
0.16 0.50
0.50 4.00
MS
UTi20T
45 60
0.16 0.50
0.50 4.00
MA
VP15TF
45 75
0.20 0.50
0.30 4.00
Std
VP15TF
45 75
0.25 0.60
1.50 5.00
RM
MP7035
45 75
0.25 0.55
1.50 6.00
GH
US735
45 90
0.25 0.60
1.50 6.00
: Stable Cutting
: General Cutting
: Unstable Cutting
A076
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Gray Cast Iron

(FC300)
< 350MPa
LK
MC5005
235 375
0.10 0.40
0.30 2.00
MA
MC5005
210 335
0.20 0.50
0.30 4.00
MA
UC5105
170 315
0.20 0.50
0.30 4.00
MK
MC5005
210 335
0.20 0.55
1.00 4.00
GK
MC5005
210 335
0.25 0.60
1.50 5.00
Std
UC5105
170 315
0.25 0.60
1.50 5.00
Std
NX2525
155 210
0.25 0.60
1.50 5.00
MW
UC5105
170 315
0.20 0.60
0.90 4.00
RK
MC5005
195 315
0.25 0.60
1.50 6.00
Flat
MC5005
195 315
0.25 0.60
2.50 6.00
GH
UC5105
165 300
0.25 0.60
1.50 6.00
Flat
UC5105
165 300
0.20 0.60
2.50 6.00
Flat
HTi10
100 145
0.20 0.60
2.50 6.00
Flat
HTi05T
110 185
0.20 0.60
2.50 6.00
Flat
MC5005
195 315
0.20 0.60
2.50 6.00
Flat
UC5105
165 300
0.20 0.60
2.50 6.00
LK
MC5015
205 335
0.10 0.40
0.30 2.00
MA
MC5015
190 305
0.20 0.50
0.30 4.00
MA
UC5115
165 305
0.20 0.50
0.30 4.00
MP
UC5115
165 305
0.16 0.50
0.30 4.00
SW
UC5115
185 335
0.10 0.50
0.30 2.50
MK
MC5015
190 305
0.20 0.55
1.00 4.00
GK
MC5015
190 305
0.25 0.60
1.50 5.00
Std
UC5115
165 305
0.25 0.60
1.50 5.00
Std
HTi10
105 150
0.25 0.60
1.50 5.00
MH
UC5115
165 305
0.20 0.55
1.00 4.00
MW
UC5115
165 305
0.20 0.60
0.90 4.00
RK
MC5015
180 285
0.25 0.60
1.50 6.00
Flat
MC5015
180 285
0.20 0.60
2.50 6.00
GH
UC5115
160 290
0.25 0.60
1.50 6.00
Flat
UC5115
160 290
0.20 0.60
2.50 6.00
Flat
MC5015
180 285
0.20 0.60
2.50 6.00
Flat
UC5115
160 290
0.20 0.60
2.50 6.00
LK
MC5015
205 335
0.10 0.40
0.30 2.00
MA
MC5015
190 305
0.20 0.50
0.30 4.00
MA
UC5115
165 305
0.20 0.50
0.30 4.00
MK
MC5015
190 305
0.20 0.55
1.50 4.00
GK
MC5015
190 305
0.25 0.60
1.50 5.00
Std
UC5115
165 305
0.25 0.60
1.50 5.00
Std
UTi20T
85 120
0.25 0.60
1.50 5.00
RK
MC5015
180 285
0.25 0.60
1.50 6.00
Flat
MC5015
180 285
0.20 0.60
2.50 6.00
GH
UC5115
160 290
0.25 0.60
1.50 6.00
Flat
UC5115
160 290
0.20 0.60
2.50 6.00
Flat
UTi20T
80 115
0.20 0.60
2.50 6.00
Flat
MC5015
180 285
0.20 0.60
2.50 6.00
Flat
UC5115
160 290
0.20 0.60
2.50 6.00
TURNING INSERTS
Work Material
A077
TURNING INSERTS
TURNING INSERTS
y NEGATIVE INSERTS
Work Material
Breker :
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Ductile Cast Iron

(FCD450)
Ductile Cast Iron

(FCD700)
< 450MPa
< 800MPa
LK
MC5005
220 355
0.10 0.40
0.30 2.00
MA
MC5005
210 335
0.20 0.50
0.30 4.00
MA
UC5105
160 295
0.20 0.50
0.30 4.00
MK
MC5005
210 335
0.20 0.55
1.00 4.00
GK
MC5005
210 335
0.25 0.60
1.50 5.00
Std
UC5105
160 295
0.25 0.60
1.50 5.00
Std
NX2525
145 200
0.25 0.60
1.50 5.00
RK
MC5005
195 315
0.25 0.60
1.50 6.00
Flat
MC5005
195 315
0.20 0.60
2.50 6.00
GH
UC5105
155 280
0.25 0.60
1.50 6.00
Flat
UC5105
155 280
0.20 0.60
2.50 6.00
Flat
HTi10
95 135
0.20 0.60
2.50 6.00
Flat
HTi05T
105 175
0.20 0.60
2.50 6.00
Flat
MC5005
195 315
0.20 0.60
2.50 6.00
Flat
UC5105
155 280
0.20 0.60
2.50 6.00
LK
MC5015
205 335
0.10 0.40
0.30 2.00
MA
MC5015
190 305
0.20 0.50
0.30 4.00
MA
UC5115
155 285
0.20 0.50
0.30 4.00
MP
UC5115
155 285
0.16 0.50
0.30 4.00
SW
UC5115
175 315
0.10 0.50
0.30 2.50
MK
MC5015
190 305
0.20 0.55
1.00 4.00
GK
MC5015
190 305
0.25 0.60
1.50 5.00
Std
UC5115
155 285
0.25 0.60
1.50 5.00
Std
HTi10
100 140
0.25 0.60
1.50 5.00
RK
MC5015
180 285
0.25 0.60
1.50 6.00
Flat
MC5015
180 285
0.20 0.60
2.50 6.00
GH
UC5115
150 275
0.25 0.60
1.50 6.00
Flat
UC5115
150 275
0.20 0.60
2.50 6.00
Flat
MC5015
180 285
0.20 0.60
2.50 6.00
Flat
UC5115
150 275
0.20 0.60
2.50 6.00
LK
MC5015
205 335
0.10 0.40
0.30 2.00
MA
MC5015
190 305
0.20 0.50
0.30 4.00
MA
UC5115
165 305
0.20 0.50
0.30 4.00
MK
MC5015
190 305
0.20 0.55
1.50 4.00
GK
MC5015
190 305
0.25 0.60
1.50 5.00
Std
UC5115
165 305
0.25 0.60
1.50 5.00
Std
UTi20T
85 120
0.25 0.60
1.50 5.00
RK
MC5015
180 285
0.25 0.60
1.50 6.00
Flat
MC5015
180 285
0.20 0.60
2.50 6.00
GH
UC5115
160 290
0.25 0.60
1.50 6.00
Flat
UC5115
160 290
0.20 0.60
2.50 6.00
Flat
UTi20T
80 115
0.20 0.60
2.50 6.00
Flat
MC5015
180 285
0.20 0.60
2.50 6.00
Flat
UC5115
160 290
0.20 0.60
2.50 6.00
LK
MC5005
195 315
0.10 0.40
0.30 2.00
MA
MC5005
210 335
0.20 0.50
0.30 4.00
MA
UC5105
160 295
0.20 0.50
0.30 4.00
: Stable Cutting
: General Cutting
: Unstable Cutting
A078
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Ductile Cast Iron

(FCD700)
< 800MPa
MK
MC5005
210 335
0.20 0.55
1.00 4.00
GK
MC5005
210 335
0.25 0.60
1.50 5.00
Std
UC5105
160 295
0.25 0.60
1.50 5.00
Std
NX2525
145 200
0.25 0.60
1.50 5.00
RK
MC5005
195 315
0.25 0.60
1.50 6.00
Flat
MC5005
195 315
0.20 0.60
2.50 6.00
GH
UC5105
155 280
0.25 0.60
1.50 6.00
Flat
UC5105
155 280
0.20 0.60
2.50 6.00
Flat
HTi10
95 135
0.20 0.60
2.50 6.00
Flat
HTi05T
105 175
0.20 0.60
2.50 6.00
Flat
MC5005
195 315
0.20 0.60
2.50 6.00
Flat
UC5105
155 280
0.20 0.60
2.50 6.00
LK
MC5015
205 335
0.10 0.40
0.30 2.00
MA
MC5015
190 305
0.20 0.50
0.30 4.00
MA
UC5115
155 285
0.20 0.50
0.30 4.00
MP
UC5115
155 285
0.16 0.50
0.30 4.00
SW
UC5115
175 315
0.10 0.50
0.30 2.50
MK
MC5015
190 305
0.20 0.55
1.00 4.00
GK
MC5015
190 305
0.25 0.60
1.50 5.00
Std
UC5115
155 285
0.25 0.60
1.50 5.00
Std
HTi10
100 140
0.25 0.60
1.50 5.00
RK
MC5015
180 285
0.25 0.60
1.50 6.00
Flat
MC5015
180 285
0.20 0.60
2.50 6.00
GH
UC5115
150 275
0.25 0.60
1.50 6.00
Flat
UC5115
150 275
0.20 0.60
2.50 6.00
Flat
MC5015
180 285
0.20 0.60
2.50 6.00
Flat
UC5115
150 275
0.20 0.60
2.50 6.00
LK
MC5015
205 335
0.10 0.40
0.30 2.00
MA
MC5015
190 305
0.20 0.50
0.30 4.00
MA
UC5115
165 305
0.20 0.50
0.30 4.00
MK
MC5015
190 305
0.20 0.55
1.00 4.00
GK
MC5015
190 305
0.25 0.60
1.50 5.00
Std
UC5115
165 305
0.25 0.60
1.50 5.00
Std
UTi20T
85 120
0.25 0.60
1.50 5.00
RK
MC5015
180 285
0.25 0.60
1.50 6.00
Flat
MC5015
180 285
0.20 0.60
2.50 6.00
GH
UC5115
160 290
0.25 0.60
1.50 6.00
Flat
UC5115
160 290
0.20 0.60
2.50 6.00
Flat
UTi20T
80 115
0.20 0.60
2.50 6.00
Flat
MC5015
180 285
0.20 0.60
2.50 6.00
Flat
UC5115
160 290
0.20 0.60
2.50 6.00
TURNING INSERTS
Work Material
A079
TURNING INSERTS
TURNING INSERTS
y NEGATIVE INSERTS
Work Material
Breker :
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Titanium Alloy
(Ti-6Al-4V)
FJ
RT9010
45 95
0.07 0.20
0.10 1.00
LS
MT9015
40 85
0.10 0.25
0.20 0.80
MJ(M)
RT9010
40 80
0.07 0.25
0.40 1.50
MS
MT9015
40 80
0.10 0.25
0.50 4.00
MS
RT9010
40 80
0.10 0.25
0.50 4.00
RS
MT9015
35 75
0.20 0.35
1.00 4.00
GJ
RT9010
35 75
0.16 0.35
1.00 3.00
FJ
RT9010
45 95
0.07 0.20
0.10 1.00
LS
MT9015
40 85
0.10 0.25
0.20 0.80
MJ(M)
RT9010
40 80
0.07 0.25
0.40 1.50
MJ(G)
RT9010
40 80
0.07 0.25
0.40 1.50
MS
MT9015
40 80
0.10 0.25
0.50 4.00
MS
RT9010
40 80
0.10 0.25
0.50 4.00
RS
MT9015
35 75
0.20 0.35
1.00 4.00
GJ
RT9010
35 75
0.16 0.35
1.00 3.00
FJ
RT9010
45 95
0.07 0.20
0.10 1.00
MJ(M)
RT9010
40 80
0.07 0.25
0.40 1.50
MJ(G)
RT9010
40 80
0.07 0.25
0.40 1.50
MS
RT9010
40 80
0.10 0.25
0.50 4.00
GJ
RT9010
35 75
0.16 0.35
1.00 3.00
FJ
VP10RT
30 60
0.07 0.20
0.10 1.00
LS
MP9005
30 110
0.10 0.25
0.20 0.80
MJ(M)
VP05RT
30 60
0.07 0.25
0.40 1.50
MJ(M)
US905
50 100
0.07 0.25
0.40 1.50
MJ(G)
VP10RT
25 50
0.07 0.25
0.40 1.50
MS
MP9005
30 100
0.10 0.25
0.50 4.00
MS
VP05RT
30 60
0.10 0.25
0.50 4.00
MS
US905
50 100
0.10 0.25
0.50 4.00
RS
MP9015
20 75
0.20 0.35
1.00 4.00
GJ
VP10RT
20 45
0.16 0.35
1.00 3.00
GJ
US905
45 95
0.16 0.35
1.00 3.00
FJ
VP10RT
30 60
0.07 0.20
0.10 1.00
LS
MP9015
25 85
0.10 0.25
0.20 0.80
MJ(M)
VP10RT
25 50
0.07 0.25
0.40 1.50
MS
MP9015
25 80
0.10 0.25
0.50 4.00
MS
VP10RT
25 50
0.10 0.25
0.50 4.00
RS
MP9015
20 75
0.20 0.35
1.00 4.00
GJ
VP10RT
20 45
0.16 0.35
1.00 3.00
FJ
VP15TF
20 40
0.07 0.20
0.10 1.00
MJ(M)
VP15TF
20 35
0.07 0.25
0.40 1.50

(Inconel718)
MJ(G)
VP15TF
20 35
0.07 0.25
0.40 1.50
MS
VP15TF
20 35
0.10 0.25
0.50 4.00
GJ
VP15TF
15 30
0.16 0.35
1.00 3.00
: Stable Cutting
: General Cutting
: Unstable Cutting
A080
Work Material
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Mild Steel

(AISI 1045, AISI 4140)
< 180HB
180
|
280HB
FP
NX2525
225 320
0.04 0.20
0.20 0.90
FV
NX2525
225 320
0.04 0.20
0.20 0.90
R/L-F
MP3025
230 350
0.05 0.12
0.10 0.50
LP
NX2525
225 320
0.06 0.25
0.20 1.00
Std
UE6110
205 350
0.08 0.30
0.30 2.00
MV
MP3025
190 295
0.08 0.30
0.30 2.00
Std
MP3025
190 295
0.08 0.30
0.30 2.00
MP
NX2525
185 265
0.08 0.30
0.30 2.00
FP
MC6015
250 425
0.04 0.20
0.20 0.90
FP
UE6110
250 425
0.04 0.20
0.20 0.90
FP
MP3025
230 350
0.04 0.20
0.20 0.90
FV
MP3025
230 350
0.04 0.20
0.20 0.90
FV
NX3035
215 305
0.04 0.20
0.20 0.90
LP
MC6015
250 425
0.06 0.25
0.20 1.00
LP
UE6110
250 425
0.06 0.25
0.20 1.00
LP
MP3025
230 350
0.06 0.25
0.20 1.00
Std
UE6110
205 350
0.08 0.30
0.30 2.00
MP
MC6015
205 350
0.08 0.30
0.30 2.00
MP
UE6110
205 350
0.08 0.30
0.30 2.00
MP
MP3025
190 295
0.08 0.30
0.30 2.00
FP
MC6025
250 405
0.04 0.20
0.20 0.90
FV
UE6020
235 385
0.04 0.20
0.20 0.90
LP
MC6025
250 405
0.06 0.25
0.20 1.00
Std
UE6020
195 320
0.08 0.30
0.30 2.00
MP
MC6025
205 335
0.08 0.30
0.30 2.00
FP
NX2525
165 235
0.04 0.20
0.20 0.90
FV
NX2525
165 235
0.04 0.20
0.20 0.90
R/L-F
MP3025
170 260
0.05 0.12
0.10 0.50
LP
NX2525
165 235
0.06 0.25
0.20 1.00
Std
UE6110
150 260
0.08 0.30
0.30 2.00
MV
MP3025
140 215
0.08 0.30
0.30 2.00
Std
MP3025
140 215
0.08 0.30
0.30 2.00
SV
MP3025
170 260
0.06 0.25
0.20 1.00
MW
MP3025
140 215
0.10 0.35
0.80 2.50
MP
NX2525
135 195
0.08 0.30
0.30 2.00
FP
MC6015
185 310
0.04 0.20
0.20 0.90
FP
UE6110
185 310
0.04 0.20
0.20 0.90
FP
MP3025
170 260
0.04 0.20
0.20 0.90
FV
MP3025
170 260
0.04 0.20
0.20 0.90
FV
NX3035
160 225
0.04 0.20
0.20 0.90
SW
MP3025
170 260
0.06 0.24
0.20 1.50
LP
MC6015
185 310
0.06 0.25
0.20 1.00
LP
UE6110
185 310
0.06 0.25
0.20 1.00
LP
MP3025
170 260
0.06 0.25
0.20 1.00
Std
UE6110
150 260
0.08 0.30
0.30 2.00
MP
MC6015
150 260
0.08 0.30
0.30 2.00
MP
UE6110
150 260
0.08 0.30
0.30 2.00
TURNING INSERTS
y 7 POSITIVE INSERT TYPE
A081
TURNING INSERTS
TURNING INSERTS
Work Material
Hardness
Breker :
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)

(AISI 1045, AISI 4140)

(AISI 4340)
180
|
280HB
280
|
350HB
MP
MP3025
140 215
0.08 0.30
0.30 2.00
FP
MC6025
185 295
0.04 0.20
0.20 0.90
FV
UE6020
175 285
0.04 0.20
0.20 0.90
LP
MC6025
185 295
0.06 0.25
0.20 1.00
Std
UE6020
145 235
0.08 0.30
0.30 2.00
MP
MC6025
150 245
0.08 0.30
0.30 2.00
MP
NX2525
95 140
0.08 0.30
0.30 2.00
MP
MC6015
110 185
0.08 0.30
0.30 2.00
MP
UE6110
110 185
0.08 0.30
0.30 2.00
MP
MP3025
100 155
0.08 0.30
0.30 2.00
MP
MC6025
110 175
0.08 0.30
0.30 2.00
: Stable Cutting
: General Cutting
: Unstable Cutting
A082
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Austenitic
Stainless Steel
Austenitic
Stainless Steel

(AISI 329)
< 200HB
>200HB
< 280HB
FM
VP15TF
75 125
0.04 0.20
0.20 0.90
Std
US735
70 135
0.08 0.30
0.30 2.00
LM
MC7025
140 190
0.06 0.25
0.20 1.00
Std
US735
70 135
0.08 0.30
0.30 2.00
MM
MC7025
115 155
0.08 0.30
0.30 2.00
FM
VP15TF
75 125
0.04 0.20
0.20 0.90
Std
US735
70 135
0.08 0.30
0.30 2.00
LM
MC7025
140 190
0.06 0.25
0.20 1.00
Std
US735
70 135
0.08 0.30
0.30 2.00
MM
MC7025
115 155
0.08 0.30
0.30 2.00
FM
VP15TF
75 125
0.04 0.20
0.20 0.90
Std
US735
70 135
0.08 0.30
0.30 2.00
LM
MP7035
85 135
0.06 0.25
0.20 1.00
LM
VP15TF
75 125
0.06 0.25
0.20 1.00
Std
US735
70 135
0.08 0.30
0.30 2.00
MM
MP7035
70 115
0.08 0.30
0.30 2.00
MM
VP15TF
60 105
0.08 0.30
0.30 2.00
FM
VP15TF
60 105
0.04 0.20
0.20 0.90
Std
US735
60 110
0.08 0.30
0.30 2.00
LM
MC7025
120 160
0.06 0.25
0.20 1.00
Std
US735
60 110
0.08 0.30
0.30 2.00
MM
MC7025
100 130
0.08 0.30
0.30 2.00
FM
VP15TF
60 105
0.04 0.20
0.20 0.90
Std
US735
60 110
0.08 0.30
0.30 2.00
LM
MC7025
120 160
0.06 0.25
0.20 1.00
Std
US735
60 110
0.08 0.30
0.30 2.00
MM
MC7025
100 130
0.08 0.30
0.30 2.00
FM
VP15TF
60 105
0.04 0.20
0.20 0.90
Std
US735
60 110
0.08 0.30
0.30 2.00
LM
MP7035
70 115
0.06 0.25
0.20 1.00
LM
VP15TF
60 105
0.06 0.25
0.20 1.00
Std
US735
60 110
0.08 0.30
0.30 2.00
MM
MP7035
60 95
0.08 0.30
0.30 2.00
MM
VP15TF
50 90
0.08 0.30
0.30 2.00
FM
VP15TF
50 85
0.04 0.20
0.20 0.90
Std
US735
45 90
0.08 0.30
0.30 2.00
LM
MC7025
95 130
0.06 0.25
0.20 1.00
Std
US735
45 90
0.08 0.30
0.30 2.00
MM
MC7025
80 105
0.08 0.30
0.30 2.00
FM
VP15TF
50 85
0.04 0.20
0.20 0.90
Std
US735
45 90
0.08 0.30
0.30 2.00
LM
MC7025
95 130
0.06 0.25
0.20 1.00
Std
US735
45 90
0.08 0.30
0.30 2.00
MM
MC7025
80 105
0.08 0.30
0.30 2.00
FM
VP15TF
50 85
0.04 0.20
0.20 0.90
Std
US735
45 90
0.08 0.30
0.30 2.00
LM
MP7035
55 95
0.06 0.25
0.20 1.00
TURNING INSERTS
Work Material
A083
TURNING INSERTS
TURNING INSERTS
Work Material
Hardness
Breker :
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)

(AISI 329)

Stainless Steel

Stainless Steel

< 280HB
< 200HB
>200HB
<450HB
LM
VP15TF
50 85
0.06 0.25
0.20 1.00
Std
US735
45 90
0.08 0.30
0.30 2.00
MM
MP7035
45 75
0.08 0.30
0.30 2.00
MM
VP15TF
40 70
0.08 0.30
0.30 2.00
FM
VP15TF
75 125
0.04 0.20
0.20 0.90
Std
US735
70 135
0.08 0.30
0.30 2.00
LM
MC7025
140 190
0.06 0.25
0.20 1.00
Std
US735
70 135
0.08 0.30
0.30 2.00
MM
MC7025
115 155
0.08 0.30
0.30 2.00
FM
VP15TF
75 125
0.04 0.20
0.20 0.90
Std
US735
70 135
0.08 0.30
0.30 2.00
LM
MC7025
140 190
0.06 0.25
0.20 1.00
Std
US735
70 135
0.08 0.30
0.30 2.00
MM
MC7025
115 155
0.08 0.30
0.30 2.00
FM
VP15TF
75 125
0.04 0.20
0.20 0.90
Std
US735
70 135
0.08 0.30
0.30 2.00
LM
MP7035
85 135
0.06 0.25
0.20 1.00
LM
VP15TF
75 125
0.06 0.25
0.20 1.00
Std
US735
70 135
0.08 0.30
0.30 2.00
MM
MP7035
70 115
0.08 0.30
0.30 2.00
MM
VP15TF
60 105
0.08 0.30
0.30 2.00
FM
VP15TF
60 105
0.04 0.20
0.20 0.90
Std
US735
60 110
0.08 0.30
0.30 2.00
LM
MC7025
120 160
0.06 0.25
0.20 1.00
Std
US735
60 110
0.08 0.30
0.30 2.00
MM
MC7025
100 130
0.08 0.30
0.30 2.00
FM
VP15TF
60 105
0.04 0.20
0.20 0.90
Std
US735
60 110
0.08 0.30
0.30 2.00
LM
MC7025
120 160
0.06 0.25
0.20 1.00
Std
US735
60 110
0.08 0.30
0.30 2.00
MM
MC7025
100 130
0.08 0.30
0.30 2.00
FM
VP15TF
60 105
0.04 0.20
0.20 0.90
Std
US735
60 110
0.08 0.30
0.30 2.00
LM
MP7035
70 115
0.06 0.25
0.20 1.00
LM
VP15TF
60 105
0.06 0.25
0.20 1.00
Std
US735
60 110
0.08 0.30
0.30 2.00
MM
MP7035
60 95
0.08 0.30
0.30 2.00
MM
VP15TF
50 90
0.08 0.30
0.30 2.00
FM
VP15TF
40 70
0.04 0.20
0.20 0.90
Std
US735
40 75
0.08 0.30
0.30 2.00
LM
MC7025
80 105
0.06 0.25
0.20 1.00
Std
US735
40 75
0.08 0.30
0.30 2.00
MM
MC7025
65 90
0.08 0.30
0.30 2.00
FM
VP15TF
40 70
0.04 0.20
0.20 0.90
Std
US735
40 75
0.08 0.30
0.30 2.00
LM
MC7025
80 105
0.06 0.25
0.20 1.00
Std
US735
40 75
0.08 0.30
0.30 2.00
: Stable Cutting
: General Cutting
: Unstable Cutting
A084
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)

<450HB
MM
MC7025
65 90
0.08 0.30
0.30 2.00
FM
VP15TF
40 70
0.04 0.20
0.20 0.90
Std
US735
40 75
0.08 0.30
0.30 2.00
LM
MP7035
45 75
0.06 0.25
0.20 1.00
LM
VP15TF
40 70
0.06 0.25
0.20 1.00
Std
US735
40 75
0.08 0.30
0.30 2.00
MM
MP7035
40 65
0.08 0.30
0.30 2.00
MM
VP15TF
35 60
0.08 0.30
0.30 2.00
TURNING INSERTS
Work Material
A085
TURNING INSERTS
TURNING INSERTS
Work Material
Hardness
Breker :
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Gray Cast Iron

(FC300)
Ductile Cast Iron

(FCD450)
Ductile Cast Iron

(FCD700)
< 350MPa
< 450MPa
< 800MPa
MK
MC5005
170 270
0.08 0.30
0.30 2.00
Std
UC5115
130 245
0.08 0.30
0.30 2.00
MK
MC5005
170 270
0.08 0.30
0.30 2.00
Std
UC5115
130 245
0.08 0.30
0.30 2.00
Flat
MC5005
170 270
0.08 0.30
0.30 2.00
Flat
UC5115
130 245
0.08 0.30
0.30 2.00
MK
MC5015
155 245
0.08 0.30
0.30 2.00
Std
UC5115
130 245
0.08 0.30
0.30 2.00
MK
MC5015
155 245
0.08 0.30
0.30 2.00
Std
UC5115
130 245
0.08 0.30
0.30 2.00
Flat
MC5015
155 245
0.08 0.30
0.30 2.00
Flat
UC5115
130 245
0.08 0.30
0.30 2.00
MK
MC5015
155 245
0.08 0.30
0.30 2.00
Std
UC5115
130 245
0.08 0.30
0.30 2.00
MK
MC5015
155 245
0.08 0.30
0.30 2.00
Std
UC5115
130 245
0.08 0.30
0.30 2.00
Flat
MC5015
155 245
0.08 0.30
0.30 2.00
Flat
UC5115
130 245
0.08 0.30
0.30 2.00
MK
MC5005
160 255
0.08 0.30
0.30 2.00
Std
UC5115
125 230
0.08 0.30
0.30 2.00
MK
MC5005
160 255
0.08 0.30
0.30 2.00
Std
UC5115
125 230
0.08 0.30
0.30 2.00
Flat
MC5005
160 255
0.08 0.30
0.30 2.00
Flat
UC5115
125 230
0.08 0.30
0.30 2.00
MK
MC5015
145 235
0.08 0.30
0.30 2.00
Std
UC5115
125 230
0.08 0.30
0.30 2.00
MK
MC5015
145 235
0.08 0.30
0.30 2.00
Std
UC5115
125 230
0.08 0.30
0.30 2.00
Flat
MC5015
145 235
0.08 0.30
0.30 2.00
Flat
UC5115
125 230
0.08 0.30
0.30 2.00
MK
MC5015
140 225
0.08 0.30
0.30 2.00
Std
UC5115
125 230
0.08 0.30
0.30 2.00
MK
MC5015
140 225
0.08 0.30
0.30 2.00
Std
UC5115
125 230
0.08 0.30
0.30 2.00
Flat
MC5015
140 225
0.08 0.30
0.30 2.00
Flat
UC5115
125 230
0.08 0.30
0.30 2.00
MK
MC5005
140 225
0.08 0.30
0.30 2.00
Std
UC5115
110 205
0.08 0.30
0.30 2.00
MK
MC5005
140 225
0.08 0.30
0.30 2.00
Std
UC5115
110 205
0.08 0.30
0.30 2.00
Flat
MC5005
140 225
0.08 0.30
0.30 2.00
Flat
UC5115
110 205
0.08 0.30
0.30 2.00
MK
MC5015
130 205
0.08 0.30
0.30 2.00
Std
UC5115
110 205
0.08 0.30
0.30 2.00
MK
MC5015
130 205
0.08 0.30
0.30 2.00
Std
UC5115
110 205
0.08 0.30
0.30 2.00
Flat
MC5015
130 205
0.08 0.30
0.30 2.00
: Stable Cutting
: General Cutting
: Unstable Cutting
A086
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Ductile Cast Iron

(FCD700)
< 800MPa
Flat
UC5115
110 205
0.08 0.30
0.30 2.00
MK
MC5015
130 205
0.08 0.30
0.30 2.00
Std
UC5115
110 205
0.08 0.30
0.30 2.00
MK
MC5015
130 205
0.08 0.30
0.30 2.00
Std
UC5115
110 205
0.08 0.30
0.30 2.00
Flat
MC5015
130 205
0.08 0.30
0.30 2.00
Flat
UC5115
110 205
0.08 0.30
0.30 2.00
TURNING INSERTS
Work Material
A087
TURNING INSERTS
TURNING INSERTS
Work Material
Hardness
Aluminium Alloy
(A6061, A7075)
Si<5%
Breker :
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Aluminium Alloy
(AC4B)
Aluminium Alloy
(ADC12, A390)
5% < Si < 10%
Si>10%
AZ
HTi10
300 700
0.10 0.40
0.20 3.00
AZ
HTi10
300 700
0.10 0.40
0.20 3.00
AZ
HTi10
300 700
0.10 0.40
0.20 3.00
AZ
HTi10
300 700
0.10 0.40
0.20 3.00
AZ
HTi10
300 700
0.10 0.40
0.20 3.00
AZ
HTi10
300 700
0.10 0.40
0.20 3.00
AZ
HTi10
300 700
0.10 0.40
0.20 3.00
AZ
HTi10
300 700
0.10 0.40
0.20 3.00
AZ
HTi10
300 700
0.10 0.40
0.20 3.00
: Stable Cutting
: General Cutting
: Unstable Cutting
A088
Hardness
Titanium Alloy
(Ti-6Al-4V)
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
FJ
RT9010
35 75
0.04 0.12
0.20 1.40
FJ
RT9010
35 75
0.04 0.12
0.20 1.40
FJ
RT9010
35 75
0.04 0.12
0.20 1.40
FJ
VP10RT
20 45
0.04 0.12
0.20 1.40
FJ
VP10RT
20 45
0.04 0.12
0.20 1.40
FJ
VP10RT
20 45
0.04 0.12
0.20 1.40
TURNING INSERTS
Work Material

(Inconel718)
A089
TURNING INSERTS
TURNING INSERTS
Work Material
Hardness
Breker :
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Mild Steel

(AISI 1045, AISI 4140)
< 180HB
180
|
280HB
R-R/L
NX2525
225 320
0.05 0.12
0.20 0.60
R-Std
NX2525
185 265
0.08 0.30
0.30 2.00
R-Std
NX2525
185 265
0.08 0.30
0.30 2.00
R-R/L
NX2525
225 320
0.05 0.12
0.20 0.60
R-Std
UE6110
205 350
0.08 0.30
0.30 2.00
R-Std
MP3025
190 295
0.08 0.30
0.30 2.00
R-Std
NX3035
180 255
0.08 0.30
0.30 2.00
R-Std
UE6110
205 350
0.08 0.30
0.30 2.00
R-Std
MP3025
190 295
0.08 0.30
0.30 2.00
R-Std
NX3035
180 255
0.08 0.30
0.30 2.00
R-R/L
UTi20T
115 165
0.05 0.12
0.20 0.60
R-Std
UE6020
195 320
0.08 0.30
0.30 2.00
N-Flat
UE6020
195 320
0.08 0.30
0.30 2.00
N-Flat
UP20M
105 160
0.08 0.30
0.30 2.00
R-Std
UE6020
195 320
0.08 0.30
0.30 2.00
N-Flat
UE6020
195 320
0.08 0.30
0.30 2.00
N-Flat
UP20M
105 160
0.08 0.30
0.30 2.00
R-R/L
NX2525
165 235
0.05 0.12
0.20 0.60
R-Std
NX2525
135 195
0.08 0.30
0.30 2.00
R-Std
NX2525
135 195
0.08 0.30
0.30 2.00
R-R/L
NX2525
165 235
0.05 0.12
0.20 0.60
R-Std
UE6110
150 260
0.08 0.30
0.30 2.00
R-Std
MP3025
140 215
0.08 0.30
0.30 2.00
R-Std
NX3035
130 190
0.08 0.30
0.30 2.00
R-Std
UE6110
150 260
0.08 0.30
0.30 2.00
R-Std
MP3025
140 215
0.08 0.30
0.30 2.00
R-Std
NX3035
130 190
0.08 0.30
0.30 2.00
R-R/L
UTi20T
85 120
0.05 0.12
0.20 0.60
R-Std
UE6020
145 235
0.08 0.30
0.30 2.00
N-Flat
UE6020
145 235
0.08 0.30
0.30 2.00
N-Flat
UP20M
75 115
0.08 0.30
0.30 2.00
R-Std
UE6020
145 235
0.08 0.30
0.30 2.00
N-Flat
UE6020
145 235
0.08 0.30
0.30 2.00
N-Flat
UP20M
75 115
0.08 0.30
0.30 2.00
: Stable Cutting
: General Cutting
: Unstable Cutting
A090
Hardness
Cutting
Mode
Priority Breaker
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Gray Cast Iron

(FC300)
Ductile Cast Iron

(FCD450)
Ductile Cast Iron

(FCD700)
< 350MPa
< 450MPa
< 800MPa
R-R/L
NX2525
150 205
0.05 0.12
0.20 0.60
N-Flat
UC5105
135 250
0.08 0.30
0.30 2.00
N-Flat
NX2525
125 170
0.08 0.30
0.30 2.00
R-Std
NX2525
125 170
0.08 0.30
0.30 2.00
N-Flat
UC5105
135 250
0.08 0.30
0.30 2.00
N-Flat
NX2525
125 170
0.08 0.30
0.30 2.00
R-Std
NX2525
125 170
0.08 0.30
0.30 2.00
R-R/L
NX2525
150 205
0.05 0.12
0.20 0.60
R-R/L
HTi10
100 145
0.05 0.12
0.20 0.60
N-Flat
UC5115
130 245
0.08 0.30
0.30 2.00
N-Flat
UE6110
130 200
0.08 0.30
0.30 2.00
N-Flat
UC5115
130 245
0.08 0.30
0.30 2.00
N-Flat
UE6110
130 200
0.08 0.30
0.30 2.00
R-R/L
UTi20T
80 115
0.05 0.12
0.20 0.60
N-Flat
VP15TF
115 160
0.08 0.30
0.30 2.00
N-Flat
VP15TF
115 160
0.08 0.30
0.30 2.00
R-R/L
NX2525
140 190
0.05 0.12
0.20 0.60
N-Flat
UC5105
130 235
0.08 0.30
0.30 2.00
N-Flat
NX2525
115 160
0.08 0.30
0.30 2.00
R-Std
NX2525
115 160
0.08 0.30
0.30 2.00
N-Flat
UC5105
130 235
0.08 0.30
0.30 2.00
N-Flat
NX2525
115 160
0.08 0.30
0.30 2.00
R-Std
NX2525
115 160
0.08 0.30
0.30 2.00
R-R/L
NX2525
140 190
0.05 0.12
0.20 0.60
R-R/L
HTi10
95 135
0.05 0.12
0.20 0.60
N-Flat
UC5115
125 230
0.08 0.30
0.30 2.00
N-Flat
UE6110
120 190
0.08 0.30
0.30 2.00
N-Flat
UC5115
125 230
0.08 0.30
0.30 2.00
N-Flat
UE6110
120 190
0.08 0.30
0.30 2.00
R-R/L
UTi20T
75 110
0.05 0.12
0.20 0.60
N-Flat
VP15TF
110 150
0.08 0.30
0.30 2.00
N-Flat
VP15TF
110 150
0.08 0.30
0.30 2.00
R-R/L
NX2525
125 170
0.05 0.12
0.20 0.60
N-Flat
UC5105
115 210
0.08 0.30
0.30 2.00
N-Flat
NX2525
105 140
0.08 0.30
0.30 2.00
R-Std
NX2525
105 140
0.08 0.30
0.30 2.00
N-Flat
UC5105
115 210
0.08 0.30
0.30 2.00
N-Flat
NX2525
105 140
0.08 0.30
0.30 2.00
R-Std
NX2525
105 140
0.08 0.30
0.30 2.00
R-R/L
NX2525
125 170
0.05 0.12
0.20 0.60
R-R/L
HTi10
85 120
0.05 0.12
0.20 0.60
N-Flat
UC5115
110 205
0.08 0.30
0.30 2.00
N-Flat
UE6110
105 170
0.08 0.30
0.30 2.00
N-Flat
UC5115
110 205
0.08 0.30
0.30 2.00
N-Flat
UE6110
105 170
0.08 0.30
0.30 2.00
R-R/L
UTi20T
65 95
0.05 0.12
0.20 0.60
N-Flat
VP15TF
95 135
0.08 0.30
0.30 2.00
N-Flat
VP15TF
95 135
0.08 0.30
0.30 2.00
TURNING INSERTS
Work Material
A091
TYPE INSERTS
WITH HOLE

7
6
FY
4
3
SY
2
1
0
0.1
WITH
HOLE
0.3
0.5
Light Cutting
Feed (mm/rev)
0.7
HX
6
5
FH
LP
4
3
RP
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
6
5
4
3
2
MW
1
0
0.7
SW
0.1
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
Rough Cutting

8
MM
RM
5
4
3
2
1
0
Heavy Cutting
P
M
K
N
S
Medium Cutting
LM
0.1
0.3
0.5
Feed (mm/rev)
: Stable Cutting
Flat Top
5
4
3
LK
2
1
0
0.7
RK
MK
0.1
: General Cutting
0.3
: Unstable Cutting
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
RE
(mm)
Carbide
Shape
Order Number
FH
CNMG120402-FH
CNMG120404-FH
CNMG120408-FH
CNMG120412-FH
0.2
0.4
a [
a a a
a [
a a
0.8
a a
CNMG120404-FS
CNMG120408-FS
0.4
0.8
CNMG120404-FY
CNMG120408-FY
0.4
0.8
a a
CNGG1204V5-FJ
CNGG120401-FJ
CNGG120402-FJ
CNGG120404-FJ
CNGG120408-FJ
CNGG120404-PK
0.05
0.1
0.2
0.4
0.8
a a
CNMG120404-LP
CNMG120408-LP
CNMG120412-LP
0.4
0.8
a a
a a
a a
a a
1.2
a a
a a
CNMG120404-LM
CNMG120408-LM
CNMG120412-LM
0.4
0.8
a a a
1.2
a a a
1.2
C008
C009
E013
E036
E040
H006
008
Finish Cutting
a
C008
C009
E013
E036
E040
H006
008
Finish Cutting
FY
C008
C009
E013
E036
E040
H006
008
Finish Cutting
FJ
Finish Cutting
PK
a a
0.4
a
a
Light Cutting
LM
a a a
Light Cutting
A092
a : Inventory maintained in Japan.

C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
Finish Cutting
LP
0.7
Steel
Coated
FS
0.5
Feed (mm/rev)
Applicable
Holder Page
Depth of Cut (mm)

Size
Mild Steel
8
Depth of Cut (mm)
Finish Cutting
CNMG 12 04 02- FH
Depth of Cut (mm)
CN
Depth of Cut (mm)
NEG
80
Depth of Cut (mm)
TURNING INSERTS
: Inventory maintained in Japan. To be replaced by new products.
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
RE
(mm)
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Shape
Order Number
LK
CNMG120404-LK
CNMG120408-LK
CNMG120412-LK
0.4
0.8
a a
1.2
a a
CNMG120404-LS
CNMG120408-LS
0.4
0.8
CNMG09T304-SH
CNMG09T308-SH
CNMG120404-SH
CNMG120408-SH
CNMG120412-SH
CNMG120404-SA
CNMG120408-SA
CNMG120412-SA
0.4
0.8
NEW
: Unstable Cutting
C008
C009
E013
E036
E040
H006
008
a a
Light Cutting
NEW
LS
a a
a a
Light Cutting
SH
Light Cutting
SA
SW
0.4
a a [ a a
a a
0.8
1.2
a a [ a a
a a
0.4
0.8
a a [ a a
a a [ a a
1.2
a a [ a a
CNMG120404-SW
CNMG120408-SW
CNMG120412-SW
0.4
0.8
a a
a a
a a a
a a
a a
a a a
1.2
a a
CNMG120404-SY
CNMG120408-SY
0.4
0.8
CNMG120404-C
CNMG120408-C
0.4
0.8
CNMG120404-MJ
CNMG120408-MJ
CNMG120412-MJ
CNMG120416-MJ
0.4
0.8
a a
a a
1.2
a a
1.6
a a
CNGG120404-MJ
CNGG120408-MJ
0.4
0.8
a a [ a a
a a a
C008
C009
E013
E036
E040
H006
008
[[
C008
C009
E013
E036
E040
H006
008
[[
Light Cutting
MJ
C008
C009
E013
E036
E040
H006
008
Light Cutting
MJ
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
Light Cutting
WITH
HOLE
C008
C009
E013
E036
E040
H006
008
Light Cutting
(Wiper)
SY
NEG
C008
C009
E013
E036
E040
H006
008
Light Cutting
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
a a
a a
a a
a a
C008
C009
E013
E036
E040
H006
008
Light Cutting
=
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A093
TYPE INSERTS
WITH HOLE

7
6
FY
4
3
SY
2
1
0
0.1
WITH
HOLE
0.3
0.5
Light Cutting
Medium Cutting
Feed (mm/rev)
0.7
HX
6
5
FH
LP
4
3
RP
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
5
4
3
SW
MW
1
0
0.7
0.1
0.3
0.5
Feed (mm/rev)
Work
Material
MM
RM
5
4
3
2
1
0.3
0.5
Feed (mm/rev)
Coated
Cermet Cermet
a a [ a a
1.2
a a [ a a
1.6
a a [ a a
0.8
a a [
1.2
1.6
a a [
a a [
MK
0.1
0.3
0.5
Feed (mm/rev)
0.7
: Unstable Cutting
CNMG120404-GM
CNMG120408-GM
CNMG120412-GM
0.4
0.8
a a a
1.2
a a a
a a a
1.6
a a a
0.8
a a a
1.2
a a a
1.6
a a a
0.8
a a a
1.2
1.6
a a a
C008
C009
E013
E036
E040
H006
008
a a a
0.4
0.8
a a
1.2
a a
1.6
a a
1.2
a a
1.6
a a
1.2
1.6
a a
0.4
0.8
a a
1.2
a a
C008
C009
E013
E036
E040
H006
008
a a a
a a
C008
C009
E013
E036
E040
H006
008
a a
a a
a a a
Medium Cutting

Carbide
0.8
1.2
Medium Cutting
A094
LK
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
RE
(mm)
GM
GK
Non-ferrous Metal
a a [ a a
NEW
Cast Iron
0.4
0.8
Medium Cutting
Flat Top
Stainless Steel
CNMG120404-MP
CNMG120408-MP
CNMG120412-MP
CNMG120416-MP
CNMG160608-MP
CNMG160612-MP
CNMG160616-MP
CNMG120408-MM
CNMG120412-MM
CNMG120416-MM
CNMG160608-MM
CNMG160612-MM
CNMG160616-MM
CNMG190608-MM
CNMG190612-MM
CNMG190616-MM
CNMG120404-MK
CNMG120408-MK
CNMG120412-MK
CNMG120416-MK
CNMG160612-MK
CNMG160616-MK
CNMG190612-MK
CNMG190616-MK
CNMG120404-GK
CNMG120408-GK
CNMG120412-GK
MK
RK
Steel
MP
NEW
: General Cutting
Order Number
Medium Cutting
0.7
Shape
MM
LM
0.1
: Stable Cutting
Coated
Medium Cutting
Heavy Cutting
0.7
P
M
K
N
S
8
6
Rough Cutting
Applicable
Holder Page
Depth of Cut (mm)

Size
Mild Steel
8
Depth of Cut (mm)
Finish Cutting
CNMG 12 04 04- MP
Depth of Cut (mm)
CN
Depth of Cut (mm)
NEG
80
Depth of Cut (mm)
TURNING INSERTS
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Shape
Order Number
MA
CNMG120404-MA
CNMG120408-MA
CNMG120412-MA
CNMG120416-MA
CNMG160608-MA
CNMG160612-MA
CNMG160616-MA
CNMG190612-MA
CNMG190616-MA
CNMG120404-MH
CNMG120408-MH
CNMG120412-MH
CNMG120416-MH
CNMG160608-MH
CNMG160612-MH
CNMG160616-MH
CNMG190612-MH
CNMG190616-MH
CNMG090308
CNMG09T304
CNMG09T308
CNMG120404
CNMG120408
CNMG120412
CNMG120416
CNMG160608
CNMG160612
CNMG160616
CNMG190608
CNMG190612
CNMG190616
CNMG120408-MW
CNMG120412-MW
0.4
0.8
a a [ a a
a a [ a
a a a a
a a [ a a a
a a [ a
a a a a
1.2
a a [ a a a
a a [ a
a a a a
1.6
a a [
[ a
0.8
a a [
1.2
a a [
[ a
1.6
a a
1.2
1.6
a a [
[ a
a a
0.4
0.8
a a [
CNMG090304-MS
CNMG090308-MS
CNMG09T304-MS
CNMG09T308-MS
CNMG120404-MS
CNMG120408-MS
CNMG120412-MS
0.4
0.8
MH
Medium Cutting
Standard
Medium Cutting
RE
(mm)
1 MW
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Medium Cutting
: Unstable Cutting
a [
a
a a [ a a a
1.2
a a [ a a a
1.6
a a [
0.8
a a
1.2
a a [
1.6
a a
1.2
1.6
a a [
0.8
0.4
0.8
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
a
a
a
a
a a [
a
a
0.4
a a [ a a a
a a
0.8
a a [ a a a
a a
1.2
a a [ a a a
a a
1.6
a a
a a
0.8
a a [
1.2
a a [
a a
1.6
a a
a a
0.8
a a [
a a
1.2
1.6
a a [
a a
a a [
a a
0.8
1.2
a a [ a a
a a a a
a a [ a a
a a a a
a a a
C008
C009
E013
E036
E040
H006
008
a a
a
C008
C009
E013
E036
E040
H006
008
Medium Cutting
(Wiper)
*2 MS
Medium Cutting
NEG
WITH
HOLE
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
a
a
0.4
a
a
0.8
0.4
a [
[ a a
a a a a a a
0.8
1.2
a [
[ a a
a a a a a a
[ a a
a a a a a
a
a a a
a
a a a
C008
C009
E013
E036
E040
H006
008
a a
refer to A028 before using the MW breaker (wiper insert).

*12 Please
Newly designed breakers : MP9005, MP9015, MT9015
*
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A095
TYPE INSERTS
WITH HOLE

7
6
FY
4
3
SY
2
1
0
0.1
WITH
HOLE
0.3
0.5
Light Cutting
Feed (mm/rev)
0.7
HX
6
5
FH
LP
4
3
RP
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
6
5
4
3
2
MW
1
0
0.7
SW
0.1
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
MM
RM
5
4
3
2
1
0
LM
0.1
RM
Rough Cutting
NEW
RK
Rough Cutting
NEW
RS
Rough Cutting
0.5
Feed (mm/rev)
: Stable Cutting
0.7
Flat Top
5
4
3
LK
2
1
0
MK
0.1
: General Cutting
0.3
0.5
Feed (mm/rev)
0.7
: Unstable Cutting

Coated
Cermet Cermet

Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
RE
(mm)
0.8
1.2
a
a
1.6
1.2
1.6
a a
a a
a
a
0.8
1.2
a a
a a
a a
a a
1.6
a a
a a
1.2
a a
a a
1.6
a a
a a
1.2
1.6
a a
a a
a a
a a
0.8
1.2
a a a
1.6
a a a
1.2
a a a
1.6
a a a
1.2
1.6
a a a
a a a
C008
C009
E013
E036
E040
H006
008
a a a
0.8
1.2
a a
1.6
a a
1.2
a a
1.6
a a
1.2
1.6
a a
a a
C008
C009
E013
E036
E040
H006
008
a a
0.8
1.2
1.6
1.2
1.6
1.2
1.6
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
* Newly designed breakers : MP9005, MP9015, MT9015
A096
RK
Non-ferrous Metal
CNMG160608-MS
CNMG160612-MS
CNMG160616-MS
CNMG190612-MS
CNMG190616-MS
CNMG120408-RP
CNMG120412-RP
CNMG120416-RP
CNMG160612-RP
CNMG160616-RP
CNMG190612-RP
CNMG190616-RP
CNMG120408-RM
CNMG120412-RM
CNMG120416-RM
CNMG160612-RM
CNMG160616-RM
CNMG190612-RM
CNMG190616-RM
CNMG120408-RK
CNMG120412-RK
CNMG120416-RK
CNMG160612-RK
CNMG160616-RK
CNMG190612-RK
CNMG190616-RK
CNMG120408-RS
CNMG120412-RS
CNMG120416-RS
CNMG160612-RS
CNMG160616-RS
CNMG190612-RS
CNMG190616-RS
Rough Cutting
0.3
Cast Iron
MS
RP
Stainless Steel
Order Number
Medium Cutting
Steel
Shape
NEW
Heavy Cutting
Coated
Rough Cutting
P
M
K
N
S
Medium Cutting
Applicable
Holder Page
Depth of Cut (mm)

Size
Mild Steel
8
Depth of Cut (mm)
Finish Cutting
CNMG 16 06 08- MS
Depth of Cut (mm)
CN
Depth of Cut (mm)
NEG
80
Depth of Cut (mm)
TURNING INSERTS
C008
C009
E013
E036
E040
H006
008
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Order Number
GH
CNMG120408-GH
CNMG120412-GH
CNMG120416-GH
CNMG160612-GH
CNMG160616-GH
CNMG190612-GH
CNMG190616-GH
CNMG120408-GJ
CNMG120412-GJ
CNMG120416-GJ
CNMG160612-GJ
CNMG190612-GJ
CNMG190616-GJ
CNMM120408-HZ
CNMM120412-HZ
CNMM160612-HZ
CNMM160616-HZ
CNMM190612-HZ
CNMM190616-HZ
CNMM190612-HX
CNMM190616-HX
CNMM190624-HX
CNMM250924-HX
0.8
1.2
a a [
[ a
a a [
[ a
1.6
a a
1.2
a a [
1.6
a a
1.2
1.6
a a [
a a
a a [
[ a
a a
Rough Cutting
HZ
Heavy Cutting
HX
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
RE
(mm)
Shape
GJ
: Unstable Cutting
Steel
Coated
Rough Cutting
: General Cutting
Applicable
Holder Page
Work
Material
P
M
K
N
S
: Stable Cutting
TURNING INSERTS
WITH
HOLE
a a
a a
C008
C009
E013
E036
E040
H006
008
a a
[ a
NEG
a a
a a
0.8
1.2
a a
a a
1.6
a a
1.2
1.2
1.6
0.8
1.2
a [
1.2
a [
1.6
a [
1.2
1.6
a [
a [
1.2
1.6
a [
a [
2.4
a [
2.4
a [
CNMM190616-HV
CNMM190624-HV
CNMM250924-HV
1.6
2.4
a [
a [
2.4
a [
CNMA120404
CNMA120408
CNMA120412
CNMA120416
CNMA160612
CNMA160616
CNMA190612
CNMA190616
0.4
0.8
a a a a
a a
a a a a
a a
1.2
a a a a
1.6
a a a a
1.2
a a a a
1.6
a a a a
1.2
1.6
a a a a
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
a [
C008
C009
Heavy Cutting
HV
C008
C009
Heavy Cutting
Flat Top
C008
C009
E013
E036
E040
H006
008
a a a a
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A097
TYPE INSERTS
WITH HOLE
Light Cutting
Medium Cutting
Mild Steel
FY
4
3
SY
2
1
0
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
FH
LP
4
3
RP
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
6
5
4
3
2
MW
1
0
0.7
SW
0.1
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
P
M
K
N
S
Depth of Cut (mm)
Depth of Cut (mm)
8
6
Rough Cutting
8
6

Size
MM
RM
5
4
3
2
1
LM
0.1
0.3
0.5
Feed (mm/rev)
: Stable Cutting
RK
Flat Top
6
5
4
3
LK
2
1
0
0.7
MK
0.1
: General Cutting
0.3
: Unstable Cutting
Non-ferrous Metal
Coated
Cermet Cermet
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
RE
(mm)
FH
DNMG150402-FH
DNMG150404-FH
DNMG150408-FH
DNMG150602-FH
DNMG150604-FH
DNMG150608-FH
DNMG150404-FS
DNMG150408-FS
0.2
0.4
a [
a a a
a a a a
0.8
0.2
a [
a a a
0.4
0.8
a [
a [
DNMG150404-FY
DNMG150408-FY
DNMG150604-FY
DNMG150608-FY
0.4
0.8
DNGG150404-FJ
DNGG150408-FJ
0.4
0.8
DNGG150404-PK
0.4
DNMG110404-LP
DNMG110408-LP
DNMG150404-LP
DNMG150408-LP
DNMG150412-LP
DNMG150604-LP
DNMG150608-LP
DNMG150612-LP
0.4
0.8
a a
a a
a a
a a
0.4
a a
a a
0.8
a a
a a
1.2
a a
a a
0.4
a a
a a
0.8
1.2
a a
a a
a a
a a
0.4
0.8
C010
C011
E013
E036
040
H009
011
a a
a
[
C010
C011
E013
E036
040
H009
011
Finish Cutting
[
a a
0.4
C010
C011
E013
E036
040
H009
011
0.8
Finish Cutting
FJ
a a
a a
Finish Cutting
PK
Light Cutting
A098

C010
C011
E013
E036
040
H009
011
C010
C011
E013
E036
040
H009
011
Finish Cutting
LP
0.7
Cast Iron
Order Number
FY
0.5
Feed (mm/rev)
Stainless Steel
Shape
FS
Steel
Coated
Finish Cutting
K
8
Heavy Cutting
Applicable
Holder Page
Finish Cutting
DNMG 15 04 02- FH
Depth of Cut (mm)
DN
Depth of Cut (mm)
NEG
55
Depth of Cut (mm)
TURNING INSERTS
C010
C011
E013
E036
040
H009
011
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
RE
(mm)
Shape
Order Number
LM
DNMG110404-LM
DNMG110408-LM
DNMG150404-LM
DNMG150408-LM
DNMG150412-LM
DNMG150604-LM
DNMG150608-LM
DNMG150612-LM
DNMG150404-LK
DNMG150408-LK
DNMG150412-LK
DNMG150604-LK
DNMG150608-LK
DNMG150612-LK
DNMG150404-LS
DNMG150408-LS
DNMG150604-LS
DNMG150608-LS
0.4
0.8
a a a
0.4
a a a
0.8
a a a
1.2
a a a
0.4
a a a
0.8
1.2
a a a
DNMG110404-SH
DNMG110408-SH
DNMG150404-SH
DNMG150408-SH
DNMG150412-SH
DNMG150604-SH
DNMG150608-SH
DNMG150612-SH
DNMG150404-SA
DNMG150408-SA
DNMG150412-SA
DNMG150604-SA
DNMG150608-SA
DNMG150612-SA
DNMX110404-SW
DNMX110408-SW
DNMX150404-SW
DNMX150408-SW
DNMX150412-SW
DNMX150604-SW
DNMX150608-SW
DNMX150612-SW
DNMG150404-SY
DNMG150408-SY
DNMG150604-SY
DNMG150608-SY
0.4
0.8
a a
a a
0.4
a a [ a a
a a
0.8
a a [ a a
a a
1.2
a a [ a a
0.4
a a
0.8
1.2
a a
a a
0.4
0.8
a a [ a a
a a [ a a
1.2
a a [ a a
0.4
a a [
0.8
1.2
a a [
a a [
0.4
0.8
0.4
a a
a a a
0.8
a a
a a a
1.2
a a
a a
0.4
a a
a a a
0.8
1.2
a a
a a a
a a
a a
Light Cutting
LK
Light Cutting
NEW
LS
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
NEW
: Unstable Cutting
Light Cutting
SA
Light Cutting
SW
Light Cutting
(Wiper)
a a a
C010
C011
E013
E036
040
H009
011
a a a
0.4
0.8
a a
1.2
a a
0.4
a a
0.8
1.2
a a
C010
C011
E013
E036
040
H009
011
a a
a a
0.4
0.8
a a
a a
0.4
a a
0.8
a a
SY
0.4
0.8
C010
C011
E013
E036
040
H009
011
C010
C011
E013
E036
040
H009
011
C010
C011
E013
E036
040
H009
011
a a
0.4
0.8
NEG
WITH
HOLE
Light Cutting
SH
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
C010
E013
E036
E038
E039
H009
H 011
C010
C011
E013
E036
040
H009
011
a
[
Light Cutting
=
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A099
TYPE INSERTS
WITH HOLE
Light Cutting
Medium Cutting
Mild Steel
FY
4
3
SY
2
1
0
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
FH
LP
4
3
RP
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
0.7
6
5
4
3
SW
MW
1
0
0.1
0.3
0.5
Feed (mm/rev)
Depth of Cut (mm)
Depth of Cut (mm)
8
6
Work
Material
P
M
K
N
S
MM
RM
5
4
3
2
1
0.3
0.5
Feed (mm/rev)

7
Flat Top
5
4
3
LK
2
1
0
0.7
RK
MK
0.1
: General Cutting
0.3
Light Cutting
MJ
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
RE
(mm)
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Order Number
DNMG150404-C
DNMG150408-C
DNMG150604-C
DNMG150608-C
0.4
0.8
[[
0.4
[[
0.8
[[
DNMG150404-MJ
DNMG150408-MJ
DNMG150412-MJ
DNMG150416-MJ
DNMG150604-MJ
DNMG150608-MJ
DNMG150612-MJ
DNMG150616-MJ
DNGM150404-MJ
DNGM150408-MJ
0.4
0.8
a a
a a
1.2
a a
1.6
a a
0.4
a a
0.8
a a
1.2
1.6
a a
a a
DNMG150404-MP
DNMG150408-MP
DNMG150412-MP
DNMG150416-MP
DNMG150604-MP
DNMG150608-MP
DNMG150612-MP
DNMG150616-MP
DNMG150408-MM
DNMG150412-MM
DNMG150608-MM
DNMG150612-MM
0.4
0.8
a a [ a a
a a [ a a
1.2
a a [ a a
1.6
a a [ a a
0.4
a a [ a a
0.8
a a [ a a
1.2
1.6
a a [ a a
a a [ a a
DNMG150404-MK
DNMG150408-MK
DNMG150412-MK
DNMG150604-MK
DNMG150608-MK
DNMG150612-MK
0.4
0.8
a a
1.2
a a
0.4
a a
0.8
1.2
a a
C010
C011
E013
E036
040
H009
011
[[
0.4
0.8
C010
C011
E013
E036
040
H009
011
a a
a a
a a
a a
Light Cutting
MP
Medium Cutting
MM
0.8
1.2
a a a
0.8
a a a
1.2
a a a
MK
Medium Cutting
A100

C010
C011
E013
E036
040
H009
011
C010
C011
E013
E036
040
H009
011
C010
C011
E013
E036
040
H009
011
a a a
Medium Cutting
NEW
0.7
: Unstable Cutting
Light Cutting
MJ
0.5
Feed (mm/rev)
Steel
Coated
Shape
LM
0.1
: Stable Cutting
Heavy Cutting
0.7
Rough Cutting
8
6

Size
Applicable
Holder Page
Finish Cutting
DNMG 15 04 04- C
Depth of Cut (mm)
DN
Depth of Cut (mm)
NEG
55
Depth of Cut (mm)
TURNING INSERTS
a a
a a
C010
C011
E013
E036
040
H009
011
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Shape
Order Number
GK
DNMG150404-GK
DNMG150408-GK
DNMG150412-GK
DNMG150604-GK
DNMG150608-GK
DNMG150612-GK
DNMG150404-GM
DNMG150408-GM
DNMG150412-GM
DNMG150604-GM
DNMG150608-GM
DNMG150612-GM
DNMG110404-MA
DNMG110408-MA
DNMG110412-MA
DNMG150404-MA
DNMG150408-MA
DNMG150412-MA
DNMG150604-MA
DNMG150608-MA
DNMG150612-MA
DNMG150616-MA
DNMG150404-MH
DNMG150408-MH
DNMG150412-MH
DNMG150604-MH
DNMG150608-MH
DNMG150612-MH
DNMG110408
DNMG150404
DNMG150408
DNMG150412
DNMG150416
DNMG150604
DNMG150608
DNMG150612
DNMG150616
DNMX150408-MW
DNMX150412-MW
DNMX150608-MW
DNMX150612-MW
Medium Cutting
GM
Medium Cutting
MA
Medium Cutting
MH
Medium Cutting
Standard
Medium Cutting
MW
Medium Cutting
(Wiper)
RE
(mm)
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
NEW
: Unstable Cutting
0.4
0.8
a a
1.2
a a
0.4
a a
0.8
1.2
a a
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
NEG
WITH
HOLE
C010
C011
E013
E036
040
H009
011
a a
a a
0.4
0.8
a a a
1.2
a a a
0.4
a a a
0.8
1.2
a a a
C010
C011
E013
E036
040
H009
011
a a a
a a a
0.4
0.8
a a
1.2
a a
0.4
a a [ a a
a a [ a
a a a a
0.8
a a [ a a a
a a [ a
a a a a
1.2
a a [ a a a
a a
a a
0.4
a a [ a a
a a [ a
a a
0.8
a a [ a a a
a a [ a
a a a a
1.2
1.6
a a [ a a
a a [ a
a a a a
0.4
0.8
a a [
a a [ a a a
1.2
a a [ a a
0.4
a a
0.8
1.2
a a [ a a
a a
C010
C011
E013
E036
040
H009
011
C010
C011
E013
E036
040
H009
011
a
[
a a [ a a
0.8
0.4
a a [ a a
a a
a a a
0.8
a a [ a a
a a
a a a
1.2
a a [ a a
a a
1.6
0.4
a a [
a a
0.8
a a [ a a
a a
1.2
1.6
a a [ a a
a a
0.8
1.2
a a
a a a a
a a
a a a a
0.8
a a
1.2
a a
C010
C011
E013
E036
040
H009
011
C010
E013
E036
E038
E039
H009
H011
a a a a
a a
* Please refer to A028 before using the MW breaker (wiper insert).
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A101
TYPE INSERTS
WITH HOLE
Light Cutting
Medium Cutting
Mild Steel
FY
4
3
SY
2
1
0
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
FH
LP
4
3
RP
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
6
5
4
3
2
MW
1
0
0.7
SW
0.1
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
P
M
K
N
S
Depth of Cut (mm)
Depth of Cut (mm)
8
6
Rough Cutting
8
6
MM
RM
5
4
3
2
1
0
LM
0.1
0.3
0.5
Feed (mm/rev)
: Stable Cutting
Rough Cutting
RM
Rough Cutting
NEW
RK
RK
Flat Top
6
5
4
3
LK
2
1
0
MK
0.1
0.3
: General Cutting
0.7
: Unstable Cutting

Coated
Cermet Cermet
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
RE
(mm)
Carbide
0.8
0.4
a
a [
[ a a
a a a a a
0.8
[ a a
a a a a a a
1.2
a a
a a a a
0.4
[ a a
a a a a
0.8
1.2
[ a a
a a a a
a a a a
a
a
a a
a
a
a
a
a a
a a
0.8
a a
0.8
a a
0.4
0.4
0.8
0.8
C010
C011
E013
E036
040
H009
011
0.8
1.2
a a
a a
a a
a a
1.6
a a
a a
0.8
a a
a a
1.2
1.6
a a
a a
a a
a a
C010
C011
E013
E036
040
H009
011
0.8
1.2
a a a
1.6
a a a
0.8
a a a
1.2
1.6
a a a
C010
C011
E013
E036
040
H009
011
a a a
a a a
0.8
1.2
a a
0.8
a a
1.2
a a
C010
C011
E013
E036
040
H009
011
a a

C010
C011
E013
E036
040
H009
011
0.4
0.4
Rough Cutting
A102
0.5
Feed (mm/rev)
Non-ferrous Metal
DNMG110408-MS
DNMG150404-MS
DNMG150408-MS
DNMG150412-MS
DNMG150604-MS
DNMG150608-MS
DNMG150612-MS
DNGG150404R
DNGG150404L
DNGG150408R
DNGG150408L
DNGG150604R
DNGG150604L
DNGG150608R
DNGG150608L
DNMG150408-RP
DNMG150412-RP
DNMG150416-RP
DNMG150608-RP
DNMG150612-RP
DNMG150616-RP
DNMG150408-RM
DNMG150412-RM
DNMG150416-RM
DNMG150608-RM
DNMG150612-RM
DNMG150616-RM
DNMG150408-RK
DNMG150412-RK
DNMG150608-RK
DNMG150612-RK
RP
0.7
Cast Iron
MS
Medium Cutting
Stainless Steel
Order Number
R/L
Steel
Shape
Medium Cutting
Heavy Cutting
Coated

Size
Applicable
Holder Page
Finish Cutting
DNMG 11 04 08- MS
Depth of Cut (mm)
DN
Depth of Cut (mm)
NEG
55
Depth of Cut (mm)
TURNING INSERTS
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
RE
(mm)
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Shape
Order Number
RS
DNMG150408-RS
DNMG150412-RS
DNMG150416-RS
DNMG150608-RS
DNMG150612-RS
DNMG150616-RS
DNMG150408-GH
DNMG150412-GH
DNMG150608-GH
DNMG150612-GH
0.8
1.2
1.6
0.8
1.2
1.6
DNMG150408-GJ
DNMG150412-GJ
DNMG150416-GJ
DNMG150608-GJ
DNMG150612-GJ
DNMG150616-GJ
DNMM150408-HZ
DNMM150412-HZ
DNMM150608-HZ
DNMM150612-HZ
0.8
1.2
a a
a a
1.6
a a
0.8
1.2
1.6
DNMA150404
DNMA150408
DNMA150412
DNMA150604
DNMA150608
DNMA150612
DNGA150404
DNGA150408
0.4
0.8
a a a a
1.2
a a a a
0.4
a a
0.8
1.2
a a a a
NEW
Rough Cutting
GH
0.8
1.2
a a [
a a
a a [
[ a
a a
0.8
a a [
a a
1.2
a a [
a a
Rough Cutting
HZ
0.8
1.2
a [
0.8
a [
1.2
a [
Flat Top
WITH
HOLE
C010
C011
E013
E036
040
H009
011
C010
C011
E013
E036
040
H009
011
C010
C011
E013
E036
040
H009
011
a [
Heavy Cutting
Flat Top
NEG
C010
C011
E013
E036
040
H009
011
Rough Cutting
GJ
Applicable
Holder Page
Work
Material
P
M
K
N
S
: Stable Cutting
TURNING INSERTS
a a a a
a
a
C010
C011
E013
E036
040
H009
011
a a
a a a a
0.4
0.8
C010
C011
E013
E036
040
H009
011
a a
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A103
5
4
Standard
3
2
1
0
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
Depth of Cut (mm)
8
6
5
4
Standard
3
2
1
0
0.1
0.3
0.5
Feed (mm/rev)
0.7
SH
6
5
GH
FH
Standard
3
HZ
2
MS
1
0
0.1
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
P
M
K
N
S
Thickness Corner Radius

8
6
Size
Medium Cutting
P Carbon Steel Alloy Steel (180280HB) M
Mild Steel
RNMG 12 04 00
: Stable Cutting
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Shape
Order Number
RE
(mm)
Standard
RNMG120400
Coated
Cermet Cermet
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Applicable
Holder Page
Depth of Cut (mm)
NEG
RN
TYPE INSERTS
WITH HOLE
Depth of Cut (mm)
TURNING INSERTS
a [
Medium Cutting
A104


Mild Steel
6
5
4
3
SY
2
1
0
0.1
0.3
0.5
Feed (mm/rev)
0.7
HX
6
5
FH
LP
4
3
RP
2
1
0
Light Cutting
Medium Cutting
MP
0.1
0.3
0.5
Feed (mm/rev)
MM
RM
5
4
3
2
1
0
0.7
LM
0.1
0.3
0.5
Feed (mm/rev)
Work
Material
Heavy Cutting

7
RK
Flat Top
6
5
4
3
LK
2
1
0
0.7
NEG
MK
0.1
0.3
0.5
Feed (mm/rev)
: Stable Cutting
P
M
K
N
S
Rough Cutting
Depth of Cut (mm)
HZ
Depth of Cut (mm)
Depth of Cut (mm)

0.7
: General Cutting
: Unstable Cutting
WITH
HOLE
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
RE
(mm)
Shape
Order Number
FH
SNMG090304-FH
SNMG090308-FH
SNMG120404-FH
SNMG120408-FH
0.4
0.8
SNMG120408-FS
0.8
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Applicable
Holder Page
Finish Cutting
Size
TURNING INSERTS
SN
SNMG 09 03 04- FH
Depth of Cut (mm)
90
TYPE INSERTS
WITH HOLE
a
a
0.4
0.8
a
a
C012
015
E014
E035
Finish Cutting
FS
C012
015
E014
E035
Finish Cutting
LP
SNMG120404-LP
SNMG120408-LP
SNMG120412-LP
0.4
0.8
a a
a a
a a
a a
1.2
a a
a a
C012
015
E014
E035
Light Cutting
LM
SNMG120404-LM
SNMG120408-LM
0.4
0.8
a a a
C012
015
a a a
E014
E035
Light Cutting
NEW
LK
SNMG120408-LK
SNMG120412-LK
0.8
1.2
a a
C012
015
a a
E014
E035
Light Cutting
SH
SNMG120404-SH
SNMG120408-SH
SNMG120412-SH
0.4
0.8
a a [
1.2
a [
C012
015
E014
E035
Light Cutting
SA
SNMG120404-SA
SNMG120408-SA
SNMG120412-SA
0.4
0.8
a a [
1.2
a [
C012
015
E014
E035
Light Cutting
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A105
SN
TYPE INSERTS
WITH HOLE

Mild Steel
HZ
6
5
4
3
SY
1
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
HX
6
5
FH
LP
4
3
RP
2
1
0
Light Cutting
Medium Cutting
MP
0.1
0.3
0.5
Feed (mm/rev)
0.7
MM
RM
5
4
3
2
1
LM
0.1
0.3
0.5
Feed (mm/rev)
Work
Material
SY
RK
Flat Top
6
5
4
3
LK
2
1
MK
0.1
0.3
0.5
Feed (mm/rev)
: Stable Cutting
0.7
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Order Number
RE
(mm)
SNMG120408-SY
0.8
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Shape
0.7
P
M
K
N
S
Heavy Cutting
Rough Cutting
Applicable
Holder Page

Depth of Cut (mm)
Size
Finish Cutting
SNMG 12 04 08- SY
Depth of Cut (mm)
Depth of Cut (mm)
NEG
90
Depth of Cut (mm)
TURNING INSERTS
C012
015
E014
E035
Light Cutting
SNMG090304-C
SNMG090308-C
SNMG120408-C
SNMG120416-C
0.4
0.8
0.8
[[
1.6
SNMG120404R-1G
SNMG120404L-1G
SNMG120408R-1G
0.4
0.4
0.8
C012
015
E014
E035
Light Cutting
R/L-1G
C012
015
E014
E035
Light Cutting
MP
SNMG120404-MP
SNMG120408-MP
SNMG120412-MP
0.4
0.8
a a [ a a
a a [ a a
1.2
a a [ a a
C012
015
E014
E035
Medium Cutting
MM
Medium Cutting
NEW
MK
Medium Cutting
A106
SNMG120408-MM
SNMG120412-MM
SNMG120416-MM
SNMG150608-MM
SNMG150612-MM
SNMG150616-MM
SNMG190612-MM
SNMG190616-MM
SNMG120408-MK
SNMG120412-MK
SNMG120416-MK
SNMG190612-MK
SNMG190616-MK

0.8
1.2
a a a
1.6
a a a
0.8
a a a
C012
015
1.2
a a a
E014
1.6
a a a
1.2
1.6
a a a
a a a
E035
a a a
0.8
1.2
a a
1.6
a a
1.2
1.6
a a
a a
a a
C012
015
E014
E035
Work
Material
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
NEW
Order Number
SNMG120404-GK
SNMG120408-GK
SNMG120412-GK
GK
RE
(mm)
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Shape
: Unstable Cutting
0.4
0.8
a a
1.2
a a
Applicable
Holder Page
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
C012
015
a a
NEG
WITH
HOLE
E014
E035
Medium Cutting
SNMG120404-GM
SNMG120408-GM
SNMG120412-GM
GM
0.4
0.8
a a a
1.2
a a a
C012
015
a a a
E014
E035
Medium Cutting
MA
Medium Cutting
MH
SNMG120404-MA
SNMG120408-MA
SNMG120412-MA
SNMG120416-MA
SNMG150608-MA
SNMG150612-MA
SNMG150616-MA
SNMG190612-MA
SNMG190616-MA
SNMG120408-MH
SNMG120412-MH
SNMG190612-MH
SNMG190616-MH
0.4
0.8
a a [ a a
a a
a a [ a a a
a a [ a
a a a a
1.2
a a [ a a
a a [ a
a a a a
SNMG090304
SNMG090308
SNMG120404
SNMG120408
SNMG120412
SNMG120416
SNMG120420
SNMG150612
SNMG190612
SNMG190616
SNMG090304-MS
SNMG090308-MS
SNMG120404-MS
SNMG120408-MS
SNMG120412-MS
SNMG120416-MS
SNMG150612-MS
SNMG150616-MS
SNMG190616-MS
1.6
a a
C012
015
0.8
a a [
1.2
a a [
1.6
1.2
1.6
a a [
a
0.8
1.2
a a [ a a
a a [ a a
1.2
a a [
1.6
a a [
0.4
0.8
a a [ a a
a a a
a a [ a a
a a a
a a a
0.4
a a [ a a
0.8
a a [ a a a
a a
1.2
a a [ a a
a a
a a
C012
015
1.6
a [ a a
a a
E014
2.0
[ a a
E014
a
E035
a a [
C012
015
E014
E035
Medium Cutting
Standard
Medium Cutting
MS
NEW
NEW
Medium Cutting
a a a
E035
1.2
a a [
a a
a a
1.2
1.6
a a [
a a
a a
a a [
a a
0.4
0.8
a a a
a
a
0.4
[ a
a a
0.8
a [
[ a a
a a a a a a
1.2
[ a a
a a a a a
a a
a a
1.6
a a
1.2
1.6
1.6
a
a
C012
015
E014
E035
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A107
SN
TYPE INSERTS
WITH HOLE

Mild Steel
HZ
6
5
4
3
SY
1
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
HX
6
5
FH
LP
4
3
RP
2
1
0
Light Cutting
Medium Cutting
MP
0.1
0.3
0.5
Feed (mm/rev)
MM
RM
5
4
3
2
1
LM
0.1
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
P
M
K
N
S

7
RK
5
4
3
LK
2
1
0
MK
0.1
: Stable Cutting
NEW
RK
Rough Cutting
NEW
RS
Rough Cutting
: General Cutting
: Unstable Cutting
Non-ferrous Metal
Coated
Cermet Cermet
RE
(mm)
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
SNGG090304R
SNGG090304L
SNGG090308R
SNGG090308L
SNGG120404R
SNGG120404L
SNGG120408R
SNGG120408L
SNMG120408-RP
SNMG120412-RP
SNMG120416-RP
SNMG150612-RP
SNMG150616-RP
SNMG190612-RP
SNMG190616-RP
SNMG120408-RM
SNMG120412-RM
SNMG120416-RM
SNMG150612-RM
SNMG150616-RM
SNMG190612-RM
SNMG190616-RM
SNMG120408-RK
SNMG120412-RK
SNMG120416-RK
SNMG190612-RK
SNMG190616-RK
SNMG120408-RS
SNMG120412-RS
SNMG120416-RS
SNMG150616-RS
SNMG190616-RS
Rough Cutting
0.7
Cast Iron
R/L
RM
0.5
Stainless Steel
Order Number
Rough Cutting
0.3
Feed (mm/rev)
Steel
Shape
RP
Flat Top
Coated
Medium Cutting
Heavy Cutting
0.7
Rough Cutting
0.4
0.4
a a
a a
0.8
a a
0.8
a a
0.4
a a a
0.4
a a a
0.8
0.8
a a a
a a a
0.8
1.2
a a
a a
a a
1.6
a a
a a
1.2
a a
a a
1.6
a a
a a
1.2
1.6
a a
a a
a a
a a
C012
015
E014
E035
a a
C012
015
E014
E035
0.8
1.2
a a a
1.6
a a a
1.2
a a a
1.6
a a a
1.2
1.6
a a a
a a a
C012
015
E014
E035
a a a
0.8
1.2
a a
1.6
a a
1.2
1.6
a a
C012
015
a a
E014
E035
a a
0.8
1.2
1.6
1.6
1.6
A108

Applicable
Holder Page

Depth of Cut (mm)
Size
Finish Cutting
SNMG 12 04 08- RP
Depth of Cut (mm)
Depth of Cut (mm)
NEG
90
Depth of Cut (mm)
TURNING INSERTS
C012
015
E014
E035
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
RE
(mm)
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Shape
Order Number
GH
SNMG120408-GH
SNMG120412-GH
SNMG120416-GH
SNMG150612-GH
SNMG150616-GH
SNMG190612-GH
SNMG190616-GH
SNMM120408-HZ
SNMM120412-HZ
SNMM150612-HZ
SNMM190612-HZ
SNMM190616-HZ
SNMM190612-HX
SNMM190616-HX
SNMM190624-HX
SNMM250724-HX
SNMM250924-HX
SNMM190616-HV
SNMM190624-HV
SNMM250724-HV
SNMM250924-HV
0.8
1.2
a a [
[ a
a a
a a [
[ a
a a
1.6
a a
1.2
a a
1.6
1.2
1.6
a a
a a
[ a
SNMA090304
SNMA090308
SNMA120408
SNMA120412
SNMA120416
SNMA190612
SNMA190616
SNGA090304
SNGA120404
SNGA120408
0.4
0.8
a a a a
0.8
a a a a
a a a
1.2
a a a a
1.6
a a a a
1.2
1.6
a a a a
Rough Cutting
HZ
Heavy Cutting
HX
Heavy Cutting
HV
Applicable
Holder Page
Work
Material
P
M
K
N
S
: Stable Cutting
TURNING INSERTS
NEG
WITH
HOLE
C012
015
E014
E035
0.8
1.2
a [
1.2
a [
1.2
1.6
a [
a [
1.2
1.6
a [
a [
2.4
a [
2.4
2.4
a [
a [
1.6
2.4
a [
a [
2.4
a [
2.4
a [
C012
015
a [
E014
E035
C012
014
C012
014
Heavy Cutting
Flat Top
Flat Top
C012
015
E014
E035
a a a a
0.4
0.4
0.8
a
a a
C012
015
E014
E035
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A109
TYPE INSERTS
WITH HOLE
Light Cutting
Medium Cutting
Mild Steel
FY
4
3
SY
2
1
0
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
FH
LP
4
3
RP
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
6
5
4
3
2
MW
1
0
0.7
SW
0.1
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
P
M
K
N
S
Depth of Cut (mm)
Depth of Cut (mm)
8
6
MM
RM
5
4
3
2
1
0
FH
LM
0.1
0.3
0.5
Feed (mm/rev)
: Stable Cutting
RK
Flat Top
6
5
4
3
LK
2
1
0
0.7
MK
0.1
: General Cutting
0.3
0.5
Feed (mm/rev)
0.7
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
RE
(mm)
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Order Number
TNMG110304-FH
TNMG160402-FH
TNMG160404-FH
TNMG160408-FH
0.4
0.2
a [
a a a
C017
0.4
a a a a
E014
0.8
a [
a a a a
TNMG160404-FS
TNMG160408-FS
0.4
0.8
C016
E035
E039
Finish Cutting
FS
Heavy Cutting
Coated
Shape
Rough Cutting
8
6

Size
Applicable
Holder Page
Finish Cutting
TNMG 11 03 04- FH
Depth of Cut (mm)
TN
Depth of Cut (mm)
NEG
60
Depth of Cut (mm)
TURNING INSERTS
C016
C017
E014
E035
E039
Finish Cutting
FY
TNMG160404-FY
TNMG160408-FY
0.4
0.8
a a
C016
C017
E014
E035
E039
Finish Cutting
PK
TNGG160404-PK
TNGG160408-PK
0.4
0.8
C016
C017
E014
E035
E039
Finish Cutting
R/L-FS
TNGG160402R-FS
TNGG160402L-FS
TNGG160404R-FS
TNGG160404L-FS
0.2
0.2
a
a
C017
0.4
E014
0.4
TNGG160402R-F
TNGG160402L-F
TNGG160404R-F
TNGG160404L-F
TNGG160408R-F
TNGG160408L-F
TNMG160404-LP
TNMG160408-LP
TNMG160412-LP
TNMG220408-LP
TNMG220412-LP
0.2
0.2
a a a
a a a
0.4
a a a
0.4
a a a
0.8
0.8
a a a
a a a
C016
E035
E039
Finish Cutting
R/L-F
Finish Cutting
LP
Light Cutting
A110

C016
C017
E014
E035
E039
0.4
0.8
a a
a a
a a
a a
C017
1.2
a a
a a
E014
0.8
1.2
a a
a a
a a
a a
C016
E035
E039
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
LM
Order Number
TNMG160404-LM
TNMG160408-LM
TNMG160412-LM
RE
(mm)
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Shape
: Unstable Cutting
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
0.4
0.8
a a a
a a a
C017
1.2
a a a
E014
C016
NEG
WITH
HOLE
E035
E039
Light Cutting
NEW
LK
TNMG160404-LK
TNMG160408-LK
TNMG160412-LK
0.4
0.8
a a
a a
C017
1.2
a a
E014
C016
E035
E039
Light Cutting
NEW
LS
TNMG160404-LS
TNMG160408-LS
0.4
0.8
a a
a a
C016
C017
E014
E035
E039
Light Cutting
SH
TNMG160404-SH
TNMG160408-SH
TNMG220408-SH
0.4
0.8
a a [ a a
a a
a a [ a a
a a
0.8
a a
C016
C017
E014
E035
E039
Light Cutting
SA
Light Cutting
SW
TNMG160404-SA
TNMG160408-SA
TNMG160412-SA
TNMG220408-SA
TNMG220412-SA
TNMX160404-SW
TNMX160408-SW
0.4
0.8
a a [ a a
a a [ a a
C017
1.2
a a [
E014
0.8
1.2
a a [
0.4
0.8
a a
a a a
a a
a a a
C016
E035
E039
C017
Light Cutting
(Wiper)
SY
TNMG160404-SY
TNMG160408-SY
0.4
0.8
a a
C016
C017
E014
E035
E039
Light Cutting
TNMG160404-C
TNMG160408-C
TNMG220404-C
TNMG220408-C
0.4
0.8
[[
[[
C017
0.4
[[
E014
0.8
TNMG160404R-1G
TNMG160404L-1G
TNMG220404R-1G
TNMG220404L-1G
0.4
0.4
a
a
C017
0.4
E014
0.4
C016
E035
E039
Light Cutting
R/L-1G
C016
E035
E039
Light Cutting
=
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A111
TYPE INSERTS
WITH HOLE
Light Cutting
Medium Cutting
Mild Steel
FY
4
3
SY
2
1
0
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
FH
LP
4
3
RP
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
0.7
6
5
4
3
SW
MW
1
0
0.1
0.3
0.5
Feed (mm/rev)
Depth of Cut (mm)
Depth of Cut (mm)
8
6
Work
Material
P
M
K
N
S
MM
RM
5
4
3
2
1
0.3

7
Flat Top
5
4
3
LK
2
1
0
0.7
RK
MK
0.1
: General Cutting
0.3
0.5
Feed (mm/rev)
0.7
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Order Number
R/L-K
TNGG160402R-K
TNGG160402L-K
TNGG160404R-K
TNGG160404L-K
TNGG160408R-K
TNGG160408L-K
TNMG160404-MJ
TNMG160408-MJ
TNMG160412-MJ
RE
(mm)
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Shape
MJ
0.5
Feed (mm/rev)
Coated
Light Cutting
LM
0.1
: Stable Cutting
Heavy Cutting
0.7
Rough Cutting
8
6

Size
0.2
0.2
a a a
0.4
a a a
0.4
a a
0.8
0.8
Applicable
Holder Page
Finish Cutting
TNMG 16 04 04 MJ
Depth of Cut (mm)
TN
Depth of Cut (mm)
NEG
60
Depth of Cut (mm)
TURNING INSERTS
C016
a a a
C017
E014
E035
E039
0.4
0.8
a a
a a
1.2
a a
C016
C017
E014
E035
E039
Light Cutting
MP
Medium Cutting
MM
Medium Cutting
NEW
MK
Medium Cutting
NEW
GK
Medium Cutting
GM
Medium Cutting
A112
TNMG160404-MP
TNMG160408-MP
TNMG160412-MP
TNMG220408-MP
TNMG220412-MP
TNMG160408-MM
TNMG160412-MM
TNMG220408-MM
TNMG220412-MM
TNMG220416-MM
TNMG160404-MK
TNMG160408-MK
TNMG160412-MK
TNMG220408-MK
TNMG220412-MK
TNMG220416-MK
TNMG160404-GK
TNMG160408-GK
TNMG160412-GK
TNMG220408-GK
TNMG220412-GK
TNMG160404-GM
TNMG160408-GM
TNMG160412-GM
TNMG220408-GM
TNMG220412-GM

0.4
0.8
a a [ a a
a a [ a a
C017
1.2
a a [ a a
E014
0.8
1.2
a a [ a a
a a [ a a
C016
E035
E039
0.8
1.2
a a a
a a a
C017
0.8
a a a
E014
1.2
1.6
a a a
C016
E035
E039
a a a
0.4
0.8
a a
1.2
a a
0.8
a a
1.2
1.6
a a
0.4
0.8
a a
a a
C017
1.2
a a
E014
0.8
1.2
a a
a a
C016
C017
E014
E035
E039
a a
a a
C016
E035
E039
0.4
0.8
a a a
a a a
C017
1.2
a a a
E014
0.8
1.2
a a a
a a a
C016
E035
E039
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Shape
Order Number
MA
TNMG160404-MA
TNMG160408-MA
TNMG160412-MA
TNMG160416-MA
TNMG220408-MA
TNMG220412-MA
TNMG220416-MA
TNMG270608-MA
TNMG270612-MA
TNMG160404-MH
TNMG160408-MH
TNMG160412-MH
TNMG220408-MH
TNMG220412-MH
TNMG110304
TNMG110308
TNMG160304
TNMG160308
TNMG160404
TNMG160408
TNMG160412
TNMG160416
TNMG220404
TNMG220408
TNMG220412
TNMG220416
TNMG270608
TNMG270612
TNMG270616
TNMG330924
TNMX160408-MW
TNMX160412-MW
MH
Medium Cutting
Flat Top
Medium Cutting
1 MW
RE
(mm)
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Medium Cutting
: Unstable Cutting
0.4
0.8
a a [ a a
a a [ a
a a a a
a a [ a a a
a a [ a
a a a a
1.2
a a [ a a
a a [ a
a a
1.6
C016
C017
0.8
a a [ a a a
a a [ a
a a a a
1.2
a a [ a a a
a a [ a
a a
E014
E035
E039
0.8
1.2
a a [
0.4
0.8
a a [
a a [ a a a
C017
1.2
a a [ a a a
E014
0.8
1.2
a a [
a a [
a a [
0.4
0.8
a [ a a
0.4
C016
E035
E039
a
a
a [ a a
a
0.8
a [ a a
0.4
a a [ a a
a a
a a a
a a a
0.8
a a [ a a a
a a
a a a
a a a
1.2
a a [ a a
a a
1.6
0.4
a a [ a a
0.8
a a [ a a a
1.2
a a [ a a
1.6
a [ a a
0.8
1.2
a [
1.6
2.4
a [
0.8
1.2
NEG
WITH
HOLE
1.6
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
C016
C017
a
a a
E014
E035
E039
a
a a
a a
a a
a a a a
C017
Medium Cutting
(Wiper)
*2 MS
Medium Cutting
R/L-ES
Medium Cutting
*
*
TNMG160404-MS
TNMG160408-MS
TNMG160412-MS
TNMG220408-MS
TNMG220412-MS
TNMG160404R-ES
TNMG160404L-ES
TNMG160408R-ES
TNMG160408L-ES
TNMG220408R-ES
TNMG220408L-ES
0.4
0.8
[ a a
a a a a a
a [
[ a a
a a a a a a
1.2
a a
0.8
1.2
[ a a
a
0.4
0.4
[ a
0.8
[ a
0.8
[ a
0.8
0.8
1 Please refer to A028 before using the MW breaker (wiper insert).

2 Newly designed breakers : MP9005, MP9015, MT9015
a
a
C016
a a
C017
a a a a
E014
a a a a a a
a a
E035
E039
C016
[ a
C017
E014
E035
E039
=
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A113
TYPE INSERTS
WITH HOLE
Light Cutting
Medium Cutting
Mild Steel
FY
4
3
SY
2
1
0
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
FH
LP
4
3
RP
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
6
5
4
3
2
MW
1
0
0.7
SW
0.1
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
P
M
K
N
S
Depth of Cut (mm)
Depth of Cut (mm)
8
6
Rough Cutting
8
6

Size

8
MM
RM
5
4
3
2
1
0
Heavy Cutting
LM
0.1
0.3
0.5
Feed (mm/rev)
: Stable Cutting
0.7
RK
5
4
3
LK
2
1
0
MK
0.1
0.3
0.5
Feed (mm/rev)
: General Cutting
0.7
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Shape
Order Number
R/L-2G
TNMG160404R-2G
TNMG160404L-2G
TNMG160408R-2G
TNMG160408L-2G
RE
(mm)
Coated
Cermet Cermet
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
0.4
0.4
a
a
C017
0.8
E014
0.8
C016
E035
E039
Medium Cutting
TNGG110302R
TNGG110302L
TNGG110304R
TNGG110304L
TNGG110308R
TNGG110308L
TNGG160304R
TNGG160304L
TNGG160402R
TNGG160402L
TNGG160404R
TNGG160404L
TNGG160408R
TNGG160408L
TNGG220404R
TNGG220404L
TNGG220408R
Medium Cutting TNGG220408L
TNMG160408-RP
RP
TNMG160412-RP
TNMG220408-RP
TNMG220412-RP
TNMG220416-RP
TNMG270612-RP
Rough Cutting TNMG270616-RP
TNMG160408-RM
RM
TNMG160412-RM
TNMG220408-RM
TNMG220412-RM
Rough Cutting TNMG220416-RM
R/L
A114
Flat Top

Applicable
Holder Page
Finish Cutting
TNMG 16 04 08 RP
Depth of Cut (mm)
TN
Depth of Cut (mm)
NEG
60
Depth of Cut (mm)
TURNING INSERTS
0.2
0.2
a a
0.4
a a
0.4
a a
0.8
0.8
a a
0.4
a a
0.4
a a
0.2
a a a
0.2
a a a
0.4
a a a
a a a
0.4
a a a
0.8
a a a
a a a
0.8
a a a
a a a
0.4
a a
0.4
a a
0.8
0.8
a a
a a
C016
a
C017
E014
E035
E039
0.8
1.2
a a
a a
a a
a a
0.8
a a
a a
C017
1.2
a a
a a
E014
1.6
a a
a a
1.2
1.6
a a
a a
a a
a a
C016
E035
E039
0.8
1.2
a a a
a a a
C017
0.8
a a a
E014
1.2
1.6
a a a
a a a
C016
E035
E039
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
RE
(mm)
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
Shape
Order Number
RK
TNMG160408-RK
TNMG160412-RK
TNMG160416-RK
TNMG220408-RK
TNMG220412-RK
TNMG220416-RK
TNMG160408-RS
TNMG160412-RS
TNMG220408-RS
TNMG220412-RS
0.8
1.2
a a
1.6
a a
0.8
a a
1.2
1.6
a a
TNMG160408-GH
TNMG160412-GH
TNMG220408-GH
TNMG220412-GH
TNMG220416-GH
TNMG270612-GH
TNMG270616-GH
TNMM160408-HZ
TNMM220408-HZ
TNMM220412-HZ
TNMM220416-HZ
0.8
1.2
a a [
0.8
a a [
C017
1.2
a a [
a a
E014
1.6
a a
1.2
1.6
a a [
0.8
0.8
a [
a [
C017
1.2
a [
E014
1.6
a [
TNMA160404
TNMA160408
TNMA160412
TNMA160416
TNMA160420
TNMA220404
TNMA220408
TNMA220412
TNMA220416
TNGA110304
TNGA110308
TNGA160402
TNGA160404
TNGA160408
TNGA220404
TNGA220408
0.4
0.8
a a a a
a a
a a a a
a a a
1.2
a a a a
1.6
a a
2.0
a a
NEW
Rough Cutting
NEW
RS
Rough Cutting
HZ
C016
a a
C017
E014
E035
E039
a a
0.8
1.2
C017
0.8
E014
1.2
Standard
C016
E035
E039
[ a
a a
a a
C016
E035
E039
a a
C016
E035
E039
Heavy Cutting
Standard
NEG
WITH
HOLE
Rough Cutting
GH
TURNING INSERTS
: Stable Cutting
C016
C017
E014
0.4
E035
0.8
a a a a
1.2
1.6
a a a a
a a a a
E039
0.4
0.8
0.2
C017
0.4
a a a
E014
0.8
a a
0.4
0.8
C016
E035
E039
a
a
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A115
Finish Cutting
Mild Steel
5
4
3
FS
1
0
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
6
5
FH
LP
4
3
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
MM
5
4
3
2
1
LM
0.1
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
P
M
K
N
S
Rough Cutting
Heavy Cutting

8
0.7
Medium Cutting
Flat Top
6
5
4
3
LK
2
1
0
MK
0.1
0.3
0.5
Feed (mm/rev)
: Stable Cutting
0.7
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Shape
Order Number
FH
VNMG160402-FH
VNMG160404-FH
VNMG160408-FH
RE
(mm)
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
0.2
0.4
a [
a a a
a [
0.8
a [
a a a a
Applicable
Holder Page
Depth of Cut (mm)
8
6
Light Cutting
Depth of Cut (mm)
Depth of Cut (mm)
NEG
VN
TYPE INSERTS VNMG 16 04 02- FH

Size Thickness Corner Radius Chip Breaker
WITH HOLE
* Please refer to page A002.
35
Depth of Cut (mm)
TURNING INSERTS
C018
020
a a
E015
E041
Finish Cutting
FS
VNMG160404-FS
VNMG160408-FS
0.4
0.8
C018
020
E015
E041
Finish Cutting
FJ
VNGG1604V5-FJ
VNGG160401-FJ
VNGG160402-FJ
0.05
0.1
0.2
C018
020
E015
E041
Finish Cutting
R/L-F
VNGG160402R-F
VNGG160402L-F
VNGG160404R-F
VNGG160404L-F
0.2
0.2
a a a
a a a
0.4
a a a
0.4
a a a
VNMG160404-LP
VNMG160408-LP
0.4
0.8
C018
020
E015
E041
Finish Cutting
LP
a a
a a
a a
a a
C018
020
E015
E041
Light Cutting
LM
VNMG160404-LM
VNMG160408-LM
0.4
0.8
a a a
C018
020
a a a
E015
E041
Light Cutting
NEW
LK
VNMG160404-LK
VNMG160408-LK
0.4
0.8
a a
a a
C018
020
E015
E041
Light Cutting
A116

Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Shape
Order Number
RE
(mm)
LS
VNMG160404-LS
VNMG160408-LS
0.4
0.8
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
NEW
: Unstable Cutting
a a
a a
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
C018
020
NEG
WITH
HOLE
E015
E041
Light Cutting
SH
VNMG160404-SH
VNMG160408-SH
0.4
0.8
a a [ a a
a a
a a [ a a
a a
C018
020
E015
E041
Light Cutting
MJ
VNMG160404-MJ
VNMG160408-MJ
VNMG160412-MJ
0.4
0.8
a a
a a
1.2
a a
C018
020
E015
E041
Light Cutting
MJ
VNGM160404-MJ
VNGM160408-MJ
0.4
0.8
C018
020
E015
E041
Light Cutting
MP
VNMG160404-MP
VNMG160408-MP
VNMG160412-MP
0.4
0.8
a a [ a a
a a [ a a
1.2
a a [ a a
C018
020
E015
E041
Medium Cutting
MM
VNMG160408-MM
0.8
a a a
C018
020
E015
E041
Medium Cutting
NEW
MK
VNMG160404-MK
VNMG160408-MK
VNMG160412-MK
0.4
0.8
a a
1.2
a a
C018
020
a a
E015
E041
Medium Cutting
NEW
GK
VNMG160404-GK
VNMG160408-GK
0.4
0.8
a a
C018
020
a a
E015
E041
Medium Cutting
GM
VNMG160404-GM
VNMG160408-GM
0.4
0.8
a a a
C018
020
a a a
E015
E041
Medium Cutting
=
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A117
Finish Cutting
Mild Steel
5
4
3
FS
1
0
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
6
5
FH
LP
4
3
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
MM
5
4
3
2
1
LM
0.1
0.3
0.5
Feed (mm/rev)
Work
Material
Heavy Cutting

7
Flat Top
6
5
4
3
LK
2
1
0
0.7
MK
0.1
0.3
0.5
Feed (mm/rev)
: Stable Cutting
P
M
K
N
S
Rough Cutting
0.7
Medium Cutting
0.7
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Shape
Order Number
RE
(mm)
MA
VNMG160404-MA
VNMG160408-MA
0.4
0.8
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
a a [ a a
a a [ a
a a a a
a a [ a a a
a a [ a
a a a a
Applicable
Holder Page
Depth of Cut (mm)
8
6
Light Cutting
Depth of Cut (mm)
Depth of Cut (mm)
NEG
VN
TYPE INSERTS VNMG 16 04 04- MA

WITH HOLE
35
Depth of Cut (mm)
TURNING INSERTS
C018
020
E015
E041
Medium Cutting
MH
VNMG160404-MH
VNMG160408-MH
0.4
0.8
a a [
a a [ a a
a
[
C018
020
E015
E041
Medium Cutting
Standard
VNMG160404
VNMG160408
VNMG160412
0.4
0.8
a a [ a a
a a
a a a
a a [ a a
a a
a a a
1.2
a a
a a
C018
020
E015
E041
Medium Cutting
MS
VNMG160404-MS
VNMG160408-MS
0.4
0.8
[ a a
a a a a
[ a a
a a a a
a
a
a a
C018
020
E015
E041
Medium Cutting
R/L
VNGG160404R
VNGG160404L
0.4
0.4
a a
a a
C018
020
E015
E041
Medium Cutting
Flat Top
VNGA160404
VNGA160408
0.4
0.8
a a
C018
020
a a
E015
E041
A118

Light Cutting
Medium Cutting
Mild Steel
FY
4
3
SY
2
1
0
0.1
0.3
0.5
Feed (mm/rev)
0.7
6
5
FH
LP
4
3
RP
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
6
5
4
3
2
MW
1
0
0.7
SW
0.1
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
P
M
K
N
S
Depth of Cut (mm)
Depth of Cut (mm)
Rough Cutting
Depth of Cut (mm)
Depth of Cut (mm)

8
MM
RM
5
4
3
2
1
0
Heavy Cutting
LM
0.1
0.3
0.5
Feed (mm/rev)
: Stable Cutting
Flat Top
5
4
3
LK
2
1
0
0.7
RK
MK
0.1
0.3
0.5
Feed (mm/rev)
: General Cutting
NEG
0.7
: Unstable Cutting
WITH
HOLE
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Shape
Order Number
RE
(mm)
FH
WNMG080404-FH
WNMG080408-FH
0.4
0.8
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
a a
Applicable
Holder Page
Finish Cutting

Size
TURNING INSERTS
WN
WNMG 08 04 04- FH
Depth of Cut (mm)
80
TYPE INSERTS
WITH HOLE
C021
E015
Finish Cutting
FS
WNMG080404-FS
WNMG080408-FS
0.4
0.8
C021
E015
Finish Cutting
FY
WNMG080404-FY
WNMG080408-FY
0.4
0.8
a
[
C021
E015
Finish Cutting
LP
Light Cutting
LM
WNMG060404-LP
WNMG060408-LP
WNMG06T304-LP
WNMG06T308-LP
WNMG080404-LP
WNMG080408-LP
WNMG080412-LP
WNMG060404-LM
WNMG060408-LM
WNMG080404-LM
WNMG080408-LM
0.4
0.8
a a
a a
a a
a a
0.4
a a
a a
0.8
a a
a a
E015
0.4
a a
a a
E037
0.8
1.2
a a
a a
a a
a a
WNMG080404-LK
WNMG080408-LK
WNMG080412-LK
0.4
0.8
a a
1.2
a a
WNMG080404-LS
WNMG080408-LS
0.4
0.8
0.4
0.8
a a a
0.4
a a a
0.8
a a a
C021
a a a
C021
E015
Light Cutting
NEW
LK
a a
C021
E015
Light Cutting
NEW
LS
a a
a a
C021
E015
Light Cutting
=
CHIP BREAKERS
A042
GRADES
A030
IDENTIFICATION
A002
A119
TYPE INSERTS
WITH HOLE
Light Cutting
Medium Cutting
Mild Steel
FY
4
3
SY
2
1
0
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
FH
LP
4
3
RP
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
6
5
4
3
2
MW
1
0
0.7
SW
0.1
0.3
0.5
Feed (mm/rev)
Depth of Cut (mm)
Depth of Cut (mm)
8
6
Work
Material
P
M
K
N
S
MM
RM
5
4
3
2
1
0.3
0.5
Feed (mm/rev)
RK
Flat Top
6
5
4
3
LK
2
1
0
0.7
MK
0.1
: General Cutting
0.3
0.5
Feed (mm/rev)
0.7
: Unstable Cutting
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
RE
(mm)
Shape
Order Number
SH
WNMG06T304-SH
WNMG06T308-SH
WNMG060404-SH
WNMG060408-SH
WNMG080404-SH
WNMG080408-SH
WNMG080412-SH
WNMG080404-SA
WNMG080408-SA
WNMG080412-SA
0.4
0.8
a a
a a
0.4
a a
0.8
a a
0.4
a a
a a
0.8
1.2
a a [ a a
a a [ a a
0.4
0.8
a a [ a a
a a [ a a
1.2
a a [ a a
WNMG060404-SW
WNMG060408-SW
WNMG080404-SW
WNMG080408-SW
WNMG080412-SW
WNMG080404-SY
WNMG080408-SY
0.4
0.8
a a
a a
0.4
a a
a a
a a a
0.8
1.2
a a
a a
a a a
a a
SA
Steel
Coated
Light Cutting
LM
0.1
: Stable Cutting
Heavy Cutting
0.7
Rough Cutting
8
6

Size
Applicable
Holder Page
Finish Cutting
WNMG 06 T3 04- SH
Depth of Cut (mm)
WN
Depth of Cut (mm)
NEG
80
Depth of Cut (mm)
TURNING INSERTS
C021
E015
E037
C021
E015
Light Cutting
SW
Light Cutting
(Wiper)
SY
0.4
0.8
C021
E015
a a a
a
a a
C021
E015
Light Cutting
WNMG080404-C
WNMG080408-C
0.4
0.8
[[
[
C021
E015
Light Cutting
MJ
WNMG080408-MJ
WNMG080412-MJ
WNMG080416-MJ
0.8
1.2
a a
a a
1.6
a a
Light Cutting
A120

C021
E015
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
RE
(mm)
Shape
Order Number
MP
WNMG06T304-MP
WNMG06T308-MP
WNMG06T312-MP
WNMG060404-MP
WNMG060408-MP
WNMG060412-MP
WNMG080404-MP
WNMG080408-MP
WNMG080412-MP
WNMG080416-MP
WNMG060408-MM
WNMG060412-MM
WNMG080408-MM
WNMG080412-MM
0.4
0.8
a a [ a a
a a [ a a
1.2
a a [ a a
0.4
a a [ a a
0.8
a a [ a a
1.2
a a [ a a
0.4
a a [ a a
0.8
a a [ a a
1.2
1.6
a a [ a a
a a [ a a
WNMG080404-MK
WNMG080408-MK
WNMG080412-MK
WNMG080416-MK
0.4
0.8
a a
1.2
a a
1.6
a a
WNMG060404-GK
WNMG060408-GK
WNMG080404-GK
WNMG080408-GK
WNMG080412-GK
WNMG060404-GM
WNMG060408-GM
WNMG080404-GM
WNMG080408-GM
WNMG080412-GM
WNMG06T304-MA
WNMG06T308-MA
WNMG06T312-MA
WNMG060404-MA
WNMG060408-MA
WNMG060412-MA
WNMG080404-MA
WNMG080408-MA
WNMG080412-MA
WNMG080416-MA
WNMG100612-MA
WNMG080404-MH
WNMG080408-MH
WNMG080412-MH
0.4
0.8
a a
0.4
a a
0.8
1.2
a a
MM
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Medium Cutting
: Unstable Cutting
0.8
1.2
a a a
0.8
a a a
1.2
a a a
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
NEG
WITH
HOLE
C021
E015
E037
a a a
C021
E015
Medium Cutting
NEW
MK
a a
C021
E015
Medium Cutting
NEW
GK
Medium Cutting
GM
Medium Cutting
MA
Medium Cutting
MH
a a
C021
E015
a a
0.4
0.8
a a a
0.4
a a a
0.8
1.2
a a a
a a a
C021
E015
a a a
0.4
0.8
a a
a a
1.2
a a
0.4
a a
0.8
a a
a a
a a
a a
1.2
a a
a a
a a
a a
0.4
a a [ a a
a a [ a
a a
0.8
a a [ a a a
a a [ a
a a a a
1.2
a a [ a a a
a a [ a
a a a a
1.6
1.2
a a
0.4
0.8
a a [
1.2
a a [ a a a
C021
E015
E037
a
[
a a [ a a a
C021
E015
Medium Cutting
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A121
TYPE INSERTS
WITH HOLE
Size
Light Cutting
Medium Cutting
Mild Steel
FY
4
3
SY
2
1
0
0.1
WITH
HOLE
0.3
0.5
Feed (mm/rev)
0.7
FH
LP
4
3
RP
2
1
0
MP
0.1
0.3
0.5
Feed (mm/rev)
6
5
4
3
SW
MW
1
0
0.7
Depth of Cut (mm)
Depth of Cut (mm)
8
6
0.1
0.3
0.5
Feed (mm/rev)
Work
Material
P
M
K
N
S
MM
RM
5
4
3
2
1
0.3
0.5
Feed (mm/rev)
Standard

7
Flat Top
5
4
3
LK
2
1
0
0.7
RK
MK
0.1
: General Cutting
0.3
0.5
Feed (mm/rev)
0.7
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Order Number
RE
(mm)
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Shape
LM
0.1
: Stable Cutting
Heavy Cutting
0.7
Rough Cutting
8
6

WNMG080404
WNMG080408
WNMG080412
WNMG080416
0.4
0.8
a a [ a a
a a
a a [ a a
a a
1.2
a a [ a a
a a
WNMG060408-MW
WNMG060412-MW
WNMG080408-MW
WNMG080412-MW
0.8
1.2
a a [ a a
0.8
a a [ a a
a a a a
1.2
a a
a a a a
WNMG06T304-MS
WNMG06T308-MS
WNMG060404-MS
WNMG060408-MS
WNMG080404-MS
WNMG080408-MS
WNMG080412-MS
WNMG080408-RP
WNMG080412-RP
0.4
0.8
[ a
[ a
0.4
[ a
0.8
[ a
0.4
a [
[ a
0.8
1.2
a [
[ a a
1.6
Applicable
Holder Page
Finish Cutting
WNMG 08 04 04
Depth of Cut (mm)
WN
Depth of Cut (mm)
NEG
80
Depth of Cut (mm)
TURNING INSERTS
C021
E015
Medium Cutting
*1 MW
Medium Cutting
(Wiper)
*2 MS
Medium Cutting
RP
0.8
1.2
a a
a a a a
a a
a a a a
a a
a
a a
a a
a a
E015
C021
E015
a a
a a a a a
a a
a a
C021
a a a a
E037
a a
a
C021
E015
Rough Cutting
RM
WNMG060408-RM
WNMG060412-RM
WNMG080408-RM
WNMG080412-RM
0.8
1.2
a a a
0.8
a a a
1.2
a a a
WNMG080408-RK
WNMG080412-RK
WNMG080416-RK
0.8
1.2
a a
1.6
a a
a a a
C021
E015
Rough Cutting
NEW
RK
a a
C021
E015
Rough Cutting
refer to A028 before using the MW breaker (wiper insert).
*21 Please
Newly designed breakers : MP9005, MP9015, MT9015
*
A122

: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
RE
(mm)
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
N
MP9005 EW
N
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Shape
Order Number
RS
WNMG080408-RS
WNMG080412-RS
WNMG080416-RS
WNMG100612-RS
0.8
1.2
1.6
1.2
WNMG080408-GH
WNMG080412-GH
0.8
1.2
NEW
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
NEG
WITH
HOLE
C021
E015
Rough Cutting
GH
a a [
[ a
a a
a a [
a a
C021
E015
Rough Cutting
GJ
WNMG080408-GJ
WNMG080412-GJ
WNMG080416-GJ
WNMG100612-GJ
0.8
1.2
1.6
WNMA080404
WNMA080408
WNMA080412
WNMA080416
0.4
0.8
a a a a
a a a a
1.2
a a a a
1.6
a a
1.2
C021
E015
Rough Cutting
Flat Top
C021
E015
CHIP BREAKERS
GRADES
IDENTIFICATION
A042
A030
A002
A123
SN
TYPE INSERTS
WITHOUT HOLE

K
Size

Heavy Cutting

8
7
6
5
4
Flat Top
3
2
1
0
0.1
WITHOUT
HOLE
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
P
M
K
N
S
: Stable Cutting
: General Cutting
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
RE
(mm)
Carbide
Shape
Order Number
Flat Top
SNMN120408
SNMN120412
SNMN120416
SNMN190412
0.8
1.2
a a a a
a a a a
1.6
a a a a
SNGN090308
SNGN120404
SNGN120408
0.8
0.4
0.8
Flat Top

: Unstable Cutting
Steel
Coated
A124
SNMN 12 04 08
1.2
Applicable
Holder Page
NEG
90
Depth of Cut (mm)
TURNING INSERTS
a
a
TN

K
TNMN 16 03 08
Size

Heavy Cutting

7
6
5
4
Flat Top
3
2
NEG
1
0
0.1
0.3
0.5
Feed (mm/rev)
0.7
: Stable Cutting
Work
Material
P
M
K
N
S
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Cermet Cermet
Shape
Order Number
Flat Top
TNMN160308
TNMN160408
TNMN160412
TNMN160416
TNMN160420
TNMN220408
TNMN220412
TNGN110304
TNGN110308
TNGN160404
TNGN160408
RE
(mm)
0.8
0.8
a a a a
1.2
a a a a
1.6
a a a a
2.0
0.8
1.2
Carbide
UE6105
UE6110
UE6020 N
MC6015 EW
MC6025
UE6035
UH6400
MC7015
MC7025
MP7035
US7020
US735
US905
N
MC5005 NEW
MC5015 EW
UC5105
UC5115 N
MP9005 NEW
MP9015 EW
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
UTi20T
HTi05T
HTi10
RT9010 N
MT9015 EW
Coated
Flat Top
: General Cutting
WITHOUT
HOLE
Applicable
Holder Page
Depth of Cut (mm)
TURNING INSERTS
60
TYPE INSERTS
WITHOUT HOLE
a
a
a
a
0.4
0.8
0.4
0.8
CHIP BREAKERS
GRADES
IDENTIFICATION
A068
A030
A002
A125
CC
TYPE INSERTS
WITH HOLE
Mild Steel
4
FP
LP
2
MP
1
0.1
0.2
0.3
Feed (mm/rev)
0.4
Light Cutting
Medium Cutting
FP
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
FM
LM
2
MM
1
0
0.4
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S

4
3
MK
2
1
0
0.1
Non-ferrous Metal
FJ
Finish Cutting
AZ
Medium Cutting
Finish Cutting
A126
RE
(mm)

Coated
Cermet
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
CCMT060202-FP
CCMT060204-FP
CCMT09T302-FP
CCMT09T304-FP
CCMT09T308-FP
CCMT060202-FM
CCMT060204-FM
CCMT09T302-FM
CCMT09T304-FM
CCMT09T308-FM
CCMT060202-FV
CCMT060204-FV
CCMT09T302-FV
CCMT09T304-FV
CCMT09T308-FV
CCGT0602V5-FJ
CCGT060201-FJ
CCGT060202-FJ
CCGT09T3V5-FJ
CCGT09T301-FJ
CCGT09T302-FJ
CCGT09T304-FJ
CCGT060202-AZ
CCGT060204-AZ
CCGT09T302-AZ
CCGT09T304-AZ
CCGT09T308-AZ
CCGT120402-AZ
CCGT120404-AZ
CCGT120408-AZ
Finish Cutting
: Unstable Cutting
Cast Iron
FP
FV
: General Cutting
Stainless Steel
Order Number
Finish Cutting
0.4
Steel
Shape
FM
0.3
: Stable Cutting
Coated
Finish Cutting
0.2
Feed (mm/rev)
Applicable
Holder Page
WITH
HOLE

Size
Depth of Cut (mm)
Finish Cutting
CCMT 06 02 02- FP
Depth of Cut (mm)
Depth of Cut (mm)
POSI
7
80
Depth of Cut (mm)
TURNING INSERTS
TURNING INSERTS [POSITIVE]
0.2
0.4
a a
a a
D008
0.2
a a
E006
0.4
0.8
a a
E030
a a
C022
E034
0.2
0.4
a
a
D008
0.2
E006
0.4
0.8
E030
C022
E034
0.2
0.4
a a
a a
D008
0.2
a a
E006
0.4
0.8
a a
E030
a a
C022
E034
0.05
0.1
0.2
0.05
0.1
0.2
0.4
C022
D008
E006
0.2
0.4
0.2
0.4
0.8
0.2
0.4
0.8
E030
E034
C022
D008
E006
E030
E034
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
L-F
Finish Cutting
R/L-F
Order Number
CCGT03S1V3L-F
*11 CCGT03S101L-F
*1 CCGT03S102L-F
*1 CCGT03S104L-F
*1 CCGT04T0V3L-F
*1 CCGT04T001L-F
*1 CCGT04T002L-F
*1 CCGT04T004L-F
*
RE
(mm)
Coated
Cermet
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
0.2
0.4
0.03
0.1
0.2
0.4
CCGH060202R-F
CCGH060202L-F
CCGH060204R-F
CCGH060204L-F
0.2
0.2
D008
0.4
E006
0.4
E030
CCMT060204-LP
CCMT060208-LP
CCMT09T304-LP
CCMT09T308-LP
0.4
0.8
a a
a a
D008
0.4
a a
E006
0.8
a a
E030
CCMT060204-LM
CCMT060208-LM
CCMT09T304-LM
CCMT09T308-LM
0.4
0.8
a a
a a
D008
0.4
a a
E006
0.8
a a
E030
CCMH060202-SV
CCMH060204-SV
0.2
0.4
E016
C022
E034
C022
E034
Light Cutting
SV
C022
E034
Light Cutting
LM
POSI
7
WITH
HOLE
0.03
0.1
Finish Cutting
LP
: Unstable Cutting
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
[ a
a a a
[ a
a a a
C022
D008
E006
E030
E034
Light Cutting
*2 SW
Light Cutting
(Wiper)
R/L-SS
Light Cutting
*
*
CCMT060202-SW
CCMT060204-SW
CCMT09T302-SW
CCMT09T304-SW
0.2
0.4
a [
a [
D008
0.2
a [
E006
0.4
a [
E030
CCGT0602V3R-SS
CCGT0602V3L-SS
CCGT060201R-SS
CCGT060201L-SS
CCGT060202R-SS
CCGT060202L-SS
CCGT09T3V3R-SS
CCGT09T3V3L-SS
CCGT09T301R-SS
CCGT09T301L-SS
CCGT09T302R-SS
CCGT09T302L-SS
0.03
0.03
0.1
0.1
0.2
0.2
0.03
0.03
0.1
0.1
0.2
0.2
C022
E034
C022
D008
E006
E030
E034
1 Diameter of inscribed circle is special. (For SCLC type)

2 Please refer to A028 before using the SW breaker (wiper insert).
CHIP BREAKERS
GRADES
IDENTIFICATION
A054
A030
A002
A127
CC
TYPE INSERTS
WITH HOLE
Mild Steel
4
FP
LP
2
MP
1
0.1
0.2
0.3
Feed (mm/rev)
0.4
Light Cutting
Medium Cutting

4
4
FP
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
LM
2
MM
1
0
0.4
FM
0.1
0.2
0.3
Feed (mm/rev)
Work
Material
MK
2
1
0
0.4
0.1
Non-ferrous Metal
Medium Cutting
Standard
Medium Cutting
MV
RE
(mm)
Coated
Cermet
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
CCMT060204-MK
CCMT060208-MK
CCMT09T304-MK
CCMT09T308-MK
CCMT120404-MK
CCMT120408-MK
CCMT060204-MP
CCMT060208-MP
CCMT09T304-MP
CCMT09T308-MP
CCMT120404-MP
CCMT120408-MP
CCMT120412-MP
CCMT060204-MM
CCMT060208-MM
CCMT09T304-MM
CCMT09T308-MM
CCMT120404-MM
CCMT120408-MM
CCMT120412-MM
CCMT060202
CCMT060204
CCMT060208
CCMT080302
CCMT080304
CCMT080308
CCMT09T302
CCMT09T304
CCMT09T308
CCMT120404
CCMT120408
CCMT120412
CCMH060202-MV
CCMH060204-MV
MM
: Unstable Cutting
Cast Iron
MK
Medium Cutting
: General Cutting
Stainless Steel
Order Number
MP
0.4
Steel
Shape
Medium Cutting
0.3
: Stable Cutting
Coated
NEW
0.2
Feed (mm/rev)
P
M
K
N
S
0.4
0.8
a a
0.4
a a
0.8
a a
0.4
0.8
a a
Applicable
Holder Page
WITH
HOLE

Size
Depth of Cut (mm)
Finish Cutting
CCMT 06 02 04- MK
Depth of Cut (mm)
Depth of Cut (mm)
POSI
7
80
Depth of Cut (mm)
TURNING INSERTS
C022
a a
D008
E006
E030
E034
a a
0.4
0.8
a a
a a
0.4
a a
D008
0.8
a a
E006
0.4
a a
E030
0.8
1.2
a a
a a
C022
E034
0.4
0.8
a a
a a
0.4
a a
D008
0.8
a a
E006
0.4
a a
E030
0.8
1.2
a a
a a
C022
E034
0.2
0.4
a [
a a a a
a a [
a a a a
0.8
a [
0.2
0.4
a a a a
0.8
0.2
a [
0.4
a a [
a a a a
0.8
a a [
a a a a
0.4
a a [
a a a a
0.8
1.2
a a [
a a a
a [
0.2
0.4
[ a
a a a a
[ a
a a a a
a
a a a a
C022
D008
E006
E030
E034
C022
D008
E006
E030
A128
Medium Cutting
E034
[
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Order Number
MW
CCMT060204-MW
CCMT060208-MW
CCMT09T304-MW
CCMT09T308-MW
CCMT120404-MW
CCMT120408-MW
CCET0602V3R-SR
CCET0602V3L-SR
CCET060201R-SR
CCET060201L-SR
CCET060202R-SR
CCET060202L-SR
CCET060204R-SR
CCET060204L-SR
CCET09T3V3R-SR
CCET09T3V3L-SR
CCET09T301R-SR
CCET09T301L-SR
CCET09T302R-SR
CCET09T302L-SR
CCET09T304R-SR
CCET09T304L-SR
CCET060200R-SN
CCET060200L-SN
CCET0602V3R-SN
CCET0602V3L-SN
CCET060201R-SN
CCET060201L-SN
CCET060202R-SN
CCET060202L-SN
CCET060204R-SN
CCET060204L-SN
CCET09T300R-SN
CCET09T300L-SN
CCET09T3V3R-SN
CCET09T3V3L-SN
CCET09T301R-SN
CCET09T301L-SN
CCET09T302R-SN
CCET09T302L-SN
CCET09T304R-SN
CCET09T304L-SN
R/L-SR
Medium Cutting
R/L-SN
Medium Cutting
RE
(mm)
Coated
Cermet
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
Medium Cutting
(Wiper)
: Unstable Cutting
0.4
0.8
a [
0.4
a [
0.8
a [
0.4
0.8
a [
a [
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
POSI
7
WITH
HOLE
C022
D008
E006
E030
E034
0.03
0.03
0.1
0.1
0.2
0.2
0.4
0.4
0.03
0.03
0.1
0.1
0.2
0.2
0.4
0.4
0
0
0.03
0.03
0.1
0.1
0.2
0.2
0.4
0.4
0.03
0.03
0.1
0.1
0.2
0.2
0.4
0.4
C022
D008
E006
E030
E034
C022
D008
E006
E030
E034
* Please refer to A028 before using the MW breaker (wiper insert).
CHIP BREAKERS
GRADES
IDENTIFICATION
A054
A030
A002
A129
CC
TYPE INSERTS
WITH HOLE
Mild Steel
4
FP
LP
2
MP
1
0.1
0.2
0.3
Feed (mm/rev)
0.4
Light Cutting
Medium Cutting

4
4
FP
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
FM
LM
2
MM
1
0
0.1
0.2
0.3
Feed (mm/rev)
Work
Material
3
MK
2
1
0
0.4
0.1
0.3
: Stable Cutting
0.4
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Order Number
R/L-SN CCGT0602V3R-SN
CCGT060201R-SN
CCGT060201L-SN
CCGT060202R-SN
CCGT060202L-SN
CCGT09T3V3R-SN
CCGT09T3V3L-SN
CCGT09T301R-SN
CCGT09T301L-SN
CCGT09T302R-SN
CCGT09T302L-SN
CCGT09T304R-SN
Medium Cutting CCGT09T304L-SN
R/LW-SN CCET0602V3RW-SN
CCET0602V3LW-SN
CCET09T3V3RW-SN
CCET09T3V3LW-SN
Medium Cutting
RE
(mm)
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
0.2
Feed (mm/rev)
P
M
K
N
S

0.03
0.1
0.1
0.2
0.2
0.03
D008
0.03
E006
0.1
E030
0.1
0.2
0.2
0.4
0.4
0.03
0.03
a
a
D008
0.03
E006
0.03
E030
C022
E034
C022
E034
(Wiper)
SMG
Applicable
Holder Page
WITH
HOLE
Size
Depth of Cut (mm)
Finish Cutting
CCGT 06 02 02 SMG
Depth of Cut (mm)
Depth of Cut (mm)
POSI
7
80
Depth of Cut (mm)
TURNING INSERTS
CCGT060202M-SMG 0.2
CCGT060204M-SMG 0.4
C022
D008
E006
E030
E034
Medium Cutting
Flat Top CCMW060202

CCMW060204
W
NE CCMW060208
CCMW09T304
CCMW09T308
W
NE CCMW09T312
CCMW120404
CCMW120408
CCMW120412
Flat Top CCGW060200
CCGW0602V5
CCGW09T300
CCGW09T3V5
A130 *
0.2
0.4
a a a a
0.8
a a
0.4
a a a a
0.8
a a a a
1.2
a a
0.4
a a a a
0.8
1.2
a a a a
a a
C022
a
D008
E006
E030
E034
0
0.05
a
a
D008
E006
0.05
E030
Please refer to A028 before using the R/LW-SN breaker (wiper insert).
a : Inventory maintained in Japan. [ : Inventory maintained in Japan. To be replaced by new products.
C022
E034
CHIP BREAKERS
A054
CP
Mild Steel
FV
2
MV
SV
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
3
FV
2
MV
SV
1
0
Light Cutting
0.1
0.2
0.3
Feed (mm/rev)
3
FV
2
Work
Material
POSI
11
1
0
0.4
MV
SV
0.1
0.2
0.3
Feed (mm/rev)
0.4
P
M
K
N
S
Medium Cutting
Depth of Cut (mm)

Depth of Cut (mm)
Depth of Cut (mm)
Size
: Stable Cutting
: General Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
RE
(mm)
Cermet
Shape
Order Number
FV
CPMH080202-FV
CPMH080204-FV
CPMH090302-FV
CPMH090304-FV
CPMH090308-FV
CPMH080204R-F
CPMH080204L-F
CPMH090304R-F
CPMH090304L-F
0.2
0.4
a a a
a a a
0.2
a a a
0.4
0.8
a a a
CPGT080204R-F
CPGT080204L-F
CPGT090302R-F
CPGT090302L-F
CPGT090304R-F
CPGT090304L-F
CPGT080202
CPGT080204
CPGT090302
CPGT090304
0.4
0.4
0.2
0.2
0.4
0.4
CPMH080202-SV
CPMH080204-SV
CPMH090302-SV
CPMH090304-SV
CPMH090308-SV
CPMX080204
CPMX080208
CPMX090304
CPMX090308
0.2
0.4
[ a
a a a
[ a
a a a
0.2
[ a
a a a
0.4
0.8
[ a
a a a
[ a
a a a
CPMH080204-MV
CPMH080208-MV
CPMH090304-MV
CPMH090308-MV
Finish Cutting
R/L-F
: Unstable Cutting
WITH
HOLE
Applicable
Holder Page
Finish Cutting
CPMH 08 02 02- FV
TURNING INSERTS
80
TYPE INSERTS
WITH HOLE
E006
a a a
0.4
0.4
0.4
0.4
a
a
E006
Finish Cutting
R/L-F
Finish Cutting
Standard
0.2
0.4
0.2
0.4
Finish Cutting
SV
Light Cutting
Standard
E006
0.4
0.8
0.4
a a
0.8
a [
0.4
0.8
[ a
a a a a
[ a
a a a a
0.4
[ a
a a a a
0.8
[ a
a a a a
Medium Cutting
MV
E006
Medium Cutting
CHIP BREAKERS
GRADES
IDENTIFICATION
A062
A030
A002
A131
DC
TYPE INSERTS
WITH HOLE
Mild Steel
4
FP
LP
2
MP
1
0.1
0.2
0.3
Feed (mm/rev)
0.4
Medium Cutting
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
FM
LM
2
MM
1
0
0.4
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S

4
4
FP
3
MK
2
1
0
0.1
: Stable Cutting
AZ
Medium Cutting
Finish Cutting
R/L-F
Finish Cutting
LP

Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
RE
(mm)
Coated
Cermet
Cermet
0.2
0.4
a a
a a
0.2
a a
0.4
0.8
a a
a a
0.2
0.4
0.2
0.4
0.8
C023
D009
D026
E008
E009
E029
E031
C023
D009
D026
E008
E009
E029
E031
0.2
0.4
a [
a a
a [
a a
0.8
a a
0.2
a a
0.4
0.8
a [
a a
a [
a a
C023
D009
D026
E008
E009
E029
E031
0.2
0.4
0.2
0.4
0.8
0.2
0.2
0.4
0.4
0.2
0.2
0.4
0.4
a
a
a
a
C023
D009
D026
E008
E009
E029
E031
a
a
0.4
0.8
a a
a a
0.4
a a
0.8
a a
C023
D009
D026
E008
E009
E029
E031
Light Cutting
A132
: Unstable Cutting
Non-ferrous Metal
DCMT070202-FP
DCMT070204-FP
DCMT11T302-FP
DCMT11T304-FP
DCMT11T308-FP
DCMT070202-FM
DCMT070204-FM
DCMT11T302-FM
DCMT11T304-FM
DCMT11T308-FM
DCMT070202-FV
DCMT070204-FV
DCMT070208-FV
DCMT11T302-FV
DCMT11T304-FV
DCMT11T308-FV
DCGT070202-AZ
DCGT070204-AZ
DCGT11T302-AZ
DCGT11T304-AZ
DCGT11T308-AZ
DCGT070202R-F
DCGT070202L-F
DCGT070204R-F
DCGT070204L-F
DCGT11T302R-F
DCGT11T302L-F
DCGT11T304R-F
DCGT11T304L-F
DCMT070204-LP
DCMT070208-LP
DCMT11T304-LP
DCMT11T308-LP
Finish Cutting
: General Cutting
Cast Iron
FP
FV
0.4
Stainless Steel
Order Number
Finish Cutting
0.3
Steel
Shape
FM
0.2
Feed (mm/rev)
Coated
Finish Cutting

Applicable
Holder Page
WITH
HOLE
Size
Light Cutting
Depth of Cut (mm)
Finish Cutting
DCMT 07 02 02- FP
Depth of Cut (mm)
Depth of Cut (mm)
POSI
7
55
Depth of Cut (mm)
TURNING INSERTS
C023
D009
D026
E008
E009
E029
E031
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
RE
(mm)
Coated
Cermet
Cermet
Shape
Order Number
LM
DCMT070204-LM
DCMT070208-LM
DCMT11T304-LM
DCMT11T308-LM
0.4
0.8
a a
a a
0.4
a a
0.8
a a
DCMT070202-SV
DCMT070204-SV
DCMT070208-SV
DCMT11T302-SV
DCMT11T304-SV
DCMT11T308-SV
DCGT0702V3R-SS
DCGT0702V3L-SS
DCGT070201R-SS
DCGT070201L-SS
DCGT070202R-SS
DCGT070202L-SS
DCGT11T3V3R-SS
DCGT11T301R-SS
DCGT11T302R-SS
DCMT070204-MK
DCMT11T304-MK
DCMT11T308-MK
DCMT150404-MK
DCMT150408-MK
DCMT070204-MP
DCMT070208-MP
DCMT11T304-MP
DCMT11T308-MP
DCMT150404-MP
DCMT150408-MP
DCMT070204-MM
DCMT070208-MM
DCMT11T304-MM
DCMT11T308-MM
DCMT150404-MM
DCMT150408-MM
DCMT070202
DCMT070204
DCMT070208
DCMT11T302
DCMT11T304
DCMT11T308
DCMT11T312
DCMT150404
DCMT150408
DCMT150412
0.2
0.4
[ a
a a
a [
[ a
a a
0.8
a [
[ a
a a
0.2
a [
[ a
a a
0.4
0.8
a [
[ a
a a
a [
[ a
a a
C023
D009
D026
E008
E009
E029
E031
Light Cutting
SV
Light Cutting
R/L-SS
Light Cutting
NEW
MK
Medium Cutting
MP
Medium Cutting
MM
Medium Cutting
Standard
Medium Cutting
: Unstable Cutting
0.03
0.03
0.1
0.1
0.2
0.2
0.03
0.1
0.2
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
POSI
7
WITH
HOLE
C023
D009
D026
E008
E009
E029
E031
C023
D009
D026
E008
E009
E029
E031
0.4
0.4
a a
0.8
a a
0.4
0.8
a a
C023
D009
D026
E008
E009
E029
E031
a a
a a
0.4
0.8
a a
a a
0.4
a a
0.8
a a
0.4
0.8
a a
a a
0.4
0.8
a a
a a
0.4
a a
0.8
a a
0.4
0.8
a a
a a
C023
D009
D026
E008
E009
E029
E031
C023
D009
D026
E008
E009
E029
E031
0.2
0.4
a [
a a [
0.8
0.2
a [
0.4
a a [
0.8
a a [
1.2
0.4
a [
0.8
1.2
a [
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a
C023
D009
D026
E008
E009
E029
E031
CHIP BREAKERS
GRADES
IDENTIFICATION
A054
A030
A002
A133
DC
TYPE INSERTS
WITH HOLE
Mild Steel
4
FP
LP
2
MP
1
0.1
0.2
0.3
Feed (mm/rev)
0.4
Medium Cutting
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
FM
LM
2
MM
1
0
0.4
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S

4
4
FP
3
MK
2
1
0
0.1
: Stable Cutting
A134
: Unstable Cutting
Non-ferrous Metal
RE
(mm)

Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
DCMT070202-MV
DCMT070204-MV
DCMT070208-MV
DCMT11T302-MV
DCMT11T304-MV
DCMT11T308-MV
DCET0702V3R-SR
DCET0702V3L-SR
DCET070201R-SR
DCET070201L-SR
DCET070202R-SR
DCET070202L-SR
DCET070204R-SR
DCET070204L-SR
DCET11T3V3R-SR
DCET11T3V3L-SR
DCET11T301R-SR
DCET11T301L-SR
DCET11T302R-SR
DCET11T302L-SR
DCET11T304R-SR
DCET11T304L-SR
DCET070200R-SN
DCET070200L-SN
DCET0702V3R-SN
DCET0702V3L-SN
DCET070201R-SN
DCET070201L-SN
DCET070202R-SN
DCET070202L-SN
DCET070204R-SN
DCET070204L-SN
DCET11T300R-SN
DCET11T300L-SN
DCET11T3V3R-SN
DCET11T3V3L-SN
Medium Cutting
: General Cutting
Cast Iron
MV
R/L-SN
0.4
Stainless Steel
Order Number
Medium Cutting
0.3
Steel
Shape
R/L-SR
0.2
Feed (mm/rev)
Coated
Medium Cutting

0.2
0.4
a [
[ a
a a a a
a [
[ a
a a a a
0.8
a [
[ a
a a a a
0.2
a [
[ a
a a a a
0.4
0.8
a [
[ a
a a a a
a [
[ a
a a a a
0.03
0.03
0.1
0.1
0.2
0.2
0.4
0.4
0.03
0.03
0.1
0.1
0.2
0.2
0.4
0.4
0
0
0.03
0.03
0.1
0.1
0.2
0.2
0.4
0.4
0.03
0.03
Applicable
Holder Page
WITH
HOLE
Size
Light Cutting
Depth of Cut (mm)
Finish Cutting
DCMT 07 02 02- MV
Depth of Cut (mm)
Depth of Cut (mm)
POSI
7
55
Depth of Cut (mm)
TURNING INSERTS
C023
D009
D026
E008
E009
E029
E031
C023
D009
D026
E008
E009
E029
E031
C023
D009
D026
E008
E009
E029
E031
Stainless Steel
Cast Iron
Non-ferrous Metal
R/L-SN
Medium Cutting
R/LW-SN
Medium Cutting
(Wiper)
SMG
DCET11T301L-SN
DCET11T302R-SN
DCET11T302L-SN
DCET11T304R-SN
DCET11T304L-SN
DCGT0702V3R-SN
DCGT070201R-SN
DCGT070202R-SN
DCGT070202L-SN
DCGT11T3V3R-SN
DCGT11T3V3L-SN
DCGT11T301R-SN
DCGT11T301L-SN
DCGT11T302R-SN
DCGT11T302L-SN
DCGT11T304R-SN
DCGT11T304L-SN
DCET0702V3RW-SN
DCET0702V3LW-SN
DCET11T3V3RW-SN
DCET11T3V3LW-SN
DCGT070202M-SMG
DCGT070204M-SMG
DCGT11T302M-SMG
DCGT11T304M-SMG
RE
(mm)
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Order Number
R/L-SN DCET11T301R-SN
Medium Cutting
: Unstable Cutting
Steel
Coated
Shape
: General Cutting
0.1
0.1
a
a
0.2
0.2
0.4
0.4
0.03
0.1
0.2
0.2
0.03
0.03
0.1
0.1
0.2
0.2
0.4
0.4
0.03
0.03
0.03
0.03
0.2
0.4
0.2
0.4
DCMW11T304
DCMW11T308
DCMW150404
DCMW150408
Flat Top DCGW070200
DCGW0702V5
DCGW11T300
DCGW11T3V5
C023
D009
D026
E008
E009
E029
E031
POSI
7
WITH
HOLE
C023
D009
D026
E008
E009
E029
E031
C023
D009
D026
E008
E009
E029
E031
C023
D009
D026
E008
E009
E029
E031
Medium Cutting
Flat Top DCMW070204
Applicable
Holder Page
Work
Material
P
M
K
N
S
: Stable Cutting
TURNING INSERTS
0.4
0.4
a a a a
0.8
a a a a
a a a a
a
a
0.4
0.8
a
a
0
0.05
0.05
C023
D009
D026
E008
E009
E029
E031
C023
D009
D026
E008
E009
E029
E031
* Please refer to A028 before using the R/LW-SN breaker (wiper insert).
CHIP BREAKERS
GRADES
IDENTIFICATION
A054
A030
A002
A135
DE
TYPE INSERTS
WITH HOLE

N
Finish Cutting
Size
Thickness Corner Radius R/L

Medium Cutting
Aluminium Alloy
4
3
R/L
R/L-F
1
0
0.1
0.2
0.3
Feed (mm/rev)
WITH
HOLE
0.4
Work
Material
P
M
K
N
S
: Stable Cutting
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
RE
(mm)
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Coated
Shape
Order Number
R/L-F
DEGX150402R-F
DEGX150402L-F
DEGX150404R-F
DEGX150404L-F
0.2
0.2
0.4
0.4
DEGX150402R
DEGX150402L
DEGX150404R
DEGX150404L
0.2
0.2
0.4
0.4
Finish Cutting
(For Aluminium Alloy)
R/L
Medium Cutting

a
A136
DEGX 15 04 02 R
Applicable
Holder Page
POSI
20
55
Depth of Cut (mm)
TURNING INSERTS
C032
C032

CHIP BREAKERS
A066

8
6
5
4
Standard
2
1
0
0.1
0.3
0.5
Feed (mm/rev)
0.7
RR
6
5
4
3
2
Standard
1
0
0.1
0.3
0.5
Feed (mm/rev)
0.7
Heavy Cutting

8
7
6
5
4
3
Standard
POSI
7
2
1
0
0.1
0.3
0.5
Feed (mm/rev)
0.7
Work
Material
P
M
K
N
S

: Stable Cutting
: General Cutting
: Unstable Cutting
WITH
HOLE
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Order Number
RE
(mm)
AZ
RCGT0803M0-AZ
RCGT10T3M0-AZ
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
Cermet
Applicable
Holder Page
Depth of Cut (mm)
Depth of Cut (mm)
Mild Steel
8
Size
Medium Cutting
Depth of Cut (mm)
RCGT 08 03 M0- AZ
TURNING INSERTS
RC
TYPE INSERTS
WITH HOLE
a
a
C025
Medium Cutting
Finish Cutting
Standard
RCMT0602M0
RCMT0803M0
a
a
a a a
a a a
C025
Medium Cutting
Standard
Medium Cutting
RR
RCMX1003M0
RCMX1204M0
RCMX1606M0
RCMX2006M0
RCMX2507M0
RCMX3209M0
RCMX1606M0-RR
RCMX2006M0-RR
RCMX2507M0-RR
RCMX3209M0-RR
a a [
a a [
a a
a a [
a a [
a [
a [
a [
a [
a [
a
a a
a a a
a a a
a a a
a a
C024
H012
a a [
Heavy Cutting
CHIP BREAKERS
GRADES
IDENTIFICATION
A054
A030
A002
A137
TYPE INSERTS
WITH HOLE
Mild Steel
4
FP
LP
2
MP
1
0.1
0.2
0.3
Feed (mm/rev)
0.4
Light Cutting
Medium Cutting
FP
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
FM
LM
2
MM
1
0
0.4
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S

4
3
MK
2
1
0
0.1
0.2
0.3
0.4
Feed (mm/rev)
: Stable Cutting
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Order Number
RE
(mm)
FP
SCMT09T304-FP
SCMT09T308-FP
0.4
0.8
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
Coated
Cermet
Cermet
a a
a a
Applicable
Holder Page
WITH
HOLE

Size
Depth of Cut (mm)
Finish Cutting
SCMT 09 T3 04- FP
Depth of Cut (mm)
Depth of Cut (mm)
POSI
7
SC
90
Depth of Cut (mm)
TURNING INSERTS
C026
E033
Finish Cutting
FM
SCMT09T304-FM
SCMT09T308-FM
0.4
0.8
a
a
C026
E033
Finish Cutting
FV
SCMT09T304-FV
0.4
a a
C026
E033
Finish Cutting
LP
SCMT09T304-LP
SCMT09T308-LP
0.4
0.8
a a
a a
C026
E033
Light Cutting
LM
SCMT09T304-LM
SCMT09T308-LM
0.4
0.8
a a
a a
C026
E033
Light Cutting
NEW
MK
SCMT09T304-MK
SCMT09T308-MK
SCMT120408-MK
0.4
0.8
a a
0.8
a a
SCMT09T304-MP
SCMT09T308-MP
SCMT120404-MP
SCMT120408-MP
0.4
0.8
a a
a a
0.4
a a
0.8
a a
a a
C026
E033
Medium Cutting
MP
Medium Cutting
A138

C026
E033
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
RE
(mm)
Cermet
Shape
Order Number
MM
SCMT09T304-MM
SCMT09T308-MM
SCMT120404-MM
SCMT120408-MM
0.4
0.8
a a
a a
0.4
a a
0.8
a a
SCMT09T304
SCMT09T308
SCMT120404
SCMT120408
SCMT120412
SCMW09T304
SCMW09T308
SCMW120408
0.4
0.8
a a [
a a a a
a a [
a a a a
0.4
a a [
a a a
0.8
1.2
a a [
a a a a
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
POSI
7
WITH
HOLE
C026
E033
Medium Cutting
Standard
Medium Cutting
Flat Top
C026
E033
a
0.4
0.8
a a
0.8
a a a a
a a a a
C026
E033
CHIP BREAKERS
GRADES
IDENTIFICATION
A054
A030
A002
A139
SP
TYPE INSERTS
WITH HOLE
2
1
0
0.1
0.2
0.3
Feed (mm/rev)
WITH
HOLE
0.4
3
Standard
2
1
0
Depth of Cut (mm)
Standard
0.1
0.2
0.3
Feed (mm/rev)
0.4
3
Standard
2
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S

Size
Medium Cutting
Mild Steel
4
SPMT 09 03 04
: Stable Cutting
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
RE
(mm)
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Coated
Shape
Order Number
Standard
SPMT090304
SPMT090308
SPMT120308
0.4
0.8
0.8
SPMW090304
SPMW090308
SPMW120304
SPMW120308
0.4
0.8
a a a
a a a
0.4
a a a
0.8
a a a
SPGX090304
SPGX090308
SPGX120304
SPGX120308
0.4
0.8
Applicable
Holder Page
Depth of Cut (mm)
POSI
11
90
Depth of Cut (mm)
TURNING INSERTS
M006
Medium Cutting
Flat Top
Flat Top

a
A140
L113
a
a
0.4
0.8
M006

CHIP BREAKERS
A062
Mild Steel
FP
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
Medium Cutting
FP
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
FM
LM
2
MM
1
0
0.4
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S

4
Depth of Cut (mm)
Light Cutting
Depth of Cut (mm)
Depth of Cut (mm)
3
MK
2
0.1
: Stable Cutting
: General Cutting
: Unstable Cutting
WITH
HOLE
Cast Iron
Non-ferrous Metal
TCMT090202-FP
TCMT090204-FP
TCMT110202-FP
TCMT110204-FP
TCMT16T304-FP
TCMT090202-FM
TCMT090204-FM
TCMT110202-FM
TCMT110204-FM
TCMT16T304-FM
TCMT110204-FV
TCMT16T304-FV
RE
(mm)
Coated
Cermet
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
FP
FV
0.4
Stainless Steel
Order Number
Finish Cutting
0.3
Steel
Shape
FM
0.2
Feed (mm/rev)
Coated
Finish Cutting
POSI
7
0.2
0.4
a a
a a
0.2
a a
0.4
0.4
a a
a a
0.2
0.4
0.2
0.4
0.4
Applicable
Holder Page
Finish Cutting

Size
TURNING INSERTS
TC
TCMT 09 02 02- FP
Depth of Cut (mm)
60
TYPE INSERTS
WITH HOLE
C027
E028
C027
E028
0.4
0.4
a a
a a
C027
E028
Finish Cutting
AZ
Medium Cutting
Finish Cutting
R/L-F
Finish Cutting
LP
Light Cutting
TCGT110202-AZ
TCGT110204-AZ
TCGT110208-AZ
TCGT16T302-AZ
TCGT16T304-AZ
TCGT16T308-AZ
TCGT0601V3L-F
TCGT060101L-F
TCGT060102R-F
TCGT060102L-F
TCGT060104R-F
TCGT060104L-F
TCMT090204-LP
TCMT090208-LP
TCMT110204-LP
TCMT110208-LP
TCMT16T304-LP
TCMT16T308-LP
0.2
0.4
0.8
C027
0.2
E028
0.4
0.8
0.03
0.1
0.2
0.2
0.4
0.4
E017
0.4
0.8
a a
a a
0.4
a a
C027
0.8
a a
E028
0.4
0.8
a a
a a
CHIP BREAKERS
GRADES
IDENTIFICATION
A054
A030
A002
A141
TC
TYPE INSERTS
WITH HOLE
Mild Steel
4
FP
LP
2
MP
1
0.1
0.2
0.3
Feed (mm/rev)
0.4
Light Cutting
Medium Cutting

4
4
FP
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
LM
2
MM
1
0
0.4
FM
0.1
0.2
0.3
Feed (mm/rev)
Work
Material
MK
2
1
0
0.4
0.1
0.3
: Stable Cutting
0.4
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
RE
(mm)
Coated
Cermet
Cermet
Shape
Order Number
LM
TCMT090204-LM
TCMT090208-LM
TCMT110204-LM
TCMT110208-LM
TCMT16T304-LM
TCMT16T308-LM
TCMT110204-MK
TCMT16T304-MK
TCMT16T308-MK
TCMT16T312-MK
0.4
0.8
a a
a a
0.4
a a
C027
0.8
a a
E028
0.4
0.8
a a
a a
TCMT090204-MP
TCMT090208-MP
TCMT110204-MP
TCMT110208-MP
TCMT130304-MP
TCMT16T304-MP
TCMT16T308-MP
TCMT16T312-MP
TCMT090204-MM
TCMT090208-MM
TCMT110204-MM
TCMT110208-MM
TCMT130304-MM
TCMT16T304-MM
TCMT16T308-MM
TCMT16T312-MM
TCMT080204
TCMT090204
TCMT110202
TCMT110204
TCMT110208
0.4
0.8
a a
a a
0.4
a a
0.8
a a
C027
0.4
a a
E028
0.4
a a
0.8
1.2
a a
a a
Light Cutting
NEW
0.2
Feed (mm/rev)
P
M
K
N
S
Applicable
Holder Page
WITH
HOLE

Size
Depth of Cut (mm)
Finish Cutting
TCMT 09 02 04- LM
Depth of Cut (mm)
Depth of Cut (mm)
POSI
7
60
Depth of Cut (mm)
TURNING INSERTS
MK
0.4
0.4
a a
0.8
a a
1.2
a a
a a
C027
E028
Medium Cutting
MP
Medium Cutting
MM
Medium Cutting
Standard
Medium Cutting
A142

0.4
0.8
a a
a a
0.4
a a
0.8
a a
C027
0.4
a a
E028
0.4
a a
0.8
1.2
a a
a a
0.4
0.4
a [
0.2
a [
0.4
0.8
a a [
a a
a a
a a a a
a a a a
a a a a
C027
E028
a
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Standard
Order Number
TCMT130302
TCMT130304
TCMT16T304
TCMT16T308
Medium Cutting
TCMT16T312
TCMW110204
Flat Top
TCMW130304
TCMW16T304
TCMW16T308
NEW TCMW16T312
RE
(mm)
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
: Unstable Cutting
Applicable
Holder Page
Work
Material
P
M
K
N
S
: General Cutting
TURNING INSERTS
: Stable Cutting
POSI
7
WITH
HOLE
0.2
0.4
0.4
a a [
a a a a
0.8
1.2
a a [
a a a a
a a a
a a
C027
E028
0.4
0.4
a a a a
0.4
a a a a
0.8
1.2
a a a a
a
a
C027
E028
a a
CHIP BREAKERS
GRADES
IDENTIFICATION
A054
A030
A002
A143
TE
TYPE INSERTS
WITH HOLE

N
16 03 02 R
Size
R/L
Medium Cutting
Aluminium Alloy
4
R/L
3
2
1
0
0.1
0.2
0.3
Feed (mm/rev)
WITH
HOLE
0.4
Work
Material
P
M
K
N
S
: Unstable Cutting
Cast Iron
Non-ferrous Metal
R/L
TEGX160302R
TEGX160302L
TEGX160304R
TEGX160304L

RE
(mm)
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Order Number
: General Cutting
Stainless Steel
Shape
Medium Cutting
: Stable Cutting
Steel
Coated
A144
TEGX
0.2
0.2
0.4
0.4
Applicable
Holder Page
POSI
20
60
Depth of Cut (mm)
TURNING INSERTS
C033
E042

CHIP BREAKERS
A066
TP
Mild Steel
FV
2
MV
SV
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
Light Cutting
Medium Cutting
Depth of Cut (mm)
Depth of Cut (mm)
Depth of Cut (mm)
3
FV
2
MV
SV
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
3
FV
2
MV
SV
Work
Material
POSI
11
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
P
M
K
N
S
: Stable Cutting
Cast Iron
Non-ferrous Metal
FV
TPMH080202-FV
TPMH080204-FV
TPMH090202-FV
TPMH090204-FV
TPMH110302-FV
TPMH110304-FV
TPMH110308-FV
TPMH160302-FV
TPMH160304-FV
TPMH160308-FV
TPGH080202R-FS
TPGH080202L-FS
TPGH080204R-FS
TPGH080204L-FS
TPGH090202R-FS
TPGH090202L-FS
TPGH090204R-FS
TPGH090204L-FS
TPGH110302R-FS
TPGH110302L-FS
TPGH110304R-FS
TPGH110304L-FS
TPGH160304R-FS
TPGH160304L-FS
TPGH160308R-FS
TPGH160308L-FS
RE
(mm)
Coated
Cermet
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Order Number
Finish Cutting
: Unstable Cutting
Stainless Steel
Shape
R/L-FS
: General Cutting
WITH
HOLE
Steel
Coated
Finish Cutting

Size
0.2
0.4
a a a
a a a
0.2
a a a
0.4
a a a
0.2
a a a
0.4
a a a
0.8
a a a
0.2
a a a
0.4
0.8
a a a
a a a
0.2
0.2
0.4
0.4
0.2
0.2
0.4
0.4
0.2
0.2
0.4
0.4
0.4
0.4
0.8
0.8
Applicable
Holder Page
Finish Cutting
TPMH 08 02 02- FV
TURNING INSERTS
60
TYPE INSERTS
WITH HOLE
E007
a
a a
a
a
a a
a
a
a a
a
a
a a
a
a
a a
E007
a
a
a a
a
a
a
a
CHIP BREAKERS
GRADES
IDENTIFICATION
A062
A030
A002
A145
TP
TYPE INSERTS
WITH HOLE
Finish Cutting
Mild Steel
3
FV
2
MV
SV
1
0
0.1
0.2
0.3
Feed (mm/rev)
WITH
HOLE
0.4
Light Cutting
Medium Cutting
FV
2
MV
SV
1
0.1
0.2
0.3
Feed (mm/rev)
3
FV
2
1
0
0.4
MV
SV
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S
: Stable Cutting
R/L
Finish Cutting
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Order Number
RE
(mm)
TPGX080202R
TPGX080202L
TPGX080204R
TPGX080204L
TPGX090202R
TPGX090202L
TPGX090204R
TPGX090204L
TPGX090208R
TPGX090208L
TPGX110302L
TPGX110304R
TPGX110304L
TPGX110308R
TPGX110308L
TPMX090204L
TPMX110304L
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
R/L
08 02 02 R
Size
Depth of Cut (mm)
TPGX
0.2
0.2
0.4
0.4
a a
0.2
0.2
0.4
0.4
a a
Applicable
Holder Page
Depth of Cut (mm)
POSI
11
60
Depth of Cut (mm)
TURNING INSERTS
0.8
E025
0.8
0.2
0.4
a a
0.4
a a
0.8
0.8
a a
a a a
0.4
0.4
a
a
a
a
E025
Finish Cutting
SV
Light Cutting
Standard
TPMH080202-SV
TPMH080204-SV
TPMH090202-SV
TPMH090204-SV
TPMH110302-SV
TPMH110304-SV
TPMH110308-SV
TPMH160302-SV
TPMH160304-SV
TPMH160308-SV
TPMX110304
TPMX110308
0.2
0.4
[ a
a a a
[ a
a a a
0.2
[ a
a a a
0.4
[ a
a a a
0.2
[ a
a a a
0.4
[ a
a a a
0.8
[ a
a a a
0.2
[ a
a a a
0.4
0.8
[ a
a a a
[ a
a a a
0.4
0.8
E007
a a a
a a a
E025
Medium Cutting
A146

Stainless Steel
Cast Iron
Non-ferrous Metal
Order Number
MV
TPMH080202-MV
TPMH080204-MV
TPMH090202-MV
TPMH090204-MV
TPMH090208-MV
TPMH110302-MV
TPMH110304-MV
TPMH110308-MV
TPMH160304-MV
TPMH160308-MV
TPGX080202
TPGX080204
TPGX080208
TPGX090202
TPGX090204
TPGX090208
TPGX110302
TPGX110304
TPGX110308
TPGX160304
TPGX160308
RE
(mm)
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
Flat Top
: Unstable Cutting
Steel
Coated
Medium Cutting
: General Cutting
Applicable
Holder Page
Work
Material
P
M
K
N
S
: Stable Cutting
TURNING INSERTS
POSI
11
WITH
HOLE
0.2
0.4
[ a
a a a
[ a
a a a a
0.2
[ a
a a a
0.4
[ a
a a a a
0.8
a a
0.2
[ a
a a a a
0.4
[ a
a a a a
0.8
[ a
a a a a
0.4
0.8
[ a
a a a a
[ a
a a a a
E007
0.2
0.4
a a a
0.8
0.4
a a
0.8
a a
0.2
0.2
E025
0.4
a a a
a a a
0.8
a a
a a a
0.4
0.8
CHIP BREAKERS
GRADES
IDENTIFICATION
M006
A062
A030
A002
A147
Finish Cutting
Mild Steel
4
FP
LP
2
MP
1
0.1
0.2
0.3
Feed (mm/rev)
0.4
Medium Cutting
FP
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
FM
LM
2
MM
1
0
0.4
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S

4
3
MK
2
1
0
0.1
0.2
0.3
0.4
Feed (mm/rev)
: Stable Cutting
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
RE
(mm)
Coated
Cermet
Cermet
Shape
Order Number
FP
VBMT110302-FP
VBMT110304-FP
VBMT110308-FP
VBMT160404-FP
VBMT160408-FP
VBMT110302-FM
VBMT110304-FM
VBMT110308-FM
VBMT160404-FM
VBMT160408-FM
VBMT110304-FV
VBMT110308-FV
VBMT160404-FV
VBMT160408-FV
0.2
0.4
a a
a a
0.8
a a
E011
0.4
0.8
a a
E012
a a
VBGT110302R-F
VBGT110302L-F
VBGT110304R-F
VBGT110304L-F
VBGT160402R-F
VBGT160402L-F
VBGT160404R-F
VBGT160404L-F
VBMT110304-LP
VBMT110308-LP
VBMT160404-LP
VBMT160408-LP
0.2
0.2
a a
a a
0.4
0.4
0.2
0.2
0.4
0.4
VBMT110304-LM
VBMT110308-LM
VBMT160404-LM
VBMT160408-LM
0.4
0.8
a a
a a
0.4
a a
E011
0.8
a a
E012
Finish Cutting
FM
Finish Cutting
FV
D010
D011
H013
0.2
0.4
0.8
E011
0.4
0.8
E012
D010
D011
H013
0.4
0.8
a a
a a
0.4
a a
E011
0.8
a a
E012
D010
D011
H013
Finish Cutting
R/L-F
Finish Cutting
LP
LM
D011
E011
E012
H013
a a
a a
0.4
a a
E011
0.8
a a
E012
D010
D011
H013
D010
D011
H013
Light Cutting

D010
0.4
0.8
Light Cutting
A148
Applicable
Holder Page
WITH
HOLE
Light Cutting
Depth of Cut (mm)
TYPE INSERTS VBMT 11 03 02- FP

WITH HOLE
Depth of Cut (mm)
Depth of Cut (mm)
POSI
5
VB
35
Depth of Cut (mm)
TURNING INSERTS
: General Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
RE
(mm)
Coated
Cermet
Cermet
POSI
5
D010
WITH
HOLE
Shape
Order Number
SV
VBMT110304-SV
VBMT110308-SV
VBMT160404-SV
VBMT160408-SV
0.4
0.8
0.4
E011
0.8
E012
VBMT160404-MK
VBMT160408-MK
0.4
0.8
D011
H013
Light Cutting
NEW
: Unstable Cutting
Applicable
Holder Page
Work
Material
P
M
K
N
S
: Stable Cutting
MK
TURNING INSERTS
a a
a a
E011
H013
Medium Cutting
MP
VBMT160404-MP
VBMT160408-MP
0.4
0.8
a a
a a
E011
H013
Medium Cutting
MM
VBMT160404-MM
VBMT160408-MM
0.4
0.8
a a
a a
E011
H013
Medium Cutting
Standard
VBMT160404
VBMT160408
0.4
0.8
a
a
E011
H013
Medium Cutting
MV
VBMT110304-MV
VBMT110308-MV
VBMT160404-MV
VBMT160408-MV
0.4
0.8
[ a
a a a a
[ a
a a a a
0.4
[ a
a a a a
E011
E012
0.8
[ a
a a a a
D010
D011
H013
Medium Cutting
CHIP BREAKERS
GRADES
IDENTIFICATION
A052
A030
A002
A149
VB
Mild Steel
FP
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
WITH
HOLE
0.4
FP
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
FM
LM
2
MM
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S

4
Depth of Cut (mm)
POSI
5
Medium Cutting
Depth of Cut (mm)
Depth of Cut (mm)
Light Cutting
3
MK
2
1
0
0.1
0.3
: Stable Cutting
0.4
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Order Number
R/L-SR VBET1103V3R-SR
VBET1103V3L-SR
VBET110301R-SR
VBET110301L-SR
VBET110302R-SR
VBET110302L-SR
VBET110304R-SR
Medium Cutting VBET110304L-SR
R/L-SN VBET110300R-SN
VBET110300L-SN
VBET1103V3R-SN
VBET1103V3L-SN
VBET110301R-SN
VBET110301L-SN
VBET110302R-SN
VBET110302L-SN
VBET110304R-SN
Medium Cutting VBET110304L-SN
R/LW-SN VBET1103V3RW-SN
VBET1103V3LW-SN
RE
(mm)
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
0.2
Feed (mm/rev)
0.03
0.03
0.1
0.1
0.2
0.2
0.4
0.4
0
0
0.03
0.03
0.1
0.1
0.2
0.2
0.4
0.4
0.03
0.03
Applicable
Holder Page
Finish Cutting
Depth of Cut (mm)
TURNING INSERTS
35
TYPE INSERTS VBMW 16 04 08

Size Thickness Corner Radius
WITH HOLE
D010
D011
E011
E012
D010
D011
E011
E012
D010
D011
E011
E012
Medium Cutting
(Wiper)
NEW
Flat Top
VBMW160408
0.8
a a
E011
E012
* Please refer to A028 before using the R/LW-SN breaker (wiper insert).

a
A150

CHIP BREAKERS
A052
Mild Steel
FP
LP
2
MP
1
0.1
0.2
0.3
Feed (mm/rev)
0.4
FP
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
FM
LM
2
MM
1
0
0.4
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S

4
3
MK
2
POSI
7
1
0
0.1
0.2
0.3
0.4
Feed (mm/rev)
: Stable Cutting
: General Cutting
: Unstable Cutting
WITH
HOLE
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
RE
(mm)
Coated
Cermet
Cermet
Shape
Order Number
FP
VCMT110302-FP
VCMT110304-FP
VCMT160404-FP
VCMT160408-FP
0.2
0.4
a a
a a
0.4
a a
0.8
a a
VCMT110302-FM
VCMT110304-FM
VCMT160404-FM
VCMT160408-FM
0.2
0.4
0.4
0.8
VCMT080202-FV
VCMT080204-FV
VCMT160404-FV
VCMT160408-FV
0.2
0.4
a a a
a a a
0.4
a [
a a
0.8
a [
a a
VCGT160404-AZ
VCGT160408-AZ
VCGT160412-AZ
0.4
0.8
1.2
Applicable
Holder Page
Depth of Cut (mm)
Medium Cutting
Depth of Cut (mm)
Depth of Cut (mm)
Light Cutting
Depth of Cut (mm)
Finish Cutting
TURNING INSERTS
VC
35
TYPE INSERTS VCMT 11 03 02- FP

WITH HOLE
C028
C029
E032
E033
Finish Cutting
FM
C028
C029
E032
E033
Finish Cutting
FV
C028
C029
E011
E012
E032
E033
Finish Cutting
AZ
C028
C029
E032
E033
Finish Cutting
R/L-F
VCGT080202R-F
VCGT080202L-F
VCGT080204R-F
VCGT080204L-F
0.2
0.2
0.4
0.4
VCMT110304-LP
VCMT110308-LP
VCMT160404-LP
VCMT160408-LP
0.4
0.8
a a
a a
0.4
a a
0.8
a a
VCMT110304-LM
VCMT110308-LM
VCMT160404-LM
VCMT160408-LM
0.4
0.8
a a
a a
0.4
a a
0.8
a a
E011
E012
Finish Cutting
LP
C028
C029
E032
E033
Light Cutting
LM
C028
C029
E032
E033
Light Cutting
CHIP BREAKERS
GRADES
IDENTIFICATION
A054
A030
A002
A151
Finish Cutting
Mild Steel
4
FP
LP
2
MP
1
0.1
0.2
0.3
Feed (mm/rev)
0.4
Medium Cutting

4
4
FP
LP
2
MP
1
0
0.1
0.2
0.3
Feed (mm/rev)
LM
2
MM
1
0
0.4
FM
0.1
0.2
0.3
Feed (mm/rev)
Work
Material
MK
2
1
0
0.4
0.1
0.2
0.3
0.4
Feed (mm/rev)
: Stable Cutting
P
M
K
N
S
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Order Number
RE
(mm)
SV
VCMT080202-SV
VCMT080204-SV
0.2
0.4
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
Coated
Cermet
Cermet
a a
a a
Applicable
Holder Page
WITH
HOLE
Light Cutting
Depth of Cut (mm)
TYPE INSERTS VCMT 08 02 02- SV

WITH HOLE
Depth of Cut (mm)
Depth of Cut (mm)
POSI
7
VC
35
Depth of Cut (mm)
TURNING INSERTS
E011
E012
Light Cutting
NEW
MK
VCMT160404-MK
VCMT160408-MK
0.4
0.8
a a
C028
a a
C029
E032
E033
Medium Cutting
MP
VCMT160404-MP
VCMT160408-MP
VCMT160412-MP
0.4
0.8
a a
a a
1.2
a a
C028
C029
E032
E033
Medium Cutting
MM
VCMT160404-MM
VCMT160408-MM
VCMT160412-MM
0.4
0.8
a a
a a
1.2
a a
C028
C029
E032
E033
Medium Cutting
Standard
VCMT110304
VCMT160404
VCMT160408
VCMT160412
0.4
0.4
a [
a a a a
a a [
a a a a
0.8
a a [
a a a a
1.2
a [
VCMT080202-MV
VCMT080204-MV
0.2
0.4
[ a
a a a a
[ a
a a a a
C028
C029
E032
a a
E033
Medium Cutting
MV
C028
C029
E032
E033
Medium Cutting
Flat Top
VCMW110304
VCMW160404
VCMW160408
0.4
0.4
a a a a
0.8
a a a a
C028
C029
E032
E033

a
A152

CHIP BREAKERS
A054
VD

N
Medium Cutting
Aluminium Alloy
3
2
R/L
POSI
15
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Shape
Order Number
R/L
VDGX160302R
VDGX160302L
VDGX160304R
VDGX160304L
RE
(mm)
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Coated
Medium Cutting
(For Aluminium)
: Stable Cutting
WITH
HOLE
0.2
0.2
0.4
0.4
Applicable
Holder Page
Depth of Cut (mm)
TURNING INSERTS
35
TYPE INSERTS VDGX 16 03 02 R

R/L
Size Thickness Corner Radius
WITH HOLE
CHIP BREAKERS
GRADES
IDENTIFICATION
C034
A066
A030
A002
A153
Finish Cutting
Mild Steel
3
SMG
2
1
3
SMG
2
1
0.2
0.3
Feed (mm/rev)
WITH
HOLE
3
SMG
2
1
SRF
SRF
0.1
Medium Cutting
Depth of Cut (mm)
TYPE INSERTS VPGT 08 02 01 SMG

WITH HOLE
0.4
0.1
0.2
SRF
0.3
Feed (mm/rev)
0.4
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S
: Stable Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Order Number
R/L-SRF VPET080201R-SRF
VPET080201L-SRF
VPET080202R-SRF
VPET080202L-SRF
VPET1103V3R-SRF
VPET1103V3L-SRF
VPET110301R-SRF
VPET110301L-SRF
VPET110302R-SRF
Finish Cutting VPET110302L-SRF
SMG VPGT080201M-SMG
VPGT080202M-SMG
VPGT110301M-SMG
VPGT110302M-SMG
RE
(mm)
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
: General Cutting
Applicable
Holder Page
Depth of Cut (mm)
POSI
11
VP
35
Depth of Cut (mm)
TURNING INSERTS
0.1
0.1
0.2
0.2
0.03
D010
0.03
D011
0.1
0.1
0.2
0.2
0.1
0.2
0.1
0.2
D010
D011
Medium Cutting

a
A154

CHIP BREAKERS
A062
WB
Mild Steel
MV
2
1
0
R/L-F
0.1
0.2
0.3
Feed (mm/rev)
0.4
3
MV
2
1
0
Medium Cutting
Depth of Cut (mm)
R/L-F
0.1
0.2
0.3
Feed (mm/rev)
3
MV
2
1
0
0.4
Work
Material
POSI
5
R/L-F
0.1
0.2
0.3
Feed (mm/rev)
0.4
P
M
K
N
S
Depth of Cut (mm)
Depth of Cut (mm)
: Stable Cutting
: Unstable Cutting
Stainless Steel
Cast Iron
Non-ferrous Metal
RE
(mm)
Coated
Cermet
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Order Number
WBGT0201V3L-F
WBGT020101L-F
WBGT020102L-F
WBGT020104L-F
WBGTL302V3L-F
WBGTL30201L-F
WBGTL30202R-F
WBGTL30202L-F
WBGTL30204R-F
Finish Cutting WBGTL30204L-F
R/L-MV WBMTL30202R-MV
WBMTL30202L-MV
WBMTL30204R-MV
WBMTL30204L-MV
R/L-F
: General Cutting
WITH
HOLE
Steel
Coated
Shape
Thickness Corner Radius R/L Chip Breaker

Size
Applicable
Holder Page
Finish Cutting
WBGT 02 01 V3 L F
TURNING INSERTS
80
TYPE INSERTS
WITH HOLE
0.03
0.1
0.2
0.4
0.03
E010
0.1
E016
0.2
0.2
0.4
0.4
0.2
0.2
a a a
a
a
a a a
0.4
a a a
0.4
a a a
E010
E016
Medium Cutting
CHIP BREAKERS
GRADES
IDENTIFICATION
A052
A030
A002
A155
WC
TYPE INSERTS
WITH HOLE
2
1
0
0.1
0.2
0.3
Feed (mm/rev)
WITH
HOLE
0.4
3
Standard
2
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
3
Standard
2
1
0
0.1
0.2
0.3
Feed (mm/rev)
Work
Material
Non-ferrous Metal
WCGT020102R
WCGT020102L
WCGT020104R
WCGT020104L
WCGTL30202L
WCGTL30204L
WCMT020102
WCMT020104
WCMTL30202
WCMTL30204
WCMT040202
WCMT040204
WCMT040208
WCMT06T304
WCMT06T308

a
RE
(mm)
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
R/L
Medium Cutting
: Unstable Cutting
Cast Iron
Order Number
Standard
: General Cutting
Stainless Steel
Shape
Finish Cutting
: Stable Cutting
Steel
Coated
A156
0.4
P
M
K
N
S
Depth of Cut (mm)
Standard
R/L
Size
Medium Cutting
Mild Steel
4
WCGT 02 01 02 R
0.2
0.2
0.4
0.4
0.2
0.4
Applicable
Holder Page
Depth of Cut (mm)
POSI
7
80
Depth of Cut (mm)
TURNING INSERTS
E027
0.2
0.4
a [
a a a a
a [
a a a a
0.2
a a a a
0.4
a a a a
0.2
a [
a a a a
0.4
a [
a a a a
0.8
0.4
0.8
a [
a a a a
a [
a a a a
E027

CHIP BREAKERS
A054
WP
Mild Steel
MV
2
1
0
R/L-FS
0.1
0.2
0.3
Feed (mm/rev)
0.4
3
MV
2
1
0
Medium Cutting
R/L-FS
0.1
0.2
0.3
Feed (mm/rev)
3
MV
2
1
0
0.4
Work
Material
POSI
11
R/L-FS
0.1
0.2
0.3
Feed (mm/rev)
0.4
P
M
K
N
S
Depth of Cut (mm)

Depth of Cut (mm)
Depth of Cut (mm)
Size
: Stable Cutting
: General Cutting
: Unstable Cutting
WITH
HOLE
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
RE
(mm)
Cermet
Shape
Order Number
R/L-FS
WPGT040204R-FS
WPGT040204L-FS
WPGT060304R-FS
WPGT060304L-FS
0.4
0.4
0.4
0.4
WPMT040202-MV
WPMT040204-MV
WPMT060304-MV
WPMT060308-MV
0.2
0.4
[ a
a a a
[ a
a a a
0.4
[ a
a a a
0.8
[ a
a a a
Applicable
Holder Page
Finish Cutting
WPMT 04 02 02 MV
TURNING INSERTS
80
TYPE INSERTS
WITH HOLE
E010
Finish Cutting
MV
E010
a
Medium Cutting
CHIP BREAKERS
GRADES
IDENTIFICATION
A062
A030
A002
A157

P
TYPE INSERTS XCMT 15 03 02- SVX

WITH HOLE
Light Cutting
Mild Steel
4
Depth of Cut (mm)
3
2
1
SVX
0.1
0.2
0.3
Feed (mm/rev)
WITH
HOLE
0.4
3
2
1
SVX
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S
: Stable Cutting
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Order Number
SVX
XCMT150302-SVX
XCMT150304-SVX
XCMT150308-SVX
RE
(mm)
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
Cermet
0.2
0.4
0.8
Applicable
Holder Page
POSI
7
XC
25
Depth of Cut (mm)
TURNING INSERTS
C030
Light Cutting

a
A158

CHIP BREAKERS
A054
For Special Use

(For TL Holder)
: General Cutting
: Unstable Cutting
Stainless Steel
Cast Iron
Non-ferrous Metal
Order Number
RTG05A
RTG06A
RTG07A
RTG08A
RTG10A
RE
(mm)
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Coated
Shape
: Stable Cutting
Steel
GRADES
IDENTIFICATION
Applicable
Holder Page
Work
Material
P
M
K
N
S
TURNING INSERTS
RTG
TYPE INSERTS
WITHOUT HOLE
POSI
6
WITHOUT
HOLE
C035
A030
A002
A159
SP
TYPE INSERTS
WITHOUT HOLE

P
SPGR
09 03 04 R
Size
R/L
Medium Cutting
Mild Steel
4
Depth of Cut (mm)
3
Standard
2
1
0
0.1
0.2
0.3
Feed (mm/rev)
WITHOUT
HOLE
0.4
3
Standard
2
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S
: Stable Cutting
: General Cutting
: Unstable Cutting
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Coated
Order Number
RE
(mm)
SPGR090304R
0.4
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
Cermet
Applicable
Holder Page
POSI
11
90
Depth of Cut (mm)
TURNING INSERTS
Finish Cutting
Standard
SPMR090304
SPMR090308
SPMR120304
SPMR120308
0.4
0.8
a [
a a a
a [
a a a
0.4
a [
a a a
0.8
a [
a a a
SPMN090304
SPMN090308
SPMN120304
SPMN120308
SPMN120312
SPMN120408
SPMN120412
SPMN150408
SPMN150412
SPMN190404
SPMN190408
SPMN190412
SPGN090304
SPGN090308
SPGN120304
SPGN120308
SPGN120312
SPGN120404
SPGN120408
SPGN150404
SPGN150408
0.4
0.8
0.4
0.8
a a
1.2
a [
Light to Medium Cutting
Flat Top
Flat Top

a
A160
0.8
1.2
0.8
1.2
0.4
0.8
1.2
a
a
0.4
0.8
0.4
0.8
a a
1.2
0.4
0.8
0.4
0.8

CHIP BREAKERS
A068
TC

P

Medium Cutting
Depth of Cut (mm)
3
2
Standard
1
0.1
0.2
0.3
Feed (mm/rev)
0.4
3
2
Standard
POSI
7
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S
: Stable Cutting
: General Cutting
: Unstable Cutting
WITHOUT
HOLE
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Shape
Order Number
RE
(mm)
Flat Top
TCGN060104
TCGN090204
0.4
0.4
Cermet
Coated
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Coated
Applicable
Holder Page
Depth of Cut (mm)
Size
Mild Steel
4
TCGN 06 01 04
TURNING INSERTS
60
TYPE INSERTS
WITHOUT HOLE
a
a
CHIP BREAKERS
GRADES
IDENTIFICATION
A068
A030
A002
A161
TP
TYPE INSERTS
WITHOUT HOLE

P
Finish Cutting
TPGR
11 03 04 R
R/L
Size
Medium Cutting
Mild Steel
4
Depth of Cut (mm)
3
R/L
2
Standard
1
0
0.1
0.2
0.3
Feed (mm/rev)
WITHOUT
HOLE
0.4
3
R/L
2
Standard
1
0
0.1
0.2
0.3
Feed (mm/rev)
0.4
Work
Material
P
M
K
N
S
: Stable Cutting
Stainless Steel
Cast Iron
Non-ferrous Metal
Order Number
R/L
TPGR110304R
TPGR110304L
TPGR160304R
TPGR160304L
TPGR160308R
TPGR160308L
TPMR090202
TPMR090204
TPMR090208
TPMR110302
TPMR110304
TPMR110308
TPMR160304
TPMR160308
TPMR160312
TPMN110304
TPMN110308
TPMN160304
TPMN160308
TPMN160312
TPMN160320
TPMN220404
TPMN220408
TPMN220412
TPGN110302
TPGN110304
TPGN110308
TPGN160302
TPGN160304
TPGN160308
TPGN160312
TPGN160316
TPGN160408
TPGN220404
TPGN220408
Light to
Medium Cutting
Flat Top
Flat Top
RE
(mm)
Coated
Cermet
Cermet
Carbide
UE6105
UE6110
UE6020
N
MC6015 EW
MC6025
UH6400
MC7025
MP7035
US7020
US735
US905
N
MC5005 EW
N
MC5015 EW
UC5105
UC5115
VP05RT
VP10RT
VP15TF
UP20M
NX2525
NX3035
MP3025
AP25N
VP25N
VP45N
UTi20T
HTi05T
HTi10
RT9010
Shape
Standard
0.4
0.4
a
a
0.4
0.4
0.8
0.8
a
a
0.2
0.4
a a
0.8
0.2
a a a
0.4
a a
a a a
0.8
a a
a a a
0.4
a a
a a a
0.8
1.2
a a
a a a
0.4
0.8
a a a a
a a
a a a a
0.4
a a a a
a a a
0.8
a a a a
a a a
a a a
1.2
a a a a
E026
a a
2.0
a
0.8
1.2
a a
a a
0.2
0.4
a
a
a a a
0.2
0.4
a a
a a a
0.8
a a
a a a
1.2
A162
E026
1.6
0.8
0.4
0.8
E026
0.4
0.8
E026
a a a
a
a
CHIP BREAKERS

: Unstable Cutting
Steel
Coated
Finish Cutting
: General Cutting
Applicable
Holder Page
POSI
11
60
Depth of Cut (mm)
TURNING INSERTS
GRADES
IDENTIFICATION
A068
A030
A002
Memo
A163

OF CBN&PCD TURNING INSERTS
z Organized according to turning insert shape.
x Inserts are arranged in order of :
Negative inserts (with hole|without hole)
Positive inserts (with hole|without hole)
FIGURE SHOWING THE INSERT GEOMETRY
GRADE APPLICATION RECOMMENDED

FOR EACH WORK MATERIAL
IC : Diameter of Inscribed Circle S : Thickness

RE : Corner Radius D1 : Diameter of Hole
Dimensions are detailed in the "Dimensions" column.
cutting conditions suitable for each type of work material

is shown as a general guide to select the grade.
: Stable Cutting : General Cutting : Unstable Cutting
STOCK STATUS
INDICATION OF
NEGATIVE/POSITIVE
TYPE
TITLE OF PRODUCT
ACCORDING TO THE
INSERT TYPE
SHAPE &
ANGLE MARK
PRODUCT SECTION
INSERT NUMBER
INSERT GRADES
INSERT DIMENSIONS
CBN TURNING INSERTS [NEGATIVE]
TYPE INSERTS
WITH HOLE
Coated
CBN
Shape
NEW PETIT CUT
NEG
WITH
HOLE
Order Number
NEW PETIT CUT
Solid
CBN
RE
D1
12.7 4.76
0.4
5.16
NP-CNGA120408GA4
NP-CNGA120412GA4
Geometry
H
K
S
Hardened Materials
: Stable Cutting
Coated
CBN
NEW PETIT CUT
Order Number
NP-CNGA120404GA2
Solid
CBN
CBN
RE
D1
12.7 4.76
0.4
5.16
12.7 4.76
0.8
5.16
12.7 4.76
1.2
5.16
12.7 4.76
0.2
5.16
12.7 4.76
0.8
5.16
NP-CNGA120408GA2
12.7 4.76
1.2
5.16
NP-CNGA120412GA2
12.7 4.76
0.4
5.16
NP-CNGA120402GS2
NP-CNGA120408GN4
12.7 4.76
0.8
5.16
NP-CNGA120404GS2
a a
a a
12.7 4.76
0.4
5.16
NP-CNGA120412GN4
12.7 4.76
1.2
5.16
NP-CNGA120408GS2
a a
a a
12.7 4.76
0.8
5.16
12.7 4.76
0.4
5.16
NP-CNGA120412GS2
a a
a a
12.7 4.76
1.2
5.16
12.7 4.76
0.4
5.16
12.7 4.76
0.8
5.16
12.7 4.76
1.2
5.16
12.7 4.76
0.2
5.16
C008
C009
E013
E036
E040
H006
008
NP-CNGA120404GN2
12.7 4.76
0.8
5.16
NP-CNGA120412GS4
12.7 4.76
1.2
5.16
NP-CNGA120404FS4
a a
12.7 4.76
0.4
5.16
NP-CNGA120408FS4
a a
12.7 4.76
0.8
5.16
NP-CNGA120402FS2
NP-CNGA120412FS4
a a
12.7 4.76
1.2
5.16
NP-CNGA120404FS2
a a
12.7 4.76
0.4
5.16
NP-CNGA120404TA4
12.7 4.76
0.4
5.16
NP-CNGA120408FS2
a a
12.7 4.76
0.8
5.16
NP-CNGA120408TA4
12.7 4.76
0.8
5.16
NP-CNGA120412FS2
a a
12.7 4.76
1.2
5.16
NP-CNGA120412TA4
12.7 4.76
0.4
5.16
12.7 4.76
NP-CNGA120408GN2
NP-CNGA120412GN2
12.7 4.76
1.2
5.16
NP-CNGA120404TA2
NP-CNGA120404TS4
12.7 4.76
0.4
5.16
NP-CNGA120408TA2
0.8
5.16
NP-CNGA120408TS4
12.7 4.76
0.8
5.16
NP-CNGA120412TA2
12.7 4.76
1.2
5.16
NP-CNGA120412TS4
12.7 4.76
1.2
5.16
NP-CNGA120404TS2
12.7 4.76
0.4
5.16
NP-CNGA120408TS2
12.7 4.76
0.8
5.16
NP-CNGA120412TS2
12.7 4.76
1.2
5.16
NP-CNGA120404GAWS4
12.7 4.76
0.4
5.16
NP-CNGA120408GAWS4
12.7 4.76
0.8
5.16
NP-CNGA120412GAWS4
12.7 4.76
1.2
5.16
NP-CNGA120404GSWS4
12.7 4.76
0.4
5.16
NP-CNGA120408GSWS4
12.7 4.76
0.8
5.16
NP-CNGA120412GSWS4
12.7 4.76
1.2
5.16
BF-CNGG120404TA4
12.7 4.76
0.4
5.16
BF-CNGG120408TA4
12.7 4.76
0.8
5.16
BF-CNGG120412TA4
12.7 4.76
1.2
5.16
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
NP-CNGA120404G2
12.7 4.76
0.4
5.16
NP-CNGA120408G2
12.7 4.76
0.8
5.16
NP-CNGA120412G2
12.7 4.76
1.2
5.16
NP-CNGA120404T2
12.7 4.76
0.4
5.16
NP-CNGA120408T2
12.7 4.76
0.8
5.16
NP-CNGA120412T2
12.7 4.76
1.2
5.16
12.7 4.76
0.4
5.16
TNP-CNGA120408G2
12.7 4.76
0.8
5.16
TNP-CNGA120412G2
12.7 4.76
1.2
5.16
TNP-CNGA120404T2
12.7 4.76
0.4
5.16
NEW PETIT CUT TNP-CNGA120404G2
Please refer to B014 before using the wiper insert.
TNP-CNGA120408T2
TNP-CNGA120412T2
*1
*
*
: Unstable Cutting
Dimensions (mm)
IC
NEW PETIT CUT NP-CNGA120404GAWS2

(With Wiper)
12.7 4.76
0.8
5.16
12.7 4.76
1.2
5.16
a a
12.7 4.76
0.4
5.16
NP-CNGA120408GAWS2
a a
12.7 4.76
0.8
5.16
NP-CNGA120412GAWS2
a a
12.7 4.76
1.2
5.16
NP-CNGA120404GSWS2
a a
12.7 4.76
0.4
5.16
NP-CNGA120408GSWS2
a a
12.7 4.76
0.8
5.16
NP-CNGA120412GSWS2
a a
12.7 4.76
1.2
5.16
Geometry
NEG
WITH
HOLE
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
1 Please refer to B014 before using the wiper insert.

2 The order number is for a 10-insert pack. Please specify order number, grade and quantity.

(1 insert in one case)
B022
: General Cutting
Honing (Last letter of order number) : Refer to page B011.
Sintered Alloy
Shape
CBN
Cast Iron
NP-CNGA120404GN4
(With Breaker)
Work
Material
: Unstable Cutting
Dimensions (mm)
IC
NP-CNGA120408GS4
CBN
NP-CNGA120404GA4
NP-CNGA120404GS4
NEW PETIT CUT

(With Wiper)
: General Cutting
Sintered Alloy
CBN TURNING INSERTS
: Stable Cutting
Applicable
Holder Page
Cast Iron
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CN
Hardened Materials
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN TURNING INSERTS
Work
Material
H
K
S
Applicable
Holder Page
80
CBN
GRADES
IDENTIFICATION
B004
B002
B023
PAGE REFERENCE

PHOTO OF INSERT
CHIP BREAKERS
GRADES
TECHNICAL DATA
indicates reference pages, on the right hand page of
PRODUCT NAME
APPLICABLE HOLDER PAGE

indicates reference pages for details of applicable holders.

zinsert number and xgrade.
B000
TURNING TOOLS
CBN & PCD INSERT STANDARDS

CBN & PCD INSERT GRADES
INDENTIFICATION .................................................... B002
CBN (CUBIC BORON NITRIDE) ............................... B004
PCD (SINTERED DIAMOND) .................................... B015
CLASSIFICATION OF CBN & PCD INSERTS .......... B016
STANDARD OF CBN TURNING INSERTS
STANDARD OF PCD TURNING INSERTS
CNppTYPE...RHOMBIC 80 .......... B022

DNppTYPE...RHOMBIC 55 .......... B025
SNppTYPE...SQUARE 90 ........... B028
TNppTYPE...TRIANGULAR 60 ..... B030
VNppTYPE...RHOMBIC 35 .......... B032
WNppTYPE...TRIGON 80 ............ B034

T NppTYPE...TRIANGULAR 60 ..... B056
VNppTYPE...RHOMBIC 35 .......... B057

RNppTYPE...ROUND ................. B036
TNppTYPE...TRIANGULAR 60 ..... B038
CCppTYPE...RHOMBIC 80 .......... B039

CPppTYPE...RHOMBIC 80 .......... B042
DCppTYPE...RHOMBIC 55 .......... B043
TCppTYPE...TRIANGULAR 60 ..... B045
TP ppTYPE...TRIANGULAR 60 ..... B046
VB ppTYPE...RHOMBIC 35 .......... B048
VC ppTYPE...RHOMBIC 35 .......... B049
WCppTYPE...TRIGON 80 ............ B049
CCppTYPE...RHOMBIC 80 .......... B059

CP ppTYPE...RHOMBIC 80 .......... B059
DCppTYPE...RHOMBIC 55 .......... B060
SP ppTYPE...SQUARE 90 ........... B060
TC ppTYPE...TRIANGULAR 60 ..... B061
VB ppTYPE...RHOMBIC 35 .......... B064
VC ppTYPE...RHOMBIC 35 .......... B064
WCppTYPE...TRIGON 80 ............ B065
WPppTYPE...TRIGON 80 ............ B065
DE ppTYPE...RHOMBIC 55 .......... B066
TE ppTYPE...TRIANGULAR 60 ..... B066
VD ppTYPE...RHOMBIC 35 .......... B067
SPppTYPE...SQUARE 90 ........... B051

TBppTYPE...TRIANGULAR 60 ..... B052
RTGTYPE................................. B050
GYTYPE ................................... B053
MGTRTYPE ............................. B054
S PppTYPE...SQUARE 90 ........... B068

T P ppTYPE...TRIANGULAR 60...... B068
B001
IDENTIFICATION
IC
Tolerance of
Nose Height
M (mm)
Symbol
G
M
IC
Tolerance of
Inscribed Circle
IC (mm)
Tolerance of
Thickness
S (mm)
e0.025
e0.025
e0.13
e0.08 e0.18
e0.05 e0.15
e0.13
mark is sintered.
Detail of M Class Insert Tolerance

a Tolerance of Nose Height M (mm)
80
55
35
6.35 e0.08 e0.08 e0.08 e0.11 e0.16
9.525 e0.08 e0.08 e0.08 e0.11 e0.16
12.70 e0.13 e0.13 e0.13 e0.15
10-inserts Package
T
No mark
1-insert Package
z Insert Case
a Tolerance of Inscribed Circle IC (mm)
With Breaker
BM
BF
With Breaker
NP
New Petit Cut
No mark
Standard Type
D.I.C.

Triangular Square Rhombic
80
55
35
e0.05 e0.05 e0.05 e0.05 e0.05
6.35
9.525 e0.05 e0.05 e0.05 e0.05 e0.05 e0.05
e0.08
12.70 e0.08 e0.08 e0.08 e0.08

b Tolerance Class
x Insert Geometry
T NP - C N G A
c
c Insert Shape
Symbol
B002
Insert Shape
Square
Triangular
Rhombic 80
Rhombic 55
Rhombic 35
Trigon
Round
v Normal Clearance
n Fixing and/or for Chip Breaker
Symbol Normal Clearance
Metric
Hole
Configuration
W With Hole Cylindrical Hole
15
20
11
Symbol
Hole
+
One Countersink
With Hole
(4060)
Chip
Breaker
Figure
No
One
Sided

+
One Countersink
With Hole
(7090)
One
Sided
No
One
Sided
No
Without
Hole
No
Special Design

is from the bottom of the insert
*Thickness
to the top of the cutting edge.
Diameter of
Inscribed Circle
(mm)
Thickness (mm)
S1
1.39
01
1.59
T0
1.79
02
2.38
T2
2.78
03
3.18
T3
3.97
04
4.76
Symbol
R
09
12
02
L3
03
04
05
06
08
3.97
4.76
5.56
6.35
7.94
9.525
12.70
Symbol
08
09
11
13
16
22
04
05
06
07
09
11
15
03
04
05
06
08
09
12
03
04
05
06
07
09
12
06
08
09
11
13
16
22
m Insert Size
11 Wiper
u
/ Application (Honing)
GA
GS
GN
G
WS
No mark
General Cutting
FA
FS
FN
F
Continuous Cutting
TA
TS
TN
T
Interrupted Cutting
02
0.2
04
0.4
08
0.8
12
1.2
16
1.6
. Insert Corner
Configuration
Honing
Corner Radius
(mm)
, Insert Thickness
12 04 04 G WS 2
Symbol
Symbol
11
u
12 Number of Teeth
u
J
12
u
R
13
u
13 Cutting Edge Angle

u
With Wiper
Without Wiper
93
No mark
Non Restriction
No mark
91
Please pay special attention

when using an indexable
insert.
Please refer to page B014 for
further information.
14
u
14 Cutting Direction
u
Figure
Hand Symbol
Right R
Left
Neutral N
Please refer to page B011

for further information.
B003
COATED CBN SERIES

BC8110 / BC8020 / MBC010 / MBC020
FEATURES
Application range
With the expansion of BC8110, Mitsubishi can offer 4 coated CBN

grades for machining of hardened steels. These 4 coated CBN
grades cover a wide range of applications.
400
To achieve longer tool life, Mitsubishi uses a unique

"Particle-activated Sintering Method", combined with increased
cutting edge strength. With high crater wear resistance CBN grades
and a wear resistant ceramic coatings, longer tool life and improved
machine efficiency are obtained.
MBC010
300
200
BC8110
BC8020
100
MBC020
Light
Continuous
Heavy
Light
Interrupted
Heavy
Cutting mode
BC8110
y Newly developed special ceramic coating
Prevention of welding
Peeling of the coating is
prevented by improving welding
resistance.
TiAlSiN Coating
y The newly developed Ultra Micro-particle Binder prevents sudden fracture

Dispersal of the newly developed Ultra Micro-particle Binder for sintered CBN
and Micro Grain CBN suppresses cracking to prevent sudden fracturing.
Cutting resistance
Forces dispersed in
a linear direction can
cause sudden fracturing.
Medium Grain
CBN
Improved wear and chipping

resistance.
CBN sintered body

Micro Grain
CBN
TiAlN Coating
Improved adhesion to the CBN
surface provides increased
peeling resistance.
Cutting resistance
Forces dispersed
radially help to prevent
sudden fracturing.
Binder
microparticles
BC8110
Conventional
Crack progression suppression graphic
BC8110 is constantly stable without any cutting edge chipping and abnormal damage of the coating.
Grade
Grade Features and Application
Coated CBN for continuous cutting
BC8110
Newly developed Ultra Micro-particle Binder is consistent with wear resistance and cutting edge strength. Ultra Micro-particle
Binder provides protection by means of dual-layer ceramic coating film based on special CBN and TiAISiN + TiAIN. As a
result, it exhibits excellent wear resistance, high coating adhesive strength and performs long-term stable cutting.
High efficiency coated CBN
BC8020
Increased cutting edge strength and high crater wear resistant CBN grade in
combination with a highly wear resistant TiAlN coating, results in longer tool life
and improved machining efficiency under heavy duty or interrupting cutting.
Coated CBN for High Speed Continuous Cutting
MBC010
MBC010 makes the best use of special ceramic binder structure, actualizing
high wear resistance. High wear resistance enables continuous machining at
high speed of over 300m/min.
Coated CBN for general cutting
MBC020
B004
Uses a CBN substrate that has high cutting edge toughness. The TiAlN based
coating delivers superb wear resistance. It covers a wide range of applications
from continuous to light interrupted cutting.
Main
Component
Coating
Layer
CBN (Medium Grain)

TiN
Al2O3
TiAlSiN
TiAlN
Dual-layer
CBN (Medium Grain)

TiN
Al2O3
TiAlN
CBN (Micro Grain)

TiN
Al2O3
TiN
CBN (Micro Grain)

TiN
Al2O3
TiAlN
BC8020
y CONTINUOUS CUTTING
FINISHED SURFACE
WEAR RESISTANCE
10
0.16
Fracture
Finished Surface (!m)
Conventional Coated CBN

Flank Wear (mm)
0.12
0.08
BC8020
0.04
10
BC8020
10
Cutting Time (min)
Cutting Time (min)
Workpiece : JIS SCr420 (60HRC) Insert : NP-CNGA120408GA
Cutting Speed : 150m/min Feed : 0.15mm/rev Depth of Cut : 0.5mm
Wet Continuous Cutting
y INTERRUPTED CUTTING (CRATER WEAR)
FRACTURE RESISTANCE
Normal wear
BC8020
Workpiece : JIS SCM415 (60HRC)
Medium Interrupted Cutting
Insert : NP-CNGA120408GA
Cutting Speed : 150m/min
Feed : 0.15mm/rev
Depth of Cut : 0.15mm
Dry Interrupted Cutting
BC8020
Conventional
Coated
CBN
Fracturing from crater wear
5000
20000 22000 24000 26000 28000 30000

Number of Impacts
y INTERRUPTED CUTTING (CHIPPING)
FRACTURE RESISTANCE
Normal wear
BC8020
Insert : NP-CNGA120408GA
Feed : 0.2mm/rev
BC8020
Conventional
Coated
CBN
0
5000
10000
15000
Number of Impacts
20000
25000
Chipping
BC8020 exhibits excellent cutting performance for severe or interrupted machining.

B005
MBC010
FINISHED SURFACE
Fracture
0.15
Conventional Coated CBN B
Fracture
Conventional Coated CBN A
Flank Wear (mm)
WEAR RESISTANCE
Conventional Coated CBN B
MBC010
0.1
0.05
10
20
30
MBC010
40
Large wear
(Tool life)
Conventional Coated CBN A
10
Cutting Time (min)
20
30
Cutting Time (min)
Insert : NP-CNGA120408GS2
Feed : 0.05mm/rev
Dry Continuous Cutting
Insert : NP-CNGA120408GS2
Feed : 0.15mm/rev
MBC010 employs TiN based coating for superior, consistent surface finishes.
MBC020
WEAR RESISTANCE
0.10
Conventional
Coated CBN B
Conventional
Coated CBN C
Flank Wear (mm)
0.08
TOUGHNESS
Conventional
Coated CBN A
0.06
Conventional
Coated
CBN A
MBC020
0.04
Conventional
Coated
CBN B
0.02
0.00
MBC020
10
Cutting Time (min)
Workpiece : JIS SCr420 (60HRC)
Round bar
Insert : NP-CNGA120408GA4
Feed : 0.1mm/rev
12
14
16
10
15
Cutting Time (min)
Workpiece : JIS SCr420 (60HRC)
Insert : NP-CNGA120408GA4
Feed : 0.15mm/rev
MBC020 exhibits excellent cutting performance for a wide range of applications from continuous through interrupted machining.
B006
20
NON-COATED CBN SERIES

FEATURES
CBN tool material is produced by mixing the main component
CBN (cubic boron nitride), which has a hardness second only to
diamond, with a special ceramic or metal binder. It is then sintered
at a pressure of over 5GPa and at a temperature of 1200C or
higher.
CBN has lower affinity to iron than diamond. The low affinity
and high hardness properties means that sintered CBN delivers
a superior cutting performance especially during high speed
machining of materials such hardened steel, cast iron and sintered
alloys etc.
y HARDENED STEEL MACHINING

Main
Component
For General Purpose Turning

MB8025
MB810
MB825
By employing a "Particle-activated Sintering Method",

the new sintered CBN technology is recommended
for continuous cutting from medium to high speeds.
For High Speed Continuous Cutting
It features improved wear resistance due to

impregnation with larger CBN particles.
CBN (Coarse grain)

TiN
Al2O3
CBN (Micro Grain)
TiN
Al2O3
For Continuous to Medium Interrupted Cutting CBN (Micro Grain)

Excellent balance of wear resistance and
fracture resistance due to introduction of
micro-grain CBN particles.
For Heavy Interrupted Cutting

MB835
400
Grade
Improved grade employing micro-grain CBN

particles. Excellent fracture resistance for
use in heavy interrupted cutting.
TiN
Al2O3
300
MB810
200
MB8025
100
MB835
MB825
CBN (Micro Grain)

TiN
Al2O3
Continuous
Light
Interrupted
Heavy
Cutting Mode
y CAST IRON MACHINING

Grade
Main
Component
For General Cutting
MB710
General purpose grade with well

balanced wear and fracture
resistance.
CBN
TiC
Al2O3
2500
For Continuous to Interrupted Cutting

Has the larger CBN content and
therefore displays good thermal
conductivity. It is suitable for the high
temperatures that are generated in
high speed cutting.
CBN
Co Base Alloy
For High Speed Cutting
MB4020

conductivity. From high-speed cutting
to interrupted cutting are possible.
CBN
(High Content)
Co Base Alloy
2000
MB730
1500
MB4020
MB730
1000
MBS140
500
For High Speed Cutting and

Roughing of Cast Iron
MBS140
MB5015
Highest CBN content, high thermal

conductivity.
Enables deep depth of cut.
MB710
CBN
AIN
(Solid)
Depth of Cut (mm)
MB5015 is exclusive grade for boring of Centrifugal

casting Cylinder liners in semi finishing or finishing
applications with high with high wear resistance.
B007
MB5015
For Cylinder liner

Poduced to order only.
FEATURES
aMB5015 is exclusive grade for boring of Centrifugal casting Cylinder liners in semi finishing or finishing applications
with high with high wear resistance.

Work Material
Cutting Mode
100
500
1000
1500
Feed
(mm/rev)
Depth of Cut
(mm)
0.3(Finishing) 0.05(Finishing)
0.8(Semi-finishing) 0.2(Semi-finishing)
Centrifugal casting Cast Iron Continuous cutting
Coolant
Wet
CUTTING PERFORMANCE
VB wear
0.40
0.35
Flank Wear (mm)
Defective product
Previous
coated grade
0.30
0.25
Previous coated grade
0.20
0.15
MB5015
0.10
0.05
0
20
40
60
80
100
120
140
160
180
200
Number of Drilling
MB5015
Workpiece : FC200 (Centrifugal casting) &63.0
Cutting Speed : 800m/min Feed : 0.35mm/rev Depth of Cut : 0.03mm
Work : Centrifugal casting Cylinder liner Hole Depth : 100mm
y CAST IRON MACHINING

Grade
CUTTING PERFORMANCE
Main
Component
y Continuous Cutting
V-T Diagram (VB=0.1mm)
For General Cutting

General purpose grade with well
balanced wear and fracture
resistance.
CBN
TiC
Al2O3
For Continuous to Interrupted Cutting
MB730

conductivity. It is suitable for the high
temperatures that are generated in
high speed cutting.
CBN
Co Base Alloy
MB710
MB710
700
600
500
400
300
Ceramics
200
For High Speed Cutting
MB4020

conductivity. From high-speed cutting
to interrupted cutting are possible.
For High Speed Cutting and

Roughing of Cast Iron
MBS140
B008
Highest CBN content, high thermal

conductivity.
Enables deep depth of cut.
CBN
(High Content)
Co Base Alloy
CBN
AIN
(Solid)
10
20
30
40
50 60
100
Cutting Time (min)
<Cutting Condition of MB710 >

Workpiece : JIS FC250
: TNGA160408
Insert
: 0.1mm/rev
Feed
Wet Cutting
<Cutting Condition of Ceramics>

Workpiece : JIS FC250
: TNGA160408
Insert
: 0.1mm/rev
Feed
Dry Cutting
MB4020
SINTERED ALLOY MACHINING
a High cutting edge strength
FEATURES
300
Newly developed special binder provides high

cutting edge strength. Burrs and plasticity
characteristics must be suppressed in interrupted
cutting of sintered alloy machining. Extremely
superior work accuracy is realized because
MB4020 allows selection of a sharper cutting
shape to perform its high cutting edge strength.
200
MB4020
100
a Eexcellent welding resistance
MB835
40
There is almost not welding to the tool cutting

edge because the stable CBN contents is high.
Work cutting dimensional accuracy is stable.
60
80
100
Hardness of Work Material (HRB)
Range of
use
Range of
use
Full face CBN

Full face CBN insert can be used for chamfering that use
higher depth of cut
Full face CBN
CUTTING PERFORMANCE
y Continuous cutting of high density sintered alloy
y Continuous cutting of sintered alloy

2.0
Previous
coated grade A
Finished Surface : Ra (!m)
Finished Surface : Ra (!m)
2.0
1.5
MB4020
1.0
Fracture
Previous
coated grade B
0.5
100
300
500
Fracture
Fracture
Previous
coated grade B
1.0
0.5
MB4020
0
700
Previous
coated grade A
1.5
17
Hardness of Workpiece
34
51
68
85
102
Hardness of Workpiece
Workpiece : High density sintered alloy Insert : NP-CNGA120408
Cutting Speed : 190m/min Feed : 0.15mm/rev
Wet Cutting
Workpiece : Sintered alloy
Wet Cutting
Insert : NP-CNGA120408
Feed : 0.15mm/rev
APPLICATION EXAMPLE
Insert
NP-TNGA160404FS3
NP-TPGX080204FS3
CCGW060204FS
Workpiece
Carburized and quenched alloy
Cutting
Conditions
Component
Carburized and quenched alloy
Variable valve parts
FC250
Oil pump parts
Crankcase
250
100
400450
(mm/rev)
0.1
0.03
0.030.37
Feed
Depth of Cut
(mm)
0.2
0
Result
200
0.05
400 (pieces)
100
0.13
200
300 (pieces)
MB4020
MB4020
MB4020
Previous
coated
grade
Previous
coated
grade
Previous
coated
grade
200
300 (pieces)
B009
CBN
alloy and cast iron.

a Low affinity to iron, thus good surface finishes are possible.
a Grinding can be replaced by machining.
Structural Steel
Esp. Carburized Steel
HRC
(SC, SCM, SCr)
35 65
High Alloy Steel
(SKD, SKH)
Coated
Work Material
Type
a Heat Treated Steel
Non-coated
a Suitable for high speed finishing of heat treated steel, sintered ferrous
Recommended Cutting Conditions

Recommended
Grade
Feed (mm/rev)
Depth of Cut (mm)
Cutting
Mode
High speed
finishing cutting
Continuous cutting
for general purpose
Continuous cutting
Heavy interrupted cutting
for general purpose
Interrupted cutting
for general purpose
Continuous cutting
for general purpose
Interrupted cutting
for general purpose
High speed
finishing cutting
Continuous to light
interrupted cutting
Interrupted cutting
250 (150 400)

200 (80 250)
200 (100 300)
200 (80 250)
150 (60 200)
180 (80 250)
120 (60 150)
200 (150 300)
120 (70 150)
100 (50 120)
MBC010
MBC020
BC8110
BC8020
MB8025
MB810
MB825
MB835
0.2
0.2
0.2
0.3
0.2
0.3
0.2
0.15
0.3
0.3
0.2
0.3
0.3
0.8
0.3
0.5
0.3
0.15
0.5
0.5
a Cast Iron
250
500
JIS FC250
JIS FC300
Ferritic + Pearlitic
Pearlitic
Alloy Cast Iron
Pearlitic
Ferritic
JIS FCD400
Ductile Cast Iron
Ferritic + Pearlitic
Gray Cast Iron
Workpiece
Structure
Work Material
JIS FCD700
Pearlitic
750
1000
1250
MBS140
MB710 MB730
MB4020
MB710
MB730
Feed Depth of Cut

Coolant
(mm/rev) (mm)
1.0
0.5 MBS140 Dry,Wet

5.0
0.4
0.5
Dry,Wet
0.4
0.5
Dry,Wet
a Sintered Alloy
Work Material
Recommended
Grade
Feed (mm/rev)
Depth of Cut (mm)
General Sintered Alloy

High Density Sintered Alloy
Sintered Alloy
MB4020
MB4020
MB4020, MB835
250 (80 300)

150 (80 250)
100 (80 150)
0.2
0.2
0.2
0.3
0.3
0.3
250
300
a Valve Seat
Amount of Hard Particles
None or Small
Hardness of Workpiece (HV)
Large
150
350
Plunge Cut
MB4020
MB825
MB835
Traverse Cut
MB4020
MB710
MB825
a Roll
Work Material
Cast Steel
Adamite Cast Steel
Ductile Cast Iron
Granular Cast Iron
Chilled Cast Iron
High Chromium Steel
High Alloy Steel
High Speed Steel
Cemented Carbide
Grade

Feed (mm/rev)
Depth of Cut (mm)
MB825, MB8025
80 (30 130)
0.3 (0.1 0.5)
0.2 3.0
MB710
80 (30 130)
0.3 (0.1 0.5)
0.2 3.0
MB825, MB8025
80 (30 130)
0.3 (0.1 0.5)
0.2 3.0
MB730
MB730, MBS140
50 (20 70)
20 (10 30)
0.25 (0.1 0.4)

0.2
0.1 3.0
0.2
a Heat Resistant Alloy
B010
Work Material
Grade
Ni Base Heat Resistant Alloy

(e.g. Inconel)
Co Base Heat Resistant Alloy
(e.g. Stellite)

Feed (mm/rev)
Depth of Cut (mm)
MB730
120 (100 150)
0.2
0.5
MB730
70 (50 100)
0.2
0.5
HONING
For the CBN BC8020, MBC010 and MBC020 coated grades, MB4020 and MB710/MB730 a wide range of edge
honing styles are available to cover a large range of applications and to represent Mitsubishi Materials unique cutting tool
technology.
y General
St
ab
le
Cu
ttin
FS Honing
FN Honing
y Continuous
GA Honing
FA Honing
cutting
GA honing is the first recommendation.

GS honing if the depth of cut is 0.1mm or less.
GN honing if the crater wear is large.
FS honing is the first recommendation.

FA honing to improve the initial machining performance.
FN honing if the crater wear is large.
TA Honing
GS Honing
cutting, stable cutting
TS Honing
GN Honing
y Medium
and heavy interrupted cutting,

unstable cutting
Un
sta
TN Honing
ble
1st Recommendation
(General Cutting)
TA honing is the first recommendation.

TS honing if the depth of cut is 0.1mm or less.
TN honing if the crater wear is large.
Cu
ttin
NP-CNGA120408- G A 2
Main Application
EDGE HONING
TYPE
MAIN
APPLICATION
Continuous cutting
For General
Purpose Machining
FAHoning
For Anti Chatter
FSHoning
0.1
Light interrupted cutting
15
Interrupted cutting
For Small Depth of Cut

(Crater wear resistant)
FNHoning
0.1
GAHoning
GNHoning
0.13
25
25
TAHoning
R0.015
R0.015
GSHoning
0.13
35
0.05
25
R0.015
TSHoning
0.13
0.05
15
15
R0.03
Edge Honing Type
(Sharp anti-burr type)
R0
NEW HONING TYPES
R0.03
35
R0.015
TNHoning
0.13
0.05
35
R0.015
R0.015
CONVENTIONAL HONING TYPES

For CBN grades except new honing types, three conventional honing types, namely F, G and T types are available for different
applications.
St
ab
le
NP-CNGA120408- G 2 Main Application
Cu
ttin
F Honing
F Honing
Continuous cutting
G Honing
G Honing
Un
R0
25
R0.03
T Honing
sta
ble
15
0.13
Light interrupted cutting
T Honing
1st Recommendation
(General Cutting)
0.1
Cu
ttin
0.13
Interrupted cutting
35
R0.03
B011
CBN GROOVING SERIES

(GY/MG )
FEATURES
a A combination with a high rigidity holder ensures high accuracy
and long tool life.

Holder rigidity is essential when grooving hardened steel. The GY series Tri Lock system
offers high rigidity equivalent to a 1-piece type despite being a 2-piece type. MG has a wide
insert location face for high gripping force. A combination with these holders allows it to
deliver excellent performance when grooving hardened steel.
a Product line-up for different holder properties

MG for narrow grooves and GY for general grooves are both lined up to allow selection of
the most suitable tool.
CUTTING PERFORMANCE
y Tool life evaluation for the GY holder
0.1
Previous coated grade B
0.08
Flank Wear (mm)
Insert Width (mm)
5.0
4.75
4.0
3.18
3.0
2.5
2.39
Previous coated grade A
0.06
MB8025
0.04
0.02
2.0
0.05
0.1
0.15
0.2
10
60
Feed (mm/rev)
Work Material
Hardness
H Hardened Steel 35 65HRC
110
160
Number of passes
Grade
Cutting Speed
(m/min)
Coolant
MB8025
100
(60 120)
Dry,Wet
Workpiece : JIS SCM415 (HRC60) Depth of Cut : 0.35mm
Dry Cutting
: 0.1mm/rev
Feed
APPLICATION EXAMPLE
GY1G0300F020N-GFGS (Grade : MB8025)
Insert
MGTR43200 (Grade : MB8025)
& 30
Workpiece
SNCM230H (HRC5862)
Transmission shaft
Transmission shaft
129
100
(mm/rev)
0.1
0.05
Cutting
Conditions
Component
Feed
200
400
Result
Previous
coated
grade
(pieces)
200
400
(pieces)
MB8025
MB8025
Fracture
GY achieves longer tool life without fracturing.
B012
SCr420H (HRC6165)
Previous
coated
grade
2.5 times longer tool life than the conventional insert.
CBN BREAKER INSERT

FEATURES
APPLICATION AREA
Depth of Cut (mm)
a Chip Breaker Geometry Designed for Excellent Chip Control

Radial chip breaker ensures optimization of the cutting point and the chip breaker position.
Enables effective chip discharge even when copy machining and prevents the chips from
wrapping around the holder under finish cutting conditions.
a Long Life Coated CBN Grade

Combination of Coating grade & Breaker, high efficiency and long tool life in wide variety of
applications.
0.6
0.4
0.2
BM breaker
Area
BF breaker
Area
0.1
0.2
0.3
(BM/BF Breaker)
Feed (mm/rev)
y CUTTING PERFORMANCE
DEEP CUTTING DEPTH
BM
Breaker
(Deep shoulder Milling)
Good for deep depth
cutting of carburized layer.
Recommend and under
ap=0.6mm
Available in BC8020 grade.
Fracture Fracture
Previous coated
grade
0.15
0.10
0.05
BC8020
0
0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5
Cutting Time (min)
LIGHT CUTTING DEPTH
BF
: BM-CNGM120408TA
Insert
: 0.2mm/rev
Feed
Dry Cutting
Flank Wear (mm)
0.20
MITSUBISHIs Breaker (BF)
Breaker
Good for chip removal
under light depth and feed
cutting.
Recommend and under
ap=0.3mm
Available in BC8110,MBC020 grade.
Workpiece : SCr420H (55HRC)
: BF-CNGG120408TA4
Insert
: 0.2mm/rev
Feed
Dry Cutting
Conventional (Light cutting depth)
MULTI-CORNER TYPE INSERTS

a A single sided, multi-corner type insert has no cutting edges on the underside.
Double Sided, multi-corner type insert, ex.
y Double sided, multi-corner type insert

Upper side
Underside
NP-CNGA120408GA4
No. of Cutting Edge Corners
Single Sided, multi-corner type insert, ex.
NP-CNGA120408GA2
No. of Cutting Edge Corners
10-INSERTS PACKS
10-Insert Pack
Two types of packs for MB8025 Multi-corner type inserts, are available,
a single insert pack and a ten insert pack. For easy storage.
TNP-CNGA120404G2
10-Insert Pack Symbol
B013
WIPER INSERT
a Improving Surface Finish
Under the same machining conditions as conventional breakers, but with the feed rate
increased, the surface finish of the workpiece can be improved.
a Improving Efficiency
Wiper
High feed rates not only shorten machining times but also make it possible to combine
roughing and finishing operations.
a Increased Tool Life

When a change to high feed conditions, the time required to cut one component is decreased,
thus more parts can be machined with each insert. In addition, the high feed rate prevents
rubbing, therefore, delaying the progression of wear and increasing the tool life of the insert.
a Improving Chip Control

Under high feed conditions, the chips generated become thicker and are more easily
broken, thus, chip control is improved.
y Insert example
<Cutting Conditions> Workpiece : Hardened Material (HRC60) Depth of Cut : 0.1mm
Insert : NP-CNGA120408GAWS2 Dry Cutting
Wiper insert for low rigidity workpieces
NP-CNGA120408GAWS2
15
Theoretical finished surface roughness
New wiper edge code
10
Without Wiper
5
with WS wiper
0
0.05
0.1
0.2
0.3
Feed (mm/rev)
NOTES FOR USE

y Restriction for Holders
y No Restriction for Holders
Use a holder with end cutting angle 93 for improving wiper

efficiency. A holder with end cutting angle 91 can improve wiper
efficiency, however, there is no wiper efficiency with other end
cutting angles (60, 90,107etc.).
A standard holders can be used.

( A double clamp, high rigidity tool is
recommended.)
Non
restriction
End Cutting
Angle
End Cutting Angle
95
93
(Specified)
RECOMMENDED CUTTING CONDITIONS AND PERFORMANCE

High feed (high efficiency) application area
High precision finish application area
Depth of Cut (mm)
0.5
0.4
High precision finishing
High feed, high efficiency machining
Cutting Speed: 100m/min Feed: 0.1mm/rev

Depth of Cut: 0.1mm
Dry Cutting
Cutting Speed: 100m/min Feed: 0.3mm/rev

Depth of Cut: 0.1mm
Dry Cutting
Without Wiper
With Wiper
Without Wiper
With Wiper
Ry=3.2!m
Ry=1.0!m
Ry=12.2!m
Ry=1.2!m
0.3
0.2
0.1
0.1
0.2
0.4
Feed (mm/rev)
B014
0.5
a Suitable for materials such as aluminium alloy,
non-ferrous metals, and fibre strengthened plastic.

a Suitable for extremely high speed finishing.
FEATURES
Wear Resistance
Grade
Features
Materials focused on wear resistance
MD205
Coarse grain diamond particles are sintered and wear resistance is

excellent. Use when wear resistance with MD220 is insufficient.
PCD (SINTERED DIAMOND)
Materials for general machining
MD220
Sintered medium grain diamond particles. Wear resistance and fracture

resistance are superbly balanced. Applicable to general finishing of
non-ferrous metals, non-metal cutting, and similar machining.
Materials focused on fracture resistance
MD230
Fine grain diamond particles are used. Fracture resistance and

cutting edge sharpness are excellent. Use when fracture and a
high quality finished surface is demanded with MD220.
Fracture Resistance
APPLICATION
CUTTING PERFORMANCE
Flank Wear (mm)
0.5
: High Si Aluminium Alloy
Workpiece
: P11R,SPGN120308
Tool
: 0.15mm/rev
Feed
: W.S.O
Coolant
HTi10
0.4
0.3
0.2
0.1
MD220
12
16
20
24
28
Grade
MD205
MD220
MD230
Please use when

there is insufficient
resistance to wear
with the MD220.
Apply for general

finishing of
non-ferrous metals
and non-metal
cutting.
Please use when a

fracture has occured
with the MD220 and
you desire a highquality finished
surface.
32
Machined Length (km)

Sintered diamond tool wear for
high Si aluminium alloy cutting
SELECTION STANDARD
a TURNING
Work Material
Recommended Grade
MD220
MD230
Aluminium
1000 (200 1500)
0.2
1.0
Aluminium Alloy (Si < 16%)
800 (200 1200)
0.2
1.0
600 (200 1000)
0.2
1.0
700 (200 1200)
0.2
1.0
MD205
Aluminium Alloy (Si > 16%)
Copper Alloy
Feed (mm/rev)
Depth of Cut (mm)
Strengthened Plastic
600 (100 1000)
0.4
1.0
Glass Fibre Reinforced Plastic
500 (100 800)
0.25
1.0
400 (100 600)
0.3
1.0
Ceramics
50 (30 80)
0.1
1.0
0.15
1.0
0.4
0.2
0.5
Carbon
Hard Rubber
600 (300 800)
Wood Inorganic Board
1300 (300 4000)
Cemented Carbide
15 (5 20)
(Note1) e : 1st recommendation. u : 2nd recommendation

(Note2) Not suitable for steel.
NEW PETIT CUT INSERT SERIES

y FEATURES
a Economical The small PCD delivers long tool life. Eliminates the need for regrinding, making tool management easier and economical.
a With Breaker Chip breaker formed directly on the PCD portion delivers superior chip control.
a Corner R0.05mm inserts are available, making it suitable for the machining of small work corner radii.
B015
Type
Tolerance

Product Name
CLASSIFICATION
Breaker Name
and
Cross Section
Flat Top
Multi-corner Type
Double Sided
Rhombic 80
Rhombic 55
Flat Top
Triangular 60
Rhombic 35
Trigon 80
NP-CNGA_o4 NP-DNGA_o4 NP-SNGA_o4 NP-TNGA_o6 NP-VNGA_o4 NP-WNGA_o6
^ B022
Multi-corner Type
Double Sided
With Wiper
Square 90
^ B025
^ B028
^ B030
^ B032
^ B034
NP-CNGA_o4
^ B022
BF
Multi-corner Type
Double Sided
With Breaker
BF-CNGG_o4 BF-DNGG_o4
^ B022
Flat Top
NEW PETIT CUT
Multi-corner Type
Double Sided G
With Breaker
^ B023
Flat Top
Multi-corner Type
Single Sided
With Wiper
BF
BM
Flat Top
R/L-F
One-corner Type
Single Sided
With Breaker
^ B030, B031
^ B032
^ B034
NP-WNGA_oWS3
^ B027
^ B034
^ B027
BM-CNGM_o2 BM-DNGM_o2
BM-TNGM_o3
^ B027
^ B031
NP-CNMA_o NP-DNMA_o NP-SNMA_o NP-TNMA_o NP-VNMA_o
^ B024
^ B028
BF-CNGM_o2 BF-DNGM_o2
^ B024
One-corner Type
Single Sided
^ B026
^ B024
Multi-corner Type
Single Sided
With Breaker
NP-CNGA_oWS2 NP-DNGA_oWS2J_R/L
^ B023
Multi-corner Type
Single Sided
With Breaker
^ B025
NP-CNGA_o2 NP-DNGA_o2 NP-SNGA_o2 NP-TNGA_o3 NP-VNGA_o2 NP-WNGA_o3
^ B027
^ B028
^ B031
^ B033
NP-CNMM_R/L-F NP-DNMM_R/L-F NP-SNMM_R/L-F NP-TNMM_R/L-F NP-VNMM_R/L-F
^ B055
^ B055
^ B056
^ B056
^ B057
(Note) Two types of packs for type inserts, pack of single insert and pack of ten inserts, are available. (The single pack is standard.)
Please refer to the "Standard of inserts".
B016
NEW
STANDARD
Multi-corner Type
Double Sided G
(Solid CBN)
One-corner Type
M
Single Sided
Breaker Name
and
Cross Section
Flat Top
Flat Top
Rhombic 80
Rhombic 55
Square 90
Triangular 60
CNGA
SNGA
TNGA
^ B024
^ B029
^ B031
SNGA
TNGA
Rhombic 35
Trigon 80
Type
Tolerance
Product Name
CNMA
^ B024, B055
DNGA
Flat Top
VNGA
One-corner Type
G
Single Sided
^ B027, B055 ^ B028, B056 ^ B031, B056 ^ B033, B057
Type
Tolerance
Product Name
NEW PETIT CUT
Multi-corner Type
Single Sided
Breaker Name
and
Cross Section
Flat Top
Rhombic 80
Rhombic 55
Square 90
Triangular 60
Rhombic 35
Trigon 80
NP-VBGW_o2
^ B048
One-corner Type
G
Single Sided
Flat Top
NP-VBGW_o
^ B048
One-corner Type
Single Sided
With Breaker
R-F
NP-VBGT_R-F
^ B064
B017
CLASSIFICATION
Type
Tolerance
Product Name

Breaker Name
and
Cross Section
Flat Top
Multi-corner Type
Single Sided
Rhombic 80
NP-CCGW/B_o2 NP-DCGW_o2
^ B039
Flat Top
Multi-corner Type
Single Sided
G
With Wiper
Rhombic 55
^ B043
Square 90
Triangular 60
Rhombic 35
Trigon 80
NP-TCGW_o3 NP-VCGW_o2
^ B045
^ B049
NP-CCGW_oWS2
^ B040
BF
Multi-corner Type
Single Sided
With Breaker
BF-CCGT_o2 BF-DCGT_o2
^ B040
Flat Top
One-corner Type
Single Sided
^ B040
M
NEW PETIT CUT
^ B044
NP-CCMB_o
Standard
One-corner Type
Single Sided
With Breaker
NP-CCMH
^ B059
Flat Top
One-corner Type
G
Single Sided
NP-CCGW_o NP-DCGW_o
^ B040
Flat Top
One-corner Type
Single Sided
^ B041
Flat Top
One-corner Type
M
Single Sided
^ B044
NP-CCMW_o NP-DCMW_o
NP-WCMW_o
^ B044
^ B049
NP-CCMW
^ B059
NP-DCMT_R/L-F
R/L-F
One-corner Type
Single Sided
With Breaker
^ B060
NP-VCGT_R-F
R-F
One-corner Type
Single Sided
G
With Breaker
^ B064
STANDARD
NEW
Flat Top
Multi-corner Type
G
Single Sided
Flat Top
One-corner Type
Single Sided
CCGW
DCGW
TCGW
^ B041
^ B044
CCMW
DCMW
^ B045
TCMW
TCGW
WCMW
G
^ B041, B059 ^ B044, B060
^ B045, B061
^ B065
(Note) Two types of packs for type inserts, pack of single insert and pack of ten inserts, are available. (The single pack is standard.)
Please refer to the "Standard of inserts".
B018
Breaker Name
and
Cross Section
Flat Top
Multi-corner Type
Single Sided
Rhombic 80
Rhombic 55
Square 90
NP-CPGB_o2
Trigon 80
^ B046
NP-TPGX_o3
Flat Top
Multi-corner Type
Single Sided
Rhombic 35
NP-TPGB_o3
^ B042
Triangular 60
Type
Tolerance
Product Name
^ B046
Flat Top
NEW PETIT CUT
One-corner Type
Single Sided
M
Standard
One-corner Type
Single Sided
With Breaker
NP-CPMB_o
NP-TPMB_o
^ B042
^ B046
NP-CPMH
^ B059
One-corner Type
G
Single Sided
NP-TPGX_o
Flat Top
^ B047
NP-TPMX_R/L-F
R/L-F
One-corner Type
Single Sided
With Breaker
^ B062
M
One-corner Type
Single Sided
With Breaker
NP-TPMH_R/L-F
R/L-F
^ B062
One-corner Type
Single Sided
With Breaker
Standard
CPGT
WPGT
STANDARD
^ B059
One-corner Type
G
Single Sided
One-corner Type
Single Sided
With Breaker
Flat Top
R/L-F
^ B065
SPGX
TPGX
^ B060
^ B047, B063
TPGT/V_R/L-F
^ B062, B063
B019

Tolerance
CLASSIFICATION
Type
One-corner Type
Single Sided
G
For Aluminium
With Breaker
Breaker Name
and
Cross Section
R/L
Rhombic 35
VDGX_R/L-F
^ B067
Tolerance

Type
One-corner Type
Single Sided
For Aluminium
With Breaker
Rhombic 55
^ B066
R/L-F
One-corner Type
Single Sided
(For Aluminium)
Triangular 60
TEGX_R/L
R/L
One-corner Type
Single Sided
G
For Aluminium
With Breaker
Breaker Name
and
Cross Section
DEGX_R/L-F
^ B066
Flat Top
TEGX
^ B066
B020
Rhombic 80
Rhombic 55
Flat Top
One-corner Type
Single Sided
G
Flat Top
Multi-corner Type
Double Sided
(Solid CBN)
Tolerance
Breaker Name
and
Cross Section
Flat Top
Triangular 60
SNGN
TNGN
Round
^ B037, B058
^ B038
CNGN
DNGN
SNGN
TNGN
RNGN
^ B035
^ B035
^ B037
^ B038
^ B036

Type
Square 90
Breaker Name
and
Cross Section
SPECIAL PURPOSE INSERTS
Triangular 60
Tool Holder
Type
Tolerance
Type
Tolerance
TBGN
Inserts
GY_GFGS
Multi-corner Type
G
Single Sided
GY Type
^ B052
^ B053
MGTR
Type
Tolerance

Breaker Name
and
Cross Section
Flat Top
Square 90
Triangular 60
SPGN
TPGN
MG Type
G
^ B054
RTG-A
TL Type
^ B050
One-corner Type
G
Single Sided
^ B051, B068
^ B052, B068
B021
Hardened Materials
Cast Iron
: Stable Cutting
Coated
CBN
NEW PETIT CUT
NEG
WITH
HOLE
Order Number
NEW PETIT CUT
CBN
IC
RE
D1
12.7 4.76
0.4
5.16
NP-CNGA120408GA4
12.7 4.76
0.8
5.16
NP-CNGA120412GA4
12.7 4.76
1.2
5.16
NP-CNGA120404GN4
12.7 4.76
0.4
5.16
NP-CNGA120408GN4
12.7 4.76
0.8
5.16
NP-CNGA120412GN4
12.7 4.76
1.2
5.16
NP-CNGA120404GS4
12.7 4.76
0.4
5.16
NP-CNGA120408GS4
12.7 4.76
0.8
5.16
NP-CNGA120412GS4
12.7 4.76
1.2
5.16
NP-CNGA120404FS4
a a
12.7 4.76
0.4
5.16
NP-CNGA120408FS4
a a
12.7 4.76
0.8
5.16
NP-CNGA120412FS4
a a
12.7 4.76
1.2
5.16
NP-CNGA120404TA4
12.7 4.76
0.4
5.16
NP-CNGA120408TA4
12.7 4.76
0.8
5.16
NP-CNGA120412TA4
12.7 4.76
1.2
5.16
NP-CNGA120404TS4
12.7 4.76
0.4
5.16
NP-CNGA120408TS4
12.7 4.76
0.8
5.16
12.7 4.76
1.2
5.16
NP-CNGA120404GAWS4
12.7 4.76
0.4
5.16
NP-CNGA120408GAWS4
12.7 4.76
0.8
5.16
NP-CNGA120412GAWS4
12.7 4.76
1.2
5.16
NP-CNGA120404GSWS4
12.7 4.76
0.4
5.16
NP-CNGA120408GSWS4
12.7 4.76
0.8
5.16
NP-CNGA120412GSWS4
12.7 4.76
1.2
5.16
12.7 4.76
0.4
5.16
BF-CNGG120404TA4
BF-CNGG120408TA4
12.7 4.76
0.8
5.16
BF-CNGG120412TA4
12.7 4.76
1.2
5.16
* Please refer to B014 before using the wiper insert.
B022
Dimensions (mm)
(With Breaker)
Solid
CBN
NP-CNGA120404GA4
NP-CNGA120412TS4
NEW PETIT CUT
(With Wiper)
: Unstable Cutting
: Inventory maintained in Japan. (1 insert in one case)
Applicable
Holder Page
Sintered Alloy
Shape
: General Cutting
Geometry
80
RE
C008
C009
E013
E036
E040
H006
008
D1
H
K
S
IC
80
C008
C009
E013
E036
E040
H006
008
RE
D1
Work
Material
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN TURNING INSERTS
CBN
CN
IC
C008
C009
E013
E036
E040
H006
008
80
RE
D1
80
TYPE INSERTS
WITH HOLE
IC
: Stable Cutting
NEW PETIT CUT
Solid
CBN
Dimensions (mm)
IC
RE
D1
NP-CNGA120404GA2
12.7 4.76
0.4
5.16
NP-CNGA120408GA2
12.7 4.76
0.8
5.16
NP-CNGA120412GA2
12.7 4.76
1.2
5.16
12.7 4.76
0.2
5.16
NP-CNGA120402GS2
NP-CNGA120404GS2
a a
a a
12.7 4.76
0.4
5.16
NP-CNGA120408GS2
a a
a a
12.7 4.76
0.8
5.16
NP-CNGA120412GS2
a a
a a
12.7 4.76
1.2
5.16
NP-CNGA120404GN2
12.7 4.76
0.4
5.16
NP-CNGA120408GN2
12.7 4.76
0.8
5.16
NP-CNGA120412GN2
12.7 4.76
1.2
5.16
NP-CNGA120402FS2
12.7 4.76
0.2
5.16
NP-CNGA120404FS2
a a
12.7 4.76
0.4
5.16
NP-CNGA120408FS2
a a
12.7 4.76
0.8
5.16
NP-CNGA120412FS2
a a
12.7 4.76
1.2
5.16
NP-CNGA120404TA2
12.7 4.76
0.4
5.16
NP-CNGA120408TA2
12.7 4.76
0.8
5.16
NP-CNGA120412TA2
12.7 4.76
1.2
5.16
NP-CNGA120404TS2
12.7 4.76
0.4
5.16
NP-CNGA120408TS2
12.7 4.76
0.8
5.16
NP-CNGA120412TS2
12.7 4.76
1.2
5.16
12.7 4.76
0.4
5.16
NP-CNGA120408G2
12.7 4.76
0.8
5.16
NP-CNGA120412G2
12.7 4.76
1.2
5.16
NP-CNGA120404T2
12.7 4.76
0.4
5.16
NP-CNGA120408T2
12.7 4.76
0.8
5.16
NP-CNGA120412T2
12.7 4.76
1.2
5.16
NEW PETIT CUT TNP-CNGA120404G2
12.7 4.76
0.4
5.16
TNP-CNGA120408G2
12.7 4.76
0.8
5.16
TNP-CNGA120412G2
12.7 4.76
1.2
5.16
TNP-CNGA120404T2
12.7 4.76
0.4
5.16
TNP-CNGA120408T2
12.7 4.76
0.8
5.16
TNP-CNGA120412T2
12.7 4.76
1.2
5.16
NEW PETIT CUT NP-CNGA120404GAWS2

(With Wiper)
*
*
NP-CNGA120408GAWS2
NP-CNGA120412GAWS2
a a
12.7 4.76
0.4
5.16
a a
12.7 4.76
0.8
5.16
a a
12.7 4.76
1.2
5.16
NP-CNGA120404GSWS2
a a
12.7 4.76
0.4
5.16
NP-CNGA120408GSWS2
a a
12.7 4.76
0.8
5.16
NP-CNGA120412GSWS2
a a
12.7 4.76
1.2
5.16
Applicable
Holder Page
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN
NP-CNGA120404G2
*2
: Unstable Cutting
Geometry
NEG
WITH
HOLE
C008
C009
E013
E036
E040
H006
008
80
RE
D1
Coated
CBN
Order Number
: General Cutting
Sintered Alloy
Shape
CBN
Cast Iron
CBN TURNING INSERTS
Hardened Materials
IC
C008
C009
E013
E036
E040
H006
008
80
RE
D1
H
K
S
IC
C008
C009
E013
E036
E040
H006
008
80
RE
D1
Work
Material
IC

GRADES
IDENTIFICATION
B004
B002
B023
Hardened Materials
Cast Iron
: Stable Cutting
Coated
CBN
Shape
NEW PETIT CUT
(With Breaker)
Order Number
: General Cutting
Solid
CBN
CBN
Dimensions (mm)
IC
RE
D1
BF-CNGM120404TA2
12.7 4.76
0.4
5.16
BF-CNGM120408TA2
12.7 4.76
0.8
5.16
BF-CNGM120412TA2
12.7 4.76
1.2
5.16
BF-CNGM120404TS2
12.7 4.76
0.4
5.16
BF-CNGM120408TS2
12.7 4.76
0.8
5.16
BF-CNGM120412TS2
12.7 4.76
1.2
5.16
12.7 4.76
0.8
5.16
NEW PETIT CUT BM-CNGM120408TA2
12.7 4.76
1.2
Geometry
C008
C009
E013
E036
E040
H006
008
80
RE
IC
C008
C009
E013
E036
E040
H006
008
80
RE
5.16
D1
BM-CNGM120412TA2
: Unstable Cutting
Sintered Alloy
NEG
WITH
HOLE
H
K
S
Applicable
Holder Page
Work
Material
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN TURNING INSERTS
CBN
CN
D1
80
TYPE INSERTS
WITH HOLE
IC
a a
12.7 4.76
0.4
5.16
NP-CNMA120408GS
a a
12.7 4.76
0.8
5.16
NP-CNMA120412GS
a a
12.7 4.76
1.2
5.16
NP-CNMA120404G
12.7 4.76
0.4
5.16
NP-CNMA120408G
12.7 4.76
0.8
5.16
NP-CNMA120412G
12.7 4.76
1.2
5.16
NP-CNMA120404F
r a
12.7 4.76
0.4
5.16
NP-CNMA120408F
r a
12.7 4.76
0.8
5.16
NP-CNMA120412F
r a
12.7 4.76
1.2
5.16
NP-CNMA120404T
a a
12.7 4.76
0.4
5.16
NP-CNMA120408T
a a
12.7 4.76
0.8
5.16
NP-CNMA120412T
a a
12.7 4.76
1.2
5.16
12.7 4.76
0.4
5.16
CNMA120404
a a
CNMA120408
a a
12.7 4.76
0.8
5.16
a a
12.7 4.76
1.2
5.16
CNMA120412
80
IC
RE
12.7 4.76
0.8
5.16
12.7 4.76
1.2
5.16
80
RE
D1
CNGA120412
C008
C009
E013
E036
E040
H006
008
C008
C009
E013
E036
E040
H006
008
80
IC
CNGA120408
C008
C009
E013
E036
E040
H006
008
RE
D1
NEW PETIT CUT NP-CNMA120404GS
D1
(With Breaker)
IC
: Inventory maintained in Japan. r : Non stock, produced to order only.

B024
: Stable Cutting
Coated
CBN
NEW PETIT CUT
CBN
Solid
CBN
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
Order Number
: General Cutting
Dimensions (mm)
IC
RE
D1
NP-DNGA150404GA4
12.7
4.76 0.4 5.16
NP-DNGA150408GA4
12.7
4.76 0.8 5.16
NP-DNGA150412GA4
12.7
4.76 1.2 5.16
NP-DNGA150404GN4
12.7
4.76 0.4 5.16
NP-DNGA150408GN4
12.7
4.76 0.8 5.16
NP-DNGA150412GN4
12.7
4.76 1.2 5.16
NP-DNGA150404GS4
12.7
4.76 0.4 5.16
NP-DNGA150408GS4
12.7
4.76 0.8 5.16
NP-DNGA150412GS4
12.7
4.76 1.2 5.16
NP-DNGA150604GS4
12.7
6.35 0.4 5.16
NP-DNGA150608GS4
12.7
6.35 0.8 5.16
NP-DNGA150612GS4
12.7
6.35 1.2 5.16
NP-DNGA150404FS4
a a
12.7
4.76 0.4 5.16
NP-DNGA150408FS4
a a
12.7
4.76 0.8 5.16
NP-DNGA150412FS4
a a
12.7
4.76 1.2 5.16
NP-DNGA150604FS4
12.7
6.35 0.4 5.16
NP-DNGA150608FS4
12.7
6.35 0.8 5.16
NP-DNGA150612FS4
12.7
6.35 1.2 5.16
NP-DNGA150404TA4
12.7
4.76 0.4 5.16
NP-DNGA150408TA4
12.7
4.76 0.8 5.16
NP-DNGA150412TA4
12.7
4.76 1.2 5.16
NP-DNGA150404TS4
12.7
4.76 0.4 5.16
NP-DNGA150408TS4
12.7
4.76 0.8 5.16
NP-DNGA150412TS4
12.7
4.76 1.2 5.16
NP-DNGA150604TS4
12.7
6.35 0.4 5.16
NP-DNGA150608TS4
12.7
6.35 0.8 5.16
NP-DNGA150612TS4
12.7
6.35 1.2 5.16
12.7
4.76 0.4 5.16
NEW PETIT CUT BF-DNGG150404TA4
BF-DNGG150408TA4
12.7
4.76 0.8 5.16
BF-DNGG150412TA4
12.7
4.76 1.2 5.16
(With Breaker)
: Unstable Cutting
Sintered Alloy
Shape
CBN
Cast Iron
Geometry
CBN TURNING INSERTS
Hardened Materials
Applicable
Holder Page
H
K
S
NEG
WITH
HOLE
55
C010
C011
E013
E036
040
H009
011
RE
D1
Work
Material
DN
IC
C010
C011
E013
E036
040
H009
011
55
RE
D1
55
TYPE INSERTS
WITH HOLE
IC
GRADES
IDENTIFICATION
B004
B002
B025
Hardened Materials
Cast Iron
: Stable Cutting

Sintered Alloy
Coated
CBN
Shape
NEW PETIT CUT
NEG
WITH
HOLE
Order Number
Solid
CBN
CBN
IC
RE
D1
NP-DNGA110408GA2
NP-DNGA150404GA2
12.7
4.76 0.4 5.16
NP-DNGA150408GA2
12.7
4.76 0.8 5.16
NP-DNGA150412GA2
12.7
4.76 1.2 5.16
Geometry
9.525 4.76 0.8 3.81
NP-DNGA150402GS2
12.7
4.76 0.2 5.16
NP-DNGA150404GS2
a a
a a
12.7
4.76 0.4 5.16
NP-DNGA150408GS2
a a
a a
12.7
4.76 0.8 5.16
NP-DNGA150412GS2
a a
a a
12.7
4.76 1.2 5.16
NP-DNGA150604GS2
12.7
6.35 0.4 5.16
NP-DNGA150608GS2
12.7
6.35 0.8 5.16
NP-DNGA150612GS2
12.7
6.35 1.2 5.16
NP-DNGA150404GN2
12.7
4.76 0.4 5.16
NP-DNGA150408GN2
12.7
4.76 0.8 5.16
NP-DNGA150412GN2
12.7
4.76 1.2 5.16
12.7
4.76 0.2 5.16
NP-DNGA150402FS2
NP-DNGA150404FS2
a a
12.7
4.76 0.4 5.16
NP-DNGA150408FS2
a a
12.7
4.76 0.8 5.16
NP-DNGA150412FS2
a a
12.7
4.76 1.2 5.16
NP-DNGA150604FS2
12.7
6.35 0.4 5.16
NP-DNGA150608FS2
12.7
6.35 0.8 5.16
NP-DNGA150612FS2
12.7
6.35 1.2 5.16
NP-DNGA150404TA2
12.7
4.76 0.4 5.16
NP-DNGA150408TA2
12.7
4.76 0.8 5.16
NP-DNGA150412TA2
12.7
4.76 1.2 5.16
NP-DNGA150404TS2
12.7
4.76 0.4 5.16
NP-DNGA150408TS2
12.7
4.76 0.8 5.16
NP-DNGA150412TS2
12.7
4.76 1.2 5.16
NP-DNGA150604TS2
12.7
6.35 0.4 5.16
NP-DNGA150608TS2
12.7
6.35 0.8 5.16
NP-DNGA150612TS2
12.7
6.35 1.2 5.16
12.7
4.76 0.4 5.16
NP-DNGA150408G2
12.7
4.76 0.8 5.16
NP-DNGA150412G2
12.7
4.76 1.2 5.16
NP-DNGA150404T2
12.7
4.76 0.4 5.16
NP-DNGA150408T2
12.7
4.76 0.8 5.16
NP-DNGA150412T2
12.7
4.76 1.2 5.16
NEW PETIT CUT TNP-DNGA150404G2
12.7
4.76 0.4 5.16
TNP-DNGA150408G2
12.7
4.76 0.8 5.16
TNP-DNGA150412G2
12.7
4.76 1.2 5.16
TNP-DNGA150404T2
12.7
4.76 0.4 5.16
TNP-DNGA150408T2
12.7
4.76 0.8 5.16
TNP-DNGA150412T2
12.7
4.76 1.2 5.16
* The order number is for a 10-insert pack. Please specify order number, grade and quantity.
: Unstable Cutting
Dimensions (mm)
NP-DNGA150404G2
B026
: General Cutting
Applicable
Holder Page
H
K
S
C010
C011
E013
E036
040
H009
011
55
RE
D1
Work
Material
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN TURNING INSERTS
CBN
DN
IC
C010
C011
E013
E036
040
H009
011
55
RE
D1
55
TYPE INSERTS
WITH HOLE
IC
: Stable Cutting
Dimensions (mm)
IC
RE
12.7
4.76 0.4 5.16
NP-DNGA150404GAWS2JL
a a
12.7
4.76 0.4 5.16
NP-DNGA150408GAWS2JR
a a
12.7
4.76 0.8 5.16
NP-DNGA150408GAWS2JL
a a
12.7
4.76 0.8 5.16
12.7
4.76 0.4 5.16
55
C010
C011
E013
E036
040
H009
011
RE
IC
NP-DNGA150404GSWS2JL
12.7
4.76 0.4 5.16
NP-DNGA150408GSWS2JR
12.7
4.76 0.8 5.16
NP-DNGA150408GSWS2JL
12.7
4.76 0.8 5.16 Right hand insert shown.
BF-DNGM150404TA2
12.7
4.76 0.4 5.16
BF-DNGM150408TA2
12.7
4.76 0.8 5.16
BF-DNGM150412TA2
12.7
4.76 1.2 5.16
BF-DNGM150404TS2
12.7
4.76 0.4 5.16
BF-DNGM150408TS2
12.7
4.76 0.8 5.16
BF-DNGM150412TS2
12.7
4.76 1.2 5.16
NEW PETIT CUT BM-DNGM150408TA2
12.7
4.76 0.8 5.16
BM-DNGM150412TA2
12.7
4.76 1.2 5.16
55
RE
IC
55
RE
D1
(With Breaker)
Geometry
D1
a a
NP-DNGA150404GSWS2JR
NEW PETIT CUT
Solid
CBN
CBN
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
NEW PETIT CUT NP-DNGA150404GAWS2JR

(With Wiper)
: Unstable Cutting
Applicable
Holder Page
Coated
CBN
Order Number
: General Cutting
Sintered Alloy
Shape
CBN
Cast Iron
IC
(With Breaker)
12.7
4.76 0.4 5.16
a a
12.7
4.76 0.8 5.16
NP-DNMA150404G
12.7
4.76 0.4 5.16
NP-DNMA150408G
12.7
4.76 0.8 5.16
NP-DNMA150412G
12.7
4.76 1.2 5.16
NP-DNMA150404F
r a
12.7
4.76 0.4 5.16
NP-DNMA150408F
r a
12.7
4.76 0.8 5.16
NP-DNMA150412F
12.7
4.76 1.2 5.16
NP-DNMA150404T
a a
12.7
4.76 0.4 5.16
NP-DNMA150408T
a a
12.7
4.76 0.8 5.16
NP-DNMA150412T
12.7
4.76 1.2 5.16
DNGA150404
r r
12.7
4.76 0.4 5.16
DNGA150408
r r
12.7
4.76 0.8 5.16
DNGA150412
r r
12.7
4.76 1.2 5.16
55
IC
55
WITH
HOLE
C010
C011
E013
E036
040
H009
011
C010
C011
E013
E036
040
H009
011
C010
C011
E013
E036
040
H009
011
RE
IC
NEG
C010
C011
E013
E036
040
H009
011
RE
D1
a a
NP-DNMA150408GS
D1
NEW PETIT CUT NP-DNMA150404GS
CBN TURNING INSERTS
Hardened Materials
D1
H
K
S
D1
Work
Material
GRADES
IDENTIFICATION
B004
B002
B027
Hardened Materials
Cast Iron
: Stable Cutting
: General Cutting
: Unstable Cutting
Sintered Alloy
Coated
CBN
Solid
CBN
CBN
Shape
Order Number
NEW PETIT CUT
NP-SNGA120404GA4
NP-SNGA120408GA4
NP-SNGA120412GA4
NEG
Dimensions (mm)
IC
RE
D1
12.7 4.76
0.4
5.16
12.7 4.76
0.8
5.16
12.7 4.76
1.2
5.16
Geometry
RE
NP-SNGA120408GS2
a a
NP-SNGA120412GS2
a a
NEW PETIT CUT
NEW PETIT CUT
12.7 4.76
0.4
5.16
12.7 4.76
0.8
5.16
12.7 4.76
1.2
5.16
NP-SNGA120404FS2
12.7 4.76
0.4
5.16
NP-SNGA120408FS2
12.7 4.76
0.8
5.16
NP-SNGA120412FS2
12.7 4.76
1.2
5.16
NP-SNGA120404TS2
12.7 4.76
0.4
5.16
NP-SNGA120408TS2
12.7 4.76
0.8
5.16
12.7 4.76
1.2
5.16
NP-SNGA120404G2
12.7 4.76
0.4
5.16
NP-SNGA120408G2
12.7 4.76
0.8
5.16
NP-SNGA120412G2
12.7 4.76
1.2
5.16
NP-SNGA120404T2
12.7 4.76
0.4
5.16
NP-SNGA120408T2
12.7 4.76
0.8
5.16
NP-SNGA120412T2
12.7 4.76
1.2
5.16
TNP-SNGA120404G2
12.7 4.76
0.4
5.16
TNP-SNGA120408G2
12.7 4.76
0.8
5.16
TNP-SNGA120412G2
12.7 4.76
1.2
5.16
TNP-SNGA120404T2
12.7 4.76
0.4
5.16
TNP-SNGA120408T2
12.7 4.76
0.8
5.16
TNP-SNGA120412T2
12.7 4.76
1.2
5.16
NP-SNMA120404GS
a a
12.7 4.76
0.4
5.16
NP-SNMA120408GS
a a
12.7 4.76
0.8
5.16
NP-SNMA120404G
12.7 4.76
0.4
5.16
NP-SNMA120408G
12.7 4.76
0.8
5.16
NP-SNMA120412G
12.7 4.76
1.2
5.16
NP-SNMA120404F
r a
12.7 4.76
0.4
5.16
NP-SNMA120408F
r a
12.7 4.76
0.8
5.16
NP-SNMA120412F
r a
12.7 4.76
1.2
5.16
NP-SNMA120404T
a a
12.7 4.76
0.4
5.16
NP-SNMA120408T
a a
12.7 4.76
0.8
5.16
NP-SNMA120412T
a a
12.7 4.76
1.2
5.16
SNGA120404
r r
12.7 4.76
0.4
5.16
SNGA120408
a a
12.7 4.76
0.8
5.16
SNGA120412
a a
12.7 4.76
1.2
5.16

C012
015
E014
E035
S
IC
RE
C012
015
E014
E035
S
IC
RE
C012
015
E014
E035
S
IC
RE
IC
C012
015
E014
E035
RE
D1
D1
NP-SNGA120404GS2
D1
NEW PETIT CUT
NP-SNGA120412TS2
B028
IC
D1
WITH
HOLE
H
K
S
Applicable
Holder Page
Work
Material
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN TURNING INSERTS
CBN
SN
D1
90
TYPE INSERTS
WITH HOLE
C012
015
E014
E035
: Stable Cutting
CBN
Solid
CBN
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
Coated
CBN
Order Number
: General Cutting
: Unstable Cutting
Sintered Alloy
Shape
CBN
Cast Iron
Dimensions (mm)
IC
RE
D1
SNGA120408
12.7 4.76
0.8
5.16
SNGA120412
12.7 4.76
1.2
5.16
Geometry
CBN TURNING INSERTS
Hardened Materials
Applicable
Holder Page
H
K
S
RE
C012
015
E014
E035
D1
Work
Material
IC
GRADES
IDENTIFICATION
NEG
WITH
HOLE
B004
B002
B029
Hardened Materials
Cast Iron
: Stable Cutting

Sintered Alloy
Coated
CBN
Shape
NEW PETIT CUT
NEG
WITH
HOLE
NEW PETIT CUT
Order Number
: General Cutting
: Unstable Cutting
Solid
CBN
CBN
Dimensions (mm)
IC
RE
D1
NP-TNGA160404GA6
9.525 4.76
0.4
3.81
NP-TNGA160408GA6
9.525 4.76
0.8
3.81
NP-TNGA160412GA6
9.525 4.76
1.2
3.81
NP-TNGA160404GN6
9.525 4.76
0.4
3.81
NP-TNGA160408GN6
9.525 4.76
0.8
3.81
NP-TNGA160412GN6
9.525 4.76
1.2
3.81
NP-TNGA160404GS6
9.525 4.76
0.4
3.81
NP-TNGA160408GS6
9.525 4.76
0.8
3.81
NP-TNGA160412GS6
9.525 4.76
1.2
3.81
NP-TNGA160404FS6
a a
9.525 4.76
0.4
3.81
NP-TNGA160408FS6
a a
9.525 4.76
0.8
3.81
NP-TNGA160412FS6
a a
9.525 4.76
1.2
3.81
NP-TNGA160404TA6
9.525 4.76
0.4
3.81
NP-TNGA160408TA6
9.525 4.76
0.8
3.81
NP-TNGA160412TA6
9.525 4.76
1.2
3.81
NP-TNGA160404TS6
9.525 4.76
0.4
3.81
NP-TNGA160408TS6
9.525 4.76
0.8
3.81
NP-TNGA160412TS6
NP-TNGA160402GA3
9.525 4.76
1.2
3.81
9.525 4.76
0.2
3.81
NP-TNGA160404GA3
9.525 4.76
0.4
3.81
NP-TNGA160408GA3
9.525 4.76
0.8
3.81
NP-TNGA160412GA3
9.525 4.76
1.2
3.81
9.525 4.76
0.2
3.81
NP-TNGA160402GS3
NP-TNGA160404GS3
a a
9.525 4.76
0.4
3.81
NP-TNGA160408GS3
a a
a a
9.525 4.76
0.8
3.81
NP-TNGA160412GS3
a a
a a
9.525 4.76
1.2
3.81
NP-TNGA160402GN3
9.525 4.76
0.2
3.81
NP-TNGA160404GN3
9.525 4.76
0.4
3.81
NP-TNGA160408GN3
9.525 4.76
0.8
3.81
NP-TNGA160412GN3
9.525 4.76
1.2
3.81
NP-TNGA160402FS3
9.525 4.76
0.2
3.81
NP-TNGA160404FS3
a a
9.525 4.76
0.4
3.81
NP-TNGA160408FS3
a a
9.525 4.76
0.8
3.81
NP-TNGA160412FS3
a a
9.525 4.76
1.2
3.81
NP-TNGA160404TA3
9.525 4.76
0.4
3.81
NP-TNGA160408TA3
9.525 4.76
0.8
3.81
NP-TNGA160412TA3
9.525 4.76
1.2
3.81
NP-TNGA160404TS3
9.525 4.76
0.4
3.81
NP-TNGA160408TS3
9.525 4.76
0.8
3.81
NP-TNGA160412TS3
9.525 4.76
1.2
3.81
Applicable
Holder Page
H
K
S
Geometry
RE
D1
Work
Material
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN TURNING INSERTS
CBN
TN
IC
RE
IC

B030
C016
C017
E014
E035
E039
C016
C017
E014
E035
E039
D1
60
TYPE INSERTS
WITH HOLE
: Stable Cutting
Solid
CBN
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN
Dimensions (mm)
IC
RE
D1
NEW PETIT CUT NP-TNGA160404G3
9.525 4.76
0.4
3.81
NP-TNGA160408G3
9.525 4.76
0.8
3.81
NP-TNGA160412G3
9.525 4.76
1.2
3.81
NP-TNGA160404T3
9.525 4.76
0.4
3.81
NP-TNGA160408T3
9.525 4.76
0.8
3.81
NP-TNGA160412T3
9.525 4.76
1.2
3.81
NEW PETIT CUT TNP-TNGA160404G3
9.525 4.76
0.4
3.81
TNP-TNGA160408G3
9.525 4.76
0.8
3.81
TNP-TNGA160412G3
9.525 4.76
1.2
3.81
TNP-TNGA160404T3
9.525 4.76
0.4
3.81
TNP-TNGA160408T3
9.525 4.76
0.8
3.81
TNP-TNGA160412T3
9.525 4.76
1.2
3.81
: Unstable Cutting
9.525 4.76
0.8
3.81
BM-TNGM160412TA3
9.525 4.76
1.2
3.81
Geometry
RE
C016
C017
E014
E035
E039
IC
IC
9.525 4.76
0.4
3.81
a a
9.525 4.76
0.8
3.81
a a
NP-TNMA160412GS
9.525 4.76
1.2
3.81
NP-TNMA160404G
9.525 4.76
0.4
3.81
NP-TNMA160408G
9.525 4.76
0.8
3.81
NP-TNMA160412G
9.525 4.76
1.2
3.81
NP-TNMA160404F
r a
9.525 4.76
0.4
3.81
NP-TNMA160408F
r a
9.525 4.76
0.8
3.81
NP-TNMA160412F
r a
9.525 4.76
1.2
3.81
NP-TNMA160404T
a a
9.525 4.76
0.4
3.81
NP-TNMA160408T
a a
9.525 4.76
0.8
3.81
NP-TNMA160412T
9.525 4.76
1.2
3.81
TNGA160404
a a
9.525 4.76
0.4
3.81
TNGA160408
a a
9.525 4.76
0.8
3.81
a a
TNGA220404
a r
12.7
4.76
0.4
5.16
TNGA220408
a r
12.7
4.76
0.8
5.16
TNGA220412
a r
12.7
4.76
1.2
5.16
9.525 4.76
0.8
3.81
TNGA160412
9.525 4.76
1.2
3.81
IC
C016
C017
E014
E035
E039
C016
C017
E014
E035
E039
RE
IC
RE
D1
TNGA160408
C016
C017
E014
E035
E039
RE
D1
a a
NP-TNMA160408GS
D1
NP-TNMA160404GS
WITH
HOLE
RE
IC
(With Breaker)
NEW PETIT CUT
NEG
RE
D1
NEW PETIT CUT BM-TNGM160408TA3
Applicable
Holder Page
Coated
CBN
Order Number
: General Cutting
Sintered Alloy
Shape
CBN
Cast Iron
CBN TURNING INSERTS
Hardened Materials
D1
H
K
S
D1
Work
Material
IC
C016
C017
E014
E035
E039
C016
C017
E014
E035
E039
GRADES
IDENTIFICATION
B004
B002
B031
Cast Iron
: Stable Cutting

Sintered Alloy
Coated
CBN
Shape
NEW PETIT CUT
NEG
WITH
HOLE
NEW PETIT CUT
Order Number
: General Cutting
Solid
CBN
CBN
Dimensions (mm)
IC
RE
D1
NP-VNGA160404GA4
9.525 4.76
0.4
3.81
NP-VNGA160408GA4
9.525 4.76
0.8
3.81
NP-VNGA160412GA4
9.525 4.76
1.2
3.81
NP-VNGA160404GS4
9.525 4.76
0.4
3.81
NP-VNGA160408GS4
9.525 4.76
0.8
3.81
NP-VNGA160412GS4
9.525 4.76
1.2
3.81
NP-VNGA160404FS4
a a
9.525 4.76
0.4
3.81
NP-VNGA160408FS4
a a
9.525 4.76
0.8
3.81
NP-VNGA160412FS4
9.525 4.76
1.2
3.81
NP-VNGA160404TA4
9.525 4.76
0.4
3.81
NP-VNGA160408TA4
9.525 4.76
0.8
3.81
NP-VNGA160412TA4
9.525 4.76
1.2
3.81
9.525 4.76
0.4
3.81
NP-VNGA160404TS4
NP-VNGA160408TS4
9.525 4.76
0.8
3.81
9.525 4.76
0.2
3.81
NP-VNGA160404GA2
9.525 4.76
0.4
3.81
NP-VNGA160408GA2
9.525 4.76
0.8
3.81
NP-VNGA160402GA2
NP-VNGA160402GS2
9.525 4.76
0.2
3.81
NP-VNGA160404GS2
a a
9.525 4.76
0.4
3.81
NP-VNGA160408GS2
a a
9.525 4.76
0.8
3.81
NP-VNGA160412GS2
9.525 4.76
1.2
3.81
9.525 4.76
0.2
3.81
9.525 4.76
0.2
3.81
NP-VNGA160402GN2
NP-VNGA160402FS2
NP-VNGA160404FS2
a a
9.525 4.76
0.4
3.81
NP-VNGA160408FS2
a a
9.525 4.76
0.8
3.81
NP-VNGA160404TA2
9.525 4.76
0.4
3.81
NP-VNGA160408TA2
NP-VNGA160404TS2
NP-VNGA160408TS2
9.525 4.76
0.8
3.81
9.525 4.76
0.4
3.81
9.525 4.76
0.8
3.81
NP-VNGA160404G2
9.525 4.76
0.4
3.81
NP-VNGA160408G2
9.525 4.76
0.8
3.81
NP-VNGA160404T2
9.525 4.76
0.4
3.81
NP-VNGA160408T2
9.525 4.76
0.8
3.81
NEW PETIT CUT TNP-VNGA160404G2
9.525 4.76
0.4
3.81
TNP-VNGA160408G2
9.525 4.76
0.8
3.81
TNP-VNGA160404T2
9.525 4.76
0.4
3.81
TNP-VNGA160408T2
9.525 4.76
0.8
3.81
: Unstable Cutting
Geometry
35
RE
IC

B032
C018
020
E015
E041
35
RE
IC
35
C018
020
E015
E041
S
RE
IC
Applicable
Holder Page
Hardened Materials
D1
H
K
S
D1
Work
Material
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN TURNING INSERTS
CBN
VN
C018
020
E015
E041
D1
35
TYPE INSERTS
WITH HOLE
: Stable Cutting
: Unstable Cutting
Solid
CBN
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN
Dimensions (mm)
IC
RE
D1
NEW PETIT CUT NP-VNMA160404GS
a a
9.525 4.76
0.4
3.81
NP-VNMA160408GS
a a
9.525 4.76
0.8
3.81
NP-VNMA160404G
9.525 4.76
0.4
3.81
NP-VNMA160408G
9.525 4.76
0.8
3.81
NP-VNMA160404F
r a
9.525 4.76
0.4
3.81
NP-VNMA160408F
r a
9.525 4.76
0.8
3.81
NP-VNMA160404T
a a
9.525 4.76
0.4
3.81
NP-VNMA160408T
a a
9.525 4.76
0.8
3.81
VNGA160404
r r
9.525 4.76
0.4
3.81
VNGA160408
r r
9.525 4.76
0.8
3.81
Applicable
Holder Page
Coated
CBN
Order Number
: General Cutting
Sintered Alloy
Shape
CBN
Cast Iron
Geometry
CBN TURNING INSERTS
Hardened Materials
35
RE
C018
020
E015
E041
D1
H
K
S
IC
35
NEG
WITH
HOLE
RE
C018
020
E015
E041
D1
Work
Material
IC
GRADES
IDENTIFICATION
B004
B002
B033
Hardened Materials
Cast Iron
: Stable Cutting
Coated
CBN
Shape
NEW PETIT CUT
Order Number
NP-WNGA080408GA6
: General Cutting
: Unstable Cutting
Sintered Alloy
NEG
Solid
CBN
CBN
Dimensions (mm)
IC
RE
D1
12.7 4.76
0.8
5.16
NP-WNGA080408GS6
12.7 4.76
0.8
5.16
NP-WNGA080408FS6
12.7 4.76
0.8
5.16
NP-WNGA080408TS6
12.7 4.76
0.8
5.16
Geometry
80
RE
IC
NEW PETIT CUT
NP-WNGA080408GA3
12.7 4.76
0.8
5.16
12.7 4.76
0.8
5.16
NP-WNGA080408GS3
NP-WNGA080408FS3
12.7 4.76
0.8
5.16
NP-WNGA080408TS3
12.7 4.76
0.8
5.16
80
RE
12.7 4.76
0.8
5.16
12.7 4.76
0.8
5.16
80
RE
C021
E015
D1
NP-WNGA080408GSWS3
a a
a a
C021
E015
S
IC
NEW PETIT CUT NP-WNGA080408GAWS3

(With Wiper)
C021
E015
D1
WITH
HOLE
H
K
S
Applicable
Holder Page
Work
Material
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN TURNING INSERTS
CBN
WN
D1
80
TYPE INSERTS
WITH HOLE
IC
B034
Work
Material
H
K
S
CN
Hardened Materials
CBN
Cast Iron
: Stable Cutting
: General Cutting
: Unstable Cutting

Sintered Alloy
Order Number
Solid
CBN
Dimensions (mm)
IC
RE
CNGN120404
12.7
4.76
0.4
CNGN120408
12.7
4.76
0.8
CNGN120412
12.7
4.76
1.2
Geometry
80
RE
IC
55
Work
Material
H
K
S
DN
Applicable
Holder Page
Shape
CBN
BC8020
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
Coated
CBN
CBN TURNING INSERTS
80
TYPE INSERTS
WITHOUT HOLE
NEG
WITHOUT
HOLE
TYPE INSERTS
WITHOUT HOLE
Hardened Materials
Cast Iron
: Stable Cutting
: General Cutting
: Unstable Cutting

Sintered Alloy
Order Number
Solid
CBN
Dimensions (mm)
IC
RE
DNGN110308
9.525
3.18
0.8
DNGN110312
9.525
3.18
1.2
Applicable
Holder Page
Shape
CBN
BC8020
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
Coated
CBN
Geometry
55
RE
IC
GRADES
IDENTIFICATION
B004
B002
B035
RN
Work
Material
H
K
S
Hardened Materials
Cast Iron
: Stable Cutting
: General Cutting
: Unstable Cutting

Sintered Alloy
Shape
NEG
Order Number
CBN
Solid
CBN
Dimensions (mm)
IC
9.525
3.18
RNGN090300
RNGN120300
12.7
3.18
RNGN120400
12.7
4.76
Geometry
IC
WITHOUT
HOLE

B036
Applicable
Holder Page
Coated
CBN
BC8020
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN TURNING INSERTS
CBN
TYPE INSERTS
WITHOUT HOLE
Work
Material
H
K
S
SN
Hardened Materials
CBN
Cast Iron
: Stable Cutting
: General Cutting
: Unstable Cutting

Sintered Alloy
Order Number
Dimensions (mm)
IC
RE
SNGN090304
r r
9.525
3.18
0.4
SNGN090308
r r
9.525
3.18
0.8
SNGN120404
r r
12.7
4.76
0.4
SNGN120408
a r
12.7
4.76
0.8
SNGN120412
a r
12.7
4.76
1.2
SNGN090308
9.525
3.18
0.8
SNGN090312
9.525
3.18
1.2
SNGN090316
9.525
3.18
1.6
SNGN090408
9.525
4.76
0.8
SNGN090412
9.525
4.76
1.2
SNGN120408
12.7
4.76
0.8
SNGN120412
12.7
4.76
1.2
SNGN120416
12.7
4.76
1.6
Applicable
Holder Page
Shape
Solid
CBN
CBN
BC8020
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
Coated
CBN
Geometry
RE
IC
CBN TURNING INSERTS
90
TYPE INSERTS
WITHOUT HOLE
NEG
WITHOUT
HOLE
RE
IC
GRADES
IDENTIFICATION
B004
B002
B037
60
Work
Material
H
K
S
Hardened Materials
Cast Iron
: Stable Cutting
: General Cutting
: Unstable Cutting

Sintered Alloy
Shape
Order Number
Solid
CBN
CBN
Dimensions (mm)
IC
RE
TNGN160404
a r
9.525
4.76
0.4
TNGN160408
a r
9.525
4.76
0.8
Applicable
Holder Page
Coated
CBN
BC8020
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
MBS140
CBN TURNING INSERTS
CBN
TN
TYPE INSERTS
WITHOUT HOLE
Geometry
RE
NEG
IC
WITHOUT
HOLE
TNGN160408
9.525
4.76
0.8
TNGN160412
9.525
4.76
1.2
TNGN160416
9.525
4.76
1.6
RE
IC

B038
CBN TURNING INSERTS [POSITIVE]
H
K
S
Hardened Materials
: Stable Cutting
Coated
CBN
CBN
: Unstable Cutting
Dimensions (mm)
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
Order Number
: General Cutting
Sintered Alloy
Shape
CBN
Cast Iron
NEW PETIT CUT NP-CCGB060204GA2
RE
D1
6.35
2.38
0.4
2.8
Geometry
80
RE
D1
IC
7
S
IC
NP-CCGW060202GA2
6.35
2.38
0.2
2.8
NP-CCGW060204GA2
6.35
2.38
0.4
2.8
NP-CCGW060208GA2
6.35
2.38
0.8
2.8
NP-CCGW09T302GA2
9.525 3.97
0.2
4.4
NP-CCGW09T304GA2
9.525 3.97
0.4
4.4
NP-CCGW09T308GA2
9.525 3.97
0.8
4.4
NP-CCGW060202GS2
a a
6.35
2.38
0.2
2.8
NP-CCGW060204GS2
a a
a a
6.35
2.38
0.4
2.8
NP-CCGW060208GS2
a a
6.35
NP-CCGW09T302GS2
NP-CCGW09T304GS2
a a
NP-CCGW09T308GS2
a a
2.38
0.8
2.8
9.525 3.97
0.2
4.4
a a
9.525 3.97
0.4
4.4
a a
9.525 3.97
0.8
4.4
NP-CCGW09T302GN2
9.525 3.97
0.2
4.4
NP-CCGW09T304GN2
9.525 3.97
0.4
4.4
NP-CCGW09T308GN2
9.525 3.97
0.8
4.4
NP-CCGW060202FA2
a a
6.35
2.38
0.2
2.8
NP-CCGW060204FA2
a a
6.35
2.38
0.4
2.8
NP-CCGW060208FA2
a a
6.35
2.38
0.8
2.8
NP-CCGW09T304FA2
a a
9.525 3.97
0.4
4.4
NP-CCGW09T308FA2
9.525 3.97
0.8
4.4
NP-CCGW060202FS2
a a
6.35
2.38
0.2
2.8
NP-CCGW060204FS2
a a
6.35
2.38
0.4
2.8
NP-CCGW060208FS2
6.35
2.38
0.8
2.8
NP-CCGW09T302FS2
a a
9.525 3.97
0.2
4.4
NP-CCGW09T304FS2
a a
9.525 3.97
0.4
4.4
NP-CCGW09T308FS2
a a
a a
9.525 3.97
0.8
4.4
NP-CCGW060202TS2
6.35
2.38
0.2
2.8
NP-CCGW060204TS2
6.35
2.38
0.4
2.8
NP-CCGW060208TS2
6.35
2.38
0.8
2.8
NP-CCGW09T302TS2
9.525 3.97
0.2
4.4
NP-CCGW09T304TS2
9.525 3.97
0.4
4.4
NP-CCGW09T308TS2
9.525 3.97
0.8
4.4
NP-CCGW09T304G2
9.525 3.97
0.4
4.4
NP-CCGW09T308G2
9.525 3.97
0.8
4.4
80
RE
D1
NEW PETIT CUT
7
IC
C022
D008
E006
E030
E034
CBN TURNING INSERTS
Work
Material
CC
Applicable
Holder Page
80
TYPE INSERTS
WITH HOLE
POSI
7
WITH
HOLE
C022
D008
E006
E030
E034
GRADES
IDENTIFICATION
B004
B002
B039
H
K
S
Hardened Materials
Cast Iron
: Stable Cutting

Sintered Alloy
Coated
CBN
Shape
Order Number
CBN
NEW PETIT CUT TNP-CCGW09T304G2

2
: General Cutting
: Unstable Cutting
Dimensions (mm)
TNP-CCGW09T308G2
IC
RE
D1
9.525 3.97
0.4
4.4
9.525 3.97
0.8
4.4
Applicable
Holder Page
Work
Material
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
CBN TURNING INSERTS
CBN
CC
Geometry
RE
80
POSI
7
NEW PETIT CUT
(With Wiper)
1
NP-CCGW09T308GAWS2
a a
9.525 3.97
0.8
4.4
NP-CCGW09T304GSWS2
9.525 3.97
0.4
4.4
NP-CCGW09T308GSWS2
a a
9.525 3.97
0.8
4.4
S
9.525 3.97
0.4
4.4
BF-CCGT09T308TA2
9.525 3.97
0.8
4.4
BF-CCGT09T304TS2
9.525 3.97
0.4
4.4
BF-CCGT09T308TS2
9.525 3.97
0.8
4.4
80
RE
7
S
IC
(With Breaker)
NEW PETIT CUT NP-CCMB060204G
6.35
2.38
0.4
2.8
80
RE
D1
C022
D008
E030
E034
D1
BF-CCGT09T304TA2
C022
D008
E030
E034
RE
80
IC
NEW PETIT CUT
7
S
IC
D1
WITH
HOLE
C022
D008
E030
E034
D1
80
TYPE INSERTS
WITH HOLE
NP-CCGW09T302GS
NP-CCGW09T304GS
B040
9.525 3.97
0.2
4.4
a a
9.525 3.97
0.4
4.4
NP-CCGW060202G
6.35
2.38
0.2
2.8
NP-CCGW060204G
6.35
2.38
0.4
2.8
NP-CCGW060208G
6.35
2.38
0.8
2.8
NP-CCGW09T302G
9.525 3.97
0.2
4.4
NP-CCGW09T304G
9.525 3.97
0.4
4.4
NP-CCGW09T308G
9.525 3.97
0.8
4.4
NP-CCGW060202F
6.35
2.38
0.2
2.8
NP-CCGW060204F
6.35
2.38
0.4
2.8
NP-CCGW09T302F
9.525 3.97
0.2
4.4
NP-CCGW09T304F
r a
9.525 3.97
0.4
4.4
NP-CCGW09T308F
9.525 3.97
0.8
4.4
NP-CCGW060202T
6.35
2.38
0.2
2.8
NP-CCGW060204T
6.35
2.38
0.4
2.8
NP-CCGW09T302T
9.525 3.97
0.2
4.4
9.525 3.97
0.4
4.4
NP-CCGW09T304T
NP-CCGW09T308T
*
*3 NP-CCGW03S104FS
*3 NP-CCGW04T002FS
*3 NP-CCGW04T004FS
3 NP-CCGW03S102FS
*
*
*
a a
9.525 3.97
0.8
4.4
3.57
1.39
0.2
2.0
3.57
1.39
0.4
2.0
4.37
1.79
0.2
2.4
4.37
1.79
0.4
2.4

3 Diameter of inscribed circle is special. (For SCLC type)
a : Inventory maintained in Japan. r : Non stock, produced to order only.
80
RE
D1
NEW PETIT CUT
IC
C022
D008
E006
E030
E034
7
IC
C022
D008
E006
E030
E034
: Stable Cutting
NEW PETIT CUT
: Unstable Cutting
* NP-CCMW03S102F
* NP-CCMW03S104F
* NP-CCMW04T002F
* NP-CCMW04T004F
IC
RE
D1
3.57
1.39
0.2
2.0
3.57
1.39
0.4
2.0
4.37
1.79
0.2
2.4
4.37
1.79
0.4
2.4
Geometry
80
RE
6.35
2.38
0.2
2.8
CCGW060204FS
6.35
2.38
0.4
2.8
CCGW060208FS
6.35
2.38
0.8
2.8
CCGW09T304FS
9.525 3.97
0.4
4.4
CCGW09T308FS
9.525 3.97
0.8
4.4
CCMW060202
r r
6.35
2.38
0.2
2.8
CCMW060204
r r
6.35
2.38
0.4
2.8
CCMW09T302
r r
9.525 3.97
0.2
4.4
CCMW09T304
r r
9.525 3.97
0.4
4.4
CCMW09T308
r r
9.525 3.97
0.8
4.4
CCMW120404
r r
0.4
5.5
12.7
4.76
CCMW120408
r r
12.7
4.76
0.8
5.5
CCMW120412
r r
12.7
4.76
1.2
5.5
80
E016
7
IC
CCGW060202FS
Applicable
Holder Page
Dimensions (mm)
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
CBN
D1
Coated
CBN
Order Number
: General Cutting
Sintered Alloy
Shape
CBN
Cast Iron
CBN TURNING INSERTS
Hardened Materials
RE
7
S
IC
POSI
7
WITH
HOLE
D1
H
K
S
C022
D008
E006
E030
E034
80
RE
C022
D008
E006
E030
E034
IDENTIFICATION
B004
B002
D1
Work
Material
IC
Diameter of inscribed circle is special. (For SCLC type)
GRADES
B041
Hardened Materials
Cast Iron
: Stable Cutting

Sintered Alloy
Coated
CBN
Shape
NEW PETIT CUT
Order Number
: General Cutting
: Unstable Cutting
CBN
Dimensions (mm)
IC
RE
D1
NP-CPGB080204GA2
7.94
2.38
0.4
3.5
NP-CPGB080208GA2
7.94
2.38
0.8
3.5
9.525 3.18
0.4
4.5
9.525 3.18
0.8
4.5
POSI
11
NP-CPGB090304GA2
NP-CPGB090308GA2
WITH
HOLE
NP-CPGB080204GS2
7.94
2.38
0.4
3.5
NP-CPGB080208GS2
7.94
2.38
0.8
3.5
NP-CPGB090302GS2
9.525 3.18
0.2
4.5
NP-CPGB090304GS2
9.525 3.18
0.4
4.5
NP-CPGB090308GS2
9.525 3.18
0.8
4.5
7.94
2.38
0.2
3.5
7.94
2.38
0.4
3.5
7.94
2.38
0.8
3.5
9.525 3.18
0.2
4.5
NP-CPGB090304FS2
9.525 3.18
0.4
4.5
NP-CPGB090308FS2
9.525 3.18
0.8
4.5
NP-CPGB080202FS2
NP-CPGB080204FS2
a a
NP-CPGB080208FS2
a a
NP-CPGB090302FS2
NEW PETIT CUT NP-CPMB080204G
7.94
2.38
0.4
3.5
NP-CPMB090304G
9.525 3.18
0.4
4.5
Applicable
Holder Page
H
K
S
Geometry
RE
80
D1
Work
Material
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
CBN TURNING INSERTS
CBN
CP
E006
11
S
IC
RE
80
D1
80
TYPE INSERTS
WITH HOLE
E006
11
IC
B042
: Stable Cutting
Coated
CBN
NEW PETIT CUT
CBN
IC
RE
D1
NP-DCGW070202GA2
6.35
2.38
0.2
2.8
NP-DCGW070204GA2
6.35
2.38
0.4
2.8
6.35
NP-DCGW070208GA2
2.38
0.8
2.8
NP-DCGW11T302GA2
9.525 3.97
0.2
4.4
NP-DCGW11T304GA2
9.525 3.97
0.4
4.4
NP-DCGW11T308GA2
9.525 3.97
0.8
4.4
NP-DCGW070202GS2
6.35
2.38
0.2
2.8
NP-DCGW070204GS2
a a
6.35
2.38
0.4
2.8
NP-DCGW070208GS2
6.35
2.38
0.8
2.8
NP-DCGW11T302GS2
a a
9.525 3.97
0.2
4.4
NP-DCGW11T304GS2
a a
a a
9.525 3.97
0.4
4.4
NP-DCGW11T308GS2
a a
a a
9.525 3.97
0.8
4.4
NP-DCGW070202GN2
6.35
2.38
0.2
2.8
NP-DCGW070204GN2
6.35
2.38
0.4
2.8
NP-DCGW070208GN2
6.35
2.38
0.8
2.8
NP-DCGW11T302GN2
9.525 3.97
0.2
4.4
NP-DCGW11T304GN2
9.525 3.97
0.4
4.4
NP-DCGW11T308GN2
NP-DCGW11T304FA2
NP-DCGW11T308FA2
9.525 3.97
0.8
4.4
a a
9.525 3.97
0.4
4.4
a a
9.525 3.97
0.8
4.4
6.35
2.38
0.2
2.8
NP-DCGW070202FS2
a a
NP-DCGW070204FS2
a a
6.35
2.38
0.4
2.8
NP-DCGW070208FS2
6.35
2.38
0.8
2.8
NP-DCGW11T302FS2
a a
9.525 3.97
0.2
4.4
NP-DCGW11T304FS2
a a
9.525 3.97
0.4
4.4
NP-DCGW11T308FS2
a a
9.525 3.97
0.8
4.4
NP-DCGW070204TS2
6.35
2.38
0.4
2.8
NP-DCGW070208TS2
6.35
2.38
0.8
2.8
NP-DCGW11T302TS2
9.525 3.97
0.2
4.4
NP-DCGW11T304TS2
9.525 3.97
0.4
4.4
NP-DCGW11T308TS2
9.525 3.97
0.8
4.4
NP-DCGW11T304G2
9.525 3.97
0.4
4.4
NP-DCGW11T308G2
9.525 3.97
0.8
4.4
NEW PETIT CUT TNP-DCGW11T304G2
9.525 3.97
0.4
4.4
TNP-DCGW11T308G2
9.525 3.97
0.8
4.4
: Unstable Cutting
Dimensions (mm)
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
Order Number
: General Cutting
Sintered Alloy
Shape
CBN
Cast Iron
Geometry
CBN TURNING INSERTS
Hardened Materials
Applicable
Holder Page
H
K
S
POSI
7
WITH
HOLE
55
C023
D009
D026
E008
E009
E029
E031
RE
D1
Work
Material
DC
7
S
IC
C023
D009
D026
E008
E009
E029
E031
55
RE
D1
55
TYPE INSERTS
WITH HOLE
7
S
IC
GRADES
IDENTIFICATION
B004
B002
B043
H
K
S
Hardened Materials
Cast Iron
: Stable Cutting

Sintered Alloy
Coated
CBN
Shape
NEW PETIT CUT
Order Number
BF-DCGT11T304TA2
: Unstable Cutting
Dimensions (mm)
IC
9.525 3.97
RE
D1
0.4
4.4
9.525 3.97
0.8
4.4
BF-DCGT11T304TS2
9.525 3.97
0.4
4.4
BF-DCGT11T308TS2
9.525 3.97
0.8
4.4
Geometry
RE
9.525 3.97
0.2
4.4
a a
9.525 3.97
0.4
4.4
NP-DCGW070202G
6.35
2.38
0.2
2.8
NP-DCGW070204G
6.35
2.38
0.4
2.8
NP-DCGW070208G
6.35
2.38
0.8
2.8
NP-DCGW11T302G
9.525 3.97
0.2
4.4
NP-DCGW11T304G
9.525 3.97
0.4
4.4
NP-DCGW11T308G
9.525 3.97
0.8
4.4
NP-DCGW070202F
6.35
2.38
0.2
2.8
NP-DCGW070204F
6.35
2.38
0.4
2.8
NP-DCGW11T302F
9.525 3.97
0.2
4.4
NP-DCGW11T304F
r a
9.525 3.97
0.4
4.4
NP-DCGW11T308F
9.525 3.97
0.8
4.4
NP-DCGW070202T
6.35
2.38
0.2
2.8
NP-DCGW070204T
6.35
2.38
0.4
2.8
NP-DCGW11T302T
9.525 3.97
0.2
4.4
NP-DCGW11T304T
9.525 3.97
0.4
4.4
NP-DCGW11T308T
9.525 3.97
0.8
4.4
6.35
0.4
2.8
NEW PETIT CUT NP-DCMW070204G
NP-DCMW11T304G
2.38
9.525 3.97
0.4
55
RE
D1
NP-DCGW11T304GS
a a
IC
(With Breaker)
NEW PETIT CUT NP-DCGW11T302GS
C023
D009
D026
E008
E009
E029
E031
55
7
IC
RE
4.4
7
IC
a
6.35
2.38
0.4
2.8
DCGW070208FS
6.35
2.38
0.8
2.8
55
S
RE
D1
DCGW070204FS
IC
r r
6.35
2.38
0.2
2.8
DCMW070204
r r
6.35
2.38
0.4
2.8
DCMW11T302
r r
9.525 3.97
0.2
4.4
DCMW11T304
r r
9.525 3.97
0.4
4.4
55
RE
D1
DCMW070202
7
IC

B044
C023
D009
D026
E008
E009
E029
E031
C023
D009
D026
E008
E009
E029
E031
C023
D009
D026
E008
E009
E029
E031
C023
D009
D026
E008
E009
E029
E031
55
D1
WITH
HOLE
CBN
BF-DCGT11T308TA2
POSI
7
: General Cutting
Applicable
Holder Page
Work
Material
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
CBN TURNING INSERTS
CBN
DC
D1
55
TYPE INSERTS
WITH HOLE
: Stable Cutting
NEW PETIT CUT
: Unstable Cutting
Dimensions (mm)
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
CBN
IC
RE
D1
NP-TCGW090202GA3
5.56
2.38
0.2
2.5
NP-TCGW090204GA3
5.56
2.38
0.4
2.5
NP-TCGW090208GA3
5.56
2.38
0.8
2.5
NP-TCGW110202GA3
6.35
2.38
0.2
2.8
NP-TCGW110204GA3
6.35
2.38
0.4
2.8
NP-TCGW110208GA3
6.35
2.38
0.8
2.8
NP-TCGW130304GA3
7.94
3.18
0.4
3.4
NP-TCGW130308GA3
7.94
3.18
0.8
3.4
NP-TCGW16T304GA3
9.525 3.97
0.4
4.4
NP-TCGW16T308GA3
9.525 3.97
0.8
4.4
NP-TCGW090204GS3
5.56
2.38
0.4
2.5
NP-TCGW090208GS3
5.56
2.38
0.8
2.5
NP-TCGW110202GS3
6.35
2.38
0.2
2.8
NP-TCGW110204GS3
6.35
2.38
0.4
2.8
NP-TCGW110208GS3
6.35
2.38
0.8
2.8
NP-TCGW130304GS3
7.94
3.18
0.4
3.4
NP-TCGW130308GS3
7.94
3.18
0.8
3.4
NP-TCGW16T304GS3
9.525 3.97
0.4
4.4
NP-TCGW16T308GS3
9.525 3.97
0.8
4.4
NP-TCGW110204FA3
a a
6.35
2.38
0.4
2.8
NP-TCGW110208FA3
a a
6.35
2.38
0.8
2.8
NP-TCGW110204FS3
6.35
2.38
0.4
2.8
NP-TCGW110208FS3
6.35
2.38
0.8
2.8
NP-TCGW110204TS3
6.35
2.38
0.4
2.8
NP-TCGW110208TS3
6.35
2.38
0.8
2.8
TCGW090204FS
5.56
2.38
0.4
2.5
TCGW090208FS
5.56
2.38
0.8
2.5
TCGW110204FS
6.35
2.38
0.4
2.8
TCGW110208FS
6.35
2.38
0.8
2.8
Geometry
POSI
7
WITH
HOLE
RE
7
IC
r r
6.35
2.38
0.2
2.8
TCMW110204
r r
6.35
2.38
0.4
2.8
C027
E028
60
RE
7
IC
TCMW110202
Applicable
Holder Page
Coated
CBN
Order Number
: General Cutting
Sintered Alloy
Shape
CBN
Cast Iron
CBN TURNING INSERTS
Hardened Materials
D1
H
K
S
C027
E028
S
RE
D1
Work
Material
TC
D1
60
TYPE INSERTS
WITH HOLE
7
IC
C027
E028
GRADES
IDENTIFICATION
B004
B002
B045
Hardened Materials
Cast Iron
: Stable Cutting

Sintered Alloy
NEW PETIT CUT
Order Number
CBN
Dimensions (mm)
IC
RE
D1
NP-TPGB080204GA3
4.76
2.38
0.4
2.4
NP-TPGB080208GA3
4.76
2.38
0.8
2.4
POSI
11
NP-TPGB090204GA3
5.56
2.38
0.4
2.9
NP-TPGB090208GA3
5.56
2.38
0.8
2.9
WITH
HOLE
NP-TPGB110304GA3
6.35
3.18
0.4
3.4
NP-TPGB110308GA3
6.35
3.18
0.8
3.4
NP-TPGB160304GA3
9.525 3.18
0.4
4.4
NP-TPGB160308GA3
9.525 3.18
0.8
4.4
NEW PETIT CUT
NP-TPGB080204GS3
4.76
2.38
0.4
2.4
NP-TPGB080208GS3
4.76
2.38
0.8
2.4
NP-TPGB090204GS3
5.56
2.38
0.4
2.9
NP-TPGB090208GS3
5.56
2.38
0.8
2.9
NP-TPGB110302GS3
6.35
3.18
0.2
3.4
NP-TPGB110304GS3
6.35
3.18
0.4
3.4
NP-TPGB110308GS3
6.35
3.18
0.8
3.4
NP-TPGB160304GS3
9.525 3.18
0.4
4.4
NP-TPGB160308GS3
9.525 3.18
0.8
4.4
NP-TPGB090202FS3
5.56
2.38
0.2
2.9
NP-TPGB090204FS3
5.56
2.38
0.4
2.9
NP-TPGB110302FS3
6.35
3.18
0.2
3.4
NP-TPGB110304FS3
a a
6.35
3.18
0.4
3.4
NP-TPGB110308FS3
a a
6.35
NP-TPGB160304FS3
NP-TPGB160308FS3
3.18
0.8
3.4
9.525 3.18
0.4
4.4
9.525 3.18
0.8
4.4
NP-TPGX080202GA3
4.76
2.38
0.2
2.5
NP-TPGX080204GA3
4.76
2.38
0.4
2.5
NP-TPGX080208GA3
4.76
2.38
0.8
2.5
NP-TPGX090204GA3
5.56
2.38
0.4
NP-TPGX090208GA3
5.56
2.38
0.8
NP-TPGX110304GA3
6.35
3.18
0.4
3.5
NP-TPGX110308GA3
NEW PETIT CUT
: Unstable Cutting
6.35
3.18
0.8
3.5
NP-TPGX080202GS3
4.76
2.38
0.2
2.5
NP-TPGX080204GS3
4.76
2.38
0.4
2.5
NP-TPGX090202GS3
5.56
2.38
0.2
NP-TPGX090204GS3
5.56
2.38
0.4
NP-TPGX110304GS3
6.35
3.18
0.4
3.5
NP-TPGX110308GS3
6.35
3.18
0.8
3.5
NP-TPMB080204G
4.76
2.38
0.4
2.4
NP-TPMB090204G
5.56
2.38
0.4
2.9
NP-TPMB110304G
6.35
3.18
0.4
3.4
NP-TPMB160304G
9.525 3.18
0.4
4.4
Applicable
Holder Page
Coated
CBN
Shape
: General Cutting
Geometry
60
RE
D1
H
K
S
E007
11
IC
RE
D1
Work
Material
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
CBN TURNING INSERTS
CBN
TP
E025
11
IC
RE
D1
60
TYPE INSERTS
WITH HOLE
E007
11
IC
=
B046
: Stable Cutting
NEW PETIT CUT
Dimensions (mm)
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
CBN
IC
RE
D1
NP-TPGX090204G
5.56
2.38
0.4
NP-TPGX090208G
5.56
2.38
0.8
NP-TPGX110304G
6.35
3.18
0.4
3.5
NP-TPGX110308G
6.35
3.18
0.8
3.5
NP-TPGX080202F
4.76
2.38
0.2
2.5
NP-TPGX080204F
4.76
2.38
0.4
2.5
NP-TPGX090202F
5.56
2.38
0.2
NP-TPGX090204F
5.56
2.38
0.4
NP-TPGX110304F
6.35
3.18
0.4
3.5
NP-TPGX110308F
6.35
3.18
0.8
3.5
NP-TPGX080202T
4.76
2.38
0.2
2.5
NP-TPGX080204T
4.76
2.38
0.4
2.5
NP-TPGX090202T
5.56
2.38
0.2
NP-TPGX090204T
5.56
2.38
0.4
NP-TPGX110304T
a a
6.35
3.18
0.4
3.5
NP-TPGX110308T
a a
6.35
3.18
0.8
3.5
a a
4.76
2.38
0.2
2.5
TPGX080202
TPGX080204
TPGX080208
TPGX090202
a a
4.76
2.38
0.4
2.5
r r
4.76
2.38
0.8
2.5
a a
5.56
2.38
0.2
a a
5.56
2.38
0.4
TPGX090208
r r
5.56
2.38
0.8
TPGX110302
r r
6.35
3.18
0.2
3.5
TPGX090204
: Unstable Cutting
TPGX110304
a a
6.35
3.18
0.4
3.5
TPGX110308
a a
6.35
3.18
0.8
3.5
TPGX160304
a r
9.525 3.18
0.4
4.8
TPGX160308
a r
9.525 3.18
0.8
4.8
TPGX160404
r r
9.525 4.76
0.4
4.8
TPGX160408
r r
9.525 4.76
0.8
4.8
Applicable
Holder Page
Coated
CBN
Order Number
: General Cutting
Sintered Alloy
Shape
CBN
Cast Iron
Geometry
CBN TURNING INSERTS
Hardened Materials
POSI
11
WITH
HOLE
RE
D1
H
K
S
E025
11
IC
RE
D1
Work
Material
11
IC
E025
GRADES
IDENTIFICATION
B004
B002
B047
H
K
S
Hardened Materials
Cast Iron
: Stable Cutting

Sintered Alloy
Coated
CBN
Shape
NEW PETIT CUT
Order Number
: General Cutting
: Unstable Cutting
CBN
Dimensions (mm)
IC
RE
D1
NP-VBGW160404GA2
9.525 4.76
0.4
4.43
NP-VBGW160408GA2
9.525 4.76
0.8
4.43
POSI
5
NP-VBGW110302GS2
6.35
3.18
0.2
2.85
NP-VBGW110304GS2
6.35
3.18
0.4
2.85
WITH
HOLE
NP-VBGW110308GS2
6.35
NP-VBGW160402GS2
NP-VBGW160404GS2
NP-VBGW160408GS2
NP-VBGW110302FS2
NP-VBGW110304FS2
NP-VBGW110308FS2
NP-VBGW160402FS2
3.18
0.8
2.85
9.525 4.76
0.2
4.43
a a
9.525 4.76
0.4
4.43
a a
9.525 4.76
0.8
4.43
6.35
3.18
0.2
2.85
6.35
3.18
0.4
2.85
6.35
3.18
0.8
2.85
9.525 4.76
0.2
4.43
NP-VBGW160404FS2
9.525 4.76
0.4
4.43
NP-VBGW160408FS2
9.525 4.76
0.8
4.43
NP-VBGW110304TS2
6.35
3.18
0.4
2.85
NP-VBGW110308TS2
6.35
3.18
0.8
2.85
NP-VBGW160404TS2
9.525 4.76
0.4
4.43
NP-VBGW160408TS2
0.8
4.43
9.525 4.76
0.4
4.43
NP-VBGW160408G
9.525 4.76
0.8
4.43
Geometry
RE
35
5
S
IC
35
E011
H013
5
IC
B048
D010
D011
E011
E012
H013
RE
D1
9.525 4.76
NEW PETIT CUT NP-VBGW160404G
Applicable
Holder Page
Work
Material
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
CBN TURNING INSERTS
CBN
VB
D1
35
TYPE INSERTS
WITH HOLE
Hardened Materials
: Stable Cutting
Coated
CBN
NEW PETIT CUT
CBN
: Unstable Cutting
Dimensions (mm)
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
Order Number
: General Cutting
Sintered Alloy
Shape
CBN
Cast Iron
IC
RE
D1
NP-VCGW160404GA2
9.525 4.76
0.4
4.4
NP-VCGW160408GA2
9.525 4.76
0.8
4.4
NP-VCGW160404GS2
9.525 4.76
0.4
4.4
NP-VCGW160408GS2
9.525 4.76
0.8
4.4
NP-VCGW160404FS2
a a
9.525 4.76
0.4
4.4
NP-VCGW160408FS2
a a
9.525 4.76
0.8
4.4
NP-VCGW160404TS2
9.525 4.76
0.4
4.4
NP-VCGW160408TS2
9.525 4.76
0.8
4.4
Geometry
35
RE
C028
C029
E032
E033
7
IC
CBN TURNING INSERTS
H
K
S
Applicable
Holder Page
Work
Material
VC
D1
35
TYPE INSERTS
WITH HOLE
POSI
7
WITH
HOLE
H
K
S
Hardened Materials
Cast Iron
: Stable Cutting

Sintered Alloy
Order Number
CBN
: Unstable Cutting
Dimensions (mm)
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
Coated
CBN
Shape
: General Cutting
IC
RE
D1
NP-WCMWL30204FA
4.76 2.38
0.4
2.3
NP-WCMWL30208FA
4.76 2.38
0.8
2.3
Applicable
Holder Page
Work
Material
WC
Geometry
RE
D1
80
TYPE INSERTS
WITH HOLE
7
80
IC
E027
GRADES
IDENTIFICATION
B004
B002
B049
RTG
Work
Material
Hardened Materials
Cast Iron
: Stable Cutting
: General Cutting
: Unstable Cutting
Shape
WITHOUT
HOLE
Order Number
CBN
Dimensions (mm)
IC
L17
D4
RTG05A
3.5
7.5
2.5
RTG06A
3.5
7.5
3.5
RTG07A
11
3.5
RTG08A
11
4.5
RTG10A
10
6.5
14
5.5

Geometry
IC
6
L17
S
Coated
CBN
Applicable
Holder Page
Sintered Alloy
POSI
5
6
B050
H
K
S
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
CBN TURNING INSERTS
CBN
TYPE INSERTS
WITHOUT HOLE
D4
12
C035
Work
Material
H
K
S
SP
Hardened Materials
CBN
Cast Iron
: Stable Cutting
: General Cutting
: Unstable Cutting

Sintered Alloy
Order Number
Dimensions (mm)
IC
RE
SPGN090302
r r
9.525
3.18
0.2
SPGN090304
a r
9.525
3.18
0.4
SPGN090308
a r
9.525
3.18
0.8
SPGN090312
r r
9.525
3.18
1.2
SPGN120304
a a
3.18
0.4
12.7
SPGN120308
a a
12.7
3.18
0.8
SPGN120312
r r
12.7
3.18
1.2
SPGN120408
r r
12.7
4.76
0.8
SPGN120412
r r
12.7
4.76
1.2
Applicable
Holder Page
Shape
CBN
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
Coated
CBN
Geometry
RE
POSI
11
11
IC
CBN TURNING INSERTS
90
TYPE INSERTS
WITHOUT HOLE
WITHOUT
HOLE
GRADES
IDENTIFICATION
B004
B002
B051
60
Work
Material
H
K
S
Hardened Materials
Cast Iron
: Stable Cutting
: General Cutting
: Unstable Cutting

Sintered Alloy
Shape
CBN
Dimensions (mm)
Order Number
TBGN060104
TBGN060108
IC
RE
a r
3.97
1.59
0.4
a r
3.97
1.59
0.8
Applicable
Holder Page
Coated
CBN
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
CBN TURNING INSERTS
CBN
TB
TYPE INSERTS
WITHOUT HOLE
Geometry
RE
POSI
5
11
5
S
IC
WITHOUT
HOLE
60
Work
Material
H
K
S
TP
TYPE INSERTS
WITHOUT HOLE
Hardened Materials
Cast Iron
: Stable Cutting
: General Cutting
: Unstable Cutting

Sintered Alloy
IC
RE
TPGN090204
r r
5.56
2.38
0.4
TPGN110302
r r
6.35
3.18
0.2
TPGN110304
a a
6.35
3.18
0.4
TPGN110308
r r
6.35
3.18
0.8
TPGN160304
a a
9.525
3.18
0.4
TPGN160308
a a
9.525
3.18
0.8
TPGN160312
r r
9.525
3.18
1.2
TPGN160408
r r
9.525
4.76
0.8
TPGN220408
r r
4.76
0.8
12.7

B052
Order Number
Dimensions (mm)
Applicable
Holder Page
Shape
CBN
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
MB4020
Coated
CBN
Geometry
RE
11
IC
E026
H
K
S
Hardened Materials
CBN
Cast Iron
: Stable Cutting
: General Cutting
: Unstable Cutting
Order Number
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
Shape
CBN
Dimensions (mm)
CW
RE
GY1G0200D020N-GFGS
2.00
0.2
20.70
GY1G0239E020N-GFGS
2.39
0.2
20.70
GY1G0250E020N-GFGS
2.50
0.2
20.70
GY1G0300F020N-GFGS
3.00
0.2
20.70
GY1G0318F020N-GFGS
3.18
0.2
20.70
GY1G0400G020N-GFGS
4.00
0.2
25.65
GY1G0475H020N-GFGS
4.75
0.2
25.65
GY1G0500H020N-GFGS
5.00
0.2
25.65
Geometry
RE 0.05
CW 0.03
Coated
CBN
3.0
RE 0.05
GRADES
IDENTIFICATION
Applicable
Holder Page
Sintered Alloy
F028
039
F044
049
F052
079
F084
091
F094
101
B004
B002
CBN TURNING INSERTS
Work
Material
GY
TYPE INSERTS
WITHOUT HOLE
POSI
7
WITHOUT
HOLE
B053
Work
Material
H
K
S
Hardened Materials
Cast Iron
: Stable Cutting
: General Cutting
: Unstable Cutting

Sintered Alloy
NEG
WITH
HOLE
IC
Geometry
RE
MGTR43125
MGTR43150
1.50 3.5 12.7 4.76 0.2
MGTR43200
2.00 3.5 12.7 4.76 0.2
MGTR43250
2.50 4.0 12.7 4.76 0.2
MGTR43300
3.00 4.0 12.7 4.76 0.2
MGTR43350
3.50 5.0 12.7 4.76 0.2
MGTR43400
4.00 5.0 12.7 4.76 0.2
1.25 2.0 12.7 4.76 0.2

Applicable
Holder Page
CW PDPT
RE
PDPT
S
Order Number
Dimensions (mm)
H014
IC
Shape
CBN
CW 0.03
Coated
CBN
BC8020
BC8110
MBC010
MBC020
MB8025
MB810
MB825
MB835
MB710
MB730
CBN TURNING INSERTS
CBN
MGTR
TYPE INSERTS
WITH HOLE
Right hand tool holder only.
B054
GRADES
B004
Non-ferrous Metal

: Stable Cutting
PCD
Order Number
NEW PETIT CUT
NP-CNMM120402R-F
NP-CNMM120402L-F
NP-CNMM120404R-F
Dimensions (mm)
IC
RE
D1
12.7
4.76
0.2
5.16
12.7
4.76
0.2
5.16
12.7
4.76
0.4
5.16
NP-CNMM120404L-F
12.7
4.76
0.4
5.16
NP-CNMM120408R-F
12.7
4.76
0.8
5.16
NP-CNMM120408L-F
12.7
4.76
0.8
5.16
CNMA120404
12.7
4.76
0.4
5.16
CNMA120408
12.7
4.76
0.8
5.16
Geometry
80
C008
C009
E036
E040
H006
008
RE
IC
C008
C009
E036
E040
H006
008
80
RE
D1
(With Breaker)
PCD
: Unstable Cutting
MD220
Shape
: General Cutting
IC
Non-ferrous Metal

: Stable Cutting
PCD
Order Number
NEW PETIT CUT
NP-DNMM150402R-F
NP-DNMM150402L-F
NP-DNMM150404R-F
(With Breaker)
: General Cutting
: Unstable Cutting
Dimensions (mm)
MD220
Shape
WITH
HOLE
IC
RE
D1
12.7
4.76
0.2
5.16
12.7
4.76
0.2
5.16
12.7
4.76
0.4
5.16
NP-DNMM150404L-F
12.7
4.76
0.4
5.16
NP-DNMM150408R-F
12.7
4.76
0.8
5.16
NP-DNMM150408L-F
12.7
4.76
0.8
5.16
DNGA150404
12.7
4.76
0.4
5.16
DNGA150408
12.7
4.76
0.8
5.16
Applicable
Holder Page
Geometry
55
RE
D1
Work
Material
DN
NEG
TYPE INSERTS
WITH HOLE
IC

55
RE
D1
55
PCD TURNING INSERTS
Applicable
Holder Page
Work
Material
CN
D1
80
TYPE INSERTS
WITH HOLE
IC
GRADES
IDENTIFICATION
C010
C011
E013
E036
040
H009
011
C010
C011
E013
E036
040
H009
011
B015
B002
B055
PCD TURNING INSERTS [NEGATIVE]
NEG
Non-ferrous Metal

: Stable Cutting
PCD
Shape
Order Number
NEW PETIT CUT
NP-SNMM120404R-F
NP-SNMM120404L-F
: General Cutting
: Unstable Cutting
Dimensions (mm)
IC
RE
D1
12.7
4.76
0.4
5.16
12.7
4.76
0.4
5.16
NP-SNMM120408R-F
12.7
4.76
0.8
5.16
NP-SNMM120408L-F
12.7
4.76
0.8
5.16
Geometry
RE
IC
12.7
4.76
0.4
5.16
SNGA120408
12.7
4.76
0.8
5.16
RE
D1
SNGA120404
IC
Non-ferrous Metal

: Stable Cutting
NEW PETIT CUT
NP-TNMM160402R-F
(With Breaker)
: Unstable Cutting
Dimensions (mm)
MD220
Order Number
: General Cutting
IC
RE
D1
9.525
4.76
0.2
3.81
NP-TNMM160402L-F
9.525
4.76
0.2
3.81
NP-TNMM160404R-F
9.525
4.76
0.4
3.81
NP-TNMM160404L-F
9.525
4.76
0.4
3.81
NP-TNMM160408R-F
9.525
4.76
0.8
3.81
NP-TNMM160408L-F
9.525
4.76
0.8
3.81
TNGA160402
9.525
4.76
0.2
3.81
TNGA160404
9.525
4.76
0.4
3.81
TNGA160408
9.525
4.76
0.8
3.81
Geometry
RE
IC

B056
C016
C017
E014
E035
E039

RE
IC
Applicable
Holder Page
PCD
Shape
C012
015
E014
E035
TYPE INSERTS
WITH HOLE
D1
TN
D1
60
Work
Material
C012
015
E014
E035
(With Breaker)
WITH
HOLE
Applicable
Holder Page
Work
Material
MD220
PCD TURNING INSERTS
PCD
SN
D1
90
TYPE INSERTS
WITH HOLE
C016
C017
E014
E035
E039

: Stable Cutting
PCD
Order Number
NEW PETIT CUT
NP-VNMM160402R-F
NP-VNMM160402L-F
NP-VNMM160404R-F
NP-VNMM160404L-F
(With Breaker)
PCD
: Unstable Cutting
Dimensions (mm)
MD220
Shape
: General Cutting
IC
RE
D1
9.525
4.76
0.2
3.81
9.525
4.76
0.2
3.81
9.525
4.76
0.4
3.81
9.525
4.76
0.4
3.81
NP-VNMM160408R-F
9.525
4.76
0.8
3.81
NP-VNMM160408L-F
9.525
4.76
0.8
3.81
VNGA160404
9.525
4.76
0.4
3.81
VNGA160408
9.525
4.76
0.8
3.81
Geometry
35
RE
C018
020
E015
E041
IC

35
NEG
WITH
HOLE
RE
IC
PCD TURNING INSERTS
Non-ferrous Metal
Applicable
Holder Page
D1
Work
Material
VN
C018
020
E015
E041
D1
35
TYPE INSERTS
WITH HOLE
GRADES
IDENTIFICATION
B015
B002
B057
PCD TURNING INSERTS [NEGATIVE]
Work
Material
Non-ferrous Metal

: Stable Cutting
PCD
Shape
Order Number
: General Cutting
: Unstable Cutting
Dimensions (mm)
MD220
PCD TURNING INSERTS
PCD
SN
IC
SNGN120404
12.7
4.76
0.4
SNGN120408
12.7
4.76
0.8
RE
Geometry
RE
IC
NEG
WITHOUT
HOLE

B058
Applicable
Holder Page
90
TYPE INSERTS
WITHOUT HOLE

: Stable Cutting
PCD
Order Number
NEW PETIT CUT
NP-CCMH060202
NP-CCMH060204
PCD
: Unstable Cutting
Dimensions (mm)
MD220
Shape
: General Cutting
IC
RE
D1
6.35
2.38
0.2
2.8
6.35
2.38
0.4
2.8
Geometry
IC
(With Breaker)
NP-CCMW03S102
3.57
1.39
0.2
2.0
NP-CCMW03S104
3.57
1.39
0.4
2.0
NP-CCMW04T002
4.37
1.79
0.2
2.4
NP-CCMW04T004
4.37
1.79
0.4
2.4
80
RE
6.35
2.38
0.2
2.8
CCMW060204
6.35
2.38
0.4
2.8
CCMW09T302
9.525
3.97
0.2
4.4
CCMW09T304
9.525
3.97
0.4
4.4
7
S
80
RE
IC
TYPE INSERTS
WITH HOLE
Non-ferrous Metal

: Stable Cutting
PCD
Order Number
NEW PETIT CUT
NP-CPMH080202
NP-CPMH080204
NP-CPMH090302
NP-CPMH090304
: Unstable Cutting
Dimensions (mm)
MD220
Shape
: General Cutting
IC
RE
D1
7.94
2.38
0.2
3.5
7.94
2.38
0.4
3.5
9.525
3.18
0.2
4.5
9.525
3.18
0.4
4.5
Geometry
E006
11
IC
(With Breaker)
(With Breaker)
RE
80
CPGT080202
7.94
2.38
0.2
3.4
CPGT080204
7.94
2.38
0.4
3.4
CPGT090302
9.525
3.18
0.2
4.4
CPGT090304
9.525
3.18
0.4
4.4
S
RE
80
D1
Work
Material
CP
C022
D008
E006
E016
E030
E034
D1
80
WITH
HOLE
D1
POSI
7
11
IC
CCMW060202
C022
D008
E006
E016
E030
E034
D1
NEW PETIT CUT
RE
80
PCD TURNING INSERTS
Non-ferrous Metal
Applicable
Holder Page
Applicable
Holder Page
Work
Material
CC
D1
80
TYPE INSERTS
WITH HOLE
11
IC
GRADES
IDENTIFICATION
B015
B002
B059
PCD TURNING INSERTS [POSITIVE]
Non-ferrous Metal

: Stable Cutting
Shape
Order Number
NEW PETIT CUT
NP-DCMT070202R-F
NP-DCMT070202L-F
NP-DCMT070204R-F
POSI
7
11
WITH
HOLE
(With Breaker)
: Unstable Cutting
Dimensions (mm)
IC
RE
D1
6.35
2.38
0.2
2.8
6.35
2.38
0.2
2.8
6.35
2.38
0.4
2.8
NP-DCMT070204L-F
6.35
2.38
0.4
2.8
NP-DCMT11T302R-F
9.525
3.97
0.2
4.4
NP-DCMT11T302L-F
9.525
3.97
0.2
4.4
NP-DCMT11T304R-F
9.525
3.97
0.4
4.4
NP-DCMT11T304L-F
9.525
3.97
0.4
4.4
DCMW070202
6.35
2.38
0.2
2.8
DCMW070204
6.35
2.38
0.4
2.8
DCMW11T302
9.525
3.97
0.2
4.4
DCMW11T304
9.525
3.97
0.4
4.4
Geometry
55
RE
7
IC
RE
TYPE INSERTS
WITH HOLE
Non-ferrous Metal

: Stable Cutting
PCD
Order Number
: General Cutting
: Unstable Cutting
Dimensions (mm)
MD220
Shape
C023
D009
D026
E008
E009
E029
E031
IC
SPGX090304
9.525
3.18
0.4
4.8
SPGX090308
9.525
3.18
0.8
4.8
RE
D1
Geometry
RE
D1
Work
Material
SP
C023
D009
D026
E008
E009
E029
E031

55
IC
90
Applicable
Holder Page
PCD
: General Cutting
Applicable
Holder Page
D1
Work
Material
MD220
PCD TURNING INSERTS
PCD
DC
D1
55
TYPE INSERTS
WITH HOLE
11
IC
B060

: Stable Cutting
PCD
Order Number
PCD
: Unstable Cutting
Dimensions (mm)
MD220
Shape
: General Cutting
IC
TCMW110202
6.35
2.38
0.2
2.8
TCMW110204
6.35
2.38
0.4
2.8
RE
D1
Geometry
RE
7
IC
TCGW060102
3.97
1.59
0.2
2.3
TCGW060104
3.97
1.59
0.4
2.3
TCGW060108
3.97
1.59
0.8
2.3
C027
E028
PCD TURNING INSERTS
Non-ferrous Metal
Applicable
Holder Page
POSI
7
RE
WITH
HOLE
D1
Work
Material
TC
D1
60
TYPE INSERTS
WITH HOLE
IC
GRADES
IDENTIFICATION
B015
B002
B061
Non-ferrous Metal

: Stable Cutting
: Unstable Cutting
Dimensions (mm)
Shape
Order Number
IC
NEW PETIT CUT
NP-TPMX090202R-F
5.56
2.38
0.2
NP-TPMX090202L-F
5.56
2.38
0.2
NP-TPMX090204R-F
5.56
2.38
0.4
NP-TPMX090204L-F
5.56
2.38
0.4
NP-TPMX090208R-F
5.56
2.38
0.8
NP-TPMX090208L-F
5.56
2.38
0.8
NP-TPMX110302R-F
6.35
3.18
0.2
3.5
NP-TPMX110302L-F
6.35
3.18
0.2
3.5
NP-TPMX110304R-F
6.35
3.18
0.4
3.5
NP-TPMX110304L-F
6.35
3.18
0.4
3.5
NP-TPMX110308R-F
6.35
3.18
0.8
3.5
NP-TPMX110308L-F
6.35
3.18
0.8
3.5
NP-TPMX160302R-F
9.525
3.18
0.2
4.8
NP-TPMX160302L-F
9.525
3.18
0.2
4.8
NP-TPMX160304R-F
9.525
3.18
0.4
4.8
NP-TPMX160304L-F
9.525
3.18
0.4
4.8
POSI
11
WITH
HOLE
RE
NP-TPMX160308R-F
9.525
3.18
0.8
4.8
(With Breaker)
NP-TPMX160308L-F
9.525
3.18
0.8
4.8
NEW PETIT CUT
NP-TPMH080202R-F
4.76
2.38
0.2
2.5
NP-TPMH080202L-F
4.76
2.38
0.2
2.5
NP-TPMH080204R-F
4.76
2.38
0.4
2.5
NP-TPMH080204L-F
4.76
2.38
0.4
2.5
NP-TPMH090202R-F
5.56
2.38
0.2
2.9
NP-TPMH090202L-F
5.56
2.38
0.2
2.9
NP-TPMH090204R-F
5.56
2.38
0.4
2.9
NP-TPMH090204L-F
5.56
2.38
0.4
2.9
NP-TPMH110302R-F
6.35
3.18
0.2
3.4
NP-TPMH110302L-F
6.35
3.18
0.2
3.4
NP-TPMH110304R-F
6.35
3.18
0.4
3.4
NP-TPMH110304L-F
6.35
3.18
0.4
3.4
NP-TPMH160302R-F
9.525
3.18
0.2
4.4
NP-TPMH160302L-F
9.525
3.18
0.2
4.4
NP-TPMH160304R-F
9.525
3.18
0.4
4.4
NP-TPMH160304L-F
9.525
3.18
0.4
4.4
TPGT160302R-F
9.525
3.18
0.2
4.4
TPGT160302L-F
9.525
3.18
0.2
4.4
TPGT160304R-F
9.525
3.18
0.4
4.4
TPGT160304L-F
9.525
3.18
0.4
4.4
(With Breaker)
(With Breaker)

B062
Geometry
D1
Applicable
Holder Page
PCD
: General Cutting
RE
D1
11
IC
E025
RE
D1
Work
Material
MD220
PCD TURNING INSERTS
PCD
TP
11
IC
E007

RE
D1
60
TYPE INSERTS
WITH HOLE
11
IC
Non-ferrous Metal
(With Breaker)
Order Number
Dimensions (mm)
MD220
Shape
PCD
: Unstable Cutting
IC
TPGV090202R-F
5.56
2.38
0.2
2.8
TPGV090202L-F
5.56
2.38
0.2
2.8
TPGV090204R-F
5.56
2.38
0.4
2.8
TPGV090204L-F
5.56
2.38
0.4
2.8
TPGV110302R-F
6.35
3.18
0.2
3.4
RE
D1
TPGV110302L-F
6.35
3.18
0.2
3.4
TPGV110304R-F
6.35
3.18
0.4
3.4
TPGV110304L-F
6.35
3.18
0.4
3.4
TPGX080202
4.76
2.38
0.2
2.5
TPGX080204
4.76
2.38
0.4
2.5
TPGX080208
4.76
2.38
0.8
2.5
TPGX090202
5.56
2.38
0.2
TPGX090204
5.56
2.38
0.4
TPGX090208
5.56
2.38
0.8
TPGX110302
6.35
3.18
0.2
3.5
TPGX110304
6.35
3.18
0.4
3.5
TPGX110308
6.35
3.18
0.8
3.5
TPGX160304
9.525
3.18
0.4
4.8
TPGX160308
9.525
3.18
0.8
4.8
Geometry
PCD TURNING INSERTS
PCD
: General Cutting
Applicable
Holder Page
: Stable Cutting
POSI
11
RE
D1
11
IC
WITH
HOLE
RE
D1
Work
Material
11
IC
E025
GRADES
IDENTIFICATION
B015
B002
B063
POSI
5
7
Non-ferrous Metal

: Stable Cutting
PCD
Shape
Order Number
: General Cutting
: Unstable Cutting
Dimensions (mm)
IC
NP-VBGT1103V5R-F
6.35
3.18
0.05
2.85
NP-VBGT110301R-F
6.35
3.18
0.1
2.85
NP-VBGT110302R-F
6.35
3.18
0.2
2.85
NP-VBGT110304R-F
6.35
3.18
0.4
2.85
RE
D1
Applicable
Holder Page
Work
Material
MD220
PCD TURNING INSERTS
PCD
VB
Geometry
35
RE
D1
35
TYPE INSERTS
WITH HOLE
5
S
IC
(With Breaker)
D010
D011
E011
E012
WITH
HOLE
Non-ferrous Metal

: Stable Cutting
PCD
(With Breaker)
Dimensions (mm)
IC
NP-VCGT0802V5R-F
4.76
2.38
0.05
2.4
NP-VCGT080201R-F
4.76
2.38
0.1
2.4
NP-VCGT080202R-F
4.76
2.38
0.2
2.4
NP-VCGT080204R-F
4.76
2.38
0.4
2.4
NP-VCGT1103V5R-F
6.35
3.18
0.05
2.8
NP-VCGT110301R-F
6.35
3.18
0.1
2.8
NP-VCGT110302R-F
6.35
3.18
0.2
2.8
NP-VCGT110304R-F
6.35
3.18
0.4
2.8
RE
D1

B064
Order Number
: Unstable Cutting
MD220
Shape
: General Cutting
Applicable
Holder Page
Work
Material
VC
Geometry
35
RE
D1
35
TYPE INSERTS
WITH HOLE
7
IC
C028
E011
E012
E032
Non-ferrous Metal

: Stable Cutting
PCD
Order Number
PCD
: Unstable Cutting
Dimensions (mm)
MD220
Shape
: General Cutting
IC
WCMWL30202
4.76
2.38
0.2
2.3
WCMWL30204
4.76
2.38
0.4
2.3
WCMW040202
6.35
2.38
0.2
2.8
WCMW040204
6.35
2.38
0.4
2.8
WCMW06T304
9.525
3.97
0.4
4.4
WCMW06T308
9.525
3.97
0.8
4.4
RE
D1
Geometry
80
RE
E027
7
IC
PCD TURNING INSERTS
Applicable
Holder Page
Work
Material
WC
D1
80
TYPE INSERTS
WITH HOLE
POSI
7
11
WITH
HOLE
Non-ferrous Metal

: Stable Cutting
PCD
(With Breaker)
Order Number
: Unstable Cutting
Dimensions (mm)
MD220
Shape
: General Cutting
IC
WPGT040202
6.35
2.38
0.2
2.8
WPGT040204
6.35
2.38
0.4
2.8
WPGT060302
9.525
3.18
0.2
4.4
WPGT060304
9.525
3.18
0.4
4.4
RE
D1
Applicable
Holder Page
Work
Material
WP
Geometry
80
RE
D1
80
TYPE INSERTS
WITH HOLE
E010
11
IC
GRADES
IDENTIFICATION
B015
B002
B065
Non-ferrous Metal

: Stable Cutting
Shape
Order Number
: General Cutting
: Unstable Cutting
Dimensions (mm)
IC
DEGX150402R-F
12.7
4.76
0.2
5.1
DEGX150402L-F
12.7
4.76
0.2
5.1
DEGX150404R-F
12.7
4.76
0.4
5.1
DEGX150404L-F
12.7
4.76
0.4
5.1
RE
D1
Geometry
55
RE
C032
IC
TE
TYPE INSERTS
WITH HOLE
Non-ferrous Metal

: Stable Cutting
PCD
: Unstable Cutting
Dimensions (mm)
MD220
Order Number
: General Cutting
IC
TEGX160302R
9.525
3.18
0.2
4.3
TEGX160302L
9.525
3.18
0.2
4.3
TEGX160304R
9.525
3.18
0.4
4.3
TEGX160304L
9.525
3.18
0.4
4.3
RE
D1
Geometry
RE
D1
60
Shape
20
(With Breaker)
Work
Material
Applicable
Holder Page
PCD
POSI
20
WITH
HOLE
Applicable
Holder Page
Work
Material
MD220
PCD TURNING INSERTS
PCD
DE
D1
55
TYPE INSERTS
WITH HOLE
20
S
IC
(With Breaker)
a
9.525
3.18
0.2
4.3
TEGX160304
9.525
3.18
0.4
4.3
RE
D1
TEGX160302
20
IC
B066
C033
E042
C033
E042
Non-ferrous Metal

: Stable Cutting
PCD
Order Number
PCD
: Unstable Cutting
Dimensions (mm)
MD220
Shape
: General Cutting
IC
VDGX160302R-F
9.525
3.18
0.2
4.5
VDGX160302L-F
9.525
3.18
0.2
4.5
VDGX160304R-F
9.525
3.18
0.4
4.5
VDGX160304L-F
9.525
3.18
0.4
4.5
RE
D1
Geometry
35
RE
C034
POSI
15
15
IC
(With Breaker)
PCD TURNING INSERTS
Applicable
Holder Page
Work
Material
VD
D1
35
TYPE INSERTS
WITH HOLE
WITH
HOLE
GRADES
IDENTIFICATION
B015
B002
B067
Non-ferrous Metal

: Stable Cutting
PCD
Shape
Order Number
POSI
11
WITHOUT
HOLE
Dimensions (mm)
IC
RE
9.525
3.18
0.2
9.525
3.18
0.4
SPGN090308
9.525
3.18
0.8
SPGN090312
9.525
3.18
1.2
SPGN120304
3.18
0.4
SPGN120308
12.7
3.18
0.8
SPGN120312
12.7
3.18
1.2
TP
12.7
Non-ferrous Metal
RE
11
S
IC

: Stable Cutting
: General Cutting
: Unstable Cutting
Dimensions (mm)
MD220
Order Number
Geometry
TYPE INSERTS
WITHOUT HOLE
IC
TPGN110302
6.35
3.18
0.2
TPGN110304
6.35
3.18
0.4
TPGN110308
6.35
3.18
0.8
TPGN160302
9.525
3.18
0.2
TPGN160304
9.525
3.18
0.4
TPGN160308
9.525
3.18
0.8
TPGN160312
9.525
3.18
1.2
RE

B068
SPGN090304
PCD
Shape
: Unstable Cutting
SPGN090302
60
Work
Material
: General Cutting
Applicable
Holder Page
Work
Material
MD220
PCD TURNING INSERTS
PCD
SP
Applicable
Holder Page
90
TYPE INSERTS
WITHOUT HOLE
Geometry
RE
E026
11
IC
GRADES
IDENTIFICATION
B015
B002
Memo
B069

OF EXTERNAL TURNING TOOLS
zOrganized according to turning insert shape.
FIGURE SHOWING THE TOOLING APPLICATION

uses illustrations and arrows to depict the available
machining applications such as external turning,
copying, facing, and chamfering together with
cutting edge lead angles.
TYPE OF TOOL HOLDER

indicates the first four letters of the order number,
as well as cutting applications.
GEOMETRY
TITLE OF PRODUCT BY INSERT TYPE
CHIP BREAKER BY
CUTTING APPLICATION
PRODUCT SECTION
INSERTS
VN TOOL
HOLDERS
DVPN
Facing, Copying
DOUBLE CLAMP type
FH
Light
MP
(16)
EXTERNAL TURNING
Standard
Right hand tool

holder shown.
Order Number
(16)
DVPNR/L2020K16
a a
DVPNR/L2525M16
a a
VNMG
VNGA
VNGG
Stainless
MS
(16)
LF
Medium
MK
(16)
(16)
G Class
CBN
(16)
Shim
Pin
Clamp
Bridge
(16)
(16)
Clamp
Screw
1604pp
20
20 125 32
20
25 DCSVN32 LLP13 DCK3113 DCS2 DC0520T TKY15F
PWLNR/L1616H06
a a
1604pp
25
25 150 32
25
PWLNR/L2020K06
a a
PWLNR/L2525M06
a a
MP type
Finish
FH
Light
LP
Right hand tool

holder shown.
a a
PVPNR/L2525M16
a a
VNMG
VNGA
VNGG
(16)
Stainless
MS
Wrench
Insert Number
R L
WNMG
LF
06T3pp
16
16 100 22
16
06T3pp
20
20 125 22
20
06T3pp
25
25 150 25
25
(06)
*2
Dimensions (mm)
*1
Shim
Shim
Pin
20
LLSWN3T3
(LLSWN32)
LLP13
LLCL13 LLCS106 HKY25R
25
LLSWN3T3
(LLSWN32)
LLP13
32
LLSWN3T3
(LLSWN32)
LLP13
LH HF WF
LF
Medium
MK
(16)
(16)
G Class
CBN
DWLN
LH HF WF
1604pp
20
20 125 32
20
25
1604pp
25
25 150 32
25
32
DOUBLE CLAMP type
Clamp
Lever
(16)
(16)
Shim
(08)
PV321
PV322
PV323
Right hand tool

holder shown.
(16)
Stock
Clamp
Screw
Wrench
P11S
HSP05008C
E03
HKY25R
DWLNR/L1616H06
a a
P11S
HSP05008C
E03
HKY25R
DWLNR/L2020K06
a a
DWLNR/L2525M06
a a
DWLNR/L2020K08
a a
DWLNR/L2525M08
a a
DWLNR/L3225P08
a a
WNMG
WNMA
WNMG
(08)
Medium to Rough
RP
(08)
LH HF WF
Medium
MK
(06,08)
(08)
Stainless
CBN
MS
(08)
(06,08)
*1
Shim
Pin
Clamp
Bridge
Spring Clamp
Screw
06T3pp
16
16 100 25
16
20
LLSWN3T3
(LLSWN32)
LLP23 DCK2211 DCS2 DC0520T TKY15F
06T3pp
20
20 125 25
20
25
LLSWN3T3
(LLSWN32)
LLSWN3T3
(LLSWN32)
06T3pp 25
LF
Medium
MP
*2
Dimensions (mm)
Insert Number
R L
Lock Pin Lock Screw Stop Ring Wrench
Clamp Torque (N m) : HSP05008C=2.5
Light
LP
Medium
95
(16)
Finish
FH
Standard
Order Number
External turning,
Facing
R/L
Dimensions (mm)
Insert Number
R L
Medium
MP
(16)
Medium
Standard
PVPNR/L2020K16
(06)
Torque (N m) : LLCS106=2.2
*12 Clamp
* Please use shim no. LLSWN32 with 4.76mm thick inserts. When using 4.76mm thick inserts, shim should be ordered separately.
Facing, Copying
Stock
Right hand tool

holder shown.
Stock
117
30
Order Number
95
Spring
Medium
MP
(06)
Order Number
Shim
Light
SH
Stainless
LH HF WF
LL type
External turning,
Facing
MS
* Clamp Torque (N m) : DC0520T=3.5
PVPN
PWLN
R/L
Dimensions (mm)
Insert Number
R L
Medium
LP
Medium
117
30
Stock
INSERTS
WN TOOL
HOLDERS
oo
Finish
EXTERNAL TURNING
oo
Shim
Wrench
25 150 25
25
32
0804pp
20
20 125 31
20
25 LLSWN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
0804pp
25
25 150 31
25
0804pp
32
25 170 31
32
*1 Clamp Torque (N m) : DC0520T=3.5, DC0621T=5.0

*2 Please use shim no. LLSWN32 with 4.76mm thick inserts. When using 4.76mm thick inserts, shim should be ordered separately.
(Note) The insert photos are only examples. The letters refer to the chip breaker and the dimension refers to the inscribed circle.
PWLN type inserts
a
C020
DVPN type inserts

PVPN type inserts
A116 A118
A116 A118
CBN & PCD inserts

LEGEND FOR STOCK

STATUS MARK
REFERENCE PAGE
FOR APPLICABLE INSERTS
is shown on the left hand

page of each double-page
spread.
indicates reference pages

giving details of inserts that are
applicable to the product.
PRODUCT STANDARDS
indicates order numbers,
stock status (per right/left hand),
applicable inserts, dimensions,
and spare parts.

zorder number and hand of tool (right/left).
C000
B032, B033, B057

A070
DWLN type inserts

CBN inserts
A119 A122
A119 A123
B034

SPARE PARTS
TECHNICAL DATA
A070
P001
Q001
C021
PAGE REFERENCE
SPARE PARTS
TECHNICAL DATA
indicates reference pages, including
the above, on the right hand page of
TURNING TOOLS

CLASSIFICATION............................. C002
IDENTIFICATION .............................. C006
METHOD OF HOLDING ................... C007
STANDARD HOLDERS
CNppINSERTS TOOL HOLDERS............ C008
DNppINSERTS TOOL HOLDERS............ C010
SN ppINSERTS TOOL HOLDERS............ C012
TN ppINSERTS TOOL HOLDERS............ C016
VN ppINSERTS TOOL HOLDERS............ C018
WNppINSERTS TOOL HOLDERS............ C021
CCppINSERTS TOOL HOLDERS............ C022
DCppINSERTS TOOL HOLDERS............ C023
RCppINSERTS TOOL HOLDERS............ C024
SC ppINSERTS TOOL HOLDERS............ C026
TC ppINSERTS TOOL HOLDERS............ C027
VC ppINSERTS TOOL HOLDERS............ C028
XC ppINSERTS TOOL HOLDERS............ C030
TL HOLDER ....................................... C035
aAL
HOLDER
DE ppINSERTS TOOL HOLDERS ......... C032

TE ppINSERTS TOOL HOLDERS ......... C033
VD ppINSERTS TOOL HOLDERS ......... C034
by Alphabetical order
*Arranged
C016 PTGN
DCLN
C008
C010
C016
C018
C020
C019
C021
C009
C012
C014
C017
C009
C008
C011
C010
C024
C024
C012
C014
C015
C013
C013
C017
DDJN
DTGN
DVJN
DVPN
DVVN
DWLN
MCLN
MSBN
MSSN
MTJN
PCBN
PCLN
PDHN
PDJN
PRDC
PRGC
PSBN
PSDN
PSKN
PSSN
PSTN
PTFN
C018
C020
C019
C021
C022
C023
C032
C023
C032
C025
C025
C026
C033
C027
C033
C028
C034
C029
C028
C030
C035
PVJN
PVPN
PVVN
PWLN
SCLC
SDJC
SDJE
SDNC
SDNE
SRDC
SRGC
SSSC
STFE
STGC
STGE
SVJC
SVJD
SVPC
SVVC
SXZC
TLHR
C001
CLASSIFICATION
External Turning
Facing
EXTERNAL TURNING
Features
Tool Holder
KAPR=95
a
a
a
a
a
DOUBLE
CLAMP
Holder
a
a
a
a
a
Lever lock type.

ISO standard.
Various holder shapes.
Suitable for light to
heavy cutting.
Economical negative
insert.
10 x 10 x 70 25 x 25 x 150
12 x 12 x 80 32 x 25 x 170
16 x 16 x 100 32 x 32 x 170
20 x 20 x 125
KAPR
PCLN
(For heavy cutting)
a
a
a
a
PWLN
^ C008
^ C021
KAPR=6330'
7230'
KAPR=90
DCLN
DWLN
KAPR
KAPR
PDJN
PTGN
^ C010
^ C016
New double clamp type.

Holds inserts securely.
Excellent cutting edge
tolerance.
Economical negative
insert.
Small insert series.
16 x 16 x 100 25 x 25 x 150
20 x 20 x 125 32 x 25 x 170
^ C008
DOUBLE
CLAMP
Holder
KAPR=93
External Turning
Shank Size
(H x W x L)
KAPR
LL Holder
External Turning
Copying
^ C021
DDJN
^ C010
DVJN
^ C018
DVVN
^ C019
DTGN
^ C016
Double clamp holder

type.
Holds inserts securely.
Suitable for heavy
cutting.
Negative insert.
32 x 32 x 170
40 x 40 x 200
MCLN
^ C009
WP Holder
a
a
a
Double clamp holder

type.
Simple insert exchange.
Economical negative
insert.
20 x 20 x 125
25 x 25 x 150
MTJN
^ C017
SP Holder
a
a
Screw-on type.
Miniature holder with
7positive insert.
8 x 8 x 60
10 x 10 x 70
12 x 12 x 80
16 x 16 x 100
20 x 20 x 125
25 x 25 x 150
SCLC
^ C022
C002
SDJC
^ C023
SVJC
^ C028
SDNC
^ C023
SVVC
^ C028
STGC
^ C027
PCBN
PSBN
^ C012
PSTN
^ C013
PSDN
^ C014
Special Design
KAPR
PSSN
^ C013
PSKN
^ C015
PTFN
^ C017
PDHN
^ C011
PRGC
^ C024
ue
ee
EXTERNAL TURNING
PSIR
Specialised
KAPR
PSIR
Operation Efficiency
Selection Standard
Clamp Rigidity
KAPR
^ C009
External Turning,
Copying
KAPR=60 KAPR=45 KAPR=45 PSIR=15 PSIR=0 -1 PSIR=10
PSIR
KAPR
Facing,
Copying
Facing
Economical
KAPR=75
External Turning,
Facing, Chamfering
Low Cutting Resistance

(Sharpness)
External Turning,
Chamfering
External Turning
PRDC
^ C024
DVPN
^ C020
e
MSBN
^ C012
MSSN
^ C014
ee
u
SSSC
^ C026
SVPC
^ C029
SRGC
^ C025
SRDC
^ C025
(Note) e : 1st recommendation. u : 2nd recommendation.
C003
CLASSIFICATION
External Turning,
Facing
EXTERNAL TURNING
Features
Tool Holder
KAPR=99 95
MP Holder
KAPR=93
KAPR
a
a
a
Screw-on type.
25 rhombic shape insert.
Possible to machine a
face relief with up to 60
inclination.
16 x 16 x 100
20 x 20 x 125
25 x 25 x 150
a
a
a
Pin lock type.

35rhombic shape insert.
Suitable for recessing.
20 x 20 x 125
25 x 25 x 150
PVJN
a
a
SDJE
TL Holder
a
a
Taper lock type

Excellent finished surface
with round shape insert.
20 x 20 x 125
25 x 25 x 150
32 x 25 x 170
SMALL
TOOLS
(Tools for front turning)
a
a
Screw-on type.
Tools to be equipped on
gang type tool posts.
Miniature holder with
7positive insert.
8 x 8 x 125
10 x 10 x 125
12 x 12 x 150
16 x 16 x 150
SCLC-SM
^ D008
a
a
a
C004
7230'
KAPR=90
KAPR
PVVN
^ C019
Screw-on type.
20positive insert.
(35rhombic shape
insert is 15)
High rake and good
sharpness.
16 x 16 x 100
20 x 20 x 125
25 x 25 x 150
^ C032
SMALL
TOOLS
(Tools for back turning)
KAPR=6230'
KAPR
^ C018
AL Holder
External Turning
Shank Size
(H x W x L)
KAPR
Profile Holder
External Turning,
Copying
Screw-on type.
Tools to be equipped on
gang type tool posts.
High rigidity due to designing of
vertical insert. (BTA/CTB type)
Back machining.
(BTA/CTB type)
8 x 10 x 120
10 x 10 x 120
12 x 12 x 120
16 x 16 x 120
SVJD
^ C034
SDNE
^ C032
SDJC-SM SVJB-SM SDNC-SM SVVB-SM

^ D009
^ D010
^ D009
^ D011
STGE
^ C033
SCAC-SM
^ D008
PSIR=10
PSIR
Special Design
PSIR
KAPR
KAPR
KAPR
PSIR
EXTERNAL TURNING
PSIR=0 -1
Specialised
PSIR=2730'
Selection Standard
Operation Efficiency
KAPR=45
External Turning,
Copying
Clamp Rigidity
KAPR=95 KAPR=75
Facing,
Copying
Facing
Low Cutting Resistance

(Sharpness)
External Turning,
Chamfering
Economical
External Turning
ee
SXZC
^ C030
PVPN
^ C020
STFE
^ C033
TLHR
^ C035
u
SVLP-SM
^ D010
SVPP-SM
^ D011
Special Design
u
BTAH
^ D012
CTBH
^ D013
BTVH
^ D014
(Note) e : 1st recommendation. u : 2nd recommendation.
C005
IDENTIFICATION
y LL Type, Double Clamp Type,
EXTERNAL TURNING
SP Type, Profile Holder, AL Type
P
zClamp Structure
cCutting Angle
L
c
vInsert Clearance
N
v
R
b
bHand of Tool
25
25
mTool Length
(mm)
Double Clamp Type
90Without Offset
7Positive
Right Hand
Wedge Lock Type

M
Multiple Clamp Type
75
Negative
Left Hand
60
45Neutral
20Positive
Neutral
70
Lever Lock Type
60
80
P
S
Screw-on Type
xInsert Shape
C
Rhombic 80
Rhombic 55
Round
Square
Triangular
Rhombic 35
Trigon
X Special Design
C006
90
100
90With Offset
125
10730
150
93
75
95
6230
11730
105
45
60
7230
Special
nTool Size (mm)
(Height and Width)
170
180
200
12
M
m
,Cutting Edge Length (mm)

Insert Shape
Inscribed
Circle Square Triangular Round Rhombic Rhombic Rhombic
80 55 35
6.00
06
6.35
11
06
07
11
7.94
13
8.00
08
9.525
09
16
09
11
16
10.00
10
12.00
12
12.70
12
22
12
15
08
10
10
12
12
16
16
15.875
15
27
16
20
20
16.00
16
25
25
19.05
19
19
32
32
20.00
20
25.00
25
25.40
25
32.00
32
METHOD OF HOLDING
Structure
Lever Lock
(LL HOLDER)
zClamp Screw
xLever
cShim
vShim Pin
bInsert
v
c
x
v
x
Double Clamp
DOUBLE CLAMP
HOLDER
zShim
xShim Pin
cSpring
vClamp Bridge
bClamp Screw
nInsert
z
x
Multiple Clamp
DOUBLE CLAMP
HOLDER
(For heavy cutting)
v c
zShim
xShim Pin
cClamp Screw
vClamp Bridge
bInsert
b
z
x
Wedge Lock
(WP HOLDER)
bv
c
Two action double

clamp
(PROFILE HOLDER)
b
c
Screw-on
SP HOLDER
AL HOLDER
EXTERNAL TURNING
Type (Holder)
c
x
z
c
x
z
n
b
zShim
xShim Pin
cPlate
vSpring
bClamp Bridge
nClamp Screw
mInsert
v
c
x
z
zInsert
xClamp Screw (1)
cSpring
vClamp Bridge
bClamp Screw (2)
x
z
b
v
c
zInsert
xClamp Screw
Pin lock
(MP HOLDER)
b
x
c
z v
zLock Pin
xShim
cStop Ring
vLock Screw
bInsert
b
z
x
c
v
C007
CN TOOL HOLDERS
ooINSERTS
PCLN
LL type
WF
EXTERNAL TURNING
Order Number
Medium
MK
(12,16,19)
RP
Right hand tool

holder shown. (09,12,16,19)
LF
09T3pp
16
16 100 22
16
(12,16,19)
Medium to Rough Stainless
CBN
MS
(12)
(12,16,19)
Dimensions (mm)
Insert Number
R L
Standard
6
H
Stock
Medium
MP
(12)
Medium
LF
HF
95
Light
LP
(12)
95
LH
6
Finish
FH
External turning,
Facing
(12)
Shim
Pin
Clamp
Lever
20 LLSCN3T3
LLP13
LLCL13
LLCS106 HKY25R
LH HF WF
Shim
Clamp
Screw
Wrench
PCLNR/L1616H09
a a
PCLNR/L2020K09
a a
09T3pp
20
20 125 22
20
25 LLSCN3T3
LLP13
LLCL13
LLCS106 HKY25R
PCLNR/L2525M09
a a
09T3pp
25
25 150 22
25
32 LLSCN3T3
LLP13
LLCL13
LLCS106 HKY25R
PCLNR/L2020K12
a a
1204pp
20
20 125 28
20
25 LLSCN42
LLP14
LLCL14
LLCS108 HKY30R
PCLNR/L2525M12
a a
1204pp
25
25 150 28
25
32 LLSCN42
LLP14
LLCL14
LLCS108 HKY30R
PCLNR/L3225P12
a a
1204pp
32
25 170 28
32
32 LLSCN42
LLP14
LLCL14
LLCS108 HKY30R
PCLNR/L3232P16
a a
1606pp
32
32 170 32
32
40 LLSCN53
LLP15
LLCL25
LLCS508 HKY30R
PCLNR/L3232P19
a a
1906pp
32
32 170 40
32
40 LLSCN63
LLP16
LLCL16
LLCS310 HKY40R
CNMG
CNMA
CNMG
CNMM
CNGG
Clamp Torque (N m) : LLCS106=2.2, LLCS108=3.3, LLCS508=3.3, LLCS310=7.0
DCLN
DOUBLE CLAMP type
95
LH
Finish
FH
Light
Medium
LP
MP
Medium
MK
WF
External turning,
Facing
LF
(12)
(12)
(12)
(12)
Medium
Medium to Rough
Stainless
CBN
Standard
RP
MS
Order Number
Stock
DCLNR/L2020K09
*
*
09T3pp
a a
a a
DCLNR/L2525M09
a a
DCLNR/L2020K12
a a
DCLNR/L2525M12
a a
DCLNR/L3225P12
a a
CNMG
CNMA
CNMG
CNMM
CNGG
09T3pp
Right hand tool

holder shown.
16
20
LF
LH HF WF
16 100 25
20 125 25
16
20
(09,12)
Dimensions (mm)
Insert Number
R L
DCLNR/L1616H09
HF
95
(12)
(12)
Shim
(12)
Shim
Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
20
LLSCN3T3
(LLSCN33)
25
LLSCN3T3
(LLSCN33)
LLSCN3T3
(LLSCN33)
09T3pp
25
25 150 25
25
32
1204pp
20
20 125 29
20
25 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
1204pp
25
25 150 29
25
1204pp
32
25 170 29
32
1 Clamp Torque (N m) : DC0520T=3.5, DC0621T=5.0

2 Please use shim no. LLSCN33 with 3.18mm thick inserts. When using 3.18mm thick inserts, shim should be ordered separately.
C008
PCLN type inserts

DCLN type inserts
A092 A097
A092 A097
CBN & PCD inserts

B022 B024, B055

A070
Medium
For heavy cutting MH
Order Number
MCLNR3232P19
MCLNR4040R19
Medium to Rough
RP
(19)
(19)
(19)
(19)
Heavy
Heavy
Heavy
M Class
HZ
HX
Right hand tool

holder only.
(19)
HV
(19)
(19)
Dimensions (mm)
Insert Number
CNMG
CNMM
CNMA
LF
HF
Stock
Medium
MS
WF
95
LH
95
Medium
Standard
LF
1906pp
32
32 170 36
32
1906pp
40
40 200 36
40
(19)
Shim
Shim Pin
Clamp
Bridge
Clamp
Screw
Wrench
40
MSCN63
MP6
CKW6
LS25
HKY40R
50
MSCN63
MP6
CKW6
LS25
HKY40R
LH HF WF
EXTERNAL TURNING
MCLN
DOUBLE CLAMP type
External turning,
Facing
Clamp Torque (N m) : LS25=8.2
PCBN
LL type
75
LH
LF
Order Number
Stock
R L
PCBNR/L2020K12
a a
PCBNR/L2525M12
a a
Medium
MK
(12)
(12)
(12)
Medium to Rough
Stainless
Standard
RP
(12)
LF
1204pp
20
20 125 28
20
1204pp
25
25 150 25
25
Medium
MP
(12)
MS
(12)
(12)
Dimensions (mm)
Insert Number
CNMA
CNMG
CNMM
CNGG
Light
LP
Medium
Right hand tool

holder shown.
75
HF
6
6
Finish
FH
WF
External turning
Shim
Shim
Pin
Clamp
Lever
Clamp
Screw
Wrench
17
LLSCN42
LLP14
LLCL14
LLCS108
HKY30R
22
LLSCN42
LLP14
LLCL14
LLCS108
HKY30R
LH HF WF
* Clamp Torque (N m) : LLCS108=3.3
MCLN type inserts

PCBN type inserts
CBN & PCD inserts
A094 A097
A094 A097
B022 B024, B055

SPARE PARTS
TECHNICAL DATA
A070
P001
Q001
C009
DN TOOL HOLDERS
ooINSERTS
PDJN
LL type
WF
EXTERNAL TURNING
(15)
RP
MS
Stock
a a
PDJNR/L2525M15
a a
PDJNR/L3225P15
a a
(15)
CBN
R/L
1504pp
1504pp
1504pp
(15)
Dimensions (mm)
Insert Number
DNMA
DNMG
DNMM
DNMX
DNGA
DNGG
Right hand tool

holder shown.
20
25
32
LF
25 150 35
25 170 35
20
25
32
(15)
(15)
Shim
Shim
Pin
Clamp
Lever
Clamp
Screw
Wrench
25
LLSDN43
(LLSDN42)
LLP14
LLCL24
LLCS108
HKY30R
32
LLSDN43
(LLSDN42)
LLP14
LLCL24
LLCS108
HKY30R
32
LLSDN43
(LLSDN42)
LLP14
LLCL24
LLCS108
HKY30R
LH HF WF
20 125 35
(15)
1 Clamp Torque (N m) : LLCS108=3.3

2 Please use shim no. LLSDN42 with 6.35mm thick inserts. When using 6.35mm thick inserts, shim should be ordered separately.
DDJN
External turning,
Copying
DOUBLE CLAMP type
Finish
FH
Light
LP
WF
(15)
93
LH
93
Medium
MK
(15)
LF
RP
MS
(15)
(15)
G Class
CBN
R/L
Stock
DDJNR/L1616H11
a a
DDJNR/L2020K11
a a
DDJNR/L2525M11
a a
DDJNR/L3225P11
a a
a a
DDJNR/L2525M15
a a
DDJNR/L3225P15
a a
DNMG
DNMX
DNMA
DNMG
DNMM
DNMX
DNGA
DNGG
Right hand tool

holder shown.
(15)
(15)
*
Shim
Pin
Clamp
Bridge
Clamp
Screw
1104pp
16
16 100 28
16
20 LLSDN32 LLP23 DCK2211 DCS2 DC0520T TKY15F
1104pp
20
20 125 28
20
1104pp
25
25 150 28
25
1104pp
32
25 170 28
32
1504pp
20
20 125 37
20
25
LLSDN43
(LLSDN42)
32
LLSDN43
(LLSDN42)
32
LLSDN43
(LLSDN42)
1504pp
25
32
LH HF WF
(15)
1504pp
LF
(15)
Dimensions (mm)
Insert Number
R L
DDJNR/L2020K15
Medium
MP
HF
Order Number
*
*
(15)
G Class
*
*
Medium
MK
R L
PDJNR/L2020K15
Medium
MP
LF
6
HF
Order Number
Light
LP
(15)
93
LH
93
Finish
FH
External turning,
Copying
25 150 37
25 170 37
25
32
Shim
Spring
Wrench

2 Please use shim no. LLSDN42 with 6.35mm thick inserts. When using 6.35mm thick inserts, shim should be ordered separately.
C010
PDJN type inserts

DDJN type inserts
A098 A103
A098 A103
CBN & PCD inserts

B025 B027, B055

A070
Medium
Medium
MK
WF
MP
(15)

RP
LF
MS
(15)
(15)
G Class
CBN
R/L
Stock
a a
PDHNR/L2525M15
a a
PDHNR/L3225P15
a a
H
DNMA
DNMG
DNMM
DNGA
DNGG
Dimensions (mm)
Insert Number
R L
PDHNR/L2020K15
Right hand tool

holder shown.
HF
Order Number
Light
LP
(15)
10730
LH
107
30
Finish
FH
LF
LH HF WF
(15)
2
(15)
(15)
(15)
Shim
Shim Pin
Clamp
Lever
LLP14
LLCL24
LLCS108 HKY30R
LLP14
LLCL24
LLCS108 HKY30R
LLP14
LLCL24
LLCS108 HKY30R
1504pp
20
20 125 34
20
25
1504pp
25
25 150 34
25
32
LLSDN43
(LLSDN42)
LLSDN43
(LLSDN42)
1504pp
32
25 170 34
32
32
LLSDN43
(LLSDN42)
Clamp
Screw
Wrench
EXTERNAL TURNING
PDHN
LL type
Facing, Copying
*12 Clamp
Please use shim no. LLSDN42 with 6.35mm thick inserts. When using 6.35mm thick inserts, shim should be ordered separately.
*
PDHN type inserts

CBN & PCD inserts
A098 A103
B025 B027, B055
A070
SPARE PARTS
TECHNICAL DATA
P001
Q001
C011
SN TOOL HOLDERS
ooINSERTS
PSBN
LL type
B
75
LH
Light
Medium
LP
MP
(09,12)
(12)
LF
RP
Right hand tool

holder shown.
75
Order Number
Finish
FH
MS
Medium
MK
(12,15,19)
(12)
G Class
CBN
R/L
HF
EXTERNAL TURNING
WF
External turning
Stock
a a
PSBNR/L1616H09
a a
PSBNR/L2020K12
a a
PSBNR/L2525M12
a a
PSBNR/L2525M15
a a
PSBNR/L3232P19
a a
SNMA
SNMG
SNMM
SNGA
SNGG
(12,15,19)
(09,12)
(12)
Dimensions (mm)
Insert Number
R L
PSBNR/L1212F09
(12)
Shim
Shim
Pin
Lever
Spring
HLS2
LLCL13S LLCS105 HKY20R
13 LLSSN33 LLP23
20
17 LLSSN42 LLP14
LF
0903pp
12
12
80 20
12
13
0903pp
16
16 100 22
16
1204pp
20
LH HF WF
20 125 28
Clamp
Lever
Clamp
Screw
Wrench
1204pp
25
25 150 25
25
22 LLSSN42 LLP14
1506pp
25
25 150 33
25
22 LLSSN53 LLP15
1906pp
32
32 170 40
32
27 LLSSN63 LLP16
* Clamp Torque (N m) : LLCS105=1.5, LLCS106=2.2, LLCS108=3.3, LLCS508=3.3, LLCS310=7.0
MSBN
DOUBLE CLAMP type
Medium
75
LH
Order Number
Stock
MSBNR3232P19
MSBNR4040R19
SNMG
SNMM
SNMA
Medium
MS
Medium to Rough
RP
(19)
(19)
(19)
(19)
Heavy
Heavy
Heavy
M Class
HZ
Right hand tool

holder only.
HX
(19)
HV
(19)
(19)
Dimensions (mm)
Insert Number
LF
HF
75
Medium
Standard
WF
External
turning
LF
1906pp
32
32 170 41
32
1906pp
40
40 200 41
40
(19)
Shim
Shim Pin
Clamp
Bridge
Clamp
Screw
Wrench
27
MSSN63
MP6
CKW6
LS25
HKY40R
35
MSSN63
MP6
CKW6
LS25
HKY40R
LH HF WF
* Clamp Torque (N m) : LS25=8.2
C012
PSBN type inserts

MSBN type inserts
A105 A109
A106 A109
CBN & PCD inserts

B028, B056
A070
Order Number
Stock
PSTNR/L1616H09
LF
RP
a a
PSTNR/L2020K12
a a
PSTNR/L2525M12
a a
SNMA
SNMG
SNMM
SNGA
SNGG
MS
Right hand tool

holder shown.
Medium
MK
(12)
(12)
(12)
G Class
CBN
R/L
(12)
(09,12)
LF
(12)
Dimensions (mm)
Insert Number
R L
(12)
60
Medium
MP
WF
6
Light
LP
(09,12)
60LH
HF
Finish
FH
Shim
Shim
Pin
Clamp
Lever
Clamp
Screw
Wrench
13
LLSSN33
LLP23
LLCL13
LLCS106
HKY25R
20
17
LLSSN42
LLP14
LLCL14
LLCS108
HKY30R
25
22
LLSSN42
LLP14
LLCL14
LLCS108
HKY30R
LH HF WF
0903pp
16
16 100 20
16
1204pp
20
20 125 25
1204pp
25
25 150 25
EXTERNAL TURNING
PSTN
LL type
External turning,
Chamfering
Clamp Torque (N m) : LLCS106=2.2, LLCS108=3.3
PSSN
LL type
LF
PSSNR/L1616H09
a a
PSSNR/L2020K12
a a
PSSNR/L2525M12
a a
PSSNR/L3232P15
a a
PSSNR/L3232P19
a a
Medium
MK
(12)
MS
(12)
(12,15,19)
(12)
G Class
CBN
R/L
(12,15,19)
(09,12)
(12)
Dimensions (mm)
Insert Number
Shim
Pin
Clamp
Lever
Clamp
Screw
Wrench
0903pp 16 16 100 22 16 20 (14) LLSSN33
LLP23
LLCL13
LLCS106
HKY25R
1204pp 20 20 125 31 20 25 (17) LLSSN42
LLP14
LLCL14
LLCS108
HKY30R
1204pp 25 25 150 31 25 32 (24) LLSSN42
LLP14
LLCL14
LLCS108
HKY30R
1506pp 32 32 170 34 32 40 (29) LLSSN53
LLP15
LLCL25
LLCS508
HKY30R
1906pp 32 32 170 40 32 40 (27) LLSSN63
LLP16
LLCL16
LLCS310
HKY40R
SNMA
SNMG
SNMM
SNGA
SNGG
RP
Right hand tool

holder shown.
R L
Medium
MP
Stock
Light
LP
(09,12)
45
LH
45
Order Number
Finish
FH
WF
WF2
External turning,
Facing, Chamfering
LF LH HF WF WF2
Shim
(Note) When facing or chamfering only and using insert with right or left hand breaker, please use left hand insert for right hand
holder and right hand insert for left hand holder.
PSTN type inserts

PSSN type inserts
CBN & PCD inserts
A105 A109
A105 A109
B028, B056

SPARE PARTS
TECHNICAL DATA
A070
P001
Q001
C013
SN TOOL HOLDERS
ooINSERTS
MSSN
DOUBLE CLAMP type
Medium
45
EXTERNAL TURNING
LH
Stock
MSSNR3232P19
MSSNR4040R19
Rough
RP
(19)
(19)
(19)
(19)
Heavy
Heavy
M Class
HX
Right hand tool

holder only.
(19)
HV
(19)
(19)
(19)
Dimensions (mm)
Insert Number
Shim Pin
Clamp
Bridge
Clamp
Screw
Wrench
1906pp 32 32 170 44 32 40 27 MSSN63
MP6
CKW6
LS25
HKY40R
1906pp
MP6
CKW6
LS25
HKY40R
SNMG
SNMM
SNMA
Medium
MS
Heavy
HZ
LF
45
Order Number
Medium
Standard
WF
WF2
External turning,
Facing, Chamfering
LF LH HF WF WF2
Shim
40 40 200 44 40 50 37 MSSN63
Clamp Torque (N m) : LS25=8.2
PSDN
LL type
45
H
Finish
FH
Light
Medium
LP
MP
Medium
MK
WF
External turning,
Chamfering
(09,12)
LH
(12)
LF
RP
MS
(12)
(12)
G Class
CBN
R/L
45
Order Number
Stock
PSDNN1212F09
PSDNN1616H09
PSDNN2020K12
PSDNN2525M12
PSDNN3225P12
(12)
(09,12)
(12)
Dimensions (mm)
Insert Number
SNMA
SNMG
SNMM
SNGA
SNGG
(12)
Shim
Shim
Pin
Lever
Spring
HLS2
8.0 LLSSN33 LLP23
20
20 125 28 20 10.0 LLSSN42 LLP14
1204pp
25
25 150 28 25 12.5 LLSSN42 LLP14
1204pp
32
25 170 28 32 12.5 LLSSN42 LLP14
LF LH HF WF
0903pp
12
12
80 20 12
0903pp
16
16 100 22 16
1204pp
6.0
Clamp
Lever
Clamp
Screw
Wrench
Clamp Torque (N m) : LLCS105=1.5, LLCS106=2.2, LLCS108=3.3
C014
MSSN type inserts

PSDN type inserts
A106 A109
A105 A109
CBN & PCD inserts

B028, B056
A070
75
(09,12)
LH
LF
Stock
Right hand tool

holder shown.
R L
PSKNR/L1616H09
a a
PSKNR/L2020K12
a a
PSKNR/L2525M12
a a
(12)
MS
(12)
(12)
G Class
CBN
R/L
(12)
(12)
(09,12)
LF
(12)
Dimensions (mm)
Insert Number
SNMA
SNMG
SNMM
SNGA
SNGG
Medium
MK
HF
Order Number
Medium
MP

RP
Light
LP
WF
75
Finish
FH
Shim
Shim
Pin
Clamp
Lever
Clamp
Screw
Wrench
20
LLSSN33
LLP23
LLCL13
LLCS106
HKY25R
20
25
LLSSN42
LLP14
LLCL14
LLCS108
HKY30R
25
32
LLSSN42
LLP14
LLCL14
LLCS108
HKY30R
LH HF WF
0903pp
16
16 100 20
16
1204pp
20
20 125 25
1204pp
25
25 150 25
EXTERNAL TURNING
PSKN
LL type
Facing
(Note) When using insert with right or left hand breaker, please use left hand insert for right hand holder and right hand insert for left
hand holder.
PSKN type inserts

CBN & PCD inserts
A105 A109
B028, B056
A070
SPARE PARTS
TECHNICAL DATA
P001
Q001
C015
TN TOOL HOLDERS
ooINSERTS
PTGN
LL type
Finish
Light
FH
MP
91
LH
RP
LF
HF
Stock
MS
Right hand tool

holder shown.
LF
LH HF WF
PTGNR/L1010E11
a a
1103pp
10
10
70 17
10
12
PTGNR/L1212F11
a a
1103pp
12
12
80 17
12
16
PTGNR/L1616H16
a a
PTGNR/L2020K16
a a
PTGNR/L2525M16
a a
PTGNR/L2525M22
a a
PTGNR/L3225P22
PTGNR/L3232P27
1604pp
TNMA
TNMG
TNMM
TNGA
TNGG
1604pp
16
20
16 100 22
20 125 22
16
20
(16)
Dimensions (mm)
Insert Number
R L
(16,22,27)
(16,22)
G Class
CBN
R/L
(16,22)
(11,16,22)
(16)
Clamp
Lever
Shim
Shim
Pin
Lever
Spring
Clamp
Screw
HLS1
LLCL12S LLCS105 HKY20F
Wrench
HLS1
LLCL12S LLCS105 HKY20F
20
LLSTN32
LLP13
(LLSTN33) (LLP23)
25
LLSTN32
LLP13
(LLSTN33) (LLP23)
LLSTN32
LLP13
(LLSTN33) (LLP23)
1604pp
25
25 150 22
25
32
2204pp
25
25 150 28
25
32 LLSTN42 LLP14
a a
2204pp
32
25 170 28
32
32 LLSTN42 LLP14
a a
2706pp
32
32 170 35
32
40 LLSTN53 LLP15
1 Clamp Torque (N m) : LLCS105=1.5, LLCS106=2.2, LLCS206=2.2, LLCS108=3.3, LLCS508=3.3

PTGNR/L1010E11 PTGNR/L1212F11 Clamp Torque (N m) : LLCS105=1.0
2 Please use shim no. LLSTN33 and shim pin no. LLP23 with 3.18mm thick inserts. When using 3.18mm thick inserts, shim and shim pin
should be ordered separately.
DTGN
DOUBLE CLAMP type
Order Number
DTGNR/L1616H16
a a
DTGNR/L2020K16
a a
DTGNR/L2525M16
(16)
LF
a a
TNMA
TNMG
TNMM
TNGA
TNGG
Right hand tool

holder shown.
LF
LH HF WF
Shim
1604pp
16
16 100 25
16
20
1604pp
20
20 125 25
20
25
32
LLSTN32
(LLSTN33)
25
25 150 25
25
MS
(16)
2
LLSTN32
(LLSTN33)
LLSTN32
(LLSTN33)
1604pp
Medium
MP
(16)
RP
Dimensions (mm)
Insert Number
R L
Light
LP
91
LH
HF
Stock
Finish
FH
Medium
MK
WF
External turning
91
*
*
Medium
MK
Order Number
*
*
(16)
EXTERNAL TURNING
(11,16)
91
Medium
LP
WF
External turning
(16)
(16)
G Class
CBN
R/L
(16)
(16)
Shim
Pin
Clamp
Bridge
Spring
Clamp
Screw
(16)
1
Wrench
1 Clamp Torque (N m) : DC0520T=3.5

2 Please use shim no. LLSTN33 with 3.18mm thick inserts. When using 3.18mm thick inserts, shim should be ordered separately.
C016
PTGN type inserts

DTGN type inserts
A110 A115
A110 A115
CBN & PCD inserts

B030, B031, B056

A070
91
Stock
a a
PTFNR/L2020K16
a a
PTFNR/L2525M16
a a
PTFNR/L2525M22
a a
RP
Right hand tool

holder shown.
MS
(16)
2
(16,22)
(16,22)
G Class
CBN
R/L
1604pp
1604pp
16
20
LF
20 125 22
16
20
(16,22)
(16)
Clamp
Screw
Wrench
20
LLSTN32 LLP13
(LLSTN33) (LLP23)
LLCL13
LLCS106
HKY25R
25
LLSTN32 LLP13
(LLSTN33) (LLP23)
LLCL13
LLCS106
HKY25R
LLSTN32 LLP13
(LLSTN33) (LLP23)
1604pp
25
25 150 22
25
32
2204pp
25
25 150 28
25
32
Shim
Pin
Clamp
Lever
LH HF WF
16 100 22
(16,22)
Dimensions (mm)
Insert Number
TNMA
TNMG
TNMM
TNGA
TNGG
Medium
MK
R L
PTFNR/L1616H16
(16)
LF
HF
Order Number
Medium
MP
(16)
LH
Light
LP
WF
91
Finish
FH
Shim
LLSTN42
LLP14
LLCL13
LLCS206
HKY25R
LLCL14
LLCS108
HKY30R
EXTERNAL TURNING
PTFN
LL type
Facing
hand holder.
1 Clamp Torque (N m) : LLCS106=2.2, LLCS206=2.2, LLCS108=3.3
2 Please use shim no. LLSTN33 and shim pin no. LLP23 with 3.18mm thick inserts. When using 3.18mm thick inserts, shim should be ordered
separately.
*
*
MTJN
WP type
Finish
FH
Light
LP
WF
(16)
93
LH
LF
Order Number
Stock
a a
MTJNR/L2525M16N
a a
MTJNR/L2525M22N
a a
TNMA
TNMG
TNMM
TNGA
TNGG
RP
MS
(16,22)
(16,22)
G Class
CBN
R/L
Right hand tool

holder shown.
(16)
(16,22)
Dimensions (mm)
Insert Number
R L
MTJNR/L2020K16N
Medium
MK
HF
(16)
93
Medium
MP
External turning,
Copying
LF
LH HF WF
1604pp
20
20 125 31
20
25
1604pp
25
25 150 31
25
32
2204pp
25
25 150 38
25
32
(16,22)
(16)
Shim Clamp Side Lock Spring Clamp Wrench

Pin Bridge Plate
Screw
WPSTN33 CCP33 CCK13 CPT13 MES2 SLCS105 HKY25R
HKY40R
HKY40R
HKY40R
Shim
Clamp Torque (N m) : SLCS105=7.0, SLCS106=7.0
MTJN type inserts

PTFN type inserts
CBN & PCD inserts
A110 A115
A110 A115
B030, B031, B056
A070
SPARE PARTS
TECHNICAL DATA
P001
Q001
C017
VN TOOL HOLDERS
ooINSERTS
PVJN
MP type
WF
93
LH
6
13
HF
LF
13
Order Number
Stock
R L
PVJNR/L2020K16
a a
PVJNR/L2525M16
a a
Medium
MP
Medium
MK
(16)
(16)
(16)
(16)
Medium
Stainless
G Class
CBN
Right hand tool

holder shown.
MS
(16)
R/L
(16)
Dimensions (mm)
Insert Number
H
VNMG
VNGA
VNGG
Light
LP
Standard
H
EXTERNAL TURNING
93
Finish
FH
External turning,
Copying
LF
LH HF WF
1604pp
20
20 125 32
20
25
1604pp
25
25 150 38
25
32
Shim
(16)
(16)
PV321
PV322
PV323
P11S
HSP05008C
E03
HKY25R
P11S
HSP05008C
E03
HKY25R
DVJN
DOUBLE CLAMP type
93
LH
93
Light
Medium
LP
MP
Medium
MK
LF
(16)
(16)
(16)
(16)
Medium
Stainless
G Class
CBN
Standard
MS
R/L
13
Stock
a a
DVJNR/L2525M16
a a
VNMG
VNGA
VNGG
Right hand tool

holder shown.
(16)
(16)
(16)
Dimensions (mm)
Insert Number
R L
DVJNR/L2020K16
HF
Order Number
Finish
FH
WF
External turning,
Copying
LF
LH HF WF
Shim
Pin
Clamp
Bridge
Clamp
Screw
(16)
1604pp
20
20 125 41
20
1604pp
25
25 150 41
25
Shim
Spring
Wrench
C018
PVJN type inserts

DVJN type inserts
A116 A118
A116 A118
CBN & PCD inserts

B032, B033, B057

A070
Finish
Light
FH
72
30
MP
(16)
(16)
(16)
(16)
LH
Medium
Stainless
G Class
CBN
LF
Standard
MS
R/L
HF
16
Stock
DVVNN2020K16
DVVNN2525M16
VNMA
VNMG
VNGA
VNGG
(16)
(16)
Dimensions (mm)
Insert Number
H
Medium
MK
7230
(16)
Order Number
Medium
LP
WF
DOUBLE CLAMP type
LF
LH HF WF
1604pp 20 20 125 44 20 10
1604pp
Shim
Pin
Shim
Clamp
Bridge
Spring
Clamp
Screw
(16)
Wrench
EXTERNAL TURNING
DVVN
External turning,
Copying
DCSVN32 LLP13 DCK3113 DCS2 DC0520T TKY15F
25 25 150 44 25 12.5 DCSVN32 LLP13 DCK3113 DCS2 DC0520T TKY15F
Clamp Torque (N m) : DC0520T=3.5
PVVN
MP type
7230
LH
72
30
Finish
FH
LF
(16)
(16)
(16)
Stainless
G Class
CBN
PVVNN2525M16
R/L
HF
PVVNN2020K16
MS
(16)
(16)
Dimensions (mm)
Insert Number
VNMA
VNMG
VNGA
VNGG
Medium
MK
(16)
Standard
16
Stock
Medium
MP
Medium
16
Order Number
Light
LP
WF
External turning,
Copying
LF
LH HF WF
1604pp 20 20 125 38 20 10
1604pp 25 25 150 38 25 12.5
Shim
PV321
PV322
PV323
(16)
(16)

P11S
HSP05008C
E03
HKY25R
P11S
HSP05008C
E03
HKY25R
* Clamp Torque (N m) : HSP05008C=2.5
DVVN type inserts

PVVN type inserts
CBN & PCD inserts
A116 A118
A116 A118
B032, B033, B057

SPARE PARTS
TECHNICAL DATA
A070
P001
Q001
C019
VN TOOL HOLDERS
ooINSERTS
DVPN
DOUBLE CLAMP type
Finish
FH
LH
7
(16)
(16)
(16)
Stainless
G Class
CBN
MS
R/L
13
Stock
DVPNR/L2020K16
a a
DVPNR/L2525M16
a a
VNMG
VNGA
VNGG
Right hand tool

holder shown.
(16)
(16)
(16)
Dimensions (mm)
Insert Number
R L
Medium
MK
(16)
Standard
LF
HF
EXTERNAL TURNING
Order Number
Medium
MP
Medium
11730
117
30
Light
LP
WF
Facing, Copying
LF
LH HF WF
Shim
Pin
Clamp
Bridge
Clamp
Screw
(16)
1604pp
20
20 125 32
20
1604pp
25
25 150 32
25
Shim
Spring
Wrench
PVPN
MP type
Facing, Copying
Finish
FH
Light
LP
Medium
MP
Medium
MK
WF
2730
11730
LH
117
30
Order Number
Stock
PVPNR/L2020K16
a a
PVPNR/L2525M16
a a
VNMG
VNGA
VNGG
(16)
(16)
G Class
CBN
Right hand tool

holder shown.
MS
(16)
R/L
(16)
Dimensions (mm)
Insert Number
R L
(16)
Stainless
Standard
LF
13
HF
10
(16)
Medium
LF
LH HF WF
1604pp
20
20 125 32
20
25
1604pp
25
25 150 32
25
32
Shim
PV321
PV322
PV323
(16)
(16)

P11S
HSP05008C
E03
HKY25R
P11S
HSP05008C
E03
HKY25R
* Clamp Torque (N m) : HSP05008C=2.5
C020
DVPN type inserts

PVPN type inserts
A116 A118
A116 A118
CBN & PCD inserts

B032, B033, B057

A070
WN TOOL HOLDERS
ooINSERTS
Light
Medium
MP
WF
SH
(06)
95
LH
LF
MS
6 6
Order Number
Stock
PWLNR/L1616H06
*
*
06T3pp
a a
PWLNR/L2020K06
a a
PWLNR/L2525M06
a a
WNMG
06T3pp
06T3pp
Dimensions (mm)
Insert Number
R L
16
20
25
LF
16
20 125 22
20
25 150 25
25
*1
Shim
Shim
Pin
20
LLSWN3T3
(LLSWN32)
LLP13
25
LLSWN3T3
(LLSWN32)
LLP13
32
LLSWN3T3
(LLSWN32)
LLP13
LH HF WF
16 100 22
(06)
Clamp
Lever
Clamp
Screw
Wrench

2 Please use shim no. LLSWN32 with 4.76mm thick inserts. When using 4.76mm thick inserts, shim should be ordered separately.
DWLN
DOUBLE CLAMP type
95
LH
DWLNR/L2020K06
Medium
MP
Medium
MK
(08)
(08)
(06,08)
(08)
Medium
Medium to Rough
Stainless
CBN
Standard
LF
06T3pp
a a
DWLNR/L2525M06
a a
DWLNR/L2020K08
a a
DWLNR/L2525M08
a a
DWLNR/L3225P08
a a
WNMG
WNMA
WNMG
06T3pp
Dimensions (mm)
Insert Number
a a
Right hand tool

holder shown.
HF
Stock
R L
DWLNR/L1616H06
Light
LP
RP
MS
95
Order Number
Finish
FH
WF
External turning,
Facing
*
*
Right hand tool

holder shown.
HF
95
(06)
Stainless
EXTERNAL TURNING
PWLN
LL type
External turning,
Facing
16
20
LF
LH HF WF
16 100 25
20 125 25
16
20
(08)
2
Shim
(08)
Shim
Pin
Clamp
Bridge
(06,08)
*1
Spring Clamp
Screw
Wrench
20
LLSWN3T3
(LLSWN32)
25
LLSWN3T3
(LLSWN32)
LLSWN3T3
(LLSWN32)
06T3pp 25
25 150 25
25
32
0804pp
20
20 125 31
20
0804pp
25
25 150 31
25
0804pp
32
25 170 31
32

2 Please use shim no. LLSWN32 with 4.76mm thick inserts. When using 4.76mm thick inserts, shim should be ordered separately.
PWLN type inserts

DWLN type inserts
CBN inserts
A119 A122
A119 A123
B034

SPARE PARTS
TECHNICAL DATA
A070
P001
Q001
C021
CC TOOL HOLDERS
ooINSERTS
SCLC
SP type
LF
HF
Stock
a a
SCLCR/L1010E06
a a
SCLCR/L1212F09
a a
SCLCR/L1616H12
a a
CCET
CCGT
CCMW
CCMT
CCGW
Light
LM
(06,09)
(06,09)
(06,09)
(06,09)
Medium
Flat top
PCD/CBN
(06,09,12)
(06,09,12)
MM
(06,09,12)
0602pp
0602pp
10
09T3pp
1204pp
LF
(06,09,12)
Dimensions (mm)
Insert Number
R L
SCLCR/L0808D06
Light
LP
Medium
MP
Right hand tool holder shown.
Order Number
Finish
FM
EXTERNAL TURNING
95
LH
95
Finish
FP
WF
External turning,
Facing
LH
HF
WF
Clamp Screw
Wrench
60
8.9
10
TS25
TKY08F
10
70
8.9 10
12
TS25
TKY08F
12
12
80 13.6 12
16
TS43
TKY15F
16
16 100 16.7 16
20
TS5
TKY25F
Clamp Torque (N m) : TS25=1.0, TS43=3.5, TS5=7.5
SCLC type inserts
a
C022
CBN & PCD inserts

A126 A130
B039 B041, B059
A070
DC TOOL HOLDERS
ooINSERTS
LF
(07,11)
(07,11)
(07,11)
Medium
Flat top
PCD/CBN
(07,11)
(07,11)
R L
SDJCR/L1010E07
a a
SDJCR/L1212F11
a a
SDJCR/L1616H11
a a
MM
(07,11)
(07,11)
Dimensions (mm)
Insert Number
DCET
DCGT
DCMW
DCMT
DCGW
Light
LM
(07,11)
MP
HF
Stock
Light
LP
Medium
Order Number
Finish
FM
WF
93
LH
93
Finish
FP
0702pp
10
11T3pp
11T3pp
LF
LH
HF
WF
Clamp Screw
Wrench
10
70 12
10
12
TS25
TKY08F
12
12
80 18
12
16
TS43
TKY15F
16
16
100 18
16
20
TS43
TKY15F
EXTERNAL TURNING
SDJC
SP type
External turning,
Copying
Clamp Torque (N m) : TS25=1.0, TS43=3.5
SDNC
SP type
6230
LF
Finish
FM
Stock
SDNCN0808D07
SDNCN1010E07
(07,11)
(07,11)
(07,11)
Medium
Flat top
PCD/CBN
(07,11)
(07,11)
MM
SDNCN1212F11
SDNCN1616H11
LF
HF
(07,11)
Dimensions (mm)
Insert Number
DCET
DCGT
DCMW
DCMT
DCGW
Light
LM
(07,11)
(07,11)
Order Number
Light
LP
Medium
MP
HF
62
30
Finish
FP
WF
External turning,
Copying
WF
Clamp Screw
Wrench
0702pp
60
TS25
TKY08F
0702pp
10
10
70
10
TS25
TKY08F
11T3pp
12
12
80
12
TS43
TKY15F
11T3pp
16
16
100
16
TS43
TKY15F
* Clamp Torque (N m) : TS25=1.0, TS43=3.5
SDJC type inserts

SDNC type inserts
CBN & PCD inserts
A132 A135
A132 A135
B043, B044, B060

SPARE PARTS
TECHNICAL DATA
A070
P001
Q001
C023
RC TOOL HOLDERS
ooINSERTS
PRGC
LL type
WF
(10,12,16,20)
LF
Stock
PRGCR/L2525M10
a a
PRGCR/L2525M12
a a
PRGCR/L2525M16
a a
PRGCR/L3232P20
a a
RCMX
Right hand tool

holder shown.
Dimensions (mm)
Insert Number
R L
HF
EXTERNAL TURNING
LH
Order Number
Medium
External turning,
Facing, Copying
LF
LH
HF WF
Shim
Pin
Clamp
Lever
Clamp
Screw
1003M0
25
25 150 16.7 25
32 LLSRN103 LLP13 LLCL110 LLCS205 HKY20R
1204M0
25
25 150 17.5 25
1606M0
25
25 150 19.9 25
2006M0
32
32 170 23.8 32
Shim
Wrench
* Clamp Torque (N m) : LLCS205=1.5, LLCS106=2.2, LLCS306=2.2, LLCS508=3.3
PRDC
LL type
(10,12,16,20)
LH
LF
Stock
HF
Order Number
Dimensions (mm)
Insert Number
Medium
WF
External turning,
Copying
LF
LH
HF WF
Shim
Shim
Pin
Clamp
Lever
Clamp
Screw
Wrench
PRDCN2020K10
1003M0
20
20 125 23
20 10.0 LLSRN103 LLP13 LLCL110 LLCS205 HKY20R
PRDCN2525M12
1204M0
25
25 150 24
PRDCN3225P12
1204M0
32
25 170 24
PRDCN3225P16
1606M0
32
25 170 28
PRDCN3232P20
2006M0
32
32 170 33
RCMX
PRGC type inserts
a
C024
PRDC type inserts

A137
A137
A070
SRGC
SP type
Medium
Standard
WF
External turning,
Facing, Copying
45
(06,08)
LH
Stock
R L
SRGCR/L1616H06
a a
SRGCR/L1616H08
a a
RCMT
RCGT
Right hand tool

holder shown.
Dimensions (mm)
Insert Number
EXTERNAL TURNING
Order Number
HF
LF
0602pp
16
0803pp
16
LF
LH
HF
WF
Clamp Screw
Wrench
16 100 10
16
20
TS25
TKY08F
16 100 14.5
16
22
TS3
TKY08F
SRDC
SP type
Medium
Standard
WF
External turning,
Copying
(06,08)
LH
Order Number
Stock
SRDCN1616H06
SRDCN1616H08
Dimensions (mm)
Insert Number
RCMT
RCGT
HF
LF
LH
HF
WF
Clamp Screw
Wrench
0602pp
16
16 100 12
LF
16
TS25
TKY08F
0803pp
16
16 100 16
16
TS3
TKY08F
SRGC type inserts

SRDC type inserts
A137
A137
A070
SPARE PARTS
TECHNICAL DATA
P001
Q001
C025
SC TOOL HOLDERS
ooINSERTS
SSSC
SP type
LF
HF
Stock
a a
SSSCR/L1616H09
a a
SCMW
SCMT
Light
LM
(09)
(09)
(09)
(09)
Medium
Medium
Flat top
MM
(09)
Standard
(09)
LH
(09)
(09)
Dimensions (mm)
Insert Number
R L
SSSCR/L1212F09
Light
LP
Medium
MP

Order Number
Finish
FM
EXTERNAL TURNING
45
LH
45
Finish
FP
WF
External turning,
Facing, Chamfering
LF
HF
WF
Clamp Screw
Wrench
09T3pp
12
12
80 15.2 12
13
TS43
TKY15F
09T3pp
16
16 100 15.2 16
17
TS43
TKY15F
Clamp Torque (N m) : TS43=3.5
C026

SSSC type inserts

A138, A139
A070
TC TOOL HOLDERS
ooINSERTS
LF
a a
STGCR/L1212F13
a a
STGCR/L1616H16
a a
TCGT
TCMW
TCMT
(11,16)
(11,16)
(11,16)
(11,16)
Medium
Flat top
PCD/CBN
(11,16)
(11,13)
MM
(11,16)
1102pp
10
1303pp
16T3pp
LF
LH
(11,16)
Dimensions (mm)
Insert Number
R L
STGCR/L1010E11
Light
LM
HF
Stock
Light
LP
Medium
MP
Order Number
Finish
FM
WF
91
LH
91
Finish
FP
HF
WF
Clamp Screw
Wrench
10
70 13.5 10
12
TS25
TKY08F
12
12
80 17.6 12
16
TS3
TKY08F
16
16
100 20.7 16
20
TS43
TKY15F
EXTERNAL TURNING
STGC
SP type
External turning

STGC type inserts
CBN & PCD inserts
A141 A143
B045, B061
SPARE PARTS
TECHNICAL DATA
A070
P001
Q001
C027
VC TOOL HOLDERS
ooINSERTS
SVJC
SP type
WF
(11,16)
(11,16)
(11,16)
Medium
Medium
Flat top
a a
SVJCR/L1616H16
a a
SVJCR/L2020K16
a a
SVJCR/L2525M16
a a
VCMT
VCMW
MM
Standard
(16)
(16)
(11,16)
LF
1103pp
10
10
70 17
10
1604pp
16
16 100 25
1604pp
20
1604pp
25
(11,16)
Dimensions (mm)
Insert Number
R L
SVJCR/L1010E11
Light
LM
(11,16)
MP
LF
HF
Stock
Light
LP
Medium
Order Number
Finish
FM
EXTERNAL TURNING
93
LH
93
Finish
FP
External turning,
Copying
LH HF WF
Shim
Shim Pin
Clamp Screw
Wrench
12
TS25
zTKY08F
16
20
TS43
zTKY15F
20 125 40
20
25
SPSVN32
BCP141
TS44
xTKY15R
25 150 40
25
32
SPSVN32
BCP141
TS44
xTKY15R
* Clamp Torque (N m) : TS25=1.0, TS43=3.5, TS44=3.5
SVVC
SP type
Finish
FP
7230
LF
Stock
SVVCN1616H16
SVVCN2020K16
(16)
(16)
(16)
Medium
Medium
Flat top
MM
SVVCN2525M16
Standard
(16)
(16)
(16)
Dimensions (mm)
Insert Number
VCMT
VCMW
Light
LM
(16)
(16)
Order Number
Light
LP
Medium
MP
HF
72
30
Finish
FM
WF
External turning,
Copying
LF
HF
WF
Shim
Shim Pin
Clamp Screw
Wrench
1604pp
16
16
100
16
TS43
zTKY15F
1604pp
20
20
125
20 10
SPSVN32
BCP141
TS44
xTKY15R
1604pp
25
25
150
25 12.5
SPSVN32
BCP141
TS44
xTKY15R
C028
SVJC type inserts

SVVC type inserts
A151, A152
A151, A152
CBN & PCD inserts

B049, B064
A070
LF
(16)
(16)
(16)
Medium
Medium
Flat top
a a
SVPCR/L2525M16
a a
Standard
R L
SVPCR/L2020K16
MM
(16)
(16)
(16)
LF
1604pp
20
20 125 30
20
1604pp
25
25 150 30
25
(16)
Dimensions (mm)
Insert Number
VCGT
VCMT
VCMW
Light
LM
(16)
MP
HF
Stock
Light
LP
Medium
Order Number
Finish
FM
WF
11730
LH
117
30
Finish
FP
LH HF WF
Shim
Shim Pin
Clamp Screw
Wrench
25
SPSVN32
BCP141
TS44
TKY15R
32
SPSVN32
BCP141
TS44
TKY15R
EXTERNAL TURNING
SVPC
SP type
Facing, Copying
SVPC type inserts

CBN inserts
A151, A152
B049
A070
SPARE PARTS
TECHNICAL DATA
P001
Q001
C029
XC TOOL HOLDERS
ooINSERTS
SXZC
External turning,
Copying
Profile Holder
Finish
SVX
WF
< 300
HF
EXTERNAL TURNING
LF
92
30
(15)
9230
LH

Stock
Order Number
Dimensions (mm)
Insert Number
R L
SXZCR/L1616H15
a a
SXZCR/L2020K15
a a
SXZCR/L2525M15
a a
Clamp Clamp Bridge Spring Insert Wrench for

B LF LH HF WF Clamp
Screw Bridge
Screw
Wrench clamp bridge
1503pp-SVX 16 16 100 35 16 20 TS255 AMS3 AJS3010T10 ASS2 TKY08F TKY10F

XCMT
1503pp-SVX 20 20 125 35 20 25 TS255 AMS3 AJS3010T10 ASS2 TKY08F TKY10F

1503pp-SVX 25 25 150 40 25 32 TS255 AMS3 AJS3010T10 ASS2 TKF08F TKF10F
Clamp Torque (N m) : TS255=1.0, AJS3010T10=2.5
Depth of Cut (mm)
y Applicable range
Corner R0.8
Corner R0.4
Feed (mm/rev)

Work Material
Mild Steel
Hardness
Grade
Cutting Speed
(m/min)
< 180HB
UE6020
150 350
UE6020
100 250
Carbon Steel, Alloy Steel 150HB 250HB
(Note) The above cutting conditions are general guidelines.

Adjustments maybe necessary depending on machine rigidity, workpiece geometry and clamping.
a
C030

SXZC type inserts
A158
NOTE
Pay special attention to the following when face copying.

Depth from end face
Up to 10mm
Inclination angle
60 or less
Not possible
Machining of V-pulleys
EXTERNAL TURNING
Notes when end face copying

aMachining of an outer diameter (Step z)
To prevent burr formation, the depth of cut should be
below half the nose radius.
Cutting Diameter > & 40mm
aMachining of an inclination (Step x)

2
To reduce the contact length of chips, the depth of

cut should be below half the nose radius.
To prevent interference between the tool and the
workpiece, the cutting diameter should be 40mm or
larger, inclination angle 60 or less and depth from
the end face up to 10mm.
aWhen changing inserts

When indexing the inserts, it is recommended to preset
the cutting edge position to maintain machining accuracy.
When machining V-pulleys,

use a VNMG insert.
SPARE PARTS
TECHNICAL DATA
P001
Q001
C031
EXTERNAL TURNING TOOLS [FOR ALUMINIUM]
DE TOOL HOLDERS
ooINSERTS
SDJE
AL type
WF
Order Number
(15)
R L
SDJER/L1616H15
a a
SDJER/L2020K15
a a
SDJER/L2525M15
a a
DEGX
Right hand tool

holder shown.
LF
(15)
Dimensions (mm)
Insert Number
(15)
R/L-F
LF
Stock
Medium
R/L
PCD
93
LH
HF
EXTERNAL TURNING
93
Finish
R/L-F
External turning,
Copying
LH
HF
WF
Clamp Screw
Wrench
1504pp
16
16 100 27
16
20
CS451190T
TKY20F
1504pp
20
20 125 35
20
25
CS451190T
TKY20F
1504pp
25
25 150 35
25
32
CS451190T
TKY20F
Clamp Torque (N m) : CS451190T=5.0
SDNE
AL type
Finish
R/L-F
Medium
R/L
WF
External turning,
Copying
(15)
6230
62
30
(15)
PCD
R/L-F
LF
HF
10
(15)
Order Number
Stock
SDNEN1616H15
SDNEN2020K15
SDNEN2525M15
DEGX
Dimensions (mm)
Insert Number
H
LF
HF
WF
Clamp Screw
Wrench
1504pp
16
16
100
16
CS451190T
TKY20F
1504pp
20
20
125
20
10
CS451190T
TKY20F
1504pp
25
25
150
25
12.5
CS451190T
TKY20F
Clamp Torque (N m) : CS451190T=5.0

Work Material
Aluminium Alloy
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
HTi10
400
0.05 0.3
0.2 3.0
800
0.05 0.3
0.2 0.5
MD220
SDJE type inserts
a
C032
SDNE type inserts

PCD inserts
A136
A136
B066
TE TOOL HOLDERS
ooINSERTS
Medium
PCD
R/L
WF
R/L
(16)
7
7
Order Number
Stock
STGER/L1616H16
a a
STGER/L2020K16
a a
STGER/L2525M16
a a
TEGX
Right hand tool

holder shown.
LF
(16)
Dimensions (mm)
Insert Number
R L
LH
HF
WF
Clamp Screw
Wrench
1603pp
16
16 100 22
16
20
FC400890T
TKY10F
1603pp
20
20 125 22
20
25
FC400890T
TKY10F
1603pp
25
25 150 22
25
32
FC400890T
TKY10F
Clamp Torque (N m) : FC400890T=2.5
STFE
AL type
91
Medium
R/L
PCD
R/L
Facing
WF
LF
HF
91
(16)
PCD
91
LH
EXTERNAL TURNING
STGE
AL type
External turning
91
(16)
LH
(16)
PCD
LF
Order Number
Stock
STFER/L1616H16
a a
STFER/L2020K16
a a
STFER/L2525M16
a a
TEGX
LF
(16)
Dimensions (mm)
Insert Number
R L
Right hand tool

holder shown.
HF
LH
HF
WF
Clamp Screw
Wrench
1603pp
16
16 100 22
16
20
FC400890T
TKY10F
1603pp
20
20 125 22
20
25
FC400890T
TKY10F
1603pp
25
25 150 22
25
32
FC400890T
TKY10F
hand holder.

Work Material
Aluminium Alloy
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
HTi10
400
0.05 0.3
0.2 3.0
800
0.05 0.3
0.2 0.5
MD220
STGE type inserts

STFE type inserts
PCD inserts
A144
A144
B066
SPARE PARTS
TECHNICAL DATA
P001
Q001
C033
EXTERNAL TURNING TOOLS [FOR ALUMINIUM]
VDTOOL HOLDERS
ooINSERTS
SVJD
AL type
External turning,
Copying
Finish
R/L
EXTERNAL TURNING
WF
LF
93
93
R/L-F
LH
Stock
SVJDR/L1616H16
a a
SVJDR/L2020K16
a a
SVJDR/L2525M16
a a
VDGX
LF
(16)
Dimensions (mm)
Insert Number
R L
HF
Order Number
(16)
PCD
LH
HF
WF
Clamp Screw
Wrench
1603pp
16
16 100 30
16
20
FC400890T
TKY10F
1603pp
20
20 125 30
20
25
FC400890T
TKY10F
1603pp
25
25 150 30
25
32
FC400890T
TKY10F

Work Material
Aluminium Alloy
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
HTi10
400
0.05 0.3
0.2 3.0
800
0.05 0.3
0.2 0.5
MD220
a
C034
SVJD type inserts

PCD inserts
A153
B067
TL HOLDER
HOLDER
Conventional
order number
TLHRLH
IC
(External turning, Copying)
TLHR2020K5
TLHR2020K6
TLHR2525M7
TLHR3225P10
TLHR2020K5
TLHR2020K6
TLHR2525M7
TLHR54P10
HF
LF
Dimensions (mm)
B
HF
LF
Insert
Number
IC
RTG05A
RTG06A
5
6
20
20
RTG07A
25
25
25
150
20
RTG10A
10
32
25
32
170
25
Stock
a
20
20
20
20
125
125
LH
16
16
EXTERNAL TURNING
Revised
order number
Geometry
INSERTS (CBN)
INSERTS
IC
15
Tangent
angle
IC
L17
L17
D4
D4
12
12
Stock
Carbide
UTi20T
HTi10
Order Number
RTG05A
RTG06A
RTG07A
RTG08A
RTG10A
a
a
Dimensions (mm)
IC
5
6
D4
L17
7.5
7.5
2.5
3.5
3.5
3.5
11
3.5
8
10
11
14
4.5
5.5
5
6.5
Order Number
Stock
CBN
MB825
RTG05A
RTG06A
RTG07A
RTG08A
RTG10A
Dimensions (mm)
IC
D4
L17
5
6
7.5
7.5
2.5
3.5
3.5
3.5
11
3.5
8
10
11
14
4.5
5.5
5
6.5
INSERT SEAT LOCATION

When manufacturing a special tool holder, please machine insert seat in accordance to the drawing.
Insert Diameter IC
Insert Seat Dimensions
IC
d1
0.3
0
-0.3
12 -10'
C0.5
d2
l1
l2
Dimensions (mm)
d1
d2
l1
l2
Taper Diameter
5
6
4
4
2.5
3.5
1.9
2.9
1.85
2.35
3.2
3.7
1.5
2.5
3.5
2.5
2.75
4.3
2.1
4.5
3.5
3.25
4.8
3.1
7.5
7.5
5.5
7.5
4.2
6.2
4.15
5.15
5.9
6.9
3.8
5.8
10
12
SPARE PARTS
TECHNICAL DATA
P001
Q001
C035

OF SMALL TOOLS
zOrganized according to the cutting mode of small tools.
(Refer to the inside title on the next page.)
xShown as Turning External Grooving External Cutting Off Threading Boring.

uses illustrations and arrows to depict the
available machining applications such as
external turning, copying, facing, chamfering,
threading, and grooving together with cutting
edge lead angles.
TYPE OF TOOL HOLDER

GEOMETRY
APPLICATION
CHIP BREAKER BY
CUTTING APPLICATION
PRODUCT SECTION
SMALL TOOLS
Finish
Without off set
SMG
Finish
Light
R/L-F
(06)
(06)
(06,09)
(06,09)
Flat top
For nonferrous
metals
CBN/PCD
SMALL TOOLS
Order Number
Right hand tool

holder shown.
Stock
a a
SCACR/L1010K06-SM
a a
SCACR/L1010K09-SM
a a
SCACR/L1212M09-SM
a a
SCACR/L1616M09-SM
a a
CCET
CCGT
CCGW
CCMT
CCMW
NP-CCGW
(06,09)
(06,09)
(06,09)
LF
LH HBKW HF
S4
Clamp Screw
Wrench
125
11
1.6
TS254
TKY08R
SDJCR/L0808K07-SM
a a
10
10
125
10
TS254
TKY08R
SDJCR/L1010K07-SM
a a
09T3pp
10
10
125
16
3.5
10
TS43
TKY15R
SDJCR/L1010K11-SM
a a
09T3pp
12
12
150
14
1.5
12
TS43
TKY15R
SDJCR/L1212M11-SM
a a
09T3pp
16
16
150
16
TS43
TKY15R
SDJCR/L1616M11-SM
a a
a a
a a
SCLCR/L1010K09-SM
a a
SCLCR/L1212M09-SM
a a
SCLCR/L1616M09-SM
a a
Light
R L
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
R-SN
(07, 11)
(07, 11)
(07, 11)
(07, 11)
Medium
Flat top
For nonferrous
metals
CBN/PCD
AZ
(07, 11)
(07, 11)
(07, 11)
Dimensions (mm)
Insert Number
Medium
R-SS
(07, 11)
LF
LH HBKW HF
S4
Clamp Screw
Wrench
0702pp
125
15
TS254
TKY08R
0702pp
10
10
125
10
TS254
TKY08R
11T3pp
10
10
125
24
10
TS43
TKY15R
11T3pp
12
12
150
22
12
TS43
TKY15R
11T3pp
16
16
150
16
TS43
TKY15R

Finish
Without off set
SMG
Finish
Light
R/L-F
CCET
CCGT
CCGW
CCMT
CCMW
NP-CCGW
Medium
R/L-SS
R/L-SN
(06)
(06)
(06,09)
(06,09)
Medium
Flat top
For nonferrous
metals
CBN/PCD
SDNC-SM
AZ
(06,09)
(06,09)
SMG
(06,09)
Right hand tool

holder shown.
(06,09)
*
Order Number
Stock
LF
LH HBKW HF
S4
Clamp Screw
Wrench
125
11
2.1
TS254
TKY08R
SDNCR/L0808K07-SM
a a
0602pp
10
10
125
10
TS254
TKY08R
SDNCR/L1010K07-SM
a a
09T3pp
10
10
125
20
10
TS43
TKY15R
SDNCR/L1010K11-SM
a a
09T3pp
12
12
150
18
12
TS43
TKY15R
SDNCR/L1212M11-SM
a a
09T3pp
16
16
150
16
TS43
TKY15R
SDNCR/L1616M11-SM
a a
Finish
Light
R-F
R L
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
R-SN
(07, 11)
(07, 11)
(07, 11)
(07, 11)
Medium
Flat top
For nonferrous
metals
CBN/PCD
AZ
(07, 11)
(07, 11)
(07, 11)
Dimensions (mm)
Insert Number
Medium
R-SS
R-SR
0602pp
Finish
Neutral edge with handed holder

Without off set
62
30
Dimensions (mm)
Insert Number
R L
SCLCR/L0808K06-SM
Stock
0602pp
Right hand tool

holder shown.
SCLCR/L1010K06-SM
Right hand tool

holder shown.
Order Number
Finish
R-F
R-SR
0602pp
95
Order Number
SMG
(06,09)
R/L-SR
Stock
Finish
Without off set
93
SCLC-SM
SDJC-SM
AZ
Dimensions (mm)
Insert Number
R L
SCACR/L0808K06-SM
R/L-SN
Medium
R/L-SR
90
Medium
R/L-SS
SMALL TOOLS
EXTERNAL FRONT TURNING
SCAC-SM
(07, 11)
LF
LH HBKW HF
S4
Clamp Screw
Wrench
0702pp
125
TS254
TKY08R
0702pp
10
10
125
10
TS254
TKY08R
11T3pp
10
10
125
24
10
TS43
TKY15R
11T3pp
12
12
150
12
TS43
TKY15R
11T3pp
16
16
150
16
TS43
TKY15R

Work Material
Hardness
Grade
Feed (mm/rev)
P Carbon Steel Alloy Steel
180HB280HB
VP15TF
100 (50150)
0.08 (0.010.15)
VP15TF
110 (30180)
0.08 (0.010.15)
NX2525
Free Cutting Steel
150 (50250)
0.08 (0.010.15)
Stainless Steel
< 200HB
VP15TF
80 (50120)
0.06 (0.020.1)
Non-Ferrous Metal
HTi10
150 (70230)
0.09 (0.030.15)
A126 A130
A126 A130
B039 B041, B059
SCAC-SM type inserts

a
D008
SCLC-SM type inserts

CBN & PCD inserts
REFERENCE PAGE FOR

LEGEND FOR STOCK
APPLICABLE INSERTS
STATUS MARK
is shown on the left hand page indicates reference pages
of each double-page spread.
giving details of inserts that

are applicable to the product.
PRODUCT STANDARDS
and spare parts.

D000
SDJC-SM type inserts

SDNC-SM type inserts
CBN & PCD inserts
A132 A135
A132 A135
B043, B044, B060
SPARE PARTS
TECHNICAL DATA
PAGE REFERENCE
SPARE PARTS
TECHNICAL DATA
indicates reference pages,
including the above, on the
right hand page of each
double-page spread.

for each work material classification,
indicates recommended cutting conditions
according to the ISO categories
for cutting grades, P, M and N.
P001
Q001
D009
TURNING TOOLS
SMALL TOOLS
OUTLINE OF SMALL TOOLS ....... D002
CLASSIFICATION.......................... D004
*Arranged by Alphabetical order

D012 BTAH
D012
D013
D014
D014
D027
D028
D028
D028
D027
D027
D029
D029
D018
D018
D019
D013
D020
D020
D021
D021
D022
D022
D023
D023
D016
D016
D016
D016
D016
D016
D030
D030
D008
D008
D009
D009
D026
D010
D010
D011
D011
D024
D024
BTAT INSERTS
BTBT INSERTS
BTVH
BTVT INSERTS
CSVH
CSVTBXL INSERTS
CSVTB INSERTS
CSVTC INSERTS
CSVTF INSERTS
CSVTFXL INSERTS
CSVTG INSERTS
CSVTT INSERTS
CTAH
CTAH-S
CTAT INSERTS
CTBH
CTBH
CTBT INSERTS
CTCH
CTCT INSERTS
CTDH
CTDT INSERTS
CTEH
CTET INSERTS
GTAH
GTAT INSERTS
GTBH
GTBT INSERTS
GTCH
GTCT INSERTS
SBAH
SBAT INSERTS
SCAC-SM
SCLC-SM
SDJC-SM
SDNC-SM
SH
SVJB-SM
SVLP-SM
SVPP-SM
SVVB-SM
TTAH
TTAT INSERTS
STANDARD FOR GANG TYPE TOOL POSTS

SCAC-SM ................................ D008
SCLC-SM................................. D008
SDJC-SM ................................. D009
SDNC-SM ................................ D009
SVLP-SM ................................. D010
SVJB-SM ................................. D010
SVVB-SM................................. D011
SVPP-SM ................................. D011
EXTERNAL BACK TURNING
BTAH ....................................... D012
CTBH ....................................... D013
BTVH ....................................... D014
EXTERNAL GROOVING
GTAH ....................................... D016
GTBH ....................................... D016
GTCH ....................................... D016
EXTERNAL CUTTING OFF
CTAH ....................................... D018
CTAH-S.................................... D018
CTBH ....................................... D020
CTCH ....................................... D021
CTDH ....................................... D022
CTEH ....................................... D023
EXTERNAL THREADING
TTAH ....................................... D024
EXTERNAL FRONT TURNING, COPYING, FACING
SH ............................................ D026
CAM TYPE TOOL POSTS
CSVH ....................................... D027
BORING
SBAH ....................................... D030
D001
SMALL TOOLS
OUTLINE OF SMALL TOOLS
SMALL TOOLS
TOOLS FOR GANG TYPE AUTOMATIC LATHES (FOR EXTERNAL TURNING AND BORING)
Back Turning
Grooving
Front Turning
Nose radii designed with

minus tolerance
SMG Breaker Insert

0
RE -0.05
mm
Suitable for small parts applications that often

require minus tolerance dimensions.
a The order number is shown with the letter M
that indicates minus tolerance.
a The radius value is printed on the side of
the insert label for easy recognition.
a
0 20
Cut Off
Diameter
< & 35
a Back Clamping
Mechanism
Sharp cutting edge
a Back Turning
Insert Thickness
3.5mm
a Grooving
3-cornered
Groove width 0.3 3.0mm
a Traversing possible
D002
a Front Turning
ISO E class accuracy inserts

A wide variety of small corner R inserts
a Rake angle 30
20
Screw designed for front

and back clamping.
Can machine to the

end face
a Threading
Over Hang 7.5mm
Cutting Edge Width

0.7 3.0mm
RE
E class
0
RE -0.02
mm
Conventional G-class insert

RE e0.10 mm
Effective Cutting Edge Length 6.0mm
a Cutting Off
Boring
a Tolerance Corner R
A combination of a
curved cutting edge
and the protrusion type
breaker promotes
efficient chip breaking.
a SMG Breaker Insert
Threading
Step Difference 6.5mm
Cutting Off
Tools for a very wide range of

small parts machining
External Turning
Internal Turning
Tools for front turning, back turning,

grooving, threading, and cutting off
Tools for boring, internal grooving and
internal threading
a The most suitable for the use with cam type automatic
lathes (radial pattern tool posts)
a The most suitable for machining of small parts with work
diameter 5mm or smaller
a Single holder for front turning, back turning, grooving,
threading and cutting off operations
Drills
End Milling
SMALL TOOLS
Drilling
TOOLS FOR CAM TYPE AUTOMATIC LATHES
End Mills
Tools for CNC automatic and small lathes

Types of Tool Posts
Tool Sizes
Gang type, turret type, cam type (radial

pattern type)
Square shank: 816 mm
Round shank : less than &25.4
Indexable inserts developed under the concept of

"high quality, high efficiency and long tool life."
High Quality
E class tolerance, sharp cutting edge, high

accuracy small corner R, smooth surface finish
Long Tool Life
Miracle Coating (VP15TF), cermet

(NX2525), cemented carbide (HTi10)
High Efficiency
Regrinding not necessary due to the

employment of indexable inserts. A wide
variety of top cutting edge geometries
INTERNAL TURNING TOOLS

Solid type
Back Turning
Grooving
Threading
Cutting Off
DRILLING TOOLS
MICRO-MINI TWIN
Boring Bars
Minimum cutting
diameter &2.2
Boring
Grooving
Threading
Front Turning
aCarbide drills
aHSS drills

&12.0
Round Shank
TAF Drill
END MILLING TOOLS
Square Shank
aCarbide end mills

aHSS end mills
MICRO-DEX Boring Bars

&5.0

&10.0
DIMPLE BAR
D003
SMALL TOOLS
CLASSIFICATION OF EXTERNAL TURNING TOOLS

GANG TYPE TOOL POSTS
a FRONT TURNING
Name of
Tool Holder
SMALL TOOLS
SCAC-SM
a THREADING
Shank Size (mm)

(H x W x L)
8
10
12
16
x 8 x 125
x 10 x 125
x 12 x 150
x 16 x 150
8
10
12
16
x 8 x 125
x 10 x 125
x 12 x 150
x 16 x 150
Geometry
90
8
10
12
16
x 8 x 125
x 10 x 125
x 12 x 150
x 16 x 150
95
8
10
12
16
x 8 x 125
x 10 x 125
x 12 x 150
x 16 x 150
^ D009
SVLP-SM
GTAH
(Groove Width
0.3 3.0mm)
93
^ D016
GTBH
(Groove Width
1.45 3.0mm)
62
30
GTCH
10 x 10 x 125
12 x 12 x 150
16 x 16 x 150
(Groove Width
2.5 3.0mm)
95
10 x 10 x 125
12 x 12 x 150
16 x 16 x 150
SVVB-SM
Name of
Tool Holder
CTAH
(Max. Cut Off

Diameter
12mm)
10 x 10 x 125
12 x 12 x 150
16 x 16 x 150
117
30
CTAH-S
72
30
(Max. Cut Off

Diameter
16mm)
BTAH
(Insert Size
2.8, 3.5, 5.0mm)
Shank Size (mm)

(H x W x L)
x
x
x
x
10
10
12
16
x
x
x
x
Geometry
CTBH
(Max. Cut Off

Diameter
20mm)
(Insert Size
7.5mm)
^ D014
D004
x
x
x
x
x
x
x
80
120
80
120
80
120
120
10
10
12
16
x
x
x
x
10
10
12
16
x 80
x 120
x 120
x 120
Geometry
U Type
E Type
VT Type
U Type
E Type
VT Type
U Type
E Type
VT Type
10 x 10 x 80
10 x 10 x 120
Shank Size (mm)

(H x W x L)
8
10
12
16
x
x
x
x
10
10
12
16
x
x
x
x
120
120
120
120
10 x 10 x
80
10 x 10 x 120
12 x 12 x 120
16 x 16 x 120
10 x 10 x 120
12 x 12 x 120
^ D021
CTDH
10 x 10 x 120
12 x 12 x 120
16 x 16 x 120
(Max. Cut Off

Diameter
2335mm)
16 x 16 x 120
16 x 16 x 125
^ D022
^ D013
BTVH
8
8
10
10
12
12
16
^ D020
CTCH
120
120
120
120
^ D012
(Insert Size
4.5, 6.0mm)
x
x
x
x
x
x
x
^ D018
CTBH
8
10
12
16
8
8
10
10
12
12
16
(Max. Cut Off

Diameter
12mm)
a BACK TURNING
Name of
Tool Holder
Shank Size (mm)

(H x W x L)
^ D018
10 x 10 x 125
12 x 12 x 150
16 x 16 x 150
^ D011
120
120
120
120
a CUTTING OFF
^ D010
^ D011
x
x
x
x
^ D016
93
SVPP-SM
10
10
12
16
^ D016
^ D010
SVJB-SM
x
x
x
x
^ D024
Name of
Tool Holder
^ D009
SDNC-SM
8
10
12
16
Geometry
a GROOVING
^ D008
SDJC-SM
Shank Size (mm)

(H x W x L)
TTAH
^ D008
SCLC-SM
Name of
Tool Holder
CTEH
10 x 10 x 120
12 x 12 x 120
16 x 16 x 120
53
(Max. Cut Off

Diameter
2335mm)
^ D023
16 x 16 x 120
16 x 16 x 125
Geometry
OPPOSITE TOOL POSTS

Name of
Tool Holder
SH
(Front Turning,
Copying, Facing)
^ D026
a THREADING
Shank Size (mm)

(Shank Dia. x L)
&15.875
&19.05
&20
&22
&25.4
x
x
x
x
x
100
125
125
125
150
Geometry
Name of
Tool Holder
Shank Size (mm)

(H x W x L)
MMT
93
12
16
20
25
32
^ G012
SMGH
x
x
x
x
x
12
16
20
25
32
x
x
x
x
x
Geometry
100
100
125
150
170
SMALL TOOLS
a DIMPLE SLEEVE HOLDER
10 x 10 x 70
12 x 12 x 80
16 x 16 x 100
^ G024
TURRET TYPE TOOL POSTS

a FRONT TURNING
Name of
Tool Holder
DTGN
Name of
Tool Holder
Shank Size (mm)

(H x W x L)
Geometry
16 x 16 x 100
20 x 20 x 125
25 x 25 x 150
91
^ C016
MTJN
^ C016
SCLC
10
12
16
20
25
8
10
12
16
x
x
x
x
x
10
12
16
20
25
x 70
x 80
x 100
x 125
x 150
x 8 x 60
x 10 x 70
x 12 x 80
x 16 x 100
8
10
12
16
x 8 x 60
x 10 x 70
x 12 x 80
x 16 x 100
^ C028
CSVH
(Front Turning
Copying)
^ D027
CSVH
(Back Turning)
62
30
^ D027
CSVH
(Back Turning
Copying)
^ D027
CSVH
(Cutting Off)
10 x 10 x 70
12 x 12 x 80
16 x 16 x 100
^ D027
91
CSVH
(Grooving)
10 x 10 x 70
16 x 16 x 100
^ D027
93
^ C028
SVVC
^ D027
95
45
^ C027
SVJC
CSVH
(Front Turning)
12 x 12 x 80
16 x 16 x 100
^ C026
STGC
91
93
^ C023
SSSC
10 x 10 x 70
12 x 12 x 80
16 x 16 x 100
^ F124
Name of
Tool Holder
10 x 10 x 70
12 x 12 x 80
16 x 16 x 100
^ C023
SDNC
Geometry
CAM TYPE TOOL POSTS
93
^ C022
SDJC
SMGH
Shank Size (mm)

(H x W x L)
20 x 20 x 125
25 x 25 x 150
^ C017
PTGN
a GROOVING
CSVH
(Threading)
16 x 16 x 100
72
30
^ D027
Shank Size (mm)

(H x W x L)
7 x 7 x
8 x 8 x
9.5 x 9.5 x
10 x10 x
12 x12 x
140
140
140
140
140
7 x 7 x
8 x 8 x
9.5 x 9.5 x
10 x10 x
12 x12 x
140
140
140
140
140
7 x 7 x
8 x 8 x
9.5 x 9.5 x
10 x10 x
12 x12 x
140
140
140
140
140
7 x 7 x
8 x 8 x
9.5 x 9.5 x
10 x10 x
12 x12 x
140
140
140
140
140
7 x 7 x
8 x 8 x
9.5 x 9.5 x
10 x10 x
12 x12 x
140
140
140
140
140
7 x 7 x
8 x 8 x
9.5 x 9.5 x
10 x10 x
12 x12 x
140
140
140
140
140
7 x 7 x
8 x 8 x
9.5 x 9.5 x
10 x10 x
12 x12 x
140
140
140
140
140
Geometry
D005
SMALL TOOLS
FOR
(
CLASSIFICATION OF INTERNAL TURNING TOOLS GENERAL USE)
Product Name
Holder
SBAH
SMALL TOOLS
Steel Shank
Carbide Shank
Min. Cutting Diameter : 3mm
^ D030
MICRO-MINI CB
CR
TWIN
Boring Bars
Steel Shank
Carbide Shank
Min. Cutting Diameter : 2.2mm
^ E019
CooFR-BLS
^ E022
FSVUB/C
(Steel Shank)
FSVPB/C
DIMPLE BAR
(Steel Shank)
^ E017
^ E011
SWUB
FSVJC
DIMPLE BAR
(Steel Shank)
(Carbide Shank)
^ E016
FSWL1
^ E012
FSWUB/P
DIMPLE BAR FSWUB/P-E
F type Bars
Steel Shank
Carbide Shank
(Steel Shank)
^ E027
FSWL2
F type Bars
(Carbide Shank)
FSCLC/P
DIMPLE BAR FSCLC/P-E
Steel Shank
Carbide Shank
D006
^ E011
STUC
(Carbide Shank)
^ E006
^ E007
DIMPLE BAR
^ E016
^ E027
FSTUP
DIMPLE BAR FSTUP-E
SCLC
(Carbide Shank)
MICRO-DEX
Boring Bars
^ E009
Steel Shank
Carbide Shank
(Solid Carbide)
MICRO-DEX
Boring Bars
^ E008
FSDQC
DIMPLE BAR FSDQC-E
(Solid Carbide)
MICRO-DEX
Boring Bars
Holder
FSDUC
DIMPLE BAR FSDUC-E
For Gang Type

Tool Posts
MICRO-MINI
Boring Bars
Product Name
^ E010
GROOVING/THREADING
(
CLASSIFICATION OF INTERNAL TURNING TOOLS END MILLING/DRILLING )
FOR GROOVING AND THREADING
Product Name
Holder
(Solid Type)
^ F126
MICRO-MINI CT TYPE(Threading)
TWIN
Boring Bars
SMALL TOOLS
MICRO-MINI CG TYPE(Grooving)
TWIN
Boring Bars
(Solid Type)
^ G026
F type Bars
FSL51
FSL52
Steel Shank
Carbide Shank
(Grooving)
(Threading)
^ F130
END MILLS
Solid Carbide End Mill series
^ J024
HSS End Mill series
^ J043
DRILLS
MVX/TAF Drill (Indexable type)
^ N212
Solid Carbide Drill series
^ N004
Solid Gun Drill series
^ N124
HSS Drill series
^ N010
D007
SMALL TOOLS
SCAC-SM
Finish
Without off set
S4
SMALL TOOLS
SCACR/L1010K06-SM
a a
SCACR/L1010K09-SM
a a
SCACR/L1212M09-SM
a a
SCACR/L1616M09-SM
a a
(06,09)
CBN/PCD
CCET
CCGT
CCGW
CCMT
CCMW
NP-CCGW
AZ
(06,09)
(06,09)
(06,09)
Dimensions (mm)
H
LF
LH HBKW HF
0602pp
125
11
1.6
0602pp
10
10
125
09T3pp
10
10
125
09T3pp
12
12
09T3pp
16
16
(06,09)
S4
Clamp Screw
Wrench
TS254
TKY08R
10
TS254
TKY08R
16
3.5
10
TS43
TKY15R
150
14
1.5
12
TS43
TKY15R
150
16
TS43
TKY15R
SCLC-SM
Finish
Without off set
SMG
95
Order Number
SCLCR/L0808K06-SM
SCLCR/L1010K06-SM
a a
SCLCR/L1010K09-SM
a a
SCLCR/L1212M09-SM
a a
SCLCR/L1616M09-SM
a a
(06)
(06,09)
(06,09)
Flat top
For nonferrous
metals
CBN/PCD
Right hand tool

holder shown.
CCET
CCGT
CCGW
CCMT
CCMW
NP-CCGW
AZ
(06,09)
(06,09)
(06,09)
Dimensions (mm)
Insert Number
R L
a a
Medium
R/L-SN
(06)
R/L-SR
LF
HF
Stock
Light
R/L-SS
Medium
S4
LH
95
Finish
R/L-F
HBKW
a a
(06,09)
For nonferrous
metals
Right hand tool

holder shown.
Insert Number
R L
SCACR/L0808K06-SM
(06)
Flat top
LF
HF
Stock
Medium
R/L-SN
(06)
R/L-SR
90
Order Number
Light
R/L-SS
Medium
LH
90
Finish
R/L-F
HBKW
SMG
LF
LH HBKW HF
0602pp
125
11
2.1
0602pp
10
10
125
09T3pp
10
10
125
20
09T3pp
12
12
150
18
09T3pp
16
16
150
(06,09)
S4
Clamp Screw
Wrench
TS254
TKY08R
10
TS254
TKY08R
10
TS43
TKY15R
12
TS43
TKY15R
16
TS43
TKY15R
SCAC-SM type inserts
a
D008
SCLC-SM type inserts

CBN & PCD inserts
A126 A130
A126 A130
B039 B041, B059
S4
LH
93
a a
SDJCR/L1010K07-SM
a a
SDJCR/L1010K11-SM
a a
SDJCR/L1212M11-SM
a a
SDJCR/L1616M11-SM
a a
Right hand tool

holder shown.
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
(07, 11)
(07, 11)
(07, 11)
(07, 11)
Medium
Flat top
For nonferrous
metals
CBN/PCD
AZ
(07, 11)
(07, 11)
(07, 11)
Dimensions (mm)
Insert Number
R L
SDJCR/L0808K07-SM
Medium
R-SN
LF
H
Stock
Light
R-SS
R-SR
93
HF
Order Number
Finish
R-F
HBKW
SMG
LF
LH HBKW HF
0702pp
125
15
0702pp
10
10
125
11T3pp
10
10
125
11T3pp
12
12
11T3pp
16
16
(07, 11)
S4
Clamp Screw
Wrench
TS254
TKY08R
10
TS254
TKY08R
24
10
TS43
TKY15R
150
22
12
TS43
TKY15R
150
16
TS43
TKY15R
SMALL TOOLS
SDJC-SM
Finish
Without off set
SDNC-SM
S4
62
30
6230'
SDNCR/L1010K07-SM
a a
SDNCR/L1010K11-SM
a a
SDNCR/L1212M11-SM
a a
SDNCR/L1616M11-SM
a a
Right hand tool

holder shown.
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
Light
Medium
R-SS
R-SN
(07, 11)
(07, 11)
(07, 11)
(07, 11)
Medium
Flat top
For nonferrous
metals
CBN/PCD
AZ
(07, 11)
(07, 11)
(07, 11)
Dimensions (mm)
Insert Number
R L
SDNCR/L0808K07-SM
Finish
R-F
R-SR
LF
HF
Stock
a a
SMG
LH
Order Number
Finish

Without off set
HBKW
LF
LH HBKW HF
0702pp
125
0702pp
10
10
125
11T3pp
10
10
125
24
11T3pp
12
12
150
11T3pp
16
16
150
(07, 11)
S4
Clamp Screw
Wrench
TS254
TKY08R
10
TS254
TKY08R
10
TS43
TKY15R
12
TS43
TKY15R
16
TS43
TKY15R

Work Material
Hardness
Grade
Feed (mm/rev)
180HB280HB
VP15TF
100 (50150)
0.08 (0.010.15)
VP15TF
110 (30180)
0.08 (0.010.15)
NX2525
150 (50250)
0.08 (0.010.15)
0.06 (0.020.1)
Free Cutting Steel
Stainless Steel
< 200HB
VP15TF
80 (50120)
Non-Ferrous Metal
HTi10
150 (70230)
SDJC-SM type inserts

SDNC-SM type inserts
CBN & PCD inserts
A132 A135
A132 A135
B043, B044, B060
0.09 (0.030.15)
SPARE PARTS
TECHNICAL DATA
P001
Q001
D009
SMALL TOOLS
SVLP-SM
Finish
Without off set

S4
R/L-SRF
(08,11)
95
Finish
LF
SMG
HF
95
SMALL TOOLS

Order Number
Stock
a a
SVLPR/L1212M08-SM
a a
VPET
VPGT
(08,11)
LF
HF
S4
Clamp Screw
Wrench
0802pp
10
10
125
10
TS202
TKY06R
0802pp
12
12
150
12
TS202
TKY06R
1103pp
10
10
125
10
TS255
TKY08R
SVLPR/L1010K11-SM
a a
SVLPR/L1212M11-SM
a a
1103pp
12
12
150
12
TS255
TKY08R
SVLPR/L1616M11-SM
a a
1103pp
16
16
150
16
TS255
TKY08R
SVJB-SM
Finish
Without off set

S4
93
LF
Stock
SVJBR/L1010K11-SM
SVJBR/L1212M11-SM
a a
SVJBR/L1616M11-SM
a a
VBET
VBGT
VBMT
(11)
Medium
R/L-SR
(11)
Dimensions (mm)
Insert Number
R L
a a
(11)
Medium
MV

Order Number
R/L-SN
HF
93
Medium
R/L-F
SVLPR/L1010K08-SM
Dimensions (mm)
Insert Number
R L
(11)
LF
HF
S4
Clamp Screw
Wrench
1103pp
10
10
125
10
TS255
TKY08R
1103pp
12
12
150
12
TS255
TKY08R
1103pp
16
16
150
16
TS255
TKY08R
* Clamp Torque (N m) : TS255=1.0
SVLP-SM type inserts

a
D010
: Inventory maintained in Japan. (10 inserts in one case)
SVJB-SM type inserts

CBN & PCD inserts
A154
A148 A150
B048, B064
SVVB-SM
Finish
Medium
R/L-SN
R/L-F
(11)
Medium
S4
(11)
Medium
7230'
LF
MV
Stock
Dimensions (mm)
Insert Number
R L
SVVBR/L1010K11-SM
a a
SVVBR/L1212M11-SM
a a
SVVBR/L1616M11-SM
a a
VBET
VBGT
VBMT
(11)
(11)
LF
HF
S4
Clamp Screw
Wrench
1103pp
10
10
125
10
TS255
TKY08R
1103pp
12
12
150
12
TS255
TKY08R
1103pp
16
16
150
16
TS255
TKY08R
SMALL TOOLS

Order Number
R/L-SR
HF
72
30
SVPP-SM
Finish
Finish
11730'
117
30
SMG
LF
Stock
SVPPR/L1010K11-SM
SVPPR/L1212M11-SM
a a
SVPPR/L1616M11-SM
a a
SVPPR/L1616M11-SM
VPET
VPGT
Dimensions (mm)
Insert Number
R L
a a
LH
HF
Order Number
(11)
S4
LH
HBKW
R/L-SRF
(11)
LF
LH
HBKW
HF
S4
Clamp Screw
Wrench
1103pp
10
10
125
20
10
TS255
TKY08R
1103pp
12
12
150
20
12
TS255
TKY08R
1103pp
16
16
150
17
16
TS255
TKY08R

Work Material
Hardness
Grade
Feed (mm/rev)
180HB280HB
VP15TF
100 (70120)
0.06 (0.020.1)
Free Cutting Steel
VP15TF
110 (30180)
0.06 (0.020.1)
Stainless Steel
< 200HB
VP15TF
100 (70120)
0.06 (0.020.1)
SVVB-SM type inserts
SVPP-SM type inserts
CBN & PCD inserts
A148 A150
A154
B048, B064
SPARE PARTS
TECHNICAL DATA
P001
Q001
D011
SMALL TOOLS
BTAH
LF
5.5
S4
HF
H3
KAPR LE
SMALL TOOLS
15
Order Number
Stock
R L
BTAHR/L0810-50
a a
BTAHR/L1010-50
a a
BTAHR/L1212-50
a a
BTAHR/L1616-50
5528ppR/L-B
BTAT
Dimensions (mm)
Insert Number
6035ppR/L-B
605000RX
LF
HF
H3
S4
Clamp Screw
Wrench
10
120
12
3.5
NS402W
NKY15R
10
10
120
10
12
3.5
NS402W
NKY15R
12
12
120
12
3.5
NS403W
NKY15R
16
16
120
16
3.5
NS403W
NKY15R
(Note 1) Please use right hand insert for right hand holder and left hand insert for left hand holder.
(Note 2) Set the maximum depth of cut at under 60% of the effective cutting edge length (LE).
Clamp Torque (N m) : NS402W=1.0, NS403W=1.0
INSERTS
BTAT552800R-B
Coated
Dimensions (mm)
KAPR
RE
LE
BTAT552800L-B
55
2.8
BTAT552801R-B
55
2.8
55
0.1
2.8
BTAT552801L-B
55
0.1
2.8
BTAT603500R-B
60
3.5
BTAT603500L-B
60
3.5
BTAT603501R-B
60
0.1
3.5
BTAT603501L-B
60
0.1
3.5
BTAT605000RX
60
5.0
Geometry
*
With Breaker
RE
20
*12
8
VP15TF
0.5
Hand
2.5
Order Number
50
RE
1.25
Without Breaker
2.5
20
*12
50
* Numeric value set insert on holder.

Work Material
Hardness
Grade
Feed (mm/rev)
180HB280HB
VP15TF
100 (50150)
0.08 (0.010.15)
Free Cutting Steel
VP15TF
110 (30180)
0.08 (0.010.15)
Stainless Steel
< 200HB
VP15TF
80 (50120)
0.06 (0.020.1)
Non-Ferrous Metal
VP15TF
150 (70230)
D012
0.09 (0.030.15)
CTBH
LF
S4
7.5
LE
19.5
Order Number
Stock
R L
CTBHR/L1010-160
a a
CTBHR/L1212-160
a a
CTBHR/L1616-160
a a
BTBT
Dimensions (mm)
Insert Number
60450pR/L-B
606000R/L
LF
HF
H3
S4
Clamp Screw
Wrench
10
10
120
10
12
3.4
NS402W
NKY15R
12
12
120
12
3.4
NS403W
NKY15R
16
16
120
16
3.4
NS403W
NKY15R
SMALL TOOLS
H3
HF
60
INSERTS
0.2
4.5
0.2
4.5
BTBT604501R-B
0.1
0.3
4.5
BTBT604501L-B
0.1
0.3
4.5
BTBT604500L-B
Geometry
With Breaker
RE
25
0.2
6.0
BTBT606000L
0.2
6.0
CF
RE
0.7
3.5
BTBT606000R
5.5
*15
45
Without Breaker
CF
BTBT604500R-B
0.7
LE
(mm)
VP15TF
3.5
Dimensions (mm)
CF
Hand
9.4
Coated
RE
Order Number
25
9.4
*15
45
SPARE PARTS
TECHNICAL DATA
P001
Q001
D013
SMALL TOOLS

LE
8.5
SMALL TOOLS
Order Number
LF
Right hand tool

holder only.
HF
Stock
Dimensions (mm)
Insert Number
LF
HF
S4
BTVHR1010-75
10
10
120
10
BTVHR1212-75
12
12
120
BTVHR1616-75
16
16
BTVHR1010-75F
10
BTVHR1212-75F
BTVHR1616-75F
BTVT
5375ppR-B
Clamp Screw
Wrench
7.5
NS251
NKY15R
12
7.5
NS251
NKY15R
120
16
7.5
NS251
NKY15R
10
120
10
10.0
NS251
NKY15R
12
12
120
12
10.0
NS251
NKY15R
16
16
120
16
10.0
NS251
NKY15R
(Note 2) For high load machining, F type is recommended.
Clamp Torque (N m) : NS251=1.0
INSERTS
Dimensions (mm)
VP15TF
IC
RE
6.35
3.18
0.05
7.5
6.35
3.18
0.1
7.5
Hand
BTVT5375V5R-B
BTVT537501R-B
Geometry
With Breaker
RE
7
IC
(0.5)
Coated
LE
(mm)
Order Number
LE

Work Material
Hardness
Grade
Feed (mm/rev)
180HB280HB
VP15TF
100 (50150)
0.08 (0.010.15)
Free Cutting Steel
VP15TF
110 (30180)
0.08 (0.010.15)
Stainless Steel
< 200HB
VP15TF
80 (50120)
0.06 (0.020.1)
Non-Ferrous Metal
VP15TF
150 (70230)
D014
B=16
BTVHRpppp-75F
53
53
B=12
S4
B=10
BTVH
0.09 (0.030.15)
SPARE PARTS
TECHNICAL DATA
P001
Q001
Memo
D015
SMALL TOOLS
EXTERNAL GROOVING
GTAH, GTBH, GTCH
LF
HF
VT Type
H3
U Type
E Type
Order Number
Stock
Standard Shank
GTAHR/L0808-20S
a a
Insert Number
GTAHR/L1010-20S
a a
GTAHR/L1212-20S
a a
GTBHR/L1010-30S
a a
GTCHR/L1010-30S
a a
GTAT
GTBT 1
GTCT 1
*
*
15
HF
LF
CDX*
H3
(mm) Clamp Screw
Wrench
0.3
3.0
0.3
3.0
NS404W
NKY15R
NS404W
NKY15R
0.3
3.0
1.45
3.0
2.5
3.0
0.3
3.0
0.3
3.0
0.3
3.0
0.3
3.0
1.45
3.0
1.45
3.0
1.45
3.0
2.5
3.0
NS404W
NKY15R
NS404W
NKY15R
NS404W
NKY15R
NS404W
NKY15R
NS404W
NKY15R
NS404W
NKY15R
NS404W
NKY15R
NS404W
NKY15R
NS404W
NKY15R
NS404W
NKY15R
NS404W
NKY15R
pppp
80
13
pppp
10
10
10
80
13
pppp
12
12
12
80
13
GTBT. GTCT
pppp
10
10
10
80
13
GTCT
pppp
10
10
10
80
13
GTAHR/L0808-20
a a
GTAHR/L1010-20
a a
GTAHR/L1212-20
a a
GTAHR/L1616-20
a a
pppp
16
16
16
120
GTBHR/L1010-30
a a
pppp
10
10
10
120
13
GTBHR/L1212-30
a a
pppp
12
12
12
120
13
GTBHR/L1616-30
a a
pppp
16
16
16
120
16
GTCHR/L1010-30
a a
pppp
10
10
10
120
13
GTAT
1
GTBT
1
GTCT
*
*
GTBT. GTCT
GTCT
*2
Cutting
Width
Dimensions (mm)
R L
Long Shank
SMALL TOOLS
CDX
pppp
120
13
pppp
10
10
10
120
13
pppp
12
12
12
120
13
(Note) Please use right hand insert for right hand holder and left hand insert for left hand holder.
1 Even if the insert dimension PDPT exceeds the holder dimension CDX, it is not possible to machine depths over CDX.
2 Clamp Torque (N m) : NS404W=1.0
*
*
INSERTS
Hand
GTAT 03006V3R-U
GTAT 03006V3L-U
GTAT 05012V5R-U
GTAT 05012V5L-U
GTAT 07520V5R-U
GTAT 07520V5L-U
GTAT 09520V5R-U
GTAT 09520V5L-U
GTAT 10020V5R-U
GTAT 10020V5L-U
GTAT 10320V5R-U
GTAT 12520V5R-U
GTAT 12520V5L-U
GTBT14530V5R-U
GTBT14530V5L-U
GTBT15030V5R-U
GTBT15030V5L-U
GTBT17530V5R-U
GTBT17530V5L-U
GTBT20030V5R-U
GTBT20030V5L-U
GTCT25030V5R-U
GTCT25030V5L-U
R
L
R
L
R
L
R
L
R
L
R
R
L
R
L
R
L
R
L
R
L
R
L
D016
Coated
Dimensions (mm)
VP15TF
CW
PDPT *
0.3
0.3
0.5
0.5
0.75
0.75
0.95
0.95
1.0
1.0
1.03
1.25
1.25
1.45
1.45
1.5
1.5
1.75
1.75
2.0
2.0
2.5
2.5
0.6
0.6
1.2
1.2
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
RE
IC
0.03
0.03
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
Geometry
U Type Breaker (General purpose Grooving)
20
IC
+0.05
CW 0
RE
RE
PDPT
Order Number
INSERTS
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
* aa
*a
*a
*
CW
PDPT
RE
IC
0.33
0.33
0.43
0.43
0.53
0.53
0.75
0.75
0.95
0.95
1.0
1.0
1.0
1.0
1.2
1.2
1.2
1.2
1.4
1.4
1.5
1.5
1.5
1.5
1.8
1.8
2.0
2.0
2.0
2.0
2.25
2.25
2.5
2.5
2.75
2.75
3.0
3.0
0.33
0.43
0.53
0.65
0.75
0.8
0.85
0.95
1.0
1.1
1.2
1.3
1.4
1.5
2.0
1.76
1.76
0.6
0.6
1.2
1.2
1.2
1.2
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
0.6
1.2
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
3.0
3.0
3.0
3.0
0
0
0.03
0.03
0.03
0.03
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.1
0.1
0.05
0.05
0.1
0.1
0.05
0.05
0.05
0.05
0.1
0.1
0.05
0.05
0.05
0.05
0.1
0.1
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
Geometry
3.18 E Type Breaker (Ring processing Grooving)

3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
20
CW 0.025
3.18
RE
RE
3.18
3.18
3.18
3.18
3.18
S
IC
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
3.18
0.25 VT Type Breaker
3.18
0.9 (Grooving, Side Turning)
3.18
1.6
3.18
1.6
CW 0.025
3.18
1.6
14
3.18
1.6
RE
RE
3.18
1.6
3.18
1.6
3.18
1.6
3.18
1.6
3.18
1.6
S
IC
3.18
1.6
3.18
1.6
3.18
2.7
3.18
2.7
3.18 Blank
3.18
CW
3.18
3.18
SMALL TOOLS
VP15TF VP15KZ TF15
Dimensions (mm)
PDPT
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
L
R
L
Carbide
PDPT
GTAT 03306V3R-E
GTAT 03306V3L-E
GTAT 04312V3R-E
GTAT 04312V3L-E
GTAT 05312V5R-E
GTAT 05312V5L-E
GTAT 07520V5R-E
GTAT 07520V5L-E
GTAT 09520V5R-E
GTAT 09520V5L-E
GTAT 10020V5R-E
GTAT 10020V5L-E
GTAT 1002001R-E
GTAT 1002001L-E
GTAT 12020V5R-E
GTAT 12020V5L-E
GTAT 1202001R-E
GTAT 1202001L-E
GTAT 14020V5R-E
GTAT 14020V5L-E
GTBT15030V5R-E
GTBT15030V5L-E
GTBT1503001R-E
GTBT1503001L-E
GTBT18030V5R-E
GTBT18030V5L-E
GTBT20030V5R-E
GTBT20030V5L-E
GTBT2003001R-E
GTBT2003001L-E
GTBT22530V5R-E
GTBT22530V5L-E
GTCT25030V5R-E
GTCT25030V5L-E
GTCT27530V5R-E
GTCT27530V5L-E
GTCT30030V5R-E
GTCT30030V5L-E
GTAT 0330600R-VT
GTAT 0431200R-VT
GTAT 0532000R-VT
GTAT 0652000R-VT
GTAT 0752000R-VT
GTAT 0802000R-VT
GTAT 0852000R-VT
GTAT 0952000R-VT
GTAT 1002000R-VT
GTAT 1102000R-VT
GTAT 1202000R-VT
GTAT 1302000R-VT
GTAT 1402000R-VT
GTBT1503000R-VT
GTBT2003000R-VT
GTATR
GTATL
GTBTR
GTBTL
Coated
PDPT
Hand
Max. Cutting Depth (mm)
Order Number
IC
IC
GTATR
GTBTR
10 inserts in one case.

CUTTING CONDITIONS
SPARE PARTS
TECHNICAL DATA
D018
P001
Q001
D017
SMALL TOOLS
CTAH
LF
5.5
HF
H3
22
CUTDIA
SMALL TOOLS
15
Order Number
Stock
Dimensions (mm)
Insert Number
R L
*
*
CTAHR/L0810-120
a a
CTAHR/L1010-120
a a
CTAHR/L1212-120
a a
CTAHR/L1616-120
a a
CTAT
HF
LF
H3
pppp
10
120
12
pppp
10
10
10
120
12
pppp
12
12
12
120
pppp
16
16
16
120
CUTDIA
(mm)
12
(8) 1
*2
Clamp Screw
Wrench
NS402W
NKY15R
NS402W
NKY15R
NS403W
NKY15R
NS403W
NKY15R
1 When the width of cutting off (CW) is 0.7mm.

2 Clamp Torque (N m) : NS402W=1.0, NS403W=1.0
CTAH-S
5.5
16
LF
45
HF
H3
5.5
Order Number
Stock
15
CUTDIA
Dimensions (mm)
Insert Number
CTAHR1010-120S
CTAT
pppp
HF
LF
H3
10
10
10
80
12
CUTDIA
(mm)
12
(8) 1
*2
Clamp Screw
Wrench
NS401
NKY25R
the width of cutting off (CW) is 0.7mm.

*12 When
Clamp Torque (N m) : NS401=3.5
*

Work Material
Hardness
Grade
Feed (mm/rev)
180HB280HB
VP15TF/ VP15KZ
100 (50150)
0.05 (0.020.09)
Free Cutting Steel
VP15TF/ VP15KZ
110 (30180)
0.05 (0.010.09)
Stainless Steel
< 200HB
VP15TF/ VP15KZ
80 (50120)
0.03 (0.020.05)
Non-Ferrous Metal
VP15TF/ VP15KZ
150 (70230)
0.07 (0.030.11)
D018
Geometry
Insert Geometry
PDPT
CW 0.05
RE
16
RE
PDPT
CW 0.05
RE
With Breaker
16
RE
PDPT
CW 0.05
CW 0.05
20
CW 0.05
16
PDPT
PDPT
3.5
CW 0.05
RE
RE
PDPT
RE
CW 0.05
With Breaker
RE
RE
PDPT
CW 0.05
RE
RE
RE
Right hand
insert shown.
CW 0.05
20
Without Breaker
16
RE
CTAT 07080V5RR-B
CTAT 10120V5RR-B
CTAT 15120V5RR-B
CTAT 20120V5RR-B
CTAT 15120V5RR-BX
CTAT 20120V5RR-BX
R
R
R
R
R
R
CTAT 10120V5RN-B
CTAT 15120V5RN-B
CTAT 20120V5RN-B
N
N
N
CTAT 15120V5RN-BX
CTAT 20120V5RN-BX
N
N
CTAT 10110V5RL-B
CTAT 15110V5RL-B
CTAT 20110V5RL-B
L
L
L
CTAT 1012000RR
CTAT 1512000RR
CTAT 2012000RR
R
R
R
CTAT 07080V5LL-B
CTAT 10120V5LL-B
CTAT 15120V5LL-B
CTAT 20120V5LL-B
CTAT 10120V5LN-B
CTAT 15120V5LN-B
CTAT 20120V5LN-B
L
L
L
L
N
N
N
CTAT 10110V5LR-B
CTAT 15110V5LR-B
CTAT 20110V5LR-B
R
R
R
CTAT 1012000LL
CTAT 1512000LL
CTAT 2012000LL
L
L
L
a
a
a
0.7
1.0
1.5
2.0
4.5
6.7
6.7
6.7
0.05
0.05
0.05
0.05
8
12
12
12
1.5
2.0
6.7 0.05
6.7 0.05
12
12
1.0
1.5
2.0
6.7 0.05
6.7 0.05
6.7 0.05
12
12
12
1.5
2.0
6.7 0.05
6.7 0.05
12
12
1.0
1.5
2.0
6.7 0.05
6.7 0.05
6.7 0.05
11
11
11
1.0
1.5
2.0
6.7 0
6.7 0
6.7 0
12
12
12
0.7
1.0
1.5
2.0
4.5
6.7
6.7
6.7
0.05
0.05
0.05
0.05
8
12
12
12
1.0
1.5
2.0
6.7 0.05
6.7 0.05
6.7 0.05
12
12
12
1.0
1.5
2.0
6.7 0.05
6.7 0.05
6.7 0.05
11
11
11
1.0
1.5
2.0
6.7 0
6.7 0
6.7 0
12
12
12
Strong Edge Type
RE
RE
2.5
Without Breaker
50
20
RE
RE
16
Left Hand (L)
PDPT
RE
Hand
Strong Edge Type
RE
CW 0.05
Right Hand (R)
RE
Coated Dimensions (mm) CUTDIA1

(mm)
VP15TF CW PDPT RE
Order Number
SMALL TOOLS
Setting Geometry
Breaker
Holder
INSERTS
PDPT
3.5
PDPT
a
a
a
a
a
a
a
a
a
a
a
a
a
*1 CUTDIA : Max. Cut off Diameter
SPARE PARTS
TECHNICAL DATA
P001
Q001
D019
SMALL TOOLS
CTBH
LF
7.5
SMALL TOOLS
CUTDIA
Stock
Order Number
a a
CTBHR/L1212-160
a a
CTBHR/L1616-160
a a
19.5
CTBT

Dimensions (mm)
Insert Number
R L
CTBHR/L1010-160
H3
HF
25
HF
LF
H3
pppp
10
10
10
120
12
pppp
12
12
12
120
pppp
16
16
16
120
CUTDIA
(mm)
*
Clamp Screw
Wrench
16
NS402W
NKY15R
16
NS403W
NKY15R
16
NS403W
NKY15R
Setting Geometry
Breaker
Holder
INSERTS
Geometry
Insert Geometry
Right Hand (R)
CW 0.05
RE
16
CW 0.05
25
9.2
CW 0.05
9.4
45
RE
CW 0.05
Left Hand (L)
RE
D020
CW 0.05
Right hand
insert shown.
1.5
0.05
16
CTBT20160V5RR-B
2.0
0.05
16
CTBT20160V5RN-B
2.0
0.05
16
CTBT20160V5LL-B
2.0
0.05
16
CTBT20160V5LN-B
2.0
0.05
16
CTBT20145V5LR-B
2.0
0.05
14.5
9.2
RE
16
9.2
RE
CTBT15160V5RR-B
RE
RE
3.5
With Breaker
16
Hand
RE
RE
9.2
Coated Dimensions (mm) CUTDIA

(mm)
VP15TF CW
RE
Order Number
RE
9.2
CTCH
LF
CW
F2
Stock

Dimensions (mm)
Insert Number
R L
CTCHR/L1010-200
a a
CTCHR/L1212-200
a a
CTCT
CUTDIA
(mm)
HF
LF
F2
2ppp
10
10
10
120
11
20
NS501W HKY25RS
2ppp
12
12
12
120
11
20
NS501W HKY25RS
Clamp Screw
Wrench
SMALL TOOLS
Order Number
HF
C
U
TD
IA
0.5
Clamp Torque (N m) : NS501W=2.2
Order Number
Hand
CTCT22200V5N-B
CTCT2220001N-B
CTCT25200V5N-B
CTCT2520001N-B
CTCT22200V5R-B
CTCT2220001R-B
CTCT25200V5R-B
CTCT2520001R-B
CTCT22200V5L-B
CTCT2220001L-B
CTCT25200V5L-B
CTCT2520001L-B
* 10 inserts in one case.
Coated
VP15TF
*a
*a
*a
*a
*a
*a
*a
*a
*a
*a
*a
*a
Dimensions (mm)
CUTDIA
CW
PSIRR/L
RE
(mm)
2.2
0.05
20
2.2
0.1
20
2.5
0.05
20
2.5
0.1
20
2.2
17
0.05
20
2.2
17
0.1
20
2.5
17
0.05
20
2.5
17
0.1
20
2.2
17
0.05
20
2.2
17
0.1
20
2.5
17
0.05
20
2.5
17
0.1
20
Geometry
4.0
RE
10
CW 0.05
With Breaker
Breaker
INSERTS
90
RE
PSIRR
PSIRL
Neutral (N) Right Hand (R) Left Hand (L)

Work Material
Hardness
Grade
Feed (mm/rev)
180HB280HB
VP15TF
100 (50150)
0.05 (0.020.09)
Free Cutting Steel
VP15TF
110 (30180)
0.05 (0.010.09)
Stainless Steel
< 200HB
VP15TF
80 (50120)
0.03 (0.020.05)
Non-Ferrous Metal
VP15TF
150 (70230)
0.07 (0.030.11)
SPARE PARTS
TECHNICAL DATA
P001
Q001
D021
SMALL TOOLS
CTDH
LF
LH
0.5
Stock
HF
C
U
TD
IA
SMALL TOOLS
Order Number
CTDHR/L1616-280
CTDHR/L1616-350
a a
CTDT
Dimensions (mm)
Insert Number
CUTDIA
(mm)
R L
CTDHR/L1616-230
0.5
CW
F2
HF
LF
LH
F2
2535pp
16
16
16
125
24
12.2
23
HBH06020 HKY40R
2535pp
16
16
16
120
25
15
28
NS502W
2535pp
16
16
16
125
32
18.5
35
HBH06020 HKY40R
Clamp Screw
Wrench
HKY25R
Clamp Torque (N m) : HBH06020=7.0, NS502W=2.2
With Breaker
Order Number
Hand
Coated
Dimensions (mm)
VP15TF
CW
PSIRR
CUTDIA
RE
(mm)
CTDT2535002N-B
2.5
0.2
23 35
CTDT25350V5R-B
2.5
< 0.05
23 35
CTDT25350V5R-BS
2.5
17
< 0.05
23 35
CTDT2535002R-B
2.5
0.2
23 35
Geometry
6.39
90
CW 0.05
Breaker
INSERTS
D022
12
RE
PSIRR
Neutral (N)
RE
Right Hand (R)
CTEH
LF
LH
0.5
0.5
CW
F2
Stock
Dimensions (mm)
Insert Number
CTEHR/L1616-280
CTEHR/L1616-350
a a
CTET
CUTDIA
(mm)
R L
CTEHR/L1616-230
HF
LF
LH
F2
3035pp
16
16
16
125
24
12.2
23
HBH06020 HKY40R
3035pp
16
16
16
120
25
15
28
NS502W
3035pp
16
16
16
125
32
18.5
35
HBH06020 HKY40R
Clamp Screw Wrench
SMALL TOOLS
Order Number
HF
C
U
TD
IA
HKY25R
Clamp Torque (N m) : HBH06020=7.0, NS502W=2.2
Order Number
Hand
Coated
Dimensions (mm)
VP15TF
CW
PSIRR/L
CUTDIA
RE
(mm)
CTET30350V5R-B
< 0.05
23 35
CTET30350V5R-BS
17
< 0.05
23 35
CTET3035002N-B
0.2
23 35
CTET3035002R-B
0.2
23 35
CTET3035002L-B
0.2
2335
Geometry
6.39
90
CW 0.05
With Breaker
Breaker
INSERTS
RE
12
RE
PSIRL
PSIRR
Neutral (N) Right Hand (R) Left Hand (L)

Work Material
Hardness
Grade
Feed (mm/rev)
180HB280HB
VP15TF
100 (50150)
0.05 (0.020.09)
Free Cutting Steel
VP15TF
110 (30180)
0.05 (0.010.09)
Stainless Steel
< 200HB
VP15TF
80 (50120)
0.03 (0.020.05)
Non-Ferrous Metal
VP15TF
150 (70230)
0.07 (0.030.11)
SPARE PARTS
TECHNICAL DATA
P001
Q001
D023
SMALL TOOLS
EXTERNAL THREADING
TTAH
LF
HF
H3
6.5 (Maximum Step Difference)
SMALL TOOLS
15
Order Number
Stock
R L
a a
TTAHR/L1010
a a
TTAHR/L1212
a a
TTAHR/L1616
a a
TTAT
HF
LF
H3
Clamp Screw
Wrench
pppp
10
120
12
NS402W
NKY15R
pppp
10
10
10
120
12
NS402W
NKY15R
pppp
12
12
12
120
NS403W
NKY15R
pppp
16
16
16
120
NS403W
NKY15R
TTAT60075F5RR-B
0.4
TTAT60125V5RR-B
0.8
TTAT60075F5RL-B
0.4
TTAT60125V5RL-B
TTAT6015001RN-B
TTAT60075F5LR-B
0.05
0.2 0.75
(80 36)
0.05
0.5 1.25
(40 16)
0.05
0.2 0.75
(80 36)
0.8
0.05
0.5 1.25
(40 16)
1.25
0.1
1.0 1.5
(24 18)
0.4
0.05
0.2 0.75
(80 36)
TTAT60125V5LR-B
0.8
0.05
0.5 1.25
(40 16)
TTAT60075F5LL-B
0.4
0.05
0.2 0.75
(80 36)
TTAT60125V5LL-B
0.8
0.05
0.5 1.25
(40 16)
TTAT6015001LN-B
1.25
0.1
1.0 1.5
(24 18)
TTAT55158V5RR-B
0.8
0.05
(40 16)
TTAT55158V5RL-B
0.8
0.05
(40 16)
TTAT55158V5LR-B
0.8
0.05
(40 16)
TTAT55158V5LL-B
0.8
0.05
(40 16)
Flat
60
RE
60
PDX
Right Hand (R)
Hand
55
PDX
General Purpose
Partial Profile
(60)
Coated Dimensions (mm) Pitch of Screw

(mm)
VP15TF PDX
RE (thread/inch)
Order Number
55
Insert Geometry
55
Geometry
55
Setting Geometry
Breaker
INSERTS
Holder
TTAHR/L0810
Dimensions (mm)
Insert Number
PDX
60
2.5
RE
Flat
20.0
PDX
RE
60
PDX
Left Hand (L)
With Breaker
50
PDX
PDX
RE
RE
20.0
50
PDX
8.0
PDX
RE
Flat
RE
PDX
2.5
Left Hand (L) Right Hand (R)
General Purpose
Partial Profile
(55)
60
RE
Flat
60
8.0
RE
RE

Work Material
Hardness
Work Material
Hardness
180HB280HB
100 (50150)
110 (30180)
M Stainless Steel
N Non-Ferrous Metal
< 200HB
80 (50120)
150 (70230)
Free Cutting Steel

a
D024
HOLDER APPLICATION
Left Hand Holder
Left Hand Insert
SMALL TOOLS
Right Hand Insert
Right Hand Holder
*The above combinations enable to machine the side of p.

THREAD RANGE
Pitch
(mm)
Application range
Pitch Diameter of Thread (mm)
> &1.0
> &1.2
> &1.6
> &2.0
> &2.5
> &3.0
> &4.0
> &5.0
> &6.0
> &7.0
Number of
Passes
0.2
0.25
24
0.3
35
0.35
0.4
46
0.45
0.5
0.6
0.7
57
0.75
Threading
impossible
0.8
1
1.25
1.5
68
*Metric Thread (60)

Pitch(thread/inch)
Pitch Diameter of Thread
Inch
> &0.060 > &0.073 > &0.086 > &0.099 > &0.112 > &0.164 > &0.190 > &0.250 > &0.313
mm
> &1.524 > &1.854 > &2.184 > &2.515 > &2.845 > &4.166 > &4.826 > &6.350 > &7.938
80
72
Number of
Passes
35
64
46
56
48
44
40
57
32
28
26
24
20
18
16
Threading
impossible
68
*American UN, Whitworth

SPARE PARTS
TECHNICAL DATA
P001
Q001
D025
SMALL TOOLS
FOR OPPOSITE
(
EXTERNAL FRONT TURNING, COPYING, FACING TOOL POSTS )
SH
Finish
F3
WF
N
O
C
D
LU
F2
SMG
LF
93
Stock
SMALL TOOLS
SH16H-FSDUCL07
SH19K-FSDUCL07
SH20K-FSDUCL07
SH22K-FSDUCL07
SH25M-FSDUCL07
SH16H-FSDUCL11
SH19K-FSDUCL11
SH20K-FSDUCL11
SH22K-FSDUCL11
SH25M-FSDUCL11
DCON
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
(07, 11)
(07, 11)
(07, 11)
(07, 11)
Medium
Flat top
For nonferrous
metals
CBN/PCD
0702pp
11T3pp
AZ
(07, 11)
(07, 11)
(07, 11)
Dimensions (mm)
Insert Number
DCET
DCGT
DCGW
DCMT
DCMW
NP-DCGW
NP-DCMT
NP-DCMW
Medium
R-SN
Left hand tool holder shown.
Light
R-SS
R-SR
93
Order Number
Finish
R-F
LF
LU
WF
15.875 100
20
14
19.05
125
20
20
125
22
25.4
F2
(07, 11)
F3
Clamp Screw
Wrench
7.75 0.75
4.2
TS254
TKY08R
17
9.25 0.75
4.2
TS254
TKY08R
20
18
9.75 0.75
4.2
TS254
TKY08R
125
20
20
10.75 0.75
4.2
TS254
TKY08R
150
20
23
12.25 0.75
4.2
TS254
TKY08R
15.875 100
20
15
7.75 0.75
6.4
TS43
TKY15R
19.05
125
20
17
9.25 0.75
6.4
TS43
TKY15R
20
125
20
18
9.75 0.75
6.4
TS43
TKY15R
22
125
20
20
10.75 0.75
6.4
TS43
TKY15R
25.4
150
20
23
12.25 0.75
6.4
TS43
TKY15R
(Note 1) When using insert with right and left hand chip breaker, please use right hand insert.
(Note 2) The insert photos are only examples. The letters refer to the chip breaker and the dimension refers to the inscribed circle.

Work Material
Hardness
Grade
Feed (mm/rev)
180HB280HB
VP15TF
100 (50150)
0.08 (0.010.15)
VP15TF
110 (30180)
0.08 (0.010.15)
NX2525
150 (50250)
0.08 (0.010.15)
0.06 (0.020.1)
Free Cutting Steel
Stainless Steel
< 200HB
VP15TF
80 (50120)
Non-Ferrous Metal
HTi10
150 (70230)
D026
SHppp type inserts

CBN & PCD inserts
0.09 (0.030.15)
A132 A135
B043, B044, B060
CAM TOOL POSTS

1
0.1
HBKW
CSVH
20
HF
LF
Stock
Order Number
*1
Dimensions (mm)
Insert Number
R L
HF
LF
HBKW
*2
APMX
(mm)
Clamp Screw
Wrench
CSVHR/L0707
a a
pppp
140
0.5
3.0
NS251
NKY15R
CSVHR/L0808
a a
pppp
140
3.0
NS251
NKY15R
CSVHR/L0909
pppp
9.5
9.5
9.5
140
3.0
NS251
NKY15R
CSVHR/L1010
a a
pppp
10
10
10
140
3.0
NS251
NKY15R
CSVHR/L1212
pppp
12
12
12
140
3.0
NS251
NKY15R
CSVT
SMALL TOOLS
(Note 2) Max. Cutting Depth (APMX) varies depending on the type of insert used.
1 APMX : Max. Cutting Depth
2 Clamp Torque (N m) : NS251=1.0
*
*
INSERTS
CSVTF
Coated
Dimensions (mm)
VP15KZ
IC
RE
CF
PSIRR/L
APMX
(mm)
CSVTF30AR
CSVTF30AL
6.35
2.38
0.3
3.0
6.35
2.38
0.3
3.0
CSVTF30BR
6.35
2.38
0.3
3.0
CSVTF30CR
6.35
2.38
0.15
3.0
CSVTF30DR
6.35
2.38
0.15
3.0
CSVTF30AR-B
6.35
2.38
0.3
3.0
CSVTF30AL-B
6.35
2.38
0.3
3.0
CSVTF30BR-B
6.35
2.38
0.3
3.0
CSVTF30CR-B
CSVTF30DR-B
6.35
2.38
0.15
3.0
6.35
2.38
0.15
3.0
Geometry
Without Breaker
CF
Hand
RE
PSIRR
7
IC
30
With Breaker
RE
7
IC
CF
Order Number
Front turning
PSIRR
30
APMX : Max. Cutting Depth
CSVTFXL
Order Number
Hand
CSVTFXL
Front turning, Copying
Coated
Dimensions (mm)
VP15KZ
IC
RE
APMX
(mm)
6.35
2.38
3.0
Geometry
Without Breaker
RE
0.7
80
7
IC
S
45
* APMX : Max. Cutting Depth

SPARE PARTS
TECHNICAL DATA
P001
Q001
D027
SMALL TOOLS
CAM TOOL POSTS

INSERTS
RE
PDPT
CW
APMX
(mm)
R
R
a
a
6.35
6.35
2.38
2.38
0
0
2.0
2.5
0.6
0.7
1.5
2.0
CSVTC0640R
CSVTC0750R
CSVTC0750L
CSVTC0850R
CSVTC0850L
CSVTC0950R
CSVTC1060R
CSVTC1060L
CSVTC1360R
CSVTC1360L
CSVTC1560R
CSVTC1560L
CSVTC0640R-B
CSVTC0750R-B
CSVTC0850R-B
CSVTC0950R-B
CSVTC1060R-B
CSVTC1360R-B
CSVTC1560R-B
6.35
2.38
2.5
0.7
2.0
6.35
2.38
2.5
0.8
2.0
6.35
2.38
2.5
0.8
2.0
6.35
2.38
2.5
0.9
2.0
6.35
2.38
3.0
1.0
2.5
6.35
2.38
3.0
1.0
2.5
6.35
2.38
3.0
1.3
2.5
6.35
2.38
3.0
1.3
2.5
R
L
6.35
6.35
2.38
2.38
0
0
3.0
3.0
1.5
1.5
2.5
2.5
R
R
a
a
6.35
6.35
2.38
2.38
0
0
2.0
2.5
0.6
0.7
1.5
2.0
6.35
2.38
2.5
0.8
2.0
6.35
2.38
2.5
0.9
2.0
6.35
2.38
3.0
1.0
2.5
R
R
6.35
6.35
2.38
2.38
0
0
3.0
3.0
1.3
1.5
2.5
2.5
Geometry
Without Breaker
CW 0.05
Dimensions (mm)
IC
Hand
25
7
IC
RE
PDPT

With Breaker
CW 0.05
Coated
VP15KZ
Order Number
25
7
IC
RE
PDPT
CSVTB
Back turning
APMX
CF PSIRR/L (mm)
CSVTB10AR
CSVTB10AL
CSVTB10BR
CSVTB10CR
CSVTB10DR
CSVTB12AR
CSVTB14AR
CSVTB10AR-B
CSVTB10BR-B
CSVTB10CR-B
CSVTB10DR-B
CSVTB12AR-B
CSVTB14AR-B
R
L
a
a
6.35 2.38
6.35 2.38
0
0
2.5
2.5
1
1
0.3
0.3
5
5
2.0
2.0
6.35 2.38
2.5
0.3
2.0
6.35 2.38
2.5
0.15
2.0
6.35 2.38
2.5
0.15
2.0
R
R
6.35 2.38
6.35 2.38
0
0
2.5
2.5
1.2
1.4
0.3
0.3
5
5
2.0
2.0
R
R
a
a
6.35 2.38
6.35 2.38
0
0
2.5
2.5
1
1
0.3
0.3
5
2
2.0
2.0
6.35 2.38
2.5
0.15
2.0
6.35 2.38
2.5
0.15
2.0
R
R
6.35 2.38
6.35 2.38
0
0
2.5
2.5
1.2
1.4
0.3
0.3
5
5
2.0
2.0
VP15KZ
IC
RE
PDPT CW
Geometry
Without Breaker
45
CW 0.05
Dimensions (mm)
Hand
PSIRR
7
IC
RE
PDPT

With Breaker
45
CW 0.05
Coated
Order Number
CF
Cutting off
PSIRR
CF
SMALL TOOLS
CSVTC
7
IC
RE
PDPT

Order Number
Hand
CSVTBXL
Back turning, Copying
Coated
Dimensions (mm)
VP15KZ
IC
RE
APMX
(mm)
6.35
2.38
3.0
Geometry
Without Breaker
0.7
CSVTBXL
Expanded
View 45
RE
IC

a
D028
S
5
0.035
INSERTS
CSVTG
Dimensions (mm)
APMX
(mm)
IC
RE
PDPT
CW
6.35
2.38
0.5
0.25
0.15
6.35
2.38
0.5
0.3
0.15
CSVTG03505R
6.35
2.38
0.5
0.35
0.15
CSVTG04005R
6.35
2.38
0.5
0.4
0.15
CSVTG04510R
6.35
2.38
1.0
0.45
0.45
CSVTG05010R
6.35
2.38
1.0
0.5
0.45
CSVTG05510R
6.35
2.38
1.0
0.55
0.45
CSVTG06010R
6.35
2.38
1.0
0.6
0.45
CSVTG06510R
6.35
2.38
1.0
0.65
0.45
CSVTG07010R
6.35
2.38
1.0
0.7
0.45
CSVTG07520R
6.35
2.38
2.0
0.75
1.4
CSVTG07520L
6.35
2.38
2.0
0.75
1.4
CSVTG08020R
6.35
2.38
2.0
0.8
1.4
CSVTG08520R
6.35
2.38
2.0
0.85
1.4
CSVTG09020R
6.35
2.38
2.0
0.9
1.4
CSVTG09520R
6.35
2.38
2.0
0.95
1.4
CSVTG09520L
6.35
2.38
2.0
0.95
1.4
CSVTG10020R
6.35
2.38
2.0
1.0
1.4
CSVTG11030R
6.35
2.38
3.0
1.1
2.6
CSVTG12030R
6.35
2.38
3.0
1.2
2.6
CSVTG12030L
6.35
2.38
3.0
1.2
2.6
CSVTG13030R
6.35
2.38
3.0
1.3
2.6
CSVTG14030R
CSVTG15030R
6.35
2.38
3.0
1.4
2.6
6.35
2.38
3.0
1.5
2.6
Geometry
Without Breaker
SMALL TOOLS
CSVTG02505R
CSVTG03005R
Coated
VP15KZ
+0.03
CW +0
Hand
7
IC
RE
PDPT
CSVTT
Threading
CSVTT60050RR
CSVTT60050RL
Coated
Dimensions (mm)
Pitch
(mm)
IC
RE
0.2 0.5
6.35
2.38
0.03
0.2 0.5
6.35
2.38
0.03
VP15KZ
Geometry
Without Breaker
General Purpose
Partial Profile
(60)
7
IC
RR
60
3.0
RE
RL
0.35 0.05
Hand
60
3.0
1.0
Order Number
0.35 0.05
1.0
Order Number
Grooving
RE
SPARE PARTS
TECHNICAL DATA
P001
Q001
D029
SMALL TOOLS
BORING
SBAH
Without off set

LF
LU
15
HF
17.5
SMALL TOOLS

Order Number
Stock
Dimensions (mm)
Insert Number
*
*
SBAHR1022
SBAHR1222
SBAT
*1
LU
(mm)
DMIN
*2
(mm)
LF
HF
3080ppL/L-B
10
21.5
120
10
NS402W NKY15R
3080ppL/L-B
12
21.5
120
12
NS403W NKY15R
Clamp Screw Wrench
1 DMIN : Min. Cutting Diameter

2 Clamp Torque (N m) : NS402W=1.0, NS403W=1.0
SBAH
With off set

LF
HF
LU
S4
15
C5.0
Order Number
Stock
Dimensions (mm)
Insert Number
SBAHR1010
SBAT
LU
(mm)
3080ppL/L-B
LF
HF
S4
10
10
120
10
10
1
*
DMIN
*2
(mm)
Clamp Screw Wrench
NS402W NKY15R
: Min. Cutting Diameter

*12 DMIN
Clamp Torque (N m) : NS402W=1.0
*
Without Breaker
Order Number
Coated
Dimensions (mm)
VP15KZ
KAPR
SBAT308000L
95
SBAT3080V5L
95
DMIN
L19
(mm)
8.0
0.05
8.0
RE
Geometry
18.5
KAPR
12.0
Breaker
INSERTS
RE
95
8.0
SBAT3080V5L-B
95
0.05
8.0
L19
2.50
SBAT308000L-B
1.25
With Breaker
9.0
* DMIN : Min. Cutting Diameter
D030
SPARE PARTS
TECHNICAL DATA
P001
Q001
Memo
D031

OF BORING BARS
zOrganized by product series.

uses illustrations and arrows to depict available
machining applications along with cutting edge
lead angles.
TYPE OF BORING BAR

indicates the initial letters for the order number,
as well as applicable insert types.
GEOMETRY
TITLE OF PRODUCT SERIES

PRODUCT SECTION
CHIP BREAKER BY
CUTTING APPLICATION
PRODUCT FEATURES
BORING BARS
DIMPLE BAR
FSCLC/P
a Excellent vibration resistance due to light dimple head.

a Chip disposal is improved by having two channels for chip evacuation.
a A laser printed scale on the side for easy installation (Steel shank).
a l/d is 3 to 5 times the diameter (Carbide shank is 7 to 8 times the diameter).
CCooinserts, CPooinserts FP
Finish
Finish
(06,09)
Medium
95
Light
FM
MP
Light
LP
LM
(06,09)
(06,09)
Medium
PCD/CBN
FSTUP
TPooinserts
Finish
(06,09)
SV
(08,09)
Medium
MV
(08,09,11,16) (08,09,11,16)
PCD
93
MM
Light
FV
CBN
R/L-F
FSCLC1008R/L-06S=1
BORING
R L
FSCLC1008R/L-06S
a a
FSCLP1210R/L-08S
a a
FSCLP1412R/L-08S
a a
FSCLP1612R/L-09S
a a
FSCLP1816R/L-09S
a a
FSCLP2220R/L-09S
FSCLP3025R/L-09S
(06,09)
(06,09)
DCON
LF
LDRED WF
(06,08,09)
Dimensions(mm)
Insert Number
GAMF DMIN
RE
Maximum
recommendation
l/d
ratio Clamp
Order Number
(08,09,11,16)
GAMF DMIN
RE
Maximum
recommendation
l/d
ratio Clamp
Screw
Wrench
TKY06F
125 18
7.2 12
10
0.4
TS253 TKY08F
FSTUP1008R/L-08S
a a
0802pp
125
18
7.2
10
10
0.4
TS2D
150 22.5
12
0.4
3.5
TS3D
TKY10F
FSTUP1210R/L-09S
a a
0902pp
10
150
22.5
12
0.4
3.5
TS25D TKY08F
0802pp
12
150 27
11
14
0.4
TS3D
TKY10F
FSTUP1412R/L-09S
a a
0902pp
12
150
27
11
14
0.4
TS25D TKY08F
0903pp
12
150 30
11
16
0.4
TS4D
TKY15F
FSTUP1210R/L-11S
a a
1103pp
10
150
22.5
12
0.4
3.5
TS31D TKY10F
0903pp
16
180 36
15
3.5
18
0.4
TS4D
TKY15F
FSTUP1412R/L-11S
a a
1103pp
12
150
27
11
14
0.4
TS31D TKY10F
a a
0903pp
20
220 45
11
19
22
0.4
TS4D
TKY15F
FSTUP1816R/L-11S
a a
1103pp
16
180
36
15
18
0.4
TS31D TKY10F
a a
0903pp
25
250 56.3
15
23.4
30
0.4
TS4D
TKY15F
FSTUP2220R/L-11S
a a
1103pp
20
220
45
11
19
22
0.4
TS31D TKY10F
FSTUP3225R/L-16S
a a
1603pp
25
270
56.3
16
23.4
32
0.8
TS4D
CPMH
NP-CPGB
NP-CPMB
NP-CPMH
Carbide shank
with coolant hole
CCooinserts, CPooinserts
Finish
FP
Finish
Light
FM
Light
LP
LM
(06,09)
(06,09)
(06,09)
Medium
Medium
PCD/CBN
MP
(06,09)

Stock
FSCLC1008R/L-06E
a a
FSCLC1008R-06E-2/3
(06,09)
DCON
LF
LDRED WF
FSTUP-E
Carbide shank
with coolant hole
TPooinserts
Finish
RE
Maximum
recommendation
l/d
ratio Clamp
Screw

Wrench
0602pp
CCGH
CCMH
0602pp
NP-CCGT
NP-CCGW 0602pp
140
13.8
7.2 12
10
0.4
TS253 TKY08F
90
13.8
7.2 12
10
0.4
TS253 TKY08F
Order Number
Light
FV
SV
Medium
MV
(08,09)
(08,09,11)
PCD
CBN
(08,09,11)
R/L-F
(06,08,09)
GAMF DMIN
TKY15F
* Clamp Torque (N m) : TS2D=0.6, TS25D=1.0, TS31D=2.5, TS4D=3.5
93
(06,09)
Dimensions(mm)
Insert Number
R L
TPGH
TPMH
NP-TPGB
NP-TPMB
NP-TPMH
MM
FSCLC1008R/L-06E (-2/3, -1/2)=1
Stock
(08,09,11)
DCON
R L
LF
LDRED WF
(08,09,11)
Dimensions(mm)
Insert Number
GAMF DMIN
RE
Maximum
recommendation
l/d
ratio Clamp
Screw
Wrench
a a
0802pp
140
13.8
7.2
10
10
0.4
TS2D
TKY06F
90
13.8
7.2
10
10
0.4
TS2D
TKY06F
TKY06F
FSCLC1008R-06E-1/2
70
13.8
7.2 12
10
0.4
TS253 TKY08F
FSTUP1008R/L-08E
FSCLP1210R/L-08E
a a
0802pp
10
160
16.0
12
0.4
7.5
TS3D
TKY10F
FSTUP1008R-08E-2/3
0802pp
FSCLP1210R-08E-2/3
0802pp
10
105
16.0
12
0.4
7.5
TS3D
TKY10F
FSTUP1008R-08E-1/2
0802pp
70
13.8
7.2
10
10
0.4
TS2D
FSCLP1210R-08E-1/2
0802pp
10
80
16.0
12
0.4
7.5
TS3D
TKY10F
FSTUP1210R/L-09E
a a
0902pp
10
160
16.0
12
0.4
7.5
TS25D TKY08F
FSCLP1412R/L-08E
a a
0802pp
12
180
17.8
11
14
0.4
TS3D
TKY10F
FSTUP1210R-09E-2/3
0902pp
10
105
16.0
12
0.4
7.5
TS25D TKY08F
FSCLP1412R-08E-2/3
0802pp
12
120
17.8
11
14
0.4
TS3D
TKY10F
FSTUP1210R-09E-1/2
0902pp
10
80
16.0
12
0.4
7.5
TS25D TKY08F
FSCLP1412R-08E-1/2
0802pp
12
90
17.8
11
14
0.4
TS3D
TKY10F
FSTUP1412R/L-09E
a a
0902pp
12
180
17.8
11
14
0.4
TS25D TKY08F
FSCLP1816R/L-09E
a a
0903pp
16
220
21.8
15
3.5
18
0.4
TS4D
TKY15F
FSTUP1412R-09E-2/3
0902pp
12
120
17.8
11
14
0.4
TS25D TKY08F
0902pp
12
90
17.8
11
14
0.4
TS25D TKY08F
CPMH
NP-CPGB
NP-CPMB
NP-CPMH
TPGH
TPMH
NP-TPGB
NP-TPMB
NP-TPMH
FSCLP1816R-09E-2/3
0903pp
16
145
21.8
15
3.5
18
0.4
TS4D
TKY15F
FSTUP1412R-09E-1/2
FSCLP1816R-09E-1/2
0903pp
16
110
21.8
15
3.5
18
0.4
TS4D
TKY15F
FSTUP1816R/L-11E
a a
1103pp
16
220
21.8
15
18
0.4
TS31D TKY10F
FSCLP2220R/L-09E
a a
0903pp
20
250
24.0
11
19
22
0.4
TS4D
TKY15F
FSTUP1816R-11E-2/3
1103pp
16
145
21.8
15
18
0.4
TS31D TKY10F
FSCLP2220R-09E-2/3
0903pp
20
165
24.0
11
19
22
0.4
TS4D
TKY15F
FSTUP1816R-11E-1/2
1103pp
16
110
21.8
15
18
0.4
TS31D TKY10F
FSCLP2220R-09E-1/2
0903pp
20
125
24.0
11
19
22
0.4
TS4D
TKY15F
FSTUP2220R/L-11E
a a
1103pp
20
250
24.0
11
19
22
0.4
TS31D TKY10F
FSTUP2220R-11E-2/3
1103pp
20
165
24.0
11
19
22
0.4
TS31D TKY10F
FSTUP2220R-11E-1/2
1103pp
20
125
24.0
11
19
22
0.4
TS31D TKY10F
Clamp Torque (N m) : TS253=1.0, TS3D=2.5, TS4D=3.5

(Note 2) When using insert with right and left hand chip breaker, please use left hand
insert for right hand holder and right hand insert for left hand holder.
CCpp type inserts
A126 A130
CPpp type inserts
A131
CBN & PCD inserts
B039 B042, B059
* Clamp Torque (N m) : TS2D=0.6, TS25D=1.0, TS31D=2.5
LEGEND FOR STOCK

STATUS MARK
REFERENCE PAGE
is shown on the left hand page

indicates reference pages for

details of inserts that are
applicable to the title product.
PRODUCT STANDARDS
minimum cutting diameters,
standard corner radius,
recommended l/d ratios,
and spare parts.
MIN. CUTTING DIAMETER

is colour-coded to let you find, at a
glance, the maximum / minimum cutting
diameters for internal machining.

E000
LDRED WF
10
95
E006
LF
0602pp
FSCLC/P-E
DCON
0802pp
* Clamp Torque (N m) : TS253=1.0, TS3D=2.5, TS4D=3.5
Order Number
Insert Number
R L
Wrench
Screw
CCG/MH
NP-CCGT
NP-CCGW
(08,09,11)
Dimensions(mm)
Stock
BORING

Stock
Order Number
CUTTING CONDITIONS
TPpp type inserts
CBN & PCD inserts
A145 A147
B046, B062
SPARE PARTS
TECHNICAL DATA
E012
P001
Q001
E007
PAGE REFERENCE
SPARE PARTS
TECHNICAL DATA
TURNING TOOLS
BORING BARS
CLASSIFICATION OF BORING TOOLS .......... E002
IDENTIFICATION .............................................. E004
STANDARD BORING BARS
FEATURES OF DIMPLE BAR ...................... E005
DIMPLE BAR................................................. E006
DOUBLE CLAMP DIMPLE BAR................... E013
MICRO-DEX BORING BARS ........................ E016
MICRO-MINI TWIN BORING BARS ............. E019
MICRO-MINI BORING BARS........................ E022
F TYPE BORING BARS ................................ E025
S TYPE BORING BARS................................ E028
P TYPE BORING BARS................................ E035
D TYPE BORING HEAD ............................... E039
AL TYPE BORING BARS ............................. E042
Arranged by Alphabetical order

*E013
E017 CpppSTUC
Appp-DCLN
E013
E014
E014
E015
E015
E036
E037
E036
E038
E035
E035
E037
E022
E016
E030
E031
E029
E028
Appp-DDUN
Appp-DSKN
Appp-DTFN
Appp-DVUN
Appp-DWLN
ApppPCLN
ApppPDQN
ApppPDUN
ApppPDZN
ApppPSKN
ApppPTFN
ApppPWLN
Cpppp-BLS
CpppSCLC
CpppSCLC
CpppSDQC
CpppSDUC
CpppSTFC
E032
E016
E019
E020
E040
E040
E039
E039
E041
E026
E026
E006
E009
E008
E025
E025
E007
E012
CpppSVQC
CpppSWUB
CB
CR
DPCL
DPDH
DPDU
DPTF
DPVP
FCTU1
FCTU2
FSCLC/P
FSDQC
FSDUC
FSTU1
FSTU2
FSTUP
FSVJB/C
E011
E011
E027
E027
E010
E018
E023
E030
E034
E031
E029
E033
E028
E042
E032
E033
E024
FSVPB/C
FSVUB/C
FSWL1
FSWL2
FSWUB/P
RBH
RBH
SpppSCLC
SpppSCZC
SpppSDQC
SpppSDUC
SpppSSKC
SpppSTFC
SpppSTFE
SpppSVQC
SpppSVUC
SBH
E001
BORING BARS
CLASSIFICATION
KAPR=75 KAPR=91
Name of Tool Holder
DIMPLE BAR
Features
a
a
a
a
BORING
DOUBLE CLAMP
DIMPLE BAR
a
a
a
a
F Type Boring Bars
a
a
a
a
a
S Type Boring Bars
a
a
a
a
a
P Type Boring Bars
a
a
a
a
a
D Type Boring Head
a
a
a
a
The minimum cutting diameter is

from &10.
5, 7, 11 positive insert.
Excellent vibration resistance due
to a light dimple head.
l/d is 3 to 5 times the diameter
(Carbide shank is 7 to 8 times the
diameter).
from &32.
Economical negative insert.
Single action type.
Excellent vibration resistance due
to a light dimple head.
(With coolant hole.)
l/d is 3 to 4 times the diameter.
KAPR
KAPR
^ E007
DSKN
^ E014
DTFN
^ E014
a
a
a
a
a
a
MICRO-DEX
Boring Bars
(Carbide Shank)
a
a
^ E033

from &25.
ISO standard.
Lever lock type, and pin lock type.
l/d is 3 times the diameter.
^ E035
a
a
a
a
MICRO-MINI TWIN
Boring Bars
a
a
a
a
MICRO-MINI
Boring Bars
a
a
a
a
The minimum cutting diameter is from &5.

7positive insert.
Carbide shank type.
Easy-to-use tool geometries.
Suitable for small workpieces.
^ E013
FSTU

ISO standard.
7positive insert.
Screw-on type.
l/d is 3 to 5 times the diameter
(Carbide shank is 7 times the diameter).

Suitable for non-ferrous metal.
20positive insert.
Screw-on type.
Excellent vibration resistance.
DDUN
^ E025
SSKC
PSKN
STFC
^ E028
PTFN
^ E035
DPTF
^ E039
AL Type Boring Bars
KAPR
FSTUP

from &5.8.
11positive insert.
Screw-on type and Clamp-on type.
l/d is 3 to 5 times the diameter.
FSWL type is 7positive insert.

from &40.
Lever lock type.
Exchangeable head type.
KAPR=93
SDUC
^ E029
FSDUC
^ E008
DVUN
^ E015
FCTU
^ E026
SVUC
^ E033
PDUN
^ E036
DPDU
^ E039
STFE
^ E042
SWUB
^ E016
STUC
^ E017

from &2.2.
Solid carbide type with two cutting
edges.
Continuous cutting from boring to facing.
With or without a chip breaker.
from &3.2.
Solid carbide type (Single cutting edges).
Cutting edge can be shaped
according to the application. Thus,
it covers a wide cutting range
(threading,grooving,copying, etc.).
CooFR-BLS
^ E022
(Note 1) Holders with blue colour symbol have an anti-vibration carbide shank. (For Micro-dex boring bars, carbide shank only.)
E002
FSVUB/C
^ E011
^ E010
FSCLC/P
FSDQC
^ E006
DCLN
^ E013
^ E009
FSVPB/C
^ E011
Small Diameter
Cutting
Specialized
Coolant Hole
Vibration
Resisiance
Operation
Efficiency
KAPR
Selection Standard
Clamp Rigidity
KAPR
KAPR
KAPR
KAPR
e e e
FSVJB/C
^ E012
BORING
FSWUB/P
KAPR=10730 11730 KAPR=142 KAPR=3,5

Low Cutting Resistance (Sharpness)
KAPR
KAPR=95
Economical
KAPR=93
DWLN
^ E015
FSWL
^ E027
SCLC
SDQC
^ E030
PCLN
^ E036
DPCL
^ E040
^ E031
PWLN
^ E037
SVQC
SCZC
^ E032
^ E034
PDQN
DPDH
e e
PDZN
^ E037
^ E040
^ E038
DPVP
^ E041
SCLC
^ E016
e
CBooRS(-B)
^ E019
CR
^ E020
(Note 2) e : 1st recommendation. u: 2nd recommendation.

(Note 3) Indicates that the shank material is carbide.
E003
BORING BARS
IDENTIFICATION
y DIMPLE BAR
nMin.Cutting Diameter
cInsert Shape
zFunction
BORING
Screw-on
vCutting Angle
Right Hand
Left Hand
16
16 16
34 34
20
20
18 18
40 40
25
25
11
20 20
32
32
10730
RHOMBIC 35
11730
TRIGON
142
bInsert Clearance
10
08
RHOMBIC 55
10
12
TRIANGULAR 60
10
16
RHOMBIC 80
25 25
12
95
6.35
12 12
30 30
93
.Cutting Edge Length (mm)
08
32 32
RHOMBIC 55
Inscribed circle 4.76 5.56

of insert
22 22
13 13
RHOMBIC 80
,Hand of Tool
R - 06
11
u
E - 2/3
11 Tool Length (Carbide shank only) (mm)

u
/Shank Material
7.94 9.525
Carbide Shank
Shank Dia.
10
12
16
20
Steel Shank
No symbol 140 160
180
220
250
120
145
165
90
110
125
06
0.8
09
07
11
2/3
90 105
TRIANGULAR 60 08
09
11
16
1/2
70
RHOMBIC 35 08
11
16
L3
04
06
TRIGON
(mm)
10 10
14 14
xClamp Structure
F Fixed type
mShank Diameter
(mm)
80
y ISO TYPE Boring tools
[For Aluminium Alloy, P-type and S-type]
16
L
n
C
m
09
cTool Length
zShank Material
Steel Shank
A with Coolant Hole
vClamp Structure
bInsert Shape
,Hand of Tool
Lever Lock
RHOMBIC 80
7Positive
Right Hand
100
Screw-on
RHOMBIC 55
20Positive
Left Hand
125
SQUARE 90
11Positive
Carbide Shank
Carbide Shank
with Coolant Hole
150
TRIANGULAR 60
Steel Shank
180
RHOMBIC 35
200
TRIGON
250
(mm)
mInsert Clearance
80
xShank Diameter
E004
(mm)
300
350
400
nCutting Angle
.Cutting Edge Length (mm)
08
91
Inscribed circle
of insert
10
10
75
RHOMBIC 80 06
08
09
12
12
12
95
RHOMBIC 55 07
11
15
16
16
09
12
19
20
20
TRIANGULAR 60 11
16
22
25
25
RHOMBIC 35 11
16
32
32
40
40
10730
93
SQUARE 90
6.35 7.94 9.525 12.70 19.05

19
FEATURES OF DIMPLE BAR

Highly rigid steel shank and a lightweight head configuration
designed by computer simulation analysis reduces chatter
and improves the vibration damping properties.
Chip disposal is improved by having

two channels for chip evacuation.
The lightweight head with its large
dimple reduces chatter.
The boring bar has a laser printed

scale on the shank to facilitate easy
installation.
"F and FS" breakers improves the quality
of the surface finish, "MV" breaker offers
excellent chip disposal. High wear
resistant CBN inserts are also available
for the machining of hardened materials.
y DEFLECTION RESISTANCE
BORING
Available in sizes smaller than the ISO

standard. Therefore the boring of
small diameter holes is possible.
y VIBRATION RESISTANCE
a DIMPLE BAR
Weight of the
Head
49.7g
Damping Time
15.8ms
Cutting Force
(Principal Force)
Cutting Force
(Back Force)
By reducing the weight of the head, the damping

properties are increased.
a Conventional Product
The unique cross sectional

shape engineered into the
dimple effectively balances
the cutting forces (principal
and back force), and reduces
deflection by up to 17 %.
Boring Bar
DIMPLE BAR
Conventional Bar
Weight of the
Head
70.1g
Damping Time
20ms
Deflection
28.3!m
34!m
simulation data stated above was conducted with a FSCLP1816R-09S holder, under the following conditions;
* The
l/d=5, depth of cut=0.5mm, and feed=0.05mm/rev.
y Direction for the use of CCG/MT CPG/MT CPMX TPG/MX type inserts
By changing the clamp screw, it is possible to use the inserts listed in the table below.
Holder : FSCLC/P FSCLC/P...E

Insert Number
Clamp Screw
Holder : FSTUP FSTUP...E

Insert Number
Clamp Screw
CCG/MT0602oo (& 6.35)
Can be used as it is.
TPG/MX0802oo (& 4.76)
Change to CS200T
CPG/MT0802oo (& 7.94)
Change to TS3
TPG/MX0902oo (& 5.56)
Change to CS250T
CPG/MT0903oo (& 9.525)
Change to TS4
TPG/MX1103oo (& 9.525)
Change to CS300890T
CPMX0802oo (& 7.94)
CPMX0903oo (& 9.525)
If the screw is too long the please shorten as necessary.

*(Note
) TPMT/W09, W11 types cannot be used due to a different clamp screw size.
E005
BORING BARS
DIMPLE BAR
FSCLC/P

Finish
FP
Finish
FM
Light
LP
Light
LM
WF
95
95
GAMF RE LDRED
DMIN 5
H
DCON
LF
(06,09)
(06,09)
(06,09)
Medium
Medium
PCD/CBN
MP
(06,09)
MM
FSCLC1008R/L-06S=1
Order Number
Stock
Insert Number
R L
BORING
(06,09)
(06,09)
DCON
LF
LDRED WF
(06,08,09)
Dimensions(mm)
GAMF DMIN
RE
Maximum
recommendation
l/d
ratio Clamp
Wrench
Screw
CCG/MH
NP-CCGT
NP-CCGW
FSCLC1008R/L-06S
a a
0602pp
FSCLP1210R/L-08S
a a
0802pp
FSCLP1412R/L-08S
a a
0802pp
FSCLP1612R/L-09S
a a
FSCLP1816R/L-09S
a a
FSCLP2220R/L-09S
FSCLP3025R/L-09S
125 18
7.2 12
10
0.4
TS253 TKY08F
10
150 22.5
12
0.4
3.5
TS3D
TKY10F
12
150 27
11
14
0.4
TS3D
TKY10F
0903pp
12
150 30
11
16
0.4
TS4D
TKY15F
0903pp
16
180 36
15
3.5
18
0.4
TS4D
TKY15F
a a
0903pp
20
220 45
11
19
22
0.4
TS4D
TKY15F
a a
0903pp
25
250 56.3
15
23.4
30
0.4
TS4D
TKY15F
CPMH
NP-CPGB
NP-CPMB
NP-CPMH
* Clamp Torque (N m) : TS253=1.0, TS3D=2.5, TS4D=3.5
FSCLC/P-E
Carbide shank
with coolant hole
Finish
FP
Finish
FM
Light
LP
Light
LM
WF
95
95
GAMF RE LDRED
DMIN 5
H
DCON
LF
(06,09)
(06,09)
(06,09)
Medium
Medium
PCD/CBN
MP
(06,09)
MM
FSCLC1008R/L-06E (-2/3, -1/2)=1

Order Number
Stock
Insert Number
R L
E006
FSCLC1008R/L-06E
a a
FSCLC1008R-06E-2/3
FSCLC1008R-06E-1/2
FSCLP1210R/L-08E
(06,09)
(06,09)
DCON
LF
LDRED WF
(06,08,09)
Dimensions(mm)
GAMF DMIN
RE
Maximum
recommendation
l/d
ratio Clamp
Screw
0602pp
Wrench
CCGH
CCMH
0602pp
NP-CCGT
NP-CCGW 0602pp
140
13.8
7.2 12
10
0.4
TS253 TKY08F
90
13.8
7.2 12
10
0.4
TS253 TKY08F
70
13.8
7.2 12
10
0.4
TS253 TKY08F
a a
0802pp
10
160
16.0
12
0.4
7.5
TS3D
TKY10F
FSCLP1210R-08E-2/3
0802pp
10
105
16.0
12
0.4
7.5
TS3D
TKY10F
FSCLP1210R-08E-1/2
0802pp
10
80
16.0
12
0.4
7.5
TS3D
TKY10F
FSCLP1412R/L-08E
a a
0802pp
12
180
17.8
11
14
0.4
TS3D
TKY10F
FSCLP1412R-08E-2/3
0802pp
12
120
17.8
11
14
0.4
TS3D
TKY10F
FSCLP1412R-08E-1/2
0802pp
12
90
17.8
11
14
0.4
TS3D
TKY10F
FSCLP1816R/L-09E
a a
0903pp
16
220
21.8
15
3.5
18
0.4
TS4D
TKY15F
FSCLP1816R-09E-2/3
0903pp
16
145
21.8
15
3.5
18
0.4
TS4D
TKY15F
FSCLP1816R-09E-1/2
0903pp
16
110
21.8
15
3.5
18
0.4
TS4D
TKY15F
FSCLP2220R/L-09E
a a
0903pp
20
250
24.0
11
19
22
0.4
TS4D
TKY15F
FSCLP2220R-09E-2/3
0903pp
20
165
24.0
11
19
22
0.4
TS4D
TKY15F
FSCLP2220R-09E-1/2
0903pp
20
125
24.0
11
19
22
0.4
TS4D
TKY15F
CPMH
NP-CPGB
NP-CPMB
NP-CPMH
Clamp Torque (N m) : TS253=1.0, TS3D=2.5, TS4D=3.5

CCpp type inserts
A126 A130
CPpp type inserts
A131
CBN & PCD inserts
B039 B042, B059
FSTUP
TPooinserts
Finish
93
LDRED
H
LF
DCON
Insert Number
DCON
R L
(08,09,11)
LF
LDRED WF
FSTUP1008R/L-08S
a a
0802pp
125
18
7.2
FSTUP1210R/L-09S
a a
0902pp
10
150
22.5
FSTUP1412R/L-09S
a a
0902pp
12
150
27
FSTUP1210R/L-11S
a a
1103pp
10
150
FSTUP1412R/L-11S
a a
1103pp
12
FSTUP1816R/L-11S
a a
1103pp
FSTUP2220R/L-11S
a a
FSTUP3225R/L-16S
a a
TPGH
TPMH
NP-TPGB
NP-TPMB
NP-TPMH
(08,09,11,16)
Dimensions(mm)
Stock
CBN
R/L-F

Order Number
(08,09,11,16) (08,09,11,16)
PCD
RE
Medium
MV
GAMF DMIN
RE
Maximum
recommendation
l/d
ratio Clamp
Screw
Wrench
TKY06F
10
10
0.4
TS2D
12
0.4
3.5
TS25D TKY08F
11
14
0.4
TS25D TKY08F
22.5
12
0.4
3.5
TS31D TKY10F
150
27
11
14
0.4
TS31D TKY10F
16
180
36
15
18
0.4
TS31D TKY10F
1103pp
20
220
45
11
19
22
0.4
TS31D TKY10F
1603pp
25
270
56.3
16
23.4
32
0.8
TS4D
BORING
GAMF
DMIN
SV
(08,09)
WF
93
Light
FV
TKY15F
Clamp Torque (N m) : TS2D=0.6, TS25D=1.0, TS31D=2.5, TS4D=3.5
FSTUP-E
Carbide shank
with coolant hole
TPooinserts
Finish
Light
FV
SV
Medium
MV
WF
93
93
GAMF
DMIN
RE
LDRED
Stock
(08,09,11)
Insert Number
DCON
LF
(08,09,11)
LDRED WF
(08,09,11)
Dimensions(mm)
R L
CBN
DCON

Order Number
(08,09,11)
PCD
R/L-F
LF
(08,09)
GAMF DMIN
RE
Maximum
recommendation
l/d
ratio Clamp
Screw
Wrench
FSTUP1008R/L-08E
a a
0802pp
140
13.8
7.2
10
10
0.4
TS2D
TKY06F
FSTUP1008R-08E-2/3
0802pp
90
13.8
7.2
10
10
0.4
TS2D
TKY06F
FSTUP1008R-08E-1/2
0802pp
70
13.8
7.2
10
10
0.4
TS2D
TKY06F
FSTUP1210R/L-09E
a a
0902pp
10
160
16.0
12
0.4
7.5
TS25D TKY08F
FSTUP1210R-09E-2/3
0902pp
10
105
16.0
12
0.4
7.5
TS25D TKY08F
FSTUP1210R-09E-1/2
0902pp
10
80
16.0
12
0.4
7.5
TS25D TKY08F
0902pp
12
180
17.8
11
14
0.4
TS25D TKY08F
0902pp
12
120
17.8
11
14
0.4
TS25D TKY08F
0902pp
12
90
17.8
11
14
0.4
TS25D TKY08F
TPGH
TPMH
NP-TPGB
NP-TPMB
NP-TPMH
FSTUP1412R/L-09E
a a
FSTUP1412R-09E-2/3
FSTUP1412R-09E-1/2
FSTUP1816R/L-11E
a a
1103pp
16
220
21.8
15
18
0.4
TS31D TKY10F
FSTUP1816R-11E-2/3
1103pp
16
145
21.8
15
18
0.4
TS31D TKY10F
FSTUP1816R-11E-1/2
1103pp
16
110
21.8
15
18
0.4
TS31D TKY10F
FSTUP2220R/L-11E
a a
1103pp
20
250
24.0
11
19
22
0.4
TS31D TKY10F
FSTUP2220R-11E-2/3
1103pp
20
165
24.0
11
19
22
0.4
TS31D TKY10F
FSTUP2220R-11E-1/2
1103pp
20
125
24.0
11
19
22
0.4
TS31D TKY10F
Clamp Torque (N m) : TS2D=0.6, TS25D=1.0, TS31D=2.5

CUTTING CONDITIONS
TPpp type inserts
CBN & PCD inserts
A145 A147
B046, B062
SPARE PARTS
TECHNICAL DATA
E012
P001
Q001
E007
BORING BARS
DIMPLE BAR

FSDUC
DCooinserts
Finish
FP
WF
93
GAMF
DMIN
RE
H
DCON
F2
93
LDRED
LF
Stock
BORING
R L
FSDUC1410R/L-07S
a a
FSDUC1612R/L-07S
a a
FSDUC2016R/L-07S
a a
FSDUC3220R/L-11S
a a
DCMT
DCET
DCGT
NP-DCMT
NP-DCMW
DCON LF LDRED WF
F2
Light
LM
(07,11)
(07,11)
(07,11)
(07,11)
Medium
PCD
CBN
MP
MM
(07,11)
R/L-F
(07,11)
(07,11)
(07,11)
Dimensions(mm)
Insert Number
Light
LP
Medium

Order Number
Finish
FM
Maximum
recommendation
l/d
GAMF DMIN RE ratio
Clamp
Screw
Wrench
7.5
14
0.4
3.5
TS25
TKY08F
0702pp
10
150 18
8.3 3.3
0702pp
12
150 20
9.3 3.3
11
16
0.4
TS25
TKY08F
0702pp
16
180 20
11.3 3.3
15
20
0.4
TS25
TKY08F
11T3pp
20
180 22.5 16.1 6.1
19
32
0.8
TS43
TKY15F
FSDUC-E
Carbide shank
with coolant hole
DCooinserts
Finish
FP
Finish
FM
Light
LP
Light
LM
WF
93
GAMF
DMIN
RE
H
DCON
F2
93
LDRED
LF
(07,11)
(07,11)
(07,11)
(07,11)
Medium
Medium
PCD
CBN
MP

Order Number
Stock
R L
FSDUC1410R/L-07E
a a
FSDUC1612R/L-07E
a a
FSDUC2016R/L-07E
a a
FSDUC3220R/L-11E
a a
(07,11)
Dimensions(mm)
Insert Number
DCMT
DCET
DCGT
NP-DCMT
NP-DCMW
DCON LF LDRED WF
F2
MM
R/L-F
(07,11)
(07,11)
(07,11)
Maximum
recommendation
l/d
GAMF DMIN RE ratio
Clamp
Screw
Wrench
0702pp
10
160 16.0
8.3
3.3
7.5
14
0.4
7.5
TS25
TKY08F
0702pp
12
180 17.8
9.3
3.3
11
6.0
16
0.4
TS25
TKY08F
0702pp
16
220 21.8 11.3
3.3
15
5.0
20
0.4
TS25
TKY08F
11T3pp
20
250 24.0 16.1
6.1
19
5.0
32
0.8
TS43
TKY15F
a
E008
DCpp type inserts

CBN & PCD inserts
A132 A135
B043, B044, B060
FSDQC
Finish
DCooinserts
FP
Finish
FM
Light
LP
Light
LM
RE
DMIN
LDRED
(07,11)
(07,11)
(07,11)
Medium
PCD
CBN
MP
H
DCON
LF
(07,11)
Medium

Order Number
Stock
R L
FSDQC1310R/L-07S
a a
FSDQC1612R/L-07S
a a
FSDQC2016R/L-07S
a a
FSDQC2520R/L-11S
a a
(07,11)
DCMT
DCET
DCGT
NP-DCMT
NP-DCMW
DCON LF LDRED WF
F2
R/L-F
(07,11)
(07,11)
(07,11)
Dimensions(mm)
Insert Number
MM
Maximum
recommendation
l/d
GAMF DMIN RE ratio
Clamp
Screw
Wrench
0702pp
10
150 20.5
7.6
2.6
13
0.4
3.5
TS25
TKY08F
0702pp
12
150 22.5
8.6
2.6
11
16
0.4
TS25
TKY08F
0702pp
16
180 22.5 10.6
2.6
15
20
0.4
TS25
TKY08F
11T3pp
20
180 26
3.7
19
25
0.8
TS43
TKY15F
13.7
BORING
GAMF
F2
107
30
WF
10730
FSDQC-E
Carbide shank
with coolant hole
Finish
DCooinserts
FP
Finish
FM
Light
LP
Light
LM
GAMF
DMIN
RE
LDRED
LF
(07,11)
(07,11)
(07,11)
(07,11)
Medium
Medium
PCD
CBN
H
MP
DCON
F2
107
30
WF
10730

Order Number
Stock
R L
FSDQC1310R/L-07E
a a
FSDQC1612R/L-07E
a a
FSDQC2016R/L-07E
a a
FSDQC2520R/L-11E
a a
(07,11)
Dimensions(mm)
Insert Number
DCMT
DCET
DCGT
NP-DCMT
NP-DCMW
DCON LF LDRED WF
F2
MM
R/L-F
(07,11)
(07,11)
(07,11)
Maximum
recommendation
l/d
GAMF DMIN RE ratio
Clamp
Screw
Wrench
0702pp
10
162 18.4
7.6
2.6
13
0.4
7.5
TS25
TKY08F
0702pp
12
182 20.2
8.6
2.6
11
16
0.4
TS25
TKY08F
0702pp
16
222 24.2 10.6
2.6
15
20
0.4
TS25
TKY08F
11T3pp
20
254 28.0 13.7
3.7
19
25
0.8
TS43
TKY15F
CUTTING CONDITIONS
DCpp type inserts
CBN & PCD inserts
A132 A135
B043, B044, B060
SPARE PARTS
TECHNICAL DATA
E012
P001
Q001
E009
BORING BARS
DIMPLE BAR

FSWUB/P
WBooinserts, WPooinserts
Finish
R/L-FFS
93
(L3,04,06)
Medium
WF
93
GAMF
LDRED
RE
H
DCON
LF
DMIN
The &8 and & 10 shanks are 0
Order Number
Insert Number
DCON
BORING
R L
FSWUB1008R/L-L3S
a a
FSWUB1210R/L-L3S
a a
LF
LDRED WF
(L3,04,06)
Dimensions(mm)
Stock
MV
GAMF DMIN
RE
Maximum
recommendation
l/d
ratio Clamp
Screw
Wrench
L302pp
125
18
7.2
14
10
0.2
TS2
TKY06F
L302pp
10
150
22.5
11
12
0.2
3.5
TS2
TKY06F
FSWUP1412R/L-04S
a a
0402pp
12
150
27
11
14
0.4
TS253 TKY08F
FSWUP1816R/L-04S
a a
0402pp
16
180
36
15
18
0.4
TS253 TKY08F
FSWUP2220R/L-06S
a a
0603pp
20
220
45
11
19
22
0.8
TS4
TKY15F
FSWUP3025R/L-06S
a a
0603pp
25
250
56.3
15
23.4
30
0.8
TS4
TKY15F
WBMT
WBGT
WPMT
WPGT
FSWUB/P-E
Carbide shank
with coolant hole
WBooinserts, WPooinserts
Finish
R/L-FFS
93
WF
(L3,04,06)
93
GAMF
DMIN
RE
Medium
H
LDRED
LF
MV
DCON
The & 8 and & 10 shanks are 0
Order Number
Stock
Insert Number
R L
DCON
LF
LDRED WF
(L3,04,06)
Dimensions(mm)
GAMF DMIN
RE
Maximum
recommendation
l/d
ratio Clamp
Screw
Wrench
FSWUB1008R/L-L3E
a a
L302pp
140
13.8
7.2
14
10
0.2
TS2
TKY06F
FSWUB1008R-L3E-2/3
L302pp
90
13.8
7.2
14
10
0.2
TS2
TKY06F
FSWUB1008R-L3E-1/2
L302pp
70
13.8
7.2
14
10
0.2
TS2
TKY06F
FSWUB1210R/L-L3E
a a
L302pp
10
160
16.0
11
12
0.2
7.5
TS2
TKY06F
FSWUB1210R-L3E-2/3
L302pp
10
105
16.0
11
12
0.2
7.5
TS2
TKY06F
FSWUB1210R-L3E-1/2
L302pp
10
80
16.0
11
12
0.2
7.5
TS2
TKY06F
FSWUP 1412R/L-04E
a a
0402pp
12
180
17.8
11
14
0.4
TS253 TKY08F
FSWUP 1412R-04E-2/3
0402pp
12
120
17.8
11
14
0.4
TS253 TKY08F
FSWUP 1412R-04E-1/2
0402pp
12
90
17.8
11
14
0.4
TS253 TKY08F
FSWUP 1816R/L-04E
a a
0402pp
16
220
21.8
15
18
0.4
TS253 TKY08F
FSWUP 1816R-04E-2/3
0402pp
16
145
21.8
15
18
0.4
TS253 TKY08F
FSWUP 1816R-04E-1/2
0402pp
16
110
21.8
15
18
0.4
TS253 TKY08F
FSWUP 2220R/L-06E
a a
0603pp
20
250
24.0
11
19
22
0.8
TS4
TKY15F
FSWUP 2220R-06E-2/3
0603pp
20
165
24.0
11
19
22
0.8
TS4
TKY15F
FSWUP 2220R-06E-1/2
0603pp
20
125
24.0
11
19
22
0.8
TS4
TKY15F
WBMT
WBGT
WPMT
WPGT

WBpp type inserts
a
E010
WPpp type inserts

PCD inserts
A155
A157
B065
FSVUB/C
VCooinserts, VBooinserts
Finish
FP
Finish
Light
FM
LP
Light
LM
93
RE
DMIN
LDRED
(11,16)
(11,16)
(11,16)
Medium
Medium
CBN
H
MP
DCON
LF
(11,16)
Medium

Stock
Insert Number
R L
FSVUC1612R/L-08S
a a
FSVUB2016R/L-11S
a a
FSVUB2520R/L-11S
a a
FSVUB3425R/L-16S
a a
FSVUB4032R/L-16S
a a
(16)
Dimensions(mm)
1103pp
VBET
VBGT 1103pp
VBMT 1604pp
NP-VBGW
1604pp
(16)
(16)
8 16 0.4
TS202 TKY06F
8 20 0.4
TS255 TKY08F
7 25 0.4
TS255 TKY08F
20.5 8.5 23.4 13 34 0.8
SPSVN32 BCP141 TS35D TKY15F
11
H GAMF DMIN RE
5.5 11
16 180 32.5 15.5 8

20 200 40.5 17.5 8
25 220 50
(16)
Shim
DCON LF LDRED WF F2
VCGT
pp 12 150 25
VCMT 0802
Standard
Maximum recommendation
l/d ratio
Order Number
MM
32 250 84.0 27.5 12
15
19
30.4
9 40 0.8
Shim Pin Clamp

Screw Wrench
BORING
GAMF
F2
WF
93
* Clamp Torque (N m) : TS202=0.6, TS255=1.0, TS35D=3.5
FSVPB/C
Finish
FP
Finish
Light
FM
LP
Light
LM
GAMF
DMIN
RE
F2
117
30
WF
11730
LDRED
H
DCON
LF
(11,16)
(11,16)
(11,16)
(11,16)
Medium
Medium
Medium
CBN
MP
MM
Standard
Order Number
Stock
Dimensions(mm)
Insert Number
R L
DCON LF LDRED WF F2
VCGT
VCMT 0802pp 10 150 25
FSVPC1610R/L-08S
a a
FSVPB2012R/L-11S
a a
1103pp 12 150 28 10
FSVPB2516R/L-11S
a a
1103pp
FSVPB3020R/L-11S
a a
FSVPB3425R/L-16S
a a
FSVPB4032R/L-16S
a a
(16)
(16)
(16)
*
Shim
Shim Pin Clamp

Screw Wrench
8 16 0.4 3.5
TS202 TKY06F
8 20 0.4 4
TS255 TKY08F
15
5 25 0.4 5
TS255 TKY08F
19
5 30 0.4 5
TS255 TKY08F
4.5 11
16 180 35 12.5 5
VBET
VBGT
1103pp 20 200 40 15 5
VBMT
NP-VBGW 1604pp 25 220 50 17 5
1604pp 32 250 55 22
H GAMF DMIN RE
(16)
Maximum recommendation
l/d ratio
23.4 13 34 0.8 5
6.5 30.4
9 40 0.8 5

* Clamp Torque (N m) : TS202=0.6, TS255=1.0, TS35D=3.5
VBpp type inserts

VCpp type inserts
CBN & PCD inserts
A148 A150
A151, A152
B048, B064
CUTTING CONDITIONS
SPARE PARTS
TECHNICAL DATA
E012
P001
Q001
E011
BORING BARS
DIMPLE BAR
FSVJB/C
142

a l/d is 3 to 5 times the diameter.
Finish
Light
FM
LP
Light
LM
WF
142
GAMF RE
DMIN
5
LDRED
H
DCON
LF
(11)
Medium
Insert Number
R L
DCON
LF
LDRED WF
(11)
(11)
MV
(08,11)
(08,11)
Dimensions(mm)
Stock
Order Number
(11)
Finish
FV
BORING
Finish
FP
GAMF DMIN
RE
Maximum
recommendation
l/d
ratio Clamp
Screw
FSVJC1612R/L-08S
a a
FSVJC2016R/L-08S
a a
FSVJB2520R/L-11S
a a
FSVJB3025R/L-11S
a a
Wrench
VCGT
VCMT
0802pp
12
150
26
11
16
0.4
TS202 TKY06F
0802pp
16
180
36
15
20
0.4
TS202 TKY06F
VBET
VBGT
VBMT
1103pp
20
200
37.5
19
25
0.4
TS255 TKY08F
1103pp
25
250
45
3.5
23.4
30
0.4
TS255 TKY08F

Work Material
P
Mild Steel
Cutting
Mode
RecomBreaker
mendation
Finish
FV
Light
SV
< 180HB
Medium
Finish
Carbon Steel
Alloy Steel
MV
FV
Light
SV
Medium
MV
Finish
FV
180350HB
M
Stainless Steel
Light
SV
< 200HB
Gray Cast Iron

Tensile Strength
< 350MPa
Aluminium Alloy
H Heat Treated Steel 3565HRC
Grade
Cutting Speed
(m/min)
NX2525
l/d
l/d
<
<
3 (Steel shank)
6 (Carbide shank)
l/d = 4 5 (Steel shank)

l/d = 7 8 (Carbide shank)
Feed
(mm/rev)
Depth of Cut
(mm)
Feed
(mm/rev)
Depth of Cut
(mm)
170 (120 220)
0.10 (0.05 0.15)
0.5
0.10 (0.05 0.15)
0.5
1.0
NX3035
150 (100 200)
0.20 (0.10 0.25)
1.0
0.15 (0.05 0.20)
NX2525
160 (110 210)
0.20 (0.10 0.25)
1.0
0.15 (0.05 0.20)
1.0
NX3035
140 (90 190)
0.25 (0.15 0.35)
2.0
0.20 (0.15 0.25)
1.5
NX2525
150 (100 200)
0.25 (0.15 0.35)
2.0
0.20 (0.15 0.25)
1.5
VP15TF
140 (90 190)
0.10 (0.05 0.15)
0.5
0.10 (0.05 0.15)
0.5
NX2525
130 (80 180)
0.10 (0.05 0.15)
0.5
0.10 (0.05 0.15)
0.5
UE6020
140 (90 190)
0.20 (0.10 0.25)
1.0
0.15 (0.05 0.20)
1.0
NX3035
110 (60 160)
0.20 (0.10 0.25)
1.0
0.15 (0.05 0.20)
1.0
UE6020
130 (80 180)
0.25 (0.15 0.35)
2.0
0.20 (0.15 0.25)
1.5
NX3035
100 (60 150)
0.25 (0.15 0.35)
2.0
0.20 (0.15 0.25)
1.5
VP15TF
150 (110 190)
0.10 (0.05 0.15)
0.5
0.10 (0.05 0.15)
0.5
US735
125 (85 165)
0.20 (0.10 0.25)
1.0
0.15 (0.05 0.20)
1.0
VP15TF
130 (90 170)
0.20 (0.10 0.25)
1.0
0.15 (0.05 0.20)
1.0
US735
105 (70 135)
0.20 (0.15 0.25)
2.0
0.20 (0.15 0.25)
1.0
VP15TF
120 (80 160)
0.20 (0.15 0.25)
2.0
0.20 (0.15 0.25)
1.0
0.5
Medium
MV
Finish
F, FS
HTi10
130 (90 160)
0.15 (0.10 0.20)
0.5
0.15 (0.10 0.20)
Medium
MV
VP15TF
90 (60 120)
0.20 (0.15 0.25)
2.0
0.20 (0.15 0.25)
1.5
F, FS
HTi10
300 (200 400)
0.10 (0.05 0.15)
0.5
0.10 (0.05 0.15)
0.5
Flat Top
MD220
200 (150 250)
0.10 (0.05 0.15)
2.0
0.10 (0.05 0.15)
1.0
Flat Top
MB825
100 (80 200)
0.10 (0.05 0.15)
0.15
0.10 (0.05 0.15)
0.1
Finish
Finish
(Note 1) When vibrations occur, reduce cutting speed by 30%.

(Note 2) The depth of cut needs to be less than the corner diameter when using the FSVJ type.
VBpp type inserts
a
E012
VCpp type inserts

CBN & PCD inserts
A148 A150
A151, A152
B048, B064
DIMPLE BAR
DCLN
a Economical negative insert.

a Single action type.
a Excellent vibration resistance due to a light dimple head. (With coolant hole.)
CNooinserts
With coolant hole
Finish
FH
GAMF
WF
IN
DM
95
95
RE LDRED
(12)
(12)
(12)
(12)
Medium
Stainless
CBN

Order Number
Insert Number
DCON LF LDRED WF
R L
A25R-DCLNR/L12
a a
A32S-DCLNR/L12
a a
A40T-DCLNR/L12
a a
Standard
MM
(12)
(12)
(12)
CNMA 1204pp 25 200 40

CNMG
1204pp 32 250 50
CNMM
CNGG 1204pp 40 300 63
(12)
Dimensions(mm)
Stock
Medium
MP
DCON
LF
Light
LP
Medium
MH
Light
SA
H GAMF DMIN RE
Shim
Shim Pin
Clamp
Bridge
Clamp
Screw
Spring
Wrench
17
23 11 32 0.8 LLSCP42 LLP14 DCK2613 DCS1 DC0621T TKY20F
22
30 13 40 0.8 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
27
37 10 50 0.8 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
BORING
DOUBLE
CLAMP
DDUN
DNooinserts
With coolant hole
Finish
FH
93
GAMF
WF
IN
DM
93
RE LDRED

Order Number
Stock
R L
A25R-DDUNR/L15
a a
A32S-DDUNR/L15
a a
A40T-DDUNR/L15
a a
(15)
(15)
(15)
(15)
Stainless
G class
CBN
MM
R/L
(15)
(15)
(15)
DCON LF LDRED WF
DNMA 1504pp 25 200 40

DNMG
DNMX 1504pp 32 250 50
DNGA
DNGG 1504pp 40 300 63
(15)
Dimensions(mm)
Insert Number
Medium
MH
DCON
LF
Medium
MP
Medium
Standard
Light
LP
H GAMF DMIN RE
Shim
Shim Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
17
23 13 35 0.8 LLSDP42 LLP14 DCK2613 DCS1 DC0621T TKY20F
22
30 13 40 0.8 LLSDN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
27
37 10 50 0.8 LLSDN42 LLP14 DCK2613 DCS1 DC0621T TKY20F

Work Material
Carbon Steel
Alloy Steel
Stainless Steel
Gray Cast Iron
Hardness
Cutting
Mode
180350HB
< 200HB
Tensile Strength
< 350MPa
l/d < 3
l/d=34
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Medium
110 (80 140)
0.25 (0.1 0.4)
5.0
110 (80 140)
0.2 (0.1 0.3)
4.0
Medium
80 (60 100)
0.2 (0.1 0.3)
4.0
70 (50 100)
0.15 (0.1 0.25)
3.0
Medium
80 (60 100)
0.25 (0.1 0.4)
5.0
80 (60 100)
0.2 (0.1 0.3)
4.0
CNpp type inserts

DNpp type inserts
CBN & PCD inserts
A092 A097
A098 A103
B022 B027, B055
SPARE PARTS
TECHNICAL DATA
P001
Q001
E013
BORING BARS
DOUBLE
CLAMP
DIMPLE BAR
DSKN

a Single action type.
a Excellent vibration resistance due to a light dimple head. (With coolant hole.)
SNooinserts
With coolant hole
Finish
FH
WF
IN
DM
75
75
GAMF
RE LDRED
Stock
(12)
(12)
(12)
Stainless
G class
CBN
BORING
R L
A25R-DSKNR/L12
A32S-DSKNR/L12
SNMA
a a SNMG
SNMM
a a SNGA
SNGG
DCON LF LDRED WF
(12)
R/L
(12)
(12)
(12)
H GAMF DMIN RE
Shim
Shim Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
1204pp 25 200 40
17
23 13 32 0.8 LLSSP42 LLP14 DCK2613 DCS1 DC0621T TKY20F
1204pp
22
30 13 40 0.8 LLSSN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
32 250 50
DTFN
TNooinserts
With coolant hole
Finish
FH
WF
IN
DM 91
91
GAMF
RE LDRED
Stock
Insert Number
LF
A32S-DTFNR/L16
TNMA
a a TNMG
TNMM
a a TNGA
TNGG
DCON LF LDRED WF
Medium
MH
(16)
(16)
(16)
(16)
Medium
Stainless
G class
CBN
MM
R/L
(16)
(16)
(16)
H GAMF DMIN RE
(16)
Dimensions(mm)
R L
A25R-DTFNR/L16
Medium
MP
DCON

Order Number
Light
LP
Standard
MM
Dimensions(mm)
Insert Number
Medium
MH
(12)

Order Number
Medium
MP
Medium
Standard
H
DCON
LF
Light
LP
Shim
Shim Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
1604pp 25 200 40
17
23 13 32 0.8 LLSTP32 LLP23 DCK2211 DCS2 DC0520T TKY15F
1604pp 32 250 50
22
30 13 40 0.8 LLSTN32 LLP23 DCK2211 DCS2 DC0520T TKY15F
SNpp type inserts
a
E014
TNpp type inserts

CBN & PCD inserts
A105 A109
A110 A115
B028 B031, B056
IN
93
GAMF
RE LDRED
(16)
(16)
(16)
(16)
Stainless
G class
CBN
Standard
DCON LF LDRED WF
R L
A40T-DVUNR/L16
MM
R/L
(16)
(16)
(16)
a a VNMA 1604pp 40 300 63

VNGA
H GAMF DMIN RE
27
37
(16)
Dimensions(mm)
Insert Number
Medium
MH
Medium

Stock
Medium
MP
DCON
LF
Order Number
Light
LP
93
WF
DM
Finish
FH
Shim
Shim Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
50 0.8 DCSVN32 LLP13 DCK3113 DCS2 DC0520T TKY15F
DWLN
WNooinserts
With coolant hole
Finish
FH
WF
IN
DM 95
95
GAMF
RE LDRED
(08)
(08)
(06,08)
Medium
Rough
Stainless

Order Number
Stock
RP
R L
DCON LF LDRED WF
(08)
MM
(08)
(08)
(06,08)
Dimensions(mm)
Insert Number
Medium
MH
DCON
LF
Medium
MP
Medium
Standard
Light
LP
H GAMF DMIN RE
Shim
Shim Pin
Clamp
Bridge
Spring
Clamp
Screw
Wrench
A25R-DWLNR/L06
a a
WNMG 0604pp 25 200 40
17
23 13 35 0.8 LLSWP32 LLP23 DCK2211 DCS2 DC0520T TKY15F
A25R-DWLNR/L08
a a
17
23 13 35 0.8 LLSWP42 LLP14 DCK2613 DCS1 DC0621T TKY20F
A32S-DWLNR/L08
a a
22
30 13 40 0.8 LLSWN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
A40T-DWLNR/L08
a a
0804pp 25 200 40
WNMA
0804pp 32 250 50
WNMG
0804pp 40 300 63
27
37 10 50 0.8 LLSWN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
BORING
DVUN
VNooinserts
With coolant hole
Clamp Torque (N m) : DC0520T=3.5, DC0621T=5.0

Work Material
Carbon Steel
Alloy Steel
Stainless Steel
Gray Cast Iron
Hardness
Cutting
Mode
180350HB
< 200HB
Tensile Strength
< 350MPa
l/d < 3
l/d=34
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Medium
110 (80 140)
0.25 (0.1 0.4)
5.0
110 (80 140)
0.2 (0.1 0.3)
4.0
Medium
80 (60 100)
0.2 (0.1 0.3)
4.0
70 (50 100)
0.15 (0.1 0.25)
3.0
Medium
80 (60 100)
0.25 (0.1 0.4)
5.0
80 (60 100)
0.2 (0.1 0.3)
4.0
VNpp type inserts

WNpp type inserts
CBN & PCD inserts
A116 A118
A119 A123
B032 B034, B057
SPARE PARTS
TECHNICAL DATA
P001
Q001
E015
BORING BARS
MICRO-DEX
BORING BARS
SCLC
a The minimum cutting diameter is from

a 7 positive insert, carbide shank type.
a Easy-to-use tool geometries.
a Suitable for small workpieces.
& 5.
a l/d
is 5 times the diameter.
WF
GAMF
DMIN
L-F
(03,04)
DCON
95
95
Finish
CCooinserts
Carbide shank
RE
PCD/CBN
H
LF
Order Number
Stock
Insert Number
DCON
LF
WF
03S1pp
90
2.5
3.7
15
03S1pp
100
3.0
4.7
13
R
BORING
Dimensions(mm)
GAMF DMIN
RE
(03,04)
2
Clamp
Screw
Wrench
0.2
TS16
TKY06F
0.2
TS16
TKY06F
C04GSCLCR03
C05HSCLCR03
C06JSCLCR04
NP-CCMW 04T0pp
110
3.5
5.7
13
0.2
TS21
TKY06F
C07KSCLCR04
04T0pp
125
4.0
6.7
11
0.2
TS21
TKY06F
1
*CCGT
of inscribed circle is special. (For SCLC type)

*12 Diameter
*
SWUB
WF
GAMF
DMIN
L-F
(02,L3)
DCON
93
93
Finish
WBGT inserts
Carbide shank
RE
LF
Order Number
Stock
Insert Number
C06JSWUBR02
C07KSWUBRL3
WBGT
GAMF DMIN
DCON
LF
WF
0201ppL-F
100
3.0
4.7
15
0201ppL-F
110
3.5
5.7
13
L302ppL-F
125
4.0
6.7
15
C05HSWUBR02
Dimensions(mm)
RE
Clamp
Screw
Wrench
0.2
TS21
TKY06F
0.2
TS2C
TKY06F
0.2
TS2
TKY06F
Clamp Torque (N m) : TS21=0.6, TS2C=0.6, TS2=0.6
CCGT type inserts
a
E016
WBGT type inserts

CBN inserts
A127
A155
B040, B041, B059
STUC
RE
0.35
WF
GAMF 27
DMIN
LF

Stock
Insert Number
TCGT
0601pp
DCON
LF
WF
GAMF
DMIN
RE
125
4.0
6.7
12
0.2
Clamp
Screw
Wrench
TS2C
TKY06F
Clamp Torque (N m) : TS2C=0.6
BORING
Dimensions(mm)
C07KSTUCR06
(06)
Depth of cut is limited

when cutting backwards.
Order Number
L-F
DCON
93
93
Finish
TCGT inserts
Carbide shank

Work Material
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
l/d
Carbon Steel, Alloy Steel
NX2525
80 (40120)
0.03 (0.010.05)
0.2 (0.10.3)
35
Stainless Steel
VP15TF
80 (40120)
0.03 (0.010.05)
0.2 (0.10.3)
35
Gray Cast Iron
VP15TF
80 (40120)
0.03 (0.010.05)
0.2 (0.10.3)
35
VP15TF
120 (80160)
0.05 (0.010.08)
0.4 (0.10.6)
35
MD220
120 (80160)
0.05 (0.010.08)
0.4 (0.10.6)
35
MB810
80 (40120)
0.03 (0.010.05)
0.1 (0.030.2)
35
180350HB
< 200HB
< 350MPa
N
Non-Ferrous Meterial
Heat Treated Steel

3565HRC
TCGT type inserts

SPARE PARTS
TECHNICAL DATA
A141
P001
Q001
E017
BORING BARS
MICRO-DEX
BORING BARS
STANDARD HOLDER
5
3-M4 x 0.7
S2
D5
S1
S2
3-M4 x 0.7
D5
S1
DCON
DCB
10
z
S3
20
10
c
LF
Stock
BORING
*22
*2
*2
*
RBH 15840N
RBH 15850N
RBH 15860N
RBH 15870N
RBH 1640N
RBH 1650N
RBH 1660N
RBH 1670N
RBH19040N
RBH19050N
RBH19060N
RBH19070N
RBH 2040N
RBH 2050N
RBH 2060N
RBH 2070N
RBH 2240N
RBH 2250N
RBH 2260N
RBH 2270N
RBH 2540N
RBH 2550N
RBH 2560N
RBH 2570N
RBH 25440N
RBH 25450N
RBH 25460N
RBH 25470N
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Dimensions(mm)
*Clamp Screw
Wrench
Torque
(N m)
HKY20F
HKY20F
2.0
2.0
A
A
HKY20F
HKY20F
2.0
2.0
A
A
A
A
HKY20F
HKY20F
2.0
2.0
A
A
A
A
A
A
HKY20F
HKY20F
2.0
2.0
C04GSpppRpp
C05HSpppRpp
B
B
B
B
B
B
HKY20F
HKY20F
2.0
2.0
C06JSpppRpp
C07KSpppRpp
B
B
B
B
B
B
HKY20F
HKY20F
2.0
2.0
15
15
C04GSpppRpp
C05HSpppRpp
A
A
B
B
B
B
HKY20F
HKY20F
2.0
2.0
15
20
15
20
C06JSpppRpp
C07KSpppRpp
A
A
B
B
B
B
HKY20F
HKY20F
2.0
2.0
125
125
15
15
15
15
12.5 C04GSpppRpp
12.5 C05HSpppRpp
A
A
B
B
B
B
A
A
HKY20F
HKY20F
2.0
2.0
15
16
125
125
15
20
15
20
15
15
C06JSpppRpp
C07KSpppRpp
A
A
B
B
B
B
A
A
HKY20F
HKY20F
2.0
2.0
4
5
13
14
150
150
15
15
15
15
C04GSpppRpp
C05HSpppRpp
A
A
C
C
C
C
HKY20F
HKY20F
2.0
2.0
25
25
6
7
15
16
150
150
15
20
15
20
C06JSpppRpp
C07KSpppRpp
A
A
C
C
C
C
HKY20F
HKY20F
2.0
2.0
25.4
25.4
4
5
13
14
150
150
15
15
15
15
C04GSpppRpp
C05HSpppRpp
A
A
C
C
C
C
HKY20F
HKY20F
2.0
2.0
25.4
25.4
6
7
15
16
150
150
15
20
15
20
C06JSpppRpp
C07KSpppRpp
A
A
C
C
C
C
HKY20F
HKY20F
2.0
2.0
DCON DCB
D5
LF
S1
S2
S3
15.875
15.875
4
5
15
15
100
100
15
15
15
15
15.875
15.875
6
7
15
15
100
100
15
20
15
20
16
16
4
5
15
15
100
100
15
15
16
16
6
7
15
15
100
100
19.05
19.05
4
5
18
18
19.05
19.05
6
7
20
20
MICRO-DEX
C04GSpppRpp
C05HSpppRpp
A
A
A
A
A
A
C06JSpppRpp
C07KSpppRpp
A
A
A
A
15
15
C04GSpppRpp
C05HSpppRpp
A
A
15
20
15
20
C06JSpppRpp
C07KSpppRpp
125
125
15
15
15
15
18
18
125
125
15
20
15
20
4
5
13
14
125
125
15
15
20
20
6
7
15
16
125
125
22
22
4
5
13
14
22
22
6
7
25
25
number of clamp screw A=HSS04004, B=HSS04006, C=HSS04008

*12 Order
Revised order number.
*
Conventional Order
Number
Revised Order
Number
RBH1940N
RBH1950N
RBH1960N
RBH1970N
RBH19040N
RBH19050N
RBH19060N
RBH19070N
E018
RBH158ppN, RBH16ppN,
RBH190ppN
RBH22ppN has a temporary set screw for different machine specifications.

(Represented by number 4)
Order Number
x
LF
: Inventory maintained in Japan. (MICRO-MINI TWIN is available in 1 piece in one pack.)
MICRO-MINI TWIN
CB
For internal machining
DCON
LF
L19
Right hand tool only.
LDRED
Stock
Coated
TF15 VP15TF
Order Number
Micro
Grain
CB02RS
CB02RS-B
CB02RS-01
CB02RS-01B
CB02RS-02
CB02RS-02B
CB03RS
CB03RS-B
CB03RS-01
CB03RS-01B
CB03RS-02
CB03RS-02B
CB04RS
CB04RS-B
CB04RS-01
CB04RS-01B
CB04RS-02
CB04RS-02B
CB05RS
CB05RS-B
CB05RS-02
CB05RS-02B
CB06RS
CB06RS-B
CB06RS-02
CB06RS-02B
CB07RS
CB07RS-B
CB07RS-02
CB07RS-02B
CB08RS
CB08RS-B
CB08RS-02
CB08RS-02B
with
without
with
without
with
without
with
without
with
without
with
without
with
without
with
without
with
without
with
Breaker
without
with
without
with
without
with
without
with
without
with
without
with
without
with
without
Dimensions(mm)
DMIN 1
l/d < 3 l/d>3
2.2
3.6
2.2
3.9
2.2
3.6
2.2
4.2
2.2
3.6
2.2
4.9
3.2
4.2
3.2
4.4
3.2
4.2
3.2
4.5
3.2
4.2
3.2
4.8
4.2
5.1
4.2
5.2
4.2
5.1
4.2
5.3
4.2
5.1
4.2
5.5
5.2
6.0
5.2
6.1
5.2
6.0
5.2
6.4
6.2
7.2
6.2
7.3
6.2
7.2
6.2
7.8
7.2
8.6
7.2
8.8
7.2
8.6
7.2
9.2
8.2
9.5
8.2
9.6
8.2
9.5
8.2
9.8
RE
DCON
LF
L19
LDRED
WF
F2
0.05
0.05
0.1
0.1
0.2
0.2
0.05
0.05
0.1
0.1
0.2
0.2
0.05
0.05
0.1
0.1
0.2
0.2
0.05
0.05
0.2
0.2
0.05
0.05
0.2
0.2
0.05
0.05
0.2
0.2
0.05
0.05
0.2
0.2
2
2
2
2
2
2
3
3
3
3
3
3
4
4
4
4
4
4
5
5
5
5
6
6
6
6
7
7
7
7
8
8
8
8
50
50
50
50
50
50
50
50
50
50
50
50
60
60
60
60
60
60
70
70
70
70
75
75
75
75
85
85
85
85
95
95
95
95
5
5
5
5
5
5
7.5
7.5
7.5
7.5
7.5
7.5
10
10
10
10
10
10
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
15
15
15
15
6
6
6
6
6
6
9
9
9
9
9
9
12
12
12
12
12
12
15
15
15
15
18
18
18
18
21
21
21
21
24
24
24
24
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2.5
2.5
2.5
2.5
3
3
3
3
3.5
3.5
3.5
3.5
4
4
4
4
0.25
0.25
0.25
0.25
0.25
0.25
0.35
0.35
0.35
0.35
0.35
0.35
0.45
0.45
0.45
0.45
0.45
0.45
0.55
0.55
0.55
0.55
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.85
0.85
0.85
0.85
1.8
1.8
1.8
1.8
1.8
1.8
2.7
2.7
2.7
2.7
2.7
2.7
3.6
3.6
3.6
3.6
3.6
3.6
4.5
4.5
4.5
4.5
5.4
5.4
5.4
5.4
6.3
6.3
6.3
6.3
7.2
7.2
7.2
7.2
1.4
1.4
1.4
1.4
1.4
1.4
2.3
2.3
2.3
2.3
2.3
2.3
3.1
3.1
3.1
3.1
3.1
3.1
3.9
3.9
3.9
3.9
4.7
4.7
4.7
4.7
5.5
5.5
5.5
5.5
6.3
6.3
6.3
6.3
BORING
* RE0.015
2
F2
WF
DMIN : Min. Cutting Diameter

*12 The
RE dimension represents the size before grinding a chip breaker.
*

Work Material
Cutting Speed
(m/min)
Micro-Mini Twin CB
Feed
Depth of Cut
(mm/rev)
(mm)
l/d
Micro-Mini Twin CR
Feed(mm/rev)
Cutting Speed
03RS/04RS
05RS
(m/min)
80
(40 120)
0.03
(0.01 0.05)
0.2
(0.1 0.3)
35
80
(40 120)
0.02
(0.01 0.03)
0.03
(0.01 0.05)
Stainless Steel
80
(40 120)
0.03
(0.01 0.05)
0.2
(0.1 0.3)
35
80
(40 120)
0.02
(0.01 0.03)
0.03
(0.01 0.05)
Gray Cast Iron
80
(40 120)
0.03
(0.01 0.05)
0.2
(0.1 0.3)
35
80
(40 120)
0.03
(0.01 0.05)
0.03
(0.01 0.05)
120
(80 160)
0.05
(0.01 0.08)
0.3
(0.1 0.5)
35
120
(80 160)
0.03
(0.01 0.05)
0.05
(0.01 0.08)
180350HB
< 200HB
< 350MPa
(Note) Recommend wet machining.
TECHNICAL DATA
Q001
E019
BORING BARS
MICRO-MINI TWIN
CR
For internal copying

WF
52
DMIN
RE
LU
H
LF
DCON
L19

Order Number
Stock
Micro
Coated
Grain
TF15 VP15TF
BORING
CR03RS-01
CR03RS-01B
CR04RS-01
CR04RS-01B
CR05RS-01
CR05RS-01B
Dimensions(mm)
Breaker
without
with
without
with
without
with
DMIN
RE
DCON
LF
LU
L19
WF
3.5
3.5
4.5
4.5
5.5
5.5
0.1
0.1
0.1
0.1
0.1
0.1
3
3
4
4
5
5
50
50
60
60
70
70
8
8
10
10
12
12
6
6
7
7
8
8
0.15
0.15
0.15
0.15
0.15
0.15
2.7
2.7
3.6
3.6
4.5
4.5

Work Material
Cutting Speed
(m/min)
Micro-Mini Twin CB
Feed
Depth of Cut
(mm/rev)
(mm)
l/d
Micro-Mini Twin CR
Feed(mm/rev)
Cutting Speed
03RS/04RS
05RS
(m/min)
80
(40 120)
0.03
(0.01 0.05)
0.2
(0.1 0.3)
35
80
(40 120)
0.02
(0.01 0.03)
0.03
(0.01 0.05)
Stainless Steel
80
(40 120)
0.03
(0.01 0.05)
0.2
(0.1 0.3)
35
80
(40 120)
0.02
(0.01 0.03)
0.03
(0.01 0.05)
Gray Cast Iron
80
(40 120)
0.03
(0.01 0.05)
0.2
(0.1 0.3)
35
80
(40 120)
0.03
(0.01 0.05)
0.03
(0.01 0.05)
120
(80 160)
0.05
(0.01 0.08)
0.3
(0.1 0.5)
35
120
(80 160)
0.03
(0.01 0.05)
0.05
(0.01 0.08)
180350HB
< 200HB
< 350MPa
(Note 1) Recommend wet machining.

(Note 2) The recommended tool overhang of CR type is LU+2mm.
E020
y PRECAUTIONS WHEN USING THE MICRO-MINI TWIN

aWhen using a holder for general purpose / small automatic lathe:
aTo avoid chipping of the 2nd cutting edge take care when inserting the boring bar into the holder.
Refer to fig.1. If the 2nd edge contacts the internal face of the holder there is a possibility that it
may chip.
Fig.1
Internal face of the holder
Cutting edge
Insert direction
eWhen using Mitsubishi holders
When using holders with a tool overhang of recommended quantity, ensure that the 3rd clamping
screw is removed prior to machining. (RBH1620N, RBH19020N, RBH2020N and RBH2520N do
not have the 3rd screw.) The set torque value for clamping screw is 2.0 Nm.
Fig.2
3rd clamping screw

1
2nd cutting edge
Insert point
BORING
sWhen using this type of holder, there is a possibility that damage to the shank and the 2nd cutting
edge can occur. Make sure that the clamping screws are tightened to the set torque value.
Additionally make sure that there is no clamping screw near the 2nd cutting edge as this can
break the boring bar.
aWhen using a square type holder:
aWhen installing the boring bar into the holder, tighten the clamp screws after ensuring the flats on
the tool holder are parallel to the reference flats on the micro-mini bar. Refer to fig.3.
sMake sure that the clamping screws are tightened to the recommended values.
dDo not tighten the clamp screw without a bar in place, otherwise the bridge will be deformed.
Fig.3
Insert
The reference plane

of square type holder
Tighten the clamping screw ensuring making

the micro-mini twin boring bars is in contact
with the reference plane of square type holder.
MACHINING METHODS OF THE CR TYPE

a Profile turning
By drilling a pre-prepared hole, the
machining time will be shortened
and chip control will be improved.
Machining a work piece

without a pre-prepared hole with a pre-prepared hole
R5
Workpiece
Holder
Cutting Speed
Feed
Depth of Cut
Wet Cutting
: JIS S20C
: CR05RS-01B
: 80m/min
: 0.05mm/rev
: 0.05mm
a Inner end facing

By drilling a pre-prepared hole, the
machining time will be shortened
and chip control will be improved.
R5
Depth of Cut
The cutting edge

should not be
cross the centre
line of the
work piece.
If the cutting edge crosses the centre line of a

work piece, the cutting edge can fracture.

without a pre-prepared hole with a pre-prepared hole
Copying
The depth of cut
should be smaller
than the corner
radius value.
: JIS S20C
: CR05RS-01B
: 80m/min
: 0.05mm/rev
: 0.05mm
FOR USE
Profile turning,
Inner end facing
Depth of Cut
3
Workpiece
Holder
Cutting Speed
Feed
Depth of Cut
Wet Cutting
y NOTES
Depth of Cut
Depth of Cut
Depth of Cut
2
With depths of cut larger than the

corner radius value, burrs will be formed.
TECHNICAL DATA
Q001
E021
BORING BARS
MICRO-MINI
BORING BARS
a Solid carbide type with minimum cutting diameter & 3.2mm.

a l/d is 5 times the diameter.
a Cutting edge can be shaped according to the application thus,
it covers a wide application range (threading, grooving, copying, etc).
STANDARD MICRO-MINI BORING BARS (Solid carbide boring bar)

Dimensions(mm)
Order Number
Stock
Geometry
CW
DCON
LF
2.0
80
LDRED DMIN
F2
BORING
15
3.2
1.0
C04FR-BLS
2.5
80
20
4.2
1.5
C05HR-BLS
3.0
100
25
5.2
2.0
F2
Flat area
Flat area
CW
LDRED
DMIN
C03FR-BLS
DCON
TF15
LF

Cutting Speed
(m/min)
Work Material
Feed
(mm/rev)
Depth of Cut
(mm)
l/d
40 (3050)
0.05 ( 0.1)
0.2 (0.10.3)
Stainless Steel
40 (3050)
0.05 ( 0.1)
0.2 (0.10.3)
Gray Cast Iron
40 (3050)
0.05 ( 0.05)
80 (60100)
0.05 ( 0.1)
180350HB
< 200HB
< 350MPa
Edge Condition (mm)

Corner Radius or C
Honing
0.10.5
0.010.05
<0.4
(Honing not required)
0.2 (0.10.3)
0.10.5
0.010.05
0.3 (0.10.5)
0.10.5
(Honing not required)
<0.03
<0.03
*Cutting edge is not honed. Please hone according to the workpiece before machining.
y GRINDING THE CUTTING EDGE OF MICRO-MINI BORING BAR
a MICRO-MINI boring bar can be applied to boring and grooving without any modifications. It can also be reground as shown below.
a For shaping and regrinding, use a diamond whetstone approximately #250 #400.
Please grind according to the application using the figure below as a reference.
Grooving
12
12
(Grinding)
Grinding Examples
Application
Boring
25
20
0. 5 0.8
0.3 0.5Corner radius
E022
Groove width
25
Grinding
0.5 0.8
Thread angle
Grinding
35
20
4 CW
Grinding
Grinding
60
(Grinding)
Threading
6 Double sided relief
: Inventory maintained in Japan. (MICRO MINI is available in 1 piece in one pack.)
19
19
3-M4 x 0.7
S2
10
LF
Order Number
*2
*2
*2
*2
*2
*
2
RBH15820N
RBH15830N
RBH15840N
RBH15850N
RBH15860N
RBH15870N
RBH15880N
RBH1620N
RBH1630N
RBH1640N
RBH1650N
RBH1660N
RBH1670N
RBH1680N
RBH19020N
RBH19030N
RBH19040N
RBH19050N
RBH19060N
RBH19070N
RBH19080N
RBH2020N
RBH2030N
RBH2040N
RBH2050N
RBH2060N
RBH2070N
RBH2080N
RBH2220N
RBH2230N
RBH2240N
RBH2250N
RBH2260N
RBH2270N
RBH2280N
RBH2520N
RBH2530N
RBH2540N
RBH2550N
RBH2560N
RBH2570N
RBH2580N
RBH25420N
RBH25430N
RBH25440N
RBH25450N
RBH25460N
RBH25470N
RBH25480N
Stock
RBH158ppN, RBH16ppN, RBH190ppN
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
S1
S2
10
20
LF
DCON DCB D5
LF
S1
S2
S3
Micro-Mini
C
15.875
15.875
15.875
15.875
15.875
15.875
15.875
2
3
4
5
6
7
8
15
15
15
15
15
15
15
100
100
100
100
100
100
100
10
10
15
15
15
20
20
10
15
15
15
20
20
03FR-BLS
04FR-BLS
05HR-BLS
16
16
16
16
16
16
16
2
3
4
5
6
7
8
15
15
15
15
15
15
15
100
100
100
100
100
100
100
10
10
15
15
15
20
20
10
15
15
15
20
20
03FR-BLS
04FR-BLS
05HR-BLS
19.05
19.05
19.05
19.05
19.05
19.05
19.05
2
3
4
5
6
7
8
18
18
18
18
18
18
18
125
125
125
125
125
125
125
10
10
15
15
15
20
20
10
15
15
15
20
20
03FR-BLS
04FR-BLS
05HR-BLS
20
20
20
20
20
20
20
2
3
4
5
6
7
8
11
12
13
14
15
16
17
125
125
125
125
125
125
125
10
10
15
15
15
20
20
10
15
15
15
20
20
03FR-BLS
04FR-BLS
05HR-BLS
22
22
22
22
22
22
22
2
3
4
5
6
7
8
11
12
13
14
15
16
17
125
125
125
125
125
125
125
10
10
15
15
15
20
20
10
15
15
15
20
20
25
25
25
25
25
25
25
2
3
4
5
6
7
8
11
12
13
14
15
16
17
150
150
150
150
150
150
150
10
10
15
15
15
20
20
10
15
15
15
20
20
03FR-BLS
04FR-BLS
05HR-BLS
25.4
25.4
25.4
25.4
25.4
25.4
25.4
2
3
4
5
6
7
8
11
12
13
14
15
16
17
150
150
150
150
150
150
150
10
10
15
15
15
20
20
10
15
15
15
20
20
03FR-BLS
04FR-BLS
05HR-BLS
RBH19020N
RBH19030N
RBH19040N
S2
S1
10
S3
20
c
LF
RBH22ppN
10
10 03FR-BLS
12.5 04FR-BLS
12.5 05HR-BLS
15
15
15
Micro-Mini Twin
CB
CR
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
08RS(-B)
08RS-0p(B)
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
08RS(-B)
08RS-0p(B)
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
08RS(-B)
08RS-0p(B)
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
08RS(-B)
08RS-0p(B)
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
08RS(-B)
08RS-0p(B)
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
08RS(-B)
08RS-0p(B)
02RS(-B)
02RS-0p(B)
03RS(-B)
03RS-0p(B)
04RS(-B)
04RS-0p(B)
05RS(-B)
05RS-0p(B)
06RS(-B)
06RS-0p(B)
07RS(-B)
07RS-0p(B)
08RS(-B)
08RS-0p(B)
03RS-01(B)
04RS-01(B)
05RS-01(B)
1 Order number of clamp screw A=HSS04004, B=HSS04006, C=HSS04008, D=HSS04003
RBH1920N
RBH1930N
RBH1940N
RBH20ppN, RBH25ppN, RBH254ppN
Dimensions(mm)
Conventional Order Number Revised Order Number
3-M4 x 0.7
D5
D5
DCON
S1
3-M4 x 0.7
D5
DCB
*1 Clamp Screw
zxcv
Torque
Wrench (
N m)
B
A
A
A
A
A
D
B
A
A
A
A
A
D
A
A
A
A
A
D
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
2.0
2.0
2.0
2.0
2.0
2.0
2.0
B
A
A
A
A
A
D
B
A
A
A
A
A
D
A
A
A
A
A
D
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
2.0
2.0
2.0
2.0
2.0
2.0
2.0
C
B
B
B
B
B
A
C
B
B
B
B
B
A
B
B
B
B
B
A
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
2.0
2.0
2.0
2.0
2.0
2.0
2.0
03RS-01(B)
04RS-01(B)
05RS-01(B)
A
A
A
A
A
A
A
A
A
B
B
B
B
A
B
B
B
B
B
A
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
2.0
2.0
2.0
2.0
2.0
2.0
2.0
03RS-01(B)
04RS-01(B)
05RS-01(B)
A
A
A
A
A
A
A
B
B
B
B
B
B
B
C
B
B
B
B
B
A
A
A
A
A
A
A
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
2.0
2.0
2.0
2.0
2.0
2.0
2.0
A
A
A
A
A
A
A
B
B
C
C
C
C
B
C
C
C
C
C
B
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
2.0
2.0
2.0
2.0
2.0
2.0
2.0
A
A
A
A
A
A
A
B
B
C
C
C
C
B
C
C
C
C
C
B
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
HKY20F
2.0
2.0
2.0
2.0
2.0
2.0
2.0
03RS-01(B)
04RS-01(B)
05RS-01(B)
03RS-01(B)
04RS-01(B)
05RS-01(B)
03RS-01(B)
04RS-01(B)
05RS-01(B)
03RS-01(B)
04RS-01(B)
05RS-01(B)
BORING
y ROUND TYPE HOLDER
*2 Revised order number.
RBH1950N
RBH1960N
RBH1970N
RBH19050N
RBH19060N
RBH19070N
SPARE PARTS
TECHNICAL DATA
P001
Q001
E023
BORING BARS
MICRO-MINI TWIN
y SQUARE TYPE HOLDER
CB type (Boring bar fits to a holder)
CR type (Boring bar fits to a holder)

8
WF
10
100
Stock
10
BORING
L24
(Clamp)
WF
20
L24
Order Number
10
45
Dimensions(mm)
WF
L24
Micro-Mini Twin
CB
CR
CB
CR
624 (610)
CB
CR
Clamp
Screw
CB
CR
12.9
02RS(-B)
02RS-0 p(B)
HSC04010 HKY30R
4.8
1119.5 (12)
13.8
03RS(-B)
03RS-01(B) HSC05012 HKY40R
03RS-0 p(B)
9.5
1129.5 (1220) 1327.5 (14)
14.7
04RS(-B)
04RS-01(B) HSC05012 HKY40R
04RS-0 p(B)
9.5
1535.5 (16)
15.6
05RS(-B)
05RS-01(B) HSC05012 HKY40R
05RS-0 p(B)
9.5
SBH1020R
13
SBH1030R
14
12.65
SBH1040R
15
13.15
SBH1050R
16
13.65 13.537 (1525)
SBH1060R
17
13.542 (1830)
16.5
06RS(-B)
06RS-0 p(B)
HSC05012 HKY40R
9.5
SBH1070R
18
13.552 (2135)
17.4
07RS(-B)
07RS-0 p(B)
HSC05012 HKY40R
9.5
8.522 (915)
(Note) The MICRO-DEX and the MICRO-MINI cannot be fit to square holders.
L24 is the length of overhang for sufficient clamping, and ( ) is the recommended length for machining of carbon and alloy steel.
E024
Torque
Wrench (
N m)
a The minimum cutting diameter is from & 10.

a 11positive insert.
a Screw-on type.
a l/d is 3 to 5 times the diameter (up to 7 times
FSTU1
with the carbide shank).
DMIN
WF
TPooinserts
93
RE
LDRED
H
DCON
LF
a a
FSTU110R/L
a a
FSTU112R/L
a a
FSTU116R/L
a a
(08,09,11)
PCD
CBN/PCD
(08,09,11)
Insert Number
TPGX
TPMX
NP-TPGX
NP-TPMX
LDRED WF
(11)
Dimensions(mm)
DCON
LF
0802pp
125
18
15
10
0902pp
10
150
22
13
0902pp
12
180
25
11
1103pp
16
200
30
11
14
R L
FSTU108R/L
(08,09,11)
R/L-F

Stock
Flat Top
GAMF
5
Order Number
Light
R/L
GAMF DMIN
RE
Clamp Screw
Wrench
0.4
CS200T
TKY06F
12
0.4
CS250T
TKY08F
10
16
0.4
CS250T
TKY08F
22
0.4
CS300890T
TKY08F
BORING
TYPE
BORING BARS
* Clamp Torque (N m) : CS200T=0.6, CS250T=1.0, CS300890T=1.0
FSTU2
TPooinserts
Carbide shank
Light
Flat Top
R/L
WF
DMIN
93
RE
LDRED
(08,09,11)
PCD
CBN/PCD
R/L-F
DCON
LF
GAMF
(08,09,11)

Order Number
Stock
Insert Number
a a
FSTU210R/L
a a
FSTU212R/L
a a
FSTU216R/L
a a
TPGX
TPMX
NP-TPGX
NP-TPMX
LDRED WF
(11)
DCON
LF
0802pp
125
13
15
10
0902pp
10
150
16
13
0902pp
12
180
19
11
1103pp
16
200
26
11
14
R L
FSTU208R/L
(08,09,11)
Dimensions(mm)
GAMF DMIN
RE
Clamp Screw
Wrench
0.4
CS200T
TKY06F
12
0.4
CS250T
TKY08F
10
16
0.4
CS250T
TKY08F
22
0.4
CS300890T
TKY08F
Clamp Torque (N m) : CS200T=0.6, CS250T=1.0, CS300890T=1.0

Steel Shank
Carbide Shank
Work Material
P
M
N
Hardness
Carbon Steel
Alloy Steel
180350HB
Stainless Steel
< 200HB
Aluminium Alloy
l/d=34 (Shank Diameter > 25mm)
l/d < 3
l/d < 5
Cutting
Mode
Cutting Speed
(m/min)
Feed
(mm/rev)
l/d=67
Depth of Cut
(mm)
Cutting Speed
(m/min)
Feed
(mm/rev)
Light Cutting
130 (90 160)
0.1 (0.05 0.15)
0.2
120 (80 150)
0.1 (0.05 0.15)
Medium Cutting
90 (60 120)
0.25 (0.15 0.35)
3.0
80 (50 110)
0.15 (0.1 0.2)
Light Cutting
140 (100 180)
0.1 (0.05 0.15)
0.2
140 (100 180)
0.1 (0.05 0.15)
0.2 (0.15 0.25)
2.0
60 (40 80)
0.15 (0.1 0.2)
Medium Cutting
70 (50 90)
Depth of Cut
(mm)
0.2
1.5
0.2
1.0
Light Cutting
300 (200 400)
0.1 (0.05 0.15)
0.2
300 (200 400)
0.1 (0.05 0.15)
0.2
Medium Cutting
200 (150 250)
0.1 (0.05 0.15)
2.0
200 (150 250)
0.1 (0.05 0.15)
1.5
(Note 2) When using insert with right and left hand chip breaker, please use left hand insert
for right hand holder and right hand insert for left hand holder.
TPpp type inserts
A146, A147
CBN & PCD inserts
B046, B047, B062
SPARE PARTS
P 001
TECHNICAL DATA
Q001
E025
BORING BARS
TYPE
BORING BARS

a Clamp-on type.
FCTU1
TPooinserts
M Class
G class
R/L
DMIN
3
WF
93
M Class
LDRED
RE
(11,16)
(11,16)
G class
CBN/PCD
(11,16)
(11,16)
(11,16)
DCON
LF
GAMF
5

Order Number
Stock
Insert Number
DCON LF LDRED WF
BORING
R L
FCTU116R/L
a a
FCTU120R/L
FCTU125R/L
a a
(4 Side Flat Shank)
FCTU132R/L
(4 Side Flat Shank)
a a
Dimensions(mm)
TPMN
TPMR
TPGN
TPGR
a a
GAMF DMIN RE
1103pp
16
200
30
11
14
22
0.4
1603pp
20
200
37
13
18
26
0.8
1603pp
25
250
40
16
22
1603pp
32
300
45
20
29
Breaker Wrench
Shim Shim Pin Clamp
Set
Piece
C3
CBT2N HKY25R
C4
CBT3F HKY30R
32
0.8
PT32 BCP202
C4
CBT3F HKY30R
40
0.8 PT32 BCP201
C4
CBT3F HKY30R
* Clamp Torque (N m) : C3=2.2, C4=3.3
FCTU2
TPooinserts
Carbide shank
M Class
G class
R/L
DMIN
3
WF
93
M Class
RE
LDRED
(11,16)
(11,16)
G class
CBN/PCD
(11,16)
(11,16)
(11,16)
DCON
LF
GAMF
5

Order Number
Stock
Insert Number
FCTU216R
FCTU220R
FCTU225R
Dimensions(mm)
TPMN
TPMR
TPGN
TPGR
DCON LF LDRED WF
GAMF DMIN RE
Breaker Wrench
Shim Shim Pin Clamp
Set
Piece
1103pp
16
200
26
11
14
22
0.4
C3
CBT2N HKY25R
1603pp
20
200
33
13
18
26
0.8
C4
CBT3F HKY30R
1603pp
25
250
37
16
22
32
0.8 PT32 BCP202
C4
CBT3F HKY30R
Clamp Torque (N m) : C3=2.2, C4=3.3
a
E026
TPpp type inserts

CBN & PCD inserts
A162
B052, B068
TYPE
BORING BARS
a The minimum cutting diameter is from & 5.8.

a 7positive insert.
a Screw-on type.
FSWL1
WCooinserts
LDRED
DMIN
Light
Light
R/L
95
WF
(02,L3,04,06)
95
RE
DCON
LF
(02,L3)
PCD
GAMF
Order Number
FSWL108R/LS
108R/LM
(L3,04,06)
Dimensions(mm)
Stock
Insert Number
DCON
LF
0201pp
100
19
2.9
17
5.8
R L
WCMT
WCGT
LDRED WF
GAMF DMIN
RE
Clamp Screw
Wrench
0.4
TS21
TKY06F
FSWL108R/LS
a a
FSWL108R/LM
a a
L302pp
100
25
15
0.4
TS2
TKY06F
FSWL108R/L
a a
0402pp
125
10
15
10
0.4
TS25
TKY08F
FSWL110R/L
a a
0402pp
10
150
12
13
12
0.4
TS25
TKY08F
FSWL112R/L
a a
06T3pp
12
180
15
11
13
16
0.8
TS4
TKY15F
FSWL116R/L
a a
06T3pp
16
200
20
11
14
22
0.8
TS4
TKY15F
WCMT
WCGT
WCMW
WCMT
WCMW
BORING
LDRED
* Clamp Torque (N m) : TS21=0.6, TS2=0.6, TS25=1.0, TS4=3.5
FSWL2
WCooinserts
Carbide shank
Light
R/L
LDRED
DMIN
Light
95
WF
(02,L3,04,06)
95
RE
(02,L3)
PCD
LF
DCON
GAMF
LDRED
Order Number
FSWL208R/LS
208R/LM
Stock
Insert Number
R L
DCON
LF
LDRED WF
GAMF DMIN
Wrench
0.4
TS21
TKY06F
0.4
TS2
TKY06F
15
10
0.4
TS25
TKY08F
13
12
0.4
TS25
TKY08F
11
13
16
0.8
TS4
TKY15F
11
14
22
0.8
TS4
TKY15F
a a
0201pp
122
25
2.9
17
5.8
FSWL208R/LM
a a
WCMT
WCGT
WCMW
L302pp
125
33
15
FSWL208R/L
a a
0402pp
125
10
FSWL210R/L
a a
0402pp
10
150
12
FSWL212R/L
a a
06T3pp
12
180
15
FSWL216R/L
a a
06T3pp
16
200
20
WCMT
WCMW
RE
Clamp Screw
WCMT
WCGT
FSWL208R/LS
(L3,04,06)
Dimensions(mm)
* Clamp Torque (N m) : TS21=0.6, TS2=0.6, TS25=1.0, TS4=3.5

Steel Shank
Carbide Shank
Work Material
P
M
N
Hardness
Carbon Steel
Alloy Steel
180350HB
Stainless Steel
< 200HB
Aluminium Alloy
l/d < 3
l/d < 5
Cutting
Mode
Cutting Speed
(m/min)
Feed
(mm/rev)
l/d=67
Depth of Cut
(mm)
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Light Cutting
130 (90 160)
0.1 (0.05 0.15)
0.2
120 (80 150)
0.1 (0.05 0.15)
Medium Cutting
90 (60 120)
0.25 (0.15 0.35)
3.0
80 (50 110)
0.15 (0.1 0.2)
Light Cutting
140 (100 180)
0.1 (0.05 0.15)
0.2
140 (100 180)
0.1 (0.05 0.15)
0.2 (0.15 0.25)
2.0
60 (40 80)
0.15 (0.1 0.2)
Medium Cutting
70 (50 90)
0.2
1.5
0.2
1.0
Light Cutting
300 (200 400)
0.1 (0.05 0.15)
0.2
300 (200 400)
0.1 (0.05 0.15)
0.2
Medium Cutting
200 (150 250)
0.1 (0.05 0.15)
2.0
200 (150 250)
0.1 (0.05 0.15)
1.5
WCpp type inserts

CBN & PCD inserts
SPARE PARTS
TECHNICAL DATA
A156
B049, B065
P 001
Q001
E027
BORING BARS
TYPE
BORING BARS
a The minimum cutting

a ISO standard.
a 7 positive insert.
a Screw-on type.
STFC
diameter is from & 11.
TCooinserts
a l/d
is 3 to 5 times the diameter

(up to 7 times with the carbide
shank).
Finish
Finish
FP
Light
FM
Light
LP
LM
60
WF
91
91
GAMF
RE LDRED
Stock
(09,11,16)
Flat top
PCD/CBN
(11,16)
(11)
MM
(09,11,16)
(09,11,16)
Dimensions(mm)
Insert Number
R L
BORING
(09,11,16)
Medium
DCON

Order Number
(09,11,16)
Medium
MP
H
LF
DMIN
(09,11,16)
DCON
LF
LDRED WF
GAMF DMIN
RE
Clamp Screw
Wrench
S08FSTFCR/L09
a a
0902pp
80
12
15
11
0.4
TS22
TKY06F
S10HSTFCR/L11
a a
1102pp
10
100
16
13
13
0.4
TS25
TKY08F
S12KSTFCR/L11
a a
1102pp
12
125
20
11
10
16
0.4
TS25
TKY08F
S16MSTFCR/L11
a a
1102pp
16
150
25
11
14
20
0.4
TS25
TKY08F
S20QSTFCR/L16
a a
16T3pp
20
180
32
13
18
25
0.8
TS4
TKY15F
S25RSTFCR/L16
a a
16T3pp
25
200
40
17
23
32
0.8
TS4
TKY15F
S32SSTFCR/L16
a a
16T3pp
32
250
50
22
30
40
0.8
TS4
TKY15F
TCMT
TCMW
TCMT
STFC
Carbide shank
TCooinserts
Finish
Finish
FP
Light
FM
Light
LP
LM
60
WF
91
91
GAMF
RE LDRED
DMIN
Stock
(09,11,16)
(09,11,16)
(09,11,16)
Medium
Medium
Flat top
PCD/CBN
(11,16)
(11)
MP
MM
DCON
LF

Order Number
(09,11,16)
(09,11,16)
(09,11,16)
Dimensions(mm)
Insert Number
DCON
LF
LDRED WF
C08HSTFCR09
0902pp
100
12
C10KSTFCR11
1102pp
10
125
16
C12MSTFCR11
1102pp
12
150
20
1102pp
16
200
25
11
TCMT
TCMW
TCMT
GAMF DMIN
RE
Clamp Screw
Wrench
15
11
0.4
TS22
TKY06F
13
13
0.4
TS25
TKY08F
11
10
16
0.4
TS25
TKY08F
14
20
0.4
TS25
TKY08F
C16RSTFCR11
C20SSTFCR16
16T3pp
20
250
32
13
18
25
0.8
TS4
TKY15F
C25TSTFCR16
16T3pp
25
300
40
17
23
32
0.8
TS4
TKY15F
a
E028
TCpp type inserts

CBN & PCD inserts
A141 A143
B045, B061
SDUC
DCooinserts
Finish
Finish
FP
Light
FM
LP
Light
LM
50
RE
GAMF
LDRED
Insert Number
S12KSDUCR/L07
a a
S16MSDUCR/L07
a a
S20QSDUCR/L11
a a
S25RSDUCR/L15
a a
S32SSDUCR/L15
a a
S40TSDUCR/L15
a a
MM
Standard
(07,11,15)
(07,11,15)
(07,11,15)
DCMT
DCET
DCGT
DCMW
DCGW
NP-DCGW
NP-DCMT
LDRED WF
F2
(07,11)
DCON
LF
0702pp
10
100
16
2.4
13
13
0.4
TS25
TKY08F
0702pp
12
125
20
3.4
11
10
16
0.4
TS25
TKY08F
0702pp
16
150
25
11
3.9
14
20
0.4
TS25
TKY08F
11T3pp
20
180
32
13
4.4
18
25
0.8
TS4
TKY15F
1504pp
25
200
40
17
6.9
23
32
0.8
TS5
TKY25F
1504pp
32
250
50
22
8.4
30
40
0.8
TS5
TKY25F
1504pp
40
300
63
27
9.4
37
50
0.8
TS5
TKY25F
R L
a a
(07,11)
Flat top
Dimensions(mm)
Stock
S10HSDUCR/L07
(07,11)
Medium
DCON
LF

Order Number
(07,11)
Medium
MP
DMIN
(07,11)
Medium
GAMF DMIN
RE
Clamp Screw Wrench

BORING
93
F2
WF
93
SDUC
Carbide shank
DCooinserts
Finish
Finish
FP
Light
FM
LP
Light
LM
50
93
GAMF
F2
WF
93
RE
DMIN
Insert Number
C12MSDUCR07
C16RSDUCR07
C20SSDUCR11
C25TSDUCR15
MM
Standard
(07,11,15)
(07,11,15)
(07,11,15)
LDRED WF
F2
(07,11)
DCON
LF
0702pp
10
125
16
2.1
13
13
0.4
TS25
TKY08F
0702pp
12
150
20
3.1
11
10
16
0.4
TS25
TKY08F
R
a
(07,11)
Flat top
Dimensions(mm)
Stock
C10KSDUCR07
(07,11)
Medium
DCON
LF

Order Number
(07,11)
Medium
MP
LDRED
(07,11)
Medium
GAMF DMIN
RE
Clamp Screw Wrench
DCMT
DCET
DCGT
DCMW
DCGW
NP-DCGW
NP-DCMT
0702pp
16
200
25
11
3.1
14
20
0.4
TS25
TKY08F
11T3pp
20
250
32
13
3.1
18
25
0.8
TS4
TKY15F
DCMW
DCMT
1504pp
25
300
40
17
4.9
23
32
0.8
TS5
TKY25F

Steel Shank
l/d < 3
Carbide Shank
l/d < 5
Work Material
P
M
N
Hardness
Carbon Steel
Alloy Steel
180350HB
Stainless Steel
< 200HB
Aluminium Alloy
Cutting
Mode
Cutting Speed
(m/min)
Feed
(mm/rev)

l/d=67
Depth of Cut
(mm)
Cutting Speed
(m/min)
Feed
(mm/rev)
Light Cutting
130 (90 160)
0.1 (0.05 0.15)
0.2
120 (80 150)
0.1 (0.05 0.15)
Medium Cutting
90 (60 120)
0.25 (0.15 0.35)
3.0
80 (50 110)
0.15 (0.1 0.2)
Light Cutting
140 (100 180)
0.1 (0.05 0.15)
0.2
140 (100 180)
0.1 (0.05 0.15)
0.2 (0.15 0.25)
2.0
60 (40 80)
0.15 (0.1 0.2)
Medium Cutting
70 (50 90)
Depth of Cut
(mm)
0.2
1.5
0.2
1.0
Light Cutting
300 (200 400)
0.1 (0.05 0.15)
0.2
300 (200 400)
0.1 (0.05 0.15)
0.2
Medium Cutting
200 (150 250)
0.1 (0.05 0.15)
2.0
200 (150 250)
0.1 (0.05 0.15)
1.5
DCpp type inserts

CBN & PCD inserts
SPARE PARTS
TECHNICAL DATA
A132 A135
B043, B044, B060
P 001
Q001
E029
BORING BARS
TYPE
BORING BARS

a ISO standard.
a Screw-on type.
SCLC
CCooinserts
WF
RE
Light
Light
LP
LM
Stock
a a
S10HSCLCR/L06
a a
S12KSCLCR/L06
a a
S16MSCLCR/L09
a a
S20QSCLCR/L09
a a
S25RSCLCR/L12
a a
S32SSCLCR/L12
S40TSCLCR/L12
(06,09)
(06,09)
(06,09)
Medium
Flat top
PCD/CBN
(06,09,12)
(06,09,12)
MM
(06,09,12)
(06,09,12)
Dimensions(mm)
Insert Number
R L
S08FSCLCR/L06
(06,09)
Medium
DCON
LF
DCON
LF
LDRED WF
GAMF DMIN
RE
Clamp Screw
Wrench
0602pp
80
12
15
11
0.4
TS25
TKY08F
0602pp
10
100
16
13
13
0.4
TS25
TKY08F
0602pp
12
125
20
11
10
16
0.4
TS25
TKY08F
09T3pp
16
150
25
11
14
20
0.8
TS4
TKY15F
09T3pp
20
180
32
13
18
25
0.8
TS4
TKY15F
1204pp
25
200
40
17
23
32
0.8
TS5
TKY25F
a a
1204pp
32
250
50
22
30
40
0.8
TS5
TKY25F
a a
1204pp
40
300
63
27
37
50
0.8
TS5
TKY25F
CCMH
CCMT
CCET
CCGT
CCMW
CCGW
NP-CCGW
SCLC
Carbide shank
CCooinserts
Finish
WF
95
GAMF
RE
FM
Light
Light
LP
LM
(06,09)
(06,09)
(06,09)
(06,09)
Medium
Medium
Medium
Flat top
MP
LDRED
DMIN
Stock
C08HSCLCR06
C10KSCLCR06
C12MSCLCR06
C16RSCLCR09
C20SSCLCR09
Standard
(06,09)
(06,09)
(06,09)
Insert Number
CCMH
CCMT
CCET
CCGT
CCMW
CCGW
NP-CCGW
DCON
LF
LDRED WF
(06,09)
Dimensions(mm)
R
a
MM
DCON
LF

Order Number
Finish
FP
60
95
Finish
FM
MP
LDRED
DMIN
BORING
Finish
FP
95
GAMF

shank).
60
95
Order Number
a l/d
GAMF DMIN
RE
Clamp Screw
Wrench
0.4
TS25
TKY08F
0.4
TS25
TKY08F
16
0.4
TS25
TKY08F
20
0.8
TS4
TKY15F
25
0.8
TS4
TKY15F
0602pp
100
12
15
11
0602pp
10
125
16
13
13
0602pp
12
150
20
11
10
09T3pp
16
200
25
11
14
09T3pp
20
250
32
13
18
a
E030
CCpp type inserts

CBN & PCD inserts
A126 A130
B039 B041, B059
F2
107
30
RE
GAMF
Insert Number
S12KSDQCR/L07
a a
S16MSDQCR/L07
a a
S20QSDQCR/L11
a a
S25RSDQCR/L15
a a
S32SSDQCR15
S40TSDQCR15
(07,11)
(07,11)
(07,11)
Medium
Flat top
PCD/CBN
(07,11,15)
(07,11)
MM
(07,11,15)
(07,11,15)
DCON
LF
0702pp
10
100
16
2.4
13
13
0.4
TS25
TKY08F
0702pp
12
125
20
3.4
11
10
16
0.4
TS25
TKY08F
0702pp
16
150
25
11
3.9
14
20
0.4
TS25
TKY08F
11T3pp
20
180
32
13
4.4
18
25
0.8
TS4
TKY15F
1504pp
25
200
40
17
6.9
23
32
0.8
TS5
TKY25F
1504pp
32
250
50
22
8.4
30
40
0.8
TS5
TKY25F
1504pp
40
300
63
27
9.4
37
50
0.8
TS5
TKY25F
R L
a a
(07,11)
Dimensions(mm)
Stock
DCMT
DCET
DCGT
DCMW
DCGW
NP-DCMW
NP-DCMT
Light
LM
DCON
LF
S10HSDQCR/L07
Light
LP
Medium
MP
LDRED
DMIN
Order Number
Finish
FM
50
WF
10730
Finish
FP
LDRED WF
F2
GAMF DMIN
RE
Clamp Screw Wrench

BORING
SDQC
DCooinserts
SDQC
Carbide shank
DCooinserts
Finish
Finish
FP
Light
FM
Light
LP
LM
50
107
30
GAMF
F2
WF
10730
RE
DMIN
Insert Number
C12MSDQCR07
C16RSDQCR07
C20SSDQCR11
C25TSDQCR15
(07,11,15)
(07,11)
MM
(07,11,15)
(07,11,15)
DCON
LF
0702pp
10
125
16
2.1
13
13
0.4
TS25
TKY08F
0702pp
12
150
20
3.1
11
10
16
0.4
TS25
TKY08F
R
a
(07,11)
PCD/CBN
Dimensions(mm)
Stock
C10KSDQCR07
(07,11)
Flat top
DCON
LF

Order Number
(07,11)
Medium
MP
LDRED
(07,11)
Medium
LDRED WF
F2
GAMF DMIN
RE
Clamp Screw Wrench
DCMT
DCET
DCGT
DCMW
DCGW
NP-DCMW
NP-DCMT
0702pp
16
200
25
11
3.1
14
20
0.4
TS25
TKY08F
11T3pp
20
250
32
13
3.1
18
25
0.8
TS4
TKY15F
DCMW
DCMT
1504pp
25
300
40
17
4.9
23
32
0.8
TS5
TKY25F

Steel Shank
Carbide Shank
Work Material
P
M
N
Hardness
Carbon Steel
Alloy Steel
180350HB
Stainless Steel
< 200HB
Aluminium Alloy
l/d < 3
l/d < 5
Cutting
Mode
Cutting Speed
(m/min)
Feed
(mm/rev)
Light Cutting
130 (90 160)
0.1 (0.05 0.15)
Medium Cutting
90 (60 120)
0.25 (0.15 0.35)
Light Cutting
140 (100 180)
Medium Cutting
70 (50 90)
l/d=67
Depth of Cut
(mm)
Cutting Speed
(m/min)
Feed
(mm/rev)
0.2
120 (80 150)
0.1 (0.05 0.15)
3.0
80 (50 110)
0.15 (0.1 0.2)
0.1 (0.05 0.15)
0.2
140 (100 180)
0.1 (0.05 0.15)
0.2 (0.15 0.25)
2.0
60 (40 80)
0.15 (0.1 0.2)
Depth of Cut
(mm)
0.2
1.5
0.2
1.0
Light Cutting
300 (200 400)
0.1 (0.05 0.15)
0.2
300 (200 400)
0.1 (0.05 0.15)
0.2
Medium Cutting
200 (150 250)
0.1 (0.05 0.15)
2.0
200 (150 250)
0.1 (0.05 0.15)
1.5
DCpp type inserts

CBN & PCD inserts
SPARE PARTS
TECHNICAL DATA
A132 A135
B043, B044, B060
P 001
Q001
E031
BORING BARS
TYPE
BORING BARS

a ISO standard.
a Screw-on type.
SVQC
VCooinserts
F2
WF
GAMF
RE
Finish
FM
BORING
a a
S20QSVQCR/L11
a a
S25RSVQCR/L16
a a
S32SSVQCR/L16
S40TSVQCR16
Light
LM
(11,16)
(11,16)
(11,16)
(11,16)
Medium
Medium
Flat top
MM
Standard
DCON
LF
(16)
(16)
(11,16)
(11,16)
Dimensions(mm)
Insert Number
DCON
R L
S16MSVQCR/L11
Light
LP
Medium

Stock
Finish
FP
MP
LDRED
DMIN
Order Number

shank).
50
11730
117
30
a l/d
LF LDRED WF
F2
GAMF DMIN
RE
Clamp Screw Wrench
1103pp
16
150
25
11
3.9
14
20
0.4
TS25
TKY08F
1103pp
20
180
32
13
4.4
18
25
0.4
TS25
TKY08F
1604pp
25
200
40
17
6.9
23
32
0.8
TS4
TKY15F
a a
1604pp
32
250
50
22
8.4
30
40
0.8
TS4
TKY15F
1604pp
40
300
63
27
9.4
37
50
0.8
TS4
TKY15F
VCMW
VCMT
SVQC
Carbide shank
VCooinserts
F2
WF
GAMF
RE
C20SSVQCR11
C25TSVQCR16
(11,16)
(11,16)
(11,16)
(11,16)
Medium
Medium
Flat top
MM
Standard
(16)
(16)
(11,16)
(11,16)
Dimensions(mm)
Insert Number
C16RSVQCR11
Light
LM
DCON
LF

Stock
Light
LP
Medium
MP
LDRED
DMIN
Order Number
Finish
FM
50
11730
117
30
Finish
FP
VCMT
VCMW
DCON
LF LDRED WF
F2
GAMF DMIN
RE
Clamp Screw Wrench
1103pp
16
200
25
11
3.1
14
20
0.4
TS25
TKY08F
1103pp
20
250
32
13
3.1
18
25
0.4
TS25
TKY08F
1604pp
25
300
40
17
4.9
23
32
0.8
TS4
TKY15F
a
E032
VCpp type inserts

CBN & PCD inserts
A151, A152
B049, B064
SSKC
SCooinserts
Finish
Finish
FP
Light
FM
Light
LP
LM
60
WF
75
RE
GAMF
DMIN
(09)
(09)
Medium
Flat top
MP
LDRED
(09)
Medium
Insert Number
DCON
R L
a a
S20QSSKCR/L09
a a
S25RSSKCR/L12
a a
(09,12)
(09,12)
(09,12)
SCMW
SCMT
LF LDRED WF
(09,12)
Dimensions(mm)
Stock
S16MSSKCR/L09
Standard
DCON
LF

Order Number
MM
GAMF DMIN
RE
Clamp Screw
Wrench
09T3pp
16
150
25
11
14
20
0.8
TS4
TKY15F
09T3pp
20
180
32
13
18
25
0.8
TS4
TKY15F
1204pp
25
200
40
17
23
32
0.8
TS5
TKY25F
BORING
75
(09)
Medium
SVUC
VCooinserts
Finish
Finish
FP
Light
FM
Light
LP
LM
50
93
GAMF
F2
WF
93
RE
DMIN
Insert Number
R L
a a
S25RSVUCR/L16
a a
S32SSVUCR/L16
a a
S40TSVUCR/L16
a a
(11,16)
Flat top
MM
Standard
(16)
(16)
(11,16)
VCMW
VCMT
DCON
LF LDRED WF
F2
(11,16)
Dimensions(mm)
Stock
S20QSVUCR/L11
(11,16)
Medium
DCON
LF

Order Number
(11,16)
Medium
MP
LDRED
(11,16)
Medium
GAMF DMIN
RE
Clamp Screw Wrench
1103pp
20
180
32
13
4.4
18
25
0.4
TS25
TKY08F
1604pp
25
200
40
17
6.9
23
32
0.8
TS4
TKY15F
1604pp
32
250
50
22
8.4
30
40
0.8
TS4
TKY15F
1604pp
40
300
63
27
9.4
37
50
0.8
TS4
TKY15F

Steel Shank
Carbide Shank
Work Material
P
M
N
Carbon Steel
Alloy Steel
Hardness
180350HB
Stainless Steel
< 200HB
Aluminium Alloy
l/d < 3
l/d < 5
l/d=67
Cutting
Mode
Cutting Speed
(m/min)
Feed
(mm/rev)
Light Cutting
130 (90 160)
0.1 (0.05 0.15)
Medium Cutting
90 (60 120)
0.25 (0.15 0.35)
Light Cutting
140 (100 180)
0.1 (0.05 0.15)

0.2 (0.15 0.25)
2.0
Medium Cutting
70 (50 90)
Depth of Cut
(mm)
Cutting Speed
(m/min)
Feed
(mm/rev)
0.2
120 (80 150)
0.1 (0.05 0.15)
3.0
80 (50 110)
0.15 (0.1 0.2)
0.2
140 (100 180)
0.1 (0.05 0.15)
60 (40 80)
0.15 (0.1 0.2)
Depth of Cut
(mm)
0.2
1.5
0.2
1.0
Light Cutting
300 (200 400)
0.1 (0.05 0.15)
0.2
300 (200 400)
0.1 (0.05 0.15)
0.2
Medium Cutting
200 (150 250)
0.1 (0.05 0.15)
2.0
200 (150 250)
0.1 (0.05 0.15)
1.5
SCpp type inserts

VCpp type inserts
CBN inserts
A138, A139
A151, A152
B049
SPARE PARTS
TECHNICAL DATA
P001
Q001
E033
BORING BARS
TYPE
BORING BARS

a ISO standard.
a Screw-on type.
SCZC
CCooinserts
WF
GAMF
LH RE
DMIN

shank).
Finish
FP
95
F2
a l/d
Finish
Light
FM
Light
LP
LM
(06,09)
(06,09)
(06,09)
(06,09)
Medium
Medium
Flat top
PCD/CBN
(06,09)
(06,09)
MP
MM
DCON
LF
LDRED

Order Number
Stock
Insert Number
DCON LF LDRED LH
BORING
R L
S16MSCZCR/L06
a a
S20QSCZCR/L09
a a
(06,09)
(06,09)
Dimensions(mm)
CCMH
CCMT
CCET
CCGT
CCMW
WF
F2
GAMF DMIN RE
Clamp Screw
Wrench
0602pp
16
150
36
11
11
14
10
20
0.4
TS25
TKY08F
09T3pp
20
180
50
18
13
18
25
0.8
TS4
TKY15F
(Note 2) When using insert with right and left hand chip breaker, please use right hand
insert for right hand holder and left hand insert for left hand holder.

Work Material
P
M
N
E034
Hardness
Carbon Steel
Alloy Steel
180350HB
Stainless Steel
< 200HB
Aluminium Alloy
Cutting
Mode
l/d < 3
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Cutting Speed
(m/min)
Feed
(mm/rev)
Light Cutting
130 (90 160)
0.1 (0.05 0.15)
0.2
120 (80 150)
0.1 (0.05 0.15)
Medium Cutting
90 (60 120)
0.25 (0.15 0.35)
3.0
80 (50 110)
0.15 (0.1 0.2)
Light Cutting
140 (100 180)
0.1 (0.05 0.15)
0.2
140 (100 180)
0.1 (0.05 0.15)
0.2 (0.15 0.25)
2.0
60 (40 80)
0.15 (0.1 0.2)
Medium Cutting
70 (50 90)
Depth of Cut
(mm)
0.2
1.5
0.2
1.0
Light Cutting
300 (200 400)
0.1 (0.05 0.15)
0.2
300 (200 400)
0.1 (0.05 0.15)
0.2
Medium Cutting
200 (150 250)
0.1 (0.05 0.15)
2.0
200 (150 250)
0.1 (0.05 0.15)
1.5

CCpp type inserts

CBN & PCD inserts
A126 A130
B039 B041, B059
PSKN

a ISO standard.
a Lever lock type.
SNooinserts
With coolant hole
Finish
FH
WF
LDRED
RE
a a
A32SPSKNR/L12
a a
(09,12)
(12)
(12)
(12)
Stainless
G class
CBN
Standard
MM
(09,12)
RE
DMIN
R/L
(12)
(09,12)
*2
Dimensions(mm)
WF
R L
A25RPSKNR/L12
Medium
MH
Medium
Right hand tool

holder shown.
1 Pin Lock Type

LDRED
Insert Number
LF
DCON
a a
DCON
LF
GAMF
75
A20QPSKNR/L09
Medium
MP
75
GAMF
Stock
Light
LP
IN
DM
Order Number
(12)
*2
Clamp Clamp
Clamp Pin
Shim Shim
Pin Lever Screw Wrench Plug
Pin
SNMA 0903pp 20 180 32 13 18 13 25 0.8
SNMG
SNMM 1204pp 25 200 40 17 23 13 32 0.8 MLSP42

SNGA
pp
LLSSN42
LLP14
LLCL14
LLCS108S
1204
32
250
50
22
30
13
44
0.8
SNGG
Screw
HKY15R
HKY25R
HKY15R
HKY30R
HGMPT1/8 HP3T P208AM HSS03005

HGMPT1/4 HP43 P210AM HSS03005
HGMHKY30R PT3/8
BORING
TYPE
BORING BARS
Lock Type : A20QPSKNR/L09, A25RPSKNR/L12

*12 Pin
Clamp Torque (N m) : LLCS108S=3.3, HP3T=2.2, HP43=3.3
*
PTFN
TNooinserts
With coolant hole
Finish
FH
Medium
MP
Medium
MH
WF
DMIN
91
GAMF
LDRED
RE
H
DCON
LF
*Dimensions(mm)
A20QPTFNR/L16
a a
A25RPTFNR/L16
a a
A32SPTFNR/L16
a a
A40TPTFNR/L22
a a
A50UPTFNR/L22
a a
1604pp
TNMA
1604pp
TNMG
TNMM 1604pp
TNGA
pp
TNGG 2204
2204pp
DMIN
20 180 32 13 18 15 25
25 200 40 17 23 13 32
32 250 50 22 30 13 44
40 300 63 27 37 10 54
50 350 80 35 47
(16)
(16,22)
(16,22)
Stainless
G class
CBN
MM
(16,22)
R/L
(16,22)
(16,22)
*2
GAMF
WF
LDRED
LF
Insert Number
R L
DCON
Stock
(16)
Medium
Standard
Right hand tool

holder shown.
1 Pin Lock Type
9 70
RE
91
Order Number
Light
LP
(16)
*2
Clamp Clamp
Clamp Pin
Shim Shim
Pin
Screw
HKY15R
HKY25R
HKY15R
HKY25R
HGM
0.8
PT1/8 HP31 P208AM HSS03005
HGM
0.8 MLTP32
PT1/4 HP33 P208AM HSS03005
HGM
0.8 LLSTN32 LLP13 LLCL13 LLCS106 HKY25R PT3/8

HGM
0.8 LLSTN42 LLP14 LLCL14 LLCS108S HKY30R PT3/8

HGM
0.8 LLSTN42 LLP14 LLCL14 LLCS108S HKY30R PT3/8
Lock Type : A20QPTFNR/L16, A25RPTFNR/L16

*12 Pin
Clamp Torque (N m) : LLCS106=2.2, LLCS108S=3.3, HP31=2.2, HP33=2.2
*

Work Material
Carbon Steel
Alloy Steel
Stainless Steel
Gray Cast Iron
Hardness
Cutting
Mode
l/d < 3
l/d=34
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
180350HB Medium Cutting
110 (80 140)
0.25 (0.1 0.4)
5.0
110 (80 140)
0.2 (0.1 0.3)
4.0
Medium Cutting
80 (60 100)
0.2 (0.1 0.3)
4.0
70 (50 100)
0.15 (0.1 0.25)
3.0
Tensile Strength Medium Cutting

< 350MPa
80 (60 100)
0.25 (0.1 0.4)
5.0
80 (60 100)
0.2 (0.1 0.3)
4.0
< 200HB
SNpp type inserts
TNpp type inserts
CBN & PCD inserts
A105 A109
A110 A115
B028 B031, B056
SPARE PARTS
TECHNICAL DATA
P001
Q001
E035
BORING BARS
TYPE
BORING BARS
PDUN

a ISO standard.
a Lever lock type.
DNooinserts
With coolant hole
Finish
LP
F2
WF
LDRED
BORING
A20QPDUNR/L11
a a
A25RPDUNR/L11
a a
A25RPDUNR/L15
a a
A32SPDUNR/L11
a a
A32SPDUNR/L15
a a
A40TPDUNR/L15
a a
A50UPDUNR/L15
a a
Medium
MH
(15)
(15)
(15)
Stainless
G class
CBN
Standard
MM
(11,15)
RE
DMIN
GAMF
F2
WF
R/L
(15)
(15)
*2
Clamp Clamp
Clamp Pin
Shim Shim
Pin Lever Screw Wrench Plug Pin
25 200 40 17 6.9 23 15 32 0.8 LLSDN32 LLP13 LLCL23 LLCS106 HKY25R

25 200 40 17 6.9 23 13 32 0.8 MLDP42
HKY15R
HKY30R
32 250 50 22 8.4 30 13 44 0.8 LLSDN32 LLP13 LLCL23 LLCS106 HKY25R

32 250 50 22 8.4 30 13 44 0.8 LLSDN42 LLP14 LLCL24 LLCS108S HKY30R
40 300 63 27 9.4 37 10 54 0.8 LLSDN42 LLP14 LLCL24 LLCS108S HKY30R
1504pp 50 350 80 35 12.4 47
(15)
*2
Dimensions(mm)
1104pp 20 180 32 15 6.4 18 13 26 0.8

1104pp
DNMA
DNMG 1504pp
DNMX
1104pp
DNMM
DNGA 1504pp
DNGG
1504pp
(15)
Medium
Right hand tool

holder shown.
1 Pin Lock Type
LDRED
R L
LF
Insert Number
DCON
H
DCON
LF
RE
Stock
Medium
MP
93
GAMF
Order Number
Light
FH
IN
DM
93
9 70 0.8 LLSDN42 LLP14 LLCL24 LLCS108S HKY30R
HGMPT1/8
HGMPT1/4
HGMPT1/4
HGMPT3/8
HGMPT3/8
HGMPT3/8
HGMPT3/8
Screw
HP43 P210AM HSS03005
Lock Type : A25RPDUNR/L15

*12 Pin
Clamp Torque (N m) : LLCS125=1.5, LLCS106=2.2, LLCS108S=3.3, HP43=3.3
*
PCLN
With coolant hole
CNooinserts
GAMF
RE LDRED
H
DCON
LF
*Dimensions(mm)
09T3pp
(12)
(12)
(12)
(12)
Medium
Stainless
CBN
MH
Standard
(12)
(09,12)
(12)
*2
20 180 32 13 18 13 25 0.8
LLCL13S LLCS105
25 200 40 17 23 13 32 0.8
LLCL13S LLCS105
HKY25R HGMHKY15R PT1/8

HGMHKY20R PT1/8
HGMHKY20R PT1/4
HKY30R HGMHKY15R PT1/4
HGMHKY30R PT3/8
HGMHKY30R PT3/8
HGMHKY30R PT3/8
HGMLLCL13S LLCS105 HKY20R PT1/8
LF
Screw
16 150 25 11 14 15 20 0.8
a a
A20QPCLNR/L09N
a a
A25RPCLNR/L09
a a
A25RPCLNR/L12
a a
A32SPCLNR/L12
a a
A40TPCLNR/L12
a a
1204pp 40 300 63 27 37 10 54 0.8 LLSCN42 LLP14 LLCL14 LLCS108S
A50UPCLNR12
1204pp 50 350 80 35 47 10 63 0.8 LLSCP42 LLP14 LLCL14 LLCS108S
*
*
(12)
Clamp Clamp
Clamp Pin
Shim Shim
Pin
A20QPCLNR/L09
09T3pp 20 180 32 13 18 13 25 0.8

09T3pp
CNMA
CNMG 09T3pp
CNMM 1204pp
CNGG
1204pp
MM
*2
DMIN
GAMF
WF
LDRED
DCON
Insert Number
R L
A16MPCLNR/L09
Medium
MP
Medium
Right hand tool

holder shown.
1 Pin Lock Type
RE
a a
Light
LP
95
WF
95
Stock
Light
SA
IN
DM
Order Number
Finish
FH
25 200 40 17 23 13 32 0.8 MLCP42
32 250 50 22 30 13 44 0.8 LLSCN42 LLP14 LLCL14 LLCS108S
HP3T P208AM HSS03005
HP43 P210AM HSS03005
1 Pin Lock Type : A20QPCLNR/L09, A25RPCLNR/L12

2 Clamp Torque (N m) : LLCS105=1.5, LLCS106=2.2, LLCS108S=3.3, HP3T=2.2, HP43=3.3
DNpp type inserts

a
E036
CNpp type inserts

CBN & PCD inserts
A098 A103
A092 A097
B022 B027, B055
PWLN
WNooinserts
With coolant hole
Light
SH
IN
95
Medium
MP
DM
WF
(06)
GAMF
LDRED
RE
MM
DCON
LF
RE
DMIN
GAMF
WF
R L
LDRED
DCON
Insert Number
LF
Stock
Order Number
(06)
Dimensions(mm)
Clamp Lever Clamp Screw
Wrench
Plug
HGMPT1/8
HGMPT1/8
HGMPT1/4
A16MPWLNR/L06
a a
16 150 25
11
14 15 20 0.8 LLCL13S
LLCS105
HKY20R
A20QPWLNR/L06
a a
WNMG 06T3pp 20 180 32
13
18 13 25 0.8 LLCL13S
LLCS105
HKY20R
A25RPWLNR/L06
a a
06T3pp 25 200 40
17
23 13 32 0.8 LLCL13S
LLCS105
HKY20R
06T3pp
BORING
95
(06)
Stainless
* Clamp Torque (N m) : LLCS105=1.5
PDQN
With coolant hole
DNooinserts
Finish
FH
Light
Medium
LP
MP
Medium
MH
IN 10730
LDRED
A25RPDQNR/L15
a a
A32SPDQNR/L15
a a
A40TPDQNR/L15
a a
A50UPDQNR15
DNMA
DNMG
DNMM
DNGA
DNGG
(15)
(15)
(15)
(15)
Medium
Stainless
G class
CBN
Standard
Right hand tool

holder shown.
1 Pin Lock Type
RE
DMIN
F2
WF
R/L
(15)
(15)
*2
(15)
*2
Clamp Clamp
Clamp Pin
Shim Shim
1504pp 25 200 40 17 6.9 23 13 32 0.8 MLDP42

1504pp 32 250 50 22 8.4 30 13 44 0.8 LLSDN42
1504pp 40 300 63 27 9.4 37 10 54 0.8 LLSDN42
1504pp 50 350 80 35 12.4 47
MM
(15)
Dimensions(mm)
LDRED
Insert Number
R L
LF
Stock
DCON
Order Number
LF
H
DCON
GAMF
107
30
RE
GAMF
F2
WF
DM
9 70 0.8 LLSDN42
Screw
HGM
HKY15R
HKY30R PT1/4 HP43 P210AM HSS03005
HGMLLP14 LLCL24 LLCS108S HKY30R PT3/8
Lock Type : A25RPDQNR/L15

*12 Pin
Clamp Torque (N m) : LLCS108S=3.3, HP43=3.3
*

Work Material
Carbon Steel
Alloy Steel
Stainless Steel
Gray Cast Iron
Hardness
Cutting
Mode
l/d < 3
l/d=34
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
110 (80 140)
0.25 (0.1 0.4)
5.0
110 (80 140)
0.2 (0.1 0.3)
4.0
Medium Cutting
80 (60 100)
0.2 (0.1 0.3)
4.0
70 (50 100)
0.15 (0.1 0.25)
3.0

< 350MPa
80 (60 100)
0.25 (0.1 0.4)
5.0
80 (60 100)
0.2 (0.1 0.3)
4.0
< 200HB
WNpp type inserts

DNpp type inserts
CBN & PCD inserts
A119 A122
A098 A103
B025 B027, B055
SPARE PARTS
TECHNICAL DATA
P001
Q001
E037
BORING BARS
PDZN
WF
With coolant hole
BORING
A25RPDZNR/L15
a a
A32SPDZNR/L15
a a
A40TPDZNR/L15
a a
A50UPDZNR/L15
a a
H
DCON
LF
Light
Medium
LP
MP
(15)
(15)
(15)
(15)
Stainless
G class
CBN
MM
(15)
R/L
(15)
(15)
*2
RE
DMIN
GAMF
Medium
MH
Medium
Standard
Dimensions(mm)
Finish
FH
Right hand tool

holder shown.
1 Pin Lock Type
F2
R L
RE
LDRED
LF
Insert
Number
DCON
F2
25
DMIN
Stock
DNooinserts
93
GAMF
WF
Order Number

a ISO standard.
a Lever lock type.
LDRED
TYPE
BORING BARS
(15)
*2
Clamp Clamp
Clamp Pin
Shim Shim
Screw
HGMDNMA 1504pp 25 200 65 17 6.7 23 13 32 0.8 MLDP42
HKY15R
HKY30R PT1/4 HP43 P210AM HSS03005
DNMG
HGM
DNMX 1504pp 32 250 75 22 8.2 30 13 40 0.8 LLSDN42 LLP14 LLCL24 LLCS108S HKY30R PT3/8
DNMM 1504pp 40 300 88 27 9.2 37 10 50 0.8 LLSDN42 LLP14 LLCL24 LLCS108S HKY30R HGMPT3/8
DNGA
HGMpp
LLSDN42
LLP14
LLCL24
LLCS108S
HKY30R
1504
50
350
105
35
12.2
47
9
63
0.8
DNGG
PT3/8
(Note 2) When using insert with right and left hand chip breaker, please use right hand
insert for right hand holder and left hand insert for left hand holder.
1 Pin Lock Type : A25RPDZNR/L15
2 Clamp Torque (N m) : LLCS108S=3.3, HP43=3.3
*
*

Work Material
Carbon Steel
Alloy Steel
Stainless Steel
Gray Cast Iron
E038
Hardness
Cutting
Mode
l/d < 3
l/d=34
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
110 (80 140)
0.25 (0.1 0.4)
5.0
110 (80 140)
0.2 (0.1 0.3)
4.0
Medium Cutting
80 (60 100)
0.2 (0.1 0.3)
4.0
70 (50 100)
0.15 (0.1 0.25)
3.0

< 350MPa
80 (60 100)
0.25 (0.1 0.4)
5.0
80 (60 100)
0.2 (0.1 0.3)
4.0
< 200HB

DNpp type inserts

CBN & PCD inserts
A098 A103
B025 B027, B055
TYPE
BORING HEAD

a Lever lock type.
a Exchangeable head type.
DPTF
TNooinserts
Finish
Light
FH
SH
Medium
MP
Medium
MH
LF
WF
90
BD
DMIN
(16,22)
(16)
(16,22)
(16,22)
Insert Number
BD
LF
WF GAMF DMIN RE
TNMA
TNMG
TNMM
TNGA
TNGG
1604pp
32
40
20
12
40
0.8 LLSTN32
LLP13
2204pp
40
50
25
10
50
0.8 LLSTN42
LLP14
Shim
Shim Pin
Clamp
Lever
Clamp
Screw
Wrench
BORING
DPTF140R
CBN
MM
Dimensions(mm)
R
a
(16,22)
Please refer to page E041 for arbor.
DPTF132R
(16,22)
G class
Standard
Stock
(16,22)
Stainless
RE
GAMF
Order Number
(16)
Medium
DPDU
DNooinserts
Finish
Light
FH
SH
Medium
MP
Medium
MH
LF
GAMF
Please refer to page E041 for arbor.
Order Number
Stock
DPDU140R
(15)
(15)
(15)
Stainless
G class
CBN
(15)
(15)
MM
RE
6
(15)
(15)
Dimensions(mm)
Insert Number
BD
LF
WF GAMF DMIN RE
1504pp
32
40
25
10
50
0.8 LLSDN42
LLP14
1504pp
40
50
30
60
0.8 LLSDN42
LLP14
DPDU132R
(15)
Medium
Standard
WF
93
BD
DMIN
DNMA
DNMG
DNMX
DNMM
DNGA
DNGG
Shim
Shim Pin
Clamp
Lever
Clamp
Screw
Wrench
Clamp Torque (N m) : LLCS108=3.3
TNpp type inserts
DNpp type inserts
CBN & PCD inserts
A110 A115
A098 A103
B025 B027, B030, B031, B055, B056
SPARE PARTS
TECHNICAL DATA
P001
Q001
E039
BORING BARS
TYPE
BORING HEAD

a Lever lock type.
DPCL
CNooinserts
Finish
Light
FH
SA
Light
LP
Medium
MP
LF
DMIN
WF
95
BD
(12)
(12)
(12)
(12)
Medium
Medium
Stainless
CBN
MH
Standard
MM
5
RE
GAMF 6
Please refer to page

E041 for arbor.
Order Number
Stock
BORING
(12)
(12)
(12)
Insert Number
(12)
Dimensions(mm)
BD
LF
WF GAMF DMIN RE
32
40
20
12
40
0.8 LLSCN42
LLP14
40
50
25
10
50
0.8 LLSCN42
LLP14
CNMA
a
1204pp
DPCL132R
CNMG
CNMM
a
1204pp
DPCL140R
CNGG
DPDH
DNooinserts
Shim
Clamp
Lever
Shim Pin
Finish
Light
FH
LP
Clamp
Screw
Wrench
Medium
MP
Medium
MH
LF
(15)
(15)
(15)
Stainless
G class
CBN
(15)
(15)
Standard
GAMF 6
MM
Stock
DPDH132R
DPDH140R
(15)
(15)
Dimensions(mm)
Insert Number
BD
LF
WF GAMF DMIN RE
1504pp
32
40
25
10
50
0.8 LLSDN42
LLP14
1504pp
40
50
30
60
0.8 LLSDN42
LLP14
(15)
Medium
RE
Please refer to page

E041 for arbor.
Order Number
BD
107
30
WF
DMIN
1730
DNMA
DNMG
DNMM
DNGA
DNGG
Shim
Clamp
Lever
Shim Pin
Wrench
CNpp type inserts

a
E040
Clamp
Screw
DNpp type inserts

CBN & PCD inserts
A092 A097
A098 A103
B022 B027, B055
DPVP
VNooinserts
Finish
FH
Light
Medium
SH
Medium
MP
MH
LF
BD
Stock
DPVP140R
(16)
CBN
(16)
(16)
MM
L-F
(16)
(16)
Dimensions(mm)
Insert Number
BD
LF
WF GAMF DMIN RE
VNMG
VNGA
VNGG
1604pp
32
40
25
13
50
0.8
PV322
P11S
HSP05008C
E03
HKY25R
1604pp
40
50
30
13
60
0.8
PV322
P11S
HSP05008C
E03
HKY25R
Shim
STANDARD ARBOR FOR D TYPE BORING HEAD

z
zDesignation
32
xArbor Length (mm)

Symbol DCON
1
1.5
32
cArbor Diameter (mm)

Diameter(DCON)
Symbol
vHead Diameter (mm)

Diameter(BD)
Symbol
LF
OAL
32
260
300
32
32
32
32
40
310
360
40
40
40
40
Dimensions (mm)
Order
Number
Stock
(16)
PCD
DPVP132R
(16)
G class
RE
10
GAMF
Order Number
(16)
Stainless
BORING
117
30
WF
DMIN
2730
B13232
32
B14040
40
DCON LF
Set Bolt
Wrench
Head
Order Number
300
SD32
HKY60R
DPpp132R
360
SD40
HKY60R
DPpp140R
OAL
260
29
310
37
DCON
LF
OAL
VNpp type inserts

CBN & PCD inserts
A116 A118
B032, B033, B057
SPARE PARTS
TECHNICAL DATA
P001
Q001
E041
BORING BARS
AL
TYPE
BORING BARS
a Suitable for non-ferrous metal.

a Screw-on type.
STFE
a Excellent vibration resistance.

a The minimum cutting diameter is
from & 20.
TEooinserts
Medium
PCD
R/L
R/L
DMIN
(16)
WF
91
3
RE
H
DCON
LDRED 10
LF

Order Number
Insert Number
DCON
LF
1603pp
16
200
30
1603pp
20
200
1603pp
25
250
BORING
R L
S16RSTFER/L16
a a
S20RSTFER/L16
a a
S25SSTFER/L16
a a
(16)
Dimensions(mm)
Stock
TEGX...R/L
(16)
PCD
LDRED WF
DMIN
RE
11
14.6
20
37
13
18
40
17
23
Clamp Screw
Wrench
0.4
FC400890T
TKY10F
25
0.4
FC400890T
TKY10F
32
0.4
FC400890T
TKY10F
* Clamp Torque (N m) : FC400890T=2.5

Work Material
Aluminium Alloy
Grade
HTi10
MD220
Cutting Speed
(m/min)
400
(200600)
800
(2001500)
l/d=3
l/d=4
l/d=5
l/d=6
Feed
(mm/rev)
Depth of Cut
(mm)
Feed
(mm/rev)
Depth of Cut
(mm)
Feed
(mm/rev)
Depth of Cut
(mm)
Feed
(mm/rev)
Depth of Cut
(mm)
0.15
(0.050.25)
0.15
(0.050.25)
3.0
0.15
(0.050.25)
0.15
(0.050.25)
3.0
0.1
(0.050.2)
0.1
(0.050.2)
2.5
0.1
(0.050.2)
0.1
(0.050.2)
1.0
3.0
3.0
2.5
1.0
a
E042
TEpp type inserts

PCD inserts
A144
B066
SPARE PARTS
TECHNICAL DATA
P001
Q001
Memo
E043

OF GROOVING
aHow this section page is organized
zClassified according to external or internal applications.
xSub-classified according to product series.
[For External Grooving]
[For Internal Grooving]

uses illustrations and arrows to depict available machining
applications such as cutting off, grooving, and copying.
MIN. CUTTING
DIAMETER
INDICATION OF HOLDER TYPE ACCORDING TO APPLICATION
is colour-coded to let
you find, at a glance,
the minimum cutting
diameters for internal
machining.
indicates the holder types, such as the standard type or the L type,
according to machining application.
TITLE OF PRODUCT
PRODUCT FEATURES
INDICATION OF EXTERNAL/
FACE GROOVING/INTERNAL
APPLICATION
PRODUCT SECTION
GEOMETRY
EXTERNAL GROOVING
INTERNAL GROOVING
FTYPE
GYSERIES (EXTERNAL GROOVING)

1
00 type holder
Insert GY2Mooooooooo-GS
-GM Insert GY2Gooooooooo-MF
Insert GY2Mooooooooo-GU Insert GY2Mooooooooo-MS
Insert GY1Gooooooooo- GF
GS Insert GY2Mooooooooo-MM
a Min. cutting diameter 10mm

a Screw-on type
a Usable for various applications.
a Max. groove depth : 3mm
FSL51
(Note 1) Please order the modular blade and modular holder separately.
(Note 2) Please set the right hand modular blade at the right hand holder and the left hand
modular blade at the left hand holder.
1 Corner type (FSL5108R,5110R)
Fig. A
Fig. B
Fig. E
Fig. F
Order Number
Stock
Insert Number
R
Type
CW
CDX
CUTDIA
Modular
Mono Block
Modular
Modular
6
12
Mono Block
Modular
Modular
Modular
Modular
10
20
Modular
Modular
2.00
2.24
Modular
12
24
Modular
Modular
Modular
18 4
Mono Block
36
Modular
Modular
Mono Block
20 1
40 2
Modular
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
GYHR1616J00-M20R
GYHL1616J00-M20L
GYQR2020K00-D06
GYQL2020K00-D06
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYQR2525M00-D06
GYQL2525M00-D06
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR1616J00-M20R
GYHL1616J00-M20L
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR1616J00-M20R
GYHL1616J00-M20L
GYQR2020K00-D18
GYQL2020K00-D18
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYQR2525M00-D20
GYQL2525M00-D20
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Modular Blade
GYM20RA-D06
GYM20LA-D06
GYM20RA-D06
GYM20LA-D06
GYM25RA-D06
GYM25LA-D06
GYM25RA-D06
GYM25LA-D06
GYM25RA-D06
GYM25LA-D06
GYM25RA-D06
GYM25LA-D06
GYM20RA-D10
GYM20LA-D10
GYM20RA-D10
GYM20LA-D10
GYM25RA-D12
GYM25LA-D12
GYM25RA-D12
GYM25LA-D12
GYM25RA-D12
GYM25LA-D12
GYM25RA-D12
GYM25LA-D12
GYM20RB-D18
GYM20LB-D18
GYM20RB-D18
GYM20LB-D18
GYM25RA-D20
GYM25LA-D20
GYM25RA-D20
GYM25LA-D20
GYM25RA-D20
GYM25LA-D20
GYM25RA-D20
GYM25LA-D20
Stock
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
G
G
A
A
C
C
G
G
A
A
E
E
E
E
C
C
A
A
C
C
A
A
E
E
E
E
D
D
G
G
B
B
D
D
G
G
B
B
F
F
F
F
GROOVING
GROOVING
Seat
Size
2 Corner type (FSL5112R,5114R,5116R)
Insert GY2Mooooooooo-BM Insert GY2Mooooooooo-GS

-GM
Insert GY2Mooooooooo-GU
Insert GY2MoooooR/Loo-GM
Dimensions (mm)
Internal grooving, Threading
*
*
Dimensions(mm)
DCON
LF
LU
WF
CW
1.2
1.5
2.0
1.5
2.0
3.0
2.0
3.0
4.0
Grooving
Threading
FSL5108R
MLG10ppL
MLT1001L
125
30
4.8
FSL5110R
MLG10ppL
MLT1001L
10
150
40
5.8
FSL5112R
MLG14ppL
MLT1401L
12
180
50
6.8
10.8
FSL5114R
MLG14ppL
MLT1401L
14
180
60
7.8
12.4
FSL5116R
MLG20ppL
MLT2001L
16
200
70
9.7
14
10
*2
Max.
Groove
Depth
1
DMIN (mm)
Clamp
Wrench
Screw
1.0
TS25 TKY08F
12
1.0
TS25 TKY08F
14
2.0
TS32 TKY08F
16
2.0
TS32 TKY08F
20
3.0
TS43 TKY15F

2 Clamp Torque (N m) : TS25=1.0, TS32=1.0, TS43=3.5
FSL52
(Carbide shank) Internal grooving, Threading

Order Number
Stock
R
Insert Number
Grooving
Threading
*2
Dimensions(mm)
DCON
LF
LU
WF
*1
CW
DMIN
1.2
1.5
2.0
1.5
2.0
3.0
2.0
3.0
4.0
10
FSL5208R
MLG10ppL
MLT1001L
125
60
4.8
FSL5210R
MLG10ppL
MLT1001L
10
150
70
5.8
FSL5212R
MLG14ppL
MLT1401L
12
180
80
6.8
10.8
FSL5214R
MLG14ppL
MLT1401L
14
180
85
7.8
12.4
FSL5216R
MLG20ppL
MLT2001L
16
200
115
9.7
14
Max.
Groove
Depth
(mm) Clamp Wrench
Screw
1.0
TS25 TKY08F
12
1.0
TS25 TKY08F
14
2.0
TS32 TKY08F
16
2.0
TS32 TKY08F
20
3.0
TS43 TKY15F

*12 DMIN
maximum groove depth varies according to the insert used. Please refer to the maximum groove depth of inserts on pages F012F014.
*12 The
maximum cut off diameter CUTDIA varies according to the insert used. The cut off diameter is double the maximum groove depth (CDX) of inserts on pages F012F014.
*3 The
Dimensions shown are when the gauge insert is used. If other insert geometries are used then LF, LH, LH 2 and WF values may vary.
*4 The
maximum groove depth is limited by the workpiece diameter. For details, please refer to page F104.
*
a
F030
F130

PRODUCT STANDARDS
indicates order numbers, stock status
(per right/left hand), holders, Modular Blade,
groove widths, maximum groove depths,
maximum cut-off diameters, dimensions,
applicable inserts, and cutting edge shapes.
a To Order :
F000
For holder, please specify zorder number and hand of tool (right/left).
For insert, please specify zinsert number and xgrade.
LEGEND FOR
STOCK STATUS MARK
spread.
TURNING TOOLS
GROOVING
CLASSIFICATION (EXTERNAL CUTTING) .....
CLASSIFICATION (INTERNAL CUTTING) ......
REFERENCE MATERIAL .................................
QUICK INDEX ...................................................
STANDARD OF GROOVING TOOLS
EXTERNAL CUTTING
FEATURES OF THE GY SERIES ..............
GY SERIES ORDER NUMBER ..................
GY SERIES INSERTS ................................
GY SERIES QUICK INDEX ........................
GY SERIES.................................................
UG HOLDER ..............................................
MG HOLDER ..............................................
SMG HOLDER............................................
INTERNAL CUTTING
GY SERIES.................................................
MICRO-MINI BORING BARS ............................
MICRO-MINI TWIN BORING BARS ..................
F TYPE BORING BARS........................................
D TYPE BORING HEAD .......................................
F002
F003
F015
F016
F004
F010
F012
F016
F028
F120
F122
F124
F094
F125
F126
F130
F132

*F125
CoooR-BLS
F126
F132
F130
F130
F028
F120
F121
F122
F123
F131
F131
F128
F129
F124
F124
F124
F121
F120
CG
DPT4
FSL51
FSL52
GY
KGBN
KGT
MGH
MGT
MLG
MLT
RBH
SBH
SMGH
SMGT
SMTT
UGH
UGHN
F001
GROOVING
CLASSIFICATION
EXTERNAL CUTTING
GROOVING
UG Holder
MG Holder
Spring clamp type.

Strengthened insert clamping.
Block and blade type and
solid type series.
a Maximum cut off diameter : 120mm.
a
a
a
Clamp-on type.
Precision class insert.
a Positive insert suffers from
negligible chattering and thus
produces a good finished surface.
a
a
Screw-on type.
a Positive insert suffers from
negligible chattering and thus
produces a good finished surface.
a
a
CTAH
a
a
a
SMALL TOOLS
3
3.18
4.75
5
4.75
5
6.35
8
6.35
Face Grooving
Recessing
Copying
2.5
3
3.18
F028
F120
1.25
F122
0.5
F124
1.3
0.3
D016
3.0
1.5
2.0
1.5
2.0
1.5
2.0
D020
2.2
2.5
2.2
2.5
2.2
2.5
D021
For gang type tool posts.

Small Shank : 16mm
High cutting edge sharpness and
excellent chip discharge.
a Maximum cut off diameter :
2335mm
2.5
2.5
2.5
D022

Small Shank : 16mm
a Maximum cut off diameter :
2335mm
3.0
3.0
3.0
D023
a
a
a
a
a
F002
2.2
3.1
4.1
5.1
2.5
2
2.24
2.39
2.5
2.74
3
3.18
3.24
4
4.24
4.75
5
5.24
6
6.31
6.35
D018
CTEH
2.2
3.1
4.1
5.1
0.7
1.0
1.5
2.0
CTDH
2.2
3.1
4.1
5.1
0.7
1.0
1.5
2.0
CTCH
1.5
2
2.24
2.39
2.5
2.74
3
3.18
3.24
4
4.24
4.75
5
5.24
6
6.31
6.35
8
Page
0.7
1.0
1.5
2.0
a
a
CTBH

Small Shank : 8mm16mm
Possible to control the back clamping.
High rigidity due to design of
vertical insert.
Economical due to the design of
three-corner inserts.
Due to the design of handed tool holders,
able to minimize accumulation of
workpieces.
High rigidity due to design of vertical insert.
Maximum cut off diameter : 12mm
Single holder for inserts for back
turning and cutting off.
High rigidity due to design of vertical
insert.
Small Shank : 10mm,12mm
1.5
2
2.24
2.39
2.5
2.74
3
3.18
3.24
4
4.24
4.75
5
5.24
6
6.31
6.35
8
a
a
a
a
1.5
2
2.24
2.39
2.5
2.74
3
3.18
3.24
4
4.24
4.75
5
5.24
6
6.31
6.35
8
GTAH
GTBH GTCH
Modular blade type

a Clamp-on type.
a The modular blade allows for
high rigidity and accuracy.
(Tri Lock System)
a Various insert types.
Mono block type
a Spring clamp type.
SMG Holder
Features
Cutting Off
GY Series
Insert Shape
Deep Grooving
Name of Tool Holder
Shallow Grooving
Groove Width According to Cutting Mode (mm)
a
a
a
a
a
a
EXTERNAL CUTTING
a
a
a
Face Grooving
Copying
Page
0.6
D027
For cam type tool posts.

Small Shank : 712mm
Single holder responds to front turning, 0.25
back turning, grooving, threading and
cutting off operations.
a The most suitable for machining of small
1.5
parts with work diameter 5mm or smaller.
a Maximum groove depth : 0.32.5mm
a Maximum cut off diameter : 35mm
CSVH
Cutting Off
Features
Deep Grooving
Insert Shape
SMALL TOOLS
Name of Tool Holder
Shallow Grooving
Groove Width According to Cutting Mode (mm)
1.5
Name of Tool Holder
Insert Shape
GY Series
Features
a
a
40
3.0
1.2
1.0
4.0
3.0
1.25
1.2
4.5
4.5
1.0
1.0
2.0
2.0
2.0
1.0
3.2
13
Solid carbide type.

Insert can be ground to suit the
application.
10
6.35
MICRO-MINI
Boring Bars
Solid carbide type.

Economical due to single holder
with two cutting edges.
2
25
a
a
(mm)
MICRO-MINI TWIN
Boring Bars
Pin lock type.

Exchangable head type.
(mm)
a
a
a
(mm)
DPT4
Max.
Groove
Depth
FSL5
Groove
Width
Modular blade type

a Clamp-on type.
a The modular blade allows for high
rigidity and accuracy.
(Tri Lock System)
Mono block type
a Spring clamp type.
a Screw-on type.
a Precision class insert.
a Holder is capable of performing
both grooving and threading.
a Maximum groove depth : 3mm.
Min.
Cutting
Diameter
3.0
2.0
Page
GROOVING
INTERNAL CUTTING
F094
F130
F132
F126
F125
F003
EXTERNAL GROOVING / INTERNAL GROOVING
GY
New Tri Lock System for increased
SERIES
GY series offers ultimate rigidity and

accuracy for stable grooving.
stability and performance!

a Innovative Tri Lock System
a Mitsubishi Materials has developed a new and unique, modular blade system.
The Tri-Lock system ensures the blade is securely fixed in 3 directions (side, front and top)
giving high rigidity for a stable grooving performance.
Lock
GROOVING
Lock
Lock
Lock
Lock
Lock
Lock
Lock
Lock
Modular Blade for

External / Internal Grooving
Modular Blade for

External Grooving
GU Breaker
(VP20RT)
(VP10RT)
GS Breaker
GM Breaker
(MY5015)
Modular Blade for

Face Grooving
Flat Top
(NX2525)
MF Breaker
(CBN)
MS Breaker
MM Breaker
BM Breaker
Blank Insert
(RT9010)
(RT9020)
F004
Easy to use modular blade system allows flexible tool management but
maintains an overall strength comparable to a mono block type holder.
Modular Holder for

Internal Grooving
GROOVING
Modular Holder for

External / Face Grooving
A wide variety of products with

assorted combinations to consolidate
necessary tools for diverse grooving
applications.
Original insert design leading the

way to new grooving applications !
a Highly reliable insert clamping

a Safety keys prevent insert movement.
a The convex geometry ensures

high precision clamping.
Convex
contact
face
F005
GYSERIES
A wide selection of holders and inserts

available for diverse grooving applications.
External Face holders
GROOVING
a Corresponding blades to a variety of modular holders with different shank sizes.
1010
1212
1616
2012
2020
2525
3225
3232
1616
Mono block type
2525
3225
3232
Modular type
a A wide selection of holders
and inserts available for

diverse grooving applications
External grooving
2020
a Applicable for various diameters of face
grooves by the wide array of modular

blades with different grooving diameters.
Face grooving
Same holder
Internal holders
a A wide range of holders available
from minimum diameter of 25mm.
Mono block type

Min.cutting diameter
&25, &32
Modular type
Min.cutting diameter
&40, &50,
&60, &70
a Short shank types are standard
stocked.
Mono block type
Short
F006
Standard
Modular type
Short
Standard
Original insert design leading the way to

new grooving applications.
a Highly reliable insert clamping
The convex geometry ensures
high precision clamping.
Convex
contact
face
Comparison of finished surface
Rigidity comparison
GY series can achieve stable machining at the cutting conditions

which created vibration with a conventional modular type tool.
The GY series provides rigidity comparable to a mono block

type grooving tool.
0.20
Conventional modular type

Deflection (mm)
Workpiece
: SCM440
Insert width
: 5mm
Feed
: 0.2mm/rev
Groove depth : 23mm
0.15
GY
0.10
Competitor's
mono block type
0.05
Conventional
modular type
GY
GROOVING
Safety keys prevent insert movement.
500
1000
(Tool body for 5mm insert)
Load (N)
New TRI-LOCK System for increased

stability and performance!
a TRI-LOCK System
The TRI-LOCK system ensures the blade is securely fixed in 3 directions (side, front
and top), giving high rigidity for stable grooving performance.
Lock
Lock
Lock
Lock
Lock
Lock
Lock
Lock
Lock
F007
INSERT
a A WIDE SELECTION OF INSERTS
Breaker system
Selection of groove widths
Grooving
GUBreaker
GSBreaker
(For Gummy Steel)
GM
Breaker
(Medium feeds)
(Low feeds)
(For hardened steel)
Different corner radii available
Copying/For recessing
GROOVING
For Multifunctional Grooving
GFGS
MFBreaker
(G class)
MSBreaker
MM
Breaker
(Medium feeds)
(Low feeds)
BMBreaker
MF Breaker
Cutting Off
Efficient chip breaking

when cross-feed
machining.
GUBreaker
(For Gummy Steel)
GSBreaker
GM
Breaker
(Medium feeds)
(Low feeds)
R/L05-GMBreaker
(Medium feeds)
Chips are controlled

when finish machining.
a INSERT GRADE
Work Material
Machining
Condition
Steel
Stainless Steel
Cast Iron
Heat resistant Alloy / Titanium Alloy
Hardened steel
Stable
NX2525
VP10RT
MY5015
MY5015
Machining
Condition
VP10RT
VP10RT
RT9010
VP10RT
VP20RT
VP20RT
VP20RT
VP20RT
Unstable
Note1) VP20RT is the first recommended grade for materials other than hardened steel.
Note2) For VP10RT, VP20RT and MY5015, wet cutting is recommended.
F008
MB8025
VP20RT (1st Recommendation)
MY5015
a PVD coated grade suitable for a wide range
a MY5015 is a CVD coated grade with
of applications. The combination of a special

tough cemented carbide substrate with
MIRACLE coating provides an excellent
balance of wear and fracture resistance.
excellent wear resistance even at high

temperatures. It provides longer tool life
when machining cast and ductile cast irons.
Also suitable for high speed continuous
cutting of steels.
CVD Coated Carbide
MIRACLE Coating
Tough cemented carbide substrate
(HRA90.5)
VP10RT (2nd Recommendation)

a PVD coated grade with a cemented carbide
substrate harder than VP20RT. For use on

difficult to cut materials and for extending
tool life.
RT9010
a First recommended grade for Titanium alloys.
Not recommended for use on non-ferrous alloys.
GROOVING
NX2525
MIRACLE Coating
(HRA92.0)
a NX2525, a cermet grade for finish machining of steels and for good
surface finishes at lower cutting speeds.
MB8025
a MB8025 is a sintered CBN grade for hardened steel.
a BLANK INSERTS
Blank inserts for custom grinding

RT9010/RT9020 for insert blank
a First recommendation on insert blank is RT9020 due to the tougher
carbide substrate and suitable for a wide range of application.

RT9010 is a harder substrate than RT9020 and is ideal for long tool
life on stable cutting applications.
Coating is recommended for application on steel, stainless steel
and cast iron materials.
1 Edge Type
2 Edge Type
blank is not suitable for machining without grinding.

* Insert
Refer to the following URL for more information.
http://www.mitsubishicarbide.net/contents/mmc/ja/manual/blank_inserts.pdf
F009
GY SERIES ORDER NUMBER

y INSERT
z
GY
0300
030
05
zSeries Description
bSeat Size
cPeripheral
xNumber of Teeth
2
2 Edge Type
Sintered
Blank
E
F
1.50mm
0200
2.00mm
GROOVING
vGroove Width
0150
0800
8.00mm
*1
nCorner Radius
1.50mm
2.00mm
2.24mm
2.39mm
2.50mm
2.74mm
3.00mm
3.18mm
3.24mm
4.00mm
4.24mm
4.75mm
5.00mm
5.24mm
6.00mm
6.31mm
6.35mm
8.00mm
G
H
J
K
.Application 1
/Application 2
010
0.10mm
Grooving/Cutting off
015
0.15mm
Multifunctional
Finishing
B Copying (Ball shape)
Low feeds
Medium feeds
1 Edge Type
Ground
400
4.00mm
For Gummy Steel
,Lead angle (R/L type insert)

05
mHand
N
Neutral
Right
Left
y CBN INSERT
z
11
u
12
u
GY
0300
020
GS
11 Application 3
u
Honing Type
GS General Purpose
Flat Top
*1 Select a seat size with the same symbol as that of modular blade and mono block holder.
y MODULAR BLADE
a EXTERNAL/INTERNAL/FOR RECESSING
zSeries Description
GY
M25
12
xModular Blade Size
cHand
Right
Standard Type
M25
Left
Reinforced Type
For recessing
Face Grooving
005
0.5mm
06
6mm
25
25mm
a FACE GROOVING
z
GY
M25
12
050
mMin. Groove Diameter

035
35mm
040
40mm
250
250mm
Select a seat size with the same symbol as that of the insert.
*12 The
maximum groove depth is a value when used for external grooving and changes according to the insert used.
* For internal
grooving, refer to the maximum groove depth on pages F094F100.
3 GYM20R/LA-o10, GYM20R/LA-o12, GYM25R/LA-o12 and GYM25R/LA-o14 can be used for both external
* and internal grooving.
F010
nMax. Groove Depth 2
bSeat Size 1
2.00mm
2.24mm
2.39mm
E
2.50mm
2.74mm
3.00mm
F
3.18mm
3.24mm
4.00mm
G
4.24mm
4.75mm
H
5.00mm
5.24mm
6.00mm
J
6.31mm
6.35mm
vModular Blade Type
M20
*3
y EXTERNAL/FACE GROOVING/FOR RECESSING

a MONO BLOCK HOLDER
x
GY
2525
00
25
cHand of Holder
vShank Diameter(H x W)
bHolder Length
mSeat Size
1010
10mmx10mm
110mm
Left
1212
12mmx12mm
JX
120mm
1616
16mmx16mm
125mm
2012
20mmx12mm
150mm
170mm
xHolder Type
S
Mono block type for Swiss style lathes
2020
20mmx20mm
With mono block offset
2525
25mmx25mm
Q Without mono block offset
3225
32mmx25mm
3232
32mmx32mm
Modular holder
E
F
G
nAngle
00
50
50
90
90
,Max. Groove Depth
1.50mm
2.00mm
2.24mm
2.39mm
2.50mm
2.74mm
3.00mm
3.18mm
3.24mm
4.00mm
4.24mm
4.75mm
5.00mm
5.24mm
6.00mm
6.31mm
6.35mm
8.00mm
H
J
K
06
6mm
08
8mm
Right
*1
25
25mm
GROOVING
zSeries Description
a MODULAR HOLDER
z
GY
2525
00
M25
.Modular Blade Size
/Hand of Modular Blade
M20
Right
M25
Left
*1 Select a seat size with the same symbol as that of the insert.
y INTERNAL
a MONO BLOCK HOLDER
zSeries Description
GY
20
90
06
cHand of Holder
vShank Diameter
bHolder Length
Right
20
20mm
125mm
Left
25
25mm
140mm
32
32mm
150mm
40
40mm
170mm
xHolder Type
A
Mono Block
Modular holder
50
50mm
180mm
200mm
250mm
300mm
nAngle
90
.Max. Groove Depth
90
06
6mm
07
7mm
30mm
40mm
50mm
60mm
80mm
,Seat Size 1
2.00mm
D
2.24mm
2.39mm
E
2.50mm
2.74mm
3.00mm
F
3.18mm
3.24mm
4.00mm
G
4.24mm
4.75mm
H
5.00mm
5.24mm
6.00mm
J
6.31mm
6.24mm
mNeck Length
a MODULAR HOLDER
z
11
u
GY
40
90
M25
10 Modular Blade Size

u
11 Hand of Modular Blade

u
M20
Right
M25
Left
*1 Select a seat size with the same symbol as that of the insert.
F011
EXTERNAL GROOVING / FACE GROOVING / INTERNAL GROOVING
GY INSERTS
INSERTS
GU Breaker
(For gummy steel)
CW
RE0.05
RE0.05
CDX
GROOVING
L0.1
RE0.05
CW
For Grooving / Cutting off
GS Breaker
(Low feeds)
RE0.05
CDX
L0.1
GM Breaker
(Medium feeds)
CW
RE0.05
RE0.05
CDX
L0.1
R/L05-GM Breaker
CW
For Cutting off
RE0.05
5
CDX
L0.1
Order Number
GY2M0200D020N-GU
GY2M0239E020N-GU
GY2M0250E020N-GU
GY2M0300F030N-GU
GY2M0318F030N-GU
GY2M0400G030N-GU
GY2M0475H040N-GU
GY2M0500H040N-GU
GY2M0600J040N-GU
GY2M0635J040N-GU
GY2M0150C010N-GS
GY2M0200D020N-GS
GY2M0239E020N-GS
GY2M0250E020N-GS
GY2M0300F020N-GS
GY2M0318F020N-GS
GY2M0400G020N-GS
GY2M0475H030N-GS
GY2M0500H030N-GS
GY2M0600J030N-GS
GY2M0635J030N-GS
GY2M0800K030N-GS
GY2M0150C020N-GM
GY2M0200D020N-GM
GY2M0239E020N-GM
GY2M0250E020N-GM
GY2M0300F030N-GM
GY2M0318F030N-GM
GY2M0400G030N-GM
GY2M0475H040N-GM
GY2M0500H040N-GM
GY2M0600J040N-GM
GY2M0635J040N-GM
GY2M0800K050N-GM
GY2M0200D020R05-GM
GY2M0200D020L05-GM
GY2M0250E020R05-GM
GY2M0250E020L05-GM
GY2M0300F030R05-GM
GY2M0300F030L05-GM
GY2M0400G030R05-GM
GY2M0400G030L05-GM
GY2M0500H040R05-GM
GY2M0500H040L05-GM
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
*2 L dimension depends on the breaker. Refer to F015 table.
F012
a a a a

(10 inserts in one case) (CBN inserts are available in 1 piece in one case.)
RT9010
RT9020
MB8025
Geometry
VP10RT
VP20RT
MY5015
NX2525
Applications
Stock
Coated Cermet Carbide CBN
Dimensions (mm)
CW
Seat
Size Grooving
RE
Tolerance
Width
D
E
E
F
F
G
H
H
J
J
C
D
E
E
F
F
G
H
H
J
J
K
C
D
E
E
F
F
G
H
H
J
J
K
D
D
E
E
F
F
G
G
H
H
CDX
*2
2.00 0.03 0.2 19.7 20.70

2.39 0.03 0.2 19.8 20.70
2.50 0.03 0.2 19.5 20.70
3.00 0.03 0.3 19.3 20.70
3.18 0.03 0.3 19.3 20.70
4.00 0.04 0.3 24.2 25.65
4.75 0.04 0.4 24.2 25.65
5.00 0.04 0.4 24.2 25.65
6.00 0.04 0.4 24.2 25.65
6.35 0.04 0.4 24.2 25.65
1.50 0.03 0.1 13.4 14.70
2.00 0.03 0.2 18.7 20.70
2.39 0.03 0.2 18.5 20.70
2.50 0.03 0.2 18.5 20.70
3.00 0.03 0.2 18.5 20.70
3.18 0.03 0.2 18.5 20.70
4.00 0.04 0.2 23.9 25.65
4.75 0.04 0.3 23.9 25.65
5.00 0.04 0.3 24.0 25.65
6.00 0.04 0.3 24.1 25.65
6.35 0.04 0.3 24.1 25.65
8.00 0.04 0.3 29.1 30.50
1.50 0.03 0.2 13.9 14.70
2.00 0.03 0.2 19.4 20.70
2.39 0.03 0.2 19.4 20.70
2.50 0.03 0.2 19.4 20.70
3.00 0.03 0.3 19.4 20.70
3.18 0.03 0.3 19.4 20.70
4.00 0.04 0.3 24.4 25.65
4.75 0.04 0.4 24.3 25.65
5.00 0.04 0.4 24.3 25.65
6.00 0.04 0.4 24.3 25.65
6.35 0.04 0.4 24.3 25.65
8.00 0.04 0.5 29.3 30.50
2.00 0.03 0.2 19.5 20.80
2.00 0.03 0.2 19.5 20.80
2.50 0.03 0.2 19.5 20.825
2.50 0.03 0.2 19.5 20.825
3.00 0.03 0.3 19.5 20.85
3.00 0.03 0.3 19.5 20.85
4.00 0.04 0.3 24.5 25.85
4.00 0.04 0.3 24.5 25.85
5.00 0.04 0.4 24.5 25.95
5.00 0.04 0.4 24.5 25.95
Flat Top (For hardened steel)
CW
For Grooving
3.0
RE0.05
7 RE0.05
MF Breaker
(Finishing)
*
*
*
CW
RE0.05
RE0.05
CDX
L0.05
*
*
MS Breaker
(Low feeds)
CW
RE0.05
RE0.05
CDX
L0.1
GY1G0200D020N-GFGS
GY1G0239E020N-GFGS
GY1G0250E020N-GFGS
GY1G0300F020N-GFGS
GY1G0318F020N-GFGS
GY1G0400G020N-GFGS
GY1G0475H020N-GFGS
GY1G0500H020N-GFGS
GY2G0200D020N-MF
1GY2G0224D015N-MF
GY2G0239E020N-MF
GY2G0250E020N-MF
1GY2G0274E020N-MF
GY2G0300F020N-MF
GY2G0300F040N-MF
GY2G0318F020N-MF
GY2G0318F040N-MF
1GY2G0324F020N-MF
GY2G0400G020N-MF
GY2G0400G040N-MF
GY2G0400G080N-MF
1GY2G0424G020N-MF
GY2G0475H020N-MF
GY2G0475H040N-MF
GY2G0475H080N-MF
GY2G0500H020N-MF
GY2G0500H040N-MF
GY2G0500H080N-MF
1GY2G0524H020N-MF
GY2G0600J020N-MF
GY2G0600J040N-MF
GY2G0600J080N-MF
1GY2G0631J020N-MF
GY2G0635J020N-MF
GY2G0635J040N-MF
GY2G0635J080N-MF
GY2M0200D020N-MS
GY2M0250E020N-MS
GY2M0300F020N-MS
GY2M0300F040N-MS
GY2M0400G020N-MS
GY2M0400G040N-MS
GY2M0500H040N-MS
GY2M0500H080N-MS
GY2M0600J040N-MS
GY2M0600J080N-MS
GY2M0800K080N-MS
a
a
a
a
a
a
a
a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a
Dimensions (mm)
CW
Seat
Size Grooving
Tolerance
Width
D
E
E
F
F
G
H
H
D
D
E
E
E
F
F
F
F
F
G
G
G
G
H
H
H
H
H
H
H
J
J
J
J
J
J
J
D
E
F
F
G
G
H
H
J
J
K
RE
*2
CDX
2.00 0.03 0.2

2.39 0.03 0.2
20.70
20.70
2.50 0.03 0.2
20.70
3.00 0.03 0.2
20.70
3.18 0.03 0.2
20.70
4.00 0.03 0.2
25.65
4.75 0.03 0.2

5.00 0.03 0.2
25.65
25.65
2.00 0.02 0.2

2.24 0.02 0.15
19.5 21.05
19.8 21.05
2.39 0.02 0.2
19.2 21.05
2.50 0.02 0.2
19.4 21.05
2.74 0.02 0.2
19.7 21.05
3.00 0.02 0.2
19.5 21.05
3.00 0.02 0.4
19.3 21.05
3.18 0.02 0.2
19.5 21.05
3.18 0.02 0.4
19.3 21.05
3.24 0.02 0.2
19.5 21.05
4.00 0.02 0.2
24.9 25.95
4.00 0.02 0.4
24.7 25.95
4.00 0.02 0.8
24.3 25.95
4.24 0.02 0.2
24.9 25.95
4.75 0.02 0.2
24.4 25.95
4.75 0.02 0.4
24.2 25.95
4.75 0.02 0.8
23.8 25.95
5.00 0.02 0.2
24.4 25.95
5.00 0.02 0.4
24.2 25.95
5.00 0.02 0.8
23.8 25.95
5.24 0.02 0.2
24.4 25.95
6.00 0.02 0.2
24.4 25.95
6.00 0.02 0.4
24.2 25.95
6.00 0.02 0.8
23.8 25.95
6.31 0.02 0.2
24.4 25.95
6.35 0.02 0.2
24.4 25.95
6.35 0.02 0.4

6.35 0.02 0.8
24.2 25.95
23.8 25.95
2.00 0.03 0.2

2.50 0.03 0.2
19.1 20.70
19.1 20.70
3.00 0.03 0.2
19.2 20.70
3.00 0.03 0.4
18.9 20.70
4.00 0.04 0.2
24.2 25.65
4.00 0.04 0.4
23.9 25.65
5.00 0.04 0.4
23.9 25.65
5.00 0.04 0.8
23.5 25.65
6.00 0.04 0.4
23.9 25.65
6.00 0.04 0.8

8.00 0.04 0.8
23.5 25.65
28.5 30.50
GROOVING
Order Number
RT9010
RT9020
MB8025
Geometry
VP10RT
VP20RT
MY5015
NX2525
Applications
Stock
*1 Circlip corresponding width of cut
F013
EXTERNAL GROOVING / FACE GROOVING / INTERNAL GROOVING
GY INSERTS
INSERTS
RE0.05
CW
GROOVING
MM Breaker
(Medium feeds)
RE0.05
CDX
L0.1
RE0.05
CW
For Copying / For Recessing
BM Breaker
CDX
L0.1
2 Edge Type
Blank
*1
CW
RE
RE
L
1 Edge Type
CW
RE
RE
L
Order Number
GY2M0200D020N-MM
GY2M0250E020N-MM
GY2M0300F020N-MM
GY2M0300F040N-MM
GY2M0300F080N-MM
GY2M0400G020N-MM
GY2M0400G040N-MM
GY2M0400G080N-MM
GY2M0500H040N-MM
GY2M0500H080N-MM
GY2M0600J040N-MM
GY2M0600J080N-MM
GY2M0800K080N-MM
GY2M0800K120N-MM
GY2M0200D100N-BM
GY2M0250E125N-BM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY2M0400G200N-BM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY2M0600J300N-BM
GY2M0635J318N-BM
GY2M0800K400N-BM
GY2B0220D020N
GY2B0270E020N
GY2B0340F020N
GY2B0420G020N
GY2B0520H020N
GY2B0655J020N
GY1B0220D020N
GY1B0270E020N
GY1B0340F020N
GY1B0420G020N
GY1B0520H020N
GY1B0655J020N
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a
a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a
blank is not suitable for machining without grinding.

*1 Insert
Refer to the following URL for more information.
F014
http://www.mitsubishicarbide.net/contents/mmc/ja/manual/blank_inserts.pdf
2 L dimension depends on the breaker. Refer to F015 table.

RT9010
RT9020
MB8025
Geometry
VP10RT
VP20RT
MY5015
NX2525
Applications
Stock
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
a a
Dimensions (mm)
CW
Seat
Size Grooving
Tolerance
Width
D
E
F
F
F
G
G
G
H
H
J
J
K
K
D
E
F
F
G
H
H
J
J
K
D
E
F
G
H
J
D
E
F
G
H
J
RE
CDX
*2
2.00 0.03 0.2

2.50 0.03 0.2
19.1 20.70
19.1 20.70
3.00 0.03 0.2
19.1 20.70
3.00 0.03 0.4
18.9 20.70
3.00 0.03 0.8
18.5 20.70
4.00 0.04 0.2
24.1 25.65
4.00 0.04 0.4
23.9 25.65
4.00 0.04 0.8
23.5 25.65
5.00 0.04 0.4
23.9 25.65
5.00 0.04 0.8
23.5 25.65
6.00 0.04 0.4
23.9 25.65
6.00 0.04 0.8
23.5 25.65
8.00 0.04 0.8

8.00 0.04 1.2
28.5 30.50
28.1 30.50
2.00 0.03 1.00

2.50 0.03 1.25
19.5 20.90
19.3 20.90
3.00 0.03 1.50
19.0 20.90
3.18 0.03 1.59
18.9 20.90
4.00 0.04 2.00
23.4 25.80
4.75 0.04 2.38
22.9 25.80
5.00 0.04 2.50
22.8 25.80
6.00 0.04 3.00
22.5 25.90
6.35 0.04 3.18

8.00 0.04 4.00
22.3 25.90
26.5 30.80
2.20 0.10 0.2

2.70 0.10 0.2
21.05
21.05
3.40 0.10 0.2
21.05
4.20 0.10 0.2
26.00
5.20 0.10 0.2

6.55 0.10 0.2
26.00
26.00
2.20 0.10 0.2

2.70 0.10 0.2
21.07
21.10
3.40 0.10 0.2
21.00
4.20 0.10 0.2
25.86
5.20 0.10 0.2

6.55 0.10 0.2
25.90
25.90
Reference material
C-TYPE CIRCLIP STANDARDS LIST
Application
Width (Tolerance)
Standard
For shaft
C-type stop ring
For
shaft
For
hole
C-type concentric
stop ring
For
shaft
0.5
0.7
0.8
0.9
1.1
1.3
1.6
1.85
2.15
2.65
3.15
4.15
5.15
For
hole
E-type stop ring
ANSI B27.7/27.8 (US)

BS 3673 (UK)
DIN 471/472 (De)
NF E 22 163 (Fr)
UNI 7435/7438 (It)
+0.14
0
3.531
+0.18
0
+0.051
0
+0.076
0
+0.102
0
+0.127
0
1.15
1.35
1.75
1.95
2.2
2.7
3.2
4.2
+0.14
0
+0.18
0
+0.152
0
9
1.1
1.3
1.6
1.85
2.15
2.65
3.15
4.15
5.15
6.2
+0.051
0
0.457
+0.14
0
+0.18
0
0.737
0.991
1.168
1.422
1.727
2.184
2.616
3.048
+0.076
0
+0.102
0
+0.127
0
+0.22
0
+0.22
0
JIS B 2804 (JP)
6.2
N1*** American
0.32
0.5
0.7
1.0
1.2
1.4
For
shaft
0.305
0.457
0.737
0.991
1.168
1.422
1.727
2.184
2.616
3.048
For hole
0.305
0.457
0.584
0.737
0.991
1.168
1.422
1.727
+0.05
0
+0.10
0
+0.14
0
+0.051
0
+0.076
0
+0.102
0
0.3
0.4
0.5
0.7
0.9
1.15
1.75
2.2
+0.05
0
GROOVING
Category
+0.10
0
+0.14
0
O-RING STANDARDS
Category
Standard
For
stable
DIN 3770/3771 (De)

JIS B 2401 (JP)
ISO 3601
SMS 1586/1588 (Se)
BS 1806/4518 (UK)
For
dynamic
Width (Tolerance)
For oil pressure
General
3.2
4.0
7.5
11.0
2.54
3.18
4.32
6.1
8.0
+0.13
0
+0.2
0
2.5
3.2
4.7
7.5
11.1
2.39
3.58
4.78
7.14
9.58
SAE AS-568 (US)
1.9
2.3
+0.1
0
2.9
+0.15
0
3.6
4.5
5.5
7.0
+0.14
0
+0.25
0
+0.2
0
+0.3
0
8.6
+0.4
0
10.7
+0.5
0
For air pressure
2.3
3.1
3.7
6.4
9.0
+0.2
0
2.4
3.6
4.8
7.1
9.5
+0.25
0
2.3
3.1
3.7
6.4
9.0
+0.2
0
2.2
3.4
4.6
6.9
9.3
+0.25
0
G-class insert with MF breaker is available for single-step machining.

Conventional GY series insert is available for single-step machining.
Machined in multiple steps or by cross feed machining.
L dimension tolerance conversion table

Grooving Width
CW
(mm)
*1 Dimensions
L (mm)
1.50
2.00
2.24
2.39
2.50
2.74
3.00
3.18
3.24
4.00
4.24
4.75
5.00
5.24
6.00
6.31
6.35
8.00
14.70
20.70
3 (20.7)
20.70
20.70
3 (20.7)
20.70
20.70
3 (20.7)
25.65
3 (25.65)
25.65
25.65
3 (25.65)
25.65
3 (25.65)
25.65
30.50
*
*
*
*
*
*
*2 Dimensional tolerance (mm) versus standard dimension (L) of each breaker

GU
GS/GM
MS/MM
0
0
0
0
0
0
0
0
Flat Top
MF
BM
0.10
-0.30
0.20
0.125
-0.30
-0.30
0
0
0.15
-0.30
-0.30
0.20
-0.35
0
0
0
0
0.30
-0.35
-0.35
0
0
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
value is used at the described holder dimension.

*12 This
y when there is no applicable breaker.
*3 The standard dimensions shown here use an approximate insert width.
*
R/L-GM
0.20
0.20
0.20
0.15
0.15
0.15
0.25
0.25
0.30
F015
QUICK INDEX
List for selecting modular holder from modular blade
(For External and Internal Grooving)
Modular Blade
Seat
Size
Order
Number
Hand
(R/L)
GYM20RA-D06
GYM20LA-D06
GROOVING
GYM20RA-D10
GYM20LA-D10
GYM20RB-D18
GYM20LB-D18
GYM25RA-D06
GYM25LA-D06
GYM25RA-D12
GYM25LA-D12
GYM25RA-D20
GYM25LA-D20
F016
Modular holder
Order
Number
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHL2020K90-M20R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHR2020K90-M20L
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHL2020K90-M20R
GYDL32L90C-M20R
GYDL32S90C-M20R
GYDL40M90D-M20R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHR2020K90-M20L
GYDR32L90C-M20L
GYDR32S90C-M20L
GYDR40M90D-M20L
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHL2020K90-M20R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHR2020K90-M20L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYDL40T90D-M25R
GYDL40M90D-M25R
GYDL40T90D-M25R
GYDL50P90F-M25R
GYDL50T90F-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
GYDR40T90D-M25L
GYDR40M90D-M25L
GYDR40T90D-M25L
GYDR50P90F-M25L
GYDR50T90F-M25L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
Cutting Holder
Hand Mode angle Page
(R/L)
R
R
L
L
L
R
R
R
L
L
L
L
L
L
R
R
R
R
R
R
L
L
L
R
R
R
R
R
L
L
L
L
L
R
R
R
R
R
L
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
R
L
L
L
L
L
R
Ext.
Seat
Size
00 F030
Modular Blade
Modular holder
Order
Number
Hand
(R/L)
Order
Number
GYM20RA-E06
90 F044
Ext.
00 F030
GYM20LA-E06
90 F044
Ext.
00 F030
90 F044
GYM20RA-E10
Int.
Ext.
90 F094
00 F030
90 F044
Int.
Ext.
90 F094
GYM20LA-E10
00 F030
90 F044
Ext.
GYM20RB-E18
00 F030
90 F044
GYM20LB-E18
Ext.
00 F030
90 F044
Ext.
GYM25RA-E06
00 F030
E
90 F044
Ext.
GYM25LA-E06
00 F030
90 F044
GYM25RA-E12
Int.
Ext.
90 F094
00 F030
90 F044
GYM25LA-E12
Int.
Ext.
90 F094
00 F030
GYM25RA-E20
90 F044
Ext.
00 F030
90 F044
GYM25LA-E20
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHL2020K90-M20R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHR2020K90-M20L
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHL2020K90-M20R
GYDL32L90C-M20R
GYDL32S90C-M20R
GYDL40M90D-M20R
GYDL40T90D-M20R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHR2020K90-M20L
GYDR32L90C-M20L
GYDR32S90C-M20L
GYDR40M90D-M20L
GYDR40T90D-M20L
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHL2020K90-M20R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHR2020K90-M20L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYDL40M90D-M25R
GYDL40T90D-M25R
GYDL50P90F-M25R
GYDL50T90F-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
GYDR40M90D-M25L
GYDR40T90D-M25L
GYDR50P90F-M25L
GYDR50T90F-M25L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
Cutting Holder
(R/L)
R
R
L
L
L
R
R
R
L
L
L
L
L
L
L
R
R
R
R
R
R
R
L
L
L
R
R
R
R
R
L
L
L
L
L
R
R
R
R
R
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
L
L
L
L
L
R
Ext.
00 F032
90 F044
Ext.
00 F032
90 F044
Ext.
00 F032
90 F044
Int.
Ext.
90 F096
00 F032
90 F044
Int.
Ext.
90 F096
00 F032
90 F044
Ext.
00 F032
90 F044
Ext.
00 F032
90 F044
Ext.
00 F032
90 F044
Ext.
00 F032
90 F044
Int.
Ext.
90 F096
00 F032
90 F044
Int.
Ext.
90 F096
00 F032
90 F044
Ext.
00 F032
90 F044
Order
Number
Hand
(R/L)
GYM20RA-F06
GYM20LA-F06
GYM20RA-F10
GYM20LA-F10
GYM20RB-F18
GYM20LB-F18
GYM25RA-F06
F
GYM25LA-F06
GYM25RA-F12
GYM25LA-F12
GYM25RA-F20
GYM25LA-F20
Modular holder
Order
Number
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHL2020K90-M20R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHR2020K90-M20L
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHL2020K90-M20R
GYDL32L90C-M20R
GYDL32S90C-M20R
GYDL40M90D-M20R
GYDL40T90D-M20R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHR2020K90-M20L
GYDR32L90C-M20L
GYDR32S90C-M20L
GYDR40M90D-M20L
GYDR40T90D-M20L
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHL2020K90-M20R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHR2020K90-M20L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYDL40M90D-M25R
GYDL40T90D-M25R
GYDL50P90F-M25R
GYDL50T90F-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
GYDR40M90D-M25L
GYDR40T90D-M25L
GYDR50P90F-M25L
GYDR50T90F-M25L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
Cutting Holder
(R/L)
R
R
L
L
L
R
R
R
L
L
L
L
L
L
L
R
R
R
R
R
R
R
L
L
L
R
R
R
R
R
L
L
L
L
L
R
R
R
R
R
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
L
L
L
L
L
R
Ext.
Seat
Size
Modular Blade
Modular holder
Order
Number
Order
Number
Hand
(R/L)
00 F034
90 F046
Ext.
GYM20RA-G12
00 F034
90 F046
Ext.
00 F034
90 F046
Int.
Ext.
GYM20LA-G12
90 F098
00 F034
90 F046
GYM25RA-G08
Int.
Ext.
90 F098
00 F034
GYM25LA-G08
90 F046
Ext.
00 F034
90 F046
Ext.
00 F034
G
GYM25RA-G14
90 F046
Ext.
00 F034
90 F046
Ext.
00 F034
GYM25LA-G14
90 F046
Int.
90 F098
GYM25RA-G25
Ext.
00 F034
90 F046
Int.
Ext.
90 F098
GYM25LA-G25
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHL2020K90-M20R
GYDL32L90C-M20R
GYDL32S90C-M20R
GYDL40M90D-M20R
GYDL40T90D-M20R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHR2020K90-M20L
GYDR32L90C-M20L
GYDR32S90C-M20L
GYDR40M90D-M20L
GYDR40T90D-M20L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYDL40M90D-M25R
GYDL40T90D-M25R
GYDL50P90F-M25R
GYDL50T90F-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
GYDR40M90D-M25L
GYDR40T90D-M25L
GYDR50P90F-M25L
GYDR50T90F-M25L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
Cutting Holder
(R/L)
R
R
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
L
L
L
L
L
R
R
R
R
R
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
L
L
L
L
L
R
Ext.
00 F036
90 F046
Int.
Ext.
90 F098
00 F036
90 F046
Int.
Ext.
90 F098
00 F036
GROOVING
Modular Blade
Seat
Size
90 F046
Ext.
00 F036
90 F046
Ext.
00 F036
90 F046
Int.
Ext.
90 F098
00 F036
90 F046
Int.
Ext.
90 F098
00 F036
90 F046
Ext.
00 F036
90 F046
00 F034
90 F046
Ext.
00 F034
90 F046
F017
EXTERNAL GROOVING / INTERNAL GROOVINGFACE / GROOVING
QUICK INDEX
List for selecting modular holder from modular blade
(For External and Internal Grooving)
Modular Blade
Seat
Size
Order
Number
GYM20RA-H12
GROOVING
GYM20LA-H12
Hand
(R/L)
GYM25RA-H08
GYM25LA-H08
H
GYM25RA-H14
GYM25LA-H14
GYM25RA-H25
GYM25LA-H25
F018
Modular holder
Order
Number
GYHR1616J00-M20R
GYHR2020K00-M20R
GYHL2020K90-M20R
GYDL32L90C-M20R
GYDL32S90C-M20R
GYDL40M90D-M20R
GYDL40T90D-M20R
GYHL1616J00-M20L
GYHL2020K00-M20L
GYHR2020K90-M20L
GYDR32L90C-M20L
GYDR32S90C-M20L
GYDR40M90D-M20L
GYDR40T90D-M20L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYDL40M90D-M25R
GYDL40T90D-M25R
GYDL50P90F-M25R
GYDL50T90F-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
GYDR40M90D-M25L
GYDR40T90D-M25L
GYDR50P90F-M25L
GYDR50T90F-M25L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
Cutting Holder
(R/L)
R
R
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
L
L
L
L
L
R
R
R
R
R
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
L
L
L
L
L
R
Ext.
Seat
Size
Ext.
Modular holder
Order
Number
Order
Number
Hand
(R/L)
00 F038
90 F048
Int.
Modular Blade
GYM25RA-J08
90 F100
GYM25LA-J08
00 F038
90 F048
Int.
90 F100
GYM25RA-J14
Ext.
00 F038
90 F048
Ext.
00 F038
90 F048
Ext.
GYM25LA-J14
00 F038
90 F048
Int.
Ext.
90 F100
00 F038
90 F048
Int.
Ext.
90 F100
00 F038
90 F048
Ext.
00 F038
90 F048
GYM25RA-J25
GYM25LA-J25
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYDL40M90D-M25R
GYDL40T90D-M25R
GYDL50P90F-M25R
GYDL50T90F-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
GYDR40M90D-M25L
GYDR40T90D-M25L
GYDR50P90F-M25L
GYDR50T90F-M25L
GYHR2020K00-M25R
GYHR2525M00-M25R
GYHR3225P00-M25R
GYHR3232P00-M25R
GYHL2525M90-M25R
GYHL2020K00-M25L
GYHL2525M00-M25L
GYHL3225P00-M25L
GYHL3232P00-M25L
GYHR2525M90-M25L
Cutting Holder
(R/L)
R
R
R
R
L
L
L
L
L
R
R
R
R
R
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
L
L
L
L
L
R
Ext.
00 F040
90 F048
Ext.
00 F040
90 F048
Ext.
00 F040
90 F048
Int.
Ext.
90 F100
00 F040
90 F048
Int.
Ext.
90 F100
00 F040
90 F048
Ext.
00 F040
90 F048
List for selecting modular blade set at modular holder

(For External and Face Grooving)
E
GYHR1616J00-M20R
Ext. 00
F
G
H
D
E
GYHL1616J00-M20L
Ext. 00
F
G
H
D
E
GYHR2020K00-M20R
Ext. 00
F
G
H
D
E
GYHL2020K00-M20L
Ext. 00
F
G
H
D
F
GYHR2020K00-M25R
Ext. 00
G
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM20RA-E06
GYM20RA-E10
GYM20RB-E18
GYM20RA-F06
GYM20RA-F10
GYM20RB-F18
GYM20RA-G12
GYM20RA-H12
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM20LA-E06
GYM20LA-E10
GYM20LB-E18
GYM20LA-F06
GYM20LA-F10
GYM20LB-F18
GYM20LA-G12
GYM20LA-H12
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM20RA-E06
GYM20RA-E10
GYM20RB-E18
GYM20RA-F06
GYM20RA-F10
GYM20RB-F18
GYM20RA-G12
GYM20RA-H12
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM20LA-E06
GYM20LA-E10
GYM20LB-E18
GYM20LA-F06
GYM20LA-F10
GYM20LB-F18
GYM20LA-G12
GYM20LA-H12
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
Modular Blade
Modular holder
Cutting Holder Seat

Hand Mode angle Size
Hand Page
Order Number
Order Number
(R/L)
(R/L)
R
R
R
R
R
R
R
R
R
R
R
L
L
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
R
R
L
L
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
F030
D
F032
F034
F036
F038
F030
F032
F034
F036
F038
F030
F032
F034
GYHR2020K00-M25R
Face 00
F036
F038
F030
F032
F034
F036
F038
F030
H
F032
F034
F036
J
F038
F040
GYM25RD-D12-040
GYM25RD-D12-050
GYM25RD-D12-060
GYM25RD-D12-075
GYM25RD-D12-100
GYM25RD-D12-135
GYM25RD-D12-180
GYM25RD-E12-040
GYM25RD-E12-050
GYM25RD-E12-060
GYM25RD-E12-075
GYM25RD-E12-100
GYM25RD-E12-135
GYM25RD-E12-180
GYM25RD-F12-035
GYM25RD-F12-040
GYM25RD-F12-050
GYM25RD-F12-060
GYM25RD-F12-075
GYM25RD-F20-060
GYM25RD-F20-075
GYM25RD-F12-100
GYM25RD-F12-135
GYM25RD-F20-100
GYM25RD-F20-135
GYM25RD-F12-180
GYM25RD-F12-225
GYM25RD-F20-180
GYM25RD-F20-225
GYM25RD-G14-040
GYM25RD-G14-050
GYM25RD-G14-060
GYM25RD-G25-060
GYM25RD-G14-085
GYM25RD-G14-125
GYM25RD-G25-085
GYM25RD-G25-125
GYM25RD-G14-180
GYM25RD-G14-250
GYM25RD-G25-180
GYM25RD-G25-250
GYM25RD-H14-050
GYM25RD-H14-060
GYM25RD-H25-060
GYM25RD-H14-085
GYM25RD-H14-125
GYM25RD-H25-085
GYM25RD-H25-125
GYM25RD-H14-180
GYM25RD-H14-250
GYM25RD-H25-180
GYM25RD-H25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J14-110
GYM25RD-J25-070
GYM25RD-J25-110
GYM25RD-J14-170
GYM25RD-J14-250
GYM25RD-J25-170
GYM25RD-J25-250
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
F052
F054
F056
F058
F060
GROOVING
Modular Blade
Modular holder
F062
F064
F066
F068
F070
F072
F074
F076
F078
F080
F082
F019
EXTERNAL GROOVING / GROOVING
QUICK INDEX
Modular Blade
Modular holder
Modular holder
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
D
F
Ext. 00
GROOVING
E
GYHL2020K00-M25L
Face 00
F
F020
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LD-D12-040
GYM25LD-D12-050
GYM25LD-D12-060
GYM25LD-D12-075
GYM25LD-D12-100
GYM25LD-D12-135
GYM25LD-D12-180
GYM25LD-E12-040
GYM25LD-E12-050
GYM25LD-E12-060
GYM25LD-E12-075
GYM25LD-E12-100
GYM25LD-E12-135
GYM25LD-E12-180
GYM25LD-F12-035
GYM25LD-F12-040
GYM25LD-F12-050
GYM25LD-F12-060
GYM25LD-F12-075
GYM25LD-F12-100
GYM25LD-F12-135
GYM25LD-F12-180
GYM25LD-F12-225
GYM25LD-F20-060
GYM25LD-F20-075
GYM25LD-F20-100
GYM25LD-F20-135
GYM25LD-F20-180
GYM25LD-F20-225
GYM25LD-G14-040
GYM25LD-G14-050
GYM25LD-G14-060
GYM25LD-G14-085
GYM25LD-G14-125
GYM25LD-G14-180
GYM25LD-G14-250
GYM25LD-G25-060
GYM25LD-G25-085
GYM25LD-G25-125
GYM25LD-G25-180
GYM25LD-G25-250
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Modular Blade
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
F030
F032
H
F034
F036
GYHL2020K00-M25L
Face 00
F038
J
F040
F052
GYHR2020K50-M20L
GYHL2020K50-M20R
F054
F056
D
E
Ext. Recessing F
G
H
D
E
Ext. Recessing F
G
H
F058
D
F060
E
F062
GYHR2020K90-M20L
Ext. 90
F
F064
G
H
F066
F062
F064
F066
E
GYHL2020K90-M20R
Ext. 90
F068
F070
G
H
F072
F068
F070
F072
GYM25LD-H14-050
GYM25LD-H14-060
GYM25LD-H14-085
GYM25LD-H14-125
GYM25LD-H14-180
GYM25LD-H14-250
GYM25LD-H25-060
GYM25LD-H25-085
GYM25LD-H25-125
GYM25LD-H25-180
GYM25LD-H25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J14-110
GYM25LD-J14-170
GYM25LD-J14-250
GYM25LD-J25-070
GYM25LD-J25-110
GYM25LD-J25-170
GYM25LD-J25-250
GYM20LC-D005
GYM20LC-E005
GYM20LC-F005
GYM20LC-G005
GYM20LC-H005
GYM20RC-D005
GYM20RC-E005
GYM20RC-F005
GYM20RC-G005
GYM20RC-H005
GYM20LA-D06
GYM20LA-D10
GYM20LB-D18
GYM20LA-E06
GYM20LA-E10
GYM20LB-E18
GYM20LA-F06
GYM20LA-F10
GYM20LB-F18
GYM20LA-G12
GYM20LA-H12
GYM20RA-D06
GYM20RA-D10
GYM20RB-D18
GYM20RA-E06
GYM20RA-E10
GYM20RB-E18
GYM20RA-F06
GYM20RA-F10
GYM20RB-F18
GYM20RA-G12
GYM20RA-H12
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
R
R
R
R
R
L
L
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
R
R
F074
F076
F078
F074
F076
F078
F080
F082
F080
F082
F050
F050
F044
F046
F048
F044
F046
F048
Modular holder
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
D
F
Ext. 00
G
E
GYHR2525M00-M25R R
Face 00
F
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RD-D12-040
GYM25RD-D12-050
GYM25RD-D12-060
GYM25RD-D12-075
GYM25RD-D12-100
GYM25RD-D12-135
GYM25RD-D12-180
GYM25RD-E12-040
GYM25RD-E12-050
GYM25RD-E12-060
GYM25RD-E12-075
GYM25RD-E12-100
GYM25RD-E12-135
GYM25RD-E12-180
GYM25RD-F12-035
GYM25RD-F12-040
GYM25RD-F12-050
GYM25RD-F12-060
GYM25RD-F12-075
GYM25RD-F12-100
GYM25RD-F12-135
GYM25RD-F12-180
GYM25RD-F12-225
GYM25RD-F20-060
GYM25RD-F20-075
GYM25RD-F20-100
GYM25RD-F20-135
GYM25RD-F20-180
GYM25RD-F20-225
GYM25RD-G14-040
GYM25RD-G14-050
GYM25RD-G14-060
GYM25RD-G14-085
GYM25RD-G14-125
GYM25RD-G14-180
GYM25RD-G14-250
GYM25RD-G25-060
GYM25RD-G25-085
GYM25RD-G25-125
GYM25RD-G25-180
GYM25RD-G25-250
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Modular Blade
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
F030
F032
H
F034
F036
GYHR2525M00-M25R R
Face 00
F038
J
F040
F052
D
F054
E
F056
F
Ext. 00
F058
F060
F062
GYHL2525M00-M25L
F064
F066
D
F062
F064
Face 00
F066
F068
F070
GYM25RD-H14-050
GYM25RD-H14-060
GYM25RD-H14-085
GYM25RD-H14-125
GYM25RD-H14-180
GYM25RD-H14-250
GYM25RD-H25-060
GYM25RD-H25-085
GYM25RD-H25-125
GYM25RD-H25-180
GYM25RD-H25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J14-110
GYM25RD-J14-170
GYM25RD-J14-250
GYM25RD-J25-070
GYM25RD-J25-110
GYM25RD-J25-170
GYM25RD-J25-250
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LD-D12-040
GYM25LD-D12-050
GYM25LD-D12-060
GYM25LD-D12-075
GYM25LD-D12-100
GYM25LD-D12-135
GYM25LD-D12-180
GYM25LD-E12-040
GYM25LD-E12-050
GYM25LD-E12-060
GYM25LD-E12-075
GYM25LD-E12-100
GYM25LD-E12-135
GYM25LD-E12-180
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
F074
F076
F078
F074
F076
F078
F080
F082
GROOVING
Modular Blade
Modular holder
F080
F082
F030
F032
F034
F036
F038
F040
F052
F054
F056
F058
F072
F068
F070
F072
F021
QUICK INDEX
Modular Blade
Modular holder
GROOVING
G
GYHL2525M00-M25L
Face 00
GYHR2525M50-M25L
GYHL2525M50-M25R
F022
D
E
F
Ext. Recessing
G
H
J
D
E
F
Ext. Recessing
G
H
J
GYM25LD-F12-035
GYM25LD-F12-040
GYM25LD-F12-050
GYM25LD-F12-060
GYM25LD-F12-075
GYM25LD-F12-100
GYM25LD-F12-135
GYM25LD-F12-180
GYM25LD-F12-225
GYM25LD-F20-060
GYM25LD-F20-075
GYM25LD-F20-100
GYM25LD-F20-135
GYM25LD-F20-180
GYM25LD-F20-225
GYM25LD-G14-040
GYM25LD-G14-050
GYM25LD-G14-060
GYM25LD-G14-085
GYM25LD-G14-125
GYM25LD-G14-180
GYM25LD-G14-250
GYM25LD-G25-060
GYM25LD-G25-085
GYM25LD-G25-125
GYM25LD-G25-180
GYM25LD-G25-250
GYM25LD-H14-050
GYM25LD-H14-060
GYM25LD-H14-085
GYM25LD-H14-125
GYM25LD-H14-180
GYM25LD-H14-250
GYM25LD-H25-060
GYM25LD-H25-085
GYM25LD-H25-125
GYM25LD-H25-180
GYM25LD-H25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J14-110
GYM25LD-J14-170
GYM25LD-J14-250
GYM25LD-J25-070
GYM25LD-J25-110
GYM25LD-J25-170
GYM25LD-J25-250
GYM25LC-D005
GYM25LC-E005
GYM25LC-F005
GYM25LC-G005
GYM25LC-H005
GYM25LC-J005
GYM25RC-D005
GYM25RC-E005
GYM25RC-F005
GYM25RC-G005
GYM25RC-H005
GYM25RC-J005
Modular Blade
Modular holder
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
D
F060
F062
F064
F
F066
GYHR2525M90-M25L
Ext. 90
F062
F064
H
F066
F068
F070
F072
F068
F070
F072
F074
F076
F078
F074
F076
F078
GYHR2525M90-M25L
F080
Face 90
F
F082
F080
F082
F050
F050
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LD-D12-040
GYM25LD-D12-050
GYM25LD-D12-060
GYM25LD-D12-075
GYM25LD-D12-100
GYM25LD-D12-135
GYM25LD-D12-180
GYM25LD-E12-040
GYM25LD-E12-050
GYM25LD-E12-060
GYM25LD-E12-075
GYM25LD-E12-100
GYM25LD-E12-135
GYM25LD-E12-180
GYM25LD-F12-035
GYM25LD-F12-040
GYM25LD-F12-050
GYM25LD-F12-060
GYM25LD-F12-075
GYM25LD-F12-100
GYM25LD-F12-135
GYM25LD-F12-180
GYM25LD-F12-225
GYM25LD-F20-060
GYM25LD-F20-075
GYM25LD-F20-100
GYM25LD-F20-135
GYM25LD-F20-180
GYM25LD-F20-225
GYM25LD-G14-040
GYM25LD-G14-050
GYM25LD-G14-060
GYM25LD-G14-085
GYM25LD-G14-125
GYM25LD-G14-180
GYM25LD-G14-250
GYM25LD-G25-060
GYM25LD-G25-085
GYM25LD-G25-125
GYM25LD-G25-180
GYM25LD-G25-250
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
F044
F044
F046
F046
F048
F048
F084
F084
F086
F088
Modular holder
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
GYHR2525M90-M25L
Face 90
F
Ext. 90
G
H
GYHL2525M90-M25R
Face 90
GYM25LD-H14-050
GYM25LD-H14-060
GYM25LD-H14-085
GYM25LD-H14-125
GYM25LD-H14-180
GYM25LD-H14-250
GYM25LD-H25-060
GYM25LD-H25-085
GYM25LD-H25-125
GYM25LD-H25-180
GYM25LD-H25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J14-110
GYM25LD-J14-170
GYM25LD-J14-250
GYM25LD-J25-070
GYM25LD-J25-110
GYM25LD-J25-170
GYM25LD-J25-250
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RD-D12-040
GYM25RD-D12-050
GYM25RD-D12-060
GYM25RD-D12-075
GYM25RD-D12-100
GYM25RD-D12-135
GYM25RD-D12-180
GYM25RD-E12-040
GYM25RD-E12-050
GYM25RD-E12-060
GYM25RD-E12-075
GYM25RD-E12-100
GYM25RD-E12-135
GYM25RD-E12-180
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Modular Blade
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
F090
F
F092
F044
GYHL2525M90-M25R
Face 90
F044
F046
F046
H
F048
F048
F084
J
F084
GYHR3225P00-M25R
Ext. 00
GYM25RD-F12-035
GYM25RD-F12-040
GYM25RD-F12-050
GYM25RD-F12-060
GYM25RD-F12-075
GYM25RD-F12-100
GYM25RD-F12-135
GYM25RD-F12-180
GYM25RD-F12-225
GYM25RD-F20-060
GYM25RD-F20-075
GYM25RD-F20-100
GYM25RD-F20-135
GYM25RD-F20-180
GYM25RD-F20-225
GYM25RD-G14-040
GYM25RD-G14-050
GYM25RD-G14-060
GYM25RD-G14-085
GYM25RD-G14-125
GYM25RD-G14-180
GYM25RD-G14-250
GYM25RD-G25-060
GYM25RD-G25-085
GYM25RD-G25-125
GYM25RD-G25-180
GYM25RD-G25-250
GYM25RD-H14-050
GYM25RD-H14-060
GYM25RD-H14-085
GYM25RD-H14-125
GYM25RD-H14-180
GYM25RD-H14-250
GYM25RD-H25-060
GYM25RD-H25-085
GYM25RD-H25-125
GYM25RD-H25-180
GYM25RD-H25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J14-110
GYM25RD-J14-170
GYM25RD-J14-250
GYM25RD-J25-070
GYM25RD-J25-110
GYM25RD-J25-170
GYM25RD-J25-250
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
F086
GROOVING
Modular Blade
Modular holder
F088
F090
F092
F030
F032
F034
F036
F038
F023
QUICK INDEX
Modular Blade
Modular holder
Modular holder
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
Ext. 00
GROOVING
GYHR3225P00-M25R
R
Face 00
F024
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RD-D12-040
GYM25RD-D12-050
GYM25RD-D12-060
GYM25RD-D12-075
GYM25RD-D12-100
GYM25RD-D12-135
GYM25RD-D12-180
GYM25RD-E12-040
GYM25RD-E12-050
GYM25RD-E12-060
GYM25RD-E12-075
GYM25RD-E12-100
GYM25RD-E12-135
GYM25RD-E12-180
GYM25RD-F12-035
GYM25RD-F12-040
GYM25RD-F12-050
GYM25RD-F12-060
GYM25RD-F12-075
GYM25RD-F12-100
GYM25RD-F12-135
GYM25RD-F12-180
GYM25RD-F12-225
GYM25RD-F20-060
GYM25RD-F20-075
GYM25RD-F20-100
GYM25RD-F20-135
GYM25RD-F20-180
GYM25RD-F20-225
GYM25RD-G14-040
GYM25RD-G14-050
GYM25RD-G14-060
GYM25RD-G14-085
GYM25RD-G14-125
GYM25RD-G14-180
GYM25RD-G14-250
GYM25RD-G25-060
GYM25RD-G25-085
GYM25RD-G25-125
GYM25RD-G25-180
GYM25RD-G25-250
GYM25RD-H14-050
GYM25RD-H14-060
GYM25RD-H14-085
GYM25RD-H14-125
GYM25RD-H14-180
GYM25RD-H14-250
GYM25RD-H25-060
GYM25RD-H25-085
GYM25RD-H25-125
GYM25RD-H25-180
GYM25RD-H25-250
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Modular Blade
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
F040
F052
GYHR3225P00-M25R
Face 00
F054
D
F056
E
F058
F
Ext. 00
F060
G
F062
H
F064
F066
F062
F064
D
F066
GYHL3225P00-M25L
F068
F070
E
F072
F068
F070
Face 00
F072
F074
F076
F078
F074
F076
F078
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J14-110
GYM25RD-J14-170
GYM25RD-J14-250
GYM25RD-J25-070
GYM25RD-J25-110
GYM25RD-J25-170
GYM25RD-J25-250
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LD-D12-040
GYM25LD-D12-050
GYM25LD-D12-060
GYM25LD-D12-075
GYM25LD-D12-100
GYM25LD-D12-135
GYM25LD-D12-180
GYM25LD-E12-040
GYM25LD-E12-050
GYM25LD-E12-060
GYM25LD-E12-075
GYM25LD-E12-100
GYM25LD-E12-135
GYM25LD-E12-180
GYM25LD-F12-035
GYM25LD-F12-040
GYM25LD-F12-050
GYM25LD-F12-060
GYM25LD-F12-075
GYM25LD-F12-100
GYM25LD-F12-135
GYM25LD-F12-180
GYM25LD-F12-225
GYM25LD-F20-060
GYM25LD-F20-075
GYM25LD-F20-100
GYM25LD-F20-135
GYM25LD-F20-180
GYM25LD-F20-225
R
R
R
R
R
R
R
R
R
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
F080
F082
F080
F082
F030
F032
F034
F036
F038
F040
F052
F054
F056
F058
F060
F062
F064
F066
F062
F064
F066
Modular holder
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
GYHL3225P00-M25L
Face 00
H
F
Ext. 00
G
GYHR3232P00-M25R
R
H
Face 00
GYM25LD-G14-040
GYM25LD-G14-050
GYM25LD-G14-060
GYM25LD-G14-085
GYM25LD-G14-125
GYM25LD-G14-180
GYM25LD-G14-250
GYM25LD-G25-060
GYM25LD-G25-085
GYM25LD-G25-125
GYM25LD-G25-180
GYM25LD-G25-250
GYM25LD-H14-050
GYM25LD-H14-060
GYM25LD-H14-085
GYM25LD-H14-125
GYM25LD-H14-180
GYM25LD-H14-250
GYM25LD-H25-060
GYM25LD-H25-085
GYM25LD-H25-125
GYM25LD-H25-180
GYM25LD-H25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J14-110
GYM25LD-J14-170
GYM25LD-J14-250
GYM25LD-J25-070
GYM25LD-J25-110
GYM25LD-J25-170
GYM25LD-J25-250
GYM25RA-D06
GYM25RA-D12
GYM25RA-D20
GYM25RA-E06
GYM25RA-E12
GYM25RA-E20
GYM25RA-F06
GYM25RA-F12
GYM25RA-F20
GYM25RA-G08
GYM25RA-G14
GYM25RA-G25
GYM25RA-H08
GYM25RA-H14
GYM25RA-H25
GYM25RA-J08
GYM25RA-J14
GYM25RA-J25
GYM25RD-D12-040
GYM25RD-D12-050
GYM25RD-D12-060
GYM25RD-D12-075
GYM25RD-D12-100
GYM25RD-D12-135
GYM25RD-D12-180
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Modular Blade
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
F068
E
F070
F072
F068
F070
F072
F074
F076
F078
F074
F076
F078
F080
F082
GYHR3232P00-M25R
Face 00
G
F080
F082
F030
F032
F034
F036
F038
F040
J
F052
GYM25RD-E12-040
GYM25RD-E12-050
GYM25RD-E12-060
GYM25RD-E12-075
GYM25RD-E12-100
GYM25RD-E12-135
GYM25RD-E12-180
GYM25RD-F12-035
GYM25RD-F12-040
GYM25RD-F12-050
GYM25RD-F12-060
GYM25RD-F12-075
GYM25RD-F12-100
GYM25RD-F12-135
GYM25RD-F12-180
GYM25RD-F12-225
GYM25RD-F20-060
GYM25RD-F20-075
GYM25RD-F20-100
GYM25RD-F20-135
GYM25RD-F20-180
GYM25RD-F20-225
GYM25RD-G14-040
GYM25RD-G14-050
GYM25RD-G14-060
GYM25RD-G14-085
GYM25RD-G14-125
GYM25RD-G14-180
GYM25RD-G14-250
GYM25RD-G25-060
GYM25RD-G25-085
GYM25RD-G25-125
GYM25RD-G25-180
GYM25RD-G25-250
GYM25RD-H14-050
GYM25RD-H14-060
GYM25RD-H14-085
GYM25RD-H14-125
GYM25RD-H14-180
GYM25RD-H14-250
GYM25RD-H25-060
GYM25RD-H25-085
GYM25RD-H25-125
GYM25RD-H25-180
GYM25RD-H25-250
GYM25RD-J14-050
GYM25RD-J14-070
GYM25RD-J14-110
GYM25RD-J14-170
GYM25RD-J14-250
GYM25RD-J25-070
GYM25RD-J25-110
GYM25RD-J25-170
GYM25RD-J25-250
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
F056
F058
F060
F062
F064
F066
GROOVING
Modular Blade
Modular holder
F062
F064
F066
F068
F070
F072
F068
F070
F072
F074
F076
F078
F074
F076
F078
F080
F082
F080
F082
F054
F025
EXTERNAL GROOVING / GROOVING / INTERNAL GROOVINGFACE
QUICK INDEX
Modular holder
Modular Blade
Modular holder
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
D
F
Ext. 00
GROOVING
E
GYHL3232P00-M25L
Face 00
F
F026
GYM25LA-D06
GYM25LA-D12
GYM25LA-D20
GYM25LA-E06
GYM25LA-E12
GYM25LA-E20
GYM25LA-F06
GYM25LA-F12
GYM25LA-F20
GYM25LA-G08
GYM25LA-G14
GYM25LA-G25
GYM25LA-H08
GYM25LA-H14
GYM25LA-H25
GYM25LA-J08
GYM25LA-J14
GYM25LA-J25
GYM25LD-D12-040
GYM25LD-D12-050
GYM25LD-D12-060
GYM25LD-D12-075
GYM25LD-D12-100
GYM25LD-D12-135
GYM25LD-D12-180
GYM25LD-E12-040
GYM25LD-E12-050
GYM25LD-E12-060
GYM25LD-E12-075
GYM25LD-E12-100
GYM25LD-E12-135
GYM25LD-E12-180
GYM25LD-F12-035
GYM25LD-F12-040
GYM25LD-F12-050
GYM25LD-F12-060
GYM25LD-F12-075
GYM25LD-F12-100
GYM25LD-F12-135
GYM25LD-F12-180
GYM25LD-F12-225
GYM25LD-F20-060
GYM25LD-F20-075
GYM25LD-F20-100
GYM25LD-F20-135
GYM25LD-F20-180
GYM25LD-F20-225
GYM25LD-G14-040
GYM25LD-G14-050
GYM25LD-G14-060
GYM25LD-G14-085
GYM25LD-G14-125
GYM25LD-G14-180
GYM25LD-G14-250
GYM25LD-G25-060
GYM25LD-G25-085
GYM25LD-G25-125
GYM25LD-G25-180
GYM25LD-G25-250
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Modular Blade
Cutting Holder Seat

Hand Page
Order Number
Order Number
(R/L)
(R/L)
F030
F032
H
F034
F036
GYHL3232P00-M25L
Face 00
F038
J
F040
F052
F054
F056
F058
F060
F062
F064
F066
F062
F064
F066
F068
F070
F072
F068
F070
F072
GYM25LD-H14-050
GYM25LD-H14-060
GYM25LD-H14-085
GYM25LD-H14-125
GYM25LD-H14-180
GYM25LD-H14-250
GYM25LD-H25-060
GYM25LD-H25-085
GYM25LD-H25-125
GYM25LD-H25-180
GYM25LD-H25-250
GYM25LD-J14-050
GYM25LD-J14-070
GYM25LD-J14-110
GYM25LD-J14-170
GYM25LD-J14-250
GYM25LD-J25-070
GYM25LD-J25-110
GYM25LD-J25-170
GYM25LD-J25-250
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
F074
F076
F078
F074
F076
F078
F080
F082
F080
F082

(For Internal Grooving)
GYDR32L90C-M20L
GYDL32L90C-M20R
GYDR32S90C-M20L
GYDL32S90C-M20R
GYDR40M90D-M20L
GYDL40M90D-M20R
GYDR40M90D-M25L
GYDL40M90D-M25R
GYDR40T90D-M20L
GYDL40T90D-M20R
GYDR40T90D-M25L
GYDL40T90D-M25R
Holder Seat
Hand angle Size
(R/L)
90
90
90
90
90
90
90
90
90
90
90
90
D
E
F
G
H
D
E
F
G
H
D
E
F
G
H
D
E
F
G
H
D
E
F
G
H
D
E
F
G
H
D
E
F
G
H
J
D
E
F
G
H
J
D
E
F
G
H
D
E
F
G
H
D
E
F
G
H
J
D
E
F
G
H
J
Order Number
GYM20LA-D10
GYM20LA-E10
GYM20LA-F10
GYM20LA-G12
GYM20LA-H12
GYM20RA-D10
GYM20RA-E10
GYM20RA-F10
GYM20RA-G12
GYM20RA-H12
GYM20LA-D10
GYM20LA-E10
GYM20LA-F10
GYM20LA-G12
GYM20LA-H12
GYM20RA-D10
GYM20RA-E10
GYM20RA-F10
GYM20RA-G12
GYM20RA-H12
GYM20LA-D10
GYM20LA-E10
GYM20LA-F10
GYM20LA-G12
GYM20LA-H12
GYM20RA-D10
GYM20RA-E10
GYM20RA-F10
GYM20RA-G12
GYM20RA-H12
GYM25LA-D12
GYM25LA-E12
GYM25LA-F12
GYM25LA-G14
GYM25LA-H14
GYM25LA-J14
GYM25RA-D12
GYM25RA-E12
GYM25RA-F12
GYM25RA-G14
GYM25RA-H14
GYM25RA-J14
GYM20LA-D10
GYM20LA-E10
GYM20LA-F10
GYM20LA-G12
GYM20LA-H12
GYM20RA-D10
GYM20RA-E10
GYM20RA-F10
GYM20RA-G12
GYM20RA-H12
GYM25LA-D12
GYM25LA-E12
GYM25LA-F12
GYM25LA-G14
GYM25LA-H14
GYM25LA-J14
GYM25RA-D12
GYM25RA-E12
GYM25RA-F12
GYM25RA-G14
GYM25RA-H14
GYM25RA-J14
Hand Page
(R/L)
L
L
L
L
L
R
R
R
R
R
L
L
L
L
L
R
R
R
R
R
L
L
L
L
L
R
R
R
R
R
L
L
L
L
L
L
R
R
R
R
R
R
L
L
L
L
L
R
R
R
R
R
L
L
L
L
L
L
R
R
R
R
R
R
Order Number
Modular Blade
Holder Seat
Hand angle Size
(R/L)
F094
F096
F098
GYDR50P90F-M25L
90
F100
F094
F096
F098
F100
F094
F096
GYDL50P90F-M25R
90
F098
F100
F094
F096
GYDR50T90F-M25L
90
F098
F100
F094
F096
F098
GYDL50T90F-M25R
90
D
E
F
G
H
J
D
E
F
G
H
J
D
E
F
G
H
J
D
E
F
G
H
J
Order Number
GYM25LA-D12
GYM25LA-E12
GYM25LA-F12
GYM25LA-G14
GYM25LA-H14
GYM25LA-J14
GYM25RA-D12
GYM25RA-E12
GYM25RA-F12
GYM25RA-G14
GYM25RA-H14
GYM25RA-J14
GYM25LA-D12
GYM25LA-E12
GYM25LA-F12
GYM25LA-G14
GYM25LA-H14
GYM25LA-J14
GYM25RA-D12
GYM25RA-E12
GYM25RA-F12
GYM25RA-G14
GYM25RA-H14
GYM25RA-J14
Hand Page
(R/L)
L
L
L
L
L
L
R
R
R
R
R
R
L
L
L
L
L
L
R
R
R
R
R
R
F094
F096
F098
F100
F094
F096
F098
F100
F094
F096
F098
GROOVING
Order Number
Modular holder
Modular Blade
Modular holder
F100
F094
F096
F098
F100
F100
F094
F096
F098
F100
F094
F096
F098
F100
F094
F096
F098
F100
F094
F096
F098
F100
F094
F096
F098
F100
F094
F096
F098
F100
F094
F096
F098
F100
F027
EXTERNAL GROOVING
GYSERIES (External for Swiss style lathes)

CDX
B
00 type holder
0
CW
LF
LH
IA
TD

-GM
Fig. B
LH 2
LH
DIA
UT
Fig. C
LH
DIA
T
CU
HF
CU
HF
Fig. A
HBH
LH 2
HF
LH 2
GROOVING

Seat
Size
CW
1.50
*4
CDX
2.39
2.50
2.74
3.00
3.18
3.24
Type
11
22
Mono Block
13
26
Mono Block
*
18 1
*
34 2
*
36 2
*
Mono Block
11
22
Mono Block
13
26
Mono Block
17
34
Mono Block
18
36
Mono Block
11
22
Mono Block
13
26
Mono Block
17
34
Mono Block
18
36
Mono Block
11
22
Mono Block
13
26
Mono Block
17
34
Mono Block
18
36
Mono Block
17 1
2.00
2.24
CUTDIA
Mono Block
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
GYSR1010JX00-C11
GYSL1010JX00-C11
GYSR1212JX00-C13
GYSL1212JX00-C13
GYSR1616JX00-C17
GYSL1616JX00-C17
GYSR2012JX00-C18
GYSL2012JX00-C18
GYSR1010JX00-D11
GYSL1010JX00-D11
GYSR1212JX00-D13
GYSL1212JX00-D13
GYSR1616JX00-D17
GYSL1616JX00-D17
GYSR2012JX00-D18
GYSL2012JX00-D18
GYSR1010JX00-E11
GYSL1010JX00-E11
GYSR1212JX00-E13
GYSL1212JX00-E13
GYSR1616JX00-E17
GYSL1616JX00-E17
GYSR2012JX00-E18
GYSL2012JX00-E18
GYSR1010JX00-F11
GYSL1010JX00-F11
GYSR1212JX00-F13
GYSL1212JX00-F13
GYSR1616JX00-F17
GYSL1616JX00-F17
GYSR2012JX00-F18
GYSL2012JX00-F18
Stock
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
A
A
B
B
B
B
C
C
A
A
B
B
B
B
C
C
A
A
B
B
B
B
C
C
A
A
B
B
B
B
C
C
maximum groove depth varies according to the insert used. Please refer to the maximum groove depth of inserts on pages F012 F014.
*12 The
The maximum cut off diameter CUTDIA varies according to the insert used. The cut off diameter is double the maximum groove depth (CDX) of inserts on pages F012F014.
*3 Dimensions shown are when the gauge insert is used. If other insert geometries are used then LF, LH and LH 2 values may vary.
*4 The maximum groove depth is limited by the workpiece diameter. For details, please refer to page F104.
*
F028
SPARE PARTS
Holder
GYSR/L1010JX00-o11
GYSR/L1212JX00-o13
GYSR/L2012JX00-o18
GYSR/L1616JX00-o17
*3
Wrench
CS350990T
(Clamp Torque
: 2.5Nm)
TKY10R
TS4SBL
(Clamp Torque
: 3.5Nm)
TKY15R
Cutting Mode
LF
LH
LH 2
HF
HBH
10
10
12
12
16
16
20
20
10
10
12
12
16
16
20
20
10
10
12
12
16
16
20
20
10
10
12
12
16
16
20
20
10
10
12
12
16
16
12
12
10
10
12
12
16
16
12
12
10
10
12
12
16
16
12
12
10
10
12
12
16
16
12
12
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
22
22
22
22
27
27
28
28
22
22
22
22
27
27
28
28
22
22
22
22
27
27
28
28
22
22
22
22
27
27
28
28
16
16
16
16
17
17
16
16
23
23
23
23
24
24
23
23
23
23
23
23
24
24
23
23
23
23
23
23
24
24
23
23
10
10
12
12
16
16
20
20
10
10
12
12
16
16
20
20
10
10
12
12
16
16
20
20
10
10
12
12
16
16
20
20
2
2
2
2
2
2
2
2
Clockwise
Anticlockwise
GROOVING
Dimensions (mm)
Clamp Screw
Insert selection
Seat
Size
C
D
E
F
Geometry name
GYoo0150CooooBreaker shown below
GYoo0200/0224DooooBreaker shown below
GYoo0239/0250/0274EooooBreaker shown below
GYoo0300/0318/0324FooooBreaker shown below
For grooving/cutting off breaker

Seat
Size
C
D
E
F
Breaker
CW
1.50mm
2.00mm
2.39mm
2.50mm
3.00mm
3.18mm
Neutral Neutral Neutral With hand Neutral

a
Seat
Size
D
E
a
a
a
F013, F014
MF
MS
MM
BM
(Finish) (Low) (Medium) (Copying, Recessing)
CW
2.00mm
2.24mm
2.39mm
2.50mm
2.74mm
3.00mm
RE 0.2
RE 0.4
RE 0.8
3.18mm
RE 0.2
RE 0.4
3.24mm
a
a
For multifunctional grooving breaker

Breaker
F012, F013
GU
GS
GM 05-GM GFGS
(For gummy steel) (Low) (Medium) (Cutting off) (Hardened steel)
Ball shape
a
a
a
a
a
a
a
a
a
a
a
: Standard insert with dimensions
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F102
F104
F029
EXTERNAL GROOVING

CDX
B
00 type holder
WF
CW
LF
LH

-GM
HF
CU
TD
IA
Fig. B
HF
Fig. A
CU
TD
IA
LH
LH 2
LH
HF
CU
TD
IA
CU
TD
IA
Fig. F
HF
Fig. E
LH 2
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
CDX
CUTDIA
Type
Modular
Mono Block
Modular
Modular
6
12
Mono Block
Modular
Modular
Modular
Modular
10
20
Modular
Modular
2.00
2.24
Modular
12
24
Modular
Modular
Modular
18 4
Mono Block
36
Modular
Modular
Mono Block
20 1
40 2
Modular
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
GYHR1616J00-M20R
GYHL1616J00-M20L
GYQR2020K00-D06
GYQL2020K00-D06
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYQR2525M00-D06
GYQL2525M00-D06
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR1616J00-M20R
GYHL1616J00-M20L
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR1616J00-M20R
GYHL1616J00-M20L
GYQR2020K00-D18
GYQL2020K00-D18
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYQR2525M00-D20
GYQL2525M00-D20
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Modular Blade
GYM20RA-D06
GYM20LA-D06
GYM20RA-D06
GYM20LA-D06
GYM25RA-D06
GYM25LA-D06
GYM25RA-D06
GYM25LA-D06
GYM25RA-D06
GYM25LA-D06
GYM25RA-D06
GYM25LA-D06
GYM20RA-D10
GYM20LA-D10
GYM20RA-D10
GYM20LA-D10
GYM25RA-D12
GYM25LA-D12
GYM25RA-D12
GYM25LA-D12
GYM25RA-D12
GYM25LA-D12
GYM25RA-D12
GYM25LA-D12
GYM20RB-D18
GYM20LB-D18
GYM20RB-D18
GYM20LB-D18
GYM25RA-D20
GYM25LA-D20
GYM25RA-D20
GYM25LA-D20
GYM25RA-D20
GYM25LA-D20
GYM25RA-D20
GYM25LA-D20
Stock
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
G
G
A
A
C
C
G
G
A
A
E
E
E
E
C
C
A
A
C
C
A
A
E
E
E
E
D
D
G
G
B
B
D
D
G
G
B
B
F
F
F
F
*12 The
The maximum cut off diameter CUTDIA varies according to the insert used. The cut off diameter is double the maximum groove depth (CDX) of inserts on pages F012 F014.
*3 Dimensions shown are when the gauge insert is used. If other insert geometries are used then LF, LH, LH 2 and WF values may vary.
*
a
F030
* Wrench : z : Clamp Screw, x : Blade Screw
SPARE PARTS
WF
CW
CDX
Holder
LF
Clamp Screw Blade Screw
IA
HSC05030
GYQR/Looooooo-ooo (Clamp Torque
: 7.0Nm)
HBH
HBH
HF
CU
TD
TD
CU
HF
Fig. G
LH 2
LH
LH 2
TD
GYHR/Looooooo-M20R/L
H
HF
CU
GY06013M
(Clamp Torque
: 6.0Nm)
*3
Dimensions (mm)
5 pcs.
IA
Fig. D
IA
Fig. C
LH
Wrench
HKY40R
TS407
(Clamp Torque
: 3.5Nm)
zTKY30R
xTKY15D
TS55
(Clamp Torque
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
16
16
20
20
20
20
20
20
25
25
25
25
32
32
32
32
16
16
20
20
20
20
25
25
32
32
32
32
16
16
20
20
20
20
20
20
25
25
25
25
32
32
32
32
16
16
20
20
20
20
20
20
25
25
25
25
25
25
32
32
16
16
20
20
20
20
25
25
25
25
32
32
16
16
20
20
20
20
20
20
25
25
25
25
25
25
32
32
104
104
125
125
119
119
117
117
150
150
142
142
162
162
162
162
110
110
125
125
125
125
150
150
170
170
170
170
116
116
125
125
131
131
131
131
150
150
156
156
176
176
176
176
28
28
36
36
28
28
31
31
36
36
31
31
31
31
31
31
34
34
34
34
39
39
39
39
39
39
39
39
40
40
39
39
40
40
45
45
41
41
45
45
45
45
45
45
44
44
43
43
52
52
49
49
49
49
49
49
50
50
49
49
60
60
57
57
57
57
57
57
56
56
55
55
66
66
63
63
63
63
63
63
16
16
20
20
20
20
20
20
25
25
25
25
32
32
32
32
16
16
20
20
20
20
25
25
32
32
32
32
16
16
20
20
20
20
20
20
25
25
25
25
32
32
32
32
20
20
20.15
20.15
23
23
26
26
25.15
25.15
28
28
28
28
35
35
20
20
23
23
26
26
28
28
28
28
35
35
20
20
20.1
20.1
23
23
26
26
25.1
25.1
28
28
28
28
35
35
4
4
5
5
4
4
5
5
4
4
5
5
Clockwise
Anticlockwise
GROOVING
LH
Insert selection
Seat
Size
D
Geometry name

Seat
Size
D
Breaker
CW
2.00mm

a

Seat
Size
D
a
Breaker
F013, F014
MF
MS
MM
BM
CW
2.00mm
2.24mm
F012, F013
GU
GS
GM 05-GM GFGS
Ball shape
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F102
F106
F031
EXTERNAL GROOVING

CDX
B
00 type holder
WF
CW
LF
LH

-GM
HF
CU
TD
IA
Fig. B
HF
Fig. A
CU
TD
IA
LH
LH 2
CU
TD
IA
HF
Fig. F
HF
Fig. E
LH 2
LH
CU
TD
IA
LH 2
LH
LH 2
GROOVING

Seat
Size
CW
CDX
CUTDIA
Type
Modular
Modular
Modular
6
12
Modular
Modular
Modular
Modular
10
20
Modular
2.39
2.50
2.74
Modular
Modular
12
24
Modular
Modular
Modular
18 4
36
Modular
Modular
Modular
20 1
40 2
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR1616J00-M20R
GYHL1616J00-M20L
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR1616J00-M20R
GYHL1616J00-M20L
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR1616J00-M20R
GYHL1616J00-M20L
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM20RA-E06
GYM20LA-E06
GYM20RA-E06
GYM20LA-E06
GYM25RA-E06
GYM25LA-E06
GYM25RA-E06
GYM25LA-E06
GYM25RA-E06
GYM25LA-E06
GYM25RA-E06
GYM25LA-E06
GYM20RA-E10
GYM20LA-E10
GYM20RA-E10
GYM20LA-E10
GYM25RA-E12
GYM25LA-E12
GYM25RA-E12
GYM25LA-E12
GYM25RA-E12
GYM25LA-E12
GYM25RA-E12
GYM25LA-E12
GYM20RB-E18
GYM20LB-E18
GYM20RB-E18
GYM20LB-E18
GYM25RA-E20
GYM25LA-E20
GYM25RA-E20
GYM25LA-E20
GYM25RA-E20
GYM25LA-E20
GYM25RA-E20
GYM25LA-E20
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
A
A
C
C
A
A
E
E
E
E
C
C
A
A
C
C
A
A
E
E
E
E
D
D
B
B
D
D
B
B
F
F
F
F
*12 The
*
F032
SPARE PARTS
WF
CW
CDX
Holder
LF
CU
TD
IA
H
HBH
GY06013M
(Clamp Torque
: 6.0Nm)
*3
Wrench
HKY40R
TS407
(Clamp Torque
: 3.5Nm)
zTKY30R
xTKY15D
TS55
(Clamp Torque
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
16
16
20
20
20
20
25
25
32
32
32
32
16
16
20
20
20
20
25
25
32
32
32
32
16
16
20
20
20
20
25
25
32
32
32
32
16
16
20
20
20
20
25
25
25
25
32
32
16
16
20
20
20
20
25
25
25
25
32
32
16
16
20
20
20
20
25
25
25
25
32
32
104
104
119
119
117
117
142
142
162
162
162
162
110
110
125
125
125
125
150
150
170
170
170
170
116
116
131
131
131
131
156
156
176
176
176
176
28
28
28
28
31
31
31
31
31
31
31
31
34
34
34
34
39
39
39
39
39
39
39
39
40
40
40
40
45
45
45
45
45
45
45
45
44
44
43
43
52
52
49
49
49
49
49
49
50
50
49
49
60
60
57
57
57
57
57
57
56
56
55
55
66
66
63
63
63
63
63
63
16
16
20
20
20
20
25
25
32
32
32
32
16
16
20
20
20
20
25
25
32
32
32
32
16
16
20
20
20
20
25
25
32
32
32
32
20
20
23
23
26
26
28
28
28
28
35
35
20
20
23
23
26
26
28
28
28
28
35
35
20
20
23
23
26
26
28
28
28
28
35
35
4
4
5
5
4
4
5
5
4
4
5
5
Clockwise
Anticlockwise
GROOVING
HSC05030
: 7.0Nm)
Dimensions (mm)
5 pcs.
LH 2
HBH
LH 2
LH
HF
CU
TD
IA
Fig. D
HF
Fig. C
LH
Insert selection
Seat
Size
E
Geometry name

Seat
Size
E
Breaker
CW
2.39mm
2.50mm

a
a
a

Seat
Size
Breaker
F013, F014
MF
MS
MM
BM
CW
2.39mm
2.50mm
2.74mm
F012, F013
GU
GS
GM 05-GM GFGS
Ball shape
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F102
F106
F033
EXTERNAL GROOVING

CDX
B
00 type holder
WF
CW
LF
LH

-GM
HF
CU
TD
IA
Fig. B
HF
Fig. A
CU
TD
IA
LH
CU
TD
IA
HF
Fig. F
HF
Fig. E
LH 2
LH
CU
TD
IA
LH 2
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
CDX
CUTDIA
Type
Modular
Mono Block
Modular
Modular
6
12
Mono Block
Modular
Modular
Modular
Modular
10
20
Modular
3.00
3.18
3.24
Modular
Modular
12
24
Modular
Modular
Modular
18 4
Mono Block
36
Modular
Modular
Mono Block
20 1
40 2
Modular
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
GYHR1616J00-M20R
GYHL1616J00-M20L
GYQR2020K00-F06
GYQL2020K00-F06
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYQR2525M00-F06
GYQL2525M00-F06
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR1616J00-M20R
GYHL1616J00-M20L
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR1616J00-M20R
GYHL1616J00-M20L
GYQR2020K00-F18
GYQL2020K00-F18
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYQR2525M00-F20
GYQL2525M00-F20
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Modular Blade
GYM20RA-F06
GYM20LA-F06
GYM20RA-F06
GYM20LA-F06
GYM25RA-F06
GYM25LA-F06
GYM25RA-F06
GYM25LA-F06
GYM25RA-F06
GYM25LA-F06
GYM25RA-F06
GYM25LA-F06
GYM20RA-F10
GYM20LA-F10
GYM20RA-F10
GYM20LA-F10
GYM25RA-F12
GYM25LA-F12
GYM25RA-F12
GYM25LA-F12
GYM25RA-F12
GYM25LA-F12
GYM25RA-F12
GYM25LA-F12
GYM20RB-F18
GYM20LB-F18
GYM20RB-F18
GYM20LB-F18
GYM25RA-F20
GYM25LA-F20
GYM25RA-F20
GYM25LA-F20
GYM25RA-F20
GYM25LA-F20
GYM25RA-F20
GYM25LA-F20
Stock
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
G
G
A
A
C
C
G
G
A
A
E
E
E
E
C
C
A
A
C
C
A
A
E
E
E
E
D
D
G
G
B
B
D
D
G
G
B
B
F
F
F
F
*12 The
*
a
F034
SPARE PARTS
WF
CW
CDX
Holder
LF
CU
TD
IA
H
HBH
HF
GY06013M
(Clamp Torque
: 6.0Nm)
*3
Dimensions (mm)
Wrench
HKY40R
TS407
(Clamp Torque
: 3.5Nm)
zTKY30R
xTKY15D
TS55
(Clamp Torque
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
16
16
20
20
20
20
20
20
25
25
25
25
32
32
32
32
16
16
20
20
20
20
25
25
32
32
32
32
16
16
20
20
20
20
20
20
25
25
25
25
32
32
32
32
16
16
20
20
20
20
20
20
25
25
25
25
25
25
32
32
16
16
20
20
20
20
25
25
25
25
32
32
16
16
20
20
20
20
20
20
25
25
25
25
25
25
32
32
104
104
125
125
119
119
117
117
150
150
142
142
162
162
162
162
110
110
125
125
125
125
150
150
170
170
170
170
116
116
125
125
131
131
131
131
150
150
156
156
176
176
176
176
28
28
36
36
28
28
31
31
36
36
31
31
31
31
31
31
34
34
34
34
39
39
39
39
39
39
39
39
40
40
39
39
40
40
45
45
41
41
45
45
45
45
45
45
44
44
43
43
52
52
49
49
49
49
49
49
50
50
49
49
60
60
57
57
57
57
57
57
56
56
55
55
66
66
63
63
63
63
63
63
16
16
20
20
20
20
20
20
25
25
25
25
32
32
32
32
16
16
20
20
20
20
25
25
32
32
32
32
16
16
20
20
20
20
20
20
25
25
25
25
32
32
32
32
20
20
20.3
20.3
23
23
26
26
25.3
25.3
28
28
28
28
35
35
20
20
23
23
26
26
28
28
28
28
35
35
20
20
20.25
20.25
23
23
26
26
25.25
25.25
28
28
28
28
35
35
4
4
5
5
4
4
5
5
4
4
5
5
Clockwise
Anticlockwise
GROOVING
IA
HSC05030
: 7.0Nm)
TD
CU
5 pcs.
LH 2
HBH
Fig. G
LH 2
LH
LH
HF
CU
TD
IA
Fig. D
HF
Fig. C
LH
Insert selection
Seat
Size
F
Geometry name

Seat
Size
F
Breaker
CW
3.00mm
3.18mm

a
Seat
Size
F013, F014
MF
MS
MM
BM
CW
3.00mm
RE 0.2
RE 0.4
RE 0.8
3.18mm
RE 0.2
RE 0.4
3.24mm
a
a

Breaker
F012, F013
GU
GS
GM 05-GM GFGS
Ball shape
a
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F102
F106
F035
EXTERNAL GROOVING

CDX
B
00 type holder
WF
CW
LF
LH

-GM
HF
CU
TD
IA
Fig. B
HF
Fig. A
CU
TD
IA
LH
CU
TD
IA
HF
Fig. F
HF
Fig. E
LH 2
LH
CU
TD
IA
LH 2
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
CDX
CUTDIA
Type
Mono Block
Modular
Mono Block
8
16
Modular
Modular
Modular
Modular
12
24
Modular
Modular
4.00
4.24
Modular
14
28
Modular
Modular
Mono Block
Modular
Mono Block
25 1
50 2
Modular
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYQR2020K00-G08
GYQL2020K00-G08
GYHR2020K00-M25R
GYHL2020K00-M25L
GYQR2525M00-G08
GYQL2525M00-G08
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR1616J00-M20R
GYHL1616J00-M20L
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYQR2020K00-G25
GYQL2020K00-G25
GYHR2020K00-M25R
GYHL2020K00-M25L
GYQR2525M00-G25
GYQL2525M00-G25
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
GYM25RA-G08
GYM25LA-G08
GYM25RA-G08
GYM25LA-G08
GYM25RA-G08
GYM25LA-G08
GYM25RA-G08
GYM25LA-G08
GYM20RA-G12
GYM20LA-G12
GYM20RA-G12
GYM20LA-G12
GYM25RA-G14
GYM25LA-G14
GYM25RA-G14
GYM25LA-G14
GYM25RA-G14
GYM25LA-G14
GYM25RA-G14
GYM25LA-G14
GYM25RA-G25
GYM25LA-G25
GYM25RA-G25
GYM25LA-G25
GYM25RA-G25
GYM25LA-G25
GYM25RA-G25
GYM25LA-G25
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
G
G
C
C
G
G
A
A
E
E
E
E
C
C
A
A
C
C
A
A
E
E
E
E
H
H
D
D
G
G
B
B
F
F
F
F
*12 The
*
F036
SPARE PARTS
WF
CW
CDX
Holder
LF
CU
TD
IA
H
HBH
HF
GY06013M
(Clamp Torque
: 6.0Nm)
*3
Dimensions (mm)
Wrench
HKY40R
TS407
(Clamp Torque
: 3.5Nm)
zTKY30R
xTKY15D
TS55
(Clamp Torque
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
20
20
25
25
25
25
32
32
32
32
16
16
20
20
20
20
25
25
32
32
32
32
20
20
20
20
25
25
25
25
32
32
32
32
20
20
20
20
25
25
25
25
25
25
32
32
16
16
20
20
20
20
25
25
25
25
32
32
20
20
20
20
25
25
25
25
25
25
32
32
125
125
119
119
150
150
144
144
164
164
164
164
110
110
125
125
125
125
150
150
170
170
170
170
125
125
136
136
150
150
161
161
181
181
181
181
41
41
33
33
41
41
33
33
33
33
33
33
34
34
34
34
39
39
39
39
39
39
39
39
46
46
50
50
46
46
50
50
50
50
50
50
54
54
51
51
51
51
51
51
50
50
49
49
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
20
20
20
20
25
25
25
25
32
32
32
32
16
16
20
20
20
20
25
25
32
32
32
32
20
20
20
20
25
25
25
25
32
32
32
32
20.35
20.35
26
26
25.35
25.35
28
28
28
28
35
35
20
20
23
23
26
26
28
28
28
28
35
35
20.35
20.35
26
26
25.35
25.35
28
28
28
28
35
35
5
5
4
4
5
5
4
4
5
5
Clockwise
Anticlockwise
GROOVING
IA
TD
CU
HF
HSC05030
: 7.0Nm)
Fig. H
TD
CU
LH 2
LH
5 pcs.
HBH
IA
HBH
Fig. G
LH 2
LH
LH
HF
CU
TD
IA
Fig. D
HF
Fig. C
LH
Insert selection
Seat
Size
G
Geometry name

Seat
Size
G
Breaker
CW
4.00mm

a

Seat
Size
Breaker
F013, F014
MF
MS
MM
BM
CW
4.00mm
RE 0.2
RE 0.4
RE 0.8
4.24mm
F012, F013
GU
GS
GM 05-GM GFGS
Ball shape
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F102
F106
F037
EXTERNAL GROOVING

CDX
B
00 type holder
WF
CW
LF
LH

-GM
HF
CU
TD
IA
Fig. B
HF
Fig. A
CU
TD
IA
LH
CU
TD
IA
HF
Fig. F
HF
Fig. E
LH 2
LH
CU
TD
IA
LH 2
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
CDX
CUTDIA
Type
Mono Block
Modular
Mono Block
8
16
Modular
Modular
Modular
Modular
12
24
Modular
4.75
5.00
5.24
Modular
Modular
14
28
Modular
Modular
Mono Block
Modular
Mono Block
25 1
50 2
Modular
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYQR2020K00-H08
GYQL2020K00-H08
GYHR2020K00-M25R
GYHL2020K00-M25L
GYQR2525M00-H08
GYQL2525M00-H08
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR1616J00-M20R
GYHL1616J00-M20L
GYHR2020K00-M20R
GYHL2020K00-M20L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYQR2020K00-H25
GYQL2020K00-H25
GYHR2020K00-M25R
GYHL2020K00-M25L
GYQR2525M00-H25
GYQL2525M00-H25
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
GYM25RA-H08
GYM25LA-H08
GYM25RA-H08
GYM25LA-H08
GYM25RA-H08
GYM25LA-H08
GYM25RA-H08
GYM25LA-H08
GYM20RA-H12
GYM20LA-H12
GYM20RA-H12
GYM20LA-H12
GYM25RA-H14
GYM25LA-H14
GYM25RA-H14
GYM25LA-H14
GYM25RA-H14
GYM25LA-H14
GYM25RA-H14
GYM25LA-H14
GYM25RA-H25
GYM25LA-H25
GYM25RA-H25
GYM25LA-H25
GYM25RA-H25
GYM25LA-H25
GYM25RA-H25
GYM25LA-H25
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
G
G
C
C
G
G
A
A
E
E
E
E
C
C
A
A
C
C
A
A
E
E
E
E
H
H
D
D
G
G
B
B
F
F
F
F
*12 The
*
F038
SPARE PARTS
WF
CW
CDX
Holder
LF
CU
TD
IA
H
HBH
HF
GY06013M
(Clamp Torque
: 6.0Nm)
*3
Dimensions (mm)
Wrench
HKY40R
TS407
(Clamp Torque
: 3.5Nm)
zTKY30R
xTKY15D
TS55
(Clamp Torque
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
20
20
25
25
25
25
32
32
32
32
16
16
20
20
20
20
25
25
32
32
32
32
20
20
20
20
25
25
25
25
32
32
32
32
20
20
20
20
25
25
25
25
25
25
32
32
16
16
20
20
20
20
25
25
25
25
32
32
20
20
20
20
25
25
25
25
25
25
32
32
125
125
119
119
150
150
144
144
164
164
164
164
110
110
125
125
125
125
150
150
170
170
170
170
125
125
136
136
150
150
161
161
181
181
181
181
41
41
33
33
41
41
33
33
33
33
33
33
34
34
34
34
39
39
39
39
39
39
39
39
46
46
50
50
46
46
50
50
50
50
50
50
54
54
51
51
51
51
51
51
50
50
49
49
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
20
20
20
20
25
25
25
25
32
32
32
32
16
16
20
20
20
20
25
25
32
32
32
32
20
20
20
20
25
25
25
25
32
32
32
32
20.35
20.35
26
26
25.35
25.35
28
28
28
28
35
35
20
20
23
23
26
26
28
28
28
28
35
35
20.35
20.35
26
26
25.35
25.35
28
28
28
28
35
35
5
5
4
4
5
5
4
4
5
5
Clockwise
Anticlockwise
GROOVING
IA
TD
CU
HF
HSC05030
: 7.0Nm)
Fig. H
TD
CU
LH 2
LH
5 pcs.
HBH
IA
HBH
Fig. G
LH 2
LH
LH
HF
CU
TD
IA
Fig. D
HF
Fig. C
LH
Insert selection
Seat
Size
H
Geometry name
GYoo0475/0500/0524HooooBreaker shown below

Seat
Size
H
Breaker
CW
4.75mm
5.00mm

a
a
a

Seat
Size
Breaker
F013, F014
MF
MS
MM
BM
CW
4.75mm
RE 0.2
RE 0.4
RE 0.8
5.00mm
RE 0.2
RE 0.4
RE 0.8
5.24mm
F012, F013
GU
GS
GM 05-GM GFGS
Ball shape
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F102
F106
F039
EXTERNAL GROOVING

CDX
B
00 type holder
WF
CW
LF
LH

-GM
HF
CU
TD
IA
Fig. B
HF
Fig. A
CU
TD
IA
LH
CU
TD
IA
HF
Fig. F
HF
Fig. E
LH 2
LH
CU
TD
IA
LH 2
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
CDX
CUTDIA
Type
Mono Block
Modular
Mono Block
8
16
Modular
Modular
Modular
Modular
6.00
6.31
6.35
Modular
14
28
Modular
Modular
Mono Block
Modular
Mono Block
25 1
50 2
Modular
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYQR2020K00-J08
GYQL2020K00-J08
GYHR2020K00-M25R
GYHL2020K00-M25L
GYQR2525M00-J08
GYQL2525M00-J08
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYQR2020K00-J25
GYQL2020K00-J25
GYHR2020K00-M25R
GYHL2020K00-M25L
GYQR2525M00-J25
GYQL2525M00-J25
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
GYM25RA-J08
GYM25LA-J08
GYM25RA-J08
GYM25LA-J08
GYM25RA-J08
GYM25LA-J08
GYM25RA-J08
GYM25LA-J08
GYM25RA-J14
GYM25LA-J14
GYM25RA-J14
GYM25LA-J14
GYM25RA-J14
GYM25LA-J14
GYM25RA-J14
GYM25LA-J14
GYM25RA-J25
GYM25LA-J25
GYM25RA-J25
GYM25LA-J25
GYM25RA-J25
GYM25LA-J25
GYM25RA-J25
GYM25LA-J25
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
G
G
C
C
G
G
A
A
E
E
E
E
C
C
A
A
E
E
E
E
H
H
D
D
G
G
B
B
F
F
F
F
*12 The
*
F040
SPARE PARTS
LF
CU
TD
IA
IA
LH 2
LH
: 7.0Nm)
HF
GY06013M
HBH
HSC05030
*3
Wrench
HKY40R
TS55
zTKY30R
GYHR/Looooooo-M25R/L (Clamp Torque (Clamp Torque xTKY25D

: 6.0Nm)
: 5.0Nm)

Dimensions (mm)
5 pcs.
TD
CU
HF
Holder
Fig. H
TD
CU
HBH
IA
HBH
Fig. G
LH 2
LH
LH
HF
CU
TD
IA
Fig. D
HF
Fig. C
LH
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
20
20
25
25
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
20
20
25
25
25
25
32
32
32
32
20
20
20
20
25
25
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
20
20
25
25
25
25
25
25
32
32
125
125
119
119
150
150
144
144
164
164
164
164
125
125
150
150
170
170
170
170
125
125
136
136
150
150
161
161
181
181
181
181
41
41
33
33
41
41
33
33
33
33
33
33
39
39
39
39
39
39
39
39
46
46
50
50
46
46
50
50
50
50
50
50
54
54
51
51
51
51
51
51
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
20
20
20
20
25
25
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
20
20
25
25
25
25
32
32
32
32
20.35
20.35
26
26
25.35
25.35
28
28
28
28
35
35
26
26
28
28
28
28
35
35
20.35
20.35
26
26
25.35
25.35
28
28
28
28
35
35
5
5
5
5
4
4
5
5
Clockwise
Anticlockwise
GROOVING
WF
CW
CDX
Insert selection
Seat
Size
J
Geometry name
GYoo0600/0631/0635JooooBreaker shown below

Seat
Size
J
Breaker
CW
6.00mm
6.35mm

a

Seat
Size
L
J
Breaker
F013, F014
MF
MS
MM
BM
CW
6.00mm
RE 0.2
RE 0.4
RE 0.8
6.31mm
6.35mm
RE 0.2
RE 0.4
RE 0.8
F012
GU
GS
GM 05-GM GFGS
Ball shape
a
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F102
F106
F041
EXTERNAL GROOVING

1
00 type holder
Insert GY2Mooooooooo-GS Insert GY2Mooooooooo-MS

Insert GY2Mooooooooo-GM Insert GY2Mooooooooo-MM
WF
CW
CDX
LF
IA
LH
Fig. J
D
UT
IA
LH
D
UT
LH 2
HF
HBH
HF
Fig. I

Insert GY2Mooooooooo-GM
LH 2
GROOVING

Seat
Size
CW
CDX
CUTDIA
Type
Mono Block
25 1
50 2
Mono Block
Mono Block
Hand
(R/L)
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYPR2525M00-K25
GYPL2525M00-K25
GYPR3225P00-K25
GYPL3225P00-K25
GYPR3232P00-K25
GYPL3232P00-K25
a
a
a
a
a
I
I
J
J
K
K
8.00
*12 The
*
F042
WF
CW
CDX
LF
SPARE PARTS
LH
IA
Fig. K
D
UT
Holder
H
LH 2
GYPR/Looooo00-K25
*3
Dimensions (mm)
Clamp Screw
Wrench
GY06013M
(Clamp Torque
: 6.0Nm)
TKY30R
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
25
25
32
32
32
32
25
25
25
25
32
32
150
150
170
170
170
170
47
47
47
47
47
47
48
48
48
48
48
48
25
25
32
32
32
32
28
28
28
28
35
35
7
7
Clockwise
Anticlockwise
GROOVING
HF
Insert selection
Seat
Size
K
Geometry name
GYoo0800KooooBreaker shown below

Seat
Size
K
Breaker
CW
8.00mm

Seat
Size
Breaker
F012
GU
GS
GM 05-GM GFGS
F013, F014
MF
MS
MM
BM
CW
8.00mm
RE 0.8
RE 1.2
Ball shape
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F102
F106
F043
EXTERNAL GROOVING

2
90 type holder
CW
Fig. A
Fig. B
CU
LH
LF
CU
TD
TD
IA
H
HF
IA
HF

-GM
CDX
WF
(Note 2) Please set the left hand modular blade at the right hand holder and the right hand

GROOVING
Seat
Size
CW
CDX
CUTDIA
Type
Modular
6
12
Modular
2.00
2.24
10
12
*
20 1
*
18 4
Modular
20
Modular
24
Modular
36
40 2
Modular
Modular
12
Modular
2.39
2.50
2.74
10
12
*
20 1
*
18 4
20
Modular
Modular
24
Modular
36
40 2
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
Stock
Modular Blade
Stock
GYM20LA-D06
GYM20RA-D06
GYM25LA-D06
GYM25RA-D06
GYM20LA-D10
GYM20RA-D10
GYM25LA-D12
GYM25RA-D12
GYM20LB-D18
GYM20RB-D18
GYM25LA-D20
GYM25RA-D20
GYM20LA-E06
GYM20RA-E06
GYM25LA-E06
GYM25RA-E06
GYM20LA-E10
GYM20RA-E10
GYM25LA-E12
GYM25RA-E12
GYM20LB-E18
GYM20RB-E18
GYM25LA-E20
GYM25RA-E20
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
A
A
A
A
A
A
A
A
B
B
B
B
A
A
A
A
A
A
A
A
B
B
B
B
1 The maximum groove depth varies according to the insert used. Please refer to the maximum groove depth of inserts on pages F012 F014.
2 The maximum cut off diameter CUTDIA varies according to the insert used. The cut off diameter is double the maximum groove depth (CDX) of inserts on pages F012 F014.
3 Dimensions shown are when the gauge insert is used. If other insert geometries are used then LF, LH and WF values may vary.
4 The maximum groove depth is limited by the workpiece diameter. For details, please refer to page F104.
*
*
*
*
F044
SPARE PARTS
Holder
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
*3
TS407
(Clamp Torque
GY06013M : 3.5Nm)
(Clamp Torque
TS55
: 6.0Nm)
(Clamp Torque
: 5.0Nm)
Wrench
zTKY30R
xTKY15D
zTKY30R
xTKY25D
GROOVING
GYHR2020K90-M20L
Dimensions (mm)
5 pcs.
Cutting Mode
LF
LH
HF
WF
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
125
125
150
150
125
125
150
150
125
125
150
150
125
125
150
150
125
125
150
150
125
125
150
150
35
35
38
38
35
35
38
38
35
35
38
38
35
35
38
38
35
35
38
38
35
35
38
38
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
39
39
45
45
45
45
53
53
51
51
59
59
39
39
45
45
45
45
53
53
51
51
59
59
Insert selection
R
Seat
Size
D
E
Geometry name

Seat
Size
D
E
Breaker
CW
2.00mm
2.39mm
2.50mm

a
Seat
Size
D
E
a
F013, F014
MF
MS
MM
BM
CW
2.00mm
2.24mm
2.39mm
2.50mm
2.74mm
a
a

Breaker
F012, F013
GU
GS
GM 05-GM GFGS
Ball shape
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F102
F106
F045
EXTERNAL GROOVING

2
90 type holder
CW
Fig. A
Fig. B
CU
LF
CU
TD
LH
TD
IA
HF
IA
HF

-GM
CDX
WF
GROOVING

Seat
Size
CW
CDX
CUTDIA
Type
Modular
6
12
Modular
3.00
3.18
3.24
10
12
*
20 1
*
8
Modular
36
40 2
Modular
24
14
Modular
28
25 1
Modular
Modular
16
12
Modular
24
18 4
4.00
4.24
Modular
20
50 2
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYM20LA-F06
GYM20RA-F06
GYM25LA-F06
GYM25RA-F06
GYM20LA-F10
GYM20RA-F10
GYM25LA-F12
GYM25RA-F12
GYM20LB-F18
GYM20RB-F18
GYM25LA-F20
GYM25RA-F20
GYM25LA-G08
GYM25RA-G08
GYM20LA-G12
GYM20RA-G12
GYM25LA-G14
GYM25RA-G14
GYM25LA-G25
GYM25RA-G25
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
A
A
A
A
A
A
A
A
B
B
B
B
A
A
A
A
A
A
B
B
*12 The
*3 Dimensions shown are when the gauge insert is used. If other insert geometries are used then LF, LH and WF values may vary.
*
F046
SPARE PARTS
Holder
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
*3
TS407
(Clamp Torque
GY06013M : 3.5Nm)
(Clamp Torque
TS55
: 6.0Nm)
(Clamp Torque
: 5.0Nm)
Wrench
zTKY30R
xTKY15D
zTKY30R
xTKY25D
GROOVING
GYHR2020K90-M20L
Dimensions (mm)
5 pcs.
Cutting Mode
LF
LH
HF
WF
20
20
25
25
20
20
25
25
20
20
25
25
25
25
20
20
25
25
25
25
20
20
25
25
20
20
25
25
20
20
25
25
25
25
20
20
25
25
25
25
125
125
150
150
125
125
150
150
125
125
150
150
150
150
125
125
150
150
150
150
35
35
38
38
35
35
38
38
35
35
38
38
38
38
35
35
38
38
38
38
20
20
25
25
20
20
25
25
20
20
25
25
25
25
20
20
25
25
25
25
39
39
45
45
45
45
53
53
51
51
59
59
47
47
45
45
53
53
64
64
Insert selection
R
Seat
Size
F
G
Geometry name
GYoo0400/0424GooooBreaker shown below

Seat
Size
F
G
Breaker
CW
3.00mm
3.18mm
4.00mm

a
Seat
Size
F013, F014
MF
MS
MM
BM
CW
3.00mm
RE 0.2
RE 0.4
RE 0.8
3.18mm
RE 0.2
RE 0.4
3.24mm
4.00mm
RE 0.2
RE 0.4
RE 0.8
4.24mm
a
a

Breaker
F012, F013
GU
GS
GM 05-GM GFGS
Ball shape
a
a
a
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F102
F106
F047
EXTERNAL GROOVING

2
90 type holder
CW
Fig. A
Fig. B
CU
LF
CU
TD
LH
TD
IA
HF
IA
HF

-GM
CDX
WF
GROOVING

Seat
Size
CW
4.75
5.00
5.24
6.00
6.31
6.35
CDX
CUTDIA
Type
16
Modular
12
24
Modular
14
Modular
28
50 2
Modular
16
Modular
14
28
Modular
25 1
25 1
50 2
Modular
Hand
(R/L)
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
R
L
R
L
R
L
R
L
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2020K90-M20L
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYM25LA-H08
GYM25RA-H08
GYM20LA-H12
GYM20RA-H12
GYM25LA-H14
GYM25RA-H14
GYM25LA-H25
GYM25RA-H25
R
L
R
L
R
L
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYM25LA-J08
GYM25RA-J08
GYM25LA-J14
GYM25RA-J14
GYM25LA-J25
GYM25RA-J25
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
A
A
A
A
A
A
B
B
A
A
A
A
B
B
*12 The
*3 Dimensions shown are when the gauge insert is used. If other insert geometries are used then LF, LH and WF values may vary.
*
F048
SPARE PARTS
Holder Number
GYHL2020K90-M20R
GYHR2525M90-M25L
GYHL2525M90-M25R
*3
LF
LH
HF
WF
25
25
20
20
25
25
25
25
25
25
20
20
25
25
25
25
150
150
125
125
150
150
150
150
38
38
35
35
38
38
38
38
25
25
20
20
25
25
25
25
47
47
45
45
53
53
64
64
150
150
150
150
150
150
38
38
38
38
38
38
25
25
25
25
25
25
zTKY30R
xTKY15D
zTKY30R
xTKY25D
Insert selection
R
Seat
Size
H
J
47
47
53
53
64
64
Geometry name

Seat
Size
H
25
25
25
25
25
25
Cutting Mode
25
25
25
25
25
25
TS407
(Clamp Torque
GY06013M : 3.5Nm)
(Clamp Torque
TS55
: 6.0Nm)
(Clamp Torque
: 5.0Nm)
Wrench
GROOVING
GYHR2020K90-M20L
Dimensions (mm)
5 pcs.
Breaker
CW
4.75mm
5.00mm
6.00mm
6.35mm

a
a
a

Seat
Size
Breaker
F013, F014
MF
MS
MM
BM
CW
4.75mm
RE 0.2
RE 0.4
RE 0.8
5.00mm
RE 0.2
RE 0.4
RE 0.8
5.24mm
6.00mm
RE 0.2
RE 0.4
RE 0.8
6.31mm
6.35mm
RE 0.2
RE 0.4
RE 0.8
F012, F013
GU
GS
GM 05-GM GFGS
Ball shape
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F102
F106
F049
EXTERNAL GROOVING
GYSERIES (FOR EXTERNAL RECESSING)

For 50 recessing holder
DMIN
Insert GY2Mooooooooo-BM
APMX 2
WF
PM
A
50
5m
0.
APMX 2
F2
X
D
C
45
Fig. A
LF
LH
CW
HF
Enlarged view
GROOVING

Seat
Size
CW
2.00
CDX DMIN APMX APMX 2
Type
Modular
1.5
0.646
Modular
Modular
2.50
30
1.75 0.72
Modular
Modular
3.00
3.18
0.793
Modular
0.5
Modular
4.00
2.5
0.939
Modular
4.75
5.00
6.00
6.35
Modular
20
2.88 1.049
Modular
3.5
1.232
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K50-M20L
GYHL2020K50-M20R
GYHR2525M50-M25L
GYHL2525M50-M25R
GYHR2020K50-M20L
GYHL2020K50-M20R
GYHR2525M50-M25L
GYHL2525M50-M25R
GYHR2020K50-M20L
GYHL2020K50-M20R
GYHR2525M50-M25L
GYHL2525M50-M25R
GYHR2020K50-M20L
GYHL2020K50-M20R
GYHR2525M50-M25L
GYHL2525M50-M25R
GYHR2020K50-M20L
GYHL2020K50-M20R
GYHR2525M50-M25L
GYHL2525M50-M25R
GYHR2525M50-M25L
GYHL2525M50-M25R
GYM20LC-D005
GYM20RC-D005
GYM25LC-D005
GYM25RC-D005
GYM20LC-E005
GYM20RC-E005
GYM25LC-E005
GYM25RC-E005
GYM20LC-F005
GYM20RC-F005
GYM25LC-F005
GYM25RC-F005
GYM20LC-G005
GYM20RC-G005
GYM25LC-G005
GYM25RC-G005
GYM20LC-H005
GYM20RC-H005
GYM25LC-H005
GYM25RC-H005
GYM25LC-J005
GYM25RC-J005
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
be used because external and face grooving blade interferes with the work.
*12 Cannot
Dimensions shown are when the gauge insert is used. If other insert geometries are used then LF, LH, WF and F2 values may vary.
*
F050
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
SPARE PARTS
Holder
5 pcs.
Wrench

TS407
(Clamp Torque
GYHR/L2020K50-M20R/L
GY06013M
: 3.5Nm)
(Clamp Torque
TS55
: 6.0Nm)
(Clamp Torque
GYHR/L2525M50-M25R/L
: 5.0Nm)
*2
zTKY30R
xTKY25D
zTKY30R
xTKY25D
Cutting Mode
LF
LH
HF
WF
F2
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
25
25
125
125
150
150
125
125
150
150
125
125
150
150
125
125
150
150
125
125
150
150
150
150
40
40
45
45
40
40
45
45
40
40
45
45
40
40
45
45
40
40
45
45
44
44
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
20
20
25
25
25
25
32
32
35
35
32
32
35
35
32
32
35
35
32
32
35
35
33
33
36
36
36
36
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
2.0
2.0
2.0
2.0
2.4
2.4
2.4
2.4
2.8
2.8
2.8
2.8
3.4
3.4
GROOVING
Dimensions (mm)
Insert selection
R
Geometry name
GY2MooooooooN-BM

Seat
Size
D
E
F
G
H
J
a
Breaker
F014
BM
(Copying, Recessing)
CW
Ball shape
2.00mm
2.50mm
3.00mm
3.18mm
4.00mm
4.75mm
5.00mm
6.00mm
6.35mm
a
a
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F105
F105
F051
FACE GROOVING
GYSERIES (FACE GROOVING)

4
00 type holder
CDX
B
WF
CW
LF
Fig. E
LH
H
LH 2
HF
XX
/DA
XN
DA
XX
/DA
XN
DA
LH
HF
Fig. A
LH 2
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
40
50
12
Modular
Modular
Modular
Modular
50
60
12
Modular
Modular
2.00
2.24
Modular
Modular
60
75
12
Modular
Modular
Modular
Modular
75
100
12
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-D12-040
GYM25LD-D12-040
GYM25RD-D12-040
GYM25LD-D12-040
GYM25RD-D12-040
GYM25LD-D12-040
GYM25RD-D12-040
GYM25LD-D12-040
GYM25RD-D12-050
GYM25LD-D12-050
GYM25RD-D12-050
GYM25LD-D12-050
GYM25RD-D12-050
GYM25LD-D12-050
GYM25RD-D12-050
GYM25LD-D12-050
GYM25RD-D12-060
GYM25LD-D12-060
GYM25RD-D12-060
GYM25LD-D12-060
GYM25RD-D12-060
GYM25LD-D12-060
GYM25RD-D12-060
GYM25LD-D12-060
GYM25RD-D12-075
GYM25LD-D12-075
GYM25RD-D12-075
GYM25LD-D12-075
GYM25RD-D12-075
GYM25LD-D12-075
GYM25RD-D12-075
GYM25LD-D12-075
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*1 Dimensions shown are when gauge insert is used. If other insert geometries are used then LF, LH, LH 2, and WF values may vary.
F052
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
SPARE PARTS
WF
CW
CDX
z
LF
Holder
5 pcs.
Fig. C
Wrench
XN
DA
LH
H
HBH
LH 2
GYHR/L2525M00-M25R/L GY06013M
GYHR/L3225P00-M25R/L
*1
Dimensions (mm)
TS55
(Clamp Torque (Clamp Torque
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
5
5
GROOVING
HF
XX
/DA
Insert selection
R
Seat
Size
D
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
(For gummy steel) (Low) (Medium) (Hardened steel)
D
2.00mm

Seat
Size
D
a
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
(Low) (Medium) (Copying)
CW
2.00mm
2.24mm
Ball shape
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F053
FACE GROOVING

4
00 type holder
CDX
B
WF
CW
LF
Fig. E
DA
LH
HF
HF
XX
XX
/DA
/DA
XN
XN
DA
LH
LH 2
Fig. A
LH 2

GROOVING
Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
100 150
12
Modular
Modular
Modular
2.00
2.24
Modular
135 200
12
Modular
Modular
Modular
Modular
180 250
12
Modular
Modular
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-D12-100
GYM25LD-D12-100
GYM25RD-D12-100
GYM25LD-D12-100
GYM25RD-D12-100
GYM25LD-D12-100
GYM25RD-D12-100
GYM25LD-D12-100
GYM25RD-D12-135
GYM25LD-D12-135
GYM25RD-D12-135
GYM25LD-D12-135
GYM25RD-D12-135
GYM25LD-D12-135
GYM25RD-D12-135
GYM25LD-D12-135
GYM25RD-D12-180
GYM25LD-D12-180
GYM25RD-D12-180
GYM25LD-D12-180
GYM25RD-D12-180
GYM25LD-D12-180
GYM25RD-D12-180
GYM25LD-D12-180
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
1 Dimensions shown are when gauge insert is used. If other insert geometries are used then LF, LH, LH 2, and WF values may vary.
F054
Hand
(R/L)
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
SPARE PARTS
WF
CW
CDX
z
LF
Holder
5 pcs.
Fig. C
Wrench
XN
DA
LH
H
HBH
LH 2
*1
Dimensions (mm)
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
GROOVING
HF
XX
/DA
Insert selection
R
Seat
Size
D
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
D
2.00mm

Seat
Size
L
D
a
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
2.00mm
2.24mm
Ball shape
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F055
FACE GROOVING

4
00 type holder
CDX
B
WF
CW
LF
Fig. E
DA
LH
HF
HF
XX
XX
/DA
/DA
XN
XN
DA
LH
LH 2
Fig. A
LH 2
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
40
50
12
Modular
Modular
Modular
Modular
50
60
12
Modular
2.39
2.50
2.74
Modular
Modular
Modular
60
75
12
Modular
Modular
Modular
Modular
75
100
12
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-E12-040
GYM25LD-E12-040
GYM25RD-E12-040
GYM25LD-E12-040
GYM25RD-E12-040
GYM25LD-E12-040
GYM25RD-E12-040
GYM25LD-E12-040
GYM25RD-E12-050
GYM25LD-E12-050
GYM25RD-E12-050
GYM25LD-E12-050
GYM25RD-E12-050
GYM25LD-E12-050
GYM25RD-E12-050
GYM25LD-E12-050
GYM25RD-E12-060
GYM25LD-E12-060
GYM25RD-E12-060
GYM25LD-E12-060
GYM25RD-E12-060
GYM25LD-E12-060
GYM25RD-E12-060
GYM25LD-E12-060
GYM25RD-E12-075
GYM25LD-E12-075
GYM25RD-E12-075
GYM25LD-E12-075
GYM25RD-E12-075
GYM25LD-E12-075
GYM25RD-E12-075
GYM25LD-E12-075
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*1 Dimensions shown are when gauge insert is used. If other insert geometries are used then LF, LH, LH 2, and WF values may vary.
F056
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
SPARE PARTS
WF
CW
CDX
z
LF
Holder Number
5 pcs.
Fig. C
Wrench
XN
DA
LH
H
HBH
LH 2
*1
Dimensions (mm)
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
5
5
GROOVING
HF
XX
/DA
Insert selection
R
Seat
Size
E
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
E
2.39mm
2.50mm

Seat
Size
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
2.39mm
2.50mm
2.74mm
Ball shape
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F057
FACE GROOVING

4
00 type holder
CDX
B
WF
CW
LF
Fig. E
DA
LH
HF
HF
XX
XX
/DA
/DA
XN
XN
DA
LH
LH 2
Fig. A
LH 2

GROOVING
Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
100 150
12
Modular
Modular
Modular
2.39
2.50
2.74
Modular
135 200
12
Modular
Modular
Modular
Modular
180 250
12
Modular
Modular
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-E12-100
GYM25LD-E12-100
GYM25RD-E12-100
GYM25LD-E12-100
GYM25RD-E12-100
GYM25LD-E12-100
GYM25RD-E12-100
GYM25LD-E12-100
GYM25RD-E12-135
GYM25LD-E12-135
GYM25RD-E12-135
GYM25LD-E12-135
GYM25RD-E12-135
GYM25LD-E12-135
GYM25RD-E12-135
GYM25LD-E12-135
GYM25RD-E12-180
GYM25LD-E12-180
GYM25RD-E12-180
GYM25LD-E12-180
GYM25RD-E12-180
GYM25LD-E12-180
GYM25RD-E12-180
GYM25LD-E12-180
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
F058
Hand
(R/L)
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
SPARE PARTS
WF
CW
CDX
z
LF
Holder
5 pcs.
Fig. C
Wrench
XN
DA
LH
H
HBH
LH 2
*1
Dimensions (mm)
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
GROOVING
HF
XX
/DA
Insert selection
R
Seat
Size
E
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
E
2.39mm
2.50mm
Seat
Size
E
a
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
2.39mm
2.50mm
2.74mm
Ball shape
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F059
FACE GROOVING

4
00 type holder
CDX
B
WF
CW
LF
Fig. E
DA
LH
HF
HF
XX
XX
/DA
/DA
XN
XN
DA
LH
LH 2
Fig. A
LH 2

GROOVING
Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
35
40
12
Modular
Modular
Modular
3.00
3.18
3.24
Modular
40
50
12
Modular
Modular
Modular
Modular
50
60
12
Modular
Modular
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-F12-035
GYM25LD-F12-035
GYM25RD-F12-035
GYM25LD-F12-035
GYM25RD-F12-035
GYM25LD-F12-035
GYM25RD-F12-035
GYM25LD-F12-035
GYM25RD-F12-040
GYM25LD-F12-040
GYM25RD-F12-040
GYM25LD-F12-040
GYM25RD-F12-040
GYM25LD-F12-040
GYM25RD-F12-040
GYM25LD-F12-040
GYM25RD-F12-050
GYM25LD-F12-050
GYM25RD-F12-050
GYM25LD-F12-050
GYM25RD-F12-050
GYM25LD-F12-050
GYM25RD-F12-050
GYM25LD-F12-050
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
F060
Hand
(R/L)
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
SPARE PARTS
WF
CW
CDX
z
LF
Holder
5 pcs.
Fig. C
Wrench
XN
DA
LH
H
HBH
LH 2
*1
Dimensions (mm)
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
GROOVING
HF
XX
/DA
Insert selection
R
Seat
Size
F
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
F
3.00mm
3.18mm
Seat
Size
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
3.00mm
RE 0.2
RE 0.4
RE 0.8
3.18mm
RE 0.2
RE 0.4
3.24mm
Ball shape
a
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F061
FACE GROOVING

CDX
B
00 type holder
WF
CW
LF
LH
HF
Fig. B
HF
Fig. A
LH 2
LH 2
XX
A
/D
XN
A
D
LH
HF
Fig. F
HF
Fig. E
LH
XX
A
/D
XN
A
D
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
12
Modular
Modular
60
75
Modular
Modular
20 2
3.00
3.18
3.24
Modular
Modular
Modular
Modular
12
Modular
Modular
75
100
Modular
Modular
20 2
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-F12-060
GYM25LD-F12-060
GYM25RD-F12-060
GYM25LD-F12-060
GYM25RD-F12-060
GYM25LD-F12-060
GYM25RD-F12-060
GYM25LD-F12-060
GYM25RD-F20-060
GYM25LD-F20-060
GYM25RD-F20-060
GYM25LD-F20-060
GYM25RD-F20-060
GYM25LD-F20-060
GYM25RD-F20-060
GYM25LD-F20-060
GYM25RD-F12-075
GYM25LD-F12-075
GYM25RD-F12-075
GYM25LD-F12-075
GYM25RD-F12-075
GYM25LD-F12-075
GYM25RD-F12-075
GYM25LD-F12-075
GYM25RD-F20-075
GYM25LD-F20-075
GYM25RD-F20-075
GYM25LD-F20-075
GYM25RD-F20-075
GYM25LD-F20-075
GYM25RD-F20-075
GYM25LD-F20-075
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
Dimensions shown are when gauge insert is used. If other insert geometries are used then LF, LH, LH 2, and WF values may vary.
*21 The
* maximum groove depth varies according to the insert used. Please refer to the maximum groove depth of inserts on pages F012 F014.
F062
WF
CW
CDX
SPARE PARTS
LF
LH
Fig. D
*1
Wrench
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
131
131
156
156
176
176
176
176
125
125
150
150
170
170
170
170
131
131
156
156
176
176
176
176
39
39
39
39
39
39
39
39
45
45
45
45
45
45
45
45
39
39
39
39
39
39
39
39
45
45
45
45
45
45
45
45
60
60
57
57
57
57
57
57
66
66
63
63
63
63
63
63
60
60
57
57
57
57
57
57
66
66
63
63
63
63
63
63
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
5
5
GROOVING
Dimensions (mm)
5 pcs.
HBH
LH 2
HBH
LH 2
Holder
HF
Fig. C
HF
XX
A
/D
XN
A
D
LH
Insert selection
R
Seat
Size
F
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
F
3.00mm
3.18mm

Seat
Size
L
F
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
3.00mm
RE 0.2
RE 0.4
RE 0.8
3.18mm
RE 0.2
RE 0.4
3.24mm
Ball shape
a
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F063
FACE GROOVING

CDX
B
00 type holder
WF
CW
LF
LH
HF
Fig. B
HF
Fig. A
LH 2
LH 2
XX
A
/D
XN
A
D
LH
HF
Fig. F
HF
Fig. E
LH
XX
A
/D
XN
A
D
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
12
Modular
Modular
100 150
Modular
Modular
20 2
3.00
3.18
3.24
Modular
Modular
Modular
Modular
12
Modular
Modular
135 200
Modular
Modular
20 2
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-F12-100
GYM25LD-F12-100
GYM25RD-F12-100
GYM25LD-F12-100
GYM25RD-F12-100
GYM25LD-F12-100
GYM25RD-F12-100
GYM25LD-F12-100
GYM25RD-F20-100
GYM25LD-F20-100
GYM25RD-F20-100
GYM25LD-F20-100
GYM25RD-F20-100
GYM25LD-F20-100
GYM25RD-F20-100
GYM25LD-F20-100
GYM25RD-F12-135
GYM25LD-F12-135
GYM25RD-F12-135
GYM25LD-F12-135
GYM25RD-F12-135
GYM25LD-F12-135
GYM25RD-F12-135
GYM25LD-F12-135
GYM25RD-F20-135
GYM25LD-F20-135
GYM25RD-F20-135
GYM25LD-F20-135
GYM25RD-F20-135
GYM25LD-F20-135
GYM25RD-F20-135
GYM25LD-F20-135
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
*21 The
F064
WF
CW
CDX
SPARE PARTS
LF
LH
Fig. D
*1
Wrench
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
131
131
156
156
176
176
176
176
125
125
150
150
170
170
170
170
131
131
156
156
176
176
176
176
39
39
39
39
39
39
39
39
45
45
45
45
45
45
45
45
39
39
39
39
39
39
39
39
45
45
45
45
45
45
45
45
60
60
57
57
57
57
57
57
66
66
63
63
63
63
63
63
60
60
57
57
57
57
57
57
66
66
63
63
63
63
63
63
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
5
5
GROOVING
Dimensions (mm)
5 pcs.
HBH
LH 2
HBH
LH 2
Holder
HF
Fig. C
HF
XX
A
/D
XN
A
D
LH
Insert selection
R
Seat
Size
F
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
F
3.00mm
3.18mm

Seat
Size
L
F
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
3.00mm
RE 0.2
RE 0.4
RE 0.8
3.18mm
RE 0.2
RE 0.4
3.24mm
Ball shape
a
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F065
FACE GROOVING

CDX
B
00 type holder
WF
CW
LF
LH
HF
Fig. B
HF
Fig. A
LH 2
LH 2
XX
A
/D
XN
A
D
LH
HF
Fig. F
HF
Fig. E
LH
XX
A
/D
XN
A
D
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
12
Modular
Modular
180 250
Modular
Modular
20 2
3.00
3.18
3.24
Modular
Modular
Modular
Modular
12
Modular
Modular
225 999
Modular
Modular
20 2
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-F12-180
GYM25LD-F12-180
GYM25RD-F12-180
GYM25LD-F12-180
GYM25RD-F12-180
GYM25LD-F12-180
GYM25RD-F12-180
GYM25LD-F12-180
GYM25RD-F20-180
GYM25LD-F20-180
GYM25RD-F20-180
GYM25LD-F20-180
GYM25RD-F20-180
GYM25LD-F20-180
GYM25RD-F20-180
GYM25LD-F20-180
GYM25RD-F12-225
GYM25LD-F12-225
GYM25RD-F12-225
GYM25LD-F12-225
GYM25RD-F12-225
GYM25LD-F12-225
GYM25RD-F12-225
GYM25LD-F12-225
GYM25RD-F20-225
GYM25LD-F20-225
GYM25RD-F20-225
GYM25LD-F20-225
GYM25RD-F20-225
GYM25LD-F20-225
GYM25RD-F20-225
GYM25LD-F20-225
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
*21 The
F066
WF
CW
CDX
SPARE PARTS
LF
LH
Fig. D
*1
Wrench
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
131
131
156
156
176
176
176
176
125
125
150
150
170
170
170
170
131
131
156
156
176
176
176
176
39
39
39
39
39
39
39
39
45
45
45
45
45
45
45
45
39
39
39
39
39
39
39
39
45
45
45
45
45
45
45
45
60
60
57
57
57
57
57
57
66
66
63
63
63
63
63
63
60
60
57
57
57
57
57
57
66
66
63
63
63
63
63
63
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
5
5
GROOVING
Dimensions (mm)
5 pcs.
HBH
LH 2
HBH
LH 2
Holder
HF
Fig. C
HF
XX
A
/D
XN
A
D
LH
Insert selection
R
Seat
Size
F
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
F
3.00mm
3.18mm

Seat
Size
L
F
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
3.00mm
RE 0.2
RE 0.4
RE 0.8
3.18mm
RE 0.2
RE 0.4
3.24mm
Ball shape
a
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F067
FACE GROOVING

CDX
B
00 type holder
WF
CW
LF
LH
HF
Fig. B
HF
Fig. A
LH 2
LH 2
XX
A
/D
XN
A
D
LH
HF
Fig. F
HF
Fig. E
LH
XX
A
/D
XN
A
D
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
40
50
14
Modular
Modular
Modular
Modular
50
60
14
Modular
Modular
4.00
4.24
Modular
Modular
14
Modular
Modular
60
85
Modular
Modular
25 2
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-G14-040
GYM25LD-G14-040
GYM25RD-G14-040
GYM25LD-G14-040
GYM25RD-G14-040
GYM25LD-G14-040
GYM25RD-G14-040
GYM25LD-G14-040
GYM25RD-G14-050
GYM25LD-G14-050
GYM25RD-G14-050
GYM25LD-G14-050
GYM25RD-G14-050
GYM25LD-G14-050
GYM25RD-G14-050
GYM25LD-G14-050
GYM25RD-G14-060
GYM25LD-G14-060
GYM25RD-G14-060
GYM25LD-G14-060
GYM25RD-G14-060
GYM25LD-G14-060
GYM25RD-G14-060
GYM25LD-G14-060
GYM25RD-G25-060
GYM25LD-G25-060
GYM25RD-G25-060
GYM25LD-G25-060
GYM25RD-G25-060
GYM25LD-G25-060
GYM25RD-G25-060
GYM25LD-G25-060
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
*21 The
F068
WF
CW
CDX
SPARE PARTS
LF
LH
Fig. D
*1
Wrench
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
5
5
GROOVING
Dimensions (mm)
5 pcs.
HBH
LH 2
HBH
LH 2
Holder
HF
Fig. C
HF
XX
A
/D
XN
A
D
LH
Insert selection
R
Seat
Size
G
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
G
4.00mm

Seat
Size
L
a
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
4.00mm
RE 0.2
RE 0.4
RE 0.8
4.24mm
Ball shape
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F069
FACE GROOVING

CDX
B
00 type holder
WF
CW
LF
LH
HF
Fig. B
HF
Fig. A
LH 2
LH 2
XX
A
/D
XN
A
D
LH
HF
Fig. F
HF
Fig. E
LH
XX
A
/D
XN
A
D
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
14
Modular
Modular
85 125
Modular
Modular
25 2
Modular
Modular
4.00
4.24
Modular
Modular
14
Modular
Modular
125 200
Modular
Modular
25 2
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-G14-085
GYM25LD-G14-085
GYM25RD-G14-085
GYM25LD-G14-085
GYM25RD-G14-085
GYM25LD-G14-085
GYM25RD-G14-085
GYM25LD-G14-085
GYM25RD-G25-085
GYM25LD-G25-085
GYM25RD-G25-085
GYM25LD-G25-085
GYM25RD-G25-085
GYM25LD-G25-085
GYM25RD-G25-085
GYM25LD-G25-085
GYM25RD-G14-125
GYM25LD-G14-125
GYM25RD-G14-125
GYM25LD-G14-125
GYM25RD-G14-125
GYM25LD-G14-125
GYM25RD-G14-125
GYM25LD-G14-125
GYM25RD-G25-125
GYM25LD-G25-125
GYM25RD-G25-125
GYM25LD-G25-125
GYM25RD-G25-125
GYM25LD-G25-125
GYM25RD-G25-125
GYM25LD-G25-125
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
*21 The
F070
WF
CW
CDX
SPARE PARTS
LF
LH
Fig. D
*1
Wrench
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
5
5
GROOVING
Dimensions (mm)
5 pcs.
HBH
LH 2
HBH
LH 2
Holder
HF
Fig. C
HF
XX
A
/D
XN
A
D
LH
Insert selection
R
Seat
Size
G
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
G
4.00mm

Seat
Size
L
a
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
4.00mm
RE 0.2
RE 0.4
RE 0.8
4.24mm
Ball shape
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F071
FACE GROOVING

CDX
B
00 type holder
WF
CW
LF
LH
HF
Fig. B
HF
Fig. A
LH 2
LH 2
XX
A
/D
XN
A
D
LH
HF
Fig. F
HF
Fig. E
LH
XX
A
/D
XN
A
D
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
14
Modular
Modular
180 280
Modular
Modular
25 2
Modular
Modular
4.00
4.24
Modular
Modular
14
Modular
Modular
250 999
Modular
Modular
25 2
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-G14-180
GYM25LD-G14-180
GYM25RD-G14-180
GYM25LD-G14-180
GYM25RD-G14-180
GYM25LD-G14-180
GYM25RD-G14-180
GYM25LD-G14-180
GYM25RD-G25-180
GYM25LD-G25-180
GYM25RD-G25-180
GYM25LD-G25-180
GYM25RD-G25-180
GYM25LD-G25-180
GYM25RD-G25-180
GYM25LD-G25-180
GYM25RD-G14-250
GYM25LD-G14-250
GYM25RD-G14-250
GYM25LD-G14-250
GYM25RD-G14-250
GYM25LD-G14-250
GYM25RD-G14-250
GYM25LD-G14-250
GYM25RD-G25-250
GYM25LD-G25-250
GYM25RD-G25-250
GYM25LD-G25-250
GYM25RD-G25-250
GYM25LD-G25-250
GYM25RD-G25-250
GYM25LD-G25-250
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
*21 The
F072
WF
CW
CDX
SPARE PARTS
LF
LH
Fig. D
*1
Wrench
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
5
5
GROOVING
Dimensions (mm)
5 pcs.
HBH
LH 2
HBH
LH 2
Holder
HF
Fig. C
HF
XX
A
/D
XN
A
D
LH
Insert selection
R
Seat
Size
G
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
G
4.00mm

Seat
Size
L
a
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
4.00mm
RE 0.2
RE 0.4
RE 0.8
4.24mm
Ball shape
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F073
FACE GROOVING

CDX
B
00 type holder
WF
CW
LF
LH
HF
Fig. B
HF
Fig. A
LH 2
LH 2
XX
A
/D
XN
A
D
LH
HF
Fig. F
HF
Fig. E
LH
XX
A
/D
XN
A
D
LH
LH 2
LH 2

GROOVING
Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
50
60
14
Modular
Modular
Modular
4.75
5.00
5.24
Modular
14
Modular
Modular
60
85
Modular
Modular
25 2
Modular
Modular
*
*
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-H14-050
GYM25LD-H14-050
GYM25RD-H14-050
GYM25LD-H14-050
GYM25RD-H14-050
GYM25LD-H14-050
GYM25RD-H14-050
GYM25LD-H14-050
GYM25RD-H14-060
GYM25LD-H14-060
GYM25RD-H14-060
GYM25LD-H14-060
GYM25RD-H14-060
GYM25LD-H14-060
GYM25RD-H14-060
GYM25LD-H14-060
GYM25RD-H25-060
GYM25LD-H25-060
GYM25RD-H25-060
GYM25LD-H25-060
GYM25RD-H25-060
GYM25LD-H25-060
GYM25RD-H25-060
GYM25LD-H25-060
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
F074
WF
CW
CDX
SPARE PARTS
LF
LH
Fig. D
*1
Wrench
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
GROOVING
Dimensions (mm)
5 pcs.
HBH
LH 2
HBH
LH 2
Holder
HF
Fig. C
HF
XX
A
/D
XN
A
D
LH
Insert selection
R
Seat
Size
H
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
H
4.75mm
5.00mm
Seat
Size
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
4.75mm
RE 0.2
RE 0.4
RE 0.8
5.00mm
RE 0.2
RE 0.4
RE 0.8
5.24mm
Ball shape
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F075
FACE GROOVING

CDX
B
00 type holder
WF
CW
LF
LH
HF
Fig. B
HF
Fig. A
LH 2
LH 2
XX
A
/D
XN
A
D
LH
HF
Fig. F
HF
Fig. E
LH
XX
A
/D
XN
A
D
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
14
Modular
Modular
85 125
Modular
Modular
25 2
4.75
5.00
5.24
Modular
Modular
Modular
Modular
14
Modular
Modular
125 200
Modular
Modular
25 2
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-H14-085
GYM25LD-H14-085
GYM25RD-H14-085
GYM25LD-H14-085
GYM25RD-H14-085
GYM25LD-H14-085
GYM25RD-H14-085
GYM25LD-H14-085
GYM25RD-H25-085
GYM25LD-H25-085
GYM25RD-H25-085
GYM25LD-H25-085
GYM25RD-H25-085
GYM25LD-H25-085
GYM25RD-H25-085
GYM25LD-H25-085
GYM25RD-H14-125
GYM25LD-H14-125
GYM25RD-H14-125
GYM25LD-H14-125
GYM25RD-H14-125
GYM25LD-H14-125
GYM25RD-H14-125
GYM25LD-H14-125
GYM25RD-H25-125
GYM25LD-H25-125
GYM25RD-H25-125
GYM25LD-H25-125
GYM25RD-H25-125
GYM25LD-H25-125
GYM25RD-H25-125
GYM25LD-H25-125
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
*21 The
F076
WF
CW
CDX
SPARE PARTS
LF
LH
Fig. D
*1
Wrench
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
5
5
GROOVING
Dimensions (mm)
5 pcs.
HBH
LH 2
HBH
LH 2
Holder
HF
Fig. C
HF
XX
A
/D
XN
A
D
LH
Insert selection
R
Seat
Size
H
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
H
4.75mm
5.00mm

Seat
Size
L
H
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
4.75mm
RE 0.2
RE 0.4
RE 0.8
5.00mm
RE 0.2
RE 0.4
RE 0.8
5.24mm
Ball shape
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F077
FACE GROOVING

CDX
B
00 type holder
WF
CW
LF
LH
HF
Fig. B
HF
Fig. A
LH 2
LH 2
XX
A
/D
XN
A
D
LH
HF
Fig. F
HF
Fig. E
LH
XX
A
/D
XN
A
D
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
14
Modular
Modular
180 280
Modular
Modular
25 2
4.75
5.00
5.24
Modular
Modular
Modular
Modular
14
Modular
Modular
250 999
Modular
Modular
25 2
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-H14-180
GYM25LD-H14-180
GYM25RD-H14-180
GYM25LD-H14-180
GYM25RD-H14-180
GYM25LD-H14-180
GYM25RD-H14-180
GYM25LD-H14-180
GYM25RD-H25-180
GYM25LD-H25-180
GYM25RD-H25-180
GYM25LD-H25-180
GYM25RD-H25-180
GYM25LD-H25-180
GYM25RD-H25-180
GYM25LD-H25-180
GYM25RD-H14-250
GYM25LD-H14-250
GYM25RD-H14-250
GYM25LD-H14-250
GYM25RD-H14-250
GYM25LD-H14-250
GYM25RD-H14-250
GYM25LD-H14-250
GYM25RD-H25-250
GYM25LD-H25-250
GYM25RD-H25-250
GYM25LD-H25-250
GYM25RD-H25-250
GYM25LD-H25-250
GYM25RD-H25-250
GYM25LD-H25-250
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
*21 The
F078
WF
CW
CDX
SPARE PARTS
LF
LH
Fig. D
*1
Wrench
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
5
5
GROOVING
Dimensions (mm)
5 pcs.
HBH
LH 2
HBH
LH 2
Holder
HF
Fig. C
HF
XX
A
/D
XN
A
D
LH
Insert selection
R
Seat
Size
H
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
H
4.75mm
5.00mm

Seat
Size
L
H
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
4.75mm
RE 0.2
RE 0.4
RE 0.8
5.00mm
RE 0.2
RE 0.4
RE 0.8
5.24mm
Ball shape
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F079
FACE GROOVING

Insert GY2Mooooooooo-MM
CDX
B
00 type holder
WF
CW
LF
LH
HF
Fig. B
HF
Fig. A
LH 2
LH 2
XX
A
/D
XN
A
D
LH
HF
Fig. F
HF
Fig. E
LH
XX
A
/D
XN
A
D
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
50
70
14
Modular
Modular
Modular
Modular
14
Modular
Modular
70 110
Modular
6.00
6.31
6.35
Modular
25 2
Modular
Modular
Modular
Modular
14
Modular
Modular
110 200
Modular
Modular
25 2
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-J14-050
GYM25LD-J14-050
GYM25RD-J14-050
GYM25LD-J14-050
GYM25RD-J14-050
GYM25LD-J14-050
GYM25RD-J14-050
GYM25LD-J14-050
GYM25RD-J14-070
GYM25LD-J14-070
GYM25RD-J14-070
GYM25LD-J14-070
GYM25RD-J14-070
GYM25LD-J14-070
GYM25RD-J14-070
GYM25LD-J14-070
GYM25RD-J25-070
GYM25LD-J25-070
GYM25RD-J25-070
GYM25LD-J25-070
GYM25RD-J25-070
GYM25LD-J25-070
GYM25RD-J25-070
GYM25LD-J25-070
GYM25RD-J14-110
GYM25LD-J14-110
GYM25RD-J14-110
GYM25LD-J14-110
GYM25RD-J14-110
GYM25LD-J14-110
GYM25RD-J14-110
GYM25LD-J14-110
GYM25RD-J25-110
GYM25LD-J25-110
GYM25RD-J25-110
GYM25LD-J25-110
GYM25RD-J25-110
GYM25LD-J25-110
GYM25RD-J25-110
GYM25LD-J25-110
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
A
A
E
E
E
E
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
*21 The
F080
WF
CW
CDX
SPARE PARTS
LF
LH
Fig. D
*1
Wrench
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
60
60
57
57
57
57
57
57
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
5
5
5
5
GROOVING
Dimensions (mm)
5 pcs.
HBH
LH 2
HBH
LH 2
Holder
HF
Fig. C
HF
XX
A
/D
XN
A
D
LH
Insert selection
R
Seat
Size
J
Geometry name
F012
Breaker
GS
GM
GFGS
Seat
GU
Size CW
J
6.00mm
6.35mm

Seat
Size
L
a
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
6.00mm
RE 0.2
RE 0.4
RE 0.8
6.31mm
6.35mm
RE 0.2
RE 0.4
RE 0.8
Ball shape
a
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F081
FACE GROOVING

Insert GY2Mooooooooo-MM
CDX
B
00 type holder
WF
CW
LF
LH
HF
Fig. B
HF
Fig. A
LH 2
LH 2
XX
A
/D
XN
A
D
LH
HF
Fig. F
HF
Fig. E
LH
XX
A
/D
XN
A
D
LH
LH 2
LH 2
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
Modular
Modular
14
Modular
Modular
170 280
Modular
Modular
25 2
6.00
6.31
6.35
Modular
Modular
Modular
Modular
14
Modular
Modular
250 999
Modular
Modular
25 2
Modular
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYHR2020K00-M25R
GYHL2020K00-M25L
GYHR2525M00-M25R
GYHL2525M00-M25L
GYHR3225P00-M25R
GYHL3225P00-M25L
GYHR3232P00-M25R
GYHL3232P00-M25L
GYM25RD-J14-170
GYM25LD-J14-170
GYM25RD-J14-170
GYM25LD-J14-170
GYM25RD-J14-170
GYM25LD-J14-170
GYM25RD-J14-170
GYM25LD-J14-170
GYM25RD-J25-170
GYM25LD-J25-170
GYM25RD-J25-170
GYM25LD-J25-170
GYM25RD-J25-170
GYM25LD-J25-170
GYM25RD-J25-170
GYM25LD-J25-170
GYM25RD-J14-250
GYM25LD-J14-250
GYM25RD-J14-250
GYM25LD-J14-250
GYM25RD-J14-250
GYM25LD-J14-250
GYM25RD-J14-250
GYM25LD-J14-250
GYM25RD-J25-250
GYM25LD-J25-250
GYM25RD-J25-250
GYM25LD-J25-250
GYM25RD-J25-250
GYM25LD-J25-250
GYM25RD-J25-250
GYM25LD-J25-250
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
C
C
A
A
E
E
E
E
D
D
B
B
F
F
F
F
*21 The
F082
WF
CW
CDX
SPARE PARTS
LF
LH
Fig. D
*1
Wrench
TS55
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
LH 2
HF
WF
HBH
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
20
20
25
25
25
25
32
32
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
125
125
150
150
170
170
170
170
136
136
161
161
181
181
181
181
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
39
39
39
39
39
39
39
39
50
50
50
50
50
50
50
50
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
60
60
57
57
57
57
57
57
71
71
68
68
68
68
68
68
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
20
20
25
25
32
32
32
32
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
26
26
28
28
28
28
35
35
5
5
5
5
5
5
5
5
GROOVING
Dimensions (mm)
5 pcs.
HBH
LH 2
HBH
LH 2
Holder
HF
Fig. C
HF
XX
A
/D
XN
A
D
LH
Insert selection
R
Seat
Size
J
Geometry name
F012
Breaker
GS
GM
GFGS
Seat
GU
Size CW
J
6.00mm
6.35mm

Seat
Size
L
J
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
6.00mm
RE 0.2
RE 0.4
RE 0.8
6.31mm
6.35mm
RE 0.2
RE 0.4
RE 0.8
Ball shape
a
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F083
FACE GROOVING

5
90 type holder
CW
CDX
WF
LH
LF
Fig. A
HF
DA
XN
/DA
XX
GROOVING

Seat
Size
CW
DAXN DAXX
50
12
Modular
50
60
12
Modular
75
75 100
100 150
135 200
180 250
40
50
2.39
2.50
2.74
Type
40
60
2.00
2.24
CDX
60
50
60
75
75 100
12
12
12
12
12
12
12
12
12
Modular
Modular
Modular
Modular
Modular
Modular
Modular
Modular
Modular
12
Modular
135 200
12
Modular
180 250
12
Modular
100 150
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYM25LD-D12-040
GYM25RD-D12-040
GYM25LD-D12-050
GYM25RD-D12-050
GYM25LD-D12-060
GYM25RD-D12-060
GYM25LD-D12-075
GYM25RD-D12-075
GYM25LD-D12-100
GYM25RD-D12-100
GYM25LD-D12-135
GYM25RD-D12-135
GYM25LD-D12-180
GYM25RD-D12-180
GYM25LD-E12-040
GYM25RD-E12-040
GYM25LD-E12-050
GYM25RD-E12-050
GYM25LD-E12-060
GYM25RD-E12-060
GYM25LD-E12-075
GYM25RD-E12-075
GYM25LD-E12-100
GYM25RD-E12-100
GYM25LD-E12-135
GYM25RD-E12-135
GYM25LD-E12-180
GYM25RD-E12-180
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
*1 Dimensions shown are when gauge insert is used. If other insert geometries are used then LF, LH and WF values may vary.
F084
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
SPARE PARTS
Holder
GYHR2525M90-M25L
GYHL2525M90-M25R
*1
Wrench
TS55
GY06013M
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
HF
WF
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
53
GROOVING
Dimensions (mm)
5 pcs.
Insert selection
R
Seat
Size
D
E
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
D
E
2.00mm
2.39mm
2.50mm
Seat
Size
D
E
a
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
2.00mm
2.24mm
2.39mm
2.50mm
2.74mm
Ball shape
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F085
FACE GROOVING

5
90 type holder
CW
Fig. A
LH
LF
Fig. B
HF
HF
DA
XN
/DA
XX
CDX
WF
GROOVING

Seat
Size
CW
DAXN DAXX
CDX
Type
35
40
12
Modular
40
50
12
Modular
50
60
Modular
12
Modular
12
60
75
20 2
Modular
Modular
12
75 100
3.00
3.18
3.24
20 2
Modular
Modular
12
100 150
20 2
Modular
Modular
12
135 200
20 2
Modular
Modular
12
180 250
20 2
Modular
12
Modular
225 999
20 2
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYM25LD-F12-035
GYM25RD-F12-035
GYM25LD-F12-040
GYM25RD-F12-040
GYM25LD-F12-050
GYM25RD-F12-050
GYM25LD-F12-060
GYM25RD-F12-060
GYM25LD-F20-060
GYM25RD-F20-060
GYM25LD-F12-075
GYM25RD-F12-075
GYM25LD-F20-075
GYM25RD-F20-075
GYM25LD-F12-100
GYM25RD-F12-100
GYM25LD-F20-100
GYM25RD-F20-100
GYM25LD-F12-135
GYM25RD-F12-135
GYM25LD-F20-135
GYM25RD-F20-135
GYM25LD-F12-180
GYM25RD-F12-180
GYM25LD-F20-180
GYM25RD-F20-180
GYM25LD-F12-225
GYM25RD-F12-225
GYM25LD-F20-225
GYM25RD-F20-225
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
A
A
A
A
A
A
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
Dimensions shown are when gauge insert is used. If other insert geometries are used then LF, LH and WF values may vary.
*21 The
F086
SPARE PARTS
Holder
GYHR2525M90-M25L
GYHL2525M90-M25R
*1
Wrench
TS55
GY06013M
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
HF
WF
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
53
53
53
53
53
53
53
53
59
59
53
53
59
59
53
53
59
59
53
53
59
59
53
53
59
59
53
53
59
59
GROOVING
Dimensions (mm)
5 pcs.
Insert selection
R
Seat
Size
F
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
F
3.00mm
3.18mm

Seat
Size
L
F
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
3.00mm
RE 0.2
RE 0.4
RE 0.8
3.18mm
RE 0.2
RE 0.4
3.24mm
Ball shape
a
a
a
a
a
a
a
a
a : Standard insert with dimensions
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F087
FACE GROOVING

5
90 type holder
CW
Fig. A
LH
LF
Fig. B
HF
HF
DA
XN
/DA
XX
CDX
WF

GROOVING
Seat
Size
CW
DAXN DAXX
CDX
Type
40
50
14
Modular
50
60
14
Modular
Modular
14
60
85
25 2
Modular
Modular
14
85 125
25 2
4.00
4.24
Modular
Modular
14
125 200
25 2
Modular
Modular
14
180 280
25 2
Modular
Modular
14
250 999
25 2
*
*
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYM25LD-G14-040
GYM25RD-G14-040
GYM25LD-G14-050
GYM25RD-G14-050
GYM25LD-G14-060
GYM25RD-G14-060
GYM25LD-G25-060
GYM25RD-G25-060
GYM25LD-G14-085
GYM25RD-G14-085
GYM25LD-G25-085
GYM25RD-G25-085
GYM25LD-G14-125
GYM25RD-G14-125
GYM25LD-G25-125
GYM25RD-G25-125
GYM25LD-G14-180
GYM25RD-G14-180
GYM25LD-G25-180
GYM25RD-G25-180
GYM25LD-G14-250
GYM25RD-G14-250
GYM25LD-G25-250
GYM25RD-G25-250
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
A
A
A
A
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
1 Dimensions shown are when gauge insert is used. If other insert geometries are used then LF, LH and WF values may vary.
F088
SPARE PARTS
Holder
GYHR2525M90-M25L
GYHL2525M90-M25R
*1
Wrench
TS55
GY06013M
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
HF
WF
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
53
53
53
53
53
53
64
64
53
53
64
64
53
53
64
64
53
53
64
64
53
53
64
64
GROOVING
Dimensions (mm)
5 pcs.
Insert selection
R
Seat
Size
G
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
G
4.00mm

Seat
Size
L
G
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
4.00mm
RE 0.2
RE 0.4
RE 0.8
4.24mm
Ball shape
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F089
FACE GROOVING

5
90 type holder
CW
Fig. A
LH
LF
Fig. B
HF
HF
DA
XN
/DA
XX
CDX
WF
GROOVING

Seat
Size
CW
DAXN DAXX
50
60
60
85
CDX
Type
14
Modular
14
Modular
25 2
Modular
Modular
14
85 125
25 2
4.75
5.00
5.24
Modular
Modular
14
125 200
25 2
Modular
Modular
14
180 280
25 2
Modular
Modular
14
250 999
25 2
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYM25LD-H14-050
GYM25RD-H14-050
GYM25LD-H14-060
GYM25RD-H14-060
GYM25LD-H25-060
GYM25RD-H25-060
GYM25LD-H14-085
GYM25RD-H14-085
GYM25LD-H25-085
GYM25RD-H25-085
GYM25LD-H14-125
GYM25RD-H14-125
GYM25LD-H25-125
GYM25RD-H25-125
GYM25LD-H14-180
GYM25RD-H14-180
GYM25LD-H25-180
GYM25RD-H25-180
GYM25LD-H14-250
GYM25RD-H14-250
GYM25LD-H25-250
GYM25RD-H25-250
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
A
A
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
*21 The
F090
SPARE PARTS
Holder
GYHR2525M90-M25L
GYHL2525M90-M25R
*1
Wrench
TS55
GY06013M
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
HF
WF
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
53
53
53
53
64
64
53
53
64
64
53
53
64
64
53
53
64
64
53
53
64
64
GROOVING
Dimensions (mm)
5 pcs.
Insert selection
R
Seat
Size
H
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
H
4.75mm
5.00mm
Seat
Size
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
4.75mm
RE 0.2
RE 0.4
RE 0.8
5.00mm
RE 0.2
RE 0.4
RE 0.8
5.24mm
Ball shape
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F091
FACE GROOVING

5
90 type holder
CW
Fig. A
LH
LF
Fig. B
HF
HF
DA
XN
/DA
XX
CDX
WF
GROOVING

Seat
Size
CW
DAXN DAXX
50
70
CDX
Type
14
Modular
14
Modular
70 110
25 2
Modular
Modular
14
110 200
25 2
6.00
6.31
6.35
Modular
Modular
14
170 280
25 2
Modular
Modular
14
250 999
25 2
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
Modular Blade
Stock
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYHR2525M90-M25L
GYHL2525M90-M25R
GYM25LD-J14-050
GYM25RD-J14-050
GYM25LD-J14-070
GYM25RD-J14-070
GYM25LD-J25-070
GYM25RD-J25-070
GYM25LD-J14-110
GYM25RD-J14-110
GYM25LD-J25-110
GYM25RD-J25-110
GYM25LD-J14-170
GYM25RD-J14-170
GYM25LD-J25-170
GYM25RD-J25-170
GYM25LD-J14-250
GYM25RD-J14-250
GYM25LD-J25-250
GYM25RD-J25-250
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
A
A
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
*21 The
F092
SPARE PARTS
Holder
GYHR2525M90-M25L
GYHL2525M90-M25R
*1
Wrench
TS55
GY06013M
: 6.0Nm)
: 5.0Nm)
zTKY30R
xTKY25D
Cutting Mode
LF
LH
HF
WF
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
53
53
53
53
64
64
53
53
64
64
53
53
64
64
53
53
64
64
GROOVING
Dimensions (mm)
5 pcs.
Insert selection
R
Seat
Size
J
Geometry name
F012
Breaker
GS
GM
GFGS
Seat
GU
Size CW
J
6.00mm
6.35mm
Seat
Size
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
6.00mm
RE 0.2
RE 0.4
RE 0.8
6.31mm
6.35mm
RE 0.2
RE 0.4
RE 0.8
Ball shape
a
a
a
a
a
a
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F110
F112
F093
INTERNAL GROOVING
GYSERIES (INTERNAL GROOVING)

6
90 type holder
aMono block type (Air / coolant through)
WF
90
Fig. A
F2
CDX
DMIN
LDRED
H
DCON
LF
F2
CDX
WF
90
Fig. B
LDRED
LF
GROOVING

Seat
Size
CW
CDX
*3
DMIN
Type
Mono Block
25
Mono Block
6
Mono Block
32
Mono Block
4 9.5
2.00
2.24
5.5 9.5
Modular
*1
40
Modular
Modular
*1
50
Modular
Modular
60
Modular
7 11.5 1
Modular
70
Modular
*
*
*
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
GYAR20K90A-D06
GYAL20K90A-D06
GYAR20Q90A-D06
GYAL20Q90A-D06
GYAR25K90B-D06
GYAL25K90B-D06
GYAR25R90B-D06
GYAL25R90B-D06
GYDR32L90C-M20L
GYDL32L90C-M20R
GYDR32S90C-M20L
GYDL32S90C-M20R
GYDR40M90D-M20L
GYDL40M90D-M20R
GYDR40T90D-M20L
GYDL40T90D-M20R
GYDR40M90D-M25L
GYDL40M90D-M25R
GYDR40T90D-M25L
GYDL40T90D-M25R
GYDR50P90F-M25L
GYDL50P90F-M25R
GYDR50T90F-M25L
GYDL50T90F-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Modular Blade
Stock
GYM20LA-D10
GYM20RA-D10
GYM20LA-D10
GYM20RA-D10
GYM20LA-D10
GYM20RA-D10
GYM20LA-D10
GYM20RA-D10
GYM25LA-D12
GYM25RA-D12
GYM25LA-D12
GYM25RA-D12
GYM25LA-D12
GYM25RA-D12
GYM25LA-D12
GYM25RA-D12
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
B
B
A
A
B
B
A
A
D
D
C
C
D
D
C
C
D
D
C
C
D
D
C
C
1 The maximum groove depth varies according to the cutting diameter DMIN. For details, please refer to page F116.
2 Dimensions shown are when the gauge insert is used. If other insert geometries are used then LF, LDRED, WF and F2 values may vary.
3 The maximum groove depth (CDX) is a value within the dimension LDRED.
F094
Hand
(R/L)
aModular blade type (Air / coolant through)
SPARE PARTS
90
WF
Holder
LDRED
H
DCON
LF
zGY05016S
(Clamp Torque
: 5.0Nm)
GYAR/L25o90B-o06
90
F2
CDX
WF
GYDR/L40o90D-M20L/R
TS407
: 3.5Nm)
: 6.0Nm)
GYDR/L40o90D-M25L/R xGY06013M
LF
*2
Dimensions (mm)
Wrench
GYDR/L50o90F-M25L/R
zTKY20R
GYDR/L32o90C-M20L/R xGY06013M
LDRED
4 pcs.
GYAR/L20o90A-o06
Fig. D
TS55
: 5.0Nm)
: 6.0Nm)
zTKY30R
xTKY15D
zTKY30R
xTKY25D
Cutting Mode
DCON
LF
LDRED
WF
F2
20
20
20
20
25
25
25
25
32
32
32
32
40
40
40
40
40
40
40
40
50
50
50
50
125
125
180
180
125
125
200
200
140
140
250
250
150
150
300
300
150
150
300
300
170
170
300
300
30
30
30
30
40
40
40
40
50
50
50
50
60
60
60
60
60
60
60
60
80
80
80
80
14.5
14.5
14.5
14.5
19
19
19
19
22
22
22
22
28
28
28
28
28
28
28
28
34
34
34
34
4.5
4.5
4.5
4.5
6.5
6.5
6.5
6.5
6
6
6
6
8
8
8
8
8
8
8
8
9
9
9
9
18
18
18
18
23
23
23
23
30
30
30
30
37
37
37
37
37
37
37
37
47
47
47
47
GROOVING
Fig. C
F2
CDX
DMIN
Insert selection
R
Seat
Size
D
Geometry name
F012, F013
Breaker
Seat
GS
GM
GFGS
GU
Size CW
D
2.00mm

Seat
Size
L
D
a
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
2.00mm
2.24mm
Ball nose
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F116
F118
F095
INTERNAL GROOVING

6
90 type holder
WF
90
Fig. A
F2
CDX
DMIN
LDRED
H
DCON
LF
F2
CDX
WF
90
Fig. B
LDRED
LF
GROOVING

Seat
Size
CW
CDX
*3
DMIN
Type
Mono Block
25
Mono Block
6
Mono Block
32
Mono Block
2.39
2.50
2.74
4 9.5
5.5 9.5
Modular
*1
40
Modular
Modular
*1
50
Modular
Modular
60
Modular
7 11.5 1
Modular
70
Modular
*
*
*
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
GYAR20K90A-E06
GYAL20K90A-E06
GYAR20Q90A-E06
GYAL20Q90A-E06
GYAR25K90B-E06
GYAL25K90B-E06
GYAR25R90B-E06
GYAL25R90B-E06
GYDR32L90C-M20L
GYDL32L90C-M20R
GYDR32S90C-M20L
GYDL32S90C-M20R
GYDR40M90D-M20L
GYDL40M90D-M20R
GYDR40T90D-M20L
GYDL40T90D-M20R
GYDR40M90D-M25L
GYDL40M90D-M25R
GYDR40T90D-M25L
GYDL40T90D-M25R
GYDR50P90F-M25L
GYDL50P90F-M25R
GYDR50T90F-M25L
GYDL50T90F-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Modular Blade
Stock
GYM20LA-E10
GYM20RA-E10
GYM20LA-E10
GYM20RA-E10
GYM20LA-E10
GYM20RA-E10
GYM20LA-E10
GYM20RA-E10
GYM25LA-E12
GYM25RA-E12
GYM25LA-E12
GYM25RA-E12
GYM25LA-E12
GYM25RA-E12
GYM25LA-E12
GYM25RA-E12
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
B
B
A
A
B
B
A
A
D
D
C
C
D
D
C
C
D
D
C
C
D
D
C
C
1 The maximum groove depth varies according to the cutting diameter DMIN. For details, please refer to page F116.
2 Dimensions shown are when the gauge insert is used. If other insert geometries are used then LF, LDRED, WF and F2 values may vary.
3 The maximum groove depth (CDX) is a value within the dimension LDRED.
F096
Hand
(R/L)
SPARE PARTS
90
WF
Holder
LDRED
H
DCON
LF
zGY05016S
(Clamp Torque
: 5.0Nm)
GYAR/L25o90B-o06
90
F2
CDX
WF
GYDR/L40o90D-M20L/R
TS407
: 3.5Nm)
: 6.0Nm)
LF
*2
Dimensions (mm)
Wrench
GYDR/L50o90F-M25L/R
zTKY20R
LDRED
4 pcs.
GYAR/L20o90A-o06
Fig. D
TS55
: 5.0Nm)
: 6.0Nm)
zTKY30R
xTKY15D
zTKY30R
xTKY25D
Cutting Mode
DCON
LF
LDRED
WF
F2
20
20
20
20
25
25
25
25
32
32
32
32
40
40
40
40
40
40
40
40
50
50
50
50
125
125
180
180
125
125
200
200
140
140
250
250
150
150
300
300
150
150
300
300
170
170
300
300
30
30
30
30
40
40
40
40
50
50
50
50
60
60
60
60
60
60
60
60
80
80
80
80
14.5
14.5
14.5
14.5
19
19
19
19
22
22
22
22
28
28
28
28
28
28
28
28
34
34
34
34
4.5
4.5
4.5
4.5
6.5
6.5
6.5
6.5
6
6
6
6
8
8
8
8
8
8
8
8
9
9
9
9
18
18
18
18
23
23
23
23
30
30
30
30
37
37
37
37
37
37
37
37
47
47
47
47
GROOVING
Fig. C
F2
CDX
DMIN
Insert selection
R
Seat
Size
E
Geometry name
F012, F013
Breaker
Seat
GS
GM
GFGS
GU
Size CW
E
2.39mm
2.50mm
Seat
Size
E
a
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
2.39mm
2.50mm
2.74mm
Ball nose
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F116
F118
F097
INTERNAL GROOVING

6
90 type holder
WF
90
Fig. A
F2
CDX
DMIN
LDRED
H
DCON
LF
F2
CDX
WF
90
Fig. B
LDRED
LF
GROOVING

Seat
Size
CW
CDX
*3
DMIN
Type
Mono Block
25
Mono Block
6
Mono Block
32
Mono Block
3.00
3.18
3.24
4 9.5
5.5 9.5
Modular
*1
40
Modular
Modular
*1
50
Modular
Modular
60
Modular
7 11.5 1
Modular
70
Modular
Mono Block
32
Mono Block
4.5 11.5 1
4.00
4.24
6 11.5 1
Modular
40
Modular
Modular
50
Modular
Modular
60
7.5 13
Modular
*1
Modular
70
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
GYAR20K90A-F06
GYAL20K90A-F06
GYAR20Q90A-F06
GYAL20Q90A-F06
GYAR25K90B-F06
GYAL25K90B-F06
GYAR25R90B-F06
GYAL25R90B-F06
GYDR32L90C-M20L
GYDL32L90C-M20R
GYDR32S90C-M20L
GYDL32S90C-M20R
GYDR40M90D-M20L
GYDL40M90D-M20R
GYDR40T90D-M20L
GYDL40T90D-M20R
GYDR40M90D-M25L
GYDL40M90D-M25R
GYDR40T90D-M25L
GYDL40T90D-M25R
GYDR50P90F-M25L
GYDL50P90F-M25R
GYDR50T90F-M25L
GYDL50T90F-M25R
GYAR25K90B-G07
GYAL25K90B-G07
GYAR25R90B-G07
GYAL25R90B-G07
GYDR32L90C-M20L
GYDL32L90C-M20R
GYDR32S90C-M20L
GYDL32S90C-M20R
GYDR40M90D-M20L
GYDL40M90D-M20R
GYDR40T90D-M20L
GYDL40T90D-M20R
GYDR40M90D-M25L
GYDL40M90D-M25R
GYDR40T90D-M25L
GYDL40T90D-M25R
GYDR50P90F-M25L
GYDL50P90F-M25R
GYDR50T90F-M25L
GYDL50T90F-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Modular Blade
Stock
GYM20LA-F10
GYM20RA-F10
GYM20LA-F10
GYM20RA-F10
GYM20LA-F10
GYM20RA-F10
GYM20LA-F10
GYM20RA-F10
GYM25LA-F12
GYM25RA-F12
GYM25LA-F12
GYM25RA-F12
GYM25LA-F12
GYM25RA-F12
GYM25LA-F12
GYM25RA-F12
GYM20LA-G12
GYM20RA-G12
GYM20LA-G12
GYM20RA-G12
GYM20LA-G12
GYM20RA-G12
GYM20LA-G12
GYM20RA-G12
GYM25LA-G14
GYM25RA-G14
GYM25LA-G14
GYM25RA-G14
GYM25LA-G14
GYM25RA-G14
GYM25LA-G14
GYM25RA-G14
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
B
B
A
A
B
B
A
A
D
D
C
C
D
D
C
C
D
D
C
C
D
D
C
C
B
B
A
A
D
D
C
C
D
D
C
C
D
D
C
C
D
D
C
C
maximum groove depth varies according to the cutting diameter DMIN. For details, please refer to page F116.
*12 The
Dimensions shown are when the gauge insert is used. If other insert geometries are used then LF, LDRED, WF and F2 values may vary.
*3 The maximum groove depth (CDX) is a value within the dimension LDRED.
*
F098
SPARE PARTS
90
WF
Holder
LDRED
H
DCON
LF
zGY05016S
(Clamp Torque
: 5.0Nm)
GYAR/L25o90B-ooo
90
F2
CDX
WF
GYDR/L40o90D-M20L/R
TS407
: 3.5Nm)
: 6.0Nm)
LF
*2
Dimensions (mm)
Wrench
GYDR/L50o90F-M25L/R
zTKY20R
LDRED
4 pcs.
GYAR/L20o90A-F06
Fig. D
TS55
: 5.0Nm)
: 6.0Nm)
zTKY30R
xTKY15D
zTKY30R
xTKY25D
Cutting Mode
DCON
LF
LDRED
WF
F2
20
20
20
20
25
25
25
25
32
32
32
32
40
40
40
40
40
40
40
40
50
50
50
50
25
25
25
25
32
32
32
32
40
40
40
40
40
40
40
40
50
50
50
50
125
125
180
180
125
125
200
200
140
140
250
250
150
150
300
300
150
150
300
300
170
170
300
300
125
125
200
200
140
140
250
250
150
150
300
300
150
150
300
300
170
170
300
300
30
30
30
30
40
40
40
40
50
50
50
50
60
60
60
60
60
60
60
60
80
80
80
80
40
40
40
40
50
50
50
50
60
60
60
60
60
60
60
60
80
80
80
80
14.5
14.5
14.5
14.5
19
19
19
19
22
22
22
22
28
28
28
28
28
28
28
28
34
34
34
34
19
19
19
19
22
22
22
22
28
28
28
28
28
28
28
28
34
34
34
34
4.5
4.5
4.5
4.5
6.5
6.5
6.5
6.5
6
6
6
6
8
8
8
8
8
8
8
8
9
9
9
9
6.5
6.5
6.5
6.5
6
6
6
6
8
8
8
8
8
8
8
8
9
9
9
9
18
18
18
18
23
23
23
23
30
30
30
30
37
37
37
37
37
37
37
37
47
47
47
47
23
23
23
23
30
30
30
30
37
37
37
37
37
37
37
37
47
47
47
47
GROOVING
Fig. C
F2
CDX
DMIN
Insert selection
R
Seat
Size
F
Geometry name
F012, F013
Breaker
Seat
GS
GM
GFGS
GU
Size CW
F
3.00mm
3.18mm

Seat
Size
Seat
Size
G
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
3.00mm
RE 0.2
RE 0.4
RE 0.8
3.18mm
RE 0.2
RE 0.4
3.24mm
Ball nose
a
a
a
a
a
a
a
a
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
G
4.00mm

Seat
Size
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
4.00mm
RE 0.2
RE 0.4
RE 0.8
4.24mm
Ball nose
a
a
IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F116
F118
F099
INTERNAL GROOVING

6
90 type holder
WF
90
Fig. A
F2
CDX
DMIN
LDRED
H
DCON
LF
F2
CDX
WF
90
Fig. B
LDRED
LF
GROOVING

Seat
Size
CW
CDX
*3
DMIN
Type
Mono Block
32
Mono Block
4.5 11.5 1
4.75
5.00
5.24
6 11.5 1
Modular
40
Modular
Modular
50
Modular
Modular
60
7.5 13
Modular
*1
Modular
70
Modular
Modular
60
7.5 13
Modular
*1
Modular
70
Modular
Hand
(R/L)
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
Order Number
Fig.
Holder
Stock
GYAR25K90B-H07
GYAL25K90B-H07
GYAR25R90B-H07
GYAL25R90B-H07
GYDR32L90C-M20L
GYDL32L90C-M20R
GYDR32S90C-M20L
GYDL32S90C-M20R
GYDR40M90D-M20L
GYDL40M90D-M20R
GYDR40T90D-M20L
GYDL40T90D-M20R
GYDR40M90D-M25L
GYDL40M90D-M25R
GYDR40T90D-M25L
GYDL40T90D-M25R
GYDR50P90F-M25L
GYDL50P90F-M25R
GYDR50T90F-M25L
GYDL50T90F-M25R
GYDR40M90D-M25L
GYDL40M90D-M25R
GYDR40T90D-M25L
GYDL40T90D-M25R
GYDR50P90F-M25L
GYDL50P90F-M25R
GYDR50T90F-M25L
GYDL50T90F-M25R
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Modular Blade
Stock
GYM20LA-H12
GYM20RA-H12
GYM20LA-H12
GYM20RA-H12
GYM20LA-H12
GYM20RA-H12
GYM20LA-H12
GYM20RA-H12
GYM25LA-H14
GYM25RA-H14
GYM25LA-H14
GYM25RA-H14
GYM25LA-H14
GYM25RA-H14
GYM25LA-H14
GYM25RA-H14
GYM25LA-J14
GYM25RA-J14
GYM25LA-J14
GYM25RA-J14
GYM25LA-J14
GYM25RA-J14
GYM25LA-J14
GYM25RA-J14
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
B
B
A
A
D
D
C
C
D
D
C
C
D
D
C
C
D
D
C
C
D
D
C
C
D
D
C
C
6.00
6.31
6.35
maximum groove depth varies according to the cutting diameter DMIN. For details, please refer to page F116.
*12 The
Dimensions shown are when the gauge insert is used. If other insert geometries are used then LF, LDRED, WF and F2 values may vary.
*3 The maximum groove depth (CDX) is a value within the dimension LDRED.
*
F100
SPARE PARTS
90
WF
Holder
LDRED
H
DCON
LF
90
zGY05016S
(Clamp Torque
: 5.0Nm)
F2
CDX
WF
GYDR/L40o90D-M20L/R
TS407
: 3.5Nm)
: 6.0Nm)
LF
*2
Dimensions (mm)
Wrench
GYDR/L50o90F-M25L/R
zTKY20R
LDRED
4 pcs.
GYAR/L25o90B-o07
Fig. D
TS55
: 5.0Nm)
: 6.0Nm)
zTKY30R
xTKY15D
zTKY30R
xTKY25D
Cutting Mode
DCON
LF
LDRED
WF
F2
25
25
25
25
32
32
32
32
40
40
40
40
40
40
40
40
50
50
50
50
40
40
40
40
50
50
50
50
125
125
200
200
140
140
250
250
150
150
300
300
150
150
300
300
170
170
300
300
150
150
300
300
170
170
300
300
40
40
40
40
50
50
50
50
60
60
60
60
60
60
60
60
80
80
80
80
60
60
60
60
80
80
80
80
19
19
19
19
22
22
22
22
28
28
28
28
28
28
28
28
34
34
34
34
28
28
28
28
34
34
34
34
6.5
6.5
6.5
6.5
6
6
6
6
8
8
8
8
8
8
8
8
9
9
9
9
8
8
8
8
9
9
9
9
23
23
23
23
30
30
30
30
37
37
37
37
37
37
37
37
47
47
47
47
37
37
37
37
47
47
47
47
GROOVING
Fig. C
F2
CDX
DMIN
Insert selection
R
Seat
Size
H
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
H
4.75mm
5.00mm

Seat
Size
Seat
Size
J
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
4.75mm
RE 0.2
RE 0.4
RE 0.8
5.00mm
RE 0.2
RE 0.4
RE 0.8
5.24mm
Ball nose
a
a
a
a
a
a
a
Geometry name
F012, F013
Breaker
GS
GM
GFGS
Seat
GU
Size CW
J
6.00mm
6.35mm

Seat
Size
Breaker
MF
(Finish)
F013, F014
MS
MM
BM
CW
6.00mm
RE 0.2
RE 0.4
RE 0.8
6.31mm
6.35mm
RE 0.2
RE 0.4
RE 0.8
Ball nose
a
a
a
a
a
a
a
a

IDENTIFICATION
CUTTING CONDITIONS
CAUTION FOR USE
F010, F011
F116
F118
F101
EXTERNAL GROOVING
RECOMMENDED CUTTING SPEED (m/min) [For External Grooving]
Work Material
Hardness
Grade
50
100
VP20RT
P
< 160HB
Mild Steel
VP20RT
180
90
VP20RT
170
60
140
70
VP10RT
150
90
MY5015
GROOVING
VP20RT
< 270HB
135
60
140
70
VP10RT
VP20RT
Tensile Strength
< 300MPa
Gray Cast Iron
210
55
NX2525
Stainless Steel
250
70
NX2525
190
110
MY5015
280HB<
210
80
VP10RT
Carbon Steel
Alloy Steel
230
90
NX2525
150
80
180
90
VP10RT
190
140
MY5015
VP20RT
Tensile Strength
< 800MPa
Ductile Cast Iron
60
150
90
MY5015
30
VP20RT
Titanium Alloy
50HRC<
Hardened steel
300
140
70
VP10RT
300
250
220
110
VP10RT
160280HB

150
200
100
210
60
VP10RT
40
70
RT9010
40
70
80
MB8025
120
(Note 1) VP20RT is the first recommended grade for materials other than hardened steel.
(Note 2) For VP10RT, VP20RT and MY5015, wet cutting is recommended.
RECOMMENDED CUTTING CONDITIONS [For External Grooving]
*Recommended cutting conditions when combining a GYHR/L2525M00/90-M24R\L modular holder and GYM25R/LA-ooo modular blade.
y Recommended feed rate and depth of cut
GU BREAKER
GS BREAKER
J
H
G
F
E
D
0 0.03
0.1
Feed (mm/rev)
0.2
K
J
H
G
F
E
D
C
0.1
0.3
0.4
1.50
2.00
2.24
2.39
2.50
2.74
3.00
3.18
3.24
4.00
4.24
4.75
5.00
5.24
6.00
6.31
6.35
8.00
F
G
a Grooving
H
J
K
Seat size
Seat size
0.2
Feed (mm/rev)
aGrooving, Cutting off
F102
FLAT TOP GFGS (CBN)
K
J
H
G
F
E
D
C
Seat Size
Insert Width (mm)
GM BREAKER
: 1st recommended area
Seat size
Seat size
0.1
0.2
Feed (mm/rev)
0.3
0.4
H
G
F
E
D
0.05
0.1
Feed (mm/rev)
0.15
MF BREAKER
a Turning
Seat size
: 1st
recommended area
J
H
G
F
E
D
0
0.05
0.1
Feed (mm/rev)
0.15
Seat Size
Radial Depth of cut (mm)
a Grooving
0.2
Seat size
J
3.0
Insert Width (mm)
2.5
2.0
1.5
1.0
0.5
0
0.05
0.1
Feed (mm/rev)
0.15
0.2
G
H
MS BREAKER
0.1
0.2
Feed (mm/rev)
0.3
0.4
Seat size
K
4.0
3.0
2.0
1.0
H
G
F
0.1
0.2
Feed (mm/rev)
0.3
0.4
0.3
0.4
GROOVING
Seat size
: 1st
recommended area
K
J
H
G
F
E
D
J
a Turning
a Grooving
2.00
2.24
2.39
2.50
2.74
3.00
3.18
3.24
4.00
4.24
4.75
5.00
5.24
6.00
6.31
6.35
8.00
a Turning
Seat size
a Grooving
: 1st
recommended area
K
J
H
G
F
E
D
0
0.1
0.2
Feed (mm/rev)
0.3
MM BREAKER
0.4
Seat size
K
4.0
3.0
J
H
F G
2.0
D E
1.0
0
0.1
0.2
Feed (mm/rev)
a Turning
Seat size
a Grooving
: 1st
recommended area
K
J
H
G
F
E
D
0
0.1
0.2
Feed (mm/rev)
0.3
0.4
BM BREAKER
Seat size
K
3.0
H J
G
F
2.0
1.0
E
D
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Feed (mm/rev)
(Note) Lower the recommended cutting speed given in the table by 20% and 40% respectively when combining the following modular holders and modular blades.
GYHR2020K00-M20R
GYM20
(20mm20mm Square holder)
GYM20
GYHR1616J00-M20R
16mm
GYHR2020K00-M25R
20mm
GYM25
a Decrease the feed rate by 40%.
20mm
a Decrease the feed rate by 20%.
(16mm16mm Square holder)
y In the case of mono block type holder for Swiss style lathes
r 20 12
100%
r 16 16
80%
r 12 12
60%
r 10 10
50%
0.1
Please refer to the tables above on recommended cutting conditions for

external grooving.
Apply the percentage ratio shown on each shank size with the values in
the table.
0.2
Recommended maximum feed
F103
EXTERNAL GROOVING
LIMITATION OF THE MAXIMUM GROOVE DEPTH [For External Grooving]
Max. Groove Depth

CDX
CDX 2
When using the modular blade GYMiiR/LA- iii

The maximum groove depth is not limited by the workpiece diameter.
When using the modular blade GYMiiR/LB- iii

The maximum groove depth is limited by the workpiece diameter.
Max. Groove Depth (mm)
19
ce
ie r
kp te
or ame
W Di
18
17
16
GYM20R/LB-D18
GYM20R/LB-E18
GYM20R/LB-F18
15
14
0 36 40
48
70
Due to the interference on

this part, the maximum groove
depth is limited by the workpiece diameter.
137
GROOVING
Workpiece Diameter (mm)
In the case of mono block type holder for Swiss style lathes
The maximum groove depth is limited by the workpiece diameter.
Max. Groove Depth
CDX
CDX 2
ce
ie r
kp te
or ame
W Di
Due to interference, the maximum groove depth is limited by

the workpiece diameter.
13
11
12
11
10
8
7
6
5
4
3
9
8
7
6
5
4
3
GYSR/L1010JX00-o11
10
GYSR/L1212JX00-o13
1
0
22
24
32
57
103
26
30
43
16
15
14
13
12
11
10
9
8
GYSR/L1616JX00-o17
6
5
0
34
37
44
60
107
F104
96
288
17
59
286
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
GYSR/L2012JX00-o18
36
38
45
63
97
239
RECOMMENDED CUTTING SPEED (m/min) [For External Recessing]

Hardness
Mild Steel
< 180HB
Grade

100
150
50
80
VP20RT
Carbon Steel
Alloy Steel
180 280HB
90
< 350HB
Stainless Steel
K
Tensile Strength
< 350MPa
Gray Cast Iron
135
110
60
VP10RT
120
80
MY5015
45
VP20RT
110
VP10RT
60
VP20RT
60
120
140
70
VP10RT
150
90
VP20RT
Ductile Cast Iron
50
60
VP10RT
VP20RT
30
70
60
40
VP10RT
160
60
40
VP10RT
120
80
30
VP20RT
Titanium Alloy
210
110
MY5015
160
105
50
MY5015
Tensile Strength
< 800MPa
210
55
50
NX2525
150
MY5015
VP20RT
280 350HB
140
70
VP10RT
NX2525
Carbon Steel
Alloy Steel
190
60
VP20RT
250
180
90
VP10RT
200
GROOVING
Work Material
70
APMX 2
DISTANCE FROM WORK SURFACE TO RECESS DEPTH
AP
APMX 2
Grooving Width Recess depth Distance from work surface to recess depth
CW (mm)
APMX (mm)
APMX 2 (mm)
2.00
2.50
3.00
3.18
4.00
4.75
5.00
6.00
6.35
1.50
1.75
2.00
2.09
2.50
2.88
3.00
3.50
3.68
0.646
0.720
0.793
0.819
0.939
1.049
1.086
1.232
1.283
BM BREAKER
Minimum grooving diameter
Ensure the tool is suitable for the diameter being machined. Refer to the Min. Grooving Diameter D1 as shown in the table on the page
number to avoid a collision with the workpiece shown below.
Min. Grooving
Diameter
y Recommended feed rate and depth of cut

aFor recessing
J
1st
Recommendation
Seat size
H
G
F
E
D
0
0.05
0.1
0.15
0.2
Feed (mm/rev)
0.25
F105
EXTERNAL GROOVING
TOOL SELECTION
a Notes when selecting the tool body
Modular Blade
20mm
GYHR2020K00-M25R
GYHR2020K00-M20R
GYM25
Modular holder
GYM25
GYHR2020K00-M25R
20mm
GYHR2525M00-M25R
25mm
GYM25
20mm
Modular blade (1)
Precautions when selecting a modular holder.
GYM20
aSelect a modular holder with the largest possible shank size
to maintain mounting rigidity.
aIf there is no restriction for use, select the largest modular
blade for the same shank size.
Modular blade (2)

GROOVING
Modular blade (3)
aSelect the shortest possible blade
suitable for the application.
aSelect the shortest possible blade suitable for the application.
a Notes when setting the tool

Setting of cutting edge height
Tool body setting angle
90
<Grooving/Cross-feed machining>
Set the cutting edge height to 0.1mm parallel to the central axis.
<Cutting off>
Set the cutting edge height to 0+0.2mm parallel to the central axis.
90
aSet the insert perpendicular to the central axis.
Overhang
aWhen setting the tool, ensure that the overhang is as short as possible and avoid the step difference part as above figure shows.
F106
MACHINING RECOMMENDATIONS
a Notes on multi-functional machining (MF,MS,MM and BM breakers)

Machining narrow grooves
Machining wide grooves
xcz
aIt is recommended to carry out plunging in several passes.
Following the steps above makes it difficult for chips to elongate.

This also improves the accuracy of workpiece wall surface.
aIt is recommended that cross-feed machining is used.
FINISHING
GROOVING
ROUGHING
z Carry out grooving.

x Retract the tool approx
0.1mm.
c Carry out cross feed

machining.
vRetract the tool approx
0.1mm.
b Carry out grooving.

m Carry out grooving to
n Retract the tool approx
the end point of the
0.1mm.
corner radius.
* Repeat the steps z n.
, Machining of the wall

surface, corner radius and
bottom face should be
carried out in one process.
Precautions when finishing walls
FINISHING
.
/
.Stop at the bottom of

the corner radius.
/ Machine the counter

wall to the corner
radius in one process.
Finish machining.
Wall machining
aWhen machining a wall, chip jamming can occur. In this case, stop
cross feed machining just before the wall (at a point less than the
insert width) then remove the remaining material by plunging.
aTo produce high accuracy walls using MS or MM
breaker insert, do not carry out back turning.

Plunging is recommended.
Machining of a ring section
aWhen a ring remains in a cross feed end process, finish
cross feed machining 1 1.5mm short of the end point,

then remove the ring by plunging.
F107
EXTERNAL GROOVING
a Notes on multi-functional machining (BM breaker)

Copying
Roughing
APMX
aWith the BM breaker insert, 3 dimensional copying is possible.
Set the depth of cut (APMX) to 40% less than the insert width.
aUse plunging and cross-feed machining.
When machining the corner, vibration is likely to occur.

To avoid this, reduce the feed by 50%.
GROOVING
Finishing
APMX 2
aCarry out finishing in one process.
For the depth of cut (APMX 2) when back turning, refer to the table on the right.
Insert
GY2M0200D100N-BM
GY2M0250E125N-BM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY2M0400G200N-BM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY2M0600J300N-BM
GY2M0635J318N-BM
GY2M0800K400N-BM
APMX 2 (mm)
0.05
0.10
0.15
0.20
0.24
0.30
0.40
a Notes for cutting off

Feed
<Feed>
Revolution
Distance from the cutting edge

to the workpiece centre
<Spindle speed>
&D
&D
Feed f
Maximum spindle speed Revolution n
max-n
0.8x(max-n)
1.0xf
0.5xf
Distance a
Distance from the cutting edge

to the workpiece centre
start-n
Distance a
0 0.2xD 0.5xD
aWhen the cutting edge approaches the centre, reduce the
feed by 50%.
0.5xD
aWhen using constant cutting speed during a cutting off cycle,
it is recommended to limit the spindle speed to 80% of

maximum to ensure stability.
aIf necessary, stop the feed prior to reaching the centre of the
workpiece to prevent it falling under its own weight.
aTo prevent the workpiece from being expelled, lower the
spindle speed before finishing the grooving operation.
Insert
Neutral insert
Handed insert
Neutral insert
Handed insert
aWhen there is a centre stub on solid bar work or burrs are formed on pipe material, it is possible to decrease them by using a handed insert.
With a handed insert, machining tends to be less stable when compared to using a neutral insert.
Pay special attention to avoid fracturing of the cutting edge and decrease the feed when necessary.
F108
Memo
F109
FACE GROOVING
RELATIONSHIP BETWEEN THE MODULAR BLADE AND FEED PER ROTATION [For Face Grooving]
100
GYM25R/LD-G14-ooo
GYM25R/LD-H14-ooo
Feed (%)
90
GYM25R/LD-D12-ooo GYM25R/LD-J14-ooo
GYM25R/LD-E12-ooo
GYM25R/LD-F12-ooo
80
70
GYM25R/LD-F20-ooo
GYM25R/LD-G25-ooo
GYM25R/LD-H25-ooo
GYM25R/LD-J25-ooo
60
50
40
35
60
85
125
180
250
Modular Blade (-ooo)
GROOVING
(Note) Adjust the feed per rotation in the cutting conditions to the percentage shown in the table above.
RECOMMENDED CUTTING SPEED (m/min) [For Face Grooving]

Work Material
Hardness
Grade
50
80
VP20RT
P
Mild Steel
< 160HB
170
60
140
70
VP10RT
150
90
MY5015
135
50
VP20RT
110
60
VP10RT
120
80
MY5015
45
NX2525
M
Stainless Steel
< 270HB
K
Gray Cast Iron
Tensile Strength
< 300MPa
VP20RT
50
110
VP10RT
60
VP20RT
60
120
140
70
VP10RT
150
50
110
60
VP10RT
VP20RT
Titanium Alloy
Hardened steel
50HRC<
30
60
VP10RT
40
70
RT9010
40
70
MB8025
120
80
MY5015
210
90
VP20RT
Ductile Cast Iron
160
105
MY5015
Tensile Strength
< 800MPa
210
55
NX2525
280HB<
190
70
VP20RT
Carbon Steel
Alloy Steel
180
90
VP10RT
NX2525
160280HB

150
200
100
60
100
F110
160
250
300
RECOMMENDED CUTTING CONDITIONS [For Face Grooving]

GROOVING
a G : Grounded (GY G-)
Seat size
Seat size
a M : Ungrounded (GY M-)
G
F
E
G
F
E
D
0.05
0.1
0.15
Feed (mm/rev)
0.2
0.05
0.1
Feed (mm/rev)
0.15
PLUNGING
G
F
E
D
GROOVING
a G : Grounded (GY G-)
Seat size
Seat size
a M : Ungrounded (GY M-)
G
F
E
D
0.05
0.1
0.15
Feed (mm/rev)
0.2
0.05
0.1
Feed (mm/rev)
0.15
After the 1st plunge, the width of cut should be

* set
narrower than insert with CW.
TRAVERSE MACHINING (MF BREAKER)

3.0
Seat Size
Seat size
J
2.5
H
2.0
1.5
1.0
0.5
0.05
0.1
Seat Size
Insert Width (mm)

Insert Width (mm)
2.00
4.00
D
G
2.24
4.24
2.39
4.75
E
2.50
H
5.00
2.74
5.24
3.00
6.00
F
3.18
J
6.31
3.24
6.35
0.15
0.2
Feed (mm/rev)
TRAVERSE MACHINING (MM/MS BREAKER)

Axial Depth of Cut (mm)
3.0
Seat size
J
H
2.0
G
F
1.0
E
D
0.1
0.2
0.3
Feed (mm/rev)
TRAVERSE MACHINING (BM BREAKER)

Axial Depth of Cut (mm)
3.0
Seat size
J
2.0
H
G
1.0
0.2
0.4
0.6
Feed (mm/rev)
F111
FACE GROOVING
TOOL SELECTION

Modular blade (1)
Modular blade (2)
a Select a modular blade for
face grooving, so that the

cutting diameter at the first
pass is within the range of
DAXN minimum and DAXX
maximum that are described
in the table of dimensions.
DAXX (Max.)
DAXN (Min.)
aSelect the shortest possible blade suitable for the application.
Modular blade (3)

GROOVING
The maximum cutting diameter
a Select the largest size blade within
the maximum cutting diameter of the

workpiece.
a Machine from the outer diameter
towards the centre.
x
a Increased machining stability and
rigidity is possible if a modular blade

with the largest possible back metal is
used.
a At first machine the
maximum cutting
diameter, there is
no restriction in the
cutting diameter
on the remaining
process.
aWhen plunging in several passes.
aWhen combining plunging and infeed machining.
GYHR2525M00-M25R
Modular holder
GYHR2020K00-M25R
GYM25
Modular holder
aSelect a modular holder with the largest possible shank size to maintain mounting rigidity.
F112
20mm
GYM25
25mm
Precautions when selecting a modular holder.

Setting the cutting edge height
When intertering the wall of groove and the Modular blade
aSet the cutting edge height to 0.1mm parallel to the central axis.
aIf interference occurs even when the correct blade is used,
machining towards the centre with a very small depth of cut

and ensure that an even surface and no material remains at
the centre point afterwards.
the cutting edge height could be incorrect.

When interference occurs on the inner side of the blade,
the cutting edge height is set too high.
When interference occurs on the outer side of the blade,
the cutting edge height is set too low.
Setting the tool
Tool overhang
Parallel
GROOVING
aCutting edge centre height check should be done by traverse
Parallel
aSet the insert parallel to the central axis.
aWhen setting the tool, ensure that the overhang is as short as
possible and avoid the step difference part as above figure

shows.
a Notes when face grooving

aAlways machine from the outer diameter towards the centre.
Machining narrow grooves
z
x
c
aPlunging in several passes is recommended.
aCross feed machining is recommended.
F113
FACE GROOVING
a Notes when face grooving (2)

Notes on the first pass (1)
aDuring the first face grooving pass it is difficult to disperse broken chips and can lead to problems such as a chipped insert.
Maintain longer chips that disperse easily by decreasing the feed per rotation.
GROOVING
Notes on the first pass (2)
aWhen chips become too long, use peck feed to break them into a suitable length.
APM
Notes when wide face grooving by plunging in several passes
aWhen machining a face groove in several passes, machine from the outer diameter towards the centre so that space for discharging
chips is created to prevent insert damage caused by chip jamming.
aPlunging width of cut is recommended to be set at 60 - 80% of the insert width. This enhances the effect of the chipbreaker by
enlarging the width of the groove to improve chip dispersal.
Notes when wide face grooving by combination of plunging and traverse machining (1)
APMX2
APMX3
aWhen face groove machining by using plunge feed and traverse machining, always machine from the outer diameter towards the
centre to disperse chips outward to avoid chip jamming problems.
aSet the depth of cut within 40% of the insert width.
F114
Notes when wide face grooving by combination of plunging and traverse machining (2)
z
aWhen infeed machining at the bottom of a deep groove, chips may interfere on the cutting edge near the centre wall.
GROOVING
In such cases, stop infeed machining just before the centre wall (at a point less than the insert width) then remove the remaining
material by plunging.
Notes when copying (BM Breaker)
APMX 2
aWith the BM breaker insert, 3 dimensional copying is possible. Set the depth of cut (APMX 2) to 30% less than the insert width.
Finishing (1)
z
aWhen finish cutting, machine continuously from the outer wall to the bottom of the groove, then finally plunge cut the centre wall.
Finishing (2) (BM Breaker)

z
aCarry out finishing in one process.
APMX 2
For the depth of cut (APMX 2) when back turning, refer to the table
on the right.
Insert
GY2M0200D100N-BM
GY2M0250E125N-BM
GY2M0300F150N-BM
GY2M0318F159N-BM
GY2M0400G200N-BM
GY2M0475H238N-BM
GY2M0500H250N-BM
GY2M0600J300N-BM
GY2M0635J318N-BM
APMX 2 (mm)
0.10
0.15
0.20
0.25
F115
INTERNAL GROOVING
LIMITATION OF THE MAXIMUM GROOVE DEPTH [For Internal Grooving]
When using the mono block type
The maximum groove depth is not limited by the cutting diameter.
Due to interference of this part,
the maximum groove depth is
limited by the cutting diameter.
When using the modular blade type

The maximum groove depth is limited by the cutting diameter.
Shank Diameter=40mm (GYM20 Blade)
GYM20L/RA-G12
GYM20L/RA-H12
GYM20L/RA-D10
GYM20L/RA-E10
GYM20L/RA-F10
40 44
41 48
55
65
80
90
105
12
11.5
11
12
11.5
11
10
9
8
7
6
5
4.5
4
9
8
6
5.5
5
50 56
54
GROOVING
GYM25L/RA-G14
GYM25L/RA-H14
GYM25L/RA-J14
GYM25L/RA-D12
GYM25L/RA-E12
GYM25L/RA-F12
62
69
80
95
65
80
100
110
130
60
GYM20L/RA-D10
GYM20L/RA-E10
GYM20L/RA-F10
14
13
12
11.5
11
10
9
8
7.5
7
GYM20L/RA-G12
GYM20L/RA-H12
10
125 135
14
13
12
11.5
11
10
9
8
7.5
7
GYM25L/RA-G14
GYM25L/RA-H14
GYM25L/RA-J14
GYM25L/RA-D12
GYM25L/RA-E12
GYM25L/RA-F12
70 80
95 100 115 125
75 85
160
RECOMMENDED CUTTING SPEED (m/min) [For Internal Grooving]

Work Material
Hardness
Grade
50
100
VP20RT
P
Mild Steel
Mild Steel
< 160HB
< 160HB
80
VP20RT
VP10RT
280HB<
M
K
K
Stainless Steel
< 270HB
Stainless Steel
< 270HB
Gray Cast Iron

Gray Cast Iron
Tensile Strength
< 300MPa
Tensile Strength
< 300MPa
90
Ductile Cast Iron

Ductile Cast Iron
S
S
Hardened steel
50HRC<
135
50
110
60
VP20RT
VP10RT
120
80
MY5015
VP10RT
45
110
VP20RT
VP10RT
60
VP20RT
VP10RT
60
120
140
70
VP20RT
VP10RT
150
210
90
MY5015
VP10RT
50
110
60
VP20RT
VP10RT
120
80
MY5015
VP10RT
30
60
VP20RT
VP10RT
40
70
RT9010
VP10RT
40
70
MB8025
160
105
50
VP20RT
NX2525
VP20RT
MY5015
Titanium
Alloy
Heat
Resistant
Alloy
Titanium Alloy
210
55
VP20RT
MY5015
Tensile Strength
< 800MPa
Tensile Strength
< 800MPa
150
MY5015
VP10RT
NX2525
MY5015
140
70
VP20RT
NX2525
280HB<
170
60
NX2525
MY5015
Carbon Steel
Alloy Steel
Carbon Steel
Alloy Steel
190
70
VP20RT
NX2525
160280HB
180
90
VP10RT
NX2525
MY5015
160280HB

150
200
60
100
F116
160
250
300
RECOMMENDED CUTTING CONDITIONS [For Internal Grooving]
105
: 1st
recommended area
50
(Note 1) The cutting diameter 100% represents the minimum cutting diameter (DMIN).
(Note 2) The graph on the left shows the cutting conditions when setting the feed to 100%.
100
40
Feed (%)
Shank Diameter DCON (mm)
GROOVING
32
25
95
90
85
20
0.05
0.1
0.15
80
100
0.2
150
200
250
Hole diameter (%)
Feed (mm/rev)
3.5
a When traverse machining a blind hole, it is recommended to

carry out back turning considering chip disposal.
Seat size
J
3.0
H
2.5
G
2.0
GROOVING
TRAVERSE MACHINING (MF BREAKER)
1.5
1.0
0.5
0
0.05
0.1
0.15
0.2
Feed (mm/rev)
TRAVERSE MACHINING (MM/MS BREAKER)

a When traverse machining a blind hole, it is recommended to
carry out back turning considering chip disposal.
4.0
Seat size
J
3.0
H
G
2.0
F
E
1.0
D
0
0.1
0.2
0.3
Feed (mm/rev)
(Note) The above cutting conditions are for when using the tool overhang (LU) 1.6-2.0 times larger than the shank diameter (DCON). (L/D=1.6-2.0)
When using L/D larger than 2.0, reduce the cutting conditions.
Tool chuck
D
E
F
G
H
J
DCON
Seat Size
Insert Width (mm)
2.00
2.24
2.39
2.50
2.74
3.00
3.18
3.24
4.00
4.24
4.75
5.00
5.24
6.00
6.31
6.35
LU
F117
INTERNAL GROOVING
TOOL SELECTION

Holder
Tool chuck
Tool chuck
aWhen the overhang is the same, select a holder with the largest
GROOVING
possible shank size to ensure sufficient clamping rigidity.
Modular blade (1)
GYM20R/LA-ooo
GYM25R/LA-ooo
GYM25R/LA-D12
GYM25R/LA-E12
GYM25R/LA-F12
GYM25R/LA-G14
GYM25R/LA-H14
GYM25R/LA-J14
aFor a 40 shank holder, if there is no restriction for use, select
a holder suitable for GYM25 blade.
GYM20R/LA-D10
GYM20R/LA-E10
GYM20R/LA-F10
GYM20R/LA-G12
GYM20R/LA-H12

Overhang
LDRED
F2
Tool chuck
aThe maximum groove depth is limited to the dimension
LDRED. When machining with longer overhangs, refer to the

dimension F2 of the tool used.
F118
Modular blade (2)
GYM25R/L-ooo
GYM20R/L-ooo
aFor an internal holder, select a modular blade listed above.
a Notes on multi-function machining (MF, MS, MM and BM breakers)

For internal grooving, the machining methods for external grooving (F107F108)
can be used, but please note the following precautions.
Coolant
Machining blind holes
0.5
during cutting. Maintain supply until the tool has been

retracted completely for improved ship disposal.
the above operation is recommended.

The recommended width of cut for x is 0.5mm.
GROOVING
aAs continuous chips tend to elongate at the back of the bore,
aSupply large amounts of coolant for effective chip disposal
Machining Wide Grooves

Grooving
aWhen the cutting edge width is x 2 groove width
aWhen the cutting edge width is x 2 < groove width

xcz
xcz
Chips
xcz
Coolant
aWhen the depth of cut is shallower than the cutting
edge width, continuous chips are usually produced.

When plunging in several passes, it is recommended
to carry out machining in the steps above. This ensures
that coolant reaches the cutting edge and chips are
easily discharged.
aWhen the groove depth is larger than the cutting edge width, carry
out plunging in the steps above to break up chips efficiently.
Machining instruction
Turning
0.5
aWhen chip breaking and
disposal are especially

important, cross-feed
machining is recommended.
0.5
aWide face grooving when the corner R of the work piece is
equal to the corner R of the insert, machine as shown above.

(When corner R of the work piece is larger than corner R of
the insert, refer to the description of external wide grooving.)
aIf the groove depth exceeds a given level, chips may elongate
aIt is recommended to carry
out grooving from the front

end of the workpiece.
This reduces workpiece
deflection.
at the wall. In such a case, increase the feed and carry out
machining as shown above.
F119
EXTERNAL GROOVING
UGHOLDER
UGHN
a Strengthened insert clamping force.

a Block and blade type and solid type series.
a Groove width 2.2 5.1mm
External cutting off, Grooving
HF
HTB
CW0.1
LB
150
Dimensions(mm)
Stock Insert Number
Order Number
GROOVING
CW
*
*
CUTDIA
CDX
Tool Block
B
HF
HTB
LB
Wrench
1.60
21.4
26
110
UGS1
UGHN262
2p
2.2
50
20
UGHN263
3p
3.1
75
32.5
2.35
21.4
26
110
UGS1
UGHN264
4p
4.1
80
35
3.20
21.4
26
110
UGS1
UGHN265
5p
5.1
80
35
4.00
21.4
26
110
UGS1
UGHN322
2p
2.2
50
20
1.60
25.0
32
150
UGS1
UGHN323
3p
3.1
100
45
2.35
25.0
32
150
UGS1
UGHN324
4p
4.1
100
45
3.20
25.0
32
150
UGS1
UGHN325
5p
5.1
120
55
4.00
25.0
32
150
UGS1
KGT
KGBN26-20
KGBN26-25
KGBN32-20
KGBN32-25
1 CUTDIA : Max. Cut off Diameter

2 CDX : Max. Groove Depth
TOOL BLOCK
100
Groove Depth:35 when

machining diameter is y
Groove Depth:32.5 when
Diameter of Workpiece (mm)
Clamp Screw
Set Bolt
HF
H
HBH
OAH
xShank
zBlock
OAW

Clamp Bridge
110

Order Number
Dimensions(mm)
Stock
H
HF
HBH OAH
OAW Clamp Bridge Clamp Screw
Wrench
Set Bolt
Wrench
KGBN26-20
20
20
11
45
20
43
KGC1
LS15T
TKY25R
HSC08016
HKY60R
KGBN26-25
25
25
45
25
48
KGC1
LS15T
TKY25R
HSC08016
HKY60R
KGBN32-20
20
20
15.6
52
20
43
KGC1
LS15T
TKY25R
HSC08016
HKY60R
KGBN32-25
25
25
10.6
52
25
48
KGC1
LS15T
TKY25R
HSC08016
HKY60R
(Note) zWhen ordering a block, the clamp bridge and clamp screw are included.
xWhen ordering a shank, the set bolts are included.
Clamp Torque (N m) : LS15T=8.5, HSC08016=24.0
F120

UGH
IA
WF
CU
LF
HF
LH

Stock
LH
UGHR/L1616
Dimensions(mm)
Insert Number
R L
LF
IA
CW
CUTDIA
CDX
HF
LF
LH
WF
H3
Wrench
UGHR/L1616H2
a a
2p
2.2
32
16
16
100
24
16
16.3
20
UGS1
UGHR/L1616H3
a a
3p
3.1
36
16
16
100
24
16
16.4
20
UGS1
UGHR/L2020K2A
a a
2p
2.2
32
20
20
125
24
20
20.3
UGS1
UGHR/L2020K2
a a
2p
2.2
42
20
20
125
25
20
20.3
UGS1
UGHR/L2020K3A
a a
3p
3.1
36
20
20
125
24
20
20.4
UGS1
UGHR/L2020K3
a a
3p
3.1
58
21
20
20
125
32
20
20.4
UGS1
UGHR/L2525M3
a a
3p
3.1
76
29
25
25
150
42
25
25.4
UGS1
UGHR/L2525M4
a a
4p
4.1
76
29
25
25
150
42
25
25.5
UGS1
CDX : Max. Groove Depth
Dimensions(mm)
Coated Cermet Carbide

UE6020
US735
NX2525
UTi20T
Order Number
CW RE
KGT2N
2.2 0.2
KGT3N
[ a a
3.1 0.2
KGT4N
[ a a
4.1 0.2
KGT5N
[ a a
5.1 0.2
KGT2R
2.2 0.2
KGT2L
2.2 0.2
KGT3R
3.1 0.2
KGT3L
3.1 0.2
KGT4R
4.1 0.2
KGT4L
4.1 0.2
KGT5R
5.1 0.2
KGT5L
5.1 0.2
Geometry
CW0.1
RE
CW0.1
RE
8
Groove Depth:0 when

Stock
INSERTS

Groove Depth:8 when
Groove Depth:0 when
Left hand tool holder shown.
(Note) The above insert is not compatible with other manufacturer's holders.
KGT
GROOVING
Order Number
TD
CW0.1
HF
TD
CW0.1
H3
CU
WF
External cutting off, Grooving


Work Material
Mild Steel
Hardness
Grade
< 180HB
UE6020 NX2525
UTi20T
UE6020 NX2525
UTi20T
Carbon Steel 180 280HB

Alloy Steel
280 350HB
M Stainless Steel
< 200HB
Feed (mm/rev)
Cutting Speed
(m/min)
Groove Width 2.2mm Groove Width 3.1mm Groove Width 4.1mm Groove Width 5.1mm
120 (100 140)
0.08 (0.06 0.1)
0.1 (0.08 0.12)
0.12 (0.1 0.14)
0.12 (0.1 0.14)
100 (80 120)
0.05 (0.04 0.06) 0.08 (0.06 0.1)
0.1 (0.08 0.12)
0.1 (0.08 0.12)
UTi20T
80 (60 100)
0.05 (0.04 0.06) 0.08 (0.06 0.1)
0.1 (0.08 0.12)
0.1 (0.08 0.12)
US735
80 (60 100)
0.05 (0.04 0.06) 0.08 (0.06 0.1)
0.1 (0.08 0.12)
0.1 (0.08 0.12)
(Note) Please set the cutting edge height 0.1 0.2mm higher than center.
SPARE PARTS
TECHNICAL DATA
P001
Q001
F121
EXTERNAL GROOVING
MGHOLDER
MGH
a Clamp-on type
a Positive insert suffers
from negligible chattering

and thus produces a good finished surface.
a Groove width 1.256.0mm
External grooving
CW
WF
CDX
LF
H
HF
Order Number
Stock
CW
a a
a a
MGHR/L2525M3323
MGHR/L2525M3333
MGHR/L2020K4315
LF
HF
WF
20
20
125
20
20.2
20
20
125
20
20.2
25
25
150
25
25.2
25
25
25
25
150
150
25
25
25.2
25.2
1.5
20
20
125
20
20.2
3.0 (3.5)
4.5 (4.0)
20
20
125
20
20.2
20
20
125
20
20.2
25
25
150
25
25.2
25
25
25
25
150
150
25
25
25.2
25.2
25
25
150
25
25.2
1.25
1.2
1.45
1.5
1.5 < CW < 2.3
3.0
33125
2.3 < CW < 3.3
3.0
1.25
1.2
MGTR/L
MGHR/L2525M3315
CDX
GROOVING
MGHR/L2020K3323
Dimensions(mm)
Insert Number
R L
MGHR/L2020K3315
33400
1.45
1.5
1.5 < CW < 2.3
3.0
a a
2.3 < CW < 3.3
a a
3.3 < CW < 4.7
3.0
3.0
a a
1.25
1.45
a a
1.2 (2.0)
*
2.3 < CW < 3.3
*
3.3 < CW < 4.7(4.0) * 4.5 (5.0)*
1.25
1.2 (2.0)*
1.5 < CW < 2.3
a a
MGHR/L2525M4315
a a
a a
43125
MGTR/L
MGHR/L2020K4323
MGHR/L2020K4333
43470
1.45
1.5
*
2.3 < CW < 3.3
*
3.3 < CW < 4.7(4.0) * 4.5 (5.0)*
3.0 (3.5)
4.5 (4.0)
1.5 < CW < 2.3
MGHR/L2525M4323
MGHR/L2525M4333
a a
MGHR/L2525M4447
a a
a a
44500
MGTR/L
44600
4.7 < CW < 6.3
4.5
* Dimensions when installing the CBN insert.

SPARE PARTS
*
Order Number
MGHR/L2020K3315
MGHR/L2525M4447
Clamp Bridge
Clamp Screw
Spring
Wrench
MTK1R/L
HBH06020
MES3
HKY40R
Grade
Feed (mm/rev)
VP20MF
120 (100 140)
0.14 (0.03 0.25)
NX2525
130 (100 160)
0.12 (0.03 0.2)
VP20MF
120 (100 140)
0.12 (0.03 0.18)
VP20MF
120 (100 140)
0.12 (0.03 0.18)
* Clamp Torque (N m) : HBH06020=7.0

Work Material
Carbon Steel
Alloy Steel
Stainless Steel
Gray Cast Iron
Hardness
180 280HB
< 200HB
Tensile Strength
< 350MPa
(Note) For machining a narrow groove, apply a lower feed within the recommended range.
F122

INSERTS
Dimensions(mm)
CW
PDPT
IC
4.76
0.2
1.45
1.5
9.525
4.76
0.2
MGTR/L33150
a a a a a a
1.5
9.525
4.76
0.2
MGTR/L33175
a a a a a a
1.75
9.525
4.76
0.2
MGTR/L33200
a a a a a a
9.525
4.76
0.2
MGTR/L33230
a a
a a
2.3
9.525
4.76
0.2
MGTR/L33250
a a a a a a
2.5
9.525
4.76
0.3
MGTR/L33270
a a
a a
2.7
9.525
4.76
0.3
MGTR/L33280
a a
a a
2.8
9.525
4.76
0.3
MGTR/L33300
a a a a a a
9.525
4.76
0.3
MGTR/L33320
a a
3.2
9.525
4.76
0.3
MGTR/L33330
a a
3.3
9.525
4.76
0.3
MGTR/L33350
a a a
a a
3.5
9.525
4.76
0.3
MGTR/L33400
a a a a a a
9.525
4.76
0.3
MGTR/L43125
a a a a a a
1.25
1.2
12.7
4.76
0.2
MGTR/L43145
a a
1.45
1.5
12.7
4.76
0.2
MGTR/L43150
a a a a a a
MGTR/L43175
a a a a a a
MGTR/L43200
a a a a a a
MGTR/L43230
a a a a
MGTR/L43250
a a a a a a
MGTR/L43260
a a a
a a
MGTR/L43270
a a
MGTR/L43280
a a
1.5
12.7
4.76
0.2
1.75
12.7
4.76
0.2
12.7
4.76
0.2
2.3
12.7
4.76
0.2
2.5
4.5
12.7
4.76
0.3
2.6
4.5
12.7
4.76
0.3
a a
2.7
4.5
12.7
4.76
0.3
a a
2.8
4.5
12.7
4.76
0.3
4.5
12.7
4.76
0.3
3.2
4.5
12.7
4.76
0.3
MGTR/L43300
a a a a a a
MGTR/L43320
MGTR/L43330
a a
3.3
4.5
12.7
4.76
0.3
MGTR/L43350
a a a a a a
3.5
4.5
12.7
4.76
0.3
MGTR/L43400
a a a
a a
4.5
12.7
4.76
0.3
MGTR/L43420
a a a
a a
4.2
4.5
12.7
4.76
0.4
MGTR/L43430
a a a
a a
4.3
4.5
12.7
4.76
0.4
MGTR/L43450
a a a a a a
4.5
4.5
12.7
4.76
0.4
MGTR/L43470
a a a a a a
4.7
4.5
12.7
4.76
0.4
MGTR/L44500
a a
a a
4.5
12.7
6.35
0.4
MGTR/L44550
5.5
4.5
12.7
6.35
0.4
MGTR/L44600
a a
4.5
12.7
6.35
0.4
a a
MGTR/L...
GROOVING
9.525
a a
PDPT
S
1.2
a a a
RE
IC
1.25
MGTR/L33145
CBN Insert
RE
PDPT
S
a a
IC
a a a
CW 0.025
MGTR/L33125
Geometry
RE
CW 0.03
R L R L R L
MB8025
UTi20T
NX2525
Order Number
VP20MF
Stock
SPARE PARTS
TECHNICAL DATA
P001
Q001
F123
EXTERNAL GROOVING
SMGHOLDER
SMGH
a Screw-on type
a Positive insert suffers from negligible chattering.
a Applicable to narrow grooving and threading.
2.5
LH
H
3.5
HF
HF
6
1.5 WF
2.5
LH
H3
1.5 WF
External grooving, Threading
LF
LF

Stock
Order Number
GROOVING
SMGHR1010E16
SMGHR1212F16
SMGHR1616H16
SMGHR2020K16
SMGHR2525M16
Insert Number
Grooving
Dimensions(mm)
Threading
SMGTR
SMTTR
162ppp
160360pp
162pppC
LF
LH
HF
WF
H3
Clamp Screw
10
10
70
16.5
10
12
14
FC400890T TKY10F
12
12
80
16.5
12
16
14
FC400890T TKY10F
16
16
100
20
16
20
FC400890T TKY10F
20
20
125
20
20
25
FC400890T TKY10F
25
25
150
20
25
32
FC400890T TKY10F
Wrench
* Clamp Torque (N m) : FC400890T=2.5

SMG INSERTS (GROOVING)
Stock
Dimensions(mm)
IC
BCH
0.5
1.5
9.525
SMGTR16X2060
a a
0.6
1.5
9.525
SMGTR16X2050C
a a
0.5
1.5
9.525
0.05
SMGTR16X2060C
a a
0.6
1.5
9.525
0.05
SMGTR16X2070C
a a
0.7
9.525
0.05
SMGTR16X2075C
a a
0.75
9.525
0.05
SMGTR16X2050
SMGTR16X2080C
a a
0.8
9.525
0.1
SMGTR16X2090C
a a
0.9
9.525
0.1
SMGTR16X2095C
a a
0.95
9.525
0.1
SMGTR16X2100C
a a
2.5
9.525
0.1
SMGTR16X2110C
a a
1.1
2.5
9.525
0.1
SMGTR16X2120C
a a
1.2
2.5
9.525
0.1
SMGTR16X2130C
a a
1.3
2.5
9.525
0.1
SMT INSERTS (THREADING)
SMTTR16036001
0.1
1.0 1.5
SMTTR16036002
0.2
1.75 2.0
Geometry
60
RE
(Note) Wet cutting is recommended.

a
F124
Hardness
PDPT
Grade
Cutting Speed
Feed
(m/min)
(mm/rev)
UTi20T
P Carbon Steel
180 280HB
NX2525
100
(80 120)
130
(100 160)
M Stainless Steel
UTi20T
130
0.1
(100 160) (0.05 0.15)
Alloy Steel
3.18
RE
Work
Material
Thread
Pitch
(mm)
9.525
UTi20T
Order Number
4.5
BCH
Stock Dimensions(mm)
Carbide
Geometry
PDPT
IC
CW
CW +0.05
0
NX2525
Order Number
UTi20T
HTi10
Cermet Carbide
K
N
< 200HB
Gray Cast Tensile Strength UTi20T

< 350MPa
Iron
HTi10
Aluminium
HTi10
Alloy
Brass
HTi10
Acrylic
HTi10
100
(80 120)
350
(300 400)
250
(200 300)
250
(200 300)
0.07
(0.03 0.1)
0.07
(0.03 0.1)
0.1
(0.05 0.15)
0.1
(0.05 0.15)
0.1
(0.03 0.15)
0.1
(0.03 0.15)
MICRO-MINI
a Solid carbide type with min. cutting diameter 3.2mm.

a Insert can be ground to suit the application.
a Suitable for a wide range of tooling including threading
and grooving.
MICRO-MINI STANDARD (SOLID CARBIDE BORING BAR)

Stock
Dimensions(mm)
Geometry
CW
DCON
LF
LDRED DMIN
F2
C03FR-BLS
2.0
80
15
3.2
1.0
C04FR-BLS
2.5
80
20
4.2
1.5
C05HR-BLS
3.0
100
25
5.2
2.0
DCON Shank Diameter

Flat Area
DCON
TF15
CW
LDRED
F2
Micro
Grain Carbide
Order Number
Flat Area
LF

Depth of Cut
(mm)
Cutting Speed (m/min) Feed (mm/rev)
Work Material
Alloy Steel
P Carbon Steel
180 280HB
Edge Condition
Excrescence Quantity
(l /d)
Corner Radius or BCH
Honing
40 (30 50)
0.05 ( 0.1)
0.2 (0.1 0.3)
0.1 0.5
0.01 0.05
Stainless Steel
40 (30 50)
0.05 ( 0.1)
0.2 (0.1 0.3)
< 0.4
0 0.03
Gray Cast Iron
40 (30 50)
0.05 ( 0.05)
0.2 (0.1 0.3)
0.1 0.5
0.01 0.05
Non-ferrous Metal
80 (60 100)
0.05 ( 0.1)
0.3 (0.1 0.5)
0.1 0.5
0 0.03
< 200HB
< 350MPa
GROOVING
*Cutting edge is not honed. Please hone according to the application before machining.
y GRINDING THE CUTTING EDGE OF MICRO-MINI
aMICRO-MINI can be applied to boring and grooving as supplied. But, it can also be reground as shown below.
aFor shaping and regrinding, use a diamond whetstone approximately #250 #400. Please grind according to the application using the figure below as a reference.
Grooving
12
12
(Grinding)
Grinding Examples
Application
Boring
25
Grinding
0.5 0.8
Thread Angle
Grinding
35
20
4 CW
Grinding
Grinding
60
(Grinding)
6
Groove Width
25
20
0. 5 0.8
R0.3 R0.5
Threading
6 Double Sided Relief
: Inventory maintained in Japan. (MICRO MINI is available in 1 piece in one pack.)
19
SPARE PARTS
TECHNICAL DATA
19
P001
Q001
F125
INTERNAL GROOVING
MICRO-MINI TWIN
DMIN
CW0.03 RE
RE
LU
F2
WF
y CG TYPE (Internal Grooving)
DCON
L19
GROOVING
Order Number
* CG03ppRS-ppB Only
Dimensions (mm)
Breaker
DMIN
CW
RE
DCON
LF
LU
L19
WF
Without
0.05
50
1.3
2.7
With
0.05
50
1.3
2.7
Without
0.1
50
1.3
2.7
With
0.1
50
1.3
2.7
Without
0.05
50
10
1.3
2.7
With
0.05
50
10
1.3
2.7
Without
0.1
50
11
1.3
2.7
With
0.1
50
11
1.3
2.7
Without
1.5
0.05
60
1.8
3.6
With
1.5
0.05
60
1.8
3.6
CG0408RS-20
Without
1.5
0.1
60
1.8
3.6
CG0408RS-20B
With
1.5
0.1
60
1.8
3.6
CG04RS-10
Without
1.5
0.05
60
15
1.8
3.6
CG04RS-10B
With
1.5
0.05
60
15
1.8
3.6
CG04RS-20
Without
1.5
0.1
60
16
1.8
3.6
CG04RS-20B
With
1.5
0.1
60
16
1.8
3.6
CG0510RS-10
Without
0.05
70
10
2.3
4.5
CG0510RS-10B
With
0.05
70
10
2.3
4.5
CG0511RS-20
Without
0.1
70
11
2.3
4.5
CG0511RS-20B
With
0.1
70
11
2.3
4.5
CG05RS-10
Without
0.05
70
20
2.3
4.5
CG05RS-10B
With
0.05
70
20
2.3
4.5
CG05RS-20
Without
0.1
70
21
2.3
4.5
CG05RS-20B
With
0.1
70
21
2.3
4.5
CG0610RS-10
Without
0.05
75
10
2.8
5.4
CG0610RS-10B
With
0.05
75
10
2.8
5.4
CG0611RS-20
Without
0.1
75
11
2.8
5.4
CG0611RS-20B
With
0.1
75
11
2.8
5.4
CG06RS-10
Without
0.05
75
20
2.8
5.4
CG06RS-10B
With
0.05
75
20
2.8
5.4
CG06RS-20
Without
0.1
75
21
2.8
5.4
CG06RS-20B
With
0.1
75
21
2.8
5.4
CG0712RS-10
Without
0.05
85
12
3.3
6.4
CG0712RS-10B
With
0.05
85
12
3.3
6.4
CG0713RS-20
Without
0.1
85
13
3.3
6.4
CG0713RS-20B
With
0.1
85
13
3.3
6.4
CG07RS-10
Without
0.05
85
25
3.3
6.4
CG07RS-10B
With
0.05
85
25
3.3
6.4
CG07RS-20
Without
0.1
85
26
3.3
6.4
CG07RS-20B
With
0.1
85
26
3.3
6.4
CG0305RS-10
CG0305RS-10B
CG0306RS-20
CG0306RS-20B
CG03RS-10
CG03RS-10B
CG03RS-20
CG03RS-20B
CG0407RS-10
CG0407RS-10B
F126
Stock
Micro Grain Carbide
Coated
TF15
VP15TF
H
LF
F2

Feed (mm/rev)
Work Material
Hardness
180 280HB
80 (40 120)
0.02 (0.01 0.03)
0.03 (0.01 0.05)
Stainless Steel
< 200HB
80 (40 120)
0.02 (0.01 0.03)
0.03 (0.01 0.05)
Gray Cast Iron
Tensile Strength
< 350MPa
80 (40 120)
0.03 (0.01 0.05)
0.03 (0.01 0.05)
Non-ferrous Metal
120 (80 160)
0.03 (0.01 0.05)
0.05 (0.01 0.08)
M
K
N
CG03RS/CG04RS CG05RS/CG06RS/CG07RS
Recommended Tool Overhang

(mm)
CG Type Micro-Mini Twin
LU + 2 (mm)
Holder
(Note) Wet cutting is recommended.

a When using a holder for general purpose / small automatic lathe:
may chip.
Fig.1
Internal Face of the Holder
Cutting Edge
Insert Direction
s When using this type of holder, there is a possibility that damage to the shank and the 2nd cutting
e When using Mitsubishi holders
screw is removed prior to machining. The set torque value for clamping screw is 2.0 Nm.
Fig.2
3rd Clamping Screw

1
Insert Point
GROOVING
a To avoid chipping of the 2nd cutting edge take care when inserting the boring bar into the holder.
2nd Cutting Edge
a When using a square type holder:

a When installing the boring bar into the holder, tighten the clamp screws after ensuring the flats on
s Make sure that the clamping screws are tightened to the recommended values.
d Do not tighten the clamp screw without a bar in place, otherwise the bridge will be deformed.
Fig.3
The Reference Plane
of Square Type Holder
Tighten the clamping screw ensuring making the micro-mini twin
boring bars in contact with the reference plane of square type holder.
Insert
F127
INTERNAL GROOVING
ROUND TYPE HOLDER
S2
S1
3-M4 x 0.7
S1
S2
3-M4 x 0.7
BD
BD
DCON
DCB
10
z
S3
20
LF

GROOVING
RBH15830N
RBH15840N
RBH15850N
RBH15860N
RBH15870N
RBH1630N
RBH1640N
RBH1650N
RBH1660N
RBH1670N
RBH19030N
RBH19040N
RBH19050N
RBH19060N
RBH19070N
RBH2030N
RBH2040N
RBH2050N
RBH2060N
RBH2070N
RBH2230N
RBH2240N
RBH2250N
RBH2260N
RBH2270N
RBH2530N
RBH2540N
RBH2550N
RBH2560N
RBH2570N
RBH25430N
RBH25440N
RBH25450N
RBH25460N
RBH25470N
*2
*2
*2
*2
*
2
Dimensions (mm)
BD
LF
S1
S2
S3
15.875
15
100
10
10
15.875
15
100
15
15
04FR-BLS
15.875
15
100
15
15
05HR-BLS
15.875
15.875
6
7
15
15
100
100
15
20
15
20
16
16
3
4
15
15
100
100
10
15
10
15
03FR-BLS
04FR-BLS
16
15
100
15
15
05HR-BLS
16
16
6
7
15
15
100
100
15
20
15
20
19.05
19.05
3
4
18
18
125
125
10
15
10
15
03FR-BLS
04FR-BLS
19.05
18
125
15
15
05HR-BLS
19.05
19.05
6
7
18
18
125
125
15
20
15
20
20
20
3
4
12
13
125
125
10
15
10
15
03FR-BLS
04FR-BLS
20
14
125
15
15
05HR-BLS
20
20
6
7
15
16
125
125
15
20
15
20
22
22
3
4
12
13
125
125
10
15
10
15
10
12.5
03FR-BLS
04FR-BLS
22
14
125
15
15
12.5
05HR-BLS
22
22
6
7
15
16
125
125
15
20
15
20
15
15
25
25
3
4
12
13
150
150
10
15
10
15
03FR-BLS
04FR-BLS
25
14
150
15
15
a
a
a
a
a
a
a
a
03FR-BLS
F128
03RS- pp(B)
04RS- pp(B)
A A A HKY20F
2.0
A A A HKY20F
2.0
2.0
A A A HKY20F
A A A HKY20F
2.0
2.0
03RS- pp(B)
04RS- pp(B)
05RS- pp(B)
A A A HKY20F
A A A HKY20F
2.0
2.0
A A A HKY20F
2.0
06RS- pp(B)
07RS- pp(B)
03RS- pp(B)
04RS- pp(B)
A A A HKY20F
A A A HKY20F
2.0
2.0
B B B HKY20F
B B B HKY20F
2.0
2.0
05RS- pp(B)
06RS- pp(B)
07RS- pp(B)
B B B HKY20F
2.0
B B B HKY20F
B B B HKY20F
2.0
2.0
03RS- pp(B)
04RS- pp(B)
05RS- pp(B)
A A B HKY20F
A B B HKY20F
2.0
2.0
A B B HKY20F
2.0
06RS- pp(B)
07RS- pp(B)
03RS- pp(B)
04RS- pp(B)
A B B HKY20F
A B B HKY20F
2.0
2.0
A B C A HKY20F
A B B A HKY20F
2.0
2.0
05RS- pp(B)
06RS- pp(B)
07RS- pp(B)
A B B A HKY20F
2.0
A B B A HKY20F
A B B A HKY20F
2.0
2.0
A B C HKY20F
A C C HKY20F
2.0
2.0
05HR-BLS
03RS- pp(B)
04RS- pp(B)
05RS- pp(B)
A C C HKY20F
2.0
A C C HKY20F
A C C HKY20F
2.0
2.0
05RS- pp(B)
06RS- pp(B)
07RS- pp(B)
25
25
6
7
15
16
150
150
15
20
15
20
06RS- pp(B)
07RS- pp(B)
25.4
25.4
3
4
12
13
150
150
10
15
10
15
03FR-BLS
04FR-BLS
A B C HKY20F
A C C HKY20F
2.0
2.0
25.4
14
150
15
15
05HR-BLS
03RS- pp(B)
04RS- pp(B)
05RS- pp(B)
A C C HKY20F
2.0
15
20
06RS- pp(B)
07RS- pp(B)
A C C HKY20F
A C C HKY20F
2.0
2.0
a
a
a
a
a
25.4
25.4
6
7
15
16
RBH190ppN
A A A HKY20F
150
150
15
20
number of clamp screw A=HSS04004, B=HSS04006, C=HSS04008

*12 Order
*
RBH1930N
RBH1940N
RBH1950N
RBH1960N
RBH1970N
DCON DCB
x
LF
1 Clamp Screw
MICRO-MINI MICRO-MINI TWIN
Torque
Wrench
(N m)
C
CG
z x c v
Stock
Order Number
10
RBH19030N
RBH19040N
RBH19050N
RBH19060N
RBH19070N
SQUARE TYPE HOLDER
20
10
100
10
L24
10 (Clamp)
WF
45
Dimensions (mm)
SBH1030R
SBH1040R
SBH1050R
SBH1060R
SBH1070R
Stock
B
WF
13.8
13.8
14.7
14.8
15.6
15.8
a
a
16.5
17.4
16.8
17.8
L24
Width of Cutting
Edge 1mm
Width of Cutting
Edge 2mm
13 17.5 (14)
18 22.5 (19)
14 16.5 (15)
19 21.5 (20)
23 27.5 (24)
23 32.5 (24)
28 38 (29)
24 26.5 (25)
24 31.5 (25)
29 37 (30)
MICRO-MINI TWIN
CG
Clamp Screw
Wrench
Torque
(N m)
03RS-10(B),03RS-20(B)
HSC05012 HKY40R
9.5
04RS-10(B),04RS-20(B)
05RS-10(B),05RS-20(B)
HSC05012 HKY40R
9.5
HSC05012 HKY40R
9.5
06RS-10(B),06RS-20(B)
07RS-10(B),07RS-20(B)
HSC05012 HKY40R
HSC05012 HKY40R
9.5
9.5
* L24 is the length of overhang for sufficient clamping, and ( ) is the recommended length for machining of carbon and alloy steel.
SPARE PARTS
P001
GROOVING
Order Number
MICRO-MINI TWIN CG
F129
INTERNAL GROOVING
FTYPE
a Min. cutting diameter 10mm

a Screw-on type
a Usable for various applications.
a Max. groove depth : 3mm
FSL51
Internal grooving, Threading
10
2
CW

WF
WF
2
LU
H
DCON
LF
2
CW
2
LU
H
DCON
LF
Order Number
Stock
Insert Number
GROOVING
Grooving
*2
Dimensions(mm)
Threading
DCON
LF
LU
WF
CW
1.2
1.5
2.0
1.5
2.0
3.0
2.0
3.0
4.0
FSL5108R
MLG10ppL
MLT1001L
125
30
4.8
FSL5110R
MLG10ppL
MLT1001L
10
150
40
5.8
FSL5112R
MLG14ppL
MLT1401L
12
180
50
6.8
10.8
FSL5114R
MLG14ppL
MLT1401L
14
180
60
7.8
12.4
FSL5116R
MLG20ppL
MLT2001L
16
200
70
9.7
14
Max.
Groove
Depth
1 (mm) Clamp
DMIN
Wrench
Screw
10
1.0
TS25 TKY08F
12
1.0
TS25 TKY08F
14
2.0
TS32 TKY08F
16
2.0
TS32 TKY08F
20
3.0
TS43 TKY15F

*12 DMIN
*
FSL52
(Carbide shank) Internal grooving, Threading

10
2
CW
WF
WF
2
LU
H
DCON
LF
2
CW
2
LU
LF
H
DCON
Order Number
Stock
R
Insert Number
Grooving
Threading
F130
DCON
LF
LU
WF
CW
1.2
1.5
2.0
1.5
2.0
3.0
2.0
3.0
4.0
FSL5208R
MLG10ppL
MLT1001L
125
60
4.8
FSL5210R
MLG10ppL
MLT1001L
10
150
70
5.8
FSL5212R
MLG14ppL
MLT1401L
12
180
80
6.8
10.8
FSL5214R
MLG14ppL
MLT1401L
14
180
85
7.8
12.4
FSL5216R
MLG20ppL
MLT2001L
16
200
115
9.7
14

*12 DMIN
*

*2
Dimensions(mm)
Max.
Groove
Depth
1 (mm) Clamp
DMIN
Wrench
Screw
10
1.0
TS25 TKY08F
12
1.0
TS25 TKY08F
14
2.0
TS32 TKY08F
16
2.0
TS32 TKY08F
20
3.0
TS43 TKY15F
1.2
MLG1012L
1.5
2
UTi20T
Order Number
Dimensions(mm)
L
W1 PDPT
MLG1015L
MLG1020L
RE
BCH
2.38
0.1
2.38
0.1
2.38
0.1
Geometry
MLG...L
PDPT
S
2
CW 0.025
Coated Carbide
CW
and pitch
(mm)
UP20M
Application
INSERTS
BCH
L
4.76
0.1
MLG1420L
11.8 6.5
4.76
0.1
MLG1430L
11.8 6.5
4.76
0.1
MLG2020L
16.8 9.03
6.35
0.1
MLG2030L
16.8 9.03
6.35
0.1
MLG2040L
16.8 9.03
6.35
0.1
MLG...L
PDPT
BCH
GROOVING
CW 0.025
11.8 6.5
MLG1415L
20
MLT1001L
2.38
0.1
MLT1401L
11.8 6.5
4.76
0.1
Pitch 1.5 3.5
MLT2001L
16.8 9.03
6.35
0.1
MLT
60
Pitch 1.5 2.0

Pitch 1.5 2.5
RE
L
15
W1
Threading
W1
1.5
Grooving
W1
15

Feed (mm/rev)
Grade
Cutting Speed
(m/min)
P Carbon Steel 180 280HB
UP20M UTi20T
90 (60 120)
0.05 (0.02 0.08) 0.05 (0.02 0.08) 0.05 (0.02 0.08) 0.05 (0.02 0.08)
280 350HB
UP20M UTi20T
80 (50 100)
0.03 (0.02 0.04) 0.03 (0.02 0.04) 0.03 (0.02 0.04) 0.03 (0.02 0.04)
Work Material
Alloy Steel
Hardness
1.2, 1.5mm
2.0mm
3.0mm
SPARE PARTS
TECHNICAL DATA
4.0mm
P001
Q001
F131
INTERNAL GROOVING
DPT4
a Min. cutting diameter : 40mm

a Pin lock type
a Exchangeable head type
Internal grooving
WF
BD
TYPE
BORING HEAD
(Max. Groove Width)
4.7
LF

Stock
Order Number
Insert Number
DPT4140R
*1
BD
LF
WF
DMIN
Lock Pin
Lock Screw
Stop Ring
Wrench
32
40
20
40
P21S
HSP08014
E01
HKY40R
40
50
25
50
P21S
HSP08014
E01
HKY40R
MGTL43ppp
(Note) Please use left hand insert.

2 Clamp Torque (N m) : HSP08014=7.0
*
*

z
zDesignation
32
xArbor Length (mm)

Symbol DCON
1
DCON
1.5
32
cArbor Diameter (mm)

Diameter(DCON)
Symbol
OAL
32
260
300
32
32
32
32
40
310
360
40
40
40
40
DCON
Order
Number
B13232
B14040
Dimensions (mm)
Set Bolt
Wrench
Head
Order Number
32 260 29 300
SD32
HKY60R
DPT4132R
40 310 37 360
SD40
HKY60R
DPT4140R
DCON LF
OAL
LF
OAL
D1
ap
y Relationship between prepared hole and groove depth for DPT4 type
5.0
CW
Groove Depth ap (mm)
4.0
Insert :
MGTR/L43250-43470 (CW=2.54.7) Range of grooving
3.0
Insert :
MGTR/L43150-43230 (CW=1.52.3) Range of grooving
2.0
Insert :MGTR/L43145 (CW=1.45) Range of grooving

1.0
Insert :MGTR/L43125 (CW=1.25) Range of grooving

40
60
80
100
120
140
160
180
Diameter of Prepared Hole D1 (mm)
F132
vHead Diameter (mm)

Diameter(BD)
Symbol
LF
Stock
GROOVING
DPT4132R
*2
Dimensions(mm)
200
INSERTS
Stock
Dimensions(mm)
MGTL43175
MGTL43200
RE
1.25
1.2
12.7
4.76
0.2
1.45
1.5
12.7
4.76
0.2
1.5
3.0
12.7
4.76
0.2
1.75
3.0
12.7
4.76
0.2
3.0
12.7
4.76
0.2
MGTL43230
2.3
3.0
12.7
4.76
0.2
MGTL43250
2.5
4.5
12.7
4.76
0.3
MGTL43260
2.6
4.5
12.7
4.76
0.3
MGTL43270
2.7
4.5
12.7
4.76
0.3
MGTL43280
2.8
4.5
12.7
4.76
0.3
MGTL43300
4.5
12.7
4.76
0.3
3.2
4.5
12.7
4.76
0.3
MGTL43330
3.3
4.5
12.7
4.76
0.3
MGTL43350
3.5
4.5
12.7
4.76
0.3
MGTL43400
4.5
12.7
4.76
0.3
MGTL43420
4.2
4.5
12.7
4.76
0.4
MGTL43430
4.3
4.5
12.7
4.76
0.4
MGTL43450
4.5
4.5
12.7
4.76
0.4
MGTL43470
4.7
4.5
12.7
4.76
0.4
MGTL43320
Geometry
MGTL...
PDPT
RE
GROOVING
MGTL43150
IC
CW 0.025
PDPT
IC
CW
MGTL43145
UTi20T
MGTL43125
NX2525
Order Number
VP20MF

Work Material
Hardness
Carbon Steel
Alloy Steel
180 280HB
Stainless Steel
< 200HB
Gray Cast Iron
Tensile Strength
< 350MPa
Grade
Feed (mm/rev)
VP20MF
120 (100 140)
0.14 (0.03 0.25)
NX2525
130 (100 160)
0.12 (0.03 0.2)
VP20MF
120 (100 140)
0.12 (0.03 0.18)
VP20MF
120 (100 140)
0.12 (0.03 0.18)
(Note) For machining a narrow groove, apply a lower feed within the recommended range.
SPARE PARTS
TECHNICAL DATA
P001
Q001
F133

OF THREADING
zClassified according to external or internal applications.
xSub-classified according to product series.
uses illustrations and arrows to depict the available machining
applications, such as external and internal threading.
TYPE OF TOOL HOLDER

indicates the initial letters for the order
number and cutting applications.
STANDARDS FOR APPLICABLE INSERTS

TITLE OF PRODUCT
INDICATION OF EXTERNAL
/INTERNAL APPLICATION
PRODUCT SECTION
indicates stock status, dimensions, etc.

for applicable inserts.
EXTERNAL THREADING
MMTE HOLDER
External threading
INTERNAL THREADING INSERTS
Stock
R
Clamp
Screw
Stop
Ring
Shim Screw
MMTER1212H16-C
12 12 100 25 12 16 SETK51 SETS51
CR4
HFC03008 CTE32TP15
MMTER1616H16-C
16 16 100 25 16 20 SETK51 SETS51
CR4
HFC03008 CTE32TP15
MMTER2020K16-C
20 20 125 26 20 25 SETK51 SETS51
CR4
HFC03008 CTE32TP15
MMTER2525M16-C
25 25 150 28 25 32 SETK51 SETS51
CR4
HFC03008 CTE32TP15
MMTER3232P16-C
32 32 170 32 32 40 SETK51 SETS51
CR4
HFC03008 CTE32TP15
MMTER2525M22-C
MMT22ER
25 25 150 32 25 32 SETK61 SETS61
CR5
HFC04010 CTE43TP15
MMTER3232P22-C
ppppp
32 32 170 32 32 40 SETK61 SETS61
CR5
HFC04010 CTE43TP15
Dimensions (mm)
Insert Number
MMT16ER
ppppp
LF
LH HF WF
Clamp
Bridge
Shim
Wrench
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY20F
xHKY25R
zTKY20F
xHKY25R
(Note) Select and use a shim as shown below (sold separately), dependant on the lead angle.
Clamp Torque (N m) : SETS51=3.5, SETS61=5.0, HFC03008=1.5, HFC04010=2.2
ISO Metric
SHIM
Inclination
Lead
Stock Angle Applicable
Angle Order Number
Holder
R
(')
(%)
Inclination
Lead
Stock Angle Applicable
Angle Order Number
Holder
R
(')
(%)
1.5
0.5
0.5
1.5
2.5
3.5
4.5
1.5
0.5
0.5
1.5
2.5
3.5
4.5
3
2
1
0
1
2
3
a
a
a
a
a
a
MMTER
ppppp
16-C
CTE43TN15
CTE43TN05
CTE43TP05
CTE43TP15
CTE43TP25
CTE43TP35
CTE43TP45
3
2
1
0
1
2
3
a
a
a
a
a
a
a
Insert
MMTER
Inclination
Angle
(')
ppppp
22-C
American UN
CTE32TN15
CTE32TN05
CTE32TP05
CTE32TP15
CTE32TP25
CTE32TP35
CTE32TP45
Shim
Standard shim delivered with the holder.
IDENTIFICATION
Designation
Application
E External
Hand of Tool
Right
R
12
12
Tool Size (mm)

(Height and Width)
12
12
16
16
20
20
25
25
32
32
40
40
16
Tool Length
(mm)
H
K
M
P
R
100
125
C
Insert Size
(mm)
16
22
9.525
Method of
Holding
C
Clamp-on
12.7
150
BSPT
MMT
Whitworth for BSW, BSP
THREADING
Order Number
Partial Profile 55
Details of position A
Refer to page G014, G016,
G018, G020 for size PDX, PDY.
Partial Profile 60
170
200
MMT11IRA60-S
MMT16IRA60-S
MMT16IRG60-S
MMT11IRA55-S
MMT16IRA55-S
MMT16IRG55-S
MMT11IR100ISO-S
MMT11IR125ISO-S
MMT11IR150ISO-S
MMT16IR100ISO-S
MMT16IR125ISO-S
MMT16IR150ISO-S
MMT16IR175ISO-S
MMT16IR200ISO-S
MMT16IR250ISO-S
MMT16IR300ISO-S
MMT16IR160UN-S
MMT16IR140UN-S
MMT16IR120UN-S
MMT16IR190W-S
MMT16IR140W-S
MMT16IR110W-S
MMT16IR190BSPT-S
MMT16IR140BSPT-S
MMT16IR110BSPT-S
VP20RT
VP15TF
Type
Coated
Order Number
a
a
Dimensions (mm)
Pitch
a
a
a
PDY
PDX
RE
48 16
48 16
14 8
6.35
9.525
9.525
3.04
3.44
3.44
0.8
0.8
1.2
0.9
0.9
1.7
0.03
0.03
0.11
Partial form
4816
4816
148
6.35
9.525
9.525
3.04
3.44
3.44
0.8
0.8
1.2
0.9
0.9
1.7
0.07
0.07
0.21
Partial form
3.04
3.04
3.04
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
0.6
0.8
0.8
0.6
0.8
0.8
0.9
1.0
1.1
1.1
0.9
0.9
1.1
0.7
0.9
1.0
0.7
0.9
1.0
1.2
1.3
1.5
1.5
1.1
1.2
1.4
0.06
0.08
0.10
0.06
0.08
0.10
0.11
0.13
0.17
0.20
0.11
0.12
0.14
0.58
0.72
0.87
0.58
0.72
0.87
1.01
1.15
1.44
1.73
0.92
1.05
1.22
Full form
16
14
12
6.35
6.35
6.35
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
19
14
11
9.525
9.525
9.525
3.44
3.44
3.44
0.8
1.0
1.1
1.0
1.2
1.5
0.18
0.25
0.32
0.86
1.16
1.48
Full form
19
14
11
9.525
9.525
9.525
3.44
3.44
3.44
0.8
1.0
1.1
0.9
1.2
1.5
0.18
0.25
0.32
0.86
1.16
1.48
Full form
0.51.5
0.51.5
1.753.0
1.0
1.25
1.5
1.0
1.25
1.5
1.75
2.0
2.5
3.0
a
a
a
a
a
a
a
Geometry
thread/inch
Total
Cutting
Depth
(mm)
IC
mm
THREADING
MMTE
Full form

Work Material
< 180HB
Carbon Steel
Alloy Steel
180 280HB
Stainless Steel
Gray Cast Iron

a
Hardness
Mild Steel
< 200HB
Tensile Strength
< 350MPa
Grade
VP10MF
VP15TF
VP20RT
VP10MF
VP15TF
VP20RT
VP15TF
VP20RT
VP10MF
VP15TF
150 (70 230)

100 (60 140)
80 (60 100)
140 (80 200)
100 (60 140)
80 (60 100)
80 (40 120)
Work Material
Hardness
Heat-Resistant Alloy
Titanium Alloy
H Heat-Treated Alloy
45 55HRC
Grade
VP10MF
VP15TF
VP20RT
VP10MF
VP15TF
VP20RT
VP10MF
VP15TF

45 (15 70)
30 (20 40)
60 (40 80)
45 (25 65)
50 (30 70)
40 (20 60)
140 (80 200)

90 (60 120)

CUTTING DEPTH GUIDE
LEGEND FOR STOCK

STATUS MARK
PAGE REFERENCE
is shown on the left hand page

SPARE PARTS
indicates reference pages, including the above,
on the right hand page of each double-page spread.
PRODUCT STANDARDS
indicates order numbers, stock status

(per right/left hand), applicable inserts,
holder dimensions, and spare parts.
a To Order :
G000
G041
for each work material classification, indicates recommended

cutting conditions according to the ISO categories for
cutting grades, P, M, K, S, and H.
For holder, please specify zorder number and hand of tool (right/left).
For insert, please specify zinsert number and xgrade.
TURNING TOOLS
THREADING
CLASSIFICATION (EXTERNAL THREADING) ................ G002
CLASSIFICATION (INTERNAL THREADING) ................. G003
CROSS REFERENCE OF THREAD PITCHES
EXTERNAL ............................................. G004
INTERNAL .............................................. G006
STANDARD THREAD AND CORRESPONDING INSERT HOLDER ... G008
STANDARD OF THREADING TOOLS
FEATURES OF MMT SERIES ............................... G010
EXTERNAL THREADING
MMTE HOLDER .......................................... G012
MT HOLDER ............................................... G022
SMG HOLDER ............................................ G024
INTERNAL THREADING
MMTI TYPE BORING BARS ............................. G013
MICRO-MINI TWIN BORING BARS .............. G026
F TYPE BORING BARS .................................... G030
D TYPE BORING HEAD ................................... G032
THREADING METHOD.......................................... G034
STANDARD OF DEPTH OF CUT .......................... G039
TROUBLE SHOOTING .......................................... G043

*G026
CT
G032
G030
G030
G031
G031
G014
G012
G013
G022
G022
G023
G033
G028
G029
G024
G025
G025
DPT2
FSL51
FSL52
MLG (INSERTS)
MLT (INSERTS)
MMT (INSERTS)
MMTE
MMTI
MT1
MTH
MTT (INSERTS)
MTT (INSERTS)
RBH
SBH
SMGH
SMGT (INSERTS)
SMTT (INSERTS)
G001
THREADING
CLASSIFICATION (EXTERNAL THREADING)

Name of Tool Holder
Insert Shape
MMTE Holder
Features
Shank Size
(H x W x L)
(mm)

a M-class 3-D breaker inserts and G-class
ground inserts available.
^ G012
MT Holder
12 x 12 x 100
16 x 16 x 100
a Available with a wiper cutting edge to
20 x 20 x 125
provide a precise thread geometry.

a Able to change lead angle by replacing
shim.
25 x 25 x 150
32 x 32 x 170
a Clamp-on type.
a Positive insert suffers from negligible
chattering and thus produces good

finished surface.
16 x 16 x 100
20 x 20 x 125
25 x 25 x 150
32 x 32 x 170
THREADING
^ G022
SMG Holder
a Screw-on type.
^ G024
SMALL TOOLS
TTAH
10 x 10 x
70
a Positive insert suffers from negligible
12 x 12 x
80
chattering and thus produces good

finished surface.
a Holder is capable of performing both
threading and grooving.
16 x 16 x 100
^ D024
CSVH
20 x 20 x 125
25 x 25 x 150
aTools to be equipped on Gang type tool posts.

a Small Shank: 8mm16mm
a High rigidity due to designing of vertical insert.
a The screw designed for common use on
10 x 10 x 120
front and back enables back clamping.
12 x 12 x 120
a Most suitable for threading diameters of
2 mm or smaller.
a Screw-on type.
a Tools to be equipped on Cam type tool posts.
a Small Shank: 7mm12mm
a Single holder for front turning,
^ D027
G002
back turning, grooving, threading and

cutting off operations.
a The most suitable for machining of small
parts with work diameter & 5mm or less.
a Screw-on type.
8 x 10 x 120
16 x 16 x 120
x 7
x 140
x 8
x 140
9.5 x 9.5 x 140

10
x 10
x 140
12
x 12
x 140
CLASSIFICATION (INTERNAL THREADING)

Shank Size
Name of Tool Holder
Insert Shape
MMTI
Features
a Minimum cutting diameter 13mm.
a M-class 3-D breaker inserts and G-class
(Dia. x L x Min.
Cutting Dia.)
(mm)
16 x 125 x 13
16 x 150 x 15
20 x 170 x 24
ground inserts available.

25 x 200 x 29
a Available with a wiper cutting edge to
32 x 250 x 37
provide a precise thread geometry.
a Able to change lead angle by replacing shim. 40 x 300 x 46
^ G013
FSL5

a Screw-on type.
a Applicable for threading, grooving and boring.
a Available with a carbide shank to prevent
vibration when machining deep holes.
^ G030
DPT2
8 x 125 x 10
10 x 150 x 12
12 x 180 x 14
14 x 180 x 16
16 x 200 x 20
a Pin lock type.

32 x 300 x 40
40 x 360 x 50
THREADING
^ G032
MICRO-MINI TWIN
Boring Bars

a Solid carbide type.
a Economical two cutting edge type.
3 x 50 x 3
4 x 60 x 4.5
5 x 70 x 6
6 x 75 x 7
^ G026
MICRO-MINI
Boring Bars
a Minimum cutting diameter 3.2mm.

a Solid carbide type.
a Insert can be ground to suit the
application.
3 x
80 x 3.2
4 x
80 x 4.2
5 x 100 x 5.2
^ E022
G003
THREADING
CROSS REFERENCE THREAD PITCH (EXTERNAL)

Application
Pipe fittings and couplings

for gas and water
General machining
Partial Profile Partial Profile ISO Metric
60
55
American
UN
1/4P
1/4P
RE=0.137P
30 30
UNC
UNF
G(PF)
Rp(PS)
W
NPT
thread/inch
mm
thread/inch
thread/inch
thread/inch
0.5 5.0
32 5
28 5
27, 18, 14
11.5, 8
0.5 5.0
(48 5)
48 5
0.5 5.0
48 5
Partial
form
0.25 4.5
(64 6)
20 9
0.25 4.5
64 6
Partial
form
0.25 2.0
(48 13)
0.25 2.0
48 13
M
UNC
UNF
Symbol
THREADING
55
Pitch
mm
(thread/inch)
Full
form
Partial
^ G012 form
MT Holder
^ G022
SMG Holder
^ G024
G004
147'
RE=0.137P
60
60
55
90
1/8P
1/8P
60
MMT Holder
American
NPT
Whitworth
for BSW, BSP
Type
Holder
Parallel
Pipe Thread
American
ACME
30
29
UNJ
API Buttress API Round

Casing
Casing&Tubing
1/8P
0.3707P
0.366P
RE=0.23851P
30 30
60
RE=0.18042P
10
90
R(PT)
Rc(PT)
Rp
NPTF
Rd
Tr
(TM)
ACME
(Tw)
UNJ
BCSG
CSG
LCSG
thread/inch
thread/inch
thread/inch
mm
thread/inch
thread/inch
thread/inch
thread/inch
28, 19
14, 11
27, 18, 14
11.5, 8
10, 8
6, 4
1.5, 2
3, 4, 5
12, 10
8, 6, 5
32 8
10, 8
THREADING
147'
90
RE=0.137P
147'
90
30 30
ISO
Trapezoidal
30
147'
RE=0.22105P
RE=0.25597P
30
RE=0.137P
27.527.5
Round
DIN 405
Oil and gas
American
NPTF
Aircraft and
aerospace
90
Taper Pipe
Thread
BSPT
Motion transmissions
147'
Pipe couplings
for food and fire
fighting industries
Steam, gas
and water line pipes
G005
THREADING
CROSS REFERENCE THREAD PITCH (INTERNAL)

Application
Pipe fittings and couplings

for gas and water
General machining
Partial Profile Partial Profile ISO Metric
60
55
American
UN
RE=0.137P
60
1/4P
THREADING
1/4P
RE=0.137P
30 30
UNC
UNF
G(PF)
Rp(PS)
W
NPT
thread/inch
mm
thread/inch
thread/inch
thread/inch
0.5 5.0
32 5
28 5
27, 18, 14
11.5, 8
0.5 5.0
(48 5)
48 5
0.5 5.0
48 5
Partial
form
1.5 3.5
(16 8)
1.5 3.5
16 8
Partial
form
0.25 4.5
(64 6)
0.25 4.5
64 6
Partial
form
0.5 1.75
(36 16)
0.5 1.75
36 16
M
UNC
UNF
Symbol
Pitch
mm
(thread/inch)
Boring Bars
55
Full
form
Partial
^ G013 form
FSL5
Boring Bars
^ G030
DPT2
Boring
Head
^ G032
MICRO-MINI
TWIN
^ G026
G006
147'
60
55
90
1/8P
1/8P
60
MMT
American
NPT
Whitworth
for BSW, BSP
Type
Holder
Parallel
Pipe Thread
American
ACME
30
29
UNJ
API Buttress API Round

Casing
Casing&Tubing
1/8P
0.3707P
0.366P
RE=0.23851P
30 30
60
RE=0.18042P
10
90
R(PT)
Rc(PT)
Rp
NPTF
Rd
Tr
(TM)
ACME
(Tw)
UNJ
BCSG
CSG
LCSG
thread/inch
thread/inch
thread/inch
mm
thread/inch
thread/inch
thread/inch
thread/inch
19, 14, 11
14, 11.5, 8
10, 8
6, 4
1.5, 2
3, 4, 5
12, 10
8, 6, 5
10, 8
THREADING
147'
90
RE=0.137P
147'
90
30 30
ISO
Trapezoidal
30
147'
RE=0.22105P
RE=0.25597P
30
RE=0.137P
27.527.5
Round
DIN 405
Oil and gas
American
NPTF
Aircraft and
aerospace
90
Taper Pipe
Thread
BSPT
Motion transmissions
147'
Pipe couplings
for food and fire
fighting industries
Steam, gas
and water line pipes
machining an internal UNJ thread, cut an internal hole with the appropriate diameter. Then machine with 60 American UN.
* InWhen
this case, a full form type insert cannot be used.
G007
THREADING
STANDARD THREAD AND CORRESPONDING INSERT HOLDER

Thread
Name
Type Ext./Int.
H/8
Standard Thread Type
H/2
H1
H
30
30
d or D
60
External thread
P
H/8
H=0.866025P d2=d-0.649519P
H1=0.541266P d1=d-1.082532P
D=d D2=d2 D1=d1
H/2
H1
H
Ext.
30
d or D
60
d2 or D2
External thread
d1 or D1
H/4
H/2
American UN
THREADING
Int.
Internal
thread
30
UNC
UNF
H=0.86602525.4/n d2=(d-0.649519/n)25.4
H1=0.54126625.4/n d1=(d-1.082532/n)25.4
d=(d)25.4 D=d D2=d2 D1=d1 P=25.4/ thread
Int.
Internal
thread
Ext.
External thread
P
H=0.9605P d2=d-H1 d1=d-2H1 r=0.1373P

H1=0.6403P D1'=d1+20.0769H
D=d D2=d2 D1=d1 P=25.4/ thread
d1 or D1
D 1'
d2 or D2
d or D
27.5 27.5
55
Int.
Wiper : Insert order number is determined by selected pitch.

General : An insert is applicable to several pitch types.
G008
MMTooIRoooISO
MMTooIRoooISO-S
MMTooIRooo60
MMTooIRooo60-S
MTTR/L4360oo
MMTooERoooUN
MMTooERoooUN-S
MMTooERooo60
MMTooERooo60-S
SMTTR/L160360oo
MTTR/L4360oo
H/6
H/2
H1
0.0769H
H
H/2
H/6
MTTR/L4360oo
d1 or D1
d2 or D2
H/4
H/2
ISO Metric
Ext.
Internal
thread
Wiper/
General
Wiper
MMTooERoooISO
MMTooERoooISO-S Wiper
General
MMTooERooo60
MMTooERooo60-S General
General
SMTTR/L160360oo
Insert Number
Tool Holder
Page
MMTERooooo-C
G012
SMGHR/Loooo16
MTHR/Looooo4
General
MT1R/Looooo4
G024
Wiper
Wiper
General
General
General
Wiper
Wiper
General
General
General
G022
MMTIRooAooo-SPo
MMTIRooAo16-C
G013
DPT2oooR
G032
MMTERooooo-C
G012
SMGHR/Loooo16
MTHR/Looooo4
General
MT1R/Looooo4
G024
MMTooIRoooUN
MMTooIRoooUN-S
MMTooIRooo60
MMTooIRooo60-S
MTTR/L4360oo
MMTooERoooW
MMTooERoooW-S
MMTooERooo55
MMTooERooo55-S
Wiper
Wiper
General
General
General
Wiper
Wiper
General
General
MTTR/L4355oo
General
MMTooIRoooW
MMTooIRoooW-S
MMTooIRooo55
MMTooIRooo55-S
MTTR/L4355oo
Wiper
Wiper
General
General
General
G022
MMTIRooAooo-SPo
MMTIRooAo16-C
G013
DPT2oooR
G032
MMTERooooo-C
G012
MTHR/Looooo4
MT1R/Looooo4
G022
MMTIRooAooo-SPo
MMTIRooAo16-C
G013
DPT2oooR
G032
Type Ext./Int.
Internal
thread
27.5 27.5
d or D
55
PF
G
Rp
d1 or D1
d2 or D2
H/6
External thread
P
h/2
H/2
MMTooERoooW-S
Wiper
MMTooIRoooW
Wiper
Tool Holder
MMTERooooo-C
MMTooIRoooW-S
Wiper
MMTooERoooBSPT
Wiper
MMTIRooAooo-SPo
MMTIRooAo16-C
MMTERooooo-C
MMTooERoooBSPT-S
Wiper
MMTooIRoooBSPT
Wiper
MMTooIRoooBSPT-S
Wiper
Ext.
MMTooERoooRD
Wiper
Int.
MMTooIRoooRD
Wiper
Ext.
MMTooERoooTR
Wiper
Int.
MMTooIRoooTR
Wiper
Ext.
MMTooERoooACME
Wiper
Int.
MMTooIRoooTACME
Wiper
Ext.
MMTooERoooNPT
Wiper
Int.
MMTooIRoooNPT
Wiper
Page
G012
G013
G012
BSPT
16
Int.
BSPT
90
Thread center axis
Wiper
Ext.
h/2
H/2
Internal
thread
27.5 27.5
55
MMTooERoooW
Int.
H=0.960491P d2=d-h d1=d-2h r=0.137329P

h=0.640327 D=d D2=d2 D1=d1 25.4/ thread
Wiper/
General
Ext.
Insert Number
MMTIRooAooo-SPo
MMTIRooAo16-C
G013
H=0.960237P h=0.640327 r=0.137278P P=25.4/ thread
Internal
thread
h3
D1
D2
D4
ac
d3
External
thread
MMTERooooo-C
G012
H4
ac
h3/2
R1
d
d2
R2
R3
Round DIN 405
30
THREADING
H/2
H/6
Standard Thread Type
H/2
Parallel Pipe Thread
Thread
Name
Rd
MMTIRooAooo-SPo
MMTIRooAo16-C
G013
H/2
0.366P
H1/2 H1/2
15 15
30
External
thread
0.366P
MMTIRooAooo-SPo
MMTIRooAo16-C
G013
Frm
MMTERooooo-C
G012
Fcs
h
P/4 P/4
American ACME
G012
Internal
thread
29
1430' 1430'
MMTERooooo-C
Tr
d1 or D1
d2 or D2
d or D
H1
Internal
thread
H/2
ISO Trapezoidal 30
ac=0.05P h3=H4=0.5P
R1=0.238507P R2=0.255967P R3=0.221047P
ACME
Fcn
Frs
P
External
thread
MMTIRooAooo-SPo
MMTIRooAo16-C
G013
Fc
fc
Fr
MMTERooooo-C
G012
NPT
fc
Fr 3
0 30
60
147'
fc
Fc
American NPT
fr
Internal thread
MMTIRooAooo-SPo
MMTIRooAo16-C
G013
External thread
H=0.866025P h=0.800000p
Wiper : Insert order number is determined by selected pitch.

General : An insert is applicable to several pitch types.
G009
THREADING
FEATURES OF MMT SERIES

y A WIDE VARIETY OF PRODUCTS
Mitsubishi Miracle Threading (MMT) series. 283 inserts and 26 holders.
M-CLASS INSERTS WITH 3-D CHIP BREAKERS
G-CLASS GROUND INSERTS
UNC
Rp
THREADING
Rc
UNC
UNF
Rp
Rc
UNF
F
NPT
NPT
W
Rd
Tr
ACM
CSG
LCS
BCS
y IDEAL CHIP CONTROL EVEN IN THE LATTER HALF OF PASSES WHEN CONTINUOUS CHIPS
ARE USUALLY PRODUCED. (M-CLASS INSERTS WITH 3-D CHIP BREAKERS)

ISO metric external thread pitch 1.5mm Final pass (6th pass)
MMT
Competitor
Workpiece : JIS SCM440
Insert : MMT16ER150ISO-S
Grade : VP15TF
Cutting method : Radial Infeed
Depth of cut : Fixed cut area
Pass : 6 times
Coolant : Wet
y A HIGHER LEVEL OF PRECISION THAN
CONVENTIONAL INSERTS (G-CLASS GROUND INSERTS)

Theoretical
thread profile
MMT series
Conventional insert
High precision threading can be achieved by using MMT

inserts that feature a ground rake face and peripheral cutting
edge.
G010
Thread Type
Threading Tolerance
ISO Metric
6g / 6H
American UN
2A / 2B
Medium Class A
BSPT
Standard BSPT
Round DIN 405
7h / 7H
ISO Trapezoidal 30
7e / 7H
American ACME
3G
UNJ
3A
API Buttress Casing
Standard API
API Rounded Casing & Tubing
Standard API RD
American NPT
Standard NPT
American NPTF
Class2
y HOLDER (Use of special surface treatment)

External
Internal
Clamp-on type allows

easy indexing.
Coolant flows directly to

the cutting edge through
a coolant nozzle in the
center of the shank.
Reduced neck MMT holders

prevents chips from jamming.
By changing the shim, MMT holders

can be used for cutting threads with
various lead angles.
y SUITABLE FOR THREADING WITH A LARGE LEAD ANGLE

Lead Angle (%)
Insert
Inclination
Angle
(')
Lead Angle
(%)
Inclination Angle
(')
1.5
0.5
0.5
1.5
2.5
3.5
4.5
Shim
By changing only the shim, MMT holders can be used for turning of threads
with various lead angles as well as the turning of left hand threads.
THREADING
Order number of coolant guide screw: TFS03006

* (Except
MMTIR1316/MMTIR1516)
Standard shim delivered with the

holder.
y GRADE
VP10MF (G-class ground insert only)

a Superior wear and plastic deformation resistance
High wear and plastic deformation resistance for threading when maintaining the thread form is important. Suitable for continuous
high precision machining with extensive tool life.
Effective in combination with G-class inserts for high precision threading.
VP15TF (G-class ground insert, M-class insert with 3-D chip breakers)
a Wide versatility
High fracture resistance during low rigidity applications such as bar feed machining. Able to withstand harsh conditions for long
periods where conventional inserts would be liable to breakage.
Effective combination of high cost performance M-class inserts with 3-D chip breakers.
VP20RT (M-class insert with 3-D chip breakers)

a Excellent fracture resistance
Suitable for stainless steel boring and unstable machining where inserts are vulnerable to fracturing.
Effective combination of high cost performance M-class inserts with 3-D chip breakers.
y CHOOSING M-CLASS INSERTS WITH 3-D CHIP BREAKERS OR G-CLASS INSERTS

Insert
Chip control
Precision of
thread
Insert
Chip control
Precision of
thread
G-class inserts
M-class inserts with 3-D chip

breakers
For ideal chip control and a high

cost performance ratio, M-class
inserts with 3-D chip breakers are
recommended.
G-class inserts are recommended
where higher precision is required.
G011
EXTERNAL THREADING
MMTE HOLDER
MMTE
1.5
PDX
WF
WF
External threading
PDY
LH
A
LF
LF
G018, G020 for size PDX, PDY.
HF
10
Stock
THREADING
Order Number
Dimensions (mm)
Insert Number
z
x
Clamp
Screw
Stop
Ring
Shim Screw
MMTER1212H16-C
12 12 100 25 12 16 SETK51 SETS51
CR4
HFC03008 CTE32TP15
MMTER1616H16-C
16 16 100 25 16 20 SETK51 SETS51
CR4
HFC03008 CTE32TP15
20 20 125 26 20 25 SETK51 SETS51
CR4
HFC03008 CTE32TP15
25 25 150 28 25 32
SETK51 SETS51
CR4
HFC03008 CTE32TP15
32 32 170 32 32 40 SETK51 SETS51
CR4
HFC03008 CTE32TP15
MMT16ER
LF
LH HF WF
Clamp
Bridge
Shim
Wrench
MMTER2020K16-C
MMTER2525M16-C
MMTER3232P16-C
MMTER2525M22-C
MMT22ER
25 25 150 32 25 32 SETK61 SETS61
CR5
HFC04010 CTE43TP15
MMTER3232P22-C
ppppp
32 32 170 32 32 40 SETK61 SETS61
CR5
HFC04010 CTE43TP15
ppppp
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY20F
xHKY25R
zTKY20F
xHKY25R
Clamp Torque (N m) : SETS51=3.5, SETS61=5.0, HFC03008=1.5, HFC04010=2.2
SHIM
Lead
Stock Inclination Applicable
Angle
Angle Order Number
Holder
R
(')
(%)
Lead
Angle
Angle Order Number
Holder
R
(')
(%)
1.5
0.5
0.5
1.5
2.5
3.5
4.5
1.5
0.5
0.5
1.5
2.5
3.5
4.5
CTE32TN15
CTE32TN05
CTE32TP05
CTE32TP15
CTE32TP25
CTE32TP35
CTE32TP45
3
2
1
0
1
2
3
a
a
a
a
a
a
a
MMTER
ppppp
16-C
CTE43TN15
CTE43TN05
CTE43TP05
CTE43TP15
CTE43TP25
CTE43TP35
CTE43TP45
a
a
a
a
a
a
a
3
2
1
0
1
2
3
Insert
MMTER
22-C
Inclination
Angle
(')
16
ppppp
Shim
IDENTIFICATION
MMT
Designation
Application
E External
Hand of Tool
Right
R
12
12
Tool Size (mm)

(Height and Width)
12
12
16
16
20
20
25
25
32
32
Tool Length
(mm)
H
K
M
P
100
125
Insert Size
(mm)
16
22
9.525
Method of
Holding
C
Clamp-on
12.7
150
170

Work Material
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180 280HB
Stainless Steel
< 200HB
Gray Cast Iron

a
G012
Hardness
Tensile Strength
< 350MPa
Grade
VP10MF
VP15TF
VP20RT
VP10MF
VP15TF
VP20RT
VP15TF
VP20RT
VP10MF
VP15TF
150 (70230)
100 (60140)
80 (60100)
140 (80200)
100 (60140)
80 (60 100)
80 (40120)
140 (80200)
90 (60120)
Work Material
Hardness
Heat-Resistant Alloy
Titanium Alloy
H Heat-Treated Alloy
4555HRC
Grade
VP10MF
VP15TF
VP20RT
VP10MF
VP15TF
VP20RT
VP10MF
VP15TF
45 (15 70)
30 (20 40)
60 (40 80)
45 (2565)
50 (30 70)
40 (2060)
INTERNAL THREADING
MMTI
MMTI
TYPE
BORING BARS
Internal threading
MMTIR1316AK11-SP15
MMTIR1316AK11-SP25
MMTIR1316AK11-SP35
MMTIR1516AM11-SP15
MMTIR1516AM11-SP25
MMTIR1516AM11-SP35
MMTIR1916AM16-SP15
MMTIR1916AM16-SP25
MMTIR1916AM16-SP35
MMTIR2420AQ16-C
MMTIR2925AS16-C
MMTIR3732AS16-C
MMTIR2420AQ22-SP15
MMTIR2420AQ22-SP25
MMTIR2420AQ22-SP35
MMTIR3025AR22-C
MMTIR3832AS22-C
MMTIR4640AT22-C
WF
x Fig
Clamp
DMIN Bridge
Clamp
Screw
Stop Shim Screw

Ring
Shim
Wrench
TS25
zTKY08F 1
TS25
zTKY08F 1
MMT11IR 3.5 16 125 25

ppppp 1.5 16 150 32
8.7 15
13
TS25
zTKY08F 1
9.7 15
15
TS25
zTKY08F 1
2.5 16 150 32
3.5 16 150 32
9.7 15
9.7 15
15
15
TS25
zTKY08F 1
TS25
zTKY08F 1
1.5 16 150 40 12.2 15

2.5 16 150 40 12.2 15
19
19
CS350860T
zTKY15F 2
CS350860T
zTKY15F 2
MMT16IR 3.5 16 150 40 12.2 15

ppppp 1.5 20 180 40 14.2 19
19
CS350860T
24
SETK51
SETS51
CR4
HFC03006 CTI32TP15
1.5 25 250 60 16.7 23.4 29

1.5 32 250 48 20.5 30.4 37
SETK51
SETS51
CR4
HFC03006 CTI32TP15
SETK51
SETS51
CR4
HFC03006 CTI32TP15
24
24
TS43
zTKY15F 2
TS43
zTKY15F 2
24
MMT22IR 3.5 20 180 50 15.5 19
ppppp 1.5 25 200 38 17.8 23.4 30
TS43
SETK61
SETS61
CR5
HFC04008 CTI43TP15
SETK61
SETS61
CR5
HFC04008 CTI43TP15
SETK61
SETS61
CR5
HFC04008 CTI43TP15
a
a
1.5 20 180 50 15.5 19

2.5 20 180 50 15.5 19
a
a
*
13
13
8.7 15
8.7 15
PDX G019, G021 for size PDX,
LF PDY.
LF
Dimensions (mm)
H
LF
1.5 16 125 25
2.5 16 125 25
LDRED
LF
DCON LF LDRED WF
LDRED
Insert
Lead
Number Angle
Fig.4 (Clamp-on type)
LDRED
1.5 32 250 48 21.8 30.4 38

1.5 40 300 60 26.2 38
46
a
a
zTKY15F 2
zTKY15F
xHKY20R
zTKY15F
xHKY20R
zTKY15F
xHKY20R
3
3
4
THREADING
Stock
DMIN
H
DCON
LF
Fig.3 (Clamp-on type)
WF
15
Order Number
LDRED
WF
PDY
WF
DMIN
Fig.2 (Screw-on type)

WF
Fig.1 (Screw-on type)
15
zTKY15F 2
zTKY20F
xHKY25R
zTKY20F
xHKY25R
zTKY20F
xHKY25R
4
4
4
A screw-on tool holder uses no shim. (The holder body has a lead angle.) Use a tool holder with the appropriate lead angle.
Min. cutting diameter (DMIN) shows the internal hole diameter, not the thread diameter.
Clamp Torque (N m) : TS25=1.0, CS350860T=3.5, SETS51=3.5, TS43=3.5, SETS61=5.0, HFC03006=1.5, HFC04008=2.2
SHIM
Lead
Angle
Angle Order Number
Holder
R
(')
(%)
1.5
0.5
0.5
1.5
2.5
3.5
4.5
CTI32TN15
CTI32TN05
CTI32TP05
CTI32TP15
CTI32TP25
CTI32TP35
CTI32TP45
a
a
a
a
a
a
a
3
2
1
0
1
2
3
MMTIR
pppp
pp16-C
Lead
Angle
Angle Order Number
Holder
R
(')
(%)
1.5
0.5
0.5
1.5
2.5
3.5
4.5
CTI43TN15
CTI43TN05
CTI43TP05
CTI43TP15
CTI43TP25
CTI43TP35
CTI43TP45
a
a
a
a
a
a
a
3
2
1
0
1
2
3
Insert
MMTIR
pppp
pp22-C
Inclination
Angle
(')
Shim
IDENTIFICATION
MMT I
Designation
R 13 16 A K 11
Application
I Internal
Min.Cutting Diameter (mm)
Hand of Tool
Right
R
Shank Material
Shank Diameter (mm)
Steel Shank with

Coolant Hole
Tool Length (mm)

125
200
K
R
150
250
M
S
180
300
Q
T
S P15
Insert Size
(mm)
11
16
22
6.35
9.525
12.7
Method of
Holding
S Screw-on
C Clamp-on
HOW TO SELECT A SHIM
Lead Angle
1.5
P15
2.5
P25
3.5
P35
G037, G038
G013
THREADING
MMT
M-CLASS INSERTS
WITH 3-D CHIP BREAKERS
EXTERNAL THREADING INSERTS
Partial Profile 60
MMT16ERA60-S
MMT16ERG60-S
VP20RT
Order Number
a
a
Dimensions (mm)
Pitch
mm
thread/inch
0.51.5
1.753.0
48 16
14 8
IC
PDY
PDX
RE
9.525
9.525
3.44
3.44
0.8
1.2
0.9
1.7
0.06
0.23
Total
Cutting
Depth
(mm)
Geometry
Partial form
60
PDX
RE
PDY
IC
Partial Profile 55
MMT16ERA55-S
MMT16ERG55-S
48 16
14 8
a
a
9.525
9.525
3.44
3.44
0.8
1.2
0.9
1.7
0.07
0.23
Partial form
55
PDX
RE
PDY
IC
ISO Metric
MMT16ER100ISO-S
MMT16ER125ISO-S
MMT16ER150ISO-S
MMT16ER175ISO-S
MMT16ER200ISO-S
MMT16ER250ISO-S
MMT16ER300ISO-S
MMT16ER160UN-S
MMT16ER140UN-S
MMT16ER120UN-S
American UN
THREADING
VP15TF
Type
Coated
1.0
1.25
1.5
1.75
2.0
2.5
3.0
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
16
14
12
a
a
a
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
0.7
0.8
0.8
0.9
1.0
1.1
1.2
0.9
1.0
1.1
0.7
0.9
1.0
1.2
1.3
1.5
1.6
1.1
1.2
1.4
0.13
0.16
0.20
0.22
0.26
0.33
0.40
0.23
0.26
0.30
0.61
0.77
0.92
1.07
1.23
1.53
1.84
0.97
1.11
1.30
Full form
60
PDX
IC
Full form
60
PDX
19
14
11
a
a
a
9.525
9.525
9.525
3.44
3.44
3.44
0.8
1.0
1.1
1.0
1.2
1.5
0.18
0.25
0.32
0.86
1.16
1.48
IC
Full form
55
PDX
BSPT
19
14
11
a
a
a
9.525
9.525
9.525
3.44
3.44
3.44
0.8
1.0
1.1
0.9
1.2
1.5
0.18
0.25
0.32
0.86
1.16
1.48
RE
PDY
IC
MMT16ER190BSPT-S
MMT16ER140BSPT-S
MMT16ER110BSPT-S
RE
PDY
MMT16ER190W-S
MMT16ER140W-S
MMT16ER110W-S
RE
PDY
Full form
55
PDX
RE
PDY
IC
IDENTIFICATION
MMT
16
Designation
G014
100
Hand of Tool
Right
R
Diameter of
Inscribed Circle
(mm)
6.35
11
16
9.525
Application
E External
Internal
I
ISO
Pitch
100
1.0mm
125
1.25mm
150
1.5mm
175
1.75mm
200
2.0mm
250
2.5mm
300
3.0mm
0.51.5mm
or
4816 thread/inch
1.75 3.0mm
or
14 8 thread/inch
M-class inserts with

3-D chip breakers
Threading Type
60 Partial Profile 60
ISO ISO Metric
W Whitworth for BSW, BSP
BSPT BSPT
UN American UN

CUTTING DEPTH GUIDE
G039
BSPT
American UN
MMT11IRA60-S
MMT16IRA60-S
MMT16IRG60-S
VP20RT
VP15TF
Order Number
a
a
a
Dimensions (mm)
Pitch
mm
thread/inch
0.51.5
0.51.5
1.753.0
48 16
48 16
14 8
IC
PDY
PDX
RE
6.35
9.525
9.525
3.04
3.44
3.44
0.8
0.8
1.2
0.9
0.9
1.7
0.03
0.03
0.11
Total
Cutting
Depth
(mm)
Geometry
Partial form
RE
PDY
MMT11IRA55-S
MMT16IRA55-S
MMT16IRG55-S
48 16
48 16
14 8
a
a
a
6.35
9.525
9.525
3.04
3.44
3.44
0.8
0.8
1.2
0.9
0.9
1.7
0.07
0.07
0.21
a
a
a
a
a
a
a
1.0
1.25
1.5
1.0
1.25
1.5
1.75
2.0
2.5
3.0
16
14
12
6.35
6.35
6.35
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
3.04
3.04
3.04
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
0.6
0.8
0.8
0.6
0.8
0.8
0.9
1.0
1.1
1.1
0.9
0.9
1.1
0.7
0.9
1.0
0.7
0.9
1.0
1.2
1.3
1.5
1.5
1.1
1.2
1.4
0.06
0.08
0.10
0.06
0.08
0.10
0.11
0.13
0.17
0.20
0.11
0.12
0.14
0.58
0.72
0.87
0.58
0.72
0.87
1.01
1.15
1.44
1.73
0.92
1.05
1.22
RE
a
a
a
19
14
11
9.525
9.525
9.525
3.44
3.44
3.44
0.8
1.0
1.1
1.0
1.2
1.5
0.18
0.25
0.32
0.86
1.16
1.48
a
a
a
19
14
11
9.525
9.525
9.525
3.44
3.44
3.44
0.8
1.0
1.1
0.9
1.2
1.5
0.18
0.25
0.32
0.86
1.16
1.48
IC
Full form
RE
60
PDX
PDY
IC
Full form
RE
60
PDX
PDY
IC
Full form
RE
55
PDX
PDY
MMT16IR190BSPT-S
MMT16IR140BSPT-S
MMT16IR110BSPT-S
55
PDX
PDY
MMT16IR190W-S
MMT16IR140W-S
MMT16IR110W-S
IC
Partial form
MMT11IR100ISO-S
MMT11IR125ISO-S
MMT11IR150ISO-S
MMT16IR100ISO-S
MMT16IR125ISO-S
MMT16IR150ISO-S
MMT16IR175ISO-S
MMT16IR200ISO-S
MMT16IR250ISO-S
MMT16IR300ISO-S
MMT16IR160UN-S
MMT16IR140UN-S
MMT16IR120UN-S
60
PDX
THREADING
ISO Metric
Partial Profile 55
Partial Profile 60
Type
Coated
IC
Full form
RE
PDY
CUTTING DEPTH GUIDE
55
PDX
IC
G041
G015
THREADING
MMT G-CLASS GROUND INSERTS
Order Number
MMT16ERA60
MMT16ERG60
MMT16ERAG60
MMT22ERN60
VP10MF
VP15TF
Coated
Thread
Tolerance
Partial Profile 60
Type
a a
a a
a
a
Dimensions (mm)
Pitch
mm
thread/inch
0.5 1.5
1.753.0
0.5 3.0
3.5 5.0
4816
148
488
7 5
IC
PDY
PDX
RE
9.525
9.525
9.525
12.7
3.44
3.44
3.44
4.64
0.8
1.2
1.2
1.7
0.9
1.7
1.7
2.5
0.05
0.27
0.08
0.53
Total
Cutting
Depth
(mm)
Geometry
Partial form
60
PDX
IC
Partial Profile 55
MMT16ERA55
MMT16ERG55
MMT16ERAG55
MMT22ERN55
4816
148
488
75
a a
a a
a
a
9.525
9.525
9.525
12.7
3.44
3.44
3.44
4.64
0.8
1.2
1.2
1.7
0.9
1.7
1.7
2.5
0.05
0.21
0.07
0.44
Partial form
55
PDX
THREADING
ISO Metric
a
a
a a
a a
a a
a a
a a
a a
a a
a
a
a
a
0.5
0.75
1.0
1.25
1.5
1.75
2.0
2.5
3.0
3.5
4.0
4.5
5.0
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
12.7
12.7
12.7
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
4.64
4.64
4.64
0.6
0.6
0.7
0.8
0.8
0.9
1.0
1.1
1.2
1.6
1.6
1.7
1.7
0.4
0.6
0.7
0.9
1.0
1.2
1.3
1.5
1.6
2.3
2.3
2.4
2.5
0.06
0.10
0.16
0.19
0.23
0.21
0.31
0.32
0.46
0.45
0.52
0.58
0.63
0.31
0.46
0.61
0.77
0.92
1.07
1.23
1.53
1.84
2.15
2.45
2.76
3.07
RE
PDY
IC
MMT16ER050ISO
MMT16ER075ISO
MMT16ER100ISO
MMT16ER125ISO
MMT16ER150ISO
MMT16ER175ISO
MMT16ER200ISO
MMT16ER250ISO
MMT16ER300ISO
MMT22ER350ISO
6g
MMT22ER400ISO
MMT22ER450ISO
MMT22ER500ISO
RE
PDY
Full form
60
PDX
RE
PDY
IC
IDENTIFICATION
MMT
16
Designation
050
Hand of Tool
Right
R
Diameter of
Inscribed Circle
(mm)
6.35
11
16
22
9.525
12.7
Application
E External
Internal
I
Pitch
050
075
100
125
150
175
200
250
300
350
400
450
500
G016
ISO
0.5mm
0.51.5mm
0.75mm A
or
4816 thread/inch
1.0mm
1.25mm
1.75 3.0mm
1.5mm
or
G
1.75mm
14 8 thread/inch
2.0mm
0.53.0mm
2.5mm
or
3.0mm AG
488 thread/inch
3.5mm
4.0mm
3.55.0mm
or
N
4.5mm
7 5 thread/inch
5.0mm
Threading Type
ISO ISO Metric
W Whitworth for BSW, BSP
BSPT BSPT
UN American UN
RD Round DIN 405
TR ISO Trapezoidal 30
ACME American ACME
UNJ UNJ
APBU API Buttress Casing
APRD API Round Casing&Tubing
NPT NPT
NPTF NPTF

CUTTING DEPTH GUIDE
G039
Order Number
MMT11IRA60
MMT16IRA60
MMT16IRG60
MMT16IRAG60
MMT22IRN60
a a
a a
a a
a
a
Dimensions (mm)
Pitch
mm
thread/inch
0.5 1.5
0.5 1.5
1.753.0
0.5 3.0
3.5 5.0
4816
4816
14 8
488
7 5
IC
PDY
PDX
RE
6.35
9.525
9.525
9.525
12.7
3.04
3.44
3.44
3.44
4.64
0.8
0.8
1.2
1.2
1.7
0.9
0.9
1.7
1.7
2.5
0.05
0.05
0.16
0.05
0.30
Total
Cutting
Depth
(mm)
Geometry
Partial form
RE
PDY
MMT11IRA55
MMT16IRA55
MMT16IRG55
MMT16IRAG55
MMT22IRN55
4816
4816
148
488
75
a a
a a
a a
a
a
6.35
9.525
9.525
9.525
12.7
3.04
3.44
3.44
3.44
4.64
0.8
0.8
1.2
1.2
1.7
0.9
0.9
1.7
1.7
2.5
0.05
0.05
0.21
0.07
0.44
6H
a
a
a a
a a
a a
a
a
a
a
a a
a a
a a
a a
a a
a a
a a
a
a
a
a
0.5
0.75
1.0
1.25
1.5
1.75
2.0
0.5
0.75
1.0
1.25
1.5
1.75
2.0
2.5
3.0
3.5
4.0
4.5
5.0
6.35
6.35
6.35
6.35
6.35
6.35
6.35
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
12.7
12.7
12.7
3.04
3.04
3.04
3.04
3.04
3.04
3.04
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
4.64
4.64
4.64
0.6
0.6
0.6
0.8
0.8
0.9
0.9
0.6
0.6
0.6
0.8
0.8
0.9
1.0
1.1
1.1
1.6
1.6
1.6
1.6
0.4
0.6
0.7
0.9
1.0
1.1
1.1
0.4
0.6
0.7
0.9
1.0
1.2
1.3
1.5
1.5
2.3
2.3
2.4
2.3
0.03
0.04
0.10
0.12
0.14
0.10
0.18
0.03
0.04
0.10
0.12
0.14
0.10
0.18
0.15
0.26
0.22
0.25
0.28
0.32
0.29
0.43
0.58
0.72
0.87
1.01
1.15
0.29
0.43
0.58
0.72
0.87
1.01
1.15
1.44
1.73
2.02
2.31
2.60
2.89
IC
Partial form
RE
55
PDX
PDY
MMT11IR050ISO
MMT11IR075ISO
MMT11IR100ISO
MMT11IR125ISO
MMT11IR150ISO
MMT11IR175ISO
MMT11IR200ISO
MMT16IR050ISO
MMT16IR075ISO
MMT16IR100ISO
MMT16IR125ISO
MMT16IR150ISO
MMT16IR175ISO
MMT16IR200ISO
MMT16IR250ISO
MMT16IR300ISO
MMT22IR350ISO
MMT22IR400ISO
MMT22IR450ISO
MMT22IR500ISO
60
PDX
IC
THREADING
Coated
VP10MF
VP15TF
Type
Partial Profile 60
Partial Profile 55
ISO Metric
Thread
Tolerance
Full form
CUTTING DEPTH GUIDE
RE
60
PDX
PDY
IC
G041
G017
THREADING
G018
Order Number
Medium Class A
VP10MF
VP15TF
Coated
MMT16ER320UN
MMT16ER280UN
MMT16ER240UN
MMT16ER200UN
MMT16ER180UN
MMT16ER160UN
MMT16ER140UN
MMT16ER130UN
MMT16ER120UN
MMT16ER110UN
MMT16ER100UN
2A MMT16ER090UN
MMT16ER080UN
MMT22ER070UN
MMT22ER060UN
MMT22ER050UN
Standard BSPT
Type
Round DIN 405
BSPT
THREADING
American UN
Thread
Tolerance
a
a
a
a
a
a a
a a
a
a a
a
a
a
a
a
a
a
MMT16ER280W
MMT16ER260W
MMT16ER200W
MMT16ER190W
MMT16ER180W
MMT16ER160W
MMT16ER140W
MMT16ER120W
MMT16ER110W
MMT16ER100W
MMT16ER090W
MMT16ER080W
MMT22ER070W
MMT22ER060W
MMT22ER050W
MMT16ER280BSPT
MMT16ER190BSPT
MMT16ER140BSPT
MMT16ER110BSPT
MMT16ER100RD
MMT16ER080RD
MMT16ER060RD
7h MMT22ER040RD
a
a
a a
a
a
a a
a
a a
a
a
a
a
a
a
a a
a a
a a
Dimensions (mm)
Pitch
mm
Total
Cutting
Depth
(mm)
Geometry
IC
PDY
PDX
RE
32
28
24
20
18
16
14
13
12
11
10
9
8
7
6
5
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
12.7
12.7
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
4.64
4.64
0.6
0.6
0.7
0.8
0.8
0.9
1.0
1.0
1.1
1.1
1.1
1.2
1.2
1.6
1.6
1.7
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.5
1.7
1.6
2.3
2.3
2.5
0.09
0.10
0.16
0.19
0.21
0.24
0.22
0.24
0.32
0.29
0.32
0.35
0.48
0.47
0.53
0.64
0.49
0.56
0.65
0.78
0.87
0.97
1.11
1.20
1.30
1.42
1.56
1.73
1.95
2.22
2.60
3.12
Full form
28
26
20
19
18
16
14
12
11
10
9
8
7
6
5
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
12.7
12.7
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
4.64
4.64
0.6
0.7
0.8
0.8
0.8
0.9
1.0
1.1
1.1
1.1
1.2
1.2
1.6
1.6
1.7
0.7
0.8
0.9
1.0
1.0
1.1
1.2
1.4
1.5
1.5
1.7
1.5
2.3
2.3
2.4
0.09
0.10
0.18
0.19
0.20
0.23
0.26
0.30
0.33
0.37
0.34
0.39
0.46
0.53
0.66
0.58
0.63
0.81
0.86
0.90
1.02
1.16
1.36
1.48
1.63
1.81
2.03
2.32
2.71
3.25
Full form
28
19
14
11
9.525
9.525
9.525
9.525
3.44
3.44
3.44
3.44
0.6
0.8
1.0
1.1
0.6
0.9
1.2
1.5
0.09
0.14
0.26
0.33
0.58
0.86
1.16
1.48
Full form
thread/inch
60
PDX
IC
55
PDX
a
a
a
10
8
6
4
9.525
9.525
9.525
9.525
3.44
3.44
3.44
3.44
1.1
1.4
1.5
2.2
1.2
1.3
1.7
2.3
0.60
0.75
1.00
1.51
1.27
1.59
2.12
3.18
RE
PDY
IC
55
PDX
RE
PDY
IC
S
a
RE
PDY
30
Full form
PDX
PDY
RE
IC

CUTTING DEPTH GUIDE
G039
Medium Class A
MMT11IR320UN
MMT11IR280UN
MMT11IR240UN
MMT11IR200UN
MMT11IR180UN
MMT11IR160UN
MMT11IR140UN
MMT16IR320UN
MMT16IR280UN
MMT16IR240UN
MMT16IR200UN
2B MMT16IR180UN
MMT16IR160UN
MMT16IR140UN
MMT16IR130UN
MMT16IR120UN
MMT16IR110UN
MMT16IR100UN
MMT16IR090UN
MMT16IR080UN
MMT22IR070UN
MMT22IR060UN
MMT22IR050UN
MMT11IR190W
MMT11IR140W
MMT16IR280W
MMT16IR260W
MMT16IR200W
MMT16IR190W
MMT16IR180W
MMT16IR160W
MMT16IR140W
MMT16IR120W
MMT16IR110W
MMT16IR100W
MMT16IR090W
MMT16IR080W
MMT22IR070W
MMT22IR060W
MMT22IR050W
MMT11IR190BSPT
MMT11IR140BSPT
MMT16IR190BSPT
MMT16IR140BSPT
MMT16IR110BSPT
a
a
a
a
a
a
a
a
a
a
a
a
a a
a a
a
a a
a
a
a
a
a
a
a
a
a
a
a
a
a a
a
a
a a
a
a a
a
a
a
a
a
a
a
a
MMT16IR100RD
MMT16IR080RD
MMT16IR060RD
7H MMT22IR040RD
a a
a a
a a
Dimensions (mm)
Pitch
mm
thread/inch
32
28
24
20
18
16
14
32
28
24
20
18
16
14
13
12
11
10
9
8
7
6
5
19
14
28
26
20
19
18
16
14
12
11
10
9
8
7
6
5
19
14
19
14
11
IC
PDY
PDX
RE
6.35
6.35
6.35
6.35
6.35
6.35
6.35
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
12.7
12.7
6.35
6.35
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
12.7
12.7
6.35
6.35
9.525
9.525
9.525
3.04
3.04
3.04
3.04
3.04
3.04
3.04
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
4.64
4.64
3.04
3.04
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
4.64
4.64
3.04
3.04
3.44
3.44
3.44
0.6
0.6
0.7
0.8
0.8
0.9
0.9
0.6
0.6
0.7
0.8
0.8
0.9
0.9
1.0
1.1
1.1
1.1
1.2
1.1
1.6
1.6
1.6
0.8
0.9
0.6
0.7
0.8
0.8
0.8
0.9
1.0
1.1
1.1
1.1
1.2
1.2
1.6
1.6
1.7
0.8
0.9
0.8
1.0
1.1
0.6
0.7
0.8
0.9
1.0
1.1
1.1
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.5
1.7
1.5
2.3
2.3
2.3
1.0
1.1
0.7
0.8
0.9
1.0
1.0
1.1
1.2
1.4
1.5
1.5
1.7
1.5
2.3
2.3
2.4
0.9
1.0
0.9
1.2
1.5
0.04
0.05
0.09
0.11
0.12
0.14
0.11
0.04
0.05
0.09
0.11
0.12
0.14
0.11
0.10
0.18
0.13
0.15
0.17
0.27
0.23
0.26
0.32
0.19
0.26
0.09
0.10
0.18
0.19
0.20
0.23
0.26
0.30
0.33
0.37
0.34
0.39
0.46
0.53
0.66
0.14
0.26
0.14
0.26
0.33
Total
Cutting
Depth
(mm)
0.46
0.52
0.61
0.73
0.81
0.92
1.05
0.46
0.52
0.61
0.73
0.81
0.92
1.05
1.13
1.22
1.33
1.47
1.63
1.83
2.09
2.44
2.93
0.86
1.16
0.58
0.63
0.81
0.86
0.90
1.02
1.16
1.36
1.48
1.63
1.81
2.03
2.32
2.71
3.25
0.86
1.16
0.86
1.16
1.48
Geometry
Full form
RE
PDY
a
a
10
8
6
4
9.525
9.525
9.525
12.7
3.44
3.44
3.44
4.64
1.1
1.4
1.4
2.2
1.2
1.4
1.5
2.3
0.55
0.70
0.93
1.40
1.27
1.59
2.12
3.18
IC
Full form
RE
55
PDX
PDY
IC
Full form
RE
55
PDX
PDY
60
PDX
THREADING
Order Number
VP10MF
VP15TF
Coated
Standard BSPT
Type
American UN
BSPT
Round DIN 405
Thread
Tolerance
IC
Full form
RE
PDX
PDY
CUTTING DEPTH GUIDE
30
IC
G041
G019
THREADING
G020
Order Number
VP10MF
Coated
MMT16ER150TR
MMT16ER200TR
MMT16ER300TR
7e MMT22ER400TR
MMT22ER500TR
a
a
a
a
a
Dimensions (mm)
Pitch
mm
IC
PDY
PDX
RE
9.525
9.525
9.525
12.7
12.7
3.44
3.44
3.44
4.64
4.64
1.0
1.1
1.3
1.7
2.1
1.1
1.3
1.5
1.9
2.5
0.08
0.15
0.15
0.15
0.15
thread/inch
1.5
2.0
3.0
4.0
5.0
Total
Cutting
Depth
(mm)
0.90
1.25
1.75
2.25
2.75
Geometry
Semi-full formPDX
RE
PDY
30
RE
IC
MMT16ER120ACME
MMT16ER100ACME
MMT16ER080ACME
3G MMT22ER060ACME
MMT22ER050ACME
a
a
a
a
a
12
10
8
6
5
9.525
9.525
9.525
12.7
12.7
3.44
3.44
3.44
4.64
4.64
1.1
1.3
1.4
1.8
2.0
1.2
1.4
1.5
2.1
2.3
0.08
0.08
0.10
0.10
0.10
1.19
1.52
1.84
2.37
2.79
Semi-full formPDX
RE
PDY
29
RE
IC
S
a
a
a
a
a
a
a
a
a
a
a
32
28
24
20
18
16
14
12
10
8
5
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
9.525
12.7
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
3.44
4.64
0.6
0.7
0.7
0.8
0.8
0.9
1.0
1.1
1.2
1.2
3.1
0.7
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.5
1.6
1.9
0.13
0.14
0.17
0.20
0.22
0.25
0.29
0.33
0.40
0.51
0.18
0.46
0.52
0.61
0.73
0.81
0.92
1.05
1.22
1.47
1.83
1.55
Full form
60
PDX
IC
Full form
13
R0.74
PDY
PDX
RE
IC
Standard NPT
Standard API RD
MMT16ER100APRD
MMT16ER080APRD
a
a
10
8
9.525
9.525
3.44
3.44
1.2
1.3
1.4
1.5
0.34
0.41
1.41
1.81
Full form
60
PDX
RE
PDY
IC
MMT16ER270NPT
MMT16ER180NPT
MMT16ER140NPT
MMT16ER115NPT
MMT16ER080NPT
a
a
a
a
a
27
18
14
11.5
8
9.525
9.525
9.525
9.525
9.525
3.44
3.44
3.44
3.44
3.44
0.7
0.8
0.9
1.1
1.3
0.8
1.0
1.2
1.5
1.8
0.04
0.08
0.09
0.11
0.14
0.66
1.01
1.33
1.64
2.42
Full form
60
PDX
PDY
a
a
a
a
a
27
18
14
11.5
8
9.525
9.525
9.525
9.525
9.525
3.44
3.44
3.44
3.44
3.44
0.7
0.8
0.9
1.1
1.3
0.8
1.0
1.2
1.5
1.8
0.04
0.04
0.04
0.04
0.04
0.64
1.00
1.35
1.63
2.38
Full form
60
PDX
PDY
RE
IC
MMT16ER270NPTF
MMT16ER180NPTF
MMT16ER140NPTF
MMT16ER115NPTF
MMT16ER080NPTF
RE
PDY
Standard API
MMT16ER320UNJ
MMT16ER280UNJ
MMT16ER240UNJ
MMT16ER200UNJ
MMT16ER180UNJ
3A
MMT16ER160UNJ
MMT16ER140UNJ
MMT16ER120UNJ
MMT16ER100UNJ
MMT16ER080UNJ
MMT22ER050APBU
Class 2
Type
UNJ
American NPTF
American NPT
API Round Casing&Tubing API Buttress Casing
THREADING
American ACME
ISO Trapezoidal 30
Thread
Tolerance
RE
IC

CUTTING DEPTH GUIDE
G040
MMT16IR150TR
MMT16IR200TR
MMT16IR300TR
7H MMT22IR400TR
MMT22IR500TR
a
a
a
a
a
Pitch
mm
thread/inch
1.5
2.0
3.0
4.0
5.0
IC
PDY
PDX
RE
9.525
9.525
9.525
12.7
12.7
3.44
3.44
3.44
4.64
4.64
1.0
1.1
1.3
1.7
2.1
1.1
1.3
1.5
1.9
2.5
0.08
0.15
0.15
0.15
0.15
Total
Cutting
Depth
(mm)
0.90
1.25
1.75
2.25
2.75
Geometry
a
a
a
a
a
12
10
8
6
5
9.525
9.525
9.525
12.7
12.7
3.44
3.44
3.44
4.64
4.64
1.2
1.2
1.4
1.8
2.0
1.3
1.3
1.5
2.1
2.3
0.05
0.08
0.10
0.10
0.10
1.19
1.52
1.84
2.37
2.79
RE
RE 30
MMT16IR120ACME
MMT16IR100ACME
MMT16IR080ACME
3G MMT22IR060ACME
MMT22IR050ACME
PDX
Semi-full form
PDY
IC
PDX
Semi-full form
RE
RE 29
PDY
IC
THREADING
Order Number
VP10MF
Type
ISO Trapezoidal 30
When machining an internal UNJ thread, cut an internal hole with the appropriate diameter.
Then machine with 60 American UN. In this case, a full form type insert cannot be used.
12.7
4.64
2.8
1.9
0.18
1.55
Full form
Standard API
MMT22IR050APBU
Standard API RD
Standard NPT
13
R0.74
PDX RE
PDY
Class 2
API Round Casing&Tubing API Buttress Casing

American NPT
American NPTF
Dimensions (mm)
Coated
UNJ
American ACME
Thread
Tolerance
MMT16IR100APRD
MMT16IR080APRD
a
a
10
8
9.525
9.525
3.44
3.44
1.2
1.3
1.4
1.5
0.34
0.41
1.41
1.81
Full form
a
a
a
a
a
27
18
14
11.5
8
9.525
9.525
9.525
9.525
9.525
3.44
3.44
3.44
3.44
3.44
0.7
0.8
0.9
1.1
1.3
0.8
1.0
1.2
1.5
1.8
0.04
0.08
0.09
0.11
0.14
0.66
1.01
1.33
1.64
2.42
a
a
a
14
11.5
8
9.525
9.525
9.525
3.44
3.44
3.44
0.9
1.1
1.3
1.2
1.5
1.8
0.04
0.04
0.04
1.35
1.63
2.38
PDY
IC
Full form
60
PDX
RE
MMT16IR140NPTF
MMT16IR115NPTF
MMT16IR080NPTF
60
PDX
RE
MMT16IR270NPT
MMT16IR180NPT
MMT16IR140NPT
MMT16IR115NPT
MMT16IR080NPT
IC
IC
Full form
CUTTING DEPTH GUIDE
60
PDX
RE
PDY
PDY
IC
G042
G021
EXTERNAL THREADING
MTHOLDER
MTH
a Clamp-on type.
a Positive insert suffers
from negligible chattering

and thus produces good finished surfaces.
a Thread pitch < 4.5mm.
WF
HBKW
External threading
LF
5
MTHR/L1616H4
H
H3
HF
HF
21
Stock
(Note) Cutting in the opposite

direction is not possible.
Order Number
Dimensions (mm)
Insert Number
Clamp
Bridge
Clamp
Screw
Spring
Wrench
16 16 100 16 19 13.8 3
MTK1R/L
HBH06020
MES3
HKY40R
20 20 125 20
17.8
MTK1R/L
HBH06020
MES3
HKY40R
25 25 150 25
22.8
MTK1R/L
HBH06020
MES3
HKY40R
R L
MTHR/L1616H4
a a
MTHR/L2020K4
a a
MTHR/L2525M4
a a
MTTR/L43pppp
LF HF H3 WF HBKW
Clamp Torque (N m) : HBH06020=7.0
MT1
External threading
WF
THREADING
LH
LF
HF
Stock

Order Number
Dimensions (mm)
Insert Number
R L
LH
HF
WF
Clamp
Bridge
Clamp
Screw
Spring
Wrench
MT1R/L2020K4
a a
20
20 125 30
20
25
MTK1R/L
HBH06020
MES3
HKY40R
MT1R/L2525M4
a a
25
25 150 30
25
32
MTK1R/L
HBH06020
MES3
HKY40R
MT1R/L3232P4
a a
32
32 170 30
32
40
MTK1R/L
HBH06020
MES3
HKY40R
MTTR/L43pppp
LF
Clamp Torque (N m) : HBH06020=7.0

Work Material
Hardness
P
Mild Steel
Carbon Steel
Alloy Steel
180 280HB
Cutting Speed
(m/min)
UP20M
140 (100180)
NX2525
200 (150250)
UTi20T
120 (100150)
UP20M
120 (100150)
NX2525
170 (150200)
UTi20T
100 (70120)
Work Material
Stainless Steel
Hardness
< 200HB
K
Gray Cast Iron

G022
< 180HB
Grade
Tensile Strength
< 350MPa
Grade
Cutting Speed
(m/min)
UP20M
120 (80 150)
UTi20T
100 (70 130)
UP20M
80 (60 100)
UTi20T
80 (60 100)
HTi10
100 (70 130)
INSERTS
Dimensions (mm)
4.76
0.1
a a
2.0 2.5
12.7
4.76
0.2
4.76
0.2
a a
2.0 2.5
3.0 3.5
12.7
12.7
4.76
0.3
G
G
12.7
12.7
4.76
4.76
0.3
0.4
G
G
G
3.0 3.5
4.0 4.5
(28 10)
(16 8)
(11 8)
G
G
0
0.1
12.7
12.7
12.7
4.76
4.76
4.76
0.1
0.2
0.3
MTTR/L(60)
RE
MTTR(55)
RE
y STANDARD OF DEPTH
a METRIC SCREW THREAD
OF CUT
P (Pitch)
0.75
0.46
h2
0.35
r (Corner Radius) 0.11
1 0.18
2 0.13
3 0.10
4 0.05
5
6
7
8
9
10
11
12
13
14
h1
a The chart on the right shows the cutting
Number of Passes
depths when machining external ISO

metric screw threads.
a When you use cermet grades or cut
stainless steel, please increase the
number of passes by 2 3 times.
H/4
h2
h1
THREADING
IC
4.76
4.76
12.7
12.7
12.7
Geometry
IC
a a
0.8
1.0 1.75
1.0 1.75
RE
a a
60
IC
55
a
a
G
G
UTi20T
HTi10
NX2525
MTTR436000
MTTR436001
MTTL436001
MTTR436002
MTTL436002
MTTR436003
MTTL436003
MTTR436004
MTTR435501
MTTR435502
MTTR435503
Class
Order Number
ISO
Pitch mm
(thread/inch)
UP20M
Partial Profile 55
Partial Profile 60
Type
1.00
0.61
0.47
0.14
0.20
0.15
0.10
0.10
0.06
1.25
0.77
0.59
0.18
0.20
0.18
0.12
0.12
0.10
0.05
1.50
0.92
0.70
0.22
0.25
0.20
0.15
0.15
0.10
0.07
1.75
1.07
0.82
0.25
0.25
0.20
0.20
0.15
0.12
0.10
0.05
2.00
1.23
0.94
0.29
0.25
0.25
0.20
0.15
0.15
0.10
0.08
0.05
2.50
1.53
1.17
0.36
0.30
0.25
0.20
0.20
0.15
0.10
0.10
0.10
0.08
0.05
3.00
1.84
1.41
0.43
0.30
0.25
0.25
0.20
0.20
0.15
0.15
0.10
0.10
0.09
0.05
3.50
2.15
1.65
0.50
0.35
0.30
0.25
0.20
0.20
0.20
0.15
0.15
0.10
0.10
0.10
0.05
4.00
2.45
1.87
0.58
0.35
0.30
0.25
0.25
0.25
0.20
0.20
0.15
0.15
0.10
0.10
0.10
0.05
4.50
2.76
2.11
0.65
0.40
0.35
0.30
0.25
0.25
0.20
0.20
0.15
0.15
0.15
0.10
0.10
0.10
0.06
(Note) The first pass causes a high load on the cutting edge. In order to avoid damage, keep the
depth of cut to 0.4 0.5mm maximum.
SPARE PARTS
P001
G023
EXTERNAL THREADING
SMGHOLDER
SMGH
a Screw-on type.
a Positive insert suffers from negligible chattering.
a Suitable for narrow grooving and threading.
a Thread pitch < 2.0 mm.
Stock
a
HF
SMGHR1010E16 : HBH=4
2.5
HF
THREADING
SMGHR1212F16
3.5
LF

Insert Number
Threading
R
a
LH
SMGHR1212F16 : HBH=2

SMGHR1010E16
HBH
LH
Order Number
130WF
60
Grooving
B
F2
Threading
2.5
External threading, Grooving
Dimensions (mm)
Grooving
SMGTR16X2ppp
SMGTR16X2pppC
LH HF WF F2 Clamp Screw
Wrench
LF
10
10
70 16.5 10
12 11.7 FC400890T
TKY10F
12
12
80 16.5 12
16 15.7 FC400890T
TKY10F
16
16 100 20
16
20 19.7 FC400890T
TKY10F
SMGHR1616H16
SMGHR2020K16
20
20 125 20
20
25 24.7 FC400890T
TKY10F
SMGHR2525M16
25
25 150 20
25
32 31.7 FC400890T
TKY10F
SMTTR160360pp
y STANDARD OF DEPTH
OF CUT
P (Pitch)
0.75
1.00
1.25
1.50
1.75
2.00
h1
0.46
0.61
0.77
0.92
1.07
1.23
h2
0.35
0.47
0.59
0.70
0.82
0.94
r (Corner Radius)
0.11
0.14
0.18
0.22
0.25
0.29
0.18
0.20
0.20
0.25
0.25
0.25
0.13
0.15
0.18
0.20
0.20
0.25
0.10
0.10
0.12
0.15
0.20
0.20
0.05
0.10
0.12
0.15
0.15
0.15
0.06
0.10
0.10
0.12
0.15
0.05
0.07
0.10
0.10
0.05
0.08
Number of Passes

5
6
7
8
H/4
h2
h1
0.05
9

Work Material
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180 280HB
G024
Hardness
Grade
Cutting Speed
(m/min)
NX2525
200 (150 250)
UTi20T
120 (100 150)
NX2525
170 (150 200)
UTi20T
100 (70 120)
Work Material
M
Stainless Steel
Gray Cast Iron
Hardness
Grade
Cutting Speed
(m/min)
< 200HB
UTi20T
100 (70 130)
Tensile Strength
UTi20T
80 (60 100)
HTi10
100 (70 130)
< 350MPa
SMT INSERTS (Threading)

Dimensions (mm)
Thread Pitch
(mm)
UTi20T
Order Number
1.0 1.5
0.1
1.75 2.0
0.2
60
RE
9.525
SMTTR16036001
SMTTR16036002
Geometry
RE
3.18
Carbide
SMG INSERTS (Grooving)

Dimensions (mm)
S
BCH
0.5
1.5
9.525
SMGTR16X2060
a a
0.6
1.5
9.525
SMGTR16X2050C
a a
0.5
1.5
9.525
0.05
SMGTR16X2060C
a a
0.6
1.5
9.525
0.05
SMGTR16X2070C
a a
0.7
9.525
0.05
SMGTR16X2075C
a a
0.75
9.525
0.05
SMGTR16X2080C
a a
0.8
9.525
0.1
SMGTR16X2090C
a a
0.9
9.525
0.1
SMGTR16X2095C
a a
0.95
9.525
0.1
SMGTR16X2100C
a a
2.5
9.525
0.1
SMGTR16X2110C
a a
1.1
2.5
9.525
0.1
SMGTR16X2120C
a a
1.2
2.5
9.525
0.1
SMGTR16X2130C
a a
1.3
2.5
9.525
0.1
Geometry
THREADING
IC
4.5
BCH
PDPT
S
PDPT
IC
CW
CW +0.05
0
SMGTR16X2050
UTi20T
HTi10
Order Number
NX2525
Cermet Carbide
SPARE PARTS
P001
G025
INTERNAL THREADING
MICRO-MINI TWIN
F2
DMIN
PDX
PDX
PDX
PDX
F2
WF
WF
RE
y CT STANDARD
DCON
LU
H
LF
L19
60
Threads
Order Number
Micro Grain
Coated
Carbide
Breaker
Stock
THREADING
TF15 VP15TF
Thread
Pitch
(mm)
Without
> M4
0.5 1.0
Without
> M4
0.5 1.0
CT03RS-M4B
With
> M4
0.5 1.0
CT0407RS-M6
Without
> M6
0.75 1.25
CT04RS-M6
Without
> M6
0.75 1.25
CT04RS-M6B
With
> M6
0.75 1.25
CT0511RS-M8
Without
> M8
0.75 1.5
CT05RS-M8
Without
> M8
0.75 1.5
CT05RS-M8B
With
> M8
0.75 1.5
CT0611RS-M10
Without
> M10
0.75 1.75
0.75 1.75
0.75 1.75
CT0305RS-M4
CT03RS-M4
CT06RS-M10
Without
> M10
CT06RS-M10B
With
> M10
G026
Metric Screw
Dimensions (mm)
Unified Coarse Screw

Thread
> NO.8-32UNC
> NO.8-36UNF
> 1/4-20UNC
> 1/4-28UNF
> 5/16-18UNC
> 5/16-24UNF
> 3/8-16UNC
> 3/8-24UNF
Pitch
(thread/inch) DMIN RE DCON LF LU L19 WF PDX F2
36 24 3
0.03 3
50
5.2 6
1.3 0.6 1.2 2.7
36 24 3
0.03 3
50 10.2 6
1.3 0.6 1.2 2.7
36 24 3
0.03 3
50 10.2 6
1.3 0.6 1.2 2.7
28 20 4.5 0.05 4
60
7.6 7
1.8 0.8 1.7 3.6
28 20 4.5 0.05 4
60 15.6 7
1.8 0.8 1.7 3.6
28 20 4.5 0.05 4
60 15.6 7
1.8 0.8 1.7 3.6
24 18 6
0.05 5
70 11
2.3 1
2.2 4.5
24 18 6
0.05 5
70 21
2.3 1
2.2 4.5
24 18 6
0.05 5
70 21
2.3 1
2.2 4.5
24 16 7
0.05 6
75 11
2.8 1
2.2 5.4
24 16 7
0.05 6
75 21
2.8 1
2.2 5.4
24 16 7
0.05 6
75 21
2.8 1
2.2 5.4

Work Material
Carbon Steel
Alloy Steel
50 (30 80)
Stainless Steel
50 (30 80)
Cast Iron
50 (30 80)
Non-Ferrous Metal
80 (50 100)
Recommended Tool Overhang (mm)

Micro-Mini Twin
CT
LU+2(mm)
Holder
(Note 1) Wet cutting is recommended.

(Note 2) Pay special attention to
machining of small
diameters at high
revolutions as the feed rate
cannot keep up with the
speed.

a When using a holder for general purpose / small automatic lathe:
Fig.1
Internal Face of the Holder
Insert Direction
sWhen using this type of holder, there is a possibility that damage to the shank and the 2nd cutting
eWhen using Mitsubishi holders
screw is removed prior to machining. The set torque value for clamping screw is 2.0 N m.
Fig.2
Cutting Edge
3rd Clamping Screw
Insert Point
THREADING
aTo avoid chipping of the 2nd cutting edge take care when inserting the boring bar into the holder.
may chip.
2nd Cutting Edge
a When using a square type holder:
aWhen installing the boring bar into the holder, tighten the clamp screws after ensuring the flats on
sMake sure that the clamping screws are tightened to the recommended values.
dDo not tighten the clamp screw without a bar in place, otherwise the bridge will be deformed.
Fig.3
Insert The Reference Plane

of Square Type Holder
Tighten the clamping screw ensuring making the
micro-mini twin boring bars in contact with the
reference plane of square type holder.
SPARE PARTS
P001
G027
INTERNAL THREADING
ROUND TYPE HOLDER
5
3-M4 x 0.7
S2
BD
DCON
S1
S1
S2
3-M4 x 0.7
BD
DCB
10
S3
20
10
LF
THREADING
Order Number
*2
*2
*2
*2
Stock

Dimensions (mm)
DCON DCB
BD
LF
S1
S2
S3
Micro-Mini Twin
CT
G028
RBH190ppN
*1
Clamp
Screw
z x c v
Wrench Torque
(Nm)
RBH15830N
15.875
15
100
10
10
0305RS-M4, 03RS-M4(B)
A A A HKY20F
2.0
RBH15840N
15.875
15
100
15
15
0407RS-M6, 04RS-M6(B)
A A A HKY20F
2.0
RBH15850N
15.875
15
100
15
15
0511RS-M8, 05RS-M8(B)
A A A HKY20F
2.0
RBH15860N
15.875
15
100
15
15
0611RS-M10, 06RS-M10(B)
A A A HKY20F
2.0
RBH1630N
16
15
100
10
10
0305RS-M4, 03RS-M4(B)
A A A HKY20F
2.0
RBH1640N
16
15
100
15
15
0407RS-M6, 04RS-M6(B)
A A A HKY20F
2.0
RBH1650N
16
15
100
15
15
0511RS-M8, 05RS-M8(B)
A A A HKY20F
2.0
RBH1660N
16
15
100
15
15
0611RS-M10, 06RS-M10(B)
A A A HKY20F
2.0
RBH19030N
19.05
18
125
10
10
0305RS-M4, 03RS-M4(B)
B B B HKY20F
2.0
RBH19040N
19.05
18
125
15
15
0407RS-M6, 04RS-M6(B)
B B B HKY20F
2.0
RBH19050N
19.05
18
125
15
15
0511RS-M8, 05RS-M8(B)
B B B HKY20F
2.0
RBH19060N
19.05
18
125
15
15
0611RS-M10, 06RS-M10(B)
B B B HKY20F
2.0
RBH2030N
20
12
125
10
10
0305RS-M4, 03RS-M4(B)
A A B HKY20F
2.0
RBH2040N
20
13
125
15
15
0407RS-M6, 04RS-M6(B)
A B B HKY20F
2.0
RBH2050N
20
14
125
15
15
0511RS-M8, 05RS-M8(B)
A B B HKY20F
2.0
RBH2060N
20
15
125
15
15
0611RS-M10, 06RS-M10(B)
A B B HKY20F
2.0
RBH2230N
22
12
125
10
10
10
0305RS-M4, 03RS-M4(B)
A B C A HKY20F
2.0
RBH2240N
22
13
125
15
15
12.5
0407RS-M6, 04RS-M6(B)
A B B A HKY20F
2.0
RBH2250N
22
14
125
15
15
12.5
0511RS-M8, 05RS-M8(B)
A B B A HKY20F
2.0
RBH2260N
22
15
125
15
15
15
0611RS-M10, 06RS-M10(B)
A B B A HKY20F
2.0
RBH2530N
25
12
150
10
10
0305RS-M4, 03RS-M4(B)
A B C HKY20F
2.0
RBH2540N
25
13
150
15
15
0407RS-M6, 04RS-M6(B)
A C C HKY20F
2.0
RBH2550N
25
14
150
15
15
0511RS-M8, 05RS-M8(B)
A C C HKY20F
2.0
RBH2560N
25
15
150
15
15
0611RS-M10, 06RS-M10(B)
A C C HKY20F
2.0
RBH25430N
25.4
12
150
10
10
0305RS-M4, 03RS-M4(B)
A B C HKY20F
2.0
RBH25440N
25.4
13
150
15
15
0407RS-M6, 04RS-M6(B)
A C C HKY20F
2.0
RBH25450N
25.4
14
150
15
15
0511RS-M8, 05RS-M8(B)
A C C HKY20F
2.0
RBH25460N
25.4
15
150
15
15
0611RS-M10, 06RS-M10(B)
A C C HKY20F
2.0
number of clamp screw

*12 Order
*
A=HSS04004, B=HSS04006, C=HSS04008
Conventional Order
Number
Revised Order
Number
RBH1930N
RBH19030N
RBH1940N
RBH19040N
RBH1950N
RBH19050N
RBH1960N
RBH19060N
x
LF
SQUARE TYPE HOLDER
10 (Clamp)
WF
45
20
100
Order Number
Dimensions (mm)
Micro-Mini Twin CT
L24
Micro-Mini Twin
CT
Clamp
Screw
Torque
(Nm)
Wrench
WF
13.8
13.8
13 17.5(14)
0305RS-M4, 03RS-M4(B)
HSC05012 HKY40R
9.5
0407RS-M6, 04RS-M6(B)
SBH1030R
SBH1040R
14.7
14.8
18.5 22(19.5)
HSC05012 HKY40R
9.5
SBH1050R
15.6
15.8
24 26.5(25)
0511RS-M8, 05RS-M8(B)
HSC05012 HKY40R
9.5
SBH1060R
16.8
24 31.5(25)
0611RS-M10, 06RS-M10(B)
HSC05012 HKY40R
9.5
16.5
L24 is the length of overhang for sufficient clamping, and ( ) is the recommended length for machining of carbon and alloy steel.
SPARE PARTS
THREADING
Stock
10
10
L24
P001
G029
INTERNAL THREADING
FSL51

a Screw-on type.
a Applicable to threading, grooving.
a Thread pitch 1.5 3.5mm.
Internal threading, Grooving
1Corner Type
(FSL5108R, 5110R)
LU
LF
10
WF
2 Corner Type
(FSL5112R, 5114R, 5116R)
LU
H
LF
DCON
Stock

Insert Number
*2
Dimensions (mm)
DMIN 1 Clamp Screw
Wrench
Threading
Grooving
DCON
LF
LU
WF
FSL5108R
MLT1001L
MLG10ppL
125
30
4.8
10
TS25
TKY08F
FSL5110R
MLT1001L
MLG10ppL
10
150
40
5.8
12
TS25
TKY08F
FSL5112R
MLT1401L
MLG14ppL
12
180
50
6.8
10.8
14
TS32
TKY08F
FSL5114R
MLT1401L
MLG14ppL
14
180
60
7.8
12.4
16
TS32
TKY08F
FSL5116R
MLT2001L
MLG20ppL
16
200
70
9.7
14
20
TS43
TKY15F
: Min.Cutting Diameter
*12 DMIN
*
FSL52
(Carbide shank) Internal threading, Grooving
1Corner Type
(FSL5208R, 5210R)
LU
LF
WF
10
2 Corner Type
(FSL5212R, 5214R, 5216R)
LU
LF

DCON

2
Stock
Order Number
DCON
WF
THREADING
2
5

Order Number
DCON
WF
TYPE
BORING BARS
Insert Number
Dimensions (mm)
DMIN 1 Clamp Screw
Wrench
Threading
Grooving
DCON
LF
LU
WF
FSL5208R
MLT1001L
MLG10ppL
125
60
4.8
10
TS25
TKY08F
FSL5210R
MLT1001L
MLG10ppL
10
150
70
5.8
12
TS25
TKY08F
FSL5212R
MLT1401L
MLG14ppL
12
180
80
6.8
11
14
TS32
TKY08F
FSL5214R
MLT1401L
MLG14ppL
14
180
85
7.8
12
16
TS32
TKY08F
FSL5216R
MLT2001L
MLG20ppL
16
200
115
9.7
14
20
TS43
TKY15F
: Min.Cutting Diameter
*12 DMIN
*

Work Material
Mild Steel
Carbon Steel
Alloy Steel
G030
Hardness
< 180HB
180 280HB

Grade
Cutting Speed
(m/min)
UP20M
140 (100 180)
UTi20T
120 (100 150)
UP20M
120 (100 150)
UTi20T
100 (70 120)
Work Material
M
K
Stainless Steel
Gray Cast Iron
Hardness
< 200HB
Tensile Strength
< 350MPa
Grade
Cutting Speed
(m/min)
UP20M
120 (80 150)
UTi20T
100 (70 130)
UP20M
80 (60 100)
UTi20T
80 (60 100)
INSERTS
Dimensions (mm)
L
W1 PDPT
Pitch 1.5 2.0 7

5
Pitch 1.5 2.5 11.8 6.5
Pitch 1.5 3.5 16.8 9.03
BCH
RE
2.38
4.76
6.35
0.1
0.1
0.1
Geometry
MLT
60
UTi20T
MLT1001L
MLT1401L
MLT2001L
Pitch and
CW
(mm)
Order Number
UP20M
RE
L
15
1.2
1.5
2
a
a
5
5
5
1.0
1.0
1.0
2.38
2.38
2.38
0.1
0.1
0.1
MLG...L
PDPT
7
7
7
MLG1012L
MLG1015L
MLG1020L
CW 0.025
W1
Threading
Type
Coated Carbide
BCH
L
2.0
2.0
4.76
4.76
0.1
0.1
11.8 6.5
2.0
4.76
0.1
16.8 9.03
3.0
6.35
0.1
16.8 9.03
3.0
6.35
0.1
16.8 9.03
3.0
6.35
0.1
PDPT
BCH
L
20
W1
MLG...L
THREADING
W1
11.8 6.5
11.8 6.5
1.5
2
CW 0.025
MLG1415L
MLG1420L
MLG1430L
MLG2020L
MLG2030L
MLG2040L
Grooving
15
y STANDARD OF DEPTH
OF CUT
P (Pitch)
h1

H/4
Number of Passes
H
h2
h1
h2
r (Corner Radius)
1
2
3
4
5
6
7
8
9
10
11
12
0.75
0.43
1.00
0.58
1.25
0.72
1.50
0.87
1.75
1.01
2.00
1.15
2.50
1.44
3.00
1.73
3.50
2.02
0.38
0.05
0.51
0.07
0.63
0.09
0.76
0.11
0.88
0.13
1.01
0.14
1.21
0.18
1.51
0.22
1.77
0.25
0.10
0.10
0.10
0.08
0.05
0.15
0.13
0.10
0.10
0.05
0.05
0.18
0.15
0.12
0.12
0.10
0.05
0.20
0.20
0.15
0.15
0.10
0.07
0.23
0.20
0.20
0.15
0.10
0.08
0.05
0.25
0.20
0.15
0.15
0.15
0.10
0.10
0.05
0.25
0.22
0.20
0.20
0.15
0.10
0.10
0.10
0.07
0.05
0.25
0.25
0.22
0.20
0.20
0.15
0.12
0.10
0.10
0.09
0.05
0.30
0.25
0.22
0.20
0.20
0.20
0.15
0.15
0.10
0.10
0.10
0.05
SPARE PARTS
P001
G031
INTERNAL THREADING
DPT2
a Minimum cutting diameter

a Pin lock type.
a Thread pitch < 4.5mm.
40mm.
Internal threading
WF
BD
TYPE
BORING HEAD
LF
RE
Stock

1
Order Number
DPT2132R
DPT2140R
Dimensions (mm)
Insert Number
MTTL4355pp
MTTL4360pp
BD
LF
WF
DMIN 2
RE
Lock Pin
32
40
20
40
0.1
40
50
25
50
0.1
Lock Screw Stop Ring
Wrench
P21S
HSP08014
E01
HKY40R
P21S
HSP08014
E01
HKY40R
THREADING
Torque (N m) : HSP08014=7.0
*12 Clamp
DMIN : Min.Cutting Diameter
*
y STANDARD OF DEPTH

P (Pitch)
OF CUT
0.75
0.43
h2
0.38
r (Corner Radius) 0.05
1 0.10
2 0.10
3 0.10
4 0.08
5 0.05
6
7
8
9
10
11
12
13
14
h1
Number of Passes

H/4
h2
h1
1.00
0.58
0.51
0.07
0.15
0.13
0.10
0.10
0.05
0.05
1.25
0.72
0.63
0.09
0.18
0.15
0.12
0.12
0.10
0.05
1.50
0.87
0.76
0.11
0.20
0.20
0.15
0.15
0.10
0.07
1.75
1.01
0.88
0.13
0.23
0.20
0.20
0.15
0.10
0.08
0.05
2.00
1.15
1.01
0.14
0.25
0.20
0.15
0.15
0.15
0.10
0.10
0.05
2.50
1.44
1.21
0.18
0.25
0.22
0.20
0.20
0.15
0.10
0.10
0.10
0.07
0.05
3.00
1.73
1.51
0.22
0.25
0.25
0.22
0.20
0.20
0.15
0.12
0.10
0.10
0.09
0.05
3.50
2.02
1.77
0.25
0.30
0.25
0.22
0.20
0.20
0.20
0.15
0.15
0.10
0.10
0.10
0.05
4.00
2.31
2.02
0.29
0.30
0.25
0.25
0.25
0.23
0.20
0.20
0.15
0.15
0.10
0.10
0.08
0.05
4.50
2.60
2.28
0.32
0.35
0.30
0.25
0.25
0.25
0.20
0.20
0.15
0.15
0.15
0.10
0.10
0.10
0.05

Work Material
Grade
UP20M
140 (100 180)
< 180HB
NX2525
200 (150 250)
P
Mild Steel
Carbon Steel
Alloy Steel
G032
Cutting Speed
(m/min)
Hardness
180 280HB

UTi20T
120 (100 150)
UP20M
120 (100 150)
NX2525
170 (150 200)
UTi20T
100 (70 120)
Work Material
Stainless Steel
Hardness
< 200HB
K
Gray Cast Iron
Tensile Strength
< 350MPa
Grade
Cutting Speed
(m/min)
UP20M
120 (80 150)
UTi20T
100 (70 130)
UP20M
80 (60 100)
UTi20T
80 (60 100)
HTi10
100 (70 130)
INSERTS
1.0 1.75
2.0 2.5
3.0 3.5
Geometry
RE
12.7 4.76
0.1 MTTL(60)
12.7 4.76
12.7 4.76
0.2
0.3
IC
RE
IC
a
a
Dimensions (mm)
ISO
Pitch mm
(thread/inch)
60
HTi10
G
G
UTi20T
Carbide
NX2525
Partial Profile 60
MTTL436001
MTTL436002
MTTL436003
UP20M
Order Number
Class
Type
Coated Cermet
DCON
1.5
THREADING
DCON
LF
Stock
OAL
Order Number
Dimensions (mm)
DCON
LF
OAL
Set Bolt
Wrench
Head
B13232
32
260
29
300
SD32
HKY60R
DPT2132R
B14040
40
310
37
360
SD40
HKY60R
DPT2140R
y RANGE OF MACHINING
Range of
Threading
Prepared Hole Diameter D (mm)
Insert : MTTR/L(55)
Thread per Tooth
Thread Pitch P (mm)
Insert : MTTR/L(60)
Range of
Threading
Prepared Hole Diameter D (mm)
SPARE PARTS
P001
G033
THREADING
THREADING METHODS
Right Hand Thread
Left Hand Thread

Holder Reversed
INTERNAL
EXTERNAL
Holder Reversed
INSERT TYPES
THREADING
Partial form
Semi-full form (Trapezoidal threads only)
Full form
a The same insert can be used for a range of pitches.

a Shorter tool life because the corner radius of the
a No deburring needed after threading.

a Requires different threading inserts.
insert is smaller than that of the full form insert.
a No deburring needed after threading.

a Requires different threading inserts.
a Finishing with another operation is necessary.
a Finishing with another operation is necessary.

Crest Radius
(Additional turning necessary to finish the thread crest.)
Crest Radius
(Wiped/finished surface.)
Finished
Surface
Finished
Surface
Pre-finished Surface
Pre-finished Surface
Feed Direction
Insert
Crest Radius
(Additional turning necessary to finish the thread crest.)
FinishedSurface
Pre-finished
Surface
Finishing
allowance
Feed Direction
Insert
Feed Direction
Insert
INFEED METHODS
1 5
Radial Infeed
Features
Advantages
a Easiest to use.
a Relatively easy to use.
(Standard programme for

(Semi-standard program for
threading)
threading.)
a Wide application. (Cutting
a Reduced cutting force.
conditions easy to change.) a Suitable for large pitch
a Uniform wear of the right and
threads or materials that
left sides of the cutting edge.
peel easily.
Modified Flank Infeed
Incremental Infeed
a Preventing flank wear on the

right side of the cutting edge.
a Suitable for large pitch
peel easily.
a Good chip discharge.
a Uniform flank wear of the

right and left sides of the
cutting edge.
a Suitable for large pitch
peel easily.
a Complex machining
programming.
a Difficult to change cutting
depth. (Re-programming
necessary)
a Complex machining
programming.
a Difficult to change cutting
depth. (Re-programming
necessary)
a Difficult chip control.
a Good chip discharge.
Disadvantages
G034
Flank Infeed
a Difficult chip control.

a Subject to vibration in the
later in stages of cutting.

a Ineffective for large pitch
threading.
a Heavy load on the corner
radius.
a Large flank wear on the right

side of the cutting edge.
a Relatively difficult to change
cutting depth.
(Re-programming
necessary)
THREADING DEPTH
Features
Advantages
V1=V2
V1
V2
Disadvantages
a Easy to use.
(Standard programme for threading.)
a Long chips generated during the

final pass.
a Superior resistance to vibration.

(Constant cutting force.)
a Complex calculation of cutting depth

when changing the number of passes.
a Reduced load on corner radius during

the first half of the passes.
a Subject to vibration in the later

stages of cutting.
(Increased cutting force)
Fixed cut area
X1=X2
X1
a Easy chip control.

(Optional setting of chip thickness)
X2
a In some cases, changing the NC

programme is necessary.
THREADING
a Easy to calculate cutting depth when

changing the number of passes.
a Good chip control.
Fixed cutting depth
It is recommended to set the depth of cut of the final pass to 0.05mm 0.025mm.
* Large
cutting depths can cause vibration, leading to a poor surface finish.
a FORMULAE
y Formulae to calculate infeed for each pass in a reduced series.
]apn
]apn :
n
ap
nap
b
:
:
:
:
ap
nap 1
Depth of cut
Actual pass
Total depth of cut
Number of passes
1st pass 0.3
2nd pass 2 1 = 1
3rd pass 3 1 = 2
nth pass n 1
(Example)
External threading (ISO Metric)
Pitch : 1.0mm
ap
: 0.6mm
nap : 5 passes
0.60
1st Pass ]ap1 =
51
0.60
2st Pass ]ap2 =
51
0.60
3st Pass ]ap3 =
51
0.60
4st Pass ]ap4 =
51
0.60
5st Pass ]ap5 =
51
0.3
= 0.16
0.16 (]ap1)
21
= 0.3
0.14 (]ap2 ]ap1)
31
= 0.42
0.12 (]ap3 ]ap2 )
41
= 0.52
0.1 (]ap4 ]ap3)
51
= 0.6
0.08 (]ap5 ]ap4)
a NC PROGRAMME FOR MODIFIED FLANK INFEED

y Example) M121.0 5 passes modified 5
External Threading
G00 Z = 5.0
X = 14.0
G92 U 4.34
G00 W 0.07
G92 U 4.64
G00 W 0.06
G92 U 4.88
G00 W 0.05
G92 U 5.08
G00 W 0.03
G92 U 5.20
G00
Z 13.0 F1.0
Z 13.0 F1.0
Z 13.0 F1.0
Z 13.0 F1.0
Z 13.0 F1.0
Internal Threading
G00 Z = 5.0
X = 10.0
G92 U4.34 Z 13.0 F1.0
G00 W 0.07
G92 U4.64 Z 13.0 F1.0
G00 W 0.05
G92 U4.84 Z 13.0 F1.0
G00 W 0.04
G92 U5.02 Z 13.0 F1.0
G00 W 0.03
G92 U5.14 Z 13.0 F1.0
G00
G035
THREADING
SELECTING CUTTING CONDITIONS
Priority
Tool Life
Threading
Methods
Radial
Flank
(] : Modified)
Cutting
Depth
Fixed Cutting Depth
*
*
Fixed Cut Area
Cutting Force
Surface Finish
Precision of thread
(] : Modified)
Efficiency
(Reduced Passes)
u
u
u
Tool life and surface finish accuracy can be increased by changing the threading method from flank infeed to modified flank infeed.
Chip control can be improved by increasing the cutting depth in the later half of passes.
CUTTING DEPTH AND THE NUMBER OF PASSES

y Selection of the appropriate cutting depth
and the right number of passes is vital for

threading.
THREADING
Chip Discharge
For most threading, use a "threading cycle program,"

which has originally been installed on machines, and
specify "total cutting depth" and "cutting depth in the first
or final pass."
Cutting depth and the number of passes are easy to
change for the radial infeed method, thus making it easy
to determine the appropriate cutting conditions.
FEATURES AND BENEFITS OF MITSUBISHI PRODUCTS

Insert grades with high wear and plastic deformation
resistance, specially produced for threading tools, ensure
highly efficient cutting by enabling high-speed machining
and a reduced number of passes.
Machining Cost
Reduction
ADVICE ON IMPROVED THREADING

y Increasing tool life
To prevent damage to the corner radius Recommended method - Modified flank infeed
To have uniform flank wear on both sides of a cutting edge Recommended method - Radial infeed
To prevent crater wear Recommended method - Flank infeed
y Preventing chip problems

Change to flank or modified infeed.
During radial infeed cutting, use an inverted holder and
change the coolant supply to a downward direction.
When using the radial infeed method, set the minimum
cutting depth at around 0.2mm to make the chips thicker.
y To achieve highly efficient machining

Increase cutting speed. (Dependant on the maximum
revolution and rigidity of the machine.)
Reduce the number of passes. (Reduce by 30-40%.)
A reduced number of passes can improve chip discharge
because of the thicker chips generated.
G036
y Preventing vibration
Change to flank or modified infeed.
When using radial infeed, reduce cutting depth in the later
half of passes and lower the cutting speed.
y Increased surface finish accuracy

A final wiping pass should be performed at the same depth
of cut as the last regular pass.
When using the flank infeed method, change to radial
infeed only during the final pass.
SELECTING A SHIM FOR THE MMT SERIES
Lead Angle (%)
Lead angle (%) depends on a combination of thread diameter and pitch. Select a shim
so that the lead angle of the thread can coincide with the flank angles of the thread and
insert ($1, $2). No need to change a shim for general threading with an MMT holder.
When threading with a small diameter or large pitch, change the shim depending on the
lead angle, referring to the table and graph below. When threading left hand threads,
change to a shim with a negative inclination angle.
Fla
nk
Ang
le (
y SHIM REFERENCE TABLE (THREADING DIAMETER) (Thread angle 60 and 55)
(mm)
0.5
0.75
1
1.25
1.5
1.75
2
2.5
3
3.5
4
4.5
5
Fla
Left Hand Thread (mm)
Right Hand Thread (mm)

Threading
4.5
impossible
< &1.7
&1.7 & 2.3
< &2.5
&2.5 & 3.4
< &3.3
&3.3 & 4.6
< &4.1
&4.1 & 5.7
< &5.0
&5.0 & 6.8
< &5.8
&5.8 & 8.0
< &6.6
&6.6 & 9.1
< &8.3
& 8.3 &11.4
< &9.9
&9.9 & 13.7
< &11.6 &11.6 &15.9
< &13.2 &13.2 & 18.2
< &14.9 &14.9 & 20.5
< &16.5 &16.5 & 22.8
Pitch
$ 2
($1
3.5
2.5
1.5
&2.3 & 3.0

&3.4 & 4.6
&4.6 & 6.1
&5.7 & 7.6
&6.8 & 9.1
& 8.0 &10.6
& 9.1 &12.1
& 11.4 &15.2
& 13.7 &18.2
&15.9 &21.3
& 18.2 &24.3
& 20.5 &27.3
& 22.8 &30.4
& 3.0 & 4.6

& 4.6 & 6.8
& 6.1 & 9.1
& 7.6 & 11.4
& 9.1 & 13.7
&10.6 & 16.0
&12.1 & 18.2
&15.2 & 22.8
&18.2 & 27.3
&21.3 & 31.9
&24.3 & 36.5
&27.3 & 41.0
&30.4 & 45.6
& 4.6 & 9.1

&6. 8 & 13.7
& 9.1 & 18.2
& 11.4 & 22.8
& 13.7 & 27.4
& 16.0 & 31.9
& 18.2 & 36.5
& 22.8 & 45.6
& 27.3 & 54.7
& 31.9 & 63.8
& 36.5 & 72.9
& 41.0 & 82.1
& 45.6 & 91.2
0.5
> & 9.1
> & 13.7
> & 18.2
> & 22.8
> & 27.4
> & 31.9
> & 36.5
> & 45.6
> & 54.7
> & 63.8
> & 72.9
> & 82.1
> & 91.2
Threading
impossible
< & 3.6
< & 5.5
< & 7.3
< & 9.1
< & 10.9
< & 12.8
< & 14.6
< & 18.2
< & 21.9
< & 25.5
< & 29.2
< & 32.8
< & 36.5
1 .5
& 3.6 & 9.1
&5. 5 & 13.7
& 7.3 & 18.2
& 9.1 & 22.8
& 10.9 & 27.4
& 12.8 & 31.9
& 14.6 & 36.5
& 18.2 & 45.6
& 21.9 & 54.7
& 25.5 & 63.8
& 29.2 & 72.9
& 32.8 & 82.1
& 36.5 & 91.2
0 .5
> &9.1
> &13.7
> &18.2
> &22.8
> &27.4
> &31.9
> &36.5
> &45.6
> &54.7
> &63.8
> &72.9
> &82.1
> &91.2
(Note) Back turning in the case of left hand threads.
THREADING
Lead
Angle
gle
n
kA
Inclination Angle (')
y FLANK ANGLE AND LEAD ANGLE
y SHIM REFERENCE GRAPH (Thread angle 60 and 55)

Right Hand Thread
Left Hand Thread
%=1.5 (Standard Shim)
%=0.5
Threading Pitch (mm)
% : Lead Angle
Threading Pitch (thread/inch)
Threading
impossible
% : Lead Angle
%=2.5
%=4.5 %=3.5
%= 1.5
Threading
impossible
%= 0.5
Threading Diameter (mm)
(Note) When a thread lead angle < the tool flank angle, change the shim to prevent side interference with the insert.
(Refer to the table below for the calculation of thread lead angle and tool flank angle.)
y SHIM REFERENCE TABLE (THREADING DIAMETER) (Thread angle 30 and 29)

Lead
Angle
Pitch
(mm)
0.5
0.75
1
1.25
1.5
1.75
2
2.5
3
3.5
4
4.5
5
Left Hand Thread (mm)
Right Hand Thread (mm)

Threading
impossible
< &1.8
< &2.7
< &3.6
< &4.5
< &5.5
< &6.4
< &7.3
< &9.1
< &10.9
< &12.7
< &14.6
< &16.4
< &18.2
4.5
3.5
2.5
1.5
&1.8 & 2.3

&2.7 & 3.4
&3.6 & 4.6
&4.5 & 5.7
&5.5 & 6.8
&6.4 & 8.0
&7.3 & 9.1
& 9.1 &11.4
&10.9 &13.7
&12.7 & 15.9
&14.6 & 18.2
&16.4 & 20.5
&18.2 & 22.8
&2.3 & 3.0

&3.4 & 4.6
&4.6 & 6.1
&5.7 & 7.6
&6.8 & 9.1
& 8.0 &10.6
& 9.1 &12.1
& 11.4 &15.2
&13.7 &18.2
& 15.9 &21.3
& 18.2 &24.3
& 20.5 &27.3
& 22.8 &30.4
& 3.0 & 4.6

& 4.6 & 6.8
& 6.1 & 9.1
& 7.6 & 11.4
& 9.1 & 13.7
&10.6 & 16.0
&12.1 & 18.2
&15.2 & 22.8
&18.2 & 27.3
&21.3 & 31.9
&24.3 & 36.5
&27.3 & 41.0
&30.4 & 45.6
& 4.6 & 9.1

&6. 8 & 13.7
& 9.1 & 18.2
& 11.4 & 22.8
& 13.7 & 27.4
& 16.0 & 31.9
& 18.2 & 36.5
& 22.8 & 45.6
& 27.3 & 54.7
& 31.9 & 63.8
& 36.5 & 72.9
& 41.0 & 82.1
& 45.6 & 91.2
0.5
> & 9.1
> & 13.7
> & 18.2
> & 22.8
> & 27.4
> & 31.9
> & 36.5
> & 45.6
> & 54.7
> & 63.8
> & 72.9
> & 82.1
> & 91.2
Threading
impossible
< & 4.6
< & 6.8
< & 9.1
< & 11.4
< & 13.7
< & 16.0
< & 18.2
< & 22.8
< & 27.3
< & 31.9
< & 36.5
< & 41.0
< & 45.6
1 .5
& 4.6 & 9.1
&6. 8 & 13.7
& 9.1 & 18.2
& 11.4 & 22.8
& 13.7 & 27.4
& 16.0 & 31.9
& 18.2 & 36.5
& 22.8 & 45.6
& 27.3 & 54.7
& 31.9 & 63.8
& 36.5 & 72.9
& 41.0 & 82.1
& 45.6 & 91.2
0 .5
> &9.1
> &13.7
> &18.2
> &22.8
> &27.4
> &31.9
> &36.5
> &45.6
> &54.7
> &63.8
> &72.9
> &82.1
> &91.2
G037
THREADING
y SHIM REFERENCE GRAPH (Thread angle 30 and 29)

Right Hand Thread
Left Hand Thread
%=0.5
%=1.5 (Standard Shim)
% : Lead Angle
Threading
impossible
% : Lead Angle
%=2.5
%=4.5 %=3.5
%= 1.5
Threading
impossible
%= 0.5
(Note) When a thread lead angle < the tool flank angle, change the shim to prevent side interference with the insert.
(Refer to the table below for the calculation of thread lead angle and tool flank angle.)
THREADING
y Selection table
Lead
Angle
Opening angle 60/55

Right Hand Thread
Opening angle 60/55

Left Hand Thread
Opening angle 30/29

Right Hand Thread
Opening angle 30/29

Left Hand Thread
P05
P05
N05
N05
P05
P05
N05
N05
0.5
P05
P05
N05
N05
P05
P05
N05
N05
P15
P15
N15
N15
P15
P15
N15
N15
1.5
P15
P15
N15
N15
P15
P15
N15
N15
P25
P25
N15
N15
P25
P25
Compatible
Compatible
2.5
P25
P25
Compatible
Compatible
P25
P25
Compatible
Compatible
P35
P35
Compatible
Compatible
P35
P35
Compatible
Compatible
3.5
P35
P35
Compatible
Compatible
P35
P35
Compatible
Compatible
P45
P45
Compatible
Compatible
P45
P45
Compatible
Compatible
4.5
P45
P45
Compatible
Compatible
P45
P45
Compatible
Compatible
P45
P45
Compatible
Compatible
Compatible
Compatible
Compatible
Compatible
Compatible
Compatible
Compatible
Compatible
Compatible
Compatible
Compatible
Compatible
5.5
When replacing a shim, check if the difference between the

thread lead angle and shim inclination angle is within:
2.5 0.5 where thread helix angle is 60 (55)
2 1 where thread helix angle is 30 (29)
Inclination angle of a standard shim is 0.
The holder has a 1.5 lead angle.
*
*
y EXAMPLE OF SELECTING A SHIM
y CALCULATION OF THREAD LEAD ANGLE

% : Lead angle
tan%
nP
I
=
=
)d
)d
I : Lead
n : Number of threads
P : Pitch
d : Effective diameter of thread
y RELIEF ANGLE OF AN INSERT SET ON A HOLDER
When the thread lead angle is 2.2

Thread Helix Angle Internal Relief Angle External Relief Angle
zIn the case when the thread helix angle is 60
60
8.8
5.8
(2.2 lead angle) (2.50.5) = -0.31.7 shim inclination angle is appropriate.
55
7.9
5.2
Threading with a standard shim (0 inclination angle) is possible. But, replacing with a shim with
30
4.1
2.7
a 1 inclination angle is recommended, refer to Standard Shim List on pages G012 and G013.
29
4
2.6
xIn the case when the thread helix angle is 30
(2.2 lead angle) (2 1) = -0.2 1.2 shim inclination angle is appropriate.
Replacing with a shim with a 1 inclination angle is recommended, referring to
Standard Shim List on pages G012 and G013.
Refer to the web catalogue.

* http://www.mitsubishicarbide.net/mmc/jp/formula.html
G038
Relief angles ($2, $1) of an insert become small when

the thread helix angle of a trapezoidal, round, or other
thread is small. Take care when selecting a shim.
STANDARD OF DEPTH OF CUT EXTERNAL (RADIAL INFEED)

y ISO Metric
Pitch Total
(mm) Cutting
Depth
0.5
0.31
0.75 0.46
1.0
0.61
1.25 0.77
1.5
0.92
1.75 1.07
2.0
1.23
2.5
1.53
3.0
1.84
3.5
2.15
4.0
2.45
4.5
2.76
5.0
3.07
Number of Passes
1
0.10
0.16
0.18
0.19
0.22
0.22
0.24
0.26
0.27
0.33
0.34
0.38
0.42
0.08
0.14
0.15
0.17
0.21
0.21
0.23
0.23
0.25
0.30
0.31
0.34
0.38
0.07
0.10
0.12
0.14
0.17
0.16
0.17
0.19
0.20
0.24
0.24
0.28
0.32
0.06
0.06
0.10
0.11
0.14
0.13
0.16
0.17
0.18
0.21
0.22
0.24
0.27
0.06
0.10
0.12
0.11
0.14
0.15
0.16
0.18
0.19
0.22
0.24
0.06
0.06
0.09
0.12
0.13
0.14
0.17
0.17
0.20
0.22
0.09
0.11
0.12
0.13
0.15
0.16
0.18
0.20
0.06
0.06
0.11
0.12
0.14
0.14
0.16
0.18
0.11
0.12
0.14
0.14
0.16
0.18
Insert Type
10
0.06
0.11
0.12
0.13
0.15
0.17
11
0.10
0.11
0.12
0.14
0.16
12
13
14
0.06
0.06
0.12 0.11 0.06
0.13 0.12 0.06
0.15 0.12 0.06
G-class ground inserts

3-D chip breakers
MMT16ER050ISO
MMT16ER075ISO
MMT16ER100ISO
MMT16ER125ISO
MMT16ER150ISO
MMT16ER175ISO
MMT16ER200ISO
MMT16ER250ISO
MMT16ER300ISO
MMT22ER350ISO
MMT22ER400ISO
MMT22ER450ISO
MMT22ER500ISO
MMT16ER100ISO-S
MMT16ER125ISO-S
MMT16ER150ISO-S
MMT16ER175ISO-S
MMT16ER200ISO-S
MMT16ER250ISO-S
MMT16ER300ISO-S
y American UN
Number of Passes
1
0.17
0.17
0.18
0.20
0.22
0.22
0.23
0.25
0.28
0.28
0.28
0.34
0.35
0.37
0.42
0.43
0.15
0.14
0.16
0.18
0.20
0.20
0.21
0.22
0.23
0.23
0.24
0.29
0.30
0.33
0.35
0.39
0.11
0.10
0.14
0.13
0.15
0.15
0.16
0.17
0.18
0.19
0.19
0.22
0.24
0.28
0.29
0.31
0.06
0.09
0.11
0.11
0.13
0.12
0.13
0.14
0.16
0.16
0.16
0.17
0.19
0.24
0.25
0.27
0.06
0.06
0.10
0.11
0.11
0.11
0.13
0.14
0.14
0.14
0.15
0.16
0.20
0.21
0.24
0.06
0.06
0.11
0.11
0.12
0.13
0.13
0.13
0.14
0.15
0.17
0.18
0.22
0.06
0.10
0.11
0.12
0.12
0.13
0.13
0.14
0.16
0.17
0.20
0.06
0.06
0.06
0.11
0.12
0.12
0.13
0.15
0.16
0.19
0.06
0.11
0.11
0.12
0.14
0.15
0.19
Insert Type
10
0.06
0.06
0.11
0.12
0.13
0.18
11
12
13
14
0.06
0.06
0.12 0.11 0.06
0.17 0.15 0.12 0.06

3-D chip breakers
MMT16ER320UN
MMT16ER280UN
MMT16ER240UN
MMT16ER200UN
MMT16ER180UN
MMT16ER160UN
MMT16ER140UN
MMT16ER130UN
MMT16ER120UN
MMT16ER110UN
MMT16ER100UN
MMT16ER090UN
MMT16ER080UN
MMT22ER070UN
MMT22ER060UN
MMT22ER050UN
MMT16ER160UN-S
MMT16ER140UN-S
MMT16ER120UN-S
THREADING
Pitch Total
(thread/ Cutting
inch) Depth
32 0.49
28 0.56
24 0.65
20 0.78
18 0.87
16 0.97
14 1.11
13 1.20
12 1.30
11 1.42
10 1.56
9 1.73
8 1.95
7 2.22
6 2.60
5 3.12
y Whitworth for BSW, BSP

Pitch Total
(thread/ Cutting
inch) Depth
28 0.58
26 0.63
20 0.81
19 0.86
18 0.90
16 1.02
14 1.16
12 1.36
11 1.48
10 1.63
9 1.81
8 2.03
7 2.32
6 2.71
5 3.25
Number of Passes
1
0.17
0.18
0.20
0.21
0.25
0.21
0.23
0.27
0.27
0.27
0.28
0.30
0.34
0.35
0.42
0.14
0.15
0.18
0.19
0.19
0.18
0.21
0.25
0.24
0.25
0.26
0.27
0.32
0.33
0.40
0.11
0.13
0.14
0.15
0.15
0.15
0.17
0.20
0.20
0.20
0.21
0.22
0.26
0.27
0.35
0.10
0.11
0.12
0.13
0.13
0.13
0.14
0.16
0.17
0.17
0.18
0.19
0.22
0.23
0.29
0.06
0.06
0.11
0.12
0.12
0.11
0.12
0.15
0.15
0.15
0.16
0.17
0.20
0.21
0.26
0.06
0.06
0.06
0.09
0.12
0.14
0.14
0.15
0.15
0.16
0.18
0.20
0.24
0.09
0.11
0.13
0.13
0.13
0.14
0.15
0.17
0.19
0.22
0.06
0.06
0.06
0.12
0.13
0.13
0.14
0.16
0.17
0.20
0.06
0.12
0.12
0.13
0.15
0.16
0.19
Insert Type
10
0.06
0.12
0.12
0.14
0.15
0.18
11
0.06
0.12
0.12
0.14
0.17
12
13
14
0.06
0.06
0.13 0.12 0.06
0.15 0.12 0.06

3-D chip breakers
MMT16ER280W
MMT16ER260W
MMT16ER200W
MMT16ER190W
MMT16ER180W
MMT16ER160W
MMT16ER140W
MMT16ER120W
MMT16ER110W
MMT16ER100W
MMT16ER090W
MMT16ER080W
MMT22ER070W
MMT22ER060W
MMT22ER050W
MMT16ER190W-S
MMT16ER140W-S
MMT16ER110W-S
y BSPT
Pitch Total
(thread/ Cutting
inch) Depth
28 0.58
19 0.86
14 1.16
11 1.48
Number of Passes
1
0.17
0.22
0.24
0.25
0.14
0.19
0.20
0.23
0.11
0.15
0.17
0.21
0.10
0.12
0.14
0.18
0.06
0.12 0.06
0.12 0.12 0.11 0.06
0.16 0.14 0.13 0.12 0.06
Insert Type

3-D chip breakers
MMT16ER280BSPT
MMT16ER190BSPT MMT16ER190BSPT-S
(Note) Set the finishing allowance on a diameter at approx. 0.1mm when using a full form insert.
Please note the cutting depth and the number of passes when a corner radius of a partial form insert or of an internal threading
insert is small to prevent damage to the insert corner.
Please set the cutting depth sufficiently deep enough on materials such as hardened steel or austenitic stainless steel to help
prevent premature wear and chipping caused by the outer layer of the material.
G039
THREADING
STANDARD OF DEPTH OF CUT EXTERNAL (RADIAL INFEED)
y Round DIN 405
Pitch
(thread/
inch)
10
8
6
4
Total
Cutting
Depth
1.27
1.59
2.12
3.18
Number of Passes
1
0.23
0.23
0.26
0.34
2
0.21
0.21
0.25
0.33
3
0.20
0.20
0.24
0.32
4
0.19
0.19
0.22
0.30
5
0.16
0.18
0.21
0.28
6
0.12
0.16
0.19
0.26
3
0.16
0.21
0.24
0.24
0.26
4
0.13
0.17
0.19
0.22
0.24
5
0.11
0.14
0.18
0.21
0.22
6
0.06
0.12
0.17
0.17
0.21
7
0.10
0.14
0.17
0.24
8
0.06
0.12
0.16
0.22
10
11
12
13
0.10
0.14
0.20
0.06
0.12
0.19
0.10
0.17
0.06
0.15
0.12
0.06
10
11
12
13
14
Insert Type
14
MMT16ER100RD
MMT16ER080RD
MMT16ER060RD
MMT22ER040RD
y ISO Trapezoidal 30
Pitch Total
Cutting
(mm) Depth
1.5 0.90
2.0 1.25
3.0 1.75
4.0 2.25
5.0 2.75
Number of Passes
1
0.23
0.29
0.32
0.33
0.35
2
0.21
0.26
0.31
0.32
0.32
7
0.06
0.15
0.16
0.19
8
0.13
0.15
0.19
9
0.06
0.14
0.17
0.13
0.15
0.12
0.14
0.06
0.13
0.12
0.06
10
11
12
13
14
Insert Type
MMT16ER150TR
MMT16ER200TR
MMT16ER300TR
MMT22ER400TR
MMT22ER500TR
THREADING
y American ACME
Pitch
(thread/
inch)
12
10
8
6
5
Total
Cutting
Depth
1.19
1.52
1.84
2.37
2.79
Number of Passes
1
0.27
0.29
0.30
0.34
0.36
2
0.23
0.25
0.26
0.30
0.33
3
0.20
0.21
0.22
0.27
0.30
4
0.17
0.18
0.19
0.24
0.26
5
0.14
0.16
0.16
0.21
0.23
6
0.12
0.14
0.15
0.19
0.20
1
0.16
0.16
0.17
0.19
0.23
0.26
0.26
0.28
0.30
0.31
2
0.14
0.12
0.14
0.16
0.18
0.21
0.23
0.27
0.29
0.30
3
0.10
0.09
0.14
0.13
0.14
0.14
0.17
0.20
0.21
0.23
4
0.06
0.09
0.10
0.10
0.10
0.12
0.12
0.17
0.15
0.18
0.06
0.06
0.09
0.10
0.10
0.11
0.13
0.13
0.15
0.06
0.06
0.09
0.10
0.11
0.12
0.14
4
0.15
5
0.13
6
0.12
7
0.06
0.12
0.14
0.16
0.18
0.11
0.13
0.14
0.17
0.06
0.12
0.12
0.16
0.11
0.12
0.15
0.06
0.11
0.14
10
11
0.11
0.13
0.06
0.12
Insert Type
MMT16ER120ACME
MMT16ER100ACME
MMT16ER080ACME
MMT22ER060ACME
MMT22ER050ACME
0.06
y UNJ
Pitch
(thread/
inch)
32
28
24
20
18
16
14
12
10
8
Total
Cutting
Depth
0.46
0.52
0.61
0.73
0.81
0.92
1.05
1.22
1.47
1.83
Number of Passes
7
0.06
0.06
0.11
0.13
0.10
0.12
0.06
0.11
Insert Type
MMT16ER320UNJ
MMT16ER280UNJ
MMT16ER240UNJ
MMT16ER200UNJ
MMT16ER180UNJ
MMT16ER160UNJ
MMT16ER140UNJ
MMT16ER120UNJ
MMT16ER100UNJ
MMT16ER080UNJ
0.10
0.06
10
0.10
11
0.06
10
0.06
0.13
11
12
0.11
0.06
10
11
12
y API Buttress Casing

Pitch
(thread/
inch)
5
Total
Cutting
Depth
1
1.55 0.25
Number of Passes
2
0.23
3
0.17
7
0.12
8
0.11
9
0.11
Insert Type
MMT22ER050APBU
y API Round Casing&Tubing

Pitch
(thread/
inch)
10
8
Total
Cutting
Depth
1
1.41 0.25
1.81 0.25
Number of Passes
2
0.23
0.24
3
0.16
0.19
4
0.14
0.16
5
0.12
0.14
6
0.12
0.14
7
0.12
0.13
8
0.11
0.13
9
0.10
0.13
Insert Type
MMT16ER100APRD
MMT16ER080APRD
y American NPT
Pitch
(thread/
inch)
27
18
14
11.5
8
Total
Cutting
Depth
0.66
1.01
1.33
1.64
2.42
Number of Passes
1
0.15
0.20
0.23
0.24
0.33
2
0.13
0.16
0.19
0.19
0.28
3
0.12
0.14
0.16
0.17
0.23
4
0.11
0.13
0.14
0.15
0.20
5
0.09
0.12
0.13
0.15
0.18
6
0.06
0.11
0.12
0.13
0.16
3
0.11
0.14
0.16
0.19
0.23
4
0.09
0.13
0.14
0.15
0.19
5
0.08
0.12
0.13
0.13
0.17
6
0.06
0.11
0.12
0.11
0.16
0.09
0.11
0.13
0.15
0.06
0.10
0.12
0.14
9
0.09
0.11
0.13
13
14
15
0.06
0.10
0.12
0.09
0.12
0.06
0.11
0.11
0.10
0.06
10
11
12
13
14
15
Insert Type
MMT16ER270NPT
MMT16ER180NPT
MMT16ER140NPT
MMT16ER115NPT
MMT16ER080NPT
y American NPTF
Pitch
(thread/
inch)
27
18
14
11.5
8
G040
Total
Cutting
Depth
0.64
1.00
1.35
1.63
2.38
Number of Passes
1
0.16
0.19
0.23
0.24
0.32
2
0.14
0.16
0.21
0.23
0.27
0.09
0.11
0.11
0.15
0.06
0.10
0.11
0.14
9
0.09
0.10
0.13
0.06
0.10
0.12
0.10
0.12
0.06
0.11
0.11
0.10
0.06
Insert Type
MMT16ER270NPTF
MMT16ER180NPTF
MMT16ER140NPTF
MMT16ER115NPTF
MMT16ER080NPTF
STANDARD OF DEPTH OF CUT INTERNAL (RADIAL INFEED)

y ISO Metric
Total
Pitch Cutting
(mm) Depth
0.5
0.75
1.0
1.25
1.5
1.75
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0.29
0.43
0.58
0.72
0.87
1.01
1.15
1.44
1.73
2.02
2.31
2.60
2.89
Number of Passes
1
0.09
0.15
0.17
0.18
0.21
0.21
0.24
0.25
0.26
0.32
0.33
0.36
0.41
0.07
0.13
0.15
0.16
0.20
0.20
0.22
0.24
0.25
0.30
0.31
0.33
0.38
0.07
0.09
0.11
0.12
0.16
0.15
0.18
0.21
0.22
0.23
0.24
0.28
0.32
0.06
0.06
0.09
0.11
0.13
0.12
0.14
0.15
0.17
0.19
0.22
0.24
0.27
0.06
0.09
0.11
0.10
0.12
0.13
0.14
0.17
0.18
0.21
0.24
0.06
0.06
0.09
0.10
0.12
0.13
0.15
0.15
0.19
0.21
0.08
0.09
0.10
0.12
0.14
0.14
0.16
0.18
0.06
0.06
0.09
0.11
0.13
0.13
0.15
0.16
0.09
0.10
0.12
0.12
0.14
0.15
Insert Type
10
0.06
0.09
0.11
0.12
0.13
0.14
11
0.08
0.10
0.11
0.12
0.13
12
13
14
MMT11IR050ISO
MMT11IR075ISO
MMT11IR100ISO
MMT11IR125ISO
MMT11IR150ISO
MMT11IR175ISO
MMT11IR200ISO
0.06
0.06
0.10 0.10 0.06
0.12 0.11 0.06
0.12 0.12 0.06

3-D chip breakers
MMT16IR050ISO
MMT16IR075ISO
MMT16IR100ISO MMT11IR100ISO-S MMT16IR100ISO-S

MMT16IR175ISO
MMT16IR175ISO-S
MMT16IR200ISO
MMT16IR200ISO-S
MMT16IR250ISO
MMT16IR250ISO-S
MMT16IR300ISO
MMT16IR300ISO-S
MMT22IR350ISO
MMT22IR400ISO
MMT22IR450ISO
MMT22IR500ISO
y American UN
32
28
24
20
18
16
14
13
12
11
10
9
8
7
6
5
0.46
0.52
0.61
0.73
0.81
0.92
1.05
1.13
1.22
1.33
1.47
1.63
1.83
2.09
2.44
2.93
Number of Passes
1
0.16
0.16
0.17
0.18
0.20
0.20
0.21
0.22
0.24
0.24
0.25
0.31
0.31
0.36
0.40
0.41
0.14
0.13
0.15
0.15
0.18
0.18
0.18
0.19
0.22
0.22
0.22
0.23
0.26
0.30
0.33
0.35
0.10
0.09
0.13
0.13
0.14
0.15
0.15
0.16
0.18
0.20
0.21
0.21
0.21
0.24
0.25
0.31
0.06
0.08
0.10
0.11
0.12
0.12
0.13
0.14
0.16
0.15
0.14
0.17
0.18
0.21
0.23
0.26
0.06
0.06
0.10
0.11
0.11
0.11
0.13
0.13
0.12
0.13
0.15
0.16
0.18
0.19
0.23
0.06
0.06
0.10
0.11
0.12
0.12
0.12
0.12
0.14
0.15
0.17
0.17
0.21
0.06
0.10
0.11
0.11
0.11
0.12
0.13
0.14
0.16
0.16
0.20
0.06
0.06
0.06
0.11
0.11
0.12
0.13
0.15
0.15
0.19
0.06
0.11
0.11
0.12
0.14
0.14
0.17
Insert Type
10
0.06
0.06
0.11
0.12
0.13
0.15
11
12
13
14
0.06
0.06
0.12 0.11 0.06
0.14 0.13 0.12 0.06
MMT11IR320UN
MMT11IR280UN
MMT11IR240UN
MMT11IR200UN
MMT11IR180UN
MMT11IR160UN
MMT11IR140UN
MMT16IR320UN
MMT16IR280UN
MMT16IR240UN
MMT16IR200UN
MMT16IR180UN
MMT16IR160UN
MMT16IR140UN
MMT16IR130UN
MMT16IR120UN
MMT16IR110UN
MMT16IR100UN
MMT16IR090UN
MMT16IR080UN
MMT22IR070UN
MMT22IR060UN
MMT22IR050UN

3-D chip breakers
MMT16IR160UN-S
MMT16IR140UN-S
MMT16IR120UN-S
THREADING
Pitch Total
(thread/ Cutting
inch) Depth
y Whitworth for BSW, BSP

Pitch Total
(thread/ Cutting
inch) Depth
28
26
20
19
18
16
14
12
11
10
9
8
7
6
5
0.58
0.63
0.81
0.86
0.90
1.02
1.16
1.36
1.48
1.63
1.81
2.03
2.32
2.71
3.25
Number of Passes
1
0.17
0.18
0.20
0.21
0.25
0.21
0.23
0.27
0.27
0.27
0.28
0.30
0.34
0.35
0.42
0.14
0.15
0.18
0.19
0.19
0.18
0.21
0.25
0.24
0.25
0.26
0.27
0.32
0.33
0.40
0.11
0.13
0.14
0.15
0.15
0.15
0.17
0.20
0.20
0.20
0.21
0.22
0.26
0.27
0.35
0.10
0.11
0.12
0.13
0.13
0.13
0.14
0.16
0.17
0.17
0.18
0.19
0.22
0.23
0.29
0.06
0.06
0.11
0.12
0.12
0.11
0.12
0.15
0.15
0.15
0.16
0.17
0.20
0.21
0.26
0.06
0.06
0.06
0.09
0.12
0.14
0.14
0.15
0.15
0.16
0.18
0.20
0.24
0.09
0.11
0.13
0.13
0.13
0.14
0.15
0.17
0.19
0.22
0.06
0.06
0.06
0.12
0.13
0.13
0.14
0.16
0.17
0.20
0.06
0.12
0.12
0.13
0.15
0.16
0.19
Insert Type
10
0.06
0.12
0.12
0.14
0.15
0.18
11
0.06
0.12
0.12
0.14
0.17
12
0.06
0.06
0.13
0.15
13
14
MMT11IR190W
MMT11IR140W
0.12 0.06
0.12 0.06
MMT16IR280W
MMT16IR260W
MMT16IR200W
MMT16IR190W
MMT16IR180W
MMT16IR160W
MMT16IR140W
MMT16IR120W
MMT16IR110W
MMT16IR100W
MMT16IR090W
MMT16IR080W
MMT22IR070W
MMT22IR060W
MMT22IR050W

3-D chip breakers
MMT16IR190W-S
MMT16IR140W-S
MMT16IR120W-S
G041
THREADING
STANDARD OF DEPTH OF CUT INTERNAL (RADIAL INFEED)
y BSPT
Pitch
(thread/
inch)
19
14
11
Total
Cutting
Depth
Number of Passes
1
Insert Type
0.86 0.22 0.19 0.15 0.12 0.12 0.06

1.16 0.24 0.20 0.17 0.14 0.12 0.12 0.11 0.06
1.48 0.25 0.23 0.21 0.18 0.16 0.14 0.13 0.12 0.06

3-D chip breakers
MMT11IR190BSPT MMT16IR190BSPT MMT16IR190BSPT-S

MMT11IR140BSPT MMT16IR140BSPT MMT16IR140BSPT-S
MMT16IR110BSPT MMT16IR110BSPT-S
y Round DIN 405

Pitch Total
(thread/ Cutting
inch) Depth
10
8
6
4
1.27
1.59
2.12
3.18
Number of Passes
1
0.23
0.23
0.26
0.34
0.21
0.21
0.25
0.33
0.20
0.20
0.24
0.32
0.19
0.19
0.22
0.30
0.16
0.18
0.21
0.28
0.12
0.16
0.19
0.26
0.10
0.14
0.17
0.24
10
11
12
13
Insert Type
14
0.06
0.12 0.10 0.06
0.16 0.14 0.12 0.10 0.06
0.22 0.20 0.19 0.17 0.15 0.12 0.06
MMT16IR100RD
MMT16IR080RD
MMT16IR060RD
MMT22IR040RD
y ISO Trapezoidal 30
THREADING
Pitch Total
Cutting
(mm) Depth
1.5
2
3
4
5
0.90
1.25
1.75
2.25
2.75
Number of Passes
1
0.23
0.29
0.32
0.33
0.35
0.21
0.26
0.31
0.32
0.32
0.16
0.21
0.24
0.24
0.26
0.13
0.17
0.19
0.22
0.24
0.11
0.14
0.18
0.21
0.22
0.06
0.12
0.17
0.17
0.21
10
11
12
13
Insert Type
14
MMT16IR150TR
MMT16IR200TR
MMT16IR300TR
MMT22IR400TR
MMT22IR500TR
0.06
0.15 0.13 0.06
0.16 0.15 0.14 0.13 0.12 0.06
0.19 0.19 0.17 0.15 0.14 0.13 0.12 0.06
y American ACME
Pitch Total
(thread/ Cutting
inch) Depth
12
10
8
6
5
1.19
1.52
1.84
2.37
2.79
Number of Passes
1
0.27
0.29
0.30
0.34
0.36
0.23
0.25
0.26
0.30
0.33
0.20
0.21
0.22
0.27
0.30
0.17
0.18
0.19
0.24
0.26
0.14
0.16
0.16
0.21
0.23
0.12
0.14
0.15
0.19
0.20
0.06
0.12
0.14
0.16
0.18
0.11
0.13
0.14
0.17
10
11
12
13
Insert Type
14
MMT16IR120ACME
MMT16IR100ACME
MMT16IR080ACME
MMT22IR060ACME
MMT22IR050ACME
0.06
0.12 0.11 0.06
0.12 0.12 0.11 0.11 0.06
0.16 0.15 0.14 0.13 0.12 0.06
y API Buttress Casing

Pitch Total
(thread/ Cutting
inch) Depth
5
Number of Passes
1
10
Insert Type
11
1.55 0.25 0.23 0.17 0.15 0.13 0.12 0.12 0.11 0.11 0.10 0.06
MMT22IR050APBU
y API Round Casing&Tubing

Pitch Total
(thread/ Cutting
inch) Depth
10
8
Number of Passes
1
10
11
Insert Type
12
1.41 0.25 0.23 0.16 0.14 0.12 0.12 0.12 0.11 0.10 0.06
1.81 0.25 0.24 0.19 0.16 0.14 0.14 0.13 0.13 0.13 0.13 0.11 0.06
MMT16IR100APRD
MMT16IR080APRD
y American NPT
Pitch Total
(thread/ Cutting
inch) Depth
27
18
14
11.5
8
0.66
1.01
1.33
1.64
2.42
Number of Passes
1
0.15
0.20
0.23
0.24
0.33
0.13
0.16
0.19
0.19
0.28
0.12
0.14
0.16
0.17
0.23
0.11
0.13
0.14
0.15
0.20
0.09
0.12
0.13
0.15
0.18
0.06
0.11
0.12
0.13
0.16
0.09
0.11
0.13
0.15
10
11
12
13
14
15
0.06
0.10 0.09 0.06
0.12 0.11 0.10 0.09 0.06
0.14 0.13 0.12 0.12 0.11 0.11 0.10 0.06
Insert Type
MMT16IR270NPT
MMT16IR180NPT
MMT16IR140NPT
MMT16IR115NPT
MMT16IR080NPT
y American NPTF
Pitch Total
(thread/ Cutting
inch) Depth
14
11.5
8
G042
Number of Passes
1
10
11
12
13
14
15
1.35 0.23 0.21 0.16 0.14 0.13 0.12 0.11 0.10 0.09 0.06
1.63 0.24 0.23 0.19 0.15 0.13 0.11 0.11 0.11 0.10 0.10 0.10 0.06
2.38 0.32 0.27 0.23 0.19 0.17 0.16 0.15 0.14 0.13 0.12 0.12 0.11 0.11 0.10 0.06
Insert Type
MMT16IR140NPTF
MMT16IR115NPTF
MMT16IR080NPTF
TROUBLE SHOOTING
Problems
Low thread precision.
Poor surface finish.
Observation
Causes
Solutions
Threads do not mesh

with each other.
Incorrect tool installation.
Shallow thread.
Incorrect depth of cut.
Modify the depth of cut.
Lack of insert wear or plastic

deformation resistance.
Refer to "Quickly generated flank wear." and "Large

plastic deformation." below.
Chips wrap around or clog the work

pieces.
Change to flank infeed and control the chip

discharge direction.
Surface damage.
Set the insert center height at 0mm.

Check holder inclination (Lateral).
Change to an M-class insert with a 3-D chip breaker.
Surface tears.
The side of the insert cutting edge

interferes with the workpiece.
Check the lead angle and select an appropriate shim.
Built-up edge (Welding).
Increase cutting speed.
Surface vibrations.
Short tool life.
Flank wear quickly

generated.
Cutting resistance too high.
Decrease depth of cut per pass.
Cutting speed too high.
Decrease the cutting speed.
Insufficient work piece or tool

clamping.
Re-check work piece and tool clamping.

(Chuck pressure, clamping allowance)
Incorrect tool installation.
Set the insert center height at 0mm.
Cutting speed too high.
Too many passes causes abrasive wear.
Reduce the number of passes.
Small depth of cut for the finishing

pass.
Do not re-cut at 0mm depth of cut, larger than

0.05mm depth of cut is recommended.
Non-uniform wear
of the right and
left sides of the
cutting edge.
The work piece lead angle and the

tool lead angle do not match.
Check the work piece lead angle and select an

appropriate shim.
Chipping and
fracture.
Cutting speed too low.
Increase the number of passes and decrease the

cutting resistance per pass.
Unstable clamping.
Check work piece deflection.
THREADING
Increase coolant pressure and volume.
Shorten tool overhang.

Recheck work piece and tool clamping. (Chuck
pressure, clamping allowance)
Chip packing.
Increase coolant pressure to blow away chips.

Change the tool pass to control chips. (Lengthen
each pass to allow the coolant to clear the chips.
Change from standard internal cutting to back
turning to prevent chip jamming.
Large plastic
deformation.
Non-chamfered work pieces causes

high resistance at the start of each pass.
Chamfer the workpiece entry and exit faces.
High cutting speed and large heat

generation.
Lack of coolant supply.
Check coolant is supply is sufficient.
Increase the number of passes and decrease the

cutting resistance per pass.
Increase coolant pressure and volume.
G043

OF HSK-T TOOLS
zOrganized by application. (Refer to the index on the next page.)
FIGURE SHOWING
THE TOOLING APPLICATION
uses illustrations and arrows to depict
available machining applications along
with cutting edge lead angles.
PRODUCT TYPE
GEOMETRY
TITLE OF PRODUCT SERIES
CHIP BREAKER BY
CUTTING APPLICATION
PRODUCT SECTION
HSK-T TOOLS
FOR MULTI-TASK MACHINES
PCLN
Finish
External turning Facing
FH
Light
Medium
LP
(12)
Medium
MP
(12)
(12)
Medium
Medium Rough
Standard
MK
PCMN
Finish
(12)
(12)
(12)
Stainless
CBN
(12)
Medium Rough
RP
(12)
Dimensions
Insert Number
a a
(12)
(12)
(12)
*1
*2
WT
Dimensions
Order Number
(kg)
CNMo
CNGo 1204oo 65 45 1.3
NP-CNoA
Shim
Shim Pin
LLSCN42
LLP14

LLCL14
Stock
Insert Number
LLCS108
HKY30R
(mm)
*2
WT
(12)
H63TH-PCMNN-H12
H63TH-PCMNN-L12
CNMo
CNGo 1204oo
NP-CNoA
(12)
*1
(kg)
LF
Wrench
*12 Clamp
* WT : Tool Weight
DCLN
(12)
CBN
Shim
Shim Pin Clamp Lever Clamp Screw
Plug
Wrench
100
1.7 LLSCN42
LLP14
LLCL14
LLCS108 HGM-PT1/8 HKY30R
140
2.7 LLSCN42
LLP14
LLCL14
*12 Clamp
* WT : Tool Weight
External turning
Facing
DOUBLE CLAMP type
Finish
FH
Light
Medium
LP
(12)
Medium
MK
MP
(12)
(12)
Medium
Medium Rough
DCMN
External turning
Facing
DOUBLE CLAMP type
(12)
MK
95
Light
Medium
LP
Medium
RP
Standard
Finish
FH
MP
(12)
(12)
Medium
Medium Rough
HSK-T TOOLS
H63TH-PCLNR/L-DX12
(mm)
LF WF
(12)
Stainless
MS

Stock
R L
HSK-T TOOLS
(12)
Medium
95
Order Number
RP
Standard
95
(12)
(12)
Stainless
CBN
(12)
MS
Stock
Dimensions
Insert Number
R L
H63TH-DCLNR/L-DX12
a a
(mm)
LF WF
(12)
(12)
*2
WT
Dimensions
Order Number
CNMo
CNGo 1204oo 65 45 1.3 LLSCN42
NP-CNoA
Shim Pin Clamp Bridge

LLP14
DCK2613
Spring
Clamp Screw
Wrench
DCS1
DC0621T
TKY20F
*1 Clamp Torque (N m) : DC0621T=5.0

*2 WT : Tool Weight
(12)
Stock
Insert Number
(mm)
H63TH-DCMNN-L12
CNMo
CNGo 1204oo
NP-CNoA
*1
(kg)
LF
H63TH-DCMNN-H12
(12)
*2
WT
Shim
Spring
Clamp Screw
Wrench
100
1.7 LLSCN42
LLP14
DCK2613
DCS1
DC0621T
TKY20F
140
2.7 LLSCN42
LLP14
DCK2613
DCS1
DC0621T
TKY20F
*1 Clamp Torque (N m) : DC0621T=5.0

*2 WT : Tool Weight
PCLN type inserts

DCLN type inserts
(12)
CBN
(12)
*1
(kg)
Shim
(12)
Stainless
MS
Order Number
CBN & PCD inserts

A092 A097
A092 A097
B022 B024, B055
A070
LEGEND FOR
STOCK STATUS MARK
REFERENCE PAGE

spread.

PRODUCT STANDARDS
Indicates order numbers,
stock status (per right/left
hand), applicable inserts,
dimensions, and spare parts.

H000
MP
Standard
MK
MS
Medium
LP
Medium
RP
95
H006
Light
FH
PCMN type inserts

DCMN type inserts
CBN & PCD inserts
A092 A097
A092 A097
B022 B024, B055

SPARE PARTS
TECHNICAL DATA
A070
P001
Q001
H007
PAGE REFERENCE
SPARE PARTS
TECHNICAL DATA
HSK-T TOOLS
OVERVIEW OF HSK-T TOOLS ....................... H002
CLASSIFICATION OF HSK-T TOOLS ............ H004
HSK-T TOOL STANDARDS
EXTERNAL TURNING FACING
CNooINSERTS TOOL HOLDERS .......................... H006

DNooINSERTS TOOL HOLDERS .......................... H011
EXTERNAL TURNING FACING BORING
CNooINSERTS TOOL HOLDERS .......................... H008

EXTERNAL TURNING COPYING
DNooINSERTS TOOL HOLDERS .......................... H009

EXTERNAL TURNING FACING COPYING
RCooINSERTS TOOL HOLDERS .......................... H012

FACING COPYING
VBooINSERTS TOOL HOLDERS .......................... H013

GROOVING
MG INSERTS TOOL HOLDERS .............................. H014

THREADING
MMT INSERTS TOOL HOLDERS............................ H016

MT INSERTS TOOL HOLDERS............................... H017
EXTERNAL TURNING TOOL HOLDERS ... H019
BORING BAR HOLDERS........................... H021
BORING BAR SLEEVES............................ H022

*H022
H100TH-Bpp-ppp
H020
H019
H008
H021
H008
H006
H007
H011
H009
H010
H020
H021
H019
H100TH-EN3232R/L-130
H100TH-EV3232R/L-180
H63TH-ApppDCLNR/L12
H63TH-Bpp-pp
H63TH-DCLNL-L12-3
H63TH-DCLNR/L-DX12
H63TH-DCMNN-H/L12
H63TH-DDJNL-L15-3
H63TH-DDJNR/L-DX15
H63TH-DDNNN-H/L15
H63TH-EN2525R/L-115
H63TH-EV2020R/L-105-3
H63TH-EV2525R/L-112
H014
H016
H016
H017
H006
H007
H009
H010
H012
H012
H013
H013
H022
H63TH-MGHR/L-DX43pp
H63TH-MMTENR-H/L16
H63TH-MMTER-DX16
H63TH-MTHR/L-DX43
H63TH-PCLNR/L-DX12
H63TH-PCMNN-H/L12
H63TH-PDJNR/L-DX15
H63TH-PDNNN-H/L15
H63TH-PRDCN-H/L12
H63TH-PRGCR/L-DX12
H63TH-SVPBR/L-DX16
H63TH-SVVBN-H/L16
SL32pp-90
H001
Tooling system
for turning on
multi-task machines
HSK TOOLS
High accuracy cutting
edge positioning
HSK-T System
The HSK-T type has a closer tolerance

between the spindle key and tool holder
keyway than the HSK-A type. This
results in higher cutting edge positional
accuracies. For milling, the conventional
HSK-A type tools can be still used.
HSK-T is a new HSK system designed

for turning on multi-task machines that
are compatible with HSK-A type (ISO
standard: ISO12164-1:2001).
The HSK system was developed
by a consortium of 17 Japanese
manufacturers and registered in ISO
standard (ISO12164-3:2008) under
the name HSK-T type in 2008 and JIS
standard (JIS B6064-3) in 2013.
HSK-T TOOLS
Compatible with both multi-task machines and machining centres
HSK-T
Turning tool holder
HSK-T spindle
Multi-task machines
HSK-A
Rotating tool holder
HSK-A spindle
Machining centre
Neck length
HSK-T63 Min.4mm
HSK-T100 Min.5mm
*Note
Short neck length from the flange with thick body of the
HSK-T turning tool as shown in the figure at the left.
Because there are machines which cannot be mounted
depending on the ATC specifications of the multi-task
machine(HSK-A type), please check beforehand.
Also be careful of interference of the magazine with adjacent
tools.
Neck thickness
HSK-T63 Max.62mm
HSK-T100 Max.99mm
HSK-T turning tool standard (Example)
Improved keyway tolerance

Tolerance comparison (Example)
Close tolerance
(mm)
0.10
12.25 Key tolerance 12.35
0.15 Minimum clearance
HSK
A63
0.08
Keyway
12.25 tolerance
0.33 Maximum clearance
12.2
Spindle key
Holder keyway
Maintains cutting edge height.

Higher machining accuracy.
H002
12.3
12.4
12.385
HSK
T63
0.025
12.5
12.58
12.6
12.41
Minimum clearance 0.015

0.035
12.425
12.46
0.075 Maximum clearance
High accuracy and rigidity HSK-T type tooling

system developed for use on multi-task machines.
Straight type tools suitable for use on multi-task machines
Improve centreline height by positioning the
cutting edge at the centre of the spindle.
By tilting the machines B

spindle (main axis of the tool)
at 45 deg, interference
between the spindle, holder,
workpiece and chuck can be
avoided.
Increased stability and

accuracy can be achieved
because the cutting edge
centreline height is not
affected by the gap between
the spindle and the key.
No interference
Clearance
Avoid workpiece interference with improved

tool accessibility.
Work face
Drive key
Drive keyway
New one-action type double clamp series

The double clamp mechanism offers high rigidity, accuracy and reliability that ensures secure insert clamping. There fore
making it suitable turning of difficult to machine materials such as stainless and heat resistant alloys.
Clamp bridge
Clamp screw
Spring
Shim
Handed type for
turning and facing
Straight type for

turning and facing
Shim pin
HSK-T TOOLS
Insert
For turning,
facing and boring
3 on 1 tool for process and tool consolidation

3 turning inserts of the same geometry can be installed on a single tool.
The same type of inserts can
be installed for quick change
with spare tools.
Different types of inserts can be
installed for different applications
(roughing, semi finishing and finishing)
Inserts in different grade types
can be installed to cover
various kinds of workpieces.
New HSK-T100 size for large workpieces

Larger tool holder sizes for high efficiency machining.
Square shank holder type
Boring bar / Drill type
Sleeve
A single tool can be used with different sized tool holders.

Available for use with JIS B4126 (ISO 5610) 32x32 and 32x25 tools.
Possible to fit a 25x25 tool by using a 7mm plate.
* Please prepare a plate on your own.
25x25 size tool

7mm plate
H003
HSK-T TOOLS
CLASSIFICATION OF HSK-T TOOLS

EXTERNAL TURNING FACING COPYING
Order Number
Cutting Mode
Order Number
H63TH-PCLNR/L-DX12
Cutting Mode
H63TH-PCMNN-H/L12
95
95
^ H006
^ H007
H63TH-DCLNR/L-DX12
H63TH-DCMNN-H/L12
95
95
^ H006
^ H007
H63TH-PDJNR/L-DX15
H63TH-PDNNN-H/L15
107
30
93
HSK-T TOOLS
^ H009
^ H010
H63TH-DDJNR/L-DX15
H63TH-DDNNN-H/L15
107
30
93
^ H009
^ H010
H63TH-SVPBR/L-DX16
H63TH-SVVBN-H/L16
117
30
117
30
^ H013
^ H013
H63TH-PRGCR/L-DX12
H63TH-PRDCN-H/L12
^ H012
^ H012
H63TH-DCLNL-L12-3
EXTERNAL TURNING FACING BORING

^ H008
95
Order Number
Cutting Mode
H63TH-A25KDCLNR/L12
H63TH-A32LDCLNR/L12
H63TH-DDJNL-L15-3
93
^ H011
H004
^ H008
95
GROOVING
EXTERNAL TURNING TOOL HOLDERS
Order Number
Cutting Mode
H63TH-MGHR/L-DX43oo
Order Number
Holder
H63TH-EV2525R/L-112
^ H014
^ H019
H100TH-EV3232R/L-180
THREADING
Cutting Mode
H63TH-MMTER-DX16
^ H016
H63TH-MMTENR-H/L16
^ H016
H63TH-MTHR/L-DX43
^ H019
H63TH-EN2525R/L-115
*1
^ H020
*1
^ H020
H100TH-EN3232R/L-130
HSK-T TOOLS
Order Number
H63TH-EV2020R/L-105-3
^ H017
^ H021
BORING BAR HOLDERS

Order Number
Holder
H63TH-Boo-oo
^ H021
H100TH-Boo-ooo
^ H022
SL32oo-90
(Sleeve)
*2
^ H022
Materials is licensed for production and distribution of these tools from MORI SEIKI CO., LTD under Patent No.3720202.
*12 Mitsubishi
* The SL32oo-90 sleeve is only for use with H100TH-B32-135.
H005
HSK-T TOOLS
PCLN
Finish
WF
63
FH
95
6
Light
Medium
LP
MP
(12)
(12)
(12)
Medium
Medium
Medium Rough
MK
RP
Standard
LF
(12)
(12)
Stainless
CBN
(12)
MS

Order Number
Stock
Dimensions
Insert Number
R L
H63TH-PCLNR/L-DX12
a a
(mm)
(12)
(12)
*1
*2
WT
(kg)
LF WF
CNMo
CNGo 1204oo 65 45 1.3
NP-CNoA
Shim
Shim Pin
LLSCN42
LLP14

LLCL14
LLCS108
Wrench
HKY30R
DCLN
External turning
Facing
DOUBLE CLAMP type
Finish
FH
WF
63
HSK-T TOOLS
*12 Clamp
WT : Tool Weight
*
95
Light
Medium
LP
MP
(12)
(12)
(12)
Medium
Medium
Medium Rough
MK
RP
Standard
LF
(12)
(12)
Stainless
CBN
(12)
MS
Order Number
Stock
Dimensions
Insert Number
R L
H63TH-DCLNR/L-DX12
a a
(mm)
LF WF
(12)
*2
WT
(12)
*1
(kg)
Shim
CNMo
CNGo 1204oo 65 45 1.3 LLSCN42
NP-CNoA

LLP14
DCK2613
Spring
Clamp Screw
Wrench
DCS1
DC0621T
TKY20F
Torque (N m) : DC0621T=5.0
*12 Clamp
WT : Tool Weight
*
PCLN type inserts

DCLN type inserts
a
H006
CBN & PCD inserts

A092 A097
A092 A097
B022 B024, B055
A070
PCMN
Finish
Light
FH
Medium
LP
MP
50
63
6
6
(12)
(12)
(12)
Medium
Medium
Medium Rough
MK
50
95
RP
Standard
LF
(12)
(12)
Stainless
CBN
(12)
MS
(12)
Dimensions
Order Number
Stock
Insert Number
(mm)
*2
WT
(kg)
LF
a
H63TH-PCMNN-L12
Shim
Plug
Wrench
100
1.7 LLSCN42
LLP14
LLCL14
140
2.7 LLSCN42
LLP14
LLCL14

2 WT : Tool Weight
DCMN
DOUBLE CLAMP type
External turning
Facing
Finish
FH
Light
Medium
LP
MP
HSK-T TOOLS
*
*
H63TH-PCMNN-H12
CNMo
CNGo 1204oo
NP-CNoA
(12)
1
50
63
(12)
(12)
(12)
Medium
Medium
Medium Rough
MK
RP
Standard
50
95
LF
(12)
(12)
Stainless
CBN
(12)
MS
(12)
Dimensions
Order Number
Stock
Insert Number
(mm)
*2
WT
*
*
H63TH-DCMNN-H12
H63TH-DCMNN-L12
*1
(kg)
LF
CNMo
CNGo 1204oo
NP-CNoA
(12)
Shim
Spring
Clamp Screw
Wrench
100
1.7 LLSCN42
LLP14
DCK2613
DCS1
DC0621T
TKY20F
140
2.7 LLSCN42
LLP14
DCK2613
DCS1
DC0621T
TKY20F
1 Clamp Torque (N m) : DC0621T=5.0

2 WT : Tool Weight
PCMN type inserts

DCMN type inserts
CBN & PCD inserts
A092 A097
A092 A097
B022 B024, B055

SPARE PARTS
TECHNICAL DATA
A070
P001
Q001
H007
HSK-T TOOLS
DCLN
DOUBLE CLAMP type
External turning
Facing
Light
Medium
LP
MP
63
(12)
(12)
(12)
Medium
Medium
Medium Rough
MK
RP
Standard
120
WF
12
12
95
Finish
FH
LF
(12)
(12)
Stainless
CBN
(12)
MS
Left hand tool holder only.

Order Number
Stock
Dimensions
(mm)
Insert Number
H63TH-DCLNL-L12-3
(12)
(12)
*2
WT
*1
(kg)
LF WF
Shim
CNMo
CNGo 1204oo 140 30 2.2 LLSCN42
NP-CNoA
LLP14
DCK2613
Spring
Clamp Screw
Wrench
DCS1
DC0621T
TKY20F
HSK-T TOOLS
*12 Clamp
WT : Tool Weight
*
DCLN
DOUBLE CLAMP type
External turning
Facing Boring
Finish
FH
Light
LP
Medium
MP
IN
DM
WF
63
95
(12)
(12)
(12)
Medium
Medium
Medium Rough
MK
Standard
RP
LU
GAMF
95
LF
(12)
(12)
Stainless
CBN
MS
Order Number
Stock
Dimensions
R L
H63TH-A25KDCLNR/L12
a a
H63TH-A32LDCLNR/L12
a a
LF
LU
CNMo
125 82
CNGo 1204oo
140 100
NP-CNoA
(12)
*2
DMIN WT
(mm)
Insert Number
(12)
(mm)
WF GAMF
(kg)
Shim
Shim
Pin
(12)
*1
Clamp
Clamp
Bridge Spring Screw Wrench
17
11
32
1.1 LLSCP42 LLP14 DCK2613 DCS1 DC0621T TKY20F
22
13
40
1.4 LLSCN42 LLP14 DCK2613 DCS1 DC0621T TKY20F
*12 Clamp
WT : Tool Weight
*
DCLN type inserts

a
H008
CBN & PCD inserts

A092 A097
B022 B024, B055
A070
PDJN
Finish
External turning Copying
63
(15)
MP
(15)
(15)
Medium Rough Stainless
MK
Medium
LP
Medium
WF
93
Light
FH
RP
MS
LF
(15)
(15)
G Class
CBN
(15)
R/L

Order Number
Stock
Dimensions
(mm)
Insert Number
R L
H63TH-PDJNR/L-DX15
a a
*3
WT
(15)
(15)
*1
(kg)
LF WF
DNMo
DNGo 1504oo 65 45 1.2
NP-DNoA
Shim
Shim Pin
LLSDN43
(LLSDN42)
LLP14

LLCL24
LLCS108
Wrench
HKY30R
DDJN
DOUBLE CLAMP type
Finish
FH
Medium
WF
93
Light
Medium
LP
(15)
63
External turning
Copying
MK
MP
(15)
HSK-T TOOLS
*12 Clamp
Please use shim no. LLSDN42 with 6.35mm thick inserts. When using 6.35mm thick inserts, the shim should be ordered separately.
*3 WT : Tool Weight
*
(15)

RP
MS
LF
(15)
(15)
G Class
CBN
(15)
R/L
Order Number
Stock
R L
H63TH-DDJNR/L-DX15
a a
Dimensions
Insert Number
(mm)
(15)
*2
*3
WT
(15)
*1
(kg)
LF WF
Shim
DNMo
LLSDN43
DNGo 1504oo 65 45 1.2
(LLSDN42)
NP-DNoA

LLP24
DCK2613
Spring
Clamp Screw
Wrench
DCS1
DC0621T
TKY20F
*12 Clamp
*3 WT : Tool Weight
*
CBN & PCD inserts

PDJN type inserts
DDJN type inserts
B025 B027, B055

A098 A103
A098 A103

SPARE PARTS
TECHNICAL DATA
A070
P001
Q001
H009
HSK-T TOOLS
PDNN
Finish
External turning Copying
Light
FH
MP
6230
63
(15)
6
107
30
Medium
LP
(15)
Medium
(15)
MK
RP
MS
6230
LF
(15)
(15)
G Class
CBN
(15)
R/L
Dimensions
Order Number
Stock
Insert Number
(mm)
LF
HSK-T TOOLS
*
*
*
H63TH-PDNNN-H15
H63TH-PDNNN-L15
DNMo
DNGo 1504oo
NP-DNoA
*3
WT
(15)
2
(15)
1
(kg)
Shim
Plug
Wrench
LLSDN43
LLCL24 LLCS108 HGM-PT1/8 HKY30R
1.6 (LLSDN42) LLP14
LLSDN43
LLCL24 LLCS108 HGM-PT1/8 HKY30R
2.5 (LLSDN42) LLP14
100
140

2 Please use shim no. LLSDN42 with 6.35mm thick inserts. When using 6.35mm thick inserts, the shim should be ordered separately.
3 WT : Tool Weight
DDNN
External turning
Copying
DOUBLE CLAMP type
Finish
FH
Light
Medium
LP
MP
6230
6
63
(15)
107
30
Medium
MK
(15)
(15)

RP
MS
6230
LF
(15)
(15)
G Class
CBN
(15)
R/L
Dimensions
Order Number
Stock
Insert Number
(mm)
LF
H63TH-DDNNN-H15
H63TH-DDNNN-L15
DNMo
DNGo 1504oo
NP-DNoA
100
140
*3
WT
(15)
*2
(15)
*1
(kg)
Shim
LLSDN43
DCK2613
1.6 (LLSDN42) LLP24
LLSDN43
LLP24
DCK2613
2.5 (LLSDN42)
Spring
Clamp Screw
Wrench
DCS1
DC0621T
TKY20F
DCS1
DC0621T
TKY20F
*12 Clamp
*3 WT : Tool Weight
*
CBN & PCD inserts

PDNN type inserts
a
H010
DDNN type inserts

B025 B027, B055

A098 A103
A098 A103
A070
DDJN
DOUBLE CLAMP type

6
Finish
63
WF
0
12
120
LP
6
3
93
Light
FH
(15)
(15)
Medium
Medium
MP
LF
120
MK
(15)
(15)

RP
Left hand tool holder only.

Order Number
Stock
L
H63TH-DDJNL-L15-3
Dimensions
Insert Number
(mm)
*3
WT
MS
(15)
2
(15)
1
(kg)
LF WF
Shim
DNMo
LLSDN43
DNGo 1504oo 140 30 2.2 (LLSDN42)
NP-DNoA

LLP24
DCK2613
Spring
Clamp Screw
Wrench
DCS1
DC0621T
TKY20F
HSK-T TOOLS
*12 Clamp
*3 WT : Tool Weight
*

DDNN type inserts
CBN & PCD inserts
A098 A103
B025 B027, B055
SPARE PARTS
TECHNICAL DATA
A070
P001
Q001
H011
HSK-T TOOLS
PRGC
Medium
External turning Facing Copying
WF
63
(12)
LF

Order Number
Stock
Dimensions
Insert Number
R L
H63TH-PRGCR/L-DX12
a a
(mm)
(kg)
LF WF
RCMX
*1
*2
WT
1204M0 65 45 1.2
Shim
Shim Pin
LLSRN123
LLP13

LLCL112
LLCS106
Wrench
HKY25R
PRDC
Medium
External turning Facing Copying

B2
(12)
63
HSK-T TOOLS
*12 Clamp
WT : Tool Weight
*
B2
LF
Dimensions
Order Number
Stock
Insert Number
(mm)
(kg)
LF B2
H63TH-PRDCN-H12
H63TH-PRDCN-L12
RCMX
1204M0
*1
*2
WT
Shim
Plug
Wrench
100 69 1.4 LLSRN123
LLP13
LLCL112
140 75 2.3 LLSRN123
LLP13
LLCL112
*12 Clamp
WT : Tool Weight
*

Work Material
Hardness
Cutting Mode
Breaker
Grade
Mild Steel
<180HB
Medium Cutting
Standard
UE6110
205 350
180HB350HB
Medium Cutting
Standard
UE6110
150 260
Stainless Steel
<200HB
Medium Cutting
Standard
US735
70 130
P
M
H012
PRGC type inserts

PRDC type inserts
A137
A137
SVPB
Finish
Facing Copying
WF
63
R/L-F
(16)
(16)
Medium
Medium
MV
2730
LF
MP
3.8
117
30
Light
SV
(16)
(16)
CBN

Order Number
Stock
Dimensions
Insert Number
R L
H63TH-SVPBR/L-DX16
a a
(mm)
*2
WT
(kg)
LF WF
VBMT
VBGT
(16)
1
1604oo 65 45 1.1
Shim
Shim Pin
Clamp Screw
Wrench
SPSVN32
BCP141
TS35D
TKY15F
SVVB
Finish
Facing Copying
R/L-F
Light
SV
63
B2
117
30
(16)
(16)
Medium
Medium
MV
B2
HSK-T TOOLS
Torque (N m) : TS35D=3.5
*12 Clamp
WT : Tool Weight
*
MP
LF
(16)
(16)
CBN
Dimensions
Order Number
Stock
(mm)
Insert Number
LF
H63TH-SVVBN-H16
H63TH-SVVBN-L16
VBMT
VBGT
1604oo
*2
WT
(16)
1
(kg)
B2
Shim
Shim Pin
Clamp Screw
Plug
Wrench
100 6630' 1.3
SPSVN32
BCP141
TS35D
HGM-PT1/8
TKY15F
140 7230' 2.2
SPSVN32
BCP141
TS35D
HGM-PT1/8
TKY15F
Torque (N m) : TS35D=3.5
*12 Clamp
WT : Tool Weight
*

Work Material
M
K
Hardness
Mild Steel
<180HB
Carbon Steel
Alloy Steel
180HB350HB
Stainless Steel
Gray Cast Iron
<200HB
Tensile Strength<350MPa
Cutting Mode
Finish Cutting
Medium Cutting
Finish Cutting
Medium Cutting
Medium Cutting
Medium Cutting
SVPB type inserts

SVVB type inserts
CBN inserts
Breaker
Grade

250 (150 300)
200 (150 250)
210 (150 260)
170 (120 210)
100 (70 120)
170 (140 200)
AP25N
MV
UE6020
F
MV
AP25N
UE6020
MV
US735
MV
UE6020
A148 A150
A148 A150
B048
SPARE PARTS
TECHNICAL DATA
P001
Q001
H013
HSK-T TOOLS
MG
Grooving
WF
63
CDX
CW
LF
Order Number
Stock
(mm)
Insert Number
R L
a a
43125
HSK-T TOOLS
MGTR/L
H63TH-MGHR/L-DX4323
a a
H63TH-MGHR/L-DX4333
a a
H63TH-MGHR/L-DX4315
43470
CW
CDX
1.25
1.2
1.45
1.5
1.5<CW<2.3
CW<3.3
2.3<
4.5
3.3<CW<4.7
4.5
*1
*2
WT
Dimensions
(kg)
LF WF
Clamp Bridge Clamp Screw
Spring
Wrench
65 45 1.2 MTK1R/L HBH06020
MES3
HKY40R
Torque (N m) : HBH06020=7.0
*12 Clamp
WT : Tool Weight
*

Work Material
Grade
Feed (mm/rev)
VP20MF
120 (100 140)
0.10 (0.03 0.18)
NX2525
130 (100 160)
0.12 (0.03 0.2)
Carbon Steel
Alloy Steel
180350HB
Stainless Steel
<200HB
VP20MF
120 (100 140)
0.10 (0.03 0.18)
Gray Cast Iron
VP20MF
120 (100 140)
0.10 (0.03 0.18)

H014
Hardness
INSERTS FOR MG TYPE

Dimensions (mm)
1.2
12.7
4.76
0.2
1.45
1.5
12.7
4.76
0.2
1.5
12.7
4.76
0.2
1.75
12.7
4.76
0.2
12.7
4.76
0.2
2.3
12.7
4.76
0.2
2.5
4.5
12.7
4.76
0.3
a a a r a a
MGTR/L43145
a r
MGTR/L43150
a a a a a a
MGTR/L43175
a a a r a a
MGTR/L43200
a a a a a a
MGTR/L43230
a a a a
MGTR/L43250
a a a a a a
MGTR/L43260
a r r
a a
2.6
4.5
12.7
4.76
0.3
MGTR/L43270
a r
a r
2.7
4.5
12.7
4.76
0.3
r a a
2.8
4.5
12.7
4.76
0.3
4.5
12.7
4.76
0.3
a a
3.2
4.5
12.7
4.76
0.3
r a a
3.3
4.5
12.7
4.76
0.3
MGTR/L43280
r a r
a a a a a a
MGTR/L43320
a
a
MGTR/L43300
MGTR/L43330
MGTR/L43350
a r a r a a
3.5
4.5
12.7
4.76
0.3
MGTR/L43400
a a a
a a
4.5
12.7
4.76
0.3
MGTR/L43420
a r r
a r
4.2
4.5
12.7
4.76
0.4
MGTR/L43430
a r r
a a
4.3
4.5
12.7
4.76
0.4
MGTR/L43450
a a a a a a
4.5
4.5
12.7
4.76
0.4
MGTR/L43470
a r r r a r
4.7
4.5
12.7
4.76
0.4
MGTR/L...
PDPT
RE
CBN Insert
RE
PDPT
HSK-T TOOLS
1.25
R L R L R L
MGTR/L43125
Geometry
RE
IC
IC
IC
PDPT
CW 0.025
CW
CW 0.03
MB8025
UTi20T
NX2525
Order Number
VP20MF
Stock
SPARE PARTS
TECHNICAL DATA
P001
Q001
H015
HSK-T TOOLS
MMTE
WF
63
Threading
LF

Order Number
Dimensions
Stock
(mm)
Insert Number
H63TH-MMTER-DX16
*2
WT
*1
(kg)
LF WF
Clamp Bridge Clamp Screw Stop Ring
MMT16ER ooooo 65 45 1.2
SETK51
SETS51
CR4
Shim
Shim Screw
CTE32TP15 HFC03008
Wrench
zTKY15F
xHKY20R
MMTEN
Threading
63
HSK-T TOOLS
Torque (N m) : SETS51=3.5, HFC03008=1.5

*12 Clamp
WT : Tool Weight
*
*1
LF
Tool holder for right hand insert only.

Dimensions
Order Number
Stock
Insert Number
(mm)
WT
*2
(kg)
LF
H63TH-MMTENR-H16
Clamp Bridge Clamp Screw Stop Ring
Shim
Shim Screw
Plug
Wrench
100
1.7 SETK51 SETS51
CR4
CTE32TP15 HFC03008 HGM-PT1/8
zTKY15F
xHKY20R
140
2.7 SETK51 SETS51
CR4
CTE32TP15 HFC03008 HGM-PT1/8
zTKY15F
xHKY20R
MMT16ER ooooo
H63TH-MMTENR-L16
use with B axis tilted at 45 degrees.

*12 For
Clamp Torque (N m) : SETS51=3.5, HFC03008=1.5
*3 WT : Tool Weight
*

Work Material
H016
Hardness
Grade
VP10MF
150 (70 230)

100 (60 140)
140 (80 200)
100 (60 140)
130 (80 180)
80 (40 120)
140 (80 200)
90 (60 120)
Mild Steel
<180HB
Carbon Steel
Alloy Steel
180350HB
VP10MF
VP15TF
Stainless Steel
<200HB
VP10MF
VP15TF
Gray Cast Iron
VP10MF
VP15TF

VP15TF
APPLICABLE INSERT
G014, G016, G018, G020
MT
WF
63
Threading
LF
Right hand tool

holder shown.
Order Number
Stock
Dimensions
Insert Number
R L
H63TH-MTHR/L-DX43
a a
MTTR/L
43oooo
(mm)
LF
WF
65
45
*1
*2
WT
(kg)
1.2
Clamp Bridge
Clamp Screw
Spring
Wrench
MTK1R/L
HBH06020
MES3
HKY40R
HSK-T TOOLS
Torque (N m) : HBH06020=7.0
*12 Clamp
WT : Tool Weight
*

Work Material
Hardness
P
Mild Steel
Carbon Steel
Alloy Steel
<180HB
180HB350HB
M
Stainless Steel
UP20M
140 (100 180)
NX2525
200 (150 250)
UTi20T
120 (100 150)
UP20M
120 (100 150)
NX2525
170 (150 200)
UTi20T
100 (70 120)
UP20M
120 (80 150)
UTi20T
100 (70 130)
UP20M
80 (60 100)
UTi20T
80 (60 100)
<200HB
K
Gray Cast Iron
Grade
100 (70 130)
HTi10
APPLICABLE INSERT

a
SPARE PARTS
TECHNICAL DATA
H018
P001
Q001
H017
HSK-T TOOLS

INSERTS FOR MT TYPE
1.01.75
12.7
4.76
0.1
1.01.75
12.7
4.76
0.1
2.02.5
12.7
4.76
0.2
2.02.5
12.7
4.76
0.2
3.03.5
12.7
4.76
0.3
G
G
12.7
12.7
4.76
4.76
0.3
0.4
G
G
G
3.03.5
4.04.5
(2810)
(168)
(118)
12.7
12.7
12.7
4.76
4.76
4.76
0.1
0.2
0.3
G
r
MTTR/L(60) (G Class)
RE
MTTR/L(55) (G Class)
RE
IC
4.76
IC
12.7
Geometry
RE
60
0.8
IC
55
HTi10
UTi20T
MTTR436000
MTTR436001
MTTL436001
MTTR436002
MTTL436002
MTTR436003
MTTL436003
MTTR436004
MTTR435501
MTTR435502
MTTR435503
UP20M
Class
Order Number
Dimensions (mm)
ISO
Pitch mm
(thread/inch)
NX2525
General 55
General 60
Type
HSK-T TOOLS
y STANDARD DEPTH OF CUT
aThe chart on the right shows the cutting
H/4
h2
h1
P (Pitch)
h1
h2
r (Corner Radius)
Number of Passes

aWhen you use cermet grades or cut
a METRIC THREAD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
0.75
0.46
0.35
0.11
0.18
0.13
0.10
0.05
1.00
0.61
0.47
0.14
0.20
0.15
0.10
0.10
0.06
Unit : mm
1.25
0.77
0.59
0.18
0.20
0.18
0.12
0.12
0.10
0.05
1.50
0.92
0.70
0.22
0.25
0.20
0.15
0.15
0.10
0.07
1.75
1.07
0.82
0.25
0.25
0.20
0.20
0.15
0.12
0.10
0.05
2.00
1.23
0.94
0.29
0.25
0.25
0.20
0.15
0.15
0.10
0.08
0.05
2.50
1.53
1.17
0.36
0.30
0.25
0.20
0.20
0.15
0.10
0.10
0.10
0.08
0.05
3.00
1.84
1.41
0.43
0.30
0.25
0.25
0.20
0.20
0.15
0.15
0.10
0.10
0.09
0.05
3.50
2.15
1.65
0.50
0.35
0.30
0.25
0.20
0.20
0.20
0.15
0.15
0.10
0.10
0.10
0.05
(Note) The first pass causes a high load on the cutting edge.
In order to avoid damage, keep the depth of cut to 0.4 0.5mm maximum.

H018
4.00
2.45
1.87
0.58
0.35
0.30
0.25
0.25
0.25
0.20
0.20
0.15
0.15
0.10
0.10
0.10
0.05
4.50
2.76
2.11
0.65
0.40
0.35
0.30
0.25
0.25
0.20
0.20
0.15
0.15
0.15
0.10
0.10
0.10
0.06

h1
y This holder is for 2525 size tools.
Please shorten the tool as shown below

before use.
Cut
WF
S6
b1
63
b2
h2
LSCX
H
LB
LF
115
35
(150)

Stock
Order Number
Dimensions (mm)
WT
H63TH-EV2525R/L-112
LF
LB LSCX
150 112
77
h1
h2
WF
S6
b1
b2
25
32
53
45
13
38
32
Clamp Screw
Plug
HSS12025
HGM-PT1/8
3.9
* WT : Tool Weight
h1
y This holder is for 3232 and 3225
WF
b1
S6
100
b2
h2
HSK-T TOOLS
(kg)
size tools.
LSCX
LB
LF

Order Number
H100TH-EV3232R/L-180
Stock
Dimensions (mm)
WT
(kg)
LF
LB
LSCX
h1
h2
WF
S6
b1
b2
220 180 130
32
40
68
57
17
46
43 11.7
Clamp Screw
Plug
HSS14035
HSS06006
WT : Tool Weight
(Note) Possible to fit a 25 x 25 tool by using a 7mm plate.
SPARE PARTS
TECHNICAL DATA
P001
Q001
H019
HSK-T TOOLS

b2
63

before use.
LF
b1
LU
Cut
H
h2
h1
LB
110
40
(150)
Mitsubishi Materials is licensed for production and

distribution of these tools from MORI SEIKI CO., LTD
under Patent No.3720202.
Stock
Dimensions (mm)
WT
(kg)
H63TH-EN2525R/L-115
LB
LU
LF
h1
h2
b1
b2
115
40
110
25
32
53
45
45
Clamp Screw
Plug
HSS12030
HSS06006
3.7
* WT : Tool Weight
b1
LU
100
b2
HSK-T TOOLS
Order Number
y This holder is for 3232 and 3225 size tools.
LF

before use.
H
h2
Cut
h1
LB
110
60
(170)
Mitsubishi Materials is licensed for production and

distribution of these tools from MORI SEIKI CO., LTD
under Patent No.3720202.
Order Number
H100TH-EN3232R/L-130
Stock
R
LB
LU
LF
h1
h2
b1
b2
130
40
110
32
32
68
47
43
H020
WT
(kg)
WT : Tool Weight
(Note) Possible to fit a 25 x 25 tool by using a 7mm plate.
Dimensions (mm)
6.6
Clamp Screw
Plug
HSS14030
HSS06006
63
WF

before use.
12
b1
S6
120
BD
LSCX
LB
LF
Cut
105
20
(125)
H63TH-EV2020R/L-105-3
Stock
Dimensions (mm)
WT
(kg)
LF
LB LSCX
140 105
70
BD
WF
S6
b1
20
90
40
15
35
Clamp Screw
Nozzle Plug
Plug
HSS12030
HSS05012
HSS06006
2.9
* WT : Tool Weight
BORING BAR HOLDERS
HSK-T TOOLS
Order Number
BD
63
Boring
LF
DCB
CBDP
Dimensions (mm)
Order Number
Stock
H63TH-B08-65
28
H63TH-B10-70
H63TH-B12-70
WT
(kg)
BD
DCB
LF
CBDP
65
40
M8
0.9
HSS08010
35
10
70
45
M8
1.0
HSS08012
42
12
70
45
M8
1.1
HSS08012
H63TH-B16-75
48
16
75
50
M10
1.3
HSS10016
H63TH-B20-75
52
20
75
50
M10
1.4
HSS10016
H63TH-B25-83
62
25
83
58
M12
1.7
HSS12016
H63TH-B32-87
62
32
87
62
M12
1.7
HSS12016
H63TH-B40-97
65
40
97
72
M16
1.8
HSS16012
Clamp Screw
WT : Tool Weight
(Note) Please shorten a boring bar to the required shank length. This holder is for boring bars and indexable type drills.
SPARE PARTS
TECHNICAL DATA
P001
Q001
H021
HSK-T TOOLS
BORING BAR HOLDERS

BD
100
Boring
LB
DCB
CBDP
Dimensions (mm)
Stock
WT
(kg)
BD
DCB
LB
CBDP
Clamp Screw
H100TH-B25-120
62
25
120
88
12
3.9
HSS12016
H100TH-B32-135
72
32
135
102
12
4.8
HSS12018
H100TH-B40-150
82
40
150
117
16
5.9
HSS16020
H100TH-B50-180
92
50
180
147
16
7.7
HSS16020
WT : Tool Weight
(Note) Please shorten a boring bar to the required shank length. This holder is for boring bars and indexable type drills.
DCON
BORING BAR SLEEVES FOR H100TH-B32-135
DCB
HSK-T TOOLS
Order Number
FLGT
Order Number
OAL
Dimensions (mm)
Stock
WT
(kg)
DCB
DCON
OAL
FLGT
Clamp Screw
SL3208-90
32
95
0.6
HSS06008
SL3210-90
10
32
95
0.5
HSS08008
SL3212-90
12
32
95
0.5
HSS08008
SL3216-90
16
32
95
0.5
HSS08006
SL3220-90
20
32
95
0.4
HSS08005
WT : Tool Weight
(Note) These sleeves are only compatible with H100TH-B32-135 holder.
H022
SPARE PARTS
TECHNICAL DATA
P001
Q001
TURNING TOOLS
BRAZED TOOLS
CARBIDE BLANK FOR TURNING TOOLS ............................ I002
CARBIDE RODS (MITSUBISHI STANDARD)......................... I004
BRAZED TOOL HOLDERS ..................................................... I005
I001
BRAZED TOOLS
CARBIDE BLANK FOR TURNING TOOLS

Stock
P
Order
Number
HTi20
(HW-K20)
HTi10
(HW-K10)
HTi05T
(HW-K01)
HTi03A
(HW-K01)
UTi20T
(HW-M20)
01-0
10
01-1
13
01-2
16
11
01-3
19
13
01-4
22
15
01-5
25
17
For 31,32 Type
01-6
30
20
02 Type
02-0
10
02-1
13
02-2
16
11
02-3
19
13
02-4
22
15
25
17
02-6
30
20
03 Type
03-0
10
03-1
12
03-2
15
03-3
18
03-4
24
03-5
24
03-6
28
04-0
10
04-1
13
04-2
16
11
04-3
19
13
04-4
22
15
04-5
25
17
04-6
30
20
05-1
05-2
10
05-3
12
05-4
16
05-5
10
18
05-6
11
20
06-0
10
10
06-1
13
13
2.5
06-2
16
16
06-3
19
19
06-4
22
22
06-5
25
25
06-6
30
30
02-5
For 41,42 Type
For 37,38,47 Type
04 Type
For 33,34 Type
05 Type
60
For 49,51 Type
06 Type
40
C
For 36,39,40 Type
*(
) : Materials for cemented carbide tools and the classification for usage.
I002
STi40T
(HW-P40)
01 Type
BRAZED TOOLS
STi20
(HW-P20)
Geometry
Dimensions (mm)
STi10
(HW-P10)
Type

: Non stock, produced to order only.
Stock
P
HTi20
(HW-K20)
HTi10
(HW-K10)
08 Type
HTi05T
(HW-K01)
For 35 Type
HTi03A
(HW-K01)
UTi20T
(HW-M20)
80
STi40T
(HW-P40)
07 Type
STi20
(HW-P20)
Order
Number
Geometry
Dimensions (mm)
STi10
(HW-P10)
Type
07-0
10
10
07-1
13
13
07-2
16
16
07-3
19
19
07-4
25
20
07-5
25
22
07-6
30
25
08-1
08-3
13
08-4
15
08-5
17
08-6
20
09E1
20
10
For 43 Type
09E Type
B
30
For 95 Type
*(
) : Materials for cemented carbide tools and the classification for usage.
BRAZED TOOLS
10
I003
BRAZED TOOLS
CARBIDE RODS
L
LRB SERIES
Order Number
HTi10
TF15
MF10
Stock
LRB030
LRB040
LRB050
LRB060
LRB070
LRB080
LRB100
LRB120
a a a
a a a
a a a
a a a
a a a
a a a
a a a
3
4
5
6
7
8
10
12
330
330
330
330
330
330
330
330
Symbol
Dimensions (mm)
Tolerance (mm)
0.52.5
+0.5
+0.2
+0.5
+0.3
+0.6
+0.3
38
1012
Symbol
Dimensions (mm)
Tolerance (mm)
Bend (mm)
240
+10
0
+10
0
0.15
330
BRAZED TOOLS
a a a
Dimensions (mm)
I004
: Inventory maintained in Japan. (LRB030~LRB080:10pcs/case LRB100&LRB120:5pcs/case)
0.3
BRAZED TOOL HOLDERS

Stock
6
L
15
B
A
15
H
33
34
Type(Right Hand)
Type(Left Hand)
8
B
H
33, 34-0
6
35 Type
80
HTi20
HTi10
HTi05T
UTi20T
STi40T
STi20
Shank
STi10
31 Type(Right Hand)
32 Type(Left Hand)
Dimensions (mm)
Carbide
10
10
80 2.7 10
3 0.3 01-0
10
10
80 2.7 10
3 0.3 01-0
31-0
32-0
31-1
13
13
100 4
13
3 0.5 01-1
32-1
13
13
100 4
13
3 0.5 01-1
31-2
16
16
120 4.5 16
11
4 0.5 01-2
32-2
16
16
120 4.5 16
11
4 0.5 01-2
31-3
19
19
140 5.5 19
13
5 0.5 01-3
32-3
19
19
140 5.5 19
13
5 0.5 01-3
31-4
25
25
160 6.5 22
15
6 1
01-4
32-4
160 6.5 22
15
6 1
01-4
33-0
a
a
a
a
25
25
10
10
a
a
80
80
10
3 0.3 04-0
34-0
33-1
34-1
33-2
34-2
33-3
34-3
33-4
34-4
33-5
34-5
33-6
30
35
200 6
30
20
8 1
04-6
34-6
30
35
200 6
30
20
8 1
04-6
35-0
10
10
80
10
10
3 0.3 07-0
35-1
13
13
100
13
13
3 0.5 07-1
35-2
16
16
120
16
16
4 0.5 07-2
35-3
19
19
140
19
19
5 0.5 07-3
35-4
25
25
160
25
20
6 1
07-4
36-0
10
10
80
10
10
3 2
06-0
36-1
13
13
100
13
13
3 2.5 06-1
36-2
16
16
120
16
16
4 3
06-2
36-3
19
19
140
19
19
5 4
06-3
36-4
36-5
36-6
10
10
10
3 0.3 04-0
13
13
100 4
13
3 0.5 04-1
13
13
100 4
13
3 0.5 04-1
16
16
120 4
16
11
4 0.5 04-2
16
16
120 4
16
11
4 0.5 04-2
19
19
140 5
19
13
5 0.5 04-3
19
19
140 5
19
13
5 0.5 04-3
25
25
160 5
22
15
6 1
04-4
25
25
160 5
22
15
6 1
04-4
25
30
180 6
25
17
7 1
04-5
25
30
180 6
25
17
7 1
04-5
BRAZED TOOLS
Order
R/L
Number
Geometry
Blank No.
B
6
C
Double Sided
Relief
36 Type
40
L
6
Double Sided
C
Relief
25
160
22
22
6 4
06-4
25
30
180
25
25
7 5
06-5
30
35
200
30
30
8 6
06-6
25
I005
BRAZED TOOLS
BRAZED TOOL HOLDERS

Stock
R
160
60
Double Sided
Relief
39 Type(Right Hand)
40 Type(Left Hand)
150
BRAZED TOOLS
40
6
C
Double Sided
Relief
41 Type(Right Hand)
42 Type(Left Hand)
45
R
A
R
135
H
B
6
C
37-3
38-3
37-4
38-4
39-0
a
a
HTi20
STi40T
HTi10
38-2
HTi05T
37-2
UTi20T
STi20
38-1
Carbide
13
13
100
12
3 0.5 03-1
13
13
100
12
3 0.5 03-1
16
16
120
15
4 0.5 03-2
16
16
120
15
4 0.5 03-2
19
19
140
18
5 0.5 03-3
19
19
140
18
5 0.5 03-3
25
25
160
10
24
6 1
03-4
25
25
160
10
24
6 1
03-4
10
10
80
10
10
3 2
06-0
06-0
37-1
Shank
STi10
37 Type(Right Hand)
38 Type(Left Hand)
Right hand tool

holder shown.
Dimensions (mm)
Order
R/L
Number
Geometry
Blank No.
a
a
10
10
80
10
10
3 2
13
13
100
13
13
3 2.5 06-1
40-0
39-1
40-1
39-2
40-2
39-3
40-3
39-4
40-4
41-0
41-1
42-1
41-2
13
13
100
13
13
3 2.5 06-1
16
16
120
10
16
16
4 3
06-2
16
16
120
10
16
16
4 3
06-2
19
19
140
12
19
19
5 4
06-3
19
19
140
12
19
19
5 4
06-3
25
25
160
13
22
22
6 4
06-4
25
25
160
13
22
22
6 4
06-4
10
10
80
10
3 0.3 02-0
13
13
100
13
3 0.5 02-1
13
13
100
13
3 0.5 02-1
16
16
120
10
16
11
4 0.5 02-2
16
16
120
10
16
11
4 0.5 02-2
19
19
140
12
19
13
5 0.5 02-3
42-2
41-3
42-3
19
19
140
12
19
13
5 0.5 02-3
41-4
25
25
160
13
22
15
6 1
02-4
42-4
25
25
160
13
22
15
6 1
02-4
43-1
10
16
100
13
08-1
43-2
13
19
120
16
08-1
43-3
16
22
140
20
13
08-3
43-4
19
25
160
25
15
08-4
43-5
22
32
180
30
17
08-5
a
a
43 Type
E
B
I006
Stock
M
Dimensions (mm)
Order
R/L
Number
HTi05T
HTi10
47-1
13 13 140 12
50 10
3 0.5 03-0
47-2
16 16 160 15
60 12
3 0.5 03-1
47-3
19 19 190 18
80 15
4 0.5 03-2
47-4
25 25 230 22 10 100 18
5 1
03-3
49-1
13 13 100
05-1
49-2
16 16 120
6 10
05-2
49-3
19 19 140
7 12
05-3
49-4
25 25 160
9 16
05-4
51-1
13 13 140 12
50
05-1
51-2
16 16 160 15 10
60
6 10
05-2
51-3
19 19 190 18 12
80
7 12
05-3
95-1
25 25 160
UTi20T
Carbide
STi20
47Type (Right Hand)
Shank
STi10
Geometry
Blank No.
H
R
A
60
158 10
Double Sided
Relief
C
Double
Sided
Relief
6030'
49Type (Right Hand)
a
a
L
B
51Type (Right Hand)

I
BRAZED TOOLS
A
6030'
L
H
95Type
20 10
7 1
09E1
30
6
R
L
H
I007

OF SOLID END MILLS
zOrganized according to cutting mode for milling. (Refer to END MILL LIST.)
PHOTO OF PRODUCT
PRODUCT TITLE
ITEM NUMBER
PRODUCT BLOCK
MSTAR END MILLS
CARBIDE
MS2SS
UWC
End mill, Short cut length, 2 flute

Carbon Steel, Alloy Steel, Cast Iron Tool Steel, Pre-Hardened Steel,Hardened Steel
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
MS
30
DC<3
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DC > 3
Aluminium Alloy
DC
SQUARE
15(10 for 0.1)
DCON(h6)
Type1
APMX
GEOMETRY
DC
LF
DCON(h6)
Type2
BALL
APMX
h6
DC=0.1
DC>0.1
0
- 0.010
0
- 0.020
LF
4<DCON<6 8<DCON<10 DCON=12

0
- 0.008
0
- 0.009
0
- 0.011
PRODUCT FEATURES
a 2 flute end mill for general use.
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
MS2SSD0010
MS2SSD0020
MS2SSD0030
MS2SSD0040
MS2SSD0050
MS2SSD0060
MS2SSD0070
MS2SSD0080
MS2SSD0090
MS2SSD0100
MS2SSD0120
MS2SSD0150
MS2SSD0180
MS2SSD0200
MS2SSD0250
MS2SSD0300
MS2SSD0400
MS2SSD0500
MS2SSD0600
MS2SSD0700
MS2SSD0800
MS2SSD0900
MS2SSD1000
MS2SSD1100
MS2SSD1200
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.2
1.5
1.8
2
2.5
3
4
5
6
7
8
9
10
11
12
0.15
0.3
0.45
0.6
0.75
0.9
1.1
1.2
1.4
1.5
1.8
2.3
2.7
3
3.8
4.5
6
7.5
9
10.5
12
13.5
15
16.5
18
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
50
50
50
60
60
70
70
75
75
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
8
8
10
10
12
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
J048

PRODUCT STANDARDS
indicates order numbers, dimensions,
and stock status.
aTo Order:
For solid-carbide drill or brazed drill, please specify zorder number.
J000
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
2
1
2
MILLING TOOLS
SOLID END MILLS

IDENTIFICATION ..............................................J002
SYMBOL DESCRIPTIONS ...............................J003
COATING TECHNOLOGY ................................J004
..................................................J006
END MILLS SELECTION CHART ....................J024
SOLID END MILLS STANDARD
CARBIDE
SQUARE.................................... J048
BALL ......................................... J205
RADIUS ..................................... J287
TAPER ....................................... J355
TAPER BALL ............................ J367
CHAMFERING........................... J377

*J095
J399 KMH
C2JS
J100
J096
J098
J269
J104
J092
J102
J091
J124
J304
J174
J175
J173
J267
J302
J123
J195
J254
J298
J081
J083
J256
J300
J166
J193
J306
J260
J261
J278
J167
J168
J171
J172
J345
J086
J265
J387
J410
J404
J192
J428
J414
J436
J431
C2LA
C2LS
C2MA
C2MB
C2MHA
C2MS
C2SA
C2SS
C3SA
C3SARB
C4JC
C4LC
C4MC
CBN2XLB
CBN2XLRB
CMH
CMRA
CRN2MB
CRN2MRB
CRN2MS
CRN2XL
CRN2XLB
CRN2XLRB
CRN4JC
CSRA
CSRARB
DF2MB
DF2XLB
DF3XB
DF4JC
DF4XL
DFC4JC
DFCJRT
DFPSRB
DLC2MA
DLC2MB
G2MS
G4LC
G4MC
GBE
GMR
GSFPR
IMX
JR
J432
J207
J206
J205
J209
J430
J434
J065
J054
J056
J219
J052
J287
J049
J355
J367
J217
J048
J058
J062
J221
J290
J110
J141
J135
J360
J369
J133
J308
J132
J137
J130
J127
J311
J108
J126
J385
J396
J408
J402
J089
J088
J106
J177
LR
MP2MB
MP2SB
MP2SSB
MP2XLB
MR
MRB
MS2ES
MS2JS
MS2LS
MS2MB
MS2MD
MS2MRB
MS2MS
MS2MT
MS2MTB
MS2SB
MS2SS
MS2XL
MS2XL6
MS2XLB
MS2XLRB
MS3ES
MS4EC
MS4JC
MS4LT
MS4LTB
MS4MC
MS4MRB
MS4SC
MS4XL
MSJHD
MSMHD
MSMHDRB
MSMHZD
MSSHD
S2MD
S2SDA
S4JC
S4MD
SED2KMG
SED2KPG
SEE2L
SEE4L
CARBIDE
INDEXABLE HEAD END MILLS ... J436
HSS
SQUARE.................................... J378
BALL ......................................... J434
J179
J426
J381
J380
J400
J422
J424
J418
J397
J420
J416
J377
J243
J079
J248
J249
J076
J245
J246
J074
J276
J162
J337
J285
J160
J335
J373
J189
J191
J339
J188
J164
J121
J342
J292
J202
J251
J067
J069
J229
J232
J233
J228
J227
J071
SEG4SA
SR
VA2MS
VA2SS
VA4MC
VAJR
VALR
VAMFPR
VAMH
VAMR
VASFPR
VC2C
VC2ESB
VC2JS
VC2MB
VC2MDB
VC2MS
VC2PSB
VC2PSBP
VC2SS
VC3MB
VC4JC
VC4JRB
VC4MB
VC4MC
VC4SRB
VC4STB
VC6MH
VC8MH
VCHFRB
VCLD
VCMDSC
VCMH
VCMHDRB
VCPSRB
VCSFPR
VCXB
VF2MD
VF2MV
VF2SB
VF2SDB
VF2SDBL
VF2SSB
VF2WB
VF2XL
J237
J236
J271
J281
J143
J145
J279
J183
J187
J348
J353
J204
J190
J354
J314
J315
J148
J185
J351
J199
J146
J150
J325
J327
J184
J350
J197
J201
J283
J155
J151
J328
J333
J112
J118
J180
J157
J379
J378
J391
J394
J389
J383
J412
J406
VF2XLB
VF2XLBS
VF3XB
VF4MB
VF4MD
VF4MV
VF4SVB
VF6MHV
VF6MHVCH
VF6MHVRB
VF6MHVRBCH
VF6SVRCH
VF8MHVCH
VF8MHVRBCH
VFFDRB
VFHVRB
VFJHV
VFMD
VFMDRB
VFMFPR
VFMHV
VFMHVCH
VFMHVRB
VFMHVRBCH
VFSD
VFSDRB
VFSFPR
VFSFPRCH
VQ4SVB
VQJHV
VQMHV
VQMHVRB
VQMHVRBF
VQMHZV
VQMHZVOH
VQSVR
VQXL
1LA
1MA
2LS
2MK
2MS
2SS
4LC
4MC
J001
SOLID END MILLS
IDENTIFICATION
ORDER NUMBER OF END MILLS
MS 2 M S D0100
End mill names
Number of
flutes
VQ : SMART MIRACLE End Mills
1 : 1flute
ES : Extra short
2 : 2flute
3 : 3flute
M : Medium
4 : 4flute
: Semi long
5 : 5flute
: Long
VF
MP :
: Impact Miracle end mills

MS Plus End Mills
MS : Mstar end mills

VC
: Miracle end mills
Flute length
: Short
Features
Dimensions
Others
* * * * : Diameter
diameter
* * :: Shank
Neck length
***
angle
T
* * * * : Taper
one side
: General-use
: For stainless steel
ex.
: For keyway
D0050 |& 0.5
: For light alloy
D0500 |& 5
: Center cut
CRN : CRN coated end mills
6 : 6flute
XL : Long neck
: For deep cut
DLC : DLC coated end mills
8 : 8flute
: Taper neck
DFC : CVD diamond coated end mills
SX : Extra long
: Irregular spiral
helix angle
ex.
: Ball nose
R0050 | R0.5
: Roughing
R0500 | R5
DF
: Diamond coated end mills
MX : Extra long
CBN : CBN end mills

C
: Carbide end mills
VA
: Violet end mills
: TiN coated end mills
: KHAS end mills
of
* * * * : Radius
ball nose
**
***
: Flute length
: Overall Length
FPR : Fine roughing

: High helix
H
T
: Taper
TB
: Taper ball nose
RB : Corner radius
(High-grade powder high-speed steel)

K
***
CH : Coolant hole
: KHA end mills

(Powder metallurgy HSS)
: 3mm shank
: 6mm shank
SOLID END MILLS
None : Cobalt high-speed steel
*Other types are available by special order.
SE
End mill names
E
Helix angle
Number of flutes
Diameter
S
Shape
SZ : Super square
D : 30
2 : 2flute
ex.
: Short
BZ : Super ball
E : 45
4 : 4flute
010 |&1
: Standard
SE : Square end mill
G : Irregular spiral
050 |&5
: Long
helix angle
(38/41)
*Other types are available by special order.
J002
040
KP : For key way (+)

KM : For key way ( - )
G
Coating
G : (Al, Ti)N Coating
SYMBOL DESCRIPTIONS
UWC
CBN
KHA S
KHA
CO HSS
HSS
Ultra micro grain carbide
Ultra micro grain carbide is used as the substrate

material.
Cubic boron nitride
Mitsubishis original CBN is used.
Coating
VQ
VF
(Al, Cr)N coaitng optimum for difficult-to-cut

materials.
IMPACT MIRACLE Coating
Single phase nano crystal coating technology for

higher film hardness and heat resistance.
High hardness powder metallurgy HSS
(Al,Ti,Cr)N multilayer coating
Powder metallurgy HSS
(Al,Ti)N Coating
High hardness powder metallurgy HSS is used as the

substrate material.
Offers higher versatility for carbon steel, alloy steel

and hardened steel.
Powder metallurgy HSS is used as the substrate

material.
Cobalt high speed steel is used as the substrate

material.
High speed steel
High speed steel is used as the substrate material.
Tolerances
Outside diameter tolerance
(Al,Ti)N offers higher versatility.
VC
CRN
DLC
Indicates diameter tolerance of end mill.
R tolerance
R tolerance
Indicates the radial tolerance of an end mill with a

corner radius.
Tolerance of Taper angle
Indicates the tolerance of the point angle.
R tolerance
Indicates the radial tolerance of a corner radius

end mill.
Shank diameter tolerance
Indicates the shank diameter tolerance of end mill.
The original Miracle (Al,Ti)N coating.

Also suitable for dry cutting.
CRN Coating
Newly developed CrN coating for Copper

Electrodes machining.
DLC Coating
Hardness similar to that of CVD diamond coating

achieved with high adhesion strength.
(Jointly developed with NAGATA SEIKI CO.,LTD.)
CVD diamond coated end mills
DF
Diamond Coating
Indicates the tolerance of the taper angle.
Tolerance of Point angle
MIRACLE Coating
DFC
Indicates the radial tolerance of a ball nose end mill.
h6
SMART MIRACLE Coating
Suitable for CFRP
Suitable for graphite machining.
SOLID END MILLS
Tool material
VIOLET Coating
Increased tool life of 23 times that of TiN coated

products.
TiN Coating
Increased tool life of 23 times that of non coated

products.
Angle, sharp corner edge and gash land

10
Helix angle
Indicates the helix angle of the end mill.
Sharp corner edge
Indicates the end mill has a sharp corner edge.
Gash land
Indicates the end mill cutting edge has a gash land.
J003
SOLID END MILLS
COATING TECHNOLOGY
VQ SMART MIRACLE Coating
Newly-developed (Al,Cr)N coating with improved wear resistance.

The smoothig treatment of the coating layer reduces the cutting resistance and improves chip
discharge significantly. This next-generation coating offers longer tool life and higher efficiency in
machining difficult-to-cut materials.
Smoothed surfaceZero- Surface

Newly developed(Al,Cr)N coating
Super fine grade substrate
ZERO- Surface
ZERO-
Surface
The original surface treatment technology offers

smooth coatng layer. A good balance of smooth
surface and sharpe edge allows smooth chip
discharge and reduces the cutting resistance.
Machining efficiency and tool life is improved.
SOLID END MILLS
SMART MIRACLE Coating
VF
Coating
For higher hardness, higher speed and longer tool life!

In comparison with the conventional coating single-phase nano
crystal coating technology offers higher coating hardness and
heat resistance.
When machining hardened steels it can be seen that the
IMPACT MIRACLE coating offers a lower friction of coefficient
and as such prevents abnormal damage such as chipping.
FEATURES OF IMPACT MIRACLE COATING

Shingle phase nano coating
(Al,Ti,Si)N
(Al,Ti,Si)N
(Al,Ti)N
Hardness (HV)
3700
3200
2800
Oxidation Temperature (r)
1300
1100
840
100
80
80
0.48
0.53
0.58
1)
Adhesion (N)
2)
Wear Coefficient (800r)
1) Adhesion : Measured by critical load scratch test.

2) Coefficient of friction : Measured by ball-on-disk method.
(Counter gear : AISI D2 60HRC)
VC MIRACLE Coating (Al,Ti)N

MIRACLE coating for high speed milling.
Miracle coating is produced by adding Al to the existing TiN coating.
This coating layer consists of a compound solid solution of (Al,Ti)N.
It has succeeded in improving the heat resistance during cutting and coating hardness, and thus delivers high performance in high
hardness material machining and high speed dry cutting. It also has the high adhesion strength for the cemented carbide substrate,
and extends the tool life significantly compared to conventional products.
J004
(Al,Ti,Cr)N multilayer coating (MS Plus)

Suitable coating for a broad range of workpiece materials such
as carbon steel, alloy steel and hardened steel of approx. 50HRC.
Our original coating technology enables a multilayer of (Al,Ti)N and (Al,Cr)N. It allows machining of a
wide range of workpiece materials.
Properties of (Al,Ti,Cr)N multilayer coating (MS Plus)

(Al,Ti,Cr)N
multilayer
(Al,Ti)N
(Al,Cr )N
Hardness (HV)
3200
2800
3100
Oxidation Temperature (r)
1100
800
1100
Adhesion (N)
100
80
80
CRN CRN Coating

Specially designed for milling of copper electrode and copper alloy.
CRN coating has been developed for copper alloy milling. It has superior wear resistance and excellent adhesion strength by using
Miracle coating technology. The excellent anti adhesion properties needed for copper machining has been achieved due to its low
friction coefficient at high temperatures.
Newly developed DLC coating.

Hardness similar to that of CVD diamond coating achieved with high adhesion strength.
Mitsubishi Materials and NAGATA SEIKI have jointly developed a unique DLC coating that has substantially increased "adhesion
strength" compared to previous DLC coatings.
DFC Diamond Coating
SOLID END MILLS
DLC DLC Coating
Proprietary CVD diamond coating produces excellent wear resistance and smooth hole surface.
The newly developed CVD diamond coated carbide material achieves outstanding abrasion resistance and smoothness due to a
proprietary fine multilayer diamond crystal control technology.
DF Diamond Coating
Diamond coating for non-ferrous and new non-metal materials.
Owing to Mitsubishis unique plasma chemical vapor deposition (CVD) coating technology, great combination of coating hardness
similar to that of natural diamond has been combined with a good adhesion to carbide substrates.
DF end mill series suitable for graphite machining.
V VIOLET Coating
(Al,Ti)N coating, excellent adhesion strength for HSS tools.
Violet coating is the name of the technology of successfully applying a Miracle type coating to HSS substrate tools. The newly developed technology of applying (Al,Ti)N coating at the low temperatures required for HSS substrates, means that Violet coating has the
same level of adhesion strength as Miracle coating. Additionally high film hardness and excellent oxidation resistance properties have
also been realised.
J005
SOLID END MILLS
y HOW TO USE TOOL NAVI

3 steps provide the correct tool and cutting data.
STEP1
Chose work material, end mill type and cutting length.
INDEX
Type
Carbon steel
Alloy steel
Cast iron
Work material
Square end mill
Short (ap1.5xD) .........................................................................................

Medium (ap3xD) ........................................................................................
Long (ap5xD).............................................................................................
Long neck (ap30xD) .................................................................................
J008
J008
J009
J009
Page
Radius end mills
Short / Medium (ap3xD) ........................................................................... J010

Long neck (ap50xD) ................................................................................. J010
Ball nose end mills
Short / Medium (ap3xD) ........................................................................... J011

Long neck (ap70xD) ................................................................................. J012
Hardened steel
STEP2
Square end mill
Short (ap1.5xD) ......................................................................................... J013

Medium (ap3xD) ........................................................................................ J013
Long neck (ap12xD) ................................................................................. J013
Chose end mill.
Page
Finish / Rough
ap
Flutes
End mills
Neck length
Size range
Product name
Coating
SOLID END MILLS
Work materials
Recommendation
*1
Square end mill
SOLID END MILLS
Short (ap1.5xD)
Recommended end mill
MS
MS2ES
*2
DC312
0.5
1xDC
J065
DC0.1
12
1.5xDC
J048
DC312
0.5
1xDC
J110
1st recommendation
2nd recommendation
DC314
0.5
1xDC
J141
Page
*1 Finish
*2 Rough
30
MS
MS2SS
30
DC<3
DC3
MS
MS3ES
30
MS
MS4EC
ILLS
30
Chose size and cutting condition.
Austenitic
Stainless Steel
Titanium Alloy,
CARBIDE
DC
h6
APMX
0
- 0.008
Type2
Type3
Work
material
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
7
8
10
12
10000
7500
6000
5000
4500
4000
3200
2700
600
600
600
600
560
520
450
410
7000
5200
4200
3500
3000
2800
2200
1900
400
400
400
400
360
350
300
270
6000
4500
3600
3000
2700
2400
1900
1600
300
300
300
300
280
260
230
210
5000
4000
3200
2700
2300
2000
1600
1300
120
120
120
120
110
110
100
100
Depth of
cut
3
3.5
4
5
5
6
6
6
6
6
6
6
6
35
35
35
35
35
35
35
35
35
35
35
35
35
4
4
4
5
6
5
6
7
7
8
7
10
10
2
2
2
2
2
2
2
2
2
2
2
2
2
Order Number
DC
APMX
LF
DCON
Stock
MS2ESD0300L45S04
MS2ESD0350L45S04
MS2ESD0400L45S04
MS2ESD0500L45S06
MS2ESD0600L45S06
MS2ESD0700L45S07
MS2ESD0800L45S07
MS2ESD0800L45S08
MS2ESD1000L45S07
MS2ESD1000L45S10
MS2ESD1200L45S10
3
3.5
4
5
6
7
8
8
10
10
12
3
3.5
4
5
6
7
8
8
10
10
12
45
45
45
45
45
45
45
45
45
45
45
4
4
4
6
6
7
7
8
7
10
10
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
Overall length 45mm
1
1
2
2
1
3
2
2
3
2
3
2
3
a
a
<0.2DC
a
a
a
a
a
a
a
a
a
DC
<0.05DC
<0.2DC
<1DC
DC
<0.1DC
DC:Dia.
Unit : mm
<1DC
1) When cutting austenitic stainless steels, the use of water-soluble cutting fluid is effective.
2) If the depth of cut is shallow, the revolution and feed rate can be increased.
3) When drilling, please set the feed rate at 1/3 or below the values above.
4) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and
feed rate proportionately.
SOLID END MILLS
3
3.5
4
5
5
6
6
7
8
8
10
10
12
Stock
No. of
Flutes
MS2ESD0300L35S04
MS2ESD0350L35S04
MS2ESD0400L35S04
MS2ESD0500L35S05
MS2ESD0500L35S06
MS2ESD0600L35S05
MS2ESD0600L35S06
MS2ESD0700L35S07
MS2ESD0800L35S07
MS2ESD0800L35S08
MS2ESD1000L35S07
MS2ESD1000L35S10
MS2ESD1200L35S10
Type
AISI H13
Revolution
(min-1)
TAPER
DCON
Hardened steel (45 55HRC)
AISI 304, AISI 306, Ti-6Al-4V
Feed rate
(mm/min)
SOLID END MILLS
LF
No. of
Flutes
Unit : mm
APMX
Austenitic stainless steel,

Titanium alloy
Revolution
(min-1)
0
- 0.009
DC
AISI H13, AISI W1-10, AISI P21
Feed rate
(mm/min)
a 2 flute end mill.
Order Number
Alloy steel, Tool steel,

Pre-hardened steel
AISI 1050, AISI No 35 B, AISI P20

Revolution
(min-1)
LF
Overall length 35mm
Carbon steel, Cast iron,

Alloy steel ( 30HRC)
Dia.
DC (mm)
LF
DC
0
- 0.020
Type1
LF
DC
APMX
3 < DC < 12
MS2ES
End mill, 2 flute, For small automatic lathes
15
APMX
4<DCON<6 7<DCON<10
CARBIDE
Aluminium Alloy
DCON(h6)
30
Copper Alloy
SQUARE
MS
UWC
Hardened Steel
(>55HRC)
DCON(h6)
Hardened Steel
( < 55HRC)
DCON(h6)
Type
1
1
2
1
2
2
3
2
3
2
3
J065
J006
Cutting conditions
MSTAR END MILLS
MS2ES
(<30HRC)
( < 45HRC)
BALL
Size
RADIUS
STEP3
J066
INDEX
Carbon steel
Alloy steel
Cast iron
Square end mill
Short (ap1.5xDC) ...................................................................................... J008

Medium (ap3xDC) ..................................................................................... J008
Long (ap5xDC) .......................................................................................... J009
Long neck (ap30xDC) ............................................................................... J009
Radius end mills
Short / Medium (ap3xDC) ......................................................................... J010

Long neck (ap50xDC) ............................................................................... J010
Ball nose end mills

Long neck (ap70xDC) ............................................................................... J012
Hardened steel
Square end mill
Short (ap1.5xDC) ...................................................................................... J013

Medium (ap3xDC) ..................................................................................... J013
Long neck (ap12xDC) ............................................................................... J013
Radius end mills

Long neck (ap50xDC) ............................................................................... J014
Ball nose end mills

Long neck (ap70xDC) ............................................................................... J015
Ti alloy
Heat resistant alloys
M
S
Square end mill
Short (ap1.5xDC) ...................................................................................... J016

Medium (ap3xDC) ..................................................................................... J016
Long (ap5xDC) .......................................................................................... J017
Long neck (ap30xDC) ............................................................................... J018
Radius end mills

Long neck (ap50xDC) ............................................................................... J019
Ball nose end mills

Long neck (ap20xDC) ............................................................................... J019
Copper alloy
Aluminium alloy
SOLID END MILLS
Austenitic Stainless steel
Square end mill
Short (ap1.5xDC) ...................................................................................... J020

Medium (ap3xDC) ..................................................................................... J020
Long (ap5xDC) .......................................................................................... J020
Long neck (ap16xDC) ............................................................................... J021
Radius end mills

Long neck (ap30xDC) ............................................................................... J021
Ball nose end mills

Long neck (ap50xDC) ............................................................................... J022
Graphite
FRP
Square end mill
Long (ap5xDC) .......................................................................................... J022

Long neck (ap10xDC) ............................................................................... J023
Radius end mills
Long neck (ap30xDC) ............................................................................... J023
Ball nose end mills

Long neck (ap50xDC) ............................................................................... J023
: Depth of Cut
* ap
DC : Cutting Diameter
*
J007
0.5
1xDC
J065
DC0.1
12
1.5xDC
J048
DC312
0.5
1xDC
J110
DC314
0.5
1xDC
J141
DC112
1.5xDC
J132
DC320
1.5xDC
J126
DC0.2
20
2xDC
J049
DC0.1
12
3xDC
J054
DC120
1.6
2.5xDC
J108
ap
Work materials
Page
Flutes
End mills
Finish / Rough
Neck length
DC312
Size range
Product name
Coating
SOLID END MILLS
P
Square end mill
Short (ap1.5xDC)
MS2ES
MS
30
MS2SS
MS
30
DC<3
MS3ES
DC3
MS
30
MS4EC
MS
SOLID END MILLS
30
MS4SC
MS
30
MSSHD
MS
45
Medium (ap3xDC)
MS2MS
MS
30
DC<3
MS2JS
MS
30
DC<3
MSMHZD
MS
45
: Depth of Cut
* ap
*
J008
DC3
DC3
DC<3
DC3
Finish / Rough
DC225
2
3.1xDC
J127
DC520
2.8
3.5xDC
J199
DC120
1.6
2.5xDC
J112
DC225
2
2.8xDC
J151
DC320
1.8
2.2xDC
J180
DC220
2.8
4xDC
J130
DC0.2
12
4xDC
J056
DC112
4xDC
J135
DC220
3.3
4xDC
J155
DC0.2
6
1.3
2.5
1.6xDC 30xDC
J058
Work materials
Page
Flutes
MS
ap
Neck length
Coating
MSMHD
End mills
Size range
Product name
45
VFMFPR
VF
30
VQMHZV
VQ
42
43.5
45
VQMHV
VQ
VQSVR
VQ
43
44
45
DC<8
43
45
DC8
DC<8
DC8
Long (ap5xDC)
MSJHD
MS
45
MS2LS
MS
SOLID END MILLS
37
40
30
MS4JC
MS
30
DC<3
VQJHV
VQ
38
40
DC6
DC3
DC<3
DC3
37.5
40
DC>6
Long neck (ap30xDC)
MS2XL
MS
30
DC<0.4 DC0.4
J009
Work materials
Page
Finish / Rough
Flutes
ap
Neck length
End mills
Size range
Product name
Coating
SOLID END MILLS
P
Square end mill
Long neck (ap30xDC)
MS2XL6
MS
DC0.3
2.5
1.5
2.5
2.7xDC 5xDC
DC110
1xDC
J062
2.6
16.2xDC
J137
DC0.1
3
1.5
2.5
1.7xDC 12.5xDC
J071
DC0.2
1.0
1.5
2.5
1.67xDC 6xDC
3
4
J157
DC220
2
2.8xDC
J311
DC112
2xDC
J287
DC320
1.9
2.8xDC
J308
DC220
2
2.8xDC
J328
DC16
1xDC
25xDC
J290
30
MS4XL
MS
30
VF2XL
VF
30
DC<3
SOLID END MILLS
VQXL
VQ
DC=3
35
DC0.3 DC0.4
Radius end mills

Short / Medium (ap3xDC)
MSMHDRB
MS
45
MS2MRB
MS
30
DC<3
MS4MRB
DC3
MS
30
VQMHVRB
VQ
37
40
Long neck (ap50xDC)
MS2XLRB
MS
30
DC<3
J010
*
*
DC3
ap : Depth of Cut
PRFRAD : Ball nose end mill radius
Work materials
Page
Finish / Rough
Flutes
VF
ap
Neck length
Coating
VFHVRB
End mills
Size range
Product name
DC116
1
2.6
1.6xDC 50xDC
J315
DC0.6
12
1xDC
2.6
13.3xDC
2
4
J292
DC0.5
2
0.6xDC
36xDC
J302
PRFRAD 1.5
0.16
1.7xDC
J217
PRFRAD 1.8
0.256
3xDC
J219
PRFRAD
1xDC
0.16
J205
PRFRAD 1.5
0.16
1.7xDC
J206
PRFRAD 1.8
0.256
3xDC
J207
PRFRAD
12xDC
0.510
J232
PRFRAD
12xDC
0.510
J233
43
45
VCPSRB
[High precision]
VC
30
DC1.5 DC2
CBN2XLRB
CBN
Ball nose end mills

MS2SB
MS
MS2MB
MS
30
MP2SSB
SOLID END MILLS
30
30
MP2SB
30
MP2MB
30
VF2SDB
VF
30
VF2SDBL
VF
30
J011
PRFRAD
1.5xDC
16
J283
PRFRAD
12xDC
0.026
J246
PRFRAD
1xDC
0.13
2
20xDC
J221
PRFRAD 0.7
0.053
1xDC
1.2
20xDC
J209
PRFRAD
0.8xDC
0.13
2.5
20xDC
J237
PRFRAD
0.8xDC
0.21
2.5
12xDC
J236
6.6
PRFRAD 0.6
0.42.5 0.9xDC 70xDC
J271
J227
J267
ap
Work materials
Page
Flutes
Finish / Rough
Neck length
End mills
Size range
Product name
Coating
SOLID END MILLS
P
Ball nose end mills
VQ4SVB
VQ
45
VC2PSBP
[High precision]
VC
30
PRFRAD<0.5 PRFRAD0.5 PRFRAD<0.5 PRFRAD0.5
Long neck (ap70xDC)
MS2XLB
MS
30
SOLID END MILLS
MP2XLB
30
VF2XLB
VF
30
VF2XLBS
VF
30
VF3XB
VF
30
VF2WB
VF
PRFRAD
220
13
CBN2XLB
CBN
0.85
PRFRAD 0.6
0.21
0.8xDC 4xDC
0
: Depth of Cut
* ap
* PRFRAD : Ball nose end mill radius
*
J012
23xDC
1.5xDC
J048
DC112
2xDC
4
6
J184
DC125
2
3.5xDC
4
6
J185
DC0.5
6
2.5xDC
J069
DC620
2.5xDC
J145
DC0.1
3
1.5
2.5
1.7xDC 12.5xDC
J071
DC312
1xDC
J350
DC320
2.2
3.3xDC
J351
ap
Work materials
Page
Flutes
End mills
Finish / Rough
Neck length
DC0.1
12
Size range
Coating
Product name
H
Square end mill
Short (ap1.5xDC)
MS2SS
MS
30
DC<3
DC3
Medium (ap3xDC)
VFMD
VF2MV
VF
30
45
DC<3
DC3
30
45
DC<3
DC3
VF
DC<3
DC<3
VF
DC3
DC3
32.5
37.5
VF4MV
VF
35
38
SOLID END MILLS
VFSD
Long neck (ap12xDC)
VF2XL
VF
30
DC<3
DC=3
Radius end mills

VFSDRB
VF
45
VFMDRB
VF
45
J013
Work materials
Page
Finish / Rough
Flutes
ap
Neck length
End mills
Size range
Product name
Coating
SOLID END MILLS
H
Radius end mills
Long neck (ap50xDC)
VFHVRB
VF
DC116
1
2.6
1.6xDC 50xDC
J315
DC0.6
12
1xDC
2.6
13.3xDC
2
4
J292
DC312
0.06DC
3DC
4
6
J314
DC0.5
2
0.6xDC
36xDC
J302
PRFRAD
1xDC
0.56
J228
PRFRAD
12xDC
0.110
J229
PRFRAD
1xDC
0.16
J205
PRFRAD 1.5
0.16
1.7xDC
J206
PRFRAD 1.8
0.256
3xDC
J207
43
45
VCPSRB
[High precision]
VC
30
DC1.5 DC2
NEW
VFFDRB
VF
40
DC6
CBN2XLRB
DC8
CBN
SOLID END MILLS
Ball nose end mills

VF2SSB
VF
30
VF2SB
VF
30
MP2SSB
30
MP2SB
30
MP2MB
30
: Depth of Cut
* ap
*
J014
Finish / Rough
PRFRAD
12xDC
0.510
J232
PRFRAD
12xDC
0.510
J233
PRFRAD 1.8
0.56
3xDC
J281
PRFRAD
12xDC
0.026
J246
PRFRAD
0.8xDC
0.13
2.5
20xDC
J237
PRFRAD
0.8xDC
0.21
2.5
12xDC
J236
PRFRAD 0.7
0.053
1xDC
1.2
20xDC
J209
PRFRAD
0.6
6.6
0.4
0.9xDC 70xDC
2.5
J271
0.85
PRFRAD 0.6
0.21
0.8xDC 4xDC
J267
ap
Work materials
Page
Flutes
VF
Neck length
Coating
VF2SDB
End mills
Size range
Product name
30
VF2SDBL
VF
30
VF4MB
VF
30
VC2PSBP
[High precision]
VC
30
VF2XLB
VF
30
VF2XLBS
VF
30
MP2XLB
SOLID END MILLS
Long neck (ap70xDC)
30
VF3XB
VF
30
CBN2XLB
CBN
J015
DC320
1.5xDC
J126
DC312
0.5
1xDC
J065
DC225
2
3.1xDC
J127
DC120
1.6
2.5xDC
J108
DC120
1.6
2.5xDC
J112
DC616
1.9
2.4xDC
J118
DC225
2
2.8xDC
J151
DC320
1.8
2.2xDC
J180
Work materials
Page
Flutes
Finish / Rough
ap
Neck length
End mills
Size range
Product name
Coating
SOLID END MILLS
M
S
Square end mill
Short (ap1.5xDC)
MSSHD
MS
45
MS2ES
MS
30
Medium (ap3xDC)
MSMHD
MS
SOLID END MILLS
45
MSMHZD
MS
45
VQMHZV
VQ
42
43.5
45
VQMHZVOH
VQ
42
43.5
45
VQMHV
VQ
37
40
VQSVR
VQ
43
44
45
DC<8
*
*
J016
ap : Depth of Cut
43
45
DC8
DC<8
DC8
Finish / Rough
DC16,
DC20
2.2xDC
J150
DC620
1.9
2.4xDC
J183
DC10
20
1.9
2.2xDC
J187
DC16,
DC20
1.9
2xDC
J190
DC16,
DC20
1.9
2.1xDC
J201
DC16,
DC20
1.9
2.1xDC
J204
DC520
2.8
3.5xDC
J199
DC220
3.3
4xDC
J155
DC220
2.8
4xDC
J130
Work materials
Page
Flutes
VF
ap
Neck length
Coating
VFMHVCH
End mills
Size range
Product name
42
45
VF6MHV
VF
43.5
45
VF6MHVCH
VF
43.5
45
VF8MHVCH
VF
44
45
VFSFPRCH
VF
VF6SVRCH
VF
28.5
30
VFMFPR
VF
SOLID END MILLS
30
30
Long (ap5xDC)
VQJHV
VQ
38
40
DC6
MSJHD
MS
37.5
40
DC>6
45
J017
Work materials
Page
Finish / Rough
Flutes
ap
Neck length
End mills
Size range
Product name
Coating
SOLID END MILLS
M
S
Square end mill
Long neck (ap30xDC)
VQXL
VQ
35
DC0.2
1.0
1.5
2.5
1.67xDC 6xDC
3
4
J157
DC0.2
6
1.3
2.5
1.6xDC 30xDC
J058
DC0.3
2.5
1.5
2.5
2.7xDC 5xDC
J062
DC220
2
2.8xDC
J311
DC220
2
2.8xDC
J328
DC616
2.2
2.4xDC
J333
DC16
20
2.2
2.3xDC
J327
DC620
1.9
2.4xDC
J348
DC0.3 DC0.4
MS2XL
MS
30
DC<0.4 DC0.4
MS2XL6
MS
30
SOLID END MILLS
Radius end mills

MSMHDRB
MS
45
VQMHVRB
VQ
37
40
VQMHVRBF
VQ
37
40
VFMHVRBCH
VF
42
45
VF6MHVRB
VF
43.5
45
: Depth of Cut
* ap
*
J018
Finish / Rough
DC10
20
1.9
2.2xDC
J353
DC16,
DC20
1.9
2xDC
J354
DC116
1
2.6
1.6xDC 50xDC
J315
Work materials
Page
Flutes
VF6MHVRBCH VF
ap
Neck length
End mills
Size range
Coating
Product name
43.5
45
VF8MHVRBCH VF
44
45
Long neck (ap50xDC)
VFHVRB
VF
43
45
Ball nose end mills

VQ4SVB
VQ
PRFRAD
1.5xDC
16
J283
PRFRAD 0.7
0.053
1xDC
1.2
20xDC
J209
PRFRAD
220
13
23xDC
J227
Long neck (ap20xDC)
MP2XLB
30
VF2WB
VF
SOLID END MILLS
45
J019
DC10
26
0.8
1.3xDC
J124
DC320
0.9
2xDC
J102
DC10
25
1.1
1.3xDC
J193
DC0.2
12
2
3.2xDC
J081
DC325
1.5
3xDC
J104
DC325
1.8
2.8xDC
J195
DC312
2.5
4xDC
J166
DC312
34xDC
J167
Work materials
Page
Flutes
Finish / Rough
ap
Neck length
End mills
Size range
Product name
Coating
SOLID END MILLS
N
Square end mill
Short (ap1.5xDC)
C3SA
37.5
C2SA
37.5
CSRA
37.5
Medium (ap3xDC)
SOLID END MILLS
CRN2MS
CRN
30
DC<3
C2MHA
DC3
55
CMRA
37.5
Long (ap5xDC)
CRN4JC
CRN
30
DF4JC
DF
30
: Depth of Cut
* ap
*
J020
Work materials
Page
Finish / Rough
Flutes
ap
Neck length
End mills
Size range
Coating
Product name
Long neck (ap16xDC)
CRN2XL
CRN
30
DC<3
DF4XL
DF
DC0.2
6
1.5
2.5
1.7xDC 16xDC
J083
DC112
1.5xDC
2.5
10.6xDC
J168
DC612
2.2
2.4xDC
J298
DC12
25
0.8
1.3xDC
J304
DC10
25
1.1
1.3xDC
J306
DC0.5
6
1.5
5
1.6xDC 13xDC
J300
DC0.5
12
1.3
3.3
1.5xDC 30xDC
2
4
J345
DC3
30
DC<3
DC3
Radius end mills

CRN2MRB
CRN
30
C3SARB
CSRARB
37.5
Long neck (ap30xDC)
CRN2XLRB
CRN
30
DC<3
DFPSRB
SOLID END MILLS
37.5
DC3
DF
30
DC1.5 DC2
J021
PRFRAD 1.8
0.26
3xDC
J254
PRFRAD 4.6
36
5xDC
J260
PRFRAD
1xDC
0.13
2.5
20xDC
J256
2.5
PRFRAD 1.2
0.22
1.5xDC 40xDC
J261
20
50xDC
J278
ap
Work materials
Page
Flutes
Finish / Rough
Neck length
End mills
Size range
Product name
Coating
SOLID END MILLS
N
Ball nose end mills
CRN2MB
CRN
30
DF2MB
DF
30
Long neck (ap50xDC)
CRN2XLB
CRN
30
SOLID END MILLS
DF2XLB
DF
30
DF3XB
PRFRAD
1.5xDC
0.52
DF
30
G
Square end mill
Long (ap5xDC)
DF4JC
DF
DC312
34xDC
J167
DC612
2.5
3.8xDC
J171
DC612
2.5
3.8xDC
10
12
J172
30
DFC4JC
DFC
10
DFCJRT
DFC
: Depth of Cut
* ap
*
J022
DC112
1.5xDC
2.5
10.6xDC
J168
DC0.5
12
1.3
3.3
1.5xDC 30xDC
2
4
J345
J260
2.5
PRFRAD 1.2
0.22
1.5xDC 40xDC
J261
20
50xDC
J278
Work materials
Page
Flutes
Finish / Rough
ap
Neck length
End mills
Size range
Coating
Product name
Long neck (ap10xDC)
DF4XL
DF
30
DC<3
DC3
Radius end mills

Long neck (ap30xDC)
DFPSRB
DF
30
DC1.5 DC2
Ball nose end mills

DF2MB
PRFRAD 4.6
36
5xDC
DF
30
DF2XLB
DF
30
DF3XB
PRFRAD
1.5xDC
0.52
DF
SOLID END MILLS
Long neck (ap50xDC)
30
J023
SOLID END MILLS
CARBIDE (By Series)

Page Number
Aluminium Alloy
Copper Alloy
Titanium Alloy, Heat Resistant Alloy
M S
Austenitic Stainless Steel
Hardened Steel(55HRC-)
H
Hardened Steel(-55HRC)
Tool steel, Pre-Hardened Steel, Hardened Steel
Shape
Carbon Steel, Alloy Steel, Cast Iron
Product
Code
Size Range
Coating
No. of Flutes
Type
Applications,
Features
Work Material
P
Cutting
Conditions
END MILLS SELECTION CHART
Dimensions
CARBIDE
MS PLUS END MILL SERIES

MP2SSB
BALL
MP2SB
Ball nose, Short cut length, 2 flute
2
MP2MB
Ball nose, Medium cutting length, 2 flute
LONG
NECK
BALL
General Use
Ball nose, Short cut length, 2 flute, Short shank
MP2XLB
End mill, Short cut length, 2 flute, Long neck
PRFRAD
e e e
0.16
u u u
J205 J208
PRFRAD
e e u
0.16
u u u
J206 J208
PRFRAD
e e u
0.256
u u u
J207 J208
PRFRAD
e e u
0.053
u u u
J209 J214
DC
0.112
e e u
u u
J048 J051
DC
0.220
e e u
u u
J049 J051
DC
112
e e u
u u
J052 J053
DC
0.112
e e u
u u
J054 J055
DC
0.212
e e u
u u
J056 J057
DC
112
e e u
u u
J132 J134
DC
120
e e u
u u
J133 J134
DC
112
e e u
u u
J135 J136
DC
120
e e u
e u
J108 J109
DC
320
e e u
e u
J126 J129
DC
225
e e u
e e
J127 J129
DC
220
e e u
e e
J130 J131
DC
220
e e u
e e
J311 J313
MSTAR END MILL SERIES

MS2SS
MS2MS
End mill, Medium cut length, 2 flute
MS2MD
General Use
MS2JS
End mill, Semi long cut length, 2 flute
MS2LS
End mill, Long cut length, 2 flute
SQUARE
SOLID END MILLS
End mill, Medium cut length, 2 flute, Strong geometry type
MS4SC
MS4MC
MS4JC
General Use,
For Key Way
Slotting
MSMHZD
Slotting, Medium cut length, 3 flute
High power, Short cut length, 4 flute

MSMHD
High power, Medium cut length, 4 flute
4
MSJHD
High power, Semi long cut length, 4 flute
RADIUS
For high feed cutting
MSSHD
MSMHDRB
: Cutting Diameter
* DC
*
J024
High power, Corner radius, Medium cut length, 4 flute
CARBIDE
Ball nose end mill, Short cut length, 2 flute

MS2MB
Ball nose end mill, Medium cut length, 2 flute
LONG NECK SQUARE

LONG NECK LONG
TAPER
TAPER CORNER NECK
BALL
RADIUS
BALL
RADIUS
For Deep Slotting

For Rib Milling
MS2XL
MS2XL6
End mill, Short cut length, 2 flute, 6mm shank
MS4XL
MS2XLB
Ball nose end mill, Short cut length, 2 flute, Long neck
2
MS2XLRB
Corner radius end mill, Short cut length, 2 flute, Long neck
MS4LT
Taper end mill, Long cut length, 4 flute
4
MS4LTB
Ball nose, 4 flute, Taper, For rib milling
MS2MRB
Corner radius end mill, Medium cut length, 2 flute
MS4MRB
TAPER
TAPER
BALL
MS2MT
Taper end mill, Medium cut length, 2 flute
MS2MTB
Ball nose taper end mill, Medium cut length, 2 flute
MS2ES
SQUARE
For Small
Automatic Lathes
For Angled Face

Machining
MS3ES
MS4EC
Page Number
Cutting
Conditions
Dimensions
Aluminium Alloy
Copper Alloy
M S
PRFRAD
e e u
0.16
u u
J217 J220
PRFRAD
e e u
0.256
u u
J219 J220
DC
0.26
e e u
u u
J058 J061
DC
e e u
0.32.5
u u
J062 J064
DC
110
e e u
u u
J137 J140
PRFRAD
e e u
0.13
u u
J221 J226
DC
1 6
e e u
u u
J290 J291
DC
0.23
e e u
J360 J366
PRFRAD
e e u
0.31
u u
J369 J372
DC
112
e e u
u u
J287 J289
DC
320
e e u
u u
J308 J310
DC
0.210
e e u
u u
J355 J359
PRFRAD
e e u
0.21.5
u u
J367 J368
DC
312
e e u
u u
J065 J066
DC
312
e e u
u u
J110 J111
DC
314
e e u
u u
J141 J142
SOLID END MILLS
MS2SB
For Corner
Radius
Shape
Size Range
Coating
No. of Flutes
Type
Product
Code
BALL
For Profiling
Applications,
Features
Work Material
P
J025
SOLID END MILLS
CARBIDE (By Series)

Page Number
Aluminium Alloy
Copper Alloy
M S
H
Shape
Product
Code
Size Range
Coating
No. of Flutes
Type
Applications,
Features
Work Material
P
Cutting
Conditions
Dimensions
CARBIDE
SMART MIRACLE END MILL SERIES

NEW
VQ
VQXL
3
4
NEW
VQ
VQSVR
SQUARE
VQMHZV
End mill, Medium cutting length, 3 flute for drilling and slotting
3
VQ
VQMHZVOH
VQ
VQMHV
End mill, Medium cutting length, 4 flute, Irregular helix flutes
NEW
VQ
VQJHV
End mill, Medium cut length, 4 flute, Irregular helix flutes
VQ
VQ4SVB
RADIUS
VQ
VQMHVRB
Corner radius end mill, Medium cutting length, 4 flute, Irregular helix flutes
VQ
VQMHVRBF
Corner radius end mill, Medium cutting length, 4 flute, Irregular helix flutes (for finishing)
WIDE
BALL
VF VF2WB
Wide ball nose, Medium cut length, 2 flute
VF VF2MD
VF VF2MV
SQUARE
For Machining of Hardened Steels
End mill, Medium cut length, 2 flute, For hardened materials
VF VF4MD
4
VF VF4MV
VF VFSD
End mill, Short cut length, For hardened materials
4
6
VF VFMD
BALL
End mill, Medium cut length, For hardened materials
VF VF2SSB
: Cutting Diameter
* DC
*
J026
e u
e e u
J157 J158
DC
320
e u
e e u
J180 J181
DC
120
e u
e e u
J112 J114
DC
616
e u
e e u
J118 J119
DC
225
e u
e e u
J151 J152
DC
220
e u
e e u
J155 J156
PRFRAD
u u
1 6
e e u
J283 J284
DC
220
e u
u e u
J328 J330
DC
616
u u
u e
J333 J334
e e
J227 J227
IMPACT MIRACLE END MILL SERIES

For Profiling
of Special
Geometry
SOLID END MILLS
VQ
End mill, Medium cutting length, 3 flute for drilling and slotting with internal through coolant holes
BALL
For Difficult-to-cut Materials
Roughing end mill, Short cut length, 34 flute, Irregular helix flutes
DC
0.21
PRFRAD
u e u
1 3
DC
0.56
u e e e
J067 J068
DC
0.56
u e e e
J069 J070
DC
120
u e e e
J143 J144
DC
620
u e e e
J145 J145
DC
112
u e e e
J184 J186
DC
125
u e e e
J185 J186
PRFRAD
u e e e u u
0.56
J228 J231
CARBIDE
VF VF4MB
4
6
RADIUS
For Machining
of Hardened Steels
Ball nose, Medium cut length, 4 flute

NEW
VF VFFDRB
Multi-task corner radius end mill for impact miracle high speed cutting
VF VFSDRB
IMPACT MIRACLE Corner radius end mill, 6 flute (S)
6
VF VFMDRB
3
4
VF VFSFPR
VF VFMFPR
Roughing end mill, Short cut length, 34 flute
Roughing end mill, Medium cut length, 4 flute
LONG
NECK
SQUARE
LONG NECK
BALL
For Machining
of Hardened
Steels
TAPER
NECK
BALL
For Deep Slotting

of Hardened Steels
ROUGHING
Corner radius, Medium cut length, 6 flute, For hardened materials
VF VF2XL
End mill, 2 flute, Long neck
VF VF2XLBS
Ball nose, Medium cut length, 2 flute, Short shank
VF VF2XLB
IMPACT MIRACLE, Ball nose, 2 flute, Long neck
VF VF3XB
Ball nose, Medium cut length, 3 flute, Taper neck
Page Number
Cutting
Conditions
Aluminium Alloy
Dimensions
Copper Alloy
M S
PRFRAD
u e e e u u
0.110
J229 J231
PRFRAD
0.56
J281 J282
e e e u u
DC
312
u u e e
J314 J314
DC
312
u e e e
J350 J352
DC
320
u e e e
J351 J352
DC
320
e e u
e e
J197 J198
DC
520
e e u
e e
J199 J200
DC
0.13
u e e e
J071 J073
PRFRAD
u e e e
0.21
J236 J242
PRFRAD
u e e e
0.13
J237 J242
PRFRAD
u e e e u u
0.42.5
J271 J274
PRFRAD
u e e u
0.510
J232 J234
PRFRAD
u e e u
0.510
J233 J234
SOLID END MILLS
Ball nose, Short cut length, 2 flute, For hardened materials
Shape
Coating
VF VF2SB
Product
Code
Size Range
No. of Flutes
Type
2
BALL
Applications,
Features
Work Material
P
BALL
For high feed

cutting
IMPACT MIRACLE BALL NOSE HIGH POWER END MILL SERIES

VF VF2SDB
Ball nose, Short cut length, 2 flute, Strong geometry type
2
VF VF2SDBL
Ball nose, Short cut length, 2 flute, Strong geometry type, Long shank
R ADIUS
For High
Efficiency
Machining
IMPACT MIRACLE CORNER RADIUS END MILL SERIES FOR HIGH EFFICIENCY MACHINIG, IRREGULAR HELIX
VF VFHVRB
4 flute, Corner radius, Short cut length,Irregular helix flutes
DC
116
e e e e u u
J315 J317
VF VFMHV
SQUARE
IMPACT MIRACLE END MILL SERIES FOR DIFFICULT TO CUT MATERIALS, IRREGULAR HELIX
End mill, Medium cut length, Irregular helix flutes
4
VF VFJHV
End mill, Semi long cut length, Irregular helix flutes
VF VF6MHV
DC
220
u u u
e e
J146 J147
DC
220
u u u
e e
J148 J149
e e
J183 J183
DC
620
J027
SOLID END MILLS
CARBIDE (By Series)

Page Number
Aluminium Alloy
Copper Alloy
M S
H
Shape
Product
Code
Size Range
Coating
No. of Flutes
Type
Applications,
Features
Work Material
P
Cutting
Conditions
Dimensions
CARBIDE
BALL
RADIUS
IMPACT MIRACLE END MILL SERIES FOR DIFFICULT TO CUT MATERIALS, IRREGULAR HELIX
VF VF4SVB
Ball nose, Short cut length, 4 flute,Variable curve
4
VF VFMHVRB
Corner radius, Medium cut length, Irregular helix flutes
VF VF6MHVRB
Corner radius, Medium cut length, 6 flute, Irregular helix flutes
PRFRAD
u u
110
e e
J279 J280
DC
620
e u u
e e
J325 J326
DC
620
u u u
e e
J348 J349
DC
16,20
e e
J150 J150
DC
10,12
16,20
e e
J187 J187
DC
16,20
e e
J190 J190
DC
1620
e e
J327 J327
DC
10,12
16,20
e e
J353 J353
DC
16,20
e e
J354 J354
DC
16,20
e e
J201 J201
DC
16,20
e e
J204 J204
RADIUS
ROUGHING
SOLID END MILLS
SQUARE
COOL STAR END MILL SERIES
VF VFMHVCH
End mill, Medium cut length, 4 flute,

Irregular helix flutes, with multiple internal through coolant holes
VF VF6MHVCH

VF VF8MHVCH

VF VFMHVRBCH
Corner radius end mill, Medium cut length,

4 flute, Irregular helix flutes, with multiple internal through coolant holes
VF VF6MHVRBCH

VF VF8MHVRBCH

VF VFSFPRCH
Roughing end mill, Short cut length,

4 flute, with multiple internal through coolant holes
VF VF6SVRCH
Roughing end mill, Short cut length, 6 flute,

MIRACLE END MILL SERIES

DC
0.316
u e e
u u
J074 J075
DC
0.325
u e e
u u
J076 J078
DC
125
u e e
u u
J079 J080
DC
225
u e e u u u
J160 J161
DC
325
u e e u u u
J162 J163
PRFRAD
u e e u u u
1.5
MIRACLE ball nose high power end mill (M), 2 flute 12.5
J249 J250
VC VC2SS
End mill, Extra short cut length, 2 flute
VC2MS
SQUARE
General Use
2 VC
VC VC2JS
VC VC4MC
4
VC VC4JC
BALL
For high feed

cutting
2 VC
VC2MDB
: Cutting Diameter
* DC
J028 *
CARBIDE
Ball nose, Extra short cut length, 2 flute, Short shank
2
VC VC2MB
3 VC
VC3MB
2 VC
VCXB
Ball nose taper end mill, Medium cut length, Taper neck
VC VC4SRB
Corner radius end mill, Short cut length, 4 flute
4
VC VC4JRB
CHAMFERING ROUGHING
For
For
Chamfering Roughing
Corner radius end mill, Semi long cut length, 4 flute
3 VC
4
VCSFPR
2 VC
VC2C
Chamfer cutter, 2 flute
Page Number
Cutting
Conditions
Dimensions
Aluminium Alloy
Copper Alloy
M S
PRFRAD
u e e u u u
0.156
J243 J244
PRFRAD
u e e u u u
0.2
12.5
J248 J250
PRFRAD
u e e u u u
110
J276 J277
PRFRAD
u e e u u u
0.56
J251 J253
DC
412
u e e u u u
J335 J336
DC
320
u e u u u u
J337 J338
DC
320
e e u
J202 J203
DC
2 12
e e e u e e u u
e e
J377 J377
BALL
For Ultra high- For Highprecision Precision

Machining Machining
MIRACLE NOVA END MILL SERIES

VC VC2PSB
Ball nose end mill, Short cut length, 2 flute, High precision
2
VC VC2PSBP
MIRACLE ball nose ultra high-precision end mill(S), 2 flute
PRFRAD
e e e
0.056
u u
J245 J247
PRFRAD
e e e
0.026
u u
J246 J247
DC
0.612
e e e e u u
J292 J295
DC
216
e e e u
J339 J341
DC
0.53
u e e e
J164 J165
DC
625
u e e e
J188 J188
SOLID END MILLS
VC VC2ESB
Shape
Product
Code
Size Range
Coating
No. of Flutes
Type
RADIUS
For Corner
Radius
For High
For
Efficiency For Profiling
Deep Slotting Machining
TAPER
NECK
BALL
BALL
Applications,
Features
Work Material
P
RADIUS
For HighPrecision
Machining
MIRACLE ORBIT END MILL SERIES
2 VC
4
VCPSRB
Corner radius end mill, Short cut length, 24 flute, High precision
RADIUS
For High
Feed
Machining
MIRACLE CORNER RADIUS END MILL SERIES FOR HIGH FEED MACHINING
4 VC
VCHFRB
Corner radius, Short flute length, 4 flute, High feed machining
SQUARE
4 VC
6
VCMDSC
6 VC
VCLD
TAPER
BALL
BALL
For Angled
Face
Machining
For Machining
of Hardened Steels
MIRACLE END MILL SERIES FOR HIGH HARDNESS STEEL
VC VC4MB
4
VC VC4STB
Ball nose taper end mill, Short cut length, 4 flute
PRFRAD
u e e e u u
0.510
J285 J286
PRFRAD
u e e e u u
0.34
J373 J375
J029
SOLID END MILLS
CARBIDE (By Series)

Page Number
Aluminium Alloy
Copper Alloy
M S
H
Shape
Product
Code
Size Range
Coating
No. of Flutes
Type
Applications,
Features
Work Material
P
Cutting
Conditions
Dimensions
CARBIDE
SQUARE
3 VC
4
VCMH
6 VC
VC6MH
End mill, Medium cut length, 34 flute, High helix angle
8 VC
VC8MH
RADIUS
MIRACLE END MILL SERIES FOR DIFFICULT TO CUT MATERIALS
4 VC
VCMHDRB
Corner radius end mill, Medium cut length, 4 flute, High helix angle
DC
325
u e u
e e
J121 J122
DC
625
e e u
e e
J189 J189
DC
2025
e e u
e e
J191 J191
DC
225
u e e u e e
J342 J344
DC
216
e e
u u
J088 J090
DC
216
e e
u u
J089 J090
SQUARE
For Key Way

Slotting
END MILL SERIES FOR SLOTTING

SED2KPG
End mill, Medium cut length, 2 flute, + Tolerance
2
SED2KMG
LONG
BALL SQUARE NECK SQUARE
SQUARE
LONG
LONG NECK
CORNER RADIUS NECK
BALL
RADIUS
For Copper Electrodes
SOLID END MILLS
CRN END MILL SERIES

CRN CRN2MS
End mill, Medium cut length, 2 flute, For copper electrodes
2
CRN CRN2XL
End mill, Medium cut length, 2 flute, Long neck, For copper electrodes
4 CRN
CRN4JC
End mill, Semi long cut length, 4 flute, For copper electrodes
CRN CRN2MB
Ball nose, Medium cut length, 2 flute, For copper electrodes
CRN CRN2XLB
Ball nose, Medium cut length, 2 flute, Long neck, For copper electrodes
2
CRN CRN2MRB
Corner radius, Medium cut length, 2 flute, For copper electrodes
CRN CRN2XLRB
DC
0.212
e u
J081 J082
DC
0.26
e u
J083 J085
DC
312
e u
J166 J166
PRFRAD
0.26
e u
J254 J255
PRFRAD
0.13
e u
J256 J259
DC
612
e u
J298 J299
DC
0.56
e u
J300 J301
SQUARE WITH
SQUARE
CROSS-NICK
For CFRP
machining
DFC END MILL SERIES
DFC
DFC4JC
Diamond coating endmill, 4 flute
DFC
DFCJRT
: Cutting Diameter
* DC
*
J030
Diamond coating endmill with cross-nick
DC
612
J171 J171
CFRP : u
DC
612
J172 J172
CARBIDE
Page Number
Cutting
Conditions
Dimensions
Aluminium Alloy
Copper Alloy
M S
Shape
Product
Code
Size Range
Coating
No. of Flutes
Type
Applications,
Features
Work Material
P
DF DF4JC
End mill, Semi long cut length, 4 flute, For graphite
4
DF DF4XL
End mill, Long neck, 4 flute, For graphite
BALL
TAPER LONG
RADIUS NECK NECK
BALL BALL
For Graphite
LONG
NECK SQUARE
SQUARE
DF END MILL SERIES
DF DF2MB
Ball nose, Medium cut length, 2 flute, For graphite
2
DF DF2XLB
Ball nose, Medium cut length, 2 flute, Long neck, For graphite
DF DF3XB
Ball nose, Medium cut length, 3 flute, Taper neck, For graphite
2
4
DF DFPSRB
Corner radius end mill, Short cut length, 2 4 flute, High precision, For graphite
DC
312
J167 J167
DC
112
J168 J169
J260 J260
J261 J263
PRFRAD
0.52
J278 J278
DC
0.512
J345 J347
u e
J086 J087
PRFRAD
0.110
u e
J265 J266
DC
320
u e
J102 J103
DC
120
J098 J099
DC
120
J100 J101
DC
325
J104 J105
DC
1026
u e
J124 J125
DC
1225
u e
J304 J305
DC
1025
J193 J194
DC
325
J195 J196
DC
10 25
J306 J307
PRFRAD
3 6
PRFRAD
0.22
Graphite : e
GFRP : u
CFRP : u
DLC DLC2MA
Slot drill, Medium cut length, 2 flute
2
DLC DLC2MB
DC
120
GFRP : u
CFRP : u
ALIMASTER END MILL SERIES
C2SA
End mill, Short cut length, 2 flute, For aluminium alloy
SQUARE
C2MA
End mill, Medium cut length, 2 flute, For aluminium alloy
C2LA
End mill, Long cut length, 2 flute, For aluminium alloy
C2MHA
C3SA
ROUGHING
RADIUS
C3SARB
Corner radius, Short cut length, 3 flute, For aluminium alloy
CSRA
Roughing end mill, Short cut length, 3 flute, For aluminium alloy
CMRA
Roughing end mill, Medium cut length, 3 flute, For aluminium alloy
ROUGHING
RADIUS
For Machining of Aluminium Alloys
CSRARB
Corner radius roughing end mill,

Short cut length, 3 flute, For aluminium alloy
SOLID END MILLS
BALL SQUARE
For Machining
of Aluminium Alloys
DLC END MILL SERIES
J031
SOLID END MILLS
CARBIDE (By Series)

Page Number
Aluminium Alloy
Copper Alloy
M S
Shape
Product
Code
Size Range
Coating
No. of Flutes
Type
Applications,
Features
Work Material
P
Cutting
Conditions
Dimensions
CARBIDE
CARBIDE END MILL SERIES
C2SS
C2MS
2
C2JS
SQUARE
General Use
C2LS
C4MC
End mill, Medium cut length, 4 flute, Center cutting
C4JC
End mill, Semi long cut length, 4 flute, Center cutting
C4LC
BALL
C2MB
SEE2L
SQUARE
For
Profiling
High Helix
For Difficult- For Machining
to-cut
of Aluminium
Materials
Alloys
SOLID END MILLS
End mill, Long cut length, 4 flute, Center cutting
SEE4L
SEG4SA
CMH
End mill, Medium cut length,

4 flute, Irregular spiral helix angle, For aluminium alloy
DC
0.46
u u
u u u u
J091 J097
DC
120
u u
u u u u
J092 J097
DC
125
u u
u u u u
J095 J097
DC
120
u u
u u u u
J096 J097
DC
320
u u
u u u u
J173 J176
DC
325
u u
u u u u
J174 J176
DC
320
u u
u u u u
J175 J176
PRFRAD
e u
0.510
u u u u
J269 J270
DC
320
e u
u u u u
J106 J107
DC
325
e u
u u
J177 J178
u e
J179 J179
DC
625
DC
616
u e
u u
J123
LONG NECK LONG

CORNER NECK SQUARE
BALL
RADIUS
For Machining
of Hardened Steels
CBN END MILL SERIES
GBE
End mill, 1 flute, Brazed type (CBN)
CBN2XLB
Ball nose, Short cut length, 2 flute, Long neck
CBN2XLRB
: Cutting Diameter
* DC
*
J032
Corner radius end mill, Medium cut length, 2 flute, Long neck
DC
6 12
u e e
J192 J192
PRFRAD
u e e e
0.2 1
J267 J268
DC
0.5 2
J302 J303
u e e e
CARBIDE
Page Number
Cutting
Conditions
Aluminium Alloy
N
Copper Alloy
M S
Shape
Coating
Product
Code
Size Range
Applications,
Features
No. of Flutes
For Machining
of Hardened
Steels
Type
Work Material
P
Dimensions
CARBIDE(By Shape)
SQUARE
GBE
End mill, 1 flute, Brazed type (CBN)
MS2SS
MS2MS
MS2MD
End mill, Medium cut length, 2 flute, Strong geometry type
MS2JS
MS2LS
General Use
VC VC2SS
VC VC2MS
VC VC2JS
C2SS
C2MS
C2JS
C2LS
For Small
Automatic
Lathes
High
helix
For Key Way

Slotting

SED2KPG
SED2KMG
SEE2L
MS2ES
DC
6 12
J192 J192
u e e
DC
0.112
e e u
u u
J048 J051
DC
0.220
e e u
u u
J049 J051
DC
112
e e u
u u
J052 J053
DC
0.112
e e u
u u
J054 J055
DC
0.212
e e u
u u
J056 J057
DC
0.316
u e e
u u
J074 J075
DC
0.325
u e e
u u
J076 J078
DC
125
u e e
u u
J079 J080
DC
0.46
u u
u u u u
J091 J097
DC
120
u u
u u u u
J092 J097
DC
125
u u
u u u u
J095 J097
DC
120
u u
u u u u
J096 J097
DC
216
e e
u u
J088 J090
DC
216
e e
u u
J089 J090
DC
320
e u
u u u u
J106 J107
DC
312
e e u
u u
J065 J066
SOLID END MILLS
J033
SOLID END MILLS
END MILLS SELECTION CHART CARBIDE(By Shape)

Page Number
Cutting
Conditions
Aluminium Alloy
N
Copper Alloy
M S
Shape
Product
Code
Size Range
Coating
Applications,
Features
No. of Flutes
Type
Work Material
P
Dimensions
CARBIDE
SOLID END MILLS
For Copper
For Machining
Electrodes of Hardened Steels
SQUARE
VF VF2MD
VF VF2MV
CRN CRN2MS
DLC DLC2MA
C2SA
C2MA
C2LA
C2MHA
For Difficult-to-cut
Materials
For Small General Use,

Automatic For Key Way
Slotting
Lathes

MSMHZD
MS3ES
VQ
VQMHZV
VQ
VQMHZVOH
CMH
For Machining of
Aluminium Alloys
C3SA
3
4
Materials
NEW
VQ
VQXL
NEW
VQ
VQSVR
VC VCMH
* DC : Cutting Diameter
J034
DC
0.56
u e e e
J067 J068
DC
0.56
u e e e
J069 J070
DC
0.212
e u
J081 J082
u e
J086 J087
DC
320
u e
J102 J103
DC
120
J098 J099
DC
120
J100 J101
DC
325
J104 J105
DC
120
GFRP : u
CFRP : u
DC
120
e e u
e u
J108 J109
DC
312
e e u
u u
J110 J111
DC
120
e u
e e u
J112 J114
DC
616
e u
e e u
J118 J119
DC
616
u e
u u
DC
1026
u e
J123
J124 J125
DC
0.21
e u
e e u
J157 J158
DC
320
e u
e e u
J180 J181
DC
325
u e u
e e
J121 J122
CARBIDE
MS4MC
MS4JC
General Use
VC VC4MC
VC VC4JC
C4MC
C4JC
C4LC
High
helix
Materials

MSSHD
MSMHD
MSJHD
SEE4L
MS4EC
VF VF4MD
VF VF4MV
VQ
VQMHV
NEW
VQ
VQJHV
VF VFMHV
Page Number
Cutting
Conditions
Dimensions
Aluminium Alloy
N
Copper Alloy
M S
DC
112
e e u
u u
J132 J134
DC
120
e e u
u u
J133 J134
DC
112
e e u
u u
J135 J136
DC
225
u e e u u u
J160 J161
DC
325
u e e u u u
J162 J163
DC
320
u u
u u u u
J173 J176
DC
325
u u
u u u u
J174 J176
DC
320
u u
u u u u
J175 J176
DC
320
e e u
e e
J126 J129
DC
225
e e u
e e
J127 J129
DC
220
e e u
e e
J130 J131
DC
325
e u
u u
DC
314
e e u
u u
DC
120
u e e e
J143 J144
DC
620
u e e e
J145 J145
DC
225
e u
e e u
J151 J152
DC
220
e u
e e u
J155 J156
DC
220
u u u
e e
J146 J147
SOLID END MILLS
Shape
Size Range
Coating
Applications,
Features
No. of Flutes
Product
Code
MS4SC
For Small
For Machining
of Hardened Steels Automatic
Lathes
Type
Work Material
P
J177 J178
J141 J142
J035
SOLID END MILLS

Page Number
Cutting
Conditions
Aluminium Alloy
N
Copper Alloy
M S
Shape
Product
Code
Size Range
Coating
Applications,
Features
No. of Flutes
Type
Work Material
P
Dimensions
CARBIDE
For CFRP For Copper For Difficult-toFor

For Machining of
Aluminium Alloys Graphite machining Electrodes cut Materials
SQUARE
VF VFJHV
VF VFMHVCH
DC
DFC4JC
DF DF4JC
SEG4SA

4 flute, Irregular spiral helix angle, For aluminium alloy
For Machining
of Hardened Steels
SOLID END MILLS
VF VFSD
4
6
VF VFMD
VC VCMDSC
VC VCLD
VF VF6MHV
VF VF6MHVCH
e e
J150 J150
e u
DC
612
CFRP : u
DC
312
Graphite : e
GFRP : u
CFRP : u
DC
625
J171 J171
J167 J167
u e
J179 J179
u e e e
J184 J186
DC
125
u e e e
J185 J186
DC
0.53
u e e e
J164 J165
DC
625
u e e e
J188 J188
DC
620
DC
625
e e u
DC
J166 J166
DC
112

16,20
VC VC8MH
J036
J148 J149
e e
J183 J183
e e
J187 J187
e e
J189 J189
e e
J190 J190
e e
J191 J191
DC
: Cutting Diameter
* DC
*
e e
DC
312
10,12
Irregular helix flutes, with multiple internal through coolant holes 16,20
VC VC6MH
VF VF8MHVCH
u u u
EEnd mill, Medium cut length, 4 flute,

16,20
CRN CRN4JC
DFC
DC
220
DC
2025
e e u
CARBIDE
Page Number
Cutting
Conditions
Dimensions
Aluminium Alloy
N
Copper Alloy
M S
H
Shape
Product
Code
Size Range
Coating
Applications,
Features
No. of Flutes
Type
Work Material
P
For
For
For Deep For copper For Deep Slotting
Graphite Slotting electrodes of Hardened Steels Deep Slotting
LONG NECK SQUARE
MS2XL
MS2XL6
VF VF2XL
CRN CRN2XL
MS4XL
DF DF4XL
DC
0.26
e e u
u u
J058 J061
DC
e e u
0.32.5
u u
J062 J064
DC
0.13
J071 J073
u e e e
DC
0.26
DC
110
e u
e e u
J137 J140
u u
DC
112
Graphite : e
GFRP : u
CFRP : u
DC
612
CFRP : u
J083 J085
J168 J169
DFC
DFCJRT
J172 J172
2
4
For
For Rib
Angled Face
Milling Machining
TAPER
MS2MT
MS4LT
DC
0.210
e e u
u u
J355 J359
DC
0.23
e e u
J360 J366
PRFRAD
e e e
0.16
u u u
J205 J208
PRFRAD
e e u
0.16
u u u
J206 J208
PRFRAD
e e u
0.256
u u u
J207 J208
SOLID END MILLS
For CFRP
machining
SQUARE WITH CROSS-NICK
BALL
General Use
MP2SSB

MP2SB
MP2MB
VF VF2SDB
VF VF2SDBL
PRFRAD
u e e u
0.510
J232 J234
PRFRAD
u e e u
0.510
J233 J234
J037
SOLID END MILLS

Page Number
Cutting
Conditions
Aluminium Alloy
N
Copper Alloy
M S
Shape
Coating
VC VC2MDB
Product
Code
Size Range
Applications,
Features
For high
feed cutting
No. of Flutes
Type
Work Material
P
Dimensions
CARBIDE
BALL
PRFRAD
u e e u u u
1.5
MIRACLE ball nose high power end mill (M), 2 flute 12.5
MS2SB
For Profiling
MS2MB
VC VC2ESB
VC VC2MB
C2MB
SOLID END MILLS
For High For Machining of

Ultra high- For HighFor Copper
For
For Difficult-to-cut For Machining
For Machining Forprecision
Efficiency
Precision
of
Hardened
Steels
of
Hardened
Steels
Aluminium
Alloys
Electrodes
Graphite
Materials
Machining
Machining Machining
VC VC2PSB
VC VC2PSBP
MIRACLE ball nose ultra high-precision end mill(S), 2 flute
VF VF2SSB
VF VF2SB
CRN CRN2MB
DF DF2MB
DLC DLC2MB
VC VC3MB
VF VF4MB
VC VC4MB
VQ
VQ4SVB
VF VF4SVB
J038 * PRFRAD : Ball nose end mill radius
J249 J250
PRFRAD
e e u
0.16
u u
J217 J220
PRFRAD
e e u
0.256
u u
J219 J220
PRFRAD
u e e u u u
0.156
J243 J244
PRFRAD
u e e u u u
0.2
12.5
J248 J250
PRFRAD
e u
0.510
u u u u
J269 J270
PRFRAD
e e e
0.056
u u
J245 J247
PRFRAD
e e e
0.026
u u
J246 J247
PRFRAD
u e e e u u
0.56
J228 J231
PRFRAD
u e e e u u
0.110
J229 J231
PRFRAD
0.26
J254 J255
J260 J260
u e
J265 J266
Graphite : e
GFRP : u
CFRP : u
PRFRAD
3 6
PRFRAD
0.110
e u
GFRP : u
CFRP : u
PRFRAD
u e e u u u
110
J276 J277
PRFRAD
0.56
e e e u u
J281 J282
PRFRAD
u e e e u u
0.510
J285 J286
PRFRAD
u u
1 6
e e u
J283 J284
PRFRAD
u u
110
e e
J279 J280
CARBIDE
Page Number
Cutting
Conditions
Dimensions
Aluminium Alloy
N
Copper Alloy
M S
Shape
Product
Code
Size Range
Coating
Applications,
Features
No. of Flutes
Type
Work Material
P
MP2XLB
MS2XLB
CBN2XLB
VF VF2XLBS
VF VF2XLB
CRN CRN2XLB
DF DF2XLB
PRFRAD
e e u
0.053
u u
J209 J214
PRFRAD
e e u
0.13
u u
J221 J226
PRFRAD
u e e e
0.2 1
J267 J268
PRFRAD
u e e e
0.21
J236 J242
PRFRAD
u e e e
0.13
J237 J242
PRFRAD
0.13
PRFRAD
0.22
Graphite : e
GFRP : u
CFRP : u
e u
J256 J259
J261 J263
For For Deep Slotting of For Deep

Graphite Hardened Steels Slotting
TAPER NECK BALL
VC VCXB
VF VF3XB
DF DF3XB
PRFRAD
u e e u u u
0.56
J251 J253
PRFRAD
u e e e u u
0.42.5
J271 J274
PRFRAD
0.52
Graphite : e
GFRP : u
CFRP : u
SOLID END MILLS
For Copper For Deep Slotting of For Machining For Deep General
For
of Hardened
Slotting Use
Graphite Electrodes Hardened Steels
Steels
LONG NECK BALL
J278 J278
For Profiling
of Special
Geometry
WIDE BALL
VF VF2WB
PRFRAD
u e u
1 3
e e
J227 J227
PRFRAD
e e u
0.21.5
u u
J367 J368
PRFRAD
e e u
0.31
u u
J369 J372
PRFRAD
u e e e u u
0.34
J373 J375
For
For Machining For Rib
Angled Face
of Hardened
Milling Machining
Steels
TAPER BALL
MS2MTB
MS4LTB
VC VC4STB
J039
SOLID END MILLS

Page Number
Cutting
Conditions
Aluminium Alloy
N
Copper Alloy
M S
Shape
Product
Code
Size Range
Coating
Applications,
Features
No. of Flutes
Type
Work Material
P
Dimensions
CARBIDE
SOLID END MILLS
2
4
For Corner Radius
For High- For Machining of For Copper For Corner

For High For High For high feed For
Feed Efficiency
Precision
Machining Machining cutting Graphite Machining Aluminium Alloys Electrodes Radius
RADIUS
MS2MRB
CRN CRN2MRB
C3SARB
VC VCPSRB
Corner radius end mill, Short cut length, 24 flute, High precision
DF DFPSRB
MSMHDRB
VF VFHVRB
VC VCHFRB
MS4MRB
VC VC4SRB
VC VC4JRB
VQ
VQMHVRB
VQ
VQMHVRBF
VF VFMHVRB
VF VFMHVRBCH

VC VCMHDRB
4
6
For Machining
of Hardened
Steels
VF VFFDRB
J040
NEW
DC
112
e e u
J287 J289
u u
DC
612
e u
J298 J299
DC
1225
u e
J304 J305
DC
0.612
J292 J295
e e e e u u
Graphite : e
GFRP : u
CFRP : u
DC
0.512
J345 J347
DC
220
e e u
e e
J311 J313
DC
116
e e e e u u
J315 J317
DC
216
e e e u
J339 J341
DC
320
e e u
u u
J308 J310
DC
412
u e e u u u
J335 J336
DC
320
u e u u u u
J337 J338
DC
220
e u
u e u
J328 J330
DC
616
u u
u e
J333 J334
DC
620
e u u
e e
J325 J326
e e
J327 J327
DC
225
u e e u e e
J342 J344
DC
312
u u e e
J314 J314
DC
1620
CARBIDE
VF VFSDRB
VF VFMDRB
VF VF6MHVRB
VF VF6MHVRBCH
VF VF8MHVRBCH

Page Number
Cutting
Conditions
Dimensions
Aluminium Alloy
N
Copper Alloy
M S
H
Shape
Product
Code
Size Range
Coating
Applications,
Features
For Machining
of Hardened Steels
Materials
No. of Flutes
Type
Work Material
P
DC
312
u e e e
J350 J352
DC
320
u e e e
J351 J352
DC
620
u u u
e e
J348 J349
DC
10,12
16,20
e e
J353 J353
DC
16,20
e e
J354 J354
u u
J290 J291
MS2XLRB
CBN2XLRB
CRN CRN2XLRB
DC
1 6
e e u
DC
0.5 2
u e e e
J302 J303
DC
0.56
e u
J300 J301
DC
1025
J193 J194
DC
325
J195 J196
3
4
For Machining
For
For Difficult-to-cut For Machining
of Hardened Steels Roughing of Aluminium Alloys
Materials
ROUGHING
CSRA
CMRA
VC VCSFPR
VF VFSFPR
VF VFMFPR
VF VFSFPRCH
VF VF6SVRCH
Roughing end mill, Short cut length,

4 flute, with multiple internal through coolant holes
Roughing end mill, Short cut length, 6 flute,
DC
320
e e u
e e
J202 J203
DC
320
e e u
e e
J197 J198
DC
520
e e u
e e
J199 J200
DC
16,20
e e
J201 J201
DC
16,20
e e
J204 J204
SOLID END MILLS
For Copper For Machining For Deep

of Hardened
Electrodes
Slotting
Steels
LONG NECK CORNER RADIUS
J041
SOLID END MILLS
J042
For Machining of
Aluminium Alloys
For
Chamfering
Coating
Applications,
Features
Product
Code
CSRARB
Shape
Corner radius roughing end mill,

Short cut length, 3 flute, For aluminium alloy
VC VC2C
DC
10 25
DC
2 12
Cutting
Conditions
Work Material
Dimensions
Aluminium Alloy
M S
Copper Alloy
H
P
Size Range
CARBIDE
No. of Flutes
Type
SOLID END MILLS

N
Page Number
CORNER RADIUS, ROUGHING
CHAMFER CUTTER
e
J306 J307
e e e u e e u u
J377 J377
HSS (By Series)

Page Number
Cutting
Conditions
Dimensions
Aluminium Alloy
N
Copper Alloy
M S
H
Shape
Product
Code
Size Range
Coating
No. of Flutes
Type
Applications,
Features
Work Material
P
HSS
VA2SS
2
SQUARE
General Use
VA2MS
VA4MC
For Difficultto-cut
Materials
2
3
4
VAMH
VASFPR
Roughing end mill, Short cut length, 46 flute, Fine pitch form
ROUGHING
For Roughing
VAMFPR
Roughing end mill, Medium cut length, 46 flute, Fine pitch form
4
5
6
VAMR
VAJR
Roughing end mill, Semi long cut length, 46 flute
VALR
Roughing end mill, Long cut length, 46 flute
DC
3 20
e u
u u
J380 J382
DC
3 40
e u
u u
J381 J382
DC
3 30
e u
u u
J400 J401
DC
5 30
e u
e u
J397 J398
DC
5 50
e u
e u
J416 J417
DC
5 50
e u
e u
J418 J419
DC
5 50
e u
e u
J420 J421
DC
10 50
e u
e u
J422 J423
DC
10 50
e u
e u
J424 J425
DC
1 40
e u
u u
J387 J388
DC
3 30
e u
u u
J404 J405
DC
3 40
e u
u u
J410 J411
DC
5 50
e u
u u
J414 J415
DC
5 50
e u
u u
J428 J429
DC
e u
0.5 20
u u
J383 J384
DC
e u
0.4 20
u u
J385 J386
TIN COATED END MILLS

G
G2MS
SQUARE
General Use
G4MC
4
G
G4LC
ROUGHING
For Roughing
3
4
6
4
5
6
GSFPR
GMR
SOLID END MILLS
VIOLET END MILLS
SQUARE
General Use
TWO-FLUTE END MILLS
2SS
S2MD
End mill, Short cut length, 2 flute, KHA Super
J043
SOLID END MILLS
END MILLS SELECTION CHART HSS (By Series)

Page Number
Cutting
Conditions
Aluminium Alloy
N
Copper Alloy
M S
H
Shape
Product
Code
Size Range
Coating
No. of Flutes
Type
Applications,
Features
Work Material
P
Dimensions
HSS
2MS
SQUARE
2LS
For Key Way

Slotting
General Use
TWO-FLUTE END MILLS
2MK
End mill, Short cut length, 2 flute, For key ways
DC
1 60
e u
u u
J389 J393
DC
1 40
e u
u u
J391 J393
DC
3 20
e u
J394
DC
e u
2.5 20
u u
J402 J403
DC
e u
2.5 40
u u
J406 J407
DC
3 40
e u
u u
J408 J409
DC
3 40
e u
u u
J412 J413
DC
10 40
e u
u u
J426 J427
DC
5 50
e u
u u
J430 J433
DC
10 50
e u
u u
J431 J433
DC
10 50
e u
u u
J432 J433
PRFRAD
e u
4 25
u u
J434
DC
5 20
u u u u
FOUR-FLUTE END MILLS
S4MD
SQUARE
General Use
4MC
S4JC
4LC
ROUGHING END MILLS
SR
ROUGHING
For Roughing
SOLID END MILLS
4
5
6
MR
JR
LR
ROUGHING
BALL NOSE
MRB
Ball nose roughing end mill, Medium cut length, 4 flute
SQUARE
For Difficultto-cut
Materials
HIGH HELIX END MILLS
2
3
4
KMH
e u
J399 J399
SQUARE
For Machining of For Machining of

Aluminium Alloys Aluminium Sashes
LIGHT ALLOY STEEL END MILLS

1MA
1LA
S2SDA
: Cutting Diameter
* DC
J044 *
DC
3 8
J378
DC
4 12
J379
DC
3 20
u e
J396 J396
HSS (By Shape)

Page Number
Cutting
Conditions
DC
3 8
J378
DC
4 12
J379
Copper Alloy
Dimensions
N
Aluminium Alloy
M S
H
Shape
Product
Code
Size Range
Coating
Applications,
Features
No. of Flutes
Type
Work Material
P
HSS
1MA
1LA
VA2SS
VA2MS
General Use
G2MS
2SS
S2MD
2MS
2LS
2
3
4
For Difficult-to-cut For Machining of For Key Way

Aluminium Alloys Slotting
Materials
2MK
S2SDA
VAMH
KMH
VA4MC
General Use
G4MC
G4LC
S4MD
DC
3 20
e u
u u
J380 J382
DC
3 40
e u
u u
J381 J382
DC
1 40
e u
u u
J387 J388
DC
e u
0.5 20
u u
J383 J384
DC
e u
0.4 20
u u
J385 J386
DC
1 60
e u
u u
J389 J393
DC
1 40
e u
u u
J391 J393
DC
3 20
e u
J394
DC
3 20
u e
SOLID END MILLS
For Machining of
Aluminium Sashes
SQUARE
J396 J396
DC
5 30
e u
e u
J397 J398
DC
5 20
e u
u u u u
J399 J399
DC
3 30
e u
u u
J400 J401
DC
3 30
e u
u u
J404 J405
DC
3 40
e u
u u
J410 J411
DC
e u
2.5 20
u u
J402 J403
J045
SOLID END MILLS
END MILLS SELECTION CHART HSS (By Shape)

Page Number
Cutting
Conditions
Aluminium Alloy
N
Copper Alloy
M S
H
Shape
Product
Code
Size Range
Coating
Applications,
Features
No. of Flutes
Type
Work Material
P
Dimensions
HSS
SQUARE
General Use
4MC
S4JC
4LC
DC
e u
2.5 40
u u
J406 J407
DC
3 40
e u
u u
J408 J409
DC
3 40
e u
u u
J412 J413
DC
5 50
e u
u u
J414 J415
DC
5 50
e u
e u
J416 J417
DC
5 50
e u
e u
J418 J419
DC
5 50
e u
e u
J420 J421
DC
10 50
e u
e u
J422 J423
DC
10 50
e u
e u
J424 J425
DC
5 50
e u
u u
J428 J429
DC
10 40
e u
u u
J426 J427
DC
5 50
e u
u u
J430 J433
DC
10 50
e u
u u
J431 J433
DC
10 50
e u
u u
J432 J433
PRFRAD
e u
4 25
u u
J434
ROUGHING
3
4
6
GSFPR
VASFPR
VAMFPR
SOLID END MILLS
Roughing end mill, Medium cut length, 46 flute, Fine pitch form
VAMR
4
5
6
For Roughing
VAJR
VALR
GMR
SR
MR
JR
LR
For
Roughing
ROUGHING BALL NOSE
MRB
: Cutting Diameter
* DC
*
J046
Ball nose roughing end mill, Medium cut length, 4 flute
Memo
J047
MSTAR END MILLS

CARBIDE
MS2SS
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
UWC
MS
30
DC<3
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DC > 3
Aluminium Alloy
DC
SQUARE
15(10 for 0.1)
DCON(h6)
Type1
APMX
LF
DCON(h6)
DC
Type2
BALL
APMX
h6
DC=0.1
DC>0.1
0
- 0.010
0
- 0.020
LF

0
- 0.008
0
- 0.009
0
- 0.011
J048
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
MS2SSD0010
MS2SSD0020
MS2SSD0030
MS2SSD0040
MS2SSD0050
MS2SSD0060
MS2SSD0070
MS2SSD0080
MS2SSD0090
MS2SSD0100
MS2SSD0120
MS2SSD0150
MS2SSD0180
MS2SSD0200
MS2SSD0250
MS2SSD0300
MS2SSD0400
MS2SSD0500
MS2SSD0600
MS2SSD0700
MS2SSD0800
MS2SSD0900
MS2SSD1000
MS2SSD1100
MS2SSD1200
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.2
1.5
1.8
2
2.5
3
4
5
6
7
8
9
10
11
12
0.15
0.3
0.45
0.6
0.75
0.9
1.1
1.2
1.4
1.5
1.8
2.3
2.7
3
3.8
4.5
6
7.5
9
10.5
12
13.5
15
16.5
18
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
50
50
50
60
60
70
70
75
75
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
8
8
10
10
12
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
2
1
2
DC<3
Titanium Alloy,
Copper Alloy
Aluminium Alloy
15
APMX
h6
DC>12
0
- 0.030
APMX
4<DCON<6 8<DCON<10 12<DCON<16 DCON=20

0
- 0.008
0
- 0.009
0
- 0.011
Type2
Type3
LF
DC
DC < 12
0
- 0.020
Type1
LF
DC
APMX
DC > 3
SQUARE
Austenitic
Stainless Steel
DCON(h6)
Hardened Steel
(>55HRC)
DCON(h6)
CARBIDE
DC
Hardened Steel
( < 55HRC)
30
DCON(h6)
(<30HRC)
( < 45HRC)
MS
UWC
LF
BALL
MS2MS
0
- 0.013
APMX
LF
DCON
Stock
MS2MSD0020
MS2MSD0030
MS2MSD0040
MS2MSD0050
MS2MSD0060
MS2MSD0070
MS2MSD0080
MS2MSD0090
MS2MSD0100
MS2MSD0110
MS2MSD0120
MS2MSD0130
MS2MSD0140
MS2MSD0150
MS2MSD0160
MS2MSD0170
MS2MSD0180
MS2MSD0190
MS2MSD0200
MS2MSD0210
MS2MSD0220
MS2MSD0230
MS2MSD0240
MS2MSD0250
MS2MSD0260
MS2MSD0270
MS2MSD0280
MS2MSD0290
MS2MSD0300
MS2MSD0310
MS2MSD0320
MS2MSD0330
MS2MSD0340
MS2MSD0350
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
3.1
3.2
3.3
3.4
3.5
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
3.8
4
4.2
4.4
4.6
4.8
5
5.2
5.4
5.6
5.8
6
6.2
6.4
6.6
6.8
7
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
45
45
45
45
45
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
J049
MSTAR END MILLS
MS2MS
J050
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
MS2MSD0360
MS2MSD0370
MS2MSD0380
MS2MSD0390
MS2MSD0400
MS2MSD0410
MS2MSD0420
MS2MSD0430
MS2MSD0440
MS2MSD0450
MS2MSD0460
MS2MSD0470
MS2MSD0480
MS2MSD0490
MS2MSD0500
MS2MSD0510
MS2MSD0520
MS2MSD0530
MS2MSD0540
MS2MSD0550
MS2MSD0560
MS2MSD0570
MS2MSD0580
MS2MSD0590
MS2MSD0600
MS2MSD0650
MS2MSD0700
MS2MSD0750
MS2MSD0800
MS2MSD0850
MS2MSD0900
MS2MSD0950
MS2MSD1000
MS2MSD1100
MS2MSD1200
MS2MSD1600
MS2MSD1800
MS2MSD2000
3.6
3.7
3.8
3.9
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
16
18
20
7.2
7.4
7.6
7.8
8
8.2
8.4
8.6
8.8
9
9.2
9.4
9.6
9.8
10
10.2
10.4
10.6
10.8
11
11.2
11.4
11.6
11.8
12
13
14
15
16
17
18
19
20
22
24
32
36
40
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
60
60
60
60
70
70
70
70
75
75
90
90
100
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
16
16
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
2
3
2
MS2SS
MS2MS
CARBIDE
Work
material
Carbon steel, Cast iron, Alloy steel,

Pre-hardened steel
AISI 1050, AISI No 35 B, AISI P20, AISI P21
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.5
2
2.5
3
4
5
6
8
10
12
16
20
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
30000
24000
20000
15000
12000
10000
8000
6400
5400
2400
1900
40
100
200
600
1000
1200
1400
1600
1800
2000
3000
3000
2600
2300
2000
1600
1400
1000
900
820
380
320
0.001
0.002
0.005
0.01
0.015
0.02
0.02
0.03
0.04
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
0.80
1.00
1.00
3.00
4.00
40000
40000
40000
40000
40000
40000
40000
40000
40000
32000
32000
24000
19000
16000
12000
9000
7000
5600
4500
3800
1200
1000
40
100
200
600
960
1200
1400
1600
1600
1600
1900
1900
1600
1400
1200
900
700
550
500
450
100
80
0.001
0.002
0.005
0.01
0.015
0.02
0.02
0.03
0.04
0.06
0.08
0.10
0.13
0.15
0.20
0.25
0.30
0.40
0.50
0.50
0.80
1.00
< Please
refer to the list above

for depth of cut.
Depth of
cut
< 1DC
DC
< Please

for depth of cut.
DC:Dia.
SOLID END MILLS
2) When slotting with end mills with & 3 or larger, reduce the revolution to 50 70% and the feed rate to 40 60%.
J051
MSTAR END MILLS

CARBIDE
MS2MD
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
UWC
MS
30
DC<3
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DC > 3
Aluminium Alloy
Type1
APMX
DCON(h6)
SQUARE
DC
15
LF
DCON(h6)
DC
Type2
APMX
BALL
LF
1 < DC < 12
0
- 0.020
h6

0
- 0.008
0
- 0.009
0
- 0.011
a Strong edge type, 2 flute end mill with high resistance to corner fracturing.
J052
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
MS2MDD0100
MS2MDD0150
MS2MDD0200
MS2MDD0250
MS2MDD0300
MS2MDD0400
MS2MDD0500
MS2MDD0600
MS2MDD0800
MS2MDD1000
MS2MDD1200
1
1.5
2
2.5
3
4
5
6
8
10
12
2.5
3.8
5
6.3
7.5
10
12.5
15
20
25
30
40
40
40
40
50
50
50
50
60
70
90
4
4
4
4
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
2
2
2
CARBIDE

Work
material

Pre-hardened steel
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
1
1.5
2
2.5
3
4
5
6
8
10
12
40000
40000
30000
24000
20000
15000
12000
10000
8000
6400
5400
2000
3000
3000
2600
2300
2000
1600
1400
1000
900
820
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
0.80
1.00
1.00
32000
32000
24000
19000
16000
12000
9000
7000
5600
4500
3800
1600
1900
1900
1600
1400
1200
900
700
550
500
450
0.06
0.08
0.10
0.13
0.15
0.20
0.25
0.30
0.40
0.50
0.50
< Please

for depth of cut.
Depth of
cut
< 1DC
DC
< Please

for depth of cut.
DC:Dia.
SOLID END MILLS
J053
MSTAR END MILLS

CARBIDE
MS2JS
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
MS
UWC
30
DC<3
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
DC<3
DC > 3
Copper Alloy
DC > 3
Aluminium Alloy
15(10 for 0.1)

DCON(h6)
SQUARE
DC
Type1
APMX
LF
DCON(h6)
DC
Type2
APMX
BALL
LF
h6
DC=0.1
DC>0.1
0
- 0.010
0
- 0.020

0
- 0.008
0
- 0.009
0
- 0.011
J054
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
MS2JSD0010
MS2JSD0020
MS2JSD0030
MS2JSD0040
MS2JSD0050
MS2JSD0060
MS2JSD0070
MS2JSD0080
MS2JSD0090
MS2JSD0100
MS2JSD0120
MS2JSD0150
MS2JSD0180
MS2JSD0200
MS2JSD0250
MS2JSD0300
MS2JSD0400
MS2JSD0500
MS2JSD0600
MS2JSD0800
MS2JSD1000
MS2JSD1200
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.2
1.5
1.8
2
2.5
3
4
5
6
8
10
12
0.3
0.6
0.9
1.2
1.5
1.8
2.1
2.4
2.7
3
3.6
4.5
5.4
6
7.5
9
12
15
18
24
30
36
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
50
50
50
70
90
90
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
CARBIDE


Pre-hardened steel

Titanium alloy
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.5
2
2.5
3
4
5
6
8
10
12
40000
40000
40000
32000
25000
21000
18000
16000
14000
13000
8500
6400
5100
4200
3400
2900
2500
1900
1600
1300
Feed rate
(mm/min)
60
60
60
60
65
80
100
120
130
130
120
(40)
(45)
(55)
(60)
(60)
(60)
(60)
(60)
(60)
(60)
(60)
(60)
(60)
(60)
(60)
(60)
(60)
(60)
(60)
(60)
Revolution
(min-1)
Feed rate
(mm/min)
40000
40000
32000
24000
19000
16000
14000
12000
11000
9500
6400
4800
3800
3400
2700
2300
2000
1500
1300
1100
45
45
45
45
55
65
80
100
100
100
100
<0.05DC
(40)
(45)
(45)
(45)
(45)
(45)
(45)
(45)
(45)
(45)
(45)
(45)
(45)
(45)
(45)
(45)
(50)
(50)
(50)
(50)
Revolution
(min-1)
40000
40000
27000
20000
16000
13000
11000
9900
8800
8000
5300
4000
3200
2600
2100
1800
1500
1200
950
800
(1600)
(1350)
(1100)
(900)
(710)
(600)
Feed rate
(mm/min)
35
35
35
40
40
50
60
75
80
75
75
(35)
(35)
(35)
(35)
(35)
(35)
(35)
(35)
(35)
(35)
(35)
(35)
(40)
(40)
(30)
(30)
(30)
(30)
(30)
(30)
Revolution
(min-1)
40000
32000
21000
16000
13000
11000
9100
8000
7100
6400
4200
3200
2500
2100
1700
1500
1300
1000
800
670
(MAX. 0.5mm)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
(25)
<2DC
(DC >&1)
(DC >& 1)
DC
25
25
25
25
25
35
40
50
50
50
50
<0.02DC
<2.5DC
Depth of
cut
Feed rate
(mm/min)
(DC< & 0.5)

(& 0.5 <DC< & 1)
<0.1DC (& 1 <DC< & 2)
<0.2DC (DC >& 2)
<0.02DC
<0.05DC
( ) : Indicates standard revolution and feed rate for slotting.
DC
<0.02DC
<0.05DC
(DC < & 0.5)

(DC <& 0.5)
SOLID END MILLS
Work
material
DC:Dia.
J055
MSTAR END MILLS

CARBIDE
MS2LS
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
MS
UWC
30
DC<3
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
DC<3
DC > 3
Copper Alloy
DC > 3
Aluminium Alloy
Type1
DCON(h6)
SQUARE
DC
15
APMX
LF
DCON(h6)
DC
Type2
APMX
BALL
LF
0.2<DC<12
0
- 0.020
h6

0
- 0.008
0
- 0.009
0
- 0.011
J056
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
MS2LSD0020
MS2LSD0030
MS2LSD0040
MS2LSD0050
MS2LSD0060
MS2LSD0070
MS2LSD0080
MS2LSD0090
MS2LSD0100
MS2LSD0150
MS2LSD0200
MS2LSD0250
MS2LSD0300
MS2LSD0400
MS2LSD0500
MS2LSD0600
MS2LSD0800
MS2LSD1000
MS2LSD1200
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.5
2
2.5
3
4
5
6
8
10
12
0.8
1.2
1.6
2
2.4
2.8
3.2
3.6
4
6
8
10
12
16
20
24
32
40
48
40
40
40
40
40
40
40
40
40
40
40
50
50
50
60
60
70
90
110
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
CARBIDE

y Slotting
Work
material


Pre-hardened steel
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.5
2
2.5
3
4
5
6
8
10
12
40000
40000
40000
40000
33000
28000
25000
22000
20000
13000
10000
9000
8000
6000
4800
4000
3000
2400
2000
400
600
700
800
800
800
800
800
800
800
800
800
800
600
480
400
300
240
200
0.001
0.005
0.007
0.01
0.015
0.015
0.02
0.03
0.04
0.10
0.15
0.20
0.20
0.20
0.30
0.30
0.30
0.30
0.30
30000
35000
30000
24000
21000
18000
16000
15000
13000
9000
6700
6000
5200
4000
3200
2600
2000
1600
1300
250
420
420
380
480
480
480
500
500
500
500
500
460
340
280
210
170
140
110
0.001
0.005
0.007
0.01
0.01
0.015
0.02
0.03
0.04
0.10
0.15
0.20
0.20
0.20
0.20
0.20
0.30
0.30
0.30
DC
Depth of
cut

for depth of cut.
DC:Dia.
y Side milling
Work
material


Pre-hardened steel
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
3
4
5
6
8
10
12
3500
2800
2200
1800
1600
1400
1200
370
370
330
300
270
240
200
0.05
0.06
0.06
0.06
0.08
0.10
0.10
2600
2100
1700
1500
1100
900
750
250
200
160
140
140
140
120
0.03
0.03
0.03
0.03
0.04
0.05
0.06
< Please
Depth of
cut
SOLID END MILLS
< Please
refer to the list above for depth of cut.

<3DC
DC:Dia.
J057
MSTAR END MILLS
MS2XL
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
30
DC<0.4
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DN
Hardened Steel
( < 55HRC)
MS
UWC
DC > 0.4
Aluminium Alloy
12
SQUARE
DC
Type1
DCON(h6)
CARBIDE
APMX
LU
DN
LF
h6
DC<0.5
DC > 0.5
0
- 0.010
0
- 0.020
APMX
LU
DCON(h6)
BALL
DC
Type2
LF
4 < DCON < 6

0
- 0.008
a 2 flute long neck end mill.
J058
Order Number
DC
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
MS2XLD0020N005
MS2XLD0020N010
MS2XLD0020N015
MS2XLD0030N010
MS2XLD0030N020
MS2XLD0030N030
MS2XLD0030N060
MS2XLD0030N090
MS2XLD0040N020
MS2XLD0040N030
MS2XLD0040N040
MS2XLD0040N080
MS2XLD0040N120
MS2XLD0050N020
MS2XLD0050N040
MS2XLD0050N060
MS2XLD0050N080
MS2XLD0050N100
MS2XLD0050N150
MS2XLD0060N020
MS2XLD0060N040
MS2XLD0060N060
MS2XLD0060N080
MS2XLD0060N100
MS2XLD0060N120
MS2XLD0060N180
MS2XLD0070N020
MS2XLD0070N040
MS2XLD0070N060
MS2XLD0070N080
MS2XLD0070N100
MS2XLD0080N040
MS2XLD0080N060
MS2XLD0080N080
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
0.7
0.8
0.8
0.8
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
0.7
0.7
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1
1
1
1
1
1.2
1.2
1.2
0.5
1
1.5
1
2
3
6
9
2
3
4
8
12
2
4
6
8
10
15
2
4
6
8
10
12
18
2
4
6
8
10
4
6
8
0.17
0.17
0.17
0.27
0.27
0.27
0.27
0.27
0.36
0.36
0.36
0.36
0.36
0.46
0.46
0.46
0.46
0.46
0.46
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.66
0.66
0.66
0.66
0.66
0.76
0.76
0.76
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
50
50
50
45
45
45
50
50
50
50
45
45
45
50
50
45
45
50
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CARBIDE
LF
DCON
Stock
MS2XLD0080N100
MS2XLD0080N120
MS2XLD0080N160
MS2XLD0080N240
MS2XLD0090N060
MS2XLD0090N080
MS2XLD0090N100
MS2XLD0090N150
MS2XLD0100N040
MS2XLD0100N060
MS2XLD0100N080
MS2XLD0100N100
MS2XLD0100N120
MS2XLD0100N160
MS2XLD0100N200
MS2XLD0100N250
MS2XLD0100N300
MS2XLD0120N060
MS2XLD0120N080
MS2XLD0120N100
MS2XLD0120N120
MS2XLD0120N160
MS2XLD0120N200
MS2XLD0150N060
MS2XLD0150N080
MS2XLD0150N100
MS2XLD0150N120
MS2XLD0150N140
MS2XLD0150N160
MS2XLD0150N180
MS2XLD0150N200
MS2XLD0150N250
MS2XLD0150N300
MS2XLD0150N380
MS2XLD0150N450
MS2XLD0200N060
MS2XLD0200N080
MS2XLD0200N100
MS2XLD0200N120
MS2XLD0200N140
MS2XLD0200N160
MS2XLD0200N180
MS2XLD0200N200
MS2XLD0200N250
MS2XLD0200N300
MS2XLD0200N350
MS2XLD0200N400
MS2XLD0200N500
MS2XLD0200N600
MS2XLD0250N080
MS2XLD0250N120
MS2XLD0250N160
0.8
0.8
0.8
0.8
0.9
0.9
0.9
0.9
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
1.2
1.2
1.2
1.2
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.8
1.8
1.8
1.8
1.8
1.8
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3.7
3.7
3.7
10
12
16
24
6
8
10
15
4
6
8
10
12
16
20
25
30
6
8
10
12
16
20
6
8
10
12
14
16
18
20
25
30
38
45
6
8
10
12
14
16
18
20
25
30
35
40
50
60
8
12
16
0.76
0.76
0.76
0.76
0.86
0.86
0.86
0.86
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.14
1.14
1.14
1.14
1.14
1.14
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.4
2.4
2.4
50
50
50
60
45
50
50
60
50
50
50
50
50
60
60
70
70
50
50
50
50
60
60
50
50
50
50
60
60
60
60
70
70
80
80
50
50
50
50
60
60
60
60
70
70
80
90
100
110
50
50
60
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SQUARE
DN
BALL
LU
RADIUS
APMX
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J059
MSTAR END MILLS
MS2XL
J060
Order Number
DC
APMX
LU
DN
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
MS2XLD0250N200
MS2XLD0250N250
MS2XLD0250N300
MS2XLD0250N400
MS2XLD0250N500
MS2XLD0300N080
MS2XLD0300N120
MS2XLD0300N160
MS2XLD0300N200
MS2XLD0300N250
MS2XLD0300N300
MS2XLD0300N400
MS2XLD0300N500
MS2XLD0400N120
MS2XLD0400N160
MS2XLD0400N200
MS2XLD0400N250
MS2XLD0400N300
MS2XLD0400N350
MS2XLD0400N400
MS2XLD0400N450
MS2XLD0400N500
MS2XLD0400N600
MS2XLD0500N160
MS2XLD0500N250
MS2XLD0500N350
MS2XLD0500N500
MS2XLD0500N600
MS2XLD0600N200
MS2XLD0600N300
MS2XLD0600N400
MS2XLD0600N500
MS2XLD0600N600
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
6
6
6
6
6
3.7
3.7
3.7
3.7
3.7
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
6
6
6
6
6
6
6
6
6
6
7.5
7.5
7.5
7.5
7.5
9
9
9
9
9
20
25
30
40
50
8
12
16
20
25
30
40
50
12
16
20
25
30
35
40
45
50
60
16
25
35
50
60
20
30
40
50
60
2.4
2.4
2.4
2.4
2.4
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
3.8
3.8
3.8
3.8
3.8
3.8
3.8
3.8
3.8
3.8
4.8
4.8
4.8
4.8
4.8
5.8
5.8
5.8
5.8
5.8
60
70
70
90
100
50
50
60
60
70
70
90
100
50
60
60
70
70
80
90
90
100
110
60
70
80
110
120
80
90
100
110
120
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
CARBIDE

Work material

Dia.
Neck length
DC (mm) LU (mm)
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.2
0.5
1
1
3
9
2
4
12
2
6
10
15
2
6
10
18
2
6
8
10
4
8
12
24
6
10
15
6
8
12
20
30
6
8
12
20

Pre-hardened steel
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
40000
40000
40000
40000
22000
40000
40000
17000
40000
40000
25000
14000
40000
40000
25000
12000
40000
40000
30000
11000
40000
40000
25000
10000
40000
35000
9000
40000
40000
30000
15000
8000
40000
40000
25000
6500
600
400
650
500
150
800
800
150
950
700
400
150
950
800
450
150
1000
900
700
300
1200
1000
400
150
1300
1000
400
1600
1600
1000
400
150
1900
1900
1000
150
0.004
0.001
0.007
0.002
0.001
0.007
0.003
0.001
0.01
0.003
0.002
0.001
0.01
0.005
0.003
0.001
0.02
0.01
0.005
0.005
0.02
0.01
0.003
0.001
0.02
0.01
0.003
0.04
0.03
0.02
0.005
0.001
0.06
0.04
0.03
0.01
Dia.
Neck length
DC (mm) LU (mm)
1.5
1.6
2.5
6
10
20
30
45
6
10
16
6
10
16
30
40
60
8
16
20
40
50
8
16
20
40
50
12
20
30
40
50
60
16
35
60
20
40
60
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
40000
30000
15000
7500
5000
40000
30000
20000
40000
30000
20000
8000
6000
4200
25000
18000
12000
8000
4000
20000
15000
10000
5000
3700
15000
11000
6400
4500
2800
1800
12000
5100
2200
10000
4200
1900
2400
1800
600
300
150
2400
1800
1000
2400
1800
1000
500
250
150
2500
1700
1000
400
150
2000
1400
800
250
150
3000
2200
1200
400
150
60
2500
750
150
2000
800
150
0.10
0.05
0.02
0.005
0.001
0.12
0.07
0.04
0.18
0.10
0.06
0.04
0.01
0.003
0.20
0.10
0.08
0.03
0.015
0.30
0.15
0.10
0.02
0.010
0.30
0.22
0.12
0.05
0.018
0.005
0.35
0.15
0.02
0.40
0.20
0.10
SOLID END MILLS
Work material

Pre-hardened steel
ap:Depth of Cut in the Axial Direction
2) Cutting condition may be considerably different due to the overhang (milling depth), depth of cut, and machine tools. Please see the above
table as a standard.
J061
MSTAR END MILLS

CARBIDE
MS2XL6
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
30
Copper Alloy
DN
Hardened Steel
( < 55HRC)
MS
UWC
Aluminium Alloy
15
DCON(h6)
SQUARE
DC
Type1
APMX
LU
LF
DC
15
0.3<DC<2.5
LF
0
- 0.020
DCON=6
0
- 0.008

a & 6 shank type.
Order Number
DC
APMX
LU
DN
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
DCON(h6)
BALL
APMX
h6
J062
Type2
MS2XL6D0030N008
MS2XL6D0030N015
MS2XL6D0040N010
MS2XL6D0040N020
MS2XL6D0050N013
MS2XL6D0050N025
MS2XL6D0060N015
MS2XL6D0060N030
MS2XL6D0070N018
MS2XL6D0070N035
MS2XL6D0080N020
MS2XL6D0080N040
MS2XL6D0090N023
MS2XL6D0090N045
MS2XL6D0100N025
MS2XL6D0100N050
MS2XL6D0110N028
MS2XL6D0110N055
MS2XL6D0120N030
MS2XL6D0120N060
MS2XL6D0130N033
MS2XL6D0130N065
MS2XL6D0140N035
MS2XL6D0140N070
MS2XL6D0150N038
MS2XL6D0150N075
MS2XL6D0160N040
MS2XL6D0160N080
MS2XL6D0170N043
MS2XL6D0170N085
MS2XL6D0180N045
MS2XL6D0180N090
MS2XL6D0190N048
MS2XL6D0190N095
0.3
0.3
0.4
0.4
0.5
0.5
0.6
0.6
0.7
0.7
0.8
0.8
0.9
0.9
1
1
1.1
1.1
1.2
1.2
1.3
1.3
1.4
1.4
1.5
1.5
1.6
1.6
1.7
1.7
1.8
1.8
1.9
1.9
0.8
0.5
0.6
0.6
0.8
0.8
0.9
0.9
1.1
1.1
1.2
1.2
1.4
1.4
1.5
1.5
1.7
1.7
1.8
1.8
2
2
2.1
2.1
2.3
2.3
2.4
2.4
2.6
2.6
2.7
2.7
2.9
2.9
1.5
1
2
1.3
2.5
1.5
3
1.8
3.5
2
4
2.3
4.5
2.5
5
2.8
5.5
3
6
3.3
6.5
3.5
7
3.8
7.5
4
8
4.3
8.5
4.5
9
4.8
9.5
0.27
0.36
0.36
0.46
0.46
0.56
0.56
0.66
0.66
0.76
0.76
0.86
0.86
0.94
0.94
1.04
1.04
1.14
1.14
1.24
1.24
1.34
1.34
1.44
1.44
1.54
1.54
1.64
1.64
1.74
1.74
1.84
1.84
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CARBIDE
LF
DCON
Stock
MS2XL6D0200N050
MS2XL6D0200N100
MS2XL6D0210N053
MS2XL6D0210N105
MS2XL6D0220N055
MS2XL6D0220N110
MS2XL6D0230N058
MS2XL6D0230N115
MS2XL6D0240N060
MS2XL6D0240N120
MS2XL6D0250N063
MS2XL6D0250N125
2
2
2.1
2.1
2.2
2.2
2.3
2.3
2.4
2.4
2.5
2.5
3
3
3.2
3.2
3.3
3.3
3.5
3.5
3.6
3.6
3.8
3.8
5
10
5.3
10.5
5.5
11
5.8
11.5
6
12
6.3
12.5
1.90
1.90
2.00
2.00
2.10
2.10
2.20
2.20
2.30
2.30
2.40
2.40
50
50
50
60
50
60
50
60
50
60
50
60
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
SQUARE
DN
BALL
LU
RADIUS
APMX
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J063
MSTAR END MILLS

CARBIDE
MS2XL6
Work material
Dia.
Neck length
DC (mm) LU (mm)
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
SOLID END MILLS
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
2.1
2.2
2.3
2.4
2.5
1.5
1
2
1.3
2.5
1.5
3
1.8
3.5
2
4
2.3
4.5
2.5
5
2.8
5.5
3
6
3.3
6.5
3.5
7
3.8
7.5
4
8
4.3
8.5
4.5
9
4.8
9.5
5
10
5.3
10.5
5.5
11
5.8
11.5
6
12
6.3
12.5


Pre-hardened steel
Revolution
(min-1)
Feed rate
(mm/min)
40000
500 1000
40000
500 1000
40000
500 1000
33000
500 1000
29000
500 1000
25000
500 1000
22000
500 1000
20000
500 1000
18000
500 1000
16000
500 1000
15000
500 1000
14000
500 1000
13000
500 1000
12000
500 1000
12000
500 1000
11000
500 1000
10000
500 1000
10000
500 1000
9800
500 1000
9600
500 1000
9400
500 1000
9200
500 1000
9000
500 1000
Depth of cut
ap (mm)
0.01
0.007
0.015
0.01
0.02
0.013
0.03
0.018
0.04
0.025
0.06
0.03
0.08
0.05
0.1
0.07
0.12
0.08
0.12
0.08
0.12
0.08
0.12
0.08
0.15
0.1
0.15
0.1
0.17
0.12
0.17
0.12
0.17
0.12
0.2
0.15
0.2
0.15
0.2
0.15
0.2
0.15
0.25
0.2
0.25
0.2
Revolution
(min-1)
Feed rate
(mm/min)
30000
300 800
30000
300 800
30000
300 800
25000
300 800
22000
300 800
20000
300 800
18000
300 800
16000
300 800
14000
300 800
13000
300 800
12000
300 800
11000
300 800
10000
300 800
10000
300 800
9500
300 800
9000
300 800
9000
300 800
9000
300 800
9000
300 800
9000
300 800
8800
300 800
8700
300 800
8500
300 800
Depth of cut
ap (mm)
0.01
0.007
0.015
0.01
0.02
0.013
0.03
0.018
0.04
0.025
0.06
0.03
0.08
0.05
0.1
0.07
0.12
0.08
0.12
0.08
0.12
0.08
0.12
0.08
0.15
0.1
0.15
0.1
0.17
0.12
0.17
0.12
0.17
0.12
0.2
0.15
0.2
0.15
0.2
0.15
0.2
0.15
0.25
0.2
0.25
0.2
J064
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
APMX
0
- 0.020
h6
APMX
4<DCON<6 7<DCON<10
0
- 0.008
Type2
Type3
LF
DC
3 < DC < 12
Type1
LF
DC
APMX
SQUARE
Austenitic
Stainless Steel
BALL
Hardened Steel
(>55HRC)
CARBIDE
DCON(h6)
Hardened Steel
( < 55HRC)
30
DCON(h6)
(<30HRC)
( < 45HRC)
MS
UWC
DCON(h6)
MS2ES
LF
0
- 0.009
DC
APMX
LF
DCON
Stock
MS2ESD0300L35S04
MS2ESD0350L35S04
MS2ESD0400L35S04
MS2ESD0500L35S05
MS2ESD0500L35S06
MS2ESD0600L35S05
MS2ESD0600L35S06
MS2ESD0700L35S07
MS2ESD0800L35S07
MS2ESD0800L35S08
MS2ESD1000L35S07
MS2ESD1000L35S10
MS2ESD1200L35S10
3
3.5
4
5
5
6
6
7
8
8
10
10
12
3
3.5
4
5
5
6
6
6
6
6
6
6
6
35
35
35
35
35
35
35
35
35
35
35
35
35
4
4
4
5
6
5
6
7
7
8
7
10
10
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
2
2
1
3
2
2
3
2
3
2
3
a
a
a
a
a
a
a
a
a
a
a
a
Overall length 45mm
Type
TAPER
Order Number
No. of
Flutes
Unit : mm
SOLID END MILLS
Overall length 35mm
RADIUS
a 2 flute end mill.
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
MS2ESD0300L45S04
MS2ESD0350L45S04
MS2ESD0400L45S04
MS2ESD0500L45S06
MS2ESD0600L45S06
MS2ESD0700L45S07
MS2ESD0800L45S07
MS2ESD0800L45S08
MS2ESD1000L45S07
MS2ESD1000L45S10
MS2ESD1200L45S10
3
3.5
4
5
6
7
8
8
10
10
12
3
3.5
4
5
6
7
8
8
10
10
12
45
45
45
45
45
45
45
45
45
45
45
4
4
4
6
6
7
7
8
7
10
10
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
2
1
2
2
3
2
3
2
3
J065
MSTAR END MILLS

CARBIDE
MS2ES
Work
material


Pre-hardened steel

Titanium alloy
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
7
8
10
12
10000
7500
6000
5000
4500
4000
3200
2700
600
600
600
600
560
520
450
410
7000
5200
4200
3500
3000
2800
2200
1900
400
400
400
400
360
350
300
270
6000
4500
3600
3000
2700
2400
1900
1600
300
300
300
300
280
260
230
210
5000
4000
3200
2700
2300
2000
1600
1300
120
120
120
120
110
110
100
100
<0.2DC
Depth of
cut
<1DC
DC
<0.05DC
<0.2DC
<1DC
DC
<0.1DC
DC:Dia.
SOLID END MILLS
J066
IMPACT MIRACLE END MILLS
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
UWC
Austenitic
Stainless Steel
VF
35
CARBIDE
DC<3
Titanium Alloy,
Copper Alloy
DC > 3
Aluminium Alloy
15
APMX
DCON(h6)
DC
Type1
LF
LF
0.5 < DC < 6
BALL
DCON(h6)
DC
Type2
APMX
0
- 0.020
h6
SQUARE
VF2MD
4 < DCON < 6

0
- 0.008
APMX
LF
DCON
Stock
VF2MDD0050
VF2MDD0100
VF2MDD0150
VF2MDD0200
VF2MDD0250
VF2MDD0300
VF2MDD0400
VF2MDD0500
VF2MDD0600
0.5
1
1.5
2
2.5
3
4
5
6
1.3
2.5
3.8
5
6.3
7.5
10
12.5
15
40
40
40
40
40
50
50
50
50
4
4
4
4
4
6
6
6
6
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute end mill suitable for high-speed machining of hardened steel.
J067

CARBIDE
VF2MD
Work
material

Pre-hardened steel
AISI H13
AISI D2
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
0.5
1
1.5
2
2.5
3
4
5
6
40000
40000
40000
30000
24000
20000
15000
12000
10000
1000
2000
3000
3000
2600
2300
2000
1600
1400
0.015
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
40000
32000
32000
24000
19000
16000
12000
9000
7000
960
1600
1900
1900
1600
1400
1200
900
700
0.015
0.06
0.08
0.10
0.13
0.15
0.20
0.25
0.30
30000
16000
10600
8100
6400
5400
4000
3200
2700
600
550
500
400
350
300
240
190
160
0.01
0.05
0.08
0.1
0.13
0.15
0.2
0.2
0.2
< Please

for depth of cut.
Depth of
cut
< 1DC
DC
< Please

for depth of cut.
DC:Dia.
SOLID END MILLS
J068
VF2MV
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
UWC
VF
32.5
37.5
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
DC
Type1
DCON(h6)
APMX
DC
LF
LF
0.5 < DC < 6
BALL
DCON(h6)
Type2
APMX
0
- 0.020
h6
SQUARE
15
4 < DCON < 6

0
- 0.008
APMX
LF
DCON
Stock
VF2MVD0050
VF2MVD0100
VF2MVD0150
VF2MVD0200
VF2MVD0250
VF2MVD0300
VF2MVD0400
VF2MVD0500
VF2MVD0600
0.5
1
1.5
2
2.5
3
4
5
6
1.3
2.5
3.8
5
6.3
7.5
10
12.5
15
40
40
40
40
40
50
50
50
50
4
4
4
4
4
6
6
6
6
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a An irregular helix 2 flute square end mill suitable for high-speed machining of hardened steel.
J069

CARBIDE
VF2MV
Work
material

Pre-hardened steel
AISI H13
AISI D2
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
0.5
1
1.5
2
2.5
3
4
5
6
40000
40000
40000
30000
24000
20000
15000
12000
10000
1000
2000
3000
3000
2600
2300
2000
1600
1400
0.015
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
40000
32000
32000
24000
19000
16000
12000
9000
7000
960
1600
1900
1900
1600
1400
1200
900
700
0.015
0.06
0.08
0.10
0.13
0.15
0.20
0.25
0.30
30000
16000
10600
8100
6400
5400
4000
3200
2700
600
550
500
400
350
300
240
190
160
0.01
0.05
0.08
0.1
0.13
0.15
0.2
0.2
0.2
< Please

for depth of cut.
Depth of
cut
< 1DC
DC
< Please

for depth of cut.
DC:Dia.
SOLID END MILLS
1) When slotting, reduce the revolutions by 50 70% and the feed rate by 40 60%.
2) For austenitic stainless steels, titanium and heat-resistant alloys, the VFMHV is recommended.
3) The irregular helix flute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity of
the machine or the workpiece installation is poor, vibration or abonrmal sound can occur. In this case, please reduce the revolution and feed
rate proportionately, or set a lower depth of cut.
J070
(<30HRC)
( < 45HRC)
CARBIDE
DC<3
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
30
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DN
VF
UWC
DC=3
Aluminium Alloy
DC
12
DCON(h6)
Type1
APMX
LU
BALL
LF
0.1 < DC < 3

0
- 0.020
h6
SQUARE
VF2XL
4 < DCON < 6

0
- 0.008
APMX
LU
DN
LF
DCON
Stock
VF2XLD0010N005
VF2XLD0020N006
VF2XLD0020N010
VF2XLD0020N015
VF2XLD0030N010
VF2XLD0030N020
VF2XLD0030N030
VF2XLD0040N010
VF2XLD0040N020
VF2XLD0040N040
VF2XLD0050N020
VF2XLD0050N040
VF2XLD0050N060
VF2XLD0060N020
VF2XLD0060N040
VF2XLD0060N060
VF2XLD0080N040
VF2XLD0080N060
VF2XLD0080N080
VF2XLD0080N100
VF2XLD0100N040
VF2XLD0100N060
VF2XLD0100N080
VF2XLD0100N100
VF2XLD0100N120
VF2XLD0150N060
VF2XLD0150N080
VF2XLD0150N100
VF2XLD0150N120
VF2XLD0150N160
VF2XLD0200N060
VF2XLD0200N080
VF2XLD0200N100
VF2XLD0200N120
0.1
0.2
0.2
0.2
0.3
0.3
0.3
0.4
0.4
0.4
0.5
0.5
0.5
0.6
0.6
0.6
0.8
0.8
0.8
0.8
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
2
2
2
2
0.15
0.3
0.3
0.3
0.5
0.5
0.5
0.6
0.6
0.6
0.8
0.8
0.8
0.9
0.9
0.9
1.2
1.2
1.2
1.2
1.5
1.5
1.5
1.5
1.5
2.3
2.3
2.3
2.3
2.3
3
3
3
3
0.5
0.6
1
1.5
1
2
3
1
2
4
2
4
6
2
4
6
4
6
8
10
4
6
8
10
12
6
8
10
12
16
6
8
10
12
0.085
0.17
0.17
0.17
0.27
0.27
0.27
0.36
0.36
0.36
0.46
0.46
0.46
0.56
0.56
0.56
0.76
0.76
0.76
0.76
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.44
1.9
1.9
1.9
1.9
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
60
50
50
50
50
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute long neck end mill for high-speed machining of hardened steels.
J071
VF2XL
DC
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
VF2XLD0200N160
VF2XLD0200N200
VF2XLD0300N120
VF2XLD0300N160
VF2XLD0300N200
2
2
3
3
3
3
3
4.5
4.5
4.5
16
20
12
16
20
1.9
1.9
2.9
2.9
2.9
60
60
50
60
60
4
4
6
6
6
2
2
2
2
2
RADIUS
TAPER
SOLID END MILLS
J072
Unit : mm
Order Number
BALL
SQUARE
CARBIDE
a
a
a
a
Type
1
1
1
1
1
CARBIDE

AISI H13
AISI D2
Neck length
Dia.
DC (mm) LU (mm)
0.1
0.2
0.3
0.4
0.5
0.6
0.8
1.5
0.5
0.6
1
1.5
1
2
3
1
2
4
2
4
6
2
4
6
4
6
8
10
4
6
8
10
12
6
8
10
12
16
6
8
10
12
16
20
12
16
20
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut per pass

ap (mm)
Revolution
(min-1)
Feed rate
(mm/min)

ap (mm)
40000
40000
40000
40000
40000
40000
38000
40000
40000
36000
40000
36000
30000
40000
36000
30000
36000
30000
24000
20000
32000
32000
28000
28000
24000
22000
22000
22000
20000
18000
16000
16000
16000
16000
15000
14000
11000
11000
11000
100
400
300
200
500
400
250
800
500
300
800
600
400
1000
800
600
1200
900
600
400
1600
1400
1000
800
500
1200
1100
1000
800
500
1000
1000
800
800
600
500
800
600
500
0.002
0.004
0.003
0.002
0.006
0.003
0.002
0.008
0.007
0.004
0.01
0.008
0.005
0.015
0.01
0.006
0.03
0.02
0.01
0.008
0.05
0.04
0.03
0.02
0.02
0.08
0.07
0.06
0.05
0.03
0.15
0.15
0.1
0.08
0.06
0.05
0.2
0.15
0.1
40000
40000
40000
40000
40000
38000
36000
36000
30000
27000
30000
27000
22000
30000
27000
22000
27000
22000
18000
15000
24000
24000
21000
21000
18000
16000
16000
16000
15000
13000
12000
12000
12000
12000
11000
10000
8200
8200
8200
80
360
250
150
450
350
200
500
350
200
600
450
300
700
500
350
900
650
450
300
1100
1000
750
600
370
900
800
750
600
350
750
750
600
600
450
350
600
450
350
0.001
0.004
0.002
0.001
0.004
0.002
0.001
0.006
0.005
0.003
0.009
0.007
0.004
0.012
0.01
0.006
0.02
0.015
0.008
0.005
0.04
0.03
0.02
0.015
0.01
0.06
0.05
0.04
0.03
0.02
0.15
0.1
0.08
0.06
0.05
0.04
0.15
0.15
0.1
SOLID END MILLS
Work material
DC
Depth of cut
< ap
DC:Dia.
J073
MIRACLE END MILLS

CARBIDE
VC2SS
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
UWC
VC
30
DC<3
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DC > 3
Aluminium Alloy
DC
SQUARE
15
DCON(h6)
Type1
APMX
LF
DCON(h6)
DC
Type2
BALL
APMX
DC < 12
0
- 0.020
h6
LF
DC>12
0
- 0.030
DCON=6 8<DCON<10 12<DCON<16

0
- 0.008
0
- 0.009
0
- 0.011
J074
DC
APMX
LF
DCON
VC2SSD0030
VC2SSD0040
VC2SSD0050
VC2SSD0060
VC2SSD0070
VC2SSD0080
VC2SSD0090
VC2SSD0100
VC2SSD0110
VC2SSD0120
VC2SSD0130
VC2SSD0140
VC2SSD0150
VC2SSD0160
VC2SSD0170
VC2SSD0180
VC2SSD0190
VC2SSD0200
VC2SSD0210
VC2SSD0220
VC2SSD0230
VC2SSD0240
VC2SSD0250
VC2SSD0260
VC2SSD0270
VC2SSD0280
VC2SSD0290
VC2SSD0300
VC2SSD0350
VC2SSD0400
VC2SSD0450
VC2SSD0500
VC2SSD0550
VC2SSD0600
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
3.5
4
4.5
5
5.5
6
0.6
0.8
0.8
1
1
1.3
1.3
1.5
1.5
2
2
2
2.5
2.5
2.5
3
3
3
3
3.5
3.5
3.5
4
4
4
4
4.5
4.5
5.5
6
7
7.5
8.5
9
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
Stock
Order Number
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
Unit : mm
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
CARBIDE
DC
APMX
LF
DCON
Stock
VC2SSD0800
VC2SSD1000
VC2SSD1200
VC2SSD1400
VC2SSD1500
VC2SSD1600
8
10
12
14
15
16
12
15
18
21
23
24
60
70
75
75
80
90
8
10
12
16
16
16
2
2
2
2
2
2
a
a
a
a
a
2
2
2
1
1
2
BALL
Type
SQUARE
Order Number
No. of
Flutes
Unit : mm

Pre-hardened steel
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
0.3
0.5
1
1.5
2
3
4
5
6
8
10
12
16
40000
40000
30000
20000
15000
10000
7500
6000
5000
4000
3200
2700
2000
190
380
720
960
1100
1150
900
720
600
520
450
410
340
40000
40000
20000
14000
10000
7000
5200
4200
3500
2800
2200
1900
1400
190
380
480
670
720
800
620
500
420
350
290
260
210
40000
30000
15000
10000
8000
5000
4000
3200
2700
2000
1600
1300
1000
100
140
180
190
200
210
200
160
140
120
110
100
90
DC
Depth of
cut
< 0.1DC
< 0.2DC
TAPER

SOLID END MILLS
Work
material
RADIUS
y Slotting
(DC < &2)

(DC > &2)
DC:Dia.
J075
MIRACLE END MILLS
VC2MS
e
DC<3
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
SQUARE
15
DC < 12
0
- 0.020
h6
DC>12
0
- 0.030
APMX
DCON=3 4<DCON<6 8<DCON<10 12<DCON<16 20<DCON<25

0
- 0.006
0
- 0.008
0
- 0.009
0
- 0.011
Type2
Type3
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DC > 3
DCON(h6)
Hardened Steel
( < 55HRC)
30
DCON(h6)
(<30HRC)
( < 45HRC)
VC
UWC
DCON(h6)
CARBIDE
LF
0
- 0.013
J076
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VC2MSD0030
VC2MSD0040
VC2MSD0050
VC2MSD0060
VC2MSD0070
VC2MSD0080
VC2MSD0090
VC2MSD0100
VC2MSD0110
VC2MSD0120
VC2MSD0130
VC2MSD0140
VC2MSD0150
VC2MSD0160
VC2MSD0170
VC2MSD0180
VC2MSD0190
VC2MSD0200
VC2MSD0210
VC2MSD0220
VC2MSD0230
VC2MSD0240
VC2MSD0250
VC2MSD0260
VC2MSD0270
VC2MSD0280
VC2MSD0290
VC2MSD0300
VC2MSD0350
VC2MSD0400
VC2MSD0450
VC2MSD0500
VC2MSD0550
VC2MSD0600
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
3.5
4
4.5
5
5.5
6
0.6
0.8
1
1.2
1.4
1.6
2
2.5
2.5
3
3
3
4
4
4
5
5
6
6
6
6
8
8
8
8
8
8
8
10
11
11
13
13
13
38
38
38
38
38
38
38
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
45
45
45
50
50
50
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
CARBIDE
Stock
VC2MSD0650
VC2MSD0700
VC2MSD0750
VC2MSD0800
VC2MSD0850
VC2MSD0900
VC2MSD0950
VC2MSD1000
VC2MSD1050
VC2MSD1100
VC2MSD1150
VC2MSD1200
VC2MSD1250
VC2MSD1300
VC2MSD1400
VC2MSD1500
VC2MSD1600
VC2MSD1700
VC2MSD1800
VC2MSD1900
VC2MSD2000
VC2MSD2200
VC2MSD2400
VC2MSD2500
6.5
7
7.5
8
8.5
9
9.5
10
10.5
11
11.5
12
12.5
13
14
15
16
17
18
19
20
22
24
25
16
16
16
19
19
19
19
22
22
22
22
26
26
26
26
30
32
32
32
32
38
38
45
45
60
60
60
60
70
70
70
70
75
75
75
75
75
75
75
80
90
90
90
100
100
100
120
120
8
8
8
8
10
10
10
10
12
12
12
12
12
12
12
16
16
16
16
20
20
20
25
25
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
2
1
1
1
2
1
1
1
2
3
3
3
1
2
3
3
1
2
3
1
2
SQUARE
DCON
BALL
LF
RADIUS
APMX
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J077
MIRACLE END MILLS
VC2MS
CARBIDE

Work
material

Pre-hardened steel
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
0.3
0.5
1
1.5
2
2.5
3
4
5
6
8
10
12
16
20
40000
40000
40000
40000
30000
24000
20000
15000
12000
10000
8000
6400
5400
2400
1900
200
950
2000
3000
3000
2600
2300
2000
1600
1400
1000
900
820
380
320
0.005
0.015
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
0.80
1.00
1.00
3.00
4.00
40000
40000
32000
32000
24000
19000
16000
12000
9000
7000
5600
4500
3800
1200
1000
200
950
1600
1900
1900
1600
1400
1200
900
700
550
500
450
100
80
0.005
0.015
0.06
0.08
0.10
0.13
0.15
0.20
0.25
0.30
0.40
0.50
0.50
0.80
1.00
< Please

for depth of cut.
Depth of
cut
< DC
DC
< Please

for depth of cut.
SOLID END MILLS
DC:Dia.
J078
1)
2)
3)
4)
If the depth of cut is shallow, the revolution and feed rate can be increased.
When slotting with end mills with & 3 or larger, reduce the revolution to 50 70% and the feed rate to 40 60%.
When drilling, please set the feed rate at 1/3 or below the values above.
If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and
Austenitic
Stainless Steel
Titanium Alloy,
DC<3
DC > 3
Copper Alloy
Aluminium Alloy
DC
15
DC < 12
0
- 0.020
h6
DC>12
0
- 0.030
APMX
4<DCON<6 8<DCON<10 12<DCON<16 20<DCON<25

0
- 0.008
0
- 0.009
0
- 0.011
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DC > 3
SQUARE
DC<3
Hardened Steel
(>55HRC)
LF
BALL
CARBIDE
DCON(h6)
Hardened Steel
( < 55HRC)
30
DCON(h6)
(<30HRC)
( < 45HRC)
VC
UWC
DCON(h6)
VC2JS
0
- 0.013
APMX
LF
DCON
Stock
VC2JSD0100
VC2JSD0150
VC2JSD0200
VC2JSD0250
VC2JSD0300
VC2JSD0350
VC2JSD0400
VC2JSD0450
VC2JSD0500
VC2JSD0550
VC2JSD0600
VC2JSD0650
VC2JSD0700
VC2JSD0750
VC2JSD0800
VC2JSD0850
VC2JSD0900
VC2JSD0950
VC2JSD1000
VC2JSD1050
VC2JSD1100
VC2JSD1150
VC2JSD1200
VC2JSD1300
VC2JSD1400
VC2JSD1500
VC2JSD1600
VC2JSD1700
VC2JSD1800
VC2JSD1900
VC2JSD2000
VC2JSD2200
VC2JSD2400
VC2JSD2500
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
10.5
11
11.5
12
13
14
15
16
17
18
19
20
22
24
25
3.5
5
8
10
12
15
15
15
20
20
20
25
25
25
25
25
25
25
30
30
30
30
30
35
40
40
50
50
50
55
55
65
75
75
40
40
40
40
50
50
50
50
60
60
60
70
70
70
70
90
90
90
90
90
90
90
90
90
110
110
110
110
110
110
110
140
140
140
4
4
4
4
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
12
16
16
16
20
20
20
20
25
25
25
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
2
3
1
1
2
1
1
1
2
1
1
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute end mill with longer cut length than standard.
J079
MIRACLE END MILLS
VC2JS
CARBIDE

Work
material


Pre-hardened steel

Titanium alloy
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
1
2
3
4
5
6
8
10
12
16
20
25
13000
6400
4200
3400
2900
2500
1900
1600
1300
1000
800
650
60 (60)
60 (60)
65 (60)
80 (60)
100 (60)
120 (60)
130 (60)
130 (60)
120 (60)
80 (40)
65 (30)
50 (25)
Revolution
(min-1)
9000
4800
3400
2700
2300
2000
1500
1300
1100
820
650
520
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
35 (35)
45 (45)
55 (55)
65 (30)
80 (40)
100 (50)
100 (50)
100 (50)
90 (45)
65 (30)
50 (25)
40 (20)
6500 (6500)
3500 (3500)
2600 (2600)
2100 (1600)
1800 (1350)
1500 (1100)
1200 (900)
950 (710)
800 (600)
600 (450)
480 (360)
380 (280)
20 (20)
30 (30)
40 (40)
50 (20)
60 (25)
75 (30)
85 (35)
75 (30)
60 (25)
45 (20)
40 (15)
30 (12)
< 0.05DC
Revolution
(min-1)
DC
< 0.02DC
(MAX. 0.5mm)
SOLID END MILLS
( ) : Indicates standard revolution and feed rates for slotting.
J080
1)
2)
3)
4)
(DC=&1)
(&1< DC < &2)
< 0.15DC (&2< DC < &3)
< 0.3DC (DC>&3)
(MAX. 3mm)
< 0.05DC
< 0.1DC
20 (15)
25 (15)
30 (20)
35 (20)
40 (20)
50 (25)
50 (25)
50 (25)
40 (20)
30 (15)
25 (13)
20 (10)
5700
3000
2100
1700
1500
1300
1000
800
670
500
400
320
(MAX. 0.3mm)
< 2DC
< 2.5DC
Depth of
cut
Feed rate
(mm/min)
DC
< 0.05DC
(MAX. 0.5mm)
DC:Dia.
When cutting austenitic stainless steels, the use of water-soluble cutting fluid is effective.
MIRACLE END CRN
CRN2MS
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
UWC
Austenitic
Stainless Steel
CRN
30
CARBIDE
DC<3
Titanium Alloy,
DC > 3
Copper Alloy
Aluminium Alloy
DCON(h6)
DC
Type1
APMX
LF
LF
0
- 0.02
h6
BALL
DCON(h6)
DC
Type2
APMX
0.2<DC<12
SQUARE
15

0
- 0.008
0
- 0.009
0
- 0.011
APMX
LF
DCON
Stock
CRN2MSD0020S04
CRN2MSD0020S06
CRN2MSD0030S04
CRN2MSD0030S06
CRN2MSD0040S04
CRN2MSD0040S06
CRN2MSD0050S04
CRN2MSD0050S06
CRN2MSD0060S04
CRN2MSD0070S04
CRN2MSD0080S04
CRN2MSD0080S06
CRN2MSD0090S04
CRN2MSD0100S04
CRN2MSD0100S06
CRN2MSD0110S04
CRN2MSD0120S04
CRN2MSD0120S06
CRN2MSD0130S04
CRN2MSD0140S04
CRN2MSD0150S04
CRN2MSD0150S06
CRN2MSD0160S04
CRN2MSD0170S04
CRN2MSD0180S04
CRN2MSD0190S04
CRN2MSD0200S06
CRN2MSD0250S06
CRN2MSD0300S06
CRN2MSD0400S06
CRN2MSD0500S06
CRN2MSD0600S06
CRN2MSD0800S08
CRN2MSD1000S10
CRN2MSD1200S12
0.2
0.2
0.3
0.3
0.4
0.4
0.5
0.5
0.6
0.7
0.8
0.8
0.9
1
1
1.1
1.2
1.2
1.3
1.4
1.5
1.5
1.6
1.7
1.8
1.9
2
2.5
3
4
5
6
8
10
12
0.4
0.4
0.6
0.6
0.8
0.8
1
1
1.2
1.4
1.6
1.6
2
2.5
2.5
2.5
3
3
3
3
4
4
4
4
5
5
6
8
8
11
13
13
19
22
26
40
45
40
45
40
45
40
45
40
40
40
45
40
40
45
40
40
45
40
40
40
45
40
40
40
40
45
45
45
45
50
50
60
70
75
4
6
4
6
4
6
4
6
4
4
4
6
4
4
6
4
4
6
4
4
4
6
4
4
4
4
6
6
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute end mill with CRN coating for copper electrode machining.
J081
MIRACLE END CRN

CARBIDE
CRN2MS
Work
material
Copper, Copper alloys
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.5
2
2.5
3
4
5
6
8
10
12
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
30000
24000
20000
15000
12000
10000
8000
6400
5400
600
600
800
960
1200
1400
1600
1800
2000
3000
3000
2600
2300
2000
1600
1400
1000
900
820
0.01
0.01
0.01
0.015
0.02
0.02
0.03
0.04
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
0.80
1.00
1.00

for depth of cut.
DC
SOLID END MILLS
< Please
J082
Depth of
cut
< DC
< Please
refer to
the list above
for depth of cut.
DC:Dia.
1) If the depth of cut is shallow, the revolution and feed rate can be
increased.
2) Water-soluble cutting fluid is recommended.
3) When drilling, please set the feed rate at 1/3 or below of the table
value.
4) If the rigidity of the machine or the work materials installation is
very low, or chattering and noise are generated, reduce the
revolution and feed rate proportionately.
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
30
CARBIDE
DC<3
Austenitic
Stainless Steel
Titanium Alloy,
DC > 3
Copper Alloy
Aluminium Alloy
DN
(<30HRC)
( < 45HRC)
CRN
UWC
DC
15
APMX
LU
DCON(h6)
Type1
DC
DN
LF
SQUARE
CRN2XL
LU
0
- 0.02
LF
BALL
0.2 < DC < 6
h6
DCON(h6)
Type2
APMX
4 < DCON < 6

0
- 0.008
APMX
LU
DN
LF
DCON
Stock
CRN2XLD0020N005S04
CRN2XLD0020N005S06
CRN2XLD0020N010S04
CRN2XLD0020N010S06
CRN2XLD0020N015S04
CRN2XLD0020N015S06
CRN2XLD0030N010S04
CRN2XLD0030N010S06
CRN2XLD0030N030S04
CRN2XLD0030N030S06
CRN2XLD0040N020S04
CRN2XLD0040N020S06
CRN2XLD0040N040S04
CRN2XLD0040N040S06
CRN2XLD0040N060S04
CRN2XLD0040N060S06
CRN2XLD0050N020S04
CRN2XLD0050N020S06
CRN2XLD0050N040S04
CRN2XLD0050N040S06
CRN2XLD0050N060S04
CRN2XLD0050N060S06
CRN2XLD0050N080S04
CRN2XLD0050N080S06
CRN2XLD0080N040S04
CRN2XLD0080N040S06
CRN2XLD0080N060S04
CRN2XLD0080N060S06
CRN2XLD0080N080S04
CRN2XLD0080N080S06
CRN2XLD0080N100S04
CRN2XLD0080N100S06
CRN2XLD0100N060S04
CRN2XLD0100N060S06
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
0.3
0.3
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.5
1.5
0.5
0.5
1
1
1.5
1.5
1
1
3
3
2
2
4
4
6
6
2
2
4
4
6
6
8
8
4
4
6
6
8
8
10
10
6
6
0.17
0.17
0.17
0.17
0.17
0.17
0.27
0.27
0.27
0.27
0.36
0.36
0.36
0.36
0.36
0.36
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.94
0.94
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute long neck end mill with CRN coating for copper electrode machining.
J083
MIRACLE END CRN
CRN2XL
Order Number
DC
APMX
LU
DN
LF
DCON
Stock
CRN2XLD0100N080S04
CRN2XLD0100N080S06
CRN2XLD0100N100S04
CRN2XLD0100N100S06
CRN2XLD0100N120S04
CRN2XLD0100N120S06
CRN2XLD0100N160S04
CRN2XLD0100N160S06
CRN2XLD0150N060S04
CRN2XLD0150N060S06
CRN2XLD0150N080S04
CRN2XLD0150N080S06
CRN2XLD0150N100S04
CRN2XLD0150N100S06
CRN2XLD0150N120S04
CRN2XLD0150N120S06
CRN2XLD0150N160S04
CRN2XLD0150N160S06
CRN2XLD0150N200S04
CRN2XLD0150N200S06
CRN2XLD0200N060S06
CRN2XLD0200N080S06
CRN2XLD0200N100S06
CRN2XLD0200N120S06
CRN2XLD0200N160S06
CRN2XLD0200N200S06
CRN2XLD0250N080S06
CRN2XLD0250N120S06
CRN2XLD0250N160S06
CRN2XLD0250N200S06
CRN2XLD0300N200S06
CRN2XLD0400N200S06
CRN2XLD0500N250S06
CRN2XLD0600N300S06
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2.5
2.5
2.5
2.5
3
4
5
6
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
3.0
3.0
3.0
3.0
3.0
3.0
3.8
3.8
3.8
3.8
4.5
6.0
7.5
9.0
8
8
10
10
12
12
16
16
6
6
8
8
10
10
12
12
16
16
20
20
6
8
10
12
16
20
8
12
16
20
20
20
25
30
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.90
1.90
1.90
1.90
1.90
1.90
2.40
2.40
2.40
2.40
2.90
3.90
4.90
5.85
50
50
50
50
50
50
55
55
50
50
50
50
50
50
50
50
55
55
60
60
50
50
50
50
55
60
50
55
60
65
65
65
70
70
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
J084
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
CARBIDE
Dia.
DC (mm)
0.2
0.3
0.4
0.5
0.8
1.5
2.5
3
4
5
6
Neck length
LU (mm)
Revolution
(min-1)
Feed rate
(mm/min)

(mm)
0.5
1.0
1.5
1
3
2
4
6
2
4
6
4
6
8
6
8
10
12
6
8
10
12
16
20
6
8
10
12
16
20
8
12
16
20
20
20
25
30
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
30000
30000
40000
40000
40000
30000
20000
15000
40000
40000
40000
30000
30000
15000
40000
40000
30000
20000
20000
15000
12000
10000
800
700
600
800
600
950
800
600
950
800
700
1200
1200
1000
2000
2000
1200
1000
2400
2200
2000
1800
1200
800
2400
2200
2000
1500
1000
600
3000
2800
2100
1000
2000
2000
1500
1200
0.004
0.003
0.002
0.007
0.002
0.007
0.003
0.001
0.01
0.005
0.002
0.02
0.015
0.01
0.04
0.03
0.02
0.015
0.10
0.09
0.08
0.05
0.03
0.02
0.18
0.15
0.12
0.10
0.06
0.03
0.20
0.15
0.10
0.08
0.12
0.30
0.35
0.40
SOLID END MILLS
Work material
J085
MIRACLE END DLC

UWC
DLC
30
DC<3
Aluminium Alloy
Graphite
DC<3
DC > 3
DC
SQUARE
15
LF
DC
APMX
0
- 0.020
h6
DC>12
0
- 0.030
APMX

0
- 0.008
0
- 0.009
0
- 0.011
Type1
Type2
Type3
LF
DC
BALL
APMX
DC < 12
DC > 3
Machineable
Ceramics
DCON(h6)
Copper Alloy
GFRP
CFRP
37.5
DCON(h6)
DLC2MA
DCON(h6)
CARBIDE
LF
0
- 0.013
ideal for machining non-ferrous materials.
J086
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
a 2 flute end mill with new high welding resistance DLC coating,
DLC2MAD0100
DLC2MAD0150
DLC2MAD0200
DLC2MAD0250
DLC2MAD0300
DLC2MAD0350
DLC2MAD0400
DLC2MAD0450
DLC2MAD0500
DLC2MAD0600
DLC2MAD0800
DLC2MAD1000
DLC2MAD1200
DLC2MAD1400
DLC2MAD1500
DLC2MAD1600
DLC2MAD1800
DLC2MAD2000
1
1.5
2
2.5
3
3.5
4
4.5
5
6
8
10
12
14
15
16
18
20
2.5
4
6
8
8
10
11
11
13
13
19
22
26
26
30
32
32
38
40
40
40
40
45
45
45
45
50
50
60
70
75
75
80
90
90
100
4
4
4
4
6
6
6
6
6
6
8
10
12
12
16
16
16
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
2
2
2
2
3
1
2
3
2
CARBIDE

y Side milling
y Slotting
Aluminium alloy
Aluminium cast,
Work
material
Aluminium alloy
Aluminium cast,
Work
material
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
1
2
3
4
5
6
8
10
12
16
20
40000
40000
32000
24000
19000
16000
12000
9500
8000
6000
4800
600
1100
1400
1500
1600
1900
1900
1900
1900
1900
1500
40000
38000
25000
19000
15000
13000
9500
7600
6400
4800
3800
460
850
950
1000
1000
1100
1200
1200
1200
1200
1000
1
2
3
4
5
6
8
10
12
16
20
40000
38000
25000
19000
15000
13000
9500
7600
6400
4800
3800
460
850
950
1000
1000
1100
1200
1200
1200
1000
970
40000
32000
21000
16000
13000
11000
8000
6400
5300
4000
3200
350
550
600
650
700
750
800
800
800
720
660
< 0.2DC
Depth of
cut
< 0.5DC
DC
(DC < & 3)

(DC > & 3)
Depth of
cut
< 1DC
DC:Dia.
< 1DC
(MAX. 12mm)
DC:Dia.
SOLID END MILLS
1) When cutting a very hard workpiece, reduce the feed rate.

J087
END MILL FOR SLOTTING

CARBIDE
SED2KPG
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
MS
UWC
30
DC < 10
Hardened Steel
(>55HRC)
DC>10
Austenitic
Stainless Steel
Titanium Alloy,
DC<3
Copper Alloy
3 < DC < 10
DC > 11
Aluminium Alloy
DC
SQUARE
15
DCON(h6)
Type1
APMX
LF
DCON(h6)
DC
Type2
BALL
APMX
0
+ 0.02
4<DCON<6 8<DCON<10 12<DCON<16

0
- 0.008
0
- 0.009
0
- 0.011
a 2 flute end mill for key way slotting with plus tolerance
a cutting diameter.
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
h6
J088
LF
2 < DC < 16
SED2020KPG
SED2030KPG
SED2040KPG
SED2050KPG
SED2060KPG
SED2070KPG
SED2080KPG
SED2100KPG
SED2120KPG
SED2140KPG
SED2150KPG
SED2160KPG
2
3
4
5
6
7
8
10
12
14
15
16
3
5
6
8
9
10
12
15
15
15
15
15
45
45
45
50
50
60
60
65
65
70
70
70
4
6
6
6
6
8
8
10
12
16
16
16
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
2
1
2
2
2
1
1
2
SED2KMG
End mill, Medium cut length, 2 flute, - Tolerance
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
MS
UWC
30
CARBIDE
DC < 10
Hardened Steel
(>55HRC)
DC>10
Austenitic
Stainless Steel
Titanium Alloy,
DC<3
Copper Alloy
3 < DC < 10
DC > 11
Aluminium Alloy
DCON(h6)
Type1
APMX
LF
LF
0
- 0.02
4<DCON<6 8<DCON<10 12<DCON<16

0
- 0.011
a 2 flute end mill for key way slotting with minus tolerance
a cutting diameter.
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
SED2020KMG
SED2030KMG
SED2040KMG
SED2050KMG
SED2060KMG
SED2070KMG
SED2080KMG
SED2100KMG
SED2120KMG
SED2140KMG
SED2150KMG
SED2160KMG
2
3
4
5
6
7
8
10
12
14
15
16
3
5
6
8
9
10
12
15
15
15
15
15
45
45
45
50
50
60
60
65
65
70
70
70
4
6
6
6
6
8
8
10
12
16
16
16
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
2
1
2
2
2
1
1
2
RADIUS
0
- 0.009
TAPER
0
- 0.008
SOLID END MILLS
h6
BALL
DCON(h6)
DC
Type2
APMX
2 < DC < 16
SQUARE
DC
15
J089
END MILL FOR SLOTTING
SED2KPG
SED2KMG
End mill, Short cut length, 2 flute, For key ways End mill, Short cut length, 2 flute, For key ways
CARBIDE

Work
material
Carbon steel, Alloy steel

(180 280HB)

(280 380HB)
AISI 1045, AISI P20
AISI 1045, AISI P20
Pre-hardened steel
(35 45HRC)
Stainless steel (270HB > )
Cast iron
(Tensile Strength 350MPa> )
AISI 420
AISI No 35 B
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
8
10
12
14
16
13000
8500
6500
5100
4300
3200
2600
2200
1900
1600
260 (260)
340 (340)
380 (380)
400 (400)
410 (410)
410 (410)
400 (400)
360 (360)
340 (340)
320 (320)
10300
6900
5200
4100
3400
2600
2070
1700
1500
1300
200 (200)
200 (200)
250 (200)
290 (230)
290 (230)
250 (200)
240 (190)
210 (170)
200 (160)
200 (160)
8800
6400
4400
3500
2900
2200
1800
1500
1250
1100
110 (110)
110 (110)
140 (110)
140 (110)
150 (120)
140 (110)
140 (110)
130 (100)
130 (100)
130 (100)
9800
6400
4800
3800
3200
2400
1900
1600
1400
1200
170 (170)
170 (170)
200 (160)
190 (150)
180 (140)
150 (120)
140 (110)
130 (105)
130 (100)
120 (95)
21500
14300
10700
8600
7200
5400
4300
3600
3100
2700
830 (830)
850 (850)
860 (860)
850 (850)
870 (870)
880 (880)
860 (860)
860 (860)
860 (860)
870 (870)
< 0.1DC
Depth of
cut
< 1DC
DC
< 0.25DC
< 0.5DC
(DC < & 3)

(DC > & 3)
DC:Dia.
( ) : Indicates standard feed rate for slotting.
SOLID END MILLS
1)
2)
3)
4)
J090
The cutting conditions above are a guide only to milling within the standard depth of cut.
Ductile cast iron milling has the same cutting conditions as carbon steel and alloy steel. (180 280HB)
When drilling, please set the feed rate at 1/3 or below of the values above.
CARBIDE END MILLS
C2SS
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
30
UWC
CARBIDE
DC<3
Hardened Steel
(>55HRC)
DC > 3
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DCON(h6)
Type1
APMX
DC
LF
LF
0
- 0.020
h6
BALL
DCON(h6)
Type2
APMX
0.4 < DC < 6
SQUARE
DC
15
4 < DCON < 6

0
- 0.008
APMX
LF
DCON
Stock
C2SSD0040
C2SSD0050
C2SSD0060
C2SSD0070
C2SSD0080
C2SSD0090
C2SSD0100
C2SSD0110
C2SSD0120
C2SSD0130
C2SSD0140
C2SSD0150
C2SSD0160
C2SSD0170
C2SSD0180
C2SSD0190
C2SSD0200
C2SSD0210
C2SSD0220
C2SSD0230
C2SSD0240
C2SSD0250
C2SSD0260
C2SSD0270
C2SSD0280
C2SSD0290
C2SSD0300
C2SSD0350
C2SSD0400
C2SSD0450
C2SSD0500
C2SSD0550
C2SSD0600
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
3.5
4
4.5
5
5.5
6
0.8
0.8
1
1
1.3
1.3
1.5
1.5
2
2
2
2.5
2.5
2.5
3
3
3
3
3.5
3.5
3.5
4
4
4
4
4.5
4.5
5.5
6
7
7.5
8.5
9
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
45
45
45
50
50
50
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute end mill with short rigid geometry.
J091
CARBIDE END MILLS
C2MS
DC<3
Hardened Steel
(>55HRC)
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
SQUARE
15
LF
DC
APMX
0
- 0.020
h6
DC>12
0
- 0.030
APMX

0
- 0.008
0
- 0.009
0
- 0.011
Type1
Type2
Type3
LF
DC
BALL
APMX
DC < 12
DC > 3
Austenitic
Stainless Steel
DCON(h6)
Hardened Steel
( < 55HRC)
DCON(h6)
(<30HRC)
( < 45HRC)
30
UWC
DCON(h6)
CARBIDE
LF
0
- 0.013
J092
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
C2MSD0100
C2MSD0110
C2MSD0120
C2MSD0130
C2MSD0140
C2MSD0150
C2MSD0160
C2MSD0170
C2MSD0180
C2MSD0190
C2MSD0200
C2MSD0210
C2MSD0220
C2MSD0230
C2MSD0240
C2MSD0250
C2MSD0260
C2MSD0270
C2MSD0280
C2MSD0290
C2MSD0300
C2MSD0310
C2MSD0320
C2MSD0330
C2MSD0340
C2MSD0350
C2MSD0360
C2MSD0370
C2MSD0380
C2MSD0390
C2MSD0400
C2MSD0410
C2MSD0420
C2MSD0430
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4
4.1
4.2
4.3
2.5
2.5
3
3
3
4
4
4
5
5
6
6
6
6
8
8
8
8
8
8
8
8
8
8
10
10
10
10
11
11
11
11
11
11
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
45
45
45
45
45
45
45
45
45
45
45
45
45
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CARBIDE
Stock
C2MSD0440
C2MSD0450
C2MSD0460
C2MSD0470
C2MSD0480
C2MSD0490
C2MSD0500
C2MSD0510
C2MSD0520
C2MSD0530
C2MSD0540
C2MSD0550
C2MSD0560
C2MSD0570
C2MSD0580
C2MSD0590
C2MSD0600
C2MSD0610
C2MSD0620
C2MSD0630
C2MSD0640
C2MSD0650
C2MSD0660
C2MSD0670
C2MSD0680
C2MSD0690
C2MSD0700
C2MSD0710
C2MSD0720
C2MSD0730
C2MSD0740
C2MSD0750
C2MSD0760
C2MSD0770
C2MSD0780
C2MSD0790
C2MSD0800
C2MSD0810
C2MSD0820
C2MSD0830
C2MSD0840
C2MSD0850
C2MSD0860
C2MSD0870
C2MSD0880
C2MSD0890
C2MSD0900
C2MSD0910
C2MSD0920
C2MSD0930
C2MSD0940
C2MSD0950
4.4
4.5
4.6
4.7
4.8
4.9
5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
7
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
8
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
9
9.1
9.2
9.3
9.4
9.5
11
11
11
11
13
13
13
13
13
13
13
13
13
13
13
13
13
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
50
50
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SQUARE
DCON
BALL
LF
RADIUS
APMX
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J093
CARBIDE END MILLS
C2MS

DC
APMX
LF
DCON
No. of
Flutes
Stock
C2MSD0960
C2MSD0970
C2MSD0980
C2MSD0990
C2MSD1000
C2MSD1100
C2MSD1200
C2MSD1300
C2MSD1400
C2MSD1500
C2MSD1600
C2MSD1700
C2MSD1800
C2MSD1900
C2MSD2000
9.6
9.7
9.8
9.9
10
11
12
13
14
15
16
17
18
19
20
22
22
22
22
22
22
26
26
26
30
32
32
32
32
38
70
70
70
70
70
75
75
75
75
80
90
90
90
100
100
10
10
10
10
10
12
12
12
12
16
16
16
16
20
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
SOLID END MILLS
J094
Unit : mm
Order Number
TAPER
RADIUS
BALL
SQUARE
CARBIDE
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
2
1
2
3
3
1
2
3
3
1
2
DC > 3
DC<3
Copper Alloy
Aluminium Alloy
DC
15
APMX
0
- 0.020
h6
0
- 0.030
APMX

0
- 0.008
0
- 0.009
0
- 0.011
Type2
Type3
LF
DC
DC>12
Type1
LF
DC
APMX
DCON(h6)
Titanium Alloy,
DC < 12
DC > 3
Austenitic
Stainless Steel
SQUARE
DC<3
Hardened Steel
(>55HRC)
DCON(h6)
Hardened Steel
( < 55HRC)
CARBIDE
DCON(h6)
(<30HRC)
( < 45HRC)
30
UWC
BALL
C2JS
LF
0
- 0.013
APMX
LF
DCON
Stock
C2JSD0100
C2JSD0150
C2JSD0200
C2JSD0250
C2JSD0300
C2JSD0350
C2JSD0400
C2JSD0450
C2JSD0500
C2JSD0550
C2JSD0600
C2JSD0650
C2JSD0700
C2JSD0750
C2JSD0800
C2JSD0850
C2JSD0900
C2JSD0950
C2JSD1000
C2JSD1050
C2JSD1100
C2JSD1150
C2JSD1200
C2JSD1300
C2JSD1400
C2JSD1500
C2JSD1600
C2JSD1700
C2JSD1800
C2JSD1900
C2JSD2000
C2JSD2200
C2JSD2400
C2JSD2500
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
10.5
11
11.5
12
13
14
15
16
17
18
19
20
22
24
25
3.5
5
8
10
12
15
15
15
20
20
20
25
25
25
25
25
25
25
30
30
30
30
30
35
40
40
50
50
50
55
55
65
75
75
40
40
40
40
50
50
50
50
60
60
60
70
70
70
70
90
90
90
90
90
90
90
90
90
110
110
110
110
110
110
110
140
140
140
4
4
4
4
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
12
16
16
16
20
20
20
20
25
25
25
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
2
3
1
1
2
1
1
1
2
1
1
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute uncoated end mill for general use.
J095
CARBIDE END MILLS
C2LS
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
SQUARE
DC
15
LF
DC
APMX
APMX
DCON(h6)
Hardened Steel
( < 55HRC)
Type1
DCON(h6)
(<30HRC)
( < 45HRC)
30
UWC
Type2
DCON(h6)
CARBIDE
Type3
DC < 12
0
- 0.020
h6
DC
BALL
LF
DC>12
0
- 0.030
APMX
LF

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
J096
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
C2LSD0100
C2LSD0150
C2LSD0200
C2LSD0250
C2LSD0300
C2LSD0350
C2LSD0400
C2LSD0450
C2LSD0500
C2LSD0550
C2LSD0600
C2LSD0650
C2LSD0700
C2LSD0750
C2LSD0800
C2LSD0850
C2LSD0900
C2LSD0950
C2LSD1000
C2LSD1050
C2LSD1100
C2LSD1150
C2LSD1200
C2LSD1250
C2LSD1300
C2LSD1400
C2LSD1500
C2LSD1600
C2LSD1700
C2LSD1800
C2LSD1900
C2LSD2000
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
10.5
11
11.5
12
12.5
13
14
15
16
17
18
19
20
4
6
9
12
20
22
25
25
30
30
30
30
40
40
40
40
40
40
50
50
50
50
50
50
50
70
70
70
70
70
70
70
40
40
40
40
60
60
60
60
70
70
70
90
90
90
90
100
100
100
100
110
110
110
110
120
120
130
130
130
140
140
140
140
4
4
4
4
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
12
12
16
16
16
20
20
20
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
2
3
3
1
1
2
1
1
1
2
C2SS
End mill, Semi long cut length, 2 flute C2JS
C2MS
C2LS

1)
CARBIDE
2)

Work
material
Structural steel, Cast iron,

Carbon steel

(20 30HRC)

Pre-hardened steel (30 45HRC)

Titanium alloy
AISI 1045, AISI No 35 B, AISI 1050
AISI 1050, AISI P20
AISI H13, AISI P21
AISI 304
Dia.
DC (mm)
Revolution
(min-1)
0.5
1
2
3
4
5
6
8
10
12
16
20
17000
10000
5500
4100
3400
2900
2500
1900
1500
1250
940
750
Feed rate
(mm/min)
50
65
90
100
170
190
200
200
180
150
110
90
(50)
(65)
(90)
(100)
(135)
(150)
(160)
(160)
(145)
(120)
(90)
(70)
(C2SS, C2MS)
Depth of
cut
Revolution
(min-1)
14000
8500
4800
3500
2900
2400
2100
1600
1250
1050
800
640
Feed rate
(mm/min)
45
55
80
85
140
150
170
170
150
130
95
80
< 0.2DC
Revolution
(min-1)
(45)
(55)
(80)
(85)
(110)
(120)
(135)
(135)
(120)
(100)
(75)
(65)
11000
6400
3800
2800
2200
1800
1600
1200
950
800
600
480
Feed rate
(mm/min)
30
40
55
65
90
100
110
105
95
80
60
50
(30)
(40)
(55)
(65)
(70)
(80)
(90)
(85)
(75)
(65)
(50)
(40)
Revolution
(min-1)
9000
5200
3100
2300
1900
1500
1300
1000
800
660
500
400
Feed rate
(mm/min)
30
35
50
60
80
90
95
100
90
75
55
45
(30)
(35)
(50)
(60)
(60)
(60)
(65)
(70)
(65)
(50)
(40)
(30)
DC
(DC < & 2)
(& 2 < DC < & 3)
< 0.5DC (DC < & 3)
< 0.1DC
< 1.5DC
< 0.3DC
DC:Dia.
1) Decrease the feed rate by 20 30% for C2JS.

2) Decrease the revolution by 20 30% and the feed rate by 40 50% for C2LS.
SOLID END MILLS
J097
MIRACLE END ALIMASTER

CARBIDE
C2MA
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
30
UWC
DC<3
Austenitic
Stainless Steel
37.5
DC<3
DC > 3
Titanium Alloy,
Copper Alloy
DC > 3
Aluminium Alloy
h6
DC>12
0
- 0.030
APMX

0
- 0.008
0
- 0.009
0
- 0.011
DCON(h6)
DC < 12
0
- 0.020
Type3
LF
DC
BALL
APMX
Type2
LF
DC
APMX
Type1
DCON(h6)
DC
SQUARE
15
DCON(h6)
LF
0
- 0.013
a 2 flute uncoated end mill designed especially for aluminium alloys.
J098
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
C2MAD0100
C2MAD0150
C2MAD0200
C2MAD0250
C2MAD0300
C2MAD0400
C2MAD0500
C2MAD0600
C2MAD0800
C2MAD1000
C2MAD1200
C2MAD1400
C2MAD1500
C2MAD1600
C2MAD1800
C2MAD2000
1
1.5
2
2.5
3
4
5
6
8
10
12
14
15
16
18
20
2.5
4
6
8
8
11
13
13
19
22
26
26
30
32
32
38
40
40
40
40
45
45
50
50
60
70
75
75
80
90
90
100
4
4
4
4
6
6
6
6
8
10
12
12
16
16
16
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
2
2
2
3
1
2
3
2
CARBIDE

y Side milling
Work
material
y Slotting
Aluminium alloy
Aluminium cast
Work
material
Aluminium alloy
Aluminium cast
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
1
2
3
4
5
6
8
10
12
16
20
40000
40000
32000
24000
19000
16000
12000
9500
8000
6000
4800
600
1100
1400
1500
1600
1900
1900
1900
1900
1900
1500
40000
38000
25000
19000
15000
13000
9500
7600
6400
4800
3800
460
850
950
1000
1000
1100
1200
1200
1200
1200
1000
1
2
3
4
5
6
8
10
12
16
20
40000
38000
25000
19000
15000
13000
9500
7600
6400
4800
3800
460
850
950
1000
1000
1100
1200
1200
1200
1000
970
40000
32000
21000
16000
13000
11000
8000
6400
5300
4000
3200
350
550
600
650
700
750
800
800
800
720
660
< 0.2DC
Depth of
cut
< 0.5DC
(DC < & 3)

(DC > & 3)
DC
Depth of
cut
< 1DC
DC:Dia.
(MAX. 12mm)
DC:Dia.
Water-soluble cutting fluid is recommended.
Climb cutting is recommended for side milling.
SOLID END MILLS
1)
2)
3)
4)
< 1DC
J099

CARBIDE
C2LA
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
UWC
Austenitic
Stainless Steel
30
DC<3
37.5
DC<3
DC > 3
Titanium Alloy,
Copper Alloy
DC > 3
Aluminium Alloy
e
Type1
DCON(h6)
SQUARE
DC
15
APMX
DC
LF
DCON(h6)
Type2
APMX
BALL
LF
DC < 12
0
- 0.020
h6
DC>12
0
- 0.030

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
a 2 flute uncoated end mill designed especially for aluminium alloys.
J100
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
C2LAD0100
C2LAD0150
C2LAD0200
C2LAD0250
C2LAD0300
C2LAD0400
C2LAD0500
C2LAD0600
C2LAD0800
C2LAD1000
C2LAD1200
C2LAD1400
C2LAD1500
C2LAD1600
C2LAD1800
C2LAD2000
1
1.5
2
2.5
3
4
5
6
8
10
12
14
15
16
18
20
4
6
9
12
20
25
30
30
40
50
50
70
70
70
70
70
40
40
40
40
60
60
70
70
90
100
110
130
130
130
140
140
4
4
4
4
6
6
6
6
8
10
12
16
16
16
20
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
2
2
2
1
1
2
1
2
CARBIDE

y Side milling
Cutting speed
Aluminium alloy
Aluminium cast
150m/min
120m/min
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
1
2
3
4
5
6
8
10
12
16
20
40000
24000
16000
12000
9500
8000
6000
4800
4000
3000
2400
320
380
510
580
640
640
770
770
770
670
610
38000
19000
13000
9500
7600
6400
4800
3800
3200
2400
1900
240
240
330
380
400
400
480
480
480
430
390
< 0.05DC
Depth of
cut
< 0.1DC
(DC < & 3)

(DC > & 3)
< 2.5DC
DC:Dia.
1) If the depth of cut is shallow, the revolution and feed rate

can be increased.
3) Climb cutting is recommended for side milling.
4) If the rigidity of the machine or the work materials
installation is very low, or chattering and noise are
generated, reduce the revolution and feed rate
proportionately.
SOLID END MILLS
Work
material
J101
C2SA
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
15
DC
SQUARE
DN
(<30HRC)
( < 45HRC)
37.5
UWC
Type1
APMX
LU
DCON(h6)
CARBIDE
DN
LF
DC < 12
0
- 0.020
h6
DC>12
0
- 0.030
DCON(h6)
BALL
DC
Type2
APMX
LU
LF
DCON=6 8<DCON<10 12<DCON<16 DCON=20

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
a High efficiency machining for aluminium alloys.
J102
Order Number
DC
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
C2SAD0300N120
C2SAD0400N120
C2SAD0500N150
C2SAD0600N160
C2SAD0800N200
C2SAD1000N300
C2SAD1000N350
C2SAD1200N300
C2SAD1200N350
C2SAD1200N400
C2SAD1600N300
C2SAD1600N400
C2SAD1600N450
C2SAD2000N400
C2SAD2000N500
3
4
5
6
8
10
10
12
12
12
16
16
16
20
20
6
6
8
8
10
12
12
15
15
15
15
15
15
20
20
12
12
15
16
20
30
35
30
35
40
30
40
45
40
50
2.7
3.7
4.7
5.7
7.4
9.4
9.4
11.4
11.4
11.4
15.4
15.4
15.4
18
18
60
60
60
75
75
75
100
75
100
125
75
100
125
100
125
6
6
6
6
8
10
10
12
12
12
16
16
16
20
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
CARBIDE

y Side milling
y Slotting
Work
material
Work
material
Aluminium alloy
Aluminium alloy
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
40000
36000
30000
27000
20000
16000
13000
10000
8000
1800
2400
3000
3200
3400
3600
3600
3600
3300
3
4
5
6
8
10
12
16
20
40000
36000
30000
27000
20000
16000
13000
10000
8000
1600
2100
2700
2800
3000
3200
3200
3200
3000
DC
< 0.5DC
Depth of
cut
Depth of
cut
< 0.8DC
DC:Dia.
< 0.8DC
DC:Dia.

If tool clamping is poor, the tool can be pulled out of the holder. Ensure that the tool is sufficiently clamped.
This table shows the cutting condition with less than 4D overhang length. If more than 4D, spindle speed, feed rate and depth of cut should
be reduced.
SOLID END MILLS
1)
2)
3)
4)
J103

CARBIDE
C2MHA
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
55
UWC
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DCON(h6)
APMX
Type1
DCON(h6)
SQUARE
DC
15
Type2
DCON(h6)
Type3
DC
LF
APMX
DC < 12
0
- 0.020
h6
DC
BALL
LF
DC>12
APMX
0
- 0.030
LF
DCON=6 8<DCON<10 12<DCON<16 20<DCON<25

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
J104
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
C2MHAD0300
C2MHAD0400
C2MHAD0500
C2MHAD0600
C2MHAD0800
C2MHAD1000
C2MHAD1200
C2MHAD1400
C2MHAD1600
C2MHAD2000
C2MHAD2500
3
4
5
6
8
10
12
14
16
20
25
9
12
15
18
20
25
25
32
32
38
38
60
60
60
60
75
75
75
75
100
125
125
6
6
6
6
8
10
12
12
16
20
25
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
2
2
2
2
3
2
2
2
CARBIDE

y Side milling
y Slotting
Work
material
Work
material
Aluminium alloy
Aluminium alloy
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
25
40000
36000
30000
27000
20000
16000
13000
10000
8000
6000
2400
2600
4000
4000
4000
4500
4500
4500
4300
3600
3
4
5
6
8
10
12
16
20
25
40000
36000
30000
27000
20000
16000
13000
10000
8000
6000
1500
1800
2800
2800
2800
3200
3200
3200
3000
2500
DC
< 0.2DC
Depth of
cut
Depth of
cut
< 1.5DC
DC:Dia.
(MAX. 20mm)
DC:Dia.

If tool clamping is poor, the tool can be pulled out of the holder. Ensure that the tool is sufficiently clamped.
SOLID END MILLS
1)
2)
3)
4)
< 1DC
J105
CARBIDE END MILLS

CARBIDE
SEE2L
(<30HRC)
( < 45HRC)
45
UWC
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
Type1
DCON(h6)
SQUARE
DC
15
APMX
DC
LF
DCON(h6)
Type2
APMX
BALL
LF
DC>12
DC < 12
0
- 0.020
h6
0
- 0.030

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
a 2 flute uncoated high helix end mill.
J106
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
SEE2030L
SEE2040L
SEE2050L
SEE2060L
SEE2070L
SEE2080L
SEE2090L
SEE2100L
SEE2110L
SEE2120L
SEE2150L
SEE2160L
SEE2200L
3
4
5
6
7
8
9
10
11
12
15
16
20
15
20
25
25
35
35
45
45
55
55
70
70
75
55
60
65
65
80
80
90
95
105
105
125
125
140
6
6
6
6
8
8
10
10
12
12
16
16
20
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
2
1
2
1
2
1
2
1
2
2
CARBIDE

Work
material

(180 280HB)

(280 380HB)
AISI 1045, AISI P20
AISI 1045, AISI P20
Pre-hardened steel
(35 45HRC)
Stainless steel
(270HB > )
Cast iron
(Tensile Strength 350MPa > )
AISI 420
AISI No 35 B
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
3400
2400
2000
1600
1200
1000
800
600
480
100
110
120
120
110
100
100
90
80
3000
2200
1800
1500
1100
880
760
560
440
40
60
60
60
60
60
70
70
80
2100
1600
1300
1000
800
640
520
400
320
20
30
40
40
40
40
40
40
40
2600
1900
1500
1300
960
760
640
480
400
40
50
50
50
50
50
60
70
70
5500
4200
3300
2800
2100
1600
1400
1000
840
160
180
200
210
210
210
210
220
230
< 0.05DC
Depth of
cut
< 2.5DC
DC:Dia.
SOLID END MILLS
1)
2)
3)
4)
J107
MSTAR END MILLS
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
15
DC
SQUARE
Hardened Steel
( < 55HRC)
45
DC < 12
0
- 0.020
h6
DC>12
0
- 0.030
APMX

0
- 0.008
0
- 0.009
0
- 0.011
Type2
Type3
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DCON(h6)
(<30HRC)
( < 45HRC)
MS
UWC
DCON(h6)
MSMHZD
DCON(h6)
CARBIDE
LF
0
- 0.013
a A single end mill for both plunging and slotting.
J108
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
MSMHZDD0100
MSMHZDD0150
MSMHZDD0200
MSMHZDD0250
MSMHZDD0300
MSMHZDD0350
MSMHZDD0400
MSMHZDD0450
MSMHZDD0500
MSMHZDD0550
MSMHZDD0600
MSMHZDD0650
MSMHZDD0700
MSMHZDD0750
MSMHZDD0800
MSMHZDD0850
MSMHZDD0900
MSMHZDD0950
MSMHZDD1000
MSMHZDD1100
MSMHZDD1200
MSMHZDD1300
MSMHZDD1400
MSMHZDD1500
MSMHZDD1600
MSMHZDD2000
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
13
14
15
16
20
2
3
4
5
6
8
8
10
10
13
13
16
16
16
19
19
19
19
22
22
26
26
26
26
30
32
45
45
50
50
50
50
50
50
50
50
60
60
60
60
70
70
70
70
80
80
90
90
90
110
110
140
4
4
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
16
16
20
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
3
3
1
2
2
CARBIDE

y Side milling
y Plunging

Work Alloy steel ( 30HRC)
material
AISI 1050, AISI No 35 B,
AISI P20
Alloy steel, Tool steel, Austenitic stainless steel, Heat resistant alloys
Pre-hardened steel
Titanium alloy
AISI H13, AISI W1-10, AISI 304, AISI 306, Inconel718
AISI P21
Ti-6Al-4V
Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate Revolution Feed rate
DC (mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min)
1
19000
1.5 14000
2
11000
3
8500
4
7200
6
5300
8
4000
10
3200
12
2700
16
2000
1600
20
600
600
600
770
850
940
1010
1000
950
720
600
13000
9000
7200
5300
4400
3200
2400
1900
1600
1200
1000
<0.2DC (DC> & 3)
Depth of
cut
310
310
310
380
480
490
560
480
440
350
290
10000
7500
6000
4400
3700
2700
2000
1600
1300
1000
800
200
210
210
220
250
270
280
300
300
260
240
9500
6400
4800
3200
2400
1600
1200
950
800
600
480
65
75
75
100
130
130
120
110
90
70
60
<1.5DC
Alloy steel, Tool steel, Austenitic stainless steel,

Pre-hardened steel
Titanium alloy
AISI H13, AISI W1-10, AISI 304, AISI 306,
AISI P21
Ti-6Al-4V
Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate
DC (mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min)
1
1.5
2
3
4
6
8
10
12
16
20
13000
12000
11000
8500
7200
5300
4000
3200
2700
2000
1600
80
120
200
250
300
300
320
340
320
250
200
10000
8000
7200
5300
4400
3200
2400
1900
1600
1200
1000
50
80
140
180
210
210
220
240
220
180
140
6000
6000
6000
4200
3300
2200
1600
1300
1100
800
640
10
20
30
50
60
70
80
70
70
55
55
0.05DC
<0.2DC (DC> & 3)
<0.1DC (DC<& 3)

material
AISI P20
<0.1DC (DC<& 3)
1.5DC
<1.5DC
DC:Dia.
Depth of
cut
<1DC (DC >& 2)
<0.5DC (DC >& 2)
<0.5DC (DC< & 2)
<0.2DC (DC < & 2)
DC:Dia.
y Slotting
Alloy steel, Tool steel, Austenitic stainless steel, Heat resistant alloys
Pre-hardened steel
Titanium alloy
AISI H13, AISI W1-10, AISI 304, AISI 306, Inconel718
AISI P21
Ti-6Al-4V
Dia. Revolution Feed rate Revolution Feed rate Revolution Feed rate Revolution Feed rate
DC (mm) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min) (min-1) (mm/min)
1
13000
1.5 12000
2
11000
3
8500
4
7200
6
5300
8
4000
10
3200
12
2700
16
2000
1600
20
130
250
500
640
650
720
780
770
730
600
500
10000
8000
7200
5300
4400
3200
2400
1900
1600
1200
1000
6000
6000
6000
4200
3300
2200
1600
1300
1100
800
640
30
60
130
130
140
140
140
150
150
130
120
DC
DC
Depth of
cut
80
150
260
320
370
380
430
370
340
290
240
<1DC (DC >& 2)

<0.5DC (DC< & 2)
5700
3800
2800
1900
1400
950
720
570
480
360
290
DC
25
30
35
50
70
70
60
50
40
30
25
SOLID END MILLS

material
AISI P20
0.2DC
<0.5DC (DC >& 2)

<0.2DC (DC < & 2)
DC:Dia.
J109
MSTAR END MILLS
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
30
Copper Alloy
Aluminium Alloy
DC
SQUARE
15
BALL
APMX
0
- 0.020
h6
APMX
4<DCON<6 7<DCON<10
0
- 0.008
Type2
Type3
LF
DC
3 < DC < 12
Type1
LF
DC
APMX
DCON(h6)
(<30HRC)
( < 45HRC)
MS
UWC
DCON(h6)
MS3ES
DCON(h6)
CARBIDE
LF
0
- 0.009
Overall length 35mm

Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
a 3 flute end mill.
MS3ESD0300L35S04
MS3ESD0350L35S04
MS3ESD0400L35S04
MS3ESD0500L35S05
MS3ESD0500L35S06
MS3ESD0600L35S05
MS3ESD0600L35S06
MS3ESD0700L35S07
MS3ESD0800L35S07
MS3ESD0800L35S08
MS3ESD1000L35S07
MS3ESD1000L35S10
MS3ESD1200L35S10
3
3.5
4
5
5
6
6
7
8
8
10
10
12
3
3.5
4
5
5
6
6
6
6
6
6
6
6
35
35
35
35
35
35
35
35
35
35
35
35
35
4
4
4
5
6
5
6
7
7
8
7
10
10
3
3
3
3
3
3
3
3
3
3
3
3
3
J110
1
1
2
2
1
3
2
2
3
2
3
2
3
a
a
a
a
a
a
a
a
a
a
a
a
Overall length 45mm

DC
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
Order Number
MS3ESD0300L45S04
MS3ESD0350L45S04
MS3ESD0400L45S04
MS3ESD0500L45S06
MS3ESD0600L45S06
MS3ESD0700L45S07
MS3ESD0800L45S07
MS3ESD0800L45S08
MS3ESD1000L45S07
MS3ESD1000L45S10
MS3ESD1200L45S10
3
3.5
4
5
6
7
8
8
10
10
12
3
3.5
4
5
6
7
8
8
10
10
12
45
45
45
45
45
45
45
45
45
45
45
4
4
4
6
6
7
7
8
7
10
10
3
3
3
3
3
3
3
3
3
3
3
Type
a
a
a
a
a
a
a
a
a
a
Type
1
1
2
1
2
2
3
2
3
2
3
CARBIDE

Work
material


Pre-hardened steel

Titanium alloy
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
7
8
10
12
10000
7500
6000
5000
4500
4000
3200
2700
600
600
600
600
560
520
450
410
7000
5200
4200
3500
3000
2800
2200
1900
400
400
400
400
360
350
300
270
6000
4500
3600
3000
2700
2400
1900
1600
300
300
300
300
280
260
230
210
5000
4000
3200
2700
2300
2000
1600
1300
120
120
120
120
110
110
100
100
<0.2DC
Depth of
cut
<1DC
DC
<0.05DC
<0.2DC
<1DC
DC
<0.1DC
DC:Dia.
SOLID END MILLS
J111
SMART MIRACLE END MILLS
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
42
43.5
45
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
SQUARE
15
DC < 12
0
- 0.02
0
- 0.03
APMX

0
- 0.008
0
- 0.009
0
- 0.011
Type3
LF
0
- 0.013

a Irregular helical geometry controls the vibration.
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
h6
DC>12
Type2
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DCON(h6)
(<30HRC)
( < 45HRC)
VQ
UWC
DCON(h6)
VQMHZV
DCON(h6)
CARBIDE
VQMHZVD0100
VQMHZVD0110
VQMHZVD0120
VQMHZVD0130
VQMHZVD0140
VQMHZVD0150
VQMHZVD0160
VQMHZVD0170
VQMHZVD0180
VQMHZVD0190
VQMHZVD0200
VQMHZVD0210
VQMHZVD0220
VQMHZVD0230
VQMHZVD0240
VQMHZVD0250
VQMHZVD0260
VQMHZVD0270
VQMHZVD0280
VQMHZVD0290
VQMHZVD0300
VQMHZVD0310
VQMHZVD0320
VQMHZVD0330
VQMHZVD0340
VQMHZVD0350
VQMHZVD0360
VQMHZVD0370
VQMHZVD0380
VQMHZVD0390
VQMHZVD0400
VQMHZVD0450
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4
4.5
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
3.8
4
4.2
4.4
4.6
4.8
5
5.2
5.4
5.6
5.8
6
7
7
7
7
8
8
8
8
8
8
10
45
45
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Note) SMART MIRACLE Coating is not energized because of its nature. Therefore, an external contact (voltaic type) tool setter cannot be used.
An internal contact (non-voltaic) type or laser type tool setter is recommended to measure the length of the tool.
J112
CARBIDE
LF
DCON
Stock
VQMHZVD0500
VQMHZVD0550
VQMHZVD0600
VQMHZVD0650
VQMHZVD0700
VQMHZVD0750
VQMHZVD0800
VQMHZVD0850
VQMHZVD0900
VQMHZVD0950
VQMHZVD1000
VQMHZVD1100
VQMHZVD1200
VQMHZVD1300
VQMHZVD1400
VQMHZVD1500
VQMHZVD1600
VQMHZVD2000
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
13
14
15
16
20
10
13
13
16
16
16
19
19
19
19
22
22
26
26
26
26
30
32
50
50
60
60
60
60
70
70
70
70
80
80
90
90
90
110
110
140
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
16
16
20
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
2
1
1
1
2
1
1
1
2
1
2
3
3
1
2
2
SQUARE
APMX
BALL
DC
RADIUS
Order Number
No. of
Flutes
Unit : mm
SOLID END MILLS
TAPER
J113

CARBIDE
VQMHZV
y Side milling
The rigidity of the machine or workpiece and chip discharge are sufficient at high efficiency conditions.
The rigidity of the machine or workpiece or chip discharge is insufficient at general-purpose conditions.
High efficiency conditions

Work
material
Carbon steel, Alloy steel,

Mild steel
Pre-hardened steel,
Alloy tool steel
AISI 1045, AISI 4140, ASTM A36,

AISI 1010
AISI P21, AISI P20, AISI 4340, SKD, AISI 304, AISI 316, Ti-6Al-4V
SKT
Austenitic, Ferritic and

Martensitic stainless steels,
Titanium alloys
Hardened stainless steels,

Cobaly chromium alloy
AISI 630, AISI 631
15-5PH, 17-4PH
Dia. Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut
DC (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm)
1
1.5
2
3
4
5
6
8
10
12
16
20
100
130
150
150
150
150
150
150
150
150
150
150
32000
28000
24000
16000
12000
9500
8000
6000
4800
4000
3000
2400
720
1300
1800
1900
2000
1900
1900
1900
1700
1400
1200
970
1.5
2.25
3
4.5
6
7.5
9
12
15
18
24
30
0.2
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
80
100
120
120
120
120
120
120
120
120
120
120
25000 530
21000 630
19000 860
13000 940
9500 940
7600 960
6400 960
4800 1000
3800 910
3200 860
2400 720
1900 570
1.5
2.25
3
4.5
6
7.5
9
12
15
18
24
30
0.2
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
60
85
100
100
100
100
100
100
100
100
100
100
19000
18000
16000
11000
8000
6400
5300
4000
3200
2700
2000
1600
430
540
620
660
670
670
830
900
960
890
720
580
1.5
2.25
3
4.5
6
7.5
9
12
15
18
24
30
0.2
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
50
65
75
75
75
75
75
75
75
75
75
75
16000
14000
12000
8000
6000
4800
4000
3000
2400
2000
1500
1200
340
420
540
580
590
600
600
630
580
540
450
360
1.5
2.25
3
4.5
6
7.5
9
12
15
18
24
30
0.1
0.15
0.4
0.6
0.8
1
1.2
1.6
2
2.4
3.2
4
ae
Depth
of cut
ap
SOLID END MILLS
General-purpose conditions
Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

AISI 1010
SKT

Titanium alloys

AISI 630, AISI 631
15-5PH, 17-4PH
1
1.5
2
3
4
5
6
8
10
12
16
20
100
120
120
120
120
120
120
120
120
120
120
120
32000
25000
19000
13000
9500
7600
6400
4800
3800
3200
2400
1900
480
740
940
1000
1000
980
1000
1000
900
760
640
510
1.5
2.25
3
4.5
6
7.5
9
12
15
18
24
30
0.2
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
80
100
100
100
100
100
100
100
100
100
100
100
25000
21000
16000
11000
8000
6400
5300
4000
3200
2700
2000
1600
350
420
480
520
520
530
540
550
510
480
400
320
1.5
2.25
3
4.5
6
7.5
9
12
15
18
24
30
0.2
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
60
80
80
80
80
80
80
80
80
80
80
80
19000
17000
13000
8500
6400
5100
4200
3200
2500
2100
1600
1300
280
340
340
340
350
350
400
430
450
420
340
270
1.5
2.25
3
4.5
6
7.5
9
12
15
18
24
30
0.2
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
50
65
70
70
70
70
70
70
70
70
70
70
16000
14000
11000
7400
5600
4500
3700
2800
2200
1900
1400
1100
220
280
330
350
370
370
370
390
350
340
280
220
1.5
2.25
3
4.5
6
7.5
9
12
15
18
24
30
0.1
0.15
0.4
0.6
0.8
1
1.2
1.6
2
2.4
3.2
4
ae
Depth
of cut
ap
1) SMART MIRACLE Coating is not energized because of its nature. Therefore, an external contact (voltaic type) tool setter cannot be used.
2) Effective cutting of stainless steel, titanium alloys and heat-resistant alloys etc. can be achieved with the use of emulsion.
3) Chattering can still occur if the machine rigidity and clamping method are insufficient.
In these cases the feed and speed should be reduced proportionately.
4) When the depth of cut is smaller than shown the feed rate can be increased.
J114
CARBIDE
y Side milling
High efficiency cutting conditions

Copper, Copper alloy
Work
material
Inconel718
Dia. Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut
DC (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm)
1
1.5
2
3
4
5
6
8
10
12
16
20
120
150
180
180
180
180
180
180
180
180
180
180
38000
32000
29000
19000
14000
11000
9500
7200
5700
4800
3600
2900
860
1400
2200
2300
2300
2300
2300
2300
2100
1700
1500
1200
1.5
2.25
3
4.5
6
7.5
9
12
15
18
24
30
0.2
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
40
40
40
40
40
40
40
40
40
40
40
40
13000
8500
6400
4200
3200
2500
2100
1600
1300
1100
800
640
160
170
170
180
180
180
190
190
220
210
150
120
1.5
2.25
3
4.5
6
7.5
9
12
15
18
24
30
0.05
0.08
0.2
0.3
0.4
0.5
0.6
0.8
1
1.2
1.6
2
ae
Depth
of cut
ap
Work
material
Inconel718
1
1.5
2
3
4
5
6
8
10
12
16
20
120
140
140
140
140
140
140
140
140
140
140
140
38000
30000
22000
15000
11000
8900
7400
5600
4500
3700
2800
2200
560
890
1100
1200
1200
1200
1200
1200
1100
880
750
590
1.5
2.25
3
4.5
6
7.5
9
12
15
18
24
30
0.2
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
30
30
30
30
30
30
30
30
30
30
30
30
9500
6400
4800
3200
2400
1900
1600
1200
950
800
600
480
75
82
86
89
90
90
95
95
110
100
76
61
1.5
2.25
3
4.5
6
7.5
9
12
15
18
24
30
SOLID END MILLS
0.05
0.07
0.2
0.3
0.4
0.5
0.6
0.8
1
1.2
1.6
2
ae
Depth
of cut
ap
4) When the depth of cut is smaller than shown the revolution and feed rate can be increased.
J115

CARBIDE
VQMHZV
y Slotting

Work
material
Carbon steel, Alloy steel, Pre-hardened steel,

Hardened stainless steels, Copper, Copper alloy
Mild steel
Carbon steel, Alloy steel, Martensitic stainless steels, Cobaly chromium alloy
Alloy tool steel
Titanium alloys
AISI 1045, AISI 4140,

ASTM A36, AISI 1010
Inconel718
AISI P21, AISI P20,

AISI 4340, SKD, SKT
AISI 304, AISI 316,

Ti-6Al-4V
AISI 630, AISI 631

15-5PH, 17-4PH
Dia. Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut
DC (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm)
1
1.5
2
3
4
5
6
8
10
12
16
20
100
130
150
150
150
150
150
150
150
150
150
150
32000
28000
24000
16000
12000
9500
8000
6000
4800
4000
3000
2400
380
590
940
1100
1400
1400
1400
1300
1200
960
810
650
0.5
0.75
2
3
4
5
6
8
10
12
12
12
80
100
120
120
120
120
120
120
120
120
120
120
25000
21000
19000
13000
9500
7600
6400
4800
3800
3200
2400
1900
150
250
460
550
680
680
770
720
630
580
500
400
0.5
0.75
2
3
4
5
6
8
10
12
12
12
60
85
100
100
100
100
100
100
100
100
100
100
19000
18000
16000
11000
8000
6400
5300
4000
3200
2700
2000
1600
100
220
480
500
530
540
560
600
670
650
480
380
0.5
0.75
2
3
4
5
6
8
10
12
12
12
45 14000 80 0.3
60 12000 140 0.4
60 9500 230 1
60 6400 270 1.5
60 4800 350 2
60 3800 350 2.5
60 3200 380 3
60 2400 360 4
60 1900 310 5
60 1600 290 6
60 1200 250 8
60
950 200 10
120
150
180
180
180
180
180
180
180
180
180
180
38000
32000
29000
19000
14000
11000
9500
7200
5700
4800
3600
2900
460
670
1100
1300
1700
1700
1700
1500
1400
1200
970
780
0.5 30
0.75 30
2
30
3
30
4
30
5
30
6
30
8
30
10
30
12
30
12
30
12
30
9500
6400
4800
3200
2400
1900
1600
1200
950
800
600
480
60
80
100
120
130
130
130
140
160
150
120
90
0.2
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
DC
Depth
of cut
ap
DC:Dia.
SOLID END MILLS
Work
material

Mild steel
Alloy tool steel
Titanium alloys
AISI 1045, AISI 4140,

ASTM A36, AISI 1010
Inconel718
AISI P21, AISI P20,

AISI 4340, SKD, SKT
AISI 304, AISI 316,

Ti-6Al-4V
AISI 630, AISI 631

15-5PH, 17-4PH
1
1.5
2
3
4
5
6
8
10
12
16
20
100
100
100
100
100
100
100
100
100
100
100
100
32000
21000
16000
11000
8000
6400
5300
4000
3200
2700
2000
1600
250
290
410
500
630
630
630
550
510
430
360
290
0.5
0.75
2
3
4
5
6
8
10
12
12
12
80 25000 99 0.5 60 19000 80 0.5 45 14000 60 0.3

80 17000 130 0.75 60 13000 100 0.75 50 11000 87 0.4
80 13000 210 2
60 9500 190 2
50 8000 130 1
80 8500 240 3
60 6400 190 3
50 5300 150 1.5
80 6400 300 4
60 4800 210 4
50 4000 190 2
80 5100 300 5
60 3800 210 5
50 3200 190 2.5
80 4200 330 6
60 3200 220 6
50 2700 210 3
80 3200 320 8
60 2400 240 8
50 2000 200 4
80 2500 270 10
60 1900 260 10
50 1600 170 5
80 2100 250 12
60 1600 250 12
50 1300 150 6
80 1600 220 12
60 1200 190 12
50
990 140 8
80 1300 180 12
60
950 150 12
50
800 110 10
120
120
120
120
120
120
120
120
120
120
120
120
38000
25000
19000
13000
9500
7600
6400
4800
3800
3200
2400
1900
300
350
490
590
750
750
760
670
600
510
430
340
0.5 25
0.75 25
2
25
3
25
4
25
5
25
6
25
8
25
10
25
12
25
12
25
12
25
8000
5300
4000
2700
2000
1600
1300
990
800
660
500
400
30
40
55
64
70
71
72
78
89
84
63
50
0.2
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
DC
Depth
of cut
ap
DC:Dia.
J116
CARBIDE
y Plunging

Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

Titanium alloys
AISI 1045, AISI 4140,

ASTM A36, AISI 1010
AISI P21, AISI P20,

AISI 4340, SKD, SKT
AISI 304, AISI 316, Ti-6Al-4V AISI 630, AISI 631

15-5PH, 17-4PH

Dia. Cutting speed Revolution Feed rate Hole Depth Step Cutting speed Revolution Feed rate Hole Depth Step Cutting speed Revolution Feed rate Hole Depth Step Cutting speed Revolution Feed rate Hole Depth Step Cutting speed Revolution Feed rate Hole Depth Step
DC (mm) (mm/min) (min-1) (mm/min) ap (mm) (mm) (mm/min) (min-1) (mm/min) ap (mm) (mm) (mm/min) (min-1) (mm/min) ap (mm) (mm) (mm/min) (min-1) (mm/min) ap (mm) (mm) (mm/min) (min-1) (mm/min) ap (mm) (mm)
1
1.5
2
3
4
5
6
8
10
12
16
20
65
85
100
100
100
100
100
100
100
100
100
100
20000
18000
16000
11000
8000
6400
5300
4000
3200
2700
2000
1600
160
270
480
660
800
960
950
720
580
490
360
290
0.5
0.75
2
3
4
5
6
8
10
12
16
20
0.1
0.3
0.5
1
2
2.5
3
4
5
5
5
5
50 16000 100 0.5

60 13000 120 0.75
70 11000 200 2
70 7400 270 3
70 5600 340 4
70 4500 410 5
70 3700 440 6
70 2800 340 8
70 2200 260 10
70 1900 230 12
70 1400 170 16
70 1100 130 20
0.1
0.3
0.4
0.6
0.8
1
1.2
1.6
2.5
3
4
5
Depth
of cut
50 16000 50 0.5
60 13000 80 0.75
60 9500 90 1
60 6400 100 1.5
60 4800 100 2
60 3800 100 2.5
60 3200 100 3
60 2400 70 4
60 1900 60 5
60 1600 50 6
60 1200 40 8
60
950 30 10
0.05
0.1
0.15
0.2
0.4
0.5
0.6
0.6
0.6
0.6
0.6
0.6
30
35
40
40
40
40
40
40
40
40
40
40
9500
7400
6400
4200
3200
2500
2100
1600
1300
1100
800
640
30 0.5
40 0.75
60 1
60 1.5
60 2
60 2.5
60 3
50 4
40 5
30 6
20 8
20 10
0.05
0.1
0.1
0.2
0.4
0.5
0.6
0.6
0.6
0.6
0.6
0.6
75
100
120
120
120
120
120
120
120
120
120
120
24000
21000
19000
13000
9500
7600
6400
4800
3800
3200
2400
1900
190
320
570
780
950
1100
1200
860
680
580
430
340
0.5
0.75
2
3
4
5
6
8
10
12
16
20
0.1
0.3
0.5
1.0
2
2.5
3
4
5
5
5
5
ap
Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

Titanium alloys
AISI 1045, AISI 4140,

ASTM A36, AISI 1010
AISI P21, AISI P20,

AISI 4340, SKD, SKT

15-5PH, 17-4PH

1
1.5
2
3
4
5
6
8
10
12
16
20
Depth
of cut
65
85
100
100
100
100
100
100
100
100
100
100
20000
18000
16000
11000
8000
6400
5300
4000
3200
2700
2000
1600
160
270
480
660
800
960
950
720
580
490
360
290
0.5
0.75
2
3
4
5
6
8
10
12
16
20
0.05
0.15
0.25
0.3
0.4
0.5
0.6
0.7
0.75
0.75
0.75
0.75
50 16000 100 0.5

60 13000 120 0.75
70 11000 200 2
70 7400 270 3
70 5600 340 4
70 4500 410 5
70 3700 440 6
70 2800 340 8
70 2200 260 10
70 1900 230 12
70 1400 170 16
70 1100 130 20
0.05
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.75
0.75
0.75
0.75
50 16000 50 0.5
60 13000 80 0.75
60 9500 90 1
60 6400 100 1.5
60 4800 100 2
60 3800 100 2.5
60 3200 100 3
60 2400 70 4
60 1900 60 5
60 1600 50 6
60 1200 40 8
60
950 30 10
0.05
0.05
0.05
0.1
0.2
0.25
0.3
0.3
0.3
0.3
0.3
0.3
30
35
40
40
40
40
40
40
40
40
40
40
9500
7400
6400
4200
3200
2500
2100
1600
1300
1100
800
640
30 0.5
40 0.75
60 1
60 1.5
60 2
60 2.5
60 3
50 4
40 5
30 6
20 8
20 10
0.05
0.05
0.05
0.1
0.2
0.25
0.3
0.3
0.3
0.3
0.3
0.3
75
100
120
120
120
120
120
120
120
120
120
120
24000
21000
19000
13000
9500
7600
6400
4800
3800
3200
2400
1900
190
320
570
780
950
1100
1200
860
680
580
430
340
0.5
0.75
2
3
4
5
6
8
10
12
16
20
SOLID END MILLS
0.05
0.15
0.25
0.3
0.4
0.5
0.6
0.7
0.75
0.75
0.75
0.75
ap
J117
VQMHZVOH
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
SQUARE
BALL
APMX
DC < 12
0
- 0.02
Aluminium Alloy
Type1
LF
DC=16
0
- 0.03

0
- 0.008
0
- 0.009
0
- 0.011

a Excellent peformance in slotting and pocketing with oil supply from the end cutting edge.
DC
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
Order Number
VQMHZVOHD0600
VQMHZVOHD0800
VQMHZVOHD1000
VQMHZVOHD1200
VQMHZVOHD1600
6
8
10
12
16
13
19
22
26
30
60
70
80
90
110
6
8
10
12
16
3
3
3
3
3
a
a
a
a
a
Type
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
h6
J118
42
43.5
45
DC
Hardened Steel
( < 55HRC)
VQ
UWC
DCON(h6)
CARBIDE
CARBIDE

y Slotting

Work
material

Mild steel
Alloy tool steel
Titanium alloys
AISI 1045, AISI 4140,

ASTM A36, AISI 1010
Inconel718
AISI P21, AISI P20,

AISI 4340, SKD, SKT
AISI 304, AISI 316,

Ti-6Al-4V
AISI 630, AISI 631

15-5PH, 17-4PH
6
8
10
12
16
150
150
150
150
150
8000
6000
4800
4000
3000
1400 6
1300 8
1200 10
960 12
810 12
120
120
120
120
120
6400
4800
3800
3200
2400
770
720
630
580
500
6
8
10
12
12
100
100
100
100
100
5300
4000
3200
2700
2000
560
600
670
650
480
6
8
10
12
12
60
60
60
60
60
3200
2400
1900
1600
1200
380
360
310
290
250
3
4
5
6
8
180
180
180
180
180
9500
7200
5700
4800
3600
1700 6
1500 8
1400 10
1200 12
970 12
30 1600 130 1.8

30 1200 140 2.4
30 950 160 3
30 800 150 3.6
30 600 120 4.8
DC
Depth
of cut
ap
DC:Dia.
Work
material

Mild steel
Alloy tool steel
Titanium alloys
AISI 1045, AISI 4140,

ASTM A36, AISI 1010
Inconel718
AISI P21, AISI P20,

AISI 4340, SKD, SKT
AISI 304, AISI 316,

Ti-6Al-4V
AISI 630, AISI 631

15-5PH, 17-4PH
6
8
10
12
16
100
100
100
100
100
5300
4000
3200
2700
2000
630 6
550 8
510 10
430 12
360 12
80
80
80
80
80
4200
3200
2500
2100
1600
330
320
270
250
220
6
8
10
12
12
60
60
60
60
60
3200
2400
1900
1600
1200
220
240
260
250
190
6
8
10
12
12
50
50
50
50
50
2700
2000
1600
1300
990
210
200
170
150
140
3
4
5
6
8
120
120
120
120
120
6400
4800
3800
3200
2400
760 6
670 8
600 10
510 12
430 12
25 1300
25 990
25 800
25 660
25 500
72
78
89
84
63
1.8
2.4
3
3.6
4.8
DC
Depth
of cut
ap
SOLID END MILLS
DC:Dia.
J119

CARBIDE
VQMHZVOH
y Plunging

Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

Titanium alloys
AISI 1045, AISI 4140,

ASTM A36, AISI 1010
AISI P21, AISI P20,

AISI 4340, SKD, SKT

15-5PH, 17-4PH

6
8
10
12
16
100
100
100
100
100
5300
4000
3200
2700
2000
950
720
580
490
360
9
12
15
18
24
3
4
5
5
5
70
70
70
70
70
3700
2800
2200
1900
1400
440
340
260
230
170
9
12
15
18
24
1.2
1.6
2.5
3
4
60
60
60
60
60
Depth
of cut
3200 100 6
2400 70 8
1900 60 10
1600 50 12
1200 40 16
0.6
0.6
0.6
0.6
0.6
40
40
40
40
40
2100
1600
1300
1100
800
60
50
40
30
20
6
8
10
12
16
0.6
0.6
0.6
0.6
0.6
120
120
120
120
120
6400
4800
3800
3200
2400
1200
860
680
580
430
9
12
15
18
24
3
4
5
5
5
ap
Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

Titanium alloys
AISI 1045, AISI 4140,

ASTM A36, AISI 1010
AISI P21, AISI P20,

AISI 4340, SKD, SKT

15-5PH, 17-4PH

SOLID END MILLS
6
8
10
12
16
Depth
of cut
100
100
100
100
100
5300
4000
3200
2700
2000
950
720
580
490
360
9
12
15
18
24
0.6
0.7
0.75
0.75
0.75
70
70
70
70
70
3700
2800
2200
1900
1400
440
340
260
230
170
9
12
15
18
24
0.6
0.7
0.75
0.75
0.75
60
60
60
60
60
3200 100 6
2400 70 8
1900 60 10
1600 50 12
1200 40 16
0.3
0.3
0.3
0.3
0.3
40
40
40
40
40
2100
1600
1300
1100
800
60
50
40
30
20
6
8
10
12
16
0.3
0.3
0.3
0.3
0.3
120
120
120
120
120
6400
4800
3800
3200
2400
1200
860
680
580
430
9
12
15
18
24
0.6
0.7
0.75
0.75
0.75
ap
J120
MIRACLE END MILL FOR DIFFICULT TO CUT MATERIALS
Titanium Alloy,
DC > 20
Copper Alloy
Aluminium Alloy
15
APMX
Type1
Type2
Type3
DC
LF
APMX
SQUARE
DC < 18
Austenitic
Stainless Steel
DCON(h6)
Hardened Steel
(>55HRC)
CARBIDE
DC
Hardened Steel
( < 55HRC)
50
DCON(h6)
(<30HRC)
( < 45HRC)
VC
UWC
DCON(h6)
VCMH
End mill, Medium cut length, 3 4 flute, High helix angle
0
- 0.020
h6
DC>12
0
- 0.030
APMX
LF

0
- 0.008
0
- 0.009
0
- 0.011
BALL
DC < 12
DC
LF
0
- 0.013
APMX
LF
DCON
Stock
VCMHD0300
VCMHD0400
VCMHD0500
VCMHD0600
VCMHD0700
VCMHD0800
VCMHD0900
VCMHD1000
VCMHD1100
VCMHD1200
VCMHD1300
VCMHD1400
VCMHD1500
VCMHD1600
VCMHD1800
VCMHD2000
VCMHD2500
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
20
25
8
11
13
13
16
19
19
22
22
26
26
26
30
32
32
38
45
45
45
50
50
60
60
70
70
75
75
75
75
80
90
90
100
120
6
6
6
6
8
8
10
10
12
12
12
12
16
16
16
20
25
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
2
1
2
1
2
1
2
3
3
1
2
3
2
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 3 4 flute end mill for milling difficult-to-cut and soft materials.
J121

CARBIDE
VCMH
Work
material

Pre-hardened steel

Titanium alloy
AISI 1050, AISI No 35 B, AISI P20,

AISI P21
AISI H13
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
18
20
25
5300
4400
3600
3200
2400
1900
1600
1200
1100
960
760
130
220
260
280
300
290
250
180
170
190
150
4400
3700
3000
2700
2000
1600
1300
1000
900
800
640
100
160
190
200
210
210
170
130
120
140
110
2400
2000
1700
1500
1200
960
800
600
530
480
380
50
80
100
100
110
115
95
70
65
75
60
1500
1300
1100
1000
800
640
530
400
350
320
260
25
40
50
50
45
45
40
30
25
25
20
Depth of
cut
< 0.2DC
< 0.05DC
< 1.5DC
< 1DC
DC
DC
< 0.5DC
< 0.3DC
(DC < &18)

(DC > &18)
< 0.05DC
SOLID END MILLS
DC:Dia.
J122
2) The above table shows cutting conditions for side milling. For slotting, please set the revolution at 80 100% and the feed rate at 60 80%
of the table figure. Please set the revolution rate at 60% and the feed rate at 40% when slotting austenitic stainless steels.
CARBIDE END MILLS
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
APMX
h6
DC>12
0
- 0.030

0
- 0.008
0
- 0.009
APMX
0
- 0.011
Type3
LF
DC
DC < 12
0
- 0.020
Type2
LF
DC
APMX
Type1
SQUARE
Austenitic
Stainless Steel
BALL
Hardened Steel
(>55HRC)
DCON(h6)
Hardened Steel
( < 55HRC)
CARBIDE
DCON(h6)
(<30HRC)
( < 45HRC)
50
UWC
DCON(h6)
CMH
LF
DC
APMX
LF
DCON
Stock
CMHD0600
CMHD0700
CMHD0800
CMHD0900
CMHD1000
CMHD1100
CMHD1200
CMHD1300
CMHD1400
CMHD1500
CMHD1600
6
7
8
9
10
11
12
13
14
15
16
13
16
19
19
22
22
26
26
26
30
32
50
60
60
70
70
75
75
75
75
80
90
6
8
8
10
10
12
12
12
12
16
16
3
3
3
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
a
Type
2
1
2
1
2
1
2
3
3
1
2
TAPER
Order Number
No. of
Flutes
Unit : mm
SOLID END MILLS
general use and cast iron milling.
RADIUS
a 3 flute ultra micro-grain uncoated carbide end mill for
J123

CARBIDE
C3SA
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Non-center Cutting
Austenitic
Stainless Steel
Titanium Alloy,
Center Cutting
Copper Alloy
Aluminium Alloy
DC
SQUARE
DN
(<30HRC)
( < 45HRC)
37.5
UWC
DCON(h6)
Type1
APMX
LU
DC < 12
0
- 0.020
h6
Type2
DCON(h6)
BALL
DC
LF
APMX
DC>12
LF
0
- 0.030
8<DCON<10 12<DCON<16 20<DCON<25

0
- 0.009
0
- 0.011
0
- 0.013
J124
DC
APMX
LU
DN
LF
DCON
Stock
C3SAD1000A100S08
C3SAD1000N300
C3SAD1000N350
C3SAD1200A150S10
C3SAD1200N300
C3SAD1200N350
C3SAD1200N400
C3SAD1600A200S14
C3SAD1600N300
C3SAD1600N400
C3SAD1600N450
C3SAD1700A150S16
C3SAD1800A200S16
C3SAD2000A200S18
C3SAD2000N400
C3SAD2000N600
C3SAD2000N850
C3SAD2500N500
C3SAD2500N650
C3SAD2500N900
C3SAD2600A200S25
10
10
10
12
12
12
12
16
16
16
16
17
18
20
20
20
20
25
25
25
26
12
12
12
15
15
15
15
15
15
15
15
18
18
20
20
20
20
20
20
20
20
30
35
30
35
40
30
40
45
40
60
85
50
65
90
9.4
9.4
11.4
11.4
11.4
15.4
15.4
15.4
18
18
18
23
23
23
100
75
100
150
75
100
125
200
75
100
125
150
200
200
100
125
150
100
125
150
200
8
10
10
10
12
12
12
14
16
16
16
16
16
18
20
20
20
25
25
25
25
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
1
1
2
1
1
1
2
1
1
1
2
2
2
1
1
1
1
1
1
2
Center
cutting edge
Order Number
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
Unit : mm
u
u
u
CARBIDE

y Side milling
y Slotting
Work
material
Work
material
Aluminium alloy
Aluminium alloy
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
12
16
18
20
25
13000
10000
9000
8000
6000
5400
5400
5000
5000
4500
12
16
18
20
25
13000
10000
9000
8000
6000
3200
3200
3000
3000
2800
DC
< 0.3DC
Depth of
cut
Depth of
cut
< 0.8DC
DC:Dia.
< 0.5DC
DC:Dia.
SOLID END MILLS

3) This table shows the cutting condition with less than 4D overhang length. If more than 4D, spindle speed, feed rate and depth of cut should
be reduced.
4) These end mills do not have a centre cutting edge, therefore when entering a workpiece use a ramping process rather than vertical feed.
feed rate proportionately, or set the depth of cut smaller.
J125
MSTAR END MILLS
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
45
Copper Alloy
Aluminium Alloy
DC
SQUARE
15
DC < 12
0
- 0.020
h6
DC>12
0
- 0.030
APMX

0
- 0.008
0
- 0.009
0
- 0.011
Type2
Type3
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DCON(h6)
(<30HRC)
( < 45HRC)
MS
UWC
DCON(h6)
MSSHD
DCON(h6)
CARBIDE
LF
0
- 0.013
a 4 flute high power end mill.
J126
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
MSSHDD0300
MSSHDD0350
MSSHDD0400
MSSHDD0450
MSSHDD0500
MSSHDD0550
MSSHDD0600
MSSHDD0650
MSSHDD0700
MSSHDD0750
MSSHDD0800
MSSHDD0850
MSSHDD0900
MSSHDD0950
MSSHDD1000
MSSHDD1100
MSSHDD1200
MSSHDD1300
MSSHDD1400
MSSHDD1500
MSSHDD1600
MSSHDD1700
MSSHDD1800
MSSHDD1900
MSSHDD2000
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
13
14
15
16
17
18
19
20
4.5
5.3
6
6.8
7.5
8.3
9
9.8
10.5
11.3
12
12.8
13.5
14.3
15
16.5
18
19.5
21
22.5
24
25.5
27
28.5
30
45
45
45
45
50
50
50
60
60
60
60
70
70
70
70
75
75
75
90
90
90
100
100
110
110
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
16
16
16
16
16
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
3
1
1
2
3
3
1
2
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
DC < 12
0
- 0.020
h6
DC>12
0
- 0.030
APMX

0
- 0.008
0
- 0.009
0
- 0.011
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
SQUARE
Austenitic
Stainless Steel
LF
BALL
Hardened Steel
(>55HRC)
CARBIDE
DCON(h6)
Hardened Steel
( < 55HRC)
45
DCON(h6)
(<30HRC)
( < 45HRC)
MS
UWC
DCON(h6)
MSMHD
0
- 0.013
APMX
LF
DCON
Stock
MSMHDD0200
MSMHDD0210
MSMHDD0220
MSMHDD0230
MSMHDD0240
MSMHDD0250
MSMHDD0260
MSMHDD0270
MSMHDD0280
MSMHDD0290
MSMHDD0300
MSMHDD0310
MSMHDD0320
MSMHDD0330
MSMHDD0340
MSMHDD0350
MSMHDD0360
MSMHDD0370
MSMHDD0380
MSMHDD0390
MSMHDD0400
MSMHDD0410
MSMHDD0420
MSMHDD0430
MSMHDD0440
MSMHDD0450
MSMHDD0460
MSMHDD0470
MSMHDD0480
MSMHDD0490
MSMHDD0500
MSMHDD0510
MSMHDD0520
MSMHDD0530
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5
5.1
5.2
5.3
4
5
5
5
5
5
6
6
6
6
8
8
8
8
8
8
11
11
11
11
11
12
12
12
12
12
13
13
13
13
13
13
13
13
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
J127
MSTAR END MILLS
MSMHD
J128
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
MSMHDD0540
MSMHDD0550
MSMHDD0560
MSMHDD0570
MSMHDD0580
MSMHDD0590
MSMHDD0600
MSMHDD0650
MSMHDD0700
MSMHDD0750
MSMHDD0800
MSMHDD0850
MSMHDD0900
MSMHDD0950
MSMHDD1000
MSMHDD1100
MSMHDD1200S10
MSMHDD1200
MSMHDD1300
MSMHDD1400
MSMHDD1500
MSMHDD1600
MSMHDD1700
MSMHDD1800
MSMHDD1900
MSMHDD2000
MSMHDD2200
MSMHDD2500
5.4
5.5
5.6
5.7
5.8
5.9
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
12
13
14
15
16
17
18
19
20
22
25
13
13
13
13
13
13
13
16
19
19
19
19
22
22
22
26
26
26
26
30
35
35
35
40
40
45
50
55
50
50
50
50
50
50
50
60
60
60
60
70
70
70
70
75
75
75
75
90
90
90
100
100
110
110
125
125
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
10
12
12
16
16
16
16
16
20
20
20
25
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
3
2
3
1
1
2
3
3
1
2
3
2
MSSHD
MSMHD
CARBIDE

y Side milling
material
AISI P20
Hardened steel (45 55HRC) Heat resistant alloys

Pre-hardened steel

Titanium alloy
AISI H13, AISI W1-10,

AISI P21
AISI 304, AISI 306, Ti-6Al-4V AISI H13
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
8
10
12
16
20
25
15000
11000
8000
6400
5800
4400
3500
2900
2200
1800
1400
550
800
900
1000
1100
1100
1000
1000
800
750
600
10000
7400
5600
4500
3700
2800
2200
1900
1400
1100
900
340
500
540
600
640
660
640
640
500
460
400
10000
7400
5600
4500
3700
2800
2200
1900
1400
1100
900
320
480
520
580
600
600
560
530
450
440
380
6400
4800
3600
2900
2400
1800
1400
1200
900
720
570
160
250
270
300
320
330
320
320
250
230
200
4800
4000
3200
2600
2100
1600
1300
1100
800
640
510
100
170
240
240
230
220
200
170
130
100
80
Depth of
cut
0.2DC
0.1DC
0.05DC
1.5DC
1.5DC
1.5DC
DC:Dia.
y Slotting

Pre-hardened steel

Titanium alloy

AISI P21
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
8
10
12
16
20
25
12000
9000
7200
5800
5000
3700
3000
2500
2000
1600
1300
400
600
720
720
800
800
720
720
600
540
480
7000
5300
4000
3200
2700
2000
1600
1300
1000
800
640
200
300
360
360
400
400
360
360
280
250
220
7000
5300
4000
3200
2700
2000
1600
1300
1000
800
640
100
150
180
180
200
200
180
180
150
130
120
4200
3200
2400
1900
1600
1200
960
800
600
480
380
80
130
140
150
160
170
160
160
130
120
100
2300
1900
1400
1100
950
720
570
480
360
290
230
40
70
95
95
95
90
80
70
50
40
35
DC
Depth of
cut
DC
1DC
(MAX. 12mm)
SOLID END MILLS

material
AISI P20
DC
0.5DC
0.2DC
DC:Dia.
J129
MSTAR END MILLS

CARBIDE
MSJHD
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
MS
UWC
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
45
Copper Alloy
Aluminium Alloy
Type1
DCON(h6)
DC
SQUARE
15
APMX
LF
DC < 12
0
- 0.020
h6
DCON(h6)
BALL
DC
Type2
APMX
DC>12
LF
0
- 0.030

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
J130
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
MSJHDD0200
MSJHDD0250
MSJHDD0300
MSJHDD0350
MSJHDD0400
MSJHDD0450
MSJHDD0500
MSJHDD0600
MSJHDD0700
MSJHDD0800
MSJHDD0900
MSJHDD1000
MSJHDD1100
MSJHDD1200
MSJHDD1400
MSJHDD1500
MSJHDD1600
MSJHDD2000
2
2.5
3
3.5
4
4.5
5
6
7
8
9
10
11
12
14
15
16
20
8
10
12
14
16
18
20
24
25
28
32
35
35
36
42
45
48
55
60
60
60
60
60
60
60
60
80
80
90
90
100
100
110
110
125
140
6
6
6
6
6
6
6
6
8
8
10
10
12
12
16
16
16
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
1
2
1
2
1
2
1
1
2
2
CARBIDE

y Side milling
material
AISI P20

Pre-hardened steel

Titanium alloy

AISI P21
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
8
10
12
16
20
11000
8000
6200
5000
4200
3200
2500
2100
1600
1200
370
550
620
670
750
780
690
670
570
470
7000
5100
4000
3200
2600
2000
1600
1300
1000
800
230
320
350
370
400
420
410
380
320
290
7000
5100
4000
3200
2600
2000
1600
1300
1000
800
210
300
340
360
390
400
380
340
280
260
5000
3800
3000
2400
2000
1500
1200
1000
750
600
100
190
210
220
220
230
210
190
170
150
3800
2500
1900
1500
1300
960
760
640
480
380
55
80
110
110
110
100
100
80
65
50
Depth of
cut
<0.05DC
<0.02DC
2.5DC
2.5DC
DC:Dia.
SOLID END MILLS
J131
MSTAR END MILLS

CARBIDE
MS4SC
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
MS
UWC
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
30
Copper Alloy
Aluminium Alloy
Type1
DCON(h6)
DC
SQUARE
15
APMX
DC
LF
DCON(h6)
Type2
BALL
APMX
LF
1 < DC < 12
0
- 0.020
h6

0
- 0.008
0
- 0.009
0
- 0.011
J132
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
MS4SCD0100
MS4SCD0150
MS4SCD0200
MS4SCD0250
MS4SCD0300
MS4SCD0400
MS4SCD0500
MS4SCD0600
MS4SCD0800
MS4SCD1000
MS4SCD1200
1
1.5
2
2.5
3
4
5
6
8
10
12
1.5
2.3
3
3.8
4.5
6
7.5
9
12
15
18
40
40
40
40
50
50
50
50
60
70
75
4
4
4
4
6
6
6
6
8
10
12
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
2
2
2
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
APMX
h6
DC>12
0
- 0.030
APMX

0
- 0.008
0
- 0.009
0
- 0.011
Type3
LF
DC
DC < 12
0
- 0.020
Type2
LF
DC
APMX
Type1
SQUARE
Austenitic
Stainless Steel
LF
BALL
Hardened Steel
(>55HRC)
CARBIDE
DCON(h6)
Hardened Steel
( < 55HRC)
30
DCON(h6)
(<30HRC)
( < 45HRC)
MS
UWC
DCON(h6)
MS4MC
0
- 0.013
APMX
LF
DCON
Stock
MS4MCD0100
MS4MCD0150
MS4MCD0200
MS4MCD0250
MS4MCD0300
MS4MCD0350
MS4MCD0400
MS4MCD0450
MS4MCD0500
MS4MCD0550
MS4MCD0600
MS4MCD0650
MS4MCD0700
MS4MCD0750
MS4MCD0800
MS4MCD0850
MS4MCD0900
MS4MCD0950
MS4MCD1000
MS4MCD1100
MS4MCD1200
MS4MCD1400
MS4MCD1600
MS4MCD1800
MS4MCD2000
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
14
16
18
20
2.5
3.8
5
6.3
7.5
9
10
11.5
12.5
14
15
16.5
17.5
19
20
21.5
22.5
24
25
27.5
30
35
40
45
50
40
40
40
40
50
50
50
50
50
50
50
60
60
60
60
70
70
70
70
75
90
90
100
100
110
4
4
4
4
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
16
16
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
3
2
3
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
J133
MSTAR END MILLS

CARBIDE
MS4SC
MS4MC

Work Pre-hardened steel
material
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
1
1.5
2
2.5
3
4
5
6
8
10
12
16
20
40000
40000
30000
24000
20000
15000
12000
10000
8000
6400
5400
2400
1900
3000
4500
4500
3900
3500
3000
2400
2100
1500
1400
1200
550
480
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
0.80
1.00
1.00
3.00
4.00
32000
32000
24000
19000
16000
12000
9000
7000
5600
4500
3800
1200
1000
2400
3600
3600
3000
2700
2400
1800
1500
1100
950
860
120
100
0.06
0.08
0.10
0.13
0.15
0.20
0.25
0.30
0.40
0.50
0.50
0.80
1.00
< Please

for depth of cut.
Depth of
cut
<1DC
DC
< Please

for depth of cut.
SOLID END MILLS
DC:Dia.
J134
MS4JC
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
MS
UWC
30
CARBIDE
DC<3
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
DC>3
DC<3
DC>3
Copper Alloy
Aluminium Alloy
DCON(h6)
DC
Type1
APMX
DC
LF
LF
0
- 0.020
h6
BALL
DCON(h6)
Type2
APMX
1 < DC < 12
SQUARE
15

0
- 0.008
0
- 0.009
0
- 0.011
APMX
LF
DCON
Stock
MS4JCD0100
MS4JCD0150
MS4JCD0200
MS4JCD0250
MS4JCD0300
MS4JCD0400
MS4JCD0500
MS4JCD0600
MS4JCD0800
MS4JCD1000
MS4JCD1200
1
1.5
2
2.5
3
4
5
6
8
10
12
4
6
8
10
12
16
20
24
32
40
48
40
40
40
50
50
50
60
60
70
90
110
4
4
4
4
6
6
6
6
8
10
12
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
2
2
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
J135
MSTAR END MILLS

CARBIDE
MS4JC
material

Pre-hardened steel

Titanium alloy
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
1
1.5
2
2.5
3
4
5
6
8
10
12
11100
7400
5600
4500
3700
3000
2600
2300
1700
1400
1200
85
85
85
85
90
110
140
170
180
180
170
9500
6400
4800
3800
3400
2700
2300
2000
1500
1300
1100
65
90
90
90
90
90
110
140
140
140
140
8000
5300
4000
3200
2600
2100
1800
1500
1200
950
800
50
50
50
55
60
70
85
110
110
110
110
6400
4200
3200
2500
2100
1700
1500
1300
1000
800
670
35
35
35
35
35
50
55
70
70
70
70
<0.05DC
(MAX. 0.5mm)
<0.02DC
<2.5DC
Depth of
cut
DC
DC
SOLID END MILLS
<0.1DC (DC < & 2)

<0.2DC (DC >& 2)
J136
<2DC
<0.05DC
DC:Dia.
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
30
CARBIDE
Copper Alloy
DN
Hardened Steel
( < 55HRC)
MS
UWC
Aluminium Alloy
15
APMX
LU
DCON(h6)
DC
Type1
DC
DN
LF
SQUARE
MS4XL
LF
0
- 0.020
h6
BALL
1 < DC < 10
DCON(h6)
Type2
APMX
LU
4<DCON<6 8<DCON<10
0
- 0.008
0
- 0.009
APMX
LU
DN
LF
DCON
Stock
MS4XLD0100N040
MS4XLD0100N060
MS4XLD0100N080
MS4XLD0100N100
MS4XLD0100N120
MS4XLD0100N160
MS4XLD0110N060
MS4XLD0110N100
MS4XLD0110N160
MS4XLD0120N060
MS4XLD0120N080
MS4XLD0120N100
MS4XLD0120N120
MS4XLD0120N160
MS4XLD0130N060
MS4XLD0130N120
MS4XLD0130N180
MS4XLD0140N060
MS4XLD0140N080
MS4XLD0140N100
MS4XLD0140N120
MS4XLD0140N140
MS4XLD0140N160
MS4XLD0140N220
MS4XLD0150N060
MS4XLD0150N080
MS4XLD0150N100
MS4XLD0150N120
MS4XLD0150N140
MS4XLD0150N160
MS4XLD0150N180
MS4XLD0150N200
MS4XLD0160N060
MS4XLD0160N080
1
1
1
1
1
1
1.1
1.1
1.1
1.2
1.2
1.2
1.2
1.2
1.3
1.3
1.3
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
1
1
1
1
1
1
1.1
1.1
1.1
1.2
1.2
1.2
1.2
1.2
1.3
1.3
1.3
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
4
6
8
10
12
16
6
10
16
6
8
10
12
16
6
12
18
6
8
10
12
14
16
22
6
8
10
12
14
16
18
20
6
8
0.94
0.94
0.94
0.94
0.94
0.94
1.04
1.04
1.04
1.14
1.14
1.14
1.14
1.14
1.24
1.24
1.24
1.34
1.34
1.34
1.34
1.34
1.34
1.34
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.54
1.54
50
50
50
50
50
60
50
50
60
50
50
50
50
60
50
50
60
50
50
50
50
60
60
60
50
50
50
50
60
60
60
60
50
50
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
J137
MSTAR END MILLS
MS4XL
J138
Order Number
DC
APMX
LU
DN
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
MS4XLD0160N100
MS4XLD0160N120
MS4XLD0160N140
MS4XLD0160N160
MS4XLD0160N180
MS4XLD0160N200
MS4XLD0160N260
MS4XLD0170N060
MS4XLD0170N140
MS4XLD0170N240
MS4XLD0180N060
MS4XLD0180N080
MS4XLD0180N100
MS4XLD0180N120
MS4XLD0180N140
MS4XLD0180N160
MS4XLD0180N180
MS4XLD0180N200
MS4XLD0180N250
MS4XLD0190N060
MS4XLD0190N160
MS4XLD0190N280
MS4XLD0200N060
MS4XLD0200N080
MS4XLD0200N100
MS4XLD0200N120
MS4XLD0200N140
MS4XLD0200N160
MS4XLD0200N180
MS4XLD0200N200
MS4XLD0200N250
MS4XLD0200N300
MS4XLD0250N080
MS4XLD0250N120
MS4XLD0250N160
MS4XLD0250N200
MS4XLD0250N250
MS4XLD0300N080
MS4XLD0300N120
MS4XLD0300N160
MS4XLD0300N200
MS4XLD0300N250
MS4XLD0300N300
MS4XLD0350N150
MS4XLD0350N250
MS4XLD0350N350
MS4XLD0400N120
MS4XLD0400N160
MS4XLD0400N200
MS4XLD0400N250
MS4XLD0400N300
MS4XLD0400N350
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.7
1.7
1.7
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.9
1.9
1.9
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3.5
3.5
3.5
4
4
4
4
4
4
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.7
1.7
1.7
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.9
1.9
1.9
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3.5
3.5
3.5
4
4
4
4
4
4
10
12
14
16
18
20
26
6
14
24
6
8
10
12
14
16
18
20
25
6
16
28
6
8
10
12
14
16
18
20
25
30
8
12
16
20
25
8
12
16
20
25
30
15
25
35
12
16
20
25
30
35
1.54
1.54
1.54
1.54
1.54
1.54
1.54
1.64
1.64
1.64
1.74
1.74
1.74
1.74
1.74
1.74
1.74
1.74
1.74
1.84
1.84
1.84
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.4
2.4
2.4
2.4
2.4
2.9
2.9
2.9
2.9
2.9
2.9
3.4
3.4
3.4
3.9
3.9
3.9
3.9
3.9
3.9
50
50
60
60
60
60
70
50
60
70
50
50
50
50
60
60
60
60
70
50
60
70
50
50
50
50
60
60
60
60
70
70
50
50
60
60
70
50
50
60
60
70
70
60
70
80
50
60
60
70
70
80
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CARBIDE
LF
DCON
Stock
MS4XLD0400N400
MS4XLD0400N450
MS4XLD0400N500
MS4XLD0500N160
MS4XLD0500N250
MS4XLD0500N350
MS4XLD0500N500
MS4XLD0600N200
MS4XLD0600N300
MS4XLD0600N400
MS4XLD0600N500
MS4XLD0800N300
MS4XLD0800N500
MS4XLD0800N700
MS4XLD1000N400
MS4XLD1000N600
MS4XLD1000N800
4
4
4
5
5
5
5
6
6
6
6
8
8
8
10
10
10
4
4
4
5
5
5
5
6
6
6
6
8
8
8
10
10
10
40
45
50
16
25
35
50
20
30
40
50
30
50
70
40
60
80
3.9
3.9
3.9
4.9
4.9
4.9
4.9
5.85
5.85
5.85
5.85
7.85
7.85
7.85
9.7
9.7
9.7
90
90
100
60
70
80
110
80
90
100
110
90
110
130
100
120
140
6
6
6
6
6
6
6
6
6
6
6
8
8
8
10
10
10
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
SQUARE
DN
BALL
LU
RADIUS
APMX
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J139
MSTAR END MILLS

CARBIDE
MS4XL
Work material

Pre-hardened steel
Work
material

Dia. Neck length
DC (mm) LU (mm)
1.2
1.5
1.8
SOLID END MILLS
2.5
4
8
12
16
6
10
12
16
6
12
16
20
6
12
20
25
6
12
16
20
30
8
25
50
8
16
25
30
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
40000
36000
20000
10000
40000
36000
20000
12000
40000
32000
16000
10000
40000
32000
12000
7000
40000
32000
24000
12000
5000
32000
9000
2500
25000
18000
12000
7000
3000
2400
1000
500
3000
2400
1200
600
3200
2400
1100
600
3600
2800
1000
600
4000
3200
2400
1200
500
4000
1100
300
3600
2500
1700
800
0.04
0.03
0.02
0.005
0.05
0.04
0.03
0.01
0.06
0.05
0.03
0.01
0.08
0.06
0.02
0.01
0.1
0.07
0.05
0.03
0.01
0.2
0.04
0.005
0.4
0.2
0.1
0.05
Dia. Neck length

DC (mm) LU (mm)
3.5
10
15
25
35
12
20
30
40
50
16
25
35
50
20
30
40
50
30
50
70
40
60
80

Pre-hardened steel
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
20000
11000
5500
18000
12000
8000
4200
2400
14000
9500
6400
3200
11000
8000
5400
3200
8000
4000
2000
6400
3200
1600
3000
1600
800
3000
2000
1300
700
400
2700
1800
1200
600
2200
1600
1100
640
1600
800
400
1300
640
320
0.6
0.15
0.06
1
0.5
0.2
0.08
0.03
1
0.5
0.2
0.05
1.2
0.6
0.25
0.15
1.6
0.5
0.2
2
0.6
0.3
DC
Depth of cut
< ap
DC:Dia.
J140
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
APMX
Type1
Type2
Type3
DC
LF
APMX
SQUARE
Hardened Steel
(>55HRC)
CARBIDE
DCON(h6)
Hardened Steel
( < 55HRC)
30
DCON(h6)
(<30HRC)
( < 45HRC)
MS
UWC
DCON(h6)
MS4EC
h6
DC>12
DC
DC < 12
0
- 0.020
0
- 0.030
APMX
LF
4<DCON<6 7<DCON<10
0
- 0.008
BALL
LF
0
- 0.009
DC
APMX
LF
DCON
Stock
MS4ECD0300L35S04
MS4ECD0350L35S04
MS4ECD0400L35S04
MS4ECD0500L35S05
MS4ECD0500L35S06
MS4ECD0600L35S05
MS4ECD0600L35S06
MS4ECD0700L35S07
MS4ECD0800L35S07
MS4ECD0800L35S08
MS4ECD1000L35S07
MS4ECD1000L35S10
MS4ECD1200L35S10
3
3.5
4
5
5
6
6
7
8
8
10
10
12
3
3.5
4
5
5
6
6
6
6
6
6
6
6
35
35
35
35
35
35
35
35
35
35
35
35
35
4
4
4
5
6
5
6
7
7
8
7
10
10
4
4
4
4
4
4
4
4
4
4
4
4
4
1
1
2
2
1
3
2
2
3
2
3
2
3
a
a
a
a
a
a
a
a
a
a
a
a
Overall length 45mm
Type
TAPER
Order Number
No. of
Flutes
Unit : mm
SOLID END MILLS
Overall length 35mm
RADIUS
a 4 flute end mill.
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
MS4ECD0300L45S04
MS4ECD0350L45S04
MS4ECD0400L45S04
MS4ECD0500L45S06
MS4ECD0600L45S06
MS4ECD0700L45S07
MS4ECD0800L45S07
MS4ECD0800L45S08
MS4ECD1000L45S07
MS4ECD1000L45S10
MS4ECD1200L45S10
MS4ECD1400L45S10
3
3.5
4
5
6
7
8
8
10
10
12
14
3
3.5
4
5
6
7
8
8
10
10
12
14
45
45
45
45
45
45
45
45
45
45
45
45
4
4
4
6
6
7
7
8
7
10
10
10
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
2
1
2
2
3
2
3
2
3
3
J141
MSTAR END MILLS

CARBIDE
MS4EC
Work
material


Pre-hardened steel

Titanium alloy
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
7
8
10
12
14
10000
7500
6000
5000
4500
4000
3200
2700
2300
900
900
900
900
840
780
680
620
550
7000
5200
4200
3500
3000
2800
2200
1900
1600
600
600
600
600
540
520
450
410
350
6000
4500
3600
3000
2700
2400
1900
1600
1400
450
450
450
450
420
390
340
310
280
5000
4000
3200
2700
2300
2000
1600
1300
1200
180
180
180
180
160
160
140
120
120
<0.2DC
Depth of
cut
<1DC
DC
<0.05DC
<0.2DC
<1DC
DC
<0.1DC
DC:Dia.
SOLID END MILLS
J142
VF4MD
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
UWC
VF
Titanium Alloy,
35
Copper Alloy
CARBIDE
Aluminium Alloy
DCON(h6)
DC
Type1
APMX
DC
LF
0
- 0.020
h6
LF
DC>12
0
- 0.030
BALL
DCON(h6)
Type2
APMX
DC < 12
SQUARE
15

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
APMX
LF
DCON
Stock
VF4MDD0100
VF4MDD0150
VF4MDD0200
VF4MDD0250
VF4MDD0300
VF4MDD0400
VF4MDD0500
VF4MDD0600
VF4MDD0800
VF4MDD1000
VF4MDD1200
VF4MDD1600
VF4MDD2000
1
1.5
2
2.5
3
4
5
6
8
10
12
16
20
2.5
3.8
5
6.3
7.5
10
12.5
15
20
25
30
40
50
40
40
40
40
50
50
50
50
60
70
90
100
110
4
4
4
4
6
6
6
6
8
10
12
16
20
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
2
2
2
2
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 4 flute end mill suitable for high-speed machining of hardened steel.
J143

CARBIDE
VF4MD
Work
material

Pre-hardened steel
AISI H13
AISI D2
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
1
1.5
2
2.5
3
4
5
6
8
10
12
16
20
40000
40000
30000
24000
20000
15000
12000
10000
8000
6400
5400
2400
1900
3000
4500
4500
3900
3500
3000
2400
2100
1500
1400
1200
550
480
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
0.80
1.00
1.00
3.00
4.00
32000
32000
24000
19000
16000
12000
9000
7000
5600
4500
3800
1200
1000
2400
3600
3600
3000
2700
2400
1800
1400
1100
950
860
280
240
0.06
0.08
0.10
0.13
0.15
0.20
0.25
0.30
0.40
0.50
0.50
0.80
1.00
16000
10600
8100
6400
5400
4000
3200
2700
2000
1600
1300
1000
800
710
650
520
450
390
450
380
320
240
210
160
130
100
0.05
0.08
0.10
0.13
0.15
0.20
0.20
0.20
0.20
0.30
0.30
0.30
0.30
< Please

for depth of cut.
Depth of
cut
< 1DC
DC
< Please

for depth of cut.
SOLID END MILLS
DC:Dia.
J144
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
VF
UWC
Austenitic
Stainless Steel
35
38
Titanium Alloy,
CARBIDE
Copper Alloy
Aluminium Alloy
austenitic stainless steels, titanium and heat-resistant alloys,

* For
the VFMHV is recommended.
DCON(h6)
DC
Type1
APMX
DC < 12
0
- 0.020
BALL
LF
SQUARE
VF4MV
DC>12
0
- 0.030
h6
0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
DC
APMX
LF
DCON
Stock
VF4MVD0600
VF4MVD0800
VF4MVD1000
VF4MVD1200
VF4MVD1600
VF4MVD2000
6
8
10
12
16
20
15
20
25
30
40
50
50
60
70
90
100
110
6
8
10
12
16
20
4
4
4
4
4
4
Type
1
1
1
1
1
1
a
a
a
a
SOLID END MILLS

Work
material

Pre-hardened steel
AISI H13
AISI D2
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
6
8
10
12
16
20
10000
8000
6400
5400
2400
1900
2100
1500
1400
1200
550
480
0.60
0.80
1.00
1.00
3.00
4.00
7000
5600
4500
3800
1200
1000
1400
1100
950
860
280
240
0.30
0.40
0.50
0.50
0.80
1.00
2700
2000
1600
1300
1000
800
320
240
210
160
130
100
0.20
0.20
0.30
0.30
0.30
0.30
< Please

for depth of cut.
Depth of
cut
< 1DC
TAPER
Order Number
No. of
Flutes
Unit : mm
RADIUS
a An irregular helix 4 flute square end mill suitable for high-speed machining of hardened steel.
DC
< Please

for depth of cut.
DC:Dia.
1) When slotting, reduce the revolutions by 50 70% and the feed rate by 40 60%.
2) For austenitic stainless steels, titanium and heat-resistant alloys, the VFMHV is recommended.
J145
IMPACT MIRACLE END MILL FOR DIFFICULT TO CUT MATERIALS, IRREGULAR HELIX
CARBIDE
VFMHV
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
UWC
VF
43
45
42
45
DC<6
DC > 6
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
Type1
APMX
DCON(h6)
SQUARE
DC
15
LF
DCON(h6)
DC
Type2
APMX
LF
h6
DC>12
0
- 0.030

0
- 0.008
0
- 0.009
0
- 0.011
Type3
APMX
DCON(h6)
DC < 12
0
- 0.020
DC
BALL
APMX Curved edge
LF
0
- 0.013
overhang applications.
J146
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
a Vibration control end mill achieving stable machining of difficult-to-cut materials and for long
VFMHVD0200
VFMHVD0250
VFMHVD0300
VFMHVD0350
VFMHVD0400
VFMHVD0500
VFMHVD0600
VFMHVD0600A070
VFMHVD0700
VFMHVD0800
VFMHVD0800A080
VFMHVD0900
VFMHVD1000A100S08
VFMHVD1000
VFMHVD1000A100
VFMHVD1100
VFMHVD1200A110S10
VFMHVD1200
VFMHVD1200A110
VFMHVD1300
VFMHVD1400A130S12
VFMHVD1600
VFMHVD1800A150S16
VFMHVD2000
2
2.5
3
3.5
4
5
6
6
7
8
8
9
10
10
10
11
12
12
12
13
14
16
18
20
4
5
8
8
11
13
13
13
19
19
19
22
22
22
22
26
26
26
26
26
32
35
42
45
45
45
45
45
45
50
50
70
60
60
80
70
100
70
100
100
110
75
110
110
130
90
150
110
4
4
6
6
6
6
6
6
8
8
8
10
8
10
10
10
10
12
12
12
12
16
16
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
2
2
1
2
2
1
3
2
2
3
3
2
2
3
3
2
3
2
CARBIDE

y Side milling
Work
material


Pre-hardened steel

Titanium alloy

AISI P20

AISI P21
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
7
8
9
10
11
12
13
14
16
18
20
21000
15000
11000
9600
8000
6800
6000
5300
4800
4400
4000
3700
3400
3000
2700
2400
1100
1250
1400
1920
2240
1900
1680
1480
1440
1350
1250
1180
1160
1140
970
860
21000
15000
11000
9600
8000
6800
6000
5300
4800
4400
4000
3700
3400
3000
2700
2400
1100
1250
1400
1920
2240
1900
1680
1480
1440
1350
1250
1180
1160
1140
970
860
14000
10600
8000
6400
5300
4500
4000
3500
3200
2900
2700
2500
2300
2000
1800
1600
560
850
960
1020
1060
1010
960
840
770
760
760
700
640
560
550
510
9600
7400
5600
4500
3700
3200
2800
2500
2200
2000
1900
1700
1600
1400
1200
1100
310
380
400
430
440
450
450
450
440
400
380
360
350
340
340
330
4800
4200
3200
2500
2100
1800
1600
1400
1300
1200
1100
1000
900
800
700
600
130
200
220
250
250
260
260
220
210
190
180
160
140
130
110
100
Depth of
cut
< 0.2DC
< 0.1DC
< 0.05DC
< 1.5DC
< 1.5DC
< 1.5DC
DC:Dia.
Work
material


Pre-hardened steel

Titanium alloy

AISI P20

AISI P21
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
7
8
9
10
11
12
13
14
16
18
20
17000
12000
9200
7600
6400
5500
4800
4200
3800
3500
3200
2900
2700
2400
2100
1900
680
720
810
1060
1280
1210
1150
1010
910
900
900
810
760
670
670
610
10000
6900
5600
4500
3700
3200
2800
2500
2200
2000
1900
1700
1600
1400
1200
1100
400
410
490
630
740
700
670
600
530
530
530
480
450
390
380
350
9600
7400
5600
4500
3700
3200
2800
2500
2200
2000
1900
1700
1600
1400
1200
1100
310
380
400
410
440
410
390
350
350
320
300
290
290
280
270
260
4800
3200
2400
1900
1600
1400
1200
1100
1000
900
800
730
680
600
530
480
130
140
150
170
190
190
190
180
160
160
160
150
140
120
120
120
3200
2700
2000
1600
1300
1100
1000
900
800
720
660
610
570
500
440
400
80
110
120
130
160
140
130
130
130
120
110
100
90
80
70
60
DC
Depth of
cut
DC
< 1DC
SOLID END MILLS
y Slotting
DC
< 0.5DC
< 0.2DC
(MAX. 12mm)
DC:Dia.
J147
CARBIDE
VFJHV
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
UWC
VF
43.5
45
DC<6
Austenitic
Stainless Steel
Titanium Alloy,
43
45
DC>6
Copper Alloy
Aluminium Alloy
DC
SQUARE
15
DCON(h6)
Type1
APMX
DC
LF
DCON(h6)
Type2
APMX
BALL
LF
DC < 12
0
- 0.020
h6
DC>12
0
- 0.030

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
Suitable for deep machining with long axial depth of cut.
J148
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
a Impact Miracle end mill with irregular helix flutes ensures stable machining of difficult-to-cut materials.
VFJHVD0200
VFJHVD0300
VFJHVD0400
VFJHVD0500
VFJHVD0600
VFJHVD0800
VFJHVD1000
VFJHVD1200
VFJHVD1600
VFJHVD2000
2
3
4
5
6
8
10
12
16
20
8
12
16
20
24
28
35
40
55
60
60
60
60
60
60
80
90
100
125
140
6
6
6
6
6
8
10
12
16
20
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
2
2
2
2
2
2
CARBIDE

y Side milling
Work
material


Pre-hardened steel

Titanium alloy

AISI P20

AISI P21
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
8
10
12
16
20
16000
12000
9500
7600
6300
4700
3800
3100
2300
1900
530
820
950
1000
1100
1100
1000
980
810
740
10000
7600
6000
4800
4000
3000
2400
2000
1500
1200
320
470
520
550
610
630
610
580
480
430
10000
7600
6000
4800
4000
3000
2400
2000
1500
1200
300
440
510
540
600
600
570
520
420
390
7400
5600
4500
3600
3000
2200
1800
1500
1100
900
140
280
310
330
330
330
310
280
240
220
3800
2500
1900
1500
1300
960
760
640
480
380
55
80
110
110
110
100
100
80
65
50
Depth of
cut
< 0.1DC
< 0.05DC
< 0.02DC
< 2.5DC
< 2.5DC
< 2.5DC
DC:Dia.
SOLID END MILLS
J149
VFMHVCH
End mill, Medium cut length, 4 flute, Irregular helix flutes, with multiple internal through coolant holes
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
42
45
Copper Alloy
Aluminium Alloy
Type1
DC
CoolStar
END MILLS
APMX
LF
BALL
SQUARE
(<30HRC)
( < 45HRC)
VF
UWC
DCON(h6)
CARBIDE
16<DC<20
0
- 0.03
DCON=16 DCON=20
h6
0
- 0.011
0
- 0.013
TAPER
machining on difficult-to-cut materials and applications requiring long overhangs.

Order Number
DC
APMX
LF
DCON
Stock
VFMHVCHD1600
VFMHVCHD2000
16
20
35
45
90
110
16
20
4
4
a
a
Type
1
1

y Side milling
SOLID END MILLS
Unit : mm
No. of
Flutes
RADIUS
a Vibration control end mill with multiple internal through coolant holes ensures stable
Work
material
y Slotting

Titanium alloy
Inconel718
Work
material

Titanium alloy
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
16
20
2000
1600
560
510
800
600
110
100
16
20
1400
1100
170
130
Depth of
cut
< 0.1DC
< 0.05DC
0.5DC 1.5DC
0.5DC 1.5DC
DC:Dia.
DC
Depth of
cut
0.5DC 1.5DC
DC:Dia.
J150
VQMHV
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
VQ
UWC
37
40
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
DCON(h6)
DC
Type1
APMX
DC
LF
LF
APMX Curved edge
0
- 0.030

0
- 0.008
0
- 0.009
0
- 0.011
Type3
APMX
DCON(h6)
h6
DC>12
DC
DC < 12
LF
0
- 0.013
BALL
DCON(h6)
Type2
APMX
0
- 0.020
SQUARE
15
LF
DCON
2
2.5
3
3.5
4
5
6
7
8
9
9
10
10
11
11
12
12
13
13
14
14
16
18
18
20
25
4
5
8
8
11
13
13
19
19
22
22
22
22
26
26
26
26
26
26
30
32
35
40
42
45
55
45
45
45
45
45
50
50
60
60
70
75
70
100
75
100
75
110
75
110
90
130
90
100
150
110
125
4
4
6
6
6
6
6
8
8
10
8
10
8
12
10
12
10
12
12
16
12
16
16
16
20
25
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
2
1
2
1
3
2
3
1
3
2
3
3
3
1
3
2
3
3
2
2
TAPER
APMX
Stock
VQMHVD0200
VQMHVD0250
VQMHVD0300
VQMHVD0350
VQMHVD0400
VQMHVD0500
VQMHVD0600
VQMHVD0700
VQMHVD0800
VQMHVD0900
VQMHVD0900S08
VQMHVD1000
VQMHVD1000S08
VQMHVD1100
VQMHVD1100S10
VQMHVD1200
VQMHVD1200S10
VQMHVD1300
VQMHVD1300S12
VQMHVD1400
VQMHVD1400S12
VQMHVD1600
VQMHVD1800
VQMHVD1800S16
VQMHVD2000
VQMHVD2500
DC
No. of
Flutes
Order Number
Unit : mm
SOLID END MILLS
RADIUS
a Smart Miracle vibration control end mill achieving stable machining of difficult-to-cut materials and for long
J151

CARBIDE
VQMHV
End mill, Medium length of cut, 4 flute, Irregular helix flutes
y Side milling

Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

AISI 1010
SKT

Titanium alloys

AISI 630, AISI 631
15-5PH,17-4PH
2
3
4
5
6
8
10
12
16
20
25
150 24000 2400 3

150 16000 2600 4.5
150 12000 2600 6
150 9500 2600 7.5
150 8000 2600 9
150 6000 2500 12
150 4800 2300 15
150 4000 1900 18
150 3000 1600 24
150 2400 1300 30
150 1900 1100 37.5
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
120 19000 1100

120 13000 1200
120 9500 1300
120 7600 1300
120 6400 1300
120 4800 1300
120 3800 1200
120 3200 1200
120 2400 960
120 1900 760
120 1500 600
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
100 16000 830

100 11000 880
100 8000 900
100 6400 900
100 5300 1100
100 4000 1200
100 3200 1300
100 2700 1200
100 2000 960
100 1600 770
100 1300 620
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
75
75
75
75
75
75
75
75
75
75
75
12000
8000
6000
4800
4000
3000
2400
2000
1500
1200
950
720
770
790
810
810
840
770
720
600
480
380
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.4
0.6
0.8
1
1.2
1.6
2
2.4
3.2
4
5
ae
Depth
of cut
ap
SOLID END MILLS
Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

AISI 1010
SKT

Titanium alloys

AISI 630, AISI 631
15-5PH,17-4PH
2
3
4
5
6
8
10
12
16
20
25
120 19000 1300

120 13000 1400
120 9500 1400
120 7600 1400
120 6400 1400
120 4800 1300
120 3800 1200
120 3200 1000
120 2400 860
120 1900 680
120 1500 390
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
100 16000
100 11000
100 8000
100 6400
100 5300
100 4000
100 3200
100 2700
100 2000
100 1600
100 1300
630
700
700
710
710
740
680
640
530
420
340
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
80
80
80
80
80
80
80
80
80
80
80
13000
8500
6400
5100
4200
3200
2500
2100
1600
1300
1000
450
450
470
470
580
630
660
610
510
410
210
1.5
2.2
3
4.5
6
7.5
9
12
15
18
24
0.2
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
70
70
70
70
70
70
70
70
70
70
70
11000
7400
5600
4500
3700
2800
2200
1900
1400
1100
890
440
470
490
500
500
520
460
450
370
290
230
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.4
0.6
0.8
1
1.2
1.6
2
2.4
3.2
4
5
ae
Depth
of cut
ap
J152
CARBIDE
y Side milling

Work
material
Inconel718
2
3
4
5
6
8
10
12
16
20
25
180
180
180
180
180
180
180
180
180
180
180
29000
19000
14000
11000
9500
7200
5700
4800
3600
2900
2300
2900
3000
3000
3000
3000
3000
2700
2300
1900
1600
1300
3
4.5
6
7.5
9
12
15
18
24
30
37
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
40
40
40
40
40
40
40
40
40
40
40
6400
4200
3200
2500
2100
1600
1300
1100
800
640
510
230
240
240
240
250
260
290
280
200
160
130
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.2
0.3
0.4
0.5
0.6
0.8
1
1.2
1.6
2
2.5
ae
Depth
of cut
ap
Work
material
Inconel718
2
3
4
5
6
8
10
12
16
20
25
140 22000 1500

140 15000 1600
140 11000 1600
140 8900 1600
140 7400 1600
140 5600 1600
140 4500 1400
140 3700 1200
140 2800 1000
140 2200 780
140 1800 670
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
30
30
30
30
30
30
30
30
30
30
30
4800
3200
2400
1900
1600
1200
950
800
600
480
380
110
120
120
120
130
130
140
140
100
81
64
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.2
0.3
0.4
0.5
0.6
0.8
1
1.2
1.6
2
2.5
SOLID END MILLS
ae
Depth
of cut
ap
J153

CARBIDE
VQMHV
End mill, Medium length of cut, 4 flute, Irregular helix flutes
y Slotting

Work
material

Mild steel
Alloy tool steel
Titanium alloys
AISI 1045, AISI 4140,

ASTM A36, AISI 1010
Inconel718
AISI P21, AISI P20,

AISI 4340, SKD, SKT
AISI 304, AISI 316,

Ti-6Al-4V
AISI 630, AISI 631

15-5PH, 17-4PH
2
3
4
5
6
8
10
12
16
20
25
150
150
150
150
150
150
150
150
150
150
150
24000
16000
12000
9500
8000
6000
4800
4000
3000
2400
1900
1200
1500
1900
1900
1900
1700
1500
1300
1100
860
760
2
3
4
5
6
8
10
12
12
12
12
120
120
120
120
120
120
120
120
120
120
120
19000
13000
9500
7600
6400
4800
3800
3200
2400
1900
1500
610
730
910
910
1000
960
840
770
670
530
420
2
3
4
5
6
8
10
12
12
12
12
100
100
100
100
100
100
100
100
100
100
100
16000
11000
8000
6400
5300
4000
3200
2700
2000
1600
1300
640
660
700
720
740
800
900
860
640
510
420
2
3
4
5
6
8
10
12
12
12
12
60
60
60
60
60
60
60
60
60
60
60
9500
6400
4800
3800
3200
2400
1900
1600
1200
950
760
300 1
360 1.5
460 2
460 2.5
510 3
480 4
420 5
380 6
340 8
270 10
210 12
180
180
180
180
180
180
180
180
180
180
180
29000
19000
14000
11000
9500
7200
5700
4800
3600
2900
2300
1500
1700
2200
2200
2300
2000
1800
1500
1300
1000
920
2
3
4
5
6
8
10
12
12
12
12
30
30
30
30
30
30
30
30
30
30
30
4800
3200
2400
1900
1600
1200
950
800
600
480
380
130
150
170
170
180
190
210
200
150
120
100
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
DC
Depth
of cut
ap
DC:Dia.
SOLID END MILLS
Work
material

Mild steel
Alloy tool steel
Titanium alloys
AISI 1045, AISI 4140,

ASTM A36, AISI 1010
Inconel718
AISI P21, AISI P20,

AISI 4340, SKD, SKT
AISI 304, AISI 316,

Ti-6Al-4V
AISI 630, AISI 631

15-5PH, 17-4PH
2
3
4
5
6
8
10
12
16
20
25
100
100
100
100
100
100
100
100
100
100
100
16000
11000
8000
6400
5300
4000
3200
2700
2000
1600
1300
550
670
840
840
840
740
680
570
480
380
340
2
3
4
5
6
8
10
12
12
12
12
80 13000 270
80 8500 310
80 6400 410
80 5100 410
80 4200 440
80 3200 420
80 2500 360
80 2100 330
80 1600 300
80 1300 240
80 1000 180
2
3
4
5
6
8
10
12
12
12
12
60
60
60
60
60
60
60
60
60
60
60
9500
6400
4800
3800
3200
2400
1900
1600
1200
950
760
250
250
280
280
300
320
350
340
250
200
160
2
3
4
5
6
8
10
12
12
12
12
50
50
50
50
50
50
50
50
50
50
50
8000
5300
4000
3200
2700
2000
1600
1300
990
800
640
170 1
200 1.5
250 2
250 2.5
290 3
260 4
230 5
210 6
180 8
150 10
120 12
120
120
120
120
120
120
120
120
120
120
120
19000
13000
9500
7600
6400
4800
3800
3200
2400
1900
1500
650
790
1000
1000
1000
890
800
680
570
450
400
2
3
4
5
6
8
10
12
12
12
12
25
25
25
25
25
25
25
25
25
25
25
4000 74
2700 86
2000 93
1600 95
1300 96
990 100
800 120
660 110
500 84
400 68
320 50
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
DC
Depth
of cut
ap
DC:Dia.
J154
VQJHV
NEW
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
UWC
VQ
37.5
40
38
40
CARBIDE
DC>6
DC<6
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DCON(h6)
DC
Type1
LF
DC
APMX
h6
LF
BALL
DC < 12
DCON(h6)
Type2
APMX
0
- 0.020
SQUARE
15
DC>12
0
- 0.030

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
DC
APMX
LF
DCON
Stock
Type
VQJHVD0200
VQJHVD0250
VQJHVD0300
VQJHVD0350
VQJHVD0400
VQJHVD0450
VQJHVD0500
VQJHVD0600
VQJHVD0700
VQJHVD0800
VQJHVD0900
VQJHVD1000
VQJHVD1200
VQJHVD1600
VQJHVD2000
2
2.5
3
3.5
4
4.5
5
6
7
8
9
10
12
16
20
8
10
12
14
16
18
20
24
25
28
32
35
40
55
70
60
60
60
60
60
60
60
60
80
80
90
90
100
125
140
6
6
6
6
6
6
6
6
8
8
10
10
12
16
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
1
1
1
1
1
1
1
2
1
2
1
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
TAPER
Order Number
No. of
Flutes
Unit : mm
SOLID END MILLS
materials and for long overhang applications.
RADIUS
a Smart Miracle vibration control end mill achieving stable machining of difficult-to-cut
J155

CARBIDE
VQJHV
NEW

y Side milling
Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

Titanium alloys


AISI 1010
AISI P21, AISI P20, AISI 4340
SUS630, SUS631,
15-5PH, 17-4PH
2
3
4
5
6
8
10
12
16
20
130 21000 700

130 14000 960
130 10000 1000
130 8300 1100
130 6900 1200
130 5200 1200
130 4100 1100
130 3400 1100
130 2600 920
130 2100 820
5
7.5
10
12.5
15
20
25
30
40
50
0.2
0.3
0.4
0.5
0.6
0.8
1
1.2
1.6
2
100 16000 510

100 11000 680
100 8000 690
100 6400 730
100 5300 810
100 4000 840
100 3200 810
100 2700 780
100 2000 640
100 1600 570
5
7.5
10
12.5
15
20
25
30
40
50
0.2
0.3
0.4
0.5
0.6
0.8
1
1.2
1.6
2
80
80
80
80
80
80
80
80
80
80
13000
8500
6400
5100
4200
3200
2500
2100
1600
1300
390
490
540
570
630
640
590
550
450
420
5
7.5
10
12.5
15
20
25
30
40
50
0.1
0.15
0.2
0.25
0.3
0.4
0.5
0.6
0.8
1
75
75
75
75
75
75
75
75
75
75
12000
8000
6000
4800
4000
3000
2400
2000
1500
1200
360
460
510
540
600
600
570
520
420
390
5
7.5
10
12.5
15
20
25
30
40
50
0.1
0.15
0.2
0.25
0.3
0.4
0.5
0.6
0.8
1
ae
Depth
of cut
ap
Work
material
Inconel718
SOLID END MILLS
2
3
4
5
6
8
10
12
16
20
160
160
160
160
160
160
160
160
160
160
25000
17000
13000
10000
8500
6400
5100
4200
3200
2500
830
1200
1300
1300
1500
1500
1300
1300
1100
970
5
7.5
10
12.5
15
20
25
30
40
50
0.2
0.3
0.4
0.5
0.6
0.8
1
1.2
1.6
2
40
40
40
40
40
40
40
40
40
40
6400
4200
3200
2500
2100
1600
1300
1100
800
640
90
130
190
180
180
170
170
140
110
80
5
7.5
10
12.5
15
20
25
30
40
50
0.04
0.06
0.08
0.1
0.12
0.16
0.2
0.24
0.32
0.4
ae
Depth
of cut
ap
J156
NEW
Hardened Steel
(>55HRC)
CARBIDE
DC>0.4
DC<0.3
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DC
DN
Hardened Steel
( < 55HRC)
35
Aluminium Alloy
20
Type1
APMX
LU
DCON(h6)
(<30HRC)
( < 45HRC)
VQ
UWC
BALL
LF
DC < 1
0
- 0.010
DCON=4
Order Number
DC
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
Type
Unit : mm
VQXLD0020N006
VQXLD0030N009
VQXLD0030N015
VQXLD0040N010
VQXLD0040N018
VQXLD0050N015
VQXLD0050N025
VQXLD0050N030
VQXLD0060N030
VQXLD0070N035
VQXLD0080N024
VQXLD0080N030
VQXLD0080N040
VQXLD0100N050
0.2
0.3
0.3
0.4
0.4
0.5
0.5
0.5
0.6
0.7
0.8
0.8
0.8
1
0.3
0.5
0.5
0.6
0.6
0.7
0.7
0.7
0.9
1
1.2
1.2
1.2
1.5
0.6
0.9
1.5
1
1.8
1.5
2.5
3
3
3.5
2.4
3
4
5
0.18
0.28
0.28
0.37
0.37
0.47
0.47
0.47
0.57
0.67
0.77
0.77
0.77
0.96
40
40
40
40
40
40
40
40
40
40
40
40
40
40
4
4
4
4
4
4
4
4
4
4
4
4
4
4
3
3
3
4
4
4
4
4
4
4
4
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
TAPER
a The use of SMART MIRACLE Coating improves chip discharge dramatically.

a Multi-cutters at a small diameter of & 1 is realized.
RADIUS
0
- 0.005
SOLID END MILLS
h5
SQUARE
VQXL
Torque chart
Order Number
VQXLD0020N006
VQXLD0030N009
VQXLD0030N015
VQXLD0040N010
VQXLD0040N018
VQXLD0050N015
VQXLD0050N025
VQXLD0050N030
VQXLD0080N024
VQXLD0080N040
VQXLD0100N050
ISO 10664
Torque type
T4
T6
T8
T15
TS25
T40
J157

CARBIDE
VQXL
NEW

y Side milling
Work material

Austenitic stainless steels, Titanium alloys
Cobaly chromium alloy, Copper, Copper alloy
Heat resistant alloys, Pre-hardened steel, Hardened steel
AISI 1045, AISI 4140, AISI 4340, AISI 304, AISI 316, AISI 304LN, AISI
316LN, Ti-6Al-4V
Inconel718, AISI P21, AISI P20, AISI H13, AISI L6, AISI 431, AISI 420
Dia. Neck Length Cutting speed

DC (mm) LU (mm)
(m/min)
0.2
0.3
0.3
0.4
0.4
0.5
0.5
0.5
0.6
0.7
0.8
0.8
0.8
1
0.6
0.9
1.5
1.2
2
1.5
2.5
3
3
3.5
2.4
3
4
5
25
40
40
50
50
60
60
60
60
60
60
60
60
60
Revolution
(min-1)
Feed rate
(mm/min)
40000
40000
40000
40000
40000
38000
38000
38000
32000
27000
24000
24000
24000
20000
360
480
360
800
560
910
610
550
640
650
960
860
670
800
Depth of cut Depth of cut Cutting speed

ap (mm)
ae (mm)
(m/min)
0.03
0.045
0.045
0.06
0.06
0.075
0.075
0.075
0.09
0.11
0.12
0.12
0.12
0.15
0.01
0.015
0.015
0.02
0.02
0.025
0.025
0.025
0.03
0.035
0.04
0.04
0.04
0.05
20
20
20
20
20
20
20
20
20
20
20
20
20
20
Revolution
(min-1)
Feed rate
(mm/min)
32000
21000
21000
16000
16000
13000
13000
13000
10500
9100
8000
8000
8000
6500
290
250
190
320
220
310
210
180
210
200
260
230
190
210
Depth of cut Depth of cut

ap (mm)
ae (mm)
0.03
0.045
0.045
0.06
0.06
0.075
0.075
0.075
0.09
0.11
0.12
0.12
0.12
0.15
0.01
0.015
0.015
0.02
0.025
0.025
0.025
0.025
0.03
0.035
0.04
0.04
0.04
0.05
ae
Depth of cut
ap
SOLID END MILLS
y Bottom face milling
Work material

316LN, Ti-6Al-4V
Dia. Neck Length Cutting speed

DC (mm) LU (mm)
(m/min)
0.2
0.3
0.3
0.4
0.4
0.5
0.5
0.5
0.6
0.7
0.8
0.8
0.8
1
0.6
0.9
1.5
1.2
2
1.5
2.5
3
3
3.5
2.4
3
4
5
25
40
40
50
50
60
60
60
60
60
60
60
60
60
Revolution
(min-1)
Feed rate
(mm/min)
40000
40000
40000
40000
40000
38000
38000
38000
32000
27000
24000
24000
24000
20000
360
480
360
800
560
910
610
550
640
640
960
840
670
800
Depth of cut Depth of cut Cutting speed

ap (mm)
ae (mm)
(m/min)
Revolution
(min-1)
Feed rate
(mm/min)
<0.2
32000
21000
21000
16000
16000
13000
13000
13000
10500
9100
8000
8000
8000
6500
290
250
190
320
220
310
210
180
210
190
260
230
190
210
0.015
0.025
0.02
0.03
0.02
0.04
0.03
0.03
0.035
0.035
0.06
0.05
0.04
0.05
20
20
20
20
20
20
20
20
20
20
20
20
20
20
<0.3
<0.3
<0.4
<0.4
<0.5
<0.5
<0.5
<0.6
<0.7
<0.8
<0.8
<0.8
<1

ap (mm)
ae (mm)
0.015
0.025
0.02
0.03
0.02
0.04
0.03
0.03
0.035
0.035
0.06
0.05
0.04
0.05
<0.1
<0.15
<0.15
<0.2
<0.2
<0.25
<0.25
<0.25
<0.3
<0.35
<0.4
<0.4
<0.4
<0.5
ae
Depth of cut
ap
J158
CARBIDE
y Slotting
Work material
Dia. Neck Length

DC (mm) LU (mm)
0.2
0.3
0.3
0.4
0.4
0.5
0.5
0.5
0.6
0.7
0.8
0.8
0.8
1
0.6
0.9
1.5
1.2
2
1.5
2.5
3
3
3.5
2.4
3
4
5

316LN, Ti-6Al-4V
Cutting speed
(m/min)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Cutting speed
(m/min)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
20
30
30
40
40
45
45
45
45
45
45
45
45
45
30000
30000
30000
30000
30000
28000
28000
28000
24000
20000
18000
18000
18000
15000
270
360
270
600
420
670
450
390
480
480
720
650
500
600
0.03
0.045
0.045
0.06
0.06
0.075
0.075
0.075
0.09
0.11
0.12
0.12
0.12
0.15
15
14
14
15
15
15
15
15
15
15
15
15
15
15
24000
15000
15000
12000
12000
9500
9500
9500
7800
6800
6000
6000
6000
4800
220
180
140
240
170
230
150
130
160
140
190
170
140
150
0.03
0.045
0.045
0.06
0.06
0.075
0.075
0.075
0.09
0.11
0.12
0.12
0.12
0.15
DC
Depth of cut
ap
SOLID END MILLS
DC:Dia.
3) When the depth of cut is small, the feed rate can be increased.
J159
MIRACLE END MILLS
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
15
DC
SQUARE
Hardened Steel
( < 55HRC)
30
DC < 12
0
- 0.020
h6
DC>12
0
- 0.030
APMX

0
- 0.008
0
- 0.009
0
- 0.011
Type2
Type3
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DCON(h6)
(<30HRC)
( < 45HRC)
VC
UWC
DCON(h6)
VC4MC
DCON(h6)
CARBIDE
LF
0
- 0.013
J160
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VC4MCD0200
VC4MCD0250
VC4MCD0300
VC4MCD0350
VC4MCD0400
VC4MCD0450
VC4MCD0500
VC4MCD0550
VC4MCD0600
VC4MCD0650
VC4MCD0700
VC4MCD0750
VC4MCD0800
VC4MCD0850
VC4MCD0900
VC4MCD0950
VC4MCD1000
VC4MCD1050
VC4MCD1100
VC4MCD1150
VC4MCD1200
VC4MCD1250
VC4MCD1300
VC4MCD1400
VC4MCD1500
VC4MCD1600
VC4MCD1700
VC4MCD1800
VC4MCD1900
VC4MCD2000
VC4MCD2200
VC4MCD2400
VC4MCD2500
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
10.5
11
11.5
12
12.5
13
14
15
16
17
18
19
20
22
24
25
6
8
8
10
11
11
13
13
13
16
16
16
19
19
19
19
22
22
22
22
26
26
26
26
30
32
32
32
32
38
38
45
45
40
40
45
45
45
45
50
50
50
60
60
60
60
70
70
70
70
75
75
75
75
75
75
75
80
90
90
90
100
100
100
120
120
4
4
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
12
12
12
16
16
16
16
20
20
20
25
25
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
2
3
3
3
1
2
3
3
1
2
3
1
2
CARBIDE


material
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
2
2.5
3
4
5
6
8
10
12
16
20
30000
24000
20000
15000
12000
10000
8000
6400
5400
2400
1900
4500
3900
3500
3000
2400
2100
1500
1400
1200
550
480
0.18
0.25
0.30
0.40
0.50
0.60
0.80
1.00
1.00
2.00
3.00
24000
19000
16000
12000
9000
7000
5600
4500
3800
1200
1000
3600
3000
2700
2400
1800
1470
1050
950
860
120
100
0.10
0.13
0.15
0.20
0.25
0.30
0.40
0.50
0.50
0.80
1.00
< Please

for depth of cut.
Depth of
cut
< DC
DC
< Please

for depth of cut.
DC:Dia.
SOLID END MILLS
1)
2)
3)
4)
J161
MIRACLE END MILLS
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
30
Copper Alloy
Aluminium Alloy
DC
SQUARE
15
LF
DC
APMX
DC < 12
0
- 0.020
h6
DC>12
0
- 0.030
APMX
Type1
Type2
Type3
LF
DC
BALL
APMX
DCON(h6)
(<30HRC)
( < 45HRC)
VC
UWC
DCON(h6)
VC4JC
DCON(h6)
CARBIDE
LF

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
J162
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VC4JCD0300
VC4JCD0350
VC4JCD0400
VC4JCD0450
VC4JCD0500
VC4JCD0550
VC4JCD0600
VC4JCD0650
VC4JCD0700
VC4JCD0750
VC4JCD0800
VC4JCD0850
VC4JCD0900
VC4JCD0950
VC4JCD1000
VC4JCD1050
VC4JCD1100
VC4JCD1150
VC4JCD1200
VC4JCD1300
VC4JCD1400
VC4JCD1500
VC4JCD1600
VC4JCD1700
VC4JCD1800
VC4JCD1900
VC4JCD2000
VC4JCD2200
VC4JCD2400
VC4JCD2500
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
10.5
11
11.5
12
13
14
15
16
17
18
19
20
22
24
25
12
15
15
15
20
20
20
25
25
25
25
25
25
25
30
30
30
30
30
35
40
40
50
50
50
55
55
65
75
75
50
50
50
50
60
60
60
70
70
70
70
90
90
90
90
90
90
90
90
90
110
110
110
110
110
110
110
140
140
140
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
12
16
16
16
20
20
20
20
25
25
25
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
2
3
1
1
2
1
1
1
2
1
1
2
CARBIDE

Work
material


Pre-hardened steel

Titanium alloy
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
25
4200
3400
2900
2500
1900
1600
1300
1000
800
650
110
140
170
200
220
220
170
140
110
85
3400
2700
2300
2000
1500
1300
1100
820
650
520
95
110
140
170
170
170
150
110
85
70
2600
2100
1800
1500
1200
950
800
600
480
380
70
85
100
130
150
130
100
80
70
50
2100
1700
1500
1300
1000
800
670
500
400
320
50
60
70
85
85
85
70
50
40
35
< 0.05DC
(MAX. 0.5mm)
< 0.02DC
< 2.5DC
Depth of
cut
DC
(MAX. 0.3mm)
< 2DC
DC
< 0.3DC
< 0.05DC
(MAX. 3mm)
(MAX. 0.5mm)
SOLID END MILLS
DC:Dia.
3) The above table shows cutting conditions for standard side milling. For slotting, please reduce the feed rate only to 50% of the table figure.
Please set the revolution rate at 60% and the feed rate at 40% when slotting austenitic stainless steels.
J163
MIRACLE END MILL FOR HIGH HARDNESS STEEL

CARBIDE
VCMDSC
End mill, Medium cut length, 4 6 flute
(<30HRC)
( < 45HRC)
30
DC<3
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
VC
UWC
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DC=3
Aluminium Alloy
Type1
DCON(h6)
DC
SQUARE
15
APMX
BALL
LF
0.5 < DC < 3

0
- 0.020
h6
DCON=6
0
- 0.008
a Ideal for tool steel and hardened materials machining
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
VCMDSCD0050
VCMDSCD0100
VCMDSCD0150
VCMDSCD0200
VCMDSCD0250
VCMDSCD0300
0.5
1
1.5
2
2.5
3
1
2.5
4
6
8
8
45
45
45
45
45
45
6
6
6
6
6
6
4
4
4
4
4
6
SOLID END MILLS
TAPER
RADIUS
Unit : mm
J164
a
a
a
a
a
Type
1
1
1
1
1
1
CARBIDE

Work
material
Dia.
DC (mm)
0.5
1
1.5
2
3
AISI H13
AISI D2
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
40000
40000
40000
40000
34000
2000
3000
5000
5600
5600
0.03
0.05
0.08
0.10
0.15
30000
20000
18000
16000
13000
600
900
1100
1300
1600
0.02
0.03
0.05
0.06
0.09
< Please
Depth of
cut
< DC
DC:Dia.
2) The above condition are for shoulder milling. For slotting & 3 or larger diameters, set the revolution, feed rate and depth of cut at 20 40% of
the table figures.
Work
material
AISI H13
AISI D2
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
0.5
1
1.5
2
20000
15000
10000
8000
200
300
280
320
0.05
0.1
0.15
0.2
15000
11000
7500
6000
90
110
150
190
0.03
0.05
0.07
0.1
SOLID END MILLS
y Slot milling with small diameter tools
DC
Depth of
cut
Please refer to the list above

for depth of cut.
DC:Dia.
1) Air blow or oil mist is recommended for good chip evacuation.
J165
MIRACLE END CRN

CARBIDE
CRN4JC
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
UWC
CRN
Titanium Alloy,
30
Copper Alloy
Aluminium Alloy
Type1
DCON(h6)
DC
SQUARE
15
APMX
LF
DCON(h6)
DC
Type2
BALL
APMX
LF
3 < DC < 12
0
- 0.02
DCON=6 8<DCON<10 DCON=12
h6
0
- 0.008
0
- 0.009
0
- 0.011
a 4 flute end mill with CRN coating for copper electrode machining.
SOLID END MILLS
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
TAPER
RADIUS
Unit : mm
CRN4JCD0300
CRN4JCD0400
CRN4JCD0500
CRN4JCD0600
CRN4JCD0800
CRN4JCD1000
CRN4JCD1200
3
4
5
6
8
10
12
12
15
20
20
25
30
30
50
50
60
60
70
90
90
6
6
6
6
8
10
12
4
4
4
4
4
4
4
a
a
a
a
a
1
1
1
2
2
2
2

Work
material
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
10600
8000
6400
5300
4000
3200
2700
280
330
380
420
460
460
460
< 0.05DC
Depth of
cut
(MAX. 0.5mm)
< 2.5DC
DC:Dia.
J166
Type
1) If the depth of cut is shallow, the revolution and feed rate can be
increased.
3) When drilling, please set the feed rate at 1/3 or below of the table
value.
4) If the rigidity of the machine or the work materials installation is
very low, or chattering and noise are generated, reduce the
revolution and feed rate proportionately.
MIRACLE END DF
Copper Alloy
Graphite
GFRP
CFRP
Machineable
Ceramics
30
DC
15
APMX
DC
LF
Type1
Type2
LF
BALL
APMX
CARBIDE
3 < DC < 12
0
- 0.02
h6
SQUARE
Aluminium Alloy
DF
DCON(h6)
UWC
DCON(h6)
DF4JC

0
- 0.008
0
- 0.009
0
- 0.011
DC
APMX
LF
DCON
Stock
DF4JCD0300
DF4JCD0400
DF4JCD0600
DF4JCD0800
DF4JCD1000
DF4JCD1200
3
4
6
8
10
12
12
16
24
28
35
36
60
60
60
70
90
110
6
6
6
8
10
12
4
4
4
4
4
4
Type
1
1
2
2
2
2
a
a
a
a
SOLID END MILLS

Graphite
TAPER
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 4 flute end mill with original diamond coating for graphite machining.
Work material
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of Cut
(mm)
Cutting Width
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of Cut
(mm)
Cutting Width
(mm)
3
4
6
8
10
12
22000
18000
14000
10500
8700
7200
2500
2900
3200
2900
2600
2200
6
8
12
16
20
24
0.15
0.2
0.3
0.4
0.5
0.6
10600
8000
6400
4000
3200
2700
280
330
380
420
460
460
6
8
12
16
20
24
0.15
0.2
0.3
0.4
0.5
0.6
< 0.05DC
Depth of cut
< 2DC
DC:Dia.
1) When high machining accuracy is needed, or the workpiece becomes chipped, we recommend lowering the feed rate.
2) Use a milling machine dedicated for graphite.
J167
MIRACLE END DF
DF4XL
UWC
DF
30
DC<3
Aluminium Alloy
Copper Alloy
Graphite
GFRP
CFRP
Machineable
Ceramics
u
DN
DC=3
SQUARE
DC
12
Type1
DCON(h6)
CARBIDE
APMX
LU
DN
LF
DCON(h6)
DC
Type2
BALL
APMX
LU
LF
1 < DC < 12
0
- 0.02
h6

0
- 0.008
0
- 0.009
0
- 0.011
a 4 flute long neck end mill with original diamond coating for graphite machining.
J168
Order Number
DC
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
DF4XLD0100N060
DF4XLD0100N080
DF4XLD0100N100
DF4XLD0150N100
DF4XLD0150N160
DF4XLD0200N100
DF4XLD0200N160
DF4XLD0200N200
DF4XLD0300N160
DF4XLD0300N200
DF4XLD0300N300
DF4XLD0400N200
DF4XLD0400N400
DF4XLD0600N300
DF4XLD0800N300
DF4XLD1000N300
DF4XLD1200N300
1
1
1
1.5
1.5
2
2
2
3
3
3
4
4
6
8
10
12
1.5
1.5
1.5
2.3
2.3
3
3
3
4.5
4.5
4.5
6
6
9
12
15
18
6
8
10
10
16
10
16
20
16
20
30
20
40
30
30
30
30
0.94
0.94
0.94
1.44
1.44
1.9
1.9
1.9
2.9
2.9
2.9
3.9
3.9
5.85
7.85
9.7
11.7
50
50
50
60
60
60
60
60
70
70
70
80
80
70
90
90
110
4
4
4
4
4
4
4
4
4
4
4
4
4
6
8
10
12
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
CARBIDE

y Side milling
Graphite
Work material
Dia.
Neck length
DC (mm) LU (mm)
1
1.5
2
3
4
6
8
10
12
6
8
10
10
16
10
16
20
16
20
30
20
40
30
30
30
30
Revolution
(min-1)
Feed rate
(mm/min)
Depth of Cut
(mm)
Cutting Width
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of Cut
(mm)
Cutting Width
(mm)
30000
25000
22000
25000
18000
22000
19000
16000
21000
18000
14000
18000
13000
14000
10500
8700
7200
1300
1000
700
1200
800
1500
1100
800
1900
1500
1000
2400
1500
3200
2900
2600
2200
1
1
1
1.5
1.5
2
2
2
3
3
3
4
4
6
8
10
12
0.05
0.05
0.05
0.075
0.075
0.1
0.1
0.1
0.15
0.15
0.15
0.4
0.4
0.6
0.8
1.0
1.2
30000
25000
22000
21000
18000
16000
16000
16000
10600
10600
10600
8000
8000
5300
4000
3200
2650
1300
1000
700
1000
800
1100
930
800
960
890
760
1100
920
1200
1100
960
800
1
1
1
1.5
1.5
2
2
2
3
3
3
4
4
6
8
10
12
0.05
0.05
0.05
0.075
0.075
0.1
0.1
0.1
0.15
0.15
0.15
0.4
0.4
0.6
0.8
1.0
1.2
(DC < & 4)

(& 4 < DC)
< 0.05DC
< 0.1DC
< DC
DC:Dia.
SOLID END MILLS
Depth of cut
J169
MIRACLE END DF
CARBIDE
DF4XL

y Slotting
Graphite
Work material
Dia.
Neck length
DC (mm) LU (mm)
1
1.5
2
3
4
6
8
10
12
6
8
10
10
16
10
16
20
16
20
30
20
40
30
30
30
30
Revolution
(min-1)
Feed rate
(mm/min)
Depth of Cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of Cut
(mm)
30000
25000
22000
25000
18000
22000
19000
16000
21000
18000
14000
18000
13000
14000
10500
8700
7200
1000
700
500
1100
600
1200
800
600
1400
1100
700
1800
900
2300
2000
1900
1700
0.1
0.08
0.06
0.14
0.1
0.2
0.16
0.12
0.3
0.25
0.2
0.5
0.4
1.2
2.0
3.0
4.0
30000
25000
22000
21000
18000
16000
16000
16000
10600
10600
10600
8000
8000
5300
4000
3200
2650
980
700
500
750
600
820
700
600
720
670
570
820
690
900
820
720
600
0.1
0.08
0.06
0.14
0.1
0.2
0.16
0.12
0.3
0.25
0.2
0.5
0.4
1.2
2.0
3.0
4.0
DC
SOLID END MILLS
Depth of cut
J170
ap
DC:Dia.
DFC END MILLS
DFC4JC
UWC
DFC
CARBIDE
CFRP
DCON(h6)
DC
Type1
APMX
BALL
LF
6 < DC < 12
0
- 0.03
h6
SQUARE

0
- 0.008
0
- 0.009
0
- 0.011
APMX
LF
DCON
Stock
DFC4JCD0600
DFC4JCD0800
DFC4JCD1000
DFC4JCD1200
6
8
10
12
20
30
30
30
70
80
90
100
6
8
10
12
4
4
4
4
a
a
a
a
Type
1
1
1
1
Note) Please contact Mitsubishi Materials for geometries and through coolant types that are non-standard.

Work material
CFRP
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
6
8
10
12
11000
8000
6400
5300
950
780
700
650
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 4 flute end mill with original CVD diamond coating for CFRP machining.
(mm/min)
1) Cutting conditions may differ considerably due to the kind of CFRP, the rigidity of the machine, or the clamping and geometry of the
workpiece. Please use the above table as a guideline.
2) When high machining accuracy is needed or if large burrs or delamination occur, we recommend reducing the feed rate.
3) When the depth of cut is greater than 0.8DC, we recommend reducing the feed rate.
4) Please take precautions against dust.
J171
DFC END MILLS

CARBIDE
DFCJRT
UWC
DFC
CFRP
DCON(h6)
SQUARE
DC
Type1
APMX
BALL
LF
h6

0
- 0.008
0
- 0.009
0
- 0.011
a Cross-nick type end mill with original CVD diamond coating for CFRP machining.
SOLID END MILLS
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
TAPER
RADIUS
Unit : mm
DFCJRTD0600
DFCJRTD0800
DFCJRTD1000
DFCJRTD1200
6
8
10
12
20
30
30
30
70
80
90
100
6
8
10
12
10
10
12
12
a
a
a
a
Type
1
1
1
1
Note) Please contact Mitsubishi Materials for geometries and through coolant types that are non-standard.

Work material
CFRP
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
6
8
10
12
11000
8000
6400
5300
1200
1000
900
850
(mm/min)
1) Cutting conditions may differ considerably due to the kind of CFRP, the rigidity of the machine, or the clamping and geometry of the
workpiece. Please use the above table as a guideline.
2) When high machining accuracy is needed or if large burrs or delamination occur, we recommend reducing the feed rate.
3) When the depth of cut is greater than 0.8DC, we recommend reducing the feed rate.
4) Please take precautions against dust.
J172
CARBIDE END MILLS
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
APMX
h6
DC>12
0
- 0.030
APMX

0
- 0.008
0
- 0.009
0
- 0.011
Type2
LF
DC
DC < 12
0
- 0.020
Type2
LF
DC
APMX
Type1
SQUARE
Austenitic
Stainless Steel
DCON(h6)
Hardened Steel
(>55HRC)
DCON(h6)
Hardened Steel
( < 55HRC)
CARBIDE
DCON(h6)
(<30HRC)
( < 45HRC)
30
UWC
BALL
C4MC
LF
0
- 0.013
APMX
LF
DCON
Stock
C4MCD0300
C4MCD0350
C4MCD0400
C4MCD0450
C4MCD0500
C4MCD0550
C4MCD0600
C4MCD0650
C4MCD0700
C4MCD0750
C4MCD0800
C4MCD0850
C4MCD0900
C4MCD0950
C4MCD1000
C4MCD1050
C4MCD1100
C4MCD1150
C4MCD1200
C4MCD1250
C4MCD1300
C4MCD1400
C4MCD1500
C4MCD1600
C4MCD1700
C4MCD1800
C4MCD1900
C4MCD2000
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
10.5
11
11.5
12
12.5
13
14
15
16
17
18
19
20
8
10
11
11
13
13
13
16
16
16
19
19
19
19
22
22
22
22
26
26
26
26
30
32
32
32
32
38
45
45
45
45
50
50
50
60
60
60
60
70
70
70
70
75
75
75
75
75
75
75
80
90
90
90
100
100
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
12
12
12
16
16
16
16
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
2
3
3
3
1
2
3
3
1
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 4 flute uncoated center cutting end mill for general use.
J173
CARBIDE END MILLS
C4JC
u
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
SQUARE
15
h6
DC>12
0
- 0.030
APMX

0
- 0.008
0
- 0.009
DCON(h6)
DC < 12
0
- 0.020
0
- 0.011
Type2
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DCON(h6)
(<30HRC)
( < 45HRC)
30
UWC
DCON(h6)
CARBIDE
Type2
LF
0
- 0.013
a 4 flute uncoated end mill for general use.
J174
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
C4JCD0300
C4JCD0350
C4JCD0400
C4JCD0450
C4JCD0500
C4JCD0550
C4JCD0600
C4JCD0650
C4JCD0700
C4JCD0750
C4JCD0800
C4JCD0850
C4JCD0900
C4JCD0950
C4JCD1000
C4JCD1050
C4JCD1100
C4JCD1150
C4JCD1200
C4JCD1300
C4JCD1400
C4JCD1500
C4JCD1600
C4JCD1700
C4JCD1800
C4JCD1900
C4JCD2000
C4JCD2200
C4JCD2400
C4JCD2500
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
10.5
11
11.5
12
13
14
15
16
17
18
19
20
22
24
25
12
15
15
15
20
20
20
25
25
25
25
25
25
25
30
30
30
30
30
35
40
40
50
50
50
55
55
65
75
75
50
50
50
50
60
60
60
70
70
70
70
90
90
90
90
90
90
90
90
90
110
110
110
110
110
110
110
140
140
140
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
12
16
16
16
20
20
20
20
25
25
25
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
2
3
1
1
2
1
1
1
2
1
1
2
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
LF
DC
APMX
APMX
h6
DC>12
0
- 0.030
APMX

0
- 0.008
0
- 0.009
0
- 0.011
Type2
Type2
LF
DC
DC < 12
0
- 0.020
Type1
SQUARE
Austenitic
Stainless Steel
DCON(h6)
Hardened Steel
(>55HRC)
DCON(h6)
Hardened Steel
( < 55HRC)
CARBIDE
DCON(h6)
(<30HRC)
( < 45HRC)
30
UWC
BALL
C4LC
LF
0
- 0.013
APMX
LF
DCON
Stock
C4LCD0300
C4LCD0350
C4LCD0400
C4LCD0450
C4LCD0500
C4LCD0550
C4LCD0600
C4LCD0650
C4LCD0700
C4LCD0750
C4LCD0800
C4LCD0850
C4LCD0900
C4LCD0950
C4LCD1000
C4LCD1050
C4LCD1100
C4LCD1150
C4LCD1200
C4LCD1250
C4LCD1300
C4LCD1400
C4LCD1500
C4LCD1600
C4LCD1700
C4LCD1800
C4LCD1900
C4LCD2000
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
10.5
11
11.5
12
12.5
13
14
15
16
17
18
19
20
20
22
25
25
30
30
30
30
40
40
40
40
40
40
50
50
50
50
50
50
50
70
70
70
70
70
70
70
60
60
60
60
70
70
70
90
90
90
90
100
100
100
100
110
110
110
110
120
120
130
130
130
140
140
140
140
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
12
12
16
16
16
20
20
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
2
3
3
1
1
2
1
1
1
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
J175
CARBIDE END MILLS

CARBIDE
C4MC
End mill, Semi long cut length, 4 flute, Center cutting C4JC
1)
C4LC
2)

y Side milling
Work Carbon steel
material
AISI 1050
Carbon steel,
Alloy steel (20 30HRC)

Pre-hardened steel (30 45HRC) Titanium alloy
AISI 1050, AISI P20
AISI P20, AISI H13, AISI P21 AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
4100
3400
2900
2500
1900
1500
1250
940
750
150
260
290
300
300
270
230
170
140
3500
2900
2400
2100
1600
1250
1050
800
640
130
210
230
260
260
230
200
140
120
2800
2200
1800
1600
1200
950
800
600
480
100
140
150
170
160
140
120
90
75
2300
1900
1500
1300
1000
800
660
500
400
90
120
135
140
150
135
110
80
70
(C4MC)
Depth of
cut
< 0.2DC
< 1.5DC
DC:Dia.
SOLID END MILLS
1) Decrease the feed rate by 20 30% for C4JC.

2) Decrease the revolution by 20 30% and the feed rate by 40 50% for C4LC.
J176
SEE4L
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
45
UWC
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
DCON(h6)
DC
Type1
APMX
DC
LF
LF
DC < 12
h6
DC>12
BALL
DCON(h6)
Type2
APMX
0
- 0.020
SQUARE
15
0
- 0.030

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
APMX
LF
DCON
Stock
SEE4030L
SEE4040L
SEE4050L
SEE4060L
SEE4070L
SEE4080L
SEE4090L
SEE4100L
SEE4110L
SEE4120L
SEE4140L
SEE4150L
SEE4160L
SEE4180L
SEE4200L
SEE4250L
3
4
5
6
7
8
9
10
11
12
14
15
16
18
20
25
15
20
25
25
35
35
45
45
55
55
70
70
70
70
75
85
55
60
65
65
80
80
90
95
105
105
125
125
125
125
140
160
6
6
6
6
8
8
10
10
12
12
16
16
16
20
20
25
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
2
1
2
1
2
1
2
1
1
2
1
2
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 4 flute high helix end mill.
J177
CARBIDE END MILLS
SEE4L
CARBIDE

Work
material

(180 280HB)

(280 380HB)
AISI 1045, AISI P20
AISI 1045, AISI P20
Pre-hardened steel
(35 45HRC)
Stainless steel
(270HB > )
Cast iron
(Tensile Strength 350MPa > )
AISI 420
AISI No 35 B
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
14
16
18
20
25
3400
2400
2000
1600
1200
1000
800
720
600
560
480
400
150
170
180
180
170
150
150
150
140
140
120
120
3000
2200
1800
1500
1100
880
760
640
560
480
440
360
60
90
90
90
90
90
110
110
110
120
120
110
2100
1600
1300
1000
800
640
520
480
400
360
320
240
30
50
60
60
60
60
60
60
60
60
60
50
2600
1900
1500
1300
960
760
640
560
480
440
400
320
60
80
80
80
80
80
90
110
110
110
110
90
5500
4200
3300
2800
2100
1600
1400
1200
1000
960
840
680
240
270
300
320
320
320
320
320
330
330
350
330
< 0.05DC
Depth of
cut
< 2.5DC
DC:Dia.
SOLID END MILLS
1)
2)
3)
4)
J178
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
CARBIDE
Copper Alloy
Aluminium Alloy
e
Type1
DCON(h6)
DC
(<30HRC)
( < 45HRC)
38
41
UWC
APMX
DC < 12
0
- 0.020
BALL
LF
SQUARE
SEG4SA
End mill, Medium cut length, 4 flute, Irregular spiral helix angle, For aluminium alloy
DC>12
0
- 0.030
h6
0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
APMX
LF
DCON
Stock
SEG4060SA
SEG4080SA
SEG4100SA
SEG4120SA
SEG4160SA
SEG4200SA
SEG4250SA
6
8
10
12
16
20
25
14
19
24
29
38
48
59
50
60
70
75
90
110
125
6
8
10
12
16
20
25
4
4
4
4
4
4
4
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1

y Side milling
Aluminium alloy
Work Plastics
material
Pure copper
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
6
8
10
12
16
20
25
9600
7200
5800
4800
3600
2900
2300
1700
1800
1800
2000
2000
2400
2400
4800
3600
2900
2400
1800
1400
1100
840
900
910
980
980
1100
1100
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 4 flute end mill with irregular helix angle for aluminium alloy.
< 0.1DC
Depth of
cut
< 1.5DC
DC:Dia.
1) The cutting conditions above are a guide only to milling within the standard depth of cut.
J179

CARBIDE
VQSVR
NEW
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
VQ
UWC
43
44
45
DC<8
43
45
DC>8
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DC<8
DC>8
Aluminium Alloy
Type1
RE
APMX
DCON(h6)
DC
SQUARE
15
LF
LF
APMX
DCON(h6)
BALL
Type3
RE
h6
LF

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
a Achieving an excellent vibration resistance due to the adoption of irregular helix.

a Use of an asymmetric chip breaker improves fracture resistance substantially. (Compared to a conventional roughing end mill)
Order Number
DC
RE
APMX
LF
DCON
Stock
Type
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
APMX
DC
RE
DCON(h6)
DC
Type2
VQSVRD0300
VQSVRD0400
VQSVRD0500
VQSVRD0600
VQSVRD0700
VQSVRD0800
VQSVRD0900
VQSVRD1000S08
VQSVRD1000
VQSVRD1200S10
VQSVRD1200
VQSVRD1400
VQSVRD1600
VQSVRD1800
VQSVRD2000
3
4
5
6
7
8
9
10
10
12
12
14
16
18
20
0.2
0.2
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
6
8
10
12
17
17
22
22
22
27
27
27
33
33
38
60
60
60
70
80
80
90
90
90
100
100
130
125
150
140
6
6
6
6
8
8
10
8
10
10
12
12
16
16
20
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
1
1
1
2
1
2
1
3
2
3
2
3
2
3
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
J180
CARBIDE

y Side milling

Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

Titanium alloys
AISI 1045, AISI 4140, ASTM

A36, AISI 1010
AISI P21, AISI P20, AISI

4340
AISI 304, AISI 316, Ti-6Al-4V AISI 630, AISI 631,

15-5PH, 17-4PH

Dia. Cutting speed Revolution Feed rate Hole Depth Hole Depth Cutting speed Revolution Feed rate Hole Depth Hole Depth Cutting speed Revolution Feed rate Hole Depth Hole Depth Cutting speed Revolution Feed rate Hole Depth Hole Depth Cutting speed Revolution Feed rate Hole Depth Hole Depth
DC (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm)
3
4
5
6
7
8
9
10
12
14
16
18
20
150 16000 960

150 12000 960
150 9500 960
150 8000 960
150 6800 950
150 6000 1100
150 5300 1100
150 4800 1100
150 4000 960
150 3400 880
150 3000 840
150 2700 810
150 2400 760
4.5 1.5
6
2
7.5 2.5
9
3
10.5 3.5
12
4
13.5 4.5
15
5
18
6
21
7
24
8
27
9
30 10
120 13000 640

120 9500 640
120 7600 640
120 6400 680
120 5500 700
120 4800 800
120 4200 760
120 3800 760
120 3200 700
120 2700 650
120 2400 620
120 2100 590
120 1900 560
4.5 1.5
6
2
7.5 2.5
9
3
10.5 3.5
12
4
13.5 4.5
15
5
18
6
21
7
24
8
27
9
30 10
100 11000 450

100 8000 430
100 6400 440
100 5300 480
100 4500 500
100 4000 570
100 3500 570
100 3200 570
100 2700 540
100 2300 510
100 2000 500
100 1800 500
100 1600 500
4.5
6
7.5
9
10.5
12
13.5
15
18
21
24
27
30
1.5
2
2.5
3
3.5
4
4.5
5
6
7
8
9
10
75
75
75
75
75
75
75
75
75
75
75
75
75
8000
6000
4800
4000
3400
3000
2700
2400
2000
1700
1500
1300
1200
330
330
330
360
380
430
430
430
400
380
380
360
360
4.5
6
7.5
9
10.5
12
13.5
15
18
21
24
27
30
0.9
1.2
1.5
1.8
2.1
2.4
2.7
3
3.6
4.2
4.8
5.4
6
180 19000 1100 4.5 1.5

180 14000 1100 6
2
180 11000 1100 7.5 2.5
180 9500 1100 9
3
180 8200 1100 10.5 3.5
180 7200 1300 12
4
180 6400 1300 13.5 4.5
180 5700 1200 15
5
180 4800 1200 18
6
180 4100 1100 21
7
180 3600 1000 24
8
180 3200 960 27
9
180 2900 920 30 10
ae
Depth
of cut
ap
Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

Titanium alloys

A36, AISI 1010

4340

15-5PH, 17-4PH

Dia. Cutting speed Revolution Feed rate Hole Depth Hole Depth Cutting speed Revolution Feed rate Hole Depth Hole Depth Cutting speed Revolution Feed rate Hole Depth Hole Depth Cutting speed Revolution Feed rate Hole Depth Hole Depth Cutting speed Revolution Feed rate Hole Depth Hole Depth
DC (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/min) ap (mm) ae (mm)
3
4
5
6
7
8
9
10
12
14
16
18
20
120 13000 610

120 9500 610
120 7600 610
120 6400 610
120 5500 620
120 4800 720
120 4200 670
120 3800 670
120 3200 610
120 2700 560
120 2400 540
120 2100 500
120 1900 480
4.5 1.5
6
2
7.5 2.5
9
3
10.5 3.5
12
4
13.5 4.5
15
5
18
6
21
7
24
8
27
9
30 10
100 11000 430

100 8000 430
100 6400 430
100 5300 450
100 4500 480
100 4000 570
100 3500 510
100 3200 510
100 2700 470
100 2300 440
100 2000 410
100 1800 400
100 1600 380
4.5 1.5
6
2
7.5 2.5
9
3
10.5 3.5
12
4
13.5 4.5
15
5
18
6
21
7
24
8
27
9
30 10
80
80
80
80
80
80
80
80
80
80
80
80
80
8500
6400
5100
4200
3600
3200
2800
2500
2100
1800
1600
1400
1300
280
280
280
300
320
380
360
360
340
320
320
310
310
4.5
6
7.5
9
10.5
12
13.5
15
18
21
24
27
30
1.5
2
2.5
3
3.5
4
4.5
5
6
7
8
9
10
70
70
70
70
70
70
70
70
70
70
70
70
70
7400
5600
4500
3700
3200
2800
2500
2200
1900
1600
1400
1200
1100
240
240
250
270
290
340
320
310
300
280
280
270
270
4.5
6
7.5
9
10.5
12
13.5
15
18
21
24
27
30
0.9
1.2
1.5
1.8
2.1
2.4
2.7
3
3.6
4.2
4.8
5.4
6
140 15000 700

140 11000 700
140 8900 720
140 7400 720
140 6400 720
140 5600 840
140 5000 800
140 4500 790
140 3700 710
140 3200 670
140 2800 630
140 2500 600
140 2200 560
SOLID END MILLS
4.5 1.5
6
2
7.5 2.5
9
3
10.5 3.5
12
4
13.5 4.5
15
5
18
6
21
7
24
8
27
9
30 10
ae
Depth
of cut
ap
J181

CARBIDE
VQSVR
NEW
y Slotting

Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

Titanium alloys

A36, AISI 1010

4340

15-5PH, 17-4PH

Dia. Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut
DC (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm)
3
4
5
6
7
8
9
10
12
14
16
18
20
120 13000 720

120 9500 720
120 7600 720
120 6400 720
120 5500 730
120 4800 840
120 4200 810
120 3800 800
120 3200 750
120 2700 670
120 2400 620
120 2100 570
120 1900 540
3
4
5
6
7
8
9
10
12
14
16
18
20
100 11000 440

100 8000 450
100 6400 460
100 5300 460
100 4500 470
100 4000 560
100 3500 540
100 3200 520
100 2700 480
100 2300 420
100 2000 380
100 1800 380
100 1600 350
3
4
5
6
7
8
9
10
12
14
16
18
20
80
80
80
80
80
80
80
80
80
80
80
80
80
8500
6400
5100
4200
3600
3200
2800
2500
2100
1800
1600
1400
1300
340
340
300
310
330
400
350
340
340
300
290
260
260
3
4
5
6
7
8
9
10
12
14
16
18
20
60
60
60
60
60
60
60
60
60
60
60
60
60
6400
4800
3800
3200
2700
2400
2100
1900
1600
1400
1200
1100
950
250
250
230
240
250
300
260
260
260
240
220
210
190
1.5
2
2.5
3
3.5
4
4.5
5
6
7
8
9
10
150 16000 890

150 12000 900
150 9500 900
150 8000 900
150 6800 950
150 6000 1100
150 5300 1000
150 4800 1000
150 4000 940
150 3400 840
150 3000 780
150 2700 730
150 2400 680
3
4
5
6
7
8
9
10
12
14
16
18
20
DC
Depth
of cut
ap
DC:Dia.
SOLID END MILLS
Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

Titanium alloys

A36, AISI 1010

4340

15-5PH, 17-4PH

Dia. Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut Cutting speed Revolution Feed rate Depth of cut
DC (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm) (m/min) (min-1) (mm/min) ap (mm)
3
4
5
6
7
8
9
10
12
14
16
18
20
100 11000 490

100 8000 490
100 6400 490
100 5300 490
100 4500 500
100 4000 600
100 3500 540
100 3200 540
100 2700 510
100 2300 460
100 2000 410
100 1800 390
100 1600 360
3
4
5
6
7
8
9
10
12
14
16
18
20
80
80
80
80
80
80
80
80
80
80
80
80
80
8500
6400
5100
4200
3600
3200
2800
2500
2100
1800
1600
1400
1300
300
310
310
310
320
380
330
330
320
300
290
260
260
3
4
5
6
7
8
9
10
12
14
16
18
20
60
60
60
60
60
60
60
60
60
60
60
60
60
6400
4800
3800
3200
2700
2400
2100
1900
1600
1400
1200
1100
950
200
200
200
200
200
240
210
210
210
190
170
170
150
3
4
5
6
7
8
9
10
12
14
16
18
20
50
50
50
50
50
50
50
50
50
50
50
50
50
5300
4000
3200
2700
2300
2000
1800
1600
1300
1100
990
880
800
170
170
170
170
170
200
180
180
170
150
140
130
130
1.5
2
2.5
3
3.5
4
4.5
5
6
7
8
9
10
120 13000 580

120 9500 580
120 7600 580
120 6400 580
120 5500 620
120 4800 720
120 4200 650
120 3800 640
120 3200 600
120 2700 540
120 2400 500
120 2100 460
120 1900 430
3
4
5
6
7
8
9
10
12
14
16
18
20
DC
Depth
of cut
ap
DC:Dia.
4) Finishing at a faster feedrate is possible when the depth of cut is small.
J182
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
43.5
45
Copper Alloy
CARBIDE
Aluminium Alloy
Type1
DCON(h6)
DC
Hardened Steel
( < 55HRC)
VF
UWC
APMX
DC < 12
0
- 0.020
h6
BALL
LF
SQUARE
VF6MHV
DC>12
0
- 0.030

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
VF6MHVD0600
VF6MHVD0800
VF6MHVD1000
VF6MHVD1200
VF6MHVD1600
VF6MHVD2000
6
8
10
12
16
20
13
19
22
26
32
38
50
60
70
75
90
100
6
8
10
12
16
20
6
6
6
6
6
6
a
a
a
a
a
1
1
1
1
1
1
SOLID END MILLS
Type

y Side milling
Work
material

Pre-hardened steel

Titanium alloy
AISI H13, AISI W1-10, AISI P21 AISI 304, AISI 306, Ti-6Al-4V
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
6
8
10
12
16
20
10600
8000
6400
5300
4000
3200
2900
2900
2700
2700
2200
1900
8000
6000
4800
4000
3000
2400
2000
2000
2000
2000
1600
1400
2100
1600
1300
1100
800
640
320
300
260
230
180
150
Depth of
cut
TAPER
Suitable for machining of difficult-to-cut materials such as stainless steel, titanium alloy and inconel.
RADIUS
a Newly developed irregular helix 6 flute geometry reduces vibrations and achieves high efficiency machining.
< 0.1DC
< 0.05DC
< 1.5DC
< 1.5DC
DC:Dia.
J183

CARBIDE
VFSD
(<30HRC)
( < 45HRC)
30
DC<3
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
VF
UWC
Austenitic
Stainless Steel
45
DC<3
DC > 3
Titanium Alloy,
Copper Alloy
DC > 3
Aluminium Alloy
Type1
DCON(h6)
SQUARE
DC
15
APMX
LF
DCON(h6)
DC
Type2
APMX
BALL
LF
1 < DC < 12
0
- 0.02
h6

0
- 0.008
0
- 0.009
0
- 0.011
a End mill with Impact Miracle coating for high hardened materials.
J184
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VFSDD0100
VFSDD0150
VFSDD0200
VFSDD0250
VFSDD0300
VFSDD0350
VFSDD0400
VFSDD0500
VFSDD0600
VFSDD0800
VFSDD1000
VFSDD1200
1
1.5
2
2.5
3
3.5
4
5
6
8
10
12
2
3
4
5
6
7
8
10
12
16
20
24
45
45
45
45
45
45
45
50
50
60
70
75
6
6
6
6
6
6
6
6
6
8
10
12
4
4
4
4
6
6
6
6
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
2
2
2
2
Austenitic
Stainless Steel
DC<3
DC > 3
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
DC < 12
0
- 0.02
h6
DC>12
0
- 0.03
APMX
Type2
Type2
LF
DC
APMX
Type1
LF
DC
APMX
DC > 3
SQUARE
Hardened Steel
(>55HRC)
CARBIDE
LF
BALL
DC<3
Hardened Steel
( < 55HRC)
45
DCON(h6)
30
DCON(h6)
(<30HRC)
( < 45HRC)
VF
UWC
DCON(h6)
VFMD

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
APMX
LF
DCON
Stock
VFMDD0100
VFMDD0150
VFMDD0200
VFMDD0250
VFMDD0300
VFMDD0400
VFMDD0500
VFMDD0600
VFMDD0800
VFMDD1000
VFMDD1200
VFMDD1400
VFMDD1500
VFMDD1600
VFMDD1800
VFMDD2000
VFMDD2200
VFMDD2500
1
1.5
2
2.5
3
4
5
6
8
10
12
14
15
16
18
20
22
25
3.5
5
7
8
10
12
15
15
20
25
30
35
40
40
40
45
45
60
60
60
60
60
60
60
60
60
75
80
100
105
110
110
120
125
135
160
6
6
6
6
6
6
6
6
8
10
12
12
16
16
16
20
20
25
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
2
2
2
3
1
2
3
2
3
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a End mill with Impact Miracle coating for high hardened materials.
J185

CARBIDE
VFSD
VFMD
Work
material
AISI H13
AISI D2
AISI W1, AISI M2
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
1
2
3
4
6
8
10
12
16
20
25
40000
40000
32000
24000
16000
12000
9600
8000
6000
4800
3800
1200
2000
3800
4400
5800
5800
5800
4800
3600
2900
2300
0.05
0.1
0.2
0.2
0.3
0.4
0.5
0.6
0.8
1.0
1.0
40000
24000
16000
12000
8000
6000
4800
4000
3000
2400
1900
800
1000
1900
2200
2900
2900
2900
2400
1800
1400
1100
0.03
0.05
0.1
0.1
0.2
0.2
0.3
0.3
0.5
0.5
0.5
32000
16000
11000
8000
5300
4000
3200
2700
2000
1600
1300
500
600
1200
1300
1800
1800
1800
1500
1100
880
720
0.02
0.05
0.05
0.05
0.1
0.1
0.2
0.2
0.3
0.3
0.3
Depth of
cut

for depth of cut.

for depth of cut.
< 1.5DC
< 1.0DC
DC:Dia.
SOLID END MILLS
Work
material
AISI H13
AISI D2
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
1
2
15000
8000
300
320
0.1
0.2
9500
4800
110
190
0.05
0.1
DC
Depth of
cut

for depth of cut.
DC:Dia.
J186
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
CARBIDE
Copper Alloy
Aluminium Alloy
Type1
APMX
DCON(h6)
END MILLS
LF
BALL
DC < 12
43.5
45
DC
CoolStar
0
- 0.020
VF
UWC
SQUARE
VF6MHVCH
End mill, Medium cut length, Irregular helix flutes, with multiple internal through coolant holes
DC>12
0
- 0.030
DCON=10 DCON=12 DCON=16 DCON=20
h6
0
- 0.009
0
- 0.011
0
- 0.011
0
- 0.013
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
VF6MHVCHD1000
VF6MHVCHD1200
VF6MHVCHD1600
VF6MHVCHD2000
10
12
16
20
22
26
32
38
70
75
90
100
10
12
16
20
6
6
6
6
a
a
a
a
Type
1
1
1
1
TAPER
RADIUS
y Side milling
Work
material
SOLID END MILLS

y Trochoidal slotting

Titanium alloy
Inconel718
Work
material

Titanium alloy
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
10
12
16
20
4800
4000
3000
2400
2000
2000
1600
1400
1300
1100
800
640
260
230
180
150
10
12
16
20
4800
4000
3000
2400
1400
1200
1100
900
Depth of
cut
< 0.1DC
< 0.05DC
0.5DC 1.5DC
0.5DC 1.5DC
1.5DC<
< 0.1DC
Depth of
cut
DC:Dia.
0.5DC 1.5DC
DC:Dia.
J187
VCLD
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
VC
Titanium Alloy,
45
Copper Alloy
Aluminium Alloy
SQUARE
DC
UWC
Type1
DCON(h6)
CARBIDE
APMX
BALL
LF
DC>12
DC < 12
0
- 0.020
0
- 0.030
h6
0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
a Ideal for tool steel and hardened materials machining
SOLID END MILLS
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
TAPER
RADIUS
Unit : mm
VCLDD0600
VCLDD0800
VCLDD1000
VCLDD1200
VCLDD1600
VCLDD2000
VCLDD2500
6
8
10
12
16
20
25
26
36
46
56
66
76
92
70
90
100
110
130
140
180
6
8
10
12
16
20
25
6
6
6
6
6
6
6
Type
1
1
1
1
1
1
1
a
a
a
a
a
a

Work
material

Pre-hardened steel
AISI H13
AISI D2
AISI W1, AISI M2
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
6
8
10
12
16
20
25
2100
1600
1300
1100
800
640
510
450
430
420
380
310
270
230
1600
1200
960
800
600
480
380
330
310
290
260
220
190
160
1300
1000
800
660
500
400
320
240
230
220
200
160
140
120
1100
800
640
530
400
320
260
190
170
150
140
120
110
90
Depth of
cut
< 0.01DC
< 0.005DC
3DC 4DC
3DC 4DC
DC:Dia.
J188
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
45
Copper Alloy
CARBIDE
Aluminium Alloy
DC
Hardened Steel
( < 55HRC)
VC
UWC
DCON(h6)
Type1
APMX
DC>12
DC < 12
0
- 0.02
h6
BALL
LF
SQUARE
VC6MH
0
- 0.03

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
DC
APMX
LF
DCON
Stock
VC6MHD0600
VC6MHD0800
VC6MHD1000
VC6MHD1200
VC6MHD1600
VC6MHD2000
VC6MHD2500
6
8
10
12
16
20
25
13
19
22
26
32
38
45
50
60
70
75
90
100
120
6
8
10
12
16
20
25
6
6
6
6
6
6
6
Type
1
1
1
1
1
1
1
a
a
a
a
a
SOLID END MILLS

Work
material


Pre-hardened steel

Titanium alloy
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
6
8
10
12
16
20
25
10600
8000
6400
5300
4000
3200
2500
2900
2900
2700
2700
2200
1900
1600
8000
6000
4800
4000
3000
2400
1900
2000
2000
2000
2000
1600
1400
1200
4200
3200
2500
2100
1600
1300
1000
900
900
870
830
740
710
560
2100
1600
1300
1100
800
640
510
320
300
260
230
180
150
120
Depth of
cut
< 0.1DC
< 0.05DC
< 1DC
< 1DC
TAPER
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 6 flute end mill for milling difficult-to-cut and soft materials.
DC:Dia.
J189
VF8MHVCH
End mill, Medium cut length, Irregular helix flutes, with multiple internal through coolant holes
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
CoolStar
44
45
Copper Alloy
Aluminium Alloy
END MILLS
Type1
APMX
DCON(h6)
SQUARE
VF
UWC
DC
CARBIDE
BALL
LF
16<DC<20
0
- 0.03
DCON=16 DCON=20
h6
0
- 0.011
0
- 0.013
TAPER

Order Number
DC
APMX
LF
DCON
Stock
VF8MHVCHD1600
VF8MHVCHD2000
16
20
32
38
90
100
16
20
8
8
a
a
Type
1
1

y Side milling
SOLID END MILLS
Unit : mm
No. of
Flutes
RADIUS
Work
material

Titanium alloy
Inconel718
Work
material

Titanium alloy
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
16
20
3000
2400
2100
1900
800
640
240
200
16
20
3000
2400
1400
1200
Depth of
cut
< 0.08DC
< 0.05DC
0.5DC 1.5DC
0.5DC 1.5DC
1.5DC<
< 0.08DC
Depth of
cut
DC:Dia.
0.5DC 1.5DC
DC:Dia.
J190
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
45
Copper Alloy
CARBIDE
Aluminium Alloy
DC
Hardened Steel
( < 55HRC)
VC
UWC
DCON(h6)
Type1
APMX
BALL
LF
20<DC<25
0
- 0.03
h6
SQUARE
VC8MH
20<DCON<25
0
- 0.013
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
VC8MHD2000
VC8MHD2500
20
25
38
45
100
120
20
25
8
8
Type
1
1


Pre-hardened steel

Titanium alloy
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
6
8
10
12
16
20
25
10600
8000
6400
5300
4000
3200
2500
2900
2900
2700
2700
2200
1900
1600
8000
6000
4800
4000
3000
2400
1900
2000
2000
2000
2000
1600
1400
1200
4200
3200
2500
2100
1600
1300
1000
900
900
870
830
740
710
560
2100
1600
1300
1100
800
640
510
320
300
260
230
180
150
120
Depth of
cut
< 0.1DC
< 0.05DC
< 1DC
< 1DC
SOLID END MILLS
TAPER

Work
material
RADIUS
a 8 flute end mill for milling difficult-to-cut and soft materials.
DC:Dia.
J191
CBN END MILLS
GBE
CBN end mill, Single flute
CBN
PCD
Light Alloy
Cast Iron
Carbon Steel Alloy Steel Stainless Steel Hardened Steel
a Suitable for shoulder milling
and die machining.

a Suitable for re-grinding.
a Carbide shank.
R0.5
(Max. Depth of Cut)
DCON
DC
0
-0.05
SQUARE
APMX
LU
BALL
LF
GBE06S0640
GBE08S0845
GBE10S1050
GBE12S1255
Stock
MB730
1
1
1
1
DC
LF
6
8
40
45
10
12
50
55
DCON
LU
APMX
6
8
8
13
3.5
6
10
12
13
13
6
6
Hardness
Grade
Cutting Speed
(m/min)
Feed
(mm/rev)
Depth of Cut
(mm)
Hardened Steel
4568HRC
MB730
140 (80200)
0.08 (0.020.15)
< 0.5
Hardened Steel
4568HRC
MB730
100 (60150)
0.06 (0.020.10)
< 0.5
Work Material
J192
Dimensions (mm)
RECOMMENDED CUTTING CONDITIONS FOR GBE TYPE
SOLID END MILLS
TAPER
RADIUS
Order Number
Number
of Flutes
CSRA
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
UWC
Titanium Alloy,
Copper Alloy
37.5
CARBIDE
Aluminium Alloy
DCON(h6)
DC
Type1
APMX
LU
LF
DCON(h6)
LF

0
- 0.009
0
- 0.011
BALL
DC
Type2
APMX
h6
SQUARE
DN
0
- 0.013
APMX
LU
DN
LF
DCON
Stock
CSRAD1000
CSRAD1200
CSRAD1600
CSRAD1800
CSRAD2000
CSRAD2200
CSRAD2500
10
12
16
18
20
22
25
12
15
18
22
25
25
30
25
30
35
50
60
9.4
11.4
15.4
18.0
23.0
75
75
100
100
125
125
125
10
12
16
16
20
20
25
3
3
3
3
3
3
3
a
a
a
a
a
a
a
Type
1
1
1
2
1
2
1
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 3 flute uncoated end mill for roughing aluminium alloy.
J193
CSRA
CARBIDE

y Side milling
Work
material
y Slotting
Aluminium alloy
Aluminium cast
Work
material
Aluminium alloy
Aluminium cast
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
10
12
16
18
20
22
25
19000
16000
12000
10500
9500
8500
7500
8600
8200
7600
7200
7100
6900
6800
9500
8000
6000
5300
4800
4300
3800
3400
3200
3100
2900
2900
2800
2700
10
12
16
18
20
22
25
19000
16000
12000
10500
9500
8500
7500
6800
6500
6100
5800
5700
5500
5400
9500
8000
6000
5300
4800
4300
3800
2700
2600
2400
2400
2300
2200
2200
DC
< 0.5DC
Depth of
cut
Depth of
cut
< 1DC
< 1DC
DC:Dia.
1)
2)
3)
4)
5)
DC:Dia.

These end mills do not have a centre cutting edge, therefore when entering a workpiece use a ramping process rather than vertical feed.
SOLID END MILLS
Using a high-speed and high-rigidity machining center

y Side milling
Work
material
y Slotting
Aluminium alloy
Aluminium cast
Work
material
Aluminium cast
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
10
12
16
18
20
22
25
30000
30000
24000
21000
19000
17000
15000
11000
12000
12000
12000
11000
11000
11000
19000
16000
12000
10500
9500
8500
7500
5400
5300
4900
4700
4600
4300
4300
10
12
16
18
20
22
25
30000
30000
24000
21000
19000
17000
15000
8600
9900
9700
9500
9100
8700
8600
19000
16000
12000
10500
9500
8500
7500
4300
4300
4000
3800
3700
3400
3400
DC
< 0.5DC
Depth of
cut
Depth of
cut
< 1DC
DC:Dia.
1)
2)
3)
4)
5)
J194
Aluminium alloy
< 0.75DC
DC:Dia.

CMRA
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
UWC
Copper Alloy
37.5
CARBIDE
Aluminium Alloy
DCON(h6)
Type1
APMX
LF
LF
BALL
DCON(h6)
DC
Type2
APMX
h6
SQUARE
DC
15

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
APMX
LF
DCON
Stock
CMRAD0300
CMRAD0400
CMRAD0500
CMRAD0600
CMRAD0800
CMRAD1000
CMRAD1200
CMRAD1600
CMRAD2000
CMRAD2500
3
4
5
6
8
10
12
16
20
25
8
11
13
13
19
22
26
32
38
45
50
50
50
50
60
75
75
100
125
125
6
6
6
6
8
10
12
16
20
25
3
3
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
2
2
2
2
2
2
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
J195
CMRA
CARBIDE

y Side milling
Work
material
y Slotting
Aluminium alloy
Aluminium cast
Work
material
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
25
40000
36000
30000
27000
20000
16000
13000
10000
8000
6400
2700
2700
5400
6100
6000
5800
5300
5100
4800
4600
25000
20000
16000
13000
10000
8000
6500
5000
4000
3200
1100
1100
2200
2300
2400
2300
2100
2000
1900
1800
3
4
5
6
8
10
12
16
20
25
30000
24000
19000
16000
12000
9500
8000
6000
4800
3800
1800
2200
2300
2400
2500
2600
2300
2100
2000
2000
16000
12000
10000
8000
6000
5000
4000
3000
2400
1900
700
900
900
1000
1000
1100
900
800
800
700
DC
< 0.25DC
DCepth
of
cut
< 1.5DC
DC:Dia.
1)
2)
3)
4)
5)
SOLID END MILLS
Aluminium cast
Dia.
DC (mm)
Depth of
cut
J196
Aluminium alloy
< 1DC
DC:Dia.


DC<8
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
h6
APMX

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DC > 8
SQUARE
Hardened Steel
(>55HRC)
BALL
CARBIDE
DCON(h6)
Hardened Steel
( < 55HRC)
30
DCON(h6)
(<30HRC)
( < 45HRC)
VF
UWC
DCON(h6)
VFSFPR
Roughing end mill, Short cut length, 3 4 flute
LF
DC
APMX
LF
DCON
Stock
VFSFPRD0300
VFSFPRD0400
VFSFPRD0500
VFSFPRD0600
VFSFPRD0700
VFSFPRD0800
VFSFPRD0900
VFSFPRD1000S08
VFSFPRD1000
VFSFPRD1200S10
VFSFPRD1200
VFSFPRD1400
VFSFPRD1600
VFSFPRD1800
VFSFPRD2000
3
4
5
6
7
8
9
10
10
12
12
14
16
18
20
6
8
10
12
17
17
22
22
22
27
27
27
33
33
38
50
50
50
50
60
60
70
90
70
100
75
75
90
90
100
6
6
6
6
8
8
10
8
10
10
12
12
16
16
20
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
2
1
2
1
3
2
3
2
3
2
3
2
TAPER
Order Number
No. of
Flutes
Unit : mm
SOLID END MILLS
carbon and alloy steel through to hardened steel and difficult-to-cut materials.
RADIUS
a Impact Miracle roughing end mills for a wide range of work materials from
J197

CARBIDE
VFSFPR
y Side milling
Work
material


Pre-hardened steel

Titanium alloy

AISI P20

AISI P21
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
16000
12000
9500
8000
6000
4800
4000
3000
2400
960
960
960
960
1050
1050
960
840
760
13000
9500
7600
6400
4800
3800
3200
2400
1900
640
640
640
680
760
760
700
620
560
6400
4800
3800
3200
2400
1900
1600
1200
1000
260
260
260
290
340
340
320
300
300
5300
4000
3200
2700
2000
1600
1300
1000
800
320
320
320
340
400
400
400
360
320
4200
3200
2500
2100
1600
1300
1100
800
600
70
70
70
75
95
105
110
110
100
Depth of
cut
< 0.5DC
< 0.3DC
< 1.5DC
< 1DC
DC:Dia.
y Slotting
SOLID END MILLS
Work
material


Pre-hardened steel

Titanium alloy

AISI P20

AISI P21
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
13000
9500
7600
6400
4800
3800
3200
2400
1900
720
720
720
720
800
800
750
620
540
11000
8000
6400
5300
4000
3200
2700
2000
1600
480
480
480
480
520
520
520
450
400
4800
3600
3200
2700
2000
1600
1300
1000
800
190
190
190
200
220
220
210
180
160
3200
2400
1900
1600
1200
1000
800
600
500
190
190
190
200
220
220
210
180
160
2100
1600
1300
1100
800
600
500
400
300
25
25
25
30
35
35
40
45
40
DC
Depth of
cut
DC
< 1DC
< 0.5DC
DC:Dia.
J198
VFMFPR
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
VF
UWC
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
30
Copper Alloy
CARBIDE
Aluminium Alloy
LF
DC
APMX
DCON(h6)
Type1
LF
BALL
DCON(h6)
Type2
APMX
h6
SQUARE
DC
15

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
APMX
LF
DCON
Stock
VFMFPRD0500
VFMFPRD0600
VFMFPRD0700
VFMFPRD0800
VFMFPRD0900
VFMFPRD1000
VFMFPRD1200
VFMFPRD1600
VFMFPRD2000
5
6
7
8
9
10
12
16
20
15
17
22
28
28
34
40
48
57
60
60
75
75
100
100
110
125
140
6
6
8
8
10
10
12
16
20
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
Type
1
2
1
2
1
2
2
2
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a Impact Miracle roughing end mills suitable for the machining of deep walled components.
J199

CARBIDE
VFMFPR
y Side milling
Work
material


Pre-hardened steel

Titanium alloy

AISI P20

AISI P21
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
3800
3200
2400
1900
1600
1200
1000
360
360
450
450
400
360
340
3200
2700
2000
1600
1300
1000
800
290
290
360
360
320
290
270
2500
2100
1600
1300
1100
800
600
150
160
160
180
180
160
150
2500
2100
1600
1300
1100
800
600
150
160
160
180
180
160
150
1900
1600
1200
1000
800
600
500
50
60
70
75
80
80
80
< 0.25DC
Depth of
cut
< 2.5DC
DC:Dia.
SOLID END MILLS
J200
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
Type1
DC
CoolStar
30
END MILLS
DCON(h6)
(<30HRC)
( < 45HRC)
VF
UWC
APMX
BALL
LF
SQUARE
VFSFPRCH
Roughing end mill, Short cut length, 4 flute, with multiple internal through coolant holes
DCON=16 DCON=20
h6
0
- 0.011
0
- 0.013
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
VFSFPRCHD1600
VFSFPRCHD2000
16
20
33
38
90
100
16
20
4
4
1
1
TAPER
Type

y Side milling
y Slotting

Titanium alloy
Inconel718
Work
material

Titanium alloy
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
16
20
1200
1000
300
300
800
600
110
100
16
20
800
600
100
80
Depth of
cut
< 0.5DC
< 0.3DC
0.5DC 1.5DC
0.5DC 1.0DC
SOLID END MILLS
Work
material
RADIUS
a Roughing end mill with multiple internal through coolant holes suitable for difficult-to-cut materials.
DC
DC:Dia.
Depth of
cut
0.5DC 1.0DC
DC:Dia.
J201
MIRACLE END MILLS
Hardened Steel
( < 55HRC)
20
DC<8
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DC > 8
Aluminium Alloy
DC
SQUARE
15
h6
APMX

0
- 0.008
0
- 0.009
0
- 0.011
Type2
Type3
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DCON(h6)
(<30HRC)
( < 45HRC)
VC
UWC
DCON(h6)
VCSFPR
DCON(h6)
CARBIDE
LF
0
- 0.013
a 3 4 flute roughing end mill for carbon and alloy steel through to difficult-to-cut and hardened materials.
J202
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VCSFPRD0300
VCSFPRD0400
VCSFPRD0500
VCSFPRD0600
VCSFPRD0700
VCSFPRD0800
VCSFPRD0900
VCSFPRD1000S08
VCSFPRD1000
VCSFPRD1200S10
VCSFPRD1200
VCSFPRD1400
VCSFPRD1600
VCSFPRD1800
VCSFPRD2000
3
4
5
6
7
8
9
10
10
12
12
14
16
18
20
6
8
10
12
17
17
22
22
22
27
27
27
33
33
38
50
50
50
50
60
60
70
90
70
100
75
75
90
90
100
6
6
6
6
8
8
10
8
10
10
12
12
16
16
20
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
2
1
2
1
3
2
3
2
3
2
3
2
CARBIDE

y Side milling
Work
material


Pre-hardened steel

Titanium alloy

AISI P20

AISI P21
AISI 304, AISI 306,

Ti-6Al-4V
AISI H13
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
16000
12000
9500
8000
6000
4800
4000
3000
2400
960
960
960
960
1050
1050
960
840
760
13000
9500
7600
6400
4800
3800
3200
2400
1900
640
640
640
680
760
760
700
620
560
6400
4800
3800
3200
2400
1900
1600
1200
1000
260
260
260
290
340
340
320
300
300
5300
4000
3200
2700
2000
1600
1300
1000
800
100
100
100
110
140
150
150
150
140
4200
3200
2500
2100
1600
1300
1100
800
600
70
70
70
75
95
105
110
110
100
Depth of
cut
< 0.5DC
< 0.3DC
< 1.5DC
< 1DC
DC:Dia.
y Slotting

Pre-hardened steel

Titanium alloy

AISI P20

AISI P21
AISI 304, AISI 306,

Ti-6Al-4V
AISI H13
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
13000
9500
7600
6400
4800
3800
3200
2400
1900
720
720
720
720
800
800
750
620
540
11000
8000
6400
5300
4000
3200
2700
2000
1600
480
480
480
480
520
520
520
450
400
4800
3600
3200
2700
2000
1600
1300
1000
800
190
190
190
200
220
220
210
180
160
3200
2400
1900
1600
1200
1000
800
600
500
50
50
50
55
70
70
75
75
70
2100
1600
1300
1100
800
600
500
400
300
25
25
25
30
35
35
40
45
40
DC
Depth of
cut
SOLID END MILLS
Work
material
DC
< 1DC
< 0.5DC
DC:Dia.
J203
VF6SVRCH
Roughing end mill, Short cut length, 6 flute, Irregular helix flutes, with multiple internal through coolant holes
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
28.5
30
Copper Alloy
Aluminium Alloy
END MILLS
Type1
APMX
DCON(h6)
SQUARE
CoolStar
VF
UWC
DC
CARBIDE
BALL
LF
DCON=16 DCON=20
h6
0
- 0.011
0
- 0.013
a Roughing end mill with multiple internal through coolant holes suitable for difficult-to-cut materials.
TAPER
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
RADIUS
Unit : mm
VF6SVRCHD1600
VF6SVRCHD2000
16
20
33
38
90
100
16
20
6
6
a
a
Type
1
1
SOLID END MILLS
y Side milling
Work
material

Titanium alloy
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
16
20
2400
2000
1200
1000
800
640
160
140
Depth of
cut
< 0.3DC
< 0.2DC
0.5DC 1.5DC
0.5DC 1.5DC
DC:Dia.
J204
MS PLUS END MILLS
MP2SSB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
30
UWC
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
Type1
DCON(h5)
APMX
DC
LF
Type2
DCON(h5)
PRFRAD
APMX
LF
R
h5
0.1<PRFRAD<6
BALL
PRFRAD
SQUARE
DC
15
0.005

0
- 0.005
0
- 0.006
0
- 0.008
APMX
LF
DCON
0.1
0.2
0.3
0.4
0.5
0.5
0.75
0.75
1
1.5
2
2.5
3
4
5
6
0.2
0.4
0.6
0.8
1
1
1.5
1.5
2
3
4
5
6
8
10
12
0.2
0.4
0.6
0.8
1
1
1.5
1.5
2
3
4
5
6
8
10
12
40
40
40
40
40
40
40
40
45
45
45
50
50
60
70
75
4
4
4
4
4
6
4
6
6
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
TAPER
DC
Stock
MP2SSBR0010
MP2SSBR0020
MP2SSBR0030
MP2SSBR0040
MP2SSBR0050
MP2SSBR0050S06
MP2SSBR0075
MP2SSBR0075S06
MP2SSBR0100
MP2SSBR0150
MP2SSBR0200
MP2SSBR0250
MP2SSBR0300
MP2SSBR0400
MP2SSBR0500
MP2SSBR0600
PRFRAD
No. of
Flutes
Order Number
Unit : mm
SOLID END MILLS
for a wide range of workpiece materials such as carbon steel, alloy steel and hardened steel.
RADIUS
a 2-flute ball nose end mills with short cutting edge length for general purpose. Excellent performance
J205
MS PLUS END MILLS

CARBIDE
MP2SB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
30
UWC
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
SQUARE
15
Type1
DCON(h5)
PRFRAD
APMX
DC
LF
Type2
DCON(h5)
BALL
PRFRAD
APMX
LF
R
h5
0.1<PRFRAD<6
0.005

0
- 0.005
0
- 0.006
0
- 0.008
SOLID END MILLS
J206
PRFRAD
DC
APMX
LF
DCON
Stock
MP2SBR0010
MP2SBR0015
MP2SBR0020
MP2SBR0020S06
MP2SBR0025
MP2SBR0030
MP2SBR0030S06
MP2SBR0035
MP2SBR0040
MP2SBR0040S06
MP2SBR0045
MP2SBR0050
MP2SBR0050S06
MP2SBR0060
MP2SBR0070
MP2SBR0075
MP2SBR0075S06
MP2SBR0080
MP2SBR0090
MP2SBR0100
MP2SBR0100S06
MP2SBR0125
MP2SBR0150
MP2SBR0200
MP2SBR0250
MP2SBR0300
MP2SBR0400
MP2SBR0500
MP2SBR0600
Unit : mm
No. of
Flutes
Order Number
TAPER
RADIUS
a 2-flute ball nose end mills with short cutting edge length for general purpose. Excellent performance
0.1
0.15
0.2
0.2
0.25
0.3
0.3
0.35
0.4
0.4
0.45
0.5
0.5
0.6
0.7
0.75
0.75
0.8
0.9
1
1
1.25
1.5
2
2.5
3
4
5
6
0.2
0.3
0.4
0.4
0.5
0.6
0.6
0.7
0.8
0.8
0.9
1
1
1.2
1.4
1.5
1.5
1.6
1.8
2
2
2.5
3
4
5
6
8
10
12
0.3
0.5
0.6
0.6
0.8
0.9
0.9
1.1
1.2
1.2
1.4
1.5
1.5
1.8
2.1
2.3
2.3
2.4
2.7
3
3
3.8
4.5
6
7.5
9
12
15
18
45
45
45
50
45
45
50
45
45
50
45
45
50
45
45
45
50
45
45
50
50
50
70
70
80
80
90
100
110
4
4
4
6
4
4
6
4
4
6
4
4
6
4
4
4
6
4
4
4
6
4
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
15
PRFRAD
DCON(h5)
DC
Type1
APMX
LF
PRFRAD
DCON(h5)
DC
Type1
APMX
LF
R
h5
0.25<PRFRAD<6
BALL
(<30HRC)
( < 45HRC)
30
UWC
SQUARE
MP2MB
0.005

0
- 0.005
0
- 0.006
0
- 0.008
PRFRAD
DC
APMX
LF
DCON
Stock
MP2MBR0025
MP2MBR0030
MP2MBR0040
MP2MBR0050
MP2MBR0060
MP2MBR0070
MP2MBR0075
MP2MBR0080
MP2MBR0090
MP2MBR0100
MP2MBR0125
MP2MBR0150S03
MP2MBR0150
MP2MBR0175
MP2MBR0200S04
MP2MBR0200
MP2MBR0250
MP2MBR0300
MP2MBR0400
MP2MBR0500
MP2MBR0600
0.25
0.3
0.4
0.5
0.6
0.7
0.75
0.8
0.9
1
1.25
1.5
1.5
1.75
2
2
2.5
3
4
5
6
0.5
0.6
0.8
1
1.2
1.4
1.5
1.6
1.8
2
2.5
3
3
3.5
4
4
5
6
8
10
12
1
1.2
1.6
2.5
2.5
3
4
4
5
6
6
8
8
8
8
8
12
12
14
18
22
45
45
45
45
45
45
45
45
45
50
50
70
70
70
70
70
80
80
90
100
110
4
4
4
4
4
4
4
4
4
4
4
3
6
6
4
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
2
2
2
2
TAPER
Order Number
No. of
Flutes
Unit : mm
SOLID END MILLS
RADIUS
a 2-flute ball nose end mills with medium cutting edge length for general purpose. Excellent performance
J207
MS PLUS END MILLS

CARBIDE
Ball nose, Short cut length, 2 flute, Short shank MP2SSB

Ball nose, Short cut length, 2 flute MP2SB Ball nose, Medium cutting length, 2 flute MP2MB

Work
material
Mild Steel,Carbon steel,Alloy steel,Pre-hardened steel, Hardened steel (45 55HRC)

Hardened steel ( 45HRC)
AISI 1050, AISI P21, AISI H13
AISI 420, AISI H13
%>15
%>15
%>15
%<15
%<15
%<15
Depth of cut Pick feed
R
pf
ap
pf
pf
PRFRAD Revolution Feed rate Revolution Feed rate ap
Revolution Feed rate Revolution Feed rate
Revolution Feed rate Revolution Feed rate ap
(mm)
(min-1) (mm/min) (min-1) (mm/min) (mm) (mm) (min-1) (mm/min) (min-1) (mm/min) (mm) (mm) (min-1) (mm/min) (min-1) (mm/min) (mm) (mm)
R0.1
R0.15
R0.2
R0.25
R0.3
R0.4
R0.5
R0.75
R1
R1.25
R1.5
R2
R2.5
R3
R4
R5
R6
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
32000
25000
21000
16000
13000
9000
300
500
1600
2400
3200
4800
5600
6500
6500
7000
7500
7500
6000
5800
4500
3600
2500
40000
40000
40000
40000
40000
40000
40000
40000
39000
33000
27000
20000
16000
13000
10000
8000
6000
250
350
1200
1400
1600
2400
3200
4000
4700
4500
4300
3600
2900
2600
2000
1700
1300
0.003
0.007
0.02
0.025
0.03
0.05
0.06
0.09
0.11
0.12
0.13
0.15
0.2
0.25
0.3
0.5
0.5
0.02
0.03
0.04
0.05
0.06
0.08
0.1
0.15
0.2
0.25
0.3
0.4
0.5
0.6
0.8
1.0
1.2
40000
40000
40000
40000
40000
40000
40000
40000
40000
36000
32000
25000
20000
17000
13000
10000
7200
300
500
1300
1900
2500
4000
5600
6500
6500
6500
6000
6000
5400
4700
3600
2900
2000
40000
40000
40000
40000
40000
40000
40000
32000
31000
26000
22000
16000
13000
10000
8000
6400
4800
250
350
950
1100
1300
1900
3000
3200
3500
3500
3400
2700
2300
2000
1500
1200
1000
0.003
0.007
0.015
0.02
0.025
0.04
0.05
0.08
0.11
0.12
0.13
0.15
0.2
0.25
0.3
0.5
0.5
0.02
0.03
0.04
0.05
0.06
0.08
0.1
0.15
0.2
0.25
0.3
0.4
0.5
0.6
0.8
1.0
1.2
40000
40000
40000
40000
40000
40000
40000
40000
40000
36000
32000
25000
20000
17000
13000
10000
8500
300 40000 250

500 40000 350
1300 40000 950
1900 40000 1100
2500 40000 1300
4000 40000 1900
5600 40000 3000
6500 32000 3200
6500 31000 3500
6500 26000 3500
6000 22000 3400
6000 16000 2700
5400 13000 2300
4700 10000 2000
3600 8000 1500
2900 6400 1200
2300 5300 1100
0.003
0.007
0.015
0.02
0.025
0.04
0.05
0.08
0.11
0.12
0.13
0.15
0.2
0.25
0.3
0.5
0.5
0.02
0.03
0.04
0.05
0.06
0.08
0.1
0.15
0.2
0.25
0.3
0.6
0.75
0.9
1.6
2.0
2.4
<pf
SOLID END MILLS
Depth of
cut
<ap
1) % is the inclination angle of the machined surface.

4) Standard cutting conditions of austenitic stainless steel and titanium alloy, please reduce to 60% revolution and 45% feedrate.
(Hardened steel (45 55HRC) table above)
End mill
pf
J208
ap
PRFRAD
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
DC
DN
Hardened Steel
( < 55HRC)
30
UWC
h5
0.05<PRFRAD<3
DCON(h5)
LF
DC
PRFRAD
Type1
APMX
LU
LF
0.005
BALL
Inclined angle
12
DCON(h5)
Effective
length
Effective length
for inclined angle
Type1
APMX
LU
DN
PRFRAD
SQUARE
MP2XLB
4<DCON<6
0
- 0.005
APMX
LU
DN
LF
DCON
MP2XLBR0005N003
MP2XLBR0005N005
MP2XLBR0010N005
MP2XLBR0010N008
MP2XLBR0010N010
MP2XLBR0010N013
MP2XLBR0010N015
MP2XLBR0010N018
MP2XLBR0010N020
MP2XLBR0010N025
MP2XLBR0015N005
MP2XLBR0015N008
MP2XLBR0015N010
MP2XLBR0015N010S06
MP2XLBR0015N013
MP2XLBR0015N013S06
MP2XLBR0015N015
MP2XLBR0015N015S06
MP2XLBR0015N018
MP2XLBR0015N020
MP2XLBR0015N025
MP2XLBR0015N030
MP2XLBR0015N035
MP2XLBR0015N040
MP2XLBR0020N005
MP2XLBR0020N008
MP2XLBR0020N010
MP2XLBR0020N010S06
MP2XLBR0020N015
MP2XLBR0020N020
MP2XLBR0020N020S06
MP2XLBR0020N025
MP2XLBR0020N030
MP2XLBR0020N035
0.05
0.05
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.1
0.1
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.08
0.08
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.5
0.5
0.75
1
1.25
1.5
1.75
2
2.5
0.5
0.75
1
1
1.25
1.25
1.5
1.5
1.75
2
2.5
3
3.5
4
0.5
0.75
1
1
1.5
2
2
2.5
3
3.5
0.085
0.085
0.18
0.18
0.18
0.18
0.18
0.18
0.18
0.18
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.28
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
4
4
4
4
4
4
4
4
4
4
4
4
6
4
6
4
6
4
4
4
4
4
4
4
4
4
6
4
4
6
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
0.3
0.5
0.5
0.8
1.0
1.3
1.6
1.8
2.1
2.6
0.5
0.8
1.0
1.0
1.3
1.3
1.6
1.6
1.8
2.1
2.6
3.1
3.7
4.2
0.5
0.7
1.0
1.0
1.5
2.1
2.1
2.6
3.1
3.6
0.3
0.5
0.5
0.8
1.1
1.4
1.6
1.9
2.2
2.7
0.5
0.8
1.1
1.1
1.4
1.4
1.6
1.6
1.9
2.2
2.7
3.3
3.8
4.4
0.5
0.8
1.1
1.1
1.6
2.2
2.2
2.7
3.2
3.8
0.4
0.6
0.6
0.9
1.2
1.5
1.8
2.1
2.4
3.0
0.6
0.9
1.2
1.2
1.5
1.5
1.8
1.8
2.1
2.4
3.0
3.6
4.2
4.8
0.5
0.9
1.2
1.2
1.7
2.3
2.3
2.9
3.5
4.1
0.4
0.7
0.7
1.0
1.3
1.7
2.0
2.3
2.6
3.3
0.6
1.0
1.3
1.3
1.6
1.6
2.0
2.0
2.3
2.6
3.3
4.0
4.6
5.3
0.6
0.9
1.3
1.3
1.9
2.6
2.6
3.3
3.9
4.6
TAPER
DC
Type
PRFRAD
Stock
Order Number
No. of Flutes
Unit : mm
SOLID END MILLS
such as carbon steel, alloy steel and hardened steel.
RADIUS
a 2-flute long neck ball nose end mills. Excellent performance for a wide range of workpiece materials
J209
MS PLUS END MILLS
MP2XLB
DC
APMX
LU
DN
LF
DCON
MP2XLBR0020N040
MP2XLBR0020N045
MP2XLBR0020N050
MP2XLBR0020N055
MP2XLBR0020N060
MP2XLBR0025N010
MP2XLBR0025N015
MP2XLBR0025N015S06
MP2XLBR0025N020
MP2XLBR0025N020S06
MP2XLBR0025N025
MP2XLBR0025N025S06
MP2XLBR0025N030
MP2XLBR0025N030S06
MP2XLBR0025N035
MP2XLBR0025N040
MP2XLBR0025N045
MP2XLBR0025N050
MP2XLBR0025N055
MP2XLBR0025N060
MP2XLBR0025N070
MP2XLBR0025N080
MP2XLBR0025N090
MP2XLBR0025N100
MP2XLBR0030N015
MP2XLBR0030N015S06
MP2XLBR0030N020
MP2XLBR0030N020S06
MP2XLBR0030N025
MP2XLBR0030N030
MP2XLBR0030N030S06
MP2XLBR0030N035
MP2XLBR0030N040
MP2XLBR0030N040S06
MP2XLBR0030N045
MP2XLBR0030N050
MP2XLBR0030N050S06
MP2XLBR0030N055
MP2XLBR0030N060
MP2XLBR0030N060S06
MP2XLBR0030N065
MP2XLBR0030N070
MP2XLBR0030N080
MP2XLBR0030N080S06
MP2XLBR0030N085
MP2XLBR0030N090
MP2XLBR0030N095
MP2XLBR0030N100
MP2XLBR0030N110
MP2XLBR0030N120
MP2XLBR0040N020
MP2XLBR0040N020S06
0.2
0.2
0.2
0.2
0.2
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.3
0.3
0.3
0.3
0.3
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.37
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.6
0.6
4
4.5
5
5.5
6
1
1.5
1.5
2
2
2.5
2.5
3
3
3.5
4
4.5
5
5.5
6
7
8
9
10
1.5
1.5
2
2
2.5
3
3
3.5
4
4
4.5
5
5
5.5
6
6
6.5
7
8
8
8.5
9
9.5
10
11
12
2
2
0.37
0.37
0.37
0.37
0.37
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.57
0.77
0.77
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
4
4
4
4
4
4
6
4
6
4
6
4
6
4
4
4
4
4
4
4
4
4
4
4
6
4
6
4
4
6
4
4
6
4
4
6
4
4
6
4
4
4
6
4
4
4
4
4
4
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Type
PRFRAD
Stock
Order Number
J210
Unit : mm
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
4.2
4.7
5.2
5.7
6.2
1.0
1.5
1.5
2.1
2.1
2.6
2.6
3.1
3.1
3.6
4.1
4.7
5.2
5.7
6.2
7.3
8.3
9.4
10.4
1.5
1.5
2.1
2.1
2.6
3.1
3.1
3.7
4.2
4.2
4.7
5.2
5.2
5.8
6.3
6.3
6.8
7.3
8.4
8.4
8.9
9.4
9.9
10.5
11.5
12.5
2.1
2.1
4.3
4.9
5.4
6.0
6.5
1.0
1.6
1.6
2.1
2.1
2.7
2.7
3.2
3.2
3.8
4.3
4.9
5.4
6.0
6.5
7.6
8.7
9.8
10.9
1.6
1.6
2.2
2.2
2.7
3.3
3.3
3.8
4.4
4.4
4.9
5.5
5.5
6.0
6.6
6.6
7.1
7.6
8.7
8.7
9.3
9.8
10.4
10.9
12.0
13.1
2.2
2.2
4.7
5.3
5.9
6.5
7.1
1.1
1.7
1.7
2.3
2.3
2.9
2.9
3.5
3.5
4.1
4.7
5.3
5.9
6.5
7.1
8.3
9.5
10.7
11.9
1.8
1.8
2.4
2.4
3.0
3.6
3.6
4.2
4.8
4.8
5.4
6.0
6.0
6.6
7.2
7.2
7.8
8.4
9.6
9.6
10.2
10.8
11.4
12.0
13.2
14.4
2.4
2.4
5.2
5.9
6.6
7.2
7.9
1.2
1.9
1.9
2.6
2.6
3.2
3.2
3.9
3.9
4.6
5.2
5.9
6.6
7.2
7.9
9.2
10.5
11.9
13.2
2.0
2.0
2.6
2.6
3.3
4.0
4.0
4.6
5.3
5.3
5.9
6.6
6.6
7.3
7.9
7.9
8.6
9.3
10.6
10.6
11.3
11.9
12.6
13.2
14.6
15.9
2.6
2.6
CARBIDE
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1.05
1.05
1.05
1.1
DCON
2.4
3
3
4
4
5
6
7
8
9
10
12
3
3
4
4
5
5
6
6
7
8
8
9
10
10
12
12
14
16
16
18
20
20
6
6
8
8
10
10
12
12
14
16
16
18
20
24
8
12
16
3
0.77
0.77
0.77
0.77
0.77
0.77
0.77
0.77
0.77
0.77
0.77
0.77
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.34
1.34
1.34
1.44
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
60
50
60
55
55
65
55
55
65
50
55
50
55
50
55
50
65
55
55
65
60
60
60
50
50
50
50
6
4
6
4
6
4
4
4
4
4
4
4
4
6
4
6
4
6
4
6
4
4
6
4
4
6
4
6
4
4
6
4
4
6
4
6
4
6
4
6
4
6
4
4
6
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
2.5
3.1
3.1
4.2
4.2
5.2
6.3
7.3
8.4
9.4
10.5
12.5
3.2
3.2
4.3
4.3
5.3
5.3
6.4
6.4
7.4
8.5
8.5
9.5
10.6
10.6
12.7
12.7
14.8
16.9
16.9
18.9
21.0
21.0
6.4
6.4
8.5
8.5
10.6
10.6
12.7
12.7
14.8
16.9
16.9
18.9
21.0
25.2
8.4
12.6
16.8
3.1
2.6
3.3
3.3
4.4
4.4
5.5
6.5
7.6
8.7
9.8
10.9
13.1
3.4
3.4
4.5
4.5
5.6
5.6
6.7
6.7
7.8
8.9
8.9
10.0
11.1
11.1
13.2
13.2
15.4
17.6
17.6
19.8
22.0
22.0
6.7
6.7
8.9
8.9
11.0
11.0
13.2
13.2
15.4
17.6
17.6
19.8
21.9
26.3
8.8
13.1
17.5
3.3
2.8
3.6
3.6
4.8
4.8
6.0
7.2
8.4
9.5
10.7
11.9
14.3
3.7
3.7
4.9
4.9
6.1
6.1
7.3
7.3
8.5
9.7
9.7
10.9
12.1
12.1
14.5
14.5
16.9
19.3
19.3
21.7
24.1
24.1
7.3
7.3
9.7
9.7
12.1
12.1
14.5
14.5
16.9
19.3
19.3
21.7
24.0
28.8
9.6
14.4
19.2
3.6
3.1
3.9
3.9
5.2
5.2
6.6
7.9
9.2
10.6
11.9
13.2
15.9
4.1
4.1
5.4
5.4
6.7
6.7
8.1
8.1
9.4
10.7
10.7
12.0
13.4
13.4
16.0
16.0
18.7
21.3
21.3
24.0
26.6
26.6
8.0
8.0
10.7
10.7
13.3
13.3
16.0
16.0
18.7
21.3
21.3
24.0
26.6
SQUARE
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.4
1.4
1.4
1.5
LF
BALL
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.75
DN
RADIUS
MP2XLBR0040N024S06
MP2XLBR0040N030
MP2XLBR0040N030S06
MP2XLBR0040N040
MP2XLBR0040N040S06
MP2XLBR0040N050
MP2XLBR0040N060
MP2XLBR0040N070
MP2XLBR0040N080
MP2XLBR0040N090
MP2XLBR0040N100
MP2XLBR0040N120
MP2XLBR0050N030
MP2XLBR0050N030S06
MP2XLBR0050N040
MP2XLBR0050N040S06
MP2XLBR0050N050
MP2XLBR0050N050S06
MP2XLBR0050N060
MP2XLBR0050N060S06
MP2XLBR0050N070
MP2XLBR0050N080
MP2XLBR0050N080S06
MP2XLBR0050N090
MP2XLBR0050N100
MP2XLBR0050N100S06
MP2XLBR0050N120
MP2XLBR0050N120S06
MP2XLBR0050N140
MP2XLBR0050N160
MP2XLBR0050N160S06
MP2XLBR0050N180
MP2XLBR0050N200
MP2XLBR0050N200S06
MP2XLBR0060N060
MP2XLBR0060N060S06
MP2XLBR0060N080
MP2XLBR0060N080S06
MP2XLBR0060N100
MP2XLBR0060N100S06
MP2XLBR0060N120
MP2XLBR0060N120S06
MP2XLBR0060N140
MP2XLBR0060N160
MP2XLBR0060N160S06
MP2XLBR0060N180
MP2XLBR0060N200
MP2XLBR0060N240
MP2XLBR0070N080
MP2XLBR0070N120
MP2XLBR0070N160
MP2XLBR0075N030
LU
TAPER
APMX
SOLID END MILLS
DC
Type
PRFRAD
Stock
Order Number
No. of Flutes
Unit : mm
10.6
15.9
21.2
3.9
* No interference
J211
MS PLUS END MILLS
MP2XLB
DC
APMX
LU
DN
LF
DCON
MP2XLBR0075N040
MP2XLBR0075N060
MP2XLBR0075N060S06
MP2XLBR0075N080
MP2XLBR0075N080S06
MP2XLBR0075N100
MP2XLBR0075N100S06
MP2XLBR0075N120
MP2XLBR0075N120S06
MP2XLBR0075N140
MP2XLBR0075N160
MP2XLBR0075N160S06
MP2XLBR0075N180
MP2XLBR0075N200
MP2XLBR0075N220
MP2XLBR0080N080
MP2XLBR0080N120
MP2XLBR0080N160
MP2XLBR0080N200
MP2XLBR0090N080
MP2XLBR0090N120
MP2XLBR0090N160
MP2XLBR0090N200
MP2XLBR0100N040
MP2XLBR0100N040S06
MP2XLBR0100N060
MP2XLBR0100N060S06
MP2XLBR0100N080
MP2XLBR0100N080S06
MP2XLBR0100N100
MP2XLBR0100N100S06
MP2XLBR0100N120
MP2XLBR0100N120S06
MP2XLBR0100N140
MP2XLBR0100N140S06
MP2XLBR0100N160
MP2XLBR0100N160S06
MP2XLBR0100N180
MP2XLBR0100N180S06
MP2XLBR0100N200
MP2XLBR0100N200S06
MP2XLBR0100N220
MP2XLBR0100N250
MP2XLBR0100N250S06
MP2XLBR0100N300
MP2XLBR0100N300S06
MP2XLBR0100N350
MP2XLBR0100N350S06
MP2XLBR0100N400
MP2XLBR0100N400S06
MP2XLBR0125N100
MP2XLBR0125N150
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.8
0.8
0.8
0.8
0.9
0.9
0.9
0.9
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.25
1.25
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.2
1.2
1.2
1.2
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.9
1.9
4
6
6
8
8
10
10
12
12
14
16
16
18
20
22
8
12
16
20
8
12
16
20
4
4
6
6
8
8
10
10
12
12
14
14
16
16
18
18
20
20
22
25
25
30
30
35
35
40
40
10
15
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.54
1.54
1.54
1.54
1.74
1.74
1.74
1.74
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
1.94
2.4
2.4
50
50
50
50
60
50
60
50
60
55
55
60
60
60
60
55
55
55
55
55
55
55
55
50
50
50
50
50
50
50
50
50
60
55
60
55
65
55
65
65
65
65
65
90
80
90
80
90
80
90
55
55
4
4
6
4
6
4
6
4
6
4
4
6
4
4
4
4
4
4
4
4
4
4
4
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
4
6
4
6
4
6
4
6
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Type
PRFRAD
Stock
Order Number
J212
Unit : mm
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
4.2
6.3
6.3
8.4
8.4
10.5
10.5
12.6
12.6
14.7
16.8
16.8
18.9
21.0
23.0
8.4
12.6
16.8
21.0
8.4
12.6
16.8
20.9
4.2
4.2
6.3
6.3
8.4
8.4
10.5
10.5
12.6
12.6
14.7
14.7
16.8
16.8
18.9
18.9
20.9
20.9
23.0
26.2
26.2
31.4
31.4
36.6
36.6
41.8
41.8
10.4
15.6
4.4
6.6
6.6
8.8
8.8
11.0
11.0
13.1
13.1
15.3
17.5
17.5
19.7
21.9
24.0
8.8
13.1
17.5
21.9
8.8
13.1
17.5
21.8
4.4
4.4
6.6
6.6
8.8
8.8
10.9
10.9
13.1
13.1
15.3
15.3
17.5
17.5
19.7
19.7
21.8
21.8
24.0
27.3
27.3
32.7
32.7
38.2
38.2
43.6
43.6
10.8
16.3
4.8
7.2
7.2
9.6
9.6
12.0
12.0
14.4
14.4
16.8
19.2
19.2
21.6
23.9
26.3
9.6
14.4
19.1
23.9
9.6
14.3
19.1
23.9
4.7
4.7
7.1
7.1
9.5
9.5
11.9
11.9
14.3
14.3
16.7
16.7
19.1
19.1
21.5
21.5
23.9
23.9
26.3
5.2
7.9
7.9
10.6
10.6
13.2
13.2
15.9
15.9
18.5
21.2
21.2
23.8
*
*
10.5
15.9
21.2
10.5
15.8
21.1
5.2
5.2
7.8
7.8
10.5
10.5
13.1
13.1
15.8
15.8
18.4
18.4
21.1
23.8
26.4
*
*
29.9 33.0
35.9
41.8
*
*
*
*
*
*
47.8
11.8 12.9
17.8
*
* No interference
CARBIDE
DCON
MP2XLBR0125N200
MP2XLBR0125N250
MP2XLBR0125N300
MP2XLBR0125N350
MP2XLBR0150N060S03
MP2XLBR0150N080
MP2XLBR0150N100
MP2XLBR0150N120
MP2XLBR0150N140
MP2XLBR0150N160
MP2XLBR0150N200
MP2XLBR0150N250
MP2XLBR0150N300
MP2XLBR0150N350
MP2XLBR0150N400
MP2XLBR0175N150
MP2XLBR0175N250
MP2XLBR0175N350
MP2XLBR0175N450
MP2XLBR0200N080S04
MP2XLBR0200N100
MP2XLBR0200N120
MP2XLBR0200N140
MP2XLBR0200N160
MP2XLBR0200N200
MP2XLBR0200N250
MP2XLBR0200N300
MP2XLBR0200N350
MP2XLBR0200N400
MP2XLBR0200N450
MP2XLBR0200N500
MP2XLBR0250N150
MP2XLBR0250N200
MP2XLBR0250N250
MP2XLBR0250N300
MP2XLBR0250N350
MP2XLBR0250N400
MP2XLBR0300N200
MP2XLBR0300N250
MP2XLBR0300N300
MP2XLBR0300N400
MP2XLBR0300N500
1.25
1.25
1.25
1.25
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.75
1.75
1.75
1.75
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
3
3.5
3.5
3.5
3.5
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
6
6
6
6
6
1.9
1.9
1.9
1.9
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.6
2.6
2.6
2.6
3
3
3
3
3
3
3
3
3
3
3
3
3.8
3.8
3.8
3.8
3.8
3.8
6
6
6
6
6
20
25
30
35
6
8
10
12
14
16
20
25
30
35
40
15
25
35
45
8
10
12
14
16
20
25
30
35
40
45
50
15
20
25
30
35
40
20
25
30
40
50
2.4
2.4
2.4
2.4
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
3.4
3.4
3.4
3.4
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
4.9
4.9
4.9
4.9
4.9
4.9
5.85
5.85
5.85
5.85
5.85
55
70
70
70
60
60
60
60
60
70
70
70
70
90
90
65
65
90
90
65
65
65
65
70
70
70
80
80
90
90
100
70
70
70
80
80
90
70
70
80
90
100
4
4
4
4
3
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
20.8
26.1
31.3
36.5
21.7
27.2
32.6
38.1
*
*
*
*
*
*
*
*
*
*
8.3
10.4
12.5
14.6
16.7
20.8
26.1
31.3
36.5
41.7
15.6
26.0
36.5
46.9
10.4
12.5
14.6
16.6
20.8
26.0
31.2
36.5
41.7
46.9
52.1
15.6
20.8
26.0
31.2
36.4
41.7
*
*
*
*
*
8.6
10.8
13.0
15.2
17.3
21.7
27.2
32.6
38.0
43.5
16.2
27.1
38.0
48.9
10.8
12.9
15.1
17.3
21.7
27.1
32.6
38.0
43.5
48.9
54.3
16.2
21.6
27.1
9.3
11.7
14.1
16.5
18.9
23.7
29.7
35.7
41.7
10.2
12.9
15.5
18.2
20.8
26.1
*
*
*
*
*
*
*
*
*
*
*
17.7 19.4
29.6
11.6
14.0
16.4
18.8
23.6
29.6
12.7
15.4
18.0
20.7
*
*
* *
* *
* *
* *
* *
* *
* *
* *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
*No interference
* *
SQUARE
LF
BALL
DN
RADIUS
LU
TAPER
APMX
SOLID END MILLS
DC
Type
PRFRAD
Stock
Order Number
No. of Flutes
Unit : mm
J213
MS PLUS END MILLS

CARBIDE
MP2XLB
Work material
Neck length
R
PRFRAD (mm) LU (mm)
R0.05
R0.1
R0.15
SOLID END MILLS
R0.2
R0.25
R0.3
0.3
0.5
0.5
1
1.5
2
2.5
1
1.5
2
2.5
3
3.5
4
1
2
3
4
5
6
2
3
4
5
6
7
8
10
2
3
4
5
6
7
8
9
10
11
12
Carbon steel,Alloy steel,Alloy Tool Steel,

Pre-hardened steel,
Precipitation hardeningstainless steel

Hardened steell ( 52HRC)
AISI 1055, AISI P21, ASTM 630
AISI H13, AISI 420, AISI 431
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
50000
50000
50000
50000
40000
40000
40000
50000
50000
50000
40000
40000
30000
30000
50000
50000
50000
40000
40000
30000
50000
50000
45000
45000
36000
32000
32000
26000
50000
50000
44000
37000
37000
35000
35000
30000
30000
22000
22000
200
200
400
400
300
200
100
600
600
600
400
300
250
200
1800
1300
900
600
400
200
2500
1500
1200
900
600
400
300
200
3500
3500
2500
1200
1000
750
600
500
500
300
200
0.002
0.001
0.003
0.002
0.001
0.001
0.001
0.007
0.005
0.003
0.003
0.002
0.002
0.002
0.015
0.01
0.005
0.004
0.003
0.002
0.02
0.015
0.01
0.007
0.006
0.005
0.003
0.002
0.03
0.03
0.02
0.01
0.008
0.008
0.006
0.004
0.003
0.002
0.002
50000
50000
50000
50000
40000
40000
40000
50000
50000
50000
40000
40000
30000
30000
50000
50000
50000
40000
40000
30000
50000
50000
45000
45000
36000
32000
32000
26000
50000
50000
44000
37000
37000
35000
35000
30000
30000
22000
22000
200
200
320
320
240
160
80
480
480
480
320
240
200
160
1400
1000
700
480
320
160
2000
1200
950
700
480
320
240
160
2800
2800
2000
950
800
600
480
400
400
240
160
0.002
0.002
0.003
0.002
0.001
0.001
0.001
0.007
0.005
0.003
0.003
0.002
0.002
0.002
0.015
0.01
0.005
0.004
0.003
0.002
0.02
0.015
0.01
0.007
0.006
0.005
0.003
0.002
0.03
0.03
0.02
0.01
0.008
0.008
0.006
0.004
0.003
0.002
0.002
50000
50000
50000
50000
40000
40000
40000
50000
50000
50000
40000
40000
30000
30000
50000
50000
50000
40000
40000
30000
50000
50000
45000
45000
36000
32000
32000
26000
50000
50000
44000
37000
37000
35000
35000
30000
30000
22000
22000
200
200
320
320
240
160
80
480
480
480
320
240
200
160
1400
1000
700
480
320
160
2000
1200
950
700
480
320
240
160
2800
2800
2000
950
800
600
480
400
400
240
160
0.004
0.002
0.006
0.004
0.002
0.002
0.002
0.014
0.01
0.006
0.006
0.004
0.004
0.004
0.03
0.02
0.01
0.008
0.006
0.004
0.04
0.03
0.02
0.014
0.012
0.01
0.006
0.004
0.06
0.06
0.04
0.02
0.016
0.016
0.012
0.008
0.006
0.004
0.004
<0.1PRFRAD
Depth ofcut
<0.2PRFRAD
(PRFRAD <1)
(PRFRAD> 1)
ap
PRFRAD:Radius
1) When the inclination angle of machined surface is large, or machining with large cutting load such as corner area, reduce the revolution and feed rate.
2) The use of oil mist is recommended when machining with small diameter.
3) The revolution and feed rate can increase for the small depth of cut (ap).
5) For hardened steel over 55HRC, use VF2XLB.
J214
CARBIDE
Neck length
R
PRFRAD (mm) LU (mm)
R0.4
R0.5
R0.6
R0.7
R0.75
R0.8
R0.9
2
3
4
5
6
7
8
10
12
3
4
6
8
10
12
14
16
18
20
6
8
10
12
18
24
8
12
16
6
8
10
12
16
20
22
8
12
16
20
8
12
16
20

Hardened steell ( 52HRC)
AISI 1055, AISI P21, ASTM 630
AISI H13, AISI 420, AISI 431
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
50000
50000
50000
35000
35000
30000
30000
30000
22000
40000
40000
35000
30000
20000
20000
18000
18000
13000
13000
40000
40000
27000
16000
15000
11000
40000
26000
17000
40000
40000
40000
32000
15000
12000
9000
40000
36000
14000
12000
40000
40000
28000
10000
4400
4000
4000
2400
2400
1500
1500
700
500
4000
4000
3000
2000
1000
1000
600
500
300
250
4400
4000
1900
1400
700
300
4000
2000
1400
6000
6000
5000
3400
1400
900
400
6000
4500
1400
1000
6600
5000
2800
800
0.04
0.04
0.02
0.02
0.02
0.015
0.01
0.008
0.006
0.05
0.05
0.03
0.02
0.01
0.01
0.008
0.008
0.005
0.005
0.04
0.04
0.02
0.02
0.008
0.006
0.05
0.04
0.03
0.07
0.07
0.06
0.04
0.03
0.02
0.01
0.08
0.06
0.04
0.03
0.09
0.07
0.04
0.03
50000
50000
50000
35000
35000
30000
30000
30000
22000
40000
40000
35000
30000
20000
20000
18000
18000
13000
13000
40000
40000
27000
16000
15000
11000
40000
26000
17000
36000
36000
36000
29000
15000
12000
9000
32000
29000
14000
12000
32000
32000
22000
10000
3500
3200
3200
1900
1900
1200
1200
560
400
3200
3200
2400
1600
800
800
480
400
240
200
3500
3200
1500
1100
560
240
3200
1600
1120
4300
4300
3600
2400
1100
720
320
3800
2800
1100
800
4200
3200
1800
640
0.04
0.04
0.02
0.02
0.02
0.015
0.01
0.008
0.006
0.05
0.05
0.03
0.02
0.01
0.01
0.008
0.008
0.005
0.005
0.04
0.04
0.02
0.02
0.008
0.006
0.05
0.04
0.03
0.07
0.07
0.06
0.04
0.03
0.02
0.01
0.08
0.06
0.04
0.03
0.09
0.07
0.04
0.03
50000
50000
50000
35000
35000
30000
30000
30000
22000
40000
40000
35000
30000
20000
20000
18000
18000
13000
13000
40000
40000
27000
16000
15000
11000
40000
26000
17000
36000
36000
36000
29000
15000
12000
9000
32000
29000
14000
12000
32000
32000
22000
10000
3500
3200
3200
1900
1900
1200
1200
560
400
3200
3200
2400
1600
800
800
480
400
240
200
3500
3200
1500
1100
560
240
2560
1280
896
4300
4300
3600
2400
1100
720
320
3800
2800
1100
800
4200
3200
1800
640
0.08
0.08
0.04
0.04
0.04
0.03
0.02
0.016
0.012
0.1
0.1
0.06
0.04
0.02
0.02
0.016
0.016
0.01
0.01
0.08
0.08
0.04
0.04
0.016
0.012
0.1
0.08
0.06
0.14
0.14
0.12
0.08
0.06
0.04
0.02
0.16
0.12
0.08
0.06
0.18
0.14
0.08
0.06
<0.1PRFRAD
Depth ofcut
<0.2PRFRAD
SOLID END MILLS
Work material
Carbon steel,Alloy steel,Alloy Tool Steel,

Pre-hardened steel,
Precipitation hardeningstainless steel
(PRFRAD <1)
(PRFRAD> 1)
ap
PRFRAD:Radius
J215
MS PLUS END MILLS

CARBIDE
MP2XLB
Carbon steel,Alloy steel,Pre-hardened steel, Hardened steell
( 52HRC)
Work material
AISI 1055, AISI P21
Neck length
R
PRFRAD (mm) LU (mm)
R1
R1.25
SOLID END MILLS
R1.5
R1.75
R2
R2.5
R3
4
6
8
10
12
16
20
25
30
35
40
10
15
20
25
30
35
6
10
16
20
25
30
35
40
15
25
35
45
10
20
30
40
50
20
25
30
40
20
30
40
50
Revolution
(min-1)
Feed rate
(mm/min)
40000
40000
40000
40000
40000
32000
10000
10000
10000
10000
8000
36000
32000
26000
12000
8000
8000
32000
32000
32000
27000
21000
10000
6000
6000
27500
23000
10000
7500
24000
24000
20000
12000
8000
22000
22000
22000
22000
20000
20000
20000
20000
8000
8000
6000
5000
5000
3500
1000
1000
800
600
400
6000
4500
3200
1400
900
800
7000
7000
5000
3800
2700
700
700
600
4400
3600
1400
900
6000
3800
3000
1700
1000
6000
4400
3800
3600
6000
6000
4500
3000
AISI H13, AISI 420

Depth of cut
ap (mm)
0.1
0.1
0.1
0.08
0.08
0.05
0.04
0.04
0.02
0.02
0.01
0.12
0.1
0.07
0.06
0.04
0.02
0.15
0.15
0.1
0.1
0.08
0.08
0.06
0.04
0.13
0.1
0.08
0.04
0.2
0.15
0.1
0.1
0.05
0.2
0.2
0.15
0.1
0.2
0.2
0.15
0.15
Revolution
(min-1)
Feed rate
(mm/min)
32000
32000
32000
32000
32000
26000
10000
10000
10000
10000
8000
29000
26000
21000
8000
8000
8000
26000
26000
26000
22000
17000
6000
6000
6000
22000
18000
10000
7500
19000
19000
16000
12000
8000
18000
18000
18000
18000
16000
16000
16000
16000
5000
5000
3800
3200
3200
2200
800
800
640
480
320
3800
2900
2000
720
700
640
4500
4500
3200
2400
1700
560
560
480
2800
2200
1100
720
3800
2400
1900
1400
800
3800
2800
2400
2300
3800
3800
2800
1900
<0.1PRFRAD
Depth ofcut
<0.2PRFRAD
Depth of cut
ap (mm)
0.1
0.1
0.1
0.08
0.08
0.05
0.04
0.04
0.02
0.02
0.01
0.12
0.1
0.07
0.06
0.04
0.02
0.15
0.15
0.1
0.1
0.08
0.08
0.06
0.04
0.13
0.1
0.08
0.04
0.2
0.15
0.1
0.1
0.05
0.2
0.2
0.15
0.1
0.2
0.2
0.15
0.15
Revolution
(min-1)
Feed rate
(mm/min)
32000
32000
32000
32000
32000
26000
10000
10000
10000
10000
8000
29000
26000
21000
8000
8000
8000
22000
22000
22000
22000
17000
6000
6000
6000
18000
18000
10000
7500
16000
16000
16000
12000
8000
13000
13000
13000
13000
11000
11000
11000
11000
5000
5000
3800
3200
3200
2200
800
800
640
480
320
3800
2900
2000
720
700
510
3800
3800
2700
2400
1700
560
560
480
2300
2200
1100
720
3200
2000
1900
1400
800
2800
2000
1700
1600
2600
2600
2000
1300
Depth of cut
ap (mm)
0.2
0.2
0.2
0.16
0.16
0.1
0.08
0.08
0.04
0.04
0.02
0.24
0.2
0.14
0.12
0.08
0.04
0.3
0.3
0.2
0.2
0.16
0.16
0.12
0.08
0.26
0.2
0.16
0.08
0.4
0.3
0.2
0.2
0.1
0.4
0.4
0.3
0.2
0.4
0.4
0.3
0.3
(PRFRAD <1)
(PRFRAD> 1)
ap
PRFRAD:Radius
J216
MSTAR END MILLS
MS2SB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
UWC
Austenitic
Stainless Steel
Titanium Alloy,
MS
Copper Alloy
30
CARBIDE
Aluminium Alloy
Type1
DCON(h6)
APMX
DC
LF
0.005
PRFRAD
0.007
Type2
DCON(h6)
0.1<PRFRAD<3 4<PRFRAD<6
APMX
LF
0.2<DC<12
BALL
PRFRAD
0
- 0.020
h6
SQUARE
DC
15

0
- 0.005
0
- 0.006
0
- 0.008
DC
APMX
LF
DCON
Stock
MS2SBR0010S04
MS2SBR0010S06
MS2SBR0015S04
MS2SBR0015S06
MS2SBR0020S04
MS2SBR0020S06
MS2SBR0025S04
MS2SBR0025S06
MS2SBR0030S04
MS2SBR0030S06
MS2SBR0035S04
MS2SBR0040S04
MS2SBR0040S06
MS2SBR0045S04
MS2SBR0050S04
MS2SBR0050S06
MS2SBR0060S04
MS2SBR0060S06
MS2SBR0070S04
MS2SBR0070S06
MS2SBR0075S04
MS2SBR0075S06
MS2SBR0080S04
MS2SBR0080S06
MS2SBR0090S04
MS2SBR0090S06
MS2SBR0100S04
MS2SBR0100S06
MS2SBR0125S04
MS2SBR0125S06
MS2SBR0150S06
MS2SBR0200S06
MS2SBR0250S06
MS2SBR0300S06
0.1
0.1
0.15
0.15
0.2
0.2
0.25
0.25
0.3
0.3
0.35
0.4
0.4
0.45
0.5
0.5
0.6
0.6
0.7
0.7
0.75
0.75
0.8
0.8
0.9
0.9
1
1
1.25
1.25
1.5
2
2.5
3
0.2
0.2
0.3
0.3
0.4
0.4
0.5
0.5
0.6
0.6
0.7
0.8
0.8
0.9
1
1
1.2
1.2
1.4
1.4
1.5
1.5
1.6
1.6
1.8
1.8
2
2
2.5
2.5
3
4
5
6
0.3
0.3
0.5
0.5
0.6
0.6
0.8
0.8
0.9
0.9
1.1
1.2
1.2
1.4
1.5
1.5
1.8
1.8
2.1
2.1
2.3
2.3
2.4
2.4
2.7
2.7
3
3
3.8
3.8
4.5
6
7.5
9
45
50
45
50
45
50
45
50
45
50
45
45
50
45
45
50
45
50
45
50
45
50
45
50
45
50
50
50
50
50
70
70
80
80
4
6
4
6
4
6
4
6
4
6
4
4
6
4
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
TAPER
PRFRAD
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute ball nose end mill for general use.
J217
MSTAR END MILLS
MS2SB
PRFRAD
DC
APMX
LF
DCON
No. of
Flutes
Stock
MS2SBR0400S08
MS2SBR0500S10
MS2SBR0600S12
4
5
6
8
10
12
12
15
18
90
100
110
8
10
12
2
2
2
RADIUS
TAPER
SOLID END MILLS
J218
Unit : mm
Order Number
BALL
SQUARE
CARBIDE
a
a
Type
2
2
2
MS2MB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
UWC
Austenitic
Stainless Steel
Titanium Alloy,
MS
Copper Alloy
30
CARBIDE
Aluminium Alloy
Type1
DCON(h6)
APMX
0.25<PRFRAD<3 4<PRFRAD<6
0.005
PRFRAD
0.007
Type2
DCON(h6)
DC
LF
APMX
LF
0.5<DC<12
BALL
PRFRAD
0
- 0.020
h6
SQUARE
DC
15

0
- 0.005
0
- 0.006
0
- 0.008
DC
APMX
LF
DCON
Stock
MS2MBR0025
MS2MBR0030
MS2MBR0040
MS2MBR0050
MS2MBR0060
MS2MBR0070
MS2MBR0075
MS2MBR0080
MS2MBR0090
MS2MBR0100
MS2MBR0125
MS2MBR0150S03
MS2MBR0150
MS2MBR0175
MS2MBR0200S04
MS2MBR0200
MS2MBR0250
MS2MBR0300
MS2MBR0400
MS2MBR0500
MS2MBR0600
0.25
0.3
0.4
0.5
0.6
0.7
0.75
0.8
0.9
1
1.25
1.5
1.5
1.75
2
2
2.5
3
4
5
6
0.5
0.6
0.8
1
1.2
1.4
1.5
1.6
1.8
2
2.5
3
3
3.5
4
4
5
6
8
10
12
1
1.2
1.6
2.5
2.5
3
4
4
5
6
6
8
8
8
8
8
12
12
14
18
22
45
45
45
45
45
45
45
45
45
50
50
70
70
70
70
70
80
80
90
100
110
4
4
4
4
4
4
4
4
4
4
4
3
6
6
4
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
2
2
2
2
TAPER
PRFRAD
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute ball nose end mill for general use.
J219
MSTAR END MILLS

CARBIDE
MS2SB
MS2MB


material
AISI H13
%>15
%<15
R
PRFRAD
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
R 0.1
R 0.15
R 0.2
R 0.25
R 0.3
R 0.4
R 0.5
R 0.75
R1
R 1.25
R 1.5
R2
R 2.5
R3
R4
R5
R6
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
32000
25000
21000
16000
13000
9000
300
500
1600
2400
3200
4800
5600
6500
6500
7000
7500
7500
6000
5800
4500
3600
2500
40000
40000
40000
40000
40000
40000
40000
40000
39000
33000
27000
20000
16000
13000
10000
8000
6000
250
350
1200
1400
1600
2400
3200
4000
4700
4500
4300
3600
2900
2600
2000
1700
1300
Depth of
cut
Depth of cut
(mm)
0.003
0.007
0.02
0.025
0.03
0.05
0.06
0.09
0.11
0.12
0.13
0.15
0.20
0.25
0.30
0.50
0.50
%>15
%<15
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
40000
40000
40000
40000
40000
40000
40000
40000
40000
36000
32000
25000
20000
17000
13000
10000
7200
300
500
1300
1900
2500
4000
5600
6500
6500
6500
6000
6000
5400
4700
3600
2900
2000
40000
40000
40000
40000
40000
40000
40000
32000
31000
26000
22000
16000
13000
10000
8000
6400
4800
250
350
950
1100
1300
1900
3000
3200
3500
3500
3400
2700
2300
2000
1500
1200
1000
Depth of cut
(mm)
0.003
0.007
0.015
0.020
0.025
0.04
0.05
0.08
0.11
0.12
0.13
0.15
0.20
0.25
0.30
0.50
0.50
<0.2PRFRAD
< Please
SOLID END MILLS
PRFRAD:Radius

End mill
pf
J220
ap
PRFRAD
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
30
Copper Alloy
DN
Hardened Steel
( < 55HRC)
MS
UWC
CARBIDE
Aluminium Alloy
B2
Inclined angle
0.2 < DC < 6
PRFRAD
Type2
APMX
LU
LF
0
- 0.020
h6
BALL
0.005
LF
DCON(h6)
0.1<PRFRAD<3
15
DC
Effective
length
Effective length
for inclined angle
APMX
LU
DN
PRFRAD
DCON(h6)
DC
Type1
SQUARE
MS2XLB
4 < DCON < 6

0
- 0.005
LU
DN
B2
LF
DCON
MS2XLBR0010N005
MS2XLBR0010N005S06
MS2XLBR0010N008S06
MS2XLBR0010N010
MS2XLBR0010N010S06
MS2XLBR0010N013
MS2XLBR0010N013S06
MS2XLBR0010N015
MS2XLBR0010N015S06
MS2XLBR0010N018
MS2XLBR0010N018S06
MS2XLBR0010N020
MS2XLBR0010N020S06
MS2XLBR0010N025
MS2XLBR0010N030
MS2XLBR0015N008S06
MS2XLBR0015N010
MS2XLBR0015N010S06
MS2XLBR0015N012S06
MS2XLBR0015N015
MS2XLBR0015N015S06
MS2XLBR0015N020
MS2XLBR0015N020S06
MS2XLBR0015N025
MS2XLBR0015N030
MS2XLBR0015N040
MS2XLBR0020N010
MS2XLBR0020N010S06
MS2XLBR0020N012S06
MS2XLBR0020N015
MS2XLBR0020N015S06
MS2XLBR0020N020
MS2XLBR0020N020S06
MS2XLBR0020N025
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.8
1
1
1.25
1.25
1.5
1.5
1.75
1.75
2
2
2.5
3
0.8
1
1
1.2
1.5
1.5
2
2
2.5
3
4
1
1
1.2
1.5
1.5
2
2
2.5
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
14.1
14.4
14.1
13.3
13.8
12.9
13.6
12.5
13.3
12.2
13.1
11.9
12.8
11.3
10.7
14.1
13.3
13.9
13.7
12.5
13.3
11.9
12.8
11.2
10.7
9.7
13.4
13.9
13.7
12.6
13.4
11.9
12.8
11.2
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
6
6
4
6
4
6
4
6
4
6
4
6
4
4
6
4
6
6
4
6
4
6
4
4
4
4
6
6
4
6
4
6
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
0.5
0.5
0.8
1
1
1.3
1.3
1.5
1.5
1.8
1.8
2.1
2.1
2.6
3.1
0.8
1
1
1.2
1.5
1.5
2.1
2.1
2.6
3.1
4.2
1
1
1.2
1.5
1.5
2
2
2.6
0.5
0.5
0.8
1.1
1.1
1.3
1.3
1.6
1.6
1.9
1.9
2.2
2.2
2.7
3.2
0.8
1.1
1.1
1.3
1.6
1.6
2.2
2.2
2.7
3.2
4.3
1
1
1.3
1.6
1.6
2.1
2.1
2.7
0.6
0.6
0.9
1.2
1.2
1.5
1.5
1.7
1.7
2
2
2.3
2.3
2.9
3.5
0.9
1.2
1.2
1.4
1.7
1.7
2.3
2.3
2.9
3.5
4.6
1.1
1.1
1.4
1.7
1.7
2.3
2.3
2.9
0.6
0.6
1
1.3
1.3
1.6
1.6
1.9
1.9
2.2
2.2
2.5
2.5
3.1
3.7
1
1.3
1.3
1.5
1.9
1.9
2.5
2.5
3.1
3.7
5
1.2
1.2
1.5
1.8
1.8
2.5
2.5
3.1
TAPER
APMX
SOLID END MILLS
DC
Type
PRFRAD
Stock
Order Number
No. of Flutes
Unit : mm
RADIUS
a 2 flute long neck ball nose end mill.
J221
MSTAR END MILLS
MS2XLB
DC
APMX
MS2XLBR0020N025S06
MS2XLBR0020N030
MS2XLBR0020N030S06
MS2XLBR0020N035
MS2XLBR0020N040
MS2XLBR0020N045
MS2XLBR0020N050
MS2XLBR0020N055
MS2XLBR0020N060
MS2XLBR0025N015
MS2XLBR0025N015S06
MS2XLBR0025N020
MS2XLBR0025N020S06
MS2XLBR0025N025
MS2XLBR0025N025S06
MS2XLBR0025N030
MS2XLBR0025N030S06
MS2XLBR0025N035
MS2XLBR0025N035S06
MS2XLBR0025N040
MS2XLBR0025N040S06
MS2XLBR0025N045
MS2XLBR0025N045S06
MS2XLBR0025N050
MS2XLBR0025N050S06
MS2XLBR0025N055
MS2XLBR0025N055S06
MS2XLBR0025N060
MS2XLBR0025N060S06
MS2XLBR0025N070
MS2XLBR0025N070S06
MS2XLBR0025N080
MS2XLBR0025N080S06
MS2XLBR0025N100
MS2XLBR0025N100S06
MS2XLBR0030N018S06
MS2XLBR0030N020
MS2XLBR0030N020S06
MS2XLBR0030N025
MS2XLBR0030N025S06
MS2XLBR0030N030
MS2XLBR0030N030S06
MS2XLBR0030N035
MS2XLBR0030N035S06
MS2XLBR0030N040
MS2XLBR0030N040S06
MS2XLBR0030N045
MS2XLBR0030N045S06
MS2XLBR0030N050
MS2XLBR0030N050S06
MS2XLBR0030N060
MS2XLBR0030N060S06
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
J222
LU
2.5
3
3
3.5
4
4.5
5
5.5
6
1.5
1.5
2
2
2.5
2.5
3
3
3.5
3.5
4
4
4.5
4.5
5
5
5.5
5.5
6
6
7
7
8
8
10
10
1.8
2
2
2.5
2.5
3
3
3.5
3.5
4
4
4.5
4.5
5
5
6
6
DN
B2
LF
DCON
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
12.4
10.7
11.9
10.2
9.7
9.3
8.9
8.5
8.2
12.6
13.4
11.9
12.9
11.2
12.4
10.6
11.9
10.1
11.5
9.6
11.1
9.2
10.7
8.8
10.4
8.4
10.1
8.1
9.7
7.5
9.2
7
8.7
6.2
7.8
13
11.8
12.8
11.1
12.3
10.5
11.8
10
11.4
9.5
11
9.1
10.6
8.7
10.3
8
9.7
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
6
4
6
4
4
4
4
4
4
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Effective length
for inclined angle
Type
PRFRAD
Stock
Order Number
Unit : mm
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
1 2.6 2.7 2.9 3.1

1 3.1 3.2 3.4 3.7
1 3.1 3.2 3.4 3.7
1 3.6 3.7 4
4.3
1 4.1 4.3 4.6 4.9
1 4.7 4.8 5.2 5.6
1 5.2 5.3 5.7 6.2
1 5.7 5.9 6.3 6.8
1 6.2 6.4 6.9 7.4
1 1.5 1.6 1.7 1.8
1 1.5 1.6 1.7 1.8
1 2
2.1 2.3 2.4
1 2
2.1 2.3 2.4
1 2.6 2.7 2.9 3.1
1 2.6 2.7 2.9 3.1
1 3.1 3.2 3.4 3.7
1 3.1 3.2 3.4 3.7
1 3.6 3.7 4
4.3
1 3.6 3.7 4
4.3
1 4.1 4.3 4.6 4.9
1 4.1 4.3 4.6 4.9
1 4.6 4.8 5.2 5.6
1 4.6 4.8 5.2 5.6
1 5.2 5.3 5.7 6.2
1 5.2 5.3 5.7 6.2
1 5.7 5.9 6.3 6.8
1 5.7 5.9 6.3 6.8
1 6.2 6.4 6.9 7.4
1 6.2 6.4 6.9 7.4
1 7.2 7.5 8
8.7
1 7.2 7.5 8
8.7
1 8.3 8.5 9.2 9.9
1 8.3 8.5 9.2 9.9
1 10.3 10.7 11.5 12.4
1 10.3 10.7 11.5 12.4
1 1.9 1.9 2.1 2.3
1 2.1 2.2 2.3 2.5
1 2.1 2.2 2.3 2.5
1 2.6 2.7 2.9 3.1
1 2.6 2.7 2.9 3.1
1 3.1 3.3 3.5 3.8
1 3.1 3.3 3.5 3.8
1 3.6 3.8 4.1 4.4
1 3.6 3.8 4.1 4.4
1 4.2 4.3 4.6 5
1 4.2 4.3 4.6 5
1 4.7 4.9 5.2 5.6
1 4.7 4.9 5.2 5.6
1 5.2 5.4 5.8 6.2
1 5.2 5.4 5.8 6.2
1 6.3 6.5 6.9 7.5
1 6.3 6.5 6.9 7.5
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
30'
CARBIDE
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
7
8
8
9
10
10
11
12
2
2
2.4
3
3
4
4
5
6
6
7
8
8
10
10
12
3
3
4
4
5
5
6
6
7
8
8
9
10
10
12
12
14
16
16
18
20
20
3.6
6
6
8
8
10
LF
DCON
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.14
1.14
1.14
1.14
1.14
1.14
7.4
6.9
8.6
6.4
6
7.8
5.7
5.4
11.7
12.8
12.4
10.4
11.8
9.4
11
8.5
7.8
9.6
7.2
6.7
8.5
5.9
7.7
5.2
10.1
11.6
9.1
10.8
8.2
10.1
7.5
9.4
6.9
6.4
8.3
6
5.6
7.5
5
6.8
4.5
4.1
5.7
3.7
3.4
5
11.1
7.3
9.3
6.2
8.2
5.4
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
55
50
55
60
55
55
60
50
50
50
50
50
50
4
4
6
4
4
6
4
4
4
6
6
4
6
4
6
4
4
6
4
4
6
4
6
4
4
6
4
6
4
6
4
6
4
4
6
4
4
6
4
6
4
4
6
4
4
6
6
4
6
4
6
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
7.3
8.3
8.3
9.4
10.4
10.4
11.4
12.5
2.1
2.1
2.5
3.1
3.1
4.2
4.2
5.2
6.3
6.3
7.3
8.3
8.3
10.4
10.4
12.5
3.2
3.2
4.2
4.2
5.3
5.3
6.3
6.3
7.4
8.4
8.4
9.5
10.5
10.5
12.6
12.6
14.7
16.8
16.8
18.9
20.9
20.9
3.8
6.3
6.3
8.4
8.4
10.5
7.5
8.6
8.6
9.7
10.8
10.8
11.8
12.9
2.2
2.2
2.6
3.3
3.3
4.3
4.3
5.4
6.5
6.5
7.5
8.6
8.6
10.8
10.8
12.9
3.3
3.3
4.4
4.4
5.5
5.5
6.6
6.6
7.7
8.8
8.8
9.9
10.9
10.9
13.1
13.1
15.2
17.4
17.4
19.5
21.6
21.6
4
6.6
6.6
8.8
8.8
10.9
8.1
9.2
9.2
10.4
11.5
11.5
12.7
13.8
2.3
2.3
2.8
3.5
3.5
4.6
4.6
5.8
6.9
6.9
8.1
9.2
9.2
11.5
11.5
13.8
3.6
3.6
4.8
4.8
6
6
7.1
7.1
8.3
9.4
9.4
10.6
11.7
11.7
14
14
16.3
18.6
18.6
20.9
23.2
23.2
4.3
7.1
7.1
9.4
9.4
11.7
8.7
10
10
11.2
12.5
12.5
13.7
15
2.5
2.5
3
3.7
3.7
5
5
6.2
7.5
7.5
8.7
10
10
12.4
12.4
14.9
3.9
3.9
5.2
5.2
6.4
6.4
7.7
7.7
8.9
10.2
10.2
11.4
12.6
12.6
15.1
15.1
17.6
20.1
20.1
22.6
25.1
25.1
4.7
7.6
7.6
10.1
10.1
12.6
SQUARE
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
B2
BALL
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
DN
RADIUS
MS2XLBR0030N070
MS2XLBR0030N080
MS2XLBR0030N080S06
MS2XLBR0030N090
MS2XLBR0030N100
MS2XLBR0030N100S06
MS2XLBR0030N110
MS2XLBR0030N120
MS2XLBR0040N020
MS2XLBR0040N020S06
MS2XLBR0040N024S06
MS2XLBR0040N030
MS2XLBR0040N030S06
MS2XLBR0040N040
MS2XLBR0040N040S06
MS2XLBR0040N050
MS2XLBR0040N060
MS2XLBR0040N060S06
MS2XLBR0040N070
MS2XLBR0040N080
MS2XLBR0040N080S06
MS2XLBR0040N100
MS2XLBR0040N100S06
MS2XLBR0040N120
MS2XLBR0050N030
MS2XLBR0050N030S06
MS2XLBR0050N040
MS2XLBR0050N040S06
MS2XLBR0050N050
MS2XLBR0050N050S06
MS2XLBR0050N060
MS2XLBR0050N060S06
MS2XLBR0050N070
MS2XLBR0050N080
MS2XLBR0050N080S06
MS2XLBR0050N090
MS2XLBR0050N100
MS2XLBR0050N100S06
MS2XLBR0050N120
MS2XLBR0050N120S06
MS2XLBR0050N140
MS2XLBR0050N160
MS2XLBR0050N160S06
MS2XLBR0050N180
MS2XLBR0050N200
MS2XLBR0050N200S06
MS2XLBR0060N036S06
MS2XLBR0060N060
MS2XLBR0060N060S06
MS2XLBR0060N080
MS2XLBR0060N080S06
MS2XLBR0060N100
LU
TAPER
APMX
SOLID END MILLS
DC
Type
PRFRAD
Stock
Order Number
No. of Flutes
Unit : mm
J223
MSTAR END MILLS
MS2XLB
DC
APMX
MS2XLBR0060N100S06
MS2XLBR0060N120
MS2XLBR0060N120S06
MS2XLBR0060N140
MS2XLBR0060N160
MS2XLBR0060N160S06
MS2XLBR0060N180
MS2XLBR0060N240
MS2XLBR0070N080
MS2XLBR0070N120
MS2XLBR0070N160
MS2XLBR0075N045S06
MS2XLBR0075N060
MS2XLBR0075N060S06
MS2XLBR0075N075S06
MS2XLBR0075N080
MS2XLBR0075N080S06
MS2XLBR0075N100
MS2XLBR0075N100S06
MS2XLBR0075N120
MS2XLBR0075N120S06
MS2XLBR0075N140
MS2XLBR0075N140S06
MS2XLBR0075N160
MS2XLBR0075N160S06
MS2XLBR0075N180
MS2XLBR0075N200
MS2XLBR0075N200S06
MS2XLBR0075N220
MS2XLBR0075N300
MS2XLBR0080N080
MS2XLBR0080N120
MS2XLBR0080N160
MS2XLBR0080N200
MS2XLBR0090N080
MS2XLBR0090N120
MS2XLBR0090N160
MS2XLBR0090N200
MS2XLBR0100N040
MS2XLBR0100N040S06
MS2XLBR0100N060
MS2XLBR0100N060S06
MS2XLBR0100N080
MS2XLBR0100N080S06
MS2XLBR0100N100
MS2XLBR0100N100S06
MS2XLBR0100N120
MS2XLBR0100N120S06
MS2XLBR0100N140
MS2XLBR0100N140S06
MS2XLBR0100N160
MS2XLBR0100N160S06
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.8
0.8
0.8
0.8
0.9
0.9
0.9
0.9
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
2
2
2
2
2
2
2
2
2
2
2
2
2
2
LU
10
12
12
14
16
16
18
24
8
12
16
4.5
6
6
7.5
8
8
10
10
12
12
14
14
16
16
18
20
20
22
30
8
12
16
20
8
12
16
20
4
4
6
6
8
8
10
10
12
12
14
14
16
16
DN
B2
LF
DCON
1.14
1.14
1.14
1.14
1.14
1.14
1.14
1.14
1.34
1.34
1.34
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.54
1.54
1.54
1.54
1.74
1.74
1.74
1.74
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
7.4
4.8
6.7
4.3
3.9
5.6
3.5
2.8
6
4.6
3.7
10.2
7
9.2
8.3
5.9
8.1
5.1
7.2
4.4
6.5
4
5.9
3.6
5.4
3.3
3
4.6
2.8
2.1
5.8
4.3
3.5
2.9
5.5
4.1
3.3
2.7
8.2
10.6
6.4
9
5.3
7.8
4.5
6.9
3.9
6.1
3.4
5.6
3.1
5.1
50
50
55
50
55
60
55
65
50
50
55
50
50
50
50
50
50
50
50
50
55
50
55
55
60
55
55
60
60
70
50
50
55
55
50
50
55
55
50
50
50
50
50
50
50
50
50
55
50
55
55
60
6
4
6
4
4
6
4
4
4
4
4
6
4
6
6
4
6
4
6
4
6
4
6
4
6
4
4
6
4
4
4
4
4
4
4
4
4
4
4
6
4
6
4
6
4
6
4
6
4
6
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Type
PRFRAD
Stock
Order Number
Unit : mm
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
10.5
12.6
12.6
14.7
16.8
16.8
18.8
25.1
8.4
12.6
16.8
4.7
6.3
6.3
7.9
8.4
8.4
10.5
10.5
12.6
12.6
14.7
14.7
16.8
16.8
18.8
20.9
20.9
23
31.2
8.4
12.6
16.8
20.9
8.4
12.6
16.8
20.9
4.1
4.1
6.2
6.2
8.3
8.3
10.4
10.4
12.5
12.5
14.6
14.6
16.7
16.7
10.9
13.1
13.1
15.2
17.3
17.3
19.5
25.9
8.8
13.1
17.3
5
6.6
6.6
8.2
8.8
8.8
10.9
10.9
13.1
13.1
15.2
15.2
17.3
17.3
19.5
21.6
21.6
23.8
32.3
8.8
13.1
17.3
21.6
8.8
13
17.3
21.6
4.3
4.3
6.5
6.5
8.7
8.7
10.8
10.8
12.9
12.9
15.1
15.1
17.2
17.2
11.7
14
14
16.3
18.6
18.6
20.9
27.8
9.4
14
18.6
5.4
7.1
7.1
8.8
9.4
9.4
11.7
11.7
14
14
16.3
16.3
18.6
18.6
20.9
23.2
23.2
25.5
34.7
9.4
14
18.6
23.2
9.4
14
18.6
23.2
4.6
4.6
6.9
6.9
9.2
9.2
11.5
11.5
13.8
13.8
16.1
16.1
18.4
18.4
12.6
15.1
15.1
17.6
20.1
20.1
22.6
10.1
15.1
20.1
5.7
7.6
7.6
9.5
10.1
10.1
12.6
12.6
15.1
15.1
17.6
17.6
20
20
22.5
25
*
*
10.1
15.1
20
10.1
15
20
4.9
4.9
7.4
7.4
9.9
9.9
12.4
12.4
14.9
14.9
17.4
17.4
19.9
19.9
* No interference
a
J224
CARBIDE
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
18
18
20
20
22
25
25
30
30
35
35
6
7.5
10
12.5
16
20
25
30
35
8
10
12
14
16
20
25
30
35
40
10
12
14
16
20
25
30
35
40
45
50
20
25
30
35
30
50
LF
DCON
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
4.9
4.9
4.9
4.9
5.85
5.85
2.8
4.7
2.5
4.3
2.3
2.1
3.7
1.8
3.2
1.6
2.8
8.6
7.7
6.5
5.6
4.7
4
3.3
2.9
2.5
7
6
5.3
4.7
4.3
3.6
3
2.6
2.2
2
4.8
4.1
3.6
3.2
2.7
2.2
1.8
1.6
1.4
1.3
1.2
1.5
1.2
1
0.9
55
60
60
60
60
65
65
70
70
70
80
50
50
50
50
60
60
65
70
80
60
60
60
60
60
70
70
70
80
90
70
70
70
70
70
70
70
80
90
90
100
70
70
80
80
80
120
4
6
4
6
4
4
6
4
6
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
18.7
18.7
20.8
20.8
22.9
26
26
31.1
31.1
36.3
36.3
6.2
7.8
10.4
13
16.7
20.8
26
31.1
36.3
8.3
10.4
12.5
14.6
16.6
20.8
26
31.1
36.3
41.5
10.4
12.5
14.6
16.6
20.8
25.9
31.1
36.3
41.4
46.6
51.8
20.7
25.9
31.1
36.3
19.4
19.4
21.5
21.5
23.6
26.8
26.8
32.2
32.2
37.5
37.5
6.5
8.1
10.8
13.5
17.2
21.5
26.8
32.2
37.5
8.6
10.8
12.9
15
17.2
21.5
26.8
32.2
37.5
42.9
10.7
12.9
15
17.1
21.4
26.8
32.1
37.5
42.8
48.2
53.5
21.4
26.7
20.7
20.7 22.3
23
23 24.8
25.3
28.8
28.8 31
SQUARE
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
B2
*
*
*
*
34.5 37.3
40.3
6.9
8.6
11.5
14.4
18.4
23
28.7
34.5
40.2
9.2
11.5
13.8
16.1
18.4
23
28.7
34.5
40.2
11.4
13.7
16
18.3
22.9
28.6
7.4
9.2
12.3
15.4
19.8
24.8
31
*
*
9.8
12.3
14.8
17.3
19.7
24.7
*
*
*
*
12.2
14.6
17.1
19.6
BALL
1
1
1
1
1
1
1
1
1
1
1
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
3
3
DN
RADIUS
MS2XLBR0100N180
MS2XLBR0100N180S06
MS2XLBR0100N200
MS2XLBR0100N200S06
MS2XLBR0100N220
MS2XLBR0100N250
MS2XLBR0100N250S06
MS2XLBR0100N300
MS2XLBR0100N300S06
MS2XLBR0100N350
MS2XLBR0100N350S06
MS2XLBR0125N060S06
MS2XLBR0125N075S06
MS2XLBR0125N100S06
MS2XLBR0125N125S06
MS2XLBR0125N160S06
MS2XLBR0125N200S06
MS2XLBR0125N250S06
MS2XLBR0125N300S06
MS2XLBR0125N350S06
MS2XLBR0150N080
MS2XLBR0150N100
MS2XLBR0150N120
MS2XLBR0150N140
MS2XLBR0150N160
MS2XLBR0150N200
MS2XLBR0150N250
MS2XLBR0150N300
MS2XLBR0150N350
MS2XLBR0150N400
MS2XLBR0200N100
MS2XLBR0200N120
MS2XLBR0200N140
MS2XLBR0200N160
MS2XLBR0200N200
MS2XLBR0200N250
MS2XLBR0200N300
MS2XLBR0200N350
MS2XLBR0200N400
MS2XLBR0200N450
MS2XLBR0200N500
MS2XLBR0250N200
MS2XLBR0250N250
MS2XLBR0250N300
MS2XLBR0250N350
MS2XLBR0300N300
MS2XLBR0300N500
LU
TAPER
APMX
SOLID END MILLS
DC
Type
PRFRAD
Stock
Order Number
No. of Flutes
Unit : mm
*
*
* *
* *
* *
* *
* *
* *
* *
* * *
* * *
* * * *
* *
* *No interference
*
J225
MSTAR END MILLS

CARBIDE
MS2XLB
Work material

Alloy steel, Pre-hardened steel
AISI P20, AISI P21
R
Neck length Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut
PRFRAD (mm) LU (mm) (min-1) (mm/min) ap (mm) (min-1) (mm/min) ap (mm)
R 0.1
R 0.15
R 0.2
SOLID END MILLS
R 0.25
R 0.3
R 0.4
R 0.5
0.5
1
1.5
2
2.5
3
1
1.5
2
2.5
3
4
1
2
3
4
5
6
2
3
4
5
6
7
8
10
2
3
4
5
6
7
8
9
10
11
12
2
3
4
5
6
7
8
10
12
3
4
6
8
50000
50000
40000
40000
40000
30000
50000
50000
50000
40000
40000
30000
50000
50000
50000
40000
40000
30000
50000
50000
45000
45000
36000
32000
32000
26000
50000
50000
44000
37000
37000
35000
35000
30000
30000
22000
22000
50000
50000
50000
35000
35000
30000
30000
30000
22000
40000
40000
35000
30000
400
400
300
200
100
50
600
600
600
400
300
200
1800
1300
900
600
400
200
2500
1500
1200
900
600
400
300
200
3500
3500
2500
1200
1000
750
600
500
500
300
200
4400
4000
4000
2400
2400
1500
1500
700
500
4000
4000
3000
2000
0.003
0.002
0.001
0.001
0.001
0.001
0.007
0.005
0.003
0.003
0.002
0.002
0.015
0.01
0.005
0.004
0.003
0.002
0.02
0.015
0.01
0.007
0.006
0.005
0.003
0.002
0.03
0.03
0.02
0.01
0.008
0.008
0.006
0.004
0.003
0.002
0.002
0.04
0.04
0.02
0.02
0.02
0.015
0.01
0.008
0.006
0.05
0.05
0.03
0.02
Work material
AISI H13
50000
50000
40000
40000
40000
30000
50000
50000
50000
40000
40000
30000
50000
50000
50000
40000
40000
30000
50000
50000
45000
45000
36000
32000
32000
26000
50000
50000
44000
37000
37000
35000
35000
30000
30000
22000
22000
50000
50000
50000
35000
35000
30000
30000
30000
22000
40000
40000
35000
30000
320
320
240
160
80
40
480
480
480
320
240
160
1400
1000
700
480
320
160
2000
1200
950
700
480
320
240
160
2800
2800
2000
950
800
600
480
400
400
240
160
3500
3200
3200
1900
1900
1200
1200
560
400
3200
3200
2400
1600
0.003
0.002
0.001
0.001
0.001
0.001
0.007
0.005
0.003
0.003
0.002
0.002
0.015
0.01
0.005
0.004
0.003
0.002
0.02
0.015
0.01
0.007
0.006
0.005
0.003
0.002
0.03
0.03
0.02
0.01
0.008
0.008
0.006
0.004
0.003
0.002
0.002
0.04
0.04
0.02
0.02
0.02
0.015
0.01
0.008
0.006
0.05
0.05
0.03
0.02
R
Neck length Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut
PRFRAD (mm) LU (mm) (min-1) (mm/min) ap (mm) (min-1) (mm/min) ap (mm)
R 0.5
R 0.6
R 0.75
R1
R 1.5
R2
R 2.5
R3
<0.1PRFRAD
<0.2PRFRAD
Depth of cut

Alloy steel, Pre-hardened steel
AISI P20, AISI P21
AISI H13
10
12
14
16
18
20
3.6
6
8
10
12
18
24
6
8
10
12
16
20
30
4
6
8
10
12
16
20
25
30
35
8
10
16
20
25
30
35
40
10
20
30
40
50
20
25
30
35
30
50
20000
20000
18000
18000
13000
13000
40000
40000
40000
27000
16000
15000
11000
40000
40000
40000
32000
15000
12000
9000
40000
40000
40000
40000
40000
32000
10000
10000
10000
10000
32000
32000
32000
27000
21000
6000
6000
6000
24000
24000
20000
12000
8000
22000
22000
22000
22000
20000
20000
1000
1000
600
500
300
250
4400
4400
4000
1900
1400
700
300
6000
6000
5000
3400
1400
900
400
8000
8000
6000
5000
5000
3500
1000
1000
800
600
7000
7000
5000
3800
2700
700
700
600
6000
3800
3000
1700
1000
6000
4400
3800
3600
6000
3000
0.01
0.01
0.008
0.008
0.005
0.005
0.06
0.04
0.04
0.02
0.02
0.008
0.006
0.07
0.07
0.06
0.04
0.03
0.02
0.01
0.1
0.1
0.1
0.08
0.08
0.05
0.04
0.04
0.02
0.02
0.15
0.15
0.1
0.1
0.08
0.08
0.06
0.04
0.2
0.15
0.1
0.1
0.05
0.2
0.2
0.15
0.1
0.2
0.15
20000
20000
18000
18000
13000
13000
40000
40000
40000
27000
16000
15000
11000
36000
36000
36000
29000
15000
12000
9000
32000
32000
32000
32000
32000
26000
10000
10000
10000
10000
26000
26000
26000
22000
17000
6000
6000
6000
19000
19000
16000
12000
8000
18000
18000
18000
18000
16000
16000
800
800
480
400
240
200
3500
3500
3200
1500
1100
560
240
4300
4300
3600
2400
1100
720
320
5000
5000
3800
3200
3200
2200
800
800
640
480
4500
4500
3200
2400
1700
560
560
480
3800
2400
1900
1400
800
3800
2800
2400
2300
3800
1900
0.01
0.01
0.008
0.008
0.005
0.005
0.06
0.04
0.04
0.02
0.02
0.008
0.006
0.07
0.07
0.06
0.04
0.03
0.02
0.01
0.1
0.1
0.1
0.08
0.08
0.05
0.04
0.04
0.02
0.02
0.15
0.15
0.1
0.1
0.08
0.08
0.06
0.04
0.2
0.15
0.1
0.1
0.05
0.2
0.2
0.15
0.1
0.2
0.15
(PRFRAD<1)
(PRFRAD> 1)
ap
PRFRAD:Radius
J226
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
UWC
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
15
DC
DN
220
VF
DCON(h6)
Type1
PRFRAD
LU
BALL
LF
1<PRFRAD<3
SQUARE
VF2WB
0.01
DCON=6
h6
0
- 0.008
Order Number
PRFRAD
DC
LU
DN
LF
DCON
No. of
Flutes
Stock
Unit : mm
VF2WBR0100N060
VF2WBR0150N080
VF2WBR0200N100
VF2WBR0300N120
1
1.5
2
3
2
3
4
6
6
8
10
12
1.6
2.4
3.2
4.8
60
60
60
80
6
6
6
6
2
2
2
2
Type
1
1
1
1
a
a
a
TAPER
and complex geometries using a 5-axis machine.
RADIUS
a Ball nose end mill suitable for machining of undercut geometries
Work
material


Pre-hardened steel

Titanium alloy
AISI H13
Revolution
R
(min-1)
PRFRAD (mm)
R1
R1.5
R2
R3
40000
32000
24000
16000
Feed rate Depth of cut Revolution

(mm)
(min-1)
(mm/min)
5000
5000
3800
2800
0.07
0.12
0.15
0.20
Depth of
cut
40000
32000
24000
16000

(mm)
(mm/min)
(min-1)
5000
5000
3800
2800
0.06
0.11
0.13
0.18
32000
26000
20000
13000

(mm)
(mm/min)
(min-1)
2500
2500
2000
1500
0.05
0.10
0.12
0.15
32000
26000
20000
13000
Feed rate Depth of cut

(mm)
(mm/min)
3000
3000
2800
2100
SOLID END MILLS
0.03
0.07
0.10
0.12
<0.05PRFRAD (PRFRAD=1)
<0.1PRFRAD (PRFRAD>1)
< Please
PRFRAD:Radius
J227
VF2SSB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
VF
Copper Alloy
Aluminium Alloy
Type1
PRFRAD
APMX
LU
BALL
DN
0.5<PRFRAD<6
0.005
Type2
PRFRAD
1 < DC < 12
APMX
LU
0
- 0.01
h5
LF
DC
DCON(h5)
DC
SQUARE
30
15
DN
UWC
DCON(h5)
CARBIDE
LF
4 < DCON < 6 8<DCON<10 DCON=12

0
- 0.005
0
- 0.006
0
- 0.008
a 2 flute ball nose end mill with Impact Miracle coating for high hardened materials.
J228
Order Number
PRFRAD
DC
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VF2SSBR0050S04
VF2SSBR0050
VF2SSBR0075S04
VF2SSBR0075
VF2SSBR0100
VF2SSBR0150
VF2SSBR0200
VF2SSBR0250
VF2SSBR0300
VF2SSBR0400
VF2SSBR0500
VF2SSBR0600
0.5
0.5
0.75
0.75
1
1.5
2
2.5
3
4
5
6
1
1
1.5
1.5
2
3
4
5
6
8
10
12
1
1
1.5
1.5
2
3
4
5
6
8
10
12
2
2
3
3
4
6
8
10
12
14
18
22
0.94
0.94
1.44
1.44
1.9
2.9
3.9
4.9
5.85
7.85
9.7
11.7
40
40
40
40
45
45
45
50
50
60
70
75
4
6
4
6
6
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
2
2
2
2
0.010
DC < 12
DC>12
h6
DCON=3 4 < DCON < 6 8<DCON<10

0
- 0.004
0
- 0.005
PRFRAD
0
- 0.006
DCON=12 DCON=16 DCON=20

0
- 0.008
0
- 0.011
APMX
LU
DN
LF
10
20
APMX
LU
LF
15
APMX
LU
LF
0
- 0.013
PRFRAD
APMX
DCON>12
a 2 flute ball nose end mill with Impact Miracle coating for high hardened materials.
LF
Type1
Type2
Type3
Type4
Order Number
PRFRAD
DC
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
Unit : mm
VF2SBR0010S04
VF2SBR0010S06
VF2SBR0015S04
VF2SBR0015S06
VF2SBR0020S04
VF2SBR0020S06
VF2SBR0030S04
VF2SBR0030S06
VF2SBR0040S04
VF2SBR0040S06
VF2SBR0050S04
VF2SBR0050S06
VF2SBR0060S04
VF2SBR0060S06
VF2SBR0070S04
VF2SBR0070S06
VF2SBR0075S04
VF2SBR0075S06
VF2SBR0080S04
VF2SBR0080S06
VF2SBR0090S04
VF2SBR0090S06
VF2SBR0100S04
VF2SBR0100S06
VF2SBR0125S06
VF2SBR0150S03
VF2SBR0150S06
VF2SBR0200S04
VF2SBR0200S06
VF2SBR0250S06
VF2SBR0300S06
VF2SBR0400S08
VF2SBR0500S10
VF2SBR0600S12
0.1
0.1
0.15
0.15
0.2
0.2
0.3
0.3
0.4
0.4
0.5
0.5
0.6
0.6
0.7
0.7
0.75
0.75
0.8
0.8
0.9
0.9
1
1
1.25
1.5
1.5
2
2
2.5
3
4
5
6
0.2
0.2
0.3
0.3
0.4
0.4
0.6
0.6
0.8
0.8
1
1
1.2
1.2
1.4
1.4
1.5
1.5
1.6
1.6
1.8
1.8
2
2
2.5
3
3
4
4
5
6
8
10
12
0.2
0.2
0.3
0.3
0.4
0.4
0.6
0.6
0.8
0.8
1
1
1.2
1.2
1.4
1.4
1.5
1.5
1.6
1.6
1.8
1.8
2
2
2.5
3
3
4
4
5
12
14
18
22
0.4
0.4
0.6
0.6
0.8
0.8
1.2
1.2
1.6
1.6
2
2
2.4
2.4
2.8
2.8
3
3
3.2
3.2
3.6
3.6
4
4
5
8
10
0.17
0.17
0.27
0.27
0.36
0.36
0.56
0.56
0.76
0.76
0.94
0.94
1.14
1.14
1.34
1.34
1.44
1.44
1.54
1.54
1.74
1.74
1.9
1.9
2.4
2.9
3.9
4.9
45
50
45
50
45
50
45
50
45
50
45
50
45
50
45
50
45
50
45
50
45
50
50
60
60
60
70
60
70
80
80
90
100
110
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
6
3
6
4
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
2
1
2
1
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
3
4
3
3
4
4
4
4
SQUARE
10
DC
h5
DCON < 12
0
- 0.02
DC
0
- 0.01
PRFRAD
Aluminium Alloy
BALL
0.005
DC
PRFRAD<6 PRFRAD>6
Copper Alloy
RADIUS
TAPER
SOLID END MILLS
DCON(h5)
DCON(h5)
Titanium Alloy,
PRFRAD
CARBIDE
DCON(h5)
Austenitic
Stainless Steel
DN
Hardened Steel
(>55HRC)
30
PRFRAD<0.3 PRFRAD>0.3 PRFRAD<0.3 PRFRAD>0.3
Hardened Steel
( < 55HRC)
DC
VF
DN
(<30HRC)
( < 45HRC)
UWC
DCON(h5/h6)
VF2SB
J229
VF2SB
PRFRAD
DC
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
VF2SBR0800S16
VF2SBR1000S20
8
10
16
20
30
38
140
160
16
20
2
2
RADIUS
TAPER
SOLID END MILLS
J230
Unit : mm
Order Number
BALL
SQUARE
CARBIDE
Type
4
4
VF2SSB
VF2SB
CARBIDE

Work
material
AISI H13
AISI D2
AISI W1, AISI M2
%< 15
%>15
%< 15
%>15
%< 15
%>15
R
Depth of cut
Depth of cut
Depth of cut
PRFRAD Revolution Feed rate Revolution Feed rate
Feed rate Revolution Feed rate ap(mm) Revolution Feed rate Revolution Feed rate ap(mm)
ap(mm) Revolution
-1
-1
-1
-1
-1
-1
(mm)
(min ) (mm/min) (min ) (mm/min)
R 0.1
R 0.15
R 0.2
R 0.3
R 0.4
R 0.5
R 0.75
R 1
R 1.25
R 1.5
R 2
R 2.5
R 3
R 4
R 5
R 6
R 8
R10
40000
320 40000
40000
640 40000
40000 1600 40000
40000 3200 40000
40000 6400 40000
40000 8000 40000
40000 9600 40000
40000 9600 39000
40000 10400 32000
40000 12000 27000
32000 10880 20000
25000 9000 16000
21000 8400 13000
16000 6400 10000
13000 5200 8000
9000 3600 6000
6000 2400 4000
4500 1800 3000
240
560
1200
1600
2400
3200
4000
4700
4500
4300
3600
2900
2600
2000
1700
1300
1000
780
0.003
0.01
0.02
0.03
0.05
0.06
0.09
0.11
0.12
0.13
0.15
0.2
0.25
0.3
0.5
0.5
0.5
0.5
40000
40000
40000
40000
40000
40000
40000
40000
37000
32000
24000
19000
16000
12000
10000
7000
5000
4000
320
640
1400
2800
4000
5600
7200
8000
8100
7700
6200
5300
4800
3600
3200
2200
1600
1300
40000
40000
40000
40000
40000
40000
32000
24000
19000
16000
12000
9600
8000
6000
4800
3600
2500
1800
160
400
1000
1200
1600
2400
2500
2400
2300
2200
1900
1700
1600
1200
960
720
500
360
0.003
0.007
0.015
0.025
0.04
0.05
0.075
0.1
0.11
0.12
0.13
0.15
0.2
0.2
0.2
0.3
0.3
0.3
40000
40000
40000
40000
40000
40000
32000
24000
19000
16000
12000
9600
8000
6000
4800
3600
2500
1800
320
640
1200
2000
2800
3600
4500
3800
3400
3200
2400
2100
1700
1400
1100
860
650
470
40000
40000
40000
40000
40000
32000
21000
16000
13000
11000
8000
6000
5000
4000
3000
2200
1500
1000
160
400
1000
1200
1600
1300
1200
1000
1000
880
800
600
600
480
420
310
240
160
0.002
0.005
0.01
0.02
0.03
0.04
0.05
0.07
0.08
0.09
0.1
0.1
0.11
0.11
0.12
0.12
0.15
0.15
< Please
PRFRAD:Radius

SOLID END MILLS
< 0.2PRFRAD
Depth of
cut
End mill
ap
PRFRAD
pf
J231
IMPACT MIRACLE BALL NOSE HIGH POWER END MILL
VF2SDB
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Titanium Alloy,
Austenitic
Stainless Steel
VF
Copper Alloy
30
Aluminium Alloy
15
DC
SQUARE
DN
Hardened Steel
( < 55HRC)
UWC
h6
Type2
0.01
0.02
DC < 12
DC>12
PRFRAD
0
- 0.02
LF
DN
PRFRAD<6.5 PRFRAD>6.5
DC
BALL
APMX
LU
DCON(h6)
Type1
PRFRAD
0
- 0.03
APMX
LU
DCON(h6)
CARBIDE
LF
DCON=3 4 < DCON < 6 8<DCON<10 12<DCON<16 DCON=20

0
- 0.006
0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
hardness materials and achieves excellent fracture resistance.
J232
Order Number
PRFRAD
DC
APMX
LU
DN
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
a 2 flute ball nose end mill with Impact Miracle coating for high
VF2SDBR0050
VF2SDBR0100S04
VF2SDBR0100
VF2SDBR0150S03
VF2SDBR0150
VF2SDBR0200S04
VF2SDBR0200
VF2SDBR0250
VF2SDBR0300
VF2SDBR0400
VF2SDBR0500
VF2SDBR0600
VF2SDBR0800
VF2SDBR1000
0.5
1
1
1.5
1.5
2
2
2.5
3
4
5
6
8
10
1
2
2
3
3
4
4
5
6
8
10
12
16
20
1
2
2
3
3
4
4
5
12
14
18
22
30
38
2
4
4
6
6
8
8
10
22
27
31
35
50
58
0.94
1.9
1.9
2.9
2.9
3.9
3.9
4.9
5.85
7.85
9.7
11.7
15.5
19.5
45
50
60
60
70
60
70
80
80
90
100
110
140
160
4
4
6
3
6
4
6
6
6
8
10
12
16
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
2
1
2
1
1
2
2
2
2
2
2
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Titanium Alloy,
Austenitic
Stainless Steel
VF
Copper Alloy
30
CARBIDE
Aluminium Alloy
10
DC
DN
Hardened Steel
( < 55HRC)
UWC
PRFRAD
h6
PRFRAD
0
- 0.03
APMX
LU
LF

0
- 0.008
0
- 0.009
0
- 0.011
BALL
0.02
DC>12
DCON(h6)
Type2
0.01
DC < 12
0
- 0.02
LF
DN
DC
APMX
LU
DCON(h6)
Type1
SQUARE
VF2SDBL
0
- 0.013
DC
APMX
LU
DN
LF
DCON
Stock
VF2SDBLR0050
VF2SDBLR0100
VF2SDBLR0150
VF2SDBLR0200
VF2SDBLR0250
VF2SDBLR0300
VF2SDBLR0400
VF2SDBLR0500
VF2SDBLR0600
VF2SDBLR0800
VF2SDBLR1000
0.5
1
1.5
2
2.5
3
4
5
6
8
10
1
2
3
4
5
6
8
10
12
16
20
1
2
3
4
5
12
14
18
22
30
38
2
4
6
8
10
22
27
31
35
50
58
0.94
1.9
2.9
3.9
4.9
5.85
7.85
9.7
11.7
15.5
19.5
60
80
90
90
110
120
130
140
140
200
200
6
6
6
6
8
6
8
10
12
16
20
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
2
2
2
2
2
2
TAPER
PRFRAD
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute end mill with long shank for general use.
J233
IMPACT MIRACLE BALL NOSE HIGH POWER END MILL

CARBIDE
VF2SDB
VF2SDBL

y Overhang below 5D (D:Dia.)
Work
material

Pre-hardened steel
AISI H13
AISI D2
%< 15
%>15
%< 15
%>15
%< 15
%>15
R
ae
ap
ae
ap
ae
ap
(mm)
R 0.5
R 1
R 1.5x3
R 1.5
R 2x4
R 2
R 2.5
R 3
R 4
R 5
R 6
R 8
R10
40000
40000
29000
37000
24000
30000
25000
22000
19000
15000
12000
9000
7500
5200
6000
4600
7000
4300
6500
6000
6000
5200
4300
3400
2600
2200
36000
36000
19000
24000
15000
19000
16000
14000
12000
9500
8000
6000
4800
2300
3500
2400
3000
2200
2800
2600
2400
2200
2000
1800
1500
1200
0.10
0.20
0.20
0.30
0.25
0.40
0.50
0.60
0.80
1.00
1.20
1.60
2.00
0.25
0.50
0.50
0.75
0.70
1.00
1.30
1.80
2.40
3.00
3.60
4.80
6.00
40000
40000
25000
37000
19000
28000
22000
18000
15000
11000
9000
7000
5500
5200
6000
4000
7000
3400
6000
5000
4500
3800
3000
2400
1900
1500
36000
36000
16000
24000
13000
19000
16000
12000
9500
7000
6000
4500
3600
2300
3500
2000
3000
1700
2600
2300
1900
1700
1500
1400
1100
900
0.10
0.20
0.20
0.30
0.25
0.40
0.50
0.60
0.80
1.00
1.20
1.60
2.00
0.25
0.50
0.50
0.75
0.70
1.00
1.25
1.50
2.00
2.50
3.00
4.00
5.00
40000
36000
17000
25000
12000
18000
15000
12000
9800
7500
6000
4500
3600
5000
5000
2400
6000
1900
4800
4200
3500
3000
2400
1900
1500
1200
40000
24000
11000
16000
8200
12000
9500
8000
6500
5000
4000
3000
2500
2400
2400
1000
2200
900
2000
1700
1600
1300
1000
800
600
500
0.05
0.10
0.12
0.12
0.13
0.13
0.15
0.20
0.20
0.20
0.30
0.30
0.30
0.10
0.20
0.30
0.30
0.40
0.40
0.50
0.60
0.80
1.00
1.20
1.60
2.00
ae
SOLID END MILLS
Depth of
cut
< ap

End mill
pf
J234
ap
PRFRAD
CARBIDE
y Overhang 7D (D:Dia.)
Work
material

Pre-hardened steel
AISI H13
R
Revolution
(min-1)
PRFRAD (mm)
R 1.5x3
R 2x4
R 3
R 4
R 5
R 6
R 8
R10
16000
13000
10000
8000
6000
5000
3800
3000
Feed rate Depth of cut Depth of cut Revolution

(mm/min)
ap (mm)
ae (mm)
(min-1)
2000
2000
2000
1800
1600
1300
1000
800
0.10
0.15
0.20
0.30
0.40
0.45
0.60
0.80
0.30
0.50
1.00
1.50
2.00
2.40
3.00
4.00
13000
10000
8000
6400
4800
4000
3100
2500
Feed rate Depth of cut Depth of cut

ap (mm)
ae (mm)
(mm/min)
1500
1500
1600
1400
1200
1000
800
650
0.10
0.15
0.20
0.40
0.40
0.45
0.60
0.80
0.30
0.50
0.80
1.20
1.60
2.00
2.50
3.00
ae
Depth of
cut
ap
SOLID END MILLS
J235
VF2XLBS
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Aluminium Alloy
B2
Type1
DC
SQUARE
BALL
DCON(h6)
15
APMX
LF
0.2<PRFRAD<1
0.007
Inclined angle
0.4 < DC < 2

0
- 0.02
DCON=4
0
- 0.008
a 2 flute long neck ball nose end mill for high-speed machining of hardened steel.
a Short shank type suitable for use with a shrink fit holder.
PRFRAD
DC
APMX
LU
DN
B2
LF
DCON
VF2XLBSR0020N010
VF2XLBSR0020N020
VF2XLBSR0020N030
VF2XLBSR0020N040
VF2XLBSR0025N040
VF2XLBSR0025N060
VF2XLBSR0030N020
VF2XLBSR0030N030
VF2XLBSR0030N040
VF2XLBSR0030N060
VF2XLBSR0040N040
VF2XLBSR0040N060
VF2XLBSR0050N030
VF2XLBSR0050N040
VF2XLBSR0050N060
VF2XLBSR0050N080
VF2XLBSR0100N060
VF2XLBSR0100N080
VF2XLBSR0100N100
0.2
0.2
0.2
0.2
0.25
0.25
0.3
0.3
0.3
0.3
0.4
0.4
0.5
0.5
0.5
0.5
1
1
1
0.4
0.4
0.4
0.4
0.5
0.5
0.6
0.6
0.6
0.6
0.8
0.8
1
1
1
1
2
2
2
0.32
0.32
0.32
0.32
0.4
0.4
0.48
0.48
0.48
0.48
0.64
0.64
0.8
0.8
0.8
0.8
1.6
1.6
1.6
1
2
3
4
4
6
2
3
4
6
4
6
3
4
6
8
6
8
10
0.36
0.36
0.36
0.36
0.46
0.46
0.56
0.56
0.56
0.56
0.76
0.76
0.94
0.94
0.94
0.94
1.9
1.9
1.9
13.4
11.9
10.7
9.7
9.6
8.1
11.8
10.5
9.5
8.0
9.4
7.8
10.1
9.1
7.5
6.4
6.4
5.3
4.5
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
Order Number
Stock
Unit : mm
No. of Flutes
RADIUS
TAPER
Copper Alloy
LU
Effective length
for inclined angle
h6
SOLID END MILLS
30
PRFRAD
J236
Titanium Alloy,
Austenitic
Stainless Steel
DN
Hardened Steel
( < 55HRC)
VF
UWC
Effective
length
CARBIDE
Effective length
for inclined angle
30'
1 1.0
1 2.0
1 3.1
1 4.1
1 4.1
1 6.2
1 2.1
1 3.1
1 4.2
1 6.3
1 4.2
1 6.3
1 3.2
1 4.2
1 6.3
1 8.4
1 6.2
1 8.3
1 10.4
1.0
2.1
3.2
4.3
4.3
6.4
2.2
3.3
4.3
6.5
4.3
6.5
3.3
4.4
6.6
8.8
6.5
8.7
10.8
1.1
2.3
3.4
4.6
4.6
6.9
2.3
3.5
4.6
6.9
4.6
6.9
3.6
4.8
7.1
9.4
6.9
9.2
11.5
1.2
2.5
3.7
4.9
4.9
7.4
2.5
3.8
5.0
7.5
5.0
7.5
3.9
5.2
7.7
10.2
7.4
9.9
12.4
VF2XLB
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
u
DN
Hardened Steel
( < 55HRC)
30
B2
DC
Type1
0.010
PRFRAD
Inclined angle
0.2 < DC < 6
DCON(h6)
Type2
APMX
LU
LF
0
- 0.02
h6
BALL
0.007
DCON(h6)
Effective
length
PRFRAD<1 PRFRAD>1
LF
DC
APMX
LU
DN
PRFRAD
Effective length
for inclined angle
12
SQUARE
(<30HRC)
( < 45HRC)
VF
UWC
4 < DCON < 6

0
- 0.008
LU
DN
B2
LF
DCON
VF2XLBR0010N005S04
VF2XLBR0010N005S06
VF2XLBR0010N008S04
VF2XLBR0010N010S04
VF2XLBR0010N010S06
VF2XLBR0010N013S04
VF2XLBR0010N015S04
VF2XLBR0010N015S06
VF2XLBR0010N018S04
VF2XLBR0010N020S04
VF2XLBR0010N025S04
VF2XLBR0015N010S04
VF2XLBR0015N010S06
VF2XLBR0015N013S04
VF2XLBR0015N015S04
VF2XLBR0015N015S06
VF2XLBR0015N018S04
VF2XLBR0015N020S04
VF2XLBR0015N020S06
VF2XLBR0015N025S04
VF2XLBR0015N030S04
VF2XLBR0015N040S04
VF2XLBR0020N010S04
VF2XLBR0020N010S06
VF2XLBR0020N015S04
VF2XLBR0020N015S06
VF2XLBR0020N020S04
VF2XLBR0020N020S06
VF2XLBR0020N025S04
VF2XLBR0020N025S06
VF2XLBR0020N030S04
VF2XLBR0020N030S06
VF2XLBR0020N040S04
VF2XLBR0020N050S04
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.32
0.32
0.32
0.32
0.32
0.32
0.32
0.32
0.32
0.32
0.32
0.32
0.5
0.5
0.75
1
1
1.25
1.5
1.5
1.75
2
2.5
1
1
1.25
1.5
1.5
1.75
2
2
2.5
3
4
1
1
1.5
1.5
2
2
2.5
2.5
3
3
4
5
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.27
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
11.5
11.7
11.2
10.9
11.3
10.7
10.4
10.9
10.2
10
9.5
11
11.3
10.7
10.4
10.9
10.2
9.9
10.6
9.5
9.1
8.4
11
11.3
10.4
11
10
10.6
9.5
10.3
9.1
10
8.4
7.8
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
6
4
4
6
4
4
6
4
4
4
4
6
4
4
6
4
4
6
4
4
4
4
6
4
6
4
6
4
6
4
6
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
0.5
0.5
0.7
1.0
1.0
1.3
1.5
1.5
1.8
2.1
2.6
1.0
1.0
1.3
1.5
1.5
1.8
2.1
2.1
2.6
3.1
4.2
1.0
1.0
1.5
1.5
2.0
2.0
2.6
2.6
3.1
3.1
4.1
5.2
0.5
0.5
0.8
1.1
1.1
1.3
1.6
1.6
1.9
2.2
2.7
1.1
1.1
1.3
1.6
1.6
1.9
2.2
2.2
2.7
3.2
4.3
1.0
1.0
1.6
1.6
2.1
2.1
2.7
2.7
3.2
3.2
4.3
5.4
0.6
0.6
0.9
1.2
1.2
1.5
1.8
1.8
2.1
2.4
3.0
1.2
1.2
1.5
1.8
1.8
2.1
2.4
2.4
3.0
3.6
4.8
1.1
1.1
1.7
1.7
2.3
2.3
2.9
2.9
3.5
3.5
4.7
5.9
0.6
0.6
1.0
1.3
1.3
1.6
2.0
2.0
2.3
2.6
3.3
1.3
1.3
1.6
1.9
1.9
2.3
2.6
2.6
3.3
3.9
5.3
1.2
1.2
1.9
1.9
2.6
2.6
3.2
3.2
3.9
3.9
5.2
6.6
TAPER
APMX
SOLID END MILLS
DC
Type
PRFRAD
Stock
Order Number
No. of Flutes
Unit : mm
RADIUS
a 2 flute long neck ball nose end mill with Impact Miracle coating for high hardened materials.
J237
VF2XLB
DC
APMX
VF2XLBR0025N015S04
VF2XLBR0025N015S06
VF2XLBR0025N020S04
VF2XLBR0025N020S06
VF2XLBR0025N025S04
VF2XLBR0025N030S04
VF2XLBR0025N030S06
VF2XLBR0025N035S04
VF2XLBR0025N040S04
VF2XLBR0025N040S06
VF2XLBR0025N050S04
VF2XLBR0025N050S06
VF2XLBR0025N060S04
VF2XLBR0025N060S06
VF2XLBR0030N020S04
VF2XLBR0030N020S06
VF2XLBR0030N025S04
VF2XLBR0030N030S04
VF2XLBR0030N030S06
VF2XLBR0030N035S04
VF2XLBR0030N040S04
VF2XLBR0030N040S06
VF2XLBR0030N050S04
VF2XLBR0030N050S06
VF2XLBR0030N060S04
VF2XLBR0030N060S06
VF2XLBR0030N070S04
VF2XLBR0030N080S04
VF2XLBR0030N080S06
VF2XLBR0040N020S04
VF2XLBR0040N020S06
VF2XLBR0040N030S04
VF2XLBR0040N030S06
VF2XLBR0040N040S04
VF2XLBR0040N040S06
VF2XLBR0040N050S04
VF2XLBR0040N060S04
VF2XLBR0040N060S06
VF2XLBR0040N070S04
VF2XLBR0040N080S04
VF2XLBR0040N080S06
VF2XLBR0040N100S04
VF2XLBR0040N100S06
VF2XLBR0050N030S04
VF2XLBR0050N030S06
VF2XLBR0050N040S04
VF2XLBR0050N040S06
VF2XLBR0050N050S04
VF2XLBR0050N050S06
VF2XLBR0050N060S04
VF2XLBR0050N060S06
VF2XLBR0050N070S04
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.48
0.48
0.48
0.48
0.48
0.48
0.48
0.48
0.48
0.48
0.48
0.48
0.48
0.48
0.48
0.64
0.64
0.64
0.64
0.64
0.64
0.64
0.64
0.64
0.64
0.64
0.64
0.64
0.64
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
J238
LU
DN
B2
LF
DCON
1.5
1.5
2
2
2.5
3
3
3.5
4
4
5
5
6
6
2
2
2.5
3
3
3.5
4
4
5
5
6
6
7
8
8
2
2
3
3
4
4
5
6
6
7
8
8
10
10
3
3
4
4
5
5
6
6
7
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
10.5
11
10
10.6
9.5
9.1
10
8.7
8.3
9.4
7.7
8.9
7.2
8.4
9.9
10.6
9.4
9
9.9
8.6
8.3
9.3
7.6
8.8
7.1
8.4
6.6
6.2
7.6
9.9
10.6
8.9
9.9
8.2
9.3
7.5
7
8.3
6.5
6.1
7.5
5.4
6.8
8.8
9.8
8
9.2
7.3
8.7
6.8
8.2
6.3
50
50
50
50
50
50
50
50
50
50
50
50
50
60
50
50
50
50
50
50
50
50
50
50
50
50
50
50
60
50
50
50
50
50
50
50
50
50
50
50
50
50
60
50
50
50
50
50
50
50
50
50
4
6
4
6
4
4
6
4
4
6
4
6
4
6
4
6
4
4
6
4
4
6
4
6
4
6
4
4
6
4
6
4
6
4
6
4
4
6
4
4
6
4
6
4
6
4
6
4
6
4
6
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
PRFRAD
Stock
Order Number
Unit : mm
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
Effective length
for inclined angle
30'
1 1.5 1.6 1.7 1.9

1 1.5 1.6 1.7 1.9
1 2.0 2.1 2.3 2.6
1 2.0 2.1 2.3 2.6
1 2.6 2.7 2.9 3.2
1 3.1 3.2 3.5 3.9
1 3.1 3.2 3.5 3.9
1 3.6 3.8 4.1 4.5
1 4.1 4.3 4.7 5.2
1 4.1 4.3 4.7 5.2
1 5.2 5.4 5.9 6.5
1 5.2 5.4 5.9 6.5
1 6.2 6.5 7.1 7.9
1 6.2 6.5 7.1 7.9
1 2.1 2.2 2.4 2.6
1 2.1 2.2 2.4 2.6
1 2.6 2.7 3.0 3.3
1 3.1 3.3 3.6 3.9
1 3.1 3.3 3.6 3.9
1 3.6 3.8 4.2 4.6
1 4.2 4.4 4.8 5.2
1 4.2 4.4 4.8 5.2
1 5.2 5.4 6.0 6.6
1 5.2 5.4 6.0 6.6
1 6.3 6.5 7.1 7.9
1 6.3 6.5 7.1 7.9
1 7.3 7.6 8.3 9.2
1 8.3 8.7 9.5 10.6
1 8.3 8.7 9.5 10.6
1 2.1 2.2 2.3 2.6
1 2.1 2.2 2.3 2.6
1 3.1 3.3 3.5 3.9
1 3.1 3.3 3.5 3.9
1 4.2 4.3 4.7 5.2
1 4.2 4.3 4.7 5.2
1 5.2 5.4 5.9 6.5
1 6.3 6.5 7.1 7.9
1 6.3 6.5 7.1 7.9
1 7.3 7.6 8.3 9.2
1 8.3 8.7 9.5 10.5
1 8.3 8.7 9.5 10.5
1 10.4 10.9 11.9 13.2
1 10.4 10.9 11.9 13.2
1 3.2 3.3 3.6 4.0
1 3.2 3.3 3.6 4.0
1 4.2 4.4 4.8 5.3
1 4.2 4.4 4.8 5.3
1 5.3 5.5 6.0 6.7
1 5.3 5.5 6.0 6.7
1 6.3 6.6 7.2 8.0
1 6.3 6.6 7.2 8.0
1 7.4 7.7 8.4 9.3
CARBIDE
LF
DCON
VF2XLBR0050N080S04
VF2XLBR0050N080S06
VF2XLBR0050N090S04
VF2XLBR0050N100S04
VF2XLBR0050N100S06
VF2XLBR0050N120S04
VF2XLBR0050N120S06
VF2XLBR0050N140S04
VF2XLBR0050N160S04
VF2XLBR0050N160S06
VF2XLBR0050N180S04
VF2XLBR0050N200S04
VF2XLBR0050N200S06
VF2XLBR0060N060S04
VF2XLBR0060N060S06
VF2XLBR0060N080S04
VF2XLBR0060N080S06
VF2XLBR0060N100S04
VF2XLBR0060N100S06
VF2XLBR0060N120S04
VF2XLBR0060N120S06
VF2XLBR0060N140S04
VF2XLBR0060N160S04
VF2XLBR0060N160S06
VF2XLBR0070N080S04
VF2XLBR0070N120S04
VF2XLBR0070N160S04
VF2XLBR0075N060S04
VF2XLBR0075N060S06
VF2XLBR0075N080S04
VF2XLBR0075N080S06
VF2XLBR0075N100S04
VF2XLBR0075N100S06
VF2XLBR0075N120S04
VF2XLBR0075N120S06
VF2XLBR0075N140S04
VF2XLBR0075N140S06
VF2XLBR0075N160S04
VF2XLBR0075N160S06
VF2XLBR0075N180S04
VF2XLBR0075N200S04
VF2XLBR0075N200S06
VF2XLBR0080N080S04
VF2XLBR0080N120S04
VF2XLBR0080N160S04
VF2XLBR0080N200S04
VF2XLBR0090N080S04
VF2XLBR0090N120S04
VF2XLBR0090N160S04
VF2XLBR0090N200S04
VF2XLBR0100N060S04
VF2XLBR0100N060S06
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.8
0.8
0.8
0.8
0.9
0.9
0.9
0.9
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
2
2
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
0.96
1.12
1.12
1.12
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.28
1.28
1.28
1.28
1.44
1.44
1.44
1.44
1.6
1.6
8
8
9
10
10
12
12
14
16
16
18
20
20
6
6
8
8
10
10
12
12
14
16
16
8
12
16
6
6
8
8
10
10
12
12
14
14
16
16
18
20
20
8
12
16
20
8
12
16
20
6
6
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.14
1.14
1.14
1.14
1.14
1.14
1.14
1.14
1.14
1.14
1.14
1.34
1.34
1.34
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.54
1.54
1.54
1.54
1.74
1.74
1.74
1.74
1.9
1.9
5.9
7.4
5.5
5.2
6.7
4.6
6.1
4.2
3.8
5.3
3.5
3.3
4.6
6.6
8.1
5.7
7.3
5
6.6
4.5
6
4
3.7
5.2
5.5
4.3
3.5
6.3
8
5.4
7.2
4.7
6.5
4.2
5.9
3.8
5.4
3.4
5
3.1
2.9
4.3
5.3
4.1
3.3
2.8
5.1
3.9
3.1
2.6
5.8
7.9
50
50
50
50
50
50
60
60
60
70
60
60
70
50
50
50
50
50
50
50
50
60
60
70
50
50
60
50
50
50
50
50
50
50
50
50
50
60
60
60
60
70
50
50
60
60
50
50
60
60
50
50
4
6
4
4
6
4
6
4
4
6
4
4
6
4
6
4
6
4
6
4
6
4
4
6
4
4
4
4
6
4
6
4
6
4
6
4
6
4
6
4
4
6
4
4
4
4
4
4
4
4
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
8.4
8.4
9.5
10.5
10.5
12.6
12.6
14.7
16.8
16.8
18.9
21.0
21.0
6.3
6.3
8.4
8.4
10.5
10.5
12.6
12.6
14.7
16.8
16.8
8.4
12.6
16.8
6.3
6.3
8.4
8.4
10.5
10.5
12.6
12.6
14.7
14.7
16.8
16.8
18.9
21.0
21.0
8.4
12.6
16.8
21.0
8.4
12.6
16.8
20.9
6.2
6.2
8.8
8.8
9.9
11.0
11.0
13.2
13.2
15.3
17.5
17.5
19.7
21.9
21.9
6.6
6.6
8.8
8.8
11.0
11.0
13.2
13.2
15.3
17.5
17.5
8.8
13.1
17.5
6.6
6.6
8.8
8.8
11.0
11.0
13.1
13.1
15.3
15.3
17.5
17.5
19.7
21.9
21.9
8.8
13.1
17.5
21.9
8.8
13.1
17.5
21.8
6.5
6.5
9.6
9.6
10.8
12.0
12.0
14.4
14.4
16.8
19.2
19.2
21.6
24.0
24.0
7.2
7.2
9.6
9.6
12.0
12.0
14.4
14.4
16.8
19.2
19.2
9.6
14.4
19.2
7.2
7.2
9.6
9.6
12.0
12.0
14.4
14.4
16.8
16.8
19.2
19.2
21.6
23.9
23.9
9.6
14.4
19.1
23.9
9.6
14.3
19.1
23.9
7.0
7.0
10.6
10.6
12.0
13.3
13.3
15.9
15.9
18.6
21.3
21.3
23.9
26.6
26.6
8.0
8.0
10.6
10.6
13.3
13.3
15.9
15.9
18.6
21.2
21.2
10.6
15.9
21.2
7.9
7.9
10.6
10.6
13.2
13.2
15.9
15.9
18.5
18.5
21.2
21.2
23.8
SQUARE
B2
BALL
DN
RADIUS
LU
TAPER
APMX
SOLID END MILLS
DC
Type
PRFRAD
Stock
Order Number
No. of Flutes
Unit : mm
26.5
10.5
15.9
21.2
10.5
15.8
21.1
7.7
7.7
* No interference
J239
VF2XLB
PRFRAD
DC
APMX
LU
DN
B2
LF
DCON
VF2XLBR0100N080S04
VF2XLBR0100N080S06
VF2XLBR0100N100S04
VF2XLBR0100N100S06
VF2XLBR0100N120S04
VF2XLBR0100N120S06
VF2XLBR0100N140S04
VF2XLBR0100N140S06
VF2XLBR0100N160S04
VF2XLBR0100N160S06
VF2XLBR0100N180S04
VF2XLBR0100N180S06
VF2XLBR0100N200S04
VF2XLBR0100N200S06
VF2XLBR0100N220S04
VF2XLBR0100N250S04
VF2XLBR0100N250S06
VF2XLBR0100N300S04
VF2XLBR0100N300S06
VF2XLBR0100N350S04
VF2XLBR0125N100S06
VF2XLBR0125N150S06
VF2XLBR0125N200S06
VF2XLBR0125N250S06
VF2XLBR0125N300S06
VF2XLBR0125N350S06
VF2XLBR0150N080S06
VF2XLBR0150N100S06
VF2XLBR0150N120S06
VF2XLBR0150N140S06
VF2XLBR0150N160S06
VF2XLBR0150N200S06
VF2XLBR0150N250S06
VF2XLBR0150N300S06
VF2XLBR0150N350S06
VF2XLBR0150N400S06
VF2XLBR0175N160S06
VF2XLBR0175N200S06
VF2XLBR0175N250S06
VF2XLBR0175N300S06
VF2XLBR0175N350S06
VF2XLBR0175N400S06
VF2XLBR0200N100S06
VF2XLBR0200N120S06
VF2XLBR0200N140S06
VF2XLBR0200N160S06
VF2XLBR0200N200S06
VF2XLBR0200N250S06
VF2XLBR0200N300S06
VF2XLBR0200N350S06
VF2XLBR0200N400S06
VF2XLBR0200N450S06
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.25
1.25
1.25
1.25
1.25
1.25
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.75
1.75
1.75
1.75
1.75
1.75
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
3.5
3.5
3.5
3.5
3.5
3.5
4
4
4
4
4
4
4
4
4
4
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
2
2
2
2
2
2
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.8
2.8
2.8
2.8
2.8
2.8
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
8
8
10
10
12
12
14
14
16
16
18
18
20
20
22
25
25
30
30
35
10
15
20
25
30
35
8
10
12
14
16
20
25
30
35
40
16
20
25
30
35
40
10
12
14
16
20
25
30
35
40
45
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.4
2.4
2.4
2.4
2.4
2.4
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
3.4
3.4
3.4
3.4
3.4
3.4
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
4.9
6.9
4.2
6.2
3.7
5.6
3.3
5.1
2.9
4.7
2.7
4.4
2.5
4.1
2.3
2
3.5
1.7
3
1.5
5.9
4.6
3.7
3.2
2.8
2.4
6.3
5.5
4.9
4.4
4
3.4
2.8
2.5
2.2
1.9
3.6
3
2.5
2.1
1.9
1.7
4.5
3.9
3.4
3.1
2.6
2.1
1.8
1.6
1.4
1.2
50
50
50
50
50
50
50
50
60
60
60
60
60
60
60
70
70
70
80
80
60
60
70
70
80
80
60
60
60
60
60
70
70
70
80
90
60
70
70
80
80
90
70
70
70
70
70
70
70
80
90
90
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
4
6
4
6
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Type
Order Number
Stock
Unit : mm
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
8.3
8.3
10.4
10.4
12.5
12.5
14.6
14.6
16.7
16.7
18.8
18.8
20.9
20.9
22.9
26.1
26.1
31.3
31.3
36.5
10.4
15.6
20.8
26.1
31.3
36.5
8.3
10.4
12.5
14.6
16.7
20.8
26.1
31.3
36.5
41.7
16.7
20.8
26.0
31.3
36.5
41.7
10.4
12.5
14.6
16.6
20.8
26.0
31.2
36.5
41.7
46.9
8.7
8.7
10.9
10.9
13.0
13.0
15.2
15.2
17.4
17.4
19.6
19.6
21.8
21.8
23.9
27.2
27.2
32.6
32.6
38.1
10.8
16.3
21.7
27.2
32.6
38.1
8.6
10.8
13.0
15.2
17.3
21.7
27.2
32.6
38.0
43.5
17.3
21.7
27.1
32.6
38.0
43.5
10.8
12.9
15.1
17.3
21.7
27.1
32.6
38.0
43.5
48.9
9.4
9.4
11.8
11.8
14.2
14.2
16.6
16.6
19.0
19.0
21.4
21.4
23.8
23.8
26.2
10.4
10.4
13.0
13.0
15.7
15.7
18.3
18.3
*
a
J240
21.0
23.6
26.3
*
*
*
29.8 32.9
*
*
*
*
*
11.8 12.9
35.8
17.8
23.8
29.7
35.7
41.7
9.3
11.7
14.1
16.5
18.9
23.7
29.7
35.7
41.7
19.6
26.2
32.9
*
*
10.2
12.9
15.5
18.2
20.8
26.1
*
*
*
*
*
18.9 20.8
*
*
*
* *
* *
11.6 12.7
23.7
29.6
35.6
14.0 15.4
16.4 18.0
18.8 20.7
23.6
29.6
*
*
* *
* *
* *
* *
No interference
CARBIDE
LF
DCON
VF2XLBR0200N500S06
VF2XLBR0250N200S06
VF2XLBR0250N250S06
VF2XLBR0250N300S06
VF2XLBR0250N350S06
VF2XLBR0300N300S06
VF2XLBR0300N400S06
VF2XLBR0300N500S06
2
2.5
2.5
2.5
2.5
3
3
3
4
5
5
5
5
6
6
6
3.2
4
4
4
4
4.8
4.8
4.8
50
20
25
30
35
30
40
50
3.9
4.9
4.9
4.9
4.9
5.85
5.85
5.85
1.1
1.5
1.2
1
0.9
100
70
70
80
80
80
90
100
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
1
1
1
1
1
2
2
2
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
* *
* *
* *
* * *
* * *
* * * *
* * * *
* *No interference
* *
*
52.1 54.3
20.8 21.6
26.0 27.1
31.2
36.4
SQUARE
B2
BALL
DN
RADIUS
LU
TAPER
APMX
SOLID END MILLS
DC
Type
PRFRAD
Stock
Order Number
No. of Flutes
Unit : mm
J241

CARBIDE
VF2XLBS
VF2XLB
Work
material
AISI H13

Work
material
AISI D2
Neck Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut
R
length
PRFRAD (mm) LU (mm) (min-1) (mm/min) ap (mm)
(min-1) (mm/min) ap (mm)
R 0.1
R 0.15
R 0.2
R 0.25
SOLID END MILLS
R 0.3
R 0.4
R 0.5
R 0.6
R 0.7
R 0.75
0.5
1
1.5
2
2.5
1
1.5
2
2.5
3
4
1
1.5
2
2.5
3
4
5
1.5
2
3
4
5
6
2
3
4
5
6
7
8
2
3
4
6
8
10
3
4
5
6
8
10
12
14
16
18
20
6
8
10
12
14
16
8
12
16
6
8
10
12
14
16
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
30000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
36000
36000
36000
40000
40000
35000
30000
30000
30000
25000
40000
40000
40000
30000
25000
25000
40000
40000
40000
35000
30000
20000
20000
18000
18000
13000
13000
40000
40000
27000
16000
16000
15000
40000
32000
15000
40000
40000
40000
32000
16000
13000
300
300
300
200
100
500
500
500
400
300
200
1400
1000
1000
700
700
600
400
2000
2000
1200
900
700
600
2800
2800
2000
1000
800
600
400
3500
3000
3000
1600
1000
600
4000
4000
3000
2000
1600
1000
1000
600
500
300
250
4000
3000
1900
1100
850
500
4500
3000
1000
5000
5000
4500
3400
1500
1200
0.003
0.002
0.001
0.001
0.001
0.007
0.005
0.003
0.003
0.002
0.002
0.015
0.01
0.01
0.005
0.005
0.004
0.003
0.02
0.02
0.015
0.01
0.007
0.006
0.03
0.03
0.02
0.01
0.008
0.008
0.006
0.04
0.04
0.02
0.02
0.01
0.008
0.05
0.05
0.03
0.03
0.02
0.01
0.01
0.008
0.008
0.005
0.005
0.05
0.05
0.03
0.02
0.01
0.01
0.06
0.03
0.02
0.07
0.07
0.06
0.04
0.04
0.03
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
30000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
36000
36000
36000
40000
40000
35000
30000
30000
30000
25000
40000
40000
40000
30000
25000
25000
40000
40000
40000
35000
30000
20000
18000
18000
18000
13000
13000
35000
27000
24000
16000
16000
14000
28000
19000
14000
32000
28000
21000
19000
13000
13000
300
300
200
100
60
500
500
500
400
300
200
1400
1000
1000
700
700
500
300
2000
2000
1200
900
600
500
2800
2800
2000
1000
800
600
400
3500
3000
3000
1600
1000
600
4000
4000
3000
2000
1600
1000
800
480
400
240
200
3500
2000
1700
1000
780
400
3200
1800
800
4000
3500
2400
2000
1200
1200
0.002
0.002
0.001
0.001
0.001
0.005
0.003
0.002
0.002
0.001
0.001
0.01
0.006
0.006
0.003
0.003
0.003
0.002
0.015
0.015
0.01
0.007
0.005
0.004
0.02
0.02
0.015
0.007
0.005
0.005
0.004
0.03
0.03
0.015
0.01
0.007
0.005
0.04
0.04
0.02
0.02
0.01
0.01
0.008
0.008
0.006
0.004
0.004
0.04
0.04
0.02
0.01
0.01
0.006
0.05
0.02
0.01
0.06
0.06
0.04
0.03
0.03
0.02
AISI H13
AISI D2
Neck Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut
R
length
-1
PRFRAD (mm) LU
(min-1) (mm/min) ap (mm)
(mm) (min ) (mm/min) ap (mm)
18
R 0.75 20
R 0.8
R 0.9
R1
R 1.25
R 1.5
R 1.75
R2
R 2.5
R3
<0.1PRFRAD
Depth of cut
<0.2PRFRAD
8
12
16
20
8
12
16
20
6
8
10
12
14
16
18
20
22
25
30
35
10
15
20
25
30
35
8
10
12
14
16
20
25
30
35
40
16
20
25
30
35
40
10
12
14
16
20
25
30
35
40
45
50
20
25
30
35
30
40
50
13000
12000
40000
35000
13000
10000
40000
36000
25000
10000
40000
40000
40000
40000
40000
32000
24000
10000
10000
10000
10000
10000
36000
36000
26000
10000
8000
8000
32000
32000
32000
32000
32000
27000
21000
9000
6000
6000
28000
26000
23000
13000
9000
8500
24000
24000
24000
24000
24000
24000
20000
12000
11000
10000
8000
19000
19000
19000
16000
16000
16000
16000
1100
900
5000
3800
1200
750
5000
3800
2500
1000
6000
5000
5000
5000
5000
3500
2400
1000
1000
1000
800
500
5000
4600
3000
1100
800
500
6400
5100
5100
4500
4500
3800
2700
1000
700
600
4200
3800
3300
1900
1200
1100
4800
4800
3800
3800
3800
3800
3000
1700
1500
1300
1000
3400
3400
3200
2700
3500
3000
2700
0.02
0.02
0.08
0.05
0.04
0.02
0.09
0.06
0.04
0.03
0.1
0.1
0.08
0.08
0.06
0.05
0.04
0.04
0.04
0.04
0.02
0.02
0.12
0.08
0.07
0.06
0.05
0.03
0.15
0.15
0.13
0.13
0.1
0.1
0.08
0.08
0.06
0.04
0.13
0.13
0.12
0.09
0.08
0.07
0.2
0.2
0.15
0.15
0.15
0.15
0.1
0.1
0.1
0.08
0.05
0.2
0.2
0.15
0.1
0.2
0.15
0.15
10000
9000
26000
20000
12000
8000
25000
18000
14000
8000
24000
24000
24000
24000
21000
16000
13000
10000
10000
8000
8000
8000
20000
18000
13000
8000
7000
5000
16000
16000
16000
16000
16000
14000
11000
7000
6000
5000
14000
13000
11000
9000
6000
5500
12000
12000
12000
12000
12000
10000
10000
8000
5000
5000
4000
10000
10000
8000
8000
8000
8000
6000
800
700
3200
2100
1100
600
3100
1900
1300
800
3400
3000
3000
2600
2300
1700
1300
1000
1000
800
800
400
2600
2000
1400
800
700
400
3000
2200
2200
2200
1800
1600
1200
700
600
400
1600
1600
1200
1000
600
500
2200
2200
1500
1500
1500
1100
1100
900
500
500
400
1400
1400
1000
900
1000
800
500
0.02
0.01
0.07
0.03
0.02
0.01
0.08
0.04
0.025
0.02
0.1
0.1
0.07
0.05
0.05
0.03
0.03
0.03
0.02
0.02
0.015
0.01
0.11
0.075
0.05
0.04
0.03
0.03
0.15
0.15
0.13
0.1
0.1
0.06
0.06
0.05
0.04
0.03
0.13
0.11
0.08
0.07
0.06
0.04
0.2
0.2
0.15
0.15
0.15
0.1
0.08
0.08
0.06
0.05
0.04
0.2
0.2
0.15
0.1
0.2
0.15
0.15
(PRFRAD<1)
(PRFRAD>1)
ap
PRFRAD:Radius
J242
MIRACLE END MILLS
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
VC
30
Copper Alloy
CARBIDE
Aluminium Alloy
15
DC
DN
UWC
Type2
APMX
LU
DCON(h6)
PRFRAD
DN
LF
SQUARE
VC2ESB
0.15<PRFRAD<6
DC
PRFRAD
0.3<DC<12
APMX
LU
0
- 0.020
h6
Type2
LF
BALL
0.01
DCON(h6)

0
- 0.008
0
- 0.009
0
- 0.011
DC
APMX
LU
DN
LF
DCON
Stock
VC2ESBR0015N006
VC2ESBR0020N008
VC2ESBR0030N012
VC2ESBR0040N016
VC2ESBR0050
VC2ESBR0050N025
VC2ESBR0075
VC2ESBR0075N040
VC2ESBR0100
VC2ESBR0100N060
VC2ESBR0150
VC2ESBR0150N080
VC2ESBR0200
VC2ESBR0200N080
VC2ESBR0250
VC2ESBR0250N120
VC2ESBR0300
VC2ESBR0300N130
VC2ESBR0350
VC2ESBR0400
VC2ESBR0500
VC2ESBR0600
0.15
0.2
0.3
0.4
0.5
0.5
0.75
0.75
1
1
1.5
1.5
2
2
2.5
2.5
3
3
3.5
4
5
6
0.3
0.4
0.6
0.8
1
1
1.5
1.5
2
2
3
3
4
4
5
5
6
6
7
8
10
12
0.3
0.4
0.6
0.8
1
1
1.5
1.5
2
2
3
3
4
4
5
5
6
6
7
8
10
12
0.6
0.8
1.2
1.6
2.5
12
13
0.27
0.36
0.56
0.76
0.94
1.44
1.9
2.9
3.9
4.9
5.85
30
30
30
30
30
30
30
30
40
40
40
40
40
40
40
40
40
40
50
50
60
65
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
8
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
2
2
TAPER
PRFRAD
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute ball nose end mill for high rigidity.
J243
MIRACLE END MILLS

CARBIDE
VC2ESB

material
AISI H13
%>15
% < 15
R
PRFRAD
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
R 0.5
R 0.75
R1
R 1.5
R2
R 2.5
R3
R4
R5
R6
40000
40000
40000
40000
32000
25000
21000
16000
13000
9000
5600
6500
6500
7500
7500
6000
5800
4500
3600
2500
40000
40000
39000
27000
20000
16000
13000
10000
8000
6000
3200
3200
3800
4300
3600
2900
2600
2000
1700
1300
Depth of cut
(mm)
0.06
0.09
0.11
0.13
0.15
0.20
0.25
0.30
0.50
0.50
%>15
% < 15
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
40000
40000
40000
32000
25000
20000
17000
13000
10000
7200
5600
6500
6500
6000
6000
5400
4700
3600
2900
2000
40000
32000
31000
22000
16000
13000
10000
8000
6400
4800
3000
3200
3500
3400
2700
2300
2000
1500
1200
1000
Depth of cut
(mm)
0.06
0.09
0.11
0.13
0.15
0.20
0.25
0.30
0.50
0.50
< 0.2PRFRAD
Depth of
cut
< Please
PRFRAD:Radius

SOLID END MILLS
End mill
pf
y Using general machining center or NC milling machine.

Roughing (Depth of cut < 0.8R)
Work
material
J244


Pre-hardened steel
R
PRFRAD (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
R 0.5
R 1
R 2
R 3
R 4
R 5
R 6
R 8
R10
R12.5
8800
5800
4200
3200
2500
2100
1500
1200
950
150
280
340
360
340
300
210
170
130
7000
4400
3100
2400
1900
1600
1200
960
770
110
230
240
280
260
220
170
130
110
ap
PRFRAD
MIRACLE END MILLS

CARBIDE
Titanium Alloy,
Aluminium Alloy
20
10
APMX
LU
15
DC
PRFRAD APMX
LU
0.005
0
- 0.01
h5

0
- 0.005
0
- 0.006
APMX
LU
PRFRAD
Type3
LF
DC
0.1<DC<12
Type2
BALL
0.05<PRFRAD<6
DN
Type1
LF
DN
PRFRAD
Copper Alloy
SQUARE
Austenitic
Stainless Steel
DCON(h5)
30
DCON(h5)
Hardened Steel
(>55HRC)
DC
Hardened Steel
( < 55HRC)
DN
(<30HRC)
( < 45HRC)
VC
UWC
DCON(h5)
VC2PSB
LF
0
- 0.008
DC
APMX
LU
DN
LF
DCON
Stock
Type
VC2PSBR0005
VC2PSBR0010
VC2PSBR0015
VC2PSBR0020
VC2PSBR0025
VC2PSBR0030
VC2PSBR0035
VC2PSBR0040
VC2PSBR0045
VC2PSBR0050
VC2PSBR0060
VC2PSBR0070
VC2PSBR0075
VC2PSBR0080
VC2PSBR0090
VC2PSBR0100
VC2PSBR0150
VC2PSBR0200
VC2PSBR0250
VC2PSBR0300
VC2PSBR0400
VC2PSBR0500
VC2PSBR0600
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
0.6
0.7
0.75
0.8
0.9
1
1.5
2
2.5
3
4
5
6
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.2
1.4
1.5
1.6
1.8
2
3
4
5
6
8
10
12
0.2
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.5
1.8
2.1
2.3
2.4
2.7
3
4.5
6
7.5
9
12
15
18
0.5
0.8
1
1.3
1.5
1.8
2
2.3
2.5
3
3.5
3.8
4
4.5
5
7.5
10
12.5
15
20
25
30
0.17
0.27
0.36
0.46
0.56
0.66
0.76
0.86
0.94
1.14
1.34
1.44
1.54
1.74
1.90
2.90
3.90
4.90
5.85
7.85
9.70
11.70
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
70
70
80
80
90
100
110
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
3
3
3
3
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
TAPER
PRFRAD
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute ball nose end mill with high precision radial tolerance 0.005mm.
J245
MIRACLE END MILLS
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Titanium Alloy,
30
Austenitic
Stainless Steel
DC
SQUARE
Hardened Steel
( < 55HRC)
VC
UWC
DN
Inspection reports regarding the R accuracy of the

VC2PSBP are supplied with the tool.
Aluminium Alloy
20
APMX
LU
PRFRAD
Copper Alloy
Type1
10( R0.020.04 is 7.)

DCON(h5)
VC2PSBP
Ball nose end mill, Short cut length, 2 flute, Ultra high precision
DN
CARBIDE
LF
0.1<DC<12
0
- 0.01
h5
PRFRAD

0
- 0.005
0
- 0.006
LF
APMX
LU
DCON(h5)
R0.02 0.04
Top edge geometry
10
7
0.002
DN
0.02<PRFRAD<6
APMX
LU
DC
BALL
PRFRAD
DCON(h5)
DC
15
LF
0
- 0.008
Type2
Type3
a 2 flute ball nose end mill with ultra high precision radial tolerance 0.002mm.
Order Number
PRFRAD
DC
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VC2PSBPR0002
VC2PSBPR0003
VC2PSBPR0004
VC2PSBPR0005
VC2PSBPR0010
VC2PSBPR0015
VC2PSBPR0020
VC2PSBPR0025
VC2PSBPR0030
VC2PSBPR0035
VC2PSBPR0040
VC2PSBPR0045
VC2PSBPR0050
VC2PSBPR0060
VC2PSBPR0070
VC2PSBPR0075
VC2PSBPR0080
VC2PSBPR0090
VC2PSBPR0100
VC2PSBPR0150
VC2PSBPR0200
VC2PSBPR0250
VC2PSBPR0300
VC2PSBPR0400
VC2PSBPR0500
VC2PSBPR0600
0.02
0.03
0.04
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
0.6
0.7
0.75
0.8
0.9
1
1.5
2
2.5
3
4
5
6
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.2
1.4
1.5
1.6
1.8
2
3
4
5
6
8
10
12
0.06
0.09
0.12
0.2
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.5
1.8
2.1
2.3
2.4
2.7
3
4.5
6
7.5
9
12
15
18
0.5
0.8
1
1.3
1.5
1.8
2
2.3
2.5
3
3.5
3.8
4
4.5
5
7.5
10
12.5
15
20
25
30
0.17
0.27
0.36
0.46
0.56
0.66
0.76
0.86
0.94
1.14
1.34
1.44
1.54
1.74
1.9
2.9
3.9
4.9
5.85
7.85
9.7
11.7
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
70
70
80
80
90
100
110
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
[0.002mm]
J246
r
r
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
3
3
3
3
VC2PSBP
VC2PSB
Ball nose end mill, Short cut length, 2 flute, Ultra high precision Ball nose end mill, Short cut length, 2 flute, High precision
CARBIDE


material
AISI H13
%>15
% < 15
%>15
% < 15
R
PRFRAD
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
R0.05
R0.1
R0.15
R0.2
R0.25
R0.3
R0.35
R0.4
R0.45
R0.5
R0.75
R1
R1.5
R2
R2.5
R3
R4
R5
R6
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
35000
30000
25000
23000
20000
15000
12000
10000
200
600
900
1000
1500
2000
2800
2800
3200
3200
3600
3500
3400
3400
3400
3400
3000
3000
2600
40000
40000
40000
40000
40000
40000
40000
38000
35000
30000
25000
23000
20000
17000
15000
12500
10000
8300
400
600
700
1000
1500
2100
2100
2200
2200
2300
2200
2200
2200
2200
2200
2000
2000
1800
40000
40000
40000
40000
40000
40000
40000
40000
38000
35000
32000
28000
24000
20000
18000
16000
10000
8000
6600
170
600
900
1000
1500
2000
2800
2800
3000
3000
3000
2800
2600
2600
2600
2600
2000
2000
1700
40000
40000
40000
40000
40000
37000
35000
32000
30000
25000
20000
16000
14000
12000
10000
7500
6000
5000
400
600
700
1000
1500
1800
1800
1800
1800
1800
1700
1500
1500
1500
1400
1200
1200
1100
End mill
PRFRAD
%
< 0.06PRFRAD
PRFRAD:Radius
pf

SOLID END MILLS
Depth of
cut
ap
< 0.1PRFRAD
J247
MIRACLE END MILLS
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
30
Aluminium Alloy
SQUARE
DC
15
APMX
PRFRAD
0.01
0.02
DC < 12
DC>12
0
- 0.020
h6
0
- 0.030
PRFRAD
APMX
DCON=3 4 < DCON < 6 8<DCON<10 12<DCON<16 20<DCON<25

0
- 0.006
0
- 0.008
0
- 0.009
0
- 0.011
Type2
Type3
LF
DC
BALL
APMX
Type1
LF
DC
PRFRAD
DCON(h6)
(<30HRC)
( < 45HRC)
VC
UWC
DCON(h6)
VC2MB
DCON(h6)
CARBIDE
LF
0
- 0.013
SOLID END MILLS
TAPER
VC2MBR0020
VC2MBR0025
VC2MBR0030
VC2MBR0040
VC2MBR0050
VC2MBR0060
VC2MBR0070
VC2MBR0075
VC2MBR0080
VC2MBR0090
VC2MBR0100
VC2MBR0150
VC2MBR0200
VC2MBR0250
VC2MBR0300
VC2MBR0350
VC2MBR0400
VC2MBR0450
VC2MBR0500
VC2MBR0600
VC2MBR0700
VC2MBR0750
VC2MBR0800
VC2MBR0900
VC2MBR1000
VC2MBR1250
J248
PRFRAD
DC
APMX
LF
DCON
Stock
Order Number
No. of
Flutes
RADIUS
Unit : mm
0.2
0.25
0.3
0.4
0.5
0.6
0.7
0.75
0.8
0.9
1
1.5
2
2.5
3
3.5
4
4.5
5
6
7
7.5
8
9
10
12.5
0.4
0.5
0.6
0.8
1
1.2
1.4
1.5
1.6
1.8
2
3
4
5
6
7
8
9
10
12
14
15
16
18
20
25
0.8
1
1.2
1.6
2.5
3
3
4
4
5
6
8
8
12
12
14
14
18
18
22
26
30
30
34
38
55
38
38
38
38
40
40
40
40
40
40
60
70
70
80
80
90
90
100
100
110
120
140
140
140
160
180
3
3
3
3
4
4
4
4
4
4
6
6
6
6
6
8
8
10
10
12
12
16
16
16
20
25
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
2
2
3
1
2
3
2
2
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
APMX
LF
DC
DN
PRFRAD
0.01
0.02
DC < 12
DC>12
0
- 0.020
h6
PRFRAD
0
- 0.030
PRFRAD
DCON=3 4 < DCON < 6 8<DCON<10 12<DCON<16 20<DCON<25

0
- 0.006
0
- 0.008
0
- 0.009
0
- 0.011
Type2
Type3
LF
DC
APMX
LU
Type1
APMX
LF
BALL
SQUARE
Hardened Steel
(>55HRC)
CARBIDE
DCON(h6)
Hardened Steel
( < 55HRC)
30
DCON(h6)
(<30HRC)
( < 45HRC)
VC
UWC
DCON(h6)
VC2MDB
Ball nose, Medium cut length, 2 flute, Strong geometry type
0
- 0.013
DC
APMX
LU
DN
LF
DCON
Stock
VC2MDBR0150S03
VC2MDBR0150
VC2MDBR0200S04
VC2MDBR0200
VC2MDBR0250
VC2MDBR0300
VC2MDBR0350
VC2MDBR0400
VC2MDBR0500
VC2MDBR0600
VC2MDBR0700
VC2MDBR0800
VC2MDBR0900
VC2MDBR1000
VC2MDBR1250
1.5
1.5
2
2
2.5
3
3.5
4
5
6
7
8
9
10
12.5
3
3
4
4
5
6
7
8
10
12
14
16
18
20
25
8
8
8
8
12
12
14
14
18
22
26
30
34
38
55
14
14
22
27
31
35
50
58
75
2.9
3.9
5.85
7.85
9.7
11.7
15.5
19.5
24.5
70
70
70
70
80
80
90
90
100
110
120
140
140
160
180
3
6
4
6
6
6
8
8
10
12
12
16
16
20
25
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
1
2
1
1
2
1
2
2
2
3
2
3
2
2
TAPER
PRFRAD
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute ball nose end mill with high edge strength resistant to chipping.
J249
MIRACLE END MILLS

CARBIDE
VC2MB
VC2MDB
Ball nose, Medium cut length, 2 flute, Strong geometry type

material
AISI H13
%>15
% < 15
R
PRFRAD
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
R 0.5
R 0.75
R1
R 1.5
R2
R 2.5
R3
R4
R5
R6
40000
40000
40000
40000
32000
25000
21000
16000
13000
9000
5600
6500
6500
7500
7500
6000
5800
4500
3600
2500
40000
40000
39000
27000
20000
16000
13000
10000
8000
6000
3200
3200
3800
4300
3600
2900
2600
2000
1700
1300
Depth of cut
(mm)
0.06
0.09
0.11
0.13
0.15
0.20
0.25
0.30
0.50
0.50
%>15
% < 15
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
40000
40000
40000
32000
25000
20000
17000
13000
10000
7200
5600
6500
6500
6000
6000
5400
4700
3600
2900
2000
40000
32000
31000
22000
16000
13000
10000
8000
6400
4800
3000
3200
3500
3400
2700
2300
2000
1500
1200
1000
Depth of cut
(mm)
0.06
0.09
0.11
0.13
0.15
0.20
0.25
0.30
0.50
0.50
< 0.2PRFRAD
Depth of
cut
< Please
PRFRAD:Radius

SOLID END MILLS
End mill
pf
y Using general machining center or NC milling machine.

Roughing (Depth of cut < 0.8R)
Work
material
J250


Pre-hardened steel
R
PRFRAD (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
R 0.5
R 1
R 2
R 3
R 4
R 5
R 6
R 8
R10
R12.5
8800
5800
4200
3200
2500
2100
1500
1200
950
150
280
340
360
340
300
210
170
130
7000
4400
3100
2400
1900
1600
1200
960
770
110
230
240
280
260
220
170
130
110
ap
PRFRAD
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
DN
Hardened Steel
( < 55HRC)
30
DC
0.5<PRFRAD<6
LF
BHTA
Type2
PRFRAD
APMX
LU
LF

0
- 0.009
DCON(h6)
Inclined angle
0
- 0.020
0
- 0.008
B2
DC
0.01
1 < DC < 12
h6
APMX
LU
Effective
length
DCON(h6)
Type1
PRFRAD
Effective length
for inclined angle
B2
BHTA
SQUARE
(<30HRC)
( < 45HRC)
VC
UWC
BALL
VCXB
0
- 0.011
1
1
1
130'
3
5
1
1
1
130'
3
5
1
1
1
130'
3
1
1
1
130'
3
1
1
130'
3
1
1
1
130'
3
1
1
130'
2
2
2
2
2
2
4
4
4
4
4
4
6
6
6
6
6
8
8
8
8
8
10
10
10
10
12
12
12
12
12
14
14
14
DN
LF
DCON
16
21
26
23
42
23
21
31
41
23
41
23
31
41
51
52
32
36
46
60
49
28
36
65
61
41
51
65
92
53
34
68
92
55
6.6
5.4
4.6
5.1
3.4
5.8
4.6
3.4
2.7
4.4
2.9
4.9
2.7
2.1
1.7
1.7
2.8
1.7
1.3
1
1.3
2.2
0.9
1.4
1.5
2.3
1.2
1
1.3
1.2
1.9
0.9
1.3
1.2
1.38
1.56
1.73
1.97
5.08
4.46
2.43
2.78
3.13
2.8
5.71
5.02
3.71
4.06
4.41
5.21
5.56
4.81
5.16
5.65
5.95
5.71
6.72
7.42
7.11
7.6
8.54
7.85
9.64
10.47
9.85
50
60
70
60
80
60
50
60
70
60
80
60
60
70
80
90
70
70
80
90
90
70
80
110
110
90
90
110
140
110
90
110
140
120
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
10
8
8
10
12
10
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
2
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
16.2
21.2
26.2
21.3
31.3
41.3
31.4
41.4
51.4
36.5
46.5
60.5
17
22.3
27.6
23.9
22.4
33
43.5
24.1
33
43.5
18
23.5
29.1
25.2
42.4
23.6
34.8
25.4
*
*
* *
* *
*
* *
* *
* *
* *
*
*
*
*
65.6
*
*
*
*
*
51.8
* *
65.8
* *
92.8
* *
* *
*
* * *
92.8
* *
* *
* No interference
TAPER
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
4
4
4
4
4
5
5
5
5
6
6
6
6
6
8
8
8
B2
SOLID END MILLS
0.5
0.5
0.5
0.5
0.5
0.5
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2.5
2.5
2.5
2.5
3
3
3
3
3
4
4
4
LU
Type
VCXBR0050T0100L016
VCXBR0050T0100L021
VCXBR0050T0100L026
VCXBR0050T0130
VCXBR0050T0300
VCXBR0050T0500
VCXBR0100T0100L021
VCXBR0100T0100L031
VCXBR0100T0100L041
VCXBR0100T0130
VCXBR0100T0300
VCXBR0100T0500
VCXBR0150T0100L031
VCXBR0150T0100L041
VCXBR0150T0100L051
VCXBR0150T0130
VCXBR0150T0300
VCXBR0200T0100L036
VCXBR0200T0100L046
VCXBR0200T0100L060
VCXBR0200T0130
VCXBR0200T0300
VCXBR0250T0100L036
VCXBR0250T0100L065
VCXBR0250T0130
VCXBR0250T0300
VCXBR0300T0100L051
VCXBR0300T0100L065
VCXBR0300T0100L092
VCXBR0300T0130
VCXBR0300T0300
VCXBR0400T0100L068
VCXBR0400T0100L092
VCXBR0400T0130
PRFRAD DC BHTA APMX
Stock
Order Number
No. of Flutes
Unit : mm
RADIUS
a 2 flute taper end mill with taper neck.
J251
MIRACLE END MILLS
VCXB
VCXBR0400T0300
VCXBR0500T0100L070
VCXBR0500T0100L100
VCXBR0500T0130
VCXBR0500T0300
VCXBR0600T0100L070
VCXBR0600T0100L100
VCXBR0600T0130
VCXBR0600T0300
4
5
5
5
5
6
6
6
6
3
1
1
130'
3
1
1
130'
3
14
18
18
18
18
22
22
22
22
DN
LF
DCON
36
70
100
59
40
70
100
83
63
1.8
0.9
1.8
1.1
1.7
1.8
1.2
1.5
2.1
11.76
12.8
13.62
14.66
15.08
100
130
160
130
110
140
160
160
140
10
12
16
12
12
16
16
16
16
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
Type
B2
Effective length
for inclined angle
TAPER
SOLID END MILLS
*
*
*
*
*
* *
* *
* *
*
No interference
1
1 100.7
2
1 70.9
1 100.9
1
J252
8
10
10
10
10
12
12
12
12
LU
Stock
PRFRAD DC BHTA APMX
RADIUS
BALL
SQUARE
Order Number
Unit : mm
No. of Flutes
CARBIDE
*
*
*
CARBIDE
Work material
R
PRFRAD
(mm)
R0.5
R1
R2
R3
R4
R5
R6
Depth of cut
Taper angle
one side
DN
Neck length
LU
(mm)
ap
(mm)
1
1
1
130'
3
5
1
1
1
130'
3
5
1
1
1
130'
3
1
1
1
130'
3
130'
3
1
1
130'
3
1
1
130'
3
16
21
26
23
42
23
21
31
41
23
41
23
36
46
60
49
28
51
65
92
53
34
55
36
70
100
59
40
70
100
83
63
0.02
0.01
0.01
0.02
0.05
0.05
0.05
0.04
0.03
0.1
0.1
0.1
0.2
0.15
0.1
0.2
0.2
0.3
0.2
0.1
0.3
0.3
0.4
0.4
0.4
0.3
0.5
0.5
0.6
0.4
0.6
0.6

Pre-hardened steel
AISI H13
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
0.1
22000
530
12000
230
0.2
18000
570
10000
260
0.8
14000
670
6000
200
1.2
10000
840
5000
220
1.6
8000
840
4000
270
6000
840
3000
310
2.4
5000
900
2500
340
ae
(mm)
SOLID END MILLS
ae
Depth of cut
ap
J253
CRN END MILLS

CARBIDE
CRN2MB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
UWC
Titanium Alloy,
CRN
30
Copper Alloy
Aluminium Alloy
Type1
PRFRAD
DCON(h6)
DC
SQUARE
15
APMX
0.2<PRFRAD<6
0.01
PRFRAD
Type2
DCON(h6)
BALL
DC
LF
APMX
LF
0.4<DC<12
0
- 0.02
h6
DCON=3 4 < DCON < 6 8<DCON<10 DCON=12

0
- 0.006
0
- 0.008
0
- 0.009
0
- 0.011
a 2 flute ball nose end mill with CRN coating for copper electrode machining.
J254
Order Number
PRFRAD
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
CRN2MBR0020S04
CRN2MBR0020S06
CRN2MBR0030S04
CRN2MBR0030S06
CRN2MBR0040S04
CRN2MBR0040S06
CRN2MBR0050S04
CRN2MBR0050S06
CRN2MBR0075S04
CRN2MBR0075S06
CRN2MBR0100S06
CRN2MBR0125S06
CRN2MBR0150S03
CRN2MBR0150S06
CRN2MBR0175S06
CRN2MBR0200S04
CRN2MBR0200S06
CRN2MBR0250S06
CRN2MBR0300S06
CRN2MBR0400S08
CRN2MBR0500S10
CRN2MBR0600S12
0.2
0.2
0.3
0.3
0.4
0.4
0.5
0.5
0.75
0.75
1
1.25
1.5
1.5
1.75
2
2
2.5
3
4
5
6
0.4
0.4
0.6
0.6
0.8
0.8
1
1
1.5
1.5
2
2.5
3
3
3.5
4
4
5
6
8
10
12
0.8
0.8
1.2
1.2
1.6
1.6
2.5
2.5
4
4
6
6
8
8
8
8
8
12
12
14
18
22
45
50
45
50
45
50
45
50
45
50
50
50
70
70
70
70
70
80
80
90
100
110
4
6
4
6
4
6
4
6
4
6
6
6
3
6
6
4
6
6
6
8
10
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
2
2
2
2
CARBIDE

Work
material
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
R0.2
R0.3
R0.4
R0.5
R0.75
R1
R1.25
R1.5
R2
R2.5
R3
R4
R5
R6
40000
40000
40000
40000
40000
40000
40000
40000
32000
25000
21000
16000
13000
9000
1600
3200
6400
8000
9600
9600
12000
12000
11000
9000
8400
6400
5200
3600
40000
40000
40000
40000
40000
39000
30000
27000
20000
16000
13000
10000
8000
6000
1200
1600
2400
3200
4000
4700
4500
4300
3600
2900
2600
2000
1700
1300
Depth of
cut
Depth of cut
ap(mm)
0.02
0.03
0.05
0.06
0.09
0.11
0.12
0.13
0.15
0.20
0.25
0.30
0.50
0.50
PRFRAD
< 0.2PRFRAD
%
< ap
PRFRAD:Radius
1)
2)
3)
4)
End mill
pf
% is the inclination angle of the machined surface.

SOLID END MILLS
Revolution
(min-1)
ap
%>15
% < 15
R
PRFRAD
(mm)
J255
CRN COATED END MILLS

CARBIDE
CRN2XLB
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Titanium Alloy,
Austenitic
Stainless Steel
30
Copper Alloy
Aluminium Alloy
Type1
DC
SQUARE
DN
(<30HRC)
( < 45HRC)
CRN
UWC
DN
DC
0.1<PRFRAD<3
0.01
0.2 < DC < 6
Type2
PRFRAD
Inclined angle
0
- 0.02
h6
LF
APMX
LU
DCON(h6)
BALL
APMX
LU
Effective
length
Effective length
for inclined angle
15
DCON(h6)
PRFRAD
LF
4 < DCON < 6

0
- 0.008
a 2 flute long neck ball nose end mill with CRN coating for copper electrode machining.
DC
APMX
CRN2XLBR0010N005S04
CRN2XLBR0010N005S06
CRN2XLBR0010N010S04
CRN2XLBR0010N010S06
CRN2XLBR0010N015S04
CRN2XLBR0010N015S06
CRN2XLBR0015N010S04
CRN2XLBR0015N010S06
CRN2XLBR0015N015S04
CRN2XLBR0015N015S06
CRN2XLBR0015N020S04
CRN2XLBR0015N020S06
CRN2XLBR0020N010S04
CRN2XLBR0020N010S06
CRN2XLBR0020N015S04
CRN2XLBR0020N015S06
CRN2XLBR0020N020S04
CRN2XLBR0020N020S06
CRN2XLBR0020N030S04
CRN2XLBR0020N030S06
CRN2XLBR0025N015S04
CRN2XLBR0025N015S06
CRN2XLBR0025N020S04
CRN2XLBR0025N020S06
CRN2XLBR0025N030S04
CRN2XLBR0025N030S06
CRN2XLBR0025N040S04
CRN2XLBR0025N040S06
CRN2XLBR0025N060S04
CRN2XLBR0025N060S06
CRN2XLBR0025N080S04
CRN2XLBR0025N080S06
CRN2XLBR0025N100S04
CRN2XLBR0025N100S06
0.1
0.1
0.1
0.1
0.1
0.1
0.15
0.15
0.15
0.15
0.15
0.15
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
J256
LU
DN
LF
DCON
0.5
0.5
1
1
1.5
1.5
1
1
1.5
1.5
2
2
1
1
1.5
1.5
2
2
3
3
1.5
1.5
2
2
3
3
4
4
6
6
8
8
10
10
0.17
0.17
0.17
0.17
0.17
0.17
0.27
0.27
0.27
0.27
0.27
0.27
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.36
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
PRFRAD
Stock
Order Number
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
Unit : mm
Effective length
for inclined angle
30'
1 0.5 0.5
1 0.5 0.5
1 1
1.1
1 1
1.1
1 1.5 1.6
1 1.5 1.6
1 1
1.1
1 1
1.1
1 1.5 1.6
1 1.5 1.6
1 2.1 2.2
1 2.1 2.2
1 1
1
1 1
1
1 1.5 1.6
1 1.5 1.6
1 2
2.1
1 2
2.1
1 3.1 3.2
1 3.1 3.2
1 1.5 1.6
1 1.5 1.6
1 2
2.1
1 2
2.1
1 3.1 3.2
1 3.1 3.2
1 4.1 4.3
1 4.1 4.3
1 6.2 6.4
1 6.2 6.4
1 8.3 8.5
1 8.3 8.5
1 10.3 10.7
1 10.3 10.7
0.6
0.6
1.2
1.2
1.7
1.7
1.2
1.2
1.7
1.7
2.3
2.3
1.1
1.1
1.7
1.7
2.3
2.3
3.4
3.4
1.7
1.7
2.3
2.3
3.4
3.4
4.6
4.6
6.9
6.9
9.2
9.2
11.5
11.5
0.6
0.6
1.3
1.3
1.9
1.9
1.3
1.3
1.9
1.9
2.5
2.5
1.2
1.2
1.8
1.8
2.5
2.5
3.7
3.7
1.8
1.8
2.4
2.4
3.7
3.7
4.9
4.9
7.4
7.4
9.9
9.9
12.4
12.4
CARBIDE
DCON
CRN2XLBR0030N020S04
CRN2XLBR0030N020S06
CRN2XLBR0030N040S04
CRN2XLBR0030N040S06
CRN2XLBR0030N060S04
CRN2XLBR0030N060S06
CRN2XLBR0030N080S04
CRN2XLBR0030N080S06
CRN2XLBR0030N100S04
CRN2XLBR0030N100S06
CRN2XLBR0040N020S04
CRN2XLBR0040N020S06
CRN2XLBR0040N040S04
CRN2XLBR0040N040S06
CRN2XLBR0040N060S04
CRN2XLBR0040N060S06
CRN2XLBR0040N080S04
CRN2XLBR0040N080S06
CRN2XLBR0040N100S04
CRN2XLBR0040N100S06
CRN2XLBR0050N030S04
CRN2XLBR0050N030S06
CRN2XLBR0050N040S04
CRN2XLBR0050N040S06
CRN2XLBR0050N050S04
CRN2XLBR0050N050S06
CRN2XLBR0050N060S04
CRN2XLBR0050N060S06
CRN2XLBR0050N070S04
CRN2XLBR0050N070S06
CRN2XLBR0050N080S04
CRN2XLBR0050N080S06
CRN2XLBR0050N100S04
CRN2XLBR0050N100S06
CRN2XLBR0050N120S04
CRN2XLBR0050N120S06
CRN2XLBR0050N140S04
CRN2XLBR0050N140S06
CRN2XLBR0050N160S04
CRN2XLBR0050N160S06
CRN2XLBR0050N180S04
CRN2XLBR0050N180S06
CRN2XLBR0050N200S04
CRN2XLBR0050N200S06
CRN2XLBR0075N080S04
CRN2XLBR0075N080S06
CRN2XLBR0075N100S04
CRN2XLBR0075N100S06
CRN2XLBR0075N120S04
CRN2XLBR0075N120S06
CRN2XLBR0075N140S04
CRN2XLBR0075N140S06
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
4
4
6
6
8
8
10
10
2
2
4
4
6
6
8
8
10
10
3
3
4
4
5
5
6
6
7
7
8
8
10
10
12
12
14
14
16
16
18
18
20
20
8
8
10
10
12
12
14
14
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
55
55
55
55
60
55
60
50
50
50
50
50
50
50
55
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
2.1
2.1
4.2
4.2
6.3
6.3
8.3
8.3
10.4
10.4
2.1
2.1
4.2
4.2
6.3
6.3
8.3
8.3
10.4
10.4
3.2
3.2
4.2
4.2
5.3
5.3
6.3
6.3
7.4
7.4
8.4
8.4
10.5
10.5
12.6
12.6
14.7
14.7
16.8
16.8
18.9
18.9
20.9
20.9
8.4
8.4
10.5
10.5
12.6
12.6
14.7
14.7
2.2
2.2
4.3
4.3
6.5
6.5
8.6
8.6
10.8
10.8
2.2
2.2
4.3
4.3
6.5
6.5
8.6
8.6
10.8
10.8
3.3
3.3
4.4
4.4
5.5
5.5
6.6
6.6
7.7
7.7
8.8
8.8
10.9
10.9
13.1
13.1
15.2
15.2
17.4
17.4
19.5
19.5
21.6
21.6
8.8
8.8
10.9
10.9
13.1
13.1
15.2
15.2
2.3
2.3
4.6
4.6
6.9
6.9
9.2
9.2
11.5
11.5
2.3
2.3
4.6
4.6
6.9
6.9
9.2
9.2
11.5
11.5
3.6
3.6
4.8
4.8
6
6
7.1
7.1
8.3
8.3
9.4
9.4
11.7
11.7
14
14
16.3
16.3
18.6
18.6
20.9
20.9
23.2
23.2
9.4
9.4
11.7
11.7
14
14
16.3
16.3
2.5
2.5
5
5
7.5
7.5
10
10
12.5
12.5
2.5
2.5
5
5
7.5
7.5
10
10
12.4
12.4
3.9
3.9
5.2
5.2
6.4
6.4
7.7
7.7
8.9
8.9
10.2
10.2
12.6
12.6
15.1
15.1
17.6
17.6
20.1
20.1
22.6
22.6
25.1
25.1
10.1
10.1
12.6
12.6
15.1
15.1
17.6
17.6
SQUARE
LF
BALL
DN
RADIUS
LU
TAPER
APMX
SOLID END MILLS
DC
Type
PRFRAD
Stock
Order Number
No. of Flutes
Unit : mm
J257
CRN COATED END MILLS
CRN2XLB
DC
APMX
LU
DN
LF
DCON
CRN2XLBR0075N160S04
CRN2XLBR0075N160S06
CRN2XLBR0075N180S04
CRN2XLBR0075N180S06
CRN2XLBR0075N200S04
CRN2XLBR0075N200S06
CRN2XLBR0100N080S04
CRN2XLBR0100N080S06
CRN2XLBR0100N100S04
CRN2XLBR0100N100S06
CRN2XLBR0100N120S04
CRN2XLBR0100N120S06
CRN2XLBR0100N140S04
CRN2XLBR0100N140S06
CRN2XLBR0100N160S04
CRN2XLBR0100N160S06
CRN2XLBR0100N200S04
CRN2XLBR0100N200S06
CRN2XLBR0100N250S06
CRN2XLBR0100N300S06
CRN2XLBR0150N160S06
CRN2XLBR0150N250S06
CRN2XLBR0150N350S06
CRN2XLBR0200N160S06
CRN2XLBR0200N200S06
CRN2XLBR0200N300S06
CRN2XLBR0200N400S06
CRN2XLBR0200N500S06
CRN2XLBR0250N200S06
CRN2XLBR0250N300S06
CRN2XLBR0300N300S06
CRN2XLBR0300N500S06
0.75
0.75
0.75
0.75
0.75
0.75
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
2
2
2
2
2
2.5
2.5
3
3
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
4
4
4
4
4
5
5
6
6
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
4
4
4
4
4
5
5
6
6
16
16
18
18
20
20
8
8
10
10
12
12
14
14
16
16
20
20
25
30
16
25
35
16
20
30
40
50
20
30
30
50
1.44
1.44
1.44
1.44
1.44
1.44
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
1.90
2.90
2.90
2.90
3.90
3.90
3.90
3.90
3.90
4.90
4.90
5.85
5.85
55
55
55
60
55
60
50
50
50
50
50
50
50
55
55
55
60
60
65
70
60
70
80
70
70
70
90
100
70
80
80
100
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Type
PRFRAD
Stock
Order Number
J258
Unit : mm
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
16.8
16.8
18.8
18.8
20.9
20.9
8.3
8.3
10.4
10.4
12.5
12.5
14.6
14.6
16.7
16.7
20.8
20.8
26
31.1
16.6
26
36.3
16.6
20.8
31.1
41.4
51.8
20.7
31.1
17.3
17.3
19.5
19.5
21.6
21.6
8.7
8.7
10.8
10.8
12.9
12.9
15.1
15.1
17.2
17.2
21.5
21.5
26.8
32.2
17.2
26.8
37.5
17.1
21.4
32.1
42.8
53.5
21.4
18.6
18.6
20.9
20.9
23.2
23.2
9.2
9.2
11.5
11.5
13.8
13.8
16.1
16.1
18.4
18.4
23
23
28.8
34.5
18.4
28.7
40.2
18.3
22.9
20
20
22.5
22.5
*
*
25
9.9
9.9
12.4
12.4
14.9
14.9
17.4
17.4
19.9
19.9
24.8
31
37.3
19.7
*
*
19.6
*
* *
* *
* *
* *
* * *
* * *
*No interference
* *
CARBIDE
Neck length
R
PRFRAD (mm) LU (mm)
R0.1
R0.15
R0.2
R0.25
R0.3
R0.4
R0.5
0.5
1.0
1.5
1
2
1
2
3
2
4
6
10
2
6
10
4
6
10
4
6
8
10
16
20
Work material
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap(mm)
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
36000
26000
40000
40000
30000
40000
40000
30000
40000
40000
40000
33000
18000
13000
800
600
400
1200
800
2000
1300
800
2000
1200
600
200
3200
1200
500
4000
2500
700
6400
4800
3000
2000
500
250
0.003
0.002
0.001
0.007
0.003
0.015
0.01
0.005
0.02
0.01
0.006
0.002
0.03
0.008
0.003
0.02
0.02
0.008
0.05
0.03
0.02
0.01
0.008
0.005
Neck length
R
PRFRAD (mm) LU (mm)
R0.75
R1
R1.5
R2
R2.5
R3
8
12
16
20
8
10
12
16
20
30
16
25
35
16
20
30
40
50
20
30
30
50
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap(mm)
40000
35000
20000
12000
40000
40000
40000
30000
20000
10000
40000
25000
6000
32000
32000
20000
15000
8000
25000
20000
21000
20000
8000
4500
2000
900
9600
6400
6000
3000
2000
800
12000
6000
700
11000
9000
4500
3000
1000
9500
3300
8400
3000
0.07
0.04
0.03
0.02
0.10
0.08
0.08
0.05
0.04
0.02
0.10
0.08
0.06
0.15
0.15
0.10
0.08
0.05
0.20
0.15
0.20
0.15
< 0.2PRFRAD
Depth of cut
< ap
PRFRAD:Radius
SOLID END MILLS
Work material
J259
DF END MILLS
DF2MB
UWC
Copper Alloy
Graphite
GFRP
CFRP
Machineable
Ceramics
BALL
DF
30
DC
DCON(h6)
DN
Aluminium Alloy
SQUARE
CARBIDE
APMX
LU
PRFRAD
Type1
LF
3<PRFRAD<6
0.01
h6
0
- 0.008
0
- 0.009
0
- 0.011
a 2 flute ball nose end mill with original diamond coating for graphite machining.
Order Number
PRFRAD
DC
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
DF2MBR0300A100
DF2MBR0300A150
DF2MBR0400A110
DF2MBR0400A150
DF2MBR0500A120
DF2MBR0500A180
DF2MBR0600A130
DF2MBR0600A200
3
3
4
4
5
5
6
6
6
6
8
8
10
10
12
12
30
30
40
40
50
50
55
55
50
50
60
60
70
70
75
75
5.85
5.85
7.85
7.85
9.7
9.7
11.7
11.7
100
150
110
150
120
180
130
200
6
6
8
8
10
10
12
12
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
(Effective Coating Length : 1-1.5DC)

Graphite
Work material
R
Overall Length
PRFRAD (mm) LF (mm)
R3
R4
R5
R6
100
150
110
150
120
180
130
200
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
16000
12000
12000
9200
9500
7300
8000
6100
1900
1200
2000
1400
2200
1500
1800
1200
0.6
0.4
0.8
0.6
1.0
0.8
1.2
1.0
1.5
1.2
2.0
1.6
2.5
2.0
3.0
2.5
16000
12000
12000
9200
9500
7300
8000
6100
1500
960
1600
1100
1800
1200
1400
960
0.6
0.4
0.8
0.6
1.0
0.8
1.2
1.0
1.5
1.2
2.0
1.6
2.5
2.0
3.0
2.5
ae
Depth of cut
ap
J260
Copper Alloy
Graphite
GFRP
CFRP
Machineable
Ceramics
30
DN
Aluminium Alloy
DF
UWC
CARBIDE
B2
DC
Type1
LF
DN
Effective
length
APMX
LU
DCON(h6)
PRFRAD
Effective length
for inclined angle
12
Type2
h6
PRFRAD
0.01
APMX
LU
DCON(h6)
0.1<PRFRAD<3
Inclined angle
BALL
DC
SQUARE
DF2XLB
LF
DCON=4,6
0
- 0.008
LU
DN
B2
LF
DCON
DF2XLBR0010N005
DF2XLBR0015N020
DF2XLBR0015N030
DF2XLBR0020N010
DF2XLBR0020N020
DF2XLBR0020N030
DF2XLBR0020N040
DF2XLBR0020N080
DF2XLBR0020N120
DF2XLBR0025N040
DF2XLBR0025N050
DF2XLBR0025N080
DF2XLBR0030N020
DF2XLBR0030N040
DF2XLBR0030N050
DF2XLBR0030N060
DF2XLBR0030N080
DF2XLBR0030N100
DF2XLBR0030N160
DF2XLBR0040N060
DF2XLBR0040N080
DF2XLBR0050N040
DF2XLBR0050N060
DF2XLBR0050N080
DF2XLBR0050N100
DF2XLBR0050N120
DF2XLBR0050N200
DF2XLBR0050N300
DF2XLBR0050N400
DF2XLBR0075N080
DF2XLBR0075N100
DF2XLBR0075N160
DF2XLBR0075N300
DF2XLBR0100N080
0.1
0.15
0.15
0.2
0.2
0.2
0.2
0.2
0.2
0.25
0.25
0.25
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.75
0.75
0.75
0.75
1
0.2
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
2
0.2
0.3
0.3
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1.2
1.2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2.3
2.3
2.3
2.3
3
0.5
2
3
1
2
3
4
8
12
4
5
8
2
4
5
6
8
10
16
6
8
4
6
8
10
12
20
30
40
8
10
16
30
8
0.18
0.27
0.27
0.36
0.36
0.36
0.36
0.36
0.36
0.46
0.46
0.46
0.56
0.56
0.56
0.56
0.56
0.56
0.56
0.76
0.76
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.9
11.5
9.9
9.1
11
10
9.1
8.4
6.4
5.1
8.3
7.7
6.3
9.9
8.3
7.6
7.1
6.2
5.5
4.1
7
6.1
8
6.8
5.9
5.2
4.6
3.3
2.4
1.9
5.4
4.7
3.4
2.1
4.9
50
50
50
50
50
50
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
80
80
80
60
60
80
80
60
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
0.5
2.1
3.1
1.0
2.0
3.1
4.1
8.3
12.5
4.1
5.2
8.3
2.1
4.2
5.2
6.3
8.3
10.4
16.7
6.3
8.3
4.2
6.3
8.4
10.5
12.6
21.0
31.4
41.8
8.4
10.5
16.8
31.4
8.3
0.5
2.2
3.2
1.0
2.1
3.2
4.3
8.7
13.0
4.3
5.4
8.7
2.2
4.4
5.4
6.5
8.7
10.9
17.4
6.5
8.7
4.4
6.6
8.8
11.0
13.2
21.9
32.8
43.7
8.8
11.0
17.5
32.8
8.7
0.6
2.4
3.6
1.1
2.3
3.5
4.7
9.5
14.3
4.7
5.9
9.5
2.4
4.8
6.0
7.1
9.5
11.9
19.1
7.1
9.5
4.8
7.2
9.6
12.0
14.4
24.0
36.0
0.7
2.6
3.9
1.2
2.6
3.9
5.2
10.5
15.8
5.2
6.5
10.5
2.6
5.2
6.6
7.9
10.6
13.2
21.2
7.9
10.5
5.3
8.0
10.6
13.3
15.9
26.6
9.6
12.0
19.2
35.9
9.4
TAPER
APMX
SOLID END MILLS
DC
Type
PRFRAD
Stock
Order Number
No. of Flutes
Unit : mm
RADIUS
a 2 flute long neck ball nose end mill with Mitsubishi's unique diamond coating for graphite machining.
*
*
10.6
13.2
21.2
10.4
* No interference
J261
DF END MILLS
DF2XLB
APMX
LU
DN
B2
LF
DCON
No. of Flutes
DF2XLBR0100N100
DF2XLBR0100N120
DF2XLBR0100N160
DF2XLBR0100N200
DF2XLBR0100N250
DF2XLBR0100N400
DF2XLBR0100N600
DF2XLBR0150N160
DF2XLBR0150N250
DF2XLBR0150N400
DF2XLBR0150N600
DF2XLBR0200N080
DF2XLBR0200N200
DF2XLBR0200N300
DF2XLBR0200N400
DF2XLBR0200N600
DF2XLBR0300N120
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
2
2
2
2
2
3
2
2
2
2
2
2
2
3
3
3
3
4
4
4
4
4
6
3
3
3
3
3
3
3
4.5
4.5
4.5
4.5
6
6
6
6
6
9
10
12
16
20
25
40
60
16
25
40
60
8
20
30
40
60
12
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.9
2.9
2.9
2.9
3.9
3.9
3.9
3.9
3.9
5.85
4.2
3.7
2.9
2.5
2
1.4
0.9
1.7
1.2
0.7
0.5
60
60
80
80
80
100
100
80
80
100
100
80
80
80
100
100
100
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
J262
Type
DC
Stock
PRFRAD
SOLID END MILLS
Unit : mm
Order Number
TAPER
RADIUS
BALL
SQUARE
CARBIDE
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
10.4
12.5
16.7
20.9
26.1
41.7
62.6
16.7
26.1
41.7
10.9
13.0
17.4
21.8
27.2
43.5
*
*
*
*
*
*
*
11.8 13.0
14.2 15.7
19.0
23.8
*
*
* *
* *
* * *
17.3
* *
27.2
* *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* No interference
CARBIDE

Graphite
R
Neck length
PRFRAD (mm) LU (mm)
R0.1
R0.15
R0.2
R0.25
R0.3
R0.4
R0.5
0.5
2
3
1
2
3
4
8
12
4
5
8
2
4
5
6
8
10
16
6
8
4
6
8
10
12
20
30
40
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
40000
40000
40000
40000
40000
40000
40000
30000
20000
40000
38000
30000
40000
40000
40000
40000
37000
35000
22000
40000
40000
40000
40000
40000
40000
40000
30000
20000
15000
800
1200
1200
1500
1500
1300
1300
800
450
1500
1300
1000
1800
1500
1500
1500
1200
1000
530
1700
1700
2500
2500
2000
2000
2000
1100
600
400
0.01
0.03
0.03
0.05
0.05
0.04
0.04
0.03
0.03
0.05
0.05
0.04
0.07
0.06
0.06
0.06
0.05
0.05
0.04
0.08
0.08
0.12
0.1
0.1
0.1
0.1
0.08
0.06
0.04
0.03
0.08
0.08
0.15
0.12
0.12
0.1
0.1
0.08
0.15
0.15
0.12
0.2
0.18
0.17
0.15
0.15
0.15
0.12
0.2
0.15
0.3
0.3
0.25
0.2
0.2
0.2
0.15
0.12
40000
40000
40000
40000
40000
40000
32000
40000
36000
28000
40000
40000
40000
40000
35000
40000
30000
40000
40000
40000
33000
30000
800
800
600
2000
1300
800
600
800
700
500
1500
1200
1100
1000
800
1500
1200
2000
2000
1800
1400
1000
0.003
0.003
0.002
0.015
0.01
0.005
0.004
0.01
0.008
0.002
0.03
0.02
0.015
0.008
0.005
0.02
0.008
0.05
0.03
0.02
0.01
0.007
0.02
0.03
0.03
0.04
0.04
0.04
0.04
0.05
0.05
0.05
0.06
0.06
0.06
0.06
0.06
0.08
0.08
0.1
0.1
0.1
0.1
0.1
SOLID END MILLS
Work material
ae
Depth of cut
ap
J263
DF END MILLS
CARBIDE
DF2XLB
Graphite
Work material
R
Neck length
PRFRAD (mm) LU (mm)
R0.75
R1
R1.5
SOLID END MILLS
R2
R3
8
10
16
30
8
10
12
16
20
25
40
60
16
25
40
60
8
20
30
40
60
12
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
40000
40000
35000
27000
40000
40000
35000
30000
30000
25000
20000
15000
28000
20000
16000
14000
24000
21000
15000
13000
12000
17000
2800
2800
2000
1000
3000
3000
2500
2000
2000
1500
1000
500
3000
2000
1500
1000
3800
3300
2000
1600
1400
2800
0.15
0.15
0.15
0.1
0.23
0.2
0.2
0.2
0.2
0.18
0.15
0.1
0.3
0.25
0.2
0.17
0.5
0.5
0.4
0.35
0.3
0.6
0.45
0.45
0.3
0.3
0.7
0.6
0.6
0.5
0.5
0.45
0.4
0.3
0.9
0.75
0.6
0.45
1.5
1.5
1.2
1.0
0.9
2.0
40000
32000
20000
40000
40000
35000
30000
20000
20000
28000
20000
16000
24000
21000
15000
13000
12000
17000
2400
1800
900
3000
2800
2300
1800
1200
1000
3000
2000
1500
3800
3300
2000
1600
1400
2800
0.07
0.05
0.03
0.1
0.08
0.08
0.05
0.04
0.03
0.3
0.25
0.2
0.5
0.4
0.3
0.25
0.2
0.6
0.15
0.15
0.15
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.6
ae
Depth of cut
ap
J264
DLC END MILLS
DLC2MB
UWC
Copper Alloy
Aluminium Alloy
Graphite
GFRP
CFRP
DLC
30
CARBIDE
Machineable
Ceramics
Type1
DCON(h6)
DC
PRFRAD
APMX
LF
Type2
0.02
DC < 12
DC>12
APMX
LF
BALL
0.01
0
- 0.020
h6
PRFRAD
PRFRAD<6 PRFRAD>6
DCON(h6)
DC
SQUARE
15
0
- 0.030
4 < DCON < 6 8<DCON<10 12<DCON<16 DCON=20

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
PRFRAD
DC
APMX
LF
DCON
Stock
DLC2MBR0010
DLC2MBR0015
DLC2MBR0020
DLC2MBR0025
DLC2MBR0030
DLC2MBR0040
DLC2MBR0050
DLC2MBR0075
DLC2MBR0100
DLC2MBR0125
DLC2MBR0150
DLC2MBR0200
DLC2MBR0250
DLC2MBR0300
DLC2MBR0400
DLC2MBR0500
DLC2MBR0600
DLC2MBR0800
DLC2MBR1000
0.1
0.15
0.2
0.25
0.3
0.4
0.5
0.75
1
1.25
1.5
2
2.5
3
4
5
6
8
10
0.2
0.3
0.4
0.5
0.6
0.8
1
1.5
2
2.5
3
4
5
6
8
10
12
16
20
0.4
0.6
0.8
1
1.2
1.6
2.5
4
6
6
8
8
12
12
14
18
22
30
38
40
40
40
40
40
40
40
40
60
60
70
70
80
80
90
100
110
140
160
4
4
4
4
4
4
4
4
6
6
6
6
6
6
8
10
12
16
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
TAPER
Order Number
No. of
Flutes
Unit : mm
SOLID END MILLS
ideal for machining non-ferrous materials.
RADIUS
a 2 flute ball nose end mill with new high welding resistance DLC coating,
J265
DLC END MILLS
DLC2MB
CARBIDE

Aluminium cast,
%>15
% < 15
%>15
% < 15
R
PRFRAD
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
R 0.1
R 0.15
R 0.2
R 0.25
R 0.3
R 0.4
R 0.5
R 0.75
R 1
R 1.25
R 1.5
R 2
R 2.5
R 3
R 4
R 5
R 6
R 8
R10
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
30000
24000
20000
15000
12000
10000
7500
6000
350
480
600
800
1000
1500
2000
2200
2800
3200
4000
4200
4400
4000
3600
3600
3200
2800
2500
40000
40000
40000
40000
40000
40000
40000
40000
40000
38000
32000
24000
19000
16000
12000
9500
8000
6000
4800
260
360
450
600
750
1100
1500
1600
2200
2200
2600
2800
2800
2800
2400
2000
2200
1800
1600
40000
40000
40000
40000
40000
40000
40000
40000
40000
32000
32000
24000
19000
16000
12000
9600
8000
6000
4800
280
380
480
640
800
1200
1600
1800
2200
2000
2600
2700
2800
2600
2300
2300
2000
1800
1600
40000
40000
40000
40000
40000
40000
40000
40000
32000
30000
26000
19000
15000
13000
9600
7600
6400
4800
3800
210
290
360
480
600
880
1200
1300
1400
1400
1700
1800
1800
1800
1500
1300
1400
1200
1000
End mill
PRFRAD
(PRFRAD< 0.5)
< 0.4PRFRAD (PRFRAD> 0.5)
SOLID END MILLS
< 0.2PRFRAD
J266
Depth of
cut
%
< 0.2PRFRAD
PRFRAD:Radius
1)
2)
3)
4)
ap
Aluminium alloy
Work
material
pf
% is the inclination angle of the machined surface.

When cutting a very hard workpiece, reduce the feed rate.
CBN END MILLS
CBN2XLB
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
B2
DC
DN
Hardened Steel
( < 55HRC)
CBN
15
LF
R
h5
Effective
length
Effective length
for inclined angle
0.2<PRFRAD<1
BALL
LU
APMX
DCON(h5)
Type1
PRFRAD
SQUARE
(<30HRC)
( < 45HRC)
CBN
0.005
Inclined angle
4 < DCON < 6

0
- 0.005
LU
DN
B2
LF
DCON
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.75
0.75
0.75
0.75
1
1
1
1
1
0.4
0.4
0.4
0.4
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1.5
1.5
1.5
1.5
2
2
2
2
2
0.3
0.3
0.3
0.3
0.4
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
1.1
1.1
1.1
1.1
1.2
1.5
1.5
1.5
1.5
1
1
1.6
1.6
0.9
1.5
1.5
2.4
2.4
1
2
2
3.2
3.2
1.1
2.5
2.5
4
4
3.8
3.8
6
6
1.7
5
5
8
8
0.36
0.36
0.36
0.36
0.56
0.56
0.56
0.56
0.56
0.76
0.76
0.76
0.76
0.76
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.9
1.9
1.9
1.9
1.9
13.4
13.9
12.4
13.3
14.1
12.6
13.4
11.3
12.5
14.1
11.8
12.9
10.3
11.7
14.1
11
12.3
9.3
11
9.1
11
7.1
9.3
13.6
7.3
9.8
5.3
7.9
51
51
51
51
62
51
51
51
51
62
51
51
51
51
62
51
51
51
51
52
52
52
52
62
52
52
52
52
4
6
4
6
6
4
6
4
6
6
4
6
4
6
6
4
6
4
6
4
6
4
6
6
4
6
4
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
1
1
1.6
1.6
0.9
1.5
1.5
2.5
2.5
1
2
2
3.3
3.3
1.1
2.6
2.6
4.1
4.1
3.9
3.9
6.2
6.2
1.7
5.1
5.1
8.2
8.2
1
1
1.7
1.7
0.9
1.6
1.6
2.6
2.6
1
2.1
2.1
3.4
3.4
1.1
2.7
2.7
4.3
4.3
4.1
4.1
6.4
6.4
1.7
5.3
5.3
8.5
8.5
1.1
1.1
1.8
1.8
1
1.7
1.7
2.7
2.7
1.1
2.3
2.3
3.6
3.6
1.2
2.8
2.8
4.6
4.6
4.3
4.3
6.8
6.8
1.8
5.6
5.6
9
9
1.2
1.2
2
2
1.1
1.8
1.8
2.9
2.9
1.2
2.4
2.4
3.9
3.9
1.2
3
3
4.9
4.9
4.6
4.6
7.3
7.3
1.9
6
6
9.7
9.7
TAPER
APMX
SOLID END MILLS
DC
Type
CBN2XLBR0020N010S04
CBN2XLBR0020N010S06
CBN2XLBR0020N016S04
CBN2XLBR0020N016S06
CBN2XLBR0030N009S06
CBN2XLBR0030N015S04
CBN2XLBR0030N015S06
CBN2XLBR0030N024S04
CBN2XLBR0030N024S06
CBN2XLBR0040N010S06
CBN2XLBR0040N020S04
CBN2XLBR0040N020S06
CBN2XLBR0040N032S04
CBN2XLBR0040N032S06
CBN2XLBR0050N011S06
CBN2XLBR0050N025S04
CBN2XLBR0050N025S06
CBN2XLBR0050N040S04
CBN2XLBR0050N040S06
CBN2XLBR0075N038S04
CBN2XLBR0075N038S06
CBN2XLBR0075N060S04
CBN2XLBR0075N060S06
CBN2XLBR0100N017S06
CBN2XLBR0100N050S04
CBN2XLBR0100N050S06
CBN2XLBR0100N080S04
CBN2XLBR0100N080S06
PRFRAD
Stock
Order Number
No. of Flutes
Unit : mm
RADIUS
a Solid CBN ball nose. A wide variation of neck lengths available.
Designed with short cutting edge and neck lengths for high rigidity.
J267
CBN END MILLS

CBN
CBN2XLB
Work
material
AISI H13
AISI D2
AISI W1, AISI M2
R
Revolution
(min-1)
PRFRAD (mm)
R0.2
R0.3
R0.4
R0.5
R0.75
R1
Depth of
cut
50000
50000
50000
50000
50000
50000

(mm/min)
ap (mm)
ae (mm)
(min-1)
1500
2000
3000
3000
3500
4000
0.006
0.01
0.02
0.03
0.04
0.05
0.01
0.02
0.05
0.06
0.08
0.1
50000
50000
50000
50000
50000
50000

(mm/min)
ap (mm)
ae (mm)
(min-1)
1200
1500
2000
2000
2500
3000
0.006
0.01
0.02
0.03
0.03
0.04
0.01
0.02
0.04
0.05
0.06
0.07
50000
50000
50000
50000
50000
50000

(mm/min)
ap (mm)
ae (mm)
1200
1500
2000
2000
2500
3000
0.004
0.008
0.015
0.02
0.02
0.03
0.008
0.015
0.03
0.03
0.04
0.05
ae (MAX.)
ap (MAX.)
SOLID END MILLS
2) Oil mist coolant is recommended.
J268
CARBIDE END MILLS
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
APMX
0.01
0.02
DC < 12
DC>12
0
- 0.020
h6
0
- 0.030
PRFRAD
4 < DCON < 6 8<DCON<10 12<DCON<16

0
- 0.008
0
- 0.009
APMX
APMX
Type2
Type3
LF
DC
PRFRAD
Type1
LF
DC
PRFRAD
BALL
Austenitic
Stainless Steel
DCON(h6)
Hardened Steel
(>55HRC)
CARBIDE
DCON(h6)
Hardened Steel
( < 55HRC)
30
DCON(h6)
(<30HRC)
( < 45HRC)
UWC
SQUARE
C2MB
LF
0
- 0.011
DC
APMX
LF
DCON
Stock
C2MBR0050
C2MBR0075
C2MBR0100
C2MBR0150
C2MBR0200
C2MBR0250
C2MBR0300
C2MBR0400
C2MBR0500
C2MBR0550
C2MBR0650
C2MBR0700
C2MBR0750
0.5
0.75
1
1.5
2
2.5
3
4
5
5.5
6.5
7
7.5
1
1.5
2
3
4
5
6
8
10
11
13
14
15
2.5
4
6
8
8
12
12
14
18
22
26
26
30
40
40
60
70
70
80
80
90
100
110
120
120
140
4
4
6
6
6
6
6
8
10
12
12
12
16
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
2
2
2
1
3
3
1
TAPER
PRFRAD
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute ultra micro-grain carbide end mill for contour milling of alloy and hardened steels.
J269
CARBIDE END MILLS

CARBIDE
C2MB
Roughing (Large depth of cut < 0.8R)
Work
material
Carbon steel,
Carbon steel, Alloy steel ( 30HRC)

Pre-hardened steel (3045HRC)
Alloy steel, Tool steel, Pre-hardened steel

(30 45HRC)
AISI 1055, AISI P20
AISI H13, AISI P21
AISI H13, AISI D2, AISI P21
R
Revolution
PRFRAD
(min-1)
(mm)
R 0.5
R 1
R 2
R 3
R 4
R 5
R 6
R 8
R10
Finishing (Depth of cut 0.05R)
4100
2600
1900
1400
1100
940
700
560
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
70
120
150
160
140
130
100
80
2800
1650
1200
900
710
600
450
360
40
85
95
105
95
85
60
50
AISI 1055, AISI P20

%>15
% < 15
%>15
% < 15
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
14000
10500
7200
5200
4000
3200
2600
1900
1500
180
350
500
560
640
700
640
620
590
10000
7300
5100
3600
2700
2200
1750
1300
1000
120
210
300
350
380
380
350
330
310
12000
8400
5900
4200
3100
2500
2100
1550
1250
150
220
360
410
440
460
430
430
410
7000
5500
4300
2900
2200
1750
1450
1100
860
80
130
210
240
240
250
250
250
250

2) Cutting conditions may differ considerably due to the overhang (milling depth and neck length), depth of cut, and machine tool conditions.
Please see the above table as a standard starting point.
feed rate proportionately. Please reduce the feed rate when the surface finish is important.
End mill
J270
pf
ap
SOLID END MILLS
PRFRAD
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
30
Copper Alloy
BHTA
CARBIDE
Aluminium Alloy
B2
DC
DN
VF
UWC
LF
Effective length
for inclined angle
0.4<PRFRAD<2.5
0.01
0.8 < DC < 5

0
- 0.02
h6
4 < DCON < 6 DCON=8

0
- 0.008
BALL
LU_2
Effective
length
LU
DCON(h6)
PRFRAD
Type1
20
APMX
SQUARE
VF3XB
Inclined angle
0
- 0.009
0.4
0.4
0.4
0.9
0.9
0.9
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1.5
1.5
1.5
1.5
1.5
1.5
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.3
1.3
1.3
6
8
12
8
12
16
8
10
12
16
20
25
30
35
8
12
16
20
25
30
35
40
50
60
70
12
16
20
25
30
35
10
15
20
1.5
1.5
1.5
1.5
1.5
1.5
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.3
2.8
2.8
2.8
LF DCON
0.82
0.85
0.91
0.96
1.09
1.22
1.02
1.05
1.08
1.13
1.19
1.26
1.33
1.40
1.12
1.24
1.37
1.50
1.65
1.81
1.97
2.12
2.44
2.75
3.07
1.45
1.66
1.87
2.13
2.39
2.65
1.54
1.61
1.68
8.9 60
7.5 60
5.7 60
7.6 60
5.8 60
4.7 60
9.6 60
8.5 60
7.6 60
6.3 70
5.4 70
4.6 70
4.0 80
3.5 80
9.7 60
7.7 60
6.4 70
5.5 70
4.7 70
4.0 80
3.6 80
3.2 80
2.7 110
2.3 110
2.0 110
7.9 60
6.5 70
5.6 70
4.8 70
4.1 80
3.7 80
8.1 60
6.2 60
5.0 70
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30' 1
6.3 6.6 6.9 7.3

8.4 8.6 9.1 9.5
12.4 12.7 13.4 14.1
8.4 8.9 9.3
12.4 13.1 13.8
16.5 17.3 18.3
8.5 8.8 9.3 9.8
10.5 10.9 11.4 12.1
12.6 13.0 13.6 14.4
16.6 17.1 18.0 18.9
20.6 21.2 22.3 23.5
25.7 26.3 27.7 29.3
30.7 31.5 33.1 35.0
35.7 36.6 38.6 40.7
8.6 9.1 9.6
12.6 13.3 14.1
16.7 17.6 18.5
20.7 21.8 23.0
25.7 27.1 28.6
30.8 32.4 34.2
35.8 37.7 39.8
40.8 43.0 45.4
50.9 53.6
60.9 64.1
71.0 74.7
13.0 13.7
17.1 18.0
21.2 22.4
26.3 27.8
31.5 33.2
36.6 38.6
10.6 10.9 11.4 12.0
15.6 16.0 16.9 17.8
20.6 21.2 22.3 23.5
TAPER
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
B2
SOLID END MILLS
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.75
0.75
0.75
DN
Type
VF3XBR0040T0024L006
VF3XBR0040T0024L008
VF3XBR0040T0024L012
VF3XBR0040T0054L008
VF3XBR0040T0054L012
VF3XBR0040T0054L016
VF3XBR0050T0024L008
VF3XBR0050T0024L010
VF3XBR0050T0024L012
VF3XBR0050T0024L016
VF3XBR0050T0024L020
VF3XBR0050T0024L025
VF3XBR0050T0024L030
VF3XBR0050T0024L035
VF3XBR0050T0054L008
VF3XBR0050T0054L012
VF3XBR0050T0054L016
VF3XBR0050T0054L020
VF3XBR0050T0054L025
VF3XBR0050T0054L030
VF3XBR0050T0054L035
VF3XBR0050T0054L040
VF3XBR0050T0054L050
VF3XBR0050T0054L060
VF3XBR0050T0054L070
VF3XBR0050T0130L012
VF3XBR0050T0130L016
VF3XBR0050T0130L020
VF3XBR0050T0130L025
VF3XBR0050T0130L030
VF3XBR0050T0130L035
VF3XBR0075T0024L010
VF3XBR0075T0024L015
VF3XBR0075T0024L020
PRFRAD DC BHTA APMX LU_2 LU
Stock
Order Number
No. of Flutes
Unit : mm
RADIUS
a 3 flute ball end mill, high rigidity taper neck type.
*
*
*
* No interference
a
J271
VF3XB
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.25
1.25
1.25
1.25
1.25
1.25
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
5
0.4
0.9
0.9
0.9
0.9
1.5
1.5
1.5
0.4
0.4
0.4
0.4
0.4
0.4
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1.5
1.5
1.5
1.5
0.9
0.9
0.9
1.5
1.5
1.5
0.4
0.4
0.4
0.4
0.4
0.9
0.9
0.9
0.9
0.9
0.9
1.5
1.5
1.5
1.5
0.9
0.9
0.9
0.9
0.9
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3.5
30
15
20
30
40
15
20
30
16
20
25
30
35
40
20
25
30
35
40
50
60
70
25
30
35
40
20
30
40
20
30
40
20
25
30
40
50
20
30
40
50
60
70
40
50
60
70
30
40
50
60
35
2.8
2.8
2.8
2.8
2.8
2.8
2.8
2.8
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
4.5
4.5
4.5
4.5
4.5
4.5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6.5
DN
B2
1.82
1.82
1.98
2.29
2.61
2.08
2.34
2.86
2.07
2.13
2.20
2.27
2.34
2.41
2.42
2.57
2.73
2.89
3.04
3.36
3.67
3.99
3.02
3.28
3.54
3.81
2.89
3.20
3.52
3.21
3.74
4.26
3.11
3.18
3.25
3.39
3.53
3.37
3.69
4.00
4.31
4.63
4.94
4.73
5.26
5.78
6.30
4.65
4.97
5.28
5.60
5.80
3.7
6.3
5.1
3.7
3.0
6.4
5.2
3.8
5.5
4.6
3.9
3.4
2.9
2.6
4.7
4.0
3.4
3.0
2.7
2.2
1.9
1.6
4.1
3.5
3.1
2.7
4.3
3.1
2.4
4.4
3.1
2.5
3.8
3.1
2.7
2.1
1.7
3.8
2.7
2.1
1.7
2.3
2.0
2.2
2.8
2.4
2.1
3.5
2.7
2.2
1.9
2.4
LF DCON
80
60
70
80
80
60
70
80
70
70
70
80
80
80
70
70
80
80
80
110
110
110
70
80
80
80
60
80
80
60
80
80
60
80
80
80
100
60
80
80
100
110
120
80
110
110
120
90
90
110
110
90
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
6
8
8
8
8
8
8
8
8
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
Type
VF3XBR0075T0024L030
VF3XBR0075T0054L015
VF3XBR0075T0054L020
VF3XBR0075T0054L030
VF3XBR0075T0054L040
VF3XBR0075T0130L015
VF3XBR0075T0130L020
VF3XBR0075T0130L030
VF3XBR0100T0024L016
VF3XBR0100T0024L020
VF3XBR0100T0024L025
VF3XBR0100T0024L030
VF3XBR0100T0024L035
VF3XBR0100T0024L040
VF3XBR0100T0054L020
VF3XBR0100T0054L025
VF3XBR0100T0054L030
VF3XBR0100T0054L035
VF3XBR0100T0054L040
VF3XBR0100T0054L050
VF3XBR0100T0054L060
VF3XBR0100T0054L070
VF3XBR0100T0130L025
VF3XBR0100T0130L030
VF3XBR0100T0130L035
VF3XBR0100T0130L040
VF3XBR0125T0054L020
VF3XBR0125T0054L030
VF3XBR0125T0054L040
VF3XBR0125T0130L020
VF3XBR0125T0130L030
VF3XBR0125T0130L040
VF3XBR0150T0024L020
VF3XBR0150T0024L025
VF3XBR0150T0024L030
VF3XBR0150T0024L040
VF3XBR0150T0024L050
VF3XBR0150T0054L020
VF3XBR0150T0054L030
VF3XBR0150T0054L040
VF3XBR0150T0054L050
VF3XBR0150T0054L060
VF3XBR0150T0054L070
VF3XBR0150T0130L040
VF3XBR0150T0130L050
VF3XBR0150T0130L060
VF3XBR0150T0130L070
VF3XBR0200T0054L030
VF3XBR0200T0054L040
VF3XBR0200T0054L050
VF3XBR0200T0054L060
VF3XBR0250T0054L035
Stock
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
Order Number
Unit : mm
No. of Flutes
CARBIDE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30' 1
J272
*
*
*
*
* *
* *
*
*
*
*
*
* *
*
*
* *
*
*
*
*
*
*
*
a
30.7 31.5 33.1 35.0

15.7 16.5 17.4
20.7 21.8 23.0
30.8 32.4 34.2
40.8 43.0 45.3
16.1 17.0
21.2 22.4
31.5 33.2
16.7 17.1 18.0 19.0
20.7 21.3 22.3 23.5
25.8 26.4 27.8 29.3
30.8 31.6 33.2 35.0
35.8 36.7 38.6
40.8 41.9 44.0
20.8 21.9 23.0
25.8 27.2 28.6
30.9 32.5 34.2
35.9 37.7 39.8
40.9 43.0
51.0 53.6
61.0
71.1
26.4 27.9
31.6 33.3
36.7 38.7
41.8
20.8 21.9 23.1
30.9 32.5 34.2
40.9 43.1
21.4 22.5
31.6 33.3
41.9
20.7 21.3 22.3 23.5
25.8 26.4 27.7 29.2
30.8 31.6 33.2
40.9 41.9 44.0
50.9 52.2
20.9 21.9 23.0
30.9 32.5
41.0 43.1
51.0
61.1 64.2
71.1 74.8
41.9
52.2
62.4
72.7
30.9 32.5 34.2
41.0 43.0
51.0 53.6
61.1
35.9 37.7
*
*
* *
*
No interference
CARBIDE
6.5 5.95 2.2 90

6.5 6.27 1.8 110
6.5 6.58 1.5 110
8
8
8
3
3
3
1
1
1
a
a
30' 1
*
* *
* *
No interference
41.0 43.0
51.0
61.1
SQUARE
40
50
60
BALL
3.5
3.5
3.5
Effective length
for inclined angle
RADIUS
0.9
0.9
0.9
LF DCON
TAPER
5
5
5
B2
SOLID END MILLS
2.5
2.5
2.5
DN
Type
VF3XBR0250T0054L040
VF3XBR0250T0054L050
VF3XBR0250T0054L060
Stock
Order Number
No. of Flutes
Unit : mm
J273

CARBIDE
VF3XB

Pre-hardened steel
Hardened steel (45 55HRC) Hardened steel (55 62HRC)

AISI P20

AISI P21
AISI H13
Work material
AISI D2
Neck
Taper angle
R
Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut
length
one side
-1
-1
-1
-1
PRFRAD (mm)
LU_2 (mm) (min ) (mm/min) ap (mm) (min ) (mm/min) ap (mm) (min ) (mm/min) ap (mm) (min ) (mm/min) ap (mm)
BHTA
0.4
R0.4
0.9
0.4
R0.5
SOLID END MILLS
0.9
1.5
0.4
R0.75
0.9
1.5
6
8
12
8
12
16
8
10
12
16
20
25
30
35
8
12
16
20
25
30
35
40
50
60
70
12
16
20
25
30
35
10
15
20
30
15
20
30
40
15
20
30
34000
31000
28000
31000
28000
25000
27000
24000
24000
22000
20000
18000
15000
14000
27000
24000
22000
20000
18000
15000
14000
11000
8400
7000
7000
24000
22000
20000
18000
15000
14000
18000
17000
17000
14000
17000
17000
14000
13000
17000
17000
14000
2700
2100
2000
2200
2100
1100
2700
2200
2200
2100
1400
1300
960
800
2900
2400
2200
1600
1400
1100
960
800
610
510
480
2600
2400
1800
1600
1300
1100
2700
2200
2100
1600
2400
2200
1800
1300
2600
2400
2000
0.03
0.02
0.015
0.02
0.015
0.01
0.04
0.03
0.03
0.03
0.015
0.015
0.01
0.008
0.04
0.03
0.03
0.015
0.015
0.01
0.008
0.007
0.006
0.004
0.003
0.03
0.03
0.015
0.015
0.01
0.008
0.06
0.04
0.03
0.015
0.04
0.03
0.015
0.01
0.04
0.03
0.015
31000
29000
26000
29000
26000
23000
25000
22000
22000
21000
18000
17000
14000
13000
25000
22000
21000
18000
17000
14000
13000
11000
7800
6500
6500
22000
21000
18000
17000
14000
13000
17000
16000
16000
13000
16000
16000
13000
12000
16000
16000
13000
2200
1700
1600
1800
1700
910
2200
1800
1800
1700
1200
1000
780
650
2300
2000
1800
1300
1200
910
780
650
490
400
390
2100
2000
1400
1300
1000
910
2200
1800
1700
1300
2000
1800
1400
1000
2100
2000
1600
<0.1PRFRAD
Depth of cut
<0.2PRFRAD
0.025
0.02
0.01
0.02
0.01
0.01
0.04
0.025
0.025
0.025
0.01
0.01
0.01
0.007
0.04
0.025
0.025
0.01
0.01
0.009
0.007
0.006
0.005
0.004
0.002
0.025
0.025
0.01
0.01
0.01
0.007
0.05
0.04
0.025
0.01
0.04
0.025
0.01
0.01
0.04
0.025
0.01
24000
22000
20000
22000
20000
18000
19000
17000
17000
16000
14000
13000
11000
10000
19000
17000
16000
14000
13000
11000
10000
8000
6000
5000
5000
17000
16000
14000
13000
11000
10000
13000
12000
12000
10000
12000
12000
10000
9000
12000
12000
10000
1700
1300
1200
1400
1300
700
1700
1400
1400
1300
900
800
600
500
1800
1500
1400
1000
900
700
600
500
380
320
300
1600
1500
1100
1000
800
700
1700
1400
1300
1000
1500
1400
1100
800
1600
1500
1200
0.02
0.015
0.01
0.015
0.01
0.008
0.03
0.02
0.02
0.02
0.01
0.009
0.008
0.006
0.03
0.02
0.02
0.01
0.009
0.008
0.006
0.005
0.004
0.003
0.002
0.02
0.02
0.01
0.009
0.008
0.006
0.04
0.03
0.02
0.01
0.03
0.02
0.01
0.008
0.03
0.02
0.01
19000
18000
16000
18000
16000
14000
15000
14000
14000
13000
11000
10000
8800
8000
15000
14000
13000
11000
10000
8800
8000
6400
4800
4000
4000
14000
13000
11000
11000
8800
8000
10000
9600
9600
8000
9600
9600
8000
7200
9600
9600
8000
1400
1000
960
1100
1000
560
1400
1100
1100
1000
720
640
480
400
1400
1200
1100
800
720
560
480
400
300
260
240
1300
1200
880
800
640
560
1400
1100
1000
800
1200
1100
880
640
1300
1200
960
0.015
0.01
0.007
0.01
0.007
0.006
0.02
0.015
0.015
0.015
0.007
0.006
0.006
0.004
0.02
0.015
0.015
0.007
0.006
0.006
0.004
0.003
0.003
0.002
0.001
0.015
0.015
0.007
0.006
0.006
0.004
0.03
0.02
0.015
0.007
0.02
0.015
0.007
0.006
0.02
0.015
0.007
(PRFRAD<1)
(PRFRAD>1)
ap
PRFRAD:Radius
J274
CARBIDE


Pre-hardened steel
Hardened steel (45 55HRC) Hardened steel (55 62HRC)

AISI P20

AISI P21
AISI H13
Work material
AISI D2
0.4
R1
0.9
1.5
0.9
R1.25
1.5
0.4
R1.5
0.9
1.5
R2
0.9
R2.5
0.9
16
20
25
30
35
40
20
25
30
35
40
50
60
70
25
30
35
40
20
30
40
20
30
40
20
30
40
50
20
30
40
50
60
70
50
60
70
30
40
50
60
35
40
60
15000
14000
14000
13000
13000
12000
14000
14000
13000
13000
12000
11000
9800
8400
14000
12600
13000
12000
13000
12000
11000
13000
12000
11000
12000
11000
11000
11000
12000
11000
11000
11000
9800
9800
11000
9800
9800
10000
9500
9500
9000
8000
8000
7600
3200
2400
2100
1800
1600
1400
2600
2200
1900
1800
1600
1400
1100
960
2400
2100
1900
1800
2900
2600
2200
3000
2700
2400
3700
2900
2400
2000
3800
3000
2600
2100
2000
1800
2200
2100
2000
3200
2400
2100
1900
3500
3200
2400
0.07
0.06
0.04
0.03
0.03
0.015
0.06
0.05
0.04
0.04
0.03
0.015
0.007
0.004
0.05
0.04
0.04
0.03
0.06
0.05
0.04
0.06
0.05
0.04
0.13
0.07
0.06
0.04
0.13
0.07
0.06
0.04
0.03
0.015
0.04
0.03
0.015
0.3
0.15
0.1
0.07
0.3
0.2
0.15
14000
13000
13000
12000
12000
11000
13000
13000
12000
12000
11000
10000
9100
7800
13000
12000
12000
11000
12000
11000
9800
12000
11050
9800
11000
10000
10000
9800
11000
10000
10000
9800
9100
9100
9800
9100
9100
9400
8800
8800
8300
7400
7400
7000
2600
2000
1700
1400
1300
1200
2100
1800
1600
1400
1300
1200
910
780
2000
1700
1600
1400
2300
2100
1800
2500
2200
2000
3000
2300
2000
1600
3100
2500
2100
1700
1600
1400
1800
1700
1600
2600
2000
1700
1600
2900
2600
2000
<0.1PRFRAD
<0.2PRFRAD
0.06
0.05
0.04
0.03
0.025
0.01
0.05
0.04
0.04
0.03
0.025
0.01
0.006
0.004
0.04
0.04
0.03
0.025
0.05
0.04
0.04
0.05
0.04
0.04
0.1
0.06
0.05
0.04
0.1
0.06
0.05
0.04
0.025
0.01
0.04
0.025
0.01
0.25
0.12
0.1
0.06
0.25
0.18
0.12
11000
10000
10000
9000
9000
8500
10000
10000
9000
9000
8500
8000
7000
6000
10000
9000
9000
8500
9000
8500
7500
9000
8500
7500
8500
8000
8000
7500
8500
8000
8000
7500
7000
7000
7500
7000
7000
7200
6800
6800
6400
5700
5700
5400
2000
1500
1300
1100
1000
900
1600
1400
1200
1100
1000
900
700
600
1500
1300
1200
1100
1800
1600
1400
1900
1700
1500
2300
1800
1500
1200
2400
1900
1600
1300
1200
1100
1400
1300
1200
2000
1500
1300
1200
2200
2000
1500
0.05
0.04
0.03
0.025
0.02
0.01
0.04
0.03
0.03
0.025
0.02
0.01
0.005
0.003
0.03
0.03
0.025
0.02
0.04
0.03
0.03
0.04
0.03
0.03
0.09
0.05
0.04
0.03
0.09
0.05
0.04
0.03
0.02
0.01
0.03
0.02
0.01
0.2
0.1
0.08
0.05
0.2
0.15
0.1
8800
8000
8000
7200
7200
6800
8000
8000
7200
7200
6800
6400
5600
4800
8000
7200
7200
6800
7200
6800
6000
7200
6800
6000
6800
6400
6400
6000
6800
6400
6400
6000
5600
5600
6000
5600
5600
5800
5400
5400
5100
4600
4600
4300
1600
1200
1000
880
800
720
1300
1100
960
880
800
720
560
480
1200
1000
960
880
1400
1300
1100
1500
1400
1200
1800
1400
1200
960
1900
1500
1300
1000
960
880
1100
1000
960
1600
1200
1000
960
1800
1600
1200
0.03
0.03
0.02
0.02
0.015
0.007
0.03
0.025
0.02
0.02
0.015
0.007
0.003
0.002
0.025
0.02
0.02
0.015
0.03
0.025
0.02
0.03
0.025
0.02
0.06
0.03
0.03
0.02
0.06
0.03
0.03
0.02
0.015
0.007
0.02
0.015
0.007
0.15
0.07
0.06
0.03
0.15
0.1
0.07
SOLID END MILLS
Neck
Taper angle
R
Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut Revolution Feed rate Depth of cut
length
one side
-1
-1
-1
-1
PRFRAD (mm)
LU_2 (mm) (min ) (mm/min) ap (mm) (min ) (mm/min) ap (mm) (min ) (mm/min) ap (mm) (min ) (mm/min) ap (mm)
BHTA
(PRFRAD<1)
(PRFRAD>1)
Depth of cut
ap
PRFRAD:Radius
J275
MIRACLE END MILLS

CARBIDE
VC3MB
(<30HRC)
( < 45HRC)
UWC
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
VC
30
Copper Alloy
Aluminium Alloy
Type1
PRFRAD
DCON(h6)
DC
SQUARE
15
APMX
PRFRAD<6 PRFRAD<8
0.01
0.02
DC < 12
DC>12
0
- 0.020
h6
PRFRAD
Type2
APMX
DCON(h6)
BALL
DC
LF
LF
0
- 0.030

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
a 3 flute ball nose end mill for efficient machining.
J276
Order Number
PRFRAD
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VC3MBR0100
VC3MBR0150
VC3MBR0200
VC3MBR0250
VC3MBR0300
VC3MBR0400
VC3MBR0500
VC3MBR0600
VC3MBR0800
VC3MBR1000
1
1.5
2
2.5
3
4
5
6
8
10
2
3
4
5
6
8
10
12
16
20
6
8
8
12
12
14
18
22
30
38
60
70
70
80
80
90
100
110
140
160
6
6
6
6
6
8
10
12
16
20
3
3
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
2
2
2
2
2
2
CARBIDE

y Roughing

material
AISI H13
%>15
% < 15
%>15
% < 15
R
PRFRAD
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
R 1
R 2
R 3
R 4
R 5
R 6
R 8
R10
32000
18500
13000
10000
8000
6600
5000
4000
3000
3700
4000
5000
5000
4600
4000
3600
25000
14500
10000
8000
6500
5300
4000
3200
1170
1460
1500
2000
2000
1800
1600
1440
18000
11000
7700
6000
4800
4000
3000
2400
1440
1760
1920
2300
2200
2100
1700
1400
16000
9200
6400
4800
3800
3200
2400
1900
640
740
800
920
870
840
680
550
< 0.5PRFRAD
Depth of
cut
< 0.2PRFRAD
PRFRAD:Radius
y Finishing

material
AISI H13
%>15
% < 15
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
R 1
R 2
R 3
R 4
R 5
R 6
R 8
R10
32000
25500
20000
15000
12000
10000
7500
6000
3200
5000
6100
7500
7500
7000
6000
5400
32000
20000
15000
11000
9000
7500
5600
4500
1500
2000
2200
2700
2700
2500
2200
2000
25000
17000
13000
10000
8000
6600
5000
4000
2000
2700
3200
3800
3700
3500
2800
2300
20000
13000
10000
7500
6000
5000
3700
3000
800
1000
1200
1400
1400
1300
1000
900
SOLID END MILLS
%>15
% < 15
R
PRFRAD
(mm)
End mill
PRFRAD
Depth of
cut
%
< 0.06PRFRAD
PRFRAD:Radius
ap
< 0.1PRFRAD
pf

J277
DF END MILLS
DF3XB
Aluminium Alloy
Copper Alloy
Graphite
GFRP
CFRP
Machineable
Ceramics
DF
UWC
30
B2
BHTA
DC
SQUARE
DN
APMX
PRFRAD
DCON(h6)
CARBIDE
20
LU
LU_2
LF
0.5<PRFRAD<2
0.01
Inclined angle
DCON=6
h6
Effective
length
BALL
Effective length
for inclined angle
0
- 0.008
aBall nose taper end mill with Mitsubishi's unique diamond coating for graphite machining.
SOLID END MILLS
TAPER
DF3XBR0050L030
DF3XBR0050L040
DF3XBR0050L050
DF3XBR0100L040
DF3XBR0100L060
DF3XBR0100L080
DF3XBR0150L060
DF3XBR0150L080
DF3XBR0200L100
0.5
0.5
0.5
1
1
1
1.5
1.5
2
1
1
1
2
2
2
3
3
4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
1.5
1.5
1.5
3
3
3
4.5
4.5
6
30
40
50
40
60
80
60
80
100
3
3
3
5
5
5
7.5
7.5
9
B2
DN
LF DCON
4.0
3.2
2.6
2.6
1.8
1.4
1.4
1.1
0.6
1.42
1.60
1.77
2.52
2.86
3.21
3.82
4.17
5.49
100
100
100
100
130
130
130
130
160
3
3
3
3
3
3
3
3
3
6
6
6
6
6
6
6
6
6
a
a
a
a
a
a
a
a
a
Type
Stock
Order Number
No. of Flutes
RADIUS
Unit : mm
Effective length
for inclined angle
30' 1
1 30.4 32.1
1 40.4 41.4
1 50.4 51.7
1 40.7 41.7
1 60.7 62.2
1 80.7 82.7
1 60.8 62.2
1 80.8 82.8
1 100.8
*
*
*
*
* *
R
Neck length
PRFRAD (mm) LU_2 (mm)
R0.5
R1
R1.5
R2
30
40
50
40
60
80
60
80
100
Graphite
Revolution
(min-1)
20000
15000
12000
20000
15000
12000
14000
12000
10000
Feed rate
(mm/min)
1100
750
500
1800
900
600
1700
1200
1100
*
*
*
*
*
*
*
* No interference

Work material
32.8 34.6
43.6 46.0
54.4
43.9
Depth of cut
ap (mm)
0.05
0.04
0.03
0.13
0.09
0.07
0.15
0.12
0.20
Depth of cut
ae (mm)
0.13
0.11
0.10
0.40
0.27
0.20
0.45
0.35
0.50
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
16000
12000
9600
16000
12000
9600
11000
9600
8000
700
480
320
1100
580
380
1100
770
700
0.04
0.03
0.02
0.10
0.07
0.06
0.12
0.10
0.16
0.13
0.11
0.10
0.40
0.27
0.20
0.45
0.35
0.50
ae
Depth of cut
ap
PRFRAD:Radius
a
J278
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
45
Copper Alloy
CARBIDE
Aluminium Alloy
12
DN
PRFRAD
0.02
DC>12
0
- 0.02
h6
PRFRAD
0
- 0.03
Type2
APMX
LU
LF

0
- 0.008
0
- 0.009
0
- 0.011
DCON(h6)
0.01
DC < 12
DN
PRFRAD<6 PRFRAD>6
LF
DC
APMX
LU
DCON(h6)
DC
Type1
BALL
Hardened Steel
( < 55HRC)
VF
UWC
SQUARE
VF4SVB
0
- 0.013
DC
APMX
LU
DN
LF
DCON
Stock
Type
VF4SVBR0100
VF4SVBR0150
VF4SVBR0200
VF4SVBR0250
VF4SVBR0300
VF4SVBR0400
VF4SVBR0500
VF4SVBR0600
VF4SVBR0800
VF4SVBR1000
1
1.5
2
2.5
3
4
5
6
8
10
2
3
4
5
6
8
10
12
16
20
3
4.5
6
7.5
9
12
15
18
24
30
5
7.5
10
12.5
15
20
25
30
40
50
1.9
2.9
3.9
4.9
5.85
7.85
9.7
11.7
15.5
19.5
50
50
50
50
50
60
70
75
90
100
6
6
6
6
6
8
10
12
16
20
4
4
4
4
4
4
4
4
4
4
1
1
1
1
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
TAPER
PRFRAD
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a Impact Miracle ball nose end mill with variable curve ensures stable machining of difficult-to-cut materials.
J279
CARBIDE
VF4SVB
Work
material

Pre-hardened steel

Titanium alloy
Inconel718
%< 15
%< 15
%< 15
%>15
%>15
%>15
R
PRFRAD Revolution Feed rate Revolution Feed rate ap
pf
ap
pf
pf
Revolution Feed rate Revolution Feed rate ap
(mm)
R 1
R 1.5
R 2
R 2.5
R 3
R 4
R 5
R 6
R 8
R10
40000
32000
24000
19000
16000
12000
9600
8000
6000
4800
8000
7700
5800
5300
4800
4300
4100
4000
3200
3000
32000
21000
16000
12700
10600
8000
6400
5300
4000
3200
3800
3200
2800
2600
2100
1900
1800
1800
1400
1300
0.17
0.25
0.33
0.42
0.5
0.8
1
1.2
1.6
2
<0.5
36000 6500 24000

16000
18000
4000
12000
<1
9600
<1.25 14400 3500
12000 3200 8000
<1.5
9000 3200 6000
<2
7200 3000 4800
<2.5
6000 3000 4000
<3
4500 2500 3000
<4
3600 2300 2400
<5
<0.75 24000 4800
0.17
0.25
0.33
0.42
0.5
0.8
1
1.2
1.6
2
<0.5
9600
6400
4800
<1
<1.25 3800
3200
<1.5
2400
<2
2000
<2.5
1700
<3
1200
<4
1000
<5
<0.75
960
640
580
530
500
430
420
350
300
250
6400
4200
3200
2500
2100
1600
1300
1100
800
640
510
340
260
250
210
190
180
150
130
100
0.08
0.13
0.17
0.21
0.25
0.4
0.5
0.6
0.8
1
<0.2
<0.3
<0.4
<0.5
<0.6
<0.8
<1
<1.2
<1.6
<2
< 0.2PRFRAD
< 0.5PRFRAD
Depth of
cut
2900
1900
1700
1500
1400
1400
1300
1300
1100
1000
< ap
< ap
PRFRAD:Radius
J280
PRFRAD
%
pf
ap
SOLID END MILLS
End mill
VF4MB
(<30HRC)
( < 45HRC)
UWC
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
VF
Copper Alloy
30
CARBIDE
Aluminium Alloy
LF
0.01
PRFRAD
Type2
APMX
1 < DC < 12
LF
0
- 0.020
h6
BALL
0.5<PRFRAD<6
DCON(h6)
APMX
DCON(h6)
DC
Type1
DC
PRFRAD
SQUARE
15

0
- 0.008
0
- 0.009
0
- 0.011
DC
APMX
LF
DCON
Stock
VF4MBR0050
VF4MBR0100
VF4MBR0150
VF4MBR0200
VF4MBR0250
VF4MBR0300
VF4MBR0400
VF4MBR0500
VF4MBR0600
0.5
1
1.5
2
2.5
3
4
5
6
1
2
3
4
5
6
8
10
12
2.5
6
8
8
12
12
14
18
22
50
60
70
70
80
80
90
100
110
6
6
6
6
6
6
8
10
12
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
2
2
2
2
TAPER
PRFRAD
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 4 flute ball nose end mill for high-speed machining of hardened steel.
J281

CARBIDE
VF4MB
Work
material
AISI H13
AISI D2
AISI W1, AISI M2
%>15
%< 15
%>15
%< 15
%>15
%< 15
R
Depth of cut
Depth of cut
Depth of cut
Revolution
Feed
rate
Feed
rate
Revolution
Feed
rate
Revolution
Revolution
Feed rate ap(mm)
ap(mm)
ap(mm)
(mm)
(min-1) (mm/min) (min-1) (mm/min)
R0.5
R1
R1.5
R2
R2.5
R3
R4
R5
R6
40000 8000 40000

40000 9600 40000
40000 12000 32000
32000 11000 24000
25000 9000 19000
21000 8400 15000
16000 6400 12000
13000 5200 9600
9000 3600 7200
3800
5600
5600
4700
3800
3400
2600
2200
1700
0.06
0.11
0.13
0.15
0.20
0.25
0.30
0.50
0.50
40000
40000
32000
24000
19000
16000
12000
10000
7000
5600
8000
7700
6200
5300
4800
3600
3200
2200
40000
28000
19000
14000
12000
9600
7200
5800
4300
3100
3100
2900
2500
2200
2000
1600
1300
940
0.05
0.10
0.12
0.13
0.15
0.20
0.20
0.20
0.30
40000
24000
16000
12000
9600
8000
6000
4800
3600
4700
5000
4200
3100
2700
2300
1900
1500
1100
32000
16000
11000
8000
6000
5000
4000
3000
2200
1700
1200
1100
1000
780
780
620
550
400
0.03
0.06
0.07
0.08
0.08
0.09
0.09
0.10
0.10
< 0.2PRFRAD
Depth of
cut
< ap
PRFRAD:Radius

J282
PRFRAD
%
pf
ap
SOLID END MILLS
End mill
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
VQ
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
45
CARBIDE
Aluminium Alloy
12
DC
DN
Hardened Steel
( < 55HRC)
UWC
APMX
LU
DCON(h6)
Type1
PRFRAD
DN
LF
SQUARE
VQ4SVB
PRFRAD
DC < 12
0
- 0.02
APMX
LU
LF

0
- 0.011
a 4 flute ball nose end mill

a With the special substrate, suitable for finishing of heat resistance alloy, etc.
Order Number
PRFRAD
DC
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
Type
Unit : mm
VQ4SVBR0100
VQ4SVBR0150
VQ4SVBR0200
VQ4SVBR0250
VQ4SVBR0300
VQ4SVBR0400
VQ4SVBR0500
VQ4SVBR0600
1
1.5
2
2.5
3
4
5
6
2
3
4
5
6
8
10
12
3
4.5
6
7.5
9
12
15
18
5
7.5
10
12.5
15
20
25
30
1.9
2.9
3.9
4.9
5.85
7.85
9.7
11.7
50
50
50
50
50
60
70
75
6
6
6
6
6
8
10
12
4
4
4
4
4
4
4
4
1
1
1
1
2
2
2
2
a
a
a
a
a
a
a
RADIUS
0
- 0.009
TAPER
0
- 0.008
SOLID END MILLS
h6
Type2
DCON(h6)
0.01
BALL
1<PRFRAD<6
DC
J283

CARBIDE
VQ4SVB
y Shoulder milling(Slotting)
Work
material

Mild steel,
Pre-hardened steel
Austenitic stainless steel, Titanium alloy, Precipitation hardeningstainless steel,

Cobalt chromium alloy, Ferritic, Precipitation hardeningstainless steel
AISI 304, AISI 316, Ti-6Al-4V, AISI 630, AISI 631, 15-5PH, 17-4PH,
AISI 431, AISI 420
AISI 1045, AISI 4140, ASTM A36, AISI 1010, AISI P21, AISI P20,
AISI 4340
%< 15
%< 15
%>15
%>15
R
PRFRAD Cutting speed Revolution Feed rate Cutting speed Revolution Feed rate
ap
ap
pf
pf
Cutting speed Revolution Feed rate Cutting speed Revolution Feed rate
(mm)
(mm)
(mm)
(m/min) (min-1) (mm/min) (m/min) (min-1) (mm/min) (mm)
R
R
R
R
R
R
R
R
1
1.5
2
2.5
3
4
5
6
250
300
300
300
300
300
300
300
40000
32000
24000
19000
16000
12000
9600
8000
8000
7700
5800
5300
4800
4300
4100
4000
200
200
200
200
200
200
200
200
32000
21000
16000
12700
10600
8000
6400
5300
3800
3200
2800
2600
2100
1900
1800
1800
0.17
0.25
0.33
0.42
0.5
0.8
1
1.2
0.5
0.75
1
1.25
1.5
2
2.5
3
230
230
230
230
230
230
230
230
36000
24000
18000
14400
12000
9000
7200
6000
6500
4800
4000
3500
3200
3200
3000
3000
150
150
150
150
150
150
150
150
24000
16000
12000
9600
8000
6000
4800
4000
2900
1900
1700
1500
1400
1400
1300
1300
0.17
0.25
0.33
0.42
0.5
0.8
1
1.2
0.5
0.75
1
1.25
1.5
2
2.5
3
< pf
Depth of
cut
< ap
PRFRAD:Radius
Work
material
SOLID END MILLS
Inconel718
%< 15
%< 15
%>15
%>15
R
PRFRAD Cutting speed Revolution Feed rate Cutting speed Revolution Feed rate
ap
ap
pf
pf
Cutting speed Revolution Feed rate Cutting speed Revolution Feed rate
(mm)
(mm)
(mm)
R
R
R
R
R
R
R
R
1
1.5
2
2.5
3
4
5
6
250
360
360
360
360
360
360
360
40000
38000
29000
23000
19000
14000
12000
9600
8000
9100
7000
6400
5700
5000
5100
4800
240
240
240
240
240
240
240
240
38000
25000
19000
15000
13000
9600
7700
6400
4500
3800
3300
3100
2600
2300
2200
2200
0.17
0.25
0.33
0.42
0.5
0.8
1
1.2
0.5
0.7
1
1.2
1.5
2
2.5
3
60
60
60
60
60
60
63
64
9600
6400
4800
3800
3200
2400
2000
1700
960
640
580
530
500
430
420
350
40
40
40
39
40
40
41
41
6400
4200
3200
2500
2100
1600
1300
1100
510
340
260
250
210
190
180
150
0.08
0.13
0.17
0.21
0.25
0.4
0.5
0.6
0.2
0.3
0.4
0.5
0.6
0.8
1
1.2
< pf
Depth of
cut
< ap
PRFRAD:Radius
2) For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective.
End mill
pf
J284
ap
PRFRAD
VC4MB
e
Copper Alloy
Aluminium Alloy
DC
APMX
0.01
0.02
DC < 12
DC>12
0
- 0.030
PRFRAD

0
- 0.008
0
- 0.009
APMX
0
- 0.011
APMX
Type3
LF
DC
PRFRAD<6 PRFRAD>7
0
- 0.020
h6
PRFRAD
Type2
LF
DC
PRFRAD
Type1
SQUARE
Titanium Alloy,
BALL
Austenitic
Stainless Steel
DCON(h6)
Hardened Steel
(>55HRC)
15
CARBIDE
PRFRAD<3 PRFRAD > 3
Hardened Steel
( < 55HRC)
30
DCON(h6)
20
DCON(h6)
(<30HRC)
( < 45HRC)
VC
UWC
LF
0
- 0.013
DC
APMX
LF
DCON
Stock
VC4MBR0050
VC4MBR0075
VC4MBR0100
VC4MBR0150
VC4MBR0200
VC4MBR0250
VC4MBR0300
VC4MBR0400
VC4MBR0500
VC4MBR0600
VC4MBR0700
VC4MBR0800
VC4MBR0900
VC4MBR1000
0.5
0.75
1
1.5
2
2.5
3
4
5
6
7
8
9
10
1
1.5
2
3
4
5
6
8
10
12
14
16
18
20
2.5
4
6
8
8
12
12
14
18
22
26
30
34
38
50
50
60
70
70
80
80
90
100
110
120
140
140
160
6
6
6
6
6
6
6
8
10
12
12
16
16
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
2
2
2
2
3
2
3
2
TAPER
PRFRAD
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 4 flute ball nose end mill with high durability for hardened steels.
J285

CARBIDE
VC4MB
Alloy steel, Tool steel, Pre-hardened steel,

Work Hardened steel ( 55HRC)
material
AISI D2
%>15
% < 15
R
PRFRAD
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
R 0.5
R 0.75
R1
R 1.5
R2
R 2.5
R3
R4
R5
R6
40000
40000
40000
40000
32000
25000
21000
16000
13000
9000
8000
9600
9600
12000
11000
9000
8400
6400
5200
3600
40000
40000
40000
32000
24000
19000
15000
12000
9600
7200
3800
4800
5600
5600
4700
3800
3400
2600
2200
1700
Depth of
cut
Depth of cut
(mm)
0.06
0.09
0.11
0.13
0.15
0.20
0.25
0.30
0.50
0.50
%>15
% < 15
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
40000
40000
40000
32000
24000
19000
16000
12000
10000
7000
5600
7200
8000
7700
6200
5300
4800
3600
3200
2200
40000
38000
28000
19000
14000
12000
9600
7200
5800
4300
3100
4200
3100
2900
2500
2200
2000
1600
1300
940
Depth of cut
(mm)
0.05
0.08
0.10
0.12
0.13
0.15
0.20
0.20
0.20
0.30
< 0.2PRFRAD
< Please
PRFRAD:Radius
SOLID END MILLS
J286
MSTAR END MILLS
MS2MRB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
MS
UWC
30
CARBIDE
DC<3
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DC > 3
Aluminium Alloy
Type1
DCON(h6)
RE
APMX
LF
Type2
APMX
LF
1 < DC < 12
0
- 0.020
h6
BALL
DCON(h6)
DC
RE
SQUARE
DC
15

0
- 0.008
0
- 0.009
0
- 0.011
RE
APMX
LF
DCON
Stock
MS2MRBD0100R010
MS2MRBD0100R020
MS2MRBD0100R030
MS2MRBD0150R010
MS2MRBD0150R020
MS2MRBD0150R030
MS2MRBD0150R050
MS2MRBD0200R010
MS2MRBD0200R020
MS2MRBD0200R030
MS2MRBD0200R050
MS2MRBD0250R010
MS2MRBD0250R020
MS2MRBD0250R030
MS2MRBD0250R050
MS2MRBD0300R010
MS2MRBD0300R020
MS2MRBD0300R030
MS2MRBD0300R050
MS2MRBD0300R100
MS2MRBD0400R010
MS2MRBD0400R020
MS2MRBD0400R030
MS2MRBD0400R050
MS2MRBD0400R100
MS2MRBD0500R010
MS2MRBD0500R020
MS2MRBD0500R030
MS2MRBD0500R050
MS2MRBD0500R100
MS2MRBD0600R010
MS2MRBD0600R020
MS2MRBD0600R030
MS2MRBD0600R050
1
1
1
1.5
1.5
1.5
1.5
2
2
2
2
2.5
2.5
2.5
2.5
3
3
3
3
3
4
4
4
4
4
5
5
5
5
5
6
6
6
6
0.1
0.2
0.3
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
6
6
6
6
6
8
8
8
8
8
10
10
10
10
10
12
12
12
12
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute corner radius end mill for general use.
J287
MSTAR END MILLS
MS2MRB
J288
Order Number
DC
RE
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
MS2MRBD0600R100
MS2MRBD0600R150
MS2MRBD0600R200
MS2MRBD0800R020
MS2MRBD0800R030
MS2MRBD0800R050
MS2MRBD0800R100
MS2MRBD0800R150
MS2MRBD0800R200
MS2MRBD0800R250
MS2MRBD0800R300
MS2MRBD1000R020
MS2MRBD1000R030
MS2MRBD1000R050
MS2MRBD1000R100
MS2MRBD1000R150
MS2MRBD1000R200
MS2MRBD1000R250
MS2MRBD1000R300
MS2MRBD1200R020
MS2MRBD1200R030
MS2MRBD1200R050
MS2MRBD1200R100
MS2MRBD1200R150
MS2MRBD1200R200
MS2MRBD1200R250
MS2MRBD1200R300
6
6
6
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
1
1.5
2
0.2
0.3
0.5
1
1.5
2
2.5
3
0.2
0.3
0.5
1
1.5
2
2.5
3
0.2
0.3
0.5
1
1.5
2
2.5
3
12
12
12
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
24
24
24
24
24
24
24
24
50
50
50
60
60
60
60
60
60
60
60
70
70
70
70
70
70
70
70
75
75
75
75
75
75
75
75
6
6
6
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
CARBIDE

Work
material

Pre-hardened steel
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.5
2
2.5
3
4
5
6
8
10
12
16
20
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
30000
24000
20000
15000
12000
10000
8000
6400
5400
2400
1900
40
100
200
600
1000
1200
1400
1600
1800
2000
3000
3000
2600
2300
2000
1600
1400
1000
900
820
380
320
0.001
0.002
0.005
0.01
0.015
0.02
0.02
0.03
0.04
0.06
0.12
0.18
0.25
0.30
0.40
0.50
0.60
0.80
1.00
1.00
3.00
4.00
40000
40000
40000
40000
40000
40000
40000
40000
40000
32000
32000
24000
19000
16000
12000
9000
7000
5600
4500
3800
1200
1000
40
100
200
600
960
1200
1400
1600
1600
1600
1900
1900
1600
1400
1200
900
700
550
500
450
100
80
0.001
0.002
0.005
0.01
0.015
0.02
0.02
0.03
0.04
0.06
0.08
0.10
0.13
0.15
0.20
0.25
0.30
0.40
0.50
0.50
0.80
1.00

for depth of cut.
Depth of
cut
< 1DC
DC
< Please

for depth of cut.
DC:Dia.
SOLID END MILLS
< Please
J289
MSTAR END MILLS
MS2XLRB
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
DC<3
Austenitic
Stainless Steel
Titanium Alloy,
30
Copper Alloy
DC > 3
Aluminium Alloy
B2
DC
SQUARE
DN
Hardened Steel
( < 55HRC)
MS
UWC
RE
Effective length
for inclined angle
DN
DC
APMX
LU
LF
Inclined angle
Type2
DCON(h6)
Effective
length
BALL
15
LF
RE
1 < DC < 6
Type1
APMX
LU
DCON(h6)
CARBIDE
0
- 0.020
h6
DCON=6
0
- 0.008
a 2 flute long neck corner radius end mill.
MS2XLRBD0100R010N020
1
1
2
2
2
2
3
3
3
3
4
4
4
4
4
4
6
6
6
6
6
6
J290
RE APMX
LU
DN
B2
LF
DCON
0.1
0.1
0.1
0.1
0.3
0.3
0.1
0.1
0.3
0.3
0.1
0.1
0.3
0.3
0.5
0.5
0.1
0.1
0.3
0.3
0.5
0.5
2
5
4
10
4
10
6
15
6
15
8
20
8
20
8
20
12
30
12
30
12
30
0.94
0.94
1.90
1.90
1.90
1.90
2.90
2.90
2.90
2.90
3.90
3.90
3.90
3.90
3.90
3.90
5.85
5.85
5.85
5.85
5.85
5.85
12.3
9.8
9.9
6.5
10
6.6
7.4
4.2
7.5
4.2
4.9
2.5
5
2.5
5
2.5
60
60
60
60
60
60
50
60
50
60
50
60
50
60
50
60
50
70
50
70
50
70
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
2
2
2
2
3
3
3
3
4
4
4
4
4
4
6
6
6
6
6
6
Type
DC
Stock
Order Number
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
Unit : mm
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
2.1
5.3
4.2
10.5
4.2
10.5
6.3
15.7
6.3
15.7
8.4
20.8
8.4
20.8
8.4
20.8
2.3
5.6
4.4
10.9
4.4
10.8
6.6
16.2
6.6
16.2
8.7
21.6
8.7
21.5
8.7
21.5
2.4
6.0
4.8
11.7
4.7
11.6
7.1
17.4
7.0
17.4
9.4
23.2
9.3
23.1
9.3
23.1
2.8
6.5
5.2
12.6
5.1
12.6
7.6
18.8
7.6
18.8
10.1
*
*
*
*
*
*
10.1
10.0
*
* * *
* * *
* * *
* * *
* * *
*No interference
* *
CARBIDE

Work material
Dia.
DC (mm)
1
2
3
4
6
1
2
3
4
6
Neck length
LU (mm)
2
4
6
8
12
5
10
15
20
30
(2D)
(5D)


Pre-hardened steel

Titanium alloy

AISI P20
AISI H13
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
30000
15000
10000
7500
5000
22000
11000
7400
5600
3700
600
600
600
600
600
350
350
350
350
350
20000
10000
7000
5200
3500
17000
8800
5800
4400
2900
400
400
400
400
400
280
280
280
280
280
18000
9100
6000
4500
3000
14000
7200
4800
3600
2400
300
300
300
300
300
200
200
200
200
200
15000
8000
5000
4000
2700
12000
6400
4200
3200
2100
120
120
120
120
120
100
100
100
100
100
(Neck length=2D)
(Neck length=2D)
<0.1DC (DC <& 3)

<0.2DC (DC > & 3)
<0.05DC
DC
<0.1DC
<1.5DC
<0.2DC
(DC < & 2)

(DC >& 2)
DC
<1DC
<0.05DC
<0.1DC
(DC <& 2)
(DC > & 2)
Depth of cut
<0.05DC
<1DC
(Neck length=5D)
<0.02DC
DC
<0.05DC
<1DC
DC
<0.02DC
DC:Dia.
SOLID END MILLS
(Neck length=5D)
J291
MIRACLE END MILLS
VCPSRB
Corner radius end mill, Short cut length, 2 4 flute, High precision
(<30HRC)
( < 45HRC)
DC < 1.5
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
30
Copper Alloy
DC > 2
Aluminium Alloy
B2
DC
SQUARE
DN
VC
UWC
Type1
RE
BALL
DN
0.01
Type2
RE
0.6<DC<12
Inclined angle
APMX
LU
LF
0
- 0.01
h5
DCON(h5)
0.05<RE<5
LF
DC
Effective
length
Effective length
for inclined angle
15
APMX
LU
DCON(h5)
CARBIDE

0
- 0.005
0
- 0.006
0
- 0.008
End mill with corner radius for precise and efficient machining.
RE
APMX
VCPSRBD0060N02R005
VCPSRBD0060N02R01
VCPSRBD0060N02R02
VCPSRBD0060N04R01
VCPSRBD0060N04R02
VCPSRBD0080N04R005
VCPSRBD0080N04R01
VCPSRBD0080N04R02
VCPSRBD0080N04R03
VCPSRBD0080N06R01
VCPSRBD0080N06R02
VCPSRBD0080N06R03
VCPSRBD0080N08R03
VCPSRBD0100N04R005
VCPSRBD0100N04R01
VCPSRBD0100N04R02
VCPSRBD0100N04R03
VCPSRBD0100N04R04
VCPSRBD0100N06R01
VCPSRBD0100N06R02
VCPSRBD0100N06R03
VCPSRBD0100N06R04
VCPSRBD0100N10R03
VCPSRBD0100N10R04
VCPSRBD0120N06R05
VCPSRBD0120N10R05
VCPSRBD0120N15R05
VCPSRBD0150N04R01
VCPSRBD0150N04R02
VCPSRBD0150N04R03
VCPSRBD0150N04R05
VCPSRBD0150N06R01
VCPSRBD0150N06R02
VCPSRBD0150N06R03
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
0.05
0.1
0.2
0.1
0.2
0.05
0.1
0.2
0.3
0.1
0.2
0.3
0.3
0.05
0.1
0.2
0.3
0.4
0.1
0.2
0.3
0.4
0.3
0.4
0.5
0.5
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
J292
LU
DN
B2
LF
DCON
2
2
2
4
4
4
4
4
4
6
6
6
8
4
4
4
4
4
6
6
6
6
10
10
6
10
15
4
4
4
4
6
6
6
0.56
0.56
0.56
0.56
0.56
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.76
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.14
1.14
1.14
1.44
1.44
1.44
1.44
1.44
1.44
1.44
12.6
12.6
12.7
10.9
11
10.7
10.8
10.8
10.9
9.4
9.5
9.5
8.5
10.5
10.5
10.6
10.6
10.7
9.2
9.2
9.3
9.4
7.4
7.4
9.3
7.3
5.8
10.2
10.2
10.3
10.5
8.8
8.9
8.9
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Type
DC
Stock
Order Number
Unit : mm
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
a 0.01mm corner radius tolerance, 0 -0.01mm outer diameter tolerance.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
2.1 2.2
2.1 2.2
2.1 2.2
4.2 4.4
4.2 4.3
4.2 4.4
4.2 4.4
4.2 4.3
4.2 4.3
6.3 6.5
6.3 6.5
6.3 6.5
8.3 8.6
4.2 4.5
4.2 4.5
4.2 4.5
4.2 4.5
4.2 4.5
6.4 6.7
6.4 6.7
6.3 6.6
6.3 6.6
10.5 10.9
10.5 10.9
6.3 6.6
10.5 10.9
15.7 16.3
4.2 4.5
4.2 4.5
4.2 4.5
4.2 4.4
6.4 6.7
6.4 6.7
6.3 6.6
2.4
2.3
2.2
4.7
4.7
4.7
4.7
4.7
4.6
7
7
6.9
9.2
4.8
4.8
4.7
4.6
4.4
7.2
7.2
7.2
7.1
11.8
11.7
7.1
11.7
17.5
4.8
4.7
4.6
4.3
7.2
7.2
7.2
2.6
2.6
2.5
5.1
5
5.1
5.1
5
5
7.5
7.5
7.5
10
5.3
5.3
5.3
5.2
5.2
7.8
7.7
7.7
7.7
12.7
12.7
7.7
12.6
18.9
5.3
5.3
5.2
5.2
7.8
7.7
7.7
CARBIDE
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
LF
DCON
6
10
10
10
10
15
15
15
15
20
20
6
6
6
6
10
10
10
10
15
15
15
15
20
20
25
25
8
8
8
8
8
15
15
15
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
30
30
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
9
6.9
7
7
7.1
5.5
5.5
5.5
5.7
4.7
4.8
9.4
9.7
10
10.3
7.6
7.7
7.8
8
5.9
5.9
6
6.1
4.8
4.9
4
4
8.6
8.7
8.8
9
9.4
5.5
5.6
5.7
6.6
6.6
6.6
6.7
7
4.8
4.8
4.8
4.8
5
3.7
3.7
3.8
3.8
3.9
2.6
2.6
50
50
50
50
50
50
50
50
50
60
60
50
50
50
50
50
50
50
50
50
50
50
50
60
60
60
60
50
50
50
50
50
50
50
50
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
70
70
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
6.3 6.6
10.6 11
10.5 11
10.5 10.9
10.5 10.9
15.8 16.3
15.8 16.3
15.7 16.3
15.7 16.3
20.9 21.6
20.9 21.5
6.3 6.6
6.3 6.6
6.3 6.6
6.3 6.5
10.5 10.9
10.5 10.8
10.5 10.8
10.5 10.8
15.7 16.1
15.7 16.1
15.7 16.1
15.6 16.1
20.8 21.4
20.8 21.4
26 26.6
26 26.6
8.4 8.7
8.4 8.7
8.4 8.7
8.4 8.7
8.3 8.7
15.7 16.1
15.6 16.1
15.6 16.1
10.5 10.9
10.5 10.8
10.5 10.8
10.5 10.8
10.4 10.8
15.7 16.1
15.7 16.1
15.7 16.1
15.6 16.1
15.6 16.1
20.8 21.4
20.8 21.4
20.8 21.4
20.8 21.4
20.8 21.3
31.1 31.8
31.1 31.8
7.1
11.8
11.8
11.8
11.7
17.5
17.5
17.5
17.4
22.9
22.8
6.9
6.8
6.7
6.5
11.4
11.2
11.1
10.9
16.8
16.7
16.6
16.3
21.9
21.7
27.5
27
9.2
9
8.9
8.7
8.2
16.6
16.3
15.8
11.4
11.2
11.1
10.9
10.4
16.8
16.7
16.6
16.3
15.8
22.1
22
21.9
21.7
21.2
32.5
32.2
7.7
12.7
12.7
12.7
12.6
18.9
18.9
18.9
18.6
24.5
24.2
7.5
7.4
7.4
7.4
12
12
11.9
11.9
17.5
17.5
17.4
17.4
22.9
22.9
28.3
28.2
9.9
9.9
9.9
9.9
9.9
17.5
17.5
17.5
12.3
12.3
12.3
12.4
12.4
17.7
17.8
17.8
17.8
17.8
23.1
23.1
23.2
23.2
23.2
SQUARE
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
0.3
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
0.3
0.5
0.3
0.5
0.1
0.2
0.3
0.5
1
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.3
0.5
B2
BALL
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
DN
RADIUS
VCPSRBD0150N06R05
VCPSRBD0150N10R01
VCPSRBD0150N10R02
VCPSRBD0150N10R03
VCPSRBD0150N10R05
VCPSRBD0150N15R01
VCPSRBD0150N15R02
VCPSRBD0150N15R03
VCPSRBD0150N15R05
VCPSRBD0150N20R03
VCPSRBD0150N20R05
VCPSRBD0200N06R01
VCPSRBD0200N06R02
VCPSRBD0200N06R03
VCPSRBD0200N06R05
VCPSRBD0200N10R01
VCPSRBD0200N10R02
VCPSRBD0200N10R03
VCPSRBD0200N10R05
VCPSRBD0200N15R01
VCPSRBD0200N15R02
VCPSRBD0200N15R03
VCPSRBD0200N15R05
VCPSRBD0200N20R03
VCPSRBD0200N20R05
VCPSRBD0200N25R03
VCPSRBD0200N25R05
VCPSRBD0250N08R01
VCPSRBD0250N08R02
VCPSRBD0250N08R03
VCPSRBD0250N08R05
VCPSRBD0250N08R10
VCPSRBD0250N15R03
VCPSRBD0250N15R05
VCPSRBD0250N15R10
VCPSRBD0300N10R01
VCPSRBD0300N10R02
VCPSRBD0300N10R03
VCPSRBD0300N10R05
VCPSRBD0300N10R10
VCPSRBD0300N15R01
VCPSRBD0300N15R02
VCPSRBD0300N15R03
VCPSRBD0300N15R05
VCPSRBD0300N15R10
VCPSRBD0300N20R01
VCPSRBD0300N20R02
VCPSRBD0300N20R03
VCPSRBD0300N20R05
VCPSRBD0300N20R10
VCPSRBD0300N30R03
VCPSRBD0300N30R05
LU
TAPER
APMX
SOLID END MILLS
RE
Type
DC
Stock
Order Number
No. of Flutes
Unit : mm
*
*
No interference
J293
MIRACLE END MILLS
VCPSRB
J294
RE
APMX
LU
DN
B2
LF
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.3
0.5
1
0.5
1
0.5
1
0.1
0.2
0.3
0.5
1
2
0.5
1
0.1
0.2
0.3
0.5
1
2
3
1
3
0.3
0.5
1
2
3
4
1
3
0.3
0.5
1
2
3
4
5
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
20
20
20
20
20
30
30
30
15
15
30
30
18
18
18
18
18
18
41
50
24
24
24
24
24
24
24
50
50
30
30
30
30
30
30
50
50
36
36
36
36
36
36
36
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
4.9
4.9
4.9
4.9
5.85
5.85
5.85
5.85
5.85
5.85
5.85
5.85
7.85
7.85
7.85
7.85
7.85
7.85
7.85
7.85
7.85
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
3.8
3.8
3.8
3.9
4
2.5
2.5
2.5
2.5
2.6
1.8
1.8
1.8
1.6
1.6
0.9
0.9
60
60
60
60
60
60
60
60
60
60
70
70
70
60
60
70
70
70
70
70
70
70
70
90
90
90
90
90
90
90
90
90
90
90
100
100
100
100
100
100
100
100
110
110
110
110
110
110
110
DCON
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Type
VCPSRBD0400N12R01
VCPSRBD0400N12R02
VCPSRBD0400N12R03
VCPSRBD0400N12R05
VCPSRBD0400N12R10
VCPSRBD0400N20R01
VCPSRBD0400N20R02
VCPSRBD0400N20R03
VCPSRBD0400N20R05
VCPSRBD0400N20R10
VCPSRBD0400N30R03
VCPSRBD0400N30R05
VCPSRBD0400N30R10
VCPSRBD0500N15R05
VCPSRBD0500N15R10
VCPSRBD0500N30R05
VCPSRBD0500N30R10
VCPSRBD0600N18R01
VCPSRBD0600N18R02
VCPSRBD0600N18R03
VCPSRBD0600N18R05
VCPSRBD0600N18R10
VCPSRBD0600N18R20
VCPSRBD0600N41R05
VCPSRBD0600N50R10
VCPSRBD0800N24R01
VCPSRBD0800N24R02
VCPSRBD0800N24R03
VCPSRBD0800N24R05
VCPSRBD0800N24R10
VCPSRBD0800N24R20
VCPSRBD0800N24R30
VCPSRBD0800N50R10
VCPSRBD0800N50R30
VCPSRBD1000N30R03
VCPSRBD1000N30R05
VCPSRBD1000N30R10
VCPSRBD1000N30R20
VCPSRBD1000N30R30
VCPSRBD1000N30R40
VCPSRBD1000N50R10
VCPSRBD1000N50R30
VCPSRBD1200N36R03
VCPSRBD1200N36R05
VCPSRBD1200N36R10
VCPSRBD1200N36R20
VCPSRBD1200N36R30
VCPSRBD1200N36R40
VCPSRBD1200N36R50
DC
Stock
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
Order Number
Unit : mm
No. of Flutes
CARBIDE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
12.5
12.5
12.5
12.5
12.5
20.8
20.8
20.8
20.8
20.8
31.1
31.1
31.1
15.6
15.6
31.1
31.1
13
13
13
13
12.9
21.4
21.4
21.4
21.4
21.3
31.8
31.8
31.8
16.1
16.1
13.5
13.4
13.3
13.1
12.6
22.1
22
21.9
21.7
21.2
15.1
15.2
15.2
15.3
15.3
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* No interference
CARBIDE
Work material
Dia.
DC (mm)

Pre-hardened steel
AISI H13
AISI D2
Neck length
LU (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
4
4
6
8
4
6
10
6
10
15
4
6
10
6
10
15
8
15
10
15
20
12
20
30
15
30
18
41
50
24
50
30
50
36
48000
48000
48000
38000
29000
48000
38000
29000
48000
38000
29000
41000
32000
24000
36000
29000
22000
33000
20000
30000
24000
18000
26000
20000
15000
20000
12000
20000
15000
10000
15000
10000
12000
10000
10000
200 600
160 500
240 750
190 600
150 450
270 900
220 720
160 540
300 900
240 720
180 540
300 900
240 720
180 540
600 2000
480 1600
360 1200
750 2400
450 1400
900 3000
720 2400
540 1800
1200 4500
960 2000
720 1000
1200 4800
720 1900
1600 7500
900 2400
600 1200
1900 7500
1300 2400
1600 7500
1300 3200
1500 7500
40000
40000
32000
26000
19000
32000
26000
19000
32000
26000
19000
27000
22000
16000
24000
19000
14000
22000
13000
20000
16000
12000
17000
14000
10000
13000
8000
13000
12000
8000
10000
8000
8000
7000
7000
160 500
100 300
160 500
130 400
100 300
180 600
150 480
110 360
200 600
160 480
120 360
200 600
160 480
120 360
400 1300
320 1000
240 780
500 1600
300 960
600 2000
480 1600
360 1200
800 3000
640 2000
480 1000
780 3120
480 1600
1100 5000
720 1600
480 800
1300 5000
1000 2200
1100 5000
950 2200
1000 5000
22000
22000
19000
16000
12000
19000
16000
12000
19000
15000
12000
16000
13000
10000
14000
12000
9000
13000
8000
12000
10000
7000
10000
8000
6000
10000
7000
8000
10000
6000
6000
3000
5000
2500
4000
80 250
50 150
80 250
70 200
50 150
90 300
70 240
60 180
100 300
80 240
60 180
100 300
80 240
60 180
200 650
160 520
120 390
250 800
150 480
300 1000
240 800
180 600
400 1500
320 2000
240 1000
520 2000
360 1120
550 2500
600 1200
360 530
650 2500
320 600
550 2500
280 600
500 2500
0.6
0.8
1.2
1.5
2
2.5
3
4
5
6
8
10
12
< 0.2RE
Depth of cut
< 0.4RE
(DC < &2)

(DC > &2)
< 0.1RE
(DC < &1.5)

< 0.2mm (DC < &4)
< 0.5mm (DC < &6)
< 0.1mm
< 0.2RE
(DC < &2)

(DC > &2)
SOLID END MILLS
(DC < &1.5)

(DC < &4)
< 0.3mm (DC < &6)
< 0.05mm
< 0.1mm
DC:Dia.
1) The cutting conditions above are a guide only to machining with cutting edges with a corner radius. When machining with peripheral cutting
edges, use the minimum feed rate as a guide.
3) For profile machining such as moulds, machining conditions may differ considerably depending on the workpiece geometry, machining
methods and depth of cut. Reduce the feed rate especially when machining the corner sections of a workpiece.
J295
MIRACLE END MILLS
VCPSRB
(<30HRC)
( < 45HRC)
DC < 1.5
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
30
DN
Taper neck type
Copper Alloy
DC > 2
Aluminium Alloy
B2
BHTA
DC
Type3
15
RE
Effective length
for inclined angle
0.5 < RE < 3
APMX
LU
LU_2
DCON(h5)
SQUARE
VC
UWC
Effective
length
CARBIDE
LF
BALL
0.01
Inclined angle
1.5<DC<12
0
- 0.01
h5

0
- 0.005
0
- 0.006
0
- 0.008
End mill with corner radius for precise and efficient machining.
RE BHTA APMX LU_2 LU

0.5
0.5
0.5
0.5
1
1
0.5
0.5
1
1
1
1
0.5
0.5
1
1
2
2
2
2
3
3
3
1 30' 1.5
1 30' 1.5
1 30' 2
1 30' 2
1 30' 2.5
1 30' 2.5
1 30' 3
1 30' 3
1 30' 3
1 30' 3
1 30' 4
1 30' 4
1
5
1
5
1
5
1
5
1
6
1
6
1
8
1
8
1
10
1
10
1
12
6
10
10
15
12
20
15
20
15
20
20
30
40
60
40
60
40
60
53
70
55
70
70
3
3
4
4
5
5
6
6
6
6
8
8
8
8
8
8
8
8
10
10
12
12
24
DN
B2
LF DCON
1.44
1.44
1.9
1.9
2.4
2.4
2.9
2.9
2.9
2.9
3.9
3.9
4.9
4.9
4.9
4.9
5.85
5.85
7.85
7.85
9.7
9.7
11.7
9
7.2
6.7
5.3
5.6
4
4.4
3.6
4.4
3.6
2.6
1.9
2
1.4
2
1.4
1.4
1
1.1
1.6
1.1
0.9
1.6
50
50
60
60
60
60
60
60
60
60
60
70
90
110
90
110
70
100
90
130
100
130
130
2
2
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
10
12
12
12
16
Type
VCPSRBD0150N03L06R05
1.5
1.5
2
2
2.5
2.5
3
3
3
3
4
4
5
5
5
5
6
6
8
8
VCPSRBD1000N12L55R30 10
J296
DC
Stock
Order Number
Unit : mm
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
41.2
61.2
41.7
61.7
42.8
7.1
11.3
11.5
16.7
14.2
22.5
16.9
22.1
17.4
22.6
22.8
7.7
12.2
12.4
18
15.3
24.2
18.2
23.8
18.7
24.4
*
* *
* *
* *
* *
* *
* *
* * *
55.9
* *
72.9
* *
59.4
* *
* * *
75.2
* *
* No interference
CARBIDE

Pre-hardened steel
AISI H13
AISI D2
Work material
Dia.
DC (mm)
1.5
2
2.5
3
4
5
6
8
10
Taper angle one side

DHTA
Neck length
LU_2 (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
130'
130'
130'
130'
130'
130'
130'
130'
130'
130'
1
1
1
1
1
6
10
10
15
12
20
15
20
20
30
40
60
40
53
55
36000
28000
32000
25000
26000
20000
27000
21000
23000
18000
10000
7000
20000
15000
12000
270 810
210 630
540 1800
420 1400
600 1900
450 140
810 2700
630 2100
1080 3000
840 1500
520 1400
360 840
1650 4500
1950 4500
1650 4500
24000
19000
22000
17000
18000
13000
18000
14000
15000
12000
7000
5000
13000
10000
8000
180 540
140 420
360 1200
280 910
400 1300
300 960
540 1800
420 1400
720 3000
560 1500
420 840
300 500
1100 3000
1300 3000
1100 3000
15000
11000
13000
10000
11000
8000
11000
8000
9000
7000
5000
4000
8000
6000
5000
90 270
70 210
180 590
140 460
200 640
150 480
270 900
210 700
360 3000
280 1500
260 600
210 400
550 1500
650 1500
550 1500
< 0.2RE
Depth of cut
< 0.4RE
(DC < &2)

(DC > &2)
< 0.1RE
(DC < &1.5)

< 0.2mm (DC < &4)
< 0.5mm (DC < &6)
< 0.1mm
< 0.2RE
(DC < &2)

(DC > &2)
(DC < &1.5)

(DC < &4)
< 0.3mm (DC < &6)
< 0.05mm
< 0.1mm
1) The cutting conditions above are a guide only to machining with cutting edges with a corner radius. When machining with peripheral cutting
edges, use the minimum feed rate as a guide.
SOLID END MILLS
DC:Dia.
J297
CRN END MILLS
CRN2MRB
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
CRN
30
Copper Alloy
Aluminium Alloy
u
Type1
SQUARE
DC
(<30HRC)
( < 45HRC)
UWC
RE
DCON(h6)
CARBIDE
APMX
BALL
LF
6 < DC < 12
0
- 0.02
h6

0
- 0.008
0
- 0.009
0
- 0.011
a 2 flute corner radius end mill with CRN coating for copper electrode machining.
J298
Order Number
DC
RE
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
CRN2MRBD0600R020
CRN2MRBD0600R030
CRN2MRBD0600R050
CRN2MRBD0600R100
CRN2MRBD0800R030
CRN2MRBD0800R050
CRN2MRBD0800R100
CRN2MRBD1000R030
CRN2MRBD1000R050
CRN2MRBD1000R100
CRN2MRBD1200R030
CRN2MRBD1200R050
CRN2MRBD1200R100
6
6
6
6
8
8
8
10
10
10
12
12
12
0.2
0.3
0.5
1
0.3
0.5
1
0.3
0.5
1
0.3
0.5
1
13
13
13
13
19
19
19
22
22
22
26
26
26
50
50
50
50
60
60
60
70
70
70
75
75
75
6
6
6
6
8
8
8
10
10
10
12
12
12
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
CARBIDE

Work material
Dia.
DC (mm)
6
8
10
12
Corner radius
RE (mm)
Revolution
(min-1)
Feed rate
(mm/min)
R0.2, R0.3, R0.5

R1
R0.3, R0.5
R1
R0.3, R0.5
R1
R0.3, R0.5
R1
10000
10000
8000
8000
6400
6400
5400
5400
1400
1700
1000
1200
900
1100
800
1000
Depth of cut
ap
(mm)
ae
(mm)
6
6
8
8
10
10
12
12
0.6
0.6
0.8
0.8
1.0
1.0
1.0
1.0
< ae
Depth of cut
< ap
DC:Dia.
SOLID END MILLS
J299
CRN END MILLS
CRN2XLRB
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
CRN
UWC
30
DC<3
Titanium Alloy,
DC > 3
Copper Alloy
Aluminium Alloy
Type1
DC
SQUARE
DN
(<30HRC)
( < 45HRC)
DCON(h6)
Type2
DC
RE
Inclined angle
0.5 < DC < 6
LF
APMX
LU
DCON(h6)
BALL
Effective length
for inclined angle
15
APMX
LU
DN
RE
Effective
length
CARBIDE
LF
0
- 0.02
h6
4 < DCON < 6

0
- 0.008
a 2 flute long neck corner radius end mill with CRN coating for copper electrode machining.
RE
APMX
LU
DN
LF
DCON
CRN2XLRBD0050R005N04
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
3
3
0.05
0.1
0.05
0.1
0.05
0.1
0.05
0.1
0.1
0.3
0.1
0.3
0.1
0.3
0.1
0.2
0.3
0.1
0.2
0.3
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
0.1
0.2
0.3
0.5
0.2
0.3
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
3
3
4
4
6
6
6
6
8
8
8
8
10
10
12
12
12
12
12
20
20
20
12
12
12
12
16
16
16
16
20
20
20
20
20
20
0.46
0.46
0.46
0.46
0.76
0.76
0.76
0.76
0.94
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.44
1.44
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.9
2.9
50
50
50
50
50
50
50
50
50
50
55
55
55
55
55
55
55
60
60
60
55
55
55
55
55
55
55
55
60
60
60
60
65
65
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Type
DC
Stock
Order Number
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
Unit : mm
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
4.1
4.1
6.2
6.2
6.3
6.3
8.3
8.3
8.5
8.5
10.6
10.5
12.6
12.6
12.6
12.6
12.6
20.9
20.9
20.9
12.5
12.5
12.5
12.5
16.7
16.7
16.7
16.7
20.8
20.8
20.8
20.8
20.8
20.8
4.3
4.3
6.4
6.4
6.5
6.5
8.6
8.6
8.8
8.8
11
10.9
13.1
13.1
13.1
13.1
13.1
21.7
21.7
21.6
13
13
13
13
17.3
17.3
17.3
17.2
21.6
21.5
21.5
21.5
21.5
21.5
4.6
4.6
6.9
6.9
7
7
9.3
9.3
9.5
9.5
11.8
11.8
14.1
14.1
14.1
14.1
14.1
23.3
23.3
23.3
14
14
13.9
13.9
18.6
18.6
18.5
18.5
23.2
23.2
23.1
23.1
23.2
23.1
5
5
7.5
7.5
7.6
7.5
10
10
10.2
10.2
12.7
12.7
15.2
15.2
15.2
15.2
15.2
*
*
*
15.1
15.1
15
15
*
*
*
*
*
*
*
*
25
25
* No interference
a
J300
CARBIDE
LU
DN
LF
DCON
3
4
4
4
5
5
5
6
6
6
6
0.5
0.2
0.3
0.5
0.2
0.3
0.5
0.2
0.3
0.5
1
3
4
4
4
5
5
5
6
6
6
6
20
20
20
20
25
25
25
30
30
30
30
2.9
3.9
3.9
3.9
4.9
4.9
4.9
5.85
5.85
5.85
5.85
65
65
65
65
65
65
65
70
70
70
70
6
6
6
6
6
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
2
2
2
2
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
20.8
20.8
20.8
20.8
26
26
26
21.5
21.5
21.5
21.5
26.9
26.9
26.9
*
*
*
*
*
*
*
*
23.1 24.9
23.2
23.1
23.1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* No interference
y Contour Cutting
Corner radius
RE (mm)
0.5
R0.05, R0.1
0.8
R0.05, R0.1
R0.1, R0.3
1.5
R0.1, R0.2, R0.3
R0.1, R0.2
R0.3, R0.5
3
4
5
6
R0.2, R0.3
R0.5
R0.2, R0.3
R0.5
R0.2, R0.3
R0.5
R0.2, R0.3, R0.5
R1
Neck length
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Revolution
(min-1)
Feed rate
(mm/min)
4
6
6
8
8
10
12
12
20
12
16
20
20
20
20
20
25
25
30
30
40000
40000
40000
40000
40000
35000
30000
30000
20000
30000
30000
20000
20000
20000
15000
15000
12000
12000
10000
10000
800
700
1200
1200
2000
1600
1200
1500
1000
1500
1000
600
2000
2200
2000
2200
1500
1700
1200
1500
0.005
0.003
0.02
0.015
0.03
0.025
0.02
0.05
0.02
0.1
0.06
0.04
0.12
0.12
0.25
0.25
0.3
0.3
0.4
0.4
40000
40000
40000
40000
40000
35000
30000
40000
20000
40000
30000
20000
35000
35000
32000
32000
22000
22000
20000
20000
1500
1000
2500
1600
3000
2000
1800
4500
2000
4500
3000
2000
6000
8000
5000
7000
5000
7000
5000
7000
DC
Depth of cut
Depth of cut
ap
(mm)
ae
(mm)
0.01
0.005
0.02
0.01
0.03
0.025
0.02
0.04
0.02
0.08
0.05
0.04
0.1
0.1
0.15
0.15
0.2
0.2
0.25
0.25
0.1
0.1
0.15
0.15
0.2
0.2
0.2
0.3
0.3
0.4
0.4
0.4
0.6
0.6
0.8
0.8
1.0
1.0
1.2
1.2
TAPER
Dia.
DC (mm)
SOLID END MILLS
Work material
RADIUS

y Slotting
SQUARE
APMX
BALL
RE
Type
DC
Stock
Order Number
No. of Flutes
Unit : mm
< ae
< ap
< ap
DC:Dia.
DC:Dia.
J301
CBN END MILLS
CBN2XLRB
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DN
Hardened Steel
( < 55HRC)
CBN
Aluminium Alloy
B2
SQUARE
DC
Type1
15
APMX
RE
LU
LF
Effective
length
Effective length
for inclined angle
0.05<RE<0.5
0.005
BALL
DCON(h5)
CBN
0.5 < DC < 2

Inclined angle
0
- 0.010
h5
DCON=4
0
- 0.005
a CBN long neck radius end mill. A wide variation of neck lengths available.
DC
APMX
LU
DN
B2
LF
DCON
CBN2XLRBD0050R005N02
0.05
0.05
0.1
0.1
0.05
0.05
0.1
0.1
0.2
0.2
0.3
0.3
0.1
0.1
0.2
0.2
0.3
0.3
0.1
0.1
0.2
0.2
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
0.3
0.3
0.3
0.3
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.9
0.9
0.9
0.9
0.9
0.9
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
2
3
2
3
3
5
3
5
3
5
3
5
5
8
5
8
5
8
6
10
6
10
6
10
6
10
0.46
0.46
0.46
0.46
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.44
1.44
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
11.6
10.4
11.7
10.5
9.7
7.9
9.7
8
9.8
8
9.9
8.1
7.3
5.6
7.3
5.6
7.4
5.7
5.9
4.2
5.9
4.2
6
4.2
6.1
4.3
51
51
51
51
51
51
51
51
51
51
51
51
52
52
52
52
52
52
52
52
52
52
52
52
52
52
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
J302
Type
RE
Stock
Order Number
No. of Flutes
SOLID END MILLS
TAPER
RADIUS
Unit : mm
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
2.1
3.1
2.1
3.1
3.2
5.3
3.2
5.3
3.2
5.3
3.2
5.3
5.3
8.5
5.3
8.5
5.3
8.5
6.3
10.5
6.3
10.5
6.3
10.5
6.3
10.5
2.1
3.2
2.1
3.2
3.4
5.6
3.4
5.6
3.4
5.6
3.4
5.6
5.6
8.8
5.6
8.8
5.6
8.8
6.6
10.9
6.6
10.9
6.6
10.8
6.5
10.8
2.3
3.5
2.3
3.4
3.7
6
3.6
6
3.5
6
3.4
6
6
9.5
6
9.5
6
9.5
7.1
11.7
7.1
11.7
7
11.6
7
11.6
2.5
3.7
2.5
3.7
4
6.5
4
6.5
4
6.5
4
6.5
6.5
10.2
6.5
10.2
6.5
10.2
7.6
12.6
7.6
12.6
7.6
12.6
7.5
12.5
CBN

Work
material
AISI H13
AISI D2
AISI W1, AISI M2
Dia.
DC (mm)
Revolution
(min-1)
0.5
1
1.5
2
50000
38000
25000
20000

(mm/min)
ap (mm)
ae (mm)
(min-1)
750
1100
900
800
0.01
0.02
0.03
0.04
0.2
0.3
0.5
0.7
50000
38000
25000
20000

(mm/min)
ap (mm)
ae (mm)
(min-1)
600
760
700
600
0.01
0.01
0.02
0.03
0.1
0.2
0.4
0.6
40000
25000
17000
12000

(mm/min)
ap (mm)
ae (mm)
400
400
340
300
0.005
0.01
0.02
0.02
0.06
0.1
0.2
0.3
ae
Depth of
cut
ap
DC:Dia.
SOLID END MILLS
2) Oil mist coolant is recommended.
J303
CRN END ALIMASTER

CARBIDE
C3SARB
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
37.5
Copper Alloy
Aluminium Alloy
Type1
RE
DCON(h6)
DC
SQUARE
DN
(<30HRC)
( < 45HRC)
UWC
APMX
LU
DC < 12
0
- 0.020
h6
RE
DC>12
Type2
DCON(h6)
BALL
DC
LF
APMX
LF
0
- 0.030
12<DCON<16 20<DCON<25
0
- 0.011
0
- 0.013
Order Number
DC
RE
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
C3SARBD1200N0300R100
C3SARBD1800R100
C3SARBD1800R320
12
12
12
12
16
16
16
16
18
18
20
20
20
20
20
20
25
25
25
25
25
25
1
3.2
1
3.2
1
3.2
1
3.2
1
3.2
1
3.2
4
1
3.2
4
3.2
4
5
3.2
4
5
15
15
15
15
15
15
15
15
18
18
20
20
20
20
20
20
20
20
20
20
20
20
30
30
40
40
45
45
70
70
60
60
60
85
85
85
65
65
65
90
90
90
11.4
11.4
11.4
11.4
15.4
15.4
15.4
15.4
18.0
18.0
18.0
18.0
18.0
18.0
23.0
23.0
23.0
23.0
23.0
23.0
75
75
125
125
125
125
150
150
150
150
125
125
125
150
150
150
125
125
125
150
150
150
12
12
12
12
16
16
16
16
16
16
20
20
20
20
20
20
25
25
25
25
25
25
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
J304
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
CARBIDE

y Side milling
y Slotting
Work
material
Work
material
Aluminium alloy
Aluminium alloy
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
12
16
18
20
25
13000
10000
9000
8000
6000
5400
5400
5000
5000
4500
12
16
18
20
25
13000
10000
9000
8000
6000
3200
3200
3000
3000
2800
DC
< 0.3DC
Depth of
cut
Depth of
cut
< 0.8DC
DC:Dia.
< 0.5DC
DC:Dia.
SOLID END MILLS

3) This table shows the cutting condition with less than 4D overhang length. If more than 4D, spindle speed, feed rate and depth of cut should
be reduced.
4) These end mills do not have a centre cutting edge, therefore when entering a workpiece use a ramping process rather than vertical feed.
J305
CRN END ALIMASTER

CARBIDE
CSRARB
Corner radius roughing end mill, Short cut length, 3 flute, For aluminium alloy
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
UWC
Copper Alloy
37.5
Aluminium Alloy
DC
SQUARE
DN
DCON(h6)
RE
Type1
APMX
LU
BALL
LF
h6

0
- 0.009
0
- 0.011
0
- 0.013
J306
Order Number
DC
RE
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
CSRARBD1000R100
CSRARBD1000R200
CSRARBD1200R100
CSRARBD1200R200
CSRARBD1600R200
CSRARBD1600R300
CSRARBD2000R200
CSRARBD2000R300
CSRARBD2500R300
CSRARBD2500R400
CSRARBD2500R500
10
10
12
12
16
16
20
20
25
25
25
1
2
1
2
2
3
2
3
3
4
5
12
12
15
15
18
18
25
25
30
30
30
25
25
30
30
35
35
50
50
60
60
60
9.4
9.4
11.4
11.4
15.4
15.4
18.0
18.0
23.0
23.0
23.0
75
75
75
75
100
100
125
125
125
125
125
10
10
12
12
16
16
20
20
25
25
25
3
3
3
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
CARBIDE

y Side milling
Work
material
y Slotting
Aluminium alloy
Aluminium cast
Work
material
Aluminium alloy
Aluminium cast
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
10
12
16
18
20
22
25
19000
16000
12000
10500
9500
8500
7500
8600
8200
7600
7200
7100
6900
6800
9500
8000
6000
5300
4800
4300
3800
3400
3200
3100
2900
2900
2800
2700
10
12
16
18
20
22
25
19000
16000
12000
10500
9500
8500
7500
6800
6500
6100
5800
5700
5500
5400
9500
8000
6000
5300
4800
4300
3800
2700
2600
2400
2400
2300
2200
2200
DC
< 0.5DC
Depth of
cut
Depth of
cut
< 1DC
< 1DC
DC:Dia.
1)
2)
3)
4)
5)
DC:Dia.

Using a high-speed and high-rigidity machining center

y Side milling
Aluminium alloy
Aluminium cast
Work
material
Aluminium alloy
Aluminium cast
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
10
12
16
18
20
22
25
30000
30000
24000
21000
19000
17000
15000
11000
12000
12000
12000
11000
11000
11000
19000
16000
12000
10500
9500
8500
7500
5400
5300
4900
4700
4600
4300
4300
10
12
16
18
20
22
25
30000
30000
24000
21000
19000
17000
15000
8600
9900
9700
9500
9100
8700
8600
19000
16000
12000
10500
9500
8500
7500
4300
4300
4000
3800
3700
3400
3400
DC
< 0.5DC
Depth of
cut
Depth of
cut
< 1DC
DC:Dia.
1)
2)
3)
4)
5)
SOLID END MILLS
Work
material
y Slotting
< 0.75DC
DC:Dia.

J307
MSTAR END MILLS

CARBIDE
MS4MRB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
UWC
Austenitic
Stainless Steel
Titanium Alloy,
MS
Copper Alloy
30
Aluminium Alloy
Type1
RE
DCON(h6)
DC
SQUARE
15
APMX
DC
LF
DC < 12
0
- 0.020
h6
DCON(h6)
BALL
RE
Type2
APMX
LF
DC>12
0
- 0.030

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
J308
Order Number
DC
RE
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
MS4MRBD0300R010
MS4MRBD0300R020
MS4MRBD0300R030
MS4MRBD0300R050
MS4MRBD0300R100
MS4MRBD0400R010
MS4MRBD0400R020
MS4MRBD0400R030
MS4MRBD0400R050
MS4MRBD0400R100
MS4MRBD0500R010
MS4MRBD0500R020
MS4MRBD0500R030
MS4MRBD0500R050
MS4MRBD0500R100
MS4MRBD0600R010
MS4MRBD0600R020
MS4MRBD0600R030
MS4MRBD0600R050
MS4MRBD0600R100
MS4MRBD0600R150
MS4MRBD0600R200
MS4MRBD0800R020
MS4MRBD0800R030
MS4MRBD0800R050
MS4MRBD0800R100
MS4MRBD0800R150
MS4MRBD0800R200
MS4MRBD0800R250
MS4MRBD0800R300
MS4MRBD1000R020
MS4MRBD1000R030
MS4MRBD1000R050
MS4MRBD1000R100
3
3
3
3
3
4
4
4
4
4
5
5
5
5
5
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
10
10
10
10
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
0.1
0.2
0.3
0.5
1
1.5
2
0.2
0.3
0.5
1
1.5
2
2.5
3
0.2
0.3
0.5
1
8
8
8
8
8
11
11
11
11
11
13
13
13
13
13
13
13
13
13
13
13
13
19
19
19
19
19
19
19
19
22
22
22
22
45
45
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
50
60
60
60
60
60
60
60
60
70
70
70
70
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
10
10
10
10
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
CARBIDE
DCON
Stock
MS4MRBD1000R150
MS4MRBD1000R200
MS4MRBD1000R250
MS4MRBD1000R300
MS4MRBD1200R020
MS4MRBD1200R030
MS4MRBD1200R050
MS4MRBD1200R100
MS4MRBD1200R150
MS4MRBD1200R200
MS4MRBD1200R250
MS4MRBD1200R300
MS4MRBD1600R050
MS4MRBD1600R100
MS4MRBD1600R150
MS4MRBD1600R200
MS4MRBD1600R250
MS4MRBD1600R300
MS4MRBD2000R050
MS4MRBD2000R100
MS4MRBD2000R150
MS4MRBD2000R200
MS4MRBD2000R250
MS4MRBD2000R300
10
10
10
10
12
12
12
12
12
12
12
12
16
16
16
16
16
16
20
20
20
20
20
20
1.5
2
2.5
3
0.2
0.3
0.5
1
1.5
2
2.5
3
0.5
1
1.5
2
2.5
3
0.5
1
1.5
2
2.5
3
22
22
22
22
26
26
26
26
26
26
26
26
32
32
32
32
32
32
38
38
38
38
38
38
70
70
70
70
75
75
75
75
75
75
75
75
90
90
90
90
90
90
100
100
100
100
100
100
10
10
10
10
12
12
12
12
12
12
12
12
16
16
16
16
16
16
20
20
20
20
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
SQUARE
LF
BALL
APMX
RADIUS
RE
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J309
MSTAR END MILLS

CARBIDE
MS4MRB
Work
material


Pre-hardened steel

Titanium alloy
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
1
1.5
2
2.5
3
4
5
6
8
10
12
16
20
40000
32000
24000
19000
16000
12000
9600
8000
6000
4800
4000
3000
2400
1500
1500
1500
1500
1500
1800
1800
1800
1600
1400
1200
960
800
30000
20000
15000
12000
10000
8000
6400
5300
4000
3200
2700
2000
1600
800
800
800
800
800
1000
1000
1000
900
800
700
560
480
22000
15000
11000
8800
7400
5600
4400
3700
2800
2200
1800
1400
1100
480
480
480
480
480
600
600
600
560
500
430
360
300
24000
16000
12000
9600
8000
6000
4800
4000
3000
2400
2000
1500
1200
240
240
240
240
240
240
240
240
240
240
230
190
170
<0.05DC
<1DC
<0.1DC
Depth of
cut
DC
<1.5DC
0.1DC
DC
SOLID END MILLS
<0.05DC
J310
DC:Dia.
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
0.2<RE<6.35
RE
APMX
0
- 0.020
h6
DC
DC>12
0
- 0.030
RE

0
- 0.008
0
- 0.009
0
- 0.011
APMX
Type2
Type3
LF
0.020
DC < 12
Type1
LF
DC
RE
APMX
SQUARE
Austenitic
Stainless Steel
CARBIDE
LF
BALL
Hardened Steel
(>55HRC)
45
DCON(h6)
Hardened Steel
( < 55HRC)
MS
DCON(h6)
(<30HRC)
( < 45HRC)
UWC
DCON(h6)
MSMHDRB
0
- 0.013
RE
APMX
LF
DCON
Stock
MSMHDRBD0200R020
MSMHDRBD0200R030
MSMHDRBD0300R020
MSMHDRBD0300R030
MSMHDRBD0300R050
MSMHDRBD0400R020
MSMHDRBD0400R030
MSMHDRBD0400R050
MSMHDRBD0500R020
MSMHDRBD0500R030
MSMHDRBD0500R050
MSMHDRBD0500R100
MSMHDRBD0600R030
MSMHDRBD0600R050
MSMHDRBD0600R100
MSMHDRBD0800R030
MSMHDRBD0800R050
MSMHDRBD0800R100
MSMHDRBD0800R150
MSMHDRBD1000R030
MSMHDRBD1000R050
MSMHDRBD1000R100
MSMHDRBD1000R150
MSMHDRBD1000R200
MSMHDRBD1200R050S10
MSMHDRBD1200R100S10
MSMHDRBD1200R150S10
MSMHDRBD1200R200S10
MSMHDRBD1200R300S10
MSMHDRBD1200R050
MSMHDRBD1200R100
MSMHDRBD1200R150
MSMHDRBD1200R200
MSMHDRBD1200R300
2
2
3
3
3
4
4
4
5
5
5
5
6
6
6
8
8
8
8
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
0.2
0.3
0.2
0.3
0.5
0.2
0.3
0.5
0.2
0.3
0.5
1
0.3
0.5
1
0.3
0.5
1
1.5
0.3
0.5
1
1.5
2
0.5
1
1.5
2
3
0.5
1
1.5
2
3
4
4
8
8
8
11
11
11
13
13
13
13
13
13
13
19
19
19
19
22
22
22
22
22
26
26
26
26
26
26
26
26
26
26
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
60
60
60
60
70
70
70
70
70
75
75
75
75
75
75
75
75
75
75
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
2
2
2
2
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 4 flute high power corner radius end mill.
J311
MSTAR END MILLS
MSMHDRB
DC
RE
APMX
LF
DCON
No. of
Flutes
Stock
MSMHDRBD1600R100
MSMHDRBD1600R150
MSMHDRBD1600R200
MSMHDRBD1600R300
MSMHDRBD1600R500
MSMHDRBD1800R100
MSMHDRBD1800R150
MSMHDRBD1800R200
MSMHDRBD1800R300
MSMHDRBD2000R100
MSMHDRBD2000R150
MSMHDRBD2000R200
MSMHDRBD2000R300
MSMHDRBD2000R500
MSMHDRBD2000R635
16
16
16
16
16
18
18
18
18
20
20
20
20
20
20
1
1.5
2
3
5
1
1.5
2
3
1
1.5
2
3
5
6.35
35
35
35
35
35
40
40
40
40
45
45
45
45
45
45
90
90
90
90
90
100
100
100
100
110
110
110
110
110
110
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
SOLID END MILLS
J312
Unit : mm
Order Number
TAPER
RADIUS
BALL
SQUARE
CARBIDE
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
2
2
2
2
3
3
3
3
2
2
2
2
2
2
CARBIDE

y Side milling
material
AISI P20

Pre-hardened steel

Titanium alloy

AISI P21
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
8
10
12
16
18
20
15000
11000
8000
6400
5900
4400
3500
2900
2200
2000
1800
550
800
900
1000
1100
1100
1000
1000
800
800
750
10000
7400
5600
4500
3700
2800
2300
1900
1400
1250
1100
340
500
540
600
640
660
640
640
500
480
460
10000
7400
5600
4500
3700
2800
2300
1900
1400
1250
1100
320
480
520
580
600
600
560
530
450
450
440
6400
4800
3600
2900
2400
1800
1400
1200
900
800
720
160
250
270
300
320
330
320
320
250
240
230
4800
4000
3200
2600
2100
1600
1300
1100
800
710
650
100
170
240
240
230
220
200
170
130
110
100
Depth of
cut
<0.2DC
<0.1DC
<0.05DC
<1.5DC
<1.5DC
<1.5DC
DC:Dia.
y Slotting

Pre-hardened steel

Titanium alloy

AISI P21
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
8
10
12
16
18
20
12000
9000
7200
5800
5000
3700
3000
2500
2000
1800
1600
400
600
720
720
800
800
720
600
480
460
430
7000
5300
4000
3200
2700
2000
1600
1300
1000
900
800
200
300
360
360
400
400
360
290
230
210
200
7000
5300
4000
3200
2700
2000
1600
1300
1000
900
800
100
150
180
180
200
200
180
150
120
110
100
4200
3200
2400
1900
1600
1200
960
800
600
550
480
80
130
140
150
160
170
160
140
110
110
100
2300
1900
1400
1100
950
720
570
480
360
320
290
40
70
95
95
95
90
80
70
50
45
40
DC
Depth of
cut
DC
<1DC
(MAX. 12mm)
SOLID END MILLS

material
AISI P20
DC
<0.5DC
<0.2DC
DC:Dia.
J313
VFFDRB
NEW
Copper Alloy
Xb
Rb
APMX
LE
LU
Ra
Aluminium Alloy
15
BALL
DC
DN
APMX
LE
LU
DC < 12
0
- 0.020
Type2
LF
h6
0
- 0.008
0
- 0.009
0
- 0.011
a Multi-task corner radius type allows more efficient high feed.

a Adoption of multiple cuttings realized high feed cutting.
DC
* APMX LE*
RE
VFFDRBD0300
VFFDRBD0400
VFFDRBD0600
VFFDRBD0800
VFFDRBD1000
VFFDRBD1200
3
4
6
8
10
12
0.64
0.71
0.92
1.16
1.47
1.77
0.18
0.25
0.36
0.44
0.57
0.7
3
4
9
12
15
18
LU
DN
LF DCON
10
12
18
24
30
36
2.8
3.8
5.6
7.6
9.4
11.4
60
60
80
90
100
110
6
6
6
8
10
12
Xb
Ra
Rb
0.08
0.13
0.21
0.22
0.28
0.34
0.375
0.5
0.75
1.6
2
2.4
0.5
0.5
0.6
0.8
1
1.2
2
3
5
4.5
5.5
6.5
2.1
1.9
1.7
1.7
1.7
1.8
Multi-task radius part
No. of
Flutes
Order Number
4
4
4
6
6
6
Stock
Unit : mm
*
RMPX
TAPER
RADIUS
Type1
LF
RE
SOLID END MILLS
DC8
DCON(H6)
DC6
Titanium Alloy,
Austenitic
Stainless Steel
DCON(H6)
Hardened Steel
(>55HRC)
SQUARE
Hardened Steel
( < 55HRC)
40
DN
(<30HRC)
( < 45HRC)
VF
UWC
DC
CARBIDE
a
a
a
a
a
a
Type
1
1
2
2
2
2
: Approx. R
*12 RE
RMPX : Max. Ramping Angle
*3 LE : Cutting Edge Effective Length
*
RECOMMENDED CUTTING CONDITIONS FOR IMPACT MIRACLE END MILLS

y Side milling
Carbon steel, Alloy steel (180280HB),
Work Alloy tool steel (350HB),
material Mild steel (180HB)
AISI 1045, AISI 4140, ASTM A36, AISI 1010
Prehardened steel (3545HRC)
AISI P21, AISI P20, AISI 4340
Dia. Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of cut Depth of cut Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of cut Depth of cut
Revolution
Revolution
per Min.
per Min.
DC (mm) (m/min)
(mm/t.)
ap (mm)
ae (mm)
(m/min)
(mm/t.)
ap (mm)
ae (mm)
(min-1)
(min-1)
(mm/min)
(mm/min)
4
6
8
10
12
150
150
150
150
150
150
16000
12000
8000
6000
4800
4000
0.15
0.20
0.35
0.35
0.40
0.45
9600
9600
11000
13000
12000
11000
0.12
0.16
0.24
0.32
0.40
0.48
1.5
2.0
3.0
4.8
6.0
7.2
135
135
135
135
135
135
14000
11000
7200
5400
4300
3600
0.15
0.20
0.35
0.35
0.40
0.45
8400
8800
10000
11000
10000
9700
0.12
0.16
0.24
0.32
0.40
0.48
1.5
2.0
3.0
4.8
6.0
7.2
Hardened steel (5562HRC)
Hardened steel (4055HRC),

Work Ferritic and martensitic stainless steel (>200HB),
material Precipitation hardening stainless steel (<450HB),
AISI H13, L6, AISI 431, AISI 420, 15-5PH, 17-4PH etc.
AISI D2 etc.
Dia. Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of cut Depth of cut Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of cut Depth of cut
Revolution
Revolution
per Min.
per Min.
DC (mm) (m/min)
(mm/t.)
ap (mm)
ae (mm)
(m/min)
(mm/t.)
ap (mm)
ae (mm)
(min-1)
(min-1)
(mm/min)
(mm/min)
4
6
8
10
12
120
120
120
120
120
120
13000
9500
6400
4800
3800
3200
0.15
0.21
0.35
0.35
0.40
0.45
7800
8000
9000
10000
9100
8600
0.12
0.16
0.24
0.32
0.40
0.48
1.5
2.0
3.0
4.8
6.0
7.2
80
80
80
80
80
80
8500
6400
4200
3200
2500
2100
1) When ramping process set the feedrate at 50%. A ramping angle of 1 is recommended.
2) Use at a revolution of 70% and feedrate of 50% when the tool overhang exceeds 5D.
a
J314
0.10
0.15
0.30
0.30
0.35
0.40
3400
3800
5000
5800
5300
5000
0.12
0.16
0.24
0.32
0.40
0.48
1.5
2.0
3.0
4.8
6.0
7.2
DC:Dia.
4 FLUTE, CORNER RADIUS, SHORT CUT LENGTH,IRREGULAR HELIX FLUTES
0.007
0.01
DC < 12
DC>12

0
- 0.008
0
- 0.009
DN
DC
RE
APMX
LU
Type1
Type2
Type3
LF
Inclined angle
0
- 0.03
15
LF
DC
0
- 0.02
h6
DC>10
Effective
length
DC < 10
Aluminium Alloy
B2
APMX
LU
RE
Effective length
for inclined angle
Copper Alloy
RE
0
- 0.011
APMX
LF
SQUARE
BALL
Titanium Alloy,
DCON(h6)
Austenitic
Stainless Steel
CARBIDE
DCON(h6)
Hardened Steel
(>55HRC)
DC
Hardened Steel
( < 55HRC)
43
45
DN
(<30HRC)
( < 45HRC)
VF
UWC
DCON(h6)
VFHVRB
LU
DN
B2
LF
DCON
VFHVRBD0100R02N004
VFHVRBD0100R02N006
VFHVRBD0100R02N008
VFHVRBD0100R02N010
VFHVRBD0100R02N015
VFHVRBD0100R02N020
VFHVRBD0150R03N004
VFHVRBD0150R03N006
VFHVRBD0150R03N010
VFHVRBD0150R03N015
VFHVRBD0150R03N020
VFHVRBD0150R03N025
VFHVRBD0150R03N030
VFHVRBD0200R05N006
VFHVRBD0200R05N010
VFHVRBD0200R05N015
VFHVRBD0200R05N020
VFHVRBD0200R05N025
VFHVRBD0200R05N030
VFHVRBD0200R05N035
VFHVRBD0200R05N040
VFHVRBD0300R05N010
VFHVRBD0300R05N015
VFHVRBD0300R05N020
VFHVRBD0300R05N030
VFHVRBD0300R08N010
VFHVRBD0300R08N015
VFHVRBD0300R08N020
VFHVRBD0300R08N030
VFHVRBD0300R08N040
VFHVRBD0300R08N050
VFHVRBD0400R05N012
VFHVRBD0400R05N020
VFHVRBD0400R05N030
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
0.8
0.8
0.5
0.5
0.5
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
6
8
10
15
20
4
6
10
15
20
25
30
6
10
15
20
25
30
35
40
10
15
20
30
10
15
20
30
40
50
12
20
30
0.94
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.44
1.44
1.44
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
3.9
3.9
3.9
10.6
9.2
8.2
7.4
5.9
4.9
10.3
8.9
7
5.5
4.6
3.9
3.4
8.7
6.7
5.2
4.3
3.6
3.1
2.8
2.5
5.6
4.3
3.4
2.5
5.7
4.3
3.5
2.5
2
1.6
3.8
2.5
1.8
60
60
60
60
60
80
60
60
60
60
80
80
80
60
60
60
80
80
80
90
90
60
60
80
80
60
60
80
80
90
90
60
80
80
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
4.2
6.4
8.5
10.5
15.8
20.9
4.2
6.3
10.5
15.7
20.9
26.1
31.3
6.3
10.5
15.6
20.8
26
31.2
36.3
41.5
10.5
15.6
20.8
31.2
10.4
15.6
20.8
31.1
41.5
51.8
12.5
20.8
31.2
4.5
6.7
8.8
11
16.3
21.7
4.5
6.6
10.9
16.3
21.6
27
32.3
6.5
10.8
16.2
21.5
26.9
32.2
37.6
42.9
10.8
16.2
21.5
32.2
10.8
16.2
21.5
32.2
42.9
53.6
13
21.5
32.2
4.7
7.2
9.5
11.8
17.5
23.3
4.6
7.2
11.8
17.5
23.3
29
34.7
7
11.6
17.4
23.1
28.9
34.6
40.4
46.1
11.6
17.4
23.1
34.6
11.6
17.3
23.1
34.6
5.3
7.7
10.2
12.7
18.9
25.1
5.2
7.7
12.7
18.9
25.1
31.3
37.5
7.5
12.5
18.7
24.9
31.2
37.4
TAPER
APMX
SOLID END MILLS
RE
Type
DC
Stock
Order Number
No. of Flutes
Unit : mm
RADIUS
a Impact Miracle corner radius end mill for high feed and efficient machining.
*
*
12.5
18.7
24.9
12.4
18.7
24.9
*
* *
* *
13.9 15
*
*
*
No interference
23.1
J315
VFHVRB
J316
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
7
8
8
8
8
8
8
8
8
9
10
10
10
10
10
10
10
10
11
12
12
12
12
12
12
12
12
12
12
13
16
16
16
16
16
RE
0.5
1
1
1
0.5
0.5
1
1
1
1.5
1.5
1.5
1.5
2
2
1.5
0.5
0.5
1
1
2
2
2
2
2
0.5
0.5
1
1
2
2
2
2
2
0.5
0.5
1
1
2
2
2
2
3
3
3
0.5
2
3
3
3
APMX
LU
DN
4
4
4
4
9
9
9
9
9
9
9
9
9
9
9
11
12
12
12
12
12
12
12
12
13.5
15
15
15
15
15
15
15
15
16.5
18
18
18
18
18
18
18
18
18
18
19.5
24
24
24
24
24
48
12
20
30
18
30
18
30
54
18
30
42
54
18
30
24
40
24
40
24
40
56
72
30
50
30
50
30
50
70
90
36
60
36
60
36
60
84
108
36
60
42
42
42
80
120
3.9
3.9
3.9
3.9
5.85
5.85
5.85
5.85
5.85
5.85
5.85
5.85
5.85
5.85
5.85
7.85
7.85
7.85
7.85
7.85
7.85
7.85
7.85
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
15.5
15.5
15.5
15.5
15.5
B2
LF
DCON
1.2
3.9
2.5
1.8
90
60
80
80
60
80
60
80
90
60
80
90
90
60
80
80
60
100
60
100
60
100
120
120
100
70
110
70
110
70
110
150
150
110
80
120
80
120
80
120
160
160
80
120
120
100
100
100
140
175
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
16
16
16
16
16
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Type
VFHVRBD0400R05N048
VFHVRBD0400R10N012
VFHVRBD0400R10N020
VFHVRBD0400R10N030
VFHVRBD0600R05N018
VFHVRBD0600R05N030
VFHVRBD0600R10N018
VFHVRBD0600R10N030
VFHVRBD0600R10N054
VFHVRBD0600R15N018
VFHVRBD0600R15N030
VFHVRBD0600R15N042
VFHVRBD0600R15N054
VFHVRBD0600R20N018
VFHVRBD0600R20N030
VFHVRBD0700R15
VFHVRBD0800R05N024
VFHVRBD0800R05N040
VFHVRBD0800R10N024
VFHVRBD0800R10N040
VFHVRBD0800R20N024
VFHVRBD0800R20N040
VFHVRBD0800R20N056
VFHVRBD0800R20N072
VFHVRBD0900R20
VFHVRBD1000R05N030
VFHVRBD1000R05N050
VFHVRBD1000R10N030
VFHVRBD1000R10N050
VFHVRBD1000R20N030
VFHVRBD1000R20N050
VFHVRBD1000R20N070
VFHVRBD1000R20N090
VFHVRBD1100R20
VFHVRBD1200R05N036
VFHVRBD1200R05N060
VFHVRBD1200R10N036
VFHVRBD1200R10N060
VFHVRBD1200R20N036
VFHVRBD1200R20N060
VFHVRBD1200R20N084
VFHVRBD1200R20N108
VFHVRBD1200R30N036
VFHVRBD1200R30N060
VFHVRBD1300R30
VFHVRBD1600R05N042
VFHVRBD1600R20N042
VFHVRBD1600R30N042
VFHVRBD1600R30N080
VFHVRBD1600R30N120
DC
Stock
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
Order Number
Unit : mm
No. of Flutes
CARBIDE
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
3
2
2
2
2
2
2
2
2
3
2
2
2
2
2
2
2
2
3
2
2
2
2
2
2
2
2
2
2
3
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
49.8
12.5
20.8
31.1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
51.5
12.9 13.8 14.9
21.5 23
32.2
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* No interference
CARBIDE

y High speed milling
Work material


Pre-hardened steel

AISI P20
AISI H13
AISI D2
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
0.8
0.8
0.5
0.5
0.5
0.5
1
1
1
0.5
0.5
1
1
1
1.5
1.5
1.5
1.5
2
2
4
6
8
10
15
20
4
6
10
15
20
25
30
6
10
15
20
25
30
35
40
10
15
20
30
10
15
20
30
40
50
12
20
30
48
12
20
30
18
30
18
30
54
18
30
42
54
18
30
40000
40000
32000
24000
16000
14000
32000
32000
27000
22000
16000
13000
13000
24000
24000
20000
20000
16000
16000
13000
13000
16000
16000
13000
13000
16000
16000
13000
13000
11000
8000
8400
8400
6900
5600
12000
12000
10000
4000
4000
8000
8000
6600
8000
8000
6600
6600
8000
8000
7200
6500
4500
2700
1200
1000
10000
7800
5700
3200
1400
1000
900
10000
10000
7000
3600
1800
1400
1100
1000
11000
9000
7200
5700
11000
9000
7200
5700
3600
2600
6000
6000
4900
2000
12000
12000
9900
3900
3900
13000
13000
11000
13000
13000
11000
11000
13000
13000
0.04
0.03
0.022
0.015
0.008
0.005
0.1
0.08
0.05
0.03
0.02
0.015
0.01
0.1
0.08
0.05
0.04
0.03
0.025
0.02
0.02
0.12
0.11
0.09
0.06
0.24
0.22
0.19
0.12
0.08
0.07
0.15
0.14
0.12
0.07
0.3
0.27
0.24
0.15
0.14
0.5
0.45
0.25
0.5
0.45
0.4
0.25
0.5
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1.5
1.5
1.5
1.5
1
1
1
1
1
1
2
2
2
2
1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
33000
33000
27000
20000
14000
12000
27000
27000
22000
18000
14000
11000
11000
20000
20000
17000
17000
14000
14000
11000
11000
13000
13000
11000
11000
13000
13000
11000
11000
9100
6600
7000
7000
5700
4600
10000
10000
8300
3300
3300
6600
6600
5500
6600
6600
5500
5500
6600
6600
5100
4600
3200
1900
700
600
7100
5500
4000
2300
1200
800
700
7100
7100
5000
2600
1400
1200
800
700
7800
6400
5100
4000
7800
6400
5100
4000
2600
1800
4300
4300
3500
1400
8500
8500
7000
2800
2800
9200
9200
7800
9200
9200
7800
7800
9200
9200
0.03
0.022
0.018
0.01
0.005
0.004
0.08
0.06
0.035
0.025
0.016
0.012
0.008
0.08
0.06
0.04
0.03
0.025
0.02
0.018
0.015
0.09
0.08
0.07
0.05
0.19
0.17
0.15
0.09
0.06
0.05
0.12
0.11
0.09
0.05
0.23
0.21
0.19
0.12
0.11
0.4
0.35
0.2
0.4
0.35
0.3
0.2
0.4
0.35
0.45
0.45
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1.5
1.5
1.5
1.5
1
1
1
1
1
1
2
2
2
2
1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
27000
27000
21000
16000
12000
10000
21000
21000
18000
15000
13000
10000
10000
16000
16000
13000
13000
12000
12000
10000
10000
11000
11000
8700
8700
11000
11000
8700
8700
7400
5800
5600
5600
4600
3800
8000
8000
6700
2700
2700
5400
5400
4400
5400
5400
4400
4400
5400
5400
4100
3700
2600
1500
500
400
5700
4200
3000
1700
1000
700
600
5700
5700
3200
1800
1100
900
700
600
6300
5100
4000
3000
6300
5100
4000
3000
2000
1500
3400
3400
2800
1100
6800
6800
5600
2200
2200
7400
7400
6300
7400
7400
6300
6300
7400
7400
0.025
0.018
0.012
0.008
0.003
0.002
0.06
0.05
0.03
0.018
0.012
0.009
0.006
0.06
0.05
0.03
0.025
0.02
0.016
0.014
0.012
0.07
0.06
0.05
0.04
0.14
0.13
0.11
0.07
0.05
0.04
0.09
0.08
0.07
0.04
0.18
0.16
0.14
0.09
0.08
0.3
0.27
0.15
0.3
0.27
0.24
0.15
0.3
0.27
0.45
0.45
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1.5
1.5
1.5
1.5
1
1
1
1
1
1
2
2
2
2
1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
20000
20000
16000
12000
10000
9000
16000
16000
14000
11000
9000
7500
7500
12000
12000
10000
10000
9000
9000
7000
7000
8000
8000
6500
6500
8000
8000
6500
6500
5500
4600
4200
4200
3500
2800
6000
6000
5000
2000
2000
4000
4000
3300
4000
4000
3300
3300
4000
4000
1800
1600
1100
700
400
300
2500
2000
1400
1000
700
500
400
2500
2500
1800
900
720
650
500
400
2800
2300
1800
1400
2800
2300
1800
1400
1000
800
1500
1500
1200
500
3000
3000
2500
1000
1000
3300
3300
2800
3300
3300
2800
2800
3300
3300
0.013
0.01
0.008
0.006
0.003
0.002
0.03
0.025
0.014
0.009
0.007
0.005
0.004
0.03
0.025
0.016
0.012
0.01
0.008
0.007
0.006
0.04
0.04
0.03
0.02
0.07
0.07
0.06
0.04
0.025
0.02
0.05
0.04
0.03
0.02
0.1
0.08
0.07
0.05
0.04
0.15
0.14
0.08
0.15
0.14
0.12
0.08
0.15
0.14
0.45
0.45
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1.5
1.5
1.5
1.5
1
1
1
1
1
1
2
2
2
2
1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
SOLID END MILLS
Dia. Corner R Neck Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut
length
DC (mm) RE (mm) LU (mm) (min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm)
ae
Depth of cut
ap
J317

CARBIDE
VFHVRB
Work material


Pre-hardened steel

AISI P20
AISI H13
AISI D2
SOLID END MILLS
length
7
8
8
8
8
8
8
8
8
9
10
10
10
10
10
10
10
10
11
12
12
12
12
12
12
12
12
12
12
13
16
16
16
16
16
1.5 6800 13000 0.5

0.5
24 3000 3900 0.18
0.5
40 3000 3900 0.16
1
24 4200 6500 0.3
1
40 4200 6500 0.27
2
24 6000 13000 0.6
2
40 6000 13000 0.54
2
56 5000 11000 0.48
2
72 5000 11000 0.3
2
5300 13000 0.6
0.5
30 2400 3900 0.18
0.5
50 2400 3900 0.16
1
30 3300 6500 0.3
1
50 3300 6500 0.27
2
30 4800 13000 0.6
2
50 4800 13000 0.54
2
70 4000 11000 0.48
2
90 4000 11000 0.48
2
4300 12000 0.6
0.5
36 2000 3600 0.27
0.5
60 2000 3600 0.24
1
36 2400 4800 0.36
1
60 2400 4800 0.32
2
36 4000 12000 0.9
2
60 4000 12000 0.8
2
84 3300 9900 0.7
2
108 3300 9900 0.45
3
36 4000 12000 0.9
3
60 4000 12000 0.8
3
3700 12000 0.9
0.5
42 1500 3000 0.27
2
42 2100 5000 0.45
3
42 3000 10000 0.9
3
80 3000 10000 0.8
3
120 2500 8300 0.7
3
5
5
4.5
4.5
3
3
3
3
3.5
6.5
6.5
6
6
4.5
4.5
4.5
4.5
5
8
8
7.5
7.5
6
6
6
6
4.5
4.5
5
11
9
7.5
7.5
7.5
5600
2500
2500
3500
3500
5000
5000
4200
4200
4400
2000
2000
2700
2700
4000
4000
3300
3300
3600
1700
1700
2000
2000
3300
3300
2700
2700
3300
3300
3100
1200
1700
2500
2500
2100
9200
2800
2800
4600
4600
9200
9200
7800
7800
9200
2800
2800
4600
4600
9200
9200
7800
7800
8500
2600
2600
3400
3400
8500
8500
7000
7000
8500
8500
8500
2100
3600
7100
7100
5900
0.4
0.14
0.12
0.23
0.21
0.46
0.42
0.37
0.23
0.46
0.14
0.12
0.23
0.21
0.46
0.42
0.37
0.37
0.46
0.21
0.18
0.28
0.25
0.7
0.6
0.55
0.35
0.7
0.6
0.7
0.21
0.35
0.7
0.6
0.55
3
5
5
4.5
4.5
3
3
3
3
3.5
6.5
6.5
6
6
4.5
4.5
4.5
4.5
5
8
8
7.5
7.5
6
6
6
6
4.5
4.5
5
11
9
7.5
7.5
7.5
4600
2000
2000
2800
2800
4000
4000
3400
3400
3600
1600
1600
2200
2200
3200
3200
2700
2700
2900
1300
1300
1600
1600
2700
2700
2200
2200
2700
2700
2500
1000
1400
2000
2000
1700
7400
2200
2200
3700
3700
7400
7400
6300
6300
7400
2200
2200
3700
3700
7400
7400
6300
6300
6800
2100
2100
2700
2700
6800
6800
5600
5600
6800
6800
6800
1700
2900
5700
5700
4700
0.3
0.11
0.1
0.18
0.16
0.36
0.32
0.3
0.2
0.36
0.11
0.1
0.18
0.16
0.36
0.32
0.3
0.3
0.36
0.14
0.12
0.18
0.16
0.45
0.4
0.36
0.23
0.45
0.4
0.45
0.12
0.2
0.4
0.37
0.32
3
5
5
4.5
4.5
3
3
3
3
3.5
6.5
6.5
6
6
4.5
4.5
4.5
4.5
5
8
8
7.5
7.5
6
6
6
6
4.5
4.5
5
11
9
7.5
7.5
7.5
3400
1500
1500
2100
2100
3000
3000
2500
2500
2700
1200
1200
1700
1700
2400
2400
2000
2000
2200
1000
1000
1200
1200
2000
2000
1700
1700
2000
2000
1900
750
1100
1500
1500
1300
3300
1000
1000
1600
1600
3300
3300
2800
2800
3300
1000
1000
1600
1600
3300
3300
2800
2800
3000
900
900
1200
1200
3000
3000
2500
2500
3000
3000
3000
750
1300
2500
2500
2100
0.15
0.05
0.05
0.09
0.08
0.18
0.16
0.14
0.09
0.18
0.05
0.05
0.09
0.08
0.18
0.16
0.14
0.14
0.18
0.07
0.06
0.09
0.08
0.23
0.2
0.18
0.11
0.23
0.2
0.23
0.05
0.08
0.15
0.14
0.12
3
5
5
4.5
4.5
3
3
3
3
3.5
6.5
6.5
6
6
4.5
4.5
4.5
4.5
5
8
8
7.5
7.5
6
6
6
6
4.5
4.5
5
11
9
7.5
7.5
7.5
ae
Depth of cut
ap
J318
CARBIDE
y High depth of cut conditions
Work material


Pre-hardened steel

AISI P20
AISI H13
AISI D2
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
0.8
0.8
0.5
0.5
0.5
0.5
1
1
1
0.5
0.5
1
1
1
1.5
1.5
1.5
1.5
2
2
4
6
8
10
15
20
4
6
10
15
20
25
30
6
10
15
20
25
30
35
40
10
15
20
30
10
15
20
30
40
50
12
20
30
48
12
20
30
18
30
18
30
54
18
30
42
54
18
30
24000
24000
19000
14000
19000
19000
16000
13000
14000
14000
12000
12000
9600
9600
7800
7800
9600
9600
7800
7800
5000
5000
4100
7200
7200
6000
2400
2400
4800
4800
4000
4800
4800
4000
4000
4800
4800
2200
2000
1400
800
3000
2300
1700
1000
3000
3000
2100
1100
3300
2700
2200
1700
3300
2700
2200
1700
1800
1800
1500
3600
3600
3000
1200
1200
3900
3900
3300
3900
3900
3300
3300
3900
3900
0.08
0.07
0.05
0.04
0.2
0.16
0.1
0.06
0.2
0.16
0.1
0.08
0.24
0.22
0.18
0.12
0.5
0.5
0.4
0.24
0.3
0.3
0.24
0.6
0.6
0.5
0.3
0.3
1
0.9
0.5
1
0.9
0.8
0.5
1
0.9
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
1.5
1.5
1.5
1.5
1
1
1
1
2
2
2
1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
20000
20000
16000
12000
16000
16000
13000
11000
12000
12000
10000
10000
8000
8000
6500
6500
8000
8000
6500
6500
4200
4200
3400
6000
6000
5000
2000
2000
4000
4000
3300
4000
4000
3300
3300
4000
4000
1500
1400
1000
600
2100
1600
1200
700
2100
2100
1500
800
2300
1900
1500
1200
2300
1900
1500
1200
1300
1300
1100
2500
2500
2100
840
840
2700
2700
2300
2700
2700
2300
2300
2700
2700
0.07
0.05
0.04
0.03
0.16
0.13
0.07
0.05
0.16
0.13
0.08
0.06
0.2
0.17
0.14
0.1
0.4
0.35
0.3
0.2
0.24
0.22
0.19
0.5
0.4
0.4
0.24
0.22
0.8
0.7
0.4
0.8
0.7
0.6
0.4
0.8
0.7
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
1.5
1.5
1.5
1.5
1
1
1
1
2
2
2
1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
16000
16000
13000
9000
13000
13000
11000
9000
9400
9400
8000
8000
6400
6400
5200
5200
6400
6400
5200
5200
3400
3400
2700
4800
4800
4000
1600
1600
3200
3200
2700
3200
3200
2700
2700
3200
3200
1200
1100
800
400
1700
1300
1000
600
1700
1700
1200
600
1800
1500
1200
1000
1800
1500
1200
1000
1000
1000
840
2000
2000
1700
670
670
2200
2200
1800
2200
2200
1800
1800
2200
2200
0.05
0.04
0.03
0.025
0.12
0.1
0.05
0.04
0.12
0.1
0.06
0.05
0.14
0.13
0.11
0.07
0.3
0.25
0.23
0.14
0.18
0.17
0.14
0.36
0.32
0.3
0.18
0.17
0.6
0.5
0.3
0.6
0.5
0.5
0.3
0.6
0.5
0.45 12000 550

0.45 12000 500
0.45 9500 350
0.45 7000 200
0.65 9500 750

0.65 9500 580
0.65 8000 430
0.65 6500 250
0.75 7000 750

0.75 7000 750
0.75 6000 530
0.75 6000 280
1.5
4800 830
1.5
4800 680
1.5
3900 550
1.5
3900 430
1
4800 830
1
4800 680
1
3900 550
1
3900 430
2
2500 450
2
2500 450
2
2100 380
1.5
3600 900
1.5
3600 900
1.5
3000 750
3.5
1200 300
3.5
1200 300
3
2400 980
3
2400 980
3
2000 830
2
2400 980
2
2400 980
2
2000 830
2
2000 830
1.5
2400 980
1.5
2400 980
0.025
0.02
0.016
0.012
0.06
0.05
0.03
0.018
0.06
0.05
0.03
0.025
0.07
0.06
0.05
0.04
0.14
0.13
0.11
0.05
0.06
0.06
0.05
0.12
0.11
0.1
0.06
0.06
0.2
0.18
0.1
0.2
0.18
0.16
0.1
0.2
0.18
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
1.5
1.5
1.5
1.5
1
1
1
1
2
2
2
1.5
1.5
1.5
3.5
3.5
3
3
3
2
2
2
2
1.5
1.5
SOLID END MILLS
length
ae
Depth of cut
ap
J319

CARBIDE
VFHVRB
Work material


Pre-hardened steel

AISI P20
AISI H13
AISI D2
SOLID END MILLS
length
7
8
8
8
8
8
8
8
8
9
10
10
10
10
10
10
10
10
11
12
12
12
12
12
12
12
12
12
12
13
16
16
16
16
16
1.5 4100 3900

0.5
24 1800 1200
0.5
40 1800 1200
1
24 2500 2000
1
40 2500 2000
2
24 3600 3900
2
40 3600 3900
2
56 3000 3300
2
72 3000 3300
2
3200 3900
0.5
30 1400 1200
0.5
50 1400 1200
1
30 2000 2000
1
50 2000 2000
2
30 2900 3900
2
50 2900 3900
2
70 2400 3300
2
90 2400 3300
2
2600 3600
0.5
36 1200 1100
0.5
60 1200 1100
1
36 1400 1400
1
60 1400 1400
2
36 2400 3600
2
60 2400 3600
2
84 2000 3000
2
108 2000 3000
3
36 2400 3600
3
60 2400 3600
3
2200 3600
0.5
42 900
900
2
42 1300 1500
3
42 1800 3000
3
80 1800 3000
3
120 1500 2500
1
0.35
0.3
0.6
0.5
1.2
1.1
1
0.6
1.2
0.35
0.3
0.6
0.5
1.2
1.1
1
1
1.2
0.5
0.5
0.7
0.6
1.8
1.6
1.4
0.9
1.8
1.6
1.8
0.5
0.9
1.8
1.6
1.4
3
5
5
4.5
4.5
3
3
3
3
3.5
6.5
6.5
6
6
4.5
4.5
4.5
4.5
5
8
8
7.5
7.5
6
6
6
6
4.5
4.5
5
11
9
7.5
7.5
7.5
3400
1500
1500
2100
2100
3000
3000
2500
2500
2700
1200
1200
1700
1700
2400
2400
2000
2000
2200
1000
1000
1200
1200
2000
2000
1700
1700
2000
2000
1800
750
1100
1500
1500
1200
2700
840
840
1400
1400
2700
2700
2300
2300
2700
840
840
1400
1400
2700
2700
2300
2300
2500
770
770
1000
1000
2500
2500
2100
2100
2500
2500
2500
630
1100
2100
2100
1800
0.8
0.3
0.25
0.5
0.4
1
0.9
0.8
0.5
1
0.3
0.25
0.5
0.4
1
0.9
0.8
0.8
1
0.4
0.4
0.6
0.5
1.4
1.3
1.1
0.7
1.4
1.3
1.4
0.4
0.7
1.4
1.3
1.1
3
5
5
4.5
4.5
3
3
3
3
3.5
6.5
6.5
6
6
4.5
4.5
4.5
4.5
5
8
8
7.5
7.5
6
6
6
6
4.5
4.5
5
11
9
7.5
7.5
7.5
2700
1200
1200
1700
1700
2400
2400
2000
2000
2100
940
940
1300
1300
1900
1900
1600
1600
1700
800
800
940
940
1600
1600
1300
1300
1600
1600
1500
600
870
1200
1200
1000
2200
670
670
1100
1100
2200
2200
1800
1800
2200
670
670
1100
1100
2200
2200
1800
1800
2000
620
620
780
780
2000
2000
1700
1700
2000
2000
2000
500
840
1700
1700
1400
0.6
0.2
0.2
0.4
0.3
0.7
0.7
0.6
0.4
0.7
0.2
0.2
0.4
0.3
0.7
0.7
0.6
0.6
0.7
0.3
0.3
0.4
0.4
1.1
1
0.8
0.5
1.1
1
1.1
0.3
0.5
0.9
0.8
0.7
3
5
5
4.5
4.5
3
3
3
3
3.5
6.5
6.5
6
6
4.5
4.5
4.5
4.5
5
8
8
7.5
7.5
6
6
6
6
4.5
4.5
5
11
9
7.5
7.5
7.5
2100
900
900
1300
1300
1800
1800
1500
1500
1600
700
700
1000
1000
1500
1500
1200
1200
1300
600
600
700
700
1200
1200
1000
1000
1200
1200
1100
450
650
900
900
750
980
300
300
500
500
980
980
830
830
980
300
300
500
500
980
980
830
830
900
280
280
350
350
900
900
750
750
900
900
900
230
380
750
750
630
0.2
0.07
0.06
0.12
0.11
0.24
0.22
0.2
0.12
0.24
0.07
0.06
0.12
0.11
0.24
0.22
0.2
0.2
0.24
0.11
0.1
0.14
0.13
0.4
0.3
0.3
0.2
0.4
0.3
0.4
0.1
0.2
0.4
0.3
0.3
3
5
5
4.5
4.5
3
3
3
3
3.5
6.5
6.5
6
6
4.5
4.5
4.5
4.5
5
8
8
7.5
7.5
6
6
6
6
4.5
4.5
5
11
9
7.5
7.5
7.5
ae
Depth of cut
ap
J320
(<30HRC)
( < 45HRC)
UWC
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
43
45
Copper Alloy
CARBIDE
Aluminium Alloy
DC
DN
Taper neck type
VF
SQUARE
VFHVRB
0.01
15
DCON(h6)
LU_2
LF
BALL
DC>10
0.007
LU
Effective
length
DC < 10
APMX BHTA
RE
Effective length
for inclined angle
Inclined angle
DC < 12
0
- 0.02
h6

0
- 0.008
0
- 0.009
0
- 0.011
VFHVRBD010R02N006T09
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
BHTA APMX LU_2

0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.4
0.4
0.4
0.4
0.4
0.4
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
6
10
15
20
25
30
35
40
45
50
10
15
20
30
40
50
15
20
25
30
35
40
20
25
30
35
40
45
50
55
60
20
25
30
LU
DN
LF
DCON
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.44
1.44
1.44
1.44
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.9
2.9
2.9
60
60
60
80
80
80
90
90
90
90
60
60
80
80
90
90
60
80
80
80
80
80
80
90
90
90
90
90
100
100
100
80
80
80
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
15.6
20.6
25.6
30.6
35.6
40.6
6.6
10.6
15.6
20.6
25.6
30.6
35.6
40.6
45.6
50.6
10.6
15.6
20.6
30.6
40.6
50.6
16.2
21.3
26.5
31.7
36.9
42
20.8
25.8
30.8
35.8
40.8
45.8
50.8
55.8
60.8
20.9
25.9
30.9
7.1
11.4
16.8
22.1
27.5
32.9
38.3
43.6
49
54.4
11.4
16.8
22.2
32.9
43.7
54.4
17.4
22.9
28.5
34
39.6
45.2
22.3
27.7
33
38.4
43.8
49.2
54.5
59.9
7.6
12.3
18.1
23.9
29.7
35.5
41.3
47.2
*
*
12.3
18.1
23.9
35.6
TAPER
RE
SOLID END MILLS
DC
Stock
Order Number
No. of Flutes
Unit : mm
RADIUS
a Impact Miracle corner radius end mill for high feed and efficient machining.
*
*
18.7
24.7
30.8
36.8
*
*
24.1
29.9
35.7
*
*
*
*
*
*
22.4 24.1
27.8 30
33.1
*
* No interference
J321
VFHVRB
DC
RE
3
3
3
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
8
8
10
10
12
12
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
2
2
2
2
2
2
BHTA APMX LU_2

0.9
0.9
0.9
0.4
0.4
0.4
0.4
0.4
0.4
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
3
3
3
4
4
4
4
4
4
4
4
4
4
4
9
9
9
9
12
12
15
15
18
18
40
50
60
25
30
35
40
45
50
25
30
40
50
60
40
50
60
70
60
80
80
120
80
120
LU
DN
LF
DCON
6
6
6
7
7
7
7
7
7
7
7
7
7
7
12
12
12
12
15
15
18
18
21
21
2.9
2.9
2.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
3.9
5.85
5.85
5.85
5.85
7.85
7.85
9.7
9.7
11.7
11.7
90
90
100
80
80
80
80
90
90
90
90
100
100
100
110
110
110
110
150
150
130
180
130
180
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
16
16
16
16
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Stock
Order Number
Unit : mm
No. of Flutes
TAPER
RADIUS
BALL
SQUARE
CARBIDE
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
40.9
50.9
60.9
25.7 26.6
30.7 31.8
35.7 36.9
40.7 42.1
45.7 47.3
50.7 52.5
25.9
30.9
40.9
50.9
60.9
41.4
51.4
61.4
61.5
82
122
82.2
122.2
*
*
43.9
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
28.5
*
*
*
*
*
27.8
*
*
*
*
*
*
*
*
*
*
88
*
*
*
SOLID END MILLS
* No interference
J322
CARBIDE

Work material


Pre-hardened steel

AISI P20
AISI H13, AISI W1-10, AISI P21 AISI H13
AISI D2
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
0.8
0.8
0.8
0.8
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.4
0.4
0.4
0.4
0.4
0.4
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
6
10
15
20
25
30
35
40
45
50
10
15
20
30
40
50
15
20
25
30
35
40
20
25
30
35
40
45
50
55
60
20
25
30
40
50
60
40000
24000
16000
14000
9500
4900
4000
3500
2900
2900
27000
22000
16000
13000
4500
3700
20000
20000
16000
16000
13000
13000
20000
16000
16000
13000
13000
8000
8000
4100
4100
13000
13000
13000
11000
8000
7800
6500
2700
1200
1000
610
320
260
180
150
110
5700
3200
1400
900
230
190
7000
3600
1800
1400
1100
1000
3600
1800
1400
1100
1000
500
500
230
230
7200
7200
5700
3600
2600
2480
0.03
0.015
0.013
0.01
0.008
0.007
0.006
0.005
0.004
0.003
0.05
0.03
0.02
0.01
0.008
0.007
0.05
0.04
0.03
0.025
0.02
0.02
0.04
0.03
0.025
0.02
0.02
0.016
0.016
0.012
0.012
0.19
0.19
0.12
0.08
0.07
0.06
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1
1
1
1
1
1
33000
20000
14000
12000
8000
4100
3400
2900
2400
2400
22000
18000
14000
11000
3700
3000
17000
17000
14000
14000
11000
11000
17000
14000
14000
11000
11000
6800
6800
3500
3500
11000
11000
11000
9100
6600
6600
4600
1900
700
600
440
220
190
130
100
80
4000
2300
1200
700
160
130
5000
2600
1400
1200
800
700
2600
1400
1200
800
700
360
360
170
170
5100
5100
4000
2600
1800
1740
0.022
0.01
0.008
0.006
0.005
0.004
0.003
0.003
0.002
0.002
0.035
0.025
0.016
0.008
0.007
0.006
0.04
0.03
0.025
0.02
0.018
0.015
0.03
0.025
0.02
0.018
0.015
0.012
0.012
0.009
0.009
0.15
0.15
0.09
0.06
0.05
0.05
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1
1
1
1
1
1
27000
16000
12000
10000
6000
3000
3000
2000
2000
2000
18000
15000
13000
10000
3000
3000
13000
13000
12000
12000
10000
10000
13000
12000
12000
10000
10000
5200
5200
2700
2700
8700
8700
8700
7400
5800
5000
3700
1500
500
400
320
160
160
90
90
60
3000
1700
1000
600
120
120
3200
1800
1100
900
700
600
1800
1100
900
700
600
250
250
120
120
4000
4000
3000
2000
1500
1250
0.018
0.008
0.007
0.005
0.004
0.003
0.003
0.003
0.002
0.002
0.03
0.018
0.012
0.006
0.005
0.004
0.03
0.025
0.02
0.016
0.014
0.012
0.025
0.02
0.016
0.014
0.012
0.01
0.01
0.008
0.008
0.11
0.11
0.07
0.05
0.04
0.04
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1
1
1
1
1
1
20000
12000
10000
9000
4800
2500
2000
1700
1400
1400
14000
11000
9000
7500
2300
1900
10000
10000
9000
9000
7000
7000
10000
9000
9000
7000
7000
4000
4000
2000
2000
6500
6500
6500
5500
4600
3900
1600
700
400
300
160
80
70
50
40
30
1400
1000
700
400
70
60
1800
900
720
650
500
400
900
720
650
500
400
120
120
60
60
1800
1800
1400
1000
800
610
0.01
0.006
0.003
0.002
0.002
0.002
0.001
0.001
0.001
0.001
0.014
0.009
0.007
0.004
0.003
0.002
0.016
0.012
0.01
0.008
0.007
0.006
0.012
0.01
0.008
0.007
0.006
0.005
0.005
0.004
0.004
0.06
0.06
0.04
0.025
0.02
0.02
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.65
0.65
0.65
0.65
0.65
0.65
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
1
1
1
1
1
1
SOLID END MILLS
Dia. Corner R Taper angle Neck Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut
one side length
DC (mm) RE (mm) BHTA LU (mm) (min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm)
ae
Depth of cut
ap
J323

CARBIDE
VFHVRB
Work material


Pre-hardened steel

AISI P20
AISI H13, AISI W1-10, AISI P21 AISI H13
AISI D2
Dia. Corner R Taper angle Neck Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut
one side length
DC (mm) RE (mm) BHTA LU (mm) (min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm)
SOLID END MILLS
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
8
8
10
10
12
12
J324
1
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
2
2
2
2
2
2
0.4 25
0.4 30
0.4 35
0.4 40
0.4 45
0.4 50
0.9 25
0.9 30
0.9 40
0.9 50
0.9 60
0.9 40
0.9 50
0.9 60
0.9 70
0.9 60
0.9 80
0.9 80
0.9 120
0.9 80
0.9 120
10000 9900
10000 9900
10000 9900
10000 9900
10000 9900
8100 6300
10000 9900
10000 9900
10000 9900
8100 6300
8100 6300
6600 11000
6600 11000
6600 11000
5400 8700
5000 11000
5000 11000
4000 11000
3200 8700
3300 10000
3300 10000
0.24
0.24
0.15
0.15
0.15
0.14
0.24
0.15
0.15
0.14
0.11
0.4
0.4
0.25
0.23
0.48
0.3
0.48
0.27
0.72
0.45
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
3
3
4.5
4.5
6
6
8300
8300
8300
8300
8300
6700
8300
8300
8300
6700
6700
5500
5500
5500
4400
4200
4200
3300
2700
2700
2700
7000
7000
7000
7000
7000
4420
7000
7000
7000
4420
4420
7600
7600
7600
6200
7600
7600
7600
6200
7100
7100
0.19
0.19
0.12
0.12
0.12
0.11
0.19
0.12
0.12
0.11
0.08
0.32
0.32
0.2
0.18
0.37
0.23
0.37
0.21
0.56
0.35
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
3
3
4.5
4.5
6
6
6700
6700
6700
6700
6700
5400
6700
6700
6700
5400
5400
4500
4500
4500
3600
3300
3300
2700
2100
2200
2200
5600
5600
5600
5600
5600
3500
5600
5600
5600
3500
3500
6100
6100
6100
5000
6100
6100
6100
5000
5600
5600
0.14
0.14
0.09
0.09
0.09
0.08
0.14
0.09
0.09
0.08
0.06
0.24
0.24
0.15
0.14
0.29
0.18
0.29
0.16
0.36
0.23
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
3
3
4.5
4.5
6
6
5000
5000
5000
5000
5000
4000
5000
5000
5000
4000
4000
3300
3300
3300
2700
2500
2500
2000
1600
1700
1700
2500
2500
2500
2500
2500
1600
2500
2500
2500
1600
1600
2700
2700
2700
2200
2700
2700
2700
2200
2500
2500
0.07
0.07
0.04
0.04
0.04
0.04
0.07
0.04
0.04
0.04
0.03
0.12
0.12
0.08
0.07
0.14
0.09
0.14
0.08
0.18
0.12
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
3
3
4.5
4.5
6
6
ae
Depth of cut
ap
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
VF
Copper Alloy
42
45
CARBIDE
Aluminium Alloy
Type1
RE
DCON(h6)
DC
Hardened Steel
( < 55HRC)
UWC
APMX
LF
SQUARE
VFMHVRB
0.5<RE<6.35
DC < 12
0
- 0.020
h6
BALL
0.015
DC>12
0
- 0.030

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
DC
RE
APMX
LF
DCON
Stock
VFMHVRBD0600R050
VFMHVRBD0600R100
VFMHVRBD0800R050
VFMHVRBD0800R100
VFMHVRBD1000R050
VFMHVRBD1000R100
VFMHVRBD1000R200
VFMHVRBD1200R050
VFMHVRBD1200R100
VFMHVRBD1200R200
VFMHVRBD1600R100
VFMHVRBD1600R200
VFMHVRBD1600R300
VFMHVRBD1600R500
VFMHVRBD2000R100
VFMHVRBD2000R200
VFMHVRBD2000R300
VFMHVRBD2000R400
VFMHVRBD2000R500
VFMHVRBD2000R635
6
6
8
8
10
10
10
12
12
12
16
16
16
16
20
20
20
20
20
20
0.5
1
0.5
1
0.5
1
2
0.5
1
2
1
2
3
5
1
2
3
4
5
6.35
13
13
19
19
22
22
22
26
26
26
35
35
35
35
45
45
45
45
45
45
50
50
60
60
70
70
70
75
75
75
90
90
90
90
110
110
110
110
110
110
6
6
8
8
10
10
10
12
12
12
16
16
16
16
20
20
20
20
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TAPER
Order Number
No. of
Flutes
Unit : mm
SOLID END MILLS
materials and for long overhang applications.
RADIUS
a Vibration control end mill achieving stable machining of difficult-to-cut
J325
CARBIDE
VFMHVRB
y Side milling
material
AISI P20

Pre-hardened steel

Titanium alloy

AISI P21
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
7
8
9
10
11
12
13
14
16
18
20
21000
15000
11000
9600
8000
6800
6000
5300
4800
4400
4000
3700
3400
3000
2700
2400
1100
1250
1400
1920
2240
1900
1680
1480
1440
1350
1250
1180
1160
1140
970
860
21000
15000
11000
9600
8000
6800
6000
5300
4800
4400
4000
3700
3400
3000
2700
2400
1100
1250
1400
1920
2240
1900
1680
1480
1440
1350
1250
1180
1160
1140
970
860
14000
10600
8000
6400
5300
4500
4000
3500
3200
2900
2700
2500
2300
2000
1800
1600
560
850
960
1020
1060
1010
960
840
770
760
760
700
640
560
550
510
9600
7400
5600
4500
3700
3200
2800
2500
2200
2000
1900
1700
1600
1400
1200
1100
310
380
400
430
440
450
450
450
440
400
380
360
350
340
340
330
4800
4200
3200
2500
2100
1800
1600
1400
1300
1200
1100
1000
900
800
700
600
130
200
220
250
250
260
260
220
210
190
180
160
140
130
110
100
Depth of
cut
< 0.2DC
< 0.1DC
< 0.05DC
< 1.5DC
< 1.5DC
< 1.5DC
DC:Dia.
SOLID END MILLS
y Slotting
material
AISI P20

Pre-hardened steel

Titanium alloy

AISI P21
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
7
8
9
10
11
12
13
14
16
18
20
17000
12000
9200
7600
6400
5500
4800
4200
3800
3500
3200
2900
2700
2400
2100
1900
680
720
810
1060
1280
1210
1150
1010
910
900
900
810
760
670
670
610
10000
6900
5600
4500
3700
3200
2800
2500
2200
2000
1900
1700
1600
1400
1200
1100
400
410
490
630
740
700
670
600
530
530
530
480
450
390
380
350
9600
7400
5600
4500
3700
3200
2800
2500
2200
2000
1900
1700
1600
1400
1200
1100
310
380
400
410
440
410
390
350
350
320
300
290
290
280
270
260
4800
3200
2400
1900
1600
1400
1200
1100
1000
900
800
730
680
600
530
480
130
140
150
170
190
190
190
180
160
160
160
150
140
120
120
120
3200
2700
2000
1600
1300
1100
1000
900
800
720
660
610
570
500
440
400
80
110
120
130
160
140
130
130
130
120
110
100
90
80
70
60
DC
Depth of
cut
DC
< 1DC
DC
< 0.5DC
< 0.2DC
(MAX. 12mm)
DC:Dia.
J326
COOL STAR END MILLS
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
CARBIDE
Aluminium Alloy
Type1
DC
CoolStar
Copper Alloy
42
45
END MILLS
DCON(h6)
(<30HRC)
( < 45HRC)
VF
UWC
APMX
RE
LF
SQUARE
VFMHVRBCH
Corner radius end mill, Medium cut length, 4 flute, Irregular helix flutes, with multiple internal through coolant holes
1 < RE < 3
BALL
0.015
16 < DC < 20
0
- 0.03
DCON=16 DCON=20
h6
0
- 0.011
0
- 0.013
Order Number
DC
RE
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
VFMHVRBCHD1600R100
VFMHVRBCHD1600R300
VFMHVRBCHD2000R100
VFMHVRBCHD2000R300
16
16
20
20
1
3
1
3
35
35
45
45
90
90
110
110
16
16
20
20
4
4
4
4
a
a
a
a
Type
1
1
1
1
TAPER
difficult-to-cut materials and applications requiring long overhangs.
RADIUS
a Vibration control corner radius end mill with multiple internal through coolant holes ensures stable machining on
y Side milling
y Slotting

Work Titanium alloy
material

Work Titanium alloy
material
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
16
20
2000
1600
560
510
800
600
110
100
16
20
1400
1100
170
130
< 0.1DC
Depth of
cut
0.5DC 1.5DC
< 0.05DC
0.5DC 1.5DC
DC:Dia.
SOLID END MILLS
DC
Depth of
cut
0.5DC 1.5DC
DC:Dia.
J327

CARBIDE
VQMHVRB
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
UWC
VQ
37
40
Aluminium Alloy
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DC
SQUARE
15
RE
DCON(h6)
Type1
APMX
DC
LF
Type2
BALL
0.015
DC < 12
0
- 0.02
h6
APMX
RE
DC>12
DCON(h6)
0.2<RE<6.35
LF
0
- 0.03

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
Order Number
DC
RE
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
a Smart Miracle vibration control end mill achieving stable machining of difficult-to-cut materials and for long
VQMHVRBD0200R020
VQMHVRBD0200R030
VQMHVRBD0300R020
VQMHVRBD0300R030
VQMHVRBD0300R050
VQMHVRBD0400R020
VQMHVRBD0400R030
VQMHVRBD0400R050
VQMHVRBD0500R020
VQMHVRBD0500R030
VQMHVRBD0500R050
VQMHVRBD0500R100
VQMHVRBD0600R030
VQMHVRBD0600R050
VQMHVRBD0600R100
VQMHVRBD0800R030
VQMHVRBD0800R050
VQMHVRBD0800R100
VQMHVRBD0800R150
VQMHVRBD1000R030
VQMHVRBD1000R050
VQMHVRBD1000R100
VQMHVRBD1000R150
VQMHVRBD1000R200
VQMHVRBD1200R050
VQMHVRBD1200R100
VQMHVRBD1200R150
VQMHVRBD1200R200
VQMHVRBD1200R250
VQMHVRBD1200R300
VQMHVRBD1600R100
VQMHVRBD1600R150
2
2
3
3
3
4
4
4
5
5
5
5
6
6
6
8
8
8
8
10
10
10
10
10
12
12
12
12
12
12
16
16
0.2
0.3
0.2
0.3
0.5
0.2
0.3
0.5
0.2
0.3
0.5
1
0.3
0.5
1
0.3
0.5
1
1.5
0.3
0.5
1
1.5
2
0.5
1
1.5
2
2.5
3
1
1.5
4
4
8
8
8
11
11
11
13
13
13
13
13
13
13
19
19
19
19
22
22
22
22
22
26
26
26
26
26
26
35
35
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
60
60
60
60
70
70
70
70
70
75
75
75
75
75
75
90
90
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
10
12
12
12
12
12
12
16
16
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
J328
CARBIDE
DCON
Stock
VQMHVRBD1600R200
VQMHVRBD1600R250
VQMHVRBD1600R300
VQMHVRBD1600R400
VQMHVRBD1600R500
VQMHVRBD2000R100
VQMHVRBD2000R150
VQMHVRBD2000R200
VQMHVRBD2000R250
VQMHVRBD2000R300
VQMHVRBD2000R400
VQMHVRBD2000R500
VQMHVRBD2000R635
16
16
16
16
16
20
20
20
20
20
20
20
20
2
2.5
3
4
5
1
1.5
2
2.5
3
4
5
6.35
35
35
35
35
35
45
45
45
45
45
45
45
45
90
90
90
90
90
110
110
110
110
110
110
110
110
16
16
16
16
16
20
20
20
20
20
20
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
2
2
2
2
2
2
2
2
2
2
2
2
SQUARE
LF
BALL
APMX
RADIUS
RE
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J329

CARBIDE
VQMHVRB
y Side milling

Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

AISI 1010
SKT

Titanium alloys

AISI 630, AISI 631
15-5PH,17-4PH
2
3
4
5
6
8
10
12
16
20
25
150 24000 2400 3

150 16000 2600 4.5
150 12000 2600 6
150 9500 2600 7.5
150 8000 2600 9
150 6000 2500 12
150 4800 2300 15
150 4000 1900 18
150 3000 1600 24
150 2400 1300 30
150 1900 1100 37.5
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
120 19000 1100

120 13000 1200
120 9500 1300
120 7600 1300
120 6400 1300
120 4800 1300
120 3800 1200
120 3200 1200
120 2400 960
120 1900 760
120 1500 600
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
100 16000 830

100 11000 880
100 8000 900
100 6400 900
100 5300 1100
100 4000 1200
100 3200 1300
100 2700 1200
100 2000 960
100 1600 770
100 1300 620
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
75
75
75
75
75
75
75
75
75
75
75
12000
8000
6000
4800
4000
3000
2400
2000
1500
1200
950
720
770
790
810
810
840
770
720
600
480
380
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.4
0.6
0.8
1
1.2
1.6
2
2.4
3.2
4
5
ae
Depth
of cut
ap
SOLID END MILLS
Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

AISI 1010
SKT

Titanium alloys

AISI 630, AISI 631
15-5PH,17-4PH
2
3
4
5
6
8
10
12
16
20
25
120 19000 1300

120 13000 1400
120 9500 1400
120 7600 1400
120 6400 1400
120 4800 1300
120 3800 1200
120 3200 1000
120 2400 860
120 1900 680
120 1500 390
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
100 16000
100 11000
100 8000
100 6400
100 5300
100 4000
100 3200
100 2700
100 2000
100 1600
100 1300
630
700
700
710
710
740
680
640
530
420
340
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
80
80
80
80
80
80
80
80
80
80
80
13000
8500
6400
5100
4200
3200
2500
2100
1600
1300
1000
450
450
470
470
580
630
660
610
510
410
210
1.5
2.2
3
4.5
6
7.5
9
12
15
18
24
0.2
0.3
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
70
70
70
70
70
70
70
70
70
70
70
11000
7400
5600
4500
3700
2800
2200
1900
1400
1100
890
440
470
490
500
500
520
460
450
370
290
230
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.4
0.6
0.8
1
1.2
1.6
2
2.4
3.2
4
5
ae
Depth
of cut
ap
J330
CARBIDE
y Side milling

Work
material
Inconel718
2
3
4
5
6
8
10
12
16
20
25
180
180
180
180
180
180
180
180
180
180
180
29000
19000
14000
11000
9500
7200
5700
4800
3600
2900
2300
2900
3000
3000
3000
3000
3000
2700
2300
1900
1600
1300
3
4.5
6
7.5
9
12
15
18
24
30
37
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
40
40
40
40
40
40
40
40
40
40
40
6400
4200
3200
2500
2100
1600
1300
1100
800
640
510
230
240
240
240
250
260
290
280
200
160
130
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.2
0.3
0.4
0.5
0.6
0.8
1
1.2
1.6
2
2.5
ae
Depth
of cut
ap
Work
material
Inconel718
2
3
4
5
6
8
10
12
16
20
25
140 22000 1500

140 15000 1600
140 11000 1600
140 8900 1600
140 7400 1600
140 5600 1600
140 4500 1400
140 3700 1200
140 2800 1000
140 2200 780
140 1800 670
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
30
30
30
30
30
30
30
30
30
30
30
4800
3200
2400
1900
1600
1200
950
800
600
480
380
110
120
120
120
130
130
140
140
100
81
64
3
4.5
6
7.5
9
12
15
18
24
30
37.5
0.2
0.3
0.4
0.5
0.6
0.8
1
1.2
1.6
2
2.5
SOLID END MILLS
ae
Depth
of cut
ap
J331

CARBIDE
VQMHVRB
y Slotting

Work
material

Mild steel
Alloy tool steel
Titanium alloys
AISI 1045, AISI 4140,

ASTM A36, AISI 1010
Inconel718
AISI P21, AISI P20,

AISI 4340, SKD, SKT
AISI 304, AISI 316,

Ti-6Al-4V
AISI 630, AISI 631

15-5PH, 17-4PH
2
3
4
5
6
8
10
12
16
20
25
150
150
150
150
150
150
150
150
150
150
150
24000
16000
12000
9500
8000
6000
4800
4000
3000
2400
1900
1200
1500
1900
1900
1900
1700
1500
1300
1100
860
760
2
3
4
5
6
8
10
12
12
12
12
120
120
120
120
120
120
120
120
120
120
120
19000
13000
9500
7600
6400
4800
3800
3200
2400
1900
1500
610
730
910
910
1000
960
840
770
670
530
420
2
3
4
5
6
8
10
12
12
12
12
100
100
100
100
100
100
100
100
100
100
100
16000
11000
8000
6400
5300
4000
3200
2700
2000
1600
1300
640
660
700
720
740
800
900
860
640
510
420
2
3
4
5
6
8
10
12
12
12
12
60
60
60
60
60
60
60
60
60
60
60
9500
6400
4800
3800
3200
2400
1900
1600
1200
950
760
300 1
360 1.5
460 2
460 2.5
510 3
480 4
420 5
380 6
340 8
270 10
210 12
180
180
180
180
180
180
180
180
180
180
180
29000
19000
14000
11000
9500
7200
5700
4800
3600
2900
2300
1500
1700
2200
2200
2300
2000
1800
1500
1300
1000
920
2
3
4
5
6
8
10
12
12
12
12
30
30
30
30
30
30
30
30
30
30
30
4800
3200
2400
1900
1600
1200
950
800
600
480
380
130
150
170
170
180
190
210
200
150
120
100
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
DC
Depth
of cut
ap
DC:Dia.
SOLID END MILLS
Work
material

Mild steel
Alloy tool steel
Titanium alloys
AISI 1045, AISI 4140,

ASTM A36, AISI 1010
Inconel718
AISI P21, AISI P20,

AISI 4340, SKD, SKT
AISI 304, AISI 316,

Ti-6Al-4V
AISI 630, AISI 631

15-5PH, 17-4PH
2
3
4
5
6
8
10
12
16
20
25
100
100
100
100
100
100
100
100
100
100
100
16000
11000
8000
6400
5300
4000
3200
2700
2000
1600
1300
550
670
840
840
840
740
680
570
480
380
340
2
3
4
5
6
8
10
12
12
12
12
80 13000 270
80 8500 310
80 6400 410
80 5100 410
80 4200 440
80 3200 420
80 2500 360
80 2100 330
80 1600 300
80 1300 240
80 1000 180
2
3
4
5
6
8
10
12
12
12
12
60
60
60
60
60
60
60
60
60
60
60
9500
6400
4800
3800
3200
2400
1900
1600
1200
950
760
250
250
280
280
300
320
350
340
250
200
160
2
3
4
5
6
8
10
12
12
12
12
50
50
50
50
50
50
50
50
50
50
50
8000
5300
4000
3200
2700
2000
1600
1300
990
800
640
170 1
200 1.5
250 2
250 2.5
290 3
260 4
230 5
210 6
180 8
150 10
120 12
120
120
120
120
120
120
120
120
120
120
120
19000
13000
9500
7600
6400
4800
3800
3200
2400
1900
1500
650
790
1000
1000
1000
890
800
680
570
450
400
2
3
4
5
6
8
10
12
12
12
12
25
25
25
25
25
25
25
25
25
25
25
4000 74
2700 86
2000 93
1600 95
1300 96
990 100
800 120
660 110
500 84
400 68
320 50
0.6
0.9
1.2
1.5
1.8
2.4
3
3.6
4.8
6
7.5
DC
Depth
of cut
ap
DC:Dia.
J332
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
VQ
37
40
Copper Alloy
Aluminium Alloy
CARBIDE
Type1
DCON(h6)
DC
Hardened Steel
( < 55HRC)
UWC
APMX
RE
LF
SQUARE
VQMHVRBF
0.3 < RE < 3
0
- 0.02
DC>12
0
- 0.03

0
- 0.011
a Smart Miracle vibration control end mill achieving stable machining of difficult-to-cut materials.
a With the special substrate, suitable for finishing of heat resistance alloy, etc.
Order Number
DC
RE
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
VQMHVRBFD0600R030
VQMHVRBFD0600R050
VQMHVRBFD0600R100
VQMHVRBFD0800R050
VQMHVRBFD0800R100
VQMHVRBFD1000R030
VQMHVRBFD1000R050
VQMHVRBFD1000R100
VQMHVRBFD1000R200
VQMHVRBFD1200R100
VQMHVRBFD1200R200
VQMHVRBFD1200R300
VQMHVRBFD1600R100
VQMHVRBFD1600R200
6
6
6
8
8
10
10
10
10
12
12
12
16
16
0.3
0.5
1
0.5
1
0.3
0.5
1
2
1
2
3
1
2
13
13
13
19
19
22
22
22
22
26
26
26
35
35
50
50
50
60
60
70
70
70
70
75
75
75
90
90
6
6
6
8
8
10
10
10
10
12
12
12
16
16
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
RADIUS
0
- 0.009
TAPER
0
- 0.008
SOLID END MILLS
h6
BALL
0.015
DC < 12
J333

CARBIDE
VQMHVRBF
y Side milling
Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

AISI 1045, AISI 4140,

ASTM A36, AISI 1010
AISI P21, AISI P20,

AISI 4340, SKD, SKT
AISI 630, AISI 631,

15-5PH, 17-4PH
Inconel718
Dia. Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut
DC (mm) (mm/min) (min-1) (mm/min) ap (mm) ae (mm) (mm/min) (min-1) (mm/min) ap (mm) ae (mm) (mm/min) (min-1) (mm/min) ap (mm) ae (mm) (mm/min) (min-1) (mm/min) ap (mm) ae (mm) (mm/min) (min-1) (mm/min) ap (mm) ae (mm)
6
8
10
12
16
150
150
150
150
150
8000
6000
4800
4000
3000
2600
2500
2300
1900
1600
9
12
15
18
24
0.3
0.4
0.5
0.6
0.8
120
120
120
120
120
6400
4800
3800
3200
2400
1300
1300
1200
1200
960
9
12
15
18
24
0.3
0.4
0.5
0.6
0.8
75
75
75
75
75
4000
3000
2400
2000
1500
800
840
770
720
600
9
12
15
18
24
0.3
0.4
0.5
0.6
0.8
180
180
180
180
180
9500
7200
5700
4800
3600
3000
3000
2700
2300
1900
9
12
15
18
24
0.3
0.4
0.5
0.6
0.8
40
40
41
41
40
2100
1600
1300
1100
800
250
260
290
280
200
9
12
15
18
24
0.18
0.24
0.3
0.36
0.48
ae
Depth
of cut
ap
y Bottom face milling

Work
material

Mild steel
Pre-hardened steel,
Alloy tool steel

AISI 1045, AISI 4140,

ASTM A36, AISI 1010
AISI P21, AISI P20,

AISI 4340, SKD, SKT
AISI 630, AISI 631,

15-5PH, 17-4PH
Inconel718
SOLID END MILLS
Dia. Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut Cutting speed Revolution Feed rate Depth of cut Depth of cut
DC (mm) (mm/min) (min-1) (mm/min) ap (mm) ae (mm) (mm/min) (min-1) (mm/min) ap (mm) ae (mm) (mm/min) (min-1) (mm/min) ap (mm) ae (mm) (mm/min) (min-1) (mm/min) ap (mm) ae (mm) (mm/min) (min-1) (mm/min) ap (mm) ae (mm)
J334
6
8
10
12
16
110
110
110
110
110
5800
4400
3500
2900
2200
1400
1200
1100
930
790
0.3 4.8
0.4 6.4
0.5 8
0.6 9.6
0.8 12.8
90
90
90
90
90
4800
3600
2900
2400
1800
770
720
640
580
500
0.3 4.8
0.4 6.4
0.5 8
0.6 9.6
0.8 12.8
55
55
55
55
55
2900
2200
1800
1500
1100
460
440
400
360
310
0.3 4.8
0.4 6.4
0.5 8
0.6 9.6
0.8 12.8
130
130
130
130
130
6900
5200
4100
3400
2600
1700
1500
1300
1100
940
0.3 4.8
0.4 6.4
0.5 8
0.6 9.6
0.8 12.8
30 1600 180 0.18 4.8

30 1200 190 0.24 6.4
30 950 210 0.3 8
30 800 200 0.36 9.6
30 600 150 0.48 12.8
ae
Depth
of cut
ap
MIRACLE END MILLS
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
VC
30
Copper Alloy
CARBIDE
Aluminium Alloy
15
DN
UWC
APMX
LU
LF
DN
RE
DCON(h6)
DC
Type1
SQUARE
VC4SRB
0
- 0.020
h6
APMX
LU
LF

0
- 0.008
0
- 0.009
BALL
4 < DC < 12
DCON(h6)
DC
Type2
RE
0
- 0.011
RE
APMX
LU
DN
LF
DCON
Stock
VC4SRBD0400R0050
VC4SRBD0600R0050
VC4SRBD0600R0100
VC4SRBD0800R0050
VC4SRBD0800R0100
VC4SRBD1000R0100
VC4SRBD1000R0200
VC4SRBD1200R0100
VC4SRBD1200R0200
4
6
6
8
8
10
10
12
12
0.5
0.5
1
0.5
1
1
2
1
2
4
6
6
8
8
10
10
12
12
12
18
18
24
24
30
30
36
36
3.8
5.8
5.8
7.8
7.8
9.7
9.7
11.7
11.7
45
50
50
60
60
70
70
75
75
6
6
6
8
8
10
10
12
12
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
Type
1
2
2
2
2
2
2
2
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 4 flute corner radius end mill with relieved neck for 3D length of reach.
J335
MIRACLE END MILLS
VC4SRB
CARBIDE


material
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
2
2.5
3
4
5
6
8
10
12
16
20
30000
24000
20000
15000
12000
10000
8000
6400
5400
2400
1900
4500
3900
3500
3000
2400
2100
1500
1400
1200
550
480
0.18
0.25
0.30
0.40
0.50
0.60
0.80
1.00
1.00
2.00
3.00
24000
19000
16000
12000
9000
7000
5600
4500
3800
1200
1000
3600
3000
2700
2400
1800
1470
1050
950
860
120
100
0.10
0.13
0.15
0.20
0.25
0.30
0.40
0.50
0.50
0.80
1.00
< Please

for depth of cut.
Depth of
cut
< DC
DC
< Please

for depth of cut.
DC:Dia.
SOLID END MILLS
1)
2)
3)
4)
J336
VC4JRB
(<30HRC)
( < 45HRC)
UWC
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
VC
30
Copper Alloy
CARBIDE
Aluminium Alloy
Type1
DCON(h6)
DC
APMX
LF
RE
DC < 12
0
- 0.020
APMX
DC>12
LF
0
- 0.030

0
- 0.011
0
- 0.013

a 4 flute corner radius end mill for longer reach applications.
Order Number
DC
RE
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
VC4JRBD0300R0030
VC4JRBD0400R0030
VC4JRBD0400R0050
VC4JRBD0500R0030
VC4JRBD0500R0050
VC4JRBD0600R0030
VC4JRBD0600R0050
VC4JRBD0600R0100
VC4JRBD0800R0030
VC4JRBD0800R0050
VC4JRBD0800R0100
VC4JRBD0800R0150
VC4JRBD0800R0200
VC4JRBD1000R0030
VC4JRBD1000R0050
VC4JRBD1000R0100
VC4JRBD1000R0150
VC4JRBD1000R0200
VC4JRBD1200R0050
VC4JRBD1200R0100
VC4JRBD1200R0150
VC4JRBD1200R0200
VC4JRBD1600R0050
VC4JRBD1600R0100
VC4JRBD1600R0150
VC4JRBD1600R0200
VC4JRBD2000R0050
VC4JRBD2000R0100
VC4JRBD2000R0150
VC4JRBD2000R0200
3
4
4
5
5
6
6
6
8
8
8
8
8
10
10
10
10
10
12
12
12
12
16
16
16
16
20
20
20
20
0.3
0.3
0.5
0.3
0.5
0.3
0.5
1
0.3
0.5
1
1.5
2
0.3
0.5
1
1.5
2
0.5
1
1.5
2
0.5
1
1.5
2
0.5
1
1.5
2
12
15
15
20
20
20
20
20
25
25
25
25
25
30
30
30
30
30
30
30
30
30
50
50
50
50
55
55
55
55
50
50
50
60
60
60
60
60
70
70
70
70
70
90
90
90
90
90
90
90
90
90
110
110
110
110
110
110
110
110
6
6
6
6
6
6
6
6
8
8
8
8
8
10
10
10
10
10
12
12
12
12
16
16
16
16
20
20
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
RADIUS
0
- 0.009
TAPER
0
- 0.008
SOLID END MILLS
h6
DCON(h6)
DC
Type2
BALL
RE
SQUARE
15
J337
MIRACLE END MILLS

CARBIDE
VC4JRB
Work
material


Pre-hardened steel

Titanium alloy
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
25
4200
3400
2900
2500
1900
1600
1300
1000
800
650
110
140
170
200
220
220
170
140
110
85
3400
2700
2300
2000
1500
1300
1100
820
650
520
95
110
140
170
170
170
150
110
85
70
2600
2100
1800
1500
1200
950
800
600
480
380
70
85
100
130
150
130
100
80
70
50
2100
1700
1500
1300
1000
800
670
500
400
320
50
60
70
85
85
85
70
50
40
35
< 0.05DC
(MAX. 0.5mm)
< 0.02DC
< 2.5DC
Depth of
cut
DC
(MAX. 0.3mm)
< 2DC
DC
< 0.3DC
< 0.05DC
(MAX. 3mm)
(MAX. 0.5mm)
SOLID END MILLS
DC:Dia.
J338
3) The above table shows cutting conditions for standard side milling. For slotting, please reduce the feed rate only to 50% of the table figure.
Please set the revolution rate at 60% and the feed rate at 40% when slotting austenitic stainless steels.
MIRACLE CORNER RADIUS END MILL FOR HIGH FEED MACHINING
VCHFRB
Hardened Steel
(>55HRC)
Titanium Alloy,
DC > 6
Copper Alloy
Aluminium Alloy
LU
0.5 < RE < 3
DN
LF
DC
Effective
length
Effective length
for inclined angle
15
RE
APMX
LU
LF
0
- 0.02
h6
DC>12
Inclined angle
0
- 0.03
RE

0
- 0.008
0
- 0.009
DC
0.015
APMX
LF
Type1
Type2
Type3
SQUARE
APMX
BALL
DC
B2
DCON(h6)
RE
DC < 12
CARBIDE
DCON(h6)
10
DC < 5
Austenitic
Stainless Steel
DN
Hardened Steel
( < 55HRC)
20
DCON(h6)
(<30HRC)
( < 45HRC)
VC
UWC
0
- 0.011
LU
DN
B2
LF
DCON
VCHFRBD0200R050N06
VCHFRBD0200R050N10
VCHFRBD0300R075N09
VCHFRBD0300R075N15
VCHFRBD0400R100N12
VCHFRBD0400R100N20
VCHFRBD0500R120N15
VCHFRBD0600R150N18
VCHFRBD0600R150N30
VCHFRBD0700R150A050
VCHFRBD0700R150A080
VCHFRBD0800R200N24
VCHFRBD0800R200N40
VCHFRBD0900R200A065
VCHFRBD0900R200A100
VCHFRBD1000R200N30
VCHFRBD1000R200N50
VCHFRBD1100R200A070
VCHFRBD1100R200A110
VCHFRBD1200R300N36
VCHFRBD1200R300N60
VCHFRBD1300R300A075
VCHFRBD1300R300A120
VCHFRBD1600R300N80
2
2
3
3
4
4
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
16
0.5
0.5
0.75
0.75
1
1
1.2
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
3
3
3
3
3
2
2
3
3
4
4
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
16
6
10
9
15
12
20
15
18
30
24
40
30
50
36
60
80
1.9
1.9
2.9
2.9
3.9
3.9
4.9
5.85
5.85
7.85
7.85
9.7
9.7
11.7
11.7
15.5
8.7
6.7
6.2
4.3
3.9
2.6
1.9
50
70
50
70
50
70
70
50
90
50
80
60
90
65
100
70
100
70
110
75
110
75
120
140
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
16
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
1
1
1
1
1
1
1
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
6.2 6.5
10.4 10.8
9.4 9.7
15.6 16.1
12.4 12.8
20.7 21.4
15.5 16
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
6.9
11.5
10.4
17.3
13.7
22.9
7.5
12.4
11.1
18.6
14.7
*
* *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
* * *
*No interference
* *
TAPER
APMX
SOLID END MILLS
RE
Type
DC
Stock
Order Number
No. of Flutes
Unit : mm
RADIUS
a Suitable for high feed and efficient machining of die & mould.
J339
MIRACLE CORNER RADIUS END MILL FOR HIGH FEED MACHINING
VCHFRB
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
20
10
DC < 5
Titanium Alloy,
DC > 6
Copper Alloy
Aluminium Alloy
B2
BHTA
DC
DN
Taper neck type
Effective length
for inclined angle
Type4
RE
Effective
length
SQUARE
Hardened Steel
( < 55HRC)
VC
UWC
0.5 < RE < 3
15
APMX
DCON(h6)
CARBIDE
LU
LU_2
LF
BALL
0.015
DC < 12
0
- 0.02
h6
DC>12
Inclined angle
0
- 0.03

0
- 0.008
0
- 0.009
0
- 0.011
a Suitable for high feed and efficient machining of die & mould.
SOLID END MILLS
TAPER
RE BHTA APMX LU_2 LU
VCHFRBD0200R050N12
VCHFRBD0200R050N16
VCHFRBD0200R050N20
VCHFRBD0300R075N18
VCHFRBD0300R075N24
VCHFRBD0300R075N30
VCHFRBD0400R100N24
VCHFRBD0400R100N32
VCHFRBD0400R100N40
VCHFRBD0500R120N30
VCHFRBD0500R120N40
VCHFRBD0500R120N50
VCHFRBD0600R150N50
VCHFRBD0600R150N67
VCHFRBD0800R200N70
VCHFRBD0800R200N90
VCHFRBD1000R200N80
VCHFRBD1000R200N110
VCHFRBD1200R300N110
2
2
2
3
3
3
4
4
4
5
5
5
6
6
8
8
10
10
12
0.5
0.5
0.5
0.75
0.75
0.75
1
1
1
1.2
1.2
1.2
1.5
1.5
2
2
2
2
3
J340
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
3
3
3
4
4
4
5
5
5
6
6
8
8
10
10
12
12
16
20
18
24
30
24
32
40
30
40
50
50
67
70
90
80
110
110
4
4
4
6
6
6
8
8
8
8
8
8
16
16
18
18
20
20
24
DN
B2
1.9
1.9
1.9
2.9
2.9
2.9
3.9
3.9
3.9
4.9
4.9
4.9
5.85
5.85
7.85
7.85
9.7
9.7
11.7
6
5
4.3
3.8
3
2.6
2.2
1.7
1.4
1
2
1.7
1.2
0.9
0.9
1.3
2
1.5
1.1
LF DCON
70
70
70
80
80
80
90
90
90
90
90
110
110
130
120
150
140
160
160
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
12
16
16
16
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
DC
Stock
Order Number
No. of Flutes
RADIUS
Unit : mm
Effective length
for inclined angle
4 12.9
4 16.9
4 20.9
4 19.3
4 25.3
4 31.3
4 25.7
4 33.7
4 41.7
4
4 41.9
4 51.9
4 52.9
4
4
4 93.5
4 83.9
4 113.9
4 115.2
13.9
18.2
22.5
20.7
27.2
33.6
27.6
15
19.6
24.3
22.3
*
*
*
* *
* *
* * *
* *
* *
* *
* * *
* * *
* *
* *
* *
* *
* No interference
CARBIDE


Pre-hardened steel
Work material
Dia. Corner radius

DC (mm) RE (mm)
2
3
4
5
6
7
8
9
10
11
12
13
16
R
R
R
R
R
R
R
R
R
R
R
R
R
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
33000
22000
17000
13000
11000
9400
8200
7300
6500
6000
5500
5000
4100
10000
11000
12000
13000
13000
13000
13000
13000
13000
12000
12000
12000
10000
0.08
0.12
0.15
0.20
0.25
0.25
0.30
0.30
0.30
0.30
0.45
0.45
0.45
0.8
1.2
1.5
2.0
2.5
3.0
3.0
4.0
4.5
5.5
4.5
5.5
7.5
27000
18000
14000
11000
9000
7800
7000
6000
5500
5000
4600
4200
3400
8400
9000
9500
11000
11000
11000
11000
11000
11000
10000
10000
10000
8800
0.05
0.08
0.12
0.15
0.15
0.15
0.20
0.20
0.20
0.20
0.30
0.30
0.30
0.8
1.2
1.5
2.0
2.5
3.0
3.0
4.0
4.5
5.5
4.5
5.5
7.5
0.5
0.75
1
1.2
1.5
1.5
2
2
2
2
3
3
3
ae
Depth of cut
ap
AISI H13
AISI D2
Dia. Corner radius

DC (mm) RE (mm)
2
3
4
5
6
7
8
9
10
11
12
13
16
R
R
R
R
R
R
R
R
R
R
R
R
R
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
24000
16000
12000
9600
8000
6900
6000
5300
4800
4500
4100
3700
3000
7500
8500
8800
9500
9600
9600
9600
9500
9500
9000
9000
8900
7800
0.04
0.06
0.08
0.10
0.10
0.10
0.15
0.15
0.15
0.15
0.25
0.25
0.25
0.8
1.2
1.5
2.0
2.5
3.0
3.0
4.0
4.5
5.5
4.5
5.5
7.5
16000
11000
8000
6400
5300
4600
4000
3800
3200
2900
2700
2500
2000
3000
3300
3500
3800
3800
3800
3800
3800
3800
3500
3500
3500
3200
0.03
0.05
0.07
0.08
0.10
0.10
0.13
0.13
0.13
0.13
0.20
0.20
0.20
0.8
1.2
1.5
2.0
2.5
3.0
3.0
4.0
4.5
5.5
4.5
5.5
7.5
0.5
0.75
1
1.2
1.5
1.5
2
2
2
2
3
3
3
SOLID END MILLS
Work material
ae
Depth of cut
ap
y Coefficients respective of tool overhang

Type
Straight
Taper neck
Overhang
Revolution
Feed rate
Depth of cut
ap
L/D < 5
L/D=6
L/D=7
L/D=6
L/D=8
L/D > 10
100%
90%
80%
100%
90%
80%
100%
80%
70%
100%
80%
70%
100%
80%
70%
100%
80%
70%
1) The above table shows cutting conditions when machining with the corner
radius cutting edge.
2) This table shows the cutting conditions with less than 5D overhang length.
In the case of longer overhangs, the revolution and the feed rate should be
reduced proportionately.
5) For profile machining such as moulds, machining conditions may differ considerably
depending on the workpiece geometry, machining methods and depth of cut. Reduce
the feed rate especially when machining the corner sections of a workpiece.
6) When machining inclinations in the Z direction, set the inclination angle at
2 and reduce the feed rate by 50%.
7) If the rigidity of the machine or the work materials installation is very low,
or chattering and noise are generated, reduce the revolution and feed rate
proportionately.
J341
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
VC
45
Copper Alloy
Aluminium Alloy
DC
SQUARE
15
LF
DC
RE
APMX
DC < 12
0
- 0.02
h6
LF
DC
BALL
RE
APMX
DC>12
0
- 0.03
RE
APMX
LF
DCON(h6)
(<30HRC)
( < 45HRC)
UWC
Type1
DCON(h6)
VCMHDRB
Type2
DCON(h6)
CARBIDE
Type3
4 < DCON < 6 8<DCON<10 12<DCON<16 20<DCON<25

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
designed corner radius, for milling difficult-to-cut materials.

Order Number
DC
RE
APMX
LF
DCON
Stock
VCMHDRBD0200R020S04
VCMHDRBD0200R030S04
VCMHDRBD0300R020S06
VCMHDRBD0300R030S06
VCMHDRBD0300R050S06
VCMHDRBD0400R020S06
VCMHDRBD0400R030S06
VCMHDRBD0400R050S06
VCMHDRBD0500R020S06
VCMHDRBD0500R030S06
VCMHDRBD0500R050S06
VCMHDRBD0500R100S06
VCMHDRBD0600R030S06
VCMHDRBD0600R050S06
VCMHDRBD0600R100S06
VCMHDRBD0800R030S08
VCMHDRBD0800R050S08
VCMHDRBD0800R100S08
VCMHDRBD0800R150S08
VCMHDRBD1000R030S08
VCMHDRBD1000R050S08
VCMHDRBD1000R100S08
VCMHDRBD1000R150S08
VCMHDRBD1000R200S08
VCMHDRBD1000R030S10
VCMHDRBD1000R050S10
VCMHDRBD1000R100S10
VCMHDRBD1000R150S10
VCMHDRBD1000R200S10
VCMHDRBD1200R050S10
VCMHDRBD1200R100S10
VCMHDRBD1200R150S10
VCMHDRBD1200R200S10
VCMHDRBD1200R300S10
2
2
3
3
3
4
4
4
5
5
5
5
6
6
6
8
8
8
8
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
0.2
0.3
0.2
0.3
0.5
0.2
0.3
0.5
0.2
0.3
0.5
1
0.3
0.5
1
0.3
0.5
1
1.5
0.3
0.5
1
1.5
2
0.3
0.5
1
1.5
2
0.5
1
1.5
2
3
6
6
8
8
8
11
11
11
13
13
13
13
13
13
13
19
19
19
19
22
22
22
22
22
22
22
22
22
22
26
26
26
26
26
40
40
50
50
50
50
50
50
60
60
60
60
60
60
60
70
70
70
70
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
10
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
J342
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
a 4 flute corner radius end mill with high helix angle and newly
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
3
3
3
3
3
2
2
2
2
2
3
3
3
3
3
CARBIDE
DCON
Stock
VCMHDRBD1200R050S12
VCMHDRBD1200R100S12
VCMHDRBD1200R150S12
VCMHDRBD1200R200S12
VCMHDRBD1200R300S12
VCMHDRBD1600R100S16
VCMHDRBD1600R150S16
VCMHDRBD1600R200S16
VCMHDRBD1600R300S16
VCMHDRBD1800R100S16
VCMHDRBD1800R150S16
VCMHDRBD1800R200S16
VCMHDRBD1800R300S16
VCMHDRBD2000R100S20
VCMHDRBD2000R150S20
VCMHDRBD2000R200S20
VCMHDRBD2000R300S20
VCMHDRBD2200R100S20
VCMHDRBD2200R150S20
VCMHDRBD2200R200S20
VCMHDRBD2200R300S20
VCMHDRBD2500R100S25
VCMHDRBD2500R150S25
VCMHDRBD2500R200S25
VCMHDRBD2500R300S25
12
12
12
12
12
16
16
16
16
18
18
18
18
20
20
20
20
22
22
22
22
25
25
25
25
0.5
1
1.5
2
3
1
1.5
2
3
1
1.5
2
3
1
1.5
2
3
1
1.5
2
3
1
1.5
2
3
26
26
26
26
26
32
32
32
32
32
32
32
32
38
38
38
38
38
38
38
38
45
45
45
45
90
90
90
90
90
110
110
110
110
110
110
110
110
110
110
110
110
140
140
140
140
140
140
140
140
12
12
12
12
12
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
25
25
25
25
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
2
2
2
2
2
2
2
2
3
3
3
3
2
2
2
2
3
3
3
3
2
2
2
2
SQUARE
LF
BALL
APMX
RADIUS
RE
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J343

CARBIDE
VCMHDRB
y Side milling
Work
material


Pre-hardened steel

Titanium alloy

AISI P20

AISI P21
AISI 304, AISI 306,

Ti-6Al-4V
AISI H13
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
8
10
12
16
20
25
15000
11000
8000
6400
5900
4400
3500
2900
2200
1800
1400
550
800
900
1000
1100
1100
1000
1000
800
750
600
10000
7400
5600
4500
3700
2800
2300
1900
1400
1100
900
340
500
540
600
640
660
640
640
500
460
400
10000
7400
5600
4500
3700
2800
2300
1900
1400
1100
900
320
480
520
580
600
600
560
530
450
440
380
6400
4800
3600
2900
2400
1800
1400
1200
900
720
570
160
250
270
300
320
330
320
320
250
230
200
4800
4000
3200
2600
2100
1600
1300
1100
800
640
510
100
170
240
240
230
220
200
170
130
100
80
Depth of
cut
0.2DC
0.1DC
0.05DC
1.5DC
1.5DC
1.5DC
DC:Dia.
SOLID END MILLS
y Slotting
Work
material


Pre-hardened steel

Titanium alloy

AISI P20

AISI P21
AISI 304, AISI 306,

Ti-6Al-4V
AISI H13
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
3
4
5
6
8
10
12
16
20
25
12000
9000
7200
5800
5000
3700
3000
2500
2000
1600
1300
400
600
720
720
800
800
720
720
600
540
480
7000
5300
4000
3200
2700
2000
1600
1300
1000
800
640
200
300
360
360
400
400
360
360
280
250
220
7000
5300
4000
3200
2700
2000
1600
1300
1000
800
640
100
150
180
180
200
200
180
180
150
130
120
4200
3200
2400
1900
1600
1200
960
800
600
480
380
80
130
140
150
160
170
160
160
130
120
100
2300
1900
1400
1100
950
720
570
480
360
290
230
40
70
95
95
95
90
80
70
50
40
35
DC
Depth of
cut
DC
DC
1DC (MAX. 12mm)
0.5DC
0.2DC
DC:Dia.
J344
DF END MILLS
CARBIDE
DC < 1.5
Machineable
Ceramics
DC > 2
B2
Type1
APMX
LU
15
LF
DC
DN
RE
DCON(h6)
Graphite
30
DN
Copper Alloy
DF
DC
Aluminium Alloy
GFRP
CFRP
UWC
Type2
APMX
LU
15
LF
DC
0.01
0
- 0.02
RE
Type3
APMX
LU
LF
h6
0
- 0.008
0
- 0.009
DCON(h6)
Inclined angle
0.5<DC<12
BALL
DN
0.1 < RE < 1
RE
DCON(h6)
Effective
length
Effective length
for inclined angle
SQUARE
DFPSRB
0
- 0.011
DN
B2
LF
DCON
DFPSRBD0050R010N04
DFPSRBD0050R010N05
DFPSRBD0050R010N06
DFPSRBD0050R010N10
DFPSRBD0050R010N15
DFPSRBD0080R010N06
DFPSRBD0080R010N08
DFPSRBD0100R010N08
DFPSRBD0100R010N12
DFPSRBD0100R020N08
DFPSRBD0100R020N12
DFPSRBD0100R020N16
DFPSRBD0100R020N20
DFPSRBD0100R020N30
DFPSRBD0150R020N10
DFPSRBD0150R020N20
DFPSRBD0200R010N08
DFPSRBD0200R020N12
DFPSRBD0200R020N16
DFPSRBD0200R020N20
DFPSRBD0200R020N30
DFPSRBD0200R020N40
DFPSRBD0200R030N08
DFPSRBD0300R020N20
DFPSRBD0300R020N40
DFPSRBD0300R030N12
DFPSRBD0300R050N20
DFPSRBD0400R020N20
DFPSRBD0400R020N40
DFPSRBD0400R050N20
DFPSRBD0400R050N40
DFPSRBD0600R010N24
DFPSRBD0600R030N24
0.5
0.5
0.5
0.5
0.5
0.8
0.8
1
1
1
1
1
1
1
1.5
1.5
2
2
2
2
2
2
2
3
3
3
3
4
4
4
4
6
6
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.1
0.2
0.2
0.2
0.2
0.2
0.3
0.2
0.2
0.3
0.5
0.2
0.2
0.5
0.5
0.1
0.3
4
5
6
10
15
6
8
8
12
8
12
16
20
30
10
20
8
12
16
20
30
40
8
20
40
12
20
20
40
20
40
24
24
0.46
0.46
0.46
0.46
0.46
0.76
0.76
0.94
0.94
0.94
0.94
0.94
0.94
0.94
1.44
1.44
1.9
1.9
1.9
1.9
1.9
1.9
1.9
2.9
2.9
2.9
2.9
3.9
3.9
3.9
3.9
5.85
5.85
9.5
8.7
8.0
6.1
4.7
7.7
6.6
6.3
4.9
6.3
4.9
4.0
3.4
2.5
4.9
2.9
4.9
3.7
2.9
2.5
1.7
1.4
5.0
1.4
0.7
2.1
1.4
60
60
60
60
60
60
60
60
60
60
60
70
70
70
70
70
70
70
70
80
80
80
70
80
80
80
80
80
80
80
80
90
90
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
0.75
0.75
0.75
0.75
0.75
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2.3
2.3
3
3
3
3
3
3
3
4.5
4.5
4.5
4.5
6
6
6
6
9
9
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Effective length
for inclined angle
30'
4.1
5.2
6.2
10.3
15.5
6.2
8.3
8.5
12.6
8.5
12.6
16.8
20.9
31.3
10.5
20.9
8.4
12.5
16.7
20.8
31.2
41.5
8.4
20.8
41.5
12.5
20.8
4.3
5.4
6.4
10.7
16.0
6.4
8.6
8.8
13.1
8.8
13.1
17.4
21.7
32.4
11.0
21.7
8.7
13.0
17.3
21.5
32.2
42.9
8.7
21.5
4.6
5.7
6.9
11.5
17.2
6.9
9.2
9.5
14.1
9.5
14.1
18.7
23.3
34.8
11.8
23.3
9.4
14.0
18.6
23.2
5.0
6.2
7.5
12.4
18.6
7.5
9.9
10.2
15.2
10.2
15.2
20.2
25.1
*
*
*
*
*
*
*
*
TAPER
LU
Unit : mm
SOLID END MILLS
RE APMX
Type
DC
Stock
Order Number
No. of Flutes
Corner radius end mill with original diamond coating for precise and efficient graphite machining.
RADIUS
12.7
10.1
15.1
*
*
*
*
9.3 10.1
*
*
*
*
13.0 13.9
*
21.5
* *
* * *
* * *
* * *
* * *
* * *
* * *
* No interference
*
J345
DF END MILLS
RE APMX
LU
DN
B2
DFPSRBD0600R050N24
DFPSRBD0600R050N30
DFPSRBD0600R100N30
DFPSRBD0800R050N30
DFPSRBD0800R100N30
DFPSRBD1000R050N40
DFPSRBD1000R100N40
DFPSRBD1200R050N40
6
6
6
8
8
10
10
12
0.5
0.5
1
0.5
1
0.5
1
0.5
24
30
30
30
30
40
40
40
5.85
5.85
5.85
7.85
7.85
9.7
9.7
11.7
TAPER
SOLID END MILLS
J346
9
9
9
12
12
15
15
18
LF
90
90
90
90
90
130
130
130
DCON
6
6
6
8
8
10
10
12
4
4
4
4
4
4
4
4
Type
DC
Stock
Order Number
No. of Flutes
DFPSRB
RADIUS
BALL
SQUARE
CARBIDE
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
Unit : mm
Effective length
for inclined angle
30'
*
*
*
*
*
*
*
*
* * *
* * *
* * *
* * *
* * *
* * *
* * *
*No interference
* *
CARBIDE

Graphite
Dia.
Corner radius Neck length
DC (mm) RE (mm) LU (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Depth of cut
ae (mm)
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.1
0.2
0.2
0.2
0.2
0.2
0.3
0.2
0.2
0.5
0.3
0.2
0.2
0.5
0.5
0.1
0.3
0.5
0.5
1
0.5
1
0.5
1
0.5
30000
28000
25000
22000
20000
28000
22000
25000
22000
25000
22000
18000
15000
12000
18000
12000
24000
22000
19000
16000
13000
11000
24000
18000
12000
18000
20000
18000
13000
18000
13000
14000
14000
14000
14000
14000
10500
10500
8700
8700
7200
1100
960
850
600
500
1300
900
1500
1300
1500
1300
1000
800
600
1400
900
3300
3000
2500
2000
1600
1200
3300
3000
1800
3000
4500
4200
2800
4200
2800
4600
4600
4600
4600
4600
4000
4000
3500
3500
3000
0.05
0.05
0.05
0.04
0.03
0.08
0.08
0.1
0.1
0.1
0.1
0.08
0.08
0.07
0.15
0.12
0.2
0.2
0.2
0.2
0.16
0.14
0.3
0.3
0.25
0.3
0.3
0.4
0.4
0.4
0.4
0.6
0.6
0.6
0.6
0.6
0.8
0.8
1.0
1.0
1.2
0.23
0.23
0.23
0.21
0.18
0.45
0.45
0.6
0.6
0.45
0.45
0.4
0.4
0.35
0.8
0.65
1.2
1.2
1.2
1.2
1.0
0.8
1.2
2.0
1.7
1.5
1.5
2.7
2.7
2.3
2.3
3.8
3.8
3.8
3.8
3.0
5.3
4.5
6.8
6.0
8.0
24000
22000
20000
22000
18000
20000
18000
20000
18000
14000
14000
9600
19000
18000
15000
13000
19000
14000
9600
14000
16000
14000
10000
14000
10000
11000
11000
11000
11000
11000
8400
8400
7000
7000
5800
700
600
540
830
580
960
830
960
830
640
900
580
2100
1900
1600
1300
2100
1900
1100
1900
2900
2700
1800
2700
1800
2900
2900
2900
2900
2900
2600
2600
2200
2200
1900
0.04
0.04
0.04
0.06
0.06
0.08
0.08
0.08
0.08
0.06
0.12
0.1
0.16
0.16
0.16
0.16
0.24
0.24
0.2
0.24
0.24
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.8
0.8
1.0
0.23
0.23
0.23
0.45
0.45
0.6
0.6
0.45
0.45
0.4
0.8
0.65
1.2
1.2
1.2
1.2
1.2
2.0
1.7
1.5
1.5
2.7
2.7
2.3
2.3
3.8
3.8
3.8
3.8
3.0
5.3
4.5
6.8
6.0
8.0
0.5
0.8
1.5
8
10
12
4
5
6
10
15
6
8
8
12
8
12
16
20
30
10
20
8
12
16
20
30
40
8
20
40
20
12
20
40
20
40
24
24
24
30
30
30
30
40
40
40
SOLID END MILLS
Work material
ae
Depth of cut
ap
J347
VF6MHVRB
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
VF
Copper Alloy
43.5
45
Aluminium Alloy
Type1
SQUARE
DC
Hardened Steel
( < 55HRC)
UWC
RE
DCON(h6)
CARBIDE
APMX
LF
0.5 < RE < 2
BALL
0.015
DC < 12
0
- 0.020

0
- 0.008
0
- 0.009
0
- 0.011
0
- 0.013
Order Number
DC
RE
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
J348
0
- 0.030
a Newly developed irregular helix 6 flute geometry reduces vibrations and achieves high efficiency machining.
a Suitable for machining of difficult-to-cut materials such as stainless steel, titanium alloy and inconel.
Unit : mm
TAPER
RADIUS
h6
DC>12
VF6MHVRBD0600R050
VF6MHVRBD0600R100
VF6MHVRBD0800R050
VF6MHVRBD0800R100
VF6MHVRBD1000R050
VF6MHVRBD1000R100
VF6MHVRBD1200R050
VF6MHVRBD1200R100
VF6MHVRBD1600R100
VF6MHVRBD1600R200
VF6MHVRBD2000R100
VF6MHVRBD2000R200
6
6
8
8
10
10
12
12
16
16
20
20
0.5
1
0.5
1
0.5
1
0.5
1
1
2
1
2
13
13
19
19
22
22
26
26
32
32
38
38
50
50
60
60
70
70
75
75
90
90
100
100
6
6
8
8
10
10
12
12
16
16
20
20
6
6
6
6
6
6
6
6
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
CARBIDE

y Side milling
Work
material

Pre-hardened steel

Titanium alloy
AISI H13, AISI W1-10, AISI P21 AISI 304, AISI 306, Ti-6Al-4V
Inconel718
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
6
8
10
12
16
20
10600
8000
6400
5300
4000
3200
2900
2900
2700
2700
2200
1900
8000
6000
4800
4000
3000
2400
2000
2000
2000
2000
1600
1400
2100
1600
1300
1100
800
640
320
300
260
230
180
150
Depth of
cut
< 0.1DC
< 0.05DC
< 1.5DC
< 1.5DC
DC:Dia.
SOLID END MILLS
J349
VFSDRB
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
VF
Copper Alloy
45
Aluminium Alloy
15
DC
SQUARE
DN
Hardened Steel
( < 55HRC)
UWC
Type1
RE
DCON(h6)
CARBIDE
APMX
LU
DN
LF
RE APMX
LU
3 < DC < 12
0
- 0.02
h6
DCON(h6)
BALL
DC
Type2
LF

0
- 0.008
0
- 0.009
0
- 0.011
a 6 flute end mill with Impact Miracle coating for high hardened materials.
J350
Order Number
DC
RE
APMX
LU
DN
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VFSDRBD0300R030
VFSDRBD0400R030
VFSDRBD0500R030
VFSDRBD0600R030
VFSDRBD0600R050
VFSDRBD0600R100
VFSDRBD0800R030
VFSDRBD0800R050
VFSDRBD0800R100
VFSDRBD1000R050
VFSDRBD1000R100
VFSDRBD1200R050
VFSDRBD1200R100
3
4
5
6
6
6
8
8
8
10
10
12
12
0.3
0.3
0.3
0.3
0.5
1
0.3
0.5
1
0.5
1
0.5
1
3
4
5
6
6
6
8
8
8
10
10
12
12
9
12
15
18
18
18
24
24
24
30
30
36
36
2.9
3.9
4.9
5.85
5.85
5.85
7.85
7.85
7.85
9.7
9.7
11.7
11.7
45
45
50
50
50
50
60
60
60
70
70
75
75
6
6
6
6
6
6
8
8
8
10
10
12
12
6
6
6
6
6
6
6
6
6
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
2
2
2
2
2
2
2
2
2
2
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
15
APMX
RE
h6
DC>12
APMX
0
- 0.03
RE
APMX
LF

0
- 0.008
0
- 0.009
0
- 0.011
Type3
LF
DC
DC < 12
0
- 0.02
Type2
LF
DC
RE
Type1
SQUARE
Austenitic
Stainless Steel
BALL
Hardened Steel
(>55HRC)
CARBIDE
DCON(h6)
Hardened Steel
( < 55HRC)
45
DCON(h6)
(<30HRC)
( < 45HRC)
VF
UWC
DCON(h6)
VFMDRB
0
- 0.013
RE
APMX
LF
DCON
Stock
VFMDRBD0300R030
VFMDRBD0400R030
VFMDRBD0500R030
VFMDRBD0600R030
VFMDRBD0600R050
VFMDRBD0600R100
VFMDRBD0800R030
VFMDRBD0800R050
VFMDRBD0800R100
VFMDRBD1000R030
VFMDRBD1000R050
VFMDRBD1000R100
VFMDRBD1200R050
VFMDRBD1200R100
VFMDRBD1600R100
VFMDRBD1600R150
VFMDRBD1800R100
VFMDRBD1800R150
VFMDRBD2000R100
VFMDRBD2000R150
VFMDRBD2000R200
3
4
5
6
6
6
8
8
8
10
10
10
12
12
16
16
18
18
20
20
20
0.3
0.3
0.3
0.3
0.5
1
0.3
0.5
1
0.3
0.5
1
0.5
1
1
1.5
1
1.5
1
1.5
2
10
12
15
15
15
15
20
20
20
25
25
25
30
30
40
40
40
40
45
45
45
60
60
60
60
60
60
75
75
75
80
80
80
100
100
110
110
120
120
125
125
125
6
6
6
6
6
6
8
8
8
10
10
10
12
12
16
16
16
16
20
20
20
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
2
2
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 6 flute corner radius end mill with Impact Miracle coating for high hardened materials.
J351

CARBIDE
VFSDRB
VFMDRB
Work
material
AISI H13
AISI D2
AISI W1, AISI M2
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
1
2
3
4
6
8
10
12
16
20
25
40000
40000
32000
24000
16000
12000
9600
8000
6000
4800
3800
1200
2000
3800
4400
5800
5800
5800
4800
3600
2900
2300
0.05
0.1
0.2
0.2
0.3
0.4
0.5
0.6
0.8
1.0
1.0
40000
24000
16000
12000
8000
6000
4800
4000
3000
2400
1900
800
1000
1900
2200
2900
2900
2900
2400
1800
1400
1100
0.03
0.05
0.1
0.1
0.2
0.2
0.3
0.3
0.5
0.5
0.5
32000
16000
11000
8000
5300
4000
3200
2700
2000
1600
1300
500
600
1200
1300
1800
1800
1800
1500
1100
880
720
0.02
0.05
0.05
0.05
0.1
0.1
0.2
0.2
0.3
0.3
0.3
Depth of
cut

for depth of cut.

for depth of cut.
< 1.5DC
< 1.0DC
DC:Dia.
SOLID END MILLS
Work
material
AISI H13
AISI D2
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
1
2
15000
8000
300
320
0.1
0.2
9500
4800
110
190
0.05
0.1
DC
Depth of
cut

for depth of cut.
DC:Dia.
J352
COOL STAR END MILLS
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
43.5
45
Copper Alloy
CARBIDE
Aluminium Alloy
Type1
DC
CoolStar
VF
UWC
RE
APMX
DCON(h6)
END MILLS
LF
SQUARE
VF6MHVRBCH
0.5 < RE < 3
0
- 0.020
BALL
0.015
DC < 12
DC>12
0
- 0.030
DCON=10 DCON=12 DCON=16 DCON=20
h6
0
- 0.009
0
- 0.011
0
- 0.011
0
- 0.013
DC
RE
APMX
LF
DCON
Stock
VF6MHVRBCHD1000R050
VF6MHVRBCHD1000R100
VF6MHVRBCHD1200R050
VF6MHVRBCHD1200R100
VF6MHVRBCHD1600R100
VF6MHVRBCHD1600R300
VF6MHVRBCHD2000R100
VF6MHVRBCHD2000R300
10
10
12
12
16
16
20
20
0.5
1
0.5
1
1
3
1
3
22
22
26
26
32
32
38
38
70
70
75
75
90
90
100
100
10
10
12
12
16
16
20
20
6
6
6
6
6
6
6
6
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1

y Side milling

Work Titanium alloy
material

Work
material
Inconel718

Titanium alloy
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
10
12
16
20
4800
4000
3000
2400
2000
2000
1600
1400
1300
1100
800
640
260
230
180
150
10
12
16
20
4800
4000
3000
2400
1400
1200
1100
900
Depth of
cut
< 0.1DC
< 0.05DC
0.5DC 1.5DC
0.5DC 1.5DC
TAPER
Order Number
No. of
Flutes
Unit : mm
SOLID END MILLS
stable machining on difficult-to-cut materials and applications requiring long overhangs.
RADIUS
a Vibration control corner radius end mill with multiple internal through coolant holes ensures
1.5DC<
< 0.1DC
Depth of
cut
DC:Dia.
0.5DC 1.5DC
DC:Dia.
J353
COOL STAR END MILLS
VF8MHVRBCH
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
SQUARE
CoolStar
VF
44
45
Copper Alloy
Aluminium Alloy
END MILLS
Type1
DCON(h6)
(<30HRC)
( < 45HRC)
UWC
DC
CARBIDE
APMX
RE
LF
1 < RE < 3
BALL
0.015
16<DC<20
0
- 0.03
DCON=16 DCON=20
h6
0
- 0.011
0
- 0.013

Order Number
DC
RE
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
TAPER
RADIUS
a Vibration control corner radius end mill with multiple internal through coolant holes ensures stable
VF8MHVRBCHD1600R100
VF8MHVRBCHD1600R300
VF8MHVRBCHD2000R100
VF8MHVRBCHD2000R300
16
16
20
20
1
3
1
3
32
32
38
38
90
90
100
100
16
16
20
20
8
8
8
8
a
a
a
a
Type
1
1
1
1
SOLID END MILLS

y Side milling

Work Titanium alloy
material

Work
material
Inconel718

Titanium alloy
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
16
20
3000
2400
2100
1900
800
640
240
200
16
20
3000
2400
1400
1200
Depth of
cut
< 0.08DC
< 0.05DC
0.5DC 1.5DC
0.5DC 1.5DC
1.5DC<
< 0.08DC
Depth of
cut
DC:Dia.
0.5DC 1.5DC
DC:Dia.
J354
MSTAR END MILLS

DC<0.4
Aluminium Alloy
DC
B7
Copper Alloy
APMX
DC_2
LF
(B7)
DC
B7
DC > 0.5
0
- 0.020
0
- 0.030
APMX
B7
h6
DC
5'
4 < DCON < 6 8<DCON<10 12<DCON<16

0
- 0.008
LF
DC_2
DC<0.5
0
- 0.009
APMX
0
- 0.011
DC > 0.4
LF
Type1
Type2
Type3
SQUARE
Titanium Alloy,
BALL
Austenitic
Stainless Steel
DCON(h6)
Hardened Steel
(>55HRC)
CARBIDE
DCON(h6)
Hardened Steel
( < 55HRC)
30
DC_2
(<30HRC)
( < 45HRC)
MS
UWC
DCON(h6)
MS2MT
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
3
4
5
APMX
DC_2
LF
DCON
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
2
2
2
2
2
2
2
0.21
0.23
0.24
0.26
0.28
0.31
0.34
0.4
0.48
0.32
0.34
0.36
0.38
0.43
0.47
0.51
0.59
0.72
0.43
0.46
0.48
0.51
0.57
0.62
0.68
0.79
0.96
0.53
0.57
0.6
0.64
0.71
0.78
0.85
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
TAPER
MS2MTD0020T0030
MS2MTD0020T0100
MS2MTD0020T0130
MS2MTD0020T0200
MS2MTD0020T0300
MS2MTD0020T0400
MS2MTD0020T0500
MS2MTD0020T0700
MS2MTD0020T1000
MS2MTD0030T0030
MS2MTD0030T0100
MS2MTD0030T0130
MS2MTD0030T0200
MS2MTD0030T0300
MS2MTD0030T0400
MS2MTD0030T0500
MS2MTD0030T0700
MS2MTD0030T1000
MS2MTD0040T0030
MS2MTD0040T0100
MS2MTD0040T0130
MS2MTD0040T0200
MS2MTD0040T0300
MS2MTD0040T0400
MS2MTD0040T0500
MS2MTD0040T0700
MS2MTD0040T1000
MS2MTD0050T0030
MS2MTD0050T0100
MS2MTD0050T0130
MS2MTD0050T0200
MS2MTD0050T0300
MS2MTD0050T0400
MS2MTD0050T0500
B7
SOLID END MILLS
DC
Stock
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute taper end mill for general use.
J355
MSTAR END MILLS
MS2MT
J356
DC
MS2MTD0050T0700
MS2MTD0050T1000
MS2MTD0060T0030
MS2MTD0060T0100
MS2MTD0060T0130
MS2MTD0060T0200
MS2MTD0060T0230
MS2MTD0060T0300
MS2MTD0060T0400
MS2MTD0060T0500
MS2MTD0060T0700
MS2MTD0060T1000
MS2MTD0070T0030
MS2MTD0070T0100
MS2MTD0070T0130
MS2MTD0070T0200
MS2MTD0070T0300
MS2MTD0070T0400
MS2MTD0070T0500
MS2MTD0070T0700
MS2MTD0070T1000
MS2MTD0080T0030
MS2MTD0080T0100
MS2MTD0080T0130
MS2MTD0080T0200
MS2MTD0080T0230
MS2MTD0080T0300
MS2MTD0080T0400
MS2MTD0080T0500
MS2MTD0080T0700
MS2MTD0080T1000
MS2MTD0090T0030
MS2MTD0090T0100
MS2MTD0090T0130
MS2MTD0090T0200
MS2MTD0090T0300
MS2MTD0090T0400
MS2MTD0090T0500
MS2MTD0090T0700
MS2MTD0090T1000
MS2MTD0100T0030
MS2MTD0100T0100
MS2MTD0100T0130
MS2MTD0100T0200
MS2MTD0100T0230
MS2MTD0100T0300
MS2MTD0100T0400
MS2MTD0100T0500
MS2MTD0100T0700
MS2MTD0100T1000
MS2MTD0150T0030
MS2MTD0150T0100
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
1
1
1
1
1
1
1
1
1
1
1.5
1.5
B7
7
10
30'
1
1 30'
2
2 30'
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
2 30'
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
2 30'
3
4
5
7
10
30'
1
APMX
DC_2
LF
DCON
Stock
Order Number
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
5
5
0.99
1.21
0.63
0.67
0.7
0.74
0.77
0.81
0.88
0.95
1.09
1.31
0.73
0.77
0.8
0.84
0.91
0.98
1.05
1.19
1.41
0.85
0.9
0.96
1.01
1.06
1.11
1.22
1.32
1.54
1.86
0.95
1
1.06
1.11
1.21
1.32
1.42
1.64
1.96
1.07
1.14
1.21
1.28
1.35
1.42
1.56
1.7
1.98
2.41
1.59
1.67
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
CARBIDE
LF
DCON
Stock
MS2MTD0150T0130
MS2MTD0150T0200
MS2MTD0150T0230
MS2MTD0150T0300
MS2MTD0150T0400
MS2MTD0150T0500
MS2MTD0150T0700
MS2MTD0150T1000
MS2MTD0200T0030
MS2MTD0200T0100
MS2MTD0200T0130
MS2MTD0200T0200
MS2MTD0200T0230
MS2MTD0200T0300
MS2MTD0200T0400
MS2MTD0200T0500
MS2MTD0200T0700
MS2MTD0200T1000
MS2MTD0250T0030
MS2MTD0250T0100
MS2MTD0250T0130
MS2MTD0250T0200
MS2MTD0250T0230
MS2MTD0250T0300
MS2MTD0250T0400
MS2MTD0250T0500
MS2MTD0250T0700
MS2MTD0250T1000
MS2MTD0300T0030
MS2MTD0300T0100
MS2MTD0300T0130
MS2MTD0300T0200
MS2MTD0300T0300
MS2MTD0300T0400
MS2MTD0300T0500
MS2MTD0300T0700
MS2MTD0300T1000
MS2MTD0400T0030
MS2MTD0400T0100
MS2MTD0400T0130
MS2MTD0400T0200
MS2MTD0400T0300
MS2MTD0400T0400
MS2MTD0400T0500
MS2MTD0400T0700
MS2MTD0400T1000
MS2MTD0500T0030
MS2MTD0500T0100
MS2MTD0500T0130
MS2MTD0500T0200
MS2MTD0500T0300
MS2MTD0500T0400
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
1 30'
2
2 30'
3
4
5
7
10
30'
1
1 30'
2
2 30'
3
4
5
7
10
30'
1
1 30'
2
2 30'
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
3
4
5
7
10
30'
1
1 30'
2
3
4
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
15
15
15
15
15
15
15
15
15
20
20
20
20
20
20
1.76
1.85
1.94
2.02
2.2
2.37
2.73
3.26
2.1
2.21
2.31
2.42
2.52
2.63
2.84
3.05
3.47
4.12
2.64
2.78
2.92
3.06
3.2
3.34
3.62
3.9
4.46
5.32
3.17
3.35
3.52
3.7
4.05
4.4
4.75
5.46
6.53
4.26
4.52
4.79
5.05
5.57
6.1
6.62
7.68
9.29
5.35
5.7
6.05
6.4
7.1
7.8
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
50
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
55
55
55
60
55
55
55
55
55
60
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
6
6
6
6
6
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
2
2
3
2
1
1
1
1
1
1
1
2
3
1
1
1
1
1
3
3
3
3
1
1
3
3
3
3
SQUARE
DC_2
BALL
APMX
RADIUS
B7
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J357
MSTAR END MILLS
MS2MT
MS2MTD0500T0500
MS2MTD0500T0700
MS2MTD0500T1000
MS2MTD0600T0030
MS2MTD0600T0100
MS2MTD0600T0130
MS2MTD0600T0200
MS2MTD0600T0300
MS2MTD0600T0500
MS2MTD0800T0030
MS2MTD0800T0100
MS2MTD0800T0130
MS2MTD0800T0200
MS2MTD0800T0300
MS2MTD0800T0500
MS2MTD1000T0030
MS2MTD1000T0100
MS2MTD1000T0130
MS2MTD1000T0200
MS2MTD1000T0300
MS2MTD1000T0500
5
5
5
6
6
6
6
6
6
8
8
8
8
8
8
10
10
10
10
10
10
J358
B7
5
7
10
30'
1
1 30'
2
3
5
30'
1
1 30'
2
3
5
30'
1
1 30'
2
3
5
APMX
DC_2
LF
DCON
Stock
DC
Unit : mm
No. of
Flutes
Order Number
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
35
35
35
35
35
35
8.5
9.91
12.05
6.35
6.7
7.05
7.4
8.1
9.5
8.44
8.87
9.31
9.75
10.62
12.37
10.61
11.22
11.83
12.44
13.67
16.12
60
70
80
60
60
60
60
65
70
70
70
70
70
75
95
90
90
90
95
95
95
8
10
12
6
6
6
6
8
8
8
8
8
8
10
12
10
10
10
12
12
16
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
3
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
CARBIDE

y Slotting
material

Pre-hardened steel
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
(mm)
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.5
40000
40000
40000
37000
32000
27000
24000
21000
19000
13000
320
400
450
500
530
560
610
610
610
720
0.005
0.006
0.008
0.010
0.013
0.015
0.018
0.020
0.025
0.040
40000
40000
40000
32000
26000
23000
20000
18000
16000
11000
180
220
270
320
340
380
410
450
450
540
0.004
0.005
0.006
0.008
0.010
0.011
0.013
0.015
0.020
0.030
40000
35000
31000
25000
21000
18000
16000
14000
13000
8500
100
130
150
160
170
180
210
210
210
270
0.002
0.003
0.004
0.005
0.006
0.007
0.008
0.009
0.010
0.015
Depth of
cut
Please refer to the list above for depth of cut.
DC:Dia.

material

Pre-hardened steel
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
2.5
3
4
5
6
8
10
9500
7800
6400
4800
3800
3200
2400
1900
720
800
800
800
800
800
700
600
8000
6300
5300
4000
3200
2600
2000
1600
540
540
540
540
540
540
480
410
6400
5000
4200
3200
2500
2100
1600
1300
300
300
300
300
300
300
270
240
<0.03DC
<0.05DC
Depth of
cut
SOLID END MILLS
y Side milling
<2.5DC
<2.5DC
DC:Dia.
J359
MSTAR END MILLS
MS4LT
e
DC<3
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
B7
15
Type1
APMX
BALL
LF
DC<0.5
DC > 0.5
0
- 0.020
0
- 0.040
DC > 3
SQUARE
Hardened Steel
( < 55HRC)
25
DCON(h6)
(<30HRC)
( < 45HRC)
MS
UWC
DC_2
CARBIDE
5'
h6
DCON=3 4 < DCON < 6

0
- 0.006
0
- 0.008
a 4 flute taper end mill for rib milling.
J360
DC
MS4LTD0020T0030L02
MS4LTD0020T0100L02
MS4LTD0020T0130L02
MS4LTD0020T0200L02
MS4LTD0030T0030L03
MS4LTD0030T0100L03
MS4LTD0030T0130L03
MS4LTD0030T0200L03
MS4LTD0040T0030L04
MS4LTD0040T0100L04
MS4LTD0040T0130L04
MS4LTD0040T0200L04
MS4LTD0050T0030L04
MS4LTD0050T0030L06
MS4LTD0050T0100L04
MS4LTD0050T0100L06
MS4LTD0050T0130L04
MS4LTD0050T0130L06
MS4LTD0050T0200L04
MS4LTD0050T0200L06
MS4LTD0060T0030L04
MS4LTD0060T0030L06
MS4LTD0060T0100L04
MS4LTD0060T0100L06
MS4LTD0060T0130L04
MS4LTD0060T0130L06
MS4LTD0060T0200L04
MS4LTD0060T0200L06
MS4LTD0070T0030L06
MS4LTD0070T0030L08
MS4LTD0070T0100L06
MS4LTD0070T0100L08
MS4LTD0070T0130L06
MS4LTD0070T0130L08
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
0.7
0.7
B7
30'
1
1 30'
2
30'
1
1 30'
2
30'
1
1 30'
2
30'
30'
1
1
1 30'
1 30'
2
2
30'
30'
1
1
1 30'
1 30'
2
2
30'
30'
1
1
1 30'
1 30'
APMX
DC_2
LF
DCON
Stock
Order Number
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
Unit : mm
2
2
2
2
3
3
3
3
4
4
4
4
4
6
4
6
4
6
4
6
4
6
4
6
4
6
4
6
6
8
6
8
6
8
0.23
0.27
0.3
0.34
0.35
0.4
0.46
0.51
0.47
0.54
0.61
0.68
0.57
0.6
0.64
0.71
0.71
0.81
0.78
0.92
0.67
0.7
0.74
0.81
0.81
0.91
0.88
1.02
0.8
0.84
0.91
0.98
1.01
1.12
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
40
45
40
45
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CARBIDE
1
1
1
1
1
1 30'
1 30'
1 30'
1 30'
1 30'
2
2
2
2
2
15'
15'
15'
15'
30'
30'
30'
30'
1
1
1
1
1
1 30'
1 30'
1 30'
1 30'
1 30'
2
2
2
2
2
15'
15'
15'
DCON
6
8
4
6
8
10
4
6
8
10
12
4
6
8
10
12
4
6
8
10
12
4
6
8
10
12
6
8
10
12
6
8
10
12
6
8
10
12
16
6
8
10
12
16
6
8
10
12
16
6
10
12
1.12
1.26
0.83
0.85
0.87
0.89
0.87
0.9
0.94
0.97
1.01
0.94
1.01
1.08
1.15
1.22
1.01
1.11
1.22
1.32
1.43
1.08
1.22
1.36
1.5
1.64
1.05
1.07
1.09
1.1
1.1
1.14
1.17
1.21
1.21
1.28
1.35
1.42
1.56
1.31
1.42
1.52
1.63
1.84
1.42
1.56
1.7
1.84
2.12
1.25
1.29
1.3
40
45
45
45
45
45
45
45
45
45
50
45
45
45
45
50
45
45
45
45
50
45
45
45
45
50
45
45
45
50
45
45
45
50
45
45
45
50
55
45
45
45
50
55
45
45
45
50
55
45
45
50
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SQUARE
15'
15'
15'
15'
30'
30'
30'
30'
30'
LF
BALL
2
2
DC_2
RADIUS
0.7
0.7
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.2
1.2
1.2
APMX
TAPER
MS4LTD0070T0200L06
MS4LTD0070T0200L08
MS4LTD0080T0015L04
MS4LTD0080T0015L06
MS4LTD0080T0015L08
MS4LTD0080T0015L10
MS4LTD0080T0030L04
MS4LTD0080T0030L06
MS4LTD0080T0030L08
MS4LTD0080T0030L10
MS4LTD0080T0030L12
MS4LTD0080T0100L04
MS4LTD0080T0100L06
MS4LTD0080T0100L08
MS4LTD0080T0100L10
MS4LTD0080T0100L12
MS4LTD0080T0130L04
MS4LTD0080T0130L06
MS4LTD0080T0130L08
MS4LTD0080T0130L10
MS4LTD0080T0130L12
MS4LTD0080T0200L04
MS4LTD0080T0200L06
MS4LTD0080T0200L08
MS4LTD0080T0200L10
MS4LTD0080T0200L12
MS4LTD0100T0015L06
MS4LTD0100T0015L08
MS4LTD0100T0015L10
MS4LTD0100T0015L12
MS4LTD0100T0030L06
MS4LTD0100T0030L08
MS4LTD0100T0030L10
MS4LTD0100T0030L12
MS4LTD0100T0100L06
MS4LTD0100T0100L08
MS4LTD0100T0100L10
MS4LTD0100T0100L12
MS4LTD0100T0100L16
MS4LTD0100T0130L06
MS4LTD0100T0130L08
MS4LTD0100T0130L10
MS4LTD0100T0130L12
MS4LTD0100T0130L16
MS4LTD0100T0200L06
MS4LTD0100T0200L08
MS4LTD0100T0200L10
MS4LTD0100T0200L12
MS4LTD0100T0200L16
MS4LTD0120T0015L06
MS4LTD0120T0015L10
MS4LTD0120T0015L12
B7
SOLID END MILLS
DC
Stock
Order Number
No. of
Flutes
Unit : mm
J361
MSTAR END MILLS
MS4LT
J362
DC
MS4LTD0120T0015L16
MS4LTD0120T0030L06
MS4LTD0120T0030L10
MS4LTD0120T0030L12
MS4LTD0120T0030L16
MS4LTD0120T0100L06
MS4LTD0120T0100L10
MS4LTD0120T0100L12
MS4LTD0120T0100L16
MS4LTD0120T0100L20
MS4LTD0120T0130L06
MS4LTD0120T0130L10
MS4LTD0120T0130L12
MS4LTD0120T0130L16
MS4LTD0120T0130L20
MS4LTD0120T0200L06
MS4LTD0120T0200L10
MS4LTD0120T0200L12
MS4LTD0120T0200L16
MS4LTD0120T0200L20
MS4LTD0130T0030L12
MS4LTD0130T0100L12
MS4LTD0130T0130L12
MS4LTD0130T0200L12
MS4LTD0140T0030L12
MS4LTD0140T0100L12
MS4LTD0140T0130L12
MS4LTD0140T0200L12
MS4LTD0150T0015L06
MS4LTD0150T0015L08
MS4LTD0150T0015L10
MS4LTD0150T0015L12
MS4LTD0150T0015L16
MS4LTD0150T0015L20
MS4LTD0150T0030L06
MS4LTD0150T0030L08
MS4LTD0150T0030L10
MS4LTD0150T0030L12
MS4LTD0150T0030L16
MS4LTD0150T0030L20
MS4LTD0150T0100L06
MS4LTD0150T0100L08
MS4LTD0150T0100L10
MS4LTD0150T0100L12
MS4LTD0150T0100L16
MS4LTD0150T0100L20
MS4LTD0150T0100L25
MS4LTD0150T0130L06
MS4LTD0150T0130L08
MS4LTD0150T0130L10
MS4LTD0150T0130L12
MS4LTD0150T0130L16
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.3
1.3
1.3
1.3
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
B7
15'
30'
30'
30'
30'
1
1
1
1
1
1 30'
1 30'
1 30'
1 30'
1 30'
2
2
2
2
2
30'
1
1 30'
2
30'
1
1 30'
2
15'
15'
15'
15'
15'
15'
30'
30'
30'
30'
30'
30'
1
1
1
1
1
1
1
1 30'
1 30'
1 30'
1 30'
1 30'
APMX
DC_2
LF
DCON
Stock
Order Number
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
16
6
10
12
16
6
10
12
16
20
6
10
12
16
20
6
10
12
16
20
12
12
12
12
12
12
12
12
6
8
10
12
16
20
6
8
10
12
16
20
6
8
10
12
16
20
25
6
8
10
12
16
1.34
1.3
1.37
1.41
1.48
1.41
1.55
1.62
1.76
1.9
1.51
1.72
1.83
2.04
2.25
1.62
1.9
2.04
2.32
2.6
1.51
1.72
1.93
2.14
1.61
1.82
2.03
2.24
1.55
1.57
1.59
1.6
1.64
1.67
1.6
1.64
1.67
1.71
1.78
1.85
1.71
1.78
1.85
1.92
2.06
2.2
2.37
1.81
1.92
2.02
2.13
2.34
55
45
45
50
55
45
45
50
55
55
45
45
50
55
55
45
45
50
55
55
50
50
50
50
50
50
50
50
45
45
45
50
55
55
45
45
45
50
55
55
45
45
45
50
55
55
60
45
45
45
50
55
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CARBIDE
LF
DCON
Stock
MS4LTD0150T0130L20
MS4LTD0150T0130L25
MS4LTD0150T0200L06
MS4LTD0150T0200L08
MS4LTD0150T0200L10
MS4LTD0150T0200L12
MS4LTD0150T0200L16
MS4LTD0150T0200L20
MS4LTD0150T0200L25
MS4LTD0160T0030L08
MS4LTD0160T0030L12
MS4LTD0160T0030L16
MS4LTD0160T0030L20
MS4LTD0160T0100L08
MS4LTD0160T0100L12
MS4LTD0160T0100L16
MS4LTD0160T0100L20
MS4LTD0160T0130L08
MS4LTD0160T0130L12
MS4LTD0160T0130L16
MS4LTD0160T0130L20
MS4LTD0160T0200L08
MS4LTD0160T0200L12
MS4LTD0160T0200L16
MS4LTD0160T0200L20
MS4LTD0180T0015L08
MS4LTD0180T0015L16
MS4LTD0180T0015L24
MS4LTD0180T0030L08
MS4LTD0180T0030L16
MS4LTD0180T0030L24
MS4LTD0180T0100L08
MS4LTD0180T0100L16
MS4LTD0180T0100L24
MS4LTD0180T0130L08
MS4LTD0180T0130L16
MS4LTD0180T0130L24
MS4LTD0180T0200L08
MS4LTD0180T0200L16
MS4LTD0180T0200L24
MS4LTD0200T0015L08
MS4LTD0200T0015L10
MS4LTD0200T0015L12
MS4LTD0200T0015L16
MS4LTD0200T0015L20
MS4LTD0200T0015L25
MS4LTD0200T0030L08
MS4LTD0200T0030L10
MS4LTD0200T0030L12
MS4LTD0200T0030L16
MS4LTD0200T0030L20
MS4LTD0200T0030L25
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
2
2
2
2
2
2
2
2
2
2
2
2
1 30'
1 30'
2
2
2
2
2
2
2
30'
30'
30'
30'
1
1
1
1
1 30'
1 30'
1 30'
1 30'
2
2
2
2
15'
15'
15'
30'
30'
30'
1
1
1
1 30'
1 30'
1 30'
2
2
2
15'
15'
15'
15'
15'
15'
30'
30'
30'
30'
30'
30'
20
25
6
8
10
12
16
20
25
8
12
16
20
8
12
16
20
8
12
16
20
8
12
16
20
8
16
24
8
16
24
8
16
24
8
16
24
8
16
24
8
10
12
16
20
25
8
10
12
16
20
25
2.55
2.81
1.92
2.06
2.2
2.34
2.62
2.9
3.25
1.74
1.81
1.88
1.95
1.88
2.02
2.16
2.3
2.02
2.23
2.44
2.65
2.16
2.44
2.72
3
1.87
1.94
2.01
1.94
2.08
2.22
2.08
2.36
2.64
2.22
2.64
3.06
2.36
2.92
3.48
2.07
2.09
2.1
2.14
2.17
2.22
2.14
2.17
2.21
2.28
2.35
2.44
55
60
45
45
45
50
55
55
60
45
50
55
55
45
50
55
55
45
50
55
55
45
50
55
55
45
55
60
45
55
60
45
55
60
45
55
60
45
55
60
45
45
50
55
55
60
45
45
50
55
55
60
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SQUARE
DC_2
BALL
APMX
RADIUS
B7
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J363
MSTAR END MILLS
MS4LT
J364
Order Number
DC
B7
APMX
DC_2
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
MS4LTD0200T0030L30
MS4LTD0200T0100L08
MS4LTD0200T0100L10
MS4LTD0200T0100L12
MS4LTD0200T0100L16
MS4LTD0200T0100L20
MS4LTD0200T0100L25
MS4LTD0200T0100L30
MS4LTD0200T0130L08
MS4LTD0200T0130L10
MS4LTD0200T0130L12
MS4LTD0200T0130L16
MS4LTD0200T0130L20
MS4LTD0200T0130L25
MS4LTD0200T0130L30
MS4LTD0200T0200L08
MS4LTD0200T0200L10
MS4LTD0200T0200L12
MS4LTD0200T0200L16
MS4LTD0200T0200L20
MS4LTD0200T0200L25
MS4LTD0200T0200L30
MS4LTD0200T0300L12
MS4LTD0200T0300L16
MS4LTD0200T0300L20
MS4LTD0200T0300L25
MS4LTD0200T0300L30
MS4LTD0250T0030L10
MS4LTD0250T0030L16
MS4LTD0250T0030L20
MS4LTD0250T0030L25
MS4LTD0250T0030L30
MS4LTD0250T0100L10
MS4LTD0250T0100L16
MS4LTD0250T0100L20
MS4LTD0250T0100L25
MS4LTD0250T0100L30
MS4LTD0250T0130L10
MS4LTD0250T0130L16
MS4LTD0250T0130L20
MS4LTD0250T0130L25
MS4LTD0250T0130L30
MS4LTD0250T0200L10
MS4LTD0250T0200L16
MS4LTD0250T0200L20
MS4LTD0250T0200L25
MS4LTD0250T0200L30
MS4LTD0300T0030L25
MS4LTD0300T0030L40
MS4LTD0300T0100L25
MS4LTD0300T0100L40
MS4LTD0300T0130L25
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
3
3
3
3
30'
1
1
1
1
1
1
1
1 30'
1 30'
1 30'
1 30'
1 30'
1 30'
1 30'
2
2
2
2
2
2
2
3
3
3
3
3
30'
30'
30'
30'
30'
1
1
1
1
1
1 30'
1 30'
1 30'
1 30'
1 30'
2
2
2
2
2
30'
30'
1
1
1 30'
30
8
10
12
16
20
25
30
8
10
12
16
20
25
30
8
10
12
16
20
25
30
12
16
20
25
30
10
16
20
25
30
10
16
20
25
30
10
16
20
25
30
10
16
20
25
30
25
40
25
40
25
2.52
2.28
2.35
2.42
2.56
2.7
2.87
3.05
2.42
2.52
2.63
2.84
3.05
3.31
3.57
2.56
2.7
2.84
3.12
3.4
3.75
4.1
3.26
3.68
4.1
4.62
5.14
2.67
2.78
2.85
2.94
3.02
2.85
3.06
3.2
3.37
3.55
3.02
3.34
3.55
3.81
4.07
3.2
3.62
3.9
4.25
4.6
3.44
3.7
3.87
4.4
4.31
65
45
45
50
55
55
60
65
45
45
50
55
55
60
65
45
45
50
55
55
60
65
50
55
55
60
65
45
50
55
60
65
45
50
55
60
65
45
50
55
60
65
45
50
55
60
65
65
80
65
80
65
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
4
4
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
4
4
4
6
6
6
6
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CARBIDE
LF
DCON
Stock
MS4LTD0300T0130L40
MS4LTD0300T0200L25
MS4LTD0300T0200L40
3
3
3
1 30'
2
2
40
25
40
5.09
4.75
5.79
80
65
80
6
6
6
4
4
4
a
a
a
Type
1
1
1
SQUARE
DC_2
BALL
APMX
RADIUS
B7
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J365
MSTAR END MILLS

CARBIDE
MS4LT
Work material
AISI H13
Dia.
DC (mm)
Length of cut
APMX (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Depth of cut
ap (mm)
0.2
0.3
0.4
2
3
4
4
6
4
6
6
8
4
8
12
6
10
16
6
10
16
20
12
12
6
10
16
25
8
12
16
20
8
16
24
8
12
20
30
10
20
30
25
40
20000 40000
20000 40000
20000 40000
200 500
200 500
200 500
20000 40000
20000 40000
20000 36000
150 300
150 300
150 300
20000 38000
200 500
16000 29000
200 400
18000 32000
250 600
13000 24000
200 400
16000 27000
250 600
11000 20000
200 400
14000 24000
250 600
10000 18000
200 400
11000 19000
300 800
8000 14000
200 500
9200 16000
300 800
6600 12000
200 500
8500 15000
8000 14000
300 800
300 800
6100 11000
5700 10000
200 500
200 500
7500 13000
300 800
5300 9500
200 500
7000 12000
300 800
5000 9000
200 500
6200 11000
300 800
4400 8000
200 500
5500 9500
300 800
4000 7200
200 500
4400 7600
300 800
3200 5700
200 500
3700 6400
300 800
0.001
0.002
0.003
0.01
0.005
0.01
0.007
0.015
0.01
0.03
0.02
0.013
0.03
0.02
0.015
0.04
0.03
0.02
0.01
0.03
0.035
0.06
0.04
0.03
0.015
0.06
0.045
0.035
0.025
0.08
0.05
0.03
0.1
0.07
0.04
0.02
0.1
0.06
0.03
0.08
0.04
2700 4800
200 500
0.001
0.001
0.002
0.005
0.003
0.005
0.004
0.008
0.005
0.015
0.01
0.007
0.015
0.01
0.008
0.02
0.015
0.01
0.007
0.015
0.018
0.03
0.02
0.015
0.008
0.03
0.025
0.02
0.015
0.04
0.03
0.015
0.05
0.04
0.02
0.01
0.05
0.03
0.015
0.04
0.02
0.5
0.6
0.7
0.8
1.0
1.2
1.3
1.4
SOLID END MILLS

Pre-hardened steel
1.5
1.6
1.8
2.0
2.5
3.0
J366
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
B7
DC_2
(<30HRC)
( < 45HRC)
UWC
MS
Copper Alloy
30
CARBIDE
Aluminium Alloy
15
DCON(h6)
Type1
PRFRAD
APMX
B7
0.2<PRFRAD<1.5
Type2
PRFRAD
APMX
LF
5'
h6
BALL
0.01
DCON(h6)
DC_2
LF
SQUARE
MS2MTB
4 < DCON < 6

0
- 0.008
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.75
0.75
0.75
0.75
0.75
0.75
1
1
1
1
1
1
1
1
1.25
1.25
1.25
1.25
1.25
3
5
7
10
3
5
7
10
30'
1
1 30'
2
3
5
7
30'
1
1 30'
2
3
7
30'
1
1 30'
2
3
4
5
7
30'
1
1 30'
2
3
APMX
DC_2
LF
DCON
3
3
3
3
3
3
3
3
3
3
3
3
3
3
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
10
10
10
10
10
0.69
0.89
1.09
1.39
0.88
1.07
1.27
1.56
1.04
1.09
1.13
1.18
1.26
1.44
2.36
1.59
1.68
1.78
1.87
2.05
2.8
2.12
2.24
2.37
2.49
2.74
2.98
3.23
3.73
2.65
2.81
2.96
3.11
3.42
40
40
40
40
40
40
40
40
40
40
40
40
40
40
45
40
40
40
40
40
40
45
45
45
45
45
45
45
50
45
45
45
45
45
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
4
4
4
4
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TAPER
MS2MTBR0020T0300
MS2MTBR0020T0500
MS2MTBR0020T0700
MS2MTBR0020T1000
MS2MTBR0030T0300
MS2MTBR0030T0500
MS2MTBR0030T0700
MS2MTBR0030T1000
MS2MTBR0050T0030
MS2MTBR0050T0100
MS2MTBR0050T0130
MS2MTBR0050T0200
MS2MTBR0050T0300
MS2MTBR0050T0500
MS2MTBR0050T0700
MS2MTBR0075T0030
MS2MTBR0075T0100
MS2MTBR0075T0130
MS2MTBR0075T0200
MS2MTBR0075T0300
MS2MTBR0075T0700
MS2MTBR0100T0030
MS2MTBR0100T0100
MS2MTBR0100T0130
MS2MTBR0100T0200
MS2MTBR0100T0300
MS2MTBR0100T0400
MS2MTBR0100T0500
MS2MTBR0100T0700
MS2MTBR0125T0030
MS2MTBR0125T0100
MS2MTBR0125T0130
MS2MTBR0125T0200
MS2MTBR0125T0300
B7
SOLID END MILLS
PRFRAD
Stock
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute taper ball nose end mill.
J367
MSTAR END MILLS
MS2MTB
Order Number
PRFRAD
B7
APMX
DC_2
LF
DCON
Stock
Unit : mm
No. of
Flutes
SQUARE
CARBIDE
MS2MTBR0125T0400
MS2MTBR0125T0500
MS2MTBR0125T0700
MS2MTBR0150T0700
1.25
1.25
1.25
1.5
4
5
7
7
10
10
14.5
12.5
3.73
4.04
5.77
5.72
50
50
60
60
6
6
6
6
2
2
2
2
Type
a
a
a
1
1
2
2
SOLID END MILLS
TAPER
RADIUS
BALL


material
AISI H13
%>15
%<15
R
PRFRAD
(mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
R 0.1
R 0.15
R 0.2
R 0.25
R 0.3
R 0.4
R 0.5
R 0.75
R1
R 1.25
R 1.5
R2
R 2.5
R3
R4
R5
R6
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
32000
25000
21000
16000
13000
9000
300
500
1600
2400
3200
4800
5600
6500
6500
7000
7500
7500
6000
5800
4500
3600
2500
40000
40000
40000
40000
40000
40000
40000
40000
39000
33000
27000
20000
16000
13000
10000
8000
6000
250
350
1200
1400
1600
2400
3200
4000
4700
4500
4300
3600
2900
2600
2000
1700
1300
Depth of
cut
Depth of cut
(mm)
0.003
0.007
0.02
0.025
0.03
0.05
0.06
0.09
0.11
0.12
0.13
0.15
0.20
0.25
0.30
0.50
0.50
%>15
%<15
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
40000
40000
40000
40000
40000
40000
40000
40000
40000
36000
32000
25000
20000
17000
13000
10000
7200
300
500
1300
1900
2500
4000
5600
6500
6500
6500
6000
6000
5400
4700
3600
2900
2000
40000
40000
40000
40000
40000
40000
40000
32000
31000
26000
22000
16000
13000
10000
8000
6400
4800
250
350
950
1100
1300
1900
3000
3200
3500
3500
3400
2700
2300
2000
1500
1200
1000
Depth of cut
(mm)
0.003
0.007
0.015
0.020
0.025
0.04
0.05
0.08
0.11
0.12
0.13
0.15
0.20
0.25
0.30
0.50
0.50
<0.2PRFRAD
< Please
PRFRAD:Radius

End mill
pf
J368
ap
PRFRAD
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
B7
MS
Copper Alloy
DC_2
(<30HRC)
( < 45HRC)
UWC
20
CARBIDE
Aluminium Alloy
15
DCON(h6)
Type1
PRFRAD
APMX
LF
0.3<PRFRAD<1
0.03
BALL
5'
h6
SQUARE
MS4LTB
4 < DCON < 6

0
- 0.008
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
30'
30'
1
1
1 30'
1 30'
2
2
30'
30'
30'
1
1
1
1 30'
1 30'
1 30'
2
2
2
30'
30'
30'
30'
1
1
1
1
1 30'
1 30'
1 30'
1 30'
2
2
APMX
DC_2
LF
DCON
4
6
4
6
4
6
4
6
6
8
10
6
8
10
6
8
10
6
8
10
8
10
12
16
8
10
12
16
8
10
12
16
8
10
0.66
0.70
0.73
0.80
0.79
0.90
0.86
1.00
0.90
0.93
0.97
1.00
1.07
1.14
1.09
1.20
1.30
1.19
1.33
1.47
1.13
1.17
1.20
1.27
1.26
1.33
1.40
1.54
1.39
1.50
1.60
1.81
1.52
1.66
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
55
50
50
50
55
50
50
50
55
50
50
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TAPER
MS4LTBR0030T0030L04
MS4LTBR0030T0030L06
MS4LTBR0030T0100L04
MS4LTBR0030T0100L06
MS4LTBR0030T0130L04
MS4LTBR0030T0130L06
MS4LTBR0030T0200L04
MS4LTBR0030T0200L06
MS4LTBR0040T0030L06
MS4LTBR0040T0030L08
MS4LTBR0040T0030L10
MS4LTBR0040T0100L06
MS4LTBR0040T0100L08
MS4LTBR0040T0100L10
MS4LTBR0040T0130L06
MS4LTBR0040T0130L08
MS4LTBR0040T0130L10
MS4LTBR0040T0200L06
MS4LTBR0040T0200L08
MS4LTBR0040T0200L10
MS4LTBR0050T0030L08
MS4LTBR0050T0030L10
MS4LTBR0050T0030L12
MS4LTBR0050T0030L16
MS4LTBR0050T0100L08
MS4LTBR0050T0100L10
MS4LTBR0050T0100L12
MS4LTBR0050T0100L16
MS4LTBR0050T0130L08
MS4LTBR0050T0130L10
MS4LTBR0050T0130L12
MS4LTBR0050T0130L16
MS4LTBR0050T0200L08
MS4LTBR0050T0200L10
B7
SOLID END MILLS
PRFRAD
Stock
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 4 flute taper ball nose end mill for rib milling.
J369
MSTAR END MILLS
MS4LTB
PRFRAD
MS4LTBR0050T0200L12
MS4LTBR0050T0200L16
MS4LTBR0060T0030L08
MS4LTBR0060T0030L10
MS4LTBR0060T0030L12
MS4LTBR0060T0030L16
MS4LTBR0060T0100L08
MS4LTBR0060T0100L10
MS4LTBR0060T0100L12
MS4LTBR0060T0100L16
MS4LTBR0060T0130L08
MS4LTBR0060T0130L10
MS4LTBR0060T0130L12
MS4LTBR0060T0130L16
MS4LTBR0060T0200L08
MS4LTBR0060T0200L10
MS4LTBR0060T0200L12
MS4LTBR0060T0200L16
MS4LTBR0075T0030L08
MS4LTBR0075T0030L10
MS4LTBR0075T0030L12
MS4LTBR0075T0030L16
MS4LTBR0075T0030L20
MS4LTBR0075T0100L08
MS4LTBR0075T0100L10
MS4LTBR0075T0100L12
MS4LTBR0075T0100L16
MS4LTBR0075T0100L20
MS4LTBR0075T0130L08
MS4LTBR0075T0130L10
MS4LTBR0075T0130L12
MS4LTBR0075T0130L16
MS4LTBR0075T0130L20
MS4LTBR0075T0200L08
MS4LTBR0075T0200L10
MS4LTBR0075T0200L12
MS4LTBR0075T0200L16
MS4LTBR0075T0200L20
MS4LTBR0090T0030L08
MS4LTBR0090T0030L10
MS4LTBR0090T0030L12
MS4LTBR0090T0030L16
MS4LTBR0090T0030L20
MS4LTBR0090T0100L08
MS4LTBR0090T0100L10
MS4LTBR0090T0100L12
MS4LTBR0090T0100L16
MS4LTBR0090T0100L20
MS4LTBR0090T0130L08
MS4LTBR0090T0130L10
MS4LTBR0090T0130L12
MS4LTBR0090T0130L16
0.5
0.5
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
0.9
J370
B7
2
2
30'
30'
30'
30'
1
1
1
1
1 30'
1 30'
1 30'
1 30'
2
2
2
2
30'
30'
30'
30'
30'
1
1
1
1
1
1 30'
1 30'
1 30'
1 30'
1 30'
2
2
2
2
2
30'
30'
30'
30'
30'
1
1
1
1
1
1 30'
1 30'
1 30'
1 30'
APMX
DC_2
LF
DCON
Stock
Order Number
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
CARBIDE
12
16
8
10
12
16
8
10
12
16
8
10
12
16
8
10
12
16
8
10
12
16
20
8
10
12
16
20
8
10
12
16
20
8
10
12
16
20
8
10
12
16
20
8
10
12
16
20
8
10
12
16
1.80
2.08
1.33
1.36
1.40
1.47
1.46
1.53
1.60
1.74
1.59
1.69
1.80
2.01
1.72
1.86
2.00
2.28
1.63
1.66
1.70
1.77
1.84
1.75
1.82
1.89
2.03
2.17
1.88
1.98
2.09
2.30
2.51
2.01
2.15
2.29
2.57
2.84
1.92
1.96
1.99
2.06
2.13
2.05
2.12
2.19
2.33
2.47
2.17
2.28
2.38
2.59
50
55
50
50
50
55
50
50
50
55
50
50
50
55
50
50
50
55
50
50
50
55
60
50
50
50
55
60
50
50
50
55
60
50
50
50
55
60
50
50
50
55
60
50
50
50
55
60
50
50
50
55
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CARBIDE
LF
DCON
Stock
MS4LTBR0090T0130L20
MS4LTBR0090T0200L08
MS4LTBR0090T0200L10
MS4LTBR0090T0200L12
MS4LTBR0090T0200L16
MS4LTBR0090T0200L20
MS4LTBR0100T0030L10
MS4LTBR0100T0030L12
MS4LTBR0100T0030L16
MS4LTBR0100T0030L20
MS4LTBR0100T0030L25
MS4LTBR0100T0030L30
MS4LTBR0100T0100L10
MS4LTBR0100T0100L12
MS4LTBR0100T0100L16
MS4LTBR0100T0100L20
MS4LTBR0100T0100L25
MS4LTBR0100T0100L30
MS4LTBR0100T0130L10
MS4LTBR0100T0130L12
MS4LTBR0100T0130L16
MS4LTBR0100T0130L20
MS4LTBR0100T0130L25
MS4LTBR0100T0130L30
MS4LTBR0100T0200L10
MS4LTBR0100T0200L12
MS4LTBR0100T0200L16
MS4LTBR0100T0200L20
MS4LTBR0100T0200L25
MS4LTBR0100T0200L30
0.9
0.9
0.9
0.9
0.9
0.9
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1 30'
2
2
2
2
2
30'
30'
30'
30'
30'
30'
1
1
1
1
1
1
1 30'
1 30'
1 30'
1 30'
1 30'
1 30'
2
2
2
2
2
2
20
8
10
12
16
20
10
12
16
20
25
30
10
12
16
20
25
30
10
12
16
20
25
30
10
12
16
20
25
30
2.80
2.30
2.44
2.58
2.86
3.13
2.16
2.19
2.26
2.33
2.42
2.51
2.31
2.38
2.52
2.66
2.84
3.01
2.47
2.58
2.79
3.00
3.26
3.52
2.63
2.77
3.05
3.33
3.68
4.03
60
50
50
50
55
60
50
50
55
60
65
65
50
50
55
60
65
65
50
50
55
60
65
65
50
50
55
60
65
65
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
4
4
4
4
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SQUARE
DC_2
BALL
APMX
RADIUS
B7
TAPER
PRFRAD
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J371
MSTAR END MILLS

CARBIDE
MS4LTB
Work material
Length of cut
R
PRFRAD (mm) APMX (mm)
R0.3
R0.4
R0.5
R0.6
R0.75
SOLID END MILLS
R0.9
R1
4
6
6
8
10
8
10
12
16
8
10
12
16
8
10
12
16
20
8
10
12
16
20
10
12
16
20
25
30

Pre-hardened steel
AISI H13
Revolution
(min-1)
Feed rate
(mm/min)
18000 32000
250 600
14000 24000
250 600
11000 19000
300 800
9200 16000
300 800
7500 13000
300 800
6200 11000
300 800
5500 9500
300 800
Depth of cut
ap (mm)
0.01
0.007
0.025
0.02
0.015
0.025
0.02
0.018
0.015
0.035
0.03
0.027
0.02
0.05
0.04
0.035
0.03
0.02
0.08
0.07
0.06
0.05
0.04
0.08
0.07
0.05
0.04
0.03
0.02
Revolution
(min-1)
Feed rate
(mm/min)
13000 24000
200 400
10000 18000
200 400
8000 14000
200 500
6600 12000
200 500
5300 9500
200 500
4400 8000
200 500
4000 7200
200 500
Depth of cut
ap (mm)
0.005
0.004
0.013
0.01
0.008
0.013
0.01
0.009
0.008
0.018
0.015
0.013
0.01
0.025
0.02
0.018
0.015
0.01
0.04
0.035
0.035
0.03
0.02
0.045
0.04
0.03
0.02
0.015
0.01
J372
VC4STB
PRFRAD<0.5 PRFRAD > 0.5
Titanium Alloy,
Copper Alloy
B7
PRFRAD
APMX
LU
B2
LU_2
LF
B2
B7
PRFRAD
0.01
0
- 0.008
LU_2
0
- 0.009
B2
APMX
LU
PRFRAD
Type1
Type2
Type3
LF
B7
0.3<PRFRAD<4
DCON=6 8<DCON<10
h6
APMX
LU
Aluminium Alloy
SQUARE
Austenitic
Stainless Steel
BALL
Hardened Steel
(>55HRC)
DCON(h6)
Hardened Steel
( < 55HRC)
CARBIDE
DCON(h6)
30
DCON(h6)
(<30HRC)
( < 45HRC)
VC
UWC
LF
Relief Neck type.
PRFRAD
B7
APMX
LU
LU_2
B2
LF
DCON
Stock
VC4STBR0030T0130N05
VC4STBR0030T0200N05
VC4STBR0030T0500N05
VC4STBR0030T1000N15
VC4STBR0040T0130N10
VC4STBR0040T0130N15
VC4STBR0040T0200N10
VC4STBR0040T0500N10
VC4STBR0040T0700N10
VC4STBR0040T1000N15
VC4STBR0050T0130N10
VC4STBR0050T0130N15
VC4STBR0050T0130N20
VC4STBR0050T0200N10
VC4STBR0050T0200N15
VC4STBR0050T0200N20
VC4STBR0050T0500N10
VC4STBR0050T0500N15
VC4STBR0050T0500N20
VC4STBR0050T0700N10
VC4STBR0050T0700N15
VC4STBR0050T0700N20
VC4STBR0050T1000N14
VC4STBR0075T0200N10
VC4STBR0075T0500N15
VC4STBR0100T0130N10
VC4STBR0100T0130N15
VC4STBR0100T0130N20
VC4STBR0100T0200N06
VC4STBR0100T0200N10
VC4STBR0100T0200N15
VC4STBR0100T0500N10
VC4STBR0100T0500N15
VC4STBR0100T0500N23
0.3
0.3
0.3
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.75
0.75
1
1
1
1
1
1
1
1
1
1 30'
2
5
10
1 30'
1 30'
2
5
7
10
1 30'
1 30'
1 30'
2
2
2
5
5
5
7
7
7
10
2
5
1 30'
1 30'
1 30'
2
2
2
5
5
5
1
1
1
1
2
2
2
2
7
3
2
2
2
2
2
3
3
3
3
7
7
7
3
3
3
4
4
4
4
4
4
4
4
4
5
5
5
15
10
15
10
10
10
15
10
15
20
10
15
20
10
15
20
10
15
20
14
10
15
10
15
20
6
10
15
10
15
23
9.0
9.0
8.8
14.0
19.0
14.0
13.5
12.2
14.0
19.0
24.0
14.0
18.9
24.0
13.6
17.2
21.8
12.1
16.6
14.0
17.0
13.5
18.5
23.5
8.7
13.8
17.5
12.2
16.8
17.2
17.2
17.6
10.4
10.8
8.0
10.8
11.2
12.4
10.1
10.5
7.7
6.1
10.5
7.8
6.1
10.8
8.5
6.7
12.2
8.9
7.3
10.5
9.6
7.9
9.1
6.5
5.1
14.4
8.9
6.9
10.1
7.2
5.2
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
3
1
1
1
1
2
3
1
1
1
1
1
1
1
2
2
2
2
3
3
1
2
1
1
1
2
1
2
2
2
3
TAPER
Order Number
No. of
Flutes
Unit : mm
SOLID END MILLS
rigidity and high performance.
RADIUS
a 4 flute taper end mill with taper neck for maximum
J373
VC4STB
PRFRAD
B7
APMX
LU
LU_2
B2
LF
DCON
No. of
Flutes
Stock
VC4STBR0100T0700N17
VC4STBR0100T1000N12
VC4STBR0125T0500N15
VC4STBR0150T0130N15
VC4STBR0150T0130N20
VC4STBR0150T0300N15
VC4STBR0150T0500N10
VC4STBR0150T0500N18
VC4STBR0175T0500N15
VC4STBR0200T0130N15
VC4STBR0200T0130N20
VC4STBR0200T0300N21
VC4STBR0200T0500N13
VC4STBR0200T0700N18
VC4STBR0300T0130N15
VC4STBR0300T0130N20
VC4STBR0300T0300N22
VC4STBR0400T0130N15
VC4STBR0400T0300N22
1
1
1.25
1.5
1.5
1.5
1.5
1.5
1.75
2
2
2
2
2
3
3
3
4
4
7
10
5
1 30'
1 30'
3
5
5
5
1 30'
1 30'
3
5
7
1 30'
1 30'
3
1 30'
3
7
4
4
4
4
4
4
4
4
5
5
4
4
7
6
6
6
8
8
17
12
15
15
20
15
10
18
15
15
20
21
13
18
15
20
22
15
22
16.5
17.3
22.2
16.9
11.7
16.8
21.6
16.8
21.7
16.9
7.1
10.3
6.6
5.4
4.2
5.6
8.3
5.2
5.4
3.9
3.0
3.1
5.2
7.1
4.2
3.1
3.1
4.4
3.2
60
60
60
60
60
60
60
60
60
60
60
60
60
60
90
90
90
90
90
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
SOLID END MILLS
J374
Unit : mm
Order Number
TAPER
RADIUS
BALL
SQUARE
CARBIDE
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
3
3
2
2
2
2
2
3
3
2
2
3
3
3
2
2
3
2
3
CARBIDE

Pre-hardened steel
AISI H13
AISI D2
Work material
R 0.3
R 0.4
R 0.5
R 0.75
R1
R 1.25
R 1.5
R 1.75
130'
2
5
10
130'
130'
2
5
7
10
130
130'
130'
2
2
2
5
5
5
7
7
7
10
2
5
130'
130'
130'
2
2
2
5
5
5
7
10
5
130'
130'
3
5
5
5
5
5
5
15
10
15
10
10
10
15
10
15
20
10
15
20
10
15
20
10
15
20
14
10
15
10
15
20
6
10
15
10
15
23
17
12
15
15
20
15
10
18
15
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
38000
38000
38000
38000
38000
38000
38000
38000
38000
38000
38000
38000
38000
38000
38000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
32000
32000
32000
32000
32000
27500
1600
1600
1600
1600
2000
2000
2000
2000
2000
2000
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2800
2800
2800
2800
2800
2800
2800
2800
2800
2800
2800
2800
3000
3000
3000
3000
3000
3500
0.08
0.08
0.08
0.05
0.07
0.05
0.07
0.07
0.07
0.06
0.11
0.09
0.06
0.11
0.09
0.06
0.12
0.09
0.08
0.12
0.11
0.08
0.11
0.18
0.16
0.18
0.16
0.14
0.20
0.18
0.16
0.18
0.18
0.14
0.16
0.18
0.23
0.23
0.23
0.23
0.25
0.23
0.23
0.12
0.12
0.12
0.08
0.11
0.08
0.11
0.11
0.11
0.09
0.16
0.14
0.09
0.16
0.14
0.09
0.18
0.14
0.11
0.18
0.16
0.11
0.16
0.27
0.24
0.27
0.24
0.21
0.30
0.27
0.24
0.27
0.27
0.21
0.24
0.27
0.34
0.34
0.34
0.34
0.38
0.34
0.34
40000
40000
40000
40000
40000
40000
40000
40000
40000
40000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
35000
30000
30000
30000
30000
30000
30000
30000
30000
30000
30000
30000
30000
27000
27000
27000
27000
27000
23000
1200
1200
1200
1200
1500
1500
1500
1500
1500
1500
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1600
1800
1800
1800
1800
1800
1800
1800
1800
1800
1800
1800
1800
2000
2000
2000
2000
2000
2500
0.06
0.06
0.06
0.04
0.06
0.04
0.06
0.06
0.06
0.05
0.08
0.07
0.05
0.08
0.07
0.05
0.10
0.07
0.06
0.10
0.08
0.06
0.08
0.14
0.13
0.14
0.13
0.11
0.16
0.14
0.13
0.14
0.14
0.11
0.13
0.14
0.18
0.18
0.18
0.18
0.20
0.18
0.18
0.10
0.10
0.10
0.06
0.08
0.06
0.08
0.08
0.08
0.07
0.13
0.11
0.07
0.13
0.11
0.07
0.14
0.11
0.09
0.14
0.13
0.09
0.13
0.22
0.19
0.22
0.19
0.17
0.24
0.22
0.19
0.22
0.22
0.17
0.19
0.22
0.27
0.27
0.27
0.27
0.30
0.27
0.27
40000
40000
40000
40000
30000
30000
30000
30000
30000
30000
25000
25000
25000
25000
25000
25000
25000
25000
25000
25000
25000
25000
25000
18000
18000
15000
15000
15000
15000
15000
15000
15000
15000
15000
15000
15000
15000
16000
16000
16000
16000
16000
14000
700
700
700
700
700
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1200
1200
1200
1200
1200
1500
0.04
0.04
0.04
0.03
0.04
0.03
0.04
0.04
0.04
0.03
0.05
0.05
0.03
0.05
0.05
0.03
0.06
0.05
0.04
0.06
0.05
0.04
0.05
0.09
0.08
0.09
0.08
0.07
0.10
0.09
0.08
0.09
0.09
0.07
0.08
0.09
0.11
0.11
0.11
0.11
0.13
0.11
0.11
0.06
0.06
0.06
0.04
0.05
0.04
0.05
0.05
0.05
0.05
0.08
0.07
0.05
0.08
0.07
0.05
0.09
0.07
0.06
0.09
0.08
0.06
0.08
0.14
0.12
0.14
0.12
0.11
0.15
0.14
0.12
0.14
0.14
0.11
0.12
0.14
0.17
0.17
0.17
0.17
0.19
0.17
0.17
SOLID END MILLS
Taper angle Neck length Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut
R
one side
PRFRAD (mm)
LU (mm)
(min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm)
B7
ae
Depth of cut
ap
PRFRAD:Radius
J375

CARBIDE
VC4STB
Work material

Pre-hardened steel
AISI H13
AISI D2
Taper angle Neck length Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut Revolution Feed rate Depth of cut Depth of cut
R
one side
LU (mm)
PRFRAD (mm)
(min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm) (min-1) (mm/min) ap (mm) ae (mm)
B7
R2
R3
R4
130'
130'
3
5
7
130'
130'
3
130'
3
15
20
21
13
18
15
20
22
15
22
24000
24000
24000
24000
24000
16000
16000
16000
12000
12000
3500
3500
3500
3500
3500
3500
3500
3500
3500
3500
0.23
0.23
0.23
0.25
0.23
0.30
0.30
0.30
0.30
0.30
0.34
0.34
0.34
0.38
0.34
0.45
0.45
0.45
0.45
0.45
20000
20000
20000
20000
20000
13500
13500
13500
10000
10000
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
0.18
0.18
0.18
0.20
0.18
0.24
0.24
0.24
0.24
0.24
0.27
0.27
0.27
0.30
0.27
0.36
0.36
0.36
0.36
0.36
12000
12000
12000
12000
12000
8000
8000
8000
6000
6000
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
0.11
0.11
0.11
0.13
0.11
0.15
0.15
0.15
0.15
0.15
0.17
0.17
0.17
0.19
0.17
0.23
0.23
0.23
0.23
0.23
ae
Depth of cut
ap
PRFRAD:Radius
SOLID END MILLS
J376
MIRACLE END MILLS
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
Type1
DC
90
15
DC
LF
DC_2
90
DCON(h6)
APMX
LU
Type2
APMX
0.02
LF
h6
0
- 0.008
0
- 0.009
CARBIDE
Hardened Steel
( < 55HRC)
DC_2
DCON(h6)
(<30HRC)
( < 45HRC)
VC
SQUARE
UWC
BALL
VC2C
0
- 0.011
DC
DC_2
APMX
LU
LF
DCON
Stock
VC2CD0200
VC2CD0400
VC2CD0600
VC2CD0800
VC2CD1000
VC2CD1200
2
4
6
8
10
12
0.3
0.3
0.3
0.4
0.5
0.5
0.85
1.85
2.85
3.8
4.75
5.75
6
12
50
50
50
60
70
75
6
6
6
8
10
12
2
2
2
2
2
2
Type
1
1
2
2
2
2
a
a
a
a
a

Work
material


Pre-hardened steel

Titanium alloy
AISI H13
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
2
4
6
8
10
12
16000
8000
5300
4000
3200
2700
960
480
320
240
190
160
11000
5600
3700
2800
2200
1900
590
300
200
150
120
100
9500
4800
3200
2400
1900
1600
460
230
150
120
90
80
8000
4000
2700
2000
1600
1300
320
160
110
80
60
50
Depth of
cut
Chamfering
TAPER
Order Number
No. of
Flutes
Unit : mm
SOLID END MILLS
RADIUS
a Chamfering cutters for machining of hardened steel and
Chamfering of hole
< 0.3DC
< 0.2DC
(MAX. 2.5mm)
DC:Dia.
J377

HSS
1MA
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
25
HSS
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
SQUARE
DC
DCON
e
Type1
APMX
DC
LF
DCON
Type2
APMX
BALL
LF
3 < DC < 8
0
- 0.050
a Single flute end mill for aluminium channel and wood working.
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
1MAD0300
1MAD0400
1MAD0500
1MAD0600
1MAD0800
3
4
5
6
8
10
12
15
15
20
60
60
65
65
75
8
8
8
8
8
1
1
1
1
1
SOLID END MILLS
TAPER
RADIUS
Unit : mm
J378
a
a
a
a
Type
1
1
1
1
2
1LA
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
25
HSS
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
HSS
Copper Alloy
Aluminium Alloy
Type2
APMX
DC
LF
SQUARE
DCON
Type1
DCON
DC
APMX
BALL
LF
4 < DC < 12
0
- 0.050
APMX
LF
DCON
Stock
1LAD0400
1LAD0500
1LAD0600
1LAD0800
1LAD1000
1LAD1200
4
5
6
8
10
12
18
20
20
30
35
45
70
70
70
80
90
100
8
8
8
8
10
12
1
1
1
1
1
1
a
a
a
a
a
a
Type
1
1
1
2
2
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a Single flute end mill with longer cut length and overall length than standard for deeper machining.
J379
VIOLET END MILLS
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
SQUARE
DC
Hardened Steel
( < 55HRC)
30
BALL
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DCON
(<30HRC)
( < 45HRC)
KHA S
DCON
VA2SS
DCON
HSS
APMX
LF
3 < DC < 20
0
- 0.030
a 2 flute end mill with high grade HSS substrate and Violet coating for general use.
J380
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VA2SSD0300
VA2SSD0400
VA2SSD0500
VA2SSD0600
VA2SSD0700
VA2SSD0800
VA2SSD0900
VA2SSD1000
VA2SSD1100
VA2SSD1200
VA2SSD1300
VA2SSD1400
VA2SSD1500
VA2SSD1600
VA2SSD1700
VA2SSD1800
VA2SSD1900
VA2SSD2000
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
8
8
10
12
15
15
20
20
22
22
26
26
30
32
34
34
38
38
50
60
60
60
65
65
75
75
85
85
90
95
100
100
100
100
120
120
6
8
8
8
10
10
10
12
12
12
12
16
16
16
16
16
20
20
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
2
3
1
1
2
3
3
1
2
HSS
DC<3
Copper Alloy
Aluminium Alloy
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DC>3
APMX
LF
DC < 20
0
- 0.030
SQUARE
Titanium Alloy,
DCON
Austenitic
Stainless Steel
DCON
Hardened Steel
(>55HRC)
DC
Hardened Steel
( < 55HRC)
30
DCON
(<30HRC)
( < 45HRC)
KHA S
BALL
VA2MS
DC>20
0
- 0.040
APMX
LF
DCON
Stock
VA2MSD0300
VA2MSD0400
VA2MSD0500
VA2MSD0600
VA2MSD0700
VA2MSD0800
VA2MSD0900
VA2MSD1000
VA2MSD1100
VA2MSD1200
VA2MSD1300
VA2MSD1400
VA2MSD1500
VA2MSD1600
VA2MSD1700
VA2MSD1800
VA2MSD1900
VA2MSD2000
VA2MSD2200
VA2MSD2400
VA2MSD2500
VA2MSD2600
VA2MSD2800
VA2MSD3000
VA2MSD3200
VA2MSD3500
VA2MSD4000
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
24
25
26
28
30
32
35
40
10
12
15
15
20
20
25
25
30
30
35
35
40
40
40
40
45
45
45
50
50
50
55
55
60
60
65
50
60
60
60
65
65
75
75
85
85
90
95
100
100
100
100
120
120
120
140
140
140
145
145
160
160
165
6
8
8
8
10
10
10
10
12
12
12
16
16
16
16
16
20
20
20
25
25
25
25
25
32
32
32
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
1
2
3
1
1
2
3
3
1
2
3
1
2
3
3
3
2
3
3
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
J381
VIOLET END MILLS

HSS
VA2SS
VA2MS

y Side milling
Work
material

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2

Alloy steel, Tool steel
(35 40HRC)
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
25
30
40
5400
4300
3600
3200
2400
1900
1600
1200
950
760
640
470
170
200
210
220
240
260
240
210
180
150
130
100
4000
3200
2700
2400
1800
1400
1200
900
720
570
480
350
125
150
160
165
180
190
180
160
135
115
100
75
2700
2100
1800
1600
1200
950
800
600
480
380
320
240
85
100
105
110
120
130
120
105
90
75
65
50
2200
1800
1500
1300
1000
800
660
500
400
320
270
200
65
75
80
85
90
100
90
80
70
60
50
40
< 0.2DC
Depth of
cut
< 1.5DC
DC:Dia.
SOLID END MILLS
y Slotting
Work
material

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2

(35 40HRC)
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
25
30
40
3700
3200
2900
2600
2000
1600
1300
1000
720
570
480
360
110
140
160
170
190
210
190
170
130
110
90
70
3000
2800
2400
2100
1600
1300
1100
800
640
450
370
280
95
130
145
150
160
180
165
140
120
90
75
60
2100
1800
1500
1300
1000
800
660
500
400
320
270
200
65
75
80
85
90
100
90
80
70
60
50
40
1600
1400
1200
1000
800
640
530
400
320
230
190
140
50
60
60
70
70
80
70
65
55
40
35
25
DC
Depth of
cut
< 0.5DC
(MAX. 10mm)
DC:Dia.
1) Supply cutting fluid sufficiently during slotting. When dry cut, slotting decrease the revolution and feed rate by 20 30% proportionately.
2) When drilling, please set the feed rate at 1/3 or below of the values above.
J382
TWO-FLUTE END MILLS

DC<3
Copper Alloy
Aluminium Alloy
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DC > 3
APMX
LF
DC < 3
0
- 0.020
SQUARE
Titanium Alloy,
DCON
Austenitic
Stainless Steel
DCON
Hardened Steel
(>55HRC)
DC
Hardened Steel
( < 55HRC)
HSS
DCON
(<30HRC)
( < 45HRC)
30
CO HSS
BALL
2SS
DC>3
0
- 0.030
APMX
LF
DCON
Stock
2SSD0050
2SSD0100
2SSD0150
2SSD0200
2SSD0250
2SSD0300
2SSD0350
2SSD0400
2SSD0450
2SSD0500
2SSD0550
2SSD0600
2SSD0650
2SSD0700
2SSD0750
2SSD0800
2SSD0850
2SSD0900
2SSD0950S10
2SSD0950S12
2SSD1000S10
2SSD1000S12
2SSD1050
2SSD1100
2SSD1150
2SSD1200
2SSD1250
2SSD1300
2SSD1350
2SSD1400
2SSD1450
2SSD1500
2SSD1550
2SSD1600
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
9.5
10
10
10.5
11
11.5
12
12.5
13
13.5
14
14.5
15
15.5
16
0.8
2
3.5
5
6
8
8
8
10
10
12
12
15
15
15
15
20
20
20
20
20
20
22
22
22
22
26
26
26
26
26
30
32
32
50
50
50
50
50
50
60
60
60
60
60
60
65
65
65
65
75
75
75
75
75
75
85
85
85
85
90
90
90
90
100
100
100
100
6
6
6
6
6
6
8
8
8
8
8
8
10
10
10
10
10
10
10
12
10
12
12
12
12
12
12
12
16
16
16
16
16
16
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
2
3
3
1
1
1
1
1
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute HSS end mill with rigid design.
J383
TWO-FLUTE END MILLS
2SS
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
BALL
SQUARE
HSS
2SSD1650
2SSD1700
2SSD1750
2SSD1800
2SSD1850
2SSD1900
2SSD1950
2SSD2000
16.5
17
17.5
18
18.5
19
19.5
20
32
34
34
34
38
38
38
38
100
100
100
100
115
115
115
115
16
16
16
16
20
20
20
20
2
2
2
2
2
2
2
2
Type
3
3
3
3
1
1
1
2
a
a
a
a
a
a
a
SOLID END MILLS
TAPER
RADIUS

Work
material
Structural steel,
Carbon steel
Austenitic
stainless steel
Cast iron
AISI 304, AISI 316
AISI No 35 B
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
60 (50)
80 (65)
85 (70)
90 (75)
100 (85)
110 (95)
120 (100)
130 (110)
140 (120)
130 (110)
110 (95)
100 (80)
7000
4200
2600
1800
1400
1200
1000
800
640
530
400
320
40 (35)
50 (40)
60 (50)
65 (55)
70 (60)
90 (75)
90 (75)
95 (80)
100 (80)
95 (80)
85 (70)
70 (60)
4500
3000
1800
1400
1100
900
780
580
470
390
300
240
30 (25)
35 (30)
50 (40)
55 (45)
55 (45)
60 (50)
65 (55)
65 (55)
65 (55)
60 (50)
55 (45)
45 (38)
3500
2400
1400
1100
850
710
610
470
380
310
230
190
25 (20)
27 (22)
30 (25)
35 (30)
35 (30)
40 (35)
50 (40)
50 (40)
55 (45)
50 (40)
40 (35)
35 (30)
7500
4500
2700
2000
1600
1300
1100
850
700
580
440
350
65 (55)
85 (70)
90 (75)
95 (80)
110 (90)
120 (100)
130 (110)
140 (120)
160 (130)
140 (120)
120 (100)
100 (85)
16000
11000
6800
4800
3800
3200
2800
2200
1800
1600
1200
960
120 (100)
170 (140)
190 (150)
240 (190)
310 (250)
360 (290)
400 (320)
460 (370)
440 (350)
420 (340)
350 (280)
300 (240)
AISI 1045, AISI 1050
Dia.
Revolution
DC (mm)
(min-1)
0.5
1
2
3
4
5
6
8
10
12
16
20

Carbon steel,
Alloy steel (20 30HRC) Pre-hardened steel
(30 35HRC)
AISI 1055, AISI P20
AISI H13
8000
5300
3100
2300
1800
1600
1400
1100
860
720
540
430
< 0.1DC
Depth of
cut
< 0.2DC
(DC < & 3)

(DC > & 3)
Aluminium alloy
DC
(DC < & 2)
(& 2 < DC < & 3)
< 0.5DC (DC> & 3)
< 0.1DC
< 1.5DC
< 0.3DC
DC:Dia.
J384
TWO-FLUTE END MILLS

DC<3
Copper Alloy
Aluminium Alloy
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DC>3
APMX
LF
DC < 3
0
- 0.020
3<DC < 20
0
- 0.030
SQUARE
Titanium Alloy,
DCON
Austenitic
Stainless Steel
DCON
Hardened Steel
(>55HRC)
DC
Hardened Steel
( < 55HRC)
HSS
DCON
(<30HRC)
( < 45HRC)
30
KHA S
BALL
S2MD
DC>20
0
- 0.040
APMX
LF
DCON
Stock
S2MDD0050
S2MDD0100
S2MDD0150
S2MDD0200
S2MDD0250
S2MDD0300
S2MDD0350
S2MDD0400
S2MDD0450
S2MDD0500
S2MDD0550
S2MDD0600
S2MDD0650
S2MDD0700
S2MDD0750
S2MDD0800S08
S2MDD0800S10
S2MDD0850
S2MDD0900
S2MDD0950
S2MDD1000S10
S2MDD1000S12
S2MDD1050
S2MDD1100
S2MDD1150
S2MDD1200
S2MDD1250
S2MDD1300
S2MDD1350
S2MDD1400
S2MDD1450
S2MDD1500
S2MDD1550
S2MDD1600
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8
8.5
9
9.5
10
10
10.5
11
11.5
12
12.5
13
13.5
14
14.5
15
15.5
16
0.8
2
3.5
5
6
8
8
8
10
10
12
12
15
15
15
15
15
20
20
20
20
20
22
22
22
22
26
26
26
26
26
30
32
32
50
50
50
50
50
50
60
60
60
60
60
60
65
65
65
65
65
75
75
75
75
75
85
85
85
85
90
90
95
95
100
100
100
100
6
6
6
6
6
6
8
8
8
8
8
8
10
10
10
8
10
10
10
12
10
12
12
12
12
12
12
12
16
16
16
16
16
16
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
2
3
3
1
1
1
1
1
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute end mill with KHA Super substrate for high speed milling of difficult-to-cut and hard materials.
J385
TWO-FLUTE END MILLS
S2MD
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
BALL
SQUARE
HSS
S2MDD1650
S2MDD1700
S2MDD1750
S2MDD1800
S2MDD1850
S2MDD1900
S2MDD1950
S2MDD2000
16.5
17
17.5
18
18.5
19
19.5
20
32
34
34
34
38
38
38
38
100
100
100
100
120
120
120
120
16
16
16
16
20
20
20
20
2
2
2
2
2
2
2
2
Type
3
3
3
3
1
1
1
2
a
a
a
a
a
a
a
SOLID END MILLS
TAPER
RADIUS

Work
material
Austenitic stainless steel, Cast iron

(35 40HRC)
AISI 304, AISI 316
AISI No 35 B
Aluminium alloy
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
100 (80)
140 (110)
145 (115)
150 (120)
170 (135)
190 (150)
200 (160)
220 (175)
240 (190)
220 (175)
190 (150)
170 (135)
12000
7100
4400
3100
2400
2000
1700
1300
1100
900
680
540
70 (55)
85 (70)
100 (80)
110 (90)
120 (95)
150 (120)
150 (120)
160 (130)
180 (145)
160 (130)
145 (115)
120 (95)
7700
5100
3100
2400
1850
1500
1300
990
800
670
500
400
50 (40)
60 (50)
85 (70)
95 (75)
95 (75)
100 (80)
110 (90)
110 (90)
110 (90)
100 (80)
85 (70)
75 (60)
6000
4100
2400
1900
1450
1200
1000
800
650
540
400
320
40 (30)
45 (35)
50 (40)
60 (50)
60 (50)
70 (55)
85 (70)
85 (70)
90 (70)
85 (70)
70 (55)
60 (50)
13000
7700
4600
3400
2700
2200
1900
1450
1200
990
760
600
110 (90)
145 (115)
150 (120)
160 (130)
190 (150)
200 (160)
220 (175)
240 (190)
270 (220)
240 (190)
200 (160)
170 (135)
20000
19000
12000
8200
6500
5400
4800
3800
3200
2700
2000
1600
160 (130)
290 (230)
320 (260)
410 (330)
530 (420)
610 (490)
680 (540)
780 (620)
750 (600)
710 (570)
600 (480)
510 (410)
Dia.
Revolution
DC (mm)
(min-1)
0.5
1
2
3
4
5
6
8
10
12
16
20

Carbon steel,
(30 35HRC)
AISI 1055, AISI P20
AISI H13
Structural steel,
Carbon steel
14000
9000
5300
3900
3100
2700
2400
1900
1500
1250
940
750
< 0.1DC
Depth of
cut
< 0.2DC
(DC < & 3)

(DC > & 3)
DC
< 1.5DC
(DC < & 2)

(& 2 < DC < & 3)
< 0.5DC (DC> & 3)
< 0.1DC
< 0.3DC
DC:Dia.
J386
HSS
DC<3
Copper Alloy
Aluminium Alloy
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DC>3
APMX
LF
DC < 20
0
- 0.030
SQUARE
Titanium Alloy,
DCON
Austenitic
Stainless Steel
DCON
Hardened Steel
(>55HRC)
DC
Hardened Steel
( < 55HRC)
30
DCON
(<30HRC)
( < 45HRC)
CO HSS
BALL
G2MS
DC>20
0
- 0.040
APMX
LF
DCON
Stock
G2MSD0100
G2MSD0150
G2MSD0200
G2MSD0250
G2MSD0300
G2MSD0350
G2MSD0400
G2MSD0450
G2MSD0500
G2MSD0550
G2MSD0600
G2MSD0650
G2MSD0700
G2MSD0750
G2MSD0800
G2MSD0850
G2MSD0900
G2MSD0950
G2MSD1000
G2MSD1100
G2MSD1200
G2MSD1300
G2MSD1400
G2MSD1500
G2MSD1600
G2MSD1700
G2MSD1800
G2MSD1900
G2MSD2000
G2MSD2100
G2MSD2200
G2MSD2300
G2MSD2400
G2MSD2500
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
3
4.5
6
7.5
10
12
12
15
15
15
15
20
20
20
20
25
25
25
25
30
30
35
35
40
40
40
40
45
45
45
45
50
50
50
50
50
50
50
50
50
50
55
55
55
55
65
65
65
65
75
75
75
75
85
85
90
95
100
100
100
100
115
115
115
115
120
120
120
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
16
16
16
16
16
20
20
20
20
25
25
25
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
3
1
1
2
3
3
1
2
3
3
1
1
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute end mill with high grade HSS substrate and TiN coating for general use.
J387
TWO-FLUTE END MILLS
G2MS
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
RADIUS
BALL
SQUARE
HSS
G2MSD2600
G2MSD2700
G2MSD2800
G2MSD2900
G2MSD3000
G2MSD3100
G2MSD3200
G2MSD3300
G2MSD3400
G2MSD3500
G2MSD3600
G2MSD3700
G2MSD3800
G2MSD3900
G2MSD4000
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
50
55
55
55
55
60
60
60
60
60
65
65
65
65
65
120
125
125
125
125
145
145
145
145
145
150
150
150
150
150
25
25
25
25
25
25
32
32
32
32
32
32
32
32
32
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Type
3
3
3
3
3
3
2
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
a
a
a
a
SOLID END MILLS
TAPER

Work
material
Structural steel,
Carbon steel
Austenitic
stainless steel
Cast iron
AISI 304, AISI 316
AISI No 35 B
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
80 (65)
85 (70)
90 (70)
100 (80)
115 (90)
120 (95)
130 (105)
145 (115)
130 (105)
115 (90)
95 (75)
85 (70)
80 (65)
60 (50)
5000
3100
2200
1700
1450
1200
960
770
640
480
380
300
250
180
50 (40)
60 (50)
65 (50)
70 (55)
90 (70)
90 (70)
95 (75)
110 (90)
95 (75)
90 (70)
70 (55)
60 (50)
55 (45)
35 (30)
3600
2200
1700
1300
1100
940
700
560
470
360
290
230
190
140
35 (30)
50 (40)
55 (45)
55 (45)
60 (50)
65 (50)
65 (50)
65 (50)
60 (50)
55 (45)
45 (35)
40 (30)
35 (30)
25 (20)
2900
1700
1300
1000
850
730
560
460
370
280
230
180
145
110
25 (20)
30 (25)
35 (30)
35 (30)
40 (30)
50 (40)
50 (40)
55 (45)
50 (40)
40 (30)
35 (30)
30 (25)
25 (20)
22 (18)
5400
3200
2400
1900
1600
1300
1000
840
700
530
420
340
290
220
85 (70)
90 (70)
95 (75)
110 (90)
120 (95)
130 (105)
140 (110)
160 (130)
140 (110)
120 (95)
100 (80)
90 (70)
85 (70)
65 (50)
13000
8200
5800
4600
3800
3400
2600
2200
1900
1450
1150
910
770
580
170 (135)
190 (150)
240 (190)
310 (250)
360 (290)
400 (320)
460 (370)
430 (350)
420 (340)
350 (280)
300 (240)
260 (210)
240 (190)
190 (150)
Dia.
Revolution
DC (mm)
(min-1)
1
2
3
4
5
6
8
10
12
16
20
25
30
40

Carbon steel,
(30 35HRC)
AISI 1055, AISI P20
AISI P20, AISI H13
AISI D2
6400
3700
2800
2150
1900
1700
1300
1000
860
650
520
420
350
250
< 0.1DC
Depth of
cut
< 0.2DC
(DC < & 3)

(DC > & 3)
Aluminium alloy
DC
< 1.5DC
(DC < & 2)

(& 2 < DC < & 3)
< 0.5DC (DC> & 3)
< 0.1DC
< 0.3DC
DC:Dia.
J388
DC<3
Copper Alloy
Aluminium Alloy
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DC>3
APMX
LF
DC < 3
0
- 0.020
3<DC < 20
0
- 0.030
SQUARE
Titanium Alloy,
DCON
Austenitic
Stainless Steel
DCON
Hardened Steel
(>55HRC)
DC
Hardened Steel
( < 55HRC)
HSS
DCON
(<30HRC)
( < 45HRC)
30
CO HSS
BALL
2MS
DC>20
0
- 0.040
APMX
LF
DCON
Stock
2MSD0100
2MSD0150
2MSD0200
2MSD0250
2MSD0300
2MSD0350
2MSD0400
2MSD0450
2MSD0500
2MSD0550
2MSD0600
2MSD0650
2MSD0700
2MSD0750
2MSD0800
2MSD0850
2MSD0900
2MSD0950
2MSD1000
2MSD1100
2MSD1200
2MSD1300
2MSD1400
2MSD1500
2MSD1600
2MSD1700
2MSD1800
2MSD1900
2MSD2000
2MSD2100
2MSD2200
2MSD2300
2MSD2400
2MSD2500
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
3
4.5
6
7.5
10
12
12
15
15
15
15
20
20
20
20
25
25
25
25
30
30
35
35
40
40
40
40
45
45
45
45
50
50
50
50
50
50
50
50
50
50
55
55
55
55
65
65
65
65
75
75
75
75
85
85
90
95
100
100
100
100
115
115
115
115
120
120
120
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
16
16
16
16
16
20
20
20
20
25
25
25
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
2
3
1
1
2
3
3
1
2
3
3
1
1
2
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute end mill with high grade HSS substrate for general use.
J389
TWO-FLUTE END MILLS
2MS
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
2MSD2600
2MSD2700
2MSD2800
2MSD2900
2MSD3000
2MSD3100
2MSD3200
2MSD3300
2MSD3400
2MSD3500
2MSD3600
2MSD3700
2MSD3800
2MSD3900
2MSD4000
2MSD4100
2MSD4200S32
2MSD4200S42
2MSD4500S32
2MSD4500S42
2MSD4600S32
2MSD4600S42
2MSD5000S32
2MSD5000S42
2MSD5500
2MSD6000
J390
DC
APMX
LF
DCON
Stock
Order Number
Unit : mm
No. of
Flutes
HSS
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
42
45
45
46
46
50
50
55
60
50
55
55
55
55
60
60
60
60
60
65
65
65
65
65
70
70
70
70
70
70
70
70
70
80
85
120
125
125
125
125
145
145
145
145
145
150
150
150
150
150
155
155
155
155
155
155
155
155
155
175
185
25
25
25
25
25
25
32
32
32
32
32
32
32
32
32
32
32
42
32
42
32
42
32
42
42
42
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
3
3
3
3
3
3
2
3
3
3
3
3
3
3
3
3
3
2
3
3
3
3
3
3
3
3
DC<3
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
DC>3
Aluminium Alloy
u
Type1
DCON
DC
Hardened Steel
( < 55HRC)
HSS
APMX
LF
DCON
DC
Type2
APMX
LF
DCON
DC
Type3
APMX
DC < 3
0
- 0.020
3<DC < 20
0
- 0.030
LF
DC>20
SQUARE
(<30HRC)
( < 45HRC)
30
CO HSS
BALL
2LS
0
- 0.040
APMX
LF
DCON
Stock
2LSD0100
2LSD0150
2LSD0200
2LSD0250
2LSD0300
2LSD0350
2LSD0400
2LSD0450
2LSD0500
2LSD0550
2LSD0600
2LSD0650
2LSD0700
2LSD0750
2LSD0800
2LSD0850
2LSD0900
2LSD0950
2LSD1000
2LSD1050
2LSD1100
2LSD1150
2LSD1200
2LSD1250
2LSD1300
2LSD1350
2LSD1400
2LSD1450
2LSD1500
2LSD1550
2LSD1600
2LSD1650
2LSD1700
2LSD1750
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
10.5
11
11.5
12
12.5
13
13.5
14
14.5
15
15.5
16
16.5
17
17.5
6
7.5
10
15
15
15
20
20
25
25
25
35
35
35
35
35
45
45
45
55
55
55
55
55
55
55
55
65
65
65
65
65
65
65
50
50
55
55
55
55
55
55
60
60
60
75
75
75
75
75
90
90
90
105
105
105
105
105
105
110
110
120
120
120
120
120
120
120
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
2
3
3
1
1
1
1
1
2
3
3
3
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 flute end mill with high grade HSS substrate for general use.
J391
TWO-FLUTE END MILLS
2LS
J392
DC
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
Order Number
2LSD1800
2LSD1850
2LSD1900
2LSD1950
2LSD2000
2LSD2100
2LSD2200
2LSD2300
2LSD2400
2LSD2500
2LSD2600
2LSD2700
2LSD2800
2LSD2900
2LSD3000
2LSD3100
2LSD3200
2LSD3300
2LSD3400
2LSD3500
2LSD3600
2LSD3700
2LSD3800
2LSD3900
2LSD4000
18
18.5
19
19.5
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
65
75
75
75
75
75
75
90
90
90
90
90
90
90
90
95
95
95
100
100
105
105
105
110
110
120
140
140
140
140
140
140
160
160
160
160
160
160
160
160
180
180
180
185
185
190
190
190
195
195
16
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
32
32
32
32
32
32
32
32
32
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
SOLID END MILLS
TAPER
RADIUS
BALL
SQUARE
HSS
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
3
1
1
1
2
3
3
1
1
2
3
3
3
3
3
3
2
3
3
3
3
3
3
3
3
2MS
1)
2LS
HSS

Work
material
5300
3100
2300
1800
1600
1400
1100
860
720
540
430
350
290
210
160
130
(2MS)
Depth of
cut
Austenitic
stainless steel
Cast iron
AISI 304, AISI 316
AISI No 35 B
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
65 (50)
70 (55)
75 (60)
85 (70)
95 (75)
100 (80)
110 (90)
120 (95)
110 (90)
95 (75)
80 (65)
70 (55)
65 (50)
50 (40)
40 (30)
35 (28)
4200
2600
1800
1400
1200
1000
800
640
530
400
320
250
210
150
115
95
40 (30)
50 (40)
55 (45)
60 (50)
75 (60)
75 (60)
80 (65)
85 (70)
80 (65)
75 (60)
60 (50)
50 (40)
45 (35)
30 (25)
28 (22)
25 (20)
3000
1800
1400
1100
900
780
580
470
390
300
240
190
160
120
90
75
30 (25)
40 (30)
45 (35)
45 (35)
50 (40)
55 (45)
55 (45)
55 (45)
50 (40)
45 (35)
38 (30)
32 (25)
28 (22)
22 (18)
20 (15)
18 (15)
2400
1400
1100
850
710
610
470
380
310
230
190
150
120
90
70
55
22 (18)
25 (20)
30 (25)
30 (25)
35 (25)
40 (30)
40 (30)
45 (35)
40 (30)
35 (28)
30 (25)
25 (20)
22 (18)
18 (15)
15 (12)
12 (10)
4500
2700
2000
1600
1300
1100
850
700
580
440
350
285
240
180
140
115
70 (55)
75 (60)
80 (65)
90 (70)
100 (80)
110 (90)
115 (90)
130 (105)
115 (90)
100 (80)
85 (70)
75 (60)
70 (55)
55 (45)
45 (35)
40 (30)
11000
6800
4800
3800
3200
2800
2200
1800
1600
1200
960
760
640
480
380
310
140 (110)
160 (130)
200 (160)
260 (210)
300 (240)
330 (260)
380 (300)
360 (290)
350 (280)
290 (230)
250 (200)
220 (180)
200 (160)
160 (130)
130 (105)
110 (90)
Dia.
Revolution
DC (mm)
(min-1)
1
2
3
4
5
6
8
10
12
16
20
25
30
40
50
60

Carbon steel,
(30 35HRC)
AISI 1055, AISI P20
AISI H13
Structural steel,
Carbon steel
< 0.1DC
< 0.2DC
(DC < & 3)

(DC > & 3)
Aluminium alloy
DC
< 1.5DC
(DC < & 2)

(& 2 < DC < & 3)
< 0.5DC (DC> & 3)
< 0.1DC
< 0.3DC
1) Decrease the revolution by 20 30% and the feed rate by 40 50% for 2LS.
SOLID END MILLS
DC:Dia.
J393
TWO-FLUTE END MILLS
2MK
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
SQUARE
DC
Hardened Steel
( < 55HRC)
DCON
(<30HRC)
( < 45HRC)
15
CO HSS
Type1
DCON
HSS
Type2
APMX
DC
LF
APMX
BALL
LF
2MKP(DC+0.02
0 )
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
a 2 flute end mill for NN (JIS) standards and plus or minus tolerance diameters.
2MKPD0300
2MKPD0400
2MKPD0500
2MKPD0600
2MKPD0700
2MKPD0800
2MKPD1000
2MKPD1200
2MKPD1500
2MKPD1800
2MKPD2000
3
4
5
6
7
8
10
12
15
18
20
5
6
8
8
10
10
15
18
22
22
22
50
60
60
60
65
65
75
75
75
80
85
6
8
8
8
10
10
12
12
16
20
20
2
2
2
2
2
2
2
2
2
2
2
J394
1
1
1
1
1
1
1
2
1
1
2
a
a
a
a
a
a
a
a
a
a
0
)
2MKN(DC-0.02
DC
APMX
LF
DCON
No. of
Flutes
Stock
Unit : mm
Order Number
2MKND0300
2MKND0400
2MKND0500
2MKND0600
2MKND0700
2MKND0800
2MKND1000
2MKND1200
2MKND1500
3
4
5
6
7
8
10
12
15
5
6
8
8
10
10
15
18
22
50
60
60
60
65
65
75
75
75
6
8
8
8
10
10
12
12
16
2
2
2
2
2
2
2
2
2
Type
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
1
HSS
2MKNN(DC-0.02
-0.04 )
Stock
2MKNND0300
2MKNND0400
2MKNND0500
2MKNND0600
2MKNND0700
2MKNND0800
2MKNND1000
2MKNND1200
2MKNND1500
2MKNND1800
2MKNND2000
3
4
5
6
7
8
10
12
15
18
20
5
6
8
8
10
10
15
18
22
22
22
50
60
60
60
65
65
75
75
75
80
85
6
8
8
8
10
10
12
12
16
20
20
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
1
1
2
SQUARE
DCON
BALL
LF
RADIUS
APMX
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
J395
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
SQUARE
BALL
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DCON
Hardened Steel
( < 55HRC)
DC
(<30HRC)
( < 45HRC)
37.5
KHA S
DCON
S2SDA
DCON
HSS
APMX
DC=3
0
- 0.020
LF
DC>3
0
- 0.030
a 2 flute end mill for aluminium alloy and soft materials.
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
S2SDAD0300
S2SDAD0400
S2SDAD0500
S2SDAD0600
S2SDAD0800
S2SDAD1000
S2SDAD1200
S2SDAD1400
S2SDAD1600
S2SDAD1800
S2SDAD2000
3
4
5
6
8
10
12
14
16
18
20
8
8
10
12
15
20
22
26
32
34
38
50
60
60
60
65
75
85
90
100
100
115
6
8
8
8
10
10
12
16
16
16
20
2
2
2
2
2
2
2
2
2
2
2
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
2
2
1
2
3
2

Work
material
Cast aluminium, Rolled aluminium,

Magnesium alloy resin
AC, ADC, A5052, A7075
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
6
8
10
12
16
20
8200
6500
4800
3800
3200
2700
2000
1600
410
530
680
780
750
710
600
510
DC
Depth of
cut
< 1DC
DC:Dia.
J396
VIOLET END MILLS
VAMH
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
KHA S
45
50
DC>6
DC=5
Hardened Steel
(>55HRC)
HSS
DC=5
Austenitic
Stainless Steel
Titanium Alloy,
DC<20
Copper Alloy
DC>21
Aluminium Alloy
Type2
APMX
DC
LF
SQUARE
DCON
Type1
DCON
DC
15
APMX
BALL
LF
5 < DC < 30
0
- 0.040
APMX
LF
DCON
Stock
VAMHD0500
VAMHD0600
VAMHD0700
VAMHD0800
VAMHD0900
VAMHD1000
VAMHD1100
VAMHD1200
VAMHD1300
VAMHD1400
VAMHD1500
VAMHD1600
VAMHD1800
VAMHD2000
VAMHD2100
VAMHD2200
VAMHD2300
VAMHD2400
VAMHD2500
VAMHD2800
VAMHD3000
5
6
7
8
9
10
11
12
13
14
15
16
18
20
21
22
23
24
25
28
30
12
15
20
20
25
25
30
30
35
35
40
40
40
45
45
45
50
50
50
55
55
65
65
75
75
90
90
95
95
105
105
115
115
125
130
135
135
140
140
140
150
150
8
8
10
10
10
12
12
12
16
16
16
16
20
20
25
25
25
25
25
32
32
2
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
1
1
1
2
1
2
1
1
1
1
2
1
1
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 4 flute end mill with high grade HSS substrate and Violet coating for general use.
J397
VIOLET END MILLS

HSS
VAMH
y Side milling
Work
material

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2

(35 40HRC)
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
25
30
3600
3200
2400
1900
1600
1200
950
760
640
140
200
220
230
240
220
200
220
200
2700
2400
1800
1400
1200
900
720
570
480
100
150
160
170
180
160
150
170
150
1800
1600
1200
960
800
600
480
380
320
70
100
110
120
120
110
100
110
100
1500
1300
1000
800
660
500
400
320
270
60
80
90
100
100
90
85
95
85
< 0.3DC
Depth of
cut
< 1.5DC
DC:Dia.
y Slotting
SOLID END MILLS
Work
material

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2

(35 40HRC)
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
25
30
2900
2600
2000
1600
1300
1000
720
570
480
105
150
165
170
180
165
150
165
150
2400
2100
1600
1300
1100
800
640
450
370
75
110
120
130
135
120
110
130
110
1500
1300
1000
800
660
500
400
320
270
50
75
80
90
90
80
75
80
75
1200
1000
800
640
530
400
320
230
190
45
60
70
75
75
70
65
70
65
DC
Depth of
cut
< 0.5DC
DC:Dia.
1) Supply cutting fluid sufficiently during slotting. When slotting with dry cut, decrease the revolution and feed rate proportionately by 20 30%.
J398
HIGH HELIX END MILLS
KMH
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
45
KHA
50
DC=5
HSS
DC>6
DC=5
DC<20
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
Type2
APMX
DC
LF
SQUARE
DCON
Type1
DCON
DC
15
APMX
BALL
LF
5 < DC < 20
0
- 0.040
APMX
LF
DCON
Stock
KMHD0500
KMHD0600
KMHD0700
KMHD0800
KMHD0900
KMHD1000
KMHD1200
KMHD1400
KMHD1600
KMHD2000
5
6
7
8
9
10
12
14
16
20
12
15
20
20
25
25
30
35
40
45
65
65
75
75
90
90
95
105
115
130
8
8
10
10
10
12
12
16
16
20
2
3
3
3
3
3
3
3
3
3
Type
1
1
1
1
1
1
2
1
2
2
a
a
a
a
a
a
a
a
a

Work
material

Carbon steel

(20 30HRC)

Austenitic stainless steel
AISI 1055, AISI P20
AISI H13, AISI D2
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
1600
1400
1100
860
720
540
430
65
90
100
105
110
100
90
1200
1000
800
640
530
400
320
50
65
75
80
80
75
65
900
780
580
470
390
300
240
30
45
50
55
55
50
50
710
610
470
380
310
230
190
25
35
40
45
45
40
35
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
a 2 4 flute end mill for general use on mild steel through to difficult-to-cut materials.
< 0.3DC
Depth of
cut
< 1.5DC
DC:Dia.
J399
VIOLET END MILLS
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
SQUARE
DC
Hardened Steel
( < 55HRC)
30
Type2
Type3
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DCON
(<30HRC)
( < 45HRC)
KHA S
DCON
VA4MC
DCON
HSS
APMX
DC < 20
0
+ 0.030
LF
DC>20
0
+ 0.040
J400
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VA4MCD0300
VA4MCD0400
VA4MCD0500
VA4MCD0600
VA4MCD0700
VA4MCD0800
VA4MCD0900
VA4MCD1000
VA4MCD1100
VA4MCD1200
VA4MCD1300
VA4MCD1400
VA4MCD1500
VA4MCD1600
VA4MCD1700
VA4MCD1800
VA4MCD1900
VA4MCD2000
VA4MCD2200
VA4MCD2400
VA4MCD2500
VA4MCD2800
VA4MCD3000
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
24
25
28
30
10
12
15
15
20
20
25
25
30
30
35
35
40
40
40
40
45
45
45
50
50
55
55
50
60
60
60
65
65
75
75
85
85
90
95
100
100
100
100
115
115
115
120
120
125
125
6
8
8
8
10
10
10
10
12
12
12
16
16
16
16
16
20
20
20
25
25
25
25
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
1
2
3
1
1
2
3
3
1
2
3
1
2
3
3
HSS

y Side milling
Work
material

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2

(35 40HRC)
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
3
4
5
6
8
10
12
16
20
25
30
5400
4300
3600
3200
2400
1900
1600
1200
950
760
640
270
320
340
350
380
420
380
340
290
240
210
4000
3200
2700
2400
1800
1400
1200
900
720
570
480
200
240
250
260
290
300
290
260
220
180
160
2700
2100
1800
1600
1200
950
800
600
480
380
320
140
160
170
180
190
210
190
170
140
120
100
2200
1800
1500
1300
1000
800
660
500
400
320
270
100
120
130
140
145
160
145
130
110
100
80
< 0.2DC
Depth of
cut
< 1.5DC
DC:Dia.
SOLID END MILLS
J401
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
SQUARE
DC
Hardened Steel
( < 55HRC)
BALL
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DCON
(<30HRC)
( < 45HRC)
30
KHA S
DCON
S4MD
DCON
HSS
APMX
LF
DC < 20
0
+ 0.020
DC>20
0
+ 0.030
for high speed milling and cutting of high hardness difficult-to-cut materials.
J402
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
a 4 flute end mill with high grade powder metallurgy HSS (KHA Super) substrate
S4MDD0250
S4MDD0300
S4MDD0350
S4MDD0400
S4MDD0450
S4MDD0500
S4MDD0550
S4MDD0600
S4MDD0650
S4MDD0700
S4MDD0750
S4MDD0800
S4MDD0850
S4MDD0900
S4MDD0950
S4MDD1000S10
S4MDD1000S12
S4MDD1100
S4MDD1200
S4MDD1300
S4MDD1400
S4MDD1500
S4MDD1600
S4MDD1700
S4MDD1800
S4MDD1900
S4MDD2000
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
10
11
12
13
14
15
16
17
18
19
20
10
10
12
12
15
15
15
15
20
20
20
20
25
25
25
25
25
30
30
35
35
40
40
40
40
45
45
50
50
60
60
60
60
60
60
65
65
65
65
75
75
75
75
75
85
85
90
95
100
100
100
100
115
115
6
6
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
12
16
16
16
16
16
20
20
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
3
1
1
2
3
3
1
2
HSS

y Side milling
Work
material
3900
3100
2700
2400
1900
1500
1250
940
(S4MD)
Depth of
cut

(35 40HRC)
AISI 304, AISI 316
AISI No 35 B
Aluminium alloy
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
240
270
300
320
350
380
350
300
3100
2400
2000
1700
1300
1100
900
680
175
190
240
240
260
290
260
230
2400
1850
1500
1300
990
800
670
500
150
150
160
175
175
175
160
135
1900
1450
1200
1000
800
650
540
400
95
95
110
135
135
145
135
110
3400
2700
2200
1900
1450
1200
990
760
260
300
320
350
380
430
380
320
8200
6500
5400
4800
3800
3200
2700
2000
660
850
980
1100
1250
1200
1100
960
Dia.
Revolution
DC (mm)
(min-1)
3
4
5
6
8
10
12
16

Carbon steel,
(30 35HRC)
AISI 1055, AISI P20
AISI H13
Structural steel,
Carbon steel
< 0.2DC
< 1.5DC
DC:Dia.
SOLID END MILLS
J403
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
SQUARE
DC
Hardened Steel
( < 55HRC)
30
BALL
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DCON
(<30HRC)
( < 45HRC)
CO HSS
DCON
G4MC
DCON
HSS
APMX
LF
DC < 20
0
+ 0.030
DC>20
0
+ 0.040
a 4 flute end mill for high speed continuous cutting.
J404
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
G4MCD0300
G4MCD0350
G4MCD0400
G4MCD0450
G4MCD0500
G4MCD0550
G4MCD0600
G4MCD0650
G4MCD0700
G4MCD0750
G4MCD0800
G4MCD0850
G4MCD0900
G4MCD0950
G4MCD1000
G4MCD1100
G4MCD1200
G4MCD1300
G4MCD1400
G4MCD1500
G4MCD1600
G4MCD1700
G4MCD1800
G4MCD1900
G4MCD2000
G4MCD2100
G4MCD2200
G4MCD2300
G4MCD2400
G4MCD2500
G4MCD2600
G4MCD2700
G4MCD2800
G4MCD2900
G4MCD3000
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
10
12
12
15
15
15
15
20
20
20
20
25
25
25
25
30
30
35
35
40
40
40
40
45
45
45
45
50
50
50
50
55
55
55
55
50
60
60
60
60
60
60
65
65
65
65
75
75
75
75
85
85
90
95
100
100
100
100
115
115
115
115
120
120
120
120
125
125
125
125
6
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
16
16
16
16
16
20
20
20
20
25
25
25
25
25
25
25
25
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
3
1
1
2
3
3
1
2
3
3
1
1
2
3
3
3
3
3
HSS

y Side milling
Work
material
2800
2150
1900
1700
1300
1000
860
650
520
420
350
250
190
(G4MC)
Depth of
cut
Austenitic
stainless steel
Cast iron
AISI 304, AISI 316
AISI No 35 B
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
145
160
185
190
210
230
210
180
150
135
130
95
80
2200
1700
1450
1200
960
770
640
480
380
300
250
180
140
105
110
145
145
150
175
150
145
110
95
90
55
55
1700
1300
1100
940
700
560
470
360
290
230
190
140
110
90
90
95
105
105
105
95
90
70
65
55
40
40
1300
1000
850
730
560
460
370
280
230
180
145
110
85
55
55
65
80
80
90
80
65
55
50
40
35
30
2400
1900
1600
1300
1000
840
700
530
420
340
290
220
170
150
175
190
210
220
260
220
190
160
145
135
105
90
5800
4600
3800
3400
2600
2200
1900
1450
1150
910
770
580
460
380
500
580
640
740
690
670
560
480
420
380
300
260
Dia.
Revolution
DC (mm)
(min-1)
3
4
5
6
8
10
12
16
20
25
30
40
50

Carbon steel,
(30 35HRC)
AISI 1055, AISI P20
AISI H13
Structural steel,
Carbon steel
Aluminium alloy
< 0.2DC
< 1.5DC
DC:Dia.
SOLID END MILLS
J405
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
SQUARE
DC
Hardened Steel
( < 55HRC)
Type2
Type3
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DCON
(<30HRC)
( < 45HRC)
30
CO HSS
DCON
4MC
DCON
HSS
APMX
DC < 20
0
+ 0.020
LF
DC>20
0
+ 0.030
J406
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
4MCD0250
4MCD0300
4MCD0350
4MCD0400
4MCD0450
4MCD0500
4MCD0550
4MCD0600
4MCD0650
4MCD0700
4MCD0750
4MCD0800
4MCD0850
4MCD0900
4MCD0950
4MCD1000
4MCD1100
4MCD1200
4MCD1300
4MCD1400
4MCD1500
4MCD1600
4MCD1700
4MCD1800
4MCD1900
4MCD2000
4MCD2100
4MCD2200
4MCD2300
4MCD2400
4MCD2500
4MCD2600
4MCD2700
4MCD2800
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
7.5
8
8.5
9
9.5
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
10
10
12
12
15
15
15
15
20
20
20
20
25
25
25
25
30
30
35
35
40
40
40
40
45
45
45
45
50
50
50
50
55
55
50
50
60
60
60
60
60
60
65
65
65
65
75
75
75
75
85
85
90
95
100
100
100
100
115
115
115
115
120
120
120
120
125
125
6
6
8
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
16
16
16
16
16
20
20
20
20
25
25
25
25
25
25
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
3
1
1
2
3
3
1
2
3
3
1
1
2
3
3
3
HSS
APMX
LF
DCON
Stock
4MCD2900
4MCD3000
4MCD3100
4MCD3200
4MCD3300
4MCD3400
4MCD3500
4MCD3600
4MCD3700
4MCD3800
4MCD3900
4MCD4000
29
30
31
32
33
34
35
36
37
38
39
40
55
55
60
60
60
60
60
65
65
65
65
65
125
125
145
145
145
145
145
150
150
150
150
150
25
25
25
32
32
32
32
32
32
32
32
32
4
4
4
4
4
4
4
4
4
4
4
4
Type
3
3
3
2
3
3
3
3
3
3
3
3
a
a
a
a
a
a
a
a
a
a
RADIUS

y Side milling
Cast iron
Aluminium alloy
AISI 304, AISI 316
AISI No 35 B
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
105
120
135
140
155
170
155
135
110
100
90
70
1800
1400
1200
1000
800
640
530
400
320
250
210
150
80
85
105
105
110
120
110
105
85
70
65
40
1400
1100
900
780
580
470
390
300
240
190
160
120
65
65
70
80
80
80
70
65
55
45
40
30
1100
850
710
610
470
380
310
230
190
150
120
90
45
45
50
55
55
65
55
50
45
35
30
25
2000
1600
1300
1100
850
700
580
440
350
285
240
180
110
125
140
155
160
180
160
140
120
105
100
80
4800
3800
3200
2800
2200
1800
1600
1200
960
760
640
480
280
370
420
460
530
500
490
410
350
310
280
220
TAPER
2300
1800
1600
1400
1100
860
720
540
430
350
290
210
(4MC)
Depth of
cut
Austenitic
stainless steel
Dia.
Revolution
DC (mm)
(min-1)
3
4
5
6
8
10
12
16
20
25
30
40

Carbon steel,
(30 35HRC)
AISI 1055, AISI P20
AISI H13
Structural steel,
Carbon steel
SOLID END MILLS
Work
material
SQUARE
DC
BALL
Order Number
No. of
Flutes
Unit : mm
< 0.2DC
< 1.5DC
DC:Dia.
J407
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
SQUARE
DC
Hardened Steel
( < 55HRC)
APMX
DCON
(<30HRC)
( < 45HRC)
30
KHA S
Type1
DCON
S4JC
Type2
DCON
HSS
Type3
DC
LF
APMX
BALL
DC
LF
APMX
LF
DC < 20
0
+ 0.020
DC>20
0
+ 0.030
J408
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
S4JCD0300
S4JCD0400
S4JCD0500
S4JCD0600
S4JCD0700
S4JCD0800
S4JCD0900
S4JCD1000
S4JCD1100
S4JCD1200
S4JCD1300
S4JCD1400
S4JCD1500
S4JCD1600
S4JCD1700
S4JCD1800
S4JCD1900
S4JCD2000
S4JCD2500
S4JCD3000
S4JCD3500
S4JCD4000
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
25
30
35
40
12
15
20
20
25
25
35
35
45
45
45
55
55
55
55
55
65
65
75
75
85
95
60
65
75
75
80
80
90
90
110
110
110
125
125
125
125
125
145
145
165
165
190
200
6
8
8
8
10
10
10
10
12
12
12
16
16
16
16
16
20
20
25
25
32
32
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
1
2
3
1
1
2
3
3
1
2
2
3
3
3
HSS

y Side milling
Work
material
3900
3100
2700
2400
1900
1500
1250
940
(S4MD)
Depth of
cut

(35 40HRC)
AISI 304, AISI 316
AISI No 35 B
Aluminium alloy
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
240
270
300
320
350
380
350
300
3100
2400
2000
1700
1300
1100
900
680
175
190
240
240
260
290
260
230
2400
1850
1500
1300
990
800
670
500
150
150
160
175
175
175
160
135
1900
1450
1200
1000
800
650
540
400
95
95
110
135
135
145
135
110
3400
2700
2200
1900
1450
1200
990
760
260
300
320
350
380
430
380
320
8200
6500
5400
4800
3800
3200
2700
2000
660
850
980
1100
1250
1200
1100
960
Dia.
Revolution
DC (mm)
(min-1)
3
4
5
6
8
10
12
16

Carbon steel,
(30 35HRC)
AISI 1055, AISI P20
AISI H13
Structural steel,
Carbon steel
< 0.2DC
< 1.5DC
DC:Dia.
SOLID END MILLS
1) Use the milling by reducing the feedrate in the table shown above by 20 30% in accordance with the cutting type.
J409
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
SQUARE
DC
Hardened Steel
( < 55HRC)
30
APMX
Type1
Type2
Type3
DC
LF
APMX
LF
DC
BALL
DCON
(<30HRC)
( < 45HRC)
CO HSS
DCON
G4LC
DCON
HSS
APMX
LF
DC < 20
0
+ 0.030
DC>20
0
+ 0.040
a 4 flute end mill with long flute for deep cutting applications.
J410
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
G4LCD0300
G4LCD0400
G4LCD0500
G4LCD0600
G4LCD0700
G4LCD0800
G4LCD0900
G4LCD1000
G4LCD1100
G4LCD1200
G4LCD1300
G4LCD1400
G4LCD1500
G4LCD1600
G4LCD1700
G4LCD1800
G4LCD1900
G4LCD2000
G4LCD2100
G4LCD2200
G4LCD2300
G4LCD2400
G4LCD2500
G4LCD2600
G4LCD2700
G4LCD2800
G4LCD2900
G4LCD3000
G4LCD3100
G4LCD3200
G4LCD3300
G4LCD3400
G4LCD3500
G4LCD3600
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
15
20
25
25
35
35
45
45
55
55
55
55
65
65
65
65
75
75
75
75
90
90
90
90
90
90
90
90
95
95
95
100
100
105
55
55
60
60
75
75
90
90
105
105
105
110
120
120
120
120
140
140
140
140
160
160
160
160
160
160
160
160
180
180
180
185
185
190
6
8
8
8
10
10
10
10
12
12
12
16
16
16
16
16
20
20
20
20
25
25
25
25
25
25
25
25
25
32
32
32
32
32
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
1
2
3
1
1
2
3
3
1
2
3
3
1
1
2
3
3
3
3
3
3
2
3
3
3
3
HSS
DC
APMX
LF
DCON
Stock
G4LCD3700
G4LCD3800
G4LCD3900
G4LCD4000
37
38
39
40
105
105
110
110
190
190
195
195
32
32
32
32
4
4
4
4
Type
3
3
3
3
a
a
a
SQUARE
Order Number
No. of
Flutes
Unit : mm
BALL

y Side milling
Cast iron
Aluminium alloy
AISI 304, AISI 316
AISI No 35 B
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
145
160
185
190
210
230
210
180
150
135
130
95
80
2200
1700
1450
1200
960
770
640
480
380
300
250
180
140
105
110
145
145
150
175
150
145
110
95
90
55
55
1700
1300
1100
940
700
560
470
360
290
230
190
140
110
90
90
95
105
105
105
95
90
70
65
55
40
40
1300
1000
850
730
560
460
370
280
230
180
145
110
85
55
55
65
80
80
90
80
65
55
50
40
35
30
2400
1900
1600
1300
1000
840
700
530
420
340
290
220
170
150
175
190
210
220
260
220
190
160
145
135
105
90
5800
4600
3800
3400
2600
2200
1900
1450
1150
910
770
580
460
380
500
580
640
740
690
670
560
480
420
380
300
260
< 0.2DC
< 1.5DC
DC:Dia.
RADIUS
2800
2150
1900
1700
1300
1000
860
650
520
420
350
250
190
(G4MC)
Depth of
cut
Austenitic
stainless steel
Dia.
Revolution
DC (mm)
(min-1)
3
4
5
6
8
10
12
16
20
25
30
40
50

Carbon steel,
(30 35HRC)
AISI 1055, AISI P20
AISI H13
TAPER
Structural steel,
Carbon steel
SOLID END MILLS
Work
material
1) Use the milling by reducing the revolution in the table shown above by 20 30% and the feedrate 40 50% to match the cutting type.
J411
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
SQUARE
DC
Hardened Steel
( < 55HRC)
Type1
Type2
Type3
LF
DC
APMX
DCON
(<30HRC)
( < 45HRC)
30
CO HSS
DCON
4LC
DCON
HSS
APMX
BALL
DC
LF
APMX
LF
DC < 20
0
+ 0.020
DC>20
0
+ 0.030
a 4 flute end mill with long flute for deep cutting applications.
J412
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
4LCD0300
4LCD0400
4LCD0500
4LCD0600
4LCD0700
4LCD0800
4LCD0900
4LCD1000
4LCD1100
4LCD1200
4LCD1300
4LCD1400
4LCD1500
4LCD1600
4LCD1700
4LCD1800
4LCD1900
4LCD2000
4LCD2100
4LCD2200
4LCD2300
4LCD2400
4LCD2500
4LCD2600
4LCD2700
4LCD2800
4LCD2900
4LCD3000
4LCD3100
4LCD3200
4LCD3300
4LCD3400
4LCD3500
4LCD3600
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
15
20
25
25
35
35
45
45
55
55
55
55
65
65
65
65
75
75
75
75
90
90
90
90
90
90
90
90
95
95
95
100
100
105
55
55
60
60
75
75
90
90
105
105
105
110
120
120
120
120
140
140
140
140
160
160
160
160
160
160
160
160
180
180
180
185
185
190
6
8
8
8
10
10
10
10
12
12
12
16
16
16
16
16
20
20
20
20
25
25
25
25
25
25
25
25
25
32
32
32
32
32
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
1
1
1
1
1
1
2
1
2
3
1
1
2
3
3
1
2
3
3
1
1
2
3
3
3
3
3
3
2
3
3
3
3
HSS
DC
APMX
LF
DCON
Stock
4LCD3700
4LCD3800
4LCD3900
4LCD4000
37
38
39
40
105
105
110
110
190
190
195
195
32
32
32
32
4
4
4
4
Type
3
3
3
3
a
a
a
SQUARE
Order Number
No. of
Flutes
Unit : mm
BALL

y Side milling
Cast iron
2300
1800
1600
1400
1100
860
720
540
430
350
290
210
Aluminium alloy
AISI 304, AISI 316
AISI No 35 B
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
105
120
135
140
155
170
155
135
110
100
90
70
1800
1400
1200
1000
800
640
530
400
320
250
210
150
80
85
105
105
110
120
110
105
85
70
65
40
1400
1100
900
780
580
470
390
300
240
190
160
120
65
65
70
80
80
80
70
65
55
45
40
30
1100
850
710
610
470
380
310
230
190
150
120
90
45
45
50
55
55
65
55
50
45
35
30
25
2000
1600
1300
1100
850
700
580
440
350
285
240
180
110
125
140
155
160
180
160
140
120
105
100
80
4800
3800
3200
2800
2200
1800
1600
1200
960
760
640
480
280
370
420
460
530
500
490
410
350
310
280
220
< 0.2DC
Depth of
cut
< 1.5DC
DC:Dia.
RADIUS
Austenitic
stainless steel
Dia.
Revolution
DC (mm)
(min-1)
3
4
5
6
8
10
12
16
20
25
30
40

Carbon steel,
(30 35HRC)
AISI 1055, AISI P20
AISI H13
TAPER
Structural steel,
Carbon steel
SOLID END MILLS
Work
material
1) Use the milling by reducing the revolution in the table shown above by 20 30% and the feedrate 40 50% to match the cutting type.
J413
ROUGHING END MILLS
Hardened Steel
(>55HRC)
DC<22
Austenitic
Stainless Steel
Titanium Alloy,
24<DC<32
Copper Alloy
SQUARE
APMX
Type2
Type3
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DC>35
Aluminium Alloy
DC
Hardened Steel
( < 55HRC)
30
DCON
(<30HRC)
( < 45HRC)
CO HSS
DCON
GSFPR
Roughing end mill, Short cut length, 3 6 flute, Fine pitch form
DCON
HSS
LF
a 3 6 flute roughing end mill with good chip disposal properties for high feed milling.
J414
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
GSFPRD0500
GSFPRD0600
GSFPRD0700
GSFPRD0800
GSFPRD0900
GSFPRD1000
GSFPRD1200
GSFPRD1300
GSFPRD1400
GSFPRD1500
GSFPRD1600
GSFPRD1800
GSFPRD1900
GSFPRD2000
GSFPRD2200
GSFPRD2400
GSFPRD2500
GSFPRD2800
GSFPRD3000
GSFPRD3200
GSFPRD3500
GSFPRD4000
GSFPRD4500
GSFPRD5000
5
6
7
8
9
10
12
13
14
15
16
18
19
20
22
24
25
28
30
32
35
40
45
50
10
12
17
17
22
22
27
27
27
27
33
33
38
38
38
43
43
43
48
55
55
65
65
75
80
80
80
85
100
100
110
110
135
140
140
140
145
145
145
150
150
160
165
175
175
185
200
200
6
6
8
8
10
10
12
12
12
16
16
16
20
20
20
25
25
25
25
25
32
32
42
42
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
2
1
2
1
2
2
3
3
1
2
3
1
2
3
1
2
3
3
3
3
3
3
3
HSS

Work
material

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
25
30
40
50
1200 (900)
1150 (860)
960 (720)
770 (580)
640 (480)
480 (360)
380 (290)
300 (230)
250 (190)
160 (120)
120 (90)
50 (40)
60 (45)
80 (60)
110 (85)
110 (85)
110 (85)
115 (85)
110 (85)
100 (75)
70 (55)
60 (45)
900 (680)
860 (650)
720 (540)
580 (440)
480 (360)
360 (270)
290 (220)
230 (170)
190 (145)
120 (90)
90 (70)
35 (25)
50 (40)
60 (45)
85 (65)
85 (65)
85 (65)
85 (65)
80 (60)
80 (60)
55 (40)
50 (40)
730 (550)
680 (510)
600 (450)
460 (350)
380 (290)
290 (220)
230 (170)
180 (135)
160 (120)
95 (70)
70 (55)
30 (23)
35 (26)
50 (40)
60 (45)
65 (50)
65 (50)
65 (50)
60 (45)
60 (45)
40 (30)
35 (25)
610 (460)
580 (440)
480 (360)
380 (290)
320 (240)
240 (180)
190 (145)
160 (120)
130 (100)
85 (65)
60 (45)
25 (20)
30 (23)
35 (26)
50 (40)
55 (40)
55 (40)
55 (40)
55 (40)
55 (40)
35 (26)
30 (23)
< 0.5DC
Depth of
cut
< 1.5DC
DC
< 1DC
(MAX. 30mm)
DC:Dia.
1) Supply cutting fluid sufficiently during cutting.

2) When the diameter exceeds 30 and the metal removal is less than the quantity shown in the table, the revolution and feed rate may be
increased by 10 40%.
SOLID END MILLS
( ) : Indicates standard revolution and feedrates for slotting
J415
VIOLET END MILLS
Hardened Steel
(>55HRC)
DC<24
Austenitic
Stainless Steel
Titanium Alloy,
25<DC<32
Copper Alloy
SQUARE
APMX
Type2
Type3
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DC>35
Aluminium Alloy
DC
Hardened Steel
( < 55HRC)
30
DCON
(<30HRC)
( < 45HRC)
KHA S
DCON
VASFPR
Roughing end mill, Short cut length, 4 6 flute, Fine pitch form
DCON
HSS
LF
a Roughing 4 6 flute end mill with high grade HSS substrate and Violet coating for general use.
J416
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VASFPRD0500
VASFPRD0600
VASFPRD0700
VASFPRD0800
VASFPRD0900
VASFPRD1000
VASFPRD1200
VASFPRD1400
VASFPRD1500
VASFPRD1600
VASFPRD1800
VASFPRD2000
VASFPRD2200
VASFPRD2400
VASFPRD2500
VASFPRD2800
VASFPRD3000
VASFPRD3200
VASFPRD3500
VASFPRD4000
VASFPRD4500
VASFPRD5000
5
6
7
8
9
10
12
14
15
16
18
20
22
24
25
28
30
32
35
40
45
50
10
12
17
17
22
22
27
27
27
33
33
38
38
43
43
43
48
55
55
65
65
75
80
80
80
85
100
100
110
110
125
125
125
145
145
150
150
160
165
175
175
185
200
200
6
6
8
8
10
10
12
12
16
16
16
20
20
25
25
25
25
25
32
32
42
42
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
2
1
2
1
2
2
3
1
2
3
2
3
1
2
3
3
3
3
3
3
3
HSS

y Side milling
Work
material

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2

(35 40HRC)
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
25
30
40
50
2800
2600
2200
1750
1450
1100
880
700
580
350
250
140
180
230
330
330
330
340
330
300
210
170
2200
2000
1700
1350
1100
850
680
540
450
270
190
120
140
180
250
260
260
260
250
230
170
130
1500
1400
1200
950
800
600
480
380
320
190
130
80
90
130
160
180
180
180
170
170
120
90
1300
1200
990
800
660
500
400
320
270
160
110
70
80
100
130
140
140
140
140
140
100
75
< 0.5DC
Depth of
cut
< 1.5DC
DC:Dia.
y Slotting
Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2

(35 40HRC)
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
25
30
40
50
2100
2000
1600
1300
1050
800
640
510
420
280
190
100
130
160
220
230
230
230
200
190
140
110
1650
1550
1300
1000
850
640
510
410
320
210
150
80
100
130
175
190
190
180
160
140
110
90
1150
1050
920
730
610
460
370
290
210
140
95
50
60
90
110
130
130
130
110
90
70
55
960
900
760
610
500
380
300
240
180
120
85
35
45
60
80
85
85
85
80
75
60
45
SOLID END MILLS
Work
material
DC
Depth of
cut
< 1DC
(MAX. 30mm)
DC:Dia.
1)
2)
3)
4)
Supply cutting fluid sufficiently during cutting. For dry-cutting, decrease the revolution and feed rate proportionately by 20 50%.
For smaller depths and widths of cut, the revolution may be increased by 10 20% and the feed rate by 10 40%.
J417
VIOLET END MILLS
Hardened Steel
(>55HRC)
30
DC<20
Austenitic
Stainless Steel
Titanium Alloy,
22<DC<28
Copper Alloy
SQUARE
BALL
APMX
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DC>30
Aluminium Alloy
DC
Hardened Steel
( < 55HRC)
DCON
(<30HRC)
( < 45HRC)
KHA S
DCON
VAMFPR
Roughing end mill, Medium cut length, 4 6 flute, Fine pitch form
DCON
HSS
LF
a 4 6 flute end mill with medium cut length.
J418
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VAMFPRD0500
VAMFPRD0600
VAMFPRD0700
VAMFPRD0800
VAMFPRD0900
VAMFPRD1000
VAMFPRD1200
VAMFPRD1400
VAMFPRD1500
VAMFPRD1600
VAMFPRD1800
VAMFPRD2000
VAMFPRD2200
VAMFPRD2400
VAMFPRD2500
VAMFPRD2800
VAMFPRD3000
VAMFPRD3200
VAMFPRD3500
VAMFPRD4000
VAMFPRD4500
VAMFPRD5000
5
6
7
8
9
10
12
14
15
16
18
20
22
24
25
28
30
32
35
40
45
50
15
17
22
28
28
34
40
40
40
48
48
57
57
68
68
68
68
80
80
94
94
113
80
80
80
85
95
100
110
110
120
125
125
145
145
150
150
160
165
175
175
185
200
200
6
6
8
8
10
10
12
12
16
16
16
20
20
25
25
25
25
32
32
32
42
42
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
2
1
2
1
2
2
3
1
2
3
2
3
1
2
3
3
2
3
3
3
3
HSS

y Side milling
Work
material

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2

(35 40HRC)
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
25
30
40
50
2600
2500
2000
1650
1400
1000
830
660
550
330
240
90
100
170
220
260
290
300
290
270
180
160
2000
1900
1600
1300
1000
800
640
510
420
250
180
70
90
130
170
210
230
230
220
210
140
120
1400
1300
1100
900
750
560
450
360
300
180
120
50
50
90
100
140
160
160
160
140
100
80
1200
1100
930
750
620
470
380
300
250
150
100
40
50
80
90
120
130
130
130
130
90
70
< 0.25DC
Depth of
cut
< 2.5DC
< 2DC
(MAX. 10mm)
(DC < & 25)

(DC > & 25)
DC:Dia.
SOLID END MILLS
1) Supply cutting fluid sufficiently during cutting. For dry-cutting, decrease the revolution and feed rate proportionately by 20 50%.
increased proportionately by 10 40%.
J419
VIOLET END MILLS

DC<15
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
16<DC<26
SQUARE
Copper Alloy
Aluminium Alloy
APMX
Type2
Type3
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DC>35
28<DC<32
DC
Hardened Steel
( < 55HRC)
30
DCON
(<30HRC)
( < 45HRC)
KHA S
DCON
VAMR
Roughing end mill, Medium cut length, 4 6 flute
DCON
HSS
LF
a Roughing 4 6 flute end mill with high grade HSS substrate and Violet coating for general use.
J420
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VAMRD0500
VAMRD0600
VAMRD0700
VAMRD0800
VAMRD0900
VAMRD1000
VAMRD1100
VAMRD1200
VAMRD1300
VAMRD1400
VAMRD1500
VAMRD1600
VAMRD1700
VAMRD1800
VAMRD1900
VAMRD2000
VAMRD2200
VAMRD2400
VAMRD2500
VAMRD2600
VAMRD2800
VAMRD3000
VAMRD3200
VAMRD3500
VAMRD4000
VAMRD4500
VAMRD5000
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
24
25
26
28
30
32
35
40
45
50
15
15
20
20
25
25
30
30
35
35
40
40
40
40
45
45
45
50
50
50
55
55
60
60
65
70
70
60
60
70
70
80
80
110
110
115
135
140
140
140
140
145
145
145
150
150
150
160
165
175
175
185
200
200
6
6
8
8
10
10
12
12
12
16
16
16
16
16
20
20
20
25
25
25
25
25
32
32
32
42
42
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
2
1
2
1
2
1
2
3
1
1
2
3
3
1
2
3
1
2
3
3
3
2
3
3
3
3
HSS

y Side milling
Work
material

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2

(35 40HRC)
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
25
30
40
50
2400
2200
1800
1500
1250
930
750
600
490
300
210
120
155
200
250
270
270
290
270
250
180
140
1800
1700
1400
1100
960
720
580
460
380
230
160
90
120
140
200
220
220
220
210
200
140
110
1200
1100
950
810
680
510
410
320
270
160
110
60
70
100
125
160
160
160
140
140
105
80
1000
930
780
680
560
430
340
270
230
140
90
50
65
85
100
120
120
120
120
120
90
65
< 0.5DC
Depth of
cut
< 1.5DC
DC:Dia.
y Slotting
Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
25
30
40
50
1800
1700
1300
1100
900
680
550
440
350
240
260
85
110
140
170
190
190
195
170
160
120
90
1350
1300
1050
810
740
540
440
350
270
180
125
60
85
100
140
160
160
150
135
120
90
75
Revolution
(min-1)
920
830
730
620
520
390
320
240
180
120
80
Feed rate
(mm/min)
40
45
70
85
115
115
115
90
75
60
50

(35 40HRC)
AISI 304, AISI 316
Revolution
(min-1)
740
700
600
520
420
330
260
200
155
105
70
Feed rate
(mm/min)
25
35
50
60
75
75
75
70
65
55
40
SOLID END MILLS
Work
material
DC
Depth of
cut
< 1DC
(MAX. 30mm)
DC:Dia.
J421
VIOLET END MILLS

DC<15
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
16<DC<25
Copper Alloy
DC=30
SQUARE
BALL
APMX
Type2
Type3
LF
DC
APMX
Type1
LF
DC
APMX
DC>35
Aluminium Alloy
DC
Hardened Steel
( < 55HRC)
30
DCON
(<30HRC)
( < 45HRC)
KHA S
DCON
VAJR
Roughing end mill, Semi long cut length, 4 6 flute
DCON
HSS
LF
a 4 6 flute end mill with longer cut length than standard.
J422
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VAJRD1000
VAJRD1200
VAJRD1400
VAJRD1500
VAJRD1600
VAJRD1800
VAJRD2000
VAJRD2500
VAJRD3000S25
VAJRD3000S32
VAJRD3500
VAJRD4000
VAJRD4500
VAJRD5000
10
12
14
15
16
18
20
25
30
30
35
40
45
50
35
45
45
55
55
55
65
75
75
75
85
85
105
105
90
125
145
155
155
155
165
175
185
185
200
205
235
235
10
12
16
16
16
16
20
25
25
32
32
42
42
42
4
4
4
4
4
4
4
4
5
5
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
2
1
1
2
3
2
2
3
1
3
1
3
3
HSS

y Side milling
Carbon steel

(20 30HRC)

SCM, AISI H13, AISI D2

(35 40HRC)
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
10
12
16
20
25
30
40
50
1400
1200
870
700
560
460
280
200
170
170
170
170
170
155
105
90
1100
900
680
540
430
360
220
150
130
130
130
130
120
120
90
65
760
640
480
380
300
260
150
100
80
90
90
90
90
80
65
50
640
530
400
320
260
220
130
90
65
80
80
80
80
65
65
40
< 0.25DC
Depth of
cut
< 2.5DC
< 2DC
(MAX. 10mm)
(DC < & 30)

(DC > & 30)
DC:Dia.
SOLID END MILLS
Work
material
J423
VIOLET END MILLS
VALR
Roughing end mill, Long cut length, 4 6 flute
(<30HRC)
( < 45HRC)
30
10<DC<25
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
28<DC<32
Copper Alloy
DC>35
Aluminium Alloy
SQUARE
DC
Hardened Steel
( < 55HRC)
KHA S
Type1
DCON
HSS
APMX
DC
LF
DCON
Type2
APMX
Type3
DCON
DC
BALL
LF
APMX
LF
a 4 6 flute end mill with long cut length.
J424
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
VALRD1000
VALRD1200
VALRD1400
VALRD1500
VALRD1600
VALRD1800
VALRD2000
VALRD2200
VALRD2400
VALRD2500
VALRD2800
VALRD3000
VALRD3200
VALRD3500
VALRD4000
VALRD4500
VALRD5000
10
12
14
15
16
18
20
22
24
25
28
30
32
35
40
45
50
45
50
55
65
65
65
75
75
85
90
90
90
95
100
110
120
120
110
130
155
165
165
165
175
175
185
190
190
200
210
215
230
250
250
10
12
16
16
16
16
20
20
25
25
25
25
32
32
32
42
42
4
4
4
4
4
4
4
4
4
4
5
5
5
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
2
1
1
2
3
2
3
1
2
3
3
2
3
3
3
3
HSS

y Side milling
Work
material

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
10
12
16
20
25
30
40
50
1000
850
700
560
450
370
260
180
75
90
100
100
100
100
80
65
700
630
540
430
340
290
200
140
55
70
80
80
75
75
60
50
Revolution
(min-1)

(35 40HRC)
AISI 304, AISI 316
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
40
50
55
55
55
50
45
35
400
370
320
260
210
170
120
80
30
40
45
50
50
45
40
30
480
440
380
300
240
200
135
90
< 0.1DC
Depth of
cut
(DC < & 30)

(DC> & 30)
(MAX. 100mm)
< 3DC
< 2.5DC
DC:Dia.
SOLID END MILLS
J425
ROUGHING END MILLS

DC<25
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
SQUARE
Copper Alloy
Aluminium Alloy
Type2
Type3
LF
DC
BALL
APMX
Type1
LF
DC
APMX
DC>35
28<DC<32
DC
Hardened Steel
( < 55HRC)
DCON
(<30HRC)
( < 45HRC)
30
CO HSS
DCON
SR
DCON
HSS
APMX
LF
a 4 6 flute roughing end mill with full radius cutting edge profile for heavy cutting.
J426
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
SRD1000
SRD1200
SRD1300
SRD1400
SRD1500
SRD1600
SRD1800
SRD1900
SRD2000
SRD2200
SRD2500
SRD2800
SRD3000
SRD3200
SRD3500
SRD4000
10
12
13
14
15
16
18
19
20
22
25
28
30
32
35
40
22
27
27
27
27
33
33
38
38
38
43
43
48
55
55
65
75
85
85
90
95
100
100
110
110
110
125
125
130
145
145
165
10
12
12
16
16
16
16
20
20
20
25
25
25
32
32
32
4
4
4
4
4
4
4
4
4
4
4
5
5
5
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
2
3
1
1
2
3
1
2
3
2
3
3
2
3
3
HSS

Work
material

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
25
30
40
50
1000 (750)
960 (720)
800 (600)
640 (480)
530 (400)
400 (300)
320 (240)
250 (190)
210 (160)
135 (100)
100 (75)
40 (30)
50 (40)
65 (50)
90 (70)
90 (70)
90 (70)
95 (70)
90 (70)
85 (65)
60 (45)
50 (40)
760 (570)
720 (540)
600 (450)
480 (360)
400 (300)
300 (230)
240 (180)
190 (140)
160 (120)
100 (75)
75 (55)
30 (25)
40 (30)
50 (40)
70 (55)
70 (55)
70 (55)
70 (55)
65 (50)
65 (50)
45 (40)
40 (30)
610 (460)
570 (430)
500 (380)
380 (290)
320 (240)
240 (180)
190 (140)
150 (110)
130 (100)
80 (60)
60 (45)
25 (20)
30 (25)
40 (30)
50 (40)
55 (40)
55 (40)
55 (40)
50 (40)
50 (40)
35 (26)
30 (23)
510 (380)
480 (360)
400 (300)
320 (240)
270 (200)
200 (150)
160 (120)
130 (100)
110 (85)
70 (55)
50 (40)
20 (15)
25 (20)
30 (25)
40 (30)
45 (35)
45 (35)
45 (35)
45 (35)
45 (35)
30 (25)
25 (20)
< 0.5DC
Depth of
cut
< 1.5DC
DC
< 1DC
(MAX. 30mm)
DC:Dia.

SOLID END MILLS
J427
ROUGHING END MILLS
GMR
(<30HRC)
( < 45HRC)
30
DC<15
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
16<DC<26
SQUARE
DC>35
28<DC<32
Copper Alloy
Aluminium Alloy
DC
Hardened Steel
( < 55HRC)
CO HSS
DCON
HSS
LF
DC
APMX
Type1
LF
DC
BALL
APMX
DCON
Type2
DCON
Type3
APMX
LF
rough milling of steels through to difficult-to-cut materials.
J428
Order Number
DC
APMX
LF
DCON
Stock
Unit : mm
No. of
Flutes
SOLID END MILLS
TAPER
RADIUS
a 4 6 flute roughing end mill with TiN coating for general
GMRD0500
GMRD0600
GMRD0700
GMRD0800
GMRD0900
GMRD1000
GMRD1100
GMRD1200
GMRD1300
GMRD1400
GMRD1500
GMRD1600
GMRD1700
GMRD1800
GMRD1900
GMRD2000
GMRD2200
GMRD2400
GMRD2500
GMRD2600
GMRD2800
GMRD3000
GMRD3200
GMRD3500
GMRD4000
GMRD4500
GMRD5000
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
24
25
26
28
30
32
35
40
45
50
15
15
20
20
25
25
30
30
35
35
40
40
40
40
45
45
45
50
50
50
55
55
60
60
65
70
70
60
60
70
70
80
80
110
110
115
135
140
140
140
140
145
145
145
150
150
150
160
165
175
175
185
200
200
6
6
8
8
10
10
12
12
12
16
16
16
16
16
20
20
20
25
25
25
25
25
32
32
32
42
42
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
2
1
2
1
2
1
2
3
1
1
2
3
3
1
2
3
1
2
3
3
3
2
3
3
3
3
HSS

Work
material

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
25
30
40
50
1200 (900)
1150 (860)
960 (720)
770 (580)
640 (480)
480 (360)
380 (290)
300 (230)
250 (190)
160 (120)
120 (90)
50 (40)
60 (45)
80 (60)
110 (85)
110 (85)
110 (85)
115 (85)
110 (85)
100 (75)
70 (55)
60 (45)
900 (680)
860 (650)
720 (540)
580 (440)
480 (360)
360 (270)
290 (220)
230 (170)
190 (145)
120 (90)
90 (70)
35 (25)
50 (40)
60 (45)
85 (65)
85 (65)
85 (65)
85 (65)
80 (60)
80 (60)
55 (40)
50 (40)
730 (550)
680 (510)
600 (450)
460 (350)
380 (290)
290 (220)
230 (170)
180 (135)
160 (120)
95 (70)
70 (55)
30 (23)
35 (26)
50 (40)
60 (45)
65 (50)
65 (50)
65 (50)
60 (45)
60 (45)
40 (30)
35 (25)
610 (460)
580 (440)
480 (360)
380 (290)
320 (240)
240 (180)
190 (145)
160 (120)
130 (100)
85 (65)
60 (45)
25 (20)
30 (23)
35 (26)
50 (40)
55 (40)
55 (40)
55 (40)
55 (40)
55 (40)
35 (26)
30 (23)
< 0.5DC
Depth of
cut
< 1.5DC
DC
< 1DC
(MAX. 30mm)
DC:Dia.

SOLID END MILLS
J429
ROUGHING END MILLS
MR
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
DC<15
Austenitic
Stainless Steel
Titanium Alloy,
16<DC<26
28<DC<32
Copper Alloy
SQUARE
DC>35
Aluminium Alloy
DC
Hardened Steel
( < 55HRC)
30
CO HSS
DCON
HSS
APMX
Type1
LF
LF
Type3
DCON
BALL
DC
APMX
DCON
DC
Type2
APMX
LF
J430
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
MRD0500
MRD0600
MRD0700
MRD0800
MRD0900
MRD1000
MRD1100
MRD1200
MRD1300
MRD1400
MRD1500
MRD1600
MRD1700
MRD1800
MRD1900
MRD2000
MRD2200
MRD2400
MRD2500
MRD2600
MRD2800
MRD3000S25
MRD3000S32
MRD3200
MRD3500
MRD4000S32
MRD4000S42
MRD4500
MRD5000
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
24
25
26
28
30
30
32
35
40
40
45
50
15
15
20
20
25
25
30
30
35
35
40
40
40
40
45
45
45
50
50
50
55
55
55
60
60
65
65
70
70
60
60
70
70
80
80
110
110
115
135
140
140
140
140
145
145
145
150
150
150
160
165
165
175
175
185
185
200
200
6
6
8
8
10
10
12
12
12
16
16
16
16
16
20
20
20
25
25
25
25
25
32
32
32
32
42
42
42
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
1
2
1
2
1
2
1
2
3
1
1
2
3
3
1
2
3
1
2
3
3
3
1
2
3
3
1
3
3
Titanium Alloy,
16<DC<25
Copper Alloy
Aluminium Alloy
Type2
LF
DC
APMX
Type1
LF
DC
APMX
DC>35
28<DC<32
SQUARE
DC<15
Austenitic
Stainless Steel
Type3
DCON
APMX
LF
BALL
Hardened Steel
(>55HRC)
DC
Hardened Steel
( < 55HRC)
HSS
DCON
(<30HRC)
( < 45HRC)
30
CO HSS
DCON
JR
Roughing end mill, Semi long cut length, 4 6 flute
APMX
LF
DCON
Stock
JRD1000
JRD1200
JRD1400
JRD1500
JRD1600
JRD1800
JRD2000
JRD2200
JRD2400
JRD2500
JRD2800
JRD3000S25
JRD3000S32
JRD3200
JRD3500
JRD4000S32
JRD4000S42
JRD4500
JRD5000
10
12
14
15
16
18
20
22
24
25
28
30
30
32
35
40
40
45
50
35
45
45
55
55
55
65
65
65
75
75
75
75
75
85
85
85
105
105
90
125
145
155
155
155
165
165
165
175
180
185
185
190
200
205
205
235
235
10
12
16
16
16
16
20
20
25
25
25
25
32
32
32
32
42
42
42
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
2
1
1
2
3
2
3
1
2
3
3
1
2
3
3
1
3
3
TAPER
DC
SOLID END MILLS
Order Number
No. of
Flutes
Unit : mm
RADIUS
J431
ROUGHING END MILLS
LR
(<30HRC)
( < 45HRC)
DC<25
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
28<DC<32
Copper Alloy
DC>35
Aluminium Alloy
u
Type1
LF
DC
APMX
DCON
SQUARE
DC
Hardened Steel
( < 55HRC)
30
CO HSS
DCON
Type2
APMX
LF
BALL
DC
Type3
DCON
HSS
APMX
LF
a 4 6 flute end mill with longer cut length and overall length than standard.
J432
Order Number
DC
APMX
LF
DCON
No. of
Flutes
Stock
SOLID END MILLS
TAPER
RADIUS
Unit : mm
LRD1000
LRD1200
LRD1400
LRD1500
LRD1600
LRD1800
LRD2000
LRD2200
LRD2400
LRD2500
LRD2800
LRD3000S25
LRD3000S32
LRD3200
LRD3500
LRD4000S32
LRD4000S42
LRD4500
LRD5000
10
12
14
15
16
18
20
22
24
25
28
30
30
32
35
40
40
45
50
45
50
55
65
65
65
75
75
85
90
90
90
90
95
100
110
110
120
120
110
130
155
165
165
165
175
175
185
190
190
200
200
210
215
230
230
250
250
10
12
16
16
16
16
20
20
25
25
25
25
32
32
32
32
42
42
42
4
4
4
4
4
4
4
4
4
4
5
5
5
5
6
6
6
6
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type
2
2
1
1
2
3
2
3
1
2
3
3
1
2
3
3
1
3
3
MR
Roughing end mill, Medium cut length, 4 6 flute JR
1)
LR
HSS
2)

Carbon steel

(20 30HRC)

AISI 1055, AISI P20
AISI H13, AISI D2
AISI 304, AISI 316
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
Revolution
(min-1)
Feed rate
(mm/min)
5
6
8
10
12
16
20
25
30
40
50
1000 (750)
960 (720)
800 (600)
640 (480)
530 (400)
400 (300)
320 (240)
250 (190)
210 (160)
135 (100)
100 (75)
40 (30)
50 (40)
65 (50)
90 (70)
90 (70)
90 (70)
95 (70)
90 (70)
85 (65)
60 (45)
50 (40)
760 (570)
720 (540)
600 (450)
480 (360)
400 (300)
300 (230)
240 (180)
190 (140)
160 (120)
100 (75)
75 (55)
30 (25)
40 (30)
50 (40)
70 (55)
70 (55)
70 (55)
70 (55)
65 (50)
65 (50)
45 (40)
40 (30)
610 (460)
570 (430)
500 (380)
380 (290)
320 (240)
240 (180)
190 (140)
150 (110)
130 (100)
80 (60)
60 (45)
25 (20)
30 (25)
40 (30)
50 (40)
55 (40)
55 (40)
55 (40)
50 (40)
50 (40)
35 (26)
30 (23)
510 (380)
480 (360)
400 (300)
320 (240)
270 (200)
200 (150)
160 (120)
130 (100)
110 (85)
70 (55)
50 (40)
20 (15)
25 (20)
30 (25)
40 (30)
45 (35)
45 (35)
45 (35)
45 (35)
45 (35)
30 (25)
25 (20)
MR
DC
< 0.5DC
< 1DC
< 1.5DC
JR
< 0.25DC
< 2.5DC
Depth of
cut
< 2DC
LR
(MAX. 30mm)
(MAX. 10mm)
(DC < & 30)

(DC > & 30)
< 0.1DC
< 3DC
(MAX. 100mm)
( ) : Indicates standard revolution and feed rate for slotting with MR.
DC:Dia.
SOLID END MILLS
Work
material
Decrease the revolution shown above by 10 20% and the feed rate by 20 30% for JR.
Decrease the revolution shown above by 20 30% and the feed rate by 30 50% for LR.
Supply cutting fluid sufficiently during cutting.
When the diameter exceeds 30 and the metal removal is less than the quantity shown in the table, the revolution and feed rate may be
1)
2)
3)
4)
J433
Memo
J434
Memo
J435
iMX END MILL SERIES
Copper Alloy
Cutting Conditions
Dimensions
Aluminium Alloy
M
iMX-S3HV
Size
Range
H
Shape
Page Number
Work Material
P
Product
Code
Coolant hole
Long Cutting Edge Type
Applications,
Features
Type
No. of Flutes
HEAD
SQUARE
Square head, 3 flute, Irregular helix
&10 &25
J439 J458

&10 &32
Materials
iMX-S4HV
NEW
iMX-S4HV-S
Square head, 4 flute, Irregular helix, Long

cutting edge type
Square head with coolant hole, 4 flute,

Irregular helix
J440
e
&16, &20
J464
J440 J463
&10 &25 a
J461
J441 J461
Square head, 3 flute, For aluminium alloy

For Machining of
Aluminium Alloys
&10 &28
iMX-S3A
J442 J469
RADIUS
Corner radius head, 4 flute, Irregular helix
&10 &28
iMX-C4HV
NEW
iMX-C4HV-S
iMX-C6HV
10
12
For High Feed

Machining
For High Efficiency

Machining
For Machining of
Aluminium Alloys
J436
Corner radius head, 4 flute, Irregular helix,

with coolant hole
&16, &20
J461
J464
J448 J463
&10 &25 a
&10, &12
J450 J471
iMX-C10HV
&16
J450 J471
iMX-C12HV
&20, &25
J450 J471
&10 &25 a
&10 &25
Materials
NEW
Corner radius head, 4 flute, Irregular helix,

Long cutting edge type
J447
iMX-C4FD-C
iMX-C4FV
iMX-C3A
Corner radius head, Multi-flute,

Irregular helix
With coolant hole Multi-task corner radius end mill for

high feed cutting
Corner radius head for high efficiency machining,

4 flute, Irregular helix
Corner radius head, 3 flute,

For aluminium alloy
&10 &28
J449 J461
J451 J467
J452 J468
J453 J469
Cutting Conditions
J443 J465
&10 &25
J444 J472
&10 &25 a
J445 J472
&10 &25
Dimensions
Aluminium Alloy
&10 &25
Size
Range
Copper Alloy
Shape
Product
Code
Coolant hole
Long Cutting Edge Type
No. of Flutes
Applications,
Features
Type
Page Number
Work Material
P
ROUGHING
Roughing head, 4 flute
Materials
iMX-R4F
BALL
Ball nose head, 4 flute, Irregular helix
Materials
iMX-B4HV
iMX-B4HV-E
iMX-B6HV
Ball nose head with coolant hole, 4 flute,

Irregular helix
HOLDERS
The undercut type is available in medium, semi-long, and long lengths.
Figure
Length
Taper angle one side Tool material
Undercut
Medium
Semi long
Long
Carbide
Straight
Semi long
Long
Carbide
Taper neck
Long
Carbide
NEW
J446 J473
J437

CARBIDE
IDENTIFICATION
iMX END MILL SERIES
y HEAD
x Basic configurations
Square
S
C
Corner radius
n Dia.
v Specifications
H
High helix
Vibration controle
For High Efficiency Machining
Ball nose
Roughing
Multi-task corner radius
Fine pitch
(Roughing)
IMX12
z Series DescriptionFastening size

IMX10
For 10mm
IMX12
For 12mm
IMX16
For 16mm
IMX20
For 20mm
IMX25
For 25mm
HV
v
, Coolant hole
Peripheral(Side)
ex.
R050 | 0.5mm
R100 | 1mm
End
End cutting edge(Center)
None
without hole
120
R100
12
c No. of Flutes
b Dia.
m Flute length
ex.
4 | 4 flute
ex.
120 | 12mm
ex.
12 | 12. mm
(Truncate decimal places)
y CARBIDE HOLDER
c Figure
Hyphen Indicates these are holders.
IMX12
IMX10
For 10mm
IMX12
For 12mm
IMX16
For 16mm
IMX20
For 20mm
IMX25
For 25mm
Straight
Undercut
1 Taper neck
U
x
z Series DescriptionFastening size
12
n Overall Length
ex.
L080 | 80mm
N017
L080
b Neck Length
v Shank diameter
ex.
N017 | 17. mm
(Truncate decimal places)
ex.
12 | 12mm
y RUN-OUT ACCURACY AND HEAD EXCHANGE ACCURACY

Unit : mm
Dia. DC
J438
Run-out accuracy for the peripheral cutting edge Head exchange accuracy (Axial)
<25
0.015
>25
0.020
0.02
m Tool material
C
CARBIDE
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
BD
Hardened Steel
( < 55HRC)
42
43.5
45
UWC
DC
Type1
SQUARE
iMX-S3HV
APMX
BALL
LH
0
- 0.020
DC>12
0
- 0.030
a3-flute end mills that cover side milling, slotting and plunging.
aIrregular lead controls vibration and achieves stable machining.
DC
APMX
LH
BD
IMX10S3HV10008
IMX12S3HV12010
IMX16S3HV16013
IMX20S3HV20017
IMX25S3HV25021
10
12
16
20
25
8.5
10.1
13.3
17
21
16
19
24
30
37.5
9.7
11.7
15.5
19.5
24.5
3
3
3
3
3
Grade
EP7020
Order Number
No. of
Flutes
Unit : mm
Type
1
1
1
1
1
a
a
a
a
RADIUS
DC < 12
* The fastening size of the holder and head should be the same. (refer to J438)

CUTTING CONDITIONS
J458
J439
iMX-S4HV
CARBIDE
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
SQUARE
BD
Hardened Steel
( < 55HRC)
42
45
UWC
Type1
APMX
DC
BALL
BD
LH
DC < 12
0
- 0.020
APMX
DC>12
APMX
LH
0
- 0.030
a Irregular lead controls vibration and achieves stable machining even when
NEW
NEW
NEW
NEW
Order Number
DC
APMX
LH
BD
IMX10S4HV10010
IMX10S4HV12012
IMX12S4HV12012
IMX12S4HV14014
IMX16S4HV16016
IMX16S4HV18018
IMX20S4HV20021
IMX20S4HV22023
IMX25S4HV25026
IMX25S4HV28029
IMX25S4HV30031
IMX25S4HV32033
10
12
12
14
16
18
20
22
25
28
30
32
10.5
12.5
12.5
14.5
16.5
18.5
21
23
26
29
31
33
16
19
19
22.5
24
27
30
33
37.5
41.5
43.5
45.5
9.7
9.7
11.7
11.7
15.5
15.5
19.5
19.5
24.5
24.5
24.5
24.5
4
4
4
4
4
4
4
4
4
4
4
4
Grade
EP7020
NEW
Unit : mm
No. of
Flutes
RADIUS
NEW
Curved
Edge
Offset Type
machining of difficult-to-cut materials and long overhang.
NEW
Type
1
2
1
2
1
2
1
2
1
2
2
2
a
a
a
a
a
a
a
a
a
a
a
J461
BD
CUTTING CONDITIONS
Type3
DC
Type2
APMX
APMX
LH
y Long cutting edge type

Order Number
DC
APMX
LH
BD
IMX16S4HV16032
IMX20S4HV20040
16
20
32
40
40
50
15.5
19.5
4
4
Grade
EP7020
NEW
Unit : mm
No. of
Flutes
NEW
Curved
Edge
Type
3
3
J440

CUTTING CONDITIONS
J461
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
BD
Hardened Steel
( < 55HRC)
42
45
UWC
DC
Type1
APMX
Peripheral cutting edge with coolant hole
SQUARE
iMX-S4HV-S
Square head with coolant hole, 4 flute, Irregular helix
LH
BALL
Peripheral cutting edge with coolant hole
0
- 0.020
DC>12
0
- 0.030
a Coolant holes for each cutting edge enable stable coolant supply.
a Irregular lead controls vibration and achieves stable machining.
DC
APMX
LH
BD
No. of
Flutes
IMX10S4HV10010S
IMX12S4HV12012S
IMX16S4HV16016S
IMX20S4HV20021S
IMX25S4HV25026S
10
12
16
20
25
10.5
12.5
16.5
21
26
16
19
24
30
37.5
9.7
11.7
15.5
19.5
24.5
4
4
4
4
4
EP7020
Order Number
Grade
Type
1
1
1
1
1
a
a
a
a
The fastening size of the holder and head should be the same. (refer to J438)
Unit : mm
RADIUS
DC < 12
CUTTING CONDITIONS
J461
J441
iMX-S3A
Square head, 3 flute, For aluminium alloy
CARBIDE
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
37.5
UWC
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
Type1
DC
SQUARE
BD
APMX
BALL
DC
BD
LH
DC < 12
0
- 0.020
Type2
APMX
DC>12
APMX
LH
0
- 0.030
Offset Type
Curved
Edge
a High efficiency machining due to the sharp cutting edge suitable for aluminium alloy machining and
NEW
NEW
NEW
NEW
DC
APMX
LH
BD
IMX10S3A10008
IMX10S3A12010
IMX12S3A12010
IMX12S3A14011
IMX16S3A16013
IMX16S3A18014
IMX20S3A20017
IMX20S3A22018
IMX25S3A25021
IMX25S3A28023
10
12
12
14
16
18
20
22
25
28
8.5
10.1
10.1
11.7
13.3
14.9
17
18.6
21
23.4
16
19
19
22.5
24
27
30
33
37.5
41.5
9.7
9.7
11.7
11.7
15.5
15.5
19.5
19.5
24.5
24.5
3
3
3
3
3
3
3
3
3
3
Type
1
2
1
2
1
2
1
2
1
2
a
a
a
a
a
a
a
a
a
J442
Order Number
Grade
ET2020
NEW
Unit : mm
No. of
Flutes
RADIUS
polished rake face.

CUTTING CONDITIONS
J469
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
35
CARBIDE
Aluminium Alloy
BD
UWC
DC
Type1
APMX
SQUARE
iMX-R4F
BALL
LH
LH
BD
IMX10R4F10010
IMX12R4F12012
IMX16R4F16016
IMX20R4F20021
IMX25R4F25026
10
12
16
20
25
10.5
12.5
16.5
21
26
16
19
24
30
37.5
9.7
11.7
15.5
19.5
24.5
4
4
4
4
4
Type
1
1
1
1
1
a
a
a
a
RADIUS
APMX
Grade
EP7020
DC
Unit : mm
Order Number
No. of
Flutes
a Roughing cutting edge reduces the cutting resistance. Effective when the rigidity of the machine or workpiece is low.
CUTTING CONDITIONS
J465
J443

CARBIDE
iMX-B4HV
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
Type1
DC
SQUARE
BD
Hardened Steel
( < 55HRC)
45
UWC
PRFRAD
APMX
BALL
LH
DC < 12
DC>12
0.010
0.020
DC < 12
DC>12
0
- 0.020
0
- 0.030
for long overhang applications.
Unit : mm
PRFRAD
DC
APMX
LH
BD
IMX10B4HV10010
IMX12B4HV12012
IMX16B4HV16016
IMX20B4HV20021
IMX25B4HV25026
5
6
8
10
12.5
10
12
16
20
25
10.5
12.5
16.5
21
26
16
19
24
30
37.5
9.7
11.7
15.5
19.5
24.5
4
4
4
4
4
Grade
EP7020
Order Number
No. of
Flutes
RADIUS
a The variable curve cutting edge controls vibraion and achieves stable machining of difficult-to-cut materilas and
Type
1
1
1
1
1
a
a
a
a
J444

CUTTING CONDITIONS
J472
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
BD
Hardened Steel
( < 55HRC)
45
UWC
DC
Type1
End cutting edge with coolant hole
DC>12
0.010
0.020
DC < 12
DC>12
0
- 0.020
APMX
LH
End cutting edge with coolant hole
BALL
DC < 12
PRFRAD
SQUARE
iMX-B4HV-E
Ball nose head with coolant hole, 4 flute, Irregular helix
0
- 0.030
machining of difficult-to-cut materilas and for long overhang applications.

PRFRAD
DC
APMX
LH
BD
IMX10B4HV10010E
IMX12B4HV12012E
IMX16B4HV16016E
IMX20B4HV20021E
IMX25B4HV25026E
5
6
8
10
12.5
10
12
16
20
25
10.5
12.5
16.5
21
26
16
19
24
30
37.5
9.7
11.7
15.5
19.5
24.5
4
4
4
4
4
Grade
EP7020
Order Number
No. of
Flutes
Unit : mm
Type
1
1
1
1
1
a
a
a
a
RADIUS
a The variable curve cutting edge controls vibraion and achieves stable
CUTTING CONDITIONS
J472
J445

CARBIDE
iMX-B6HV
45
UWC

(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
DC
SQUARE
BD
Hardened Steel
( < 55HRC)
PRFRAD
Type1
APMX
DC < 12
0.020
DC < 12
DC>12
0
- 0.020
0
- 0.030
a The variable curve cutting edge controls vibraion and achieves stable machining of difficult-to-cut materilas and for long overhang applications.
a 6 flutes enable high machining efficiency.
Unit : mm
Order Number
PRFRAD
DC
APMX
LH
BD
No. of
Flutes
RADIUS
DC>12
0.010
IMX10B6HV10010
IMX12B6HV12012
IMX16B6HV16016
IMX20B6HV20021
IMX25B6HV25026
5
6
8
10
12.5
10
12
16
20
25
10.5
12.5
16.5
21
26
16
19
24
30
37.5
9.7
11.7
15.5
19.5
24.5
6
6
6
6
6
Grade
EP7020
BALL
LH
Type
1
1
1
1
1
a
a
a
a
J446

CUTTING CONDITIONS
J473
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
DC
BD
Hardened Steel
( < 55HRC)
42
45
UWC
Type1
SQUARE
iMX-C4HV
APMX
RE
DC
Type2
0.020
APMX
DC>12
RE
0
- 0.030
a Vibration control corner radius type achieving the stable machining of difficult-to-cut
APMX
LH
Offset Type
materials and for long overhang applications due to the irregular helix.
NEW
NEW
NEW
NEW
NEW
Order Number
DC
RE
APMX
LH
BD
IMX10C4HV100R05010
IMX10C4HV100R10010
IMX10C4HV100R15010
IMX 10C4HV100R20010
IMX10C4HV100R25010
IMX10C4HV100R30010
IMX10C4HV120R10012
IMX10C4HV120R20012
IMX12C4HV120R05012
IMX12C4HV120R10012
IMX12C4HV120R15012
IMX12C4HV120R20012
IMX12C4HV120R25012
IMX12C4HV120R30012
IMX12C4HV120R40012
IMX12C4HV140R10014
IMX12C4HV140R20014
IMX16C4HV160R05016
IMX16C4HV160R10016
IMX16C4HV160R15016
IMX16C4HV160R20016
IMX16C4HV160R25016
IMX16C4HV160R30016
IMX16C4HV160R40016
IMX16C4HV160R50016
IMX16C4HV180R10018
IMX16C4HV180R30018
IMX20C4HV200R05021
IMX20C4HV200R10021
IMX20C4HV200R15021
IMX20C4HV200R20021
IMX20C4HV200R25021
IMX20C4HV200R30021
IMX20C4HV200R40021
IMX20C4HV200R50021
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
14
14
16
16
16
16
16
16
16
16
18
18
20
20
20
20
20
20
20
20
0.5
1
1.5
2
2.5
3
1
2
0.5
1
1.5
2
2.5
3
4
1
2
0.5
1
1.5
2
2.5
3
4
5
1
3
0.5
1
1.5
2
2.5
3
4
5
10.5
10.5
10.5
10.5
10.5
10.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12
14.5
14.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
16.5
18.5
18.5
21
21
21
21
21
21
21
21
16
16
16
16
16
16
19
19
19
19
19
19
19
19
19
22.5
22.5
24
24
24
24
24
24
24
24
27
27
30
30
30
30
30
30
30
30
9.7
9.7
9.7
9.7
9.7
9.7
9.7
9.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
15.5
15.5
15.5
15.5
15.5
15.5
15.5
15.5
15.5
15.5
19.5
19.5
19.5
19.5
19.5
19.5
19.5
19.5
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Grade
EP7020
NEW
Unit : mm
No. of
Flutes
NEW
Curved
Edge
Type
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
RADIUS
0
- 0.020
DC < 12
BALL
BD
LH
J447
iMX-C4HV
NEW
NEW
NEW
Order Number
DC
RE
APMX
LH
BD
IMX20C4HV200R63521
IMX20C4HV220R10023
IMX20C4HV220R30023
IMX25C4HV250R10026
IMX25C4HV250R20026
IMX25C4HV250R30026
IMX25C4HV250R40026
IMX25C4HV250R50026
IMX25C4HV250R63526
IMX25C4HV280R10029
IMX25C4HV280R30029
20
22
22
25
25
25
25
25
25
28
28
6.35
1
3
1
2
3
4
5
6.35
1
3
21
23
23
26
26
26
26
26
26
29
29
30
33
33
37.5
37.5
37.5
37.5
37.5
37.5
41.5
41.5
19.5
19.5
19.5
24.5
24.5
24.5
24.5
24.5
24.5
24.5
24.5
4
4
4
4
4
4
4
4
4
4
4
Grade
EP7020
NEW
Unit : mm
No. of
Flutes
BALL
SQUARE
CARBIDE
Type
1
2
2
1
1
1
1
1
1
2
2
a
a
a
a
a
a
a
a
a
a
J461
Type3
DC
RADIUS
BD
CUTTING CONDITIONS
APMX
RE
APMX
LH
y Long cutting edge type
NEW
NEW
DC
RE
APMX
LH
BD
IMX16C4HV160R10032
IMX16C4HV160R30032
IMX20C4HV200R10040
IMX20C4HV200R30040
16
16
20
20
1
3
1
3
32
32
40
40
40
40
50
50
15.5
15.5
19.5
19.5
4
4
4
4
Type
3
3
3
3
a
a
a
J448
Order Number
Grade
EP7020
NEW
Unit : mm
No. of
Flutes
NEW
Curved
Edge

CUTTING CONDITIONS
J461
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
DC
BD
Hardened Steel
( < 55HRC)
42
45
UWC
Type1
SQUARE
iMX-C4HV-S
Corner radius head, 4 flute, Irregular helix, with coolant hole
APMX
(Peripheral cutting edge with coolant hole)
RE
LH
BALL
(Peripheral cutting edge with coolant hole)
0.020
0
- 0.020
DC>12
0
- 0.030
DC
RE
APMX
LH
BD
IMX10C4HV100R10010S
IMX12C4HV120R10012S
IMX16C4HV160R10016S
IMX20C4HV200R10021S
IMX25C4HV250R10026S
10
12
16
20
25
1
1
1
1
1
10.5
12.5
16.5
21
26
16
19
24
30
37.5
9.7
11.7
15.5
19.5
24.5
4
4
4
4
4
Unit : mm
Grade
EP7020
Order Number
No. of
Flutes
a Irregular lead controls vibration and achieves stable machining even on difficult-to-cut materials and long overhang applications.
Type
1
1
1
1
1
a
a
a
a
RADIUS
DC < 12
CUTTING CONDITIONS
J461
J449
iMX-C6HV/C10HV/C12HV
Corner radius head, Multi-flute, Irregular helix
CARBIDE
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
DC <12
Austenitic
Stainless Steel
Titanium Alloy,
44.5
45
DC>12
DC <12
Copper Alloy
DC>12
Aluminium Alloy
DC
SQUARE
BD
Hardened Steel
( < 55HRC)
43.5
45
UWC
Type1
APMX
RE
DC
BALL
BD
LH
DC < 12
0
- 0.020
DC>12
APMX
RE
0
- 0.030
LH
a High machining efficiency due to the multi-flute design.

Order Number
DC
RE
APMX
LH
BD
IMX10C6HV100R05010
IMX10C6HV100R10010
IMX12C6HV120R10012
IMX16C10HV160R10016
IMX20C12HV200R10021
IMX25C12HV250R10026
10
10
12
16
20
25
0.5
1
1
1
1
1
10.5
10.5
12.5
16.5
21
26
16
16
19
24
30
37.5
9.7
9.7
11.7
15.5
19.5
24.5
6
6
6
10
12
12
Grade
EP7020
NEW
Unit : mm
No. of
Flutes
RADIUS
Type2
0.020
Type
1
1
1
2
2
2
a
a
a
a
a
J450

CUTTING CONDITIONS
J471
NEW
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
DC
BD
Hardened Steel
( < 55HRC)
45
UWC
Type1
APMX
LF
(With end cutting edge center coolant hole)
SQUARE
iMX-C4FD-C
With coolant hole Multi-task corner radius end mill for high feed cutting
LH
BALL
(With end cutting edge center coolant hole)
0
- 0.020
DC>12
0
- 0.030
a Multi-task corner radius type and 4 flutes offer high feed and high efficiency.
a Coolant hole with the end cutting edge as the center provides a stable supply of coolant.
IMX10C4FD10010C
IMX12C4FD12012C
IMX16C4FD16016C
IMX20C4FD20021C
IMX25C4FD25026C
10
12
16
20
25
1.99
2.1
2.75
3.07
4.21
APMX
LF
LH
BD
0.7
0.8
1
1.3
1.6
10.5
12.5
16.5
21
26
16
19
24
30
37.5
9.7
11.7
15.5
19.5
24.5
4
4
4
4
4
Grade
2.1
2.8
3
3.3
4.5
EP7020
DC
*
RMPX
Order Number
1
RE *
No. of
Flutes
Unit : mm
Type
1
1
1
1
1
a
a
a
a
Order Number
IMX10C4FD10010C
IMX12C4FD12012C
IMX16C4FD16016C
IMX20C4FD20021C
IMX25C4FD25026C
RE *
1.99
2.1
2.75
3.07
4.21
fastening size of the holder and head should be the same. (refer to J438)
* The
Multi-task corner radius is not suitable for corner radius milling that transfers an R-shape because cutting at R is incomplete.
*1 RE : Approx. R
*2 RMPX : Max. Ramping Angle
*
Multi-task radius part
Xb
Ra
Rb
0.27
0.33
0.42
0.59
0.67
1.7
2.25
3.1
4
5
1.5
1.5
2
2
3
5
6
8
10
12
Rb
RADIUS
DC < 12
Ra
Xb
K
RE
Please programme CAM as an

R2 cutter radius, when using
the iMX.
The approximate uncut portions
for the programme are as
follows.
CUTTING CONDITIONS
J467
J451

CARBIDE
iMX-C4FV
Corner radius head for high efficiency machining, 4 flute, Irregular helix
(<30HRC)
( < 45HRC)
Hardened Steel
(>55HRC)
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
Aluminium Alloy
Type1
DC
SQUARE
BD
Hardened Steel
( < 55HRC)
43
45
UWC
APMX
BALL
RE
DC < 20
0.020
DC < 12
DC>12
0
- 0.030
a Corner radius end mill for high efficiency machining

Unit : mm
DC
RE
APMX
LH
BD
IMX10C4FV100R20010
IMX12C4FV120R20012
IMX16C4FV160R30016
IMX20C4FV200R30021
IMX25C4FV250R40026
10
12
16
20
25
2
2
3
3
4
10.5
12.5
16.5
21
26
16
19
24
30
37.5
9.7
11.7
15.5
19.5
24.5
4
4
4
4
4
Grade
EP6120
Order Number
No. of
Flutes
RADIUS
DC>20
0.010
0
- 0.020
LH
Type
1
1
1
1
1
a
a
a
a
J452

CUTTING CONDITIONS
J468
iMX-C3A
Corner radius head, 3 flute, For aluminium alloy
(<30HRC)
( < 45HRC)
Hardened Steel
( < 55HRC)
Hardened Steel
(>55HRC)
37.5
UWC
Austenitic
Stainless Steel
Titanium Alloy,
Copper Alloy
CARBIDE
Aluminium Alloy
DC
Type1
RE
SQUARE
BD
APMX
0.020
DC < 12
0
- 0.020
Type2
APMX
DC>12
APMX
RE
0
- 0.030
LH
BALL
DC
BD
LH
Curved
Edge
Offset Type
NEW
NEW
NEW
NEW
NEW
RE
APMX
LH
BD
10
10
12
12
12
14
16
16
18
20
20
22
25
25
25
28
1
2.5
1
1
3.2
1
1
3.2
3.2
1
3.2
3.2
1
3.2
5
3.2
8.5
8.5
10.1
10.1
10.1
11.7
13.3
13.3
14.9
17
17
18.6
20
21
21
23.4
16
16
19
19
19
22.5
24
24
27
30
30
33
37.5
37.5
37.5
41.5
9.7
9.7
9.7
11.7
11.7
11.7
15.5
15.5
15.5
19.5
19.5
19.5
24.5
24.5
24.5
24.5
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
Grade
ET2020
NEW
IMX10C3A100R10008
IMX10C3A100R25008
IMX10C3A120R10010
IMX12C3A120R10010
IMX12C3A120R32010
IMX12C3A140R10011
IMX16C3A160R10013
IMX16C3A160R32013
IMX16C3A180R32014
IMX20C3A200R10017
IMX20C3A200R32017
IMX20C3A220R32018
IMX25C3A250R10020
IMX25C3A250R32021
IMX25C3A250R50021
IMX25C3A280R32023
DC
No. of
Flutes
Order Number
Unit : mm
Type
1
1
2
1
1
2
1
1
2
1
1
2
1
1
1
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
polished rake face.
RADIUS
a High efficiency machining due to the sharp cutting edge suitable for aluminium alloy machining and
CUTTING CONDITIONS
J469
J453
iMX
Carbide Holder
CARBIDE
DCON
LB
Type1
DCON
BD
y Undercut
Type2
LF
y Straight
LF
y Taper neck type

BD
DCON
BHTA
Type3
LB
h6
LF
DCON=10 12 < DCON < 16 20 < DCON < 25

0
- 0.009
0
- 0.011
0
- 0.013
y Carbide Holder
IMX10-U10N014L070C
IMX10-S10L090C
IMX10-U10N034L090C
IMX10-S10L110C
IMX10-U10N054L110C
IMX10-A12N054L110C
IMX12-U12N017L080C
IMX12-S12L100C
IMX12-U12N041L100C
IMX12-S12L130C
IMX12-U12N065L130C
IMX12-A16N065L130C
IMX16-U16N024L080C
IMX16-S16L110C
IMX16-U16N056L110C
IMX16-S16L150C
IMX16-U16N088L150C
IMX16-A20N088L150C
IMX20-U20N030L090C
IMX20-S20L130C
IMX20-U20N070L130C
IMX20-S20L180C
IMX20-U20N110L180C
IMX20-A25N110L180C
IMX25-U25N037L110C
IMX25-S25L160C
IMX25-U25N087L160C
IMX25-S25L210C
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
LB
14
34
54
54
17
41
65
65
24
56
88
88
30
70
110
110
37.5
87.5
BD
9.7
9.7
9.7
9.7
11.7
11.7
11.7
11.7
15.5
15.5
15.5
15.5
19.5
19.5
19.5
19.5
24.5
24.5
LF
70
90
90
110
110
110
80
100
100
130
130
130
80
110
110
150
150
150
90
130
130
180
180
180
110
160
160
210
DCON
10
10
10
10
10
12
12
12
12
12
12
16
16
16
16
16
16
20
20
20
20
20
20
25
25
25
25
25
a
J454
BHTA
Stock
Order Number
Unit : mm
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Type Suitable Head
1
2
1
2
1
3
1
2
1
2
1
3
1
2
1
2
1
3
1
2
1
2
1
3
1
2
1
2
IMX10
IMX10
IMX10
IMX10
IMX10
IMX10
IMX12
IMX12
IMX12
IMX12
IMX12
IMX12
IMX16
IMX16
IMX16
IMX16
IMX16
IMX16
IMX20
IMX20
IMX20
IMX20
IMX20
IMX20
IMX25
IMX25
IMX25
IMX25
Wrench
Anti-seize
Lubricant
IMX10-WR
IMX10-WR
IMX10-WR
IMX10-WR
IMX10-WR
IMX10-WR
IMX12-WR
IMX12-WR
IMX12-WR
IMX12-WR
IMX12-WR
IMX12-WR
IMX16-WR
IMX16-WR
IMX16-WR
IMX16-WR
IMX16-WR
IMX16-WR
IMX20-WR
IMX20-WR
IMX20-WR
IMX20-WR
IMX20-WR
IMX20-WR
IMX25-WR
IMX25-WR
IMX25-WR
IMX25-WR
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
MK1KS
CARBIDE
HOW TO INSTALL THE HEAD

a Before installing remove all the dust and oil etc. Remove also the anti-rust oil from a new head.
Coat only the screw part of the head with a small amount of anti-seize compound. If too much compound is used, during
tightening, the anti-seize compound may enter the taper part and have a large effect on the coupling mechanism. Wipe off
the anti-seize compound and make adjustments.
Be careful that there is no anti-seize compound sticking inside the taper when inserting the head into the holder.
Wipe off oil and dust.
anti-seize compound
(only screw part)
a Be careful because you may cut your hand if you touch the edge of the blade directly when tightening.
There is still a clearance in this state, use the accessory wrench to tighten until the face of the head and holder fit snugly together.
a Refer to the table below for the necessary recommended torque angle.
Clearance
Fastening size
iMX10
iMX12
iMX16
iMX20
iMX25
No clearance
If regulating more strictly, use the torque wrench to tighten by the recommended torque below.
Recommended
Reference
tightening angle clamping torque (Nm)
50
50
50
40
35
10
15
30
50
75
Note 1) Do not handle cutting edges with bare

hands.
Note 2) Please use the wrench provided. It is
thinner than a standard wrench to prevent
damage to the flutes when tightening.
J455

CARBIDE
iMX holder application

a Combination of the straight type and standard head causes interference when the depth of cut is head length or more. (Because holder diameter = head diameter)
a Combination of the straight type and offset head may make the depth of cutting length or more. (Because holder diameter < head diameter)
Straight + Standard head
Straight + Offset head
No contact
Use straight type

and standard head
combination at a depth
of cut of the head
length or less.
Depth of cut < Head length

Depth of
cut
Length of cut
Depth of
cut
Head length
Installation at an overhang of 3D or less is also possible,

if the depth of cut < head length is assumed.
a It is suitable for vertical wall machining, because the undercut type has a relief neck.
a A taper neck with thick relief has high rigidity. Especially a stable cutting is demonstrated at deeper machining.
a Perform straight shank additional grinding together with customer application for undercut taper neck type.
J456
Undercut + Standard head
Taper neck + Standard head
BHTA
Workpiece angle
No contact
(Refer to the cutting edge diameter (BD) of each type for the minimum machining diameter.)
Correction factor by recommended cutting condition overhang length (SIDE MILLING)
CARBIDE
Use by multiplying the recommended cutting condition on the next page by the correction factor by overhang length.
Refer to each recommended condition for the long cutting and offset type.
L/D
Carbon steel, Alloy steel, Mild Steel, Copper,

Copper alloys
Pre-hardened steel, Carbon steel, Alloy steel,

Alloy tool steel

Ferritic, Precipitation hardening stainless steel, Titanium alloy
AISI P21, AISI P20, AISI 4340, SKD, SKT
AISI 304, AISI 316, AISI 304LN, AISI 316LN,

AISI 410, AISI 430, AISI 431, AISI 420J2, Ti-6Al-4V
Cutting Speed Main Spindle Revolution Feed per Tooth Cutting Width Cutting Speed Main Spindle Revolution Feed per Tooth Cutting Width Cutting Speed Main Spindle Revolution Feed per Tooth Cutting Width
(m/min)
(min-1)
(mm/t.)
ae (mm)
(m/min)
(min-1)
(mm/t.)
ae (mm)
(m/min)
(min-1)
(mm/t.)
ae (mm)
2
3
4
100%
100%
80%
100%
100%
80%
100%
100%
90%
100%
100%
70%
100%
100%
80%
100%
100%
80%
100%
100%
90%
100%
100%
70%
100%
100%
80%
100%
100%
80%
100%
100%
90%
100%
100%
70%
60%
60%
80%
40%
60%
60%
80%
40%
60%
60%
80%
40%
50%
50%
70%
30%
50%
50%
70%
30%
50%
50%
70%
30%
40%
40%
70%
20%
40%
40%
70%
20%
30%
30%
60%
20%
8
9
40%
30%
40%
30%
60%
60%
10%
10%
40%
30%
40%
30%
60%
60%
10%
10%
30%
20%
30%
20%
50%
50%
10%
10%
Work
material
L/D
Precipitation hardening stainless steel,

Cobalt chromium alloy
AISI 630, AISI 631
Inconel718
Cutting Speed Main Spindle Revolution Feed per Tooth Cutting Width Cutting Speed Main Spindle Revolution Feed per Tooth Cutting Width
(m/min)
(min-1)
(mm/t.)
ae (mm)
(m/min)
(min-1)
(mm/t.)
ae (mm)
2
3
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
4
5
6
7
8
9
80%
60%
50%
30%
30%
20%
80%
60%
50%
30%
30%
20%
90%
80%
70%
60%
50%
50%
70%
40%
30%
20%
10%
10%
80%
60%
50%
30%
30%
20%
80%
60%
50%
30%
30%
20%
90%
80%
70%
60%
50%
50%
70%
40%
30%
20%
10%
10%
Work
material
J457

CARBIDE
iMX-S3HV
SQUARE

y Side milling
Work
material

Copper alloys

Alloy tool steel


BALL
Dia. Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
Revolution
per Min.
Revolution
per Min.
DC (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) ae (mm)
10
12
150
150
4800 0.09
4000 0.09
16
150
20
25
150
150
1300
1100
8
9.6
2
2.4
120
120
3800 0.06
3200 0.065
680
620
8
9.6
2
2.4
100
100
3200 0.075
2700 0.08
720
650
8
9.6
2
2.4
3000 0.1
900 12.8
3.2
120
2400 0.075
540
12.8
3.2
100
2000 0.09
540
12.8
3.2
2400 0.1
1900 0.12
720 16
680 20
4
5
120
120
1900 0.075
1500 0.075
430
340
16
20
4
5
100
100
1600 0.09
1300 0.09
430
350
16
20
4
5
ae
RADIUS
Depth of
cut
ap
DC:Dia.
Work
material

AISI 630, AISI 631
Inconel718
Dia. Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
Revolution
per Min.
DC (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) ae (mm)
J458
10
12
75
75
2400 0.06
2000 0.065
430
390
8
9.6
2
2.4
40
40
1300 0.04
1100 0.045
160
150
8
9.6
1
1.2
16
75
1500 0.075
340
12.8
3.2
40
800 0.05
120
12.8
1.6
20
25
75
75
1200 0.075
950 0.075
270
210
16
20
4
5
40
40
640 0.05
510 0.05
96
77
16
20
2
2.5
ae
Depth of
cut
ap
DC:Dia.
3) The irregular helix flute end mill has a large effect on controlling vibration when compared to standard end mills. However, if the rigidity of
the machine or the workpiece installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and feed
iMX-S3HV
J439
iMX-S3HV
CARBIDE
y Slotting
Work
material

Copper alloys

Alloy tool steel


SQUARE
10
12
100
100
3200
2700
0.04
0.05
380
410
16
100
2000
0.07
420
80
1600
0.05
240
75
1500
0.06
270
20
25
100
100
1600
1300
0.07
0.08
340
310
10
12
80
80
1300
1000
0.05
0.05
200
150
10
12
75
75
1200
950
0.06
0.06
220
170
10
12
5
6
80
80
2500
2100
0.03
0.04
Depth of
cut
230
250
5
6
75
75
2400
2000
0.03
0.04
200
240
5
6

AISI 630, AISI 631
Inconel718
RADIUS
ap
DC:Dia.
Work
material
BALL
Dia. Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut
Revolution
per Min.
Revolution
per Min.
Revolution
per Min.
DC (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm)
Dia. Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut
Revolution
per Min.
Revolution
per Min.
DC (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm)
10
12
60
60
1900
1600
0.025
0.035
100
170
16
60
1200
0.05
180
30
600
0.05
90
3.2
20
25
60
60
950
760
0.05
0.05
140
110
10
12
30
30
480
380
0.05
0.05
72
57
4
5
30
30
950
800
0.02
0.03
57
72
2
2.4
ap
DC:Dia.
iMX-S3HV
J439
Depth of
cut
5
6
J459

CARBIDE
iMX-S3HV
SQUARE

y Plunging
Work
material

Copper alloys

Alloy tool steel


BALL
Dia
Cutting Speed Main Spindle Feed per Table Feed Drilled Depth Step Cutting Speed Main Spindle Feed per Table Feed Drilled Depth Step Cutting Speed Main Spindle Feed per Table Feed Drilled Depth Step
Revolution Revolution per Min.
DC (mm) (m/min) (min-1) (mm/rev) (mm/min) ap (mm) ap2 (mm) (m/min) (min-1) (mm/rev) (mm/min) ap (mm) ap2 (mm) (m/min) (min-1) (mm/rev) (mm/min) ap (mm) ap2 (mm)
10
12
16
100
100
100
3200
2700
2000
0.14
0.14
0.14
450
380
280
5
6
8
2.5
2.5
2.5
70
70
70
2200 0.09
1900 0.09
1400 0.09
200
170
130
5
6
8
2
2
2
60
60
60
1900 0.03
1600 0.03
1200 0.03
57
48
36
5
6
8
0.6
0.6
0.6
20
25
100
100
1600
1300
0.14
0.14
220
180
10
12.5
2.5
2.5
70
70
1100 0.09
890 0.09
99
80
10
12.5
2
2
60
60
950 0.03
760 0.03
29
23
10
12.5
0.6
0.6
RADIUS
Depth of
cut
ap
DC:Dia.
Work
material

AISI 630, AISI 631
Dia
Cutting Speed Main Spindle Feed per Table Feed Drilled Depth Step
DC (mm) (m/min) (min-1) (mm/rev) (mm/min) ap (mm) ap2 (mm)
J460
10
12
40
40
1300 0.03
1100 0.03
39
33
16
40
800 0.03
24
0.6
20
25
40
40
640 0.03
510 0.03
19
15
10
12.5
0.6
0.6
Depth of
cut
5
6
0.6
0.6
ap
DC:Dia.
iMX-S3HV
J439
iMX-S4HV/iMX-S4HV-S/iMX-C4HV/iMX-C4HV-S
Square/Corner radius, 4 flute, Irregular helix (With/Without coolant hole)
CARBIDE
y Side milling
Work
material

Copper alloys

Alloy tool steel


SQUARE
10
12
150
150
4800 0.09
4000 0.09
1700
1400
10
12
2
2.4
120
120
3800 0.06
910
3200 0.065 830
10
12
2
2.4
100
100
3200 0.075 960

2700 0.08
860
10
12
2
2.4
16
150
3000 0.1
1200
16
3.2
120
2400 0.075 720
16
3.2
100
2000 0.09
720
16
3.2
20
25
150
150
2400 0.1
1900 0.12
960
910
20
25
4
5
120
120
1900 0.075 570

1500 0.075 450
20
25
4
5
100
100
1600 0.09
1300 0.09
580
470
20
25
4
5
BALL
Dia
Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
Revolution
per Min.
Revolution
per Min.
ae
Depth of
cut
DC:Dia.
Work
material

AISI 630, AISI 631
Inconel718
RADIUS
ap
10
12
75
75
2400 0.06
580
2000 0.065 520
10
12
2
2.4
40
40
16
75
1500 0.075 450
16
3.2
40
800 0.05
20
25
75
75
1200 0.075 360

950 0.075 290
20
25
4
5
40
40
640 0.05
510 0.05
1300 0.04
210
1100 0.045 200
10
12
1
1.2
160
16
1.6
130
100
20
25
2
2.5
ae
Depth of
cut
ap
DC:Dia.
the machine or the workpiece installation is poor, vibration or abnormal sound can occur.
In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut.
iMX-S4HV
iMX-S4HV-S
iMX-C4HV
iMX-C4HV-S
J440
J441
J447
J449
Dia
Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
Revolution
per Min.
J461

CARBIDE
iMX-S4HV/iMX-S4HV-S/iMX-C4HV/iMX-C4HV-S
Square/Corner radius, 4 flute, Irregular helix (With/Without coolant hole)
SQUARE

y Slotting
Work
material

Copper alloys

Alloy tool steel


BALL
Dia
Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut
Revolution
per Min.
Revolution
per Min.
Revolution
per Min.
10
12
100
100
3200
2700
0.04
0.05
510
540
16
100
2000
0.07
560
80
1600
0.05
320
75
1500
0.06
360
20
25
100
100
1600
1300
0.07
0.08
450
420
10
12
80
80
1300
1000
0.05
0.05
260
200
10
12
75
75
1200
950
0.06
0.06
290
230
10
12
5
6
80
80
2500
2100
0.03
0.04
RADIUS
Depth of
cut
300
340
5
6
75
75
2400
2000
0.03
0.04
290
320
5
6
ap
DC:Dia.
Work
material

AISI 630, AISI 631
Inconel718
Dia
Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut
Revolution
per Min.
Revolution
per Min.
DC (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm)
10
12
60
60
1900
1600
0.025
0.035
190
220
16
60
1200
0.05
240
30
20
25
60
60
950
760
0.05
0.05
190
150
10
12
30
30
Depth of
cut
5
6
30
30
950
800
0.02
0.03
76
96
2
2.4
600
0.05
120
3.2
480
380
0.05
0.05
96
76
4
5
ap
DC:Dia.
iMX-S4HV
iMX-S4HV-S
J462
iMX-C4HV
iMX-C4HV-S
J440
J441
J447
J449
iMX-S4HV/iMX-C4HV
Square/Corner radius head, 4 flute, Irregular helix, Long cutting edge type
CARBIDE
y Side milling
Copper alloys

Alloy tool steel


Work material
4
6
Dia Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
Revolution
per Min.
Revolution
per Min.
16
20
16
20
100
100
60
60
2000
1600
1200
950
0.09
0.09
0.07
0.07
720
580
340
270
32
40
32
40
0.8
1
0.8
1
80
80
50
50
1600
1300
990
800
0.07
0.07
0.05
0.05
450
360
200
160
32
40
32
40
0.8
1
0.8
1
60
60
40
40
1200
950
800
640
0.08
0.08
0.06
0.06
380
300
190
150
32
40
32
40
0.8
1
0.8
1
BALL
L/D
SQUARE
ae
Depth of cut
ap

AISI 630, AISI 631
Inconel718
RADIUS
DC:Dia.
Work material
L/D
4
6
Dia Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
Revolution
per Min.
16
20
16
20
50
50
30
30
990
800
600
480
0.07
0.07
0.05
0.05
280
220
120
96
32
40
32
40
0.8
1
0.8
1
30
30
20
20
600
480
400
320
0.05
0.05
0.04
0.04
120
96
64
51
32
40
32
40
0.4
0.5
0.4
0.5
Depth of cut
ap
DC:Dia.
3) The irregular helix flute end mill has a large effect on controlling vibration when compared to standard end mills.
However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur.
4) The length of the long cutting type is 2 times that of the standard head. L/D demonstrates +1 when installed to a holder of the same size.
iMX-S4HV
iMX-C4HV
J440
J448
ae
J463

CARBIDE
iMX-S4HV/iMX-C4HV
Square/Corner radius head, 4 flute, Irregular helix, Offset type
SQUARE

y Side milling
BALL

Alloy tool steel


Work material
L/D
RADIUS

Copper alloys
Dia Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
Revolution
per Min.
Revolution
per Min.
12
14
<3
18
22
28
30
32
12
14
18
22
28
30
32
12
14
18
22
28
30
32
150
150
150
150
150
150
150
90
90
90
90
90
90
90
60
60
60
60
60
60
60
4000
3400
2700
2200
1700
1600
1500
2400
2000
1600
1300
1000
950
900
1600
1400
1100
870
680
640
600
0.09 1400
0.09 1200
0.1
1100
0.1
880
0.12 820
0.12 770
0.12 720
0.07 670
0.07 560
0.08 510
0.08 420
0.1
400
0.1
380
0.1
360
0.06 380
0.06 340
0.07 310
0.07 240
0.08 220
0.08 200
0.08 190
12
14
18
22
28
30
32
12
14
18
22
28
30
32
12
14
18
22
28
30
32
1.2
1.4
1.8
2.2
2.8
3
3.2
0.5
0.6
0.7
0.9
1.1
1.2
1.3
0.2
0.3
0.4
0.4
0.6
0.6
0.6
120
120
120
120
120
120
120
70
70
70
70
70
70
70
50
50
50
50
50
50
50
3200
2700
2100
1700
1400
1300
1200
1900
1600
1200
1000
800
740
700
1300
1100
880
720
570
530
500
0.06
0.065
0.075
0.075
0.075
0.075
0.075
0.05
0.05
0.06
0.06
0.06
0.06
0.06
0.04
0.05
0.05
0.05
0.05
0.05
0.05
770
700
630
510
420
390
360
380
320
290
240
190
180
170
210
220
180
140
110
110
100
12
14
18
22
28
30
32
12
14
18
22
28
30
32
12
14
18
22
28
30
32
1.2
1.4
1.8
2.2
2.8
3
3.2
0.5
0.6
0.7
0.9
1.1
1.2
1.3
0.2
0.3
0.4
0.4
0.6
0.6
0.6
100
100
100
100
100
100
100
60
60
60
60
60
60
60
32
32
32
32
32
32
32
2700
2300
1800
1400
1100
1100
990
1600
1400
1100
870
680
640
600
850
730
570
460
360
340
320
0.075
0.08
0.09
0.09
0.09
0.09
0.09
0.06
0.06
0.07
0.07
0.07
0.07
0.07
0.05
0.06
0.06
0.06
0.06
0.06
0.06
810
740
650
500
400
400
360
380
340
310
240
190
180
170
170
180
140
110
86
82
77
12
14
18
22
28
30
32
12
14
18
22
28
30
32
12
14
18
22
28
30
32
1.2
1.4
1.8
2.2
2.8
3
3.2
0.5
0.6
0.7
0.9
1.1
1.2
1.3
0.2
0.3
0.4
0.4
0.6
0.6
0.6
ae
Depth of cut
ap
DC:Dia.

AISI 630, AISI 631
Inconel718
Work material
L/D
Dia Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
Revolution
per Min.
12
14
<3
18
22
28
30
32
12
14
18
22
28
30
32
12
14
18
22
28
30
32
75
75
75
75
75
75
75
50
50
50
50
50
50
50
24
24
24
24
24
24
24
2000
1700
1300
1100
850
800
750
1300
1100
880
720
570
530
500
640
550
420
350
270
250
240
0.06
0.065
0.075
0.075
0.075
0.075
0.075
0.05
0.05
0.06
0.06
0.06
0.06
0.06
0.04
0.05
0.05
0.05
0.05
0.05
0.05
480
440
390
330
260
240
230
260
220
210
170
140
130
120
100
110
84
70
54
50
48
12
14
18
22
28
30
32
12
14
18
22
28
30
32
12
14
18
22
28
30
32
1.2
1.4
1.8
2.2
2.8
3
3.2
0.5
0.6
0.7
0.9
1.1
1.2
1.3
0.2
0.3
0.4
0.4
0.6
0.6
0.6
30
30
40
40
40
40
40
10
10
19
19
19
19
19
800
680
710
580
450
420
400
270
230
340
270
220
200
190
0.04
0.045
0.05
0.05
0.05
0.05
0.05
0.03
0.04
0.04
0.04
0.04
0.04
0.04
130
120
140
120
90
84
80
32
37
54
43
35
32
30
12
14
18
22
28
30
32
12
14
18
22
28
30
32
0.9
1.1
1.4
1.7
2.1
2.3
2.4
0.4
0.4
0.6
0.7
0.8
0.9
1.0
ae
Depth of cut
ap
DC:Dia.
J464
iMX-S4HV
iMX-C4HV
J440
J447
iMX-R4F
CARBIDE
y Side milling
Work
material

Copper alloys

Alloy tool steel


SQUARE
10
12
150
150
4800 0.045 860

4000 0.045 720
16
150
3000 0.05
20
25
150
150
2400 0.05
1900 0.06
8
9.6
4
4.8
120
120
3800 0.03
460
3200 0.033 420
8
9.6
600
12.8
6.4
120
2400 0.038 360
12.8
480
460
16
20
120
120
1900 0.038 290

1500 0.038 230
16
20
8
10
4
4.8
6.4
8
10
100
100
3200 0.038 480

2700 0.04
430
8
9.6
100
2000 0.045 360
12.8
100
100
1600 0.045 290

1300 0.045 230
16
20
4
4.8
6.4
8
10
BALL
Dia. Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
Revolution
per Min.
Revolution
per Min.
ae
Depth of
cut
DC:Dia.
Work
material

AISI 630, AISI 631
Inconel718
RADIUS
ap
10
12
75
75
2400 0.03
290
2000 0.033 260
8
9.6
4
4.8
40
40
16
75
1500 0.038 230
12.8
6.4
40
800 0.05
20
25
75
75
1200 0.038 180

950 0.038 140
16
20
40
40
640 0.05
510 0.05
8
10
1300 0.04
210
1100 0.045 200
8
9.6
1
1.2
160
12.8
1.6
130
100
16
20
2
2.5
Dia. Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
Revolution
per Min.
ae
Depth of
cut
ap
DC:Dia.
3) Vibration may occur if the rigidity of machine or workpiece is low.
iMX-R4F
J443
J465

CARBIDE
iMX-R4F
SQUARE

y Slotting
Work
material

Copper alloys

Alloy tool steel


BALL
Dia
Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut
Revolution
per Min.
Revolution
per Min.
Revolution
per Min.
10
12
100
100
3200
2700
0.04
0.045
510
490
16
100
2000
0.05
400
80
1600
0.038
240
20
25
100
100
1600
1300
0.05
0.06
320
310
10
12
80
80
1300
1000
0.038
0.038
200
150
5
6
RADIUS
Depth of
cut
80
80
2500
2100
0.03
0.032
300
270
5
6
60
60
1900
1600
0.02
0.025
150
160
60
1200
0.03
140
10
12
60
60
950
760
0.034
0.034
130
100
4
4.8
6.4
8
10
ap
DC:Dia.
Work
material

AISI 630, AISI 631
Dia
Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut
Revolution
per Min.
DC (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm)
J466
10
12
40
40
1300
1100
0.016
0.02
83
88
4
4.8
16
40
800
0.024
77
6.4
20
25
40
40
640
510
0.027
0.027
70
55
Depth of
cut
8
10
ap
DC:Dia.
3) Vibration may occur if the rigidity of machine or workpiece is low.In this case, please reduce the revolution and feed rate proportionately, or
set a lower depth of cut.
iMX-R4F
J443
iMX-C4FD-C
With coolant hole Multi-task corner radius end mill for high feed cutting
CARBIDE
y Side milling
Work
material

Copper alloys

Alloy tool steel
Hardened steel,Precipitation hardening stainless steel,

Ferritic, Precipitation hardening stainless steel,
AISI H13, AISI L6, AISI 431, AISI 420J2, AISI 630,
AISI 631
SQUARE
10
12
150
150
4800
4000
0.4
7700 0.5
0.45 7200 0.6
16
150
3000
0.5
6000 0.8
20
25
150
150
2400
1900
0.5
0.5
4800 1
3800 1.25
6
7.2
9.6
12
15
135
135
4300
3600
0.4
6900 0.5
0.45 6500 0.6
135
2700
0.5
5400 0.8
135
135
2100
1700
0.5
0.5
4200 1
3400 1.25
6
7.2
9.6
12
15
120
120
3800
3200
0.3
0.3
4600 0.5
3800 0.6
120
2400
0.4
3800 0.8
120
120
1900
1500
0.4
0.4
3000 1
2400 1.25
6
7.2
9.6
12
15
BALL
Dia
Revolution
per Min.
Revolution
per Min.
Revolution
per Min.
ae
Depth of
cut
DC:Dia.
Work
material
Austenitic stainless steel, Titanium alloy,


Ti-6Al-4V
Inconel718
RADIUS
ap
Dia
Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
Revolution
per Min.
40
40
1300
1100
0.2
0.2
1000 0.5
880 0.6
16
40
800
0.3
960 0.8
20
25
40
40
640
510
0.3
0.3
770 1
610 1.25
6
7.2
9.6
12
15
25
25
800
660
0.1
0.1
320
260
0.5
0.6
25
500
0.15
300
0.8
25
25
400
320
0.15
0.15
240
190
1
1.25
6
7.2
9.6
12
15
10
12
ae
Depth of
cut
ap
DC:Dia.
4) Reduce the feed by 1/2 for ramping process.
iMX-C4FD-C
J451
J467

CARBIDE
iMX-C4FV
Corner radius head for high efficiency machining, 4 flute, Irregular helix
SQUARE

Gray Cast Iron
Pre-hardened steel,
Alloy tool steel
AISI 1045, AISI 4140, AISI No 45 B
AISI P21, AISI P20, SKD, SKT
AISI H13, AISI L6
Work material
BALL
Corner R Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Dia.
Revolution
per Min.
Revolution
per Min.
Revolution
per Min.
DC (mm) RE (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) ae (mm)
10
12
2
2
90
90
2900 0.25 2900

2400 0.25 2400
1.2
1.8
4.5
6
75
75
2400 0.21 2000 1

2000 0.21 1700 1.4
4.5
6
60
60
1900 0.22 1700

1600 0.22 1400
0.7
0.9
4.5
6
16
90
1800 0.25 1800
1.8
7.5
75
1500 0.2
1200 1.4
7.5
60
1200 0.22 1100
0.9
7.5
20
25
3
4
90
90
1400 0.25 1400

1100 0.25 1100
1.8
2.4
9
11.5
75
75
1200 0.2
950 0.2
1000 1.4
750 1.8
9
11.5
60
60
0.9
1.2
9
11.5
950 0.22
750 0.22
850
650
ae
Depth of cut
RADIUS
ap
DC:Dia.
y High speed milling

Gray Cast Iron
Pre-hardened steel,
Alloy tool steel
AISI 1045, AISI 4140, AISI No 45 B
AISI P21, AISI P20, SKD, SKT
AISI H13, AISI L6
Work material
Dia.
Corner R Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
Revolution
per Min.
Revolution
per Min.
DC (mm) RE (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) ae (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) ae (mm)
J468
10
12
2
2
150 4800 0.51 9800

150 4000 0.56 9000
0.6
0.9
4.5
6
125 4000 0.43 6900 0.46

125 3300 0.48 6400 0.7
4.5
6
16
20
25
3
3
4
150 3000 0.6

150 2400 0.6
150 1900 0.6
0.9
0.9
1.2
7.5
9
11.5
125 2500 0.53 5300 0.7

125 2000 0.37 3000 0.7
125 1600 0.39 2500 0.9
7.5
9
11.5
7200
5800
4500
100 3200 0.43 5500 0.36

100 2700 0.47 5100 0.45
4.5
6
100 2000 0.54 4300 0.45 7.5

100 1600 0.39 2500 0.45 9
100 1300 0.39 2000 0.6 11.5
ae
Depth of cut
ap
DC:Dia.
iMX-C4FV
J452
iMX-S3A/iMX-C3A
Square/Corner radius head, 3 flute, For aluminium alloy
CARBIDE

Aluminium alloy
Work
material
SQUARE
y Slotting
Aluminium alloy
Work
material
A6061, A7075
Dia. Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min. Drilled Depth
DC (mm) (m/min)
(mm/t.) (mm/min) ap (mm) ae (mm)
(min-1)
A6061, A7075
Dia. Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut
Revolution
per Min. Drilled Depth
DC (mm)
(m/min)
(mm/t.)
(min-1)
(mm/min)
ap (mm)
10
12
500
500
16000
13000
0.117
0.118
5600
4600
8
9.6
3
3.6
10
12
500
500
16000
13000
0.068
0.072
3300
2800
16
500
10000
0.153
4600
12.8
4.8
16
500
10000
0.093
2800
20
25
500
500
8000
6000
0.175
0.211
4200
3800
16
20
6
7.5
20
25
500
500
8000
6000
0.108
0.127
2600
2300
10
12.5
5
6
BALL
y Side milling
ae
Depth of
cut
ap
ap
DC:Dia.
DC:Dia.
RADIUS
Depth of
cut
y Plunging
Aluminium alloy
Work
material
A6061, A7075
10
12
300
300
9600
8000
0.1
0.1
960
800
5
6
2.5
2.5
16
20
25
300
300
300
6000
4800
3800
0.1
0.1
0.1
600
480
380
8
10
12.5
2.5
2.5
2.5
Depth of
cut
Dia. Cutting Speed Main Spindle Feed per Table Feed Depth of Cut
Step
Revolution Revolution per Min. Drilled Depth
DC (mm) (m/min)
(min-1)
(mm/rev) (mm/min) ap (mm) ap2 (mm)
ap
DC:Dia.
1) The use of water-soluble coolant is recommended.

iMX-S3A
iMX-C3A
J442
J453
J469

CARBIDE
iMX-S3A/iMX-C3A
Square/Corner radius head, 3 flute, For aluminium alloy, Offset type
SQUARE

y Side milling
Aluminium alloy
Work material
A6061, A7075
RADIUS
BALL
L/D
<3
Dia. Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
DC (mm) (m/min)
(mm/t.) (mm/min) ap (mm) ae (mm)
(min-1)
12
14
18
22
28
500
500
500
500
500
13000
11000
8800
7200
5700
0.117
0.118
0.153
0.175
0.211
4600
3900
4000
3800
3600
9.6
11.2
14.4
17.6
22.4
2.4
2.8
3.6
4.4
5.6
12
14
300
300
8000
6800
0.09
0.09
2200
1800
9.6
11.2
1.0
1.1
18
300
5300
0.12
1900
14.4
1.4
22
28
300
300
4300
3400
0.14
0.17
1800
1700
17.6
22.4
1.8
2.2
12
14
18
22
28
200
200
200
200
200
5300
4500
3500
2900
2300
0.08
0.08
0.11
0.12
0.15
1300
1100
1200
1000
1000
9.6
11.2
14.4
17.6
22.4
0.5
0.6
0.7
0.9
1.1
ae
Depth of cut
ap
DC:Dia.
J470
1) The use of water-soluble coolant is recommended.

iMX-S3A
iMX-C3A
J442
J453
iMX-C6HV/C10HV/C12HV
Corner radius head, Multi-flute, Irregular helix
CARBIDE
Work
material

Alloy tool steel

Ferritic, Precipitation hardening stainless steel, Titanium alloy Cobalt chromium alloy

SQUARE
y Side milling
AISI 630, AISI 631
10
12
200
200
6400 0.07 2700

5300 0.085 2700
10
12
1
1.2
150
150
4800 0.07 2000

4000 0.085 2000
10
12
1
1.2
100
100
3200 0.07 1300

2700 0.085 1400
10
12
1
1.2
16
200
4000 0.07
2800
16
0.64
150
3000 0.088 2600
16
0.64
100
2000 0.07
1400
16
0.64
20
25
200
200
3200 0.08
2500 0.08
3100
2400
20
25
0.8
1
150
150
2400 0.1
1900 0.1
20
25
0.8
1
100
100
1600 0.08
1300 0.08
1500
1200
20
25
0.8
1
2900
2300
BALL
Dia
Revolution
per Min.
Revolution
per Min.
Revolution
per Min.
ae
Depth of
cut
DC:Dia.

Work
material
RADIUS
ap
Inconel718
10
12
40
40
1300 0.033 260

1100 0.035 230
10
12
0.5
0.6
16
40
800 0.038 300
16
0.64
20
25
40
40
640 0.04
510 0.04
20
25
0.8
1
310
240
ae
Depth of
cut
ap
DC:Dia.
3) The irregular helix flute end mill has a large effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece
installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut.
4) If the machining radius at the corner is the same as the tool radius when using the head with more than 10 flutes, please set the depth of cut and feed rate to half of the
above.
iMX-C6HV
iMX-C10HV
iMX-C12HV
J450
J450
J450
Dia
Cutting Speed Main Spindle Feed per Tooth Table Feed Depth of Cut Cutting Width
Revolution
per Min.
DC (mm) (m/min) (min-1) (mm/t.) (mm/min) ap (mm) ae (mm)
J471

CARBIDE
iMX-B4HV/iMX-B4HV-E
Ball nose head, 4 flute, Irregular helix (With/Without coolant hole)
BALL
SQUARE

y Shoulder milling
Work
material
Carbon steel, Alloy steel, Mild Steel,

Pre-hardened steel, Copper, Copper alloys

Cobalt chromium alloy, Titanium alloy
AISI 304, AISI 316, AISI 431, AISI 420J2,
AISI 1045, AISI 4140, AISI 4340, ASTM A36, AISI 1010, AISI P21,
AISI P20
Inclination
% <15
% <15
%>15
%>15
Depth of cut Pick Feed
angle
ap
pf
ap
pf
Radi
u
s
of
Bal
l
Nose
Main
Spindle
Table
Feed
Main
Spindle
Table
Feed
Main
Spindle
Table
Feed
Main
Spindle
Dia
Cutting Speed
Feed per Tooth
Cutting Speed
Feed per Tooth
Cutting Speed
Feed per Tooth
Cutting Speed
Feed per Tooth Table Feed
PRFRAD
Revolution
per Min.
Revolution
per Min. (mm) (mm)
Revolution
per Min.
Revolution
per Min. (mm) (mm)
DC (mm) (mm) (m/min) (min-1) (mm/t.) (mm/min) (m/min) (min-1) (mm/t.) (mm/min)
(m/min) (min-1) (mm/t.) (mm/min) (m/min) (min-1) (mm/t.) (mm/min)
10
12
5
6
300 9600 0.106 4100 200 6400 0.07 1800 1

300 8000 0.125 4000 200 5300 0.085 1800 1.2
2.5
3
225 7200 0.105 3000 150 4800 0.067 1300 1

225 6000 0.125 3000 150 4000 0.08 1300 1.2
16
300 6000 0.134 3200 200 4000 0.088 1400 1.6
225 4500 0.14 2500 150 3000 0.09 1100 1.6
5
6
225 3600 0.16 2300 150 2400 0.105 1000 2

225 2900 0.16 1900 150 1900 0.105 800 2.5
5
6
300 4800 0.156 3000 200 3200 0.1

20 10
25 12.5 300 3800 0.16 2400 200 2500 0.1
1300 2
1000 2.5
2.5
3
RADIUS
pf
Depth of
cut
ap
DC:Dia.

Work
material
Inconel718
Inclination
% <15
%>15
angle
ap
pf
Radi
u
s
of
Bal
l
Nose
Main
Spindle
Table
Feed
Main
Spindle
Table
Feed
Dia
Cutting Speed
Feed per Tooth
Cutting Speed
Feed per Tooth
PRFRAD
Revolution
per Min.
Revolution
per Min. (mm) (mm)
10
12
5
6
60 1900 0.055 420

60 1600 0.055 350
40 1300 0.035 180

40 1100 0.035 150
0.5
0.6
1
1.2
16
60 1200 0.062 300
40
800 0.04
130
0.8
1.6
60 1000 0.062 250

60
760 0.062 190
40
40
640 0.04
510 0.04
100
80
1
1.2
2
2.5
20 10
25 12.5
pf
Depth of
cut
ap
DC:Dia.
J472
iMX-B4HV
iMX-B4HV-E
J444
J445
iMX-B6HV
Ball nose head, 6 flute, Irregular curve
CARBIDE

Carbon steel, Alloy steel, Mild Steel,
Pre-hardened steel

Cobalt chromium alloy, Titanium alloy
AISI 304, AISI 316, AISI 431, AISI 420J2,
AISI 1045, AISI 4140, AISI 4340, ASTM A36, AISI 1010, AISI P21,
AISI P20
Inclination
% <15
% <15
%>15
%>15
angle
ap
pf
ap
pf
Dia Radius of Ball Nose Cutting Speed Main Spindle Feed per Tooth Table Feed Cutting Speed Main Spindle Feed per Tooth Table Feed
Cutting Speed Main Spindle Feed per Tooth Table Feed Cutting Speed Main Spindle Feed per Tooth Table Feed
PRFRAD
Revolution
per Min.
Revolution
per Min. (mm) (mm)
Revolution
per Min.
Revolution
per Min. (mm) (mm)
(m/min) (min-1) (mm/t.) (mm/min) (m/min) (min-1) (mm/t.) (mm/min)
10
12
5
6
300 9600 0.106 6100 200 6400 0.07 2700 0.5

300 8000 0.125 6000 200 5300 0.085 2700 0.6
2
2.4
225 7200 0.105 4500 150 4800 0.067 1900 0.5

225 6000 0.125 4500 150 4000 0.08 1900 0.6
2
2.4
16
300 6000 0.134 4800 200 4000 0.088 2100 0.8
3.2
225 4500 0.14 3700 150 3000 0.09 1600 0.8
3.2
4
5
225 3600 0.16 3400 150 2400 0.105 1500 1

225 2900 0.16 2800 150 1900 0.105 1200 1.2
4
5
300 4800 0.156 4500 200 3200 0.1

20 10
25 12.5 300 3800 0.16 3600 200 2500 0.1
1900 1
1500 1.2
BALL
Work
material
SQUARE
y Shoulder milling
ap
DC:Dia.
RADIUS
pf
Depth of
cut

Work
material
Inconel718
10
12
5
6
60 1900 0.055 630

60 1600 0.055 520
40 1300 0.035 270

40 1100 0.035 220
0.5
0.6
1
1.2
16
60 1200 0.062 450
40
800 0.04
190
0.8
1.6
60 1000 0.062 370

60
760 0.062 300
40
40
640 0.04
510 0.04
150
120
1
1.2
2
2.5
20 10
25 12.5
Inclination
% <15
%>15
angle
ap
pf
Radi
u
s
of
Bal
l
Nose
Main
Spindle
Table
Feed
Main
Spindle
Table
Feed
Dia
Cutting Speed
Feed per Tooth
Cutting Speed
Feed per Tooth
PRFRAD
Revolution
per Min.
Revolution
per Min. (mm) (mm)
pf
Depth of
cut
ap
DC:Dia.
iMX-B6HV
J446
J473

OF ROTATING TOOL INSERTS
a How the section of milling inserts is organized
a How the standards for milling inserts are organized
zOrganized according to cutter type.

xCutters are arranged in alphabetical order.
zClassified into milling inserts, wiper inserts and drilling

inserts.
xArranged in order of alphabet of order number.
GRADE APPLICATION RECOMMENDED FOR

EACH WORK MATERIAL
cutting conditions suitable for each work materials
are shown as a general guide to select grade.
:Stable Cutting
:General Cutting
:Unstable Cutting
PAGE TITLE BY TOOL APPLICATION

INSERT NUMBER
INSERT TOLERANCE HONING
INSERT GRADE
PAGE TITLE
PRODUCT SECTION
ROTATING INSERTS
CLASSIFICATION
Page
Cutter Type
AHX640W
Order Number
Page
Cutter Type
APX3000
NNMU200608ZEN-MK
LDCN190412L
K026
Work
Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Coated
AOMT123610PEER-M
AOMT123616PEER-M
K026
12
6.6
3.6
1.8 0.2
AOGT123604PEFR-GM G
12
6.6
3.6
1.6 0.4
AOGT123608PEFR-GM G
12
6.6
3.6
1.2 0.8
APX3000 AOMT123604PEER-H M
a a a a a a a a
12
6.6
3.6
1.6 0.4
AOMT123608PEER-H M
a a a a a a a a
12
6.6
3.6
1.2 0.8
AOMT123616PEER-H M
a a a a a a a a
12
6.6
3.6
0.4 1.6
APX3000 AOMT123602PEER-M M
a a a a a a a
12
6.6
3.6
1.8 0.2
AOMT123604PEER-M M
a a a a a a a
12
6.6
3.6
1.6 0.4
AOMT123608PEER-M M
a a a a a a a
12
6.6
3.6
1.2 0.8
AOMT123610PEER-M M
a a a a a a a
12
6.6
3.6
1.0 1.0
^L046
AOMT123624PEER-M
WNEU2006ZEN7C-WK
K043
Order Number
K022
AOMT123620PEER-M
GDCN2004PDR
Dimensions (mm)
Carbide
APX3000 AOGT123602PEFR-GM G
Shape
AOMT123612PEER-M
: Unstable Cutting
Honing :
E : Round F : Sharp
AOMT123608PEER-M
NNMU200608ZEN-HK
W1
BS
RE
Geometry
AOMT123630PEER-M
K044
AOMT123632PEER-M
AJX
AHX640S
Page
AOMT123604PEER-M
K044
AF10000
Order Number
AOMT123602PEER-M
Class
Order Number
LDCN190412R
Honing
AF5000
MC5020
MP6120
MP6130
MP7130
MP9120
MP9130
VP15TF
VP20RT
UP20M
HTi10
TF15
Cutter Type
NNMU200708ZEN-MP
JOMW06T215ZZSR-FT
AOMT123604PEER-H
JOMW080320ZZSR-FT
AOMT123608PEER-H
JDMW09T320ZDSR-FT K024
AOMT123616PEER-H
^L046
K022
JDMW120420ZDSR-FT
NNMU200712ZER-MM
AOMT184808PEER-H
JOMT080320ZZSR-JM
AOMT184816PEER-H
K043
AOMT123612PEER-M M
a a a a a a a
12
6.6
3.6
0.8 1.2
AOMT184840PEER-H
AOMT123616PEER-M M
a a a a a a a
12
6.6
3.6
0.4 1.6
JDMT140520ZDSR-JM
AOMT184850PEER-H
AOMT123620PEER-M M
a a a a a a a
12
6.6
3.6
0.4 2.0
JDMT120420ZDSR-ST
AOMT184864PEER-H
AOMT123624PEER-M M
a a a a a a a
12
6.6
3.6
0.4 2.4
AOMT123630PEER-M M
a a a a a a a
12
6.6
3.6
0.4 3.0
JDMT140520ZDSR-ST
AOMT184804PEER-M
AOMT123632PEER-M M
a a a a a a a
12
6.6
3.6
a a a a a a a a
18
4.8
1.8 0.4
AOMT184808PEER-H M
a a a a a a a a
18
4.8
1.4 0.8
AOMT184816PEER-H M
a a a a a a a a
18
4.8
0.4 1.6
AOMT184832PEER-H M
a a
18
4.8
0.4 3.2
AOMT184840PEER-H M
a a
18
4.8
0.4 4.0
AOMT184850PEER-H M
a a
18
4.8
AOMT184864PEER-H M
a a
18
4.8
a a a a a a a
18
4.8
1.8 0.4
AOMT184808PEER-M M
a a a a a a a
18
4.8
1.4 0.8
AOMT184810PEER-M M
a a a
18
4.8
1.0 1.0
AOMT184812PEER-M M
a a a
18
4.8
0.8 1.2
AOMT184816PEER-M M
a a a a a a a
18
4.8
AOMT184820PEER-M M
18
4.8
0.4 2.0
BAP300 APGT1135PDFR-G2 G
11
6.35 3.5
1.2 0.8
K024
AOMT184808PEER-M
AOMT184810PEER-M
NNMU200608ZEN-MK
JDMT140523ZDER-JL
AOX445
AOMT184820PEER-M
QOMT0830R-M2
^L052
QOMT1035R-M2
SL-ONEN120404ASN
K026
K045
QOMT1342R-M2
QOMT1651R-M2
QOMT1856R-M2
APX3000
WNEU2006ZEN7C-WK
K043
AOGT123608PEFR-GM
K027
QOMT2062R-M2
AOGT123602PEFR-GM
AOGT123604PEFR-GM
^L052
AOMT184816PEER-M
K024
AQX
NNMU200608ZEN-HK
K022
AOMT184812PEER-M
JDMT09T323ZDER-JL
JDMT120423ZDER-JL
K026
^L046
AOMT184832PEER-H K022
K024
JDMT120420ZDSR-JM
WNEU2007ZEN7C-WP
AOMT184804PEER-H
JOMT06T215ZZSR-JM
JDMT09T320ZDSR-JM
K026
ROTATING INSERTS
APX4000
JDMW140520ZDSR-FT
ROTATING INSERTS
K026
K022
a a a
a
0.4 3.2
5.0
6.35
0.4 1.6
QOMT2576R-M2
K022
K014

INSERT NUMBER
INSERT
GEOMETRY
CUTTER TYPE
CONT. IN NEXT COLUMN
indicates that the description of a
specific cutter is continued in the
next column.
STOCK STATUS
PHOTO OF INSERT
PAGE TO GO TO

indicates the reference pages for

detailed standards of specific inserts.

zinsert number and grade.
K000
INSERT DIMENSIONS
MILLING TOOLS
INSERT STANDARDS
CBN&PCD INSERT STANDARDS
INSERT GRADES
IDENTIFICATION ............................................... K002
GRADES FOR MILLING .................................... K004
MILLING APPLICATION RANGE ...................... K005
COATED CARBIDE(CVD and PVD)....................... K008
CERMET ............................................................ K010
CEMENTED CARBIDE ...................................... K011
CBN(SINTERED CBN) ............................................ K012
PCD(SINTERED DIAMOND) ..................................... K013
CLASSIFICATION.............................................. K014
STANDARD MILLING INSERTS
ROTATING INSERTS ..................................... K022
WIPER INSERTS............................................ K042
CBN AND PCD ............................................... K044
CBN AND PCD WITH WIPER ........................ K047
DRILLING INSERTS ...................................... K048
K001
IDENTIFICATION
Symbol
Insert Shape
Heptagonal
Symbol
Octagonal
Square
15
Triangular
20
Rhombic80
25
Rhombic86
30
Parallelogram85
Round
11
Special Design
Wiper
z Insert Shape
Normal Clearance AN
x Normal Clearance
IC
IC
Symbol
Tolerance of
Nose Height
M (mm)
Tolerance of
Inscribed Circle
IC (mm)
Tolerance of
Thickness
S (mm)
e0.005
e0.025
e0.025
e0.013
e0.025
e0.025
e0.025
e0.025
e0.025
e0.025
e0.025
e0.13
*
*
N*
e0.013
e0.05 e0.15
e0.025
e0.08 e0.18
e0.05 e0.15
e0.13
e0.08 e0.18
e0.05 e0.15
e0.025
K002
v Fixing and/or for Chip Breaker

M
c Tolerance Class
M
ROTATING INSERTS
* mark is sintered.
Symbol
Hole
Hole
Chip
Configuration Breaker
No
One Countersink
With Hole (40 60)
Single
Sided
With Hole
Figure
Cylindrical Hole
N
R
X
Without
Hole
Without
Hole
No
No
Single
Sided
One Countersink
(70 90)
Special Design
Honing
Symbol
F
Sharp
Diameter of
Inscribed
Circle
06
11
6.35
08
07
13
7.94
09
09
16
9.525
10
10.00
12
12.00
Round
06
Chamfer
Insert
Thickness
Symbol
12
12
22
12.70
03
3.18
16
15
27
15.875
T3
3.97
20.00
04
4.76
20
b Insert Size
Chamfer
(Strong Cutting Edge Type)
. Cutting Edge Condition
03
m Wiper insert cutting angle
Chamfer+Hone
n Insert Thickness
12
(mm)
, Clearance of Wiper Insert
KRINS
AS
1 - JS
11
u
12
u
12 Chip Breaker
u
/ Hand Tool Holder

Symbol
Hand Tool Holder
Symbol
Name
Left Hand Tool Holder
FT
FT Breaker
For Both Right and

Left Hand Tool Holder
HS
HS Breaker
Right Hand Tool Holder
JH
JH Breaker
Symbol
Wiper insert cutting angle
Symbol
Clearance Angle
45
15
JM
JM Breaker
75
20
JP
JP Breaker
90
25
JS
JS Breaker
Other Angle
30
LS
LS Breaker
MM
MM Breaker
MS
MS Breaker
BS
11 Width of Wiper Insert

u
Symbol
Width of Wiper Insert
1.4
(1.94 only for TEKN)
ROTATING INSERTS
Symbol
K003
Hardened Materials
K004
S
H
N20
N30
S01
S10
S20
H01
H10
H20
MB730
N01
N10
S30
H30
MD230
MB730
MB710
UTi20T
Cemented
Carbide
MD220
MD205
UTi20T
HTi10
UTi20T
NX4545
NX2525
Cermet
HTi05T
NX2525
VP30RT
PVD
NX4545
VP30RT
MP7140
VP20RT
VP20RT
P40
UP20M
CVD
UP20M
MP6130
VP15TF
MP6120
F7030
FH7020
F7010
Coated Carbide
NX2525
VP20RT
VP15TF
MP7030
K30
MP9030
K01
MP7130
M40
MP9130
M30
TF15
K20
HTi10
K10
VP15TF
M20
LC15TF
M10
F7030
P30
VP15TF
N
P20
MP8010
K
M01
F7010
Steel
P10
MC5020
Stainless Steel
M
P01
VP15TF
Cast Iron
MP9120
Non-Ferrous Metal
ISO
MP8010
ROTATING INSERTS
GRADES FOR MILLING

a INDEXABLE INSERT GRADES FOR MILLING
CBN
PCD
(Sintered CBN) (Sintered Diamond)
MILLING APPLICATION RANGE

P
STEEL
STAINLESS STEEL
300
F7010
CVD Coated Carbide
400
PVD Coated Carbide
MP6120
VP15TF
200
MP6130
VP20RT
NX2525
100
NX4545
Cermet
VP15TF
200
MP7130
VP20RT
NX2525
100
NX4545
VP30RT
UTi20T
Cermet
Cemented Carbide
0.2
0.4
0.6
0.8
K
400
0.2
NON-FERROUS METAL
Sintered Diamond
MD220
300
PVD Coated Carbide
MC5020
200
CVD Coated Carbide
VP15TF
VP20RT
100
NX2525
0.2
600
400
200
HTi10
UTi20T
Cermet
0.4
800
Sintered CBN
MP8010
0.3
Feed (mm/tooth)
CAST IRON
MB710
MB730
UTi20T
Cemented Carbide
0.1
Feed (mm/tooth)
MP7140
VP30RT
ROTATING INSERTS
300
PVD Coated Carbide
CVD Coated Carbide

F7030
F7010
FH7020
F7030
Cemented Carbide
HTi10
TF15
Cemented Carbide
0.4
Feed (mm/tooth)
0.6
0.8
0.1
0.2
0.3
0.4
Feed (mm/tooth)
K005
MILLING APPLICATION RANGE

a Recommendation of the insert grade based on cutting speed and conditions for each workpiece.
P STEEL (Medium to Rough Cutting)
M STAINLESS STEEL
300
300
MP6120
MP6130
200
VP30RT
400
200
MP7130
MP7140
100
100
Cutting Conditions
Cutting Conditions
K CAST IRON (CBN)
K CAST IRON
500
1500
MP8010
300
200
MC5020
MB730
1000
500
MB710
100
Cutting Conditions
K006
VP15TF
ROTATING INSERTS
400
Cutting Conditions
Stable Cutting
Plane Cutting
Pre-Machined
General Cutting
Unstable Cutting
N NON-FERROUS METAL (PCD)
N NON-FERROUS METAL
1500
300
HTi10
TF15
200
400

1000
MD220
500
100
Cutting Conditions
Cutting Conditions
S HEAT RESISTANT ALLOY, TITANIUM ALLOY
75
50
MP9120
MP9130
25
ROTATING INSERTS
100
Cutting Conditions
K007
COATED CARBIDE
(CVD&PVD)
<CVD>
a Special tough fibrous structure improves wear and fracture resistance.
a It covers a wide application range and reduces
the number of tools required.

<PVD>
a PVD coating prolongs tool life when compared to cemented carbide
under the same cutting conditions.
a Coating of tools with sharp edges is possible without softening or changing
the quality of the subsrate.
SELECTION STANDARD
a MILLING
150 (100 200)
LC15TF
1000 (200 3000)
MP9120
30 (20 40)
S01
VP15TF
30 (20 40)
S10
MP9130
40 (25 60)
S20
MP9030
40 (25 60)
S30
MP8010
80 (50 120)
VP15TF
80 (50 120)
K30
VP20RT
K20
H
Hardened
Materials
H01
H10
H20
MP9030
Ti Alloy
MP9130
Heat Resistant
Alloy
MP9120
N30
S
VP15TF
N20
VP15TF
Aluminium Alloy
LC15TF
N10
MP8010
ROTATING INSERTS
K10
H30
K008
VP30RT
VP15TF
Cast Iron
K01
VP30RT
180 (100 250)
M40
MP7140
MC5020
M30
VP20RT
150 (100 200)

150 (100 200)
VP20RT
MP7140
VP15TF
M20
UP20M
M10
MP7130
200 (150 250)

150 (100 200)
150 (100 200)
UP20M
P40
F7030
MP7030
MP7030
VP15TF
MP6130
P30
150 (100 200)
MP7130
MP6130
VP15TF
P20
150 (100 200)
VP15TF
MP6120
MP6120
P10
150 (100 200)
F7030
200 (150 250)
VP15TF
Stainless Steel
F7030
Application Range
F7030
ISO
FH7020
Steel
Recommended Cutting Speed

(m/min)
MP8010
Recommended Grade
MC5020
Work Material
Substrate
Coating Layer
Substrate
Grade
Hardness
(HRA)
T.R.S
(GPa)
Composition
Thickness
MC5020
91.0
2.2
TiCN-AI2O3-Ti Compound
FH7020
88.8
2.8
TiCN-AI2O3-Ti Compound
Coating Layer
Grade
Hardness
(HRA)
T.R.S
(GPa)
Composition
Thickness
Thick
MP8010
93.5
2.3
(Al,Ti,Si)N
Thin
Thick
MP9120
91.5
2.5
(Al,Ti,Cr)N
Thin
Thin
MP9030
90.5
2.5
(Al,Ti)N-Ti Compound
Thin
Thin
MP9130
90.5
2.7
(Al,Ti,Cr)N
Thin
Thin
F7030
88.8
2.8
TiCN-Al2O3-TiN
MP6120
91.5
2.5
(Al,Ti,Cr)N
MP6130
90.5
2.5
(Al,Ti,Cr)N
Thin
VP15TF
91.5
2.5
(Al,Ti)N
MP7030
90.5
2.5
(Al,Ti)N-Ti Compound
Thin
VP20RT
90.5
2.5
(Al,Ti)N
Thin
MP7130
90.5
2.5
(Al,Ti,Cr)N
Thin
VP30RT
88.8
2.8
(Al,Ti)N
Thin
MP7140
88.8
2.8
(Al,Ti,Cr)N
Thin
UP20M
90.5
2.0
TiN
Thin
*1GPa=102kg/mm
For machining of stainless steel
MP7030
Heat-resistant Alloy, Cutting For Titanium Alloy
MP9130
Multi-layer
coating
Special substrate
ROTATING INSERTS
MP7030 has a multi-layer coating based

on newly developed Ti-compound. It
provides superior wear and fracture
resistance in stainless steel machining.
A special tough cemented carbide
substrate gives excellent performance
in machining of difficult-to-cut materials
such as stainless steel.
An enhanced super fine cemented carbide

substrate has increased toughness while
maintaining hardness.
The Al-Ti-Cr-N accumulating coating
ensures optimum heat and wear
resistance. The combination of these
properties gives excellent fracture
resistance and welding resistance
because of low coefficient of friction when
machining titanium alloy.
K009
CERMET
a NX2525 for high speed milling.
a NX4545 for general milling.
SELECTION STANDARD
Recommended Grade

(m/min)
NX2525
250
(150 350)
ISO
Application Range
P10
M10
P20
M20
Steel
150
(120 180)
NX4545
P30
M30
M
K
NX4545
Work Material
NX2525
a MILLING
200
(150 300)
NX2525
Cast Iron
K10
K20
NX2525
K01
(Note) In case of wet cutting, please use coated carbide VP15TF for steel cutting and coated carbide MC5020 for cast iron cutting.
ROTATING INSERTS
K010
Grade
Hardness (HRA)
T.R.S. (GPa)
NX2525
92.2
2.0
NX4545
90.0
2.2
Thermal Conductivity Thermal Expansion

(W/mK)
(x10-6/K)
33
7.8
33
7.8
*1GPa=102kg/mm , 1W/m K=2.3910

2
-3
cal/cm sec r
CEMENTED CARBIDE
a Available grade series are UTi20T for steel and cast iron, and HTi10 for cast iron, non-ferrous metal and
non-metal.
SELECTION STANDARD
a MILLING
Work Material
Recommended Grade

(m/min)
ISO
Application Range
P10
120
(50 180)
P20
UTi20T
UTi20T
Steel
P30
M10
UTi20T
M20
HTi10
100
(50 150)
UTi20T
120
(50 180)
K10
Cast Iron
K20
HTi10
M30
K30
UTi20T
120
(50 180)
UTi20T
Stainless Steel
N10
400
(300 500)
N20
ROTATING INSERTS
N30
MAIN COMPONENT AND APPLICATION

Main
Component
ISO
P
K
Characteristics
Work Material

Stainless steel and Cast iron
iron, Non-Ferrous
High rigidity and wear resistance. Cast
metals and Non-metal
WC-TiC-TaC-Co Heat / Deformation resistance.
WC-Co
TF15
HTi10
TF15
Non-Ferrous Metal
HTi10
N01
ISO
Grade
M
N
K
N
Hardness Thermal Conductivity Thermal Expansion Young's Modulus

(W/mK)
(x10-6/K)
(GPa)
(HRA)
UTi20T
HTi05T
90.5
92.5
38
79
HTi10
92.0
91.5
TF15
T.R.S
(GPa)
5.5
4.5
520
600
2.0
1.5
79
4.6
630
2.0
71
5.3
580
2.5
1GPa=102kg/mm2, 1W/m K=2.3910-3cal/cm sec r
K011
CBN (SINTERED CBN)

a MB710 and MB730 for cast iron cutting.
a BC5030 for high speed machining of cast irons now available.
a Due to the combination of the BC5030 insert geometry and
the AOX allows the use of up to 16 corners per insert,

enabling cost effective high efficiency machining.
SELECTION STANDARD / RECOMMENDED CUTTING CONDITIONS

a FINISHING
Work Material
Grey Cast Iron
Structure
250
JIS FC250
Ferritic + Pearilitic
JIS FC300
Pearilitic
500
750
1000
MB710
1250
MB730
Feed Depth of
(mm/tooth) ( Cut ) Coolant
mm
0.3
0.5
Dry
a ROUGHING
Work Material
Structure
Grey Cast Iron JIS FC250
Pearilitic

250
500
1000
1500
BC5030
2000
Feed Depth of
(mm/tooth) ( Cut ) Coolant
mm
0.15
3.0
Dry
FEATURES AND BASE

Grade
Application
MB710
ROTATING INSERTS
MB730
BC5030
CBN
For General
TiC
General purpose grade with well balanced wear and fracture resistance.
Cutting
Al2O3
For High Speed Cutting Has the largest CBN content and therefore displays good thermal conductivity.
CBN (High Content)
For interrupted Cutting It is suitable for the high temperatures that are generated in high speed cutting.
Co Base Alloy
High CBN content and high thermal conductivity. The whole insert is composed
CBN
For high-speed machining at large depths of cut
of sintered CBN. This enables high speed, high efficiency machining at larger
High-speed interrupted machining at large depths of cut
AIN
depths of cut. The coated grade for easy recognition of used corners.
TiN
APPLICATION EXAMPLES
Tool
AOX445R10008D
Insert
SL-ONEN120404ASN (BC5030)
Machine
Machining Center
Tool
FC250
Cutting Condition
Component
JIS FC250
Cutting Condition
NF10000R0408D (MB730)
Workpiece
Workpiece

Feed per Tooth (mm/tooth)
Table Feed (mm/min)
Depth of Cut (mm)
Width of Cut (mm)
Hydraulic component
1800
0.1
1200
Depth of Cut (mm)
2.8
Width of Cut (mm)
70
Table Feed (mm/min)
3057
Coolant
Dry (Wet cutting at previous process)
0.1
Axial Runout (mm)
< 0.005mm
Result
Compared with competitor CBN grade

cutting, the normal wear surface is excellent
and a extendable life finishing is maintained.
Result
K012
Main Component Coating Layer
Features
10 times longer tool life and 4 times higher efficiency

than ceramics. Excellent machining with a surface
finish of Ra < 1.6m
4584
0.05
90
PCD (SINTERED DIAMOND)

a Suitable for non-ferrous metals cutting such as aluminium alloy.
a Suitable for extremely high speed finishing.
Micro-Structure of MD220
GRADE FEATURES
Grade
Features
Excellent in the balance between wear resistance and fracture resistance.

For a wide range of tooling applications.
MD220

Work Material
Aluminium Alloy
(Si <12%)
1000 6000
Aluminium Alloy
(Si >13%)
Grade
Depth of Cut (mm)
MD220
0.3
0.5
200 800
2.0
Revolution : 6000min-1
1.6
Rz=1.05m
1.2
0.8
Revolution : 20000min-1
0.4
0 0
Rz=1.42m
5000
10000
15000
20000
Workpiece : JIS A7075-T6
Insert : NP-GDCW1240PDFR2
Grade : MD220
Tool : V10000R0406D
Feed : 0.2mm/tooth
Width of Cut : 80mm
Dry Cutting
ROTATING INSERTS
Finished Surface Roughness (m)
CUTTING PERFORMANCE
Revolution Speed (min-1)
K013
CLASSIFICATION
Cutter Type
AF5000
Order Number
Page
Cutter Type
AHX640W
LDCN190412R
Order Number
Page
NNMU200608ZEN-MK
Cutter Type
Order Number
APX3000
AOMT123602PEER-M
LDCN190412L
AOMT123604PEER-M
K026
AOMT123608PEER-M
K044
AOMT123610PEER-M
AOMT123612PEER-M
NNMU200608ZEN-HK
AOMT123616PEER-M
K026
AF10000
K022
AOMT123620PEER-M
GDCN2004PDR
AOMT123624PEER-M
WNEU2006ZEN7C-WK
K043
AOMT123630PEER-M
K044
AOMT123632PEER-M
AJX
AHX640S
Page
NNMU200708ZEN-MP
JOMW06T215ZZSR-FT
AOMT123604PEER-H
JOMW080320ZZSR-FT
AOMT123608PEER-H
JDMW09T320ZDSR-FT K024
AOMT123616PEER-H
K022
JDMW120420ZDSR-FT
K026
NNMU200712ZER-MM
WNEU2007ZEN7C-WP
AOMT184808PEER-H
JOMT080320ZZSR-JM
AOMT184816PEER-H
K024
AOMT184832PEER-H
JDMT120420ZDSR-JM
AOMT184840PEER-H
JDMT140520ZDSR-JM
AOMT184850PEER-H
JDMT120420ZDSR-ST
AOMT184864PEER-H
JDMT140520ZDSR-ST
K043
AOMT184804PEER-H
JOMT06T215ZZSR-JM
JDMT09T320ZDSR-JM
K026
ROTATING INSERTS
APX4000
JDMW140520ZDSR-FT
AOMT184804PEER-M
K024
AOMT184808PEER-M
AOMT184810PEER-M
NNMU200608ZEN-MK
JDMT120423ZDER-JL
JDMT140523ZDER-JL
AOMT184816PEER-M
K024
AOMT184820PEER-M
AQX
AOX445
NNMU200608ZEN-HK
QOMT0830R-M2
QOMT1035R-M2
SL-ONEN120404ASN
K026
K045
QOMT1342R-M2
QOMT1651R-M2
QOMT1856R-M2
APX3000
WNEU2006ZEN7C-WK
K043
AOGT123608PEFR-GM
K014
K027
QOMT2062R-M2
AOGT123602PEFR-GM
AOGT123604PEFR-GM
K022
AOMT184812PEER-M
JDMT09T323ZDER-JL
K026
K022
K022
QOMT2576R-M2
Cutter Type
AQX
Order Number
Page
Cutter Type
ASX445
QOGT0830R-G1
Order Number
Page
SEET13T3AGEN-JL
QOGT1035R-G1
K030
K027
SEMT13T3AGSN-JM
XDGX175012PDFR-GL
XDGX175024PDFR-GL
QOGT2576R-G1
XDGX175030PDFR-GL
K030
RDMW0517M0E
RDMW0724M0E
XDGX175004PDFR-GL
XDGX175020PDFR-GL
QOGT2062R-G1
RDMW0620M0E
AXD4000
Page
XDGX175016PDFR-GL
QOGT1856R-G1
ARX
Order Number
XDGX175008PDFR-GL
QOGT1342R-G1
QOGT1651R-G1
Cutter Type
K039
XDGX175032PDFR-GL
XDGX175040PDFR-GL
K027
XDGX175050PDFR-GL
SEMT13T3AGSN-JH
SOET12T308PEER-JL
K030
K031
XDGX175004PDER-GM
XDGX175008PDER-GM
XDGX175012PDER-GM
SEMT13T3AGSN-FT
SOMT12T308PEER-JM
SOMT12T308PEEL-JM
XDGX175016PDER-GM
XDGX175020PDER-GM
K032
K030
XDGX175024PDER-GM
XDGX175030PDER-GM
SOMT12T308PEER-JH
K039
XDGX175032PDER-GM
K031
SEGT13T3AGFN-JP
XDGX175040PDER-GM
ROTATING INSERTS
ASX400
XDGX175050PDER-GM
K030
SOMT12T320PEER-FT
K032
XDGX175004PDFR-GM
WEEW13T3AGER8C
XDGX175008PDFR-GM
WEEW13T3AGTR8C
XDGX175012PDFR-GM
K042
SOGT12T308PEFR-JP
XDGX175020PDFR-GM
K031
WOEW12T308PEER8C
WOEW12T308PETR8C
K043
XDGX175016PDFR-GM
XDGX175024PDFR-GM
WEEW13T3AGFR3C
XDGX175030PDFR-GM
WEEW13T3AGTR3C
XDGX175032PDFR-GM
K047
K039
XDGX175040PDFR-GM
XDGX175050PDFR-GM
K015
CLASSIFICATION
Cutter Type
Order Number
AXD7000
XDGX227008PDFR-GL
BAE
Page
Order Number
BAP3500
XPGT13T3PDFR-G1
Page
BN425
DN
Order Number
XDGX227020PDFR-GL
XPGT13T3PDFR-G6
XDGX227030PDFR-GL K039
XPGT13T3PDFR-G75
SNK43B2S
XDGX227032PDFR-GL
XPGT13T3PDFR-G8
SNKF43B2S
XDGX227040PDFR-GL
XPGT13T3PDER-G1
SNMF43B2G
XDGX227050PDFR-GL
XPGT13T3PDER-G2
AEMW150304ER
XPGT13T3PDER-G6
SNC43B2S
BRP
RPMW08T2M0T
RPMW10T3M0E
APMT1604PDER-H1
RPMW10T3M0T
APMT1135PDER-H1
APMT1604PDER-H2
RPMW1204M0E
APMT1135PDER-H2
APMT1604PDER-H4
BAP400
SRM2
RPMW1606M0E
APMT1135PDER-H4
APMT1604PDER-H8
RPMW1606M0T
APMT1135PDER-H6
APMT1604PDER-M2
RPMT08T2M0E-JS
K023
APMT1135PDER-M0
APMT1135PDER-M1
APMT1135PDER-M2
K028
RPMW1204M0T
K023
APMT1604PDER-H6
APMT1135PDER-H3
K031
K041
XPGT13T3PDER-G8
AEMW19T308ER
K031
SNK43B2G
K041
XPGT13T3PDER-G75
K023
Page
SNC43B2G
XPGT13T3PDFR-G2
AEMW19T304ER
RPMT10T3M0E-JS
K023
K028
RPMT1204M0E-JS
K023
RPMT1606M0E-JS
BSP
APGT1604PDFR-G2
SPMB1204APT
K023
APGT1135PDFR-G2
ROTATING INSERTS
Cutter Type
XDGX227016PDFR-GL
AEMW150308ER
BAP300
SRM2
Cutter Type
K022
K033
BF407
QBF407
SFAN1203ZFFR2
SFAN1203ZFFL2
BAP300
Under-cut
Type
SFCN1203ZFFR2
ZRM0603R-M3
ZRM0603R-M4
K041
ZRM0603R-M5
BAP3500
K030
BXD4000
XDGT1550PDER-G04
SFCN1203ZFFL2
XDGT1550PDER-G08
SFCN1203ZFFR2
XDGT1550PDER-G12
K045
XDGT1550PDER-G16
XPMT13T3PDER-M1
XDGT1550PDER-G20
XPMT13T3PDER-M2
XDGT1550PDER-G30
XPMT13T3PDER-M6
XPMT13T3PDER-M75
XPMT13T3PDER-M8
XDGT1550PDER-G32
WFC42ZFER2
K047
K041
XDGT1550PDER-G40
XDGT1550PDER-G50
NP-WFC42ZFER2
K047
K016
K038
Cutter Type
Order Number
Page
BXD4000
XDGT1550PDFR-G04
Cutter Type
DCCC
BZC
Order Number
Page
FMSD
ZCMX09T308ER-B
XDGT1550PDFR-G08
Cutter Type
Page
SDEN1203AEN
SDKN1203AEN
K041
XDGT1550PDFR-G12
Order Number
SDKN1203AETN
K028
SDKN1504AETN
XDGT1550PDFR-G16
XDGT1550PDFR-G20 K038
E404
FE404
XDGT1550PDFR-G30
FP490
SEA42C10GR
SEA42C10GL
XDGT1550PDFR-G32
SPEN424A
K032
K028
XDGT1550PDFR-G40
ECMP
TAB
XDGT1550PDFR-GL04
MPMT090308
XDGT1550PDFR-GL08
MPMT120408
K038
FBP415
QBP415
CBJP
CBMP
TAB
FP590
MPMT070308
K032
K025
NF10000
QF10000
SPEN1203EEER1
GDCN2004PDFR3
SPEN1203EEEL1
JPMT060204-E
SPNN1203EEER1
K025
SPNN1203EEEL1
MPMT090308
NF10000
K034
SPMW120304
K044
NR10000
SPEN1203EETR1
SPMW090304
SPMW090308
NP-GDCN2004PDSR3
K033
K025
MPMT120408
K044
K033
SPER1203EEER-JS
CESP
CFSP
CGSP
SPEN535A
GDCN2004ZDTR1
K044
K045
SPMW120308
DCCC
BZC
MG200
WPC42EEER10C
CCMX083508EN-A
CCMX09T308EN-A
WPC42EEEL10C
K023
FF3000
CCMX09T308EN-B
K043
ZCMX09T308ER-A
K041
MGEEW1242PFTR
K025
K032
MG400
SPCG53Z
ZCMX083508ER-A
K025
MG300
SPCA53Z
K024
MGEEW1035PFTR
K032
ROTATING INSERTS
XDGT1550PDFR-G50
MGEEW1650PFTR
K025
K017
CLASSIFICATION
Cutter Type
MG245
Order Number
Page
Cutter Type
NSE300
SE300
MGEEW1035AFTR
Order Number
Page
K045
NSE400
SE400
MGEEW1242AFTR
K025
Order Number
Page
OCTACUT REMX1705SN
BOE
TECN1603PEFR1
K025
MG345
Cutter Type
K027
TECN2204PEFR1
REMX12T3EN-JS
TECN2204PEER1
REMX1705EN-JS
K027
TECN2204PETR1
TEEN2204PEFR1
MG445
PMF
TEEN2204PEER1
MGEEW1650AFTR
K025
TEEN2204PETR1
TPEW1303ZPER2
K037
K037
TEEN2204PESR1
TEKN2204PEER1
MVX
SOMX063005-UM
TEKN2204PESR1
SOMX073505-UM
TEKN2204PETR1
SOMX084005-UM
TEKN2204PETR
SOMX094506-UM
K048
SOMX115506-UM
TPEW1303ZPTR2
K046
TEER2204PEER-JS
PMR
K037
SOMX136008-UM
CPMT1205ZPEN-M3
SOMX166508-UM
CPMT1906ZPEN-M2
SOMX187008-UM
S300
ROTATING INSERTS
K045
SOMX073505-US
SPMW090304
SPMW090308
K048
SOMX084005-US
NSE300
SE300
SOMX094506-US
OCTACUT
OEMX12T3ETR1
BOE
TEEN1603PEFR1
OEMX12T3ESR1
TEEN1603PEER1
S400
K026
OEMX1705ESR1
K036
TEEN1603PETR1
TEEN1603PESR1
K024
CPMT1906ZPEN-M3
TECN2204PEFR1
SOMX063005-US
K034
SPMW120304
SPMW120308
K034
OEMX1705ETR1
OEMX12T3ETR1
TECN1603PEFR1W
TECN1603PEER1W
TECN1603PETR1W
K044
K037
TEER1603PEER-JS
K037
K018
CPMT1205ZPEN-M2
SPMN120304
SPMN120304T
SPMN120308
OEMX12T3EER1-JS
SPMN120312
OEMX1705EER1-JS
SPGN120304
OEMX1705ETR1-JS
K027
SPGN120308
SPGN120312
K033
Cutter Type
S500
Order Number
Page
Cutter Type
SE445
LSE445
SPMN150408
SPMN150412
Order Number
Cutter Type
SPX
SECN1203AFFR1
Order Number
Page
JPMX140412-JM
JPMX190412-JM
K033
SPGN150404
Page
K025
K045
SPGN150408
SE415
QSE415
WEC42AFTR5C
SEEN1203EFFR1
SEEN1203EFER1
JPMX190412-WH
K042
K029
SEEN1203EFTR1
JPMX140412-WH
K025
SEEN1203EFSR1
SE515
SEKN1203EFSR1
SEKN1203EFTR1
K026
SEEN1504EFER1
K029
SEKN1203EFTR
MPMX120412-JM
SECN1504EFTR1
SEEN1504EFSR1
SEEN1504EFTR1
SEER1203EFER-JS
K029
MPMX120412-WH
K026
SEKN1504EFSR1
SEKN1504EFTR1
K029
SPMX120408-JM
WEC53EFTR5C
K034
K042
SECN1203EFFR1
K045
SPMX120408-WH
SE545
K034
SEEN1504AFEN1
SEEN1504AFSN1
WEC42EFTR5C
SEKN1504AFSN1
K042
K029
SRBT10
SRBT12
SEKN1504AFTN1
SRBT16
SRBT20
SE445
LSE445
SRBT25
SEER1504AFEN-JS
SECN1203AFTN1
SEEN1203AFFN1
SRBT30
K029
SEEN1203AFEN1
K034
ROTATING INSERTS
SRB
SEEN1504AFTN1
WEC42EFER5C
SRBT32
SEEN1203AFTN1
K028
SEEN1203AFSN1
SRF
WEC53AFER5C
SEKN1203AFSN1
WEC53AFTR5C
K042
SRFT10
SRFT12
SEKN1203AFTN1
SRFT16
SEKN1203AFTN
SRFT20
SG20
SEER1203AFEN-JS
K029
SRFT25
RGEN2004M0EN
RGEN2004M0SN
K028
K034
SRFT30
SRFT32
K019
CLASSIFICATION
Cutter Type
SRM2
Order Number
Page
Cutter Type
STAW
SRM16C-M
Order Number
Page
Cutter Type
TAF
STAWKooooTG
Order Number
Page
GCMT040204-U1
SRM20C-M
SRM25C-M
K055
K035
K048
SRM30C-M
SRM32C-M
STAWNooooT
SRM16E-M
STAWNooooTH
GCMT040204-U2
K053
K048
SRM20E-M
SRM25E-M
K035
SUF
SRM30E-M
SUFT10R05
GPMT060204-U1
SRM32E-M
SUFT10R10
GPMT070204-U1
SRG16C
SUFT10R20
GPMT090304-U1
SRG20C
SUFT12R05
GPMT11T308-U1
SUFT12R10
GPMT140408-U1
SRG30C
SUFT12R20
GPMT060204-U2
SRG32C
SUFT12R30
GPMT070204-U2
SRG16E
SUFT16R05
GPMT090304-U2
SRG20E
SUFT16R10
GPMT11T308-U2
SUFT16R15
GPMT140408-U2
SRG30E
SUFT16R20
GPMT060204-U3
SRG32E
SUFT16R30
GPMT070204-U3
SRG40C
SUFT20R05
GPMT090304-U3
SRG25C
ROTATING INSERTS
SRG25E
SRM2 & 40
& 50
K035
K035
SUFT20R10
SRG50C
K035
SUFT20R15
SUFT20R20
K048
K048
GPMT11T308-U3
K036
GPMT140408-U3
TAW
TAWNHooooT
SUFT20R30
SRG40E
SRG50E
K048
K035
SUFT25R05
K049
SUFT25R10
SUFT25R20
SUFT25R30
APMT1135PDER-H2
APMT1604PDER-H2
K023
TAWKHooooTG
SUFT30R05
K051
SUFT30R10
SUFT30R20
SUFT30R30
APMT1135PDER-M2
APMT1604PDER-M2
K023
SUFT32R05
SUFT32R10
SUFT32R20
K020
TAWBHooooT
K050
TBE1
Order Number
Page
Cutter Type
VOX400
SPMT120408-A
Order Number
MPMW120408
V10000
11 Positive
VIPER
11 Positive
TPNX1605N
K044
K038
WSX445
XNMU160708R-MS
XNMU160712R-MS
XNMU160716R-MS
XNMU160724R-MS
TPMN160308
TPMN160312
SNGU140812ANFR-L
TPMN220408
SNGU140812ANER-L
TPMN220412
SNMU140812ANER-M
XNMU160732R-MS
SNMU140812ANER-R
XNMU160740R-MS
SNMU140812ANER-H
XNMU160708R-HS
WNGU1406ANEN8C-M
K031
K043
XNMU160708R-LS
K040
Corner Angle 0
11 Positive
TPEN1603PPR
TPEN2204PDR
XNMU190912R-MS
TPKN1603PPR
XNMU190916R-MS
TPKN2204PDR
XNMU190924R-MS
XNMU190932R-MS
K038
SNGU140812ANER-M
K040
K040
VFX6
K033
TPMN160304
TPMN220404
VFX5
K031
SPMN120408
SPMN120412
K043
K025
Page
SNMN120408
SNMN120412
WOEX1206PER5C
NP-GDCW1240PDFR2
Order Number
K032
MPMW070308
MPMW090308
Cutter Type
Negative
SONX1206PER
K034
TSMP
Page
K040
Corner Angle 15
11 Positive
K037
ROTATING INSERTS
Cutter Type
SPKN1203EDR
SPKN1504EDR
SPEN1203EDR
XNMU190940R-MS
K033
XNMU190950R-MS
XNMU190912R-HS
K040
XNMU190912R-LS
Corner Angle 45
20 Positive
SEKN1203AGTN
K030
K040
K021
ROTATING INSERTS
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round F : Sharp
Dimensions (mm)
12
6.6
3.6
1.8 0.2
AOGT123604PEFR-GM G
12
6.6
3.6
1.6 0.4
AOGT123608PEFR-GM G
12
6.6
3.6
1.2 0.8
^L046
W1
BS
Geometry
RE
L
W1
APX3000 AOGT123602PEFR-GM G
Order Number
MC5020
MP6120
MP6130
MP7130
MP9120
MP9130
VP15TF
VP20RT
UP20M
HTi10
TF15
Honing
Carbide
Class
Coated
Shape
: Unstable Cutting
BS
Work
Material
P
M
K
N
S
H
11
S
RE
a a a a a a a a
12
6.6
3.6
1.6 0.4
AOMT123608PEER-H M
a a a a a a a a
12
6.6
3.6
1.2 0.8
AOMT123616PEER-H M
a a a a a a a a
12
6.6
3.6
0.4 1.6
L
W1
^L046
BS
11
S
RE
1.8 0.2
AOMT123604PEER-M M
a a a a a a a
12
6.6
3.6
1.6 0.4
AOMT123608PEER-M M
a a a a a a a
12
6.6
3.6
1.2 0.8
AOMT123610PEER-M M
a a a a a a a
12
6.6
3.6
1.0 1.0
AOMT123612PEER-M M
a a a a a a a
12
6.6
3.6
0.8 1.2
AOMT123616PEER-M M
a a a a a a a
12
6.6
3.6
0.4 1.6
AOMT123620PEER-M M
a a a a a a a
12
6.6
3.6
0.4 2.0
AOMT123624PEER-M M
a a a a a a a
12
6.6
3.6
0.4 2.4
AOMT123630PEER-M M
a a a a a a a
12
6.6
3.6
0.4 3.0
AOMT123632PEER-M M
a a a a a a a
12
6.6
3.6
0.4 3.2
a a a a a a a a
18
4.8
1.8 0.4
AOMT184808PEER-H M
a a a a a a a a
18
4.8
1.4 0.8
AOMT184816PEER-H M
a a a a a a a a
18
4.8
0.4 1.6
AOMT184832PEER-H M
a a
18
4.8
0.4 3.2
AOMT184840PEER-H M
a a
18
4.8
0.4 4.0
AOMT184850PEER-H M
a a
18
4.8
5.0
a a
4.8
6.35
ROTATING INSERTS
^L052
AOMT184864PEER-H M
AOMT184808PEER-M M
18
a a a a a a a
18
4.8
1.8 0.4
a a a a a a a
18
4.8
1.4 0.8
AOMT184810PEER-M M
a a a
18
4.8
1.0 1.0
AOMT184812PEER-M M
a a a
18
4.8
0.8 1.2
AOMT184816PEER-M M
a a a a a a a
18
4.8
0.4 1.6
AOMT184820PEER-M M
18
4.8
0.4 2.0
11
6.35 3.5
1.2 0.8
^L052
a a a
a
L
W1
3.6
RE
11
S
L
15
W1
6.6
RE
L
15
W1
12
BS
a a a a a a a
BS
^L046
BS
RE
BS
W1
RE
85
K022

11
S
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round F : Sharp
Dimensions (mm)
Honing
BAE AEMW150304ER
a a
15.875 9.525 3.18
0.4
AEMW150308ER
a a
15.875 9.525 3.18
0.8
AEMW19T304ER
a a
19.05 12.7
3.97
0.4
AEMW19T308ER
a a
19.05 12.7
3.97
0.8
Order Number
F7030
VP15TF
UP20M
NX2525
NX4545
UTi20T
HTi10
Class

Shape
: Unstable Cutting
IC
W1
BS
RE
Geometry
RE
W1
Work
Material
P
M
K
N
S
H
85
16.5
9.525 4.76
1.4
20
S
0.8
BS
W1
RE
85
11
6.35
3.5
1.5
0.4
a a
11
6.35
3.5
1.2
0.8
APMT1135PDER-H3 M
11
6.35
3.5
0.8
1.2
APMT1135PDER-H4 M
11
6.35
3.5
0.4
1.6
APMT1135PDER-H6 M
BAP400 APMT1604PDER-H1 M
SRM2
^L128 APMT1604PDER-H2 M
a a
APMT1604PDER-H4 M
APMT1604PDER-H6 M
11
6.35
16.5
16.5
a a
3.5
0.4
2.4
9.525 4.76
1.7
0.4
9.525 4.76
1.4
0.8
16.5
9.525 4.76
0.4
1.6
16.5
9.525 4.76
0.4
2.4
APMT1604PDER-H8 M
16.5
9.525 4.76
0.4
3.2
BAP300 APMT1135PDER-M0 M
SRM2
^L128 APMT1135PDER-M1 M
11
6.35
3.5
1.8
0.2
11
6.35
3.5
1.5
0.4
APMT1135PDER-M2 M
a a
11
6.35
3.5
1.2
0.8
RE
RE
85
a a
16.5
9.525 4.76
1.4
11
S
RE
85
BAP400 APMT1604PDER-M2 M
SRM2
11
S
85
ROTATING INSERTS
a a
a a
BS
W1
a a
BS
W1
11
S
BS
W1
BAP300 APMT1135PDER-H1 M
SRM2
^L128 APMT1135PDER-H2 M
11
S
0.8
^L128
BS
W1
RE
85
DCCC CCMX083508EN-A M
CCMX09T308EN-A M
a a a
7.94
3.5
0.8
9.525
3.97
0.8
11
S
RE
RE
7
80
IC
K023
ROTATING INSERTS
Work
Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round S : Chamfer + Hone
Dimensions (mm)
DCCC CCMX09T308EN-B
F7030
FH7020
MP6120
MP6130
MP7130
MP7140
MP9120
MP9130
VP15TF
VP30RT
Honing
Order Number
Class
Coated
Shape
: Unstable Cutting
IC
9.525 3.97
Geometry
BS RE AN
0.8
7
RE
RE
AN
IC
80
12.7
5.56 1.4 0.8
CPMT1205ZPEN-M3 M
12.7
5.56 1.4 1.2
CPMT1906ZPEN-M2 M
19.05
6.35 1.4 0.8
CPMT1906ZPEN-M3 M
19.05
6.35 1.4 1.2
RE
BS
PMR CPMT1205ZPEN-M2 M
^L143
IC
80
AJX JOMW06T215ZZSR-FT M
a a a a a
a a
6.35
2.78 1.2 1.5 13
JOMW080320ZZSR-FT M
a a a a a
a a
3.18 1.4 2
13
JDMW09T320ZDSR-FT M
a a a a a
a a
9.525 3.97 1.8 2
15
JDMW120420ZDSR-FT M
a a a a a
a a
JDMW140520ZDSR-FT M
a a a a a
JDMT09T323ZDER-JL M
a a
JDMT120423ZDER-JL M
a a
12
4.76 2.5 2.3 15
JDMT140523ZDER-JL M
a a
14
5.56 2.8 2.3 15
^L084
AJX
ROTATING INSERTS
^L084
a a
12
4.76 2.5 2
15
14
5.56 2.8 2
15
IC
RE
AN
a a a a a
a a
6.35
2.78 1.2 1.5 13
JOMT080320ZZSR-JM M
a a a a a
a a
3.18 1.4 2
JDMT09T320ZDSR-JM M
a a a a a
a a
JDMT120420ZDSR-JM M
a a a a a
a a
9.525 3.97 1.8 2

12
4.76 2.5 2
IC
RE
15
15
JDMT140520ZDSR-JM M
a a a a a
a a
14
5.56 2.8 2
15
AJX JDMT120420ZDSR-ST M
a a a a a
a a
12
4.76 2.5 2
15
JDMT140520ZDSR-ST M
a a a a a
a a
14
5.56 2.8 2
15
AN
BS
IC
RE
RE
K024
AN
IC

13
BS
9.525 3.97 1.8 2.3 15
AJX JOMT06T215ZZSR-JM M
^L084
AN
BS
BS
^L084
Work
Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round T : Chamfer
Dimensions (mm)
UTi20T
HTi10
JPMT060204-E
VP15TF
VP20RT
UP20M
NX2525
Honing
CBJP
^L137
Order Number
Class

Shape
: Unstable Cutting
6.5
W1
IC
RE
7.94
2.38
0.4
Geometry
RE
RE
W1
TAB
11
L
86
This figure is for outer insert (E).
SPX
JPMX140412-JM
a a
14.3
12.7
4.83
1.2
JPMX190412-JM
a a
19.05
12.7
4.79
1.2
RE
W1
^L108
86
SPX
JPMX140412-WH
a a
14.3
12.7
4.76
1.2
JPMX190412-WH
a a
19.05
12.7
4.76
1.2
11
RE
W1
^L108
11
MGEEW1035AFTR
a a
a a
10
3.5
MGEEW1242AFTR
a a
a a
12
10.5
4.2
MGEEW1650AFTR
a a
a a
16
13
65
MGEEW1035PFTR
a a
a a
10
3.5
MGEEW1242PFTR
a a
a a
12
10.5
4.2
MGEEW1650PFTR
a a
16
13
W1
MG200
MG300
MG400
CBMP
^L137
ECMP
TAB
MPMT070308
MPMT090308
MPMT120408
7.94
3.18
0.8
9.525
3.18
0.8
4.76
0.8
12.7
20
65
RE
ROTATING INSERTS
MG245
MG345
MG445
W1
86
20
RE
11
86
TSMP
^L136
MPMW070308
7.94
3.18
0.8
MPMW090308
9.525
3.18
0.8
MPMW120408
4.76
0.8
12.7
IC
RE
RE
11
86
IC
K025
ROTATING INSERTS
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
SPX MPMX120412-JM
^L108
Dimensions (mm)
Cermet Carbide
F7030
MC5020
VP15TF
VP20RT
MP7030
NX4545
Honing
Order Number
Class
Coated
Shape
: Unstable Cutting
Honing :
E : Round S : Chamfer + Hone T : Chamfer
a a
UTi20T
Work
Material
P
M
K
N
S
H
IC
BS
RE
12.7
4.79
1.2
Geometry
RE
11
SPX
^L108
MPMX120412-WH
12.7
a a
4.76
IC
86
1.2
RE
11
86
AHX640S
^L026
AHX640S
ROTATING INSERTS
^L026
NNMU200708ZEN-MP M
NNMU200712ZER-MM M
AHX640S NNMU200608ZEN-MK M
^L026
20
20
20
a a a
8.0
8.0
6.55
IC
0.8
BS
IC
RE
BS
IC
RE
BS
IC
RE
BS
IC
RE
1.2
0.8
AHX640W
^L030
AHX640S NNMU200608ZEN-HK M
^L026
20
a a a
6.55
0.8
AHX640W
^L030
OEMX12T3ESR1
OEMX1705ETR1
OEMX1705ESR1
a
a
a
a
12.7
3.97
12.7
3.97
17
1.4
17
1.4
BS
OCTACUT OEMX12T3ETR1
^L094
20
IC
K026

Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round F : Sharp S : Chamfer + Hone T : Chamfer
Honing
OCTACUT
^L094
OEMX12T3EER1-JS
OEMX1705EER1-JS
OEMX1705ETR1-JS
Dimensions (mm)
Carbide
F7030
VP15TF
VP30RT
UP20M
MP8010
UTi20T
HTi10
Order Number
Class
Coated
Shape
: Unstable Cutting
W1
12.7
3.97
17
1.4
17
1.4
IC
Geometry
BS
BS
Work
Material
P
M
K
N
S
H
20
IC
ARX
^L098
QOGT1035R-G1
QOGT1342R-G1
QOGT1651R-G1
QOGT1856R-G1
QOGT2062R-G1
QOGT2576R-G1
QOMT0830R-M2
a a
8.4
QOMT1035R-M2
a a
10.6
QOMT1342R-M2
a a
13.1
8.7
QOMT1651R-M2
a a
16.5
QOMT1856R-M2
a a
QOMT2062R-M2
a a
QOMT2576R-M2
a a
RDMW0517M0E
RDMW0620M0E
RDMW0724M0E
8.4
5.5
10.6
3.5
13.1
8.7
4.2
16.5
18
11
5.1
12
5.6
20.4
13.6
6.2
25.8
17.2
7.6
5.5
3.5
4.2
11
5.1
18
12
5.6
20.4
13.6
6.2
25.8
17.2
7.6
1.70
1.99
2.38
R0.4
W1
R0.4
R0.8
R0.8
15
S0.025
IC0.025
OCTACUT
^L094
REMX1705SN
17.25
5.2
ROTATING INSERTS
AQX
^L076
*1
*1
*1
*1
*1
*1
*1
QOGT0830R-G1
W1
AQX
^L076
20
IC
OCTACUT
^L094
REMX12T3EN-JS
12.95
4.17
REMX1705EN-JS
17.25
5.2
20
IC
*1 Grade VP15TF is "E".
K027
ROTATING INSERTS
Work
Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
RGEN2004M0EN
RGEN2004M0SN
Order Number
a
a
Dimensions (mm)
Cermet Carbide
F7030
MC5020
VP15TF
UP20M
NX2525
NX4545
UTi20T
HTi10
Honing
SG20
^L033
Class
Coated
Shape
: Unstable Cutting
a a
IC
BS
RE
20
4.76
20
4.76
Geometry
30
BRP
^L102
BRP
^L102
ROTATING INSERTS
FMSD
RPMT08T2M0E-JS M
RPMT10T3M0E-JS M
RPMT1204M0E-JS M
RPMT1606M0E-JS M
RPMW08T2M0T
RPMW10T3M0E
RPMW10T3M0T
RPMW1204M0E
RPMW1204M0T
RPMW1606M0E
RPMW1606M0T
SDEN1203AEN
SDKN1203AEN
SDKN1203AETN
SDKN1504AETN
10
3.97
12
4.76
16
6.35
10
3.97
10
3.97
12
4.76
12
4.76
16
6.35
16
6.35
12.7
3.18
1.2
12.7
3.18
1.2
12.7
3.18
1.7
15.875
4.76
1.7
a a
a
a
[
2.78
a
a
2.78
a
a
IC
IC
IC
11
11
BS
45
15
S
IC
FE404
SEA42C10GR
12.7
3.18
2.4
E404
SEA42C10GL
12.7
3.18
2.4
^L152
BS
21
IC
SE445
K028
SECN1203AFTN1
SEEN1203AFFN1
SEEN1203AFEN1
SEEN1203AFTN1
SEEN1203AFSN1
SEKN1203AFSN1
SEKN1203AFTN1
SEKN1203AFTN

12.7
3.18
1.4
1.0
12.7
3.18
1.4
1.0
12.7
3.18
1.4
1.0
12.7
3.18
1.4
1.0
a a
12.7
3.18
1.4
1.0
12.7
3.18
1.4
12.7
3.18
1.4
12.7
3.18
1.7
1.0
a
a
a
a a
a
a
BS
RE
IC
45
20
S
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
Dimensions (mm)
SEEN1504AFTN1
SEEN1504AFSN1
a a
15.875
4.76
1.4
1.0
SEKN1504AFSN1
15.875
4.76
1.4
SEKN1504AFTN1
SE445 SEER1203AFEN-JS E
NX2525
NX4545
UTi20T
HTi10
SE545 SEEN1504AFEN1
Order Number
F7030
MC5020
VP15TF
Honing
Cermet Carbide
Class
Coated
Shape
: Unstable Cutting
a
a a
a
a a a
IC
BS
RE
15.875
4.76
1.4
1.0
15.875
4.76
1.4
1.0
15.875
4.76
1.4
12.7
3.18
1.4
1.0
Geometry
BS
RE
20
45
S
IC
BS
RE
45
IC
SE545 SEER1504AFEN-JS E
15.875
a a
4.76
1.4
20
S
1.0
BS
RE
45
IC
SE415 SEEN1203EFFR1
QSE415
SEEN1203EFER1
SEEN1203EFTR1
SEEN1203EFSR1
SEKN1203EFSR1
SEKN1203EFTR1
SEKN1203EFTR
SE515 SECN1504EFTR1
SEEN1504EFER1
SEEN1504EFTR1
SEEN1504EFSR1
^L034
SEKN1504EFSR1
SEKN1504EFTR1
SE415 SEER1203EFER-JS E
QSE415
12.7
3.18
1.4
1.0
12.7
3.18
1.4
1.0
12.7
3.18
1.4
1.0
a a
12.7
3.18
1.4
1.0
12.7
3.18
1.4
a
a
a a
12.7
3.18
1.4
12.7
3.18
1.8
1.0
15.875
4.76
1.4
1.0
15.875
4.76
1.4
1.0
15.875
4.76
1.4
1.0
15.875
4.76
1.4
1.0
a
a
a
a
a
a a
15.875
4.76
1.4
15.875
4.76
1.4
12.7
3.18
1.4
1.0
20
S
BS
RE
IC
15
20
S

BS
RE
20
15
IC
ROTATING INSERTS
Work
Material
P
M
K
N
S
H

RE
BS
20
IC
15
K029
ROTATING INSERTS
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round F : Sharp
S : Chamfer + Hone
Order Number
Honing
ASX445
SEET13T3AGEN-JL
^L018
: Unstable Cutting
T : Chamfer
Cermet Carbide Dimensions (mm)
F7030
MC5020
MP6120
MP6130
MP7130
MP7140
MP9120
MP9130
VP15TF
VP30RT
NX4545
Shape
Class
Coated
HTi10
Work
Material
P
M
K
N
S
H
IC
Geometry
13.4 3.97
a a a a a a a a a
R1.5
1.9
R1.5
45
IC
ASX445
^L018
SEGT13T3AGFN-JP
20
S
13.4 3.97
2.2
45
IC
ASX445
^L018
SEMT13T3AGSN-FT M
20
S
13.4 3.97
1.9
R1.5
R1.5
45
IC
ASX445
ROTATING INSERTS
^L018
SEMT13T3AGSN-JH M
13.4 3.97
a a a a a a a a a a
20
S
R1.5
1.9
R1.5
45
IC
ASX445
^L018
SEMT13T3AGSN-JM M
20
S
13.4 3.97
a a a a a a a a a a a
R1.5
1.9
R1.5
45
Corner
Angle 45
SEKN1203AGTN
20
S
IC
12.7 3.18
1.7
R1.0
20
45
IC
BF407
QBF407
SFAN1203ZFFR2
12.7 3.175
SFAN1203ZFFL2
12.7 3.175
SFCN1203ZFFR2
12.7 3.175
SFCN1203ZFFL2
12.7 3.175
2.4
25
IC

a
K030
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round F : Sharp T : Chamfer
BN425 SNC43B2G
DN
SNC43B2S
F
C T 1
SNK43B2G
SNK43B2S
K T 1
F7030
MC5020
MP6120
MP6130
MP7130
MP7140
MP9120
MP9130
VP15TF
VP20RT
VP30RT
NX2525
NX4545
UTi20T
HTi10
TF15
Honing
Order Number
Class
Coated
Shape
: Unstable Cutting
a a
a a
a a a
IC
Geometry
RE
12.7 4.8
12.7 4.8
12.7 4.8
12.7 4.8
2
2
25
IC
^L010
SNGU140812ANFR-L G
SNGU140812ANER-L G
SNGU140812ANER-M G
a a a
SNMU140812ANER-M M
a a a a
SNMU140812ANER-R M
SNMU140812ANER-H M
BN425 SNKF43B2S
DN
SNMF43B2G
14
8.4
1.2
a a
14
8.4
1.2
a a
14
8.4
1.2
a a
14
8.4
1.2
a a a
a a
14
8.4
1.2
a a a
a a
14
8.4
1.2
a
a a a
a
a
12.7 4.8
12.7 4.8
RE
IC
WSX445
6.3
1.
2
2
IC
SNMN120408
12.7 4.78 0.8
SNMN120412
12.7 4.78 1.2
25
RE
IC
ASX400 SOET12T308PEER-JL E
a a a a a a a
12.7 3.97 0.8
RE
1.4
^L040
ROTATING INSERTS
Work
Material
P
M
K
N
S
H
IC
ASX400
SOGT12T308PEFR-JP G
12.7 3.97 0.8

RE
1.4
^L040
IC
ASX400
SOMT12T308PEER-JH M
a a a a a a a a a
12.7 3.97 0.8

RE
1.4
^L040
IC
*1 Grade UTi20T is "E".
K031
ROTATING INSERTS
Work
Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round F : Sharp
SOMT12T308PEEL-JM M
F7030
MC5020
MP6120
MP6130
MP7130
MP7140
MP9120
MP9130
VP15TF
VP30RT
NX2525
NX4545
HTi10
HTi05T
SOMT12T308PEER-JM M
Order Number
a a a a a a a a a a
IC
Geometry
RE
12.7
3.97 0.8
12.7
3.97 0.8
RE
1.4
^L040
Honing
ASX400
Class
Coated
Shape
: Unstable Cutting
IC
ASX400
SOMT12T320PEER-FT M
12.7
a a a
3.97 2.0
RE
0.5
^L040
a a
IC
VOX400
^L036
SONX1206PER
12.7
6.3
IC
FF3000
ROTATING INSERTS
^L149
SPCA53Z
15.88 4.8
11
FF3000
^L149
SPCG53Z
15.88 4.8
IC
IC
11
FP490 SPEN424A
^L150
a a
12.7
3.18 1.6
RE
11
IC
FP590 SPEN535A
^L151
15.875 4.76 2.0

RE
11
S
IC
K032

Work
Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
SPER1203EEER-JS
Dimensions (mm)
Cermet Carbide
F7030
MC5020
VP15TF
UP20M
NX2525
NX4545
UTi20T
HTi10
Honing
FBP415
Order Number
Class
Coated
Shape
: Unstable Cutting
IC
12.7
3.18
BS
RE
1.4
Geometry
BS
11
IC
Corner
Angle 15
SPEN1203EDR
SPKN1203EDR
SPKN1504EDR
*
T 1
*
T
[ [
12.7
3.18
1.4
[ a a
[ [
12.7
3.18
1.4
a [ [
[ [
15.875
4.76
1.4
15
BS
11
IC
15
FBP415
SPEN1203EEER1
12.7
3.175
1.4
SPEN1203EEEL1
12.7
3.175
1.4
SPNN1203EEER1
12.7
3.18
1.3
SPNN1203EEEL1
12.7
3.18
1.3
SPMB1204APT
BS
11
IC
15
BSP
12.7
4.76
1.4
45
IC
S400
S500
SPMN120304
M E 1
SPMN120304T
SPMN120308
a a
SPMN120312
M E 1
SPMN120408
SPMN120412
SPGN120304
G E 1
SPGN120308
SPGN120312
SPMN150408
SPMN150412
SPGN150404
SPGN150408
G E 1
*
E 1
*
12.7
3.18
0.4
12.7
3.18
0.4
a a
12.7
3.18
0.8
a a
12.7
3.18
1.2
a a
12.7
4.76
0.8
12.7
4.76
1.2
a a
a
a a
12.7
3.18
0.4
a a
a a
12.7
3.18
0.8
12.7
3.18
1.2
15.875
4.76
0.8
15.875
4.76
1.2
15.875
4.76
0.4
15.875
4.76
0.8
11
S
ROTATING INSERTS
BS
RE
11
S
IC
RE
11
IC
*1 Grade HTi10 is "F".
K033
ROTATING INSERTS
Work
Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round F : Sharp
Cermet Carbide
Dimensions (mm)
SPMT120408-A
EP6120
VP15TF
VP20RT
UP20M
MP8010
NX2525
NX4545
UTi20T
HTi10
Honing
TBE1
Order Number
Class
Coated
Shape
: Unstable Cutting
IC
12.7
DC
4.76
Geometry
BS RE PRFRAD
0.8
RE
11
S
IC
CESP
CFSP
CGSP
^L113
*
E *1
E *1
E *1
SPMW090304
M E 1
a a a a
9.525
3.18
0.4
SPMW090308
a a a a
9.525
3.18
0.8
SPMW120304
a a a a
12.7
3.18
0.4
SPMW120308
a a a a
12.7
3.18
0.8
RE
11
S
IC
SPX
^L108
SPMX120408-JM M
12.7
a a
4.80
0.8
RE
RE
11
IC
90
SPX
ROTATING INSERTS
^L108
12.7
a a
4.76
0.8
RE
11
IC
SRB
^L120
SRF
2.6
10
12
SRBT16
12
16
SRBT20
15
20
10
SRBT25
18.5 25
12.5
SRBT30
22.5 30
15
SRBT32
23.5 32
16
SRFT10
a a
10 2.6
0.5
SRFT12
a a
10
12 3
0.5
SRFT16
a a
12
16 4
SRFT20
a a
15
20 5
10
SRFT25
a a
18.5
25 6
12.5
SRFT30
a a
22.5
30 7
15
SRFT32
a a
23.5
32 7
16
8.5 10
8.5
2 inserts in one case.

1 Grade NX2525 and NX4545 are "T".

PR
IC
FR
AD
PRFRAD0.006
BS
L0.015
0 .02
-0
SRBT12
*
*
*
*
*
*
*
*
*
SRBT10
90
^L120
K034
SPMX120408-WH M

: Stable Cutting
: General Cutting
Honing :
E : Round
Dimensions (mm)
SRM2
^L128
SRM2&40
&50
16
8.2
3.5
11
SRG20C
19
10.2
4.6
10
10
SRG25C
24
12.8
5.5
12.5
10
SRG30C
28
15.3
15
10
VP15TF
VP20RT
VP30RT
SRG16C
W1
PRFRAD
SRG32C
28
SRG16E
13.5
SRG20E
15.5
8.5
4.6
10
SRG25E
20.5
10.2
5.5
12.5
SRG30E
25.2
12.2
15
SRG32E
26.1
13.1
16
SRG40C
a a a
36
20.5
8.0
20
11
SRG50C
a a a
40
26
8.5
25
11
16.3
6.7
7
3.5
Geometry
AN
16
10
11
AN
L
PRFRAD
AN
PRFRAD
W1
^L134
*
*
Honing
SRM2
^L128
Order Number
Class
Coated
Shape
: Unstable Cutting
W1
Work
Material
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel
W1
P
M
K
N
S
H
AN
^L134
*
*
SRG40E
a a a
32
16.6
8.0
20
11
SRG50E
a a a
35.8
20
8.5
25
11
W1
SRM2&40
&50
AN
L
SRM2
^L128
SRM16C-M
16
8.2
3.5
11
SRM20C-M
19
10.2
4.6
10
10
SRM25C-M
24
12.8
5.5
12.5
10
SRM30C-M
28
15.3
15
10
SRM32C-M
28
16.3
16
10
SRM16E-M
13.5
11
SRM20E-M
15.5
8.5
4.6
10
SRM25E-M
20.5
10.2
5.5
12.5
SRM30E-M
25.2
12.2
15
SRM32E-M
26.1
13.1
16
6.7
3.5
AN 18
PRFRAD
W1
SRM2
^L128
W1
PRFRAD
ROTATING INSERTS
PRFRAD
AN
PRFRAD
K035
ROTATING INSERTS
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
ROTATING INSERTS
NSE300
SE300
10
8.5 2.6
0.5
10
8.5 2.6
SUFT10R20
10
8.5 2.6
SUFT12R05
12
10
1.2
0.5
SUFT12R10
12
10
1.2
SUFT12R20
12
10
1.2
SUFT12R30
12
10
1.2
SUFT16R05
16
12
1.6
0.5
SUFT16R10
16
12
1.6
SUFT16R15
16
12
1.6
1.5
SUFT16R20
16
12
1.6
SUFT16R30
16
12
1.6
SUFT20R05
20
15
0.5
SUFT20R10
20
15
SUFT20R15
20
15
1.5
SUFT20R20
20
15
SUFT20R30
20
15
SUFT25R05
25
18.5 6
2.5
0.5
SUFT25R10
25
18.5 6
2.5
SUFT25R20
25
18.5 6
2.5
SUFT25R30
25
18.5 6
2.5
SUFT30R05
30
22.5 7
0.5
SUFT30R10
30
22.5 7
SUFT30R20
30
22.5 7
SUFT30R30
30
22.5 7
SUFT32R05
32
23.5 7
3.2
0.5
SUFT32R10
32
23.5 7
3.2
SUFT32R20
32
23.5 7
3.2
9.525
3.175
1.4
0.4
9.525
3.175
1.4
0.4
9.525
3.175
1.4
0.4
9.525
3.175
1.4
0.4
RE
Geometry
RE0.010
BS
TEEN1603PEFR1 E F
TEEN1603PEER1 E E
TEEN1603PETR1 E T
TEEN1603PESR1 E S
a
a a
a a a
RE

BS
20
30
IC
K036
L0.015
SUFT10R10
BS
SUFT10R05
-0 0
.0
2
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
IC
DC
Order Number
SUF
^L124
Dimensions (mm)
Cermet Carbide
Class
Honing
F7030
MC5020
VP15TF
UP20M
MP8010
NX2525
NX4545
UTi20T
HTi10
Coated
Shape
: Unstable Cutting
Work
Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
NSE300
SE300
Dimensions (mm)
Cermet Carbide
F7030
MC5020
VP15TF
UP20M
AP10H
NX2525
NX4545
UTi20T
HTi10
Honing
Order Number
Class
Coated
Shape
: Unstable Cutting
IC
BS
TECN1603PEFR1W C
9.525
3.175 1.4
0.4
TECN1603PEER1W C
9.525
3.175 1.4
0.4
TECN1603PETR1W C
9.525
3.175 1.4
0.4
a a a
Geometry
RE
BS
RE
30
NSE300
NSE400
TEER1603PEER-JS E
TEER2204PEER-JS E
9.525
12.7
3.175 1.4
0.4
4.76
1.0
1.4
20
S
IC
Wall face finishing.

RE
BS
30
IC
NSE400
SE400
TECN2204PEFR1
TECN2204PEER1
TECN2204PETR1
TEEN2204PEFR1
TEEN2204PEER1
TEEN2204PETR1
TEEN2204PESR1
TEKN2204PEER1
TEKN2204PESR1
TEKN2204PETR1
TEKN2204PETR
TPEN1603PPR
E T
TPKN1603PPR
K T
TPEN2204PDR
E T
TPKN2204PDR
K T
12.7
4.76
1.4
1.0
12.7
4.76
1.4
1.0
12.7
4.76
1.4
1.0
12.7
4.76
1.4
1.0
12.7
4.76
1.4
1.0
12.7
4.76
1.4
1.0
12.7
4.76
1.4
1.0
12.7
4.76
1.94
12.7
4.76
1.94
12.7
4.76
1.94
a a a
a
a
a a a
a a
a
a
a
4.76
1.94
9.525
3.18
1.2
[ [ [ [
9.525
3.18
1.2
12.7
4.76
1.4
12.7
4.76
1.4
a
[
*1
*1
*1
a [
[
[
a [
[ [ [ [
12.7
BS
RE
PMF

BS
30
11
7.94
3.18
60
TPEW1303ZPER2
20
30
IC
IC
^L142
20
S
ROTATING INSERTS
Work
Material
P
M
K
N
S
H
11
IC
*1 Grade F7030 is "E".
K037
ROTATING INSERTS
Work
Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round F : Sharp
TPMN160312
M E *1
TPMN220404
M E
TPMN220408
M E*
TPMN220412
VIPER TPNX1605N
a a
a a
9.525
3.18
0.4
a a
a a
9.525
3.18
0.8
9.525
a a
IC
BS
RE
3.18
1.2
12.7
4.76
0.4
a a
12.7
4.76
0.8
a a
12.7
4.76
1.2
1 a a
M E *1
N
UTi20T
HTi10
TF15
M E *2
NX2525
TPMN160308
M E *1
Dimensions (mm)
Cermet Carbide
F7030
VP15TF
LC15TF
UP20M
11Positive TPMN160304
Honing
Order Number
Class
Coated
Shape
: Unstable Cutting
9.525
Geometry
RE
11
IC
60
11
IC
ROTATING INSERTS
BXD4000
^L072
BXD4000
22
1.5
0.4
XDGT1550PDER-G08 G
22
1.1
0.8
XDGT1550PDER-G12 G
22
0.7
1.2
XDGT1550PDER-G16 G
22
0.4
1.6
XDGT1550PDER-G20 G
21.7
0.2
2.0
XDGT1550PDER-G30 G
20
0.6
3.0
XDGT1550PDER-G32 G
20
0.4
3.2
XDGT1550PDER-G40 G
19
0.5
4.0
XDGT1550PDER-G50 G
18
0.4
5.0
XDGT1550PDFR-G04 G
22
1.5
0.4
XDGT1550PDFR-G08 G
22
1.1
0.8
XDGT1550PDFR-G12 G
22
0.7
1.2
XDGT1550PDFR-G16 G
22
0.4
1.6
XDGT1550PDFR-G20 G
21.7
0.2
2.0
XDGT1550PDFR-G30 G
20
0.6
3.0
XDGT1550PDFR-G32 G
20
0.4
3.2
XDGT1550PDFR-G40 G
19
0.5
4.0
XDGT1550PDFR-G50 G
18
0.4
5.0
XDGT1550PDFR-GL04 G
22
1.5
0.4
XDGT1550PDFR-GL08 G
22
1.1
0.8
RE
20
30
16
RE
20
30
16
RE
BS
^L072
XDGT1550PDER-G04 G
BS
^L072
BS
BXD4000
30
HTi10 is "F".
*12 Grade
Grade HTi10 is "F", Grade NX2525 is "T".
*
K038

20
16
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round F : Sharp
0.8
XDGX175012PDFR-GL G
23
0.9
1.2
XDGX175016PDFR-GL G
22
1.4
1.6
XDGX175020PDFR-GL G
22
1.0
2.0
XDGX175024PDFR-GL G
22
0.6
2.4
XDGX175030PDFR-GL G
21.1
0.8
3.0
XDGX175032PDFR-GL G
21.1
0.6
3.2
XDGX175040PDFR-GL G
20
0.8
4.0
XDGX175050PDFR-GL G
19.4
0.4
5.0
XDGX227008PDFR-GL G
30
2.0
0.8
XDGX227016PDFR-GL G
30
1.2
1.6
XDGX227020PDFR-GL G
30
0.8
2.0
XDGX227030PDFR-GL G
28.8
0.8
3.0
XDGX227032PDFR-GL G
28.8
0.6
3.2
XDGX227040PDFR-GL G
27.5
0.9
4.0
XDGX227050PDFR-GL G
27
0.4
5.0
XDGX175004PDER-GM G
23.0
1.7
0.4
XDGX175008PDER-GM G
23.0
1.3
0.8
XDGX175012PDER-GM G
23.0
0.9
1.2
XDGX175016PDER-GM G
22.0
1.4
1.6
XDGX175020PDER-GM G
22.0
1.0
2.0
XDGX175024PDER-GM G
22.0
0.6
2.4
XDGX175030PDER-GM G
21.1
0.8
3.0
XDGX175032PDER-GM G
21.1
0.6
3.2
XDGX175040PDER-GM G
20.0
0.5
4.0
XDGX175050PDER-GM G
19.4
0.4
5.0
XDGX175004PDFR-GM G
23.0
1.7
0.4
XDGX175008PDFR-GM G
23.0
1.3
0.8
XDGX175012PDFR-GM G
23.0
0.9
1.2
XDGX175016PDFR-GM G
22.0
1.4
1.6
XDGX175020PDFR-GM G
22.0
1.0
2.0
XDGX175024PDFR-GM G
22.0
0.6
2.4
XDGX175030PDFR-GM G
21.1
0.8
3.0
XDGX175032PDFR-GM G
21.1
0.6
3.2
XDGX175040PDFR-GM G
20.0
0.5
4.0
XDGX175050PDFR-GM G
19.4
0.4
5.0
BS
RE
Geometry
RE
20
S
30
17
.5
RE
20
30
22
.5
RE
20
30
17
.5
ROTATING INSERTS
0.4
1.3
BS
1.7
BS
TF15
23
Order Number
BS
LC15TF
MP9120
^L060
Honing
AXD4000
23
^L060
AXD4000
^L066
XDGX175008PDFR-GL G
AXD7000
XDGX175004PDFR-GL G
^L060
AXD4000
Dimensions (mm)
Carbide
Class
Coated
Shape
: Unstable Cutting
RE
BS
Work
Material
P
M
K
N
S
H
20
30
17
.5
K039
ROTATING INSERTS
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round
Dimensions (mm)
XNMU160732R-MS
XNMU160740R-MS
XNMU160708R-HS
RE
16.0
7.0
11.1
6.5
1.0
0.8
16.0
7.0
11.1
6.5
1.0
1.2
16.0
7.0
11.1
6.5
1.0
1.6
16.0
7.0
11.1
6.5
1.0
2.4
17.3
7.0
11.1
6.5
3.2
18.9
7.0
11.1
6.5
4.0
16.0
7.0
11.1
6.5
1.0
0.8
Geometry
RE
XNMU160724R-MS
BS
INSL
RE
XNMU160716R-MS
W1
INSL
W1
W1
BS
XNMU160712R-MS
MP9030
MP9130
XNMU160708R-MS
BS
VFX5
Honing
VFX5
^L114
Order Number
Class
Coated
Shape
: Unstable Cutting
INSL
Work
Material
P
M
K
N
S
H
16.0
7.0
11.1
6.5
1.0
0.8
L
19.1
9.5
12.7
8.5
1.0
1.2
XNMU190916R-MS
19.1
9.5
12.7
8.5
1.0
1.6
XNMU190924R-MS
19.1
9.5
12.7
8.5
1.0
2.4
XNMU190932R-MS
20.2
9.5
12.7
8.5
3.2
XNMU190940R-MS
21.8
9.5
12.7
8.5
4.0
XNMU190950R-MS
21.8
9.5
12.7
8.5
5.0
XNMU190912R-HS
19.1
9.5
12.7
8.5
1.0
1.2
RE
W1
L
INSL
RE
BS
BS
ROTATING INSERTS
VFX6
XNMU190912R-MS
INSL
VFX6
^L117
W1
INSL
RE
W1
XNMU160708R-LS
BS
VFX5
19.1
9.5
12.7
8.5
1.0
1.2
L
INSL
RE
W1
XNMU190912R-LS
BS
VFX6
K040

Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
E : Round F : Sharp
Dimensions (mm)
13
XPGT13T3PDER-G6
BAP3500
3.97
1.6
0.4
7.9
3.97
1.2
0.8
13
7.9
3.97
0.4
2.4
XPGT13T3PDER-G75 G
13
7.9
3.97
0.4
3.0
XPGT13T3PDER-G8
13
7.9
3.97
0.4
3.2
XPGT13T3PDFR-G1
13
7.9
3.97
1.6
0.4
XPGT13T3PDFR-G2
13
7.9
3.97
1.2
0.8
XPGT13T3PDFR-G6
13
7.9
3.97
0.4
2.4
XPGT13T3PDFR-G75 G
13
7.9
3.97
0.4
3.0
XPGT13T3PDFR-G8
13
7.9
3.97
0.4
3.2
XPMT13T3PDER-M1
a a
13
7.9
3.97
1.6
0.4
XPMT13T3PDER-M2
a a
13
7.9
3.97
1.2
0.8
XPMT13T3PDER-M6
a a
13
7.9
3.97
0.4
2.4
XPMT13T3PDER-M75 M
a a
13
7.9
3.97
0.4
3.0
XPMT13T3PDER-M8
a a
13
7.9
3.97
0.4
3.2
ZCMX083508ER-A
10.4
7.94
3.5
0.8
ZCMX09T308ER-A
a a a
12
9.525
3.97
0.8
RE
75
RE
75
RE
75
11
S
11
S
RE
11
S
RE
W1
DCCC
7.9
Geometry
80
DCCC
ZCMX09T308ER-B
12
9.525
3.97
0.8
RE
W1
RE
ROTATING INSERTS
13
RE
W1
BS
BS
W1
XPGT13T3PDER-G2
W1
BS
XPGT13T3PDER-G1
W1
BAP3500
HTi10
Order Number
F7030
VP15TF
UP20M
MP9030
Shape
Honing
Carbide
Class
Coated
BAP3500
: Unstable Cutting
BS
Work
Material
P
M
K
N
S
H
ZRM0603R-M3
08.5
6.35
3.18
1.2
ZRM0603R-M4
08.5
6.35
3.18
1.6
ZRM0603R-M5
08.5
6.35
3.18
2.0
W1
BAP300
Under-cut type
80
11
87
RE
K041
WIPER INSERTS
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Carbide
HTi05T
MC5020
VP15TF
NX2525
C T
Coated
Cermet
Dimensions (mm)
12.7
W1
15.33
3.18
BS
RE
1.0
Dimensions (mm)
R500
W1
SE445 WEC42AFTR5C
Class
Order Number
Honing
Coated Cermet
Shape
: Unstable Cutting
Honing :
VP25N
Work
Material
P
M
K
N
S
H
RE
45
RE
L
20
S
BS
C E
WEC53AFTR5C
C T
a
a
15.875 18.505 4.76
1.0
15.875 18.505 4.76
1.0
R500
RE 45
W1
SE545 WEC53AFER5C
RE
20
BS
C E
WEC42EFTR5C
C T
a
a
12.7
13.728 3.18
1.0
12.7
13.728 3.18
1.0
R500
RE
W1
SE415 WEC42EFER5C
RE
20
15
BS
WEC53EFTR5C
C T
15.875 16.903 4.76
1.0
R500
RE
RE
20
15
BS
ASX445
^L018
WEEW13T3AGER8C
E E
WEEW13T3AGTR8C
a a
a
a
16.48 16.6
3.97
7.5
1.5
16.48 16.6
3.97
7.5
1.5
20
W1
R500
ROTATING INSERTS
^L034
W1
SE515
29
BS
L
K042
a : Inventory maintained in Japan. [ : Inventory maintained in Japan. To be replaced by new products.

(10 inserts in one case) (CBN and PCD inserts are available in 1 piece in one case)
RE
Work
Material
P
M
K
N
S
H
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
Hardened Steel

: Stable Cutting
: General Cutting
Honing :
Dimensions (mm)
AHX640S
^L026
WNEU2007ZEN7C-WP E E
HTi10
HTi05T
Honing
MC5020
MP6120
VP15TF
NX2525
Order Number
Class

Shape
: Unstable Cutting
W1
IC
20
7.2
BS
RE
7.1
0.8
Geometry
BS RE
IC
AHX640S
^L026
WNEU2006ZEN7C-WK E E
20
6.55
7.4
0.8
BS
AHX640W
^L030
RE
BS
IC
WSX445
WNGU1406ANEN8C-M G E
18.1
a a
14
1.0
W1
^L010
BS
WOEW12T308PETR8C E T
12.5
13.2
3.97
0.8
12.5
13.2
3.97
0.8
ROTATING INSERTS
WOEW12T308PEER8C E E
W1
^L040
R500
ASX400
RE
L
BS
L
VOX400
WOEX1206PER5C
E E
12.5
13.025
5.5
W1
^L036
RE
WPC42EEER10C
C E
12.7
15.163
3.175 10
WPC42EEEL10C
C E
12.7
15.163
3.175 10
15
W1
FBP415
QBP415
R500
11
BS
WPC42W3GR
C F
12.7
14.5
3.2
BS
R2
W1
P425
00
11
S
K043
CBN AND PCD
Dimensions (mm)
NF10000
^L148
Order Number
GDCN2004PDFR3
MD220
Shape
Class
MB730
CBN PCD
20
W1
IC
BS
RE
12.7
4.76
1.2
Geometry
QF10000
W1
RE
L 20
NF10000
GDCN2004ZDTR1
20
12.7
4.76
1.4
0.8
RE
BS
W1
^L148
AF10000
GDCN2004PDR
20
12.7
4.76
20
1.2
W1
RE
L 20
AF5000
LDCN190412R
LDCN190412L
19.05 12.7
4.76
1.2
19.05 12.7
4.76
1.2
RE
W1
15

^L148
NP-GDCN2004PDSR3
20
12.7
4.76
0.8
RE
W1
ROTATING INSERTS
NF10000
V10000
NP-GDCW1240PDFR2 C
9.5
12
2
BS
OCTACUT
^L094
W1
^L147
10
OEMX12T3ETR1
12.7
3.97
C0.5
15 18
20
BS
IC
K044

(10 inserts in one case) (CBN and PCD inserts are available in 1 piece in one case)
Dimensions (mm)
Shape
SE445
Order Number
SECN1203AFFR1
Class
MB710
BC5030
MD220
CBN PCD
IC
12.7
3.18
BS
RE
1.4
1.0
Geometry
RE
BS
IC RE
SE415
SECN1203EFFR1
12.7
3.18
1.4
20
S
1.0
BS
IC
SFCN1203ZFFR2
12.7
3.175
2.4
BS
^L032
SL-ONEN120404ASN
12.7
4.76
0.4
RE
IC
FBP415
SPEN1203EETR1
12.7
3.175
1.4
25
S
IC
AOX445
3
IC
SE300
NSE300
TECN1603PEFR1
9.525
3.175
1.4
BS
11
S
0.4
5 RE
ROTATING INSERTS
BF407
20
RE
BS
20
S
IC
SE400
NSE400
TECN2204PEFR1
12.7
4.76
1.4
1.0
RE
5
BS
20
IC

K045
CBN AND PCD
Dimensions (mm)
PMF
^L142
Order Number
TPEW1303ZPTR2
IC
7.94
3.18
BS
Geometry
RE
60
ROTATING INSERTS
IC
K046

BS
Shape
Class
MB710
MB730
MD220
CBN PCD
11
S
CBN AND PCD WITH WIPER

Dimensions (mm)
Order Number
ASX445
WEEW13T3AGFR3C
WEEW13T3AGTR3C
W1
IC
16.48
16.6
3.97
3.0 1.5
16.48
16.6
3.97
3.0 1.5
BS
Geometry
RE
W1
^L018
MD220
Shape
Class
MB710
CBN PCD
29
RE
BS
BF407
WFC42ZFER2
12.4
3.175 2.4
IC
25
BS
NP-WFC42ZFER2
12.4
3.175 2.4
IC
BS
25
S
ROTATING INSERTS
BF407
K047
DRILLING INSERTS
Dimensions (mm)
TAF
^N240
GCMT
Order Number
IC
RE
GCMT040204-U1
5.0
2.38
0.4
GPMT060204-U1
5.56
2.38
0.4
GPMT070204-U1
6.35
2.38
0.4
GPMT090304-U1
7.94
3.18
0.4
GPMT11T308-U1
GPMT140408-U1
9.525
12.7
Geometry
U1 Breaker
GCMT
95 4
.
RE
Shape
Class
VP15TF
UP20M
GP20M
UE6020
US735
MC1020
MC5020
Coated
3.97
0.8
60
4.76
0.8
GPMT 100
GCMT
GCMT040204-U2
5.0
2.38
0.4
U2 Breaker
GPMT060204-U2
a a
a a
5.56
2.38
0.4
GCMT
GPMT070204-U2
a a
a a
6.35
2.38
0.4
GPMT090304-U2
a a
a a
7.94
3.18
0.4
GPMT11T308-U2
a a
a a
9.525
3.97
0.8
GPMT140408-U2
a a
a a
4.76
0.8
12.7
RE
95 4
.
TAF
MVX
ROTATING INSERTS
^N212
MVX
^N212
60
11
S
IC
GPMT060204-U3
a a
5.56
2.38
0.4
GPMT070204-U3
a a
6.35
2.38
0.4
GPMT090304-U3
a a
7.94
3.18
0.4
GPMT11T308-U3
a a
9.525
3.97
0.8
GPMT140408-U3
a a
12.7
4.76
0.8
SOMX063005-UM
a a
0.5
SOMX073505-UM
a a
3.5
0.5
SOMX084005-UM
a a
8.3
0.5
SOMX094506-UM
a a
9.7
4.5
0.6
SOMX115506-UM
a a
11.6
5.5
0.6
SOMX136008-UM
a a
13.8
0.8
SOMX166508-UM
a a
16.5
6.5
0.8
SOMX187008-UM
a a
18.2
0.8
SOMX063005-US
0.5
SOMX073505-US
3.5
0.5
SOMX084005-US
8.3
0.5
SOMX094506-US
9.7
4.5
0.6
U3 Breaker
GPMT
RE
60
100
11
IC

RE
11
S
IC
RE
11
IC
K048
RE
GPMT 100
GPMT
^N240
IC
TAF
RE
11
GPMT
^N240
TAW H Type
DC(h7)
140
^ N229
TAWNH1400T
TAWNH1410T
TAWNH1420T
TAWNH1430T
TAWNH1440T
TAWNH1450T
TAWNH1460T
TAWNH1470T
TAWNH1480T
TAWNH1490T
TAWNH1500T
TAWNH1510T
TAWNH1520T
TAWNH1530T
TAWNH1540T
TAWNH1550T
TAWNH1560T
TAWNH1570T
TAWNH1580T
TAWNH1590T
TAWNH1600T
TAWNH1610T
TAWNH1620T
TAWNH1630T
TAWNH1640T
TAWNH1650T
TAWNH1660T
TAWNH1670T
TAWNH1680T
TAWNH1690T
TAWNH1700T
TAWNH1710T
TAWNH1720T
TAWNH1730T
TAWNH1740T
TAWNH1750T
TAWNH1760T
TAWNH1770T
TAWNH1780T
TAWNH1790T
TAWNH1800T
TAWNH1810T
TAWNH1820T
TAWNH1830T
TAWNH1840T
VP15TF
VP10H
[
[
DC
LF
14.0
14.1
7.6
7.6
5.0
5.0
14.2
7.6
5.0
14.3
14.4
7.6
7.6
5.0
5.0
14.5
14.6
7.5
7.5
5.0
5.0
14.7
7.5
5.0
14.8
7.5
5.0
14.9
7.5
5.0
15.0
7.4
5.0
15.1
7.4
5.0
[
[
15.2
7.4
5.0
15.3
15.4
7.4
7.4
5.0
5.0
15.5
15.6
7.9
7.9
6.0
6.0
15.7
7.9
6.0
15.8
7.9
6.0
15.9
7.9
6.0
16.0
7.8
6.0
16.1
7.8
6.0
[
[
16.2
7.8
6.0
16.3
16.4
7.8
7.8
6.0
6.0
16.5
16.6
7.7
7.7
6.0
6.0
16.7
7.7
6.0
16.8
7.7
6.0
16.9
7.7
6.0
17.0
7.6
6.0
17.1
7.6
6.0
[
[
17.2
7.6
6.0
17.3
17.4
7.6
7.6
6.0
6.0
17.5
17.6
7.5
7.5
6.0
6.0
17.7
7.5
6.0
17.8
7.5
6.0
17.9
7.5
6.0
18.0
7.4
6.0
18.1
7.4
6.0
[
[
18.2
7.4
6.0
18.3
18.4
7.4
7.4
6.0
6.0
TAWSNH
1400S16
TAWMNH
1400S16
TAWLNH
1400S16
TAWSNH
1500S20
TAWMNH
1500S20
TAWLNH
1500S20
TAWSN
1600S20
TAWMN
1600S20
TAWLN
1600S20
TAWSN
1700S20
TAWMN
1700S20
TAWLN
1700S20
TAWSN
1800S20
TAWMN
1800S20
TAWLN
1800S20
Order Number
TAWNH1850T
TAWNH1860T
TAWNH1870T
TAWNH1880T
TAWNH1890T
TAWNH1900T
TAWNH1910T
TAWNH1920T
TAWNH1930T
TAWNH1940T
TAWNH1950T
TAWNH1960T
TAWNH1970T
TAWNH1980T
TAWNH1990T
TAWNH2000T
TAWNH2010T
TAWNH2020T
TAWNH2030T
TAWNH2040T
TAWNH2050T
TAWNH2060T
TAWNH2070T
TAWNH2080T
TAWNH2090T
TAWNH2100T
TAWNH2110T
TAWNH2120T
TAWNH2130T
TAWNH2140T
TAWNH2150T
TAWNH2160T
TAWNH2170T
TAWNH2180T
TAWNH2190T
TAWNH2200T
TAWNH2210T
TAWNH2220T
TAWNH2230T
TAWNH2240T
TAWNH2250T
TAWNH2260T
TAWNH2270T
TAWNH2280T
TAWNH2290T
a r

a
Dimensions (mm)
Coated
Applicable
Holder
VP15TF
VP10H
Dimensions (mm)
Coated
Order Number
LF
DC
LF
a r
18.5
18.6
9.3
9.3
7.0
7.0
a r
18.7
9.3
7.0
a r
18.8
9.3
7.0
a r
18.9
9.3
7.0
a r
19.0
9.2
7.0
a r
19.1
9.2
7.0
a r
19.2
9.2
7.0
a r
19.3
19.4
9.2
9.2
7.0
7.0
a r
19.5
19.6
9.1
9.1
7.0
7.0
a r
19.7
9.1
7.0
a r
19.8
9.1
7.0
a r
19.9
9.1
7.0
a r
20.0
9.0
7.0
r r
20.1
9.0
7.0
r r
20.2
9.0
7.0
r r
20.3
20.4
9.0
9.0
7.0
7.0
r r
20.5
20.6
8.9
8.9
7.0
7.0
r r
20.7
8.9
7.0
r r
20.8
8.9
7.0
r r
20.9
8.9
7.0
a r
21.0
8.8
7.0
r r
21.1
8.8
7.0
r r
21.2
8.8
7.0
r r
21.3
21.4
8.8
8.8
7.0
7.0
r r
21.5
21.6
10.6
10.6
8.0
8.0
r r
21.7
10.6
8.0
r r
21.8
10.6
8.0
r r
21.9
10.6
8.0
a r
22.0
10.5
8.0
r r
22.1
10.5
8.0
r r
22.2
10.5
8.0
r r
22.3
22.4
10.5
10.5
8.0
8.0
r r
22.5
22.6
10.4
10.4
8.0
8.0
r r
22.7
10.4
8.0
r r
22.8
22.9
10.4
10.4
8.0
8.0
a r
a r
r r
a r
r r
a r
r r
a r
r r
Applicable
Holder
TAWSN
1900S25
TAWMN
1900S25
TAWLN
1900S25
TAWSN
2000S25
TAWMN
2000S25
TAWLN
2000S25
TAWSN
2100S25
TAWMN
2100S25
TAWLN
2100S25
ROTATING INSERTS
Applicable Drill
Shape
Geometry
TAWSN
2200S25
TAWMN
2200S25
TAWLN
2200S25
TAWSN
2300S25
TAWMN
2300S25
TAWLN
2300S25
K049
DRILLING INSERTS
VP15TF
VP10H
LF
r r
23.0
23.1
10.3
10.3
8.0
8.0
r r
23.2
10.3
8.0
r r
23.3
23.4
10.3
10.3
8.0
8.0
r r
23.5
23.6
10.2
10.2
8.0
8.0
r r
23.7
10.2
8.0
r r
23.8
10.2
8.0
r r
23.9
10.2
8.0
a r
24.0
10.1
8.0
r r
24.1
10.1
8.0
r r
24.2
10.1
8.0
r r
24.3
24.4
10.1
10.1
8.0
8.0
r r
24.5
24.6
11.7
11.7
9.0
9.0
r r
24.7
11.7
9.0
r r
24.8
11.7
9.0
r r
24.9
11.7
9.0
a r
25.0
11.6
9.0
r r
25.1
11.6
9.0
r r
25.2
11.6
9.0
r r
25.3
25.4
11.6
11.6
9.0
9.0
r r
25.5
25.6
11.5
11.5
9.0
9.0
r r
25.7
11.5
9.0
r r
25.8
11.5
9.0
r r
25.9
11.5
9.0
a r
26.0
11.4
9.0
r r
26.1
11.4
9.0
r r
26.2
11.4
9.0
r r
26.3
26.4
11.4
11.4
9.0
9.0
a r
r r
a r
r r
a r
r r
a r
r r
TAWSN
2400S32
TAWMN
2400S32
TAWLN
2400S32
TAWSN
2500S32
TAWMN
2500S32
TAWLN
2500S32
TAWSN
2600S32
TAWMN
2600S32
TAWLN
2600S32
TAWNH2650T
TAWNH2660T
TAWNH2670T
TAWNH2680T
TAWNH2690T
TAWNH2700T
TAWNH2710T
TAWNH2720T
TAWNH2730T
TAWNH2740T
TAWNH2750T
TAWNH2760T
TAWNH2770T
TAWNH2780T
TAWNH2790T
TAWNH2800T
TAWNH2810T
TAWNH2820T
TAWNH2830T
TAWNH2840T
TAWNH2850T
TAWNH2860T
TAWNH2870T
TAWNH2880T
TAWNH2890T
TAWNH2900T
TAWNH2910T
TAWNH2920T
TAWNH2930T
TAWNH2940T
TAWNH2950T
TAWNH2960T
TAWNH2970T
TAWNH2980T
TAWNH2990T
TAWNH3000T
TAWNH3010T
TAWNH3020T
TAWNH3030T
TAWNH3040T
DC
LF
r r
26.5
26.6
11.3
11.3
9.0
9.0
r r
26.7
11.3
9.0
r r
26.8
11.3
9.0
r r
26.9
11.3
9.0
a r
27.0
11.2
9.0
r r
27.1
11.2
9.0
r r
27.2
11.2
9.0
r r
27.3
27.4
11.2
11.2
9.0
9.0
r r
27.5
27.6
12.3
12.3
10.0
10.0
r r
27.7
12.3
10.0
r r
27.8
12.3
10.0
r r
27.9
12.3
10.0
a r
28.0
12.2
10.0
r r
28.1
12.2
10.0
r r
28.2
12.2
10.0
r r
28.3
28.4
12.2
12.2
10.0
10.0
r r
28.5
28.6
12.1
12.1
10.0
10.0
r r
28.7
12.1
10.0
r r
28.8
12.1
10.0
r r
28.9
12.1
10.0
a r
29.0
12.0
10.0
r r
29.1
12.0
10.0
r r
29.2
12.0
10.0
r r
29.3
29.4
12.0
12.0
10.0
10.0
r r
29.5
29.6
11.9
11.9
10.0
10.0
r r
29.7
11.9
10.0
r r
29.8
11.9
10.0
r r
29.9
11.9
10.0
a r
30.0
11.8
10.0
r r
30.1
11.8
10.0
r r
30.2
11.8
10.0
r r
30.3
30.4
11.8
11.8
10.0
10.0
a r
r r
a r
r r
a r
r r
a r
r r
TAW H Type
TAWBH2450T
TAWBH2460T
TAWBH2470T
TAWBH2650T
TAWBH2670T
TAWSN
2700S32
TAWMN
2700S32
TAWLN
2700S32
TAWSN
2800S32
TAWMN
2800S32
TAWLN
2800S32
TAWSN
2900S32
TAWMN
2900S32
TAWLN
2900S32
TAWSN
3000S32
TAWMN
3000S32
TAWLN
3000S32
DC
LF
24.5
24.6
11.7
11.7
9.0
9.0
24.7
11.7
9.0
26.5
26.7
11.3
11.3
9.0
9.0
LF
DC(h8)
150
Order Number
Applicable
Holder
Dimensions (mm)
Coated
Applicable Drill
Shape
Geometry
^ N239
TAWSN
2300S25
TAWMN
2300S25
TAWLN
2300S25
Order Number
VP15TF
ROTATING INSERTS
TAWNH2300T
TAWNH2310T
TAWNH2320T
TAWNH2330T
TAWNH2340T
TAWNH2350T
TAWNH2360T
TAWNH2370T
TAWNH2380T
TAWNH2390T
TAWNH2400T
TAWNH2410T
TAWNH2420T
TAWNH2430T
TAWNH2440T
TAWNH2450T
TAWNH2460T
TAWNH2470T
TAWNH2480T
TAWNH2490T
TAWNH2500T
TAWNH2510T
TAWNH2520T
TAWNH2530T
TAWNH2540T
TAWNH2550T
TAWNH2560T
TAWNH2570T
TAWNH2580T
TAWNH2590T
TAWNH2600T
TAWNH2610T
TAWNH2620T
TAWNH2630T
TAWNH2640T
DC
Dimensions (mm)
Coated
Applicable
Holder
VP15TF
VP10H
Dimensions (mm)
Coated
Order Number
K050

TAW H Type
(Cast Iron)
140
DC(h7)
^ N229
DP5010
TAWKH1400TG
TAWKH1410TG
TAWKH1420TG
TAWKH1430TG
TAWKH1440TG
TAWKH1450TG
TAWKH1460TG
TAWKH1470TG
TAWKH1480TG
TAWKH1490TG
TAWKH1500TG
TAWKH1510TG
TAWKH1520TG
TAWKH1530TG
TAWKH1540TG
TAWKH1550TG
TAWKH1560TG
TAWKH1570TG
TAWKH1580TG
TAWKH1590TG
TAWKH1600TG
TAWKH1610TG
TAWKH1620TG
TAWKH1630TG
TAWKH1640TG
TAWKH1650TG
TAWKH1660TG
TAWKH1670TG
TAWKH1680TG
TAWKH1690TG
TAWKH1700TG
TAWKH1710TG
TAWKH1720TG
TAWKH1730TG
TAWKH1740TG
TAWKH1750TG
TAWKH1760TG
TAWKH1770TG
TAWKH1780TG
TAWKH1790TG
TAWKH1800TG
TAWKH1810TG
TAWKH1820TG
TAWKH1830TG
TAWKH1840TG
DC
LF
14.0
14.1
7.1
7.1
5.0
5.0
14.2
7.1
5.0
14.3
14.4
7.1
7.1
5.0
5.0
14.5
14.6
7.0
7.0
5.0
5.0
14.7
7.0
5.0
14.8
7.0
5.0
14.9
7.0
5.0
15.0
6.9
5.0
15.1
6.9
5.0
15.2
6.9
5.0
15.3
15.4
6.9
6.9
5.0
5.0
15.5
15.6
7.3
7.3
6.0
6.0
15.7
7.3
6.0
15.8
7.3
6.0
15.9
7.3
6.0
16.0
7.2
6.0
16.1
7.2
6.0
16.2
7.2
6.0
16.3
16.4
7.2
7.2
6.0
6.0
16.5
16.6
7.1
7.1
6.0
6.0
16.7
7.1
6.0
16.8
7.1
6.0
16.9
7.1
6.0
17.0
7.0
6.0
17.1
7.0
6.0
17.2
7.0
6.0
17.3
17.4
7.0
7.0
6.0
6.0
17.5
17.6
6.8
6.8
6.0
6.0
17.7
6.8
6.0
17.8
6.8
6.0
17.9
6.8
6.0
18.0
6.8
6.0
18.1
6.8
6.0
18.2
6.8
6.0
18.3
18.4
6.8
6.8
6.0
6.0
[
[
[
[
[
[
[
[
Applicable
Holder
TAWSNH
1400S16
TAWMNH
1400S16
TAWLNH
1400S16
TAWSNH
1500S20
TAWMNH
1500S20
TAWLNH
1500S20
TAWSN
1600S20
TAWMN
1600S20
TAWLN
1600S20
TAWSN
1700S20
TAWMN
1700S20
TAWLN
1700S20
TAWSN
1800S20
TAWMN
1800S20
TAWLN
1800S20
Dimensions (mm)
Coated
Order Number
DP5010
Dimensions (mm)
Coated
Order Number
LF
DC
TAWKH1850TG
TAWKH1860TG
TAWKH1870TG
TAWKH1880TG
TAWKH1890TG
TAWKH1900TG
TAWKH1910TG
TAWKH1920TG
TAWKH1930TG
TAWKH1940TG
TAWKH1950TG
TAWKH1960TG
TAWKH1970TG
TAWKH1980TG
TAWKH1990TG
TAWKH2000TG
TAWKH2010TG
TAWKH2020TG
TAWKH2030TG
TAWKH2040TG
TAWKH2050TG
TAWKH2060TG
TAWKH2070TG
TAWKH2080TG
TAWKH2090TG
TAWKH2100TG
TAWKH2110TG
TAWKH2120TG
TAWKH2130TG
TAWKH2140TG
TAWKH2150TG
TAWKH2160TG
TAWKH2170TG
TAWKH2180TG
TAWKH2190TG
TAWKH2200TG
TAWKH2210TG
TAWKH2220TG
TAWKH2230TG
TAWKH2240TG
TAWKH2250TG
TAWKH2260TG
TAWKH2270TG
TAWKH2280TG
TAWKH2290TG
18.5
8.6
7.0
18.6
8.6
7.0
18.7
8.6
7.0
18.8
8.6
7.0
18.9
8.6
7.0
19.0
8.5
7.0
19.1
8.5
7.0
19.2
8.5
7.0
19.3
19.4
8.5
8.5
7.0
7.0
19.5
19.6
8.4
8.4
7.0
7.0
19.7
8.4
7.0
19.8
8.4
7.0
19.9
8.4
7.0
20.0
8.3
7.0
20.1
8.3
7.0
20.2
8.3
7.0
20.3
20.4
8.3
8.3
7.0
7.0
20.5
20.6
8.2
8.2
7.0
7.0
20.7
8.2
7.0
20.8
8.2
7.0
20.9
8.2
7.0
21.0
8.1
7.0
21.1
8.1
7.0
21.2
8.1
7.0
21.3
21.4
8.1
8.1
7.0
7.0
21.5
21.6
9.8
9.8
8.0
8.0
21.7
9.8
8.0
21.8
9.8
8.0
21.9
9.8
8.0
22.0
9.7
8.0
22.1
9.7
8.0
22.2
9.7
8.0
22.3
22.4
9.7
9.7
8.0
8.0
22.5
22.6
9.6
9.6
8.0
8.0
22.7
9.6
8.0
22.8
22.9
9.6
9.6
8.0
8.0
a
a
r
a
r
a
r
a
LF
Applicable
Holder
TAWSN
1900S25
TAWMN
1900S25
TAWLN
1900S25
TAWSN
2000S25
TAWMN
2000S25
TAWLN
2000S25
TAWSN
2100S25
TAWMN
2100S25
TAWLN
2100S25
ROTATING INSERTS
Applicable Drill
Shape
Geometry
TAWSN
2200S25
TAWMN
2200S25
TAWLN
2200S25
TAWSN
2300S25
TAWMN
2300S25
TAWLN
2300S25
K051
DRILLING INSERTS
TAWKH2300TG
TAWKH2310TG
TAWKH2320TG
TAWKH2330TG
TAWKH2340TG
TAWKH2350TG
TAWKH2360TG
TAWKH2370TG
TAWKH2380TG
TAWKH2390TG
TAWKH2400TG
TAWKH2410TG
TAWKH2420TG
TAWKH2430TG
TAWKH2440TG
TAWKH2450TG
TAWKH2460TG
TAWKH2470TG
TAWKH2480TG
TAWKH2490TG
TAWKH2500TG
TAWKH2510TG
TAWKH2520TG
TAWKH2530TG
TAWKH2540TG
TAWKH2550TG
TAWKH2560TG
TAWKH2570TG
TAWKH2580TG
TAWKH2590TG
TAWKH2600TG
TAWKH2610TG
TAWKH2620TG
TAWKH2630TG
TAWKH2640TG
TAWKH2650TG
TAWKH2660TG
TAWKH2670TG
TAWKH2680TG
TAWKH2690TG
TAWKH2700TG
TAWKH2710TG
TAWKH2720TG
TAWKH2730TG
TAWKH2740TG
DC
23.0
9.5
8.0
23.1
9.5
8.0
23.2
9.5
8.0
23.3
23.4
9.5
9.5
8.0
8.0
23.5
23.6
9.4
9.4
8.0
8.0
23.7
9.4
8.0
23.8
9.4
8.0
23.9
9.4
8.0
24.0
9.3
8.0
24.1
9.3
8.0
24.2
9.3
8.0
24.3
24.4
9.3
9.3
8.0
8.0
24.5
24.6
10.8
10.8
9.0
9.0
24.7
10.8
9.0
24.8
10.8
9.0
24.9
10.8
9.0
25.0
10.7
9.0
25.1
10.7
9.0
25.2
10.7
9.0
25.3
25.4
10.7
10.7
9.0
9.0
25.5
25.6
10.6
10.6
9.0
9.0
25.7
10.6
9.0
25.8
10.6
9.0
25.9
10.6
9.0
26.0
10.5
9.0
26.1
10.5
9.0
26.2
10.5
9.0
26.3
26.4
10.5
10.5
9.0
9.0
26.5
26.6
10.4
10.4
9.0
9.0
26.7
10.4
9.0
26.8
10.4
9.0
26.9
10.4
9.0
27.0
10.3
9.0
27.1
10.3
9.0
27.2
10.3
9.0
27.3
27.4
10.3
10.3
9.0
9.0
r
a
r
a
r
a
r
a
LF
TAWSN
2300S25
TAWMN
2300S25
TAWLN
2300S25
TAWSN
2400S32
TAWMN
2400S32
TAWLN
2400S32
TAWSN
2500S32
TAWMN
2500S32
TAWLN
2500S32
TAWSN
2600S32
TAWMN
2600S32
Dimensions (mm)
Coated
Order Number
TAWKH2750TG
TAWKH2760TG
TAWKH2770TG
TAWKH2780TG
TAWKH2790TG
TAWKH2800TG
TAWKH2810TG
TAWKH2820TG
TAWKH2830TG
TAWKH2840TG
TAWKH2850TG
TAWKH2860TG
TAWKH2870TG
TAWKH2880TG
TAWKH2890TG
TAWKH2900TG
TAWKH2910TG
TAWKH2920TG
TAWKH2930TG
TAWKH2940TG
TAWKH2950TG
TAWKH2960TG
TAWKH2970TG
TAWKH2980TG
TAWKH2990TG
TAWKH3000TG
TAWKH3010TG
TAWKH3020TG
TAWKH3030TG
TAWKH3040TG
TAWLN
2600S32
TAWSN
2700S32
TAWMN
2700S32
TAWLN
2700S32

K052
DP5010
ROTATING INSERTS
Order Number
Applicable
Holder
DP5010
Dimensions (mm)
Coated
DC
27.5
11.3
10.0
27.6
11.3
10.0
27.7
11.3
10.0
27.8
11.3
10.0
27.9
11.3
10.0
28.0
11.2
10.0
28.1
11.2
10.0
28.2
11.2
10.0
28.3
28.4
11.2
11.2
10.0
10.0
28.5
28.6
11.1
11.1
10.0
10.0
28.7
11.1
10.0
28.8
11.1
10.0
28.9
11.1
10.0
29.0
11.0
10.0
29.1
11.0
10.0
29.2
11.0
10.0
29.3
29.4
11.0
11.0
10.0
10.0
29.5
29.6
10.9
10.9
10.0
10.0
29.7
10.9
10.0
29.8
10.9
10.0
29.9
10.9
10.0
30.0
10.8
10.0
30.1
10.8
10.0
30.2
10.8
10.0
30.3
30.4
10.8
10.8
10.0
10.0
r
a
r
a
LF
Applicable
Holder
TAWSN
2800S32
TAWMN
2800S32
TAWLN
2800S32
TAWSN
2900S32
TAWMN
2900S32
TAWLN
2900S32
TAWSN
3000S32
TAWMN
3000S32
TAWLN
3000S32
STAW
Applicable Drill
Shape
Geometry
S
VP10H
DC
LF
10.0
10.1
3.8
3.8
4.6
4.6
10.2
3.8
4.6
10.3
10.4
3.8
3.8
4.6
4.6
10.5
10.6
4.0
4.0
4.8
4.8
10.7
4.0
4.8
10.8
10.9
4.0
4.0
4.8
4.8
11.0
11.1
4.2
4.2
5.1
5.1
11.2
4.2
5.1
11.3
11.4
4.2
4.2
5.1
5.1
11.5
11.6
4.4
4.4
5.3
5.3
11.7
4.4
5.3
11.8
11.9
4.4
4.4
5.3
5.3
12.0
12.1
4.6
4.6
5.5
5.5
12.2
4.6
5.5
12.3
12.4
4.6
4.6
5.5
5.5
12.5
12.6
4.8
4.8
5.8
5.8
12.7
4.8
5.8
12.8
12.9
4.8
4.8
5.8
5.8
13.0
13.1
4.9
4.9
6.0
6.0
13.2
4.9
6.0
13.3
13.4
4.9
4.9
6.0
6.0
13.5
13.6
5.1
5.1
6.2
6.2
13.7
5.1
6.2
13.8
13.9
5.1
5.1
6.2
6.2
14.0
14.1
5.3
5.3
6.4
6.4
14.2
5.3
6.4
14.3
14.4
5.3
5.3
6.4
6.4
Applicable Holder
STAWSS1000S16
STAWSN1000S16
STAWMN1000S16
STAWLN1000S16
STAWSS1050S16
STAWSN1050S16
STAWMN1050S16
STAWLN1050S16
STAWSS1100S16
STAWSN1100S16
STAWMN1100S16
STAWLN1100S16
STAWSS1150S16
STAWSN1150S16
STAWMN1150S16
STAWLN1150S16
STAWSS1200S16
STAWSN1200S16
STAWMN1200S16
STAWLN1200S16
STAWSS1250S16
STAWSN1250S16
STAWMN1250S16
ROTATING INSERTS
VP15TF
STAWN1000TH
STAWN1010TH
STAWN1020TH
STAWN1030TH
STAWN1040TH
STAWN1050TH
STAWN1060TH
STAWN1070TH
STAWN1080TH
STAWN1090TH
STAWN1100TH
STAWN1110TH
STAWN1120TH
STAWN1130TH
STAWN1140TH
STAWN1150TH
STAWN1160TH
STAWN1170TH
STAWN1180TH
STAWN1190TH
STAWN1200TH
STAWN1210TH
STAWN1220TH
STAWN1230TH
STAWN1240TH
STAWN1250TH
STAWN1260TH
STAWN1270TH
STAWN1280TH
STAWN1290TH
STAWN1300TH
STAWN1310TH
STAWN1320TH
STAWN1330TH
STAWN1340TH
STAWN1350TH
STAWN1360TH
STAWN1370TH
STAWN1380TH
STAWN1390TH
STAWN1400TH
STAWN1410TH
STAWN1420TH
STAWN1430TH
STAWN1440TH
LF
Dimensions (mm)
Stock
Order Number
140
DC(h8)
^ N220
STAWLN1250S16
STAWSS1300S16
STAWSN1300S16
STAWMN1300S16
STAWLN1300S16
STAWSS1350S16
STAWSN1350S16
STAWMN1350S16
STAWLN1350S16
STAWSS1400S16
STAWSN1400S16
STAWMN1400S16
STAWLN1400S16
K053
DRILLING INSERTS
K054
STAWN1450TH
STAWN1460TH
STAWN1470TH
STAWN1480TH
STAWN1490TH
STAWN1500TH
STAWN1510TH
STAWN1520TH
STAWN1530TH
STAWN1540TH
STAWN1550T
STAWN1560T
STAWN1570T
STAWN1580T
STAWN1590T
STAWN1600T
STAWN1610T
STAWN1620T
STAWN1630T
STAWN1640T
STAWN1650T
STAWN1660T
STAWN1670T
STAWN1680T
STAWN1690T
STAWN1700T
STAWN1710T
STAWN1720T
STAWN1730T
STAWN1740T
STAWN1750T
STAWN1760T
STAWN1770T
STAWN1780T
STAWN1790T
STAWN1800T
STAWN1810T
STAWN1820T
STAWN1830T
STAWN1840T
VP10H
VP15TF
ROTATING INSERTS
Stock
Order Number
Dimensions (mm)
Applicable Holder
DC
LF
14.5
14.6
5.5
5.5
6.7
6.7
14.7
5.5
6.7
14.8
14.9
5.5
5.5
6.7
6.7
15.0
15.1
5.7
5.7
6.9
6.9
15.2
5.7
6.9
15.3
15.4
5.7
5.7
6.9
6.9
15.5
15.6
5.9
5.9
7.1
7.1
15.7
5.9
7.1
15.8
15.9
5.9
5.9
7.1
7.1
STAWSS1600S20
5.9
5.9
7.1
7.1
STAWMN1600S20
16.0
16.1
16.2
5.9
7.1
16.3
16.4
5.9
5.9
7.1
7.1
16.5
16.6
6.3
6.3
7.6
7.6
16.7
6.3
7.6
16.8
16.9
6.3
6.3
7.6
7.6
STAWSS1700S20
17.0
17.1
6.3
6.3
7.6
7.6
STAWMN1700S20
a
a
17.2
6.3
7.6
17.3
17.4
6.3
6.3
7.6
7.6
17.5
17.6
6.7
6.7
8.1
8.1
17.7
6.7
8.1
17.8
17.9
6.7
6.7
8.1
8.1
STAWSS1800S20
6.7
6.7
8.1
8.1
STAWMN1800S20
18.0
18.1
18.2
6.7
8.1
18.3
18.4
6.7
6.7
8.1
8.1
a
a
a
a
a
a
a
a
a
a
a
a
a
a

STAWSS1450S16
STAWSN1450S16
STAWMN1450S16
STAWLN1450S16
STAWSS1500S20
STAWSN1500S20
STAWMN1500S20
STAWLN1500S20
STAWSN1600S20
STAWLN1600S20
STAWSN1700S20
STAWLN1700S20
STAWSN1800S20
STAWLN1800S20
STAW
DC(h8)
Applicable Drill
Shape
Geometry
S
STAWK1000TG
STAWK1010TG
STAWK1020TG
STAWK1030TG
STAWK1040TG
STAWK1050TG
STAWK1060TG
STAWK1070TG
STAWK1080TG
STAWK1090TG
STAWK1100TG
STAWK1110TG
STAWK1120TG
STAWK1130TG
STAWK1140TG
STAWK1150TG
STAWK1160TG
STAWK1170TG
STAWK1180TG
STAWK1190TG
STAWK1200TG
STAWK1210TG
STAWK1220TG
STAWK1230TG
STAWK1240TG
STAWK1250TG
STAWK1260TG
STAWK1270TG
STAWK1280TG
STAWK1290TG
STAWK1300TG
STAWK1310TG
STAWK1320TG
STAWK1330TG
STAWK1340TG
STAWK1350TG
STAWK1360TG
STAWK1370TG
STAWK1380TG
STAWK1390TG
Dimensions (mm)
DC
LF
10.0
10.1
3.3
3.3
4.6
4.6
10.2
3.3
4.6
10.3
10.4
3.3
3.3
4.6
4.6
10.5
10.6
3.5
3.5
4.8
4.8
10.7
3.5
4.8
10.8
10.9
3.5
3.5
4.8
4.8
11.0
11.1
3.7
3.7
5.1
5.1
11.2
3.7
5.1
11.3
11.4
3.7
3.7
5.1
5.1
11.5
11.6
3.9
3.9
5.3
5.3
11.7
3.9
5.3
11.8
11.9
3.9
3.9
5.3
5.3
12.0
12.1
4.1
4.1
5.5
5.5
12.2
4.1
5.5
12.3
12.4
4.1
4.1
5.5
5.5
12.5
12.6
4.2
4.2
5.8
5.8
12.7
4.2
5.8
12.8
12.9
4.2
4.2
5.8
5.8
13.0
13.1
4.4
4.4
6.0
6.0
13.2
4.4
6.0
13.3
13.4
4.4
4.4
6.0
6.0
13.5
13.6
4.6
4.6
6.2
6.2
13.7
4.6
6.2
13.8
13.9
4.6
4.6
6.2
6.2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
LF
Applicable Holder
STAWSS1000S16
STAWSN1000S16
STAWMN1000S16
STAWLN1000S16
STAWSS1050S16
STAWSN1050S16
STAWMN1050S16
STAWLN1050S16
STAWSS1100S16
STAWSN1100S16
STAWMN1100S16
STAWLN1100S16
STAWSS1150S16
STAWSN1150S16
STAWMN1150S16
STAWLN1150S16
STAWSS1200S16
STAWSN1200S16
STAWMN1200S16
STAWLN1200S16
STAWSS1250S16
STAWSN1250S16
STAWMN1250S16
ROTATING INSERTS
DP5010
Stock
Order Number
140
^ N220
STAWLN1250S16
STAWSS1300S16
STAWSN1300S16
STAWMN1300S16
STAWLN1300S16
STAWSS1350S16
STAWSN1350S16
STAWMN1350S16
STAWLN1350S16
K055
DRILLING INSERTS
STAWK1400TG
STAWK1410TG
STAWK1420TG
STAWK1430TG
STAWK1440TG
STAWK1450TG
STAWK1460TG
STAWK1470TG
STAWK1480TG
STAWK1490TG
STAWK1500TG
STAWK1510TG
STAWK1520TG
STAWK1530TG
STAWK1540TG
STAWK1550TG
STAWK1560TG
STAWK1570TG
STAWK1580TG
STAWK1590TG
STAWK1600TG
STAWK1610TG
STAWK1620TG
STAWK1630TG
STAWK1640TG
STAWK1650TG
STAWK1660TG
STAWK1670TG
STAWK1680TG
STAWK1690TG
STAWK1700TG
STAWK1710TG
STAWK1720TG
STAWK1730TG
STAWK1740TG
STAWK1750TG
STAWK1760TG
STAWK1770TG
STAWK1780TG
STAWK1790TG
STAWK1800TG
STAWK1810TG
STAWK1820TG
STAWK1830TG
STAWK1840TG
Applicable
Holder
DC
LF
14.0
4.8
6.4
14.1
4.8
6.4
14.2
4.8
6.4
14.3
14.4
4.8
4.8
6.4
6.4
14.5
14.6
5.0
5.0
6.7
6.7
14.7
5.0
6.7
14.8
14.9
5.0
5.0
6.7
6.7
15.0
15.1
5.2
5.2
6.9
6.9
15.2
5.2
6.9
15.3
15.4
5.2
5.2
6.9
6.9
15.5
15.6
5.3
5.3
7.1
7.1
15.7
5.3
7.1
15.8
5.3
7.1
STAWSS1600S20
15.9
5.3
7.1
STAWSN1600S20
16.0
5.3
7.1
STAWMN1600S20
16.1
5.3
7.1
STAWLN1600S20
16.2
5.3
7.1
16.3
16.4
5.3
5.3
7.1
7.1
16.5
16.6
5.7
5.7
7.6
7.6
16.7
5.7
7.6
16.8
5.7
7.6
STAWSS1700S20
16.9
5.7
7.6
STAWSN1700S20
17.0
5.7
7.6
STAWMN1700S20
17.1
5.7
7.6
STAWLN1700S20
17.2
5.7
7.6
17.3
17.4
5.7
5.7
7.6
7.6
17.5
17.6
6.0
6.0
8.1
8.1
17.7
6.0
8.1
17.8
6.0
8.1
STAWSS1800S20
17.9
6.0
8.1
STAWSN1800S20
18.0
6.0
8.1
STAWMN1800S20
18.1
6.0
8.1
STAWLN1800S20
18.2
6.0
8.1
18.3
18.4
6.0
6.0
8.1
8.1
a
a
a
a
a
a
a
a
a
a

a
K056
Order Number
Dimensions (mm)
DP5010
ROTATING INSERTS
Stock
STAWSS1400S16
STAWSN1400S16
STAWMN1400S16
STAWLN1400S16
STAWSS1450S16
STAWSN1450S16
STAWMN1450S16
STAWLN1450S16
STAWSS1500S20
STAWSN1500S20
STAWMN1500S20
STAWLN1500S20
Memo
K057

OF INDEXABLE MILLING
zOrganized according to the face milling cutting mode.
SCOPE OF AVAILABLE WORK MATERIAL
provides a graph depicting the scope of
the available work material for machining.
PRODUCT FEATURES
CORNER ANGLE ICON
TYPE/
NAME OF
PRODUCT
APPLICATION ICON
represents available
machining applications,
such as finishing
and roughing.
APPLICATION
PRODUCT
SECTION
STANDARDS FOR
APPLICABLE INSERTS
CUTTING MODE ICON

represents available cutting
modes, such as face milling
and shoulder milling.
indicates stock status,

dimensions, etc. for
applicable inserts.
GEOMETRY
INDEXABLE MILLING
FACE MILLING
WSX445
<GENERAL CUTTING>
Steel
Stainless Steel
Cast Iron
Fig.2
Fig.1
Work
Material
Non-ferrous Metal Heat Resistant Alloy Hardened Steel
a Unique design both sides
P
M
K
N
S
H
Steel
Hardened Steel
SNGU140812ANER-L

Dimensions (mm)
Stock Coolant Number

Hole of Teeth DC
R
DCX
LF
DCON CBDP DAH DCCB LCCB BD
KWW
L8
WT APMX Type
(kg) (mm) (Fig.)
WSX445-040A03AR
40
52.8 40 16
18
14
25
37
8.4
5.6
0.3
WSX445-050A03AR
50
62.9 40 22
20
11
17
27
47 10.4
6.3
0.5
WSX445-063A04AR
63
75.9 40 22
WSX445R08004CA
80
92.9 50 25.4
26
13
20
34
56
9.5
1.3
WSX445R10005DA
100 112.9 50 31.75
32
26
45
37
70 12.7
1.8
WSX445R12506EA
125 137.9 63 38.1
36
30
56
42
80 15.9
10
3.2
WSX445R16007FA
160 172.9 63 50.8
38
40
72
45
100 19.14 11
4.9
WSX445R20008KN
200 212.9 63 47.625 35
135
175 25.4
14.22 8.7
WSX445-040A04AR
40
52.8 40 16
18
8.4
5.6
0.3
WSX445-050A04AR
50
62.9 40 22
20
47 10.4
6.3
0.4
WSX445-063A05AR
63
75.9 40 22
20
11
17
27
50 10.4
6.3
0.6
WSX445R08006CA
80
92.9 50 25.4
26
13
20
34
56
1.2
WSX445R10007DA
70 12.7
WSX445R12508EA
125 137.9 63 38.1
36
30
56
42
80 15.9
10
3.1
WSX445R16010FA
10
160 172.9 63 50.8
38
40
72
45
100 19.1
11
4.8
WSX445R20012KN
12
200 212.9 63 47.625 35
135
175 25.4
14.22 8.6
WSX445-050A05AR
50
62.9 40 22
20
11
17
27
47 10.4
6.3
0.4
WSX445-063A06AR
63
75.9 40 22
20
11
17
27
50 10.4
6.3
0.6
WSX445R08008CA
80
92.9 50 25.4
26
13
20
34
56
WSX445R10010DA
10
100 112.9 50 31.75
32
26
45
37
70 12.7
1.6
WSX445R12512EA
12
125 137.9 63 38.1
36
30
56
42
80 15.9
10
3.0
WSX445R16016FA
16
160 172.8 63 50.8
38
40
72
45
100 19.1
11
4.6
WSX445R20020KN
20
200 212.8 63 47.625 35
135
175 25.4
14.22 8.4
100 112.9 50 31.75
20
32
11
9
11
26
17
14
17
45
27
25
27
37
50 10.4
37
9.5
9.5
6.3
0.6
1.7
1.1
Carbide Dimensions (mm)

IC
G F
14 8.4 1.5 1.2
G E
BS RE
a a a a a a
14 8.4 1.5 1.2
SNGU140812ANER-M
G E
a a a a a a
14 8.4 1.5 1.2
SNMU140812ANER-M
M E
a a a a a a a
14 8.4 1.5 1.2
SNMU140812ANER-R
M E
a a a
a a
14 8.4 1.5 1.2
SNMU140812ANER-H
M E
a a a
a a
14 8.4 1.5 1.2
Geometry
WIPER INSERTS
Coated
Shape
Order Number
a a
Dimensions (mm)
L
W1
BS
RE
18.1
14
1.0
Geometry
MILLING
Type
Coarse Pitch
Fine Pitch
MILLING
Extra Fine Pitch
Order Number
Order Number
SNGU140812ANFR-L
KAPR :45
GAMP :+17
T :-7 -2
GAMF :-6 +1 I :+16 +19
: Unstable Cutting
Coated
Shape
Fig.3
prevention function
a Highly efficient chip
discharge
: General Cutting
Honing : E : Round F : Sharp
Non-ferrous Metal
insert
a Sudden fracture & welding
y ARBOR TYPE
Cutting Conditions :
: Stable Cutting
Stainless Steel
Cast Iron
Class
Honing
MC5020
MP6120
MP6130
MP7130
MP9120
VP15TF
VP20RT
TF15
INSERTS WITH BREAKER
Roughing
Class
Honing
MP6120
VP15TF
Finishing
(Note) A set bolt to the arbor is not supplied with the body. Please refer to page L012, when ordering.
WT : Tool Weight
SPARE PARTS
Tool Holder Number
WSX445
Clamp Screw
Wrench (Insert)
TPS4R
TIP15W
* Clamp Torque (N m) : TPS4R=3.5

a
L010
L013

SPARE PARTS
FOR MIILING TOOLS
indicates the names of the
applicable spare parts.
PRODUCT STANDARDS
indicates tool types, order numbers,
dimensions, etc.
PHOTO OF PRODUCT
a To Order :
L000
For title product,

For insert,
please specify zorder number and hand of tool (right/left).

please specify zinsert number and xgrade.
MILLING TOOLS
INDEXABLE MILLING
CLASSIFICATION................
CLASSIFICATION OF SCREW-IN TOOLS ...
CLASSIFICATION OF END MILLS ...
HOW TO SELECT AN END MILL ...
L002
L005
L006
L008
STANDARD OF MILLING
FACE MILLING
WSX445 .....................................
ASX445......................................
AHX640W ..................................
AHX640S ...................................
AOX445 .....................................
SE515 ........................................
SG20 ..........................................
BALL NOSE END MILLING

L010
L018
L030
L026
L032
L034
L033
FACE MILLING (HIGH FEED)
V10000....................................... L147
NF10000 .................................... L148
FF3000....................................... L149
SHOULDER MILLING
VOX400 ..................................... L036

ASX400...................................... L040
BAP300 ..................................... L153
MULTI FUNCTIONAL MILLING
APX3000....................................
APX4000....................................
AXD4000 ...................................
AXD7000 ...................................
BXD4000 ...................................
AQX ...........................................
AJX ............................................
OCTACUT..................................
ARX ...........................................
BRP ...........................................
L046
L052
L060
L066
L072
L076
L084
L094
L098
L102
DEEP SHOULDER MILLING
APX4000LONG CUTTING EDGE TYPE ...

BAP300LONG CUTTING EDGE TYPE ...
SPX ............................................
VFX5 ..........................................
VFX6 ..........................................
L058
L156
L108
L114
L117
SRF,SRB ...................................
SUF ............................................
SRM2 .........................................
SRM2&40, &50 ..........................
CHAMFER MILLING
CESP,CFSP,CGSP .................... L113
T-SLOT MILLING
TSMP ......................................... L136
SPOT MILLING
CBJP,CBMP .............................. L137
SLOT MILLING
KSMG ........................................ L138
VERTICAL FEED MILLING
PMC ........................................... L140

PMF ........................................... L142
PMR ........................................... L143
QUICK CHANGE TYPE
FP490 ........................................
FP590 ........................................
FE404 ........................................
SETTING FIXTURE ...................
L150
L151
L152
L159
ARBOR STANDARDS
FOR SCREW-IN TOOLS ........
Qing SYSTEM ........................
MAXIMUM ALLOWABLE REVOLUTION FOR CUTTER ...
LIST OF CUTTING EDGE DIAMETER TOLERANCES ...
L145
L160
L161
L162

*L026
AHX640S
L152 FE404
L030
L084
L032
L046
L052
L058
L076
L098
L040
L018
L060
L066
L153
L156
L102
L072
L137
L113
AHX640W
AJX
AOX445
APX3000
APX4000
APX4000 LONG CUTTING EDGE TYPE
AQX
ARX
ASX400
ASX445
AXD4000
AXD7000
BAP300
BAP300 LONG CUTTING EDGE TYPE
BRP
BXD4000
CBJP,CBMP
CESP,CFSP,CGSP
L149
L150
L151
L138
L148
L094
L140
L142
L143
L034
L033
L108
L120
L124
L128
L134
L136
L147
L120
L124
L128
L134
FF3000
FP490
FP590
KSMG
NF10000
OCTACUT
PMC
PMF
PMR
SE515
SG20
SPX
SRF,SRB
SUF
SRM2
SRM2& 40,& 50
TSMP
V10000
L114
L117
L036
L010
L145
L159
VFX5
VFX6
VOX400
WSX445
ARBORS FOR SCREW-IN TOOLS
SETTING FIXTURE
L001
INDEXABLE MILLING
CLASSIFICATION
Work Material
Cutting Corner AppliMode Angle cation
Product Name Shape
Corner Angle,
Max. Depth of Cut
Features
Cutter
Dia.
a Unique
WSX445
NEW
45
General Cutting
Steel
design both
sides insert
a Sudden fracture &
welding prevention
function
discharge
40
50
63
80
100
125
160
200
Stainless Steel Cast Iron Non-ferrous Metal Heat Resistant Alloy Hardened Steel
WSX445
(Max. Depth of Cut : 5mm)

^ L010
L002
6
11.5
6
Heavy Cutting
General Cutting
50
63
80
100
125
160
200
250
315
a High rake angle.
a High rigidity due to
carbide shim
100
125
160
ASX445

^ L018
SE515
(Max. Depth of Cut : 11.5mm)

^ L034
a Heptagonal
AHX640S
40
AOX445
V10000
double
sided insert.
a Economical 14
cutting edge inserts.
a Multi insert design
for high feed
machining.
40
double
sided insert.
a Economical 14
a Multi insert design
for high feed
machining.
63
80
100
125
160
200
AHX640S
(
)
Max. Depth of Cut : 6mm
^ L026
a Heptagonal
AHX640W
8
45
CBN octagonal
double sided insert.
a Economical 16 cutting edge
inserts.
(When the depth of cut is 3mm)
a For high efficiency roughing
through to finishing.
a Easy operation and
cleansing.
80
100
125
160
200
250
315
AHX640W

^ L030
a Solid
63
80
100
125
160
200
AOX445

^ L032
a Insert with PCD.

a Suitable for high
NF10000
6
45
inexpensive moulded type

20positive insert.
a Screw-on type.
a A wide range of
chip breakers.
carbide shim.
15
speed finishing of
light alloys.
a Adjustable cutting
edge run-out
function.
80
100
125
NF10000

^ L148
a Insert with PCD.

a Light weight, strong
1.5
MILLING
40
SE515
High Feed Cutting

for Cast Iron
Face Milling
40
45
High Feed Finishing High Efficiency Cutting

for Aluminium Alloy
for Cast Iron
15
a Precision
ASX445
High Feed Finishing

for Aluminium Alloy
45
General Cutting
45
aluminium alloy
cutter body.
a Anti-Fly insert mechanism
enables high speed milling.
a Adjustable cutting edge
run-out function.
63
80
100
125
V10000

^ L147
Work Material
Product Name Shape
Corner Angle,
Max. Depth of Cut
Features
Cutter
Dia.
0.3
High Feed Cutting

for Cast Iron
High Feed Cutting
for Cast Iron
High Feed Cutting
for Cast Iron
a For
125
160
200
250
FF3000

^ L149
0.5
iron finishing.
a Multi-insert design.
a For high feed
cutting.
a Easy tool exchange.
FP490
80
|

^ L150
500
90
a Suitable for cast
0.5
iron finishing.
a For high feed
cutting.
tool exchange.
FP590
125
|

^ L151
500
a Easy
90
a High rake and
relief angle.
a Suitable for light
alloy machining.
tool exchange.
100
|
500
a Easy
FE404

^ L152
a High rigidity double
AJX
clamp structure.
for high
feed machining.
a With through
coolant holes.
a Special insert design
with 3 cutting edges.
a Suitable
a Round shape insert
BRP
with a strong cutting

edge.
a Wide range of tools
available.
a Suitable for mould
machining.
a For octagonal and
OCTACUT
round type inserts.

functional
machining.
a Multi
a Suitable for cast
a High rake angle.
SG20
Multi Functional
Milling
Face Milling
FE404
Multi Functional
Milling
high feed machining.

finishing of steel
machining.
edge run-out
90
function.
FP590
Multi Functional
Milling
a 10003000mm/min
FF3000
FP490
Cutting for Difficult-to-cut

Materials
High Feed Finishing
Steel
with a strong
cutting edge.
a Suitable for
difficult - to - cut
materials.
50
63
80
100
125
160
40
50
63
80
100
AJX

^ L084
MILLING
BRP

^ L104
Small
Insert Type
40
50
63
80
Standard
Insert Type
50
63
80
100
125
160
80
100
125
160
OCTACUT

^ L095
SG20

^ L033
L003
INDEXABLE MILLING
CLASSIFICATION (ARBOR type)

Work Material
Product Name Shape
Corner Angle,
Max. Depth of Cut
Features
Cutter
Dia.
P
Steel
10
For Cast Iron
90
General Cutting
10
accuracy, high
quality vertical wall.
a Low cutting force
insert.
a With through air &
coolant holes.
10
Multi Functional
Cutting
90
accuracy, high
a Low cutting force
insert.
coolant holes.
90
VOX400
(
Max. Depth of Cut : 10mm)

^ L036
50
63
80
100
125
160
200
250
ASX400
^ L040
32
40
50
63
80
100
APX3000

^ L047
resistance
chipbreaker.
a Low resistance insert
and high rigidity design
for excellent
performance.
a For high-speed
machining.
90 a Multi-functional
machining.
40
50
63
80
100
125
160
APX4000

^ L053
a Low
15.5
AXD4000
resistance
chipbreaker.
and high rigidity design
for excellent
performance.
a For high-speed
machining.
90 a Multi-functional
machining.
40
50
63
80
100
125
AXD4000

^ L061
a Low
21
AXD7000
50
63
80
100
125
AXD7000
^ L066
a Curved cutting edge and
BXD4000
15
63
80
100
125
160
200
250
a High
15
General Cutting
For Aluminium Alloy
For Aluminium Alloy
Aluminium Alloy
to Difficult-to-cut Material Cutting
Shoulder Milling
MILLING
L004
a High
APX4000
tolerance
M-class inserts.
a Economical 4
a Curved cutting
edge and high
rigidity holder.
a Screw-on type.
90
APX3000
a High
ASX400
a Vertical
VOX400
inserts
with high strength
cutting edge.
a Economical 8
a Screw-on type.
90
high rigidity holder produce

high wall accuracy.
and high rigidity design for
excellent performance.
a With through coolant holes to
ensure smooth chip discharge.
a For high-speed
machining.
40
50
63
80
100
125
BXD4000
(
)
Max. Depth of Cut : 15mm
^ L072
CLASSIFICATION OF SCREW-IN TOOLS

Product Name Shape
Corner Angle, Max. Depth of Cut
ASX400
Features
a High tolerance M-class
Product Name Shape
ARX
tolerance M-class insert.

a Effective for various
10
machining applications.
a With through air & coolant
holes.
&16 &25
&32, &40
APX3000
10
a High accuracy, high
^ L099
SRF
a S-shaped cutting edge

a Low cutting force insert.
holes.
a Max. depth of cut 10mm.
provides sharpness
similar to that of solid ball
nose end mills.
a Highly accurate corner
radius tolerance allows
for high precision finishing.
a Carbide shank type
available.
&16 &40
90
^ L048
^ L121
APX4000
15
Features
a 15positive, high
inserts.
a Economical 4 cutting
edge
inserts.
high rigidity holder.
a Screw-on type.
90
^ L042
SUF
&16 &32

holes.

for high precision
finishing.
a Seamless gash.
&16 &32
&25 &40
90
^ L054
^ L125
7.4 18
AQX
a The center bottom cutting
SRM2
a Suitable for roughing to
edge enables drilling

without previously formed
hole.
a With through coolant holes.
a Max. depth of cut
7.4 18mm.
semi-finishing of small
and medium moulds.
a High rigidity body design.
a Low resistance
chipbreaker.
a Through coolant hole
type.
&16 &40
&16 &32
^ L130
AJX
a 13 and 15 positive inserts.

a High rigidity double clamp
^ L088
PMC
a For under-cutting trimmed
part of press mould.
structure.
a Suitable for high feed
machining.
a With through coolant
holes.
a Special insert design with
3 cutting edges.
&16 &40
a 2 directional cutting with
large overhang.
&25 &40
MILLING
^ L078
^ L140
L005
INDEXABLE MILLING
CLASSIFICATION
10
^ L042
15.5 , 21
AXD4000
AXD7000
90
^ L060
^ L066
BXD4000
Product Name Shape
VFX5
alloy milling.
a High rigidity design.
a Highly reliable clamping
&40 &80
a Low resistance chipbreaker.

a Low resistance insert and
VFX6
a Vertical inserts with high
strength cutting edge.
high rigidity design for

a For high-speed machining.
a Multi-functional machining.
a Max. depth of cut 15.5,
21mm
a Screw-on type.
a High efficiency milling
&25, &32, &40
WSX445
insert
NEW
prevention function
discharge
45
ASX445
a Precision inexpensive

holes.
45
90
^ L046
a Solid CBN octagonal
double sided insert.

15
MILLING
AOX445

holes.
&25 &63
^ L032
90
(Standard Edge Type)

(Short Edge Type)
AQX
produce optimal finished

surface.
a Multi insert design for
BAP300 &10 &63
BAP300 Long Cutting Edge
&20 &40
17.655
7.423
edge inserts.
(when the depth of cut is 3mm)
a For high efficiency
roughing through to
finishing.
a Easy operation and
cleansing.
a The center bottom cutting
edge enables drilling without

previously formed hole.
a Max. depth of cut
Standard Edge Type=55mm
Short Edge Type=23mm
&16 &50
^ L076
SPX
58 261
a Low cutting resistance
AJX
a 13 and 15 positive inserts.

a High rigidity double clamp
due to the use of wavy

inserts.
a Suitable for heavy cutting
due to holder rigidity.
structure.
machining.
&50
^ L153
^ L156
45
90
a Inserts with wiper edges
moulded type 20positive

insert.
a Screw-on type.
a A wide range of chip
breakers.
carbide shim.
&50 &80
^ L020
&40, &50
^ L012
&12 &63
BAP300
BAP300 Long Cutting Edge
&63 &100
90
15
10
^ L052
^ L058
titanium alloys.
^ L117
high rigidity holder

produce high wall accuracy.
a Low resistance insert and
high rigidity design for
holes to ensure smooth
chip discharge.
90 a Max. depth of cut 15mm.
&20 &40
APX4000
APX4000
Long Cutting Edge
&40 &80
90
90
APX3000
mechanism.
^ L114
^ L074
Features
a High performance titanium
inserts.
edge inserts.
high rigidity holder.
a Screw-on type.
26 75
ASX400
Features
31 90
Product Name Shape
holes.
a Special insert design with
3 cutting edges.
^ L108
L006
90
^ L086
&16 &63
Product Name Shape
ARX
Features
a 15positive, high
Product Name Shape
PMR
Features
tolerance M-class insert.

holes.
large overhang.
a Horizontal feed cutting
and oblique cutting are

also possible.
a Unique shape of curved
edge gives high rigidity
and low resistance.
&10 &25
17
^ L098
&50 &80
^ L143
BRP
a Round shape insert with
SRM2
a Suitable for roughing to
semi-finishing of small
and medium moulds.
a Low resistance
chipbreaker.
a Through coolant hole
type.
a strong cutting edge.

a Wide range of tools
available.
a Suitable for mould
machining.
&12 &63
&16 &30
^ L102
^ L128
OCTACUT
a For octagonal and round
SRM2&40/&50
a Best for roughing of
moulds.
type inserts.
a Multi-functional
machining.
a Low resistance
chipbreaker.
a Highly rigid body.
&32 &63
&40, &50
^ L094
^ L134
a Covers 5 cutting modes.
a Excellent sharpness with
SRF
a S-shaped cutting edge
provides sharpness
similar to that of solid ball
nose end mills.
for high precision finishing.
a Carbide shank type
available.
11positive inserts.
a 30, 45 and 60 chamfer
series.
^ L113
30
45
60
10.2(30)
8.3(45)
5.9(60)
&4 &32
TSMP
^ L120
11
14
18
a T-groove order number
SUF
&10 &32
14, 18 and 22 are

available.
a 86 rhombic shape 11
positive insert.
a Shoulder milling and
inversed spot facing are
also possible.

for high precision
finishing.
a Seamless gash.
&10 &32
MILLING
CESP CFSP CGSP
&25 &40
^ L136
CBJP CBMP
^ L124
a Capable of spot facing
KSMG
a Side face grooving tool
machining, boring and

interpolation.
a For seat machining of
hexagon socket head bolt
(M8-M30).
a 86rhombic shape
11positive insert.
for machining centers.

diameter is & 25mm for

internal grooving.
a For groove widths of
1.25mm 6.0mm.
&25, &40
&14 &48
^ L137
PMF
^ L138
a 2 directional cutting
with large overhang.

a Excellent straightness.
a Excellent wall accuracy.
&50 &80
^ L142
L007
INDEXABLE MILLING
CLASSIFICATION
Product Name
Cutting Mode
Slot Milling
Shoulder Milling
Spot Milling
Pocket Milling
Chamfer Milling
MILLING
Radius Milling
Drilling
Copy Milling
Face Milling
L008
ASX400
^ L042
APX3000 APX4000
APX4000
^ L046
^ L052
^ L058
BAP300
^ L153
BAP300 AXD4000 BXD4000

Long Cutting Edge AXD7000
^ L156
^ L060
^ L066
^ L074
VFX5
VFX6
^ L114
^ L117
SPX
^ L108
WSX445
^ L012
ASX445
^ L020
AOX445
^ L032
AJX
ARX
BRP
OCTACUT
^ L076
^ L086
^ L098
^ L102
^ L094
CESP
CFSP
CGSP
^ L113
TSMP
^ L136
CBJP
CBMP
^ L137
PMF
PMR
PMC
^ L142
^ L143
^ L140
SRM2
SRF
SUF
^ L128
^ L134
^ L120
^ L124
KSMG
^ L138
MILLING
AQX
MULTI
MULTI
MULTI
MULTI
FUNCTIONAL FUNCTIONAL FUNCTIONAL FUNCTIONAL
TYPE
TYPE
TYPE
TYPE
L009
INDEXABLE MILLING
insert
Extra Fine Pitch
MILLING
Fine Pitch
Coarse Pitch
Type
y ARBOR TYPE
APMX
45
DCX
LF
KWW
L8
WT APMX Type
(kg) (mm) (Fig.)
WSX445-040A03AR
40
52.8 40 16
18
14
25
37
8.4
5.6
0.3
WSX445-050A03AR
50
62.9 40 22
20
11
17
27
47 10.4
6.3
0.5
WSX445-063A04AR
63
75.9 40 22
20
11
17
27
50 10.4
6.3
0.6
WSX445R08004CA
80
92.9 50 25.4
26
13
20
34
56
1.3
WSX445R10005DA
100 112.9 50 31.75
32
26
45
37
70 12.7
1.8
WSX445R12506EA
125 137.9 63 38.1
36
30
56
42
80 15.9
10
3.2
WSX445R16007FA
160 172.9 63 50.8
38
40
72
45
100 19.14 11
4.9
WSX445R20008KN
200 212.9 63 47.625 35
135
175 25.4
WSX445-040A04AR
40
52.8 40 16
18
14
25
37
8.4
5.6
0.3
WSX445-050A04AR
50
62.9 40 22
20
11
17
27
47 10.4
6.3
0.4
WSX445-063A05AR
63
75.9 40 22
20
11
17
27
50 10.4
6.3
0.6
WSX445R08006CA
80
92.9 50 25.4
WSX445R10007DA
WSX445R12508EA
125 137.9 63 38.1
36
30
56
WSX445R16010FA
10
160 172.9 63 50.8
38
40
72
WSX445R20012KN
12
200 212.9 63 47.625 35
135
WSX445-050A05AR
50
62.9 40 22
20
11
WSX445-063A06AR
63
75.9 40 22
20
11
WSX445R08008CA
80
92.9 50 25.4
26
13
20
34
56
9.5
1.1
WSX445R10010DA
10
100 112.9 50 31.75
32
26
45
37
70 12.7
1.6
WSX445R12512EA
12
125 137.9 63 38.1
36
30
56
42
80 15.9
10
3.0
WSX445R16016FA
16
160 172.8 63 50.8
38
40
72
45
100 19.1
11
4.6
WSX445R20020KN
20
200 212.8 63 47.625 35
135
175 25.4
14.22 8.4
100 112.9 50 31.75
9.5
14.22 8.7
26
13
20
34
56
9.5
1.2
32
26
45
37
70 12.7
1.7
42
80 15.9
10
3.1
45
100 19.1
11
4.8
175 25.4
14.22 8.6
17
27
47 10.4
6.3
0.4
17
27
50 10.4
6.3
0.6
WT : Tool Weight
SPARE PARTS
*
Tool Holder Number
WSX445

a
L010
18
DCCB
DC
DCX
Dimensions (mm)

Hole of Teeth DC
R
45
CBDP
LF
200
KAPR :45
GAMP :+17
T :-7-2
GAMF :-6 +1 I :+16+19
Order Number
DAH
DCCB
DC
DCX
BD
101.6
DCON
KWW
Fig.3
prevention function
discharge
L8
L8
DAH
DCCB
45
DC
DCX
100
125
160
CBDP
LF
BD
DCON
KWW
Fig.2
APMX
40
50
63
80
BD
DCON
KWW
L8
K
Cast Iron
Fig.1
LCCB
M
Stainless Steel
Roughing
LCCB
P
Steel
Finishing
CBDP
LF
<GENERAL CUTTING>
APMX
FACE MILLING
WSX445
Clamp Screw
Wrench (Insert)
TPS4R
TIP15W
200
L8
CBDP
LF
APMX
45
M16
L8
Order Number

Hole of Teeth DC
R
CBDP
LF
45
DCCB
DC
DCX
APMX
45
Dimensions (mm)
DCX
LF
KWW
L8
WT APMX Type
(kg) (mm) (Fig.)
WSX445-040A03AR
40
52.8
40
16
18
14
25
37
8.4
5.6
0.3
WSX445-050A03AR
50
62.9
40
22
20
11
17
27
47
10.4
6.3
0.5
WSX445-063A04AR
63
75.9
40
22
20
11
17
27
50
10.4
6.3
0.6
WSX445-080A04AR
80
92.9
50
27
23
13
20
34
56
12.4
1.3
WSX445-100B05AR
100 112.9
50
32
26
26
45
32
78
14.4
1.9
WSX445-125B06AR
125 137.9
63
40
28
30
56
40
89
16.4
3.4
WSX445-160C07NR
160 172.9
63
40
40
56
100
16.4
4.9
WSX445-200C08NR
200 212.9
63
60
32
135
160
25.7 14.22 7.5
WSX445-040A04AR
40
52.8
40
16
18
14
25
37
8.4
5.6
0.3
WSX445-050A04AR
50
62.9
40
22
20
11
17
27
47
10.4
6.3
0.4
WSX445-063A05AR
63
75.9
40
22
20
11
17
27
50
10.4
6.3
0.6
WSX445-080A06AR
80
92.9
50
27
23
13
20
34
56
12.4
1.2
WSX445-100B07AR
100 112.9
50
32
26
26
45
32
78
14.4
1.9
WSX445-125B08AR
125 137.9
63
40
28
30
56
40
89
16.4
3.4
WSX445-160C10NR
10
160 172.9
63
40
40
56
100
16.4
4.8
WSX445-200C12NR
12
200 212.9
63
60
32
135
160
25.7 14.22 7.4
WSX445-050A05AR
50
62.9
40
22
20
11
17
27
47
10.4
6.3
0.4
WSX445-063A06AR
63
75.9
40
22
20
11
17
27
50
10.4
6.3
0.6
WSX445-080A08AR
80
92.9
50
27
23
13
20
34
56
12.4
1.1
WSX445-100B10AR
10
100 112.9
50
32
26
26
45
32
78
14.4
1.8
WSX445-125B12AR
12
125 137.9
63
40
28
30
56
40
89
16.4
3.2
WSX445-160C16NR
16
160 172.8
63
40
40
56
100
16.4
4.6
WSX445-200C20NR
20
200 212.8
63
60
32
135
160
25.7 14.22 7.2
MILLING
Extra Fine Pitch
Fine Pitch
Coarse Pitch
Type
y ARBOR TYPE
DCCB
DC
DCX
KAPR :45
GAMP :+17
T :-7 -2
GAMF :-6 +1 I :+16+19
APMX
L8
Fig.4
BD
DCON 14
KWW
DAH
DCCB
DC
DCX
BD
101.6
DCON
18
KWW
CBDP
LF
160
L8
Fig.3
APMX
DAH
DCCB
45
DC
DCX
100
125
LCCB
The cutter bore diameter DCON is

indicated in millimetre.
BD
DCON
KWW
Fig.2
LCCB
40
50
63
80
For metric arbors
BD
DCON
KWW
CBDP
LF
Fig.1
WT : Tool Weight
L011
DCX
DC
DCON
INDEXABLE MILLING
45
APMX
LH
LF
Fine Pitch
Coarse Pitch
Type
y SHANK TYPE
Dimensions (mm)

Hole of Teeth
R
Order Number
DC
DCX
LF
DCON
LH
WT
(kg)
APMX
(mm)
WSX445R4003SA32M
40
52.8
125
32
40
0.8
WSX445R5003SA32M
50
62.9
125
32
40
1.0
WSX445R6304SA32M
63
75.9
125
32
40
1.2
WSX445R8004SA32M
80
92.9
125
32
40
1.6
WSX445R4004SA32M
40
52.8
125
32
40
0.8
WSX445R5004SA32M
50
62.9
125
32
40
1.0
WSX445R6305SA32M
63
75.9
125
32
40
1.2
WSX445R8006SA32M
80
92.9
125
32
40
1.5
* WT : Tool Weight
SPARE PARTS
*
Tool Holder Number
Clamp Screw
Wrench (Insert)
TPS4R
TIP15W
WSX445

SET BOLT (SOLD SEPARATELY)
Set Bolt
Order Number
WSX445-040AooAR
WSX445-050AooAR
WSX445-063AooAR
HSC08025H
HSC10030H
HSC08040
HSC10035
1
1
HSC10030H
HSC10035
WSX445-080AooAR
HSC12035H
13 M81.25
16 M101.5
33
8
40 10
5
6
16 M101.5
HSC12035
HSC12045
18 M121.75
40 M162
40 10
6
47
12 10
57
43 10 14
50 M202.5
54 14 17
6 27
2
1
50 M202.5
24 M162
54 14 17
43 16 14
6 27
6 23
HSC12035
HSC12045
18 M121.75
WSX445R100ooDA
WSX445R125ooEA
WSX445R160ooFA
WSX445R200ooKN
MBA16033H
40 M162
47
12 10
57
43 10 14
MBA20040H
50 M202.5
54 14 17
MBA24045H
2
2
65 M243
24 M162
59 14 17 10 37
43 16 14
L012
6 23
HSC12035H
(Note 1) Internal coolant is necessary with the set bolt.

"Confirmation method" (See the figure at the right.)
z Cutting dimensions "DAH" and "DCCB" shall be larger than bore diameters "&a" and "&g".
x Cutting dimension "LF-LCCB" shall be larger than bolt dimension "d".
WSX445R080ooCA
No coolant hole
Fig.1
a
Fig.2
MILLING
Order Number
Geometry
b
g
Without coolant
hole
WSX445-100BooAR MBA16033H
WSX445-125BooAR MBA20040H
WSX445-160CooNR No coolant hole
WSX445-200CooNR No coolant hole
Reference Dimensions (mm)
Type
With coolant
hole
Arbor Type
6 23
6 27
d
e

Steel
: Stable Cutting
Stainless Steel
: Unstable Cutting
Honing : E : Round F : Sharp
Non-ferrous Metal
Hardened Steel
Carbide Dimensions (mm)
Class
Honing
MC5020
MP6120
MP6130
MP7130
MP9120
VP15TF
VP20RT
TF15
Coated
Shape
: General Cutting
Cast Iron
IC
SNGU140812ANFR-L
G F
14 8.4 1.5 1.2
SNGU140812ANER-L
G E
a a a a a a
14 8.4 1.5 1.2
SNGU140812ANER-M
G E
a a a a a a
14 8.4 1.5 1.2
SNMU140812ANER-M
M E
a a a a a a a
14 8.4 1.5 1.2
SNMU140812ANER-R
M E
a a a
a a
14 8.4 1.5 1.2
SNMU140812ANER-H
M E
a a a
a a
14 8.4 1.5 1.2
Order Number
Geometry
BS RE
RE
IC
Work
Material
P
M
K
N
S
H
6.3
BS
WIPER INSERTS
a a
W1
BS
RE
18.1
14
1.0
Geometry
BS
RE
L
MILLING
Order Number
Dimensions (mm)
W1
Shape
Class
Honing
MP6120
VP15TF
Coated
L013
INDEXABLE MILLING
y Dry cutting
vc
(m/min)
MP6120
VP15TF
250 (200 300)
0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
MP6130
VP20RT
240 (190 290)
0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
MP6120
VP15TF
220 (170270)
0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
MP6130
VP20RT
200 (150250)
0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
MP6120
VP15TF
140 (100180)
0.15 (0.1 0.2)
< 2.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
MP6130
VP20RT
120 (90150)
0.15 (0.1 0.2)
< 2.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
MP7130
VP15TF
VP20RT
200 (150 250)
0.15 (0.1 0.2)
< 2.0
0.2 (0.15 0.25)
< 3.0
Austenitic
Stainless Steel
>200HB
MP7130
VP15TF
VP20RT
170 (120220)
0.15 (0.1 0.2)
< 2.0
0.2 (0.15 0.25)
< 3.0
Two-phase
Stainless Steel
< 280MPa
MP7130
VP15TF
VP20RT
160 (110210)
0.15 (0.1 0.2)
< 2.0
0.2 (0.15 0.25)
< 3.0
<450HB
MP7130
VP15TF
VP20RT
150 (100200)
0.15 (0.1 0.2)
< 2.0
0.2 (0.15 0.25)
< 3.0
MC5020
220 (200270)
0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
VP15TF
VP20RT
180 (130250)
0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
MC5020
200 (180250)
0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
VP15TF
VP20RT
160 (110240)
0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
VP15TF
50 (30 70)
0.05 (0.05 0.1)
< 1.5
0.1 (0.05 0.15)
< 2.0
Hardness
P
Mild Steel
Carbon Steel
Alloy Steel
(AISI 1045, AISI 4140,

AISI 4340)
Alloy Steel
Pre-Hardened Steel
(AISI D2, SKD61,
SKT4, AISI P21,
AISI P20)
Austenitic
Stainless Steel
Ferritic and
Martensitic
Stainless Steel
< 180HB
180 350HB
35 45HRC

(AISI 410, AISI 430,
AISI 431, AISI 420)
(AISI 329)
Hardened
Stainless Steel
K
Gray Cast Iron
MILLING
(FC300)
Ductile Cast Iron

(FCD700)
Finish Light Cutting Light Rough Cutting Medium Heavy Cutting

L, M Breaker
M, R Breaker
R, H Breaker
fz (mm/t.)
ap(mm)
fz (mm/t.)
ap(mm)
fz (mm/t.)
ap(mm)
Grade
Work Material
Hardened Steel
(AISI H13, JIS SKT4)
Tensile Strength
< 350MPa
Tensile Strength
< 800MPa
40 55HRC
to the table above and set the cutting conditions to match the application.
* Refer
Wet cutting is recommended, when focusing on the surface finish. (Life is lower than dry cutting.)
*
L014
y Wet cutting
Hardness
P
Mild Steel
Carbon Steel
Alloy Steel
(AISI 1045, AISI 4140,

AISI 4340)
Alloy Steel
Pre-Hardened Steel
(AISI D2, SKD61,
SKT4, AISI P21,
AISI P20)
Austenitic
Stainless Steel
Ferritic and
Martensitic
Stainless Steel
< 180HB
150 (100 200) 0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
120 (80 160)
0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
100 (80 120)
0.15 (0.1 0.2)
< 2.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
MP6130
VP20RT
MP6120
VP15TF
180 350HB
MP6130
VP20RT
MP6120
VP15TF
35 45HRC
MP6130
VP20RT
MP7130
VP15TF
VP20RT
130 (80 180)
0.15 (0.1 0.2)
< 2.0
0.2 (0.15 0.25)
< 3.0
Austenitic
Stainless Steel
>200HB
MP7130
VP15TF
VP20RT
100 (80 150)
0.15 (0.1 0.2)
< 2.0
0.2 (0.15 0.25)
< 3.0
Two-phase
Stainless Steel
< 280MPa
MP7130
VP15TF
VP20RT
100 (80 150)
0.15 (0.1 0.2)
< 2.0
0.2 (0.15 0.25)
< 3.0
<450HB
MP7130
VP15TF
VP20RT
90 (50 140)
0.15 (0.1 0.2)
< 2.0
0.2 (0.15 0.25)
< 3.0
MC5020
180 (160 200) 0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
VP15TF
VP20RT
130 (100 160)
0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
MC5020
180 (160 200) 0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
VP15TF
VP20RT
110 (80140)
0.15 (0.1 0.2)
< 3.0
0.2 (0.15 0.25)
< 4.0
0.25 (0.2 0.3)
< 5.0
300
0.2 (0.1 0.3)
< 5.0
(AISI 329)
Hardened
Stainless Steel
K
Gray Cast Iron
(FC300)
Ductile Cast Iron

(FCD700)
Aluminium Alloy
Titanium Alloy
(Ti-6AI-4V)

(Inconel718)

L, M Breaker
M, R Breaker
R, H Breaker
fz (mm/t.)
ap(mm)
fz (mm/t.)
ap(mm)
fz (mm/t.)
ap(mm)
vc
(m/min)
MP6120
VP15TF

(AISI 410, AISI 430,
AISI 431, AISI 420)
Grade
Hardened Steel
(AISI H13, JIS SKT4)
< 350MPa
< 800MPa
TF15
MP9120
VP15TF
VP20RT
50 (40 60)
0.05 (0.05 0.1)
< 1.5
0.1 (0.05 0.15)
< 2.0
MP9120
VP15TF
VP20RT
40 (20 50)
0.05 (0.05 0.1)
< 1.5
0.1 (0.05 0.15)
< 2.0
40 55HRC
VP15TF
50 (30 70)
0.05 (0.05 0.1)
< 1.5
0.1 (0.05 0.15)
< 2.0
MILLING
Work Material
to the table above and set the cutting conditions to match the application.
* Refer
Wet cutting is recommended, when focusing on the surface finish. (Life is lower than dry cutting.)
*
L015
INDEXABLE MILLING
FEATURES
Conical seating surface prevents
insert breakage
Anti Fly Insert (AFI) and conical
insert seat hold the insert securely
and prevent damage to the seat
and body even if sudden fracture
occured. The thick insert eliminates
the need of shim.
Extremely quiet, fly-free insert

Mitsubishi Materials
proprietary Double
sided, Z Geometry insert
features a low resistance
Cutting
and sharp cutting edge
edge
Double sided, Z Geometry while being a negative
(double sided) insert.
WSX445
Axial center line
Anti Fly Insert mechanism (AFI)
Coolant holes
26*
Improves chip discharge and prevents chip welding

applicable to some carbides
* Not
Purchase the set bolt separately when using internal coolant.
*
Excellent cutting
edge sharpness
Unique double
sided finished
(4 corners X 2)
* Rake angle when insert installed

y BREAKER
SYSTEM
MILLING
Breaker series capable of various cutting
Focus on
cutting edge
sharpness
Thin sheet, low rigidity
L Breaker
Focus on cutting edge

sharpness
Low resistance type
a Precision grinding
Interrupted cutting, with scale
M Breaker
1st Recommendation
All-around
a General ungrounded precision
a Precision grinding
(improved cutting surface)
L016
R Breaker
Rough Cutting
Reinforced edge type
H Breaker
Focus on
cutting edge
strength
Heavy cutting and forced

interrupted cutting
Reinforced edge type
y Instructions for use of wiper inserts
Fig.1
Fig.2
a These wiper inserts have 2 corners.

a Install the insert so that the cutting edge is located as shown in Fig.1.
Do not install the wiper insert as shown in Fig.2. (The insert may be damaged by a too heavy cutting load.)
a Excellent finished surface can be obtained with one wiper insert.
a When the feed per revolution is larger than the width of the wiper edge, install 2 or more wiper inserts equally inside the cutting
MILLING
body.
L017
INDEXABLE MILLING
Type
Extra Fine Pitch
MILLING
Fine Pitch
Coarse Pitch
Order Number
Fig.3
18
DCCB
DC
DCX
KAPR :45
GAMP :+20 +23 T :+449 +953
GAMF :-13 -10 I :+2255 +2302
Stock Number
R of Teeth
Fig.4
315
M20
45

Dimensions(mm)
DC
DCX
LF
L8
BD
177.8
101.6
DCON
KWW
DCON CBDP DAH DCCB
45
22
45
18
CBDP
LF
CBDP
LF
200
250
BD
101.6
DCON
M16 KWW
DCCB
DC
DCX
L8
ed type 20positive insert.

a Screw-on type.
a A wide range of chip
breakers.
a High rigidity due to carbide
shim.
45
APMX
DAH
DC
DCX
APMX
a Precision inexpensive mould-
y ARBOR TYPE
80
100
125
160
CBDP
LF
CBDP
50
63
BD
DCON
KWW
Fig.2
APMX
K
Cast Iron
BD
DCON
KWW
Fig.1
L8
M
Stainless Steel
Roughing
APMX
P
Steel
Finishing
LF
<GENERAL CUTTING>
L8
FACE MILLING
ASX445
DCCB
DC
DCX
BD
KWW
L8
WT
(kg)
APMX
(mm)
Type
(Fig.)
ASX445-050A03R
50
63.0
40 22
20
11
45
10.4
6.3
0.5
ASX445-063A04R
63
75.9
40 22
20
11
50
10.4
6.3
0.7
ASX445R08004C
80
93.2
50 25.4
26
38
56
9.5
1.1
ASX445R10005D
100
113.2
50 31.75
32
45
70
12.7
1.8
ASX445R12506E
125
138.0
63 38.1
35
60
80
15.9
10
2.9
ASX445R16007F
160
173.0
63 50.8
38
80
100
19.1
11
4.7
ASX445R20008K
200
212.9
63 47.625
35
140
175
25.4
14.22
7.9
ASX445R25010K
10
250
262.9
63 47.625
35
180
220
25.4
14.22
12.9
ASX445R31514P
14
315
327.9
63 47.625
40
245
285
25.4
14.22
22.4
ASX445-050A04R
50
63.0
40 22
20
11
45
10.4
6.3
0.4
ASX445-063A05R
63
75.9
40 22
20
11
50
10.4
6.3
0.6
ASX445R08006C
80
93.2
50 25.4
26
38
56
9.5
1.0
ASX445R10007D
100
113.2
50 31.75
32
45
70
12.7
1.7
ASX445R12508E
125
138.0
63 38.1
35
60
80
15.9
10
2.8
ASX445R16010F
10
160
173.0
63 50.8
38
80
100
19.1
11
4.6
ASX445R20012K
12
200
212.9
63 47.625
35
140
175
25.4
14.22
7.8
ASX445R25014K
14
250
262.9
63 47.625
35
180
220
25.4
14.22
12.8
ASX445R31518P
18
315
327.9
63 47.625
40
245
285
25.4
14.22
22.2
ASX445-050A05R
50
63.0
40 22
20
11
45
10.4
6.3
0.4
ASX445-063A06R
63
75.9
40 22
20
11
50
10.4
6.3
0.6
ASX445R08008C
80
93.2
50 25.4
26
38
56
9.5
1.1
ASX445R10010D
10
100
113.2
50 31.75
32
45
70
12.7
1.8
ASX445R12512E
12
125
138.0
63 38.1
35
60
80
15.9
10
2.9
ASX445R16016F
16
160
173.0
63 50.8
38
80
100
19.1
11
4.7
ASX445R20020K
20
200
212.9
63 47.625
35
140
175
25.4
14.22
7.8
ASX445R25024K
24
250
262.9
63 47.625
35
180
220
25.4
14.22
12.8
ASX445R31528P
28
315
327.9
63 47.625
40
245
285
25.4
14.22
21.8
WT : Tool Weight
SPARE PARTS
z
Tool Holder
Number
Shim
x
*c
Shim Screw
Clamp Screw Wrench (Insert) Wrench (Shim)
Insert
ASX445
STASX445N WCS503507H
* Clamp Torque (N m) : WCS503507H=5.0, TPS35=3.5

a
L018
TPS35
TIP15T
HKY35R
CBDP
LF
CBDP
LF
BD
66.7
DCON
KWW
DCCB
DC
DCX
Fig.5
Extra Fine Pitch
Order Number
Stock Number
R of Teeth
L8
CBDP
LF
DCCB
DC
DCX
APMX
KAPR :45
GAMP :+20 +23 T :+449 +953
GAMF :-13 -10 I :+2255 +2302
45
BD
177.8 (315 only)
22 (315 only)
101.6
DCON
18
KWW
200
250
315

Dimensions(mm)
DC
DCX
45
LF DCON CBDP DAH
DCCB
BD
KWW
L8
WT
(kg)
APMX
(mm)
Type
(Fig.)
ASX445-050A03R
50
63.0
40
22
20
11
45
10.4
6.3
0.5
ASX445-063A04R
63
75.9
40
22
20
11
50
10.4
6.3
0.7
ASX445-080A04R
80
93.2
50
27
23
13
56
12.4
1.0
ASX445-100A05R
100
113.2
50
32
26
17
70
14.4
1.6
ASX445-125B06R
125
138.0
63
40
32
56
80
16.4
2.4
ASX445-160C07R
160
173.0
63
40
29
56
100
16.4
3.9
ASX445-200C08R
200
212.9
63
60
32
135
155
25.7
14.22
6.7
ASX445-250C10R
10
250
262.9
63
60
32
174
200
25.7
14.22
10.5
ASX445-315C14R
14
315
327.9
80
60
57
256.8
285
25.7
14.22
22.4
ASX445-050A04R
50
63.0
40
22
20
11
45
10.4
6.3
0.4
ASX445-063A05R
63
75.9
40
22
20
11
50
10.4
6.3
0.6
ASX445-080A06R
80
93.2
50
27
23
13
56
12.4
0.9
ASX445-100A07R
100
113.2
50
32
26
17
70
14.4
1.5
ASX445-125B08R
125
138.0
63
40
32
56
80
16.4
2.3
ASX445-160C10R
10
160
173.0
63
40
29
56
100
16.4
3.6
ASX445-200C12R
12
200
212.9
63
60
32
135
155
25.7
14.22
5.8
ASX445-250C14R
14
250
262.9
63
60
32
174
200
25.7
14.22
10.6
ASX445-315C18R
18
315
327.9
80
60
57
256.8
285
25.7
14.22
22.2
ASX445-050A05R
50
63.0
40
22
20
11
45
10.4
6.3
0.4
ASX445-063A06R
63
75.9
40
22
20
11
50
10.4
6.3
0.6
ASX445-080A08R
80
93.2
50
27
23
13
56
12.4
0.9
ASX445-100A10R
10
100
113.2
50
32
26
17
70
14.4
1.5
ASX445-125B12R
12
125
138.0
63
40
32
56
80
16.4
2.3
ASX445-160C16R
16
160
173.0
63
40
29
56
100
16.4
3.6
ASX445-200C20R
20
200
212.9
63
60
32
135
155
25.7
14.22
6.5
ASX445-250C24R
24
250
262.9
63
60
32
174
200
25.7
14.22
10.3
ASX445-315C28R
28
315
327.9
80
60
57
256.8
285
25.7
14.22
21.8
MILLING
Fine Pitch
Coarse Pitch
Type
y ARBOR TYPE
DCCB
DC
DCX
Over 80
45
APMX
45
CBDP
LF
160
APMX
DAH
DC
DCX
Fig.4
50, 63
BD
DCON
KWW
L8
125
L8
45
Fig.3
BD
DCON
KWW
APMX
L8
CBDP

DAH
DC
DCX
APMX
For metric arbor
80
100
L8
Fig.2
BD
DCON
KWW
50
63
LF
Fig.1
WT : Tool Weight
SPARE PARTS
TECHNICAL DATA
P001
Q001
L019
DCON
DCX
DC
INDEXABLE MILLING
45
APMX
LH
y SHANK TYPE
Order Number
LF

Stock Number
R of Teeth
Dimensions(mm)
DC
DCX
LF
DCON
LH
APMX
(mm)
ASX445R503S32
50
63.0
125
32
40
ASX445R634S32
63
75.9
125
32
40
ASX445R804S32
80
93.2
125
32
40
SPARE PARTS
z
Tool Holder
Number
Shim
x
*c
Shim Screw
Clamp Screw Wrench (Insert) Wrench (Shim)
Insert
ASX445
STASX445N WCS503507H
TPS35
TIP15T
HKY35R

Wrench
The ASX400 uses a TORXPLUS clamp screw. The attached wrench is for the exclusive use of
this screw. To ensure the effectiveness of TORXPLUS only use the attached wrench.
2. Hexagonal wrench The attached hexagonal wrench is for use with the seat and the shim. The wrench size is 3.5mm.
Spare Parts
Only use the original parts that were supplied when purchased. If other parts are used the performance and safety
can not be assured.
MILLING
1. Wrench
L020
: Inventory maintained in Japan. (10 inserts in one case) (CBN and PCD inserts are available in 1 piece in one case)

: Stable Cutting
: General Cutting
Stainless Steel
Non-ferrous Metal
Honing :
E : Round F : Sharp
S : Chamfer + Hone T : Chamfer

Hardened Steel
Coated
Shape
Order Number
JL Breaker
: Unstable Cutting
Cast Iron
Cermet Carbide Dimensions(mm)
Class
Honing
F7030
MC5020
N
MP6120 EW
N
MP6130 EW
N
MP7130 EW
N
MP7140 EW
N
MP9120 EW
N
MP9130 EW
VP15TF
VP30RT
NX4545
For Aluminium Alloy Roughing For Cast Iron MediumHeavy Cutting LightRough Cutting FinishLight Cutting Application
Work
Material
Steel
SEET13T3AGEN-JL
E E
HTi10
P
M
K
N
S
H
IC
Geometry
BS RE
RE
13.43.97 1.9 1.5
a a a a a a a a a
BS
RE
45
IC
JM Breaker SEMT13T3AGSN-JM M S
RE
13.43.97 1.9 1.5
20
S
BS
RE
45
IC
JH Breaker
SEMT13T3AGSN-JH M S
RE
13.43.97 1.9 1.5
a a a a a a a a a a
20
S
BS
RE
45
IC
FT Breaker
SEMT13T3AGSN-FT M S
BS
RE
13.43.97 1.9 1.5
20
S
RE
45
IC
JP Breaker
SEGT13T3AGFN-JP
G F
20
S
BS
13.43.97 2.2
45
IC
20
S
y Instructions for use of the JP breaker

JP breaker has sharp cutting edges.
* The
Wear gloves when handling.
MILLING
machining aluminium alloy, welding to the cutting edge tends to occur, often leading to insert failure. To prevent this, wet
* When
cutting is recommended.
MD220
W1
Geometry
BS RE
20
16.48 16.60 3.97 7.5 1.5
a
a
16.48 16.60 3.97 7.5 1.5
W1
WEEW13T3AGTR8C T
a a
Dimensions (mm)
R500
WEEW13T3AGER8C E
Carbide CBN PCD

MB710
Order Number
Coated
Cermet
HTi05T
Shape
Honing
MC5020
VP15TF
NX2525
Coated Cermet
VP25N
WIPER INSERTS
29
BS
RE
L
WEEW13T3AGTR3C T
a
a
16.48 16.60 3.97 3.0 1.5

W1
WEEW13T3AGFR3C F
16.48 16.60 3.97 3.0 1.5
29
RE
BS
L
inserts are single-cornered.

*Wiper
CBN grade MB710 is for cast iron.
*PCD grade MD220 is for aluminum alloy.
*Please refer to page L023 for notes when using wiper insert.
*
SPARE PARTS
TECHNICAL DATA
P001
Q001
L021
INDEXABLE MILLING
Work Material
Hardness
Mild Steel
< 180HB
180 280HB
Carbon Steel
Alloy Steel
280 350HB
M
Stainless Steel
K
Cast Iron
Ductile Cast Iron
MILLING
< 270HB
Tensile Strength
< 450MPa

Feed per Tooth (mm/t.) Breaker Feed per Tooth (mm/t.) Breaker Feed per Tooth (mm/t.) Breaker
Grade
Cutting Speed
(m/min)
F7030
280 (210 350)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
MP6120
VP15TF
250 (200 300)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
MP6130
240 (190 290)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
VP30RT
230 (180 280)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
NX4545
180 (130 230)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
F7030
250 (200 300)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
MP6120
VP15TF
220 (170 270)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
MP6130
200 (150 230)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
VP30RT
150 (120 180)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
NX4545
150 (120 180)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
F7030
180 (130 230)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
MP6120
VP15TF
140 (100 180)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
MP6130
120 (90 150)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
VP30RT
100 (80 160)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
NX4545
100 (80 160)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
MP7130
VP15TF
MP7140
VP30RT
220 (170 270)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
200 (150 250)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
NX4545
150 (120 180)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
MC5020
200 (150 250)
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
FT
VP15TF
180 (130 250)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
Tensile Strength
> 450MPa
MC5020
110 (80 150)
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
FT
Aluminium Alloy
HTi10
JP
0.2 (0.1 0.3)
JP
0.3 (0.2 0.4)
JP
Titanium Alloy

(Inconel718 etc.)
Hardened Steel
40 55HRC
650 (300 1000) 0.15 (0.10.2)
MP9120
VP15TF
50 (40 60)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
MP9130
45 (30 55)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
MP9120
VP15TF
40 (20 50)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
MP9130
35 (15 45)
0.15 (0.10.2)
JL
0.2 (0.1 0.3)
JM
0.3 (0.2 0.4)
JH
VP15TF
80 (60 100)
0.1 (0.050.15)
JL
0.15 (0.1 0.2) JM
0.2 (0.1 0.3)
JH
aRevolution (min-1)=(1000 x Cutting Speed)u(3.14 x DC) aTable Feed (mm/min)=Feed per Tooth x Number of Teeth x Cutter Revolution
L022
Fig.1
Fig.2
a These wiper inserts are single-cornered.

a Install the insert so that the cutting edge is located as shown in Fig., 1.
Do not install the wiper insert as shown in Fig. 2. (The insert may be damaged by a too heavy cutting load.)
a Recommended depth of cutting is ap=0.2-0.5(mm).
(Be aware of the cutting load if the depth of cut is over the recommendation.)
a The major cutting edge of a wiper insert is set more inside than a general tooth.
This is to prevent heavy loads on the wiper insert. (To prevent fracture set the feed under 0.2 mm/tooth)
a Excellent finished surface can be obtained with one wiper insert.
a When the feed per revolution is larger than the width of the wiper edge, install 2 or more wiper inserts equally inside the cutting
MILLING
body.
L023
INDEXABLE MILLING
RECOMMENDED CUTTING CONDITIONS WHEN USING A WIPER INSERT
Work Material
P
M
K
Grade

(m/min)
VP25N
200 (80 250)
VP15TF
180 (80 250)
VP15TF
120 270
MC5020
VP15TF
VP15TF
20 50
VP15TF
40 80
MILLING
aRecommended depth of cut (ap) is 0.2mm-0.5mm and feed per tooth (fz) is up to 0.2mm/t.
L024
130 250
FEATURES
y STABLE, LONG TOOL LIFE, HIGH ACCURACY BODY
A carbide shim with Mitsubishi's proprietary
Anti-Fly Insert (AFI) mechanism provides
excellent insert location characteristics,
permitting stable cutting even under high
load conditions.
The cutter body is made from a special

alloy that provides high strength at high
temperature. A special surface treatment
improves the corrosion resistance.
The ASX cutter uses screw-on type inserts

that allow easy clamping of the inserts with
high location precision. Indexing of the
inserts can be
performed without
completely
removing the screw.
y EFFECTIVE FOR VARIOUS MACHINING APPLICATIONS

a Coarse Pitch Type
1. The 1st recommendation
for cutting steel and
stainless steel.
2. For deep cutting and high
feed rates with largevolume chip discharge.
3. Longer overhang possible
for relatively low machining
riidity.
a Fine Pitch Type

type for cast iron,
hardened steel and
heat-resistant alloys.
2. For shallow cutting with
low feed rates and
low-volume chip
discharge.
a Extra Fine Pitch Type

for cast iron.
2. For cutting operations
where chip discharge
volume is small and
high table feed is
desired.
y CHIPBREAKERS FOR A WIDE RANGE OF APPLICATIONS
High accuracy insert with

ground-finished periphery.
Large rake angle leading
to low cutting resistance.
zWorkpiece rigidity is
low.
JM
Light to
Rough cutting
Breaker
High accuracy M class

insert. For a wide range
of workpiece materials
and cutting conditions.
zGeneral cutting.
JH
Medium to
Heavy cutting
Breaker
High accuracy M class

insert. Strong cutting
edge for high fracture
resistance.
zInterrupted cutting.
xScaling.
JP
Aluminium alloy
cutting
Breaker
FT
Rough cutting
for cast iron
Breaker
High accuracy insert with

High accurate M class
ground-finished periphery. Large
inserts. Higher fracturerake angle and mirror-finished rake resistant flat-top inserts.
face for sharp cutting performance
and high welding resistance.
zGeneral cutting of
aluminium alloy.
zFor rough machining

of scaled cast iron.
MILLING
JL
Finish to
Light cutting
Breaker
y INSERT GRADES FOR A WIDE RANGE OF MATERIALS
Low
Cutting
Speed
High
Carbon Steel
Alloy Steel
F7030
MP6120
VP15TF
MP6130
VP30RT
Cutting Unstable
Stable Conditions
Stainless Steel
F7030
MP7130
VP15TF
MP7140
VP30RT
Cutting Unstable
Stable Conditions
Cast Iron
Ductile Cast Iron
MC5020
Aluminium Alloy
HTi10
Heat Treated Steel
MP9120
VP15TF
VP15TF
MP9130
VP15TF
Cutting Unstable
Stable Conditions

Titanium Alloy
Cutting Unstable
Stable Conditions
Cutting Unstable
Stable Conditions
Cutting Unstable
Stable Conditions
(Note) When machining steel or stainless steel where the emphasis is on surface finish, use cermet grade NX4545.
Stable Cutting : Continuous cutting, Constant depth of cut, Pre-machined securely clamped component cutting
Unstable Cutting : Heavy interrupted, Irregular depth of cut, Low clamping rigidity cutting
L025
INDEXABLE MILLING
40
sided insert.
Fig. 3
200
18
CBDP
edge inserts.
40
BD
101.6
DCON
KWW
LF
L8
DCCB
DC
DCX
DCCB
DC
DCX
40
LF
DAH
DC
DCX
BD
DCON
KWW
L8
Heat Resistant Alloy Hardened Steel
a Heptagonal double
100
125
160
APMX
Fig. 2
CBDP
BD
DCON
KWW
APMX
K
Cast Iron
Fig. 1
63
80
CBDP
M
Stainless Steel
Roughing
APMX
P
Steel
Finishing
LF
<GENERAL CUTTING>
L8
FACE MILLING
AHX640S
Cutter Diameter
DC
&80
&100
&125
&160
Coolant Hole
Number of Teeth
DC
AHX640S-063A04AR
63
75.55 50 22
20
11
AHX640SR08004CA
80
92.55 50 25.4
26
13
AHX640SR10005DA
5 100 112.55 50 31.75
35
AHX640SR12506EA
6 125 137.55 63 38.1
42
AHX640SR16007FA
7 160 172.55 63 50.8
AHX640SR20008KN
AHX640S-063A05AR
*1
APMX
Stock
R
L8
(kg)
(mm)
50 10.4
6.3
0.7
1 CS5015060T TKY20T
56
9.5
1.1
1 CS5015060T TKY20T
45
70 12.7
1.7
2 CS5015060T TKY20T
56
80 15.9 10
3.0
2 CS5015060T TKY20T
43
72
100 19.1 11
4.9
2 CS5015060T TKY20T
8 200 212.55 63 47.625 35
140
175 25.4 14.22 8.2
3 CS5015060T TKY20T
63
75.55 50 22
20
11
50 10.4
6.3
0.6
1 CS5015060T TKY20T
AHX640SR08006CA
80
92.55 50 25.4
26
13
56
9.5
1.0
1 CS5015060T TKY20T
AHX640SR10007DA
7 100 112.55 50 31.75
35
45
70 12.7
1.5
2 CS5015060T TKY20T
AHX640SR12508EA
8 125 137.55 63 38.1
42
56
80 15.9 10
2.9
2 CS5015060T TKY20T
AHX640SR16010FA
10 160 172.55 63 50.8
43
72
100 19.1 11
4.7
2 CS5015060T TKY20T
AHX640SR20012KN
12 200 212.55 63 47.625 35
140
175 25.4 14.22 7.9
3 CS5015060T TKY20T
DCX
LF
Order Number
Dimensions (mm)
Torque (N m) : CS5015060T=5.0
*12 Clamp
WT : Tool Weight
*
L026
&200
HSC10030H
12035H
MBA16033H
20040H
24045H
WT 2
Fine Pitch
MILLING
Coarse Pitch
Type
KAPR :40 T :10 (When using the MK breaker insert)

GAMP :-6 T :20 (When using MP, MM breaker inserts)
GAMF :-5 I :+9+10
Geometry
Type (Fig.)
&63
Set Bolt
DCON CBDP DAH DCCB BD KWW
Clamp
Screw
Wrench
LF
LF
CBDP
APMX
40
18
DCCB
DC
DCX
APMX
The cutter bore diameter DCON is indicated in millimetre.
BD
101.6
DCON
KWW
LF
CBDP
For metric arbor
40
L8
200
14
DCCB
DC
DCX
L8
CBDP
DCCB
DC
DCX
Fig. 4
BD
66.7
DCON
KWW
160
LF
L8
40
L8
Fig. 3
100
125
APMX
DAH
DC
DCX
BD
DCON
KWW
Fig. 2
CBDP
63
80
APMX
BD
DCON
KWW
Fig. 1
40
&100
&125
&160
*
*
Coolant Hole
DC
AHX640S-063A04AR
63
75.55 50
22
20
11
AHX640S-080A04AR
80
92.55 50
27
23
13
AHX640S-100B05AR
5 100 112.55 50
32
32
AHX640S-125B06AR
6 125 137.55 63
40
AHX640S-160C07NR
7 160 172.55 63
AHX640S-200C08NR
AHX640S-063A05AR
AHX640S-080A06AR
Dimensions (mm)
*1
L8
(kg)
(mm)
50 10.4
6.3
0.7
1 CS5015060T TKY20T
56 12.4
1.1
1 CS5015060T TKY20T
45
78 14.4
1.7
2 CS5015060T TKY20T
42
56
89 16.4
3.1
2 CS5015060T TKY20T
40
29
56
120 16.4
5.4
3 CS5015060T TKY20T
8 200 212.55 63
60
32
140
175 25.7 14.22 7.8
4 CS5015060T TKY20T
63
75.55 50
22
20
11
50 10.4
6.3
0.6
1 CS5015060T TKY20T
80
92.55 50
27
23
13
56 12.4
1.0
1 CS5015060T TKY20T
AHX640S-100B07AR
7 100 112.55 50
32
32
45
78 14.4
1.6
2 CS5015060T TKY20T
AHX640S-125B08AR
8 125 137.55 63
40
42
56
89 16.4
3.0
2 CS5015060T TKY20T
AHX640S-160C10NR
10 160 172.55 63
40
29
56
120 16.4
5.2
3 CS5015060T TKY20T
AHX640S-200C12NR
12 200 212.55 63
60
32
140
175 25.7 14.22 7.5
4 CS5015060T TKY20T
Order Number
DCX
LF
APMX
Stock
R
Number of Teeth
&200
HSC10030H
12035H
MBA16033H
20040H
WT 2
Fine Pitch
Coarse Pitch
Type
KAPR :40 T :10 (When using the MK breaker insert)

GAMP :-6 T :20 (When using MP, MM breaker inserts)
GAMF :-5 I :+9 +10
Geometry
Type (Fig.)
&63
&80
Set Bolt
DCON CBDP DAH DCCB BD KWW
Clamp
Screw
Wrench
MILLING
Cutter Diameter
DC
1 Clamp Torque (N m) : CS5015060T=5.0

2 WT : Tool Weight
SPARE PARTS
TECHNICAL DATA
P001
Q001
L027
INDEXABLE MILLING
NNMU200708ZEN-MP M E
MK Breaker
R0.8
1
20
MM Breaker
NNMU200712ZER-MM M E
8.0
R.1.2
1
20
WP Breaker
WNEU2007ZEN7C-WP E E
Shape
8.0
7.1 R0.8
20
7.2
Order Number
NNMU200608ZEN-MK M E
a a a
General
HK Breaker
NNMU200608ZEN-HK M E
R0.8
1
20
6.55
R0.8
1
20
6.55
a a a
Strong Cutting Edge Type

WK Breaker
Geometry
7.4
MP Breaker
Geometry
Coated
Class
Horning
MC5020
VP15TF
VP20RT
Application
Order Number
For Cast Iron
Shape
Class
Horning
MC5020
MP7030
VP15TF
Coated
For Cast Iron
Wiper Insert
For Stainless Steel cutting General Cutting Application
INSERT
7.4 R0.8
20
6.55

y Dry cutting
Work Material
MILLING
Mild Steel
(ASTM A36,AISI 1010)
(AISI 1045,AISI 4140)
(AISI 4340)
(AISI 304,AISI 316)
(AISI 304LN,AISI 316LN)
(AISI 329)
Ferritic and Martensitic Stainless Steel
(AISI 410,AISI 430)
(AISI 431,AISI 420)
(AISI 630,AISI 631)
Gray Cast Iron

(AISI No 45 B)
Ductile Cast Iron

(FCD450)
Ductile Cast Iron

(AISI 100-70-03)
Hardened Steel
(AISI H13,AISI L6)
Tensile
Strength
Breaker
Insert Grade
Cutting Speed
Feed per Tooth
180HB
MP
VP15TF
250 (200300)
0.3 (0.20.4)
180 280HB
MP
VP15TF
220 (170250)
0.3 (0.20.4)
280 350HB
MP
VP15TF
140 (100 180)
0.3 (0.20.4)
200HB
MM
MP7030
200 (150250)
0.2 (0.10.3)
>200HB
MM
MP7030
150 (100 200)
0.2 (0.10.3)
280HB
MM
MP7030
140 (100 180)
0.15 (0.050.25)
200HB
MM
MP7030
200 (150250)
0.2 (0.10.3)
>200HB
MM
MP7030
150 (100200)
0.2 (0.10.3)
<450HB
MM
MP7030
130 (100 160)
0.15 (0.050.25)
MK,HK
MC5020
220 (150300)
0.3 (0.20.4)
MP,MK,HK
VP15TF
180 (130 230)
0.3 (0.20.4)
MK,HK
MC5020
200 (150250)
0.2 (0.10.3)
MP,MK,HK
VP15TF
170 (120 220)
0.2 (0.10.3)
MK,HK
MC5020
170 (150 200)
0.2 (0.1 0.3)
MP,MK,HK
VP15TF
140 (100180)
0.2 (0.10.3)
MP
VP15TF
80 (60 100)
0.15 (0.10.2)
Tensile Strength
350MPa
Tensile Strength
450MPa
Tensile Strength
800MPa
40 55HRC
(m/min)
(mm/t.)
Axial depth of cut

ap (mm)
(Note 1) Recommend wet cutting for good surface finishing of stainless steel. (Tool life is short compared to wet cutting.)
(Note 2) When clamp rigidity is low and tool is overhanged, we recommend to adjust the cutting speed and feed 70% to 80% than the conditon above.
L028
y Wet cutting
Tensile
Strength
Breaker
Insert Grade
Cutting Speed
Feed per Tooth

(AISI 304,AISI 316)
(AISI 304LN,AISI 316LN)
(AISI 329)
(AISI 410,AISI 430)
(AISI 431,AISI 420)
(AISI 630,AISI 631)
Titanium Alloy
(Ti-6A-4V)
200HB
MM
MP7030
125 (100 150)
0.15 (0.10.2)
>200HB
MM
MP7030
100 (75 125)
0.15 (0.10.2)
280HB
MM
MP7030
80 (60 100)
0.10 (0.050.15)
200HB
MM
MP7030
125 (100 150)
0.15 (0.10.2)
>200HB
MM
MP7030
100 (75 125)
0.15 (0.10.2)
<450HB
MM
MP7030
70 (50 90)
0.1 (0.05 0.15)
MM
MP7030
40 (2050)
0.15 (0.10.2)

(Inconel718)
MM
MP7030
40 (20 50)
0.15 (0.10.2)
Work Material
(m/min)
(mm/t.)
Axial depth of cut

ap (mm)
(Note) With low workpiece clamping rigidity or long overhang of the tool, adjust cutting speed and feed to 70 or 80 % of the recommended
conditons above.
y Cutting Condition with Wiper insert
Mild Steel
(ASTM A36,AISI 1010)
(AISI 1045,AISI 4140)
(AISI 4340)
Gray Cast Iron

(AISI No 45 B)
Ductile Cast Iron

(FCD450)
Tensile
Strength
Main
Wiper
Insert Grade Insert Grade
Cutting Speed
Feed per Tooth
(m/min)
(mm/t.)
Axial depth of cut

ap (mm)
180HB
MP
VP15TF
WP
VP15TF
250 (200300)
0.3 (0.20.4)
0.5
180 280HB
MP
VP15TF
WP
VP15TF
220 (170270)
0.3 (0.20.4)
0.5
280 350HB
MP
VP15TF
WP
VP15TF
140 (100 180)
0.3 (0.20.4)
0.5
MK,HK MC5020
WK
MC5020
320 (250 400)
0.3 (0.2 0.4)
0.5
VP15TF
WP
VP15TF
220 (150300)
0.3 (0.20.4)
0.5
MK,HK MC5020
WK
MC5020
250 (200300)
0.2 (0.10.3)
0.5
VP15TF
WP
VP15TF
200 (150250)
0.2 (0.10.3)
0.5
MK,HK MC5020
WK
MC5020
220 (200250)
0.2 (0.1 0.3)
0.5
MP
VP15TF
WP
VP15TF
170 (150200)
0.2 (0.10.3)
0.5
Tensile Strength
350MPa
Tensile Strength
450MPa
MP
MP
(AISI 100-70-03)
Tensile Strength
800MPa
MP
VP15TF
WP
VP15TF
40 (2050)
0.15 (0.10.2)
0.5
Hardened Steel
(AISI H13,AISI L6)
40 55HRC
MP
VP15TF
WP
VP15TF
80 (60100)
0.15 (0.10.2)
0.5
Ductile Cast Iron
(Note) With low workpiece clamping rigidity or long overhang of the tool, adjust cutting speed and feed to 70 or 80 % of the recommended
conditons above.
SPARE PARTS
TECHNICAL DATA
P001
Q001
MILLING
Work Material
L029
INDEXABLE MILLING
Type
Extra Fine Pitch Type
Super Extra Fine Pitch Type
Stock Number
R L of Teeth DC
AHX640WR/L08008C
a a
AHX640WR/L10010D
a a
10
AHX640WR/L12512E
a a
AHX640WR/L16016F
80
177.8
315 101.6
DCON
KWW
40
L8
APMX
22
DCCB
DC
DCX
40

Dimensions(mm)
DCX
18
L8
18
DCCB
DC
DCX
KAPR :40
GAMP :-6 T :+10
GAMF :-4 I :+9 +10 (T,I : When using the MK breaker insert)
Order Number
Fig.4 BD
BD
101.6
DCON
KWW
CBDP
200
250
40
CBDP
LF
Fig.3
APMX
sided insert.
edge inserts.
DCCB
DC
DCX
LF
a Heptagonal double
40
L8
DAH
DC
DCX
APMX
Cast Iron
LF
BD
DCON
KWW
Fig.2
100
125
160
APMX
BD
DCON
KWW
Fig.1
80
CBDP
Roughing
LF
Finishing
L8
<HIGH FEED CUTTING FOR CAST IRON>
CBDP
FACE MILLING
AHX640W
LF
DCON CBDP DAH DCCB
KWW
L8
WT
(kg)
APMX
(mm)
Type
(Fig.)
26
13
56
9.5
1.5
100 112.6 50 31.75
32
45
70
12.7
2.1
12
125 137.6 63 38.1
35
56
80
15.9 10
3.5
a a
16
160 172.6 63 50.8
38
72
100
19.1 11
5.6
AHX640WR/L20020K
a a
20
200 212.6 63 47.625
35
140
175
25.4 14.22
9.0
AHX640WR/L25024K
a a
24
250 262.6 63 47.625
35
180
220
25.4 14.22
14.4
AHX640WR/L31528P
a a
28
315 327.6 63 47.625
40
225
285
25.4 14.22
23.8
AHX640WR/L08010C
a a
10
26
13
56
9.5
1.5
AHX640WR/L10014D
a a
14
100 112.6 50 31.75
32
45
70
12.7
2.1
AHX640WR/L12518E
a a
18
125 137.6 63 38.1
35
56
80
15.9 10
3.5
AHX640WR/L16022F
a a
22
160 172.6 63 50.8
38
72
100
19.1 11
5.6
AHX640WR/L20028K
a a
28
200 212.6 63 47.625
35
140
175
25.4 14.22
9.0
AHX640WR/L25036K
a a
36
250 262.6 63 47.625
35
180
220
25.4 14.22
14.4
AHX640WR/L31544P
a a
44
315 327.6 63 47.625
40
225
285
25.4 14.22
23.8
80
92.6 50 25.4
BD
92.6 50 25.4
INSERTS

y GENERAL CUTTING
Coated
Shape
Order Number
Class
Honing
MC5020
VP15TF
VP20RT
MILLING
* WT : Tool Weight
MK Breaker NNMU200608ZEN-MK M E
Geometry
Work Material
a a a
Gray
Cast Iron
Tensile
Strength
Grade
MC5020
< 350MPa
VP15TF
VP20RT
MC5020
R0.8
1
20
General
HK Breaker NNMU200608ZEN-HK M E
Ductile
Cast Iron
6.55
7.4
Work Material
6.55
L030
Grade
0.3
(0.2 0.4)
0.3
(0.2 0.4)
0.2
(0.1 0.3)
0.2
(0.1 0.3)
0.2
(0.1 0.3)
0.2
(0.1 0.3)
Axial Depth of Cut Cutting Speed Feed per Tooth

(m/min)
(mm)
(mm/t.)
< 0.5
Gray
Cast Iron
0.53
MC5020
Ductile
Cast Iron
a
VP15TF
VP20RT
220
(150300)
180
(130250)
200
(150250)
170
(120220)
170
(150200)
140
(100180)
y FINISHING (USE OF WIPER INSERTS)
K
7.4 R0.8
20
VP15TF
VP20RT
MC5020
< 800MPa
R0.8
1
20
6.55
a a a

Wiper
< 450MPa
Cutting Speed Feed per Tooth

(m/min)
(mm/t.)
< 0.5
0.53
320
(250400)
270
(200350)
270
(200350)
220
(200250)
0.2
(0.1 0.3)
*Please use 2-3 pcs of Wiper inserts in case of 'over 6mm/rev'.
CBDP
DCCB
DC
DCX
Type
Extra Fine Pitch Type
Super Extra Fine Pitch Type
Stock Number
R L of Teeth
40
APMX
LF
CBDP
22
L8
BD
177.8 (315 only)
101.6
18
DCON
KWW
DCCB
DC
DCX
APMX

KAPR :40
GAMP :-6 T :+10
GAMF :-4 I :+9 +10 (T,I : When using the MK breaker insert)
200
250
315
40
CBDP
LF
14
For metric arbor
Order Number
LF
L8
DCCB
DC
DCX
Fig.4
BD
66.7
DCON
KWW
BD
DCON
KWW
40
APMX
160
APMX
CBDP
Fig.3
40
L8
DAH
DC
DCX
100
125
L8
Fig.2
BD
DCON
KWW
80
LF
Fig.1

Dimensions(mm)
DCX
80
92.6
50
27
23
13
BD
KWW
L8
WT
(kg)
APMX
(mm)
Type
(Fig.)
56
12.4
1.5
LF DCON CBDP DAH DCCB
DC
AHX640W-080A08R/L
a a
AHX640W-100B10R/L
a a
10
100 112.6
50
32
32
45
70
14.4
2.1
AHX640W-125B12R/L
a a
12
125 137.6
63
40
32
56
80
16.4
3.1
AHX640W-160C16R/L
a a
16
160 172.6
63
40
29
56
100
16.4
5.6
AHX640W-200C20R/L
a a
20
200 212.6
63
60
32
135
155
25.7
14
8.0
AHX640W-250C24R/L
a a
24
250 262.6
63
60
32
180
200
25.7
14
12.6
AHX640W-315C28R/L
a a
28
315 327.6
80
60
57
225
285
25.7
14
31.5
AHX640W-080A10R/L
a a
10
92.6
50
27
23
13
56
12.4
1.5
AHX640W-100B14R/L
a a
14
100 112.6
50
32
32
45
70
14.4
2.1
AHX640W-125B18R/L
a a
18
125 137.6
63
40
32
56
80
16.4
3.1
AHX640W-160C22R/L
a a
22
160 172.6
63
40
29
56
100
16.4
5.6
AHX640W-200C28R/L
a a
28
200 212.6
63
60
32
135
155
25.7
14
8.0
AHX640W-250C36R/L
a a
36
250 262.6
63
60
32
180
200
25.7
14
12.6
AHX640W-315C44R/L
a a
44
315 327.6
80
60
57
225
285
25.7
14
31.5
80
MILLING
* WT : Tool Weight
SPARE PARTS
*
Tool Holder
Number
AHX640W Type
Wedge
Clamp Screw
Wrench
CWAHX640WN
LS0622T
TKY15T
* Clamp Torque (N m) : LS0622T=6.0
SPARE PARTS
TECHNICAL DATA
P001
Q001
L031
INDEXABLE MILLING
FACE MILLING
AOX445
<HIGH EFFICIENCY CUTTING FOR CAST IRON>
AOX445-063A04R
AOX445-R08006C
AOX445-R10008D
AOX445-R12510E
AOX445-R16012F
R
a
a
a
a
a
T :-9 -6
I :-5
45
DCCB
DC
DCX
Right hand (R) only for the standard.

Dimensions(mm)
DC
4
6
8
10
12
45
DCX
LF DCON CBDP DAH DCCB BD KWW
63 70.8 40
80 87.8 50
100 107.8 50
125 132.8 63
160 167.8 63
22
25.4
31.75
38.1
50.8
20
26
32
35
38
11
38
45
60
80
50
60
70
80
100
10.4
9.5
12.7
15.9
19.1
WT
(kg)
L8
6.3
6
8
10
11
0.6
1.2
1.8
3.0
4.9
Max.
Allowable Type
Revolution (Fig.)
A1
-1
(mm) (mm) (min )
APMX
Type
Coarse Pitch
Stock
Order Number
Number
of Teeth
y ARBOR TYPE
KAPR :45
GAMP :-5
GAMF :-9 -6
DAH
DC
DCX
CBDP
inserts.
(when the depth of cut is 3mm)
a For high efficiency roughing
through to finishing.
a Easy operation and cleansing.
A1
a Economical 16 cutting edge
BD
DCON
KWW
80
100
125
160
LF
sided insert.
Fig.2
BD
DCON
KWW
APMX
63
L8
Fig.1
a Solid CBN octagonal double
A1
CBDP
LF
K
Cast Iron
APMX
Roughing
L8
Finishing
3
3
3
3
3
8
8
8
8
8
12000
11000
9300
8300
7200
1
2
2
2
2
(Note) When machining with a depth of cut of 8mm, 16 corners cannot be used.
WT : Tool Weight
DCX
DC
DCON
45
A1
AOX445R503S32
AOX445R634S32
Dimensions(mm)
Number
of Teeth
Type
Order Number
LF
Right hand (R) only for the standard.

Stock
Coarse Pitch
MILLING
y SHANK TYPE
APMX
LH
DC
DCX
LF
DCON
LH
3
4
50
63
57.8
70.8
125
125
32
32
40
40
a
a
WT
(kg)
1.1
1.4
A1
APMX
(mm)
(mm)
Max.
Allowable
Revolution
(min-1)
3
3
8
8
13000
12000
* WT : Tool Weight
SPARE PARTS
*
Tool Holder
Number
AOX445
Wedge
Clamp Screw
Wrench
CWAOX445N
LS15T
TKY25T
Clamp Torque (N m) : LS15T=8.0
INSERTS
SL-ONEN120404ASN
BC5030
Order Number
Class
CBN
Work Material
Geometry
Gray
Cast Iron
Tensile
Strength
Grade

(m/min)
(mm/t.)
BC5030
1000
(8001500)
< 200MPa
250 350
MPa
Note) Dry cutting is recommended.

12.7
L032
R0.4
4.76
: Inventory maintained in Japan. (CBN inserts are available in 1 piece in one case.)
0.1
(0.050.15)
FACE MILLING
SG20
<CUTTING FOR DIFFICULT-TO-CUT MATERIALS>
H
Hardened Steel
Fig.2
DCON
KWW
LF
125
160
LF
a High rake angle.
DCON
KWW
80
100
L8
CBDP
Fig.1
DAH
DC
DCX
with a strong cutting

edge.
a Suitable for difficultto-cut materials.
DCCB
DC
DCX
APMX
K
Cast Iron
L8
CBDP
M
Stainless Steel
Roughing
APMX
P
Steel
Finishing
GAMP :+24 T :+23 (KAPR=45)

GAMF :+9
Stock Number
R of Teeth
Order Number
DCX
LF
DCON
CBDP DAH DCCB KWW
L8
WT
(kg)
1.5
APMX
(mm)
Type
(Fig.)
SG20R0304C
80
101.2
50
25.4
26
13
SG20R0405D
100
121.4
63
31.75
32
17
12.7
2.9
SG20R0506E
125
146.4
63
38.1
38
60
15.9
10
3.8
SG20R0608F
160
181.4
63
50.8
38
80
19.1
11
6.1
9.5
WT : Tool Weight
Order Number
RGEN2004M0SN
RGEN2004M0EN
F7030
VP15TF
UP20M
UTi20T
HTi10
Coated Carbide
Work Material
Hardness
Cutting
Speed
(m/min)
Grade
Geometry
VP15TF
< 180HB
a a a
NX2525
Carbon Steel
Alloy Steel
20.00
4.76
VP15TF
280 350HB
30
NX2525
Stainless
Steel
< 200HB
VP15TF
Feed per Recommended

Max. Depth
Tooth
of Cut
(mm/t.)
(mm)
180
(100250)
175
(150200)
180
(100250)
165
(130200)
0.35
(0.20.5)
0.25
(0.20.3)
0.3
(0.20.4)
0.25
(0.20.3)
4.5
150
(100200)
0.35
(0.20.5)
4.5
4.5
4.5
K Gray Cast Iron Tensile Strength VP15TF ( 160 ) ( 0.4 )

100220
0.30.5
< 350MPa
H Hardened Steel 4060HRC VP15TF ( 80 ) ( 0.2 )
50100
0.10.3
4.5
2
MILLING
INSERTS
Class
Dimensions(mm)
DC
-1)
a Revolution (min =(1000 x Cutting Speed)u(3.14 x DC)

a Table Feed (mm/min)
=Feed per Tooth x Number of Teeth x Cutter Revolution
SPARE PARTS
z
Tool Holder
Number
Locator
Insert
SG20R0304C
SG20R0405D
SG20R0506E
SG20R0608F
Wedge-T
Wedge-S
SPSG20R CWSG20TR CWSG20SN
Clamp Screw
LS15T
Wrench
TKY25T
Set Bolt
HSC16035
SPARE PARTS
TECHNICAL DATA
P001
Q001
L033
INDEXABLE MILLING
Finishing
H
Fig.1
DCON
KWW
Fig.2
DCON
KWW
125
160
LF
100
L8
N
Non-ferrous Metal
CBDP
LF
K
Cast Iron
a High rake angle.
a High rigidity due
DAH
DC
DCX
to carbide shim.
15
DCCB
15
DC
DCX
APMX
M
Stainless Steel
CBDP
P
Steel
Roughing
L8
<HEAVY CUTTING>
APMX
FACE MILLING
SE515
Type
KAPR :15
GAMP :+19 T :+11
GAMF :+5 I :+17
Close Pitch Coarse Pitch
Stock Number
R of Teeth
Order Number
Dimensions(mm)
DC
DCX
LF
DCON
CBDP DAH DCCB KWW
L8
WT
(kg)
APMX
(mm)
Type
(Fig.)
SE515R0405D
100
108.9
63
31.75
32
17
12.7
2.3
11.5
SE515R0506E
125
133.6
63
38.1
38
60
15.9
10
3.5
11.5
SE515R0608F
160
168.3
63
50.8
38
80
19.1
11
5.6
11.5
SE515R0407D
100
108.9
63
31.75
32
17
12.7
2.3
11.5
SE515R0509E
125
133.6
63
38.1
38
60
15.9
10
3.5
11.5
SE515R0611F
11
160
168.3
63
50.8
38
80
19.1
11
5.6
11.5
WT : Tool Weight
SPARE PARTS
x
Insert
Tool Holder
Number
Locator
SE515R0405D
0407D
SE515R0506E
Wedge-T
Wedge-S
Clamp
Wrench Set Bolt
Screw
HSC16035
SPSE515R
STSE515R CWSE545TR CWSE545SN LS15T TKY25T
Shim
MILLING
SE515R0611F

Work
Material
Hardness
Grade

(m/min)
(mm/t.)
200
(160 250)
180
(100 250)
140
(80 200)
200
(160 250)
180
(100 250)
140
(80 200)
120
(80 160)
F7030
Mild Steel
< 180HB
VP15TF
NX4545
F7030

Alloy Steel
280 350HB
NX4545
VP15TF

L034
VP15TF
0.2
(0.10.3)
Work
Material
M Stainless
Steel
Cast Iron
Hardness
Grade
< 200HB
VP15TF
Tensile
Strength
MC5020
< 450MPa
0.2
(0.10.3)
0.15
(0.1 0.2)
N Aluminium
Alloy
VP15TF
MD220
HTi10

(m/min)
(mm/t.)
0.2
(0.10.3)
150
(100200)
175
(100 250)
160
(100 220)
1000
(200 1500)
650
(300 1000)
0.2
(0.10.3)
0.15
(0.05 0.25)
0.12
(0.05 0.2)
a Revolution (min-1)=(1000 x Cutting Speed)u(3.14 x DC)

INSERTS
P
M
K
N
Steel

: Stable Cutting
: General Cutting
Stainless Steel
Cast Iron
Non-ferrous Metal
Order Number
Class
Honing
F7030
MC5020
VP15TF
Coated
Shape
: Unstable Cutting
Honing :
SECN1504EFTR1
C T
SEEN1504EFER1
E E
SEEN1504EFTR1
E T
SEEN1504EFSR1
E S
SEKN1504EFTR1
K T
SEKN1504EFSR1
K S
Cermet Carbide
Dimensions(mm)
NX2525
NX4545
UTi20T
HTi10
Work
Material
a
a
a
a
a
a
IC
BS
RE
15.875 4.76 1.4
1.0
15.875 4.76 1.4
1.0
15.875 4.76 1.4
1.0
15.875 4.76 1.4
1.0
15.875 4.76 1.4
15.875 4.76 1.4
Geometry
BS
RE
20
15
IC
WIPER INSERTS
WEC53EFTR5C
C T
W1
15.875 16.903
RE
4.76
1.0
Geometry
R500
RE
RE
15
5
20
S
MILLING
Order Number
Dimensions(mm)
W1
Shape
Class
Honing
NX2525
Cermet
SPARE PARTS
TECHNICAL DATA
P001
Q001
L035
INDEXABLE MILLING
SHOULDER MILLING
VOX400
<FOR CAST IRON>

edge inserts.
a Screw-on type.
Fig.3
CBDP
200
250
DB
101.6
DCON
KWW
y ARBOR TYPE
50 40 22
20
11
VOX400-063A04R
63 40 22
20
VOX400R08004C
80 50 25.4
VOX400R10006D
VOX400R12508E
VOX400R16010F
WT APMX
(kg) (mm)
*1
Clamp
Screw
Wrench
CS401160T
TKY15T
10
CS401160T
TKY15T
1.0
10
CS401160T
TKY15T
1.5
10
CS401160T
TKY15T
80
15.9 10
2.7
10
CS401160T
TKY15T
80
120
19.1 11
5.3
10
CS401160T
TKY15T
130
175
25.4 14.22
8.5
10
CS401160T
TKY15T
35
180
220
25.4 14.22 13.3
10
CS401160T
TKY15T
50 40 22
20
11
17
41
10.4
6.3
0.3
10
CS401160T
TKY15T
63 40 22
20
11
17
50
10.4
6.3
0.6
10
CS401160T
TKY15T
80 50 25.4
26
13
20
55
9.5
1.0
10
CS401160T
TKY15T
10 100 50 31.75
32
45
70
12.7
1.5
10
CS401160T
TKY15T
12 125 63 38.1
40
60
80
15.9 10
2.7
10
CS401160T
TKY15T
VOX400R16016F
16 160 63 50.8
43
80
120
19.1 11
5.3
10
CS401160T
TKY15T
VOX400R20020K
20 200 63 47.625
35
130
175
25.4 14.22
8.5
10
CS401160T
TKY15T
VOX400R25024K
24 250 63 47.625
35
180
220
25.4 14.22 13.3
10
CS401160T
TKY15T
VOX400-063A08R
63 40 22
20
11
17
50
10.4
VOX400R08010C
10
80 50 25.4
26
13
20
55
VOX400R10012D
12 100 50 31.75
32
45
VOX400R12516E
16 125 63 38.1
40
VOX400R16020F
20 160 63 50.8
43
VOX400R20026K
26 200 63 47.625
VOX400R25034K
34 250 63 47.625
BD
KWW
L8
17
41
10.4
6.3
0.3
10
11
17
50
10.4
6.3
0.6
26
13
20
55
9.5
6 100 50 31.75
32
45
70
12.7
8 125 63 38.1
40
60
10 160 63 50.8
43
VOX400R20012K
12 200 63 47.625
35
VOX400R25016K
16 250 63 47.625
VOX400-050A05R
VOX400-063A06R
VOX400R08008C
VOX400R10010D
VOX400R12512E
DC
1 Clamp Torque (N m) : CS401160T=3.5

2 WT : Tool Weight
L036
*2
Dimensions(mm)
Type(Fig.)
Stock
Number of Teeth
VOX400-050A03R
Type
Coarse Pitch
Fine Pitch
Extra Fine Pitch
MILLING
*
*
Order Number
APMX
DCCB
DC
LF
L8
DCCB
DC
L8
DAH
DCCB
DC
BD
DCON
KWW
L8
100
125
160
CBDP
LF
Fig.2
APMX
Cast Iron
BD
DCON
KWW
LF
50
63
80
CBDP
Fig.1
APMX
Roughing
6.3
0.5
10
CS401160T
TKY15T
9.5
1.0
10
CS401160T
TKY15T
70
12.7
1.4
10
CS401160T
TKY15T
60
80
15.9 10
2.6
10
CS401160T
TKY15T
80
120
19.1 11
5.1
10
CS401160T
TKY15T
35
130
175
25.4 14.22
8.2
10
CS401160T
TKY15T
35
180
220
25.4 14.22 13.0
10
CS401160T
TKY15T
DCCB
DC
LF
APMX
DCCB
DC
L8
CBDP
CBDP
LF
LF
BD
101.6(160:66.7)
DCON
KWW
160
200
250
APMX
DAH
DCCB
DC
Fig.3
BD
DCON
KWW
L8
L8
100
125
APMX
50
63
80
Fig.2
BD
DCON
KWW
CBDP
Fig.1
For metric arbor

50 40
22
20
11
VOX400-063A04R
63 40
22
20
11
VOX400-080A04R
80 50
27
23
VOX400-100B06R
6 100 50
32
VOX400-125B08R
8 125 63
VOX400-160C10R
VOX400-200C12R
WT APMX
(kg) (mm)
*1
Type(Fig.)
Number of Teeth
VOX400-050A03R
Stock
R
Order Number
*2
Dimensions(mm)
Clamp
Screw
Wrench
CS401160T
TKY15T
CS401160T
TKY15T
10
CS401160T
TKY15T
1.7
10
CS401160T
TKY15T
10
CS401160T
TKY15T
5.4
10
CS401160T
TKY15T
8.1
10
CS401160T
TKY15T
25.7 14.22 11.8
10
CS401160T
TKY15T
41
10.4
6.3
0.3
10
CS401160T
TKY15T
17
50
10.4
6.3
0.6
10
CS401160T
TKY15T
13
20
56
12.4
10
CS401160T
TKY15T
32
45
78
14.4
1.7
10
CS401160T
TKY15T
40
32
56
89
16.4
10
CS401160T
TKY15T
16 160 63
40
29
56
120
16.4
5.4
10
CS401160T
TKY15T
20 200 63
60
32
130
175
25.7 14.22
8.1
10
CS401160T
TKY15T
VOX400-250C24R
24 250 63
60
32
180
210
25.7 14.22 11.8
10
CS401160T
TKY15T
VOX400-063A08R
63 40
22
20
11
17
50
10.4
6.3
0.5
10
CS401160T
TKY15T
VOX400-080A10R
10
80 50
27
23
13
20
56
12.4
1.0
10
CS401160T
TKY15T
VOX400-100B12R
12 100 50
32
32
45
78
14.4
1.6
10
CS401160T
TKY15T
VOX400-125B16R
16 125 63
40
32
56
89
16.4
2.8
10
CS401160T
TKY15T
VOX400-160C20R
20 160 63
40
29
56
120
16.4
5.2
10
CS401160T
TKY15T
VOX400-200C26R
26 200 63
60
32
130
175
25.7 14.22
7.9
10
CS401160T
TKY15T
VOX400-250C34R
34 250 63
60
32
180
210
25.7 14.22 11.5
10
CS401160T
TKY15T
DC
BD
KWW
L8
17
41
10.4
6.3
0.3
10
17
50
10.4
6.3
0.6
10
13
20
56
12.4
32
45
78
14.4
40
32
56
89
16.4
10 160 63
40
29
56
120
16.4
12 200 63
60
32
130
175
25.7 14.22
VOX400-250C16R
16 250 63
60
32
180
210
VOX400-050A05R
50 40
22
20
11
17
VOX400-063A06R
63 40
22
20
11
VOX400-080A08R
80 50
27
23
VOX400-100B10R
10 100 50
32
VOX400-125B12R
12 125 63
VOX400-160C16R
VOX400-200C20R
MILLING
Extra Fine Pitch
Fine Pitch
Coarse Pitch
Type
y ARBOR TYPE
Torque (N m) : CS401160T=3.5
*12 Clamp
WT : Tool Weight
*
WIPER INSERT
SONX1206PER
N E
Geometry
Shape
Order Number
WOEX1206PER5C E E
a a
Geometry
12.5
13.025
Order Number
Coated
VP15TF
Shape
Class
Horning
MC5020
VP15TF
Coated
Class
Horning
INSERT
12.7
6.3
5.5
L037
INDEXABLE MILLING

y VOX400 (Standard pitch)
Work Material
Tensile
Strength
< 200MPa
Gray Cast Iron

< 350MPa
< 450MPa
Ductile Cast Iron

< 800MPa
Speed
Insert Grade Cutting
(m/min)
& 50 & 250

Radial Depth of Cut
Depth of Cut
Feed per Tooth
ap (mm)
ae (mm)
fz (mm/tooth)
MC5020
300(250 350)
< DC
< 10
0.4(0.3 0.5)
VP15TF
250(200 300)
< DC
< 10
0.4(0.3 0.5)
MC5020
220(150 300)
< DC
< 10
0.3(0.2 0.4)
VP15TF
200(150 300)
< DC
< 10
0.3(0.2 0.4)
MC5020
200(150 250)
< DC
< 10
0.3(0.2 0.4)
VP15TF
170(150 200)
< DC
< 10
0.3(0.2 0.4)
MC5020
170(150 200)
< DC
< 10
0.2(0.1 0.3)
VP15TF
150(100 200)
< DC
< 10
0.2(0.1 0.3)
y VOX400 (Fine pitch)

Work Material
Tensile
Strength
< 200MPa
Gray Cast Iron

< 350MPa
< 450MPa
Ductile Cast Iron

< 800MPa
Work Material
Tensile
Strength
< 200MPa
MILLING
Gray Cast Iron

< 350MPa
< 450MPa
Ductile Cast Iron

< 800MPa
Work Material
Tensile
Strength
< 200MPa
Gray Cast Iron

< 350MPa
< 450MPa
Ductile Cast Iron

< 800MPa
Speed
(m/min)
& 50,& 63
& 80
Radial Depth of Cut Depth of Cut Feed per Tooth Radial Depth of Cut Depth of Cut Feed per Tooth
ae (mm)
ap (mm)
fz (mm/t.)
ae (mm)
ap (mm)
fz (mm/t.)
MC5020
300(250 350)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
VP15TF
250(200 300)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
MC5020
220(150 300)
< DC
< 10
0.3(0.2 0.4)
< DC
< 10
0.3(0.2 0.4)
VP15TF
200(150 300)
< DC
< 10
0.3(0.2 0.4)
< DC
< 10
0.3(0.2 0.4)
MC5020
200(150 250)
< 0.8DC
< 10
0.3(0.2 0.4)
< 0.6DC
< 10
0.3(0.2 0.4)
VP15TF
170(150 200)
< 0.8DC
< 10
0.3(0.2 0.4)
< 0.6DC
< 10
0.3(0.2 0.4)
MC5020
170(150 200)
< 0.8DC
< 10
0.2(0.1 0.3)
< 0.6DC
< 10
0.2(0.1 0.3)
VP15TF
150(100 200)
< 0.8DC
< 10
0.2(0.1 0.3)
< 0.6DC
< 10
0.2(0.1 0.3)
Speed
(m/min)
& 100
& 125
ap (mm)
fz (mm/t.)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
< 10
0.3(0.2 0.4)
< DC
< 10
0.3(0.2 0.4)
< 10
0.3(0.2 0.4)
< DC
< 10
0.3(0.2 0.4)
< 0.5DC
< 10
0.3(0.2 0.4)
< 0.4DC
< 10
0.3(0.2 0.4)
170(150 200)
< 0.5DC
< 10
0.3(0.2 0.4)
< 0.4DC
< 10
0.3(0.2 0.4)
MC5020
170(150 200)
< 0.5DC
< 10
0.2(0.1 0.3)
< 0.4DC
< 10
0.2(0.1 0.3)
VP15TF
150(100 200)
< 0.5DC
< 10
0.2(0.1 0.3)
< 0.4DC
< 10
0.2(0.1 0.3)
MC5020
300(250 350)
VP15TF
250(200 300)
MC5020
220(150 300)
VP15TF
200(150 300)
MC5020
200(150 250)
VP15TF
Speed
(m/min)
ap (mm)
fz (mm/t.)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
< DC
< DC
ae (mm)
& 160
& 200 &250
ae (mm)
ap (mm)
fz (mm/t.)
ae (mm)
ap (mm)
fz (mm/t.)
MC5020
300(250 350)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
VP15TF
250(200 300)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
MC5020
220(150 300)
< DC
< 10
0.3(0.2 0.4)
< DC
< 10
0.3(0.2 0.4)
VP15TF
200(150 300)
< DC
< 10
0.3(0.2 0.4)
< DC
< 10
0.3(0.2 0.4)
MC5020
200(150 250)
< 0.3DC
< 10
0.3(0.2 0.4)
< 0.2DC
< 10
0.3(0.2 0.4)
VP15TF
170(150 200)
< 0.3DC
< 10
0.3(0.2 0.4)
< 0.2DC
< 10
0.3(0.2 0.4)
MC5020
170(150 200)
< 0.3DC
< 10
0.2(0.1 0.3)
< 0.2DC
< 10
0.2(0.1 0.3)
VP15TF
150(100 200)
< 10
0.2(0.1 0.3)
< 0.2DC
< 10
0.2(0.1 0.3)
< 0.3DC
(Note 1) DC is cutter diameter.

(Note 2) When using wiper insert, please reduce the feed per tooth to half the normal rate.
L038
ae (mm)
y VOX400 (Extra fine pitch)
Tensile
Strength
< 200MPa
Gray Cast Iron

< 350MPa
< 450MPa
Ductile Cast Iron

< 800MPa
Work Material
Tensile
Strength
< 200MPa
Gray Cast Iron

< 350MPa
< 450MPa
Ductile Cast Iron

< 800MPa
Work Material
Tensile
Strength
< 200MPa
Gray Cast Iron

< 350MPa
< 450MPa
Ductile Cast Iron

< 800MPa
Speed
(m/min)
& 63
& 80
ae (mm)
ap (mm)
fz (mm/t.)
ae (mm)
ap (mm)
fz (mm/t.)
MC5020
300(250 350)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.3(0.2 0.4)
VP15TF
250(200 300)
MC5020
220(150 300)
< DC
< 10
0.3(0.2 0.4)
VP15TF
200(150 300)
< DC
< 10
0.3(0.2 0.4)
< DC
< 10
0.3(0.2 0.4)
MC5020
200(150 250)
< 0.6DC
< 10
0.3(0.2 0.4)
< 0.5DC
< 10
0.3(0.2 0.4)
VP15TF
170(150 200)
< 0.6DC
< 10
0.3(0.2 0.4)
< 0.5DC
< 10
0.3(0.2 0.4)
MC5020
170(150 200)
< 0.6DC
< 10
0.2(0.1 0.3)
< 0.5DC
< 10
0.2(0.1 0.3)
VP15TF
150(100 200)
< 0.6DC
< 10
0.2(0.1 0.3)
< 0.5DC
< 10
0.2(0.1 0.3)
Speed
(m/min)
& 100
& 125
ae (mm)
ap (mm)
fz (mm/t.)
ae (mm)
ap (mm)
fz (mm/t.)
MC5020
300(250 350)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
VP15TF
250(200 300)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
MC5020
220(150 300)
< DC
< 10
0.3(0.2 0.4)
< DC
< 10
0.3(0.2 0.4)
VP15TF
200(150 300)
< DC
< 10
0.3(0.2 0.4)
< DC
< 10
0.3(0.2 0.4)
MC5020
200(150 250)
< 0.4DC
< 10
0.3(0.2 0.4)
< 0.3DC
< 10
0.3(0.2 0.4)
VP15TF
170(150 200)
< 0.4DC
< 10
0.3(0.2 0.4)
< 0.3DC
< 10
0.3(0.2 0.4)
MC5020
170(150 200)
< 0.4DC
< 10
0.2(0.1 0.3)
< 0.3DC
< 10
0.2(0.1 0.3)
VP15TF
150(100 200)
< 10
0.2(0.1 0.3)
< 0.3DC
< 10
0.2(0.1 0.3)
Speed
(m/min)
< 0.4DC
& 160
& 200 &250
ae (mm)
ap (mm)
fz (mm/t.)
ae (mm)
ap (mm)
fz (mm/t.)
MC5020
300(250 350)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
VP15TF
250(200 300)
< DC
< 10
0.4(0.3 0.5)
< DC
< 10
0.4(0.3 0.5)
MC5020
220(150 300)
< DC
< 10
0.3(0.2 0.4)
< DC
< 10
0.3(0.2 0.4)
VP15TF
200(150 300)
< DC
< 10
0.3(0.2 0.4)
< DC
< 10
0.3(0.2 0.4)
MC5020
200(150 250)
< 0.25DC
< 10
0.3(0.2 0.4)
< 0.15DC
< 10
0.3(0.2 0.4)
< 0.25DC
< 10
0.3(0.2 0.4)
< 0.15DC
< 10
0.3(0.2 0.4)
< 0.15DC
< 10
0.2(0.1 0.3)
< 0.15DC
< 10
0.2(0.1 0.3)
VP15TF
170(150 200)
MC5020
170(150 200)
< 0.25DC
< 10
0.2(0.1 0.3)
VP15TF
150(100 200)
< 0.25DC
< 10
0.2(0.1 0.3)
MILLING
Work Material
(Note 1) DC is cutter diameter.

(Note 2) When using wiper insert, please reduce the feed per tooth to half the normal rate.
y Usable cutting edge width of wiper inserts

The width of the wiper insert itself is 5.5mm, however the
actual functioning cutting edge width after installation to the
body is 4.5mm, as shown in the diagram.
With one wiper insert, it is possible to machine up to fr=4mm
feed per revolution. When exceeding fr=4mm, use two or
more wiper inserts. Note that there is a possibility to exceed
fr=4mm when using a holder with more than 24 inserts.
4.5mm
L039
INDEXABLE MILLING
DAH
DCCB
DC
inserts.
RE
Fig.3
200
250
Number
of Teeth
Type
Coarse Pitch
Fine Pitch
MILLING
Stock
18
DCCB
DC
KAPR :0
GAMP :+11
T :-9 -11
GAMF :-9-11 I :+11
Order Number
BD
101.6
DCON
KWW
RE
L8
edge inserts.
a Curved cutting edge
and high rigidity holder.
a Screw-on type.
y ARBOR TYPE
L8
DCCB
DC
RE

Dimensions(mm)
DC
LF
DCON
CBDP DAH
BD
KWW
L8
DCCB
WT
(kg)
APMX
(mm)
Type
(Fig.)
ASX400-050A03R
50
40
22
20
11
41
10.4
6.3
17
0.3
10
ASX400-063A04R
63
40
22
20
11
50
10.4
6.3
17
0.5
10
ASX400R08004C
80
50
25.4
26
60
9.5
38
1.0
10
ASX400R10005D
100
50
31.75
32
70
12.7
45
1.5
10
ASX400R12506E
125
63
38.1
35
80
15.9
10
60
2.5
10
ASX400R16008F
160
63
50.8
38
100
19.1
11
90
4.0
10
ASX400R20010K
10
200
63
47.625
35
160
25.4
14.22
135
7.0
10
ASX400R25012K
12
250
63
47.625
35
210
25.4
14.22
180
12.0
10
ASX400-050A04R
50
40
22
20
11
41
10.4
6.3
17
0.3
10
ASX400-063A05R
63
40
22
20
11
50
10.4
6.3
17
0.5
10
ASX400R08006C
80
50
25.4
26
60
9.5
38
1.0
10
ASX400R10007D
100
50
31.75
32
70
12.7
45
1.5
10
ASX400R12508E
125
63
38.1
35
80
15.9
10
60
2.5
10
ASX400R16012F
12
160
63
50.8
38
100
19.1
11
90
4.0
10
ASX400R20016K
16
200
63
47.625
35
160
25.4
14.22
135
7.0
10
ASX400R25018K
18
250
63
47.625
35
210
25.4
14.22
180
12.0
10
WT : Tool Weight
SPARE PARTS
Tool Holder Number
ASX400
Shim
Shim Screw
Clamp Screw
Wrench (Insert)
Wrench (Shim)
STASX400N
WCS503507H
TPS35
TIP15T
HKY35R
L040
LF
CBDP
APMX
BD
DCON
KWW
80
100
125
160
CBDP
LF
K
Cast Iron
Fig.2
BD
DCON
KWW
APMX
M
Stainless Steel
Fig.1
50
63
Roughing
CBDP
LF
P
Steel
Finishing
L8
<GENERAL CUTTING>
APMX
SHOULDER MILLING
ASX400
L8
DCCB
DC
RE
RE
DC
LF
50
40
22
63
40
ASX400-080B04R
80
ASX400-100B05R
ASX400-125B06R
ASX400-160C08R
Dimensions(mm)
DAH
BD
KWW
L8
DCCB
WT
(kg)
20
11
41
10.4
6.3
17
22
20
11
50
10.4
6.3
50
27
29
60
12.4
100
50
32
32
70
125
63
40
32
160
63
40
29
ASX400-200C10R
10
200
63
60
ASX400-250C12R
12
250
63
60
ASX400-050A04R
50
40
ASX400-063A05R
63
40
ASX400-080B06R
80
ASX400-100B07R
ASX400-125B08R
ASX400-160C12R
APMX
(mm)
Type
(Fig.)
0.3
10
17
0.5
10
38
0.9
10
14.4
45
1.4
10
80
16.4
60
2.3
10
100
16.4
56
3.6
10
32
160
25.7
14.22
135
6.3
10
32
210
25.7
14.22
180
10.8
10
22
20
11
41
10.4
6.3
17
0.3
10
22
20
11
50
10.4
6.3
17
0.5
10
50
27
29
60
12.4
38
0.9
10
100
50
32
32
70
14.4
45
1.4
10
125
63
40
32
80
16.4
60
2.2
10
12
160
63
40
29
100
16.4
56
3.5
10
ASX400-200C16R
16
200
63
60
32
160
25.7
14.22
135
6.2
10
ASX400-250C18R
18
250
63
60
32
210
25.7
14.22
180
10.7
10
ASX400-050A05R
50
40
22
20
11
41
10.4
6.3
17
0.3
10
ASX400-063A06R
63
40
22
20
11
50
10.4
6.3
17
0.5
10
ASX400-080B08R
80
50
27
29
60
12.4
38
0.9
10
ASX400-100B10R
10
100
50
32
32
70
14.4
45
1.4
10
ASX400-125B12R
12
125
63
40
32
80
16.4
60
2.1
10
ASX400-160C15R
15
160
63
40
29
100
16.4
56
3.4
10
ASX400-200C19R
19
200
63
60
32
160
25.7
14.22
135
6.2
10
ASX400-250C22R
22
250
63
60
32
210
25.7
14.22
180
10.5
10
Order Number
ASX400-050A03R
ASX400-063A04R
DCON CBDP
MILLING
Number
of Teeth
Type
Coarse Pitch
Fine Pitch
Extra Fine Pitch
DCCB
DC
KAPR :0
GAMP :+11
T :-9 -11
GAMF :-9 -11 I :+11
18
CBDP
LF
APMX
Stock
BD
101.6
DCON
KWW
RE
L8
200
250
14
For metric arbor
y ARBOR TYPE
LF
Fig.4
BD
66.7
DCON
KWW
L8
160
DCCB
DC
RE
CBDP
LF
Fig.3
APMX CBDP
L8
APMX CBDP
DAH
DCCB
DC
BD
DCON
KWW
80
100
125
LF
Fig.2
BD
DCON
KWW
APMX
Fig.1
50
63
* WT : Tool Weight
SPARE PARTS
TECHNICAL DATA
P001
Q001
L041
DC
DCON
INDEXABLE MILLING
APMX
RE
LH
LF
Type
y SHANK TYPE

Stock
Order Number
Dimensions(mm)
Number
of Teeth
LF
DCON
LH
APMX
Coarse Pitch
DC
ASX400R403S32
40
125
32
40
10
ASX400R503S32
50
125
32
40
10
ASX400R634S32
63
125
32
40
10
ASX400R804S32
80
125
32
40
10
Fine Pitch
ASX400R504S32
50
125
32
40
10
ASX400R635S32
63
125
32
40
10
ASX400R806S32
80
125
32
40
10
SPARE PARTS
Tool Holder Number
ASX400
Shim
Shim Screw
Clamp Screw
Wrench (Insert)
Wrench (Shim)
STASX400N
WCS503507H
TPS35
TIP15T
HKY35R

A
BD
MILLING
DC
DCON
CRKS
A
RE
APMX
LF
L11
A-A section
OAL
Number of Teeth

Coolant Hole
Order Number
Stock
y SCREW-IN TYPE
Dimensions (mm)
DC DCON BD OAL LF L11
WT
*2
H CRKS APMX (kg)
Shim
Shim
Screw
Clamp
Screw
Wrench
(Insert)
Wrench
(Shim)
ASX400R322AM1640
a u
2 32 17 29 63 40
24 M16 10 0.3
WCS503507H
TPS35
TIP15T
HKY35R
ASX400R403AM1645
a u
3 40 17 29 68 45
24 M16 10 0.3 STASX400N WCS503507H
TPS35
TIP15T
HKY35R
(Note) For screw-in type arbors, refer to page L145 L146.

1 WT : Tool Weight
2 Clamp Torque (N m) : WCS503507H=5.0, TPS35=3.5
*
*
L042

Steel

: Stable Cutting
: General Cutting
: Unstable Cutting
Stainless Steel
Cast Iron
Non-ferrous Metal
Honing :

Hardened Steel
Coated
JL Breaker
SOET12T308PEER-JL
E E
IC
Geometry
BS RE
RE
12.7 3.97 1.4 0.8
a a a a a a a a a
BS
Order Number
HTi10
Shape
Class
Honing
F7030
MC5020
N
MP6120 EW
N
MP6130 EW
N
MP7130 EW
N
MP7140 EW
N
MP9120 EW
N
MP9130 EW
VP15TF
VP30RT
NX4545
IC
12.7 3.97 1.4 0.8
RE
BS
JM Breaker SOMT12T308PEER-JM M E
IC
SOMT12T308PEER-JH M E
RE
12.7 3.97 1.4 0.8
a a a a a a a a a a
BS
JH Breaker
IC
SOMT12T320PEER-FT M E
a a
12.7 3.97 0.5 2.0
a a a
RE
BS
FT Breaker
IC
JP Breaker
SOGT12T308PEFR-JP G F
RE
12.7 3.97 1.4 0.8
BS
For Aluminium Alloy Heavy Interrupted Cutting MediumHeavy Cutting LightRough Cutting FinishLight Cutting Application
Work
Material
P
M
K
N
S
H
IC
MILLING
WIPER INSERTS
WOEW12T308PETR8C E T
a
a
W1
Geometry
BS RE
12.5 13.2 3.97
0.8
12.5 13.2 3.97
0.8
R500
WOEW12T308PEER8C E E
Dimensions(mm)
W1
Order Number
HTi05T
Shape
Class
Honing
NX2525
Cermet Carbide
BS
L
SCREW-IN ARBORS
SPARE PARTS
TECHNICAL DATA
RE
S
L145
P001
Q001
L043
INDEXABLE MILLING
Work Material
Hardness
Mild Steel
< 180HB
180 280HB
Carbon Steel
Alloy Steel
280 350HB
M
Stainless Steel
N
S
MILLING
< 270HB
Cast Iron
Ductile Cast Iron
Tensile Strength
< 450MPa
Aluminium Alloy
Titanium Alloy

(Inconel etc.)
Hardened Steel
40 55HRC
aRevolution (min
Grade
Cutting Speed
(SFM)
Finish Light Cutting LightRough Cutting Medium Heavy Cutting

Feed per Tooth (mm/t.) Breaker Feed per Tooth (mm/t.) Breaker Feed per Tooth (mm/t.) Breaker
F7030
280 (210 350)
0.18 (0.08 0.28)
JL
0.20 (0.10 0.30)
JM
0.25 (0.10 0.35)
JH
MP6120
VP15TF
250 (200 300)
0.18 (0.08 0.28)
JL
0.20 (0.10 0.30)
JM
0.25 (0.10 0.35)
JH
FT
MP6130
240 (190 290)
0.18 (0.08 0.28)
JL
0.20 (0.10 0.30)
JM
0.25 (0.10 0.35)
JH
VP30RT
230 (180 280)
0.18 (0.08 0.28)
JL
0.20 (0.10 0.30)
JM
0.25 (0.10 0.35)
JH
NX4545
180 (130 230)
0.15 (0.07 0.23)
JL
0.18 (0.10 0.28)
JM
F7030
250 (200 300)
0.15 (0.07 0.23)
JL
0.18 (0.10 0.28)
JM
0.20 (0.10 0.30)
JH
MP6120
VP15TF
220 (170 270)
0.15 (0.07 0.23)
JL
0.18 (0.10 0.28)
JM
0.20 (0.10 0.30)
JH
FT
MP6130
180 (150 230)
0.15 (0.07 0.23)
JL
0.18 (0.10 0.28)
JM
0.20 (0.10 0.30)
JH
VP30RT
150 (120 180)
0.15 (0.07 0.23)
JL
0.18 (0.10 0.28)
JM
0.20 (0.10 0.30)
JH
NX4545
150 (120 180)
0.13 (0.06 0.20)
JL
0.15 (0.10 0.25)
JM
F7030
180 (130 230)
0.13 (0.06 0.20)
JL
0.15 (0.10 0.25)
JM
0.18 (0.10 0.28)
JH
MP6120
VP15TF
140 (100 180)
0.13 (0.06 0.20)
JL
0.15 (0.10 0.25)
JM
0.18 (0.10 0.28)
JH
FT
MP6130
120 (90 150)
0.13 (0.06 0.20)
JL
0.15 (0.10 0.25)
JM
0.18 (0.10 0.28)
JH
VP30RT
100 (80 160)
0.13 (0.06 0.20)
JL
0.15 (0.10 0.25)
JM
0.18 (0.10 0.28)
JH
NX4545
100 (80 160)
0.10 (0.05 0.15)
JL
0.13 (0.10 0.20)
JM
MP7130
VP15TF
MP7140
VP30RT
220 (170 270)
0.15 (0.07 0.23)
JL
0.18 (0.10 0.28)
JM
0.20 (0.10 0.30)
JH
FT
200 (150 250)
0.15 (0.07 0.23)
JL
0.18 (0.10 0.28)
JM
0.20 (0.10 0.30)
JH
NX4545
150 (120 180)
0.15 (0.07 0.23)
JL
0.18 (0.10 0.28)
JM
JH
FT
JH
FT
MC5020
200 (150 250)
0.20 (0.10 0.30)
JM
0.25 (0.10 0.35)
VP15TF
180 (130 230)
0.18 (0.10 0.28)
JL
0.20 (0.10 0.30)
JM
0.25 (0.10 0.35)
HTi10
650 (300 1000)
0.15 (0.10 0.20)
JP
0.20 (0.10 0.30)
JP
0.30 (0.20 0.40)
JP
JH
FT
JH
FT
JH
FT
JH
FT
JH
FT
MP9120
VP15TF
50 (40 60)
0.12 (0.05 0.20)
JL
0.15 (0.05 0.20)
JM
0.18 (0.10 0.28)
MP9130
45 (30 55)
0.10 (0.05 0.20)
JL
0.15 (0.05 0.20)
JM
0.18 (0.10 0.28)
MP9120
VP15TF
40 (20 50)
0.12 (0.05 0.20)
JL
0.15 (0.05 0.20)
JM
0.18 (0.10 0.28)
MP9130
35 (15 45)
0.10 (0.05 0.20)
JL
0.15 (0.05 0.20)
JM
0.18 (0.10 0.28)
VP15TF
80 (60 100)
0.08 (0.04 0.13)
JL
0.10 (0.05 0.15)
JM
0.12 (0.07 0.17)
=(1000 x Cutting Speed)u(3.14 x DC) aTable Feed (mm/min)=Feed per Tooth x Number of Teeth x Cutter Revolution
-1)
INSTRUCTIONS FOR USING INSERTS

y Instructions for use of the JP breaker
a The JP breaker has sharp cutting edges.
Wear gloves when handling.

a When machining aluminium alloy, welding to
the cutting edge tends to occur, often leading

to insert failure. To prevent this, wet cutting is
recommended.

a Wiper inserts for the ASX400 are
single-cornered.
a When installing the wiper insert, place the
insert so that the small chamfer is located

as shown.
a The peripheral cutting edge of the wiper
insert is located back than general inserts.

Beware of wear of the insert just behind the
wiper insert.
a When using wiper set the following standard
conditions. Depth of Cut (ap) < 0.5mm, Feed

per Tooth (fz) < 0.2mm/t.
L044
FEATURES
y ECONOMICAL
y LOW RESISTANCE
y HIGH ACCURACY
ASX400 is economical as it employs
Due to the 3D design of the cutting edge and a

large rake angle, high cutting edge sharpness has
been achieved with reduced cutting resistance.
Due to the curved edge and high accuracy

body and insert, high accuracy surface
finish on walls and high quality surface
finish on faces can be achieved.
inserts that have 4 cutting edges. Additionally

with one tool, it is possible to carry out face
milling, shoulder milling, and slotting operations.
* JM breaker data
7mm pitch x 3
Tool
ASX400
30
Competitor A
100
Competitor B
122
Values obtained under

recommended cutting conditions.
Wall accuracy (!m)
Cutting edge diameter
y EASY TO USE
y HIGH RELIABILITY
y HIGH HEAT-RESISTANT BODY
Employs a screw on type mechanism,

therefore, the inserts can be easily set.
Additionally when indexing the insert, it is not
necessary to remove the screw completely.
Uses a carbide shim and Mitsubishi's proprietary

Anti-Fly-Insert (A.F.I) to prevent the inserts from
moving when machining. Additionally the clamp
screw uses TORXPLUS, for high clamping
force ensuring high reliability.
The cutter body is made from a special alloy that

provides high strength at high temperatures. A
special surface treatment improves the corrosion
and friction resistance. The ASX400 can be
used for long hours even under harsh conditions.
re
eratu
p
f tem
proo
Heat
ASX400
Conv
ention
al
1.7
tim
es
y CHIPBREAKERS FOR A WIDE RANGE OF APPLICATIONS
JM
Light to
Rough cutting
Breaker
a High accuracy insert
a High accuracy M class
with ground-finished
periphery.
a Large rake angle
leading to low cutting
resistance.
insert.
a For a wide range of
workpiece materials
and cutting conditions.
JH
Medium to
Heavy cutting
Breaker
FT
Heavy cutting/Heavy
interrupted cutting
Breaker
JP
Aluminium alloy
cutting
Breaker
a High accuracy M class
a High accuracy M-class a High accuracy insert

insert.
insert.
with ground-finished
periphery.
a Strong cutting edge for a Nose radius of 2.0mm
high fracture resistance.
has improved fracture
a Large rake angle and
resistance. Strong main
mirror-finished rake
cutting edge allows
face lead to sharp
heavy cutting and heavy
cutting performance
interrupted cutting. Stable
and high welding
cutting performance.
resistance.
MILLING
JL
Finish to Light
cutting
Breaker
y INSERT GRADES FOR A WIDE RANGE OF MATERIALS
Low
Cutting
Speed
High
Carbon Steel
Alloy Steel
F7030
MP6120
VP15TF
MP6130
VP30RT
Cutting Unstable
Stable Conditions
Stainless Steel
F7030
MP7130
VP15TF
MP7140
VP30RT
Cutting Unstable
Stable Conditions
Cast Iron
Ductile Cast Iron
MC5020
Aluminium Alloy
HTi10
Heat Treated Steel
MP9120
VP15TF
VP15TF
MP9130
VP15TF
Cutting Unstable
Stable Conditions

Titanium Alloy
Cutting Unstable
Stable Conditions
Cutting Unstable
Stable Conditions
Cutting Unstable
Stable Conditions
(Note) When machining steel or stainless steel and the emphasis is on surface finish, use cermet grade NX4545.
Stable Cutting : Continuous cutting, Constant depth of cut, Pre-machined securely clamped component cutting
Unstable Cutting : Heavy interrupted, Irregular depth of cut, Low clamping rigidity cutting
L045
INDEXABLE MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
Roughing
APX3000
M
Stainless Steel
Cast Iron
DC
10 (Max. Depth of Cut)
LH
LF
Fig.2
DC
Steel
DCON
Fig.1
DCON
Finishing

LH

LH
LF
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
DC
DCON
LF
LH
1
1
2
2
2
3
3
2
3
4
4
4
3
4
5
3
5
6
7
8
2
2
2
2
3
2
3
2
3
2
3
2
2
2
2
3
2
3
2
3
2
3
12
14
16
18
20
20
22
25
25
25
28
30
32
32
32
40
40
40
50
63
18
20
22
25
25
28
28
32
32
35
35
18
20
22
25
25
28
28
32
32
35
35
16
16
16
16
20
20
20
25
25
25
25
32
32
32
32
32
32
32
32
32
16
20
20
25
25
25
25
32
32
32
32
16
20
20
25
25
25
25
32
32
32
32
85
85
85
85
100
100
115
115
115
115
115
125
125
125
125
125
125
125
125
125
120
150
150
170
170
170
170
190
190
190
190
180
200
200
220
220
220
220
260
260
260
260
25
25
25
25
30
30
30
35
35
35
35
45
45
45
45
45
45
45
45
45
25
60
30
70
70
35
35
90
90
45
45
25
70
30
80
80
35
35
100
100
45
45
Dimensions(mm)
RMPX Revolution
(min-1)
Type(Fig.)
Number of Teeth
Extra Long
Long
MILLING
Standard
APX3000R121SA16SA
APX3000R141SA16SA
APX3000R162SA16SA
APX3000R182SA16SA
APX3000R202SA20SA
APX3000R203SA20SA
APX3000R223SA20SA
APX3000R252SA25SA
APX3000R253SA25SA
APX3000R254SA25SA
APX3000R284SA25SA
APX3000R304SA32SA
APX3000R323SA32SA
APX3000R324SA32SA
APX3000R325SA32SA
APX3000R403SA32SA
APX3000R405SA32SA
APX3000R406SA32SA
APX3000R507SA32SA
APX3000R638SA32SA
APX3000R182SA16LA
APX3000R202SA20LA
APX3000R222SA20LA
APX3000R252SA25LA
APX3000R253SA25LA
APX3000R282SA25LA
APX3000R283SA25LA
APX3000R322SA32LA
APX3000R323SA32LA
APX3000R352SA32LA
APX3000R353SA32LA
APX3000R182SA16ELA
APX3000R202SA20ELA
APX3000R222SA20ELA
APX3000R252SA25ELA
APX3000R253SA25ELA
APX3000R282SA25ELA
APX3000R283SA25ELA
APX3000R322SA32ELA
APX3000R323SA32ELA
APX3000R352SA32ELA
APX3000R353SA32ELA
coolant holes.
Stock
Type
Order Number
DC
DCON
y SHANK TYPE
LF
Fig.3
6.0
6.0
11.3
8.6
6.9
6.9
5.7
4.6
4.6
4.6
3.8
3.4
3.1
3.1
3.1
2.2
2.2
2.2
1.7
1.3
8.6
6.9
5.7
4.6
4.6
3.8
3.8
3.1
3.1
2.7
2.7
8.6
6.9
5.7
4.6
4.6
3.8
3.8
3.1
3.1
2.7
2.7
1
1
2
3
2
2
3
2
2
2
3
2
2
2
2
3
3
3
3
3
3
2
3
2
2
3
3
2
2
3
3
3
2
3
2
2
3
3
2
2
3
3
Max.
2 Allowable
10500
9000
20900
19600
18500
18500
17600
16400
16400
16400
15500
14900
14400
14400
14400
12800
12800
12800
11300
10000
19600
18500
17600
16400
16400
15500
15500
14400
14400
13700
13700
19600
18500
17600
16400
16400
15500
15500
14400
14400
13700
13700
*1
Clamp
Screw
TPS25
TPS25
TPS25
TPS25
TPS25
TPS25
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25
TPS25
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25
TPS25
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
TPS25 1
Wrench Anti-seize
Lubricant
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
(Note 1) When using inserts with corner radius RE> 2.4, machining of the holder is required as shown page L049.
(Note 2) The maximum allowable revolutions are set to ensure tool and insert stability.
(Note 3) When using the tool at high spindle speeds, ensure that the tool and arbor are correctly balanced.
1 Clamp Torque (N m) : TPS25=1.0, TPS25 1=1.0
2 RMPX : Max. Ramping Angle
L046
Inserts
AOMT
1236pp
PEER-p
AOGT
1236pp
PEFR-GM
BD
CBDP
L8
KWW
LF
10
(Max. Depth of Cut)
DCON
DAH
DCCB
DC
Cutter Diameter
DC
Set Bolt
& 32, & 40

& 50, & 63
& 80
&100
HSC08030H
10030H
12035H
16040H
a
a
a
16
16
22
22
25.4
31.75
18
18
20
20
26
32
9
9
11
11
13
17
30 8.4 5.6 14 0.2

34 8.4 5.6 14 0.3
45 10.4 6.3 17 0.4
55 10.4 6.3 17 0.7
70 9.5 6
20 1.3
80 12.7 8
26 2.2
L8
RMPX 2
WT 3
40
40
40
40
50
63
DCCB
5 32
6 40
7 50
8 63
9 80
11 100
KWW
BD
DAH
CBDP
DCON
APX3000-032A05RA
APX3000-040A06RA
APX3000-050A07RA
APX3000-063A08RA
APX3000R08009CA
APX3000R10011DA
LF
Dimensions(mm)
DC
Stock
Order Number
Number of Teeth
y ARBOR TYPE
KAPR :0
GAMP :+7 +21 T :+15 +27
GAMF :+15 +27 I :+7 +21
*1
Max.
Allowable
Revolution
(min-1)
Clamp
Screw
(kg)
3.1
2.2
1.7
1.3
1.0
0.8
14400
12800
11300
10000
8800
7800
Geometry
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
Wrench Anti-seize
Lubricant
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
Inserts
AOMT
1236pp
PEER-p
AOGT
1236pp
PEFR-GM
1 Clamp Torque (N m) : TPS25 1=1.0
3 WT : Tool Weight
*
*
*
10
(Max. Depth of Cut)
CBDP
L8
KWW
LF
BD
DCON
DCCB
DC
For metric arbor
& 32, & 40

& 50, & 63
& 80
&100
HSC08030H
10030H
12035H
16040H
RMPX 2
WT 3
DCCB
L8
KWW
BD
DAH
CBDP
DCON
APX3000-032A05RA
APX3000-040A06RA
APX3000-050A07RA
APX3000-063A08RA
APX3000-080A09RA
APX3000-100A11RA
LF
Dimensions(mm)
DC
Stock
Order Number
Set Bolt
KAPR :0
GAMP :+7 +21 T :+15 +27
GAMF :+15 +27 I :+7 +21
Number of Teeth
y ARBOR TYPE
Cutter Diameter
DC
(kg)
5 32
6 40
7 50
8 63
9 80
11 100
40
40
40
40
50
63
16
16
22
22
27
32
18
18
20
20
23
26
9
9
11
11
13
17
30
34
45
55
70
80
8.4
8.4
10.4
10.4
12.4
14.4
5.6
5.6
6.3
6.3
7
8
14
14
17
17
20
26
0.2
0.3
0.4
0.7
1.3
2.2
Max.
Allowable
Revolution
(min-1)
*1
Clamp
Screw
3.1
2.2
1.7
1.3
1.0
0.8
14400
12800
11300
10000
8800
7800
TPS251
TPS251
TPS251
TPS251
TPS251
TPS251
Wrench Anti-seize
Lubricant
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
TIP07F MK1KS
1 Clamp Torque (N m) : TPS25 1=1.0
3 WT : Tool Weight
*
*
Geometry
MILLING
DAH
Inserts
AOMT
1236pp
PEER-p
AOGT
1236pp
PEFR-GM
SPARE PARTS
TECHNICAL DATA
P001
Q001
L047
INDEXABLE MILLING
CRKS
BD
DC
DCON
10(Max. Depth of Cut)

LF
L11
OAL
A-A section
coolant holes.
y SCREW-IN TYPE
DC DCON BD
APX3000R162M08A30
16
8.5
APX3000R182M08A30
18
8.5
APX3000R203M10A30
20
APX3000R223M10A30
APX3000R254M12A35
APX3000R284M12A35
APX3000R304M16A40
Order Number
Stock
R
Number of Teeth
*2
Dimensions(mm)
WT
(kg)
OAL
LF
L11
CRKS
13
48
30
10
M8
0.1 TPS25
Wrench Anti-seize
Lubricant
TIP07F MK1KS
13
48
30
10
M8
0.1 TPS25
TIP07F
MK1KS
10.5
18
49
30
14
M10 0.1 TPS25
TIP07F
MK1KS
22
10.5
18
49
30
14
M10 0.1 TPS251 TIP07F
MK1KS
25
12.5
21
57
35
19
M12 0.2 TPS251 TIP07F
MK1KS
28
12.5
21
57
35
19
M12 0.2 TPS251 TIP07F
MK1KS
30
17
29
63
40
24
M16 0.3 TPS251 TIP07F
MK1KS
APX3000R325M16A40
32
17
29
63
40
24
M16 0.3 TPS251 TIP07F
MK1KS
APX3000R355M16A40
35
17
29
63
40
24
M16 0.3 TPS251 TIP07F
MK1KS
APX3000R406M16A40
40
17
29
63
40
24
M16 0.3 TPS251 TIP07F
MK1KS
Clamp
Screw
(Note 2) For screw-in type arbors, refer to page L145 L146.
1 Clamp Torque (N m) : TPS25=1.0, TPS25 1=1.0
2 WT : Tool Weight
MILLING
*
*
L048
Inserts
AOMT
1236pp
PEER-p
AOGT
1236pp
PEFR-GM
INSERTS
Steel

: Stable Cutting
: General Cutting
Stainless Steel
: Unstable Cutting
Cast Iron
Non-ferrous Metal
Honing :
E : Round F : Sharp
Dimensions (mm)
Shape
Order Number
General
M Breaker
AOMT123602PEER-M
M E
a a a a a a a
12 6.6 3.6 1.8 0.2
AOMT123604PEER-M
M E
a a a a a a a
12 6.6 3.6 1.6 0.4
AOMT123608PEER-M
M E
a a a a a a a
12 6.6 3.6 1.2 0.8
AOMT123610PEER-M
M E
a a a a a a a
12 6.6 3.6 1.0 1.0
AOMT123612PEER-M
M E
a a a a a a a
12 6.6 3.6 0.8 1.2
AOMT123616PEER-M
M E
a a a a a a a
12 6.6 3.6 0.4 1.6
AOMT123620PEER-M
M E
a a a a a a a
12 6.6 3.6 0.4 2.0
AOMT123624PEER-M
M E
a a a a a a a
12 6.6 3.6 0.4 2.4
AOMT123630PEER-M
M E
a a a a a a a
12 6.6 3.6 0.4 3.0
AOMT123632PEER-M
M E
a a a a a a a
12 6.6 3.6 0.4 3.2
Strong Cutting Edge Type AOMT123604PEER-H

H Breaker
M E
a a a a a a a a
12 6.6 3.6 1.6 0.4
AOMT123608PEER-H
M E
a a a a a a a a
12 6.6 3.6 1.2 0.8
AOMT123616PEER-H
M E
a a a a a a a a
12 6.6 3.6 0.4 1.6
W1
Geometry
BS RE
L
11
W1
Carbide
Class
Honing
MC5020
N
MP6120 EW
N
MP6130 EW
N
MP7130 EW
N
MP9120 EW
N
MP9130 EW
VP15TF
VP20RT
TF15
Coated
RE
L
11
W1
Hardened Steel
BS
BS
Work
Material
P
M
K
N
S
H
RE
12 6.6 3.6 1.8 0.2
AOGT123604PEFR-GM G F
12 6.6 3.6 1.6 0.4
AOGT123608PEFR-GM G F
12 6.6 3.6 1.2 0.8
L
11
W1
BS
For Machining of Aluminium Alloys AOGT123602PEFR-GM G F

GM Breaker
RE
=
MILLING
Nose R is different from the workpiece of R shape depending on the axial rake angle of the body.
* Consult
us for more details.
NOTE ON USE OF INSERTS WITH LARGE CORNER RADII

When using inserts with corner radius RE> R2.4,
please machine the holder with a radius form as shown
on the right.
RE
SCREW-IN ARBORS
SPARE PARTS
TECHNICAL DATA
RE (mm)
R (mm)
2.4
3.0
3.2
1.9
2.5
2.7
R : Holder end radius

RE : Insert corner radius
L145
P001
Q001
L049
INDEXABLE MILLING
y CUTTING SPEED
Work Material
M
K
N
S
Hardness
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180350HB
Stainless Steel
Gray Cast Iron
Ductile, Cast Iron
Aluminium Alloy
< 270HB
< 350MPa
< 800MPa
Titanium Alloy
< 350HB
Hardened Steel
4055HRC
Insert
Grade
Breaker
1st Recommenedation 2nd Recommenedation
MP6120
MP6130
MP6120
MP6130
MP7130
MC5020
MC5020
TF15
MP9120
MP9130
MP9120
MP9130
VP15TF
VP15TF
VP20RT
VP15TF
VP20RT
VP20RT
VP15TF
VP15TF
VP15TF
VP20RT
VP15TF
VP20RT
M
M
M
M
M
H
H
GM
M
M
M
M
H
H
H
H
H
H
H
H
H
H
<0.25DC
Cutting Width ae (mm)

0.250.5DC
0.50.75DC
Cutting Speed vc (m/min)
DC (Slot)
230(180270) 220(170260)
180(140210)
180(140210)
200(150240) 190(140230)
150(110180)
150(110180)
180(140210)
170(130200)
140(110160)
140(110160)
150(110180)
140(100170)
110(80130)
110(80130)
180(140210)
170(130200)
140(110160)
140(110160)
250(200300) 240(190290) 210(160260)
140(110160)
130(100150)
120(90140)
100(80120)
100(80120)
500(2001000) 500(2001000) 500(2001000) 500(2001000)
50(4070)
50(4070)
40(3060)
40(3060)
40(3060)
40(3060)
30(2040)
30(2040)
90(70100)
85(60100)
70(5080)
70(5080)
y DEPTH OF CUT AND FEED

Work Material
Hardness
Cutting Width
ae (mm)
P
< 0.25DC
Mild Steel
Carbon Steel
Alloy Steel
< 180HB
0.250.5DC
DC (Slot)
M
< 0.25DC
< 270HB
0.250.5DC
MILLING
0.50.75DC
DC (Slot)
K
< 0.25DC
Gray Cast Iron
Tensile Strength
< 350MPa
0.250.5DC
0.50.75DC
DC (Slot)
< 0.25DC
Ductile, Cast Iron
Tensile Strength
< 800MPa
0.250.5DC
0.50.75DC
DC (Slot)
L050
28100
Depth of Cut Feed per Tooth Depth of Cut Feed per Tooth Depth of Cut Feed per Tooth
fz (mm/t.)
ap (mm)
fz (mm/t.)
ap (mm)
fz (mm/t.)
ap (mm)
<4
47
0.15
0.10
<2
25
0.15
0.10
<4
0.10
<3
0.10
<4
47
0.15
0.10
<2
25
0.15
0.10
<4
0.10
<3
0.10
<4
47
0.15
0.10
<2
25
0.15
0.10
<4
0.10
<3
0.10
<4
47
0.10
0.07
<2
25
0.10
0.07
<4
0.07
<3
0.07
180350HB
0.50.75DC
Stainless Steel
Cutter Diameter (mm)

1825
1216
<5
57
78.5
8.510
<3
35.5
5.58
810
<4
410
<4
47
<5
57
78.5
8.510
<3
35.5
5.58
810
<4
410
<4
47
<5
57
78.5
8.510
<3
35.5
5.58
810
<4
410
<4
47
<5
57
78.5
8.510
<3
35.5
5.58
810
<4
410
<4
47
0.25
0.20
0.15
0.10
0.25
0.20
0.15
0.10
0.15
0.10
0.10
0.07
0.20
0.15
0.10
0.07
0.20
0.15
0.10
0.07
0.10
0.07
0.10
0.07
0.25
0.20
0.15
0.10
0.25
0.20
0.15
0.10
0.15
0.10
0.10
0.07
0.20
0.15
0.10
0.07
0.20
0.15
0.10
0.07
0.10
0.07
0.10
0.07
<5
57
78.5
8.510
<3
35.5
5.58
810
<3
37
<3
35
<5
57
78.5
8.510
<3
35.5
5.58
810
<3
37
<3
35
<5
57
78.5
8.510
<3
35.5
5.58
810
<3
37
<3
35
<5
57
78.5
8.510
<3
35.5
5.58
810
<3
37
<3
35
0.20
0.15
0.10
0.07
0.20
0.15
0.10
0.07
0.10
0.07
0.10
0.07
0.20
0.15
0.10
0.07
0.20
0.15
0.10
0.07
0.10
0.07
0.10
0.07
0.20
0.15
0.10
0.07
0.20
0.15
0.10
0.07
0.10
0.07
0.10
0.07
0.20
0.15
0.10
0.07
0.20
0.15
0.10
0.07
0.10
0.07
0.10
0.07
Work Material
Cutting Width
ae (mm)
Hardness
0.250.5DC
0.50.75DC
DC (Slot)
S
Titanium Alloy
< 350HB
< 0.25DC
0.250.5DC
0.50.75DC
DC (Slot)
H
< 0.25DC
Hardened Steel
4055HRC
28100
fz (mm/t.)
ap (mm)
fz (mm/t.)
ap (mm)
fz (mm/t.)
ap (mm)
< 0.25DC
Aluminium Alloy

1825
1216
0.250.5DC
0.50.75DC
DC (Slot)
<4
47
<4
47
<5
<5
<4
47
<3
<2
<1
<4
47
0.15
0.10
0.15
0.10
0.10
0.10
0.15
0.10
0.05
0.10
0.05
0.10
0.07
<2
25
<4
<3
0.10
0.07
0.07
0.07
<4
47
<4
47
<5
<5
<4
47
<3
<2
<1
<5
57
78.5
<3
35.5
<4
<4
0.25
0.15
0.20
0.10
0.15
0.20
0.15
0.10
0.05
0.05
0.05
0.15
0.10
0.07
0.15
0.10
0.07
0.07
<4
47
<4
47
<5
<5
<4
47
<3
<2
<1
<5
57
0.20
0.10
0.20
0.10
0.10
0.15
0.10
0.07
0.05
0.05
0.05
0.15
0.10
<3
0.15
<3
0.07
0.07
<3
(Note 1) These cutting conditions are a guide to the standard shank type and the arbor type.
Please make adjustments according to the machining conditions.
(Note 2) Vibration is liable to occur in certain cases. Please reduce the depth of cut and / or reduce cutting conditions in the following cases.
When using the long shank type and extra long shank type.
When using long tool overhang with the standard or arbor type.
When the application has poor clamping rigidity or when using a low rigidity machine.
(Note 3) In case of coarse and fine pitch cutters, the coarse pitch type is recommended to prevent vibration.
(Note 4) For heavy interrupted and unstable cutting, the H breaker is first recommendation.
y RAMPING/HELICAL CUTTING
a RAMPING
a HELICAL CUTTING
L
Blind holes,
Flat bottom
Through holes
Pitch
(P)
Pitch
(P)
L=
APMX
tan %
RMPX
DC
Refer to the table below for cutting conditions. For feed per tooth and cutting speed,
follow the cutting conditions for slot milling.
DC
DC
Hole
diameter
(DH)
Hole
diameter
(DH)
Ramping
Helical Cutting (Blind Hole, Flat Bottom)
Cutting Edge
Minimum
Maximum
Maximum
Hole
Maximum
Minimum Hole
Maximum
Diameter
Distance 1
Ramping Angle
Diameter 2
Pitch
Diameter
Pitch
DC(mm)
RMPX
L(mm)
P max.(mm)
DH max.(mm) P max.(mm)
DH min.(mm)
12
14
16
18
20
22
25
28
30
32
35
40
50
63
80
100
6.0
6.0
11.3
8.6
6.9
5.7
4.6
3.8
3.4
3.1
2.7
2.2
1.7
1.3
1.0
0.8
95
95
50
66
83
100
124
151
168
185
212
260
337
441
573
716
22
26
30
34
38
42
48
54
58
62
68
78
98
124
158
198
2.5
2.5
9
5
5
5
6
4.5
4.5
4.5
4
4
2
2
2
1
20.5
24.5
28
32
36
40
46
52
56
60
66
76
96
122
156
196
2
2
7
4.5
4.5
4.5
5
4
4
4
3.5
3.5
2
2
2
1
Helical Cutting (Through Hole)

Minimum Hole
Diameter
DH min.(mm)
Maximum
Pitch
P max.(mm)
14
18
21
25
29
33
39
45
49
53
59
69
89
115
149
189
0.5
1
2
2
2
2
3
2
2
2
2
2
2
2
2
1
MILLING
APMX
(Note) When machining highly ductile materials with ramping angles above, chips could be continuous.
In this case, decrease the ramping angle or feed per tooth.
1 L (=10 / tan %). Cutters' moving distance until depth of cut reaches 10mm at a maximum ramping angle.
2 In case corner radius of 0.8mm. Other than that, find with the below formula.
{(cutting edge diameter DC) (corner radius) 0.2) }2
*
*
L051
INDEXABLE MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
Finishing
APX4000
K
Cast Iron
DCON
M
Stainless Steel
Fig.1
DC
P
Steel
Roughing
LH
LF
DC

LH

DC
DCON
LF
LH
25
25
115
35
11
18900
32
32
125
45
16300
32
32
125
45
APX4000R403SA32SA
40
32
125
45
APX4000R404SA32SA
40
32
125
APX4000R504SA32SA
50
32
APX4000R505SA32SA
50
APX4000R634SA32SA
APX4000R636SA32SA
APX4000R252SA25LA
APX4000R282SA25LA
APX4000R322SA32LA
Stock
Number of Teeth
Type
Standard
Long
Extra Long
MILLING
LF
coolant holes.
y SHANK TYPE
Order Number
DCON
Fig.2
Dimensions(mm)
Max.
2 Allowable Type
RMPX Revolution (Fig.)
(min-1)
Clamp
Screw
Wrench Anti-seize
Lubricant
TPS4
TIP15W MK1KS
TPS4
TIP15W MK1KS
16300
TPS4
TIP15W MK1KS
14200
TPS43
TIP15W MK1KS
45
14200
TPS43
TIP15W MK1KS
125
45
12400
TPS43
TIP15W MK1KS
32
125
45
12400
TPS43
TIP15W MK1KS
63
32
125
45
10800
TPS43
TIP15W MK1KS
63
32
125
45
10800
TPS43
TIP15W MK1KS
25
25
170
35
11
18900
TPS4
TIP15W MK1KS
28
25
170
35
17700
TPS4
TIP15W MK1KS
32
32
190
45
16300
TPS4
TIP15W MK1KS
APX4000R323SA32LA
32
32
190
45
16300
TPS4
TIP15W MK1KS
APX4000R352SA32LA
35
32
190
45
15400
TPS4
TIP15W MK1KS
APX4000R353SA32LA
35
32
190
45
15400
TPS4
TIP15W MK1KS
APX4000R402SA32LA
40
32
190
45
14200
TPS43
TIP15W MK1KS
APX4000R403SA32LA
40
32
190
45
14200
TPS43
TIP15W MK1KS
APX4000R404SA32LA
40
32
190
45
14200
TPS43
TIP15W MK1KS
APX4000R252SA25ELA
25
25
220
80
11
18900
TPS4
TIP15W MK1KS
APX4000R282SA25ELA
28
25
220
35
17700
TPS4
TIP15W MK1KS
APX4000R322SA32ELA
32
32
260
100
16300
TPS4
TIP15W MK1KS
APX4000R323SA32ELA
32
32
260
100
16300
TPS4
TIP15W MK1KS
APX4000R352SA32ELA
35
32
260
45
15400
TPS4
TIP15W MK1KS
APX4000R353SA32ELA
35
32
260
45
15400
TPS4
TIP15W MK1KS
APX4000R402SA32ELA
40
32
260
45
14200
TPS43
TIP15W MK1KS
APX4000R403SA32ELA
40
32
260
45
14200
TPS43
TIP15W MK1KS
APX4000R404SA32ELA
40
32
260
45
14200
TPS43
TIP15W MK1KS
APX4000R252SA25SA
APX4000R322SA32SA
APX4000R323SA32SA
1 Clamp Torque (N m) : TPS4=3.5, TPS43=3.5
*
*
L052
Inserts
AOMT
1848pp
PEER-p
a
a
a
a
5.6
6.3
6.3
6
8
10
11
14
17
17
20
26
56
72
(kg)
0.2
0.3
0.5
1.2
2.1
3.3
4.8
6 14200
4 12400
3 10800
2
9300
1.5 8100
1
7100
1
6100
1
1
1
1
1
2
2
*1
Clamp
Wrench Anti-seize
Screw
Lubricant
TPS43
TPS43
TPS43
TPS43
TPS43
TPS43
TPS43
TIP15W
TIP15W
TIP15W
TIP15W
TIP15W
TIP15W
TIP15W
MK1KS
MK1KS
MK1KS AOMT
MK1KS 1848pp
MK1KS PEER-p
MK1KS
MK1KS
(kg)
8.4
10.4
10.4
12.4
14.4
16.4
16.4
5.6
6.3
6.3
7
8
9
9
14
17
17
20
27
56
72
0.2
0.3
0.5
1.2
2.1
3.3
4.8
WT 3
*
BD
9 34
11 45
11 50
13 60
17 70
90
100
DC
18
20
20
23
26
40
40
DCCB
16
22
22
27
32
40
40
L8
4 40 40
5 50 40
6 63 40
7 80 50
8 100 50
9 125 63
10 160 63
KWW
DAH
CBDP
DCON
Number of Teeth
Stock
a
L8
HSC08030H
10030H
12035H
16040H
MBA20040H
20040H
Dimensions(mm)
LF
APX4000-040A04RA
APX4000-050A05RA
APX4000-063A06RA
APX4000-080A07RA
APX4000-100A08RA
APX4000-125A09RA
APX4000-160A10RA
CBDP
&40
&50, & 63
&80
&100
&125
&160
Max.
Allowable
Revolution
(min-1)
Type(Fig.)
Set Bolt
KAPR :0
GAMP :+15 +22 T :+21 +28
GAMF :+21 +28 I :+15 +22
LF
Cutter Diameter
DC
Order Number
DCON
KWW
For metric arbor
y ARBOR TYPE
DC
Geometry
z x
z
*1
Clamp
Wrench Anti-seize
Screw
Lubricant
Insert
6 14200 1 TPS43 TIP15W MK1KS

4 12400 1 TPS43 TIP15W MK1KS
3 10800 1 TPS43 TIP15W MK1KS AOMT
2
9300 1 TPS43 TIP15W MK1KS 1848pp
1.5 8100 1 TPS43 TIP15W MK1KS PEER-p
1
7100 2 TPS43 TIP15W MK1KS
1
6100 2 TPS43 TIP15W MK1KS
1 Clamp Torque (N m) : TPS43=3.5
SPARE PARTS
3 WT : Tool Weight
*
*
Insert
DCCB
RMPX 2
DAH
DCCB
DC
15
(Max. Depth of Cut)
CBDP
L8
DCON
KWW
LF
z x
BD
BD
Fig.1
Fig.2
3 WT : Tool Weight
*
*
*
15
(Max. Depth of Cut)
L8
WT 3
DCCB
*
9 34 8.4
11 45 10.4
11 50 10.4
13 70 9.5
17 80 12.7
100 15.9
100 19.1
L8
KWW
BD
DAH
DCON
CBDP
18
20
20
26
32
40
40
Max.
Allowable
Revolution
(min-1)
Geometry
MILLING
4 40 40 16
5 50 40 22
6 63 40 22
7 80 50 25.4
8 100 63 31.75
9 125 63 38.1
10 160 63 50.8
CBDP
HSC08030H
10030H
12035H
16040H
MBA20040H
24045H
Type(Fig.)
Set Bolt
&40
&50, & 63
&80
&100
&125
&160
LF
LF
Cutter Diameter
DC
DC
15
(Max. Depth of Cut)
LF
APX4000-040A04RA
APX4000-050A05RA
APX4000-063A06RA
APX4000R08007CA
APX4000R10008DA
APX4000R12509EA
APX4000R16010FA
Dimensions(mm)
DC
Stock
Order Number
DCCB
KAPR :0
GAMP :+15 +22 T :+21 +28
GAMF :+21 +28 I :+15 +22
Number of Teeth
y ARBOR TYPE
BD
DCON
KWW
Fig.2
RMPX 2
L8
CBDP
DAH
DCCB
DC
15
(Max. Depth of Cut)
BD
DCON
KWW
Fig.1
TECHNICAL DATA
P001
Q001
L053
INDEXABLE MILLING
BD
DC
DCON
CRKS

LF
L11
OAL
A-A section
coolant holes.
y SCREW-IN TYPE
DC DCON
APX4000R252M12A35
25
APX4000R282M12A35
28
APX4000R322M16A40
APX4000R323M16A40
APX4000R352M16A40
APX4000R353M16A40
35
17
28.5
63
40
APX4000R403M16A40
40
17
28.5
63
40
APX4000R404M16A40
40
17
28.5
63
40
Order Number
Stock
R
Number of Teeth
*2
Dimensions(mm)
WT
(kg)
Clamp
Screw
Wrench Anti-seize
Lubricant
BD
OAL
LF
L11
CRKS
12.5
23.5
57
35
19
M12
0.2 TPS4
TIP15W MK1KS
12.5
23.5
57
35
19
M12
0.2 TPS4
TIP15W MK1KS
32
17
28.5
63
40
24
M16
0.3 TPS4
TIP15W MK1KS
32
17
28.5
63
40
24
M16
0.3 TPS4
TIP15W MK1KS
35
17
28.5
63
40
24
M16
0.3 TPS4
TIP15W MK1KS
24
M16
0.3 TPS4
TIP15W MK1KS
24
M16
0.3 TPS43 TIP15W MK1KS
24
M16
0.3 TPS43 TIP15W MK1KS
2 WT : Tool Weight
MILLING
*
*
L054
Insert
AOMT
1848pp
PEER-p
INSERTS
Steel

: Stable Cutting
: General Cutting
Stainless Steel
Honing :
E : Round

Hardened Steel
BS
AOMT184804PEER-M M E
a a a a a a a
18
4.8
1.8 0.4
a a a a a a a
18
4.8
1.4 0.8
a a a
18
4.8
1.0 1.0
a a a
18
4.8
0.8 1.2
a a a a a a a
18
4.8
0.4 1.6
18
4.8
0.4 2.0
a a a
Geometry
RE
AOMT184804PEER-H
M E
a a a a a a a a
18
4.8
1.8 0.4
AOMT184808PEER-H
M E
a a a a a a a a
18
4.8
1.4 0.8
AOMT184816PEER-H
M E
a a a a a a a a
18
4.8
0.4 1.6
AOMT184832PEER-H
M E
a a
18
4.8
0.4 3.2
AOMT184840PEER-H
M E
a a
18
4.8
0.4 4.0
AOMT184850PEER-H
M E
a a
18
4.8
5.0
AOMT184864PEER-H
M E
a a
18
4.8
6.35
L
15
W1
W1
RE
L
15
W1

H Breaker
BS
General
M Breaker
Order Number
Dimensions (mm)
Class
Honing
MC5020
N
MP6120 EW
N
MP6130 EW
N
MP7130 EW
N
MP9120 EW
N
MP9130 EW
VP15TF
VP20RT
Coated
Shape
: Unstable Cutting
Cast Iron
BS
Work
Material
P
M
K
S
H
RE
Nose R is different from the workpiece of R shape depending on the axial rake angle of the body.
* Consult
us for more details.
NOTE ON USE OF INSERTS WITH LARGE CORNER RADII

When using inserts with corner radius RE> R3.2,
please machine the holder with a radius form as shown
on the right.
RE
R (mm)
3.2
4.0
5.0
6.35
2.0
2.5
3.5
5.0
R : Holder end radius

RE : Insert corner radius
MILLING
RE (mm)
SCREW-IN ARBORS
SPARE PARTS
TECHNICAL DATA
L145
P001
Q001
L055
INDEXABLE MILLING
y CUTTING SPEED
Work Material
M
K
S
Hardness
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180350HB
Stainless Steel
Gray Cast Iron
Ductile, Cast Iron
< 350MPa
< 800MPa
Titanium Alloy
< 350HB
Hardened Steel
4055HRC
< 270HB
Insert
Grade
Breaker
MP6120
MP6130
MP6120
MP6130
MP7130
MC5020
MC5020
MP9120
MP9130
MP9120
MP9130
VP15TF
VP15TF
VP20RT
VP15TF
VP20RT
VP20RT
VP15TF
VP15TF
VP15TF
VP20RT
VP15TF
VP20RT
M
M
M
M
M
H
H
H
H
H
H
H
H
H
H
H
H
M
M
M
M
<0.25DC
230(180270)
200(150240)
180(140210)
150(110180)
180(140210)
250(200300)
130(100150)
50(4070)
40(3060)
40(3060)
30(2040)
90(70100)

0.250.5DC
0.50.75DC
220(170260)
190(140230)
170(130200)
140(100170)
170(130200)
240(190290)
120(90140)
180(140210)
150(110180)
140(110160)
110(80130)
140(110160)
210(160260)
100(80120)
85(60100)
70(5080)
DC (Slot)
180(140210)
150(110180)
140(110160)
110(80130)
140(110160)
140(110160)
100(80120)
50(4070)
40(3060)
40(3060)
30(2040)
70(5080)

Work Material
Hardness
Cutting Width
ae (mm)
<5
< 0.5DC
Mild Steel
Carbon Steel
Alloy Steel
< 180HB
180350HB
0.50.75DC
DC (Slot)
M
< 0.5DC
Stainless Steel
< 270HB
MILLING
0.50.75DC
DC (Slot)
K
< 0.5DC
Gray Cast Iron
Tensile Strength
< 350MPa
0.50.75DC
DC (Slot)
< 0.5DC
Ductile, Cast Iron
Tensile Strength
< 800MPa
0.50.75DC
DC (Slot)
L056
Depth of Cut
ap (mm)
57.5
7.510
1012.5
12.515
<5
510
1015
<5
57.5
7.510
<5
57.5
7.510
1012.5
12.515
<5
510
1015
<5
57.5
7.510
<5
57.5
7.510
1012.5
12.515
<5
510
1015
<5
57.5
7.510
<5
57.5
7.510
1012.5
12.515
<5
510
1015
<5
57.5
7.510
2540
Feed per Tooth fz (mm/t.)

5080
100160
0.30
0.25
0.20
0.15
0.10
0.20
0.15
0.10
0.15
0.10
0.07
0.30
0.25
0.20
0.15
0.10
0.20
0.15
0.10
0.15
0.10
0.07
0.30
0.25
0.20
0.15
0.10
0.20
0.15
0.10
0.15
0.10
0.07
0.25
0.20
0.15
0.10
0.07
0.20
0.15
0.10
0.15
0.10
0.07
0.30
0.25
0.20
0.15
0.10
0.20
0.15
0.10
0.15
0.10
0.07
0.25
0.20
0.15
0.10
0.07
0.15
0.10
0.07
0.15
0.10
0.07
0.30
0.25
0.20
0.15
0.10
0.20
0.15
0.10
0.15
0.10
0.07
0.25
0.20
0.15
0.10
0.07
0.20
0.15
0.10
0.15
0.10
0.07
0.25
0.20
0.15
0.10
0.07
0.15
0.10
0.07
0.15
0.10
0.07
0.25
0.20
0.15
0.10
0.07
0.15
0.10
0.07
0.15
0.10
0.07
0.25
0.20
0.15
0.10
0.07
0.15
0.10
0.07
0.15
0.10
0.07
0.25
0.20
0.15
0.10
0.07
0.15
0.10
0.07
0.15
0.10
0.07
Work Material
Cutting Width
ae (mm)
Hardness
Depth of Cut
ap (mm)
2540

5080
100160
0.15
0.10
0.05
0.05
0.10
0.05
0.15
0.10
0.07
0.10
0.07
0.07
0.07
0.10
0.05
0.05
0.05
0.05
0.15
0.10
0.07
0.10
0.07
0.07
0.07
0.10
0.05
0.05
0.05
0.05
0.15
0.10
0.07
0.10
0.07
0.07
0.07
<5
Titanium Alloy
57.5
7.510
<5
<2
<1
<5
57.5
7.510
<5
57.5
<5
<5
< 0.25DC
<350HB
DC (Slot)
< 0.25DC
DC (Slot)
H
< 0.25DC
Hardened Steel
4055HRC
0.250.5DC
0.50.75DC
DC (Slot)
(Note 1) These cutting conditions are a guide to the standard shank type and the arbor type.
Please make adjustments according to the machining conditions.
(Note 2) Vibration is liable to occur in certain cases. Please reduce the depth of cut and / or reduce cutting conditions in the following cases.
When using the long shank type and extra long shank type.
When using long tool overhang with the standard or arbor type.
When the application has poor clamping rigidity or when using a low rigidity machine.
(Note 3) In case of coarse and fine pitch cutters, the coarse pitch type is recommended to prevent vibration.
(Note 4) For heavy interrupted and unstable cutting, the H breaker is first recommendation.
a RAMPING
a HELICAL CUTTING
L
Blind holes,
Flat bottom
Through holes
Pitch
(P)
Pitch
(P)
L=
APMX
tan %
RMPX
DC
Refer to the table below for cutting conditions. For feed per tooth and cutting speed,
follow the cutting conditions for slot milling.
Cutting Edge
Diameter
DC
(mm)
25
28
32
35
40
50
63
80
100
125
160
DC
DC
Hole
diameter
(DH)
Hole
diameter
(DH)
Ramping
Maximum
Maximum Hole
Maximum
Minimum Hole
Maximum
Minimum
Ramping Angle
Diameter 2
Pitch
Diameter
Pitch
Distance 1
P max.
P max.
L
DH max.
DH min.
(mm)
(mm)
(mm)
(mm)
(mm)
RMPX
11
9
85
105
48
54
14
12
45
51
12
11
135
62
11
59
158
68
10
65
158
78
12
75
238
98
10
95
318
124
10
477
158
1.5
636
1
1
954
954
MILLING
APMX

Minimum Hole
Maximum
Diameter
Pitch
P max.
DH min.
(mm)
(mm)
32
38
4
4
10
46
52
11
62
82
121
108
155
142
198
195
182
248
318
6
8
245
315
6
8
232
302
5
7
(Note) When machining highly ductile materials with ramping angles above, chips could be continuous.
In this case, decrease the ramping angle or feed per tooth.
1 L (=15 / tan %). Cutters' moving distance until depth of cut reaches 15mm at a maximum ramping angle.
2 In case corner radius of 0.8mm. Other than that, find with the below formula.
{(cutting edge diameter DC) (corner radius) 0.2}2
*
*
L057
INDEXABLE MILLING
DEEP SHOULDER
MILLING
Finishing
APX4000
K
Cast Iron
DCON
M
Stainless Steel
LONG CUTTING EDGE

DC
P
Steel
Roughing
APMX
LH

coolant holes.
LF
*1 Combination
Shank
y SHANK TYPE
APX4KR4008SA42S056A
40
42
160
80
56
TPS43
TIP15W
APX4KR4012SA42S056A
12
40
42
160
80
56
TPS43
TIP15W
12
50
50.8
160
80
56
TPS43
TIP15W
18
50
50.8
190
110
84
TPS43
TIP15W
Order Number
*1 APX4KR5012WA508S056A
*1 APX4KR5018WA508M084A
Total
Stock
R
Number of Flutes
*2
Dimensions(mm)
DC
DCON
LF
LH
APMX Clamp Screw
Wrench
Insert
AOMT1848ppPEER-p
(Note 1) When using inserts with corner radius RE>3.2, machining of the holder is required as shown on page L055.
(Note 2) Only corner radius RE 0.4mm and 0.8mm can be used for the peripheral cutting edges expect the bottom cutting edge (the end cuttting edge).
L8
DC
DAH
KWW
DCON
BD
CBDP
Cutter Diameter
DC
Set Bolt
&50
HSC10050
&63
12070
APMX
LF
DC
APX4K-050A09A042RA
APX4KR06316CA056A
4 16 63
Dimensions(mm)
Total
Order Number
Stock
Number of Flutes
MILLING
y SHELL TYPE
9 50
Geometry
APMX Clamp Screw Wrench Anti-seize

Lubricant
LF DCON CBDP DAH BD KWW
L8
65 22
22
11 48
6.3
42
TPS43
85 25.4
26
13 60.7
56
TPS43
10.4
9.5
Insert
TIP15W MK1KS AOMT1848

TIP15W MK1KS ppPEER-p
Clamp Torque (N m) : TPS43=3.5
For metric arbor
Dimensions(mm)
Total
Order Number
Stock
Number of Flutes
DC
APMX Clamp Screw Wrench Anti-seize

Lubricant
LF DCON CBDP DAH BD KWW
L8
6.3
42
TPS43
56
TPS43
APX4K-050A09A042RA
9 50
65
22
22
11 48
APX4K-063A16A056RA
4 16 63
85
27
28
13 60.7 12.4
10.4
Insert
TIP15W MK1KS AOMT1848

TIP15W MK1KS ppPEER-p
(Note 1) When using inserts with corner radius RE>3.2, machining of the holder is required as shown on page L055.
(Note 2) Only corner radius RE 0.4mm and 0.8mm can be used for the peripheral cutting edges expect the bottom cutting edge (the end cuttting edge).
(Note 4) In case of internal coolant supply, please use a face mill arbor with through coolant channels. Regular center-thru or side-thru arbors can't be used.
L058

y CUTTING SPEED
Work Material
M
K
S
Hardness
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180350HB
Stainless Steel
Gray Cast Iron
Ductile, Cast Iron
< 350MPa
< 800MPa
Titanium Alloy
< 350HB
< 270HB
Insert
Grade
Breaker
MP6120
MP6130
MP6120
MP6130
MP7130
MC5020
MC5020
MP9120
MP9130
MP9120
MP9130
VP15TF
VP20RT
VP15TF
VP20RT
VP15TF
VP15TF
VP15TF
VP15TF
VP20RT
VP15TF
VP20RT
M
M
M
M
M
H
H
H
H
H
H
H
H
H
H
H
M
M
M
M
<0.15DC
200(160250)
170(130220)
160(120200)
130(90170)
160(120200)
230(180280)
190(140220)
50(4070)
40(3060)
40(3060)
30(2040)

0.150.3DC
160(120200)
130(90170)
120(100140)
90(70110)
120(100140)
190(140240)
170(120220)
DC (Slot)
140(120160)
110(90130)
100(80120)
70(5090)
100(80120)
190(140240)
170(120220)
50(4070)
40(3060)
40(3060)
30(2040)

Hardness
Cutting Width
ae (mm)
P
< 0.3DC
Mild Steel
<180HB
DC (Slot)
Carbon Steel
Alloy Steel
< 0.3DC
180350HB
DC (Slot)
M
Stainless Steel
< 270HB
< 0.3DC
DC (Slot)
K
< 0.15DC
Gray Cast Iron
Tensile Strength
<350MPa
0.150.3DC
DC (Slot)
< 0.15DC
Ductile, Cast Iron
Tensile Strength
< 800MPa
0.150.3DC
DC (Slot)
S
Titanium Alloy
<350HB
< 0.15DC
DC (Slot)
< 0.15DC
DC (Slot)
Depth of Cut
ap (mm)
< 20
2050
5080
< 20
2050
< 20
2050
5080
< 20
2050
< 20
2050
5080
<10
<10
1050
5080
<10
1050
5080
<10
1050
< 20
2050
5080
< 20
2050
5080
<10
1050
< 20
2050
<50
<10
< 20
40 Length of cut 56mm 50 Length of cut 56mm 50 Length of cut 84mm

50 Length of cut 42mm 63 Length of cut 56mm
0.25
0.20
0.25
0.20
0.20
0.15
0.25
0.20
0.20
0.15
0.25
0.20
0.15
0.10
0.25
0.20
0.15
0.10
0.25
0.20
0.10
0.30
0.25
0.10
0.30
0.25
0.25
0.20
0.25
0.20
0.25
0.20
0.25
0.20
0.25
0.20
0.25
0.20
0.20
0.15
0.20
0.15
0.15
0.10
0.10
0.10
0.08
0.07
0.05
0.15
0.10
0.10
0.10
0.08
0.07
0.05
0.20
0.15
0.10
0.15
0.20
0.15
0.10
0.10
0.20
0.15
0.10
0.07
0.25
0.20
0.15
0.20
0.15
0.10
0.20
0.15
0.20
0.15
0.10
0.15
0.10
0.07
0.10
MILLING
Work Material

(Note) The above cutting conditons are determined based on high rigidity machine and workpiece, where no vibration occurred. Please adjust
processing conditions if the vibration is generated.
SPARE PARTS
TECHNICAL DATA
P001
Q001
L059
INDEXABLE MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
<ALUMINIUM ALLOY TO DIFFICULT-TO-CUT MATERIAL CUTTING>
Finishing
Roughing
AXD4000
K
Fig.1
DCON
DC
Non-ferrous Metal Heat Resistant Alloy
APMX
LH
LF
DC
DCON
Fig.2
APMX
LH
LF
AXD4000R201SA20SA
20 110 35
20 15.5 15000
AXD4000R252SA25SA
25 125 50
AXD4000R252SA25LA
AXD4000R282SA25SA
AXD4000R282SA25ELA
AXD4000R322SA32SA
A Type
MILLING
3.2
B Type
4.0
5.0
*
Clamp
Screw
Wrench
Anti-seize
Lubricant
TS3SBS
TKY08D
MK1KS
25 15.5 49000
TS3SB
TKY08D
MK1KS
25 170 80
25 15.5 49000
TS3SB
TKY08D
MK1KS
28 125 50
25 15.5 48500
TS3SB
TKY08D
MK1KS
28 220 50
25 15.5 48500
TS3SB
TKY08D
MK1KS
32 150 50
32 15.5 48000
TS3SB
TKY08D
MK1KS
AXD4000R322SA32LA
32 200 80
32 15.5 48000
TS3SB
TKY08D
MK1KS
AXD4000R352SA32SA
35 150 50
32 15.5 45000
TS3SB
TKY08D
MK1KS
AXD4000R352SA32ELA
35 250 50
32 15.5 45000
TS3SB
TKY08D
MK1KS
AXD4000R403SA32SA
40 150 50
32 15.5 41000
TS3SB
TKY08D
MK1KS
AXD4000R403SA42SA
40 170 80
42 15.5 41000
TS3SB
TKY08D
MK1KS
AXD4000R403SA32ELA
40 250 50
32 15.5 41000
TS3SB
TKY08D
MK1KS
AXD4000R201SA20SB
20 110 35
20 14.8 15000
TS3SBS
TKY08D
MK1KS
AXD4000R252SA25SB
25 125 50
25 14.8 49000
TS3SB
TKY08D
MK1KS
AXD4000R252SA25LB
25 170 80
25 14.8 49000
TS3SB
TKY08D
MK1KS
AXD4000R282SA25SB
28 125 50
25 14.8 48500
TS3SB
TKY08D
MK1KS
AXD4000R282SA25ELB
28 220 50
25 14.8 48500
TS3SB
TKY08D
MK1KS
AXD4000R322SA32SB
32 150 50
32 14.8 48000
TS3SB
TKY08D
MK1KS
AXD4000R322SA32LB
32 200 80
32 14.8 48000
TS3SB
TKY08D
MK1KS
AXD4000R352SA32SB
35 150 50
32 14.8 45000
TS3SB
TKY08D
MK1KS
AXD4000R352SA32ELB
35 250 50
32 14.8 45000
TS3SB
TKY08D
MK1KS
AXD4000R403SA32SB
40 150 50
32 14.8 41000
TS3SB
TKY08D
MK1KS
AXD4000R403SA42SB
40 170 80
42 14.8 41000
TS3SB
TKY08D
MK1KS
AXD4000R403SA32ELB
40 250 50
32 14.8 41000
TS3SB
TKY08D
MK1KS
RE
0.4
Max.
Allowable
Revolution
(min-1)
Type(Fig.)
DC
Dimensions(mm)
APMX (mm)
Order Number
Stock
Insert
Corner
Radius
Number of Teeth
Type
y SHANK TYPE
LF
LH DCON
Before operating the tool read the operational guidance on page L071.
(Note 2) When using the tool at high spindle speeds, ensure that the tool and chuck are correctly balanced.
(Note 3) Note for inserts with a corner radius of 1.6 and above, as corner radius increases the LF and LH dimensions decrease.
Clamp Torque (N m) : TS3SBS=1.5, TS3SB=1.5
Use the clamp screw by setting the bundled screw.
*
*
L060
Insert
XDGX1750pp
PDpR-pp
&40
&80
a
a
a
a
a
a
a
a
15.5
15.5
15.5
15.5
15.5
15.5
15.5
15.5
14.8
14.8
14.8
14.8
14.8
14.8
14.8
14.8
41000
41000
35000
35000
30000
27000
23000
20000
41000
41000
35000
35000
30000
27000
23000
20000
Max.
Allowable
Revolution
(min-1)
15.5
15.5
15.5
15.5
15.5
15.5
15.5
15.5
14.8
14.8
14.8
14.8
14.8
14.8
14.8
14.8
41000
41000
35000
35000
30000
27000
23000
20000
41000
41000
35000
35000
30000
27000
23000
20000
1
1
2
2
2
2
2
3
1
1
2
2
2
2
2
3
KWW
BD
WT 2
8.5
8.5
11
11
11
13
17
8.5
8.5
11
11
11
13
17
Type(Fig.)
18
18
20
20
20
26
32
40
18
18
20
20
20
26
32
40
APMX (mm)
16
16
22
22
22
25.4
31.75
38.1
16
16
22
22
22
25.4
31.75
38.1
APMX (mm)
50
50
50
50
50
50
63
63
50
50
50
50
50
50
63
63
34 8.4
34 8.4
45 10.4
45 10.4
50 10.4
60 9.5
70 12.7
90 15.9
34 8.4
34 8.4
45 10.4
45 10.4
50 10.4
60 9.5
70 12.7
90 15.9
(kg)
5.6
5.6
6.3
6.3
6.3
6
8
10
5.6
5.6
6.3
6.3
6.3
6
8
10
12
12
17
17
17
20
26
56
12
12
17
17
17
20
26
56
0.3
0.3
0.4
0.4
0.6
1.0
2.0
2.8
0.3
0.3
0.4
0.4
0.6
1.0
2.0
2.8
Geometry
HFF08043H
HSC10030H
12035H
16040H
MBA20040H
Max.
Allowable
Revolution
(min-1)
DCCB
40
40
50
50
63
80
100
125
40
40
50
50
63
80
100
125
& 125
Set Bolt
WT 2
2
3
2
4
5
5
6
7
2
3
2
4
5
5
6
7
& 100
L8
DAH
Stock
a
CBDP
5.0
DCON
4.0
AXD4000-040A02RA
AXD4000-040A03RA
AXD4000-050A02RA
AXD4000-050A04RA
AXD4000-063A05RA
AXD4000R08005CA
AXD4000R10006DA
AXD4000R12507EA
AXD4000-040A02RB
AXD4000-040A03RB
AXD4000-050A02RB
AXD4000-050A04RB
AXD4000-063A05RB
AXD4000R08005CB
AXD4000R10006DB
AXD4000R12507EB
LF
3.2
DC
0.4
B Type
A Type
RE
Number of Teeth
Type
Insert Corner Radius
Order Number
LF
&50, &63
Dimensions(mm)
APMX
APMX
DCCB
DC
Cutter Diameter
DC
y ARBOR TYPE
CBDP
LF
LF
DC
KAPR :0
GAMP :+14 15
T :+21 +26
GAMF :+21 +26 I :+14 +15
L8
L8
125
DAH
DCCB
APMX
DAH
DCCB
DC
BD
DCON
KWW
Fig. 3
CBDP
L8
50
63
80
100
CBDP
40
BD
DCON
KWW
Fig. 2
DCON
KWW
Type(Fig.)
Fig. 1 BD
1
1
2
2
2
2
2
3
1
1
2
2
2
2
2
3
x
c
*1
Clamp
Screw
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
Wrench Anti-seize
Insert
Lubricant
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS XDGX1750pp
TKY08D MK1KS PDpR-pp
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
METRIC Standard
a
a
a
a
a
a
a
a
a
a
a
a
50
50
50
50
50
50
63
63
50
50
50
50
50
50
63
63
16
16
22
22
22
27
32
40
16
16
22
22
22
27
32
40
18
18
20
20
20
23
26
40
18
18
20
20
20
23
26
40
8.5
8.5
11
11
11
13
17
8.5
8.5
11
11
11
13
17
*
KWW
BD
34 8.4
34 8.4
45 10.4
45 10.4
50 10.4
60 12.4
78 14.4
90 16.4
34 8.4
34 8.4
45 10.4
45 10.4
50 10.4
60 12.4
78 14.4
90 16.4
(kg)
5.6
5.6
6.3
6.3
6.3
7
8
9
5.6
5.6
6.3
6.3
6.3
7
8
9
12
12
17
17
17
20
26
56
12
12
17
17
17
20
26
56
0.3
0.3
0.4
0.4
0.6
1.0
2.0
2.8
0.3
0.3
0.4
0.4
0.6
1.0
2.0
2.8
*1
Clamp
Screw
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
TS3SB
Wrench Anti-seize
Insert
Lubricant
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS XDGX1750pp
TKY08D MK1KS PDpR-pp
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
TKY08D MK1KS
MILLING
40
40
50
50
63
80
100
125
40
40
50
50
63
80
100
125
DCCB
2
3
2
4
5
5
6
7
2
3
2
4
5
5
6
7
Dimensions(mm)
L8
DAH
CBDP
5.0
DCON
4.0
AXD4000-040A02RA
AXD4000-040A03RA
AXD4000-050A02RA
AXD4000-050A04RA
AXD4000-063A05RA
AXD4000-080A05RA
AXD4000-100A06RA
AXD4000-125B07RA
AXD4000-040A02RB
AXD4000-040A03RB
AXD4000-050A02RB
AXD4000-050A04RB
AXD4000-063A05RB
AXD4000-080A05RB
AXD4000-100A06RB
AXD4000-125B07RB
LF
3.2
DC
0.4
B Type
A Type
RE
Stock
Order Number
Number of Teeth
Type
For metric arbor
(Note 1) The maximum allowable spindle speeds are set to ensure tool and insert stability.
Before operating the tool read the operational guidance on page L071.
(Note 3) Note for inserts with a corner radius of 1.6 and above, as corner radius increases the LF dimension decrease.
1 Clamp Torque (N m) : TS3SB=1.5
1 Use the clamp screw by setting the bundled screw.
2 WT : Tool Weight
*
*
*
SPARE PARTS
TECHNICAL DATA
P001
Q001
L061
INDEXABLE MILLING
INSERTS
Aluminium Alloy
Cutting Conditions (Guide):

:Stable Cutting
:General Cutting
Titanium Alloy
Honing:
F :Sharp
Work Material
Order Number
XDGX175004PDFR-GL
XDGX175008PDFR-GL
XDGX175012PDFR-GL
XDGX175016PDFR-GL
XDGX175020PDFR-GL
XDGX175024PDFR-GL
XDGX175030PDFR-GL
XDGX175032PDFR-GL
XDGX175040PDFR-GL
XDGX175050PDFR-GL
XDGX175004PDER-GM
XDGX175008PDER-GM
XDGX175012PDER-GM
XDGX175016PDER-GM
XDGX175020PDER-GM
XDGX175024PDER-GM
XDGX175030PDER-GM
XDGX175032PDER-GM
XDGX175040PDER-GM
XDGX175050PDER-GM
XDGX175004PDFR-GM
XDGX175008PDFR-GM
XDGX175012PDFR-GM
XDGX175016PDFR-GM
XDGX175020PDFR-GM
XDGX175024PDFR-GM
XDGX175030PDFR-GM
XDGX175032PDFR-GM
XDGX175040PDFR-GM
XDGX175050PDFR-GM
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
F
F
F
F
F
F
F
F
F
F
E
E
E
E
E
E
E
E
E
E
F
F
F
F
F
F
F
F
F
F
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
E :Round
Dimensions (mm)
INSL
BS
RE
23.0
23.0
23.0
22.0
22.0
22.0
21.1
21.1
20.0
19.4
23.0
23.0
23.0
22.0
22.0
22.0
21.1
21.1
20.0
19.4
23.0
23.0
23.0
22.0
22.0
22.0
21.1
21.1
20.0
19.4
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
1.7
1.3
0.9
1.4
1.0
0.6
0.8
0.6
0.8
0.4
1.7
1.3
0.9
1.4
1.0
0.6
0.8
0.6
0.5
0.4
1.7
1.3
0.9
1.4
1.0
0.6
0.8
0.6
0.5
0.4
0.4
0.8
1.2
1.6
2.0
2.4
3.0
3.2
4.0
5.0
0.4
0.8
1.2
1.6
2.0
2.4
3.0
3.2
4.0
5.0
0.4
0.8
1.2
1.6
2.0
2.4
3.0
3.2
4.0
5.0
TF15
Shape
Class
Honing
LC15TF
MP9120
Stock
Coated Carbide
:Unstable Cutting
Geometry
RE
BS
20
S
30
INS
L
MILLING
careful because corner R(RE) has a different shape than machined workpiece R.
* Be
When a GM breaker is recommended, stress the dimensional precision of the workpiece shape.
y Holder And Insert Corner Radius Combination

Holder
R0.4
Applicable
Insert
Corner R
(RE)
R0.8
R1.2
A Type Holder
B Type Holder
AXD4000pppppppA
AXD4000RppppppppA
AXD4000pppppppB
AXD4000RppppppppB
R1.6
R2.0
L062
R3.0
R3.2
R4.0
R5.0
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
175004PDpR-pp 175008PDpR-pp 175012PDpR-pp 175016PDpR-pp 175020PDpR-pp 175024PDpR-pp 175030PDpR-pp 175032PDpR-pp 175040PDpR-pp 175050PDpR-pp
Not interchangeable with the corresponding inserts of the A type and B type holders.
R2.4

Grade
Breaker
Cutting
Speed
vc
(m/min)
(mm)
<0.25
<0.5
TF15
Si<5%
(A6061, A7075 etc)
LC15TF
Aluminium Alloy
GL
DC
DC
(mm)
<0.05
<0.2
<0.05
<0.15
<5
<0.05
<0.25
<10
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<0.05
<10
<10
<14.5
<5
DC
<10
<14.5
<5
<0.5
Aluminium Alloy
Si<5%
TF15
MP9120
GM
DC
<10
<14.5
1000
(200 3000)
<5
<0.75
DC
<10
<14.5
<5
DC(Slot)
<10
<14.5
<5
<0.25
DC
<10
<14.5
<5
Aluminium Alloy
(AC4B etc)
Aluminium Alloy
<0.5
5%<Si<10%
MP9120
Si>10%
GM
DC
<5
<0.75
(ADC12, A390 etc)
<10
<14.5
200
(200 3000)
DC
<10
<14.5
<5
DC(Slot)
<10
<14.5
<5
<0.25
DC
<10
<14.5
<5
<0.5
Titanium Alloy
(Ti-6Al-4V etc)
MP9120
GM
DC
<10
<14.5
40
(30 60)
<5
<0.75
DC
<10
<14.5
<5
DC(Slot)
&40
<14.5
<5
<0.25
&25 &28 &32 &35
<10
<14.5
DC(Slot)
&20
<0.05
<5
DC
Cutting Edge Diameter DC
<5
<14.5
1000
(200 3000)
<0.75
(A6061, A7075 etc)
Feed per Tooth (mm/t.)
Cutting Width Depth of Cut

ae
ap
<10
<14.5
&50&125
<0.25
<0.2
<0.15
<0.25
<0.2
<0.15
<0.25
<0.35
<0.35
<0.4
<0.4
<0.3
<0.3
<0.35
<0.35
<0.25
<0.25
<0.3
<0.3
<0.35
<0.35
<0.35
<0.4
<0.3
<0.3
<0.3
<0.35
<0.2
<0.25
<0.25
<0.3
<0.3
<0.3
<0.3
<0.35
<0.25
<0.25
<0.25
<0.3
<0.2
<0.2
<0.2
<0.25
<0.25
<0.25
<0.3
<0.35
<0.35
<0.3
<0.25
<0.35
<0.3
<0.2
<0.3
<0.25
<0.2
<0.25
<0.35
<0.3
<0.25
<0.35
<0.3
<0.25
<0.3
<0.25
<0.2
<0.25
<0.4
<0.35
<0.3
<0.35
<0.3
<0.25
<0.3
<0.25
<0.2
<0.3
<0.4
<0.35
<0.3
<0.4
<0.35
<0.3
<0.35
<0.3
<0.25
<0.35
<0.1
<0.1
<0.1
<0.08
<0.1
<0.1
<0.1
<0.08
<0.1
<0.1
<0.1
<0.08
<0.1
<0.1
<0.1
<0.05
<0.08
<0.1
<0.1
<0.05
<0.08
<0.1
<0.1
<0.05
<0.08
<0.1
<0.1
<0.05
<0.05
<0.05
<0.05
MILLING
Work Material
(Note 1) The above cutting conditions are determined based on high workpiece and machine rigidity, where no vibration occurred.
If vibrations occur make adjustments according to the machining conditions.
(Note 2) Note, vibrations may occur in the following conditions.
When using long tool overhang.
When pocket machining corner radii.
When the workpiece has poor clamping rigidity or when the machine rigidity or workpiece rigidity is low, vibrations can occur easily,
if so, reduce cutting conditions such as width and depth of cut and feed per tooth.
SPARE PARTS
TECHNICAL DATA
P001
Q001
L063
INDEXABLE MILLING
a RAMPING
Blind holes,
Flat bottom
a HELICAL
CUTTING
L=
Through holes
Pitch
(P)
Pitch
(P)
APMX
tan %
RMPX
APMX
DC
DC
RAMPING/HELICAL CUTTING
Holder
Type
Cutting Edge
Diameter
DC
(mm)
20
25
28
32
35
A type
40
50
63
80
MILLING
100
L064
125
Insert
Corner R
RE
(mm)
0.41.2
1.6 2.4
3.0 3.2
0.4 1.2
1.62.4
3.03.2
0.41.2
1.62.4
3.03.2
0.41.2
1.62.4
3.03.2
0.41.2
1.62.4
3.03.2
0.41.2
1.62.4
3.0 3.2
0.4 1.2
1.62.4
3.03.2
0.41.2
1.62.4
3.03.2
0.41.2
1.62.4
3.03.2
0.41.2
1.62.4
3.03.2
0.41.2
1.62.4
3.03.2
DC
Hole
diameter
(DH)
Hole
diameter
(DH)
Helical Milling (Blind Hole, Flat Bottom)
Ramping
Helical Milling
Minimum Distance Maximum Hole Diameter Maximum Pitch Minimum Hole Diameter Maximum Pitch Minimum Hole Diameter Maximum Pitch
Maximum
L 1
DH max.
P max.
DH min.
P max.
DH min.
P max.
Ramping Angle
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RMPX
20.7
19.9
18.9
23.1
22.0
18.7
19.2
18.5
16.7
15.4
14.7
13.8
13.4
12.7
11.8
11.1
10.4
9.7
8.2
7.6
6.9
6.1
5.6
5.2
4.6
4.2
3.8
3.5
3.2
2.9
2.7
2.5
2.3
42
43
46
37
39
46
45
47
52
57
60
64
66
69
75
80
85
91
108
117
129
146
159
171
193
212
234
254
278
306
329
356
386
37.1
34.7
33.1
47.1
44.7
43.1
53.1
50.7
49.1
61.1
58.7
57.1
67.1
64.7
63.1
76.7
74.3
72.7
96.7
94.3
92.7
122.7
120.3
118.7
156.7
154.3
152.7
196.7
194.3
192.7
246.7
244.3
242.7
*23
*4
*2
*3
*4
*2
*3
*4
*2
*
*34
*2
*3
*4
*2
*3
*4
*2
*3
*4
*2
*3
*4
*2
*3
*
*42
*3
*4
*2
*3
*4
*
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
36.1
34.6
33.3
46
44.4
43
52
50.4
48.9
59.9
58.3
56.8
65.8
64.3
62.8
75.9
74.2
72.7
95.6
94
92.4
121.6
119.9
118.4
155.6
153.9
152.4
195.5
193.9
192.3
245.5
243.8
242.3
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
14
13
12
22
22
22
32
32
32
36
36
36
46
46
46
50
50
50
62
62
62
81
81
81
107
107
107
141
141
141
181
181
181
231
231
231
2
2
1
8
8
7
8
8
7
11
11
10
11
10
9
13
12
11
14
13
11
14
13
12
14
13
12
14
13
12
14
13
12
Holder
Type
Cutting Edge
Diameter
DC
(mm)
20
25
28
32
35
B type
40
50
63
80
100
125
Insert
Corner R
RE
(mm)
4
5
4
5
4
5
4
5
4
5
4
5
4
5
4
5
4
5
4
5
4
5
Helical Milling (Blind Hole, Flat Bottom)
Ramping
Helical Milling
Maximum
L 1
DH max.
P max.
DH min.
P max.
DH min.
P max.
Ramping Angle
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RMPX
17.5
16.6
15.1
13.7
14.1
13
12.7
12
10.8
10.2
8.8
8.2
6.3
5.8
4.6
4.2
3.4
3.1
2.6
2.4
2
1.8
47
71
55
61
59
65
66
70
78
83
96
103
135
146
184
202
250
274
326
354
424
471
31.5
29.5
41.5
39.5
47.5
45.5
55.5
53.5
61.5
59.5
71.1
69.1
91.1
89.1
117.1
115.1
151.1
149.1
191.1
189.1
241.1
239.1
10
6
10
9
10
9
10
9
10
9
10
9
10
9
10
9
10
9
10
9
10
9
31.8
31.1
41.4
40.6
47.2
46.4
55.1
54.3
61
60.2
70.9
70.1
90.6
89.8
116.6
115.7
150.5
149.6
190.5
189.6
240.5
239.6
10
7
10
9
10
9
10
9
10
9
10
9
10
9
10
9
10
9
10
9
10
9
22
22
32
32
36
36
46
46
50
50
62
62
81
81
107
107
141
141
181
181
231
231
1
1
5
5
6
5
9
8
8
8
10
9
10
9
10
9
10
9
10
9
10
9
(Note 1) The recommended ramping feed is 0.05mm/tooth or under.

1) Using the maximum ramping angle, the distance to reach the maximum depth of cut is as follows:
L= (maximum depth of cut APMX/tan %). Maximum depth of cut A type is 15.5mm, B type is 14.8mm.
2) Corner radius of 1.2mm. For other corner radii, use the following formula. {(cutting edge diameter DC)(corner radius RE) 0.25}2
MILLING
*
*
*
*
y Max.Drilling Depth
Type
A type
B type
Max.Drilling Depth (mm)
Insert
Corner R
RE
(mm)
&20
&25
&28
&32
&35
&40 &125
0.4
0.8
1.2
1.6
2.0
2.4
3.0
3.2
4.0
5.0
5.3
5.3
5.3
4.8
4.8
4.8
4.3
4.3
3.7
3.4
5.2
5.2
5.2
4.6
4.6
4.6
3.7
3.7
2.7
2.3
5.2
5.2
5.2
4.7
4.7
4.7
4.2
4.2
3.7
3.3
5.2
5.2
5.2
4.7
4.7
4.7
4.2
4.2
3.6
3.3
5.3
5.3
5.3
4.9
4.9
4.9
4.4
4.4
3.8
3.5
5.3
5.3
5.3
4.8
4.8
4.8
4.4
4.4
3.8
3.5
AXD4000 can be
effectively used for pocket
machining without the
need for a prepared hole.
L065
INDEXABLE MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
APMX
Non-ferrous Metal

a Low resistance insert and high rigidity
DCCB
DC
DAH
DCCB
DC
design for excellent performance.

Cutter Diameter
DC
&50, &63
&80
KAPR :0
GAMP :+11
T :+26 +29
GAMF :+26 +29 I :+11
Dimensions (mm)
WT
(kg)
Max.
Allowable
Revolution
Geometry
HSC10030H
12035H
16040H
MBA20040H
*1
AXD7000-050A03RA
50 50 22
20 11 45 10.4 6.3 17 0.4 21
0.8 AXD7000-063A03RA
DC LF DCON CBDP DAH BD KWW L8 DCCB
(mm)
(min-1)
Insert
63 50 22
20 11 50 10.4 6.3 17 0.5 21
25000 1 TS4SBL TKY15D MK1KS
AXD7000R08004CA
80 63 25.4
26 13 63
9.5 6
20 1.2 21
3.2
AXD7000R10005DA
5 100 63 31.75 32 17 70 12.7 8
26 1.8 21
AXD7000R12506EA
6 125 63 38.1
40 90 15.9 10
56 2.7 21
16000 2 TS4SBL TKY15D MK1KS XDGX2270pp
AXD7000-050A03RB
50 50 22
20 11 45 10.4 6.3 17 0.4 20.4 30000 1 TS4SBL TKY15D MK1KS
4.0 AXD7000-063A03RB
63 50 22
20 11 50 10.4 6.3 17 0.5 20.4 25000 1 TS4SBL TKY15D MK1KS
AXD7000R08004CB
80 63 25.4
26 13 63
9.5 6
20 1.2 20.4 23000 1 TS4SBL TKY15D MK1KS
5.0
AXD7000R10005DB
5 100 63 31.75 32 17 70 12.7 8
26 1.8 20.4 19000 1 TS4SBL TKY15D MK1KS
AXD7000R12506EB
6 125 63 38.1
56 2.7 20.4 16000 2 TS4SBL TKY15D MK1KS
DC
MILLING
40 90 15.9 10
PDFR-GL
DCON
A Type
&125
Set Bolt
Clamp Wrench Anti-seize

Screw
Lubricant
RE
B Type
&100
APMX
Order Number
Stock
Number of Teeth
Type
y ARBOR TYPE
L8
L8
50
63
80
100
LF
BD
DCON
KWW
APMX
125
CBDP
Fig.2
BD
DCON
KWW
CBDP
Fig.1
LF
AXD7000
Roughing
Type (Fig.)
<FOR ALUMINIUM ALLOY>
Finishing
APMX
LH
LF
AXD7000R322SA32SA
AXD7000R402SA42SA
32
170
80
32
21
41000
Clamp
Screw
TS4SB
TKY15D
Anti-seize
Lubricant
MK1KS
40
170
80
42
21
36000
TS4SBL
TKY15D
MK1KS
AXD7000R322SA32SB
AXD7000R402SA42SB
32
170
80
32
20.4 41000
TS4SB
TKY15D
MK1KS
40
170
80
42
20.4 36000
TS4SBL
TKY15D
MK1KS
RE
B Type A Type
0.8
3.2
4.0
5.0
DC
Order Number
APMX
Insert
Corner
Radius

1
Stock
Number of Teeth
Type
y SHANK TYPE
Dimensions (mm)
LF
LH
DCON (mm)
Max.
Allowable
Revolution
(min-1)
Wrench
Before operating the tool read the operational guidance on L071 page.
(Note 2) When using the tool at high spindle speeds, ensure that the tool and chuck are correctly balanced.
(Note 3) Note for inserts with a corner radius of 3.0 and above, as corner radius increases the LF and LH dimensions decreases.
1 Clamp Torque (N m) : TS4SB=3.5, TS4SBL=3.5
2 WT : Tool Weight
*
*
*
L066
Insert
XDGX2270pp
PDFR-GL
Fig.2
125
BD
DCON
KWW
CBDP
LF
APMX
LF
CBDP
DCCB
DC
DAH
DCCB
DC
Cutter Diameter
DC
&80
Dimensions (mm)
WT
(kg)
Max.
Allowable
Revolution
*1
AXD7000-050A03RA
50 50 22
20 11 45 10.4 6.3 17 0.4 21
0.8 AXD7000-063A03RA
AXD7000-080A04RA
63 50 22
20 11 50 10.4 6.3 17 0.5 21
DC LF DCON CBDP DAH BD KWW L8 DCCB
(mm)
(min-1)
Insert
80 63 27
23 13 63 12.4 7
20 1.2 21
5 100 63 32
26 17 70 14.4 8
26 1.8 21
AXD7000-125B06RA
6 125 63 40
40 90 16.4 9
56 2.7 21
16000 2 TS4SBL TKY15D MK1KS XDGX2270pp
AXD7000-050A03RB
50 50 22
20 11 45 10.4 6.3 17 0.4 20.4 30000 1 TS4SBL TKY15D MK1KS
4.0 AXD7000-063A03RB
63 50 22
20 11 50 10.4 6.3 17 0.5 20.4 25000 1 TS4SBL TKY15D MK1KS
AXD7000-080A04RB
80 63 27
23 13 63 12.4 7
20 1.2 20.4 23000 1 TS4SBL TKY15D MK1KS
5.0
AXD7000-100A05RB
5 100 63 32
26 17 70 14.4 8
26 1.8 20.4 19000 1 TS4SBL TKY15D MK1KS
AXD7000-125B06RB
6 125 63 40
40 90 16.4 9
56 2.7 20.4 16000 2 TS4SBL TKY15D MK1KS
AXD7000-100A05RA
A Type
&125
z
z
Clamp Wrench Anti-seize

Screw
Lubricant
RE
B Type
&100
APMX
Order Number
Stock
Number of Teeth
Type
y ARBOR TYPE
KAPR :0
GAMP :+11
T :+26 +29
GAMF :+26 +29 I :+11
Geometry
HSC10030H
12035H
16040H
MBA20040H
&50, &63
Set Bolt
Type (Fig.)
For metric arbor
APMX
L8
BD
DCON
KWW
L8
Fig.1
50
63
80
100
3.2
PDFR-GL
APMX
LU
MILLING
63
DC
HSK63A
LF
AXD7000R03202A-H63A
32
127
80
21
41000
AXD7000R04002A-H63A
40
132
85
21
36000
TS4SBL
TKY15D
MK1KS
3.2
AXD7000R05003A-H63A
50
137
90
21
30000
TS4SBL
TKY15D
MK1KS
Dimensions (mm)
APMX
0.8
Clamp
Screw
TS4SB
Stock
Number of Teeth
DC
Order Number
RE
A Type

1
Type
y HSK63A SHANK TYPE
LF
LU
(mm)
Max.
Allowable
Revolution
(min-1)
Anti-seize
Lubricant
TKY15D MK1KS
Wrench
Insert
XDGX2270pp
PDFR-GL
(Note 3) Note for inserts with a corner radius of 3.0 and above, as corner radius increases the LF and LU dimensions decreases.
(Note 4) No hole for data carrier.
1 Clamp Torque (N m) : TS4SB=3.5, TS4SBL=3.5
2 WT : Tool Weight
*
*
*
SPARE PARTS
TECHNICAL DATA
P001
Q001
L067
INDEXABLE MILLING
INSERTS
N

: Stable Cutting
: General Cutting
Aluminium Alloy
Order Number
Honing :
F : Sharp
Dimensions(mm)
INSL
BS
RE
Geometry
TF15
Shape
Class
Honing
LC15TF
Stock
Coated Carbide
: Unstable Cutting
XDGX227008PDFR-GL G F
30
22.5
2.0
0.8
30
22.5
1.2
1.6
30
22.5
0.8
2.0
28.8 22.5
0.8
3.0
28.8 22.5
0.6
3.2
27.5 22.5
0.9
4.0
27
0.4
5.0
22.5
RE
BS
Work
Material
20
S
30
INS
L
* Be careful because corner R(RE) has a different shape than machined workpiece R.
y HOLDER AND INSERT CORNER RADIUS COMBINATION
Holder
R0.8
Insert
Corner
Radius
(RE)
A Holder
B Holder
AXD7000pppppppA
AXD7000RppppppppA
AXD7000RppppA-H63A
AXD7000pppppppB
AXD7000RppppppppB
R1.6
R2.0
R3.0
MILLING
L068
R4.0
R5.0
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
XDGX
227008PDFR-GL 227016PDFR-GL 227020PDFR-GL 227030PDFR-GL 227032PDFR-GL 227040PDFR-GL 227050PDFR-GL
Not interchangeable with the corresponding inserts of the A type and B type holders.
R3.2

Work Material
Grade
Breaker
Cutting Speed
vc
(m/min)
Cutting Width
ae
(mm)
N
<0.25
<0.5
Aluminium Alloy
LC15TF
TF15
GL
DC
DC
1000
(200 3000)
<0.75
DC
<DC
Cutting
Depth
ap

(mm)
&32
&40
&50&125
<5
<0.35
<0.40
<0.40
<0.30
<0.35
<0.35
<0.25
<0.30
<0.30
<0.20
<0.25
<0.25
<0.35
<0.35
<0.40
<0.30
<0.30
<0.35
<0.25
<0.25
<0.30
<0.20
<0.20
<0.25
<0.30
<0.30
<0.35
<0.25
<0.25
<0.30
<0.20
<0.20
<0.25
<0.15
<0.15
<0.20
<0.25
<0.30
<0.35
<0.20
<0.25
<0.30
<0.15
<0.20
<0.25
<0.10
<0.15
<0.20
5 10
10 15
15 20
<5
5 10
10 15
15 20
<5
5 10
10 15
15 20
<5
5 10
10 15
15 20
MILLING
(Note 1) The above cutting conditions are determined based on high workpiece and machine rigidity, where no vibration occurred. If vibrations
occur make adjustments according to the machining conditions.
(Note 2) Note, vibrations may occur in the following conditions.
When using long tool overhang.
When the workpiece has poor clamping rigidity or when the machine rigidity or workpiece rigidity is low,vibrations can occur easily, if so, reduce the cutting conditions.
When pocket machining corner radii.
SPARE PARTS
TECHNICAL DATA
P001
Q001
L069
INDEXABLE MILLING
a RAMPING
Blind holes,
Flat bottom
a HELICAL
CUTTING
L=
Through holes
Pitch
(P)
Pitch
(P)
APMX
tan %
RMPX
APMX
DC
DC
RAMPING/HELICAL CUTTING
Type
A type
B type
DC
Hole
diameter
(DH)
Hole
diameter
(DH)
Ramping
Cutting Edge
Diameter
Maximum
DC
1
L
Ramping Angle
DH max. 2
P max.
DH min. 3
P max.
P max.
DH min.
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
RMPX
32
40
50
63
80
100
125
32
40
50
63
80
100
125
19
13
9
7
5
4
3
18
11
8
6
4
3
2
61
91
133
171
240
300
401
63
105
146
195
293
391
587
61.8
77.8
97.8
123.8
157.8
197.8
247.8
55.4
71.4
91.4
117.4
151.4
191.4
241.4
21
18
16
15
16
15
12
16
14
13
11
11
9
12
58.2
74.2
94.2
120.2
154.2
194.2
244.2
54.0
70.0
90.0
116.0
150.0
190.0
240.0
20
17
16
15
15
15
12
16
14
12
11
11
9
12
41
57
77
103
137
177
227
41
57
77
103
137
177
227
(Note) The recommended ramping feed is 0.05mm/tooth or under.

1 L (Max. Depth of Cut =15 / tan %). Cutters' moving distance until depth of cut reaches APMX at a maximum ramping angle.
Maximum depth of cut A type is 21mm, B type is 20.4mm.
2 The maximum diameter when machining a blind hole with a flat face using a corner radius of 0.8mm for A type and 4mm for B type.
Other than that, find with the below formula.
{(cutting edge diameter DC) (corner radius) 0.3)}2
3 The minimum diameter when machining a blind hole with a flat face using a corner radius of 0.8mm for A type and 4mm for B type.
Other than that, find with the below formula.
{(cutting edge diameter DC) (corner radius) (Width of wiper edge BS) 0.1)}2
*
*
*
Type
Max. Drilling Depth (mm)
(mm)
Type A
Type B
L070
Insert
corner radius
RE
0.8
MILLING
y Max. Drilling Depth
3.2
4.0
5.0
5
4
AXD7000 can be effectively used for

pocket machining without the need
for a prepared hole.
7
9
10
11
12
12
11
7
8
8
8
9
8
11
y CAUTION FOR USE
Procedure for attaching inserts

1) Clean the seat by air blowing or with a brush before installing the insert.
2) Tighten the clamp screw using the accessory wrench while pressing the insert against the seat.
3) Tighten the clamp screw as shown in Figure 1.
4) Coat the clamp screw with anti-seize compound and tighten it to the specified tightening torque.
The tightening torque is shown below.
AXD7000 3.5Nm(2.58ftlb)
AXD4000 1.5Nm(1.11ftlb)
5) The clamp screw is an important part in ensuring safety.
Purchase an official product from Mitsubishi Materials.
When using over the revolution shown in Table 2, replacing the clamp screw simultaneously with
insert replacement is recommended.
Type
AXD4000
1st
2nd
Fig.1
AXD7000
Cutting Edge Diameter DC(mm)
20
25 125
32
40 125
Clamp Screw Number
TS3SBS
TS3SB
TS4SB
TS4SBL
Overall Length L(mm)
6.5
10.5
6) Check that there is no clearance at the insert seat surface.
Installation of arbor type

1) Clean carefully the inside and face of the hole and the arbor face before installing the body to the arbor.
2) Set the body at the arbor and tighten it with the accessory. Refer to the table shown below for the tightening torque.
3) The set bolt supplied with the AXD is a special coolant through compatible nozzle. Be careful not to lose it.
AXD4000
AXD7000
Geometry
Fig.1
Fig.2
Clamp Torque Cutting Edge Diameter Fig

(N m)
DC(mm)
Set Bolt
Fig.3
HFF08043H
11
40
HSC10030H
40
50, 63
Geometry
Fig.1
Set Bolt
Fig.2
Clamp Torque Cutting Edge Diameter Fig

(Nm)
DC(mm)
HSC10030H
40
50, 63
HSC12035H
80
80
HSC12035H
80
80
HSC16040H
150
100
HSC16040H
150
100
MBA20040H
320
120
MBA20040H
320
120
Table 1 Max. Allowable Revolution

25
32
40
50
63
80
100
125
Max. Allowable Revolution (min-1)
49000
48000
41000
35000
30000
27000
23000
20000
32
40
50
63
80
100
125
41000
36000
30000
25000
23000
19000
16000
AXD7000
Max. Allowable Revolution
(min-1)
MILLING
AXD4000
a Even when operating under the maximum allowable spindle speed, if the spindle speed is equal to or higher than the values shown in table 2, it is
recommended that the balance quality (with the arbor or milling chuck) conforms to G6.3 or betterbased on ISO1940. It is also recommended to replace the
clamp screws with new ones when changing inserts. Furthermore,ensure to use machines that are provided with safety measures in case of cutter breakage.
(Note) The balance quality of the holder (without inserts and clamp screws) is G6.3 or better at 10,000min-1.
Table 2 Maximum spindle speed when balancing with the arbor or milling chuck has not been achieved
AXD4000
25
32
40
50
63
80
100
125
12000
9500
7600
6000
4800
3800
3000
2400
32
40
50
63
80
100
125
9500
7600
6000
4800
3800
3000
2400
AXD7000
a When setting the spindle speed, take into consideration the maximum allowable spindle speed of the arbor or milling chuck.
a Use the specified set bolt when using the arbor type with through coolant.
a The inserts have sharp cutting edges and handling them with bare hands may cause injuries.
Always wear safety gloves whenhandling the indexable inserts.

SPARE PARTS
TECHNICAL DATA
P001
Q001
L071
INDEXABLE MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
DAH
DC
Cutter Diameter
DC
L8
L8
DCCB
*1
L8
APMX
WT 3
8.4
5.6
0.3 15 9 29000 1 TS4SL TKY15W
8.5 32
BXD4000-050A04RA
50 50 22
20 11
41 10.4
BXD4000-063A05RA
63 50 22
20 11
50 10.4
6.3 17 0.4 15 6 24000 2 TS4SL TKY15W XDGT1550

6.3 17 0.7 15 5 21000 2 TS4SL TKY15W PDoR-Goo
BXD4000R08005CA
80 50 25.4
26 13
60
9.5
20 1.1 15 3 19000 2 TS4SL TKY15W XDGT1550
BXD4000R10006DA
6 100 63 31.75 32 17
70 12.7
26 2.0 15 3 16000 2 TS4SL TKY15W PDoR-GLoo
BXD4000R12507EA
7 125 63 38.1
40
80 15.9 10
BXD4000-040A03RB
40 50 16
18
8.5 32
BXD4000-050A04RB
50 50 22
20 11
41 10.4
6.3 17 0.4 15 6 24000 2 TS4SL TKY15W
BXD4000-063A05RB
63 50 22
20 11
50 10.4
6.3 17 0.7 15 5 21000 2 TS4SL TKY15W XDGT1550
BXD4000R08005CB
80 50 25.4
26 13
60
9.5
20 1.1 15 3 19000 2 TS4SL TKY15W PDoR-Goo
BXD4000R10006DB
6 100 63 31.75 32 17
70 12.7
26 2.0 15 3 16000 2 TS4SL TKY15W
BXD4000R12507EB
7 125 63 38.1
80 15.9 10
56 2.8 15 2 14000 3 TS4SL TKY15W
40
BD
18
LF
40 50 16
DC
8.4
5.6
(kg) (mm)
Clamp
Wrench
Screw
Insert
56 2.8 15 2 14000 3 TS4SL TKY15W

0.3 15 9 29000 1 TS4SL TKY15W
1 Clamp Torque (N m) : TS4SL=4.0
3 WT : Tool Weight
KWW
DCON
Max.
Allowable
Revolution
(min-1)
*
*
*
L072
Dimensions(mm)
DAH
5.0
&125
CBDP
4.0
Stock
Number of Teeth
Insert Radius
Type
A type
B type
MILLING
3.2
&100
Geometry
z
BXD4000 -040A03RA
RE
0.4
& 80
KAPR :0
GAMP :+11 +15 T :+8 +16
GAMF :+8 +16 I :+11 +15
HFF08043H
HSC10030H
12035H
16040H
MBA20040H
&50, &63
Set Bolt
RMPX 2
&40
set bolts in the right table are supplied

with respective cutter.
Order Number
DCCB
DC
a The
y ARBOR TYPE
DAH
DCCB
DC
APMX
holder produce high wall accuracy.

a Low resistance insert and high rigidity
design for excellent performance.
a With through coolant holes to
ensure smooth chip discharge.
APMX
a Curved cutting edge and high rigidity
BD
DCON
KWW
CBDP
LF
125
APMX
Fig.3
CBDP
BD
DCON
KWW
Type(Fig.)
K
Cast Iron
Fig.2
50
63
80
100
CBDP
M
Stainless Steel
40
BD
DCON
KWW
LF
P
Steel
Fig.1
LF
BXD4000
Roughing
L8
<ALUMINIUM ALLOY TO DIFFICULT-TO-CUT MATERIAL CUTTING>
Finishing
Fig.3
CBDP
LF
APMX
APMX
LF
DAH
DCCB
DC
APMX
DAH
DC
BD
DCON
KWW
125
L8
BD
DCON
KWW
LF
CBDP
L8
50
63
80
100
L8
Fig.2
BD
DCON
KWW
40
CBDP
Fig.1
DCCB
DC

Cutter Diameter
DC
0.4
3.2
4.0
B type
A type
5.0
&125
Max.
Allowable
Revolution
(min-1)
*1
DCCB
L8
APMX
WT 3
(kg) (mm)
8.4 5.6
0.3 15 9 29000 1 TS4SL TKY15W
KWW
BD
DAH
CBDP
DCON
LF
RE
&100
Dimensions(mm)
DC
Order Number
Stock
Number of Teeth
Insert Radius
Type
y ARBOR TYPE
&80
KAPR :0
GAMP :+11 +15 T :+8 +16
GAMF :+8 +16 I :+11 +15
Type(Fig.)
Geometry
HFF08043H
HSC10030H
12035H
16040H
MBA20040H
&40
&50, &63
RMPX 2
For metric arbor
Set Bolt
Clamp
Wrench
Screw
Insert
BXD4000-040A03RA
40 50 16 18
BXD4000-050A04RA
50 50 22 20 11
41 10.4 6.3 17 0.4 15 6 24000 2 TS4SL TKY15W
BXD4000-063A05RA
63 50 22 20 11
BXD4000-080A05RA
80 50 27 23 13
50 10.4 6.3 17 0.7 15 5 21000 2 TS4SL TKY15W XDGT1550

60 12.4 7
BXD4000-100A06RA
6 100 63 32 26 17
70 14.4 8
26 2.0 15 3 16000 2 TS4SL TKY15W
BXD4000-125B07RA
7 125 63 40 40
80 16.4 9
56 2.8 15 2 14000 3 TS4SL TKY15W
BXD4000-040A03RB
40 50 16 18
8.5 32
BXD4000-050A04RB
50 50 22 20 11
41 10.4 6.3 17 0.4 15 6 24000 2 TS4SL TKY15W
BXD4000-063A05RB
63 50 22 20 11
BXD4000-080A05RB
80 50 27 23 13
50 10.4 6.3 17 0.7 15 5 21000 2 TS4SL TKY15W XDGT1550

60 12.4 7
BXD4000-100A06RB
6 100 63 32 26 17
70 14.4 8
26 2.0 15 3 16000 2 TS4SL TKY15W
BXD4000-125B07RB
7 125 63 40 40
80 16.4 9
56 2.8 15 2 14000 3 TS4SL TKY15W
8.5 32
8.4 5.6
0.3 15 9 29000 1 TS4SL TKY15W
3 WT : Tool Weight
MILLING
*
*
y CAUTION FOR USE

a Only use the inserts and parts provided by Mitsubishi Materials with this tool. Use of the correct insert clamp screws is especially important
to ensure overall tool safety. Do not use damaged or worn clamp screws.
a The maximum allowable spindle speeds are shown in Table 1. Ensure that the cutter operates under the maximum allowable spindle speed.
The maximum allowable spindle speeds for safety purposes are determined in accordance with ISO15641 (Milling Cutters for high speed
machiningSafety requirements).
Table 1 Max. Allowable Revolution

20
15000
25
28
32
35
40
50
63
80
100
125
38000
35000
33000
31000
29000
24000
21000
19000
16000
14000
&20mm with one tooth balancing is necessary to adjust sensitively.

a Even when operating under the maximum allowable spindle speed, if the spindle speed is equal to or higher than the values shown in table 2, it is
recommended that the balance quality (with the arbor or milling chuck) conforms to G40 or betterbased on ISO1940. It is also recommended to replace the
clamp screws with new ones when changing inserts. Furthermore,ensure to use machines that are provided with safety measures in case of cutter breakage.
Table 2 Maximum spindle speed when balancing with the arbor or milling chuck has not been achieved
Max. Allowable Revolution
(min-1)
20
25
28
32
35
40
50
63
80
100
125
15000
12000
10800
9500
8700
7600
6000
4800
3800
3000
2400
a When setting the spindle speed, take into consideration the maximum allowable spindle speed of the arbor or milling chuck.
a Use the specified set bolt when using the arbor type with through coolant.
a The inserts have sharp cutting edges and handling them with bare hands may cause injuries.
Always wear safety gloves whenhandling the indexable inserts.
SPARE PARTS
TECHNICAL DATA
P001
Q001
L073
INDEXABLE MILLING
DC
DCON
Fig.1 Straight Shank
APMX
LH
LF
DC
DCON
Fig.2 Offset Shank
APMX
LH
LF
4.0
5.0
Extra
Long
MILLING
Long
Type B
Standard
Extra
Long
Long
3.2
*1
DC
BXD4000R201SA20SA
20
BXD4000R252SA25SA
25
15
125
50
25
20
38000 1 TS4SL TKY15W
BXD4000R282SA25SA
28
15
125
50
25
17
BXD4000R322SA32SA
32
15
150
50
32
13
BXD4000R352SA32SA
35
15
150
50
32
11
BXD4000R403SA32SA
40
15
170
80
32
31000 2 TS4SL TKY15W XDGT1550

29000 2 TS4SL TKY15W PDpR-Gpp
BXD4000R403SA42SA
40
15
170
80
42
BXD4000R252SA25LA
25
15
170
80
25
20

p
pp
38000 1 TS4SL TKY15W PD R-GL
BXD4000R322SA32LA
32
15
200
80
32
13
BXD4000R282SA25ELA
28
15
220
50
25
17
BXD4000R352SA32ELA
35
15
250
50
32
11
BXD4000R403SA32ELA
40
15
250
65
32
Order Number
Max.
RMPX Allowable
Revolution
Dimensions(mm)
Type(Fig.)
Stock
Number of Teeth
0.4
Type A
Standard
RE
Shank Type
Type
Insert
Radius
y SHANK TYPE
Clamp
Screw
APMX
LF
LH
DCON
15
110
35
20
28
(min-1)
Wrench
BXD4000R201SA20SB
20
15
110
35
20
28
BXD4000R252SA25SB
25
15
125
50
25
20
BXD4000R282SA25SB
28
15
125
50
25
17
BXD4000R322SA32SB
32
15
150
50
32
13
BXD4000R352SA32SB
35
15
150
50
32
11
BXD4000R403SA32SB
40
15
170
80
32
BXD4000R403SA42SB
40
15
170
80
42
BXD4000R252SA25LB
25
15
170
80
25
20
BXD4000R322SA32LB
32
15
200
80
32
13
BXD4000R282SA25ELB
28
15
220
50
25
17
BXD4000R352SA32ELB
35
15
250
50
32
11
BXD4000R403SA32ELB
40
15
250
65
32
Insert

29000 1 TS4SL TKY15W PDpR-Gpp
(Note 1) The maximum allowed revolutions are set to ensure tool and insert stability.
(Note 2) When using the tool at high revolutions, ensure that the tool and arbor are correctly balanced.
*
*
y HOLDER AND INSERT CORNER RADIUS COMBINATION

A Holder
Holder
B Holder
BXD4000RpppppppA
R 0.4
Insert
Corner
Radius
(RE)
R 0.8
R 1.2
R 1.6
BXD4000RpppppppB
R 2.0
R 3.0
R 3.2
L074
R 5.0
XDGT.....-G04 XDGT.....-G08
XDGT.....-G12 XDGT.....-G16 XDGT.....-G20 XDGT.....-G30 XDGT.....-G32 XDGT.....-G40 XDGT.....-G50
XDGT.....-GL04 XDGT.....-GL08
(Note 1) Please only use the holder and insert corner radius combinations shown above.
(Note 2) XDGT....-GL08 and -G12 inserts are compatible only with the BXD4000RpppppppA type holder.
a
R 4.0
INSERTS
Steel

: Stable Cutting
: General Cutting
Stainless Steel
: Unstable Cutting
Cast Iron
Non-ferrous Metal
Honing :
E : Round F : Sharp

Hardened Steel
Order Number
Low Resistance XDGT1550PDFR-GL04 G F

Type
XDGT1550PDFR-GL08 G F
Dimensions(mm)
Geometry
INSL
BS
RE
16
16
5
5
1.5
1.1
0.4
0.8
TF15
Shape
Class
Honing
VP15TF
LC15TF
Stock
Coated Carbide
a
a
22
22
RE
BS
Work
Material
P
M
K
N
S
H
20
30
IN
S
22
22
16
16
5
5
1.5
1.1
0.4
0.8
G F
22
16
0.7
1.2
G F
22
16
0.4
1.6
G F
21.7 16
0.2
2.0
G F
20
16
0.6
3.0
G F
20
16
0.4
3.2
G F
G F
19
18
16
16
5
5
0.5
0.4
4.0
5.0
G E
G E
a
a
22
22
16
16
5
5
1.5
1.1
0.4
0.8
G E
22
16
0.7
1.2
G E
22
16
0.4
1.6
G E
21.7 16
0.2
2.0
G E
20
16
0.6
3.0
G E
20
16
0.4
3.2
G E
G E
19
18
16
16
5
5
0.5
0.4
4.0
5.0
RE
20
S
30
IN
S
RE
20
S
30
IN
S

Work Material
Cutting Speed
Feed per Tooth
VP15TF
180 (150 200)
0.15 (0.1 0.2)
< 280HB
VP15TF
150 (120 200)
0.15 (0.1 0.2)
280 350HB
VP15TF
140 (120 160)
0.15 (0.1 0.2)
Hardness
Grade
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
(m/min)
(mm/t.)
Stainless Steel
< 270HB
VP15TF
140 (120 160)
0.2 (0.1 0.3)
Aluminium Alloy
LC15TF
TF15
1000 (200 3000)
0.3 (0.1 0.5)
Ti Alloy
VP15TF
40 (30 60)
0.1 (0.1 0.3)
Heat Resistance Alloy

(Inconel etc.)
VP15TF
30 (20 40)
0.15 (0.1 0.2)
Hardened Steel
40 60HRC
VP15TF
70 (50 100)
0.1 (0.0 5 0.15)
MILLING
BS
G F
G F
BS
XDGT1550PDFR-G04
XDGT1550PDFR-G08
XDGT1550PDFR-G12
XDGT1550PDFR-G16
XDGT1550PDFR-G20
XDGT1550PDFR-G30
XDGT1550PDFR-G32
XDGT1550PDFR-G40
XDGT1550PDFR-G50
XDGT1550PDER-G04
XDGT1550PDER-G08
XDGT1550PDER-G12
XDGT1550PDER-G16
XDGT1550PDER-G20
XDGT1550PDER-G30
XDGT1550PDER-G32
XDGT1550PDER-G40
XDGT1550PDER-G50
a Figures above are a guide lines for optimum general use. They may vary depending on machine rigidity, work clamping and length of tool overhang.
a When using & 20 shank type, set the table feed at under 0.05mm/t. and maintain observation during cutting.
a Please adjust the table feed when using long- and extra-long-shank types.
a Please adjust the table feed when ramp machining (Recommended feed:0.05 mm/t. under).
SPARE PARTS
TECHNICAL DATA
P001
Q001
L075
INDEXABLE MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
Roughing
AQX
APMX
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
H
Hardened Steel
DCON
DC
A3
90
LH
3.
LF
Number of
Teeth : 4
a The center bottom cutting edge enables drilling
without previously formed hole.
Long
MILLING
Standard
AQXR164SA16S
AQXR164SN16S
AQXR174SA16S
AQXR174SN16S
AQXR204SA20S
AQXR204SN20S
AQXR214SA20S
AQXR214SN20S
AQXR254SA25S
AQXR254SN25S
AQXR264SA25S
AQXR264SN25S
AQXR324SA32S
AQXR324SN32S
AQXR334SA32S
AQXR334SN32S
AQXR354SA32S
AQXR354SN32S
AQXR404SA32S
AQXR404SN32S
AQXR504SA42S
AQXR504SN42S
AQXR164SA16L
AQXR164SN16L
AQXR174SA16L
AQXR174SN16L
AQXR204SA20L
AQXR204SN20L
AQXR214SA20L
AQXR214SN20L
AQXR254SA25L
AQXR254SN25L
AQXR264SA25L
AQXR264SN25L
AQXR324SA32L
AQXR324SN32L
AQXR334SA32L
AQXR334SN32L
AQXR354SA32L
AQXR354SN32L
AQXR404SA32L
AQXR404SN32L
AQXR504SA42L
AQXR504SN42L
R
a
Stock
Order Number
Coolant Hole
Type
y STANDARD EDGE TYPE

Dimensions (mm)
DC
LF
DCON
LH
16
16
17
17
20
20
21
21
25
25
26
26
32
32
33
33
35
35
40
40
50
50
16
16
17
17
20
20
21
21
25
25
26
26
32
32
33
33
35
35
40
40
50
50
120
120
120
120
130
130
130
130
140
140
140
140
150
150
150
150
150
150
160
160
170
170
175
175
175
175
185
185
185
185
220
220
220
220
230
230
230
230
230
230
240
240
250
250
16
16
16
16
20
20
20
20
25
25
25
25
32
32
32
32
32
32
32
32
42
42
16
16
16
16
20
20
20
20
25
25
25
25
32
32
32
32
32
32
32
32
42
42
30
30
30
30
35
35
35
35
40
40
40
40
50
50
50
50
50
50
60
60
70
70
50
50
30
30
60
60
35
35
75
75
40
40
90
90
50
50
50
50
60
60
70
70
A3 *
4.5
4.5
4.5
4.5
6
6
6
6
7.5
7.5
7.5
7.5
9.5
9.5
9.5
9.5
11
11
12
12
15
15
4.5
4.5
4.5
4.5
6
6
6
6
7.5
7.5
7.5
7.5
9.5
9.5
9.5
9.5
11
11
12
12
15
15
3 z
APMX* Clamp Screw

2
17.6
17.6
17.6
17.6
22
22
22
22
27.5
27.5
27.5
27.5
35.2
35.2
35.2
35.2
40
40
44
44
55
55
17.6
17.6
17.6
17.6
22
22
22
22
27.5
27.5
27.5
27.5
35.2
35.2
35.2
35.2
40
40
44
44
55
55
TS2A
TS2A
TS2A
TS2A
TS25
TS25
TS25
TS25
TS33
TS33
TS33
TS33
TS407
TS407
TS407
TS407
TS407
TS407
TS55
TS55
TS6S
TS6S
TS2A
TS2A
TS2A
TS2A
TS25
TS25
TS25
TS25
TS33
TS33
TS33
TS33
TS407
TS407
TS407
TS407
TS407
TS407
TS55
TS55
TS6S
TS6S
Wrench
zTKY06F
zTKY06F
zTKY06F
zTKY06F
zTKY08F
zTKY08F
zTKY08F
zTKY08F
xTKY08D
xTKY08D
xTKY08D
xTKY08D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY25D
xTKY25D
cTKY30T
cTKY30T
zTKY06F
zTKY06F
zTKY06F
zTKY06F
zTKY08F
zTKY08F
zTKY08F
zTKY08F
xTKY08D
xTKY08D
xTKY08D
xTKY08D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY25D
xTKY25D
cTKY30T
cTKY30T
Insert
QOG/MT0830R-G1/M2
QOG/MT1035R-G1/M2
QOG/MT1342R-G1/M2
QOG/MT1651R-G1/M2
QOG/MT1856R-G1/M2
QOG/MT2062R-G1/M2
QOG/MT2576R-G1/M2
QOG/MT0830R-G1/M2
QOG/MT1035R-G1/M2
QOG/MT1342R-G1/M2
QOG/MT1651R-G1/M2
QOG/MT1856R-G1/M2
QOG/MT2062R-G1/M2
QOG/MT2576R-G1/M2
Dimension A3 represents the depth of cut when the cutting edge consists of 2 inserts.
*31 Clamp
*2 APMX : Maximum depth of cut.
Torque (N m) : TS2A=0.6, TS25=1.0, TS33=1.0, TS407=3.5, TS55=7.5, TS6S=10.0
* a : Inventory maintained in Japan.
L076
DC
DCON
APMX
90
A3
LH
Number of
Teeth : 2
3.
LF
Long
AQXR162SA16S
AQXR162SN16S
AQXR172SA16S
AQXR172SN16S
AQXR202SA20S
AQXR202SN20S
AQXR212SA20S
AQXR212SN20S
AQXR252SA25S
AQXR252SN25S
AQXR262SA25S
AQXR262SN25S
AQXR322SA32S
AQXR322SN32S
AQXR332SA32S
AQXR332SN32S
AQXR352SA32S
AQXR352SN32S
AQXR402SA32S
AQXR402SN32S
AQXR502SA42S
AQXR502SN42S
AQXR162SA16L
AQXR162SN16L
AQXR172SA16L
AQXR172SN16L
AQXR202SA20L
AQXR202SN20L
AQXR212SA20L
AQXR212SN20L
AQXR252SA25L
AQXR252SN25L
AQXR262SA25L
AQXR262SN25L
AQXR322SA32L
AQXR322SN32L
AQXR332SA32L
AQXR332SN32L
AQXR352SA32L
AQXR352SN32L
AQXR402SA32L
AQXR402SN32L
AQXR502SA42L
AQXR502SN42L
Stock
R
Coolant Hole
Order Number
Dimensions (mm)
DC
LF
DCON
LH
16
16
17
17
20
20
21
21
25
25
26
26
32
32
33
33
35
35
40
40
50
50
16
16
17
17
20
20
21
21
25
25
26
26
32
32
33
33
35
35
40
40
50
50
120
120
120
120
130
130
130
130
140
140
140
140
150
150
150
150
150
150
160
160
170
170
175
175
175
175
185
185
185
185
220
220
220
220
230
230
230
230
230
230
240
240
250
250
16
16
16
16
20
20
20
20
25
25
25
25
32
32
32
32
32
32
32
32
42
42
16
16
16
16
20
20
20
20
25
25
25
25
32
32
32
32
32
32
32
32
42
42
30
30
30
30
35
35
35
35
40
40
40
40
50
50
50
50
50
50
60
60
70
70
50
50
30
30
60
60
35
35
75
75
40
40
90
90
50
50
50
50
60
60
70
70
A3 *
4.5
4.5
4.5
4.5
6
6
6
6
7.5
7.5
7.5
7.5
9.5
9.5
9.5
9.5
11
11
12
12
15
15
4.5
4.5
4.5
4.5
6
6
6
6
7.5
7.5
7.5
7.5
9.5
9.5
9.5
9.5
11
11
12
12
15
15
3 z
APMX* Clamp Screw

2
7.4
7.4
7.4
7.4
9.2
9.2
9.2
9.2
11.5
11.5
11.5
11.5
14.5
14.5
14.5
14.5
16
16
18
18
23
23
7.4
7.4
7.4
7.4
9.2
9.2
9.2
9.2
11.5
11.5
11.5
11.5
14.5
14.5
14.5
14.5
16
16
18
18
23
23
TS2A
TS2A
TS2A
TS2A
TS25
TS25
TS25
TS25
TS33
TS33
TS33
TS33
TS407
TS407
TS407
TS407
TS407
TS407
TS55
TS55
TS6S
TS6S
TS2A
TS2A
TS2A
TS2A
TS25
TS25
TS25
TS25
TS33
TS33
TS33
TS33
TS407
TS407
TS407
TS407
TS407
TS407
TS55
TS55
TS6S
TS6S
Wrench
zTKY06F
zTKY06F
zTKY06F
zTKY06F
zTKY08F
zTKY08F
zTKY08F
zTKY08F
xTKY08D
xTKY08D
xTKY08D
xTKY08D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY25D
xTKY25D
cTKY30T
cTKY30T
zTKY06F
zTKY06F
zTKY06F
zTKY06F
zTKY08F
zTKY08F
zTKY08F
zTKY08F
xTKY08D
xTKY08D
xTKY08D
xTKY08D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY15D
xTKY25D
xTKY25D
cTKY30T
cTKY30T
Insert
QOG/MT0830R-G1/M2
QOG/MT1035R-G1/M2
QOG/MT1342R-G1/M2
QOG/MT1651R-G1/M2
QOG/MT1856R-G1/M2
QOG/MT2062R-G1/M2
QOG/MT2576R-G1/M2
QOG/MT0830R-G1/M2
QOG/MT1035R-G1/M2
MILLING
Standard
Type
y SHORT EDGE TYPE
QOG/MT1342R-G1/M2
QOG/MT1651R-G1/M2
QOG/MT1856R-G1/M2
QOG/MT2062R-G1/M2
QOG/MT2576R-G1/M2
Dimension A3 represents the depth of cut when the cutting edge consists of 2 inserts.
*12 APMX
Maximum depth of cut.
*3 Clamp :Torque
(N m) : TS2A=0.6, TS25=1.0, TS33=1.0, TS407=3.5, TS55=7.5, TS6S=10.0
*
SPARE PARTS
TECHNICAL DATA
P001
Q001
L077
INDEXABLE MILLING
A
DC
DCON
CRKS
90
3.5
A3
BD
APMX
A
L11
LF
OAL
H
A-A section
y SCREW-IN TYPE
DC DCON BD OAL LF
AQXR162M08A30
16
8.5 14.7 48
30
10 M8
4.5
AQXR172M08A30
17
8.5 14.5 48
30
10 M8
AQXR202M10A30
20 10.5 18.6 49
30
AQXR212M10A30
21 10.5 18.5 49
30
AQXR252M12A35
25 12.5 23.5 57
AQXR262M12A35
AQXR322M16A40
AQXR332M16A40
Order Number
Stock
R
Coolant Hole

x
WT
(kg)
L11
*
CRKS A3* APMX
1
Clamp Screw
Wrench
7.4 0.1
TS2A
zTKY06F
4.5
7.4 0.1
TS2A
zTKY06F
14 M10
9.2 0.2
TS25
zTKY08F
14 M10
9.2 0.2
TS25
zTKY08F
35
19 M12
7.5 11.5 0.2
TS33
xTKY08D
26 12.5 23.5 57
35
19 M12
7.5 11.5 0.2
TS33
xTKY08D
32 17
28.5 63
40
24 M16
9.5 14.5 0.3
TS407
xTKY15D
33 17
28.5 63
40
24 M16
9.5 14.5 0.3
TS407
xTKY15D
AQXR352M16A40
35 17
28.5 63
40
24 M16 11
16
0.3
TS407
xTKY15D QOpT1856R-pp
AQXR402M16A45
40 17
28.5 68
45
24 M16 12
18
0.3
TS55
xTKY25D QOpT2062R-pp

1 Dimension A3 represents the depth of cut when the cutting edge consists of 2 inserts.
2 APMX : Maximum depth of cut.
3 Clamp Torque (N m) : TS2A=0.6, TS25=1.0, TS33=1.0, TS407=3.5, TS55=7.5
4 WT : Tool Weight
MILLING
*
*
*
*
L078
*4
Dimensions(mm)
3 z
Insert
QOpT0830R-pp
QOpT1035R-pp
QOpT1342R-pp
QOpT1651R-pp
INSERTS
Steel

: Stable Cutting
: General Cutting
Stainless Steel
Non-ferrous Metal
Honing :
E : Round F : Sharp
Endmill
Dia.
Class
Honing
VP15TF
VP30RT
Order Number
Carbide
Dimensions(mm)
L
W1
8.4
QOMT1035R-M2
a a
QOMT1342R-M2
& 25,26 M E
a a
QOMT1651R-M2
& 32,33 M E
a a
16.5
QOMT1856R-M2
& 35
M E
a a
18
QOMT2062R-M2
& 40
M E
a a
QOMT2576R-M2
& 50
M E
a a
QOGT0830R-G1
& 16,17 G F
8.4
5.5
0.4
QOGT1035R-G1
& 20,21 G F
10.6
3.5
0.4
QOGT1342R-G1
& 25,26
13.1
8.7
4.2
0.4
QOGT1651R-G1
& 32,33
16.5
11
5.1
0.4
QOGT1856R-G1
& 35
18
12
5.6
0.4
QOGT2062R-G1
& 40
20.4
13.6
6.2
0.4
QOGT2576R-G1
& 50
25.8
17.2
7.6
0.4
5.5
0.8
10.6
3.5
0.8
13.1
8.7
4.2
0.8
11
5.1
0.8
12
5.6
0.8
20.4
13.6
6.2
0.8
25.8
17.2
7.6
0.8
RE
RE
a a
& 20,21 M E
& 16,17 M E
E
R
QOMT0830R-M2
*a
*a
G F* a
G F* a
G F* a
G F* a
G F* a
Geometry
RE
W1
Hardened Steel
W1
Coated
Shape
: Unstable Cutting
Cast Iron
HTi10
Work
Material
P
M
K
N
S
H
* VP15TF insert honing is "E" type.

CUTTING MODE
Pocketing
Ramping
Slotting
Copying
MILLING
Plunging
Drilling
Shoulder
Helical
SCREW-IN ARBORS
SPARE PARTS
TECHNICAL DATA
L145
P001
Q001
L079
INDEXABLE MILLING
aUp to A3 depth of cut, the two lower cutting edges maintain
contact with the workpiece.
6DC
4.5DC
BT50
3DC
BT40
HSK63
1.5DC
A3
DC=Cutting
Edge
0
Diameter
50%
100%
Feed Rate
APMX
contact with the workpiece becomes single bladed. Please pay special
attention to the relationship between depth of cut and feed in this area.
aThe insert in contact with the top edge of the workpiece
tends to suffer from damege. At large depths of cut, applying
depth of cut (t), where there are 2 inserts in contact is
recommended to reduce wear and damage to the inserts.
Diameter Recommended depth of cut t (mm)
&16,17
12 14
&20,21
14 17
&25,26
17 22
&32,33
22 28
&35
25 32
&40
28 35
Figures for A3 and APMX are shown in the
35 45
standard holder tables on the previous pages. &50
Overhang
aBeyond the range of A3, there is an area where the cutting edge
aChatter, vibration and other operational problems
tend to occur with a long tool overhang and/or low

machine rigidity, resulting in unstable machining.
aPlease reduce the feed accordingly in these
conditions, using the chart above as a guideline.
y FOR SHOULDER MILLING

Work Material
Hardness
Grade
Cutting Speed
(m/min)
< 180HB
VP15TF
180
(150 220)
P
Mild Steel
Carbon Steel
Alloy Steel
180 350HB
M
Stainless Steel
K
Cast Iron
< 270HB
Tensile Strength
< 450MPa
N
Aluminium Alloy
VP15TF
VP30RT
(VP15TF)
VP15TF
HTi10
(G1 Breaker)
H
Hardened Steel
40 55HRC
VP15TF
160
(120 200)
150
(120 180)
180
(150 220)
500
(200 800)
80
(50 120)
&16, &17
&20, &21
Depth of Cut Width of Cut Feed Depth of Cut Width of Cut Feed
(mm)
(mm) (mm/rev)
(mm)
(mm) (mm/rev)
4.5
0.25
10
0.30
4.5 12
0.16
6 14
0.25
12 17
0.10
14 22
0.18
4.5
0.20
10
0.25
4.5 12
0.14
6 14
0.20
12 17
0.08
14 22
0.16
4.5
0.20
10
0.25
4.5 12
0.14
6 14
0.20
12 17
0.08
14 22
0.16
4.5
0.25
10
0.30
4.5 12
0.16
6 14
0.25
12 17
0.10
14 22
0.18
11
0.30
14
0.35
4.5 12
0.21
6 14
10
0.30
12 17
0.15
14 22
0.23
4.5
0.16
0.20
4.5 12
0.10
6 14
0.16
12 17
0.06
14 22
0.12
4.5
MILLING
(Note 1) Please pay special attention to the depth of cut when using the short edge type.
(Note 2) When using the G1 breaker (VP15TF), reduce the feed rate by at least 20%.
y FOR SLOT MILLING

Work Material
Hardness
Grade
Cutting Speed
(m/min)
< 180HB
VP15TF
180
(150 220)
P
Mild Steel
Carbon Steel
Alloy Steel
180 350HB
Stainless Steel
< 270HB
K
Cast Iron
Tensile Strength
< 450MPa
N
Aluminium Alloy
Hardened Steel
40 55HRC
VP15TF
VP30RT
(VP15TF)
VP15TF
&16, &17
Depth of Cut
(mm)
Depth of Cut
(mm)
Feed
(mm/rev)
4.5
0.16
0.18
4.5 12
0.10
6 14
0.14
12 17
0.07
14 22
4.5
0.14
0.10
0.16
160
(120 200)
4.5 12
0.09
6 14
0.12
12 17
0.05
14 22
0.10
150
(120 180)
4.5
0.14
0.16
4.5 12
0.09
6 14
0.12
12 17
0.05
14 22
0.10
4.5
0.16
0.18
4.5 12
0.10
6 14
0.14
12 17
0.07
14 22
0.10
4.5
0.18
0.20
4.5 12
0.12
6 14
0.16
12 17
0.09
14 22
4.5
0.10
0.12
4.5 12
0.07
6 14
0.10
180
(150 220)
HTi10
(G1 Breaker)
500
(200 800)
VP15TF
80
(50 120)
(Note 1) Please pay special attention to the depth of cut when using the short edge type.
(Note 2) When using the G1 breaker (VP15TF), reduce the feed rate by at least 20%.
L080
&20, &21
Feed
(mm/rev)
0.12
& 25, & 26
&32, &33
&35
&40
&50
7.5
7.5 17
17 27
12.5
0.35
9.5
16
0.40
11
0.28
9.5 22
11
0.32
11 25
17.5
0.45
12
20
0.50
15
25
0.60
12
0.35
12 28
13
0.40
15 35
16
0.50
6.5
0.28
28 44
0.30
35 55
10
0.35
17.5
0.37
12
20
0.40
15
25
0.50
0.20
22 35
0.25
25 40
12.5
0.30
9.5
16
0.35
11
7.5 17
0.25
9.5 22
10
0.28
11 25
11
0.30
12 28
12
0.32
15 35
14
0.40
17 27
0.18
22 35
0.20
25 40
5.5
0.22
28 44
0.25
35 55
0.30
7.5
7.5
7.5 17
17 27
7.5
7.5 17
17 27
12.5
0.30
9.5
16
0.35
11
17.5
0.37
12
20
0.40
15
25
0.50
0.25
9.5 22
10
0.28
11 25
12
0.30
12 28
12
0.32
15 35
14
0.40
6.5
0.22
28 44
0.25
35 55
0.30
17.5
0.45
12
20
0.50
15
25
0.60
12
0.35
12 28
13
0.40
15 35
16
0.50
0.18
22 35
0.20
25 40
12.5
0.35
9.5
16
0.40
11
0.28
9.5 22
11
0.32
11 25
0.20
22 35
0.25
25 40
6.5
0.28
28 44
0.30
35 55
10
0.35
17.5
0.40
9.5
23
0.45
11
24.5
0.50
12
28
0.55
15
35
0.65
7.5 17
12.5
0.33
9.5 22
16
0.37
11 25
17.5
0.40
12 28
20
0.45
15 35
25
0.55
17 27
7.5
0.25
22 35
10
0.30
25 40
10.5
0.32
28 44
12
0.35
35 55
15
0.40
0.22
9.5
0.25
11
0.28
12
10
0.30
15
14
0.35
7.5
7.5
7.5 17
0.18
9.5 22
0.20
11 25
5.5
0.22
12 28
0.24
15 35
0.30
17 27
0.14
22 35
0.16
25 40
0.17
28 44
0.18
35 55
0.22
& 25, & 26
Depth of Cut
(mm)
&32, &33
Feed
(mm/rev)
Depth of Cut
(mm)
&35
Feed
(mm/rev)
Depth of Cut
(mm)
&40
Feed
(mm/rev)
Depth of Cut
(mm)
&50
Feed
(mm/rev)
Depth of Cut
(mm)
Feed
(mm/rev)
7.5
0.20
9.5
0.25
11
0.27
12
0.30
15
0.35
7.5 17
0.16
9.5 22
0.20
11 25
0.22
12 28
0.25
15 35
0.30
17 27
0.12
22 35
0.14
25 40
0.16
28 44
0.18
35 55
0.22
7.5
0.18
9.5
0.20
11
0.22
12
0.25
15
0.30
7.5 17
0.14
9.5 22
0.16
11 25
0.18
12 28
0.20
15 35
0.25
17 27
0.10
22 35
0.12
25 40
0.13
28 44
0.14
35 55
0.16
7.5
0.18
9.5
0.20
11
0.22
12
0.25
15
0.30
7.5 17
0.14
9.5 22
0.16
11 25
0.18
12 28
0.20
15 35
0.25
17 27
0.10
22 35
0.12
25 40
0.13
28 44
0.14
35 55
0.16
7.5
0.20
9.5
0.25
11
0.27
12
0.30
15
0.35
7.5 17
0.16
9.5 22
0.20
11 25
0.22
12 28
0.25
15 35
0.30
17 27
0.12
22 35
0.14
25 40
0.16
28 44
0.18
35 55
0.22
7.5
0.22
9.5
0.27
11
0.30
12
0.32
15
0.37
7.5 17
0.18
9.5 22
0.22
11 25
0.25
12 28
0.27
15 35
0.32
17 27
0.14
22 35
0.16
25 40
0.18
28 44
0.20
35 55
0.25
7.5
0.14
9.5
0.16
11
0.17
12
0.18
15
0.22
7.5 17
0.12
9.5 22
0.12
11 25
0.13
12 28
0.14
15 35
0.16
TECHNICAL DATA
Q001
MILLING
Depth of Cut Width of Cut Feed Depth of Cut Width of Cut Feed Depth of Cut Width of Cut Feed Depth of Cut Width of Cut Feed Depth of Cut Width of Cut Feed
(mm)
(mm) (mm/rev)
(mm)
(mm) (mm/rev)
(mm)
(mm) (mm/rev)
(mm)
(mm) (mm/rev)
(mm)
(mm) (mm/rev)
L081
INDEXABLE MILLING
y FOR HELICAL CUTTING
dc
a How to derive a locus of

a Depth of cut for each pass.
DC
Locus of the center

of the tool
the center of the tool.
DH
Desired hole
diameter
- Cutting
DCedge
diameter
P = ) dc tan %
(Note) %< 3
a Min. machined hole diameter for helical cutting : 1.2DC
Max. machined hole diameter for helical cutting : 1.8DC
dc
DH
a For efficient chip discharge, always apply air blow.

%
a When using a G1 breaker insert (VP15TF), please reduce the feed rate by 20%.
) dc
Work Material
Grade
Cutting
Speed
(m/min)
< 180HB
VP15TF
180
(150 220)
P
Mild Steel

Alloy Steel
Stainless
Steel
Tensile
Strength
< 450MPa
Cast Iron
VP15TF
VP15TF
Aluminium
Alloy
Hardened
Steel
40 55HRC
160
(120 200)
180
(150 220)
HTi10
500
(G1 Breaker) (200 800)
VP15TF
80
(50 120)
&20, &21
&25, &26
Machining Max. Depth Feed DOC/pass Machining Max. Depth Feed DOC/pass Machining Max. Depth Feed DOC/pass
Diameter of Cut
Diameter of Cut
Diameter of Cut
(mm) (mm) (mm/rev) (mm/pass) (mm) (mm) (mm/rev) (mm/pass) (mm) (mm) (mm/rev) (mm/pass)
VP30RT
150
(VP15TF) (120 180)
< 270HB
&16, &17
Hardness
20
0.16
0.44
24
10
0.18
0.44
30
12.5
0.20
0.55
25
12
0.14
0.99
30
15
0.16
1.10
38
19
0.18
1.43
29
16
0.12
1.43
36
20
0.14
1.76
45
25
0.16
2.20
20
0.14
0.33
24
10
0.16
0.33
30
12.5
0.18
0.41
25
12
0.12
0.74
30
15
0.14
0.82
38
19
0.16
1.07
29
16
0.10
1.07
36
20
0.12
1.32
45
25
0.14
1.65
20
0.14
0.22
24
0.16
0.22
30
0.18
0.27
25
0.12
0.49
30
0.14
0.55
38
0.16
0.71
29
0.10
0.71
36
10
0.12
0.88
45
12.5
0.14
1.10
20
10
0.16
0.55
24
14
0.18
0.55
30
18
0.20
0.69
25
13
0.14
1.23
30
17
0.16
1.37
38
21
0.18
1.78
29
16
0.12
1.78
36
20
0.14
2.19
45
25
0.16
2.74
20
10
0.18
0.44
24
14
0.20
0.44
30
18
0.22
0.55
25
13
0.16
0.99
30
17
0.18
1.10
38
21
0.20
1.43
29
16
0.14
1.43
36
20
0.16
1.76
45
25
0.18
2.20
20
0.10
0.22
24
0.12
0.22
30
0.14
0.27
25
0.08
0.49
30
0.10
0.55
38
0.12
0.71
29
0.06
0.71
36
10
0.08
0.88
45
12.5
0.10
1.10
y FOR DRILLING AND PLUNGING

a Drilling
MILLING
DC
Work Material
Mild Steel
less than 0.5DC.

a Use step feed when drilling (0.25
0.5mm) to ensure that the chips are
effectively broken.
a Use internal or external cooling to
ensure that the chips disposal is
sufficiently achieved.
a The chips generated can dispel in any
direction, so ensure that adequate
safety precautions are taken.
Hardness
Grade
Cutting
Speed
(m/min)
< 180HB
VP15TF
Carbon Steel, Alloy Steel 180 350HB
a Plunging
a The recommended drilling depth is
Stainless Steel
< 270HB
Cast Iron
Tensile Strength
< 450MPa
Aluminium Alloy
Hardened Steel
L082
same as the feed for drilling.
Depth of Cut in the

Radius Direction
a No step feed necessary.

a Please refer to the following
table for the depth of cut at

plunging operations.
Depth of Cut in the

Radius Direction
Pick Feed
Pick Feed
&16, &17
&20, &21
< 0.4DC
< 0.5DC
&25, &26
Feed
(mm/rev)
Step
(mm)
Feed
(mm/rev)
Step
(mm)
180
(150 220)
0.035
0.2
0.045
0.3
0.05
0.3
VP15TF
160
(120 200)
0.03
0.2
0.04
0.3
0.045
0.3
VP30RT
(VP15TF)
150
(120 180)
0.03
0.15
0.04
0.25
0.045
0.25
0.04
0.4
0.05
0.5
0.06
0.5
0.04
0.2
0.05
0.3
0.06
0.3
0.02
0.15
0.03
0.25
0.035
0.25
180
VP15TF
(150 220)
HTi10
500
(G1 Breaker) (200 800)

80
VP15TF
40 55HRC
(50 120)
(Note) Helical grooving is strongly recommended for machining of tempered steel.

When using the G1 breaker (VP15TF), reduce the feed rate by at least 20%.
a The feed for plunging is the
Feed
(mm/rev)
Step
(mm)
& 32, & 33
&35
&40
&50
Machining Max. Depth Feed DOC/pass Machining Max. Depth Feed DOC/pass Machining Max. Depth Feed DOC/pass Machining Max. Depth Feed DOC/pass
Diameter
of Cut
Diameter
of Cut
Diameter
of Cut
Diameter
of Cut
(mm)
(mm) (mm/rev) (mm/pass) (mm)
(mm) (mm/rev) (mm/pass)
38
16
0.25
0.66
42
18
0.28
0.77
48
20
0.30
0.88
60
25
0.35
1.10
48
24
0.22
1.76
53
27
0.24
1.97
60
30
0.26
2.19
75
38
0.30
2.74
58
32
0.20
2.85
63
35
0.21
3.07
72
40
0.22
3.51
90
50
0.26
4.39
38
16
0.20
0.49
42
18
0.22
0.58
48
20
0.25
0.66
60
25
0.28
0.82
48
24
0.18
1.32
53
27
0.2
1.48
60
30
0.22
1.65
75
38
0.26
2.06
58
32
0.16
2.14
63
35
0.18
2.3
72
40
0.20
2.63
90
50
0.24
3.29
38
0.20
0.33
42
0.22
0.38
48
0.25
0.44
60
10
0.28
0.55
48
11
0.18
0.88
53
13
0.2
0.99
60
14
0.22
1.10
75
18
0.26
1.37
58
16
0.16
1.43
63
18
0.18
1.53
72
20
0.20
1.75
90
25
0.24
2.19
38
22
0.25
0.82
42
25
0.28
0.95
48
28
0.30
1.10
60
35
0.35
1.37
48
27
0.22
2.19
53
30
0.24
2.47
60
34
0.26
2.74
75
43
0.30
3.43
58
32
0.20
3.57
63
35
0.21
3.84
72
40
0.22
4.39
90
50
0.26
5.49
38
22
0.27
0.66
42
25
0.3
0.77
48
28
0.32
0.88
60
35
0.37
1.10
48
27
0.24
1.76
53
30
0.26
1.97
60
34
0.28
2.19
75
43
0.32
2.74
58
32
0.22
2.85
63
35
0.21
3.07
72
40
0.24
3.51
90
50
0.27
4.39
38
0.16
0.33
42
0.17
0.38
48
0.18
0.44
60
10
0.20
0.55
48
11
0.14
0.88
53
13
0.15
0.99
60
14
0.16
1.10
75
18
0.18
1.37
58
16
0.12
1.43
63
18
0.13
1.53
72
20
0.14
1.75
90
25
0.16
2.19
MILLING
y FOR RAMPING
a When machining steel the recommended
& 32, & 33, & 35

Feed
(mm/rev)
Step
(mm)
&40
Feed
(mm/rev)
&50
Step
(mm)
Feed
(mm/rev)
Step
(mm)
0.055
0.3
0.06
0.3
0.065
0.3
0.05
0.3
0.055
0.3
0.06
0.3
0.05
0.25
0.055
0.25
0.06
0.25
0.065
0.5
0.07
0.5
0.075
0.5
0.065
0.3
0.07
0.3
0.075
0.3
0.04
0.25
0.045
0.25
0.05
0.25
ramping angle is 3. If a ramping angle

larger than 3 is used, then the chips may
not be broken effectively resulting in chips
wrapping around the tool.
a During ramping, it is recommended to
reduce the feed rate by 40% from the cutting
conditions on page L080.
TECHNICAL DATA
Q001
L083
INDEXABLE MILLING
Including
Flat faces
Roughing
DAH
DC DCCB
DCX
inserts.
a High rigidity double
clamp structure.
machining.
holes.
a Special insert design
with 3 cutting edges.
HSC10030H
16
M10 x 1.5
30
40
HSC16040H
24
AJX12-050A03R
50
38.3 50 22
AJX12R05003B
50
38.3 50 22.225 19 11
47
AJX14-063A03R
63
51.1 50 22
60 10.4 6.3 17 0.7
AJX14R06303B
63
51.1 50 22.225 19 11
60
8.4 5
17 0.7
AJX14R08004D
80
68.1 63 31.75
32 17
76 12.7 8
26 1.3
AJX14R10005D
5 100
88.1 63 31.75
32 17
96 12.7 8
26 2.4
AJX14R12505E
5 125 113.2 63 38.1
40
100 15.9 10
56 3.3
AJX14R16006F
6 160 148.2 63 50.8
43
100 19.1 11
72 5.0
AJX12-050A04R
50
38.3 50 22
20 11
AJX12R05004B
50
38.3 50 22.225 19 11
AJX14-063A04R
63
51.1 50 22
AJX14R06304B
63
51.1 50 22.225 19 11
60
8.4 5
17 0.7
AJX14R08005D
80
68.1 63 31.75
32 17
76 12.7 8
26 1.3
AJX14R10006D
6 100
88.1 63 31.75
32 17
96 12.7 8
26 2.4
AJX14R12507E
7 125 113.2 63 38.1
40
100 15.9 10
56 3.3
AJX14R16008F
8 160 148.2 63 50.8
43
100 19.1 11
72 5.0
AJX09-050A05R
50
40
50 22
20 11
AJX09R05005B
50
40
50 22.225 19 11
AJX12-063A05R
63
51.3 50 22
AJX12R06305B
63
51.3 50 22.225 19 11
AJX12R08006D
80
68.3 63 31.75
32 17
76 12.7 8
26 1.7
AJX12R10007D
7 100
88.3 63 31.75
32 17
96 12.7 8
26 2.9
Stock
Number of Teeth
DCX
Order Number
L084
L8
M24 x 3.0
45
59
17
*1
*1
WT
(kg)
DC
LF DCON CBDP DAH BD KWW L8 DCCB
20 11
20 11
20 11
20 11
47 10.4 6.3 17 0.4

8.4 5
17 0.4
47 10.4 6.3 17 0.4

47
8.4 5
17 0.4
Clamp Clamp Clamp Bridge Spring Wrench Set Bolt

Screw Bridge Screw
TS43
AMS4
HSC100
30H
TS54
JDMp
AJS50
HSC160 1405pp
AMS5 14T25 ASS3 zTKY25T
40H ZDpR-pp
MBA200
40H
MBA240
45H
TS43
AMS4
JDMp
HSC100
AJS40
ASS2 zTKY15T
1204pp
30H
12T15
ZDpR-pp
60 10.4 6.3 17 0.7
47 10.4 6.3 17 0.5

47
8.4 5
17 0.5
HSC100
30H
TS54
JDMp
AJS50
HSC160 1405pp
40H ZDpR-pp
MBA200
40H
MBA240
45H
TS351 AMS3
JDMp
HSC100
AJS30
ASS2 xTKY10D
09T3pp
30H
10T10
ZDpR-pp
60 10.4 6.3 17 0.9

60
8.4 5
17 0.9
Insert
JDMp
HSC100
AJS40
ASS2 zTKY15T
1204pp
30H
12T15
ZDpR-pp
TS43
AJS40
Torque (N m) : TS351=2.5, TS43=3.5, TS54=7.5, AJS3010T10=2.5, AJS4012T15=3.5, AJS5014T25=7.5

*12 Clamp
Refer to page L091 for the max. depth of cut APMX and maximum drilling depth AZ.
*3 WT : Tool Weight
*
40
54
MBA24045H
40
56
14
Dimensions(mm)
M20 x 2.5
17
M16 x 2.0
Type
Coarse Pitch
Fine Pitch
Extra Fine Pitch
MILLING
MBA20040H
Set Bolt
AJX09
AJX12
AJX14
GAMP :+8 GAMP :+8
GAMP :+8
GAMF :-6 GAMF :-5 -4 GAMF :-3
DCCB
DC
DCX
APMX*2
LF
a 13 and 15 positive
y ARBOR TYPE
CBDP
AZ
*2
50
65
K
Cast Iron
APMX*2
LF
M
Stainless Steel
AZ
*2
P
Steel
BD
DCON
KWW
125
160
L8
AJX
BD
DCON
KWW
50
63
80
100
CBDP
MULTI FUNCTIONAL
MILLING
HSC100
30H
JDMp
1204pp
HSC160 ZDpR-pp
40H
HSC16040H
Set Bolt
HSC10030H
For metric arbor
MBA20040H
M20 x 2.5
50
18
10
35
47
40
54
17
*1
*1
DCX
AJX12-050A03R
50
38.3 50
22
20 11
47 10.4 6.3 17 0.4
AJX14-063A03R
63
51.1 50
22
20 11
60 10.4 6.3 17 0.7
HSC100
30H
AJX14-080A04R
80
68.1 50
27
23 13
76 12.4 7.0 19 1.2
HSC120
35H
Dimensions(mm)
WT
(kg)
DC
Clamp Clamp Clamp Bridge Spring Wrench Set Bolt

Screw Bridge Screw
LF DCON CBDP DAH BD KWW L8 DCCB
TS43 AMS4
JDMp
HSC100
AJS40
ASS2 zTKY15T
1204pp
30H
12T15
ZDpR-pp
AJS50
2.4 TS54 AMS5 14T25 ASS3 zTKY25T
HSC160
40H
AJX14-100A05R
100
88.1 63
32
26 17
AJX14-125B05R
125 113.2 63
40
40
100 16.4 9.0 56 3.3
AJX14-160B06R
160 148.2 63
40
40
100 16.4 9.0 56 5.0
AJX12-050A04R
50
38.3 50
22
20 11
47 10.4 6.3 17 0.4
AJX12-080A06R
80
68.3 50
27
23 13
AJX12-100A07R
100
88.3 63
32
26 17
AJS40
76 12.4 7.0 19 1.2 TS43 AMS4 12T15 ASS2 zTKY15T
96 14.4 8.0 26 2.6
AJX14-063A04R
63
51.1 50
22
20 11
60 10.4 6.3 17 0.7
HSC100
30H
AJX14-080A05R
80
68.1 50
27
23 13
76 12.4 7.0 19 1.2
HSC120
35H
96 14.4 8.0 26
100
88.1 63
32
26 17
AJX14-125B07R
125 113.2 63
40
40
100 16.4 9.0 56 3.3
AJX14-160B08R
160 148.2 63
40
40
100 16.4 9.0 56 5.0
AJX09-050A05R
50
40
50
22
20 11
47 10.4 6.3 17 0.4
AJX12-063A05R
63
51.3 50
22
20 11
60 10.4 6.3 17 0.7
96 14.4 8.0 26
JDMp
1405pp
ZDpR-pp
MBA200
40H
HSC100
30H
AJS50
2.4 TS54 AMS5 14T25 ASS3 zTKY25T
AJX14-100A06R
Insert
HSC120
35H
HSC160
40H
HSC160
40H
JDMp
1204pp
ZDpR-pp
JDMp
1405pp
ZDpR-pp
MBA200
40H
TS351 AMS3
JDMp
HSC100
AJS30
ASS2 xTKY10D
09T3pp
30H
10T10
ZDpR-pp
TS43 AMS4
JDMp
HSC100
AJS40
ASS2 zTKY15T
1204pp
30H
12T15
ZDpR-pp
Torque (N m) : TS351=2.5, TS43=3.5, TS54=7.5, AJS3010T10=2.5, AJS4012T15=3.5, AJS5014T25=7.5

*12 Clamp
Refer to page L091 for the max. depth of cut APMX and maximum drilling depth AZ.
*3 WT : Tool Weight
*
SPARE PARTS
TECHNICAL DATA
P001
Q001
MILLING
Order Number
Stock
R
Number of Teeth
Type
Coarse Pitch
Fine Pitch
Extra Fine Pitch
40
56
14
M12 x 1.75

y ARBOR TYPE
30
40
HSC12035H
AJX09
AJX12
AJX14
GAMP :+8 GAMP :+8
GAMP :+8
GAMF :-6 GAMF :-5 -4 GAMF :-3
M16 x 2.0
24
16
M10 x 1.5
L085
DCON
AZ
*2
DC
DCX
INDEXABLE MILLING
APMX*2
B2
(Corresponding Inclination Angle)
LH
LF
16
AJX06R172SA16SS
AJX06R162SA16S
AJX06R172SA16S
Short
Standard
Stock
AJX06R162SA16SS
*1
Dimensions(mm)
DCX DCON
B2
*1
Clamp Clamp Clamp Bridge Spring Wrench

Screw Bridge
Screw
DC
LF
LH
16
8.9
70
20
17
16
9.9
70
20
16
16
8.9
110
30
17
16
9.9
110
20
AJX06R203SA20S
20
20
12.9
130
50
AJX06R223SA20S
22
20
14.9
130
30
AJX08R202SA20S
20
20
11.4
130
50
AJX08R222SA20S
22
20
13.4
130
30
AJX08R253SA25S
25
25
16.4
140
60
AJX08R283SA25S
28
25
19.4
140
40
AJX09R252SA25S
25
25
14.9
140
60
AJX09R282SA25S
28
25
17.9
140
40
AJX09R303SA32S
30
32
20.0
150
70
148 TS351 AMS3 AJS3010T10 ASS2 xTKY10D
AJX09R323SA32S
32
32
21.9
150
70
AJX09R353SA32S
35
32
24.9
150
50
AJX09R404SA32S
40
32
29.9
150
50
AJX09R404SA42S
40
42
29.9
150
70
AJX12R302SA32S
30
32
18.3
150
70
AJX12R322SA32S
32
32
20.3
150
70
058 TS43
AJX12R352SA32S
35
32
23.3
150
50
TS43
AMS4 AJS4012T15 ASS2 xTKY15D
AJX12R403SA32S
40
32
28.3
150
50
TS43
AJX12R403SA42S
40
42
28.3
150
70
148 TS43
AJX14R503SA42S
50
42
38.2
150
50
TS54
AJX14R634SA42S
63
42
51.1
150
50
TS54
330 TS25
Insert
TS25
zTKY08F JOMp06T215
zTKY08F ZZpR-pp
215 TS25
zTKY08F
TS25
zTKY08F
118 TS25
TS25
zTKY08F
120 TS33
xTKY08D
TS33
xTKY08D
106 TS33
JOMp
080320
xTKY08D ZZpR-pp
xTKY08D
TS33
JOMp
06T215
zTKY08F ZZpR-pp
TS351 AMS3 AJS3010T10 ASS2 xTKY10D
JDMp
09T3pp
ZDpR-pp
JDMp
1204pp
ZDpR-pp
AMS5 AJS5014T25 ASS3 xTKY25D JDMp1405pp

AMS5 AJS5014T25 ASS3 xTKY25D ZDpR-pp
1 Clamp Torque (N m) : TS25=1.0, TS33=1.0, TS351=2.5, TS407=3.5, TS43=3.5, TS54=7.5, AJS3010T10=2.5, AJS4012T15=3.5,
AJS5014T25=7.5
2 Refer to page L091 for the max. depth of cut APMX(max), and maximum drilling depth AZ.
L086
Order Number
MILLING
*
*

Number of Teeth
Type
y SHANK TYPE
63
*1
AJX06R162SA16L
16
16
8.9 150
70 056 TS25
zTKY08F
AJX06R172SA16L
17
16
9.9 150
20
TS25
zTKY08F
AJX06R203SA20L
20
20
12.9 180
100 038 TS25
JOMp
06T215
zTKY08F ZZpR-pp
AJX06R223SA20L
22
20
14.9 180
TS25
zTKY08F
AJX08R202SA20L
20
20
11.4 180
100 039 TS33
xTKY08D
AJX08R222SA20L
22
20
13.4 180
TS33
xTKY08D
AJX08R253SA25L
25
25
16.4 200
120 032 TS33
JOMp
080320
xTKY08D ZZpR-pp
AJX08R283SA25L
28
25
19.4 200
xTKY08D
AJX09R252SA25L
25
25
14.9 200
AJX09R282SA25L
28
25
17.9 200
AJX09R303SA32L
30
32
20.0 200
120 102 TS351 AMS3 AJS3010T10 ASS2 xTKY10D
AJX09R323SA32L
32
32
21.9 200
AJX09R353SA32L
35
32
24.9 200
50
AJX09R404SA32L
40
32
29.9 250
50
AJX09R404SA42L
40
42
29.9 250
AJX12R302SA32L
30
32
18.3 200
AJX12R322SA32L
32
32
20.3 200
120 033 TS43
AJX12R352SA32L
35
32
23.3 200
50
TS43
AJX12R403SA32L
40
32
28.3 250
50
TS43
AJX12R403SA42L
40
42
28.3 250
70 148 TS43
AJX14R503SA42L
50
42
38.1 250
50
TS54
AJX14R634SA42L
63
42
51.1 250
50
TS54
AMS5 AJS5014T25 ASS3 xTKY25D JDMp1405pp

AJX06R162SA16EL
16
16
8.9 200
AJX06R172SA16EL
17
16
9.9 200
AJX08R202SA20EL
20
20
11.4 250
AJX08R222SA20EL
22
20
13.4 250
AJX09R252SA25EL
25
25
14.9 300
AJX09R282SA25EL
28
25
17.9 300
180 022 TS351 AMS3 AJS3010T10 ASS2 xTKY10D JDMp09T3pp

TS351 AMS3 AJS3010T10 ASS2 xTKY10D ZDpR-pp
40
AJX12R302SA32EL
30
32
18.3 300
AJX12R322SA32EL
32
32
20.3 300
180 022 TS43
AJX12R352SA32EL
35
32
23.3 300
50
TS43
AJX12R402SA32EL
40
32
28.3 350
50
TS43
AJX12R402SA42EL
40
42
28.3 350
70 148 TS43
DCX DCON
DC
LF
LH
30
30
40
B2

Screw Bridge
Screw
TS33
Insert

40
100 038 TS25
TS25
130 030 TS33
20
30
TS33
JDMp
09T3pp
ZDpR-pp
JDMp
1204pp
ZDpR-pp
zTKY08F JOMp06T215
zTKY08F ZZpR-pp
xTKY08D JOMp080320
xTKY10D ZZpR-pp
MILLING
Order Number
Stock
R
Number of Teeth
Type
Long
Extra Long
*1
Dimensions(mm)
JDMp
1204pp
ZDpR-pp
TS33=1.0, TS351=2.5, TS407=3.5, TS43=3.5, TS54=7.5, AJS3010T10=2.5, AJS4012T15=3.5,

*1 Clamp Torque (N m) : TS25=1.0,
AJS5014T25=7.5
*2 Refer to page L091 for the max. depth of cut APMX(max), and maximum drilling depth AZ.
SPARE PARTS
TECHNICAL DATA
P001
Q001
L087
INDEXABLE MILLING
Fig.2
Fig.1
CRKS
H
BD
DCON
DC
DCX
A
AZ
*2
Fig.3
APMX*2
A-A section
L11
LF
OAL
y SCREW-IN TYPE
*1
16
8.5 13
8.9 48
30
10 M8
0.1 1 TS25
zTKY08F
AJX06R172AM0830
17
8.5 13
9.9 48
30
10 M8
0.1 1 TS25
zTKY08F
AJX06R203AM1030
20 10.5 18 12.9 49
30
14 M10 0.1 3 TS25
AJX06R223AM1030
22 10.5 18 14.9 49
30
14 M10 0.1 3 TS25
zTKY08F
AJX08R202AM1030
20 10.5 18 11.4 49
30
14 M10 0.1 2 TS33
zTKY08D
AJX08R222AM1030
22 10.5 18 13.4 49
30
14 M10 0.1 2 TS33
zTKY08D
AJX08R253AM1235
25 12.5 21 16.4 57
35
19 M12 0.1 1 TS33
JOMp
080320
zTKY08D ZZpR-pp
AJX08R283AM1235
28 12.5 21 19.4 57
35
19 M12 0.1 1 TS33
zTKY08D
AJX09R252AM1235
25 12.5 21 14.9 57
35
19 M12 0.2 2 TS351 AMS3 AJS3010T10 ASS2 xTKY10D
AJX09R282AM1235
28 12.5 21 17.9 57
35
AJX09R303AM1645
30 17
29 20.0 68
45
AJX09R323AM1645
32 17
29 21.9 68
45
JDMp
09T3pp
24 M16 0.2 1 TS351 AMS3 AJS3010T10 ASS2 xTKY10D ZDpR-pp
AJX09R353AM1645
35 17
29 24.9 68
45
AJX09R404AM1645
40 17
29 29.9 68
45
AJX12R302AM1645
30 17
29 18.3 68
45
AJX12R322AM1645
32 17
29 20.3 68
45
24 M16 0.3 2 TS43
AJX12R352AM1645
35 17
29 23.3 68
45
24 M16 0.3 2 TS43
JDMp
1204pp
AJX12R403AM1645
40 17
29 28.3 68
45
24 M16 0.3 2 TS43
*
WT
Dimensions(mm)
(kg)
DCX DCON BD DC OAL LF L11
CRKS
Type (Fig.)
Coolant Hole
AJX06R162AM0830
Stock
Number of Teeth
MILLING
Order Number
z x

Screw Bridge
Screw
*
*
*
Insert
JOMp
06T215
zTKY08F ZZpR-pp

1 Clamp Torque (N m) : TS25=1.0, TS33=1.0, TS351=2.5, TS407=3.5, TS43=3.5, AJS3010T10=2.5, AJS4012T15=3.5
2 Refer to page L091 for the max. depth of cut APMX(max), and maximum drilling depth AZ.
3 WT : Tool Weight
L088

1
INSERTS
Work
Material
P
M
K
S
H
Steel

: Stable Cutting
: General Cutting
Stainless Steel
Hardened Steel
General
purpose
Order Number
Dimensions (mm)
Class
FH7020
N
MP6120 EW
N
MP6130 EW
N
MP7130 EW
N
MP7140 EW
N
MP9120 EW
N
MP9130 EW
VP15TF
VP30RT
Coated
Shape
: Unstable Cutting
Cast Iron
AN
IC
BS
RE
JOMW06T215ZZSR-FT M
a a a a a
a a
13
6.35
2.78
1.2
1.5
JOMW080320ZZSR-FT M
a a a a a
a a
13
3.18
1.4
JDMW09T320ZDSR-FT M
a a a a a
a a
15
9.525 3.97
1.8
JDMW120420ZDSR-FT M
a a a a a
a a
15 12
4.76
2.5
JDMW140520ZDSR-FT M
a a a a a
a a
15 14
5.56
2.8
JDMT120420ZDSR-ST
a a a a a
a a
15 12
4.76
2.5
JDMT140520ZDSR-ST
a a a a a
a a
15 14
5.56
2.8
Geometry
AN
BS
IC
RE
AN
BS
IC
RE
Cutting edge
enhancement type
JDMT09T323ZDER-JL
a a
15
JDMT120423ZDER-JL
a a
15 12
JDMT140523ZDER-JL
a a
15 14
9.525 3.97
1.8
2.3
4.76
2.5
2.3
5.56
2.8
2.3
AN
BS
IC
Low cutting resistance

(Difficult-to-Cut Materials)
JOMT06T215ZZSR-JM M
a a a a a
a a
13
6.35
2.78
1.2
1.5
JOMT080320ZZSR-JM M
a a a a a
a a
13
3.18
1.4
JDMT09T320ZDSR-JM M
a a a a a
a a
15
9.525 3.97
1.8
JDMT120420ZDSR-JM M
a a a a a
a a
15 12
2.5
2.8
4.76
AN
BS
IC
RE
MILLING
Low cutting
a a a a a
a a
15 14
5.56
resistance JDMT140520ZDSR-JM M
(Note) Setting height for ST chipbreaker is slightly different from that for other chipbreakers.
If you use ST chipbreaker, check the setting height.
RE
SCREW-IN ARBORS
SPARE PARTS
TECHNICAL DATA
L145
P001
Q001
L089
INDEXABLE MILLING

y CUTTING SPEED
Work Material
MP6120
MP6130
VP30RT
150
(100200)
130
(80180)
110
(60160)
Mild Steel
180HB
Carbon Steel
Alloy Steel
180280HB
150
(100200)
130
(80180)
110
(60160)
90
(40140)
Carbon Steel
Alloy Steel
280350HB
130
(80180)
100
(50150)
80
(30130)
60
(20110)
Alloy Tool Steel
350HB
130
(80180)
100
(50150)
80
(30120)
60
(2090)
Pre-hardened Steel
3545HRC
100
(70130)
80
(50110)
80
(3090)
MP7130
MP7140
140
(100180)
120
(80160)
FH7020
VP15TF
Stainless Steel
270HB
K
Gray Cast Iron
350MPa
150
(100200)
Ductile Cast Iron
800MPa
120
(80160)
MP9120
MP9130
350HB
30
(2040)
25
(2035)
50
(4060)
45
(3055)
S
Titanium Alloy
VP15TF
H
Hardened Steel
MILLING
FH7020
170
(120220)
L090
Cutting speed (m/min) for different grades
Hardness
4055HRC
70
(5090)
MAXIMUM CAPACITIES BY MODE

y RAMPING
y HELICAL DRILLING
L
a How to derive a locus of the center of the tool.
RMPX
X(mm)
DCX
dc = DH - DC
Locus of
the center of
the tool
Desired hole
diameter
Tool
Diameter
a The depth of cut per pass must not exceed the
max. depth of cut APMX.

dc
a Set the machine spindle revolution so that the
DH
tool is rotating and cutting in a down cut direction.
Arbor
Order Number
AJX06R162
AJX06R172
AJX06R203
AJX06R223
AJX08R202
AJX08R222
AJX08R253
AJX08R283
AJX09R252
AJX09R282
AJX09R303
AJX09R323
AJX09R353
AJX09R404
AJX12R302
AJX12R322
AJX12R352
AJX12R402
AJX12R403
AJX14R503
AJX14R634
AJX09-050
AJX09R05005B
AJX12-050
AJXR050
AJX12-063
AJXR063
AJXR080
AJXR100
AJX14-063
AJXR063
AJXR080
AJXR100
AJXR125
AJXR160
Tool Machined
Face
Diameter Diameter
DCX
DC
Max. Depth of Cut

APMX
(mm)
JL
FT/JM/ST
Breaker Breaker
Max.
Drilling
Max. L (mm) Required distance for X mm depth Desired hole diameter DH (mm) Depth
Angle
AZ
X=1
X=1.2
X=1.5
X=2
Min.
Max.
(mm)
RMPX
Ramping
Helical Drilling
(mm)
(mm)
16
17
8
9
1
1
3
2 30
19.1
22.9
23
25
29
31
0.3
0.3
20
12
1 30
38.2
31
37
0.3
22
14
57.3
35
41
0.3
20
11
1.5
3 30
16.3
19.6
24.5
27
36
0.5
22
13
1.5
19.1
22.9
28.6
31
40
0.5
25
16
1.5
28.6
34.4
43
37
46
0.5
28
19
1.5
1 42
33.7
40.4
50.5
43
52
0.5
25
14
1.2
14.3
17.2
21.5
28.6
33
46
28
17
1.2
19.1
22.9
28.6
38.1
39
52
30
19
1.2
2 42
21.2
25.4
31.8
42.4
43
56
32
21
1.2
2 30
22.9
27.5
34.4
45.8
47
60
35
24
1.2
28.6
34.4
43
57.3
53
66
40
29
1.2
1 30
38.2
45.8
57.3
76.4
63
76
30
18
1.2
4 30
12.7
15.2
19
25.4
39
56
1.5
32
20
1.2
14.3
17.2
21.4
28.6
41
60
1.5
35
23
1.2
3 30
16.3
19.6
24.5
32.7
47
66
1.5
40
28
1.2
19.1
22.9
28.6
38.2
57
76
1.5
40
28
1.2
19.1
22.9
28.6
38.2
57
76
1.5
50
63
38
51
2
2
1.2
1.2
4 12
2 48
13.6
20.4
16.3
24.5
20.4
30.7
27.2
40.9
72
98
96
122
2
2
50
50
40
40
2
2
1.2
1.2
1 06
1 06
52.1
52.1
62.5
62.5
78.1
78.1
104.2
104.2
83
83
96
96
1
1
50
38
1.2
28.6
34.4
43
57.3
77
96
1.5
50
38
1.2
28.6
34.4
43
57.3
77
96
1.5
63
51
1.2
1 30
38.2
45.8
57.3
76.4
103
122
1.5
63
51
1.2
1 30
38.2
45.8
57.3
76.4
103
122
1.5
80
68
1.2
1 06
52.1
62.5
78.1
104.2
137
156
1.5
100
88
1.2
0 48
71.6
85.9
107.4
143.2
177
196
1.5
63
51
1.2
2 48
20.4
24.5
30.7
40.9
98
122
63
51
1.2
2 48
20.4
24.5
30.7
40.9
98
122
80
68
1.2
1 48
31.8
38.2
47.7
63.6
132
156
100
88
1.2
1 12
47.7
57.3
71.6
95.5
172
196
125
160
113
148
2
2
1.2
1.2
0 48
0 30
71.6
114.6
85.9
137.5
107.4
171.9
143.2
229.2
222
292
246
316
2
2
MILLING
Shank/screw-in
Type
a When ramping and helical cutting, please apply a lower feed (60% of the calculated feed rate or less).
a When drilling, please set the feed in the axial direction at 0.2mm/rev or less.
a The long chips generated can disperse, ensure that adequate safety precautions are taken.
L091
INDEXABLE MILLING

y DEPTH OF CUT AND FEEDRATE
Shank Type / Screw-In Type
16, 17
Work Material
Hardness
Mild Steel
< 180HB

(AISI 1045, AISI 4140)
180280HB
280350HB
(AISI 4340)
Alloy Tool Steel
< 350HB
(SKD,SKT)
Pre-hardened Steel
3545HRC
< 270HB
Stainless Steel
Gray Cast Iron
Tensile Strength
< 350MPa
(FC300)
Ductile Cast Iron
(FCD450)
Tensile Strength
< 800MPa
350HB
Titanium Alloy (Ti-6A-4V)
Hardened Steel
4055HRC
MILLING
(SKD,SKT)
20, 22
25, 28
Overhang Axial depth Feed per Overhang Axial depth Feed per Overhang Axial depth Feed per
Length of cut
Tooth
Length of cut
Tooth
Length of cut
Tooth
(mm)
(mm)
(mm/t.)
(mm)
(mm)
(mm/t.)
(mm)
(mm)
(mm/t.)
1.2
140
0.8
0.8
160
1.0
1.0
170
1.0
180
0.6
0.6
210
0.8
0.8
230
0.8
1.0
210
0.4
0.4
240
0.6
0.6
290
0.6
0.8
1.2
140
0.8
0.8
160
1.0
1.0
170
1.0
180
0.6
0.6
210
0.8
0.8
230
0.8
1.0
210
0.4
0.4
240
0.6
0.6
290
0.6
0.8
1.2
140
0.7
0.8
160
0.8
1.0
170
0.8
180
0.5
0.6
210
0.6
0.8
230
0.6
1.0
210
0.3
0.4
240
0.4
0.6
290
0.4
0.8
1.2
140
0.7
0.8
160
0.8
1.0
170
0.8
180
0.5
0.6
210
0.6
0.8
230
0.6
1.0
210
0.3
0.4
240
0.4
0.6
290
0.4
0.8
140
0.7
0.7
160
0.8
0.8
170
0.8
1.0
180
0.5
0.5
210
0.6
0.6
230
0.6
0.8
0.6
210
0.3
0.3
240
0.4
0.4
290
0.4
140
0.8
0.7
160
1.0
0.8
170
1.0
1.0
180
0.6
0.5
210
0.8
0.6
230
0.8
0.8
0.6
210
0.4
0.3
240
0.6
0.4
290
0.6
140
0.8
1.0
160
1.0
1.2
170
1.0
1.4
180
0.6
0.8
210
0.8
1.0
230
0.8
1.2
210
0.4
0.6
240
0.6
0.8
290
0.6
1.0
140
0.7
0.8
160
0.8
1.0
170
0.8
1.2
180
0.5
0.6
210
0.6
0.8
230
0.6
1.0
210
0.3
0.4
240
0.4
0.6
290
0.4
0.8
170
1.0
0.6
230
0.8
0.4
290
0.6
0.3
140
0.5
0.5
160
0.5
0.6
170
0.5
0.8
180
0.4
0.3
210
0.4
0.4
230
0.4
0.6
210
0.3
0.2
240
0.3
0.2
290
0.3
0.4
cTable Feed Rate
zOverhang Length L
vf(mm/min)=n x Feed per Tooth x Number of Teeth
vRecommended width of cut (ae) is more than 60% of the cutting edge diameter.
bThe above cutting conditions are guides to cutting on a #50 BT machine. In case of
Overhang
Length
#40 BT and #63 HSK machines, a cutting edge diameter of under 35mm is
recommended.In the case also, reduce the axial direction depth of cut and table
feed rate.
nUse of ST chipbreaker with tougher cutting edges is recommended for machining

parts that require interrupted cutting. First recommended insert grade for
non-standard 06/08/09 ST chipbreakers is VP30RT irrespective of the workpiece
material.
mCutter body with coarse pitch is recommended for the unstable cutting caused by
the long tool overhang.
xMain Spindle Revolution

n(min-1)=(Recommended Cutting Speed x 1000)u
(Outer Tool Diameter x 3.14)
,Use the "sharp" JM chipbreaker to lower cutting forces or when long tool
overhangs are used.
.Heavy chips are generated when machining with the AJX. To avoid chip
jamming-related problems, use air blow while machining to discharging chips
effectively.
L092
Shank Type / Screw-In Type

&40 (&42 Shank)
Arbor Type
&40 (&32 Shank)
30, 32, 35
50, 63
50, 63
80, 100, 125, 160
Overhang Axial depth Feed per Overhang Axial depth Feed per Overhang Axial depth Feed per Overhang Axial depth Feed per Overhang Axial depth Feed per Overhang Axial depth Feed per
Length of cut
Tooth
Length of cut
Tooth
Length of cut
Tooth
Length of cut
Tooth
Length of cut
Tooth
Length of cut
Tooth
(mm)
(mm)
(mm)
(mm)
(mm/t.)
(mm)
(mm)
(mm/t.)
(mm)
(mm)
(mm/t.)
(mm)
(mm)
(mm/t.)
(mm)
(mm)
(mm/t.)
180
1.2
1.4
180
1.2
1.4
180
1.2
1.5
180
1.4
1.5
150
1.5
1.5
170
1.5
1.5
230
1.0
1.2
240
1.0
1.2
240
1.0
1.3
240
1.2
1.3
250
1.3
1.3
300
1.3
1.3
290
0.8
1.0
300
0.8
1.0
300
0.8
1.1
350
1.1
1.1
450
1.0
1.0
180
1.2
1.4
180
1.2
1.4
180
1.2
1.5
180
1.4
1.5
150
1.5
1.5
170
1.5
1.5
1.3
230
1.0
1.2
240
1.0
1.2
240
1.0
1.3
240
1.2
1.3
250
1.3
1.3
300
1.3
290
0.8
1.0
300
0.8
1.0
300
0.8
1.1
350
1.1
1.1
450
1.0
1.0
180
1.0
1.4
180
1.0
1.4
180
1.0
1.5
180
1.2
1.5
150
1.3
1.5
170
1.3
1.5
1.3
230
0.8
1.2
240
0.8
1.2
240
0.8
1.3
240
1.0
1.3
250
1.1
1.3
300
1.1
290
0.6
1.0
300
0.6
1.0
300
0.6
1.1
350
0.9
1.1
450
0.8
1.0
180
1.0
1.4
180
1.0
1.4
180
1.0
1.5
180
1.2
1.5
150
1.3
1.5
170
1.3
1.5
1.3
230
0.8
1.2
240
0.8
1.2
240
0.8
1.3
240
1.0
1.3
250
1.1
1.3
300
1.1
290
0.6
1.0
300
0.6
1.0
300
0.6
1.1
350
0.9
1.1
450
0.8
1.0
180
1.0
1.2
180
1.0
1.2
180
1.0
1.3
180
1.2
1.3
150
1.3
1.3
170
1.3
1.3
230
0.8
1.0
240
0.8
1.0
240
0.8
1.1
240
1.0
1.1
250
1.1
1.1
300
1.1
1.1
290
0.6
0.8
300
0.6
0.8
300
0.6
0.9
350
0.9
0.9
450
0.8
0.8
1.3
180
1.2
1.2
180
1.2
1.2
180
1.2
1.3
180
*1.4
1.3
150
*1.5
1.3
170
*1.5
230
1.0
1.0
240
1.0
1.0
240
1.0
1.1
240
1.2
1.1
250
*1.3
1.1
300
*1.3
1.1
290
0.8
0.8
300
0.8
0.8
300
0.8
0.9
350
1.1
0.9
450
1.0
0.8
180
1.2
1.6
180
1.2
1.6
180
1.2
1.7
180
1.4
1.7
150
1.5
1.7
170
1.5
1.7
230
1.0
1.4
240
1.0
1.4
240
1.0
1.5
240
1.2
1.5
250
1.3
1.5
300
1.3
1.5
290
0.8
1.2
300
0.8
1.2
300
0.8
1.3
350
1.1
1.3
450
1.0
1.2
180
1.0
1.4
180
1.0
1.4
180
1.0
1.5
180
1.2
1.5
150
1.3
1.5
170
1.3
1.5
230
0.8
1.2
240
0.8
1.2
240
0.8
1.3
240
1.0
1.3
250
1.1
1.3
300
1.1
1.3
290
0.6
1.0
300
0.6
1.0
300
0.6
1.1
350
0.9
1.1
450
0.8
1.0
180
1.2
0.6
180
1.2
0.6
180
1.2
0.6
180
1.2
0.6
150
1.2
0.6
170
1.2
0.6
230
1.0
0.4
240
1.0
0.4
240
1.0
0.4
240
1.0
0.4
250
1.0
0.4
300
1.0
0.4
290
0.8
0.3
300
0.8
0.3
300
0.8
0.3
350
0.8
0.3
450
0.8
0.3
180
0.6
1.0
180
0.6
1.0
180
0.6
1.1
180
0.8
1.1
150
0.9
1.1
170
0.9
1.1
230
0.5
0.8
240
0.5
0.8
240
0.5
0.9
240
0.6
0.9
250
0.7
0.9
300
0.7
0.9
290
0.4
0.6
300
0.4
0.6
300
0.4
0.7
The JL breaker depth of cut is up to 1.2mm.

MILLING
(mm/t.)
NOTE FOR PROGRAMMING
cut
Un
K
on
ti
por
RE
When using the AJX, please

programme as an R3 radius cutter.
The approximate uncut portions for
the programme are as follows.
Size
Breaker
06
08
FT / JM
FT / JM
FT / JM
JL
FT / JM / ST
JL
FT / JM / ST
JL
09
12
14
Approx. RE(mm) Uncut portion K(mm)
2.0
2.5
0.33
0.46
3.0
3.0
0.47
0.46
3.0
3.0
0.63
0.53
3.0
3.0
0.64
0.55
(Note) The uncut portion may change slightly depending on

cutting conditions.
TECHNICAL DATA
Q001
L093
INDEXABLE MILLING
MULTI FUNCTIONAL
MILLING
Roughing
OCTACUT
N
Stainless Steel
Cast Iron
AZ
36
Hardened Steel
DCON
Steel
DC
D10
DCX
(Inner)
14
3
42
A1
LH
LF
round type inserts.

DCX
OCTACUT322S32RB
32
OCTACUT403S32RB
40
OCTACUT504S32RB
OCTACUT634S32RB
OCTACUT503S32R
OCTACUT634S32R
Stock
Number of Teeth
Order Number
APMX
a For octagonal and
y SHANK TYPE
19
Dimensions (mm)
DC
D10
LF DCON LH
A1 APMX AZ
Clamp Screw
23.6 13.1
125
32
45
2.5
CS350990T zTKY10F
31.7 21.2
125
32
45
2.5
CS350990T zTKY10F
50
41.9 31.4
125
32
45
2.5
CS350990T zTKY10F
63
54.9 44.5
125
32
45
2.5
CS350990T zTKY10F
50
38.3 24.5
125
32
45
CS501290T xTKY25T
63
51.4 37.6
125
32
45
CS501290T xTKY25T
Wrench
Insert
zOEMX12T3pppp
xREMX12T3pppp
zOEMX1705pppp
xREMX1705pppp
Clamp Torque (N m) : CS350990T=2.5, CS501290T=7.5
INSERTS
Steel

: Stable Cutting
: General Cutting
Stainless Steel
Cast Iron
2
JS Breaker
OEMX12T3ESR1
OEMX12T3EER1-JS
Dimensions (mm)
IC
12.7
BS
3.97
1.0
M S
12.7
3.97
1.0
M E
12.7
3.97
1.0
OEMX1705ETR1
M T
17.0
5.0
1.4
OEMX1705ESR1
M S
17.0
5.0
1.4
*
*2
OEMX1705EER1-JS
M E
17.0
5.0
1.4
OEMX1705ETR1-JS
M T
17.0
5.0
1.4
*2
REMX12T3EN-JS
M E
12.95
4.17
REMX1705SN
M S
17.25
5.2
REMX1705EN-JS
M E
17.25
5.2
Geometry
BS
M T
CBN 1
20
IC
*2 JS Breaker
2.5
*2 Insert with breaker.
L094
*1 CBN Insert
20
IC
*JS2 Breaker
BS
OEMX12T3ETR1
Cermet
MB730
MILLING
Order Number
Class
Honing
F7030
VP15TF
Coated
Shape
: Unstable Cutting
Honing :
Hardened Steel
NX2525
NX4545
Work
Material
P
M
K
H
: Inventory maintained in Japan. (10 inserts in one case) (CBN inserts are available in 1 piece in one case.)
*2 JS Breaker
Fig.4
Small Insert Type

40
Standard Insert Type

50
KAPR :3
GAMP :+13
GAMF :-4
y ARBOR TYPE
Order Number
Small
Insert Type
Standard
Insert Type
50
63
80
63
80
100
A1
APMX
DCCB
D10
DC
DCX
AZ
A1
APMX
DCCB
D10
DC
DCX
AZ
A1
APMX
AZ
DAH
D10
DC
DCX
APMX
A1
D10
DC
DCX
AZ
LF
LF
L8
CBDP
L8
BD
DCON
KWW
CBDP
L8
BD
DCON
KWW
CBDP
CBDP
L8
Set Bolt
Fig.3
BD
DCON
KWW
LF
Fig.2
BD
LF
Fig.1
125
160
Stock Number
R of Teeth DCX
DC
D10
* Max. Depth of Cut Type
Dimensions (mm)
LF DCON CBDP DAH DCCB KWW BD
L8
WT
(kg)
A1 APMX AZ (Fig.)
OCTACUT0403ARB
40
31.7
21.2 40 16
18
8.4 33
5.6
0.4
2.5
OCTACUT0504ARB
50
41.9
31.4 50 22
20
11
10.4 42.5
6.3
0.5
2.5
OCTACUT0634ARB
63
54.9
44.5 50 22
20
11
10.4 44
6.3
0.7
2.5
OCTACUT0805CRB
80
71.9
61.5 50 25.4
26
13
9.5 53
1.2
2.5
OCTACUT0503AR
50
38.3
24.5 50 22
20
10.4 41
6.3
0.5
OCTACUT0634AR
63
51.4
37.6 50 22
20
11
10.4 44
6.3
0.7
OCTACUT0805CR
80
68.4
54.7 50 25.4
26
13
9.5 53
1.2
OCTACUT1006DR
100
88.5
74.7 63 31.75
32
17
12.7 70
1.6
OCTACUT1257ER
125 113.5
99.8 63 38.1
35
60
15.9 80
10
1.8
OCTACUT1608FR
160 148.5 134.8 63 50.8
38
80.9 19.1 120
11
3.6
* WT : Tool Weight
SPARE PARTS
*
Clamp Screw
OCTACUT0403ARB
OCTACUT0504ARB
OCTACUT0634ARB
OCTACUT0805CRB
OCTACUT0503AR
OCTACUT0634AR
OCTACUT0805CR
OCTACUT1006DR
OCTACUT1257ER
OCTACUT1608FR
CS350990T
CS501290T
Wrench
TKY10F
Wrench
Set Bolt
Set Bolt
HDS08030
BOES101
Insert
HDS10031
BOES101
HSC16035
TKY25T
zOEMX12T3pppp
xREMX12T3pppp
MILLING
Tool Holder Number
zOEMX1705pppp
xREMX1705pppp
* Clamp Torque (N m) : CS350990T=2.5, CS501290T=7.5

APPLICATION
DCX
R Corner Milling
Max. Depth of Cut
Face Milling
Drilling
Maximum cutting depth is

4mm with the inside
cutting edge.
2DCX
Contouring
Pocket Milling
Approx.1.2
(Max.)
42
Approx.0.1
(Wall Face Geometry)
Core
Core
C5
Minimum Width to
Eliminate Core
DCX
42
2DCX
5 (Max.)
DCX
4 (Max.)
42
Deep Shoulder Milling
Chamfer Milling
Above sizes are for OEMX1705pppp.

SPARE PARTS
TECHNICAL DATA
P001
Q001
L095
INDEXABLE MILLING
L8
CBDP
CBDP
14
KAPR :3
GAMP :+13
GAMF :-4
y ARBOR TYPE
Order Number
DCCB
66.7
D10
DC
DCX
A1
APMX
DCCB
D10
DC
DCX
AZ
AZ
DAH
D10
DC
DCX
A1
APMX
D10
DC
DCX
A1
APMX
For metric arbor
AZ
AZ
A1
APMX
LF
LF
BD
DCON
KWW
L8
BD
DCON
KWW
CBDP
L8
CBDP
Set Bolt
Fig.4
LF
BD
DCON
KWW
BD
Fig.3
LF
Fig.2
L8
Fig.1
Stock Number
R of Teeth DCX
DC
D10
LF
* Max. Depth of Cut Type
Dimensions (mm)
DMM CBDP DAH DCCB KWW BD
L8
WT
(kg)
A1 APMX AZ (Fig.)
5.6
0.4
2.5
OCTACUT0403ARB
40
31.7
21.2
40
16
18
OCTACUT0504ARB
50
41.9
31.4
50
22
20
11
10.4 42.5 6.3
0.5
2.5
OCTACUT0634ARB
63
54.9
44.5
50
22
20
11
10.4 44
6.3
0.7
2.5
OCTACUT0805ARB
80
71.9
61.5
50
27
23
13
12.4 53
1.2
2.5
OCTACUT0503AR
50
38.3
24.5
50
22
20
10.4 41
6.3
0.5
OCTACUT0634AR
63
51.4
37.6
50
22
20
11
10.4 44
6.3
0.7
OCTACUT0805AR
80
68.4
54.7
50
27
23
13
12.4 53
1.2
OCTACUT1006AR
100
88.5
74.7
50
32
32
45
14.4 70
1.6
OCTACUT1257BR
125 113.5
99.8
50
40
32
56
16.4 80
1.8
OCTACUT1608CR
160 148.5 134.8
50
40
29
88.7 16.4 120
3.6
8.4 33
* WT : Tool Weight
SPARE PARTS
Tool Holder Number
CS350990T
Wrench
TKY10F
Wrench
Set Bolt
Set Bolt
HDS08030
BOES101
CS501290T
TKY25T
BOES101
Insert
HDS10031
MILLING
Clamp Screw
OCTACUT0403ARB
OCTACUT0504ARB
OCTACUT0634ARB
OCTACUT0805ARB
OCTACUT0503AR
OCTACUT0634AR
OCTACUT0805AR
OCTACUT1608CR
zOEMX12T3pppp
xREMX12T3pppp
zOEMX1705pppp
xREMX1705pppp
* Clamp Torque (N m) : CS350990T=2.5, CS501290T=7.5
Drilling
Face Milling
Maximum
cutting depth is
4mm
with the inside cutting edge.
4mm
Approx.1.2
1.2
Pocket Milling
4 42
999
444
0.1
Approx.0.1
(Wall ()
Face Geometry)
Deep Shoulder Milling
L096
Core
Chamfer Milling
2DCX
Contouring
2DCX
R Corner Milling
Max.
Depth of Cut
()
(Max.)
C5
Minimum Width to
Eliminate Core
DCX
DCX
Core
42
(Max.)
5
DCX
42
(Max.)
4
APPLICATION
3mm (Max.)
(Chamfer Milling)
(Boring)
(Helical Milling)
(Contour Milling)
(Ramping)
(Drilling)
E
4mm (Max.)
C
(Face Milling)
4 Corners
Usable
9mm (Max.)
B
(Face Milling)
8 Corners
Usable
(Shoulder Milling)
42
Work Material
Hardness
P
Mild Steel
Grade
F7030
240 (180 300)
VP15TF
180 (100 250)
F7030
200 (140 240)
VP15TF
180 (100 250)
F7030
150 (100 170)
VP15TF
120 (80 160)
F7030
130 (90 160)
VP15TF
120 (80 160)
F7030
150 (100170)
VP15TF
120 (80160)
F7030
200 (140 240)
VP15TF
150 (100 200)
VP15TF
160 (100 220)
MB730
1500 (1000 3000)
< 180HB
180 280HB
Carbon Steel
Alloy Steel
280 380HB
Pre-Hardened Steel
High Alloy Steel
35 45HRC
< 300HB
M
Stainless Steel
< 270HB
K
Gray Cast Iron
Tensile Strength
< 350MPa
Ductile Cast Iron
Tensile Strength
360 500MPa
VP15TF
160 (100 220)
Ductile Cast Iron
Tensile Strength
500 800MPa
VP15TF
140 (90190)
Hardened Steel
45 60HRC
VP15TF
80 (50100)
MB730
150 (100 200)
Cutting Mode
Feed per Tooth

(mm/t.)
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
0.2 (0.15 0.25)

0.2 (0.15 0.25)
0.2 (0.15 0.25)
0.075 (0.05 0.1)
0.2 (0.150.25)
0.2 (0.150.25)
0.2 (0.150.25)
0.075 (0.050.1)
0.2 (0.15 0.25)
0.2 (0.15 0.25)
0.2 (0.15 0.25)
0.075 (0.050.1)
0.15 (0.1 0.2)
0.15 (0.1 0.2)
0.1 (0.05 0.15)
0.05 (0.0250.075)
0.15 (0.1 0.2)
0.15 (0.1 0.2)
0.1 (0.05 0.15)
0.05 (0.025 0.075)
0.15 (0.1 0.2)
0.15 (0.1 0.2)
0.1 (0.05 0.15)
0.075 (0.05 0.1)
0.3 (0.25 0.35)
0.25 (0.2 0.3)
0.15 (0.1 0.2)
0.075 (0.05 0.1)
B (D.O.C 0.1 0.5mm)
0.15 (0.1 0.2)
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
A
B
C,E,F
D,G,H,I
0.25 (0.2 0.3)

0.2 (0.15 0.25)
0.1 (0.05 0.15)
0.05 (0.025 0.075)
0.25 (0.2 0.3)
0.2 (0.15 0.25)
0.1 (0.05 0.15)
0.05 (0.025 0.075)
0.15 (0.1 0.2)
0.15 (0.1 0.2)
0.1 (0.05 0.12)
0.05 (0.025 0.06)
B (D.O.C 0.1 0.3mm)
0.15 (0.10.2)
MILLING
This list of recommended cutting conditions is for cutters with diameter < & 80. For cutters with diameter > &80 increase cutting speed by 10%.

a Table Feed (mm/min)=Feed per Tooth x Number of Teeth x Cutter Revolution
-1)
(Note 1) This list of recommended cutting conditions is for flank wear of 0.3mm in 30 min. cutting time.
(Note 2) More than 50mm shank length should be clamped in the milling chuck.
(Note 3) Use step cutting when driling (0.5 mm steps are recommended).
(Note 4) When chattering occurs, reduce cutting speed by 20 30 %.
(Note 5) When using round inserts, make sure that the flat portion of the flank surface is secure against the insert seat wall.
SPARE PARTS
TECHNICAL DATA
P001
Q001
L097
INDEXABLE MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
Roughing
ARX
M
Stainless Steel
Cast Iron
DCON
P
Steel
DCX
DC
Fig.1
RE
Hardened Steel
LH
LF
DCON
DC
DCX
Fig.2 (Center Cutting Edge Type)
LH
RE
DCX
DC
M-class insert.
RE
LF
coolant holes.
DCX
DCON
DC
LF
LH
Type (Fig.)
Clamp Screw Wrench
2.5
10
10
120
20
TPS20
3.0
12
10
120
20
TPS22S TIP07FS RDMW0620M0E
3.5
14
12
140
20
TPS22
TIP07FS RDMW0724M0E
2.5
12
10
120
20
TPS20
TIP06F
RDMW0517M0E
2.5
16
16
11
180
20
TPS20
TIP06F
RDMW0517M0E
ARX30R163SA16S
3.0
16
16
10
180
20
TPS22
TIP07FS RDMW0620M0E
ARX25R173SA16S
2.5
17
16
12
180
20
TPS20
TIP06F
ARX30R173SA16S
3.0
17
16
11
180
20
TPS22
TIP07FS RDMW0620M0E
ARX25R204SA20S
2.5
20
20
15
180
20
TPS20
TIP06F
ARX30R203SA20S
3.0
20
20
14
180
20
TPS22
TIP07FS RDMW0620M0E
ARX25R224SA20S
2.5
22
20
17
180
20
TPS20
TIP06F
ARX30R224SA20S
3.0
22
20
16
180
20
TPS22
TIP07FS RDMW0620M0E
ARX25R255SA20S
2.5
25
20
20
180
20
TPS20
TIP06F
ARX30R254SA20S
3.0
25
20
19
180
20
TPS22
TIP07FS RDMW0620M0E
Order Number
Stock
Number of Teeth
RE
Type
Center Cutting
Non-center Cutting (Multi-tooth)
MILLING
LH
Coolant Hole
y STEEL SHANK TYPE
DCON
a 15 positive, high tolerance
LF
Fig.3 (Non-center Cutting Edge Type (Multi-tooth))
ARX25R102SA10S
ARX30R122SA10S
ARX35R142SA12S
ARX25R122SA10S
ARX25R163SA16S
Dimensions (mm)
TIP06F
Insert
RDMW0517M0E
RDMW0517M0E
RDMW0517M0E
RDMW0517M0E
RDMW0517M0E
Clamp Torque (N m) : TPS20=0.6, TPS22S=0.6, TPS22=0.6
INSERTS
Shape
Order Number
MP8010
VP15TF
Coated Dimensions (mm)
RDMW0517M0E
RDMW0620M0E
RDMW0724M0E
IC
a a
5.0
1.70
a a
6.0
1.99
a a
7.0
2.38
Geometry
15
IC 0.025
L098
S 0.025
DCON
DC
DCX
Fig.1
15
RE
LH
LF
DCON
DC
DCX
Fig.2
15
RE
LH
LF
DCON
DC
DCX
Fig.3
15
RE
LH
LF
RE
DCX
DCON
DC
LF
LH
Type (Fig.)
Number of Teeth
Stock
Order Number
Coolant Hole
Non-center Cutting
(Multi-tooth)
Center
Cutting
Type
y CARBIDE SHANK TYPE
Clamp Screw Wrench
2.5
10
10
150
40
TPS20
3.0
12
10
150
40
TPS22S TIP07FS RDMW0620M0E
3.5
14
12
170
40
TPS22
TIP07FS RDMW0724M0E
2.5
12
10
150
40
TPS20
TIP06F
ARX25R102SA10LW
ARX30R122SA10LW
ARX35R142SA12LW
ARX25R122SA10LW
Dimensions (mm)
TIP06F
Insert
RDMW0517M0E
RDMW0517M0E
* Clamp Torque (N m) : TPS20=0.6, TPS22S=0.6, TPS22=0.6

A
BD
DC
DCON
CRKS
A
L11
LF
OAL
A-A section
y SCREW-IN TYPE
Number of Teeth
RE
DC DCON BD
2.5
16
8.5
14.7
48
2.5
17
8.5
14.5
48
2.5
20
10.5
18.6
2.5
22
10.5
18.5
ARX25R255M12A35
2.5
25
12.5
ARX30R163M08A30
3.0
16
8.5
ARX30R173M08A30
3.0
17
8.5
14.5
48
30
ARX30R203M10A30
3.0
20
10.5
18.5
49
30
ARX30R224M10A30
3.0
22
10.5
18.5
49
30
ARX30R254M12A35
3.0
25
12.5
23.4
57
35
Order Number
Stock
Coolant Hole
ARX25R163M08A30
ARX25R173M08A30
ARX25R204M10A30
ARX25R224M10A30
*2
Dimensions (mm)
MILLING
RE
WT
(kg)
OAL LF
L11
CRKS
30
10
M8
0.1
TPS20
TIP06F
RDMW0517M0E
30
10
M8
0.1
TPS20
TIP06F
RDMW0517M0E
49
30
14
M10 0.2
TPS20
TIP06F
RDMW0517M0E
49
30
14
M10 0.2
TPS20
TIP06F
RDMW0517M0E
23.6
57
35
19
M12 0.2
TPS20
TIP06F
RDMW0517M0E
14.6
48
30
10
M8
0.1
TPS22
TIP07FS RDMW0620M0E
10
M8
0.1
TPS22
TIP07FS RDMW0620M0E
14
M10 0.2
TPS22
TIP07FS RDMW0620M0E
14
M10 0.2
TPS22
TIP07FS RDMW0620M0E
19
M12 0.2
TPS22
TIP07FS RDMW0620M0E
Clamp Screw Wrench
Insert

2 WT : Tool Weight
*
*
SCREW-IN ARBORS
SPARE PARTS
TECHNICAL DATA
L145
P001
Q001
L099
INDEXABLE MILLING
cutting conditions below are a guide only.Please make adjustments according to the machining conditions.
* The
note the follows when machining the hardened steel by using MP8010.
* Please
Please shorten the overhang length as much as possible.
Use with carbide shank recommended.
Please note the setting of the depth of cut especially to prevent the fracture.
The first recommended grade when machining hardened steel of less than 50HRC is VP15TF.
y SHOULDER MILLING POCKET MILLING RAMPING COPYING

Work Material
Hardness
Grade
ARX25RpppSAppS ARX30RpppSAppS
Cutting Speed ARX25RpppMppApp ARX30RpppMppApp ARX35RpppSAppS
vc
(m/min)
ap (mm) fz (mm/t.) ap (mm) fz (mm/t.) ap (mm) fz (mm/t.)
Mild Steel
< 180HB
VP15TF 180 (150 220)
< 1.0
< 0.5
< 1.2
< 0.5
< 1.5
< 0.5
180 350HB
VP15TF 160 (120 200)
< 0.7
< 0.3
< 0.9
< 0.3
< 1.2
< 0.3
Stainless Steel
< 270HB
VP15TF 150 (120 180)
< 0.7
< 0.3
< 0.9
< 0.3
< 1.2
< 0.3
Gray Cast Iron
Tensile Strength < 350MPa
VP15TF 180 (150 220)
< 1.0
< 0.5
< 1.2
< 0.5
< 1.5
< 0.5
Ductile Cast Iron
VP15TF
120 (80 160)
< 1.0
< 0.5
< 1.2
< 0.5
< 1.5
< 0.5
<50HRC
VP15TF
80 (50 120)
< 0.5
< 0.2
< 0.7
< 0.2
< 1.0
< 0.2
> 50HRC
MP8010
80 (50 120)
< 0.3
< 0.2
< 0.4
< 0.2
< 0.5
< 0.2
Hardened Steel
(Note) For ramping, refer to the maximum capacities on page L101.
y SLOT MILLING
Work Material
P
M
K
H
Hardness
Grade
vc
(m/min)
ap (mm) fz (mm/t.) ap (mm) fz (mm/t.) ap (mm) fz (mm/t.)
< 180HB
VP15TF 180 (150 220)
< 1.0
< 0.4
< 1.2
< 0.4
< 1.5
< 0.4
180 350HB
VP15TF 160 (120 200)
< 0.7
< 0.2
< 0.9
< 0.2
< 1.2
< 0.2
Stainless Steel
< 270HB
VP15TF 150 (120 180)
< 0.7
< 0.2
< 0.9
< 0.2
< 1.2
< 0.2
Gray Cast Iron
VP15TF 180 (150 220)
< 1.0
< 0.4
< 1.2
< 0.4
< 1.5
< 0.4
Ductile Cast Iron
VP15TF
120 (80 160)
< 1.0
< 0.4
< 1.2
< 0.4
< 1.5
< 0.4
<50HRC
VP15TF
80 (50 120)
< 0.5
< 0.1
< 0.7
< 0.1
< 1.0
< 0.1
> 50HRC
MP8010
80 (50 120)
< 0.3
< 0.1
< 0.4
< 0.1
< 0.5
< 0.1
Mild Steel
Hardened Steel
y PLUNGING
ARX25RpppSAppS
MILLING
Work Material
P
M
K
H
Hardness
Grade
ARX30RpppSAppS

vc
Cutting Width Feed per Tooth Cutting Width Feed per Tooth Cutting Width Feed per Tooth
(m/min)
ae (mm) fz (mm/t.) ae (mm) fz (mm/t.) ae (mm) fz (mm/t.)
< 180HB
VP15TF 180 (150 220)
< 2.5
< 0.3
< 3.0
< 0.3
< 3.5
< 0.3
180 350HB
VP15TF 160 (120 200)
< 2.5
< 0.2
< 3.0
< 0.2
< 3.5
< 0.2
Stainless Steel
< 270HB
VP15TF 150 (120 180)
< 2.5
< 0.2
< 3.0
< 0.2
< 3.5
< 0.2
Gray Cast Iron
VP15TF 180 (150 220)
< 2.5
< 0.3
< 3.0
< 0.3
< 3.5
< 0.3
Ductile Cast Iron
VP15TF
120 (80 160)
< 2.5
< 0.3
< 3.0
< 0.3
< 3.5
< 0.3
<50HRC
VP15TF
80 (50 120)
< 2.5
< 0.1
< 3.0
< 0.1
< 3.5
< 0.1
> 50HRC
MP8010
80 (50 120)
< 2.5
< 0.1
< 3.0
< 0.1
< 3.5
< 0.1
Mild Steel
Hardened Steel
y HELICAL DRILLING
pppSAppS
ARX25RpppMppApp ARX30RpppMppApp ARX35R
Work Material
Hardness
Grade
Cutting Speed
vc
DOC/pass Feed per Tooth DOC/pass Feed per Tooth DOC/pass Feed per Tooth
(m/min)
ap (mm/pass) fz (mm/t.) ap (mm/pass) fz (mm/t.) ap (mm/pass) fz (mm/t.)
Mild Steel
< 180HB
VP15TF 180 (150 220)
< 1.0
< 0.3
< 1.0
< 0.3
< 1.0
< 0.3
180 350HB
VP15TF 160 (120 200)
< 0.7
< 0.2
< 0.9
< 0.2
< 1.0
< 0.2
Stainless Steel
< 270HB
VP15TF 150 (120 180)
< 0.7
< 0.2
< 0.9
< 0.2
< 1.0
< 0.2
Gray Cast Iron
VP15TF 180 (150 220)
< 1.0
< 0.3
< 1.0
< 0.3
< 1.0
< 0.3
Ductile Cast Iron
VP15TF
120 (80 160)
< 1.0
< 0.3
< 1.0
< 0.3
< 1.0
< 0.3
<50HRC
VP15TF
80 (50 120)
< 0.5
< 0.1
< 0.7
< 0.1
< 1.0
< 0.1
> 50HRC
MP8010
80 (50 120)
< 0.3
< 0.1
< 0.4
< 0.1
< 0.5
< 0.1
Hardened Steel
(Note) For helical drilling, refer to the maximum capacities on page L101.
L100
CUTTING MODE MAXIMUM CAPACITIES

y RAMPING
y HELICAL DRILLING
a How to derive a locus of the center of the tool.
Finding a cutters distance

moved L when depth of
cut reaches ap at a
ramping angle of %.
DC
Cutting edge
diameter
conditions for helical drilling on L100.
ap
RMPX
Tool Corner
Number
Diameter
DC
RE of Teeth
dc
DH
a Set the machine spindle revolution so that the
tool is rotating and cutting in a down cut direction.
Ramping
RMPX
Helical Drilling
2 Distance L at Depth Min. Hole Diameter Max. Hole Diameter

APMX (mm)
of Cut of ap L (mm) DH min. (mm) DH max. (mm)
(mm)
(mm)
ARX25R102SA10S
10
2.5
90
2.5
15
19
ARX25R102SA10LW
10
2.5
90
2.5
15
19
ARX30R122SA10S
12
3.0
90
3.0
18
23
ARX30R122SA10LW
12
3.0
90
3.0
18
23
ARX35R142SA12S
14
3.5
90
3.5
21
27
ARX35R142SA12LW
14
3.5
90
3.5
21
27
ARX25R122SA10S
12
2.5
27.17
2.5
4.87
19
23
ARX25R122SA10LW
12
2.5
27.17
2.5
4.87
19
23
ARX25R163M08A30
16
2.5
13.70
2.5
10.76
27
31
ARX25R163SA16S
16
2.5
13.70
2.5
10.26
27
31
ARX30R163M08A30
16
3.0
21.25
3.0
7.71
26
31
ARX30R163SA16S
16
3.0
21.25
3.0
7.71
26
31
ARX25R173M08A30
17
2.5
12.22
2.5
11.54
29
33
ARX25R173SA16S
17
2.5
12.22
2.5
11.54
29
33
ARX30R173M08A30
17
3.0
18.42
3.0
9.01
28
33
ARX30R173SA16S
17
3.0
18.42
3.0
9.01
28
33
ARX30R203M10A30
20
3.0
13.21
3.0
12.78
34
39
ARX30R203SA20S
20
3.0
13.21
3.0
12.78
34
39
ARX25R204M10A30
20
2.5
9.23
2.5
15.38
35
39
ARX25R204SA20S
20
2.5
9.23
2.5
15.38
35
39
ARX25R224M10A30
22
2.5
7.94
2.5
17.92
39
43
ARX25R224SA20S
22
2.5
7.94
2.5
17.92
39
43
ARX30R224M10A30
22
3.0
11.13
3.0
15.25
38
43
ARX30R224SA20S
22
3.0
11.13
3.0
15.25
38
43
ARX30R254M12A35
25
3.0
9.01
3.0
18.92
44
49
ARX30R254SA20S
25
3.0
9.01
3.0
18.92
44
49
ARX25R255M12A35
25
2.5
6.57
2.5
21.71
45
49
ARX25R255SA20S
25
2.5
6.57
2.5
21.71
45
49
MILLING
Type
Center Cutting
Non-center Cutting (Multi-tooth)
*
*
Locus of the
Desired hole
center of the tool diameter
a For the depth of cut per cycle, refer to the cutting
L=ap/tan % (mm)
Order Number
dc = DH - DC
Cutting
Direction
1 RMPX : Max.Ramping Angle

2 APMX : Max. Depth of Cut
SPARE PARTS
TECHNICAL DATA
P001
Q001
L101
INDEXABLE MILLING
MULTI FUNCTIONAL
MILLING
Including
Flat faces
Roughing
BRP
K
Cast Iron
DCON
M
Stainless Steel
DCX
DC
P
Steel
AZ
RE=(APMX)
When the value of B2 is "-".
*(B2
Corresponding
APMX
Inclination Angle)
LH
LF
a Round shape insert with a
*Please allow for an inclination angle of B2+1
strong cutting edge.

a Wide range of tools available.
a Suitable for mould machining.
4
L
EL
MILLING
5
L
EL
DCX
DC
LF DCON
LH
AZ
B2
12
3.8
85
12
25
0.2
300
CS250560T TKY08F
16
7.8
85
16
25
1.0
300
CS250560T TKY08F
BRP4NR202S20
20
11.8
100
20
30
2.0
225
CS250560T TKY08F
BRP4NR253S25
25
16.8
115
25
35
2.0
202
CS250560T TKY08F
BRP4NR121LS12
12
3.8
150
12
70
0.2
057
CS250560T TKY08F
BRP4NR161LS16
16
7.8
150
16
70
1.0
057
CS250560T TKY08F xRPMT08T2M0E-JS
BRP4NR202LS20
20
11.8
180
20
100
2.0
039
CS250560T TKY08F
BRP4NR253LS25
25
16.8
180
25
100
2.0
039
CS250560T TKY08F
BRP4NR202ELS20
20
11.8
250
20
130
2.0
030
CS250560T TKY08F
BRP4NR253ELS25
25
16.8
250
25
130
2.0
030
CS250560T TKY08F
BRP5NR161S16
16
5.8
85
16
25
0.3
309
CS350760T TKY15F
BRP5NR201S20
20
9.8
100
20
30
1.2
231
CS350760T TKY15F
BRP5NR252S25
25
14.8
115
25
35
2.5
206
CS350860T TKY15F
BRP5NR323S32
32
21.8
125
32
45
2.5
134
CS350860T TKY15F
BRP5NR161LS16
16
5.8
150
16
70
0.3
058
CS350760T TKY15F
BRP5NR201LS20
20
9.8
180
20
100
1.2
040
CS350760T TKY15F
BRP5NR252LS25
25
14.8
180
25
100
2.5
040
CS350860T TKY15F
BRP5NR323LS32
32
21.8
200
32
120
2.5
033
CS350860T TKY15F
BRP5NR252ELS25
25
14.8
250
25
130
2.5
030
CS350860T TKY15F
BRP5NR323ELS32
32
21.8
300
32
180
2.5
022
CS350860T TKY15F
Order Number
Stock
Number of Teeth
Type
Cutting Edge R (APMX)
y SHANK TYPE
BRP4NR121S12
BRP4NR161S16
Dimensions (mm)
(Note) R : regular type L : long type EL : extra long type

Clamp Torque (N m) : CS250560T=1.0, CS350760T=3.5, CS350860T=3.5
L102
APMX Clamp Screw Wrench
Insert
zRPMW08T2M0p
zRPMW10T3M0p
xRPMT10T3M0E-JS
32
19.8
125
40
27.9
BRP6PR504S32
50
BRP6PR504S42
BRP6PR322LS32
BRP6PR403LS32
Stock
Number of Teeth
Type
32
45
137
TS43
TKY15D
125
32
45
TS43
TKY15D
37.8
150
32
50
TS43
TKY15D
50
37.8
150
42
50
TS43
TKY15D
32
19.8
200
32
120
033
TS43
TKY15D
40
27.9
200
32
120
TS43
TKY15D zRPMW1204M0p
BRP6PR504LS32
50
37.8
250
32
150
TS43
TKY15D JS
BRP6PR504LS42
50
37.8
250
42
150
TS43
TKY15D
BRP6PR322ELS32
32
19.8
300
32
50
126
TS43
TKY15D
BRP6PR403ELS32
40
27.9
300
32
50
TS43
TKY15D
BRP6PR403ELS42
40
27.9
300
42
50
244
TS43
TKY15D
BRP6PR504ELS42
50
37.8
300
42
50
TS43
TKY15D
BRP8PR402S32
40
23.8
125
32
45
5.5
TS54
TKY25D
BRP8PR503S32
50
33.8
150
32
50
5.5
TS54
TKY25D
R BRP8PR503S42
50
33.8
150
42
50
5.5
TS54
TKY25D
BRP8PR634S32
63
46.8
150
32
50
5.5
TS54
TKY25D
BRP8PR634S42
63
46.8
150
42
50
5.5
TS54
TKY25D
BRP8PR402LS32
40
23.8
200
32
120
5.5
TS54
TKY25D
BRP8PR503LS32
50
33.8
250
32
150
5.5
TS54
TKY25D zRPMW1606M0p
BRP8PR503LS42
50
33.8
250
42
150
5.5
TS54
TKY25D JS
BRP8PR634LS32
63
46.8
250
32
150
5.5
TS54
TKY25D
BRP8PR634LS42
63
46.8
250
42
150
5.5
TS54
TKY25D
BRP8PR402ELS32
40
23.8
300
32
50
5.5
TS54
TKY25D
BRP8PR402ELS42
40
23.8
300
42
50
5.5
252
TS54
TKY25D
BRP8PR503ELS42
50
33.8
300
42
50
5.5
TS54
TKY25D
BRP8PR634ELS42
63
46.8
300
42
50
5.5
TS54
TKY25D
EL
BRP6PR322S32
BRP6PR403S32
LF DCON
B2
APMX Clamp Screw Wrench
AZ
EL
DC
LH
DCX
Order Number
Dimensions (mm)
Insert
xRPMT1204M0E-
xRPMT1606M0E-
MILLING
(Note) R : regular type L : long type EL : extra long type

SPARE PARTS
TECHNICAL DATA
P001
Q001
L103
BD
DCON
KWW
CBDP
APMX
AZ
DCCB
DC
DCX
LF
Fig.3
100
L8
DAH
DC
DCX
LF
DC
DCX
Set an attached
bolt.
BD
DCON
KWW
LF
L8
CBDP
APMX
Set Bolt
(Attached)
Fig.2
50
63
80
L8
CBDP
DCON
AZ
BD
KWW
AZ
Fig.1
40
APMX
INDEXABLE MILLING
DC
BD
LF
DCON CBDP DAH DCCB KWW
L8
40
27.9
33.3
40
16
18
8.4
5.6
0.4
50
37.8
43.1
50
22
20
11
10.4
6.3
0.5
BRP6PR05004B
50
37.8
43.1
63
22.225
29
11
8.4
BRP6P-063A05R
63
50.8
56.1
50
22
20
11
10.4
BRP6PR06305B
63
50.8
56.1
63
22.225
29
11
BRP6PR08006C
80
67.8
72.8
50
25.4
26
13
BRP8P-063A04R
63
46.8
54.5
50
22
20
BRP8PR06304B
63
46.8
54.5
63
22.225
BRP8PR08005C
80
63.8
70.9
50
BRP8PR10006D
100
83.8
90.6
50
BRP6P-040A03R
BRP6P-050A04R
Dimensions (mm)
WT
(kg)
Max.
Depth of Cut
(mm)
AZ
Type (Fig.)
Number of Teeth
DCX
Order Number
GAMP :-7 +5
GAMF :-15 0
Stock
y ARBOR TYPE
APMX
0.5
6.3
0.7
8.4
0.7
9.5
1.2
11
10.4
6.3
0.7
5.5
29
11
8.4
0.7
5.5
25.4
26
13
9.5
1.2
5.5
31.75
32
45
12.7
1.6
5.5
WT : Tool Weight
SPARE PARTS
Clamp Screw
Wrench
Set Bolt
BRP6P-040A03R
BRP6P-050A04R
TS43
TKY15D
HDS08030
MILLING
Tool Holder Number
TS43
TKY15D
TS54
TKY25D
Insert
zRPMW1204M0p
xRPMT1204M0E-JS
BRP6P-R08006C
BRP8P
L104
zRPMW1606M0p
xRPMT1606M0E-JS
INSERTS
Steel

: Stable Cutting
: General Cutting
Stainless Steel
Honing :
Hardened Steel
NX4545
RPMW08T2M0T
RPMW10T3M0E
RPMW10T3M0T
RPMW1204M0E
RPMW1204M0T
RPMW1606M0E
RPMW1606M0T
RPMT08T2M0E-JS
RPMT10T3M0E-JS
RPMT1204M0E-JS
RPMT1606M0E-JS
Cermet Carbide
Class
Honing
F7030
VP15TF
Order Number
M T
M E
a
a
M T
M E
a
a
M T
M E
M T
M E
M E
a a
M E
M E
a a
a
a
a a
a a
Dimensions (mm)
IC
8
10
2.78
3.97
10
3.97
12
4.76
12
4.76
16
16
6.35
6.35
8
10
2.78
3.97
12
16
4.76
6.35
Geometry
11
IC
11
IC
MILLING
Coated
Shape
: Unstable Cutting
Cast Iron
UTi20T
Work
Material
P
M
K
S
H
SPARE PARTS
TECHNICAL DATA
P001
Q001
L105
INDEXABLE MILLING
y CUTTING SPEED (m/min)
Work Material
Coated
Hardness
Carbide
F7030
VP15TF
UTi20T
< 180HB
250 (200 300)
250 (200 300)
150 (100 200)
180 280HB
180 (130 220)
180 (130 220)
140 (100 170)
280 380HB
160 (110 190)
160 (110 190)
100 (70 120)
Pre-Hardened Steel
35 45HRC
120 (80 140)
120 (80 140)
90 (60 100)
High Alloy Steel
300HB
130 (90 160)
130 (90 160)
100 (70 120)
Stainless Steel
< 260HB
180 (130 220)
180 (130 220)
140 (100 170)
Gray Cast Iron
170 (130 220)
140 (100 170)
Tensile Strength 360 500MPa
140 (100 180)
120 (80 140)
110 (80 140)
90 (70 110)
45 60HRC
60 (50 100)
60 (40 70)
Mild Steel
Carbon Steel
Alloy Steel
Tensile Strength
Ductile Cast Iron
Hardened Steel
< 350MPa
(Note) Cutting speeds shown in bold type are for the recommended first choice grades.
y FEED PER TOOTH (mm/t.)

Depth of Cut (mm)
Type
BRP4
0.40
0.30
0.20
0.10
BRP5
0.40
0.35
0.30
0.20
0.10
BRP6
0.50
0.40
0.30
0.25
0.23
0.20
BRP8
0.60
0.50
0.45
0.40
0.33
0.30
0.25
0.20
RAMPING
y RAMPING ANGLE AND
Cutting
Direction
L=
d
(mm)
tan %
MILLING
MACHINING LENGTH
Formula to find cutting length L

at maximum ramping angle.
Type
BRP4
BRP5
BRP6
BRP8
Cutting Edge Diameter Max. Ramping Angle

(&)
RMPX
12
16
20
25
16
20
25
32
32
40
50
63
80
40
50
63
80
100
5.02
12.2
14.52
8.8
4.52
11.4
14.4
8.37
15.91
10.29
7.12
5.08
3.69
18.86
11.91
8.01
5.60
4.13
* L value is approximate rounded value.

L106
tan %
0.088
0.216
0.259
0.155
0.079
0.202
0.257
0.147
0.285
0.181
0.125
0.089
0.064
0.342
0.211
0.141
0.098
0.072
Cutting Length L at Max. Ramping Angle L(mm)
d=2mm
d=4mm
d=5mm
d=6mm (max.)
d=8mm (max.)
22
9
7
12
25
9
7
13
7
11
16
22
31
5
9
14
20
27
45
18
15
25
50
19
15
27
14
22
32
44
62
11
18
28
40
55
63
24
19
33
17
27
40
56
77
14
23
35
50
69
21
33
48
67
93
17
28
42
61
83
23
37
56
81
110
HELICAL DRILLING
y RELATIONSHIP BETWEEN HOLE DIAMETER AND DEPTH OF CUT
Minimum Hole Diameter
Maximum Hole Diameter
DH max.
DH min.
RMPX
1.0
RMPX
DC
(mm)
DC
BRP8
BRP6
BRP5
BRP4
*1
*2
DC
Ramping Angle RMPX
DH
min.
dc
12
16
16
24
4.55
9.10
20
32
12
3.04
6.08
25
42
17
2.15
4.29
16
22
20
30
10
3.64
7.26
9.10
25
40
15
2.43
4.85
6.08
32
54
22
1.66
3.31
32
52
20
1.82
40
68
28
50
88
63
d=2mm
d=4mm
d=5mm
*1
*2
DH
max.
dc
22
d=6mm
d=8mm
Ramping Angle RMPX

d=2mm
d=4mm
d=5mm
d=6mm
d=8mm
10
3.64
30
14
2.60
5.20
38
18
2.03
4.05
48
23
1.59
3.17
30
14
2.60
5.20
6.50
38
18
2.03
4.05
5.08
48
23
1.59
3.17
3.98
4.15
62
30
1.22
2.43
3.04
3.64
4.55
5.45
62
30
1.22
2.43
3.04
3.64
1.30
2.60
3.25
3.90
78
38
0.96
1.92
2.40
2.88
38
0.96
1.92
2.40
2.88
98
48
0.78
1.52
1.90
2.28
114
51
0.72
1.43
1.79
2.14
124
61
0.60
1.20
1.49
1.79
80
148
68
0.54
1.07
1.34
1.61
158
78
0.47
0.94
1.17
1.40
40
64
24
1.52
3.04
3.79
4.55
6.06
78
38
0.96
1.92
2.40
2.88
3.38
50
84
34
1.07
2.14
2.68
3.22
4.28
98
48
0.76
1.52
1.90
2.28
3.04
63
110
47
0.78
1.55
1.94
2.33
3.10
124
61
0.60
1.20
1.49
1.79
2.39
80
144
64
0.57
1.14
1.42
1.71
2.28
158
78
0.47
0.94
1.17
1.40
1.87
100
184
84
0.43
0.87
1.09
1.30
1.74
198
98
0.37
0.74
0.93
1.12
1.49
d=1mm,RMPX=4.55
d=1mm,RMPX=3.04
MILLING
Type
Cutting
Edge
Diameter
dc
dc
*1 DH=Hole Diameter : & (mm) *2 dc=Tool Pass : & (mm)

BRP4
DH min. (Minimum Hole Diameter)=(DC - 4)2,
BRP5
BRP6
BRP8
dc=(Tool Pass)=DH-D
Note
DH max. (Maximum Hole Diameter)=(DC - 1)2,

d max. (Maximum Depth of Cut)=4(mm)

When machining a hole larger than DH max., first machine a pilot hole smaller than DH max. before enlarging to the required size
as shown above.
Process 1
DH min. DH max.
Process 2
Over DH max.
TECHNICAL DATA
Q001
L107
INDEXABLE MILLING
DEEP SHOULDER
MILLING
Roughing
SPX
M
Stainless Steel
Cast Iron
DC
P
Steel
DCON
a Straight Shank Type (Combination Shank)
APMX
LH
90
OAL
a 7/24 Taper Shank No.50 Type
LF
DC
BT50
APMX
LH
90
OAL
a MT5 shank type
MT5
M20
a Low cutting resistance
DC
due to the use of wavy inserts.

a Suitable for heavy cutting
due to holder rigidity.
APMX
LF
90
OAL
y SHANK TYPE
Stock
Number
of Teeth
SPX4R05016WNES
SPX4R05024WNS
SPX4R05034WNM
Number of Insert
Bottom On-edge A Bottom On-edge B Peripheral
Total
Dimensions (mm)
Flutes
Short Edge Type Coarse Pitch Short Edge Type
Order Number
Coarse Pitch
7/24 Taper Shank (No. 50)
MT5
shank type
MILLING
Straight Shank
(Combination Shank)
Type
DC
OAL DCON
LH
LF
APMX
16
50
180
50.8
100
24
50
220
50.8
140
34
50
270
50.8
SPX4R05044WNL
44
50
320
SPX4R05016BT50NES
16
50
SPX4R05024BT50NS
24
SPX4R05034BT50NM
SPX4R05044BT50NL
SPX4R06324BT50NS
24
SPX4R06334BT50NM
34
SPX4R06344BT50NL
SPX4R06356BT50NX
SPX4R05024MT5NS
JPMX
190412- oo
MPMX
120412- oo
SPMX
120408- oo
72
12
110
20
190
157
30
50.8
240
205
40
249.8
100
148
72
12
50
289.8
140
188
110
20
34
50
339.8
190
238
157
30
44
50
389.8
240
288
205
40
63
289.8
140
188
110
20
63
339.8
190
238
157
30
44
63
389.8
240
288
205
40
56
63
439.8
290
338
261
52
24
50
279.5
150
110
20
SPX4R05034MT5NM
34
50
329.5
200
157
30
SPX4R05044MT5NL
44
50
379.5
250
205
40
SPARE PARTS
*
Tool Holder Number
Clamp
Screw
SPX

a
L108
TS55
Wrench
TKY25D
Anti-seize
Lubricant
MK1KS
Insert
Bottom On-edge A
Bottom On-edge B
Peripheral
JPMX190412-WH
JPMX190412-JM
MPMX120412-WH
MPMX120412-JM
SPMX120408-WH
SPMX120408-JM
CBDP
BD
KWW
DC
DAH
DCON
L8
APMX
LF

Cutter Diameter
DC
Set Bolt
& 63
HSC12070
& 80
16065
Stock
Number
of Teeth
Flutes
Total
y SHELL TYPE
DC LF DCON CBDP DAH BD
SPX4R06324CA058A
24
63 85 25.4
SPX4R08024DA058A
24
80 85 31.75 38 17 76.8
Order Number
Geometry
Number of Insert
Dimensions (mm)
JPMX
KWW L8 APMX 140412- oo
26 13 60
MPMX
120412- oo
SPMX
120408- oo
9.5
58
20
12.7
58
20
(Note) In case of internal coolant supply, please use a face mill arbor with through coolant channels. Regular center-thru or side-thru arbors
can't be used.
CBDP
BD
KWW
DCON
DAH
DC
L8
APMX
LF
Cutter Diameter
DC
Set Bolt
& 63
HSC12070
& 80
16065
Number
of Teeth
Flutes
Total
Number of Insert
Stock
y SHELL TYPE
DC LF DCON CBDP DAH BD KWW L8 APMX 140412- oo
SPX4-063A24A058RA
24
63 85
27
28
13 60
12.4
58
SPX4-080A24A058RA
24
80 85
32
40
17 76.8 14.4
58
Order Number
Geometry
Dimensions (mm)
JPMX
MPMX
120412- oo
SPMX
120408- oo
20
20
MILLING
For metric arbor
(Note) In case of internal coolant supply, please use a face mill arbor with through coolant channels. Regular center-thru or side-thru arbors
can't be used.
SPARE PARTS
*
Tool Holder Number
SPX
Clamp
Screw
Wrench
Anti-seize
Lubricant
TS55
TKY25D
MK1KS
Bottom On-edge A
Insert
Bottom On-edge B
Peripheral
JPMX140412-WH
MPMX120412-WH
SPMX120408-WH
JPMX140412-JM
MPMX120412-JM
SPMX120408-JM
SPARE PARTS
TECHNICAL DATA
P001
Q001
L109
INDEXABLE MILLING
INSERTS
Straight cutting edge type (JM Breaker)

Peripheral
Bottom On-edge B Bottom On-edge A
MILLING
Order Number
L110
W1
IC
RE
a a
19.05
12.7
4.76
1.2
* JPMX140412-WH
a a
14.3
12.7
4.76
1.2
Geometry
RE
W1
JPMX190412-WH
86
MPMX120412-WH
a a
12.7
4.76
11
1.2
RE
86
SPMX120408-WH
a a
12.7
4.76
IC
11
0.8
RE
11
90
JPMX190412-JM
a a
19.05
12.7
4.83
1.2
* JPMX140412-JM
a a
14.3
12.7
4.79
1.2
MPMX120412-JM
IC
RE
86
a a
12.7
4.79
11
1.2
RE
11
86
SPMX120408-JM
a a
* Only for use with a shell type holder.
W1
Shape
Wavy cutting edge type (WH Breaker)

Peripheral
Bottom On-edge B Bottom On-edge A
Type
Dimensions(mm)
Class
VP15TF
VP20RT
Coated
12.7
4.80
IC
0.8
RE
11
90
IC
RECOMMENDED CUTTING CONDITIONS (SHANK TYPE)

y CUTTING CONDITIONS FOR SHOULDER MILLING
WH
< 180HB
Carbon Steel
Alloy Steel
180 350HB
Alloy Tool Steel
< 300HB
Stainless Steel
< 200HB
Gray Cast Iron
Tensile
Strength
Tensile
Strength
< 350HB
WH
JM
WH
JM
WH
JM
VP20RT
Ti Alloy
JM
JM
< 800MPa
WH
WH
< 350MPa
Ductile Cast Iron
JM
VP15TF
Mild Steel
VP20RT
Grade
Breaker
Hardness
VP15TF
Work Material
WH
JM
Cutting Speed
vc
(m/min)
120
(100 140)
120
(100 140)
80
(70 120)
80
(70 120)
80
(60 100)
80
(60 100)
80
(60 100)
80
(60 100)
100
(80 120)
100
(80 120)
80
(60 100)
80
(60 100)
40
(35 50)
40
(35 50)
Cutting Width : ae (mm)

Feed per Tooth : fz (mm/t.)
& 50 (the last letter of order number for cutter body) & 63 (the last letter of order number for cutter body)
S (APMX<110)
<10.0
0.15 0.25
<7.5
0.10 0.20
<10.0
0.15 0.25
<7.5
0.10 0.20
<10.0
0.10 0.20
<7.5
0.10 0.15
<7.5
0.08 0.15
<5.0
0.08 0.15
<10.0
0.15 0.40
<7.5
0.10 0.25
<10.0
0.15 0.35
<7.5
0.10 0.20
<5.0
0.05 0.10
<3.5
0.05 0.10
M (APMX=157)
<5.0
0.15 0.25
<5.0
0.10 0.20
<5.0
0.15 0.25
<5.0
0.10 0.20
<5.0
0.10 0.20
<5.0
0.10 0.15
<5.0
0.08 0.15
<3.5
0.08 0.15
<5.0
0.15 0.35
<5.0
0.10 0.25
<5.0
0.15 0.30
<5.0
0.10 0.20
<3.5
0.05 0.10
<2.5
0.05 0.10
L (APMX=205) S (APMX=110)
<2.5
<12.5
0.10 0.20 0.15 0.25
<2.5
<10.0
0.05 0.15 0.10 0.20
<2.5
<12.5
0.10 0.20 0.15 0.25
<2.5
<10.0
0.05 0.15 0.10 0.20
<2.5
<12.5
0.05 0.15 0.10 0.20
<2.5
<10.0
0.05 0.10 0.10 0.15
<2.5
<10.0
0.05 0.10 0.08 0.15
<2.0
<7.5
0.05 0.10 0.08 0.15
<2.5
<12.5
0.10 0.30 0.15 0.40
<2.5
<10.0
0.05 0.20 0.10 0.25
<2.5
<12.5
0.10 0.25 0.15 0.35
<2.5
<10.0
0.05 0.15 0.10 0.20
<2.0
<7.5
0.05 0.10 0.05 0.10
<1.5
<5.0
0.05 0.10 0.05 0.10
M (APMX=157)
<10.0
0.15 0.25
<7.5
0.10 0.20
<10.0
0.15 0.25
<7.5
0.10 0.20
<10.0
0.10 0.20
<7.5
0.10 0.15
<7.5
0.08 0.15
<5.0
0.08 0.15
<10.0
0.15 0.40
<7.5
0.10 0.25
<10.0
0.15 0.35
<7.5
0.10 0.20
<5.0
0.05 0.10
<3.5
0.05 0.10
L (APMX=205)
<5.0
0.15 0.25
<5.0
0.10 0.20
<5.0
0.15 0.25
<5.0
0.10 0.20
<5.0
0.10 0.20
<5.0
0.10 0.15
<5.0
0.08 0.15
<3.5
0.08 0.15
<5.0
0.15 0.35
<5.0
0.10 0.25
<5.0
0.15 0.30
<5.0
0.10 0.20
<3.5
0.05 0.10
<2.5
0.05 0.10
X (APMX=261)
<2.5
0.10 0.20
<2.5
0.05 0.15
<2.5
0.10 0.20
<2.5
0.05 0.15
<2.5
0.05 0.15
<2.5
0.05 0.10
<2.5
0.05 0.10
<2.0
0.05 0.10
<2.5
0.10 0.30
<2.5
0.05 0.20
<2.5
0.10 0.25
<2.5
0.05 0.15
<2.0
0.05 0.10
<1.5
0.05 0.10
(Note 1) The above cutting conditons are determined based on high rigidity machine and workpiece, where no vibration occurred. Please
adjust processing conditions if the vibration is generated.
(Note 2) If the cutting angle between the tool and workpiece exceeds 90 when machining corners ,Reduce the cutting speed and table feed by
10-20% and ae by 50%. Also if possible, set a radius cutting path for corners.
y SLOT MILLING
Carbon Steel
Alloy Steel
180 350HB
Alloy Tool Steel
< 300HB
Stainless Steel
< 200HB
Gray Cast Iron
Tensile
Strength
< 350MPa
Ductile Cast Iron
Tensile
Strength
JM
JM
< 350HB
WH
JM
WH
JM
WH
JM
VP20RT
Ti Alloy
JM
WH
< 800MPa
WH
WH
JM
Cutting Speed
vc
(m/min)
60
(50 120)
60
(50 120)
60
(50 100)
60
(50 100)
50
(40 80)
50
(40 80)
40
(35 80)
40
(35 80)
50
(40 80)
50
(40 80)
40
(35 80)
40
(35 80)
35
(30 50)
35
(30 50)
Depth of Cut : ap : (mm)

Feed per Tooth : fz (mm/t.)
& 50 (the last letter of order number for cutter body) & 63 (the last letter of order number for cutter body)
S (APMX<110)
<10.0
0.10 0.25
<7.5
0.10 0.15
<10.0
0.10 0.25
<7.5
0.10 0.15
<10.0
0.10 0.25
<7.5
0.10 0.15
<10.0
0.08 0.15
<7.5
0.08 0.15
<10.0
0.15 0.25
<7.5
0.10 0.20
<10.0
0.15 0.25
<7.5
0.10 0.20
<5.0
0.05 0.10
<5.0
0.05 0.10
M (APMX=157)
<5.0
0.10 0.20
<5.0
0.10 0.15
<5.0
0.10 0.20
<5.0
0.10 0.15
<5.0
0.10 0.20
<5.0
0.10 0.15
<5.0
0.08 0.15
<5.0
0.08 0.15
<5.0
0.10 0.25
<5.0
0.10 0.20
<5.0
0.10 0.25
<5.0
0.10 0.20
<3.5
0.05 0.10
<3.5
0.05 0.10
L (APMX=205) S (APMX=110)
<2.5
<12.5
0.10 0.15 0.10 0.25
<2.5
<10.0
0.10 0.15 0.10 0.15
<2.5
<12.5
0.10 0.15 0.10 0.25
<2.5
<10.0
0.10 0.15 0.10 0.15
<2.5
<12.5
0.10 0.15 0.10 0.25
<2.5
<10.0
0.10 0.15 0.10 0.15
<2.5
<12.5
0.05 0.10 0.08 0.15
<2.5
<10.0
0.05 0.10 0.08 0.15
<2.5
<12.5
0.10 0.20 0.15 0.25
<2.5
<10.0
0.10 0.20 0.10 0.20
<2.5
<12.5
0.10 0.20 0.15 0.25
<2.5
<10.0
0.10 0.20 0.10 0.20
<2.0
<7.5
0.05 0.10 0.05 0.10
<2.0
<7.5
0.05 0.10 0.05 0.10
M (APMX=157)
<10.0
0.10 0.25
<7.5
0.10 0.15
<10.0
0.10 0.25
<7.5
0.10 0.15
<10.0
0.10 0.25
<7.5
0.10 0.15
<10.0
0.08 0.15
<7.5
0.08 0.15
<10.0
0.15 0.25
<7.5
0.10 0.20
<10.0
0.15 0.25
<7.5
0.10 0.20
<5.0
0.05 0.10
<5.0
0.05 0.10
L (APMX=205)
<5.0
0.10 0.20
<5.0
0.10 0.15
<5.0
0.10 0.20
<5.0
0.10 0.15
<5.0
0.10 0.20
<5.0
0.10 0.15
<5.0
0.08 0.15
<5.0
0.08 0.15
<5.0
0.10 0.25
<5.0
0.10 0.20
<5.0
0.10 0.25
<5.0
0.10 0.20
<3.5
0.05 0.10
<3.5
0.05 0.10
X (APMX=261)
<2.5
0.10 0.15
<2.5
0.10 0.15
<2.5
0.10 0.15
<2.5
0.10 0.15
<2.5
0.10 0.15
<2.5
0.10 0.15
<2.5
0.05 0.10
<2.5
0.05 0.10
<2.5
0.10 0.20
<2.5
0.10 0.20
<2.5
0.10 0.20
<2.5
0.10 0.20
<2.0
0.05 0.10
<2.0
0.05 0.10
MILLING
< 180HB
VP15TF
Mild Steel
WH
VP20RT
Hardness
VP15TF
Work Material
Grade
Breaker
(Note 2) For slotting, please use high rigidity tools such as SPX4R05016WNES/BT50NES.
SPARE PARTS
TECHNICAL DATA
P001
Q001
L111
INDEXABLE MILLING
RECOMMENDED CUTTING CONDITIONS (SHELL TYPE)

y CUTTING CONDITIONS FOR SHOULDER MILLING
Hardness
Grade
Breaker
Mild Steel
< 180HB
VP15TF
JM
Carbon Steel
Alloy Steel
180 350HB
VP15TF
JM
Alloy Tool Steel
< 300HB
VP15TF
JM
Stainless Steel
< 200HB
VP20RT
JM
Work Material
K
Gray Cast Iron
Ductile Cast Iron
Ti Alloy
Tensile Strength
< 350MPa
Tensile Strength
< 800MPa
< 350HB
VP15TF
WH
VP15TF
JM
VP15TF
WH
VP15TF
JM
VP20RT
JM
Cutting Speed
vc
(m/min)
120
(100 140)
120
(100 140)
120
(80 130)
100
(80 120)
100
(60 110)
80
(60 100)
140
(100 150)
120
(100 140)
120
(80 130)
100
(80 120)
120
(80 130)
100
(80 120)
100
(60 110)
80
(60 110)
100
(60 120)
80
(60 120)
45
(35 50)
40
(35 50)
Depth of Cut
ap
(mm)
Cutting Width
ae
(mm)
Feed per Tooth

fz
(mm/t.)
0.5DC
10
0.15 0.30
0.5DC
10
0.15 0.25
0.5DC
10
0.15 0.30
0.5DC
10
0.15 0.25
0.5DC
10
0.10 0.20
0.5DC
10
0.10 0.15
0.5DC
10
0.10 0.25
0.5DC
10
0.10 0.20
0.5DC
10
0.25 0.40
0.5DC
10
0.25 0.40
0.5DC
10
0.15 0.30
0.5DC
10
0.15 0.25
0.5DC
10
0.20 0.35
0.5DC
10
0.20 0.35
0.5DC
10
0.15 0.30
0.5DC
10
0.15 0.30
0.5DC
10
0.08 0.10
0.5DC
10
0.08 0.10
y SLOT MILLING
MILLING
Work Material
Hardness
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
180 350HB
Alloy Tool Steel
< 300HB
Stainless Steel
< 200HB
K
Gray Cast Iron
Ductile Cast Iron
Ti Alloy
Tensile Strength
< 350MPa
Tensile Strength
< 800MPa
< 350HB
Grade
Breaker
VP15TF
JM
VP15TF
JM
VP15TF
JM
VP20RT
JM
VP15TF
WH
VP15TF
JM
VP15TF
WH
VP15TF
JM
VP20RT
JM
Cutting Speed
vc
Depth of Cut
ap
Cutting Width
ae
Feed per Tooth

fz
120
(100 140)
100
(80 120)
80
(60 100)
100
(80 140)
80
(60 100)
60
(50 100)
80
(60 100)
60
(50 100)
80
(60 100)
60
(50 100)
80
(60 100)
60
(50 100)
40
(35 50)
10
DC
0.15 0.25
0.25DC
DC
0.15 0.25
10
DC
0.10 0.20
10
DC
0.10 0.15
0.25DC
DC
0.10 0.25
0.6DC
DC
0.10 0.20
0.25DC
DC
0.10 0.20
(m/min)
(mm)
(mm)
(mm/t.)
0.6DC
DC
0.10 0.15
0.25DC
DC
0.10 0.25
0.5DC
DC
0.10 0.20
0.25DC
DC
0.10 0.20
0.5DC
DC
0.10 0.15
0.25DC
DC
0.06 0.10
L112
CHAMFER
MILLING
Roughing
CESP,CFSP,CGSP
P
Cast Iron
L16
DCX
DC
KAPR
DC
a Covers 5 cutting modes.

a Excellent sharpness with
DCON
BD
Steel
R0.8
11 positive inserts.
a 30, 45 and 60chamfer series.
L5
APMX
LH
R0.8
L6
LF
APMX
CESPR081S20
30
19.6
110
20
19.5
40
25
11
L6 APMX Clamp
Screw
10.2 TS52
zTKY25R
SPMW1203pp
CESPR161S20
30
16
27.8
110
20
19.5
40
25
11
10.2
TS5
zTKY25R
SPMW1203pp
CESPR323S32
30
32
43.8
125
32
31.5
45
36
14
19
10.2
TS5
zTKY25R
SPMW1203pp
CFSPR041S16S
45
15.7
85
16
14.4
25
24
10
5.9
TS4
xTKY15F
SPMW0903pp
CFSPR041S16L
45
15.7
110
16
14.4
50
24
10
5.9
TS4
xTKY15F
SPMW0903pp
CFSPR081S20
45
24.6
110
20
19.5
40
25
11
8.3
TS5
zTKY25R
SPMW1203pp
CFSPR161S20
45
16
32.6
110
20
19.5
40
25
11
8.3
TS5
zTKY25R
SPMW1203pp
CFSPR323S32
45
32
48.6
125
32
31.5
45
36
14
19
8.3
TS5
zTKY25R
SPMW1203pp
CGSPR081S20
60
28.4
110
20
19.5
40
25
11
5.9
TS5
zTKY25R
SPMW1203pp
CGSPR161S20
60
16
36.4
110
20
19.5
40
25
11
5.9
TS5
zTKY25R
SPMW1203pp
CGSPR323S32
60
32
52.4
125
32
31.5
45
36
14
19
5.9
TS5
zTKY25R
SPMW1203pp
Stock
R
Number of Teeth
Order Number
Dimensions (mm)
z
x
KAPR DC
DCX
LF DCON BD
LH
L16
L5
Wrench
Insert
SPMW090308
SPMW120304
SPMW120308
*a
M E* a
M E* a
M E* a
M E
Dimensions (mm)
IC
RE
a a a a
9.525
3.18
0.4
a a a a
9.525
3.18
0.8
a a a a
12.7
3.18
0.4
a a a a
12.7
3.18
0.8
Geometry
MILLING
SPMW090304
Cermet Carbide
NX2525
NX4545
UTi20T
HTi10
Order Number
Coated
VP15TF
UP20M
Class
Shape
Honing
INSERTS
RE
11
IC
* NX2525 and NX4545 insert honing is "T" type.

Work Material
Hardness
P
Carbon Steel
Alloy Steel
180 280HB
280 350HB
Cast Iron
Tensile Strength
< 450MPa

Chamfer Milling
Face Milling
Grade
Cutting Speed
(m/min)
UTi20T
80 (60 100)
0.4
0.15
UP20M
130 (100 160)
0.4
0.2
NX4545
130 (100 160)
0.4
0.2
UTi20T
80 (60 100)
0.3
0.15
UTi20T
100 (85 120)
0.5
0.25
HTi10
100 (85 120)
0.5
0.25

a
SPARE PARTS
TECHNICAL DATA
P001
Q001
L113
INDEXABLE MILLING
DEEP SHOULDER
MILLING
Roughing
VFX5
K
H
KWW
DAH
DC
BD
DCON
CBDP
L8

a Screw-on type clamping.
a High efficiency milling of
APMX
LF
titanium alloys.
Total
3
3
6
9
40
40
50
60
16
16
21
21
8.5
8.5
38.2
38.2
8.4
8.4
5.6
5.6
26
38
0.3
0.4
50
50
27
23
12.5
48.2
12.4
7.0
26
0.4
50
60
27
23
12.5
48.2
12.4
7.0
38
0.5
50
50
22
21
10.5
48.2
10.4
6.3
26
0.5
12
50
60
22
21
10.5
48.2
10.4
6.3
38
0.6
12
50
60
27
23
12.5
48.2
12.4
7.0
38
0.5
16
50
70
22
21
10.5
48.2
10.4
6.3
50
0.7
10
63
60
27
28
12.5
61
12.4
7.0
26
1.0
5
6
25
36
63
80
85
100
27
32
28
28
12.5
16.5
61
77.3
12.4
14.4
7.0
8.0
63
75
1.4
2.8
Stock
Number of Flutes
y SHELL TYPE
Order Number
VFX5-040A03A026R
VFX5-040A03A038R
VFX5-050X03A026R
VFX5-050X03A038R
VFX5-050A04A026R
VFX5-050A04A038R
VFX5-050X04A038R
VFX5-050A04A050R
VFX5-063A05A026R
VFX5-063A05A063R
VFX5-080A06A075R
Dimensions (mm)
DC
LF
DCON
CBDP
DAH
BD
WT
(kg)
KWW
L8
APMX
* WT : Tool Weight
SPARE PARTS
*2
*3
Number of Insert
Order Number
MILLING
Peripheral 1
cutting edge
XNMU1607
08R-oo
Wrench
Coolant Nozzle Number Anti-seize Lubricant
Set Bolt
XNMU1607
ooR-oo
TS352
W8-S1
TKY10D
HSD04004H08
MK1KS
HSC08040
TS352
W8-S1
TKY10D
HSD04004H08
12
MK1KS
HSC08050
TS352
W12-S1
TKY10D
HSD04004H08
MK1KS
HSC12035
TS352
W12-S1
TKY10D
HSD04004H08
12
MK1KS
HSC12045
TS352
W10-S1
TKY10D
HSD04004H08
12
MK1KS
HSC10035
TS352
12
W10-S1
TKY10D
HSD04004H08
16
MK1KS
HSC10045
TS352
12
W12-S1
TKY10D
HSD04004H08
16
MK1KS
HSC12045
TS352
16
W10-S1
TKY10D
HSD04004H08
20
MK1KS
HSC10055
12
TS352
10
W12-S1
TKY10D
HSD04004H08
15
MK1KS
HSC12045
TS352
25
W12-S1
TKY10D
HSD04004H08
30
MK1KS
HSC12070
20
TS352
36
W16-S1
TKY10D
HSD04004H08
42
MK1KS
HSC16080
30
Clamp Screw Number Seal Washer
VFX5-040A03A026R
VFX5-040A03A038R
VFX5-050X03A026R
VFX5-050X03A038R
VFX5-050A04A026R
VFX5-050A04A038R
VFX5-050X04A038R
VFX5-050A04A050R
VFX5-063A05A026R
VFX5-063A05A063R
VFX5-080A06A075R
End cutting
edge
Only corner radius R0.8 can be used for the peripheral cutting edges.
*21 Clamp
(N m) : TS352=2.5
*3 CoolantTorque
nozzles are available with varying diameters for adjusting coolant pressure. Select nozzles as required by the specification.
*
< 1Mpa
( < 20 l/min.)
Standard
> 5Mpa
( > 30 l/min.)
> 7Mpa
( > 50 l/min.)
Nozzle Dia.
0.6mm
0.8mm
1.2mm
1.6mm
Order Number
HSD04004H06
HSD04004H08
HSD04004H12
HSD04004H16
*
*
*
4 To plug a coolant hole, HSS04004(JIS B 1177 flat point M4x4, clamp torque 1.5N m) is available.
5 Note for insert with a corner radius of 3.2 and above, as corner radius increases the LF dimension increases.
Corner radius 3.2: LF+0.7mm Corner radius 4.0: LF+1.5mm
a
L114
Clamp Torque (N m) : HSD04004Hpp=1.5
INSERTS
RE
16.0 7.0 11.1 6.5

16.0 7.0 11.1 6.5
1.0
1.0
0.8
1.2
16.0 7.0 11.1 6.5
1.0
1.6
16.0 7.0 11.1 6.5
1.0
2.4
a
a
17.3 7.0 11.1 6.5

18.9 7.0 11.1 6.5
3.2
4.0
16.0 7.0 11.1 6.5
1.0
0.8
Geometry
RE
BS
INSL
RE
W1
INSL
BS
W1
W1
Cutting edge
enhancement type
16.0 7.0 11.1 6.5
1.0
0.8
W1
BS
XNMU160708R-LS
INSL
RE
*11
*
XNMU160708R-MS
XNMU160712R-MS
XNMU160716R-MS
XNMU160724R-MS
XNMU160732R-MS
XNMU160740R-MS
XNMU160708R-HS
BS
General purpose
Order Number
Dimensions (mm)
INSL
Shape
MP9030
MP9130
Stock
Coated
Chip processing type
MILLING
for insert with a corner radius of 3.2 and above, as corner radius increases the LF dimension increases.
*1 Note
Corner radius 3.2: LF+0.7mm Corner radius 4.0: LF+1.5mm
SPARE PARTS
TECHNICAL DATA
P001
Q001
L115
INDEXABLE MILLING
y VFX5
Work Material
Cutting Revolution Depth of Cutting Feed per Table Chip Removal Estimated Expected Tool life
Cutting
Cut
Width
Tooth
Feed
Rate
cutting
Torque
ratio
Edge Number of Recommended Speed
power
Diameter Flutes
Insert
Q
ap
ae
fz
vf
vc
n
(mm)
(min-1)
(Nm)
(%)
(mm)
(mm)
(mm/t.) (mm/min) (cm3/min) (kW)
(m/min)
S
&40
&50
Titanium Alloy
(Ti-Al-4V)
&63
&80
&40
&50
Titanium Alloy
(Ti-5Al-5V-5Mo-3Cr)
&63
MILLING
&80
*
*
*
*
L116
LS
40
318
38
40
0.10
95
145
6.5
194
40
MS
50
398
38
24
0.10
119
109
4.5
109
60
MS
60
477
38
16
0.10
143
87
3.5
69
80
HS
60
477
38
0.12
172
52
2.3
45
100
LS
40
255
38
50
0.10
76
145
6.5
242
40
MS
50
318
50
30
0.10
127
191
7.9
237
60
MS
60
382
50
20
0.10
153
153
6.0
151
80
HS
60
382
50
10
0.12
183
92
3.9
98
100
LS
40
202
60
63
0.10
101
382
16.8
793
40
MS
50
253
60
38
0.10
126
286
11.8
447
60
MS
60
303
60
25
0.10
152
229
9.0
285
80
HS
60
303
60
13
0.12
182
138
5.9
185
100
LS
40
159
75
80
0.10
95
573
25.0
1500
40
MS
50
199
75
48
0.10
119
430
17.6
846
60
MS
60
239
75
32
0.10
143
344
13.5
539
80
HS
60
239
75
16
0.12
172
206
8.7
350
100
LS
25
199
38
40
0.08
48
73
3.4
161
30
MS
25
199
38
24
0.08
48
44
1.9
92
50
MS
30
239
38
16
0.10
72
44
1.8
74
70
HS
30
239
38
0.10
72
22
1.0
41
90
LS
25
159
50
50
0.08
51
127
5.8
350
30
MS
25
159
50
30
0.08
51
76
3.4
201
50
MS
30
191
50
20
0.10
76
76
3.2
160
70
HS
30
191
50
10
0.10
76
38
1.8
89
90
LS
25
126
60
63
0.08
51
191
8.7
658
30
MS
25
126
60
38
0.08
51
115
5.0
378
50
MS
30
152
60
25
0.10
76
115
4.8
301
70
HS
30
152
60
13
0.10
76
57
2.6
167
90
LS
25
99
75
80
0.08
48
286
13.0
1246
30
MS
25
99
75
48
0.08
48
172
7.5
716
50
MS
30
119
75
32
0.10
72
172
7.1
570
70
HS
30
119
75
16
0.10
72
86
3.9
316
90
1 Please note that machining performance varies depending to the conditions such as machine rigidity, work clamping rigidity, coolant supply
system, pressure and flow volume etc.
2 Internal coolant is recommended. Please use an FMH type arbor for through coolant. Using external coolant in combination with through
coolant is even more effective.
3 The tool life ratio shows the standard when ae = tool diameter 20% is assumed to be 100 when shoulder cutting.
4 The maximum depth of cut (ap) varies according to the machine rigidity and power.
DEEP SHOULDER
MILLING
<CUTTING FOR TITANIUM ALLOY>
Roughing
VFX6
K
H
KWW
DAH
DC
BD
DCON
CBDP
L8
APMX
LF
a Screw-on type.
a High efficiency milling
titanium alloys.
63
60
27
28
12.5
61
12.4
31
0.9
16
63
85
27
28
12.5
61
12.4
60
1.3
10
80
60
32
28
16.5
77.3
14.4
31
1.5
25
80
100
32
28
16.5
77.3
14.4
75
2.6
12
100
65
40
30
20.5
96.6
16.4
31
2.7
36
100
115
40
30
20.5
96.6
16.4
90
4.8
Order Number
VFX6-063A04A031R
VFX6-063A04A060R
VFX6-080A05A031R
VFX6-080A05A075R
VFX6-100A06A031R
VFX6-100A06A090R
Dimensions (mm)
Total
Stock
R
Number of Flutes
y SHELL TYPE
DC
LF
DCON
CBDP
DAH
WT
(kg)
BD
KWW
L8
APMX
* WT : Tool Weight
SPARE PARTS
*3
Number of Insert
Peripheral 1
cutting edge
Set Bolt
XNMU1909
ooR-oo
XNMU1909
12R-oo
Order Number
Clamp Screw Number Seal Washer
VFX6-063A04A031R
VFX6-063A04A060R
VFX6-080A05A031R
VFX6-080A05A075R
VFX6-100A06A031R
VFX6-100A06A090R
Wrench
Coolant Nozzle Number Anti-seize Lubricant
End cutting
edge
TS450
W12-S1
TKY20T
HSD04004H08
12
MK1KS
HSC12045
TS450
16
W12-S1
TKY20T
HSD04004H08
20
MK1KS
HSC12070
12
TS450
10
W16-S1
TKY20T
HSD04004H08
15
MK1KS
HSC16040
TS450
25
W16-S1
TKY20T
HSD04004H08
30
MK1KS
HSC16080
20
TS450
12
W20-S1
TKY20T
HSD04004H08
18
MK1KS
HSC20040
TS450
36
W20-S1
TKY20T
HSD04004H08
42
MK1KS
HSC20090
30
corner radius R1.2 can be used for the peripheral cutting edges except the end cutting edge.
*12 Only
*3 Coolant nozzles are available with varying diameters for adjusting coolant pressure. Select nozzles as required by the specification.
*
< 1Mpa
( < 20 l/min.)
Standard
> 5Mpa
( > 30 l/min.)
> 7Mpa
( > 50 l/min.)
Nozzle Dia.
0.6mm
0.8mm
1.2mm
1.6mm
Order Number
HSD04004H06
HSD04004H08
HSD04004H12
HSD04004H16
*
*
*
MILLING
*2
Clamp Torque (N m) : HSD04004Hpp=1.5
4 The part number for a blank screw without a through nozzle is HSS04004.
5 Note for insert with a corner radius of 3.2 and above, as corner radius increases the LF dimension increases.
Corner radius 3.2: LF+0.7mm Corner radius 4.0: LF+1.5mm Corner radius 5.0: LF+1.5mm
SPARE PARTS
TECHNICAL DATA
P001
Q001
L117
INDEXABLE MILLING
INSERTS
19.1 9.5 12.7 8.5

19.1 9.5 12.7 8.5
1.0
1.0
1.2
1.6
19.1 9.5 12.7 8.5
1.0
2.4
20.2 9.5 12.7 8.5
3.2
a
a
21.8 9.5 12.7 8.5

21.8 9.5 12.7 8.5
4.0
5.0
19.1 9.5 12.7 8.5
1.0
1.2
Geometry
RE
INSL
RE
19.1 9.5 12.7 8.5
1.0
1.2
W1
BS
XNMU190912R-LS
Chip processing
type
MILLING
for insert with a corner radius of 3.2 and above, as corner radius increases the LF dimension increases.
*1 Note
Corner radius 3.2: LF+0.7mm Corner radius 4.0: LF+1.5mm Corner radius 5.0: LF+1.5mm
L118
INSL
RE
Cutting edge
enhancement type
RE
BS
W1
BS
W1 INSL
W1
*
*
*
XNMU190912R-MS
XNMU190916R-MS
XNMU190924R-MS
1XNMU190932R-MS
1XNMU190940R-MS
1XNMU190950R-MS
XNMU190912R-HS
BS
General
purpose
Order Number
Dimensions (mm)
INSL
Shape
MP9030
MP9130
Stock
Coated

y VFX6
Work Material
Cutting Revolution Depth of Cutting Feed per Table Chip Removal Estimated Expected Tool life
Cutting
Cut
Width
Tooth
Feed
Rate
cutting
Torque
ratio
Edge Number of Recommended Speed
power
Diameter Flutes
Insert
Q
ap
ae
fz
vf
vc
n
(mm)
(min-1)
(Nm)
(%)
(mm)
(mm)
(mm/t.) (mm/min) (cm3/min) (kW)
(m/min)
S
&63
Titanium Alloy
(Ti-Al-4V)
&80
&100
&63
Titanium Alloy
(Ti-5Al-5V-5Mo-3Cr)
&80
&100
LS
40
202
60
63
0.10
81
306
13.4
634
40
MS
50
253
60
38
0.10
101
229
9.5
357
60
MS
60
303
60
25
0.10
121
183
7.2
228
80
HS
60
303
60
13
0.12
146
110
4.7
148
100
LS
40
159
75
80
0.10
80
477
20.8
1250
40
MS
50
199
75
48
0.10
99
358
14.7
705
60
MS
60
239
75
32
0.10
119
286
11.2
449
80
HS
60
239
75
16
0.12
143
172
7.3
291
100
LS
40
127
90
100
0.10
76
688
29.6
2218
40
MS
50
159
90
60
0.10
95
516
20.9
1252
60
MS
60
191
90
40
0.10
115
413
16.0
798
80
HS
60
191
90
20
0.12
138
248
10.3
517
100
LS
25
126
60
63
0.08
40
153
7.0
527
30
MS
25
126
60
38
0.08
40
92
4.0
303
50
MS
30
152
60
25
0.10
61
92
3.8
241
70
HS
30
152
60
13
0.10
61
46
2.1
133
80
LS
25
99
75
80
0.08
40
239
10.8
1038
30
MS
25
99
75
48
0.08
40
143
6.2
597
50
MS
30
119
75
32
0.10
60
143
5.9
475
70
HS
30
119
75
16
0.10
60
72
3.3
263
80
LS
25
80
90
100
0.08
38
344
15.3
1841
30
MS
25
80
90
60
0.08
38
206
8.8
1059
50
MS
30
95
90
40
0.10
57
206
8.4
844
70
HS
30
95
90
20
0.10
57
103
4.7
466
80
note that machining performance varies depending to the conditions such as machine rigidity, work clamping rigidity, coolant supply
*1 Please
system, pressure and flow volume etc.
Internal coolant is recommended. Please use an FMH type arbor for through coolant. Using external coolant in combination with through
*2 coolant
is even more effective.
MILLING
tool life ratio shows the standard when ae = tool diameter 20% is assumed to be 100 when shoulder cutting.
*34 The
The maximum depth of cut (ap) varies according to the machine rigidity and power.
*
L119
INDEXABLE MILLING
BALL NOSE
END MILL
Including
curved faces
Finishing
Cast Iron
Non-ferrous Metal
BD
B5
DC
P
Steel
Fig.1
DCON
SRF, SRB
Hardened Steel
PRFRAD
LU
LH
LF
DC
DCON
BD
Fig.2
B2
LU
PRFRAD
LH
a S-shaped cutting edge provides
LF
BD
Fig.3
DCON
B5
DC
sharpness similar to that of

solid ball nose end mills.
a Highly accurate corner radius tolerance
allows for high precision finishing.
a Carbide shank type available.
PRFRAD
LU
LH
LF
Semi-long
Long
MILLING
Standard
Dimensions (mm)
PRFRAD DC DCON LF
BD
LH
LU
B2
B5
Type (Fig.)
Stock
R
Number of Teeth
Type
y STEEL SHANK TYPE
Order Number
B2
*
Clamp Screw
Wrench
Insert
SRFT10
SRBT10
SRFT12
SRBT12
SRFT16
SRBT16
SRFT20
SRBT20
SRFT25
SRBT25
SRFT30
SRBT30
SRFT32
SRBT32
SRFT10
SRBT10
SRFT12
SRBT12
SRFT16
SRBT16
SRFT20
SRBT20
SRFT20
SRBT20
SRFT25
SRBT25
SRFT25
SRBT25
SRFT30
SRBT30
SRFT20
SRBT20
SRFT20
SRBT20
SRFT25
SRBT25
SRFT25
SRBT25
SRFT30
SRBT30
10
12
110
9.5
40
13
138 130
RS3008T
zTKY08D
SRFH12S16M
12
16
120
11.5
50
15
236 130
RS3510T
zTKY10D
SRFH16S20M
16
20
130
15.5
50
20
244 130
RS4015T
xTKY15T
SRFH20S25M
1 10
20
25
150
19.5
70
24
223 130
RS5020T
xTKY20T
SRFH25S32M
1 12.5
25
32
180
24.5
80
30
258 130
RS6025T
xTKY25T
SRFH30S32M
1 15
30
32
200
29.5
100
35
RS8030T
xTKY30T
SRFH32S32M
1 16
32
32
200
31.5
100
35
RS8030T
xTKY30T
SRFH10S12L
10
12
150
9.5
60
13
130 130
RS3008T
zTKY08D
SRFH12S16L
12
16
160
11.5
70
15
147 130
RS3510T
zTKY10D
SRFH16S20L
16
20
160
15.5
70
20
151 130
RS4015T
xTKY15T
SRFH20S25L
1 10
20
25
180
19.5
80
24
203 130
RS5020T
xTKY20T
SRFH20S20L80
1 10
20
20
180
19.5
80
24
SRFH25S32L
1 12.5
25
32
200
24.5
100
30
SRFH25S25L100
1 12.5
25
25
200
24.5
100
30
SRFH30S32L
1 15
30
32
230
29.5
130
35
SRFH20S25E
1 10
20
25
220
19.5
120
24
SRFH20S20E120
1 10
20
20
220
19.5
120
24
SRFH25S32E
1 12.5
25
32
250
24.5
150
30
SRFH25S25E150
1 12.5
25
25
250
24.5
150
30
SRFH30S32E
1 15
30
32
300
29.5
200
35
L120
SRFH10S12M
RS5020T
xTKY20T
RS6025T
xTKY25T
RS6025T
xTKY25T
RS8030T
xTKY30T
RS5020T
xTKY20T
RS5020T
xTKY20T
RS6025T
xTKY25T
RS6025T
xTKY25T
RS8030T
xTKY30T
217 130
130 130
130 130
(Note) Ensure inserts are fitted in the correct way. (Refer to page L123.)
Clamp Torque (N m) : RS3008T=1.5, RS3510T=2.5, RS4015T=3.3, RS5020T=5.0, RS6025T=7.5, RS8030T=10.0
DC
DCON
BD
Fig.1
PRFRAD
LU
LH
LF
Long
Standard
Type (Fig.)
Stock
Order Number
Number of Teeth
Type

Dimensions (mm)
PRFRAD
DC
DCON
LF
BD
LH
LU
Clamp Screw
Wrench
SRFH10S10MW
10
10
110
9.5
40
13
RS3008T zTKY08D
SRFH12S12MW
12
12
120
11.5
50
15
RS3510T zTKY10D
SRFH16S16MW
16
16
130
15.5
50
20
RS4015T xTKY15T
SRFH20S20MW
10
20
20
180
19.5
80
24
RS5020T xTKY20T
SRFH25S25MW
12.5
25
25
200
24.5
100
30
RS6025T xTKY25T
SRFH30S32MW
RS8030T xTKY30T
SRFH10S10LW
SRFH12S12LW
SRFH16S16LW
SRFH16S16EW
15
30
32
230
29.5
130
35
16
32
32
231
29.5
131
36
10
10
150
9.5
60
13
RS3008T zTKY08D
12
12
160
11.5
70
15
RS3510T zTKY10D
16
16
160
15.5
70
20
RS4015T xTKY15T
16
16
200
15.5
110
20
RS4015T xTKY15T
SRFH20S20LW
10
20
20
250
19.5
150
24
RS5020T xTKY20T
SRFH25S25LW
12.5
25
25
300
24.5
200
30
RS6025T xTKY25T
SRFH30S32LW
RS8030T xTKY30T
15
30
32
350
29.5
250
35
16
32
32
351
29.5
251
36
Insert
SRFT10
SRBT10
SRFT12
SRBT12
SRFT16
SRBT16
SRFT20
SRBT20
SRFT25
SRBT25
SRFT30
SRBT30
SRFT32
SRBT32
SRFT10
SRBT10
SRFT12
SRBT12
SRFT16
SRBT16
SRFT16
SRBT16
SRFT20
SRBT20
SRFT25
SRBT25
SRFT30
SRBT30
SRFT32
SRBT32
(Note 1) SRFH30S32MW and SRFH30S32LW tool body can use both inserts SRFT30 and SRFT32.
However, the overall length size LF is different respectively.
(Note 2) Ensure inserts are fitted in the correct way. (Refer to page L123.)
PRFRAD
LF
L11
OAL
y SCREW-IN TYPE
A-A section
Coolant Hole
Number of Teeth

Stock
Order Number
*2
WT
Dimensions (mm)
*1
(kg)
PRFRAD DC DCON BD
OAL
LF
L11
CRKS
Clamp Screw
Wrench
Insert
SRFT16
SRBT16
SRFT20
SRBT20
SRFT25
SRBT25
SRFT30
SRBT30
SRFT32
SRBT32
SRFH16AM0830
16
8.5 14.9
48
30
10
0.1 RS4015T
TKY15T
SRFH20AM1035
1 10
20
10.5 18.4
54
35
14
10
0.1 RS5020T
TKY20T
SRFH25AM1240
1 12.5
25
12.5 23.5
62
40
19
12
0.1 RS6025T
TKY25T
15
30
17
28.1
68
45
24
16
0.2
16
32
17
28.1
69
46
24
16
0.2
SRFH30AM1645
MILLING
BD
DC
DCON
CRKS
RS8030T
TKY30T
(Note 1) SRFH30AM1645 tool body can use both inserts SRFT30 and SRFT32. However, the overall length size OAL is different respectively.
1 Clamp Torque (N m) : RS4015T=3.3, RS5020T=5.0, RS6025T=7.5, RS8030T=10.0
2 WT : Tool Weight
*
*
SPARE PARTS
TECHNICAL DATA
P001
Q001
L121
INDEXABLE MILLING
INSERTS
Dimensions (mm)
Order Number
SRFT10
DC PRFRAD
BS
a a a
10
8.5 0.5
SRFT12
a a a
12
10
0.5
SRFT16
a a a
16
12
SRFT20
a a a
20
10
15
SRFT25
a a a
25
12.5 18.5 1
SRFT30
a a a
30
15
22.5 1
SRFT32
a a a
32
16
23.5 1
SRBT10
10
SRBT12
12
SRBT16
16
SRBT20
20
10
SRBT25
25
12.5 18.5
SRBT30
30
15
SRBT32
32
16
2.6
10
12
15
22.5
23.5
BS
L0.015
7
0 .02
-0
2.6
PRFRAD0.006
C
D
8.5
Geometry
PRFRAD
DC
Shape
EP6120
VP15TF
MP8010
Coated

Work Material
Mild Steel

(AISI 1045, AISI 4140)

(AISI 4340)
Pre-Hardened Steel
MILLING
(AISI P21, AISI P20 etc)
Alloy Tool Steel
Hardness
Grade
Cutting Speed
vc
(m/min)
Feed per Tooth

fz
(mm/t.)
Depth of Cut
ap
(mm)
180HB
EP6120
200 (80 300)
0.2 (0.1 0.3)
0.05DC
EP6120
200 (80 300)
0.2 (0.1 0.3)
0.05DC
VP15TF
200 (80 300)
0.2 (0.1 0.3)
0.05DC
EP6120
200 (80 300)
0.2 (0.1 0.3)
0.05DC
EP6120
150 (80 200)
0.2 (0.1 0.3)
0.05DC
VP15TF
150 (80 200)
0.2 (0.10.3)
0.05DC
EP6120
150 (80 200)
0.2 (0.1 0.3)
0.05DC
VP15TF
150 (80 200)
0.2 (0.1 0.3)
0.05DC
180280HB
280350HB
35 45HRC
350HB
Gray Cast Iron
Tensile Strength
MP8010
250 (80 450)
0.2 (0.10.3)
0.05DC
Ductile Cast Iron
Tensile Strength
MP8010
200 (80 300)
0.2 (0.1 0.3)
0.05DC
Ductile Cast Iron
Tensile Strength
MP8010
200 (80 300)
0.2 (0.10.3)
0.05DC
EP6120
200 (80 300)
0.2 (0.1 0.3)
0.05DC
(FC300)
(FCD450)
350MPa
450MPa
800MPa
Hardened Steel
45 55HRC
MP8010
100 (60 120)
0.2 (0.10.3)
0.05DC
Hardened Steel
5565HRC
MP8010
80 (60 120)
0.2 (0.1 0.3)
0.01DC
(Note 1) The above values are average condition values at actual cutting speeds. The values change slightly according to the state of a machine
to be used and method of workholding. Adjust the values depending on an actual machine condition, referring to the above values.
(Note 2) For end mills with a carbide shank, you will be able to set about 20 percent higher cutting conditions.
(Note 3) Please note the following when machining hardened steel with MP8010.
a
L122
CUTTING SPEED FORMULAE

1. Employing'
Calculate cutting speed at point P.
(Cutting speed at the cutting depth border for oblique machining)
Formula : Cutting Speed =
DC
) DC sin ' n
(m/min)
1000
DC-2ap
)+90 %
DC
n : Spindle Speed (min-1)
'=cos-1(
ap
Calculate cutting speed at point Q.

2. Employing ap
(Cutting speed at the cutting depth border)
2)n
ap (DC-ap)
(m/min)
1000
n : Spindle Speed (min-1)

DC : Cutting Edge Diameter (mm)
ap : Depth of Cut (mm)
ap
Formula : Cutting Speed =
'
FITTING INSERTS ON HOLDERS

1. Clean the insert seat
Clean the insert seat in the holder body by blowing air or using a brush.
2. Fit the insert
Concave Mark
MILLING
Place the concave mark of the insert into the clamp-screw-fastening part of
the holder(only SRF type inserts). Fasten the clamp screw while firmly
pressing the insert against the insert seat wall. You are recommended to use
the special lubricant for preventing screw seizing, MK1KS, and to fasten with
recommended torque.
SPARE PARTS
TECHNICAL DATA
P001
Q001
L123
INDEXABLE MILLING
K
Cast Iron
Fig.1
B5
DCON
M
Stainless Steel
Including
Flat faces
Finishing
DC
P
Steel
BD
RADIUS END MILL

SUF
Hardened Steel
LU
RE
LH
LF
B2
DC
DCON
BD
Fig.2
RE
LU
a Highly accurate corner radius tolerance
allows for high precision finishing.

a Seamless gash.
LF
BD
Fig.3
LH
DC
DCON
B5
RE
LU
B2
LH
LF
Number of Teeth
LF
10
12
110
9.5
40
12
16
120
11.5
50
16
20
130
15.5
50
20
25
150
19.5
70
SRFH25S32M
25
32
180
24.5
SRFH30S32M
30
32
200
SRFH32S32M
32
32
200
SRFH10S12L
10
12
150
9.5
60
SRFH12S16L
12
16
160
11.5
70
SRFH16S20L
16
20
160
15.5
70
SRFH20S25L
20
25
180
19.5
80
SRFH20S20L80
20
20
180
19.5
80
24
SRFH25S32L
25
32
200
24.5
100
30
SRFH25S25L100
25
25
200
24.5
100
30
2 RS6025T xTKY25T SUFT25Rpp
SRFH30S32L
30
32
230
29.5
130
35
SRFH20S25E
20
25
220
19.5
120
24
SRFH20S20E120
20
20
220
19.5
120
24
SRFH25S32E
25
32
250
24.5
150
30
SRFH25S25E150
25
25
250
24.5
150
30
SRFH30S32E
30
32
300
29.5
200
35
SRFH10S12M
SRFH12S16M
SRFH16S20M
SRFH20S25M
L124
B2
B5
13
138
1 RS3008T zTKY08D SUFT10Rpp
15
236
20
244
24
223 130
80
30
258 130
29.5
100
35
31.5
100
35
13
130
15
147
20
151
24
203 130
Dimensions (mm)
BD
LH
LU
217 130
130 130
130 130
Clamp Screw
Wrench
Insert


(Note) Ensure inserts are fitted in the correct way. (Refer to page L126.)
Type (Fig.)
Standard
Semi-long
DC DCON
Order Number
Long
MILLING

Stock
Type
y STEEL SHANK TYPE
DC
DCON
BD
Fig.1
RE
LU
LH
LF
Long
DC
DCON
LF
Type (Fig.)
Clamp Screw
10
10
110
9.5
40
13
RS3008T zTKY08D SUFT10Rpp
12
12
120
11.5
50
15
16
16
130
15.5
50
20
RS4015T xTKY15T SUFT16Rpp
20
20
180
19.5
80
24
25
25
200
24.5
100
30
30
32
230
29.5
130
35
32
32
231
29.5
131
36
RS8030T xTKY30T
Stock
Order Number
Number of Teeth
Standard
Type
SRFH10S10MW
SRFH12S12MW
SRFH16S16MW
SRFH20S20MW
SRFH25S25MW
Dimensions (mm)
BD
LH
LU
Wrench
Insert
SUFT30Rpp
SRFH30S32MW
SRFH10S10LW
10
10
150
9.5
60
13
SRFH12S12LW
12
12
160
11.5
70
15
SRFH16S16LW
16
16
160
15.5
70
20
SRFH20S20LW
20
20
250
19.5
150
24
SRFH25S25LW
25
25
300
24.5
200
30
30
32
350
29.5
250
35
32
32
351
29.5
251
36
RS8030T xTKY30T
SRFH30S32LW
SUFT32Rpp
SUFT30Rpp
SUFT32Rpp
(Note 1) SRFH30S32MW and SRFH30S32LW tool body can use both inserts SUFT30Rpp and SUFT32Rpp.
However, the overall length size LF is different respectively.
(Note 2) Ensure inserts are fitted in the correct way. (Refer to page L126.)
A
APMX
LF
H
L11
A-A section
OAL
y SCREW-IN TYPE
Coolant Hole
DC DCON BD
SRFH16AM0830
16
8.5
SRFH20AM1035
20
SRFH25AM1240
25
SRFH30AM1645
Stock
Number of Teeth
Order Number
MILLING
RE
BD
DC
DCON
CRKS
Dimensions (mm)
WT
*1
(kg)
OAL
LF
L11
CRKS
14.9
48
30
10
0.1
RS4015T TKY15T SUFT16Rpp
10.5
18.4
54
35
14
10
0.1
12.5
23.5
62
40
19
12
0.1
30
17
28.1
68
45
24
16
32
17
28.1
69
46
24
16
0.2
RS8030T TKY30T
Clamp Screw Wrench
Insert
SUFT30Rpp
SUFT32Rpp
(Note 1) SRFH30AM1645 tool body can use both inserts SUFT30Rpp and SUFT32Rpp.
However, the overall length size OAL is different respectively.
1 Clamp Torque (N m) : RS4015T=3.3, RS5020T=5.0, RS6025T=7.5, RS8030T=10.0
2 WT : Tool Weight
*
*
SPARE PARTS
TECHNICAL DATA
P001
Q001
L125
INDEXABLE MILLING
INSERTS
BS APMX
a a
10
0.5
1.5
8.5 2.6
SUFT10R10
a a
10
8.5 2.6
SUFT10R20
a a
10
8.5 2.6
SUFT12R05
a a
12
0.5
1.2
1.7 10
SUFT12R10
a a
12
1.2
2.2 10
SUFT12R20
a a
12
1.2
3.2 10
SUFT12R30
a a
12
1.2
4.2 10
SUFT16R05
a a
16
0.5
1.6
2.1 12
SUFT16R10
a a
16
1.6
2.6 12
SUFT16R15
a a
16
1.5
1.6
3.1 12
SUFT16R20
a a
16
1.6
3.6 12
SUFT16R30
a a
16
1.6
4.6 12
SUFT20R05
a a
20
0.5
2.5 15
SUFT20R10
a a
20
15
SUFT20R15
a a
20
1.5
3.5 15
SUFT20R20
a a
20
15
SUFT20R30
a a
20
15
SUFT25R05
a a
25
0.5
2.5
18.5 6
SUFT25R10
a a
25
2.5
3.5 18.5 6
SUFT25R20
a a
25
2.5
4.5 18.5 6
SUFT25R30
a a
25
2.5
5.5 18.5 6
SUFT30R05
a a
30
0.5
3.5 22.5 7
SUFT30R10
a a
30
22.5 7
SUFT30R20
a a
30
22.5 7
SUFT30R30
a a
30
22.5 7
SUFT32R05
a a
32
0.5
3.2
3.7 23.5 7
SUFT32R10
a a
32
3.2
4.2 23.5 7
SUFT32R20
a a
32
3.2
5.2 23.5 7
Geometry
RE0.010
-0 0
.0
2
C
D
MILLING
FITTING INSERTS ON HOLDERS

1. Clean the insert seat
Clean the insert seat in the holder body by blowing air or using a brush.
2. Fit the insert

Place the concave mark of the insert into the clamp-screw-fastening part of
the holder(only SRF type inserts). Fasten the clamp screw while firmly
pressing the insert against the insert seat wall. You are recommended to use
the special lubricant for preventing screw seizing, MK1KS, and to fasten with
recommended torque.
L126
APMX
L0.015
RE
BS
SUFT10R05
DC
Order Number
Dimensions (mm)
Shape
MP8010
VP15TF
Coated
Concave Mark
y SHOULDER MILLING(When small width of cut. )

Hardness
Grade
Cutting Speed
vc
(m/min)
Depth of Cut
ap
(mm)
Cutting Width
ae
(mm)
Carbon Steel
Alloy Steel
180280HB
VP15TF
200 (80 300)
0.05DC
0.05DC
0.2 (0.4)
Pre-Hardened Steel
45HRC
VP15TF
150 (80 200)
0.05DC
0.05DC
0.15 (0.3)
Alloy Tool Steel
180380HB
VP15TF
150 (80 200)
0.05DC
0.05DC
0.15 (0.3)
Stainless Steel
270HB
VP15TF
150 (100 200)
0.05DC
0.05DC
0.2 (0.4)
Gray Cast Iron
Tensile Strength
MP8010
250 (180 450)
0.05DC
0.1DC
0.3 (0.4)
Ductile Cast Iron
Tensile Strength
MP8010
200 (80 300)
0.05DC
0.1DC
0.3 (0.4)
Hardened Steel
45 55HRC
MP8010
100 (80 120)
0.05DC
0.02DC
0.1 (0.2)
Hardened Steel
5565HRC
MP8010
80 (60 100)
0.05DC
0.02DC
0.1 (0.2)
Work Material
M
K
350MPa
800MPa
Feed per Tooth

fz
(mm/t.)
* When the pick feed direction is along the axis of the tool such as finish machining at the wall part.
y SLOTTINGSHOULDER MILLING(When large width of cut. )

Grade
Cutting Speed
vc
(m/min)
Depth of Cut
ap
(mm)
Cutting Width
ae
(mm)
M
K
Carbon Steel
Alloy Steel
180280HB
VP15TF
200 (80 300)
0.02DC
DC
0.2 (0.4)
Pre-Hardened Steel
45HRC
VP15TF
150 (80 200)
0.02DC
DC
0.15 (0.3)
Alloy Tool Steel
180380HB
VP15TF
150 (80 200)
0.02DC
DC
0.15 (0.3)
Stainless Steel
270HB
VP15TF
150 (100 200)
0.02DC
DC
0.2 (0.4)
Gray Cast Iron
Tensile Strength
MP8010
250 (180 450)
0.03DC
DC
0.3 (0.4)
Ductile Cast Iron
Tensile Strength
MP8010
200 (80 300)
0.03DC
DC
0.3 (0.4)
Hardened Steel
45 55HRC
MP8010
100 (80 120)
0.01DC
DC
0.1 (0.2)
Hardened Steel
5565HRC
MP8010
70 (60 80)
0.01DC
DC
0.1 (0.2)
350MPa
800MPa
Feed per Tooth

fz
(mm/t.)
MILLING
Hardness
Work Material
* When the pick feed direction is along the axis of the tool such as finish machining at the wall part.
(Note 1) This cutting condition is the standard condition when using the steel standard shank type. If it is occurred vibration or chipping on the
cutting edge, please decrease the cutting condition as width of cut, depth of cut and feed per tooth depending on the situation.
(Note 2) The value of cutting speed is stood at the peripheral diameter of the tool. Please calculate the spindle speed of tool in the following
expressions.
Spindle speed of cutting tool n(min-1)=1000Cutting speed vc uDiameter of cutting tool DCu3.14
(Note 3) Please note the following when machining hardened steel with MP8010.
L127
INDEXABLE MILLING
BALL NOSE
END MILL
Roughing
SRM2
K
Cast Iron
a Long Neck Type

APMX
DCON
M
Stainless Steel
Including
curved faces
DC
P
Steel
a Suitable for roughing to semi-finishing of small and medium moulds.

a Through coolant hole type.
H
Hardened Steel
PRFRAD
LH
LF
a Long Neck Cutting Edge Type
B5
APMX
PRFRAD
LU
DC
DC
DCON
APMX
PRFRAD
B2 (Draft Angle)
LH
DCON
a Standard Type
LH
LF
LF
a Long Cutting Edge Type

APMX
a Extra Long Cutting Edge Type

APMX
PRFRAD
LU
DCON
B2 (Draft Angle)
DC
DC
DCON
B5
B2 (Draft Angle)
LU
PRFRAD
LH
LH
LF
LF
SRM2160SAM
a u
16 20 130 50 25
12 248 130 TS25H
zTKY08D
SRM2200SNM
2 10
20 25 150 70 35
14 227 130 TS32
zTKY08D
SRM2200SAM
a u
2 10
20 25 150 70 35
14 227 130 TS32
zTKY08D
SRM2250SNM
2 12.5 25 32 180 80 40
19 313 130 TS43
xTKY15T
SRM2250SAM
a u
2 12.5 25 32 180 80 40
19 313 130 TS43
xTKY15T
SRM2300SNM
2 15
30 32 200 100 50
24 044 030 TS55
xTKY25T
SRM2300SAM
a u
2 15
30 32 200 100 50
24 044 030 TS55
xTKY25T
SRM2200SNL
4 10
20 25 150 70 35
30 227 130 TS32 TS25 zTKY08D zTKY08D
SRM2200SAL
a u
4 10
20 25 150 70 35
30 227 130 TS32 TS25 zTKY08D zTKY08D
SRM2250SNL
4 12.5 25 32 180 80 40
37 313 130 TS43 TS25 xTKY15T cTKY08F
SRM2250SAL
a u
4 12.5 25 32 180 80 40
37 313 130 TS43 TS25 xTKY15T cTKY08F
SRM2300SNL
4 15
30 32 200 100 50
44 044 030 TS55 TS43 xTKY25T cTKY15F
SRM2300SAL
a u
4 15
30 32 200 100 50
44 044 030 TS55 TS43 xTKY25T cTKY15F
SRM2160SNF
16 16 150 70
12
TS25H
zTKY08D
SRM2160SAF
a u
16 16 150 70
12
TS25H
zTKY08D
SRM2200SNF
2 10
20 20 180 100
14
TS32
zTKY08D
SRM2200SAF
a u
2 10
20 20 180 100
14
TS32
zTKY08D
SRM2250SNF
2 12.5 25 25 200 120
19
TS43
xTKY15T
SRM2250SAF
a u
2 12.5 25 25 200 120
19
TS43
xTKY15T
SRM2300SNF
2 15
30 32 230 150
24
TS55
xTKY25T
SRM2300SAF
a u
2 15
30 32 230 150
24
TS55
xTKY25T
Standard
Long Cutting Edge
Long Neck
B5
zTKY08D
B2
APMX
12 248 130 TS25H
LU
16 20 130 50 25
LH
LF
DC
DCON
PRFRAD
Inner, Outer Peripheral Inner, Outer Peripheral

Clamp Screw
Wrench
* Clamp Torque (N m) : TS25H=1.0, TS25=1.0, TS32=1.0, TS43=3.5, TS55=7.5

L128
*z
SRM2160SNM
Order Number
MILLING
Dimensions (mm)
Stock
Coolant Hole
Number of Teeth
Type
Inner
Outer
Insert
Peripheral
SRG16C
SRM16C-M
SRG16C
SRM16C-M
SRG20C
SRM20C-M
SRG20C
SRM20C-M
SRG25C
SRM25C-M
SRG25C
SRM25C-M
SRG30C
SRM30C-M
SRG30C
SRM30C-M
SRG16E
SRM16E-M
SRG16E
SRM16E-M
SRG20E
SRM20E-M
SRG20E
SRM20E-M
SRG25E
SRM25E-M
SRG25E
SRM25E-M
SRG30E
SRM30E-M
SRG30E
SRM30E-M
SRG20C
SRM20C-M
SRG20C
SRM20C-M
SRG25C
SRM25C-M
SRG25C
SRM25C-M
SRG30C
SRM30C-M
SRG30C
SRM30C-M
SRG20E
SRM20E-M
SRG20E
SRM20E-M
SRG25E
SRM25E-M
SRG25E
SRM25E-M
SRG30E
SRM30E-M
SRG30E
SRM30E-M
APMT1135
PDER-p2
APMT1135
PDER-p2
APMT1135
PDER-p2
APMT1135
PDER-p2
APMT1604
PDER-p2
APMT1604
PDER-p2
SRG16C
SRM16C-M
SRG16C
SRM16C-M
SRG20C
SRM20C-M
SRG20C
SRM20C-M
SRG25C
SRM25C-M
SRG25C
SRM25C-M
SRG30C
SRM30C-M
SRG30C
SRM30C-M
SRG16E
SRM16E-M
SRG16E
SRM16E-M
SRG20E
SRM20E-M
SRG20E
SRM20E-M
SRG25E
SRM25E-M
SRG25E
SRM25E-M
SRG30E
SRM30E-M
SRG30E
SRM30E-M
B5
4 10
20 20 180 100
30
TS32 TS25 zTKY08D zTKY08D SRM20C-M SRM20E-M PDER-p2
SRM2200SALF
a u
4 10
20 20 180 100
30
SRM2250SNLF
4 12.5 25 25 200 120
37
TS43 TS25 xTKY15T cTKY08F SRM25C-M SRM25E-M PDER-p2
SRM2250SALF
a u
4 12.5 25 25 200 120
37
SRM2300SNLF
4 15
30 32 230 150
44
SRM2300SALF
a u
4 15
30 32 230 150
44
SRM2200SNLL
4 10
20 25 250 120 35
30 130
SRM2200SALL
a u
4 10
20 25 250 120 35
30 130
SRM2250SNLL
4 12.5 25 32 300 170 37
37 130
SRM2250SALL
a u
4 12.5 25 32 300 170 37
37 130
SRM2300SNLL
4 15
30 32 350 100 50
44 130
TS55 TS43 cTKY25T cTKY15F SRM30C-M SRM30E-M PDER-p2
SRM2300SALL
a u
4 15
30 32 350 100 50
44 130
TS55 TS43 cTKY25T cTKY15F SRM30C-M SRM30E-M PDER-p2
LH
LF
SRM2200SNLF
DC
B2
APMX
DCON
LU
Long Neck Cutting Edge
*z
Inner, Outer Peripheral Inner, Outer Peripheral

Clamp Screw
Wrench
Extra Long Cutting Edge
PRFRAD
Stock
Coolant Hole
Number of Teeth
Type
Order Number
Dimensions (mm)
Inner
Outer
Insert
Peripheral
SRG20C
SRG20E
APMT1135
SRG20C
SRG20E
APMT1135
SRG25C
SRG25E
APMT1135
SRG25C
SRG25E
APMT1135
SRG30C
SRG30E
APMT1604
SRG30C
SRG30E
APMT1604
SRG20C
SRG20E
APMT1135
SRG20C
SRG20E
APMT1135
SRG25C
SRG25E
APMT1135
SRG25C
SRG25E
APMT1135
SRG30C
SRG30E
APMT1604
SRG30C
SRG30E
APMT1604
* Clamp Torque (N m) : TS25H=1.0, TS25=1.0, TS32=1.0, TS43=3.5, TS55=7.5
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a a
a a
1.2
1.4
18
18
18
18
18
18
18
18
0.8
0.8
11
10
10
10
10
11
9
9
9
9
11
10
10
10
10
11
9
9
9
9
11
11
Geometry
PRFRAD
PRFRAD
PRFRAD
PRFRAD
APMT1135PDER-M2 M
APMT1604PDER-M2 M
a a
a a
11
6.35 3.5 1.2 0.8 11
16.5 9.525 4.76 1.4 0.8 11
AN
AN
B9
AN
AN
RE
85
Low Resistance
Type
B9
L
MILLING
16
8.2 3.5
19 10.2 4.6
24 12.8 5.5
28 15.3 7
28 16.3 7
13.5 6.7 3.5
15.5 8.5 4.6
20.5 10.2 5.5
25.2 12.2 7
26.1 13.1 7
16
8.2 3.5
19 10.2 4.6
24 12.8 5.5
28 15.3 7
28 16.3 7
13.5 6.7 3.5
15.5 8.5 4.6
20.5 10.2 5.5
25.2 12.2 7
26.1 13.1 7
11
6.35 3.5
16.5 9.525 4.76
B9
BS
8
10
12.5
15
16
8
10
12.5
15
16
8
10
12.5
15
16
8
10
12.5
15
16
BS RE AN
W1
W1
W1
W1
G
G
G
G
G
G
G
G
G
G
M
M
M
M
M
M
M
M
M
M
M
M
AN
S
L
RE
BS
Peripheral
SRG16C
SRG20C
SRG25C
SRG30C
SRG32C
Strong Cutting SRG16E
Edge Type
SRG20E
SRG25E
SRG30E
SRG32E
Low Resistance SRM16C-M
Type
SRM20C-M
SRM25C-M
SRM30C-M
SRM32C-M
Low Resistance SRM16E-M
Type
SRM20E-M
SRM25E-M
SRM30E-M
SRM32E-M
Strong Cutting APMT1135PDER-H2
Edge Type
APMT1604PDER-H2
PRFRAD
W1
Outer
Inner
Outer
Inner
Strong Cutting
Edge Type
Order Number
W1
Shape
Dimensions(mm)
W1
Coated
Class
F7030
VP15TF
Application
INSERTS
85
AN
L
(Low-resistance inner or outer inserts are precision M class type.)

Selection guide for peripheral cutting edges : The first recommendation is the super sharp M breaker (APMT....PDER-M2).
When cutting edge strength is particularly important, use the H breaker (APMT....PDER-H2).
SPARE PARTS
TECHNICAL DATA
P001
Q001
L129
INDEXABLE MILLING
DC
DCON
CRKS
PRFRAD
BD
a Standard Type
APMX
LF
L11
OAL
A-A section
A
DC
DCON
CRKS
APMX
LF
PRFRAD
BD
a Long Cutting Edge Type
L11
OAL
A-A section
y SCREW-IN TYPE
SRM2200AM10S35
a u
10
SRM2250AM12S40
a u
SRM2300AM16S45
a u
15
30 17
SRM2320AM16S45
a u
16
32 17
Standard
Long Cutting Edge
a u
16 8.5 14.6 48 30 6 10 M8 12 0.1 TS25H
zTKY08D
20 10.5 18.6 54 35 6 14 M10 14 0.1 TS32
zTKY08D
12.5 25 12.5 23.5 62 40 6 19 M12 19 0.2 TS43
xTKY15T
28.3 68 45 6 24 M16 24 0.2 TS55
xTKY25T
30.0 68 45 6 24 M16 28 0.2 TS55
xTKY25T
10
APMX
CRKS
L11
LF
OAL
BD
WT
DCON
SRM2200AM10L45
*1 z
DC
a u
Order Number
*1
PRFRAD
SRM2160AM08S30
Type
Stock
Coolant Hole
Dimensions (mm)
(kg)
Inner, Outer Peripheral

Clamp Screw
20 10.5 18.6 64 45 6 14 M10 30 0.2 TS32
Wrench
TS25
zTKY08D
xTKY15T
cTKY08F
xTKY25T
cTKY15F
xTKY25T
cTKY15F
SRM2250AM12L55
a u
12.5 25 12.5 23.5 77 55 6 19 M12 37 0.3 TS43
TS25
SRM2300AM16L60
a u
15
30 17
28.3 83 60 6 24 M16 44 0.3 TS55
TS43
SRM2320AM16L60
a u
16
32 17
29.0 83 60 6 24 M16 44 0.3 TS55
TS43
Inner
Outer
Insert
Peripheral
SRG16C
SRM16C-M
SRG20C
SRM20C-M
SRG25C
SRM25C-M
SRG30C
SRM30C-M
SRG32C
SRM32C-M
SRG16E
SRM16E-M
SRG20E
SRM20E-M
SRG25E
SRM25E-M
SRG30E
SRM30E-M
SRG32E
SRM32E-M
SRG20C
SRM20C-M
SRG25C
SRM25C-M
SRG30C
SRM30C-M
SRG32C
SRM32C-M
SRG20E
SRM20E-M
SRG25E
SRM25E-M
SRG30E
SRM30E-M
SRG32E
SRM32E-M
APMT1135
PDER-p2
APMT1135
PDER-p2
APMT1604
PDER-p2
APMT1604
PDER-p2

1 Clamp Torque (N m) : TS25H=1.0, TS25=1.0, TS32=1.0, TS43=3.5, TS55=7.5
2 WT : Tool Weight
*
*

MILLING
Tool Overhang
The recommended cutting conditions are chosen based on deflection, vibration and
surface finish when using a BT50 arbor under the conditions below -"a", a length from a
gauge line to the arbor end face and "b", a neck length (tool overhang from the arbor).
Cutting Edge
Diameter:DC
16
20
25
DC
ap
max.
Inner/Outer
Maximum Cutting
Edge Length
Peripheral
(Long Cutting Edge)
L130
30
Type
Standard
Long Neck
Extra Long
Standard
Long Neck
Extra Long
Standard
Long Neck
Extra Long
Standard
Long Neck
Extra Long
105
50
70
70
100
150
80
120
200
100
150
250
155
175
175
205
255
185
225
305
205
255
355
Recommended Depth of Cut for Long Cutting Edge Type

The maximum cutting edge length of the long cutting edge type with a peripheral
insert is 1.4-1.5DC. The peripheral inserts main purpose is to remove the small
un-machined portions of the pre-machined surface above the main cutting edge.
Recommended depth of cut: Maximum ap is 0.5DC or below.
ap
Work Material
N : Revolution (min-1)
F : Table Feed (mm/min)
Cutting Speed Insert

Holder
Hardness (
m/min) Grade, Type Type
Standard 3183
180280HB
VP15TF
160
Low Resistance Long Neck 3183
(120200)
Type
Carbon Steel
Alloy Steel
Extra Long
Standard 2785
280350HB
VP15TF
140
(120160)
Type
Extra Long
Standard 2387
Pre-Hardened
Steel
VP15TF
120
3545HRC
(100160)
Type
Extra Long
Standard 2785
Alloy Tool Steel
< 350HB
VP15TF
140
(120160)
Type
Extra Long
Standard 3979
Stainless Steel
< 270HB
VP15TF
200
(100250)
Type
Extra Long
Standard 3979
Gray Cast Iron
< 350MPa
VP15TF
200
(150300)
Type
Extra Long
Standard 3581
Ductile Cast Iron
< 500MPa
VP15TF
180
(150240)
Type
Extra Long
Standard 3183
Ductile Cast Iron
< 800MPa
VP15TF
160
(150250)
Type
Extra Long
Standard 1989
Hardened Steel
4550HRC
VP15TF
100
Strong Cutting Long Neck 1989
(60120)
Edge Type
Extra Long
Standard 1194
Hardened Steel
5060HRC
VP15TF
60
Strong Cutting Long Neck 1194
(40100)
Edge Type
Extra Long
&16
F
ap
&20
F
ap
&30
F
382
2546
306
2037
489 12.5
1698
407
382
2546
306
2037
489
1698
407
7.5
2546
306
2037
489
1698
407
334
2228
334
2228
267
1783
428 12.5
1485
357
15
267
1783
428
1485
357
7.5
2228
267
1783
428
1485
357
286
1910
229
1528
367 12.5
1273
306
15
286
1910
229
1528
367
1273
306
7.5
1910
229
1528
367
1273
306
334
2228
267
1783
535 10
1485
594
12
334
2228
267
1783
535
1485
594
4.5
2228
267
1783
535
2.5
1485
594
1.5
477
3183
382
2546
764
2122
849
7.5
477
3183
382
2546
611
2122
637
4.5
3183
382
1.5
2546
509
1.5
2122
509
1.5
796
3183
637
2546 1019 12.5
2122
849
796
3183
637
2546 1019
7.5
2122
849
4.5
3183
637
2546 1019
2122
849
716
2865
573
2292
917 12.5
1910
764
15
716
2865
573
2292
917
7.5
1910
764
4.5
2865
573
2292
917
1910
764
1.5
637
2546
509
2037
815 12.5
1698
679
637
2546
509
2037
815
7.5
1698
679
4.5
2546
509
2037
815
1698
679
1.5
239
1591
191
1273
255
1061
212
7.5
239
1591
191
1273
255
1061
212
1591
191
1273
255
2.5
1061
212
1.5
143
955
115
764
153
637
127
7.5
143
955
115
764
153
637
127
955
115
764
153
2.5
637
127
1.5
SCREW-IN ARBORS
SPARE PARTS
TECHNICAL DATA
&25
F
ap
ap
15
15
15
L145
P001
Q001
MILLING
Cutting Mode
y SLOT MILLING
L131
INDEXABLE MILLING
ap
Cutting Mode
y SHOULDER MILLING (Cutting Depth : Small)
ae
Work Material

Holder
Hardness (
&16
ap
Standard 3979 796
180280HB
VP15TF
200
Low Resistance Long Neck 3979 637
(160250)
Type
Carbon Steel
Alloy Steel
Extra Long
Standard 3183 509
280350HB
VP15TF
160
(120200)
Type
Extra Long
Standard 3183 509
Pre-Hardened
Steel
VP15TF
160
3545HRC
(120200)
Type
Extra Long
Standard 3183 509
Alloy Tool Steel
< 350HB
VP15TF
160
(120200)
Type
Extra Long
Standard 3979 477
Stainless Steel
< 270HB
VP15TF
200
(100250)
Type
Extra Long
Standard 3979 1592
Gray Cast Iron
< 350MPa
VP15TF
200
(150300)
Type
Extra Long
Standard 3979 1592
Ductile Cast Iron
< 500MPa
VP15TF
200
(150280)
Type
Extra Long
Standard 3581 1432
MILLING
Ductile Cast Iron
< 800MPa
VP15TF
180
(150250)
Type
Extra Long
Standard 1989 239
Hardened Steel
4550HRC
VP15TF
100
Strong Cutting Long Neck 1989 239
(60120)
Edge Type
Extra Long
Standard 1194 143
Hardened Steel
L132
5060HRC
VP15TF
60
(40100)
Edge Type
Extra Long
ae
&20
ap
ae
&25
ap
3183 955
8 2546 1273
ae
10
&30
ap
ae
2122 1273 7.5 10
3183 637
6 2546 1273
7.5 2122 1273 7.5
7.5
3183 382
4 2546 1019
2546 509
8 2037 815
10
2546 407
6 2037 611
7.5 1698 509 7.5
7.5
2546 306
4 2037 489
2546 509
8 2037 815
10
2546 407
6 2037 611
7.5 1698 679 7.5
7.5
2546 306
4 2037 489
2546 509
8 2037 815
10
2546 407
6 2037 611
7.5 1698 509 7.5
7.5
2546 306
4 2037 489
2.5 1698 407 7.5
1.5
3183 509
8 2546 764
3183 382
6 2546 611
7.5 2122 849 7.5
7.5
3183 382
4 2546 509
1.5
3183 1592
10 2546 1528
10
2122 1485 7.5 10
3183 1273
8 2546 1528
10
2122 1485 7.5
3183 955
6 2546 1273
7.5 2122 1061 7.5
3183 1592
10 2546 1528
10
2122 1273 7.5 10
3183 1273
8 2546 1528
10
2122 1273 7.5
3183 955
6 2546 1273
7.5 2122 1061 7.5
2865 1433
10 2292 1375
10
1910 1146 7.5 10
10
10
2122 637 7.5
1698 849 7.5 10
1698 407 7.5
1698 849 7.5 10
1698 509 7.5
1698 849 7.5 10
2122 849 7.5 10
2122 424 7.5
2865 1146
8 2292 1375
1910 1146 7.5
2865 860
6 2292 1146
7.5 1910 955 7.5
1591 191
5 1273 255
7.5 1061 212 7.5
1591 191
3 1273 255
1.5
1591 191
2 1273 204
1.5 1061 170 7.5
955 115
764 153
7.5
637 127 7.5
955 115
764 153
637 127 7.5
1.5
955 115
764 122
1.5
637 102 7.5
1061 212 7.5
(Note) Machining Stainless Steels
ae
Work Material

Holder
Hardness (
&16
ap
Standard 3979 637
VP15TF
200
180280HB
(160250)
Type
Carbon Steel
Alloy Steel
Extra Long
Standard 3183 382
280350HB
VP15TF
160
(120200)
Type
Extra Long
Standard 3183 382
Pre-Hardened
Steel
VP15TF
160
3545HRC
(120200)
Type
Extra Long
Standard 3183 382
Alloy Tool Steel
< 350HB
VP15TF
160
(120200)
Type
Extra Long
Standard 3979 477
Stainless Steel
< 270HB
VP15TF
200
(100250)
Type
Extra Long
Standard 3979 1194
Gray Cast Iron
< 350MPa
VP15TF
200
(150300)
Type
Extra Long
Standard 3979 1194
Ductile Cast Iron
< 500MPa
VP15TF
200
(150280)
Type
Extra Long
Standard 3581 1074
Ductile Cast Iron
< 800MPa
VP15TF
180
(150250)
Type
Extra Long
Standard 1989 239
Hardened Steel
4550HRC
VP15TF
100
(60120)
Edge Type
Extra Long
Standard 1194 143
Hardened Steel
5060HRC
VP15TF
60
(40100)
Edge Type
Extra Long
When up-cut milling stainless steels at large depths

and widths of cut, the machined surface is liable to
burrs and welding due to chip jamming. For stainless
steels, down-cutting (climb milling) is recommended.
&20
ap
ae
3183 764 10
2546 1273 12.5
2122 1273 15
4.5
2122 849 15
ae
&25
ap
ae
&30
ap
ae
3183 509 10
2546 1019 12.5
3183 382 10
2546 764 12.5
2.5 2122 849 15
1.5
2546 509 10
2037 815 12.5
1698 849 15
4.5
2546 306 10
2037 611 12.5
1698 509 15
2546 306 10
2037 489 12.5
2.5 1698 407 15
1.5
2546 509 10
2037 815 12.5
1698 849 15
4.5
2546 306 10
2037 611 12.5
1698 509 15
2546 306 10
2037 489 12.5
2.5 1698 407 15
1.5
2546 509 10
2037 815 12.5
4.5
2546 306 10
2037 611 12.5
2.5 1698 509 15
2546 306 10
2037 489 12.5
1.5 1698 407 15
1.5
3183 509 10
2546 764 12.5 10
2122 849 15
3183 382 10
2546 611 12.5
2122 509 15
4.5
3183 382 10
2546 489 12.5
1.5 2122 340 15
1.5
3183 1273 10
2546 1273 12.5 10
3183 955 10
2546 1273 12.5
7.5 2122 1061 15
4.5
3183 764 10
2546 1019 12.5
1.5 2122 849 15
3183 1273 10
2546 1273 12.5 10
3183 955 10
2546 1273 12.5
7.5 2122 849 15
4.5
3183 764 10
2546 1019 12.5
2122 849 15
1.5
2865 1146 10
2292 1146 12.5 10
1910 1146 15
1698 849 15
2122 1485 15
2122 1273 15
10
10
10
10
2865 860 10
2292 1146 12.5
7.5 1910 764 15
4.5
2865 688 10
2292 917 12.5
1910 764 15
1.5
1591 191 10
1273 255 12.5
1061 212 15
1591 191 10
1273 204 12.5
1.5 1061 106 15
1.5
1591 191 10
955 115 10
764 153 12.5
637 127 15
955 115 10
764 122 12.5
1.5
637
1.5
955 115 10
TECHNICAL DATA
64 15
MILLING
ap
Cutting Mode
y SHOULDER MILLING (Cutting Depth : Large)
Q001
L133
INDEXABLE MILLING
BALL NOSE
END MILL
SRM2
P
Including
curved faces
Roughing
40
50
a Combination Type
H
DCON
Cast Iron
DC
Steel
a Best for roughing of moulds.

a Highly rigid body.
PRFRAD
APMX
LH
LF
a Morse Taper Type
a Straight Type
DC
DC
DCON
M20
MT5
APMX
PRFRAD
APMX
LH
PRFRAD
LH
LF
LF
Type
Order Number
Stock
Number of Flutes
SRM2400WNLS
SRM2500WNLS
SRM2400WNLM
SRM2500WNLM
PRFRAD DC DCON
LF
LH APMX
200
200
250
250

Clamp Screw
TS6S TS43
TS6
TS43
TS6S TS43
TS6
TS43

Wrench
TKY30T TKY15F
TKY30T TKY15F
TKY30T TKY15F
TKY30T TKY15F
Inner
Peripheral
APMT1604
PDER-p2
APMT1604
PDER-p2
APMT1604
PDER-p2
APMT1604
PDER-p2
20
25
20
25
40
50
40
50
50.8
50.8
50.8
50.8
120
120
170
170
54
63
54
63
SRM2500WNLL
25
50
50.8 300 220
63
TS6
TS43
TKY30T TKY15F SRG50C SRG50E
APMT1604
PDER-p2
SRM2500WNLX
25
50
50.8 350 270
63
TS6
TS43
APMT1604
PDER-p2
SRM2400SNLS
SRM2500SNLS
SRM2400SNLM
SRM2500SNLM
2
2
2
2
20
25
20
25
40
50
40
50
42
42
42
42
100
100
150
100
54
63
54
63
TS6S
TS6
TS6S
TS6
TS43
TS43
TS43
TS43
TKY30T
TKY30T
TKY30T
TKY30T
SRG40E
SRG50E
SRG40E
SRG50E
APMT1604
PDER-p2
APMT1604
PDER-p2
APMT1604
PDER-p2
APMT1604
PDER-p2
SRM2500MNLS
25
50
256 120
63
TS6
TS43
APMT1604
PDER-p2
SRM2500MNLM
25
50
286 150
63
TS6
TS43
APMT1604
PDER-p2
a
a
a
a
200
200
250
250
TKY15F
TKY15F
TKY15F
TKY15F
SRG40C
SRG50C
SRG40C
SRG50C
SRG40C
SRG50C
SRG40C
SRG50C
* Clamp Torque (N m) : TS43=3.5, TS6=10.0, TS6S=10.0

INSERTS
* SRG40C
* SRG50C
G
G
a a a
a a a
PRFRAD
20
25
W1
36
40
20.5
26
8.0
8.5
Geometry
BS RE
G
G
a a a
a a a
20
25
32 16.6
35.8 20
8.0
8.5
11
PRFRAD
16.5
RE
9.525 4.76 1.4 0.8
85
a
16.5
RE
9.525 4.76 1.4 0.8
85
BS
APMT1604PDER-H2 M
11
S
W1
Peripheral
Strong Cutting
Edge Type
W1
APMT1604PDER-M2 M
11
L
: Inventory maintained in Japan. (10 inserts in one case)(Inserts with asterisk ( ) are available in 2 piece in one case)
11
W1
Outer
* SRG40E
* SRG50E
BS
Order Number
Dimensions (mm)
W1
Shape
Class
VP15TF
VP20RT
VP30RT
Application
Coated
PRFRAD
L134
Outer
Insert
SRG40E
SRG50E
SRG40E
SRG50E
2
2
2
2
Inner
MILLING
Combination
Morse Taper Straight
Long Standard Long Standard Extra Long Long Standard
Dimensions (mm)
1.0DC
0.2DC
Hardness
Grade
Cutting Speed
(m/min)
Alloy Tool Steel
< 250HB
VP20RT
VP30RT
160 (120 200)
Alloy Tool Steel
< 250HB
VP20RT
VP30RT
200 (160 250)
Cast Tool Steel
< 235HB
VP20RT
200 (160 250)
Cast Tool Steel
< 230HB
VP15TF
VP20RT
200 (160 300)
Work Material
K
Ductile Cast Iron
Tensile Strength
VP15TF
VP20RT
200 (160 300)
Gray Cast Iron
Tensile Strength
VP15TF
VP20RT
200 (160 300)
< 540MPa
< 350MPa
1.0DC
0.5DC
Cutting
Mode
C : Shoulder Milling (Long Cutting Edge Type)
0.5DC
B : Shoulder Milling (Standard Type)
A : Slot Milling
0.1DC
Feed per Tooth

(mm/t.)
Cutting
Mode
0.12 (0.08 0.2)

0.2 (0.1 0.4)
0.15 (0.1 0.3)
0.2 (0.1 0.3)
0.3 (0.1 0.4)
0.2 (0.1 0.4)
0.2 (0.1 0.3)
0.3 (0.1 0.4)
0.2 (0.1 0.4)
0.2 (0.1 0.3)
0.3 (0.1 0.45)
0.2 (0.1 0.4)
0.25 (0.1 0.4)
0.35 (0.1 0.45)
0.25 (0.1 0.45)
0.25 (0.1 0.4)
0.35 (0.1 0.45)
0.25 (0.1 0.4)
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
y GRADE APPLICATION GUIDE

Gray Cast Iron Ductile Cast Iron
JIS FC250
Cast Tool Steel
JIS FCD540
JIS GM241
JIS GM190
Alloy Tool Steel

JIS SX-105V
JIS SKD11
VP15TF
VP20RT
Wear Resistance
MILLING
VP30RT
Toughness
SPARE PARTS
TECHNICAL DATA
P001
Q001
L135
INDEXABLE MILLING
T-SLOT MILLING
Roughing
TSMP
M
L16
Cast Iron
DCON
DC
Steel
BD
a T-groove order number
R 0.8
4
L5
L6
APMX
LH
LF
DC
TSMPR252S25
14
25
112
25
12.5 33.2
32
12
17
11
TS3
zTKY08D
MPMW070308
TSMPR322S32
18
32
120
32
16
41.2
36
14
19
14
TS4
xTKY15R
MPMW090308
TSMPR402S32
22
40
130
32
20
51.2
36
14
19
18
TS5
xTKY25R
MPMW120408
Order Number
T Slot
Nomenclature
Stock
Number of Teeth
14, 18 and 22 are available.

a 86 rhombic shape 11
90
positive insert.
a Shoulder milling and inversed
spot facing are also possible.
Dimensions (mm)
LF DCON BD
LH
L16
L5
L6 APMX Clamp Screw
Wrench
Insert
INSERTS
Dimensions (mm)
IC
MPMW070308
7.94
3.18
0.8
MPMW090308
9.525
3.18
0.8
MPMW120408
4.76
0.8
12.7
Geometry
RE
RE
11
IC
86
MILLING

Work
Material
Hardness
Grade

(m/min)
(mm/rev)
180 280HB
UTi20T
130
(100 160)
280 350HB
UTi20T
80
(60100)
0.1
(0.050.15)
K Cast Iron Tensile Strength
UTi20T
100
(80 120)
0.15
(0.10.2)
Carbon Steel
Alloy Steel
< 450MPa
RE
0.15
(0.10.2)
y CAUTION FOR USE

a When T slot machining steel, the
Approx.
2mm
Order Number
Class
UTi20T
Carbide
Shape
workpiece must be machined as

shown in the drawing to ensure
smooth chip evacuation.
a Slots to be machined must be free
from chips for smooth machining.
T Slot
L136
SPARE PARTS
TECHNICAL DATA
P001
Q001
SPOT MILLING
M
Steel
Stainless Steel
Cast Iron
H
DC
L16
DCON
CBJP,CBMP
DMIN (Min. Diameter)
Roughing
L5
a Capable of spot facing machining,
L6
LU
boring and interpolation.
90
LH
LF
a For seat machining of hexagon socket
head bolt (M8-M30).
For
bolt
size
Order Number
Stock
Number of Teeth
a 86rhombic shape 11positive insert.
Dimensions (mm)
DC
DMIN
LF DCON LH
LU
L16 L5
L6
Clamp Screw
Wrench
Insert
CBJPR141S25
M8
1 14
3.1 108
25
28
21
32
12
17
TS3
zTKY08D
JPMT060204-E
CBJPR172S25
M10
2 17.5
5.3 115
25
35
26
32
12
17
TS3
zTKY08D
JPMT060204-E
CBJPR202S25
M12
2 20
7.8 120
25
40
30
32
12
17
TS3
zTKY08D
JPMT060204-E
CBJPR232S25
M14
2 23
10.8 126
25
46
34.5
32
12
17
TS3
zTKY08D
JPMT060204-E
CBMPR262S32
M16
2 26
8.5 132
32
52
39
36
14
19
TS4
xTKY15R
MPMT090308
CBMPR292S32
M18
2 29
11.5 138
32
58
43.5
36
14
19
TS4
xTKY15R
MPMT090308
CBMPR322S32
M20
2 32
14.5 144
32
64
59
36
14
19
TS4
xTKY15R
MPMT090308
CBMPR352S32
M22
2 35
17.5 150
32
70
70
36
14
19
TS4
xTKY15R
MPMT090308
CBMPR392S32
M24
2 39
21.5 158
32
78
78
36
14
19
TS4
xTKY15R
MPMT090308
CBMPR432S32
M27
2 43
25.5 166
32
86
86
36
14
19
TS4
xTKY15R
MPMT090308
CBMPR482S32
M30
2 48
30.5 176
32
96
96
36
14
19
TS4
xTKY15R
MPMT090308

INSERTS
Dimensions (mm)
6.5
a a
IC
RE
2.38
0.4
Geometry
RE
7.94
RE
11
L
MPMT090308
a a
9.525 3.18
RE
0.8
RE
CBMP
86
MILLING
CBJP
JPMT060204-E
Carbide
UTi20T
Order Number
Class
VP15TF
UP20M
Cutter Type
Coated
Shape
11
86
IC

Hardness
Grade
CBJP
Cutting Speed
Feed
(m/min)
(mm/rev)
CBMP
Cutting Speed
Feed
(m/min)
(mm/rev)
< 180HB
VP15TF
180 (100 200)
180 (100 200)
180 280HB
VP15TF
180 (100 200)
280 350HB
VP15TF
120 (80 160)
0.16 (0.120.2)
120 (80 160)
0.225 (0.15 0.3)
Stainless Steel
< 200HB
VP15TF
150 (100 200)
0.16 (0.120.2)
150 (100 200)
0.225 (0.15 0.3)
Cast Iron
Tensile Strength
VP15TF
160 (100 220)
0.3 (0.2 0.4)
160 (100 220)
0.35 (0.2 0.5)
Work Material
Mild Steel
Carbon Steel
Alloy Steel
M
K
< 450MPa
0.16 (0.120.2)
0.2 (0.150.25)
180 (100 200)
0.225 (0.15 0.3)

0.275 (0.2 0.35)
-1)
aRevolution (min =(1000 x Cutting Speed)u(3.14 x DC) aSpindle feed (mm/min) = Feed rate x Tool spindle speed
(Note) CBJPR141S25 use feed per revolution 50 % of this table, because only 1 insert on the body.
a
SPARE PARTS
TECHNICAL DATA
P001
Q001
L137
INDEXABLE MILLING
SLOT MILLING
Roughing
KSMG
M
L16
DM
IN
Min
. Cu
ttin
g
Dia
L5
CW
me
DCON
Cast Iron
CDX
Steel
DMIN/2
L6
LU
LH
ter
LF
machining centers.
a The minimum cutting diameter is
CDX
DMIN/2
a Side face grooving tool for
CW
LU
LF
Stock
Number of Teeth
& 25mm for internal grooving.

a For groove widths of 1.25mm 6.0mm.
Order Number
KSMGR40S32
KSMGR40S32L
Geometry of Groove
DMIN
Insert Number
25
MGTL33ppp
40
MGTL43ppp
40
MGTL44ppp
40
MGTL43pp
40
MGTL44ppp
(mm)
LF
DCON
1 115
Dimensions (mm)
KSMGR25S25
4.8 < Groove Width < 6.3
25
LH
LU
40
36.5
L16
32
L5
L6
12
17
130
32
50
49
36
14
19
131.6
32
51.6
50.6
36
14
19
180
181.6
32
32
100
99
101.6 100.6
36
36
14
19
14
19
CW
CDX
1.25
1.2
1.45
1.5
1.5 < CW < 4.0
3.0
1.25
1.2
1.45
1.5
1.5 < CW < 2.3
3.0
2.5 < CW < 4.7
4.5
4.8 < CW < 6.0
4.5
1.25
1.2
1.45
1.5
1.5 < CW < 2.3
3.0
2.5 < CW < 4.7
4.5
4.8 < CW < 6.0
4.5
MILLING
SPARE PARTS
Tool Holder Number

Clamp Lever
Spring
Lever Pin
KSMGR25S25
LLCL13S
HLS2
LLCS105
zHKY20F
KSMGR40S32
LLCL24
LLP14
LLCS108
xHKY30R
KSMGR40S32L
LLCL24
LLP14
LLCS108
xHKY30R

Work Material
Hardness
P
Mild Steel
< 180HB
Carbon Steel
Alloy Steel
Cast Iron
180 280HB
UTi20T
NX2525
UTi20T
280 350HB
UTi20T
Tensile Strength
UTi20T
(120 150)
160
(120 200)
110
(100 120)
120
(100 140)
110
(100 120)
100
(80 125)
(0.10.35)
0.225
(0.10.35)
0.2
(0.10.30)
0.2
(0.10.30)
0.175
(0.10.25)
0.225
(0.10.35)

-1)
Wrench
Cutting Speed Feed per Tooth y HONING OF CUTTING EDGE

(m/min)
(mm/t.)
Supplementary honing when steel cutting gives longer tool life.
NX2525
130
0.225
Use a diamond file for best results.
VP20MF
< 450MPa
Clamp Screw
Grade
VP20MF
L138
0.05 0.1
20 30
INSERTS
Stock
Dimensions (mm)
Grooving
Width
NX2525
CW
MGTL33125
1.25
MGTL33145
1.45
MGTL33150
1.5
MGTL33175
1.75
MGTL33200
MGTL33230
2.3
MGTL33250
2.5
MGTL33270
2.7
MGTL33280
2.8
MGTL33300
MGTL33320
3.2
MGTL33330
3.3
MGTL33350
3.5
MGTL33400
4.76
0.3
MGTL43125
1.25
12.7
4.76
0.2
1.2
MGTL43145
1.45
12.7
4.76
0.2
1.5
MGTL43150
1.5
12.7
4.76
0.2
MGTL43175
1.75
12.7
4.76
0.2
MGTL43200
12.7
4.76
0.2
MGTL43230
2.3
12.7
4.76
0.2
MGTL43250
2.5
12.7
4.76
0.3
4.5
MGTL43260
2.6
12.7
4.76
0.3
4.5
MGTL43270
2.7
12.7
4.76
0.3
4.5
MGTL43280
2.8
12.7
4.76
0.3
4.5
MGTL43300
12.7
4.76
0.3
4.5
MGTL43320
3.2
12.7
4.76
0.3
4.5
MGTL43330
3.3
12.7
4.76
0.3
4.5
MGTL43350
3.5
12.7
4.76
0.3
4.5
MGTL43400
12.7
4.76
0.3
4.5
MGTL43420
4.2
12.7
4.76
0.4
4.5
MGTL43430
4.3
12.7
4.76
0.4
4.5
MGTL43450
4.5
12.7
4.76
0.4
4.5
MGTL43470
4.7
12.7
4.76
0.4
4.5
MGTL44500
12.7
6.35
0.4
4.5
MGTL44600
12.7
6.35
0.4
4.5
UTi20T
Order Number
VP20MF

IC
RE
PDPT
9.525
4.76
0.2
1.2
9.525
4.76
0.2
1.5
9.525
4.76
0.2
9.525
4.76
0.2
9.525
4.76
0.2
9.525
4.76
0.2
9.525
4.76
0.3
9.525
4.76
0.3
9.525
4.76
0.3
9.525
4.76
0.3
9.525
4.76
0.3
9.525
4.76
0.3
9.525
4.76
0.3
PDPT
RE
CW 0.025
MILLING
9.525
MGTL...
IC
Geometry
SPARE PARTS
TECHNICAL DATA
P001
Q001
L139
INDEXABLE MILLING
VERTICAL FEED
MILLING
Roughing
PMC
M
H
A
CRKS
DCON
DC
Cast Iron
BD
P
Steel
1
2
a For under-cutting trimed
Order Number
Stock
Coolant Hole
Number of Teeth
part of press mould.

large overhang.
AE1(Max. Depth of Cut)

L4
LF
OAL
H
A-A section
L11
Dimensions (mm)
WT
Shank Arbor
(kg)
DC DCON BD OAL LF
L4 L11
H CRKS AE1
Insert
PMC08R252AM1035
a u
2 25 10.5 18 58.7 39.7 35
14 M10 1.5 40.5 35 0.1
JOMp080320
ZZSR-pp
SC20M10S
ppppW
PMC09R323AM1245
a u
3 32 12.5 21 72.5 50.5 45
19 M12 3
JDMp09T320
ZDSR-pp
SC25M12S
ppppW
PMC12R403AM1645
a u
3 40 17
24 M16 3.5 42
JDMp120420
ZDSR-pp
SC32M16S
ppppW
29 74.4 51.4 45
40.5 35 0.2
35 0.3
* WT : Tool Weight
SPARE PARTS
MILLING
Order Number
Clamp Screw
Clamp Bridge
Clamp
Bridge Screw
Spring
Wrench
Anti-seize
Lubricant
PMC08R252AM1035
TS33
AMS3
AJS3010T10
ASS2
xTKY08D
zTKY10R
MK1KS
PMC09R323AM1245
TS351
AMS3
AJS3010T10
ASS2
xTKY10D
MK1KS
PMC12R403AM1645
TS43
AMS4
AJS4012T15
ASS2
xTKY15D
MK1KS
* Clamp Torque (N m) : TS33=1.5, TS351=2.5, TS43=3.5, AJS3010T10=2.5, AJS4012T15=3.5

INSERTS
Dimensions (mm)
Order Number
Class
FH7020
VP15TF
VP30RT
Coated
Shape
AN
Partial Profile
FT Breaker
JOMW080320ZZSR-FT
a a a
13 8
3.18 1.4
PMC08R252AM1035
JDMW09T320ZDSR-FT
a a a
15 9.525 3.97 1.8
PMC09R323AM1245
JDMW120420ZDSR-FT
a a a
15 12
4.76 2.5
PMC12R403AM1645
JDMT120420ZDSR-ST
a a a
15 12
4.76 2.5
PMC12R403AM1645
Strong Cutting
Edge Type
ST Breaker
IC
BS
RE
PMC holder
Geometry
AN
BS
IC
IC
JOMT080320ZZSR-JM
a a a
13 8
3.18 1.4
PMC08R252AM1035
JDMT09T320ZDSR-JM
a a a
15 9.525 3.97 1.8
PMC09R323AM1245
JDMT120420ZDSR-JM
a a a
15 12
PMC12R403AM1645
4.76 2.5
L140
RE
AN
BS
IC
AN
BS
JM Breaker
RE
RE

Work Material
Carbon Steel
Alloy Steel
Alloy Tool Steel

Hardening Tool Steel
for Cold Work Dies
Alloy Tool Steel
Hardness
Grade
< 180HB
VP15TF
< 300HB
< 300HB
Tensile
Strength
Gray Cast Iron
Diameter Number Cutting Speed

Breaker (mm)
(m/min)
of Teeth
VP15TF
VP15TF
VP15TF
FT
FT
FT
FT
< 350MPa
Tensile
Strength
Ductile Cast Iron
VP15TF
FT
< 800MPa
Feed per Tooth

(mm/t.)
Width of Cut
(mm)
Pick Feed
(mm)
40
250 (200 300)
0.6
1.5
32
200 (150 220)
0.55
1.2
25
200 (150 220)
0.55
1.0
40
250 (200 300)
0.55
1.5
32
180 (150 200)
0.5
1.2
25
180 (150 200)
0.5
1.0
40
200 (100 300)
0.55
1.5
32
150 ( 80 200)
0.5
1.2
25
150 ( 80 200)
0.5
1.0
40
250 (200 300)
0.6
1.5
32
200 (150 220)
0.55
1.2
25
200 (150 220)
0.55
1.0
40
250 (200 300)
0.6
1.5
32
200 (150 220)
0.55
1.2
25
200 (150 220)
0.55
1.0

(Note 1) The above cutting conditions are general guide lines. Adjustments maybe necessary depending on machine rigidity, workpiece
geometry and clamping.
(Note 2) A carbide shank extension is recommended to prevent vibrations.
Application of Breakers
Cutting
Conditions
Breaker
Light
Cutting
General
Cutting
JM
Application of Insert Grades

Interrupted
Cutting
Cutting
Conditions
Light
Cutting
General
Cutting
Interrupted
Cutting
FH7020
FT
(1st Recommendation)
ST
VP15TF
Grade
(1st Recommendation)
VP30RT
NOTES ON MACHINING METHODS

a How to choose an appropriate diameter tool.
MILLING
Machine plain surfaces with a larger tool and corner radii with smaller diameter cutters.
Cutting point
PMC
Small
Diameter
PMC
Large
Diameter
PMC
a Relation of the cutter diameter and corner R size of work piece

A guide for the smallest possible workpiece radius that can be machined is from 0.6 0.7 x diameter of the tool.
C
or
=D ner
C R
x0
.6
~0
.
7
PMC
DC
Tool diameter
DC(mm)
Corner R
(mm)
& 25
R > 17.5
& 32
& 40
R > 22
R > 24
cutting conditions according to the set up.

*Adjust
Smaller workpiece corner radii (only >0.5 x cutter &) may be
*possible by reducing the width of cut, speed and pick feed.
ARBORS
SPARE PARTS
TECHNICAL DATA
L145
P001
Q001
L141
INDEXABLE MILLING
Finishing
LF
Cast Iron
LF
BD
DCON
KWW
L8
Steel
63
BD
DCON
KWW
CBDP
50
CBDP
PMF
L8
VERTICAL FEED
MILLING
DCCB
DC
DCCB
DC
80 BD
CBDP
LF
L8
DCON
KWW
a 2 directional cutting
with large overhang.

a Excellent straightness.
a Excellent wall accuracy.
DAH
DC
Stock
Number of Teeth
Order Number
Dimensions (mm)
Radial Set Bolt

DC LF DCON CBDP DAH DCCB KWW L8 BD Cartridge Clamp
Screw Screw (Cartridge) Wrench Wrench
PMF05004A22R
4 50 63 22 20
12 10.4 6.3 48 PMFA13R TS254 TSS04005 HBH06012 TKY08F
HKY40R
HKY50R
PMF06306A22R
6 63 63 22 20
18 10.4 6.3 60 PMFA13R TS254 TSS04005 HBH06012 TKY08F HKY40R xHSC10050 1303
PMF08008A27R
8 80 50 27 23 13.5 12.4 7
Set Bolt
zHDS10031
75 PMFA13R TS254 TSS04005 HBH06012 TKY08F HKY40R xHSC12035
Insert
TPEW
ZPpR2
* Clamp Torque (N m) : TS254=1.0, HBH06012=8.5
TPEW1303ZPTR2
Dimensions (mm)
IC
BS
7.94
3.18
7.94
3.18
a a
a
Geometry
60
BS
MILLING
TPEW1303ZPER2
CBN
BS
Order Number
Class
VP15TF
AP10H
Coated
Shape
MB710
INSERTS
11
IC
*MB710

Work
Material
Grade
180 280HB
VP15TF
250
(150 350)
280 380HB
VP15TF
200
(100 300)
Tensile
Strength
< 350MPa
AP10H
Carbon Steel
Alloy Steel
Gray Cast
Iron

(m/min)
(mm/t.)
Hardness
MB710
350
(200 500)
1500
(1000 2000)
Work
Material
K
0.1
(0.050.15)
Hardness
Grade
Ductile
Cast Iron
Tensile
Strength
360500MPa
AP10H
Ductile
Cast Iron
Tensile
Strength
500800MPa
AP10H
MB710
MB710

(m/min)
(mm/t.)
250
(150 350)
1000
(800 1200)
200
(100 300)
1000
(800 1200)
0.1
(0.05 0.15)
0.1
(0.05 0.15)
0.1
(0.050.15)

(Note 1) Recommended radial depth of cut is 0.1mm.

(Note 2) 2 directional vertical cutting is recommended for efficiency.
(Note 3) For crossfeed cutting, the feed per tooth should be reduced to less than 0.05(mm/t.).
L142

SPARE PARTS
TECHNICAL DATA
P001
Q001
VERTICAL FEED
MILLING
Roughing
PMR
M
KWW
L8
Cast Iron
LF
a 1 directional cutting with large overhang.

a Horizontal feed cutting and oblique
Stock
Order Number
Metric
Inch
Number of Teeth
(APMX)
cutting are
also possible.
a Unique shape of curved edge gives high
rigidity
and low resistance.
Type
CBDP
P
Steel
BD
DCON
DAH APMX
DC
Dimensions (mm)
Insert
DC
LF
DCON
CBDP DAH
BD
KWW
L8
APMX
PMR405003A22R
50
40
22
20
11
45
10.4
6.3
11
CPMT1205ZPEN-M2/3
PMR406304A22R
63
40
22
20
11
57
10.4
6.3
11
CPMT1205ZPEN-M2/3
PMR408005A27R
80
50
27
23
13
73
12.4
11
CPMT1205ZPEN-M2/3
PMR608004A27R
80
50
27
23
13
72
12.4
17
CPMT1906ZPEN-M2/3
PMR405003BR
50
40
22.225
19
11
45
8.4
11
CPMT1205ZPEN-M2/3
PMR406304BR
63
40
22.225
19
11
57
8.4
11
CPMT1205ZPEN-M2/3
PMR408005DR
80
63
31.75
32
17
73
12.7
11
CPMT1205ZPEN-M2/3
PMR608004DR
80
63
31.75
32
17
72
12.7
17
CPMT1906ZPEN-M2/3
SPARE PARTS
Tool Holder Number
Shim
Insert
Clamp Screw
Wrench (Insert) Wrench (Shim)
Shim
Shim Screw
Clamp Screw
STPMR4N
STPMR4N
STPMR4N
STPMR4N
STPMR4N
STPMR4N
STPMR6N
STPMR6N
WCS503507H
WCS503507H
WCS503507H
WCS503507H
WCS503507H
WCS503507H
WCS604010H
WCS604010H
zTPS35
zTPS35
zTPS35
zTPS35
zTPS35
zTPS35
xCSF401260T
xCSF401260T
Coated
Order Number
zTIP15T
zTIP15T
zTIP15T
zTIP15T
zTIP15T
zTIP15T
xTKY20D
xTKY20D
HKY35R
HKY35R
HKY35R
HKY35R
HKY35R
HKY35R
HKY40R
HKY40R
Set Bolt
HSC10035
HSC10035
HSC12035
HSC10035
HSC10035
HSC16040
HSC12035
HSC16040
CPMT1205ZPEN-M2
CPMT1205ZPEN-M3
Dimensions (mm)
IC
BS
RE
12.7
5.56
1.4
0.8
12.7
5.56
1.4
1.2
Geometry
RE
BS
VP15TF
Shape
* Clamp Torque (N m) : TPS35=3.5, CSF401260T=5.0, WCS503507H=5.0, WCS604010H=7.0

Class
INSERTS
PMR405003A22R
PMR406304A22R
PMR408005A27R
PMR405003BR
PMR406304BR
PMR408005DR
PMR608004A27R
PMR608004DR
MILLING
Shim Screw
80
19.05
6.35
1.4
0.8
CPMT1906ZPEN-M3
19.05
6.35
1.4
1.2
RE
BS
CPMT1906ZPEN-M2
IC
80
IC
SPARE PARTS
TECHNICAL DATA
P001
Q001
L143
INDEXABLE MILLING

Work Material
Carbon Steel
Alloy Steel
Gray Cast Iron
Hardness
Grade
pf (mm)
VP15TF
180 (150 200)
0.2 (0.1 0.3)
< 0.5DC
Tensile Strength
< 350MPa
VP15TF
180 (150 200)
0.2 (0.1 0.3)
< 0.5DC
Tensile Strength
360 500MPa
VP15TF
150 (120 170)
0.2 (0.1 0.3)
< 0.5DC
Tensile Strength
500 800MPa
VP15TF
120 (100 150)
0.2 (0.1 0.3)
< 0.5DC
180 280HB
280 380HB
Ductile Cast Iron

MILLING
(Note 1) The above conditions are suitable for general machining purposes, it is possible to use conditions that are different from the above.
(Note 2) For horizontal feed machining, please reduce the feed rate by 20 40%.
(Note 3) If vibration occurs when machining, please reduce the depth of cut, and reduce the cutting speed by 20 50%.
L144
ARBORS
ARBORS FOR SCREW-IN TOOLS
Order Number
Dimensions (mm)
Stock
Type
y STRAIGHT SHANK ARBOR
STEEL SHANK TYPE
DCB DCON BD
LB
LF
CARBIDE SHANK TYPE
BD
DCB
DCON
CRKS
LF
LB
CRKS
SC16M08S100S
8.5
16
14.5 100
10
10
M8
SC16M08S200L
8.5
16
14.5 200
10
10
M8
SC20M10S120S
10.5
20
18.5 120
10
14
M10
SC20M10S220L
10.5
20
18.5 220
10
14
M10
SC25M12S125S
12.5
25
23.5 125
10
19
M12
SC25M12S245L
12.5
25
23.5 245
10
19
M12
SC32M16S140S
17
32
28.5 140
15
24
M16
SC32M16S280L
17
32
28.5 280
15
24
M16
SC16M08S100SW
8.5
16
14.5 100
10
10
M8
SC16M08S200LW
8.5
16
14.5 200
10
10
M8
SC20M10S120SW
10.5
20
18.5 120
10
14
M10
SC20M10S220LW
10.5
20
18.5 220
10
14
M10
SC25M12S125SW
12.5
25
23.5 125
10
19
M12
SC25M12S245LW
12.5
25
23.5 245
10
19
M12
SC32M16S140SW
17
32
28.5 140
15
24
M16
SC32M16S280LW
17
32
28.5 280
15
24
M16
HOW TO INSTALL THE SCREW-IN HEAD

z Thoroughly clean the clamp section of the head and the
arbor with an air blower or brush before installation.
MILLING
x Tighten the head at the recommended torque and ensure

that there is no gap between the head and arbor.
Screw Size
Recommended Torque
Wrench Size
23
46
80
90
10
14
19
24
(N m)
M8
M10
M12
M16
(mm)
a Cutting tools become extremely hot during cutting. Never touch them with bare hands after operation as this mayproduce risk of
injuries or burns.
a Do not handle the cutting tools with bare hands as this may cause injuries.
CUTTER TYPE
ASX400
APX3000
APX4000
AQX
AJX
^ L042
^ L048
^ L054
^ L078
^ L088
ARX
SRF
SUF
SRM2
PMC
^ L099
^ L121
^ L125
^ L130
^ L140
SPARE PARTS
TECHNICAL DATA
P001
Q001
L145
INDEXABLE MILLING
Order Number
BT30
Stock
y BT30 SHANK ARBOR

Dimensions (mm)
DCB
BD
LPR
LB
CRKS
BD
DCB
CRKS
SC16M08S10-BT30
8.5
14.5
32
10
M8
SC20M10S10-BT30
10.5
18.5
32
10
M10
SC25M12S10-BT30
12.5
23.5
32
10
M12
SC32M16S10-BT30
17.0
28.5
32
10
M16
LB
LPR
Order Number
BT40
Stock
y BT40 SHANK ARBOR
BD
DCB
CRKS
Dimensions (mm)
DCB
BD
LPR
LB
CRKS
SC16M08S10-BT40
8.5
14.5
37
10
M8
SC20M10S10-BT40
10.5
18.5
37
10
M10
SC25M12S10-BT40
12.5
23.5
37
10
M12
SC32M16S10-BT40
17.0
28.5
37
10
M16
LB
LPR
HSK63A
Order Number
Stock
y HSK63A SHANK ARBOR
63
BD
DCB
MILLING
CRKS
Dimensions (mm)
DCB
BD
LPR
LB
CRKS
SC16M08S22-HSK63A
8.5
14.5
48
22
M8
SC20M10S24-HSK63A
10.5
18.5
50
24
M10
SC25M12S27-HSK63A
12.5
23.5
53
27
M12
SC32M16S28-HSK63A
17.0
28.5
54
28
M16
LB
LPR
CUTTER TYPE
ASX400
APX3000
APX4000
AQX
AJX
L146
^ L042
^ L048
^ L054
^ L078
^ L088
ARX
SRF
SUF
SRM2
PMC
^ L099
^ L121
^ L125
^ L130
^ L140
SPARE PARTS
TECHNICAL DATA
P001
Q001
FACE MILLING
V10000
<HIGH SPEED FINISHING ALUMINIUM ALLOY >
Fig.1
BD
DCON
63
KWW
APMX CBDP
a Insert with PCD.

a Light weight, strong
aluminium alloy cutter

body.
a Anti-Fly insert
mechanism enables
high speed milling.
run-out function.
KAPR :0
GAMP :+8
GAMF :+8
80
100
125
DCCB
DC
DAH
DC
Dimensions (mm)
Max.
Allowable
Revolution
Type
(Fig.)
Number
of Teeth
Stock
BD
DCON
KWW
Fig.2
DC
V10000-063A04R
63
50 22
20
11
66.1
10.4
6.3
0.5
1.5
25000
V10000R0305C
80
50 25.4
26
38
81.7
9.5
0.6
1.5
22300
V10000R0406D
100
50 31.75 32
45 100.88 12.7
0.9
1.5
20000
V10000R0508E
125
63 38.1
60 125.22 15.9 10
1.8
1.5
17800
Order Number
LF DCON CBDP DAH DCCB BD KWW L8
35
LF
L8
CBDP
N
Non-ferrous Metal
APMX
LF
L8
Finishing
WT
(kg)
APMX
(mm)
(min
-1)
* WT : Tool Weight
SPARE PARTS
Tool Holder Number

Cartridge Clamp Cartridge Clamp
Insert
Run-out
Balance
Screw-A
Screw-B
Clamp Screw Adjust Screw Adjust Screw
Cartridge
V10000-063A04R
VCT13R
HBH06016
HBH04008 CS350790T
KS1
HSS05005
V10000R0508E
Wrench
Wrench
HKY25R
HKY40R
TKY10R
* Clamp Torque (N m) : CS350790T=3.5, HBH06016=8.0, HBH04008=4.0

Work
Material
Geometry
9.5
12
NP-GDCW1240PDFR2 C
PCD
MD220
Silicon
(%)
Cutting Speed Feed per Tooth Depth of Cut

(m/min)
(mm/t.)
(mm)
6500
< 16
Aluminium
Alloy
C0.5 15 18
MILLING
Order Number

Class
INSERTS
0.2
0.5
1000
> 16
y NOTE ON ROTATIONAL BALANCE

a At the time of shipping, the cutter body is balanced by using a special high accuracy
master insert in order that it will conform to balance quality G6.3 based on ISO 1940/1
(approximate value at the maximum revolution for each cutter diameter). In order to
keep good rotational balance, do not adjust the balance screw (HSS05005) located
on the outer surface of the body.
a Rotational balance will change after exchanging cartridges. If you use the cutter at the
same revolution as that of the following table or higher, re-balancing is necessary
after exchanging cartridges. Please contact Mitsubishi Materials to re-balance the
cutter.
(Note 1) If the revolution is the same as or lower than the value indicated above, the
cutter can be used with a standard arbor. (Do not use long shank type arbors
or special arbors, as the overhang could make it dangerous to use.)
(Note 2) If the revolution is higher than the value indicated above, please set the
balance as follows : (Arbor + cutter) < G6.3
a
Balance adjust screw

Run-out adjust Screw
Cartridge set
screwB
Cartridge set
screwA
Body
Cartridge
Insert
Diameter of cutter (mm) Revolution requiring re-balancing (min-1)
63
80
100
125
17000
14500
14000
Re-balancing not necessary up to the max. revolution
SPARE PARTS
TECHNICAL DATA
P001
Q001
L147
INDEXABLE MILLING
FACE MILLING
NF10000
<For aluminium alloy and cast iron / high feed rate and finishing>
BD
DCON
KWW
Fig.1
125
CBDP
LF
80
100
BD
DCON
KWW
Fig.2
L8
a Suitable for high-
speed finishing of light

alloy and cast iron.
edge run-out function.
DAH
DC
90
CBDP
LF
N
Non-ferrous Metal
DCCB
DC
90
APMX
K
Cast Iron
APMX
L8
Finishing
Fine Pitch Coarse Pitch
Type
KAPR :0
GAMP :+10
GAMF :+5
Order Number
Stock Number
of
R Teeth DC
NF10000R0305C
80
NF10000R0406D
NF10000R0508E
NF10000R0306C
NF10000R0408D
NF10000R0510E
10
*2
Dimensions (mm)
WT
(kg)
LF DCON CBDP DAH DCCB BD KWW L8
50 25.4
80.2
1.0
4.0
1.0
100
63 31.75 32
17
100.2 12.7
1.8
4.0
1.0
14000
125
63 38.1
38
60 125.2 15.9
10
2.7
4.0
1.0
12000
80
50 25.4
26
13
1.0
4.0
1.0
16000
100
63 31.75 32
17
100.2 12.7
1.8
4.0
1.0
14000
125
63 38.1
60 125.2 15.9
10
2.7
4.0
1.0
12000
9.5
CBN
13
80.2
9.5
PCD
Max. 1
Allowable Type
Revolution (Fig.)
(min-1)
26
38
APMX (mm)
16000
max. spindle speed is achieved under the conditions that the cutter is clamped by a machine clamping force of 18kN with a
*1 Ensure
standard type arbor. (HSK 63A-FMAppp-60) The figure varies in actual machining depending on cutting conditions, such as the length of
overhang or if there is insufficient drawing force from the arbor.
*2 WT : Tool Weight
INSERTS
SPARE PARTS
MB730
Geometry
12.7
MILLING
Clamp Screw
Wrench
CWAF10R1
LS10T
TKY25T
NF10000R0510E

20
Wedge
NF10000R0305C
R1.2
NP-GDCN2004PDSR3
Tool Holder Number
GDCN2004PDFR3
MD220
Order Number
Class
PCD CBN
20
4.76
12.7
R0.8
20
10
4.76

N
K
Work Material
Grade
Aluminium Alloy
MD220
3500 (1000 4500)
0.12 ( 0.05 0.20)
Gray Cast Iron
MB730
1000 (800 1500)
0.15 (0.05 0.5)

a
L148
SPARE PARTS
TECHNICAL DATA
P001
Q001
FACE MILLING
FF3000
<GENERAL HIGH FEED FINISHING>
Finishing
H
125
160
a 1000 3000mm/min
BD
DCON
KWW

a For finishing of steel
18
DCCB
DC
DCX
APMX
DCCB
DC
DCX
machining.
run-out function.
BD
Fig.2 101.6
200 DCON
250 KWW
LF
Fig.1
L8
CBDP
N
Non-ferrous Metal
APMX
K
Cast Iron
35
M
Stainless Steel
L8
CBDP
LF
P
Steel
KAPR :0
GAMP :+5 T :+15
GAMF :-15 I :+5
Stock Number
R of Teeth
Order Number
DCX
LF
DCON CBDP DCCB
140.4
75
38.1
KWW
L8
WT
(kg)
APMX
(mm)
Type
(Fig.)
132.8 15.9
10
5.8
0.3
BD
FF3000R0502E
125
FF3000R0602F
160
175.4
75
50.8
38
80
165.6 19.1
11
9.0
0.3
FF3000R0802K
200
215.4
75
47.625
45
134
204.1
25.4
14
12.6
0.3
FF3000R1002K
250
265.4
75
47.625
45
182
252.8 25.4
14
19.5
0.3
38
60
WT : Tool Weight
INSERTS

Work
Material
Hardness
Grade
P Mild Steel
< 180HB
NX2525 (SPCG)
NX2525
SPCA53Z
11
15.88
4.8
11
15.88
4.8
Work Material
HTi05T
Order Number
Work Material
Geometry
Class
Cermet Carbide

(m/min)
(mm/t.)
Carbon Steel 180 280HB NX2525 (SPCG)

Alloy Steel
High Alloy Steel 200280HB NX2525 (SPCA)
Steel
Stainless Steel
Cast Iron
Aluminium Alloy
SPCG53Z
M Stainless Steel
K
Cast Iron
Steel
Stainless Steel
Cast Iron
Aluminium Alloy
N Aluminium
< 200HB
NX2525 (SPCA)
Tensile
Strength
< 450MPa
NX2525 (SPCG)
HTi05T
HTi05T
280
(250300)
180
(150220)
120
(80150)
250
(230280)
180
(130200)
120
(100150)
2.25
(2 2.5)
2.25
(2 2.5)
2.25
(22.5)
3.0
(2.53.5)
2.25
(2 2.5)
0.85
< 500
(0.7 1.0)
Alloy
-1
a Revolution (min )=(1000 x Cutting Speed)u(3.14 x DC)
MILLING
Dimensions (mm)
DC
e : 1st Recommendation, u : 2nd Recommendation, : No recommendations
SPARE PARTS
Tool Holder
Number
FF3000R0502E
FF3000R1002K
Cartridge
Shim
Lock Pin
Cartridge
Clamp Screw
Washer
Radial Spring
FFCSR
FFSS
FFP
HBH08040
FFW
FFRP
z
Tool Holder
Number
FF3000R0502E
FF3000R1002K
Adjusting Wedge
Adjusting Screw
Lever
Lever Screw
Axial Spring
Wrench
FFAWR
LS3
FFL
FFLB
HP3
zHKY25L
xHKY40T
* Clamp Torque (N m) : FFP=2.2, HBH08040=9.5

a
SPARE PARTS
TECHNICAL DATA
P001
Q001
L149
INDEXABLE MILLING
QUICK CHANGE TYPE

FP490
200
250
315
355
400
500
a Suitable for cast iron
DC
finishing.
Type
Quick Change Q Type
Quick Change
T Type
DC
Fig.3
a Multi insert design.

a For high feed cutting.
T type
BDX
250
315
355
400
DCON
DC
T :+5
I :0
Order Number
APMX
KAPR :0
GAMP :+5
GAMF :+0
LCCB
80
100
125
160
Cast Iron
BDX
DCON
LF
APMX
LF
Q type
(Large
Diameter)
L8
LCCB
Fig.2
Q type
BDX
(Small
DCON KWW
Diameter)
LF
Fig.1
APMX
Finishing
Dimensions (mm)
Number
of Teeth
DC
BDX
LF
DCON LCCB KWW
L8
WT
(kg)
APMX
(mm)
Installation Detail
Dimensions
Type
(Fig.)
FP490R/L0308Q
80
85
50
25.4
26
10.8
1.5
0.5
FP490R/L0410Q
10
100
105
63
31.75
29
12.8
2.8
0.5
FP490R/L0514Q
14
125
130
63
38.1
29
15.8
4.2
0.5
FP490R/L0618Q
18
160
165
63
29
18.8
6.7
0.5
FP490R/L0822Q
22
200
205
45
125
25
5.5
0.5
FP490R/L1028Q
28
250
255
45
175
25
8.0
0.5
FP490R/L1236Q
36
315
320
45
240
25
10.7
0.5
FP490R/L1440Q
40
355
360
45
280
25
12.2
0.5
FP490R/L1646Q
46
400
405
45
325
25
13.8
0.5
FP490R/L2056Q
56
500
505
45
425
25
17.8
0.5
FP490R/L1028T
28
250
260
45
110
9.8
0.5
FP490R/L1236T
36
315
325
45
175
12.1
0.5
FP490R/L1440T
40
355
365
45
215
14.1
0.5
FP490R/L1646T
46
400
410
45
260
15.4
0.5
50.8
1
1
Refer to page M014.

(Q Type& 80 & 160)
Refer to page M015.

(Q Type& 200 & 500)
Refer to page M015.

(T Type& 250 & 400)
2
2
3
3
3
(Note) These are produced to order only.

WT : Tool Weight
Order Number
SPEN424A

Class
INSERTS
Carbide
HTi10
HTi05T
MILLING
Work
Material
Geometry
K Gray Cast
Iron
a a
R1.6
Grade
< 350MPa
HTi05T

(m/min)
(mm/t.)
125
(100 150)
0.2
(0.1 0.3)

11
12.70
Tensile
Strength
3.18
SPARE PARTS
*
Tool Holder
Number
Wedge
Clamp Screw
Wrench
CWS42SPR/L
LS14
HKY40T
FP490R/L0308Q
FP490R/L1646T
Hexagonal Head
Wrench
(Sold Separately) (Sold Separately)
120QSPK80
6.35r4
(KANONN-SEIKI CO.) (KYOKUTO MFG CO.)

a
L150
SPARE PARTS
TECHNICAL DATA
P001
Q001
125
160
Cast Iron
a Suitable for cast iron
DC
finishing.
Type
Quick Change Q Type
Quick Change
T Type
DCON
200
250
315
355
400
500
DC
Fig.3
a Multi insert design.

a For high feed cutting.
KAPR :0
GAMP :+5
GAMF :+0
BDX
LCCB
LF
DCON KWW
APMX
Q type
(Large
Diameter)
BDX
T type
BDX
250
315
355
400
DCON
APMX
LF
Fig.2
Q type
(Small
Diameter)
L8
LCCB
Fig.1
LF
Finishing
APMX
QUICK CHANGE TYPE

FP590
DC
T :+5
I :0
Dimensions(mm)
Order Number
Number
of Teeth
DC
BDX
LF
FP590R/L0514Q
14
125
135
63
FP590R/L0618Q
18
160
170
63
FP590R/L0822Q
22
200
210
45
125
FP590R/L1028Q
28
250
260
45
175
FP590R/L1236Q
36
315
325
45
240
DCON LCCB KWW
38.1
50.8
L8
WT
(kg)
APMX
(mm)
Installation Detail
Dimensions
Type
(Fig.)
4.2
0.5
Refer to page M014.

(Q Type& 125 & 160)
29
15.8
29
18.8
6.7
0.5
25
5.5
0.5
25
8.0
0.5
25
10.7
0.5
Refer to page M015.

(Q Type& 200 & 500)
FP590R/L1440Q
40
355
365
45
280
25
12.2
0.5
FP590R/L1646Q
46
400
410
45
325
25
13.8
0.5
FP590R/L2056Q
56
500
510
45
425
25
17.8
0.5
FP590R/L1028T
28
250
260
45
110
9.8
0.5
FP590R/L1236T
36
315
325
45
175
12.1
0.5
FP590R/L1440T
40
355
365
45
215
14.1
0.5
FP590R/L1646T
46
400
410
45
260
15.4
0.5
Refer to page M015.

(T Type& 250 & 400)
3
3
3

WT : Tool Weight

Work
Material
SPEN535A
Geometry
HTi05T
Order Number
Class
Carbide
K Gray Cast
Iron
Tensile
Strength
Grade
< 350MPa
HTi05T

(m/min)
(mm/t.)
125
(100150)
0.2
(0.1 0.3)
MILLING
INSERTS

R2.0

11
15.875
4.76
SPARE PARTS
*
Tool Holder
Number
Wedge
Clamp Screw
Wrench
CWS5
LS14
HKY40T
FP590R/L0514Q
FP590R/L1646T
Hexagonal Head
Wrench
120QSPK80
6.35r4

a
SPARE PARTS
TECHNICAL DATA
P001
Q001
L151
INDEXABLE MILLING
QUICK CHANGE TYPE

FE404
<FINISHING FOR ALUMINIUM ALLOY>
100
125
160
Non-ferrous Metal
a High rake and relief angle.
a Suitable for light alloy
L8
LCCB
4
DC
DCX
Type
DC
DCX
T type
DCON
250
315
355
400
4
APMX
DC
DCX
KAPR :4
GAMP :+11 T :+10
GAMF :+9 I :+10
Quick Change Q Type
200
250
315
355
400
500
Fig.3
machining.
Quick Change
T Type
DCON
LCCB
LF
Q type
(Large
Diameter)
APMX
Fig.2
LF
DCON KWW
Q type
(Small
Diameter)
LF
Fig.1
APMX
Finishing
Dimensions(mm)
L8
WT
(kg)
APMX
(mm)
12.8
3.2
29
15.8
4.7
29
18.8
7.6
125
25
6.1
175
25
7.8
45
240
25
10.2
45
280
25
11.8
402
45
325
25
13.3
502
45
425
25
16.2
250
251
45
110
9.9
315
316
45
175
12.2
28
335
356
45
215
13.7
32
400
401
45
260
16.2
Order Number
Number
of Teeth
DC
DCX
LF
FE404R/L0408Q
100
102
63
31.75
29
FE404R/L0510Q
10
125
127
63
38.1
FE404R/L0612Q
12
160
162
63
50.8
FE404R/L0816Q
16
200
202
45
FE404R/L1020Q
20
250
252
45
FE404R/L1224Q
24
315
317
FE404R/L1428Q
28
355
357
FE404R/L1632Q
32
400
FE404R/L2040Q
40
500
FE404R/L1020T
20
FE404R/L1224T
24
FE404R/L1428T
FE404R/L1632T
DCON LCCB KWW
Installation Detail
Dimensions
Type
(Fig.)
Refer to page M014.

(Q Type& 100 & 160)
Refer to page M015.

(Q Type& 200 & 500)
Refer to page M015.

(T Type& 250 & 400)
1
1
1
2
2
3
3
3

WT : Tool Weight
INSERTS

Work
Material
Class
Order Number
Geometry
HTi10
MILLING
Carbide
SEA42C10GR
SEA42C10GL
Silicon
(%)
Grade

(m/min)
(mm/t.)
< 10
HTi10
700
0.15
(4001000) (0.05 0.25)
> 10
HTi10
400
(200600)
Aluminium
Alloy
2.4
21
12.70
3.18
0.15
(0.05 0.25)

(Note) Use R at a right hand body and L at a left hand body.
SPARE PARTS
*
Tool Holder
Number
Wedge
Clamp Screw
Wrench
CWS42SER/L
LS10
HKY40T
FE404R/L0408Q
FE404R/L1632T
Hexagonal Head
Wrench
120QSPK80
6.35r4

L152
SPARE PARTS
TECHNICAL DATA
P001
Q001
SHOULDER
MILLING
Roughing
BAP300
K
Cast Iron
DCON
M
Stainless Steel
DC
P
Steel
APMX
a Inserts with wiper edges produce
LH
LF
optimal finished surface.

a Multi insert design for high feed machining.
LF
DCON
LH
APMX
Clamp
Screw
Wrench
10
85
16
25
TS25
TKY08F
12
85
16
25
TS25
TKY08F
BAP300R141S16
14
85
16
25
TS25
TKY08F
BAP300R162S16
16
85
16
25
TS25
TKY08F
BAP300R182S16
18
85
16
25
TS25
TKY08F
BAP300R203S20
20
100
20
30
TS25
TKY08F
BAP300R223S20
22
100
20
30
TS25
TKY08F
BAP300R254S25
25
115
25
35
TS25
TKY08F
BAP300R284S25
28
115
25
35
TS25
TKY08F
BAP300R304S32
30
125
32
45
TS25
TKY08F
BAP300R325S32
32
125
32
45
TS25
TKY08F
BAP300R406S32
40
125
32
45
TS25
TKY08F
BAP300R507S32
50
125
32
45
TS25
TKY08F
BAP300R638S32
63
125
32
45
TS25
TKY08F
BAP300R202LS20
20
150
20
60
TS25
TKY08F
BAP300R253LS25
25
170
25
70
TS25
TKY08F
BAP300R323LS32
32
190
32
90
TS25
TKY08F
BAP300R403LS32
40
190
32
90
TS25
TKY08F
BAP300R101S16
BAP300R121S16
Dimensions(mm)
Insert
APG/MT1135PDpR-pp
MILLING
Number of Teeth
Standard
DC
Order Number
Long

Stock
Type
y SHANK TYPE
APG/MT1135PDpR-pp
SPARE PARTS
TECHNICAL DATA
P001
Q001
L153
INDEXABLE MILLING
INSERTS
Steel

: Stable Cutting
: General Cutting
Stainless Steel
Non-ferrous Metal
Honing :
E : Round F : Sharp
NX2525
NX4545
HTi10
Dimensions(mm)
Class
Honing
F7030
VP15TF
Cermet Carbide
L
APMT1135PDER-H1
M E
a a
a a a
11
6.35 3.5 1.5 0.4
APMT1135PDER-H2
M E
a a
a a a
11
6.35 3.5 1.2 0.8
APMT1135PDER-H3
M E
11
6.35 3.5 0.8 1.2
APMT1135PDER-H4
M E
11
6.35 3.5 0.4 1.6
APMT1135PDER-H6
M E
11
6.35 3.5 0.4 2.4
APMT1135PDER-M0
M E
11
6.35 3.5 1.8 0.2
APMT1135PDER-M1
M E
11
6.35 3.5 1.5 0.4
APMT1135PDER-M2
M E
a a
11
6.35 3.5 1.2 0.8
Order Number
W1
BS
Geometry
RE
RE
85
G F
11
6.35 3.5 1.2 0.8
11
S
RE
BS
W1
11
S
RE
85
APGT1135PDFR-G2
W1
Hardened Steel
BS
Coated
Shape
: Unstable Cutting
Cast Iron
BS
W1
Work
Material
P
M
K
N
S
H
85
11
S

Work Material
Mild Steel
Hardness
NX4545
< 180HB
180 280HB
Carbon Steel
Alloy Steel
MILLING
280 350HB
Stainless Steel
Gray Cast Iron

Ductile Cast Iron
( < JIS FCD450)
Ductile Cast Iron
( > JIS FCD500)
Grade
< 200HB
Tensile Strength
< 350MPa
Tensile Strength
< 450MPa
Tensile Strength
500 800MPa
Cutting Speed
(m/min)
Feed per Tooth

(mm/t.)
Finish Cutting
160 (120180)
0.1 (0.05 0.15)

0.15 (0.1 0.2)
Breaker Cutting Mode

H
F7030
General Cutting
180 (150200)
NX4545
Finish Cutting
120 (100160)
0.08 (0.05 0.1)

0.15 (0.1 0.2)
F7030
General Cutting
150 (120200)
F7030
Unstable Cutting
120 (100160)
0.15 (0.1 0.2)
NX4545
Finish Cutting
100 (80120)
0.08 (0.05 0.1)
F7030
General Cutting
140 (120160)
0.15 (0.1 0.2)
F7030
Unstable Cutting
100 (80120)
F7030
General Cutting
140 (120160)
F7030
Unstable Cutting
120 (80140)
VP15TF
General Cutting
140 (120160)
HTi10
General Cutting
120 (100140)
VP15TF
General Cutting
120 (100140)
HTi10
General Cutting
100 (80120)
0.2 (0.1 0.25)

0.1 (0.05 0.15)
0.15 (0.1 0.2)
VP15TF
General Cutting
100 (80120)
HTi10
General Cutting
80 (60100)
0.2 (0.1 0.25)

0.15 (0.1 0.2)
0.2 (0.1 0.25)
0.15 (0.1 0.2)
Aluminium Alloy
HTi10
General Cutting
500 (2001000)
0.2 (0.1 0.3)
Ti Alloy
> 350HB
HTi10
General Cutting
40 (3060)
0.2 (0.1 0.3)
F7030
General Cutting
30 (2040)
0.15 (0.1 0.2)
Hardened Steel
> 40HRC
VP15TF
General Cutting
70 (50100)
0.1 (0.050.15)

-1)

L154
0.2 (0.1 0.25)

0.15 (0.1 0.2)
Shoulder Milling
10
fz=
0.1
fz=
0.1
5
0.5DC
Cutting Width
DC
Cutting Depth (mm)
Cutting Depth
a &16 &100
10
fz fz=0
=0
.1
0.2 .15
fz=
fz=
0.2
DC
0.5DC
Cutting Width
Slot Milling
a & 10 & 14
a & 16 & 100
10
DC
=
1
DC 2
= 14
10
0.1
0.2
3
0...3
Cutting Depth (mm)

Grade : F7030
Cutting Depth (mm)
DC
Cutting Depth
Cemented carbide/Coated carbide

Grade : F7030
Cutting Depth (mm)
a & 10 &14
Cutting Width
10
Feed fz (mm/t.)
DC DC=
DC =25 50
100
=
16
40
22
0.1
0.2
Feed fz (mm/t.)
0..3
Shoulder Milling
a & 16 & 100
10
10
fz=
0.1
fz=
0.15
Cutting Depth (mm)
Cutting Depth
Cermet

Grade : NX2525
Cutting Depth (mm)
a & 10 & 14
Cutting Width
0.5DC
Cutting Width
DC
fz=
0.1
fz=
0.15
0.5DC
Cutting Width
DC
MILLING
(Note 1) In each of the adove graphs cutting performance is shown for carbon steel (JIS S50C).
In case of alloy steels, reduce the conditions by 20 30%.
(Note 2) In the case of deep slot milling, air blow should be used.
(Note 3) The diameter DC is taken from the tools peripheral cutting edge.
SPARE PARTS
TECHNICAL DATA
P001
Q001
L155
INDEXABLE MILLING
DEEP SHOULDER
MILLING
Roughing
BAP300
K
Cast Iron
DCON
M
Stainless Steel
DC
P
Steel
LONG CUTTING EDGE
APMX
LH
a Inserts with wiper edges
LF
produce optimal finished surface.

a Multi insert design for high feed
machining.
Total
Number of Flutes
Order Number
DC
LF
DCON
LH
20
120
20
40
25
TS25
TKY08F
25
130
25
50
34
TS25
TKY08F
12
32
140
32
60
43
TS25
TKY08F
14
40
150
42
70
51
TS25
TKY08F
Stock
y SHANK TYPE
BAP300R2004ES20
BAP300R2508ES25
BAP300R3212ES32
BAP300R4014ES42
Dimensions(mm)
APMX Clamp Screw
Wrench
Insert
APG/MT1135
PDpR-M0/p1/p2

INSERTS
Dimensions(mm)
NX2525
NX4545
HTi10
Order Number
Cermet Carbide
L
APMT1135PDER-H1 M E
a a
a a a
11
6.35
3.5
1.5
0.4
APMT1135PDER-H2 M E
a a
a a a
11
6.35
3.5
1.2
0.8
W1
BS
RE
Geometry
RE
W1 BS
MILLING
Shape
Class
Honing
F7030
VP15TF
Coated
85
APMT1135PDER-M1 M E
APMT1135PDER-M2 M E
a a
11
6.35
3.5
1.8
0.2
11
6.35
3.5
1.5
0.4
11
6.35
3.5
1.2
0.8
RE
BS
W1
APMT1135PDER-M0 M E
85
11
L
G F
11
6.35
3.5
1.2
S
RE
0.8
BS
W1
APGT1135PDFR-G2
11
S
11
85
L

L156

Work Material
Mild Steel
Cutting Speed
(m/min)
Feed per Tooth

(mm/t.)
General Cutting
180
(150200)
0.15
(0.08 0.2)
General Cutting
150
(120280)
0.15
(0.08 0.2)
F7030
Unstable Cutting
120
(100160)
0.2
(0.10.25)
F7030
General Cutting
F7030
Unstable Cutting
140
(120160)
100
(80120)
0.1
(0.050.15)
0.15
(0.080.2)
F7030
General Cutting
F7030
Unstable Cutting
140
(120160)
120
(80140)
0.1
(0.080.15)
0.15
(0.080.2)
VP15TF
General Cutting
HTi10
General Cutting
140
(120160)
120
(100140)
VP15TF
General Cutting
UTi20T
General Cutting
0.15
(0.08 0.2)
0.1
(0.050.15)
0.1
(0.050.15)
0.15
(0.080.2)
VP15TF
General Cutting
HTi10
General Cutting
Hardness
Grade
< 180HB
F7030
F7030
Breaker Cutting Mode
180 280HB
Carbon Steel
Alloy Steel
280 350HB
M
Stainless Steel
K
Gray Cast Iron
Ductile Cast Iron
Ductile Cast Iron
< 200HB
Tensile Strength
< 350MPa
Tensile Strength
< 450MPa
Tensile Strength
500 800MPa
Aluminium Alloy
HTi10
General Cutting
Ti Alloy
> 350HB
HTi10
General Cutting
F7030
General Cutting
Hardened Steel
> 40HRC
VP15TF
General Cutting
120
(100140)
100
(80120)
100
(80120)
80
(60100)
40
(3060)
30
(2040)
0.08
(0.050.1)
0.1
(0.050.15)
0.15
(0.050.25)
0.15
(0.05 0.25)
0.1
(0.05 0.15)
70
(50100)
0.08
(0.050.1)
500
(2001000)
MILLING

SPARE PARTS
TECHNICAL DATA
P001
Q001
L157
INDEXABLE MILLING
Slot Milling
Cutting Depth
Cutting Width
DC

Grade : F7030
50
40
30
Cutting Depth (mm)

Grade : F7030
Cutting Depth (mm)
Cemented carbide/Coated carbide
Shoulder Milling
DC=40
DC=32
DC=25
20 DC=20
10
0
0.5DC
Cutting Width
DC
50
40
30 DC=40
DC=32
20
DC=25
10
DC=20
0
MILLING
(Note 1) In each of the adove graphs cutting performance is shown for carbon steel (JIS S50C).
In case of alloy steels, reduce the conditions by 20 30%.
(Note 2) In the case of deep slot milling, air blow should be used.
(Note 3) The diameter DC is taken from the tools peripheral cutting edge.
L158
Cutting Depth
0.1
0.2
Feed fz (mm/t.)
0.3
SETTING FIXTURE
FEATURES OF SETTING FIXTURE
a Compact design.
a Easy set up operation.
a Insert is adjusted from the cutting edge
point therefore run-out accuracy is high.
h1
100
Jig or Fixture Surface
30 85
SETTING FIXTURE STANDARD
h1
SEF500
SEF700
315
600
400
347
247
Cutter Diameter (Note 1) Please specify the order number when ordering.
&500 (Note 2) Please contact us regarding special spare parts order.
400
800
500
360
260
&315 &700
Needle
Height Gauge
zSet the needle using a height

gauge which is the same height
as the cutter.
3
1
xMove the needle to an insert.
Torque Wrench
bScrew the inserts tightly

according to the picture shown
on the left.
cSlide the insert to the point

where it touches the needle
Tighten all the inserts lightly.
(Use torque wrench.) (12N m)
Cutter
vAfter temporary tightening, use a

torque wrench to tighten firmly.
(Use torque wrench.) (8 N m)
Dial Gauge
the inserts too tightly
*Screwing
results in lower accuracy.
MILLING
Method of Insert Setting for Two Piece Type. Method of Insert Setting for One Piece Type.
Order Number
nCheck run-out of all the inserts

with a dial gauge.
For general milling, 10!m is the
*standard.
For finishing,set the insert
<
run out at<5!m.
Height Gauge
zSet the height gauge at the same

height as the cutter on the liners
of slider, then set the needle.
xPut the cutter on the liners of the
slider and move the rollers of the
slider to the installation holes.
Slider
cMake sure that the three rollers

are free, then fix the sliders.
Process of tightening the inserts is
*the
same as the one piece type.
aNote
1. After machining, dust off chips on the cutter with air before
loosening the wedge.
2. When loosening clamp screws, avoid using a damaged
wrench.
3. Alien substances attached to inserts lowers run-out
accuracy and damages the cutter body. Therefore, they
need to be cleaned throughly.
4. After all the inserts are taken out, clean the cutter body with
oil or strong air blow.
5. Use a torque wrench or special wrench for tightening the
clamp screws.
L159
INDEXABLE MILLING
Qing SYSTEM
STRUCTURE CHIP COLLECTION

METHOD
STRUCTURE
a Automatic continuous intake of chips while machining.
a Eliminates chip handing problems.
Chip Flow Direction
1
Cutting is performed by a face mill.
Casing
Chip Flow Area
2
Chips are directed into the casing
by way of the chip guide plate.
Suction Unit
3
Discharge Port
Cutter
Insert
Chip Guide Plate
y CHIP COLLECTION METHOD
Self Expulsion Type QMC

zChips are discharged towards the chip conveyor because of the centrifugal
force created by the cutter.
xInstallation with an ATC(auto tool changer) on machining centers is possible.
cSince there is no need for air or a dust collector, this method provides the
lowest initial investment and running costs.
vChips cannot be transported (carried) directly over long distances.
bHigh speed bearing required to suit high speed machining.
Double Air Type QWA

MILLING
zChip recovery using compressed air (factory air).

xSince air is also injected into the casing interior, wet cutting is also possible.
cAchieves the same suction capabilities as a dust collector, thereby enabling
low equipment costs.
vWet cutting is not recommended.
Vacuum Machine Type QSV

zChip collection by use of a suction machine.
xChip collection efficiency is high.
cSpecial equipment is required, such as a mist collector for wet cutting.
L160
Chips are expelled via the discharge port.
MAXIMUM ALLOWABLE REVOLUTION

FOR CUTTER
WSX445
Max.
Max.
Clamp
Clamp
Allowable Torque Allowable Torque
Revolution
Revolution
(N m)
(N m)
(min-1)
(min-1)
40
19000
3.5
50
17000
3.5
18000
3.5
63
15000
3.5
16000
3.5
80
14000
3.5
14000
3.5
100
12000
3.5
13000
3.5
125
11000
3.5
12000
3.5
160
9500
3.5
10000
3.5
200
8500
3.5
9000
3.5
250
8000
3.5
315
6500
3.5
AHX640S
Diameter
(mm)
40
AHX640W
AOX445
ASX400
SE515
Max.
Max.
Max.
Max.
Max.
Clamp
Clamp
Clamp
Clamp
Clamp
Allowable Torque Allowable Torque Allowable Torque Allowable Torque Allowable Torque
Revolution
Revolution
Revolution
Revolution
Revolution
(N m)
(N m)
(N m)
(N m)
(N m)
(min-1)
(min-1)
(min-1)
(min-1)
(min-1)
50
13000
18000
3.5
63
12000
12000
16000
3.5
80
10000
8900
11000
14000
3.5
100
8700
7800
9300
13000
3.5
9300
125
7500
6600
8300
12000
3.5
8100
160
6100
5300
7200
10000
3.5
7000
200
5100
4100
6400
9000
3.5
250
2900
8000
3.5
315
1700
AXD4000
Diameter
(mm)
AXD7000
BXD4000
V10000
SG20
Max.
Max.
Max.
Max.
Max.
Clamp
Clamp
Clamp
Clamp
Clamp
Allowable Torque Allowable Torque Allowable Torque Allowable Torque Allowable Torque
Revolution
Revolution
Revolution
Revolution
Revolution
(N m)
(N m)
(N m)
(N m)
(N m)
(min-1)
(min-1)
(min-1)
(min-1)
(min-1)
20
15000
1.5
15000
25
49000
1.5
38000
28
48500
1.5
32
48000
1.5
41000
3.5
33000
35
45000
1.5
31000
40
41000
1.5
36000
3.5
29000
50
35000
1.5
30000
3.5
24000
63
30000
1.5
25000
3.5
21000
25000
3.5
80
27000
1.5
23000
3.5
19000
22300
3.5
8200
100
23000
1.5
19000
3.5
16000
20000
3.5
7000
125
20000
1.5
16000
3.5
14000
17800
3.5
6100
160
5300
MILLING
Diameter
(mm)
ASX445
(Note) All values shown on this chart are based on the insert being properly seated in pocket and
torqued to the recommended values.
a For APX3000, please refer to page L046 and L047.
a For APX4000, please refer to page L052 and L053.
L161
INDEXABLE MILLING
LIST OF CUTTING
EDGE DIAMETER TOLERANCES
Milling
Cutting edge diameter tolerance
(mm)
Milling
Cutting edge diameter tolerance
(mm)
APX3000
Arbor Type
0.1
0.4
VOX400
Arbor Type
0.1
0.4
APX3000
Shank Type
0.1
0.2
ASX400
0
0.3
APX4000
Arbor Type
0.1
0.4
AJX
0.1
0.4
APX4000
Shank Type
0.1
0.2
AQX
0.1
0.3
AXD4000
Arbor Type
0.1
0.4
SPX
0.1
0.3
AXD4000
Shank Type
0.1
0.2
OCTACUT
0
0.3
AXD7000
Arbor Type
0.1
0.4
BRP
0.1
0.3
AXD7000
Shank Type
0.1
0.2
ARX
0.05
0.15
BXD4000
Arbor Type
0.1
0.4
SRM
0.05
0.15
BXD4000
Shank Type
0.1
0.2
SRF
0
0.027
VFX5
Shell Type
0.1
0.3
PMR
0
0.3
VFX6
Shell Type
0.1
0.3
PMF
0
0.3
MILLING
(Note 1) Cutting edge diameter tolerance when the gauge insert is set.
(Note 2) When setting the insert available, the insert tolerance is added to the above tolerance. (Tolerance when setting the insert for SRF.)
L162
Memo
L163

OF TOOLING SYSTEM
zOrganized by product series. (Refer to the index on the next page.)
TYPE/
NAME OF PRODUCT
PRODUCT CATEGORY
PRODUCT SECTION
GEOMETRY
TOOLING SYSTEM
Clamp Screw
Insert
Cartridge
Lever
Shim
a Negative insert.
a Large breaker selection.
a Suitable for steel and cast iron.
Clamp
Structure
P Lever Lock
Insert Shape
C 80Rhombic
Square
S
T Triangle
Cutting Angle
90
F
G 90(Off Set)
K
75
L
95
S
45
T
60
Y
85
Shim Pin
Insert
Clearance
N
10
Hand of Tool
R Right Hand
L Left Hand
CA
11
10
12
16
20
Cartridge
10
Order Number
Stock
Geometry
PTFN
PTFNR/L10CA11
PTFNR/L12CA16
PTFNR/L16CA16
PTFNR/L20CA22
Dimensions(mm)
Insert Number
R L
20
11
09 16
LLSSN
LF MHD ASP S10 MHH HF WF RE DMIN
Shim
Shim Clamp Lever

Clamp
Pin
Lever Spring Screw
LLCL12S HLS1 LLCS105
20
20
8 2
8 2
5
6
10
12
14 0.4 40
20 0.8 50
1604pp
16
17
63
25
8 2.5
16
25 0.8 60
2204pp
20
19
70
30 10 2.5
20
25 0.8 70
1604pp
1604pp
15.5 16
16
17
55
63
20
25
8 2
8 2.5
12
16
20 0.8 50
25 0.8 60
LLSTN32 LLP13 LLCL13
0903pp
1204pp
1204pp
12.5 11
15.5 16
16
17
50
55
63
20
20
25
8 2
8 2
8 2.5
5
6
10
12
16
14 0.8 40
20 0.8 50
25 0.8 60
LLSSN42 LLP14 LLCL14
1204pp
1204pp
1204pp
15.5 16
16
17
20
19
55
63
70
20 8 2
25 8 2.5
30 10 2.5
12
16
20
20 0.8 50
25 0.8 60
25 0.8 70
0903pp
1204pp
1204pp
12.5 11
15.5 16
16
17
44
47
53
20
20
25
8 2
8 2
8 2.5
5
6
10
12
16
14 0.8 40
20 0.8 50
25 0.8 60
1604pp
1604pp
15.5 16
16
17
55
63
20
25
8 2
8 2.5
12
16
13 0.8 50
15 0.8 60
0903pp
1204pp
1204pp
12.5 11
15.5 16
16
17
50
55
63
20
20
25
8 2
8 2
8 2.5
5
6
10
12
16
14 0.8 40
20 0.8 50
25 0.8 60
a
a
PTGNR/L12CA16
PTGNR/L16CA16
PSKNR/L10CA09
PSKNR/L12CA12
PSKNR/L16CA12
PCLNR/L12CA12
PCLNR/L16CA12
PCLNR/L20CA12
PSSNR/L10CA09
PSSNR/L12CA12
PSSNR/L16CA12
PTTNR12CA16
PTTNR16CA16
PSYNR10CA09
PSYNR12CA12
PSYNR16CA12
TNMA
TNMG
TNMM
TNGA
TNGG
9.525
LLSTN
50
55
6.35
12.5 11
15.5 16
Inscribed
Circle
12 12 22 12.7
1103pp
1604pp
Cutting Edge
Length (mm)
Insert Shape
16
12
LLSCN
Type
Tool Type
CA ISO A Type
Cutting Edge
Height (mm)
Square
y IDENTIFICATION
Lever lock type
Lever lock type
80
Rhombic
LL ISO type
Triangle
CARTRIDGE
Radial Axial Wrench

Set Bolt
Screw Screw
LLR1 KS1 zHKY25R
xHKY20F HSC06016
HLS2
LLCS105
LLR1
KS1
LLCS106
LLR1
KS2
zHKY25R
xHKY20F
zHKY25R
xHKY20F
LLCS108S LLR2
KS2
zHKY30R HBH08030
HLS2
LLCS105
LLR1
KS1
LLCS106
LLR1
KS2
zHKY25R
xHKY20F
zHKY25R
xHKY20F
HSC06020
HSC06016
LLCL13S
LLCL13S
HSC06020
HBH08025
HBH08025
PTGN
PSKN
SNMA
SNMG
SNMM
SNGA
SNGG
LLCL13S
HLS2
LLCS105
LLR1
KS1
LLCL14S
HLS3
LLCS106S LLR1
KS1
zHKY20R
zHKY25R
zHKY25R
xHKY20F
LLCS108S LLR2
KS2
zHKY30R HBH08025
HSC06020
PCLN
CNMA
CNMG
CNMM
CNGG
HLS3
LLCS106S LLR1
KS1
zHKY25R
xHKY20F
LLSCN42 LLP14 LLCL14
LLCS108S LLR2
KS2
zHKY30R HBH08025
LLCS108S LLR2
KS2
zHKY30R HBH08030
LLCL14S
HSC06020
SNMA
SNMG
SNMM
SNGA
SNGG
LLCL13S
HLS2
LLCS105
LLR1
KS1
LLCL14S
HLS3
LLCS106S LLR1
KS1
zHKY20R
zHKY25R
zHKY25R
xHKY20F
LLCS108S LLR2
KS2
zHKY30R HBH08025
HLS2
LLCS105
LLR1
KS1
LLCS106
LLR1
KS2
zHKY25R
xHKY20F
zHKY25R
xHKY20F
HSC06020
HSC06016
HSC06016
HSC06020
TOOLING
TOOLING
PSSN
TNMA
TNMG
TNMM
TNGA
TNGG
PTTN
LLCL13S
HBH08025
PSYN
SNMA
SNMG
SNMM
SNGA
SNGG
a
a
LLCL13S
HLS2
LLCS105
LLR1
KS1
LLCL14S
HLS3
LLCS106S LLR1
KS1
zHKY20R
zHKY25R
zHKY25R
xHKY20F
LLCS108S LLR2
KS2
zHKY30R HBH08025
HSC06020
* Clamp Torque (N m) : LLCS105=1.5, LLCS106=2.2, LLCS106S=2.2, LLCS108S=3.3

CNpp type inserts
SNpp type inserts
a
TNpp type inserts
M002
SPARE PARTS
LEGEND FOR
STOCK STATUS MARK
REFERENCE PAGE FOR

APPLICABLE INSERTS

spread.

PRODUCT STANDARDS
stock status (per right/left hand), applicable
inserts, dimensions, minimum cutting
diameters, standard corner radius,
and spare parts.

M000
A092 A097
A105 A109
A110 A115
P001
M003
PAGE REFERENCE
SPARE PARTS
MILLING TOOLS
TOOLING SYSTEM
CARTRIDGE
LL TYPE CARTRIDGE .................................................................M002
BC TYPE CARTRIDGE ................................................................M004
SS TYPE CARTRIDGE ................................................................M006
BORING UNIT ..................................................................................M008
MI TYPE BORING BARS.................................................................M011
QUICK CHANGE TOOLING SYSTEM
CLASSIFICATION OF QUICK CHANGE SYSTEM .....................M012
FACE MILL ...................................................................................M013
FACE MILLING ADAPTER ..........................................................M014
SIDE CUTTER ..............................................................................M016
BORING TOOL.............................................................................M017
MODULAR TOOLING SYSTEM
......................................................................M018
HSK SYSTEM...............................................................................M022
*Arranged
M002 PSSNR/LppCApp
ABSppp-ES-M
M020
M020
M020
M021
M019
M020
M020
M020
M021
M019
M004
M004
M004
M008
M008
M008
M008
M002
M002
ABSppp-ES-M1
ABSppp-ES-M3
ABSppp-ES-M4
ABSppp-FS-W
ABSpp-ES-M
ABSpp-ES-M1
ABSpp-ES-M3
ABSpp-ES-M4
ABSpp-FS-W
CSKPRppCApp
CSSPRppCApp
CTGPRppCApp
FAp-FApppp
FAp-FAppppS
FVp-FVpppp
FVp-FVppppS
PCLNR/LppCApp
PSKNR/LppCApp
M002
M002
M002
M002
M021
M021
M021
M021
M011
M006
M006
M006
M006
M006
M006
PSYNRppCApp
PTFNR/LppCApp
PTGNR/LppCApp
PTTNRppCApp
SBAppp-ES-M
SBAppp-ES-M1
SBApp-ES-M
SBApp-ES-M1
SBRppp
SSKPRppCApp
SSSPRppCApp
SSYPRppCApp
STFPR/LppCApp
STGPRppCApp
STTPRppCApp
M001
TOOLING SYSTEM
CARTRIDGE
LL ISO type
Lever lock type
Lever lock type
Clamp Screw
Insert
Cartridge
Lever
Shim
a Negative insert.
a Large breaker selection.
a Suitable for steel and cast iron.
Type
Order Number
Shim Pin
Stock
Geometry
Insert Number
R L
a
90
S10
DMIN
HF
RE
LF
ASP
MHD
45
20
16CA
20CA
10CA
12CA
1604pp
PTGN
DMIN
S10
HF
RE
90
LF
ASP
MHD
MHH
B
WF
PTGNR/L12CA16
PTGNR/L16CA16
1103pp
1604pp
MHH
B
WF
PTFN
PTFNR/L10CA11
PTFNR/L12CA16
PTFNR/L16CA16
PTFNR/L20CA22
45
20
16CA
12CA
TNMA
TNMG
TNMM
TNGA
TNGG
2204pp
1604pp
1604pp
75
S10
HF
RE
LF
ASP
MHD
MHH
B
DMIN
WF
PSKN
PSKNR/L10CA09
PSKNR/L12CA12
PSKNR/L16CA12
45
20
16CA
10CA
12CA
SNMA
SNMG
SNMM
SNGA
SNGG
0903pp
1204pp
1204pp
PCLN
DMIN
95
S10
HF
RE
LF
ASP
MHD
MHH
B
WF
PCLNR/L12CA12
PCLNR/L16CA12
PCLNR/L20CA12
45
20
16CA
20CA
12CA
CNMA
CNMG
CNMM
CNGG
1204pp
1204pp
1204pp
TOOLING
DMIN
RE
ASP
S10
HF
RE
45
LF
MHD
MHH
B
WF
PSSN
PSSNR/L10CA09
PSSNR/L12CA12
PSSNR/L16CA12
45
20
16CA
10CA
12CA
SNMA
SNMG
SNMM
SNGA
SNGG
0903pp
1204pp
1204pp
PTTN
RE
HF
S10
60
LF
ASP
MHD
MHH
B
DMIN
WF
PTTNR12CA16
PTTNR16CA16
45
20
16CA
12CA
TNMA
TNMG
TNMM
TNGA
TNGG
1604pp
1604pp
85
S10
HF
DMIN
RE
LF
ASP
MHD
MHH
B
WF
PSYN
PSYNR10CA09
PSYNR12CA12
PSYNR16CA12
45
20
16CA
10CA
12CA
Clamp Torque (N m) : LLCS105=1.5, LLCS106=2.2, LLCS106S=2.2, LLCS108S=3.3
M002
SNMA
SNMG
SNMM
SNGA
SNGG
0903pp
1204pp
1204pp
Cutting Angle
90
F
G 90(Off Set)
K
75
L
95
S
45
T
60
Y
85
Insert
Clearance
N
10
Hand of Tool
R Right Hand
L Left Hand
CA
11
10
12
16
20
16
20
11
09 16
12.5 11
15.5 16
50
55
20
20
8 2
8 2
5
6
10
12
14 0.4 40
20 0.8 50
16
17
63
25
8 2.5
16
25 0.8 60
20
19
70
30 10 2.5
20
25 0.8 70
15.5 16
16
17
55
63
20
25
8 2
8 2.5
12
16
20 0.8 50
25 0.8 60
12.5 11
15.5 16
16
17
50
55
63
20
20
25
8 2
8 2
8 2.5
5
6
10
12
16
14 0.8 40
20 0.8 50
25 0.8 60
15.5 16
16
17
20
19
55
63
70
20 8 2
25 8 2.5
30 10 2.5
12
16
20
20 0.8 50
25 0.8 60
25 0.8 70
12.5 11
15.5 16
16
17
44
47
53
20
20
25
8 2
8 2
8 2.5
5
6
10
12
16
14 0.8 40
20 0.8 50
25 0.8 60
15.5 16
16
17
55
63
20
25
8 2
8 2.5
12
16
13 0.8 50
15 0.8 60
12.5 11
15.5 16
16
17
50
55
63
20
20
25
8 2
8 2
8 2.5
5
6
10
12
16
14 0.8 40
20 0.8 50
25 0.8 60
Inscribed
Circle
6.35
9.525
12 12 22 12.7
LLSSN
Insert Shape
12
z
x
LLSTN
Cutting Edge
Length (mm)
Cartridge
10
LLSCN
Dimensions(mm)
Tool Type
CA ISO A Type
Cutting Edge
Height (mm)
Shim
Shim Clamp Lever

Clamp
Pin
Lever Spring Screw
LLCL12S HLS1 LLCS105
Radial Axial Wrench

Set Bolt
Screw Screw
LLR1 KS1 zHKY25R
HSC06016
xHKY20F
HLS2
LLCS105
LLR1
KS1
LLCS106
LLR1
KS2
zHKY25R
xHKY20F
zHKY25R
xHKY20F
LLCS108S LLR2
KS2
zHKY30R HBH08030
HLS2
LLCS105
LLR1
KS1
HSC06020
LLCS106
LLR1
KS2
zHKY25R
xHKY20F
zHKY25R
xHKY20F
HSC06016
LLCL13S
LLCL13S
HSC06020
HBH08025
HBH08025
LLCL13S
HLS2
LLCS105
LLR1
KS1
LLCL14S
HLS3
LLCS106S LLR1
KS1
zHKY20R
zHKY25R
zHKY25R
xHKY20F
LLCS108S LLR2
KS2
zHKY30R HBH08025
HLS3
LLCS106S LLR1
KS1
zHKY25R
xHKY20F
LLCS108S LLR2
KS2
zHKY30R HBH08025
LLCS108S LLR2
KS2
zHKY30R HBH08030
LLCL14S
HSC06020
HSC06020
LLCL13S
HLS2
LLCS105
LLR1
KS1
LLCL14S
HLS3
LLCS106S LLR1
KS1
zHKY20R
zHKY25R
zHKY25R
xHKY20F
LLCS108S LLR2
KS2
zHKY30R HBH08025
HLS2
LLCS105
LLR1
KS1
HSC06020
LLCS106
LLR1
KS2
zHKY25R
xHKY20F
zHKY25R
xHKY20F
HSC06016
LLCL13S
HSC06016
HSC06020
TOOLING
Square
P Lever Lock
Insert Shape
C 80Rhombic
Square
S
T Triangle
Triangle
Clamp
Structure
80
Rhombic
y IDENTIFICATION
HBH08025
LLCL13S
HLS2
LLCS105
LLR1
KS1
LLCL14S
HLS3
LLCS106S LLR1
KS1
zHKY20R
zHKY25R
zHKY25R
xHKY20F
LLCS108S LLR2
KS2
zHKY30R HBH08025
CNpp type inserts

SNpp type inserts
TNpp type inserts
SPARE PARTS
HSC06020
A092 A097
A105 A109
A110 A115
P 001
M003
TOOLING SYSTEM
CARTRIDGE
BC ISO type
Clamp on type
Clamp on type
Clamp Screw
Clamp Bridge
Cartridge
a Suitable for steel, cast iron, aluminium alloys
Insert
and copper alloys.
Type
Order Number
Stock
Geometry
Insert Number
R L
H
DMIN
RE
HF
ASP
S10
90
LF
MHD
MHH
B
WF
CTGP
CTGPR10CA11
CTGPR12CA16
CTGPR16CA16
45
20
16CA
10CA
12CA
TPMN
TPMR
TPGN
1103pp
1603pp
1603pp

H
DMIN
CSKP
75
RE
HF
ASP
S10
LF
MHD
45
20
16CA
10CA

H
DMIN
CSSP
HF
45
RE
MHH
B
WF
CSSPR10CA09
S10
LF
ASP
20
MHD
TOOLING
* Clamp Torque (N m) : BC4=2.5, BC4L=2.5, BC5=5.0, BC6=5.0
M004
0903pp
1203pp
MHH
B
WF
CSKPR10CA09
CSKPR16CA12
SPMN
SPMR
SPGN
0903pp
y IDENTIFICATION
Clamp
Structure
C
Clamp On
Insert Shape
Square
S
T Triangle
Cutting Angle
F
90
G 90(Off Set)
K
75
S
45
T
60
Y
85
Insert
Clearance
P
11
10
Hand of Tool
R Right Hand
L Left Hand
CA
11
Cutting Edge
Height (mm)
10
12
16
10
Tool Type
CA ISO A Type
Cartridge
12
Cutting Edge
Length (mm)
Insert Shape
Square Triangle
16
11
09
16
12
22
Inscribed
Circle
6.35
9.525
12.7
PS
Dimensions(mm)
PT
Radial
Screw
TSS05006
Axial
Screw
KS1
Clamp Set
Wrench
Set Bolt
Shim
Pin
BC4
TKY10R
HSC06016
TSS06010
KS1
BC5
TKY20R
HSC06020
PT32
BCP201
TSS06010
KS2
BC6
TKY20R
HBH08025
Shim
50
55
63
20
20
25
8
8
8
2
2
2
5
6
10
12
16
14 0.4 38
20 0.8 50
25 0.8 55
12.5 11
16
17
50
63
20
25
8
8
2
2
10
16
14 0.8 38
25 0.8 55
TSS05006
KS1
BC4L
TKY10R
HSC06016
PS42
BCP251
TSS06010
KS2
BC6
TKY20R
HBH08025
12.5 11
44
20
10
14 0.8 38
TSS05006
KS1
BC4L
TKY10R
HSC06016
TOOLING
12.5 11
15.5 16
16
17
SPpp type inserts

TPpp type inserts
SPARE PARTS
A160
A162
P001
M005
TOOLING SYSTEM
CARTRIDGE
SS ISO type
Screw on type
Screw on type
Clamp Screw
Insert
Cartridge
a Suitable for steel, cast iron, aluminium alloys
and copper alloys.
Type
Order Number
Stock
Geometry
Insert Number
R L
a
DMIN
STFP
90
RE
HF
MHH
TPMX
TPGX
WF
STFPR/L10CA11
STFPR/L12CA16
S10
LF
TPMT
TPGX
20
ASP
1103pp
1603pp
MHD

a
DMIN
MHH
TPMX
TPGX
RE
HF
90
ASP
S10
LF
MHD
WF
STGP
STGPR10CA11
STGPR12CA16
STGPR16CA16
45
20
16CA
10CA
12CA
TPMT
TPGX
1103pp
1603pp
1603pp

H
DMIN
75
SSKP
RE
HF
S10
LF
20
ASP
MHD

DMIN
RE
SSSP
45
RE
HF
MHH
SPMT
SPGX
WF
SSSPR10CA09
SSSPR12CA12
0903pp
1203pp
MHH
B
WF
SSKPR10CA09
SSKPR12CA12
S10
LF
0903pp
1203pp
20
ASP
MHD
TOOLING
STTP
DMIN
RE
HF
S10
60
LF
ASP
MHD
MHH
45
20
16CA
10CA
12CA
TPMT
TPGX
1103pp
1603pp
1603pp

H
DMIN
HF
85
RE
S10
LF
ASP
20
MHD
Clamp Torque (N m) : CS300890T=1.0, TS4=3.5, TS5=7.5
0903pp
1203pp
MHH
B
WF
SSYPR10CA09
SSYPR12CA12
SSYP
M006
TPMX
TPGX
H
B
WF
STTPR10CA11
STTPR12CA16
STTPR16CA16
SPMT
SPGX
y IDENTIFICATION
Clamp
Structure
S
Screw On
Cutting Angle
F
90
G 90(Off Set)
K
75
S
45
T
60
Y
85
Insert Shape
Square
S
T Triangle
Insert
Clearance
P
11
Hand of Tool
R Right Hand
L Left Hand
CA
11
Cutting Edge
Height (mm)
10
12
16
Tool Type
CA ISO A Type
Cartridge
10
Cutting Edge
Length (mm)
Insert Shape
Inscribed
Square Triangle Circle
12
16
11
09
16
12
22
6.35
9.525
12.7
Dimensions(mm)
H
10
Clamp Screw
Radial Screw
Axial Screw
Wrench
Set Bolt
12.5 11
15.5 16
50
55
20
20
8
8
2
2
5
6
10
12
14 0.4 35
20 0.8 50
CS300890T
TSS05006
KS1
HSC06016
TS4
TSS06010
KS1
TKY08F
TKY10F
TKY15F
TKY20F
12.5 11
15.5 16
16
17
50
55
63
20
20
25
8
8
8
2
2
2
5
6
10
12
16
14 0.4 35
20 0.8 50
25 0.8 55
CS300890T
TSS05006
KS1
HSC06016
TS4
TSS06010
KS1
TS4
TSS06012
KS2
TKY08F
TKY10F
TKY15F
TKY20F
TKY15F
TKY20F
12.5 11
15.5 16
50
55
20
20
8
8
2
2
5
6
10
12
14 0.8 35
20 0.8 50
TS4
TSS05006
KS1
HSC06016
TS5
TSS06010
KS1
TKY10F
TKY15F
TKY20F
TKY25F
12.5 11
15.5 16
44
47
20
20
8
8
2
2
5
6
10
12
14 0.8 35
20 0.8 50
TS4
TSS05006
KS1
HSC06016
TS5
TSS06010
KS1
TKY10F
TKY15F
TKY20F
TKY25F
12.5 11
15.5 16
16
17
50
55
63
20
20
25
8
8
8
2
2
2
5
6
10
12
16
9 0.4 35
13 0.8 50
15 0.8 55
CS300890T
TSS05006
KS1
HSC06016
TS4
TSS06010
KS1
TS4
TSS06012
KS2
TKY08F
TKY10F
TKY15F
TKY20F
TKY15F
TKY20F
12.5 11
15.5 16
50
55
20
20
8
8
2
2
5
6
10
12
14 0.8 35
20 0.8 50
TS4
TSS05006
KS1
HSC06016
TS5
TSS06010
KS1
TKY10F
TKY15F
TKY20F
TKY25F
SPpp type inserts
A140
A146, A147
P 001
TPpp type inserts

SPARE PARTS
HSC06020
HSC06020
HBH08025
HSC06020
HSC06020
HSC06020
TOOLING
HBH08025
HSC06020
M007
TOOLING SYSTEM
BORING UNIT
FA,FV
y IDENTIFICATION
zSet Order Number
FA
a Precision finish
zSet Order
Number
FV Type
(Vertical Type)
mInsert Clearance Angle
1
,Lead Angle
* Sets are delivered with unit and cartridge assembled.

*
FA0-FASC01
FA0-FASC01S
FA1-FASP11
FA1-FASP11S
FA2-FASP21
FA2-FASP21S
FA2-FAPN21
FA3-FASP31
FA3-FASP31S
FA3-FAPN31
FA4-FAPN41
FV0-FVSC01
FV0-FVSC01S
FV1-FVSP11
FV1-FVSP11S
FV2-FVSP21
FV2-FVSP21S
FV2-FVPN21
FV3-FVSP31
FV3-FVSP31S
FV3-FVPN31
FV4-FVPN41
FA Type
(Angular Type)
nClamp Type
xUnit Order
FA0
FA0
FA1
FA1
FA2
FA2
FA2
FA3
FA3
FA3
FA4
FV0
FV0
FV1
FV1
FV2
FV2
FV2
FV3
FV3
FV3
FV4
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Number
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
cCartridge
Order Number
FASC01
FASC01S
FASP11
FASP11S
FASP21
FASP21S
FAPN21
FASP31
FASP31S
FAPN31
FAPN41
FVSC01
FVSC01S
FVSP11
FVSP11S
FVSP21
FVSP21S
FVPN21
FVSP31
FVSP31S
FVPN31
FVPN41
Stock
Cutting Mode
cCartridge Order Number
FA
bSize
Stock
vMounting Type
vMounting Type
Stock
boring unit.
a Facilitates precision
adjustment.
a High accuracy.
xUnit Order Number
bSize
Symbol
nClamp Type
Min. Cutting
Symbol
Diameter (mm)
0
0
19
19
S
S
25
25
36
Type
mInsert
Clearance Angle
Symbol Angle
C
C
7
7
Screw On
Screw On
Screw On
11
Screw On
11
Screw On
11
36
11
Screw On
Lever Lock
36
47
Screw On
11
47
11
3
4
47
73
P
P
Screw On
Lever Lock
Lever Lock
N
N
0
0
0
0
19
19
S
S
Screw On
C
C
7
7
25
11
25
Screw On
Screw On
11
36
11
36
11
36
Screw On
Screw On
Lever Lock
47
Screw On
11
47
Screw On
11
3
4
47
73
P
P
Lever Lock
N
N
0
0
a
a
Screw On
Lever Lock
* "S" at the end of the order number indicates left hand tool.
TOOLING
nCartridge Clamp Structure
S (Screw-on Type)
Applicable Size : 0,1,2,3
Applicable Size : 2,3

Insert
Clamp Screw
Insert
M008
P (Lever Lock Type)
Clamp Screw
Clamp Lever
,Lead Angle
P (Lever Lock Type with Shim)

Applicable Size : 4
Clamp Lever
Clamp Screw
FA
Lead Angle1 : 0
Insert
Shim
FV
0
Lead Angle1 : 0 0
Dial
Leaf Spring
Washer
Cartridge
Bush
Washer Screw
BORING UNIT SPARE PARTS

Unit
Order Number
FA0
FV0
FA1
FV1
FA2
FV2
FA3
FV3
FA4
FV4
Washer Screw
Unit Screw
Wrench
HSC02006
HSC02006
HSC02506
HSC02506
HSC03010
HSC03010
HSC04012
HSC04012
HSC05016
HSC05016
S1
S1
HY-A1
HY-V1
HY2
HY2
HY3
HY3
HY4
HY4
HKY15R
HKY15R
HKY20R
HKY20R
HKY20R,HKY25R
HS-N2,HKY25R
HKY20R,HKY30R
HKY20R,HKY30R
HKY30R,HKY40R
HKY30R,HKY40R
Bush
Washer
Leaf Spring
The parts above are not sold separately as accuracy

can only be guaranteed by having the complete set.
Please contact us for questions about parts replacement.
CARTRIDGE SPARE PARTS

z
*3
Applicable Insert
*1
Clamp Lever Lever Spring Clamp Screw
LLCL12S
LLCL12S
LLCL12S
LLCL12S
LLCL13
LLCL13
HLS1
HLS1
HLS1
HLS1
Shim
z TS2
z TS2
z CS250T
z CS250T
z CS300890T
z CS300890T
x LLCS103
x LLCS103
z CS300890T
z CS300890T
x LLCS103
x LLCS103
x LLCS106
LLSTN32
x LLCS106
LLSTN32
Shim Pin
Spanner
LLP13
LLP13
HR00
HR00
HR12
HR12
HR12
HR12
HR12
HR12
HR34
HR34
HR34
HR34
HR34
HR34
*2
Wrench
z TKY06F
z TKY06F
z TKY08F
z TKY08F
z TKY08F
z TKY08F
x HKY20F
x HKY20F
z TKY08F
z TKY08F
x HKY20F
x HKY20F
x HKY25F
x HKY25F
TCGT..L-F 060102
060104
TCGW
090204
TPGX
TPGX..L/R
TPMX..L/R 110304
110308
110304
TNGA
TNGG..L/R 110308
TPGX
TPGX..L/R
TPMX..L/R
110304
110308
110304
110308
TNGA
TNGG..L/R 160404
TOOLING
Cartridge
FASC01(S)
FVSC01(S)
FASP11(S)
FVSP11(S)
FASP21(S)
FVSP21(S)
FAPN21
FVPN21
FASP31(S)
FVSP31(S)
FAPN31
FVPN31
FAPN41
FVPN41
160408
160412
(Note) Use left hand inserts in the cartridge for right hand cutting and right hand inserts in the cartridge for left hand cutting.
1 "S" at the end of the cartridge number indicates left hand.
2 A spanner is only provided when ordered with a set.
3 Clamp Torque (N m) : TS2=0.6, CS250T=1.0, CS300890T=1.0, LLCS103=1.5, LLCS106=2.2
*
*
*
INSERTS
Finish Cutting
TCGT..L/R-F
(06) Â141
TPGX..L/R
(09,11) Â146
Medium Cutting
TPMX..L
(09,11) Â146
TNGG..L/R
(11,16) Â114
Flat Top
TPGX
TNGA
(09,11) Â147
(11,16) Â115
SPARE PARTS
P001
M009
TOOLING SYSTEM
BORING UNIT
MAIN DIMENSIONS
a FA TYPE (ANGULAR TYPE)
8
S14
I
RE
Z
Y
0.25DC2-Z2-Y
0.25DC2-Z2-(Y+0.6 x I)
S16
Cutting Edge
Movement
DC 5
ON
DMIN
BD
S20
S17
D1
Adjustment S15
L2
1
RE
S19
S1
3
S19=
S20=
DC (Cutting Diameter)
S1
L23
5308'
S1
2L
DR
ED
L23
Clockwise (right hand) tool shown.

Minimum cutting diameters (DMIN) correspond to RE0.2 (0 type) and RE0.4 (14 type).
Unit Center Line
Unit : mm
Set Order Number
FA0-FASC01(S)
FA1-FASP11(S)
FA2-FASP21(S)
FA2-FAPN21
FA3-FASP31(S)
FA3-FAPN31
FA4-FAPN41
RE DMIN
0.2
0.4
0.4
0.4
0.8
0.4
0.8
0.4
0.8
0.4
0.8
0.4
0.8
1.2
19
19
25
36
36
36
36
47
47
47
47
73
73
73
Adjustment
S14 S15
0.32
0.32
0.5
0.7
0.7
0.7
0.7
1.0
1.0
1.0
1.0
1.5
1.5
1.5
0.16
0.16
0.3
0.4
0.4
0.4
0.4
0.6
0.6
0.6
0.6
0.7
0.7
0.7
LDRED L21 S16 S17 L23
9.0
8.8
11.7
14.9
14.5
14.9
14.5
18.35
17.95
18.35
17.95
28.0
27.6
27.2
19.9
19.7
23.9
33.4
33.0
33.4
33.0
42.85
42.45
42.85
42.45
65.4
65.0
64.6
0.30
0.30
0.38
0.53
0.53
0.53
0.53
0.75
0.75
0.75
0.75
1.13
1.13
1.13
0.12
0.12
0.23
0.30
0.30
0.30
0.30
0.45
0.45
0.45
0.45
0.53
0.53
0.53
1.5
1.6
0.8
1.1
1.3
1.1
1.3
0.9
1.1
0.9
1.1
1.3
1.5
1.7
D15
DCON S12 S13 S18
11.11
11.11
15.08
19.05
19.05
19.05
19.05
22.225
22.225
22.225
22.225
31.75
31.75
31.75
15.06
15.06
19.05
24.58
24.58
24.58
24.58
31.75
31.75
31.75
31.75
46.02
46.02
46.02
2.7
2.7
3.2
4.0
4.0
4.0
4.0
4.8
4.8
4.8
4.8
6.4
6.4
6.4
8.2
8.2
9.0
14.5
14.5
14.5
14.5
19.7
19.7
19.7
19.7
31.0
31.0
31.0
1.11
1.11
0.46
0.7
0.7
0.7
0.7
0.54
0.54
0.54
0.54
0.86
0.86
0.86
BD
1.2
1.2
1.0
1.2
1.2
2.75
2.75
1.9
1.9
3.21
3.21
5.2
5.2
5.2
6.4
6.4
7.6
9.7
9.7
9.7
9.7
11.7
11.7
11.7
11.7
17.7
17.7
17.7
6.5
6.4
9.1
11.5
11.2
11.5
11.2
14.4
14.1
14.4
14.1
21.9
21.6
21.3
1.0
1.0
0.9
0.8
0.8
0.8
0.8
1.2
1.2
1.2
1.2
1.3
1.3
1.3
6.8
6.8
8.4
11.1
11.1
11.1
11.1
13.1
13.1
13.1
13.1
20.5
20.5
20.5
Max.
DC-2
DC-2
DC-2
DC-2
DC-2
DC-2
DC-2
DC-3
DC-3
DC-3
DC-3
DC-3
DC-3
DC-3
a FV TYPE (VERTICAL TYPE)

X
L23
S20=
Unit Center Line
Y
S20
BD
DMIN
Clockwise (right hand) tool shown.

Minimum cutting diameters (DMIN) correspond to RE0.2 (0 type) and RE0.4 (14 type).
Unit : mm
Set Order Number
FV0-FVSC01(S)
FV1-FVSP11(S)
FV2-FVSP21(S)
FV2-FVPN21
FV3-FVSP31(S)
FV3-FVPN31
FV4-FVPN41
RE DMIN
0.2
0.4
0.4
0.4
0.8
0.4
0.8
0.4
0.8
0.4
0.8
0.4
0.8
1.2
19
19
25
36
36
36
36
47
47
47
47
73
73
73
Adjustment
S14 S15
0.4
0.4
0.7
0.8
0.8
0.8
0.8
1.3
1.3
1.3
1.3
1.8
1.8
1.8
0.2
0.2
0.3
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
1.0
1.0
1.0
LDRED
L21
L23
D15
DCON
S12
S13
7.6
7.4
10.8
13.8
13.5
13.8
13.5
16.7
16.4
16.7
16.4
25.0
24.7
24.4
18.5
18.3
23.0
32.3
32.0
32.3
32.0
41.2
40.9
41.2
40.9
62.4
62.1
61.8
2.6
2.6
3.6
4.0
4.0
4.0
4.0
4.8
4.8
4.8
4.8
7.1
7.1
7.1
11.11
11.11
15.08
19.05
19.05
19.05
19.05
22.225
22.225
22.225
22.225
31.75
31.75
31.75
15.06
15.06
20.62
24.58
24.58
24.58
24.58
31.75
31.75
31.75
31.75
46.02
46.02
46.02
2.7
2.7
3.2
4.0
4.0
4.0
4.0
4.8
4.8
4.8
4.8
6.4
6.4
6.4
8.2
8.2
9.0
14.5
14.5
14.5
14.5
19.7
19.7
19.7
19.7
31.0
31.0
31.0
1.2
1.2
1.0
1.2
1.2
2.1
2.1
1.9
1.9
3.21
3.21
5.2
5.2
5.2
2.6
2.6
3.6
4.0
4.0
4.0
4.0
4.8
4.8
4.8
4.8
7.1
7.1
7.1
7.6
7.4
10.8
13.8
13.5
13.8
13.5
16.7
16.4
16.7
16.4
25.0
24.7
24.4
* "S" at the end of the order number indicates left hand tool.
M010
Adjustment S15
LDRED
S12
L21
S13
TOOLING
D15
DCON
0.25DC2-Z2-Y
S14
RE
DC (Cutting Diameter)
L23
BD
Max.
DC-2
DC-2
DC-2
DC-2
DC-2
DC-2
DC-2
DC-3
DC-3
DC-3
DC-3
DC-3
DC-3
DC-3
MI
TYPE
BORING BARS
y IDENTIFICATION
S
z
zClamp Type
Name
cShank Shape
R
08
b
bShank Size (mm)
vLead Angle
xBoring Bar
S Screw On Type
08
30
10
10
45
12
12
90
16
16
Round Shank
STANDARD HOLDER
Order Number
Geometry
Stock
For
Clockwise
SBR1
LF
WF
LDRED
RE
ASP
SBR110
SBR112
SBR308
SBR310
SBR312
SBR408
SBR410
SBR412
SBR416
SBR608
SBR610
SBR612
TPGX
TPGX...L
TPMX...L
B LF LDRED ASP HF WF RE
7 3.5 0.4
0902pp
9 10 50 11
8 4.5 0.4
1103pp
10 12 60 12
10 5.0 0.4
0802pp
8 35
HF
LF
WF
LDRED
30
HF
0802pp
8 35 10
7 0.7 0.4
0902pp
9 10 50 12
8 1.0 0.4
1103pp
10 12 60 13
10 1.0 0.4
RE
6
LDRED
WF
LF
HF
TPGX
TPGX...L
TPMX...L
WF
LF
SBR4
45
ASP
LF
SBR3
ASP
SBR108
Dimensions (mm)
* Insert Number
WF
LF
TPGX
TPGX...L
TPMX...L
0802pp
8 35 10
7 0.5 0.4
0902pp
9 10 50 12
8 1.0 0.4
1103pp
10 12 60 13
10 1.0 0.4
1103pp
14 16 80 13
14 0
0.8
RE
SBR6
LDRED
LF
RE
8.5
0.4
8 10 50 10
0.4
10 12 60 11
10
0.4
0802pp
0902pp
1103pp
8 35
ASP
LF
TOOLING
HF
TPGX
TPGX...L
TPMX...L
(Note) When using an insert with a breaker, please use a left hand insert.
SPARE PARTS
x
Insert
Order Number
zClamp Screw
Wrench
08
CS200T
TKY06F
10
CS250T
TKY08F
12
CS300890T
KS1S
TKY08F
16
CS300890T
KS2S
TKY08F
SBR1
xPre-Set Screw
SBR6
* Clamp Torque (N m) : CS200T=0.6, CS250T=1.0, CS300890T=1.0

a
TPpp type inserts

SPARE PARTS
A146, A147
P 001
M011
TOOLING SYSTEM
CLASSIFICATION OF QUICK CHANGE

MODULAR TOOLING SYSTEM
Mitsubishi's quick change system is a must for improving efficiency in mass production lines.
a Shorten tool change times and increase machine efficiency.
a Reduce tool weight. Thus, tool change is safer and easier.
a Improve cutting edge accuracy.
QF2000 (Small Diameter)
QF1000 (Two Piece)
QC TYPE ADAPTER
FOR PIN MILLING CUTTER
QF2000 (Large Diameter)
QS2000 (Arbor for Side Cutter)
MITSUBISHI's
QUICK CHANGE
SYSTEM
Connecting System
QB2000 QB3000
Boring Tool
Face Mill and Pin Milling Cutter
ABS License KOMET
HSK
QB4000
TOOLING
Special Tooling
M012
SPQH (Spring)
SPQS (Spring+Oil pressure)
Setting Fixture
Setting Gauge
FACE MILL
QF2000 (SINGLE BOLT MOUNTING TYPE)
a One Piece Type ( < & 160)
Machine Spindle
Adapter
Yellow Mark
Yellow Mark
y FEATURES
1. Simply turning a clamp bolt fixed to the adapter a few times enables
cutter exchange.
2. The cutter needs to be turned 90 before removal. This prevents the
cutter from falling free.
3. Applicable to both face milling and boring tools.
4. Cutter exchange time is less than 1 min.
Clamp Bolt
Cutter Body
a Two Piece Type ( > & 200)

Cutter Body
Adapter
Clamp Bolt
Setting Plate
Mounting
Teeth
y FEATURES
1. Internal diameter of the cutter body has 4 6 mounting teeth.
The adapter has the same mounting teeth and a single clamp bolt
for installation.
2. The cutter needs to be turned 15 before removal. This prevents the
cutter from falling free.
QF1000 (GOURD SHAPED HOLE TYPE)

a Two Piece Type (T Type > & 250)
TOOLING
a One Piece Type (O Type & 200)
y FEATURES
1. Gourd shaped hole type is employed. Turning 4 6 bolts enables cutter exchange.
2. The cutter needs to be turned 15 before removal. This prevents the cutter from falling free.
3. Cutters with > 250 are made up of 2 parts. Thus, weight at the time of installation is reduced and safety is improved.
4. Standard adapters facilitate installation of cutters with the same diameter and different insert shapes.
5. Cutter exchange time is less than 3 5 min.
M013
TOOLING SYSTEM
FACE MILLING ADAPTER

a Standard
L8 (Key Groove Depth)

13 FLGT 15
Q TYPE (SINGLE BOLT TYPE) & 80 &160

DF
DCON_MS
a Installed Condition
Machine Spindle
Adapter
Cutter Body
"M" Bolt Hole
Clamp Bolt
DCON_WS
KW
W
45
DB
Unlock
L2
Lock
Order Number
Cutter Diameter
(DC)
QFA08025BCR/L
QFA10025BDR/L
QFA12530BER/L
QFA16030BFR/L
80
100
125
160
Cutter Dimensions (mm)

DF
DCON_WS FLGT DCON_MS
70
80
100
125
25.4
31.75
38.1
50.8
25
25
30
30
25.4
31.75
38.1
50.8
DBC
45
55
70
85
Machine Dimensions (mm)

M
KWW
L8
M12
M16
M20
M20
9.5
12.7
15.9
19
7
8
10
11
Tool Weight
L24
(kg)
18.4
23.2
28
36
0.8
1.2
2.1
3.2
L8
M014
KWW
d2
BD
DCON
R7/5
TOOLING
DF
7/24 Taper No.
13
Order Number
Cutter Diameter
(DC)
QFA08025N4R/L
QFA10025N4R/L
QFA12530N4R/L
QFA16030N4R/L
QFA08025N5R/L
QFA10025N5R/L
QFA12530N5R/L
QFA16030N5R/L
80
100
125
160
80
100
125
160
LB
LS

BD
DCON
LB
70
80
100
125
70
80
100
125
25.4
31.75
38.1
50.8
25.4
31.75
38.1
50.8
25
25
30
30
25
25
30
30
L24
DF
No.
70
80
100
125
100
100
100
125
40
40
40
40
50
50
50
50

d2
LS
KWW
44.45
44.45
44.45
44.45
69.85
69.85
69.85
69.85
93.4
93.4
93.4
93.4
126.8
126.8
126.8
126.8
16.1
16.1
16.1
16.1
25.7
25.7
25.7
25.7
Tool Weight
L8
L24
(kg)
16
16
16
16
19
19
19
19
22.5
22.5
22.5
22.5
35.3
35.3
35.3
35.3
1.4
1.7
2.7
3.8
3.2
3.4
4.0
5.1
Q TYPE (SINGLE BOLT TYPE) &200&500

Bolt Hole for M16
Bolt Hole for M20
DF
DCON_MS
25.4
Machine Spindle
11
a Standard
Adapter
350.01
800.05
10
DCON_WS
Cutter Body
Clamp Bolt
Unlock
45
45
50.8
DBC
Lock
101.6
Order Number
Cutter Diameter
(DC)
QFB20035KR/L
QFB25035KR/L
QFB31535PR/L
QFB35535PR/L
QFB40035PR/L
QFB50035PR/L
200
250
315
355
400
500

DCON_WS
DF
125
175
240
280
325
425

DCON_MS
DBC
177.8
177.8
177.8
177.8
47.625
47.625
47.625
47.625
47.625
47.625
190
240
305
345
390
490
Tool Weight
m
(kg)
88.9
88.9
88.9
88.9
9
16
28
37
49
83
T TYPE (SIX BOLT TYPE) & 250 & 400

Bolt for M16 (4 Piece)
Bolt for M20 (4 Piece)
Machine Spindle
Adapter
800.05
Bolt for M20 x 50 (N Piece)

(JIS B 1176)
* Adapter is for both right and left hand tools.
Cutter Body
TOOLING
101.6
DBC_2
DCON_WS
DBC
DF
LB
15
DCON_MS
25.4
350.01
a Standard
Unlock
Lock
Order Number
Cutter Diameter
(DC)
DCON_WS
QFA25035K
QFA31535P
QFA35535P
QFA40035P
250
315
355
400
110
175
215
260

DBC
DF
LB
155
220
260
305
4
6
6
6
230
295
335
380
45
50
50
50
Machine Dimensions (mm) Tool Weight

DCON_MS
DBC_2
(kg)
47.625
47.625
47.625
47.625
177.8
177.8
177.8
9
16
22
29
M015
TOOLING SYSTEM
SIDE CUTTER
QC TYPE ADAPTER FOR PIN MILLING CUTTER
y FEATURES
a Cutter Body
1. Makes installation of Pin millng cutter easy, quick, and

accurate.
2. Clamping the entire periphery of the cutter body
improves rigidity and lateral run-out of the cutting edges.
3. Facilitates stable heavy cutting such as counter weight
cutting and prevents sudden insert fracture.
a Adapter Body
QS2000 (INSTALLATION METHOD FOR SIDE CUTTER)

y FEATURES
TOOLING
a Appearance
1. Turning the bolt a few times turns nut 45 and enables

installation and detachment of the cutter.
2. Installation and detachment of the cutter is possible
without taking the bolt and nut off the adapter.
3. The cutter is a solid type. Thus, the rigidity is high.
Clamp Bolt
Nut
Adapter
Side Cutter
M016
BORING TOOL
QB4000 TYPE (SIDE CLAMP TYPE)
Snap Ring
Clamp Bolt
Steel Ball
O Ring
Spring
y FEATURES
1. Tightening the clamp bolt (or clamp nut) draws the clamp washer in
and securely holds the boring head.
2. The clamp washer has mounting teeth at the end. Turning the clamp
washer 45 enables installation and detachment of the boring head.
3. Both 1/5 taper and cutter locating faces support the boring head. Thus,
clamp rigidity and installation repeatability accuracy are high (23!m).
4. A side clamp structure is employed. Thus, a spindle turning stopper is
unnecessary. This structure prevents the boring head from falling free.
5. Insert location close to the adapter body allows for convenient head
exchange.
6. Suitable for a wide range of boring, from small to large diameters.
7. Head exchange time is less than 1 min.
Clamp Washer
O Ring
Nut
Adapter Body
a Installation Standard
45
8(H8) (Long Hole)
DF
DBC
DCON_MS
d3
DCON_WS
2230'
d4
2-M12
TOOLING
Drive Pin
0.5
0.5
Taper 1/5
30
LB
15
Order Number
DCON_WS
DCON_MS
DF
d3
DBC
LB
d4
QB4350070
35
30
70
28
52
M8
22
QB4350088
35
30
88
28
70
M8
22
QB4400098
40
30
98
34
80
M8
24
QB4400118
40
30
118
34
90
M10
24
10
QB4500138
50
40
138
42
110
M12
30
12
M017
TOOLING SYSTEM
ABS SYSTEM CHARACTERISTIC

a High rigidity and high coupling strength.
a From small ( &20) diameter to large diameter
The taper wedge effects produced by the clamping

screw, the taper screw, and the slide pin enable strong
and firm coupling between the head and the adapter.
a As the cutting torque acts as torsion force on the axis,
50% 80% improvement is achieved for the clamping

strength in the coupled portion axis direction.
a High accuracy is guaranteed.
( &200), a wide range of tooling is possible.

a Internal passage of the coolant (air) is possible
without modifications to standard machinary.

a Tool head extensions are easy through the use of
extension pieces.
a Through the use of reducers, tool head diameters
are easily set.
An attachment repeat accuracy of 2 3!m is

constantly maintained in the coupled portion.
ABS SYSTEM MECHANISM
General type Spindle

(NT, BT setting)
TOOLING
ABS
Adapter, Shank
ABS
Holder
ABS
Flanges type Adapter
ABS
Extension
ABS
Taper Shank
ABS
Milling Holder
ABS
Heads
(Note) The above chart also indicates the
M018
standard.
ABS SYSTEM COMPONENT

F2
Taper Screw
Head Slide Pin

2xFA
FA
FA
Position Pin
Adapter
Clamp Screw
F1
When the force F1 presses on the clamping screw, the slide pin
moves in the radial direction and impinges on the taper screw,
generation the reaction force F2. Since the centers of the clamping
screw, the taper screw, and the slide pin are eccentric, a taper
connection is made at sites separated by a 180 phase, with the
clamping screw and the slide pin on the taper right impingement
portion, and the slide pin and taper pin on the taper left impingement
portion. The result is that, a vector analysis of those forces shows, as
depicted in the diagram above, that the slides move in an identical
direction, and the coupling force FA is doubled and transmitted
accordingly. Further, cutting resistance generated during cutting
becomes torsion stress and is transmitted accordingly. The forces F1
and F2 generated with the clamping screw and taper screw are
expanded, and the coupling (jointing) force FA becomes as even
greater force, and is generated accordingly.
ABS SYSTEM SETTING STANDARDS
This system is licensed from

(JP Patent NO.1328669)
of Germany.
Adapter Dimensions
Dimensions(mm)
CBDP
Order Number
S1
L24min.
ABS25W
ABS32W
ABS40W
ABS50W
ABS63W
ABS80W
ABS100W
ABS125W
DCON
CBDP
L24
S1
25
32
13
16
22
25
13
16
8.3
10.3
40
20
30
18.5
11.3
50
28
34
22
13.3
63
34
41
28
17.4
80
46
48
34
20.4
100
125
56
70
58
76
40.5
51
24.4
30.5
Pack Order
Number
Stock
a Parts for Adapter

Clamp Screw
Taper Screw
ABS25-F1
ABS32-F1
ABS25-F2
ABS32-F2
ABS40-F1
ABS40-F2
ABS50-F1
ABS50-F2
ABS63-F1
ABS63-F2
ABS80-F1
ABS80-F2
ABS100-F1
ABS125-F1
ABS100-F2
ABS125-F2
TOOLING
BD
DCON
BD
Clamp Screw
Taper Screw
ABS25-FS-W
ABS32-FS-W
ABS40-FS-W
ABS50-FS-W
ABS63-FS-W
ABS80-FS-W
ABS100-FS-W
ABS125-FS-W
* An order of the above type of screw and pin needs to be included in the set. Please use a "Pack Order Number" for your order.
a
M019
TOOLING SYSTEM
a Head Dimensions
Dimensions(mm)
Order Number
BD
BD
DCON
ABS25M
ABS32M
ABS40M
ABS50M
ABS63M
ABS80M
ABS100M
ABS125M
S1
LS
DCON
LS
S1
25
32
13
16
20
23
8
10
40
20
26
11
50
28
31
13
63
34
38
17
80
46
43
20
100
125
56
70
55
70
24
30
Pack Order
Number
Screw
Position Pin
Slide Pin
ABS25-ES-M
ABS32-ES-M
ABS40-ES-M
ABS50-ES-M
ABS63-ES-M
ABS80-ES-M
ABS100-ES-M
ABS125-ES-M
Stock
a Parts for Head

Slide Pin
Position Pin
Screw
ABS25-E3
ABS32-E3
ABS25-E4
ABS32-E4
ABS25-E5
ABS32-E5
ABS40-E3
ABS40-E4
ABS40-E5
ABS50-E3
ABS50-E4
ABS50-E5
ABS63-E3
ABS63-E4
ABS63-E5
ABS80-E3
ABS80-E4
ABS80-E5
ABS100-E3 ABS100-E4 ABS100-E5

ABS125-E3 ABS125-E4 ABS125-E5
Pack Order
Number
Screw
Position Pin
ABS25-ES-M1
ABS32-ES-M1
ABS40-ES-M1
ABS50-ES-M1
ABS63-ES-M1
ABS80-ES-M1
ABS100-ES-M1
Slide Pin
Position Pin
Screw
ABS25-E3
ABS32-E3
ABS25-E4.1
ABS32-E4.1
ABS25-E5
ABS32-E5
ABS40-E3
ABS40-E4.1
ABS40-E5
ABS50-E3
ABS50-E4.1
ABS50-E5
ABS63-E3
ABS63-E4.1
ABS63-E5
ABS80-E3 ABS80-E4.1 ABS80-E5

ABS100-E3 ABS100-E4.1 ABS100-E5
a Parts for Head [For Coolant Hole Type]

Pack Order
Number
Tube
Position Pin
Slide Pin
ABS25-ES-M3
ABS32-ES-M3
ABS40-ES-M3
ABS50-ES-M3
ABS63-ES-M3
ABS80-ES-M3
ABS100-ES-M3
ABS125-ES-M3
Stock
TOOLING
Slide Pin
Stock
a Parts for Head [For Fine Boring]
Slide Pin
Position Pin
Tube
ABS25-E3.2
ABS32-E3.2
ABS25-E4
ABS32-E4
ABS25-E6
ABS32-E6
ABS40-E3.2
ABS40-E4
ABS40-E6
ABS50-E3.2
ABS50-E4
ABS50-E6
ABS63-E3.2
ABS63-E4
ABS63-E6
ABS80-E3.2
ABS80-E4
ABS80-E6
ABS100-E3.2 ABS100-E4 ABS100-E6

ABS125-E3.2 ABS125-E4 ABS125-E6
* An order of the above type of screw, pin and tube needs to be included in the set. Please use a "Pack Order Number" for your order.
a
M020
Pack Order
Number
Tube
Stock
a Parts for Head [For Fine Boring with Coolant Hole]
ABS25-ES-M4
ABS32-ES-M4
ABS40-ES-M4
ABS50-ES-M4
ABS63-ES-M4
ABS80-ES-M4
ABS100-ES-M4
Position Pin
Slide Pin
Slide Pin
Position Pin
Tube
ABS25-E3.2 ABS25-E4.1
ABS32-E3.2 ABS32-E4.1
ABS25-E6
ABS32-E6
ABS40-E3.2 ABS40-E4.1
ABS40-E6
ABS50-E3.2 ABS50-E4.1
ABS50-E6
ABS63-E3.2 ABS63-E4.1
ABS63-E6
ABS80-E3.2 ABS80-E4.1 ABS80-E6

ABS100-E3.2 ABS100-E4.1 ABS100-E6
Screw
Pack Order
Number
Key
Position Key
Slide Pin
SBA25-ES-M
SBA32-ES-M
SBA40-ES-M
SBA50-ES-M
SBA63-ES-M
SBA80-ES-M
SBA100-ES-M
SBA125-ES-M
Stock
a Parts for Head [For Key Type]

Slide Pin
Key
Position Key
Screw
ABS25-E3
ABS32-E3
SBA25-E4
SBA32-E4
SBA25-E4.1
SBA32-E4.1
ABS25-E5
ABS32-E5
ABS40-E3
SBA40-E4
SBA40-E4.1
ABS40-E5
ABS50-E3
SBA50-E4
SBA50-E4.1
ABS50-E5
ABS63-E3
SBA63-E4
SBA63-E4.1
ABS63-E5
ABS80-E3
SBA80-E4
SBA80-E4.1
ABS80-E5
ABS100-E3 SBA100-E4 SBA100-E4.1 ABS100-E5

ABS125-E3 SBA125-E4 SBA125-E4.1 ABS125-E5
Key
Position Key
Slide Pin
SBA25-ES-M1
SBA32-ES-M1
SBA40-ES-M1
SBA50-ES-M1
SBA63-ES-M1
SBA80-ES-M1
SBA100-ES-M1
SBA125-ES-M1
Slide Pin
Key
Position Key
Tube
ABS25-E3.2
ABS32-E3.2
SBA25-E4
SBA32-E4
SBA25-E4.1
SBA32-E4.1
ABS25-E6
ABS32-E6
ABS40-E3.2
SBA40-E4
SBA40-E4.1
ABS40-E6
ABS50-E3.2
SBA50-E4
SBA50-E4.1
ABS50-E6
ABS63-E3.2
SBA63-E4
SBA63-E4.1
ABS63-E6
ABS80-E3.2
SBA80-E4
SBA80-E4.1
ABS80-E6
ABS100-E3.2 SBA100-E4 SBA100-E4.1 ABS100-E6

ABS125-E3.2 SBA125-E4 SBA125-E4.1 ABS125-E6
* An order of the above type of screw, pin and tube needs to be included in the set. Please use a "Pack Order Number" for your order.
TOOLING
Tube
Pack Order
Number
Stock
a Parts for Head [For Key Type with Coolant Hole]
M021
TOOLING SYSTEM
HSK SYSTEM
FEATURES OF THE HSK SYSTEM
aSuitable for high speed machining.
When the taper hole is slightly seperated during high

speed machining due to centrifugal force, the taper axis
1/10 Taper
Held Tightly
Contact Faces
Held Tightly
Coolant Hole
is continuously in contact with the taper hole because of

elastic deformation. Thus, 2 face holding is maintained.
aGuaranteed high accuracy.
Installation repeatability of 2!m is guaranteed.

aHigh rigidity.
High rigidity in the radial and thrust direction due to the

2 face holding system.
Clamp Bridge
aEasy installation.
Detachable support structure ensures separation of the
Tapered Tool (Tool)
Clamp Screw
Taper Hole (Spindle)
tool even when the tool has undergone thermal

expansion.
aCoolant system selection.
Center coolant and anglar flow coolant type.
* HSK stands for Hole (Hollow) Schaft (axis) Kegel (taper) in German.
HSK CLAMPING METHOD

30Conical Face
a The 30conical face of the taper axis is pulled in the
direction of the tapered hole to clamp.

Draw In
Tapered Tool (Tool)
TOOLING
a Temporary Clamp

Clearance
Position
The spindle
taper face and
the tool taper
face contact.
a Temporary clamp position has a clearance between
the spindle and the tool contact faces.

a Taper clamping force increases as the diameter
increases.
Tapered Tool (Tool)
a Permanent Clamp
Held Tightly
Position
a Hollow thin taper axis holds the taper faces and the
contact faces tightly due to pressurized elastic

deformation.
Tapered Tool (Tool)
M022
Type
There are various HSK types.

Mitsubishi Materials produces A, B, C, and
D types of taper axis (tool size) and C and
D types (manual operation) of taper hole
(spindle side).
A Type Automatic tool change (ATC), center coolant (mainly milling tools)
B Type Automatic tool change (ATC), angular flow coolant (mainly turning tools)
C Type Manual tool change, center coolant (mainly milling tools)
D Type Manual tool change, angular flow coolant (mainly turing tools)
r : Non
stock, produced to order only.
Order Number
Diameter DCON
Coolant Pipe
Hole for ID Insert
Coolant Hole
Hole for Manual Wrench
LS
Dimensions (mm)
DCON
LS
HSK-A32M
32
16
HSK-A40M
40
20
HSK-A50M
50
25
HSK-A63M
63
32
HSK-A80M
80
40
HSK-A100M
100
50
Drive Key
LS
Diameter DCON
Milling Tool
A Type (Center Coolant Type)

C Type (Center Coolant Type)
Automatic Tool Change
Grip Groove for ATC
Manual Tool Change
Tapered Tool Tapered Hole

(Tool)
(Spindle)
Application
Order Number
Dimensions (mm)
DCON
LS
HSK-C32M
32
16
HSK-C40M
40
20
HSK-C50M
50
25
HSK-C63M
63
32
HSK-C80M
80
40
HSK-C100M
100
50
Drive Key
TOOLING
HSK SYSTEM FORM
M023

OF DRILLING TOOLS
zArranged in order of solid carbide drills, brazed type drills, indexable type drills and high-speed
steel drills.
PHOTO OF PRODUCT
PRODUCT TITLE
DIAMETER TOLERANCE GEOMETRY
PRODUCT CODE
PRODUCT SECTION
SUITABLE WORK MATERIALS
PRODUCT TYPE
DRILLING(SOLID CARBIDE)
MVS
WSTAR DRILLS
for small diameter
CARBIDE
Steel
TAW
a Linear tooth profile improves both chip discharge and cutting edge strength.
a Double margin specifications offer optimum balance and high precision with small drills
Product Code
1 < DC < 2.9
Other than MVS-X02
+ 0.014
0
0
0.014
Product Code
DCON
MVS-X02-
Stainless Steel Cast Iron Non-ferrous Metal Heat Resistant Alloy
h6
aWavy cutting edge design for good chip control.

aSerration geometry for accurate insert location.
Steel
Stainless Steel
Cast Iron
CARBIDE
(General Use)
0
0.006
MVS
Type1
Dimensions (mm)
Insert
71.4 102.4 158.4 155
PL DCON
Clamp
Screw
Wrench
Plate
DC
Anti-seize (mm)
Lubricant
18.5
3
Type3
TAWSN1900S25
3.4
25 WS304517T TKY10T WPT4405 MK1KS
18.6
18.7
18.8
18.9
18.5
Type4
19.4
TAWMN1900S25
110.4 137.4 193.4 190
3.4
19.0
19.1
DRILLING
1.2
1.3
12
20
25
30
*S
7
12
20
25
30
*S
7
12
20
25
30
0.2
55
0.2
24.2 28.2 60.2
60
0.2
28.2 32.2 66.2

33.2 37.2 72.2
66
72
0.2
0.2
3
3
3
3
5.6 9.1 55.2

11.2 15.2 55.2
55
55
0.2
0.2
3
3
1
3
17.2 21.2 55.2
55
0.2
*S
7
12
20
25
30
*S
7
12
1.4
1.5
25.2 29.2 60.2
60
0.2
20
31.2 34.2 66.2

36.2 40.2 72.2
66
72
0.2
0.2
3
3
3
3
25
30
6.2 9.6 55.2

12.2 15.2 55.2
55
55
0.2
0.2
3
3
1
3
*S
7
18.2 21.2 55.2
55
0.2
12
28.2 31.2 60.2
60
0.2
20
34.2 37.2 66.2

40.2 43.2 72.2
66
72
0.2
0.2
3
3
3
3
25
30
6.6 9.8 55.2

13.2 16.2 55.2
55
55
0.2
0.2
3
3
1
3
*S
7
20.2 23.2 55.2
55
0.2
12
30.2 33.2 68.2
68
0.2
20
36.2 40.2 74.2

43.2 46.2 82.2
74
82
0.2
0.2
3
3
3
3
25
30
1.6
1.7
MVS0140X02S030
MVS0140X07S030
MVS0140X12S030
MVS0140X20S030
MVS0140X25S030
MVS0140X30S030
MVS0150X02S030
MVS0150X07S030
MVS0150X12S030
MVS0150X20S030
MVS0150X25S030
MVS0150X30S030
MVS0160X02S030
MVS0160X07S030
MVS0160X12S030
MVS0160X20S030
MVS0160X25S030
MVS0160X30S030
MVS0170X02S030
MVS0170X07S030
MVS0170X12S030
MVS0170X20S030
MVS0170X25S030
MVS0170X30S030
7.2 10.2 55.2

14.3 17.3 55.3
55
55
0.2
0.3
3
3
1
3
21.3 24.3 55.3
55
0.3
32.3 35.3 68.3
68
0.3
39.3 42.3 74.3

46.3 49.3 82.3
74
82
0.3
0.3
3
3
3
3
7.6 10.4 55.2

15.3 18.3 55.3
55
55
0.2
0.3
3
3
1
3
23.3 26.3 55.3
55
0.3
LH
55
15.2 19.2 55.2
(mm) (l/d)
LCF
10.2 14.2 55.2
Hole Depth
DP1020
Type
35.3 37.3 68.3
68
0.3
42.3 45.3 74.3

50.3 52.3 82.3
74
82
0.3
0.3
3
3
3
3
8.3 10.9 68.3

16.3 19.3 68.3
68
68
0.3
0.3
3
3
1
3
24.3 27.3 68.3
68
0.3
37.3 39.3 78.3
78
0.3
45.3 47.3 86.3

53.3 55.3 95.3
86
95
0.3
0.3
3
3
3
3
8.7 11.1 68.3

17.3 19.3 68.3
68
68
0.3
0.3
3
3
1
3
26.3 28.3 68.3
68
0.3
39.3 42.3 78.3
78
0.3
48.3 50.3 86.3

56.3 59.3 95.3
86
95
0.3
0.3
3
3
3
3
165.5 188.5 244.5 241
3.5
25 WS304517T TKY10T WPT4405 MK1KS 19.3
19.5
3
TAWSN2000S25
75.5 102.5 158.5 155
3.5
19.6
19.7
19.8
19.9
19.5
20.4
TAWMN2000S25
116.6 142.6 198.6 195
3.6
20.0
20.1
20.2
TAWLN2000S25
173.7 196.7 252.7 249
3.7
25 WS304518T TKY10T WPT4405 MK1KS 20.3

20.4
TAWNH1850T
TAWKH1850TG
TAWNH1860T
TAWKH1860TG
TAWNH1870T
TAWKH1870TG
TAWNH1880T
TAWKH1880TG
TAWNH1890T
TAWKH1890TG
TAWNH1900T
TAWKH1900TG
TAWNH1910T
TAWKH1910TG
TAWNH1920T
TAWKH1920TG
TAWNH1930T
TAWKH1930TG
TAWNH1940T
TAWKH1940TG
TAWNH1950T
TAWKH1950TG
TAWNH1960T
TAWKH1960TG
TAWNH1970T
TAWKH1970TG
TAWNH1980T
TAWKH1980TG
TAWNH1990T
TAWKH1990TG
TAWNH2000T
TAWKH2000TG
TAWNH2010T
TAWKH2010TG
TAWNH2020T
TAWKH2020TG
TAWNH2030T
TAWKH2030TG
TAWNH2040T
TAWKH2040TG
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
r
r
r
r
r
r
r
(Note 1) The dimensions in brackets represent the sizes when TAWN-U type inserts are used.
(Note 2) Please contact us for any geometry that is not in this catalogue (e.g. different diameter and length).
*S=Drill for guide hole Dimensions = 0+0.014, Hole depth=2DC

(Note) The coolant hole of 5.9mm or less will be round shape.
N012
TAWLN1900S25
19.4
0.2
DCON
*S
7
55
Order Number
PL
8.9 55.2
Dimensions (mm)
LF
25
30
5.2
DC
Stock
OAL
20
DCON
PL
1.1
Type
LF
1.0
7
12
MVS0100X02S030
MVS0100X07S030
MVS0100X12S030
MVS0100X20S030
MVS0100X25S030
MVS0100X30S030
MVS0110X02S030
MVS0110X07S030
MVS0110X12S030
MVS0110X20S030
MVS0110X25S030
MVS0110X30S030
MVS0120X02S030
MVS0120X07S030
MVS0120X12S030
MVS0120X20S030
MVS0120X25S030
MVS0120X30S030
MVS0130X02S030
MVS0130X07S030
MVS0130X12S030
MVS0130X20S030
MVS0130X25S030
MVS0130X30S030
OAL
Order Number
LH
*S
DC
19.2
Internal Coolant
Dimensions (mm)
LCF
(mm) (l/d)
DP1020
Hole Depth
Internal Coolant
Stock
Order
Number
DRILLING
LH OAL LF
VP10H
Stock
(l/d)
LU
DP5010
(mm)
Holder
Order Number
VP15TF
DC
Stock
Type2
Hole Depth
y HOLDERS
a
r

INSERT DESCRIPTION
CUTTING CONDITIONS
N234
N238
USAGE NOTE
TECHNICAL DATA
N238
Q001
N229
PRODUCT STANDARDS
indicates diameters, order numbers,
stock status,numbers of teeth, dimensions,
and spare parts for the title product.

is shown on the left hand page of each
double-page spread.
a To Order : For solid-carbide or brazed drills, please specify zorder number and xgrade.
For indexable type drills, please specify zorder number for the drill.
For indexable type drill inserts, please specify zinsert number and xinsert grade.
N000
DRILLING
IDENTIFICATION ...................................... N002
SYMBOL DESCRIPTIONS ....................... N003
DRILLS SELECTION CHART .................. N004
DRILL STANDARD
SOLID CARBIDE
WSTAR DRILLS ........................ N012

WSTAR DRILLS (FOR MACHINING OF STEEL AND CAST IRON) ... N063
WSTAR DRILLS (FOR MACHINING OF STAINLESS STEEL) ... N070
WSTAR DRILLS (FOR MACHINING OF ALUMINIUM ALLOYS) ... N077
WSTAR DRILLS (FOR DIE & MOULD MACHINING) ... N085
MZE/MZS DRILLS ..................... N097
MSE DRILLS ............................. N120
SOLID GUN DRILL ................... N124
MIRACLE DRILLS..................... N127
MAE/MAS DRILLS .................... N129
High-Speed Steel Solid Type
Violet coated precision drills ... N137

VIOLET DRILLS ........................ N162
HSS MILLING SHANK DRILLS... N135
STRAIGHT SHANK DRILLS ..... N166
TAPER SHANK DRILLS ........... N184
TRIANGULAR SHANK DRILLS.... N197
*Arranged
3KD
N125
N197
N206
N205
N208
N202
N204
N200
N204
N256
N254
N254
N183
N166
N184
N195
N178
N176
N191
N246
N174
N189
N180
N192
N129
N129
N252
BRA
BRB
BRL
BRM
BRMB
BRS
BRSB
DCBSS
DCSSM
DCSSS
EPSS
GSD
GTD
GTTD
GWSL
GWSS
GWTS
JFS
KSD
KTD
LSD
LTD
MAE
MAS
MCS
N124
N085
N070
N077
N063
N120
N123
N024
N012
N212
N054
N032
N096
N096
N168
N171
N135
N220
N240
N229
N185
N196
N142
N152
N137
BRAZED TYPE
BRS/BRM/BRK DRILLS ............... N200

BRSB/BRB DRILLS (FOR BRIDGE CONSTRUCTION) .......... N204
BRA/BRL DRILLS ........................ N206
Exchangeable head
TAW DRILLS ................................. N220

INDEXABLE TYPE
MVX TYPE DRILLS ......................

STAW ............................................
TAW ...............................................
TAF TYPE DRILLS .......................
JUST FIT SLEEVE ........................
N212
N220
N229
N240
N246
GUN DRILL GUN REAMER ....... N249

Diamond coated drills ................. N252
MGD
MGS
MHS
MMS
MNS
MQS
MSE
MSP
MVE
MVS
MVX
MWE
MWS
MZE
MZS
SD
SDLS
SEPDM
STAW
TAF
TAW
TD
TTD
VAPDM
VAPDMSUS
VAPDS
N159
N146
N128
N127
N162
N164
VAPDSCB
VAPDSSUS
VCHSM
VCSSS
VSD
VTDS
N001
DRILLING
IDENTIFICATION
PRODUCT CODE OF DRILLS
MW
0300
Product name
Coolant
Diameter
MV : New generation for general-purpose
E : External Coolant
ex.
: 2D
: Straight shank
MW : General-purpose
S : Internal Coolant
0050 | &0.5
: 3D
: Integral shank
0300 | &3.0
: 5D (MAE, MAS : 6D)
MA : MAE/MAS Drills
: 12D
MS : MSE Drills
MZ : MZE/MZS Drills
A
Type of shank
l/d
MN : For Machining of Aluminium Alloys
Diameter
* * * : Shank
(MV Series)
**D: **D
MH : For die & mould machining

MM : For Machining of Stainless Steel
MQ : Steel For high feed cast iron machining
*Other special types can be ordered.
VC S S S D0300
Product name
VC
: Miracle drills
DC
: Diamond coated drills
VA
: Violet coated precision drills
Applications
SD : General-purpose
straight drill
TD : General-purpose
(High Grade, High Speed Steel)

SE
: SE High Precision Drill
DRILLING
(High-Speed Steel)
: For steel
: For high hardness

: For CN
: Violet drills
: TiN coated drills (High-Speed Steel)
PD : For high-precision
: Co-HSS drills
: Blister packed drills
None : High-Speed Steel
machining
U
: For stainless
: For steel frame
W : For deep hole
*Other special types can be ordered.
N002
taper drill
Type of shank Flute length

S : Straight
T
: Taper
3K : Triangular
6K : Hexagonal
***
Diameter
Others
***
**
M
*
S : Short
ex.
: Overall Length
M : Medium
D0050 | & 0.5
: Shank Diameter
L : Long
D0300 | & 3.0
: Taper size
SYMBOL DESCRIPTIONS
Tool material
UWC
HG HSS
CO HSS
CO HSS
D-STH
HSS
Ultra micro grain carbide is used as the substrate

material.
High grade high alloy HSS
High grade high alloy HSS is used as the substrate

material.
Cobalt high speed steel
Cobalt high speed steel is used as the substrate

material.
D-STH cobalt high-speed steel
Cobalt high-speed steel is used as the substrate

material with D-STH.
High speed steel
Coating
DC
V
G
Diamond Coating
Pure Diamond high performance coating excelling

in film adhesion to the substrate.
Violet Coating
Increased tool life of 23 times that of

TiN coated products.
TiN Coating
Increased tool life of 23 times that of

non coated products.
Angle and sharp corner edge

150
Point angle
Indicates drill point angle the tip.
High speed steel is used as the substrate material.
Web thinning
Thinning
Thinning
Thinning
Thinning
X web thinning
X web thinning is used at the drill point.
XR web thinning
XR web thinning is used at the drill point.
C web thinning
C web thinning is used at the drill point.
S web thinning
S web thinning is used at the drill point.
N web thinning
N web thinning is used at the drill point.
DRILLING
Thinning
N003
DRILLING
DRILLS SELECTION CHART CEMENTED CARBIDE

Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
30
NEW
MVS...X30
& 0.5
MWS...LB
5
& 2.95
External
Internal
MVS...X08
Internal
Internal
MVS...X05
Internal
MVS...X03 & 3.0

3
& 20.0
Internal
12
MWS...X20DB
20
& 1.0
MWS...X25DB
25
& 2.95
MWS...X30DB
30
Internal
MWS...XB
N004
N012 N022
N032 N047
N032
Internal
For small Diameter
N024 N030
MVE...X03
MWS...SB
DRILLING
Internal
WSTAR
DRILLS
SERIES
New generation for general-purpose
Solid Drills
MVE...X02
Internal
25
Internal
20
Internal
N012 N022
NEW
MVS...X25
Shape
Cutting
Conditions
Coating
e
Internal
New Generation for small diameter
NEW
MVS...X20
& 1.0
& 2.9
Hardened Steel
Coolant
Hole Depth
12
NEW
MVS...X12
Internal
NEW
MVS...X07
Internal
*S
External
MVS...X02
Page Number
(l/d)
NEW
Internal
Product
Code
Size Range
Drill
Type
(Series Title)
Applications
Tool material
Work Material
P
Dimensions
CARBIDE
N048
N050
N032 N049
CARBIDE
& 3.0
& 20.0
Hardened Steel
Cutting
Conditions
Shape
Dimensions
Non-ferrous Metal
& 3.0
MQS...X8DB
8
& 16.0
3
& 3.0
& 20.0
N032 N047
N032 N050
N063 N067
DRILLING
3
& 3.0
& 20.0
External
MQS...X3DB
Internal
& 3.0
MWS...X30DB
30
& 10.0
Internal
& 3.0
25
MWS...X25DB
& 12.0
Internal
20
Internal
MWS...X20DB
Internal
& 3.0
MWS...X15DB
15
& 14.0
Internal
10
Internal
MWS...X10DB
MMS...X5DB
Internal
& 3.0
MWS...X8DB
8
& 16.0
MMS...X3DB
Internal
MQS...X5DB
Internal
For deep hole

For Machining Of Stainless Steel For Machining Of Steel And Cast Iron
Solid Drills
WSTAR
DRILLS
SERIES
Internal
3
& 3.0
& 25.0
MWS...LB
Internal
MWS...MB
N054 N061
N070 N074
Internal
General Drilling
MWE...MA/MB
Cast Iron
MWE...SA/SB
Page Number
Stainless Steel
Coating
u
(l/d)
Steel
Coolant
Hole Depth
External
Product
Code
Size Range
Drill
Type
(Series Title)
Applications
Tool material
Work Material
P
N005
DRILLING

Hardened Steel
Shape
Cutting
Conditions
Non-ferrous Metal
Stainless Steel
Cast Iron
Steel
Coating
Coolant
Hole Depth
Internal
& 3.0
MNS...X10DB
10
& 14.0
DCSSS
& 0.2
& 2.0
DCSSM
& 2.1
& 3.0
DCBSS
& 0.05
& 3.0
& 1.0
2
MZE...SA/SB
& 20.0
Internal
Internal
& 4.366
& 12.725
N254 N255
N254 N255
External
MCS
Internal
MHS...L020B & 0.95 1

-L300B & 12.0 30
Internal
& 3.0
MNS...X30DB
30
& 10.0
External
20
External
MNS...X20DB
External
N077 N082
MZE...MA
& 3.0
& 20.0
External
Solid Drills
DIAMOND
COATED
DRILLS
for hard brittle materials For non-ferrous material For CFRP For Die & Mould Machining For Machining Of Aluminium Alloys
WSTAR
DRILLS
SERIES
Page Number
(l/d)
MNS...LB
Internal
Product
Code
Size Range
Drill
Type
(Series Title)
Applications
Tool material
Work Material
P
Dimensions
CARBIDE
MZS...MB
& 2.0
& 20.0
MZS...LB
& 1.0
& 20.0
MZS...XB
& 1.0
& 2.9
12
N252 N253
For CFRP
Hard brittle materials

such as ceramics
N085 N093
N256 N257
N006
MZS...SM
Internal
Internal
Internal
N096 N115
N113 N115
2
& 3.4
& 10.3
MZS...MM
External
MZE...MM
External
& 3.4
& 10.3
Internal
MZE...SM
N113 N115
Internal
ZET1
DRILLS
SERIES
With Chamfered Cutting Edges
DRILLING
General Drilling
N096 N115
CARBIDE
Dimensions
N123 N123
N124 N125
N127 N127
N128 N128
Cutting
Conditions
N129 N134
& 14.0
TAWMN(H)
5
& 30.4
TAWLN(H)
3
& 24.5
& 26.7
N229 N238
DRILLING
TAWSN(H)
Internal
Internal
STAWLN
Internal
TAWMB
Shape
N220 N227
STAWMN
TAWSB
Internal
General Drilling
WSTAR
Insert
Type Drill
For Bridge Construction
Exchangeable-head Drills
& 10.0
& 18.4
Internal
STAWSN
Hardened Steel
1.5
STAWSS
Non-ferrous Metal
Cast Iron
MAS...LB
Stainless Steel
& 3.0
MAS...MB
3
& 16.0
Steel
MAE...MB
Coating
Coolant
Hole Depth
& 2.5
& 16.0
VCHSM
N120 N121
External
(3mm shank)
External
& 0.3
& 2.4
Internal
VCSSS
External
100
External
& 0.7
& 3.0
External
MGS...SB
Internal
Internal
Internal
5
12
Internal
Deep Hole Drilling For small Diameter
MSP0300SB
& 0.1
& 0.99
N239 N239
Internal
MAE/MAS
DRILLS
SERIES
Hardened Steel
MIRACLE
DRILLS
SERIES
Aluminium Alloy, Cast Iron
Solid Drills
MGS
GUN DRILL
SERIES
MSE...SB
Page Number
(l/d)
MIRACLE
MINI STAR
DRILL
SERIES
Internal
Product
Code
Size Range
Drill
Type
(Series Title)
Applications
Tool material
Work Material
P
N007
DRILLING
& 2.0
& 30.3
& 6.0
& 30.0
& 6.0
& 30.3
MVX...X2
MVX...X3
MVX...X4
MVX...X5
BRB
& 17.0
& 63.0
MVX...X6
& 17.0
& 43.0
TAF
DRILLS
SERIES
General Drilling
TAFS
& 12.0
& 56.0
TAFM
TAFL
N008
& 16.0
& 34.0
Cutting
Conditions
Hardened Steel
Internal
& 24.5
& 26.7
BRL
Internal
Internal
& 8.0
& 40.0
Non-ferrous Metal
Internal
Internal
Cast Iron
Internal
Internal
BRA
Stainless Steel
Coating
Internal
Internal
& 24.5
& 26.7
Steel
Coolant
Internal
Internal
Hole Depth
Internal
Internal
Internal
BRMB
BRSB
Internal
BRM
Internal
MVX
DRILLS
SERIES
Indexable Drills
DRILLING
GUN REAMER
with
Diamond
Compound
& 14.0
& 30.0
Internal
GUN
REAMER
For Bridge General Drilling General For Bridge Construction

Ultra Deep Holes Ultra Deep Holes Ultra Deep Holes Construction
General Drilling
(For turning) Drilling
GUN
DRILL
New generation for general-purpose
Brazed Drills
BRA/BRL
DRILLS
BRS
Page Number
(l/d)
BRS/BRM
DRILLS
Internal
Product
Code
Size Range
Drill
Type
(Series Title)
Applications
Tool material
Work Material
P
Dimensions
CARBIDE
N200 N201
N202 N203
N204 N205
N204 N205
N206 N210
N208 N210
N249
N250
N251
Shape
N205 N205
N212 N219
N240 N245
WSTAR DRILLS SERIES

SOLID CARBIDE(For small diameter and deep hole)
SOLID CARBIDE
MVE/MVS New generation for general-purpose MGS
SOLID CARBIDE
(General Drilling)
MWE/MWS,MWS.. DB(SUPER LONG )
30
6
5
MVE/MVS
4
3
Hole Depth (l/d)
Hole Depth (l/d)
Hole Depth (l/d)
8
7
MGS
MWS...DB
MWE/MWS
1
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 20
Drill Dia. (mm)
Drill Dia. (mm)
SOLID CARBIDE
SOLID CARBIDE
Drill Dia. (mm)
SOLID CARBIDE
SOLID CARBIDE
MQS Highly efficient drilling, High-precision MMS Highly efficient dril ing,Long tool life MNS Highly efficient drilling MHS High-precision deep hole
10
For machining of aluminium alloys
10
MQS
0
0
10
16
20
3 5
Drill Dia. (mm)
10
350
30
300
20
15
MMS
35
25
Hole Depth (l/d)
(l/d)
Hole Depth (l/d)
Hole Depth (l/d)
For die & mould machining
Neck Length (mm)
For machining of stainless steel
Steel For high feed cast iron machining
MNS
10
20
Drill Dia. (mm)
200
150
MHS
100
50
5
15
250
10
14
Drill Dia. (mm)
0
0.95
10 12
Drill Dia. (mm)
Indexable carbide drills

INDEXABLE TYPE
INDEXABLE HEAD
STAW,TAW
DRILLING
MVX
7
Hole Depth (l/d)
Hole Depth (l/d)
STAW
MVX
&17-& 33
l/d=2,3,4,5,6
& 33.5-& 63.0

l/d=2,3,4,5,6
STAW
TAW
& 14-&33
l/d=3,5,8
l/d=3,5
STAW
l/d=1.5
1
0
l/d=8
10
17 20
30 33
44
63
15.5 18.4
Drill Dia. (mm)
Drill Dia. (mm)
N009
DRILLING
DRILLS SELECTION CHART HSS
N010
& 0.25
& 5.95
(1/100 Straight)
SDLS
& 1.0
& 10.0
KSD
& 1.0
& 13.0
Non-ferrous Metal
Hardened Steel
N166 N198
N168 N199
N170 N199
Cutting
Conditions
Tool material
Cast Iron
SD
Stainless Steel
& 0.2
& 17.5
Steel
SD
Coating
& 0.5
& 13.0
Coolant
GSD
External
& 0.5
& 4.0
External
SEPDM
External
& 6.0
& 32.0
External
VTDS
External
& 0.5
& 13.0
External
VSD
External
& 3.0
& 32.0
External
VAPDSCB
External
& 0.5
& 13.0
External
VAPDMSUS
External
& 0.5
& 20.0
Page Number
External
VAPDSSUS
External
& 0.5
& 32.0
High Grade,
High Speed Steel
VAPDM
Cobalt High
Speed Steel
& 0.5
& 13.0
High Speed
High Grade,
High Speed Steel
Steel
High Speed Steel
Size Range
VAPDS
High Speed Steel
General Drilling
Product
Code
Cobalt High High Speed

Steel
Speed Steel
DRILLING
STRAIGHT
SHANK
DRILL
General
Drilling
SE High
Precision
Drill
General Drilling
VIOLET
DRILL
General Deep Hole

Drilling Drilling
VIOLET
COATED
DRILLS
Spot
General,
Milling High Precision Steel
General,
High Precision
Drill
Type
(Series Title)
Applications
Work Material
P
Dimensions
HSS
N137 N141
N142 N145
N146 N158
N152 N158
N159 N161
N162 N163
N164 N165
Shape
N135 N136
N171 N173
N174 N199
TAPER
SHANK
DRILL
TRIANGULAR
SHANK DRILL
Sheet
Steel
Deep Hole Drilling
& 2.0
& 13.0
LSD
& 1.0
& 13.0
EPSS
& 2.0
& 13.0
GTD
& 6.0
& 40.0
TD
& 3.0
& 75.0
KTD
& 5.0
& 50.0
GWTS
& 6.0
& 32.0
LTD
& 6.0
& 40.0
GTTD
& 17.0
& 32.0
TTD
& 17.0
& 32.0
3KD
& 7.0
& 26.0
Steel
Stainless Steel
Cast Iron
Non-ferrous Metal
u
u
N176 N198
External
G
e
u
u
u
N178 N198
External
u
u
u
N180 N199
External
u
u
u
u
N183
External
G
e
u
u
u
N184 N198
External
e
u
u
u
N185 N199
External
e
u
u
u
N189 N199
External
G
e
u
u
u
N191 N198
External
u
u
u
N192
G
e
N195 N198
N196 N199
K
N
S
H
Hardened Steel
Coating
External
M
Coolant
External
External
Tool material
Size Range
External
Cobalt High
Speed Steel
GWSL
High Speed High Speed

Steel
Steel
& 1.0
& 13.0
High Speed
Steel
GWSS
High Speed High Speed High Speed High Speed Cobalt High Cobalt High
Steel
Steel
Steel
Steel
Speed Steel Speed Steel
Applications
Product
Code
P
u
u
Shape
N197
Cutting
Conditions
Dimensions
Work Material
DRILLING
General Drilling
STRAIGHT
SHANK
DRILL
For steel frame Deep Hole Drilling
Drill
Type
(Series Title)
For General-purpose
Electric Drills
HSS
Page Number
N011
Steel
Product Code
1 < DC < 2.9
Other than MVS-X02
+ 0.014
0
0
0.014
Product Code
DCON
MVS-X02-
h6
LF
145
DC
PL
LCF
LH
LF
145
DC
Type1
Type2
Type3
Type4
OAL
PL
LCF
LH
OAL
PL
LF
140
DC
0
0.006
MVS
DCON(h6)
DCON(h6)
a Linear tooth profile improves both chip discharge and cutting edge strength.
a Double margin specifications offer optimum balance and high precision with small drills
DCON(h6)
MVS
for small diameter

WSTAR DRILLS
DCON(h6)
CARBIDE
LCF
LH
OAL
LF
140
DC
PL
LCF
LH
OAL
25
30
*S
7
12
20
25
30
*S
7
12
20
25
30
DRILLING
1.2
1.3
55
0.2
15.2 19.2 55.2
55
0.2
24.2 28.2 60.2
60
0.2
28.2 32.2 66.2

33.2 37.2 72.2
66
72
0.2
0.2
3
3
5.6 9.1 55.2

11.2 15.2 55.2
55
55
0.2
0.2
17.2 21.2 55.2
55
25.2 29.2 60.2
60
12
20
3
3
25
30
3
3
1
3
*S
7
0.2
12
0.2
20
a
a
1.5
31.2 34.2 66.2

36.2 40.2 72.2
66
72
0.2
0.2
3
3
3
3
25
30
6.2 9.6 55.2

12.2 15.2 55.2
55
55
0.2
0.2
3
3
1
3
*S
7
18.2 21.2 55.2
55
0.2
12
28.2 31.2 60.2
60
0.2
20
34.2 37.2 66.2

40.2 43.2 72.2
66
72
0.2
0.2
3
3
3
3
25
30
6.6 9.8 55.2

13.2 16.2 55.2
55
55
0.2
0.2
3
3
1
3
*S
7
20.2 23.2 55.2
55
0.2
12
20
25
30
30.2 33.2 68.2
68
0.2
36.2 40.2 74.2

43.2 46.2 82.2
74
82
0.2
0.2
3
3
3
3

N012
1.4
1.6
1.7
MVS0140X02S030
MVS0140X07S030
MVS0140X12S030
MVS0140X20S030
MVS0140X25S030
MVS0140X30S030
MVS0150X02S030
MVS0150X07S030
MVS0150X12S030
MVS0150X20S030
MVS0150X25S030
MVS0150X30S030
MVS0160X02S030
MVS0160X07S030
MVS0160X12S030
MVS0160X20S030
MVS0160X25S030
MVS0160X30S030
MVS0170X02S030
MVS0170X07S030
MVS0170X12S030
MVS0170X20S030
MVS0170X25S030
MVS0170X30S030
DCON
10.2 14.2 55.2
*S
7
PL
20
LF
12
1.1
OAL
0.2
Type
7.2 10.2 55.2

14.3 17.3 55.3
55
55
0.2
0.3
3
3
1
3
21.3 24.3 55.3
55
0.3
32.3 35.3 68.3
68
0.3
39.3 42.3 74.3

46.3 49.3 82.3
74
82
0.3
0.3
3
3
3
3
7.6 10.4 55.2

15.3 18.3 55.3
55
55
0.2
0.3
3
3
1
3
23.3 26.3 55.3
55
0.3
35.3 37.3 68.3
68
0.3
42.3 45.3 74.3

50.3 52.3 82.3
74
82
0.3
0.3
3
3
3
3
8.3 10.9 68.3

16.3 19.3 68.3
68
68
0.3
0.3
3
3
1
3
24.3 27.3 68.3
68
0.3
37.3 39.3 78.3
78
0.3
45.3 47.3 86.3

53.3 55.3 95.3
86
95
0.3
0.3
3
3
3
3
8.7 11.1 68.3

17.3 19.3 68.3
68
68
0.3
0.3
3
3
1
3
26.3 28.3 68.3
68
0.3
39.3 42.3 78.3
78
0.3
48.3 50.3 86.3

56.3 59.3 95.3
86
95
0.3
0.3
3
3
3
3
LH
*S
7
55
Order Number
LCF
8.9 55.2
(mm) (l/d)
Dimensions (mm)
Stock
DP1020
25
30
5.2
DC
Hole Depth
DCON
20
PL
12
Type
LF
MVS0100X02S030
MVS0100X07S030
MVS0100X12S030
MVS0100X20S030
MVS0100X25S030
MVS0100X30S030
MVS0110X02S030
MVS0110X07S030
MVS0110X12S030
MVS0110X20S030
MVS0110X25S030
MVS0110X30S030
MVS0120X02S030
MVS0120X07S030
MVS0120X12S030
MVS0120X20S030
MVS0120X25S030
MVS0120X30S030
MVS0130X02S030
MVS0130X07S030
MVS0130X12S030
MVS0130X20S030
MVS0130X25S030
MVS0130X30S030
OAL
Order Number
LH
*S
1.0
Dimensions (mm)
LCF
(mm) (l/d)
DC
Internal Coolant
Stock
DP1020
Hole Depth
Internal Coolant
CARBIDE
2.0
2.1
2.2
2.3
2.4
2.5
12
20
25
30
*S
7
12
20
25
30
*S
7
12
20
25
30
*S
7
12
20
25
30
*S
7
12
20
25
30
*S
7
12
20
25
30
*S
7
12
20
25
30
*S
7
12
20
25
30
MVS0180X02S030
MVS0180X07S030
MVS0180X12S030
MVS0180X20S030
MVS0180X25S030
MVS0180X30S030
MVS0190X02S030
MVS0190X07S030
MVS0190X12S030
MVS0190X20S030
MVS0190X25S030
MVS0190X30S030
MVS0200X02S030
MVS0200X07S030
MVS0200X12S030
MVS0200X20S030
MVS0200X25S030
MVS0200X30S030
MVS0210X02S030
MVS0210X07S030
MVS0210X12S030
MVS0210X20S030
MVS0210X25S030
MVS0210X30S030
MVS0220X02S030
MVS0220X07S030
MVS0220X12S030
MVS0220X20S030
MVS0220X25S030
MVS0220X30S030
MVS0230X02S030
MVS0230X07S030
MVS0230X12S030
MVS0230X20S030
MVS0230X25S030
MVS0230X30S030
MVS0240X02S030
MVS0240X07S030
MVS0240X12S030
MVS0240X20S030
MVS0240X25S030
MVS0240X30S030
MVS0250X02S030
MVS0250X07S030
MVS0250X12S030
MVS0250X20S030
MVS0250X25S030
MVS0250X30S030
50.3 53.3 94.3 94 0.3

59.3 62.3 102.3 102 0.3
3
3
9.7 11.8 68.3

19.3 21.3 68.3
68 0.3
68 0.3
29.3 31.3 68.3

44.3 46.3 84.3
20
3
3
25
30
3
3
1
3
*S
7
68 0.3
12
84 0.3
20
53.3 55.3 94.3 94 0.3

63.3 65.3 102.3 102 0.3
3
3
3
3
25
30
10.3 12.2 68.3

20.4 22.4 68.4
68 0.3
68 0.4
3
3
1
3
*S
7
30.4 32.4 68.4
68 0.4
12
46.4 48.4 84.4
84 0.4
20
56.4 58.4 94.4 94 0.4

66.4 68.4 102.4 102 0.4
3
3
3
3
25
30
10.7 12.4 74.3

21.4 23.4 74.4
74 0.3
74 0.4
3
3
1
3
*S
7
32.4 34.4 74.4
74 0.4
12
48.4 50.4 94.4
94 0.4
20
59.4 60.4 107.4 107 0.4

69.4 71.4 118.4 118 0.4
3
3
3
3
25
30
11.3 12.8 74.3

22.4 23.4 74.4
74 0.3
74 0.4
3
3
1
3
33.4 34.4 74.4
74 0.4
51.4 52.4 94.4
94 0.4
62.4 63.4 107.4 107 0.4

73.4 74.4 118.4 118 0.4
3
3
3
3
11.8 13.1 74.4

23.4 24.4 74.4
74 0.4
74 0.4
3
3
1
3
35.4 36.4 74.4
74 0.4
53.4 54.4 94.4
94 0.4
64.4 66.4 107.4 107 0.4

76.4 77.4 118.4 118 0.4
3
3
3
3
12.4 13.5 74.4

24.4 25.4 74.4
74 0.4
74 0.4
3
3
1
3
36.4 37.4 74.4
74 0.4
55.4 56.4 94.4
94 0.4
67.4 68.4 107.4 107 0.4

79.4 80.4 118.4 118 0.4
3
3
3
3
12.8 13.7 74.4

25.5 26.5 74.5
74 0.4
74 0.5
3
3
1
3
38.5 39.5 74.5
74 0.5
58.5 59.5 94.5
94 0.5
70.5 71.5 107.5 107 0.5

83.5 84.5 118.5 118 0.5
3
3
3
3
2.7
2.8
2.9
PL
MVS0260X02S030
MVS0260X07S030
MVS0260X12S030
MVS0260X20S030
MVS0260X25S030
MVS0260X30S030
MVS0270X02S030
MVS0270X07S030
MVS0270X12S030
MVS0270X20S030
MVS0270X25S030
MVS0270X30S030
MVS0280X02S030
MVS0280X07S030
MVS0280X12S030
MVS0280X20S030
MVS0280X25S030
MVS0280X30S030
MVS0290X02S030
MVS0290X07S030
MVS0290X12S030
MVS0290X20S030
MVS0290X25S030
MVS0290X30S030
LF
84 0.3
12
2.6
OAL
41.3 44.3 84.3
LH
*S
7
Order Number
LCF
(mm) (l/d)
DP1020
68 0.3
Hole Depth
27.3 29.3 68.3
PL
1
3
LF
3
3
OAL
68 0.3
68 0.3
LH
9.3 11.5 68.3

18.3 20.3 68.3
DC
13.4 13.4 81.4

26.5 26.5 81.5
81 0.4
81 0.5
39.5 39.5 81.5
DCON
Type
Dimensions (mm)
Stock
Type
3
3
2
4
81 0.5
60.5 60.5 103.5 103 0.5
73.5 73.5 117.5 117 0.5

86.5 86.5 132.5 132 0.5
3
3
4
4
13.8 13.8 81.4

27.5 27.5 81.5
81 0.4
81 0.5
3
3
2
4
41.5 41.5 81.5
81 0.5
62.5 62.5 103.5 103 0.5
76.5 76.5 117.5 117 0.5

89.5 89.5 132.5 132 0.5
3
3
4
4
14.4 14.4 81.4

28.5 28.5 81.5
81 0.4
81 0.5
3
3
2
4
42.5 42.5 81.5
81 0.5
64.5 64.5 103.5 103 0.5
78.5 78.5 117.5 117 0.5

92.5 92.5 132.5 132 0.5
3
3
4
4
14.9 14.9 81.5

29.5 29.5 81.5
81 0.5
81 0.5
3
3
2
4
44.5 44.5 81.5
81 0.5
67.5 67.5 103.5 103 0.5
81.5 81.5 117.5 117 0.5

96.5 96.5 132.5 132 0.5
3
3
4
4
DRILLING
1.9
*S
7
Order Number
DCON
1.8
Internal Coolant
Dimensions (mm)
LCF
(mm) (l/d)
DP1020
DC
Hole Depth
Internal Coolant
Stock

CUTTING CONDITIONS
TECHNICAL DATA
N022
Q001
N013
MVS
WSTAR DRILLS
M
Steel
DC=3
0
0.014
0
0.006
h6
3<DC < 6 6<DC < 10 10<DC < 1818<DC < 20

0
0.018
0
0.008
0
0.027
0
0.011
0
0.033
0
0.013
LF
140
DC(h8)
PL
0
0.022
0
0.009
LCF
LH
DCON(h6)
a New grade DP1020 offers long tool life for a wide range of work materials.
a Unique coolant supply technology, TRI-cooling offers high machining efficiency. (on drills over 6)
Type1
DCON(h6)
CARBIDE
Type2
OAL
LF
140
DC(h8)
PL
LCF
LH
OAL
3.4
3.5
8
8
a
a
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
4
6
2
1
3
3
28.5 28.5 81.5
81
0.5
28.5 31.7 81.5
81
0.5
35.5 35.5 81.5

35.5 38.7 81.5
81
81
0.5
0.5
3
6
21.6 23.6 76.6

21.6 24.7 76.6
76
76
0.6
0.6
32.6 32.6 87.6
87
0.6
LH
N014
3.6
3.7
32.6 35.7 87.6
87
0.6
41.6 41.6 87.6

41.6 44.7 87.6
87
87
0.6
0.6
4
6
2
1
8
8
21.6 23.6 76.6

21.6 24.6 76.6
76
76
0.6
0.6
4
6
2
1
3
3
32.6 32.6 87.6
87
0.6
32.6 35.6 87.6
87
0.6
41.6 41.6 87.6

41.6 44.6 87.6
87
87
0.6
0.6
4
6
2
1
8
8
21.6 23.6 76.6

21.6 24.5 76.6
76
76
0.6
0.6
4
6
2
1
3
3
32.6 32.6 87.6
87
0.6
32.6 35.5 87.6
87
0.6
41.6 41.6 87.6

41.6 44.5 87.6
87
87
0.6
0.6
4
6
2
1
8
8
21.6 23.6 76.6

21.6 24.4 76.6
76
76
0.6
0.6
4
6
2
1
3
3
32.6 32.6 87.6
87
0.6
32.6 35.4 87.6
87
0.6
41.6 41.6 87.6

41.6 44.4 87.6
87
87
0.6
0.6
4
6
2
1
8
8
21.6 23.6 76.6

21.6 24.3 76.6
76
76
0.6
0.6
4
6
2
1
3
3
32.6 32.6 87.6
87
0.6
32.6 35.3 87.6
87
0.6
41.6 41.6 87.6

41.6 44.3 87.6
87
87
0.6
0.6
4
6
2
1
8
8
3.8
3.9
4.0
4.1
23.7 23.7 80.7

23.7 26.3 80.7
80 0.7
80 0.7
4
6
2
1
36.7 36.7 92.7
92 0.7
36.7 39.3 92.7
92 0.7
46.7 46.7 92.7

46.7 49.3 92.7
92 0.7
92 0.7
4
6
2
1
23.7 23.7 80.7

23.7 26.2 80.7
80 0.7
80 0.7
4
6
2
1
36.7 36.7 92.7
92 0.7
36.7 39.2 92.7
92 0.7
46.7 46.7 92.7

46.7 49.2 92.7
92 0.7
92 0.7
4
6
2
1
23.7 23.7 80.7

23.7 26.1 80.7
80 0.7
80 0.7
4
6
2
1
36.7 36.7 92.7
92 0.7
36.7 39.1 92.7
92 0.7
46.7 46.7 92.7

46.7 49.1 92.7
92 0.7
92 0.7
4
6
2
1
23.7 23.7 80.7

23.7 26.0 80.7
80 0.7
80 0.7
4
6
2
1
36.7 36.7 92.7
92 0.7
36.7 39.0 92.7
92 0.7
46.7 46.7 92.7

46.7 49.0 92.7
92 0.7
92 0.7
4
6
2
1
23.7 23.7 80.7

23.7 25.8 80.7
80 0.7
80 0.7
4
6
2
1
36.7 36.7 92.7
92 0.7
36.7 38.8 92.7
92 0.7
46.7 46.7 92.7

46.7 48.8 92.7
92 0.7
92 0.7
4
6
2
1
25.7 25.7 86.7

25.7 27.7 86.7
86 0.7
86 0.7
5
6
2
1
40.7 40.7 100.7 100 0.7
40.7 42.7 100.7 100 0.7
52.7 52.7 100.7 100 0.7

52.7 54.7 100.7 100 0.7
5
6
2
1
PL
8
8
LF
2
1
0.5
OAL
0.5
72
LH
72
21.5 24.7 72.5
(mm) (l/d)
Type
LCF
MVS0360X03S040
MVS0360X03S060
MVS0360X05S040
MVS0360X05S060
MVS0360X08S040
MVS0360X08S060
MVS0370X03S040
MVS0370X03S060
MVS0370X05S040
MVS0370X05S060
MVS0370X08S040
MVS0370X08S060
MVS0380X03S040
MVS0380X03S060
MVS0380X05S040
MVS0380X05S060
MVS0380X08S040
MVS0380X08S060
MVS0390X03S040
MVS0390X03S060
MVS0390X05S040
MVS0390X05S060
MVS0390X08S040
MVS0390X08S060
MVS0400X03S040
MVS0400X03S060
MVS0400X05S040
MVS0400X05S060
MVS0400X08S040
MVS0400X08S060
MVS0410X03S050
MVS0410X03S060
MVS0410X05S050
MVS0410X05S060
MVS0410X08S050
MVS0410X08S060
21.5 21.5 72.5
Hole Depth
DCON
3
3
PL
MVS0300X03S030
MVS0300X03S060
MVS0300X05S030
MVS0300X05S060
MVS0300X08S030
MVS0300X08S060
MVS0310X03S040
MVS0310X03S060
MVS0310X05S040
MVS0310X05S060
MVS0310X08S040
MVS0310X08S060
MVS0320X03S040
MVS0320X03S060
MVS0320X05S040
MVS0320X05S060
MVS0320X08S040
MVS0320X08S060
MVS0330X03S040
MVS0330X03S060
MVS0330X05S040
MVS0330X05S060
MVS0330X08S040
MVS0330X08S060
MVS0340X03S040
MVS0340X03S060
MVS0340X05S040
MVS0340X05S060
MVS0340X08S040
MVS0340X08S060
MVS0350X03S040
MVS0350X03S060
MVS0350X05S040
MVS0350X05S060
MVS0350X08S040
MVS0350X08S060
DC
DCON
DRILLING
3.3
DP1020
3.2
Dimensions (mm)
Stock
Order Number
Type
LF
3.1
Order Number
OAL
3.0
Internal Coolant
Dimensions (mm)
LCF
(mm) (l/d)
DP1020
DC
Hole Depth
Internal Coolant
Stock
CARBIDE
4.6
4.7
4.8
4.9
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
2
1
8
8
5
6
2
1
40.8 40.8 100.8 100 0.8
3
5.1 5
8
40.8 42.6 100.8 100 0.8
52.8 52.8 100.8 100 0.8

52.8 54.6 100.8 100 0.8
5
6
2
1
5.2 5
25.8 25.8 86.8

25.8 27.5 86.8
86 0.8
86 0.8
5
6
2
1
40.8 40.8 100.8 100 0.8
3
5.3 5
8
40.8 42.5 100.8 100 0.8
52.8 52.8 100.8 100 0.8

52.8 54.5 100.8 100 0.8
5
6
2
1
3
5.4 5
8
25.8 25.8 86.8

25.8 27.4 86.8
86 0.8
86 0.8
5
6
2
1
40.8 40.8 100.8 100 0.8
3
5.5 5
8
40.8 42.4 100.8 100 0.8
52.8 52.8 100.8 100 0.8

52.8 54.4 100.8 100 0.8
5
6
2
1
3
5.6 5
8
28.3 28.3 90.8

28.3 31.3 90.8
90 0.8
90 0.8
5
6
2
2
5.7 5
44.8 44.8 105.8 105 0.8
44.8 47.8 105.8 105 0.8
57.8 57.8 105.8 105 0.8

57.8 60.8 105.8 105 0.8
5
6
2
2
3
5.8 5
8
28.4 28.4 90.9

28.4 31.4 90.9
90 0.9
90 0.9
5
6
2
2
5.9 5
44.9 44.9 105.9 105 0.9
44.9 47.9 105.9 105 0.9
57.9 57.9 105.9 105 0.9

57.9 60.9 105.9 105 0.9
5
6
2
2
3
6.0 5
8
28.4 28.4 90.9

28.4 31.4 90.9
90 0.9
90 0.9
5
6
2
2
3
3
44.9 44.9 105.9 105 0.9
44.9 47.9 105.9 105 0.9
57.9 57.9 105.9 105 0.9

57.9 60.9 105.9 105 0.9
5
6
2
2
8
8
28.4 28.4 90.9

28.4 31.4 90.9
90 0.9
90 0.9
5
6
2
2
3
3
44.9 44.9 105.9 105 0.9
44.9 47.9 105.9 105 0.9
57.9 57.9 105.9 105 0.9

57.9 60.9 105.9 105 0.9
5
6
2
2
8
8
52.8 52.8 100.8 100 0.8

52.8 54.7 100.8 100 0.8
5
6
25.8 25.8 86.8

25.8 27.6 86.8
86 0.8
86 0.8
PL
LF
OAL
40.8 42.7 100.8 100 0.8
LH
5.0
6.1
6.2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
90 0.9
90 0.9
5
6
2
2
44.9 44.9 105.9 105 0.9
44.9 47.9 105.9 105 0.9
57.9 57.9 105.9 105 0.9

57.9 60.9 105.9 105 0.9
5
6
2
2
28.4 30.9 82.9 82 0.9

44.9 48.9 100.9 100 0.9
61.9 66.9 118.9 118 0.9
6
6
6
2
2
2
28.4 30.9 82.9 82 0.9

44.9 48.9 100.9 100 0.9
61.9 66.9 118.9 118 0.9
6
6
6
2
2
2
28.5 31.0 83.0 82 1.0

45.0 49.0 101.0 100 1.0
62.0 67.0 119.0 118 1.0
6
6
6
2
2
2
28.5 31.0 83.0 82 1.0

45.0 49.0 101.0 100 1.0
62.0 67.0 119.0 118 1.0
6
6
6
2
2
2
28.5 31.0 83.0 82 1.0

45.0 49.0 101.0 100 1.0
62.0 67.0 119.0 118 1.0
6
6
6
2
2
2
31.0 31.0 83.0 82 1.0

49.0 49.0 101.0 100 1.0
67.0 67.0 119.0 118 1.0
6
6
6
2
2
2
31.0 31.0 83.0 82 1.0

49.0 49.0 101.0 100 1.0
67.0 67.0 119.0 118 1.0
6
6
6
2
2
2
31.1 31.1 83.1 82 1.1

49.1 49.1 101.1 100 1.1
67.1 67.1 119.1 118 1.1
6
6
6
2
2
2
31.1 31.1 83.1 82 1.1

49.1 49.1 101.1 100 1.1
67.1 67.1 119.1 118 1.1
6
6
6
2
2
2
31.1 31.1 83.1 82 1.1

49.1 49.1 101.1 100 1.1
67.1 67.1 119.1 118 1.1
6
6
6
2
2
2
33.6 36.1 89.1

33.6 36.1 89.1
88 1.1
88 1.1
7
8
2
2
53.1 57.1 110.1 109 1.1
53.1 57.1 110.1 109 1.1
73.1 78.1 131.1 130 1.1

73.1 78.1 131.1 130 1.1
7
8
2
2
33.6 36.1 89.1

33.6 36.1 89.1
88 1.1
88 1.1
7
8
2
2
53.1 57.1 110.1 109 1.1
53.1 57.1 110.1 109 1.1
73.1 78.1 131.1 130 1.1

73.1 78.1 131.1 130 1.1
7
8
2
2
28.4 28.4 90.9

28.4 31.4 90.9
CUTTING CONDITIONS
TECHNICAL DATA
PL
LF
40.8 40.8 100.8 100 0.8
(mm) (l/d)
OAL
MVS0500X03S050
MVS0500X03S060
MVS0500X05S050
MVS0500X05S060
MVS0500X08S050
MVS0500X08S060
MVS0510X03S060
MVS0510X05S060
MVS0510X08S060
MVS0520X03S060
MVS0520X05S060
MVS0520X08S060
MVS0530X03S060
MVS0530X05S060
MVS0530X08S060
MVS0540X03S060
MVS0540X05S060
MVS0540X08S060
MVS0550X03S060
MVS0550X05S060
MVS0550X08S060
MVS0560X03S060
MVS0560X05S060
MVS0560X08S060
MVS0570X03S060
MVS0570X05S060
MVS0570X08S060
MVS0580X03S060
MVS0580X05S060
MVS0580X08S060
MVS0590X03S060
MVS0590X05S060
MVS0590X08S060
MVS0600X03S060
MVS0600X05S060
MVS0600X08S060
MVS0610X03S070
MVS0610X03S080
MVS0610X05S070
MVS0610X05S080
MVS0610X08S070
MVS0610X08S080
MVS0620X03S070
MVS0620X03S080
MVS0620X05S070
MVS0620X05S080
MVS0620X08S070
MVS0620X08S080
2
1
LH
5
6
Type
LCF
Hole Depth
3
3
86 0.8
86 0.8
25.8 25.8 86.8

25.8 27.7 86.8
DC
N022
Q001
DRILLING
4.5
Type
DCON
4.4
MVS0420X03S050
MVS0420X03S060
MVS0420X05S050
MVS0420X05S060
MVS0420X08S050
MVS0420X08S060
MVS0430X03S050
MVS0430X03S060
MVS0430X05S050
MVS0430X05S060
MVS0430X08S050
MVS0430X08S060
MVS0440X03S050
MVS0440X03S060
MVS0440X05S050
MVS0440X05S060
MVS0440X08S050
MVS0440X08S060
MVS0450X03S050
MVS0450X03S060
MVS0450X05S050
MVS0450X05S060
MVS0450X08S050
MVS0450X08S060
MVS0460X03S050
MVS0460X03S060
MVS0460X05S050
MVS0460X05S060
MVS0460X08S050
MVS0460X08S060
MVS0470X03S050
MVS0470X03S060
MVS0470X05S050
MVS0470X05S060
MVS0470X08S050
MVS0470X08S060
MVS0480X03S050
MVS0480X03S060
MVS0480X05S050
MVS0480X05S060
MVS0480X08S050
MVS0480X08S060
MVS0490X03S050
MVS0490X03S060
MVS0490X05S050
MVS0490X05S060
MVS0490X08S050
MVS0490X08S060
DP1020
4.3
3
3
Dimensions (mm)
Stock
Order Number
DCON
4.2
Order Number
LCF
(mm) (l/d)
Internal Coolant
Dimensions (mm)
DP1020
DC
Hole Depth
Internal Coolant
Stock
N015
MVS
WSTAR DRILLS
6.7
DRILLING
6.8
6.9
7.0
N016
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
53.1 57.1 110.1 109 1.1
73.1 78.1 131.1 130 1.1

73.1 78.1 131.1 130 1.1
7
8
2
2
7.2 5
33.7 36.2 89.2

33.7 36.2 89.2
88 1.2
88 1.2
7
8
2
2
53.2 57.2 110.2 109 1.2
3
7.3 5
8
a
a
53.2 57.2 110.2 109 1.2
73.2 78.2 131.2 130 1.2

73.2 78.2 131.2 130 1.2
7
8
2
2
7.4 5
33.7 36.2 89.2

33.7 36.2 89.2
88 1.2
88 1.2
7
8
2
2
53.2 57.2 110.2 109 1.2
3
7.5 5
8
53.2 57.2 110.2 109 1.2
73.2 78.2 131.2 130 1.2

73.2 78.2 131.2 130 1.2
7
8
2
2
3
7.6 5
8
36.2 36.2 89.2

36.2 38.2 89.2
88 1.2
88 1.2
7
8
2
2
57.2 57.2 110.2 109 1.2
3
7.7 5
8
57.2 59.2 110.2 109 1.2
78.2 78.2 131.2 130 1.2

78.2 80.2 131.2 130 1.2
7
8
2
2
3
7.8 5
8
36.2 36.2 89.2

36.2 38.2 89.2
88 1.2
88 1.2
7
8
2
2
7.9 5
57.2 57.2 110.2 109 1.2
57.2 59.2 110.2 109 1.2
78.2 78.2 131.2 130 1.2

78.2 80.2 131.2 130 1.2
7
8
2
2
3
8.0 5
8
36.2 36.2 89.2

36.2 38.2 89.2
88 1.2
88 1.2
7
8
2
2
3
3
57.2 57.2 110.2 109 1.2
57.2 59.2 110.2 109 1.2
78.2 78.2 131.2 130 1.2

78.2 80.2 131.2 130 1.2
7
8
2
2
8
8
36.3 36.3 89.3

36.3 38.3 89.3
88 1.3
88 1.3
7
8
2
2
3
3
57.3 57.3 110.3 109 1.3
57.3 59.3 110.3 109 1.3
78.3 78.3 131.3 130 1.3

78.3 80.3 131.3 130 1.3
7
8
2
2
8
8
36.3 36.3 89.3

36.3 38.3 89.3
88 1.3
88 1.3
7
8
2
2
3
3
57.3 57.3 110.3 109 1.3
57.3 59.3 110.3 109 1.3
78.3 78.3 131.3 130 1.3

78.3 80.3 131.3 130 1.3
7
8
2
2
8
8
8.1
8.2
8.3
a
a
a
a
a
a
a
a
a
a
38.8 41.3 95.3 94 1.3

61.3 65.3 119.3 118 1.3
84.3 89.3 143.3 142 1.3
8
8
8
2
2
2
38.8 41.3 95.3 94 1.3

61.3 65.3 119.3 118 1.3
84.3 89.3 143.3 142 1.3
8
8
8
2
2
2
38.8 41.3 95.3 94 1.3

61.3 65.3 119.3 118 1.3
84.3 89.3 143.3 142 1.3
8
8
8
2
2
2
38.8 41.3 95.3 94 1.3

61.3 65.3 119.3 118 1.3
84.3 89.3 143.3 142 1.3
8
8
8
2
2
2
38.9 41.4 95.4 94 1.4

61.4 65.4 119.4 118 1.4
84.4 89.4 143.4 142 1.4
8
8
8
2
2
2
41.4 41.4 95.4 94 1.4

65.4 65.4 119.4 118 1.4
89.4 89.4 143.4 142 1.4
8
8
8
2
2
2
41.4 41.4 95.4 94 1.4

65.4 65.4 119.4 118 1.4
89.4 89.4 143.4 142 1.4
8
8
8
2
2
2
41.4 41.4 95.4 94 1.4

65.4 65.4 119.4 118 1.4
89.4 89.4 143.4 142 1.4
8
8
8
2
2
2
41.4 41.4 95.4 94 1.4

65.4 65.4 119.4 118 1.4
89.4 89.4 143.4 142 1.4
8
8
8
2
2
2
41.5 41.5 95.5 94 1.5

65.5 65.5 119.5 118 1.5
89.5 89.5 143.5 142 1.5
8
8
8
2
2
2
44.0 46.5 101.5 100 1.5 9

44.0 46.5 101.5 100 1.5 10
2
2
LF
53.1 57.1 110.1 109 1.1
MVS0710X03S080
MVS0710X05S080
MVS0710X08S080
MVS0720X03S080
MVS0720X05S080
MVS0720X08S080
MVS0730X03S080
MVS0730X05S080
MVS0730X08S080
MVS0740X03S080
MVS0740X05S080
MVS0740X08S080
MVS0750X03S080
MVS0750X05S080
MVS0750X08S080
MVS0760X03S080
MVS0760X05S080
MVS0760X08S080
MVS0770X03S080
MVS0770X05S080
MVS0770X08S080
MVS0780X03S080
MVS0780X05S080
MVS0780X08S080
MVS0790X03S080
MVS0790X05S080
MVS0790X08S080
MVS0800X03S080
MVS0800X05S080
MVS0800X08S080
MVS0810X03S090
MVS0810X03S100
MVS0810X05S090
MVS0810X05S100
MVS0810X08S090
MVS0810X08S100
MVS0820X03S090
MVS0820X03S100
MVS0820X05S090
MVS0820X05S100
MVS0820X08S090
MVS0820X08S100
MVS0830X03S090
MVS0830X03S100
MVS0830X05S090
MVS0830X05S100
MVS0830X08S090
MVS0830X08S100
OAL
(mm) (l/d)
Type
LH
Hole Depth
PL
7.1 5
LF
2
2
OAL
7
8
LH
88 1.1
88 1.1
33.6 36.1 89.1

33.6 36.1 89.1
DCON
6.6
Order Number
DC
PL
6.5
MVS0630X03S070
MVS0630X03S080
MVS0630X05S070
MVS0630X05S080
MVS0630X08S070
MVS0630X08S080
MVS0640X03S070
MVS0640X03S080
MVS0640X05S070
MVS0640X05S080
MVS0640X08S070
MVS0640X08S080
MVS0650X03S070
MVS0650X03S080
MVS0650X05S070
MVS0650X05S080
MVS0650X08S070
MVS0650X08S080
MVS0660X03S070
MVS0660X03S080
MVS0660X05S070
MVS0660X05S080
MVS0660X08S070
MVS0660X08S080
MVS0670X03S070
MVS0670X03S080
MVS0670X05S070
MVS0670X05S080
MVS0670X08S070
MVS0670X08S080
MVS0680X03S070
MVS0680X03S080
MVS0680X05S070
MVS0680X05S080
MVS0680X08S070
MVS0680X08S080
MVS0690X03S070
MVS0690X03S080
MVS0690X05S070
MVS0690X05S080
MVS0690X08S070
MVS0690X08S080
MVS0700X03S070
MVS0700X03S080
MVS0700X05S070
MVS0700X05S080
MVS0700X08S070
MVS0700X08S080
Type
DP1020
6.4
3
3
Dimensions (mm)
Stock
DCON
6.3
Order Number
LCF
(mm) (l/d)
Internal Coolant
Dimensions (mm)
DP1020
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
69.5 73.5 128.5 127 1.5
69.5 73.5 128.5 127 1.5 10
95.5 100.5 155.5 154 1.5 9

95.5 100.5 155.5 154 1.5 10
2
2
44.0 46.5 101.5 100 1.5 9

44.0 46.5 101.5 100 1.5 10
2
2
69.5 73.5 128.5 127 1.5
69.5 73.5 128.5 127 1.5 10
95.5 100.5 155.5 154 1.5 9

95.5 100.5 155.5 154 1.5 10
2
2
44.0 46.5 101.5 100 1.5 9

44.0 46.5 101.5 100 1.5 10
2
2
69.5 73.5 128.5 127 1.5
69.5 73.5 128.5 127 1.5 10
95.5 100.5 155.5 154 1.5 9

95.5 100.5 155.5 154 1.5 10
2
2
CARBIDE
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
9.1 5
8
8.5
8.6
8.7
8.8
8.9
9.0
a
a
9.2 5
69.5 73.5 128.5 127 1.5 10
95.5 100.5 155.5 154 1.5 9

95.5 100.5 155.5 154 1.5 10
2
2
9.4 5
44.0 46.5 101.5 100 1.5 9

44.0 46.5 101.5 100 1.5 10
2
2
69.5 73.5 128.5 127 1.5
3
9.5 5
8
69.5 73.5 128.5 127 1.5 10
95.5 100.5 155.5 154 1.5 9

95.5 100.5 155.5 154 1.5 10
2
2
9.6 5
46.6 46.6 101.6 100 1.6 9

46.6 48.6 101.6 100 1.6 10
2
2
3
9.7 5
8
3
9.8 5
8
3
9.9 5
8
73.6 73.6 128.6 127 1.6
73.6 75.6 128.6 127 1.6 10
100.6 100.6 155.6 154 1.6 9

100.6 102.6 155.6 154 1.6 10
2
2
46.6 46.6 101.6 100 1.6 9

46.6 48.6 101.6 100 1.6 10
2
2
73.6 73.6 128.6 127 1.6
a
a
a
a
a
a
73.6 75.6 128.6 127 1.6 10
100.6 100.6 155.6 154 1.6 9

100.6 102.6 155.6 154 1.6 10
2
2
3
10.0 5
8
46.6 46.6 101.6 100 1.6 9

46.6 48.6 101.6 100 1.6 10
2
2
3
3
73.6 73.6 128.6 127 1.6
a
a
73.6 75.6 128.6 127 1.6 10
100.6 100.6 155.6 154 1.6 9

100.6 102.6 155.6 154 1.6 10
2
2
8
8
46.6 46.6 101.6 100 1.6 9

46.6 48.6 101.6 100 1.6 10
2
2
3
3
73.6 73.6 128.6 127 1.6
10.1
73.6 75.6 128.6 127 1.6 10
100.6 100.6 155.6 154 1.6 9

100.6 102.6 155.6 154 1.6 10
2
2
8
8
46.6 46.6 101.6 100 1.6 9

46.6 48.6 101.6 100 1.6 10
2
2
3
3
73.6 73.6 128.6 127 1.6
10.2
10.3
73.6 75.6 128.6 127 1.6 10
100.6 100.6 155.6 154 1.6 9

100.6 102.6 155.6 154 1.6 10
2
2
8
8
49.2 51.7 107.7 106 1.7 10

77.7 81.7 137.7 136 1.7 10
106.7 111.7 167.7 166 1.7 10
2
2
2
3
3
49.2 51.7 107.7 106 1.7 10

77.7 81.7 137.7 136 1.7 10
106.7 111.7 167.7 166 1.7 10
2
2
2
8
8
10.4
DCON
PL
LF
OAL
69.5 73.5 128.5 127 1.5
MVS0930X03S100
MVS0930X05S100
MVS0930X08S100
MVS0940X03S100
MVS0940X05S100
MVS0940X08S100
MVS0950X03S100
MVS0950X05S100
MVS0950X08S100
MVS0960X03S100
MVS0960X05S100
MVS0960X08S100
MVS0970X03S100
MVS0970X05S100
MVS0970X08S100
MVS0980X03S100
MVS0980X05S100
MVS0980X08S100
MVS0990X03S100
MVS0990X05S100
MVS0990X08S100
MVS1000X03S100
MVS1000X05S100
MVS1000X08S100
MVS1010X03S110
MVS1010X03S120
MVS1010X05S110
MVS1010X05S120
MVS1010X08S110
MVS1010X08S120
MVS1020X03S110
MVS1020X03S120
MVS1020X05S110
MVS1020X05S120
MVS1020X08S110
MVS1020X08S120
MVS1030X03S110
MVS1030X03S120
MVS1030X05S110
MVS1030X05S120
MVS1030X08S110
MVS1030X08S120
MVS1040X03S110
MVS1040X03S120
MVS1040X05S110
MVS1040X05S120
MVS1040X08S110
MVS1040X08S120
(mm) (l/d)
LH
DC
LCF
Hole Depth
DCON
9.3 5
PL
2
2
Type
Type
49.2 51.7 107.7 106 1.7 10

77.7 81.7 137.7 136 1.7 10
106.7 111.7 167.7 166 1.7 10
2
2
2
49.2 51.7 107.7 106 1.7 10

77.7 81.7 137.7 136 1.7 10
106.7 111.7 167.7 166 1.7 10
2
2
2
49.2 51.7 107.7 106 1.7 10

77.7 81.7 137.7 136 1.7 10
106.7 111.7 167.7 166 1.7 10
2
2
2
51.7 51.7 107.7 106 1.7 10

81.7 81.7 137.7 136 1.7 10
111.7 111.7 167.7 166 1.7 10
2
2
2
51.8 51.8 107.8 106 1.8 10

81.8 81.8 137.8 136 1.8 10
111.8 111.8 167.8 166 1.8 10
2
2
2
51.8 51.8 107.8 106 1.8 10

81.8 81.8 137.8 136 1.8 10
111.8 111.8 167.8 166 1.8 10
2
2
2
51.8 51.8 107.8 106 1.8 10

81.8 81.8 137.8 136 1.8 10
111.8 111.8 167.8 166 1.8 10
2
2
2
51.8 51.8 107.8 106 1.8 10

81.8 81.8 137.8 136 1.8 10
111.8 111.8 167.8 166 1.8 10
2
2
2
54.3 56.8 117.8 116 1.8 11

54.3 56.8 117.8 116 1.8 12
2
2
85.8 89.8 150.8 149 1.8
11
85.8 89.8 150.8 149 1.8 12
117.8 122.8 183.8 182 1.8 11

117.8 122.8 183.8 182 1.8 12
2
2
54.4 56.9 117.9 116 1.9 11

54.4 56.9 117.9 116 1.9 12
2
2
85.9 89.9 150.9 149 1.9
11
85.9 89.9 150.9 149 1.9 12
117.9 122.9 183.9 182 1.9 11

117.9 122.9 183.9 182 1.9 12
2
2
54.4 56.9 117.9 116 1.9 11

54.4 56.9 117.9 116 1.9 12
2
2
85.9 89.9 150.9 149 1.9
11
85.9 89.9 150.9 149 1.9 12
117.9 122.9 183.9 182 1.9 11

117.9 122.9 183.9 182 1.9 12
2
2
54.4 56.9 117.9 116 1.9 11

54.4 56.9 117.9 116 1.9 12
2
2
85.9 89.9 150.9 149 1.9
11
85.9 89.9 150.9 149 1.9 12
117.9 122.9 183.9 182 1.9 11

117.9 122.9 183.9 182 1.9 12
2
2
CUTTING CONDITIONS
TECHNICAL DATA
N022
Q001
DRILLING
8.4
DP1020
44.0 46.5 101.5 100 1.5 9

44.0 46.5 101.5 100 1.5 10
LF
MVS0840X03S090
MVS0840X03S100
MVS0840X05S090
MVS0840X05S100
MVS0840X08S090
MVS0840X08S100
MVS0850X03S090
MVS0850X03S100
MVS0850X05S090
MVS0850X05S100
MVS0850X08S090
MVS0850X08S100
MVS0860X03S090
MVS0860X03S100
MVS0860X05S090
MVS0860X05S100
MVS0860X08S090
MVS0860X08S100
MVS0870X03S090
MVS0870X03S100
MVS0870X05S090
MVS0870X05S100
MVS0870X08S090
MVS0870X08S100
MVS0880X03S090
MVS0880X03S100
MVS0880X05S090
MVS0880X05S100
MVS0880X08S090
MVS0880X08S100
MVS0890X03S090
MVS0890X03S100
MVS0890X05S090
MVS0890X05S100
MVS0890X08S090
MVS0890X08S100
MVS0900X03S090
MVS0900X03S100
MVS0900X05S090
MVS0900X05S100
MVS0900X08S090
MVS0900X08S100
MVS0910X03S100
MVS0910X05S100
MVS0910X08S100
MVS0920X03S100
MVS0920X05S100
MVS0920X08S100
OAL
3
3
Dimensions (mm)
Stock
Order Number
LH
Order Number
LCF
(mm) (l/d)
Internal Coolant
Dimensions (mm)
DP1020
DC
Hole Depth
Internal Coolant
Stock
N017
MVS
WSTAR DRILLS
10.6
10.7
10.8
10.9
DRILLING
11.0
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
3
3
8
8
a
a
11.2 5
11.3 5
11.4 5
85.9 89.9 150.9 149 1.9 12
117.9 122.9 183.9 182 1.9 11

117.9 122.9 183.9 182 1.9 12
2
2
11.6 5
56.9 56.9 117.9 116 1.9 11

56.9 57.9 117.9 116 1.9 12
2
2
89.9 89.9 150.9 149 1.9
3
11.7 5
8
11
a
a
89.9 90.9 150.9 149 1.9 12
122.9 122.9 183.9 182 1.9 11

122.9 123.9 183.9 182 1.9 12
2
2
11.8 5
56.9 56.9 117.9 116 1.9 11

56.9 57.9 117.9 116 1.9 12
2
2
89.9 89.9 150.9 149 1.9
3
11.9 5
8
11
89.9 90.9 150.9 149 1.9 12
122.9 122.9 183.9 182 1.9 11

122.9 123.9 183.9 182 1.9 12
2
2
3
12.0 5
8
57.0 57.0 118.0 116 2.0 11

57.0 58.0 118.0 116 2.0 12
2
2
3
3
90.0 90.0 151.0 149 2.0
a
a
a
a
2
2
8
8
57.0 57.0 118.0 116 2.0 11

57.0 58.0 118.0 116 2.0 12
2
2
3
3
90.0 90.0 151.0 149 2.0
11
90.0 91.0 151.0 149 2.0 12
123.0 123.0 184.0 182 2.0 11

123.0 124.0 184.0 182 2.0 12
11
90.0 91.0 151.0 149 2.0 12
123.0 123.0 184.0 182 2.0 11

123.0 124.0 184.0 182 2.0 12
12.1
r
a
r
2
2
8
8
57.0 57.0 118.0 116 2.0 11

57.0 58.0 118.0 116 2.0 12
2
2
3
3
90.0 90.0 151.0 149 2.0
11
90.0 91.0 151.0 149 2.0 12
123.0 123.0 184.0 182 2.0 11

123.0 124.0 184.0 182 2.0 12
12.2
r
a
r
2
2
8
8
59.5 62.0 124.0 122 2.0 12

94.0 98.0 160.0 158 2.0 12
129.0 134.0 196.0 194 2.0 12
2
2
2
3
3
59.5 62.0 124.0 122 2.0 12

94.0 98.0 160.0 158 2.0 12
129.0 134.0 196.0 194 2.0 12
2
2
2
59.6 62.1 124.1 122 2.1 12

94.1 98.1 160.1 158 2.1 12
129.1 134.1 196.1 194 2.1 12
2
2
2
59.6 62.1 124.1 122 2.1 12

94.1 98.1 160.1 158 2.1 12
129.1 134.1 196.1 194 2.1 12
2
2
2
12.3
12.4
a
r
8
8
3
3
12.5
r
a
r
8
8
a
r
DCON
PL
11
(mm) (l/d)
LF
85.9 89.9 150.9 149 1.9
MVS1150X03S120
MVS1150X05S120
MVS1150X08S120
MVS1160X03S120
MVS1160X05S120
MVS1160X08S120
MVS1170X03S120
MVS1170X05S120
MVS1170X08S120
MVS1180X03S120
MVS1180X05S120
MVS1180X08S120
MVS1190X03S120
MVS1190X05S120
MVS1190X08S120
MVS1200X03S120
MVS1200X05S120
MVS1200X08S120
MVS1210X03S130
MVS1210X03S140
MVS1210X05S130
MVS1210X05S140
MVS1210X08S130
MVS1210X08S140
MVS1220X03S130
MVS1220X03S140
MVS1220X05S130
MVS1220X05S140
MVS1220X08S130
MVS1220X08S140
MVS1230X03S130
MVS1230X03S140
MVS1230X05S130
MVS1230X05S140
MVS1230X08S130
MVS1230X08S140
MVS1240X03S130
MVS1240X03S140
MVS1240X05S130
MVS1240X05S140
MVS1240X08S130
MVS1240X08S140
MVS1250X03S130
MVS1250X03S140
MVS1250X05S130
MVS1250X05S140
MVS1250X08S130
MVS1250X08S140
DC
OAL
Type
LH
Hole Depth
DCON
11.5 5
PL
2
2
LF
54.4 56.9 117.9 116 1.9 11

54.4 56.9 117.9 116 1.9 12
OAL
Order Number
LH
MVS1050X03S110
MVS1050X03S120
MVS1050X05S110
MVS1050X05S120
MVS1050X08S110
MVS1050X08S120
MVS1060X03S110
MVS1060X03S120
MVS1060X05S110
MVS1060X05S120
MVS1060X08S110
MVS1060X08S120
MVS1070X03S110
MVS1070X03S120
MVS1070X05S110
MVS1070X05S120
MVS1070X08S110
MVS1070X08S120
MVS1080X03S110
MVS1080X03S120
MVS1080X05S110
MVS1080X05S120
MVS1080X08S110
MVS1080X08S120
MVS1090X03S110
MVS1090X03S120
MVS1090X05S110
MVS1090X05S120
MVS1090X08S110
MVS1090X08S120
MVS1100X03S110
MVS1100X03S120
MVS1100X05S110
MVS1100X05S120
MVS1100X08S110
MVS1100X08S120
MVS1110X03S120
MVS1110X05S120
MVS1110X08S120
MVS1120X03S120
MVS1120X05S120
MVS1120X08S120
MVS1130X03S120
MVS1130X05S120
MVS1130X08S120
MVS1140X03S120
MVS1140X05S120
MVS1140X08S120
11.1 5
N018
3
3
Dimensions (mm)
Stock
DP1020
10.5
Order Number
LCF
(mm) (l/d)
Internal Coolant
Dimensions (mm)
DP1020
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
Type
59.6 62.1 124.1 122 2.1 12

94.1 98.1 160.1 158 2.1 12
129.1 134.1 196.1 194 2.1 12
2
2
2
62.1 62.1 124.1 122 2.1 12

98.1 98.1 160.1 158 2.1 12
134.1 134.1 196.1 194 2.1 12
2
2
2
62.1 62.1 124.1 122 2.1 12

98.1 98.1 160.1 158 2.1 12
134.1 134.1 196.1 194 2.1 12
2
2
2
62.1 62.1 124.1 122 2.1 12

98.1 98.1 160.1 158 2.1 12
134.1 134.1 196.1 194 2.1 12
2
2
2
62.2 62.2 124.2 122 2.2 12

98.2 98.2 160.2 158 2.2 12
134.2 134.2 196.2 194 2.2 12
2
2
2
62.2 62.2 124.2 122 2.2 12

98.2 98.2 160.2 158 2.2 12
134.2 134.2 196.2 194 2.2 12
2
2
2
64.7 67.2 130.2 128 2.2 13

64.7 67.2 130.2 128 2.2 14
2
2
102.2 106.2 169.2 167 2.2 13
102.2 106.2 169.2 167 2.2 14
140.2 145.2 208.2 206 2.2 13

140.2 145.2 208.2 206 2.2 14
2
2
64.7 67.2 130.2 128 2.2 13

64.7 67.2 130.2 128 2.2 14
2
2
102.2 106.2 169.2 167 2.2 13
102.2 106.2 169.2 167 2.2 14
140.2 145.2 208.2 206 2.2 13

140.2 145.2 208.2 206 2.2 14
2
2
64.7 67.2 130.2 128 2.2 13

64.7 67.2 130.2 128 2.2 14
2
2
102.2 106.2 169.2 167 2.2 13
102.2 106.2 169.2 167 2.2 14
140.2 145.2 208.2 206 2.2 13

140.2 145.2 208.2 206 2.2 14
2
2
64.8 67.3 130.3 128 2.3 13

64.8 67.3 130.3 128 2.3 14
2
2
102.3 106.3 169.3 167 2.3 13
102.3 106.3 169.3 167 2.3 14
140.3 145.3 208.3 206 2.3 13

140.3 145.3 208.3 206 2.3 14
2
2
64.8 67.3 130.3 128 2.3 13

64.8 67.3 130.3 128 2.3 14
2
2
102.3 106.3 169.3 167 2.3 13
102.3 106.3 169.3 167 2.3 14
140.3 145.3 208.3 206 2.3 13

140.3 145.3 208.3 206 2.3 14
2
2
CARBIDE
12.7
12.8
12.9
3
3
8
8
3
3
a
r
8
8
3
3
8
8
3
3
8
8
3
3
13.0
r
a
r
8
8
a
r
13.1 5
3
13.2 5
8
13.3 5
13.4 5
3
13.5 5
8
a
a
a
13.6 5
MVS1260X03S130
MVS1260X03S140
MVS1260X05S130
MVS1260X05S140
MVS1260X08S130
MVS1260X08S140
MVS1270X03S130
MVS1270X03S140
MVS1270X05S130
MVS1270X05S140
MVS1270X08S130
MVS1270X08S140
MVS1280X03S130
MVS1280X03S140
MVS1280X05S130
MVS1280X05S140
MVS1280X08S130
MVS1280X08S140
MVS1290X03S130
MVS1290X03S140
MVS1290X05S130
MVS1290X05S140
MVS1290X08S130
MVS1290X08S140
MVS1300X03S130
MVS1300X03S140
MVS1300X05S130
MVS1300X05S140
MVS1300X08S130
MVS1300X08S140
MVS1310X03S140
MVS1310X05S140
MVS1310X08S140
MVS1320X03S140
MVS1320X05S140
MVS1320X08S140
MVS1330X03S140
MVS1330X05S140
MVS1330X08S140
MVS1340X03S140
MVS1340X05S140
MVS1340X08S140
MVS1350X03S140
MVS1350X05S140
MVS1350X08S140
MVS1360X03S140
MVS1360X05S140
MVS1360X08S140
2
2
13.7 5
106.3 106.3 169.3 167 2.3 13
106.3 106.3 169.3 167 2.3 14
145.3 145.3 208.3 206 2.3 13

145.3 145.3 208.3 206 2.3 14
2
2
13.8 5
67.3 67.3 130.3 128 2.3 13

67.3 67.3 130.3 128 2.3 14
2
2
106.3 106.3 169.3 167 2.3 13
3
13.9 5
8
106.3 106.3 169.3 167 2.3 14
145.3 145.3 208.3 206 2.3 13

145.3 145.3 208.3 206 2.3 14
2
2
14.0 5
67.3 67.3 130.3 128 2.3 13

67.3 67.3 130.3 128 2.3 14
2
2
3
3
106.3 106.3 169.3 167 2.3 13
106.3 106.3 169.3 167 2.3 14
145.3 145.3 208.3 206 2.3 13

145.3 145.3 208.3 206 2.3 14
2
2
8
8
67.3 67.3 130.3 128 2.3 13

67.3 67.3 130.3 128 2.3 14
2
2
3
3
106.3 106.3 169.3 167 2.3 13
106.3 106.3 169.3 167 2.3 14
145.3 145.3 208.3 206 2.3 13

145.3 145.3 208.3 206 2.3 14
14.1
2
2
8
8
a
r
67.4 67.4 130.4 128 2.4 13

67.4 67.4 130.4 128 2.4 14
2
2
3
3
106.4 106.4 169.4 167 2.4 13
106.4 106.4 169.4 167 2.4 14
145.4 145.4 208.4 206 2.4 13

145.4 145.4 208.4 206 2.4 14
14.2
2
2
8
8
69.9 72.4 136.4 134 2.4 14

110.4 114.4 178.4 176 2.4 14
151.4 156.4 220.4 218 2.4 14
2
2
2
3
3
69.9 72.4 136.4 134 2.4 14

110.4 114.4 178.4 176 2.4 14
151.4 156.4 220.4 218 2.4 14
2
2
2
69.9 72.4 136.4 134 2.4 14

110.4 114.4 178.4 176 2.4 14
151.4 156.4 220.4 218 2.4 14
2
2
2
69.9 72.4 136.4 134 2.4 14

110.4 114.4 178.4 176 2.4 14
151.4 156.4 220.4 218 2.4 14
2
2
2
70.0 72.5 136.5 134 2.5 14

110.5 114.5 178.5 176 2.5 14
151.5 156.5 220.5 218 2.5 14
2
2
2
72.5 72.5 136.5 134 2.5 14

114.5 114.5 178.5 176 2.5 14
156.5 156.5 220.5 218 2.5 14
2
2
2
14.3
14.4
14.6
a
r
8
8
3
3
14.5
r
a
r
8
8
a
r
3
3
8
8
r
r
MVS1370X03S140
MVS1370X05S140
MVS1370X08S140
MVS1380X03S140
MVS1380X05S140
MVS1380X08S140
MVS1390X03S140
MVS1390X05S140
MVS1390X08S140
MVS1400X03S140
MVS1400X05S140
MVS1400X08S140
MVS1410X03S150
MVS1410X03S160
MVS1410X05S150
MVS1410X05S160
MVS1410X08S150
MVS1410X08S160
MVS1420X03S150
MVS1420X03S160
MVS1420X05S150
MVS1420X05S160
MVS1420X08S150
MVS1420X08S160
MVS1430X03S150
MVS1430X03S160
MVS1430X05S150
MVS1430X05S160
MVS1430X08S150
MVS1430X08S160
MVS1440X03S150
MVS1440X03S160
MVS1440X05S150
MVS1440X05S160
MVS1440X08S150
MVS1440X08S160
MVS1450X03S150
MVS1450X03S160
MVS1450X05S150
MVS1450X05S160
MVS1450X08S150
MVS1450X08S160
MVS1460X03S150
MVS1460X03S160
MVS1460X05S150
MVS1460X05S160
MVS1460X08S150
MVS1460X08S160
DCON
PL
LF
OAL
LH
(mm) (l/d)
67.3 67.3 130.3 128 2.3 13

67.3 67.3 130.3 128 2.3 14
Order Number
LCF
DC
DP1020
Type
Hole Depth
DCON
PL
LF
OAL
LH
Order Number
Dimensions (mm)
Stock
Type
72.5 72.5 136.5 134 2.5 14

114.5 114.5 178.5 176 2.5 14
156.5 156.5 220.5 218 2.5 14
2
2
2
72.5 72.5 136.5 134 2.5 14 22

114.5 114.5 178.5 176 2.5 14 2
156.5 156.5 220.5 218 2.5 14 2
72.5 72.5 136.5 134 2.5 14
114.5 114.5 178.5 176 2.5 14
156.5 156.5 220.5 218 2.5 14
2
2
2
72.5 72.5 136.5 134 2.5 14

114.5 114.5 178.5 176 2.5 14
156.5 156.5 220.5 218 2.5 14
2
2
2
75.1 77.6 142.6 140 2.6 15

75.1 77.6 142.6 140 2.6 16
2
2
118.6 122.6 187.6 185 2.6 15
118.6 122.6 187.6 185 2.6 16
162.6 167.6 227.6 225 2.6 15

162.6 167.6 227.6 225 2.6 16
2
2
75.1 77.6 142.6 140 2.6 15

75.1 77.6 142.6 140 2.6 16
2
2
118.6 122.6 187.6 185 2.6 15
118.6 122.6 187.6 185 2.6 16
162.6 167.6 227.6 225 2.6 15

162.6 167.6 227.6 225 2.6 16
2
2
75.1 77.6 142.6 140 2.6 15

75.1 77.6 142.6 140 2.6 16
2
2
118.6 122.6 187.6 185 2.6 15
118.6 122.6 187.6 185 2.6 16
162.6 167.6 227.6 225 2.6 15

162.6 167.6 227.6 225 2.6 16
2
2
75.1 77.6 142.6 140 2.6 15

75.1 77.6 142.6 140 2.6 16
2
2
118.6 122.6 187.6 185 2.6 15
118.6 122.6 187.6 185 2.6 16
162.6 167.6 227.6 225 2.6 15

162.6 167.6 227.6 225 2.6 16
2
2
75.1 77.6 142.6 140 2.6 15

75.1 77.6 142.6 140 2.6 16
2
2
118.6 122.6 187.6 185 2.6 15
118.6 122.6 187.6 185 2.6 16
162.6 167.6 227.6 225 2.6 15

162.6 167.6 227.6 225 2.6 16
2
2
77.7 77.7 142.7 140 2.7 15

77.7 77.7 142.7 140 2.7 16
2
2
122.7 122.7 187.7 185 2.7 15
122.7 122.7 187.7 185 2.7 16
167.7 167.7 227.7 225 2.7 15

167.7 167.7 227.7 225 2.7 16
2
2
CUTTING CONDITIONS
TECHNICAL DATA
N022
Q001
DRILLING
12.6
Internal Coolant
Dimensions (mm)
LCF
(mm) (l/d)
DP1020
DC
Hole Depth
Internal Coolant
Stock
N019
MVS
WSTAR DRILLS
14.7
14.8
14.9
15.0
3
3
8
8
3
3
a
r
8
8
3
3
DRILLING
r
a
8
8
3
3
a
r
8
8
a
a
r
3
15.2 5
8
a
a
15.3 5
3
15.4 5
8
a
a
r
3
15.5 5
8
a
a
a
15.6 5
15.7 5
15.8 5
N020
3
15.1 5
8
MVS1470X03S150
MVS1470X03S160
MVS1470X05S150
MVS1470X05S160
MVS1470X08S150
MVS1470X08S160
MVS1480X03S150
MVS1480X03S160
MVS1480X05S150
MVS1480X05S160
MVS1480X08S150
MVS1480X08S160
MVS1490X03S150
MVS1490X03S160
MVS1490X05S150
MVS1490X05S160
MVS1490X08S150
MVS1490X08S160
MVS1500X03S150
MVS1500X03S160
MVS1500X05S150
MVS1500X05S160
MVS1500X08S150
MVS1500X08S160
MVS1510X03S160
MVS1510X05S160
MVS1510X08S160
MVS1520X03S160
MVS1520X05S160
MVS1520X08S160
MVS1530X03S160
MVS1530X05S160
MVS1530X08S160
MVS1540X03S160
MVS1540X05S160
MVS1540X08S160
MVS1550X03S160
MVS1550X05S160
MVS1550X08S160
MVS1560X03S160
MVS1560X05S160
MVS1560X08S160
MVS1570X03S160
MVS1570X05S160
MVS1570X08S160
MVS1580X03S160
MVS1580X05S160
MVS1580X08S160
2
2
15.9 5
122.7 122.7 187.7 185 2.7 15
122.7 122.7 187.7 185 2.7 16
167.7 167.7 227.7 225 2.7 15

167.7 167.7 227.7 225 2.7 16
2
2
16.0 5
77.7 77.7 142.7 140 2.7 15

77.7 77.7 142.7 140 2.7 16
2
2
3
3
122.7 122.7 187.7 185 2.7 15
122.7 122.7 187.7 185 2.7 16
5
5
167.7 167.7 227.7 225 2.7 15

167.7 167.7 227.7 225 2.7 16
2
2
3
3
77.7 77.7 142.7 140 2.7 15

77.7 77.7 142.7 140 2.7 16
2
2
5
5
122.7 122.7 187.7 185 2.7 15
2
2
3
3
122.7 122.7 187.7 185 2.7 16

167.7 167.7 227.7 225 2.7 15
167.7 167.7 227.7 225 2.7 16
2
2
5
5
77.7 77.7 142.7 140 2.7 15

77.7 77.7 142.7 140 2.7 16
2
2
3
3
122.7 122.7 187.7 185 2.7 15
2
2
5
5
122.7 122.7 187.7 185 2.7 16

167.7 167.7 227.7 225 2.7 15
167.7 167.7 227.7 225 2.7 16
2
2
3
3
80.2 82.7 147.7 145 2.7 16

126.7 130.7 195.7 193 2.7 16
173.7 183.7 243.7 241 2.7 16
2
2
2
80.3 82.8 147.8 145 2.8 16

126.8 130.8 195.8 193 2.8 16
173.8 183.8 243.8 241 2.8 16
2
2
2
80.3 82.8 147.8 145 2.8 16

126.8 130.8 195.8 193 2.8 16
173.8 183.8 243.8 241 2.8 16
2
2
2
80.3 82.8 147.8 145 2.8 16

126.8 130.8 195.8 193 2.8 16
173.8 183.8 243.8 241 2.8 16
2
2
2
80.3 82.8 147.8 145 2.8 16

126.8 130.8 195.8 193 2.8 16
173.8 183.8 243.8 241 2.8 16
2
2
2
82.8 82.8 147.8 145 2.8 16

130.8 130.8 195.8 193 2.8 16
178.8 183.8 243.8 241 2.8 16
2
2
2
82.9 82.9 147.9 145 2.9 16

130.9 130.9 195.9 193 2.9 16
178.9 183.9 243.9 241 2.9 16
2
2
2
82.9 82.9 147.9 145 2.9 16

130.9 130.9 195.9 193 2.9 16
178.9 183.9 243.9 241 2.9 16
2
2
2
16.1
16.2
16.3
16.4
16.5
16.6
16.7
16.8
16.9
17.0
17.1
5
5
r
a
r
a
r
3
3
5
5
3
3
5
5
3
3
5
5
3
3
5
5
3
3
5
5
3
5
r
r
MVS1590X03S160
MVS1590X05S160
MVS1590X08S160
MVS1600X03S160
MVS1600X05S160
MVS1600X08S160
MVS1610X03S170
MVS1610X03S180
MVS1610X05S170
MVS1610X05S180
MVS1620X03S170
MVS1620X03S180
MVS1620X05S170
MVS1620X05S180
MVS1630X03S170
MVS1630X03S180
MVS1630X05S170
MVS1630X05S180
MVS1640X03S170
MVS1640X03S180
MVS1640X05S170
MVS1640X05S180
MVS1650X03S170
MVS1650X03S180
MVS1650X05S170
MVS1650X05S180
MVS1660X03S170
MVS1660X03S180
MVS1660X05S170
MVS1660X05S180
MVS1670X03S170
MVS1670X03S180
MVS1670X05S170
MVS1670X05S180
MVS1680X03S170
MVS1680X03S180
MVS1680X05S170
MVS1680X05S180
MVS1690X03S170
MVS1690X03S180
MVS1690X05S170
MVS1690X05S180
MVS1700X03S170
MVS1700X03S180
MVS1700X05S170
MVS1700X05S180
MVS1710X03S180
MVS1710X05S180
DCON
PL
LF
(mm) (l/d)
77.7 77.7 142.7 140 2.7 15

77.7 77.7 142.7 140 2.7 16
Order Number
OAL
DC
LH
Type
Dimensions (mm)
Stock
DP1020
DCON
PL
LF
OAL
LH
Order Number
Hole Depth
Internal Coolant
Dimensions (mm)
LCF
(mm) (l/d)
DP1020
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
Type
82.9 82.9 147.9 145 2.9 16

130.9 130.9 195.9 193 2.9 16
178.9 183.9 243.9 241 2.9 16
2
2
2
82.9 82.9 147.9 145 2.9 16

130.9 130.9 195.9 193 2.9 16
178.9 183.9 243.9 241 2.9 16
2
2
2
85.4 87.9 152.9 150 2.9 17

85.4 87.9 152.9 150 2.9 18
2
2
134.9 138.9 203.9 201 2.9 17

134.9 138.9 203.9 201 2.9 18
2
2
85.4 87.9 152.9 150 2.9 17

85.4 87.9 152.9 150 2.9 18
2
2
134.9 138.9 203.9 201 2.9 17

134.9 138.9 203.9 201 2.9 18
2
2
85.5 88.0 153.0 150 3.0 17

85.5 88.0 153.0 150 3.0 18
2
2
135.0 139.0 204.0 201 3.0 17

135.0 139.0 204.0 201 3.0 18
2
2
85.5 88.0 153.0 150 3.0 17

85.5 88.0 153.0 150 3.0 18
2
2
135.0 139.0 204.0 201 3.0 17

135.0 139.0 204.0 201 3.0 18
2
2
85.5 88.0 153.0 150 3.0 17

85.5 88.0 153.0 150 3.0 18
2
2
135.0 139.0 204.0 201 3.0 17

135.0 139.0 204.0 201 3.0 18
2
2
88.0 88.0 153.0 150 3.0 17

88.0 88.0 153.0 150 3.0 18
2
2
139.0 139.0 204.0 201 3.0 17

139.0 139.0 204.0 201 3.0 18
2
2
88.0 88.0 153.0 150 3.0 17

88.0 88.0 153.0 150 3.0 18
2
2
139.0 139.0 204.0 201 3.0 17

139.0 139.0 204.0 201 3.0 18
2
2
88.1 88.1 153.1 150 3.1 17

88.1 88.1 153.1 150 3.1 18
2
2
139.1 139.1 204.1 201 3.1 17

139.1 139.1 204.1 201 3.1 18
2
2
88.1 88.1 153.1 150 3.1 17

88.1 88.1 153.1 150 3.1 18
2
2
139.1 139.1 204.1 201 3.1 17

139.1 139.1 204.1 201 3.1 18
2
2
88.1 88.1 153.1 150 3.1 17

88.1 88.1 153.1 150 3.1 18
2
2
139.1 139.1 204.1 201 3.1 17

139.1 139.1 204.1 201 3.1 18
2
2
90.6 93.1 158.1 155 3.1 18

143.1 147.1 212.1 209 3.1 18
2
2
CARBIDE
17.3
3
5
17.4
3
5
17.5
3
5
17.6
3
5
3
17.7
5
17.8
3
5
17.9
3
5
18.0
3
5
3
3
5
5
3
3
5
5
3
3
5
5
3
3
5
5
3
3
a
r
5
5
18.2
18.3
18.4
18.5
18.6
18.7
3
3
5
5
3
3
5
5
MVS1720X03S180
MVS1720X05S180
MVS1730X03S180
MVS1730X05S180
MVS1740X03S180
MVS1740X05S180
MVS1750X03S180
MVS1750X05S180
MVS1760X03S180
MVS1760X05S180
MVS1770X03S180
MVS1770X05S180
MVS1780X03S180
MVS1780X05S180
MVS1790X03S180
MVS1790X05S180
MVS1800X03S180
MVS1800X05S180
MVS1810X03S190
MVS1810X03S200
MVS1810X05S190
MVS1810X05S200
MVS1820X03S190
MVS1820X03S200
MVS1820X05S190
MVS1820X05S200
MVS1830X03S190
MVS1830X03S200
MVS1830X05S190
MVS1830X05S200
MVS1840X03S190
MVS1840X03S200
MVS1840X05S190
MVS1840X05S200
MVS1850X03S190
MVS1850X03S200
MVS1850X05S190
MVS1850X05S200
MVS1860X03S190
MVS1860X03S200
MVS1860X05S190
MVS1860X05S200
MVS1870X03S190
MVS1870X03S200
MVS1870X05S190
MVS1870X05S200
2
2
90.6 93.1 158.1 155 3.1 18

143.1 147.1 212.1 209 3.1 18
2
2
90.7 93.2 158.2 155 3.2 18

143.2 147.2 212.2 209 3.2 18
2
2
90.7 93.2 158.2 155 3.2 18

143.2 147.2 212.2 209 3.2 18
2
2
93.2 93.2 158.2 155 3.2 18

147.2 147.2 212.2 209 3.2 18
2
2
93.2 93.2 158.2 155 3.2 18

147.2 147.2 212.2 209 3.2 18
2
2
93.2 93.2 158.2 155 3.2 18

147.2 147.2 212.2 209 3.2 18
2
2
19.1
3
5
93.3 93.3 158.3 155 3.3 18

147.3 147.3 212.3 209 3.3 18
2
2
19.2
3
5
93.3 93.3 158.3 155 3.3 18

147.3 147.3 212.3 209 3.3 18
2
2
19.3
3
5
95.8 98.3 163.3 160 3.3 19

95.8 98.3 163.3 160 3.3 20
2
2
19.4
3
5
151.3 155.3 220.3 217 3.3 19

151.3 155.3 220.3 217 3.3 20
2
2
19.5
3
5
95.8 98.3 163.3 160 3.3 19

95.8 98.3 163.3 160 3.3 20
2
2
19.6
3
5
151.3 155.3 220.3 217 3.3 19

151.3 155.3 220.3 217 3.3 20
2
2
19.7
3
5
95.8 98.3 163.3 160 3.3 19

95.8 98.3 163.3 160 3.3 20
2
2
19.8
3
5
151.3 155.3 220.3 217 3.3 19

151.3 155.3 220.3 217 3.3 20
2
2
19.9
3
5
95.8 98.3 163.3 160 3.3 19

95.8 98.3 163.3 160 3.3 20
2
2
20.0
3
5
151.3 155.3 220.3 217 3.3 19

151.3 155.3 220.3 217 3.3 20
2
2
95.9 98.4 163.4 160 3.4 19

95.9 98.4 163.4 160 3.4 20
2
2
151.4 155.4 220.4 217 3.4 19

151.4 155.4 220.4 217 3.4 20
2
2
98.4 98.4 163.4 160 3.4 19

98.4 98.4 163.4 160 3.4 20
2
2
155.4 155.4 220.4 217 3.4 19

155.4 155.4 220.4 217 3.4 20
2
2
98.4 98.4 163.4 160 3.4 19

98.4 98.4 163.4 160 3.4 20
2
2
155.4 155.4 220.4 217 3.4 19

155.4 155.4 220.4 217 3.4 20
2
2
18.8
18.9
19.0
3
3
5
5
3
3
5
5
3
3
5
5
MVS1880X03S190
MVS1880X03S200
MVS1880X05S190
MVS1880X05S200
MVS1890X03S190
MVS1890X03S200
MVS1890X05S190
MVS1890X05S200
MVS1900X03S190
MVS1900X03S200
MVS1900X05S190
MVS1900X05S200
MVS1910X03S200
MVS1910X05S200
MVS1920X03S200
MVS1920X05S200
MVS1930X03S200
MVS1930X05S200
MVS1940X03S200
MVS1940X05S200
MVS1950X03S200
MVS1950X05S200
MVS1960X03S200
MVS1960X05S200
MVS1970X03S200
MVS1970X05S200
MVS1980X03S200
MVS1980X05S200
MVS1990X03S200
MVS1990X05S200
MVS2000X03S200
MVS2000X05S200
DCON
PL
LF
OAL
LH
(mm) (l/d)
90.6 93.1 158.1 155 3.1 18

143.1 147.1 212.1 209 3.1 18
Order Number
LCF
DC
DP1020
Type
Hole Depth
DCON
PL
LF
OAL
LH
Order Number
Dimensions (mm)
Stock
Type
98.4 98.4 163.4 160 3.4 19

98.4 98.4 163.4 160 3.4 20
2
2
155.4 155.4 220.4 217 3.4 19

155.4 155.4 220.4 217 3.4 20
2
2
98.4 98.4 163.4 160 3.4 19

98.4 98.4 163.4 160 3.4 20
2
2
155.4 155.4 220.4 217 3.4 19

155.4 155.4 220.4 217 3.4 20
2
2
98.5 98.5 163.5 160 3.5 19

98.5 98.5 163.5 160 3.5 20
2
2
155.5 155.5 220.5 217 3.5 19

155.5 155.5 220.5 217 3.5 20
2
2
101.0 103.5 168.5 165 3.5 20

159.5 163.5 228.5 225 3.5 20
2
2
101.0 103.5 168.5 165 3.5 20

159.5 163.5 228.5 225 3.5 20
2
2
101.0 103.5 168.5 165 3.5 20

159.5 163.5 228.5 225 3.5 20
2
2
101.0 103.5 168.5 165 3.5 20

159.5 163.5 228.5 225 3.5 20
2
2
101.0 103.5 168.5 165 3.5 20

159.5 163.5 228.5 225 3.5 20
2
2
103.6 103.6 168.6 165 3.6 20

163.6 163.6 228.6 225 3.6 20
2
2
103.6 103.6 168.6 165 3.6 20

163.6 163.6 228.6 225 3.6 20
2
2
103.6 103.6 168.6 165 3.6 20

163.6 163.6 228.6 225 3.6 20
2
2
103.6 103.6 168.6 165 3.6 20

163.6 163.6 228.6 225 3.6 20
2
2
103.6 103.6 168.6 165 3.6 20

163.6 163.6 228.6 225 3.6 20
2
2
DRILLING
3
17.2
5
18.1
Internal Coolant
Dimensions (mm)
LCF
(mm) (l/d)
DP1020
DC
Hole Depth
Internal Coolant
Stock
CUTTING CONDITIONS
TECHNICAL DATA
N022
Q001
N021
CARBIDE
MVS
WSTAR DRILLS
Work
Material
Dia.
DC
(mm)
1.0
1.5
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
1.0
1.5
2.0
DRILLING
2.5
N022
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
Carbon steel, Alloy steel (180 280HB) Carbon steel, Alloy steel (280 350HB)
AISI 1010 etc
AISI 1045, AISI 4140 etc
L/D
Revolution
(min-1)
S*,7DC
12D
S*,7DC
12D
S*,7DC
12D
S*,7DC
12D
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
15900
15900
10600
10600
7900
7900
7600
7600
8900
7900
6300
5500
4700
4100
3700
3100
2500
Work
Material
Dia.
DC
(mm)
Mild Steel ( < 180HB)
0.04
0.02
0.05
0.05
0.07
0.07
0.09
0.09
0.1
0.12
0.15
0.2
0.23
0.27
0.3
0.33
0.35
(0.02 0.05)
(0.01 0.03)
(0.03 0.08)
(0.02 0.08)
(0.04 0.10)
(0.04 0.10)
(0.05 0.13)
(0.06 0.13)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.26 0.34)
(0.27 0.38)
(0.30 0.40)
Revolution
(min-1)
15900
12700
10600
8400
7900
7900
7600
6300
7900
7100
5700
5000
4300
3800
3400
2700
2200
Feed rate
(Min. Max.)
(mm/rev)
0.04
0.02
0.05
0.05
0.07
0.07
0.09
0.09
0.1
0.12
0.15
0.2
0.23
0.27
0.3
0.33
0.35
(0.02 0.05)
(0.01 0.03)
(0.03 0.08)
(0.03 0.08)
(0.04 0.10)
(0.04 0.10)
(0.05 0.13)
(0.06 0.13)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.26 0.34)
(0.27 0.38)
(0.30 0.40)
Revolution
(min-1)
12700
9500
8400
6300
6300
7900
6300
6300
6900
6300
5000
4500
3900
3500
3100
2500
2000
Feed rate
(Min. Max.)
(mm/rev)
0.04
0.02
0.05
0.05
0.07
0.07
0.09
0.08
0.1
0.11
0.14
0.18
0.21
0.23
0.26
0.28
0.3
(0.02 0.05)
(0.01 0.03)
(0.03 0.08)
(0.02 0.08)
(0.04 0.10)
(0.04 0.10)
(0.05 0.13)
(0.05 0.13)
(0.06 0.13)
(0.07 0.14)
(0.09 0.18)
(0.11 0.24)
(0.16 0.25)
(0.19 0.27)
(0.22 0.29)
(0.23 0.33)
(0.26 0.34)
Austenitic Stainless Steel ( < 200HB)
Gray Cast Iron ( < 350MPa)
Ductile Cast Iron ( < 450MPa)
No 45 B etc
60-40-8 etc
L/D
Revolution
(min-1)
S*,7DC
12D
S*,7DC
12D
S*,7DC
12D
S*,7DC
12D
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
9500
9500
6300
6300
4700
4700
5000
3800
3900
3100
2500
2500
1900
1500
1500
1100
900
S*=2DC for cutting a guide hole
Feed rate
(Min. Max.)
(mm/rev)
AISI 4340 etc
Feed rate
(Min. Max.)
(mm/rev)
0.03
0.02
0.05
0.05
0.06
0.07
0.08
0.08
0.08
0.09
0.11
0.14
0.15
0.16
0.18
0.19
0.21
(0.02 0.05)
(0.01 0.03)
(0.03 0.07)
(0.02 0.08)
(0.04 0.08)
(0.04 0.10)
(0.05 0.10)
(0.05 0.12)
(0.06 0.10)
(0.06 0.11)
(0.08 0.14)
(0.09 0.18)
(0.10 0.19)
(0.12 0.20)
(0.15 0.21)
(0.14 0.24)
(0.15 0.26)
Revolution
(min-1)
15900
12700
10600
8400
7900
7900
7600
6300
8900
7900
6300
5500
4700
4100
3700
3100
2500
Feed rate
(Min. Max.)
(mm/rev)
0.04
0.02
0.05
0.05
0.07
0.07
0.09
0.09
0.1
0.12
0.15
0.2
0.25
0.29
0.32
0.35
0.37
(0.02 0.05)
(0.01 0.03)
(0.03 0.08)
(0.03 0.08)
(0.04 0.10)
(0.04 0.10)
(0.05 0.13)
(0.06 0.13)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.31)
(0.22 0.35)
(0.26 0.37)
(0.28 0.42)
(0.30 0.44)
Revolution
(min-1)
12700
9500
8400
6300
6300
7900
6300
6300
6400
5100
4100
3500
2700
2200
2300
1700
1500
Feed rate
(Min. Max.)
(mm/rev)
0.04
0.02
0.05
0.05
0.07
0.07
0.09
0.08
0.1
0.12
0.15
0.2
0.23
0.27
0.3
0.33
0.35
(0.02 0.05)
(0.01 0.03)
(0.03 0.08)
(0.02 0.08)
(0.04 0.10)
(0.04 0.10)
(0.05 0.13)
(0.05 0.12)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.26 0.34)
(0.28 0.38)
(0.30 0.40)
CARBIDE
Aluminium Alloy (Si<5%)

Work
Material
Dia.
DC
(mm)
1.0
1.5
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
Inconel718 etc
L/D
Revolution
(min-1)
S*,7DC
12DC
S*,7DC
12DC
S*,7DC
12DC
S*,7DC
12DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
3DC,5DC,8DC
19000
15900
16900
14800
14300
12700
12700
11400
11900
9500
7600
7500
5900
4700
4200
3100
2700
Feed rate
(Min. Max.)
(mm/rev)
0.05
0.05
0.07
0.08
0.1
0.11
0.13
0.14
0.23
0.24
0.25
0.35
0.35
0.5
0.5
0.6
0.6
(0.03 0.08)
(0.03 0.08)
(0.05 0.12)
(0.05 0.12)
(0.06 0.15)
(0.06 0.15)
(0.08 0.20)
(0.08 0.20)
(0.10 0.35)
(0.12 0.35)
(0.15 0.35)
(0.20 0.50)
(0.20 0.50)
(0.20 0.80)
(0.20 0.80)
(0.20 1.00)
(0.20 1.00)
Revolution
(min-1)
3100
3100
2100
2100
2300
2300
1900
1900
1900
1500
1200
1200
900
700
600
400
400
Feed rate
(Min. Max.)
(mm/rev)
0.02
0.02
0.03
0.03
0.04
0.04
0.05
0.05
0.07
0.09
0.11
0.13
0.14
0.15
0.16
0.18
0.19
(0.01 0.03)
(0.01 0.03)
(0.02 0.04)
(0.02 0.04)
(0.03 0.05)
(0.03 0.05)
(0.04 0.06)
(0.04 0.06)
(0.05 0.09)
(0.06 0.11)
(0.08 0.14)
(0.09 0.16)
(0.11 0.17)
(0.12 0.17)
(0.13 0.18)
(0.14 0.21)
(0.15 0.22)
DRILLING
S*=2DC for cutting a guide hole
TECHNICAL DATA
Q001
N023
Steel
DC=3
0
0.014
0
0.006
h6
3<DC < 6 6<DC < 10 10<DC < 1818<DC < 20

0
0.018
0
0.008
0
0.027
0
0.011
0
0.033
0
0.013
LF
Type1
Type2
140
DC(h8)
PL
0
0.022
0
0.009
DCON(h6)
MVE
WSTAR DRILLS
a New grade DP1020 offers long tool life for a wide range of work materials.
a The unique wavy cutting edge provides excellent sharpness and rigidity and helps to control wear at the periphery.
DCON(h6)
CARBIDE
LCF
LH
OAL
LF
140
DC(h8)
PL
LCF
LH
OAL
3
3
2
2
3.3
3
3
2
2
3.4
3
3
2
2
DRILLING
3.5
3
3
2
2
3.6
3
3
2
2
3.7
3
3
2
2
3.8
3
3
3.9
2
2
N024
2
1
18.6 20.6 55.6 55

18.6 21.7 55.6 55
0.6
0.6
4
6
2
1
24.6 26.6 60.6 60

24.6 27.7 60.6 60
0.6
0.6
4
6
2
1
18.6 20.6 55.6 55

18.6 21.6 55.6 55
0.6
0.6
4
6
2
1
24.6 26.6 60.6 60

24.6 27.6 60.6 60
0.6
0.6
4
6
2
1
18.6 20.6 55.6 55

18.6 21.5 55.6 55
0.6
0.6
4
6
2
1
24.6 26.6 60.6 60

24.6 27.5 60.6 60
0.6
0.6
4
6
2
1
18.6 20.6 55.6 55

18.6 21.4 55.6 55
0.6
0.6
4
6
2
1
24.6 26.6 60.6 60

24.6 27.4 60.6 60
0.6
0.6
4
6
2
1
18.6 20.6 55.6 55

18.6 21.3 55.6 55
0.6
0.6
4
6
2
1
24.6 26.6 60.6 60

24.6 27.3 60.6 60
0.6
0.6
4
6
2
1
20.7 20.7 55.7 55

20.7 23.3 55.7 55
0.7
0.7
4
6
2
1
27.7 27.7 60.7 60

27.7 30.3 60.7 60
0.7
0.7
4
6
2
1
20.7 20.7 55.7 55

20.7 23.2 55.7 55
0.7
0.7
4
6
2
1
27.7 27.7 60.7 60

27.7 30.2 60.7 60
0.7
0.7
4
6
2
1
20.7 20.7 55.7 55

20.7 23.1 55.7 55
0.7
0.7
4
6
2
1
27.7 27.7 60.7 60

27.7 30.1 60.7 60
0.7
0.7
4
6
2
1
20.7 20.7 55.7 55

20.7 23.0 55.7 55
0.7
0.7
4
6
2
1
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
MVE0390X03S040
MVE0390X03S060
MVE0400X02S040
MVE0400X02S060
MVE0400X03S040
MVE0400X03S060
MVE0410X02S050
MVE0410X02S060
MVE0410X03S050
MVE0410X03S060
MVE0420X02S050
MVE0420X02S060
MVE0420X03S050
MVE0420X03S060
MVE0430X02S050
MVE0430X02S060
MVE0430X03S050
MVE0430X03S060
MVE0440X02S050
MVE0440X02S060
MVE0440X03S050
MVE0440X03S060
MVE0450X02S050
MVE0450X02S060
MVE0450X03S050
MVE0450X03S060
MVE0460X02S050
MVE0460X02S060
MVE0460X03S050
MVE0460X03S060
MVE0470X02S050
MVE0470X02S060
MVE0470X03S050
MVE0470X03S060
MVE0480X02S050
MVE0480X02S060
MVE0480X03S050
MVE0480X03S060
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
DCON
3.2
3
6
PL
0.5
0.5
3
3
27.7 27.7 60.7 60

27.7 30.0 60.7 60
0.7
0.7
4
6
2
1
20.7 20.7 55.7 55

20.7 22.8 55.7 55
0.7
0.7
4
6
2
1
27.7 27.7 60.7 60

27.7 29.8 60.7 60
0.7
0.7
4
6
2
1
22.7 24.7 62.7 62

22.7 24.7 62.7 62
0.7
0.7
5
6
2
1
29.7 31.7 68.7 68

29.7 31.7 68.7 68
0.7
0.7
5
6
2
1
22.8 24.8 62.8 62

22.8 24.7 62.8 62
0.8
0.8
5
6
2
1
29.8 31.8 68.8 68

29.8 31.7 68.8 68
0.8
0.8
5
6
2
1
22.8 24.8 62.8 62

22.8 24.6 62.8 62
0.8
0.8
5
6
2
1
29.8 31.8 68.8 68

29.8 31.6 68.8 68
0.8
0.8
5
6
2
1
22.8 24.8 62.8 62

22.8 24.5 62.8 62
0.8
0.8
5
6
2
1
29.8 31.8 68.8 68

29.8 31.5 68.8 68
0.8
0.8
5
6
2
1
22.8 24.8 62.8 62

22.8 24.4 62.8 62
0.8
0.8
5
6
2
1
29.8 31.8 68.8 68

29.8 31.4 68.8 68
0.8
0.8
5
6
2
1
24.8 24.8 62.8 62

24.8 27.8 62.8 62
0.8
0.8
5
6
2
2
32.8 32.8 68.8 68

32.8 35.8 68.8 68
0.8
0.8
5
6
2
2
24.9 24.9 62.9 62

24.9 27.9 62.9 62
0.9
0.9
5
6
2
2
32.9 32.9 68.9 68

32.9 35.9 68.9 68
0.9
0.9
5
6
2
2
24.9 24.9 62.9 62

24.9 27.9 62.9 62
0.9
0.9
5
6
2
2
32.9 32.9 68.9 68

32.9 35.9 68.9 68
0.9
0.9
5
6
2
2
OAL
2
2
21.5 21.5 60.5 60

21.5 24.7 60.5 60
3.9
LH
(mm) (l/d)
Type
LCF
3
3
Order Number
LF
3.1
0.5
Dimensions (mm)
Stock
DP1020
0.5
16.5 19.7 55.5 55
DC
Hole Depth
2
2
DCON
16.5 16.5 55.5 55
LF
3
3
MVE0300X02S030
MVE0300X02S060
MVE0300X03S030
MVE0300X03S060
MVE0310X02S040
MVE0310X02S060
MVE0310X03S040
MVE0310X03S060
MVE0320X02S040
MVE0320X02S060
MVE0320X03S040
MVE0320X03S060
MVE0330X02S040
MVE0330X02S060
MVE0330X03S040
MVE0330X03S060
MVE0340X02S040
MVE0340X02S060
MVE0340X03S040
MVE0340X03S060
MVE0350X02S040
MVE0350X02S060
MVE0350X03S040
MVE0350X03S060
MVE0360X02S040
MVE0360X02S060
MVE0360X03S040
MVE0360X03S060
MVE0370X02S040
MVE0370X02S060
MVE0370X03S040
MVE0370X03S060
MVE0380X02S040
MVE0380X02S060
MVE0380X03S040
MVE0380X03S060
MVE0390X02S040
MVE0390X02S060
OAL
LH
LCF
Type
PL
3.0
Dimensions (mm)
Order Number
(mm) (l/d)
External Coolant
Stock
DP1020
DC
Hole Depth
External Coolant
CARBIDE
5.5
2
3
5.6
2
3
5.7
2
3
5.8
2
3
5.9
2
3
6.0
2
3
2
2
6.1
3
3
2
2
6.2
3
3
2
2
6.3
3
3
2
2
6.4
3
3
2
2
6.5
3
3
2
2
6.6
3
3
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
DP1020
Hole Depth
2
2
2
2
2
2
6.7
3
3
24.9
24.9
32.9
32.9
24.9
27.9
32.9
35.9
62.9
62.9
68.9
68.9
62
62
68
68
0.9
0.9
0.9
0.9
5
6
5
6
2
2
2
2
2
2
6.8
3
3
26.9 28.9 66.9 66

34.9 36.9 74.9 74
0.9
0.9
6
6
2
2
26.9 28.9 66.9 66

34.9 36.9 74.9 74
0.9
0.9
6
6
2
2
2
2
6.9
3
3
27.0 29.0 67.0 66

35.0 37.0 75.0 74
1.0
1.0
6
6
2
2
27.0 29.0 67.0 66

35.0 37.0 75.0 74
1.0
1.0
6
6
2
2
2
2
7.0
3
3
27.0 29.0 67.0 66

35.0 37.0 75.0 74
1.0
1.0
6
6
2
2
7.1
2
3
29.0 29.0 67.0 66

37.0 37.0 75.0 74
1.0
1.0
6
6
2
2
7.2
2
3
29.0 29.0 67.0 66

37.0 37.0 75.0 74
1.0
1.0
6
6
2
2
7.3
2
3
29.1 29.1 67.1 66

37.1 37.1 75.1 74
1.1
1.1
6
6
2
2
7.4
2
3
29.1 29.1 67.1 66

37.1 37.1 75.1 74
1.1
1.1
6
6
2
2
7.5
2
3
29.1 29.1 67.1 66

37.1 37.1 75.1 74
1.1
1.1
6
6
2
2
7.6
2
3
32.1
32.1
42.1
42.1
35.1
35.1
45.1
45.1
75.1
75.1
84.1
84.1
74
74
83
83
1.1
1.1
1.1
1.1
7
8
7
8
2
2
2
2
7.7
2
3
7.8
2
3
32.1
32.1
42.1
42.1
35.1
35.1
45.1
45.1
75.1
75.1
84.1
84.1
74
74
83
83
1.1
1.1
1.1
1.1
7
8
7
8
2
2
2
2
7.9
2
3
8.0
2
3
32.1
32.1
42.1
42.1
35.1
35.1
45.1
45.1
75.1
75.1
84.1
84.1
74
74
83
83
1.1
1.1
1.1
1.1
7
8
7
8
2
2
2
2
2
2
8.1
3
3
32.2
32.2
42.2
42.2
35.2
35.2
45.2
45.2
75.2
75.2
84.2
84.2
74
74
83
83
1.2
1.2
1.2
1.2
7
8
7
8
2
2
2
2
2
2
8.2
3
3
32.2
32.2
42.2
42.2
35.2
35.2
45.2
45.2
75.2
75.2
84.2
84.2
74
74
83
83
1.2
1.2
1.2
1.2
7
8
7
8
2
2
2
2
2
2
8.3
3
3
35.2
35.2
44.2
44.2
35.2
37.2
44.2
46.2
75.2
75.2
84.2
84.2
74
74
83
83
1.2
1.2
1.2
1.2
7
8
7
8
2
2
2
2
2
2
8.4
3
3
(mm) (l/d)
CUTTING CONDITIONS
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
MVE0670X02S070
MVE0670X02S080
MVE0670X03S070
MVE0670X03S080
MVE0680X02S070
MVE0680X02S080
MVE0680X03S070
MVE0680X03S080
MVE0690X02S070
MVE0690X02S080
MVE0690X03S070
MVE0690X03S080
MVE0700X02S070
MVE0700X02S080
MVE0700X03S070
MVE0700X03S080
MVE0710X02S080
MVE0710X03S080
MVE0720X02S080
MVE0720X03S080
MVE0730X02S080
MVE0730X03S080
MVE0740X02S080
MVE0740X03S080
MVE0750X02S080
MVE0750X03S080
MVE0760X02S080
MVE0760X03S080
MVE0770X02S080
MVE0770X03S080
MVE0780X02S080
MVE0780X03S080
MVE0790X02S080
MVE0790X03S080
MVE0800X02S080
MVE0800X03S080
MVE0810X02S090
MVE0810X02S100
MVE0810X03S090
MVE0810X03S100
MVE0820X02S090
MVE0820X02S100
MVE0820X03S090
MVE0820X03S100
MVE0830X02S090
MVE0830X02S100
MVE0830X03S090
MVE0830X03S100
MVE0840X02S090
MVE0840X02S100
MVE0840X03S090
MVE0840X03S100
N030
35.2
35.2
44.2
44.2
35.2
37.2
44.2
46.2
75.2
75.2
84.2
84.2
74
74
83
83
1.2
1.2
1.2
1.2
7
8
7
8
2
2
2
2
35.2
35.2
44.2
44.2
35.2
37.2
44.2
46.2
75.2
75.2
84.2
84.2
74
74
83
83
1.2
1.2
1.2
1.2
7
8
7
8
2
2
2
2
35.3
35.3
44.3
44.3
35.3
37.3
44.3
46.3
75.3
75.3
84.3
84.3
74
74
83
83
1.3
1.3
1.3
1.3
7
8
7
8
2
2
2
2
35.3
35.3
44.3
44.3
35.3
37.3
44.3
46.3
75.3
75.3
84.3
84.3
74
74
83
83
1.3
1.3
1.3
1.3
7
8
7
8
2
2
2
2
35.3 38.3 80.3 79

46.3 49.3 91.3 90
1.3
1.3
8
8
2
2
35.3 38.3 80.3 79

46.3 49.3 91.3 90
1.3
1.3
8
8
2
2
35.3 38.3 80.3 79

46.3 49.3 91.3 90
1.3
1.3
8
8
2
2
35.3 38.3 80.3 79

46.3 49.3 91.3 90
1.3
1.3
8
8
2
2
35.4 38.4 80.4 79

46.4 49.4 91.4 90
1.4
1.4
8
8
2
2
38.4 38.4 80.4 79

49.4 49.4 91.4 90
1.4
1.4
8
8
2
2
38.4 38.4 80.4 79

49.4 49.4 91.4 90
1.4
1.4
8
8
2
2
38.4 38.4 80.4 79

49.4 49.4 91.4 90
1.4
1.4
8
8
2
2
38.4 38.4 80.4 79

49.4 49.4 91.4 90
1.4
1.4
8
8
2
2
38.5 38.5 80.5 79

49.5 49.5 91.5 90
1.5
1.5
8
8
2
2
38.5
38.5
54.5
54.5
41.5
41.5
57.5
57.5
85.5
85.5
99.5
99.5
84
84
98
98
1.5 9
1.5 10
1.5 9
1.5 10
2
2
2
2
38.5
38.5
54.5
54.5
41.5
41.5
57.5
57.5
85.5
85.5
99.5
99.5
84
84
98
98
1.5 9
1.5 10
1.5 9
1.5 10
2
2
2
2
38.5
38.5
54.5
54.5
41.5
41.5
57.5
57.5
85.5
85.5
99.5
99.5
84
84
98
98
1.5 9
1.5 10
1.5 9
1.5 10
2
2
2
2
38.5
38.5
54.5
54.5
41.5
41.5
57.5
57.5
85.5
85.5
99.5
99.5
84
84
98
98
1.5 9
1.5 10
1.5 9
1.5 10
2
2
2
2
TECHNICAL DATA
Q001
DRILLING
2
3
5
6
5
6
DCON
5.4
0.9
0.9
0.9
0.9
PL
62
62
68
68
LF
2
5.3
3
62.9
62.9
68.9
68.9
OAL
24.9
27.9
32.9
35.9
Type
LH
2
3
24.9
24.9
32.9
32.9
Order Number
LCF
DCON
2
5.1
3
PL
Type
LF
2
2
5.0
3
3
MVE0490X02S050
MVE0490X02S060
MVE0490X03S050
MVE0490X03S060
MVE0500X02S050
MVE0500X02S060
MVE0500X03S050
MVE0500X03S060
MVE0510X02S060
MVE0510X03S060
MVE0520X02S060
MVE0520X03S060
MVE0530X02S060
MVE0530X03S060
MVE0540X02S060
MVE0540X03S060
MVE0550X02S060
MVE0550X03S060
MVE0560X02S060
MVE0560X03S060
MVE0570X02S060
MVE0570X03S060
MVE0580X02S060
MVE0580X03S060
MVE0590X02S060
MVE0590X03S060
MVE0600X02S060
MVE0600X03S060
MVE0610X02S070
MVE0610X02S080
MVE0610X03S070
MVE0610X03S080
MVE0620X02S070
MVE0620X02S080
MVE0620X03S070
MVE0620X03S080
MVE0630X02S070
MVE0630X02S080
MVE0630X03S070
MVE0630X03S080
MVE0640X02S070
MVE0640X02S080
MVE0640X03S070
MVE0640X03S080
MVE0650X02S070
MVE0650X02S080
MVE0650X03S070
MVE0650X03S080
MVE0660X02S070
MVE0660X02S080
MVE0660X03S070
MVE0660X03S080
DC
OAL
Order Number
Dimensions (mm)
Stock
LH
2
2
4.9
3
3
5.2
External Coolant
Dimensions (mm)
LCF
(mm) (l/d)
DP1020
DC
Hole Depth
External Coolant
Stock
N025
MVE
WSTAR DRILLS
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
3
2
9.2
3
9.3
2
3
9.4
2
3
9.5
2
3
9.6
2
3
9.7
2
3
9.8
2
3
9.9
2
3
10.0
2
3
2
2
3
3
2
2
3
3
8.5
8.6
8.7
8.8
8.9
9.0
DRILLING
9.1
10.1
10.2
N026
MVE0850X02S090
MVE0850X02S100
MVE0850X03S090
MVE0850X03S100
MVE0860X02S090
MVE0860X02S100
MVE0860X03S090
MVE0860X03S100
MVE0870X02S090
MVE0870X02S100
MVE0870X03S090
MVE0870X03S100
MVE0880X02S090
MVE0880X02S100
MVE0880X03S090
MVE0880X03S100
MVE0890X02S090
MVE0890X02S100
MVE0890X03S090
MVE0890X03S100
MVE0900X02S090
MVE0900X02S100
MVE0900X03S090
MVE0900X03S100
MVE0910X02S100
MVE0910X03S100
MVE0920X02S100
MVE0920X03S100
MVE0930X02S100
MVE0930X03S100
MVE0940X02S100
MVE0940X03S100
MVE0950X02S100
MVE0950X03S100
MVE0960X02S100
MVE0960X03S100
MVE0970X02S100
MVE0970X03S100
MVE0980X02S100
MVE0980X03S100
MVE0990X02S100
MVE0990X03S100
MVE1000X02S100
MVE1000X03S100
MVE1010X02S110
MVE1010X02S120
MVE1010X03S110
MVE1010X03S120
MVE1020X02S110
MVE1020X02S120
MVE1020X03S110
MVE1020X03S120
2
2
2
2
54.5 57.5 99.5 98 1.5 9

54.5 57.5 99.5 98 1.5 10
2
2
3
3
41.6 41.6 85.6 84 1.6 9

41.6 43.6 85.6 84 1.6 10
2
2
2
2
56.6 56.6 99.6 98 1.6 9

56.6 58.6 99.6 98 1.6 10
2
2
3
3
41.6 41.6 85.6 84 1.6 9

41.6 43.6 85.6 84 1.6 10
2
2
2
2
56.6 56.6 99.6 98 1.6 9

56.6 58.6 99.6 98 1.6 10
2
2
3
3
41.6 41.6 85.6 84 1.6 9

41.6 43.6 85.6 84 1.6 10
2
2
2
2
56.6 56.6 99.6 98 1.6 9

56.6 58.6 99.6 98 1.6 10
2
2
3
3
41.6 41.6 85.6 84 1.6 9

41.6 43.6 85.6 84 1.6 10
2
2
2
2
56.6 56.6 99.6 98 1.6 9

56.6 58.6 99.6 98 1.6 10
2
2
3
3
41.6 41.6 85.6 84 1.6 9

41.6 43.6 85.6 84 1.6 10
2
2
2
2
56.6 56.6 99.6 98 1.6 9

56.6 58.6 99.6 98 1.6 10
2
2
3
3
41.7 44.7 90.7 89 1.7 10

59.7 62.7 106.7 105 1.7 10
2
2
2
2
41.7 44.7 90.7 89 1.7 10

59.7 62.7 106.7 105 1.7 10
2
2
3
3
41.7 44.7 90.7 89 1.7 10

59.7 62.7 106.7 105 1.7 10
2
2
2
2
41.7 44.7 90.7 89 1.7 10

59.7 62.7 106.7 105 1.7 10
2
2
3
3
41.7 44.7 90.7 89 1.7 10

59.7 62.7 106.7 105 1.7 10
2
2
11.1
2
3
44.7 44.7 90.7 89 1.7 10

61.7 61.7 106.7 105 1.7 10
2
2
11.2
2
3
44.8 44.8 90.8 89 1.8 10

61.8 61.8 106.8 105 1.8 10
2
2
11.3
2
3
44.8 44.8 90.8 89 1.8 10

61.8 61.8 106.8 105 1.8 10
2
2
11.4
2
3
44.8 44.8 90.8 89 1.8 10

61.8 61.8 106.8 105 1.8 10
2
2
11.5
2
3
44.8 44.8 90.8 89 1.8 10

61.8 61.8 106.8 105 1.8 10
2
2
11.6
2
3
44.8 47.8 96.8 95 1.8 11

44.8 47.8 96.8 95 1.8 12
2
2
11.7
2
3
67.8 70.8 115.8 114 1.8 11

67.8 70.8 115.8 114 1.8 12
2
2
11.8
2
3
44.9 47.9 96.9 95 1.9 11

44.9 47.9 96.9 95 1.9 12
2
2
11.9
2
3
67.9 70.9 115.9 114 1.9 11

67.9 70.9 115.9 114 1.9 12
2
2
12.0
2
3
10.3
10.4
10.5
10.6
10.7
10.8
10.9
11.0
MVE1030X02S110
MVE1030X02S120
MVE1030X03S110
MVE1030X03S120
MVE1040X02S110
MVE1040X02S120
MVE1040X03S110
MVE1040X03S120
MVE1050X02S110
MVE1050X02S120
MVE1050X03S110
MVE1050X03S120
MVE1060X02S110
MVE1060X02S120
MVE1060X03S110
MVE1060X03S120
MVE1070X02S110
MVE1070X02S120
MVE1070X03S110
MVE1070X03S120
MVE1080X02S110
MVE1080X02S120
MVE1080X03S110
MVE1080X03S120
MVE1090X02S110
MVE1090X02S120
MVE1090X03S110
MVE1090X03S120
MVE1100X02S110
MVE1100X02S120
MVE1100X03S110
MVE1100X03S120
MVE1110X02S120
MVE1110X03S120
MVE1120X02S120
MVE1120X03S120
MVE1130X02S120
MVE1130X03S120
MVE1140X02S120
MVE1140X03S120
MVE1150X02S120
MVE1150X03S120
MVE1160X02S120
MVE1160X03S120
MVE1170X02S120
MVE1170X03S120
MVE1180X02S120
MVE1180X03S120
MVE1190X02S120
MVE1190X03S120
MVE1200X02S120
MVE1200X03S120
DCON
PL
LF
(mm) (l/d)
38.5 41.5 85.5 84 1.5 9

38.5 41.5 85.5 84 1.5 10
Order Number
OAL
DC
LH
Type
Dimensions (mm)
Stock
DP1020
DCON
PL
LF
OAL
LH
Order Number
Hole Depth
External Coolant
Dimensions (mm)
LCF
(mm) (l/d)
DP1020
DC
Hole Depth
External Coolant
Stock
LCF
CARBIDE
Type
44.9 47.9 96.9 95 1.9 11

44.9 47.9 96.9 95 1.9 12
2
2
67.9 70.9 115.9 114 1.9 11

67.9 70.9 115.9 114 1.9 12
2
2
44.9 47.9 96.9 95 1.9 11

44.9 47.9 96.9 95 1.9 12
2
2
67.9 70.9 115.9 114 1.9 11

67.9 70.9 115.9 114 1.9 12
2
2
44.9 47.9 96.9 95 1.9 11

44.9 47.9 96.9 95 1.9 12
2
2
67.9 70.9 115.9 114 1.9 11

67.9 70.9 115.9 114 1.9 12
2
2
48.9 48.9 96.9 95 1.9 11

48.9 49.9 96.9 95 1.9 12
2
2
69.9 69.9 115.9 114 1.9 11

69.9 70.9 115.9 114 1.9 12
2
2
48.9 48.9 96.9 95 1.9 11

48.9 49.9 96.9 95 1.9 12
2
2
69.9 69.9 115.9 114 1.9 11

69.9 70.9 115.9 114 1.9 12
2
2
49.0 49.0 97.0 95 2.0 11

49.0 50.0 97.0 95 2.0 12
2
2
70.0 70.0 116.0 114 2.0 11

70.0 71.0 116.0 114 2.0 12
2
2
49.0 49.0 97.0 95 2.0 11

49.0 50.0 97.0 95 2.0 12
2
2
70.0 70.0 116.0 114 2.0 11

70.0 71.0 116.0 114 2.0 12
2
2
49.0 49.0 97.0 95 2.0 11

49.0 50.0 97.0 95 2.0 12
2
2
70.0 70.0 116.0 114 2.0 11

70.0 71.0 116.0 114 2.0 12
2
2
49.0 52.0 97.0 95 2.0 12

73.0 76.0 123.0 121 2.0 12
2
2
49.0 52.0 97.0 95 2.0 12

73.0 76.0 123.0 121 2.0 12
2
2
49.1 52.1 97.1 95 2.1 12

73.1 76.1 123.1 121 2.1 12
2
2
49.1 52.1 97.1 95 2.1 12

73.1 76.1 123.1 121 2.1 12
2
2
49.1 52.1 97.1 95 2.1 12

73.1 76.1 123.1 121 2.1 12
2
2
49.1 49.1 97.1 95 2.1 12

75.1 75.1 123.1 121 2.1 12
2
2
49.1 49.1 97.1 95 2.1 12

75.1 75.1 123.1 121 2.1 12
2
2
49.1 49.1 97.1 95 2.1 12

75.1 75.1 123.1 121 2.1 12
2
2
49.2 49.2 97.2 95 2.2 12

75.2 75.2 123.2 121 2.2 12
2
2
49.2 49.2 97.2 95 2.2 12

75.2 75.2 123.2 121 2.2 12
2
2
CARBIDE
12.2
12.3
12.4
12.5
12.6
12.7
12.8
12.9
13.0
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
a
r
13.1
2
3
13.2
2
3
13.3
2
3
13.4
2
3
13.5
2
3
13.6
2
3
MVE1210X02S130
MVE1210X02S140
MVE1210X03S130
MVE1210X03S140
MVE1220X02S130
MVE1220X02S140
MVE1220X03S130
MVE1220X03S140
MVE1230X02S130
MVE1230X02S140
MVE1230X03S130
MVE1230X03S140
MVE1240X02S130
MVE1240X02S140
MVE1240X03S130
MVE1240X03S140
MVE1250X02S130
MVE1250X02S140
MVE1250X03S130
MVE1250X03S140
MVE1260X02S130
MVE1260X02S140
MVE1260X03S130
MVE1260X03S140
MVE1270X02S130
MVE1270X02S140
MVE1270X03S130
MVE1270X03S140
MVE1280X02S130
MVE1280X02S140
MVE1280X03S130
MVE1280X03S140
MVE1290X02S130
MVE1290X02S140
MVE1290X03S130
MVE1290X03S140
MVE1300X02S130
MVE1300X02S140
MVE1300X03S130
MVE1300X03S140
MVE1310X02S140
MVE1310X03S140
MVE1320X02S140
MVE1320X03S140
MVE1330X02S140
MVE1330X03S140
MVE1340X02S140
MVE1340X03S140
MVE1350X02S140
MVE1350X03S140
MVE1360X02S140
MVE1360X03S140
2
2
13.7
2
3
78.2 81.2 139.2 137 2.2 13

78.2 81.2 139.2 137 2.2 14
2
2
13.8
2
3
53.2 56.2 104.2 102 2.2 13

53.2 56.2 104.2 102 2.2 14
2
2
13.9
2
3
78.2 81.2 139.2 137 2.2 13

78.2 81.2 139.2 137 2.2 14
2
2
14.0
2
3
53.2 56.2 104.2 102 2.2 13

53.2 56.2 104.2 102 2.2 14
2
2
78.2 81.2 139.2 137 2.2 13

78.2 81.2 139.2 137 2.2 14
2
2
53.3 56.3 104.3 102 2.3 13

53.3 56.3 104.3 102 2.3 14
2
2
78.3 81.3 139.3 137 2.3 13

78.3 81.3 139.3 137 2.3 14
2
2
53.3 56.3 104.3 102 2.3 13

53.3 56.3 104.3 102 2.3 14
2
2
78.3 81.3 139.3 137 2.3 13

78.3 81.3 139.3 137 2.3 14
2
2
53.3 53.3 104.3 102 2.3 13

53.3 53.3 104.3 102 2.3 14
2
2
80.3 80.3 139.3 137 2.3 13

80.3 80.3 139.3 137 2.3 14
2
2
53.3 53.3 104.3 102 2.3 13

53.3 53.3 104.3 102 2.3 14
2
2
80.3 80.3 139.3 137 2.3 13

80.3 80.3 139.3 137 2.3 14
2
2
53.3 53.3 104.3 102 2.3 13

53.3 53.3 104.3 102 2.3 14
2
2
80.3 80.3 139.3 137 2.3 13

80.3 80.3 139.3 137 2.3 14
2
2
53.3 53.3 104.3 102 2.3 13

53.3 53.3 104.3 102 2.3 14
2
2
80.3 80.3 139.3 137 2.3 13

80.3 80.3 139.3 137 2.3 14
2
2
53.4 53.4 104.4 102 2.4 13

53.4 53.4 104.4 102 2.4 14
2
2
80.4 80.4 139.4 137 2.4 13

80.4 80.4 139.4 137 2.4 14
2
2
56.4 59.4 109.4 107 2.4 14

86.4 89.4 149.4 147 2.4 14
2
2
56.4 59.4 109.4 107 2.4 14

86.4 89.4 149.4 147 2.4 14
2
2
56.4 59.4 109.4 107 2.4 14

86.4 89.4 149.4 147 2.4 14
2
2
56.4 59.4 109.4 107 2.4 14

86.4 89.4 149.4 147 2.4 14
2
2
56.5 59.5 109.5 107 2.5 14

86.5 89.5 149.5 147 2.5 14
2
2
15.1
2
3
56.5 56.5 109.5 107 2.5 14

88.5 88.5 149.5 147 2.5 14
2
2
15.2
2
3
14.1
14.2
14.3
14.4
14.5
14.6
14.7
14.8
14.9
15.0
CUTTING CONDITIONS
2
2
3
3
2
2
3
3
2
2
3
3
2
2
r
r
a
r
r
r
3
3
2
2
3
3
2
2
3
3
r
r
a
r
2
2
3
3
2
2
3
3
2
2
r
r
r
a
r
r
r
3
3
2
2
3
3
MVE1370X02S140
MVE1370X03S140
MVE1380X02S140
MVE1380X03S140
MVE1390X02S140
MVE1390X03S140
MVE1400X02S140
MVE1400X03S140
MVE1410X02S150
MVE1410X02S160
MVE1410X03S150
MVE1410X03S160
MVE1420X02S150
MVE1420X02S160
MVE1420X03S150
MVE1420X03S160
MVE1430X02S150
MVE1430X02S160
MVE1430X03S150
MVE1430X03S160
MVE1440X02S150
MVE1440X02S160
MVE1440X03S150
MVE1440X03S160
MVE1450X02S150
MVE1450X02S160
MVE1450X03S150
MVE1450X03S160
MVE1460X02S150
MVE1460X02S160
MVE1460X03S150
MVE1460X03S160
MVE1470X02S150
MVE1470X02S160
MVE1470X03S150
MVE1470X03S160
MVE1480X02S150
MVE1480X02S160
MVE1480X03S150
MVE1480X03S160
MVE1490X02S150
MVE1490X02S160
MVE1490X03S150
MVE1490X03S160
MVE1500X02S150
MVE1500X02S160
MVE1500X03S150
MVE1500X03S160
MVE1510X02S160
MVE1510X03S160
MVE1520X02S160
MVE1520X03S160
N030
DCON
PL
LF
OAL
LH
(mm) (l/d)
53.2 56.2 104.2 102 2.2 13

53.2 56.2 104.2 102 2.2 14
Order Number
LCF
DC
DP1020
Type
Hole Depth
DCON
PL
LF
OAL
LH
Order Number
Dimensions (mm)
Stock
Type
56.5 56.5 109.5 107 2.5 14

88.5 88.5 149.5 147 2.5 14
2
2
56.5 56.5 109.5 107 2.5 14

88.5 88.5 149.5 147 2.5 14
2
2
56.5 56.5 109.5 107 2.5 14

88.5 88.5 149.5 147 2.5 14
2
2
56.5 56.5 109.5 107 2.5 14

88.5 88.5 149.5 147 2.5 14
2
2
58.6 61.6 113.6 111

58.6 61.6 113.6 111
2.6 15
2.6 16
2
2
91.6 94.6 155.6 153 2.6 15

91.6 94.6 155.6 153 2.6 16
2
2
58.6 61.6 113.6 111

58.6 61.6 113.6 111
2.6 15
2.6 16
2
2
91.6 94.6 155.6 153 2.6 15

91.6 94.6 155.6 153 2.6 16
2
2
58.6 61.6 113.6 111

58.6 61.6 113.6 111
2.6 15
2.6 16
2
2
91.6 94.6 155.6 153 2.6 15

91.6 94.6 155.6 153 2.6 16
2
2
58.6 61.6 113.6 111

58.6 61.6 113.6 111
2.6 15
2.6 16
2
2
91.6 94.6 155.6 153 2.6 15

91.6 94.6 155.6 153 2.6 16
2
2
58.6 61.6 113.6 111

58.6 61.6 113.6 111
2.6 15
2.6 16
2
2
91.6 94.6 155.6 153 2.6 15

91.6 94.6 155.6 153 2.6 16
2
2
58.7 58.7 113.7 111

58.7 58.7 113.7 111
2.7 15
2.7 16
2
2
93.7 93.7 155.7 153 2.7 15

93.7 93.7 155.7 153 2.7 16
2
2
58.7 58.7 113.7 111

58.7 58.7 113.7 111
2.7 15
2.7 16
2
2
93.7 93.7 155.7 153 2.7 15

93.7 93.7 155.7 153 2.7 16
2
2
58.7 58.7 113.7 111

58.7 58.7 113.7 111
2.7 15
2.7 16
2
2
93.7 93.7 155.7 153 2.7 15

93.7 93.7 155.7 153 2.7 16
2
2
58.7 58.7 113.7 111

58.7 58.7 113.7 111
2.7 15
2.7 16
2
2
93.7 93.7 155.7 153 2.7 15

93.7 93.7 155.7 153 2.7 16
2
2
58.7 58.7 113.7 111

58.7 58.7 113.7 111
2.7 15
2.7 16
2
2
93.7 93.7 155.7 153 2.7 15

93.7 93.7 155.7 153 2.7 16
2
2
60.7 63.7 117.7 115 2.7 16

96.7 99.7 162.7 160 2.7 16
2
2
60.8 63.8 117.8 115 2.8 16

96.8 99.8 162.8 160 2.8 16
2
2
TECHNICAL DATA
Q001
DRILLING
12.1
External Coolant
Dimensions (mm)
LCF
(mm) (l/d)
DP1020
DC
Hole Depth
External Coolant
Stock
N027
MVE
WSTAR DRILLS
2
15.3
3
15.4
2
3
15.5
2
3
15.6
2
3
15.7
2
3
15.8
2
3
15.9
2
3
16.0
2
3
2
2
3
3
16.1
16.2
16.3
16.4
DRILLING
16.5
16.6
16.7
16.8
16.9
N028
2
2
3
3
2
2
r
a
r
r
r
a
r
3
3
2
2
3
3
2
2
3
3
r
a
r
a
r
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
MVE1530X02S160
MVE1530X03S160
MVE1540X02S160
MVE1540X03S160
MVE1550X02S160
MVE1550X03S160
MVE1560X02S160
MVE1560X03S160
MVE1570X02S160
MVE1570X03S160
MVE1580X02S160
MVE1580X03S160
MVE1590X02S160
MVE1590X03S160
MVE1600X02S160
MVE1600X03S160
MVE1610X02S170
MVE1610X02S180
MVE1610X03S170
MVE1610X03S180
MVE1620X02S170
MVE1620X02S180
MVE1620X03S170
MVE1620X03S180
MVE1630X02S170
MVE1630X02S180
MVE1630X03S170
MVE1630X03S180
MVE1640X02S170
MVE1640X02S180
MVE1640X03S170
MVE1640X03S180
MVE1650X02S170
MVE1650X02S180
MVE1650X03S170
MVE1650X03S180
MVE1660X02S170
MVE1660X02S180
MVE1660X03S170
MVE1660X03S180
MVE1670X02S170
MVE1670X02S180
MVE1670X03S170
MVE1670X03S180
MVE1680X02S170
MVE1680X02S180
MVE1680X03S170
MVE1680X03S180
MVE1690X02S170
MVE1690X02S180
MVE1690X03S170
MVE1690X03S180
2
2
60.8 63.8 117.8 115 2.8 16

96.8 99.8 162.8 160 2.8 16
2
2
60.8 63.8 117.8 115 2.8 16

96.8 99.8 162.8 160 2.8 16
2
2
17.1
2
3
60.8 60.8 117.8 115 2.8 16

98.8 98.8 162.8 160 2.8 16
2
2
17.2
2
3
60.9 60.9 117.9 115 2.9 16

98.9 98.9 162.9 160 2.9 16
2
2
17.3
2
3
60.9 60.9 117.9 115 2.9 16

98.9 98.9 162.9 160 2.9 16
2
2
17.4
2
3
60.9 60.9 117.9 115 2.9 16

98.9 98.9 162.9 160 2.9 16
2
2
17.5
2
3
60.9 60.9 117.9 115 2.9 16

98.9 98.9 162.9 160 2.9 16
2
2
17.6
2
3
62.9 62.9 121.9 119 2.9 17

62.9 62.9 121.9 119 2.9 18
2
2
17.7
2
3
104.9 104.9 169.9 167 2.9 17

104.9 104.9 169.9 167 2.9 18
2
2
17.8
2
3
62.9 62.9 121.9 119 2.9 17

62.9 62.9 121.9 119 2.9 18
2
2
17.9
2
3
104.9 104.9 169.9 167 2.9 17

104.9 104.9 169.9 167 2.9 18
2
2
18.0
2
3
63.0 63.0 122.0 119 3.0 17

63.0 63.0 122.0 119 3.0 18
2
2
2
2
105.0 105.0 170.0 167 3.0 17

105.0 105.0 170.0 167 3.0 18
2
2
3
3
63.0 63.0 122.0 119 3.0 17

63.0 63.0 122.0 119 3.0 18
2
2
2
2
105.0 105.0 170.0 167 3.0 17

105.0 105.0 170.0 167 3.0 18
2
2
3
3
63.0 63.0 122.0 119 3.0 17

63.0 63.0 122.0 119 3.0 18
2
2
2
2
105.0 105.0 170.0 167 3.0 17

105.0 105.0 170.0 167 3.0 18
2
2
3
3
63.0 63.0 122.0 119 3.0 17

63.0 63.0 122.0 119 3.0 18
2
2
2
2
105.0 105.0 170.0 167 3.0 17

105.0 105.0 170.0 167 3.0 18
2
2
3
3
63.0 63.0 122.0 119 3.0 17

63.0 63.0 122.0 119 3.0 18
2
2
105.0 105.0 170.0 167 3.0 17

105.0 105.0 170.0 167 3.0 18
2
2
63.1 63.1 122.1 119 3.1 17

63.1 63.1 122.1 119 3.1 18
2
2
105.1 105.1 170.1 167 3.1 17

105.1 105.1 170.1 167 3.1 18
2
2
63.1 63.1 122.1 119 3.1 17

63.1 63.1 122.1 119 3.1 18
2
2
105.1 105.1 170.1 167 3.1 17

105.1 105.1 170.1 167 3.1 18
2
2
17.0
18.1
18.2
18.3
18.4
18.5
18.6
18.7
2
2
3
3
r
a
r
2
2
3
3
2
2
3
3
2
2
3
3
MVE1700X02S170
MVE1700X02S180
MVE1700X03S170
MVE1700X03S180
MVE1710X02S180
MVE1710X03S180
MVE1720X02S180
MVE1720X03S180
MVE1730X02S180
MVE1730X03S180
MVE1740X02S180
MVE1740X03S180
MVE1750X02S180
MVE1750X03S180
MVE1760X02S180
MVE1760X03S180
MVE1770X02S180
MVE1770X03S180
MVE1780X02S180
MVE1780X03S180
MVE1790X02S180
MVE1790X03S180
MVE1800X02S180
MVE1800X03S180
MVE1810X02S190
MVE1810X02S200
MVE1810X03S190
MVE1810X03S200
MVE1820X02S190
MVE1820X02S200
MVE1820X03S190
MVE1820X03S200
MVE1830X02S190
MVE1830X02S200
MVE1830X03S190
MVE1830X03S200
MVE1840X02S190
MVE1840X02S200
MVE1840X03S190
MVE1840X03S200
MVE1850X02S190
MVE1850X02S200
MVE1850X03S190
MVE1850X03S200
MVE1860X02S190
MVE1860X02S200
MVE1860X03S190
MVE1860X03S200
MVE1870X02S190
MVE1870X02S200
MVE1870X03S190
MVE1870X03S200
DCON
PL
LF
(mm) (l/d)
60.8 63.8 117.8 115 2.8 16

96.8 99.8 162.8 160 2.8 16
Order Number
OAL
DC
LH
Type
Dimensions (mm)
Stock
DP1020
DCON
PL
LF
OAL
LH
Order Number
Hole Depth
External Coolant
Dimensions (mm)
LCF
(mm) (l/d)
DP1020
DC
Hole Depth
External Coolant
Stock
LCF
CARBIDE
Type
63.1 63.1 122.1 119 3.1 17

63.1 63.1 122.1 119 3.1 18
2
2
105.1 105.1 170.1 167 3.1 17

105.1 105.1 170.1 167 3.1 18
2
2
65.1 65.1 126.1 123 3.1 18

105.1 105.1 170.1 167 3.1 18
2
2
65.1 65.1 126.1 123 3.1 18

105.1 105.1 170.1 167 3.1 18
2
2
65.1 65.1 126.1 123 3.1 18

105.1 105.1 170.1 167 3.1 18
2
2
65.2 65.2 126.2 123 3.2 18

105.2 105.2 170.2 167 3.2 18
2
2
65.2 65.2 126.2 123 3.2 18

105.2 105.2 170.2 167 3.2 18
2
2
65.2 65.2 126.2 123 3.2 18

105.2 105.2 170.2 167 3.2 18
2
2
65.2 65.2 126.2 123 3.2 18

105.2 105.2 170.2 167 3.2 18
2
2
65.2 65.2 126.2 123 3.2 18

105.2 105.2 170.2 167 3.2 18
2
2
65.3 65.3 126.3 123 3.3 18

105.3 105.3 170.3 167 3.3 18
2
2
65.3 65.3 126.3 123 3.3 18

105.3 105.3 170.3 167 3.3 18
2
2
67.3 67.3 130.3 127 3.3 19

67.3 67.3 130.3 127 3.3 20
2
2
117.3 117.3 182.3 179 3.3 19

117.3 117.3 182.3 179 3.3 20
2
2
67.3 67.3 130.3 127 3.3 19

67.3 67.3 130.3 127 3.3 20
2
2
117.3 117.3 182.3 179 3.3 19

117.3 117.3 182.3 179 3.3 20
2
2
67.3 67.3 130.3 127 3.3 19

67.3 67.3 130.3 127 3.3 20
2
2
117.3 117.3 182.3 179 3.3 19

117.3 117.3 182.3 179 3.3 20
2
2
67.3 67.3 130.3 127 3.3 19

67.3 67.3 130.3 127 3.3 20
2
2
117.3 117.3 182.3 179 3.3 19

117.3 117.3 182.3 179 3.3 20
2
2
67.4 67.4 130.4 127 3.4 19

67.4 67.4 130.4 127 3.4 20
2
2
117.4 117.4 182.4 179 3.4 19

117.4 117.4 182.4 179 3.4 20
2
2
67.4 67.4 130.4 127 3.4 19

67.4 67.4 130.4 127 3.4 20
2
2
117.4 117.4 182.4 179 3.4 19

117.4 117.4 182.4 179 3.4 20
2
2
67.4 67.4 130.4 127 3.4 19

67.4 67.4 130.4 127 3.4 20
2
2
117.4 117.4 182.4 179 3.4 19

117.4 117.4 182.4 179 3.4 20
2
2
CARBIDE
18.9
19.0
r
r
3
3
2
2
3
3
2
2
3
3
19.1
2
3
19.2
2
3
19.3
2
3
19.4
2
3
19.5
2
3
19.6
2
3
19.7
2
3
19.8
2
3
19.9
2
3
20.0
2
3
MVE1880X02S190
MVE1880X02S200
MVE1880X03S190
MVE1880X03S200
MVE1890X02S190
MVE1890X02S200
MVE1890X03S190
MVE1890X03S200
MVE1900X02S190
MVE1900X02S200
MVE1900X03S190
MVE1900X03S200
MVE1910X02S200
MVE1910X03S200
MVE1920X02S200
MVE1920X03S200
MVE1930X02S200
MVE1930X03S200
MVE1940X02S200
MVE1940X03S200
MVE1950X02S200
MVE1950X03S200
MVE1960X02S200
MVE1960X03S200
MVE1970X02S200
MVE1970X03S200
MVE1980X02S200
MVE1980X03S200
MVE1990X02S200
MVE1990X03S200
MVE2000X02S200
MVE2000X03S200
DCON
PL
LF
OAL
LH
Order Number
Type
67.4 67.4 130.4 127 3.4 19

67.4 67.4 130.4 127 3.4 20
2
2
117.4 117.4 182.4 179 3.4 19

117.4 117.4 182.4 179 3.4 20
2
2
67.4 67.4 130.4 127 3.4 19

67.4 67.4 130.4 127 3.4 20
2
2
117.4 117.4 182.4 179 3.4 19

117.4 117.4 182.4 179 3.4 20
2
2
67.5 67.5 130.5 127 3.5 19

67.5 67.5 130.5 127 3.5 20
2
2
117.5 117.5 182.5 179 3.5 19

117.5 117.5 182.5 179 3.5 20
2
2
69.5 69.5 134.5 131 3.5 20

117.5 117.5 182.5 179 3.5 20
2
2
69.5 69.5 134.5 131 3.5 20

117.5 117.5 182.5 179 3.5 20
2
2
69.5 69.5 134.5 131 3.5 20

117.5 117.5 182.5 179 3.5 20
2
2
69.5 69.5 134.5 131 3.5 20

117.5 117.5 182.5 179 3.5 20
2
2
69.5 69.5 134.5 131 3.5 20

117.5 117.5 182.5 179 3.5 20
2
2
69.6 69.6 134.6 131 3.6 20

117.6 117.6 182.6 179 3.6 20
2
2
69.6 69.6 134.6 131 3.6 20

117.6 117.6 182.6 179 3.6 20
2
2
69.6 69.6 134.6 131 3.6 20

117.6 117.6 182.6 179 3.6 20
2
2
69.6 69.6 134.6 131 3.6 20

117.6 117.6 182.6 179 3.6 20
2
2
69.6 69.6 134.6 131 3.6 20

117.6 117.6 182.6 179 3.6 20
2
2
DRILLING
18.8
2
2
Dimensions (mm)
LCF
(mm) (l/d)
DP1020
DC
Hole Depth
External Coolant
Stock
CUTTING CONDITIONS
N030
TECHNICAL DATA
Q001
N029
CARBIDE
MVE
WSTAR DRILLS
Work
Material
Carbon steel, Alloy steel (180 280HB)
AISI 1010 etc
AISI 4340 etc
Dia.
DC
(mm)
Revolution
(min-1)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
6400
5500
4400
4000
3300
2800
2500
1900
1500
Work
Material
Feed rate
(Min. Max.)
(mm/rev)
0.1
0.12
0.15
0.2
0.23
0.27
0.31
0.33
0.35
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
0.1
0.12
0.15
0.2
0.23
0.27
0.31
0.33
0.35
5400
4700
3800
3500
2900
2500
2200
1600
1300
0.09
0.11
0.14
0.18
0.21
0.23
0.26
0.29
0.3
(0.06 0.12)
(0.07 0.14)
(0.09 0.18)
(0.11 0.24)
(0.16 0.25)
(0.19 0.27)
(0.23 0.29)
(0.24 0.33)
(0.26 0.34)
No 45 B etc
60-40-8 etc
Dia.
DC
(mm)
Revolution
(min-1)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
1900
1500
1200
1200
900
700
600
400
300
Feed rate
(Min. Max.)
(mm/rev)
0.07
0.08
0.1
0.13
0.14
0.16
0.18
0.19
0.2
(0.05 0.08)
(0.06 0.10)
(0.07 0.13)
(0.09 0.17)
(0.10 0.18)
(0.12 0.19)
(0.15 0.20)
(0.15 0.23)
(0.15 0.24)
DRILLING
5900
5100
4100
3700
3100
2700
2300
1700
1400
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
Work
Material
N030
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
Dia.
DC
(mm)
Revolution
(min-1)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
7900
6300
5000
4500
3500
2800
2600
1900
1700
Feed rate
(Min. Max.)
(mm/rev)
0.1
0.12
0.15
0.2
0.23
0.27
0.31
0.33
0.35
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
6900
5500
4400
3700
2900
2300
2100
1500
1300
0.1
0.12
0.15
0.2
0.25
0.29
0.33
0.35
0.37
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.31)
(0.22 0.35)
(0.28 0.37)
(0.28 0.42)
(0.30 0.44)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
6400
5100
4100
3500
2700
2200
1900
1400
1200
0.1
0.12
0.15
0.2
0.23
0.27
0.31
0.33
0.35
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
Hardened Steel (40 55HRC)
Inconel718 etc
AISI H13, L6 etc

Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
1900
1500
1200
1200
900
700
600
400
400
0.07
0.09
0.11
0.14
0.14
0.16
0.16
0.18
0.19
(0.05 0.09)
(0.06 0.11)
(0.08 0.14)
(0.09 0.19)
(0.11 0.17)
(0.12 0.19)
(0.13 0.18)
(0.14 0.21)
(0.15 0.22)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
1900
1500
1200
1200
900
700
600
400
400
0.07
0.09
0.11
0.14
0.14
0.16
0.16
0.18
0.19
(0.05 0.09)
(0.06 0.11)
(0.08 0.14)
(0.09 0.19)
(0.11 0.17)
(0.12 0.19)
(0.13 0.18)
(0.14 0.21)
(0.15 0.22)
CARBIDE
y OPERATIONAL GUIDANCE
Drill Length
Drill Installation
Installation Tolerance
A > DC x 1.5
Do not clamp on the flutes.
Run-out < 0.03mm
Interrupted Cutting
Stepped Holes
Burring and Workpiece Chipping
Adjusting Screw
Drill Holding
Thrust bearing type collet

chuck holds the drill securely.
Thin Workpiece
DC
One Process
zLower the feed
If Bending
Occurs
when drilling
the interrupted
part.
Support
the Workpiece
zSpot face with

an end mill
prior to drilling.
Coolant Method (MVE)
Through Coolant Type (MVS)

Spindles
Through
Coolant Type
Two coolant positions, at the

end and at the center are ideal.
Revolving
Coolant
Machine Type
Coolant pressure is approx.

0.51MPa (<&5:23MPa).
Coolant volume is 1.54.0l/min.
zDivide the two processes.

xDrill the larger hole first.
*A tool for machining both
chamfer and spot face can
be produced to order.
zLower the feed rate by 50%

at the end of through
cutting.
xAdd a 45chamfer.
cChange the point angle.
Coolant Handling
<MVS Type>
1) Small particles of swarf will

jam in the oil hole of small
diameter drills. Always use
a fine mesh filter as a
preventative measure.
2) Dirt and dust particles
adhere to the oil in old
coolant and prevent an
efficient flow. Regular
coolant exchange is
recommended.
DRILLING
Requires Prior
Machining
TECHNICAL DATA
Q001
N031
MWS
WSTAR DRILLS
Steel
through to difficult-to-cut materials.
0.5 < DC<1 1 < DC<2.95
+0.009
0
0
0.006
h6
PL
y SB Type
LF
Note 3
DC
(For pilot holes)
+0.014
0
0
0.006
LCF
LH
Type1
Type2
OAL
PL
LF
145
DC
DCON(h6)
a For high accuracy and efficient drilling of carbon steels
DCON(h6)
CARBIDE
LCF
LH
OAL
y LB/XB Type (& 0.50 & 2.95)
0.5 < DC<1 1 < DC<2.95

0
0.009
0
0.006
h6
PL
0
0.014
0
0.006
y DB Type (& 0.50 & 2.95)
LCF
LH
LF
140
DC
Type3
OAL
PL
DCON(h6)
Note 3
DC
DCON(h6)
LF
LCF
LH
Type4
OAL
(Note) MWS drills are suitable for use with shrink fit holders.
DC=3
h6
0
0.014
0
0.006
3<DC < 6 6<DC < 10 10<DC < 1818<DC < 25

0
0.018
0
0.008
&3.0&6.0
y X10DB/X15DB/X20DB/X25DB/X30DB Type (& 3 & 14, l/d > 10)
Type5
OAL
DC=3
3<DC < 6
6<DC < 10
10<DC < 14
0.017
0.031
0
0.006
0.025
0.043
0
0.008
0.033
0.055
0
0.009
0.041
0.068
0
0.011
140
LF
LCF
LH
OAL
(Note 1) MWS type bigger than&5.0 have a recess in the end face.
(Note 2) MWS drills are suitable for use with shrink fit holders.
(Note 3) Point Anglel:Type1 140 for drill diameter & 0.50-2.0 and 145 for & 2.05-2.95.
Type3 135 for drill diameter & 0.50-2.0 and 140 for & 2.05-2.95.
s To order non-stocked size of the DB Type (& 3-& 14, l/d>10), please provide the following.
zDrill name
xWorkpiece material, drilling depth and required accuracy.
cDrilling mode (through hole, blind hole, cross hole...) vDrill dimensions (dimensions specified in the drawing above).
Please contact us for inquiries.
N032
0
0.033
0
0.013
DCON(h6)
PL
DC
DRILLING
LF
LCF
LH
h6
0
0.027
0
0.011
140
DC
PL
0
0.022
0
0.009
DCON(h6)
y MB/LB/X8DB Type (& 3 & 25)
Type6
CARBIDE
a
a
12
1
0.52 5
12
1
0.53 5
12
1
0.54 5
12
1
0.55 5
12
a
a
a
a
a
a
a
a
0.56 5
12
1
0.57 5
12
a
a
a
0.58 5
12
1
0.59 5
12
a
a
a
0.60 5
12
1
0.61 5
12
1
0.62 5
12
a
a
a
a
0.63 5
12
1
0.64 5
12
a
a
a
0.65 5
12
1
0.66 5
12
a
a
a
1
3
3
0.68 5
12
2.69 7.29 47.09 47 0.09 3

8.09 13.09 47.09 47 0.11 3
16.09 21.09 47.09 47 0.11 3
1
3
3
1
0.69 5
12
2.70 7.30 47.10 47 0.10 3

8.10 13.10 47.10 47 0.11 3
16.10 21.10 47.10 47 0.11 3
1
3
3
1
0.70 5
12
2.70 7.30 47.10 47 0.10 3

8.10 13.10 47.10 47 0.11 3
16.10 21.10 47.10 47 0.11 3
1
3
3
1
0.71 5
12
2.70 7.30 47.10 47 0.10 3

8.10 13.10 47.10 47 0.11 3
16.10 21.10 47.10 47 0.11 3
1
3
3
1
0.72 5
12
3.00 7.60 47.10 47 0.10 3

8.10 13.10 47.10 47 0.12 3
16.10 21.10 47.10 47 0.12 3
1
3
3
0.73 5
12
3.00 7.50 47.10 47 0.10 3

8.10 13.10 47.10 47 0.12 3
16.10 21.10 47.10 47 0.12 3
1
3
3
1
0.74 5
12
3.01 7.51 47.11 47 0.11 3

8.11 13.11 47.11 47 0.12 3
16.11 21.11 47.11 47 0.12 3
1
3
3
0.75 5
12
3.01 7.51 47.11 47 0.11 3

8.11 12.11 47.11 47 0.12 3
16.11 20.11 47.11 47 0.12 3
1
3
3
1
0.76 5
12
3.01 7.51 47.11 47 0.11 3

8.11 12.11 47.11 47 0.12 3
16.11 20.11 47.11 47 0.12 3
1
3
3
0.77 5
12
3.21 7.71 47.11 47 0.11 3

8.11 12.11 47.11 47 0.13 3
16.11 20.11 47.11 47 0.13 3
1
3
3
1
0.78 5
12
3.21 7.61 47.11 47 0.11 3

8.11 12.11 47.11 47 0.13 3
16.11 20.11 47.11 47 0.13 3
1
3
3
1
0.79 5
12
3.21 7.61 47.11 47 0.11 3

8.11 12.11 47.11 47 0.13 3
16.11 20.11 47.11 47 0.13 3
1
3
3
0.80 5
12
3.22 7.62 47.12 47 0.12 3

8.12 12.12 47.12 47 0.13 3
16.12 20.12 47.12 47 0.13 3
1
3
3
1
0.81 5
12
3.22 7.62 47.12 47 0.12 3

8.12 12.12 47.12 47 0.13 3
16.12 20.12 47.12 47 0.13 3
1
3
3
0.82 5
12
3.52 7.92 47.12 47 0.12 3

8.12 12.12 47.12 47 0.14 3
16.12 20.12 47.12 47 0.14 3
1
3
3
1
0.83 5
12
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
DCON
2.69 7.29 47.09 47 0.09 3

8.09 13.09 47.09 47 0.11 3
16.09 21.09 47.09 47 0.11 3
PL
LF
12
MWS0067SB
MWS0067LB
MWS0067XB
MWS0068SB
MWS0068LB
MWS0068XB
MWS0069SB
MWS0069LB
MWS0069XB
MWS0070SB
MWS0070LB
MWS0070XB
MWS0071SB
MWS0071LB
MWS0071XB
MWS0072SB
MWS0072LB
MWS0072XB
MWS0073SB
MWS0073LB
MWS0073XB
MWS0074SB
MWS0074LB
MWS0074XB
MWS0075SB
MWS0075LB
MWS0075XB
MWS0076SB
MWS0076LB
MWS0076XB
MWS0077SB
MWS0077LB
MWS0077XB
MWS0078SB
MWS0078LB
MWS0078XB
MWS0079SB
MWS0079LB
MWS0079XB
MWS0080SB
MWS0080LB
MWS0080XB
MWS0081SB
MWS0081LB
MWS0081XB
MWS0082SB
MWS0082LB
MWS0082XB
MWS0083SB
MWS0083LB
MWS0083XB
OAL
LH
0.67 5
LCF
3
3
Order Number
Type
3.52 7.82 47.12 47 0.12 3
8.12 12.12 47.12 47 0.14 3

16.12 20.12 47.12 47 0.14 3
3
3
3.52 7.82 47.12 47 0.12 3

8.12 12.12 47.12 47 0.14 3
16.12 20.12 47.12 47 0.14 3
1
3
3
3.53 7.83 47.13 47 0.13 3

8.13 12.13 47.13 47 0.14 3
16.13 20.13 47.13 47 0.14 3
1
3
3
3.53 7.83 47.13 47 0.13 3

8.13 12.13 47.13 47 0.14 3
16.13 20.13 47.13 47 0.14 3
1
3
3
3.73 8.03 50.13 50 0.13 3

10.13 14.13 50.13 50 0.15 3
20.13 24.13 50.13 50 0.15 3
1
3
3
3.73 8.03 50.13 50 0.13 3

10.13 14.13 50.13 50 0.15 3
20.13 24.13 50.13 50 0.15 3
1
3
3
3.73 7.93 50.13 50 0.13 3

10.13 14.13 50.13 50 0.15 3
20.13 24.13 50.13 50 0.15 3
1
3
3
3.73 7.93 50.13 50 0.13 3

10.13 14.13 50.13 50 0.15 3
20.13 24.13 50.13 50 0.15 3
1
3
3
3.74 7.94 50.14 50 0.14 3

10.14 14.14 50.14 50 0.16 3
20.14 24.14 50.14 50 0.16 3
1
3
3
4.04 8.24 50.14 50 0.14 3

10.14 14.14 50.14 50 0.16 3
20.14 24.14 50.14 50 0.16 3
1
3
3
4.04 8.24 50.14 50 0.14 3

10.14 14.14 50.14 50 0.16 3
20.14 24.14 50.14 50 0.16 3
1
3
3
4.04 8.14 50.14 50 0.14 3

10.14 14.14 50.14 50 0.16 3
20.14 24.14 50.14 50 0.16 3
1
3
3
4.04 8.14 50.14 50 0.14 3

10.14 14.14 50.14 50 0.16 3
20.14 24.14 50.14 50 0.16 3
1
3
3
4.05 8.15 50.15 50 0.15 3

10.15 14.15 50.15 50 0.17 3
20.15 24.15 50.15 50 0.17 3
1
3
3
4.25 8.35 50.15 50 0.15 3

10.15 14.15 50.15 50 0.17 3
20.15 24.15 50.15 50 0.17 3
1
3
3
4.25 8.35 50.15 50 0.15 3

10.15 14.15 50.15 50 0.17 3
20.15 24.15 50.15 50 0.17 3
1
3
3
4.25 8.25 50.15 50 0.15 3

10.15 14.15 50.15 50 0.17 3
20.15 24.15 50.15 50 0.17 3
1
3
3
DRILLING
0.51 5
VP15TF
8.09 13.09 47.09 47 0.10 3

16.09 21.09 47.09 47 0.10 3
DCON
12
(mm) (l/d)
PL
DC
Type
Dimensions (mm)
Stock
2.59 7.29 47.09 47 0.09 3
LF
0.50 5
MWS0050SB
MWS0050LB
MWS0050XB
MWS0051SB
MWS0051LB
MWS0051XB
MWS0052SB
MWS0052LB
MWS0052XB
MWS0053SB
MWS0053LB
MWS0053XB
MWS0054SB
MWS0054LB
MWS0054XB
MWS0055SB
MWS0055LB
MWS0055XB
MWS0056SB
MWS0056LB
MWS0056XB
MWS0057SB
MWS0057LB
MWS0057XB
MWS0058SB
MWS0058LB
MWS0058XB
MWS0059SB
MWS0059LB
MWS0059XB
MWS0060SB
MWS0060LB
MWS0060XB
MWS0061SB
MWS0061LB
MWS0061XB
MWS0062SB
MWS0062LB
MWS0062XB
MWS0063SB
MWS0063LB
MWS0063XB
MWS0064SB
MWS0064LB
MWS0064XB
MWS0065SB
MWS0065LB
MWS0065XB
MWS0066SB
MWS0066LB
MWS0066XB
OAL
LH
Order Number
Hole Depth
Internal Coolant
Dimensions (mm)
LCF
(mm) (l/d)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
(Note) Please contact us for any geometry that is not in this catalogue (e.g. different diameter and length).
a
OPERATION GUIDANCE
CUTTING CONDITIONS
N047
TECHNICAL DATA
N051,N052
Q001
N033
MWS
WSTAR DRILLS
1
0.87 5
12
1
0.88 5
12
1
0.89 5
12
1
0.90 5
12
1
0.91 5
12
a
a
a
a
a
a
a
a
a
a
a
a
0.92 5
12
1
0.93 5
12
a
a
a
0.94 5
12
0.95 5
12
0.96 5
12
0.97 5
12
0.98 5
12
0.99 5
12
10.15 14.15 50.15 50 0.17 3

20.15 24.15 50.15 50 0.17 3
3
3
12
20
25
30
1
20
25
30
1
5
12
20
25
30
1
20
25
30
1
5
12
20
25
30
1
20
25
30
1
5
MWS0100SB
MWS0100LB
MWS0100XB
MWS0100X20DB
MWS0100X25DB
MWS0100X30DB
MWS0105SB
MWS0105X20DB
MWS0105X25DB
MWS0105X30DB
MWS0110SB
MWS0110LB
MWS0110XB
MWS0110X20DB
MWS0110X25DB
MWS0110X30DB
MWS0115SB
MWS0115X20DB
MWS0115X25DB
MWS0115X30DB
MWS0120SB
MWS0120LB
MWS0120XB
MWS0120X20DB
MWS0120X25DB
MWS0120X30DB
MWS0125SB
MWS0125X20DB
MWS0125X25DB
MWS0125X30DB
MWS0130SB
MWS0130LB
MWS0130XB
MWS0130X20DB
MWS0130X25DB
MWS0130X30DB
MWS0135SB
MWS0135X20DB
MWS0135X25DB
MWS0135X30DB
MWS0140SB
MWS0140LB
MWS0140XB
MWS0140X20DB
MWS0140X25DB
MWS0140X30DB
MWS0145SB
MWS0145X20DB
MWS0145X25DB
MWS0145X30DB
4.25 8.25 50.15 50 0.15 3

10.15 14.15 50.15 50 0.18 3
20.15 24.15 50.15 50 0.18 3
1
3
3
4.56 8.56 50.16 50 0.16 3

10.16 14.16 50.16 50 0.18 3
20.16 24.16 50.16 50 0.18 3
1
3
3
4.56 8.56 50.16 50 0.16 3

10.16 14.16 50.16 50 0.18 3
20.16 24.16 50.16 50 0.18 3
1
3
3
4.56 8.56 50.16 50 0.16 3

10.16 14.16 50.16 50 0.18 3
20.16 24.16 50.16 50 0.18 3
1
3
3
4.56 8.46 50.16 50 0.16 3

10.16 14.16 50.16 50 0.18 3
20.16 24.16 50.16 50 0.18 3
1
3
3
4.56 8.46 50.16 50 0.16 3

10.16 14.16 50.16 50 0.19 3
20.16 24.16 50.16 50 0.19 3
1
3
3
4.77 8.67 50.17 50 0.17 3

10.17 14.17 50.17 50 0.19 3
20.17 24.17 50.17 50 0.19 3
1
3
3
4.77 8.67 50.17 50 0.17 3

10.17 14.17 50.17 50 0.19 3
20.17 24.17 50.17 50 0.19 3
1
3
3
4.77 8.67 50.17 50 0.17 3

10.17 14.17 50.17 50 0.19 3
20.17 24.17 50.17 50 0.19 3
1
3
3
4.77 8.57 50.17 50 0.17 3

10.17 14.17 50.17 50 0.19 3
20.17 24.17 50.17 50 0.19 3
1
3
3
4.77 8.57 50.17 50 0.17 3

10.17 14.17 50.17 50 0.20 3
20.17 24.17 50.17 50 0.20 3
1
3
3
5.07 8.87 50.17 50 0.17 3

10.17 14.17 50.17 50 0.20 3
20.17 24.17 50.17 50 0.20 3
1
3
3
5.08 8.88 50.18 50 0.18 3

10.18 14.18 50.18 50 0.20 3
20.18 24.18 50.18 50 0.20 3
1
3
3
5.08 8.88 50.18 50 0.18 3

10.18 14.18 50.18 50 0.20 3
20.18 24.18 50.18 50 0.20 3
1
3
3
5.08 8.88 50.18 50 0.18 3

10.18 14.18 50.18 50 0.21 3
20.18 24.18 50.18 50 0.21 3
1
3
3
1.00
1.05
1.10
1.15
1.20
1.25
1.30
1.35
1.40
1.45
12
20
25
30
1
20
25
30
1
5
12
20
25
30
1
20
25
30
a
r
r
r
r
N034
DCON
1
5
(mm) (l/d)
4.25 8.25 50.15 50 0.15 3
Type
PL
1
0.86 5
12
Order Number
LF
DC
5.2 8.9 55.2 55

11.2 15.2 55.2 55
0.2
0.2
3
3
1
3
23.2 27.2 55.2 55
0.2
24.2 28.2 60.2 60
0.2
28.2 32.2 66.2 66

33.2 37.2 72.2 72
0.2
0.2
3
3
3
3
5.4 9.0 55.2 55

24.2 28.2 60.2 60
0.2
0.2
3
3
1
3
29.2 33.2 66.2 66

35.2 38.2 72.2 72
0.2
0.2
3
3
3
3
5.6 9.1 55.2 55

17.2 21.2 55.2 55
0.2
0.2
3
3
1
3
23.2 27.2 55.2 55
0.2
OAL
1
0.85 5
12
Type
Dimensions (mm)
Stock
LH
DCON
12
PL
LF
0.84 5
MWS0084SB
MWS0084LB
MWS0084XB
MWS0085SB
MWS0085LB
MWS0085XB
MWS0086SB
MWS0086LB
MWS0086XB
MWS0087SB
MWS0087LB
MWS0087XB
MWS0088SB
MWS0088LB
MWS0088XB
MWS0089SB
MWS0089LB
MWS0089XB
MWS0090SB
MWS0090LB
MWS0090XB
MWS0091SB
MWS0091LB
MWS0091XB
MWS0092SB
MWS0092LB
MWS0092XB
MWS0093SB
MWS0093LB
MWS0093XB
MWS0094SB
MWS0094LB
MWS0094XB
MWS0095SB
MWS0095LB
MWS0095XB
MWS0096SB
MWS0096LB
MWS0096XB
MWS0097SB
MWS0097LB
MWS0097XB
MWS0098SB
MWS0098LB
MWS0098XB
MWS0099SB
MWS0099LB
MWS0099XB
OAL
LH
VP15TF
LCF
(mm) (l/d)
Order Number
Hole Depth
Internal Coolant
Dimensions (mm)
VP15TF
DRILLING
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
25.2 29.2 60.2 60
0.2
31.2 34.2 66.2 66

36.2 40.2 72.2 72
0.2
0.2
3
3
3
3
5.8 9.3 55.2 55

26.2 30.2 60.2 60
0.2
0.2
3
3
1
3
32.2 36.2 66.2 66

38.2 41.2 72.2 72
0.2
0.2
3
3
3
3
6.2 9.6 55.2 55

17.2 20.2 55.2 55
0.2
0.3
3
3
1
3
23.2 26.2 55.2 55
0.3
28.2 31.2 60.2 60
0.3
34.2 37.2 66.2 66

40.2 43.2 72.2 72
0.3
0.3
3
3
3
3
6.4 9.7 55.2 55

29.2 32.2 68.2 68
0.2
0.3
3
3
1
3
35.2 38.2 74.2 74

41.2 45.2 82.2 82
0.3
0.3
3
3
3
3
6.6 9.8 55.2 55

17.2 20.2 55.2 55
0.2
0.3
3
3
1
3
23.2 26.2 55.2 55
0.3
30.2 33.2 68.2 68
0.3
36.2 40.2 74.2 74

43.2 46.2 82.2 82
0.3
0.3
3
3
3
3
6.8 9.9 55.2 55

31.2 34.2 68.2 68
0.3
0.3
3
3
1
3
38.2 41.2 74.2 74

45.2 48.2 82.2 82
0.3
0.3
3
3
3
3
7.3 10.3 55.3 55

17.3 20.3 55.3 55
0.3
0.3
3
3
1
3
23.3 26.3 55.3 55
0.3
32.3 35.3 68.3 68
0.3
39.3 42.3 74.3 74

46.3 49.3 82.3 82
0.3
0.3
3
3
3
3
7.5 10.4 55.3 55

33.3 36.3 68.3 68
0.3
0.3
3
3
1
3
41.3 43.3 74.3 74

48.3 51.3 82.3 82
0.3
0.3
3
3
3
3
CARBIDE
1
5
1.60
12
20
25
30
1
20
1.65
25
30
1
5
1.70
12
20
25
30
1
20
1.75
25
30
1
5
1.80
12
20
25
30
1
20
1.85
25
30
1
5
1.90
12
20
25
30
1
20
1.95
25
30
3
3
1
3
1
20
43.3 46.3 86.3 86 0.3

51.3 54.3 95.3 95 0.3
3
3
3
3
25
30
8.3 10.9 68.3 68 0.3

22.3 25.3 68.3 68 0.3
3
3
1
3
1
5
30.3 33.3 68.3 68 0.3
12
37.3 39.3 78.3 78 0.3
20
45.3 47.3 86.3 86 0.3

53.3 55.3 95.3 95 0.3
3
3
3
3
25
30
8.5 11.0 68.3 68 0.3

38.3 40.3 78.3 78 0.3
3
3
1
3
1
20
46.3 49.3 86.3 86 0.3

54.3 57.3 95.3 95 0.3
3
3
3
3
25
30
8.7 11.1 68.3 68 0.3

22.3 24.3 68.3 68 0.4
3
3
1
3
1
5
30.3 32.3 68.3 68 0.4
12
39.3 42.3 78.3 78 0.4
20
48.3 50.3 86.3 86 0.4

56.3 59.3 95.3 95 0.4
3
3
3
3
25
30
8.9 11.2 68.3 68 0.3

40.3 43.3 84.3 84 0.4
3
3
1
3
1
20
49.3 51.3 94.3 94 0.4

58.3 60.3 102.3 102 0.4
3
3
3
3
25
30
9.3 11.5 68.3 68 0.3

22.3 24.3 68.3 68 0.4
3
3
1
3
1
5
30.3 32.3 68.3 68 0.4
41.3 44.3 84.3 84 0.4
50.3 53.3 94.3 94 0.4

59.3 62.3 102.3 102 0.4
3
3
9.5 11.6 68.3 68 0.3

43.3 45.3 84.3 84 0.4
42.3 45.3 74.3 74 0.3

50.3 52.3 82.3 82 0.3
3
3
7.9 10.6 68.3 68 0.3

36.3 38.3 78.3 78 0.3
2.05
2.10
2.15
2.20
2.25
12
20
3
3
25
30
3
3
1
3
1
20
52.3 54.3 94.3 94 0.4

61.3 63.3 102.3 102 0.4
3
3
3
3
25
30
9.7 11.8 68.3 68 0.4

22.3 24.3 68.3 68 0.4
3
3
1
3
1
5
30.3 32.3 68.3 68 0.4
12
44.3 46.3 84.3 84 0.4
20
53.3 55.3 94.3 94 0.4

63.3 65.3 102.3 102 0.4
3
3
3
3
25
30
10.0 12.0 68.4 68 0.4

45.4 47.4 84.4 84 0.4
3
3
1
3
1
20
55.4 57.4 94.4 94 0.4

64.4 66.4 102.4 102 0.4
3
3
3
3
2.30
2.35
2.40
2.45
25
30
a
r
r
r
r
1
3
30.4 32.4 68.4 68 0.4
46.4 48.4 84.4 84 0.4
56.4 58.4 94.4 94 0.4

66.4 68.4 102.4 102 0.4
3
3
3
3
10.6 12.4 74.4 74 0.3

47.4 49.4 94.4 94 0.4
3
3
1
3
57.4 59.4 107.4 107 0.4

68.4 69.4 118.4 118 0.4
3
3
3
3
10.8 12.5 74.4 74 0.3

28.4 30.4 74.4 74 0.4
3
3
1
3
38.4 40.4 74.4 74 0.4
48.4 50.4 94.4 94 0.4
59.4 60.4 107.4 107 0.4

69.4 71.4 118.4 118 0.4
3
3
3
3
11.0 12.6 74.4 74 0.3

49.4 51.4 94.4 94 0.4
3
3
1
3
60.4 62.4 107.4 107 0.4

71.4 73.4 118.4 118 0.4
3
3
3
3
11.4 12.9 74.4 74 0.4

28.4 29.4 74.4 74 0.4
3
3
1
3
38.4 39.4 74.4 74 0.4
51.4 52.4 94.4 94 0.4
62.4 63.4 107.4 107 0.4

73.4 74.4 118.4 118 0.4
3
3
3
3
11.6 13.0 74.4 74 0.4

52.4 53.4 94.4 94 0.4
3
3
1
3
63.4 64.4 107.4 107 0.4

74.4 76.4 118.4 118 0.4
3
3
3
3
11.8 13.1 74.4 74 0.4

28.4 29.4 74.4 74 0.4
3
3
1
3
38.4 39.4 74.4 74 0.4
53.4 54.4 94.4 94 0.4
64.4 66.4 107.4 107 0.4

76.4 77.4 118.4 118 0.4
3
3
3
3
12.0 13.2 74.4 74 0.4

54.4 55.4 94.4 94 0.4
3
3
1
3
66.4 67.4 107.4 107 0.4

78.4 79.4 118.4 118 0.4
3
3
3
3
12.4 13.5 74.4 74 0.4

28.4 29.4 74.4 74 0.4
3
3
1
3
38.4 39.4 74.4 74 0.4
55.4 56.4 94.4 94 0.4
67.4 68.4 107.4 107 0.4

79.4 80.4 118.4 118 0.4
3
3
3
3
12.6 13.6 74.4 74 0.4

56.4 57.4 94.4 94 0.5
3
3
1
3
69.4 70.4 107.4 107 0.5

81.4 82.4 118.4 118 0.5
3
3
3
3
OPERATION GUIDANCE
CUTTING CONDITIONS
N047
TECHNICAL DATA
N051,N052
Q001
DRILLING
25
30
3
3
PL
25
30
3
3
35.3 37.3 68.3 68 0.3
2.00
DCON
1.55
10.4 12.3 68.4 68 0.4

22.4 24.4 68.4 68 0.4
LF
20
OAL
1
20
23.3 26.3 55.3 55 0.3
(mm) (l/d)
LH
12
MWS0200SB
MWS0200LB
MWS0200XB
MWS0200X20DB
MWS0200X25DB
MWS0200X30DB
MWS0205SB
MWS0205X20DB
MWS0205X25DB
MWS0205X30DB
MWS0210SB
MWS0210LB
MWS0210XB
MWS0210X20DB
MWS0210X25DB
MWS0210X30DB
MWS0215SB
MWS0215X20DB
MWS0215X25DB
MWS0215X30DB
MWS0220SB
MWS0220LB
MWS0220XB
MWS0220X20DB
MWS0220X25DB
MWS0220X30DB
MWS0225SB
MWS0225X20DB
MWS0225X25DB
MWS0225X30DB
MWS0230SB
MWS0230LB
MWS0230XB
MWS0230X20DB
MWS0230X25DB
MWS0230X30DB
MWS0235SB
MWS0235X20DB
MWS0235X25DB
MWS0235X30DB
MWS0240SB
MWS0240LB
MWS0240XB
MWS0240X20DB
MWS0240X25DB
MWS0240X30DB
MWS0245SB
MWS0245X20DB
MWS0245X25DB
MWS0245X30DB
1
3
Type
LCF
25
30
VP15TF
Hole Depth
20
3
3
PL
1
5
DCON
1.50
7.7 10.5 55.3 55 0.3

17.3 20.3 55.3 55 0.3
LF
12
MWS0150SB
MWS0150LB
MWS0150XB
MWS0150X20DB
MWS0150X25DB
MWS0150X30DB
MWS0155SB
MWS0155X20DB
MWS0155X25DB
MWS0155X30DB
MWS0160SB
MWS0160LB
MWS0160XB
MWS0160X20DB
MWS0160X25DB
MWS0160X30DB
MWS0165SB
MWS0165X20DB
MWS0165X25DB
MWS0165X30DB
MWS0170SB
MWS0170LB
MWS0170XB
MWS0170X20DB
MWS0170X25DB
MWS0170X30DB
MWS0175SB
MWS0175X20DB
MWS0175X25DB
MWS0175X30DB
MWS0180SB
MWS0180LB
MWS0180XB
MWS0180X20DB
MWS0180X25DB
MWS0180X30DB
MWS0185SB
MWS0185X20DB
MWS0185X25DB
MWS0185X30DB
MWS0190SB
MWS0190LB
MWS0190XB
MWS0190X20DB
MWS0190X25DB
MWS0190X30DB
MWS0195SB
MWS0195X20DB
MWS0195X25DB
MWS0195X30DB
OAL
LH
1
5
DC
Dimensions (mm)
Stock
Order Number
Type
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
N035
MWS
WSTAR DRILLS
25
30
1
5
12
2.60
20
25
30
1
20
2.65
25
30
1
5
12
2.70
20
25
30
1
20
2.75
25
30
1
5
12
DRILLING
2.80
20
25
30
1
20
2.85
25
30
1
5
2.90
12
20
25
30
1
20
2.95
25
30
58.5 59.5 94.5 94 0.5
10
70.5 71.5 107.5 107 0.5

83.5 84.5 118.5 118 0.5
3
3
3
3
15
20
13.1 13.1 81.5 81 0.5

59.5 59.5 103.5 103 0.5
3
3
2
4
25
30
71.5 71.5 117.5 117 0.5

84.5 84.5 132.5 132 0.5
3
3
4
4
3
5
13.5 13.5 81.5 81 0.5

33.5 33.5 81.5 81 0.5
3
3
2
4
10
45.5 45.5 81.5 81 0.5
15
60.5 60.5 103.5 103 0.5
20
73.5 73.5 117.5 117 0.5

86.5 86.5 132.5 132 0.5
3
3
4
4
25
30
13.7 13.7 81.5 81 0.5

61.5 61.5 103.5 103 0.5
3
3
2
4
3
5
74.5 74.5 117.5 117 0.5

87.5 87.5 132.5 132 0.5
3
3
4
4
10
13.9 13.9 81.5 81 0.5

33.5 33.5 81.5 81 0.5
3
3
2
4
15
45.5 45.5 81.5 81 0.5
62.5 62.5 103.5 103 0.5
76.5 76.5 117.5 117 0.5

89.5 89.5 132.5 132 0.5
3.00
3.10
3.20
20
a
a
25
30
3
3
4
4
3
5
14.1 14.1 81.5 81 0.5

63.5 63.5 103.5 103 0.5
3
3
2
4
10
77.5 77.5 117.5 117 0.5

91.5 91.5 132.5 132 0.5
3
3
4
4
15
20
14.5 14.5 81.5 81 0.5

33.5 33.5 81.5 81 0.5
3
3
2
4
25
30
45.5 45.5 81.5 81 0.5
64.5 64.5 103.5 103 0.5
3
5
78.5 78.5 117.5 117 0.5

92.5 92.5 132.5 132 0.5
3
3
4
4
10
14.7 14.7 81.5 81 0.5

66.5 66.5 103.5 103 0.5
3
3
2
4
15
20
80.5 80.5 117.5 117 0.5

94.5 94.5 132.5 132 0.5
3
3
4
4
25
30
14.9 14.9 81.5 81 0.5

33.5 33.5 81.5 81 0.5
3
3
2
4
3
5
3.30
3.40
45.5 45.5 81.5 81 0.5
67.5 67.5 103.5 103 0.5
10
81.5 81.5 117.5 117 0.5

96.5 96.5 132.5 132 0.5
3
3
4
4
15
20
15.1 15.1 81.5 81 0.5

68.5 68.5 103.5 103 0.5
3
3
2
4
25
30
83.5 83.5 117.5 117 0.5

97.5 97.5 132.5 132 0.5
3
3
4
4
3.50
N036
DCON
2.55
38.5 39.5 74.5 74 0.5
MWS0300MB
MWS0300LB
MWS0300X8DB
MWS0300X10DB
MWS0300X15DB
MWS0300X20DB
MWS0300X25DB
MWS0300X30DB
MWS0310MB
MWS0310LB
MWS0310X8DB
MWS0310X10DB
MWS0310X15DB
MWS0310X20DB
MWS0310X25DB
MWS0310X30DB
MWS0320MB
MWS0320LB
MWS0320X8DB
MWS0320X10DB
MWS0320X15DB
MWS0320X20DB
MWS0320X25DB
MWS0320X30DB
MWS0330MB
MWS0330LB
MWS0330X8DB
MWS0330X10DB
MWS0330X15DB
MWS0330X20DB
MWS0330X25DB
MWS0330X30DB
MWS0340MB
MWS0340LB
MWS0340X8DB
MWS0340X10DB
MWS0340X15DB
MWS0340X20DB
MWS0340X25DB
MWS0340X30DB
MWS0350MB
MWS0350LB
MWS0350X8DB
MWS0350X10DB
MWS0350X15DB
MWS0350X20DB
MWS0350X25DB
MWS0350X30DB
24.5 24.5 72.5 72 0.5

33.5 33.5 81.5 81 0.5
3
3
5
5
35.5 35.5 81.5 81 0.5
39.5 42.5 90.5 90 0.5
54.5 57.5 105.5 105 0.5
69.5 72.5 120.5 120 0.5
84.5 87.5 135.5 135 0.5

99.5 102.5 150.5 150 0.5
3
3
6
6
28.6 28.6 76.6 76 0.6

39.6 39.6 87.6 87 0.6
4
4
5
5
41.6 41.6 87.6 87 0.6
46.6 49.6 97.6 97 0.6
63.6 66.6 114.6 114 0.6
PL
LF
1
20
3
5
(mm) (l/d)
OAL
1
3
Type
LH
25
30
VP15TF
Hole Depth
20
3
3
PL
DCON
2.50
12.9 13.8 74.5 74 0.4

28.5 29.5 74.5 74 0.5
LF
12
MWS0250SB
MWS0250LB
MWS0250XB
MWS0250X20DB
MWS0250X25DB
MWS0250X30DB
MWS0255SB
MWS0255X20DB
MWS0255X25DB
MWS0255X30DB
MWS0260SB
MWS0260LB
MWS0260XB
MWS0260X20DB
MWS0260X25DB
MWS0260X30DB
MWS0265SB
MWS0265X20DB
MWS0265X25DB
MWS0265X30DB
MWS0270SB
MWS0270LB
MWS0270XB
MWS0270X20DB
MWS0270X25DB
MWS0270X30DB
MWS0275SB
MWS0275X20DB
MWS0275X25DB
MWS0275X30DB
MWS0280SB
MWS0280LB
MWS0280XB
MWS0280X20DB
MWS0280X25DB
MWS0280X30DB
MWS0285SB
MWS0285X20DB
MWS0285X25DB
MWS0285X30DB
MWS0290SB
MWS0290LB
MWS0290XB
MWS0290X20DB
MWS0290X25DB
MWS0290X30DB
MWS0295SB
MWS0295X20DB
MWS0295X25DB
MWS0295X30DB
OAL
Order Number
LH
1
5
DC
Dimensions (mm)
Stock
Type
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
81.6 84.6 132.6 132 0.6
98.6 101.6 149.6 149 0.6

116.6 119.6 167.6 167 0.6
4
4
6
6
28.6 28.6 76.6 76 0.6

39.6 39.6 87.6 87 0.6
4
4
5
5
41.6 41.6 87.6 87 0.6
46.6 49.6 97.6 97 0.6
63.6 66.6 114.6 114 0.6
81.6 84.6 132.6 132 0.6
98.6 101.6 149.6 149 0.6

116.6 119.6 167.6 167 0.6
4
4
6
6
28.6 28.6 76.6 76 0.6

39.6 39.6 87.6 87 0.6
4
4
5
5
41.6 41.6 87.6 87 0.6
46.6 49.6 97.6 97 0.6
63.6 66.6 114.6 114 0.6
81.6 84.6 132.6 132 0.6
98.6 101.6 149.6 149 0.6

116.6 119.6 167.6 167 0.6
4
4
6
6
28.6 28.6 76.6 76 0.6

39.6 39.6 87.6 87 0.6
4
4
5
5
41.6 41.6 87.6 87 0.6
46.6 49.6 97.6 97 0.6
63.6 66.6 114.6 114 0.6
81.6 84.6 132.6 132 0.6
98.6 101.6 149.6 149 0.6

116.6 119.6 167.6 167 0.6
4
4
6
6
28.6 28.6 76.6 76 0.6

39.6 39.6 87.6 87 0.6
4
4
5
5
41.6 41.6 87.6 87 0.6
46.6 49.6 97.6 97 0.6
63.6 66.6 114.6 114 0.6
81.6 84.6 132.6 132 0.6
98.6 101.6 149.6 149 0.6

116.6 119.6 167.6 167 0.6
4
4
6
6
CARBIDE
3.7
3.8
3.9
4.0
4.1
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
a
a
52.7 55.7 103.7 103 0.7
10
72.7 75.7 123.7 123 0.7
15
4.2
92.7 95.7 143.7 143 0.7
20
112.7 115.7 163.7 163 0.7

132.7 135.7 183.7 183 0.7
4
4
6
6
25
30
32.7 32.7 80.7 80 0.7

44.7 44.7 92.7 92 0.7
4
4
5
5
3
5
46.7 46.7 92.7 92 0.7
52.7 55.7 103.7 103 0.7
10
72.7 75.7 123.7 123 0.7
15
92.7 95.7 143.7 143 0.7
20
112.7 115.7 163.7 163 0.7

132.7 135.7 183.7 183 0.7
4
4
6
6
25
30
32.7 32.7 80.7 80 0.7

44.7 44.7 92.7 92 0.7
4
4
5
5
3
5
46.7 46.7 92.7 92 0.7
52.7 55.7 103.7 103 0.7
10
72.7 75.7 123.7 123 0.7
15
4.3
4.4
92.7 95.7 143.7 143 0.7
20
112.7 115.7 163.7 163 0.7

132.7 135.7 183.7 183 0.7
4
4
6
6
25
30
32.7 32.7 80.7 80 0.7

44.7 44.7 92.7 92 0.7
4
4
5
5
3
5
46.7 46.7 92.7 92 0.7
52.7 55.7 103.7 103 0.7
10
72.7 75.7 123.7 123 0.7
15
92.7 95.7 143.7 143 0.7
20
112.7 115.7 163.7 163 0.7

132.7 135.7 183.7 183 0.7
4
4
6
6
25
30
32.7 32.7 80.7 80 0.7

44.7 44.7 92.7 92 0.7
4
4
5
5
3
5
46.7 46.7 92.7 92 0.7
52.7 55.7 103.7 103 0.7
10
72.7 75.7 123.7 123 0.7
15
92.7 95.7 143.7 143 0.7
20
112.7 115.7 163.7 163 0.7

132.7 135.7 183.7 183 0.7
4
4
6
6
25
30
36.7 36.7 86.7 86 0.7

50.7 50.7 100.7 100 0.7
5
5
5
5
3
5
52.7 52.7 100.7 100 0.7
59.7 62.7 112.7 112 0.7
10
81.7 84.7 134.7 134 0.7
15
104.7 107.7 157.7 157 0.7
20
126.7 129.7 179.7 179 0.7

149.7 152.7 202.7 202 0.7
5
5
6
6
25
30
4.5
4.6
4.7
5
5
5
5
52.8 52.8 100.8 100 0.8
59.8 62.8 112.8 112 0.8
81.8 84.8 134.8 134 0.8
104.8 107.8 157.8 157 0.8
126.8 129.8 179.8 179 0.8

149.8 152.8 202.8 202 0.8
5
5
6
6
36.8 36.8 86.8 86 0.8

50.8 50.8 100.8 100 0.8
5
5
5
5
52.8 52.8 100.8 100 0.8
59.8 62.8 112.8 112 0.8
81.8 84.8 134.8 134 0.8
104.8 107.8 157.8 157 0.8
126.8 129.8 179.8 179 0.8

149.8 152.8 202.8 202 0.8
5
5
6
6
36.8 36.8 86.8 86 0.8

50.8 50.8 100.8 100 0.8
5
5
5
5
52.8 52.8 100.8 100 0.8
59.8 62.8 112.8 112 0.8
81.8 84.8 134.8 134 0.8
104.8 107.8 157.8 157 0.8
126.8 129.8 179.8 179 0.8

149.8 152.8 202.8 202 0.8
5
5
6
6
36.8 36.8 86.8 86 0.8

50.8 50.8 100.8 100 0.8
5
5
5
5
52.8 52.8 100.8 100 0.8
59.8 62.8 112.8 112 0.8
81.8 84.8 134.8 134 0.8
104.8 107.8 157.8 157 0.8
126.8 129.8 179.8 179 0.8

149.8 152.8 202.8 202 0.8
5
5
6
6
40.8 40.8 90.8 90 0.8

55.8 55.8 105.8 105 0.8
5
5
5
5
57.8 57.8 105.8 105 0.8
65.8 68.8 118.8 118 0.8
90.8 93.8 143.8 143 0.8
115.8 118.8 168.8 168 0.8
140.8 143.8 193.8 193 0.8

165.8 168.8 218.8 218 0.8
5
5
6
6
40.9 40.9 90.9 90 0.9

55.9 55.9 105.9 105 0.9
5
5
5
5
57.9 57.9 105.9 105 0.9
65.9 68.9 118.9 118 0.9
90.9 93.9 143.9 143 0.9
115.9 118.9 168.9 168 0.9
140.9 143.9 193.9 193 0.9

165.9 168.9 218.9 218 0.9
5
5
6
6
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N047
N051,N052
Q001
DRILLING
DCON
3
5
36.8 36.8 86.8 86 0.8

50.8 50.8 100.8 100 0.8
PL
46.7 46.7 92.7 92 0.7
MWS0420MB
MWS0420LB
MWS0420X8DB
MWS0420X10DB
MWS0420X15DB
MWS0420X20DB
MWS0420X25DB
MWS0420X30DB
MWS0430MB
MWS0430LB
MWS0430X8DB
MWS0430X10DB
MWS0430X15DB
MWS0430X20DB
MWS0430X25DB
MWS0430X30DB
MWS0440MB
MWS0440LB
MWS0440X8DB
MWS0440X10DB
MWS0440X15DB
MWS0440X20DB
MWS0440X25DB
MWS0440X30DB
MWS0450MB
MWS0450LB
MWS0450X8DB
MWS0450X10DB
MWS0450X15DB
MWS0450X20DB
MWS0450X25DB
MWS0450X30DB
MWS0460MB
MWS0460LB
MWS0460X8DB
MWS0460X10DB
MWS0460X15DB
MWS0460X20DB
MWS0460X25DB
MWS0460X30DB
MWS0470MB
MWS0470LB
MWS0470X8DB
MWS0470X10DB
MWS0470X15DB
MWS0470X20DB
MWS0470X25DB
MWS0470X30DB
LF
25
30
OAL
20
3
5
(mm) (l/d)
LH
5
5
Type
LCF
15
VP15TF
3.6
Hole Depth
DCON
10
4
4
PL
32.7 32.7 80.7 80 0.7

44.7 44.7 92.7 92 0.7
LF
MWS0360MB
MWS0360LB
MWS0360X8DB
MWS0360X10DB
MWS0360X15DB
MWS0360X20DB
MWS0360X25DB
MWS0360X30DB
MWS0370MB
MWS0370LB
MWS0370X8DB
MWS0370X10DB
MWS0370X15DB
MWS0370X20DB
MWS0370X25DB
MWS0370X30DB
MWS0380MB
MWS0380LB
MWS0380X8DB
MWS0380X10DB
MWS0380X15DB
MWS0380X20DB
MWS0380X25DB
MWS0380X30DB
MWS0390MB
MWS0390LB
MWS0390X8DB
MWS0390X10DB
MWS0390X15DB
MWS0390X20DB
MWS0390X25DB
MWS0390X30DB
MWS0400MB
MWS0400LB
MWS0400X8DB
MWS0400X10DB
MWS0400X15DB
MWS0400X20DB
MWS0400X25DB
MWS0400X30DB
MWS0410MB
MWS0410LB
MWS0410X8DB
MWS0410X10DB
MWS0410X15DB
MWS0410X20DB
MWS0410X25DB
MWS0410X30DB
OAL
Order Number
LH
3
5
DC
Dimensions (mm)
Stock
Type
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
N037
MWS
WSTAR DRILLS
3
5
4.9
5.0
5.1
DRILLING
5.2
5.3
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
a
a
65.9 68.9 118.9 118 0.9
10
90.9 93.9 143.9 143 0.9
15
115.9 118.9 168.9 168 0.9
20
140.9 143.9 193.9 193 0.9

165.9 168.9 218.9 218 0.9
5
5
6
6
25
30
40.9 40.9 90.9 90 0.9

55.9 55.9 105.9 105 0.9
5
5
5
5
3
5
57.9 57.9 105.9 105 0.9
65.9 68.9 118.9 118 0.9
10
90.9 93.9 143.9 143 0.9
15
5.4
5.5
115.9 118.9 168.9 168 0.9
20
140.9 143.9 193.9 193 0.9

165.9 168.9 218.9 218 0.9
5
5
6
6
25
30
28.4 30.9 82.9 82 0.9

44.9 48.9 100.9 100 0.9
6
6
5
5
3
5
57.9 57.9 105.9 105 0.9
65.9 68.9 118.9 118 0.9
10
90.9 93.9 143.9 143 0.9
15
115.9 118.9 168.9 168 0.9
20
140.9 143.9 193.9 193 0.9

165.9 168.9 218.9 218 0.9
5
5
6
6
25
30
28.4 30.9 82.9 82 0.9

44.9 48.9 100.9 100 0.9
6
6
5
5
3
5
5.6
61.9 66.9 118.9 118 0.9
72.9 75.9 127.9 127 0.9
10
99.9 102.9 154.9 154 0.9
15
127.9 130.9 182.9 182 0.9
20
154.9 157.9 209.9 209 0.9

182.9 185.9 237.9 237 0.9
6
6
6
6
25
30
28.4 30.9 82.9 82 0.9

44.9 48.9 100.9 100 0.9
6
6
5
5
3
5
61.9 66.9 118.9 118 0.9
72.9 75.9 127.9 127 0.9
10
99.9 102.9 154.9 154 0.9
15
127.9 130.9 182.9 182 0.9
20
154.9 157.9 209.9 209 0.9

182.9 185.9 237.9 237 0.9
6
6
6
6
25
30
28.5 31.0 83.0 82 1.0

45.0 49.0 101.0 100 1.0
6
6
5
5
3
5
5.7
5.8
62.0 67.0 119.0 118 1.0
73.0 76.0 128.0 127 1.0
10
100.0 103.0 155.0 154 1.0
15
128.0 131.0 183.0 182 1.0
20
155.0 158.0 210.0 209 1.0

183.0 186.0 238.0 237 1.0
6
6
6
6
25
30
5.9
N038
28.5 31.0 83.0 82 1.0

45.0 49.0 101.0 100 1.0
DCON
25
30
57.9 57.9 105.9 105 0.9
MWS0540MB
MWS0540LB
MWS0540X8DB
MWS0540X10DB
MWS0540X15DB
MWS0540X20DB
MWS0540X25DB
MWS0540X30DB
MWS0550MB
MWS0550LB
MWS0550X8DB
MWS0550X10DB
MWS0550X15DB
MWS0550X20DB
MWS0550X25DB
MWS0550X30DB
MWS0560MB
MWS0560LB
MWS0560X8DB
MWS0560X10DB
MWS0560X15DB
MWS0560X20DB
MWS0560X25DB
MWS0560X30DB
MWS0570MB
MWS0570LB
MWS0570X8DB
MWS0570X10DB
MWS0570X15DB
MWS0570X20DB
MWS0570X25DB
MWS0570X30DB
MWS0580MB
MWS0580LB
MWS0580X8DB
MWS0580X10DB
MWS0580X15DB
MWS0580X20DB
MWS0580X25DB
MWS0580X30DB
MWS0590MB
MWS0590LB
MWS0590X8DB
MWS0590X10DB
MWS0590X15DB
MWS0590X20DB
MWS0590X25DB
MWS0590X30DB
PL
LF
20
3
5
(mm) (l/d)
OAL
5
5
LH
15
VP15TF
4.8
Hole Depth
DCON
10
5
5
PL
40.9 40.9 90.9 90 0.9

55.9 55.9 105.9 105 0.9
LF
MWS0480MB
MWS0480LB
MWS0480X8DB
MWS0480X10DB
MWS0480X15DB
MWS0480X20DB
MWS0480X25DB
MWS0480X30DB
MWS0490MB
MWS0490LB
MWS0490X8DB
MWS0490X10DB
MWS0490X15DB
MWS0490X20DB
MWS0490X25DB
MWS0490X30DB
MWS0500MB
MWS0500LB
MWS0500X8DB
MWS0500X10DB
MWS0500X15DB
MWS0500X20DB
MWS0500X25DB
MWS0500X30DB
MWS0510MB
MWS0510LB
MWS0510X8DB
MWS0510X10DB
MWS0510X15DB
MWS0510X20DB
MWS0510X25DB
MWS0510X30DB
MWS0520MB
MWS0520LB
MWS0520X8DB
MWS0520X10DB
MWS0520X15DB
MWS0520X20DB
MWS0520X25DB
MWS0520X30DB
MWS0530MB
MWS0530LB
MWS0530X8DB
MWS0530X10DB
MWS0530X15DB
MWS0530X20DB
MWS0530X25DB
MWS0530X30DB
OAL
Order Number
LH
3
5
DC
Dimensions (mm)
Stock
Type
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
Type
6
6
5
5
62.0 67.0 119.0 118 1.0
73.0 76.0 128.0 127 1.0
100.0 103.0 155.0 154 1.0
128.0 131.0 183.0 182 1.0
155.0 158.0 210.0 209 1.0

183.0 186.0 238.0 237 1.0
6
6
6
6
28.5 31.0 83.0 82 1.0

45.0 49.0 101.0 100 1.0
6
6
5
5
62.0 67.0 119.0 118 1.0
73.0 76.0 128.0 127 1.0
100.0 103.0 155.0 154 1.0
128.0 131.0 183.0 182 1.0
155.0 158.0 210.0 209 1.0

183.0 186.0 238.0 237 1.0
6
6
6
6
31.0 31.0 83.0 82 1.0

49.0 49.0 101.0 100 1.0
6
6
5
5
67.0 67.0 119.0 118 1.0
79.0 82.0 134.0 133 1.0
109.0 112.0 164.0 163 1.0
139.0 142.0 194.0 193 1.0
169.0 172.0 224.0 223 1.0

199.0 202.0 254.0 253 1.0
6
6
6
6
31.0 31.0 83.0 82 1.0

49.0 49.0 101.0 100 1.0
6
6
5
5
67.0 67.0 119.0 118 1.0
79.0 82.0 134.0 133 1.0
109.0 112.0 164.0 163 1.0
139.0 142.0 194.0 193 1.0
169.0 172.0 224.0 223 1.0

199.0 202.0 254.0 253 1.0
6
6
6
6
31.1 31.1 83.1 82 1.1

49.1 49.1 101.1 100 1.1
6
6
5
5
67.1 67.1 119.1 118 1.1
79.1 82.1 134.1 133 1.1
109.1 112.1 164.1 163 1.1
139.1 142.1 194.1 193 1.1
169.1 172.1 224.1 223 1.1

199.1 202.1 254.1 253 1.1
6
6
6
6
31.1 31.1 83.1 82 1.1

49.1 49.1 101.1 100 1.1
6
6
5
5
67.1 67.1 119.1 118 1.1
79.1 82.1 134.1 133 1.1
109.1 112.1 164.1 163 1.1
139.1 142.1 194.1 193 1.1
169.1 172.1 224.1 223 1.1

199.1 202.1 254.1 253 1.1
6
6
6
6
CARBIDE
6.1
6.2
6.3
6.4
6.5
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
a
a
79.1 82.1 134.1 133 1.1
10
109.1 112.1 164.1 163 1.1
15
139.1 142.1 194.1 193 1.1
20
169.1 172.1 224.1 223 1.1

199.1 202.1 254.1 253 1.1
6
6
6
6
25
30
33.6 36.1 89.1 88 1.1

53.1 57.1 110.1 109 1.1
7
7
5
5
3
5
73.1 78.1 131.1 130 1.1
86.1 89.1 142.1 141 1.1
10
118.1 121.1 174.1 173 1.1
15
151.1 154.1 207.1 206 1.1
20
183.1 186.1 239.1 238 1.1

216.1 219.1 272.1 271 1.1
7
7
6
6
25
30
33.6 36.1 89.1 88 1.1

53.1 57.1 110.1 109 1.1
7
7
5
5
3
5
73.1 78.1 131.1 130 1.1
86.1 89.1 142.1 141 1.1
10
118.1 121.1 174.1 173 1.1
15
151.1 154.1 207.1 206 1.1
20
183.1 186.1 239.1 238 1.1

216.1 219.1 272.1 271 1.1
7
7
6
6
25
30
33.6 36.1 89.1 88 1.1

53.1 57.1 110.1 109 1.1
7
7
5
5
3
5
73.1 78.1 131.1 130 1.1
86.1 89.1 142.1 141 1.1
10
118.1 121.1 174.1 173 1.1
15
151.1 154.1 207.1 206 1.1
20
183.1 186.1 239.1 238 1.1

216.1 219.1 272.1 271 1.1
7
7
6
6
25
30
33.7 36.2 89.2 88 1.2

53.2 57.2 110.2 109 1.2
7
7
5
5
3
5
73.2 78.2 131.2 130 1.2
86.2 89.2 142.2 141 1.2
10
118.2 121.2 174.2 173 1.2
15
151.2 154.2 207.2 206 1.2
20
183.2 186.2 239.2 238 1.2

216.2 219.2 272.2 271 1.2
7
7
6
6
25
30
33.7 36.2 89.2 88 1.2

53.2 57.2 110.2 109 1.2
7
7
5
5
3
5
73.2 78.2 131.2 130 1.2
86.2 89.2 142.2 141 1.2
10
118.2 121.2 174.2 173 1.2
15
151.2 154.2 207.2 206 1.2
20
183.2 186.2 239.2 238 1.2

216.2 219.2 272.2 271 1.2
7
7
6
6
25
30
6.6
6.7
6.8
6.9
7.0
7.1
Type
7
7
5
5
78.2 78.2 131.2 130 1.2
92.2 95.2 148.2 147 1.2
127.2 130.2 183.2 182 1.2
162.2 165.2 218.2 217 1.2
197.2 200.2 253.2 252 1.2

232.2 235.2 288.2 287 1.2
7
7
6
6
36.2 36.2 89.2 88 1.2

57.2 57.2 110.2 109 1.2
7
7
5
5
78.2 78.2 131.2 130 1.2
92.2 95.2 148.2 147 1.2
127.2 130.2 183.2 182 1.2
162.2 165.2 218.2 217 1.2
197.2 200.2 253.2 252 1.2

232.2 235.2 288.2 287 1.2
7
7
6
6
36.2 36.2 89.2 88 1.2

57.2 57.2 110.2 109 1.2
7
7
5
5
78.2 78.2 131.2 130 1.2
92.2 95.2 148.2 147 1.2
127.2 130.2 183.2 182 1.2
162.2 165.2 218.2 217 1.2
197.2 200.2 253.2 252 1.2

232.2 235.2 288.2 287 1.2
7
7
6
6
36.3 36.3 89.3 88 1.3

57.3 57.3 110.3 109 1.3
7
7
5
5
78.3 78.3 131.3 130 1.3
92.3 95.3 148.3 147 1.3
127.3 130.3 183.3 182 1.3
162.3 165.3 218.3 217 1.3
197.3 200.3 253.3 252 1.3

232.3 235.3 288.3 287 1.3
7
7
6
6
36.3 36.3 89.3 88 1.3

57.3 57.3 110.3 109 1.3
7
7
5
5
78.3 78.3 131.3 130 1.3
92.3 95.3 148.3 147 1.3
127.3 130.3 183.3 182 1.3
162.3 165.3 218.3 217 1.3
197.3 200.3 253.3 252 1.3

232.3 235.3 288.3 287 1.3
7
7
6
6
38.8 41.3 95.3 94 1.3

61.3 65.3 119.3 118 1.3
8
8
5
5
84.3 89.3 143.3 142 1.3
99.3 102.3 156.3 155 1.3
136.3 139.3 193.3 192 1.3
174.3 177.3 231.3 230 1.3
211.3 214.3 268.3 267 1.3

249.3 252.3 306.3 305 1.3
8
8
6
6
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N047
N051,N052
Q001
DRILLING
3
5
36.2 36.2 89.2 88 1.2

57.2 57.2 110.2 109 1.2
DCON
PL
25
30
67.1 67.1 119.1 118 1.1
MWS0660MB
MWS0660LB
MWS0660X8DB
MWS0660X10DB
MWS0660X15DB
MWS0660X20DB
MWS0660X25DB
MWS0660X30DB
MWS0670MB
MWS0670LB
MWS0670X8DB
MWS0670X10DB
MWS0670X15DB
MWS0670X20DB
MWS0670X25DB
MWS0670X30DB
MWS0680MB
MWS0680LB
MWS0680X8DB
MWS0680X10DB
MWS0680X15DB
MWS0680X20DB
MWS0680X25DB
MWS0680X30DB
MWS0690MB
MWS0690LB
MWS0690X8DB
MWS0690X10DB
MWS0690X15DB
MWS0690X20DB
MWS0690X25DB
MWS0690X30DB
MWS0700MB
MWS0700LB
MWS0700X8DB
MWS0700X10DB
MWS0700X15DB
MWS0700X20DB
MWS0700X25DB
MWS0700X30DB
MWS0710MB
MWS0710LB
MWS0710X8DB
MWS0710X10DB
MWS0710X15DB
MWS0710X20DB
MWS0710X25DB
MWS0710X30DB
LF
OAL
20
3
5
(mm) (l/d)
LH
5
5
LCF
15
VP15TF
6.0
Hole Depth
DCON
10
6
6
PL
31.1 31.1 83.1 82 1.1

49.1 49.1 101.1 100 1.1
LF
MWS0600MB
MWS0600LB
MWS0600X8DB
MWS0600X10DB
MWS0600X15DB
MWS0600X20DB
MWS0600X25DB
MWS0600X30DB
MWS0610MB
MWS0610LB
MWS0610X8DB
MWS0610X10DB
MWS0610X15DB
MWS0610X20DB
MWS0610X25DB
MWS0610X30DB
MWS0620MB
MWS0620LB
MWS0620X8DB
MWS0620X10DB
MWS0620X15DB
MWS0620X20DB
MWS0620X25DB
MWS0620X30DB
MWS0630MB
MWS0630LB
MWS0630X8DB
MWS0630X10DB
MWS0630X15DB
MWS0630X20DB
MWS0630X25DB
MWS0630X30DB
MWS0640MB
MWS0640LB
MWS0640X8DB
MWS0640X10DB
MWS0640X15DB
MWS0640X20DB
MWS0640X25DB
MWS0640X30DB
MWS0650MB
MWS0650LB
MWS0650X8DB
MWS0650X10DB
MWS0650X15DB
MWS0650X20DB
MWS0650X25DB
MWS0650X30DB
OAL
Order Number
LH
3
5
DC
Dimensions (mm)
Stock
Type
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
N039
MWS
WSTAR DRILLS
3
5
7.3
7.4
7.5
DRILLING
7.6
7.7
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
a
a
99.3 102.3 156.3 155 1.3
10
136.3 139.3 193.3 192 1.3
15
174.3 177.3 231.3 230 1.3
20
211.3 214.3 268.3 267 1.3

249.3 252.3 306.3 305 1.3
8
8
6
6
25
30
38.8 41.3 95.3 94 1.3

61.3 65.3 119.3 118 1.3
8
8
5
5
3
5
7.8
84.3 89.3 143.3 142 1.3
99.3 102.3 156.3 155 1.3
10
136.3 139.3 193.3 192 1.3
15
174.3 177.3 231.3 230 1.3
20
211.3 214.3 268.3 267 1.3

249.3 252.3 306.3 305 1.3
8
8
6
6
25
30
38.8 41.3 95.3 94 1.3

61.3 65.3 119.3 118 1.3
8
8
5
5
3
5
84.3 89.3 143.3 142 1.3
99.3 102.3 156.3 155 1.3
10
136.3 139.3 193.3 192 1.3
15
174.3 177.3 231.3 230 1.3
20
211.3 214.3 268.3 267 1.3

249.3 252.3 306.3 305 1.3
8
8
6
6
25
30
38.9 41.4 95.4 94 1.4

61.4 65.4 119.4 118 1.4
8
8
5
5
3
5
7.9
8.0
84.4 89.4 143.4 142 1.4
99.4 102.4 156.4 155 1.4
10
136.4 139.4 193.4 192 1.4
15
174.4 177.4 231.4 230 1.4
20
211.4 214.4 268.4 267 1.4

249.4 252.4 306.4 305 1.4
8
8
6
6
25
30
41.4 41.4 95.4 94 1.4

65.4 65.4 119.4 118 1.4
8
8
5
5
3
5
89.4 89.4 143.4 142 1.4
105.4 108.4 162.4 161 1.4
10
145.4 148.4 202.4 201 1.4
15
185.4 188.4 242.4 241 1.4
20
225.4 228.4 282.4 281 1.4

265.4 268.4 322.4 321 1.4
8
8
6
6
25
30
41.4 41.4 95.4 94 1.4

65.4 65.4 119.4 118 1.4
8
8
5
5
3
5
8.1
8.2
89.4 89.4 143.4 142 1.4
105.4 108.4 162.4 161 1.4
10
145.4 148.4 202.4 201 1.4
15
185.4 188.4 242.4 241 1.4
20
225.4 228.4 282.4 281 1.4

265.4 268.4 322.4 321 1.4
8
8
6
6
25
30
8.3
N040
41.4 41.4 95.4 94 1.4

65.4 65.4 119.4 118 1.4
DCON
25
30
84.3 89.3 143.3 142 1.3
MWS0780MB
MWS0780LB
MWS0780X8DB
MWS0780X10DB
MWS0780X15DB
MWS0780X20DB
MWS0780X25DB
MWS0780X30DB
MWS0790MB
MWS0790LB
MWS0790X8DB
MWS0790X10DB
MWS0790X15DB
MWS0790X20DB
MWS0790X25DB
MWS0790X30DB
MWS0800MB
MWS0800LB
MWS0800X8DB
MWS0800X10DB
MWS0800X15DB
MWS0800X20DB
MWS0800X25DB
MWS0800X30DB
MWS0810MB
MWS0810LB
MWS0810X8DB
MWS0810X10DB
MWS0810X15DB
MWS0810X20DB
MWS0810X25DB
MWS0810X30DB
MWS0820MB
MWS0820LB
MWS0820X8DB
MWS0820X10DB
MWS0820X15DB
MWS0820X20DB
MWS0820X25DB
MWS0820X30DB
MWS0830MB
MWS0830LB
MWS0830X8DB
MWS0830X10DB
MWS0830X15DB
MWS0830X20DB
MWS0830X25DB
MWS0830X30DB
PL
LF
20
3
5
(mm) (l/d)
OAL
5
5
LH
15
VP15TF
7.2
Hole Depth
DCON
10
8
8
PL
38.8 41.3 95.3 94 1.3

61.3 65.3 119.3 118 1.3
LF
MWS0720MB
MWS0720LB
MWS0720X8DB
MWS0720X10DB
MWS0720X15DB
MWS0720X20DB
MWS0720X25DB
MWS0720X30DB
MWS0730MB
MWS0730LB
MWS0730X8DB
MWS0730X10DB
MWS0730X15DB
MWS0730X20DB
MWS0730X25DB
MWS0730X30DB
MWS0740MB
MWS0740LB
MWS0740X8DB
MWS0740X10DB
MWS0740X15DB
MWS0740X20DB
MWS0740X25DB
MWS0740X30DB
MWS0750MB
MWS0750LB
MWS0750X8DB
MWS0750X10DB
MWS0750X15DB
MWS0750X20DB
MWS0750X25DB
MWS0750X30DB
MWS0760MB
MWS0760LB
MWS0760X8DB
MWS0760X10DB
MWS0760X15DB
MWS0760X20DB
MWS0760X25DB
MWS0760X30DB
MWS0770MB
MWS0770LB
MWS0770X8DB
MWS0770X10DB
MWS0770X15DB
MWS0770X20DB
MWS0770X25DB
MWS0770X30DB
OAL
Order Number
LH
3
5
DC
Dimensions (mm)
Stock
Type
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
Type
8
8
5
5
89.4 89.4 143.4 142 1.4
105.4 108.4 162.4 161 1.4
145.4 148.4 202.4 201 1.4
185.4 188.4 242.4 241 1.4
225.4 228.4 282.4 281 1.4

265.4 268.4 322.4 321 1.4
8
8
6
6
41.4 41.4 95.4 94 1.4

65.4 65.4 119.4 118 1.4
8
8
5
5
89.4 89.4 143.4 142 1.4
105.4 108.4 162.4 161 1.4
145.4 148.4 202.4 201 1.4
185.4 188.4 242.4 241 1.4
225.4 228.4 282.4 281 1.4

265.4 268.4 322.4 321 1.4
8
8
6
6
41.5 41.5 95.5 94 1.5

65.5 65.5 119.5 118 1.5
8
8
5
5
89.5 89.5 143.5 142 1.5
105.5 108.5 162.5 161 1.5
145.5 148.5 202.5 201 1.5
185.5 188.5 242.5 241 1.5
225.5 228.5 282.5 281 1.5

265.5 268.5 322.5 321 1.5
8
8
6
6
44.0 46.5 101.5 100 1.5

69.5 73.5 128.5 127 1.5
9
9
5
5
95.5 100.5 155.5 154 1.5
112.5 115.5 170.5 169 1.5
154.5 157.5 212.5 211 1.5
197.5 200.5 255.5 254 1.5
239.5 242.5 297.5 296 1.5

282.5 285.5 340.5 339 1.5
9
9
6
6
44.0 46.5 101.5 100 1.5

69.5 73.5 128.5 127 1.5
9
9
5
5
95.5 100.5 155.5 154 1.5
112.5 115.5 170.5 169 1.5
154.5 157.5 212.5 211 1.5
197.5 200.5 255.5 254 1.5
239.5 242.5 297.5 296 1.5

282.5 285.5 340.5 339 1.5
9
9
6
6
44.0 46.5 101.5 100 1.5

69.5 73.5 128.5 127 1.5
9
9
5
5
95.5 100.5 155.5 154 1.5
112.5 115.5 170.5 169 1.5
154.5 157.5 212.5 211 1.5
197.5 200.5 255.5 254 1.5
239.5 242.5 297.5 296 1.5

282.5 285.5 340.5 339 1.5
9
9
6
6
CARBIDE
8.5
8.6
8.7
8.8
8.9
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
3
5
10
15
20
25
30
a
a
112.5 115.5 170.5 169 1.5
10
154.5 157.5 212.5 211 1.5
15
197.5 200.5 255.5 254 1.5
20
239.5 242.5 297.5 296 1.5

282.5 285.5 340.5 339 1.5
9
9
6
6
25
30
44.0 46.5 101.5 100 1.5

69.5 73.5 128.5 127 1.5
9
9
5
5
3
5
9.0
95.5 100.5 155.5 154 1.5
112.5 115.5 170.5 169 1.5
10
154.5 157.5 212.5 211 1.5
15
197.5 200.5 255.5 254 1.5
20
239.5 242.5 297.5 296 1.5

282.5 285.5 340.5 339 1.5
9
9
6
6
25
30
46.6 46.6 101.6 100 1.6

73.6 73.6 128.6 127 1.6
9
9
5
5
3
5
100.6 100.6 155.6 154 1.6
118.6 121.6 176.6 175 1.6
10
163.6 166.6 221.6 220 1.6
15
208.6 211.6 266.6 265 1.6
20
253.6 256.6 311.6 310 1.6

298.6 301.6 356.6 355 1.6
9
9
6
6
25
30
46.6 46.6 101.6 100 1.6

73.6 73.6 128.6 127 1.6
9
9
5
5
3
5
100.6 100.6 155.6 154 1.6
118.6 121.6 176.6 175 1.6
10
163.6 166.6 221.6 220 1.6
15
208.6 211.6 266.6 265 1.6
20
253.6 256.6 311.6 310 1.6

298.6 301.6 356.6 355 1.6
9
9
6
6
25
30
46.6 46.6 101.6 100 1.6

73.6 73.6 128.6 127 1.6
9
9
5
5
3
5
100.6 100.6 155.6 154 1.6
118.6 121.6 176.6 175 1.6
10
163.6 166.6 221.6 220 1.6
15
208.6 211.6 266.6 265 1.6
20
253.6 256.6 311.6 310 1.6

298.6 301.6 356.6 355 1.6
9
9
6
6
25
30
46.6 46.6 101.6 100 1.6

73.6 73.6 128.6 127 1.6
9
9
5
5
3
5
100.6 100.6 155.6 154 1.6
118.6 121.6 176.6 175 1.6
10
163.6 166.6 221.6 220 1.6
15
208.6 211.6 266.6 265 1.6
20
253.6 256.6 311.6 310 1.6

298.6 301.6 356.6 355 1.6
9
9
6
6
25
30
9.1
9.2
9.3
9.4
9.5
46.6 46.6 101.6 100 1.6

73.6 73.6 128.6 127 1.6
9
9
5
5
100.6 100.6 155.6 154 1.6
118.6 121.6 176.6 175 1.6
163.6 166.6 221.6 220 1.6
208.6 211.6 266.6 265 1.6
253.6 256.6 311.6 310 1.6

298.6 301.6 356.6 355 1.6
9
9
6
6
49.2 51.7 107.7 106 1.7 10

77.7 81.7 137.7 136 1.7 10
5
5
106.7 111.7 167.7 166 1.7 10
125.7 128.7 183.7 182 1.7 10
172.7 175.7 230.7 229 1.7 10
220.7 223.7 278.7 277 1.7 10
267.7 270.7 325.7 324 1.7 10

315.7 318.7 373.7 372 1.7 10
6
6
49.2 51.7 107.7 106 1.7 10

77.7 81.7 137.7 136 1.7 10
5
5
106.7 111.7 167.7 166 1.7 10
125.7 128.7 183.7 182 1.7 10
172.7 175.7 230.7 229 1.7 10
220.7 223.7 278.7 277 1.7 10
267.7 270.7 325.7 324 1.7 10

315.7 318.7 373.7 372 1.7 10
6
6
49.2 51.7 107.7 106 1.7 10

77.7 81.7 137.7 136 1.7 10
5
5
106.7 111.7 167.7 166 1.7 10
125.7 128.7 183.7 182 1.7 10
172.7 175.7 230.7 229 1.7 10
220.7 223.7 278.7 277 1.7 10
267.7 270.7 325.7 324 1.7 10

315.7 318.7 373.7 372 1.7 10
6
6
49.2 51.7 107.7 106 1.7 10

77.7 81.7 137.7 136 1.7 10
5
5
106.7 111.7 167.7 166 1.7 10
125.7 128.7 183.7 182 1.7 10
172.7 175.7 230.7 229 1.7 10
220.7 223.7 278.7 277 1.7 10
267.7 270.7 325.7 324 1.7 10

315.7 318.7 373.7 372 1.7 10
6
6
49.2 51.7 107.7 106 1.7 10

77.7 81.7 137.7 136 1.7 10
5
5
106.7 111.7 167.7 166 1.7 10
125.7 128.7 183.7 182 1.7 10
172.7 175.7 230.7 229 1.7 10
220.7 223.7 278.7 277 1.7 10
267.7 270.7 325.7 324 1.7 10

315.7 318.7 373.7 372 1.7 10
6
6
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N047
N051,N052
Q001
DRILLING
DCON
3
5
PL
95.5 100.5 155.5 154 1.5
MWS0900MB
MWS0900LB
MWS0900X8DB
MWS0900X10DB
MWS0900X15DB
MWS0900X20DB
MWS0900X25DB
MWS0900X30DB
MWS0910MB
MWS0910LB
MWS0910X8DB
MWS0910X10DB
MWS0910X15DB
MWS0910X20DB
MWS0910X25DB
MWS0910X30DB
MWS0920MB
MWS0920LB
MWS0920X8DB
MWS0920X10DB
MWS0920X15DB
MWS0920X20DB
MWS0920X25DB
MWS0920X30DB
MWS0930MB
MWS0930LB
MWS0930X8DB
MWS0930X10DB
MWS0930X15DB
MWS0930X20DB
MWS0930X25DB
MWS0930X30DB
MWS0940MB
MWS0940LB
MWS0940X8DB
MWS0940X10DB
MWS0940X15DB
MWS0940X20DB
MWS0940X25DB
MWS0940X30DB
MWS0950MB
MWS0950LB
MWS0950X8DB
MWS0950X10DB
MWS0950X15DB
MWS0950X20DB
MWS0950X25DB
MWS0950X30DB
LF
25
30
OAL
20
3
5
(mm) (l/d)
LH
5
5
Type
LCF
15
VP15TF
8.4
Hole Depth
DCON
10
9
9
PL
44.0 46.5 101.5 100 1.5

69.5 73.5 128.5 127 1.5
LF
MWS0840MB
MWS0840LB
MWS0840X8DB
MWS0840X10DB
MWS0840X15DB
MWS0840X20DB
MWS0840X25DB
MWS0840X30DB
MWS0850MB
MWS0850LB
MWS0850X8DB
MWS0850X10DB
MWS0850X15DB
MWS0850X20DB
MWS0850X25DB
MWS0850X30DB
MWS0860MB
MWS0860LB
MWS0860X8DB
MWS0860X10DB
MWS0860X15DB
MWS0860X20DB
MWS0860X25DB
MWS0860X30DB
MWS0870MB
MWS0870LB
MWS0870X8DB
MWS0870X10DB
MWS0870X15DB
MWS0870X20DB
MWS0870X25DB
MWS0870X30DB
MWS0880MB
MWS0880LB
MWS0880X8DB
MWS0880X10DB
MWS0880X15DB
MWS0880X20DB
MWS0880X25DB
MWS0880X30DB
MWS0890MB
MWS0890LB
MWS0890X8DB
MWS0890X10DB
MWS0890X15DB
MWS0890X20DB
MWS0890X25DB
MWS0890X30DB
OAL
Order Number
LH
3
5
DC
Dimensions (mm)
Stock
Type
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
N041
MWS
WSTAR DRILLS
3
5
9.7
10
15
20
25
30
3
5
10
9.8
15
20
25
30
3
5
10
9.9
15
20
25
30
3
5
10
15
20
25
30
3
5
10.1 10
15
20
25
DRILLING
10.0
131.7 134.7 189.7 188 1.7 10
10.2 10
181.7 184.7 239.7 238 1.7 10
15
231.7 234.7 289.7 288 1.7 10
281.7 284.7 339.7 338 1.7 10

331.7 334.7 389.7 388 1.7 10
6
6
20
25
51.8 51.8 107.8 106 1.8 10

81.8 81.8 137.8 136 1.8 10
5
5
111.8 111.8 167.8 166 1.8 10
131.8 134.8 189.8 188 1.8 10
15
181.8 184.8 239.8 238 1.8 10
231.8 234.8 289.8 288 1.8 10
20
25
281.8 284.8 339.8 338 1.8 10

331.8 334.8 389.8 388 1.8 10
6
6
3
5
51.8 51.8 107.8 106 1.8 10

81.8 81.8 137.8 136 1.8 10
5
5
10.4 10
111.8 111.8 167.8 166 1.8 10
15
131.8 134.8 189.8 188 1.8 10
181.8 184.8 239.8 238 1.8 10
20
25
231.8 234.8 289.8 288 1.8 10
281.8 284.8 339.8 338 1.8 10

331.8 334.8 389.8 388 1.8 10
6
6
51.8 51.8 107.8 106 1.8 10

81.8 81.8 137.8 136 1.8 10
3
5
10.3 10
3
5
5
5
10.5 10
15
111.8 111.8 167.8 166 1.8 10
131.8 134.8 189.8 188 1.8 10
20
25
181.8 184.8 239.8 238 1.8 10
231.8 234.8 289.8 288 1.8 10
3
5
281.8 284.8 339.8 338 1.8 10

331.8 334.8 389.8 388 1.8 10
6
6
10.6 10
51.8 51.8 107.8 106 1.8 10

81.8 81.8 137.8 136 1.8 10
5
5
15
20
25
3
5
111.8 111.8 167.8 166 1.8 10
131.8 134.8 189.8 188 1.8 10
181.8 184.8 239.8 238 1.8 10
231.8 234.8 289.8 288 1.8 10
281.8 284.8 339.8 338 1.8 10

331.8 334.8 389.8 388 1.8 10
6
6
10.7 10
15
54.3 56.8 117.8 116 1.8

85.8 89.8 150.8 149 1.8
11
11
5
5
20
25
117.8 122.8 183.8 182 1.8
11
138.8 141.8 202.8 201 1.8
11
3
5
190.8 193.8 254.8 253 1.8
11
243.8 246.8 307.8 306 1.8

295.8 298.8 359.8 358 1.8
11
11
6
6
10.8 10
15
20
25
N042
DCON
PL
25
30
111.7 111.7 167.7 166 1.7 10
MWS1020MB
MWS1020LB
MWS1020X8DB
MWS1020X10DB
MWS1020X15DB
MWS1020X20DB
MWS1020X25DB
MWS1030MB
MWS1030LB
MWS1030X8DB
MWS1030X10DB
MWS1030X15DB
MWS1030X20DB
MWS1030X25DB
MWS1040MB
MWS1040LB
MWS1040X8DB
MWS1040X10DB
MWS1040X15DB
MWS1040X20DB
MWS1040X25DB
MWS1050MB
MWS1050LB
MWS1050X8DB
MWS1050X10DB
MWS1050X15DB
MWS1050X20DB
MWS1050X25DB
MWS1060MB
MWS1060LB
MWS1060X8DB
MWS1060X10DB
MWS1060X15DB
MWS1060X20DB
MWS1060X25DB
MWS1070MB
MWS1070LB
MWS1070X8DB
MWS1070X10DB
MWS1070X15DB
MWS1070X20DB
MWS1070X25DB
MWS1080MB
MWS1080LB
MWS1080X8DB
MWS1080X10DB
MWS1080X15DB
MWS1080X20DB
MWS1080X25DB
LF
OAL
20
Type
LH
15
VP15TF
9.6
Hole Depth
DCON
10
5
5
PL
(mm) (l/d)
51.7 51.7 107.7 106 1.7 10

81.7 81.7 137.7 136 1.7 10
LF
MWS0960MB
MWS0960LB
MWS0960X8DB
MWS0960X10DB
MWS0960X15DB
MWS0960X20DB
MWS0960X25DB
MWS0960X30DB
MWS0970MB
MWS0970LB
MWS0970X8DB
MWS0970X10DB
MWS0970X15DB
MWS0970X20DB
MWS0970X25DB
MWS0970X30DB
MWS0980MB
MWS0980LB
MWS0980X8DB
MWS0980X10DB
MWS0980X15DB
MWS0980X20DB
MWS0980X25DB
MWS0980X30DB
MWS0990MB
MWS0990LB
MWS0990X8DB
MWS0990X10DB
MWS0990X15DB
MWS0990X20DB
MWS0990X25DB
MWS0990X30DB
MWS1000MB
MWS1000LB
MWS1000X8DB
MWS1000X10DB
MWS1000X15DB
MWS1000X20DB
MWS1000X25DB
MWS1000X30DB
MWS1010MB
MWS1010LB
MWS1010X8DB
MWS1010X10DB
MWS1010X15DB
MWS1010X20DB
MWS1010X25DB
OAL
LH
3
5
DC
Dimensions (mm)
Stock
Order Number
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
Type
54.4 56.9 117.9 116 1.9
11
85.9 89.9 150.9 149 1.9
11
117.9 122.9 183.9 182 1.9
11
138.9 141.9 202.9 201 1.9
11
190.9 193.9 254.9 253 1.9
11
243.9 246.9 307.9 306 1.9

295.9 298.9 359.9 358 1.9
11
11
6
6
54.4 56.9 117.9 116 1.9

85.9 89.9 150.9 149 1.9
11
11
5
5
117.9 122.9 183.9 182 1.9
11
138.9 141.9 202.9 201 1.9
11
190.9 193.9 254.9 253 1.9
11
243.9 246.9 307.9 306 1.9

295.9 298.9 359.9 358 1.9
11
11
6
6
54.4 56.9 117.9 116 1.9

85.9 89.9 150.9 149 1.9
11
11
5
5
117.9 122.9 183.9 182 1.9
11
138.9 141.9 202.9 201 1.9
11
190.9 193.9 254.9 253 1.9
11
243.9 246.9 307.9 306 1.9

295.9 298.9 359.9 358 1.9
11
11
6
6
54.4 56.9 117.9 116 1.9

85.9 89.9 150.9 149 1.9
11
11
5
5
117.9 122.9 183.9 182 1.9
11
138.9 141.9 202.9 201 1.9
11
190.9 193.9 254.9 253 1.9
11
243.9 246.9 307.9 306 1.9

295.9 298.9 359.9 358 1.9
11
11
6
6
56.9 56.9 117.9 116 1.9

89.9 89.9 150.9 149 1.9
11
11
5
5
122.9 122.9 183.9 182 1.9
11
144.9 147.9 208.9 207 1.9
11
199.9 202.9 263.9 262 1.9
11
254.9 257.9 318.9 317 1.9

309.9 312.9 373.9 372 1.9
11
11
6
6
56.9 56.9 117.9 116 1.9

89.9 89.9 150.9 149 1.9
11
11
5
5
122.9 122.9 183.9 182 1.9
11
144.9 147.9 208.9 207 1.9
11
199.9 202.9 263.9 262 1.9
11
254.9 257.9 318.9 317 1.9

309.9 312.9 373.9 372 1.9
11
11
6
6
57.0 57.0 118.0 116 2.0

90.0 90.0 151.0 149 2.0
11
11
5
5
123.0 123.0 184.0 182 2.0
11
145.0 148.0 209.0 207 2.0
11
200.0 203.0 264.0 262 2.0
11
255.0 258.0 319.0 317 2.0

310.0 313.0 374.0 372 2.0
11
11
6
6
CARBIDE
15
20
25
3
5
11.0 10
15
20
25
3
5
11.1 10
15
20
25
3
5
11.2 10
15
20
25
3
5
11.3 10
15
20
25
3
5
11.4 10
15
20
25
3
5
11.5 10
15
20
25
a
a
123.0 123.0 184.0 182 2.0
11
145.0 148.0 209.0 207 2.0
11
11.6 10
200.0 203.0 264.0 262 2.0
11
15
255.0 258.0 319.0 317 2.0

310.0 313.0 374.0 372 2.0
11
11
6
6
20
25
57.0 57.0 118.0 116 2.0

90.0 90.0 151.0 149 2.0
11
11
5
5
3
5
123.0 123.0 184.0 182 2.0
11
145.0 148.0 209.0 207 2.0
11
11.7 10
200.0 203.0 264.0 262 2.0
11
15
255.0 258.0 319.0 317 2.0

310.0 313.0 374.0 372 2.0
11
11
6
6
20
25
59.5 62.0 124.0 122 2.0 12

94.0 98.0 160.0 158 2.0 12
5
5
3
5
129.0 134.0 196.0 194 2.0 12
152.0 155.0 217.0 215 2.0 12
11.8 10
209.0 212.0 274.0 272 2.0 12
15
267.0 270.0 332.0 330 2.0 12

324.0 327.0 389.0 387 2.0 12
6
6
20
25
59.5 62.0 124.0 122 2.0 12

94.0 98.0 160.0 158 2.0 12
5
5
3
5
129.0 134.0 196.0 194 2.0 12
152.0 155.0 217.0 215 2.0 12
11.9 10
209.0 212.0 274.0 272 2.0 12
15
267.0 270.0 332.0 330 2.0 12

324.0 327.0 389.0 387 2.0 12
6
6
20
25
59.6 62.1 124.1 122 2.1 12

94.1 98.1 160.1 158 2.1 12
5
5
3
5
129.1 134.1 196.1 194 2.1 12
152.1 155.1 217.1 215 2.1 12
12.0 10
209.1 212.1 274.1 272 2.1 12
15
267.1 270.1 332.1 330 2.1 12

324.1 327.1 389.1 387 2.1 12
6
6
20
25
59.6 62.1 124.1 122 2.1 12

94.1 98.1 160.1 158 2.1 12
5
5
3
5
129.1 134.1 196.1 194 2.1 12
152.1 155.1 217.1 215 2.1 12
209.1 212.1 274.1 272 2.1 12
267.1 270.1 332.1 330 2.1 12

324.1 327.1 389.1 387 2.1 12
6
6
59.6 62.1 124.1 122 2.1 12

94.1 98.1 160.1 158 2.1 12
5
5
129.1 134.1 196.1 194 2.1 12
152.1 155.1 217.1 215 2.1 12
209.1 212.1 274.1 272 2.1 12
MWS1160MB
MWS1160LB
MWS1160X8DB
MWS1160X10DB
MWS1160X15DB
MWS1160X20DB
MWS1160X25DB
MWS1170MB
MWS1170LB
MWS1170X8DB
MWS1170X10DB
MWS1170X15DB
MWS1170X20DB
MWS1170X25DB
MWS1180MB
MWS1180LB
MWS1180X8DB
MWS1180X10DB
MWS1180X15DB
MWS1180X20DB
MWS1180X25DB
MWS1190MB
MWS1190LB
MWS1190X8DB
MWS1190X10DB
MWS1190X15DB
MWS1190X20DB
MWS1190X25DB
MWS1200MB
MWS1200LB
MWS1200X8DB
MWS1200X10DB
MWS1200X15DB
MWS1200X20DB
MWS1200X25DB
MWS1210MB
MWS1210LB
MWS1210X8DB
MWS1210X10DB
MWS1210X15DB
MWS1210X20DB
MWS1220MB
MWS1220LB
MWS1220X8DB
MWS1220X10DB
MWS1220X15DB
MWS1220X20DB
267.1 270.1 332.1 330 2.1 12

324.1 327.1 389.1 387 2.1 12
6
6
12.1
12.2
a
a
10
15
20
3
5
10
15
20
DCON
PL
11
LF
90.0 90.0 151.0 149 2.0
OAL
LH
11
LCF
57.0 57.0 118.0 116 2.0
Type
62.1 62.1 124.1 122 2.1 12
98.1 98.1 160.1 158 2.1 12
134.1 134.1 196.1 194 2.1 12
158.1 161.1 223.1 221 2.1 12
218.1 221.1 283.1 281 2.1 12
278.1 281.1 343.1 341 2.1 12

338.1 341.1 403.1 401 2.1 12
6
6
62.1 62.1 124.1 122 2.1 12

98.1 98.1 160.1 158 2.1 12
5
5
134.1 134.1 196.1 194 2.1 12
158.1 161.1 223.1 221 2.1 12
218.1 221.1 283.1 281 2.1 12
278.1 281.1 343.1 341 2.1 12

338.1 341.1 403.1 401 2.1 12
6
6
62.1 62.1 124.1 122 2.1 12

98.1 98.1 160.1 158 2.1 12
5
5
134.1 134.1 196.1 194 2.1 12
158.1 161.1 223.1 221 2.1 12
218.1 221.1 283.1 281 2.1 12
278.1 281.1 343.1 341 2.1 12

338.1 341.1 403.1 401 2.1 12
6
6
62.2 62.2 124.2 122 2.2 12

98.2 98.2 160.2 158 2.2 12
5
5
134.2 134.2 196.2 194 2.2 12
158.2 161.2 223.2 221 2.2 12
218.2 221.2 283.2 281 2.2 12
278.2 281.2 343.2 341 2.2 12

338.2 341.2 403.2 401 2.2 12
6
6
62.2 62.2 124.2 122 2.2 12

98.2 98.2 160.2 158 2.2 12
5
5
134.2 134.2 196.2 194 2.2 12
158.2 161.2 223.2 221 2.2 12
218.2 221.2 283.2 281 2.2 12
278.2 281.2 343.2 341 2.2 12

338.2 341.2 403.2 401 2.2 12
6
6
64.7 67.2 130.2 128 2.2 13

102.2 106.2 169.2 167 2.2 13
5
5
140.2 145.2 208.2 206 2.2 13
165.2 168.2 231.2 229 2.2 13
227.2 230.2 293.2 291 2.2 13

290.2 293.2 356.2 354 2.2 13
6
6
64.7 67.2 130.2 128 2.2 13

102.2 106.2 169.2 167 2.2 13
5
5
140.2 145.2 208.2 206 2.2 13
165.2 168.2 231.2 229 2.2 13
227.2 230.2 293.2 291 2.2 13

290.2 293.2 356.2 354 2.2 13
6
6
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N047
N051,N052
Q001
DRILLING
10.9 10
(mm) (l/d)
VP15TF
DCON
PL
MWS1090MB
MWS1090LB
MWS1090X8DB
MWS1090X10DB
MWS1090X15DB
MWS1090X20DB
MWS1090X25DB
MWS1100MB
MWS1100LB
MWS1100X8DB
MWS1100X10DB
MWS1100X15DB
MWS1100X20DB
MWS1100X25DB
MWS1110MB
MWS1110LB
MWS1110X8DB
MWS1110X10DB
MWS1110X15DB
MWS1110X20DB
MWS1110X25DB
MWS1120MB
MWS1120LB
MWS1120X8DB
MWS1120X10DB
MWS1120X15DB
MWS1120X20DB
MWS1120X25DB
MWS1130MB
MWS1130LB
MWS1130X8DB
MWS1130X10DB
MWS1130X15DB
MWS1130X20DB
MWS1130X25DB
MWS1140MB
MWS1140LB
MWS1140X8DB
MWS1140X10DB
MWS1140X15DB
MWS1140X20DB
MWS1140X25DB
MWS1150MB
MWS1150LB
MWS1150X8DB
MWS1150X10DB
MWS1150X15DB
MWS1150X20DB
MWS1150X25DB
LF
OAL
Order Number
LH
(mm) (l/d)
DC
Dimensions (mm)
Stock
Type
LCF
Order Number
Hole Depth
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
N043
MWS
WSTAR DRILLS
10
15
20
3
5
10
15
20
3
5
12.4
12.5
12.6
12.7
DRILLING
12.8
12.9
13.0
10
15
20
3
5
10
15
20
3
5
10
15
20
3
5
10
15
20
3
5
10
15
20
a
a
6
6
15
20
64.8 67.3 130.3 128 2.3 13

102.3 106.3 169.3 167 2.3 13
5
5
3
5
140.3 145.3 208.3 206 2.3 13
165.3 168.3 231.3 229 2.3 13
10
227.3 230.3 293.3 291 2.3 13

290.3 293.3 356.3 354 2.3 13
6
6
15
20
64.8 67.3 130.3 128 2.3 13

102.3 106.3 169.3 167 2.3 13
5
5
3
5
140.3 145.3 208.3 206 2.3 13
165.3 168.3 231.3 229 2.3 13
227.3 230.3 293.3 291 2.3 13

290.3 293.3 356.3 354 2.3 13
140.2 145.2 208.2 206 2.2 13
165.2 168.2 231.2 229 2.2 13
227.2 230.2 293.2 291 2.2 13

290.2 293.2 356.2 354 2.2 13
13.1
13.2
10
6
6
15
20
67.3 67.3 130.3 128 2.3 13

106.3 106.3 169.3 167 2.3 13
5
5
3
5
145.3 145.3 208.3 206 2.3 13
171.3 174.3 237.3 235 2.3 13
236.3 239.3 302.3 300 2.3 13

301.3 304.3 367.3 365 2.3 13
13.3
10
6
6
15
20
67.3 67.3 130.3 128 2.3 13

106.3 106.3 169.3 167 2.3 13
5
5
3
5
145.3 145.3 208.3 206 2.3 13
171.3 174.3 237.3 235 2.3 13
13.4
13.5
10
a
a
236.3 239.3 302.3 300 2.3 13

301.3 304.3 367.3 365 2.3 13
6
6
15
20
67.3 67.3 130.3 128 2.3 13

106.3 106.3 169.3 167 2.3 13
5
5
3
5
145.3 145.3 208.3 206 2.3 13
171.3 174.3 237.3 235 2.3 13
236.3 239.3 302.3 300 2.3 13

301.3 304.3 367.3 365 2.3 13
10
6
6
15
20
67.3 67.3 130.3 128 2.3 13

106.3 106.3 169.3 167 2.3 13
5
5
3
5
145.3 145.3 208.3 206 2.3 13
171.3 174.3 237.3 235 2.3 13
10
236.3 239.3 302.3 300 2.3 13

301.3 304.3 367.3 365 2.3 13
6
6
15
20
67.4 67.4 130.4 128 2.4 13

106.4 106.4 169.4 167 2.4 13
5
5
3
5
145.4 145.4 208.4 206 2.4 13
171.4 174.4 237.4 235 2.4 13
10
236.4 239.4 302.4 300 2.4 13

301.4 304.4 367.4 365 2.4 13
6
6
15
20
13.6
13.7
13.8
N044
DCON
3
5
10
102.2 106.2 169.2 167 2.2 13
PL
LF
15
20
MWS1310MB
MWS1310LB
MWS1310X8DB
MWS1310X10DB
MWS1310X15DB
MWS1310X20DB
MWS1320MB
MWS1320LB
MWS1320X8DB
MWS1320X10DB
MWS1320X15DB
MWS1320X20DB
MWS1330MB
MWS1330LB
MWS1330X8DB
MWS1330X10DB
MWS1330X15DB
MWS1330X20DB
MWS1340MB
MWS1340LB
MWS1340X8DB
MWS1340X10DB
MWS1340X15DB
MWS1340X20DB
MWS1350MB
MWS1350LB
MWS1350X8DB
MWS1350X10DB
MWS1350X15DB
MWS1350X20DB
MWS1360MB
MWS1360LB
MWS1360X8DB
MWS1360X10DB
MWS1360X15DB
MWS1360X20DB
MWS1370MB
MWS1370LB
MWS1370X8DB
MWS1370X10DB
MWS1370X15DB
MWS1370X20DB
MWS1380MB
MWS1380LB
MWS1380X8DB
MWS1380X10DB
MWS1380X15DB
MWS1380X20DB
(mm) (l/d)
64.7 67.2 130.2 128 2.2 13
OAL
Type
LH
10
VP15TF
Hole Depth
3
5
DCON
PL
MWS1230MB
MWS1230LB
MWS1230X8DB
MWS1230X10DB
MWS1230X15DB
MWS1230X20DB
MWS1240MB
MWS1240LB
MWS1240X8DB
MWS1240X10DB
MWS1240X15DB
MWS1240X20DB
MWS1250MB
MWS1250LB
MWS1250X8DB
MWS1250X10DB
MWS1250X15DB
MWS1250X20DB
MWS1260MB
MWS1260LB
MWS1260X8DB
MWS1260X10DB
MWS1260X15DB
MWS1260X20DB
MWS1270MB
MWS1270LB
MWS1270X8DB
MWS1270X10DB
MWS1270X15DB
MWS1270X20DB
MWS1280MB
MWS1280LB
MWS1280X8DB
MWS1280X10DB
MWS1280X15DB
MWS1280X20DB
MWS1290MB
MWS1290LB
MWS1290X8DB
MWS1290X10DB
MWS1290X15DB
MWS1290X20DB
MWS1300MB
MWS1300LB
MWS1300X8DB
MWS1300X10DB
MWS1300X15DB
MWS1300X20DB
LF
OAL
LH
(mm) (l/d)
DC
Dimensions (mm)
Stock
Order Number
LCF
Order Number
12.3
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
89.9 72.4 136.4 134 2.4 14

110.4 114.4 178.4 176 2.4 14
Type
5
5
151.4 156.4 220.4 218 2.4 14
178.4 181.4 245.4 243 2.4 14
245.4 248.4 312.4 310 2.4 14

313.4 316.4 380.4 378 2.4 14
6
6
69.9 72.4 136.4 134 2.4 14

110.4 114.4 178.4 176 2.4 14
5
5
151.4 156.4 220.4 218 2.4 14
178.4 181.4 245.4 243 2.4 14
245.4 248.4 312.4 310 2.4 14

313.4 316.4 380.4 378 2.4 14
6
6
69.9 72.4 136.4 134 2.4 14

110.4 114.4 178.4 176 2.4 14
5
5
151.4 156.4 220.4 218 2.4 14
178.4 181.4 245.4 243 2.4 14
245.4 248.4 312.4 310 2.4 14

313.4 316.4 380.4 378 2.4 14
6
6
69.9 72.4 136.4 134 2.4 14

110.4 114.4 178.4 176 2.4 14
5
5
151.4 156.4 220.4 218 2.4 14
178.4 181.4 245.4 243 2.4 14
245.4 248.4 312.4 310 2.4 14

313.4 316.4 380.4 378 2.4 14
6
6
70.0 72.5 136.5 134 2.5 14

110.5 114.5 178.5 176 2.5 14
5
5
151.5 156.5 220.5 218 2.5 14
178.5 181.5 245.5 243 2.5 14
245.5 248.5 312.5 310 2.5 14

313.5 316.5 380.5 378 2.5 14
6
6
72.5 72.5 136.5 134 2.5 14

114.5 114.5 178.5 176 2.5 14
5
5
156.5 156.5 220.5 218 2.5 14
184.5 187.5 251.5 249 2.5 14
254.5 257.5 321.5 319 2.5 14

324.5 327.5 391.5 389 2.5 14
6
6
72.5 72.5 136.5 134 2.5 14

114.5 114.5 178.5 176 2.5 14
5
5
156.5 156.5 220.5 218 2.5 14
184.5 187.5 251.5 249 2.5 14
254.5 257.5 321.5 319 2.5 14

324.5 327.5 391.5 389 2.5 14
6
6
72.5 72.5 136.5 134 2.5 14

114.5 114.5 178.5 176 2.5 14
5
5
156.5 156.5 220.5 218 2.5 14
184.5 187.5 251.5 249 2.5 14
254.5 257.5 321.5 319 2.5 14

324.5 327.5 391.5 389 2.5 14
6
6
CARBIDE
3
14.1 5
8
a
r
3
14.2 5
8
a
a
a
14.3 5
3
14.4 5
8
a
a
r
3
14.5 5
8
a
a
a
14.6 5
3
14.7 5
8
3
14.8 5
8
3
14.9 5
8
a
r
a
a
r
a
a
r
3
15.0 5
8
3
15.1 5
8
a
a
15.2 5
3
15.3 5
8
a
a
r
184.5 187.5 251.5 249 2.5 14
254.5 257.5 321.5 319 2.5 14

324.5 327.5 391.5 389 2.5 14
6
6
15.5 5
72.5 72.5 136.5 134 2.5 14

114.5 114.5 178.5 176 2.5 14
5
5
156.5 156.5 220.5 218 2.5 14
3
15.6 5
8
184.5 187.5 251.5 249 2.5 14
254.5 257.5 321.5 319 2.5 14

324.5 327.5 391.5 389 2.5 14
6
6
3
15.7 5
8
75.1 77.6 142.6 140 2.6 15

118.6 122.6 187.6 185 2.6 15
162.6 167.6 227.6 225 2.6 15
5
5
5
3
15.8 5
8
75.1 77.6 142.6 140 2.6 15

118.6 122.6 187.6 185 2.6 15
162.6 167.6 227.6 225 2.6 15
5
5
5
3
15.9 5
8
75.1 77.6 142.6 140 2.6 15

118.6 122.6 187.6 185 2.6 15
162.6 167.6 227.6 225 2.6 15
5
5
5
16.0 5
75.1 77.6 142.6 140 2.6 15

118.6 122.6 187.6 185 2.6 15
162.6 167.6 227.6 225 2.6 15
5
5
5
75.1 77.6 142.6 140 2.6 15

118.6 122.6 187.6 185 2.6 15
162.6 167.6 227.6 225 2.6 15
5
5
5
77.7 77.7 142.7 140 2.7 15

122.7 122.7 187.7 185 2.7 15
167.7 167.7 227.7 225 2.7 15
5
5
5
77.7 77.7 142.7 140 2.7 15

122.7 122.7 187.7 185 2.7 15
167.7 167.7 227.7 225 2.7 15
5
5
5
77.7 77.7 142.7 140 2.7 15

122.7 122.7 187.7 185 2.7 15
167.7 167.7 227.7 225 2.7 15
5
5
5
77.7 77.7 142.7 140 2.7 15

122.7 122.7 187.7 185 2.7 15
167.7 167.7 227.7 225 2.7 15
5
5
5
77.7 77.7 142.7 140 2.7 15

122.7 122.7 187.7 185 2.7 15
167.7 167.7 227.7 225 2.7 15
5
5
5
80.2 82.7 147.7 145 2.7 16

126.7 130.7 195.7 193 2.7 16
173.7 183.7 243.7 241 2.7 16
5
5
5
80.3 82.8 147.8 145 2.8 16

126.8 130.8 195.8 193 2.8 16
173.8 183.8 243.8 241 2.8 16
5
5
5
80.3 82.8 147.8 145 2.8 16

126.8 130.8 195.8 193 2.8 16
173.8 183.8 243.8 241 2.8 16
5
5
5
a
r
a
a
r
a
a
r
a
a
3
16.1
5
r
r
16.2
3
5
16.3
3
5
16.4
3
5
16.5
3
5
16.6
3
5
16.7
3
5
16.8
3
5
16.9
3
5
17.0
3
5
17.1
3
5
17.2
3
5
17.3
3
5
17.4
3
5
17.5
3
5
r
a
a
r
r
r
80.3 82.8 147.8 145 2.8 16
126.8 130.8 195.8 193 2.8 16

173.8 183.8 243.8 241 2.8 16
5
5
80.3 82.8 147.8 145 2.8 16

126.8 130.8 195.8 193 2.8 16
173.8 183.8 243.8 241 2.8 16
5
5
5
82.8 82.8 147.8 145 2.8 16

130.8 130.8 195.8 193 2.8 16
178.8 183.8 243.8 241 2.8 16
5
5
5
82.9 82.9 147.9 145 2.9 16

130.9 130.9 195.9 193 2.9 16
178.9 183.9 243.9 241 2.9 16
5
5
5
82.9 82.9 147.9 145 2.9 16

130.9 130.9 195.9 193 2.9 16
178.9 183.9 243.9 241 2.9 16
5
5
5
82.9 82.9 147.9 145 2.9 16

130.9 130.9 195.9 193 2.9 16
178.9 183.9 243.9 241 2.9 16
5
5
5
82.9 82.9 147.9 145 2.9 16

130.9 130.9 195.9 193 2.9 16
178.9 183.9 243.9 241 2.9 16
5
5
5
85.4 87.9 152.9 150 2.9 17

134.9 138.9 203.9 201 2.9 17
5
5
85.4 87.9 152.9 150 2.9 17

134.9 138.9 203.9 201 2.9 17
5
5
85.5 88.0 153.0 150 3.0 17

135.0 139.0 204.0 201 3.0 17
5
5
85.5 88.0 153.0 150 3.0 17

135.0 139.0 204.0 201 3.0 17
5
5
85.5 88.0 153.0 150 3.0 17

135.0 139.0 204.0 201 3.0 17
5
5
88.0 88.0 153.0 150 3.0 17

139.0 139.0 204.0 201 3.0 17
5
5
88.0 88.0 153.0 150 3.0 17

139.0 139.0 204.0 201 3.0 17
5
5
88.1 88.1 153.1 150 3.1 17

139.1 139.1 204.1 201 3.1 17
5
5
88.1 88.1 153.1 150 3.1 17

139.1 139.1 204.1 201 3.1 17
5
5
88.1 88.1 153.1 150 3.1 17

139.1 139.1 204.1 201 3.1 17
5
5
90.6 93.1 158.1 155 3.1 18

143.1 147.1 212.1 209 3.1 18
5
5
90.6 93.1 158.1 155 3.1 18

143.1 147.1 212.1 209 3.1 18
5
5
90.6 93.1 158.1 155 3.1 18

143.1 147.1 212.1 209 3.1 18
5
5
90.7 93.2 158.2 155 3.2 18

143.2 147.2 212.2 209 3.2 18
5
5
90.7 93.2 158.2 155 3.2 18

143.2 147.2 212.2 209 3.2 18
5
5
OPERATION GUIDANCE
CUTTING CONDITIONS
N047
Type
TECHNICAL DATA
N051,N052
Q001
DRILLING
15
20
DCON
156.5 156.5 220.5 218 2.5 14
MWS1540MB
MWS1540LB
MWS1540X8DB
MWS1550MB
MWS1550LB
MWS1550X8DB
MWS1560MB
MWS1560LB
MWS1560X8DB
MWS1570MB
MWS1570LB
MWS1570X8DB
MWS1580MB
MWS1580LB
MWS1580X8DB
MWS1590MB
MWS1590LB
MWS1590X8DB
MWS1600MB
MWS1600LB
MWS1600X8DB
MWS1610MB
MWS1610LB
MWS1620MB
MWS1620LB
MWS1630MB
MWS1630LB
MWS1640MB
MWS1640LB
MWS1650MB
MWS1650LB
MWS1660MB
MWS1660LB
MWS1670MB
MWS1670LB
MWS1680MB
MWS1680LB
MWS1690MB
MWS1690LB
MWS1700MB
MWS1700LB
MWS1710MB
MWS1710LB
MWS1720MB
MWS1720LB
MWS1730MB
MWS1730LB
MWS1740MB
MWS1740LB
MWS1750MB
MWS1750LB
PL
10
LF
OAL
14.0
15.4 5
5
5
LH
(mm) (l/d)
72.5 72.5 136.5 134 2.5 14

114.5 114.5 178.5 176 2.5 14
Order Number
LCF
3
5
DC
Dimensions (mm)
Stock
VP15TF
Type
Hole Depth
15
20
DCON
10
PL
13.9
LF
MWS1390MB
MWS1390LB
MWS1390X8DB
MWS1390X10DB
MWS1390X15DB
MWS1390X20DB
MWS1400MB
MWS1400LB
MWS1400X8DB
MWS1400X10DB
MWS1400X15DB
MWS1400X20DB
MWS1410MB
MWS1410LB
MWS1410X8DB
MWS1420MB
MWS1420LB
MWS1420X8DB
MWS1430MB
MWS1430LB
MWS1430X8DB
MWS1440MB
MWS1440LB
MWS1440X8DB
MWS1450MB
MWS1450LB
MWS1450X8DB
MWS1460MB
MWS1460LB
MWS1460X8DB
MWS1470MB
MWS1470LB
MWS1470X8DB
MWS1480MB
MWS1480LB
MWS1480X8DB
MWS1490MB
MWS1490LB
MWS1490X8DB
MWS1500MB
MWS1500LB
MWS1500X8DB
MWS1510MB
MWS1510LB
MWS1510X8DB
MWS1520MB
MWS1520LB
MWS1520X8DB
MWS1530MB
MWS1530LB
MWS1530X8DB
OAL
LH
3
5
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
N045
MWS
WSTAR DRILLS
DRILLING
3
17.6
5
17.7
3
5
17.8
3
5
17.9
3
5
18.0
3
5
18.1
3
5
18.2
3
5
18.3
3
5
18.4
3
5
18.5
3
5
18.6
3
5
18.7
3
5
18.8
3
5
18.9
3
5
19.0
3
5
19.1
3
5
19.2
3
5
19.3
3
5
19.4
3
5
19.5
3
5
19.6
3
5
19.7
3
5
19.8
3
5
19.9
3
5
20.0
3
5
MWS1760MB
MWS1760LB
MWS1770MB
MWS1770LB
MWS1780MB
MWS1780LB
MWS1790MB
MWS1790LB
MWS1800MB
MWS1800LB
MWS1810MB
MWS1810LB
MWS1820MB
MWS1820LB
MWS1830MB
MWS1830LB
MWS1840MB
MWS1840LB
MWS1850MB
MWS1850LB
MWS1860MB
MWS1860LB
MWS1870MB
MWS1870LB
MWS1880MB
MWS1880LB
MWS1890MB
MWS1890LB
MWS1900MB
MWS1900LB
MWS1910MB
MWS1910LB
MWS1920MB
MWS1920LB
MWS1930MB
MWS1930LB
MWS1940MB
MWS1940LB
MWS1950MB
MWS1950LB
MWS1960MB
MWS1960LB
MWS1970MB
MWS1970LB
MWS1980MB
MWS1980LB
MWS1990MB
MWS1990LB
MWS2000MB
MWS2000LB
5
5
20.5
3
5
93.2 93.2 158.2 155 3.2 18

147.2 147.2 212.2 209 3.2 18
5
5
21.0
3
5
93.2 93.2 158.2 155 3.2 18

147.2 147.2 212.2 209 3.2 18
5
5
21.5
3
5
93.3 93.3 158.3 155 3.3 18

147.3 147.3 212.3 209 3.3 18
5
5
22.0
3
5
93.3 93.3 158.3 155 3.3 18

147.3 147.3 212.3 209 3.3 18
5
5
22.5
3
5
95.8 98.3 163.3 160 3.3 19

151.3 155.3 220.3 217 3.3 19
5
5
23.0
3
5
95.8 98.3 163.3 160 3.3 19

151.3 155.3 220.3 217 3.3 19
5
5
23.5
3
5
95.8 98.3 163.3 160 3.3 19

151.3 155.3 220.3 217 3.3 19
5
5
24.0
3
5
95.8 98.3 163.3 160 3.3 19

151.3 155.3 220.3 217 3.3 19
5
5
24.5
3
5
95.9 98.4 163.4 160 3.4 19

151.4 155.4 220.4 217 3.4 19
5
5
25.0
3
5
98.4 98.4 163.4 160 3.4 19

155.4 155.4 220.4 217 3.4 19
5
5
98.4 98.4 163.4 160 3.4 19

155.4 155.4 220.4 217 3.4 19
5
5
98.4 98.4 163.4 160 3.4 19

155.4 155.4 220.4 217 3.4 19
5
5
98.4 98.4 163.4 160 3.4 19

155.4 155.4 220.4 217 3.4 19
5
5
98.5 98.5 163.5 160 3.5 19

155.5 155.5 220.5 217 3.5 19
5
5
101.0 103.5 168.5 165 3.5 20

159.5 163.5 228.5 225 3.5 20
5
5
101.0 103.5 168.5 165 3.5 20

159.5 163.5 228.5 225 3.5 20
5
5
101.0 103.5 168.5 165 3.5 20

159.5 163.5 228.5 225 3.5 20
5
5
101.0 103.5 168.5 165 3.5 20

159.5 163.5 228.5 225 3.5 20
5
5
101.0 103.5 168.5 165 3.5 20

159.5 163.5 228.5 225 3.5 20
5
5
103.6 103.6 168.6 165 3.6 20

163.6 163.6 228.6 225 3.6 20
5
5
103.6 103.6 168.6 165 3.6 20

163.6 163.6 228.6 225 3.6 20
5
5
103.6 103.6 168.6 165 3.6 20

163.6 163.6 228.6 225 3.6 20
5
5
103.6 103.6 168.6 165 3.6 20

163.6 163.6 228.6 225 3.6 20
5
5
103.6 103.6 168.6 165 3.6 20

163.6 163.6 228.6 225 3.6 20
5
5
MWS2050MB
MWS2050LB
MWS2100MB
MWS2100LB
MWS2150MB
MWS2150LB
MWS2200MB
MWS2200LB
MWS2250MB
MWS2250LB
MWS2300MB
MWS2300LB
MWS2350MB
MWS2350LB
MWS2400MB
MWS2400LB
MWS2450MB
MWS2450LB
MWS2500MB
MWS2500LB
N046
DCON
PL
LF
(mm) (l/d)
93.2 93.2 158.2 155 3.2 18

147.2 147.2 212.2 209 3.2 18
Order Number
OAL
DC
LH
Type
Dimensions (mm)
Stock
VP15TF
DCON
PL
LF
OAL
LH
Order Number
Hole Depth
Internal Coolant
Dimensions (mm)
LCF
(mm) (l/d)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
Type
106.7 108.7 179.7 176 3.7 21

169.7 171.7 242.7 239 3.7 21
5
5
108.8 108.8 179.8 176 3.8 21

171.8 171.8 242.8 239 3.8 21
5
5
111.9 113.9 185.9 182 3.9 22

177.9 179.9 251.9 248 3.9 22
5
5
114.0 114.0 186.0 182 4.0 22

180.0 180.0 252.0 248 4.0 22
5
5
117.1 119.1 192.1 188 4.1 23

186.1 188.1 261.1 257 4.1 23
5
5
119.2 119.2 192.2 188 4.2 23

188.2 188.2 261.2 257 4.2 23
5
5
122.3 124.3 198.3 194 4.3 24

194.3 196.3 270.3 266 4.3 24
5
5
124.4 124.4 198.4 194 4.4 24

196.4 196.4 270.4 266 4.4 24
5
5
127.5 129.5 204.5 200 4.5 25

202.5 204.5 274.5 270 4.5 25
5
5
129.5 129.5 204.5 200 4.5 25

204.5 204.5 274.5 270 4.5 25
5
5
CARBIDE

y SB/MB/LB/XB/DB Type Drill(l/d<10)
Carbon SteelAlloy Steel (180 280HB)
AISI 1010 etc
Drill Dia. Cutting Speed

Revolution
DC
(m/min)
(min-1)
(mm)
0.5
0.63
0.8
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
25.0
Work
Material
40
40
45
50
50
50
50
60
90
100
100
110
120
130
140
160
160
160
25400
20200
17900
15900
13200
9900
7900
7600
8900
7900
6300
5500
4700
4100
3700
3100
2500
2000
0.01
0.014
0.028
0.035
0.045
0.055
0.07
0.085
0.1
0.12
0.15
0.2
0.23
0.27
0.3
0.33
0.35
0.35
(0.005 0.015)
(0.008 0.020)
(0.016 0.040)
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.26 0.34)
(0.27 0.38)
(0.30 0.40)
(0.30 0.40)
Table Feed Cutting Speed Revolution

(m/min)
(mm/min)
(min-1)
250
280
500
555
590
540
550
645
890
945
945
1100
1080
1105
1110
1020
875
700
40
40
45
50
50
50
50
60
80
90
90
100
110
120
130
140
140
140
25400
20200
17900
15900
13200
9900
7900
7600
7900
7100
5700
5000
4300
3800
3400
2700
2200
1700
Feed rate
(Min. Max.)
(mm/rev)
0.01
0.014
0.028
0.035
0.045
0.055
0.07
0.085
0.1
0.12
0.15
0.2
0.23
0.27
0.3
0.33
0.35
0.35
(0.005 0.015)
(0.008 0.020)
(0.016 0.040)
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.26 0.34)
(0.27 0.38)
(0.30 0.40)
(0.30 0.40)
AISI 4340 etc

Revolution
DC
(m/min)
(min-1)
(mm)
0.5
0.63
0.8
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
25.0
Feed rate
(Min. Max.)
(mm/rev)
30
30
35
40
40
40
40
50
70
80
80
90
100
110
120
130
130
130
19000
15100
13900
12700
10600
7900
6300
6300
6900
6300
5000
4500
3900
3500
3100
2500
2000
1600
Feed rate
(Min. Max.)
(mm/rev)
0.01
0.014
0.028
0.035
0.045
0.055
0.07
0.085
0.1
0.11
0.14
0.18
0.21
0.23
0.26
0.28
0.3
0.32
(0.005 0.015)
(0.008 0.020)
(0.016 0.040)
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.07 0.14)
(0.09 0.18)
(0.11 0.24)
(0.16 0.25)
(0.19 0.27)
(0.22 0.29)
(0.23 0.33)
(0.26 0.34)
(0.28 0.35)

(m/min)
(mm/min)
(min-1)
190
210
385
440
475
430
440
535
690
690
700
810
815
805
805
700
600
510
20
20
25
30
30
30
30
40
40
40
40
50
50
50
60
60
60
60
12700
10100
9900
9500
7900
5900
4700
5000
3900
3100
2500
2500
1900
1500
1500
1100
900
700
Feed rate
(Min. Max.)
(mm/rev)
0.008
0.01
0.02
0.03
0.04
0.05
0.06
0.075
0.08
0.09
0.11
0.14
0.15
0.16
0.18
0.19
0.21
0.21
(0.005 0.010)
(0.008 0.013)
(0.016 0.026)
(0.020 0.044)
(0.030 0.053)
(0.035 0.070)
(0.040 0.080)
(0.050 0.100)
(0.06 0.10)
(0.06 0.11)
(0.08 0.14)
(0.09 0.18)
(0.10 0.19)
(0.12 0.20)
(0.15 0.21)
(0.14 0.24)
(0.15 0.26)
(0.17 0.25)
OPERATION GUIDANCE
TECHNICAL DATA
Table Feed
(mm/min)
250
280
500
555
590
540
550
645
790
850
855
1000
985
1025
1020
890
770
595
Table Feed
(mm/min)
100
100
195
285
315
295
280
375
310
275
275
350
285
240
270
205
185
145
N051,N052
Q001
DRILLING
Work
Material
N047
CARBIDE
MWS
WSTAR DRILLS
Work
Material
No 45 B etc
60-40-8 etc

Revolution
DC
(m/min)
(min-1)
(mm)
0.5
0.63
0.8
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
25.0
Work
Material
40
40
45
50
50
50
50
60
90
100
100
110
120
130
140
160
160
160
25400
20200
17900
15900
13200
9900
7900
7600
8900
7900
6300
5500
4700
4100
3700
3100
2500
2000
DRILLING
N048
0.01
0.014
0.028
0.035
0.045
0.055
0.07
0.085
0.1
0.12
0.15
0.2
0.25
0.29
0.32
0.35
0.37
0.37
(0.005 0.015)
(0.008 0.020)
(0.016 0.040)
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.31)
(0.22 0.35)
(0.26 0.37)
(0.28 0.42)
(0.30 0.44)
(0.30 0.44)

(m/min)
(mm/min)
(min-1)
250
280
500
555
590
540
550
645
890
945
945
1100
1175
1185
1180
1085
925
740
30
30
35
40
40
40
40
50
65
65
65
70
70
70
90
90
100
100
19000
15100
13900
12700
10600
7900
6300
6300
6400
5100
4100
3500
2700
2200
2300
1700
1500
1200
ASTM A6061, ASTM A7075 etc
Inconel718

Revolution
DC
(m/min)
(min-1)
(mm)
0.5
0.63
0.8
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
25.0
Feed rate
(Min. Max.)
(mm/rev)
40
40
45
60
70
80
90
100
120
120
120
150
150
150
160
160
170
170
25400
20200
17900
19000
18500
15900
14300
12700
11900
9500
7600
7500
5900
4700
4200
3100
2700
2100
Feed rate
(Min. Max.)
(mm/rev)
0.014
0.02
0.036
0.05
0.065
0.085
0.105
0.135
0.23
0.24
0.25
0.35
0.35
0.5
0.5
0.6
0.6
0.6
(0.008 0.020)
(0.012 0.030)
(0.024 0.050)
(0.030 0.075)
(0.045 0.090)
(0.053 0.120)
(0.060 0.150)
(0.075 0.200)
(0.10 0.35)
(0.12 0.35)
(0.15 0.35)
(0.20 0.50)
(0.20 0.50)
(0.20 0.80)
(0.20 0.80)
(0.20 1.00)
(0.20 1.00)
(0.20 1.00)

(m/min)
(mm/min)
(min-1)
355
400
640
950
1200
1350
1500
1710
2735
2280
1900
2625
2065
2350
2100
1860
1620
1260
10
10
10
10
10
10
15
15
20
20
20
25
25
25
25
25
30
30
6300
5000
3900
3100
2600
1900
2300
1900
1900
1500
1200
1200
900
700
600
400
400
300
Feed rate
(Min. Max.)
(mm/rev)
0.01
0.014
0.028
0.035
0.045
0.055
0.07
0.085
0.1
0.12
0.15
0.2
0.23
0.27
0.3
0.33
0.35
0.35
(0.005 0.015)
(0.008 0.020)
(0.016 0.040)
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.26 0.34)
(0.28 0.38)
(0.30 0.40)
(0.30 0.40)
Feed rate
(Min. Max.)
(mm/rev)
0.006
0.008
0.016
0.02
0.025
0.03
0.04
0.05
0.07
0.09
0.11
0.13
0.14
0.15
0.16
0.18
0.19
0.19
(0.004 0.008)
(0.007 0.010)
(0.013 0.021)
(0.016 0.027)
(0.022 0.032)
(0.025 0.040)
(0.032 0.050)
(0.040 0.060)
(0.05 0.09)
(0.06 0.11)
(0.08 0.14)
(0.09 0.16)
(0.11 0.17)
(0.12 0.17)
(0.13 0.18)
(0.14 0.21)
(0.15 0.22)
(0.15 0.22)
Table Feed
(mm/min)
190
210
385
440
475
430
440
535
640
610
615
700
620
590
690
560
525
420
Table Feed
(mm/min)
35
40
60
60
65
55
90
95
130
135
130
155
125
105
95
70
75
55
CARBIDE

y DB Type Drill(l/d>10)
Mild Steel ( < 180 HB)
AISI 1010 etc

Revolution
DC
(m/min)
(min-1)
(mm)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
Work
Material
50
50
50
60
60
90
90
90
110
110
110
130
130
15900
13200
9900
9500
7600
8900
7100
5700
5500
4300
3500
3400
2500
0.02
0.025
0.055
0.07
0.09
0.1
0.12
0.15
0.2
0.23
0.26
0.3
0.31
(0.010 0.030)
(0.016 0.037)
(0.032 0.080)
(0.040 0.100)
(0.063 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.20 0.32)
(0.25 0.34)
(0.24 0.38)

(m/min)
(mm/min)
(min-1)
320
330
545
665
685
890
850
855
1100
990
910
1020
775
40
40
40
50
50
80
80
80
90
90
90
110
110
12700
10600
7900
7900
6300
7900
6300
5000
4500
3500
2800
2900
2100
Feed rate
(Min. Max.)
(mm/rev)
0.02
0.025
0.055
0.07
0.09
0.1
0.12
0.15
0.2
0.23
0.26
0.3
0.31
(0.010 0.030)
(0.016 0.037)
(0.032 0.080)
(0.040 0.100)
(0.055 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.20 0.32)
(0.25 0.34)
(0.24 0.38)
AISI 4340 etc

Revolution
DC
(m/min)
(min-1)
(mm)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
Feed rate
(Min. Max.)
(mm/rev)
30
30
30
50
50
70
70
70
80
80
80
90
90
9500
7900
5900
7900
6300
6900
5500
4400
4000
3100
2500
2300
1700
Feed rate
(Min. Max.)
(mm/rev)
0.015
0.02
0.05
0.065
0.08
0.09
0.11
0.14
0.18
0.21
0.23
0.25
0.28
(0.009 0.028)
(0.013 0.035)
(0.027 0.076)
(0.034 0.095)
(0.045 0.120)
(0.05 0.12)
(0.07 0.15)
(0.09 0.19)
(0.11 0.25)
(0.15 0.26)
(0.15 0.30)
(0.19 0.31)
(0.19 0.36)

(m/min)
(mm/min)
(min-1)
140
160
295
515
505
620
605
615
720
650
575
575
475
30
30
30
30
40
40
40
40
50
50
50
60
60
9500
7900
5900
4700
5000
3900
3100
2500
2500
1900
1500
1500
1100
Feed rate
(Min. Max.)
(mm/rev)
0.015
0.02
0.045
0.055
0.06
0.07
0.08
0.1
0.12
0.14
0.15
0.17
0.18
(0.009 0.028)
(0.013 0.035)
(0.025 0.065)
(0.030 0.080)
(0.035 0.085)
(0.05 0.09)
(0.06 0.10)
(0.07 0.12)
(0.08 0.16)
(0.10 0.17)
(0.12 0.18)
(0.14 0.19)
(0.13 0.22)
Table Feed
(mm/min)
255
265
435
550
565
790
755
750
900
805
730
870
650
Table Feed
(mm/min)
140
155
265
255
300
270
245
250
300
265
225
255
195
DRILLING
Work
Material
OPERATION GUIDANCE
TECHNICAL DATA
N051,N052
Q001
N049
CARBIDE
MWS
WSTAR DRILLS
Work
Material
No 45 B etc
60-40-8 etc

Revolution
DC
(m/min)
(min-1)
(mm)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
Work
Material
40
40
40
50
50
90
90
90
110
110
110
130
130
12700
10600
7900
7900
6300
8900
7100
5700
5500
4300
3500
3400
2500
DRILLING
N050
0.02
0.025
0.055
0.07
0.09
0.1
0.12
0.15
0.2
0.23
0.26
0.3
0.31
(0.010 0.030)
(0.016 0.037)
(0.032 0.080)
(0.040 0.100)
(0.055 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.20 0.32)
(0.25 0.34)
(0.24 0.38)

(m/min)
(mm/min)
(min-1)
255
265
435
550
565
890
850
855
1100
990
910
1020
775
30
30
30
50
50
50
50
50
60
60
60
80
80
9500
7900
5900
7900
6300
4900
3900
3100
3000
2300
1900
2100
1500
Inconel718

Revolution
DC
(m/min)
(min-1)
(mm)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
Feed rate
(Min. Max.)
(mm/rev)
50
60
70
80
90
100
100
100
130
130
130
140
140
15900
15900
13900
12700
11400
9900
7900
6300
6500
5100
4100
3700
2700
Feed rate
(Min. Max.)
(mm/rev)
0.05
0.065
0.085
0.105
0.135
0.23
0.24
0.25
0.35
0.35
0.5
0.5
0.5
(0.030 0.075)
(0.045 0.090)
(0.053 0.120)
(0.060 0.150)
(0.075 0.200)
(0.10 0.35)
(0.12 0.35)
(0.15 0.35)
(0.20 0.50)
(0.20 0.50)
(0.20 0.80)
(0.20 0.80)
(0.20 0.80)

(m/min)
(mm/min)
(min-1)
795
1035
1180
1335
1540
2275
1895
1575
2275
1785
2050
1850
1350
10
10
10
15
15
20
20
20
20
20
20
20
20
3100
2600
1900
2300
1900
1900
1500
1200
1000
700
600
500
300
Feed rate
(Min. Max.)
(mm/rev)
0.015
0.02
0.05
0.065
0.08
0.09
0.11
0.14
0.18
0.21
0.23
0.25
0.28
(0.009 0.028)
(0.013 0.035)
(0.027 0.076)
(0.034 0.095)
(0.045 0.120)
(0.05 0.12)
(0.07 0.15)
(0.09 0.19)
(0.11 0.25)
(0.15 0.26)
(0.15 0.30)
(0.19 0.31)
(0.19 0.36)
Feed rate
(Min. Max.)
(mm/rev)
0.02
0.025
0.03
0.04
0.05
0.07
0.09
0.11
0.13
0.14
0.15
0.16
0.17
(0.016 0.027)
(0.022 0.032)
(0.025 0.040)
(0.032 0.050)
(0.040 0.060)
(0.05 0.09)
(0.06 0.11)
(0.08 0.14)
(0.09 0.16)
(0.11 0.16)
(0.12 0.17)
(0.13 0.18)
(0.14 0.19)
Table Feed
(mm/min)
140
160
295
515
505
440
430
435
540
480
435
525
420
Table Feed
(mm/min)
60
65
55
90
95
130
135
130
130
100
90
80
50
CARBIDE
y SB/MB/LB/XB Type Drill OPERATIONAL GUIDANCE
Drill Length
Drill Installation
Installation Tolerance(DC>3)
A > DC x 1.5(DCover 2.0 for DC<3)
Run-out < 0.03mm
Drill Installation
Coolant Handling
Thin Workpiece
Adjusting Screw
Drill Holding
DC

Through Coolant Type(DC>3)

Revolving
Coolant
Machine Type
1DC
Spindles
Through
Coolant Type

0.51MPa (2-3MPa for DC<5,
1.5MPa at minimum for DC<3
Recommended coolant pressure:>3Mpa).
(For DC>3)
zWhen machining a prepared hole with

the MWE-SB please set the depth to 1DC
(DC=drill diameter). For pilot hole drilling
when DC is up to 3, use the SB type drill.
xUse the prepared hole as a guide
when using a drill with an oil hole.
Depending on the cutting conditions,
peck feed is recommended.
Interrupted Cutting(DC>3)
Stepped Holes(DC>3)

diameter drills. Always
use a fine mesh filter as a
coolant exchange is
recommended.
If Bending
Occurs
Support
the Workpiece
Burring and Workpiece Chipping(DC>3)
One Process
zLower the feed
when drilling
the interrupted
part.
zSpot face with

an end mill
prior to drilling.

A tool for machining both
*chamfer
and spot face can

cutting.
xAdd a 45chamfer.
DRILLING
Requires Prior
Machining
y NOTES ON USE (For DC<3)

aPlease use a fine mesh filter (mesh<3!m) for coolant to prevent jamming in the oil hole.
aFor deep drilling with the long type drill, machining a pilot hole is recommended.
(Otherwise, centrifugal forces may cause drill breakage.)
TECHNICAL DATA
Q001
N051
CARBIDE
MWS
WSTAR DRILLS
y DB Type Drill(L/D>10, DC<3) OPERATIONAL GUIDANCE
FLAT FACE DRILLING aDrilling a blind hole

y 1. Drilling a pilot hole
zUse the SB type drill.

xEnsure a high precision hole is drilled for the guide.
cDrill depth : Approx 1DC.
(Adjust the pilot hole depth according to the length of the long type drill.)
y 3. Drill the deep hole
zStart cutting at the recommended speed and feed with a non-peck

(continuous feed) cycle.
y 2. Initial cutting with the long type drill
zPenetrate the guide hole at low revolution. (Revolution

1000min-1, feed rate 0.20.3mm/rev)
xStop the long type drill 0.51.0mm short of the guide hole bottom.
y 4. Drill retraction
zAfter drilling, lower the cutting revolution about 0.51.0mm short of the
hole end. (Revolution of around 1000min-1)
xRetract the drill to the pilot hole depth starting point at a feed rate of
3000mm/min.
cFinally, clear the hole at a cutting speed of 2030m/min and feed rate
of 0.20.3mm/rev.
INTERRUPED DRILLING aDrilling and breaking through on irregular faces or angles

y 1. Spot facing
zMachine a flat or the irregular face by using an end mill or slot drill
capable of spot facing. Make the spot face diameter the same size as
the required deep hole diameter.
DRILLING
zPenetrate the guide hole at a low revolution. (Revolution 1000min-1, feed

rate 0.20.3mm/rev)
xStop the long type drill 0.51.0mm short of the guide hole bottom.
y 5. Breaking through
zWhen breaking through, the cutting edge can be damaged.

xFeed rate should be half the normal feed.
N052
zUse a drill with a larger (flatter) point angle than the long type.
TheMWS-SB type is recommended.

zFinally clear the hole at a revolution speed of 1000min-1 and feed rate of
0.20.3mm/rev.
3000mm/min.
CARBIDE
y OPERATIONAL GUIDANCE FOR THE LONG TYPE DRILL (L/D>3)

zUse a drill with a larger (flatter) point angle than the super long type.
Mitsubishi type MZE, MZS, MWE or MWS is recommended.
xUse a drill with the same diameter as the deep hole drill.
cDrill depth : Approx 1DC or deeper.
vEnsure a high precision hole is drilled for the guide.

zPenetrate the guide hole at low revolution.

(Cutting speed 2030m/min, feed rate 0.20.3mm/rev)
xStop the long type drill 13mm short of the guide hole bottom.
zAfter drilling, lower the cutting revolution about 12mm short of the
hole end. (Cutting speed of around 2030m/min)
3000mm/min.
cFinally, clear the hole at a cutting speed of 2030m/min and feed rate
of 0.20.3mm/rev.
zPenetrate the guide hole at a low revolution.

(Cutting speed 2030m/min, feed rate 0.20.3mm/rev)
xStop the long type drill 13mm short of the guide hole bottom.

xA feed rate of 0.050.1mm/rev is recommended.
Mitsubishi type MZE, MZS, MWE or MWS is recommended.
xUse a drill with the same diameter as the deep hole drill.
cDrill depth : Approx 1DC or deeper.
vEnsure a high precision hole is drilled for the guide.

DRILLING
y 1. Spot facing
zFinally clear the hole at a cutting speed of 2030m/min and feed rate of
0.20.3mm/rev.
3000mm/min.
TECHNICAL DATA
Q001
N053
CARBIDE
MWE
WSTAR DRILLS
P
Steel
a For high accuracy and efficient drilling of steels, carbon steels and difficult-to-cut materials.
a Also suitable for lower speed applications.
DC=3
3<DC < 6 6<DC < 10 10<DC < 1818<DC < 25
0
0.014
0
MWE-SA/MA 0.014
0
MWE-SB/MB 0.006
h
h6
0
0.018
0
0.018
0
0.008
0
0.027
0
0.027
0
0.011
0
0.033
0
0.033
0
0.013
DCON
LF
140
DC(h8)
PL
0
0.022
0
0.022
0
0.009
Type1
LCF
LH
OAL
(Note 2) MWE-SB/MB drills are suitable for use with shrink fit holders.
DRILLING
3.5
3.6
3.7
3.8
a
r
a
r
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
r
a
r
2
2
3
3
2
2
3
3
1
1
18.6 18.6 55.6 55

18.6 20.6 55.6 55
0.6
0.6
3.1
4.0
1
1
24.6 24.6 60.6 60

24.6 26.6 60.6 60
0.6
0.6
3.1
4.0
1
1
18.6 18.6 55.6 55

18.6 20.6 55.6 55
0.6
0.6
3.2
4.0
1
1
24.6 24.6 60.6 60

24.6 26.6 60.6 60
0.6
0.6
3.2
4.0
1
1
18.6 18.6 55.6 55

18.6 20.6 55.6 55
0.6
0.6
3.3
4.0
1
1
24.6 24.6 60.6 60

24.6 26.6 60.6 60
0.6
0.6
3.3
4.0
1
1
20.6 20.6 55.6 55

18.6 20.6 55.6 55
0.6
0.6
3.4
4.0
1
1
24.6 24.6 60.6 60

24.6 26.6 60.6 60
0.6
0.6
3.4
4.0
1
1
20.6 20.6 55.6 55

18.6 20.6 55.6 55
0.6
0.6
3.5
4.0
1
1
24.6 24.6 60.6 60

24.6 26.6 60.6 60
0.6
0.6
3.5
4.0
1
1
20.7 20.7 55.7 55

20.7 20.7 55.7 55
0.7
0.7
3.6
4.0
1
1
27.7 27.7 60.7 60

27.7 27.7 60.7 60
0.7
0.7
3.6
4.0
1
1
20.7 20.7 55.7 55

20.7 20.7 55.7 55
0.7
0.7
3.7
4.0
1
1
27.7 27.7 60.7 60

27.7 27.7 60.7 60
0.7
0.7
3.7
4.0
1
1
22.7 22.7 55.7 55

20.7 20.7 55.7 55
0.7
0.7
3.8
4.0
1
1
27.7 27.7 60.7 60

27.7 27.7 60.7 60
0.7
0.7
3.8
4.0
1
1
3
3
2
2
3
3
2
2
a
r
3
3
MWE0390SA
MWE0390SB
MWE0390MA
MWE0390MB
MWE0400SA
MWE0400SB
MWE0400MA
MWE0400MB
MWE0410SA
MWE0410SB
MWE0410MA
MWE0410MB
MWE0420SA
MWE0420SB
MWE0420MA
MWE0420MB
MWE0430SA
MWE0430SB
MWE0430MA
MWE0430MB
MWE0440SA
MWE0440SB
MWE0440MA
MWE0440MB
MWE0450SA
MWE0450SB
MWE0450MA
MWE0450MB
MWE0460SA
MWE0460SB
MWE0460MA
MWE0460MB
MWE0470SA
MWE0470SB
MWE0470MA
MWE0470MB
3.9
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
a
a
r
3
3
2
2
3
3
a
N054
22.7 22.7 55.7 55

20.7 20.7 55.7 55
0.7
0.7
3.9
4.0
1
1
27.7 27.7 60.7 60

27.7 27.7 60.7 60
0.7
0.7
3.9
4.0
1
1
22.7 22.7 55.7 55

20.7 20.7 55.7 55
0.7
0.7
4.0
4.0
1
1
27.7 27.7 60.7 60

27.7 27.7 60.7 60
0.7
0.7
4.0
4.0
1
1
22.7 22.7 55.7 55

22.7 24.7 62.7 62
0.7
0.7
4.1
5.0
1
1
29.7 29.7 63.7 63

29.7 31.7 68.7 68
0.7
0.7
4.1
5.0
1
1
22.8 22.8 55.8 55

22.8 24.8 62.8 62
0.8
0.8
4.2
5.0
1
1
29.8 29.8 63.8 63

29.8 31.8 68.8 68
0.8
0.8
4.2
5.0
1
1
24.8 24.8 58.8 58

22.8 24.8 62.8 62
0.8
0.8
4.3
5.0
1
1
29.8 29.8 63.8 63

29.8 31.8 68.8 68
0.8
0.8
4.3
5.0
1
1
24.8 24.8 58.8 58

22.8 24.8 62.8 62
0.8
0.8
4.4
5.0
1
1
29.8 29.8 63.8 63

29.8 31.8 68.8 68
0.8
0.8
4.4
5.0
1
1
24.8 24.8 58.8 58

22.8 24.8 62.8 62
0.8
0.8
4.5
5.0
1
1
29.8 29.8 63.8 63

29.8 31.8 68.8 68
0.8
0.8
4.5
5.0
1
1
24.8 24.8 58.8 58

24.8 24.8 62.8 62
0.8
0.8
4.6
5.0
1
1
32.8 32.8 68.8 68

32.8 32.8 68.8 68
0.8
0.8
4.6
5.0
1
1
24.9 24.9 58.9 58

24.9 24.9 62.9 62
0.9
0.9
4.7
5.0
1
1
32.9 32.9 68.9 68

32.9 32.9 68.9 68
0.9
0.9
4.7
5.0
1
1
OAL
3.0
3.0
LH
0.5
0.5
2
2
(mm) (l/d)
LCF
21.5 21.5 60.5 60

21.5 21.5 60.5 60
Hole Depth
1
1
DCON
3.4
3
3
3.0
3.0
Type
PL
3.3
2
2
0.5
0.5
Order Number
LF
3.2
3
3
a
r
16.5 16.5 55.5 55

16.5 16.5 55.5 55
DC
Dimensions (mm)
Stock
VP15TF
3.1
2
2
DCON
PL
3.0
LF
3
3
MWE0300SA
MWE0300SB
MWE0300MA
MWE0300MB
MWE0310SA
MWE0310SB
MWE0310MA
MWE0310MB
MWE0320SA
MWE0320SB
MWE0320MA
MWE0320MB
MWE0330SA
MWE0330SB
MWE0330MA
MWE0330MB
MWE0340SA
MWE0340SB
MWE0340MA
MWE0340MB
MWE0350SA
MWE0350SB
MWE0350MA
MWE0350MB
MWE0360SA
MWE0360SB
MWE0360MA
MWE0360MB
MWE0370SA
MWE0370SB
MWE0370MA
MWE0370MB
MWE0380SA
MWE0380SB
MWE0380MA
MWE0380MB
OAL
LH
2
2
Type
LCF
Order Number
(mm) (l/d)
External Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
External Coolant
Stock
CARBIDE
5.6
5.7
5.8
5.9
3
3
a
r
2
2
3
3
2
2
3
3
2
2
3
3
2
2
a
a
r
3
3
2
2
3
3
a
r
2
2
3
3
2
2
a
a
r
3
3
2
2
3
3
2
2
3
3
2
2
3
3
a
r
4.9
5.0
1
1
32.9 32.9 68.9 68

32.9 32.9 68.9 68
0.9
0.9
4.9
5.0
1
1
26.9 26.9 62.9 62

24.9 24.9 62.9 62
0.9
0.9
5.0
5.0
1
1
32.9 32.9 68.9 68

32.9 32.9 68.9 68
0.9
0.9
5.0
5.0
1
1
26.9 26.9 62.9 62

26.9 28.9 66.9 66
0.9
0.9
5.1
6.0
1
1
34.9 34.9 72.9 72

34.9 36.9 74.9 74
0.9
0.9
5.1
6.0
1
1
26.9 26.9 62.9 62

26.9 28.9 66.9 66
0.9
0.9
5.2
6.0
1
1
34.9 34.9 72.9 72

34.9 36.9 74.9 74
0.9
0.9
5.2
6.0
1
1
27.0 27.0 63.0 62

27.0 29.0 67.0 66
1.0
1.0
5.3
6.0
1
1
35.0 35.0 73.0 72

35.0 37.0 75.0 74
1.0
1.0
5.3
6.0
1
1
29.0 29.0 67.0 66

27.0 29.0 67.0 66
1.0
1.0
5.4
6.0
1
1
35.0 35.0 73.0 72

35.0 37.0 75.0 74
1.0
1.0
5.4
6.0
1
1
29.0 29.0 67.0 66

27.0 29.0 67.0 66
1.0
1.0
5.5
6.0
1
1
35.0 35.0 73.0 72

35.0 37.0 75.0 74
1.0
1.0
5.5
6.0
1
1
29.0 29.0 67.0 66

29.0 29.0 67.0 66
1.0
1.0
5.6
6.0
1
1
37.0 37.0 75.0 74

37.0 37.0 75.0 74
1.0
1.0
5.6
6.0
1
1
29.0 29.0 67.0 66

29.0 29.0 67.0 66
1.0
1.0
5.7
6.0
1
1
37.0 37.0 75.0 74

37.0 37.0 75.0 74
1.0
1.0
5.7
6.0
1
1
29.1 29.1 67.1 66

29.1 29.1 67.1 66
1.1
1.1
5.8
6.0
1
1
37.1 37.1 75.1 74

37.1 37.1 75.1 74
1.1
1.1
5.8
6.0
1
1
29.1 29.1 67.1 66

29.1 29.1 67.1 66
1.1
1.1
5.9
6.0
1
1
37.1 37.1 75.1 74

37.1 37.1 75.1 74
1.1
1.1
5.9
6.0
1
1
6.0
2
2
6.1
3
3
2
2
6.2
3
3
6.3
6.4
6.5
6.6
6.7
6.8
6.9
7.0
7.1
2
2
3
3
2
2
3
3
a
r
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
29.1 29.1 67.1 66

29.1 29.1 67.1 66
1.1
1.1
6.0
6.0
1
1
42.1 42.1 82.1 81

37.1 37.1 75.1 74
1.1
1.1
6.0
6.0
1
1
32.1 32.1 71.1 70

32.1 35.1 75.1 74
1.1
1.1
6.1
7.0
1
1
42.1 42.1 82.1 81

42.1 45.1 84.1 83
1.1
1.1
6.1
7.0
1
1
32.1 32.1 71.1 70

32.1 35.1 75.1 74
1.1
1.1
6.2
7.0
1
1
42.1 42.1 82.1 81

42.1 45.1 84.1 83
1.1
1.1
6.2
7.0
1
1
32.1 32.1 71.1 70

32.1 35.1 75.1 74
1.1
1.1
6.3
7.0
1
1
42.1 42.1 72.1 81

42.1 45.1 84.1 83
1.1
1.1
6.3
7.0
1
1
32.2 32.2 71.2 70

32.2 35.2 75.2 74
1.2
1.2
6.4
7.0
1
1
42.2 42.2 82.2 81

42.2 45.2 84.2 83
1.2
1.2
6.4
7.0
1
1
32.2 32.2 71.2 70

32.2 35.2 75.2 74
1.2
1.2
6.5
7.0
1
1
42.2 42.2 82.2 81

42.2 45.2 84.2 83
1.2
1.2
6.5
7.0
1
1
32.2 32.2 71.2 70

35.2 35.2 75.2 74
1.2
1.2
6.6
7.0
1
1
44.2 44.2 84.2 83

44.2 44.2 84.2 83
1.2
1.2
6.6
7.0
1
1
32.2 32.2 71.2 70

35.2 35.2 75.2 74
1.2
1.2
6.7
7.0
1
1
44.2 44.2 84.2 83

44.2 44.2 84.2 83
1.2
1.2
6.7
7.0
1
1
35.2 35.2 75.2 74

35.2 35.2 75.2 74
1.2
1.2
6.8
7.0
1
1
44.2 44.2 84.2 83

44.2 44.2 84.2 83
1.2
1.2
6.8
7.0
1
1
35.3 35.3 75.3 74

35.3 35.3 75.3 74
1.3
1.3
6.9
7.0
1
1
44.3 44.3 84.3 83

44.3 44.3 84.3 83
1.3
1.3
6.9
7.0
1
1
35.3 35.3 75.3 74

35.3 35.3 75.3 74
1.3
1.3
7.0
7.0
1
1
44.3 44.3 84.3 83

44.3 44.3 84.3 83
1.3
1.3
7.0
7.0
1
1
35.3 35.3 75.3 74

35.3 38.3 80.3 79
1.3
1.3
7.1
8.0
1
1
46.3 46.3 88.3 87

46.3 49.3 91.3 90
1.3
1.3
7.1
8.0
1
1
OAL
0.9
0.9
3
3
MWE0600SA
MWE0600SB
MWE0600MA
MWE0600MB
MWE0610SA
MWE0610SB
MWE0610MA
MWE0610MB
MWE0620SA
MWE0620SB
MWE0620MA
MWE0620MB
MWE0630SA
MWE0630SB
MWE0630MA
MWE0630MB
MWE0640SA
MWE0640SB
MWE0640MA
MWE0640MB
MWE0650SA
MWE0650SB
MWE0650MA
MWE0650MB
MWE0660SA
MWE0660SB
MWE0660MA
MWE0660MB
MWE0670SA
MWE0670SB
MWE0670MA
MWE0670MB
MWE0680SA
MWE0680SB
MWE0680MA
MWE0680MB
MWE0690SA
MWE0690SB
MWE0690MA
MWE0690MB
MWE0700SA
MWE0700SB
MWE0700MA
MWE0700MB
MWE0710SA
MWE0710SB
MWE0710MA
MWE0710MB
LH
26.9 26.9 62.9 62

24.9 24.9 62.9 62
LCF
1
1
Hole Depth
4.8
5.0
OAL
0.9
0.9
LH
32.9 32.9 68.9 68

32.9 32.9 68.9 68
2
2
(mm) (l/d)
OPERATION GUIDANCE
CUTTING CONDITIONS
N061
TECHNICAL DATA
N062
Q001
DRILLING
5.5
1
1
DCON
5.4
2
2
4.8
5.0
Type
PL
5.3
0.9
0.9
Order Number
LF
5.2
3
3
26.9 26.9 62.9 62

24.9 24.9 62.9 62
DC
Dimensions (mm)
Stock
VP15TF
5.1
DCON
5.0
MWE0480SA
MWE0480SB
MWE0480MA
MWE0480MB
MWE0490SA
MWE0490SB
MWE0490MA
MWE0490MB
MWE0500SA
MWE0500SB
MWE0500MA
MWE0500MB
MWE0510SA
MWE0510SB
MWE0510MA
MWE0510MB
MWE0520SA
MWE0520SB
MWE0520MA
MWE0520MB
MWE0530SA
MWE0530SB
MWE0530MA
MWE0530MB
MWE0540SA
MWE0540SB
MWE0540MA
MWE0540MB
MWE0550SA
MWE0550SB
MWE0550MA
MWE0550MB
MWE0560SA
MWE0560SB
MWE0560MA
MWE0560MB
MWE0570SA
MWE0570SB
MWE0570MA
MWE0570MB
MWE0580SA
MWE0580SB
MWE0580MA
MWE0580MB
MWE0590SA
MWE0590SB
MWE0590MA
MWE0590MB
PL
4.9
Type
LF
4.8
2
2
Order Number
LCF
(mm) (l/d)
External Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
External Coolant
Stock
N055
MWE
WSTAR DRILLS
7.6
7.7
7.8
7.9
DRILLING
8.0
8.1
8.2
8.3
a
r
a
r
3
3
2
2
3
3
a
r
2
2
3
3
2
2
3
3
a
a
r
a
r
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
a
a
r
3
3
2
2
3
3
2
2
3
3
a
r
35.3 35.3 75.3 74

35.3 38.3 80.3 79
1.3
1.3
7.3
8.0
1
1
46.3 46.3 88.3 87

46.3 49.3 91.3 90
1.3
1.3
7.3
8.0
1
1
35.3 35.3 75.3 74

35.3 38.3 80.3 79
1.3
1.3
7.4
8.0
1
1
46.3 46.3 88.3 87

46.3 49.3 91.3 90
1.3
1.3
7.4
8.0
1
1
35.4 35.4 75.4 74

35.4 38.4 80.4 79
1.4
1.4
7.5
8.0
1
1
46.4 46.4 88.4 87

46.4 49.4 91.4 90
1.4
1.4
7.5
8.0
1
1
38.4 38.4 80.4 79

38.4 38.4 80.4 79
1.4
1.4
7.6
8.0
1
1
49.4 49.4 91.4 90

49.4 49.4 91.4 90
1.4
1.4
7.6
8.0
1
1
38.4 38.4 80.4 79

38.4 38.4 80.4 79
1.4
1.4
7.7
8.0
1
1
49.4 49.4 91.4 90

49.4 49.4 91.4 90
1.4
1.4
7.7
8.0
1
1
38.4 38.4 80.4 79

38.4 38.4 80.4 79
1.4
1.4
7.8
8.0
1
1
49.4 49.4 91.4 90

49.4 49.4 91.4 90
1.4
1.4
7.8
8.0
1
1
38.4 38.4 80.4 79

38.4 38.4 80.4 79
1.4
1.4
7.9
8.0
1
1
49.4 49.4 91.4 90

49.4 49.4 91.4 90
1.4
1.4
7.9
8.0
1
1
38.5 38.5 80.5 79

38.5 38.5 80.5 79
1.5
1.5
8.0
8.0
1
1
49.5 49.5 91.5 90

49.5 49.5 91.5 90
1.5
1.5
8.0
8.0
1
1
38.5 38.5 80.5 79

38.5 41.5 85.5 84
1.5
1.5
8.1
9.0
1
1
54.5 54.5 97.5 96

54.5 57.5 99.5 98
1.5
1.5
8.1
9.0
1
1
38.5 38.5 80.5 79

38.5 41.5 85.5 84
1.5
1.5
8.2
9.0
1
1
54.5 54.5 97.5 96

54.5 57.5 99.5 98
1.5
1.5
8.2
9.0
1
1
38.5 38.5 80.5 79

38.5 41.5 85.5 84
1.5
1.5
8.3
9.0
1
1
54.5 54.5 97.5 96

54.5 57.5 99.5 98
1.5
1.5
8.3
9.0
1
1
8.4
2
2
8.5
3
3
2
2
8.6
3
3
2
2
a
r
8.7
3
3
2
2
8.8
8.9
9.0
9.1
9.2
9.3
9.4
9.5
3
3
2
2
3
3
2
2
3
3
2
2
a
r
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
N056
DCON
1
1
MWE0840SA
MWE0840SB
MWE0840MA
MWE0840MB
MWE0850SA
MWE0850SB
MWE0850MA
MWE0850MB
MWE0860SA
MWE0860SB
MWE0860MA
MWE0860MB
MWE0870SA
MWE0870SB
MWE0870MA
MWE0870MB
MWE0880SA
MWE0880SB
MWE0880MA
MWE0880MB
MWE0890SA
MWE0890SB
MWE0890MA
MWE0890MB
MWE0900SA
MWE0900SB
MWE0900MA
MWE0900MB
MWE0910SA
MWE0910SB
MWE0910MA
MWE0910MB
MWE0920SA
MWE0920SB
MWE0920MA
MWE0920MB
MWE0930SA
MWE0930SB
MWE0930MA
MWE0930MB
MWE0940SA
MWE0940SB
MWE0940MA
MWE0940MB
MWE0950SA
MWE0950SB
MWE0950MA
MWE0950MB
PL
7.2
8.0
LF
1.3
1.3
2
2
(mm) (l/d)
OAL
46.3 46.3 88.3 87

46.3 49.3 91.3 90
Order Number
LH
1
1
Hole Depth
7.2
8.0
OAL
1.3
1.3
LH
35.3 35.3 75.3 74

35.3 38.3 80.3 79
DC
Dimensions (mm)
Stock
VP15TF
7.5
DCON
7.4
2
2
MWE0720SA
MWE0720SB
MWE0720MA
MWE0720MB
MWE0730SA
MWE0730SB
MWE0730MA
MWE0730MB
MWE0740SA
MWE0740SB
MWE0740MA
MWE0740MB
MWE0750SA
MWE0750SB
MWE0750MA
MWE0750MB
MWE0760SA
MWE0760SB
MWE0760MA
MWE0760MB
MWE0770SA
MWE0770SB
MWE0770MA
MWE0770MB
MWE0780SA
MWE0780SB
MWE0780MA
MWE0780MB
MWE0790SA
MWE0790SB
MWE0790MA
MWE0790MB
MWE0800SA
MWE0800SB
MWE0800MA
MWE0800MB
MWE0810SA
MWE0810SB
MWE0810MA
MWE0810MB
MWE0820SA
MWE0820SB
MWE0820MA
MWE0820MB
MWE0830SA
MWE0830SB
MWE0830MA
MWE0830MB
PL
7.3
3
3
Type
LF
7.2
2
2
Order Number
LCF
(mm) (l/d)
External Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
External Coolant
Stock
LCF
CARBIDE
Type
38.5 38.5 80.5 79 1.5

38.5 41.5 85.5 84 1.5
8.4 1
9.0 1
54.5 54.5 97.5 96 1.5
8.4 1
54.5 57.5 99.5 98 1.5
9.0 1
38.5 38.5 80.5 79 1.5

38.5 41.5 85.5 84 1.5
8.5 1
9.0 1
54.5 54.5 97.5 96 1.5

54.5 57.5 99.5 98 1.5
8.5 1
9.0 1
41.6 41.6 85.6 84 1.6

41.6 41.6 85.6 84 1.6
8.6 1
9.0 1
56.6 56.6 99.6 98 1.6

56.6 56.6 99.6 98 1.6
8.6 1
9.0 1
41.6 41.6 85.6 84 1.6

41.6 41.6 85.6 84 1.6
8.7 1
9.0 1
56.6 56.6 99.6 98 1.6

56.6 56.6 99.6 98 1.6
8.7 1
9.0 1
41.6 41.6 85.6 84 1.6

41.6 41.6 85.6 84 1.6
8.8 1
9.0 1
56.6 56.6 99.6 98 1.6

56.6 56.6 99.6 98 1.6
8.8 1
9.0 1
41.6 41.6 85.6 84 1.6

41.6 41.6 85.6 84 1.6
8.9 1
9.0 1
56.6 56.6 99.6 98 1.6

56.6 56.6 99.6 98 1.6
8.9 1
9.0 1
41.6 41.6 85.6 84 1.6

41.6 41.6 85.6 84 1.6
9.0 1
9.0 1
56.6 56.6 99.6 98 1.6

56.6 56.6 99.6 98 1.6
9.0 1
9.0 1
41.7 41.7 85.7 84 1.7 9.1 1

41.7 44.7 90.7 89 1.7 10.0 1
59.7 59.7 103.7 102 1.7 9.1 1
59.7 62.7 106.7 105 1.7 10.0 1
41.7 41.7 85.7 84 1.7 9.2 1
41.7 44.7 90.7 89 1.7 10.0 1
59.7 59.7 103.7 102 1.7 9.2 1
59.7 62.7 106.7 105 1.7 10.0 1
41.7 41.7 82.7 84 1.7 9.3 1
41.7 44.7 90.7 89 1.7 10.0 1
59.7 59.7 103.7 102 1.7 9.3 1
59.7 62.7 106.7 105 1.7 10.0 1
41.7 41.7 85.7 84 1.7 9.4 1
41.7 44.7 90.7 89 1.7 10.0 1
59.7 59.7 103.7 102 1.7 9.4 1
59.7 62.7 106.7 105 1.7 10.0 1
41.7 41.7 85.7 84 1.7 9.5 1
41.7 44.7 90.7 89 1.7 10.0 1
59.7 59.7 103.7 102 1.7 9.5 1
59.7 62.7 106.7 105 1.7 10.0 1
CARBIDE
9.8
9.9
10.0
10.1
10.2
10.3
10.4
10.5
10.6
10.7
a
r
3
3
2
2
3
3
2
2
3
3
a
r
2
2
3
3
2
2
3
3
a
a
r
a
r
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
a
a
r
3
3
2
2
3
3
a
r
61.7 61.7 106.7 105 1.7 9.6 1

61.7 61.7 106.7 105 1.7 10.0 1
44.8 44.8 90.8 89 1.8 9.7 1
44.8 44.8 90.8 89 1.8 10.0 1
61.8 61.8 106.8 105 1.8 9.7 1
61.8 61.8 106.8 105 1.8 10.0 1
44.8 44.8 90.8 89 1.8 9.8 1
44.8 44.8 90.8 89 1.8 10.0 1
61.8 61.8 106.8 105 1.8 9.8 1
61.8 61.8 106.8 105 1.8 10.0 1
44.8 44.8 90.8 89 1.8 9.9 1
44.8 44.8 90.8 89 1.8 10.0 1
61.8 61.8 106.8 105 1.8 9.9 1
61.8 61.8 106.8 105 1.8 10.0 1
44.8 44.8 90.8 89 1.8 10.0 1
44.8 44.8 90.8 89 1.8 10.0 1
61.8 61.8 106.8 105 1.8 10.0 1
61.8 61.8 106.8 105 1.8 10.0 1
44.8 44.8 90.8 89 1.8 10.1 1
44.8 47.8 96.8 95 1.8 11.0 1
67.8 67.8 113.8 112 1.8 10.1 1
67.8 70.8 115.8 114 1.8 11.0 1
44.9 44.9 90.9 89 1.9 10.2 1
44.9 47.9 96.9 95 1.9 11.0 1
67.9 67.9 113.9 112 1.9 10.2 1
67.9 70.9 115.9 114 1.9 11.0 1
44.9 44.9 90.9 89 1.9 10.3 1
44.9 47.9 96.9 95 1.9 11.0 1
67.9 67.9 113.9 112 1.9 10.3 1
67.9 70.9 115.9 114 1.9 11.0 1
44.9 44.9 90.9 89 1.9 10.4 1
44.9 47.9 96.9 95 1.9 11.0 1
67.9 67.9 113.9 112 1.9 10.4 1
67.9 70.9 115.9 114 1.9 11.0 1
44.9 44.9 90.9 89 1.9 10.5 1
44.9 47.9 96.9 95 1.9 11.0 1
67.9 67.9 113.9 112 1.9 10.5 1
67.9 70.9 115.9 114 1.9 11.0 1
44.9 44.9 90.9 89 1.9 10.6 1
48.9 48.9 96.9 95 1.9 11.0 1
69.9 69.9 115.9 114 1.9 10.6 1
69.9 69.9 115.9 114 1.9 11.0 1
48.9 48.9 96.9 95 1.9 10.7 1
48.9 48.9 96.9 95 1.9 11.0 1
69.9 69.9 115.9 114 1.9 10.7 1
69.9 69.9 115.9 114 1.9 11.0 1
10.8
10.9
11.0
11.1
11.2
11.3
11.4
11.5
11.6
11.7
11.8
11.9
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
a
a
r
3
3
2
2
3
3
2
2
3
3
2
2
3
3
DCON
PL
LF
MWE1080SA
MWE1080SB
MWE1080MA
MWE1080MB
MWE1090SA
MWE1090SB
MWE1090MA
MWE1090MB
MWE1100SA
MWE1100SB
MWE1100MA
MWE1100MB
MWE1110SA
MWE1110SB
MWE1110MA
MWE1110MB
MWE1120SA
MWE1120SB
MWE1120MA
MWE1120MB
MWE1130SA
MWE1130SB
MWE1130MA
MWE1130MB
MWE1140SA
MWE1140SB
MWE1140MA
MWE1140MB
MWE1150SA
MWE1150SB
MWE1150MA
MWE1150MB
MWE1160SA
MWE1160SB
MWE1160MA
MWE1160MB
MWE1170SA
MWE1170SB
MWE1170MA
MWE1170MB
MWE1180SA
MWE1180SB
MWE1180MA
MWE1180MB
MWE1190SA
MWE1190SB
MWE1190MA
MWE1190MB
OAL
a
r
LH
(mm) (l/d)
Order Number
LCF
Hole Depth
DCON
44.7 44.7 90.7 89 1.7 9.6 1

44.7 44.7 90.7 89 1.7 10.0 1
DC
Type
49.0 49.0 97.0 95 2.0 10.8 1

49.0 49.0 97.0 95 2.0 11.0 1
70.0 70.0 116.0 114 2.0 10.8 1
70.0 70.0 116.0 114 2.0 11.0 1
49.0 49.0 97.0 95 2.0 10.9 1
49.0 49.0 97.0 95 2.0 11.0 1
70.0 70.0 116.0 114 2.0 10.9 1
70.0 70.0 116.0 114 2.0 11.0 1
49.0 49.0 97.0 95 2.0 11.0 1
49.0 49.0 97.0 95 2.0 11.0 1
70.0 70.0 116.0 114 2.0 11.0 1
70.0 70.0 116.0 114 2.0 11.0 1
49.0 49.0 97.0 95 2.0 11.1 1
49.0 52.0 97.0 95 2.0 12.0 1
73.0 73.0 120.0 118 2.0 11.1 1
73.0 76.0 123.0 121 2.0 12.0 1
49.0 49.0 97.0 95 2.0 11.2 1
49.0 52.0 97.0 95 2.0 12.0 1
73.0 73.0 120.0 118 2.0 11.2 1
73.0 76.0 123.0 121 2.0 12.0 1
49.1 49.1 97.1 95 2.1 11.3 1
49.1 52.1 97.1 95 2.1 12.0 1
73.1 73.1 120.1 118 2.1 11.3 1
73.1 76.1 123.1 121 2.1 12.0 1
49.1 49.1 97.1 95 2.1 11.4 1
49.1 52.1 97.1 95 2.1 12.0 1
73.1 73.1 120.1 118 2.1 11.4 1
73.1 76.1 123.1 121 2.1 12.0 1
49.1 49.1 97.1 95 2.1 11.5 1
49.1 52.1 97.1 95 2.1 12.0 1
73.1 73.1 120.1 118 2.1 11.5 1
73.1 76.1 123.1 121 2.1 12.0 1
49.1 49.1 97.1 95 2.1 11.6 1
49.1 49.1 97.1 95 2.1 12.0 1
75.1 75.1 123.1 121 2.1 11.6 1
75.1 75.1 123.1 121 2.1 12.0 1
49.1 49.1 97.1 95 2.1 11.7 1
49.1 49.1 97.1 95 2.1 12.0 1
75.1 75.1 123.1 121 2.1 11.7 1
75.1 75.1 123.1 121 2.1 12.0 1
49.1 49.1 97.1 95 2.1 11.8 1
49.1 49.1 97.1 95 2.1 12.0 1
DRILLING
9.7
2
2
PL
Type
Dimensions (mm)
Stock
VP15TF
9.6
LF
3
3
MWE0960SA
MWE0960SB
MWE0960MA
MWE0960MB
MWE0970SA
MWE0970SB
MWE0970MA
MWE0970MB
MWE0980SA
MWE0980SB
MWE0980MA
MWE0980MB
MWE0990SA
MWE0990SB
MWE0990MA
MWE0990MB
MWE1000SA
MWE1000SB
MWE1000MA
MWE1000MB
MWE1010SA
MWE1010SB
MWE1010MA
MWE1010MB
MWE1020SA
MWE1020SB
MWE1020MA
MWE1020MB
MWE1030SA
MWE1030SB
MWE1030MA
MWE1030MB
MWE1040SA
MWE1040SB
MWE1040MA
MWE1040MB
MWE1050SA
MWE1050SB
MWE1050MA
MWE1050MB
MWE1060SA
MWE1060SB
MWE1060MA
MWE1060MB
MWE1070SA
MWE1070SB
MWE1070MA
MWE1070MB
OAL
LH
2
2
LCF
Order Number
(mm) (l/d)
External Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
External Coolant
Stock
75.1 75.1 123.1 121 2.1 11.8 1

75.1 75.1 123.1 121 2.1 12.0 1
53.2 53.2 104.2 102 2.2 11.9 1
49.2 49.2 97.2 95 2.2 12.0 1
75.2 75.2 123.2 121 2.2 11.9 1
75.2 75.2 123.2 121 2.2 12.0 1
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N061
N062
Q001
N057
MWE
WSTAR DRILLS
12.1
12.2
12.3
12.4
12.5
12.6
12.7
DRILLING
12.8
12.9
13.0
13.1
2
2
a
a
r
3
3
2
2
3
3
2
2
3
3
a
r
2
2
3
3
2
2
a
a
r
3
3
2
2
3
3
2
2
3
3
2
2
3
3
a
r
2
2
3
3
2
2
3
3
a
a
r
a
r
53.2 53.2 104.2 102 2.2 12.1 1

53.2 56.2 104.2 102 2.2 13.0 1
78.2 78.2 137.2 135 2.2 12.1 1
78.2 81.2 139.2 137 2.2 13.0 1
53.2 53.2 104.2 102 2.2 12.2 1
53.2 56.2 104.2 102 2.2 13.0 1
78.2 78.2 137.2 135 2.2 12.2 1
78.2 81.2 139.2 137 2.2 13.0 1
53.2 53.2 104.2 102 2.2 12.3 1
53.2 56.2 104.2 102 2.2 13.0 1
78.2 78.2 137.2 135 2.2 12.3 1
78.2 81.2 139.2 137 2.2 13.0 1
53.3 53.3 104.3 102 2.3 12.4 1
53.3 56.3 104.3 102 2.3 13.0 1
78.3 78.3 137.3 135 2.3 12.4 1
78.3 81.3 139.3 137 2.3 13.0 1
53.3 53.3 104.3 102 2.3 12.5 1
53.3 56.3 104.3 102 2.3 13.0 1
78.3 78.3 137.3 135 2.3 12.5 1
78.3 81.3 139.3 137 2.3 13.0 1
53.3 53.3 104.3 102 2.3 12.6 1
53.3 53.3 104.3 102 2.3 13.0 1
80.3 80.3 139.3 137 2.3 12.6 1
80.3 80.3 139.3 137 2.3 13.0 1
53.3 53.3 104.3 102 2.3 12.7 1
53.3 53.3 104.3 102 2.3 13.0 1
80.3 80.3 139.3 137 2.3 12.7 1
80.3 80.3 139.3 137 2.3 13.0 1
53.3 53.3 104.3 102 2.3 12.8 1
53.3 53.3 104.3 102 2.3 13.0 1
80.3 80.3 139.3 137 2.3 12.8 1
80.3 80.3 139.3 137 2.3 13.0 1
53.3 53.3 104.3 102 2.3 12.9 1
53.3 53.3 104.3 102 2.3 13.0 1
80.3 80.3 139.3 137 2.3 12.9 1
80.3 80.3 139.3 137 2.3 13.0 1
53.4 53.4 104.4 102 2.4 13.0 1
53.4 53.4 104.4 102 2.4 13.0 1
80.4 80.4 139.4 137 2.4 13.0 1
80.4 80.4 139.4 137 2.4 13.0 1
53.4 53.4 104.4 102 2.4 13.1 1
56.4 59.4 109.4 107 2.4 14.0 1
86.4 86.4 146.4 144 2.4 13.1 1
86.4 89.4 149.4 147 2.4 14.0 1
13.2
13.3
13.4
13.5
13.6
13.7
13.8
13.9
14.0
14.1
14.2
14.3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
a
a
r
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
r
r
a
r
N058
DCON
PL
MWE1320SA
MWE1320SB
MWE1320MA
MWE1320MB
MWE1330SA
MWE1330SB
MWE1330MA
MWE1330MB
MWE1340SA
MWE1340SB
MWE1340MA
MWE1340MB
MWE1350SA
MWE1350SB
MWE1350MA
MWE1350MB
MWE1360SA
MWE1360SB
MWE1360MA
MWE1360MB
MWE1370SA
MWE1370SB
MWE1370MA
MWE1370MB
MWE1380SA
MWE1380SB
MWE1380MA
MWE1380MB
MWE1390SA
MWE1390SB
MWE1390MA
MWE1390MB
MWE1400SA
MWE1400SB
MWE1400MA
MWE1400MB
MWE1410SA
MWE1410SB
MWE1410MA
MWE1410MB
MWE1420SA
MWE1420SB
MWE1420MA
MWE1420MB
MWE1430SA
MWE1430SB
MWE1430MA
MWE1430MB
LF
a
r
OAL
75.2 75.2 123.2 121 2.2 12.0 1

75.2 75.2 123.2 121 2.2 12.0 1
(mm) (l/d)
Order Number
LH
3
3
53.2 53.2 104.2 102 2.2 12.0 1

49.2 49.2 97.2 95 2.2 12.0 1
DC
Hole Depth
DCON
2
2
PL
Type
Dimensions (mm)
Stock
VP15TF
12.0
LF
3
3
MWE1200SA
MWE1200SB
MWE1200MA
MWE1200MB
MWE1210SA
MWE1210SB
MWE1210MA
MWE1210MB
MWE1220SA
MWE1220SB
MWE1220MA
MWE1220MB
MWE1230SA
MWE1230SB
MWE1230MA
MWE1230MB
MWE1240SA
MWE1240SB
MWE1240MA
MWE1240MB
MWE1250SA
MWE1250SB
MWE1250MA
MWE1250MB
MWE1260SA
MWE1260SB
MWE1260MA
MWE1260MB
MWE1270SA
MWE1270SB
MWE1270MA
MWE1270MB
MWE1280SA
MWE1280SB
MWE1280MA
MWE1280MB
MWE1290SA
MWE1290SB
MWE1290MA
MWE1290MB
MWE1300SA
MWE1300SB
MWE1300MA
MWE1300MB
MWE1310SA
MWE1310SB
MWE1310MA
MWE1310MB
OAL
LH
2
2
LCF
Order Number
(mm) (l/d)
External Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
External Coolant
Stock
LCF
CARBIDE
Type
53.4 53.4 104.4 102 2.4 13.2 1

56.4 59.4 109.4 107 2.4 14.0 1
86.4 86.4 146.4 144 2.4 13.2 1
86.4 89.4 149.4 147 2.4 14.0 1
56.4 56.4 109.4 107 2.4 13.3 1
56.4 59.4 109.4 107 2.4 14.0 1
86.4 86.4 146.4 144 2.4 13.3 1
86.4 89.4 149.4 147 2.4 14.0 1
56.4 56.4 109.4 107 2.4 13.4 1
56.4 59.4 109.4 107 2.4 14.0 1
86.4 86.4 146.4 144 2.4 13.4 1
86.4 89.4 149.4 147 2.4 14.0 1
56.5 56.5 109.5 107 2.5 13.5 1
56.5 59.5 109.5 107 2.5 14.0 1
86.5 86.5 146.5 144 2.5 13.5 1
86.5 89.5 149.5 147 2.5 14.0 1
56.5 56.5 109.5 107 2.5 13.6 1
56.5 56.5 109.5 107 2.5 14.0 1
88.5 88.5 149.5 147 2.5 13.6 1
88.5 88.5 149.5 147 2.5 14.0 1
56.5 56.5 109.5 107 2.5 13.7 1
56.5 56.5 109.5 107 2.5 14.0 1
88.5 88.5 149.5 147 2.5 13.7 1
88.5 88.5 149.5 147 2.5 14.0 1
56.5 56.5 109.5 107 2.5 13.8 1
56.5 56.5 109.5 107 2.5 14.0 1
88.5 88.5 149.5 147 2.5 13.8 1
88.5 88.5 149.5 147 2.5 14.0 1
56.5 56.5 109.5 107 2.5 13.9 1
56.5 56.5 109.5 107 2.5 14.0 1
88.5 88.5 149.5 147 2.5 13.9 1
88.5 88.5 149.5 147 2.5 14.0 1
56.5 56.5 109.5 107 2.5 14.0 1
56.5 56.5 109.5 107 2.5 14.0 1
88.5 88.5 149.5 147 2.5 14.0 1
88.5 88.5 149.5 147 2.5 14.0 1
58.6 58.6 113.6 111
58.6 61.6 113.6 111
2.6 14.1 1
2.6 15.0 1
91.6 91.6 153.6 151 2.6 14.1 1

91.6 94.6 155.6 153 2.6 15.0 1
58.6 58.6 113.6 111
58.6 61.6 113.6 111
2.6 14.2 1
2.6 15.0 1
91.6 91.6 153.6 151 2.6 14.2 1

91.6 94.6 155.6 153 2.6 15.0 1
58.6 58.6 113.6 111
58.6 61.6 113.6 111
2.6 14.3 1
2.6 15.0 1
91.6 91.6 153.6 151 2.6 14.3 1

91.6 94.6 155.6 153 2.6 15.0 1
CARBIDE
14.6
14.7
14.8
14.9
15.0
15.1
15.2
15.3
15.4
15.5
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
r
r
r
a
r
2
2
3
3
2
2
3
3
2
2
3
3
2
2
3
3
a
r
r
r
a
r
2
2
3
3
2
2
3
3
2.6 14.4 1
58.6 61.6 113.6 111
2.6 15.0 1
91.6 91.6 153.6 151 2.6 14.4 1

91.6 94.6 155.6 153 2.6 15.0 1
58.6 58.6 113.6 111
58.6 61.6 113.6 111
2.6 14.5 1
2.6 15.0 1
91.6 91.6 153.6 151 2.6 14.5 1

91.6 94.6 155.6 153 2.6 15.0 1
58.7 58.7 113.7 111
58.7 58.7 113.7 111
2.7 14.6 1
2.7 15.0 1
93.7 93.7 155.7 153 2.7 14.6 1

93.7 93.7 155.7 153 2.7 15.0 1
58.7 58.7 113.7 111
58.7 58.7 113.7 111
2.7 14.7 1
2.7 15.0 1
93.7 93.7 155.7 153 2.7 14.7 1

93.7 93.7 155.7 153 2.7 15.0 1
58.7 58.7 113.7 111
58.7 58.7 113.7 111
2.7 14.8 1
2.7 15.0 1
93.7 93.7 155.7 153 2.7 14.8 1

93.7 93.7 155.7 153 2.7 15.0 1
15.6
15.7
15.8
15.9
16.0
3
3
2
2
3
3
2
2
3
3
r
a
r
r
r
a
r
r
r
a
r
2
2
3
3
2.7 14.9 1
2.7 15.0 1
16.1
2
3
93.7 93.7 155.7 153 2.7 14.9 1

93.7 93.7 155.7 153 2.7 15.0 1
16.2
2
3
58.7 58.7 113.7 111

58.7 58.7 113.7 111
2.7 15.0 1
2.7 15.0 1
16.3
2
3
93.7 93.7 155.7 153 2.7 15.0 1

93.7 93.7 155.7 153 2.7 15.0 1
16.4
2
3
60.7 60.7 117.7 115 2.7 15.1 1

60.7 63.7 117.7 115 2.7 16.0 1
16.5
2
3
96.7 96.7 159.7 157 2.7 15.1 1

96.7 99.7 162.7 160 2.7 16.0 1
16.6
2
3
60.8 60.8 117.8 115 2.8 15.2 1

60.8 63.8 117.8 115 2.8 16.0 1
16.7
2
3
96.8 96.8 159.8 157 2.8 15.2 1

96.8 99.8 162.8 160 2.8 16.0 1
16.8
2
3
60.8 60.8 117.8 115 2.8 15.3 1

60.8 63.8 117.8 115 2.8 16.0 1
16.9
2
3
96.8 96.8 159.8 157 2.8 15.3 1

96.8 99.8 162.8 160 2.8 16.0 1
17.0
2
3
60.8 60.8 117.8 115 2.8 15.4 1

60.8 63.8 117.8 115 2.8 16.0 1
17.1
2
3
96.8 96.8 159.8 157 2.8 15.4 1

96.8 99.8 162.8 160 2.8 16.0 1
17.2
2
3
60.8 60.8 117.8 115 2.8 15.5 1

60.8 63.8 117.8 115 2.8 16.0 1
17.3
2
3
96.8 96.8 159.8 157 2.8 15.5 1

96.8 99.8 162.8 160 2.8 16.0 1
17.4
2
3
58.7 58.7 113.7 111

58.7 58.7 113.7 111
r
a
DCON
2
2
PL
LF
3
3
MWE1560SA
MWE1560SB
MWE1560MA
MWE1560MB
MWE1570SA
MWE1570SB
MWE1570MA
MWE1570MB
MWE1580SA
MWE1580SB
MWE1580MA
MWE1580MB
MWE1590SA
MWE1590SB
MWE1590MA
MWE1590MB
MWE1600SA
MWE1600SB
MWE1600MA
MWE1600MB
MWE1610SA
MWE1610MA
MWE1620SA
MWE1620MA
MWE1630SA
MWE1630MA
MWE1640SA
MWE1640MA
MWE1650SA
MWE1650MA
MWE1660SA
MWE1660MA
MWE1670SA
MWE1670MA
MWE1680SA
MWE1680MA
MWE1690SA
MWE1690MA
MWE1700SA
MWE1700MA
MWE1710SA
MWE1710MA
MWE1720SA
MWE1720MA
MWE1730SA
MWE1730MA
MWE1740SA
MWE1740MA
OAL
LH
2
2
(mm) (l/d)
LCF
Order Number
Type
60.8 60.8 117.8 115 2.8 15.6 1

60.8 60.8 117.8 115 2.8 16.0 1
98.8 98.8 162.8 160 2.8 15.6 1
98.8 98.8 162.8 160 2.8 16.0 1
60.9 60.9 117.9 115 2.9 15.7 1
60.9 60.9 117.9 115 2.9 16.0 1
98.9 98.9 162.9 160 2.9 15.7 1
98.9 98.9 162.9 160 2.9 16.0 1
60.9 60.9 117.9 115 2.9 15.8 1
60.9 60.9 117.9 115 2.9 16.0 1
98.9 98.9 162.9 160 2.9 15.8 1
98.9 98.9 162.9 160 2.9 16.0 1
60.9 60.9 117.9 115 2.9 15.9 1
60.9 60.9 117.9 115 2.9 16.0 1
98.9 98.9 162.9 160 2.9 15.9 1
98.9 98.9 162.9 160 2.9 16.0 1
60.9 60.9 117.9 115 2.9 16.0 1
60.9 60.9 117.9 115 2.9 16.0 1
98.9 98.9 162.9 160 2.9 16.0 1
98.9 98.9 162.9 160 2.9 16.0 1
62.9 62.9 121.9 119 2.9 16.1 1
104.9 104.9 169.9 167 2.9 16.1 1
62.9 62.9 121.9 119 2.9 16.2 1
104.9 104.9 169.9 167 2.9 16.2 1
63.0 63.0 122.0 119 3.0 16.3 1
105.0 105.0 170.0 167 3.0 16.3 1
63.0 63.0 122.0 119 3.0 16.4 1
105.0 105.0 170.0 167 3.0 16.4 1
63.0 63.0 122.0 119 3.0 16.5 1
105.0 105.0 170.0 167 3.0 16.5 1
63.0 63.0 122.0 119 3.0 16.6 1
105.0 105.0 170.0 167 3.0 16.6 1
63.0 63.0 122.0 119 3.0 16.7 1
105.0 105.0 170.0 167 3.0 16.7 1
63.1 63.1 122.1 119 3.1 16.8 1
105.1 105.1 170.1 167 3.1 16.8 1
63.1 63.1 122.1 119 3.1 16.9 1
105.1 105.1 170.1 167 3.1 16.9 1
63.1 63.1 122.1 119 3.1 17.0 1
105.1 105.1 170.1 167 3.1 17.0 1
65.1 65.1 126.1 123 3.1 17.1 1
105.1 105.1 170.1 167 3.1 17.1 1
DRILLING
14.5
58.6 58.6 113.6 111
DC
Hole Depth
DCON
3
3
Type
Dimensions (mm)
Stock
VP15TF
14.4
PL
LF
MWE1440SA
MWE1440SB
MWE1440MA
MWE1440MB
MWE1450SA
MWE1450SB
MWE1450MA
MWE1450MB
MWE1460SA
MWE1460SB
MWE1460MA
MWE1460MB
MWE1470SA
MWE1470SB
MWE1470MA
MWE1470MB
MWE1480SA
MWE1480SB
MWE1480MA
MWE1480MB
MWE1490SA
MWE1490SB
MWE1490MA
MWE1490MB
MWE1500SA
MWE1500SB
MWE1500MA
MWE1500MB
MWE1510SA
MWE1510SB
MWE1510MA
MWE1510MB
MWE1520SA
MWE1520SB
MWE1520MA
MWE1520MB
MWE1530SA
MWE1530SB
MWE1530MA
MWE1530MB
MWE1540SA
MWE1540SB
MWE1540MA
MWE1540MB
MWE1550SA
MWE1550SB
MWE1550MA
MWE1550MB
OAL
LH
LCF
Order Number
(mm) (l/d)
External Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
External Coolant
Stock
65.1 65.1 126.1 123 3.1 17.2 1

105.1 105.1 170.1 167 3.1 17.2 1
65.1 65.1 126.1 123 3.1 17.3 1
105.1 105.1 170.1 167 3.1 17.3 1
65.2 65.2 126.2 123 3.2 17.4 1
105.2 105.2 170.2 167 3.2 17.4 1
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N061
N062
Q001
N059
MWE
WSTAR DRILLS
DRILLING
18.0
2
3
18.1
2
3
18.2
2
3
18.3
2
3
18.4
2
3
18.5
2
3
18.6
2
3
18.7
2
3
18.8
2
3
18.9
2
3
19.0
2
3
19.1
2
3
19.2
2
3
19.3
2
3
19.4
2
3
19.5
2
3
19.6
2
3
19.7
2
3
19.8
2
3
65.2 65.2 126.2 123 3.2 17.6 1

105.2 105.2 170.2 167 3.2 17.6 1
20.0
2
3
MWE1990SA 69.6 69.6 134.6

MWE1990MA 117.6 117.6 182.6
MWE2000SA 69.6 69.6 134.6
MWE2000MA 117.6 117.6 182.6
65.2 65.2 126.2 123 3.2 17.7 1

105.2 105.2 170.2 167 3.2 17.7 1
65.2 65.2 126.2 123 3.2 17.8 1
105.2 105.2 170.2 167 3.2 17.8 1
65.3 65.3 126.3 123 3.3 17.9 1
105.3 105.3 170.3 167 3.3 17.9 1
65.3 65.3 126.3 123 3.3 18.0 1
105.3 105.3 170.3 167 3.3 18.0 1
67.3 67.3 130.3 127 3.3 18.1 1
117.3 117.3 182.3 179 3.3 18.1 1
67.3 67.3 130.3 127 3.3 18.2 1
117.3 117.3 182.3 179 3.3 18.2 1
67.3 67.3 130.3 127 3.3 18.3 1
117.3 117.3 182.3 179 3.3 18.3 1
67.3 67.3 130.3 127 3.3 18.4 1
117.3 117.3 182.3 179 3.3 18.4 1
67.4 67.4 130.4 127 3.4 18.5 1
117.4 117.4 182.4 179 3.4 18.5 1
67.4 67.4 130.4 127 3.4 18.6 1
117.4 117.4 182.4 179 3.4 18.6 1
67.4 67.4 130.4 127 3.4 18.7 1
117.4 117.4 182.4 179 3.4 18.7 1
67.4 67.4 130.4 127 3.4 18.8 1
117.4 117.4 182.4 179 3.4 18.8 1
67.4 67.4 130.4 127 3.4 18.9 1
117.4 117.4 182.4 179 3.4 18.9 1
67.5 67.5 130.5 127 3.5 19.0 1
117.5 117.5 182.5 179 3.5 19.0 1
69.5 69.5 134.5 131 3.5 19.1 1
117.5 117.5 182.5 179 3.5 19.1 1
69.5 69.5 134.5 131 3.5 19.2 1
117.5 117.5 182.5 179 3.5 19.2 1
69.5 69.5 134.5 131 3.5 19.3 1
117.5 117.5 182.5 179 3.5 19.3 1
69.5 69.5 134.5 131 3.5 19.4 1
117.5 117.5 182.5 179 3.5 19.4 1
69.5 69.5 134.5 131 3.5 19.5 1
117.5 117.5 182.5 179 3.5 19.5 1
69.6 69.6 134.6 131 3.6 19.6 1
117.6 117.6 182.6 179 3.6 19.6 1
69.6 69.6 134.6 131 3.6 19.7 1
117.6 117.6 182.6 179 3.6 19.7 1
69.6 69.6 134.6 131 3.6 19.8 1
117.6 117.6 182.6 179 3.6 19.8 1
N060
DCON
2
3
PL
17.9
a
r
2
3
LF
2
3
19.9
OAL
17.8
(mm) (l/d)
65.2 65.2 126.2 123 3.2 17.5 1

105.2 105.2 170.2 167 3.2 17.5 1
Order Number
LH
DC
Dimensions (mm)
Stock
VP15TF
2
3
Type
Hole Depth
17.7
DCON
PL
2
3
LF
17.6
MWE1750SA
MWE1750MA
MWE1760SA
MWE1760MA
MWE1770SA
MWE1770MA
MWE1780SA
MWE1780MA
MWE1790SA
MWE1790MA
MWE1800SA
MWE1800MA
MWE1810SA
MWE1810MA
MWE1820SA
MWE1820MA
MWE1830SA
MWE1830MA
MWE1840SA
MWE1840MA
MWE1850SA
MWE1850MA
MWE1860SA
MWE1860MA
MWE1870SA
MWE1870MA
MWE1880SA
MWE1880MA
MWE1890SA
MWE1890MA
MWE1900SA
MWE1900MA
MWE1910SA
MWE1910MA
MWE1920SA
MWE1920MA
MWE1930SA
MWE1930MA
MWE1940SA
MWE1940MA
MWE1950SA
MWE1950MA
MWE1960SA
MWE1960MA
MWE1970SA
MWE1970MA
MWE1980SA
MWE1980MA
OAL
LCF
2
17.5
3
LH
Dimensions (mm)
Order Number
(mm) (l/d)
External Coolant
Stock
VP15TF
DC
Hole Depth
External Coolant
LCF
CARBIDE
Type
131 3.6 19.9 1

179 3.6 19.9 1
131 3.6 20.0 1
179 3.6 20.0 1
CARBIDE

AISI 1010 etc
AISI 4340 etc
Drill Dia.
DC
(mm)
Revolution
(min-1)
3.0
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
6400
5500
4400
4000
3300
2800
2500
1900
1500
Work
Material
Feed rate
(Min.Max.)
(mm/rev)
0.1
0.12
0.15
0.2
0.23
0.27
0.31
0.33
0.35
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
Feed rate
(Min.Max.)
(mm/rev)
Revolution
(min-1)
5900
5100
4100
3700
3100
2700
2300
1700
1400
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
0.1
0.12
0.15
0.2
0.23
0.27
0.31
0.33
0.35
Feed rate
(Min.Max.)
(mm/rev)
Revolution
(min-1)
5400
4700
3800
3500
2900
2500
2200
1600
1300
0.09
0.11
0.14
0.18
0.21
0.23
0.26
0.29
0.3
(0.06 0.12)
(0.07 0.14)
(0.09 0.18)
(0.11 0.24)
(0.16 0.25)
(0.19 0.27)
(0.23 0.29)
(0.24 0.33)
(0.26 0.34)
No 45 B etc
60-40-8 etc
Drill Dia.
DC
(mm)
Revolution
(min-1)
3.0
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
1900
1500
1200
1200
900
700
600
400
300
Feed rate
(Min.Max.)
(mm/rev)
0.07
0.08
0.1
0.13
0.14
0.16
0.18
0.19
0.2
(0.05 0.08)
(0.06 0.10)
(0.07 0.13)
(0.09 0.17)
(0.10 0.18)
(0.12 0.19)
(0.15 0.20)
(0.15 0.23)
(0.15 0.24)

Work
Material
Drill Dia.
DC
(mm)
Revolution
(min-1)
3.0
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
7900
6300
5000
4500
3500
2800
2600
1900
1700
Feed rate
(Min.Max.)
(mm/rev)
0.1
0.12
0.15
0.2
0.23
0.27
0.31
0.33
0.35
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
Feed rate
(Min.Max.)
(mm/rev)
Revolution
(min-1)
6900
5500
4400
3700
2900
2300
2100
1500
1300
0.1
0.12
0.15
0.2
0.25
0.29
0.33
0.35
0.37
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.31)
(0.22 0.35)
(0.28 0.37)
(0.28 0.42)
(0.30 0.44)
Feed rate
(Min.Max.)
(mm/rev)
Revolution
(min-1)
6400
5100
4100
3500
2700
2200
1900
1400
1200
0.1
0.12
0.15
0.2
0.23
0.27
0.31
0.33
0.35
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
Inconel718 etc
AISI H13, L6 etc

Feed rate
(Min.Max.)
(mm/rev)
Revolution
(min-1)
1900
1500
1200
1200
900
700
600
400
400
0.07
0.09
0.11
0.14
0.14
0.16
0.16
0.18
0.19
(0.05 0.09)
(0.06 0.11)
(0.08 0.14)
(0.09 0.19)
(0.11 0.17)
(0.12 0.19)
(0.13 0.18)
(0.14 0.21)
(0.15 0.22)
Feed rate
(Min.Max.)
(mm/rev)
Revolution
(min-1)
1900
1500
1200
1200
900
700
600
400
400
0.07
0.09
0.11
0.14
0.14
0.16
0.16
0.18
0.19
(0.05 0.09)
(0.06 0.11)
(0.08 0.14)
(0.09 0.19)
(0.11 0.17)
(0.12 0.19)
(0.13 0.18)
(0.14 0.21)
(0.15 0.22)
DRILLING
Work
Material
N061
CARBIDE
MWE
WSTAR DRILLS
Drill Length
Drill Installation
A > DC x 1.5
Run-out < 0.03mm
Drill Installation
Thin Workpiece
Interrupted Cutting
Adjusting Screw
Drill Holding
DC

Coolant Method
One Process
1DC
If Bending
Occurs

end and at the center are
ideal.
DRILLING
Stepped Holes
N062

zWhen machining a prepared hole

with the MZE-SB please set the
depth to 1DC (DC=drill diameter).

cutting.
xAdd a 45chamfer.
zLower the feed

when drilling
the interrupted
part.
Requires Prior
Machining
Support
the Workpiece
zSpot face with

an end mill
prior to drilling.
MQS
WSTAR DRILLS
Steel
DC=3
0
0.012
0
0.006
Cast Iron
h6
3<DC < 6 6<DC < 10 10<DC < 1818<DC < 20

0
0.012
0
0.008
0
0.018
0
0.011
LF
135
DC(h7)
PL
0
0.015
0
0.009
LCF
LH
0
0.021
0
0.013
DCON(h6)
CARBIDE
Type1
DCON(h6)
aNew grade DP3020, unique coolant system, triple margin.

aHigh efficiency and high accuracy machining of steel and cast iron is possible.
Type2
OAL
LF
135
DC(h7)
PL
LCF
LH
OAL
(Note) MQS drills are suitable for use with shrink fit holders.
3
5
3
3.8
5
3
3.9
5
3.7
4.0 5
3
4.1
5
a
a
3
5
3
4.3
5
3
4.4
5
4.2
4.5 5
1
1
21.7 23.7 70.7 70 0.7

28.7 31.7 78.7 78 0.7
4
4
1
1
21.7 23.7 70.7 70 0.7

28.7 31.7 78.7 78 0.7
4
4
1
1
21.7 23.7 70.7 70 0.7

28.7 31.7 78.7 78 0.7
41.7 41.7 87.7 87 0.7
4
4
4
1
1
1
22.7 23.7 70.7 70 0.7

30.7 31.7 78.7 78 0.7
4
4
1
1
22.8 23.8 70.8 70 0.8

30.8 31.8 78.8 78 0.8
4
4
1
1
22.8 23.8 70.8 70 0.8

30.8 31.8 78.8 78 0.8
4
4
1
1
22.8 23.8 70.8 70 0.8

30.8 31.8 78.8 78 0.8
4
4
1
1
22.8 23.8 70.8 70 0.8

30.8 31.8 78.8 78 0.8
46.8 46.8 92.8 92 0.8
4
4
4
1
1
1
24.8 26.8 73.8 73 0.8

33.8 35.8 82.8 82 0.8
5
5
1
1
24.9 26.9 73.9 73 0.9

33.9 35.9 82.9 82 0.9
5
5
1
1
24.9 26.9 73.9 73 0.9

33.9 35.9 82.9 82 0.9
5
5
1
1
24.9 26.9 73.9 73 0.9

33.9 35.9 82.9 82 0.9
5
5
1
1
24.9 26.9 73.9 73 0.9

33.9 35.9 82.9 82 0.9
52.9 52.9 100.9 100 0.9
5
5
5
1
1
1
4.8
3
5
4.9
3
5
5.0 5
5.1
3
5
5.2
3
5
5.3
3
5
5.4
3
5
5.5 5
5.6
3
5
5.7
3
5
5.8
3
5
5.9
3
5
6.0 5
3
5
6.1
26.0 29.0 76.0 75 1.0

36.0 39.0 86.0 85 1.0
5
5
1
1
26.0 29.0 76.0 75 1.0

36.0 39.0 86.0 85 1.0
5
5
1
1
26.0 29.0 76.0 75 1.0

36.0 39.0 86.0 85 1.0
5
5
1
1
26.0 29.0 76.0 75 1.0

36.0 39.0 86.0 85 1.0
5
5
1
1
26.0 29.0 76.0 75 1.0

36.0 39.0 86.0 85 1.0
58.0 58.0 106.0 105 1.0
5
5
5
1
1
1
29.1 31.1 82.1 81 1.1

40.1 43.1 90.1 89 1.1
6
6
1
1
29.1 31.1 82.1 81 1.1

40.1 43.1 90.1 89 1.1
6
6
1
1
29.1 31.1 82.1 81 1.1

40.1 43.1 90.1 89 1.1
6
6
1
1
29.1 31.1 82.1 81 1.1

40.1 43.1 90.1 89 1.1
6
6
1
1
29.1 31.1 82.1 81 1.1

40.1 43.1 90.1 89 1.1
62.1 67.1 119.1 118 1.1
6
6
6
1
1
1
31.2 31.2 82.2 81 1.2

43.2 43.2 90.2 89 1.2
6
6
1
1
31.2 31.2 82.2 81 1.2

43.2 43.2 90.2 89 1.2
6
6
1
1
31.2 31.2 82.2 81 1.2

43.2 43.2 90.2 89 1.2
6
6
1
1
31.2 31.2 82.2 81 1.2

43.2 43.2 90.2 89 1.2
6
6
1
1
31.2 31.2 82.2 81 1.2

43.2 43.2 90.2 89 1.2
67.2 67.2 119.2 118 1.2
6
6
6
1
1
1
34.3 36.3 87.3 86 1.3

47.3 49.3 96.3 95 1.3
7
7
1
1
DRILLING
3
3.6
5
4
4
3
5
DCON
21.7 23.7 70.7 70 0.7

28.7 31.7 78.7 78 0.7
4.7
MQS0460X3DB
MQS0460X5DB
MQS0470X3DB
MQS0470X5DB
MQS0480X3DB
MQS0480X5DB
MQS0490X3DB
MQS0490X5DB
MQS0500X3DB
MQS0500X5DB
MQS0500X8DB
MQS0510X3DB
MQS0510X5DB
MQS0520X3DB
MQS0520X5DB
MQS0530X3DB
MQS0530X5DB
MQS0540X3DB
MQS0540X5DB
MQS0550X3DB
MQS0550X5DB
MQS0550X8DB
MQS0560X3DB
MQS0560X5DB
MQS0570X3DB
MQS0570X5DB
MQS0580X3DB
MQS0580X5DB
MQS0590X3DB
MQS0590X5DB
MQS0600X3DB
MQS0600X5DB
MQS0600X8DB
MQS0610X3DB
MQS0610X5DB
PL
3
3.5 5
8
1
1
LF
4
4
3
5
OAL
3
3.4
5
21.6 23.6 70.6 70 0.6

28.6 31.6 78.6 78 0.6
4.6
(mm) (l/d)
Type
LH
1
1
Order Number
LCF
3
3.3
5
3.2
3
3
DC
Dimensions (mm)
Stock
DP3020
3
5
DCON
28.6 31.6 78.6 78 0.6

35.6 35.6 81.6 81 0.6
PL
3
3.1
5
LF
OAL
21.6 23.6 70.6 70 0.6
LH
3.0 5
MQS0300X3DB
MQS0300X5DB
MQS0300X8DB
MQS0310X3DB
MQS0310X5DB
MQS0320X3DB
MQS0320X5DB
MQS0330X3DB
MQS0330X5DB
MQS0340X3DB
MQS0340X5DB
MQS0350X3DB
MQS0350X5DB
MQS0350X8DB
MQS0360X3DB
MQS0360X5DB
MQS0370X3DB
MQS0370X5DB
MQS0380X3DB
MQS0380X5DB
MQS0390X3DB
MQS0390X5DB
MQS0400X3DB
MQS0400X5DB
MQS0400X8DB
MQS0410X3DB
MQS0410X5DB
MQS0420X3DB
MQS0420X5DB
MQS0430X3DB
MQS0430X5DB
MQS0440X3DB
MQS0440X5DB
MQS0450X3DB
MQS0450X5DB
MQS0450X8DB
LCF
Type
Hole Depth
Dimensions (mm)
Order Number
(mm) (l/d)
Internal Coolant
Stock
DP3020
DC
Hole Depth
Internal Coolant
CUTTING CONDITIONS
a
OPERATION GUIDANCE
TECHNICAL DATA
N067
N069
Q001
N063
MQS
WSTAR DRILLS
3
5
6.8
3
5
3
6.9
5
DRILLING
7.0 5
7.1
3
5
7.2
3
5
7.3
3
5
3
7.4
5
7.5 5
7.6
3
5
7.7
3
5
7.8
3
5
3
7.9
5
8.0 5
3
5
3
8.4
5
8.1
8.2
8.3
1
1
34.3 36.3 87.3 86 1.3

47.3 49.3 96.3 95 1.3
73.3 78.3 131.3 130 1.3
7
7
7
1
1
1
36.4 38.4 91.4 90 1.4

50.4 52.4 99.4 98 1.4
7
7
1
1
36.4 38.4 91.4 90 1.4

50.4 52.4 99.4 98 1.4
7
7
1
1
36.4 38.4 91.4 90 1.4

50.4 52.4 99.4 98 1.4
7
7
1
1
36.4 38.4 91.4 90 1.4

50.4 52.4 99.4 98 1.4
7
7
1
1
36.4 38.4 91.4 90 1.4

50.4 52.4 99.4 98 1.4
78.4 78.4 131.4 130 1.4
7
7
7
1
1
1
39.5 40.5 91.5 90 1.5

54.5 57.5 104.5 103 1.5
8
8
1
1
39.5 40.5 91.5 90 1.5

54.5 57.5 104.5 103 1.5
8
8
1
1
39.5 40.5 91.5 90 1.5

54.5 57.5 104.5 103 1.5
8
8
1
1
39.5 40.5 91.5 90 1.5

54.5 57.5 104.5 103 1.5
8
8
1
1
39.6 40.6 91.6 90 1.6

54.6 57.6 104.6 103 1.6
84.6 89.6 143.6 142 1.6
8
8
8
1
1
2
41.6 41.6 91.6 90 1.6

57.6 57.6 104.6 103 1.6
8
8
1
1
41.6 41.6 91.6 90 1.6

57.6 57.6 104.6 103 1.6
8
8
1
1
41.6 41.6 91.6 90 1.6

57.6 57.6 104.6 103 1.6
8
8
1
1
41.6 41.6 91.6 90 1.6

57.6 57.6 104.6 103 1.6
8
8
1
1
41.7 41.7 91.7 90 1.7

57.7 57.7 104.7 103 1.7
89.7 89.7 143.7 142 1.7
8
8
8
1
1
2
44.7 46.7 97.7 96 1.7

61.7 63.7 114.7 113 1.7
9
9
1
1
44.7 46.7 97.7 96 1.7
61.7 63.7 114.7 113 1.7
8.6
3
5
8.7
3
5
8.8
3
5
8.9
3
5
MQS0850X3DB
MQS0850X5DB
MQS0850X8DB
MQS0860X3DB
MQS0860X5DB
MQS0870X3DB
MQS0870X5DB
MQS0880X3DB
MQS0880X5DB
MQS0890X3DB
MQS0890X5DB
MQS0900X3DB
MQS0900X5DB
MQS0900X8DB
MQS0910X3DB
MQS0910X5DB
MQS0920X3DB
MQS0920X5DB
MQS0930X3DB
MQS0930X5DB
MQS0940X3DB
MQS0940X5DB
MQS0950X3DB
MQS0950X5DB
MQS0950X8DB
MQS0960X3DB
MQS0960X5DB
MQS0970X3DB
MQS0970X5DB
MQS0980X3DB
MQS0980X5DB
MQS0990X3DB
MQS0990X5DB
MQS1000X3DB
MQS1000X5DB
MQS1000X8DB
MQS1010X3DB
MQS1010X5DB
MQS1020X3DB
MQS1020X5DB
MQS1030X3DB
MQS1030X5DB
MQS1040X3DB
MQS1040X5DB
MQS1050X3DB
MQS1050X5DB
MQS1050X8DB
MQS1060X3DB
MQS1060X5DB
44.7 46.7 97.7 96 1.7
61.7 63.7 114.7 113 1.7
44.7 46.7 97.7 96 1.7

61.7 63.7 114.7 113 1.7
9
9
1
1
9.0 5
9.1
3
5
9.2
3
5
9.3
3
5
9.4
3
5
3
9.5 5
8
9.6
3
5
9.7
3
5
9.8
3
5
9.9
3
5
3
10.0 5
8
3
10.1
5
10.2
3
5
10.3
3
5
10.4
3
5
3
10.5 5
8
3
10.6
5
a
a
a
a
a
a
N064
DCON
6.7
7
7
PL
34.3 36.3 87.3 86 1.3

47.3 49.3 96.3 95 1.3
LF
3
5
1
1
8.5 5
(mm) (l/d)
OAL
6.6
7
7
Order Number
LH
34.3 36.3 87.3 86 1.3

47.3 49.3 96.3 95 1.3
Dimensions (mm)
Stock
DP3020
3
6.5 5
8
1
1
DC
Hole Depth
DCON
3
6.4
5
7
7
PL
6.3
34.3 36.3 87.3 86 1.3

47.3 49.3 96.3 95 1.3
LF
3
5
MQS0620X3DB
MQS0620X5DB
MQS0630X3DB
MQS0630X5DB
MQS0640X3DB
MQS0640X5DB
MQS0650X3DB
MQS0650X5DB
MQS0650X8DB
MQS0660X3DB
MQS0660X5DB
MQS0670X3DB
MQS0670X5DB
MQS0680X3DB
MQS0680X5DB
MQS0690X3DB
MQS0690X5DB
MQS0700X3DB
MQS0700X5DB
MQS0700X8DB
MQS0710X3DB
MQS0710X5DB
MQS0720X3DB
MQS0720X5DB
MQS0730X3DB
MQS0730X5DB
MQS0740X3DB
MQS0740X5DB
MQS0750X3DB
MQS0750X5DB
MQS0750X8DB
MQS0760X3DB
MQS0760X5DB
MQS0770X3DB
MQS0770X5DB
MQS0780X3DB
MQS0780X5DB
MQS0790X3DB
MQS0790X5DB
MQS0800X3DB
MQS0800X5DB
MQS0800X8DB
MQS0810X3DB
MQS0810X5DB
MQS0820X3DB
MQS0820X5DB
MQS0830X3DB
MQS0830X5DB
MQS0840X3DB
MQS0840X5DB
OAL
LH
3
6.2
5
Type
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
DP3020
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
Type
44.8 46.8 97.8 96 1.8

61.8 63.8 114.8 113 1.8
95.8 100.8 155.8 154 1.8
9 1
9 1
9 2
46.8 48.8 102.8 101 1.8

64.8 66.8 117.8 116 1.8
9 1
9 1
46.8 48.8 102.8 101 1.8

64.8 66.8 117.8 116 1.8
9 1
9 1
46.8 48.8 102.8 101 1.8

64.8 66.8 117.8 116 1.8
9 1
9 1
46.8 48.8 102.8 101 1.8

64.8 66.8 117.8 116 1.8
9 1
9 1
46.9 48.9 102.9 101 1.9

64.9 66.9 117.9 116 1.9
100.9 100.9 155.9 154 1.9
9 1
9 1
9 2
49.9 51.9 102.9 101 1.9 10 1

68.9 71.9 122.9 121 1.9 10 1
49.9 51.9 102.9 101 1.9 10 1
68.9 71.9 122.9 121 1.9 10 1
49.9 51.9 102.9 101 1.9 10 1
68.9 71.9 122.9 121 1.9 10 1
49.9 51.9 102.9 101 1.9 10 1
68.9 71.9 122.9 121 1.9 10 1
50.0 52.0 103.0 101 2.0 10 1
69.0 72.0 123.0 121 2.0 10 1
107.0 112.0 168.0 166 2.0 10 2
52.0 52.0 103.0 101 2.0 10 1
72.0 72.0 123.0 121 2.0 10 1
52.0 52.0 103.0 101 2.0 10 1
72.0 72.0 123.0 121 2.0 10 1
52.0 52.0 103.0 101 2.0 10 1
72.0 72.0 123.0 121 2.0 10 1
52.1 52.1 103.1 101 2.1 10 1
72.1 72.1 123.1 121 2.1 10 1
52.1 52.1 103.1 101 2.1 10 1
72.1 72.1 123.1 121 2.1 10 1
112.1 112.1 168.1 166 2.1 10 2
55.1 57.1 113.1 111 2.1
76.1 80.1 136.1 134 2.1
11 1
11 1
55.1 57.1 113.1 111 2.1

76.1 80.1 136.1 134 2.1
11 1
11 1
55.1 57.1 113.1 111 2.1

76.1 80.1 136.1 134 2.1
11 1
11 1
55.2 57.2 113.2 111 2.2

76.2 80.2 136.2 134 2.2
11 1
11 1
55.2 57.2 113.2 111 2.2

76.2 80.2 136.2 134 2.2
118.2 123.2 184.2 182 2.2
11 1
11 1
11 2
57.2 58.2 118.2 116 2.2

79.2 80.2 136.2 134 2.2
11 1
11 1
CARBIDE
11.3
3
5
3
11.4
5
11.5 5
11.6
3
5
11.7
3
5
11.8
3
5
3
11.9
5
12.0 5
12.1
3
5
12.2
3
5
12.3
3
5
3
12.4
5
12.5 5
12.6
3
5
12.7
3
5
12.8
3
5
3
12.9
5
11 1
11 1
11 2
60.3 62.3 118.3 116 2.3 12 1

83.3 86.3 142.3 140 2.3 12 1
60.3 62.3 118.3 116 2.3 12 1
83.3 86.3 142.3 140 2.3 12 1
60.3 62.3 118.3 116 2.3 12 1
83.3 86.3 142.3 140 2.3 12 1
60.4 62.4 118.4 116 2.4 12 1
83.4 86.4 142.4 140 2.4 12 1
60.4 62.4 118.4 116 2.4 12 1
83.4 86.4 142.4 140 2.4 12 1
129.4 134.4 196.4 194 2.4 12 2
62.4 62.4 118.4 116 2.4 12 1
86.4 86.4 142.4 140 2.4 12 1
62.4 62.4 118.4 116 2.4 12 1
86.4 86.4 142.4 140 2.4 12 1
62.4 62.4 118.4 116 2.4 12 1
86.4 86.4 142.4 140 2.4 12 1
62.5 62.5 118.5 116 2.5 12 1
86.5 86.5 142.5 140 2.5 12 1
62.5 62.5 118.5 116 2.5 12 1
86.5 86.5 142.5 140 2.5 12 1
134.5 134.5 196.5 194 2.5 12 2
65.5 68.5 124.5 122 2.5 13 1
90.5 94.5 150.5 148 2.5 13 1
65.5 68.5 124.5 122 2.5 13 1
90.5 94.5 150.5 148 2.5 13 1
65.5 68.5 124.5 122 2.5 13 1
90.5 94.5 150.5 148 2.5 13 1
65.6 68.6 124.6 122 2.6 13 1
90.6 94.6 150.6 148 2.6 13 1
65.6 68.6 124.6 122 2.6 13 1
90.6 94.6 150.6 148 2.6 13 1
140.6 145.6 208.6 206 2.6 13 2
67.6 68.6 124.6 122 2.6 13 1
93.6 94.6 150.6 148 2.6 13 1
67.6 68.6 124.6 122 2.6 13 1
93.6 94.6 150.6 148 2.6 13 1
67.7 68.7 124.7 122 2.7 13 1
93.7 94.7 150.7 148 2.7 13 1
67.7 68.7 124.7 122 2.7 13 1
93.7 94.7 150.7 148 2.7 13 1
13.1
3
5
13.2
3
5
13.3
3
5
13.4
3
5
13.5 5
13.6
3
5
13.7
3
5
13.8
3
5
13.9
3
5
3
14.0 5
8
14.1
3
5
14.2
3
5
14.3
3
5
14.4
3
5
3
14.5 5
8
3
14.6
5
14.7
3
5
14.8
3
5
14.9
3
5
3
15.0 5
8
3
15.1
5
a
a
a
a
a
a
Type
67.7 68.7 124.7 122 2.7 13 1

93.7 94.7 150.7 148 2.7 13 1
145.7 145.7 208.7 206 2.7 13 2
70.7 72.7 128.7 126 2.7 14 1
97.7 100.7 156.7 154 2.7 14 1
70.7 72.7 128.7 126 2.7 14 1
97.7 100.7 156.7 154 2.7 14 1
70.8 72.8 128.8 126 2.8 14 1
97.8 100.8 156.8 154 2.8 14 1
70.8 72.8 128.8 126 2.8 14 1
97.8 100.8 156.8 154 2.8 14 1
70.8 72.8 128.8 126 2.8 14 1
97.8 100.8 156.8 154 2.8 14 1
151.8 156.8 220.8 218 2.8 14 2
72.8 72.8 128.8 126 2.8 14 1
100.8 100.8 156.8 154 2.8 14 1
72.8 72.8 128.8 126 2.8 14 1
100.8 100.8 156.8 154 2.8 14 1
72.9 72.9 128.9 126 2.9 14 1
100.9 100.9 156.9 154 2.9 14 1
72.9 72.9 128.9 126 2.9 14 1
100.9 100.9 156.9 154 2.9 14 1
72.9 72.9 128.9 126 2.9 14 1
100.9 100.9 156.9 154 2.9 14 1
156.9 156.9 220.9 218 2.9 14 2
75.9 78.9 137.9 135 2.9 15 1
104.9 108.9 167.9 165 2.9 15 1
75.9 78.9 137.9 135 2.9 15 1
104.9 108.9 167.9 165 2.9 15 1
76.0 79.0 138.0 135 3.0 15 1
105.0 109.0 168.0 165 3.0 15 1
76.0 79.0 138.0 135 3.0 15 1
105.0 109.0 168.0 165 3.0 15 1
76.0 79.0 138.0 135 3.0 15 1
105.0 109.0 168.0 165 3.0 15 1
163.0 168.0 228.0 225 3.0 15 2
78.0 79.0 138.0 135 3.0 15 1
108.0 109.0 168.0 165 3.0 15 1
78.0 79.0 138.0 135 3.0 15 1
108.0 109.0 168.0 165 3.0 15 1
78.1 79.1 138.1 135 3.1 15 1
108.1 109.1 168.1 165 3.1 15 1
DRILLING
57.3 58.3 118.3 116 2.3

79.3 80.3 136.3 134 2.3
123.3 123.3 184.3 182 2.3
DCON
3
5
11 1
11 1
MQS1300X3DB
MQS1300X5DB
MQS1300X8DB
MQS1310X3DB
MQS1310X5DB
MQS1320X3DB
MQS1320X5DB
MQS1330X3DB
MQS1330X5DB
MQS1340X3DB
MQS1340X5DB
MQS1350X3DB
MQS1350X5DB
MQS1350X8DB
MQS1360X3DB
MQS1360X5DB
MQS1370X3DB
MQS1370X5DB
MQS1380X3DB
MQS1380X5DB
MQS1390X3DB
MQS1390X5DB
MQS1400X3DB
MQS1400X5DB
MQS1400X8DB
MQS1410X3DB
MQS1410X5DB
MQS1420X3DB
MQS1420X5DB
MQS1430X3DB
MQS1430X5DB
MQS1440X3DB
MQS1440X5DB
MQS1450X3DB
MQS1450X5DB
MQS1450X8DB
MQS1460X3DB
MQS1460X5DB
MQS1470X3DB
MQS1470X5DB
MQS1480X3DB
MQS1480X5DB
MQS1490X3DB
MQS1490X5DB
MQS1500X3DB
MQS1500X5DB
MQS1500X8DB
MQS1510X3DB
MQS1510X5DB
PL
11.2
57.3 58.3 118.3 116 2.3

79.3 80.3 136.3 134 2.3
LF
11 1
11 1
OAL
3
5
57.2 58.2 118.2 116 2.2

79.2 80.2 136.2 134 2.2
13.0 5
(mm) (l/d)
LH
11.1
11 1
11 1
Order Number
LCF
57.2 58.2 118.2 116 2.2

79.2 80.2 136.2 134 2.2
DC
Dimensions (mm)
Stock
DP3020
3
11.0 5
8
Type
Hole Depth
DCON
3
10.9
5
PL
10.8
LF
3
5
MQS1070X3DB
MQS1070X5DB
MQS1080X3DB
MQS1080X5DB
MQS1090X3DB
MQS1090X5DB
MQS1100X3DB
MQS1100X5DB
MQS1100X8DB
MQS1110X3DB
MQS1110X5DB
MQS1120X3DB
MQS1120X5DB
MQS1130X3DB
MQS1130X5DB
MQS1140X3DB
MQS1140X5DB
MQS1150X3DB
MQS1150X5DB
MQS1150X8DB
MQS1160X3DB
MQS1160X5DB
MQS1170X3DB
MQS1170X5DB
MQS1180X3DB
MQS1180X5DB
MQS1190X3DB
MQS1190X5DB
MQS1200X3DB
MQS1200X5DB
MQS1200X8DB
MQS1210X3DB
MQS1210X5DB
MQS1220X3DB
MQS1220X5DB
MQS1230X3DB
MQS1230X5DB
MQS1240X3DB
MQS1240X5DB
MQS1250X3DB
MQS1250X5DB
MQS1250X8DB
MQS1260X3DB
MQS1260X5DB
MQS1270X3DB
MQS1270X5DB
MQS1280X3DB
MQS1280X5DB
MQS1290X3DB
MQS1290X5DB
OAL
LH
3
10.7
5
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
DP3020
DC
Hole Depth
Internal Coolant
Stock
78.1 79.1 138.1 135 3.1 15 1

108.1 109.1 168.1 165 3.1 15 1
78.1 79.1 138.1 135 3.1 15 1
108.1 109.1 168.1 165 3.1 15 1
168.1 168.1 228.1 225 3.1 15 2
81.1 83.1 142.1 139 3.1 16 1
112.1 115.1 174.1 171 3.1 16 1
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N067
N069
Q001
N065
MQS
WSTAR DRILLS
3
15.7
5
a
a
3
5
3
15.9
5
15.8
DRILLING
16.0 5
16.1
3
5
16.2
3
5
16.3
3
5
16.4
3
5
16.5
3
5
16.6
3
5
16.7
3
5
16.8
3
5
16.9
3
5
17.0
3
5
17.1
3
5
17.2
3
5
17.3
3
5
17.4
3
5
17.5
3
5
3
5
81.2 83.2 142.2 139 3.2 16 1

112.2 115.2 174.2 171 3.2 16 1
17.8
3
5
17.9
3
5
18.0
3
5
18.1
3
5
18.2
3
5
18.3
3
5
18.4
3
5
18.5
3
5
86.3 89.3 148.3 145 3.3 17 1

119.3 123.3 182.3 179 3.3 17 1
18.6
3
5
86.4 89.4 148.4 145 3.4 17 1

119.4 123.4 182.4 179 3.4 17 1
18.7
3
5
86.4 89.4 148.4 145 3.4 17 1

119.4 123.4 182.4 179 3.4 17 1
18.8
3
5
86.4 89.4 148.4 145 3.4 17 1

119.4 123.4 182.4 179 3.4 17 1
18.9
3
5
86.4 89.4 148.4 145 3.4 17 1

119.4 123.4 182.4 179 3.4 17 1
19.0
3
5
88.4 89.4 148.4 145 3.4 17 1

122.4 123.4 182.4 179 3.4 17 1
19.1
3
5
88.5 89.5 148.5 145 3.5 17 1

122.5 123.5 182.5 179 3.5 17 1
19.2
3
5
88.5 89.5 148.5 145 3.5 17 1

122.5 123.5 182.5 179 3.5 17 1
19.3
3
5
88.5 89.5 148.5 145 3.5 17 1

122.5 123.5 182.5 179 3.5 17 1
19.4
3
5
88.5 89.5 148.5 145 3.5 17 1

122.5 123.5 182.5 179 3.5 17 1
19.5
3
5
91.5 93.5 152.5 149 3.5 18 1

126.5 129.5 188.5 185 3.5 18 1
19.6
3
5
91.6 93.6 152.6 149 3.6 18 1

126.6 129.6 188.6 185 3.6 18 1
19.7
3
5
91.6 93.6 152.6 149 3.6 18 1

126.6 129.6 188.6 185 3.6 18 1
19.8
3
5
91.6 93.6 152.6 149 3.6 18 1

126.6 129.6 188.6 185 3.6 18 1
19.9
3
5
91.6 93.6 152.6 149 3.6 18 1

126.6 129.6 188.6 185 3.6 18 1
20.0
3
5
81.2 83.2 142.2 139 3.2 16 1

112.2 115.2 174.2 171 3.2 16 1
174.2 184.2 244.2 241 3.2 16 2
83.2 83.2 142.2 139 3.2 16 1
115.2 115.2 174.2 171 3.2 16 1
83.3 83.3 142.3 139 3.3 16 1
115.3 115.3 174.3 171 3.3 16 1
83.3 83.3 142.3 139 3.3 16 1
115.3 115.3 174.3 171 3.3 16 1
83.3 83.3 142.3 139 3.3 16 1
115.3 115.3 174.3 171 3.3 16 1
83.3 83.3 142.3 139 3.3 16 1
115.3 115.3 174.3 171 3.3 16 1
179.3 184.3 244.3 241 3.3 16 2
N066
DCON
17.7
PL
3
15.6
5
81.2 83.2 142.2 139 3.2 16 1

112.2 115.2 174.2 171 3.2 16 1
MQS1760X3DB
MQS1760X5DB
MQS1770X3DB
MQS1770X5DB
MQS1780X3DB
MQS1780X5DB
MQS1790X3DB
MQS1790X5DB
MQS1800X3DB
MQS1800X5DB
MQS1810X3DB
MQS1810X5DB
MQS1820X3DB
MQS1820X5DB
MQS1830X3DB
MQS1830X5DB
MQS1840X3DB
MQS1840X5DB
MQS1850X3DB
MQS1850X5DB
MQS1860X3DB
MQS1860X5DB
MQS1870X3DB
MQS1870X5DB
MQS1880X3DB
MQS1880X5DB
MQS1890X3DB
MQS1890X5DB
MQS1900X3DB
MQS1900X5DB
MQS1910X3DB
MQS1910X5DB
MQS1920X3DB
MQS1920X5DB
MQS1930X3DB
MQS1930X5DB
MQS1940X3DB
MQS1940X5DB
MQS1950X3DB
MQS1950X5DB
MQS1960X3DB
MQS1960X5DB
MQS1970X3DB
MQS1970X5DB
MQS1980X3DB
MQS1980X5DB
MQS1990X3DB
MQS1990X5DB
MQS2000X3DB
MQS2000X5DB
LF
(mm) (l/d)
OAL
3
15.5 5
8
3
5
Type
LH
DP3020
3
5
Hole Depth
15.4
DCON
17.6
PL
3
5
81.1 83.1 142.1 139 3.1 16 1

112.1 115.1 174.1 171 3.1 16 1
LF
15.3
MQS1520X3DB
MQS1520X5DB
MQS1530X3DB
MQS1530X5DB
MQS1540X3DB
MQS1540X5DB
MQS1550X3DB
MQS1550X5DB
MQS1550X8DB
MQS1560X3DB
MQS1560X5DB
MQS1570X3DB
MQS1570X5DB
MQS1580X3DB
MQS1580X5DB
MQS1590X3DB
MQS1590X5DB
MQS1600X3DB
MQS1600X5DB
MQS1600X8DB
MQS1610X3DB
MQS1610X5DB
MQS1620X3DB
MQS1620X5DB
MQS1630X3DB
MQS1630X5DB
MQS1640X3DB
MQS1640X5DB
MQS1650X3DB
MQS1650X5DB
MQS1660X3DB
MQS1660X5DB
MQS1670X3DB
MQS1670X5DB
MQS1680X3DB
MQS1680X5DB
MQS1690X3DB
MQS1690X5DB
MQS1700X3DB
MQS1700X5DB
MQS1710X3DB
MQS1710X5DB
MQS1720X3DB
MQS1720X5DB
MQS1730X3DB
MQS1730X5DB
MQS1740X3DB
MQS1740X5DB
MQS1750X3DB
MQS1750X5DB
OAL
LH
3
15.2
5
DC
Dimensions (mm)
Stock
Order Number
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
DP3020
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
Type
93.6 93.6 152.6 149 3.6 18 1

129.6 129.6 188.6 185 3.6 18 1
93.7 93.7 152.7 149 3.7 18 1
129.7 129.7 188.7 185 3.7 18 1
93.7 93.7 152.7 149 3.7 18 1
129.7 129.7 188.7 185 3.7 18 1
93.7 93.7 152.7 149 3.7 18 1
129.7 129.7 188.7 185 3.7 18 1
93.7 93.7 152.7 149 3.7 18 1
129.7 129.7 188.7 185 3.7 18 1
96.7 99.7 160.7 157 3.7 19 1
133.7 137.7 198.7 195 3.7 19 1
96.8 99.8 160.8 157 3.8 19 1
133.8 137.8 198.8 195 3.8 19 1
96.8 99.8 160.8 157 3.8 19 1
133.8 137.8 198.8 195 3.8 19 1
96.8 99.8 160.8 157 3.8 19 1
133.8 137.8 198.8 195 3.8 19 1
96.8 99.8 160.8 157 3.8 19 1
133.8 137.8 198.8 195 3.8 19 1
98.9 99.9 160.9 157 3.9 19 1
136.9 137.9 198.9 195 3.9 19 1
98.9 99.9 160.9 157 3.9 19 1
136.9 137.9 198.9 195 3.9 19 1
98.9 99.9 160.9 157 3.9 19 1
136.9 137.9 198.9 195 3.9 19 1
98.9 99.9 160.9 157 3.9 19 1
136.9 137.9 198.9 195 3.9 19 1
98.9 99.9 160.9 157 3.9 19 1
136.9 137.9 198.9 195 3.9 19 1
102.0 104.0 165.0 161 4.0 20 1
141.0 144.0 205.0 201 4.0 20 1
102.0 104.0 165.0 161 4.0 20 1
141.0 144.0 205.0 201 4.0 20 1
102.0 104.0 165.0 161 4.0 20 1
141.0 144.0 205.0 201 4.0 20 1
102.0 104.0 165.0 161 4.0 20 1
141.0 144.0 205.0 201 4.0 20 1
102.0 104.0 165.0 161 4.0 20 1
141.0 144.0 205.0 201 4.0 20 1
104.1 104.1 165.1 161 4.1 20 1
144.1 144.1 205.1 201 4.1 20 1
104.1 104.1 165.1 161 4.1 20 1
144.1 144.1 205.1 201 4.1 20 1
104.1 104.1 165.1 161 4.1 20 1
144.1 144.1 205.1 201 4.1 20 1
104.1 104.1 165.1 161 4.1 20 1
144.1 144.1 205.1 201 4.1 20 1
104.1 104.1 165.1 161 4.1 20 1
144.1 144.1 205.1 201 4.1 20 1
CARBIDE

y Internal Coolant
AISI 1010 etc
Drill Dia.
Cutting Speed Revolution
DC
(m/min)
(min-1)
(mm)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
Work
Material
130
130
130
140
140
140
160
180
180
12900
10300
8200
7000
5500
4400
4200
3500
2800
Feed rate
(Min. Max.)
(mm/rev)
0.15
0.2
0.2
0.25
0.25
0.27
0.3
0.33
0.35
Work
Material
100
100
100
130
130
130
140
150
150
9900
7900
6300
6500
5100
4100
3700
2900
2300
AISI 4340 etc
No 45 B etc
70
80
80
90
100
110
120
130
130
6900
6300
5000
4500
3900
3500
3100
2500
2000
Feed rate
(Min. Max.)
(mm/rev)
0.1
0.11
0.14
0.18
0.21
0.23
0.26
0.28
0.3
(0.06 0.15)
(0.07 0.15)
(0.09 0.18)
(0.11 0.24)
(0.16 0.25)
(0.19 0.27)
(0.22 0.30)
(0.23 0.33)
(0.26 0.35)
690
690
700
810
815
805
805
700
600
110
110
110
120
120
130
150
160
160
10900
8700
7000
6000
4700
4100
3900
3100
2500
60-40-8 etc
100-70-03 etc
90
90
90
100
100
100
110
120
120
8900
7100
5700
5000
3900
3100
2900
2300
1900
Feed rate
(Min. Max.)
(mm/rev)
0.25
0.25
0.25
0.3
0.3
0.3
0.35
0.35
0.35
(0.15 0.32)
(0.15 0.32)
(0.15 0.32)
(0.20 0.38)
(0.20 0.38)
(0.22 0.38)
(0.26 0.40)
(0.28 0.40)
(0.30 0.40)
0.15
0.2
0.2
0.25
0.25
0.27
0.3
0.33
0.35
0.28
0.28
0.3
0.33
0.35
0.4
0.45
0.5
0.5
75
75
75
85
85
85
95
110
110
7400
5900
4700
4200
3300
2700
2500
2100
1700
(0.15 0.35)
(0.15 0.35)
(0.15 0.40)
(0.20 0.45)
(0.20 0.45)
(0.22 0.45)
(0.26 0.50)
(0.28 0.60)
(0.30 0.60)
Feed rate
(Min. Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)
2225
1775
1425
1500
1170
930
1015
805
665
(0.10 0.20)
(0.15 0.25)
(0.15 0.25)
(0.20 0.30)
(0.20 0.30)
(0.22 0.32)
(0.26 0.35)
(0.27 0.38)
(0.30 0.40)
Feed rate
(Min. Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)
Drill Dia.
DC
(m/min)
(min-1)
(mm)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
1935
2060
1640
1750
1375
1185
1260
1155
980
Drill Dia.
DC
(m/min)
(min-1)
(mm)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
(0.10 0.20)
(0.15 0.25)
(0.15 0.25)
(0.20 0.30)
(0.20 0.30)
(0.22 0.32)
(0.26 0.35)
(0.27 0.38)
(0.30 0.40)
Feed rate
(Min. Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)
0.1
0.1
0.1
0.15
0.2
0.2
0.25
0.25
0.3
(0.06 0.15)
(0.06 0.15)
(0.06 0.15)
(0.10 0.20)
(0.10 0.25)
(0.10 0.25)
(0.20 0.30)
(0.20 0.30)
(0.20 0.35)
Table Feed
(mm/min)
1485
1580
1260
1625
1275
1105
1110
955
805
Table Feed
(mm/min)
3050
2435
2100
1980
1645
1640
1755
1550
1250
Table Feed
(mm/min)
740
590
470
630
660
540
625
525
510
DRILLING
Work
Material
(Note 1) Spindle through & high pressure coolant system is recommended to make stable holes.
(Note 2) Emulsion type of water coolant is recommended.
N067
CARBIDE
MQS
WSTAR DRILLS
y M.Q.L.
Work
Material
Dia.
DC
(mm)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
Work
Material
Dia.
DC
(mm)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
Work
Material
DRILLING
Dia.
DC
(mm)
N068
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
AISI 1010 etc

Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(min-1)
100
100
100
110
110
110
130
140
140
9900
7900
6300
5500
4300
3500
3400
2700
2200
0.15
0.2
0.2
0.25
0.25
0.27
0.3
0.33
0.35
(0.10 0.20)
(0.15 0.25)
(0.15 0.25)
(0.20 0.30)
(0.20 0.30)
(0.22 0.32)
(0.26 0.35)
(0.27 0.38)
(0.30 0.40)
1485
1580
1260
1375
1075
945
1020
890
770
80
80
80
100
100
100
110
120
120
7900
6300
5000
5000
3900
3100
2900
2300
1900
AISI 4340 etc
No 45 B etc
Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(min-1)
60
60
60
60
60
60
80
80
80
5900
4700
3800
3000
2300
1900
2100
1500
1200
0.1
0.11
0.14
0.18
0.21
0.23
0.26
0.28
0.3
(0.06 0.15)
(0.07 0.15)
(0.09 0.18)
(0.11 0.24)
(0.16 0.25)
(0.19 0.27)
(0.22 0.30)
(0.23 0.33)
(0.26 0.35)
590
515
530
540
480
435
545
420
360
90
90
90
100
100
100
120
130
130
8900
7100
5700
5000
3900
3100
3100
2500
2000
60-40-8 etc
100-70-03 etc
Feed rate
(Min.Max.)
(mm/rev)
70
70
70
80
80
80
90
100
100
6900
5500
4400
4000
3100
2500
2300
1900
1500
0.25
0.25
0.25
0.3
0.3
0.3
0.35
0.35
0.35
(0.15 0.32)
(0.15 0.32)
(0.15 0.32)
(0.20 0.38)
(0.20 0.38)
(0.22 0.38)
(0.26 0.40)
(0.28 0.40)
(0.30 0.40)
0.15
0.2
0.2
0.25
0.25
0.27
0.3
0.33
0.35
0.28
0.28
0.3
0.33
0.35
0.4
0.45
0.5
0.5
60
60
60
70
70
70
80
90
90
5900
4700
3800
3500
2700
2200
2100
1700
1400
(0.15 0.35)
(0.15 0.35)
(0.15 0.40)
(0.20 0.45)
(0.20 0.45)
(0.22 0.45)
(0.26 0.50)
(0.28 0.60)
(0.30 0.60)
Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)
1725
1375
1100
1200
930
750
805
665
525
(0.10 0.20)
(0.15 0.25)
(0.15 0.25)
(0.20 0.30)
(0.20 0.30)
(0.22 0.32)
(0.26 0.35)
(0.27 0.38)
(0.30 0.40)
Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)

(m/min)
(min-1)
Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)
0.1
0.1
0.1
0.15
0.2
0.2
0.25
0.25
0.3
(0.06 0.15)
(0.06 0.15)
(0.06 0.15)
(0.10 0.20)
(0.10 0.25)
(0.10 0.25)
(0.20 0.30)
(0.20 0.30)
(0.20 0.35)
Table Feed
(mm/min)
1185
1260
1000
1250
975
835
870
755
665
Table Feed
(mm/min)
2490
1985
1710
1650
1365
1240
1395
1250
1000
Table Feed
(mm/min)
590
470
380
525
540
440
525
425
420
CARBIDE
y Operation Guidance for....X3DB....X5DB and....X8DB
Drill Length

Through Coolant Type (MQS)
Run-out < 0.03mm
Revolving
Coolant
Machine Type

0.5MPa7MPa
Thin Workpiece
Stepped Holes
DC
A > DC x 1.5
Coolant Handling
<MQS Type>

coolant exchange is
recommended.
Interrupted Cutting
One Process
If Bending
Occurs
zLower the feed

when drilling
the interrupted
part.
Requires Prior
Machining
Support
the Workpiece
zSpot face with

an end mill
prior to drilling.


cutting.
xAdd a 45chamfer.
DRILLING
Spindles
Through
Coolant Type
Drill Installation
Adjusting Screw
Drill Holding
N069
MMS
WSTAR DRILLS
P
aNew grade DP7020, unique coolant system, special fine margin.

aLong tool life and high efficiency drilling for stainless steel.
DC=3
0
0.014
Stainless Steel
h6
3<DC < 6 6<DC < 10 10<DC < 1818<DC < 20

0
0.018
0
0.008
0
0.027
0
0.011
0
0.033
0
0.013
LF
140
DC(h8)
PL
0
0.022
0
0.009
DCON(h6)
CARBIDE
LCF
LH
OAL
(Note) MMS drills are suitable for use with shrink fit holders.
3.5
3
5
3.6
3
5
3.7
3
5
3.8
3
5
3.9
3
5
4.0
3
5
4.1
3
5
4.2
3
5
4.3
3
5
4.4
3
5
4.5
3
5
4.6
3
5
4.7
3
5
4.8
3
5
DRILLING
21.6 23.6 70.6 70

28.6 31.6 78.6 78
0.6
0.6
6
6
5.0
3
5
21.6 23.6 70.6 70

28.6 31.6 78.6 78
0.6
0.6
6
6
5.1
3
5
21.6 23.6 70.6 70

28.6 31.6 78.6 78
0.6
0.6
6
6
5.2
3
5
21.6 23.6 70.6 70

28.6 31.6 78.6 78
0.6
0.6
6
6
5.3
3
5
21.6 23.6 70.6 70

28.6 31.6 78.6 78
0.6
0.6
6
6
5.4
3
5
22.7 23.7 70.7 70

30.7 31.7 78.7 78
0.7
0.7
6
6
5.5
3
5
22.7 23.7 70.7 70

30.7 31.7 78.7 78
0.7
0.7
6
6
5.6
3
5
22.7 23.7 70.7 70

30.7 31.7 78.7 78
0.7
0.7
6
6
5.7
3
5
22.7 23.7 70.7 70

30.7 31.7 78.7 78
0.7
0.7
6
6
5.8
3
5
22.7 23.7 70.7 70

30.7 31.7 78.7 78
0.7
0.7
6
6
5.9
3
5
24.7 26.7 73.7 73

33.7 35.7 82.7 82
0.7
0.7
6
6
6.0
3
5
24.8 26.8 73.8 73

33.8 35.8 82.8 82
0.8
0.8
6
6
6.1
3
5
24.8 26.8 73.8 73

33.8 35.8 82.8 82
0.8
0.8
6
6
6.2
3
5
24.8 26.8 73.8 73

33.8 35.8 82.8 82
0.8
0.8
6
6
6.3
3
5
24.8 26.8 73.8 73

33.8 35.8 82.8 82
0.8
0.8
6
6
6.4
3
5
25.8 28.8 75.8 75

35.8 38.8 85.8 85
0.8
0.8
6
6
6.5
3
5
25.9 28.9 75.9 75

35.9 38.9 85.9 85
0.9
0.9
6
6
6.6
3
5
25.9 28.9 75.9 75

35.9 38.9 85.9 85
0.9
0.9
6
6
6.7
3
5
MMS0490X3DB
MMS0490X5DB
MMS0500X3DB
MMS0500X5DB
MMS0510X3DB
MMS0510X5DB
MMS0520X3DB
MMS0520X5DB
MMS0530X3DB
MMS0530X5DB
MMS0540X3DB
MMS0540X5DB
MMS0550X3DB
MMS0550X5DB
MMS0560X3DB
MMS0560X5DB
MMS0570X3DB
MMS0570X5DB
MMS0580X3DB
MMS0580X5DB
MMS0590X3DB
MMS0590X5DB
MMS0600X3DB
MMS0600X5DB
MMS0610X3DB
MMS0610X5DB
MMS0620X3DB
MMS0620X5DB
MMS0630X3DB
MMS0630X5DB
MMS0640X3DB
MMS0640X5DB
MMS0650X3DB
MMS0650X5DB
MMS0660X3DB
MMS0660X5DB
MMS0670X3DB
MMS0670X5DB
N070
DCON
3
5
PL
3.4
3
5
LF
4.9
(mm) (l/d)
25.9 28.9 75.9 75

35.9 38.9 85.9 85
0.9
0.9
6
6
25.9 28.9 75.9 75

35.9 38.9 85.9 85
0.9
0.9
6
6
28.9 30.9 81.9 81

39.9 42.9 89.9 89
0.9
0.9
6
6
28.9 30.9 81.9 81

39.9 42.9 89.9 89
0.9
0.9
6
6
29.0 31.0 82.0 81

40.0 43.0 90.0 89
1.0
1.0
6
6
29.0 31.0 82.0 81

40.0 43.0 90.0 89
1.0
1.0
6
6
29.0 31.0 82.0 81

40.0 43.0 90.0 89
1.0
1.0
6
6
31.0 31.0 82.0 81

43.0 43.0 90.0 89
1.0
1.0
6
6
31.0 31.0 82.0 81

43.0 43.0 90.0 89
1.0
1.0
6
6
31.1 31.1 82.1 81

43.1 43.1 90.1 89
1.1
1.1
6
6
31.1 31.1 82.1 81

43.1 43.1 90.1 89
1.1
1.1
6
6
31.1 31.1 82.1 81

43.1 43.1 90.1 89
1.1
1.1
6
6
34.1 36.1 87.1 86

47.1 49.1 96.1 95
1.1
1.1
8
8
34.1 36.1 87.1 86

47.1 49.1 96.1 95
1.1
1.1
8
8
34.1 36.1 87.1 86

47.1 49.1 96.1 95
1.1
1.1
8
8
34.2 36.2 87.2 86

47.2 49.2 96.2 95
1.2
1.2
8
8
34.2 36.2 87.2 86

47.2 49.2 96.2 95
1.2
1.2
8
8
36.2 38.2 91.2 90

50.2 52.2 99.2 98
1.2
1.2
8
8
36.2 38.2 91.2 90

50.2 52.2 99.2 98
1.2
1.2
8
8
OAL
3
5
6
6
LH
3.3
0.5
0.5
LCF
DP7020
3
5
Hole Depth
3.2
DCON
PL
3
5
LF
3.1
MMS0300X3DB
MMS0300X5DB
MMS0310X3DB
MMS0310X5DB
MMS0320X3DB
MMS0320X5DB
MMS0330X3DB
MMS0330X5DB
MMS0340X3DB
MMS0340X5DB
MMS0350X3DB
MMS0350X5DB
MMS0360X3DB
MMS0360X5DB
MMS0370X3DB
MMS0370X5DB
MMS0380X3DB
MMS0380X5DB
MMS0390X3DB
MMS0390X5DB
MMS0400X3DB
MMS0400X5DB
MMS0410X3DB
MMS0410X5DB
MMS0420X3DB
MMS0420X5DB
MMS0430X3DB
MMS0430X5DB
MMS0440X3DB
MMS0440X5DB
MMS0450X3DB
MMS0450X5DB
MMS0460X3DB
MMS0460X5DB
MMS0470X3DB
MMS0470X5DB
MMS0480X3DB
MMS0480X5DB
21.5 23.5 70.5 70

28.5 31.5 78.5 78
OAL
LH
3
3.0
5
DC
Dimensions (mm)
Stock
Order Number
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
Stock
DP7020
DC
Hole Depth
Internal Coolant
When looking at the coating the color can vary depending on the direction
of viewing. This does not have any effect on the performance of the drill.
CARBIDE
7.3
3
5
7.4
3
5
7.5
3
5
7.6
3
5
7.7
3
5
7.8
3
5
7.9
3
5
8.0
3
5
8.1
3
5
8.2
3
5
8.3
3
5
8.4
3
5
8.5
3
5
8.6
3
5
8.7
3
5
8.8
3
5
8.9
3
5
9.0
3
5
9.1
3
5
9.2
3
5
9.4
3
5
36.3 38.3 91.3 90 1.3

50.3 52.3 99.3 98 1.3
8
8
9.5
3
5
39.3 40.3 91.3 90 1.3

54.3 57.3 104.3 103 1.3
8
8
9.6
3
5
39.3 40.3 91.3 90 1.3

54.3 57.3 104.3 103 1.3
8
8
9.7
3
5
39.3 40.3 91.3 90 1.3

54.3 57.3 104.3 103 1.3
8
8
9.8
3
5
39.3 40.3 91.3 90 1.3

54.3 57.3 104.3 103 1.3
8
8
9.9
3
5
39.4 40.4 91.4 90 1.4

54.4 57.4 104.4 103 1.4
8
8
10.0
3
5
41.4 41.4 91.4 90 1.4

57.4 57.4 104.4 103 1.4
8
8
10.1
3
5
41.4 41.4 91.4 90 1.4

57.4 57.4 104.4 103 1.4
8
8
10.2
3
5
41.4 41.4 91.4 90 1.4

57.4 57.4 104.4 103 1.4
8
8
10.3
3
5
41.4 41.4 91.4 90 1.4

57.4 57.4 104.4 103 1.4
8
8
10.4
3
5
41.5 41.5 91.5 90 1.5

57.5 57.5 104.5 103 1.5
8
8
10.5
3
5
44.5 46.5 97.5 96 1.5

61.5 63.5 114.5 113 1.5
10
10
10.6
3
5
44.5 46.5 97.5 96 1.5

61.5 63.5 114.5 113 1.5
10
10
10.7
3
5
44.5 46.5 97.5 96 1.5

61.5 63.5 114.5 113 1.5
10
10
10.8
3
5
44.5 46.5 97.5 96 1.5

61.5 63.5 114.5 113 1.5
10
10
10.9
3
5
44.5 46.5 97.5 96 1.5

61.5 63.5 114.5 113 1.5
10
10
11.0
3
5
46.6 48.6 102.6 101 1.6

64.6 66.6 117.6 116 1.6
10
10
11.1
3
5
46.6 48.6 102.6 101 1.6

64.6 66.6 117.6 116 1.6
10
10
11.2
3
5
46.6 48.6 102.6 101 1.6

64.6 66.6 117.6 116 1.6
10
10
11.3
3
5
46.6 48.6 102.6 101 1.6

64.6 66.6 117.6 116 1.6
10
10
11.4
3
5
46.6 48.6 102.6 101 1.6

64.6 66.6 117.6 116 1.6
10
10
11.5
3
5
49.7 51.7 102.7 101 1.7

68.7 71.7 122.7 121 1.7
10
10
11.6
3
5
49.7 51.7 102.7 101 1.7

68.7 71.7 122.7 121 1.7
10
10
11.7
3
5
49.7 51.7 102.7 101 1.7

68.7 71.7 122.7 121 1.7
10
10
49.7 51.7 102.7 101 1.7

68.7 71.7 122.7 121 1.7
10
10
49.7 51.7 102.7 101 1.7

68.7 71.7 122.7 121 1.7
10
10
51.7 51.7 102.7 101 1.7

71.7 71.7 122.7 121 1.7
10
10
51.8 51.8 102.8 101 1.8

71.8 71.8 122.8 121 1.8
10
10
51.8 51.8 102.8 101 1.8

71.8 71.8 122.8 121 1.8
10
10
51.8 51.8 102.8 101 1.8

71.8 71.8 122.8 121 1.8
10
10
51.8 51.8 102.8 101 1.8

71.8 71.8 122.8 121 1.8
10
10
54.8 56.8 112.8 111 1.8

75.8 79.8 135.8 134 1.8
12
12
54.9 56.9 112.9 111 1.9

75.9 79.9 135.9 134 1.9
12
12
54.9 56.9 112.9 111 1.9

75.9 79.9 135.9 134 1.9
12
12
54.9 56.9 112.9 111 1.9

75.9 79.9 135.9 134 1.9
12
12
54.9 56.9 112.9 111 1.9

75.9 79.9 135.9 134 1.9
12
12
56.9 57.9 117.9 116 1.9

78.9 79.9 135.9 134 1.9
12
12
56.9 57.9 117.9 116 1.9

78.9 79.9 135.9 134 1.9
12
12
57.0 58.0 118.0 116 2.0

79.0 80.0 136.0 134 2.0
12
12
57.0 58.0 118.0 116 2.0

79.0 80.0 136.0 134 2.0
12
12
57.0 58.0 118.0 116 2.0

79.0 80.0 136.0 134 2.0
12
12
60.0 62.0 118.0 116 2.0

83.0 86.0 142.0 140 2.0
12
12
60.0 62.0 118.0 116 2.0

83.0 86.0 142.0 140 2.0
12
12
60.1 62.1 118.1 116 2.1

83.1 86.1 142.1 140 2.1
12
12
60.1 62.1 118.1 116 2.1

83.1 86.1 142.1 140 2.1
12
12
60.1 62.1 118.1 116 2.1

83.1 86.1 142.1 140 2.1
12
12
62.1 62.1 118.1 116 2.1

86.1 86.1 142.1 140 2.1
12
12
62.1 62.1 118.1 116 2.1

86.1 86.1 142.1 140 2.1
12
12
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N074
N076
Q001
DRILLING
8
8
DCON
3
5
36.3 38.3 91.3 90 1.3

50.3 52.3 99.3 98 1.3
MMS0930X3DB
MMS0930X5DB
MMS0940X3DB
MMS0940X5DB
MMS0950X3DB
MMS0950X5DB
MMS0960X3DB
MMS0960X5DB
MMS0970X3DB
MMS0970X5DB
MMS0980X3DB
MMS0980X5DB
MMS0990X3DB
MMS0990X5DB
MMS1000X3DB
MMS1000X5DB
MMS1010X3DB
MMS1010X5DB
MMS1020X3DB
MMS1020X5DB
MMS1030X3DB
MMS1030X5DB
MMS1040X3DB
MMS1040X5DB
MMS1050X3DB
MMS1050X5DB
MMS1060X3DB
MMS1060X5DB
MMS1070X3DB
MMS1070X5DB
MMS1080X3DB
MMS1080X5DB
MMS1090X3DB
MMS1090X5DB
MMS1100X3DB
MMS1100X5DB
MMS1110X3DB
MMS1110X5DB
MMS1120X3DB
MMS1120X5DB
MMS1130X3DB
MMS1130X5DB
MMS1140X3DB
MMS1140X5DB
MMS1150X3DB
MMS1150X5DB
MMS1160X3DB
MMS1160X5DB
MMS1170X3DB
MMS1170X5DB
PL
7.2
LF
3
5
OAL
3
5
9.3
(mm) (l/d)
LH
7.1
8
8
LCF
DP7020
3
5
Hole Depth
7.0
DCON
PL
3
5
36.2 38.2 91.2 90 1.2

50.2 52.2 99.2 98 1.2
LF
6.9
MMS0680X3DB
MMS0680X5DB
MMS0690X3DB
MMS0690X5DB
MMS0700X3DB
MMS0700X5DB
MMS0710X3DB
MMS0710X5DB
MMS0720X3DB
MMS0720X5DB
MMS0730X3DB
MMS0730X5DB
MMS0740X3DB
MMS0740X5DB
MMS0750X3DB
MMS0750X5DB
MMS0760X3DB
MMS0760X5DB
MMS0770X3DB
MMS0770X5DB
MMS0780X3DB
MMS0780X5DB
MMS0790X3DB
MMS0790X5DB
MMS0800X3DB
MMS0800X5DB
MMS0810X3DB
MMS0810X5DB
MMS0820X3DB
MMS0820X5DB
MMS0830X3DB
MMS0830X5DB
MMS0840X3DB
MMS0840X5DB
MMS0850X3DB
MMS0850X5DB
MMS0860X3DB
MMS0860X5DB
MMS0870X3DB
MMS0870X5DB
MMS0880X3DB
MMS0880X5DB
MMS0890X3DB
MMS0890X5DB
MMS0900X3DB
MMS0900X5DB
MMS0910X3DB
MMS0910X5DB
MMS0920X3DB
MMS0920X5DB
OAL
LH
3
6.8
5
DC
Dimensions (mm)
Stock
Order Number
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
DP7020
DC
Hole Depth
Internal Coolant
Stock
N071
MMS
WSTAR DRILLS
3
5
12.3
3
5
12.4
3
5
12.5
3
5
12.6
3
5
12.7
3
5
12.8
3
5
12.9
3
5
13.0
3
5
13.1
3
5
13.2
3
5
13.3
3
5
13.4
3
5
13.5
3
5
13.6
3
5
13.7
3
5
13.8
3
5
13.9
3
5
14.0
3
5
14.1
3
5
14.2
3
5
DRILLING
62.2 62.2 118.2 116 2.2

86.2 86.2 142.2 140 2.2
12
12
14.4
3
5
62.2 62.2 118.2 116 2.2

86.2 86.2 142.2 140 2.2
12
12
14.5
3
5
65.2 68.2 124.2 122 2.2

90.2 94.2 150.2 148 2.2
14
14
14.6
3
5
65.2 68.2 124.2 122 2.2

90.2 94.2 150.2 148 2.2
14
14
14.7
3
5
65.2 68.2 124.2 122 2.2

90.2 94.2 150.2 148 2.2
14
14
14.8
3
5
65.3 68.3 124.3 122 2.3

90.3 94.3 150.3 148 2.3
14
14
14.9
3
5
65.3 68.3 124.3 122 2.3

90.3 94.3 150.3 148 2.3
14
14
15.0
3
5
67.3 68.3 124.3 122 2.3

93.3 94.3 150.3 148 2.3
14
14
15.1
3
5
67.3 68.3 124.3 122 2.3

93.3 94.3 150.3 148 2.3
14
14
15.2
3
5
67.3 68.3 124.3 122 2.3

93.3 94.3 150.3 148 2.3
14
14
15.3
3
5
67.3 68.3 124.3 122 2.3

93.3 94.3 150.3 148 2.3
14
14
15.4
3
5
67.4 68.4 124.4 122 2.4

93.4 94.4 150.4 148 2.4
14
14
15.5
3
5
70.4 72.4 128.4 126 2.4

97.4 100.4 156.4 154 2.4
14
14
15.6
3
5
70.4 72.4 128.4 126 2.4

97.4 100.4 156.4 154 2.4
14
14
15.7
3
5
70.4 72.4 128.4 126 2.4

97.4 100.4 156.4 154 2.4
14
14
15.8
3
5
70.4 72.4 128.4 126 2.4

97.4 100.4 156.4 154 2.4
14
14
15.9
3
5
70.5 72.5 128.5 126 2.5

97.5 100.5 156.5 154 2.5
14
14
16.0
3
5
72.5 72.5 128.5 126 2.5

100.5 100.5 156.5 154 2.5
14
14
16.1
3
5
72.5 72.5 128.5 126 2.5

100.5 100.5 156.5 154 2.5
14
14
16.2
3
5
72.5 72.5 128.5 126 2.5

100.5 100.5 156.5 154 2.5
14
14
16.3
3
5
72.5 72.5 128.5 126 2.5

100.5 100.5 156.5 154 2.5
14
14
16.4
3
5
72.5 72.5 128.5 126 2.5

100.5 100.5 156.5 154 2.5
14
14
16.5
3
5
75.6 78.6 137.6 135 2.6

104.6 108.6 167.6 165 2.6
16
16
16.6
3
5
75.6 78.6 137.6 135 2.6

104.6 108.6 167.6 165 2.6
16
16
16.7
3
5
MMS1430X3DB
MMS1430X5DB
MMS1440X3DB
MMS1440X5DB
MMS1450X3DB
MMS1450X5DB
MMS1460X3DB
MMS1460X5DB
MMS1470X3DB
MMS1470X5DB
MMS1480X3DB
MMS1480X5DB
MMS1490X3DB
MMS1490X5DB
MMS1500X3DB
MMS1500X5DB
MMS1510X3DB
MMS1510X5DB
MMS1520X3DB
MMS1520X5DB
MMS1530X3DB
MMS1530X5DB
MMS1540X3DB
MMS1540X5DB
MMS1550X3DB
MMS1550X5DB
MMS1560X3DB
MMS1560X5DB
MMS1570X3DB
MMS1570X5DB
MMS1580X3DB
MMS1580X5DB
MMS1590X3DB
MMS1590X5DB
MMS1600X3DB
MMS1600X5DB
MMS1610X3DB
MMS1610X5DB
MMS1620X3DB
MMS1620X5DB
MMS1630X3DB
MMS1630X5DB
MMS1640X3DB
MMS1640X5DB
MMS1650X3DB
MMS1650X5DB
MMS1660X3DB
MMS1660X5DB
MMS1670X3DB
MMS1670X5DB
N072
DCON
12.2
PL
3
5
75.6 78.6 137.6 135 2.6

104.6 108.6 167.6 165 2.6
16
16
75.6 78.6 137.6 135 2.6

104.6 108.6 167.6 165 2.6
16
16
75.6 78.6 137.6 135 2.6

104.6 108.6 167.6 165 2.6
16
16
77.7 78.7 137.7 135 2.7

107.7 108.7 167.7 165 2.7
16
16
77.7 78.7 137.7 135 2.7

107.7 108.7 167.7 165 2.7
16
16
77.7 78.7 137.7 135 2.7

107.7 108.7 167.7 165 2.7
16
16
77.7 78.7 137.7 135 2.7

107.7 108.7 167.7 165 2.7
16
16
77.7 78.7 137.7 135 2.7

107.7 108.7 167.7 165 2.7
16
16
80.7 82.7 141.7 139 2.7

111.7 114.7 173.7 171 2.7
16
16
80.8 82.8 141.8 139 2.8

111.8 114.8 173.8 171 2.8
16
16
80.8 82.8 141.8 139 2.8

111.8 114.8 173.8 171 2.8
16
16
80.8 82.8 141.8 139 2.8

111.8 114.8 173.8 171 2.8
16
16
80.8 82.8 141.8 139 2.8

111.8 114.8 173.8 171 2.8
16
16
82.8 82.8 141.8 139 2.8

114.8 114.8 173.8 171 2.8
16
16
82.9 82.9 141.9 139 2.9

114.9 114.9 173.9 171 2.9
16
16
82.9 82.9 141.9 139 2.9

114.9 114.9 173.9 171 2.9
16
16
82.9 82.9 141.9 139 2.9

114.9 114.9 173.9 171 2.9
16
16
82.9 82.9 141.9 139 2.9

114.9 114.9 173.9 171 2.9
16
16
85.9 88.9 147.9 145 2.9

118.9 122.9 181.9 179 2.9
18
18
85.9 88.9 147.9 145 2.9

118.9 122.9 181.9 179 2.9
18
18
86.0 89.0 148.0 145 3.0

119.0 123.0 182.0 179 3.0
18
18
86.0 89.0 148.0 145 3.0

119.0 123.0 182.0 179 3.0
18
18
86.0 89.0 148.0 145 3.0

119.0 123.0 182.0 179 3.0
18
18
88.0 89.0 148.0 145 3.0

122.0 123.0 182.0 179 3.0
18
18
88.0 89.0 148.0 145 3.0

122.0 123.0 182.0 179 3.0
18
18
LF
3
5
14.3
(mm) (l/d)
OAL
12.1
12
12
LH
DP7020
3
5
Hole Depth
12.0
DCON
PL
3
5
62.1 62.1 118.1 116 2.1

86.1 86.1 142.1 140 2.1
LF
11.9
MMS1180X3DB
MMS1180X5DB
MMS1190X3DB
MMS1190X5DB
MMS1200X3DB
MMS1200X5DB
MMS1210X3DB
MMS1210X5DB
MMS1220X3DB
MMS1220X5DB
MMS1230X3DB
MMS1230X5DB
MMS1240X3DB
MMS1240X5DB
MMS1250X3DB
MMS1250X5DB
MMS1260X3DB
MMS1260X5DB
MMS1270X3DB
MMS1270X5DB
MMS1280X3DB
MMS1280X5DB
MMS1290X3DB
MMS1290X5DB
MMS1300X3DB
MMS1300X5DB
MMS1310X3DB
MMS1310X5DB
MMS1320X3DB
MMS1320X5DB
MMS1330X3DB
MMS1330X5DB
MMS1340X3DB
MMS1340X5DB
MMS1350X3DB
MMS1350X5DB
MMS1360X3DB
MMS1360X5DB
MMS1370X3DB
MMS1370X5DB
MMS1380X3DB
MMS1380X5DB
MMS1390X3DB
MMS1390X5DB
MMS1400X3DB
MMS1400X5DB
MMS1410X3DB
MMS1410X5DB
MMS1420X3DB
MMS1420X5DB
OAL
LH
3
11.8
5
DC
Dimensions (mm)
Stock
Order Number
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
DP7020
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
CARBIDE
17.3
3
5
17.4
3
5
17.5
3
5
17.6
3
5
17.7
3
5
17.8
3
5
17.9
3
5
18.0
3
5
18.1
3
5
18.2
3
5
18.3
3
5
18.4
3
5
18.5
3
5
18.6
3
5
18.7
3
5
18.8
3
5
18.9
3
5
19.0
3
5
19.1
3
5
19.2
3
5
19.4
3
5
88.1 89.1 148.1 145 3.1

122.1 123.1 182.1 179 3.1
18
18
19.5
3
5
91.1 93.1 152.1 149 3.1

126.1 129.1 188.1 185 3.1
18
18
19.6
3
5
91.1 93.1 152.1 149 3.1

126.1 129.1 188.1 185 3.1
18
18
19.7
3
5
91.1 93.1 152.1 149 3.1

126.1 129.1 188.1 185 3.1
18
18
19.8
3
5
91.2 93.2 152.2 149 3.2

126.2 129.2 188.2 185 3.2
18
18
19.9
3
5
91.2 93.2 152.2 149 3.2

126.2 129.2 188.2 185 3.2
18
18
20.0
3
5
93.2 93.2 152.2 149 3.2

129.2 129.2 188.2 185 3.2
18
18
93.2 93.2 152.2 149 3.2

129.2 129.2 188.2 185 3.2
18
18
93.2 93.2 152.2 149 3.2

129.2 129.2 188.2 185 3.2
18
18
93.3 93.3 152.3 149 3.3

129.3 129.3 188.3 185 3.3
18
18
93.3 93.3 152.3 149 3.3

129.3 129.3 188.3 185 3.3
18
18
96.3 99.3 160.3 157 3.3

133.3 137.3 198.3 195 3.3
20
20
96.3 99.3 160.3 157 3.3

133.3 137.3 198.3 195 3.3
20
20
96.3 99.3 160.3 157 3.3

133.3 137.3 198.3 195 3.3
20
20
96.3 99.3 160.3 157 3.3

133.3 137.3 198.3 195 3.3
20
20
96.4 99.4 160.4 157 3.4

133.4 137.4 198.4 195 3.4
20
20
98.4 99.4 160.4 157 3.4

136.4 137.4 198.4 195 3.4
20
20
98.4 99.4 160.4 157 3.4

136.4 137.4 198.4 195 3.4
20
20
98.4 99.4 160.4 157 3.4

136.4 137.4 198.4 195 3.4
20
20
98.4 99.4 160.4 157 3.4

136.4 137.4 198.4 195 3.4
20
20
98.5 99.5 160.5 157 3.5

136.5 137.5 198.5 195 3.5
20
20
101.5 103.5 164.5 161 3.5

140.5 143.5 204.5 201 3.5
20
20
101.5 103.5 164.5 161 3.5

140.5 143.5 204.5 201 3.5
20
20
101.5 103.5 164.5 161 3.5

140.5 143.5 204.5 201 3.5
20
20
101.5 103.5 164.5 161 3.5

140.5 143.5 204.5 201 3.5
20
20
101.5 103.5 164.5 161 3.5

140.5 143.5 204.5 201 3.5
20
20
103.6 103.6 164.6 161 3.6

143.6 143.6 204.6 201 3.6
20
20
103.6 103.6 164.6 161 3.6

143.6 143.6 204.6 201 3.6
20
20
103.6 103.6 164.6 161 3.6

143.6 143.6 204.6 201 3.6
20
20
103.6 103.6 164.6 161 3.6

143.6 143.6 204.6 201 3.6
20
20
103.6 103.6 164.6 161 3.6

143.6 143.6 204.6 201 3.6
20
20
DRILLING
18
18
DCON
3
5
88.1 89.1 148.1 145 3.1

122.1 123.1 182.1 179 3.1
MMS1930X3DB
MMS1930X5DB
MMS1940X3DB
MMS1940X5DB
MMS1950X3DB
MMS1950X5DB
MMS1960X3DB
MMS1960X5DB
MMS1970X3DB
MMS1970X5DB
MMS1980X3DB
MMS1980X5DB
MMS1990X3DB
MMS1990X5DB
MMS2000X3DB
MMS2000X5DB
PL
17.2
LF
3
5
OAL
3
5
19.3
(mm) (l/d)
LH
17.1
18
18
LCF
DP7020
3
5
Hole Depth
17.0
DCON
PL
3
5
88.1 89.1 148.1 145 3.1

122.1 123.1 182.1 179 3.1
LF
16.9
MMS1680X3DB
MMS1680X5DB
MMS1690X3DB
MMS1690X5DB
MMS1700X3DB
MMS1700X5DB
MMS1710X3DB
MMS1710X5DB
MMS1720X3DB
MMS1720X5DB
MMS1730X3DB
MMS1730X5DB
MMS1740X3DB
MMS1740X5DB
MMS1750X3DB
MMS1750X5DB
MMS1760X3DB
MMS1760X5DB
MMS1770X3DB
MMS1770X5DB
MMS1780X3DB
MMS1780X5DB
MMS1790X3DB
MMS1790X5DB
MMS1800X3DB
MMS1800X5DB
MMS1810X3DB
MMS1810X5DB
MMS1820X3DB
MMS1820X5DB
MMS1830X3DB
MMS1830X5DB
MMS1840X3DB
MMS1840X5DB
MMS1850X3DB
MMS1850X5DB
MMS1860X3DB
MMS1860X5DB
MMS1870X3DB
MMS1870X5DB
MMS1880X3DB
MMS1880X5DB
MMS1890X3DB
MMS1890X5DB
MMS1900X3DB
MMS1900X5DB
MMS1910X3DB
MMS1910X5DB
MMS1920X3DB
MMS1920X5DB
OAL
LH
3
16.8
5
DC
Dimensions (mm)
Stock
Order Number
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
DP7020
DC
Hole Depth
Internal Coolant
Stock
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N074
N076
Q001
N073
CARBIDE
MMS
WSTAR DRILLS
Work
Material
Dia.
DC
(mm)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
Work
Material
Dia.
DC
(mm)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
Work
Material
DRILLING
Dia.
DC
(mm)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
Austenitic Stainless Steel (>200HB)
AISI 304LN, AISI 316LN etc

Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(min-1)
80
80
80
80
80
60
60
60
60
7900
6300
5000
4000
3100
1900
1500
1100
900
0.13
0.15
0.15
0.17
0.19
0.2
0.21
0.22
0.23
(0.08 0.18)
(0.10 0.20)
(0.10 0.20)
(0.12 0.22)
(0.14 0.24)
(0.15 0.25)
(0.16 0.26)
(0.17 0.27)
(0.18 0.28)
Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)
1025
945
750
680
585
380
315
240
205
60
60
60
60
60
50
50
50
50
5900
4700
3800
3000
2300
1500
1300
900
700
0.1
0.12
0.12
0.15
0.17
0.18
0.19
0.2
0.21
(0.05 0.15)
(0.08 0.18)
(0.08 0.18)
(0.1 0.2)
(0.12 0.22)
(0.13 0.23)
(0.14 0.24)
(0.15 0.25)
(0.16 0.26)
Duplex Steel ( < 280HB)
Ferritic, Precipitation hardening stainless steel ( < 200HB)
AISI 329 etc

Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(min-1)
50
50
50
50
50
40
40
40
40
4900
3900
3100
2500
1900
1200
1000
700
600
0.1
0.12
0.12
0.15
0.17
0.18
0.19
0.2
0.21
(0.05 0.15)
(0.08 0.18)
(0.08 0.18)
(0.1 0.2)
(0.12 0.22)
(0.13 0.23)
(0.14 0.24)
(0.15 0.25)
(0.16 0.26)
Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)
490
465
370
375
320
215
190
140
125
80
80
80
80
80
60
60
60
60
7900
6300
5000
4000
3100
1900
1500
1100
900
0.13
0.15
0.15
0.17
0.19
0.2
0.21
0.22
0.23
(0.08 0.18)
(0.10 0.20)
(0.10 0.20)
(0.12 0.22)
(0.14 0.24)
(0.15 0.25)
(0.16 0.26)
(0.17 0.27)
(0.18 0.28)
Ferritic, Precipitation hardening stainless steel (>200HB)
Precipitation hardening stainless steel (<450HB)
ASTM 630, ASTM 631 etc

Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(min-1)
60
60
60
60
60
50
50
50
50
5900
4700
3800
3000
2300
1500
1300
900
700
0.1
0.12
0.12
0.15
0.17
0.18
0.19
0.2
0.21
(0.05 0.15)
(0.08 0.18)
(0.08 0.18)
(0.1 0.2)
(0.12 0.22)
(0.13 0.23)
(0.14 0.24)
(0.15 0.25)
(0.16 0.26)
Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)
590
560
455
450
390
270
245
180
145
50
50
50
50
50
40
40
40
40
4900
3900
3100
2500
1900
1200
1000
700
600
0.1
0.12
0.12
0.15
0.17
0.18
0.19
0.2
0.21
(0.05 0.15)
(0.08 0.18)
(0.08 0.18)
(0.1 0.2)
(0.12 0.22)
(0.13 0.23)
(0.14 0.24)
(0.15 0.25)
(0.16 0.26)
Table Feed
(mm/min)
590
560
455
450
390
270
245
180
145
Table Feed
(mm/min)
1025
945
750
680
585
380
315
240
205
Table Feed
(mm/min)
490
465
370
375
320
215
190
140
125
(Note 1) For stable machining, internal coolant supply with high pressure is recommended.
(Note 2) Emulsion type of water coolant is recommended.
(Note 3) Recommended cutting conditions are for machining under the conditions of favourable machining environment and coolant. Please
lower the cutting conditions if there is a problem in the rigidity of machine and workpiece, and coolant property or discharge amount .
N074
CARBIDE
y Stainless Steel Cross Reference List
< 200HB
Ferritic,
Precipitation
hardening stainless steel
>200HB
Precipitation hardening
stainless steel
<450HB
< 200HB
Austenitic
Stainless Steel
>200HB
Duplex Steel
< 280HB
Japan
JIS
W-no.
Germany
USA
AISI/SAE
SUS416
1.4005
X12CrS3
416
SUS410
1.4006
X10Cr13
410
SUS430
1.4016
X6Cr17
430
SUS434
1.4113
X6CrMo17
434
SUS430LX
DIN
1.4510
X6CrTi17
430Ti
1.4512
X6CrTi12
409
SUS420J1
1.4021
X20Cr13
420
SUS431
1.4057
X20CrNi17-2
431
SUS420J2
1.4028
X30Cr13
420
SUS440C
1.4125
X10CrMo17
440C
SUS630
1.4542
X5CrNiCuNb16 4
1.4545
630 (17-4PH)
S15500 (15-5PH)
SUS631
1.4568
X7CrNiAl17 7
631 (17-7PH)
SUS304
1.4301
X5CrNi18 10
304
SUS305
1.4303
X5CrNi8-12
305
SUS303
1.4305
X12CrNiS18-9
303
SUS304L
1.4307
X2CrNi19-11
304L
SUS316
1.4401
X5CrNiMo17 12 2
316
SUS304LN
1.4311
X2CrNiN18 10
304LN
SUS316L
1.4404
X2CrNiMo17 12 2
316L
SUS316LN
1.4406
X2CrNiMoN17 12 2
316LN
SUS316L
1.4435
X2CrNiMo18 14 3
SUS317L
1.4438
X2CrNiMo18 15 4
317L
1.4529
X1NiCrMoCuN25 20 7
N08926
SUS321
1.4541
X6CrNiTi18-10
321
SUS347
1.4550
X6CrNiNb18-10
347
SUS316Ti
1.4571
X6CrNiMoTi17 12 2
316Ti
1.4362
X2CrNiN23 4
SCS14A
1.4410
X2CrNiMoN25 7 4
S32750
SUS329J1
1.4460
X3CrNiMoN27 5 2
329
SUS329J3L
1.4462
X2CrNiMoN22 5 3
S31803
DRILLING
Material
OPERATION GUIDANCE
TECHNICAL DATA
N076
Q001
N075
CARBIDE
MMS
WSTAR DRILLS
y Operation Guidance for....X3DB and....X5DB
Drill Length
Drill Installation
A > DC x 1.5
Run-out < 0.03mm
Coolant Handling
Thin Workpiece
Interrupted Cutting
Adjusting Screw
Drill Holding
DC

Through Coolant Type (MQS)

Spindles
Through
Coolant Type
Revolving
Coolant
Machine Type

0.5MPa7MPa
DRILLING
Stepped Holes
N076

<MMS Type>
(1)Small particles of swarf

will jam in the oil hole. Use
a filter as a preventative
measure. When using small
diameter drills, use a fine
mesh filter.
(2)Dirt and dust particles in old
coolant can clog the oil hole
and prevent effective flow.
Regular coolant exchange
is recommended.

cutting.
xAdd a 45chamfer.
One Process
If Bending
Occurs
zLower the feed

when drilling
the interrupted
part.
Requires Prior
Machining
Support
the Workpiece
zSpot face with

an end mill
prior to drilling.
SOLID CARBIDE DRILLS FOR MACHINING OF ALUMINIUM ALLOYS
MNS
WSTAR DRILLS
P
a4 holes special coolant system, good for resistance to adhesion.

aHigh efficiency drilling for aluminium alloy.
Non-ferrous Metal
h6
DC=3
3<DC < 6
6<DC < 10
10<DC < 14
0
0.014
0
0.006
0
0.018
0
0.008
0
0.022
0
0.009
0
0.027
0
0.011
DCON(h6)
LF
140
DC
PL
CARBIDE
LCF
LH
OAL
(Note 1) MNS drills are suitable for use with shrink fit holders.
(Note 2) 4.5 or smaller diameter drills are designed with 2 colant holes.
3.2
3.3
3.4
3.5
3.6
3.7
20
30
5
10
a
a
r
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
a
a
r
20
30
5
10
20
30
5
10
20
30
r
r
r
MNS0300LB
MNS0300X10DB
MNS0300X20DB
MNS0300X30DB
MNS0310LB
MNS0310X10DB
MNS0310X20DB
MNS0310X30DB
MNS0320LB
MNS0320X10DB
MNS0320X20DB
MNS0320X30DB
MNS0330LB
MNS0330X10DB
MNS0330X20DB
MNS0330X30DB
MNS0340LB
MNS0340X10DB
MNS0340X20DB
MNS0340X30DB
MNS0350LB
MNS0350X10DB
MNS0350X20DB
MNS0350X30DB
MNS0360LB
MNS0360X10DB
MNS0360X20DB
MNS0360X30DB
MNS0370LB
MNS0370X10DB
MNS0370X20DB
MNS0370X30DB
3
3
69.5 72.5 120.5 120 0.5

99.5 102.5 150.5 150 0.5
3
3
39.6 39.6 87.6 87 0.6

46.6 49.6 97.6 97 0.6
4
4
81.6 84.6 132.6 132 0.6

116.6 119.6 167.6 167 0.6
4
4
39.6 39.6 87.6 87 0.6

46.6 49.6 97.6 97 0.6
4
4
81.6 84.6 132.6 132 0.6

116.6 119.6 167.6 167 0.6
4
4
39.6 39.6 87.6 87 0.6

46.6 49.6 97.6 97 0.6
4
4
81.6 84.6 132.6 132 0.6

116.6 119.6 167.6 167 0.6
4
4
39.6 39.6 87.6 87 0.6

46.6 49.6 97.6 97 0.6
4
4
81.6 84.6 132.6 132 0.6

116.6 119.6 167.6 167 0.6
4
4
39.6 39.6 87.6 87 0.6

46.6 49.6 97.6 97 0.6
4
4
81.6 84.6 132.6 132 0.6

116.6 119.6 167.6 167 0.6
4
4
44.7 44.7 92.7 92 0.7

52.7 55.7 103.7 103 0.7
4
4
92.7 95.7 143.7 143 0.7

132.7 135.7 183.7 183 0.7
4
4
44.7 44.7 92.7 92 0.7

52.7 55.7 103.7 103 0.7
4
4
92.7 95.7 143.7 143 0.7

132.7 135.7 183.7 183 0.7
4
4
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
a
a
r
r
r
a
r
r
r
a
r
r
r
a
r
r
r
a
r
r
r
MNS0380LB
MNS0380X10DB
MNS0380X20DB
MNS0380X30DB
MNS0390LB
MNS0390X10DB
MNS0390X20DB
MNS0390X30DB
MNS0400LB
MNS0400X10DB
MNS0400X20DB
MNS0400X30DB
MNS0410LB
MNS0410X10DB
MNS0410X20DB
MNS0410X30DB
MNS0420LB
MNS0420X10DB
MNS0420X20DB
MNS0420X30DB
MNS0430LB
MNS0430X10DB
MNS0430X20DB
MNS0430X30DB
MNS0440LB
MNS0440X10DB
MNS0440X20DB
MNS0440X30DB
MNS0450LB
MNS0450X10DB
MNS0450X20DB
MNS0450X30DB
DCON
PL
LF
OAL
5
10
LH
(mm) (l/d)
Order Number
LCF
Hole Depth
DCON
PL
LF
OAL
LH
33.5 33.5 81.5 81 0.5

39.5 42.5 90.5 90 0.5
DC
44.7 44.7 92.7 92 0.7

52.7 55.7 103.7 103 0.7
4
4
92.7 95.7 143.7 143 0.7

132.7 135.7 183.7 183 0.7
4
4
44.7 44.7 92.7 92 0.7

52.7 55.7 103.7 103 0.7
4
4
92.7 95.7 143.7 143 0.7

132.7 135.7 183.7 183 0.7
4
4
44.7 44.7 92.7 92 0.7

52.7 55.7 103.7 103 0.7
4
4
92.7 95.7 143.7 143 0.7

132.7 135.7 183.7 183 0.7
4
4
50.7 50.7 100.7 100 0.7

59.7 62.7 112.7 112 0.7
5
5
104.7 107.7 157.7 157 0.7

149.7 152.7 202.7 202 0.7
5
5
50.8 50.8 100.8 100 0.8

59.8 62.8 112.8 112 0.8
5
5
104.8 107.8 157.8 157 0.8

149.8 152.8 202.8 202 0.8
5
5
50.8 50.8 100.8 100 0.8

59.8 62.8 112.8 112 0.8
5
5
104.8 107.8 157.8 157 0.8

149.8 152.8 202.8 202 0.8
5
5
50.8 50.8 100.8 100 0.8

59.8 62.8 112.8 112 0.8
5
5
104.8 107.8 157.8 157 0.8

149.8 152.8 202.8 202 0.8
5
5
50.8 50.8 100.8 100 0.8

59.8 62.8 112.8 112 0.8
5
5
104.8 107.8 157.8 157 0.8

149.8 152.8 202.8 202 0.8
5
5
DRILLING
3.1
5
10
Order Number
Dimensions (mm)
Stock
TF15
3.0
Internal Coolant
Dimensions (mm)
LCF
(mm) (l/d)
TF15
DC
Hole Depth
Internal Coolant
Stock
CUTTING CONDITIONS
a
OPERATION GUIDANCE
TECHNICAL DATA
N082
N083
Q001
N077
MNS
WSTAR DRILLS
4.7
4.8
4.9
5.0
5.1
5.2
5.3
DRILLING
5.4
5.5
5.6
5.7
20
30
5
10
20
30
5
10
a
r
r
r
a
r
r
r
a
r
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
a
a
r
r
r
a
r
r
r
a
r
20
30
5
10
20
30
5
10
20
30
5
10
20
30
a
a
r
r
r
a
r
r
r
MNS0460LB
MNS0460X10DB
MNS0460X20DB
MNS0460X30DB
MNS0470LB
MNS0470X10DB
MNS0470X20DB
MNS0470X30DB
MNS0480LB
MNS0480X10DB
MNS0480X20DB
MNS0480X30DB
MNS0490LB
MNS0490X10DB
MNS0490X20DB
MNS0490X30DB
MNS0500LB
MNS0500X10DB
MNS0500X20DB
MNS0500X30DB
MNS0510LB
MNS0510X10DB
MNS0510X20DB
MNS0510X30DB
MNS0520LB
MNS0520X10DB
MNS0520X20DB
MNS0520X30DB
MNS0530LB
MNS0530X10DB
MNS0530X20DB
MNS0530X30DB
MNS0540LB
MNS0540X10DB
MNS0540X20DB
MNS0540X30DB
MNS0550LB
MNS0550X10DB
MNS0550X20DB
MNS0550X30DB
MNS0560LB
MNS0560X10DB
MNS0560X20DB
MNS0560X30DB
MNS0570LB
MNS0570X10DB
MNS0570X20DB
MNS0570X30DB
55.8 55.8 105.8 105 0.8

65.8 68.8 118.8 118 0.8
5
5
115.8 118.8 168.8 168 0.8

165.8 168.8 218.8 218 0.8
5
5
55.9 55.9 105.9 105 0.9

65.9 68.9 118.9 118 0.9
5
5
115.9 118.9 168.9 168 0.9

165.9 168.9 218.9 218 0.9
5
5
55.9 55.9 105.9 105 0.9

65.9 68.9 118.9 118 0.9
5
5
115.9 118.9 168.9 168 0.9

165.9 168.9 218.9 218 0.9
5
5
55.9 55.9 105.9 105 0.9

65.9 68.9 118.9 118 0.9
5
5
115.9 118.9 168.9 168 0.9

165.9 168.9 218.9 218 0.9
5
5
44.9 44.9 100.9 100 0.9

65.9 68.9 118.9 118 0.9
6
5
115.9 118.9 168.9 168 0.9

165.9 168.9 218.9 218 0.9
5
5
44.9 44.9 100.9 100 0.9

72.9 75.9 127.9 127 0.9
6
6
127.9 130.9 182.9 182 0.9

182.9 185.9 237.9 237 0.9
6
6
44.9 44.9 100.9 100 0.9

72.9 75.9 127.9 127 0.9
6
6
127.9 130.9 182.9 182 0.9

182.9 185.9 237.9 237 0.9
6
6
45.0 45.0 101.0 100 1.0

73.0 76.0 128.0 127 1.0
6
6
128.0 131.0 183.0 182 1.0

183.0 186.0 238.0 237 1.0
6
6
45.0 45.0 101.0 100 1.0

73.0 76.0 128.0 127 1.0
6
6
128.0 131.0 183.0 182 1.0

183.0 186.0 238.0 237 1.0
6
6
45.0 45.0 101.0 100 1.0

73.0 76.0 128.0 127 1.0
6
6
128.0 131.0 183.0 182 1.0

183.0 186.0 238.0 237 1.0
6
6
49.0 49.0 101.0 100 1.0

79.0 82.0 134.0 133 1.0
6
6
139.0 142.0 194.0 193 1.0

199.0 202.0 254.0 253 1.0
6
6
49.0 49.0 101.0 100 1.0

79.0 82.0 134.0 133 1.0
6
6
139.0 142.0 194.0 193 1.0

199.0 202.0 254.0 253 1.0
6
6
5.8
5.9
6.0
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
20
30
5
10
r
r
a
r
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
a
a
r
r
r
a
r
r
r
a
r
20
30
5
10
20
30
5
10
a
a
r
20
30
5
10
20
30
5
10
20
30
5
10
20
30
a
a
r
r
r
a
r
r
r
MNS0580LB
MNS0580X10DB
MNS0580X20DB
MNS0580X30DB
MNS0590LB
MNS0590X10DB
MNS0590X20DB
MNS0590X30DB
MNS0600LB
MNS0600X10DB
MNS0600X20DB
MNS0600X30DB
MNS0610LB
MNS0610X10DB
MNS0610X20DB
MNS0610X30DB
MNS0620LB
MNS0620X10DB
MNS0620X20DB
MNS0620X30DB
MNS0630LB
MNS0630X10DB
MNS0630X20DB
MNS0630X30DB
MNS0640LB
MNS0640X10DB
MNS0640X20DB
MNS0640X30DB
MNS0650LB
MNS0650X10DB
MNS0650X20DB
MNS0650X30DB
MNS0660LB
MNS0660X10DB
MNS0660X20DB
MNS0660X30DB
MNS0670LB
MNS0670X10DB
MNS0670X20DB
MNS0670X30DB
MNS0680LB
MNS0680X10DB
MNS0680X20DB
MNS0680X30DB
MNS0690LB
MNS0690X10DB
MNS0690X20DB
MNS0690X30DB
N078
DCON
PL
LF
5
10
OAL
(mm) (l/d)
Order Number
LH
DC
Hole Depth
DCON
PL
LF
OAL
LH
Order Number
Dimensions (mm)
Stock
TF15
4.6
5
10
Internal Coolant
Dimensions (mm)
LCF
(mm) (l/d)
TF15
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
49.1 49.1 101.1 100 1.1

79.1 82.1 134.1 133 1.1
6
6
139.1 142.1 194.1 193 1.1

199.1 202.1 254.1 253 1.1
6
6
49.1 49.1 101.1 100 1.1

79.1 82.1 134.1 133 1.1
6
6
139.1 142.1 194.1 193 1.1

199.1 202.1 254.1 253 1.1
6
6
49.1 49.1 101.1 100 1.1

79.1 82.1 134.1 133 1.1
6
6
139.1 142.1 194.1 193 1.1

199.1 202.1 254.1 253 1.1
6
6
53.1 53.1 110.1 109 1.1

86.1 89.1 142.1 141 1.1
7
7
151.1 154.1 207.1 206 1.1

216.1 219.1 272.1 271 1.1
7
7
53.1 53.1 110.1 109 1.1

86.1 89.1 142.1 141 1.1
7
7
151.1 154.1 207.1 206 1.1

216.1 219.1 272.1 271 1.1
7
7
53.1 53.1 110.1 109 1.1

86.1 89.1 142.1 141 1.1
7
7
151.1 154.1 207.1 206 1.1

216.1 219.1 272.1 271 1.1
7
7
53.2 53.2 110.2 109 1.2

86.2 89.2 142.2 141 1.2
7
7
151.2 154.2 207.2 206 1.2

216.2 219.2 272.2 271 1.2
7
7
53.2 53.2 110.2 109 1.2

86.2 89.2 142.2 141 1.2
7
7
151.2 154.2 207.2 206 1.2

216.2 219.2 272.2 271 1.2
7
7
57.2 57.2 110.2 109 1.2

92.2 95.2 148.2 147 1.2
7
7
162.2 165.2 218.2 217 1.2

232.2 235.2 288.2 287 1.2
7
7
57.2 57.2 110.2 109 1.2

92.2 95.2 148.2 147 1.2
7
7
162.2 165.2 218.2 217 1.2

232.2 235.2 288.2 287 1.2
7
7
57.2 57.2 110.2 109 1.2

92.2 95.2 148.2 147 1.2
7
7
162.2 165.2 218.2 217 1.2

232.2 235.2 288.2 287 1.2
7
7
57.3 57.3 110.3 109 1.3

92.3 95.3 148.3 147 1.3
7
7
162.3 165.3 218.3 217 1.3

232.3 235.3 288.3 287 1.3
7
7
CARBIDE
7.4
7.5
7.6
7.7
7.8
7.9
8.0
8.1
5
10
a
a
r
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
a
a
r
r
r
a
r
r
r
a
r
r
r
a
r
r
r
a
r
20
30
5
10
20
30
5
10
a
a
r
20
30
5
10
20
30
5
10
20
30
a
a
r
r
r
7
7
162.3 165.3 218.3 217 1.3

232.3 235.3 288.3 287 1.3
7
7
61.3 65.3 119.3 118 1.3

99.3 102.3 156.3 155 1.3
8
8
174.3 177.3 231.3 230 1.3

249.3 252.3 306.3 305 1.3
8
8
61.3 65.3 119.3 118 1.3

99.3 102.3 156.3 155 1.3
8
8
174.3 177.3 231.3 230 1.3

249.3 252.3 306.3 305 1.3
8
8
61.3 65.3 119.3 118 1.3

99.3 102.3 156.3 155 1.3
8
8
174.3 177.3 231.3 230 1.3

249.3 252.3 306.3 305 1.3
8
8
61.3 65.3 119.3 118 1.3

99.3 102.3 156.3 155 1.3
8
8
174.3 177.3 231.3 230 1.3

249.3 252.3 306.3 305 1.3
8
8
61.4 65.4 119.4 118 1.4

99.4 102.4 156.4 155 1.4
8
8
174.4 177.4 231.4 230 1.4

249.4 252.4 306.4 305 1.4
8
8
65.4 65.4 119.4 118 1.4

105.4 108.4 162.4 161 1.4
8
8
185.4 188.4 242.4 241 1.4

265.4 268.4 322.4 321 1.4
8
8
65.4 65.4 119.4 118 1.4

105.4 108.4 162.4 161 1.4
8
8
185.4 188.4 242.4 241 1.4

265.4 268.4 322.4 321 1.4
8
8
65.4 65.4 119.4 118 1.4

105.4 108.4 162.4 161 1.4
8
8
185.4 188.4 242.4 241 1.4

265.4 268.4 322.4 321 1.4
8
8
65.4 65.4 119.4 118 1.4

105.4 108.4 162.4 161 1.4
8
8
185.4 188.4 242.4 241 1.4

265.4 268.4 322.4 321 1.4
8
8
65.5 65.5 119.5 118 1.5

105.5 108.5 162.5 161 1.5
8
8
185.5 188.5 242.5 241 1.5

265.5 268.5 322.5 321 1.5
8
8
69.5 73.5 128.5 127 1.5

112.5 115.5 170.5 169 1.5
9
9
197.5 200.5 255.5 254 1.5

282.5 285.5 340.5 339 1.5
9
9
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
9.0
9.1
9.2
9.3
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
r
r
a
r
r
r
a
r
r
r
a
r
r
r
a
r
r
r
a
r
r
r
a
r
r
r
a
r
20
30
5
10
20
30
5
10
20
30
5
10
20
30
5
10
20
30
a
a
r
r
r
a
r
r
r
a
r
r
r
MNS0820LB
MNS0820X10DB
MNS0820X20DB
MNS0820X30DB
MNS0830LB
MNS0830X10DB
MNS0830X20DB
MNS0830X30DB
MNS0840LB
MNS0840X10DB
MNS0840X20DB
MNS0840X30DB
MNS0850LB
MNS0850X10DB
MNS0850X20DB
MNS0850X30DB
MNS0860LB
MNS0860X10DB
MNS0860X20DB
MNS0860X30DB
MNS0870LB
MNS0870X10DB
MNS0870X20DB
MNS0870X30DB
MNS0880LB
MNS0880X10DB
MNS0880X20DB
MNS0880X30DB
MNS0890LB
MNS0890X10DB
MNS0890X20DB
MNS0890X30DB
MNS0900LB
MNS0900X10DB
MNS0900X20DB
MNS0900X30DB
MNS0910LB
MNS0910X10DB
MNS0910X20DB
MNS0910X30DB
MNS0920LB
MNS0920X10DB
MNS0920X20DB
MNS0920X30DB
MNS0930LB
MNS0930X10DB
MNS0930X20DB
MNS0930X30DB
69.5 73.5 128.5 127 1.5

112.5 115.5 170.5 169 1.5
9
9
197.5 200.5 255.5 254 1.5

282.5 285.5 340.5 339 1.5
9
9
69.5 73.5 128.5 127 1.5

112.5 115.5 170.5 169 1.5
9
9
197.5 200.5 255.5 254 1.5

282.5 285.5 340.5 339 1.5
9
9
69.5 73.5 128.5 127 1.5

112.5 115.5 170.5 169 1.5
9
9
197.5 200.5 255.5 254 1.5

282.5 285.5 340.5 339 1.5
9
9
69.5 73.5 128.5 127 1.5

112.5 115.5 170.5 169 1.5
9
9
197.5 200.5 255.5 254 1.5

282.5 285.5 340.5 339 1.5
9
9
73.6 73.6 128.6 127 1.6

118.6 121.6 176.6 175 1.6
9
9
208.6 211.6 266.6 265 1.6

298.6 301.6 356.6 355 1.6
9
9
73.6 73.6 128.6 127 1.6

118.6 121.6 176.6 175 1.6
9
9
208.6 211.6 266.6 265 1.6

298.6 301.6 356.6 355 1.6
9
9
73.6 73.6 128.6 127 1.6

118.6 121.6 176.6 175 1.6
9
9
208.6 211.6 266.6 265 1.6

298.6 301.6 356.6 355 1.6
9
9
73.6 73.6 128.6 127 1.6

118.6 121.6 176.6 175 1.6
9
9
208.6 211.6 266.6 265 1.6

298.6 301.6 356.6 355 1.6
9
9
73.6 73.6 128.6 127 1.6

118.6 121.6 176.6 175 1.6
9
9
208.6 211.6 266.6 265 1.6

298.6 301.6 356.6 355 1.6
9
9
77.7 81.7 137.7 136 1.7

125.7 128.7 183.7 182 1.7
10
10
220.7 223.7 278.7 277 1.7

315.7 318.7 373.7 372 1.7
10
10
77.7 81.7 137.7 136 1.7

125.7 128.7 183.7 182 1.7
10
10
220.7 223.7 278.7 277 1.7

315.7 318.7 373.7 372 1.7
10
10
77.7 81.7 137.7 136 1.7

125.7 128.7 183.7 182 1.7
10
10
220.7 223.7 278.7 277 1.7

315.7 318.7 373.7 372 1.7
10
10
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
LF
OAL
5
10
LH
(mm) (l/d)
LCF
Hole Depth
DCON
PL
LF
OAL
LH
57.3 57.3 110.3 109 1.3

92.3 95.3 148.3 147 1.3
N082
N083
Q001
DRILLING
7.3
20
30
MNS0700LB
MNS0700X10DB
MNS0700X20DB
MNS0700X30DB
MNS0710LB
MNS0710X10DB
MNS0710X20DB
MNS0710X30DB
MNS0720LB
MNS0720X10DB
MNS0720X20DB
MNS0720X30DB
MNS0730LB
MNS0730X10DB
MNS0730X20DB
MNS0730X30DB
MNS0740LB
MNS0740X10DB
MNS0740X20DB
MNS0740X30DB
MNS0750LB
MNS0750X10DB
MNS0750X20DB
MNS0750X30DB
MNS0760LB
MNS0760X10DB
MNS0760X20DB
MNS0760X30DB
MNS0770LB
MNS0770X10DB
MNS0770X20DB
MNS0770X30DB
MNS0780LB
MNS0780X10DB
MNS0780X20DB
MNS0780X30DB
MNS0790LB
MNS0790X10DB
MNS0790X20DB
MNS0790X30DB
MNS0800LB
MNS0800X10DB
MNS0800X20DB
MNS0800X30DB
MNS0810LB
MNS0810X10DB
MNS0810X20DB
MNS0810X30DB
Order Number
DCON
7.2
DC
PL
7.1
5
10
Order Number
Dimensions (mm)
Stock
TF15
7.0
Internal Coolant
Dimensions (mm)
LCF
(mm) (l/d)
TF15
DC
Hole Depth
Internal Coolant
Stock
N079
MNS
WSTAR DRILLS
9.5
9.6
9.7
9.8
9.9
20
30
5
10
20
30
5
10
r
r
r
a
r
20
30
5
10
20
30
5
10
20
30
5
10
a
a
r
r
5
10
20
30
5
10.1 10
20
5
10.2 10
20
5
10.3 10
20
5
10.4 10
20
r
r
a
r
r
a
r
r
a
r
r
5
10.5 10
20
5
10.6 10
20
5
10.7 10
20
a
a
r
r
a
r
r
MNS0940LB
MNS0940X10DB
MNS0940X20DB
MNS0940X30DB
MNS0950LB
MNS0950X10DB
MNS0950X20DB
MNS0950X30DB
MNS0960LB
MNS0960X10DB
MNS0960X20DB
MNS0960X30DB
MNS0970LB
MNS0970X10DB
MNS0970X20DB
MNS0970X30DB
MNS0980LB
MNS0980X10DB
MNS0980X20DB
MNS0980X30DB
MNS0990LB
MNS0990X10DB
MNS0990X20DB
MNS0990X30DB
MNS1000LB
MNS1000X10DB
MNS1000X20DB
MNS1000X30DB
MNS1010LB
MNS1010X10DB
MNS1010X20DB
MNS1020LB
MNS1020X10DB
MNS1020X20DB
MNS1030LB
MNS1030X10DB
MNS1030X20DB
MNS1040LB
MNS1040X10DB
MNS1040X20DB
MNS1050LB
MNS1050X10DB
MNS1050X20DB
MNS1060LB
MNS1060X10DB
MNS1060X20DB
MNS1070LB
MNS1070X10DB
MNS1070X20DB
10.8 10
10
10
20
77.7 81.7 137.7 136 1.7

125.7 128.7 183.7 182 1.7
10
10
10.9 10
20
220.7 223.7 278.7 277 1.7

315.7 318.7 373.7 372 1.7
10
10
81.7 81.7 137.7 136 1.7

131.7 134.7 189.7 188 1.7
10
10
5
11.0 10
20
231.7 234.7 289.7 288 1.7

331.7 334.7 389.7 388 1.7
10
10
81.8 81.8 137.8 136 1.8

131.8 134.8 189.8 188 1.8
10
10
231.8 234.8 289.8 288 1.8

331.8 334.8 389.8 388 1.8
10
10
81.8 81.8 137.8 136 1.8

131.8 134.8 189.8 188 1.8
5
11.1 10
20
a
a
a
r
r
5
11.2 10
20
10
10
5
11.3 10
20
231.8 234.8 289.8 288 1.8

331.8 334.8 389.8 388 1.8
10
10
11.4 10
81.8 81.8 137.8 136 1.8

131.8 134.8 189.8 188 1.8
10
10
20
231.8 234.8 289.8 288 1.8

331.8 334.8 389.8 388 1.8
10
10
5
11.5 10
20
81.8 81.8 137.8 136 1.8

131.8 134.8 189.8 188 1.8
10
10
11.6 10
231.8 234.8 289.8 288 1.8

331.8 334.8 389.8 388 1.8
10
10
20
85.8 89.8 150.8 149 1.8

138.8 141.8 202.8 201 1.8
243.8 246.8 307.8 306 1.8
11
11
11
5
11.7 10
20
85.9 89.9 150.9 149 1.9

138.9 141.9 202.9 201 1.9
243.9 246.9 307.9 306 1.9
11
11
11
85.9 89.9 150.9 149 1.9

138.9 141.9 202.9 201 1.9
243.9 246.9 307.9 306 1.9
11
11
11
85.9 89.9 150.9 149 1.9

138.9 141.9 202.9 201 1.9
243.9 246.9 307.9 306 1.9
11
11
11
85.9 89.9 150.9 149 1.9

138.9 141.9 202.9 201 1.9
243.9 246.9 307.9 306 1.9
11
11
11
89.9 89.9 150.9 149 1.9

144.9 147.9 208.9 207 1.9
254.9 257.9 318.9 317 1.9
11
11
11
89.9 89.9 150.9 149 1.9

144.9 147.9 208.9 207 1.9
254.9 257.9 318.9 317 1.9
11
11
11
r
a
11.8 10
20
5
11.9 10
20
5
12.0 10
20
5
12.1 10
20
a
r
5
12.2 10
20
a
a
r
a
12.3 10
20
MNS1080LB
MNS1080X10DB
MNS1080X20DB
MNS1090LB
MNS1090X10DB
MNS1090X20DB
MNS1100LB
MNS1100X10DB
MNS1100X20DB
MNS1110LB
MNS1110X10DB
MNS1110X20DB
MNS1120LB
MNS1120X10DB
MNS1120X20DB
MNS1130LB
MNS1130X10DB
MNS1130X20DB
MNS1140LB
MNS1140X10DB
MNS1140X20DB
MNS1150LB
MNS1150X10DB
MNS1150X20DB
MNS1160LB
MNS1160X10DB
MNS1160X20DB
MNS1170LB
MNS1170X10DB
MNS1170X20DB
MNS1180LB
MNS1180X10DB
MNS1180X20DB
MNS1190LB
MNS1190X10DB
MNS1190X20DB
MNS1200LB
MNS1200X10DB
MNS1200X20DB
MNS1210LB
MNS1210X10DB
MNS1210X20DB
MNS1220LB
MNS1220X10DB
MNS1220X20DB
MNS1230LB
MNS1230X10DB
MNS1230X20DB
N080
DCON
PL
LF
OAL
Order Number
LH
(mm) (l/d)
Dimensions (mm)
Stock
TF15
DC
Hole Depth
220.7 223.7 278.7 277 1.7

315.7 318.7 373.7 372 1.7
LF
10
10
OAL
77.7 81.7 137.7 136 1.7

125.7 128.7 183.7 182 1.7
LH
DCON
20
30
10.0
DRILLING
Order Number
PL
9.4
5
10
Internal Coolant
Dimensions (mm)
LCF
(mm) (l/d)
TF15
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
90.0 90.0 151.0 149 2.0
11
145.0 148.0 209.0 207 2.0

255.0 258.0 319.0 317 2.0
11
11
90.0 90.0 151.0 149 2.0

145.0 148.0 209.0 207 2.0
255.0 258.0 319.0 317 2.0
11
11
11
90.0 90.0 151.0 149 2.0

145.0 148.0 209.0 207 2.0
255.0 258.0 319.0 317 2.0
11
11
11
94.0 98.0 160.0 158 2.0

152.0 155.0 217.0 215 2.0
267.0 270.0 332.0 330 2.0
12
12
12
94.0 98.0 160.0 158 2.0

152.0 155.0 217.0 215 2.0
267.0 270.0 332.0 330 2.0
12
12
12
94.1 98.1 160.1 158 2.1

152.1 155.1 217.1 215 2.1
267.1 270.1 332.1 330 2.1
12
12
12
94.1 98.1 160.1 158 2.1

152.1 155.1 217.1 215 2.1
267.1 270.1 332.1 330 2.1
12
12
12
94.1 98.1 160.1 158 2.1

152.1 155.1 217.1 215 2.1
267.1 270.1 332.1 330 2.1
12
12
12
98.1 98.1 160.1 158 2.1

158.1 161.1 223.1 221 2.1
278.1 281.1 343.1 341 2.1
12
12
12
98.1 98.1 160.1 158 2.1

158.1 161.1 223.1 221 2.1
278.1 281.1 343.1 341 2.1
12
12
12
98.1 98.1 160.1 158 2.1

158.1 161.1 223.1 221 2.1
278.1 281.1 343.1 341 2.1
12
12
12
98.2 98.2 160.2 158 2.2

158.2 161.2 223.2 221 2.2
278.2 281.2 343.2 341 2.2
12
12
12
98.2 98.2 160.2 158 2.2

158.2 161.2 223.2 221 2.2
278.2 281.2 343.2 341 2.2
12
12
12
102.2 106.2 169.2 167 2.2

165.2 168.2 231.2 229 2.2
290.2 293.2 356.2 354 2.2
13
13
13
102.2 106.2 169.2 167 2.2

165.2 168.2 231.2 229 2.2
290.2 293.2 356.2 354 2.2
13
13
13
102.2 106.2 169.2 167 2.2

165.2 168.2 231.2 229 2.2
290.2 293.2 356.2 354 2.2
13
13
13
CARBIDE
12.5 10
20
5
10
12.6
20
12.7 10
20
5
12.8 10
20
5
12.9 10
20
5
13.1 10
20
r
a
r
a
a
a
a
r
r
13.2 10
20
5
13.3 10
20
13.4 10
20
5
13.5 10
20
5
13.6 10
20
r
a
5
13.7 10
20
5
13.8 10
20
r
a
13.9 10
20
5
14.0 10
20
a
a
a
13
13
13
106.3 106.3 169.3 167 2.3

171.3 174.3 237.3 235 2.3
301.3 304.3 367.3 365 2.3
13
13
13
106.3 106.3 169.3 167 2.3

171.3 174.3 237.3 235 2.3
301.3 304.3 367.3 365 2.3
13
13
13
106.3 106.3 169.3 167 2.3

171.3 174.3 237.3 235 2.3
301.3 304.3 367.3 365 2.3
13
13
13
106.3 106.3 169.3 167 2.3

171.3 174.3 237.3 235 2.3
301.3 304.3 367.3 365 2.3
13
13
13
106.4 106.4 169.4 167 2.4

171.4 174.4 237.4 235 2.4
301.4 304.4 367.4 365 2.4
13
13
13
110.4 114.4 178.4 176 2.4

178.4 181.4 245.4 243 2.4
313.4 316.4 380.4 378 2.4
14
14
14
110.4 114.4 178.4 176 2.4

178.4 181.4 245.4 243 2.4
313.4 316.4 380.4 378 2.4
14
14
14
110.4 114.4 178.4 176 2.4

178.4 181.4 245.4 243 2.4
313.4 316.4 380.4 378 2.4
14
14
14
110.4 114.4 178.4 176 2.4

178.4 181.4 245.4 243 2.4
313.4 316.4 380.4 378 2.4
14
14
14
110.5 114.5 178.5 176 2.5

178.5 181.5 245.5 243 2.5
313.5 316.5 380.5 378 2.5
14
14
14
114.5 114.5 178.5 176 2.5

184.5 187.5 251.5 249 2.5
324.5 327.5 391.5 389 2.5
14
14
14
114.5 114.5 178.5 176 2.5

184.5 187.5 251.5 249 2.5
324.5 327.5 391.5 389 2.5
14
14
14
114.5 114.5 178.5 176 2.5

184.5 187.5 251.5 249 2.5
324.5 327.5 391.5 389 2.5
14
14
14
114.5 114.5 178.5 176 2.5

184.5 187.5 251.5 249 2.5
324.5 327.5 391.5 389 2.5
14
14
14
114.5 114.5 178.5 176 2.5

184.5 187.5 251.5 249 2.5
324.5 327.5 391.5 389 2.5
14
14
14
LF
102.3 106.3 169.3 167 2.3

165.3 168.3 231.3 229 2.3
290.3 293.3 356.3 354 2.3
OAL
13
13
13
LH
102.3 106.3 169.3 167 2.3

165.3 168.3 231.3 229 2.3
290.3 293.3 356.3 354 2.3
DRILLING
20
MNS1240LB
MNS1240X10DB
MNS1240X20DB
MNS1250LB
MNS1250X10DB
MNS1250X20DB
MNS1260LB
MNS1260X10DB
MNS1260X20DB
MNS1270LB
MNS1270X10DB
MNS1270X20DB
MNS1280LB
MNS1280X10DB
MNS1280X20DB
MNS1290LB
MNS1290X10DB
MNS1290X20DB
MNS1300LB
MNS1300X10DB
MNS1300X20DB
MNS1310LB
MNS1310X10DB
MNS1310X20DB
MNS1320LB
MNS1320X10DB
MNS1320X20DB
MNS1330LB
MNS1330X10DB
MNS1330X20DB
MNS1340LB
MNS1340X10DB
MNS1340X20DB
MNS1350LB
MNS1350X10DB
MNS1350X20DB
MNS1360LB
MNS1360X10DB
MNS1360X20DB
MNS1370LB
MNS1370X10DB
MNS1370X20DB
MNS1380LB
MNS1380X10DB
MNS1380X20DB
MNS1390LB
MNS1390X10DB
MNS1390X20DB
MNS1400LB
MNS1400X10DB
MNS1400X20DB
DCON
a
r
Order Number
PL
12.4 10
5
13.0 10
20
Dimensions (mm)
LCF
(mm) (l/d)
TF15
DC
Hole Depth
Internal Coolant
Stock
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N082
N083
Q001
N081

CARBIDE
MNS
WSTAR DRILLS
y LB Type Drill
Work
material
Aluminium Alloy (5% < Si < 10%)
Aluminium Alloy (Si>10%)
ASTM 333.0 etc
ASTM 383.0, ASTM A390.0 etc
Dia.
DC
(mm)
Revolution
(min-1)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
14.0
11900
9500
7600
7500
5900
4700
5300
4500
Feed rate
(Min.Max.)
(mm/rev)
0.1
0.15
0.2
0.25
0.3
0.4
0.5
0.5
(0.11 0.16)
(0.13 0.20)
(0.17 0.25)
(0.21 0.32)
(0.27 0.40)
(0.33 0.50)
(0.40 0.60)
(0.40 0.60)
Feed rate
(Min.Max.)
(mm/rev)
Revolution
(min-1)
11900
9500
7600
7500
5900
4700
5300
4500
0.15
0.2
0.25
0.35
0.45
0.55
0.7
0.7
(0.16 0.21)
(0.20 0.27)
(0.25 0.33)
(0.32 0.42)
(0.40 0.53)
(0.50 0.67)
(0.60 0.80)
(0.60 0.80)
Feed rate
(Min.Max.)
(mm/rev)
Revolution
(min-1)
11900
9500
7600
7500
5900
4700
5300
4500
(0.16 0.21)
(0.20 0.27)
(0.25 0.33)
(0.32 0.42)
(0.40 0.53)
(0.50 0.67)
(0.60 0.80)
(0.60 0.80)
0.15
0.2
0.25
0.35
0.45
0.55
0.7
0.7
(Note 1) When using the drill with a length over l/d 10, it is necessary to use a prep holes as a guide. (If no prep-hole is used then drill
breakage can occur)
(Note 2) For pilot hole drilling, Mitsubishi Materials MNS-LB, MAE-MB or MAS-MB drill is recommended.
y DB Type Drill
Work
material
Aluminium Alloy (5% < Si < 10%)
Aluminium Alloy (Si>10%)
ASTM 333.0 etc
ASTM 383.0, ASTM A390.0 etc
Dia.
DC
(mm)
Revolution
(min-1)
3.2
4.0
5.0
6.3
8.0
10.0
12.0
14.0
8900
7100
5700
6000
4700
3800
4200
3600
Feed rate
(Min.Max.)
(mm/rev)
0.1
0.15
0.2
0.25
0.3
0.4
0.5
0.5
(0.11 0.16)
(0.13 0.20)
(0.17 0.25)
(0.21 0.32)
(0.27 0.40)
(0.33 0.50)
(0.40 0.60)
(0.40 0.60)
Feed rate
(Min.Max.)
(mm/rev)
Revolution
(min-1)
8900
7100
5700
6000
4700
3800
4200
3600
0.15
0.2
0.25
0.35
0.45
0.55
0.7
0.7
(0.16 0.21)
(0.20 0.27)
(0.25 0.33)
(0.32 0.42)
(0.40 0.53)
(0.50 0.67)
(0.60 0.80)
(0.60 0.80)
Feed rate
(Min.Max.)
(mm/rev)
Revolution
(min-1)
8900
7100
5700
6000
4700
3800
4200
3600
0.15
0.2
0.25
0.35
0.45
0.55
0.7
0.7
(0.16 0.21)
(0.20 0.27)
(0.25 0.33)
(0.32 0.42)
(0.40 0.53)
(0.50 0.67)
(0.60 0.80)
(0.60 0.80)
DRILLING
(Note 1) When using the drill with a length over l/d 10, it is necessary to use a prep holes as a guide. (If no prep-hole is used then drill
breakage can occur)
(Note 2) For pilot hole drilling, Mitsubishi Materials MNS-LB, MAE-MB or MAS-MB drill is recommended.
N082
CARBIDE
Drill Length
Drill Installation
A > DC x 1.5
Run-out < 0.03mm
Coolant Handling
Thin Workpiece
Interrupted Cutting
Adjusting Screw
Drill Holding

Through Coolant Type

Spindles
Through
Coolant Type
Revolving
Coolant
Machine Type
DC

coolant exchange is
recommended.
One Process
If Bending
Occurs
Support
the Workpiece
zSpot face with

an end mill
prior to drilling.

cutting.
xAdd a 45chamfer.
DRILLING

when drilling
the interrupted
part.
Requires Prior
Machining

0.5MPa7MPa
Stepped Holes
zLower the feed
TECHNICAL DATA
Q001
N083

CARBIDE
MNS
WSTAR DRILLS
y OPERATIONAL GUIDANCE FOR MNS...DB DRILLS

Mitsubishi type MNS-LB, MAE-MB or MAS-MB drill is recommended.

zPenetrate the guide hole at low revolution. (Cutting speed

2030m/min, feed rate 0.20.3mm/rev)
xStop the long type drill 1 3mm short of the guide hole bottom.
zAfter drilling, lower the cutting revolution about 1 2mm short of the
hole end. (Cutting speed of around 20 30m/min)
3000mm/min.
cFinally, clear the hole at a cutting speed of 20 30m/min and feed rate
of 0.20.3mm/rev.

y 1. Spot facing
DRILLING
zPenetrate the guide hole at a low revolution. (Cutting speed

20 30m/min, feed rate 0.2 0.3mm/rev)

xA feed rate of 0.05 0.1mm/rev is recommended.
N084
Mitsubishi type MNS-LB, MAE-MB or MAS-MB drill is recommended.

zFinally clear the hole at a cutting speed of 20 30m/min and feed rate of
0.2 0.3mm/rev.
3000mm/min.
SOLID CARBIDE DRILLS FOR DIE & MOULD MACHINING
MHS
WSTAR DRILLS
Stainless Steel
DC < 3 3<DC < 6 6<DC < 10 10<DC < 12
h6
+0.010
0.002
0
0.006
+0.010
0.005
0
0.009
LF
140
DC
PL
+0.010
0.002
0
0.008
LCF
LH
PL
135
DC
LCF
LH
OAL
LF
142
DC
LCF
LH
Type3
DCON(h6)
LCF
LH
Type2
OAL
LF
140
DC
PL
Type1
OAL
LF
PL
+0.010
0.008
0
0.011
DCON(h6)
Steel
DCON(h6)
CARBIDE
DCON(h6)
aHigh backling strength and unique double margin.

aNon-step drilling with long tool life for high hardness steel,35HRC-55HRC
Type4
OAL
(Note 1) MHS drills are suitable for use with shrink fit holders.
(Note 2) Use the shortest type in the respective diameter as a pilot drill.
2
5
1.20 10
18
26
2
5
1.30 12
20
30
6.2 9.9 60.2

9.2 12.9 60.2
60 0.2
60 0.2
3
3
1
2
3
6
15.2 18.9 60.2
60 0.2
1.45 11
25.2 28.9 60.2

35.2 38.9 80.2
60 0.2
80 0.2
3
3
2
2
21
30
6.2 9.7 60.2

9.2 12.7 60.2
60 0.2
60 0.2
3
3
1
2
2
6
15.2 18.7 60.2
60 0.2
1.50 10
25.2 28.7 60.2

35.2 38.7 80.2
60 0.2
80 0.2
3
3
2
2
20
30
6.2 9.6 60.2

9.2 12.6 60.2
60 0.2
60 0.2
3
3
1
2
2
5
15.2 18.6 60.2
60 0.2
1.60 10
25.2 28.6 60.2

35.2 38.6 80.2
60 0.2
80 0.2
3
3
2
2
19
30
7.2 10.4 60.2

11.3 14.5 60.3
60 0.2
60 0.3
3
3
1
2
2
5
20.3 23.5 60.3
60 0.3
1.70 9
30.3 33.5 80.3

45.3 48.5 80.3
80 0.3
80 0.3
3
3
2
2
18
29
Type
7.3 10.3
60.3 60 0.3
11.3 14.3
60.3 60 0.3
20.3 23.3
60.3 60 0.3
30.3 33.3
45.3 48.3
80.3 80 0.3
80.3 80 0.3
3
3
2
2
8.3 11.2
13.3 16.2
60.3 60 0.3
60.3 60 0.3
3
3
1
2
20.3 23.2
60.3 60 0.3
35.3 38.2 80.3 80 0.3

55.3 58.2 100.3 100 0.3
3
3
2
2
8.3 11.1
13.3 16.1
60.3 60 0.3
60.3 60 0.3
3
3
1
2
20.3 23.1
60.3 60 0.3
35.3 38.1 80.3 80 0.3

55.3 58.1 100.3 100 0.3
3
3
2
2
8.3 10.9
13.3 15.9
60.3 60 0.3
60.3 60 0.3
3
3
1
2
20.3 22.9
60.3 60 0.3
35.3 37.9 80.3 80 0.3

55.3 57.9 100.3 100 0.3
3
3
2
2
8.3 10.7
13.4 15.8
60.3 60 0.3
60.4 60 0.4
3
3
1
2
20.4 22.8
60.4 60 0.4
35.4 37.8 80.4 80 0.4

55.4 57.8 100.4 100 0.4
3
3
2
2
DRILLING
20
29
DCON
1.10 11
18
29
PL
1.40 11
2
2
LF
2
5
25.17 28.97 60.17 60 0.17 3

35.17 38.97 80.17 80 0.17 3
OAL
15.17 18.97 60.17 60 0.17 3
MHS0140L007B
MHS0140L011B
MHS0140L020B
MHS0140L030B
MHS0140L045B
MHS0145L008B
MHS0145L013B
MHS0145L020B
MHS0145L035B
MHS0145L055B
MHS0150L008B
MHS0150L013B
MHS0150L020B
MHS0150L035B
MHS0150L055B
MHS0160L008B
MHS0160L013B
MHS0160L020B
MHS0160L035B
MHS0160L055B
MHS0170L008B
MHS0170L013B
MHS0170L020B
MHS0170L035B
MHS0170L055B
(mm) (l/d)
LH
22
30
Type
LCF
1.00 12
VP15TF
DCON
3
6
PL
1
2
LF
23
30
Dimensions (mm)
6.17 9.97 60.17 60 0.17 3

9.17 12.97 60.17 60 0.17 3
OAL
0.95 13
MHS0095L006B
MHS0095L009B
MHS0095L015B
MHS0095L025B
MHS0095L035B
MHS0100L006B
MHS0100L009B
MHS0100L015B
MHS0100L025B
MHS0100L035B
MHS0110L006B
MHS0110L009B
MHS0110L015B
MHS0110L025B
MHS0110L035B
MHS0120L006B
MHS0120L009B
MHS0120L015B
MHS0120L025B
MHS0120L035B
MHS0130L007B
MHS0130L011B
MHS0130L020B
MHS0130L030B
MHS0130L045B
LH
Stock
Order Number
LCF
3
6
DC
Hole Depth
Dimensions (mm)
Order Number
(mm) (l/d)
Internal Coolant
Stock
VP15TF
DC
Hole Depth
Internal Coolant
CUTTING CONDITIONS
a
OPERATION GUIDANCE
TECHNICAL DATA
N093
N094
Q001
N085
MHS
WSTAR DRILLS
21
30
2
5
1.95 10
20
30
2
5
2.00 9
20
30
3
7
2.10 11
23
30
2
6
2.20 11
22
30
2
6
2.30 10
21
30
2
5
2.40 9
20
28
2
5
2.45 11
24
30
2
5
2.50 11
23
30
0.4
2
5
15.4 17.6 60.4 60

25.4 27.6 60.4 60
0.4
2.60 10
45.4 47.6 80.4 80

65.4 67.6 100.4 100
0.4
0.4
3
3
2
2
22
30
10.3 12.4 60.3 60

15.4 17.5 60.4 60
0.3
0.4
3
3
1
2
2
4
25.4 27.5 60.4 60
0.4
2.70 10
45.4 47.5 80.4 80

65.4 67.5 100.4 100
0.4
0.4
3
3
2
2
21
30
10.4 12.4 60.4 60

15.4 17.4 60.4 60
0.4
0.4
3
3
1
2
2
4
25.4 27.4 60.4 60
0.4
2.80 9
45.4 47.4 80.4 80

65.4 67.4 100.4 100
0.4
0.4
3
3
2
2
20
29
10.4 12.3 60.4 60

15.4 17.3 60.4 60
0.4
0.4
3
3
1
2
2
4
25.4 27.3 60.4 60
0.4
2.90 9
45.4 47.3 80.4 80

65.4 67.3 100.4 100
0.4
0.4
3
3
2
2
19
28
12.4 14.1 60.4 60

20.4 22.1 60.4 60
0.4
0.4
3
3
1
2
2
4
30.4 32.1 80.4 80
0.4
2.95 9
a
a
MHS0260L013B
MHS0260L020B
MHS0260L035B
MHS0260L065B
MHS0260L090B
MHS0270L013B
MHS0270L020B
MHS0270L035B
MHS0270L065B
MHS0270L090B
MHS0280L014B
MHS0280L020B
MHS0280L035B
MHS0280L065B
MHS0280L090B
MHS0290L014B
MHS0290L020B
MHS0290L035B
MHS0290L065B
MHS0290L090B
MHS0295L014B
MHS0295L020B
MHS0295L035B
MHS0295L065B
MHS0295L090B
MHS0300L020B
MHS0300L040B
MHS0300L060B
MHS0300L090B
MHS0310L020B
MHS0310L040B
MHS0310L060B
MHS0310L090B
MHS0320L020B
MHS0320L040B
MHS0320L060B
MHS0320L090B
MHS0330L020B
MHS0330L040B
MHS0330L060B
MHS0330L090B
MHS0340L020B
MHS0340L040B
MHS0340L060B
MHS0340L090B
MHS0350L020B
MHS0350L040B
MHS0350L060B
MHS0350L090B
(mm) (l/d)
55.4 57.1 100.4 100

75.4 77.1 120.4 120
0.4
0.4
3
3
2
2
19
28
12.4 13.9 60.4 60

20.5 22.0 60.5 60
0.4
0.5
3
3
1
2
4
10
30.5 32.0 80.5 80
0.5
55.5 57.0 100.5 100

75.5 77.0 120.5 120
0.5
0.5
3
3
2
2
17
27
12.4 13.7 60.4 60

20.5 21.8 60.5 60
0.4
0.5
3
3
1
2
4
10
0.5
17
26
30.5 31.8 80.5 80

55.5 56.8 100.5 100
75.5 76.8 120.5 120
0.5
0.5
3
3
2
2
4
10
12.4 13.5 60.4 60

20.5 21.6 60.5 60
0.4
0.5
3
3
1
2
16
25
3
9
16
25
3
9
15
24
3
9
14
23
30.5 31.6 80.5 80
0.5
55.5 56.6 100.5 100

75.5 76.6 120.5 120
0.5
0.5
3
3
2
2
13.4 14.4 70.4 70

20.5 21.5 70.5 70
0.4
0.5
4
4
1
2
35.5 36.5 90.5 90
0.5
65.5 66.5 110.5 110

90.5 91.5 140.5 140
0.5
0.5
4
4
2
2
13.5 16.3 70.5 70

20.5 23.3 70.5 70
0.5
0.5
4
4
1
2
35.5 38.3 90.5 90
0.5
65.5 68.3 110.5 110

90.5 93.3 140.5 140
0.5
0.5
4
4
2
2
3.0
3.1
3.2
3.3
3.4
3.5
N086
DCON
1.90 10
PL
LF
2
5
0.3
OAL
10.3 12.5 60.3 60
Type
13.5 16.1 70.5

20.5 23.1 70.5
70
70
0.5
0.5
4
4
1
2
35.5 38.1 90.5
LH
22
30
VP15TF
Hole Depth
1.80 11
DCON
PL
MHS0180L010B
MHS0180L015B
MHS0180L025B
MHS0180L045B
MHS0180L065B
MHS0190L010B
MHS0190L015B
MHS0190L025B
MHS0190L045B
MHS0190L065B
MHS0195L010B
MHS0195L015B
MHS0195L025B
MHS0195L045B
MHS0195L065B
MHS0200L010B
MHS0200L015B
MHS0200L025B
MHS0200L045B
MHS0200L065B
MHS0210L012B
MHS0210L020B
MHS0210L030B
MHS0210L055B
MHS0210L075B
MHS0220L012B
MHS0220L020B
MHS0220L030B
MHS0220L055B
MHS0220L075B
MHS0230L012B
MHS0230L020B
MHS0230L030B
MHS0230L055B
MHS0230L075B
MHS0240L012B
MHS0240L020B
MHS0240L030B
MHS0240L055B
MHS0240L075B
MHS0245L013B
MHS0245L020B
MHS0245L035B
MHS0245L065B
MHS0245L090B
MHS0250L013B
MHS0250L020B
MHS0250L035B
MHS0250L065B
MHS0250L090B
LF
OAL
Dimensions (mm)
Order Number
LH
(mm) (l/d)
DC
Stock
Type
LCF
Order Number
DRILLING
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
90
0.5
65.5 68.1 110.5 110

90.5 93.1 140.5 140
0.5
0.5
4
4
2
2
13.5 15.9 70.5

20.6 23.0 70.6
70
70
0.5
0.6
4
4
1
2
35.6 38.0 90.6
90
0.6
65.6 68.0 110.6 110

90.6 93.0 140.6 140
0.6
0.6
4
4
2
2
14.5 16.7 70.5

20.6 22.8 70.6
70
70
0.5
0.6
4
4
1
2
35.6 37.8 90.6
90
0.6
65.6 67.8 110.6 110

90.6 92.8 140.6 140
0.6
0.6
4
4
2
2
14.5 16.6 70.5

20.6 22.7 70.6
70
70
0.5
0.6
4
4
1
2
35.6 37.7 90.6
90
0.6
65.6 67.7 110.6 110

90.6 92.7 140.6 140
0.6
0.6
4
4
2
2
14.5 16.5 70.5

20.6 22.6 70.6
70
70
0.5
0.6
4
4
1
2
35.6 37.6 90.6
90
0.6
65.6 67.6 110.6 110

90.6 92.6 140.6 140
0.6
0.6
4
4
2
2
19.5 20.5 70.5

39.5 40.5 90.5
70
90
0.5
0.5
4
4
3
4
59.5 60.5 110.5 110

89.5 90.5 140.5 140
0.5
0.5
4
4
4
4
20.0 20.5 70.5

40.1 40.6 90.6
70
90
0.5
0.6
4
4
3
4
60.1 60.6 110.6 110

90.1 90.6 140.6 140
0.6
0.6
4
4
4
4
20.1 20.6 70.6

40.1 40.6 90.6
70
90
0.6
0.6
4
4
3
4
60.1 60.6 110.6 110

90.1 90.6 140.6 140
0.6
0.6
4
4
4
4
20.1 20.6 70.6

40.1 40.6 90.6
70
90
0.6
0.6
4
4
3
4
60.1 60.6 110.6 110

90.1 90.6 140.6 140
0.6
0.6
4
4
4
4
20.1 20.6 70.6

40.1 40.6 90.6
70
90
0.6
0.6
4
4
3
4
60.1 60.6 110.6 110

90.1 90.6 140.6 140
0.6
0.6
4
4
4
4
20.1 20.6 70.6

40.1 40.6 90.6
70
90
0.6
0.6
4
4
3
4
60.1 60.6 110.6 110

90.1 90.6 140.6 140
0.6
0.6
4
4
4
4
CARBIDE
3
8
3.8 13
21
29
3
8
3.9 13
21
28
2
7
4.0 12
20
27
2
7
4.1 12
19
26
2
7
4.2 11
19
26
2
6
4.3 11
18
25
2
6
4.4 11
18
24
2
6
4.5 10
17
24
2
6
10
16
3
4
23
29
90.7 90.7 140.7 140 0.7

120.7 120.7 170.7 170 0.7
4
4
4
4
1
6
10
20.7 20.7 70.7 70 0.7

40.7 40.7 90.7 90 0.7
4
4
3
4
16
22
29
60.7 60.7 110.7 110 0.7

90.7 90.7 140.7 140 0.7
120.7 120.7 170.7 170 0.7
4
4
4
4
1
5
20.7 20.7 70.7 70 0.7

40.7 40.7 90.7 90 0.7
4
4
3
4
10
16
60.7 60.7 110.7 110 0.7
90.7 90.7 140.7 140 0.7

120.7 120.7 170.7 170 0.7
4
4
4
4
22
28
6
6
3
4
1
5
19.2 20.7 70.7 70 0.7

39.2 40.7 90.7 90 0.7
59.2 60.7 110.7 110 0.7
89.2 90.7 140.7 140 0.7

119.2 120.7 170.7 170 0.7
6
6
19.2 20.7 70.7 70 0.7

39.3 40.8 90.8 90 0.8
6
6
90.7 90.7 140.7 140 0.7

120.7 120.7 170.7 170 0.7
4
4
4
4
20.6 20.6 70.6 70 0.6

40.7 40.7 90.7 90 0.7
4
4
3
4
60.7 60.7 110.7 110 0.7
90.7 90.7 140.7 140 0.7

120.7 120.7 170.7 170 0.7
4
4
4
4
20.7 20.7 70.7 70 0.7

40.7 40.7 90.7 90 0.7
4
4
60.7 60.7 110.7 110 0.7
4.6
4.7
4.8
4.9
15
4
4
21
27
3
4
3
9
5.0
59.3 60.8 110.8 110 0.8
5.1 15
89.3 90.8 140.8 140 0.8

119.3 120.8 170.8 170 0.8
6
6
4
4
21
27
19.2 20.7 70.7 70 0.7

39.3 40.8 90.8 90 0.8
6
6
3
4
3
9
59.3 60.8 110.8 110 0.8
5.2 15
89.3 90.8 140.8 140 0.8

119.3 120.8 170.8 170 0.8
6
6
4
4
20
26
19.3 20.8 70.8 70 0.8

39.3 40.8 90.8 90 0.8
6
6
3
4
3
9
59.3 60.8 110.8 110 0.8
5.3 14
89.3 90.8 140.8 140 0.8

119.3 120.8 170.8 170 0.8
6
6
4
4
20
26
19.3 20.8 70.8 70 0.8

39.3 40.8 90.8 90 0.8
6
6
3
4
3
9
59.3 60.8 110.8 110 0.8
5.4 14
89.3 90.8 140.8 140 0.8

119.3 120.8 170.8 170 0.8
6
6
4
4
20
25
r
r
19.8 20.8 70.8 70 0.8

39.8 40.8 90.8 90 0.8
Type
6
6
3
4
59.8 60.8 110.8 110 0.8
89.8 90.8 140.8 140 0.8
119.8 120.8 170.8 170 0.8

149.8 150.8 200.8 200 0.8
6
6
4
4
19.8 20.8 70.8 70 0.8

39.9 40.9 90.9 90 0.9
6
6
3
4
59.9 60.9 110.9 110 0.9
89.9 90.9 140.9 140 0.9
119.9 120.9 170.9 170 0.9

149.9 150.9 200.9 200 0.9
6
6
4
4
19.8 20.8 70.8 70 0.8

39.9 40.9 90.9 90 0.9
6
6
3
4
59.9 60.9 110.9 110 0.9
89.9 90.9 140.9 140 0.9
119.9 120.9 170.9 170 0.9

149.9 150.9 200.9 200 0.9
6
6
4
4
19.8 20.8 70.8 70 0.8

39.9 40.9 90.9 90 0.9
6
6
3
4
59.9 60.9 110.9 110 0.9
89.9 90.9 140.9 140 0.9
119.9 120.9 170.9 170 0.9

149.9 150.9 200.9 200 0.9
6
6
4
4
19.9 20.9 70.9 70 0.9

39.9 40.9 90.9 90 0.9
6
6
3
4
59.9 60.9 110.9 110 0.9
89.9 90.9 140.9 140 0.9
119.9 120.9 170.9 170 0.9

149.9 150.9 200.9 200 0.9
6
6
4
4
30.4 30.9 80.9 80 0.9

60.4 60.9 110.9 110 0.9
6
6
3
4
90.4 90.9 140.9 140 0.9
120.4 120.9 170.9 170 0.9

150.4 150.9 200.9 200 0.9
6
6
4
4
30.4 30.9 80.9 80 0.9

60.4 60.9 110.9 110 0.9
6
6
3
4
90.4 90.9 140.9 140 0.9
120.4 120.9 170.9 170 0.9

150.4 150.9 200.9 200 0.9
6
6
4
4
30.4 30.9 80.9 80 0.9

60.5 61.0 111.0 110 1.0
6
6
3
4
90.5 91.0 141.0 140 1.0
120.5 121.0 171.0 170 1.0

150.5 151.0 201.0 200 1.0
6
6
4
4
30.4 30.9 80.9 80 0.9

60.5 61.0 111.0 110 1.0
6
6
3
4
90.5 91.0 141.0 140 1.0
120.5 121.0 171.0 170 1.0

150.5 151.0 201.0 200 1.0
6
6
4
4
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N093
N094
Q001
DRILLING
22
30
23
30
60.7 60.7 110.7 110 0.7
DCON
3.7 14
PL
17
LF
3
8
40.7 40.7 90.7 90 0.7
(mm) (l/d)
OAL
10
MHS0460L020B
MHS0460L040B
MHS0460L060B
MHS0460L090B
MHS0460L120B
MHS0460L150B
MHS0470L020B
MHS0470L040B
MHS0470L060B
MHS0470L090B
MHS0470L120B
MHS0470L150B
MHS0480L020B
MHS0480L040B
MHS0480L060B
MHS0480L090B
MHS0480L120B
MHS0480L150B
MHS0490L020B
MHS0490L040B
MHS0490L060B
MHS0490L090B
MHS0490L120B
MHS0490L150B
MHS0500L020B
MHS0500L040B
MHS0500L060B
MHS0500L090B
MHS0500L120B
MHS0500L150B
MHS0510L030B
MHS0510L060B
MHS0510L090B
MHS0510L120B
MHS0510L150B
MHS0520L030B
MHS0520L060B
MHS0520L090B
MHS0520L120B
MHS0520L150B
MHS0530L030B
MHS0530L060B
MHS0530L090B
MHS0530L120B
MHS0530L150B
MHS0540L030B
MHS0540L060B
MHS0540L090B
MHS0540L120B
MHS0540L150B
LH
22
30
LCF
VP15TF
3.6 14
Dimensions (mm)
2
6
DCON
20.6 20.6 70.6 70 0.6
PL
MHS0360L020B
MHS0360L040B
MHS0360L060B
MHS0360L090B
MHS0360L120B
MHS0370L020B
MHS0370L040B
MHS0370L060B
MHS0370L090B
MHS0370L120B
MHS0380L020B
MHS0380L040B
MHS0380L060B
MHS0380L090B
MHS0380L120B
MHS0390L020B
MHS0390L040B
MHS0390L060B
MHS0390L090B
MHS0390L120B
MHS0400L020B
MHS0400L040B
MHS0400L060B
MHS0400L090B
MHS0400L120B
MHS0410L020B
MHS0410L040B
MHS0410L060B
MHS0410L090B
MHS0410L120B
MHS0420L020B
MHS0420L040B
MHS0420L060B
MHS0420L090B
MHS0420L120B
MHS0430L020B
MHS0430L040B
MHS0430L060B
MHS0430L090B
MHS0430L120B
MHS0440L020B
MHS0440L040B
MHS0440L060B
MHS0440L090B
MHS0440L120B
MHS0450L020B
MHS0450L040B
MHS0450L060B
MHS0450L090B
MHS0450L120B
LF
OAL
LH
(mm) (l/d)
DC
Stock
Order Number
Type
LCF
Order Number
Hole Depth
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
N087
MHS
WSTAR DRILLS
5.7 13
19
24
3
8
5.8 13
18
23
3
8
5.9 13
18
23
2
7
6.0 12
17
22
2
7
6.1 12
17
22
2
7
6.2 12
17
21
2
7
6.3 12
16
21
2
7
6.4 11
16
21
DRILLING
6.5 11
120.5 121.0 171.0 170 1.0

150.5 151.0 201.0 200 1.0
6
6
4
4
16
20
31.0 31.0 81.0 80 1.0

61.0 61.0 111.0 110 1.0
6
6
3
4
2
6
91.0 91.0 141.0 140 1.0
11
121.0 121.0 171.0 170 1.0

151.0 151.0 201.0 200 1.0
6
6
4
4
16
r
r
31.0 31.0 81.0 80 1.0

61.0 61.0 111.0 110 1.0
6
6
3
4
20
28
2
6
91.0 91.0 141.0 140 1.0

121.0 121.0 171.0 170 1.0
151.0 151.0 201.0 200 1.0
6
6
4
4
11
15
31.0 31.0 81.0 80 1.0

61.1 61.1 111.1 110 1.1
6
6
3
4
20
27
91.1 91.1 141.1 140 1.1
121.1 121.1 171.1 170 1.1

151.1 151.1 201.1 200 1.1
6
6
4
4
2
6
11
31.0 31.0 81.0 80 1.0

61.1 61.1 111.1 110 1.1
6
6
3
4
15
19
27
91.1 91.1 141.1 140 1.1

121.1 121.1 171.1 170 1.1
151.1 151.1 201.1 200 1.1
6
6
4
4
2
6
31.0 31.0 81.0 80 1.0

61.1 61.1 111.1 110 1.1
6
6
3
4
10
15
19
26
2
6
10
14
6.6
6.7
6.8
6.9
91.1 91.1 141.1 140 1.1
121.1 121.1 171.1 170 1.1

151.1 151.1 201.1 200 1.1
6
6
4
4
29.6 31.1 81.1 80 1.1

59.6 61.1 111.1 110 1.1
8
8
3
4
89.6 91.1 141.1 140 1.1
119.6 121.1 171.1 170 1.1

149.6 151.1 201.1 200 1.1
8
8
4
4
19
26
29.6 31.1 81.1 80 1.1

59.6 61.1 111.1 110 1.1
8
8
3
4
2
6
10
14
19
26
2
6
10
14
18
25
89.6 91.1 141.1 140 1.1
119.6 121.1 171.1 170 1.1

149.6 151.1 201.1 200 1.1
8
8
4
4
29.6 31.1 81.1 80 1.1

59.6 61.1 111.1 110 1.1
8
8
3
4
89.6 91.1 141.1 140 1.1
119.6 121.1 171.1 170 1.1

149.6 151.1 201.1 200 1.1
8
8
4
4
29.6 31.1 81.1 80 1.1

59.7 61.2 111.2 110 1.2
8
8
3
4
89.7 91.2 141.2 140 1.2
119.7 121.2 171.2 170 1.2

149.7 151.2 201.2 200 1.2
8
8
4
4
7.0
7.1
7.2
N088
29.6 31.1 81.1 80 1.1

59.7 61.2 111.2 110 1.2
DCON
3
8
90.5 91.0 141.0 140 1.0
MHS0650L030B
MHS0650L060B
MHS0650L090B
MHS0650L120B
MHS0650L150B
MHS0660L030B
MHS0660L060B
MHS0660L090B
MHS0660L120B
MHS0660L150B
MHS0660L200B
MHS0670L030B
MHS0670L060B
MHS0670L090B
MHS0670L120B
MHS0670L150B
MHS0670L200B
MHS0680L030B
MHS0680L060B
MHS0680L090B
MHS0680L120B
MHS0680L150B
MHS0680L200B
MHS0690L030B
MHS0690L060B
MHS0690L090B
MHS0690L120B
MHS0690L150B
MHS0690L200B
MHS0700L030B
MHS0700L060B
MHS0700L090B
MHS0700L120B
MHS0700L150B
MHS0700L200B
MHS0710L030B
MHS0710L060B
MHS0710L090B
MHS0710L120B
MHS0710L150B
MHS0710L200B
MHS0720L030B
MHS0720L060B
MHS0720L090B
MHS0720L120B
MHS0720L150B
MHS0720L200B
PL
19
24
LF
2
6
(mm) (l/d)
OAL
5.6 14
3
4
LH
VP15TF
3
8
Hole Depth
DCON
19
25
6
6
PL
30.4 30.9 80.9 80 0.9

60.5 61.0 111.0 110 1.0
LF
5.5 14
MHS0550L030B
MHS0550L060B
MHS0550L090B
MHS0550L120B
MHS0550L150B
MHS0560L030B
MHS0560L060B
MHS0560L090B
MHS0560L120B
MHS0560L150B
MHS0570L030B
MHS0570L060B
MHS0570L090B
MHS0570L120B
MHS0570L150B
MHS0580L030B
MHS0580L060B
MHS0580L090B
MHS0580L120B
MHS0580L150B
MHS0590L030B
MHS0590L060B
MHS0590L090B
MHS0590L120B
MHS0590L150B
MHS0600L030B
MHS0600L060B
MHS0600L090B
MHS0600L120B
MHS0600L150B
MHS0610L030B
MHS0610L060B
MHS0610L090B
MHS0610L120B
MHS0610L150B
MHS0620L030B
MHS0620L060B
MHS0620L090B
MHS0620L120B
MHS0620L150B
MHS0630L030B
MHS0630L060B
MHS0630L090B
MHS0630L120B
MHS0630L150B
MHS0640L030B
MHS0640L060B
MHS0640L090B
MHS0640L120B
MHS0640L150B
OAL
Dimensions (mm)
Order Number
LH
3
8
DC
Stock
Type
LCF
Order Number
(mm) (l/d)
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
Type
8
8
3
4
89.7 91.2 141.2 140 1.2
119.7 121.2 171.2 170 1.2

149.7 151.2 201.2 200 1.2
8
8
4
4
30.1 31.1 81.1 80 1.1

60.2 61.2 111.2 110 1.2
8
8
3
4
90.2 91.2 141.2 140 1.2
120.2 121.2 171.2 170 1.2
150.2 151.2 201.2 200 1.2

200.2 201.2 251.2 250 1.2
8
8
4
4
30.2 31.2 81.2 80 1.2

60.2 61.2 111.2 110 1.2
8
8
3
4
90.2 91.2 141.2 140 1.2
120.2 121.2 171.2 170 1.2
150.2 151.2 201.2 200 1.2

200.2 201.2 251.2 250 1.2
8
8
4
4
30.2 31.2 81.2 80 1.2

60.2 61.2 111.2 110 1.2
8
8
3
4
90.2 91.2 141.2 140 1.2
120.2 121.2 171.2 170 1.2
150.2 151.2 201.2 200 1.2

200.2 201.2 251.2 250 1.2
8
8
4
4
30.2 31.2 81.2 80 1.2

60.3 61.3 111.3 110 1.3
8
8
3
4
90.3 91.3 141.3 140 1.3
120.3 121.3 171.3 170 1.3
150.3 151.3 201.3 200 1.3

200.3 201.3 251.3 250 1.3
8
8
4
4
30.2 31.2 81.2 80 1.2

60.3 61.3 111.3 110 1.3
8
8
3
4
90.3 91.3 141.3 140 1.3
120.3 121.3 171.3 170 1.3
150.3 151.3 201.3 200 1.3

200.3 201.3 251.3 250 1.3
8
8
4
4
30.7 31.2 81.2 80 1.2

60.8 61.3 111.3 110 1.3
8
8
3
4
90.8 91.3 141.3 140 1.3
120.8 121.3 171.3 170 1.3
150.8 151.3 201.3 200 1.3

200.8 201.3 251.3 250 1.3
8
8
4
4
30.7 31.2 81.2 80 1.2

60.8 61.3 111.3 110 1.3
8
8
3
4
90.8 91.3 141.3 140 1.3
120.8 121.3 171.3 170 1.3
150.8 151.3 201.3 200 1.3

200.8 201.3 251.3 250 1.3
8
8
4
4
CARBIDE
14
18
24
1
5
13
17
24
1
5
7.6 13
17
24
30
1
5
7.7 13
7.4
7.5
17
23
30
1
5
7.8 13
17
23
30
1
5
7.9 13
16
23
29
120.8 121.3 171.3 170 1.3
8.0 12
150.8 151.3 201.3 200 1.3

200.8 201.3 251.3 250 1.3
8
8
4
4
16
a
a
30.8 31.3 81.3 80 1.3

60.8 61.3 111.3 110 1.3
8
8
3
4
22
29
90.8 91.3 141.3 140 1.3
2
8
120.8 121.3 171.3 170 1.3
12
150.8 151.3 201.3 200 1.3

200.8 201.3 251.3 250 1.3
8
8
4
4
16
r
r
30.8 31.3 81.3 80 1.3

60.9 61.4 111.4 110 1.4
8
8
3
4
22
28
90.9 91.4 141.4 140 1.4
2
8
120.9 121.4 171.4 170 1.4
12
150.9 151.4 201.4 200 1.4

200.9 201.4 251.4 250 1.4
8
8
4
4
16
r
r
31.3 31.3 81.3 80 1.3

61.4 61.4 111.4 110 1.4
8
8
3
4
22
28
2
8
91.4 91.4 141.4 140 1.4

121.4 121.4 171.4 170 1.4
12
151.4 151.4 201.4 200 1.4
15
r
r
8.1
8.2
8.3
201.4 201.4 251.4 250 1.4

251.4 251.4 301.4 300 1.4
8
8
4
4
21
27
31.3 31.3 81.3 80 1.3

61.4 61.4 111.4 110 1.4
8
8
3
4
2
8
91.4 91.4 141.4 140 1.4
12
15
21
27
2
8
11
15
a
a
121.4 121.4 171.4 170 1.4
151.4 151.4 201.4 200 1.4
201.4 201.4 251.4 250 1.4

251.4 251.4 301.4 300 1.4
8
8
4
4
31.3 31.3 81.3 80 1.3

61.4 61.4 111.4 110 1.4
8
8
3
4
8.4
8.5
91.4 91.4 141.4 140 1.4
121.4 121.4 171.4 170 1.4
151.4 151.4 201.4 200 1.4
21
27
201.4 201.4 251.4 250 1.4

251.4 251.4 301.4 300 1.4
8
8
4
4
2
8
31.4 31.4 81.4 80 1.4

61.4 61.4 111.4 110 1.4
8
8
3
4
11
15
91.4 91.4 141.4 140 1.4
121.4 121.4 171.4 170 1.4
21
26
151.4 151.4 201.4 200 1.4
201.4 201.4 251.4 250 1.4

251.4 251.4 301.4 300 1.4
8
8
4
4
2
8
11
15
20
26
8.6
8.7
31.4 31.4 81.4 80 1.4

61.5 61.5 111.5 110 1.5
8
8
3
4
91.5 91.5 141.5 140 1.5
121.5 121.5 171.5 170 1.5
151.5 151.5 201.5 200 1.5
201.5 201.5 251.5 250 1.5

251.5 251.5 301.5 300 1.5
8
8
4
4
39.9 41.4 101.4 100 1.4 10

90.0 91.5 151.5 150 1.5 10
3
4
120.0 121.5 181.5 180 1.5 10
150.0 151.5 211.5 210 1.5 10
200.0 201.5 261.5 260 1.5 10

250.0 251.5 311.5 310 1.5 10
4
4
39.9 41.4 101.4 100 1.4 10

90.0 91.5 151.5 150 1.5 10
3
4
120.0 121.5 181.5 180 1.5 10
150.0 151.5 211.5 210 1.5 10
200.0 201.5 261.5 260 1.5 10

250.0 251.5 311.5 310 1.5 10
4
4
39.9 41.4 101.4 100 1.4 10

90.0 91.5 151.5 150 1.5 10
3
4
120.0 121.5 181.5 180 1.5 10
150.0 151.5 211.5 210 1.5 10
200.0 201.5 261.5 260 1.5 10

250.0 251.5 311.5 310 1.5 10
4
4
39.9 41.4 101.4 100 1.4 10

90.0 91.5 151.5 150 1.5 10
3
4
120.0 121.5 181.5 180 1.5 10
150.0 151.5 211.5 210 1.5 10
200.0 201.5 261.5 260 1.5 10

250.0 251.5 311.5 310 1.5 10
4
4
40.0 41.5 101.5 100 1.5 10

90.0 91.5 151.5 150 1.5 10
3
4
120.0 121.5 181.5 180 1.5 10
150.0 151.5 211.5 210 1.5 10
200.0 201.5 261.5 260 1.5 10

250.0 251.5 311.5 310 1.5 10
4
4
40.5 41.5 101.5 100 1.5 10

90.6 91.6 151.6 150 1.6 10
3
4
120.6 121.6 181.6 180 1.6 10
150.6 151.6 211.6 210 1.6 10
200.6 201.6 261.6 260 1.6 10

250.6 251.6 311.6 310 1.6 10
4
4
40.5 41.5 101.5 100 1.5 10

90.6 91.6 151.6 150 1.6 10
3
4
120.6 121.6 181.6 180 1.6 10
150.6 151.6 211.6 210 1.6 10
200.6 201.6 261.6 260 1.6 10

250.6 251.6 311.6 310 1.6 10
4
4
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N093
N094
Q001
DRILLING
10
DCON
90.8 91.3 141.3 140 1.3
MHS0800L030B
MHS0800L060B
MHS0800L090B
MHS0800L120B
MHS0800L150B
MHS0800L200B
MHS0800L250B
MHS0810L040B
MHS0810L090B
MHS0810L120B
MHS0810L150B
MHS0810L200B
MHS0810L250B
MHS0820L040B
MHS0820L090B
MHS0820L120B
MHS0820L150B
MHS0820L200B
MHS0820L250B
MHS0830L040B
MHS0830L090B
MHS0830L120B
MHS0830L150B
MHS0830L200B
MHS0830L250B
MHS0840L040B
MHS0840L090B
MHS0840L120B
MHS0840L150B
MHS0840L200B
MHS0840L250B
MHS0850L040B
MHS0850L090B
MHS0850L120B
MHS0850L150B
MHS0850L200B
MHS0850L250B
MHS0860L040B
MHS0860L090B
MHS0860L120B
MHS0860L150B
MHS0860L200B
MHS0860L250B
MHS0870L040B
MHS0870L090B
MHS0870L120B
MHS0870L150B
MHS0870L200B
MHS0870L250B
PL
1
6
LF
1
5
60.8 61.3 111.3 110 1.3
(mm) (l/d)
OAL
18
25
LH
Type
LCF
14
VP15TF
Hole Depth
10
DCON
30.8 31.3 81.3 80 1.3
PL
MHS0730L030B
MHS0730L060B
MHS0730L090B
MHS0730L120B
MHS0730L150B
MHS0730L200B
MHS0740L030B
MHS0740L060B
MHS0740L090B
MHS0740L120B
MHS0740L150B
MHS0740L200B
MHS0750L030B
MHS0750L060B
MHS0750L090B
MHS0750L120B
MHS0750L150B
MHS0750L200B
MHS0760L030B
MHS0760L060B
MHS0760L090B
MHS0760L120B
MHS0760L150B
MHS0760L200B
MHS0760L250B
MHS0770L030B
MHS0770L060B
MHS0770L090B
MHS0770L120B
MHS0770L150B
MHS0770L200B
MHS0770L250B
MHS0780L030B
MHS0780L060B
MHS0780L090B
MHS0780L120B
MHS0780L150B
MHS0780L200B
MHS0780L250B
MHS0790L030B
MHS0790L060B
MHS0790L090B
MHS0790L120B
MHS0790L150B
MHS0790L200B
MHS0790L250B
LF
OAL
Dimensions (mm)
Order Number
LH
(mm) (l/d)
DC
Stock
Type
LCF
Order Number
7.3
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
N089
MHS
WSTAR DRILLS
11
14
20
25
2
7
11
14
20
25
8.9
9.0
2
7
11
9.1 14
19
25
30
2
7
10
9.2 14
19
25
30
2
7
9.3 14
19
24
30
2
7
10
9.4 13
19
24
29
DRILLING
10
150.6 151.6 211.6 210 1.6 10
9.5 13
200.6 201.6 261.6 260 1.6 10

250.6 251.6 311.6 310 1.6 10
4
4
18
3
4
24
29
40.5 41.5 101.5 100 1.5 10

90.6 91.6 151.6 150 1.6 10
120.6 121.6 181.6 180 1.6 10
2
7
150.6 151.6 211.6 210 1.6 10
10
200.6 201.6 261.6 260 1.6 10

250.6 251.6 311.6 310 1.6 10
4
4
9.6 13
18
40.5 41.5 101.5 100 1.5 10

90.6 91.6 151.6 150 1.6 10
3
4
24
29
120.6 121.6 181.6 180 1.6 10
4
4
2
7
150.6 151.6 211.6 210 1.6 10

200.6 201.6 261.6 260 1.6 10
250.6 251.6 311.6 310 1.6 10
4
4
10
9.7 13
41.1 41.6 101.6 100 1.6 10

91.2 91.7 151.7 150 1.7 10
3
4
18
r
r
121.2 121.7 181.7 180 1.7 10
23
28
2
7
10
9.8 13
18
23
28
151.2 151.7 211.7 210 1.7 10
201.2 201.7 261.7 260 1.7 10
251.2 251.7 311.7 310 1.7 10

301.2 301.7 361.7 360 1.7 10
4
4
41.1 41.6 101.6 100 1.6 10

91.2 91.7 151.7 150 1.7 10
3
4
121.2 121.7 181.7 180 1.7 10
151.2 151.7 211.7 210 1.7 10
201.2 201.7 261.7 260 1.7 10
2
7
251.2 251.7 311.7 310 1.7 10

301.2 301.7 361.7 360 1.7 10
4
4
10
9.9 13
41.1 41.6 101.6 100 1.6 10

91.2 91.7 151.7 150 1.7 10
3
4
18
r
r
121.2 121.7 181.7 180 1.7 10
23
28
151.2 151.7 211.7 210 1.7 10
4
4
1
6
201.2 201.7 261.7 260 1.7 10

251.2 251.7 311.7 310 1.7 10
301.2 301.7 361.7 360 1.7 10
4
4
10.0 12
41.1 41.6 101.6 100 1.6 10

91.2 91.7 151.7 150 1.7 10
3
4
17
a
a
121.2 121.7 181.7 180 1.7 10
22
27
1
6
10.1 12
17
22
27
151.2 151.7 211.7 210 1.7 10
201.2 201.7 261.7 260 1.7 10
251.2 251.7 311.7 310 1.7 10

301.2 301.7 361.7 360 1.7 10
4
4
N090
DCON
2
7
10
PL
LF
20
26
120.6 121.6 181.6 180 1.6 10
MHS0950L040B
MHS0950L090B
MHS0950L120B
MHS0950L150B
MHS0950L200B
MHS0950L250B
MHS0950L300B
MHS0960L040B
MHS0960L090B
MHS0960L120B
MHS0960L150B
MHS0960L200B
MHS0960L250B
MHS0960L300B
MHS0970L040B
MHS0970L090B
MHS0970L120B
MHS0970L150B
MHS0970L200B
MHS0970L250B
MHS0970L300B
MHS0980L040B
MHS0980L090B
MHS0980L120B
MHS0980L150B
MHS0980L200B
MHS0980L250B
MHS0980L300B
MHS0990L040B
MHS0990L090B
MHS0990L120B
MHS0990L150B
MHS0990L200B
MHS0990L250B
MHS0990L300B
MHS1000L040B
MHS1000L090B
MHS1000L120B
MHS1000L150B
MHS1000L200B
MHS1000L250B
MHS1000L300B
MHS1010L040B
MHS1010L090B
MHS1010L120B
MHS1010L150B
MHS1010L200B
MHS1010L250B
MHS1010L300B
(mm) (l/d)
OAL
2
7
90.6 91.6 151.6 150 1.6 10
Type
LH
14
VP15TF
Hole Depth
11
DCON
Dimensions (mm)
40.5 41.5 101.5 100 1.5 10
PL
MHS0880L040B
MHS0880L090B
MHS0880L120B
MHS0880L150B
MHS0880L200B
MHS0880L250B
MHS0890L040B
MHS0890L090B
MHS0890L120B
MHS0890L150B
MHS0890L200B
MHS0890L250B
MHS0900L040B
MHS0900L090B
MHS0900L120B
MHS0900L150B
MHS0900L200B
MHS0900L250B
MHS0910L040B
MHS0910L090B
MHS0910L120B
MHS0910L150B
MHS0910L200B
MHS0910L250B
MHS0910L300B
MHS0920L040B
MHS0920L090B
MHS0920L120B
MHS0920L150B
MHS0920L200B
MHS0920L250B
MHS0920L300B
MHS0930L040B
MHS0930L090B
MHS0930L120B
MHS0930L150B
MHS0930L200B
MHS0930L250B
MHS0930L300B
MHS0940L040B
MHS0940L090B
MHS0940L120B
MHS0940L150B
MHS0940L200B
MHS0940L250B
MHS0940L300B
LF
OAL
LH
(mm) (l/d)
DC
Stock
Order Number
LCF
Order Number
8.8
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
LCF
CARBIDE
Type
41.1 41.6 101.6 100 1.6 10

91.2 91.7 151.7 150 1.7 10
3
4
121.2 121.7 181.7 180 1.7 10
151.2 151.7 211.7 210 1.7 10
201.2 201.7 261.7 260 1.7 10
251.2 251.7 311.7 310 1.7 10

301.2 301.7 361.7 360 1.7 10
4
4
41.7 41.7 101.7 100 1.7 10

91.7 91.7 151.7 150 1.7 10
3
4
121.7 121.7 181.7 180 1.7 10
151.7 151.7 211.7 210 1.7 10
201.7 201.7 261.7 260 1.7 10
251.7 251.7 311.7 310 1.7 10

301.7 301.7 361.7 360 1.7 10
4
4
41.7 41.7 101.7 100 1.7 10

91.8 91.8 151.8 150 1.8 10
3
4
121.8 121.8 181.8 180 1.8 10
151.8 151.8 211.8 210 1.8 10
201.8 201.8 261.8 260 1.8 10
251.8 251.8 311.8 310 1.8 10

301.8 301.8 361.8 360 1.8 10
4
4
41.7 41.7 101.7 100 1.7 10

91.8 91.8 151.8 150 1.8 10
3
4
121.8 121.8 181.8 180 1.8 10
151.8 151.8 211.8 210 1.8 10
201.8 201.8 261.8 260 1.8 10
251.8 251.8 311.8 310 1.8 10

301.8 301.8 361.8 360 1.8 10
4
4
41.7 41.7 101.7 100 1.7 10

91.8 91.8 151.8 150 1.8 10
3
4
121.8 121.8 181.8 180 1.8 10
151.8 151.8 211.8 210 1.8 10
201.8 201.8 261.8 260 1.8 10
251.8 251.8 311.8 310 1.8 10

301.8 301.8 361.8 360 1.8 10
4
4
41.7 41.7 101.7 100 1.7 10

91.8 91.8 151.8 150 1.8 10
3
4
121.8 121.8 181.8 180 1.8 10
151.8 151.8 211.8 210 1.8 10
201.8 201.8 261.8 260 1.8 10
251.8 251.8 311.8 310 1.8 10

301.8 301.8 361.8 360 1.8 10
4
4
40.2 41.7 101.7 100 1.7 12

90.3 91.8 151.8 150 1.8 12
3
4
120.3 121.8 181.8 180 1.8 12
150.3 151.8 211.8 210 1.8 12
200.3 201.8 261.8 260 1.8 12
250.3 251.8 311.8 310 1.8 12

300.3 301.8 361.8 360 1.8 12
4
4
CARBIDE
17
22
27
1
6
10.3 12
17
22
26
1
6
10.4 12
17
21
26
1
6
10.5 12
16
21
26
1
6
10.6 12
16
21
26
1
6
10.7 11
16
21
25
1
6
10.8 11
16
21
25
10.9 11
200.4 201.9 261.9 260 1.9 12
16
250.4 251.9 311.9 310 1.9 12

300.4 301.9 361.9 360 1.9 12
4
4
20
25
40.3 41.8 101.8 100 1.8 12

90.4 91.9 151.9 150 1.9 12
3
4
1
6
120.4 121.9 181.9 180 1.9 12
150.4 151.9 211.9 210 1.9 12
11.0 11
200.4 201.9 261.9 260 1.9 12
16
250.4 251.9 311.9 310 1.9 12

300.4 301.9 361.9 360 1.9 12
4
4
20
25
40.3 41.8 101.8 100 1.8 12

90.4 91.9 151.9 150 1.9 12
3
4
1
6
120.4 121.9 181.9 180 1.9 12
150.4 151.9 211.9 210 1.9 12
11.1 11
200.4 201.9 261.9 260 1.9 12
15
250.4 251.9 311.9 310 1.9 12

300.4 301.9 361.9 360 1.9 12
4
4
20
24
40.3 41.8 101.8 100 1.8 12

90.4 91.9 151.9 150 1.9 12
3
4
1
5
120.4 121.9 181.9 180 1.9 12
150.4 151.9 211.9 210 1.9 12
11.2 11
200.4 201.9 261.9 260 1.9 12
15
250.4 251.9 311.9 310 1.9 12

300.4 301.9 361.9 360 1.9 12
4
4
20
24
40.8 41.8 101.8 100 1.8 12

90.9 91.9 151.9 150 1.9 12
3
4
1
5
120.9 121.9 181.9 180 1.9 12
150.9 151.9 211.9 210 1.9 12
11.3 11
200.9 201.9 261.9 260 1.9 12
15
250.9 251.9 311.9 310 1.9 12

300.9 301.9 361.9 360 1.9 12
4
4
20
24
40.8 41.8 101.8 100 1.8 12

90.9 91.9 151.9 150 1.9 12
3
4
1
5
120.9 121.9 181.9 180 1.9 12
150.9 151.9 211.9 210 1.9 12
11.4 11
200.9 201.9 261.9 260 1.9 12
15
250.9 251.9 311.9 310 1.9 12

300.9 301.9 361.9 360 1.9 12
4
4
19
24
40.9 41.9 101.9 100 1.9 12

91.0 92.0 152.0 150 2.0 12
3
4
1
5
121.0 122.0 182.0 180 2.0 12
151.0 152.0 212.0 210 2.0 12
11.5 10
201.0 202.0 262.0 260 2.0 12
15
251.0 252.0 312.0 310 2.0 12

301.0 302.0 362.0 360 2.0 12
4
4
19
24
DCON
150.4 151.9 211.9 210 1.9 12
PL
120.4 121.9 181.9 180 1.9 12
MHS1090L040B
MHS1090L090B
MHS1090L120B
MHS1090L150B
MHS1090L200B
MHS1090L250B
MHS1090L300B
MHS1100L040B
MHS1100L090B
MHS1100L120B
MHS1100L150B
MHS1100L200B
MHS1100L250B
MHS1100L300B
MHS1110L040B
MHS1110L090B
MHS1110L120B
MHS1110L150B
MHS1110L200B
MHS1110L250B
MHS1110L300B
MHS1120L040B
MHS1120L090B
MHS1120L120B
MHS1120L150B
MHS1120L200B
MHS1120L250B
MHS1120L300B
MHS1130L040B
MHS1130L090B
MHS1130L120B
MHS1130L150B
MHS1130L200B
MHS1130L250B
MHS1130L300B
MHS1140L040B
MHS1140L090B
MHS1140L120B
MHS1140L150B
MHS1140L200B
MHS1140L250B
MHS1140L300B
MHS1150L040B
MHS1150L090B
MHS1150L120B
MHS1150L150B
MHS1150L200B
MHS1150L250B
MHS1150L300B
LF
OAL
LH
LCF
90.4 91.9 151.9 150 1.9 12
Type
Type
40.9 41.9 101.9 100 1.9 12
91.0 92.0 152.0 150 2.0 12
121.0 122.0 182.0 180 2.0 12
151.0 152.0 212.0 210 2.0 12
201.0 202.0 262.0 260 2.0 12
251.0 252.0 312.0 310 2.0 12

301.0 302.0 362.0 360 2.0 12
4
4
40.9 41.9 101.9 100 1.9 12

91.0 92.0 152.0 150 2.0 12
3
4
121.0 122.0 182.0 180 2.0 12
151.0 152.0 212.0 210 2.0 12
201.0 202.0 262.0 260 2.0 12
251.0 252.0 312.0 310 2.0 12

301.0 302.0 362.0 360 2.0 12
4
4
41.4 41.9 101.9 100 1.9 12

91.5 92.0 152.0 150 2.0 12
3
4
121.5 122.0 182.0 180 2.0 12
151.5 152.0 212.0 210 2.0 12
201.5 202.0 262.0 260 2.0 12
251.5 252.0 312.0 310 2.0 12

301.5 302.0 362.0 360 2.0 12
4
4
41.4 41.9 101.9 100 1.9 12

91.5 92.0 152.0 150 2.0 12
3
4
121.5 122.0 182.0 180 2.0 12
151.5 152.0 212.0 210 2.0 12
201.5 202.0 262.0 260 2.0 12
251.5 252.0 312.0 310 2.0 12

301.5 302.0 362.0 360 2.0 12
4
4
41.4 41.9 101.9 100 1.9 12

91.6 92.1 152.1 150 2.1 12
3
4
121.6 122.1 182.1 180 2.1 12
151.6 152.1 212.1 210 2.1 12
201.6 202.1 262.1 260 2.1 12
251.6 252.1 312.1 310 2.1 12

301.6 302.1 362.1 360 2.1 12
4
4
41.5 42.0 102.0 100 2.0 12

91.6 92.1 152.1 150 2.1 12
3
4
121.6 122.1 182.1 180 2.1 12
151.6 152.1 212.1 210 2.1 12
201.6 202.1 262.1 260 2.1 12
251.6 252.1 312.1 310 2.1 12

301.6 302.1 362.1 360 2.1 12
4
4
41.5 42.0 102.0 100 2.0 12

91.6 92.1 152.1 150 2.1 12
3
4
121.6 122.1 182.1 180 2.1 12
151.6 152.1 212.1 210 2.1 12
201.6 202.1 262.1 260 2.1 12
251.6 252.1 312.1 310 2.1 12

301.6 302.1 362.1 360 2.1 12
4
4
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N093
N094
Q001
DRILLING
10.2 12
VP15TF
(mm) (l/d)
DCON
Dimensions (mm)
40.3 41.8 101.8 100 1.8 12
PL
MHS1020L040B
MHS1020L090B
MHS1020L120B
MHS1020L150B
MHS1020L200B
MHS1020L250B
MHS1020L300B
MHS1030L040B
MHS1030L090B
MHS1030L120B
MHS1030L150B
MHS1030L200B
MHS1030L250B
MHS1030L300B
MHS1040L040B
MHS1040L090B
MHS1040L120B
MHS1040L150B
MHS1040L200B
MHS1040L250B
MHS1040L300B
MHS1050L040B
MHS1050L090B
MHS1050L120B
MHS1050L150B
MHS1050L200B
MHS1050L250B
MHS1050L300B
MHS1060L040B
MHS1060L090B
MHS1060L120B
MHS1060L150B
MHS1060L200B
MHS1060L250B
MHS1060L300B
MHS1070L040B
MHS1070L090B
MHS1070L120B
MHS1070L150B
MHS1070L200B
MHS1070L250B
MHS1070L300B
MHS1080L040B
MHS1080L090B
MHS1080L120B
MHS1080L150B
MHS1080L200B
MHS1080L250B
MHS1080L300B
LF
OAL
LH
(mm) (l/d)
DC
Stock
Order Number
LCF
Order Number
Hole Depth
Internal Coolant
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
N091

CARBIDE
MHS
WSTAR DRILLS
11.6 10
15
19
23
1
5
11.7 10
15
19
23
1
5
11.8 10
14
19
23
1
5
11.9 10
14
19
23
1
5
12.0 10
14
18
22
a
a
DCON
PL
MHS1160L040B
MHS1160L090B
MHS1160L120B
MHS1160L150B
MHS1160L200B
MHS1160L250B
MHS1160L300B
MHS1170L040B
MHS1170L090B
MHS1170L120B
MHS1170L150B
MHS1170L200B
MHS1170L250B
MHS1170L300B
MHS1180L040B
MHS1180L090B
MHS1180L120B
MHS1180L150B
MHS1180L200B
MHS1180L250B
MHS1180L300B
MHS1190L040B
MHS1190L090B
MHS1190L120B
MHS1190L150B
MHS1190L200B
MHS1190L250B
MHS1190L300B
MHS1200L040B
MHS1200L090B
MHS1200L120B
MHS1200L150B
MHS1200L200B
MHS1200L250B
MHS1200L300B
LF
r
r
OAL
1
5
(mm) (l/d)
LH
Order Number
LCF
Dimensions (mm)
VP15TF
DC
Hole Depth
Internal Coolant
Stock
Type
42.0 42.0 102.0 100 2.0 12
92.1 92.1 152.1 150 2.1 12
122.1 122.1 182.1 180 2.1 12
152.1 152.1 212.1 210 2.1 12
202.1 202.1 262.1 260 2.1 12
252.1 252.1 312.1 310 2.1 12

302.1 302.1 362.1 360 2.1 12
4
4
42.0 42.0 102.0 100 2.0 12

92.1 92.1 152.1 150 2.1 12
3
4
122.1 122.1 182.1 180 2.1 12
152.1 152.1 212.1 210 2.1 12
202.1 202.1 262.1 260 2.1 12
252.1 252.1 312.1 310 2.1 12

302.1 302.1 362.1 360 2.1 12
4
4
42.0 42.0 102.0 100 2.0 12

92.1 92.1 152.1 150 2.1 12
3
4
122.1 122.1 182.1 180 2.1 12
152.1 152.1 212.1 210 2.1 12
202.1 202.1 262.1 260 2.1 12
252.1 252.1 312.1 310 2.1 12

302.1 302.1 362.1 360 2.1 12
4
4
42.0 42.0 102.0 100 2.0 12

92.2 92.2 152.2 150 2.2 12
3
4
122.2 122.2 182.2 180 2.2 12
152.2 152.2 212.2 210 2.2 12
202.2 202.2 262.2 260 2.2 12
252.2 252.2 312.2 310 2.2 12

302.2 302.2 362.2 360 2.2 12
4
4
42.1 42.1 102.1 100 2.1 12

92.2 92.2 152.2 150 2.2 12
3
4
122.2 122.2 182.2 180 2.2 12
152.2 152.2 212.2 210 2.2 12
202.2 202.2 262.2 260 2.2 12
252.2 252.2 312.2 310 2.2 12

302.2 302.2 362.2 360 2.2 12
4
4
DRILLING
N092
CARBIDE
Dia.
DC
(mm)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
Work
Material
Dia.
DC
(mm)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
Work
Material
Dia.
DC
(mm)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
Mild Steel ( < 180HB),

Ferritic, Precipitation hardening stainless steel (>200HB)
AISI 1010,

Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(min-1)
40
50
60
70
80
80
80
80
80
80
80
80
12700
13300
11900
11100
10200
8000
6400
5100
4000
3200
2600
2100
0.030
0.035
0.050
0.060
0.075
0.100
0.100
0.130
0.160
0.200
0.250
0.300
(0.020 0.040)
(0.025 0.050)
(0.030 0.065)
(0.040 0.080)
(0.050 0.100)
(0.070 0.130)
(0.090 0.110)
(0.110 0.140)
(0.140 0.180)
(0.180 0.230)
(0.220 0.280)
(0.270 0.340)
Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)
380
465
595
665
765
800
640
665
640
640
650
630
20
30
40
50
60
60
60
60
60
60
60
60
6400
8000
8000
8000
7600
6000
4800
3800
3000
2400
1900
1600
0.030
0.035
0.050
0.060
0.075
0.100
0.090
0.110
0.140
0.170
0.220
0.260
(0.020 0.040)
(0.025 0.050)
(0.030 0.065)
(0.040 0.080)
(0.050 0.100)
(0.070 0.130)
(0.080 0.090)
(0.100 0.120)
(0.130 0.150)
(0.160 0.190)
(0.200 0.230)
(0.240 0.280)
Pre-hardened steel (35 45HRC),

Alloy tool steel ( < 350 )
Hardened Steel (40 55HRC),

Precipitation hardening stainless steel (<450HB)
AISI P21, AISI P20,

ASTM H13, AISI L6 etc
AISI 431, AISI 420,

S17400, S17700 etc
Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(min-1)
20
30
40
50
60
60
60
60
60
60
60
60
6400
8000
8000
8000
7600
6000
4800
3800
3000
2400
1900
1600
0.025
0.030
0.040
0.045
0.060
0.080
0.080
0.110
0.130
0.170
0.210
0.250
(0.020 0.030)
(0.020 0.035)
(0.030 0.045)
(0.035 0.060)
(0.045 0.075)
(0.060 0.090)
(0.070 0.100)
(0.090 0.130)
(0.110 0.160)
(0.140 0.200)
(0.170 0.250)
(0.210 0.300)
160
240
320
360
455
480
385
420
390
410
400
400
AISI H13, L6,

Inconel718 etc
10
10
10
20
20
20
30
30
30
40
40
40
3200
2700
2000
3200
2600
2000
2400
1900
1500
1600
1300
1100
40
40
50
50
60
60
60
60
60
60
60
60
12700
10600
10000
8000
7600
6000
4800
3800
3000
2400
1900
1600
0.020
0.025
0.035
0.040
0.050
0.060
0.080
0.100
0.110
0.140
0.170
0.210
(0.015 0.025)
(0.020 0.030)
(0.025 0.040)
(0.030 0.050)
(0.040 0.065)
(0.050 0.080)
(0.060 0.100)
(0.080 0.130)
(0.090 0.130)
(0.120 0.160)
(0.140 0.200)
(0.170 0.240)
190
280
400
480
570
600
430
420
420
410
420
415
Table Feed
(mm/min)
255
265
350
320
380
360
385
380
330
335
325
335
(Note 1) When using the drill with a length over l/d 10, it is
necessary to use a prep holes as a guide. (If no prephole is used then drill breakage can occur)
(Note 2) Setting of the diameter tolerance differs from
general-purpose drills. MHS shortest flute drills are
recommended for prep hole machining.
Hardened Steel (40 55HRC),


(m/min)
(min-1)
Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)
Table Feed
(mm/min)
Feed rate
(Min.Max.)
(mm/rev)
Table Feed
(mm/min)
0.015 (0.015 0.020)

0.020 (0.015 0.025)
0.025 (0.020 0.030)
0.035 (0.025 0.040)
0.040 (0.030 0.050)
0.050 (0.040 0.070)
0.070 (0.050 0.080)
0.080 (0.060 0.100)
0.090 (0.080 0.110)
0.120 (0.100 0.130)
0.150 (0.130 0.170)
0.180 (0.150 0.200)
50
55
50
110
105
100
170
150
135
190
195
200
OPERATION GUIDANCE
TECHNICAL DATA
N094
Q001
DRILLING
Work
Material
N093

CARBIDE
MHS
WSTAR DRILLS
Drill Holding
Drill Length
Drill Installation
Coolant Method

Drill Installation
1DC
DRILLING
Stepped Holes
N094
A > DC x 2

1.5MPa7MPa
Recommended coolant pressure:
>3Mpa
Coolant Handling
Thin Workpiece
Interrupted Cutting
DC

diameter drills. Always
use a fine mesh filter as a
1) Make approx. 1DC(DC=drill

diameter) pilot hole by using the
MHS with the shortest flutes.
2) Use the pilot hole as a guide
and machine by the drill with
coolant hole. Depending on the
application, carry out pecking.

Revolving
Coolant
Machine Type
Adjusting Screw
Spindles
Through
Coolant Type

coolant exchange is
recommended.

cutting.
xChange the point angle.
One Process
If Bending
Occurs
zLower the feed

when drilling
the interrupted
part.
Requires Prior
Machining
Support
the Workpiece
zSpot face with

an end mill
prior to drilling.
CARBIDE
y OPERATIONAL GUIDANCE FOR THE MHS LONG TYPE DRILL (L/D>10)

zUse a drill with a larger (flatter) point angle than the super long type. Use
the shortest flute possible.

zPenetrate the guide hole at low revolution. (Revolution

1000min-1, feed rate 0.20.3mm/rev)
zAfter drilling, lower the cutting revolution about 0.5 1mm short of the
hole end. (Revolution of around 1000min-1)
3000mm/min.
cFinally, clear the hole at a cutting speed of 20 30m/min and feed rate
of 0.2 0.3mm/rev.
zPenetrate the guide hole at a low revolution. (Revolution

1000min-1, feed rate 0.2 0.3mm/rev)
xStop the long type drill 0.5 1mm short of the guide hole bottom.

xLower the feed rate when penetrating.
Use the shortest flute possible.

DRILLING
y 1. Spot facing
zFinally clear the hole at a cutting speed of 20 30m/min and feed rate of
0.2 0.3mm/rev.
3000mm/min.
TECHNICAL DATA
Q001
N095
MZE/MZS
P
Steel
a Helical coolant hole enables high speed machining
(MZS type).
DC<2 2 < DC < 3 3<DC < 6 6<DC < 10 10<DC < 18 18<DC < 20
0
0.014
(MZE only)
h6,h8
h6
MZE (External coolant)
MZE
MZS
0
0.014
0
0.014
0
0.006
0
0.022
0
0.022
0
0.009
LF
LCF = LH
PL
DCON
DC
OAL
MZS (Internal coolant)
LF
140
DC(h8)
PL
DCON(h6)
6
8
LCF
LH
PL
Type2
OAL
LF
DC
DCON(h6)
>
0
0.033
0
0.033
0
0.013
Type1
OAL
LF
LCF
LH
DCON < 2 : h
* DCON
2:h
0
0.027
0
0.027
0
0.011
140
DC(h8)
PL
0
0.018
0
0.018
0
0.008
DCON
CARBIDE
LCF
LH
OAL
Hole
Depth
Stock
Dimensions (mm)
Order Number
(mm)
(l/d)
VP15TF
DRILLING
DC
Coolant
(Int./Ext.)
(Note) MZS drills are suitable for use with shrink fit holders.
2
5
12
Ext.
1.0
Int.
Int.
Ext.
1.1
2
5
12
Int.
Int.
Ext.
1.2
2
5
12
Int.
Int.
2
5
12
Ext.
1.3
Int.
Int.
Ext.
1.4
2
5
12
Int.
Int.
2
5
12
Ext.
1.5
Int.
Int.
Ext.
1.6
2
5
12
Int.
Int.
Ext.
1.7
2
5
12
Int.
Int.
Ext.
1.8
2
5
12
Int.
Int.
Ext.
1.9
2
5
12
Int.
Int.
MZE0100SB
MZS0100LB
MZS0100XB
MZE0110SB
MZS0110LB
MZS0110XB
MZE0120SB
MZS0120LB
MZS0120XB
MZE0130SB
MZS0130LB
MZS0130XB
MZE0140SB
MZS0140LB
MZS0140XB
MZE0150SB
MZS0150LB
MZS0150XB
MZE0160SB
MZS0160LB
MZS0160XB
MZE0170SB
MZS0170LB
MZS0170XB
MZE0180SB
MZS0180LB
MZS0180XB
MZE0190SB
MZS0190LB
MZS0190XB
LH
OAL
LF
PL
DCON
6.2
11.2
23.2
8.2
15.2
27.2
55.2
55.2
55.2
55
55
55
0.2
0.2
0.2
2.0
3.0
3.0
1
2
2
7.2
17.2
23.2
9.2
21.2
27.2
55.2
55.2
55.2
55
55
55
0.2
0.2
0.2
2.0
3.0
3.0
1
2
2
8.2
17.2
23.2
9.2
20.2
26.2
55.2
55.2
55.2
55
55
55
0.2
0.2
0.2
2.0
3.0
3.0
1
2
2
8.2
17.2
23.2
9.2
20.2
26.2
55.2
55.2
55.2
55
55
55
0.2
0.2
0.2
2.0
3.0
3.0
1
2
2
9.3
17.3
23.3
10.3
20.3
26.3
55.3
55.3
55.3
55
55
55
0.3
0.3
0.3
2.0
3.0
3.0
1
2
2
9.3
17.3
23.3
10.3
20.3
26.3
55.3
55.3
55.3
55
55
55
0.3
0.3
0.3
2.0
3.0
3.0
1
2
2
10.3
22.3
30.3
10.3
25.3
33.3
55.3
68.3
68.3
55
68
68
0.3
0.3
0.3
2.0
3.0
3.0
1
2
2
10.3
22.3
30.3
10.3
24.3
32.3
55.3
68.3
68.3
55
68
68
0.3
0.3
0.3
2.0
3.0
3.0
1
2
2
11.3
22.3
30.3
11.3
24.3
32.3
55.3
68.3
68.3
55
68
68
0.3
0.3
0.3
2.0
3.0
3.0
1
2
2
11.3
22.3
30.3
11.3
24.3
32.3
55.3
68.3
68.3
55
68
68
0.3
0.3
0.3
2.0
3.0
3.0
1
2
2
N096
Type
LCF
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
Dimensions (mm)
Order Number
2
3
Ext.
Ext.
Int.
5
12
Int.
Int.
2
3
Ext.
Ext.
Int.
5
12
Int.
Int.
2
3
Ext.
Ext.
Int.
5
12
Int.
Int.
2
3
Ext.
Ext.
Int.
5
12
Int.
Int.
2
3
Ext.
Ext.
Int.
5
12
Int.
Int.
2
3
Ext.
Ext.
Int.
5
12
Int.
Int.
2
3
Ext.
Ext.
Int.
5
12
Int.
Int.
2
3
Ext.
Ext.
Int.
5
12
Int.
Int.
2
3
Ext.
Ext.
Int.
5
12
Int.
Int.
MZE0200SA
MZE0200MA
MZS0200MB
MZS0200LB
MZS0200XB
MZE0210SA
MZE0210MA
MZS0210MB
MZS0210LB
MZS0210XB
MZE0220SA
MZE0220MA
MZS0220MB
MZS0220LB
MZS0220XB
MZE0230SA
MZE0230MA
MZS0230MB
MZS0230LB
MZS0230XB
MZE0240SA
MZE0240MA
MZS0240MB
MZS0240LB
MZS0240XB
MZE0250SA
MZE0250MA
MZS0250MB
MZS0250LB
MZS0250XB
MZE0260SA
MZE0260MA
MZS0260MB
MZS0260LB
MZS0260XB
MZE0270SA
MZE0270MA
MZS0270MB
MZS0270LB
MZS0270XB
MZE0280SA
MZE0280MA
MZS0280MB
MZS0280LB
MZS0280XB
(l/d)
Type
LCF
LH
OAL
LF
PL
DCON
12.4
16.4
12.4
16.4
55.4
55.4
55
55
0.4
0.4
2.0
2.0
1
1
16.4
18.4
62.4
62
0.4
3.0
22.4
30.4
24.4
32.4
68.4
68.4
68
68
0.4
0.4
3.0
3.0
2
2
12.4
16.4
12.4
16.4
55.4
55.4
55
55
0.4
0.4
2.1
2.1
1
1
20.4
22.4
66.4
66
0.4
3.0
28.4
38.4
30.4
40.4
74.4
74.4
74
74
0.4
0.4
3.0
3.0
2
2
13.4
18.4
13.4
18.4
55.4
55.4
55
55
0.4
0.4
2.2
2.2
1
1
20.4
21.4
66.4
66
0.4
3.0
28.4
38.4
29.4
39.4
74.4
74.4
74
74
0.4
0.4
3.0
3.0
2
2
13.4
18.4
13.4
18.4
55.4
55.4
55
55
0.4
0.4
2.3
2.3
1
1
20.4
21.4
66.4
66
0.4
3.0
28.4
38.4
29.4
39.4
74.4
74.4
74
74
0.4
0.4
3.0
3.0
2
2
16.4
20.4
16.4
20.4
55.4
55.4
55
55
0.4
0.4
2.4
2.4
1
1
20.4
21.4
66.4
66
0.4
3.0
28.4
38.4
29.4
39.4
74.4
74.4
74
74
0.4
0.4
3.0
3.0
2
2
16.5
20.5
16.5
20.5
55.5
55.5
55
55
0.5
0.5
2.5
2.5
1
1
20.5
21.5
66.5
66
0.5
3.0
28.5
38.5
29.5
39.5
74.5
74.5
74
74
0.5
0.5
3.0
3.0
2
2
16.5
20.5
16.5
20.5
55.5
55.5
55
55
0.5
0.5
2.6
2.6
1
1
24.5
24.5
72.5
72
0.5
3.0
33.5
45.5
33.5
45.5
81.5
81.5
81
81
0.5
0.5
3.0
3.0
2
2
16.5
20.5
16.5
20.5
55.5
55.5
55
55
0.5
0.5
2.7
2.7
1
1
24.5
24.5
72.5
72
0.5
3.0
33.5
45.5
33.5
45.5
81.5
81.5
81
81
0.5
0.5
3.0
3.0
2
2
16.5
21.5
16.5
21.5
55.5
60.5
55
60
0.5
0.5
2.8
2.8
1
1
24.5
24.5
72.5
72
0.5
3.0
33.5
45.5
33.5
45.5
81.5
81.5
81
81
0.5
0.5
3.0
3.0
2
2
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N115
N119
Q001
DRILLING
(mm)
Stock
VP15TF
DC
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
N097
MZE/MZS
DC
(mm)
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
DRILLING
3.7
3.8
3.9
4.0
Stock
Dimensions (mm)
VP15TF
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
Order Number
Ext.
Ext.
Int.
5
12
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE0290SA
MZE0290MA
MZS0290MB
MZS0290LB
MZS0290XB
MZE0300SA
MZE0300MA
MZS0300MB
MZS0300LB
MZE0310SA
MZE0310MA
MZS0310MB
MZS0310LB
MZE0320SA
MZE0320MA
MZS0320MB
MZS0320LB
MZE0330SA
MZE0330MA
MZS0330MB
MZS0330LB
MZE0340SA
MZE0340MA
MZS0340MB
MZS0340LB
MZE0350SA
MZE0350MA
MZS0350MB
MZS0350LB
MZE0360SA
MZE0360MA
MZS0360MB
MZS0360LB
MZE0370SA
MZE0370MA
MZS0370MB
MZS0370LB
MZE0380SA
MZE0380MA
MZS0380MB
MZS0380LB
MZE0390SA
MZE0390MA
MZS0390MB
MZS0390LB
MZE0400SA
MZE0400MA
MZS0400MB
MZS0400LB
(l/d)
LH
OAL
LF
PL
DCON
16.5
16.5
55.5
55
0.5
2.9
21.5
21.5
60.5
60
0.5
2.9
24.5
24.5
72.5
72
0.5
3.0
33.5
45.5
33.5
45.5
81.5
81.5
81
81
0.5
0.5
3.0
3.0
2
2
16.5
21.5
16.5
21.5
55.5
60.5
55
60
0.5
0.5
3.0
3.0
1
1
24.5
33.5
24.5
33.5
72.5
81.5
72
81
0.5
0.5
3.0
3.0
2
2
18.6
24.6
18.6
24.6
55.6
60.6
55
60
0.6
0.6
3.1
3.1
1
1
28.6
39.6
28.6
39.6
76.6
87.6
76
87
0.6
0.6
4.0
4.0
2
2
18.6
24.6
18.6
24.6
55.6
60.6
55
60
0.6
0.6
3.2
3.2
1
1
28.6
39.6
28.6
39.6
76.6
87.6
76
87
0.6
0.6
4.0
4.0
2
2
18.6
24.6
18.6
24.6
55.6
60.6
55
60
0.6
0.6
3.3
3.3
1
1
28.6
39.6
28.6
39.6
76.6
87.6
76
87
0.6
0.6
4.0
4.0
2
2
20.6
24.6
20.6
24.6
55.6
60.6
55
60
0.6
0.6
3.4
3.4
1
1
28.6
39.6
28.6
39.6
76.6
87.6
76
87
0.6
0.6
4.0
4.0
2
2
20.6
24.6
20.6
24.6
55.6
60.6
55
60
0.6
0.6
3.5
3.5
1
1
28.6
39.6
28.6
39.6
76.6
87.6
76
87
0.6
0.6
4.0
4.0
2
2
20.7
27.7
20.7
27.7
55.7
60.7
55
60
0.7
0.7
3.6
3.6
1
1
32.7
44.7
32.7
44.7
80.7
92.7
80
92
0.7
0.7
4.0
4.0
2
2
20.7
27.7
20.7
27.7
55.7
60.7
55
60
0.7
0.7
3.7
3.7
1
1
32.7
44.7
32.7
44.7
80.7
92.7
80
92
0.7
0.7
4.0
4.0
2
2
22.7
27.7
22.7
27.7
55.7
60.7
55
60
0.7
0.7
3.8
3.8
1
1
32.7
44.7
32.7
44.7
80.7
92.7
80
92
0.7
0.7
4.0
4.0
2
2
22.7
27.7
22.7
27.7
55.7
60.7
55
60
0.7
0.7
3.9
3.9
1
1
32.7
44.7
32.7
44.7
80.7
92.7
80
92
0.7
0.7
4.0
4.0
2
2
22.7
27.7
22.7
27.7
55.7
60.7
55
60
0.7
0.7
4.0
4.0
1
1
32.7
44.7
32.7
44.7
80.7
92.7
80
92
0.7
0.7
4.0
4.0
2
2
N098
Type
LCF
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
5.1
5.2
Dimensions (mm)
Order Number
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE0410SA
MZE0410MA
MZS0410MB
MZS0410LB
MZE0420SA
MZE0420MA
MZS0420MB
MZS0420LB
MZE0430SA
MZE0430MA
MZS0430MB
MZS0430LB
MZE0440SA
MZE0440MA
MZS0440MB
MZS0440LB
MZE0450SA
MZE0450MA
MZS0450MB
MZS0450LB
MZE0460SA
MZE0460MA
MZS0460MB
MZS0460LB
MZE0470SA
MZE0470MA
MZS0470MB
MZS0470LB
MZE0480SA
MZE0480MA
MZS0480MB
MZS0480LB
MZE0490SA
MZE0490MA
MZS0490MB
MZS0490LB
MZE0500SA
MZE0500MA
MZS0500MB
MZS0500LB
MZE0510SA
MZE0510MA
MZS0510MB
MZS0510LB
MZE0520SA
MZE0520MA
MZS0520MB
MZS0520LB
(l/d)
Type
LCF
LH
OAL
LF
PL
DCON
22.7
22.7
55.7
55
0.7
4.1
29.7
29.7
63.7
63
0.7
4.1
36.7
50.7
36.7
50.7
86.7
100.7
86
100
0.7
0.7
5.0
5.0
2
2
22.8
29.8
22.8
29.8
55.8
63.8
55
63
0.8
0.8
4.2
4.2
1
1
36.8
50.8
36.8
50.8
86.8
100.8
86
100
0.8
0.8
5.0
5.0
2
2
24.8
29.8
24.8
29.8
58.8
63.8
58
63
0.8
0.8
4.3
4.3
1
1
36.8
50.8
36.8
50.8
86.8
100.8
86
100
0.8
0.8
5.0
5.0
2
2
24.8
29.8
24.8
29.8
58.8
63.8
58
63
0.8
0.8
4.4
4.4
1
1
36.8
50.8
36.8
50.8
86.8
100.8
86
100
0.8
0.8
5.0
5.0
2
2
24.8
29.8
24.8
29.8
58.8
63.8
58
63
0.8
0.8
4.5
4.5
1
1
36.8
50.8
36.8
50.8
86.8
100.8
86
100
0.8
0.8
5.0
5.0
2
2
24.8
32.8
24.8
32.8
58.8
68.8
58
68
0.8
0.8
4.6
4.6
1
1
40.8
55.8
40.8
55.8
90.8
105.8
90
105
0.8
0.8
5.0
5.0
2
2
24.9
32.9
24.9
32.9
58.9
68.9
58
68
0.9
0.9
4.7
4.7
1
1
40.9
55.9
40.9
55.9
90.9
105.9
90
105
0.9
0.9
5.0
5.0
2
2
26.9
32.9
26.9
32.9
62.9
68.9
62
68
0.9
0.9
4.8
4.8
1
1
40.9
55.9
40.9
55.9
90.9
105.9
90
105
0.9
0.9
5.0
5.0
2
2
26.9
32.9
26.9
32.9
62.9
68.9
62
68
0.9
0.9
4.9
4.9
1
1
40.9
55.9
40.9
55.9
90.9
105.9
90
105
0.9
0.9
5.0
5.0
2
2
26.9
32.9
26.9
32.9
62.9
68.9
62
68
0.9
0.9
5.0
5.0
1
1
28.4
44.9
30.9
48.9
82.9
100.9
82
100
0.9
0.9
6.0
6.0
2
2
26.9
34.9
26.9
34.9
62.9
72.9
62
72
0.9
0.9
5.1
5.1
1
1
28.4
44.9
30.9
48.9
82.9
100.9
82
100
0.9
0.9
6.0
6.0
2
2
26.9
34.9
26.9
34.9
62.9
72.9
62
72
0.9
0.9
5.2
5.2
1
1
28.4
44.9
30.9
48.9
82.9
100.9
82
100
0.9
0.9
6.0
6.0
2
2
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N115
N119
Q001
DRILLING
(mm)
Stock
VP15TF
DC
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
N099
MZE/MZS
DC
(mm)
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6.0
DRILLING
6.1
6.2
6.3
6.4
Stock
Dimensions (mm)
VP15TF
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE0530SA
MZE0530MA
MZS0530MB
MZS0530LB
MZE0540SA
MZE0540MA
MZS0540MB
MZS0540LB
MZE0550SA
MZE0550MA
MZS0550MB
MZS0550LB
MZE0560SA
MZE0560MA
MZS0560MB
MZS0560LB
MZE0570SA
MZE0570MA
MZS0570MB
MZS0570LB
MZE0580SA
MZE0580MA
MZS0580MB
MZS0580LB
MZE0590SA
MZE0590MA
MZS0590MB
MZS0590LB
MZE0600SA
MZE0600MA
MZS0600MB
MZS0600LB
MZE0610SA
MZE0610MA
MZS0610MB
MZS0610LB
MZE0620SA
MZE0620MA
MZS0620MB
MZS0620LB
MZE0630SA
MZE0630MA
MZS0630MB
MZS0630LB
MZE0640SA
MZE0640MA
MZS0640MB
MZS0640LB
(l/d)
LH
OAL
LF
PL
DCON
27.0
35.0
27.0
35.0
63.0
73.0
62
72
1.0
1.0
5.3
5.3
1
1
28.5
45.0
31.0
49.0
83.0
101.0
82
100
1.0
1.0
6.0
6.0
2
2
29.0
35.0
29.0
35.0
67.0
73.0
66
72
1.0
1.0
5.4
5.4
1
1
28.5
45.0
31.0
49.0
83.0
101.0
82
100
1.0
1.0
6.0
6.0
2
2
29.0
35.0
29.0
35.0
67.0
73.0
66
72
1.0
1.0
5.5
5.5
1
1
28.5
45.0
31.0
49.0
83.0
101.0
82
100
1.0
1.0
6.0
6.0
2
2
29.0
37.0
29.0
37.0
67.0
75.0
66
74
1.0
1.0
5.6
5.6
1
1
31.0
49.0
31.0
49.0
83.0
101.0
82
100
1.0
1.0
6.0
6.0
2
2
29.0
37.0
29.0
37.0
67.0
75.0
66
74
1.0
1.0
5.7
5.7
1
1
31.0
49.0
31.0
49.0
83.0
101.0
82
100
1.0
1.0
6.0
6.0
2
2
29.1
37.1
29.1
37.1
67.1
75.1
66
74
1.1
1.1
5.8
5.8
1
1
31.1
49.1
31.1
49.1
83.1
101.1
82
100
1.1
1.1
6.0
6.0
2
2
29.1
37.1
29.1
37.1
67.1
75.1
66
74
1.1
1.1
5.9
5.9
1
1
31.1
49.1
31.1
49.1
83.1
101.1
82
100
1.1
1.1
6.0
6.0
2
2
29.1
42.1
29.1
42.1
67.1
82.1
66
81
1.1
1.1
6.0
6.0
1
1
31.1
49.1
31.1
49.1
83.1
101.1
82
100
1.1
1.1
6.0
6.0
2
2
32.1
42.1
32.1
42.1
71.1
82.1
70
81
1.1
1.1
6.1
6.1
1
1
33.6
53.1
36.1
57.1
89.1
110.1
88
109
1.1
1.1
7.0
7.0
2
2
32.1
42.1
32.1
42.1
71.1
82.1
70
81
1.1
1.1
6.2
6.2
1
1
33.6
53.1
36.1
57.1
89.1
110.1
88
109
1.1
1.1
7.0
7.0
2
2
32.1
42.1
32.1
42.1
71.1
82.1
70
81
1.1
1.1
6.3
6.3
1
1
33.6
53.1
36.1
57.1
89.1
110.1
88
109
1.1
1.1
7.0
7.0
2
2
32.2
42.2
32.2
42.2
71.2
82.2
70
81
1.2
1.2
6.4
6.4
1
1
33.7
53.2
36.2
57.2
89.2
110.2
88
109
1.2
1.2
7.0
7.0
2
2
N100
Type
LCF
6.5
6.6
6.7
6.8
6.9
7.0
7.1
7.2
7.3
7.4
7.5
7.6
Dimensions (mm)
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE0650SA
MZE0650MA
MZS0650MB
MZS0650LB
MZE0660SA
MZE0660MA
MZS0660MB
MZS0660LB
MZE0670SA
MZE0670MA
MZS0670MB
MZS0670LB
MZE0680SA
MZE0680MA
MZS0680MB
MZS0680LB
MZE0690SA
MZE0690MA
MZS0690MB
MZS0690LB
MZE0700SA
MZE0700MA
MZS0700MB
MZS0700LB
MZE0710SA
MZE0710MA
MZS0710MB
MZS0710LB
MZE0720SA
MZE0720MA
MZS0720MB
MZS0720LB
MZE0730SA
MZE0730MA
MZS0730MB
MZS0730LB
MZE0740SA
MZE0740MA
MZS0740MB
MZS0740LB
MZE0750SA
MZE0750MA
MZS0750MB
MZS0750LB
MZE0760SA
MZE0760MA
MZS0760MB
MZS0760LB
(l/d)
Type
LCF
LH
OAL
LF
PL
DCON
32.2
42.2
32.2
42.2
71.2
82.2
70
81
1.2
1.2
6.5
6.5
1
1
33.7
53.2
36.2
57.2
89.2
110.2
88
109
1.2
1.2
7.0
7.0
2
2
32.2
44.2
32.2
44.2
71.2
84.2
70
83
1.2
1.2
6.6
6.6
1
1
36.2
57.2
36.2
57.2
89.2
110.2
88
109
1.2
1.2
7.0
7.0
2
2
32.2
44.2
32.2
44.2
71.2
84.2
70
83
1.2
1.2
6.7
6.7
1
1
36.2
57.2
36.2
57.2
89.2
110.2
88
109
1.2
1.2
7.0
7.0
2
2
35.2
44.2
35.2
44.2
75.2
84.2
74
83
1.2
1.2
6.8
6.8
1
1
36.2
57.2
36.2
57.2
89.2
110.2
88
109
1.2
1.2
7.0
7.0
2
2
35.3
44.3
35.3
44.3
75.3
84.3
74
83
1.3
1.3
6.9
6.9
1
1
36.3
57.3
36.3
57.3
89.3
110.3
88
109
1.3
1.3
7.0
7.0
2
2
35.3
44.3
35.3
44.3
75.3
84.3
74
83
1.3
1.3
7.0
7.0
1
1
36.3
57.3
36.3
57.3
89.3
110.3
88
109
1.3
1.3
7.0
7.0
2
2
35.3
46.3
35.3
46.3
75.3
88.3
74
87
1.3
1.3
7.1
7.1
1
1
38.8
61.3
41.3
65.3
95.3
119.3
94
118
1.3
1.3
8.0
8.0
2
2
35.3
46.3
35.3
46.3
75.3
88.3
74
87
1.3
1.3
7.2
7.2
1
1
38.8
61.3
41.3
65.3
95.3
119.3
94
118
1.3
1.3
8.0
8.0
2
2
35.3
46.3
35.3
46.3
75.3
88.3
74
87
1.3
1.3
7.3
7.3
1
1
38.8
61.3
41.3
65.3
95.3
119.3
94
118
1.3
1.3
8.0
8.0
2
2
35.3
46.3
35.3
46.3
75.3
88.3
74
87
1.3
1.3
7.4
7.4
1
1
38.8
61.3
41.3
65.3
95.3
119.3
94
118
1.3
1.3
8.0
8.0
2
2
35.4
46.4
35.4
46.4
75.4
88.4
74
87
1.4
1.4
7.5
7.5
1
1
38.9
61.4
41.4
65.4
95.4
119.4
94
118
1.4
1.4
8.0
8.0
2
2
38.4
49.4
38.4
49.4
80.4
91.4
79
90
1.4
1.4
7.6
7.6
1
1
41.4
65.4
41.4
65.4
95.4
119.4
94
118
1.4
1.4
8.0
8.0
2
2
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N115
N119
Q001
DRILLING
(mm)
Stock
VP15TF
DC
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
N101
MZE/MZS
DC
(mm)
7.7
7.8
7.9
8.0
8.1
8.2
8.3
8.4
DRILLING
8.5
8.6
8.7
8.8
Stock
Dimensions (mm)
VP15TF
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE0770SA
MZE0770MA
MZS0770MB
MZS0770LB
MZE0780SA
MZE0780MA
MZS0780MB
MZS0780LB
MZE0790SA
MZE0790MA
MZS0790MB
MZS0790LB
MZE0800SA
MZE0800MA
MZS0800MB
MZS0800LB
MZE0810SA
MZE0810MA
MZS0810MB
MZS0810LB
MZE0820SA
MZE0820MA
MZS0820MB
MZS0820LB
MZE0830SA
MZE0830MA
MZS0830MB
MZS0830LB
MZE0840SA
MZE0840MA
MZS0840MB
MZS0840LB
MZE0850SA
MZE0850MA
MZS0850MB
MZS0850LB
MZE0860SA
MZE0860MA
MZS0860MB
MZS0860LB
MZE0870SA
MZE0870MA
MZS0870MB
MZS0870LB
MZE0880SA
MZE0880MA
MZS0880MB
MZS0880LB
(l/d)
LH
OAL
LF
PL
DCON
38.4
49.4
38.4
49.4
80.4
91.4
79
90
1.4
1.4
7.7
7.7
1
1
41.4
65.4
41.4
65.4
95.4
119.4
94
118
1.4
1.4
8.0
8.0
2
2
38.4
49.4
38.4
49.4
80.4
91.4
79
90
1.4
1.4
7.8
7.8
1
1
41.4
65.4
41.4
65.4
95.4
119.4
94
118
1.4
1.4
8.0
8.0
2
2
38.4
49.4
38.4
49.4
80.4
91.4
79
90
1.4
1.4
7.9
7.9
1
1
41.4
65.4
41.4
65.4
95.4
119.4
94
118
1.4
1.4
8.0
8.0
2
2
38.5
49.5
38.5
49.5
80.5
91.5
79
90
1.5
1.5
8.0
8.0
1
1
41.5
65.5
41.5
65.5
95.5
119.5
94
118
1.5
1.5
8.0
8.0
2
2
38.5
54.5
38.5
54.5
80.5
97.5
79
96
1.5
1.5
8.1
8.1
1
1
44.0
69.5
46.5
73.5
101.5
128.5
100
127
1.5
1.5
9.0
9.0
2
2
38.5
54.5
38.5
54.5
80.5
97.5
79
96
1.5
1.5
8.2
8.2
1
1
44.0
69.5
46.5
73.5
101.5
128.5
100
127
1.5
1.5
9.0
9.0
2
2
38.5
54.5
38.5
54.5
80.5
97.5
79
96
1.5
1.5
8.3
8.3
1
1
44.0
69.5
46.5
73.5
101.5
128.5
100
127
1.5
1.5
9.0
9.0
2
2
38.5
54.5
38.5
54.5
80.5
97.5
79
96
1.5
1.5
8.4
8.4
1
1
44.0
69.5
46.5
73.5
101.5
128.5
100
127
1.5
1.5
9.0
9.0
2
2
38.5
54.5
38.5
54.5
80.5
97.5
79
96
1.5
1.5
8.5
8.5
1
1
44.0
69.5
46.5
73.5
101.5
128.5
100
127
1.5
1.5
9.0
9.0
2
2
41.6
56.6
41.6
56.6
85.6
99.6
84
98
1.6
1.6
8.6
8.6
1
1
46.6
73.6
46.6
73.6
101.6
128.6
100
127
1.6
1.6
9.0
9.0
2
2
41.6
56.6
41.6
56.6
85.6
99.6
84
98
1.6
1.6
8.7
8.7
1
1
46.6
73.6
46.6
73.6
101.6
128.6
100
127
1.6
1.6
9.0
9.0
2
2
41.6
56.6
41.6
56.6
85.6
99.6
84
98
1.6
1.6
8.8
8.8
1
1
46.6
73.6
46.6
73.6
101.6
128.6
100
127
1.6
1.6
9.0
9.0
2
2
N102
Type
LCF
8.9
9.0
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
10.0
Dimensions (mm)
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE0890SA
MZE0890MA
MZS0890MB
MZS0890LB
MZE0900SA
MZE0900MA
MZS0900MB
MZS0900LB
MZE0910SA
MZE0910MA
MZS0910MB
MZS0910LB
MZE0920SA
MZE0920MA
MZS0920MB
MZS0920LB
MZE0930SA
MZE0930MA
MZS0930MB
MZS0930LB
MZE0940SA
MZE0940MA
MZS0940MB
MZS0940LB
MZE0950SA
MZE0950MA
MZS0950MB
MZS0950LB
MZE0960SA
MZE0960MA
MZS0960MB
MZS0960LB
MZE0970SA
MZE0970MA
MZS0970MB
MZS0970LB
MZE0980SA
MZE0980MA
MZS0980MB
MZS0980LB
MZE0990SA
MZE0990MA
MZS0990MB
MZS0990LB
MZE1000SA
MZE1000MA
MZS1000MB
MZS1000LB
(l/d)
LH
OAL
LF
PL
41.6
56.6
41.6
56.6
85.6
99.6
84
98
1.6
1.6
8.9
8.9
1
1
46.6
73.6
46.6
73.6
101.6
128.6
100
127
1.6
1.6
9.0
9.0
2
2
41.6
56.6
41.6
56.6
85.6
99.6
84
98
1.6
1.6
9.0
9.0
1
1
46.6
73.6
46.6
73.6
101.6
128.6
100
127
1.6
1.6
9.0
9.0
2
2
41.7
59.7
41.7
59.7
85.7
103.7
84
102
1.7
1.7
9.1
9.1
1
1
49.2
77.7
51.7
81.7
107.7
137.7
106
136
1.7
1.7
10.0
10.0
2
2
41.7
59.7
41.7
59.7
85.7
103.7
84
102
1.7
1.7
9.2
9.2
1
1
49.2
77.7
51.7
81.7
107.7
137.7
106
136
1.7
1.7
10.0
10.0
2
2
41.7
59.7
41.7
59.7
85.7
103.7
84
102
1.7
1.7
9.3
9.3
1
1
49.2
77.7
51.7
81.7
107.7
137.7
106
136
1.7
1.7
10.0
10.0
2
2
41.7
59.7
41.7
59.7
85.7
103.7
84
102
1.7
1.7
9.4
9.4
1
1
49.2
77.7
51.7
81.7
107.7
137.7
106
136
1.7
1.7
10.0
10.0
2
2
41.7
59.7
41.7
59.7
85.7
103.7
84
102
1.7
1.7
9.5
9.5
1
1
49.2
77.7
51.7
81.7
107.7
137.7
106
136
1.7
1.7
10.0
10.0
2
2
44.7
61.7
44.7
61.7
90.7
106.7
89
105
1.7
1.7
9.6
9.6
1
1
51.7
81.7
51.7
81.7
107.7
137.7
106
136
1.7
1.7
10.0
10.0
2
2
44.8
61.8
44.8
61.8
90.8
106.8
89
105
1.8
1.8
9.7
9.7
1
1
51.8
81.8
51.8
81.8
107.8
137.8
106
136
1.8
1.8
10.0
10.0
2
2
44.8
61.8
44.8
61.8
90.8
106.8
89
105
1.8
1.8
9.8
9.8
1
1
51.8
81.8
51.8
81.8
107.8
137.8
106
136
1.8
1.8
10.0
10.0
2
2
44.8
61.8
44.8
61.8
90.8
106.8
89
105
1.8
1.8
9.9
9.9
1
1
51.8
81.8
51.8
81.8
107.8
137.8
106
136
1.8
1.8
10.0
10.0
2
2
44.8
61.8
44.8
61.8
90.8
106.8
89
105
1.8
1.8
10.0
10.0
1
1
51.8
81.8
51.8
81.8
107.8
137.8
106
136
1.8
1.8
10.0
10.0
2
2
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
DCON
Type
LCF
N115
N119
Q001
DRILLING
(mm)
Stock
VP15TF
DC
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
N103
MZE/MZS
(mm)
10.1
10.2
10.3
10.4
10.5
10.6
10.7
10.8
DRILLING
10.9
11.0
11.1
11.2
Stock
Dimensions (mm)
VP15TF
DC
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE1010SA
MZE1010MA
MZS1010MB
MZS1010LB
MZE1020SA
MZE1020MA
MZS1020MB
MZS1020LB
MZE1030SA
MZE1030MA
MZS1030MB
MZS1030LB
MZE1040SA
MZE1040MA
MZS1040MB
MZS1040LB
MZE1050SA
MZE1050MA
MZS1050MB
MZS1050LB
MZE1060SA
MZE1060MA
MZS1060MB
MZS1060LB
MZE1070SA
MZE1070MA
MZS1070MB
MZS1070LB
MZE1080SA
MZE1080MA
MZS1080MB
MZS1080LB
MZE1090SA
MZE1090MA
MZS1090MB
MZS1090LB
MZE1100SA
MZE1100MA
MZS1100MB
MZS1100LB
MZE1110SA
MZE1110MA
MZS1110MB
MZS1110LB
MZE1120SA
MZE1120MA
MZS1120MB
MZS1120LB
(l/d)
LH
OAL
LF
PL
DCON
44.8
67.8
44.8
67.8
90.8
113.8
89
112
1.8
1.8
10.1
10.1
1
1
54.3
85.8
56.8
89.8
117.8
150.8
116
149
1.8
1.8
11.0
11.0
2
2
44.9
67.9
44.9
67.9
90.9
113.9
89
112
1.9
1.9
10.2
10.2
1
1
54.4
85.9
56.9
89.9
117.9
150.9
116
149
1.9
1.9
11.0
11.0
2
2
44.9
67.9
44.9
67.9
90.9
113.9
89
112
1.9
1.9
10.3
10.3
1
1
54.4
85.9
56.9
89.9
117.9
150.9
116
149
1.9
1.9
11.0
11.0
2
2
44.9
67.9
44.9
67.9
90.9
113.9
89
112
1.9
1.9
10.4
10.4
1
1
54.4
85.9
56.9
89.9
117.9
150.9
116
149
1.9
1.9
11.0
11.0
2
2
44.9
67.9
44.9
67.9
90.9
113.9
89
112
1.9
1.9
10.5
10.5
1
1
54.4
85.9
56.9
89.9
117.9
150.9
116
149
1.9
1.9
11.0
11.0
2
2
44.9
69.9
44.9
69.9
90.9
115.9
89
114
1.9
1.9
10.6
10.6
1
1
56.9
89.9
56.9
89.9
117.9
150.9
116
149
1.9
1.9
11.0
11.0
2
2
48.9
69.9
48.9
69.9
96.9
115.9
95
114
1.9
1.9
10.7
10.7
1
1
56.9
89.9
56.9
89.9
117.9
150.9
116
149
1.9
1.9
11.0
11.0
2
2
49.0
70.0
49.0
70.0
97.0
116.0
95
114
2.0
2.0
10.8
10.8
1
1
57.0
90.0
57.0
90.0
118.0
151.0
116
149
2.0
2.0
11.0
11.0
2
2
49.0
70.0
49.0
70.0
97.0
116.0
95
114
2.0
2.0
10.9
10.9
1
1
57.0
90.0
57.0
90.0
118.0
151.0
116
149
2.0
2.0
11.0
11.0
2
2
49.0
70.0
49.0
70.0
97.0
116.0
95
114
2.0
2.0
11.0
11.0
1
1
57.0
90.0
57.0
90.0
118.0
151.0
116
149
2.0
2.0
11.0
11.0
2
2
49.0
73.0
49.0
73.0
97.0
120.0
95
118
2.0
2.0
11.1
11.1
1
1
59.5
94.0
62.0
98.0
124.0
160.0
122
158
2.0
2.0
12.0
12.0
2
2
49.0
73.0
49.0
73.0
97.0
120.0
95
118
2.0
2.0
11.2
11.2
1
1
59.5
94.0
62.0
98.0
124.0
160.0
122
158
2.0
2.0
12.0
12.0
2
2
N104
Type
LCF
11.3
11.4
11.5
11.6
11.7
11.8
11.9
12.0
12.1
12.2
12.3
12.4
Dimensions (mm)
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE1130SA
MZE1130MA
MZS1130MB
MZS1130LB
MZE1140SA
MZE1140MA
MZS1140MB
MZS1140LB
MZE1150SA
MZE1150MA
MZS1150MB
MZS1150LB
MZE1160SA
MZE1160MA
MZS1160MB
MZS1160LB
MZE1170SA
MZE1170MA
MZS1170MB
MZS1170LB
MZE1180SA
MZE1180MA
MZS1180MB
MZS1180LB
MZE1190SA
MZE1190MA
MZS1190MB
MZS1190LB
MZE1200SA
MZE1200MA
MZS1200MB
MZS1200LB
MZE1210SA
MZE1210MA
MZS1210MB
MZS1210LB
MZE1220SA
MZE1220MA
MZS1220MB
MZS1220LB
MZE1230SA
MZE1230MA
MZS1230MB
MZS1230LB
MZE1240SA
MZE1240MA
MZS1240MB
MZS1240LB
(l/d)
Type
LCF
LH
OAL
LF
PL
DCON
49.1
73.1
49.1
73.1
97.1
120.1
95
118
2.1
2.1
11.3
11.3
1
1
59.6
94.1
62.1
98.1
124.1
160.1
122
158
2.1
2.1
12.0
12.0
2
2
49.1
73.1
49.1
73.1
97.1
120.1
95
118
2.1
2.1
11.4
11.4
1
1
59.6
94.1
62.1
98.1
124.1
160.1
122
158
2.1
2.1
12.0
12.0
2
2
49.1
73.1
49.1
73.1
97.1
120.1
95
118
2.1
2.1
11.5
11.5
1
1
59.6
94.1
62.1
98.1
124.1
160.1
122
158
2.1
2.1
12.0
12.0
2
2
49.1
75.1
49.1
75.1
97.1
123.1
95
121
2.1
2.1
11.6
11.6
1
1
62.1
98.1
62.1
98.1
124.1
160.1
122
158
2.1
2.1
12.0
12.0
2
2
49.1
75.1
49.1
75.1
97.1
123.1
95
121
2.1
2.1
11.7
11.7
1
1
62.1
98.1
62.1
98.1
124.1
160.1
122
158
2.1
2.1
12.0
12.0
2
2
49.1
75.1
49.1
75.1
97.1
123.1
95
121
2.1
2.1
11.8
11.8
1
1
62.1
98.1
62.1
98.1
124.1
160.1
122
158
2.1
2.1
12.0
12.0
2
2
53.2
75.2
53.2
75.2
104.2
123.2
102
121
2.2
2.2
11.9
11.9
1
1
62.2
98.2
62.2
98.2
124.2
160.2
122
158
2.2
2.2
12.0
12.0
2
2
53.2
75.2
53.2
75.2
104.2
123.2
102
121
2.2
2.2
12.0
12.0
1
1
62.2
98.2
62.2
98.2
124.2
160.2
122
158
2.2
2.2
12.0
12.0
2
2
53.2
78.2
53.2
78.2
104.2
137.2
102
135
2.2
2.2
12.1
12.1
1
1
64.7
102.2
67.2
106.2
130.2
169.2
128
167
2.2
2.2
13.0
13.0
2
2
53.2
78.2
53.2
78.2
104.2
137.2
102
135
2.2
2.2
12.2
12.2
1
1
64.7
102.2
67.2
106.2
130.2
169.2
128
167
2.2
2.2
13.0
13.0
2
2
53.2
78.2
53.2
78.2
104.2
137.2
102
135
2.2
2.2
12.3
12.3
1
1
64.7
102.2
67.2
106.2
130.2
169.2
128
167
2.2
2.2
13.0
13.0
2
2
53.3
78.3
53.3
78.3
104.3
137.3
102
135
2.3
2.3
12.4
12.4
1
1
64.8
102.3
67.3
106.3
130.3
169.3
128
167
2.3
2.3
13.0
13.0
2
2
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N115
N119
Q001
DRILLING
(mm)
Stock
VP15TF
DC
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
N105
MZE/MZS
DC
(mm)
12.5
12.6
12.7
12.8
12.9
13.0
13.1
13.2
DRILLING
13.3
13.4
13.5
13.6
Stock
Dimensions (mm)
VP15TF
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE1250SA
MZE1250MA
MZS1250MB
MZS1250LB
MZE1260SA
MZE1260MA
MZS1260MB
MZS1260LB
MZE1270SA
MZE1270MA
MZS1270MB
MZS1270LB
MZE1280SA
MZE1280MA
MZS1280MB
MZS1280LB
MZE1290SA
MZE1290MA
MZS1290MB
MZS1290LB
MZE1300SA
MZE1300MA
MZS1300MB
MZS1300LB
MZE1310SA
MZE1310MA
MZS1310MB
MZS1310LB
MZE1320SA
MZE1320MA
MZS1320MB
MZS1320LB
MZE1330SA
MZE1330MA
MZS1330MB
MZS1330LB
MZE1340SA
MZE1340MA
MZS1340MB
MZS1340LB
MZE1350SA
MZE1350MA
MZS1350MB
MZS1350LB
MZE1360SA
MZE1360MA
MZS1360MB
MZS1360LB
(l/d)
LH
OAL
LF
PL
DCON
53.3
78.3
53.3
78.3
104.3
137.3
102
135
2.3
2.3
12.5
12.5
1
1
64.8
102.3
67.3
106.3
130.3
169.3
128
167
2.3
2.3
13.0
13.0
2
2
53.3
80.3
53.3
80.3
104.3
139.3
102
137
2.3
2.3
12.6
12.6
1
1
67.3
106.3
67.3
106.3
130.3
169.3
128
167
2.3
2.3
13.0
13.0
2
2
53.3
80.3
53.3
80.3
104.3
139.3
102
137
2.3
2.3
12.7
12.7
1
1
67.3
106.3
67.3
106.3
130.3
169.3
128
167
2.3
2.3
13.0
13.0
2
2
53.3
80.3
53.3
80.3
104.3
139.3
102
137
2.3
2.3
12.8
12.8
1
1
67.3
106.3
67.3
106.3
130.3
169.3
128
167
2.3
2.3
13.0
13.0
2
2
53.3
80.3
53.3
80.3
104.3
139.3
102
137
2.3
2.3
12.9
12.9
1
1
67.3
106.3
67.3
106.3
130.3
169.3
128
167
2.3
2.3
13.0
13.0
2
2
53.4
80.4
53.4
80.4
104.4
139.4
102
137
2.4
2.4
13.0
13.0
1
1
67.4
106.4
67.4
106.4
130.4
169.4
128
167
2.4
2.4
13.0
13.0
2
2
53.4
86.4
53.4
86.4
104.4
146.4
102
144
2.4
2.4
13.1
13.1
1
1
69.9
110.4
72.4
114.4
136.4
178.4
134
176
2.4
2.4
14.0
14.0
2
2
53.4
86.4
53.4
86.4
104.4
146.4
102
144
2.4
2.4
13.2
13.2
1
1
69.9
110.4
72.4
114.4
136.4
178.4
134
176
2.4
2.4
14.0
14.0
2
2
56.4
86.4
56.4
86.4
109.4
146.4
107
144
2.4
2.4
13.3
13.3
1
1
69.9
110.4
72.4
114.4
136.4
178.4
134
176
2.4
2.4
14.0
14.0
2
2
56.4
86.4
56.4
86.4
109.4
146.4
107
144
2.4
2.4
13.4
13.4
1
1
69.9
110.4
72.4
114.4
136.4
178.4
134
176
2.4
2.4
14.0
14.0
2
2
56.5
86.5
56.5
86.5
109.5
146.5
107
144
2.5
2.5
13.5
13.5
1
1
70.0
110.5
72.5
114.5
136.5
178.5
134
176
2.5
2.5
14.0
14.0
2
2
56.5
88.5
56.5
88.5
109.5
149.5
107
147
2.5
2.5
13.6
13.6
1
1
72.5
114.5
72.5
114.5
136.5
178.5
134
176
2.5
2.5
14.0
14.0
2
2
N106
Type
LCF
13.7
13.8
13.9
14.0
14.1
14.2
14.3
14.4
14.5
14.6
14.7
14.8
Dimensions (mm)
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE1370SA
MZE1370MA
MZS1370MB
MZS1370LB
MZE1380SA
MZE1380MA
MZS1380MB
MZS1380LB
MZE1390SA
MZE1390MA
MZS1390MB
MZS1390LB
MZE1400SA
MZE1400MA
MZS1400MB
MZS1400LB
MZE1410SA
MZE1410MA
MZS1410MB
MZS1410LB
MZE1420SA
MZE1420MA
MZS1420MB
MZS1420LB
MZE1430SA
MZE1430MA
MZS1430MB
MZS1430LB
MZE1440SA
MZE1440MA
MZS1440MB
MZS1440LB
MZE1450SA
MZE1450MA
MZS1450MB
MZS1450LB
MZE1460SA
MZE1460MA
MZS1460MB
MZS1460LB
MZE1470SA
MZE1470MA
MZS1470MB
MZS1470LB
MZE1480SA
MZE1480MA
MZS1480MB
MZS1480LB
(l/d)
Type
LCF
LH
OAL
LF
PL
DCON
56.5
88.5
56.5
88.5
109.5
149.5
107
147
2.5
2.5
13.7
13.7
1
1
72.5
114.5
72.5
114.5
136.5
178.5
134
176
2.5
2.5
14.0
14.0
2
2
56.5
88.5
56.5
88.5
109.5
149.5
107
147
2.5
2.5
13.8
13.8
1
1
72.5
114.5
72.5
114.5
136.5
178.5
134
176
2.5
2.5
14.0
14.0
2
2
56.5
88.5
56.5
88.5
109.5
149.5
107
147
2.5
2.5
13.9
13.9
1
1
72.5
114.5
72.5
114.5
136.5
178.5
134
176
2.5
2.5
14.0
14.0
2
2
56.5
88.5
56.5
88.5
109.5
149.5
107
147
2.5
2.5
14.0
14.0
1
1
72.5
114.5
72.5
114.5
136.5
178.5
134
176
2.5
2.5
14.0
14.0
2
2
58.6
91.6
58.6
91.6
113.6
153.6
111
151
2.6
2.6
14.1
14.1
1
1
75.1
118.6
77.6
122.6
142.6
187.6
140
185
2.6
2.6
15.0
15.0
2
2
58.6
91.6
58.6
91.6
113.6
153.6
111
151
2.6
2.6
14.2
14.2
1
1
75.1
118.6
77.6
122.6
142.6
187.6
140
185
2.6
2.6
15.0
15.0
2
2
58.6
91.6
58.6
91.6
113.6
153.6
111
151
2.6
2.6
14.3
14.3
1
1
75.1
118.6
77.6
122.6
142.6
187.6
140
185
2.6
2.6
15.0
15.0
2
2
58.6
91.6
58.6
91.6
113.6
153.6
111
151
2.6
2.6
14.4
14.4
1
1
75.1
118.6
77.6
122.6
142.6
187.6
140
185
2.6
2.6
15.0
15.0
2
2
58.6
91.6
58.6
91.6
113.6
153.6
111
151
2.6
2.6
14.5
14.5
1
1
75.1
118.6
77.6
122.6
142.6
187.6
140
185
2.6
2.6
15.0
15.0
2
2
58.7
93.7
58.7
93.7
113.7
155.7
111
153
2.7
2.7
14.6
14.6
1
1
77.7
122.7
77.7
122.7
142.7
187.7
140
185
2.7
2.7
15.0
15.0
2
2
58.7
93.7
58.7
93.7
113.7
155.7
111
153
2.7
2.7
14.7
14.7
1
1
77.7
122.7
77.7
122.7
142.7
187.7
140
185
2.7
2.7
15.0
15.0
2
2
58.7
93.7
58.7
93.7
113.7
155.7
111
153
2.7
2.7
14.8
14.8
1
1
77.7
122.7
77.7
122.7
142.7
187.7
140
185
2.7
2.7
15.0
15.0
2
2
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N115
N119
Q001
DRILLING
(mm)
Stock
VP15TF
DC
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
N107
MZE/MZS
DC
(mm)
14.9
15.0
15.1
15.2
15.3
15.4
15.5
15.6
DRILLING
15.7
15.8
15.9
16.0
Stock
Dimensions (mm)
VP15TF
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE1490SA
MZE1490MA
MZS1490MB
MZS1490LB
MZE1500SA
MZE1500MA
MZS1500MB
MZS1500LB
MZE1510SA
MZE1510MA
MZS1510MB
MZS1510LB
MZE1520SA
MZE1520MA
MZS1520MB
MZS1520LB
MZE1530SA
MZE1530MA
MZS1530MB
MZS1530LB
MZE1540SA
MZE1540MA
MZS1540MB
MZS1540LB
MZE1550SA
MZE1550MA
MZS1550MB
MZS1550LB
MZE1560SA
MZE1560MA
MZS1560MB
MZS1560LB
MZE1570SA
MZE1570MA
MZS1570MB
MZS1570LB
MZE1580SA
MZE1580MA
MZS1580MB
MZS1580LB
MZE1590SA
MZE1590MA
MZS1590MB
MZS1590LB
MZE1600SA
MZE1600MA
MZS1600MB
MZS1600LB
(l/d)
LH
OAL
LF
PL
DCON
58.7
93.7
58.7
93.7
113.7
155.7
111
153
2.7
2.7
14.9
14.9
1
1
77.7
122.7
77.7
122.7
142.7
187.7
140
185
2.7
2.7
15.0
15.0
2
2
58.7
93.7
58.7
93.7
113.7
155.7
111
153
2.7
2.7
15.0
15.0
1
1
77.7
122.7
77.7
122.7
142.7
187.7
140
185
2.7
2.7
15.0
15.0
2
2
60.7
96.7
60.7
96.7
117.7
159.7
115
157
2.7
2.7
15.1
15.1
1
1
80.2
126.7
82.7
130.7
147.7
195.7
145
193
2.7
2.7
16.0
16.0
2
2
60.8
96.8
60.8
96.8
117.8
159.8
115
157
2.8
2.8
15.2
15.2
1
1
80.3
126.8
82.8
130.8
147.8
195.8
145
193
2.8
2.8
16.0
16.0
2
2
60.8
96.8
60.8
96.8
117.8
159.8
115
157
2.8
2.8
15.3
15.3
1
1
80.3
126.8
82.8
130.8
147.8
195.8
145
193
2.8
2.8
16.0
16.0
2
2
60.8
96.8
60.8
96.8
117.8
159.8
115
157
2.8
2.8
15.4
15.4
1
1
80.3
126.8
82.8
130.8
147.8
195.8
145
193
2.8
2.8
16.0
16.0
2
2
60.8
96.8
60.8
96.8
117.8
159.8
115
157
2.8
2.8
15.5
15.5
1
1
80.3
126.8
82.8
130.8
147.8
195.8
145
193
2.8
2.8
16.0
16.0
2
2
60.8
98.8
60.8
98.8
117.8
162.8
115
160
2.8
2.8
15.6
15.6
1
1
82.8
130.8
82.8
130.8
147.8
195.8
145
193
2.8
2.8
16.0
16.0
2
2
60.9
98.9
60.9
98.9
117.9
162.9
115
160
2.9
2.9
15.7
15.7
1
1
82.9
130.9
82.9
130.9
147.9
195.9
145
193
2.9
2.9
16.0
16.0
2
2
60.9
98.9
60.9
98.9
117.9
162.9
115
160
2.9
2.9
15.8
15.8
1
1
82.9
130.9
82.9
130.9
147.9
195.9
145
193
2.9
2.9
16.0
16.0
2
2
60.9
98.9
60.9
98.9
117.9
162.9
115
160
2.9
2.9
15.9
15.9
1
1
82.9
130.9
82.9
130.9
147.9
195.9
145
193
2.9
2.9
16.0
16.0
2
2
60.9
98.9
60.9
98.9
117.9
162.9
115
160
2.9
2.9
16.0
16.0
1
1
82.9
130.9
82.9
130.9
147.9
195.9
145
193
2.9
2.9
16.0
16.0
2
2
N108
Type
LCF
16.1
16.2
16.3
16.4
16.5
16.6
16.7
16.8
16.9
17.0
17.1
17.2
Dimensions (mm)
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE1610SA
MZE1610MA
MZS1610MB
MZS1610LB
MZE1620SA
MZE1620MA
MZS1620MB
MZS1620LB
MZE1630SA
MZE1630MA
MZS1630MB
MZS1630LB
MZE1640SA
MZE1640MA
MZS1640MB
MZS1640LB
MZE1650SA
MZE1650MA
MZS1650MB
MZS1650LB
MZE1660SA
MZE1660MA
MZS1660MB
MZS1660LB
MZE1670SA
MZE1670MA
MZS1670MB
MZS1670LB
MZE1680SA
MZE1680MA
MZS1680MB
MZS1680LB
MZE1690SA
MZE1690MA
MZS1690MB
MZS1690LB
MZE1700SA
MZE1700MA
MZS1700MB
MZS1700LB
MZE1710SA
MZE1710MA
MZS1710MB
MZS1710LB
MZE1720SA
MZE1720MA
MZS1720MB
MZS1720LB
(l/d)
Type
LCF
LH
OAL
LF
PL
DCON
62.9
104.9
62.9
104.9
121.9
169.9
119
167
2.9
2.9
16.1
16.1
1
1
85.4
134.9
87.9
138.9
152.9
203.9
150
201
2.9
2.9
17.0
17.0
2
2
62.9
104.9
62.9
104.9
121.9
169.9
119
167
2.9
2.9
16.2
16.2
1
1
85.4
134.9
87.9
138.9
152.9
203.9
150
201
2.9
2.9
17.0
17.0
2
2
63.0
105.0
63.0
105.0
122.0
170.0
119
167
3.0
3.0
16.3
16.3
1
1
85.5
135.0
88.0
139.0
153.0
204.0
150
201
3.0
3.0
17.0
17.0
2
2
63.0
105.0
63.0
105.0
122.0
170.0
119
167
3.0
3.0
16.4
16.4
1
1
85.5
135.0
88.0
139.0
153.0
204.0
150
201
3.0
3.0
17.0
17.0
2
2
63.0
105.0
63.0
105.0
122.0
170.0
119
167
3.0
3.0
16.5
16.5
1
1
85.5
135.0
88.0
139.0
153.0
204.0
150
201
3.0
3.0
17.0
17.0
2
2
63.0
105.0
63.0
105.0
122.0
170.0
119
167
3.0
3.0
16.6
16.6
1
1
88.0
139.0
88.0
139.0
153.0
204.0
150
201
3.0
3.0
17.0
17.0
2
2
63.0
105.0
63.0
105.0
122.0
170.0
119
167
3.0
3.0
16.7
16.7
1
1
88.0
139.0
88.0
139.0
153.0
204.0
150
201
3.0
3.0
17.0
17.0
2
2
63.1
105.1
63.1
105.1
122.1
170.1
119
167
3.1
3.1
16.8
16.8
1
1
88.1
139.1
88.1
139.1
153.1
204.1
150
201
3.1
3.1
17.0
17.0
2
2
63.1
105.1
63.1
105.1
122.1
170.1
119
167
3.1
3.1
16.9
16.9
1
1
88.1
139.1
88.1
139.1
153.1
204.1
150
201
3.1
3.1
17.0
17.0
2
2
63.1
105.1
63.1
105.1
122.1
170.1
119
167
3.1
3.1
17.0
17.0
1
1
88.1
139.1
88.1
139.1
153.1
204.1
150
201
3.1
3.1
17.0
17.0
2
2
65.1
105.1
65.1
105.1
126.1
170.1
123
167
3.1
3.1
17.1
17.1
1
1
90.6
143.1
93.1
147.1
158.1
212.1
155
209
3.1
3.1
18.0
18.0
2
2
65.1
105.1
65.1
105.1
126.1
170.1
123
167
3.1
3.1
17.2
17.2
1
1
90.6
143.1
93.1
147.1
158.1
212.1
155
209
3.1
3.1
18.0
18.0
2
2
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N115
N119
Q001
DRILLING
(mm)
Stock
VP15TF
DC
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
N109
MZE/MZS
DC
(mm)
17.3
17.4
17.5
17.6
17.7
17.8
17.9
18.0
DRILLING
18.1
18.2
18.3
18.4
Stock
Dimensions (mm)
VP15TF
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE1730SA
MZE1730MA
MZS1730MB
MZS1730LB
MZE1740SA
MZE1740MA
MZS1740MB
MZS1740LB
MZE1750SA
MZE1750MA
MZS1750MB
MZS1750LB
MZE1760SA
MZE1760MA
MZS1760MB
MZS1760LB
MZE1770SA
MZE1770MA
MZS1770MB
MZS1770LB
MZE1780SA
MZE1780MA
MZS1780MB
MZS1780LB
MZE1790SA
MZE1790MA
MZS1790MB
MZS1790LB
MZE1800SA
MZE1800MA
MZS1800MB
MZS1800LB
MZE1810SA
MZE1810MA
MZS1810MB
MZS1810LB
MZE1820SA
MZE1820MA
MZS1820MB
MZS1820LB
MZE1830SA
MZE1830MA
MZS1830MB
MZS1830LB
MZE1840SA
MZE1840MA
MZS1840MB
MZS1840LB
(l/d)
LH
OAL
LF
PL
DCON
65.1
105.1
65.1
105.1
126.1
170.1
123
167
3.1
3.1
17.3
17.3
1
1
90.6
143.1
93.1
147.1
158.1
212.1
155
209
3.1
3.1
18.0
18.0
2
2
65.2
105.2
65.2
105.2
126.2
170.2
123
167
3.2
3.2
17.4
17.4
1
1
90.7
143.2
93.2
147.2
158.2
212.2
155
209
3.2
3.2
18.0
18.0
2
2
65.2
105.2
65.2
105.2
126.2
170.2
123
167
3.2
3.2
17.5
17.5
1
1
90.7
143.2
93.2
147.2
158.2
212.2
155
209
3.2
3.2
18.0
18.0
2
2
65.2
105.2
65.2
105.2
126.2
170.2
123
167
3.2
3.2
17.6
17.6
1
1
93.2
147.2
93.2
147.2
158.2
212.2
155
209
3.2
3.2
18.0
18.0
2
2
65.2
105.2
65.2
105.2
126.2
170.2
123
167
3.2
3.2
17.7
17.7
1
1
93.2
147.2
93.2
147.2
158.2
212.2
155
209
3.2
3.2
18.0
18.0
2
2
65.2
105.2
65.2
105.2
126.2
170.2
123
167
3.2
3.2
17.8
17.8
1
1
93.2
147.2
93.2
147.2
158.2
212.2
155
209
3.2
3.2
18.0
18.0
2
2
65.3
105.3
65.3
105.3
126.3
170.3
123
167
3.3
3.3
17.9
17.9
1
1
93.3
147.3
93.3
147.3
158.3
212.3
155
209
3.3
3.3
18.0
18.0
2
2
65.3
105.3
65.3
105.3
126.3
170.3
123
167
3.3
3.3
18.0
18.0
1
1
93.3
147.3
93.3
147.3
158.3
212.3
155
209
3.3
3.3
18.0
18.0
2
2
67.3
117.3
67.3
117.3
130.3
182.3
127
179
3.3
3.3
18.1
18.1
1
1
95.8
151.3
98.3
155.3
163.3
220.3
160
217
3.3
3.3
19.0
19.0
2
2
67.3
117.3
67.3
117.3
130.3
182.3
127
179
3.3
3.3
18.2
18.2
1
1
95.8
151.3
98.3
155.3
163.3
220.3
160
217
3.3
3.3
19.0
19.0
2
2
67.3
117.3
67.3
117.3
130.3
182.3
127
179
3.3
3.3
18.3
18.3
1
1
95.8
151.3
98.3
155.3
163.3
220.3
160
217
3.3
3.3
19.0
19.0
2
2
67.3
117.3
67.3
117.3
130.3
182.3
127
179
3.3
3.3
18.4
18.4
1
1
95.8
151.3
98.3
155.3
163.3
220.3
160
217
3.3
3.3
19.0
19.0
2
2
N110
Type
LCF
18.5
18.6
18.7
18.8
18.9
19.0
19.1
19.2
19.3
19.4
19.5
19.6
Dimensions (mm)
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE1850SA
MZE1850MA
MZS1850MB
MZS1850LB
MZE1860SA
MZE1860MA
MZS1860MB
MZS1860LB
MZE1870SA
MZE1870MA
MZS1870MB
MZS1870LB
MZE1880SA
MZE1880MA
MZS1880MB
MZS1880LB
MZE1890SA
MZE1890MA
MZS1890MB
MZS1890LB
MZE1900SA
MZE1900MA
MZS1900MB
MZS1900LB
MZE1910SA
MZE1910MA
MZS1910MB
MZS1910LB
MZE1920SA
MZE1920MA
MZS1920MB
MZS1920LB
MZE1930SA
MZE1930MA
MZS1930MB
MZS1930LB
MZE1940SA
MZE1940MA
MZS1940MB
MZS1940LB
MZE1950SA
MZE1950MA
MZS1950MB
MZS1950LB
MZE1960SA
MZE1960MA
MZS1960MB
MZS1960LB
(l/d)
Type
LCF
LH
OAL
LF
PL
DCON
67.4
117.4
67.4
117.4
130.4
182.4
127
179
3.4
3.4
18.5
18.5
1
1
95.9
151.4
98.4
155.4
163.4
220.4
160
217
3.4
3.4
19.0
19.0
2
2
67.4
117.4
67.4
117.4
130.4
182.4
127
179
3.4
3.4
18.6
18.6
1
1
98.4
155.4
98.4
155.4
163.4
220.4
160
217
3.4
3.4
19.0
19.0
2
2
67.4
117.4
67.4
117.4
130.4
182.4
127
179
3.4
3.4
18.7
18.7
1
1
98.4
155.4
98.4
155.4
163.4
220.4
160
217
3.4
3.4
19.0
19.0
2
2
67.4
117.4
67.4
117.4
130.4
182.4
127
179
3.4
3.4
18.8
18.8
1
1
98.4
155.4
98.4
155.4
163.4
220.4
160
217
3.4
3.4
19.0
19.0
2
2
67.4
117.4
67.4
117.4
130.4
182.4
127
179
3.4
3.4
18.9
18.9
1
1
98.4
155.4
98.4
155.4
163.4
220.4
160
217
3.4
3.4
19.0
19.0
2
2
67.5
117.5
67.5
117.5
130.5
182.5
127
179
3.5
3.5
19.0
19.0
1
1
98.5
155.5
98.5
155.5
163.5
220.5
160
217
3.5
3.5
19.0
19.0
2
2
69.5
117.5
69.5
117.5
134.5
182.5
131
179
3.5
3.5
19.1
19.1
1
1
101.0
159.5
103.5
163.5
168.5
228.5
165
225
3.5
3.5
20.0
20.0
2
2
69.5
117.5
69.5
117.5
134.5
182.5
131
179
3.5
3.5
19.2
19.2
1
1
101.0
159.5
103.5
163.5
168.5
228.5
165
225
3.5
3.5
20.0
20.0
2
2
69.5
117.5
69.5
117.5
134.5
182.5
131
179
3.5
3.5
19.3
19.3
1
1
101.0
159.5
103.5
163.5
168.5
228.5
165
225
3.5
3.5
20.0
20.0
2
2
69.5
117.5
69.5
117.5
134.5
182.5
131
179
3.5
3.5
19.4
19.4
1
1
101.0
159.5
103.5
163.5
168.5
228.5
165
225
3.5
3.5
20.0
20.0
2
2
69.5
117.5
69.5
117.5
134.5
182.5
131
179
3.5
3.5
19.5
19.5
1
1
101.0
159.5
103.5
163.5
168.5
228.5
165
225
3.5
3.5
20.0
20.0
2
2
69.6
117.6
69.6
117.6
134.6
182.6
131
179
3.6
3.6
19.6
19.6
1
1
103.6
163.6
103.6
163.6
168.6
228.6
165
225
3.6
3.6
20.0
20.0
2
2
CUTTING CONDITIONS
OPERATION GUIDANCE
TECHNICAL DATA
N115
N119
Q001
DRILLING
(mm)
Stock
VP15TF
DC
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
N111
MZE/MZS
DC
(mm)
19.7
19.8
19.9
20.0
Stock
Dimensions (mm)
VP15TF
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
Order Number
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
2
3
Ext.
Ext.
3
5
Int.
Int.
MZE1970SA
MZE1970MA
MZS1970MB
MZS1970LB
MZE1980SA
MZE1980MA
MZS1980MB
MZS1980LB
MZE1990SA
MZE1990MA
MZS1990MB
MZS1990LB
MZE2000SA
MZE2000MA
MZS2000MB
MZS2000LB
(l/d)
LH
OAL
LF
PL
DCON
69.6
117.6
69.6
117.6
134.6
182.6
131
179
3.6
3.6
19.7
19.7
1
1
103.6
163.6
103.6
163.6
168.6
228.6
165
225
3.6
3.6
20.0
20.0
2
2
69.6
117.6
69.6
117.6
134.6
182.6
131
179
3.6
3.6
19.8
19.8
1
1
103.6
163.6
103.6
163.6
168.6
228.6
165
225
3.6
3.6
20.0
20.0
2
2
69.6
117.6
69.6
117.6
134.6
182.6
131
179
3.6
3.6
19.9
19.9
1
1
103.6
163.6
103.6
163.6
168.6
228.6
165
225
3.6
3.6
20.0
20.0
2
2
69.6
117.6
69.6
117.6
134.6
182.6
131
179
3.6
3.6
20.0
20.0
1
1
103.6
163.6
103.6
163.6
168.6
228.6
165
225
3.6
3.6
20.0
20.0
2
2
DRILLING
N112
Type
LCF
MZE/MZS
STEP DRILLS
P
Steel
a Pre-hole drilling for metric screw thread.

a Helical coolant hole enables high speed machining (MZS type).
CARBIDE
3<DC < 6 6<DC < 10 10<DC < 18
(MZE only)
h6
MZE (External coolant)
MZE
MZS
PL
0
0.018
0
0.018
0
0.008
0
0.022
0
0.022
0
0.009
0
0.027
0
0.027
0
0.011
LF
LCF
MZS (Internal coolant)

140
DC(h8)
SDL
LCF
4.3
5.1
6.8
8.5
10.3
2
2
Ext.
3
3
Ext.
2
2
Ext.
3
3
Ext.
2
2
Ext.
3
3
Ext.
2
2
Ext.
3
3
Ext.
2
2
Ext.
3
3
Ext.
2
2
Ext.
3
3
Ext.
Int.
Int.
Int.
Int.
Int.
Int.
Int.
Int.
Int.
Int.
Int.
Int.
MZE0340SM04
MZS0340SM04
MZE0340MM04
MZS0340MM04
MZE0430SM05
MZS0430SM05
MZE0430MM05
MZS0430MM05
MZE0510SM06
MZS0510SM06
MZE0510MM06
MZS0510MM06
MZE0680SM08
MZS0680SM08
MZE0680MM08
MZS0680MM08
MZE0850SM10
MZS0850SM10
MZE0850MM10
MZS0850MM10
MZE1030SM12
MZS1030SM12
MZE1030MM12
MZS1030MM12
VP15TF
M4
M4
M4
M4
M5
M5
M5
M5
M6
M6
M6
M6
M8
M8
M8
M8
M10
M10
M10
M10
M12
M12
M12
M12
OAL
Dimensions (mm)
Type
SDL
LCF
OAL
LF
PL
DCON
8.6
8.6
21.6
21.6
73.6
73.6
73
73
0.6
0.6
6.0
6.0
1
2
12.6
12.6
25.6
25.6
77.6
77.6
77
77
0.6
0.6
6.0
6.0
1
2
10.8
10.8
26.8
26.8
79.8
79.8
79
79
0.8
0.8
7.0
7.0
1
2
15.8
15.8
31.8
31.8
84.8
84.8
84
84
0.8
0.8
7.0
7.0
1
2
12.9
12.9
30.9
30.9
84.9
84.9
84
84
0.9
0.9
8.0
8.0
1
2
18.9
18.9
36.9
36.9
90.9
90.9
90
90
0.9
0.9
8.0
8.0
1
2
17.2
17.2
41.2
41.2
97.2
97.2
96
96
1.2
1.2
10.0
10.0
1
2
25.2
25.2
49.2
49.2
105.2
105.2
104
104
1.2
1.2
10.0
10.0
1
2
21.5
21.5
51.5
51.5
113.5
113.5
112
112
1.5
1.5
12.0
12.0
1
2
31.5
31.5
61.5
61.5
123.5
123.5
122
122
1.5
1.5
12.0
12.0
1
2
25.9
25.9
61.9
61.9
125.9
125.9
124
124
1.9
1.9
14.0
14.0
1
2
37.9
37.9
73.9
73.9
137.9
137.9
136
136
1.9
1.9
14.0
14.0
1
2
DRILLING
3.4
(l/d)
Order Number
Thread Size
(mm)
Coolant
(Int./Ext.)
DC
Stock
Type2
LF
90
Hole
Depth
Type1
OAL
PL
(Note 1) MZS type bigger than &5.0 have a recess in the end face.
(Note 2) Spot face drilling is not possible (chamfering only).
(Note 3) For metric coarse thread.
(Note 4) MZS type also available for shrink fit holder.
DCON
SDL
DCON(h6)
140
DC(h8)
90
(Note) Please contact us for any geometry that is not in the catalogue (e.g. different diameter and length).
OPERATION GUIDANCE
N119
N113
CARBIDE
MZE/MZS
STEP DRILLS
y CAUTION FOR USE
2.
1.
4.
3.
Spot facing as shown above is not possible due Chips from the chamfer machining tend to be elongated Cutting resistance increases on initial contact
to the large diameter not having a back taper. and may cause jamming. It is recommended to pick with the chamfer. Reduce feed at this point.
Please contact us if spot face drills are required.
feed to reduce the length of chips.
The width of the chamfer is C1.0 for M4M6,

and C1.5 for M8M12. For widths other than
those stated above please contact us.
y DRILL SIZE AND HOLE DIAMETERS FOR TAPPING

For Metric Coarse Screw Thread
Thread Size
For Metric Coarse Screw Thread
Initial Thread Diameter Tolerance MZE/MZS Drill

Application DC
max.
min.
Reference
HSS Drill
Thread Size
M9x1.25
Initial Thread Diameter Tolerance MZE/MZS Drill

Application DC
max.
min.
M2.5x0.45
2.138
2.013
2.1
2.1
7.912
7.647
7.8
7.8
M3x0.5
2.599
2.459
2.5
2.5
M10x1.5
8.676
8.376
8.5
8.5
M3.5x0.6
3.010
2.850
2.9
2.9
M11x1.5
9.676
9.376
9.5
9.5
M4x0.7
3.422
3.242
3.4
3.3
M12x1.75
10.441
10.106
10.3
10.3
M4.5x0.75
3.878
3.688
3.8
3.8
M14x2
12.210
11.835
12.0
12.0
M5x0.8
4.334
4.134
4.3
4.2
M16x2
14.210
13.835
14.0
14.0
M6x1
5.153
4.917
5.1
5.0
M18x2.5
15.744
15.294
15.5
15.5
M7x1.25
6.153
5.917
6.1
6.0
M20x2.5
17.744
17.294
17.5
17.5
M8x1.25
6.912
6.647
6.8
6.8
M22x2.5
19.744
19.294
19.5
19.5
DRILLING
(Note) Holes drilled with an MZE type drill should be +0.01 +0.03mm oversize.
For thread tapping and replacement of HSS drills, a drill approximately 0.1mm bigger is recommended.
N114
Reference
HSS Drill
CARBIDE
RECOMMENDED CUTTING CONDITIONS OF MZE/MZS DRILLS

y MZE (External coolant)
AISI 1010 etc
AISI 4340 etc
Dia.
DC
(mm)
Revolution
(min-1)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
12700
10600
8900
7100
5700
4400
3500
2800
2700
2100
1700
1700
1300
1100
Work
Material
Feed rate
(Min. Max.)
(mm/rev)
0.035
0.045
0.055
0.07
0.085
0.1
0.12
0.15
0.2
0.23
0.27
0.31
0.33
0.35
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.060 0.13)
(0.080 0.16)
(0.100 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
11100
9200
7900
6300
5000
3900
3100
2500
2500
1900
1500
1500
1200
1000
0.035
0.045
0.055
0.07
0.085
0.1
0.12
0.15
0.2
0.23
0.27
0.31
0.33
0.35
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
9500
7900
6900
5500
4400
3400
2700
2200
2200
1700
1400
1400
1100
900
0.035
0.045
0.055
0.07
0.085
0.09
0.11
0.14
0.18
0.21
0.23
0.26
0.29
0.3
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.12)
(0.07 0.14)
(0.09 0.18)
(0.11 0.24)
(0.16 0.25)
(0.19 0.27)
(0.23 0.29)
(0.24 0.33)
(0.26 0.34)
No 45 B etc
60-40-8 etc
Dia.
DC
(mm)
Revolution
(min-1)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
4700
3900
3900
3100
2500
1900
1500
1200
1200
900
700
600
400
300
Feed rate
(Min. Max.)
(mm/rev)
0.03
0.04
0.05
0.06
0.075
0.07
0.08
0.1
0.13
0.14
0.16
0.18
0.19
0.2
(0.020 0.044)
(0.030 0.053)
(0.035 0.070)
(0.040 0.080)
(0.050 0.100)
(0.05 0.08)
(0.06 0.10)
(0.07 0.13)
(0.09 0.17)
(0.10 0.18)
(0.12 0.19)
(0.15 0.20)
(0.15 0.23)
(0.15 0.24)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
14300
11900
9900
7900
6300
4900
3900
3100
3000
2300
1900
1800
1300
1100
0.035
0.045
0.055
0.07
0.085
0.1
0.12
0.15
0.2
0.25
0.29
0.33
0.35
0.37
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.31)
(0.22 0.35)
(0.28 0.37)
(0.28 0.42)
(0.30 0.44)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
12700
10600
8900
7100
5700
4400
3500
2800
2700
2100
1700
1700
1300
1100
0.035
0.045
0.055
0.07
0.085
0.1
0.12
0.15
0.2
0.23
0.27
0.31
0.33
0.35
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
DRILLING
Work
Material
TECHNICAL DATA
Q001
N115
CARBIDE
MZE/MZS
STEP DRILLS
y MZE (External coolant)
DRILLING
Work
Material
N116
Dia.
DC
(mm)
Revolution
(min-1)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
15900
13200
11900
9500
8900
7900
6300
5000
4500
3500
2800
2600
2100
1700
Feed rate
(Min. Max.)
(mm/rev)
0.05
0.065
0.085
0.105
0.135
0.1
0.12
0.15
0.2
0.23
0.27
0.31
0.33
0.35
(0.030 0.075)
(0.045 0.090)
(0.053 0.120)
(0.060 0.150)
(0.075 0.200)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
Inconel718 etc
AISI H13, L6 etc

Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
3100
2600
1900
2300
1900
1900
1500
1200
1200
900
700
600
400
400
0.02
0.025
0.03
0.04
0.05
0.07
0.09
0.11
0.14
0.14
0.16
0.16
0.18
0.19
(0.016 0.027)
(0.022 0.032)
(0.025 0.040)
(0.032 0.050)
(0.040 0.060)
(0.05 0.09)
(0.06 0.11)
(0.08 0.14)
(0.09 0.19)
(0.11 0.17)
(0.12 0.19)
(0.13 0.18)
(0.14 0.21)
(0.15 0.22)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
3100
2600
1900
2300
1900
1900
1500
1200
1200
900
700
600
500
400
0.02
0.03
0.03
0.04
0.05
0.07
0.09
0.11
0.14
0.14
0.16
0.16
0.18
0.19
(0.016 0.031)
(0.022 0.037)
(0.025 0.040)
(0.032 0.050)
(0.040 0.060)
(0.05 0.09)
(0.06 0.11)
(0.08 0.14)
(0.09 0.19)
(0.11 0.17)
(0.12 0.19)
(0.13 0.18)
(0.14 0.21)
(0.15 0.22)
CARBIDE
y MZS (Internal coolant)

AISI 1010 etc
AISI 4340 etc
Dia.
DC
(mm)
Revolution
(min-1)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
12700
10600
8900
7900
6300
7900
6300
5700
5000
4300
3800
3400
2700
2300
Work
Material
Feed rate
(Min. Max.)
(mm/rev)
0.035
0.045
0.055
0.07
0.085
0.1
0.12
0.15
0.2
0.23
0.27
0.3
0.33
0.35
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.26 0.34)
(0.27 0.38)
(0.30 0.40)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
9500
7900
6900
6300
5700
6900
6300
5700
4500
3900
3500
3100
2500
2200
0.035
0.045
0.055
0.07
0.085
0.1
0.12
0.15
0.2
0.23
0.27
0.3
0.33
0.35
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.28 0.34)
(0.28 0.38)
(0.30 0.40)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
9500
7900
6900
6300
5000
5900
5100
4400
3500
3100
2500
2300
1700
1500
0.035
0.045
0.055
0.07
0.085
0.1
0.11
0.14
0.18
0.21
0.23
0.26
0.28
0.3
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.07 0.14)
(0.09 0.18)
(0.11 0.24)
(0.16 0.25)
(0.19 0.27)
(0.22 0.29)
(0.23 0.33)
(0.26 0.34)
No 45 B etc
60-40-8 etc
Dia.
DC
(mm)
Revolution
(min-1)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
6300
5300
4900
4700
3800
2900
3100
2500
2200
1900
1500
1500
1200
1100
Feed rate
(Min. Max.)
(mm/rev)
0.03
0.04
0.05
0.06
0.075
0.08
0.09
0.11
0.14
0.15
0.16
0.18
0.19
0.21
(0.020 0.044)
(0.030 0.053)
(0.035 0.070)
(0.040 0.080)
(0.050 0.100)
(0.06 0.10)
(0.06 0.11)
(0.08 0.14)
(0.09 0.18)
(0.10 0.19)
(0.12 0.20)
(0.15 0.21)
(0.14 0.24)
(0.15 0.26)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
12700
10600
8900
7900
6300
7900
6300
5700
5000
4300
3800
3400
2700
2300
0.035
0.045
0.055
0.07
0.085
0.1
0.12
0.15
0.2
0.25
0.29
0.32
0.35
0.37
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.31)
(0.22 0.35)
(0.26 0.37)
(0.27 0.42)
(0.30 0.44)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
9500
7900
6900
6300
5000
5900
5100
4400
3500
3100
2500
2300
1700
1500
0.035
0.045
0.055
0.07
0.085
0.1
0.12
0.15
0.2
0.23
0.27
0.3
0.33
0.35
(0.020 0.050)
(0.030 0.060)
(0.035 0.080)
(0.040 0.100)
(0.050 0.125)
(0.06 0.13)
(0.08 0.16)
(0.10 0.20)
(0.13 0.26)
(0.18 0.28)
(0.22 0.32)
(0.26 0.34)
(0.28 0.38)
(0.30 0.40)
DRILLING
Work
Material
TECHNICAL DATA
Q001
N117
CARBIDE
MZE/MZS
STEP DRILLS
y MZS (Internal coolant)
DRILLING
Work
Material
N118
Inconel718 etc
Dia.
DC
(mm)
Revolution
(min-1)
1.0
1.2
1.6
2.0
2.5
3.2
4.0
5.0
6.3
8.0
10.0
12.0
16.0
20.0
19000
15900
13900
11100
10100
9900
7900
7000
6000
4700
4100
3900
3300
2700
Feed rate
(Min. Max.)
(mm/rev)
0.05
0.065
0.085
0.105
0.135
0.23
0.24
0.25
0.35
0.35
0.5
0.5
0.6
0.6
(0.030 0.075)
(0.045 0.090)
(0.053 0.120)
(0.060 0.150)
(0.075 0.200)
(0.10 0.35)
(0.12 0.35)
(0.15 0.35)
(0.20 0.50)
(0.20 0.50)
(0.20 0.80)
(0.20 0.80)
(0.20 1.00)
(0.20 1.00)
Feed rate
(Min. Max.)
(mm/rev)
Revolution
(min-1)
3100
2600
1900
1500
1200
1400
1100
1200
1200
900
700
600
500
400
0.02
0.025
0.03
0.04
0.05
0.07
0.09
0.11
0.13
0.14
0.15
0.16
0.18
0.19
(0.016 0.027)
(0.022 0.032)
(0.025 0.040)
(0.032 0.050)
(0.040 0.060)
(0.05 0.09)
(0.06 0.11)
(0.08 0.14)
(0.09 0.16)
(0.11 0.17)
(0.12 0.17)
(0.13 0.18)
(0.14 0.21)
(0.15 0.22)
CARBIDE
Drill Installation
A > DC x 1.5
Run-out < 0.03mm
Through Coolant Type (MZS)
Drill Installation
Coolant Handling
Drill Length
Adjusting Screw
Drill Holding

Coolant Method (MZE)
DC
Revolving
Coolant
Machine Type
<MZS Type>

1DC
Spindles
Through
Coolant Type

end and at the center are ideal.

0.51MPa (<&5:23MPa).
zWhen machining a prepared hole

with the MZE-SA please set the
depth to 1DC (DC=drill diameter).
Thin Workpiece
Interrupted Cutting
Stepped Holes

coolant exchange is
recommended.
One Process
If Bending
Occurs
zLower the feed

when drilling
the interrupted
part.
Requires Prior
Machining
Support
the Workpiece

cutting.
xAdd a 45chamfer.

zSpot face with

an end mill
prior to drilling.
DRILLING
y CAUTION TO USE MZS TYPE (Drill Diameter < &3)

aPlease use a fine mesh filter (mesh < 3!m) for coolant to prevent jamming in the oil hole.
aFor deep drilling (l/d>3), machining guiding hole is recommended. (Use MZEppppSA type for guiding hole.)
aPick drilling is also effective.
y CUTTING RESISTANCE
Workpiece : JIS SCM440(300HB) Cutting Speed : 50m/min
m
.3m
f=0 m/rev
m
.2
0
=
f
m/rev
f=0.1m
5
10
15
20
Drill Diameter (mm)
m/
3000
.3m
f=0 rev
/
m
.2m m/rev
0
=
f .1m
f=0
2000
1000
10
15
20
5
Drill Diameter (mm)
Thrust (N)
/rev
0.4
m
.4m
f=0
re
m/
f=
m/
8000
re
v
4000
rev
Torque (N cm)
Power Consumption (kW)
Thrust
Torque
Power Consumption
6000
4000
2000
rev
m/
.4m
f=0
ev
m/r
.3m m/rev
0
=
f
2m
f=0. /rev
mm
f=0.1
10
15
20
5
Drill Diameter (mm)
N119
MSE
MIRACLE MINI STAR DRILL
M
Steel
0.10 < DC < 0.99
0
0.009
0
0.006
h6
PL
DC
LF
130
LCF
DCON(h6)
a Wide flute for preventing chip jamming.

a Stable, small diameter machining.
Type1
DCON(h6)
CARBIDE
Type2
LH
OAL
PL
DC
LF
130
LCF
LH
OAL
(Note) MSE drills are suitable for use with shrink fit holders.
External Coolant
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
1.43 9.73 38.03 38
0.03
2.03 9.73 38.03 38
0.03
2.03 9.73 38.03 38
0.03
2.04 9.74 38.04 38
0.04
2.04 9.74 38.04 38
0.04
2.04 9.74 38.04 38
0.04
2.04 9.74 38.04 38
0.04
2.55 9.75 38.05 38
0.05
2.55 9.75 38.05 38
0.05
2.55 9.75 38.05 38
0.05
2.55 9.75 38.05 38
0.05
3.06 9.76 38.06 38
0.06
3.06 9.76 38.06 38
0.06
3.06 9.76 38.06 38
0.06
3.06 9.76 38.06 38
0.06
3.07 9.77 38.07 38
0.07
3.07 9.77 38.07 38
0.07
5.07 10.27 38.07 38
0.07
5.07 10.27 38.07 38
0.07
5.07 10.27 38.07 38
0.07
5.08 10.28 38.08 38
0.08
6.08 11.28 38.08 38
0.08
6.08 11.18 38.08 38
0.08
6.08 11.18 38.08 38
0.08
6.09 11.19 38.09 38
0.09
6.09 11.19 38.09 38
0.09
6.09 11.19 38.09 38
0.09
7.09 12.19 38.09 38
0.09
7.10 12.10 38.10 38
0.10
7.10 12.10 38.10 38

7.10 12.10 38.10 38
0.10
0.10
3
3
2
2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
MSE0044SB
MSE0045SB
MSE0046SB
MSE0047SB
MSE0048SB
MSE0049SB
MSE0050SB
MSE0051SB
MSE0052SB
MSE0053SB
MSE0054SB
MSE0055SB
MSE0056SB
MSE0057SB
MSE0058SB
MSE0059SB
MSE0060SB
MSE0061SB
MSE0062SB
MSE0063SB
MSE0064SB
MSE0065SB
MSE0066SB
MSE0067SB
MSE0068SB
MSE0069SB
MSE0070SB
MSE0071SB
MSE0072SB
MSE0073SB
MSE0074SB
MSE0075SB
MSE0076SB
MSE0077SB
N120
7.10 12.10 38.10 38

7.10 12.10 38.10 38
0.10
0.10
3
3
2
2
7.11 12.01 38.11 38
0.11
7.11 12.01 38.11 38
0.11
7.11 12.01 38.11 38
0.11
7.11 12.01 38.11 38
0.11
7.12 12.02 38.12 38
0.12
7.12 11.92 38.12 38
0.12
7.12 11.92 38.12 38
0.12
7.12 11.92 38.12 38
0.12
7.13 11.93 38.13 38
0.13
7.13 11.93 38.13 38
0.13
7.13 11.93 38.13 38
0.13
OAL
Type
LCF
(mm)
VP15TF
0.03
0.44
0.45
0.46
0.47
0.48
0.49
0.50
0.51
0.52
0.53
0.54
0.55
0.56
0.57
0.58
0.59
0.60
0.61
0.62
0.63
0.64
0.65
0.66
0.67
0.68
0.69
0.70
0.71
0.72
0.73
0.74
0.75
0.76
0.77
VP20MF
1.43 9.73 38.03 38
OAL
1
1
LH
3
3
DCON
0.02
0.03
Order Number
PL
1.22 9.72 38.02 38

1.23 9.73 38.03 38
DC
Dimensions (mm)
LF
DCON
PL
MSE0010SB
MSE0011SB
MSE0012SB
MSE0013SB
MSE0014SB
MSE0015SB
MSE0016SB
MSE0017SB
MSE0018SB
MSE0019SB
MSE0020SB
MSE0021SB
MSE0022SB
MSE0023SB
MSE0024SB
MSE0025SB
MSE0026SB
MSE0027SB
MSE0028SB
MSE0029SB
MSE0030SB
MSE0031SB
MSE0032SB
MSE0033SB
MSE0034SB
MSE0035SB
MSE0036SB
MSE0037SB
MSE0038SB
MSE0039SB
MSE0040SB
MSE0041SB
MSE0042SB
MSE0043SB
Type
LCF
VP15TF
Order Number
Stock
LF
DRILLING
(mm)
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.17
0.18
0.19
0.20
0.21
0.22
0.23
0.24
0.25
0.26
0.27
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.41
0.42
0.43
VP20MF
DC
Dimensions (mm)
LH
External Coolant
Stock
7.13 11.83 38.13 38
0.13
7.14 11.84 38.14 38
0.14
7.14 11.84 38.14 38
0.14
7.14 11.84 38.14 38
0.14
7.14 11.84 38.14 38
0.14
7.14 11.74 38.14 38
0.14
7.15 11.75 38.15 38
0.15
7.15 11.75 38.15 38
0.15
7.15 11.75 38.15 38
0.15
7.15 11.75 38.15 38
0.15
7.16 11.66 38.16 38
0.16
7.16 11.66 38.16 38
0.16
7.16 11.66 38.16 38
0.16
8.16 12.66 38.16 38
0.16
8.17 12.67 38.17 38
0.17
8.17 12.67 38.17 38
0.17
8.17 12.57 38.17 38
0.17
8.17 12.57 38.17 38
0.17
8.17 12.57 38.17 38
0.17
8.18 12.58 38.18 38

8.18 12.58 38.18 38
0.18
0.18
3
3
2
2
CARBIDE
a
a
a
a
a
10.19 14.49 38.19 38
0.19
10.19 14.49 38.19 38
0.19
10.19 14.49 38.19 38
0.19
10.20 14.40 38.20 38
0.20
10.20 14.40 38.20 38
0.20
10.20 14.40 38.20 38
0.20
10.20 14.40 38.20 38

10.21 14.41 38.21 38
0.20
0.21
3
3
2
2
a
a
a
a
a
a
a
a
a
a
MSE0089SB
MSE0090SB
MSE0091SB
MSE0092SB
MSE0093SB
MSE0094SB
MSE0095SB
MSE0096SB
MSE0097SB
MSE0098SB
MSE0099SB
10.21 14.31 38.21 38
0.21
10.21 14.31 38.21 38
0.21
10.21 14.31 38.21 38
0.21
10.21 14.31 38.21 38
0.21
10.22 14.32 38.22 38
0.22
10.22 14.22 38.22 38
0.22
10.22 14.22 38.22 38
0.22
10.22 14.22 38.22 38
0.22
10.23 14.23 38.23 38
0.23
10.23 14.23 38.23 38

10.23 14.23 38.23 38
0.23
0.23
3
3
2
2
OAL
Type
LCF
0.89
0.90
0.91
0.92
0.93
0.94
0.95
0.96
0.97
0.98
0.99
VP15TF
0.19
VP20MF
10.19 14.49 38.19 38
OAL
2
2
LH
3
3
DCON
0.18
0.18
(mm)
Order Number
PL
8.18 12.48 38.18 38

8.18 12.48 38.18 38
DC
Dimensions (mm)
LF
DCON
MSE0078SB
MSE0079SB
MSE0080SB
MSE0081SB
MSE0082SB
MSE0083SB
MSE0084SB
MSE0085SB
MSE0086SB
MSE0087SB
MSE0088SB
Type
PL
a
a
Order Number
Stock
LF
0.78
0.79
0.80
0.81
0.82
0.83
0.84
0.85
0.86
0.87
0.88
Dimensions (mm)
LCF
(mm)
VP15TF
DC
VP20MF
Stock
External Coolant
LH
External Coolant
Work
Material
Dia.
DC
(mm)
0.1
0.12
0.16
0.2
0.25
0.32
0.4
0.5
0.63
0.8
0.99
Work
Material
Dia.
DC
(mm)
0.1
0.12
0.16
0.2
0.25
0.32
0.4
0.5
0.63
0.8
0.99
AISI 1010 etc

Feed rate
(Min. Max.)
(mm/rev)

(m/min) (min-1)
6
8
10
13
16
20
25
31
40
50
62
20000
20000
20000
20000
20000
20000
20000
20000
20000
20000
20000
0.002
0.002
0.002
0.003
0.003
0.004
0.004
0.006
0.008
0.02
0.04
(0.001 0.003)
(0.001 0.003)
(0.001 0.003)
(0.002 0.004)
(0.002 0.004)
(0.003 0.005)
(0.003 0.005)
(0.005 0.007)
(0.006 0.01)
(0.015 0.025)
(0.03 0.05)
Step
(mm)
0.02
0.02
0.02
0.04
0.04
0.05
0.05
0.1
0.1
0.3
0.3
Feed rate
(Min. Max.)
(mm/rev)

(mm/min) (m/min) (min-1)
40
40
40
60
60
80
80
120
160
400
800
6
8
10
13
16
20
25
31
40
50
62
20000
20000
20000
20000
20000
20000
20000
20000
20000
20000
20000
0.002
0.002
0.002
0.003
0.003
0.004
0.004
0.006
0.008
0.015
0.02
(0.001 0.003)
(0.001 0.003)
(0.001 0.003)
(0.002 0.004)
(0.002 0.004)
(0.003 0.005)
(0.003 0.005)
(0.005 0.007)
(0.006 0.01)
(0.012 0.018)
(0.015 0.025)
Pre-Hardened Steel (35 45HRC)
AISI 4340 etc
AISI P21, AISI P20 etc

Feed rate
(Min. Max.)
(mm/rev)

(m/min) (min-1)
6
8
10
13
16
20
25
31
40
50
62
20000
20000
20000
20000
20000
20000
20000
20000
20000
20000
20000
0.002
0.002
0.002
0.003
0.003
0.004
0.004
0.006
0.008
0.015
0.02
(0.001 0.003)
(0.001 0.003)
(0.001 0.003)
(0.002 0.004)
(0.002 0.004)
(0.003 0.005)
(0.003 0.005)
(0.005 0.007)
(0.006 0.01)
(0.012 0.018)
(0.015 0.025)
Step
(mm)
0.02
0.02
0.02
0.04
0.04
0.05
0.05
0.1
0.1
0.3
0.3
Feed rate
(Min. Max.)
(mm/rev)

40
40
40
60
60
80
80
120
160
300
400
6
8
10
13
16
20
25
31
40
50
62
20000
20000
20000
20000
20000
20000
20000
20000
20000
20000
20000
0.002
0.002
0.002
0.003
0.003
0.004
0.004
0.006
0.008
0.015
0.02
(0.001 0.003)
(0.001 0.003)
(0.001 0.003)
(0.002 0.004)
(0.002 0.004)
(0.003 0.005)
(0.003 0.005)
(0.005 0.007)
(0.006 0.01)
(0.012 0.018)
(0.015 0.025)
Step
(mm)
Table Feed
(mm/min)
0.02
0.02
0.02
0.04
0.04
0.05
0.05
0.1
0.1
0.3
0.3
40
40
40
60
60
80
80
120
160
300
400
Step
(mm)
Table Feed
(mm/min)
0.02
0.02
0.02
0.04
0.04
0.05
0.05
0.1
0.1
0.3
0.3
40
40
40
60
60
80
80
120
160
300
400
DRILLING
1) When drilling holes up to &0.3mm, the use of a spot drill is recommended.

(Order number : MSP0300SB, Cutting conditions : See below.)
2) Change cutting conditions depending on your machine and workpiece rigidity.
3) When machining holes over 5D, reduce the step stated above.
4) The use of water-soluble fluid (diluted by 20 times) is recommended for drilling under the cutting conditions above.
Lower the revolutions if you use oil fluid or mist.
TECHNICAL DATA
Q001
N121
CARBIDE
MSE
MIRACLE MINI STAR DRILL
Work
Material
Dia.
DC
(mm)
0.1
0.12
0.16
0.2
0.25
0.32
0.4
0.5
0.63
0.8
0.99
No 45 B etc
Feed rate
(Min. Max.)
(mm/rev)

(m/min) (min-1)
6
8
10
11
14
15
19
16
20
15
19
20000
20000
20000
18000
18000
15000
15000
10000
10000
6000
6000
0.002
0.002
0.002
0.003
0.003
0.004
0.004
0.006
0.008
0.015
0.02
(0.001 0.003)
(0.001 0.003)
(0.001 0.003)
(0.002 0.004)
(0.002 0.004)
(0.003 0.005)
(0.003 0.005)
(0.005 0.007)
(0.006 0.01)
(0.012 0.018)
(0.015 0.025)
Step
(mm)
0.02
0.02
0.02
0.04
0.04
0.05
0.05
0.1
0.1
0.2
0.2
40
40
40
54
54
60
60
60
80
90
120
0.1
0.12
0.16
0.2
0.25
0.32
0.4
0.5
0.63
0.8
0.99
6
8
10
13
16
20
25
31
40
50
62
20000
20000
20000
20000
20000
20000
20000
20000
20000
20000
20000
0.002
0.002
0.002
0.003
0.003
0.004
0.004
0.006
0.008
0.02
0.04
(0.001 0.003)
(0.001 0.003)
(0.001 0.003)
(0.002 0.004)
(0.002 0.004)
(0.003 0.005)
(0.003 0.005)
(0.005 0.007)
(0.006 0.01)
(0.015 0.025)
(0.03 0.05)
DRILLING
Table Feed
(mm/min)
0.02
0.02
0.02
0.04
0.04
0.05
0.05
0.1
0.1
0.3
0.3
40
40
40
60
60
80
80
120
160
400
800
Step
(mm)
Table Feed
(mm/min)
0.02
0.02
0.02
0.04
0.04
0.05
0.05
0.1
0.1
0.2
0.2
7
7
7
10
10
8
8
9
12
10.8
18
Inconel718 etc
Feed rate
(Min. Max.)
(mm/rev)

(m/min) (min-1)
6
8
10
13
16
20
25
31
40
50
62
20000
20000
20000
20000
20000
20000
20000
20000
20000
20000
20000
0.002
0.003
0.004
0.006
0.008
0.01
0.02
0.03
0.04
0.05
0.06
(0.001 0.003)
(0.002 0.004)
(0.003 0.005)
(0.005 0.007)
(0.006 0.01)
(0.008 0.012)
(0.015 0.025)
(0.025 0.035)
(0.035 0.045)
(0.045 0.055)
(0.055 0.065)
Step
(mm)
0.05
0.05
0.05
0.1
0.1
0.3
0.3
0.5
0.5
0.8
0.8
Feed rate
(Min. Max.)
(mm/rev)

40
60
80
120
160
200
400
600
800
1000
1200
2
3
4
3
4
4
5
5
6
5
6
7000
7000
7000
5000
5000
4000
4000
3000
3000
1800
1800
0.001
0.001
0.001
0.002
0.002
0.002
0.002
0.003
0.004
0.006
0.01
(0.0005 0.001)
(0.0005 0.001)
(0.0005 0.001)
(0.001 0.002)
(0.001 0.002)
(0.001 0.002)
(0.001 0.002)
(0.001 0.003)
(0.002 0.004)
(0.004 0.006)
(0.008 0.01)
1) When drilling holes up to &0.3mm, the use of a spot drill is recommended.

(Order number : MSP0300SB, Cutting conditions : See below.)
2) Change cutting conditions depending on your machine and workpiece rigidity.
3) When machining holes over 5D, reduce the step stated above.
4) The use of water-soluble fluid (diluted by 20 times) is recommended for drilling under the cutting conditions above.
Lower the revolutions if you use oil fluid or mist.
N122
Step
(mm)
Work
Material
Dia.
DC
(mm)
Feed rate
(Min. Max.)
(mm/rev)

MSP
SPOT DRILL
0
1.5
DCON-0.005
90
DC
CARBIDE
OAL
Order Number
Grade
Stock
Dimensions (mm)
DC
MSP0300SB
VP15TF
OAL DCON
Diameter
Range
(mm)
38
0.13.0

Hole Size Range Revolution
(mm)
(min-1)
10000
Table Feed
(mm/min)
0.0005 (0.00025 0.001)
DRILLING
0.1 3.0
Feed rate
(Min. Max.)
(mm/rev)

TECHNICAL DATA
Q001
N123
MGS
SOLID GUN DRILL
P
DC -0.005
Steel
a Micro deep hole drilling is possible.

a Excellent run-out accuracy ensures high precision drilling.
DCON -0.006
CARBIDE
LCF
OAL
(l/d)
0.7
50
80
Int.
Int.
0.8
45
70
Int.
Int.
0.9
40
60
Int.
Int.
Int.
1.0
35
55
75
Int.
Int.
30
50
65
Int.
Int.
Int.
30
45
60
Int.
Int.
Int.
40
55
70
Int.
Int.
Int.
35
50
65
Int.
Int.
Int.
35
50
60
Int.
Int.
Int.
30
45
55
Int.
Int.
Int.
30
40
55
Int.
Int.
Int.
MGS0070L040B
MGS0070L060B
MGS0080L040B
MGS0080L060B
MGS0090L040B
MGS0090L060B
MGS0100L040B
MGS0100L060B
MGS0100L080B
MGS0110L040B
MGS0110L060B
MGS0110L080B
MGS0120L040B
MGS0120L060B
MGS0120L080B
MGS0130L060B
MGS0130L080B
MGS0130L100B
MGS0140L060B
MGS0140L080B
MGS0140L100B
MGS0150L060B
MGS0150L080B
MGS0150L100B
MGS0160L060B
MGS0160L080B
MGS0160L100B
MGS0170L060B
MGS0170L080B
MGS0170L100B
1.1
1.2
1.3
1.4
1.5
DRILLING
1.6
1.7
DC
Order Number
(mm)
(l/d)
30
40
50
Int.
1.8
Int.
Int.
25
35
45
Int.
1.9
Int.
Int.
Int.
2.0
25
35
45
Int.
Int.
2.1
35
40
Int.
Int.
2.2
30
40
Int.
Int.
2.3
30
40
Int.
Int.
2.4
30
35
Int.
Int.
2.5
25
35
Int.
Int.
2.6
25
35
Int.
Int.
2.7
25
30
Int.
Int.
2.8
25
30
Int.
Int.
2.9
20
30
Int.
Int.
3.0
20
30
Int.
Int.
MGS0180L060B
MGS0180L080B
MGS0180L100B
MGS0190L060B
MGS0190L080B
MGS0190L100B
MGS0200L060B
MGS0200L080B
MGS0200L100B
MGS0210L080B
MGS0210L100B
MGS0220L080B
MGS0220L100B
MGS0230L080B
MGS0230L100B
MGS0240L080B
MGS0240L100B
MGS0250L080B
MGS0250L100B
MGS0260L080B
MGS0260L100B
MGS0270L080B
MGS0270L100B
MGS0280L080B
MGS0280L100B
MGS0290L080B
MGS0290L100B
MGS0300L080B
MGS0300L100B
LCF OAL DCON
40
80
60 100
3
3
40
80
60 100
3
3
40
80
60 100
3
3
40
80
60 100
80 120
3
3
3
40
80
60 100
80 120
3
3
3
40
80
60 100
80 120
3
3
3
60 100
80 120
100 140
3
3
3
60 100
80 120
100 140
3
3
3
60 100
80 120
100 140
3
3
3
60 100
80 120
100 140
3
3
3
60 100
80 120
100 140
3
3
3
(Note) Please consult us regarding coated type drills (VP, GP and UP coated carbide).
N124
Dimensions (mm)
Stock
Hole
Depth
HTi10
Order Number
(mm)
HTi10
DC
Dimensions (mm)
Stock
Coolant
(Int./Ext.)
Hole
Depth
Coolant
(Int./Ext.)
(Note) MGS drills are suitable for use with shrink fit holders.
LCF OAL DCON
60 100
80 120
100 140
3
3
3
60 100
80 120
100 140
3
3
3
60 100
80 120
100 140
3
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
80 120
100 140
3
3
CARBIDE
y DRIVER
y WHEN CONNECTED WITH A DRIVER
DCB
DCON
M4
Order Number
MGD38
MGD70
Stock
L26
LF
LCF
Flute length
L3
(15)
LF
Dimensions (mm)
DCON DCB
a
a
12.7
12.7
3.0
3.0
LF
L3
38.1
70.0
12.6
25.0
L26
Set Screw Wrench
12.7 HSS04004 HKY20F

20.0 HSS04004 HKY20F

AISI 1010 etc
Recommended
Water insoluble
grinding fluid
Dia.
DC
(mm)
0.8
1.0
1.2
1.6
2.0
2.5
3.0
Work
Material
Water insoluble

(m/min)
(min-1)
50
50
60
60
60
70
70
19800
15900
15900
11900
9500
8900
7400
Feed rate
(Min.Max.)
(mm/rev)
0.01
0.01
0.015
0.02
0.025
0.03
0.04
(0.005 0.016)
(0.007 0.020)
(0.008 0.024)
(0.011 0.032)
(0.013 0.040)
(0.017 0.050)
(0.020 0.060)
195
155
235
235
235
265
295
0.8
1.0
1.2
1.6
2.0
2.5
3.0
Work
Material
0.8
1.0
1.2
1.6
2.0
2.5
3.0
15900
12700
13200
9900
7900
7600
6300
0.01
0.01
0.015
0.02
0.025
0.03
0.04
AISI 4340 etc

(m/min)
(min-1)
30
30
40
40
40
50
50
11900
9500
10600
7900
6300
6300
5300
Feed rate
(Min.Max.)
(mm/rev)
0.005
0.005
0.005
0.01
0.01
0.015
0.015
(0.004 0.005)
(0.005 0.007)
(0.006 0.008)
(0.008 0.011)
(0.010 0.013)
(0.013 0.017)
(0.015 0.020)
Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)
55
45
50
75
60
90
75
155
125
195
195
195
225
250
30
30
30
40
40
40
40
11900
9500
7900
7900
6300
5000
4200
0.01
0.01
0.015
0.02
0.025
0.03
0.04
(0.005 0.016)
(0.007 0.020)
(0.008 0.024)
(0.011 0.032)
(0.013 0.040)
(0.017 0.050)
(0.020 0.060)
Table Feed
(mm/min)
115
95
115
155
155
150
165
No 45 B etc
60-40-8 etc
Water insoluble
Water soluble

(m/min)
(min-1)
50
50
60
60
60
70
70
(0.005 0.016)
(0.007 0.020)
(0.008 0.024)
(0.011 0.032)
(0.013 0.040)
(0.017 0.050)
(0.020 0.060)
Table Feed
(mm/min)
Water insoluble
Recommended Water insoluble

grinding fluid Water soluble
Dia.
DC
(mm)
40
40
50
50
50
60
60
Recommended
Water insoluble
grinding fluid
Dia.
DC
(mm)
Feed rate
(Min.Max.)
(mm/rev)

(m/min)
(mm/min)
(min-1)
DRILLING
Work
Material
19800
15900
15900
11900
9500
8900
7400
Feed rate
(Min.Max.)
(mm/rev)
0.01
0.015
0.015
0.02
0.03
0.035
0.045
(0.008 0.016)
(0.010 0.020)
(0.012 0.024)
(0.016 0.032)
(0.020 0.040)
(0.025 0.050)
(0.030 0.060)

(m/min)
(mm/min)
(min-1)
195
235
235
235
285
310
330
40
40
50
50
50
60
60
15900
12700
13200
9900
7900
7600
6300
Feed rate
(Min.Max.)
(mm/rev)
0.005
0.005
0.01
0.01
0.015
0.02
0.025
(0.005 0.008)
(0.007 0.010)
(0.008 0.012)
(0.011 0.016)
(0.013 0.020)
(0.017 0.025)
(0.020 0.030)
Table Feed
(mm/min)
75
60
130
95
115
150
155
1) For safety and success, high pressure coolant is required. (Minimum coolant pressure=1,000PSI)
2) Coolant filter must be less than 5 microns. Fine filtration is necessary to prevent blockage of the coolant holes.
3) A pilot hole or guide bushing is required.
TECHNICAL DATA
Q001
N125
CARBIDE
MGS
SOLID GUN DRILL
Work
Material
Recommended Water insoluble

grinding fluid Water soluble
Dia.
DC
(mm)
0.8
1.0
1.2
1.6
2.0
2.5
3.0
Water insoluble
Water soluble

(m/min)
(min-1)
50
60
70
80
90
100
100
19800
19000
18500
15900
14300
12700
10600
Feed rate
(Min.Max.)
(mm/rev)
0.01
0.015
0.015
0.02
0.03
0.035
0.045
(0.008 0.016)
(0.010 0.020)
(0.012 0.024)
(0.016 0.032)
(0.020 0.040)
(0.025 0.050)
(0.030 0.060)

(m/min)
(mm/min)
(min-1)
195
285
275
315
425
440
475
40
50
60
70
80
90
100
15900
15900
15900
13900
12700
11400
10600
Feed rate
(Min.Max.)
(mm/rev)
0.01
0.015
0.015
0.02
0.03
0.035
0.045
(0.008 0.016)
(0.010 0.020)
(0.012 0.024)
(0.016 0.032)
(0.020 0.040)
(0.025 0.050)
(0.030 0.060)
Table Feed
(mm/min)
155
235
235
275
380
395
475
1) For safety and success, high pressure coolant is required. (Minimum coolant pressure=1,000PSI)
2) Coolant filter must be less than 5 microns. Fine filtration is necessary to prevent blockage of the coolant holes.
3) A pilot hole or guide bushing is required.
SPECIAL APPLICATION NOTES

For safety and success, high pressure coolant is required.
(Minimum coolant pressure=1,000PSI)
Coolant filter must be less than 5 microns.
Fine filtration is necessary to prevent blockage of the coolant holes.
A pilot hole or guide bushing is required.
+0.030
1.5 3DC
DC +0.010
HOW TO USE
1. Pilot hole drilling.

(Mitsubishis MZE, MZS, MWE or MWS is
recommended.)
DRILLING
3. Coolant is turned ON, raise cutting speed and

feed to the recommended cutting condition.
N126
2. Drill is inserted into the pilot hole with the MSG drill rotation
stopped or rotating CCW at 300rpm or less.
a UP to 1-2mm before hole bottom.
4. Return to Pos 2 after drilling end, coolant

turned OFF and drill rotation is stopped.
MIRACLE DRILLS
VCSSS
Short, For steel (3mm shank series)
P
Steel
UWC
VC
130
120
Thinning
DC<0.6
CARBIDE
DC>0.7
DC < 2.4
h7
PL
0
0.014
0
0.010
DCON(h7)
DC(h8)
LF
LCF
OAL
a First recommendation for pilot hole drilling of hardened material.
Order Number
DC LCF OAL LF
PL DCON
VCSSSD0030
VCSSSD0040
VCSSSD0050
VCSSSD0060
VCSSSD0070
VCSSSD0080
VCSSSD0090
VCSSSD0100
VCSSSD0110
VCSSSD0120
VCSSSD0130
0.3 3.07 38.07 38

0.4 4.09 38.09 38
0.07
0.09
3
3
0.5 4.12 38.12 38
0.12
0.6 5.14 38.14 38
0.14
0.7 5.20 38.20 38
0.20
0.8 6.23 38.23 38
0.23
0.9 6.26 38.26 38
0.26
1.0 8.3
38.3
38
0.3
1.1 8.3
38.3
38
0.3
1.2 8.4
1.3 8.4
38.4
38.4
38
38
0.4
0.4
3
3
Stock
Stock
Unit : mm
Order Number
DC LCF OAL LF
PL DCON
VCSSSD0140
VCSSSD0150
VCSSSD0160
VCSSSD0170
VCSSSD0180
VCSSSD0190
VCSSSD0200
VCSSSD0210
VCSSSD0220
VCSSSD0230
VCSSSD0240
1.4 8.4 38.4

1.5 10.4 45.4
38
45
0.4
0.4
3
3
1.6 10.5 45.5
45
0.5
1.7 10.5 45.5
45
0.5
1.8 10.5 45.5
45
0.5
1.9 10.6 45.6
45
0.6
2.0 12.6 45.6
45
0.6
2.1 12.6 45.6
45
0.6
2.2 12.6 45.6
45
0.6
2.3 12.7 45.7

2.4 12.7 45.7
45
45
0.7
0.7
3
3

Heat-treated steel
AISI H13, AISI 4140 etc.
(4050HRC)
Hardened steel
AISI D2,
Powder high-speed steel etc.
(5560HRC)
Hardened steel
(5055HRC)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/rev)
Step feed
(mm)
Revolution
(min-1)
Feed rate
(mm/rev)
Step feed
(mm)
Revolution
(min-1)
Feed rate
(mm/rev)
Step feed
(mm)
0.3
0.5
21000
13000
0.005
0.005
0.03
0.05
16000
9600
0.005
0.005
0.03
0.05
11000
6400
0.005
0.005
0.03
0.05
0.8
8000
0.008
0.08
6000
0.008
0.08
4000
0.008
0.08
1.0
6400
0.01
0.10
4800
0.01
0.10
3200
0.01
0.10
1.2
5300
0.01
0.15
4000
0.01
0.15
2700
0.01
0.10
1.5
1.8
2.0
2.2
2.4
4200
3500
3200
2900
2700
0.02
0.03
0.04
0.04
0.05
0.20
0.25
0.30
0.40
0.50
3200
2700
2400
2200
2000
0.01
0.01
0.02
0.02
0.02
0.20
0.25
0.30
0.40
0.50
2100
1800
1600
1400
1300
0.01
0.01
0.02
0.02
0.02
0.20
0.20
0.30
0.30
0.30
DRILLING
Work
Material
1) Please use a machine with a high accuracy spindle.

2) A collet chuck is recommended to maintain shank condition.
3) Use emulsion as a cutting fluid.

TECHNICAL DATA
Q001
N127
MIRACLE DRILLS
CARBIDE
VCHSM
Medium, For hardened material
P
UWC
h6
VC
130
120
DC<6
140
DC>6
Thinning
DC < 3
3<DC < 6
6<DC < 10
10<DC < 16
0
0.014
0
0.009
0
0.018
0
0.012
0
0.022
0
0.015
0
0.027
0
0.018
PL
DCON(h6)
DC(h8)
LF
LCF
OAL
a A suitable geometry for high hardness (60 HRC) material drilling.
DRILLING
VCHSMD0250
VCHSMD0260
VCHSMD0270
VCHSMD0280
VCHSMD0290
VCHSMD0300
VCHSMD0310
VCHSMD0320
VCHSMD0330
VCHSMD0340
VCHSMD0350
VCHSMD0360
VCHSMD0370
VCHSMD0380
VCHSMD0390
VCHSMD0400
VCHSMD0410
VCHSMD0420
VCHSMD0430
VCHSMD0440
VCHSMD0450
VCHSMD0460
VCHSMD0470
VCHSMD0480
VCHSMD0490
VCHSMD0500
VCHSMD0510
VCHSMD0520
VCHSMD0530
VCHSMD0540
VCHSMD0550
VCHSMD0560
VCHSMD0570
VCHSMD0580
VCHSMD0590
VCHSMD0600
VCHSMD0650
VCHSMD0690
VCHSMD0700
VCHSMD0750
N128
DC LCF OAL LF
PL DCON
2.5
2.6
20.6 55.6
20.6 55.6
55
55
0.6
0.6
2.5
2.6
2.7
20.6 55.6
55
0.6
2.7
2.8
21.7 60.7
60
0.7
2.8
2.9
21.7 60.7
60
0.7
2.9
3.0
21.7 60.7
60
0.7
3.0
3.1
24.7 60.7
60
0.7
3.1
3.2
24.7 60.7
60
0.7
3.2
3.3
24.8 60.8
60
0.8
3.3
3.4
24.8 60.8
60
0.8
3.4
3.5
24.8 60.8
60
0.8
3.5
3.6
27.8 60.8
60
0.8
3.6
3.7
27.9 60.9
60
0.9
3.7
3.8
27.9 60.9
60
0.9
3.8
3.9
27.9 60.9
60
0.9
3.9
4.0
27.9 60.9
60
0.9
4.0
4.1
30.0 64.0
63
1.0
4.1
4.2
30.0 64.0
63
1.0
4.2
4.3
30.0 64.0
63
1.0
4.3
4.4
30.0 64.0
63
1.0
4.4
4.5
30.0 64.0
63
1.0
4.5
4.6
33.1 69.1
68
1.1
4.6
4.7
33.1 69.1
68
1.1
4.7
4.8
33.1 69.1
68
1.1
4.8
4.9
33.1 69.1
68
1.1
4.9
5.0
33.2 69.2
68
1.2
5.0
5.1
35.2 73.2
72
1.2
5.1
5.2
35.2 73.2
72
1.2
5.2
5.3
35.2 73.2
72
1.2
5.3
5.4
35.3 73.3
72
1.3
5.4
5.5
35.3 73.3
72
1.3
5.5
5.6
37.3 75.3
74
1.3
5.6
5.7
37.3 75.3
74
1.3
5.7
5.8
37.4 75.4
74
1.4
5.8
5.9
37.4 75.4
74
1.4
6.0
42.2 82.2
81
1.2
6.5
42.3 82.3
81
6.9
44.4 84.4
83
7.0
7.5
44.4 84.4
46.5 88.5
83
87
Order Number
VCHSMD0800
VCHSMD0850
VCHSMD0860
VCHSMD0900
VCHSMD0950
VCHSMD1000
VCHSMD1040
VCHSMD1050
VCHSMD1100
VCHSMD1150
VCHSMD1200
VCHSMD1250
VCHSMD1300
VCHSMD1350
VCHSMD1400
VCHSMD1450
VCHSMD1500
VCHSMD1550
VCHSMD1600
DC LCF OAL LF
PL DCON
8.0 49.6
8.5 54.7
91.6
97.7
90
96
1.6
1.7
8.0
8.5
8.6 56.7
99.7
98
1.7
8.6
9.0 56.8
99.8
98
1.8
9.0
9.5 59.9 103.9 102
1.9
9.5
10.0 62.0 107.0 105
2.0
10.0
10.4 68.1 114.1 112
2.1
10.4
10.5 68.1 114.1 112
2.1
10.5
11.0 70.2 116.2 114
2.2
11.0
11.5 73.3 120.3 118
2.3
11.5
12.0 75.4 123.4 121
2.4
12.0
12.5 78.5 137.5 135
2.5
12.5
13.0 80.6 139.6 137
2.6
13.0
13.5 86.7 146.7 144
2.7
13.5
14.0 88.8 149.8 147
2.8
14.0
14.5 91.9 153.9 151
2.9
14.5
15.0 94.0 156.0 153
3.0
15.0
15.5 97.2 160.2 157

16.0 99.3 163.3 160
3.2
3.3
15.5
16.0
a
a

Work
Material
Dia.
DC (mm)
Hardened steel
(5055HRC)
Hardened steel
AISI D2,
Powder high-speed steel etc.
(5560HRC)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
2.5
3.0
1900
1600
0.06
0.06
1300
1100
0.04
0.04
4.0
1200
0.06
800
0.04
5.0
6.0
8.0
10.0
1000
800
600
480
0.06
0.06
0.07
0.07
600
530
400
320
0.04
0.04
0.05
0.05
12.0
400
0.07
270
0.05
5.9
6.0
14.0
16.0
340
300
0.07
0.07
230
200
0.05
0.05
1.3
6.5
1.4
6.9
1.4
1.5
7.0
7.5
a
a
Stock
Order Number
Stock
Unit : mm
1) Use rigid machines.

2) Collet chuck is recommended to maintain shank condition.
3) Use emulsion as cutting fluid.
4) Recommended depth of drilling is 3DC (DC:drill diameter) under
these cutting conditions.
Cast Iron Non-ferrous Metal
h6
MAE (External coolant)
DC=3
3<DC < 6
6<DC < 10
10<DC < 16
+0.005
0
0
0.006
+0.005
0
0
0.008
+0.005
0
0
0.009
+0.005
0
0
0.011
DC
External Coolant
PL
LCF
MAS (Internal coolant)
DC
Internal Coolant
PL
3
3
6
Ext.
Int.
Int.
Ext.
3.1
3
3
6
Int.
Int.
Ext.
3.2
3
3
6
Int.
Int.
3
3
6
Ext.
3.3
Int.
Int.
Ext.
3.4
3
3
6
Int.
Int.
3
3
6
Ext.
3.5
Int.
Int.
Ext.
3.6
3
3
6
Int.
Int.
3
3
6
Ext.
Int.
Int.
a
a
3.7
3
3
6
Ext.
Int.
Int.
Ext.
3.8
3
3
6
Int.
Int.
Ext.
3.9
3
3
6
Int.
Int.
Ext.
4.0
3
3
6
Int.
Int.
3
3
6
Ext.
Int.
Int.
MAE0300MB
MAS0300MB
MAS0300LB
MAE0310MB
MAS0310MB
MAS0310LB
MAE0320MB
MAS0320MB
MAS0320LB
MAE0330MB
MAS0330MB
MAS0330LB
MAE0340MB
MAS0340MB
MAS0340LB
MAE0350MB
MAS0350MB
MAS0350LB
MAE0360MB
MAS0360MB
MAS0360LB
MAE0365MB
MAS0365MB
MAS0365LB
MAE0370MB
MAS0370MB
MAS0370LB
MAE0380MB
MAS0380MB
MAS0380LB
MAE0390MB
MAS0390MB
MAS0390LB
MAE0400MB
MAS0400MB
MAS0400LB
MAE0410MB
MAS0410MB
MAS0410LB
(mm)
3.0
3.65
4.1
(l/d)
Hole
DC Depth
Ext.
3
6
Int.
Int.
Ext.
4.3
3
3
6
Int.
Int.
4
4
4
Ext.
4.4
3
3
6
Int.
Int.
0.6
0.6
0.6
4
4
4
3
3
6
Ext.
4.5
Int.
Int.
64
64
74
0.6
0.6
0.6
4
4
4
Ext.
4.6
3
3
6
Int.
Int.
24.6 64.6
24.6 64.6
34.6 74.6
64
64
74
0.6
0.6
0.6
4
4
4
3
3
6
Ext.
4.7
Int.
Int.
28.7 68.7
28.7 68.7
40.7 80.7
68
68
80
0.7
0.7
0.7
4
4
4
Ext.
4.8
3
3
6
Int.
Int.
28.7 68.7
28.7 68.7
40.7 80.7
68
68
80
0.7
0.7
0.7
4
4
4
Ext.
4.9
3
3
6
Int.
Int.
28.7 68.7
28.7 68.7
40.7 80.7
68
68
80
0.7
0.7
0.7
4
4
4
Ext.
5.0
3
3
6
Int.
Int.
28.7 68.7
28.7 68.7
40.7 80.7
68
68
80
0.7
0.7
0.7
4
4
4
Ext.
5.1
3
3
6
Int.
Int.
28.7 68.7
28.7 68.7
40.7 80.7
68
68
80
0.7
0.7
0.7
4
4
4
3
3
6
Ext.
5.2
Int.
Int.
28.7 68.7
28.7 68.7
40.7 80.7
68
68
80
0.7
0.7
0.7
4
4
4
Ext.
5.3
3
3
6
Int.
Int.
31.7 71.7
31.7 71.7
44.7 84.7
71
71
84
0.7
0.7
0.7
5
5
5
3
3
6
Ext.
5.4
Int.
Int.
MAE0420MB
MAS0420MB
MAS0420LB
MAE0430MB
MAS0430MB
MAS0430LB
MAE0440MB
MAS0440MB
MAS0440LB
MAE0450MB
MAS0450MB
MAS0450LB
MAE0460MB
MAS0460MB
MAS0460LB
MAE0470MB
MAS0470MB
MAS0470LB
MAE0480MB
MAS0480MB
MAS0480LB
MAE0490MB
MAS0490MB
MAS0490LB
MAE0500MB
MAS0500MB
MAS0500LB
MAE0510MB
MAS0510MB
MAS0510LB
MAE0520MB
MAS0520MB
MAS0520LB
MAE0530MB
MAS0530MB
MAS0530LB
MAE0540MB
MAS0540MB
MAS0540LB
PL DCON
(mm)
*
*
*
Dimensions (mm)
Order Number
LCF OAL LF
21.5 61.5
21.5 61.5
30.5 70.5
61
61
70
0.5
0.5
0.5
3
3
3
24.6 64.6
24.6 64.6
34.6 74.6
64
64
74
0.6
0.6
0.6
4
4
4
24.6 64.6
24.6 64.6
34.6 74.6
64
64
74
0.6
0.6
0.6
24.6 64.6
24.6 64.6
34.6 74.6
64
64
74
24.6 64.6
24.6 64.6
34.6 74.6
4.2
(l/d)
OAL
Stock
HTi10
Order Number
OAL
LF
LCF
Coolant
(Int./Ext.)
Dimensions (mm)
Stock
HTi10
Coolant
(Int./Ext.)
(Note 1) MAS type bigger than & 5.0 have a recess in the end face.
(Note 2) MAE/MAS drills are suitable for use with shrink fit holders.
Hole
DC Depth
LF
*
*
*
LCF OAL LF
PL DCON
31.8 71.8
71
0.8
31.8 71.8
44.8 84.8
71
84
0.8
0.8
5
5
31.8 71.8
31.8 71.8
44.8 84.8
71
71
84
0.8
0.8
0.8
5
5
5
31.8 71.8
31.8 71.8
44.8 84.8
71
71
84
0.8
0.8
0.8
5
5
5
31.8 71.8
31.8 71.8
44.8 84.8
71
71
84
0.8
0.8
0.8
5
5
5
33.8 73.8
33.8 73.8
48.8 88.8
73
73
88
0.8
0.8
0.8
5
5
5
33.9 73.9
33.9 73.9
48.9 88.9
73
73
88
0.9
0.9
0.9
5
5
5
33.9 73.9
33.9 73.9
48.9 88.9
73
73
88
0.9
0.9
0.9
5
5
5
33.9 73.9
33.9 73.9
48.9 88.9
73
73
88
0.9
0.9
0.9
5
5
5
33.9 73.9
33.9 73.9
48.9 88.9
73
73
88
0.9
0.9
0.9
5
5
5
36.9 76.9
36.9 76.9
52.9 92.9
76
76
92
0.9
0.9
0.9
6
6
6
36.9 76.9
36.9 76.9
52.9 92.9
76
76
92
0.9
0.9
0.9
6
6
6
37.0 77.0
37.0 77.0
53.0 93.0
76
76
92
1.0
1.0
1.0
6
6
6
37.0 77.0
37.0 77.0
53.0 93.0
76
76
92
1.0
1.0
1.0
6
6
6
DRILLING
DCON(h6)
140
140
CARBIDE
DCON(h6)
MAE/MAS
aSpecially for aluminium and cast iron drilling.

aHigh hole accuracy.
aPre-hole drilling for roll taps.
aHelical through coolant hole enables high speed machining (MAS type).
* Standard hole size for rolled thread taps.

CUTTING CONDITIONS
TECHNICAL DATA
N134
Q001
N129
Ext.
3
6
Int.
Int.
3
3
6
Ext.
5.6
Int.
Int.
Ext.
5.7
3
3
6
Int.
Int.
3
3
6
Ext.
Int.
Int.
3
3
6
Ext.
5.5
5.8
Int.
Int.
3
3
6
Ext.
Int.
Int.
Ext.
6.1
3
3
6
Int.
Int.
Ext.
6.2
3
3
6
Int.
Int.
3
3
6
Ext.
6.3
Int.
Int.
Ext.
6.4
3
3
6
Int.
Int.
3
3
6
Ext.
Int.
Int.
3
3
6
Ext.
Int.
Int.
3
3
6
Ext.
Int.
Int.
Ext.
6.8
3
3
6
Int.
Int.
Ext.
6.9
3
3
6
Int.
Int.
3
3
6
Ext.
Int.
Int.
5.9
6.0
6.5
6.6
6.7
DRILLING
(l/d)
7.0
Order Number
LCF OAL LF
Hole
DC Depth
Order Number
3
3
6
Ext.
Int.
Int.
3
3
6
Ext.
7.2
Int.
Int.
6
6
6
Ext.
7.3
3
3
6
Int.
Int.
6
6
6
3
3
6
Ext.
7.35
Int.
Int.
Ext.
7.4
3
3
6
Int.
Int.
Ext.
7.5
3
3
6
Int.
Int.
Ext.
7.6
3
3
6
Int.
Int.
3
3
6
Ext.
Int.
Int.
MAE0710MB
MAS0710MB
MAS0710LB
MAE0720MB
MAS0720MB
MAS0720LB
MAE0730MB
MAS0730MB
MAS0730LB
MAE0735MB
MAS0735MB
MAS0735LB
MAE0740MB
MAS0740MB
MAS0740LB
MAE0750MB
MAS0750MB
MAS0750LB
MAE0760MB
MAS0760MB
MAS0760LB
MAE0770MB
MAS0770MB
MAS0770LB
MAE0780MB
MAS0780MB
MAS0780LB
MAE0790MB
MAS0790MB
MAS0790LB
MAE0800MB
MAS0800MB
MAS0800LB
MAE0810MB
MAS0810MB
MAS0810LB
MAE0820MB
MAS0820MB
MAS0820LB
MAE0830MB
MAS0830MB
MAS0830LB
MAE0840MB
MAS0840MB
MAS0840LB
MAE0850MB
MAS0850MB
MAS0850LB
PL DCON
(mm)
* MAE0550MB
* MAS0550MB
* MAS0550LB
MAE0560MB
MAS0560MB
MAS0560LB
MAE0570MB
MAS0570MB
MAS0570LB
MAE0580MB
MAS0580MB
MAS0580LB
MAE0590MB
MAS0590MB
MAS0590LB
MAE0600MB
MAS0600MB
MAS0600LB
MAE0610MB
MAS0610MB
MAS0610LB
MAE0620MB
MAS0620MB
MAS0620LB
MAE0630MB
MAS0630MB
MAS0630LB
MAE0640MB
MAS0640MB
MAS0640LB
MAE0650MB
MAS0650MB
MAS0650LB
MAE0660MB
MAS0660MB
MAS0660LB
MAE0670MB
MAS0670MB
MAS0670LB
MAE0680MB
MAS0680MB
MAS0680LB
MAE0690MB
MAS0690MB
MAS0690LB
MAE0700MB
MAS0700MB
MAS0700LB
37.0 77.0
76
1.0
37.0 77.0
53.0 93.0
76
92
1.0
1.0
6
6
40.0 80.0
40.0 80.0
58.0 98.0
79
79
97
1.0
1.0
1.0
6
6
6
40.0 80.0
40.0 80.0
58.0 98.0
79
79
97
1.0
1.0
1.0
40.1 80.1
40.1 80.1
58.1 98.1
79
79
97
1.1
1.1
1.1
7.1
(l/d)
40.1 80.1
40.1 80.1
58.1 98.1
79
79
97
1.1
1.1
1.1
6
6
6
40.1 80.1
40.1 80.1
58.1 98.1
79
79
97
1.1
1.1
1.1
6
6
6
43.1 85.1 84
43.1 85.1 84
63.1 105.1 104
1.1
1.1
1.1
7
7
7
43.1 85.1 84
43.1 85.1 84
63.1 105.1 104
1.1
1.1
1.1
7
7
7
7.7
43.1 85.1 84
43.1 85.1 84
63.1 105.1 104
1.1
1.1
1.1
7
7
7
3
3
6
Ext.
7.8
Int.
Int.
43.2 85.2 84
43.2 85.2 84
63.2 105.2 104
1.2
1.2
1.2
7
7
7
Ext.
7.9
3
3
6
Int.
Int.
43.2 85.2 84
43.2 85.2 84
63.2 105.2 104
1.2
1.2
1.2
7
7
7
3
3
6
Ext.
8.0
Int.
Int.
Ext.
8.1
3
3
6
Int.
Int.
Ext.
8.2
3
3
6
Int.
Int.
Ext.
8.3
3
3
6
Int.
Int.
3
3
6
Ext.
Int.
Int.
3
3
6
Ext.
Int.
Int.
43.2 85.2 84
43.2 85.2 84
66.2 108.2 107
1.2
1.2
1.2
7
7
7
43.2 85.2 84
43.2 85.2 84
66.2 108.2 107
1.2
1.2
1.2
7
7
7
43.2 85.2 84
43.2 85.2 84
66.2 108.2 107
1.2
1.2
1.2
7
7
7
43.3 85.3 84
43.3 85.3 84
66.3 108.3 107
1.3
1.3
1.3
7
7
7
8.4
43.3 85.3 84
43.3 85.3 84
66.3 108.3 107
1.3
1.3
1.3
7
7
7
8.5
N130
Dimensions (mm)
Stock
HTi10
(mm)
Dimensions (mm)
Stock
HTi10
Hole
DC Depth
Coolant
(Int./Ext.)
MAE/MAS
Coolant
(Int./Ext.)
CARBIDE
*
*
*
LCF OAL LF
PL DCON
49.3 91.3 90
49.3 91.3 90
69.3 111.3 110
1.3
1.3
1.3
8
8
8
49.3 91.3 90
49.3 91.3 90
69.3 111.3 110
1.3
1.3
1.3
8
8
8
49.3 91.3 90
49.3 91.3 90
69.3 111.3 110
1.3
1.3
1.3
8
8
8
49.3 91.3 90
49.3 91.3 90
69.3 111.3 110
1.3
1.3
1.3
8
8
8
49.3 91.3 90
49.3 91.3 90
69.3 111.3 110
1.3
1.3
1.3
8
8
8
49.4 91.4 90
49.4 91.4 90
69.4 111.4 110
1.4
1.4
1.4
8
8
8
49.4 91.4 90
49.4 91.4 90
73.4 115.4 114
1.4
1.4
1.4
8
8
8
49.4 91.4 90
49.4 91.4 90
73.4 115.4 114
1.4
1.4
1.4
8
8
8
49.4 91.4 90
49.4 91.4 90
73.4 115.4 114
1.4
1.4
1.4
8
8
8
49.4 91.4 90
49.4 91.4 90
73.4 115.4 114
1.4
1.4
1.4
8
8
8
49.5 91.5 90
49.5 91.5 90
73.5 115.5 114
1.5
1.5
1.5
8
8
8
51.5 95.5 94
51.5 95.5 94
76.5 120.5 119
1.5
1.5
1.5
9
9
9
51.5 95.5 94
51.5 95.5 94
76.5 120.5 119
1.5
1.5
1.5
9
9
9
51.5 95.5 94
51.5 95.5 94
76.5 120.5 119
1.5
1.5
1.5
9
9
9
51.5 95.5 94
51.5 95.5 94
76.5 120.5 119
1.5
1.5
1.5
9
9
9
51.5 95.5 94
51.5 95.5 94
76.5 120.5 119
1.5
1.5
1.5
9
9
9
(l/d)
3
3
6
Ext.
8.6
Int.
Int.
3
3
6
Ext.
8.7
Int.
Int.
Ext.
8.8
3
3
6
Int.
Int.
3
3
6
Ext.
8.9
Int.
Int.
Ext.
9.0
3
3
6
Int.
Int.
3
3
6
Ext.
Int.
Int.
3
3
6
Ext.
Int.
Int.
3
9.21 3
6
Ext.
Int.
Int.
3
3
6
Ext.
9.3
Int.
Int.
Ext.
9.4
3
3
6
Int.
Int.
3
3
6
Ext.
9.5
Int.
Int.
Ext.
9.6
3
3
6
Int.
Int.
3
3
6
Ext.
Int.
Int.
Ext.
9.8
3
3
6
Int.
Int.
Ext.
9.9
3
3
6
Int.
Int.
3
3
6
Ext.
Int.
Int.
MAE0860MB
MAS0860MB
MAS0860LB
MAE0870MB
MAS0870MB
MAS0870LB
MAE0880MB
MAS0880MB
MAS0880LB
MAE0890MB
MAS0890MB
MAS0890LB
MAE0900MB
MAS0900MB
MAS0900LB
MAE0910MB
MAS0910MB
MAS0910LB
MAE0920MB
MAS0920MB
MAS0920LB
MAE0921MB
MAS0921MB
MAS0921LB
MAE0930MB
MAS0930MB
MAS0930LB
MAE0940MB
MAS0940MB
MAS0940LB
MAE0950MB
MAS0950MB
MAS0950LB
MAE0960MB
MAS0960MB
MAS0960LB
MAE0970MB
MAS0970MB
MAS0970LB
MAE0980MB
MAS0980MB
MAS0980LB
MAE0990MB
MAS0990MB
MAS0990LB
MAE1000MB
MAS1000MB
MAS1000LB
9.1
9.2
9.7
10.0
Order Number
3
3
6
Ext.
Int.
Int.
3
3
6
Ext.
10.2
Int.
Int.
9
9
9
Ext.
10.3
3
3
6
Int.
Int.
1.6
1.6
1.6
9
9
9
3
3
6
Ext.
10.4
Int.
Int.
51.6 95.6 94
51.6 95.6 94
78.6 122.6 121
1.6
1.6
1.6
9
9
9
Ext.
10.5
3
3
6
Int.
Int.
54.7 98.7 97
54.7 98.7 97
82.7 126.7 125
1.7
1.7
1.7
10
10
10
Ext.
10.6
3
3
6
Int.
Int.
54.7 98.7 97
54.7 98.7 97
82.7 126.7 125
1.7
1.7
1.7
10
10
10
Ext.
10.7
3
3
6
Int.
Int.
54.7 98.7 97
54.7 98.7 97
82.7 126.7 125
1.7
1.7
1.7
10
10
10
Ext.
10.8
3
3
6
Int.
Int.
54.7 98.7 97
54.7 98.7 97
82.7 126.7 125
1.7
1.7
1.7
10
10
10
3
3
6
Ext.
10.9
Int.
Int.
54.7 98.7 97
54.7 98.7 97
82.7 126.7 125
1.7
1.7
1.7
10
10
10
Ext.
11.0
3
3
6
Int.
Int.
54.7 98.7 97
54.7 98.7 97
82.7 126.7 125
1.7
1.7
1.7
10
10
10
Ext.
11.08 3
Int.
Int.
54.7 98.7 97
54.7 98.7 97
82.7 126.7 125
1.7
1.7
1.7
10
10
10
Ext.
11.1
3
3
6
Int.
Int.
54.8 98.8 97
54.8 98.8 97
82.8 126.8 125
1.8
1.8
1.8
10
10
10
Ext.
11.2
3
3
6
Int.
Int.
54.8 98.8 97
54.8 98.8 97
82.8 126.8 125
1.8
1.8
1.8
10
10
10
Ext.
11.3
3
3
6
Int.
Int.
54.8 98.8 97
54.8 98.8 97
82.8 126.8 125
1.8
1.8
1.8
10
10
10
Ext.
11.4
3
3
6
Int.
Int.
54.8 98.8 97
54.8 98.8 97
82.8 126.8 125
1.8
1.8
1.8
10
10
10
3
3
6
Ext.
11.5
Int.
Int.
MAE1010MB
MAS1010MB
MAS1010LB
MAE1020MB
MAS1020MB
MAS1020LB
MAE1030MB
MAS1030MB
MAS1030LB
MAE1040MB
MAS1040MB
MAS1040LB
MAE1050MB
MAS1050MB
MAS1050LB
MAE1060MB
MAS1060MB
MAS1060LB
MAE1070MB
MAS1070MB
MAS1070LB
MAE1080MB
MAS1080MB
MAS1080LB
MAE1090MB
MAS1090MB
MAS1090LB
MAE1100MB
MAS1100MB
MAS1100LB
MAE1108MB
MAS1108MB
MAS1108LB
MAE1110MB
MAS1110MB
MAS1110LB
MAE1120MB
MAS1120MB
MAS1120LB
MAE1130MB
MAS1130MB
MAS1130LB
MAE1140MB
MAS1140MB
MAS1140LB
MAE1150MB
MAS1150MB
MAS1150LB
LCF OAL LF
PL DCON
(mm)
*
*
*
51.6 95.6 94
51.6 95.6 94
78.6 122.6 121
1.6
1.6
1.6
9
9
9
10.1
51.6 95.6 94
51.6 95.6 94
78.6 122.6 121
1.6
1.6
1.6
9
9
9
51.6 95.6 94
51.6 95.6 94
78.6 122.6 121
1.6
1.6
1.6
51.6 95.6 94
51.6 95.6 94
78.6 122.6 121
(l/d)
*
*
*
LCF OAL LF
PL DCON
56.8 102.8 101

56.8 102.8 101
90.8 136.8 135
1.8
1.8
1.8
11
11
11
56.9 102.9 101

56.9 102.9 101
90.9 136.9 135
1.9
1.9
1.9
11
11
11
56.9 102.9 101

56.9 102.9 101
90.9 136.9 135
1.9
1.9
1.9
11
11
11
56.9 102.9 101

56.9 102.9 101
90.9 136.9 135
1.9
1.9
1.9
11
11
11
56.9 102.9 101

56.9 102.9 101
90.9 136.9 135
1.9
1.9
1.9
11
11
11
56.9 102.9 101

56.9 102.9 101
90.9 136.9 135
1.9
1.9
1.9
11
11
11
56.9 102.9 101

56.9 102.9 101
90.9 136.9 135
1.9
1.9
1.9
11
11
11
57.0 103.0 101

57.0 103.0 101
91.0 137.0 135
2.0
2.0
2.0
11
11
11
57.0 103.0 101

57.0 103.0 101
91.0 137.0 135
2.0
2.0
2.0
11
11
11
57.0 103.0 101

57.0 103.0 101
91.0 137.0 135
2.0
2.0
2.0
11
11
11
62.0 108.0 106

62.0 108.0 106
96.0 142.0 140
2.0
2.0
2.0
12
12
12
62.0 108.0 106

62.0 108.0 106
96.0 142.0 140
2.0
2.0
2.0
12
12
12
62.0 108.0 106

62.0 108.0 106
96.0 142.0 140
2.0
2.0
2.0
12
12
12
62.1 108.1 106

62.1 108.1 106
96.1 142.1 140
2.1
2.1
2.1
12
12
12
62.1 108.1 106

62.1 108.1 106
96.1 142.1 140
2.1
2.1
2.1
12
12
12
62.1 108.1 106

62.1 108.1 106
96.1 142.1 140
2.1
2.1
2.1
12
12
12
DRILLING
(mm)
Dimensions (mm)
Stock
HTi10
Order Number
Hole
DC Depth
Coolant
(Int./Ext.)
Dimensions (mm)
Stock
HTi10
Hole
DC Depth
Coolant
(Int./Ext.)
CARBIDE
CUTTING CONDITIONS
TECHNICAL DATA
N134
Q001
N131
3
3
6
Ext.
Int.
Int.
3
3
6
Ext.
11.7
Int.
Int.
Ext.
11.8
3
3
6
Int.
Int.
3
3
6
Ext.
11.9
Int.
Int.
Ext.
12.0
3
3
6
Int.
Int.
3
3
6
Ext.
Int.
Int.
Ext.
12.2
3
3
6
Int.
Int.
Ext.
12.3
3
3
6
Int.
Int.
3
3
6
Ext.
12.4
Int.
Int.
Ext.
12.5
3
3
6
Int.
Int.
3
3
6
Ext.
12.6
Int.
Int.
Ext.
12.7
3
3
6
Int.
Int.
3
3
6
Ext.
Int.
Int.
3
3
6
Ext.
Int.
Int.
3
12.96 3
6
Ext.
Int.
Int.
3
3
6
Ext.
Int.
Int.
MAE1160MB
MAS1160MB
MAS1160LB
MAE1170MB
MAS1170MB
MAS1170LB
MAE1180MB
MAS1180MB
MAS1180LB
MAE1190MB
MAS1190MB
MAS1190LB
MAE1200MB
MAS1200MB
MAS1200LB
MAE1210MB
MAS1210MB
MAS1210LB
MAE1220MB
MAS1220MB
MAS1220LB
MAE1230MB
MAS1230MB
MAS1230LB
MAE1240MB
MAS1240MB
MAS1240LB
MAE1250MB
MAS1250MB
MAS1250LB
MAE1260MB
MAS1260MB
MAS1260LB
MAE1270MB
MAS1270MB
MAS1270LB
MAE1280MB
MAS1280MB
MAS1280LB
MAE1290MB
MAS1290MB
MAS1290LB
MAE1296MB
MAS1296MB
MAS1296LB
MAE1300MB
MAS1300MB
MAS1300LB
11.6
12.1
12.8
12.9
13.0
(l/d)
*
*
*
LCF OAL LF
Hole
DC Depth
Order Number
(mm)
(l/d)
3
3
6
Ext.
Int.
Int.
MAE1310MB
MAS1310MB
MAS1310LB
MAE1320MB
MAS1320MB
MAS1320LB
MAE1330MB
MAS1330MB
MAS1330LB
MAE1340MB
MAS1340MB
MAS1340LB
MAE1350MB
MAS1350MB
MAS1350LB
MAE1360MB
MAS1360MB
MAS1360LB
MAE1370MB
MAS1370MB
MAS1370LB
MAE1380MB
MAS1380MB
MAS1380LB
MAE1390MB
MAS1390MB
MAS1390LB
MAE1400MB
MAS1400MB
MAS1400LB
MAE1410MB
MAS1410MB
MAS1410LB
MAE1420MB
MAS1420MB
MAS1420LB
MAE1430MB
MAS1430MB
MAS1430LB
MAE1440MB
MAS1440MB
MAS1440LB
MAE1450MB
MAS1450MB
MAS1450LB
MAE1460MB
MAS1460MB
MAS1460LB
PL DCON
62.1 108.1 106

62.1 108.1 106
96.1 142.1 140
2.1
2.1
2.1
12
12
12
13.1
62.1 108.1 106

62.1 108.1 106
96.1 142.1 140
2.1
2.1
2.1
12
12
12
3
3
6
Ext.
13.2
Int.
Int.
62.1 108.1 106

62.1 108.1 106
96.1 142.1 140
2.1
2.1
2.1
12
12
12
Ext.
13.3
3
3
6
Int.
Int.
62.2 108.2 106

62.2 108.2 106
96.2 142.2 140
2.2
2.2
2.2
12
12
12
3
3
6
Ext.
13.4
Int.
Int.
62.2 108.2 106

62.2 108.2 106
96.2 142.2 140
2.2
2.2
2.2
12
12
12
Ext.
13.5
3
3
6
Int.
Int.
67.2 117.2 115

67.2 117.2 115
102.2 152.2 150
2.2
2.2
2.2
13
13
13
Ext.
13.6
3
3
6
Int.
Int.
67.2 117.2 115

67.2 117.2 115
102.2 152.2 150
2.2
2.2
2.2
13
13
13
Ext.
13.7
3
3
6
Int.
Int.
67.2 117.2 115

67.2 117.2 115
102.2 152.2 150
2.2
2.2
2.2
13
13
13
Ext.
13.8
3
3
6
Int.
Int.
67.3 117.3 115

67.3 117.3 115
102.3 152.3 150
2.3
2.3
2.3
13
13
13
3
3
6
Ext.
13.9
Int.
Int.
67.3 117.3 115

67.3 117.3 115
102.3 152.3 150
2.3
2.3
2.3
13
13
13
Ext.
14.0
3
3
6
Int.
Int.
67.3 117.3 115

67.3 117.3 115
102.3 152.3 150
2.3
2.3
2.3
13
13
13
3
3
6
Ext.
14.1
Int.
Int.
67.3 117.3 115

67.3 117.3 115
102.3 152.3 150
2.3
2.3
2.3
13
13
13
Ext.
14.2
3
3
6
Int.
Int.
67.3 117.3 115

67.3 117.3 115
102.3 152.3 150
2.3
2.3
2.3
13
13
13
Ext.
14.3
3
3
6
Int.
Int.
67.3 117.3 115

67.3 117.3 115
102.3 152.3 150
2.3
2.3
2.3
13
13
13
Ext.
14.4
3
3
6
Int.
Int.
67.4 117.4 115

67.4 117.4 115
102.4 152.4 150
2.4
2.4
2.4
13
13
13
Ext.
14.5
3
3
6
Int.
Int.
67.4 117.4 115

67.4 117.4 115
102.4 152.4 150
2.4
2.4
2.4
13
13
13
3
3
6
Ext.
14.6
Int.
Int.
N132
Dimensions (mm)
Stock
HTi10
Order Number
(mm)
DRILLING
Dimensions (mm)
Stock
HTi10
Hole
DC Depth
Coolant
(Int./Ext.)
MAE/MAS
Coolant
(Int./Ext.)
CARBIDE
LCF OAL LF
PL DCON
72.4 122.4 120

72.4 122.4 120
112.4 162.4 160
2.4
2.4
2.4
14
14
14
72.4 122.4 120

72.4 122.4 120
112.4 162.4 160
2.4
2.4
2.4
14
14
14
72.4 122.4 120

72.4 122.4 120
112.4 162.4 160
2.4
2.4
2.4
14
14
14
72.4 122.4 120

72.4 122.4 120
112.4 162.4 160
2.4
2.4
2.4
14
14
14
72.5 122.5 120

72.5 122.5 120
112.5 162.5 160
2.5
2.5
2.5
14
14
14
72.5 122.5 120

72.5 122.5 120
112.5 162.5 160
2.5
2.5
2.5
14
14
14
72.5 122.5 120

72.5 122.5 120
112.5 162.5 160
2.5
2.5
2.5
14
14
14
72.5 122.5 120

72.5 122.5 120
112.5 162.5 160
2.5
2.5
2.5
14
14
14
72.5 122.5 120

72.5 122.5 120
112.5 162.5 160
2.5
2.5
2.5
14
14
14
72.5 122.5 120

72.5 122.5 120
112.5 162.5 160
2.5
2.5
2.5
14
14
14
74.6 132.6 130

74.6 132.6 130
117.6 175.6 173
2.6
2.6
2.6
15
15
15
74.6 132.6 130

74.6 132.6 130
117.6 175.6 173
2.6
2.6
2.6
15
15
15
74.6 132.6 130

74.6 132.6 130
117.6 175.6 173
2.6
2.6
2.6
15
15
15
74.6 132.6 130

74.6 132.6 130
117.6 175.6 173
2.6
2.6
2.6
15
15
15
74.6 132.6 130

74.6 132.6 130
117.6 175.6 173
2.6
2.6
2.6
15
15
15
74.7 132.7 130

74.7 132.7 130
117.7 175.7 173
2.7
2.7
2.7
15
15
15
(l/d)
Order Number
3
3
6
Ext.
Int.
Int.
3
3
6
Ext.
14.8
Int.
Int.
Ext.
14.9
3
3
6
Int.
Int.
Ext.
14.96 3
Int.
Int.
Ext.
15.0
3
3
6
Int.
Int.
Ext.
15.1
3
3
6
Int.
Int.
Ext.
15.2
3
3
6
Int.
Int.
Ext.
15.3
3
3
6
Int.
Int.
3
3
6
Ext.
15.4
Int.
Int.
Ext.
15.5
3
3
6
Int.
Int.
3
3
6
Ext.
15.6
Int.
Int.
Ext.
15.7
3
3
6
Int.
Int.
Ext.
15.8
3
3
6
Int.
Int.
Ext.
15.9
3
3
6
Int.
Int.
Ext.
16.0
3
3
6
Int.
Int.
MAE1470MB
MAS1470MB
MAS1470LB
MAE1480MB
MAS1480MB
MAS1480LB
MAE1490MB
MAS1490MB
MAS1490LB
MAE1496MB
MAS1496MB
MAS1496LB
MAE1500MB
MAS1500MB
MAS1500LB
MAE1510MB
MAS1510MB
MAS1510LB
MAE1520MB
MAS1520MB
MAS1520LB
MAE1530MB
MAS1530MB
MAS1530LB
MAE1540MB
MAS1540MB
MAS1540LB
MAE1550MB
MAS1550MB
MAS1550LB
MAE1560MB
MAS1560MB
MAS1560LB
MAE1570MB
MAS1570MB
MAS1570LB
MAE1580MB
MAS1580MB
MAS1580LB
MAE1590MB
MAS1590MB
MAS1590LB
MAE1600MB
MAS1600MB
MAS1600LB
14.7
*
*
*
LCF OAL LF
PL DCON
74.7 132.7 130

74.7 132.7 130
117.7 175.7 173
2.7
2.7
2.7
15
15
15
74.7 132.7 130

74.7 132.7 130
117.7 175.7 173
2.7
2.7
2.7
15
15
15
74.7 132.7 130

74.7 132.7 130
117.7 175.7 173
2.7
2.7
2.7
15
15
15
74.7 132.7 130

74.7 132.7 130
117.7 175.7 173
2.7
2.7
2.7
15
15
15
74.7 132.7 130

74.7 132.7 130
117.7 175.7 173
2.7
2.7
2.7
15
15
15
78.7 136.7 134

78.7 136.7 134
122.7 180.7 178
2.7
2.7
2.7
16
16
16
78.8 136.8 134

78.8 136.8 134
122.8 180.8 178
2.8
2.8
2.8
16
16
16
78.8 136.8 134

78.8 136.8 134
122.8 180.8 178
2.8
2.8
2.8
16
16
16
78.8 136.8 134

78.8 136.8 134
122.8 180.8 178
2.8
2.8
2.8
16
16
16
78.8 136.8 134

78.8 136.8 134
122.8 180.8 178
2.8
2.8
2.8
16
16
16
78.8 136.8 134

78.8 136.8 134
122.8 180.8 178
2.8
2.8
2.8
16
16
16
78.9 136.9 134

78.9 136.9 134
122.9 180.9 178
2.9
2.9
2.9
16
16
16
78.9 136.9 134

78.9 136.9 134
122.9 180.9 178
2.9
2.9
2.9
16
16
16
78.9 136.9 134

78.9 136.9 134
122.9 180.9 178
2.9
2.9
2.9
16
16
16
78.9 136.9 134

78.9 136.9 134
122.9 180.9 178
2.9
2.9
2.9
16
16
16
DRILLING
(mm)
Dimensions (mm)
Stock
HTi10
DC
Hole
Depth
Coolant
(Int./Ext.)
CARBIDE
CUTTING CONDITIONS
TECHNICAL DATA
N134
Q001
N133
CARBIDE
MAE/MAS
Type
M
A
E
M
A
S
Drill Dia. &3.0 &6.0
Work Material
Drill Dia. &6.1 &10.0

Feed (mm/rev)
Drill Dia. &10.1 &16.0
Feed (mm/rev)
Feed (mm/rev)
N Aluminium Alloy Casting
90 (40 140)
0.15 (0.05 0.3)
100 (50 150)
0.2 (0.1 0.3)
120 (60 170)
0.25 (0.1 0.4)
Aluminium Alloy Die Casting
100 (60 150)
0.12 (0.05 0.25)
110 (70 160)
0.15 (0.05 0.25)
130 (80 180)
0.2 (0.1 0.3)
80 (60 100)
0.3 (0.2 0.4)
60 (40 80)
0.2 (0.1 0.3)
Gray Cast Iron
40 (20 60)
0.15 (0.1 0.2)
60 (40 80)
0.2 (0.1 0.3)
Ductile Cast Iron
30 (20 40)
0.1 (0.05 0.15)
40 (20 60)
0.12 (0.05 0.2)
N Aluminium Alloy Casting
100 (60 150)
0.15 (0.05 0.3)
120 (80 170)
0.2 (0.1 0.3)
150 (100 200)
0.25 (0.1 0.4)
Aluminium Alloy Die Casting
120 (80 170)
0.12 (0.05 0.25)
150 (100 180)
0.15 (0.05 0.25)
160 (120 200)
0.2 (0.1 0.3)
0.2 (0.1 0.3)
100 (70 130)
0.3 (0.2 0.4)
0.12 (0.05 0.2)
80 (60 100)
0.2 (0.1 0.3)
Gray Cast Iron
60 (40 80)
0.15 (0.1 0.2)
80 (60 110)
Ductile Cast Iron
45 (30 60)
0.1 (0.05 0.15)
60 (40 80)
y HOLE AND DRILL DIAMETERS FOR THREAD TAPPING

Thread Tapping
Thread Size
Drill Diameter
(DC)
M4x0.7
3.3
Rolled Thread Tapping
Hole Diameter Tolerance
Hole Diameter Tolerance
Drill Diameter
(DC)
max.
min.
max.
min.
3.242
3.422
3.65
3.65
3.70
M5x0.8
4.2
4.134
4.334
4.60
4.59
4.66
M6x1.0
5.0
4.917
5.153
5.50
5.48
5.57
6.8
6.647
6.912
7.35
7.34
7.41
M10x1.5
M8x1.25
8.5
8.376
8.676
9.21
9.18
9.28
M12x1.75
10.3
10.106
10.441
11.08
11.05
11.15
M14x2
12.0
11.835
12.210
12.96
12.92
13.04
M16x2
14.0
13.835
14.210
14.96
14.92
15.04
Workpiece : JIS AC4B-T6 Drilled Depth : l/d=3(Through Hole) Cutting Speed : 100m/min WSO (10%)
f=0
m/rev
f=0.2m
f=0.15mm/rev
250
re
v
m/
5m
1000
/rev
mm
.2
f=0
/rev
5mm
f=0.1
500
0
8
12
16
4
Drill Diameter (mm)
mm
.25
500
v
/re
8
12
16
4
Drill Diameter (mm)
8
12
16
4
Drill Diameter (mm)
y MACHINED HOLE ACCURACY
Tool : MAS1100MB Workpiece : JIS AC4B-T6 Feed : 0.35mm/rev Drilled Depth : 33mm WSO (10%)
Surface Roughness
Oversize
Surface Roughness (!m)
Oversize (!m)
30
20
10
40
120
150
200
Roundness
12
12
Roundness (!m)
DRILLING
1500
f=0.15mm/rev
0
N134
750
f=
0.2
v
/re
mm
5
2
.
f=0
/rev
2mm
f=0.
Thrust
Thrust (N)
Torque
Torque (N cm)
Power Consumption
40
120
150
200
40
120
150
200
HSS MILLING SHANK DRILLS
SEPDM
SE High Precision Drill (M)
P
Steel
CO HSS
D-STH
NEW
118
135
Thinning
DC<4
HSS
DC=4
0.5 < DC < 3 3.1 < DC < 4
0
0.006
Stainless Steel Cast Iron Non-ferrous Metal

PL
0
0.008
DCON(h7)
DC
LF
LCF
OAL
a Unique D-STH process dramatically improves sharpness and welding
resistance and smooth chip discharge.
0.50 6.15 50.15 50

0.55 6.17 50.17 50
0.15
0.17
3
3
SEPDMD0400
0.60 8.18 50.18 50
0.18
0.65 8.20 50.20 50
0.20
0.70 10.21 50.21 50
0.21
0.75 10.23 50.23 50
0.23
0.80 10.24 50.24 50
0.24
0.85 10.26 50.26 50
0.26
0.90 12.27 50.27 50
0.27
0.95 12.29 50.29 50
0.29
1.0 12.3 60.3
60
0.3
1.1 16.3 60.3
60
0.3
1.2 16.4 60.4
60
0.4
1.3 16.4 60.4
60
0.4
1.4 18.4 60.4
60
0.4
1.5 18.5 60.5
60
0.5
1.6 20.5 60.5
60
0.5
1.7 20.5 60.5
60
0.5
1.8 22.5 60.5
60
0.5
1.9 22.6 60.6
60
0.6
2.0 23.6 70.6
70
0.6
2.1 23.6 70.6
70
0.6
2.2 26.7 70.7
70
0.7
2.3 26.7 70.7
70
0.7
2.4 29.7 70.7
70
0.7
2.5 29.8 70.8
70
0.8
2.6 29.8 70.8
70
0.8
2.7 32.8 70.8
70
0.8
2.8 32.8 70.8
70
0.8
2.9 32.9 70.9
70
0.9
3.0 32.9 70.9
70
0.9
3.1 35.9 85.9
85
0.9
3.2 36.0 86.0
85
1.0
3.3 36.0 86.0
85
1.0
3.4 39.0 86.0
85
1.0
3.5 39.1 86.1
85
1.1
3.6 39.1 86.1
85
1.1
3.7 39.1 86.1
85
1.1
3.8 43.1 86.1

3.9 43.2 86.2
85
85
1.1
1.2
4
4
LCF OAL
LF
PL DCON
DC
LCF OAL
LF
PL DCON
4.0 42.8 85.8
85
0.8
DRILLING
SEPDMD0050
SEPDMD0055
SEPDMD0060
SEPDMD0065
SEPDMD0070
SEPDMD0075
SEPDMD0080
SEPDMD0085
SEPDMD0090
SEPDMD0095
SEPDMD0100
SEPDMD0110
SEPDMD0120
SEPDMD0130
SEPDMD0140
SEPDMD0150
SEPDMD0160
SEPDMD0170
SEPDMD0180
SEPDMD0190
SEPDMD0200
SEPDMD0210
SEPDMD0220
SEPDMD0230
SEPDMD0240
SEPDMD0250
SEPDMD0260
SEPDMD0270
SEPDMD0280
SEPDMD0290
SEPDMD0300
SEPDMD0310
SEPDMD0320
SEPDMD0330
SEPDMD0340
SEPDMD0350
SEPDMD0360
SEPDMD0370
SEPDMD0380
SEPDMD0390
Order Number
DC
Stock
Order Number
Stock
Unit : mm
CUTTING CONDITIONS
TECHNICAL DATA
N136
Q001
N135
HSS MILLING SHANK DRILLS

HSS
SEPDM
SE High Precision Drill (M)
NEW

Mild Steel ( < 180HB), Aluminium Alloy (Si<5%)
Carbon Steel, Alloy Steel (180 280HB), Gray Cast Iron ( < 350MPa),
Copper, Copper Alloys
AISI 1010 etc
AISI 1045, AISI 4140, No 45 B etc
Work material
Dia.
DC
(mm)
Cutting speed
(m/min)
Revolution
(min-1)
Feed rate
(mm/rev)
Table Feed
(mm/min)
Cutting speed
(m/min)
Revolution
(min-1)
Feed rate
(mm/rev)
Table Feed
(mm/min)
0.5
0.65
24
28
15000
13700
0.02
0.03
300
410
18
22
11250
10700
0.01
0.02
110
210
0.8
33
13100
0.04
520
27
10700
0.03
320
1.0
38
12000
0.05
600
31
10000
0.05
500
1.2
38
10000
0.06
600
31
8200
0.06
490
1.6
2.0
2.5
3.2
4.0
40
40
40
40
40
8000
6400
5100
4000
3200
0.08
0.09
0.11
0.13
0.15
640
575
560
520
480
33
35
35
34
35
6500
5500
4400
3400
2800
0.08
0.09
0.11
0.13
0.15
520
495
480
440
420
Work material
Alloy tool steel ( < 250HB)

Ferritic, Precipitation hardening stainless steel ( < 200HB)
AISI D2, AISI 410, AISI 430 etc
AISI 304LN, AISI 316LN etc
Dia.
DC
(mm)
Cutting speed
(m/min)
Revolution
(min-1)
Feed rate
(mm/rev)
Table Feed
(mm/min)
Cutting speed
(m/min)
Revolution
(min-1)
Feed rate
(mm/rev)
Table Feed
(mm/min)
0.5
0.65
13
14
8000
6800
0.01
0.02
80
135
10
11
6600
5300
0.01
0.012
65
60
0.8
14
5500
0.03
165
11
4300
0.015
60
1.0
1.2
1.6
2.0
2.5
3.2
4.0
16
17
18
18
18
18
18
5000
4500
3500
2900
2300
1800
1400
0.05
0.05
0.06
0.06
0.08
0.09
0.10
250
225
210
170
180
160
140
12
12
14
15
15
15
15
3800
3100
2700
2400
1900
1500
1200
0.02
0.025
0.03
0.04
0.05
0.07
0.09
75
75
80
95
95
105
105
Alloy tool steel ( < 30HRC)

Work material
DRILLING
ASTM H13, AISI L6 etc
N136
Dia.
DC
(mm)
Cutting speed
(m/min)
Revolution
(min-1)
Feed rate
(mm/rev)
Table Feed
(mm/min)
0.5
0.65
0.8
1.0
1.2
1.6
2.0
10
11
11
12
12
14
15
6600
5300
4300
3800
3100
2700
2400
0.01
0.012
0.015
0.02
0.023
0.03
0.04
65
60
60
75
70
80
95
2.5
15
1900
0.04
75
3.2
4.0
15
15
1500
1200
0.05
0.07
75
80
1) Please reduce the revolution and feed rate depending on

the drilling situation when the installation of workpiece or
machine lacks rigidity.
2) Please use a collet type drill chuck or a milling chuck.
3) Use sufficient cutting fluid.
4) VAPDM is recommended when the work material
hardness exceeds 30HRC.
5) WSTAR drill(MWE, MWS) are recommended for
Precipitation hardening stainless steel (JIS-SUS630/ISOL-No58X5CrNiCuNb16-4/ASTM-S17400, JIS-SUS631/
DIN-X7CrNiAl177/ASTM-S17700)
6) When drilling holes greater than 4 x drill diameter hole
depths, please use a peck feed.
7) The above-mentioned cutting condition is standard when
using water-soluble cutting fluid.
Please reduce the revolution when using water-insoluble
cutting fluid.
8) The intermediate diameter revolution is not tabulated.
It is matched to the large diameter side and closest drill
diameter conditions or by calculating the cutting speed of
the closest drill diameter. Set the feedrate per revolution
to a suitable value with the recommended feedrate of the
closest drill diameter as the standard.
VIOLET DRILLS
VAPDS
Short, High precision
P
Steel
HG HSS
118
135
Thinning
DC<2
Stainless Steel Cast Iron
HSS
DC>2
0.5 < DC < 3
3<DC < 6
6<DC < 10
10<DC < 13
0
0.014
0
0.018
0
0.022
0
0.027
drills except those with intervals of 0.1mm

*All
and under dia. 2.0mm have a tolerance of 0 -0.009mm.
PL
DCON(h7)
DC
LF
LCF
a Highly efficient drilling and long tool life have been achieved with the
OAL
DC
LCF OAL LF
PL DCON
VAPDSD0050
VAPDSD0051
VAPDSD0052
VAPDSD0053
VAPDSD0054
VAPDSD0055
VAPDSD0056
VAPDSD0057
VAPDSD0058
VAPDSD0059
VAPDSD0060
VAPDSD0061
VAPDSD0062
VAPDSD0063
VAPDSD0064
VAPDSD0065
VAPDSD0066
VAPDSD0067
VAPDSD0068
VAPDSD0069
VAPDSD0070
VAPDSD0071
VAPDSD0072
VAPDSD0073
VAPDSD0074
VAPDSD0075
VAPDSD0076
VAPDSD0077
VAPDSD0078
VAPDSD0079
VAPDSD0080
VAPDSD0081
VAPDSD0082
VAPDSD0083
VAPDSD0084
VAPDSD0085
VAPDSD0086
VAPDSD0087
VAPDSD0088
VAPDSD0089
0.50
0.51
3.15 50.15
3.15 50.15
50
50
0.15
0.15
3
3
0.52
3.16 50.16
50
0.16
0.53
3.16 50.16
50
0.16
0.54
3.16 50.16
50
0.16
0.55
3.17 50.17
50
0.17
0.56
4.17 50.17
50
0.17
0.57
4.17 50.17
50
0.17
0.58
4.17 50.17
50
0.17
0.59
4.18 50.18
50
0.18
0.60
5.18 50.18
50
0.18
0.61
5.18 50.18
50
0.18
0.62
5.19 50.19
50
0.19
0.63
5.19 50.19
50
0.19
0.64
5.19 50.19
50
0.19
0.65
5.20 50.20
50
0.20
0.66
5.20 50.20
50
0.20
0.67
5.20 50.20
50
0.20
0.68
5.20 50.20
50
0.20
0.69
5.21 50.21
50
0.21
0.70
5.21 50.21
50
0.21
0.71
5.21 50.21
50
0.21
0.72
5.22 50.22
50
0.22
0.73
5.22 50.22
50
0.22
0.74
5.22 50.22
50
0.22
0.75
5.23 50.23
50
0.23
0.76
5.23 50.23
50
0.23
0.77
5.23 50.23
50
0.23
0.78
5.23 50.23
50
0.23
0.79
5.24 50.24
50
0.24
0.80
5.24 50.24
50
0.24
0.81
5.24 50.24
50
0.24
0.82
5.25 50.25
50
0.25
0.83
5.25 50.25
50
0.25
0.84
5.25 50.25
50
0.25
0.85
5.26 50.26
50
0.26
0.86
6.26 50.26
50
0.26
0.87
6.26 50.26
50
0.26
0.88
0.89
6.26 50.26
6.27 50.27
50
50
0.26
0.27
3
3
Order Number
DC
LCF OAL LF
PL DCON
VAPDSD0090
VAPDSD0091
VAPDSD0092
VAPDSD0093
VAPDSD0094
VAPDSD0095
VAPDSD0096
VAPDSD0097
VAPDSD0098
VAPDSD0099
VAPDSD0100
VAPDSD0101
VAPDSD0102
VAPDSD0103
VAPDSD0104
VAPDSD0105
VAPDSD0106
VAPDSD0107
VAPDSD0108
VAPDSD0109
VAPDSD0110
VAPDSD0111
VAPDSD0112
VAPDSD0113
VAPDSD0114
VAPDSD0115
VAPDSD0116
VAPDSD0117
VAPDSD0118
VAPDSD0119
VAPDSD0120
VAPDSD0121
VAPDSD0122
VAPDSD0123
VAPDSD0124
VAPDSD0125
VAPDSD0126
VAPDSD0127
VAPDSD0128
VAPDSD0129
0.90
0.91
6.27 50.27
6.27 50.27
50
50
0.27
0.27
3
3
0.92
6.28 50.28
50
0.28
0.93
6.28 50.28
50
0.28
0.94
6.28 50.28
50
0.28
0.95
6.29 50.29
50
0.29
0.96
6.29 50.29
50
0.29
0.97
6.29 50.29
50
0.29
0.98
6.29 50.29
50
0.29
0.99
6.30 50.30
50
0.30
1.00
6.3 50.3
50
0.3
1.01
6.3 50.3
50
0.3
1.02
6.3 50.3
50
0.3
1.03
6.3 50.3
50
0.3
1.04
6.3 50.3
50
0.3
1.05
6.3 50.3
50
0.3
1.06
6.3 50.3
50
0.3
1.07
8.3 55.3
55
0.3
1.08
8.3 55.3
55
0.3
1.09
8.3 55.3
55
0.3
1.10
8.3 55.3
55
0.3
1.11
8.3 55.3
55
0.3
1.12
8.3 55.3
55
0.3
1.13
8.3 55.3
55
0.3
1.14
8.3 55.3
55
0.3
1.15
8.4 55.4
55
0.4
1.16
8.4 55.4
55
0.4
1.17
8.4 55.4
55
0.4
1.18
8.4 55.4
55
0.4
1.19
8.4 55.4
55
0.4
1.20
8.4 55.4
55
0.4
1.21
8.4 55.4
55
0.4
1.22
8.4 55.4
55
0.4
1.23
8.4 55.4
55
0.4
1.24
8.4 55.4
55
0.4
1.25
8.4 55.4
55
0.4
1.26
8.4 55.4
55
0.4
1.27
8.4 55.4
55
0.4
1.28
1.29
8.4 55.4
8.4 55.4
55
55
0.4
0.4
3
3
DRILLING
Order Number
Unit : mm
Stock
Stock
newly developed Violet coating.

(Standard drill depth : less than 3 times the drill diameter)

CUTTING CONDITIONS
N141
N137
VIOLET DRILLS
HSS
VAPDS
DRILLING
N138
Order Number
DC
VAPDSD0130
VAPDSD0131
VAPDSD0132
VAPDSD0133
VAPDSD0134
VAPDSD0135
VAPDSD0136
VAPDSD0137
VAPDSD0138
VAPDSD0139
VAPDSD0140
VAPDSD0141
VAPDSD0142
VAPDSD0143
VAPDSD0144
VAPDSD0145
VAPDSD0146
VAPDSD0147
VAPDSD0148
VAPDSD0149
VAPDSD0150
VAPDSD0151
VAPDSD0152
VAPDSD0153
VAPDSD0154
VAPDSD0155
VAPDSD0156
VAPDSD0157
VAPDSD0158
VAPDSD0159
VAPDSD0160
VAPDSD0161
VAPDSD0162
VAPDSD0163
VAPDSD0164
VAPDSD0165
VAPDSD0166
VAPDSD0167
VAPDSD0168
VAPDSD0169
VAPDSD0170
VAPDSD0171
VAPDSD0172
VAPDSD0173
VAPDSD0174
VAPDSD0175
VAPDSD0176
VAPDSD0177
VAPDSD0178
VAPDSD0179
1.30
1.31
9.4 55.4
9.4 55.4
55
55
0.4
0.4
3
3
1.32
9.4 55.4
55
0.4
1.33
9.4 55.4
55
0.4
1.34
9.4 55.4
55
0.4
1.35
9.4 55.4
55
0.4
1.36
9.4 55.4
55
0.4
1.37
9.4 55.4
55
0.4
1.38
9.4 55.4
55
0.4
1.39
9.4 55.4
55
0.4
1.40
9.4 55.4
55
0.4
1.41
9.4 55.4
55
0.4
1.42
9.4 55.4
55
0.4
1.43
9.4 55.4
55
0.4
1.44
9.4 55.4
55
0.4
1.45
9.4 55.4
55
0.4
1.46
9.4 55.4
55
0.4
1.47
9.4 55.4
55
0.4
1.48
9.4 55.4
55
0.4
1.49
9.5 55.5
55
0.5
LCF OAL LF
PL DCON
1.50
9.5 55.5
55
0.5
1.51
11.5 55.5
55
0.5
1.52
11.5 55.5
55
0.5
1.53
11.5 55.5
55
0.5
1.54
11.5 55.5
55
0.5
1.55
11.5 55.5
55
0.5
1.56
11.5 55.5
55
0.5
1.57
11.5 55.5
55
0.5
1.58
11.5 55.5
55
0.5
1.59
11.5 55.5
55
0.5
1.60
11.5 55.5
55
0.5
1.61
11.5 55.5
55
0.5
1.62
11.5 55.5
55
0.5
1.63
11.5 55.5
55
0.5
1.64
11.5 55.5
55
0.5
1.65
11.5 55.5
55
0.5
1.66
11.5 55.5
55
0.5
1.67
11.5 55.5
55
0.5
1.68
11.5 55.5
55
0.5
1.69
11.5 55.5
55
0.5
1.70
11.5 55.5
55
0.5
1.71
11.5 55.5
55
0.5
1.72
11.5 55.5
55
0.5
1.73
11.5 55.5
55
0.5
1.74
11.5 55.5
55
0.5
1.75
11.5 55.5
55
0.5
1.76
11.5 55.5
55
0.5
1.77
11.5 55.5
55
0.5
1.78
1.79
11.5 55.5
11.5 55.5
55
55
0.5
0.5
3
3
Stock
Stock
Unit : mm
Order Number
DC
LCF OAL LF
PL DCON
VAPDSD0180
VAPDSD0181
VAPDSD0182
VAPDSD0183
VAPDSD0184
VAPDSD0185
VAPDSD0186
VAPDSD0187
VAPDSD0188
VAPDSD0189
VAPDSD0190
VAPDSD0191
VAPDSD0192
VAPDSD0193
VAPDSD0194
VAPDSD0195
VAPDSD0196
VAPDSD0197
VAPDSD0198
VAPDSD0199
VAPDSD0200
VAPDSD0205
VAPDSD0210
VAPDSD0215
VAPDSD0220
VAPDSD0225
VAPDSD0230
VAPDSD0235
VAPDSD0240
VAPDSD0245
VAPDSD0250
VAPDSD0255
VAPDSD0260
VAPDSD0265
VAPDSD0270
VAPDSD0275
VAPDSD0280
VAPDSD0285
VAPDSD0290
VAPDSD0295
VAPDSD0300
VAPDSD0305
VAPDSD0310
VAPDSD0315
VAPDSD0320
VAPDSD0325
VAPDSD0330
VAPDSD0335
VAPDSD0340
VAPDSD0345
1.80
1.81
11.5 55.5
11.5 55.5
55
55
0.5
0.5
3
3
1.82
11.6 55.6
55
0.6
1.83
11.6 55.6
55
0.6
1.84
11.6 55.6
55
0.6
1.85
11.6 55.6
55
0.6
1.86
11.6 55.6
55
0.6
1.87
11.6 55.6
55
0.6
1.88
11.6 55.6
55
0.6
1.89
11.6 55.6
55
0.6
1.90
12.6 55.6
55
0.6
1.91
12.6 60.6
60
0.6
1.92
12.6 60.6
60
0.6
1.93
12.6 60.6
60
0.6
1.94
12.6 60.6
60
0.6
1.95
12.6 60.6
60
0.6
1.96
12.6 60.6
60
0.6
1.97
12.6 60.6
60
0.6
1.98
12.6 60.6
60
0.6
1.99
12.6 60.6
60
0.6
2.00
12.4 60.4
60
0.4
2.05
12.4 60.4
60
0.4
2.10
12.4 60.4
60
0.4
2.15
12.5 60.5
60
0.5
2.20
12.5 60.5
60
0.5
2.25
12.5 60.5
60
0.5
2.30
13.5 60.5
60
0.5
2.35
13.5 60.5
60
0.5
2.40
13.5 60.5
60
0.5
2.45
13.5 60.5
60
0.5
2.50
13.5 60.5
60
0.5
2.55
13.5 60.5
60
0.5
2.60
15.5 60.5
60
0.5
2.65
15.6 60.6
60
0.6
2.70
15.6 60.6
60
0.6
2.75
15.6 60.6
60
0.6
2.80
15.6 60.6
60
0.6
2.85
15.6 60.6
60
0.6
2.90
15.6 60.6
60
0.6
2.95
15.6 60.6
60
0.6
3.00
15.6 60.6
60
0.6
3.05
17.6 70.6
70
0.6
3.10
17.6 70.6
70
0.6
3.15
17.7 70.7
70
0.7
3.20
17.7 70.7
70
0.7
3.25
17.7 70.7
70
0.7
3.30
19.7 70.7
70
0.7
3.35
19.7 70.7
70
0.7
3.40
3.45
19.7 70.7
19.7 70.7
70
70
0.7
0.7
4
4
HSS
DC
LCF OAL LF
PL DCON
VAPDSD0350
VAPDSD0355
VAPDSD0360
VAPDSD0365
VAPDSD0370
VAPDSD0375
VAPDSD0380
VAPDSD0385
VAPDSD0390
VAPDSD0395
VAPDSD0400
VAPDSD0405
VAPDSD0410
VAPDSD0415
VAPDSD0420
VAPDSD0425
VAPDSD0430
VAPDSD0435
VAPDSD0440
VAPDSD0445
VAPDSD0450
VAPDSD0455
VAPDSD0460
VAPDSD0465
VAPDSD0470
VAPDSD0475
VAPDSD0480
VAPDSD0485
VAPDSD0490
VAPDSD0495
VAPDSD0500
VAPDSD0505
VAPDSD0510
VAPDSD0515
VAPDSD0520
VAPDSD0525
VAPDSD0530
VAPDSD0535
VAPDSD0540
VAPDSD0545
VAPDSD0550
VAPDSD0555
VAPDSD0560
VAPDSD0565
VAPDSD0570
VAPDSD0575
VAPDSD0580
VAPDSD0585
VAPDSD0590
VAPDSD0595
3.50
3.55
19.7 70.7
19.7 70.7
70
70
0.7
0.7
4
4
3.60
21.8 70.8
70
0.8
3.65
21.8 70.8
70
0.8
3.70
21.8 70.8
70
0.8
3.75
21.8 70.8
70
0.8
3.80
21.8 70.8
70
0.8
3.85
21.8 70.8
70
0.8
3.90
21.8 70.8
70
0.8
3.95
21.8 70.8
70
0.8
4.00
21.8 70.8
70
0.8
4.05
21.8 80.8
80
0.8
4.10
21.9 80.9
80
0.9
4.15
21.9 80.9
80
0.9
4.20
21.9 80.9
80
0.9
4.25
21.9 80.9
80
0.9
4.30
23.9 80.9
80
0.9
4.35
23.9 80.9
80
0.9
4.40
23.9 80.9
80
0.9
4.45
23.9 80.9
80
0.9
4.50
23.9 80.9
80
0.9
4.55
23.9 80.9
80
0.9
4.60
26.0 81.0
80
1.0
4.65
26.0 81.0
80
1.0
4.70
26.0 81.0
80
1.0
4.75
26.0 81.0
80
1.0
4.80
26.0 81.0
80
1.0
4.85
26.0 81.0
80
1.0
4.90
26.0 81.0
80
1.0
4.95
26.0 81.0
80
1.0
5.00
26.0 81.0
80
1.0
5.05
26.1 81.1
80
1.1
5.10
26.1 81.1
80
1.1
5.15
26.1 81.1
80
1.1
5.20
26.1 81.1
80
1.1
5.25
26.1 81.1
80
1.1
5.30
26.1 81.1
80
1.1
5.35
28.1 81.1
80
1.1
5.40
28.1 81.1
80
1.1
5.45
28.1 81.1
80
1.1
5.50
28.1 81.1
80
1.1
5.55
28.2 81.2
80
1.2
5.60
28.2 81.2
80
1.2
5.65
28.2 81.2
80
1.2
5.70
28.2 81.2
80
1.2
5.75
28.2 81.2
80
1.2
5.80
28.2 81.2
80
1.2
5.85
28.2 81.2
80
1.2
5.90
5.95
28.2 81.2
28.2 81.2
80
80
1.2
1.2
6
6
Order Number
DC
LCF OAL LF
PL DCON
VAPDSD0600
VAPDSD0605
VAPDSD0610
VAPDSD0615
VAPDSD0620
VAPDSD0625
VAPDSD0630
VAPDSD0635
VAPDSD0640
VAPDSD0645
VAPDSD0650
VAPDSD0655
VAPDSD0660
VAPDSD0665
VAPDSD0670
VAPDSD0675
VAPDSD0680
VAPDSD0685
VAPDSD0690
VAPDSD0695
VAPDSD0700
VAPDSD0705
VAPDSD0710
VAPDSD0715
VAPDSD0720
VAPDSD0725
VAPDSD0730
VAPDSD0735
VAPDSD0740
VAPDSD0745
VAPDSD0750
VAPDSD0755
VAPDSD0760
VAPDSD0765
VAPDSD0770
VAPDSD0775
VAPDSD0780
VAPDSD0785
VAPDSD0790
VAPDSD0795
VAPDSD0800
VAPDSD0805
VAPDSD0810
VAPDSD0815
VAPDSD0820
VAPDSD0825
VAPDSD0830
VAPDSD0835
VAPDSD0840
VAPDSD0845
6.00
6.05
28.2 81.2
31.3 81.3
80
80
1.2
1.3
6
8
6.10
31.3 81.3
80
1.3
6.15
31.3 81.3
80
1.3
6.20
31.3 81.3
80
1.3
6.25
31.3 81.3
80
1.3
6.30
31.3 81.3
80
1.3
6.35
31.3 81.3
80
1.3
6.40
31.3 81.3
80
1.3
6.45
31.3 81.3
80
1.3
6.50
31.4 81.4
80
1.4
6.55
31.4 81.4
80
1.4
6.60
31.4 81.4
80
1.4
6.65
31.4 81.4
80
1.4
6.70
31.4 81.4
80
1.4
6.75
33.4 81.4
80
1.4
6.80
33.4 81.4
80
1.4
6.85
33.4 81.4
80
1.4
6.90
33.4 81.4
80
1.4
6.95
33.4 81.4
80
1.4
7.00
33.5 81.5
80
1.5
7.05
33.5 81.5
80
1.5
7.10
33.5 81.5
80
1.5
7.15
33.5 81.5
80
1.5
7.20
33.5 81.5
80
1.5
7.25
33.5 81.5
80
1.5
7.30
33.5 81.5
80
1.5
7.35
33.5 81.5
80
1.5
7.40
33.5 81.5
80
1.5
7.45
33.5 81.5
80
1.5
7.50
33.6 81.6
80
1.6
7.55
36.6 86.6
85
1.6
7.60
36.6 86.6
85
1.6
7.65
36.6 86.6
85
1.6
7.70
36.6 86.6
85
1.6
7.75
36.6 86.6
85
1.6
7.80
36.6 86.6
85
1.6
7.85
36.6 86.6
85
1.6
7.90
36.6 86.6
85
1.6
7.95
36.7 86.7
85
1.7
8.00
36.7 86.7
85
1.7
8.05
36.7 91.7
90
1.7
10
8.10
36.7 91.7
90
1.7
10
8.15
36.7 91.7
90
1.7
10
8.20
36.7 91.7
90
1.7
10
8.25
36.7 91.7
90
1.7
10
8.30
36.7 91.7
90
1.7
10
8.35
36.7 91.7
90
1.7
10
8.40
8.45
36.7 91.7
36.8 91.8
90
90
1.7
1.8
10
10
CUTTING CONDITIONS
DRILLING
Order Number
Stock
Stock
Unit : mm
N141
N139
VIOLET DRILLS
HSS
VAPDS
DRILLING
N140
Order Number
DC
VAPDSD0850
VAPDSD0855
VAPDSD0860
VAPDSD0865
VAPDSD0870
VAPDSD0875
VAPDSD0880
VAPDSD0885
VAPDSD0890
VAPDSD0895
VAPDSD0900
VAPDSD0905
VAPDSD0910
VAPDSD0915
VAPDSD0920
VAPDSD0925
VAPDSD0930
VAPDSD0935
VAPDSD0940
VAPDSD0945
VAPDSD0950
VAPDSD0955
VAPDSD0960
VAPDSD0965
VAPDSD0970
VAPDSD0975
VAPDSD0980
VAPDSD0985
VAPDSD0990
VAPDSD0995
VAPDSD1000
VAPDSD1005
VAPDSD1010
VAPDSD1015
VAPDSD1020
VAPDSD1025
VAPDSD1030
VAPDSD1035
VAPDSD1040
VAPDSD1045
VAPDSD1050
VAPDSD1055
VAPDSD1060
VAPDSD1065
VAPDSD1070
VAPDSD1075
VAPDSD1080
VAPDSD1085
VAPDSD1090
VAPDSD1095
8.50 36.8
8.55 39.8
91.8
94.8
90
93
1.8
1.8
10
10
8.60 39.8
94.8
93
1.8
10
8.65 39.8
94.8
93
1.8
10
8.70 39.8
94.8
93
1.8
10
8.75 39.8
94.8
93
1.8
10
8.80 39.8
94.8
93
1.8
10
8.85 39.8
94.8
93
1.8
10
8.90 39.8
94.8
93
1.8
10
8.95 39.9
94.9
93
1.9
10
9.00 39.9
94.9
93
1.9
10
9.05 39.9
94.9
93
1.9
10
9.10 39.9
94.9
93
1.9
10
9.15 39.9
94.9
93
1.9
10
9.20 39.9
94.9
93
1.9
10
9.25 39.9
94.9
93
1.9
10
9.30 39.9
94.9
93
1.9
10
9.35 39.9
94.9
93
1.9
10
9.40 40.0
95.0
93
2.0
10
9.45 40.0
95.0
93
2.0
10
9.50 40.0
95.0
93
2.0
10
9.55 43.0
98.0
96
2.0
10
9.60 43.0
98.0
96
2.0
10
9.65 43.0
98.0
96
2.0
10
9.70 43.0
98.0
96
2.0
10
9.75 43.0
98.0
96
2.0
10
9.80 43.0
98.0
96
2.0
10
9.85 43.0
98.0
96
2.0
10
9.90 43.1
98.1
96
2.1
10
9.95 43.1
98.1
96
2.1
10
10.00 43.1
98.1
96
2.1
10
10.05 43.1 103.1 101
2.1
12
10.10 43.1 103.1 101
2.1
12
10.15 43.1 103.1 101
2.1
12
10.20 43.1 103.1 101
2.1
12
10.25 43.1 103.1 101
2.1
12
10.30 43.1 103.1 101
2.1
12
10.35 43.1 103.1 101
2.1
12
10.40 43.2 103.2 101
2.2
12
10.45 43.2 103.2 101
2.2
12
10.50 43.2 103.2 101
2.2
12
10.55 43.2 103.2 101
2.2
12
10.60 43.2 103.2 101
2.2
12
10.65 47.2 107.2 105
2.2
12
10.70 47.2 107.2 105
2.2
12
10.75 47.2 107.2 105
2.2
12
10.80 47.2 107.2 105
2.2
12
10.85 47.3 107.3 105
2.3
12
10.90 47.3 107.3 105

10.95 47.3 107.3 105
2.3
2.3
12
12
LCF OAL LF
PL DCON
Order Number
VAPDSD1100
VAPDSD1105
VAPDSD1110
VAPDSD1115
VAPDSD1120
VAPDSD1125
VAPDSD1130
VAPDSD1135
VAPDSD1140
VAPDSD1145
VAPDSD1150
VAPDSD1155
VAPDSD1160
VAPDSD1165
VAPDSD1170
VAPDSD1175
VAPDSD1180
VAPDSD1185
VAPDSD1190
VAPDSD1195
VAPDSD1200
VAPDSD1210
VAPDSD1220
VAPDSD1230
VAPDSD1240
VAPDSD1250
VAPDSD1260
VAPDSD1270
VAPDSD1280
VAPDSD1290
VAPDSD1300
DC
LCF OAL LF
PL DCON
Stock
Stock
Unit : mm
11.00 47.3 107.3 105

11.05 47.3 107.3 105
2.3
2.3
12
12
11.10 47.3 107.3 105
2.3
12
11.15 47.3 107.3 105
2.3
12
11.20 47.3 107.3 105
2.3
12
11.25 47.3 107.3 105
2.3
12
11.30 47.3 107.3 105
2.3
12
11.35 47.4 107.4 105
2.4
12
11.40 47.4 107.4 105
2.4
12
11.45 47.4 107.4 105
2.4
12
11.50 47.4 107.4 105
2.4
12
11.55 47.4 107.4 105
2.4
12
11.60 47.4 107.4 105
2.4
12
11.65 47.4 107.4 105
2.4
12
11.70 47.4 107.4 105
2.4
12
11.75 47.4 107.4 105
2.4
12
11.80 47.4 107.4 105
2.4
12
11.85 51.5 111.5 109
2.5
12
11.90 51.5 111.5 109
2.5
12
11.95 51.5 111.5 109
2.5
12
12.0
51.5 111.5 109
2.5
12
12.1
51.5 111.5 109
2.5
12
12.2
51.5 111.5 109
2.5
12
12.3
51.6 111.6 109
2.6
12
12.4
51.6 111.6 109
2.6
12
12.5
51.6 111.6 109
2.6
12
12.6
51.6 111.6 109
2.6
12
12.7
51.6 111.6 109
2.6
12
12.8
51.7 111.7 109
2.7
12
12.9
13.0
51.7 111.7 109

51.7 111.7 109
2.7
2.7
12
12
HSS
RECOMMENDED CUTTING CONDITIONS (Standard drilling depth : 3 times or below the drill diameter)
Structural steel
Work
material
Drill Dia.
DC (mm)
Carbon steel AISI 1049

Alloy steel SCM
Cast iron FC
Alloy tool steel AISI D2

(Low-hardness materials)
Ferritic stainless steel
AISI 430, AISI 405
Martensitic stainless steel
AISI 420, AISI 440
Alloy tool steel AISI H13

( 40HRC)
Precipitation
ASTM 630, ASTM 631
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
0.5
1.0
18000
12000
0.02
0.05
16000
10000
0.02
0.05
9000
6300
0.02
0.05
8200
5500
0.02
0.04
2.0
6400
0.09
5500
0.09
3200
0.09
2900
0.05
3.0
4300
0.13
3700
0.13
2100
0.13
1900
0.06
4.0
3200
0.15
2800
0.15
1600
0.15
1400
0.08
5.0
6.0
8.0
10.0
12.0
13.0
2600
2100
1600
1300
1100
980
0.18
0.19
0.24
0.28
0.34
0.36
2200
1800
1400
1100
930
860
0.18
0.19
0.24
0.28
0.34
0.36
1300
1100
800
640
530
490
0.18
0.20
0.22
0.25
0.30
0.32
1100
950
720
570
480
440
0.10
0.11
0.13
0.15
0.17
0.19
1) Please reduce the revolution and feed rate depending on the drilling situation when the installation of workpiece or machine lacks rigidity.
4) VAPDSSUS are recommended for austenitic stainless steels (AISI 304).
5) When drilling holes greater than 4 x drill diameter hole depths, please use a peck feed.
DRILLING
The above-mentioned cutting condition is standard when using water-soluble cutting fluid.
Please reduce the revolution when using non-water-soluble cutting fluid.
N141
VIOLET DRILLS
HSS
VAPDM
Medium, High precision
P
Steel
HG HSS
118
135
Thinning
DC<2
DC>2
0.5 < DC < 3 3<DC < 6 6<DC < 10 10<DC < 18 18<DC < 30 30<DC < 32
0
0.014
0
0.018
0
0.022
PL
0
0.027
0
0.033
0
0.039
DCON(h7)
DC
LF
LCF
OAL
a Highly efficient drilling and long tool life have been achieved
DRILLING
N142
Order Number
DC LCF OAL LF
PL DCON
VAPDMD0050
VAPDMD0055
VAPDMD0060
VAPDMD0065
VAPDMD0070
VAPDMD0075
VAPDMD0080
VAPDMD0085
VAPDMD0090
VAPDMD0095
VAPDMD0100
VAPDMD0105
VAPDMD0110
VAPDMD0115
VAPDMD0120
VAPDMD0125
VAPDMD0130
VAPDMD0135
VAPDMD0140
VAPDMD0145
VAPDMD0150
VAPDMD0155
VAPDMD0160
VAPDMD0165
VAPDMD0170
VAPDMD0175
VAPDMD0180
VAPDMD0185
VAPDMD0190
VAPDMD0195
VAPDMD0200
VAPDMD0205
VAPDMD0210
VAPDMD0215
VAPDMD0220
VAPDMD0225
VAPDMD0230
VAPDMD0235
VAPDMD0240
VAPDMD0245
0.50
0.55
6.15 50.15
6.17 50.17
50
50
0.15
0.17
3
3
0.60
8.18 50.18
50
0.18
0.65
8.20 50.20
50
0.20
0.70 10.21 50.21
50
0.21
0.75 10.23 50.23
50
0.23
0.80 10.24 50.24
50
0.24
0.85 10.26 50.26
50
0.26
0.90 12.27 50.27
50
0.27
0.95 12.29 50.29
50
0.29
1.00 12.3
60.3
60
0.3
1.05 12.3
60.3
60
0.3
1.10 16.3
60.3
60
0.3
1.15 16.4
60.4
60
0.4
1.20 16.4
60.4
60
0.4
1.25 16.4
60.4
60
0.4
1.30 16.4
60.4
60
0.4
1.35 18.4
60.4
60
0.4
1.40 18.4
60.4
60
0.4
1.45 18.4
60.4
60
0.4
1.50 18.5
60.5
60
0.5
1.55 20.5
60.5
60
0.5
1.60 20.5
60.5
60
0.5
1.65 20.5
60.5
60
0.5
1.70 20.5
60.5
60
0.5
1.75 20.5
60.5
60
0.5
1.80 22.5
60.5
60
0.5
1.85 22.6
60.6
60
0.6
1.90 22.6
60.6
60
0.6
1.95 23.6
60.6
60
0.6
2.00 23.4
70.4
70
0.4
2.05 23.4
70.4
70
0.4
2.10 23.4
70.4
70
0.4
2.15 23.5
70.5
70
0.5
2.20 26.5
70.5
70
0.5
2.25 26.5
70.5
70
0.5
2.30 26.5
70.5
70
0.5
2.35 26.5
70.5
70
0.5
2.40 29.5
2.45 29.5
70.5
70.5
70
70
0.5
0.5
3
3
Unit : mm
Stock
Stock
with the newly developed Violet coating.

(Standard drill depth : less than 5 times the drill diameter)
Order Number
DC LCF OAL LF
PL DCON
VAPDMD0250
VAPDMD0255
VAPDMD0260
VAPDMD0265
VAPDMD0270
VAPDMD0275
VAPDMD0280
VAPDMD0285
VAPDMD0290
VAPDMD0295
VAPDMD0300
VAPDMD0305
VAPDMD0310
VAPDMD0315
VAPDMD0320
VAPDMD0325
VAPDMD0330
VAPDMD0335
VAPDMD0340
VAPDMD0345
VAPDMD0350
VAPDMD0355
VAPDMD0360
VAPDMD0365
VAPDMD0370
VAPDMD0375
VAPDMD0380
VAPDMD0385
VAPDMD0390
VAPDMD0395
VAPDMD0400
VAPDMD0405
VAPDMD0410
VAPDMD0415
VAPDMD0420
VAPDMD0425
VAPDMD0430
VAPDMD0435
VAPDMD0440
VAPDMD0445
2.50 29.5
2.55 29.5
70.5
70.5
70
70
0.5
0.5
3
3
2.60 29.5
70.5
70
0.5
2.65 29.6
70.6
70
0.6
2.70 32.6
70.6
70
0.6
2.75 32.6
70.6
70
0.6
2.80 32.6
70.6
70
0.6
2.85 32.6
70.6
70
0.6
2.90 32.6
70.6
70
0.6
2.95 32.6
70.6
70
0.6
3.00 32.6
70.6
70
0.6
3.05 35.6
85.6
85
0.6
3.10 35.6
85.6
85
0.6
3.15 35.7
85.7
85
0.7
3.20 35.7
85.7
85
0.7
3.25 35.7
85.7
85
0.7
3.30 35.7
85.7
85
0.7
3.35 35.7
85.7
85
0.7
3.40 38.7
85.7
85
0.7
3.45 38.7
85.7
85
0.7
3.50 38.7
85.7
85
0.7
3.55 38.7
85.7
85
0.7
3.60 38.8
85.8
85
0.8
3.65 38.8
85.8
85
0.8
3.70 38.8
85.8
85
0.8
3.75 42.8
85.8
85
0.8
3.80 42.8
85.8
85
0.8
3.85 42.8
85.8
85
0.8
3.90 42.8
85.8
85
0.8
3.95 42.8
85.8
85
0.8
4.00 42.8
85.8
85
0.8
4.05 42.8 100.8 100
0.8
4.10 42.9 100.9 100
0.9
4.15 42.9 100.9 100
0.9
4.20 42.9 100.9 100
0.9
4.25 46.9 100.9 100
0.9
4.30 46.9 100.9 100
0.9
4.35 46.9 100.9 100
0.9
4.40 46.9 100.9 100

4.45 46.9 100.9 100
0.9
0.9
6
6
HSS
DC LCF OAL LF
PL DCON
VAPDMD0450
VAPDMD0455
VAPDMD0460
VAPDMD0465
VAPDMD0470
VAPDMD0475
VAPDMD0480
VAPDMD0485
VAPDMD0490
VAPDMD0495
VAPDMD0500
VAPDMD0505
VAPDMD0510
VAPDMD0515
VAPDMD0520
VAPDMD0525
VAPDMD0530
VAPDMD0535
VAPDMD0540
VAPDMD0545
VAPDMD0550
VAPDMD0555
VAPDMD0560
VAPDMD0565
VAPDMD0570
VAPDMD0575
VAPDMD0580
VAPDMD0585
VAPDMD0590
VAPDMD0595
VAPDMD0600
VAPDMD0605
VAPDMD0610
VAPDMD0615
VAPDMD0620
VAPDMD0625
VAPDMD0630
VAPDMD0635
VAPDMD0640
VAPDMD0645
VAPDMD0650
VAPDMD0655
VAPDMD0660
VAPDMD0665
VAPDMD0670
VAPDMD0675
VAPDMD0680
VAPDMD0685
VAPDMD0690
VAPDMD0695
4.50 46.9 100.9 100

4.55 46.9 100.9 100
0.9
0.9
6
6
4.60 47.0 101.0 100
1.0
4.65 47.0 101.0 100
1.0
4.70 47.0 101.0 100
1.0
4.75 47.0 101.0 100
1.0
4.80 52.0 101.0 100
1.0
4.85 52.0 101.0 100
1.0
4.90 52.0 101.0 100
1.0
4.95 52.0 101.0 100
1.0
5.00 52.0 101.0 100
1.0
5.05 52.1 101.1 100
1.1
5.10 52.1 101.1 100
1.1
5.15 52.1 101.1 100
1.1
5.20 52.1 101.1 100
1.1
5.25 52.1 101.1 100
1.1
5.30 52.1 101.1 100
1.1
5.35 57.1 107.1 106
1.1
5.40 57.1 107.1 106
1.1
5.45 57.1 107.1 106
1.1
5.50 57.1 107.1 106
1.1
5.55 57.2 107.2 106
1.2
5.60 57.2 107.2 106
1.2
5.65 57.2 107.2 106
1.2
5.70 57.2 107.2 106
1.2
5.75 57.2 107.2 106
1.2
5.80 57.2 107.2 106
1.2
5.85 57.2 107.2 106
1.2
5.90 57.2 107.2 106
1.2
5.95 57.2 107.2 106
1.2
6.00 57.2 107.2 106
1.2
6.05 63.3 113.3 112
1.3
6.10 63.3 113.3 112
1.3
6.15 63.3 113.3 112
1.3
6.20 63.3 113.3 112
1.3
6.25 63.3 113.3 112
1.3
6.30 63.3 113.3 112
1.3
6.35 63.3 113.3 112
1.3
6.40 63.3 113.3 112
1.3
6.45 63.3 113.3 112
1.3
6.50 63.4 113.4 112
1.4
6.55 63.4 113.4 112
1.4
6.60 63.4 113.4 112
1.4
6.65 63.4 113.4 112
1.4
6.70 63.4 113.4 112
1.4
6.75 68.4 118.4 117
1.4
6.80 68.4 118.4 117
1.4
6.85 68.4 118.4 117
1.4
6.90 68.4 118.4 117

6.95 68.4 118.4 117
1.4
1.4
8
8
Order Number
DC LCF OAL LF
PL DCON
VAPDMD0700
VAPDMD0705
VAPDMD0710
VAPDMD0715
VAPDMD0720
VAPDMD0725
VAPDMD0730
VAPDMD0735
VAPDMD0740
VAPDMD0745
VAPDMD0750
VAPDMD0755
VAPDMD0760
VAPDMD0765
VAPDMD0770
VAPDMD0775
VAPDMD0780
VAPDMD0785
VAPDMD0790
VAPDMD0795
VAPDMD0800
VAPDMD0805
VAPDMD0810
VAPDMD0815
VAPDMD0820
VAPDMD0825
VAPDMD0830
VAPDMD0835
VAPDMD0840
VAPDMD0845
VAPDMD0850
VAPDMD0855
VAPDMD0860
VAPDMD0865
VAPDMD0870
VAPDMD0875
VAPDMD0880
VAPDMD0885
VAPDMD0890
VAPDMD0895
VAPDMD0900
VAPDMD0910
VAPDMD0920
VAPDMD0930
VAPDMD0940
VAPDMD0950
VAPDMD0960
VAPDMD0970
VAPDMD0980
VAPDMD0990
7.00 68.5 118.5 117

7.05 68.5 118.5 117
1.5
1.5
8
8
7.10 68.5 118.5 117
1.5
7.15 68.5 118.5 117
1.5
7.20 68.5 118.5 117
1.5
7.25 68.5 118.5 117
1.5
7.30 68.5 118.5 117
1.5
7.35 68.5 118.5 117
1.5
7.40 68.5 118.5 117
1.5
7.45 68.5 118.5 117
1.5
7.50 68.6 118.6 117
1.6
7.55 74.6 124.6 123
1.6
7.60 74.6 124.6 123
1.6
7.65 74.6 124.6 123
1.6
7.70 74.6 124.6 123
1.6
7.75 74.6 124.6 123
1.6
7.80 74.6 124.6 123
1.6
7.85 74.6 124.6 123
1.6
7.90 74.6 124.6 123
1.6
7.95 74.7 124.7 123
1.7
8.00 74.7 124.7 123
1.7
8.05 74.7 129.7 128
1.7
10
8.10 74.7 129.7 128
1.7
10
8.15 74.7 129.7 128
1.7
10
8.20 74.7 129.7 128
1.7
10
8.25 74.7 129.7 128
1.7
10
8.30 74.7 129.7 128
1.7
10
8.35 74.7 129.7 128
1.7
10
8.40 74.7 129.7 128
1.7
10
8.45 74.8 129.8 128
1.8
10
8.50 74.8 129.8 128
1.8
10
8.55 80.8 135.8 134
1.8
10
8.60 80.8 135.8 134
1.8
10
8.65 80.8 135.8 134
1.8
10
8.70 80.8 135.8 134
1.8
10
8.75 80.8 135.8 134
1.8
10
8.80 80.8 135.8 134
1.8
10
8.85 80.8 135.8 134
1.8
10
8.90 80.8 135.8 134
1.8
10
8.95 80.9 135.9 134
1.9
10
9.00 80.9 135.9 134
1.9
10
9.10 80.9 135.9 134
1.9
10
9.20 80.9 135.9 134
1.9
10
9.30 80.9 135.9 134
1.9
10
9.40 81.0 136.0 134
2.0
10
9.50 81.0 136.0 134
2.0
10
9.60 87.0 142.0 140
2.0
10
9.70 87.0 142.0 140
2.0
10
9.80 87.0 142.0 140

9.90 87.1 142.1 140
2.0
2.1
10
10
CUTTING CONDITIONS
DRILLING
Order Number
Stock
Stock
Unit : mm
N145
N143
VIOLET DRILLS
HSS
VAPDM
Medium, High precision
DRILLING
N144
Order Number
DC LCF OAL LF
PL DCON
VAPDMD1000
VAPDMD1010
VAPDMD1020
VAPDMD1030
VAPDMD1040
VAPDMD1050
VAPDMD1060
VAPDMD1070
VAPDMD1080
VAPDMD1090
VAPDMD1100
VAPDMD1110
VAPDMD1120
VAPDMD1130
VAPDMD1140
VAPDMD1150
VAPDMD1160
VAPDMD1170
VAPDMD1180
VAPDMD1190
VAPDMD1200
VAPDMD1210
VAPDMD1220
VAPDMD1230
VAPDMD1240
VAPDMD1250
VAPDMD1260
VAPDMD1270
VAPDMD1280
VAPDMD1290
VAPDMD1300
VAPDMD1350
VAPDMD1400
VAPDMD1410
VAPDMD1420
VAPDMD1450
VAPDMD1500
VAPDMD1550
VAPDMD1560
VAPDMD1570
VAPDMD1600
VAPDMD1650
VAPDMD1700
VAPDMD1750
VAPDMD1760
VAPDMD1770
VAPDMD1800
VAPDMD1850
VAPDMD1900
VAPDMD1950
10.0
10.1
87.1 142.1 140

87.1 147.1 145
2.1
2.1
10
12
10.2
87.1 147.1 145
2.1
12
10.3
87.1 147.1 145
2.1
12
10.4
87.2 147.2 145
2.2
12
10.5
87.2 147.2 145
2.2
12
10.6
87.2 147.2 145
2.2
12
10.7
94.2 154.2 152
2.2
12
10.8
94.2 154.2 152
2.2
12
10.9
94.3 154.3 152
2.3
12
11.0
94.3 154.3 152
2.3
12
11.1
94.3 154.3 152
2.3
12
11.2
94.3 154.3 152
2.3
12
11.3
94.3 154.3 152
2.3
12
11.4
94.4 154.4 152
2.4
12
11.5
94.4 154.4 152
2.4
12
11.6
94.4 154.4 152
2.4
12
11.7
94.4 154.4 152
2.4
12
11.8
94.4 154.4 152
2.4
12
11.9 101.5 161.5 159
2.5
12
12.0 101.5 161.5 159
2.5
12
12.1 101.5 161.5 159
2.5
12
12.2 101.5 161.5 159
2.5
12
12.3 101.6 161.6 159
2.6
12
12.4 101.6 161.6 159
2.6
12
12.5 101.6 161.6 159
2.6
12
12.6 101.6 161.6 159
2.6
12
12.7 101.6 161.6 159
2.6
12
12.8 101.7 161.7 159
2.7
12
12.9 101.7 161.7 159
2.7
12
13.0 101.7 161.7 159
2.7
12
13.5 102.8 162.8 160
2.8
16
14.0 102.9 162.9 160
2.9
16
14.1 107.9 167.9 165
2.9
16
14.2 107.9 167.9 165
2.9
16
14.5 108.0 168.0 165
3.0
16
15.0 108.1 168.1 165
3.1
16
15.5 113.2 173.2 170
3.2
16
15.6 113.2 173.2 170
3.2
16
15.7 113.3 173.3 170
3.3
16
16.0 113.3 173.3 170
3.3
16
16.5 113.4 178.4 175
3.4
20
17.0 113.5 178.5 175
3.5
20
17.5 118.6 183.6 180
3.6
20
17.6 118.7 183.7 180
3.7
20
17.7 118.7 183.7 180
3.7
20
18.0 118.7 183.7 180
3.7
20
18.5 123.8 188.8 185
3.8
20
19.0 123.9 188.9 185

19.5 124.0 189.0 185
3.9
4.0
20
20
Stock
Stock
Unit : mm
Order Number
DC LCF OAL LF
PL DCON
VAPDMD1960
VAPDMD1970
VAPDMD2000
VAPDMD2050
VAPDMD2100
VAPDMD2110
VAPDMD2120
VAPDMD2150
VAPDMD2200
VAPDMD2250
VAPDMD2300
VAPDMD2350
VAPDMD2400
VAPDMD2450
VAPDMD2500
VAPDMD2550
VAPDMD2600
VAPDMD2650
VAPDMD2700
VAPDMD2800
VAPDMD2900
VAPDMD3000
VAPDMD3100
VAPDMD3200
19.6 124.1 189.1 185

19.7 124.1 189.1 185
4.1
4.1
20
20
20.0 124.1 189.1 185
4.1
20
20.5 129.3 204.3 200
4.3
25
21.0 129.4 204.4 200
4.4
25
21.1 129.4 204.4 200
4.4
25
21.2 129.4 204.4 200
4.4
25
21.5 129.5 204.5 200
4.5
25
22.0 129.6 204.6 200
4.6
25
22.5 134.7 209.7 205
4.7
25
23.0 134.8 209.8 205
4.8
25
23.5 134.9 209.9 205
4.9
25
24.0 140.0 215.0 210
5.0
25
24.5 140.1 215.1 210
5.1
25
25.0 140.2 215.2 210
5.2
25
25.5 145.3 225.3 220
5.3
32
26.0 145.4 225.4 220
5.4
32
26.5 145.5 225.5 220
5.5
32
27.0 145.6 225.6 220
5.6
32
28.0 145.8 225.8 220
5.8
32
29.0 151.0 231.0 225
6.0
32
30.0 151.2 231.2 225
6.2
32
31.0 156.4 236.4 230

32.0 161.6 241.6 235
6.4
6.6
32
32
HSS
RECOMMENDED CUTTING CONDITIONS (Standard drilling depth : 5 times or below the drill diameter)
Structural steel
Work
material

Alloy steel SCM
Cast iron FC

AISI 430, AISI 405
AISI 420, AISI 440

( 40HRC)
Precipitation
ASTM 630, ASTM 631
Drill Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
0.5
1.0
17000
11000
0.01
0.05
12800
8300
0.01
0.05
8000
5000
0.01
0.05
6600
4100
0.01
0.04
2.0
6400
0.09
4800
0.09
2900
0.06
2400
0.05
3.0
4300
0.13
3200
0.13
1900
0.10
1600
0.06
4.0
3200
0.15
2400
0.15
1400
0.10
1200
0.08
5.0
6.0
8.0
10.0
12.0
14.0
2600
2100
1600
1300
1100
910
0.18
0.19
0.24
0.28
0.34
0.39
1900
1600
1200
950
800
680
0.18
0.20
0.22
0.25
0.30
0.35
1100
950
720
570
480
410
0.13
0.15
0.18
0.21
0.25
0.30
950
800
600
480
400
340
0.10
0.11
0.13
0.15
0.17
0.21
15.0
16.0
850
800
0.40
0.42
640
600
0.36
0.38
380
360
0.31
0.32
320
300
0.22
0.23
18.0
710
0.44
530
0.40
320
0.34
270
0.24
20.0
570
0.44
450
0.40
250
0.34
220
0.24
22.0
520
0.46
410
0.42
230
0.36
200
0.25
24.0
480
0.48
370
0.44
210
0.37
190
0.26
26.0
28.0
30.0
32.0
440
410
380
360
0.51
0.53
0.55
0.55
340
320
300
280
0.46
0.48
0.50
0.50
200
180
170
160
0.39
0.41
0.43
0.43
170
160
150
140
0.28
0.29
0.30
0.30
4) VAPDMSUS are recommended for austenitic stainless steels (AISI 304).
DRILLING
N145
VIOLET DRILLS
HSS
VAPDSSUS
Short, High precision, For stainless steel
P
Steel
CO HSS
135
Thinning
DC>1
0.5 < DC < 3 3<DC < 6 6<DC < 10 10<DC < 1818<DC < 20
0
0.014
0
0.018
0
0.022
0
0.027
0
0.033

*All
and under dia. 4.0mm have a tolerance of 0-0.009mm.
PL
DCON(h7)
DC
LF
LCF
OAL
a New design and the Violet coating combination enable high
efficiency drilling and long tool life for drilling of stainless steels.
DRILLING
VAPDSSUSD0050
VAPDSSUSD0051
VAPDSSUSD0052
VAPDSSUSD0053
VAPDSSUSD0054
VAPDSSUSD0055
VAPDSSUSD0056
VAPDSSUSD0057
VAPDSSUSD0058
VAPDSSUSD0059
VAPDSSUSD0060
VAPDSSUSD0061
VAPDSSUSD0062
VAPDSSUSD0063
VAPDSSUSD0064
VAPDSSUSD0065
VAPDSSUSD0066
VAPDSSUSD0067
VAPDSSUSD0068
VAPDSSUSD0069
VAPDSSUSD0070
VAPDSSUSD0071
VAPDSSUSD0072
VAPDSSUSD0073
VAPDSSUSD0074
VAPDSSUSD0075
VAPDSSUSD0076
VAPDSSUSD0077
VAPDSSUSD0078
VAPDSSUSD0079
VAPDSSUSD0080
VAPDSSUSD0081
VAPDSSUSD0082
VAPDSSUSD0083
VAPDSSUSD0084
VAPDSSUSD0085
VAPDSSUSD0086
VAPDSSUSD0087
VAPDSSUSD0088
VAPDSSUSD0089
N146
DC LCF OAL LF
PL DCON
0.50 3.10 50.10

0.51 3.11 50.11
50
50
0.10
0.11
3
3
0.52
3.11 50.11
50
0.11
0.53
3.11 50.11
50
0.11
0.54
3.11 50.11
50
0.11
0.55
3.11 50.11
50
0.11
0.56 4.12 50.12
50
0.12
0.57 4.12 50.12
50
0.12
0.58 4.12 50.12
50
0.12
0.59 4.12 50.12
50
0.12
0.60 5.12 50.12
50
0.12
0.61 5.13 50.13
50
0.13
0.62 5.13 50.13
50
0.13
0.63 5.13 50.13
50
0.13
0.64 5.13 50.13
50
0.13
0.65 5.13 50.13
50
0.13
0.66 5.14 50.14
50
0.14
0.67 5.14 50.14
50
0.14
0.68 5.14 50.14
50
0.14
0.69 5.14 50.14
50
0.14
0.70 5.14 50.14
50
0.14
0.71 5.15 50.15
50
0.15
0.72 5.15 50.15
50
0.15
0.73 5.15 50.15
50
0.15
0.74 5.15 50.15
50
0.15
0.75 5.16 50.16
50
0.16
0.76 5.16 50.16
50
0.16
0.77 5.16 50.16
50
0.16
0.78 5.16 50.16
50
0.16
0.79 5.16 50.16
50
0.16
0.80 5.17 50.17
50
0.17
0.81 5.17 50.17
50
0.17
0.82 5.17 50.17
50
0.17
0.83 5.17 50.17
50
0.17
0.84 5.17 50.17
50
0.17
0.85 5.18 50.18
50
0.18
0.86 6.18 50.18
50
0.18
0.87 6.18 50.18
50
0.18
0.88 6.18 50.18

0.89 6.18 50.18
50
50
0.18
0.18
3
3
Order Number
VAPDSSUSD0090
VAPDSSUSD0091
VAPDSSUSD0092
VAPDSSUSD0093
VAPDSSUSD0094
VAPDSSUSD0095
VAPDSSUSD0096
VAPDSSUSD0097
VAPDSSUSD0098
VAPDSSUSD0099
VAPDSSUSD0100
VAPDSSUSD0101
VAPDSSUSD0102
VAPDSSUSD0103
VAPDSSUSD0104
VAPDSSUSD0105
VAPDSSUSD0106
VAPDSSUSD0107
VAPDSSUSD0108
VAPDSSUSD0109
VAPDSSUSD0110
VAPDSSUSD0111
VAPDSSUSD0112
VAPDSSUSD0113
VAPDSSUSD0114
VAPDSSUSD0115
VAPDSSUSD0116
VAPDSSUSD0117
VAPDSSUSD0118
VAPDSSUSD0119
VAPDSSUSD0120
VAPDSSUSD0121
VAPDSSUSD0122
VAPDSSUSD0123
VAPDSSUSD0124
VAPDSSUSD0125
VAPDSSUSD0126
VAPDSSUSD0127
VAPDSSUSD0128
VAPDSSUSD0129
Stock
Order Number
Stock
Unit : mm
DC LCF OAL LF
PL DCON
0.90 6.19 50.19

0.91 6.19 50.19
50
50
0.19
0.19
3
3
0.92 6.19 50.19
50
0.19
0.93 6.19 50.19
50
0.19
0.94 6.19 50.19
50
0.19
0.95 6.20 50.20
50
0.20
0.96 6.20 50.20
50
0.20
0.97 6.20 50.20
50
0.20
0.98 6.20 50.20
50
0.20
0.99 6.21 50.21
50
0.21
1.00
6.2 50.2
50
0.2
1.01
6.2 50.2
50
0.2
1.02
6.2 50.2
50
0.2
1.03
6.2 50.2
50
0.2
1.04
6.2 50.2
50
0.2
1.05
6.2 50.2
50
0.2
1.06
6.2 50.2
50
0.2
1.07
8.2 55.2
55
0.2
1.08
8.2 55.2
55
0.2
1.09
8.2 55.2
55
0.2
1.10
8.2 55.2
55
0.2
1.11
8.2 55.2
55
0.2
1.12
8.2 55.2
55
0.2
1.13
8.2 55.2
55
0.2
1.14
8.2 55.2
55
0.2
1.15
8.2 55.2
55
0.2
1.16
8.2 55.2
55
0.2
1.17
8.2 55.2
55
0.2
1.18
8.2 55.2
55
0.2
1.19
8.3 55.3
55
0.3
1.20
8.3 55.3
55
0.3
1.21
8.3 55.3
55
0.3
1.22
8.3 55.3
55
0.3
1.23
8.3 55.3
55
0.3
1.24
8.3 55.3
55
0.3
1.25
8.3 55.3
55
0.3
1.26
8.3 55.3
55
0.3
1.27
8.3 55.3
55
0.3
1.28
1.29
8.3 55.3
8.3 55.3
55
55
0.3
0.3
3
3
HSS
PL DCON
1.30
1.31
9.3 55.3
9.3 55.3
55
55
0.3
0.3
3
3
1.32
9.3 55.3
55
0.3
1.33
9.3 55.3
55
0.3
1.34
9.3 55.3
55
0.3
1.35
9.3 55.3
55
0.3
1.36
9.3 55.3
55
0.3
1.37
9.3 55.3
55
0.3
1.38
9.3 55.3
55
0.3
1.39
9.3 55.3
55
0.3
1.40
9.3 55.3
55
0.3
1.41
9.3 55.3
55
0.3
1.42
9.3 55.3
55
0.3
1.43
9.3 55.3
55
0.3
1.44
9.3 55.3
55
0.3
1.45
9.3 55.3
55
0.3
1.46
9.3 55.3
55
0.3
1.47
9.3 55.3
55
0.3
1.48
9.3 55.3
55
0.3
1.49
9.3 55.3
55
0.3
1.50
9.3 55.3
55
0.3
1.51 11.3 55.3
55
0.3
1.52 11.3 55.3
55
0.3
1.53 11.3 55.3
55
0.3
1.54 11.3 55.3
55
0.3
1.55 11.3 55.3
55
0.3
1.56 11.3 55.3
55
0.3
1.57 11.3 55.3
55
0.3
1.58 11.3 55.3
55
0.3
1.59 11.3 55.3
55
0.3
1.60 11.3 55.3
55
0.3
1.61 11.3 55.3
55
0.3
1.62 11.3 55.3
55
0.3
1.63 11.3 55.3
55
0.3
1.64 11.3 55.3
55
0.3
1.65 11.3 55.3
55
0.3
1.66 11.3 55.3
55
0.3
1.67 11.4 55.4
55
0.4
1.68 11.4 55.4
55
0.4
1.69 11.4 55.4
55
0.4
1.70 11.4 55.4
55
0.4
1.71 11.4 55.4
55
0.4
1.72 11.4 55.4
55
0.4
1.73 11.4 55.4
55
0.4
1.74 11.4 55.4
55
0.4
1.75 11.4 55.4
55
0.4
1.76 11.4 55.4
55
0.4
1.77 11.4 55.4
55
0.4
1.78 11.4 55.4

1.79 11.4 55.4
55
55
0.4
0.4
3
3
a
a
Order Number
VAPDSSUSD0180
VAPDSSUSD0181
VAPDSSUSD0182
VAPDSSUSD0183
VAPDSSUSD0184
VAPDSSUSD0185
VAPDSSUSD0186
VAPDSSUSD0187
VAPDSSUSD0188
VAPDSSUSD0189
VAPDSSUSD0190
VAPDSSUSD0191
VAPDSSUSD0192
VAPDSSUSD0193
VAPDSSUSD0194
VAPDSSUSD0195
VAPDSSUSD0196
VAPDSSUSD0197
VAPDSSUSD0198
VAPDSSUSD0199
VAPDSSUSD0200
VAPDSSUSD0201
VAPDSSUSD0202
VAPDSSUSD0203
VAPDSSUSD0204
VAPDSSUSD0205
VAPDSSUSD0206
VAPDSSUSD0207
VAPDSSUSD0208
VAPDSSUSD0209
VAPDSSUSD0210
VAPDSSUSD0211
VAPDSSUSD0212
VAPDSSUSD0213
VAPDSSUSD0214
VAPDSSUSD0215
VAPDSSUSD0216
VAPDSSUSD0217
VAPDSSUSD0218
VAPDSSUSD0219
VAPDSSUSD0220
VAPDSSUSD0221
VAPDSSUSD0222
VAPDSSUSD0223
VAPDSSUSD0224
VAPDSSUSD0225
VAPDSSUSD0226
VAPDSSUSD0227
VAPDSSUSD0228
VAPDSSUSD0229
DC LCF OAL LF
PL DCON
1.80 11.4 55.4

1.81 11.4 55.4
55
55
0.4
0.4
3
3
1.82 11.4 55.4
55
0.4
1.83 11.4 55.4
55
0.4
1.84 11.4 55.4
55
0.4
1.85 11.4 55.4
55
0.4
1.86 11.4 55.4
55
0.4
1.87 11.4 55.4
55
0.4
1.88 11.4 55.4
55
0.4
1.89 11.4 55.4
55
0.4
1.90 12.4 55.4
55
0.4
1.91 12.4 60.4
60
0.4
1.92 12.4 60.4
60
0.4
1.93 12.4 60.4
60
0.4
1.94 12.4 60.4
60
0.4
1.95 12.4 60.4
60
0.4
1.96 12.4 60.4
60
0.4
1.97 12.4 60.4
60
0.4
1.98 12.4 60.4
60
0.4
1.99 12.4 60.4
60
0.4
2.00 12.4 60.4
60
0.4
2.01 12.4 60.4
60
0.4
2.02 12.4 60.4
60
0.4
2.03 12.4 60.4
60
0.4
2.04 12.4 60.4
60
0.4
2.05 12.4 60.4
60
0.4
2.06 12.4 60.4
60
0.4
2.07 12.4 60.4
60
0.4
2.08 12.4 60.4
60
0.4
2.09 12.4 60.4
60
0.4
2.10 12.4 60.4
60
0.4
2.11 12.4 60.4
60
0.4
2.12 12.4 60.4
60
0.4
2.13 12.4 60.4
60
0.4
2.14 12.4 60.4
60
0.4
2.15 12.5 60.5
60
0.5
2.16 12.5 60.5
60
0.5
2.17 12.5 60.5
60
0.5
2.18 12.5 60.5
60
0.5
2.19 12.5 60.5
60
0.5
2.20 12.5 60.5
60
0.5
2.21 12.5 60.5
60
0.5
2.22 12.5 60.5
60
0.5
2.23 12.5 60.5
60
0.5
2.24 12.5 60.5
60
0.5
2.25 12.5 60.5
60
0.5
2.26 12.5 60.5
60
0.5
2.27 12.5 60.5
60
0.5
2.28 12.5 60.5

2.29 12.5 60.5
60
60
0.5
0.5
3
3
CUTTING CONDITIONS
DRILLING
VAPDSSUSD0130
VAPDSSUSD0131
VAPDSSUSD0132
VAPDSSUSD0133
VAPDSSUSD0134
VAPDSSUSD0135
VAPDSSUSD0136
VAPDSSUSD0137
VAPDSSUSD0138
VAPDSSUSD0139
VAPDSSUSD0140
VAPDSSUSD0141
VAPDSSUSD0142
VAPDSSUSD0143
VAPDSSUSD0144
VAPDSSUSD0145
VAPDSSUSD0146
VAPDSSUSD0147
VAPDSSUSD0148
VAPDSSUSD0149
VAPDSSUSD0150
VAPDSSUSD0151
VAPDSSUSD0152
VAPDSSUSD0153
VAPDSSUSD0154
VAPDSSUSD0155
VAPDSSUSD0156
VAPDSSUSD0157
VAPDSSUSD0158
VAPDSSUSD0159
VAPDSSUSD0160
VAPDSSUSD0161
VAPDSSUSD0162
VAPDSSUSD0163
VAPDSSUSD0164
VAPDSSUSD0165
VAPDSSUSD0166
VAPDSSUSD0167
VAPDSSUSD0168
VAPDSSUSD0169
VAPDSSUSD0170
VAPDSSUSD0171
VAPDSSUSD0172
VAPDSSUSD0173
VAPDSSUSD0174
VAPDSSUSD0175
VAPDSSUSD0176
VAPDSSUSD0177
VAPDSSUSD0178
VAPDSSUSD0179
DC LCF OAL LF
Stock
Order Number
Stock
Unit : mm
N158
N147
VIOLET DRILLS
HSS
VAPDSSUS
DRILLING
VAPDSSUSD0230
VAPDSSUSD0231
VAPDSSUSD0232
VAPDSSUSD0233
VAPDSSUSD0234
VAPDSSUSD0235
VAPDSSUSD0236
VAPDSSUSD0237
VAPDSSUSD0238
VAPDSSUSD0239
VAPDSSUSD0240
VAPDSSUSD0241
VAPDSSUSD0242
VAPDSSUSD0243
VAPDSSUSD0244
VAPDSSUSD0245
VAPDSSUSD0246
VAPDSSUSD0247
VAPDSSUSD0248
VAPDSSUSD0249
VAPDSSUSD0250
VAPDSSUSD0251
VAPDSSUSD0252
VAPDSSUSD0253
VAPDSSUSD0254
VAPDSSUSD0255
VAPDSSUSD0256
VAPDSSUSD0257
VAPDSSUSD0258
VAPDSSUSD0259
VAPDSSUSD0260
VAPDSSUSD0261
VAPDSSUSD0262
VAPDSSUSD0263
VAPDSSUSD0264
VAPDSSUSD0265
VAPDSSUSD0266
VAPDSSUSD0267
VAPDSSUSD0268
VAPDSSUSD0269
VAPDSSUSD0270
VAPDSSUSD0271
VAPDSSUSD0272
VAPDSSUSD0273
VAPDSSUSD0274
VAPDSSUSD0275
VAPDSSUSD0276
VAPDSSUSD0277
VAPDSSUSD0278
VAPDSSUSD0279
N148
DC LCF OAL LF
PL DCON
2.30 13.5 60.5

2.31 13.5 60.5
60
60
0.5
0.5
3
3
2.32 13.5 60.5
60
0.5
2.33 13.5 60.5
60
0.5
2.34 13.5 60.5
60
0.5
2.35 13.5 60.5
60
0.5
2.36 13.5 60.5
60
0.5
2.37 13.5 60.5
60
0.5
2.38 13.5 60.5
60
0.5
2.39 13.5 60.5
60
0.5
2.40 13.5 60.5
60
0.5
2.41 13.5 60.5
60
0.5
2.42 13.5 60.5
60
0.5
2.43 13.5 60.5
60
0.5
2.44 13.5 60.5
60
0.5
2.45 13.5 60.5
60
0.5
2.46 13.5 60.5
60
0.5
2.47 13.5 60.5
60
0.5
2.48 13.5 60.5
60
0.5
2.49 13.5 60.5
60
0.5
2.50 13.5 60.5
60
0.5
2.51 13.5 60.5
60
0.5
2.52 13.5 60.5
60
0.5
2.53 13.5 60.5
60
0.5
2.54 13.5 60.5
60
0.5
2.55 13.5 60.5
60
0.5
2.56 13.5 60.5
60
0.5
2.57 13.5 60.5
60
0.5
2.58 13.5 60.5
60
0.5
2.59 13.5 60.5
60
0.5
2.60 15.5 60.5
60
0.5
2.61 15.5 60.5
60
0.5
2.62 15.5 60.5
60
0.5
2.63 15.5 60.5
60
0.5
2.64 15.6 60.6
60
0.6
2.65 15.6 60.6
60
0.6
2.66 15.6 60.6
60
0.6
2.67 15.6 60.6
60
0.6
2.68 15.6 60.6
60
0.6
2.69 15.6 60.6
60
0.6
2.70 15.6 60.6
60
0.6
2.71 15.6 60.6
60
0.6
2.72 15.6 60.6
60
0.6
2.73 15.6 60.6
60
0.6
2.74 15.6 60.6
60
0.6
2.75 15.6 60.6
60
0.6
2.76 15.6 60.6
60
0.6
2.77 15.6 60.6
60
0.6
2.78 15.6 60.6

2.79 15.6 60.6
60
60
0.6
0.6
3
3
Order Number
VAPDSSUSD0280
VAPDSSUSD0281
VAPDSSUSD0282
VAPDSSUSD0283
VAPDSSUSD0284
VAPDSSUSD0285
VAPDSSUSD0286
VAPDSSUSD0287
VAPDSSUSD0288
VAPDSSUSD0289
VAPDSSUSD0290
VAPDSSUSD0291
VAPDSSUSD0292
VAPDSSUSD0293
VAPDSSUSD0294
VAPDSSUSD0295
VAPDSSUSD0296
VAPDSSUSD0297
VAPDSSUSD0298
VAPDSSUSD0299
VAPDSSUSD0300
VAPDSSUSD0301
VAPDSSUSD0302
VAPDSSUSD0303
VAPDSSUSD0304
VAPDSSUSD0305
VAPDSSUSD0306
VAPDSSUSD0307
VAPDSSUSD0308
VAPDSSUSD0309
VAPDSSUSD0310
VAPDSSUSD0311
VAPDSSUSD0312
VAPDSSUSD0313
VAPDSSUSD0314
VAPDSSUSD0315
VAPDSSUSD0316
VAPDSSUSD0317
VAPDSSUSD0318
VAPDSSUSD0319
VAPDSSUSD0320
VAPDSSUSD0321
VAPDSSUSD0322
VAPDSSUSD0323
VAPDSSUSD0324
VAPDSSUSD0325
VAPDSSUSD0326
VAPDSSUSD0327
VAPDSSUSD0328
VAPDSSUSD0329
Stock
Order Number
Stock
Unit : mm
DC LCF OAL LF
PL DCON
2.80 15.6 60.6

2.81 15.6 60.6
60
60
0.6
0.6
3
3
2.82 15.6 60.6
60
0.6
2.83 15.6 60.6
60
0.6
2.84 15.6 60.6
60
0.6
2.85 15.6 60.6
60
0.6
2.86 15.6 60.6
60
0.6
2.87 15.6 60.6
60
0.6
2.88 15.6 60.6
60
0.6
2.89 15.6 60.6
60
0.6
2.90 15.6 60.6
60
0.6
2.91 15.6 60.6
60
0.6
2.92 15.6 60.6
60
0.6
2.93 15.6 60.6
60
0.6
2.94 15.6 60.6
60
0.6
2.95 15.6 60.6
60
0.6
2.96 15.6 60.6
60
0.6
2.97 15.6 60.6
60
0.6
2.98 15.6 60.6
60
0.6
2.99 15.6 60.6
60
0.6
3.00 15.6 60.6
60
0.6
3.01 17.6 70.6
70
0.6
3.02 17.6 70.6
70
0.6
3.03 17.6 70.6
70
0.6
3.04 17.6 70.6
70
0.6
3.05 17.6 70.6
70
0.6
3.06 17.6 70.6
70
0.6
3.07 17.6 70.6
70
0.6
3.08 17.6 70.6
70
0.6
3.09 17.6 70.6
70
0.6
3.10 17.6 70.6
70
0.6
3.11 17.6 70.6
70
0.6
3.12 17.7 70.7
70
0.7
3.13 17.7 70.7
70
0.7
3.14 17.7 70.7
70
0.7
3.15 17.7 70.7
70
0.7
3.16 17.7 70.7
70
0.7
3.17 17.7 70.7
70
0.7
3.18 17.7 70.7
70
0.7
3.19 17.7 70.7
70
0.7
3.20 17.7 70.7
70
0.7
3.21 17.7 70.7
70
0.7
3.22 17.7 70.7
70
0.7
3.23 17.7 70.7
70
0.7
3.24 17.7 70.7
70
0.7
3.25 17.7 70.7
70
0.7
3.26 17.7 70.7
70
0.7
3.27 17.7 70.7
70
0.7
3.28 17.7 70.7

3.29 17.7 70.7
70
70
0.7
0.7
4
4
a
a
HSS
PL DCON
3.30 19.7 70.7

3.31 19.7 70.7
70
70
0.7
0.7
4
4
3.32 19.7 70.7
70
0.7
3.33 19.7 70.7
70
0.7
3.34 19.7 70.7
70
0.7
3.35 19.7 70.7
70
0.7
3.36 19.7 70.7
70
0.7
3.37 19.7 70.7
70
0.7
3.38 19.7 70.7
70
0.7
3.39 19.7 70.7
70
0.7
3.40 19.7 70.7
70
0.7
3.41 19.7 70.7
70
0.7
3.42 19.7 70.7
70
0.7
3.43 19.7 70.7
70
0.7
3.44 19.7 70.7
70
0.7
3.45 19.7 70.7
70
0.7
3.46 19.7 70.7
70
0.7
3.47 19.7 70.7
70
0.7
3.48 19.7 70.7
70
0.7
3.49 19.7 70.7
70
0.7
3.50 19.7 70.7
70
0.7
3.51 19.7 70.7
70
0.7
3.52 19.7 70.7
70
0.7
3.53 19.7 70.7
70
0.7
3.54 19.7 70.7
70
0.7
3.55 19.7 70.7
70
0.7
3.56 19.7 70.7
70
0.7
3.57 19.7 70.7
70
0.7
3.58 19.7 70.7
70
0.7
3.59 19.7 70.7
70
0.7
3.60 21.8 70.8
70
0.8
3.61 21.8 70.8
70
0.8
3.62 21.8 70.8
70
0.8
3.63 21.8 70.8
70
0.8
3.64 21.8 70.8
70
0.8
3.65 21.8 70.8
70
0.8
3.66 21.8 70.8
70
0.8
3.67 21.8 70.8
70
0.8
3.68 21.8 70.8
70
0.8
3.69 21.8 70.8
70
0.8
3.70 21.8 70.8
70
0.8
3.71 21.8 70.8
70
0.8
3.72 21.8 70.8
70
0.8
3.73 21.8 70.8
70
0.8
3.74 21.8 70.8
70
0.8
3.75 21.8 70.8
70
0.8
3.76 21.8 70.8
70
0.8
3.77 21.8 70.8
70
0.8
3.78 21.8 70.8

3.79 21.8 70.8
70
70
0.8
0.8
4
4
Order Number
VAPDSSUSD0380
VAPDSSUSD0381
VAPDSSUSD0382
VAPDSSUSD0383
VAPDSSUSD0384
VAPDSSUSD0385
VAPDSSUSD0386
VAPDSSUSD0387
VAPDSSUSD0388
VAPDSSUSD0389
VAPDSSUSD0390
VAPDSSUSD0391
VAPDSSUSD0392
VAPDSSUSD0393
VAPDSSUSD0394
VAPDSSUSD0395
VAPDSSUSD0396
VAPDSSUSD0397
VAPDSSUSD0398
VAPDSSUSD0399
VAPDSSUSD0400
VAPDSSUSD0405
VAPDSSUSD0410
VAPDSSUSD0415
VAPDSSUSD0420
VAPDSSUSD0425
VAPDSSUSD0430
VAPDSSUSD0435
VAPDSSUSD0440
VAPDSSUSD0445
VAPDSSUSD0450
VAPDSSUSD0455
VAPDSSUSD0460
VAPDSSUSD0465
VAPDSSUSD0470
VAPDSSUSD0475
VAPDSSUSD0480
VAPDSSUSD0485
VAPDSSUSD0490
VAPDSSUSD0495
VAPDSSUSD0500
VAPDSSUSD0505
VAPDSSUSD0510
VAPDSSUSD0515
VAPDSSUSD0520
VAPDSSUSD0525
VAPDSSUSD0530
VAPDSSUSD0535
VAPDSSUSD0540
VAPDSSUSD0545
DC LCF OAL LF
PL DCON
3.80 21.8 70.8

3.81 21.8 70.8
70
70
0.8
0.8
4
4
3.82 21.8 70.8
70
0.8
3.83 21.8 70.8
70
0.8
3.84 21.8 70.8
70
0.8
3.85 21.8 70.8
70
0.8
3.86 21.8 70.8
70
0.8
3.87 21.8 70.8
70
0.8
3.88 21.8 70.8
70
0.8
3.89 21.8 70.8
70
0.8
3.90 21.8 70.8
70
0.8
3.91 21.8 70.8
70
0.8
3.92 21.8 70.8
70
0.8
3.93 21.8 70.8
70
0.8
3.94 21.8 70.8
70
0.8
3.95 21.8 70.8
70
0.8
3.96 21.8 70.8
70
0.8
3.97 21.8 70.8
70
0.8
3.98 21.8 70.8
70
0.8
3.99 21.8 70.8
70
0.8
4.00 21.8 70.8
70
0.8
4.05 21.8 80.8
80
0.8
4.10 21.9 80.9
80
0.9
4.15 21.9 80.9
80
0.9
4.20 21.9 80.9
80
0.9
4.25 21.9 80.9
80
0.9
4.30 23.9 80.9
80
0.9
4.35 23.9 80.9
80
0.9
4.40 23.9 80.9
80
0.9
4.45 23.9 80.9
80
0.9
4.50 23.9 80.9
80
0.9
4.55 23.9 80.9
80
0.9
4.60 26.0 81.0
80
1.0
4.65 26.0 81.0
80
1.0
4.70 26.0 81.0
80
1.0
4.75 26.0 81.0
80
1.0
4.80 26.0 81.0
80
1.0
4.85 26.0 81.0
80
1.0
4.90 26.0 81.0
80
1.0
4.95 26.0 81.0
80
1.0
5.00 26.0 81.0
80
1.0
5.05 26.1 81.1
80
1.1
5.10 26.1 81.1
80
1.1
5.15 26.1 81.1
80
1.1
5.20 26.1 81.1
80
1.1
5.25 26.1 81.1
80
1.1
5.30 26.1 81.1
80
1.1
5.35 28.1 81.1
80
1.1
5.40 28.1 81.1

5.45 28.1 81.1
80
80
1.1
1.1
6
6
CUTTING CONDITIONS
DRILLING
VAPDSSUSD0330
VAPDSSUSD0331
VAPDSSUSD0332
VAPDSSUSD0333
VAPDSSUSD0334
VAPDSSUSD0335
VAPDSSUSD0336
VAPDSSUSD0337
VAPDSSUSD0338
VAPDSSUSD0339
VAPDSSUSD0340
VAPDSSUSD0341
VAPDSSUSD0342
VAPDSSUSD0343
VAPDSSUSD0344
VAPDSSUSD0345
VAPDSSUSD0346
VAPDSSUSD0347
VAPDSSUSD0348
VAPDSSUSD0349
VAPDSSUSD0350
VAPDSSUSD0351
VAPDSSUSD0352
VAPDSSUSD0353
VAPDSSUSD0354
VAPDSSUSD0355
VAPDSSUSD0356
VAPDSSUSD0357
VAPDSSUSD0358
VAPDSSUSD0359
VAPDSSUSD0360
VAPDSSUSD0361
VAPDSSUSD0362
VAPDSSUSD0363
VAPDSSUSD0364
VAPDSSUSD0365
VAPDSSUSD0366
VAPDSSUSD0367
VAPDSSUSD0368
VAPDSSUSD0369
VAPDSSUSD0370
VAPDSSUSD0371
VAPDSSUSD0372
VAPDSSUSD0373
VAPDSSUSD0374
VAPDSSUSD0375
VAPDSSUSD0376
VAPDSSUSD0377
VAPDSSUSD0378
VAPDSSUSD0379
DC LCF OAL LF
Stock
Order Number
Stock
Unit : mm
N158
N149
VIOLET DRILLS
HSS
VAPDSSUS
DRILLING
VAPDSSUSD0550
VAPDSSUSD0555
VAPDSSUSD0560
VAPDSSUSD0565
VAPDSSUSD0570
VAPDSSUSD0575
VAPDSSUSD0580
VAPDSSUSD0585
VAPDSSUSD0590
VAPDSSUSD0595
VAPDSSUSD0600
VAPDSSUSD0605
VAPDSSUSD0610
VAPDSSUSD0615
VAPDSSUSD0620
VAPDSSUSD0625
VAPDSSUSD0630
VAPDSSUSD0635
VAPDSSUSD0640
VAPDSSUSD0645
VAPDSSUSD0650
VAPDSSUSD0655
VAPDSSUSD0660
VAPDSSUSD0665
VAPDSSUSD0670
VAPDSSUSD0675
VAPDSSUSD0680
VAPDSSUSD0685
VAPDSSUSD0690
VAPDSSUSD0695
VAPDSSUSD0700
VAPDSSUSD0705
VAPDSSUSD0710
VAPDSSUSD0715
VAPDSSUSD0720
VAPDSSUSD0725
VAPDSSUSD0730
VAPDSSUSD0735
VAPDSSUSD0740
VAPDSSUSD0745
VAPDSSUSD0750
VAPDSSUSD0755
VAPDSSUSD0760
VAPDSSUSD0765
VAPDSSUSD0770
VAPDSSUSD0775
VAPDSSUSD0780
VAPDSSUSD0785
VAPDSSUSD0790
VAPDSSUSD0795
N150
DC LCF OAL LF
PL DCON
5.50 28.1 81.1

5.55 28.2 81.2
80
80
1.1
1.2
6
6
5.60 28.2 81.2
80
1.2
5.65 28.2 81.2
80
1.2
5.70 28.2 81.2
80
1.2
5.75 28.2 81.2
80
1.2
5.80 28.2 81.2
80
1.2
5.85 28.2 81.2
80
1.2
5.90 28.2 81.2
80
1.2
5.95 28.2 81.2
80
1.2
6.00 28.2 81.2
80
1.2
6.05 31.3 81.3
80
1.3
6.10 31.3 81.3
80
1.3
6.15 31.3 81.3
80
1.3
6.20 31.3 81.3
80
1.3
6.25 31.3 81.3
80
1.3
6.30 31.3 81.3
80
1.3
6.35 31.3 81.3
80
1.3
6.40 31.3 81.3
80
1.3
6.45 31.3 81.3
80
1.3
6.50 31.4 81.4
80
1.4
6.55 31.4 81.4
80
1.4
6.60 31.4 81.4
80
1.4
6.65 31.4 81.4
80
1.4
6.70 31.4 81.4
80
1.4
6.75 33.4 81.4
80
1.4
6.80 33.4 81.4
80
1.4
6.85 33.4 81.4
80
1.4
6.90 33.4 81.4
80
1.4
6.95 33.4 81.4
80
1.4
7.00 33.5 81.5
80
1.5
7.05 33.5 81.5
80
1.5
7.10 33.5 81.5
80
1.5
7.15 33.5 81.5
80
1.5
7.20 33.5 81.5
80
1.5
7.25 33.5 81.5
80
1.5
7.30 33.5 81.5
80
1.5
7.35 33.5 81.5
80
1.5
7.40 33.5 81.5
80
1.5
7.45 33.5 81.5
80
1.5
7.50 33.6 81.6
80
1.6
7.55 36.6 86.6
85
1.6
7.60 36.6 86.6
85
1.6
7.65 36.6 86.6
85
1.6
7.70 36.6 86.6
85
1.6
7.75 36.6 86.6
85
1.6
7.80 36.6 86.6
85
1.6
7.85 36.6 86.6
85
1.6
7.90 36.6 86.6

7.95 36.7 86.7
85
85
1.6
1.7
8
8
Order Number
VAPDSSUSD0800
VAPDSSUSD0805
VAPDSSUSD0810
VAPDSSUSD0815
VAPDSSUSD0820
VAPDSSUSD0825
VAPDSSUSD0830
VAPDSSUSD0835
VAPDSSUSD0840
VAPDSSUSD0845
VAPDSSUSD0850
VAPDSSUSD0855
VAPDSSUSD0860
VAPDSSUSD0865
VAPDSSUSD0870
VAPDSSUSD0875
VAPDSSUSD0880
VAPDSSUSD0885
VAPDSSUSD0890
VAPDSSUSD0895
VAPDSSUSD0900
VAPDSSUSD0910
VAPDSSUSD0920
VAPDSSUSD0930
VAPDSSUSD0940
VAPDSSUSD0950
VAPDSSUSD0960
VAPDSSUSD0970
VAPDSSUSD0980
VAPDSSUSD0990
VAPDSSUSD1000
VAPDSSUSD1010
VAPDSSUSD1020
VAPDSSUSD1030
VAPDSSUSD1040
VAPDSSUSD1050
VAPDSSUSD1060
VAPDSSUSD1070
VAPDSSUSD1080
VAPDSSUSD1090
VAPDSSUSD1100
VAPDSSUSD1110
VAPDSSUSD1120
VAPDSSUSD1130
VAPDSSUSD1140
VAPDSSUSD1150
VAPDSSUSD1160
VAPDSSUSD1170
VAPDSSUSD1180
VAPDSSUSD1190
Stock
Order Number
Stock
Unit : mm
DC LCF OAL LF
PL DCON
8.00 36.7
8.05 36.7
86.7
91.7
85
90
1.7
1.7
8
10
8.10 36.7
91.7
90
1.7
10
8.15 36.7
91.7
90
1.7
10
8.20 36.7
91.7
90
1.7
10
8.25 36.7
91.7
90
1.7
10
8.30 36.7
91.7
90
1.7
10
8.35 36.7
91.7
90
1.7
10
8.40 36.7
91.7
90
1.7
10
8.45 36.8
91.8
90
1.8
10
8.50 36.8
91.8
90
1.8
10
8.55 39.8
94.8
93
1.8
10
8.60 39.8
94.8
93
1.8
10
8.65 39.8
94.8
93
1.8
10
8.70 39.8
94.8
93
1.8
10
8.75 39.8
94.8
93
1.8
10
8.80 39.8
94.8
93
1.8
10
8.85 39.8
94.8
93
1.8
10
8.90 39.8
94.8
93
1.8
10
8.95 39.9
94.9
93
1.9
10
9.00 39.9
94.9
93
1.9
10
9.10 39.9
94.9
93
1.9
10
9.20 39.9
94.9
93
1.9
10
9.30 39.9
94.9
93
1.9
10
9.40 40.0
95.0
93
2.0
10
9.50 40.0
95.0
93
2.0
10
9.60 43.0
98.0
96
2.0
10
9.70 43.0
98.0
96
2.0
10
9.80 43.0
98.0
96
2.0
10
9.90 43.1
98.1
96
2.1
10
98.1
10.0
43.1
96
2.1
10
10.1
43.1 103.1 101
2.1
12
10.2
43.1 103.1 101
2.1
12
10.3
43.1 103.1 101
2.1
12
10.4
43.2 103.2 101
2.2
12
10.5
43.2 103.2 101
2.2
12
10.6
43.2 103.2 101
2.2
12
10.7
47.2 107.2 105
2.2
12
10.8
47.2 107.2 105
2.2
12
10.9
47.3 107.3 105
2.3
12
11.0
47.3 107.3 105
2.3
12
11.1
47.3 107.3 105
2.3
12
11.2
47.3 107.3 105
2.3
12
11.3
47.3 107.3 105
2.3
12
11.4
47.4 107.4 105
2.4
12
11.5
47.4 107.4 105
2.4
12
11.6
47.4 107.4 105
2.4
12
11.7
47.4 107.4 105
2.4
12
11.8
11.9
47.4 107.4 105

51.5 111.5 109
2.4
2.5
12
12
a
a
HSS
Stock
Unit : mm
Order Number
DC LCF OAL LF
PL DCON
VAPDSSUSD1200
VAPDSSUSD1210
VAPDSSUSD1220
VAPDSSUSD1230
VAPDSSUSD1240
VAPDSSUSD1250
VAPDSSUSD1260
VAPDSSUSD1270
VAPDSSUSD1280
VAPDSSUSD1290
VAPDSSUSD1300
VAPDSSUSD1350
VAPDSSUSD1400
VAPDSSUSD1410
VAPDSSUSD1420
VAPDSSUSD1450
VAPDSSUSD1500
VAPDSSUSD1550
VAPDSSUSD1560
VAPDSSUSD1570
VAPDSSUSD1600
VAPDSSUSD1650
VAPDSSUSD1700
VAPDSSUSD1750
VAPDSSUSD1760
VAPDSSUSD1770
VAPDSSUSD1800
VAPDSSUSD1850
VAPDSSUSD1900
VAPDSSUSD1950
VAPDSSUSD1960
VAPDSSUSD1970
VAPDSSUSD2000
12.0 51.5 111.5 109

12.1 51.5 111.5 109
2.5
2.5
12
12
12.2 51.5 111.5 109
2.5
12
12.3 51.6 111.6 109
2.6
12
12.4 51.6 111.6 109
2.6
12
12.5 51.6 111.6 109
2.6
12
12.6 51.6 111.6 109
2.6
12
12.7 51.6 111.6 109
2.6
12
12.8 51.7 111.7 109
2.7
12
12.9 51.7 111.7 109
2.7
12
13.0 51.7 111.7 109
2.7
12
13.5 53.8 113.8 111
2.8
16
14.0 53.9 113.9 111
2.9
16
14.1 55.9 115.9 113
2.9
16
14.2 55.9 115.9 113
2.9
16
14.5 56.0 116.0 113
3.0
16
15.0 56.1 116.1 113
3.1
16
15.5 58.2 118.2 115
3.2
16
15.6 58.2 118.2 115
3.2
16
15.7 58.3 118.3 115
3.3
16
16.0 58.3 118.3 115
3.3
16
16.5 60.4 125.4 122
3.4
20
17.0 60.5 125.5 122
3.5
20
17.5 61.6 126.6 123
3.6
20
17.6 61.7 126.7 123
3.7
20
17.7 61.7 126.7 123
3.7
20
18.0 61.7 126.7 123
3.7
20
18.5 63.8 128.8 125
3.8
20
19.0 63.9 128.9 125
3.9
20
19.5 66.0 131.0 127
4.0
20
19.6 66.1 131.1 127
4.1
20
19.7 66.1 131.1 127

20.0 66.1 131.1 127
4.1
4.1
20
20
DRILLING
CUTTING CONDITIONS
N158
N151
VIOLET DRILLS
HSS
VAPDMSUS
Medium, High precision, For stainless steel
P
Steel
CO HSS
118
135
Thinning
DC<4
DC>4
DC>1
0.5 < DC < 3
3<DC < 6
6<DC < 10
10<DC < 13
0
0.014
0
0.018
0
0.022
0
0.027

*All
and under dia. 4.0mm have a tolerance of 0 -0.009mm.
PL
DCON(h7)
DC
LF
LCF
OAL
a New design and the Violet coating combination enable high
efficiency drilling and long tool life for drilling of stainless steels.
DRILLING
VAPDMSUSD0050
VAPDMSUSD0051
VAPDMSUSD0052
VAPDMSUSD0053
VAPDMSUSD0054
VAPDMSUSD0055
VAPDMSUSD0056
VAPDMSUSD0057
VAPDMSUSD0058
VAPDMSUSD0059
VAPDMSUSD0060
VAPDMSUSD0061
VAPDMSUSD0062
VAPDMSUSD0063
VAPDMSUSD0064
VAPDMSUSD0065
VAPDMSUSD0066
VAPDMSUSD0067
VAPDMSUSD0068
VAPDMSUSD0069
VAPDMSUSD0070
VAPDMSUSD0071
VAPDMSUSD0072
VAPDMSUSD0073
VAPDMSUSD0074
VAPDMSUSD0075
VAPDMSUSD0076
VAPDMSUSD0077
VAPDMSUSD0078
VAPDMSUSD0079
VAPDMSUSD0080
VAPDMSUSD0081
VAPDMSUSD0082
VAPDMSUSD0083
VAPDMSUSD0084
VAPDMSUSD0085
VAPDMSUSD0086
VAPDMSUSD0087
VAPDMSUSD0088
VAPDMSUSD0089
N152
DC LCF OAL LF
PL DCON
0.50
0.51
6.15 50.15
6.15 50.15
50
50
0.15
0.15
3
3
0.52
6.16 50.16
50
0.16
0.53
6.16 50.16
50
0.16
0.54
6.16 50.16
50
0.16
0.55
6.17 50.17
50
0.17
0.56
8.17 50.17
50
0.17
0.57
8.17 50.17
50
0.17
0.58
8.17 50.17
50
0.17
0.59
8.18 50.18
50
0.18
0.60
8.18 50.18
50
0.18
0.61
8.18 50.18
50
0.18
0.62
8.19 50.19
50
0.19
0.63
8.19 50.19
50
0.19
0.64
8.19 50.19
50
0.19
0.65
8.20 50.20
50
0.20
0.66
8.20 50.20
50
0.20
0.67
8.20 50.20
50
0.20
0.68
8.20 50.20
50
0.20
0.69
8.21 50.21
50
0.21
0.70 10.21 50.21
50
0.21
0.71 10.21 50.21
50
0.21
0.72 10.22 50.22
50
0.22
0.73 10.22 50.22
50
0.22
0.74 10.22 50.22
50
0.22
0.75 10.23 50.23
50
0.23
0.76 10.23 50.23
50
0.23
0.77 10.23 50.23
50
0.23
0.78 10.23 50.23
50
0.23
0.79 10.24 50.24
50
0.24
0.80 10.24 50.24
50
0.24
0.81 10.24 50.24
50
0.24
0.82 10.25 50.25
50
0.25
0.83 10.25 50.25
50
0.25
0.84 10.25 50.25
50
0.25
0.85 10.26 50.26
50
0.26
0.86 12.26 50.26
50
0.26
0.87 12.26 50.26
50
0.26
0.88 12.26 50.26

0.89 12.27 50.27
50
50
0.26
0.27
3
3
Order Number
VAPDMSUSD0090
VAPDMSUSD0091
VAPDMSUSD0092
VAPDMSUSD0093
VAPDMSUSD0094
VAPDMSUSD0095
VAPDMSUSD0096
VAPDMSUSD0097
VAPDMSUSD0098
VAPDMSUSD0099
VAPDMSUSD0100
VAPDMSUSD0101
VAPDMSUSD0102
VAPDMSUSD0103
VAPDMSUSD0104
VAPDMSUSD0105
VAPDMSUSD0106
VAPDMSUSD0107
VAPDMSUSD0108
VAPDMSUSD0109
VAPDMSUSD0110
VAPDMSUSD0111
VAPDMSUSD0112
VAPDMSUSD0113
VAPDMSUSD0114
VAPDMSUSD0115
VAPDMSUSD0116
VAPDMSUSD0117
VAPDMSUSD0118
VAPDMSUSD0119
VAPDMSUSD0120
VAPDMSUSD0121
VAPDMSUSD0122
VAPDMSUSD0123
VAPDMSUSD0124
VAPDMSUSD0125
VAPDMSUSD0126
VAPDMSUSD0127
VAPDMSUSD0128
VAPDMSUSD0129
Stock
Order Number
Stock
Unit : mm
DC LCF OAL LF
PL DCON
0.90 12.27 50.27

0.91 12.27 50.27
50
50
0.27
0.27
3
3
0.92 12.28 50.28
50
0.28
0.93 12.28 50.28
50
0.28
0.94 12.28 50.28
50
0.28
0.95 12.29 50.29
50
0.29
0.96 12.29 50.29
50
0.29
0.97 12.29 50.29
50
0.29
0.98 12.29 50.29
50
0.29
0.99 12.30 50.30
50
0.30
1.00 12.3 60.3
60
0.3
1.01 12.3 60.3
60
0.3
1.02 12.3 60.3
60
0.3
1.03 12.3 60.3
60
0.3
1.04 12.3 60.3
60
0.3
1.05 12.3 60.3
60
0.3
1.06 12.3 60.3
60
0.3
1.07 16.3 60.3
60
0.3
1.08 16.3 60.3
60
0.3
1.09 16.3 60.3
60
0.3
1.10 16.3 60.3
60
0.3
1.11 16.3 60.3
60
0.3
1.12 16.3 60.3
60
0.3
1.13 16.3 60.3
60
0.3
1.14 16.3 60.3
60
0.3
1.15 16.4 60.4
60
0.4
1.16 16.4 60.4
60
0.4
1.17 16.4 60.4
60
0.4
1.18 16.4 60.4
60
0.4
1.19 16.4 60.4
60
0.4
1.20 16.4 60.4
60
0.4
1.21 16.4 60.4
60
0.4
1.22 16.4 60.4
60
0.4
1.23 16.4 60.4
60
0.4
1.24 16.4 60.4
60
0.4
1.25 16.4 60.4
60
0.4
1.26 16.4 60.4
60
0.4
1.27 16.4 60.4
60
0.4
1.28 16.4 60.4

1.29 16.4 60.4
60
60
0.4
0.4
3
3
a
a
HSS
PL DCON
1.30 16.4 60.4

1.31 18.4 60.4
60
60
0.4
0.4
3
3
1.32 18.4 60.4
60
0.4
1.33 18.4 60.4
60
0.4
1.34 18.4 60.4
60
0.4
1.35 18.4 60.4
60
0.4
1.36 18.4 60.4
60
0.4
1.37 18.4 60.4
60
0.4
1.38 18.4 60.4
60
0.4
1.39 18.4 60.4
60
0.4
1.40 18.4 60.4
60
0.4
1.41 18.4 60.4
60
0.4
1.42 18.4 60.4
60
0.4
1.43 18.4 60.4
60
0.4
1.44 18.4 60.4
60
0.4
1.45 18.4 60.4
60
0.4
1.46 18.4 60.4
60
0.4
1.47 18.4 60.4
60
0.4
1.48 18.4 60.4
60
0.4
1.49 18.5 60.5
60
0.5
1.50 18.5 60.5
60
0.5
1.51 20.5 60.5
60
0.5
1.52 20.5 60.5
60
0.5
1.53 20.5 60.5
60
0.5
1.54 20.5 60.5
60
0.5
1.55 20.5 60.5
60
0.5
1.56 20.5 60.5
60
0.5
1.57 20.5 60.5
60
0.5
1.58 20.5 60.5
60
0.5
1.59 20.5 60.5
60
0.5
1.60 20.5 60.5
60
0.5
1.61 20.5 60.5
60
0.5
1.62 20.5 60.5
60
0.5
1.63 20.5 60.5
60
0.5
1.64 20.5 60.5
60
0.5
1.65 20.5 60.5
60
0.5
1.66 20.5 60.5
60
0.5
1.67 20.5 60.5
60
0.5
1.68 20.5 60.5
60
0.5
1.69 20.5 60.5
60
0.5
1.70 20.5 60.5
60
0.5
1.71 20.5 60.5
60
0.5
1.72 20.5 60.5
60
0.5
1.73 20.5 60.5
60
0.5
1.74 20.5 60.5
60
0.5
1.75 20.5 60.5
60
0.5
1.76 20.5 60.5
60
0.5
1.77 20.5 60.5
60
0.5
1.78 20.5 60.5

1.79 20.5 60.5
60
60
0.5
0.5
3
3
Order Number
VAPDMSUSD0180
VAPDMSUSD0181
VAPDMSUSD0182
VAPDMSUSD0183
VAPDMSUSD0184
VAPDMSUSD0185
VAPDMSUSD0186
VAPDMSUSD0187
VAPDMSUSD0188
VAPDMSUSD0189
VAPDMSUSD0190
VAPDMSUSD0191
VAPDMSUSD0192
VAPDMSUSD0193
VAPDMSUSD0194
VAPDMSUSD0195
VAPDMSUSD0196
VAPDMSUSD0197
VAPDMSUSD0198
VAPDMSUSD0199
VAPDMSUSD0200
VAPDMSUSD0201
VAPDMSUSD0202
VAPDMSUSD0203
VAPDMSUSD0204
VAPDMSUSD0205
VAPDMSUSD0206
VAPDMSUSD0207
VAPDMSUSD0208
VAPDMSUSD0209
VAPDMSUSD0210
VAPDMSUSD0211
VAPDMSUSD0212
VAPDMSUSD0213
VAPDMSUSD0214
VAPDMSUSD0215
VAPDMSUSD0216
VAPDMSUSD0217
VAPDMSUSD0218
VAPDMSUSD0219
VAPDMSUSD0220
VAPDMSUSD0221
VAPDMSUSD0222
VAPDMSUSD0223
VAPDMSUSD0224
VAPDMSUSD0225
VAPDMSUSD0226
VAPDMSUSD0227
VAPDMSUSD0228
VAPDMSUSD0229
DC LCF OAL LF
PL DCON
1.80 22.5 60.5

1.81 22.5 60.5
60
60
0.5
0.5
3
3
1.82 22.6 60.6
60
0.6
1.83 22.6 60.6
60
0.6
1.84 22.6 60.6
60
0.6
1.85 22.6 60.6
60
0.6
1.86 22.6 60.6
60
0.6
1.87 22.6 60.6
60
0.6
1.88 22.6 60.6
60
0.6
1.89 22.6 60.6
60
0.6
1.90 22.6 60.6
60
0.6
1.91 23.6 60.6
60
0.6
1.92 23.6 60.6
60
0.6
1.93 23.6 60.6
60
0.6
1.94 23.6 60.6
60
0.6
1.95 23.6 60.6
60
0.6
1.96 23.6 60.6
60
0.6
1.97 23.6 60.6
60
0.6
1.98 23.6 60.6
60
0.6
1.99 23.6 60.6
60
0.6
2.00 23.6 70.6
70
0.6
2.01 23.6 70.6
70
0.6
2.02 23.6 70.6
70
0.6
2.03 23.6 70.6
70
0.6
2.04 23.6 70.6
70
0.6
2.05 23.6 70.6
70
0.6
2.06 23.6 70.6
70
0.6
2.07 23.6 70.6
70
0.6
2.08 23.6 70.6
70
0.6
2.09 23.6 70.6
70
0.6
2.10 23.6 70.6
70
0.6
2.11 23.6 70.6
70
0.6
2.12 23.6 70.6
70
0.6
2.13 23.6 70.6
70
0.6
2.14 23.6 70.6
70
0.6
2.15 23.7 70.7
70
0.7
2.16 23.7 70.7
70
0.7
2.17 23.7 70.7
70
0.7
2.18 23.7 70.7
70
0.7
2.19 23.7 70.7
70
0.7
2.20 26.7 70.7
70
0.7
2.21 26.7 70.7
70
0.7
2.22 26.7 70.7
70
0.7
2.23 26.7 70.7
70
0.7
2.24 26.7 70.7
70
0.7
2.25 26.7 70.7
70
0.7
2.26 26.7 70.7
70
0.7
2.27 26.7 70.7
70
0.7
2.28 26.7 70.7

2.29 26.7 70.7
70
70
0.7
0.7
3
3
CUTTING CONDITIONS
DRILLING
VAPDMSUSD0130
VAPDMSUSD0131
VAPDMSUSD0132
VAPDMSUSD0133
VAPDMSUSD0134
VAPDMSUSD0135
VAPDMSUSD0136
VAPDMSUSD0137
VAPDMSUSD0138
VAPDMSUSD0139
VAPDMSUSD0140
VAPDMSUSD0141
VAPDMSUSD0142
VAPDMSUSD0143
VAPDMSUSD0144
VAPDMSUSD0145
VAPDMSUSD0146
VAPDMSUSD0147
VAPDMSUSD0148
VAPDMSUSD0149
VAPDMSUSD0150
VAPDMSUSD0151
VAPDMSUSD0152
VAPDMSUSD0153
VAPDMSUSD0154
VAPDMSUSD0155
VAPDMSUSD0156
VAPDMSUSD0157
VAPDMSUSD0158
VAPDMSUSD0159
VAPDMSUSD0160
VAPDMSUSD0161
VAPDMSUSD0162
VAPDMSUSD0163
VAPDMSUSD0164
VAPDMSUSD0165
VAPDMSUSD0166
VAPDMSUSD0167
VAPDMSUSD0168
VAPDMSUSD0169
VAPDMSUSD0170
VAPDMSUSD0171
VAPDMSUSD0172
VAPDMSUSD0173
VAPDMSUSD0174
VAPDMSUSD0175
VAPDMSUSD0176
VAPDMSUSD0177
VAPDMSUSD0178
VAPDMSUSD0179
DC LCF OAL LF
Stock
Order Number
Stock
Unit : mm
N158
N153
VIOLET DRILLS
HSS
VAPDMSUS
DRILLING
VAPDMSUSD0230
VAPDMSUSD0231
VAPDMSUSD0232
VAPDMSUSD0233
VAPDMSUSD0234
VAPDMSUSD0235
VAPDMSUSD0236
VAPDMSUSD0237
VAPDMSUSD0238
VAPDMSUSD0239
VAPDMSUSD0240
VAPDMSUSD0241
VAPDMSUSD0242
VAPDMSUSD0243
VAPDMSUSD0244
VAPDMSUSD0245
VAPDMSUSD0246
VAPDMSUSD0247
VAPDMSUSD0248
VAPDMSUSD0249
VAPDMSUSD0250
VAPDMSUSD0251
VAPDMSUSD0252
VAPDMSUSD0253
VAPDMSUSD0254
VAPDMSUSD0255
VAPDMSUSD0256
VAPDMSUSD0257
VAPDMSUSD0258
VAPDMSUSD0259
VAPDMSUSD0260
VAPDMSUSD0261
VAPDMSUSD0262
VAPDMSUSD0263
VAPDMSUSD0264
VAPDMSUSD0265
VAPDMSUSD0266
VAPDMSUSD0267
VAPDMSUSD0268
VAPDMSUSD0269
VAPDMSUSD0270
VAPDMSUSD0271
VAPDMSUSD0272
VAPDMSUSD0273
VAPDMSUSD0274
VAPDMSUSD0275
VAPDMSUSD0276
VAPDMSUSD0277
VAPDMSUSD0278
VAPDMSUSD0279
N154
DC LCF OAL LF
PL DCON
2.30 26.7 70.7

2.31 26.7 70.7
70
70
0.7
0.7
3
3
2.32 26.7 70.7
70
0.7
2.33 26.7 70.7
70
0.7
2.34 26.7 70.7
70
0.7
2.35 26.7 70.7
70
0.7
2.36 26.7 70.7
70
0.7
2.37 26.7 70.7
70
0.7
2.38 26.7 70.7
70
0.7
2.39 26.7 70.7
70
0.7
2.40 29.7 70.7
70
0.7
2.41 29.7 70.7
70
0.7
2.42 29.7 70.7
70
0.7
2.43 29.7 70.7
70
0.7
2.44 29.7 70.7
70
0.7
2.45 29.7 70.7
70
0.7
2.46 29.7 70.7
70
0.7
2.47 29.7 70.7
70
0.7
2.48 29.8 70.8
70
0.8
2.49 29.8 70.8
70
0.8
2.50 29.8 70.8
70
0.8
2.51 29.8 70.8
70
0.8
2.52 29.8 70.8
70
0.8
2.53 29.8 70.8
70
0.8
2.54 29.8 70.8
70
0.8
2.55 29.8 70.8
70
0.8
2.56 29.8 70.8
70
0.8
2.57 29.8 70.8
70
0.8
2.58 29.8 70.8
70
0.8
2.59 29.8 70.8
70
0.8
2.60 29.8 70.8
70
0.8
2.61 29.8 70.8
70
0.8
2.62 29.8 70.8
70
0.8
2.63 29.8 70.8
70
0.8
2.64 29.8 70.8
70
0.8
2.65 29.8 70.8
70
0.8
2.66 29.8 70.8
70
0.8
2.67 29.8 70.8
70
0.8
2.68 29.8 70.8
70
0.8
2.69 29.8 70.8
70
0.8
2.70 32.8 70.8
70
0.8
2.71 32.8 70.8
70
0.8
2.72 32.8 70.8
70
0.8
2.73 32.8 70.8
70
0.8
2.74 32.8 70.8
70
0.8
2.75 32.8 70.8
70
0.8
2.76 32.8 70.8
70
0.8
2.77 32.8 70.8
70
0.8
2.78 32.8 70.8

2.79 32.8 70.8
70
70
0.8
0.8
3
3
Order Number
VAPDMSUSD0280
VAPDMSUSD0281
VAPDMSUSD0282
VAPDMSUSD0283
VAPDMSUSD0284
VAPDMSUSD0285
VAPDMSUSD0286
VAPDMSUSD0287
VAPDMSUSD0288
VAPDMSUSD0289
VAPDMSUSD0290
VAPDMSUSD0291
VAPDMSUSD0292
VAPDMSUSD0293
VAPDMSUSD0294
VAPDMSUSD0295
VAPDMSUSD0296
VAPDMSUSD0297
VAPDMSUSD0298
VAPDMSUSD0299
VAPDMSUSD0300
VAPDMSUSD0301
VAPDMSUSD0302
VAPDMSUSD0303
VAPDMSUSD0304
VAPDMSUSD0305
VAPDMSUSD0306
VAPDMSUSD0307
VAPDMSUSD0308
VAPDMSUSD0309
VAPDMSUSD0310
VAPDMSUSD0311
VAPDMSUSD0312
VAPDMSUSD0313
VAPDMSUSD0314
VAPDMSUSD0315
VAPDMSUSD0316
VAPDMSUSD0317
VAPDMSUSD0318
VAPDMSUSD0319
VAPDMSUSD0320
VAPDMSUSD0321
VAPDMSUSD0322
VAPDMSUSD0323
VAPDMSUSD0324
VAPDMSUSD0325
VAPDMSUSD0326
VAPDMSUSD0327
VAPDMSUSD0328
VAPDMSUSD0329
Stock
Order Number
Stock
Unit : mm
DC LCF OAL LF
PL DCON
2.80 32.8 70.8

2.81 32.8 70.8
70
70
0.8
0.8
3
3
2.82 32.9 70.9
70
0.9
2.83 32.9 70.9
70
0.9
2.84 32.9 70.9
70
0.9
2.85 32.9 70.9
70
0.9
2.86 32.9 70.9
70
0.9
2.87 32.9 70.9
70
0.9
2.88 32.9 70.9
70
0.9
2.89 32.9 70.9
70
0.9
2.90 32.9 70.9
70
0.9
2.91 32.9 70.9
70
0.9
2.92 32.9 70.9
70
0.9
2.93 32.9 70.9
70
0.9
2.94 32.9 70.9
70
0.9
2.95 32.9 70.9
70
0.9
2.96 32.9 70.9
70
0.9
2.97 32.9 70.9
70
0.9
2.98 32.9 70.9
70
0.9
2.99 32.9 70.9
70
0.9
3.00 32.9 70.9
70
0.9
3.01 35.9 85.9
85
0.9
3.02 35.9 85.9
85
0.9
3.03 35.9 85.9
85
0.9
3.04 35.9 85.9
85
0.9
3.05 35.9 85.9
85
0.9
3.06 35.9 85.9
85
0.9
3.07 35.9 85.9
85
0.9
3.08 35.9 85.9
85
0.9
3.09 35.9 85.9
85
0.9
3.10 35.9 85.9
85
0.9
3.11 35.9 85.9
85
0.9
3.12 35.9 85.9
85
0.9
3.13 35.9 85.9
85
0.9
3.14 35.9 85.9
85
0.9
3.15 36.0 86.0
85
1.0
3.16 36.0 86.0
85
1.0
3.17 36.0 86.0
85
1.0
3.18 36.0 86.0
85
1.0
3.19 36.0 86.0
85
1.0
3.20 36.0 86.0
85
1.0
3.21 36.0 86.0
85
1.0
3.22 36.0 86.0
85
1.0
3.23 36.0 86.0
85
1.0
3.24 36.0 86.0
85
1.0
3.25 36.0 86.0
85
1.0
3.26 36.0 86.0
85
1.0
3.27 36.0 86.0
85
1.0
3.28 36.0 86.0

3.29 36.0 86.0
85
85
1.0
1.0
4
4
a
a
HSS
PL DCON
3.30 36.0 86.0

3.31 39.0 86.0
85
85
1.0
1.0
4
4
3.32 39.0 86.0
85
1.0
3.33 39.0 86.0
85
1.0
3.34 39.0 86.0
85
1.0
3.35 39.0 86.0
85
1.0
3.36 39.0 86.0
85
1.0
3.37 39.0 86.0
85
1.0
3.38 39.0 86.0
85
1.0
3.39 39.0 86.0
85
1.0
3.40 39.0 86.0
85
1.0
3.41 39.0 86.0
85
1.0
3.42 39.0 86.0
85
1.0
3.43 39.0 86.0
85
1.0
3.44 39.0 86.0
85
1.0
3.45 39.0 86.0
85
1.0
3.46 39.0 86.0
85
1.0
3.47 39.0 86.0
85
1.0
3.48 39.1 86.1
85
1.1
3.49 39.1 86.1
85
1.1
3.50 39.1 86.1
85
1.1
3.51 39.1 86.1
85
1.1
3.52 39.1 86.1
85
1.1
3.53 39.1 86.1
85
1.1
3.54 39.1 86.1
85
1.1
3.55 39.1 86.1
85
1.1
3.56 39.1 86.1
85
1.1
3.57 39.1 86.1
85
1.1
3.58 39.1 86.1
85
1.1
3.59 39.1 86.1
85
1.1
3.60 39.1 86.1
85
1.1
3.61 39.1 86.1
85
1.1
3.62 39.1 86.1
85
1.1
3.63 39.1 86.1
85
1.1
3.64 39.1 86.1
85
1.1
3.65 39.1 86.1
85
1.1
3.66 39.1 86.1
85
1.1
3.67 39.1 86.1
85
1.1
3.68 39.1 86.1
85
1.1
3.69 39.1 86.1
85
1.1
3.70 39.1 86.1
85
1.1
3.71 43.1 86.1
85
1.1
3.72 43.1 86.1
85
1.1
3.73 43.1 86.1
85
1.1
3.74 43.1 86.1
85
1.1
3.75 43.1 86.1
85
1.1
3.76 43.1 86.1
85
1.1
3.77 43.1 86.1
85
1.1
3.78 43.1 86.1

3.79 43.1 86.1
85
85
1.1
1.1
4
4
Order Number
VAPDMSUSD0380
VAPDMSUSD0381
VAPDMSUSD0382
VAPDMSUSD0383
VAPDMSUSD0384
VAPDMSUSD0385
VAPDMSUSD0386
VAPDMSUSD0387
VAPDMSUSD0388
VAPDMSUSD0389
VAPDMSUSD0390
VAPDMSUSD0391
VAPDMSUSD0392
VAPDMSUSD0393
VAPDMSUSD0394
VAPDMSUSD0395
VAPDMSUSD0396
VAPDMSUSD0397
VAPDMSUSD0398
VAPDMSUSD0399
VAPDMSUSD0400
VAPDMSUSD0405
VAPDMSUSD0410
VAPDMSUSD0415
VAPDMSUSD0420
VAPDMSUSD0425
VAPDMSUSD0430
VAPDMSUSD0435
VAPDMSUSD0440
VAPDMSUSD0445
VAPDMSUSD0450
VAPDMSUSD0455
VAPDMSUSD0460
VAPDMSUSD0465
VAPDMSUSD0470
VAPDMSUSD0475
VAPDMSUSD0480
VAPDMSUSD0485
VAPDMSUSD0490
VAPDMSUSD0495
VAPDMSUSD0500
VAPDMSUSD0505
VAPDMSUSD0510
VAPDMSUSD0515
VAPDMSUSD0520
VAPDMSUSD0525
VAPDMSUSD0530
VAPDMSUSD0535
VAPDMSUSD0540
VAPDMSUSD0545
DC LCF OAL LF
PL DCON
3.80 43.1
3.81 43.1
86.1
86.1
85
85
1.1
1.1
4
4
3.82 43.2
86.2
85
1.2
3.83 43.2
86.2
85
1.2
3.84 43.2
86.2
85
1.2
3.85 43.2
86.2
85
1.2
3.86 43.2
86.2
85
1.2
3.87 43.2
86.2
85
1.2
3.88 43.2
86.2
85
1.2
3.89 43.2
86.2
85
1.2
3.90 43.2
86.2
85
1.2
3.91 43.2
86.2
85
1.2
3.92 43.2
86.2
85
1.2
3.93 43.2
86.2
85
1.2
3.94 43.2
86.2
85
1.2
3.95 43.2
86.2
85
1.2
3.96 43.2
86.2
85
1.2
3.97 43.2
86.2
85
1.2
3.98 43.2
86.2
85
1.2
3.99 43.2
86.2
85
1.2
4.00 42.8
85.8
85
0.8
4.05 42.8 100.8 100
0.8
4.10 42.9 100.9 100
0.9
4.15 42.9 100.9 100
0.9
4.20 42.9 100.9 100
0.9
4.25 46.9 100.9 100
0.9
4.30 46.9 100.9 100
0.9
4.35 46.9 100.9 100
0.9
4.40 46.9 100.9 100
0.9
4.45 46.9 100.9 100
0.9
4.50 46.9 100.9 100
0.9
4.55 46.9 100.9 100
0.9
4.60 47.0 101.0 100
1.0
4.65 47.0 101.0 100
1.0
4.70 47.0 101.0 100
1.0
4.75 47.0 101.0 100
1.0
4.80 52.0 101.0 100
1.0
4.85 52.0 101.0 100
1.0
4.90 52.0 101.0 100
1.0
4.95 52.0 101.0 100
1.0
5.00 52.0 101.0 100
1.0
5.05 52.1 101.1 100
1.1
5.10 52.1 101.1 100
1.1
5.15 52.1 101.1 100
1.1
5.20 52.1 101.1 100
1.1
5.25 52.1 101.1 100
1.1
5.30 52.1 101.1 100
1.1
5.35 57.1 107.1 106
1.1
5.40 57.1 107.1 106

5.45 57.1 107.1 106
1.1
1.1
6
6
CUTTING CONDITIONS
DRILLING
VAPDMSUSD0330
VAPDMSUSD0331
VAPDMSUSD0332
VAPDMSUSD0333
VAPDMSUSD0334
VAPDMSUSD0335
VAPDMSUSD0336
VAPDMSUSD0337
VAPDMSUSD0338
VAPDMSUSD0339
VAPDMSUSD0340
VAPDMSUSD0341
VAPDMSUSD0342
VAPDMSUSD0343
VAPDMSUSD0344
VAPDMSUSD0345
VAPDMSUSD0346
VAPDMSUSD0347
VAPDMSUSD0348
VAPDMSUSD0349
VAPDMSUSD0350
VAPDMSUSD0351
VAPDMSUSD0352
VAPDMSUSD0353
VAPDMSUSD0354
VAPDMSUSD0355
VAPDMSUSD0356
VAPDMSUSD0357
VAPDMSUSD0358
VAPDMSUSD0359
VAPDMSUSD0360
VAPDMSUSD0361
VAPDMSUSD0362
VAPDMSUSD0363
VAPDMSUSD0364
VAPDMSUSD0365
VAPDMSUSD0366
VAPDMSUSD0367
VAPDMSUSD0368
VAPDMSUSD0369
VAPDMSUSD0370
VAPDMSUSD0371
VAPDMSUSD0372
VAPDMSUSD0373
VAPDMSUSD0374
VAPDMSUSD0375
VAPDMSUSD0376
VAPDMSUSD0377
VAPDMSUSD0378
VAPDMSUSD0379
DC LCF OAL LF
Stock
Order Number
Stock
Unit : mm
N158
N155
VIOLET DRILLS
HSS
VAPDMSUS
DRILLING
DC LCF OAL LF
PL DCON
VAPDMSUSD0550
VAPDMSUSD0555
VAPDMSUSD0560
VAPDMSUSD0565
VAPDMSUSD0570
VAPDMSUSD0575
VAPDMSUSD0580
VAPDMSUSD0585
VAPDMSUSD0590
VAPDMSUSD0595
VAPDMSUSD0600
VAPDMSUSD0605
VAPDMSUSD0610
VAPDMSUSD0615
VAPDMSUSD0620
VAPDMSUSD0625
VAPDMSUSD0630
VAPDMSUSD0635
VAPDMSUSD0640
VAPDMSUSD0645
VAPDMSUSD0650
VAPDMSUSD0655
VAPDMSUSD0660
VAPDMSUSD0665
VAPDMSUSD0670
VAPDMSUSD0675
VAPDMSUSD0680
VAPDMSUSD0685
VAPDMSUSD0690
VAPDMSUSD0695
VAPDMSUSD0700
VAPDMSUSD0705
VAPDMSUSD0710
VAPDMSUSD0715
VAPDMSUSD0720
VAPDMSUSD0725
VAPDMSUSD0730
VAPDMSUSD0735
VAPDMSUSD0740
VAPDMSUSD0745
VAPDMSUSD0750
VAPDMSUSD0755
VAPDMSUSD0760
VAPDMSUSD0765
VAPDMSUSD0770
VAPDMSUSD0775
VAPDMSUSD0780
VAPDMSUSD0785
VAPDMSUSD0790
VAPDMSUSD0795
5.50 57.1 107.1 106

5.55 57.2 107.2 106
1.1
1.2
6
6
5.60 57.2 107.2 106
1.2
5.65 57.2 107.2 106
1.2
5.70 57.2 107.2 106
1.2
5.75 57.2 107.2 106
1.2
5.80 57.2 107.2 106
1.2
5.85 57.2 107.2 106
1.2
5.90 57.2 107.2 106
1.2
5.95 57.2 107.2 106
1.2
6.00 57.2 107.2 106
1.2
6.05 63.3 113.3 112
1.3
6.10 63.3 113.3 112
1.3
6.15 63.3 113.3 112
1.3
6.20 63.3 113.3 112
1.3
6.25 63.3 113.3 112
1.3
6.30 63.3 113.3 112
1.3
6.35 63.3 113.3 112
1.3
6.40 63.3 113.3 112
1.3
6.45 63.3 113.3 112
1.3
6.50 63.4 113.4 112
1.4
6.55 63.4 113.4 112
1.4
6.60 63.4 113.4 112
1.4
6.65 63.4 113.4 112
1.4
6.70 63.4 113.4 112
1.4
6.75 68.4 118.4 117
1.4
6.80 68.4 118.4 117
1.4
6.85 68.4 118.4 117
1.4
6.90 68.4 118.4 117
1.4
6.95 68.4 118.4 117
1.4
7.00 68.5 118.5 117
1.5
7.05 68.5 118.5 117
1.5
7.10 68.5 118.5 117
1.5
7.15 68.5 118.5 117
1.5
7.20 68.5 118.5 117
1.5
7.25 68.5 118.5 117
1.5
7.30 68.5 118.5 117
1.5
7.35 68.5 118.5 117
1.5
7.40 68.5 118.5 117
1.5
7.45 68.5 118.5 117
1.5
7.50 68.6 118.6 117
1.6
7.55 74.6 124.6 123
1.6
7.60 74.6 124.6 123
1.6
7.65 74.6 124.6 123
1.6
7.70 74.6 124.6 123
1.6
7.75 74.6 124.6 123
1.6
7.80 74.6 124.6 123
1.6
7.85 74.6 124.6 123
1.6
7.90 74.6 124.6 123

7.95 74.7 124.7 123
1.6
1.7
8
8
Stock
Order Number
N156
Stock
Unit : mm
Order Number
DC LCF OAL LF
PL DCON
VAPDMSUSD0800
VAPDMSUSD0805
VAPDMSUSD0810
VAPDMSUSD0815
VAPDMSUSD0820
VAPDMSUSD0825
VAPDMSUSD0830
VAPDMSUSD0835
VAPDMSUSD0840
VAPDMSUSD0845
VAPDMSUSD0850
VAPDMSUSD0855
VAPDMSUSD0860
VAPDMSUSD0865
VAPDMSUSD0870
VAPDMSUSD0875
VAPDMSUSD0880
VAPDMSUSD0885
VAPDMSUSD0890
VAPDMSUSD0895
VAPDMSUSD0900
VAPDMSUSD0910
VAPDMSUSD0920
VAPDMSUSD0930
VAPDMSUSD0940
VAPDMSUSD0950
VAPDMSUSD0960
VAPDMSUSD0970
VAPDMSUSD0980
VAPDMSUSD0990
VAPDMSUSD1000
VAPDMSUSD1010
VAPDMSUSD1020
VAPDMSUSD1030
VAPDMSUSD1040
VAPDMSUSD1050
VAPDMSUSD1060
VAPDMSUSD1070
VAPDMSUSD1080
VAPDMSUSD1090
VAPDMSUSD1100
VAPDMSUSD1110
VAPDMSUSD1120
VAPDMSUSD1130
VAPDMSUSD1140
VAPDMSUSD1150
VAPDMSUSD1160
VAPDMSUSD1170
VAPDMSUSD1180
VAPDMSUSD1190
8.00 74.7 124.7 123

8.05 74.7 129.7 128
1.7
1.7
8
10
8.10 74.7 129.7 128
1.7
10
8.15 74.7 129.7 128
1.7
10
8.20 74.7 129.7 128
1.7
10
8.25 74.7 129.7 128
1.7
10
8.30 74.7 129.7 128
1.7
10
8.35 74.7 129.7 128
1.7
10
8.40 74.7 129.7 128
1.7
10
8.45 74.8 129.8 128
1.8
10
8.50 74.8 129.8 128
1.8
10
8.55 80.8 135.8 134
1.8
10
8.60 80.8 135.8 134
1.8
10
8.65 80.8 135.8 134
1.8
10
8.70 80.8 135.8 134
1.8
10
8.75 80.8 135.8 134
1.8
10
8.80 80.8 135.8 134
1.8
10
8.85 80.8 135.8 134
1.8
10
8.90 80.8 135.8 134
1.8
10
8.95 80.9 135.9 134
1.9
10
9.00 80.9 135.9 134
1.9
10
9.10 80.9 135.9 134
1.9
10
9.20 80.9 135.9 134
1.9
10
9.30 80.9 135.9 134
1.9
10
9.40 81.0 136.0 134
2.0
10
9.50 81.0 136.0 134
2.0
10
9.60 87.0 142.0 140
2.0
10
9.70 87.0 142.0 140
2.0
10
9.80 87.0 142.0 140
2.0
10
9.90 87.1 142.1 140
2.1
10
10.0
87.1 142.1 140
2.1
10
10.1
87.1 147.1 145
2.1
12
10.2
87.1 147.1 145
2.1
12
10.3
87.1 147.1 145
2.1
12
10.4
87.2 147.2 145
2.2
12
10.5
87.2 147.2 145
2.2
12
10.6
87.2 147.2 145
2.2
12
10.7
94.2 154.2 152
2.2
12
10.8
94.2 154.2 152
2.2
12
10.9
94.3 154.3 152
2.3
12
11.0
94.3 154.3 152
2.3
12
11.1
94.3 154.3 152
2.3
12
11.2
94.3 154.3 152
2.3
12
11.3
94.3 154.3 152
2.3
12
11.4
94.4 154.4 152
2.4
12
11.5
94.4 154.4 152
2.4
12
11.6
94.4 154.4 152
2.4
12
11.7
94.4 154.4 152
2.4
12
11.8 94.4 154.4 152

11.9 101.5 161.5 159
2.4
2.5
12
12
a
a
HSS
Stock
Unit : mm
Order Number
DC LCF OAL LF
PL DCON
VAPDMSUSD1200
VAPDMSUSD1210
VAPDMSUSD1220
VAPDMSUSD1230
VAPDMSUSD1240
VAPDMSUSD1250
VAPDMSUSD1260
VAPDMSUSD1270
VAPDMSUSD1280
VAPDMSUSD1290
VAPDMSUSD1300
12.0 101.5 161.5 159

12.1 101.5 161.5 159
2.5
2.5
12
12
12.2 101.5 161.5 159
2.5
12
12.3 101.6 161.6 159
2.6
12
12.4 101.6 161.6 159
2.6
12
12.5 101.6 161.6 159
2.6
12
12.6 101.6 161.6 159
2.6
12
12.7 101.6 161.6 159
2.6
12
12.8 101.7 161.7 159
2.7
12
12.9 101.7 161.7 159

13.0 101.7 161.7 159
2.7
2.7
12
12
DRILLING
CUTTING CONDITIONS
N158
N157
VIOLET DRILLS
HSS
VAPDSSUS
VAPDMSUS
VIOLET DRILLS, High precision, For stainless steel, Short/medium

Stainless steel
Work
Material
Drill Dia.
DC (mm)
Austenitic
AISI 304, AISI 316
Martensitic
Ferritic AISI 430
Structural steel
Aluminium alloy

Alloy steel SCM
Cast iron FC
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
0.5
1.0
7600
4800
0.01
0.02
8800
6300
0.01
0.05
11250
10000
0.01
0.05
15000
12000
0.02
0.05
2.0
2400
0.04
3200
0.06
5500
0.09
6400
0.09
3.0
1600
0.07
2100
0.10
3700
0.13
4300
0.13
4.0
5.0
6.0
8.0
10.0
12.0
13.0
14.0
1200
950
800
600
480
400
370
340
0.09
0.12
0.14
0.18
0.22
0.24
0.26
0.30
1600
1300
1100
800
640
530
490
450
0.10
0.13
0.15
0.18
0.21
0.25
0.28
0.27
2800
2200
1800
1400
1100
930
860
730
0.15
0.18
0.20
0.22
0.25
0.30
0.32
0.31
3200
2600
2100
1600
1300
1100
1000
930
0.15
0.18
0.19
0.24
0.28
0.34
0.36
0.36
15.0
320
0.31
425
0.28
680
0.32
870
0.38
16.0
300
0.32
400
0.30
640
0.34
820
0.42
18.0
20.0
270
240
0.34
0.36
350
320
0.32
0.35
570
510
0.36
0.38
725
660
0.43
0.45
4) For precipitation-hardened stainless steels (JIS SUS630 and SUS631), MWE and MWS are recommended.
DRILLING
N158
VAPDSCB
Short flute length, High precision, For counter boring
K
118
Thinning
HSS
DC < 3 3<DC < 6 6<DC < 10 10<DC < 18 18<DC < 30 30<DC < 32
0
0.014
0
0.018
0
0.022
PL
0
0.027
0
0.033
0
0.039
LF
DC
DC_2
Steel
180
DCON(h7)
HG HSS
LCF
a Unique geometry offers high efficiency counter boring.
Excellent chip breaking and flat counterbored surface.
VAPDSCBD0200
VAPDSCBD0210
VAPDSCBD0220
VAPDSCBD0230
VAPDSCBD0240
VAPDSCBD0250
VAPDSCBD0260
VAPDSCBD0270
VAPDSCBD0280
VAPDSCBD0290
VAPDSCBD0300
VAPDSCBD0310
VAPDSCBD0320
VAPDSCBD0330
VAPDSCBD0340
VAPDSCBD0350
VAPDSCBD0360
VAPDSCBD0370
VAPDSCBD0380
VAPDSCBD0390
VAPDSCBD0400
VAPDSCBD0410
VAPDSCBD0420
VAPDSCBD0430
VAPDSCBD0440
VAPDSCBD0450
VAPDSCBD0460
VAPDSCBD0470
VAPDSCBD0480
VAPDSCBD0490
VAPDSCBD0500
VAPDSCBD0510
VAPDSCBD0520
VAPDSCBD0530
VAPDSCBD0540
VAPDSCBD0550
VAPDSCBD0560
VAPDSCBD0570
VAPDSCBD0580
VAPDSCBD0590
2.0
2.1
0.7
0.7
2.2
DC_2 LCF
LF
PL
DCON
12
12
60
60
0.2
0.2
3
3
0.7
12
60
0.2
2.3
0.7
13
60
0.2
2.4
0.7
13
60
0.2
2.5
0.7
13
60
0.2
2.6
0.8
15
60
0.2
2.7
0.8
15
60
0.2
2.8
0.8
15
60
0.2
2.9
0.8
15
60
0.2
3.0
0.8
15
60
0.2
3.1
0.8
17
70
0.2
3.2
0.8
17
70
0.2
3.3
0.8
19
70
0.2
3.4
0.8
19
70
0.2
3.5
0.8
19
70
0.2
3.6
1.0
21
70
0.2
3.7
1.0
21
70
0.2
3.8
1.0
21
70
0.2
3.9
1.0
21
70
0.2
4.0
1.0
21
70
0.3
4.1
1.0
21
80
0.3
4.2
1.0
21
80
0.3
4.3
1.0
23
80
0.3
4.4
1.0
23
80
0.3
4.5
1.0
23
80
0.3
4.6
1.4
25
80
0.3
4.7
1.4
25
80
0.3
4.8
1.4
25
80
0.3
4.9
1.4
25
80
0.3
5.0
1.4
25
80
0.4
5.1
1.4
25
80
0.4
5.2
1.4
25
80
0.4
5.3
1.4
25
80
0.4
5.4
1.4
27
80
0.4
5.5
1.4
27
80
0.4
5.6
1.4
27
80
0.4
5.7
1.4
27
80
0.4
5.8
5.9
1.4
1.4
27
27
80
80
0.4
0.4
6
6
Order Number
DC
VAPDSCBD0600
VAPDSCBD0610
VAPDSCBD0620
VAPDSCBD0630
VAPDSCBD0640
VAPDSCBD0650
VAPDSCBD0660
VAPDSCBD0670
VAPDSCBD0680
VAPDSCBD0690
VAPDSCBD0700
VAPDSCBD0710
VAPDSCBD0720
VAPDSCBD0730
VAPDSCBD0740
VAPDSCBD0750
VAPDSCBD0760
VAPDSCBD0770
VAPDSCBD0780
VAPDSCBD0790
VAPDSCBD0800
VAPDSCBD0810
VAPDSCBD0850
VAPDSCBD0860
VAPDSCBD0880
VAPDSCBD0900
VAPDSCBD0910
VAPDSCBD0950
VAPDSCBD0960
VAPDSCBD0980
VAPDSCBD1000
VAPDSCBD1010
VAPDSCBD1030
VAPDSCBD1050
VAPDSCBD1080
VAPDSCBD1100
VAPDSCBD1110
VAPDSCBD1150
VAPDSCBD1180
VAPDSCBD1200
6.0
6.1
1.4
1.4
27
30
6.2
1.4
6.3
6.4
DC_2 LCF
LF
PL
DCON
80
80
0.4
0.4
6
8
30
80
0.4
1.4
30
80
0.4
1.4
30
80
0.4
6.5
1.4
30
80
0.4
6.6
1.8
30
80
0.4
6.7
1.8
30
80
0.4
6.8
1.8
32
80
0.4
6.9
1.8
32
80
0.4
7.0
1.8
32
80
0.6
7.1
1.8
32
80
0.6
7.2
1.8
32
80
0.6
7.3
1.8
32
80
0.6
7.4
1.8
32
80
0.6
7.5
1.8
32
80
0.6
7.6
2.0
35
85
0.6
7.7
2.0
35
85
0.6
7.8
2.0
35
85
0.6
7.9
2.0
35
85
0.6
8.0
2.0
35
85
0.6
8.1
2.0
35
90
0.6
10
8.5
2.0
35
90
0.6
10
8.6
2.8
38
93
0.6
10
8.8
2.8
38
93
0.6
10
9.0
2.8
38
93
0.8
10
9.1
2.8
38
93
0.8
10
9.5
2.8
38
93
0.8
10
9.6
3.2
41
96
0.8
10
9.8
3.2
41
96
0.8
10
10.0
3.2
41
96
0.9
10
10.1
3.2
41
101
0.9
12
10.3
3.2
41
101
0.9
12
10.5
3.2
41
101
0.9
12
10.8
3.7
45
105
0.9
12
11.0
3.7
45
105
0.9
12
11.1
3.7
45
105
0.9
12
11.5
3.7
45
105
0.9
12
11.8
12.0
3.7
3.7
45
49
105
109
0.9
0.9
12
12
DRILLING
DC
Stock
Order Number
Stock
Unit : mm

CUTTING CONDITIONS
N161
N159
VIOLET DRILLS
HSS
VAPDSCB
Short flute length, High precision, For counter boring
Order Number
DC
VAPDSCBD1250
VAPDSCBD1300
VAPDSCBD1350
VAPDSCBD1380
VAPDSCBD1400
VAPDSCBD1410
VAPDSCBD1420
VAPDSCBD1450
VAPDSCBD1480
VAPDSCBD1500
VAPDSCBD1550
VAPDSCBD1570
VAPDSCBD1580
VAPDSCBD1600
VAPDSCBD1700
VAPDSCBD1750
VAPDSCBD1760
VAPDSCBD1770
VAPDSCBD1780
VAPDSCBD1800
VAPDSCBD1810
VAPDSCBD1900
VAPDSCBD1980
VAPDSCBD2000
VAPDSCBD2010
VAPDSCBD2100
VAPDSCBD2200
VAPDSCBD2300
VAPDSCBD2400
VAPDSCBD2500
VAPDSCBD2600
VAPDSCBD2700
VAPDSCBD2800
VAPDSCBD2900
VAPDSCBD3000
VAPDSCBD3100
VAPDSCBD3200
12.5
13.0
3.7
4.2
13.5
LF
PL
DCON
49
49
109
109
0.9
1.1
12
12
4.2
51
121
1.1
16
13.8
4.2
51
121
1.1
16
14.0
4.2
51
121
1.1
16
14.1
5.5
58
123
1.1
16
14.2
5.5
58
123
1.1
16
14.5
5.5
58
123
1.1
16
14.8
5.5
58
123
1.1
16
15.0
5.5
58
123
1.3
16
15.5
5.5
60
125
1.3
16
15.7
5.5
60
125
1.3
16
15.8
5.5
60
125
1.3
16
16.0
5.5
60
125
1.3
16
17.0
5.5
62
132
1.3
20
17.5
5.5
63
133
1.6
20
17.6
6.5
63
133
1.6
20
17.7
6.5
63
133
1.6
20
17.8
6.5
63
133
1.6
20
18.0
6.5
63
133
1.6
20
18.1
6.5
65
135
1.6
20
19.0
6.5
65
135
1.6
20
19.8
7.5
67
137
1.6
20
20.0
7.5
67
137
1.8
20
20.1
7.5
67
137
1.8
20
21.0
7.5
75
165
1.8
25
22.0
7.5
75
165
1.8
25
23.0
7.5
80
170
1.8
25
24.0
8.5
80
170
2.2
25
25.0
8.5
85
180
2.2
25
26.0
9.0
85
180
2.2
32
27.0
9.0
95
190
2.2
32
28.0 10.0
95
190
2.6
32
29.0 10.0
100
195
2.6
32
30.0
11.0
100
195
2.6
32
31.0 11.0
32.0 13.0
105
105
200
200
2.6
2.6
32
32
DRILLING
DC_2 LCF
N160
Stock
Unit : mm
HSS

Structural steel
Aluminium alloy
Work
material

Alloy steel SCM
Cast iron FCD

AISI 430, AISI 405
AISI 420, AISI 440

( 40HRC)
Precipitation
ASTM 630, ASTM 631
Drill Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
2.0
3.0
4.0
5.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
22.0
24.0
26.0
28.0
30.0
32.0
5600
3700
0.07
0.10
4800
3200
0.07
0.10
3200
2100
0.07
0.10
2800
1900
0.04
0.05
2800
0.12
2400
0.12
1600
0.12
1400
0.06
2200
0.14
1900
0.14
1300
0.14
1150
0.07
1850
0.15
1600
0.15
1050
0.15
950
0.08
1400
0.20
1200
0.20
800
0.20
720
0.10
1100
0.23
960
0.23
640
0.21
570
0.11
950
0.26
800
0.26
530
0.24
470
0.12
800
0.27
680
0.27
450
0.25
410
0.13
700
0.28
500
0.28
360
0.26
300
0.14
620
0.29
450
0.29
320
0.27
260
0.15
560
0.30
400
0.30
290
0.27
240
0.15
510
0.32
360
0.32
260
0.29
220
0.16
460
0.33
330
0.33
240
0.30
200
0.16
430
0.35
310
0.35
220
0.31
180
0.17
400
0.36
290
0.36
210
0.33
170
0.18
370
350
0.37
0.38
270
250
0.37
0.38
190
180
0.34
0.35
160
150
0.18
0.19
1) The above cutting conditions are for drilling 3xDC hole depths without a pilot hole. When drilling holes smaller than
1xDC hole depths, it is possible to increase the revolution speed by 20%.
2) Drilling without a pilot hole is recommended. If there is a pilot hole, chips are not broken. Use a pick feed when
chip breaking is necessary.
3) For counter boring of a sloped face, a carbide end mill is recommended.
4) When machining austenitic stainless steels (JIS SUS304, SUS316), set the revolution at 40%-70% and the feed
rate 40%-60%.
6) Please reduce the revolution and feed rate depending on the drilling situation when the installation of workpiece or
machine lacks rigidity.
DRILLING
N161
VIOLET DRILLS
HSS
VSD
Straight shank
P
Steel
HSS
118
110
DC<0.7
0.5 < DC<1 1 < DC < 3
0
0.010
DC>0.7
Thinning
Thinning
DC<2
DC>2
3<DC < 6 6<DC < 10 10<DC < 13
0
0.014
0
0.018
PL
0
0.022
0
0.027
DCON
DC
LF
LCF
OAL
DRILLING
DC
LCF
VSDD0050
VSDD0060
VSDD0070
VSDD0080
VSDD0090
VSDD0100
VSDD0110
VSDD0120
VSDD0130
VSDD0140
VSDD0150
VSDD0160
VSDD0170
VSDD0180
VSDD0190
VSDD0200
VSDD0210
VSDD0220
VSDD0230
VSDD0240
VSDD0250
VSDD0260
VSDD0270
VSDD0280
VSDD0290
VSDD0300
VSDD0310
VSDD0320
VSDD0330
VSDD0340
VSDD0350
VSDD0360
VSDD0370
VSDD0380
VSDD0390
VSDD0400
VSDD0410
VSDD0420
VSDD0430
VSDD0440
0.5
0.6
N162
OAL
LF
PL
DCON
6.18 27.18
7.21 30.21
27
30
0.18
0.21
0.5
0.6
0.7
9.21 32.21
32
0.21
0.7
0.8
10.24 34.24
34
0.24
0.8
0.9
11.27 36.27
36
0.27
0.9
1.0
12.3
40.3
40
0.3
1.0
1.1
14.3
42.3
42
0.3
1.1
1.2
16.4
42.4
42
0.4
1.2
1.3
16.4
45.4
45
0.4
1.3
1.4
18.4
48.4
48
0.4
1.4
1.5
18.5
48.5
48
0.5
1.5
1.6
20.5
50.5
50
0.5
1.6
1.7
20.5
50.5
50
0.5
1.7
1.8
22.5
52.5
52
0.5
1.8
1.9
22.6
52.6
52
0.6
1.9
2.0
23.6
55.6
55
0.6
2.0
2.1
23.6
55.6
55
0.6
2.1
2.2
26.7
58.7
58
0.7
2.2
2.3
26.7
58.7
58
0.7
2.3
2.4
29.7
61.7
61
0.7
2.4
2.5
29.8
61.8
61
0.8
2.5
2.6
29.8
64.8
64
0.8
2.6
2.7
32.8
64.8
64
0.8
2.7
2.8
32.8
67.8
67
0.8
2.8
2.9
32.9
71.9
71
0.9
2.9
3.0
32.9
71.9
71
0.9
3.0
3.1
35.9
71.9
71
0.9
3.1
3.2
36.0
72.0
71
1.0
3.2
3.3
36.0
74.0
73
1.0
3.3
3.4
39.0
74.0
73
1.0
3.4
3.5
39.1
74.1
73
1.1
3.5
3.6
39.1
77.1
76
1.1
3.6
3.7
39.1
77.1
76
1.1
3.7
3.8
43.1
77.1
76
1.1
3.8
3.9
43.2
80.2
79
1.2
3.9
4.0
43.2
84.2
83
1.2
4.0
4.1
43.2
84.2
83
1.2
4.1
4.2
43.3
84.3
83
1.3
4.2
4.3
4.4
47.3
47.3
84.3
87.3
83
86
1.3
1.3
4.3
4.4
Stock
Order Number
Stock
Unit : mm
Order Number
DC
LCF
OAL
LF
PL
DCON
VSDD0450
VSDD0460
VSDD0470
VSDD0480
VSDD0490
VSDD0500
VSDD0510
VSDD0520
VSDD0530
VSDD0540
VSDD0550
VSDD0560
VSDD0570
VSDD0580
VSDD0590
VSDD0600
VSDD0610
VSDD0620
VSDD0630
VSDD0640
VSDD0650
VSDD0660
VSDD0670
VSDD0680
VSDD0690
VSDD0700
VSDD0710
VSDD0720
VSDD0730
VSDD0740
VSDD0750
VSDD0760
VSDD0770
VSDD0780
VSDD0790
VSDD0800
VSDD0810
VSDD0820
VSDD0830
VSDD0840
4.5
4.6
47.4
47.4
87.4
87.4
86
86
1.4
1.4
4.5
4.6
4.7
47.4
90.4
89
1.4
4.7
4.8
52.4
90.4
89
1.4
4.8
4.9
52.5
93.5
92
1.5
4.9
5.0
52.5
93.5
92
1.5
5.0
5.1
52.5
93.5
92
1.5
5.1
5.2
52.6
96.6
95
1.6
5.2
5.3
52.6
96.6
95
1.6
5.3
5.4
57.6
96.6
95
1.6
5.4
5.5
57.7
96.7
95
1.7
5.5
5.6
57.7
99.7
98
1.7
5.6
5.7
57.7
99.7
98
1.7
5.7
5.8
57.7
99.7
98
1.7
5.8
5.9
57.8
99.8
98
1.8
5.9
6.0
57.8 103.8 102
1.8
6.0
6.1
63.8 103.8 102
1.8
6.1
6.2
63.9 103.9 102
1.9
6.2
6.3
63.9 103.9 102
1.9
6.3
6.4
63.9 106.9 105
1.9
6.4
6.5
64.0 107.0 105
2.0
6.5
6.6
64.0 107.0 105
2.0
6.6
6.7
64.0 107.0 105
2.0
6.7
6.8
69.0 107.0 105
2.0
6.8
6.9
69.1 107.1 105
2.1
6.9
7.0
69.1 107.1 105
2.1
7.0
7.1
69.1 110.1 108
2.1
7.1
7.2
69.2 110.2 108
2.2
7.2
7.3
69.2 110.2 108
2.2
7.3
7.4
69.2 113.2 111
2.2
7.4
7.5
69.3 113.3 111
2.3
7.5
7.6
75.3 113.3 111
2.3
7.6
7.7
75.3 116.3 114
2.3
7.7
7.8
75.3 116.3 114
2.3
7.8
7.9
75.4 116.4 114
2.4
7.9
8.0
75.4 116.4 114
2.4
8.0
8.1
75.4 119.4 117
2.4
8.1
8.2
75.5 119.5 117
2.5
8.2
8.3
8.4
75.5 119.5 117

75.5 123.5 121
2.5
2.5
8.3
8.4
HSS
VSDD0850
VSDD0860
VSDD0870
VSDD0880
VSDD0890
VSDD0900
VSDD0910
VSDD0920
VSDD0930
VSDD0940
VSDD0950
VSDD0960
VSDD0970
VSDD0980
VSDD0990
VSDD1000
VSDD1010
VSDD1020
VSDD1030
VSDD1040
VSDD1050
VSDD1060
VSDD1070
DC
LCF
OAL
LF
PL
DCON
8.5
8.6
75.6 123.6 121

81.6 123.6 121
2.6
2.6
8.5
8.6
8.7
81.6 123.6 121
2.6
8.7
8.8
81.6 126.6 124
2.6
8.8
8.9
81.7 126.7 124
2.7
8.9
9.0
81.7 126.7 124
2.7
9.0
9.1
81.7 126.7 124
2.7
9.1
9.2
81.8 129.8 127
2.8
9.2
9.3
81.8 129.8 127
2.8
9.3
9.4
81.8 129.8 127
2.8
9.4
9.5
81.9 129.9 127
2.9
9.5
9.6
87.9 132.9 130
2.9
9.6
9.7
87.9 132.9 130
2.9
9.7
9.8
87.9 132.9 130
2.9
9.8
9.9
88.0 133.0 130
3.0
9.9
10.0
88.0 133.0 130
3.0
10.0
10.1
88.0 136.0 133
3.0
10.1
10.2
88.1 136.1 133
3.1
10.2
10.3
88.1 136.1 133
3.1
10.3
10.4
88.1 136.1 133
3.1
10.4
10.5
88.2 140.2 137
3.2
10.5
10.6
10.7
88.2 140.2 137

95.2 140.2 137
3.2
3.2
10.6
10.7
Order Number
DC
VSDD1080
VSDD1090
VSDD1100
VSDD1110
VSDD1120
VSDD1130
VSDD1140
VSDD1150
VSDD1160
VSDD1170
VSDD1180
VSDD1190
VSDD1200
VSDD1210
VSDD1220
VSDD1230
VSDD1240
VSDD1250
VSDD1260
VSDD1270
VSDD1280
VSDD1290
VSDD1300
LCF
OAL
Stock
Order Number
Stock
Unit : mm
LF
PL
DCON
10.8
10.9
95.2 143.2 140

95.3 143.3 140
3.2
3.3
10.8
10.9
11.0
95.3 143.3 140
3.3
11.0
11.1
95.3 143.3 140
3.3
11.1
11.2
95.4 146.4 143
3.4
11.2
11.3
95.4 146.4 143
3.4
11.3
11.4
95.4 146.4 143
3.4
11.4
11.5
95.5 146.5 143
3.5
11.5
11.6
95.5 149.5 146
3.5
11.6
11.7
95.5 149.5 146
3.5
11.7
11.8
95.5 149.5 146
3.5
11.8
11.9 102.6 149.6 146
3.6
11.9
12.0 102.6 152.6 149
3.6
12.0
12.1 102.6 152.6 149
3.6
12.1
12.2 102.7 152.7 149
3.7
12.2
12.3 102.7 152.7 149
3.7
12.3
12.4 102.7 155.7 152
3.7
12.4
12.5 102.8 155.8 152
3.8
12.5
12.6 102.8 155.8 152
3.8
12.6
12.7 102.8 155.8 152
3.8
12.7
12.8 102.8 155.8 152
3.8
12.8
12.9 102.9 155.9 152

13.0 102.9 155.9 152
3.9
3.9
12.9
13.0
Structural steel
Carbon steel
AISI 1049
Stainless steel
AISI 420
Stainless steel AISI 304

Tool steel AISI D2
Heat-treated steel AISI H13
( 40HRC)
40m/min
30m/min
20m/min
10 14m/min
Work
Material
Cutting
speed
Drill Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
0.5
1.0
1.5
15000
10000
8200
0.01
0.02
0.03
11250
7500
6150
0.01
0.02
0.03
7500
5000
4100
0.01
0.02
0.03
5620
3750
2800
0.01
0.02
0.03
2.0
3.0
4.0
5.0
6.0
6370
4250
3180
2550
2120
0.05
0.10
0.13
0.15
0.18
4780
3180
2390
1910
1590
0.05
0.10
0.13
0.15
0.18
3180
2120
1590
1270
1060
0.05
0.07
0.09
0.11
0.13
2200
1400
1100
860
720
0.04
0.06
0.08
0.10
0.11
7.0
1820
0.20
1360
0.20
910
0.14
610
0.12
8.0
1590
0.22
1190
0.21
800
0.15
540
0.13
9.0
1420
0.24
1060
0.22
710
0.17
480
0.14
10.0
1270
0.26
960
0.23
640
0.18
430
0.15
11.0
1160
0.28
870
0.24
580
0.19
390
0.16
12.0
13.0
1060
980
0.30
0.30
800
730
0.25
0.26
530
490
0.20
0.20
360
330
0.17
0.17
DRILLING
1) Please reduce the revolution depending on drilling situation when the application lacks rigidity.
2) Please use step drilling and reduce the cutting conditions in the case when the drilling depth exceeds 3DC (DC: drill diameter).
3) The above-mentioned cutting condition is standard when using water-soluble cutting fluid.
N163
VIOLET DRILLS
HSS
VTDS
Short, Taper shank
P
Steel
HSS
DC=6
118
Thinning
6<DC < 10 10<DC < 18 18<DC < 30 30<DC < 32
0
0.018
0
0.022
PL
0
0.027
0
0.033
0
0.039
DC
LF
CZC
LCF
OAL
DRILLING
DC LCF OAL LF
PL
CZC
VTDSD0600M1
VTDSD0650M1
VTDSD0660M1
VTDSD0680M1
VTDSD0700M1
VTDSD0720M1
VTDSD0750M1
VTDSD0770M1
VTDSD0780M1
VTDSD0800M1
VTDSD0820M1
VTDSD0850M1
VTDSD0880M1
VTDSD0900M1
VTDSD0950M1
VTDSD0970M1
VTDSD0980M1
VTDSD1000M1
VTDSD1030M1
VTDSD1050M1
VTDSD1080M1
VTDSD1100M1
VTDSD1150M1
VTDSD1200M1
VTDSD1250M2
VTDSD1300M2
VTDSD1350M2
VTDSD1400M2
VTDSD1450M2
VTDSD1500M2
VTDSD1550M2
VTDSD1600M2
VTDSD1650M2
VTDSD1700M2
VTDSD1750M2
VTDSD1800M2
VTDSD1850M2
VTDSD1900M2
VTDSD1950M2
VTDSD2000M2
6.0 45.8 127.8 126

6.5 46.0 128.0 126
1.8
2.0
MT.1
MT.1
6.6 46.0 128.0 126
2.0
MT.1
6.8 46.0 128.0 126
2.0
MT.1
7.0 46.1 128.1 126
2.1
MT.1
7.2 46.2 128.2 126
2.2
MT.1
7.5 46.3 128.3 126
2.3
MT.1
7.7 50.3 132.3 130
2.3
MT.1
7.8 50.3 132.3 130
2.3
MT.1
8.0 50.4 132.4 130
2.4
MT.1
8.2 50.5 132.5 130
2.5
MT.1
8.5 50.6 132.6 130
2.6
MT.1
8.8 54.6 135.6 133
2.6
MT.1
9.0 54.7 135.7 133
2.7
MT.1
9.5 54.9 135.9 133
2.9
MT.1
9.7 58.9 139.9 137
2.9
MT.1
9.8 58.9 139.9 137
2.9
MT.1
10.0 59.0 140.0 137
3.0
MT.1
10.3 59.1 140.1 137
3.1
MT.1
10.5 59.2 140.2 137
3.2
MT.1
10.8 64.2 145.2 142
3.2
MT.1
11.0 64.3 145.3 142
3.3
MT.1
11.5 64.5 145.5 142
3.5
MT.1
12.0 69.6 149.6 146
3.6
MT.1
12.5 69.8 166.8 163
3.8
MT.2
13.0 69.9 166.9 163
3.9
MT.2
13.5 74.1 172.1 168
4.1
MT.2
14.0 74.2 172.2 168
4.2
MT.2
14.5 77.4 175.4 171
4.4
MT.2
15.0 77.5 175.5 171
4.5
MT.2
15.5 81.7 179.7 175
4.7
MT.2
16.0 81.8 179.8 175
4.8
MT.2
16.5 85.0 183.0 178
5.0
MT.2
17.0 85.1 183.1 178
5.1
MT.2
17.5 89.3 187.3 182
5.3
MT.2
18.0 89.4 187.4 182
5.4
MT.2
18.5 91.6 189.6 184
5.6
MT.2
19.0 91.7 189.7 184
5.7
MT.2
19.5 95.9 193.9 188

20.0 96.0 194.0 188
5.9
6.0
MT.2
MT.2
Stock
Order Number
N164
Stock
Unit : mm
Order Number
DC LCF OAL LF
PL
CZC
VTDSD2050M2
VTDSD2100M2
VTDSD2150M2
VTDSD2200M2
VTDSD2250M2
VTDSD2300M2
VTDSD2350M3
VTDSD2400M3
VTDSD2450M3
VTDSD2500M3
VTDSD2550M3
VTDSD2600M3
VTDSD2650M3
VTDSD2700M3
VTDSD2750M3
VTDSD2800M3
VTDSD2850M3
VTDSD2900M3
VTDSD2950M3
VTDSD3000M3
VTDSD3050M3
VTDSD3100M3
VTDSD3150M3
VTDSD3200M3
20.5 99.2 197.2 191

21.0 99.3 197.3 191
6.2
6.3
MT.2
MT.2
21.5 102.5 200.5 194
6.5
MT.2
22.0 102.6 200.6 194
6.6
MT.2
22.5 106.8 204.8 198
6.8
MT.2
23.0 106.9 204.9 198
6.9
MT.2
23.5 109.1 231.1 224
7.1
MT.3
24.0 109.2 231.2 224
7.2
MT.3
24.5 109.4 231.4 224
7.4
MT.3
25.0 109.5 231.5 224
7.5
MT.3
25.5 112.7 233.7 226
7.7
MT.3
26.0 112.8 233.8 226
7.8
MT.3
26.5 113.0 234.0 226
8.0
MT.3
27.0 116.1 238.1 230
8.1
MT.3
27.5 116.3 238.3 230
8.3
MT.3
28.0 116.4 238.4 230
8.4
MT.3
28.5 119.6 240.6 232
8.6
MT.3
29.0 119.7 240.7 232
8.7
MT.3
29.5 119.9 240.9 232
8.9
MT.3
30.0 120.0 241.0 232
9.0
MT.3
30.5 123.2 244.2 235
9.2
MT.3
31.0 123.3 244.3 235
9.3
MT.3
31.5 123.5 244.5 235

32.0 123.6 244.6 235
9.5
9.6
MT.3
MT.3
a
a
HSS

Work
Material
Cutting
speed
Drill Dia.
DC (mm)
Structural steel
Carbon steel
AISI 1049

Copper alloy, Brass

Tool steel AISI D2
Heat-treated steel
AISI H13
(35 40HRC)
33 38m/min
28 33m/min
20m/min
15m/min
18m/min
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
6.0
8.0
2000
1400
0.18
0.22
1750
1270
0.18
0.22
1060
800
0.15
0.20
800
600
0.12
0.15
950
720
0.12
0.15
10.0
1100
0.25
960
0.25
640
0.22
480
0.18
570
0.18
14.0
790
0.30
680
0.28
450
0.25
340
0.23
410
0.23
18.0
20.0
22.0
24.0
28.0
32.0
610
540
480
430
370
320
0.35
0.40
0.42
0.42
0.45
0.45
530
480
430
380
330
280
0.34
0.38
0.40
0.40
0.42
0.42
350
320
290
260
220
200
0.30
0.33
0.35
0.35
0.38
0.38
270
240
220
200
170
150
0.27
0.30
0.30
0.30
0.33
0.33
320
280
260
240
200
180
0.27
0.30
0.30
0.30
0.33
0.33
DRILLING
1) The above-mentioned cutting condition is standard when using water-soluble cutting fluid.
N165
STRAIGHT SHANK DRILLS

HSS
GSD
TiN, Straight shank
P
Steel
HSS
118
110
DC<0.7
0.5 < DC<1 1 < DC < 3
0
0.010
DC>0.7
Thinning
Thinning
DC<2
DC>2
3<DC < 6 6<DC < 10 10<DC < 13
0
0.014
0
0.018
PL
0
0.022
0
0.027
DCON
DC
LF
LCF
OAL
LCF OAL
LF
PL DCON
GSDD0050
GSDD0060
GSDD0070
GSDD0080
GSDD0090
GSDD0100
GSDD0110
GSDD0120
GSDD0130
GSDD0140
GSDD0150
GSDD0160
GSDD0170
GSDD0180
GSDD0190
GSDD0200
GSDD0210
GSDD0220
GSDD0230
GSDD0240
GSDD0250
GSDD0260
GSDD0270
GSDD0280
GSDD0290
GSDD0300
GSDD0310
GSDD0320
GSDD0330
GSDD0340
GSDD0350
GSDD0360
GSDD0370
GSDD0380
GSDD0390
GSDD0400
GSDD0410
GSDD0420
GSDD0430
GSDD0440
0.5
0.6
6.18 27.18
7.21 30.21
27
30
0.18
0.21
0.5
0.6
0.7
9.21 32.21
32
0.21
0.7
0.8
10.24 34.24
34
0.24
0.8
0.9
11.27 36.27
36
0.27
0.9
1.0
12.3 40.3
40
0.3
1.0
1.1
14.3 42.3
42
0.3
1.1
1.2
16.4 42.4
42
0.4
1.2
1.3
16.4 45.4
45
0.4
1.3
1.4
18.4 48.4
48
0.4
1.4
1.5
18.5 48.5
48
0.5
1.5
1.6
20.5 50.5
50
0.5
1.6
1.7
20.5 50.5
50
0.5
1.7
1.8
22.5 52.5
52
0.5
1.8
1.9
22.6 52.6
52
0.6
1.9
2.0
23.6 55.6
55
0.6
2.0
2.1
23.6 55.6
55
0.6
2.1
2.2
26.7 58.7
58
0.7
2.2
2.3
26.7 58.7
58
0.7
2.3
2.4
29.7 61.7
61
0.7
2.4
2.5
29.8 61.8
61
0.8
2.5
2.6
29.8 64.8
64
0.8
2.6
2.7
32.8 64.8
64
0.8
2.7
2.8
32.8 67.8
67
0.8
2.8
2.9
32.9 71.9
71
0.9
2.9
3.0
32.9 71.9
71
0.9
3.0
3.1
35.9 71.9
71
0.9
3.1
3.2
36.0 72.0
71
1.0
3.2
3.3
36.0 74.0
73
1.0
3.3
3.4
39.0 74.0
73
1.0
3.4
3.5
39.1 74.1
73
1.1
3.5
3.6
39.1 77.1
76
1.1
3.6
3.7
39.1 77.1
76
1.1
3.7
3.8
43.1 77.1
76
1.1
3.8
3.9
43.2 80.2
79
1.2
3.9
4.0
43.2 84.2
83
1.2
4.0
4.1
43.2 84.2
83
1.2
4.1
4.2
43.3 84.3
83
1.3
4.2
4.3
4.4
47.3 84.3
47.3 87.3
83
86
1.3
1.3
4.3
4.4
Stock
DC
DRILLING
Order Number
N166
Stock
Unit : mm
Order Number
DC
LCF OAL
GSDD0450
GSDD0460
GSDD0470
GSDD0480
GSDD0490
GSDD0500
GSDD0510
GSDD0520
GSDD0530
GSDD0540
GSDD0550
GSDD0560
GSDD0570
GSDD0580
GSDD0590
GSDD0600
GSDD0610
GSDD0620
GSDD0630
GSDD0640
GSDD0650
GSDD0660
GSDD0670
GSDD0680
GSDD0690
GSDD0700
GSDD0710
GSDD0720
GSDD0730
GSDD0740
GSDD0750
GSDD0760
GSDD0770
GSDD0780
GSDD0790
GSDD0800
GSDD0810
GSDD0820
GSDD0830
GSDD0840
4.5
4.6
47.4
47.4
87.4
87.4
86
86
1.4
1.4
4.5
4.6
4.7
47.4
90.4
89
1.4
4.7
4.8
52.4
90.4
89
1.4
4.8
4.9
52.5
93.5
92
1.5
4.9
5.0
52.5
93.5
92
1.5
5.0
5.1
52.5
93.5
92
1.5
5.1
5.2
52.6
96.6
95
1.6
5.2
5.3
52.6
96.6
95
1.6
5.3
5.4
57.6
96.6
95
1.6
5.4
5.5
57.7
96.7
95
1.7
5.5
5.6
57.7
99.7
98
1.7
5.6
5.7
57.7
99.7
98
1.7
5.7
5.8
57.7
99.7
98
1.7
5.8
5.9
57.8
99.8
98
1.8
5.9
6.0
57.8 103.8
102
1.8
6.0
6.1
63.8 103.8
102
1.8
6.1
6.2
63.9 103.9
102
1.9
6.2
6.3
63.9 103.9
102
1.9
6.3
6.4
63.9 106.9
105
1.9
6.4
6.5
64.0 107.0
105
2.0
6.5
6.6
64.0 107.0
105
2.0
6.6
6.7
64.0 107.0
105
2.0
6.7
6.8
69.0 107.0
105
2.0
6.8
6.9
69.1 107.1
105
2.1
6.9
7.0
69.1 107.1
105
2.1
7.0
7.1
69.1
110.1
108
2.1
7.1
7.2
69.2
110.2
108
2.2
7.2
7.3
69.2
110.2
108
2.2
7.3
7.4
69.2
113.2
111
2.2
7.4
7.5
69.3
113.3
111
2.3
7.5
7.6
75.3
113.3
111
2.3
7.6
7.7
75.3
116.3
114
2.3
7.7
7.8
75.3
116.3
114
2.3
7.8
7.9
75.4
116.4
114
2.4
7.9
8.0
75.4
116.4
114
2.4
8.0
8.1
75.4
119.4
117
2.4
8.1
8.2
75.5
119.5
117
2.5
8.2
8.3
8.4
75.5 119.5
75.5 123.5
117
121
2.5
2.5
8.3
8.4
LF
PL DCON
HSS
Stock
Unit : mm
Order Number
DC
LCF OAL
LF
PL DCON
GSDD0850
GSDD0860
GSDD0870
GSDD0880
GSDD0890
GSDD0900
GSDD0910
GSDD0920
GSDD0930
GSDD0940
GSDD0950
GSDD0960
GSDD0970
GSDD0980
GSDD0990
GSDD1000
GSDD1010
GSDD1020
GSDD1030
GSDD1040
GSDD1050
GSDD1060
GSDD1070
GSDD1080
GSDD1090
GSDD1100
GSDD1110
GSDD1120
GSDD1130
GSDD1140
GSDD1150
GSDD1160
GSDD1170
GSDD1180
GSDD1190
GSDD1200
GSDD1210
GSDD1220
GSDD1230
GSDD1240
GSDD1250
GSDD1260
GSDD1270
GSDD1280
GSDD1290
GSDD1300
8.5
8.6
75.6 123.6
81.6 123.6
121
121
2.6
2.6
8.5
8.6
8.7
81.6 123.6
121
2.6
8.7
8.8
81.6 126.6
124
2.6
8.8
8.9
81.7 126.7
124
2.7
8.9
9.0
81.7 126.7
124
2.7
9.0
9.1
81.7 126.7
124
2.7
9.1
9.2
81.8 129.8
127
2.8
9.2
9.3
81.8 129.8
127
2.8
9.3
9.4
81.8 129.8
127
2.8
9.4
9.5
81.9 129.9
127
2.9
9.5
9.6
87.9 132.9
130
2.9
9.6
9.7
87.9 132.9
130
2.9
9.7
9.8
87.9 132.9
130
2.9
9.8
9.9
88.0 133.0
130
3.0
9.9
10.0
88.0 133.0
130
3.0
10.0
10.1
88.0 136.0
133
3.0
10.1
10.2
88.1 136.1
133
3.1
10.2
10.3
88.1 136.1
133
3.1
10.3
10.4
88.1 136.1
133
3.1
10.4
10.5
88.2 140.2
137
3.2
10.5
10.6
88.2 140.2
137
3.2
10.6
10.7
95.2 140.2
137
3.2
10.7
10.8
95.2 143.2
140
3.2
10.8
10.9
95.3 143.3
140
3.3
10.9
11.0
95.3 143.3
140
3.3
11.0
11.1
95.3 143.3
140
3.3
11.1
11.2
95.4 146.4
143
3.4
11.2
11.3
95.4 146.4
143
3.4
11.3
11.4
95.4 146.4
143
3.4
11.4
11.5
95.5 146.5
143
3.5
11.5
11.6
95.5 149.5
146
3.5
11.6
11.7
95.5 149.5
146
3.5
11.7
11.8
95.6 149.6
146
3.6
11.8
11.9 102.6 149.6
146
3.6
11.9
12.0 102.6 152.6
149
3.6
12.0
12.1 102.6 152.6
149
3.6
12.1
12.2 102.7 152.7
149
3.7
12.2
12.3 102.7 152.7
149
3.7
12.3
12.4 102.7 155.7
152
3.7
12.4
12.5 102.8 155.8
152
3.8
12.5
12.6 102.8 155.8
152
3.8
12.6
12.7 102.8 155.8
152
3.8
12.7
12.8 102.9 155.9
152
3.9
12.8
12.9 102.9 155.9

13.0 102.9 155.9
152
152
3.9
3.9
12.9
13.0
DRILLING
CUTTING CONDITIONS
N198
N167

HSS
SD
Straight shank
P
Steel
118
HSS
0.2 < DC<1 1 < DC < 3
0
0.012
3<DC < 6 6<DC < 10 10<DC < 17.5
0
0.014
0
0.018
PL
0
0.022
0
0.027
DCON
DC
LF
LCF
OAL
a For general drilling.
LCF OAL
LF
PL DCON
SDD0020
SDD0030
SDD0040
SDD0050
SDD0060
SDD0070
SDD0080
SDD0090
SDD0100
SDD0110
SDD0120
SDD0130
SDD0140
SDD0150
SDD0160
SDD0170
SDD0180
SDD0190
SDD0200
SDD0210
SDD0220
SDD0230
SDD0240
SDD0250
SDD0260
SDD0270
SDD0280
SDD0290
SDD0300
SDD0310
SDD0320
SDD0330
SDD0340
SDD0350
SDD0360
SDD0370
SDD0380
SDD0390
SDD0400
SDD0410
0.2
0.3
2.56 19.06
3.09 19.09
19
19
0.06
0.09
0.2
0.3
0.4
5.12 20.12
20
0.12
0.4
0.5
6.15 22.15
22
0.15
0.5
0.6
7.18 24.18
24
0.18
0.6
0.7
10.21 32.21
32
0.21
0.7
0.8
11.24 34.24
34
0.24
0.8
0.9
13.27 36.27
36
0.27
0.9
1.0
18.3
40.3
40
0.3
1.0
1.1
20.3
42.3
42
0.3
1.1
1.2
20.4
42.4
42
0.4
1.2
1.3
22.4
45.4
45
0.4
1.3
1.4
23.4
48.4
48
0.4
1.4
1.5
23.5
48.5
48
0.5
1.5
1.6
25.5
50.5
50
0.5
1.6
1.7
25.5
50.5
50
0.5
1.7
1.8
28.5
52.5
52
0.5
1.8
1.9
28.6
52.6
52
0.6
1.9
2.0
29.6
55.6
55
0.6
2.0
2.1
29.6
55.6
55
0.6
2.1
2.2
33.7
58.7
58
0.7
2.2
2.3
33.7
58.7
58
0.7
2.3
2.4
35.7
61.7
61
0.7
2.4
2.5
35.8
61.8
61
0.8
2.5
2.6
37.8
64.8
64
0.8
2.6
2.7
37.8
64.8
64
0.8
2.7
2.8
39.8
67.8
67
0.8
2.8
2.9
42.9
71.9
71
0.9
2.9
3.0
42.9
71.9
71
0.9
3.0
3.1
42.9
71.9
71
0.9
3.1
3.2
43.0
72.0
71
1.0
3.2
3.3
46.0
74.0
73
1.0
3.3
3.4
46.0
74.0
73
1.0
3.4
3.5
46.1
74.1
73
1.1
3.5
3.6
49.1
77.1
76
1.1
3.6
3.7
49.1
77.1
76
1.1
3.7
3.8
49.1
77.1
76
1.1
3.8
3.9
52.2
80.2
79
1.2
3.9
4.0
4.1
55.2
55.2
84.2
84.2
83
83
1.2
1.2
4.0
4.1
Stock
DC
DRILLING
Order Number
N168
Stock
Unit : mm
Order Number
DC
LCF OAL
SDD0420
SDD0430
SDD0440
SDD0450
SDD0460
SDD0470
SDD0480
SDD0490
SDD0500
SDD0510
SDD0520
SDD0530
SDD0540
SDD0550
SDD0560
SDD0570
SDD0580
SDD0590
SDD0600
SDD0610
SDD0620
SDD0630
SDD0640
SDD0650
SDD0660
SDD0670
SDD0680
SDD0690
SDD0700
SDD0710
SDD0720
SDD0730
SDD0740
SDD0750
SDD0760
SDD0770
SDD0780
SDD0790
SDD0800
SDD0810
4.2
4.3
55.3
55.3
84.3
84.3
83
83
1.3
1.3
4.2
4.3
4.4
57.3
87.3
86
1.3
4.4
4.5
57.4
87.4
86
1.4
4.5
4.6
57.4
87.4
86
1.4
4.6
4.7
60.4
90.4
89
1.4
4.7
4.8
60.4
90.4
89
1.4
4.8
4.9
63.5
93.5
92
1.5
4.9
5.0
63.5
93.5
92
1.5
5.0
5.1
63.5
93.5
92
1.5
5.1
5.2
65.6
96.6
95
1.6
5.2
5.3
65.6
96.6
95
1.6
5.3
5.4
65.6
96.6
95
1.6
5.4
5.5
65.7
96.7
95
1.7
5.5
5.6
68.7
99.7
98
1.7
5.6
5.7
68.7
99.7
98
1.7
5.7
5.8
68.7
99.7
98
1.7
5.8
5.9
68.8
99.8
98
1.8
5.9
6.0
71.8 103.8
102
1.8
6.0
6.1
71.8 103.8
102
1.8
6.1
6.2
71.9 103.9
102
1.9
6.2
6.3
71.9 103.9
102
1.9
6.3
6.4
74.9 106.9
105
1.9
6.4
6.5
75.0 107.0
105
2.0
6.5
6.6
75.0 107.0
105
2.0
6.6
6.7
75.0 107.0
105
2.0
6.7
6.8
75.0 107.0
105
2.0
6.8
6.9
75.1 107.1
105
2.1
6.9
7.0
75.1 107.1
105
2.1
7.0
7.1
77.1
110.1
108
2.1
7.1
7.2
77.2
110.2
108
2.2
7.2
7.3
77.2
110.2
108
2.2
7.3
7.4
80.2
113.2
111
2.2
7.4
7.5
80.3
113.3
111
2.3
7.5
7.6
80.3
113.3
111
2.3
7.6
7.7
83.3
116.3
114
2.3
7.7
7.8
83.3
116.3
114
2.3
7.8
7.9
83.4
116.4
114
2.4
7.9
8.0
8.1
83.4
86.4
116.4
119.4
114
117
2.4
2.4
8.0
8.1
LF
PL DCON
HSS
DC
LCF OAL
LF
PL DCON
SDD0820
SDD0830
SDD0840
SDD0850
SDD0860
SDD0870
SDD0880
SDD0890
SDD0900
SDD0910
SDD0920
SDD0930
SDD0940
SDD0950
SDD0960
SDD0970
SDD0980
SDD0990
SDD1000
SDD1010
SDD1020
SDD1030
SDD1040
SDD1050
SDD1060
SDD1070
SDD1080
SDD1090
SDD1100
SDD1110
SDD1120
SDD1130
SDD1140
SDD1150
SDD1160
SDD1170
SDD1180
SDD1190
SDD1200
SDD1210
SDD1220
SDD1230
SDD1240
SDD1250
SDD1260
SDD1270
SDD1280
SDD1290
SDD1300
SDD1350
8.2
8.3
86.5 119.5
86.5 119.5
117
117
2.5
2.5
8.2
8.3
8.4
89.5 123.5
121
2.5
8.4
8.5
89.6 123.6
121
2.6
8.5
8.6
89.6 123.6
121
2.6
8.6
8.7
89.6 123.6
121
2.6
8.7
8.8
91.6 126.6
124
2.6
8.8
8.9
91.7 126.7
124
2.7
8.9
9.0
91.7 126.7
124
2.7
9.0
9.1
91.7 126.7
124
2.7
9.1
9.2
94.8 129.8
127
2.8
9.2
9.3
94.8 129.8
127
2.8
9.3
9.4
94.8 129.8
127
2.8
9.4
9.5
94.9 129.9
127
2.9
9.5
9.6
97.9 132.9
130
2.9
9.6
9.7
97.9 132.9
130
2.9
9.7
9.8
97.9 132.9
130
2.9
9.8
9.9
98.0 133.0
130
3.0
9.9
10.0
98.0 133.0
130
3.0
10.0
10.1
101.0 136.0
133
3.0
10.1
10.2
101.1 136.1
133
3.1
10.2
10.3
101.1 136.1
133
3.1
10.3
10.4
101.1 136.1
133
3.1
10.4
10.5
103.2 140.2
137
3.2
10.5
10.6
103.2 140.2
137
3.2
10.6
10.7
103.2 140.2
137
3.2
10.7
10.8
106.2 143.2
140
3.2
10.8
10.9
106.3 143.3
140
3.3
10.9
11.0
106.3 143.3
140
3.3
11.0
11.1
106.3 143.3
140
3.3
11.1
11.2
109.4 146.4
143
3.4
11.2
11.3
109.4 146.4
143
3.4
11.3
11.4
109.4 146.4
143
3.4
11.4
11.5
109.5 146.5
143
3.5
11.5
11.6
112.5 149.5
146
3.5
11.6
11.7
112.5 149.5
146
3.5
11.7
11.8
112.6 149.6
146
3.6
11.8
11.9
112.6 149.6
146
3.6
11.9
12.0
114.6 152.6
149
3.6
12.0
12.1
114.6 152.6
149
3.6
12.1
12.2
114.7 152.7
149
3.7
12.2
12.3
114.7 152.7
149
3.7
12.3
12.4
117.7 155.7
152
3.7
12.4
12.5
117.8 155.8
152
3.8
12.5
12.6
117.8 155.8
152
3.8
12.6
12.7
117.8 155.8
152
3.8
12.7
12.8
117.9 155.9
152
3.9
12.8
12.9
117.9 155.9
152
3.9
12.9
13.0
13.5
117.9 155.9
126.1 172.1
152
168
3.9
4.1
13.0
13.5
Order Number
SDD1400
SDD1450
SDD1500
SDD1550
SDD1600
SDD1650
SDD1700
SDD1750
DC
LCF OAL
LF
PL DCON
14.0 126.2 172.2

14.5 126.4 172.4
168
168
4.2
4.4
14.0
14.5
15.0 136.5 185.5
181
4.5
15.0
15.5 136.7 185.7
181
4.7
15.5
16.0 136.8 185.8
181
4.8
16.0
16.5 137.0 186.0
181
5.0
16.5
17.0 148.1 199.1

17.5 148.3 199.3
194
194
5.1
5.3
17.0
17.5
DRILLING
Order Number
Stock
Stock
Unit : mm
CUTTING CONDITIONS
N199
N169

HSS
SD
Straight shank, 1/100mm
P
Steel
118
HSS
0.25 < DC < 5.95
0
0.007

PL
DCON
DC
LF
LCF
OAL
a The diameter tolerance is 0.007 mm.
LCF OAL
LF
PL DCON
SDD0025
SDD0035
SDD0045
SDD0055
SDD0065
SDD0075
SDD0085
SDD0095
SDD0105
SDD0115
SDD0125
SDD0135
SDD0145
SDD0155
SDD0165
SDD0175
SDD0185
SDD0195
SDD0205
SDD0215
SDD0225
SDD0235
SDD0245
SDD0255
SDD0265
SDD0275
SDD0285
SDD0295
SDD0305
SDD0315
SDD0325
SDD0335
SDD0345
SDD0355
SDD0365
SDD0375
SDD0385
SDD0395
SDD0405
SDD0415
0.25
0.35
3.08 19.08
4.11 19.11
19
19
0.08
0.11
0.25
0.35
0.45
5.14 20.14
20
0.14
0.45
0.55
7.17 24.17
24
0.17
0.55
0.65
8.20 26.20
26
0.20
0.65
0.75
11.23 34.23
34
0.23
0.75
0.85 13.26 36.26
36
0.26
0.85
0.95 18.29 40.29
40
0.29
0.95
1.05 20.3
42.3
42
0.3
1.05
1.15 20.4
42.4
42
0.4
1.15
1.25 22.4
45.4
45
0.4
1.25
1.35 23.4
48.4
48
0.4
1.35
1.45 23.4
48.4
48
0.4
1.45
1.55 25.5
50.5
50
0.5
1.55
1.65 25.5
50.5
50
0.5
1.65
1.75 28.5
52.5
52
0.5
1.75
1.85 28.6
52.6
52
0.6
1.85
1.95 29.6
55.6
55
0.6
1.95
2.05 29.6
55.6
55
0.6
2.05
2.15 29.7
55.7
55
0.7
2.15
2.25 33.7
58.7
58
0.7
2.25
2.35 33.7
58.7
58
0.7
2.35
2.45 35.7
61.7
61
0.7
2.45
2.55 37.8
64.8
64
0.8
2.55
2.65 37.8
64.8
64
0.8
2.65
2.75 39.8
67.8
67
0.8
2.75
2.85 39.9
67.9
67
0.9
2.85
2.95 42.9
71.9
71
0.9
2.95
3.05 42.9
71.9
71
0.9
3.05
3.15 43.0
72.0
71
1.0
3.15
3.25 43.0
72.0
71
1.0
3.25
3.35 46.0
74.0
73
1.0
3.35
3.45 46.0
74.0
73
1.0
3.45
3.55 46.1
74.1
73
1.1
3.55
3.65 49.1
77.1
76
1.1
3.65
3.75 49.1
77.1
76
1.1
3.75
3.85 52.2
80.2
79
1.2
3.85
3.95 52.2
80.2
79
1.2
3.95
4.05 55.2
4.15 55.3
84.2
84.3
83
83
1.2
1.3
4.05
4.15
Stock
DC
DRILLING
Order Number
N170
Stock
Unit : mm
Order Number
DC
LCF OAL
LF
PL DCON
SDD0425
SDD0435
SDD0445
SDD0455
SDD0465
SDD0475
SDD0485
SDD0495
SDD0505
SDD0515
SDD0525
SDD0535
SDD0545
SDD0555
SDD0565
SDD0575
SDD0585
SDD0595
4.25
4.35
55.3
55.3
84.3
84.3
83
83
1.3
1.3
4.25
4.35
4.45
57.3
87.3
86
1.3
4.45
4.55
57.4
87.4
86
1.4
4.55
4.65
60.4
90.4
89
1.4
4.65
4.75
60.4
90.4
89
1.4
4.75
4.85
60.5
90.5
89
1.5
4.85
4.95
63.5
93.5
92
1.5
4.95
5.05
63.5
93.5
92
1.5
5.05
5.15
63.6
93.6
92
1.6
5.15
5.25
65.6
96.6
95
1.6
5.25
5.35
65.6
96.6
95
1.6
5.35
5.45
65.6
96.6
95
1.6
5.45
5.55
65.7
96.7
95
1.7
5.55
5.65
68.7
99.7
98
1.7
5.65
5.75
68.7
99.7
98
1.7
5.75
5.85
5.95
68.8
68.8
99.8
99.8
98
98
1.8
1.8
5.85
5.95

CUTTING CONDITIONS
N199
SDLS
Long shank straight drill
NEW
P
Steel
118
HSS
Thinning
HSS
DC>2
1 < DC < 3
3<DC < 6 6<DC < 10
0
0.014

PL
0
0.018
0
0.022
DCON
DC
LF
LCF
OAL
a It is recommended to use when long overall length is demanded for preventing collision with workpiece with high rigidity.
a For both machining center and manually operated machines.
DC
LCF OAL
LF
PL DCON
SDLSD0100A100
SDLSD0110A100
SDLSD0120A100
SDLSD0130A100
SDLSD0140A100
SDLSD0150A100
SDLSD0160A100
SDLSD0170A100
SDLSD0180A100
SDLSD0190A100
SDLSD0200A100
SDLSD0210A150
SDLSD0220A150
SDLSD0230A150
SDLSD0240A150
SDLSD0250A150
SDLSD0260A150
SDLSD0270A150
SDLSD0280A150
SDLSD0290A150
SDLSD0300A150
SDLSD0310A150
SDLSD0320A150
SDLSD0330A150
SDLSD0340A150
SDLSD0350A150
SDLSD0360A200
SDLSD0370A200
SDLSD0380A200
SDLSD0390A200
SDLSD0400A200
SDLSD0410A200
SDLSD0420A200
SDLSD0430A200
SDLSD0440A200
SDLSD0450A200
SDLSD0460A200
SDLSD0470A200
SDLSD0480A200
SDLSD0490A200
1.0
1.1
12.3 100.3
14.3 100.3
100
100
0.3
0.3
1.0
1.1
1.2
16.4 100.4
100
0.4
1.2
1.3
16.4 100.4
100
0.4
1.3
1.4
18.4 100.4
100
0.4
1.4
1.5
18.5 100.5
100
0.5
1.5
1.6
20.5 100.5
100
0.5
1.6
1.7
20.5 100.5
100
0.5
1.7
1.8
22.5 100.5
100
0.5
1.8
1.9
22.6 100.6
100
0.6
1.9
2.0
23.6 100.6
100
0.6
2.0
2.1
23.6 150.6
150
0.6
2.1
2.2
26.7 150.7
150
0.7
2.2
2.3
26.7 150.7
150
0.7
2.3
2.4
29.7 150.7
150
0.7
2.4
2.5
29.8 150.8
150
0.8
2.5
2.6
29.8 150.8
150
0.8
2.6
2.7
32.8 150.8
150
0.8
2.7
2.8
32.8 150.8
150
0.8
2.8
2.9
32.9 150.9
150
0.9
2.9
3.0
32.9 150.9
150
0.9
3.0
3.1
35.9 150.9
150
0.9
3.1
3.2
36.0 151.0
150
1.0
3.2
3.3
36.0 151.0
150
1.0
3.3
3.4
39.0 151.0
150
1.0
3.4
3.5
39.1 151.1
150
1.1
3.5
3.6
39.1 201.1
200
1.1
3.6
3.7
39.1 201.1
200
1.1
3.7
3.8
43.1 201.1
200
1.1
3.8
3.9
43.2 201.2
200
1.2
3.9
4.0
43.2 201.2
200
1.2
4.0
4.1
43.2 201.2
200
1.2
4.1
4.2
43.3 201.3
200
1.3
4.2
4.3
47.3 201.3
200
1.3
4.3
4.4
47.3 201.3
200
1.3
4.4
4.5
47.4 201.4
200
1.4
4.5
4.6
47.4 201.4
200
1.4
4.6
4.7
47.4 201.4
200
1.4
4.7
4.8
4.9
52.4 201.4
52.5 201.5
200
200
1.4
1.5
4.8
4.9
Order Number
DC
LCF OAL
LF
PL DCON
SDLSD0500A200
SDLSD0510A200
SDLSD0520A200
SDLSD0530A200
SDLSD0540A200
SDLSD0550A200
SDLSD0560A200
SDLSD0570A200
SDLSD0580A200
SDLSD0590A200
SDLSD0600A200
SDLSD0610A250
SDLSD0620A250
SDLSD0630A250
SDLSD0640A250
SDLSD0650A250
SDLSD0660A250
SDLSD0670A250
SDLSD0680A250
SDLSD0690A250
SDLSD0700A250
SDLSD0710A250
SDLSD0720A250
SDLSD0730A250
SDLSD0740A250
SDLSD0750A250
SDLSD0760A250
SDLSD0770A250
SDLSD0780A250
SDLSD0790A250
SDLSD0800A250
SDLSD0810A250
SDLSD0820A250
SDLSD0830A250
SDLSD0840A250
SDLSD0850A250
SDLSD0860A250
SDLSD0870A250
SDLSD0880A250
SDLSD0890A250
5.0
5.1
52.5 201.5
52.5 201.5
200
200
1.5
1.5
5.0
5.1
5.2
52.6 201.6
200
1.6
5.2
5.3
52.6 201.6
200
1.6
5.3
5.4
57.6 201.6
200
1.6
5.4
5.5
57.7 201.7
200
1.7
5.5
5.6
57.7 201.7
200
1.7
5.6
5.7
57.7 201.7
200
1.7
5.7
5.8
57.7 201.7
200
1.7
5.8
5.9
57.8 201.8
200
1.8
5.9
6.0
57.8 201.8
200
1.8
6.0
6.1
63.8 251.8
250
1.8
6.1
6.2
63.9 251.9
250
1.9
6.2
6.3
63.9 251.9
250
1.9
6.3
6.4
63.9 251.9
250
1.9
6.4
6.5
64.0 252.0
250
2.0
6.5
6.6
64.0 252.0
250
2.0
6.6
6.7
64.0 252.0
250
2.0
6.7
6.8
69.0 252.0
250
2.0
6.8
6.9
69.1 252.1
250
2.1
6.9
7.0
69.1 252.1
250
2.1
7.0
7.1
69.1 252.1
250
2.1
7.1
7.2
69.2 252.2
250
2.2
7.2
7.3
69.2 252.2
250
2.2
7.3
7.4
69.2 252.2
250
2.2
7.4
7.5
69.3 252.3
250
2.3
7.5
7.6
75.3 252.3
250
2.3
7.6
7.7
75.3 252.3
250
2.3
7.7
7.8
75.3 252.3
250
2.3
7.8
7.9
75.4 252.4
250
2.4
7.9
8.0
75.4 252.4
250
2.4
8.0
8.1
75.4 252.4
250
2.4
8.1
8.2
75.5 252.5
250
2.5
8.2
8.3
75.5 252.5
250
2.5
8.3
8.4
75.5 252.5
250
2.5
8.4
8.5
75.6 252.6
250
2.6
8.5
8.6
81.6 252.6
250
2.6
8.6
8.7
81.6 252.6
250
2.6
8.7
8.8
8.9
81.6 252.6
81.7 252.7
250
250
2.6
2.7
8.8
8.9
CUTTING CONDITIONS
DRILLING
Order Number
Stock
Stock
Unit : mm
N173
N171

HSS
SDLS
Long shank straight drill
NEW
DC
LCF OAL
LF
PL DCON
SDLSD0900A250
SDLSD0910A250
SDLSD0920A250
SDLSD0930A250
SDLSD0940A250
SDLSD0950A250
SDLSD0960A250
SDLSD0970A250
SDLSD0980A250
SDLSD0990A250
SDLSD1000A250
9.0
9.1
81.7 252.7
81.7 252.7
250
250
2.7
2.7
9.0
9.1
9.2
81.8 252.8
250
2.8
9.2
9.3
81.8 252.8
250
2.8
9.3
9.4
81.8 252.8
250
2.8
9.4
9.5
81.9 252.9
250
2.9
9.5
9.6
87.9 252.9
250
2.9
9.6
9.7
87.9 252.9
250
2.9
9.7
9.8
87.9 252.9
250
2.9
9.8
9.9
10.0
88.0 253.0
88.0 253.0
250
250
3.0
3.0
9.9
10.0
DRILLING
Order Number
N172
Stock
Unit : mm
HSS

Mild Steel ( < 180HB),
Work Carbon Steel, Alloy Steel(180 250HB)
material
ASTM A36, AISI 1010
Alloy tool steel ( < 30HRC)
Alloy tool steel (<40HRC)
AISI H13, AISI L6 etc
AISI H13, AISI L6 etc
No 45 B etc
Cutting speed Revolution Feed rate Table Feed Cutting speed Revolution Feed rate Table Feed Cutting speed Revolution Feed rate Table Feed Cutting speed Revolution Feed rate Table Feed
Dia.
DC (mm) (m/min) (min-1) (mm/rev) (mm/min) (m/min) (min-1) (mm/rev) (mm/min) (m/min) (min-1) (mm/rev) (mm/min) (m/min) (min-1) (mm/rev) (mm/min)
1.0
1.5
16
20
5000
4200
0.02
0.03
100
125
13
15
4000
3200
0.01
0.02
2.0
20
3200
0.05
160
16
2500
3.0
20
2100
0.1
210
17
1800
4.0
5.0
6.0
7.0
8.0
9.0
10.0
20
20
20
20
20
20
20
1600
1300
1050
900
800
700
650
0.12
0.14
0.17
0.19
0.2
0.21
0.22
190
180
175
170
160
145
140
17
17
17
17
17
17
17
1350
1100
900
780
670
600
540
40
60
9
10
2800
2100
0.007
0.01
15
20
16
20
5000
4200
0.02
0.03
100
125
0.03
75
11
1800
0.02
35
20
3200
0.05
160
0.06
105
11
1200
0.04
45
22
2300
0.1
230
0.08
0.1
0.12
0.14
0.15
0.16
0.17
105
110
105
105
100
95
90
11
11
11
11
11
11
11
900
700
600
500
450
400
350
0.06
0.08
0.1
0.11
0.12
0.13
0.14
50
55
60
55
50
50
45
22
22
22
22
22
22
22
1750
1400
1150
1000
890
780
700
0.12
0.14
0.18
0.19
0.2
0.21
0.22
210
195
205
190
175
160
150
Austenitic Stainless Steel ( < 200HB) Copper, Copper alloy
Ferritic, Precipitation hardening

Work stainless steel ( < 200HB)
material
Cutting speed Revolution Feed rate Table Feed Cutting speed Revolution Feed rate Table Feed Cutting speed Revolution Feed rate Table Feed Cutting speed Revolution Feed rate Table Feed
Dia.
DC (mm) (m/min) (min-1) (mm/rev) (mm/min) (m/min) (min-1) (mm/rev) (mm/min) (m/min) (min-1) (mm/rev) (mm/min) (m/min) (min-1) (mm/rev) (mm/min)
1.0
1.5
13
14
4000
3000
0.02
0.03
80
90
9
9
3000
2000
0.02
0.03
60
60
16
20
5000
4200
0.02
0.03
100
125
22
28
7000
6000
0.04
0.06
280
360
2.0
3.0
4.0
5.0
6.0
7.0
8.0
14
15
15
15
15
15
15
2200
1600
1200
950
800
700
600
0.05
0.07
0.11
0.13
0.14
0.15
0.16
110
110
130
120
110
105
95
9
9
9
9
10
10
10
1500
1000
700
600
530
450
400
0.04
0.06
0.08
0.09
0.1
0.11
0.13
60
60
55
50
50
45
50
20
20
20
20
20
20
20
3200
2100
1600
1300
1050
900
800
0.05
0.1
0.12
0.14
0.18
0.19
0.2
160
210
190
180
185
170
160
30
40
40
40
40
40
40
4800
4200
3200
2550
2100
1800
1600
0.08
0.13
0.16
0.2
0.23
0.25
0.28
380
545
510
510
480
450
445
9.0
10.0
15
15
520
480
0.17
0.18
85
85
10
10
360
310
0.14
0.15
50
45
20
20
700
650
0.21
0.22
145
140
40
40
1400
1280
0.3
0.33
420
420
Lower the revolution and feedrate accordingly, when the work material is not rigid or there are restrictions on the machine.
When drilling holes greater than 3 x drill diameter hole depths, please use a peck feed.
The cutting conditions mentioned above arevstandard with the tool protrusion length was made 2 times the flute length.
Use of water-soluble cutting fluid is recommended. Please reduce the revolution when using water-insoluble cutting fluid.
Use sufficient cutting fluid. Please reduce the revolution when insufficient cutting fluid.
When using a guide bush, please confirm the flute length > A. In case of short flute length, please conduct machining without the bush.
And, when not being able to dismount the bush, please use LSD or GWSL.
1.0-1.5 times the drill diameter
Guide bushing
Work Material
1)
2)
3)
4)
5)
6)
DRILLING
(Note) The intermediate diameter revolution is not tabulated. It is matched to the large diameter side and closest drill diameter conditions or
by calculating the cutting speed of the closest drill diameter. Set the feedrate per revolution to a suitable value with the recommended
feedrate of the closest drill diameter as the standard.
Distance from end of bushing to

bottom of work
Through hole allowance
N173
HSS
KSD
Cobalt HSS, For stainless steel
P
Steel
Stainless Steel
118
125
CO HSS
Thinning
DC<2
Non-ferrous Metal
DC>2
DC>2
1 < DC < 3
3<DC < 6
6<DC < 10
10<DC < 13
0
0.014
0
0.018
0
0.022
0
0.027
PL
DCON
DC
LF
LCF
OAL
a Sharp edge geometry for stainless steels up to 200HB.
LCF OAL
LF
PL DCON
KSDD0100
KSDD0110
KSDD0120
KSDD0130
KSDD0140
KSDD0150
KSDD0160
KSDD0170
KSDD0180
KSDD0190
KSDD0200
KSDD0210
KSDD0220
KSDD0230
KSDD0240
KSDD0250
KSDD0260
KSDD0270
KSDD0280
KSDD0290
KSDD0300
KSDD0310
KSDD0320
KSDD0330
KSDD0340
KSDD0350
KSDD0360
KSDD0370
KSDD0380
KSDD0390
KSDD0400
KSDD0410
KSDD0420
KSDD0430
KSDD0440
KSDD0450
KSDD0460
KSDD0470
KSDD0480
KSDD0490
1.0
1.1
12.3
14.3
40.3
42.3
40
42
0.3
0.3
1.0
1.1
1.2
16.3
42.3
42
0.3
1.2
1.3
16.3
45.3
45
0.3
1.3
1.4
18.4
48.4
48
0.4
1.4
1.5
18.4
48.4
48
0.4
1.5
1.6
20.4
50.4
50
0.4
1.6
1.7
20.4
50.4
50
0.4
1.7
1.8
22.5
52.5
52
0.5
1.8
1.9
22.5
52.5
52
0.5
1.9
2.0
29.6
55.6
55
0.6
2.0
2.1
29.6
55.6
55
0.6
2.1
2.2
33.7
58.7
58
0.7
2.2
2.3
33.7
58.7
58
0.7
2.3
2.4
35.7
61.7
61
0.7
2.4
2.5
35.8
61.8
61
0.8
2.5
2.6
37.8
64.8
64
0.8
2.6
2.7
37.8
64.8
64
0.8
2.7
2.8
39.8
67.8
67
0.8
2.8
2.9
42.9
71.9
71
0.9
2.9
3.0
42.9
71.9
71
0.9
3.0
3.1
42.9
71.9
71
0.9
3.1
3.2
43.0
72.0
71
1.0
3.2
3.3
46.0
74.0
73
1.0
3.3
3.4
46.0
74.0
73
1.0
3.4
3.5
46.1
74.1
73
1.1
3.5
3.6
49.1
77.1
76
1.1
3.6
3.7
49.1
77.1
76
1.1
3.7
3.8
49.1
77.1
76
1.1
3.8
3.9
52.2
80.2
79
1.2
3.9
4.0
55.2
84.2
83
1.2
4.0
4.1
55.2
84.2
83
1.2
4.1
4.2
55.3
84.3
83
1.3
4.2
4.3
55.3
84.3
83
1.3
4.3
4.4
57.3
87.3
86
1.3
4.4
4.5
57.4
87.4
86
1.4
4.5
4.6
57.4
87.4
86
1.4
4.6
4.7
60.4
90.4
89
1.4
4.7
4.8
4.9
60.4
63.5
90.4
93.5
89
92
1.4
1.5
4.8
4.9
Stock
DC
DRILLING
Order Number
N174
Stock
Unit : mm
Order Number
DC
LCF OAL
KSDD0500
KSDD0510
KSDD0520
KSDD0530
KSDD0540
KSDD0550
KSDD0560
KSDD0570
KSDD0580
KSDD0590
KSDD0600
KSDD0610
KSDD0620
KSDD0630
KSDD0640
KSDD0650
KSDD0660
KSDD0670
KSDD0680
KSDD0690
KSDD0700
KSDD0710
KSDD0720
KSDD0730
KSDD0740
KSDD0750
KSDD0760
KSDD0770
KSDD0780
KSDD0790
KSDD0800
KSDD0810
KSDD0820
KSDD0830
KSDD0840
KSDD0850
KSDD0860
KSDD0870
KSDD0880
KSDD0890
5.0
5.1
63.5
63.5
93.5
93.5
92
92
1.5
1.5
5.0
5.1
5.2
65.6
96.6
95
1.6
5.2
5.3
65.6
96.6
95
1.6
5.3
5.4
65.6
96.6
95
1.6
5.4
5.5
65.7
96.7
95
1.7
5.5
5.6
68.7
99.7
98
1.7
5.6
5.7
68.7
99.7
98
1.7
5.7
5.8
68.7
99.7
98
1.7
5.8
5.9
68.8
99.8
98
1.8
5.9
6.0
71.8
103.8
102
1.8
6.0
6.1
71.8
103.8
102
1.8
6.1
6.2
71.9
103.9
102
1.9
6.2
6.3
71.9
103.9
102
1.9
6.3
6.4
74.9
106.9
105
1.9
6.4
6.5
75.0
107.0
105
2.0
6.5
6.6
75.0
107.0
105
2.0
6.6
6.7
75.0
107.0
105
2.0
6.7
6.8
75.0
107.0
105
2.0
6.8
6.9
75.1
107.1
105
2.1
6.9
7.0
75.1
107.1
105
2.1
7.0
7.1
77.1
110.1
108
2.1
7.1
7.2
77.2
110.2
108
2.2
7.2
7.3
77.2
110.2
108
2.2
7.3
7.4
80.2
113.2
111
2.2
7.4
7.5
80.3
113.3
111
2.3
7.5
7.6
80.3
113.3
111
2.3
7.6
7.7
83.3
116.3
114
2.3
7.7
7.8
83.3
116.3
114
2.3
7.8
7.9
83.4
116.4
114
2.4
7.9
8.0
83.4
116.4
114
2.4
8.0
8.1
86.4
119.4
117
2.4
8.1
8.2
86.5
119.5
117
2.5
8.2
8.3
86.5
119.5
117
2.5
8.3
8.4
89.5
123.5
121
2.5
8.4
8.5
89.6
123.6
121
2.6
8.5
8.6
89.6
123.6
121
2.6
8.6
8.7
89.6
123.6
121
2.6
8.7
8.8
8.9
91.6
91.7
126.6
126.7
124
124
2.6
2.7
8.8
8.9
LF
PL DCON
HSS
Stock
Unit : mm
Order Number
DC
LCF OAL
LF
PL DCON
KSDD0900
KSDD0910
KSDD0920
KSDD0930
KSDD0940
KSDD0950
KSDD0960
KSDD0970
KSDD0980
KSDD0990
KSDD1000
KSDD1010
KSDD1020
KSDD1030
KSDD1040
KSDD1050
KSDD1060
KSDD1070
KSDD1080
KSDD1090
KSDD1100
KSDD1110
KSDD1120
KSDD1130
KSDD1140
KSDD1150
KSDD1160
KSDD1170
KSDD1180
KSDD1190
KSDD1200
KSDD1210
KSDD1220
KSDD1230
KSDD1240
KSDD1250
KSDD1260
KSDD1270
KSDD1280
KSDD1290
KSDD1300
9.0
9.1
91.7 126.7
91.7 126.7
124
124
2.7
2.7
9.0
9.1
9.2
94.8 129.8
127
2.8
9.2
9.3
94.8 129.8
127
2.8
9.3
9.4
94.8 129.8
127
2.8
9.4
9.5
94.9 129.9
127
2.9
9.5
9.6
97.9 132.9
130
2.9
9.6
9.7
97.9 132.9
130
2.9
9.7
9.8
97.9 132.9
130
2.9
9.8
9.9
98.0 133.0
130
3.0
9.9
10.0
98.0 133.0
130
3.0
10.0
10.1
101.0 136.0
133
3.0
10.1
10.2
101.1 136.1
133
3.1
10.2
10.3
101.1 136.1
133
3.1
10.3
10.4
101.1 136.1
133
3.1
10.4
10.5
103.2 140.2
137
3.2
10.5
10.6
103.2 140.2
137
3.2
10.6
10.7
103.2 140.2
137
3.2
10.7
10.8
106.2 143.2
140
3.2
10.8
10.9
106.3 143.3
140
3.3
10.9
11.0
106.3 143.3
140
3.3
11.0
11.1
106.3 143.3
140
3.3
11.1
11.2
109.4 146.4
143
3.4
11.2
11.3
109.4 146.4
143
3.4
11.3
11.4
109.4 146.4
143
3.4
11.4
11.5
109.5 146.5
143
3.5
11.5
11.6
112.5 149.5
146
3.5
11.6
11.7
112.5 149.5
146
3.5
11.7
11.8
112.5 149.5
146
3.5
11.8
11.9
112.6 149.6
146
3.6
11.9
12.0
114.6 152.6
149
3.6
12.0
12.1
114.6 152.6
149
3.6
12.1
12.2
114.7 152.7
149
3.7
12.2
12.3
114.7 152.7
149
3.7
12.3
12.4
117.7 155.7
152
3.7
12.4
12.5
117.8 155.8
152
3.8
12.5
12.6
117.8 155.8
152
3.8
12.6
12.7
117.8 155.8
152
3.8
12.7
12.8
117.8 155.8
152
3.8
12.8
12.9
13.0
117.9 155.9
117.9 155.9
152
152
3.9
3.9
12.9
13.0
DRILLING
CUTTING CONDITIONS
N199
N175

HSS
GWSS
TiN, For deep hole, Convolute flute
P
Steel
CO HSS
118
Thinning
1 < DC < 3
3<DC < 6
6<DC < 10
10<DC < 13
0
0.014
0
0.018
0
0.022
0
0.027
PL
DCON
DC
LF
LCF
OAL
a Suitable for general and deep hole drilling.
DRILLING
DC
LCF OAL
LF
PL DCON
GWSSD0100
GWSSD0110
GWSSD0120
GWSSD0130
GWSSD0140
GWSSD0150
GWSSD0160
GWSSD0170
GWSSD0180
GWSSD0190
GWSSD0200
GWSSD0210
GWSSD0220
GWSSD0230
GWSSD0240
GWSSD0250
GWSSD0260
GWSSD0270
GWSSD0280
GWSSD0290
GWSSD0300
GWSSD0310
GWSSD0320
GWSSD0330
GWSSD0340
GWSSD0350
GWSSD0360
GWSSD0370
GWSSD0380
GWSSD0390
GWSSD0400
GWSSD0410
GWSSD0420
GWSSD0430
GWSSD0440
GWSSD0450
GWSSD0460
GWSSD0470
GWSSD0480
GWSSD0490
1.0
1.1
18.3
20.3
40.3
42.3
40
42
0.3
0.3
1.0
1.1
1.2
20.4
42.4
42
0.4
1.2
1.3
22.4
45.4
45
0.4
1.3
1.4
23.4
48.4
48
0.4
1.4
1.5
23.5
48.5
48
0.5
1.5
1.6
25.5
50.5
50
0.5
1.6
1.7
25.5
50.5
50
0.5
1.7
1.8
28.5
52.5
52
0.5
1.8
1.9
28.6
52.6
52
0.6
1.9
2.0
29.6
55.6
55
0.6
2.0
2.1
29.6
55.6
55
0.6
2.1
2.2
33.7
58.7
58
0.7
2.2
2.3
33.7
58.7
58
0.7
2.3
2.4
35.7
61.7
61
0.7
2.4
2.5
35.8
61.8
61
0.8
2.5
2.6
37.8
64.8
64
0.8
2.6
2.7
37.8
64.8
64
0.8
2.7
2.8
39.8
67.8
67
0.8
2.8
2.9
42.9
71.9
71
0.9
2.9
3.0
42.9
71.9
71
0.9
3.0
3.1
42.9
71.9
71
0.9
3.1
3.2
43.0
72.0
71
1.0
3.2
3.3
46.0
74.0
73
1.0
3.3
3.4
46.0
74.0
73
1.0
3.4
3.5
46.1
74.1
73
1.1
3.5
3.6
49.1
77.1
76
1.1
3.6
3.7
49.1
77.1
76
1.1
3.7
3.8
49.1
77.1
76
1.1
3.8
3.9
52.2
80.2
79
1.2
3.9
4.0
55.2
84.2
83
1.2
4.0
4.1
55.2
84.2
83
1.2
4.1
4.2
55.3
84.3
83
1.3
4.2
4.3
55.3
84.3
83
1.3
4.3
4.4
57.3
87.3
86
1.3
4.4
4.5
57.4
87.4
86
1.4
4.5
4.6
57.4
87.4
86
1.4
4.6
4.7
60.4
90.4
89
1.4
4.7
4.8
4.9
60.4
63.5
90.4
93.5
89
92
1.4
1.5
4.8
4.9
Stock
Order Number
N176
Stock
Unit : mm
Order Number
DC
LCF OAL
GWSSD0500
GWSSD0510
GWSSD0520
GWSSD0530
GWSSD0540
GWSSD0550
GWSSD0560
GWSSD0570
GWSSD0580
GWSSD0590
GWSSD0600
GWSSD0610
GWSSD0620
GWSSD0630
GWSSD0640
GWSSD0650
GWSSD0660
GWSSD0670
GWSSD0680
GWSSD0690
GWSSD0700
GWSSD0710
GWSSD0720
GWSSD0730
GWSSD0740
GWSSD0750
GWSSD0760
GWSSD0770
GWSSD0780
GWSSD0790
GWSSD0800
GWSSD0810
GWSSD0820
GWSSD0830
GWSSD0840
GWSSD0850
GWSSD0860
GWSSD0870
GWSSD0880
GWSSD0890
5.0
5.1
63.5
63.5
93.5
93.5
92
92
1.5
1.5
5.0
5.1
5.2
65.6
96.6
95
1.6
5.2
5.3
65.6
96.6
95
1.6
5.3
5.4
65.6
96.6
95
1.6
5.4
5.5
65.7
96.7
95
1.7
5.5
5.6
68.7
99.7
98
1.7
5.6
5.7
68.7
99.7
98
1.7
5.7
5.8
68.7
99.7
98
1.7
5.8
5.9
68.8
99.8
98
1.8
5.9
6.0
71.8
103.8
102
1.8
6.0
6.1
71.8
103.8
102
1.8
6.1
6.2
71.9
103.9
102
1.9
6.2
6.3
71.9
103.9
102
1.9
6.3
6.4
74.9
106.9
105
1.9
6.4
6.5
75.0
107.0
105
2.0
6.5
6.6
75.0
107.0
105
2.0
6.6
6.7
75.0
107.0
105
2.0
6.7
6.8
75.0
107.0
105
2.0
6.8
6.9
75.1
107.1
105
2.1
6.9
7.0
75.1
107.1
105
2.1
7.0
7.1
77.1
110.1
108
2.1
7.1
7.2
77.2
110.2
108
2.2
7.2
7.3
77.2
110.2
108
2.2
7.3
7.4
80.2
113.2
111
2.2
7.4
7.5
80.3
113.3
111
2.3
7.5
7.6
80.3
113.3
111
2.3
7.6
7.7
83.3
116.3
114
2.3
7.7
7.8
83.3
116.3
114
2.3
7.8
7.9
83.4
116.4
114
2.4
7.9
8.0
83.4
116.4
114
2.4
8.0
8.1
86.4
119.4
117
2.4
8.1
8.2
86.5
119.5
117
2.5
8.2
8.3
86.5
119.5
117
2.5
8.3
8.4
89.5
123.5
121
2.5
8.4
8.5
89.6
123.6
121
2.6
8.5
8.6
89.6
123.6
121
2.6
8.6
8.7
89.6
123.6
121
2.6
8.7
8.8
8.9
91.6
91.7
126.6
126.7
124
124
2.6
2.7
8.8
8.9
LF
PL DCON
HSS
Stock
Unit : mm
Order Number
DC
LCF OAL
LF
PL DCON
GWSSD0900
GWSSD0910
GWSSD0920
GWSSD0930
GWSSD0940
GWSSD0950
GWSSD0960
GWSSD0970
GWSSD0980
GWSSD0990
GWSSD1000
GWSSD1010
GWSSD1020
GWSSD1030
GWSSD1040
GWSSD1050
GWSSD1060
GWSSD1070
GWSSD1080
GWSSD1090
GWSSD1100
GWSSD1110
GWSSD1120
GWSSD1130
GWSSD1140
GWSSD1150
GWSSD1160
GWSSD1170
GWSSD1180
GWSSD1190
GWSSD1200
GWSSD1210
GWSSD1220
GWSSD1230
GWSSD1240
GWSSD1250
GWSSD1260
GWSSD1270
GWSSD1280
GWSSD1290
GWSSD1300
9.0
9.1
91.7 126.7
91.7 126.7
124
124
2.7
2.7
9.0
9.1
9.2
94.8 129.8
127
2.8
9.2
9.3
94.8 129.8
127
2.8
9.3
9.4
94.8 129.8
127
2.8
9.4
9.5
94.9 129.9
127
2.9
9.5
9.6
97.9 132.9
130
2.9
9.6
9.7
97.9 132.9
130
2.9
9.7
9.8
97.9 132.9
130
2.9
9.8
9.9
98.0 133.0
130
3.0
9.9
10.0
98.0 133.0
130
3.0
10.0
10.1 101.0 136.0
133
3.0
10.1
10.2 101.1 136.1
133
3.1
10.2
10.3 101.1 136.1
133
3.1
10.3
10.4 101.1 136.1
133
3.1
10.4
10.5 103.2 140.2
137
3.2
10.5
10.6 103.2 140.2
137
3.2
10.6
10.7 103.2 140.2
137
3.2
10.7
10.8 106.2 143.2
140
3.2
10.8
10.9 106.3 143.3
140
3.3
10.9
11.0 106.3 143.3
140
3.3
11.0
11.1 106.3 143.3
140
3.3
11.1
11.2 109.4 146.4
143
3.4
11.2
11.3 109.4 146.4
143
3.4
11.3
11.4 109.4 146.4
143
3.4
11.4
11.5 109.5 146.5
143
3.5
11.5
11.6
112.5 149.5
146
3.5
11.6
11.7
112.5 149.5
146
3.5
11.7
11.8
112.5 149.5
146
3.5
11.8
11.9
112.6 149.6
146
3.6
11.9
12.0
114.6 152.6
149
3.6
12.0
12.1
114.6 152.6
149
3.6
12.1
12.2
114.7 152.7
149
3.7
12.2
12.3
114.7 152.7
149
3.7
12.3
12.4
117.7 155.7
152
3.7
12.4
12.5
117.8 155.8
152
3.8
12.5
12.6
117.8 155.8
152
3.8
12.6
12.7
117.8 155.8
152
3.8
12.7
12.8
117.8 155.8
152
3.8
12.8
12.9
13.0
117.9 155.9
117.9 155.9
152
152
3.9
3.9
12.9
13.0
DRILLING
CUTTING CONDITIONS
N198
N177

HSS
GWSL
TiN, Extra long
P
Steel
CO HSS
118
Thinning
2 < DC < 3
3<DC < 6
6<DC < 10
10<DC < 13
0
0.014
0
0.018
0
0.022
0
0.027
PL
DCON
DC
LF
LCF
OAL
a Suitable for extra deep hole drilling.
DRILLING
DC
LCF OAL
LF
PL
DCON
GWSLD0200A125
GWSLD0200A160
GWSLD0210A125
GWSLD0210A160
GWSLD0220A125
GWSLD0220A160
GWSLD0230A125
GWSLD0230A160
GWSLD0240A125
GWSLD0240A160
GWSLD0250A125
GWSLD0250A160
GWSLD0260A125
GWSLD0260A160
GWSLD0270A125
GWSLD0270A160
GWSLD0280A125
GWSLD0280A160
GWSLD0290A125
GWSLD0290A160
GWSLD0300A125
GWSLD0300A160
GWSLD0300A200
GWSLD0310A160
GWSLD0310A200
GWSLD0320A160
GWSLD0320A200
GWSLD0330A160
GWSLD0330A200
GWSLD0340A160
GWSLD0340A200
GWSLD0350A160
GWSLD0350A200
GWSLD0360A160
GWSLD0360A200
GWSLD0370A160
GWSLD0370A200
GWSLD0380A160
GWSLD0380A200
GWSLD0390A160
2.0
2.0
80.6 125.6
100.6 160.6
125
160
0.6
0.6
2.0
2.0
2.1
80.6 125.6
125
0.6
2.1
2.1
100.6 160.6
160
0.6
2.1
2.2
80.7 125.7
125
0.7
2.2
2.2
100.7 160.7
160
0.7
2.2
2.3
80.7 125.7
125
0.7
2.3
2.3
100.7 160.7
160
0.7
2.3
2.4
80.7 125.7
125
0.7
2.4
2.4
100.7 160.7
160
0.7
2.4
2.5
80.8 125.8
125
0.8
2.5
2.5
100.8 160.8
160
0.8
2.5
2.6
80.8 125.8
125
0.8
2.6
2.6
100.8 160.8
160
0.8
2.6
2.7
80.8 125.8
125
0.8
2.7
2.7
100.8 160.8
160
0.8
2.7
2.8
80.8 125.8
125
0.8
2.8
2.8
100.8 160.8
160
0.8
2.8
2.9
80.9 125.9
125
0.9
2.9
2.9
100.9 160.9
160
0.9
2.9
3.0
80.9 125.9
125
0.9
3.0
3.0
100.9 160.9
160
0.9
3.0
3.0
125.9 200.9
200
0.9
3.0
3.1
100.9 160.9
160
0.9
3.1
3.1
125.9 200.9
200
0.9
3.1
3.2
101.0 161.0
160
1.0
3.2
3.2
126.0 201.0
200
1.0
3.2
3.3
101.0 161.0
160
1.0
3.3
3.3
126.0 201.0
200
1.0
3.3
3.4
101.0 161.0
160
1.0
3.4
3.4
126.0 201.0
200
1.0
3.4
3.5
101.1 161.1
160
1.1
3.5
3.5
126.1 201.1
200
1.1
3.5
3.6
101.1 161.1
160
1.1
3.6
3.6
126.1 201.1
200
1.1
3.6
3.7
101.1 161.1
160
1.1
3.7
3.7
126.1 201.1
200
1.1
3.7
3.8
101.1 161.1
160
1.1
3.8
3.8
3.9
126.1 201.1
101.2 161.2
200
160
1.1
1.2
3.8
3.9
Stock
Order Number
N178
Stock
Unit : mm
Order Number
DC
LCF OAL
LF
PL
DCON
GWSLD0390A200
GWSLD0400A160
GWSLD0400A200
GWSLD0400A250
GWSLD0410A160
GWSLD0410A200
GWSLD0410A250
GWSLD0420A160
GWSLD0420A200
GWSLD0420A250
GWSLD0430A160
GWSLD0430A200
GWSLD0430A250
GWSLD0440A160
GWSLD0440A200
GWSLD0440A250
GWSLD0450A160
GWSLD0450A200
GWSLD0450A250
GWSLD0460A160
GWSLD0460A200
GWSLD0460A250
GWSLD0470A160
GWSLD0470A200
GWSLD0470A250
GWSLD0480A160
GWSLD0480A200
GWSLD0480A250
GWSLD0490A160
GWSLD0490A200
GWSLD0490A250
GWSLD0500A160
GWSLD0500A200
GWSLD0500A250
GWSLD0510A160
GWSLD0510A200
GWSLD0510A250
GWSLD0520A160
GWSLD0520A200
GWSLD0520A250
3.9
4.0
126.2 201.2
101.2 161.2
200
160
1.2
1.2
3.9
4.0
4.0
126.2 201.2
200
1.2
4.0
4.0
161.2 251.2
250
1.2
4.0
4.1
101.2 161.2
160
1.2
4.1
4.1
126.2 201.2
200
1.2
4.1
4.1
161.2 251.2
250
1.2
4.1
4.2
101.3 161.3
160
1.3
4.2
4.2
126.3 201.3
200
1.3
4.2
4.2
161.3 251.3
250
1.3
4.2
4.3
101.3 161.3
160
1.3
4.3
4.3
126.3 201.3
200
1.3
4.3
4.3
161.3 251.3
250
1.3
4.3
4.4
101.3 161.3
160
1.3
4.4
4.4
126.3 201.3
200
1.3
4.4
4.4
161.3 251.3
250
1.3
4.4
4.5
101.4 161.4
160
1.4
4.5
4.5
126.4 201.4
200
1.4
4.5
4.5
161.4 251.4
250
1.4
4.5
4.6
101.4 161.4
160
1.4
4.6
4.6
126.4 201.4
200
1.4
4.6
4.6
161.4 251.4
250
1.4
4.6
4.7
101.4 161.4
160
1.4
4.7
4.7
126.4 201.4
200
1.4
4.7
4.7
161.4 251.4
250
1.4
4.7
4.8
101.4 161.4
160
1.4
4.8
4.8
126.4 201.4
200
1.4
4.8
4.8
161.4 251.4
250
1.4
4.8
4.9
101.5 161.5
160
1.5
4.9
4.9
126.5 201.5
200
1.5
4.9
4.9
161.5 251.5
250
1.5
4.9
5.0
101.5 161.5
160
1.5
5.0
5.0
126.5 201.5
200
1.5
5.0
5.0
161.5 251.5
250
1.5
5.0
5.1
101.5 161.5
160
1.5
5.1
5.1
126.5 201.5
200
1.5
5.1
5.1
161.5 251.5
250
1.5
5.1
5.2
101.6 161.6
160
1.6
5.2
5.2
5.2
126.6 201.6
161.6 251.6
200
250
1.6
1.6
5.2
5.2
HSS
DC
LCF OAL
LF
PL
DCON
GWSLD0530A160
GWSLD0530A200
GWSLD0530A250
GWSLD0540A160
GWSLD0540A200
GWSLD0540A250
GWSLD0550A160
GWSLD0550A200
GWSLD0550A250
GWSLD0560A160
GWSLD0560A200
GWSLD0560A250
GWSLD0570A160
GWSLD0570A200
GWSLD0570A250
GWSLD0580A160
GWSLD0580A200
GWSLD0580A250
GWSLD0590A160
GWSLD0590A200
GWSLD0590A250
GWSLD0600A160
GWSLD0600A200
GWSLD0600A250
GWSLD0600A315
GWSLD0650A160
GWSLD0650A200
GWSLD0650A250
GWSLD0650A315
GWSLD0680A160
GWSLD0680A200
GWSLD0680A250
GWSLD0680A315
GWSLD0700A160
GWSLD0700A200
GWSLD0700A250
GWSLD0700A315
GWSLD0750A200
GWSLD0750A250
GWSLD0750A315
GWSLD0800A200
GWSLD0800A250
GWSLD0800A315
GWSLD0850A200
GWSLD0850A250
GWSLD0850A315
GWSLD0900A200
GWSLD0900A250
GWSLD0900A315
GWSLD0950A200
5.3
5.3
101.6 161.6
126.6 201.6
160
200
1.6
1.6
5.3
5.3
5.3
161.6 251.6
250
1.6
5.3
5.4
101.6 161.6
160
1.6
5.4
5.4
126.6 201.6
200
1.6
5.4
5.4
161.6 251.6
250
1.6
5.4
5.5
101.7 161.7
160
1.7
5.5
5.5
126.7 201.7
200
1.7
5.5
5.5
161.7 251.7
250
1.7
5.5
5.6
101.7 161.7
160
1.7
5.6
5.6
126.7 201.7
200
1.7
5.6
5.6
161.7 251.7
250
1.7
5.6
5.7
101.7 161.7
160
1.7
5.7
5.7
126.7 201.7
200
1.7
5.7
5.7
161.7 251.7
250
1.7
5.7
5.8
101.7 161.7
160
1.7
5.8
5.8
126.7 201.7
200
1.7
5.8
5.8
161.7 251.7
250
1.7
5.8
5.9
101.8 161.8
160
1.8
5.9
5.9
126.8 201.8
200
1.8
5.9
5.9
161.8 251.8
250
1.8
5.9
6.0
101.8 161.8
160
1.8
6.0
6.0
126.8 201.8
200
1.8
6.0
6.0
161.8 251.8
250
1.8
6.0
6.0
201.8 316.8
315
1.8
6.0
6.5
102.0 162.0
160
2.0
6.5
6.5
127.0 202.0
200
2.0
6.5
6.5
162.0 252.0
250
2.0
6.5
6.5
202.0 317.0
315
2.0
6.5
6.8
102.0 162.0
160
2.0
6.8
6.8
127.0 202.0
200
2.0
6.8
6.8
162.0 252.0
250
2.0
6.8
6.8
202.0 317.0
315
2.0
6.8
7.0
102.1 162.1
160
2.1
7.0
7.0
127.1 202.1
200
2.1
7.0
7.0
162.1 252.1
250
2.1
7.0
7.0
202.1 317.1
315
2.1
7.0
7.5
127.3 202.3
200
2.3
7.5
7.5
162.3 252.3
250
2.3
7.5
7.5
202.3 317.3
315
2.3
7.5
8.0
127.4 202.4
200
2.4
8.0
8.0
162.4 252.4
250
2.4
8.0
8.0
202.4 317.4
315
2.4
8.0
8.5
142.6 202.6
200
2.6
8.5
8.5
162.6 252.6
250
2.6
8.5
8.5
202.6 317.6
315
2.6
8.5
9.0
142.7 202.7
200
2.7
9.0
9.0
162.7 252.7
250
2.7
9.0
9.0
9.5
202.7 317.7
142.9 202.9
315
200
2.7
2.9
9.0
9.5
Order Number
DC
LCF OAL
LF
PL
DCON
GWSLD0950A250
GWSLD0950A315
GWSLD1000A200
GWSLD1000A250
GWSLD1000A315
GWSLD1050A250
GWSLD1050A315
GWSLD1100A250
GWSLD1100A315
GWSLD1150A250
GWSLD1150A315
GWSLD1200A250
GWSLD1200A315
GWSLD1250A250
GWSLD1250A315
GWSLD1300A250
GWSLD1300A315
9.5
9.5
162.9 252.9
202.9 317.9
250
315
2.9
2.9
9.5
9.5
10.0
143.0 203.0
200
3.0
10.0
10.0
163.0 253.0
250
3.0
10.0
10.0
203.0 318.0
315
3.0
10.0
10.5
163.2 253.2
250
3.2
10.5
10.5
203.2 318.2
315
3.2
10.5
11.0
163.3 253.3
250
3.3
11.0
11.0
203.3 318.3
315
3.3
11.0
11.5
163.5 253.5
250
3.5
11.5
11.5
203.5 318.5
315
3.5
11.5
12.0
163.6 253.6
250
3.6
12.0
12.0
203.6 318.6
315
3.6
12.0
12.5
163.8 253.8
250
3.8
12.5
12.5
203.8 318.8
315
3.8
12.5
13.0
13.0
163.9 253.9
203.9 318.9
250
315
3.9
3.9
13.0
13.0
DRILLING
Order Number
Stock
Stock
Unit : mm
CUTTING CONDITIONS
N198
N179

HSS
LSD
Extra long
P
Steel
118
HSS
Thinning
1 < DC < 3
3<DC < 6
6<DC < 10
10<DC < 13
0
0.014
0
0.018
0
0.022
0
0.027
PL
DCON
DC
LF
LCF
OAL
a Widely used for deep hole drilling.
DRILLING
DC
LCF OAL
LF
PL DCON
LSDD0100A100
LSDD0100A150
LSDD0110A100
LSDD0110A150
LSDD0120A100
LSDD0120A150
LSDD0130A100
LSDD0130A150
LSDD0140A100
LSDD0140A150
LSDD0150A100
LSDD0150A150
LSDD0160A100
LSDD0160A150
LSDD0170A100
LSDD0170A150
LSDD0180A100
LSDD0180A150
LSDD0190A100
LSDD0190A150
LSDD0200A100
LSDD0200A125
LSDD0200A150
LSDD0210A100
LSDD0210A150
LSDD0220A100
LSDD0220A150
LSDD0230A100
LSDD0230A150
LSDD0240A100
LSDD0240A150
LSDD0250A100
LSDD0250A125
LSDD0250A150
LSDD0260A100
LSDD0260A150
LSDD0270A100
LSDD0270A150
LSDD0280A100
LSDD0280A150
1.0
1.0
25.3 100.3
25.3 150.3
100
150
0.3
0.3
1.0
1.0
1.1
25.3 100.3
100
0.3
1.1
1.1
25.3 150.3
150
0.3
1.1
1.2
25.4 100.4
100
0.4
1.2
1.2
25.4 150.4
150
0.4
1.2
1.3
30.4 100.4
100
0.4
1.3
1.3
30.4 150.4
150
0.4
1.3
1.4
30.4 100.4
100
0.4
1.4
1.4
30.4 150.4
150
0.4
1.4
1.5
30.5 100.5
100
0.5
1.5
1.5
30.5 150.5
150
0.5
1.5
1.6
40.5 100.5
100
0.5
1.6
1.6
40.5 150.5
150
0.5
1.6
1.7
40.5 100.5
100
0.5
1.7
1.7
40.5 150.5
150
0.5
1.7
1.8
40.5 100.5
100
0.5
1.8
1.8
40.5 150.5
150
0.5
1.8
1.9
40.6 100.6
100
0.6
1.9
1.9
40.6 150.6
150
0.6
1.9
2.0
50.6 100.6
100
0.6
2.0
2.0
65.6 125.6
125
0.6
2.0
2.0
75.6 150.6
150
0.6
2.0
2.1
50.6 100.6
100
0.6
2.1
2.1
75.6 150.6
150
0.6
2.1
2.2
50.7 100.7
100
0.7
2.2
2.2
75.7 150.7
150
0.7
2.2
2.3
50.7 100.7
100
0.7
2.3
2.3
75.7 150.7
150
0.7
2.3
2.4
50.7 100.7
100
0.7
2.4
2.4
75.7 150.7
150
0.7
2.4
2.5
50.8 100.8
100
0.8
2.5
2.5
65.8 125.8
125
0.8
2.5
2.5
75.8 150.8
150
0.8
2.5
2.6
50.8 100.8
100
0.8
2.6
2.6
75.8 150.8
150
0.8
2.6
2.7
50.8 100.8
100
0.8
2.7
2.7
75.8 150.8
150
0.8
2.7
2.8
2.8
50.8 100.8
75.8 150.8
100
150
0.8
0.8
2.8
2.8
Stock
Order Number
N180
Stock
Unit : mm
Order Number
DC
LCF OAL
LF
PL DCON
LSDD0290A100
LSDD0290A150
LSDD0300A100
LSDD0300A125
LSDD0300A150
LSDD0300A200
LSDD0310A150
LSDD0310A200
LSDD0320A125
LSDD0320A150
LSDD0320A200
LSDD0320A250
LSDD0330A150
LSDD0330A200
LSDD0340A150
LSDD0340A200
LSDD0350A125
LSDD0350A150
LSDD0350A200
LSDD0350A250
LSDD0360A150
LSDD0360A200
LSDD0370A150
LSDD0370A200
LSDD0380A150
LSDD0380A200
LSDD0390A150
LSDD0390A200
LSDD0400A125
LSDD0400A150
LSDD0400A200
LSDD0400A250
LSDD0410A150
LSDD0410A200
LSDD0420A150
LSDD0420A200
LSDD0430A150
LSDD0430A200
LSDD0440A150
LSDD0440A200
2.9
2.9
50.9 100.9
75.9 150.9
100
150
0.9
0.9
2.9
2.9
3.0
50.9 100.9
100
0.9
3.0
3.0
65.9 125.9
125
0.9
3.0
3.0
75.9 150.9
150
0.9
3.0
3.0
100.9 200.9
200
0.9
3.0
3.1
75.9 150.9
150
0.9
3.1
3.1
100.9 200.9
200
0.9
3.1
3.2
66.0 126.0
125
1.0
3.2
3.2
76.0 151.0
150
1.0
3.2
3.2
101.0 201.0
200
1.0
3.2
3.2
131.0 251.0
250
1.0
3.2
3.3
76.0 151.0
150
1.0
3.3
3.3
101.0 201.0
200
1.0
3.3
3.4
76.0 151.0
150
1.0
3.4
3.4
101.0 201.0
200
1.0
3.4
3.5
66.1 126.1
125
1.1
3.5
3.5
76.1 151.1
150
1.1
3.5
3.5
101.1 201.1
200
1.1
3.5
3.5
131.1 251.1
250
1.1
3.5
3.6
76.1 151.1
150
1.1
3.6
3.6
101.1 201.1
200
1.1
3.6
3.7
76.1 151.1
150
1.1
3.7
3.7
101.1 201.1
200
1.1
3.7
3.8
76.1 151.1
150
1.1
3.8
3.8
101.1 201.1
200
1.1
3.8
3.9
76.2 151.2
150
1.2
3.9
3.9
101.2 201.2
200
1.2
3.9
4.0
71.2 126.2
125
1.2
4.0
4.0
76.2 151.2
150
1.2
4.0
4.0
101.2 201.2
200
1.2
4.0
4.0
131.2 251.2
250
1.2
4.0
4.1
76.2 151.2
150
1.2
4.1
4.1
101.2 201.2
200
1.2
4.1
4.2
76.3 151.3
150
1.3
4.2
4.2
101.3 201.3
200
1.3
4.2
4.3
76.3 151.3
150
1.3
4.3
4.3
101.3 201.3
200
1.3
4.3
4.4
4.4
76.3 151.3
101.3 201.3
150
200
1.3
1.3
4.4
4.4
a
a
HSS
DC
LCF OAL
LF
PL DCON
LSDD0450A125
LSDD0450A150
LSDD0450A200
LSDD0450A250
LSDD0460A150
LSDD0460A200
LSDD0470A150
LSDD0470A200
LSDD0480A150
LSDD0480A200
LSDD0480A250
LSDD0490A150
LSDD0490A200
LSDD0500A150
LSDD0500A200
LSDD0500A250
LSDD0500A300
LSDD0510A200
LSDD0510A250
LSDD0520A200
LSDD0520A250
LSDD0530A200
LSDD0530A250
LSDD0530A300
LSDD0540A200
LSDD0540A250
LSDD0540A300
LSDD0550A150
LSDD0550A200
LSDD0550A250
LSDD0550A300
LSDD0560A200
LSDD0560A250
LSDD0570A200
LSDD0570A250
LSDD0580A200
LSDD0580A250
LSDD0590A200
LSDD0590A250
LSDD0600A150
LSDD0600A200
LSDD0600A250
LSDD0600A300
LSDD0610A200
LSDD0610A250
LSDD0610A300
LSDD0620A200
LSDD0620A250
LSDD0620A300
LSDD0630A200
4.5
4.5
71.4 126.4
76.4 151.4
125
150
1.4
1.4
4.5
4.5
4.5
101.4 201.4
200
1.4
4.5
4.5
131.4 251.4
250
1.4
4.5
4.6
91.4 151.4
150
1.4
4.6
4.6
101.4 201.4
200
1.4
4.6
4.7
91.4 151.4
150
1.4
4.7
4.7
101.4 201.4
200
1.4
4.7
4.8
91.4 151.4
150
1.4
4.8
4.8
101.4 201.4
200
1.4
4.8
4.8
131.4 251.4
250
1.4
4.8
4.9
91.5 151.5
150
1.5
4.9
4.9
101.5 201.5
200
1.5
4.9
5.0
91.5 151.5
150
1.5
5.0
5.0
101.5 201.5
200
1.5
5.0
5.0
131.5 251.5
250
1.5
5.0
5.0
151.5 301.5
300
1.5
5.0
5.1
101.5 201.5
200
1.5
5.1
5.1
131.5 251.5
250
1.5
5.1
5.2
101.6 201.6
200
1.6
5.2
5.2
131.6 251.6
250
1.6
5.2
5.3
101.6 201.6
200
1.6
5.3
5.3
131.6 251.6
250
1.6
5.3
5.3
151.6 301.6
300
1.6
5.3
5.4
101.6 201.6
200
1.6
5.4
5.4
131.6 251.6
250
1.6
5.4
5.4
151.6 301.6
300
1.6
5.4
5.5
91.7 151.7
150
1.7
5.5
5.5
101.7 201.7
200
1.7
5.5
5.5
131.7 251.7
250
1.7
5.5
5.5
151.7 301.7
300
1.7
5.5
5.6
101.7 201.7
200
1.7
5.6
5.6
131.7 251.7
250
1.7
5.6
5.7
101.7 201.7
200
1.7
5.7
5.7
131.7 251.7
250
1.7
5.7
5.8
101.7 201.7
200
1.7
5.8
5.8
131.7 251.7
250
1.7
5.8
5.9
101.8 201.8
200
1.8
5.9
5.9
131.8 251.8
250
1.8
5.9
6.0
91.8 151.8
150
1.8
6.0
6.0
101.8 201.8
200
1.8
6.0
6.0
131.8 251.8
250
1.8
6.0
6.0
151.8 301.8
300
1.8
6.0
6.1
121.8 201.8
200
1.8
6.1
6.1
131.8 251.8
250
1.8
6.1
6.1
151.8 301.8
300
1.8
6.1
6.2
121.9 201.9
200
1.9
6.2
6.2
131.9 251.9
250
1.9
6.2
6.2
6.3
151.9 301.9
121.9 201.9
300
200
1.9
1.9
6.2
6.3
Order Number
DC
LCF OAL
LF
PL DCON
LSDD0630A250
LSDD0630A300
LSDD0640A200
LSDD0640A250
LSDD0640A300
LSDD0650A150
LSDD0650A200
LSDD0650A250
LSDD0650A300
LSDD0660A200
LSDD0660A250
LSDD0670A200
LSDD0670A250
LSDD0680A200
LSDD0680A250
LSDD0690A200
LSDD0690A250
LSDD0690A300
LSDD0700A150
LSDD0700A200
LSDD0700A250
LSDD0700A300
LSDD0710A200
LSDD0710A250
LSDD0710A300
LSDD0720A200
LSDD0720A250
LSDD0720A300
LSDD0730A200
LSDD0730A250
LSDD0730A300
LSDD0740A250
LSDD0740A300
LSDD0750A150
LSDD0750A200
LSDD0750A250
LSDD0750A300
LSDD0760A200
LSDD0760A250
LSDD0760A300
LSDD0770A200
LSDD0770A250
LSDD0770A300
LSDD0780A200
LSDD0780A250
LSDD0780A300
LSDD0790A200
LSDD0790A250
LSDD0800A150
LSDD0800A200
6.3
6.3
131.9 251.9
151.9 301.9
250
300
1.9
1.9
6.3
6.3
6.4
121.9 201.9
200
1.9
6.4
6.4
131.9 251.9
250
1.9
6.4
6.4
151.9 301.9
300
1.9
6.4
6.5
92.0 152.0
150
2.0
6.5
6.5
122.0 202.0
200
2.0
6.5
6.5
132.0 252.0
250
2.0
6.5
6.5
152.0 302.0
300
2.0
6.5
6.6
122.0 202.0
200
2.0
6.6
6.6
132.0 252.0
250
2.0
6.6
6.7
122.0 202.0
200
2.0
6.7
6.7
132.0 252.0
250
2.0
6.7
6.8
122.0 202.0
200
2.0
6.8
6.8
132.0 252.0
250
2.0
6.8
6.9
122.1 202.1
200
2.1
6.9
6.9
132.1 252.1
250
2.1
6.9
6.9
152.1 302.1
300
2.1
6.9
7.0
92.1 152.1
150
2.1
7.0
7.0
122.1 202.1
200
2.1
7.0
7.0
132.1 252.1
250
2.1
7.0
7.0
152.1 302.1
300
2.1
7.0
7.1
122.1 202.1
200
2.1
7.1
7.1
132.1 252.1
250
2.1
7.1
7.1
152.1 302.1
300
2.1
7.1
7.2
122.2 202.2
200
2.2
7.2
7.2
132.2 252.2
250
2.2
7.2
7.2
152.2 302.2
300
2.2
7.2
7.3
122.2 202.2
200
2.2
7.3
7.3
132.2 252.2
250
2.2
7.3
7.3
152.2 302.2
300
2.2
7.3
7.4
132.2 252.2
250
2.2
7.4
7.4
152.2 302.2
300
2.2
7.4
7.5
92.3 152.3
150
2.3
7.5
7.5
122.3 202.3
200
2.3
7.5
7.5
132.3 252.3
250
2.3
7.5
7.5
152.3 302.3
300
2.3
7.5
7.6
122.3 202.3
200
2.3
7.6
7.6
132.3 252.3
250
2.3
7.6
7.6
152.3 302.3
300
2.3
7.6
7.7
122.3 202.3
200
2.3
7.7
7.7
132.3 252.3
250
2.3
7.7
7.7
152.3 302.3
300
2.3
7.7
7.8
122.3 202.3
200
2.3
7.8
7.8
132.3 252.3
250
2.3
7.8
7.8
152.3 302.3
300
2.3
7.8
7.9
122.4 202.4
200
2.4
7.9
7.9
132.4 252.4
250
2.4
7.9
8.0
8.0
92.4 152.4
122.4 202.4
150
200
2.4
2.4
8.0
8.0
CUTTING CONDITIONS
DRILLING
Order Number
Stock
Stock
Unit : mm
N199
N181

HSS
LSD
Extra long
DRILLING
LSDD0800A250
LSDD0800A300
LSDD0810A250
LSDD0810A300
LSDD0810A350
LSDD0820A250
LSDD0820A300
LSDD0830A250
LSDD0830A300
LSDD0840A200
LSDD0840A250
LSDD0840A300
LSDD0850A200
LSDD0850A250
LSDD0850A300
LSDD0850A350
LSDD0860A250
LSDD0870A250
LSDD0870A300
LSDD0880A200
LSDD0880A250
LSDD0880A300
LSDD0890A200
LSDD0890A250
LSDD0890A300
LSDD0900A200
LSDD0900A250
LSDD0900A300
LSDD0900A350
LSDD0910A250
LSDD0910A300
LSDD0920A250
LSDD0920A300
LSDD0930A250
LSDD0930A300
LSDD0940A250
LSDD0940A300
LSDD0950A200
LSDD0950A250
LSDD0950A300
LSDD0950A350
LSDD0960A250
LSDD0960A300
LSDD0970A250
LSDD0970A300
LSDD0980A250
LSDD0980A300
LSDD0990A250
LSDD0990A300
LSDD1000A200
N182
DC
LCF OAL
LF
PL DCON
8.0 132.4 252.4

8.0 152.4 302.4
250
300
2.4
2.4
8.0
8.0
8.1 132.4 252.4
250
2.4
8.1
8.1 182.4 302.4
300
2.4
8.1
8.1 202.4 352.4
350
2.4
8.1
8.2 132.5 252.5
250
2.5
8.2
8.2 182.5 302.5
300
2.5
8.2
8.3 132.5 252.5
250
2.5
8.3
8.3 182.5 302.5
300
2.5
8.3
8.4 122.5 202.5
200
2.5
8.4
8.4 132.5 252.5
250
2.5
8.4
8.4 182.5 302.5
300
2.5
8.4
8.5 122.6 202.6
200
2.6
8.5
8.5 132.6 252.6
250
2.6
8.5
8.5 182.6 302.6
300
2.6
8.5
8.5 202.6 352.6
350
2.6
8.5
8.6 132.6 252.6
250
2.6
8.6
8.7 132.6 252.6
250
2.6
8.7
8.7 182.6 302.6
300
2.6
8.7
8.8 122.6 202.6
200
2.6
8.8
8.8 132.6 252.6
250
2.6
8.8
8.8 182.6 302.6
300
2.6
8.8
8.9 122.7 202.7
200
2.7
8.9
8.9 132.7 252.7
250
2.7
8.9
8.9 182.7 302.7
300
2.7
8.9
9.0 122.7 202.7
200
2.7
9.0
9.0 132.7 252.7
250
2.7
9.0
9.0 182.7 302.7
300
2.7
9.0
9.0 202.7 352.7
350
2.7
9.0
9.1 132.7 252.7
250
2.7
9.1
9.1 182.7 302.7
300
2.7
9.1
9.2 132.8 252.8
250
2.8
9.2
9.2 182.8 302.8
300
2.8
9.2
9.3 132.8 252.8
250
2.8
9.3
9.3 182.8 302.8
300
2.8
9.3
9.4 132.8 252.8
250
2.8
9.4
9.4 182.8 302.8
300
2.8
9.4
9.5 122.9 202.9
200
2.9
9.5
9.5 132.9 252.9
250
2.9
9.5
9.5 182.9 302.9
300
2.9
9.5
9.5 202.9 352.9
350
2.9
9.5
9.6 132.9 252.9
250
2.9
9.6
9.6 182.9 302.9
300
2.9
9.6
9.7 132.9 252.9
250
2.9
9.7
9.7 182.9 302.9
300
2.9
9.7
9.8 132.9 252.9
250
2.9
9.8
9.8 182.9 302.9
300
2.9
9.8
9.9 133.0 253.0
250
3.0
9.9
9.9 183.0 303.0

10.0 123.0 203.0
300
200
3.0
3.0
9.9
10.0
Order Number
LSDD1000A250
LSDD1000A300
LSDD1000A350
LSDD1010A250
LSDD1010A300
LSDD1020A250
LSDD1020A300
LSDD1030A250
LSDD1030A300
LSDD1040A250
LSDD1040A300
LSDD1050A200
LSDD1050A250
LSDD1050A300
LSDD1050A350
LSDD1060A300
LSDD1070A300
LSDD1080A300
LSDD1090A300
LSDD1100A200
LSDD1100A250
LSDD1100A300
LSDD1100A350
LSDD1110A250
LSDD1110A350
LSDD1120A250
LSDD1120A350
LSDD1130A250
LSDD1130A350
LSDD1140A250
LSDD1140A350
LSDD1150A200
LSDD1150A250
LSDD1150A300
LSDD1150A350
LSDD1200A200
LSDD1200A250
LSDD1200A300
LSDD1200A350
LSDD1250A200
LSDD1250A250
LSDD1250A300
LSDD1250A350
LSDD1300A200
LSDD1300A250
LSDD1300A300
LSDD1300A350
DC
Stock
Order Number
Stock
Unit : mm
LCF OAL
LF
PL DCON
10.0 133.0 253.0

10.0 183.0 303.0
250
300
3.0
3.0
10.0
10.0
10.0 203.0 353.0
350
3.0
10.0
10.1 133.0 253.0
250
3.0
10.1
10.1 183.0 303.0
300
3.0
10.1
10.2 133.1 253.1
250
3.1
10.2
10.2 183.1 303.1
300
3.1
10.2
10.3 133.1 253.1
250
3.1
10.3
10.3 183.1 303.1
300
3.1
10.3
10.4 133.1 253.1
250
3.1
10.4
10.4 183.1 303.1
300
3.1
10.4
10.5 123.2 203.2
200
3.2
10.5
10.5 133.2 253.2
250
3.2
10.5
10.5 183.2 303.2
300
3.2
10.5
10.5 203.2 353.2
350
3.2
10.5
10.6 183.2 303.2
300
3.2
10.6
10.7 183.2 303.2
300
3.2
10.7
10.8 183.2 303.2
300
3.2
10.8
10.9 183.3 303.3
300
3.3
10.9
11.0
123.3 203.3
200
3.3
11.0
11.0
133.3 253.3
250
3.3
11.0
11.0
183.3 303.3
300
3.3
11.0
11.0
203.3 353.3
350
3.3
11.0
11.1
133.3 253.3
250
3.3
11.1
11.1
203.3 353.3
350
3.3
11.1
11.2
133.4 253.4
250
3.4
11.2
11.2
203.4 353.4
350
3.4
11.2
11.3
133.4 253.4
250
3.4
11.3
11.3
203.4 353.4
350
3.4
11.3
11.4
133.4 253.4
250
3.4
11.4
11.4
203.4 353.4
350
3.4
11.4
11.5
123.5 203.5
200
3.5
11.5
11.5
133.5 253.5
250
3.5
11.5
11.5
183.5 303.5
300
3.5
11.5
11.5
203.5 353.5
350
3.5
11.5
12.0 123.6 203.6
200
3.6
12.0
12.0 133.6 253.6
250
3.6
12.0
12.0 183.6 303.6
300
3.6
12.0
12.0 203.6 353.6
350
3.6
12.0
12.5 123.8 203.8
200
3.8
12.5
12.5 133.8 253.8
250
3.8
12.5
12.5 183.8 303.8
300
3.8
12.5
12.5 203.8 353.8
350
3.8
12.5
13.0 123.9 203.9
200
3.9
13.0
13.0 133.9 253.9
250
3.9
13.0
13.0 183.9 303.9

13.0 203.9 353.9
300
350
3.9
3.9
13.0
13.0

CUTTING CONDITIONS
N199
EPSS
Plate pal
P
Steel
170
HSS
110
Thinning
2 < DC < 3
3<DC < 6
6<DC < 10
10<DC < 13
0
0.014
0
0.018
0
0.022
0
0.027
PL
HSS
DCON
DC
LF
LCF
a Special cutting edge geometry to prevent through hole burrs.
DC
LCF
LF
PL
DCON
EPSSD0200
EPSSD0210
EPSSD0220
EPSSD0230
EPSSD0240
EPSSD0250
EPSSD0260
EPSSD0270
EPSSD0280
EPSSD0290
EPSSD0300
EPSSD0310
EPSSD0320
EPSSD0330
EPSSD0340
EPSSD0350
EPSSD0360
EPSSD0370
EPSSD0380
EPSSD0390
EPSSD0400
EPSSD0410
EPSSD0420
EPSSD0430
EPSSD0440
EPSSD0450
EPSSD0460
EPSSD0470
EPSSD0480
EPSSD0490
EPSSD0500
EPSSD0510
EPSSD0520
EPSSD0530
EPSSD0540
EPSSD0550
EPSSD0600
EPSSD0650
EPSSD0680
EPSSD0700
2.0
2.1
17
17
48
48
0.3
0.3
2.0
2.1
2.2
17
48
0.3
2.2
2.3
17
48
0.3
2.3
2.4
17
48
0.3
2.4
2.5
17
48
0.4
2.5
2.6
17
48
0.4
2.6
2.7
17
48
0.4
2.7
2.8
17
48
0.4
2.8
2.9
17
48
0.4
2.9
3.0
17
48
0.5
3.0
3.1
17
48
0.5
3.1
3.2
17
48
0.5
3.2
3.3
17
48
0.5
3.3
3.4
19
51
0.5
3.4
3.5
19
51
0.6
3.5
3.6
19
51
0.6
3.6
3.7
19
51
0.6
3.7
3.8
21
54
0.6
3.8
3.9
21
54
0.6
3.9
4.0
21
54
0.6
4.0
4.1
21
54
0.6
4.1
4.2
21
54
0.6
4.2
4.3
23
57
0.6
4.3
4.4
23
57
0.6
4.4
4.5
23
57
0.7
4.5
4.6
23
57
0.7
4.6
4.7
23
57
0.7
4.7
4.8
24
60
0.7
4.8
4.9
24
60
0.7
4.9
5.0
24
60
0.8
5.0
5.1
24
60
0.8
5.1
5.2
24
60
0.8
5.2
5.3
24
60
0.8
5.3
5.4
26
64
0.8
5.4
5.5
26
64
0.9
5.5
6.0
26
64
1.0
6.0
6.5
29
68
1.0
6.5
6.8
7.0
32
32
72
72
1.1
1.1
6.8
7.0
Order Number
DC
EPSSD0750
EPSSD0800
EPSSD0820
EPSSD0850
EPSSD0900
EPSSD0950
EPSSD1000
EPSSD1020
EPSSD1030
EPSSD1050
EPSSD1100
EPSSD1150
EPSSD1200
EPSSD1250
EPSSD1300
LCF
LF
PL
DCON
7.5
8.0
32
34
72
76
1.2
1.3
7.5
8.0
8.2
34
76
1.3
8.2
8.5
34
76
1.4
8.5
9.0
37
81
1.5
9.0
9.5
37
81
1.6
9.5
10.0
40
86
1.6
10.0
10.2
40
86
1.6
10.2
10.3
40
86
1.6
10.3
10.5
40
86
1.7
10.5
11.0
43
91
1.8
11.0
11.5
43
91
1.9
11.5
12.0
47
98
2.0
12.0
12.5
13.0
47
47
98
98
2.0
2.2
12.5
13.0
DRILLING
Order Number
Stock
Stock
Unit : mm
N183
TAPER SHANK DRILLS

HSS
GTD
TiN
P
Steel
HSS
DC=6
0
0.018
118
Thinning
6<DC < 10 10<DC < 1818<DC < 3030<DC < 40

0
0.022
0
0.027
PL
0
0.033
0
0.039
DC
LF
CZC
LCF
OAL
a Original manufacturing and coating technology for improved
performance.
DRILLING
DC
GTDD0600M1
GTDD0650M1
GTDD0660M1
GTDD0680M1
GTDD0700M1
GTDD0720M1
GTDD0750M1
GTDD0770M1
GTDD0780M1
GTDD0800M1
GTDD0820M1
GTDD0850M1
GTDD0880M1
GTDD0900M1
GTDD0950M1
GTDD0970M1
GTDD0980M1
GTDD1000M1
GTDD1030M1
GTDD1050M1
GTDD1080M1
GTDD1100M1
GTDD1150M1
GTDD1200M1
GTDD1250M1
GTDD1300M1
GTDD1350M1
GTDD1400M1
GTDD1450M2
GTDD1500M2
GTDD1550M2
GTDD1600M2
GTDD1650M2
GTDD1700M2
GTDD1750M2
GTDD1800M2
GTDD1850M2
GTDD1900M2
GTDD1950M2
GTDD2000M2
N184
LCF
OAL
LF
PL
CZC
6.0
6.5
56.8 149.8
63.0 154.0
148
152
1.8
2.0
MT.1
MT.1
6.6
63.0 157.0
155
2.0
MT.1
6.8
69.0 157.0
155
2.0
MT.1
7.0
69.1 157.1
155
2.1
MT.1
7.2
69.2 160.2
158
2.2
MT.1
7.5
69.3 160.3
158
2.3
MT.1
7.7
74.3 164.3
162
2.3
MT.1
7.8
74.3 164.3
162
2.3
MT.1
8.0
74.4 164.4
162
2.4
MT.1
8.2
74.5 170.5
168
2.5
MT.1
8.5
74.6 170.6
168
2.6
MT.1
8.8
80.6 174.6
172
2.6
MT.1
9.0
80.7 174.7
172
2.7
MT.1
9.5
80.9 177.9
175
2.9
MT.1
9.7
86.9 180.9
178
2.9
MT.1
9.8
86.9 180.9
178
2.9
MT.1
10.0
87.0 181.0
178
3.0
MT.1
10.3
87.1 185.1
182
3.1
MT.1
10.5
87.2 185.2
182
3.2
MT.1
10.8
93.2 188.2
185
3.2
MT.1
11.0
93.3 188.3
185
3.3
MT.1
11.5
93.5 191.5
188
3.5
MT.1
12.0
100.6 195.6
192
3.6
MT.1
12.5
100.8 198.8
195
3.8
MT.1
13.0
100.9 201.9
198
3.9
MT.1
13.5
107.1 206.1
202
4.1
MT.1
14.0
107.2 209.2
205
4.2
MT.1
14.5
113.4 226.4
222
4.4
MT.2
15.0
113.5 229.5
225
4.5
MT.2
15.5
119.7 232.7
228
4.7
MT.2
16.0
119.8 234.8
230
4.8
MT.2
16.5
124.0 237.0
232
5.0
MT.2
17.0
124.1 240.1
235
5.1
MT.2
17.5
129.3 245.3
240
5.3
MT.2
18.0
129.4 245.4
240
5.4
MT.2
18.5
134.6 250.6
245
5.6
MT.2
19.0
134.7 250.7
245
5.7
MT.2
19.5
20.0
138.9 255.9
139.0 256.0
250
250
5.9
6.0
MT.2
MT.2
Stock
Order Number
Stock
Unit : mm
Order Number
DC
LCF
OAL
LF
PL
CZC
GTDD2050M2
GTDD2100M2
GTDD2150M2
GTDD2150M3
GTDD2200M2
GTDD2200M3
GTDD2250M2
GTDD2250M3
GTDD2300M2
GTDD2300M3
GTDD2350M3
GTDD2400M3
GTDD2450M3
GTDD2500M3
GTDD2550M3
GTDD2600M3
GTDD2650M3
GTDD2700M3
GTDD2750M3
GTDD2800M3
GTDD2850M3
GTDD2900M3
GTDD2950M3
GTDD3000M3
GTDD3050M3
GTDD3100M3
GTDD3150M3
GTDD3200M3
GTDD3300M4
GTDD3400M4
GTDD3500M4
GTDD3600M4
GTDD3700M4
GTDD3800M4
GTDD3900M4
GTDD4000M4
20.5
21.0
144.2 261.2
144.3 261.3
255
255
6.2
6.3
MT.2
MT.2
21.5
149.5 266.5
260
6.5
MT.2
21.5
149.5 286.5
280
6.5
MT.3
22.0
149.6 266.6
260
6.6
MT.2
22.0
149.6 286.6
280
6.6
MT.3
22.5
153.8 271.8
265
6.8
MT.2
22.5
153.8 291.8
285
6.8
MT.3
23.0
153.9 271.9
265
6.9
MT.2
23.0
153.9 291.9
285
6.9
MT.3
23.5
154.1 292.1
285
7.1
MT.3
24.0
159.2 292.2
285
7.2
MT.3
24.5
159.4 292.4
285
7.4
MT.3
25.0
159.5 292.5
285
7.5
MT.3
25.5
163.7 292.7
285
7.7
MT.3
26.0
163.8 292.8
285
7.8
MT.3
26.5
164.0 298.0
290
8.0
MT.3
27.0
169.1 298.1
290
8.1
MT.3
27.5
169.3 303.3
295
8.3
MT.3
28.0
169.4 303.4
295
8.4
MT.3
28.5
173.6 308.6
300
8.6
MT.3
29.0
173.7 308.7
300
8.7
MT.3
29.5
173.9 313.9
305
8.9
MT.3
30.0
174.0 314.0
305
9.0
MT.3
30.5
179.2 319.2
310
9.2
MT.3
31.0
179.3 319.3
310
9.3
MT.3
31.5
179.5 324.5
315
9.5
MT.3
32.0
183.6 324.6
315
9.6
MT.3
33.0
183.9 354.9
345
9.9
MT.4
34.0
189.2 360.2
350
10.2
MT.4
35.0
189.5 360.5
350
10.5
MT.4
36.0
193.8 365.8
355
10.8
MT.4
37.0
194.1 366.1
355
11.1
MT.4
38.0
198.4 371.4
360
11.4
MT.4
39.0
40.0
198.7 371.7
199.0 377.0
360
365
11.7
12.0
MT.4
MT.4

CUTTING CONDITIONS
N198
TD
Taper shank
P
Steel
118
HSS
Thinning
HSS
DC>40
DC=3 3<DC < 6 6<DC < 10 10<DC < 1818<DC < 3030<DC < 5050<DC < 75
0
0.014
0
0.018
0
0.022
PL
0
0.027
0
0.033
0
0.039
0
0.046
DC
LF
CZC
LCF
OAL
a For general drilling.
DC
LCF
OAL
LF
PL
CZC
TDD0300M1
TDD0310M1
TDD0320M1
TDD0330M1
TDD0340M1
TDD0350M1
TDD0360M1
TDD0370M1
TDD0380M1
TDD0390M1
TDD0400M1
TDD0410M1
TDD0420M1
TDD0430M1
TDD0440M1
TDD0450M1
TDD0460M1
TDD0470M1
TDD0480M1
TDD0490M1
TDD0500M1
TDD0510M1
TDD0520M1
TDD0530M1
TDD0540M1
TDD0550M1
TDD0560M1
TDD0570M1
TDD0580M1
TDD0590M1
TDD0600M1
TDD0610M1
TDD0620M1
TDD0630M1
TDD0640M1
TDD0650M1
TDD0660M1
TDD0670M1
TDD0680M1
TDD0690M1
3.0
3.1
38.9
45.9
115.9
122.9
115
122
0.9
0.9
MT.1
MT.1
3.2
46.0
123.0
122
1.0
MT.1
3.3
46.0
123.0
122
1.0
MT.1
3.4
46.0
123.0
122
1.0
MT.1
3.5
46.1
123.1
122
1.1
MT.1
3.6
51.1
129.1
128
1.1
MT.1
3.7
51.1
129.1
128
1.1
MT.1
3.8
51.1
129.1
128
1.1
MT.1
3.9
51.2
129.2
128
1.2
MT.1
4.0
51.2
129.2
128
1.2
MT.1
4.1
56.2
136.2
135
1.2
MT.1
4.2
56.3
136.3
135
1.3
MT.1
4.3
56.3
136.3
135
1.3
MT.1
4.4
56.3
136.3
135
1.3
MT.1
4.5
56.4
136.4
135
1.4
MT.1
4.6
61.4
141.4
140
1.4
MT.1
4.7
61.4
141.4
140
1.4
MT.1
4.8
61.4
141.4
140
1.4
MT.1
4.9
61.5
141.5
140
1.5
MT.1
5.0
61.5
141.5
140
1.5
MT.1
5.1
66.5
146.5
145
1.5
MT.1
5.2
66.6
146.6
145
1.6
MT.1
5.3
66.6
146.6
145
1.6
MT.1
5.4
66.6
146.6
145
1.6
MT.1
5.5
66.7
146.7
145
1.7
MT.1
5.6
69.7
149.7
148
1.7
MT.1
5.7
69.7
149.7
148
1.7
MT.1
5.8
69.7
149.7
148
1.7
MT.1
5.9
69.8
149.8
148
1.8
MT.1
6.0
69.8
149.8
148
1.8
MT.1
6.1
73.8
153.8
152
1.8
MT.1
6.2
73.9
153.9
152
1.9
MT.1
6.3
73.9
153.9
152
1.9
MT.1
6.4
73.9
153.9
152
1.9
MT.1
6.5
74.0
154.0
152
2.0
MT.1
6.6
77.0
157.0
155
2.0
MT.1
6.7
77.0
157.0
155
2.0
MT.1
6.8
6.9
77.0
77.1
157.0
157.1
155
155
2.0
2.1
MT.1
MT.1
Order Number
DC
LCF
OAL
LF
PL
CZC
TDD0700M1
TDD0710M1
TDD0720M1
TDD0730M1
TDD0740M1
TDD0750M1
TDD0760M1
TDD0770M1
TDD0780M1
TDD0790M1
TDD0800M1
TDD0810M1
TDD0820M1
TDD0830M1
TDD0840M1
TDD0850M1
TDD0860M1
TDD0870M1
TDD0880M1
TDD0890M1
TDD0900M1
TDD0910M1
TDD0920M1
TDD0930M1
TDD0940M1
TDD0950M1
TDD0960M1
TDD0970M1
TDD0980M1
TDD0990M1
TDD1000M1
TDD1010M1
TDD1020M1
TDD1030M1
TDD1040M1
TDD1050M1
TDD1060M1
TDD1070M1
TDD1080M1
TDD1090M1
7.0
7.1
77.1
80.1
157.1
160.1
155
158
2.1
2.1
MT.1
MT.1
7.2
80.2
160.2
158
2.2
MT.1
7.3
80.2
160.2
158
2.2
MT.1
7.4
80.2
160.2
158
2.2
MT.1
7.5
80.3
160.3
158
2.3
MT.1
7.6
84.3
164.3
162
2.3
MT.1
7.7
84.3
164.3
162
2.3
MT.1
7.8
84.3
164.3
162
2.3
MT.1
7.9
84.4
164.4
162
2.4
MT.1
8.0
84.4
164.4
162
2.4
MT.1
8.1
87.4
170.4
168
2.4
MT.1
8.2
87.5
170.5
168
2.5
MT.1
8.3
87.5
170.5
168
2.5
MT.1
8.4
87.5
170.5
168
2.5
MT.1
8.5
87.6
170.6
168
2.6
MT.1
8.6
90.6
174.6
172
2.6
MT.1
8.7
90.6
174.6
172
2.6
MT.1
8.8
90.6
174.6
172
2.6
MT.1
8.9
90.7
174.7
172
2.7
MT.1
9.0
90.7
174.7
172
2.7
MT.1
9.1
94.7
177.7
175
2.7
MT.1
9.2
94.8
177.8
175
2.8
MT.1
9.3
94.8
177.8
175
2.8
MT.1
9.4
94.8
177.8
175
2.8
MT.1
9.5
94.9
177.9
175
2.9
MT.1
9.6
97.9
180.9
178
2.9
MT.1
9.7
97.9
180.9
178
2.9
MT.1
9.8
97.9
180.9
178
2.9
MT.1
9.9
98.0
181.0
178
3.0
MT.1
10.0
98.0
181.0
178
3.0
MT.1
10.1
101.0
185.0
182
3.0
MT.1
10.2
101.1
185.1
182
3.1
MT.1
10.3
101.1
185.1
182
3.1
MT.1
10.4
101.1
185.1
182
3.1
MT.1
10.5
101.2
185.2
182
3.2
MT.1
10.6
105.2
188.2
185
3.2
MT.1
10.7
105.2
188.2
185
3.2
MT.1
10.8
10.9
105.2
105.3
188.2
188.3
185
185
3.2
3.3
MT.1
MT.1
CUTTING CONDITIONS
DRILLING
Order Number
Stock
Stock
Unit : mm
N199
N185
TAPER SHANK DRILLS

HSS
TD
Taper shank
DRILLING
DC
LCF
OAL
LF
PL
CZC
TDD1100M1
TDD1110M1
TDD1120M1
TDD1130M1
TDD1140M1
TDD1150M1
TDD1160M1
TDD1170M1
TDD1180M1
TDD1190M1
TDD1200M1
TDD1210M1
TDD1220M1
TDD1230M1
TDD1240M1
TDD1250M1
TDD1260M1
TDD1270M1
TDD1280M1
TDD1290M1
TDD1300M1
TDD1310M1
TDD1320M1
TDD1330M1
TDD1340M1
TDD1350M1
TDD1360M1
TDD1370M1
TDD1380M1
TDD1390M1
TDD1400M1
TDD1410M2
TDD1420M2
TDD1430M2
TDD1440M2
TDD1450M2
TDD1460M2
TDD1470M2
TDD1480M2
TDD1490M2
TDD1500M2
TDD1510M2
TDD1520M2
TDD1530M2
TDD1540M2
TDD1550M2
TDD1560M2
TDD1570M2
TDD1580M2
TDD1590M2
11.0
11.1
105.3 188.3
108.3 191.3
185
188
3.3
3.3
MT.1
MT.1
11.2
108.4 191.4
188
3.4
MT.1
11.3
108.4 191.4
188
3.4
MT.1
11.4
108.4 191.4
188
3.4
MT.1
11.5
108.5 191.5
188
3.5
MT.1
11.6
111.5
195.5
192
3.5
MT.1
11.7
111.5
195.5
192
3.5
MT.1
11.8
111.5
195.5
192
3.5
MT.1
11.9
111.6
195.6
192
3.6
MT.1
12.0
111.6
195.6
192
3.6
MT.1
12.1
115.6
198.6
195
3.6
MT.1
12.2
115.7
198.7
195
3.7
MT.1
12.3
115.7
198.7
195
3.7
MT.1
12.4
115.7
198.7
195
3.7
MT.1
12.5
115.8
198.8
195
3.8
MT.1
12.6
118.8
201.8
198
3.8
MT.1
12.7
118.8
201.8
198
3.8
MT.1
12.8
118.8
201.8
198
3.8
MT.1
12.9
118.9
201.9
198
3.9
MT.1
13.0
118.9
201.9
198
3.9
MT.1
13.1
121.9 205.9
202
3.9
MT.1
13.2
122.0 206.0
202
4.0
MT.1
13.3
122.0 206.0
202
4.0
MT.1
13.4
122.0 206.0
202
4.0
MT.1
13.5
122.1 206.1
202
4.1
MT.1
13.6
126.1 209.1
205
4.1
MT.1
13.7
126.1 209.1
205
4.1
MT.1
13.8
126.1 209.1
205
4.1
MT.1
13.9
126.2 209.2
205
4.2
MT.1
14.0
126.2 209.2
205
4.2
MT.1
14.1
126.2 226.2
222
4.2
MT.2
14.2
126.3 226.3
222
4.3
MT.2
14.3
126.3 226.3
222
4.3
MT.2
14.4
126.3 226.3
222
4.3
MT.2
14.5
126.4 226.4
222
4.4
MT.2
14.6
129.4 229.4
225
4.4
MT.2
14.7
129.4 229.4
225
4.4
MT.2
14.8
129.4 229.4
225
4.4
MT.2
14.9
129.5 229.5
225
4.5
MT.2
15.0
129.5 229.5
225
4.5
MT.2
15.1
132.5 232.5
228
4.5
MT.2
15.2
132.6 232.6
228
4.6
MT.2
15.3
132.6 232.6
228
4.6
MT.2
15.4
132.6 232.6
228
4.6
MT.2
15.5
132.7 232.7
228
4.7
MT.2
15.6
134.7 234.7
230
4.7
MT.2
15.7
134.7 234.7
230
4.7
MT.2
15.8
15.9
134.7 234.7
134.8 234.8
230
230
4.7
4.8
MT.2
MT.2
Stock
Order Number
N186
Stock
Unit : mm
Order Number
DC
LCF
OAL
LF
PL
CZC
TDD1600M2
TDD1610M2
TDD1620M2
TDD1630M2
TDD1640M2
TDD1650M2
TDD1660M2
TDD1670M2
TDD1680M2
TDD1690M2
TDD1700M2
TDD1710M2
TDD1720M2
TDD1730M2
TDD1740M2
TDD1750M2
TDD1760M2
TDD1770M2
TDD1780M2
TDD1790M2
TDD1800M2
TDD1810M2
TDD1820M2
TDD1830M2
TDD1840M2
TDD1850M2
TDD1860M2
TDD1870M2
TDD1880M2
TDD1890M2
TDD1900M2
TDD1910M2
TDD1920M2
TDD1930M2
TDD1940M2
TDD1950M2
TDD1960M2
TDD1970M2
TDD1980M2
TDD1990M2
TDD2000M2
TDD2010M2
TDD2020M2
TDD2030M2
TDD2040M2
TDD2050M2
TDD2060M2
TDD2070M2
TDD2080M2
TDD2090M2
16.0
16.1
134.8 234.8
136.8 236.8
230
232
4.8
4.8
MT.2
MT.2
16.2
136.9 236.9
232
4.9
MT.2
16.3
136.9 236.9
232
4.9
MT.2
16.4
136.9 236.9
232
4.9
MT.2
16.5
137.0 237.0
232
5.0
MT.2
16.6
140.0 240.0
235
5.0
MT.2
16.7
140.0 240.0
235
5.0
MT.2
16.8
140.0 240.0
235
5.0
MT.2
16.9
140.1 240.1
235
5.1
MT.2
17.0
140.1 240.1
235
5.1
MT.2
17.1
145.1 245.1
240
5.1
MT.2
17.2
145.2 245.2
240
5.2
MT.2
17.3
145.2 245.2
240
5.2
MT.2
17.4
145.2 245.2
240
5.2
MT.2
17.5
145.3 245.3
240
5.3
MT.2
17.6
145.3 245.3
240
5.3
MT.2
17.7
145.3 245.3
240
5.3
MT.2
17.8
145.3 245.3
240
5.3
MT.2
17.9
145.4 245.4
240
5.4
MT.2
18.0
145.4 245.4
240
5.4
MT.2
18.1
150.4 250.4
245
5.4
MT.2
18.2
150.5 250.5
245
5.5
MT.2
18.3
150.5 250.5
245
5.5
MT.2
18.4
150.5 250.5
245
5.5
MT.2
18.5
150.6 250.6
245
5.6
MT.2
18.6
150.6 250.6
245
5.6
MT.2
18.7
150.6 250.6
245
5.6
MT.2
18.8
150.6 250.6
245
5.6
MT.2
18.9
150.7 250.7
245
5.7
MT.2
19.0
150.7 250.7
245
5.7
MT.2
19.1
155.7 255.7
250
5.7
MT.2
19.2
155.8 255.8
250
5.8
MT.2
19.3
155.8 255.8
250
5.8
MT.2
19.4
155.8 255.8
250
5.8
MT.2
19.5
155.9 255.9
250
5.9
MT.2
19.6
155.9 255.9
250
5.9
MT.2
19.7
155.9 255.9
250
5.9
MT.2
19.8
155.9 255.9
250
5.9
MT.2
19.9
156.0 256.0
250
6.0
MT.2
20.0
156.0 256.0
250
6.0
MT.2
20.1
161.0 261.0
255
6.0
MT.2
20.2
161.1 261.1
255
6.1
MT.2
20.3
161.1 261.1
255
6.1
MT.2
20.4
161.1 261.1
255
6.1
MT.2
20.5
161.2 261.2
255
6.2
MT.2
20.6
161.2 261.2
255
6.2
MT.2
20.7
161.2 261.2
255
6.2
MT.2
20.8
20.9
161.2 261.2
161.3 261.3
255
255
6.2
6.3
MT.2
MT.2
HSS
DC
LCF
OAL
LF
PL
CZC
TDD2100M2
TDD2110M2
TDD2120M2
TDD2130M2
TDD2140M2
TDD2150M2
TDD2160M2
TDD2170M2
TDD2180M2
TDD2190M2
TDD2200M2
TDD2210M2
TDD2220M2
TDD2230M2
TDD2240M2
TDD2250M2
TDD2260M2
TDD2270M2
TDD2280M2
TDD2290M2
TDD2300M2
TDD2310M3
TDD2320M3
TDD2330M3
TDD2340M3
TDD2350M3
TDD2360M3
TDD2370M3
TDD2380M3
TDD2390M3
TDD2400M3
TDD2410M3
TDD2420M3
TDD2430M3
TDD2440M3
TDD2450M3
TDD2460M3
TDD2470M3
TDD2480M3
TDD2490M3
TDD2500M3
TDD2510M3
TDD2520M3
TDD2530M3
TDD2540M3
TDD2550M3
TDD2560M3
TDD2570M3
TDD2580M3
TDD2590M3
21.0
21.1
161.3 261.3
166.3 266.3
255
260
6.3
6.3
MT.2
MT.2
21.2
166.4 266.4
260
6.4
MT.2
21.3
166.4 266.4
260
6.4
MT.2
21.4
166.4 266.4
260
6.4
MT.2
21.5
166.5 266.5
260
6.5
MT.2
21.6
166.5 266.5
260
6.5
MT.2
21.7
166.5 266.5
260
6.5
MT.2
21.8
166.5 266.5
260
6.5
MT.2
21.9
166.6 266.6
260
6.6
MT.2
22.0
166.6 266.6
260
6.6
MT.2
22.1
171.6 271.6
265
6.6
MT.2
22.2
171.7 271.7
265
6.7
MT.2
22.3
171.7 271.7
265
6.7
MT.2
22.4
171.7 271.7
265
6.7
MT.2
22.5
171.8 271.8
265
6.8
MT.2
22.6
171.8 271.8
265
6.8
MT.2
22.7
171.8 271.8
265
6.8
MT.2
22.8
171.8 271.8
265
6.8
MT.2
22.9
171.9 271.9
265
6.9
MT.2
23.0
171.9 271.9
265
6.9
MT.2
23.1
171.9 291.9
285
6.9
MT.3
23.2
172.0 292.0
285
7.0
MT.3
23.3
172.0 292.0
285
7.0
MT.3
23.4
172.0 292.0
285
7.0
MT.3
23.5
172.1 292.1
285
7.1
MT.3
23.6
172.1 292.1
285
7.1
MT.3
23.7
172.1 292.1
285
7.1
MT.3
23.8
172.2 292.2
285
7.2
MT.3
23.9
172.2 292.2
285
7.2
MT.3
24.0
172.2 292.2
285
7.2
MT.3
24.1
172.2 292.2
285
7.2
MT.3
24.2
172.3 292.3
285
7.3
MT.3
24.3
172.3 292.3
285
7.3
MT.3
24.4
172.3 292.3
285
7.3
MT.3
24.5
172.4 292.4
285
7.4
MT.3
24.6
172.4 292.4
285
7.4
MT.3
24.7
172.4 292.4
285
7.4
MT.3
24.8
172.5 292.5
285
7.5
MT.3
24.9
172.5 292.5
285
7.5
MT.3
25.0
172.5 292.5
285
7.5
MT.3
25.1
172.5 292.5
285
7.5
MT.3
25.2
172.6 292.6
285
7.6
MT.3
25.3
172.6 292.6
285
7.6
MT.3
25.4
172.6 292.6
285
7.6
MT.3
25.5
172.7 292.7
285
7.7
MT.3
25.6
172.7 292.7
285
7.7
MT.3
25.7
172.7 292.7
285
7.7
MT.3
25.8
25.9
172.8 292.8
172.8 292.8
285
285
7.8
7.8
MT.3
MT.3
Order Number
DC
LCF
OAL
LF
PL
CZC
TDD2600M3
TDD2610M3
TDD2620M3
TDD2630M3
TDD2640M3
TDD2650M3
TDD2660M3
TDD2670M3
TDD2680M3
TDD2690M3
TDD2700M3
TDD2710M3
TDD2720M3
TDD2730M3
TDD2740M3
TDD2750M3
TDD2760M3
TDD2770M3
TDD2780M3
TDD2790M3
TDD2800M3
TDD2810M3
TDD2820M3
TDD2830M3
TDD2840M3
TDD2850M3
TDD2860M3
TDD2870M3
TDD2880M3
TDD2890M3
TDD2900M3
TDD2910M3
TDD2920M3
TDD2930M3
TDD2940M3
TDD2950M3
TDD2960M3
TDD2970M3
TDD2980M3
TDD2990M3
TDD3000M3
TDD3010M3
TDD3020M3
TDD3030M3
TDD3040M3
TDD3050M3
TDD3060M3
TDD3070M3
TDD3080M3
TDD3090M3
26.0
26.1
172.8 292.8
177.8 297.8
285
290
7.8
7.8
MT.3
MT.3
26.2
177.9 297.9
290
7.9
MT.3
26.3
177.9 297.9
290
7.9
MT.3
26.4
177.9 297.9
290
7.9
MT.3
26.5
178.0 298.0
290
8.0
MT.3
26.6
178.0 298.0
290
8.0
MT.3
26.7
178.0 298.0
290
8.0
MT.3
26.8
178.1 298.1
290
8.1
MT.3
26.9
178.1 298.1
290
8.1
MT.3
27.0
178.1 298.1
290
8.1
MT.3
27.1
183.1 303.1
295
8.1
MT.3
27.2
183.2 303.2
295
8.2
MT.3
27.3
183.2 303.2
295
8.2
MT.3
27.4
183.2 303.2
295
8.2
MT.3
27.5
183.3 303.3
295
8.3
MT.3
27.6
183.3 303.3
295
8.3
MT.3
27.7
183.3 303.3
295
8.3
MT.3
27.8
183.4 303.4
295
8.4
MT.3
27.9
183.4 303.4
295
8.4
MT.3
28.0
183.4 303.4
295
8.4
MT.3
28.1
188.4 308.4
300
8.4
MT.3
28.2
188.5 308.5
300
8.5
MT.3
28.3
188.5 308.5
300
8.5
MT.3
28.4
188.5 308.5
300
8.5
MT.3
28.5
188.6 308.6
300
8.6
MT.3
28.6
188.6 308.6
300
8.6
MT.3
28.7
188.6 308.6
300
8.6
MT.3
28.8
188.7 308.7
300
8.7
MT.3
28.9
188.7 308.7
300
8.7
MT.3
29.0
188.7 308.7
300
8.7
MT.3
29.1
193.7 313.7
305
8.7
MT.3
29.2
193.8 313.8
305
8.8
MT.3
29.3
193.8 313.8
305
8.8
MT.3
29.4
193.8 313.8
305
8.8
MT.3
29.5
193.9 313.9
305
8.9
MT.3
29.6
193.9 313.9
305
8.9
MT.3
29.7
193.9 313.9
305
8.9
MT.3
29.8
194.0 314.0
305
9.0
MT.3
29.9
194.0 314.0
305
9.0
MT.3
30.0
194.0 314.0
305
9.0
MT.3
30.1
199.0 319.0
310
9.0
MT.3
30.2
199.1 319.1
310
9.1
MT.3
30.3
199.1 319.1
310
9.1
MT.3
30.4
199.1 319.1
310
9.1
MT.3
30.5
199.2 319.2
310
9.2
MT.3
30.6
199.2 319.2
310
9.2
MT.3
30.7
199.2 319.2
310
9.2
MT.3
30.8
30.9
199.3 319.3
199.3 319.3
310
310
9.3
9.3
MT.3
MT.3
CUTTING CONDITIONS
DRILLING
Order Number
Stock
Stock
Unit : mm
N199
N187
TAPER SHANK DRILLS

HSS
TD
Taper shank
DRILLING
DC
LCF
OAL
LF
PL
CZC
TDD3100M3
TDD3110M3
TDD3120M3
TDD3130M3
TDD3140M3
TDD3150M3
TDD3160M3
TDD3170M3
TDD3180M3
TDD3190M3
TDD3200M3
TDD3250M4
TDD3300M4
TDD3350M4
TDD3400M4
TDD3450M4
TDD3500M4
TDD3550M4
TDD3600M4
TDD3650M4
TDD3700M4
TDD3750M4
TDD3800M4
TDD3850M4
TDD3900M4
TDD3950M4
TDD4000M4
TDD4050M4
TDD4100M4
TDD4150M4
TDD4200M4
TDD4250M4
TDD4300M4
TDD4350M4
TDD4400M4
TDD4450M4
TDD4500M4
TDD4550M4
TDD4600M4
TDD4650M4
TDD4700M4
TDD4750M4
TDD4800M4
TDD4850M4
TDD4900M4
TDD4950M4
TDD5000M4
TDD5100M5
TDD5200M5
TDD5300M5
31.0
31.1
199.3 319.3
204.3 324.3
310
315
9.3
9.3
MT.3
MT.3
31.2
204.4 324.4
315
9.4
MT.3
31.3
204.4 324.4
315
9.4
MT.3
31.4
204.4 324.4
315
9.4
MT.3
31.5
204.5 324.5
315
9.5
MT.3
31.6
204.5 324.5
315
9.5
MT.3
31.7
204.5 324.5
315
9.5
MT.3
31.8
204.6 324.6
315
9.6
MT.3
31.9
204.6 324.6
315
9.6
MT.3
32.0
204.6 324.6
315
9.6
MT.3
32.5
209.8 354.8
345
9.8
MT.4
33.0
209.9 354.9
345
9.9
MT.4
33.5
215.1 360.1
350
10.1
MT.4
34.0
215.2 360.2
350
10.2
MT.4
34.5
215.4 360.4
350
10.4
MT.4
35.0
215.5 360.5
350
10.5
MT.4
35.5
220.7 365.7
355
10.7
MT.4
36.0
220.8 365.8
355
10.8
MT.4
36.5
221.0 366.0
355
11.0
MT.4
37.0
221.1 366.1
355
11.1
MT.4
37.5
226.3 371.3
360
11.3
MT.4
38.0
226.4 371.4
360
11.4
MT.4
38.5
226.6 371.6
360
11.6
MT.4
39.0
226.7 371.7
360
11.7
MT.4
39.5
231.9 376.9
365
11.9
MT.4
40.0
232.0 377.0
365
12.0
MT.4
40.5
232.2 377.2
365
12.2
MT.4
41.0
232.3 377.3
365
12.3
MT.4
41.5
237.5 382.5
370
12.5
MT.4
42.0
237.6 382.6
370
12.6
MT.4
42.5
237.8 382.8
370
12.8
MT.4
43.0
237.9 382.9
370
12.9
MT.4
43.5
243.1 388.1
375
13.1
MT.4
44.0
243.2 388.2
375
13.2
MT.4
44.5
243.4 388.4
375
13.4
MT.4
45.0
243.5 388.5
375
13.5
MT.4
45.5
248.7 393.7
380
13.7
MT.4
46.0
248.8 393.8
380
13.8
MT.4
46.5
249.0 394.0
380
14.0
MT.4
47.0
249.1 394.1
380
14.1
MT.4
47.5
254.3 399.3
385
14.3
MT.4
48.0
254.4 399.4
385
14.4
MT.4
48.5
254.6 399.6
385
14.6
MT.4
49.0
254.7 399.7
385
14.7
MT.4
49.5
259.9 404.9
390
14.9
MT.4
50.0
260.0 405.0
390
15.0
MT.4
51.0
260.3 440.3
425
15.3
MT.5
52.0
53.0
265.6 445.6
265.9 445.9
430
430
15.6
15.9
MT.5
MT.5
Stock
Order Number
N188
Stock
Unit : mm
Order Number
DC
LCF
OAL
LF
PL
CZC
TDD5400M5
TDD5500M5
TDD5600M5
TDD5700M5
TDD5800M5
TDD5900M5
TDD6000M5
TDD6100M5
TDD6200M5
TDD6300M5
TDD6400M5
TDD6500M5
TDD6600M5
TDD6700M5
TDD6800M5
TDD6900M5
TDD7000M5
TDD7100M5
TDD7200M5
TDD7300M5
TDD7400M5
TDD7500M5
54.0
55.0
271.2 451.2
271.5 451.5
435
435
16.2
16.5
MT.5
MT.5
56.0
276.8 456.8
440
16.8
MT.5
57.0
277.1 457.1
440
17.1
MT.5
58.0
282.4 462.4
445
17.4
MT.5
59.0
282.7 462.7
445
17.7
MT.5
60.0
288.0 468.0
450
18.0
MT.5
61.0
288.3 468.3
450
18.3
MT.5
62.0
293.6 473.6
455
18.6
MT.5
63.0
293.9 473.9
455
18.9
MT.5
64.0
299.2 479.2
460
19.2
MT.5
65.0
299.5 479.5
460
19.5
MT.5
66.0
304.8 484.8
465
19.8
MT.5
67.0
305.1 485.1
465
20.1
MT.5
68.0
310.4 490.4
470
20.4
MT.5
69.0
310.7 490.7
470
20.7
MT.5
70.0
316.0 496.0
475
21.0
MT.5
71.0
316.3 496.3
475
21.3
MT.5
72.0
321.6 501.6
480
21.6
MT.5
73.0
321.9 501.9
480
21.9
MT.5
74.0
75.0
327.2 507.2
327.5 507.5
485
485
22.2
22.5
MT.5
MT.5

CUTTING CONDITIONS
N199
KTD
Cobalt HSS
P
Steel
118
CO HSS
128
DC<10,DC>35 10<DC<35
Thinning
Thinning
16<DC<35
DC>35
HSS
5 < DC < 6 6<DC < 10 10<DC < 1818<DC < 3030<DC < 50
0
0.018
0
0.022
0
0.027
PL
0
0.033
0
0.039
DC
LF
CZC
LCF
OAL
a Suitable for drilling of difficult-to-cut materials.
DC
LCF
OAL
LF
PL
CZC
KTDD0500M1
KTDD0550M1
KTDD0600M1
KTDD0650M1
KTDD0700M1
KTDD0750M1
KTDD0800M1
KTDD0850M1
KTDD0900M1
KTDD0950M1
KTDD1000M1
KTDD1010M1
KTDD1020M1
KTDD1030M1
KTDD1040M1
KTDD1050M1
KTDD1060M1
KTDD1070M1
KTDD1080M1
KTDD1090M1
KTDD1100M1
KTDD1150M1
KTDD1200M1
KTDD1210M2
KTDD1220M2
KTDD1250M2
KTDD1300M2
KTDD1310M2
KTDD1320M2
KTDD1350M2
KTDD1370M2
KTDD1380M2
KTDD1390M2
KTDD1400M2
KTDD1410M2
KTDD1420M2
KTDD1430M2
KTDD1440M2
KTDD1450M2
KTDD1470M2
5.0
5.5
61.5
66.7
141.5
146.7
140
145
1.5
1.7
MT.1
MT.1
6.0
69.8
149.8
148
1.8
MT.1
6.5
74.0
154.0
152
2.0
MT.1
7.0
77.1
157.1
155
2.1
MT.1
7.5
80.3
160.3
158
2.3
MT.1
8.0
84.4
164.4
162
2.4
MT.1
8.5
87.6
170.6
168
2.6
MT.1
9.0
90.7
174.7
172
2.7
MT.1
9.5
94.9
177.9
175
2.9
MT.1
10.0
97.4
180.4
178
2.4
MT.1
10.1
100.5
184.5
182
2.5
MT.1
10.2
100.5
184.5
182
2.5
MT.1
10.3
100.5
184.5
182
2.5
MT.1
10.4
100.5
184.5
182
2.5
MT.1
10.5
100.6
184.6
182
2.6
MT.1
10.6
104.6
187.6
185
2.6
MT.1
10.7
104.6
187.6
185
2.6
MT.1
10.8
104.6
187.6
185
2.6
MT.1
10.9
104.7
187.7
185
2.7
MT.1
11.0
104.7
187.7
185
2.7
MT.1
11.5
107.8
190.8
188
2.8
MT.1
12.0
110.9
194.9
192
2.9
MT.1
12.1
115.0
215.0
212
3.0
MT.2
12.2
115.0
215.0
212
3.0
MT.2
12.5
115.0
215.0
212
3.0
MT.2
13.0
118.2
218.2
215
3.2
MT.2
13.1
121.2
221.2
218
3.2
MT.2
13.2
121.2
221.2
218
3.2
MT.2
13.5
121.3
221.3
218
3.3
MT.2
13.7
125.3
225.3
222
3.3
MT.2
13.8
125.4
225.4
222
3.4
MT.2
13.9
125.4
225.4
222
3.4
MT.2
14.0
125.4
225.4
222
3.4
MT.2
14.1
125.4
225.4
222
3.4
MT.2
14.2
125.5
225.5
222
3.5
MT.2
14.3
125.5
225.5
222
3.5
MT.2
14.4
125.5
225.5
222
3.5
MT.2
14.5
14.7
125.5
128.6
225.5
228.6
222
225
3.5
3.6
MT.2
MT.2
a
a
Order Number
DC
LCF
OAL
LF
PL
CZC
KTDD1500M2
KTDD1550M2
KTDD1600M2
KTDD1620M2
KTDD1650M2
KTDD1670M2
KTDD1700M2
KTDD1750M2
KTDD1770M2
KTDD1800M2
KTDD1850M2
KTDD1900M2
KTDD1950M2
KTDD2000M2
KTDD2050M3
KTDD2100M3
KTDD2150M3
KTDD2200M3
KTDD2250M3
KTDD2300M3
KTDD2350M3
KTDD2400M3
KTDD2450M3
KTDD2500M3
KTDD2550M3
KTDD2600M3
KTDD2650M3
KTDD2700M3
KTDD2750M4
KTDD2800M4
KTDD2850M4
KTDD2900M4
KTDD2950M4
KTDD3000M4
KTDD3050M4
KTDD3100M4
KTDD3150M4
KTDD3200M4
KTDD3300M4
KTDD3400M4
15.0
15.5
128.7 228.7
131.8 231.8
225
228
3.7
3.8
MT.2
MT.2
16.0
133.9 233.9
230
3.9
MT.2
16.2
136.0 236.0
232
4.0
MT.2
16.5
136.0 236.0
232
4.0
MT.2
16.7
139.1 239.1
235
4.1
MT.2
17.0
139.1 239.1
235
4.1
MT.2
17.5
144.3 244.3
240
4.3
MT.2
17.7
144.3 244.3
240
4.3
MT.2
18.0
144.4 244.4
240
4.4
MT.2
18.5
149.5 249.5
245
4.5
MT.2
19.0
149.6 249.6
245
4.6
MT.2
19.5
154.8 254.8
250
4.8
MT.2
20.0
154.9 254.9
250
4.9
MT.2
20.5
160.0 280.0
275
5.0
MT.3
21.0
160.1 280.1
275
5.1
MT.3
21.5
165.2 285.2
280
5.2
MT.3
22.0
165.4 285.4
280
5.4
MT.3
22.5
170.5 290.5
285
5.5
MT.3
23.0
170.6 290.6
285
5.6
MT.3
23.5
170.7 290.7
285
5.7
MT.3
24.0
170.9 290.9
285
5.9
MT.3
24.5
171.0 291.0
285
6.0
MT.3
25.0
171.1 291.1
285
6.1
MT.3
25.5
171.2 291.2
285
6.2
MT.3
26.0
171.3 291.3
285
6.3
MT.3
26.5
176.5 296.5
290
6.5
MT.3
27.0
176.6 296.6
290
6.6
MT.3
27.5
181.7 326.7
320
6.7
MT.4
28.0
181.8 326.8
320
6.8
MT.4
28.5
187.0 332.0
325
7.0
MT.4
29.0
187.1 332.1
325
7.1
MT.4
29.5
192.2 337.2
330
7.2
MT.4
30.0
192.3 337.3
330
7.3
MT.4
30.5
197.4 342.4
335
7.4
MT.4
31.0
197.6 342.6
335
7.6
MT.4
31.5
202.7 347.7
340
7.7
MT.4
32.0
202.8 347.8
340
7.8
MT.4
33.0
34.0
208.0 353.0
213.3 358.3
345
350
8.0
8.3
MT.4
MT.4
CUTTING CONDITIONS
DRILLING
Order Number
Stock
Stock
Unit : mm
N199
N189
TAPER SHANK DRILLS

HSS
KTD
Cobalt HSS
Stock
Unit : mm
Order Number
DC
LCF
OAL
LF
PL
CZC
KTDD3500M4
KTDD3600M4
KTDD3700M4
KTDD3800M4
KTDD3900M4
KTDD4000M4
KTDD4100M4
KTDD4200M4
KTDD4300M4
KTDD4400M4
KTDD4500M4
KTDD4600M4
KTDD4700M4
KTDD4800M4
KTDD4900M4
KTDD5000M4
35.0
36.0
213.5 358.5
220.8 365.8
350
355
8.5
10.8
MT.4
MT.4
37.0
221.1 366.1
355
11.1
MT.4
38.0
226.4 371.4
360
11.4
MT.4
39.0
226.7 371.7
360
11.7
MT.4
40.0
232.0 377.0
365
12.0
MT.4
41.0
232.3 377.3
365
12.3
MT.4
42.0
237.6 382.6
370
12.6
MT.4
43.0
237.9 382.9
370
12.9
MT.4
44.0
243.2 388.2
375
13.2
MT.4
45.0
243.5 388.5
375
13.5
MT.4
46.0
248.8 393.8
380
13.8
MT.4
47.0
249.1 394.1
380
14.1
MT.4
48.0
254.4 399.4
385
14.4
MT.4
49.0
50.0
254.7 399.7
260.0 405.0
385
390
14.7
15.0
MT.4
MT.4
DRILLING
N190

CUTTING CONDITIONS
N199
GWTS
TiN, For deep hole, Convolute flute
P
Steel
CO HSS
DC=6
0
0.018
118
Thinning
HSS
6<DC < 10 10<DC < 1818<DC < 3030<DC < 32

0
0.022
0
0.027
PL
0
0.033
0
0.039
DC
LF
CZC
LCF
OAL
a Suitable for general and deep hole drilling.
LCF
OAL
LF
PL
CZC
6.0
6.2
69.8 149.8 148

73.9 153.9 152
1.8
1.9
MT.1
MT.1
6.5
74.0 154.0 152
2.0
MT.1
6.8
77.0 157.0 155
2.0
MT.1
6.9
77.1 157.1 155
2.1
MT.1
7.0
77.1 157.1 155
2.1
MT.1
7.2
80.2 160.2 158
2.2
MT.1
7.5
80.3 160.3 158
2.3
MT.1
7.8
84.3 164.3 162
2.3
MT.1
8.0
84.4 164.4 162
2.4
MT.1
8.2
87.5 170.5 168
2.5
MT.1
8.5
87.6 170.6 168
2.6
MT.1
8.8
90.6 174.6 172
2.6
MT.1
9.0
90.7 174.7 172
2.7
MT.1
9.2
94.8 177.8 175
2.8
MT.1
9.5
94.9 177.9 175
2.9
MT.1
9.8
97.9 180.9 178
2.9
MT.1
10.0
98.0 181.0 178
3.0
MT.1
10.2 101.1 185.1 182
3.1
MT.1
10.3 101.1 185.1 182
3.1
MT.1
10.5 101.2 185.2 182
3.2
MT.1
11.0 105.3 188.3 185
3.3
MT.1
11.5 108.5 191.5 188
3.5
MT.1
12.0 111.6 195.6 192
3.6
MT.1
12.2 115.7 215.7 212
3.7
MT.2
12.3 115.7 215.7 212
3.7
MT.2
12.5 115.8 215.8 212
3.8
MT.2
13.0 118.9 218.9 215
3.9
MT.2
13.5 122.1 222.1 218
4.1
MT.2
14.0 126.2 226.2 222
4.2
MT.2
14.1 126.2 226.2 222
4.2
MT.2
14.2 126.3 226.3 222
4.3
MT.2
14.5 126.4 226.4 222
4.4
MT.2
15.0 129.5 229.5 225
4.5
MT.2
15.5 132.7 232.7 228
4.7
MT.2
16.0 134.8 234.8 230
4.8
MT.2
16.5 137.0 237.0 232
5.0
MT.2
17.0 140.1 240.1 235
5.1
MT.2
17.5 145.3 245.3 240

18.0 145.4 245.4 240
5.3
5.4
MT.2
MT.2
Order Number
GWTSD1850M2
GWTSD1900M2
GWTSD1950M2
GWTSD2000M2
GWTSD2100M3
GWTSD2200M3
GWTSD2300M3
GWTSD2400M3
GWTSD2500M3
GWTSD2600M3
GWTSD2700M3
GWTSD2800M4
GWTSD2900M4
GWTSD3000M4
GWTSD3100M4
GWTSD3200M4
DC
LCF
OAL
LF
PL
CZC
18.5 150.6 250.6 245

19.0 150.7 250.7 245
5.6
5.7
MT.2
MT.2
19.5 155.9 255.9 250
5.9
MT.2
20.0 156.0 256.0 250
6.0
MT.2
21.0 161.3 281.3 275
6.3
MT.3
22.0 166.6 286.6 280
6.6
MT.3
23.0 171.9 291.9 285
6.9
MT.3
24.0 172.2 292.2 285
7.2
MT.3
25.0 172.5 292.5 285
7.5
MT.3
26.0 172.8 292.8 285
7.8
MT.3
27.0 178.1 298.1 290
8.1
MT.3
28.0 183.4 328.4 320
8.4
MT.4
29.0 188.7 333.7 325
8.7
MT.4
30.0 194.0 339.0 330
9.0
MT.4
31.0 199.3 344.3 335

32.0 204.6 349.6 340
9.3
9.6
MT.4
MT.4
DRILLING
GWTSD0600M1
GWTSD0620M1
GWTSD0650M1
GWTSD0680M1
GWTSD0690M1
GWTSD0700M1
GWTSD0720M1
GWTSD0750M1
GWTSD0780M1
GWTSD0800M1
GWTSD0820M1
GWTSD0850M1
GWTSD0880M1
GWTSD0900M1
GWTSD0920M1
GWTSD0950M1
GWTSD0980M1
GWTSD1000M1
GWTSD1020M1
GWTSD1030M1
GWTSD1050M1
GWTSD1100M1
GWTSD1150M1
GWTSD1200M1
GWTSD1220M2
GWTSD1230M2
GWTSD1250M2
GWTSD1300M2
GWTSD1350M2
GWTSD1400M2
GWTSD1410M2
GWTSD1420M2
GWTSD1450M2
GWTSD1500M2
GWTSD1550M2
GWTSD1600M2
GWTSD1650M2
GWTSD1700M2
GWTSD1750M2
GWTSD1800M2
DC
Stock
Order Number
Stock
Unit : mm
CUTTING CONDITIONS
N198
N191
TAPER SHANK DRILLS

HSS
LTD
Extra long
P
Thinning
DC>6
Steel
118
HSS
DC=6
6<DC < 10 10<DC < 1818<DC < 3030<DC < 40
0
0.018
0
0.022
0
0.027
PL
0
0.033
0
0.039
DC
LF
CZC
LCF
OAL
a For deep hole drilling.
DRILLING
LTDD0600A200M1
LTDD0600A250M1
LTDD0600A300M1
LTDD0600A350M1
LTDD0650A250M1
LTDD0650A300M1
LTDD0650A350M1
LTDD0700A250M1
LTDD0700A300M1
LTDD0700A350M1
LTDD0750A250M1
LTDD0750A300M1
LTDD0750A350M1
LTDD0800A250M1
LTDD0800A300M1
LTDD0800A350M1
LTDD0850A250M1
LTDD0850A300M1
LTDD0850A350M1
LTDD0900A250M1
LTDD0900A300M1
LTDD0900A350M1
LTDD0950A250M1
LTDD0950A300M1
LTDD0950A350M1
LTDD0950A400M1
LTDD1000A250M1
LTDD1000A300M1
LTDD1000A350M1
LTDD1000A400M1
LTDD1050A250M1
LTDD1050A300M1
LTDD1050A350M1
LTDD1050A400M1
LTDD1100A250M1
LTDD1100A300M1
LTDD1100A350M1
LTDD1100A400M1
LTDD1150A250M1
LTDD1150A300M1
N192
DC
LCF OAL
LF
PL
CZC
6.0 101.8 201.8 200

6.0 151.8 251.8 250
1.8
1.8
MT.1
MT.1
6.0 201.8 301.8 300
1.8
MT.1
6.0 226.8 351.8 350
1.8
MT.1
6.5 152.0 252.0 250
2.0
MT.1
6.5 202.0 302.0 300
2.0
MT.1
6.5 227.0 352.0 350
2.0
MT.1
7.0 152.1 252.1 250
2.1
MT.1
7.0 202.1 302.1 300
2.1
MT.1
7.0 227.1 352.1 350
2.1
MT.1
7.5 152.3 252.3 250
2.3
MT.1
7.5 202.3 302.3 300
2.3
MT.1
7.5 227.3 352.3 350
2.3
MT.1
8.0 152.4 252.4 250
2.4
MT.1
8.0 202.4 302.4 300
2.4
MT.1
8.0 227.4 352.4 350
2.4
MT.1
8.5 152.6 252.6 250
2.6
MT.1
8.5 202.6 302.6 300
2.6
MT.1
8.5 227.6 352.6 350
2.6
MT.1
9.0 152.7 252.7 250
2.7
MT.1
9.0 202.7 302.7 300
2.7
MT.1
9.0 227.7 352.7 350
2.7
MT.1
9.5 152.9 252.9 250
2.9
MT.1
9.5 202.9 302.9 300
2.9
MT.1
9.5 227.9 352.9 350
2.9
MT.1
9.5 252.9 402.9 400
2.9
MT.1
10.0 153.0 253.0 250
3.0
MT.1
10.0 203.0 303.0 300
3.0
MT.1
10.0 228.0 353.0 350
3.0
MT.1
10.0 253.0 403.0 400
3.0
MT.1
10.5 153.2 253.2 250
3.2
MT.1
10.5 203.2 303.2 300
3.2
MT.1
10.5 228.2 353.2 350
3.2
MT.1
10.5 253.2 403.2 400
3.2
MT.1
11.0 153.3 253.3 250
3.3
MT.1
11.0 203.3 303.3 300
3.3
MT.1
11.0 228.3 353.3 350
3.3
MT.1
11.0 253.3 403.3 400
3.3
MT.1
11.5 153.5 253.5 250

11.5 203.5 303.5 300
3.5
3.5
MT.1
MT.1
Order Number
LTDD1150A350M1
LTDD1150A400M1
LTDD1200A250M1
LTDD1200A300M1
LTDD1200A350M1
LTDD1200A400M1
LTDD1250A250M1
LTDD1250A300M1
LTDD1250A350M1
LTDD1250A400M1
LTDD1300A250M1
LTDD1300A300M1
LTDD1300A350M1
LTDD1300A400M1
LTDD1350A300M1
LTDD1350A350M1
LTDD1350A400M1
LTDD1350A450M1
LTDD1350A500M1
LTDD1350A600M1
LTDD1400A300M1
LTDD1400A350M1
LTDD1400A400M1
LTDD1400A450M1
LTDD1400A500M1
LTDD1400A600M1
LTDD1450A300M2
LTDD1450A350M2
LTDD1450A400M2
LTDD1450A450M2
LTDD1450A500M2
LTDD1450A600M2
LTDD1500A300M2
LTDD1500A350M2
LTDD1500A400M2
LTDD1500A450M2
LTDD1500A500M2
LTDD1500A600M2
LTDD1550A300M2
LTDD1550A350M2
DC
LCF OAL
Stock
Order Number
Stock
Unit : mm
LF
PL
CZC
11.5 228.5 353.5 350

11.5 253.5 403.5 400
3.5
3.5
MT.1
MT.1
12.0 153.6 253.6 250
3.6
MT.1
12.0 203.6 303.6 300
3.6
MT.1
12.0 228.6 353.6 350
3.6
MT.1
12.0 253.6 403.6 400
3.6
MT.1
12.5 153.8 253.8 250
3.8
MT.1
12.5 203.8 303.8 300
3.8
MT.1
12.5 228.8 353.8 350
3.8
MT.1
12.5 253.8 403.8 400
3.8
MT.1
13.0 153.9 253.9 250
3.9
MT.1
13.0 203.9 303.9 300
3.9
MT.1
13.0 228.9 353.9 350
3.9
MT.1
13.0 253.9 403.9 400
3.9
MT.1
13.5 204.1 304.1 300
4.1
MT.1
13.5 229.1 354.1 350
4.1
MT.1
13.5 254.1 404.1 400
4.1
MT.1
13.5 304.1 454.1 450
4.1
MT.1
13.5 354.1 504.1 500
4.1
MT.1
13.5 404.1 604.1 600
4.1
MT.1
14.0 204.2 304.2 300
4.2
MT.1
14.0 229.2 354.2 350
4.2
MT.1
14.0 254.2 404.2 400
4.2
MT.1
14.0 304.2 454.2 450
4.2
MT.1
14.0 354.2 504.2 500
4.2
MT.1
14.0 404.2 604.2 600
4.2
MT.1
14.5 179.4 304.4 300
4.4
MT.2
14.5 229.4 354.4 350
4.4
MT.2
14.5 254.4 404.4 400
4.4
MT.2
14.5 304.4 454.4 450
4.4
MT.2
14.5 354.4 504.4 500
4.4
MT.2
14.5 404.4 604.4 600
4.4
MT.2
15.0 179.5 304.5 300
4.5
MT.2
15.0 229.5 354.5 350
4.5
MT.2
15.0 254.5 404.5 400
4.5
MT.2
15.0 304.5 454.5 450
4.5
MT.2
15.0 354.5 504.5 500
4.5
MT.2
15.0 404.5 604.5 600
4.5
MT.2
15.5 179.7 304.7 300

15.5 229.7 354.7 350
4.7
4.7
MT.2
MT.2
HSS
LCF OAL
LF
PL
CZC
15.5 254.7 404.7 400

15.5 304.7 454.7 450
4.7
4.7
MT.2
MT.2
15.5 354.7 504.7 500
4.7
MT.2
15.5 404.7 604.7 600
4.7
MT.2
16.0 179.8 304.8 300
4.8
MT.2
16.0 229.8 354.8 350
4.8
MT.2
16.0 254.8 404.8 400
4.8
MT.2
16.0 304.8 454.8 450
4.8
MT.2
16.0 354.8 504.8 500
4.8
MT.2
16.0 404.8 604.8 600
4.8
MT.2
16.5 180.0 305.0 300
5.0
MT.2
16.5 230.0 355.0 350
5.0
MT.2
16.5 255.0 405.0 400
5.0
MT.2
16.5 305.0 455.0 450
5.0
MT.2
16.5 355.0 505.0 500
5.0
MT.2
16.5 405.0 605.0 600
5.0
MT.2
17.0 180.1 305.1 300
5.1
MT.2
17.0 230.1 355.1 350
5.1
MT.2
17.0 255.1 405.1 400
5.1
MT.2
17.0 305.1 455.1 450
5.1
MT.2
17.0 355.1 505.1 500
5.1
MT.2
17.0 405.1 605.1 600
5.1
MT.2
17.5 180.3 305.3 300
5.3
MT.2
17.5 230.3 355.3 350
5.3
MT.2
17.5 255.3 405.3 400
5.3
MT.2
17.5 305.3 455.3 450
5.3
MT.2
17.5 355.3 505.3 500
5.3
MT.2
17.5 405.3 605.3 600
5.3
MT.2
18.0 180.4 305.4 300
5.4
MT.2
18.0 230.4 355.4 350
5.4
MT.2
18.0 255.4 405.4 400
5.4
MT.2
18.0 305.4 455.4 450
5.4
MT.2
18.0 355.4 505.4 500
5.4
MT.2
18.0 405.4 605.4 600
5.4
MT.2
18.5 180.6 305.6 300
5.6
MT.2
18.5 230.6 355.6 350
5.6
MT.2
18.5 255.6 405.6 400
5.6
MT.2
18.5 305.6 455.6 450
5.6
MT.2
18.5 355.6 505.6 500
5.6
MT.2
18.5 405.6 605.6 600
5.6
MT.2
19.0 180.7 305.7 300
5.7
MT.2
19.0 230.7 355.7 350
5.7
MT.2
19.0 255.7 405.7 400
5.7
MT.2
19.0 305.7 455.7 450
5.7
MT.2
19.0 355.7 505.7 500
5.7
MT.2
19.0 405.7 605.7 600
5.7
MT.2
19.5 180.9 305.9 300
5.9
MT.2
19.5 230.9 355.9 350
5.9
MT.2
19.5 255.9 405.9 400

19.5 305.9 455.9 450
5.9
5.9
MT.2
MT.2
Order Number
LTDD1950A500M2
LTDD1950A600M2
LTDD2000A300M2
LTDD2000A350M2
LTDD2000A400M2
LTDD2000A450M2
LTDD2000A500M2
LTDD2000A600M2
LTDD2050A350M2
LTDD2050A400M2
LTDD2050A450M2
LTDD2050A500M2
LTDD2050A600M2
LTDD2100A350M2
LTDD2100A400M2
LTDD2100A450M2
LTDD2100A500M2
LTDD2100A600M2
LTDD2150A350M2
LTDD2150A400M2
LTDD2150A450M2
LTDD2150A500M2
LTDD2150A600M2
LTDD2200A350M2
LTDD2200A400M2
LTDD2200A450M2
LTDD2200A500M2
LTDD2200A600M2
LTDD2250A350M2
LTDD2250A400M2
LTDD2250A450M2
LTDD2250A500M2
LTDD2250A600M2
LTDD2300A350M2
LTDD2300A400M2
LTDD2300A450M2
LTDD2300A500M2
LTDD2300A600M2
LTDD2350A350M3
LTDD2350A400M3
LTDD2350A450M3
LTDD2350A500M3
LTDD2350A600M3
LTDD2400A350M3
LTDD2400A400M3
LTDD2400A450M3
LTDD2400A500M3
LTDD2400A600M3
LTDD2450A350M3
LTDD2450A400M3
DC
LCF OAL
LF
PL
CZC
19.5 355.9 505.9 500

19.5 405.9 605.9 600
5.9
5.9
MT.2
MT.2
20.0 181.0 306.0 300
6.0
MT.2
20.0 231.0 356.0 350
6.0
MT.2
20.0 256.0 406.0 400
6.0
MT.2
20.0 306.0 456.0 450
6.0
MT.2
20.0 356.0 506.0 500
6.0
MT.2
20.0 406.0 606.0 600
6.0
MT.2
20.5 231.2 356.2 350
6.2
MT.2
20.5 256.2 406.2 400
6.2
MT.2
20.5 306.2 456.2 450
6.2
MT.2
20.5 356.2 506.2 500
6.2
MT.2
20.5 406.2 606.2 600
6.2
MT.2
21.0 231.3 356.3 350
6.3
MT.2
21.0 256.3 406.3 400
6.3
MT.2
21.0 306.3 456.3 450
6.3
MT.2
21.0 356.3 506.3 500
6.3
MT.2
21.0 406.3 606.3 600
6.3
MT.2
21.5 231.5 356.5 350
6.5
MT.2
21.5 256.5 406.5 400
6.5
MT.2
21.5 306.5 456.5 450
6.5
MT.2
21.5 356.5 506.5 500
6.5
MT.2
21.5 406.5 606.5 600
6.5
MT.2
22.0 231.6 356.6 350
6.6
MT.2
22.0 256.6 406.6 400
6.6
MT.2
22.0 306.6 456.6 450
6.6
MT.2
22.0 356.6 506.6 500
6.6
MT.2
22.0 406.6 606.6 600
6.6
MT.2
22.5 231.8 356.8 350
6.8
MT.2
22.5 256.8 406.8 400
6.8
MT.2
22.5 306.8 456.8 450
6.8
MT.2
22.5 356.8 506.8 500
6.8
MT.2
22.5 406.8 606.8 600
6.8
MT.2
23.0 231.9 356.9 350
6.9
MT.2
23.0 256.9 406.9 400
6.9
MT.2
23.0 306.9 456.9 450
6.9
MT.2
23.0 356.9 506.9 500
6.9
MT.2
23.0 406.9 606.9 600
6.9
MT.2
23.5 207.1 357.1 350
7.1
MT.3
23.5 257.1 407.1 400
7.1
MT.3
23.5 307.1 457.1 450
7.1
MT.3
23.5 357.1 507.1 500
7.1
MT.3
23.5 407.1 607.1 600
7.1
MT.3
24.0 207.2 357.2 350
7.2
MT.3
24.0 257.2 407.2 400
7.2
MT.3
24.0 307.2 457.2 450
7.2
MT.3
24.0 357.2 507.2 500
7.2
MT.3
24.0 407.2 607.2 600
7.2
MT.3
24.5 207.4 357.4 350

24.5 257.4 407.4 400
7.4
7.4
MT.3
MT.3
DRILLING
LTDD1550A400M2
LTDD1550A450M2
LTDD1550A500M2
LTDD1550A600M2
LTDD1600A300M2
LTDD1600A350M2
LTDD1600A400M2
LTDD1600A450M2
LTDD1600A500M2
LTDD1600A600M2
LTDD1650A300M2
LTDD1650A350M2
LTDD1650A400M2
LTDD1650A450M2
LTDD1650A500M2
LTDD1650A600M2
LTDD1700A300M2
LTDD1700A350M2
LTDD1700A400M2
LTDD1700A450M2
LTDD1700A500M2
LTDD1700A600M2
LTDD1750A300M2
LTDD1750A350M2
LTDD1750A400M2
LTDD1750A450M2
LTDD1750A500M2
LTDD1750A600M2
LTDD1800A300M2
LTDD1800A350M2
LTDD1800A400M2
LTDD1800A450M2
LTDD1800A500M2
LTDD1800A600M2
LTDD1850A300M2
LTDD1850A350M2
LTDD1850A400M2
LTDD1850A450M2
LTDD1850A500M2
LTDD1850A600M2
LTDD1900A300M2
LTDD1900A350M2
LTDD1900A400M2
LTDD1900A450M2
LTDD1900A500M2
LTDD1900A600M2
LTDD1950A300M2
LTDD1950A350M2
LTDD1950A400M2
LTDD1950A450M2
DC
Stock
Order Number
Stock
Unit : mm
N193
TAPER SHANK DRILLS

HSS
LTD
Extra long
DRILLING
LTDD2450A450M3
LTDD2450A500M3
LTDD2450A600M3
LTDD2500A350M3
LTDD2500A400M3
LTDD2500A450M3
LTDD2500A500M3
LTDD2500A600M3
LTDD2550A400M3
LTDD2550A450M3
LTDD2550A500M3
LTDD2550A600M3
LTDD2600A400M3
LTDD2600A450M3
LTDD2600A500M3
LTDD2600A600M3
LTDD2650A400M3
LTDD2650A450M3
LTDD2650A500M3
LTDD2650A600M3
LTDD2700A400M3
LTDD2700A450M3
LTDD2700A500M3
LTDD2700A600M3
LTDD2750A400M3
LTDD2750A450M3
LTDD2750A500M3
LTDD2750A600M3
LTDD2800A400M3
LTDD2800A450M3
LTDD2800A500M3
LTDD2800A600M3
LTDD2850A400M3
LTDD2850A450M3
LTDD2850A500M3
LTDD2850A600M3
LTDD2900A400M3
LTDD2900A450M3
LTDD2900A500M3
LTDD2900A600M3
LTDD2950A400M3
LTDD2950A450M3
LTDD2950A500M3
LTDD2950A600M3
LTDD3000A400M3
LTDD3000A450M3
LTDD3000A500M3
LTDD3000A600M3
LTDD3050A450M3
LTDD3050A500M3
N194
DC
LCF OAL
LF
PL
CZC
24.5 307.4 457.4 450

24.5 357.4 507.4 500
7.4
7.4
MT.3
MT.3
24.5 407.4 607.4 600
7.4
MT.3
25.0 207.5 357.5 350
7.5
MT.3
25.0 257.5 407.5 400
7.5
MT.3
25.0 307.5 457.5 450
7.5
MT.3
25.0 357.5 507.5 500
7.5
MT.3
25.0 407.5 607.5 600
7.5
MT.3
25.5 257.7 407.7 400
7.7
MT.3
25.5 307.7 457.7 450
7.7
MT.3
25.5 357.7 507.7 500
7.7
MT.3
25.5 407.7 607.7 600
7.7
MT.3
26.0 257.8 407.8 400
7.8
MT.3
26.0 307.8 457.8 450
7.8
MT.3
26.0 357.8 507.8 500
7.8
MT.3
26.0 407.8 607.8 600
7.8
MT.3
26.5 258.0 408.0 400
8.0
MT.3
26.5 308.0 458.0 450
8.0
MT.3
26.5 358.0 508.0 500
8.0
MT.3
26.5 408.0 608.0 600
8.0
MT.3
27.0 258.1 408.1 400
8.1
MT.3
27.0 308.1 458.1 450
8.1
MT.3
27.0 358.1 508.1 500
8.1
MT.3
27.0 408.1 608.1 600
8.1
MT.3
27.5 258.3 408.3 400
8.3
MT.3
27.5 308.3 458.3 450
8.3
MT.3
27.5 358.3 508.3 500
8.3
MT.3
27.5 408.3 608.3 600
8.3
MT.3
28.0 258.4 408.4 400
8.4
MT.3
28.0 308.4 458.4 450
8.4
MT.3
28.0 358.4 508.4 500
8.4
MT.3
28.0 408.4 608.4 600
8.4
MT.3
28.5 258.6 408.6 400
8.6
MT.3
28.5 308.6 458.6 450
8.6
MT.3
28.5 358.6 508.6 500
8.6
MT.3
28.5 408.6 608.6 600
8.6
MT.3
29.0 258.7 408.7 400
8.7
MT.3
29.0 308.7 458.7 450
8.7
MT.3
29.0 358.7 508.7 500
8.7
MT.3
29.0 408.7 608.7 600
8.7
MT.3
29.5 258.9 408.9 400
8.9
MT.3
29.5 308.9 458.9 450
8.9
MT.3
29.5 358.9 508.9 500
8.9
MT.3
29.5 408.9 608.9 600
8.9
MT.3
30.0 259.0 409.0 400
9.0
MT.3
30.0 309.0 459.0 450
9.0
MT.3
30.0 359.0 509.0 500
9.0
MT.3
30.0 409.0 609.0 600
9.0
MT.3
30.5 309.2 459.2 450

30.5 359.2 509.2 500
9.2
9.2
MT.3
MT.3
Order Number
LTDD3050A600M3
LTDD3100A450M3
LTDD3100A500M3
LTDD3100A600M3
LTDD3150A450M3
LTDD3150A500M3
LTDD3150A600M3
LTDD3200A450M3
LTDD3200A500M3
LTDD3200A600M3
LTDD3300A500M4
LTDD3300A600M4
LTDD3400A500M4
LTDD3400A600M4
LTDD3500A500M4
LTDD3500A600M4
LTDD3600A500M4
LTDD3600A600M4
LTDD3700A500M4
LTDD3700A600M4
LTDD3800A500M4
LTDD3800A600M4
LTDD3900A500M4
LTDD3900A600M4
LTDD4000A500M4
LTDD4000A600M4
DC
LCF OAL
Stock
Order Number
Stock
Unit : mm
LF
PL
CZC
30.5 409.2 609.2 600

31.0 309.3 459.3 450
9.2
9.3
MT.3
MT.3
31.0 359.3 509.3 500
9.3
MT.3
31.0 409.3 609.3 600
9.3
MT.3
31.5 309.5 459.5 450
9.5
MT.3
31.5 359.5 509.5 500
9.5
MT.3
31.5 409.5 609.5 600
9.5
MT.3
32.0 309.6 459.6 450
9.6
MT.3
32.0 359.6 509.6 500
9.6
MT.3
32.0 409.6 609.6 600
9.6
MT.3
33.0 359.9 509.9 500
9.9
MT.4
33.0 409.9 609.9 600
9.9
MT.4
34.0 360.2 510.2 500
10.2
MT.4
34.0 410.2 610.2 600
10.2
MT.4
35.0 360.5 510.5 500
10.5
MT.4
35.0 410.5 610.5 600
10.5
MT.4
36.0 360.8 510.8 500
10.8
MT.4
36.0 410.8 610.8 600
10.8
MT.4
37.0 361.1 511.1
11.1
MT.4
500
37.0 411.1 611.1
600
11.1
MT.4
38.0 361.4 511.4
500
11.4
MT.4
38.0 411.4 611.4
600
11.4
MT.4
39.0 361.7 511.7
500
11.7
MT.4
39.0 411.7 611.7
600
11.7
MT.4
40.0 362.0 512.0 500

40.0 412.0 612.0 600
12.0
12.0
MT.4
MT.4
a
a
GTTD
TiN, For steel frame
P
HSS
160
Thinning
100
HSS
17 < DC < 18 18<DC < 30 30<DC < 32
0
0.027
Steel
PL
0
0.033
0
0.039
DC
LF
LCF
CZC
a Special point geometry for minimal through hole burrs.
Stock
Unit : mm
Order Number
DC
LCF
LF
PL
CZC
GTTDD1700M3
GTTDD1750M3
GTTDD1800M3
GTTDD1900M3
GTTDD2000M3
GTTDD2150M3
GTTDD2200M3
GTTDD2250M3
GTTDD2300M3
GTTDD2350M3
GTTDD2400M3
GTTDD2450M3
GTTDD2500M3
GTTDD2600M3
GTTDD2650M3
GTTDD2800M4
GTTDD3200M4
17.0
17.5
135
140
255
260
2.9
3.0
MT.3
MT.3
18.0
140
260
3.0
MT.3
19.0
145
265
3.2
MT.3
20.0
150
270
3.3
MT.3
21.5
160
280
3.6
MT.3
22.0
160
280
3.7
MT.3
22.5
165
285
3.8
MT.3
23.0
165
285
3.8
MT.3
23.5
165
285
4.0
MT.3
24.0
165
285
4.0
MT.3
24.5
165
285
4.1
MT.3
25.0
165
285
4.1
MT.3
26.0
165
285
4.3
MT.3
26.5
170
290
4.4
MT.3
28.0
32.0
175
195
320
340
4.5
5.0
MT.4
MT.4
DRILLING
CUTTING CONDITIONS
N198
N195
TAPER SHANK DRILLS

HSS
TTD
For steel frame
P
HSS
160
Thinning
100
17 < DC < 1818<DC < 3030<DC < 32
0
0.027
Steel
PL
0
0.033
0
0.039
DC
LF
LCF
CZC
a Special point geometry for minimal through hole burrs.
Stock
Unit : mm
Order Number
DC
LCF
LF
PL
CZC
TTDD1700M3
TTDD1750M3
TTDD1800M3
TTDD1900M3
TTDD2000M3
TTDD2150M3
TTDD2200M3
TTDD2250M3
TTDD2300M3
TTDD2350M3
TTDD2400M3
TTDD2450M3
TTDD2500M3
TTDD2600M3
TTDD2650M3
TTDD2800M4
TTDD3200M4
17.0
17.5
135
140
255
260
2.9
3.0
MT.3
MT.3
18.0
140
260
3.0
MT.3
19.0
145
265
3.2
MT.3
20.0
150
270
3.3
MT.3
21.5
160
280
3.6
MT.3
22.0
160
280
3.7
MT.3
22.5
165
285
3.8
MT.3
23.0
165
285
3.8
MT.3
23.5
165
285
4.0
MT.3
24.0
165
285
4.0
MT.3
24.5
165
285
4.1
MT.3
25.0
165
285
4.1
MT.3
26.0
165
285
4.3
MT.3
26.5
170
290
4.4
MT.3
28.0
32.0
175
195
320
340
4.5
5.0
MT.4
MT.4
DRILLING
N196

CUTTING CONDITIONS
N199
TRIANGULAR SHANK DRILLS
3KD
Triangular shank (Type 6.5)(Type 10)(Type 13)
P
Steel
118
HSS
HSS
7 < DC < 10 10<DC < 18 18<DC < 26
0
0.022

PL
0
0.027
0
0.033
DC
DCON
LF
LCF
OAL
a 3 shank types for portable power tools.
OAL
LF
PL
DCON
7.0
7.5
37.1
37.3
77.1
77.3
75
75
2.1
2.3
6.5
6.5
8.0
37.4
77.4
75
2.4
6.5
8.5
37.6
77.6
75
2.6
6.5
9.0
37.7
77.7
75
2.7
6.5
9.5
37.9
77.9
75
2.9
6.5
10.0
53.0
93.0
90
3.0
6.5
10.5
53.2
93.2
90
3.2
6.5
11.0
53.3
93.3
90
3.3
6.5
3KD10D1000
3KD10D1050
3KD10D1100
3KD10D1150
3KD10D1200
3KD10D1250
3KD10D1300
3KD10D1350
3KD10D1400
3KD10D1450
3KD10D1500
3KD10D1550
3KD10D1600
11.5
53.5
93.5
90
3.5
6.5
12.0
53.6
93.6
90
3.6
6.5
12.5
13.0
53.8
53.9
93.8
93.9
90
90
3.8
3.9
6.5
6.5
Type 10
Order Number
Stock
LCF
Unit : mm
DC
LCF
OAL
LF
PL
DCON
10.0
10.5
53.0
53.2
93.0
93.2
90
90
3.0
3.2
10
10
11.0
53.3
93.3
90
3.3
10
11.5
53.5
93.5
90
3.5
10
12.0
53.6
93.6
90
3.6
10
12.5
53.8
93.8
90
3.8
10
13.0
53.9
93.9
90
3.9
10
13.5
89.1 144.1 140
4.1
10
14.0
89.2 144.2 140
4.2
10
14.5
89.4 144.4 140
4.4
10
15.0
89.5 144.5 140
4.5
10
15.5
16.0
89.7 144.7 140

89.8 144.8 140
4.7
4.8
10
10
Type 13
Unit : mm
Order Number
DC
3KD13D1350
3KD13D1400
3KD13D1450
3KD13D1500
3KD13D1550
3KD13D1600
3KD13D1650
3KD13D1700
3KD13D1750
3KD13D1800
3KD13D1850
3KD13D1900
3KD13D1950
3KD13D2000
3KD13D2050
3KD13D2100
3KD13D2150
3KD13D2200
3KD13D2250
3KD13D2300
3KD13D2350
3KD13D2400
3KD13D2450
3KD13D2500
3KD13D2550
3KD13D2600
13.5
14.0
LCF
OAL
LF
PL
DCON
89.1 144.1
89.2 144.2
140
140
4.1
4.2
13
13
14.5
89.4 144.4
140
4.4
13
15.0
89.5 144.5
140
4.5
13
15.5
89.7 144.7
140
4.7
13
16.0
89.8 144.8
140
4.8
13
16.5
90.0 145.0
140
5.0
13
17.0
90.1 145.1
140
5.1
13
17.5
90.3 145.3
140
5.3
13
18.0
90.4 145.4
140
5.4
13
18.5
90.6 145.6
140
5.6
13
19.0
90.7 145.7
140
5.7
13
19.5
90.9 145.9
140
5.9
13
20.0
91.0 146.0
140
6.0
13
20.5
91.2 146.2
140
6.2
13
21.0
91.3 146.3
140
6.3
13
21.5
91.5 146.5
140
6.5
13
22.0
91.6 146.6
140
6.6
13
22.5
91.8 146.8
140
6.8
13
23.0
91.9 146.9
140
6.9
13
23.5
92.1 147.1
140
7.1
13
24.0
92.2 147.2
140
7.2
13
24.5
92.4 147.4
140
7.4
13
25.0
92.5 147.5
140
7.5
13
25.5
26.0
92.7 147.7
92.8 147.8
140
140
7.7
7.8
13
13
DRILLING
3KD6D0700
3KD6D0750
3KD6D0800
3KD6D0850
3KD6D0900
3KD6D0950
3KD6D1000
3KD6D1050
3KD6D1100
3KD6D1150
3KD6D1200
3KD6D1250
3KD6D1300
DC
Stock
Order Number
Unit : mm
Stock
Type 6.5
N197
STRAIGHT SHANK DRILLS/TAPER SHANK DRILLS

HSS
GSD GWSS GWSL GTD GWTS GTTD

TiN coated drills

Work
material
Structural steel SS
Carbon steel S-C
( 25HRC)
Alloy steel SCM

Tool steel SK
( 35HRC)
Cast iron FC
Alloy steel SCM

Die steel SKD
( 40HRC)
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
0.5
1.0
2.0
3.0
6.0
8.0
10.0
8000
6000
4700
3200
1600
1200
960
0.01
0.02
0.05
0.10
0.18
0.20
0.22
7000
5500
3600
2400
1200
900
720
0.008
0.01
0.03
0.08
0.15
0.18
0.20
6000
4500
2400
1800
900
680
550
0.005
0.008
0.02
0.05
0.13
0.15
0.18
8000
6000
4700
3500
1750
1300
1100
0.01
0.02
0.05
0.10
0.18
0.20
0.22
12.0
800
0.24
600
0.22
450
0.20
880
0.24
15.0
630
0.28
480
0.24
350
0.22
700
0.28
20.0
470
0.33
360
0.26
260
0.24
530
0.33
25.0
30.0
380
310
0.36
0.40
290
240
0.28
0.30
210
180
0.26
0.28
420
330
0.36
0.40
Stainless steel
Work
material
DRILLING
Dia.
DC (mm)
Martensitic
Ferritic AISI 430
Austenitic AISI 304

ASTM 630
Copper alloy, Brass
Aluminium alloy
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
0.5
1.0
2.0
3.0
6.0
8000
5000
2500
1900
950
0.01
0.02
0.05
0.10
0.18
6000
4000
2300
1500
750
0.01
0.02
0.04
0.07
0.10
8000
6000
4700
3200
1600
0.01
0.02
0.05
0.10
0.18
10000
7000
6000
5500
3100
0.02
0.04
0.08
0.13
0.23
8.0
700
0.20
530
0.13
1200
0.20
2300
0.28
10.0
560
0.22
420
0.15
960
0.22
1900
0.33
12.0
460
0.24
340
0.17
800
0.24
1600
0.38
15.0
360
0.26
270
0.20
630
0.26
1300
0.42
20.0
25.0
30.0
270
210
180
0.28
0.32
0.35
200
160
135
0.23
0.24
0.25
470
380
310
0.28
0.32
0.35
950
750
630
0.45
0.48
0.50
1) Please reduce the cutting conditions when drilling a deep hole.

2) This table only shows standard cutting conditions with water-soluble cutting fluids. Please make corrections or adjustments depending on
the application.
y Reduction rate of cutting conditions for hole drilling

Drilling
depth
Reduction rate of
cutting speed
Reduction rate of feed
Drilling
depth
Reduction rate of
cutting speed
4D
5D
10%
10%
10%
15%
8D
10D
30%
30%
20%
25%
6D
7D
20%
20%
20%
20%
15D
20D
40%
40%
30%
45%
D : Drill dia.
N198
SD
KSD
LSD
TD
KTD
TTD
HSS
Standard drills

Work
material
Dia.
DC (mm)
Structural steel SS
Carbon steel S-C
( 25HRC)
Alloy steel SCM

Tool steel SK
( 35HRC)
Cast iron FC
Alloy steel SCM

Die steel SKD
( 40HRC)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
0.5
1.0
6000
5000
0.01
0.02
5000
4000
0.008
0.01
4000
2800
0.005
0.008
6000
5000
0.01
0.02
2.0
3.0
6.0
8.0
10.0
12.0
3000
2100
1100
800
650
520
0.05
0.10
0.18
0.20
0.22
0.24
2500
1800
900
670
540
450
0.03
0.08
0.15
0.18
0.20
0.22
1800
1200
600
450
350
300
0.02
0.05
0.13
0.15
0.18
0.20
3000
2300
1100
900
700
600
0.05
0.10
0.18
0.20
0.22
0.24
15.0
420
0.28
360
0.24
240
0.22
470
0.28
20.0
320
0.33
270
0.26
180
0.24
350
0.33
25.0
250
0.36
210
0.28
145
0.26
280
0.36
30.0
40.0
210
160
0.40
0.42
180
130
0.30
0.32
120
90
0.28
0.30
230
180
0.40
0.42
Stainless steel
Dia.
DC (mm)
Martensitic
Ferritic AISI 430
Austenitic AISI 304

ASTM 630
Copper alloy, Brass
Aluminium alloy
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
0.5
1.0
2.0
3.0
6.0
5000
4000
2200
1600
800
0.01
0.02
0.05
0.10
0.18
4000
3000
1500
1000
530
0.01
0.02
0.04
0.07
0.10
6000
5000
3000
2100
1100
0.01
0.02
0.05
0.10
0.18
10000
7000
5000
4200
2100
0.02
0.04
0.08
0.13
0.23
8.0
600
0.20
400
0.13
800
0.20
1600
0.28
10.0
480
0.22
310
0.15
650
0.22
1200
0.33
12.0
400
0.24
250
0.17
520
0.24
1000
0.38
15.0
320
0.26
170
0.20
420
0.26
850
0.42
20.0
25.0
30.0
40.0
240
190
160
120
0.28
0.32
0.35
0.38
130
100
85
65
0.23
0.24
0.25
0.28
320
250
210
160
0.28
0.32
0.35
0.38
630
500
400
300
0.45
0.48
0.50
0.52
1) Please reduce the cutting conditions when drilling a deep hole.

2) This table only shows standard cutting conditions with water-soluble cutting fluids. Please make corrections or adjustments depending on
the application.
DRILLING
Work
material
y Reduction rate of cutting conditions for hole drilling

Drilling
depth
Reduction rate of
cutting speed
Drilling
depth
Reduction rate of
cutting speed
4D
5D
10%
10%
10%
15%
8D
10D
30%
30%
20%
25%
6D
7D
20%
20%
20%
20%
15D
20D
40%
40%
30%
45%
D : Drill dia.
N199
DRILLING(BRAZED TYPE)
CARBIDE
BRS
P
Steel
aExcellent cutting sharpness and chip discharge due to high rake type insert.
aHigh efficiency, high accuracy machining.
14 < DC < 18 18<DC < 30
0
0.018
0
0.021
(I/d=3)
DCON
LF
150
DC(h7)
PL
LU
LH
OAL
Standard Diameter
Dimensions (mm)
(mm)
Order Number
14.0
14.5
15.0
15.5
16.0
16.5
17.0
17.5
18.0
18.5
19.0
19.5
20.0
20.5
21.0
21.5
22.0
22.5
23.0
23.5
24.0
24.5
25.0
25.5
26.0
26.5
27.0
27.5
28.0
28.5
29.0
29.5
30.0
BRS1400S16
BRS1450S16
BRS1500S20
BRS1550S20
BRS1600S20
BRS1650S20
BRS1700S20
BRS1750S20
BRS1800S20
BRS1850S20
BRS1900S25
BRS1950S25
BRS2000S25
BRS2050S25
BRS2100S25
BRS2150S25
BRS2200S25
BRS2250S25
BRS2300S25
BRS2350S25
BRS2400S32
BRS2450S32
BRS2500S32
BRS2550S32
BRS2600S32
BRS2650S32
BRS2700S32
BRS2750S32
BRS2800S32
BRS2850S32
BRS2900S32
BRS2950S32
BRS3000S32
UP20M
Stock
DC
DRILLING
Intermediate Diameters
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Range of Drill Diameters (DC)
Order Number
14.0<DC < 14.5
BRSrrrrS16
LU
LH OAL LF
53.9 67.9 115.9 114

53.9 67.9 115.9 114
1.9
1.9
16
16
63.0 78.0 128.0 126

63.1 78.1 128.1 126
2.0
2.1
20
20
67.1 83.1 133.1 131
2.1
20
67.2 83.2 133.2 131
2.2
20
71.3 88.3 138.3 136
2.3
20
71.3 88.3 138.3 136
2.3
20
17.5<DC < 18.5
75.4 93.4 143.4 141

75.5 93.5 143.5 141
2.4
2.5
20
20
18.5<DC < 19.5
79.5 103.5 159.5 157

79.6 103.6 159.6 157
2.5
2.6
25
25
83.7 103.7 159.7 157
2.7
25
83.7 103.7 159.7 157
2.7
25
82.8 103.8 159.8 157
2.8
25
82.9 103.9 159.9 157
2.9
25
86.9 108.9 164.9 162
2.9
25
87.0 109.0 165.0 162
3.0
25
22.5<DC < 23.5
86.1 109.1 165.1 162

86.1 109.1 165.1 162
3.1
3.1
25
25
23.5<DC < 24.5
90.2 114.2 174.2 171

90.3 114.3 174.3 171
3.2
3.3
32
32
89.3 114.3 174.3 171
3.3
32
89.4 114.4 174.4 171
3.4
32
93.5 119.5 179.5 176
3.5
32
93.6 119.6 179.6 176
3.6
32
92.6 119.6 179.6 176
3.6
32
92.7 119.7 179.7 176
3.7
32
96.8 124.8 184.8 181
3.8
32
96.8 124.8 184.8 181
3.8
32
100.9 129.9 189.9 186
3.9
32
101.0 130.0 190.0 186

100.0 130.0 190.0 186
4.0
4.0
32
32
14.5<DC < 15.5

15.5<DC < 16.5
BRSrrrrS20
16.5<DC < 17.5
19.5<DC < 20.5

20.5<DC < 21.5
BRSrrrrS25
21.5<DC < 22.5
24.5<DC < 25.5

25.5<DC < 26.5
26.5<DC < 27.5
27.5<DC < 28.5
28.5<DC < 29.5
29.5<DC < 30.5
BRSrrrrS32
For ordering an intermediate diameter, please enter the diameter (DC) into the 4-digit spacerrrrin the nominal designation.
(Ex. UP20M BRSr
2r
5r
3r
0 S32 for a diameter of & 25.30mm)
a
N200
PL DCON
CARBIDE

Work Material
Hardness
Drill Dia. & 20.0 & 30.0

Cutting Speed
Feed
(m/min)
(mm/rev)
< 180HB
65 (50 75)
0.3 (0.20 0.40)
70 (55 85)
0.35 (0.20 0.45)
SS400 (JIS)
80 (70 90)
0.30 (0.25 0.35)
80 (70 90)
0.35 (0.30 0.45)
SM490 (JIS)
70 (60 80)
0.25 (0.20 0.30)
70 (60 80)
0.30 (0.20 0.40)
SM570 (JIS)
60 (50 70)
0.25 (0.20 0.30)
60 (50 70)
0.30 (0.20 0.35)
180 280HB
60 (45 70)
0.25 (0.1 0.35)
65 (45 80)
0.30 (0.15 0.35)
280 350HB
55 (40 65)
0.20 (0.15 0.35)
60 (45 70)
0.25 (0.15 0.35)
70 (50 90)
0.30 (0.20 0.40)
80 (60 100)
0.3 (0.20 0.40)
Mild Steel
Structural Steel
Drill Dia. & 14.0 & 20.0

Cutting Speed
Feed
(m/min)
(mm/rev)
Carbon Steel
Alloy Steel
Stainless Steel (Austenitic)
< 200HB
Gray Cast Iron
75 (60 110)
0.30 (0.20 0.40)
80 (60 100)
0.35 (0.25 0.50)
75 (60 100)
0.30 (0.20 0.40)
80 (60 100)
0.35 (0.20 0.45)
70 (55 90)
0.25 (0.15 0.35)
75 (55 90)
0.30 (0.15 0.40)
Ductile Cast Iron
(Note) The above conditions are for general cutting. The cutting conditions need to be modified depending on power, rigidity of the machine
and workpiece shape.
Workpiece : JIS SUS304 Drilled Depth : l/d=3(Through Hole) Cutting Speed : 70m/min WSO (10%)
Thrust
v
m/re
f=0.30mm/rev
f=0.
25m
f=0.
f=0.1
4
f=0.20mm/rev
2
f=0.30mm/rev
8000
/re
5mm
20
25
Drill Diameter (mm)
30
f=0.3
/rev
5mm
f=0.2
6000
mm/re
f=0.15
4000
f=0.20mm/rev
2000
15
/rev
5mm
10000
v
m/re
15
20
25
Drill Diameter (mm)
30
DRILLING
35m
Thrust (N)
Power Consumption
TECHNICAL DATA
Q001
N201
CARBIDE
BRM
P
Steel
aExcellent cutting sharpness and chip discharge due to high rake type insert.
aHigh efficiency, high accuracy machining.
14 < DC < 18 18<DC < 30
0
0.027
0
0.033
(I/d=5)
DCON
LF
150
DC(h8)
PL
LU
LH
OAL
Standard Diameter
Dimensions (mm)
(mm)
Order Number
14.0
14.5
15.0
15.5
16.0
16.5
17.0
17.5
18.0
18.5
19.0
19.5
20.0
20.5
21.0
21.5
22.0
22.5
23.0
23.5
24.0
24.5
25.0
25.5
26.0
26.5
27.0
27.5
28.0
28.5
29.0
29.5
30.0
BRM1400S16
BRM1450S16
BRM1500S20
BRM1550S20
BRM1600S20
BRM1650S20
BRM1700S20
BRM1750S20
BRM1800S20
BRM1850S20
BRM1900S25
BRM1950S25
BRM2000S25
BRM2050S25
BRM2100S25
BRM2150S25
BRM2200S25
BRM2250S25
BRM2300S25
BRM2350S25
BRM2400S32
BRM2450S32
BRM2500S32
BRM2550S32
BRM2600S32
BRM2650S32
BRM2700S32
BRM2750S32
BRM2800S32
BRM2850S32
BRM2900S32
BRM2950S32
BRM3000S32
UP20M
Stock
DC
DRILLING
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Order Number
14.0<DC < 14.5
BRMrrrrS16
LU
LH OAL LF
79.9 93.9 141.9 140

79.9 93.9 141.9 140
1.9
1.9
16
16
87.0 102.0 152.0 150

87.1 102.1 152.1 150
2.0
2.1
20
20
91.1 107.1 157.1 155
2.1
20
91.2 107.2 157.2 155
2.2
20
100.3 117.3 167.3 165
2.3
20
100.3 117.3 167.3 165
2.3
20
17.5<DC < 18.5
104.4 122.4 172.4 170

104.5 122.5 172.5 170
2.4
2.5
20
20
18.5<DC < 19.5
107.5 126.5 182.5 180

107.6 126.6 182.6 180
2.5
2.6
25
25
116.7 136.7 192.7 190
2.7
25
116.7 136.7 192.7 190
2.7
25
120.8 141.8 197.8 195
2.8
25
120.9 141.9 197.9 195
2.9
25
124.9 146.9 202.9 200
2.9
25
125.0 147.0 203.0 200
3.0
25
22.5<DC < 23.5
129.1 152.1 208.1 205

129.1 152.1 208.1 205
3.1
3.1
25
25
23.5<DC < 24.5
139.2 163.2 223.2 220

139.3 163.3 223.3 220
3.2
3.3
32
32
143.3 168.3 228.3 225
3.3
32
143.4 168.4 228.4 225
3.4
32
147.5 173.5 233.5 230
3.5
32
147.6 173.6 233.6 230
3.6
32
151.6 178.6 238.6 235
3.6
32
151.7 178.7 238.7 235
3.7
32
160.8 188.8 248.8 245
3.8
32
160.8 188.8 248.8 245
3.8
32
164.9 193.9 253.9 250
3.9
32
165.0 194.0 254.0 250

169.0 199.0 259.0 255
4.0
4.0
32
32
14.5<DC < 15.5

15.5<DC < 16.5
BRMrrrrS20
16.5<DC < 17.5
19.5<DC < 20.5

20.5<DC < 21.5
BRMrrrrS25
21.5<DC < 22.5
24.5<DC < 25.5

25.5<DC < 26.5
26.5<DC < 27.5
27.5<DC < 28.5
28.5<DC < 29.5
29.5<DC < 30.0
BRMrrrrS32
For ordering an intermediate diameter, please enter the diameter (DC) into the 4-digit spacerrrrin the nominal designation.
(Ex. UP20M BRMr
2r
5r
3r
a
N202
PL DCON
CARBIDE

Work Material
Hardness
Drill Dia. & 20.0 & 30.0

Cutting Speed
Feed
(m/min)
(mm/rev)
< 180HB
65 (50 75)
0.30 (0.20 0.40)
70 (55 85)
0.35 (0.20 0.45)
SS400 (JIS)
70 (60 80)
0.30 (0.25 0.35)
70 (60 80)
0.35 (0.30 0.45)
SM490 (JIS)
60 (50 70)
0.25 (0.20 0.30)
60 (50 70)
0.30 (0.20 0.40)
SM570 (JIS)
50 (40 60)
0.25 (0.20 0.30)
50 (40 60)
0.30 (0.20 0.35)
180 280HB
60 (45 70)
0.25 (0.15 0.35)
65 (45 80)
0.30 (0.15 0.40)
280 350HB
55 (40 65)
0.20 (0.15 0.35)
60 (45 70)
0.25 (0.15 0.35)
60 (50 80)
0.25 (0.15 0.35)
65 (50 80)
0.30 (0.20 0.40)
Mild Steel
Structural Steel
Drill Dia. & 14.0 & 20.0

Cutting Speed
Feed
(m/min)
(mm/rev)
Carbon Steel
Alloy Steel
Stainless Steel (Austenitic)
< 200HB
Gray Cast Iron
65 (50 100)
0.30 (0.20 0.40)
70 (50 100)
0.35 (0.25 0.50)
65 (50 90)
0.30 (0.2 0.40)
70 (50 90)
0.35 (0.20 0.45)
60 (45 80)
0.25 (0.15 0.35)
65 (45 80)
0.30 (0.15 0.40)
Ductile Cast Iron
Workpiece : JIS SUS304 Drilled Depth : l/d=5(Through Hole) Cutting Speed : 60m/min WSO (10%)
f=
m/rev
f=0.2m
f=0.1mm/rev
f=0.4
10000
f=0.
/rev
0.3mm
ev
mm/r
/re
4mm
m/rev
8000
f=0.3m
6000
f=0.2mm
4000
f=0.1mm/re
/rev
2000
15
20
25
Drill Diameter (mm)
30
15
20
25
Drill Diameter (mm)
30
DRILLING
Thrust
Thrust (N)
Power Consumption
TECHNICAL DATA
Q001
N203
CARBIDE
BRSB
Key point drill for bridge construction
P
aExcellent cutting sharpness and chip discharge
due to high rake type insert.

aUnique flute shape is used. (l/d=3)
18<DC < 30
0
0.021
Steel
a Key point drill for bridge construction
(I/d=3)
DCON
LF
150
DC(h7)
PL
LU
LH
OAL
Stock
Order Number
UP20M
DC
(mm)
24.5
24.6
24.7
26.5
26.7
BRSB2450S32
BRSB2460S32
BRSB2470S32
BRSB2650S32
BRSB2670S32
BRMB
Key point drill for bridge construction
P
Dimensions (mm)
LU
LH
OAL
LF
PL
DCON
90.3
89.3
114.3
114.3
174.3
174.3
171
171
3.3
3.3
32
32
89.3
114.3
174.3
171
3.3
32
93.6
92.6
119.6
119.6
179.6
179.6
176
176
3.6
3.6
32
32
aExcellent cutting sharpness and chip discharge
due to high rake type insert.

aUnique flute shape is used. (l/d=5)
18<DC < 30
0
0.021
Steel
a Key point drill for bridge construction
(I/d=5)
DCON
LF
150
DC(h7)
PL
LU
LH
OAL
DRILLING
Stock
N204
Order Number
UP20M
DC
(mm)
24.5
24.6
24.7
26.5
26.7
BRMB2450S32
BRMB2460S32
BRMB2470S32
BRMB2650S32
BRMB2670S32
Dimensions (mm)
LU
LH
OAL
LF
PL
DCON
139.3
143.3
163.3
168.3
223.3
228.3
220
225
3.3
3.3
32
32
143.3
168.3
228.3
225
3.3
32
147.6
151.6
173.6
178.6
233.6
238.6
230
235
3.6
3.6
32
32
BRB
New point drill for bridge construction parts
aLow thrust due to the absence of a chisel edge.

aEasy regrinding.
CARBIDE
18<DC < 30
0
0.021
Steel
a New point drill for bridge construction parts
(I/d=3)
DCON
LF
150
DC(h7)
PL
LU
LH
OAL
Stock
Order Number
UTi20T
DC
(mm)
24.5
24.6
24.7
26.5
26.7
BRB2450S32M
BRB2460S32M
BRB2470S32M
BRB2650S32M
BRB2670S32M
Dimensions (mm)
LU
LH
OAL
LF
PL
DCON
90.3
89.3
114.3
114.3
174.3
174.3
171
171
3.3
3.3
32
32
89.3
114.3
174.3
171
3.3
32
93.6
92.6
119.6
119.6
179.6
179.6
176
176
3.6
3.6
32
32

Work Material
BRB
BRSB
BRMB
Cutting Speed
(m/min)
Feed
(mm/rev)
Cutting Speed
(m/min)
Feed
(mm/rev)
Cutting Speed
(m/min)
Feed
(mm/rev)
SS400
(JIS)
Tensile Strength
400 500MPa
65 (60 75)
0.35 (0.3 0.4)
80 (70 90)
0.35 (0.3 0.45)
70 (60 80)
0.35 (0.3 0.45)
Structural SM490
(JIS)
Steel
Tensile Strength
490 610MPa
60 (50 70)
0.3 (0.2 0.4)
70 (60 80)
0.3 (0.2 0.4)
60 (50 70)
0.3 (0.2 0.4)
SM570
(JIS)
Tensile Strength
570 720MPa
55 (50 60)
0.3 (0.2 0.35)
60 (50 70)
0.3 (0.2 0.35)
50 (40 60)
0.3 (0.2 0.35)
< 180HB
40 (30 50)
70 (55 85)
0.35 (0.2 0.45)
70 (55 85)
0.35 (0.2 0.45)
Mild Steel
0.35 (0.25 0.4)
DRILLING
Hardness
TECHNICAL DATA
Q001
N205
CARBIDE
BRA
P
Steel

aEasy regrinding.
8 < D < 10
10<DC < 18
18<DC < 30
30<DC < 40
0
0.015
0
0.018
0
0.021
0
0.025
a General Use (Carbon Steel, Alloy Steel, Stainless Steel)
(I/d=3)
DCON
LF
150
DC(h7)
PL
LU
LH
OAL
Standard Diameter
DRILLING
N206
Dimensions (mm)
Order Number
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
12.5
13.0
13.5
14.0
14.5
15.0
15.5
16.0
16.5
17.0
17.5
18.0
18.5
19.0
19.5
20.0
20.5
21.0
21.5
22.0
22.5
23.0
23.5
BRA0800S16
BRA0850S16
BRA0900S16
BRA0950S16
BRA1000S16
BRA1050S16
BRA1100S16
BRA1150S16
BRA1200S16
BRA1250S16
BRA1300S16
BRA1350S16
BRA1400S16
BRA1450S16
BRA1500S20
BRA1550S20
BRA1600S20
BRA1650S20
BRA1700S20
BRA1750S20
BRA1800S20
BRA1850S20
BRA1900S25
BRA1950S25
BRA2000S25
BRA2050S25
BRA2100S25
BRA2150S25
BRA2200S25
BRA2250S25
BRA2300S25
BRA2350S25
UP20M
Stock
DC
(mm)
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
LU
LH OAL LF
PL DCON
24.1
24.1
36.1 84.1
36.1 84.1
83
83
1.1
1.1
16
16
29.2
41.2 89.2
88
1.2
16
29.3
41.3 89.3
88
1.3
16
36.3
46.3 94.3
93
1.3
16
36.4
46.4 94.4
93
1.4
16
41.5
52.5 100.5
99
1.5
16
41.5
52.5 100.5
99
1.5
16
45.6
57.6 105.6 104
1.6
16
45.7
57.7 105.7 104
1.7
16
49.7
62.7 110.7 109
1.7
16
49.8
62.8 110.8 109
1.8
16
13.5<DC<14.5
53.9
53.9
67.9 115.9 114

67.9 115.9 114
1.9
1.9
16
16
14.5<DC<15.5
63.0
63.1
78.0 128.0 126

78.1 128.1 126
2.0
2.1
20
20
67.1
83.1 133.1 131
2.1
20
67.2
83.2 133.2 131
2.2
20
71.3
88.3 138.3 136
2.3
20
71.3
88.3 138.3 136
2.3
20
17.5<DC<18.5
75.4
75.5
93.4 143.4 141

93.5 143.5 141
2.4
2.5
20
20
18.5<DC<19.5
79.5 103.5 159.5 157

79.6 103.6 159.6 157
2.5
2.6
25
25
83.7 103.7 159.7 157
2.7
25
83.7 103.7 159.7 157
2.7
25
82.8 103.8 159.8 157
2.8
25
82.9 103.9 159.9 157
2.9
25
86.9 108.9 164.9 162
2.9
25
87.0 109.0 165.0 162
3.0
25
86.1 109.1 165.1 162

86.1 109.1 165.1 162
3.1
3.1
25
25
Order Number
8.0<DC<8.5
8.5<DC<9.5
9.5<DC<10.5
10.5<DC<11.5
BRArrrrS16
11.5<DC<12.5
12.5<DC<13.5
15.5<DC<16.5
BRArrrrS20
16.5<DC<17.5
19.5<DC<20.5
20.5<DC<21.5
BRArrrrS25
21.5<DC<22.5
22.5<DC<23.5
CARBIDE
Standard Diameter
Dimensions (mm)
Stock
24.0
24.5
25.0
25.5
26.0
26.5
27.0
27.5
28.0
28.5
29.0
29.5
30.0
30.5
31.0
31.5
32.0
32.5
33.0
33.5
34.0
34.5
35.0
35.5
36.0
36.5
37.0
37.5
38.0
38.5
39.0
39.5
40.0
BRA2400S32
BRA2450S32
BRA2500S32
BRA2550S32
BRA2600S32
BRA2650S32
BRA2700S32
BRA2750S32
BRA2800S32
BRA2850S32
BRA2900S32
BRA2950S32
BRA3000S32
BRA3050S32
BRA3100S40
BRA3150S40
BRA3200S40
BRA3250S40
BRA3300S40
BRA3350S40
BRA3400S40
BRA3450S40
BRA3500S40
BRA3550S40
BRA3600S40
BRA3650S40
BRA3700S40
BRA3750S40
BRA3800S40
BRA3850S40
BRA3900S40
BRA3950S40
BRA4000S40
a
a
a
a
a
a
a
a
a
a
a
a
a
a
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
Order Number
23.5<DC<24.5
24.5<DC<25.5
25.5<DC<26.5
26.5<DC<27.5
BRArrrrS32
27.5<DC<28.5
LU
LH OAL LF
PL DCON
90.2 114.2 174.2 171

90.3 114.3 174.3 171
3.2
3.3
32
32
89.3 114.3 174.3 171
3.3
32
89.4 114.4 174.4 171
3.4
32
93.5 119.5 179.5 176
3.5
32
93.6 119.6 179.6 176
3.6
32
92.6 119.6 179.6 176
3.6
32
92.7 119.7 179.7 176
3.7
32
96.8 124.8 184.8 181
3.8
32
96.8 124.8 184.8 181
3.8
32
100.9 129.9 189.9 186
3.9
32
101.0 130.0 190.0 186
4.0
32
29.5<DC<30.5
100.0 130.0 190.0 186

100.1 130.1 190.1 186
4.0
4.1
32
32
30.5<DC<31.5
100.2 131.2 201.2 197

100.2 131.2 201.2 197
4.2
4.2
40
40
104.3 136.3 206.3 202
4.3
40
104.4 136.4 206.4 202
4.4
40
108.4 141.4 211.4 207
4.4
40
108.5 141.5 211.5 207
4.5
40
107.6 141.6 211.6 207
4.6
40
107.6 141.6 211.6 207
4.6
40
111.7 146.7 216.7 212
4.7
40
28.5<DC<29.5
31.5<DC<32.5
32.5<DC<33.5
33.5<DC<34.5
34.5<DC<35.5
35.5<DC<36.5
36.5<DC<37.5
37.5<DC<38.5
38.5<DC<39.5
39.5<DC<40.0
BRArrrrS40
111.8 146.8 216.8 212
4.8
40
115.8 151.8 221.8 217
4.8
40
115.9 151.9 221.9 217
4.9
40
120.0 157.0 227.0 222
5.0
40
120.0 157.0 227.0 222
5.0
40
124.1 162.1 232.1 227
5.1
40
124.2 162.2 232.2 227
5.2
40
123.2 162.2 232.2 227
5.2
40
123.3 162.3 232.3 227

127.4 167.4 237.4 232
5.3
5.4
40
40
(Note 1) Drills in the intermediate drill diameter range are produced to order only.
(Note 2) For ordering an intermediate diameter, please enter the diameter (DC) into the 4-digit spacerrrrin the nominal designation.
(Ex. UP20M BRAr
2r
5r
3r
(Note 3) Please contact us regarding special designs.
(Note 4) Please contact us for any geometry that is not in this catalogue (e.g. drills with chamfered cutting edges can be made to order).
CUTTING CONDITIONS
TECHNICAL DATA
N210
Q001
DRILLING
Order Number
UP20M
DC
(mm)
N207
CARBIDE
BRL
P
Steel

aEasy regrinding.
aUnique flute shape for lathes.
8 < DC < 10
10<DC < 18
18<DC < 30
30<DC < 40
0
0.015
0
0.018
0
0.021
0
0.025
a For turning
(I/d=3)
DCON
LF
150
DC(h7)
PL
LU
LH
OAL
Standard Diameter
DRILLING
N208
Dimensions (mm)
Order Number
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
12.5
13.0
13.5
14.0
14.5
15.0
15.5
16.0
16.5
17.0
17.5
18.0
18.5
19.0
19.5
20.0
20.5
21.0
21.5
22.0
22.5
23.0
23.5
BRL0800S16
BRL0850S16
BRL0900S16
BRL0950S16
BRL1000S16
BRL1050S16
BRL1100S16
BRL1150S16
BRL1200S16
BRL1250S16
BRL1300S16
BRL1350S16
BRL1400S16
BRL1450S16
BRL1500S20
BRL1550S20
BRL1600S20
BRL1650S20
BRL1700S20
BRL1750S20
BRL1800S20
BRL1850S20
BRL1900S25
BRL1950S25
BRL2000S25
BRL2050S25
BRL2100S25
BRL2150S25
BRL2200S25
BRL2250S25
BRL2300S25
BRL2350S25
STi40T
Stock
DC
(mm)
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
LU
LH OAL LF
PL DCON
24.1
24.1
36.1 84.1
36.1 84.1
83
83
1.1
1.1
16
16
29.2
41.2 89.2
88
1.2
16
29.3
41.3 89.3
88
1.3
16
36.3
46.3 94.3
93
1.3
16
36.4
46.4 94.4
93
1.4
16
41.5
52.5 100.5
99
1.5
16
41.5
52.5 100.5
99
1.5
16
45.6
57.6 105.6 104
1.6
16
45.7
57.7 105.7 104
1.7
16
49.7
62.7 110.7 109
1.7
16
49.8
62.8 110.8 109
1.8
16
13.5<DC < 14.5
53.9
53.9
67.9 115.9 114

67.9 115.9 114
1.9
1.9
16
16
14.5<DC < 15.5
63.0
63.1
78.0 128.0 126

78.1 128.1 126
2.0
2.1
20
20
67.1
83.1 133.1 131
2.1
20
67.2
83.2 133.2 131
2.2
20
71.3
88.3 138.3 136
2.3
20
71.3
88.3 138.3 136
2.3
20
17.5<DC < 18.5
75.4
75.5
93.4 143.4 141

93.5 143.5 141
2.4
2.5
20
20
18.5<DC < 19.5
79.5 103.5 159.5 157

79.6 103.6 159.6 157
2.5
2.6
25
25
83.7 103.7 159.7 157
2.7
25
83.7 103.7 159.7 157
2.7
25
82.8 103.8 159.8 157
2.8
25
82.9 103.9 159.9 157
2.9
25
86.9 108.9 164.9 162
2.9
25
87.0 109.0 165.0 162
3.0
25
86.1 109.1 165.1 162

86.1 109.1 165.1 162
3.1
3.1
25
25
Order Number
8.0 < DC < 8.5

8.5<DC < 9.5
9.5<DC < 10.5
10.5<DC < 11.5
BRLrrrrS16
11.5<DC < 12.5

12.5<DC < 13.5
15.5<DC < 16.5
BRLrrrrS20
16.5<DC < 17.5
19.5<DC < 20.5

20.5<DC < 21.5
BRLrrrrS25
21.5<DC < 22.5

22.5<DC < 23.5
CARBIDE
Standard Diameter
Dimensions (mm)
Stock
24.0
24.5
25.0
25.5
26.0
26.5
27.0
27.5
28.0
28.5
29.0
29.5
30.0
30.5
31.0
31.5
32.0
32.5
33.0
33.5
34.0
34.5
35.0
35.5
36.0
36.5
37.0
37.5
38.0
38.5
39.0
39.5
40.0
BRL2400S32
BRL2450S32
BRL2500S32
BRL2550S32
BRL2600S32
BRL2650S32
BRL2700S32
BRL2750S32
BRL2800S32
BRL2850S32
BRL2900S32
BRL2950S32
BRL3000S32
BRL3050S32
BRL3100S40
BRL3150S40
BRL3200S40
BRL3250S40
BRL3300S40
BRL3350S40
BRL3400S40
BRL3450S40
BRL3500S40
BRL3550S40
BRL3600S40
BRL3650S40
BRL3700S40
BRL3750S40
BRL3800S40
BRL3850S40
BRL3900S40
BRL3950S40
BRL4000S40
a
a
a
a
a
a
a
a
a
a
a
a
a
a
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
r
Order Number
23.5<DC < 24.5

24.5<DC < 25.5
25.5<DC < 26.5
26.5<DC < 27.5
BRLrrrrS32
27.5<DC < 28.5
LU
LH OAL LF
PL DCON
90.2 114.2 174.2 171

90.3 114.3 174.3 171
3.2
3.3
32
32
89.3 114.3 174.3 171
3.3
32
89.4 114.4 174.4 171
3.4
32
93.5 119.5 179.5 176
3.5
32
93.6 119.6 179.6 176
3.6
32
92.6 119.6 179.6 176
3.6
32
92.7 119.7 179.7 176
3.7
32
96.8 124.8 184.8 181
3.8
32
96.8 124.8 184.8 181
3.8
32
100.9 129.9 189.9 186
3.9
32
101.0 130.0 190.0 186
4.0
32
29.5<DC < 30.5
100.0 130.0 190.0 186

100.1 130.1 190.1 186
4.0
4.1
32
32
30.5<DC < 31.5
100.2 131.2 201.2 197

100.2 131.2 201.2 197
4.2
4.2
40
40
104.3 136.3 206.3 202
4.3
40
104.4 136.4 206.4 202
4.4
40
108.4 141.4 211.4 207
4.4
40
108.5 141.5 211.5 207
4.5
40
107.6 141.6 211.6 207
4.6
40
107.6 141.6 211.6 207
4.6
40
111.7 146.7 216.7 212
4.7
40
28.5<DC < 29.5
31.5<DC < 32.5

32.5<DC < 33.5
33.5<DC < 34.5
34.5<DC < 35.5
35.5<DC < 36.5
36.5<DC < 37.5
37.5<DC < 38.5
38.5<DC < 39.5
39.5<DC < 40.0
BRLrrrrS40
111.8 146.8 216.8 212
4.8
40
115.8 151.8 221.8 217
4.8
40
115.9 151.9 221.9 217
4.9
40
120.0 157.0 227.0 222
5.0
40
120.0 157.0 227.0 222
5.0
40
124.1 162.1 232.1 227
5.1
40
124.2 162.2 232.2 227
5.2
40
123.2 162.2 232.2 227
5.2
40
123.3 162.3 232.3 227

127.4 167.4 237.4 232
5.3
5.4
40
40
(Note 1) Drills in the intermediate drill diameter range are produced to order only.
(Note 2) For ordering an intermediate diameter, please enter the diameter (DC) into the 4-digit spacerrrrin the nominal designation.
(Ex. STi40T BRLr
2r
5r
3r
(Note 3) Please contact us regarding special designs.
(Note 4) Please contact us for any geometry that is not in this catalogue (e.g. drills with chamfered cutting edges can be made to order).
CUTTING CONDITIONS
TECHNICAL DATA
N210
Q001
DRILLING
Order Number
STi40T
DC
(mm)
N209
CARBIDE
BRA/BRL
Type

Work Material
Hardness
Feed
(mm/rev)
Drill Diameter > &18.0

Cutting Speed
(m/min)
Feed
(mm/rev)
< 180HB
55 (40 65)
0.25 (0.20 0.30)
65 (50 75)
0.30 (0.25 0.35)
75 (60 85)
0.30 (0.25 0.35)
Carbon Steel
Alloy Steel
180 280HB
50 (35 60)
0.25 (0.20 0.30)
60 (45 70)
0.30 (0.25 0.35)
70 (55 80)
0.30 (0.25 0.35)
280 350HB
40 (30 50)
0.25 (0.20 0.30)
50 (40 60)
0.25 (0.20 0.30)
55 (45 65)
0.27 (0.20 0.30)
< 200HB
30 (20 40)
0.25 (0.20 0.27)
35 (25 45)
0.27 (0.20 0.30)
40 (30 50)
0.30 (0.25 0.35)
K Gray Cast Iron Tensile Strength < 350MPa 60 (40 70)
0.30 (0.25 0.35)
70 (50 80)
0.35 (0.30 0.40)
80 (60 90)
0.40 (0.35 0.45)
Ductile Cast Iron Tensile Strength < 450MPa 55 (40 65)
0.27 (0.20 0.30)
60 (45 70)
0.30 (0.25 0.35)
70 (55 80)
0.30 (0.25 0.35)
15 (10 20)
0.10 (0.05 0.12)
20 (15 25)
0.15 (0.10 0.20)
25 (20 30)
0.15 (0.10 0.20)
Titanium Alloy
20 (10 25)
0.15 (0.10 0.17)
30 (20 35)
0.20 (0.15 0.25)
35 (30 40)
0.25 (0.20 0.30)
Mild Steel
< 180HB
50 (35 60)
0.25 (0.20 0.30)
60 (45 70)
0.30 (0.25 0.35)
65 (50 75)
0.30 (0.25 0.35)
S Heat Resistant Alloy

P
Carbon Steel
Alloy Steel
180 280HB
45 (30 55)
0.25 (0.20 0.30)
55 (40 65)
0.30 (0.25 0.35)
60 (45 70)
0.30 (0.25 0.35)
280 350HB
35 (25 45)
0.25 (0.20 0.30)
45 (35 55)
0.25 (0.20 0.30)
50 (40 60)
0.27 (0.20 0.30)
< 200HB
30 (20 40)
0.25 (0.20 0.27)
30 (20 40)
0.27 (0.20 0.30)
35 (25 45)
0.30 (0.25 0.35)
K Gray Cast Iron Tensile Strength < 350MPa 55 (40 70)
0.30 (0.25 0.35)
60 (45 75)
0.35 (0.3 0.40)
65 (50 80)
0.40 (0.35 0.45)
Ductile Cast Iron Tensile Strength < 450MPa 50 (35 60)
0.27 (0.20 0.30)
55 (40 65)
0.30 (0.25 0.35)
60 (45 70)
0.30 (0.25 0.35)
15 (10 20)
0.10 (0.05 0.12)
15 (10 20)
0.15 (0.10 0.20)
20 (15 25)
0.15 (0.10 0.20)
20 (10 25)
0.15 (0.10 0.17)
25 (10 30)
0.20 (0.15 0.25)
30 (20 35)
0.25 (0.20 0.30)
M Stainless Steel
B
R
L
Drill Diameter & 13.0 & 18.0

Cutting Speed
(m/min)
Feed
(mm/rev)
Mild Steel
B M Stainless Steel
R
A
Drill Diameter & 8.0 & 13.0

Cutting Speed
(m/min)
S Heat Resistant Alloy

Titanium Alloy
Workpiece : JIS SCM440(200HB) Cutting Speed : 60m/min
Torque
16000
16
ev
14
.5
f=0
/rev
4mm
f=0.
ev
mm/r
f=0.3
12
10
8
ev
0.2mm/r
f=
v
f=0.1mm/re
2
0
14000
/r
mm
Torque (N cm)
Power Consumption
10
15
20
25
30
35
/rev
4mm
f=0.
ev
mm/r
f=0.3
ev
/r
m
f=0.2m /rev
m
f=0.1m
10000
8000
6000
4000
2000
40
Drill Diameter (mm)
10
15
20
25
30
Drill Diameter (mm)
a Reason for Low Thrust Load
DRILLING
Thrust
BRA/BRL
16000
14000
Thrust (N)
ev
mm/r
10000
f=0.4
8000
m/rev
f=0.3m
6000
Thrust(N)
f=0.2mm/rev
f=0.1mm/rev
4000
2000
0
ev
m/r
.5m
f=0
12000
Conventional Drill
10
15
20
25
30
35
40
Drill Diameter (mm)
Thrust(N)
N210
/rev
mm
.5
f=0
12000
35
40
CARBIDE
y IDENTIFICATION
BRA
FOR BRA AND BRL
2500
S32
zDrill Type
H
x
xShank Size
Shank Diameter (DCON)
Drill Size
Drill Diameter (DC)
cHoning Type
zDrill Type
Type
Description
Point
Relief
Angle Hole Depth Helix Angle Angle
BRA
BRL
l/d=3 4
150
l/d=3 4
150
20
10+
Straight
10
10
Back Taper
Applications
Body Dia.
Products Name
General Use
0.3mm/100mm DC-0.2mm (CarbonFor
/ Alloy / Stainless Steel)
1.0mm/100mm DC-1.0mm
For Turning
BRAppppSpp
BRLppppSppL
xShank Size
Type
Shank Diameter
Drill Diameter
S16
16 (h6)
8.0 < DC< 14.5
S20
20 (h6)
14.5 < DC< 18.5
S25
25 (h6)
18.5 < DC< 23.5
S32
32 (h6)
23.5 < DC< 30.5
S40
40 (h6)
30.5 < DC< 40.0
cHoning Type
Honing Width
(mm)
BRA
BRL
-(Standard)
0.150.2
Carbon Steel, Alloy Steel, Mild Steel
Carbon Steel ( > 200HB), Alloy Steel, Stainless Steel
Carbon Steel (<200HB)
0.250.3
High Tension Steel, Rolled Steel for Welded Structures
0.30.4
Mild Steel
0.20.25
0.050.1
Stainless Steel, Heat Resistant Alloy, Titanium Alloy
0.0250.08
Cast Iron, Aluminium Alloy, Non-Ferrous Metals
Cast Iron
DRILLING
Work Material
Type
N211
DRILLING(INDEXABLE TYPE)
MVX
P
Steel
a Ideal combination of outer CVD insert and inner PVD insert.

a High rigidity body that enabled L/D=6 deep hole machining.
Machining tolerance(guide)(mm)
L/D
2D, 3D
4D, 5D
33.547
4863
0
+ 0.25
0
+ 0.35
0
+ 0.45
0
+ 0.3
0
+ 0.4
0
+ 0.6
0
+ 0.3
0
+ 0.45
DC
DCON
6D
1733
LU
DCSFMS
CARBIDE
LPR
OAL
Maximum offset for turning
Tighten the clamp screw according to the torque below.
X axis plus
Drill Diameter (mm)
Centre Axis
17 19.5
20 22.5
23 27.5
28 46
47 63
(mm)
(l/d)
2
3
17.0
4
5
6
2
3
17.5
4
5
6
2
3
18.0
4
5
6
2
3
18.5
DRILLING
5
6
2
3
19.0
4
5
6
2
3
19.5
4
5
6
N212
Order Number
Stock
DC
Hole
Depth
MVX1700X2F20
MVX1700X3F20
MVX1700X4F20
MVX1700X5F20
MVX1700X6F20
MVX1750X2F25
MVX1750X3F25
MVX1750X4F25
MVX1750X5F25
MVX1750X6F25
MVX1800X2F25
MVX1800X3F25
MVX1800X4F25
MVX1800X5F25
MVX1800X6F25
MVX1850X2F25
MVX1850X3F25
MVX1850X4F25
MVX1850X5F25
MVX1850X6F25
MVX1900X2F25
MVX1900X3F25
MVX1900X4F25
MVX1900X5F25
MVX1900X6F25
MVX1950X2F25
MVX1950X3F25
MVX1950X4F25
MVX1950X5F25
MVX1950X6F25
Number of Teeth
A
LU
OAL
DCON DCSFMS
(mm)
41
58
56
73
99
116
20
20
25
25
0.5
0.5
75
90
133
20
25
0.5
2
2
92
109
107
124
150
167
20
20
25
25
0.5
0.5
2
2
42
59.5
62
79.5
112
129.5
25
25
32
32
0.45
0.45
77
97
147
25
32
0.45
2
2
94.5
112
114.5
132
164.5
182
25
25
32
32
0.45
0.45
2
2
43
61
63
81
113
131
25
25
32
32
0.4
0.4
79
99
149
25
32
0.4
2
2
97
115
117
135
167
185
25
25
32
32
0.4
0.4
114
132.5
25
25
32
32
0.35
0.35
101
151
25
32
0.35
169.5
188
25
25
32
32
0.35
0.35
115
134
25
25
32
32
0.3
0.3
a
a
2
2
44
62.5
81
2
2
99.5
118
119.5
138
2
2
45
64
65
84
83
103
153
25
32
0.3
2
2
102
121
122
141
172
191
25
25
32
32
0.3
0.3
116
135.5
25
25
32
32
0.25
0.25
a
a
2
2
85
2
2
104.5
124
46
65.5
Clamp Torque (N m) : TPS25=1.0, TPS3=2.0
LPR
2
2
1.0
2.0
2.5
3.5
7.5
Dimensions (mm)
Clamp Torque (N m)
64
82.5
66
85.5
105
155
25
32
0.25
124.5
144
174.5
194
25
25
32
32
0.25
0.25
Insert Number
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
SOMX063005-oo
Clamp Screw
Wrench
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
TPS25
TIP07F
20.0
4
5
6
20.5
2
3
2
3
21.0
4
5
6
21.5
2
3
2
3
22.0
4
5
6
22.5
2
3
2
3
23.0
4
5
6
23.5
2
3
2
3
24.0
4
5
6
24.5
2
3
2
3
25.0
4
5
6
25.5
2
3
2
3
26.0
4
5
6
MVX2000X2F25
MVX2000X3F25
MVX2000X4F25
MVX2000X5F25
MVX2000X6F25
MVX2050X2F25
MVX2050X3F25
MVX2100X2F25
MVX2100X3F25
MVX2100X4F25
MVX2100X5F25
MVX2100X6F25
MVX2150X2F25
MVX2150X3F25
MVX2200X2F25
MVX2200X3F25
MVX2200X4F25
MVX2200X5F25
MVX2200X6F25
MVX2250X2F25
MVX2250X3F25
MVX2300X2F25
MVX2300X3F25
MVX2300X4F25
MVX2300X5F25
MVX2300X6F25
MVX2350X2F25
MVX2350X3F25
MVX2400X2F25
MVX2400X3F25
MVX2400X4F25
MVX2400X5F25
MVX2400X6F25
MVX2450X2F25
MVX2450X3F25
MVX2500X2F25
MVX2500X3F25
MVX2500X4F25
MVX2500X5F25
MVX2500X6F25
MVX2550X2F25
MVX2550X3F25
MVX2600X2F32
MVX2600X3F32
MVX2600X4F32
MVX2600X5F32
MVX2600X6F32
A
LPR
OAL
2
2
47
67
67
87
117
137
25
25
32
32
0.6
0.6
87
107
157
25
32
0.6
2
2
107
127
127
147
177
197
25
25
32
32
0.6
0.6
DCON DCSFMS
Clamp Screw
2
2
48
68.5
68
88.5
118
138.5
25
25
32
32
0.55
0.55
2
2
49
70
69
90
119
140
25
25
32
32
0.5
0.5
91
111
161
25
32
0.5
2
2
112
133
132
153
182
203
25
25
32
32
0.5
0.5
a
a
a
2
2
50
71.5
70
91.5
120
141.5
25
25
32
32
0.45
0.45
2
2
51
73
71
93
121
143
25
25
32
32
0.4
0.4
95
115
165
25
32
0.4
2
2
117
139
137
159
187
209
25
25
32
32
0.4
0.4
a
a
a
2
2
52
74.5
72
94.5
122
144.5
25
25
32
32
0.35
0.35
2
2
53
76
73
96
123
146
25
25
32
32
0.8
0.8
99
119
169
25
32
0.8
2
2
122
145
142
165
192
215
25
25
32
32
0.8
0.8
a
a
a
2
2
54
77.5
74
97.5
124
147.5
25
25
32
32
0.75
0.75
2
2
55
79
75
99
125
149
25
25
32
32
0.7
0.7
103
123
173
25
32
0.7
2
2
127
151
147
171
197
221
25
25
32
32
0.7
0.7
a
a
a
2
2
56
80.5
76
100.5
126
150.5
25
25
32
32
0.65
0.65
2
2
57
82
77
102
127
152
25
25
32
32
0.6
0.6
107
127
177
25
32
0.6
2
2
132
157
152
177
202
227
25
25
32
32
0.6
0.6
a
a
a
2
2
58
83.5
78
103.5
128
153.5
25
25
32
32
0.6
0.6
2
2
59
85
79
105
134
160
32
32
42
42
0.5
0.5
111
131
186
32
42
0.5
2
2
137
163
157
183
212
238
32
32
42
42
0.5
0.5
a
a
a
Insert Number
(mm)
LU
(l/d)
2
3
Dimensions (mm)
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX073505-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
Wrench
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS3
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
DRILLING
(mm)
Order Number
Stock
DC
Hole
Depth
Number of Teeth
CARBIDE
INSERT DESCRIPTION
CUTTING CONDITIONS
N218
N218
USAGE NOTE
N247
TECHNICAL DATA
Q001
N213
(mm)
(l/d)
26.5
2
3
2
3
27.0
4
5
6
27.5
2
3
2
3
28.0
4
5
6
28.5
2
3
2
3
29.0
4
5
6
29.5
2
3
2
3
30.0
4
5
6
30.5
3
2
3
31.0
4
5
6
31.5
3
2
3
DRILLING
32.0
4
5
6
32.5
3
2
3
33.0
4
5
6
MVX2650X2F32
MVX2650X3F32
MVX2700X2F32
MVX2700X3F32
MVX2700X4F32
MVX2700X5F32
MVX2700X6F32
MVX2750X2F32
MVX2750X3F32
MVX2800X2F32
MVX2800X3F32
MVX2800X4F32
MVX2800X5F32
MVX2800X6F32
MVX2850X2F32
MVX2850X3F32
MVX2900X2F32
MVX2900X3F32
MVX2900X4F32
MVX2900X5F32
MVX2900X6F32
MVX2950X2F32
MVX2950X3F32
MVX3000X2F32
MVX3000X3F32
MVX3000X4F32
MVX3000X5F32
MVX3000X6F32
MVX3050X3F32
MVX3100X2F40
MVX3100X3F40
MVX3100X4F40
MVX3100X5F40
MVX3100X6F40
MVX3150X3F40
MVX3200X2F40
MVX3200X3F40
MVX3200X4F40
MVX3200X5F40
MVX3200X6F40
MVX3250X3F40
MVX3300X2F40
MVX3300X3F40
MVX3300X4F40
MVX3300X5F40
MVX3300X6F40
Dimensions (mm)
A
LU
LPR
OAL
DCON DCSFMS
(mm)
2
2
60
86.5
80
106.5
135
161.5
32
32
42
42
0.5
0.5
2
2
61
88
81
108
136
163
32
32
42
42
0.45
0.45
115
135
190
32
42
0.45
2
2
142
169
162
189
217
244
32
32
42
42
0.45
0.45
a
a
a
2
2
62
89.5
82
109.5
137
164.5
32
32
42
42
0.4
0.4
2
2
63
91
83
111
138
166
32
32
42
42
0.85
0.85
119
139
194
32
42
0.85
2
2
147
175
167
195
222
250
32
32
42
42
0.85
0.85
a
a
a
2
2
64
92.5
84
112.5
139
167.5
32
32
42
42
0.8
0.8
2
2
65
94
85
114
140
169
32
32
42
42
0.75
0.75
123
143
198
32
42
0.75
2
2
152
181
172
201
227
256
32
32
42
42
0.75
0.75
a
a
a
2
2
66
95.5
86
115.5
141
170.5
32
32
42
42
0.7
0.7
2
2
67
97
87
117
142
172
32
32
42
42
0.65
0.65
127
147
202
32
42
0.65
a
a
2
2
157
187
177
207
232
262
32
32
42
42
0.65
0.65
118.5
173.5
32
42
0.6
a
a
2
2
69
100
89
120
154
185
40
40
50
50
0.55
0.55
131
151
216
40
50
0.55
a
a
2
2
162
193
182
213
247
278
40
40
50
50
0.55
0.55
101.5
121.5
186.5
40
50
0.55
a
a
2
2
71
103
91
123
156
188
40
40
50
50
0.45
0.45
135
155
220
40
50
0.45
a
a
2
2
167
199
187
219
252
284
40
40
50
50
0.45
0.45
104.5
124.5
189.5
40
50
0.45
a
a
2
2
73
106
93
126
158
191
40
40
50
50
0.4
0.4
139
159
224
40
50
0.4
2
2
172
205
192
225
257
290
40
40
50
50
0.4
0.4
a
a
a
98.5
N214
Order Number
Stock
DC
Hole
Depth
Number of Teeth
MVX
CARBIDE
Insert Number
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX084005-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
SOMX094506-oo
Clamp Screw
Wrench
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS351
TIP10W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
TPS4
TIP15W
CARBIDE
3
2
3
34.0
4
5
6
34.5
3
2
3
35.0
4
5
6
35.5
3
2
3
36.0
4
5
6
2
3
37.0
4
5
6
2
3
38.0
4
5
6
2
3
39.0
4
5
6
2
3
40.0
4
5
6
2
3
41.0
4
5
6
2
3
42.0
4
5
6
MVX3350X3F40
MVX3400X2F40
MVX3400X3F40
MVX3400X4F40
MVX3400X5F40
MVX3400X6F40
MVX3450X3F40
MVX3500X2F40
MVX3500X3F40
MVX3500X4F40
MVX3500X5F40
MVX3500X6F40
MVX3550X3F40
MVX3600X2F40
MVX3600X3F40
MVX3600X4F40
MVX3600X5F40
MVX3600X6F40
MVX3700X2F40
MVX3700X3F40
MVX3700X4F40
MVX3700X5F40
MVX3700X6F40
MVX3800X2F40
MVX3800X3F40
MVX3800X4F40
MVX3800X5F40
MVX3800X6F40
MVX3900X2F40
MVX3900X3F40
MVX3900X4F40
MVX3900X5F40
MVX3900X6F40
MVX4000X2F40
MVX4000X3F40
MVX4000X4F40
MVX4000X5F40
MVX4000X6F40
MVX4100X2F40
MVX4100X3F40
MVX4100X4F40
MVX4100X5F40
MVX4100X6F40
MVX4200X2F40
MVX4200X3F40
MVX4200X4F50
MVX4200X5F50
MVX4200X6F50
107.5
127.5
192.5
40
50
1.2
a
a
2
2
75
109
105
139
170
204
40
40
50
50
1.1
1.1
143
173
238
40
50
1.1
a
a
2
2
177
211
207
241
272
306
40
40
50
50
1.1
1.1
110.5
140.5
205.5
40
50
1.1
a
a
2
2
77
112
107
142
172
207
40
40
50
50
1.0
1.0
147
177
242
40
50
1.0
a
a
2
2
182
217
212
247
277
312
40
40
50
50
1.0
1.0
113.5
143.5
208.5
40
50
1.0
a
a
2
2
79
115
109
145
174
210
40
40
50
50
1.0
1.0
151
181
246
40
50
1.0
2
2
187
223
217
253
282
318
40
40
50
50
1.0
0.9
2
2
81
118
111
148
176
213
40
40
50
50
0.9
0.9
155
185
250
40
50
0.9
2
2
192
229
222
259
287
324
40
40
50
50
0.9
0.9
2
2
83
121
113
151
178
216
40
40
50
50
0.8
0.8
159
189
254
40
50
0.8
2
2
197
235
227
265
292
330
40
40
50
50
0.8
0.8
2
2
85
124
115
154
180
219
40
40
50
50
0.7
0.7
163
193
258
40
50
0.7
2
2
202
241
232
271
297
336
40
40
50
50
0.7
0.7
2
2
87
127
117
157
182
222
40
40
50
50
1.5
1.5
167
197
262
40
50
1.5
2
2
207
247
237
277
302
342
40
40
50
50
1.5
1.4
2
2
89
130
119
160
184
225
40
40
50
50
1.4
1.4
171
201
266
40
50
1.4
2
2
212
253
242
283
307
348
40
40
50
50
1.4
1.4
2
2
91
133
121
163
186
228
40
40
50
50
1.3
1.3
175
205
280
50
63
1.3
2
2
217
259
247
289
322
364
50
50
63
63
1.3
1.3
a
a
a
a
a
a
a
a
a
a
a
a
A
LU
LPR
OAL
DCON DCSFMS
(mm)
Insert Number
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX115506-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
Clamp Screw
Wrench
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
TPS43
TIP15W
DRILLING
(l/d)
Stock
(mm)
33.5
Order Number
Dimensions (mm)
Number of Teeth
DC
Hole
Depth
INSERT DESCRIPTION
CUTTING CONDITIONS
USAGE NOTE
TECHNICAL DATA
N218
N218
N247
Q001
N215
DC
(mm)
Hole
Depth
(l/d)
2
3
43.0
4
5
6
44.0
45.0
46.0
47.0
48.0
49.0
50.0
DRILLING
51.0
52.0
53.0
Order Number
Stock
MVX
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
MVX4300X2F40
MVX4300X3F40
MVX4300X4F50
MVX4300X5F50
MVX4300X6F50
MVX4400X2F40
MVX4400X3F40
MVX4400X4F50
MVX4400X5F50
MVX4500X2F40
MVX4500X3F40
MVX4500X4F50
MVX4500X5F50
MVX4600X2F40
MVX4600X3F40
MVX4600X4F50
MVX4600X5F50
MVX4700X2F40
MVX4700X3F40
MVX4700X4F50
MVX4700X5F50
MVX4800X2F40
MVX4800X3F40
MVX4800X4F50
MVX4800X5F50
MVX4900X2F40
MVX4900X3F40
MVX4900X4F50
MVX4900X5F50
MVX5000X2F40
MVX5000X3F40
MVX5000X4F50
MVX5000X5F50
MVX5100X2F40
MVX5100X3F40
MVX5100X4F50
MVX5100X5F50
MVX5200X2F40
MVX5200X3F40
MVX5200X4F50
MVX5200X5F50
MVX5300X2F40
MVX5300X3F40
MVX5300X4F50
MVX5300X5F50
Number of Teeth
CARBIDE
Dimensions (mm)
A
LU
N216
LPR
OAL
DCON DCSFMS
(mm)
2
2
93
136
123
166
188
231
40
40
50
50
1.2
1.2
179
209
284
50
63
1.2
2
2
222
265
252
295
327
370
50
50
63
63
1.2
1.2
2
2
95
139
125
169
190
234
40
40
50
50
1.1
1.1
2
2
183
227
213
257
288
332
50
50
63
63
1.1
1.1
2
2
97
142
127
172
192
237
40
40
50
50
1.0
1.0
2
2
187
232
217
262
292
337
50
50
63
63
1.0
1.0
2
2
99
145
129
175
194
240
40
40
50
50
0.9
0.9
2
2
191
237
221
267
296
342
50
50
63
63
0.9
0.9
2
2
101
148
141
188
206
253
40
40
63
63
1.9
1.9
2
2
195
242
235
282
310
357
50
50
63
63
1.9
1.9
2
2
103
151
143
191
208
256
40
40
63
63
1.8
1.8
2
2
199
247
239
287
314
362
50
50
63
63
1.8
1.8
2
2
105
154
145
194
210
259
40
40
63
63
1.7
1.7
2
2
203
252
243
292
318
367
50
50
63
63
1.7
1.7
2
2
107
157
147
197
212
262
40
40
63
63
1.6
1.6
2
2
207
257
247
297
322
372
50
50
63
63
1.6
1.6
2
2
109
160
149
200
214
265
40
40
63
63
1.5
1.5
2
2
211
262
251
302
326
377
50
50
63
63
1.5
1.5
2
2
111
163
151
203
216
268
40
40
63
63
1.4
1.4
2
2
215
267
255
307
330
382
50
50
63
63
1.4
1.4
2
2
113
166
153
206
218
271
40
40
63
63
1.3
1.3
2
2
219
272
259
312
334
387
50
50
63
63
1.3
1.3
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Insert Number
Clamp Screw
* Clamp Torque (N m) : TPS43=3.5, TPS54=4.5
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX136008-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
Wrench
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS43 zTIP15W
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
TPS54 xTIP25D
CARBIDE
56.0
57.0
58.0
59.0
60.0
61.0
62.0
63.0
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
MVX5400X2F40
MVX5400X3F40
MVX5400X4F50
MVX5400X5F50
MVX5500X2F40
MVX5500X3F40
MVX5500X4F50
MVX5500X5F50
MVX5600X2F40
MVX5600X3F40
MVX5600X4F50
MVX5600X5F50
MVX5700X2F40
MVX5700X3F40
MVX5700X4F50
MVX5700X5F50
MVX5800X2F40
MVX5800X3F40
MVX5800X4F50
MVX5800X5F50
MVX5900X2F40
MVX5900X3F40
MVX5900X4F50
MVX5900X5F50
MVX6000X2F40
MVX6000X3F40
MVX6000X4F50
MVX6000X5F50
MVX6100X2F40
MVX6100X3F40
MVX6100X4F50
MVX6100X5F50
MVX6200X2F40
MVX6200X3F40
MVX6200X4F50
MVX6200X5F50
MVX6300X2F40
MVX6300X3F40
MVX6300X4F50
MVX6300X5F50
115
155
220
40
63
1.2
169
209
274
40
63
1.2
2
2
223
277
263
317
338
392
50
50
63
63
1.2
1.2
2
2
117
172
157
212
222
277
40
40
63
63
1.1
1.1
2
2
227
282
267
322
342
397
50
50
63
63
1.1
1.1
2
2
119
175
159
215
224
280
40
40
63
63
1.0
1.0
2
2
231
287
271
327
346
402
50
50
63
63
1.0
1.0
2
2
121
178
161
218
226
283
40
40
68
68
1.5
1.5
2
2
235
292
275
332
350
407
50
50
68
68
1.5
1.5
2
2
123
181
163
221
228
286
40
40
68
68
1.4
1.4
2
2
239
297
279
337
354
412
50
50
68
68
1.4
1.4
2
2
125
184
165
224
230
289
40
40
68
68
1.3
1.3
2
2
243
302
283
342
358
417
50
50
68
68
1.3
1.3
2
2
127
187
167
227
232
292
40
40
68
68
1.2
1.2
2
2
247
307
287
347
362
422
50
50
68
68
1.2
1.2
2
2
129
190
169
230
234
295
40
40
68
68
1.1
1.1
2
2
251
312
291
352
366
427
50
50
68
68
1.1
1.1
2
2
131
193
171
233
236
298
40
40
68
68
1.0
1.0
2
2
255
317
295
357
370
432
50
50
68
68
1.0
1.0
2
2
133
196
173
236
238
301
40
40
68
68
0.8
0.8
2
2
259
322
299
362
374
437
50
50
68
68
0.8
0.8
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
A
LU
LPR
OAL
DCON DCSFMS
(mm)
Insert Number
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX166508-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
SOMX187008-oo
Clamp Screw
Wrench
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
TPS54
TIP25D
INSERT DESCRIPTION
CUTTING CONDITIONS
USAGE NOTE
TECHNICAL DATA
N218
N218
N247
Q001
DRILLING
55.0
(l/d)
54.0
Stock
(mm)
Order Number
Dimensions (mm)
Number of Teeth
DC
Hole
Depth
N217
CARBIDE
MVX
INSERTS
Shape
Drill Dia.
UM
US
RE
17 19.5 SOMX063005-UM
0.5
20 22.5 SOMX073505-UM
3.5
0.5
23 27.5 SOMX084005-UM
8.3
0.5
SOMX094506-UM
9.7
4.5
0.6
33.5 39 SOMX115506-UM
11.6
5.5
0.6
SOMX136008-UM 13.8
0.8
47 56
SOMX166508-UM 16.5
6.5
0.8
57 63
SOMX187008-UM 18.2
0.8
0.5
20 22.5 SOMX073505-US
3.5
0.5
23 27.5 SOMX084005-US
8.3
0.5
SOMX094506-US
9.7
4.5
0.6
28 33
Geometry
VP15TF MC1020 MC5020
40 46
17 19.5 SOMX063005-US
For stainless steel inner edge
Stock
IC
28 33
General purpose
Dimensions (mm)
Insert Number
RE
11
S
IC
RE
11
IC
and MC5020 are made exclusively for use as an outer insert.

*MC1020
*US breaker is designed exclusively for use as an inner insert.

Work material
Hardness
Cutting Speed
Centre value
(Min.Max.)
(m/min)
l/d=26
DRILLING
l/d=2, 3
l/d=4, 5
l/d=6
l/d=2, 3
l/d=4, 5
l/d=6
180HB
200
(180235)
0.05
0.05
0.04
0.06
0.06
0.04
(0.040.06) (0.040.06) (0.040.05) (0.040.08) (0.040.07) (0.040.05)

(AISI 1045, AISI 4140etc.)
180 280HB
140
(115180)
0.08
(0.060.14)
0.08
0.05
(0.060.09) (0.040.06)
0.10
(0.060.18)
0.09
(0.060.12)
0.07
(0.060.08)

(AISI 4340etc.)
280 350HB
100
(75140)
0.08
(0.060.14)
0.08
0.05
(0.060.09) (0.040.06)
0.10
(0.060.18)
0.09
(0.060.12)
0.07
(0.060.08)
Alloy Tool Steel

(SKD, SKTetc.)
350HB
135
(100170)
0.08
(0.060.14)
0.08
0.05
(0.060.09) (0.040.06)
0.10
(0.060.18)
0.09
(0.060.12)
0.07
(0.060.08)

200HB
130
(80180)
0.08
(0.060.12)
0.06
0.05
(0.040.08) (0.040.06)
0.10
(0.060.14)
0.07
0.06
(0.060.08) (0.060.07)

(AISI 304LN, AISI 316LNetc.)
>200HB
130
(80180)
0.08
(0.060.12)
0.06
0.05
(0.040.08) (0.040.06)
0.10
(0.060.14)
0.07
0.06
(0.060.08) (0.060.07)

Stainless Steel
200HB
120
(80165)
0.08
(0.060.12)
0.06
0.05
(0.040.08) (0.040.06)
0.10
(0.060.14)
0.07
0.06
(0.060.08) (0.060.07)

Stainless Steel
(AISI 431, AISI 420J2etc.)
>200HB
120
(80165)
0.08
(0.060.12)
0.06
0.05
(0.040.08) (0.040.06)
0.10
(0.060.14)
0.07
0.06
(0.060.08) (0.060.07)
Gray Cast Iron

(FC300etc.)
Tensile Strength
160
(130195)
0.11
(0.080.14)
0.09
(0.080.10)
0.05
(0.040.06)
0.14
(0.100.18)
0.10
(0.100.12)
0.07
(0.060.08)
Ductile Cast Iron

(FCD450etc.)
Tensile Strength
100
(80135)
0.11
(0.080.14)
0.09
(0.080.10)
0.05
(0.040.06)
0.13
(0.100.16)
0.10
(0.100.11)
0.07
(0.060.08)
Ductile Cast Iron

(FCD700etc.)
Tensile Strength
100
(70125)
0.11
(0.080.14)
0.09
(0.080.10)
0.05
(0.040.06)
0.13
(0.100.16)
0.10
(0.100.11)
0.07
(0.060.08)
Note 1)
Note 2)
Note 3)
N218
&20&23.5
Feed per Tooth
Centre value (Min.Max.)
(mm/rev)
Mild Steel
(ASTM A36, AISI 1010etc.)
&17&19.5
Feed per Tooth
(mm/rev)
350MPa
450MPa
800MPa
Reduce the cutting speed by 30% when VP15TF is used as an outer insert.
L/D=3 is the recommended maximum depth when only external coolant is used.
Internal through coolant is highly necessary when drilling stainless steel.

Work material
Hardness
Cutting Speed
Centre value
(Min.Max.)
(m/min)
l/d=26
l/d=2, 3
l/d=4, 5
l/d=6
l/d=2, 3
l/d=4, 5
l/d=6
180HB
200
(180235)
0.07
0.06
0.05
(0.040.08) (0.040.07) (0.040.06)
0.08
0.07
0.06
(0.060.10) (0.060.08) (0.060.07)

180 280HB
140
(115180)
0.12
(0.080.18)
0.10
(0.080.12)
0.09
(0.080.10)
0.14
(0.080.24)
0.12
(0.080.16)
0.11
(0.100.12)

(AISI 4340etc.)
280 350HB
100
(75140)
0.12
(0.080.18)
0.10
(0.080.12)
0.09
(0.080.10)
0.14
(0.080.24)
0.12
(0.080.16)
0.11
(0.100.12)
Alloy Tool Steel

(SKD, SKTetc.)
350HB
135
(100170)
0.12
(0.080.18)
0.10
(0.080.12)
0.09
(0.080.10)
0.14
(0.080.24)
0.12
(0.080.16)
0.10
(0.080.12)

200HB
130
(80180)
0.10
(0.060.14)
0.08
0.07
(0.060.10) (0.060.08)
0.10
(0.060.14)
0.09
(0.060.12)
0.07
(0.060.10)

>200HB
130
(80180)
0.10
(0.060.14)
0.08
0.07
(0.060.10) (0.060.08)
0.10
(0.060.14)
0.09
(0.060.12)
0.07
(0.060.10)

Stainless Steel
200HB
120
(80165)
0.10
(0.060.14)
0.08
0.07
(0.060.10) (0.060.08)
0.10
(0.060.14)
0.09
(0.060.12)
0.07
(0.060.10)

Stainless Steel
>200HB
120
(80165)
0.10
(0.060.14)
0.08
0.07
(0.060.10) (0.060.08)
0.10
(0.060.14)
0.09
(0.060.12)
0.07
(0.060.10)
Gray Cast Iron

(FC300etc.)
Tensile Strength
160
(130195)
0.15
(0.100.20)
0.11
(0.100.13)
0.09
(0.080.10)
0.15
(0.100.20)
0.12
(0.100.13)
0.11
(0.100.12)
Ductile Cast Iron

(FCD450etc.)
Tensile Strength
100
(80135)
0.14
(0.100.18)
0.11
(0.100.12)
0.09
(0.080.10)
0.15
(0.100.20)
0.12
(0.100.13)
0.11
(0.100.12)
Ductile Cast Iron

(FCD700etc.)
Tensile Strength
100
(70125)
0.14
(0.100.18)
0.11
(0.100.12)
0.09
(0.080.10)
0.15
(0.100.20)
0.12
(0.100.13)
0.11
(0.100.12)
Note 1)
Note 2)
Note 3)
350MPa
450MPa
800MPa
Reduce the cutting speed by 30% when VP15TF is used as an outer insert.
Work material
&30&33
Feed per Tooth
(mm/rev)
Mild Steel
&24&29.5
Feed per Tooth
(mm/rev)
Hardness
Cutting Speed
Centre value
(Min.Max.)
(m/min)
&33.5&63
Feed per Tooth
(mm/rev)
l/d=26
l/d=2, 3
l/d=4, 5
l/d=6
Mild Steel
180HB
200
(180235)
0.08
(0.060.10)
0.07
(0.060.08)
0.06
(0.060.07)
Carbon Steel,Alloy Steel

180 280HB
140
(115180)
0.14
(0.080.24)
0.12
(0.080.16)
0.11
(0.100.12)
Carbon Steel,Alloy Steel

(AISI 4340etc.)
280 350HB
100
(75140)
0.14
(0.080.24)
0.12
(0.080.16)
0.11
(0.100.12)
Alloy Tool Steel

(SKD, SKTetc.)
350HB
135
(100170)
0.14
(0.080.24)
0.12
(0.080.16)
0.10
(0.080.12)

200HB
130
(80180)
0.09
(0.060.12)
0.08
(0.060.10)
0.07
(0.060.08)

>200HB
130
(80180)
0.09
(0.060.12)
0.08
(0.060.10)
0.07
(0.060.08)

Stainless Steel
200HB
120
(80165)
0.09
(0.060.12)
0.08
(0.060.10)
0.07
(0.060.08)

Stainless Steel
>200HB
120
(80165)
0.09
(0.060.12)
0.08
(0.060.10)
0.07
(0.060.08)
Gray Cast Iron

(FC300etc.)
Tensile Strength
160
(130195)
0.15
(0.100.20)
0.12
(0.100.13)
0.11
(0.100.12)
Ductile Cast Iron

(FCD450etc.)
Tensile Strength
100
(80135)
0.15
(0.100.20)
0.12
(0.100.13)
0.11
(0.100.12)
Ductile Cast Iron

(FCD700etc.)
Tensile Strength
100
(70125)
0.15
(0.100.20)
0.12
(0.100.13)
0.11
(0.100.12)
Note 1)
Note 2)
350MPa
450MPa
800MPa
DRILLING
CARBIDE
N219
CARBIDE
STAW
Small Diameter Indexable Drill
P
Steel

aHighly rigid clamping system offers stability and reliability for small hole drilling.
DCON
LF
140
DC
PL
LU
LH
OAL
STAWSS1000S16
23.8 33.8 81.8
STAWSN1000S16
STAWMN1000S16
STAWLN1000S16
LH OAL LF
38.8 48.8 96.8
80
PL DCON
1.8
16
10.4
(mm)
TIP06F
10.0
95
1.8
16
TIP06F
58.8 68.8 116.8 115
1.8
16
TIP06F
88.8 98.8 146.8 145
1.8
16
TIP06F
STAWSS1050S16
STAWSN1050S16
STAWMN1050S16
STAWLN1050S16
23.9 33.9 81.9

38.9 48.9 96.9
80
1.9
16
TIP06F
95
1.9
16
TIP06F
58.9 68.9 116.9 115
1.9
16
TIP06F
1.5
88.9 98.9 146.9 145
1.9
16
TIP06F
STAWSS1100S16
STAWSN1100S16
STAWMN1100S16
STAWLN1100S16
27.0 38.0 86.0
84
2.0
16
TIP06F
43.0 54.0 102.0 100
2.0
16
TIP06F
68.0 79.0 127.0 125
2.0
16
TIP06F
11.4
1.5
98.0 109.0 157.0 155
2.0
16
TIP06F
STAWSS1150S16
STAWSN1150S16
STAWMN1150S16
STAWLN1150S16
27.1 38.1 86.1
84
2.1
16
TIP06F
43.1 54.1 102.1 100
2.1
16
TIP06F
68.1 79.1 127.1 125
2.1
16
TIP06F
DRILLING
11.9
1.5
STAWSS1200S16
STAWSN1200S16
STAWMN1200S16
STAWLN1200S16
98.1 109.1 157.1 155

29.2 41.2 89.2
87
2.1
2.2
16
16
TIP06F
TIP06F
47.2 59.2 107.2 105
2.2
16
TIP06F
72.2 84.2 132.2 130
2.2
16
TIP06F
12.4
10.1
10.3
10.4
10.5
10.6
10.8
10.9
11.0
11.1
11.3
11.4
11.5
11.6
107.2 119.2 167.2 165
2.2
16
TIP06F
11.8
11.9
12.0
12.1
12.2
12.0
11.7
11.5
STAWN1010TH
STAWK1010TG
STAWN1020TH
STAWK1020TG
STAWN1030TH
STAWK1030TG
STAWN1040TH
STAWK1040TG
STAWN1050TH
STAWK1050TG
STAWN1060TH
STAWK1060TG
STAWN1070TH
STAWK1070TG
STAWN1080TH
STAWK1080TG
STAWN1090TH
STAWK1090TG
STAWN1100TH
STAWK1100TG
STAWN1110TH
STAWK1110TG
STAWN1120TH
STAWK1120TG
STAWN1130TH
STAWK1130TG
STAWN1140TH
STAWK1140TG
STAWN1150TH
STAWK1150TG
STAWN1160TH
STAWK1160TG
STAWN1170TH
STAWK1170TG
STAWN1180TH
STAWK1180TG
STAWN1190TH
STAWK1190TG
STAWN1200TH
STAWK1200TG
STAWN1210TH
STAWK1210TG
STAWN1220TH
STAWK1220TG
STAWN1230TH
STAWK1230TG
STAWN1240TH
STAWK1240TG
11.2
11.0
10.7
10.9
Order Number
10.2
1.5
10.5
STAWN1000TH
* STAWK1000TG
DC
Wrench
12.3
12.4
(Note 1) The above dimensions are for when installing the STAWN (VP15TF) insert.
N220
DP5010
LU
VP10H
Order Number
10.0
Insert
Stock
(l/d)
1.5
Dimensions (mm)
VP15TF
(mm)
Holder
Stock
DC
Hole Depth
y HOLDERS
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
29.3 41.3 89.3
STAWSN1250S16
STAWMN1250S16
STAWLN1250S16
LH OAL LF
87
PL DCON
2.3
16
(mm)
zTIP06F
12.5
47.3 59.3 107.3 105
2.3
16
zTIP06F
72.3 84.3 132.3 130
2.3
16
zTIP06F
107.3 119.3 167.3 165
2.3
16
zTIP06F
STAWSS1300S16
STAWSN1300S16
STAWMN1300S16
STAWLN1300S16
32.4 45.4 93.4
91
2.4
16
xTIP08W
51.4 64.4 112.4 110
2.4
16
xTIP08W
76.4 89.4 137.4 135
2.4
16
xTIP08W
1.5
116.4 129.4 177.4 175
2.4
16
xTIP08W
STAWSS1350S16
STAWSN1350S16
STAWMN1350S16
STAWLN1350S16
32.5 45.5 93.5
91
2.5
16
xTIP08W
51.5 64.5 112.5 110
2.5
16
xTIP08W
76.5 89.5 137.5 135
2.5
16
xTIP08W
13.9
1.5
116.5 129.5 177.5 175
2.5
16
xTIP08W
STAWSS1400S16
STAWSN1400S16
STAWMN1400S16
STAWLN1400S16
33.5 47.5 95.5
93
2.5
16
xTIP08W
55.5 69.5 117.5 115
2.5
16
xTIP08W
85.5 99.5 147.5 145
2.5
16
xTIP08W
14.4
1.5
STAWSS1450S16
STAWSN1450S16
STAWMN1450S16
STAWLN1450S16
124.5 139.5 187.5 185

33.6 47.6 95.6
93
2.5
2.6
16
16
xTIP08W
xTIP08W
55.6 69.6 117.6 115
2.6
16
xTIP08W
85.6 99.6 147.6 145
2.6
16
xTIP08W
14.9
1.5
124.6 139.6 187.6 185
2.6
16
xTIP08W
STAWSS1500S20
STAWSN1500S20
STAWMN1500S20
STAWLN1500S20
35.7 50.7 100.7
98
2.7
20
xTIP08W
62.7 77.7 127.7 125
2.7
20
xTIP08W
92.7 107.7 157.7 155
2.7
20
xTIP08W
15.4
12.6
12.8
12.9
13.0
13.1
13.3
13.4
13.5
13.6
13.8
13.9
14.0
14.1
14.3
14.4
14.5
14.6
132.7 150.7 200.7 198
2.7
20
xTIP08W
14.8
14.9
15.0
15.1
15.2
15.0
14.7
14.5
14.2
14.0
STAWN1260TH
STAWK1260TG
STAWN1270TH
STAWK1270TG
STAWN1280TH
STAWK1280TG
STAWN1290TH
STAWK1290TG
STAWN1300TH
STAWK1300TG
STAWN1310TH
STAWK1310TG
STAWN1320TH
STAWK1320TG
STAWN1330TH
STAWK1330TG
STAWN1340TH
STAWK1340TG
STAWN1350TH
STAWK1350TG
STAWN1360TH
STAWK1360TG
STAWN1370TH
STAWK1370TG
STAWN1380TH
STAWK1380TG
STAWN1390TH
STAWK1390TG
STAWN1400TH
STAWK1400TG
STAWN1410TH
STAWK1410TG
STAWN1420TH
STAWK1420TG
STAWN1430TH
STAWK1430TG
STAWN1440TH
STAWK1440TG
STAWN1450TH
STAWK1450TG
STAWN1460TH
STAWK1460TG
STAWN1470TH
STAWK1470TG
STAWN1480TH
STAWK1480TG
STAWN1490TH
STAWK1490TG
STAWN1500TH
STAWK1500TG
STAWN1510TH
STAWK1510TG
STAWN1520TH
STAWK1520TG
STAWN1530TH
STAWK1530TG
STAWN1540TH
STAWK1540TG
13.7
13.5
13.2
13.4
Order Number
12.7
1.5
13.0
STAWN1250TH
* STAWK1250TG
DC
Wrench
15.3
15.4
INSERT DESCRIPTION
CUTTING CONDITIONS
USAGE NOTE
TECHNICAL DATA
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
DRILLING
STAWSS1250S16
LU
DP5010
Order Number
VP10H
12.9
Insert
12.5
Stock
(l/d)
1.5
Dimensions (mm)
VP15TF
(mm)
Holder
Stock
DC
Hole Depth
CARBIDE
a
a
a
a
a
a
a
N223
N227
N228
Q001
N221
STAW
Dimensions (mm)
Insert
LH OAL LF
PL DCON
DC
Wrench
(mm)
15.5
1.5
STAWSS1600S20
36.8 52.8 102.8 100
2.8
20
TIP10W
Order Number
* STAWN1550T
STAWK1550TG
STAWN1560T
STAWK1560TG
STAWN1570T
STAWK1570TG
STAWN1580T
STAWK1580TG
STAWN1590T
STAWK1590TG
STAWN1600T
STAWK1600TG
STAWN1610T
STAWK1610TG
STAWN1620T
STAWK1620TG
STAWN1630T
STAWK1630TG
STAWN1640T
STAWK1640TG
STAWN1650T
STAWK1650TG
STAWN1660T
STAWK1660TG
STAWN1670T
STAWK1670TG
STAWN1680T
STAWK1680TG
STAWN1690T
STAWK1690TG
STAWN1700T
STAWK1700TG
STAWN1710T
STAWK1710TG
STAWN1720T
STAWK1720TG
STAWN1730T
STAWK1730TG
STAWN1740T
STAWK1740TG
STAWN1750T
STAWK1750TG
STAWN1760T
STAWK1760TG
STAWN1770T
STAWK1770TG
STAWN1780T
STAWK1780TG
STAWN1790T
STAWK1790TG
STAWN1800T
STAWK1800TG
STAWN1810T
STAWK1810TG
STAWN1820T
STAWK1820TG
STAWN1830T
STAWK1830TG
STAWN1840T
STAWK1840TG
15.6
15.7
STAWSN1600S20
62.8 82.8 132.8 130
2.8
20
TIP10W
15.8
15.9
15.5
16.4
16.0
5
STAWMN1600S20
92.8 117.8 167.8 165
2.8
20
TIP10W
16.1
16.2
STAWLN1600S20
140.8 160.8 210.8 208
2.8
20
TIP10W
16.3
16.4
16.5
1.5
STAWSS1700S20
39.0 56.0 106.0 103
3.0
20
TIP10W
16.6
16.7
STAWSN1700S20
64.0 88.0 138.0 135
3.0
20
TIP10W
16.8
16.9
16.5
17.4
17.0
5
STAWMN1700S20
98.0 123.0 173.0 170
3.0
20
TIP10W
17.1
17.2
STAWLN1700S20
149.0 169.0 219.0 216
3.0
20
TIP10W
17.3
17.4
17.5
1.5
STAWSS1800S20
40.2 58.2 108.2 105
3.2
20
TIP10W
17.6
17.7
STAWSN1800S20
67.2 93.2 143.2 140
3.2
20
TIP10W
17.8
17.9
17.5
DRILLING
18.4
18.0
5
STAWMN1800S20
103.2 128.2 178.2 175
3.2
20
TIP10W
18.1
18.2
STAWLN1800S20
157.2 177.2 227.2 224
3.2
20
TIP10W
18.3
18.4
(Note 1) The above dimensions are for when installing the STAWN (VP15TF) insert.

N222
DP5010
(l/d)
LU
VP10H
Stock
Order Number
VP15TF
(mm)
Holder
Stock
DC
Hole Depth
CARBIDE
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
CARBIDE
140
DC(h8)
INSERTS
VP10H
STAWN1000TH
STAWN1010TH
STAWN1020TH
STAWN1030TH
STAWN1040TH
STAWN1050TH
STAWN1060TH
STAWN1070TH
STAWN1080TH
STAWN1090TH
STAWN1100TH
STAWN1110TH
STAWN1120TH
STAWN1130TH
STAWN1140TH
STAWN1150TH
STAWN1160TH
STAWN1170TH
STAWN1180TH
STAWN1190TH
STAWN1200TH
STAWN1210TH
STAWN1220TH
STAWN1230TH
STAWN1240TH
STAWN1250TH
STAWN1260TH
STAWN1270TH
STAWN1280TH
STAWN1290TH
STAWN1300TH
STAWN1310TH
STAWN1320TH
STAWN1330TH
STAWN1340TH
STAWN1350TH
STAWN1360TH
STAWN1370TH
STAWN1380TH
STAWN1390TH
Dimensions (mm)
DC
LF
10.0
10.1
3.8
3.8
4.6
4.6
10.2
3.8
4.6
10.3
10.4
3.8
3.8
4.6
4.6
10.5
10.6
4.0
4.0
4.8
4.8
10.7
4.0
4.8
10.8
10.9
4.0
4.0
4.8
4.8
11.0
11.1
4.2
4.2
5.1
5.1
11.2
4.2
5.1
11.3
11.4
4.2
4.2
5.1
5.1
11.5
11.6
4.4
4.4
5.3
5.3
11.7
4.4
5.3
11.8
11.9
4.4
4.4
5.3
5.3
12.0
12.1
4.6
4.6
5.5
5.5
12.2
4.6
5.5
12.3
12.4
4.6
4.6
5.5
5.5
12.5
12.6
4.8
4.8
5.8
5.8
12.7
4.8
5.8
12.8
12.9
4.8
4.8
5.8
5.8
13.0
13.1
4.9
4.9
6.0
6.0
13.2
4.9
6.0
13.3
13.4
4.9
4.9
6.0
6.0
13.5
13.6
5.1
5.1
6.2
6.2
13.7
5.1
6.2
13.8
13.9
5.1
5.1
6.2
6.2
Applicable Holder
STAWSS1000S16
STAWSN1000S16
STAWMN1000S16
STAWLN1000S16
STAWSS1050S16
STAWSN1050S16
STAWMN1050S16
STAWLN1050S16
STAWSS1100S16
STAWSN1100S16
STAWMN1100S16
STAWLN1100S16
STAWSS1150S16
STAWSN1150S16
STAWMN1150S16
STAWLN1150S16
STAWSS1200S16
STAWSN1200S16
STAWMN1200S16
STAWLN1200S16
STAWSS1250S16
STAWSN1250S16
STAWMN1250S16
STAWLN1250S16
STAWSS1300S16
STAWSN1300S16
DRILLING
VP15TF
Stock
Order Number
LF
STAWMN1300S16
STAWLN1300S16
STAWSS1350S16
STAWSN1350S16
STAWMN1350S16
STAWLN1350S16
CUTTING CONDITIONS
USAGE NOTE
TECHNICAL DATA
N227
N228
Q001
N223
CARBIDE
STAW
N224
STAWN1400TH
STAWN1410TH
STAWN1420TH
STAWN1430TH
STAWN1440TH
STAWN1450TH
STAWN1460TH
STAWN1470TH
STAWN1480TH
STAWN1490TH
STAWN1500TH
STAWN1510TH
STAWN1520TH
STAWN1530TH
STAWN1540TH
STAWN1550T
STAWN1560T
STAWN1570T
STAWN1580T
STAWN1590T
STAWN1600T
STAWN1610T
STAWN1620T
STAWN1630T
STAWN1640T
STAWN1650T
STAWN1660T
STAWN1670T
STAWN1680T
STAWN1690T
STAWN1700T
STAWN1710T
STAWN1720T
STAWN1730T
STAWN1740T
STAWN1750T
STAWN1760T
STAWN1770T
STAWN1780T
STAWN1790T
STAWN1800T
STAWN1810T
STAWN1820T
STAWN1830T
STAWN1840T
VP10H
VP15TF
DRILLING
Stock
Order Number
Dimensions (mm)
Applicable Holder
DC
LF
14.0
5.3
6.4
14.1
5.3
6.4
14.2
5.3
6.4
14.3
14.4
5.3
5.3
6.4
6.4
14.5
14.6
5.5
5.5
6.7
6.7
14.7
5.5
6.7
14.8
14.9
5.5
5.5
6.7
6.7
15.0
15.1
5.7
5.7
6.9
6.9
15.2
5.7
6.9
15.3
15.4
5.7
5.7
6.9
6.9
15.5
15.6
5.9
5.9
7.1
7.1
15.7
5.9
7.1
15.8
15.9
5.9
5.9
7.1
7.1
STAWSS1600S20
5.9
5.9
7.1
7.1
STAWMN1600S20
16.0
16.1
16.2
5.9
7.1
16.3
16.4
5.9
5.9
7.1
7.1
16.5
16.6
6.3
6.3
7.6
7.6
16.7
6.3
7.6
16.8
16.9
6.3
6.3
7.6
7.6
STAWSS1700S20
6.3
6.3
7.6
7.6
STAWMN1700S20
17.0
17.1
17.2
6.3
7.6
17.3
17.4
6.3
6.3
7.6
7.6
17.5
17.6
6.7
6.7
8.1
8.1
17.7
6.7
8.1
17.8
17.9
6.7
6.7
8.1
8.1
STAWSS1800S20
18.0
18.1
6.7
6.7
8.1
8.1
STAWMN1800S20
a
a
18.2
6.7
8.1
18.3
18.4
6.7
6.7
8.1
8.1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a

STAWSS1400S16
STAWSN1400S16
STAWMN1400S16
STAWLN1400S16
STAWSS1450S16
STAWSN1450S16
STAWMN1450S16
STAWLN1450S16
STAWSS1500S20
STAWSN1500S20
STAWMN1500S20
STAWLN1500S20
STAWSN1600S20
STAWLN1600S20
STAWSN1700S20
STAWLN1700S20
STAWSN1800S20
STAWLN1800S20
CARBIDE
DC(h8)
(Cast Iron)
STAWK1000TG
STAWK1010TG
STAWK1020TG
STAWK1030TG
STAWK1040TG
STAWK1050TG
STAWK1060TG
STAWK1070TG
STAWK1080TG
STAWK1090TG
STAWK1100TG
STAWK1110TG
STAWK1120TG
STAWK1130TG
STAWK1140TG
STAWK1150TG
STAWK1160TG
STAWK1170TG
STAWK1180TG
STAWK1190TG
STAWK1200TG
STAWK1210TG
STAWK1220TG
STAWK1230TG
STAWK1240TG
STAWK1250TG
STAWK1260TG
STAWK1270TG
STAWK1280TG
STAWK1290TG
STAWK1300TG
STAWK1310TG
STAWK1320TG
STAWK1330TG
STAWK1340TG
STAWK1350TG
STAWK1360TG
STAWK1370TG
STAWK1380TG
STAWK1390TG
Dimensions (mm)
DC
LF
10.0
10.1
3.3
3.3
4.6
4.6
10.2
3.3
4.6
10.3
10.4
3.3
3.3
4.6
4.6
10.5
10.6
3.5
3.5
4.8
4.8
10.7
3.5
4.8
10.8
10.9
3.5
3.5
4.8
4.8
11.0
11.1
3.7
3.7
5.1
5.1
11.2
3.7
5.1
11.3
11.4
3.7
3.7
5.1
5.1
11.5
11.6
3.9
3.9
5.3
5.3
11.7
3.9
5.3
11.8
11.9
3.9
3.9
5.3
5.3
12.0
12.1
4.1
4.1
5.5
5.5
12.2
4.1
5.5
12.3
12.4
4.1
4.1
5.5
5.5
12.5
12.6
4.2
4.2
5.8
5.8
12.7
4.2
5.8
12.8
12.9
4.2
4.2
5.8
5.8
13.0
13.1
4.4
4.4
6.0
6.0
13.2
4.4
6.0
13.3
13.4
4.4
4.4
6.0
6.0
13.5
13.6
4.6
4.6
6.2
6.2
13.7
4.6
6.2
13.8
13.9
4.6
4.6
6.2
6.2
a
a
a
a
a
a
a
a
a
a
a
a
a
a
LF
Applicable Holder
STAWSS1000S16
STAWSN1000S16
STAWMN1000S16
STAWLN1000S16
STAWSS1050S16
STAWSN1050S16
STAWMN1050S16
STAWLN1050S16
STAWSS1100S16
STAWSN1100S16
STAWMN1100S16
STAWLN1100S16
STAWSS1150S16
STAWSN1150S16
STAWMN1150S16
STAWLN1150S16
STAWSS1200S16
STAWSN1200S16
STAWMN1200S16
STAWLN1200S16
STAWSS1250S16
STAWSN1250S16
STAWMN1250S16
STAWLN1250S16
STAWSS1300S16
STAWSN1300S16
STAWMN1300S16
STAWLN1300S16
DRILLING
DP5010
Stock
Order Number
140
INSERTS
STAWSS1350S16
STAWSN1350S16
STAWMN1350S16
STAWLN1350S16
N225
CARBIDE
STAW
STAWK1400TG
STAWK1410TG
STAWK1420TG
STAWK1430TG
STAWK1440TG
STAWK1450TG
STAWK1460TG
STAWK1470TG
STAWK1480TG
STAWK1490TG
STAWK1500TG
STAWK1510TG
STAWK1520TG
STAWK1530TG
STAWK1540TG
STAWK1550TG
STAWK1560TG
STAWK1570TG
STAWK1580TG
STAWK1590TG
STAWK1600TG
STAWK1610TG
STAWK1620TG
STAWK1630TG
STAWK1640TG
STAWK1650TG
STAWK1660TG
STAWK1670TG
STAWK1680TG
STAWK1690TG
STAWK1700TG
STAWK1710TG
STAWK1720TG
STAWK1730TG
STAWK1740TG
STAWK1750TG
STAWK1760TG
STAWK1770TG
STAWK1780TG
STAWK1790TG
STAWK1800TG
STAWK1810TG
STAWK1820TG
STAWK1830TG
STAWK1840TG
DC
LF
14.0
4.8
6.4
14.1
4.8
6.4
14.2
4.8
6.4
14.3
14.4
4.8
4.8
6.4
6.4
14.5
14.6
5.0
5.0
6.7
6.7
14.7
5.0
6.7
14.8
14.9
5.0
5.0
6.7
6.7
15.0
15.1
5.2
5.2
6.9
6.9
15.2
5.2
6.9
15.3
15.4
5.2
5.2
6.9
6.9
15.5
15.6
5.3
5.3
7.1
7.1
15.7
5.3
7.1
15.8
5.3
7.1
STAWSS1600S20
15.9
5.3
7.1
STAWSN1600S20
16.0
5.3
7.1
STAWMN1600S20
16.1
5.3
7.1
STAWLN1600S20
16.2
5.3
7.1
16.3
16.4
5.3
5.3
7.1
7.1
16.5
16.6
5.7
5.7
7.6
7.6
16.7
5.7
7.6
16.8
5.7
7.6
STAWSS1700S20
16.9
5.7
7.6
STAWSN1700S20
17.0
5.7
7.6
STAWMN1700S20
17.1
5.7
7.6
STAWLN1700S20
17.2
5.7
7.6
17.3
17.4
5.7
5.7
7.6
7.6
17.5
17.6
6.0
6.0
8.1
8.1
17.7
6.0
8.1
17.8
6.0
8.1
STAWSS1800S20
17.9
6.0
8.1
STAWSN1800S20
18.0
6.0
8.1
STAWMN1800S20
18.1
6.0
8.1
STAWLN1800S20
18.2
6.0
8.1
18.3
18.4
6.0
6.0
8.1
8.1
a
a
a
a
a
a
a
a
a
a

a
N226
Order Number
Dimensions (mm)
DP5010
DRILLING
Stock
Applicable Holder
STAWSS1400S16
STAWSN1400S16
STAWMN1400S16
STAWLN1400S16
STAWSS1450S16
STAWSN1450S16
STAWMN1450S16
STAWLN1450S16
STAWSS1500S20
STAWSN1500S20
STAWMN1500S20
STAWLN1500S20
CARBIDE
y HONE WIDTH
If an insert with honing other than standard is needed, please order
using the symbols below.
(Honing Standard)
(Insert Order Number)
Honing Symbol
STAW
Product Name
N : General Use Insert Diameter
K : For Cast Iron
Honing Type
Honing Type
F
G
H
K
S
M
Hone Width (mm)
0
0.02 0.05
0.05 0.10
0.10 0.15
0.15 0.20
0.20 0.25
0.25 0.30

Drill Diameter
Work Material
& 13.0 & 13.9
& 14.0 & 15.4
& 15.5 & 18.4
Feed
(mm/rev)
Cutting Speed
(m/min)
Feed
(mm/rev)
Cutting Speed
(m/min)
Feed
(mm/rev)
Cutting Speed
(m/min)
Feed
(mm/rev)
< 180HB
80
(60 100)
0.20
(0.15 0.25)
90
(70 110)
0.25
(0.20 0.30)
100
(80 120)
0.30
(0.25 0.35)
100
(80 120)
0.35
(0.25 0.40)
180 280HB
80
(60 100)
0.20
(0.15 0.25)
90
(70 110)
0.25
(0.20 0.30)
100
(80 120)
0.30
(0.25 0.35)
100
(80 120)
0.35
(0.25 0.40)
280 350HB
70
(60 90)
0.20
(0.15 0.25)
80
(60 100)
0.25
(0.20 0.30)
90
(70 110)
0.25
(0.20 0.30)
90
(70 110)
0.30
(0.20 0.35)
< 200HB
40
(30 50)
0.13
(0.10 0.16)
50
(40 60)
0.15
(0.12 0.18)
60
(50 70)
0.17
(0.14 0.20)
60
(50 70)
0.17
(0.14 0.20)
Tensile Strength
80
(60 100)
0.20
(0.15 0.25)
90
(70 110)
0.25
(0.20 0.30)
100
(80 120)
0.30
(0.25 0.35)
120
(80 140)
0.45
(0.35 0.55)
Strength
Ductile Cast Iron Tensile
< 450MPa
70
(60 90)
0.20
(0.15 0.25)
80
(60 100)
0.25
(0.20 0.30)
90
(70 110)
0.30
(0.25 0.35)
100
(80 120)
0.35
(0.25 0.40)
Mild Steel
Carbon Steel
Alloy Steel
& 10.0 & 12.9
Conditions Cutting Speed

(m/min)
Hardness
Stainless Steel
Gray Cast Iron
< 350MPa
DRILLING
(Note 1) When using a drill for 1.5DC depth of hole, it is possible to increase the feed rate by approx. 20%.
(Note 2) When using the 8DC type holder, reduce the cutting speed by approx. 20%.
(Note 3) When using the 8DC type holder, it is recommended to drill a pilot guide hole.
(Note 4) For stainless steel, please use internal coolant. (Mist & MQL are not recommended).
N227
CARBIDE
STAW
NOTES ON USE
Stopper
y INSERT INSTALLATION
1. Before inserting the insert into the holder, ensure that there are no foreign objects
or dirt in the holder slot or slit. If there are any foreign objects or dirt,
use compressed air to remove them.
Internal
screw
Holder slot
Slit
2. Use the provided wrench to loosen the inner screw to open the tip of the holder,
then put the insert into the holder slot as shown in figure 1.
*Ensure that the wrench is firmly in contact with the base of the inner screw head
when tightening.
3. After the insert has been set in the holder slot, tighten the inner screw while
holding the insert lightly as shown in figure 2 to securely clamp and locate the
insert.
*Ensure that the wrench is firmly in contact with the base of the inner screw head
when tightening.
Fig. 1

Drill Diameter (mm)
Clamp Torque
Nm
10
12.9
13
15.4
15.5 18.4
2.5
Fig. 2
4. Check there is no gap between the bottom of the insert and holder slot.
OK
Alignment mark
No clearance
NG
Clearance
(Note) Poor or incorrect clamping of inserts can cause poor drilling performance and/or drill breakage.
Therefore ensure that the alignment marks on both the body and insert are aligned when setting.
When machining, use safety guards and goggles.
SPARE PARTS
DRILLING
Applicable Holder
STAWSS/SN/MN/LN1000S16
Pack Order Number

(Internal screw & stopper)
Internal screw
Stopper
WS203107TPS-35LH
WS203107TPS
WS35LH
WS203107TPS-35LH
WS203107TPS
WS35LH
WS203108TPS-35LH
WS203108TPS
WS35LH
WS203108TPS-35LH
WS203108TPS
WS35LH
WS203108TPS-35LH
WS203108TPS
WS35LH
WS203108TPS-35LH
WS203108TPS
WS35LH
WS253909TPS-45LH
WS253909TPS
WS45LH
WS253909TPS-45LH
WS253909TPS
WS45LH
WS253909TPS-45LH
WS253909TPS
WS45LH
WS253909TPS-45LH
WS253909TPS
WS45LH
WS253909TPS-45LH
WS253909TPS
WS45LH
WS304912TPS-55LH
WS304912TPS
WS55LH
WS304912TPS-55LH
WS304912TPS-55LH
WS304912TPS
WS304912TPS
WS55LH
WS55LH
(Note) The parts are packaged internal screw, stopper and operation manual. Please replace the parts in accordance with the operation
manual.
N228
TAW
P
CARBIDE
(General Use)
LF
140
DC
PL
DCON
Steel

aSerration geometry for accurate insert location.
LU
LH
OAL
Insert
LU
LH OAL LF
PL DCON
Clamp
Screw
Wrench
Plate
DC
Anti-seize
(mm)
Lubricant
18.5
3
TAWSN1900S25
71.4 102.4 158.4 155
3.4
18.6
18.7
18.8
18.9
18.5
19.4
TAWMN1900S25
110.4 137.4 193.4 190
3.4
19.0
19.1
19.2
TAWLN1900S25
165.5 188.5 244.5 241
3.5
25 WS304517T TKY10T WPT4405 MK1KS 19.3

19.4
19.5
TAWSN2000S25
75.5 102.5 158.5 155
3.5
19.6
19.7
19.8
19.9
19.5
20.4
TAWMN2000S25
116.6 142.6 198.6 195
3.6
20.0
20.1
20.2
TAWLN2000S25
173.7 196.7 252.7 249
3.7
25 WS304518T TKY10T WPT4405 MK1KS 20.3

20.4
TAWNH1850T
TAWKH1850TG
TAWNH1860T
TAWKH1860TG
TAWNH1870T
TAWKH1870TG
TAWNH1880T
TAWKH1880TG
TAWNH1890T
TAWKH1890TG
TAWNH1900T
TAWKH1900TG
TAWNH1910T
TAWKH1910TG
TAWNH1920T
TAWKH1920TG
TAWNH1930T
TAWKH1930TG
TAWNH1940T
TAWKH1940TG
TAWNH1950T
TAWKH1950TG
TAWNH1960T
TAWKH1960TG
TAWNH1970T
TAWKH1970TG
TAWNH1980T
TAWKH1980TG
TAWNH1990T
TAWKH1990TG
TAWNH2000T
TAWKH2000TG
TAWNH2010T
TAWKH2010TG
TAWNH2020T
TAWKH2020TG
TAWNH2030T
TAWKH2030TG
TAWNH2040T
TAWKH2040TG
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
a
r
r
r
r
r
r
DRILLING
Order Number
(l/d)
VP10H
Stock
Order
Number
DP5010
(mm)
Dimensions (mm)
VP15TF
DC
Holder
Stock
Hole Depth
y HOLDERS
(Note 1) The dimensions in brackets represent the sizes when TAWNH type inserts are used.
a
r

INSERT DESCRIPTION
CUTTING CONDITIONS
N234
N238
USAGE NOTE
TECHNICAL DATA
N238
Q001
N229
TAW
Insert
Order Number
(l/d)
LU
LH OAL LF
PL DCON
Clamp
Screw
Wrench
Plate
DC
Anti-seize
(mm)
Lubricant
20.5
3
TAWSN2100S25
78.7 102.7 158.7 155.0 3.7
* TAWNH2050T
TAWKH2050TG
TAWNH2060T
TAWKH2060TG
TAWNH2070T
TAWKH2070TG
TAWNH2080T
TAWKH2080TG
TAWNH2090T
TAWKH2090TG
TAWNH2100T
TAWKH2100TG
TAWNH2110T
TAWKH2110TG
TAWNH2120T
TAWKH2120TG
TAWNH2130T
TAWKH2130TG
TAWNH2140T
TAWKH2140TG
TAWNH2150T
TAWKH2150TG
TAWNH2160T
TAWKH2160TG
TAWNH2170T
TAWKH2170TG
TAWNH2180T
TAWKH2180TG
TAWNH2190T
TAWKH2190TG
TAWNH2200T
TAWKH2200TG
TAWNH2210T
TAWKH2210TG
TAWNH2220T
TAWKH2220TG
TAWNH2230T
TAWKH2230TG
TAWNH2240T
TAWKH2240TG
TAWNH2250T
TAWKH2250TG
TAWNH2260T
TAWKH2260TG
TAWNH2270T
TAWKH2270TG
TAWNH2280T
TAWKH2280TG
TAWNH2290T
TAWKH2290TG
TAWNH2300T
TAWKH2300TG
TAWNH2310T
TAWKH2310TG
TAWNH2320T
TAWKH2320TG
TAWNH2330T
TAWKH2330TG
TAWNH2340T
TAWKH2340TG
20.6
20.7
20.8
20.9
20.5
21.4
TAWMN2100S25
121.8 142.8 198.7 195.0 3.7
21.0
21.1
21.2
TAWLN2100S25
181.7 205.7 261.7 258.0 3.7
25 WS304518T TKY10T WPT4405 MK1KS 21.3

21.4
21.5
TAWSN2200S25
83.2 108.2 164.2 160.3 3.9
21.6
21.7
21.8
21.9
21.5
22.4
TAWMN2200S25
128.2 148.2 204.2 200.3 3.9
22.0
22.1
22.2
TAWLN2200S25
189.9 213.9 269.9 266.0 3.9
25 WS355520T TKY15T WPT4405 MK1KS 22.3

22.4
22.5
TAWSN2300S25
86.4 108.4 164.4 160.3 4.1
22.6
22.7
22.9
22.5
DRILLING
22.8
23.4
TAWMN2300S25
133.4 158.4 214.4 210.3 4.1
23.0
23.1
23.2
TAWLN2300S25
198.1 227.1 283.1 279.0 4.1
25 WS355521T TKY15T WPT4405 MK1KS 23.3

23.4
N230
VP10H
Stock
Order
Number
DP5010
(mm)
Dimensions (mm)
VP15TF
DC
Holder
Stock
Hole Depth
CARBIDE
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
Dimensions (mm)
Insert
LH OAL LF
PL DCON
Clamp
Screw
Wrench
Plate
DC
Anti-seize
(mm)
Lubricant
23.5
3
TAWSN2400S32
90.6 114.6 174.6 170.3 4.3
* TAWNH2350T
TAWKH2350TG
TAWNH2360T
TAWKH2360TG
TAWNH2370T
TAWKH2370TG
TAWNH2380T
TAWKH2380TG
TAWNH2390T
TAWKH2390TG
TAWNH2400T
TAWKH2400TG
TAWNH2410T
TAWKH2410TG
TAWNH2420T
TAWKH2420TG
TAWNH2430T
TAWKH2430TG
TAWNH2440T
TAWKH2440TG
TAWNH2450T
TAWKH2450TG
TAWNH2460T
TAWKH2460TG
TAWNH2470T
TAWKH2470TG
TAWNH2480T
TAWKH2480TG
TAWNH2490T
TAWKH2490TG
TAWNH2500T
TAWKH2500TG
TAWNH2510T
TAWKH2510TG
TAWNH2520T
TAWKH2520TG
TAWNH2530T
TAWKH2530TG
TAWNH2540T
TAWKH2540TG
TAWNH2550T
TAWKH2550TG
TAWNH2560T
TAWKH2560TG
TAWNH2570T
TAWKH2570TG
TAWNH2580T
TAWKH2580TG
TAWNH2590T
TAWKH2590TG
TAWNH2600T
TAWKH2600TG
TAWNH2610T
TAWKH2610TG
TAWNH2620T
TAWKH2620TG
TAWNH2630T
TAWKH2630TG
TAWNH2640T
TAWKH2640TG
23.6
23.7
23.8
23.9
23.5
24.4
TAWMN2400S32
139.6 164.6 224.6 220.3 4.3
24.0
24.1
24.2
TAWLN2400S32
206.3 236.3 296.3 292.0 4.3
32 WS355521T TKY15T WPT4405 MK1KS 24.3

24.4
24.5
TAWSN2500S32
93.1 115.1 175.1 170.6 4.5
24.6
24.7
24.8
24.9
24.5
25.4
TAWMN2500S32
145.1 170.1 230.1 225.6 4.5
25.0
25.1
25.2
TAWLN2500S32
214.5 244.5 304.5 300.0 4.5
32 WS406023T TKY25T WPT4405 MK1KS 25.3

25.4
25.5
TAWSN2600S32
97.2 120.2 180.2 175.6 4.6
25.6
25.7
25.8
25.9
25.5
26.4
TAWMN2600S32
151.2 175.2 235.2 230.6 4.6
26.0
26.1
26.2
TAWLN2600S32
222.6 252.6 312.6 308.0 4.6
32 WS406024T TKY25T WPT4405 MK1KS 26.3

26.4
INSERT DESCRIPTION
CUTTING CONDITIONS
USAGE NOTE
TECHNICAL DATA
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
DRILLING
LU
VP10H
Order Number
(l/d)
DP5010
Stock
Order
Number
VP15TF
(mm)
Holder
Stock
DC
Hole Depth
CARBIDE
a
r
r
r
r
r
r
r
r
r
N234
N238
N238
Q001
N231
TAW
Insert
Order Number
(l/d)
LU
LH OAL LF
PL DCON
Clamp
Screw
Wrench
Plate
DC
Anti-seize
(mm)
Lubricant
26.5
3
TAWSN2700S32
99.4 120.4 180.4 175.6 4.8
* TAWNH2650T
TAWKH2650TG
TAWNH2660T
TAWKH2660TG
TAWNH2670T
TAWKH2670TG
TAWNH2680T
TAWKH2680TG
TAWNH2690T
TAWKH2690TG
TAWNH2700T
TAWKH2700TG
TAWNH2710T
TAWKH2710TG
TAWNH2720T
TAWKH2720TG
TAWNH2730T
TAWKH2730TG
TAWNH2740T
TAWKH2740TG
TAWNH2750T
TAWKH2750TG
TAWNH2760T
TAWKH2760TG
TAWNH2770T
TAWKH2770TG
TAWNH2780T
TAWKH2780TG
TAWNH2790T
TAWKH2790TG
TAWNH2800T
TAWKH2800TG
TAWNH2810T
TAWKH2810TG
TAWNH2820T
TAWKH2820TG
TAWNH2830T
TAWKH2830TG
TAWNH2840T
TAWKH2840TG
TAWNH2850T
TAWKH2850TG
TAWNH2860T
TAWKH2860TG
TAWNH2870T
TAWKH2870TG
TAWNH2880T
TAWKH2880TG
TAWNH2890T
TAWKH2890TG
TAWNH2900T
TAWKH2900TG
TAWNH2910T
TAWKH2910TG
TAWNH2920T
TAWKH2920TG
TAWNH2930T
TAWKH2930TG
TAWNH2940T
TAWKH2940TG
26.6
26.7
26.8
26.9
26.5
27.4
TAWMN2700S32
156.4 180.4 240.4 235.6 4.8
27.0
27.1
27.2
TAWLN2700S32
230.8 260.8 320.8 316.0 4.8
32 WS406024T TKY25T WPT4405 MK1KS 27.3

27.4
27.5
TAWSN2800S32
102.2 125.2 185.2 180.2 5.0
27.6
27.7
27.8
27.9
27.5
28.4
TAWMN2800S32
162.2 185.2 245.2 240.2 5.0
28.0
28.1
28.2
TAWLN2800S32
239.0 269.0 329.0 324.0 5.0
32 WS508026T TKY27T WPT4405 MK1KS 28.3

28.4
28.5
TAWSN2900S32
105.4 130.4 190.4 185.2 5.2
28.6
28.7
28.9
28.5
DRILLING
28.8
29.4
TAWMN2900S32
167.4 190.4 250.4 245.2 5.2
29.0
29.1
29.2
TAWLN2900S32
247.2 277.2 337.2 332.0 5.2
32 WS508027T TKY27T WPT4405 MK1KS 29.3

29.4
N232
VP10H
Stock
Order
Number
DP5010
(mm)
Dimensions (mm)
VP15TF
DC
Holder
Stock
Hole Depth
CARBIDE
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
Dimensions (mm)
Insert
LU
LH OAL LF
PL DCON
Clamp
Screw
Wrench
Plate
DC
Anti-seize
(mm)
Lubricant
29.5
3
TAWSN3000S32
109.6 130.6 190.6 185.2 5.4
29.6
29.7
29.8
29.9
30.4
TAWMN3000S32
172.6 200.6 260.6 255.2 5.4
30.0
30.1
30.2
TAWLN3000S32
255.4 290.4 350.4 345.0 5.4
32 WS508027T TKY27T WPT4405 MK1KS 30.3

30.4
TAWNH2960T
TAWKH2960TG
TAWNH2970T
TAWKH2970TG
TAWNH2980T
TAWKH2980TG
TAWNH2990T
TAWKH2990TG
TAWNH3000T
TAWKH3000TG
TAWNH3010T
TAWKH3010TG
TAWNH3020T
TAWKH3020TG
TAWNH3030T
TAWKH3030TG
TAWNH3040T
TAWKH3040TG
r
a
r
r
r
r
r
r
r
r
r
a
r
r
r
r
r
r
r
r
DRILLING
29.5
* TAWNH2950T
TAWKH2950TG
VP10H
Order Number
(l/d)
DP5010
Stock
Order
Number
VP15TF
(mm)
Holder
Stock
DC
Hole Depth
CARBIDE
INSERT DESCRIPTION
CUTTING CONDITIONS
USAGE NOTE
TECHNICAL DATA
N234
N238
N238
Q001
N233
CARBIDE
TAW
H Type
140
DC(h7)
INSERTS
DC
LF
14.0
14.1
7.6
7.6
5.0
5.0
14.2
7.6
5.0
14.3
14.4
7.6
7.6
5.0
5.0
14.5
14.6
7.5
7.5
5.0
5.0
14.7
7.5
5.0
14.8
7.5
5.0
14.9
7.5
5.0
15.0
7.4
5.0
15.1
7.4
5.0
15.2
7.4
5.0
15.3
15.4
7.4
7.4
5.0
5.0
15.5
15.6
7.9
7.9
6.0
6.0
15.7
7.9
6.0
15.8
7.9
6.0
15.9
7.9
6.0
16.0
7.8
6.0
16.1
7.8
6.0
16.2
7.8
6.0
16.3
16.4
7.8
7.8
6.0
6.0
16.5
16.6
7.7
7.7
6.0
6.0
16.7
7.7
6.0
16.8
7.7
6.0
16.9
7.7
6.0
17.0
7.6
6.0
17.1
7.6
6.0
17.2
7.6
6.0
17.3
17.4
7.6
7.6
6.0
6.0
17.5
17.6
7.5
7.5
6.0
6.0
17.7
7.5
6.0
17.8
7.5
6.0
17.9
7.5
6.0
18.0
7.4
6.0
18.1
7.4
6.0
18.2
7.4
6.0
18.3
18.4
7.4
7.4
6.0
6.0
[
[
[
[
[
[
[
[
Applicable
Holder
TAWSNH
1400S16
TAWMNH
1400S16
TAWLNH
1400S16
TAWSNH
1500S20
TAWMNH
1500S20
TAWLNH
1500S20
TAWSN
1600S20
TAWMN
1600S20
TAWLN
1600S20
TAWSN
1700S20
TAWMN
1700S20
TAWLN
1700S20
TAWSN
1800S20
TAWMN
1800S20
TAWLN
1800S20
Stock
[:
Dimensions (mm)
Order Number
DC
TAWNH1850T
TAWNH1860T
TAWNH1870T
TAWNH1880T
TAWNH1890T
TAWNH1900T
TAWNH1910T
TAWNH1920T
TAWNH1930T
TAWNH1940T
TAWNH1950T
TAWNH1960T
TAWNH1970T
TAWNH1980T
TAWNH1990T
TAWNH2000T
TAWNH2010T
TAWNH2020T
TAWNH2030T
TAWNH2040T
TAWNH2050T
TAWNH2060T
TAWNH2070T
TAWNH2080T
TAWNH2090T
TAWNH2100T
TAWNH2110T
TAWNH2120T
TAWNH2130T
TAWNH2140T
TAWNH2150T
TAWNH2160T
TAWNH2170T
TAWNH2180T
TAWNH2190T
TAWNH2200T
TAWNH2210T
TAWNH2220T
TAWNH2230T
TAWNH2240T
TAWNH2250T
TAWNH2260T
TAWNH2270T
TAWNH2280T
TAWNH2290T
a r
18.5
9.3
7.0
a r
18.6
9.3
7.0
a r
18.7
9.3
7.0
a r
18.8
9.3
7.0
a r
18.9
9.3
7.0
a r
19.0
9.2
7.0
a r
19.1
9.2
7.0
a r
19.2
9.2
7.0
a r
19.3
19.4
9.2
9.2
7.0
7.0
a r
19.5
19.6
9.1
9.1
7.0
7.0
a r
19.7
9.1
7.0
a r
19.8
9.1
7.0
a r
19.9
9.1
7.0
a r
20.0
9.0
7.0
r r
20.1
9.0
7.0
r r
20.2
9.0
7.0
r r
20.3
20.4
9.0
9.0
7.0
7.0
r r
20.5
20.6
8.9
8.9
7.0
7.0
r r
20.7
8.9
7.0
r r
20.8
8.9
7.0
r r
20.9
8.9
7.0
a r
21.0
8.8
7.0
r r
21.1
8.8
7.0
r r
21.2
8.8
7.0
r r
21.3
21.4
8.8
8.8
7.0
7.0
r r
21.5
21.6
10.6
10.6
8.0
8.0
r r
21.7
10.6
8.0
r r
21.8
10.6
8.0
r r
21.9
10.6
8.0
a r
22.0
10.5
8.0
r r
22.1
10.5
8.0
r r
22.2
10.5
8.0
r r
22.3
22.4
10.5
10.5
8.0
8.0
r r
22.5
22.6
10.4
10.4
8.0
8.0
r r
22.7
10.4
8.0
r r
22.8
22.9
10.4
10.4
8.0
8.0

Inventory maintained in Japan. To be replaced by new products.
a
N234
Dimensions (mm)
VP15TF
VP10H
DRILLING
TAWNH1400T
TAWNH1410T
TAWNH1420T
TAWNH1430T
TAWNH1440T
TAWNH1450T
TAWNH1460T
TAWNH1470T
TAWNH1480T
TAWNH1490T
TAWNH1500T
TAWNH1510T
TAWNH1520T
TAWNH1530T
TAWNH1540T
TAWNH1550T
TAWNH1560T
TAWNH1570T
TAWNH1580T
TAWNH1590T
TAWNH1600T
TAWNH1610T
TAWNH1620T
TAWNH1630T
TAWNH1640T
TAWNH1650T
TAWNH1660T
TAWNH1670T
TAWNH1680T
TAWNH1690T
TAWNH1700T
TAWNH1710T
TAWNH1720T
TAWNH1730T
TAWNH1740T
TAWNH1750T
TAWNH1760T
TAWNH1770T
TAWNH1780T
TAWNH1790T
TAWNH1800T
TAWNH1810T
TAWNH1820T
TAWNH1830T
TAWNH1840T
VP15TF
VP10H
Stock
Order Number
LF
a r
a r
r r
a r
r r
a r
r r
a r
r r
LF
Applicable
Holder
TAWSN
1900S25
TAWMN
1900S25
TAWLN
1900S25
TAWSN
2000S25
TAWMN
2000S25
TAWLN
2000S25
TAWSN
2100S25
TAWMN
2100S25
TAWLN
2100S25
TAWSN
2200S25
TAWMN
2200S25
TAWLN
2200S25
TAWSN
2300S25
TAWMN
2300S25
TAWLN
2300S25
CARBIDE
a r
23.0
10.3
8.0
r r
23.1
10.3
8.0
r r
23.2
10.3
8.0
r r
23.3
23.4
10.3
10.3
8.0
8.0
r r
23.5
23.6
10.2
10.2
8.0
8.0
r r
23.7
10.2
8.0
r r
23.8
10.2
8.0
r r
23.9
10.2
8.0
r r
a r
LF
a r
24.0
10.1
8.0
r r
24.1
10.1
8.0
r r
24.2
10.1
8.0
r r
24.3
24.4
10.1
10.1
8.0
8.0
r r
24.5
24.6
11.7
11.7
9.0
9.0
r r
24.7
11.7
9.0
r r
24.8
11.7
9.0
r r
24.9
11.7
9.0
r r
a r
a r
25.0
11.6
9.0
r r
25.1
11.6
9.0
r r
25.2
11.6
9.0
r r
25.3
25.4
11.6
11.6
9.0
9.0
r r
25.5
25.6
11.5
11.5
9.0
9.0
r r
25.7
11.5
9.0
r r
25.8
11.5
9.0
r r
25.9
11.5
9.0
r r
a r
a r
26.0
11.4
9.0
r r
26.1
11.4
9.0
r r
26.2
11.4
9.0
r r
26.3
26.4
11.4
11.4
9.0
9.0
r r
26.5
26.6
11.3
11.3
9.0
9.0
r r
26.7
11.3
9.0
r r
26.8
11.3
9.0
r r
26.9
11.3
9.0
a r
27.0
11.2
9.0
r r
27.1
11.2
9.0
r r
27.2
11.2
9.0
r r
27.3
27.4
11.2
11.2
9.0
9.0
r r
a r
r r
TAWSN
2300S25
TAWMN
2300S25
TAWLN
2300S25
TAWSN
2400S32
TAWMN
2400S32
TAWLN
2400S32
TAWSN
2500S32
TAWMN
2500S32
TAWLN
2500S32
TAWSN
2600S32
TAWMN
2600S32
Stock
Order Number
TAWNH2750T
TAWNH2760T
TAWNH2770T
TAWNH2780T
TAWNH2790T
TAWNH2800T
TAWNH2810T
TAWNH2820T
TAWNH2830T
TAWNH2840T
TAWNH2850T
TAWNH2860T
TAWNH2870T
TAWNH2880T
TAWNH2890T
TAWNH2900T
TAWNH2910T
TAWNH2920T
TAWNH2930T
TAWNH2940T
TAWNH2950T
TAWNH2960T
TAWNH2970T
TAWNH2980T
TAWNH2990T
TAWNH3000T
TAWNH3010T
TAWNH3020T
TAWNH3030T
TAWNH3040T
Dimensions (mm)
DC
a r
27.5
12.3
10.0
r r
27.6
12.3
10.0
r r
27.7
12.3
10.0
r r
27.8
12.3
10.0
r r
27.9
12.3
10.0
a r
28.0
12.2
10.0
r r
28.1
12.2
10.0
r r
28.2
12.2
10.0
r r
28.3
28.4
12.2
12.2
10.0
10.0
r r
28.5
28.6
12.1
12.1
10.0
10.0
r r
28.7
12.1
10.0
r r
28.8
12.1
10.0
r r
28.9
12.1
10.0
a r
29.0
12.0
10.0
r r
29.1
12.0
10.0
r r
29.2
12.0
10.0
r r
29.3
29.4
12.0
12.0
10.0
10.0
r r
29.5
29.6
11.9
11.9
10.0
10.0
r r
29.7
11.9
10.0
r r
29.8
11.9
10.0
r r
29.9
11.9
10.0
a r
30.0
11.8
10.0
r r
30.1
11.8
10.0
r r
30.2
11.8
10.0
r r
30.3
30.4
11.8
11.8
10.0
10.0
r r
a r
r r
a r
r r
LF
Applicable
Holder
TAWSN
2800S32
TAWMN
2800S32
TAWLN
2800S32
TAWSN
2900S32
TAWMN
2900S32
TAWLN
2900S32
TAWSN
3000S32
TAWMN
3000S32
TAWLN
3000S32
TAWLN
2600S32
TAWSN
2700S32
TAWMN
2700S32
DRILLING
DC
Applicable
Holder
VP15TF
VP10H
TAWNH2300T
TAWNH2310T
TAWNH2320T
TAWNH2330T
TAWNH2340T
TAWNH2350T
TAWNH2360T
TAWNH2370T
TAWNH2380T
TAWNH2390T
TAWNH2400T
TAWNH2410T
TAWNH2420T
TAWNH2430T
TAWNH2440T
TAWNH2450T
TAWNH2460T
TAWNH2470T
TAWNH2480T
TAWNH2490T
TAWNH2500T
TAWNH2510T
TAWNH2520T
TAWNH2530T
TAWNH2540T
TAWNH2550T
TAWNH2560T
TAWNH2570T
TAWNH2580T
TAWNH2590T
TAWNH2600T
TAWNH2610T
TAWNH2620T
TAWNH2630T
TAWNH2640T
TAWNH2650T
TAWNH2660T
TAWNH2670T
TAWNH2680T
TAWNH2690T
TAWNH2700T
TAWNH2710T
TAWNH2720T
TAWNH2730T
TAWNH2740T
Dimensions (mm)
VP15TF
VP10H
Stock
Order Number
TAWLN
2700S32
N235
CARBIDE
TAW
H Type
(Cast Iron)
140
DC(h7)
INSERTS
TAWKH1400TG
TAWKH1410TG
TAWKH1420TG
TAWKH1430TG
TAWKH1440TG
TAWKH1450TG
TAWKH1460TG
TAWKH1470TG
TAWKH1480TG
TAWKH1490TG
TAWKH1500TG
TAWKH1510TG
TAWKH1520TG
TAWKH1530TG
TAWKH1540TG
TAWKH1550TG
TAWKH1560TG
TAWKH1570TG
TAWKH1580TG
TAWKH1590TG
TAWKH1600TG
TAWKH1610TG
TAWKH1620TG
TAWKH1630TG
TAWKH1640TG
TAWKH1650TG
TAWKH1660TG
TAWKH1670TG
TAWKH1680TG
TAWKH1690TG
TAWKH1700TG
TAWKH1710TG
TAWKH1720TG
TAWKH1730TG
TAWKH1740TG
TAWKH1750TG
TAWKH1760TG
TAWKH1770TG
TAWKH1780TG
TAWKH1790TG
TAWKH1800TG
TAWKH1810TG
TAWKH1820TG
TAWKH1830TG
TAWKH1840TG
DC
LF
14.0
14.1
7.1
7.1
5.0
5.0
14.2
7.1
5.0
14.3
14.4
7.1
7.1
5.0
5.0
14.5
14.6
7.0
7.0
5.0
5.0
14.7
7.0
5.0
14.8
7.0
5.0
14.9
7.0
5.0
15.0
6.9
5.0
15.1
6.9
5.0
15.2
6.9
5.0
15.3
15.4
6.9
6.9
5.0
5.0
15.5
15.6
7.3
7.3
6.0
6.0
15.7
7.3
6.0
15.8
7.3
6.0
15.9
7.3
6.0
16.0
7.2
6.0
16.1
7.2
6.0
16.2
7.2
6.0
16.3
16.4
7.2
7.2
6.0
6.0
16.5
16.6
7.1
7.1
6.0
6.0
16.7
7.1
6.0
16.8
7.1
6.0
16.9
7.1
6.0
17.0
7.0
6.0
17.1
7.0
6.0
17.2
7.0
6.0
17.3
17.4
7.0
7.0
6.0
6.0
17.5
17.6
6.8
6.8
6.0
6.0
17.7
6.8
6.0
17.8
6.8
6.0
17.9
6.8
6.0
18.0
6.8
6.0
18.1
6.8
6.0
18.2
6.8
6.0
18.3
18.4
6.8
6.8
6.0
6.0
[
[
[
[
[
[
[
[
Applicable
Holder
TAWSNH
1400S16
TAWMNH
1400S16
TAWLNH
1400S16
TAWSNH
1500S20
TAWMNH
1500S20
TAWLNH
1500S20
TAWSN
1600S20
TAWMN
1600S20
TAWLN
1600S20
TAWSN
1700S20
TAWMN
1700S20
TAWLN
1700S20
TAWSN
1800S20
TAWMN
1800S20
TAWLN
1800S20
Stock
Order Number
TAWKH1850TG
TAWKH1860TG
TAWKH1870TG
TAWKH1880TG
TAWKH1890TG
TAWKH1900TG
TAWKH1910TG
TAWKH1920TG
TAWKH1930TG
TAWKH1940TG
TAWKH1950TG
TAWKH1960TG
TAWKH1970TG
TAWKH1980TG
TAWKH1990TG
TAWKH2000TG
TAWKH2010TG
TAWKH2020TG
TAWKH2030TG
TAWKH2040TG
TAWKH2050TG
TAWKH2060TG
TAWKH2070TG
TAWKH2080TG
TAWKH2090TG
TAWKH2100TG
TAWKH2110TG
TAWKH2120TG
TAWKH2130TG
TAWKH2140TG
TAWKH2150TG
TAWKH2160TG
TAWKH2170TG
TAWKH2180TG
TAWKH2190TG
TAWKH2200TG
TAWKH2210TG
TAWKH2220TG
TAWKH2230TG
TAWKH2240TG
TAWKH2250TG
TAWKH2260TG
TAWKH2270TG
TAWKH2280TG
TAWKH2290TG

Inventory maintained in Japan. To be replaced by new products.
a
N236
Dimensions (mm)
[:
Dimensions (mm)
DP5010
DP5010
DRILLING
Stock
Order Number
LF
DC
LF
18.5
8.6
7.0
18.6
8.6
7.0
18.7
8.6
7.0
18.8
8.6
7.0
18.9
8.6
7.0
19.0
8.5
7.0
19.1
8.5
7.0
19.2
8.5
7.0
19.3
19.4
8.5
8.5
7.0
7.0
19.5
19.6
8.4
8.4
7.0
7.0
19.7
8.4
7.0
19.8
8.4
7.0
19.9
8.4
7.0
20.0
8.3
7.0
20.1
8.3
7.0
20.2
8.3
7.0
20.3
20.4
8.3
8.3
7.0
7.0
20.5
20.6
8.2
8.2
7.0
7.0
20.7
8.2
7.0
20.8
8.2
7.0
20.9
8.2
7.0
21.0
8.1
7.0
21.1
8.1
7.0
21.2
8.1
7.0
21.3
21.4
8.1
8.1
7.0
7.0
21.5
21.6
9.8
9.8
8.0
8.0
21.7
9.8
8.0
21.8
9.8
8.0
21.9
9.8
8.0
22.0
9.7
8.0
22.1
9.7
8.0
22.2
9.7
8.0
22.3
22.4
9.7
9.7
8.0
8.0
22.5
22.6
9.6
9.6
8.0
8.0
22.7
9.6
8.0
22.8
22.9
9.6
9.6
8.0
8.0
a
a
r
a
r
a
r
a
Applicable
Holder
TAWSN
1900S25
TAWMN
1900S25
TAWLN
1900S25
TAWSN
2000S25
TAWMN
2000S25
TAWLN
2000S25
TAWSN
2100S25
TAWMN
2100S25
TAWLN
2100S25
TAWSN
2200S25
TAWMN
2200S25
TAWLN
2200S25
TAWSN
2300S25
TAWMN
2300S25
TAWLN
2300S25
CARBIDE
23.0
9.5
8.0
23.1
9.5
8.0
23.2
9.5
8.0
23.3
23.4
9.5
9.5
8.0
8.0
23.5
23.6
9.4
9.4
8.0
8.0
23.7
9.4
8.0
23.8
9.4
8.0
23.9
9.4
8.0
r
a
LF
24.0
9.3
8.0
24.1
9.3
8.0
24.2
9.3
8.0
24.3
24.4
9.3
9.3
8.0
8.0
24.5
24.6
10.8
10.8
9.0
9.0
24.7
10.8
9.0
24.8
10.8
9.0
24.9
10.8
9.0
r
a
25.0
10.7
9.0
25.1
10.7
9.0
25.2
10.7
9.0
25.3
25.4
10.7
10.7
9.0
9.0
25.5
25.6
10.6
10.6
9.0
9.0
25.7
10.6
9.0
25.8
10.6
9.0
25.9
10.6
9.0
r
a
26.0
10.5
9.0
26.1
10.5
9.0
26.2
10.5
9.0
26.3
26.4
10.5
10.5
9.0
9.0
26.5
26.6
10.4
10.4
9.0
9.0
26.7
10.4
9.0
26.8
10.4
9.0
26.9
10.4
9.0
27.0
10.3
9.0
27.1
10.3
9.0
27.2
10.3
9.0
27.3
27.4
10.3
10.3
9.0
9.0
r
a
TAWSN
2300S25
TAWMN
2300S25
TAWLN
2300S25
TAWSN
2400S32
TAWMN
2400S32
TAWLN
2400S32
TAWSN
2500S32
TAWMN
2500S32
TAWLN
2500S32
TAWSN
2600S32
TAWMN
2600S32
Stock
Order Number
TAWKH2750TG
TAWKH2760TG
TAWKH2770TG
TAWKH2780TG
TAWKH2790TG
TAWKH2800TG
TAWKH2810TG
TAWKH2820TG
TAWKH2830TG
TAWKH2840TG
TAWKH2850TG
TAWKH2860TG
TAWKH2870TG
TAWKH2880TG
TAWKH2890TG
TAWKH2900TG
TAWKH2910TG
TAWKH2920TG
TAWKH2930TG
TAWKH2940TG
TAWKH2950TG
TAWKH2960TG
TAWKH2970TG
TAWKH2980TG
TAWKH2990TG
TAWKH3000TG
TAWKH3010TG
TAWKH3020TG
TAWKH3030TG
TAWKH3040TG
Dimensions (mm)
DC
27.5
11.3
10.0
27.6
11.3
10.0
27.7
11.3
10.0
27.8
11.3
10.0
27.9
11.3
10.0
28.0
11.2
10.0
28.1
11.2
10.0
28.2
11.2
10.0
28.3
28.4
11.2
11.2
10.0
10.0
28.5
28.6
11.1
11.1
10.0
10.0
28.7
11.1
10.0
28.8
11.1
10.0
28.9
11.1
10.0
29.0
11.0
10.0
29.1
11.0
10.0
29.2
11.0
10.0
29.3
29.4
11.0
11.0
10.0
10.0
29.5
29.6
10.9
10.9
10.0
10.0
29.7
10.9
10.0
29.8
10.9
10.0
29.9
10.9
10.0
30.0
10.8
10.0
30.1
10.8
10.0
30.2
10.8
10.0
30.3
30.4
10.8
10.8
10.0
10.0
r
a
r
a
LF
Applicable
Holder
TAWSN
2800S32
TAWMN
2800S32
TAWLN
2800S32
TAWSN
2900S32
TAWMN
2900S32
TAWLN
2900S32
TAWSN
3000S32
TAWMN
3000S32
TAWLN
3000S32
TAWLN
2600S32
TAWSN
2700S32
TAWMN
2700S32
DRILLING
DC
Applicable
Holder
DP5010
TAWKH2300TG
TAWKH2310TG
TAWKH2320TG
TAWKH2330TG
TAWKH2340TG
TAWKH2350TG
TAWKH2360TG
TAWKH2370TG
TAWKH2380TG
TAWKH2390TG
TAWKH2400TG
TAWKH2410TG
TAWKH2420TG
TAWKH2430TG
TAWKH2440TG
TAWKH2450TG
TAWKH2460TG
TAWKH2470TG
TAWKH2480TG
TAWKH2490TG
TAWKH2500TG
TAWKH2510TG
TAWKH2520TG
TAWKH2530TG
TAWKH2540TG
TAWKH2550TG
TAWKH2560TG
TAWKH2570TG
TAWKH2580TG
TAWKH2590TG
TAWKH2600TG
TAWKH2610TG
TAWKH2620TG
TAWKH2630TG
TAWKH2640TG
TAWKH2650TG
TAWKH2660TG
TAWKH2670TG
TAWKH2680TG
TAWKH2690TG
TAWKH2700TG
TAWKH2710TG
TAWKH2720TG
TAWKH2730TG
TAWKH2740TG
Dimensions (mm)
DP5010
Stock
Order Number
TAWLN
2700S32
N237
CARBIDE
TAW
& 14.0 & 15.4
Drill Diameter
Work Material
M
K

(m/min)
Hardness
70(60 90)
Feed
(mm/rev)
Cutting Speed
(m/min)
Feed
(mm/rev)
0.20 (0.15 0.25)
80 (60 100)
0.25 (0.20 0.30)
90 (70 110)
0.25 (0.20 0.30)
< 180HB
Carbon Steel
Alloy Steel
180 280HB
70 (60 90)
0.20 (0.15 0.25)
80 (60 100)
0.25 (0.20 0.30)
80 (60 100)
0.25 (0.20 0.30)
280 350HB
60 (50 80)
0.15 (0.12 0.18)
70 (50 90)
0.20 (0.15 0.25)
70 (50 90)
0.20 (0.15 0.25)
Stainless Steel
< 200HB
50 (40 60)
0.15 (0.12 0.18)
50 (40 60)
0.15 (0.12 0.18)
60 (50 70)
0.20 (0.15 0.22)
Gray Cast Iron
Tensile Strength
70 (50 90)
0.20 (0.15 0.25)
100 (60 120)
0.25 (0.20 0.30)
120 (60 140)
0.25 (0.20 0.30)
Ductile Cast Iron
Tensile Strength
70 (50 90)
0.20 (0.15 0.25)
80 (60 90)
0.25 (0.20 0.30)
80 (60 90)
0.25 (0.20 0.30)
< 350MPa
< 450MPa
& 21.5 & 24.4
Drill Diameter

(m/min)
Hardness
& 24.5 & 27.4
Feed
(mm/rev)
& 27.5 & 30.4
Cutting Speed
(m/min)
Feed
(mm/rev)
Cutting Speed
(m/min)
Feed
(mm/rev)
Mild Steel
< 180HB
100 (80 120)
0.30 (0.25 0.35)
110 (80 120)
0.30 (0.25 0.35)
110 (80 120)
0.30 (0.25 0.35)
Carbon Steel
Alloy Steel
180 280HB
90 (70 110)
0.30 (0.25 0.35)
100 (80 120)
0.30 (0.25 0.35)
100 (80 120)
0.30 (0.25 0.35)
280 350HB
80 (60 100)
0.25 (0.20 0.30)
90 (70 110)
0.25 (0.20 0.30)
90 (70 110)
0.25 (0.20 0.30)
Stainless Steel
< 200HB
60 (50 70)
0.20 (0.15 0.22)
70 (60 80)
0.25 (0.20 0.28)
70 (60 80)
0.25 (0.20 0.28)
Tensile Strength 130 (80 150)

< 350MPa
0.35 (0.25 0.40)
140 (90 160)
0.35 (0.25 0.40)
140 (90 160)
0.40 (0.30 0.45)
Tensile Strength
0.30 (0.25 0.35)
100 (80 110)
0.30 (0.25 0.35)
100 (80 110)
0.30 (0.25 0.35)
& 18.5 & 21.4
Cutting Speed
(m/min)
Mild Steel
Work Material
& 15.5 & 18.4
Feed
(mm/rev)
Gray Cast Iron

Ductile Cast Iron
< 450MPa
90 (60 100)
(Note 1) When using the 8DC type holder, reduce the cutting speed by approx. 20%.
(Note 2) When using the 8DC type holder, it is recommended to drill a pilot guide hole.
(Note 3) H type honing is recommended when machining mild steel and stainless steel.
y HONE WIDTH
If an insert with honing other than standard is needed, please order
using the symbols below.
(Honing Standard)
(Insert Order Number)
H : H Type
TAW
Product Name
N : General Use
K : For Cast Iron
B : For Bridges
Honing Symbol
Insert Diameter
Honing Type
Honing Type
Hone Width (mm)
F
G
H
-(Standard)
K
S
M
0
0.02 0.05
0.05 0.10
0.10 0.15
0.15 0.20
0.20 0.25
0.25 0.30
NOTES ON USE
DRILLING
y INSERT INSTALLATION
aLoosen the clamp screw to install the insert.
aCorrectly mesh the insert and the holder serrations, then slide the insert to the bottom of the slot.
aFasten the clamp screw using the torque wrench provided while holding the insert lightly as shown. (Figure 1)
aCheck there is no gap between the bottom of the insert and holder. (Figure 2)

Drill Diameter (mm)
Clamp Torque (N m)
14 15
16 18
19 21
22 24
25 27
28 30
2.0
2.0
3.5
5.5
8.5
12.0
Fig. 1
INSERT REPLACEMENT
aThouroughly clean the serrations of the holder before installing a new insert.
Remove heavy dirt in the holder serrations by using the cleaning plate provided.
N238
Fig. 2
Clearance
TAW
P
CARBIDE
Steel
(For Bridge Construction)
DCON
LF
150
DC
PL
LU
LH
OAL
24.5
24.6
24.7
26.5
26.7
Insert
Stock
Order Number
DC
Order Number
(mm)
TAWSB2500S32
TAWMB2500S32
TAWSB2700S32
Dimensions (mm)
TAWMB2700S32
VP15TF
(mm)
(l/d)
Holder
Stock
DC
Hole Depth
y HOLDERS
LU
91.9 113.9 173.9 170.6
3.3
32
Clamp Wrench Plate Anti-seize

Screw
Lubricant
WS406023T TKY25T WPT4405 MK1KS
143.9 168.9 228.9 225.6
3.3
32
98.2 119.2 179.2 175.6
3.6
32
155.2 179.2 239.2 235.6
3.6
32
TAWBH2450T
TAWBH2460T
TAWBH2470T
TAWBH2650T
TAWB2670T
TAWBH2670T
24.5
24.6
24.7
26.5
26.7
r
a
r
a
a
LH
OAL
LF
PL DCON
(Note 1) The above dimensions are for when installing the TAWBH (H type) insert.
INSERTS
LF
24.5
11.7
9.0
TAWBH2460T
24.6
11.7
9.0
TAWBH2470T
24.7
11.7
9.0
TAWBH2650T
26.5
11.3
9.0
TAWBH2670T
26.7
11.3
9.0
TAWBH2450T
Applicable Holder
Hone Width
(mm)
Geometry
TAWSB2500S32
TAWMB2500S32
0.200.25
TAWSB2700S32
TAWMB2700S32
150
DC
Order Number
DC(h8)
H Type
Dimensions (mm)
VP15TF
Stock
Shape
LF

P
Structural
Steel
SS400
(JIS)
SM490
(JIS)
SM570
(JIS)
& 24.5, & 24.6, & 24.7

(m/min)
Hardness
Tensile Strength
< 400 500MPa
70 (60 80)
& 26.5, & 26.7
Feed
(mm/rev)
Cutting Speed
(m/min)
Feed
(mm/rev)
0.30 (0.25 0.35)
70 (60 80)
0.30 (0.25 0.35)
Tensile Strength
< 490 610MPa
65 (55 75)
0.30 (0.25 0.35)
65 (55 75)
0.30 (0.25 0.35)
Tensile Strength
60 (50 70)
0.30 (0.25 0.35)
60 (50 70)
0.30 (0.25 0.35)
< 570 720MPa
DRILLING
Drill Diameter
Work Material
N239
CARBIDE
TAFS/TAFM/TAFL
P
Steel
a High rigidity holder.

a 4 corner use insert.
a Various grades and chip breakers.
DCON
DC
LU
LPR
DCSFMS
CNT (Thread hole, Coolant hole type)
DC
OAL
*A screw hole on the flange section is not a coolant hole.

Number of Teeth = 4 (& DC > 49)
DRILLING
(mm)
(l/d)
12.0
2
3
12.5
2
3
13.0
2
3
13.5
2
3
14.0
2
3
14.5
2
3
15.0
2
3
15.5
2
3
16.0
2
3
4
16.5
2
3
17.0
2
3
4
17.5
2
3
18.0
2
3
4
18.5
N240
2
3
Order Number
TAFS1200F20
TAFM1200F20
TAFS1250F20
TAFM1250F20
TAFS1300F20
TAFM1300F20
TAFS1350F20
TAFM1350F20
TAFS1400F20
TAFM1400F20
TAFS1450F20
TAFM1450F20
TAFS1500F20
TAFM1500F20
TAFS1550F20
TAFM1550F20
TAFS1600F25
TAFM1600F25
TAFL1600F25
TAFS1650F25
TAFM1650F25
TAFS1700F25
TAFM1700F25
TAFL1700F25
TAFS1750F25
TAFM1750F25
TAFS1800F25
TAFM1800F25
TAFL1800F25
TAFS1850F25
TAFM1850F25
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Number
of Teeth
Dimensions (mm)
Stock
DC
Hole
Depth
LU
LPR OAL DCON DCSFMS CNT
Insert Number
Clamp Screw
Wrench
2
2
29
41
39
51
82
94
20
20
25
25
PT1/8 GCMT040204-Up
PT1/8 GCMT040204-Up
TS2
TKY06F
TS2
TKY06F
2
2
29
41
39
51
82
94
20
20
25
25
PT1/8 GCMT040204-Up
PT1/8 GCMT040204-Up
TS2
TKY06F
TS2
TKY06F
2
2
31
44
41
54
84
97
20
20
25
25
PT1/8 GCMT040204-Up
PT1/8 GCMT040204-Up
TS2
TKY06F
TS2
TKY06F
2
2
31
44
41
54
84
97
20
20
25
25
PT1/8 GCMT040204-Up
PT1/8 GCMT040204-Up
TS2
TKY06F
TS2
TKY06F
2
2
33
47
43
57
86
100
20
20
25
25
PT1/8 GCMT040204-Up
PT1/8 GCMT040204-Up
TS2
TKY06F
TS2
TKY06F
2
2
33
47
43
57
86
100
20
20
25
25
PT1/8 GCMT040204-Up
PT1/8 GCMT040204-Up
TS2
TKY06F
TS2
TKY06F
2
2
35
50
45
60
88
103
20
20
25
25
PT1/8 GPMT060204-Up
PT1/8 GPMT060204-Up
TS2
TKY06F
TS2
TKY06F
2
2
35
50
45
60
88
103
20
20
25
25
PT1/8 GPMT060204-Up
PT1/8 GPMT060204-Up
TS2
TKY06F
TS2
TKY06F
2
2
2
38
54
70
57
73
89
107
123
139
25
25
25
35
35
35
PT1/8 GPMT060204-Up
PT1/8 GPMT060204-Up
PT1/8 GPMT060204-Up
TS2
TKY06F
TS2
TKY06F
TS2
TKY06F
2
2
38
54
57
73
107
123
25
25
35
35
PT1/8 GPMT060204-Up
PT1/8 GPMT060204-Up
TS2
TKY06F
TS2
TKY06F
2
2
2
41
58
75
59
76
93
109
126
143
25
25
25
35
35
35
PT1/8 GPMT060204-Up
PT1/8 GPMT060204-Up
PT1/8 GPMT060204-Up
TS2
TKY06F
TS2
TKY06F
TS2
TKY06F
2
2
41
58
59
76
109
126
25
25
35
35
PT1/8 GPMT060204-Up
PT1/8 GPMT060204-Up
TS2
TKY06F
TS2
TKY06F
2
2
2
43
61
79
61
79
97
111
129
147
25
25
25
35
35
35
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
2
2
43
61
61
79
111
129
25
25
35
35
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
TS25
TKY08F
TS25
TKY08F
CARBIDE
(l/d)
19.0
2
3
4
19.5
2
3
20.0
2
3
4
20.5
2
3
21.0
2
3
4
21.5
2
3
22.0
2
3
4
22.5
2
3
23.0
2
3
4
23.5
2
3
24.0
2
3
4
24.5
2
3
25.0
2
3
4
25.5
2
3
26.0
2
3
4
26.5
2
3
27.0
2
3
4
27.5
2
3
28.0
2
3
4
TAFS1900F25
TAFM1900F25
TAFL1900F25
TAFS1950F25
TAFM1950F25
TAFS2000F25
TAFM2000F25
TAFL2000F25
TAFS2050F25
TAFM2050F25
TAFS2100F25
TAFM2100F25
TAFL2100F25
TAFS2150F25
TAFM2150F25
TAFS2200F25
TAFM2200F25
TAFL2200F25
TAFS2250F25
TAFM2250F25
TAFS2300F25
TAFM2300F25
TAFL2300F25
TAFS2350F25
TAFM2350F25
TAFS2400F25
TAFM2400F25
TAFL2400F25
TAFS2450F25
TAFM2450F25
TAFS2500F32
TAFM2500F32
TAFL2500F32
TAFS2550F32
TAFM2550F32
TAFS2600F32
TAFM2600F32
TAFL2600F32
TAFS2650F32
TAFM2650F32
TAFS2700F32
TAFM2700F32
TAFL2700F32
TAFS2750F32
TAFM2750F32
TAFS2800F32
TAFM2800F32
TAFL2800F32
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Number
of Teeth
Order Number
LU
Insert Number
Clamp Screw
Wrench
2
2
2
46
65
84
63
82
101
113
132
151
25
25
25
35
35
35
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
TS25
zTKY08F
TS25
zTKY08F
TS25
zTKY08F
2
2
46
65
63
82
113
132
25
25
35
35
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
TS25
zTKY08F
TS25
zTKY08F
2
2
2
48
68
88
65
85
105
115
135
155
25
25
25
35
35
35
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
TS25
zTKY08F
TS25
zTKY08F
TS25
zTKY08F
2
2
48
68
65
85
115
135
25
25
35
35
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
TS25
zTKY08F
TS25
zTKY08F
2
2
2
50
71
92
67
88
109
117
138
159
25
25
25
35
35
35
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
TS25
zTKY08F
TS25
zTKY08F
TS25
zTKY08F
2
2
50
71
67
88
117
138
25
25
35
35
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
TS25
zTKY08F
TS25
zTKY08F
2
2
2
53
75
97
69
91
113
119
141
163
25
25
25
35
35
35
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
TS25
zTKY08F
TS25
zTKY08F
TS25
zTKY08F
2
2
53
75
69
91
119
141
25
25
35
35
PT1/8 GPMT070204-Up
PT1/8 GPMT070204-Up
TS25
zTKY08F
TS25
zTKY08F
2
2
2
55
78
101
71
94
117
121
144
167
25
25
25
35
35
35
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
TS3
zTKY08F
TS3
zTKY08F
TS3
zTKY08F
GPMT090304-Up
zTKY08F
2
2
55
78
71
94
121
144
25
25
35
35
PT1/8
PT1/8 GPMT090304-Up
TS3
TS3
zTKY08F
2
2
2
58
82
106
73
97
121
123
147
171
25
25
25
35
35
35
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
TS3
zTKY08F
TS3
zTKY08F
TS3
zTKY08F
2
2
58
82
73
97
123
147
25
25
35
35
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
TS3
zTKY08F
TS3
zTKY08F
2
2
2
60
85
110
75
100
125
130
155
180
32
32
32
42
42
42
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
TS3
zTKY08F
TS3
zTKY08F
TS3
zTKY08F
2
2
60
85
75
100
130
155
32
32
42
42
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
TS3
zTKY08F
TS3
zTKY08F
2
2
2
62
88
114
77
103
129
132
158
184
32
32
32
42
42
42
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
TS3
zTKY08F
TS3
zTKY08F
TS3
zTKY08F
2
2
62
88
77
103
132
158
32
32
42
42
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
TS3
zTKY08F
TS3
zTKY08F
2
2
2
65
92
119
79
106
133
134
161
188
32
32
32
42
42
42
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
TS3
zTKY08F
TS3
zTKY08F
TS3
zTKY08F
2
2
65
92
79
106
134
161
32
32
42
42
PT1/8 GPMT090304-Up
PT1/8 GPMT090304-Up
TS3
zTKY08F
TS3
zTKY08F
2
2
2
67
95
123
81
109
137
136
164
192
32
32
32
42
42
42
PT1/8 GPMT11T308-Up
PT1/8 GPMT11T308-Up
PT1/8 GPMT11T308-Up
TS4
xTKY15D
TS4
xTKY15D
TS4
xTKY15D
INSERT DESCRIPTION
CUTTING CONDITIONS
N244
N245
USAGE NOTE
TECHNICAL DATA
N248
Q001
DRILLING
(mm)
Dimensions (mm)
Stock
DC
Hole
Depth
N241
TAFS/TAFM/TAFL
(mm)
(l/d)
28.5
2
3
29.0
2
3
4
29.5
2
3
30.0
2
3
4
31.0
32.0
33.0
DRILLING
34.0
2
3
4
2
3
4
2
3
4
35.0
2
3
36.0
2
3
37.0
2
3
38.0
2
3
39.0
2
3
40.0
2
3
41.0
2
3
42.0
2
3
43.0
2
3
44.0
2
3
45.0
2
3
46.0
2
3
47.0
2
3
48.0
2
3
N242
2
3
4
Dimensions (mm)
Order Number
TAFS2850F32
TAFM2850F32
TAFS2900F32
TAFM2900F32
TAFL2900F32
TAFS2950F32
TAFM2950F32
TAFS3000F40
TAFM3000F40
TAFL3000F40
TAFS3100F40
TAFM3100F40
TAFL3100F40
TAFS3200F40
TAFM3200F40
TAFL3200F40
TAFS3300F40
TAFM3300F40
TAFL3300F40
TAFS3400F40
TAFM3400F40
TAFL3400F40
TAFS3500F40
TAFM3500F40
TAFS3600F40
TAFM3600F40
TAFS3700F40
TAFM3700F40
TAFS3800F40
TAFM3800F40
TAFS3900F40
TAFM3900F40
TAFS4000F40
TAFM4000F40
TAFS4100F40
TAFM4100F40
TAFS4200F40
TAFM4200F40
TAFS4300F40
TAFM4300F40
TAFS4400F40
TAFM4400F40
TAFS4500F40
TAFM4500F40
TAFS4600F40
TAFM4600F40
TAFS4700F40
TAFM4700F40
TAFS4800F40
TAFM4800F40
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Number
of Teeth
DC
Hole
Depth
Stock
CARBIDE
2
2
LU
67
95
81
109
136
164
32
32
Insert Number
Clamp Screw
Wrench
42
42
PT1/8 GPMT11T308-Up
PT1/8 GPMT11T308-Up
TS4
TKY15D
TS4
TKY15D
GPMT11T308-Up
2
2
2
70
99
128
83
112
141
138
167
196
32
32
32
42
42
42
PT1/8
PT1/8 GPMT11T308-Up
PT1/8 GPMT11T308-Up
TS4
TKY15D
TS4
TKY15D
TS4
TKY15D
2
2
70
99
83
112
138
167
32
32
42
42
PT1/8 GPMT11T308-Up
PT1/8 GPMT11T308-Up
TS4
TKY15D
TS4
TKY15D
GPMT11T308-Up
TKY15D
TS4
TKY15D
2
2
2
72
102
132
90
120
150
155
185
215
40
40
40
50
50
50
PT1/4
PT1/4 GPMT11T308-Up
PT1/4 GPMT11T308-Up
TS4
TS4
TKY15D
2
2
2
74
105
136
92
123
154
157
188
219
40
40
40
50
50
50
PT1/4 GPMT11T308-Up
PT1/4 GPMT11T308-Up
PT1/4 GPMT11T308-Up
TS4
TKY15D
TS4
TKY15D
TS4
TKY15D
2
2
2
77
109
141
94
126
158
159
191
223
40
40
40
50
50
50
PT1/4 GPMT11T308-Up
PT1/4 GPMT11T308-Up
PT1/4 GPMT11T308-Up
TS4
TKY15D
TS4
TKY15D
TS4
TKY15D
2
2
2
79
112
145
96
129
162
161
194
227
40
40
40
50
50
50
PT1/4 GPMT11T308-Up
PT1/4 GPMT11T308-Up
PT1/4 GPMT11T308-Up
TS4
TKY15D
TS4
TKY15D
TS4
TKY15D
2
2
2
82
116
150
98
132
166
163
197
231
40
40
40
50
50
50
PT1/4 GPMT11T308-Up
PT1/4 GPMT11T308-Up
PT1/4 GPMT11T308-Up
TS4
TKY15D
TS4
TKY15D
TS4
TKY15D
2
2
84
119
100
135
165
200
40
40
50
50
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
2
2
86
122
102
138
167
203
40
40
50
50
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
2
2
89
126
104
141
169
206
40
40
50
50
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
2
2
91
129
106
144
171
209
40
40
50
50
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
2
2
94
133
108
147
173
212
40
40
50
50
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
2
2
96
136
110
150
175
215
40
40
50
50
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
2
2
98
139
112
153
177
218
40
40
50
50
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
2
2
101
143
114
156
179
221
40
40
50
50
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
2
2
103
146
116
159
181
224
40
40
50
50
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
2
2
106
150
118
162
183
227
40
40
50
50
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
2
2
108
153
120
165
185
230
40
40
54
54
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
GPMT140408-Up
TKY25D
2
2
110
156
122
168
187
233
40
40
54
54
PT1/4
PT1/4 GPMT140408-Up
TS55
TS55
TKY25D
2
2
113
160
124
171
189
236
40
40
54
54
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
2
2
115
163
126
174
191
239
40
40
54
54
PT1/4 GPMT140408-Up
PT1/4 GPMT140408-Up
TS55
TKY25D
TS55
TKY25D
CARBIDE
49.0
2
3
50.0
2
3
51.0
2
3
52.0
2
3
53.0
2
3
54.0
2
3
55.0
2
3
56.0
2
3
TAFS4900F40
TAFM4900F40
TAFS5000F40
TAFM5000F40
TAFS5100F40
TAFM5100F40
TAFS5200F40
TAFM5200F40
TAFS5300F40
TAFM5300F40
TAFS5400F40
TAFM5400F40
TAFS5500F40
TAFM5500F40
TAFS5600F40
TAFM5600F40
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
LU
4
4
118
167
133
182
198
247
40
40
Insert Number
Clamp Screw
Wrench
58
58
PT1/4 GPMT090304-Up
PT1/4 GPMT090304-Up
TS3
TKY08F
TS3
TKY08F
GPMT090304-Up
4
4
120
170
135
185
200
250
40
40
58
58
PT1/4
PT1/4 GPMT090304-Up
TS3
TKY08F
TS3
TKY08F
4
4
122
173
137
188
202
253
40
40
58
58
PT1/4 GPMT090304-Up
PT1/4 GPMT090304-Up
TS3
TKY08F
TS3
TKY08F
4
4
125
177
139
191
204
256
40
40
58
58
PT1/4 GPMT090304-Up
PT1/4 GPMT090304-Up
TS3
TKY08F
TS3
TKY08F
4
4
127
180
141
194
206
259
40
40
63
63
PT1/4 GPMT090304-Up
PT1/4 GPMT090304-Up
TS3
TKY08F
TS3
TKY08F
4
4
128
182
143
197
208
262
40
40
63
63
PT1/4 GPMT090304-Up
PT1/4 GPMT090304-Up
TS3
TKY08F
TS3
TKY08F
4
4
130
185
145
200
210
265
40
40
63
63
PT1/4 GPMT090304-Up
PT1/4 GPMT090304-Up
TS3
TKY08F
TS3
TKY08F
4
4
132
188
147
203
212
268
40
40
63
63
PT1/4 GPMT090304-Up
PT1/4 GPMT090304-Up
TS3
TKY08F
TS3
TKY08F
DRILLING
(l/d)
Order Number
Number
of Teeth
(mm)
Dimensions (mm)
Stock
DC
Hole
Depth
INSERT DESCRIPTION
CUTTING CONDITIONS
N244
N245
USAGE NOTE
TECHNICAL DATA
N248
Q001
N243
CARBIDE
TAFS/TAFM/TAFL
INSERTS
Geometry
U1 Breaker
RE
GCMT
95 4
.7
60
100
GPMT
11
U2 Breaker
95 4
.7
RE
L
60
100
GPMT
11
U3 Breaker
RE
12 14.5
Dimensions (mm)
Stock
IC
RE
VP15TF UP20M GP20M UE6020 US735
GCMT040204-U1
5.0
2.38
0.4
15 17.5
GPMT060204-U1
5.56
2.38
0.4
18 22.5
GPMT070204-U1
6.35
2.38
0.4
23 27.5
49 56
GPMT090304-U1
7.94
3.18
0.4
28 34
GPMT11T308-U1
9.525
3.97
0.8
35 48
GPMT140408-U1
4.76
0.8
12 14.5
GCMT040204-U2
5.0
2.38
0.4
15 17.5
GPMT060204-U2
5.56
2.38
0.4
18 22.5
GPMT070204-U2
6.35
2.38
0.4
23 27.5
49 56
GPMT090304-U2
7.94
3.18
0.4
28 34
GPMT11T308-U2
9.525
3.97
0.8
35 48
GPMT140408-U2
12.70
4.76
0.8
15 17.5
GPMT060204-U3
5.56
2.38
0.4
18 22.5
GPMT070204-U3
6.35
2.38
0.4
23 27.5
49 56
GPMT090304-U3
7.94
3.18
0.4
28 34
GPMT11T308-U3
9.525
3.97
0.8
35 48
GPMT140408-U3
4.76
0.8
12.70
RE
IC
GPMT
Insert Number
RE
IC
GCMT
Drill Dia.
60
100
IC
11
S
12.70
INSERT RECOMMENDATION
y CHIP BREAKER RECOMMENDATION
e : 1st
Work Material P
M
Mild Steel
DRILLING
Breaker
Carbon Steel
Alloy Steel
GPMT
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
u
e : 1st
GCMT
Carbon Steel
Alloy Steel
Recommendation u : 2nd Recommendation
M
Mild Steel
Ductile Cast Iron
GCMT
y INSERT GRADE RECOMMENDATION
VP15TF
UP20M
GP20M
UE6020
US735
Gray Cast Iron
GPMT
Work Material P
N244
Stainless Steel
GCMT
U1
U2
U3
Grade
Recommendation u : 2nd Recommendation
Stainless Steel
Gray Cast Iron
Ductile Cast Iron
GPMT
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
GCMT
GPMT
CARBIDE

Work Material
Hardness
For l/d=2,3
(&12&14.5)
For l/d=4
(&16 )
(&15 )
Mild Steel
< 180HB
150
(100 200)
200
(150 300)
140
(100 200)
Feed (mm/rev)
Breaker
Drill Diameter (mm)

&12&14.5
180 280HB
120
(80 160)
150
(120 180)
100
(80 120)
180 280HB
120
(80 160)
150
(120 180)
100
(80 120)
Stainless Steel
< 200HB
100
(80 120)
150
(120 200)
110
(80 140)
0.06
0.08
0.10
0.12
0.10
(0.04 0.10) (0.04 0.12) (0.04 0.12) (0.04 0.14) (0.04 0.12)
Gray Cast Iron
Tensile
Strength
< 350MPa
120
(80 160)
150
(120 180)
140
(110 160)
0.06
0.09
0.12
0.15
0.12
(0.04 0.10) (0.06 0.12) (0.08 0.14) (0.08 0.18) (0.08 0.14)
U2
0.06
0.12
0.14
0.17
0.14
(0.04 0.10) (0.06 0.14) (0.08 0.18) (0.08 0.20) (0.08 0.18)
Tensile
Strength
< 450MPa
120
(80 150)
150
(120 180)
100
(80 120)
0.12
0.14
0.17
0.14
(0.06 0.14) (0.08 0.18) (0.08 0.20) (0.08 0.18)
U1
0.06
0.08
0.09
0.11
0.09
(0.04 0.10) (0.06 0.10) (0.06 0.12) (0.06 0.14) (0.06 0.12)
U2
0.06
0.10
0.12
0.14
0.12
(0.04 0.10) (0.06 0.12) (0.08 0.16) (0.08 0.18) (0.08 0.16)
0.10
0.12
0.14
0.12
(0.06 0.12) (0.08 0.16) (0.08 0.18) (0.08 0.16)
U1
0.07
0.07
0.08
0.10
0.08
(0.04 0.10) (0.04 0.10) (0.04 0.10) (0.04 0.12) (0.04 0.10)
U2
0.07
0.08
0.10
0.12
0.10
(0.04 0.10) (0.04 0.12) (0.04 0.14) (0.04 0.16) (0.04 0.14)
0.08
0.10
0.12
0.10
(0.04 0.12) (0.04 0.14) (0.04 0.16) (0.04 0.14)
U1
0.07
0.07
0.10
0.10
0.10
(0.06 0.10) (0.06 0.10) (0.04 0.14) (0.06 0.14) (0.06 0.14)
U2
0.07
0.15
0.20
0.20
0.20
(0.06 0.10) (0.10 0.18) (0.10 0.25) (0.10 0.25) (0.10 0.25)
U3
Ductile Cast
Iron
0.08
0.10
0.12
0.10
(0.04 0.12) (0.04 0.12) (0.04 0.14) (0.04 0.12)
U1
U3
& 49 &56
U2
U3
&35 & 48
0.06
0.07
0.08
0.10
0.08
(0.04 0.10) (0.04 0.10) (0.04 0.10) (0.04 0.12) (0.04 0.10)
U3
Alloy Steel
&23 &34
U1
U3
Carbon Steel
&15 &22.5
0.15
0.20
0.20
0.20
(0.10 0.18) (0.10 0.25) (0.10 0.25) (0.10 0.25)
U1
0.06
0.07
0.10
0.10
0.10
(0.04 0.10) (0.06 0.10) (0.06 0.14) (0.06 0.14) (0.06 0.14)
U2
0.06
0.12
0.15
0.18
0.15
(0.04 0.10) (0.08 0.14) (0.08 0.20) (0.08 0.20) (0.08 0.20)
U3
0.12
0.15
0.18
0.15
(0.08 0.14) (0.08 0.20) (0.08 0.20) (0.08 0.20)
DRILLING
(Note) When using drills for l/d= 4, the feed should be reduced to 80% of the above recommendations.
Workpiece : JIS SCM440(220HB) Cutting Speed : 150m/min Insert : U2 Breaker
Torque
100
16
80
Thrust
5.0
m
5m
0.1
60
40
rev
/
mm
.1
rev
f=0 6mm/
0
.
f=0
20
Drill Diameter (mm)
Thrust (kN)
v
/re
mm v
.15
e
r
0
/
m
f=
.1m
f=0
/rev
m
6m
f=0.0
f=
12
/re
20
Torque (Nm)
Power Consumption
v
/re /rev
mm mm
5
0.1 0.1
f= f= m/rev
m
.06
f=0
4.0
3.0
2.0
1.0
Drill Diameter (mm)
Drill Diameter (mm)
USAGE NOTE
TECHNICAL DATA
N248
Q001
N245
CARBIDE
JUST FIT SLEEVE
[JFS]
a A sleve designed to improve the performance of MVX/TAF drills, allowing the cutting diameter to be increased in increments of 0.1mm
a When intstalling on the drill shank the rotation axis of the drill is slightly decentered. It enables slight enlargement of the machined
S5
DCON
DCB
BD
hole. (enlargement range: 0.1-0.5mm)
L5
5
LF
*Increase : Size of the increase in the cutting diameter.
JFS-3
Suitable
MVX Type Drill
TAF Type Drill
DCON
DCB
LF
L5
33
25
20
43
30
0.10
33
25
20
43
30
0.20
MVX1700 X oF20
33
25
20
43
30
0.30
TAFS/M/L1200F20
33
25
20
43
30
0.40
TAFS/M/L1550F20
33
25
20
43
30
0.50
40
32
25
50
34
0.10
40
32
25
50
34
0.20
40
32
25
50
34
0.30
40
32
25
50
34
0.40
40
32
25
50
34
0.50
TAFS/M/L2450F25
48
40
32
55
40
0.10
MVX2600 X oF32
48
40
32
55
40
0.20
48
40
32
55
40
0.30
48
40
32
55
40
0.40
48
40
32
55
40
0.50
BD
JFS2520-10
JFS2520-20
JFS2520-30
JFS2520-40
JFS2520-50
JFS3225-10
JFS3225-20
JFS3225-30
JFS3225-40
JFS3225-50
JFS4032-10
JFS4032-20
JFS4032-30
JFS4032-40
JFS4032-50
MVX1750 X oF25
MVX2550 X oF25
TAFS/M/L1600F25
-
JFS-2
*Increase
(S52)
Stock
JFS-1
Dimensions (mm)
Individual Order Number
MVX3050 X oF32
TAFS/M/L2500F32
-
Set Order
Number
TAFS/M/L2950F32
(Note) Cannot be used for shank diameter 40.
y GUIDELINE FOR SELECTING A JUST FIT SLEEVE
DRILLING
Desired = (Drill&+ Increase of JFS) + 0.1mm

(Eg.) Desired diameter is 20.3mm (oversize is taken as 0.1mm).
20.3=(MVX2000 X oF25+JFS3225-20)+0.1
20mm Drill
Using JFS an Increase Oversize

of 0.2mm.
<Tool Selected>
Drill : MVX2000 X oF25
JUST FIT SLEEVE [JFS]
: JFS3225-20
(Note) Oversize can vary due to the cutting conditions used, please use the above as a guideline.
y ORDERING THE JUST FIT SLEEVE

aPurchasing Method 1
Oversize can vary due to the cutting conditions used.

Therefore it is recommended to purchase as a set.
When placing an order, please use the set order
number. (5 sleeves/set)
N246
aPurchasing Method 2
It is possible to order individually. When placing an
order, please use the individual order number.
CARBIDE
y APPLICATION OF JUST FIT SLEEVE

1 When inserting the drill into the side lock holder,
aligin the V groove on the outer peripheral edge
of the drill flange, as well as the round holes of the
outer peripheral edge of the sleeve flange and the
screws of the side lock holder for fixing the drill. (If
the drill does not have a V groove, align the notch
of the drill shank with the round holes of the sleeve.)
V Groove
Round Hole
Screw A
Side Lock Holder
2 Insert screws A of the side lock holder directly

to the open window of the sleeve and fix the
drill. Tighten screw B to a degree so as not to
damage the sleeve.
(Note)
Fine adjustments cannot be made for the
diameter
Cannot be used with collect chuck type holders.
Notch of Drill Shank
Screw B
y APPLICATION OF MVX TYPE DRILL

aUse on a Lathe
(1)The outer insert and machine X axis must be set parallel. The drill is designed so
that when the drill center and the machine spindle center are aligned then the inner
insert height is 0-0.15mm lower.
0 - 0.15
over center
Machineaxis
The inner insert may fracture if the center height of the inner insert is higher than
the machine X axis.
(2)By off setting it is possible to adjust the hole diameter. To do this adjust in the
positive X axis direction (hole oversize direction). For the amount of possible
adjustment please refer to the dimensions list.
X axis minus
X axis plus
Machineaxis
It is not recommended to adjust in the negative X axis direction as this may lead to
drill interference with the hole.
Cover
DRILLING
(3)When through hole drilling on a lathe the disc produced

by the drill exiting the workpiece may be expelled at high
velocity.
To reduce the danger of injury or damage a cover guard
is highly recommended.
N247
CARBIDE
JUST FIT SLEEVE
[JFS]
y APPLICATION OF TAF TYPE DRILL

aPlease ensure the highest rigidity possible exists in
both machine set up and workholding.
0.5
Coola
40
nt Pr
0.4
essu
re
30
0.3
0.2
0.1
20
lume
nt Vo
Coola
10
20
30
40
Drill Diameter (mm)
00.2mm
(1)The inner cutting edge must be positioned between 00.2mm over center.
Center Axis
Outer Edge
Inner Edge
Outer Edge
(2)To adjust the hole diameter by off-setting the drill, the outer cutting edge and
machine axis must be set parallel.
Machineaxis
Inner Edge
(3)When producing an oversize hole.

The drill offset should be no more than 2% of the diameter.
It is not possible to produce an undersized hole.
Cover
(4)When through hole drilling on a lathe the disc produced

by the drill exiting the workpiece may be expelled at
high velocity.
To reduce the danger of injury or damage a cover guard
is highly recommended.
Disc Shape Chip
DRILLING
50
Inner Edge Face
aUse on a Lathe
N248
Coolant Volume (l/min)
aCannot be used for stack drilling.

In common with many indexable insert drills, these drills
produce a round disc on exit which unless evacuated
may cause the drill to fracture.
50
0.6
Coolant Pressure (MPa)
aRefer to the following graph on the right for coolant

pressure and volume. Coolant is an important factor in
the efficient use of these drills.
0.7
GUN DRILL
CARBIDE
a GUN DRILL FOR MACHINING CENTER
Driver
Shank
a Suitable for deep hole drilling
on Machining Center.
DCON
DC(h8)
Insert
LH
a Drill Diameter :& 6.0 & 20.0
OAL
55
130
a GUN DRILL FOR GENERAL USE
DCON
DC 0.005
a Suitable for deep hole drilling.

a Drill Diameter : & 2.0 & 30.3
Driver
Shank
Insert
Insert Length
OAL
a SAMMIKA GUN DRILL
70
A Type Driver
B Type Driver
Driver
Shank
Insert
DCON
Insert Length
DCON
OAL
DCON
shape displays excellent chip dividing

and enables high feed machining.
70
DC 0.005
a The unique uneven cutting edge
DCON
DCON
Driver Type
70
70
B Type Driver
A Type Driver
a ARROW JET GUN DRILL

0
DCON
to the double-tooth design

and chip breaker.
DC 0.005
a Excellent chip discharge due
Driver
Shank
Insert
Insert Length
70
70
A Type Driver
70
B Type Driver
DRILLING
DCON
DCON
OAL
y ORDERING METHOD
Please specify the following when ordering.
zDrill Name xDiameter of Drill (DC) cLength of Drill (OAL) vOutside Diameter of Driver (DCON) and Type bWorkpiece Material,
Drilling Accuracy, Drilling Depth and Drilling Mode (Through Hole, Blind Hole)
e.g.) General Gun Drill &8 x 500 x &19.5 A type Driver, SCM440(250HB) x &80.020 300 x Through Hole
N249
CARBIDE
GUN REAMER
a Straight Reamer Type
a Reamer Diameter : & 6.0 & 30.0
a Number of teeth : 1, 2, 3, 4, 6
Insert
Driver
DC
DCON
Shank
OAL
a Spiral Reamer Type

a Number of teeth : 4, 6
Insert
Driver
DC
DCON
Shank
OAL
a Line Reamer Type

Shank
Insert
DCON

a Number of teeth : 1, 2, 4
DRILLING
OAL
y ORDERING METHOD
zReamer Name xDiameter of Reamer (DC) cLength of Reamer (OAL) vOutside Diameter of Driver (DCON) and Type
bNumber of Teeth nWorkpiece Material, Drilling Accuracy, Drilling Depth and Drilling Mode (Through Hole, Blind Hole)
e.g.) General Gun Reamer &12 x 450 x &19.5 A type Driver, 4-Teeth, FC250 (180HB) x &120.020 x 100 x Through Hole
N250
WITH DIAMOND COMPOUND
GUN REAMER
Driver
DC
DCON
Shank
Insert
CNT
CARBIDE
Insert Length
OAL
STANDARD
Insert Length Overall Length OAL Number of Teeth Shape of Teeth
Straight
6 30.3
Please contact us for any geometry (different diameter of reamer, insert length,
tool length, number of teeth) that is not in this list.
200
160
120
80
40
Driver hole diameter CNT External Diameter of Driver DCON
6.0<DC<7.0
3.5
12.70
7.0<DC<13.3
4.8
19.05
13.3<DC<20.8
6.4
25.40
20.8<DC<25.3
8.0
31.75
25.3<DC<30.3
8.0
38.10
Hydraulic (MPa)
Reamer Diameter DC
Discharge Amount (I/min)
Reamer Diameter
y COOLANT

Cutting Speed
(m/min)
150
Aluminium Alloy (
100 200)
130
Alloy Steel
(80 180)
5 10
0.08
(0.05 0.10)
0.03
(0.02 0.04)
Feed (mm/rev)
10 20
0.10
(0.05 0.15)
0.05
(0.03 0.06)
25 30
0.10
(0.05 0.15)
0.06
(0.04 0.07)
Reamer Diameter (mm)
DRILLING
Work Material
y ORDERING METHOD
zReamer Name xDiameter of Reamer (DC) cLength of Reamer (OAL) vNumber of Teeth bOutside Diameter of Driver (DCON) and Type
nWorkpiece Material, Drilling Accuracy, Drilling Depth and Drilling Mode (Through Hole, Blind Hole)
e.g.) Gun Reamer with Diamond Compound &10 x 300 1-Tooth x &19.05 A Type Driver, AC4B x &10 +0.01
x 200 x Through Hole
0
N251
CVD DIAMOND COATED DRILLS

CARBIDE
MCS
For CFRP
aFor high accuracy and efficient drilling of CFRP.

aUnique diamond coating produces excellent wear resistance and
smooth hole surface.
CFRP
CFRP with
Aluminium stack
3<DC<6 6<DC<10 10<DC<18 18<DC<20
CFRP/Titanium
Alloy stacks
0
0.018
0
0.008
h6
PL
0
0.027
0
0.011
0
0.033
0
0.013
LF
13
DCON(h6)
DC(h8)
0
0.022
0
0.009
LCF
LH
OAL
Internal Coolant
Stock
DC
Order Number
3
3
3
3
MCS01719X3DB
MCS01915X3DB
MCS02510X3DB
MCS03125X3DB
MCS03760X3DB
MCS03765X3DB
MCS04380X3DB
MCS05010X3DB
(l/d)
(inch)
(mm)
.1719
.1915
.2510
.3125
.3760
.3765
.4380
.5010
4.366
4.864
6.375
7.938
9.550
9.563
11.125
12.725
Dimensions (mm)
DD2010
Hole Depth
LCF
LH
OAL
LF
PL
24.0
28.1
DCON
29.0
29.1
66.0
66.1
65
65
1.0
1.1
6
6
34.5
42.5
79.5
78
1.5
41.9
42.9
79.9
78
1.9
47.2
48.2
89.2
87
2.2
10
47.2
48.2
89.2
87
2.2
10
55.6
61.0
56.6
62.0
102.6
108.0
100
105
2.6
3.0
12
14
(Note 1) MCS drills are suitable for use with shrink fit holders.
(Note 2) Please contact Mitsubishi Materials for special grades and geometries other than our standard products.
For non stocked sizes please enter details into the r below.
Please contact us for details of any geometry that is not mentioned.
*Recommended carbide grade TF15 for CFRP/titanium stacks.
MCr r r r r XrD r r r
Coolant
S : Int.
E : Ext.
Hole Depth (l/d)

Size range : 2-5
Shank Dia. DCON

Size range : 030-200
Drill Dia. DC
*Minimum diameter with internal coolant is &4mm (&.1575").
Size range of drill dia. : &3mm-&20mm

Size range of shank dia. : &3mm -&20mm
For cutting dia DC - Please indicate with 4 digits
E.g. &3mm - 0300
For shank dia DCON - Please use 3 digits
E.g. &12mm - 120
*For inch sizes please convert to metric
(1"= 25.4mm)
ex. : .3760"9.550mm0955
Coolant
S : Int.
E :Ext.
N252
Stepped Drill Dia. DC_2 Hole Depth (l/d)

Shank Dia. DCON
Size range : 2-5 Size range : 030-200
Drill Dia. DC
*Minimum diameter with internal coolant is &4mm (&.1575").
DC_2
DRILLING
MCr r r r r Xr r r r XrD r r r
DC(h8)
Order number of stepped type
DCON(h6)
Order number of straight type
CARBIDE

y DD2010
CFRP
CFRP with Aluminium stack
Work material
Dia.
DC
(inch)
Dia.
DC
(mm)
.1719
.1915
.251
.3125
.376
.3765
.438
.501
4.366
4.864
6.375
7.938
9.55
9.563
11.125
12.725
Feed rate
(min.max.)
(mm/rev)

(m/min)
(min-1)
85
85
95
95
95
95
100
100
6100
5500
4700
3800
3100
3100
2800
2500
0.04
0.04
0.05
0.05
0.07
0.07
0.1
0.1
(0.03 0.08)
(0.03 0.08)
(0.03 0.10)
(0.03 0.10)
(0.04 0.12)
(0.04 0.12)
(0.05 0.15)
(0.05 0.15)

(m/min)
(mm/min)
(min-1)
240
220
235
190
215
215
280
250
55
55
65
65
65
65
70
70
4000
3500
3200
2600
2100
2100
2000
1700
Feed rate
(min.max.)
(mm/rev)
0.04
0.04
0.05
0.05
0.06
0.06
0.07
0.08
(0.03 0.06)
(0.03 0.06)
(0.03 0.07)
(0.03 0.07)
(0.04 0.08)
(0.04 0.08)
(0.05 0.10)
(0.05 0.12)
Table Feed
(mm/min)
160
140
160
130
125
125
140
135
y TF15
CFRP with Titanium alloy stack
Work material
Dia.
DC
(mm)
.1719
.1915
.251
.3125
.376
.3765
.438
.501
4.366
4.864
6.375
7.938
9.55
9.563
11.125
12.725

(m/min)
(min-1)
8
8
8
8
10
10
10
10
500
500
300
300
300
300
200
200
Feed rate
(min.max.)
(mm/rev)
0.03
0.03
0.03
0.03
0.04
0.04
0.04
0.04
(0.02 0.04)
(0.02 0.04)
(0.02 0.04)
(0.02 0.04)
(0.03 0.05)
(0.03 0.05)
(0.03 0.05)
(0.03 0.05)
Table Feed
(mm/min)
15
15
5
5
10
10
5
5
DRILLING
Dia.
DC
(inch)
N253
DCSSS
Short, For non-ferrous material
CARBIDE
UWC
DC
130
135
Thinning
DC<1.5
DC>1.5
DC>1.5
0.2 < DC < 2
0
0.014
0
0.006
Non-ferrous Metal
h6
PL
DCON
DC
LF
LCF
OAL
a The original CVD diamond coating technology provides excellent
DCSSSD0020
DCSSSD0030
DCSSSD0040
DCSSSD0050
DCSSSD0060
DCSSSD0070
DCSSSD0080
DCSSSD0090
DCSSSD0100
DCSSSD0110
DC LCF OAL LF
PL DCON
0.2
0.3
2.05 38.05
3.07 38.07
38
38
0.05
0.07
3
3
0.4
4.09 38.09
38
0.09
0.5
4.12 38.12
38
0.12
0.6
5.14 38.14
38
0.14
0.7
5.16 38.16
38
0.16
0.8
6.19 38.19
38
0.19
0.9
6.21 38.21
38
0.21
1.0
1.1
8.2
8.3
38
38
0.2
0.3
3
3
38.2
38.3
Unit : mm
Order Number
DCSSSD0120
DCSSSD0130
DCSSSD0140
DCSSSD0150
DCSSSD0160
DCSSSD0170
DCSSSD0180
DCSSSD0190
DCSSSD0200
DC LCF OAL LF
PL DCON
1.2
1.3
8.3 38.3
8.3 38.3
38
38
0.3
0.3
3
3
1.4
8.3 38.3
38
0.3
1.5
10.3 45.3
45
0.3
1.6
10.3 45.3
45
0.3
1.7
10.4 45.4
45
0.4
1.8
10.4 45.4
45
0.4
1.9
2.0
10.4 45.4
12.4 45.4
45
45
0.4
0.4
3
3
DC
UWC
DCSSM
Medium, For non-ferrous material
P
Stock
Order Number
Stock
adhesion for coating layer and enables stable drilling without peeling
or chipping.
135
Thinning
2.1 < DC < 3
0
0.014
0
0.006
Non-ferrous Metal
h6
PL
DCON
DC
LF
LCF
OAL
a The original CVD diamond coating technology provides excellent
N254
Order Number
DC LCF OAL LF
PL DCON
DCSSMD0210
DCSSMD0220
DCSSMD0230
DCSSMD0240
DCSSMD0250
2.1 17.4 60.4 60

2.2 17.5 60.5 60
0.4
0.5
3
3
2.3 17.5 60.5 60
0.5
2.4 17.5 60.5 60

2.5 21.5 60.5 60
0.5
0.5
3
3
Unit : mm
Order Number
DC LCF OAL LF
PL DCON
Stock
Stock
DRILLING
adhesion for coating layer and enables stable drilling without peeling
or chipping.
DCSSMD0260
DCSSMD0270
DCSSMD0280
DCSSMD0290
DCSSMD0300
2.6 21.5 60.5 60
0.5
2.7 21.6 60.6 60
0.6
2.8 21.6 60.6 60
0.6
2.9 21.6 60.6 60

3.0 21.6 60.6 60
0.6
0.6
3
3
a
a
CARBIDE

Work
Material
Aluminium alloy
Copper
Copper alloy
Aluminium alloy
Graphite
Machineable Ceramics
MMC
FRP
Dia.
DC (mm)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
Revolution
(min-1)
Feed rate
(mm/rev)
0.2
0.5
1.0
1.5
2.0
2.5
3.0
20000
20000
20000
20000
20000
18500
17000
0.006
0.02
0.04
0.05
0.06
0.08
0.10
10000
10000
10000
10000
9000
7500
6000
0.003
0.01
0.02
0.02
0.03
0.04
0.05
20000
20000
20000
16000
11000
10000
8500
0.003
0.01
0.02
0.02
0.03
0.04
0.05
20000
20000
20000
16000
11000
10000
8500
0.01
0.03
0.05
0.08
0.10
0.12
0.15
10000
10000
10000
10000
9000
7500
6000
0.003
0.01
0.02
0.02
0.03
0.04
0.05
DRILLING
1) When drilling very hard work materials, reduce the feed.

2) Use water soluble coolant or grinding fluid when working.
3) When drilling deep holes, moderate the cutting conditions.
4) The revolution can be increased by using a high speed spindle.
N255
DCBSS
Drill for hard brittle materials
P
166
DC>0.07
0.05 < DC< 0.2 0.2 < DC < 3
0
0.009
0
0.006
Non-ferrous Metal
1.0
h6
LF
LF
Type2
6
OAL
PL
DC
DCON
DC
LCF
DCON
Type1
6
1.0
a For machining materials such as sintered ceramics and
LF
Type3
LCF
OAL
3
3
1
1
0.07 0.704 38.004 38
0.004
0.08 0.805 38.005 38
0.005
0.09 0.906 38.006 38
0.006
0.10 1.01 38.01
38
0.01
0.11 1.21 38.01
38
0.01
0.12 1.41 38.01
38
0.01
0.13 1.51 38.01
38
0.01
0.14 1.51 38.01
38
0.01
0.15 1.51 38.01
38
0.01
0.16 1.51 38.01
38
0.01
0.17 1.51 38.01
38
0.01
0.18 1.51 38.01
38
0.01
0.19 1.51 38.01
38
0.01
0.20 2.01 38.01
38
0.01
0.21 2.01 38.01
38
0.01
0.22 2.01 38.01
38
0.01
0.23 2.01 38.01
38
0.01
0.24 2.01 38.01
38
0.01
0.25 2.52 38.02
38
0.02
0.26 2.52 38.02
38
0.02
0.27 2.52 38.02
38
0.02
0.28 2.52 38.02
38
0.02
0.29 2.52 38.02
38
0.02
0.30 3.02 38.02
38
0.02
0.31 3.02 38.02
38
0.02
0.32 3.02 38.02
38
0.02
0.33 3.02 38.02
38
0.02
0.34 3.52 38.02
38
0.02
0.35 3.52 38.02

0.36 3.52 38.02
38
38
0.02
0.02
3
3
3
3
38
38
Order Number
DCBSSD0040
DCBSSD0045
DCBSSD0050
DCBSSD0055
DCBSSD0060
DCBSSD0070
DCBSSD0080
DCBSSD0085
DCBSSD0090
DCBSSD0100
DCBSSD0110
DCBSSD0120
DCBSSD0130
DCBSSD0140
DCBSSD0150
DCBSSD0160
DCBSSD0170
DCBSSD0180
DCBSSD0190
DCBSSD0200
DCBSSD0210
DCBSSD0220
DCBSSD0230
DCBSSD0240
DCBSSD0250
DCBSSD0260
DCBSSD0270
DCBSSD0280
DCBSSD0290
DCBSSD0300
DC LCF OAL LF
PL DCON
Type
Type
0.05 (0.5)
0.06 (0.6)
Unit : mm
Stock
PL DCON
Stock
DRILLING
DCBSSD0005
DCBSSD0006
DCBSSD0007
DCBSSD0008
DCBSSD0009
DCBSSD0010
DCBSSD0011
DCBSSD0012
DCBSSD0013
DCBSSD0014
DCBSSD0015
DCBSSD0016
DCBSSD0017
DCBSSD0018
DCBSSD0019
DCBSSD0020
DCBSSD0021
DCBSSD0022
DCBSSD0023
DCBSSD0024
DCBSSD0025
DCBSSD0026
DCBSSD0027
DCBSSD0028
DCBSSD0029
DCBSSD0030
DCBSSD0031
DCBSSD0032
DCBSSD0033
DCBSSD0034
DCBSSD0035
DCBSSD0036
Short
Delivery
quartz glass that cannot be machined with conventional

drills.
DC LCF OAL LF
0.40
0.45
4.02 38.02
4.03 38.03
38
38
0.02
0.03
3
3
a
r
3
3
0.50
4.03 38.03
38
0.03
0.55
4.53 38.03
38
0.03
0.60
5.04 38.04
38
0.04
0.70
5.04 38.04
38
0.04
0.80
6.05 38.05
38
0.05
0.85
6.05 38.05
38
0.05
0.90
6.06 38.06
38
0.06
1.00
8.1
38.1
38
0.1
1.10
8.1
38.1
38
0.1
1.20
8.1
38.1
38
0.1
1.30
8.1
38.1
38
0.1
1.40
8.1
38.1
38
0.1
1.50 10.1
38.1
38
0.1
1.60 10.1
38.1
38
0.1
1.70 10.1
38.1
38
0.1
1.80 10.1
38.1
38
0.1
1.90 10.1
38.1
38
0.1
2.00 12.1
38.1
38
0.1
2.10 12.1
38.1
38
0.1
2.20 12.1
38.1
38
0.1
2.30 12.1
38.1
38
0.1
2.40 12.2
38.2
38
0.2
2.50 12.2
38.2
38
0.2
2.60 12.2
38.2
38
0.2
2.70 12.2
38.2
38
0.2
2.80 12.2
38.2
38
0.2
2.90 12.2
3.00 12.2
38.2
38.2
38
38
0.2
0.2
3
3
3
3
(Note 1) Stock mark r (produced on order products) shows the basic sizes. Consult us, if different diameters and flute lengths.
(Note 2) Drills with e mark can be delivered within 1-2 weeks. For the delivery of other drills, contact Mitsubishi Materials.
(Note 3) DC=0.05, 0.06 are special shape specifications without groove. LCF is the neck lengths instead of the flute lengths.
N256
0
0.014
0
0.006
DCON
DC
LCF
PL
Order Number
DC
UWC
Short
Delivery
CARBIDE
CARBIDE

Aluminium nitride
Dia. Cutting speed Revolution

DC (mm)
(m/min)
(min-1)
0.05
0.08
0.1
0.16
0.2
0.32
0.4
0.5
0.6
0.8
1
1.2
1.6
2
3
3
5
6
9
9
12
15
19
19
25
31
30
40
38
47
Work
Material
20,000
20,000
20,000
18,000
15,000
12,000
12,000
12,000
10,000
10,000
10,000
8,000
8,000
6,000
5,000
Feed rate
(mm/rev)
Step
0.000015
0.00003
0.0002
0.0002
0.0002
0.0002
0.0002
0.0002
0.0002
0.0002
0.0002
0.00025
0.0003
0.0003
0.0003
0.001
0.003
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
(mm)
Cutting speed Revolution

(m/min)
(min-1)
3
5
6
9
9
12
15
19
19
25
31
30
40
38
47
Silicon carbide
Silicon nitride
Dia. Cutting speed Revolution

DC (mm)
(m/min)
(min-1)
0.05
0.08
0.1
0.16
0.2
0.32
0.4
0.5
0.6
0.8
1
1.2
1.6
2
3
Alumina
3
5
6
9
9
12
15
19
19
25
31
30
40
38
47
20,000
20,000
20,000
18,000
15,000
12,000
12,000
12,000
10,000
10,000
10,000
8,000
8,000
6,000
5,000
Feed rate
(mm/rev)
0.000005
0.00001
0.00005
0.00005
0.00005
0.00005
0.00005
0.00005
0.00005
0.00005
0.00005
0.00007
0.0001
0.0001
0.0001
20,000
20,000
20,000
18,000
15,000
12,000
12,000
12,000
10,000
10,000
10,000
8,000
8,000
6,000
5,000
Zirconia
Feed rate
(mm/rev)
Step
0.00001
0.00002
0.0001
0.0001
0.0001
0.0001
0.0001
0.0001
0.0001
0.0001
0.0001
0.00015
0.0002
0.0002
0.0003
0.001
0.002
0.005
0.005
0.005
0.005
0.005
0.005
0.005
0.005
0.005
0.005
0.005
0.005
0.005
(mm)

(m/min)
(min-1)
3
5
6
9
9
12
15
19
19
25
31
30
40
38
47
20,000
20,000
20,000
18,000
15,000
12,000
12,000
12,000
10,000
10,000
10,000
8,000
8,000
6,000
5,000
Feed rate
(mm/rev)
Step
0.00001
0.00002
0.0001
0.0001
0.0001
0.0001
0.0001
0.0001
0.0001
0.0001
0.0001
0.00015
0.0002
0.0002
0.0002
0.001
0.001
0.003
0.003
0.003
0.003
0.003
0.003
0.003
0.003
0.003
0.003
0.003
0.003
0.003
(mm)
Quartz glass
Step
(mm)
0.0005
0.001
0.002
0.002
0.002
0.002
0.002
0.002
0.002
0.002
0.002
0.002
0.002
0.002
0.002

(m/min)
(min-1)
3
5
6
9
9
12
15
19
19
25
31
30
40
38
47
20,000
20,000
20,000
18,000
15,000
12,000
12,000
12,000
10,000
10,000
10,000
8,000
8,000
6,000
5,000
Feed rate
(mm/rev)
Step
0.000015
0.00003
0.0002
0.0002
0.0002
0.0002
0.0003
0.0003
0.0003
0.0003
0.0003
0.0004
0.0004
0.0004
0.0005
0.001
0.005
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
(mm)
1) Depending on the type of machine, it is possible to apply cutting speeds over 20000min-1.
2) Use water soluble coolant or grinding fluid when working.
3) The intermediate diameter revolution is not tabulated. It is matched to the large diameter side and closest drill diameter conditions or by
calculating the cutting speed of the closest drill diameter. Set the feedrate per revolution to a suitable value with the recommended feedrate
of the closest drill diameter as the standard.
DRILLING
Work
Material
N257
Memo
N258
SPARE PARTS
IDENTIFICATION ................................................................. P002
SPARE PARTS
CLAMP SCREW ................................................................ P003
SET BOLT ......................................................................... P009
SHIM .................................................................................. P010
SHIM PIN AND CLAMP LEVER........................................ P013
LOCK PIN .......................................................................... P014
CLAMP BRIDGE ............................................................... P014
BREAKER PIECE ............................................................. P016
REPLACEMENT PARTS FOR OLD TYPE TOOLS
TURNING HOLDERS ..................................................... P017
BORING BARS ............................................................... P023
BORING UNITS .............................................................. P026
FACE MILLS ................................................................... P027
INDEXABLE TYPE END MILLS ..................................... P031
INDEXABLE TYPE DRILLS ........................................... P035
ANTI SEIZE LUBRICANT ................................................. P038
P001
SPARE PARTS
IDENTIFICATION
y IDENTIFICATION OF CLAMP SCREW (Metric coarse right screw thread)
H SC
060
05
a Hexagonal
Hole Dimensions
UNBRAKO CO.
Button
Head
FC
CHUUBURASHI CO.
Flat Head
Socket
Head
PM
Pan Head
FM
Flat Head
Set Screw
(Dog Point)
SS
Set Screw
(Flat Point)
SPARE PARTS
Long
L L Wrench
Symbol
Wrench
HKY Hexagonal Wrench

TKY Torx Wrench
TIP Torx plus Wrench
P002
Standard
15
20
25
30
35
40
50
60
B
1.5
2
2.5
3
3.5
4
5
6
Torx plus Wrench
Torx Wrench
Symbol
06
08
10
15
20
25
27
30
B
1.7
2.3
2.7
3.3
3.8
4.4
5.0
5.5
Size
Symbol
Size
T T Wrench
T6
T8
T10
T15
T20
T25
T27
T30
06
07
08
15
6IP
7IP
8IP
15IP
F
Flag
FS Wrench
Flag
W Wrench
D
Driver
DS
SR
Symbol
R L Wrench
Hexagonal Wrench
Set Screw
(Cone Point)
y IDENTIFICATION OF WRENCH
HKY 15
SP
S
With Cross Hole
Shape
Shape
Set Screw
(Cut Point)
JIS
Standard
SD
Symbol
HSo
0.9
1.3
1.5
2
2.5
3
4
5
Shape
SC
HSC
1.5
2
2.5
3
4
5
6
8
CHUUBURASHI CO.
H
Symbol
d
M5
M6
HFC
2
2.5
3
4
5
6
BH
BHA
Screw Head
With Slot
0.4
0.45
0.5
0.7
0.8
1
1.25
1.5
B Dimensions
HBH
2
2.5
3
4
5
6
Symbol
050
060
Hexagonal Hole
Dimensions
M2
M2.5
M3
M4
M5
M6
M8
M10
Example
Screw
Diameter
Symbol
Pitch
05
10
20
30
Diameter
Length
L
5
10
20
30
Example
Symbol
SPARE PARTS
CLAMP SCREW
Order Number
Geometry
Dimensions (mm)
a
Angle Drive Torque

' Size (Nm)
Tool Holder
AJS3010T10
AJS4012T15
AJS5014T25
5
7
8
M30.5 10
M40.7 12
M50.8 14
1.5
2.2
2.7
2.8 120 T10 2.5 Profile Holder

3.4 120 T15 3.5 AJX Type Cutter
4.5 120 T25 7.5
BRS103
BRS105
5
8
M30.5 9.9
M50.8 13.8
2.9
3.8
3.4 120 T15 3.5 BRE Type Cutter

4.5 120 T25 7.5
7
9
10.5
M40.7 14.6
M50.8 15.4
M61 22
2.6
3.4
4
2.5
3
4
2.2 F Type Boring Bar

3.3
7.0
This clamp screw is included with

the clamp as a set.
7.9
M50.8 19
4.5
10 T25 8.5 BF407 Type Cutter
CS200T
CS250T
CS250560T
CS300590T
CS300790TS
CS300890T
CS350760T
CS350790T
CS350860T
CS350990T
CS400990T
CS401160T
CS401990T
CS451190T
CS501160T
CS501290T
CS5015060T
CS502190T
CS6016060T
CSF401260T
3.2
3.7
3.9
4.1
4.7
4.1
5.5
4.8
5.5
4.8
6.0
5.7
6.0
6.3
7.0
7.0
7.2
8.5
8.5
7.2
M20.4
M2.50.45
M2.50.45
M30.5
M30.5
M30.5
M3.50.6
M3.50.6
M3.50.6
M3.50.6
M40.7
M40.7
M40.7
M4.50.75
M50.8
M50.8
M50.8
M50.8
M61.0
M40.5
5
6
5.2
5.5
7
8
7
7
8.4
9
9
11
19
11
11
11
15
21
16
12
1.6
1.8
2.5
2.1
2.3
2.1
4
2.4
4
2.4
2.8
4.5
3.0
2.9
3.6
3.5
2.4
4.0
4.5
5.2
1.8
2.4
2.4
2.4
2.8
2.4
3.4
2.8
3.4
2.8
3.4
3.4
3.9
3.9
3.9
4.5
3.9
5.1
4.5
3.9
90 T6
90 T8
60 T8
90 T8
90 T10
90 T8
60 T15
90 T10
60 T15
90 T10
90 T15
60 T15
90 T20
90 T20
60 T20
90 T25
60 T20
90 T27
60 T25
60 T20
M50.8 22.5
M61.0 25
2.5
4
3.4
3.9
T15 3.5 DOUBLE CLAMP Holder

T20 5.0 DOUBLE CLAMP DIMPLE BAR
CAS51T
e
*
*
d
c
*
d
AL Holder
F Type Boring Bar
MMTI Type Boring Bar
SNT Type Boring Bar
Milling Tools Series
AHX640S Type Cutter
Boring Unit
MI Type Boring Bar
PMR Type Cutter
0.6
1.0
1.0
1.0
2.0
1.0
3.5
2.5
3.5
2.5
3.5
3.5
3.5
5.0
5.0
7.5
5.0
7.5
7.5
5.0
8.5
10.5
DC0520T
DC0621T
HSK Tool Holder
SPARE PARTS
CS3(For Use with C3)

d
c
DKS4
DKS5
5.6
7.6
M40.7 18
M50.8 19
3.5
4.5
3
4
3.3
7.0
P003
SPARE PARTS
SPARE PARTS
CLAMP SCREW
Geometry
Order Number
EGS06019
EGS08024
Dimensions (mm)
a
9
11
Angle Drive Torque

' Size (Nm)
Tool Holder
M61 22.5
M81.25 28.5
3.5
4.5
3
4
3.3 EG Type Holder

7.0
M40.7
1.3
2.8
90 T10 2.5 AL Type Holder
FC400890T
5.6
7.5
SMG Type Holder
AL Type Boring Bar

d
8.7
M50.8 16
3.5
3.9
90 T20 5.0 GY Series
GY05016S
GY06013M
12
M61.0 18
5.6
T30 6.0 GY Series
HFF06015
10
M61 15
80
8.2
2.3
2.8
2.8
2.5
3
3
80
80
80
3.8
3.3
6.6
2.5
2.5 MP Type Holder
d
c
HS4L
HS5S
HS5L
5.4
6.8
6.8
M40.7 14
M50.8 9
M50.8 15
HSP05008C M50.8
D Type Boring Head

a
80
4.4
5.5
5.5
7
9.3
M30.5 7
M30.5 7
M30.5 10
M3.50.6 12
M50.8 16
2.1
2.5
2.5
2.9
3.6
2
2
2
2
3
82
82
82
82
82
JSS6
JSS7
6.9
8
M60.75 4.5
M70.75 4.4
1.5
1.5
0.8
1
5
7
6.5
5
7
3
4
4
5
3
4
4
5
2.5
3
3.3
7.0
7.0
9.0
HY-A1
HY-V1
HY2
HY3
HY4
SPARE PARTS
d
c
P004
1.5 Boring Unit

1.5
1.5
1.5
3.3
KS1
KS2
KS3
KS1S
KS2S
KS11
KS12
KS13
KS14
LLR1
LLR2
7
M40.7
10
M61
8
M40.7
7
M40.7
10
M61
8
M50.8
10
M61
10
M61
13
M81.25
M50.8
M61
14
18
14
14
18
19
26
30
45
3.5
5
V10000 Type Cutter

LL Type Cartridge
BC Type Cartridge
SS Type Cartridge
SET/MG/DG Type Cartridge
MI Type Boring Bar
LL Type Cartridge
Order Number
d LLCS103
*
e
d
c
d
c
LLCS103, LLCS105
LLCS125, LLCS205
The products with " " do not have a

hexagonal hole at the end marked b.
The products with "d" do not have a
hexagonal hole at the end marked a.
Left-Hand Screw
Right-Hand Screw
c
b
c
b
M30.5 4
M50.8 M50.8
M50.8 M50.8
M61
6
M61
6
M81.25 8
M81.25 8
M101.5 10
M121 11.9
M50.8 M50.8
M50.8 M50.8
M61
6
M81.25 8
M61
6
M81.25 8
M101 10
M101 10
M81
8
M81
8
M61 22
M81 29
M81 32
M61 15
M61 18
M81 24
M81 27
M60.75 18
M60.75 22
M70.75 16
M81 16
M81 24
M81 34
M70.75 24
M70.75 18
M70.75 23
M81 42
M70.75 14
M101.5 26
M101.5 32
M81.25 24
M81.0 28.5
M70.75 14
M70.75 24
M70.75 18
M60.75 11
M70.75 13
M60.75 22
M81.25 24
11
10
10
16.5
13.4
21
16.5
29
36.2
12
16
26
24
21
42
29
30
24
20.5
8
13
13
8
8
13
13
7
8
6
6
7
12
10
6
11
17
6
9
12
8.5
12.0
6
10
7
4
6
8
8.5
4.6
1.5
1.5
3.5
0.7
6.5
2
8
9
2
4
13
6.5
4
27.5
8
6.6
6.5
3
8
10
13
4
5
5
8
7
8
6
6
7
12
10
8
8
11
4
9
12
8.5
10.5
5
10
7
4
4
8
8.5
2
2
2
2.5
2.5
3
3
4
5
2
2
2.5
3
2.5
3
4
4
3
3
3
4
4
3
3
4
4
3
3
4
4
4
4
4
4
4
4
4
5
5
4
4
4.5
4.5
4.5
3.4
4.5
3.4
4
T25
T25
T25
T15
T25
T15
1.5
1.5
1.0
2.2
2.2
3.3
3.3
7.0
8.0
1.5
1.5
2.2
3.3
2.2
3.3
7.0
7.0
3.3
3.3
5.0
8.2
8.2
5.0
5.0
8.2
8.2
5.0
5.0
8.2
8.2
8.2
8.2
8.2
8.2
8.2
8.2
8.2
9.0
9.0
8.2
8.2
8.5
8.5
8.5
5.0
8.5
6.0
8.2
Tool Holder
LL Type Holder
P Type Boring Bar
P Type Boring Bar
D Type Boring Head
HSK Tool Holder
KSMG Type Cutter
LL Type Cartridge
Boring Unit
DOUBLE CLAMP Holder

(For Heavy Cutting)
MC Type Holder
UG Type Holder
APX3000 Type Cutter
Right-Hand
Screw
MGS6
10
M61 26
9.0
MHT1
11
M81 18.5
3.5 4
8.7
Left-Hand
Screw
Angle Drive Torque

' Size (Nm)
Right-Hand
Screw
Left-Hand
Screw
*Without Hexagonal Hole on Right-Hand Screw
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
LLCS105
LLCS105
LLCS106
LLCS106S
LLCS108
LLCS108S
LLCS110
LLCS112
LLCS125
LLCS205
LLCS206
LLCS208
LLCS306
LLCS308
LLCS310
LLCS410
LLCS508
LLCS508S
LS1
LS2
LS3
LS4
LS5
LS6
LS7
LS8
LS9
LS10
LS11
LS12
LS13
LS14
LS15
LS16
LS17
LS18
LS20
LS21
LS24
LS25
LS10T
LS14T
LS15T
LS19T
LS10TS
LS0622T
LS24H
Dimensions (mm)
SPARE PARTS
Geometry
P005
SPARE PARTS
SPARE PARTS
CLAMP SCREW
Order Number
Dimensions (mm)
Angle Drive Torque

' Size (Nm)
NS251
NS401
3.6
5.8
M2.50.45
M40.7
7
6
2.2
3.6
60
60
0.7 SMALL TOOLS

3.5
NS402W
NS403W
NS404W
5.85 M40.7 10
5.85 M40.7 12
5.8 M40.7 10
2.2
2.2
2.2
60
60
90
0.7 SMALL TOOLS

0.7
0.7
NS501W
NS502W
8
8
2.5 120
2.5 120
2.2 SMALL TOOLS

2.2
RN-S4S
RN-S4M
RN-S4
RN-S5
RN-S6
RN-S7
RS3008T
RS3510T
RS4015T
RS5020T
RS6025T
RS8030T
S1
S3
S4
S5
5.8
5.8
5.8
8.1
9.5
11
4.3
5
6
8.1
9.5
12
3.5
4.5
5.3
6.8
M40.5
M40.5
M40.5
M50.5
M60.75
M70.75
M30.35
M3.50.35
M40.5
M50.5
M60.75
M80.75
M20.4
M30.5
M40.7
M50.8
8.4
10
12.5
15.4
20.3
24.7
8.6
10
14
16.4
21.5
25
5.5
7.7
8
9
2.5
2.2
2.2
3.6
4.6
5.2
2
2.3
2.7
3.6
4.2
5
2.2
2.4
1.8
2.4
3.4
3.4
3.4
3.9
3.9
4.5
2.4
2.8
3.4
3.9
4.5
5.6
1.5
2
2.5
3
61 T15
61 T15
61 T15
61 T20
61 T20
61 T25
61 T8
61 T10
61 T15
61 T20
61 T25
61 T30
92
92
62
62
SD32
SD40
SD50
SD63
12
12
16
16
M81.25
M81.25
M101.5
M101.5
28
36
46
61
7.2
7.2
8.2
8.2
6
6
8
8
50
50
50
50
M50.8 14.8 1.5

M61 20
1.8
3.4
3.9
T15 3.5 MMTE Type Holder

T20 5.0 MMTI Type Boring Bar
M50.8 25
M61 32
6.3
6.2
4
4
90
90
M50.8 16
M50.8 20
SETS51
SETS61
6.8
8
3.5
3.5
3.5
5.0
5.0
7.5
1.5 SRF Type Cutter
2.5
3.3
5.0
7.5
10.0
1.0 Boring Unit
1.5
2.2
3.3
9.5 D Type Head Arbor
9.5
1.0
1.0
SET Type Holder

SNT Type Boring Bar
HSK Tool Holder
SET Type Cartridge
7.0 WP Type Holder

7.0 M Type Boring Bar
8.5
M50.8 16
4.5
70 T25 5.0
SRS5
6.7
M50.8 16
3.5
3.9
T20 5.0 SRE Type Cutter
STS1
6.8
M30.5 7
2.2
2.8
90 T10 2.5
c
b
a
e
SPS1
b
d
P006
10
12
SLCS105
SLCS106
SPARE PARTS
Tool Holder
Geometry
Order Number
TS16
TS2
TS2A
TS2C
d TS2D
TS21
TS22
TS25
d TS25D
TS25H
TS202
TS253
TS254
TS255
TS3
TS3D
TS3SB
TS31D
TS32
TS33
TS35
TS35D
TS351
TS352
TS4S
TS4SL
TS4SB
TS4SBL
TS4
TS4D
TS42
TS43
TS44
TS406
TS407
TS450
TS5S
TS5SL
TS5
TS5L
TS52
TS53
TS54
TS55
TS6S
TS6
TPS20
TPS22
TPS22S
TPS25
TPS25-1
TPS3
TPS35
TPS351
TPS4
TPS43
TPS4R
TPS54
*
*
*
*
*
*
*
*
b
*
e
*
*
*
d
c
d
c
*
*
Dimensions (mm)
a
2.5
2.7
2.7
2.7
3.8
2.7
3.0
3.3
4.4
3.6
2.7
3.3
3.3
3.5
3.9
5.0
4.4
4.8
3.9
3.9
4.8
5.3
4.8
4.8
5.4
5.4
5.8
5.8
5.4
5.6
5.4
5.4
5.4
5.4
5.4
5.9
6.8
6.8
6.8
6.8
6.8
6.8
6.8
6.8
8.5
8.5
2.7
3.0
3.0
3.3
3.3
3.9
5.3
4.8
5.3
5.3
6.4
6.8
M1.60.35
M20.4
M20.4
M20.4
M20.4
M20.4
M2.20.45
M2.50.45
M2.50.45
M2.50.45
M20.4
M2.50.45
M2.50.45
M2.50.45
M30.5
M30.5
M30.5
M30.5
M30.5
M30.5
M3.50.6
M3.50.6
M3.50.6
M3.50.6
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M40.7
M4.50.75
M50.8
M50.8
M50.8
M50.8
M50.8
M50.8
M50.8
M50.8
M61.0
M61.0
M20.4
M2.20.45
M2.20.45
M2.50.45
M2.50.45
M30.5
M3.50.6
M3.50.6
M40.7
M40.7
M40.7
M50.8
3.2
4.6
4.5
3.8
5.3
3.4
5
5.5
6.2
5.5
5.5
4.5
7
7.5
6
6
8
7.2
7.5
6.7
6.5
12
7.2
10
7
8
9
10.5
8
7.7
6
10
12
15.5
9
13
9
12
9
15
8
16
12
10.5
13
16
3.5
4.7
4.2
5.5
6.5
6.7
11.5
7.2
8
10
10.6
12
1.6
1.4
1.2
1.4
1.9
1.4
1.2
1.7
2.2
2
1.8
1.7
1.7
1.6
2
2.3
2
2.2
2
2
2.4
2.8
2.4
3
2.4
2.4
2.7
2.7
2.6
2.5
2.6
2.6
2.6
2.6
2.6
3.6
2.9
2.9
3.2
2.9
3.2
3.2
3.2
3.2
4.4
4.4
1.3
1.6
1.6
1.7
1.7
1.4
2.8
1.4
2.6
2.6
2.9
3.2
1.8
1.8
1.8
1.8
1.8
1.8
1.8
2.4
2.4
2.4
1.8
2.4
2.4
2.4
2.4
2.8
2.4
2.8
2.4
2.4
2.8
3.4
2.8
2.8
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.9
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
5.6
5.6
1.8
2.1
2.1
2.1
2.1
2.82
3.4
2.82
3.4
3.4
3.4
4.5
Angle Drive Torque

' Size (Nm)
60
60
60
60
82
60
60
60
82
60
60
60
60
60
60
82
80
82
60
60
60
60
60
60
80
80
80
80
60
82
60
60
60
60
60
60
80
80
60
80
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
T6 0.6
T6 0.6
T6 0.6
T6 0.6
T6 0.6
T6 0.6
T6 0.6
T8 1.0
T8 1.0
T8 1.0
T6 0.6
T8 1.0
T8 1.0
T8 1.0
T8 1.0
T10 2.5
T8 1.5
T10 2.5
T8 1.0
T8 1.0
T10 2.5
T15 3.5
T10 2.5
T10 2.5
T15 3.5
T15 4.0
T15 3.5
T15 3.5
T15 3.5
T15 3.5
T15 3.5
T15 3.5
T15 3.5
T15 3.5
T15 3.5
T20 5.0
T25 7.5
T25 7.5
T25 7.5
T25 7.5
T25 7.5
T25 7.5
T25 7.5
T25 7.5
T30 10.0
T30 10.0
6IP 0.6
7IP 0.6
7IP 0.6
7IP 1.0
7IP 1.0
IP10 1.0
15IP 3.5
IP10 2.5
15IP 3.5
15IP 3.5
15IP 3.5
P25 3.5
Tool Holder
SP Type Holder
Profile Holder
SMALL TOOLS
DIMPLE BAR
MICRO-DEX
F Type Boring Bar
S Type Boring Bar
GY SERIES
MMTI Type Boring Bar
SNT Type Boring Bar
HSK Tool Holder
VFX5 Type Cutter
VFX6 Type Cutter
SS Type Cartridge
Boring Unit
TAF Drill
ASX445 Type Cutter
SPARE PARTS
Geometry
ASX400 Type Cutter

APX3000 Type Cutter
APX4000 Type Cutter MVX Drill
ARX Type Cutter
MVX Drill
PMR Type Cutter
MVX Drill
MVX Drill
WSX445
MVX Large diameter
P007
SPARE PARTS
SPARE PARTS
Order Number
TSR05008S
TSR06011S
Geometry
CLAMP SCREW
Dimensions (mm)
c
Angle Drive Torque

' Size (Nm)
3.5
4
M50.8 8
M61.0 11
2.8
3.9
T10
T20
M40.7 5
M50.8 6
M61 10
2.4
2.8
3.9
T8
T10
T20
6.3
7.8
M50.5 7
M60.75 10
3.3
4.1
3.5
4.0
Tool Holder
TSS04005
TSS05006
TSS06010
PMF Type Cutter

BC Type Cartridge
SS Type Cartridge
WCS503507H
WCS604010H
5.0 ASX445 Type Cutter

7.0 ASX400 Type Cutter
PMR Type Cutter
WS1
8.5
M50.8 19
4.5
T25 7.5
WS254012T
WS254013T
WS254014T
WS254015T
WS254016T
WS304517T
WS304518T
WS355520T
WS355521T
WS406023T
WS406024T
WS508026T
WS508027T
4
4
4
4
4
4.5
4.5
5.5
5.5
6
6
8
8
M2.50.45
M2.50.45
M2.50.45
M2.50.45
M2.50.45
M30.5
M30.5
M3.50.6
M3.50.6
M40.7
M40.7
M50.8
M50.8
2.2
2.2
2.2
2.2
2.2
3.4
3.4
3.9
3.9
4.4
4.4
5.2
5.2
2.4
2.4
2.4
2.4
2.4
2.8
2.8
3.4
3.4
4.5
4.5
5.1
5.1
80
80
80
80
80
60
60
60
60
60
60
60
60
SPARE PARTS
P008
11.5
12.5
13.5
14.5
15.5
16.5
17.5
19.5
20.5
22.0
23.0
25.0
26.0
T8 2.0 TAW Drill

T8 2.0
T8 2.0
T8 2.0
T8 2.0
T10 3.5
T10 3.5
T15 5.5
T15 5.5
T25 8.5
T25 8.5
T27 12.0
T27 12.0
SET BOLT
Order Number
Dimensions (mm)
a
Angle Drive Torque

' Size (Nm)
BOES101
15
M101.5 45
10
HSC08030H
HSC08040
HSC08050
HSC10030H
HSC10035
HSC10045
HSC10055
HSC12035
HSC12035H
HSC12045
HSC12070
HSC16040
HSC16040H
HSC16080
HSC20040
HSC20090
HFF08043H
13
13
13
16
16
16
16
18
18
18
18
24
24
24
30
30
11
M81.25
M81.25
M81.25
M101.5
M101.5
M101.5
M101.5
M121.75
M121.75
M121.75
M121.75
M162
M162
M162
M202.5
M202.5
M81.25
8
8
8
10
10
10
10
12
12
12
12
16
16
16
20
20
5
5
5
5
6
6
6
6
10
10
10
10
14
14
14
17
17
5
Tool Holder
60 10.0 OCTACUT Type Cutter
Geometry
38
48
58
40
45
55
65
47
47
57
82
56
56
96
60
110
43
90
24
24
24
40
40
40
40
80
80
80
80
150
150
150
320
320
8.2
APX3000/4000 Type Cutter AJX Type Cutter

APX4000 Type Cutter WSX445 Type Cutter
AXD4000 Type Cutter
AXD7000 Type Cutter
APX3000/4000 Type Cutter AJX Type Cutter WSX445 Type Cutter
BXD Type Cutter
VFX5/6 Type Cutter
WSX445 Type Cutter

APX3000/4000 Type Cutter AJX Type Cutter WSX445 Type Cutter
WSX445 Type Cutter
APX3000/4000 Type Cutter AJX Type Cutter
AXD4000 Type Cutter
MBA16033H
MBA20040H
MBA24045H
M162 43
M202.5 54
M243 59
10
14
14
14
17
17
150 AHX640 Type Cutter (For & 100) WSX445 Type Cutter
APX4000 Type Cutter
320 AXD4000 Type Cutter
520 AXD7000 Type Cutter
AJX Type Cutter
BXD Type Cutter
HDS08030
HDS10031
Dimensions (mm)
a
M80.75 M81.25 30
M101.0 M101.5 31
Torque
Tool Holder
(Nm)
13.5
14
11.5
12
4
5
8.2 BRP Type Cutter

9.0 OCTACUT Type Cutter
PMF Type Cutter
Right-Hand
Screw
Order Number
Right-Hand
Screw
Geometry
40
50
65
c
b
SPARE PARTS
BXD Type Cutter
P009
SPARE PARTS
SPARE PARTS
SHIM
Geometry
*
a
Order Number
*
e
35
*
*
*
*
*
*
CS32
CS42
CS43
CS62
PS31
PS42
PS62
CT22
CT32
CT33
CT42
PT21
PT32
PT42
BPT322
DCSVN32
Dimensions (mm)
a
9.52
12.70
12.70
19.05
8.28
11.46
17.20
6.35
9.52
9.52
12.70
5.11
8.28
10.85
7.8
9.52
3.18
3.18
4.76
3.18
2.38
3.18
3.18
3.18
3.18
4.76
3.18
2.38
3.18
3.18
3.18
3.18
0.8
0.8
0.8
1.2
0.2
0.2
0.3
0.4
0.4
0.4
0.4
0.2
0.2
0.3
0.8
0.8
0.8
0.8
1.2
0.2
0.2
0.3
0.8
0.8
0.8
0.8
0.2
0.2
0.3
1.2
1.2
1.2
1.2
1.6
0.6
0.6
0.7
1.2
1.2
1.2
1.2
0.6
0.6
0.7
1.2
1.6
1.6
1.6
0.6
1.0
0.7
Tool Holder
MC Type Holder (Negative type)
MC Type Holder (Positive type)

BC Type Cartridge
MC Type Holder (Negative type)
MC Type Holder (Positive type)

F Type Boring Bar
BC Type Cartridge
DOUBLE CLAMP Holder
DOUBLE CLAMP DIMPLE BAR
da
b
d
ESS42
12.70
3.18
0.8
0.8
1.2
1.6
ML Type Holder
EST32
EST43
9.52
12.70
3.18
4.76
0.4
0.4
0.8
0.8
1.2
1.2
ML Type Holder
LLSCN3T3
LLSCN33
LLSCN42
LLSCN53
LLSCN63
LLSCP42
LLSCP63
9.52
9.52
12.70
15.87
19.05
12.70
19.05
3.97
4.76
3.18
4.76
4.76
3.18
4.76
0.4
0.4
0.8
1.2
1.2
0.8
1.2
0.4
0.4
0.8
1.2
1.2
0.8
1.2
0.8
0.8
1.2
1.6
1.6
1.2
1.6
0.8
0.8
1.2
1.6
1.6
1.2
1.6
LLSDN32
LLSDN42
LLSDN43
LLSDN53
LLSDP42
LLSRN103
LLSRN123
LLSRN164
LLSRN204
LLSRN256
LLSRN326
LLSSN32
LLSSN33
LLSSN42
LLSSN53
LLSSN63
LLSSN84
LLSSP42
9.52
12.70
12.70
15.87
12.70
8.3
9.8
13.6
17.3
22.0
28.0
9.52
9.52
12.70
15.87
19.05
25.40
12.70
3.18
3.18
4.76
4.76
3.18
3.18
3.18
4.76
4.76
6.35
6.35
3.18
4.76
3.18
4.76
4.76
6.35
3.18
0.8
0.8
0.8
1.2
0.8
0.8
0.8
0.8
1.2
1.2
1.6
0.8
1.2
1.2
1.2
1.6
1.2
0.8
0.8
0.8
1.2
1.2
1.6
0.8
1.2
1.2
1.2
1.6
1.6
2.4
1.2
1.2
1.2
1.6
1.6
2.0
2.4
1.6
*
*
*
SPARE PARTS
ad
*
a
P010
DOUBLE CLAMP Holder

LL Type Holder
P Type Boring Bar
D Type Boring Head
HSK Tool Holder
LL Type Cartridge
P Type Boring Bar
HSK Tool Holder
DOUBLE CLAMP Holder
LL Type Holder

P Type Boring Bar
D Type Boring Head
HSK Tool Holder

LL Type Holder
HSK Tool Holder
LL Type Holder
P Type Boring Bar
LL Type Cartridge
Geometry
Order Number
*
e
d
e
55
b
c
ad
Tool Holder
LLSTE32
LLSTN32
LLSTN33
LLSTN42
LLSTN53
LLSTP32
LLSTP42
LLSWN32
LLSWN3T3
LLSWN42
LLSWP32
LLSWP42
MHS532R/L
MHS533R/L
MHS534R/L
MHS542R/L
MHS543R/L
MHS544R/L
MLCP42
7.6
9.52
9.52
12.70
15.87
9.52
12.70
9.52
9.52
12.70
9.52
12.70
9.4
9.4
9.4
9.4
9.4
9.4
12.58
3.18
3.18
4.76
3.18
4.76
3.18
3.18
3.18
3.97
3.18
3.18
3.18
15.7
15.7
15.7
15.7
15.7
15.7
3.18
0.4
0.4
0.4
0.4
0.8
0.4
0.4
0.4
0.4
0.4
0.4
0.4
4.5
4.5
4.5
6.5
6.5
6.5
1.2
0.4
0.8
0.8
0.8
1.2
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.2
1.6
0.8
1.2
1.6
1.2
0.4
1.2
1.2
1.2
1.6
1.2
1.2
1.2
1.2
1.2
1.2
1.2
0.8
1.2
1.6
0.8
1.2
1.6
1.2
1.2
MLDP42
12.56
3.18
1.2
1.2
P Type Boring Bar
MLSP42
12.63
3.18
1.2
1.2
1.2
1.2
P Type Boring Bar
MLTP32
9.50
3.18
1.2
1.2
1.2
P Type Boring Bar
LL Type Holder
DOUBLE CLAMP Holder
P Type Boring Bar
D Type Boring Head
LL Type Cartridge
Boring Unit
LL Type Holder
DOUBLE CLAMP Holder
P Type Boring Bar
b
d
*
*
*
*
Dimensions (mm)
d
a
a
c
18.8
4.76
1.6
1.6
1.6
1.6
DOUBLE CLAMP Holder

(For Heavy Cutting)
MSSN63
18.8
4.76
1.6
1.6
1.6
1.6
DOUBLE CLAMP Holder

(For Heavy Cutting)
MSCN63
CT32T1
SPARE PARTS
PT32T1R
PT32T2R
PT42TR
9.525
8.28
8.28
10.85
15.03
3.18
13.34
13.19
17.20
3.18
3.18
3.18
SET Type Holder

SNT Type Boring Bar
SET Type Cartridge
P011
SPARE PARTS
SPARE PARTS
SHIM
Geometry
35
Order Number
da
Dimensions (mm)
Tool Holder
PV321
PV322
PV323
9.52
9.52
9.52
3.18
3.18
3.18
0.4
0.8
1.2
0.4
0.8
1.2
MP Type Holder
SPSVN32
8.06
3.18
0.3
0.3
SP Type Holder
D Type Boring Head
b
c
HSK Tool Holder
d a
SPARE PARTS
P012
0.4
0.4
0.4
ASX400 Type Cutter
STASX445N
10.76
3.00
ASX445 Type Cutter
STBS500N
12.7
3.18
0.8
0.8
0.8
0.8
WPSTN33
WPSTN43
9.3
12.50
4.76
4.76
0.8
0.8
0.4
0.4
1.2
1.2
WP Type Holder
* * WPSWC43
WPSWN43
12.50
12.50
4.76
4.76
0.4
0.4
0.8
0.8
1.2
1.2
M Type Boring Bar
e
c
0.4
f
c
3.00
11.00
STASX400N
SHIM PIN AND CLAMP LEVER

Order Number
Geometry
Dimensions (mm)
a
Tool Holder
BCP141
BCP201
BCP202
BCP251
BCP252
BCP301
BCP401
CCP33
CCP34
CCP44
3.0
4.3
4.3
4.8
4.8
5.3
6.3
6.5
7.5
7.5
1.4
2
2
2.5
2.5
3
4
3.66
5.0
5.0
5.6
7.4
6.4
7.4
6.4
7.4
7.4
M50.8
M61.0
M50.8
18.5
18.5
14.2
3
3
3
MC Type Holder
LLCL12S
LLCL13
LLCL13S
LLCL14
LLCL14S
LLCL15
LLCL16
LLCL18
LLCL23
LLCL23S
LLCL24
LLCL25
LLCL110
LLCL112
LLCL116
LLCL120
LLCL125
LLCL132
LLP13
LLP14
LLP15
LLP16
LLP18
LLP23
LLP24
2.1
3.6
3.6
4.7
4.7
6.0
7.5
8.6
3.6
3.6
4.7
6.0
3.0
3.5
4.5
5.6
6
8
5.55
7.25
8.8
10.85
15.35
5.55
7.25
9.3
10
10
13.4
13.6
19
20.8
25.4
12.0
11.6
16.2
17.1
10.7
13
18.5
20.3
24
30
4.85
6.55
8.05
9.85
13.05
4.85
6.55
5.6
12.5
7.8
13.2
12.2
17
21
25.2
11.5
9.5
14.8
17
11.6
13.5
18
19
24
27
5.3
5.8
8.6
11.1
12.0
6.8
9.1
LL Type Holder
SP Type Holder
F Type Boring Bar
HSK Tool Holder
BC Type Cartridge
WP Holder
M Type Boring Bar
P Type Boring Bar

D Type Boring Head
HSK Tool Holder
KSMG Type Cutter
LL Type Cartridge
Boring Unit
LL Type Holder
DOUBLE CLAMP Holder
P Type Boring Bar
D Type Boring Head
HSK Tool Holder
KSMG Type Cutter
LL Type Cartridge
MP6
e
d
11.9
7.8
M101
22.1
15
DOUBLE CLAMP Holder

(For Heavy Cutting)
SPARE PARTS
Boring Unit
P013
SPARE PARTS
SPARE PARTS
LOCK PIN
Order Number
Geometry
Dimensions (mm)
Tool Holder
P11S
P21S
6
7.5
3.7
4.9
4
4.5
17
17.2
11.1
11.5
MP Type Holder
P221US
P321US
P322US
P323US
P332US
P323WS
P333WS
P334WS
P433W
P434W
4
5.5
18
18
2.11
3.64
3.5
5.0
3.3
3.3
7.7
7.5
ML Type Holder
5.5
21
3.64
5.0
3.3
10.5
5.5
5.5
24
21
3.64
3.64
5.0
5.0
3.3
4.9
13.5
8.9
5.75
5.75
24
24
3.64
3.64
5.0
5.0
3.3
4.9
12.9
11.3
5.75
30
3.64
5.0
4.9
17.3
7.75
7.75
24
30
5.03
5.03
7.0
7.0
4.9
4.9
10.8
16.8
D Type Boring Head
e
d
e
b
e
b
ML Type Holder
CLAMP BRIDGE
Geometry
Order Number
Dimensions (mm)
Tool Holder
AMS3
AMS4
AMS5
7
9
10
12
13.5
15
3
3
3.5
3.3
3.8
5
CA142
CA150
CA151
CA152
CA153
CA161
CA162
CA163
CA181
CA183
CCK13
CCK14
8
9
15
16
4
4.5
7
7
10
17
10
19
10
24
13
20
13
24
13
27
16
16
30
37
8
8
10
10
15
19
18.5
22
6
8
9
9.5
CCTC1
13
25
10.2
CK231
CK232
CK341
CK342
M61
M61
8
8
4
4.5
7.5
8
4.5
4.5
9.5 MC Type Holder

11.5
M81
11
5.5
13.5
13.5
M81
11
14
16.5
Profile Holder
AJX Type Cutter
BRE Type Cutter
WP Type Holder
M Type Boring Bar
SPARE PARTS
a
f
e
P014
Left-hand
screw
CLAMP BRIDGE
Geometry
Order Number
Left-hand
screw
Dimensions (mm)
a
CKW6
10.9
22.5
DCK2211
DCK2613
DCK3113
11
13
13
KGC1
Tool Holder
9.2
16.8
22
26.5
31
6.57
7.35
9
11.1
12.9
14.5
DOUBLE CLAMP Holder
12.0
15.0
M70.75
UG Type Holder
14.3
4.5
5.9
MHK5NR/L
15.5
23.5
8.1
12.1
MTK1R/L
13
17.5
12
MTK2R/L
18
28
14
M81 DOUBLE CLAMP Holder

(For Heavy Cutting)
c
d

HSK Tool Holder
a
a
LK1
c
d
MG Type Holder
MT Type Holder
MT1 Type Holder
HSK Tool Holder
MG Type Cartridge
a
a
SETK51
SETK61
6.8
8.9
14.5
18.1
2.9
4.1
8
8.6
MMTE Type Holder

MMTI Type Holder
SET Type Holder
SNT Type Holder
HSK Tool Holder
SET Type Cartridge
SRK1R
9.4
21
5.5
7.5
SRE Type Cutter
24
c
a
SPARE PARTS
UCR
12
P015
SPARE PARTS
SPARE PARTS
BREAKER PIECE
Order Number
Geometry
60
SPARE PARTS
Inscribed Circle Breaker Width
CBS3
9.4
CBS4
12.6
9.2
2.5
12.70
3.5
CBS4N
12.6
10.2
2.5
12.70
2.5
CBS4F
12.6
11.2
2.5
12.70
1.5
CBS6
18.9
14.6
2.5
19.05
4.5
CBS6N
18.9
16.6
2.5
19.05
2.5
CBS6F
18.9
17.6
2.5
19.05
1.5
CBS3D
8.0
1.5
CBS4D
10.2
2.5
12.70
2.5
CBS6D
15.6
2.5
19.05
3.5
8.0
1.5
9.525
9.525
1.5
1.5
CBT2
5.33
1.4
1.5
6.35
1.5
CBT2N
5.67
1.4
1.5
6.35
1.0
CBT3
7.20
1.4
2.5
9.525
3.5
CBT3N
7.87
1.4
2.5
9.525
2.5
CBT3F
8.53
1.4
2.5
9.525
1.5
CBT4
9.73
1.4
2.5
12.70
4.5
CBT4N
11.07
1.4
2.5
12.70
2.5
CBT4F
11.73
1.4
2.5
12.70
1.5
Order Number
Geometry
P016
Tool Holder
MC Type Holder
MC Type Holder
Dimensions (mm)
Dimensions (mm)
Thread Pitch (mm)
CBT3106
11.5
10.6
2.0
2.5 3.0
CBT3113
11.5
11.3
2.0
1.5 2.0
CBT3120
11.5
12
2.0
0.75 1.25
CBT4108
13.3
10.8
2.0
3.5 4.0
CBT4128
13.3
12.8
2.0
4.5 5.0
MC Type Holder
F Type Boring Bar
positive inserts, the breaker

*For
width is 0.5mm larger than the
figures in the list.
Tool Holder
SPARE PARTS

(TURNING HOLDERS)
LL TYPE HOLDER
Old Type Tool Number
Type
PCFNR/L
PCLNR/L
PCBNR/L
PTANR/L
PTBNR/L
PTTNR/L
PTGNR/L
PTFNR/L
PSBNR/L
PSSNR/L
PSKNR/L
PRGCR/L
PRDCN
Size
1616H09
2020K09
2525M09
2020K12
2525M12
2525M16
3225P16
4040R19
1010E11
1212F11
1616H16
2020K16
2525M16
2525M22
3225P22
3232P22
4040R27
3225P12
2525M15
3232P15
3232P19
4040R19
5050T25
2020K10
2020K12
3225P12
3225P16
4040R25
5050T32
Shim
Shim Pin
LLSCN3T3
LLSCN3T3
LLP13
LLP13
Clamp Lever
LLCL13
LLCL13
Clamp Screw
Wrench
LLCS106
LLCS106
HKY25R
HKY25R
LLSCN3T3
LLP13
LLCL13
LLCS106
HKY25R
LLSCN42
LLP14
LLCL14
LLCS108
HKY30R
LLSCN42
LLP14
LLCL14
LLCS108
HKY30R
LLSCN53
LLP15
LLCL25
LLCS508
HKY30R
LLSCN53
LLSCN63
LLP15
LLP16
LLCL25
LLCL16
LLCS508
LLCS310
HKY30R
HKY40R
LLCL12S
LLCL12S
LLCS105
LLCS105
HKY20F
HKY20F
LLSTN32
LLP13
LLCL13
LLCS106
HKY25R
LLSTN32
LLP13
LLCL13
LLCS106
HKY25R
LLSTN32
LLP13
LLCL13
LLCS206
HKY25R
LLSTN42
LLP14
LLCL14
LLCS108
HKY30R
LLSTN42
LLP14
LLCL14
LLCS108
HKY30R
LLSTN42
LLSTN53
LLP14
LLP15
LLCL14
LLCL25
LLCS108
LLCS508
HKY30R
HKY30R
LLSSN42
LLSSN53
LLP14
LLP15
LLCL14
LLCL25
LLCS108
LLCS508
HKY30R
HKY30R
LLSSN53
LLP15
LLCL25
LLCS508
HKY30R
LLSSN63
LLP16
LLCL16
LLCS310
HKY40R
LLSSN63
LLSSN84
LLP16
LLP18
LLCL16
LLCL18
LLCS310
LLCS112
HKY40R
HKY50R
LLSRN103
LLSRN123
LLP13
LLP13
LLCL110
LLCL112
LLCS205
LLCS106
HKY20R
HKY25R
LLSRN123
LLP13
LLCL112
LLCS106
HKY25R
LLSRN164
LLP24
LLCL116
LLCS306
HKY25R
LLSRN256
LLSRN326
LLP16
LLP18
LLCL125
LLCL132
LLCS410
LLCS112
HKY40R
HKY50R
MC TYPE HOLDER (OLD TYPE PRODUCTS)

Size
N11R/L
N12R/L
N13R/L
N14M
N15R/L
22
33H
44
22
33H
44
22
33
44
22
33
44
N21R/L
N22R/L
N25R/L
P11R/L
P12R/L
P14M
P15R/L
P21R/L
P22R/L
P25R/L
Shim
Shim Pin
Clamp Bridge
CS32
CS42
CS42
BCP251
BCP301
BCP301
CK6
CK2
CK2
LS1
LS2
LS3
CBS3p
CBS4p
CBS4p
HKY30R
HKY40R
HKY40R
CT22
CT32
CT32
BCP201
BCP301
BCP301
CK1
CK2
CK2
LS1
LS2
LS3
CBT2p
CBT3p
CBT3p
HKY30R
HKY40R
HKY40R
PS31
PS42
PS42
BCP201
BCP251
BCP251
CK6
CK3
CK3
LS1
LS2
LS3
CBS3p
CBS4p
CBS4p
HKY30R
HKY40R
HKY40R
PT21
CT32
CT32
BCP141
BCP201
BCP201
CK1
CK2
CK2
LS1
LS2
LS3
CBT2p
CBT3p
CBT3p
HKY30R
HKY40R
HKY40R
*
*
*
*
Clamp Screw Breaker Piece
Wrench
SPARE PARTS

Type
*Please use clamp bridge No.CK3 with N11R/L33H and N11R/L44 types. Please use clamp bridge No.CK2 with P12R/L33 and P12R/L44 types.
P017
SPARE PARTS

(TURNING HOLDERS)
MC TYPE HOLDER
Type
CTANR/L
CTGNR/L
CSTNR/L
CSSNR/L
CTAPR/L
CSBPR/L
CSSPR/L
CSKPR/L
CTCPR/L
Size
1616
2020
2525
1616
2020
2525M43
2020
1616
2020
2020K16
2525M16
Shim
Shim Pin
Clamp Bridge Clamp Screw Breaker Piece
Wrench
Spring
CT22
CT32
CT32
BCP201
BCP301
BCP301
CK231
CK341
CK341
LS1
LS2
LS3
CBT2p
CBT3p
CBT3p
HKY30R
HKY40R
HKY40R
CS32
CS42
CS42
BCP251
BCP301
BCP301
CK232
CK341
CK341
LS1
LS2
LS3
CBS3p
CBS4p
CBS4p
HKY30R
HKY40R
HKY40R
PT32
BCP201
CK341
LS2
CBT3p
HKY40R
PS31
PS42
BCP201
BCP251
CK232
CK342
LS1
LS2
CBS3p
CBS4p
HKY30R
HKY40R
BPT322
BPT322
BCP201
BCP201
CCTC1
CCTC1
HSC06020
HSC06020
CBT3p
CBT3p
HKY50R
HKY50R
MES3
MES3
ML TYPE HOLDER (OLD TYPE PRODUCTS)

Type
Size
E11R/L
E12R/L
E13R/L
E14R/L
E15R/L
11U
22U
33W
44W
11U
22FU
33HU
33FW
33HW
44AW
44BW
E21R/L
E22R/L
E25R/L
E26M
E27R/L
Lock Pin
Shim
Stop Ring
Spanner
P321US
P322US
ER3
ER3
KY40
KY40
P433W
P434W
ESS42
ESS42
ER4
ER4
KY40
KY40
P221US
P322US
ER2
ER3
KY25
KY40
P333US
ER3
KY40
P323WS
EST32
ER3
KY40
P333WS
EST32
ER3
KY40
P334WS
P434W
EST32
EST43
ER3
ER4
KY40
KY40
Lock Pin
Shim
Stop Ring
Spanner
P221US
P322US
ER2
ER3
KY25
KY40
P332US
ER3
KY40
P323WS
EST32
ER3
KY40
P333WS
EST32
ER3
KY40
P334WS
P434W
EST32
EST43
ER3
ER4
KY40
KY40
P321US
P322US
ER3
ER3
KY40
KY40
P433W
P434W
ESS42
ESS42
ER4
ER4
KY40
KY40
ML TYPE HOLDER
SPARE PARTS
Type
ETANR/L
ETENN
ETFNR/L
ETXNR/L
ESBNR/L
ESENR/L
ESDNR/L
ESKNR/L
Size
1212
1616H32
1616H33
2020K32W
2020K33W
2525M33W
2525M43W
1212
1616H32
2020W
2525W
MH TYPE HOLDER
P018
Type
Size
KKCR/L
445
Shim
Shim Pin
Clamp Bridge
Clamp Screw
Stop Ring
Wrench
MHS532R/L
533R/L
534R/L
SFC03010
MHK5NR/L
MHT1
CE8
HKY40R
SL TYPE HOLDER
Type
ETJNR/L
ETQNR/L
ETNNR/L
Shim
Lock Pin
Nut
33K16S
SLSTN33
SLP13
SLN13
SLCW13
SLCS105
44M16S
SLSTN33
SLP13
SLN13
SLCW13
SLCS105
44M22S
SLSTN43
SLP14
SLN14
SLCW14
SLCS106
54P22S
SLSTN43
SLP14
SLN14
SLCW14
SLCS106
64M22S
SLSTN43
SLP14
SLN14
SLCW14
SLCS106
85M22S
SLSTN43
SLP14
SLN14
SLCW14
SLCS106
Size
Clamp Wedge Clamp Screw
Wrench
HKY25R
HKY40R
HKY25R
HKY40R
HKY30R
HKY40R
HKY30R
HKY40R
HKY30R
HKY40R
HKY30R
HKY40R
WP TYPE HOLDER (OLD TYPE PRODUCTS)

Type
Size
Shim
Shim Pin
Clamp
Bridge
Clamp
Screw
Side Lock
Plate
Lock
Screw
Spring
Wrench
HKY25R
HKY40R
HKY25R
HKY40R
HKY30R
HKY40R
HKY30R
HKY40R
MTJNR/L
MTENN
MTQNR/L
2020K16
SLSTN33
CCP13
CCK13
SLCS105
CPT13
WPS1
MES2
2525M16
SLSTN33
CCP13
CCK13
SLCS105
CPT13
WPS1
MES2
2525M22
SLSTN43
CCP14
CCK14
SLCS106
CPT14
WPS1
MES3
MTNNR/L
5032M22
SLSTN43
CCP14
CCK14
SLCS106
CPT14
WPS1
MES3
WPSWN43
CCP34
CCK13
SLCS105
CPT24
MES2
HKY25R
HKY30R
HKY40R
Shim
Shim Pin
Clamp
Bridge
Clamp
Screw
Side Lock
Plate
Lock
Screw
Spring
Wrench
2020K16N
WPSTN33
CCP33
CCK13
SLCS105
CPT13
MES2
2525M16N
WPSTN33
CCP33
CCK13
SLCS105
CPT13
MES2
2525M22N
WPSTN43
CCP34
CCK14
SLCS106
CPT14
MES3
5032M22N
WPSTN43
CCP34
CCK14
SLCS106
CPT14
MES3
HKY25R
HKY40R
HKY25R
HKY40R
HKY30R
HKY40R
HKY30TL
HKY40R
2020K08
MWLNR/L
2525M08
3225P08
WP TYPE HOLDER
Type
MTENN
MTQNR/L
MTNNR/L
Size

Type
SDJCR/L
SDFCR/L
SDXCR/L
SVJCR/L
SVVCN
SVPCR/L
SSBCR/L
SRGCR/L
SRXCR/L
SRDCN
Size
0808D07
1010E07
1212F07
1616H11
0808D11
1010E11
1212F16
3225P16
1616H09
0808D06
1010E06
1212F06
1010E08
1212F08
Clamp Screw
Wrench
Shim
Shim Pin
TS25
TS25
TKY08F
TKY08F
TS25
TS43
TKY08F
TKY15F
TS25
TS25
TKY08F
TKY08F
TS43
TS44
TKY15F
TKY15R
SPSVN32
BCP141
TS43
TKY15F
TS25
TS25
TKY08F
TKY08F
TS25
TKY08F
TS3
TS3
TKY08F
TKY08F
SPARE PARTS
SP TYPE HOLDER
P019
SPARE PARTS

(TURNING HOLDERS)
MP TYPE HOLDER
Type
Size
PVVNN
PVPNR/L
3225P16
Shim
Lock Pin
Lock Screw
Stop Ring
Wrench
PV32p
P11S
HSP05008C
E03
HKY25R
Clamp Screw
Wrench
SR TYPE HOLDER
Type
Size
SRSGR/L
SRSGN
2525M20
3225P20
Clamp Screw
Wrench
TS5
TS5
TKY25F
TKY25F
AL TYPE HOLDER
Type
Size
PTGER/L
PTFER/L
2020K16
2525M16
1616H16
2020K16
2525M16
SVVDN
SVPDR/L
Shim
Shim Pin
Clamp Lever
LLSTE32
LLSTE32
LLP13
LLP13
LLCL131
LLCL131
LLCS106
LLCS106
HKY25R
HKY25R
FC400890T
FC400890T
FC400890T
TKY10F
TKY10F
TKY10F
MT2 TYPE HOLDER

Type
Size
MT2R/L
2525M4
Clamp Bridge
Clamp Screw
Spring
Wrench
MTK1L/R
HBH06020
MES3
HKY40R
Clamp Bridge
Clamp Screw
Spring
Wrench
MTK1R/L
MTK1R/L
MTK1R/L
HBH06020
HBH06020
HBH06020
MES3
MES3
MES3
HKY40R
HKY40R
HKY40R
Clamp Bridge
Clamp Screw
Spring
Wrench
MTK1L/R
MTK1L/R
HBH06020
HBH06020
MES3
MES3
HKY40R
HKY40R
MTK2L/R
MGS6
MES3
HKY50R
MTK2L/R
MTK2L/R
MGS6
MGS6
MES3
MES3
HKY50R
HKY50R
MG2 TYPE HOLDER

Type
Size
MG2R/L
2525M4315
2525M4323
2525M4333
SPARE PARTS
MG TYPE HOLDER
P020

Type
Size
MGHR/L
2020K3333
2020K4447
3232P5660
3232P5670
3232P5680
EG TYPE HOLDER
Type
Size
EGHR
2020K03
2525M3
2525M4
2525M5
2525M7
2525M8
Clamp Screw
Wrench
EGS06019
EGS06019
HKY30R
HKY30R
EGS08024
HKY40R
EGS08024
HKY40R
EGS08024
EGS08024
HKY40R
HKY40R
ET TYPE HOLDER
Type
Size
ETHR
2525M16
Clamp Bridge
Clamp Screw
Shim Screw
CK341
LS2
CFM02008
Shim
PT32T1R
PT32T2R
Breaker Piece
Wrench
CBT3106
CBT3113
HKY40R
CBT3120
SET TYPE HOLDER

Type
Size
SETHR
1616H16
2020K16
2525M16
Clamp Bridge
Clamp Screw
Stop Ring
Shim Pin
Shim
Wrench
SETK51
SETK51
SETK51
SETS51
SETS51
SETS51
CR4
CR4
CR4
HFC03008
HFC03008
HFC03008
CT32T1
CT32T1
CT32T1
TKY15F
HKY20R
TKY15F
HKY20R
TKY15F
HKY20R
Locator Screw
Clamp Screw
Spring
Wrench
H63TH-DGHR/LS
H63TH-DGHR/L
H63TH-DGHN-H4
H63TH-DGHN-H5
H63TH-DGHN-H6
H63TH-DGHN-L4
H63TH-DGHN-L5
H63TH-DGHN-L6
HSC05012
HSC05012
DGS51
DGS51
MES2
MES2
HKY40R
HKY40R
HSC05010
DGS51
MES2
HKY40R
HSC05012
DGS51
MES2
HKY40R
HSC05012
DGS51
MES2
HKY40R
HSC05010
DGS51
MES2
HKY40R
HSC05012
HSC05012
DGS51
DGS51
MES2
MES2
HKY40R
HKY40R
SPARE PARTS
HSK-T TOOLS (DG)
P021
SPARE PARTS

(TURNING HOLDERS)
SPARE PARTS
DG TYPE HOLDER
P022
Clamp Bridge
Locator Screw
Wrench
Clamp Screw
Spring
DGHR/L 1616K2G
DGHR/L 1616K3
DGHR/L 1616K3G
DGHR/L 1616KF3
DGHR/L 2020K
DGHR/L 2020KFS
DGHR/L 2020KL
DGHR/L 2020KLS
DGHR/L 2020KS
DGHR/L 2525M
DGHR/L 2525MC
DGHR/L 2525MCS
DGHR/L 2525MF
DGHR/L 2525MFS
DGHR/L 2525ML
DGHR/L 2525MLS
DGHR/L 2525MS
DGK2R/L
DGK3R/L
HKY40R
HKY40R
DGS51
DGS51
MES2
MES2
DGK3R/L
HKY40R
DGS51
MES2
DGK3R/L
HKY40R
DGS51
MES2
HSC04014
DGS51
MES2
HSC04014
DGS51
MES2
HSC04014
DGS51
MES2
HSC04014
DGS51
MES2
HSC04014
HKY30R
HKY40R
HKY30R
HKY40R
HKY30R
HKY40R
HKY30R
HKY40R
HKY30R
HKY40R
DGS51
MES2
HSC05012
HKY40R
DGS51
MES2
HSC05012
HKY40R
DGS51
MES2
HSC05010
HKY40R
DGS51
MES2
HSC05012
HKY40R
DGS51
MES2
HSC05012
HKY40R
DGS51
MES2
HSC05012
HKY40R
DGS51
MES2
HSC05012
HSC05012
HKY40R
HKY40R
DGS51
DGS51
MES2
MES2

(BORING BARS)
COBRA (STEEL SHANK)
Clamp Screw
Wrench
S08HSTFPR09
S10KSTFPR09
SoooSTFPR11
SoooSTFPR16
SoooSCLPR/L08
SoooSCLPR/L09
SoooSWLPR/L04
SoooSWLPR/L06
TS253
TS25
TKY08F
TKY08F
TS3
TKY08F
TS4
TKY15F
TS3
TKY08F
TS4
TKY15F
TS25
TS4
TKY08F
TKY15F
COBRA (CARBIDE SHANK)

Clamp Screw
Wrench
E08KSTFPR09
E10MSTFPR09
EoooSTFPR11
EoooSCLPR08
EoooSCLPR09
TS253
TS25
TKY08F
TKY08F
TS3
TKY08F
TS3
TS4
TKY08F
TKY15F
S TYPE (STEEL SHANK)

Clamp Screw
Wrench
SoooSSKCR/L12
SoooSDQCR/L15
SoooSCZCR/L06
SoooSCZCR/L09
SoooSCZCR/L12
SoooSDZCR11
TS5
TS5
TKY25F
TKY25F
TS25
TKY08F
TS4
TKY15F
TS5
TS4
TKY25F
TKY15F
Clamp Screw
Wrench
CoooSSKCR/L09
CoooSDUCR/L15
CoooSVUCR/L11
CoooSVUCR/L16
CoooSCLCR/L12
CoooSCZCR/L06
CoooSCZCR/L09
CoooSCZCR/L12
CoooSDZCR11
TS4
TS5
TKY15F
TKY25F
TS25
TKY08F
TS4
TKY15F
TS5
TKY25F
TS25
TKY08F
TS4
TKY15F
TS5
TS4
TKY25F
TKY15F
SPARE PARTS
S TYPE (CARBIDE SHANK)
P023
SPARE PARTS

(BORING BARS)
F TYPE
Type
Size
116R/L
120R/L
125R/L
132R/L
216R/L
220R/L
225R/L
232R/L
FCSK
FCSK
FCTU
Shim
Shim Pin
Clamp Set
Breaker Piece
Wrench
C3
C3
CBS3
CBS3
HKY25R
HKY25R
PS42
PS42
BCP252
BCP251
C4
C4
CBS4F
CBS4F
HKY30R
HKY30R
PS42
BCP252
C3
C3
C4
CBS3
CBS3
CBS4F
HKY25R
HKY25R
HKY30R
PT32
BCP201
C4
CBT3F
HKY30R
P TYPE
Shim
Shim Pin
Clamp Lever
Clamp Screw
Wrench
Plug
A50UPSKNR/L19
A40TPCLNR/L16
A50UPCLNR/L19
LLSSP63
LLSCN53
LLSCP63
LLP16
LLP15
LLP16
LLCL16
LLCL25
LLCL16
LLCS310
LLCS508
LLCS310
HKY40R
HKY30R
HKY40R
HGM-PT3/8
HGM-PT3/8
HGM-PT3/8
D TYPE (FOR BORING)

Type
Size
DPSK
DPTF
DPDU
DPDH
DPDZ
DPCL
DPVP
SPARE PARTS
DCTU
132R/L
140R/L
150R/L
163R/L
150R/L
163R/L
132R/L
140R/L
150R/L
150R/L
163R/L
150R/L
132R/L
140R/L
150R/L
Shim Pin
Clamp
Lever
Clamp Screw Clamp Set
Breaker
Piece
Stop Ring
Wrench
LLSSN42
LLSSN42
LLP14
LLP14
LLCL14
LLCL14
LLCS108
LLCS108
HKY30R
HKY30R
LLSSN63
LLSSN63
LLP16
LLP16
LLCL16
LLCL16
LLCS110
LLCS110
HKY40R
HKY40R
LLSTN42
LLSTN42
LLP14
LLP14
LLCL14
LLCL14
LLCS108
LLCS108
HKY30R
HKY30R
LLSDN42
LLSDN42
LLSDN53
LLP14
LLP14
LLP15
LLCL24
LLCL24
LLCL15
LLCS108
LLCS108
LLCS208
HKY30R
HKY30R
HKY30R
LLSCN63
LLSCN63
LLP16
LLP16
LLCL16
LLCL16
LLCS110
LLCS110
HKY40R
HKY40R
PV322
P11S
HSP05008C
E03
HKY25R
PT32
PT42
PT42
BCP201
BCP251
BCP251
C4
C5
C5
CBT3N
CBT4F
CBT4F
HKY30R
HKY40R
HKY40R
*DPDH150R/L can be compatible with 140R/L.

D TYPE (FOR GROOVING AND THREADING)
Type
DPT2
DPT4
P024
Shim
Size
132R
140R
132R
140R
Lock Pin
Lock Screw
Stop Ring
Wrench
P21S
P21S
HSP08014
HSP08014
E01
E01
HKY40R
HKY40R
P21S
P21S
HSP08014
HSP08014
E01
E01
HKY40R
HKY40R

Type
FCL5
NTF
SNTF
FCDG4
FCDG4
Size
116R/L
120R/L
125R/L
132R/L
216R/L
220R/L
225R/L
M16R
Q20R
R25R
R216R
S220R
T225R
K16R11
M16R
P20R
R25R
M210R11
Q212R11
R216R
S220R
T225R
120R/L3M
125R/L3M
132R/L3M
120R/L4M
125R/L4M
132R/L4M
125R/L5M
132R/L5M
120R/L4J
125R/L4J
132R/L4J
125R/L5J
132R/L5J
Clamp Bridge
Clamp Set
Clamp Screw
Shim
Shim Pin
Stop Ring
Wrench
LK1
LK1
HBH04012
HBH04012
HKY25R
HKY25R
LK1
HBH04012
HKY25R
LK1
HBH04012
HKY25R
LK1
HBH04012
HKY25R
LK1
LK1
HBH04012
HBH04012
HKY25R
HKY25R
C3
C4
HKY25R
HKY30R
C4
HKY30R
C3
HKY25R
C4
C4
HKY30R
HKY30R
TS25
CS350860T
TKY08F
TKY15F
SETK51
SETS51
CT32T1
HFC03008
CR4
SETK51
SETS51
CT32T1
HFC03008
CR4
TKY15F
HKY20R
TKY15F
HKY20R
TS25
TKY08F
TS25
TKY08F
CS350860T
TKY15F
SETK51
SETK51
SETS51
SETS51
CT32T1
CT32T1
HFC03008
HFC03008
CR4
CR4
TKY15F
TKY15F
BC5
BC5
TKY20R
TKY20R
BC5
TKY20R
BC5
TKY20R
BC5
TKY20R
BC5
TKY20R
BC5
BC5
TKY20R
TKY20R
BC5
BC5
TKY20R
TKY20R
BC5
TKY20R
BC5
BC5
TKY20R
TKY20R
SPARE PARTS
F TYPE (FOR GROOVING AND THREADING)
P025
SPARE PARTS

(BORING UNITS)
UNIT
Washer Screw
Bush Screw
Wrench
NA1
NV1
NA2
NV2
NA3
NV3
NA4
NV4
HFC03008
HFC03008
HY-A1
HY-V1
HKY20R
HKY20R
HSC03010
HSC03010
HY2
HY2
HSC04010
HSC04010
HY3
HY3
HSC05012
HSC05012
HY4
HY4
HKY20R
HKY25R
HS-N2
HKY25R
HKY20R
HKY30R
HKY20R
HKY30R
HKY30R
HKY40R
HKY30R
HKY40R
Bush
Washer
Leaf Spring
The parts above are not sold separately as

accuracy can only be guaranteed by having the
complete set.
Please contact us for questions about parts
replacement.
SPARE PARTS
CARTRIDGE
P026
Clamp Lever
NASP11
NVSP11
NASP21
NVSP21
NAPN21
NVPN21
NASP31
NVSP31
NAPN31
NVPN31
NAPN41
NVPN41
Shim
Shim Pin
Spanner
Wrench
CS250T
CS250T
HR12
HR12
TKY08F
TKY08F
CS300890T
CS300890T
HR12
HR12
TKY08F
TKY08F
LLCS103
LLCS103
HR12
HR12
HKY20F
HKY20F
CS300890T
CS300890T
HR34
HR34
TKY08F
TKY08F
LLCL12S
LLCL12S
LLCS103
LLCS103
HR34
HR34
HKY20F
HKY20F
LLCL13
LLCL13
LLCS106
LLCS106
LLSTN32
LLSTN32
LLP13
LLP13
HR34
HR34
HKY25F
HKY25F
LLCL12S
LLCL12S
Clamp Screw

(FACE MILLS)
AF5000 TYPE
Wedge
Clamp Screw
Adjust Screw
Wrench
Wrench
Recommended
Cutter
AF5000 Type
CWAF5R/L
LS10T
KS1S
TKY25T
HKY15R
NF10000 Type (^L148)
BAP300 TYPE
Clamp Screw
Wrench
Recommended
Cutter
BAP300 Type
TS25
TKY08F
APX3000 Type (^L046)
Clamp Screw
Wrench
Recommended
Cutter
BAP400-040A04R
BAP400-050A05R
BAP400-063A06R
BAP400R0307C
BAP400R0408D
BAP400R0509E
BAP400R0610E
TS43
TS43
TKY15F
TKY15F
TS43
TKY15F
TS43
TKY15F
BAP400 TYPE
TS43
TKY15F
TS43
TS43
TKY15D
TKY15D
BF407 TYPE
Wedge
Clamp Screw
Setting
Screw
Wrench
Recommended
Cutter
BF407R0812K
BF407R1016K
BF407R1218P
CWSF407TR2
CWSF407TR2
CWSF407TR2
LS15T
LS15T
LS15T
CAS51T
CAS51T
CAS51T
TKY25T
TKY25T
TKY25T
Wedge
Clamp Screw
Wrench
Recommended
Cutter
BN425 Type
CWS43SNN
LS14T
TKY25T
BOE TYPE
Set Bolt
Set Bolt
Clamp Screw
Wrench
(Insert)
Wrench
(Set Bolt)
BOER0202B
BOE-050A02R
BOER2H03B
BOE-063A03R
BOER0304C
BOER0405D
LS21
LS20
CS501290T
CS501290T
TKY25T
TKY25T
HKY50R
HKY50R
BOES101
CS501290T
TKY25T
HKY80R
BOES101
CS501290T
TKY25T
HKY80R
HSC16035
CS501290T
CS501290T
TKY25T
TKY25T
Recommended
Cutter
SPARE PARTS
BN425 TYPE
OCTACUT Type (^L094)
P027
SPARE PARTS

(FACE MILLS)
BSX400 TYPE
Clamp Screw
Wrench
BSX400R05004A
BSX400R06305A
BSX400R08006C
BSX400R10008D
BSX400R12510E
BSX400R16012E
TS43
TS43
TKY15F
TKY15F
TS43
TKY15F
TS43
TKY15F
TS43
TS43
TKY15D
TKY15D
Recommended
Cutter
ASX400 Type (^L040)
BSX500 TYPE
Clamp Screw
Shim
Screw
Shim
Wrench
Recommended
Cutter
BSX500 Type
CSF401260T
WCS604010H
STBS500N
TKY20D
ASX400 Type (^L040)
BXD7000 TYPE
Clamp Screw
Wrench
Recommended
Cutter
BXD7000 Type
TS5SL
TKY25D
AXD7000 Type (^L066)
BZC400 TYPE
Clamp Screw
Set Bolt
Wrench (Wedge)
Wrench (Set Bolt)
Recommended
Cutter
BZC400-032A03R
BZC400-040A04R
BZC400R0408D
CS350990T
CS350990T
CS350990T
LS24
TKY10F
TKY10F
TKY10F
HKY40R
SPARE PARTS
E404 TYPE
Locator
Locator
Screw
Shim
Shim
Screw
Wedge
E404 Type
SSE41R
SPS1
SCD43
STS1
CWS3R/L
Clamp
Screw
Wrench Wrench
(Wedge)
WS1
TKY10R TKY25T
Recommended
Cutter
FN548 TYPE
Wedge
Clamp Screw
Wrench
FN548 Type
CWS4
LS14
HKY40T
0
Wrench
Hexagonal
Head
120QSPK x 80
6.35r x 4
(KANNON-SEIKI CO.) (KYOKUTO MFG CO.)
Recommended
Cutter
LSE445 TYPE
LSE445 Type
P028
Shim
Shim
Screw
Wedge
STBE445NF CS300890T CWSE445TR
Clamp Screw
Wrench
(Wedge)
Wrench
Recommended
Cutter
LS15T
TKY25T
TKY08F
ASX445 Type (^L018)
MG300, 400 TYPE

Clamp Screw
Wrench
Recommended
Cutter
MG300 Type
MG400 Type
CS350990T
CS451190T
TKY10F
TKY20F
ASX400 Type (^L040)
Clamp Screw
Wrench
Recommended
Cutter
MG345 Type
MG445 Type
CS350990T
CS451190T
TKY10F
TKY20F
ASX445 Type (^L018)
Clamp Screw
Wrench
Recommended
Cutter
MGP445 Type
CS401160T
TKY15D
ASX445 Type (^L018)
MG345, 445 TYPE
MGP445 TYPE
MSD445 TYPE
Wedge
Clamp Screw
Wrench
Recommended
Cutter
MSD445 Type
CWMSE445R2
LS15T
TKY25T
ASX445 Type (^L018)
Wedge
Clamp Screw
Wrench
Recommended
Cutter
MSE445 Type
CWMSE445R2
LS15T
TKY25T
ASX445 Type (^L018)
MSE445 TYPE
Wedge
Clamp Screw Adjusting Wedge Adjusting Screw Clamp Screw
NR10000 Type
CWAF10R2
LS10T
CWAF10N
LS15T
CSAF10
Wrench
Recommended
Cutter
TKY25T
P425, P525 TYPE

Clamp
Screw
Wrench Wrench
(Wedge)
Locator
Locator
Screw
Shim
Shim
Screw
Wedge
Recommended
Cutter
P425 Type
SSP41R
SPS1
SCP431R/L
STS1
CWS1R/L
WS1
TKY10R TKY25T ASX445 Type (^L018)
P525 Type
SSP51R
SPS1
SCP521R/L
STS1
CWS1R/L
WS1
TKY10R TKY25T SE515 Type (^L034)
SPARE PARTS
NR10000 TYPE
QBF407 TYPE
Wedge
Clamp Screw
Setting
Screw
Guide Plate
Stop Screw
Wrench
Recommended
Cutter
QBF407R0304Q
QBF407R0406Q
QBF407R0508Q
CWSF407TR1
CWSF407TR1
CWSF407TR2
LS15T
LS15T
LS15T
CAS51T
CAS51T
CAS51T
QPAR1
QPAR1
QPAR1
TFC04010
TFC04010
TFC04010
TKY20R
TKY25T
TKY20R
TKY25T
TKY20R
TKY25T
P029
SPARE PARTS

(FACE MILLS)
QBP415 TYPE
Shim
Shim Pin
Wedge-T
Clamp
Screw
Wrench
Recommended
Cutter
QBP415 Type
STSP415R
TS32
QWGR1
LS10T
TKY25T
QF10000 TYPE
Wedge
Clamp
Screw
QF10000 Type
CWAF10R3
LS15T
Guide Plate Stop Screw Adjusting Wedge Adjusting Screw Stop Screw Wrench
QPCR1 TFC04010 CWAF10N
CSAF10 TKY20T
TKY25T
LS10T
Recommended
Cutter
QSE415 TYPE
Wedge
Clamp
Screw
Setting
Screw
Guide Plate
Stop Screw
Wrench
Recommended
Cutter
QSE415 Type
CWSF407TR3
LS15T
CAS51T
QPAR1
TFC04010
TKY20R
TKY25T
SE300 TYPE
SE300 Type
Locator
Locator
(Wiper)
Wedge-T
Wedge-S
Wedge-S
(Wiper)
Clamp
Screw
Wrench
SPSE300R SPSEW300R CWNSE300TR CWSE300SN CWSEW300SN LS10T TKY25T
Recommended
Cutter
SE400 TYPE
SE400 Type
Locator
Locator
(Wiper)
Wedge-T
Wedge-S
Clamp
Screw
Wrench
SPSE400R SPSEW400R CWSE400TN CWSE400SN LS15T

(SE400R0304C:LS10T) TKY25T
Recommended
Cutter
SHP400 TYPE
SHP400 Type
Locator
Wedge-T
SPSHP400R/L CWSE300TR/L
Clamp
Screw
Locator
Screw
Wrench
(Wedge)
Wrench
(Locator)
Recommended
Cutter
LS10T
TS32
TKY25T
TKY08F
ASX400 Type (^L040)
SPARE PARTS
VIP400 TYPE
Clamp Screw
Wrench
Recommended
Cutter
VIP400 Type
CS501160T
TKY20F
ASX400 Type (^L040)
Clamp Screw
Wrench
Recommended
Cutter
VIP445 Type
CS501160T
TKY20F
ASX445 Type (^L018)
VIP445 TYPE
VSD645 TYPE
P030
Locator
Locator Screw
Clamp
Screw
Adjust
Screw
Wrench
(Insert)
Wrench
Recommended
Cutter
VSD645 Type
NE04R30
SE03-65
SE02-81
SA04-47
TKY15D
HKY30R
ASX445 Type (^L018)
SPARE PARTS

(END MILLS)
BAE TYPE
Clamp Screw
BAE500R161S16
BAE500R201S20
BAE500R252S25
BAE500R323S32
BAE500R403S32
BAE500R504S32
BAE600 Type
Recommended
End Mill
Wrench
TS42
TS42
TKY15F
TKY15F
TS42
TKY15F
TS4
TKY15F
TS4
TS4
TKY15F
TKY15F
TS52
TKY25F
BAP400 TYPE
Clamp Screw
BAP400R252S25
BAP400R323S32
BAP400R404S32
BAP400R505S32
BAP400R636S32
Recommended
End Mill
Wrench
TS4
TS43
TKY15F
TKY15F
TS43
TKY15F
TS43
TS43
TKY15F
TKY15F
BAEP400 (Long Cutting Edge Type) TYPE

Clamp Screw
BAP400R4008ES42
BAP400R5012ES58
BAP400R06308C
BAP400R08012D
BAP400R06312A27
BAP400R08018A27
Recommended
End Mill
Wrench
TS43
TS43
TKY15F
TKY15F
TS43
TKY15F
TS43
TKY15F
TS43
TS43
TKY15F
TKY15F
BOE TYPE
Clamp Screw
Wrench
Recommended
End Mill
BOE Type
CS501290T
TKY25T
OCTACUT Type (^L094)
Clamp Screw
Clamp Bridge
Clamp Screw
(Bridge)
Spring
Wrench
Recommended
End Mill
BRE Type
TS5S
AMS5
BRS105
ASS3
TKY25R
BRP Type (^L102)
BSX300 TYPE
Clamp Screw
Wrench
Recommended
End Mill
BSX300 Type
TS32
TKY08F
Clamp Screw
Wrench
Recommended
End Mill
BSX400 Type
TS43
TKY15F
ASX400 Type (^L040)
SPARE PARTS
BRE TYPE
BSX400 TYPE
BSX500 TYPE
Clamp Screw
Shim
Screw
Shim
Wrench
Recommended
End Mill
BSX500 Type
CSF401260T
WCS604010H
STBS500N
TKY20D
ASX400 Type (^L040)
P031
SPARE PARTS

(END MILLS)
BXD7000 TYPE
Clamp Screw
BXD7000R251SA25SA/B
BXD7000R321SA32SA/B
BXD7000R402SA42SA/B
TS5S
TS5S
TS5SL
Wrench
Recommended
End Mill
TKY25D
TKY25D
TKY25D
AXD7000 Type (^L066)
BZC400 TYPE
Clamp Screw
Wrench
Recommended
End Mill
BZC400 Type
CS350990T
TKY10F
CV TYPE
Clamp Screw
Clamp Bridge
Clamp Screw
(Bridge)
Spring
Wrench
Recommended
End Mill
CV10R253S32
CV12R323S32
CV16R403S32
TS4
TS4
TS5
AMS3
AMS3
AMS5
BRS103
BRS103
BRS105
ASS2
ASS2
ASS3
TKY15R
TKY15R
TKY25R
BRP Type (^L102)
CV20 TYPE
Clamp Screw
Wedge
Wrench
Recommended
End Mill
CV20R403S32
LS14T
CWCV20
TKY25T
DCSD, DCSN TYPE

Holder
SPARE PARTS
DCSDR2063SN
DCSDR2063LN
DCSDR2080SN
DCSDR2100SN
DCSNR2063SN
DCSNR2063LN
DCSDR2063SB
DCSDR2063LN
DCSNR2063SB
DCSDR2080SA
DCSNR2080SA
Cartridge
Recommended
End Mill
Clamp
Screw
Body
Shim
Shim
Screw
TS5S
TS5S
JKDS4
JKDS4
DKS5 HKY40R TKY25T

DKS5 HKY40R TKY25T
TS5S
TS5S
JKDS4
JKDS4
DKS5 HKY40R TKY25T

DKS5 HKY40R TKY25T
JENS42
JENS42
JSS7
JSS7
TS5L
TS5L
JKNS4 JENS42 JSS7

JKNS4 JENS42 JSS7
DKS5 HKY40R TKY25T

DKS5 HKY40R TKY25T SPX Type (^L108)
TS5S
TS5S
JKDS4
JKDS4
DKS5 HKY40R TKY25T

DKS5 HKY40R TKY25T
JENS42
JSS7
TS5L
JKNS4 JENS42 JSS7
TS5S
JKDS4
JENS42
JSS7
TS5L
JKNS4 JENS42 JSS7
Clamp
Screw
Wrench
Shim
Shim
Screw
Wrench
DKS5 HKY40R TKY25T

DKS5 HKY40R TKY25T
DKS5 HKY40R TKY25T
ECMP TYPE
Clamp Screw
Wrench
Recommended
End Mill
ECMP252S25
ECMP322S32
ECMP402S42
TS4
TS5
TS5
TKY15R
TKY25R
TKY25R
FF3000 TYPE
Shim
Lock Pin
Wrench
Recommended
End Mill
FF3000 Type
FFSS
FFP
HKY25L
FSTE TYPE
P032
Locator
Wedge
Clamp Screw
Locator Screw
Wrench
Recommended
End Mill
FSTE Type
TS441R
CWFSTE
LS10T
CPM03008
TKY25T
ASX400 Type (^L040)
MG200, 300 TYPE

Clamp Screw
Wrench
Recommended
End Mill
MG200 Type
MG300 Type
CS300890T
CS350990T
TKY08F
TKY10F
ASX400 Type (^L040)
Clamp Screw
Wrench
Recommended
End Mill
MG245 Type
MG345 Type
CS300890T
CS350990T
TKY08F
TKY10F
ASX445 Type (^L018)
MG245, 345 TYPE
MSE445 TYPE
Wedge
Clamp Screw
Wrench
Recommended
End Mill
MSE445 Type
CWMSE445R1
LS15T
TKY25T
ASX445 Type (^L018)
SRE TYPE
Clamp Screw
Clamp Bridge
Stop Ring
Wrench
SRER100SS16
SRER120SS16
SRER140SS16
SRER160SS16
SRER180SS20
SRER200SS20
SRER200SL20
SRER250SS25
SRER250SL25
SRER300SS32
SRER300SL32
TS253
TS3
TKY08F
TKY08F
TS3
TKY08F
TS35
TS35
TKY10F
TKY10F
SRS5
SRS5
SRK1R
SRK1R
CR4
CR4
TKY20F
TKY20F
SRS5
SRK1R
CR4
TKY20F
SRS5
SRK1R
CR4
TKY20F
SRS5
SRS5
SRK1R
SRK1R
CR4
CR4
TKY20F
TKY20F
Recommended
End Mill
AQX Type (^L076)
SE300 TYPE
Locator
SE300 Type
SPSE300R
Wedge-T
Wedge-S
CWNSE300TR CWSE300SN
Clamp
Screw
Wrench
Recommended
End Mill
LS10T
TKY25T
SHP400 Type
Locator
Wedge-T
SPSHP400R CWSE300TR
Clamp
Screw
Locator
Screw
Wrench
(Insert)
Wrench
(Locator)
Recommended
End Mill
LS10T
TS32
TKY25T
TKY08F
ASX400 Type (^L040)
VIPER TYPE
Clamp
Screw
Wrench
Recommended
End Mill
VIPER Type
CS400990T
TKY15D
SPX Type (^L108)
Clamp
Screw
Wrench
Recommended
End Mill
TS25
CS300890T
TKY08F
TKY08F
CS300990T
TKY10F
CS451190T
CS451190T
TKY20F
TKY20F
SPARE PARTS
SHP400 TYPE
ZR TYPE
ZR202C/T
ZR252C/T
ZR322C/T
ZR402C/T
ZR502C/T
P033
SPARE PARTS

(END MILLS)
FBE2 TYPE
Clamp Screw
Wrench
Recommended
End Mill
FBE2200SM
FBE2250SM
FBE2300SM
FBE2200SF
FBE2250SF
FBE2300SF
CS300590T
CS350790T
CS400990T
CS300590T
CS350790T
CS400990T
TKY08R
TKY10R
TKY15R
TKY08R
TKY10R
TKY15R
SRF Type (^L120)
TBE1/TBE2 TYPE
TBE1100SS
TBE1100SM
TBE1100S
TBE1150S
TBE1200S
TBE1250S
TBE1300S
TBE2200S
TBE2200SM
TBE2250S
TBE2250SM
TBE2300S
TBE2300SM
TBE1150SU
TBE1200SU
TBE1250SU
TBE1300SU
TBE2200SU
TBE2250SU
TBE2300SU
TBE1200SL
TBE1250SL
TBE1300SL
TBE2200SL
TBE2250SL
TBE2300SL
Clamp Screw
Wrench
Peripheral
TS3
TS3
TS3
CS300790TS
CS400990T
CS400990T
CS501290T
CS350790T
CS350790T
CS400990T
CS400990T
CS501290T
CS501290T
CS300790TS
CS400990T
CS400990T
CS501290T
CS350790T
CS400990T
CS501290T
CS400990T
CS400990T
CS501290T
CS350790T
CS400990T
CS501290T
TS3
TS3
TS4
CS350790T
CS400990T
CS400990T
TKY08F
TKY08F
TKY08F
Peripheral
TKY10R
TKY15R
TKY15R
TKY25R
TKY10R
TKY10R
TKY15R
TKY15R
TKY25R
TKY25R
TKY10R
TKY15R
TKY15R
TKY25R
TKY10R
TKY15R
TKY25R
TKY15R
TKY15R
TKY25R
TKY10R
TKY15R
TKY25R
TKY08F
TKY08F
TKY15R
TKY10R
TKY15R
TKY15R
Recommended
End Mill
SRM2 Type (^L128)
SPARE PARTS
TBE2 TYPE
Clamp Screw
Wrench
Recommended
End Mill
TBE2150S/SM/SU
TBE2160S/SM/SU
TS254
TS254
TKY08F
TKY08F
SRM2 Type (^L128)
TRM2 TYPE
TRM2200SM
TRM2250SM
TRM2300SM
TRM2200SL
TRM2250SL
TRM2300SL
TRM2200SF
TRM2250SF
TRM2300SF
P034
Clamp Screw
Wrench
Inner, Outer
Peripheral
Inner, Outer
Peripheral
CS300790TS
CS400990T
CS501290T
CS300790TS
CS400990T
CS501290T
CS300790TS
CS400990T
CS501290T
TS3
TS3
TS4
TS3
TS3
TS4
TKY10R
TKY15R
TKY25R
TKY10R
TKY15R
TKY25R
TKY10R
TKY15R
TKY25R
TKY08F
TKY08F
TKY15R
TKY08F
TKY08F
TKY15R
Recommended
End Mill
SRM2 Type (^L128)
SPARE PARTS

(DRILLS)
Old Type
Tool Number
TASS1600S32
TASS1700S32
TASS1800S32
TASS1900S32
TASS2000S32
TASS2100S32
TASS2200S32
TASS2300S32
TASS2400S32
TASS2500S32
TASS2600S32
TASS2700S32
TASS2800S32
TASS2900S32
TASS3000S32
TASS3100S32
TASS3200S32
TASS3300S40
TASS3400S40
TASS3500S40
TASS3600S40
Clamp Screw
Wrench
TS202
TS202
TKY06F
TKY06F
TS202
TKY06F
TS202
TKY06F
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
TS32
TKY08F
TS32
TKY08F
TS32
TKY08F
TS32
TKY08F
TS32
TKY08F
TS43
TKY15F
TS43
TKY15F
TS43
TKY15F
TS43
TKY15F
TS43
TKY15F
TS43
TS43
TKY15F
TKY15F
TASS TYPE (FLANGE)

Recommended
Drill
TAF Drill
(^N240)
Old Type
Tool Number
TASS1600C20
TASS1650C20
TASS1700C20
TASS1750C20
TASS1800C20
TASS1850C20
TASS1900C20
TASS1950C20
TASS2000C20
TASS2100C25
TASS2200C25
TASS2300C25
TASS2400C25
TASS2500C25
TASS2600C25
TASS2700C25
TASS2800C25
TASS2900C25
TASS3000C25
TASS3100C32
TASS3200C32
TASS3300C32
TASS3400C32
TASS3500C32
TASS3600C32
TASS3700C32
TASS3800C32
TASS3900C32
TASS4000C32
TASS4100C32
TASS4200C40
TASS4300C40
TASS4400C40
TASS4500C40
TASS4600C40
TASS4700C40
TASS4800C40
TASS4900C40
TASS5000C40
Clamp Screw
Wrench
TS202
TS202
TKY06F
TKY06F
TS202
TKY06F
TS202
TKY06F
TS202
TKY06F
TS202
TKY06F
TS202
TKY06F
TS202
TKY06F
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
TS32
TKY08F
TS32
TKY08F
TS32
TKY08F
TS32
TKY08F
TS32
TKY08F
TS43
TKY15F
TS43
TKY15F
TS43
TKY15F
TS43
TKY15F
TS43
TKY15F
TS43
TKY15F
TS43
TKY15F
TS43
TKY15F
TS43
TKY15F
TS43
TKY15F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TS32
TKY25F
TKY08F
Recommended
Drill
TAF Drill
(^N240)
SPARE PARTS
TASS TYPE (STANDARD)
P035
SPARE PARTS

(DRILLS)
TAGS TYPE
SPARE PARTS
Old Type
Tool Number
P036
TAGS1600F25
TAGS1700F25
TAGS1800F25
TAGS1900F25
TAGS2000F25
TAGS2100F25
TAGS2200F25
TAGS2300F25
TAGS2400F25
TAGS2500F32
TAGS2600F32
TAGS2700F32
TAGS2800F32
TAGS2900F32
TAGS3000F40
TAGS3100F40
TAGS3200F40
TAGS3300F40
TAGS3400F40
TAGS3500F40
TAGS3600F40
TAGS3700F40
TAGS3800F40
TAGS3900F40
TAGS4000F40
TAGS4100F40
TAGS4200F40
TAGS4300F40
TAGS4400F40
TAGS4500F40
TAGS4600F40
TAGS4700F40
TAGS4800F40
TAGS4900F40
TAGS5000F40
TAGS5100F40
TAGS5200F40
TAGS5300F40
TAGS5400F40
TAGS5500F40
TAGS5600F40
TAGS5700F40
TAGS5800F40
TAGS5900F40
TAGM TYPE
Clamp Screw
Wrench
TS2
TS2
TKY06F
TKY06F
TS2
TKY06F
TS2
TKY06F
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
TS3
TKY08F
TS3
TKY08F
TS3
TKY08F
TS3
TKY08F
TS3
TKY08F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS3
TKY08F
TS3
TKY08F
TS3
TKY08F
TS3
TKY08F
TS3
TKY08F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TS4
TKY15F
TKY15F
Recommended
Drill
Old Type
Tool Number
TAF Drill
(^N240)
TAGM1600F25
TAGM1700F25
TAGM1800F25
TAGM1900F25
TAGM2000F25
TAGM2100F25
TAGM2200F25
TAGM2300F25
TAGM2400F25
TAGM2500F32
TAGM2600F32
TAGM2700F32
TAGM2800F32
TAGM2900F32
TAGM3000F40
TAGM3100F40
TAGM3200F40
TAGM3300F40
TAGM3400F40
TAGM3500F40
TAGM3600F40
TAGM3700F40
TAGM3800F40
TAGM3900F40
TAGM4000F40
TAGM4100F40
TAGM4200F40
TAGM4300F40
TAGM4400F40
TAGM4500F40
TAGM4600F40
TAGM4700F40
TAGM4800F40
TAGM4900F40
TAGM5000F40
TAGM5100F40
TAGM5200F40
TAGM5300F40
TAGM5400F40
TAGM5500F40
TAGM5600F40
TAGM5700F40
TAGM5800F40
TAGM5900F40
Clamp Screw
Wrench
TS2
TS2
TKY06F
TKY06F
TS2
TKY06F
TS2
TKY06F
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
TS25
TKY08F
TS3
TKY08F
TS3
TKY08F
TS3
TKY08F
TS3
TKY08F
TS3
TKY08F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS5
TKY25F
TS3
TKY08F
TS3
TKY08F
TS3
TKY08F
TS3
TKY08F
TS3
TKY08F
TS4
TKY15F
TS4
TKY15F
TS4
TKY15F
TS4
TS4
TKY15F
TKY15F
Recommended
Drill
TAF Drill
(^N240)
TAB TYPE
NPX TYPE
Clamp
Screw
Plug
Wrench
TAB1700S32
TAB1800S32
TAB1900S32
TAB2000S32
TAB2100S32
TAB2200S32
TAB2300S32
TAB2400S32
TAB2500S32
TAB2600S32
TAB2700S32
TAB2800S32
TAB2900S32
TAB3000S32
TAB3100S32
TAB3200S32
TAB3300S40
TAB3400S40
TAB3500S40
TAB3600S40
TAB3700S40
TAB3800S40
TAB3900S40
TAB4000S40
TAB4100S40
TAB4200S40
TAB4300S40
TAB4400S40
TAB4500S40
TS3
TS3
PT1/4
PT1/4
TKY08D
TKY08D
TS3
PT1/4
TKY08D
TS32
PT1/4
TKY08D
TS32
PT1/4
TKY08D
TS32
PT1/4
TKY08D
TS32
PT1/4
TKY08D
TS32
PT1/4
TKY08D
TS32
PT1/4
TKY08D
TS4
PT1/4
TKY15D
TS4
PT1/4
TKY15D
TS4
PT1/4
TKY15D
TS4
PT1/4
TKY15D
TS4
PT1/4
TKY15D
TS4
PT1/4
TKY15D
TS4
PT1/4
TKY15D
TS5
PT1/4
TKY25D
TS5
PT1/4
TKY25D
TS5
PT1/4
TKY25D
TS5
PT1/4
TKY25D
TS5
PT1/4
TKY25D
TS5
PT1/4
TKY25D
TS5
PT1/4
TKY25D
TS5
PT1/4
TKY25D
TS5
PT1/4
TKY25D
TS5
PT1/4
TKY25D
TS5
PT1/4
TKY25D
TS5
TS5
PT1/4
PT1/4
TKY25D
TKY25D
Recommended
Drill
Old Type
Tool Number
Clamp
Screw
Wrench
NPXM2000S25
NPXM2100S25
NPXM2200S25
NPXM2300S25
NPXM2400S32
NPXM2500S32
NPXM2600S32
NPXM2700S32
NPXM2800S32
NPXM2900S32
NPXM3000S32
TS3
TS3
TKY08F
TKY08F
TS3
TKY08F
TS35
TKY10F
TS35
TKY10F
TS35
TKY10F
TS35
TKY10F
TS4
TKY15F
TS4
TKY15F
TS4
TS4
TKY15F
TKY15F
Recommended
Drill
TAW Drill
(^N229)
TAF Drill
(^N240)
SPARE PARTS
Old Type
Tool Number
P037
SPARE PARTS
ANTI SEIZE LUBRICANT

ANTI SEIZE LUBRICANT
SPARE PARTS
Shape
P038
Order Number
Stock
Volume
(g)
MK1K
20
MK1KS
TECHNICAL DATA
TROUBLE SHOOTING FOR TURNING ...........................................................Q002
CHIP CONTROL FOR TURNING .....................................................................Q004
EFFECTS OF CUTTING CONDITIONS FOR TURNING..................................Q005
FUNCTION OF TOOL FEATURES FOR TURNING .........................................Q007
FORMULAE FOR CUTTING POWER .............................................................. Q011
TROUBLE SHOOTING FOR FACE MILLING ..................................................Q012
FUNCTION OF TOOL FEATURES FOR FACE MILLING ................................Q013
FORMULAE FOR FACE MILLING ...................................................................Q016
TROUBLE SHOOTING FOR END MILLING ....................................................Q018
END MILL TERMINOLOGY ..............................................................................Q019
TYPES AND SHAPES OF END MILLS ............................................................Q020
PITCH SELECTION OF PICK FEED ................................................................Q021
TROUBLE SHOOTING FOR DRILLING ..........................................................Q022
DRILL WEAR AND CUTTING EDGE DAMAGE ..............................................Q023
DRILL TERMINOLOGY AND CUTTING CHARACTERISTICS .......................Q024
FORMULAE FOR DRILLING............................................................................Q027
METALLIC MATERIALS CROSS REFERENCE LIST .....................................Q028
DIE STEELS......................................................................................................Q032
SURFACE ROUGHNESS .................................................................................Q034
HARDNESS COMPARISON TABLE ................................................................Q035
JIS FIT TOLERANCE HOLE ............................................................................Q036
JIS FIT TOLERANCE SHAFT ..........................................................................Q038
DRILL DIAMETERS FOR PREPARED HOLES ...............................................Q040
HEXAGON SOCKET HEAD BOLT HOLE SIZE...............................................Q041
TAPER STANDARD ..........................................................................................Q042
INTERNATIONAL SYSTEM OF UNITS ............................................................Q043
SYSTEM OF UNITSTOOL WEAR AND DAMAGE ..........................................Q044
CUTTING TOOL MATERIALS ..........................................................................Q045
GRADE CHAIN .................................................................................................Q046
GRADES COMPARISON TABLE .....................................................................Q047
INSERT CHIP BREAKER COMPARISON TABLE ...........................................Q053
Q001
TECHNICAL DATA
TROUBLE SHOOTING
Improper cutting
edge geometry
Improper
tool grade
Out of Tolerance
Deterioration of
Surface Finish
Generation
of Heat
TECHNICAL DATA
Q002
Workpiece over
heating can
cause poor
accuracy and
short life of insert
Thermal crack
occurs
Dry
Wet
Poor insert
accuracy
Large cutting resistance

and cutting edge flank
Improper
cutting conditions
Welding occurs
Improper cutting
edge geometry
Wet
Chattering
Improper
cutting conditions
Improper cutting
edge geometry
Lack of rigidity
Poor finished
surface
Wet
Lack of cutting
edge strength.
Improper
tool grade
Build-up edge
occurs
Necessary to
adjust often
because of
over-size
Improper
cutting conditions
Dimensions
are not
constant
Decrease power and machine

backlash
Down
Decrease holder overhang
Up
Class of insert
Honing strengthens
the cutting edge
Lead angle
Corner radius
Rake
Select chip breaker
Depth of cut
Do not use watersoluble cutting fluid

Determine dry or
wet cutting
Down
Coolant
Machine,
Installation of Tool
Improper
cutting speed
Chipping or
fracturing of
cutting edge
Feed
Cutting speed
Up
Style and Design

of the Tool
Increase clamping rigidity of

the tool and workpiece
Deterioration of Tool Life
Insert wear
quickly
generated
Cutting
Conditions
Improve tool holder rigidity
Improper
tool grade
Select a grade with better

thermal shock resistance
adhesion resistance
Factors
Select a tougher grade
Trouble
Select a harder grade
Solution
Insert Grade
Selection
FOR TURNING
Small chip
control range
Improper cutting
edge geometry
Class of insert
Wet
Dry
TECHNICAL DATA
Improper cutting
edge geometry
Chips are short

and scattered
Wet
Large chip
control range
Improper
cutting conditions
Vibration occurs
long chips
Improper cutting
edge geometry
Improper
cutting conditions
Wet
Vibration occurs
Improper
cutting conditions
Improper cutting
edge geometry
Improper
tool grade

backlash
Improper
cutting conditions
Improper
cutting conditions
Burrs
(mild steel)
Poor Chip Dispersal
Honing strengthens
the cutting edge
Lead angle
Corner radius
Rake
Down
Decrease holder overhang
Burrs, Chipping etc.
Up
Machine,
Improper cutting
edge geometry
Workpiece chipping
(cast iron)
Select chip breaker
Depth of cut
Down
Coolant
Determine dry or
wet cutting
Feed
Cutting speed
Up
Style and Design

of the Tool

Burrs
(steel, aluminium)
Cutting
Conditions
Improve tool holder rigidity
Notch wear

adhesion resistance
Factors
Trouble
Solution
Insert Grade
Selection
Q003
TECHNICAL DATA
CHIP CONTROL FOR TURNING

y CHIP BREAKING CONDITIONS IN STEEL TURNING
Type
A Type
B Type
C Type
D Type
E Type
Curless
l > 50mm
l < 50mm
1 5 Curl
i 1 Curl
Less Than 1
Curl Half a Curl
a Irregular continu-
a Regular continu-
Small Depth
of Cut
d < 7mm
Small Depth
of Cut
d=7 15mm
Curl Length
l
ous shape
a Tangle around tool
and workpiece
Note
ous shape
a Long chips
Good
a Chip scattering
a Chattering
a Poor finished
Good
surface
a Maximum
a Cutting speed and chip control range of chip breaker

In general, when cutting speed increases, the chip control range tends to become narrower.
vc=50m/min
0.6
0.5
Feed (mm/rev)
Feed (mm/rev)
0.5
0.4
0.3
0.2
B
D
C
0.1
0.4
0.3
0.2
0.1
2
0.4
0.3
0.2
D
C
0.1
A
1
Depth of Cut (mm)
vc=150m/min
0.5
A
1
0.6
vc=100m/min
Feed (mm/rev)
0.6
A
1
Depth of Cut (mm)

Workpiece : S45C(180HB)
Tool : MTJNR2525M16N
Insert
: TNMG160408
Dry Cutting
Grade
: P10Cemented Carbide
a Effects of coolant on the chip control range of a chip breaker

If the cutting speed is the same, the range of chip control differs according to whether coolant is used or not.
Coolant : Dry
0.6
0.5
E
Feed (mm/rev)
Feed (mm/rev)
TECHNICAL DATA
0.5
0.4
0.3
D
C
0.2
A
0.1
1
0.4
0.3
D
C
0.2
A
0.1
4
Depth of Cut (mm)

Workpiece : S45C
Cutting Conditions : vc=100m/min
Q004
Coolant : Wet
(Emulsion)
0.6
Depth of Cut (mm)
Depth of Cut (mm)
EFFECTS OF CUTTING
CONDITIONS FOR TURNING
y EFFECTS OF CUTTING CONDITIONS
Ideal conditions for cutting are short cutting time, long tool life, and high cutting accuracy. In order to obtain these conditions, selection of
efficient cutting conditions and tools, based on work material, hardness, shape and machine capability is necessary.
y CUTTING SPEED
Cutting speed effects tool life greatly. Increasing cutting speed increases cutting temperature and results in shortening tool life. Cutting speed
varies depending on the type and hardness of the work material. Selecting a tool grade suitable for the cutting speed is necessary.
500
400
Workpiece : JIS S45C 180HB

Tool Life Standard : VB = 0.3mm
Feed : 0.3mm/rev
Holder : PCLNR2525M12
Insert : CNMG120408
Dry Cutting
UE6105
MC6025
300
MC6015
AP25N
200
NX2525
MP3025
NX3035
UE6035
VP15TF
100
10
20
30
40
50
60
70
80
90 100
Tool Life (min)
P Class Grade Tool Life
500
Workpiece : JIS SUS304 200HB

Feed : 0.3mm/rev
Insert : CNMG120408-MA
Dry Cutting
400
MC7015
300
200
150
MC7025
US735
US7020
MP7035
100
UTi20T
80
60
10
20
30
40
60
100
Tool Life (min)
M Class Grade Tool Life
300
200
MC5015
UC5115
UE6110
AP25N
UC5105
NX2525
150
100
Workpiece : JIS FC300 180HB

Feed : 0.3mm/rev
Insert : CNMG120408
Dry Cutting
MC5005
400
HTi10
UTi20T
80
60
10
20
30
40
60
100
Tool Life (min)
K Class Grade Tool Life
TECHNICAL DATA
500
a Effects of Cutting Speed

1. Increasing cutting speed by 20% decreases tool life by 50%. Increasing cutting speed by 50% decreases tool life by 80%.
2. Cutting at low cutting speed (20 40m/min) tends to cause chattering. Thus, tool life is shortened.
Q005
TECHNICAL DATA
EFFECTS OF CUTTING
CONDITIONS FOR TURNING
y FEED
When cutting with a general type holder, feed is the distance a holder moves per workpiece revolution. When milling, feed is the
distance a machine table moves per cutter revolution divided by the number of inserts. Thus, it is indicated as feed per tooth. Feed
rate relates to finished surface roughness.
a Effects of Feed
Flank Wear (mm)
1. Decreasing feed rate results in flank wear and shortens

tool life.
2. Increasing feed rate increases cutting temperature and
flank wear. However, effects on the tool life is minimal
compared to cutting speed.
3. Increasing feed rate improves machining efficiency.
0.4
0.3
0.2
0.1
0
0.03
0.06
0.08
0.1
0.2
0.3
0.6
Feed (mm/rev)
Cutting Conditions Workpiece : JIS SNCM431 Grade : STi10T
Insert : 0-0-5-5-35-35-0.3mm
Depth of Cut ap=1.0mm
Cutting Speed vc=200m/min
Cutting Time Tc=10min
Feed and Flank Wear Relationship in Steel Turning
y DEPTH OF CUT
a Effects of Depth of Cut

1. Changing depth of cut doesn't effect tool life greatly.
2. Small depths of cut result in friction when cutting the
hardened layer of a workpiece. Thus tool life is
shortened.
3. When cutting uncut surfaces or cast iron surfaces, the
depth of cut needs to be increased as much as the
machine power allows in order to avoid cutting impure
hard layers with the tip of cutting edge to prevent
chipping and abnormal wear.
Flank Wear (mm)
Depth of cut is determined according to the required stock removal, shape of workpiece, power and rigidity of the machine and tool rigidity.
0.4
0.3
0.2
0.1
0
0.03
0.05
0.1
0.2
0.5
1.0
2.0
3.0
Depth of Cut (mm)

Cutting Conditions Workpiece : JIS SNCM431 Grade : STi10T
Insert : 0-0-5-5-35-35-0.3mm
Feed f=0.20mm/rev
Cutting Speed vc=200m/min
Cutting Time Tc=10min
Depth of Cut and Flank Wear Relationship in Steel Turning
Depth of
Cut
TECHNICAL DATA
Uncut Surface
Roughing of Surface Layer that Includes Uncut Surface
Q006
FUNCTION OF TOOL FEATURES

FOR TURNING
y RAKE ANGLE
Rake angle is cutting edge angle that has a large effect on cutting resistance, chip disposal, cutting temperature and tool life.
200
Positive Insert
50
30
20
10
Negative Rake
Angle
120
100
Depth of Cut : 2mm

Feed : 0.2mm/rev
1200
1000
Depth of Cut : 2mm

500
Feed : 0.2mm/rev
50 100
200
Cutting Conditions
Grade : STi10
Depth of Cut : 1mm Feed : 0.32mm/rev
Workpiece : JIS SK5
-15 -10
a Effects of Rake Angle

1. Increasing rake angle in the positive (+) direction
improves sharpness.
2. Increasing rake angle by 1 in the positive (+)
direction decreases cutting power by about 1%.
3. Increasing rake angle in the positive (+) direction
lowers cutting edge strength and in the negative
(-) direction increases cutting resistance.
-5
10
15
20
25
Cutting Conditions
Workpiece : JIS SK5
Grade : STi10T
Insert : 0-Var-5-5-20-20-0.5mm
Dry Cutting
Rake Angle and Tool Life
Chip Disposal and Rake Angle
Rake Face Mean

Temperature
600
Negative
Insert
Cutting Resistance
Vertical Force
1400
Rake Angle ()
(- )

Depth of Cut : 1mm Feed = 0.32mm/rev
140
Cutting
Temperature
(C)
Tool Life (min)
(+ )
5
gle 1
e An
Rak
6
10
gle
gle e An
e An
Rak
Rak
100
80
Positive Rake
Angle
Vertical Force Cutting Speed

(N)
(m/min)
Tool Life
Standard
VB = 0.4
mm
Effects of Rake Angle on

Cutting Speed, Vertical Force,
and Cutting Temperature
When to Increase Rake Angle

in the Negative (-) Direction
When to Increase Rake Angle

in the Positive (+) Direction
u Hard workpieces.
u When the cutting edge strength is
u Soft workpieces.
u Workpiece is easily machined.
u When the workpiece or the
required such as for uncut

surfaces and interrupted cutting.
machine have poor rigidity.
y FLANK ANGLE
Flank angle prevents friction between flank face and workpiece resulting in smooth feed.
Rake Angle 6
%
Large Flank Angle
D.O.C.
(Same)
Small
Flank Wear
%
Small Flank Angle
D.O.C.
(Same)
Large
Flank Wear
Wear Depth
Flank angle creates a space between tool and workpiece.

Flank angle relates to flank wear.
a Effects of Rake Angle

1. Increasing flank angle decreases flank wear
occurrence.
2. Increasing flank angle lowers cutting edge
strength.
=2
00
0.2
vc =
0.1
vc
0.05
3
Cutting Conditions
re
ctu
Fra
100
$
Flank Angle $
=5
8 10 12
Flank Angle ($)
15
20
Workpiece : JIS SNCM431 (200HB)

Grade : STi20
Insert : 0-6-$-$-20-20-0.5mm
Depth of Cut : 1mm
Feed : 0.32mm/rev Cutting Time : 20min
Flank Angle and Flank Wear Relationship
When to Decrease Flank Angle

u Hard workpieces.
u When cutting edge strength is
required.
vc
TECHNICAL DATA
Wear Depth
Flank Wear (mm)
0.3
When to Increase Flank Angle

u Soft workpieces.
u Workpieces suffer from work
hardening easily.
Q007
TECHNICAL DATA

FOR TURNING
y SIDE CUTTING EDGE ANGLE (LEAD ANGLE)
The side cutting edge angle reduces impact load and effects the amount of feed force, back force and chip thickness.
80
1.1
5B
f = Same
1.04
f = Same
f = Same
60
Workpiece : JIS SCM440

Grade : STi120
Depth of Cut : 3mm
Feed : 0.2mm/rev
Dry Cutting
0.8
kr = 30
kr = 15
Side Cutting Edge Angle and Chip Thickness
B : Chip Width
f : Feed
h : Chip Thickness
kr : Side Cutting
Edge Angle
30
20
10
a Effects of Side Cutting Edge Angle (Lead Angle)
1. At the same feed rate, increasing the side cutting edge angle increases the chip
contact length and decreases chip thickness. As a result, the cutting force is
dispersed on a longer cutting edge and tool life is prolonged. (Refer to the chart.)
2. Increasing the side cutting edge angle increases force a'. Thus, thin, long workpieces
suffer from bending in some cases.
3. Increasing the side cutting edge angle decreases chip control.
4. Increasing the side cutting edge angle decreases the chip thickness and increases
chip width. Thus, breaking chips is difficult.
6
5
u Finishing with small depth of
cut.
u Thin, long workpieces.
u When the machine has poor
rigidity.
4
3
100
u Hard workpieces which produce
150 200
300
Side Cutting Edge and Tool Life
When to Increase Lead Angle
When to Decrease Lead Angle
le 15
Ang
0
dge
ngle
ing E
ge A
Cutt
g Ed
Side ide Cuttin
S
kr = 0
7h
Tool Life (min)
40
0.97
A
A
a'
high cutting temperature.
u When roughing a workpiece
with large diameter.
u When the machine has high
rigidity.
Receive force A.
Force A is divided
into a and a'.
y END CUTTING EDGE ANGLE

The end cutting edge angle avoids interference between the machined
surface and the tool (end cutting edge). Usually 5 15.
End Cutting
Edge Angle
a Effects of End Cutting Edge Angle
TECHNICAL DATA
1. Decreasing the end cutting edge angle increases cutting edge strength,
but it also increases cutting edge temperature.
2. Decreasing the end cutting edge angle increases the back force and
can result in chattering and vibration while machining.
3. Small end cutting edge angle for roughing and large angle for finishing
are recommended.
Side Flank Angle
y CUTTING EDGE INCLINATION

Cutting edge inclination indicates inclination of the rake face. During
heavy cutting, the cutting edge receives an extremely large shock at the
beginning of each cut. Cutting edge inclination keeps the cutting edge
from receiving this shock and prevents fracturing. 3 5 in turning and
10 15 in milling are recommended.
a Effects of Cutting Edge Inclination

1. Negative () cutting edge inclination disposes chips in the workpiece
direction, and positive (+) disposes chips in the opposite direction.
2. Negative () cutting edge inclination increases cutting edge strength,
but it also increases the back force of cutting resistance. Thus,
chattering can easily occur.
Q008
Back Relief Angle
True Rake
Angle
()
Cutting Edge
Inclination
Main Cutting Edge
End Cutting Edge

Angle
Corner Radius
Side Cutting
Edge Angle
EDR
Round Honing
5000
R Honing
C Honing
R Honing
C Honing
VB KT
50
20
Feed Force (N)
500
10
100
0
0.02
0.05
0.1
0.2
0.5
Honing Size (mm)

Grade : P10
Cutting Conditions : vc=200m/min ap=1.5mm
f=0.335mm/rev
Honing Size and Tool Life

Due to Fracturing
0.02
0.05 0.1
0.2
0.5

Grade : P10
f=0.45mm/rev
Honing Size and Tool Life

Due to Wear
Flat Land
1700
1600
1500
1400
1400
900
800
700
600
800
Honing Size (mm)

Back Force (N)
1000
Land Width
Chamfer Honing
100
Tool Life (min)
Tool Life (Number of Impacts)
Honing Width
Honing Angle
Honing Width
Honing and land are cutting edge shapes

that maintain cutting edge strength.
Honing can be round or chamfer type. The
optimal honing width is approximately 1/2 of
the feed.
Land is the narrow flat area on the rake or
flank face.
Principal Force (N)
y HONING AND LAND
700
R Honing
C Honing
600
500
400
0.02
0.05 0.1
0.2
0.5
Honing Size (mm)

Grade : P10
f=0.425mm/rev
Honing Size and Cutting Resistance
a Effects of Honing
When to Decrease Honing Size
When to Increase Honing Size
u When finishing with small depth
u Hard workpieces.
u When the cutting edge strength
of cut and small feed.

u Soft workpieces.
u When the workpiece or the
machine have poor rigidity.
is required such as for uncut

surfaces and interrupted cutting.
rigidity.
TECHNICAL DATA
1. Enlarging the honing increases cutting edge strength, tool life and reduces fracturing.
2. Enlarging the honing increases flank wear occurrence and shortens tool life. Honing size doesn't affect rake wear.
3. Enlarging the honing increases cutting resistance and chattering.
*Cemented carbide, coated diamond, and indexable cermet inserts have round honing as standard.
Q009
TECHNICAL DATA

FOR TURNING
40
Feed
Radius effects the cutting edge strength and

finished surface. In general, a corner radius
2 3 times the feed is recommended.
Depth
of Cut
Theoretical Finished
Surface Roughness
Feed
Finished Surface (!)
y RADIUS
Feed (mm/rev)
0.075
0.106
0.150
0.212
0.300
30
20
10
0.4
0.8
1.2
1.6
2.0
Corner Radius (mm)

Depth
of Cut
Surface Roughness

Grade : P20
Cutting Speed : vc=120m/min ap=0.5mm
2000
1000
0.5
1.0
1.5
2.0
Corner Radius (mm)
Workpiece : JIS SNCM440

(280HB)
Grade : P10
Cutting
Conditions : vc=100m/min
ap=2mm
f=0.335mm/rev
0.2
0.04
0.5
1.0
1.5
2.0
Workpiece : JIS SNCM439

(200HB)
Grade : P10
Cutting
Conditions : vc=140m/min
ap=2mm
f=0.212mm/rev
Tc=10min
Corner Radius Size and Tool Wear
When to Decrease Corner Radius
1. Increasing the corner radius improves the

surface finish.
2. Increasing the corner radius improves cutting
edge strength.
3. Increasing the corner radius too much increases
the cutting resistance and causes chattering.
4. Increasing the corner radius decreases flank and
rake wear.
5. Increasing the corner radius too much results in
poor chip control.
0.08
Corner Radius (mm)
Corner Radius Size and Tool Life Due to Fracturing
a Effects of Corner Radius
Flank Wear
Crater Wear
(Crater Depth)
0.4
Crater Wear Depth (mm)
Flank Wear Width (mm)
Tool Life (Number of Impacts)
Corner Radius and Finished Surface
When to Increase Corner Radius
u Finishing with small depth of cut.

u Thin, long workpieces.
u When the machine has poor
u When the cutting edge strength
is required such as in intrrupted

cutting and uncut surface cutting.
u When roughing a workpiece
with large diameter.
rigidity.
rigidity.
a Corner Radius and Chip Control Range

1.8
0.6
0.2
R1
Feed (mm/rev)
TECHNICAL DATA
0.5
15
D
C
0.4
Workpiece : JIS S45C (180HB)

Insert : TNGG160404R
TNGG160408R
TNGG160412R
(STi10T)
Holder : ETJNR33K16
(Side Cutting Edge angle 3)
B
0.3
A
: 0.4R(TNGG160404R)
0.2
: 0.8R(TNGG160408R)
: 1.2R(TNGG160412R)
0.1
Depth of Cut (mm)
(Note) Please refer to page Q004 for chip shapes (A, B, C, D, E).
Q010
Cutting Speed : vc=100m/min

Dry Cutting
FORMULAE FOR CUTTING POWER

y CUTTING POWER (Pc)
Pc (kW)
: Actual Cutting Power
f (mm/rev) : Feed per Revolution
Kc (MPa)
: Specific Cutting Force
(kW)
(Problem) What is the cutting power required for machining mild steel
at cutting speed 120m/min with depth of cut 3mm and feed
0.2mm/rev (Machine coefficient 80%) ?
(Answer) Substitute the specific cutting force

Kc=3100MPa into the formula.
Pc =
a Kc
Tensile Strength(MPa)
and Hardness
Work Material
Mild Steel
Medium Steel
Hard Steel
Tool Steel
Tool Steel
Chrome Manganese Steel
Chrome Molybdenum Steel
Nickel Chrome Molybdenum Steel
Hard Cast Iron
Meehanite Cast Iron
Grey Cast Iron
520
620
720
670
770
770
630
730
600
900
352HB
46HRC
360
200HB
0.1 (mm/rev)
3610
3080
4050
3040
3150
3830
4510
4500
3610
3070
3310
3190
2300
2110
y CUTTING SPEED (vc)
vc =
ap (mm) : Depth of Cut

vc (m/min) : Cutting Speed
( : (Machine Coefficient)
)Dm n
1000
(m/min)
Specific Cutting Force Kc (MPa)

0.2 (mm/rev)
0.3 (mm/rev)
0.4 (mm/rev)
3100
2720
2500
2700
2570
2450
3600
3250
2950
2800
2630
2500
2850
2620
2450
3250
2900
2650
3900
3240
2900
3900
3400
3150
3200
2880
2700
2650
2350
2200
2900
2580
2400
2800
2600
2450
1930
1730
1600
1800
1600
1400
vc
Dm
)
n
(m/min)
(mm)
(3.14)
(min-1)
: Cutting Speed
: Workpiece Diameter
: Pi
: Main Axis Spindle Speed
-1
700min and external diameter is & 50 ?
f=
l
n
(mm/rev)

I (mm/min) : Cutting Length per Min.
n (min-1)
(Problem) What is the feed per revolution when main axis spindle speed is
500min-1 and cutting length per minute is 120mm/min ?
(Answer) Substitute n=500, I=120 into the formula.
(Answer) Substitute ) = 3.14, Dm = 50, n = 700 into the formula.
) Dmn
=
1000
f=
3.1450700
= 110m/min
1000
l
120
=
= 0.24mm/rev
n
500
The answer is 0.24mm/rev.
Cutting speed is 110m/min.
Dm
y CUTTING TIME (Tc)
Tc=
Im
l
(min)
0.6 (mm/rev)
2280
2300
2640
2400
2340
2400
2630
2850
2500
1980
2200
2270
1450
1330
y FEED ( f )
Divide by 1000 to change to m from mm.

*(Problem)
What is the cutting speed when main axis spindle speed is
vc =
30.21203100
= 4.65 (kW)
601030.8
y THEORETICAL FINISHED SURFACE ROUGHNESS (h)

Tc (min)
: Cutting Time
Im (mm)
: Workpiece Length
I (mm/min): Cutting Length per Min.
h=
f2
8RE
1000(!m)
h (!m)
: Finished Surface Roughness
RE(mm)
: Insert Corner Radius
(Problem) What is the cutting time when 100mm workpiece is machined at

1000min-1 with feed = 0.2mm/rev ?
(Problem) What is the theoretical finished surface roughness when the insert
corner radius is 0.8mm and feed is 0.2mm/rev ?
(Answer) First, calculate the cutting length per min. from the feed and
spindle speed.
(Answer) Substitute f=0.2mm/rev, RE=0.8 into the formula.
h=
I = fn = 0.21000 = 200mm/min
0.22
1000 = 6.25 !m
80.8
The theoretical finished surface roughness is 6!m.
Substitute the answer above into the formula.
Im
100
Tc =
=
= 0.5 min
l
200
TECHNICAL DATA
ap f vc Kc
60103(
Pc =
Feed
Feed
0.5 x 60=30 (sec.) The answer is 30 sec.

Depth
of Cut
Surface Roughness
Depth
of Cut
Surface Roughness
Q011
TECHNICAL DATA
TROUBLE SHOOTING FOR FACE MILLING
Deterioration of Surface Finish

Burr, Workpiece Chipping
Chip Control
TECHNICAL DATA
Q012
Poor finished
surface
Welding occurs
Not parallel
or irregular
surface
Poor chip
dispersal,
chip jamming
and chip
packing
a
a
a
a
a
a
Dry
a
Wet
a
a
Wet
a
a
a
a
a
a
Tool clearance
a
a
Low sharpness
a
a
Low sharpness
A small
corner angle
a
a
Chattering
Welding occurs
Chip thickness
is too thin
Cutter diameter
is too small
Poor chip
disposal
A large
corner angle
Improper
cutting conditions
Workpiece
edge
chipping
Wet
Large back force
Burrs,
chipping
Workpiece
bending
Chip thickness
is too large
Cutter diameter
is too large
Poor run-out
accuracy
Chattering
Lack of rigidity
Improper
cutting conditions

backlash
Improve run-out accuracy
Use of a wiper insert
Down
Wider chip pocket
Up
Smaller Larger Number of teeth
Cutter diameter
Honing strengthens
the cutting edge
Corner angle
Rake
Engage angle
Up

Determine dry or
wet cutting
Depth of cut
Feed
Cutting speed

adhesion resistance
Down
Coolant
Machine,
Decrease overhang
Chipping or
fracturing of
cutting edge
Up
Style and Design

of the Tool

Insert wear
quickly
generated
Improper
tool grade
Improper cutting
edge geometry
Improper
cutting speed
Improper
tool grade
Improper
cutting conditions
Lack of cutting
edge strength.
Thermal crack
occurs
Build-up
edge occurs
Cutting
Conditions
Cutter rigidity
Factors
Trouble
Solution
Insert Grade
Selection
a
a
a
Wet

FOR FACE MILLING
y FUNCTION OF EACH CUTTING EDGE ANGLE IN FACE MILLING
Type of Angle
Axial Rake Angle
(GAMP)
Lead
Angle
(KAPR)
Wiper Insert
Cutting Edge
Inclination
(I)
True Rake Angle (T)
Effect
Determines
Negative :
Excellent chip disposal.
Determines
Small : Thin chips and small

cutting impact.
Large back force.
Positive (large) :
Excellent machinability.
Minimal welding.
Negative (large) :
Poor machinability.
Strong cutting edge.
Positive (large) :
Excellent chip disposal.
Low cutting edge strength.
Radial Rake Angle GAMF sharpness.

KAPR chip
thickness.
True Rake Angle
Determines
actual
sharpness.
Cutting Edge
Inclination
Determines
chip disposal
direction.
Radial Rake Angle (GAMF)
Each Cutting Edge Angle in Face Milling
Function
Determines chip Positive :

Axial Rake Angle GAMP disposal direction. Excellent machinability.
Lead Angle
Main Cutting Edge
Symbol
y STANDARD INSERTS
a Positive and Negative Rake Angle
Negative
Rake Angle
Neutral
Rake Angle
(-)
a Standard Cutting Edge Shape

(+) Axial Rake Angle
(-) Axial Rake Angle
Radial Rake Angle
Radial Rake Angle
(+) Axial Rake Angle
Positive
Rake Angle
(+)
Standard Cutting
Edge Combinations
(+)
Insert shape whose cutting edge

precedes is a positive rake angle.
Insert shape whose cutting edge
follows is a negative rake angle.
(-)
Radial Rake Angle

(-)
Double Positive
(DP Edge Type)
Double Negative
(DN Edge Type)
Axial Rake Angle (GAMP)
Positive ( + )
Negative ( )
Positive ( + )
Radial Rake Angle (GAMF)
Positive ( + )
Negative ( )
Negative ( )
Positive Insert (One Sided Use) Negative Insert (Double Sided Use) Positive Insert (One Sided Use)
Insert Used
Work Material
Negative/Positive
(NP Edge Type)
Steel
Cast Iron
Aluminium Alloy
Difficult-to-Cut Material
3000
2500
2000
Lead Angle : 90
Lead Angle : 75
Lead Angle : 45
Principal
Force
Principal
Force
Principal
Force
90
1500
1000
500
0
-500
Feed Force
Feed Force
Lead Angle
Back force is in the minus

direction. Lifts the workpiece when
workpiece clamp rigidity is low.
Feed Force
Lead Angle 90
0.1 0.2 0.3
Back Force
fz (mm/t.)
Back Force
0.1 0.2 0.3

fz (mm/t.)
Back Force
0.1 0.2 0.3

fz (mm/t.)
Workpiece : JIS SCM440 (281HB)

Tool : 125mm Single Insert
Cutting Conditions : vc=125.6m/min ap=4mm ae=110mm
Lead Angle
75
Lead angle 75is recommended for

face milling of workpieces with low
rigidity such as thin workpieces.
Lead Angle 75
Cutting Resistance Comparison between

Different Insert Shapes
Principal Force
Back Force
Lead Angle
ae
Feed Force
ap
45
The largest back force.

Bends thin workpieces and lowers
cutting accuracy.
Prevents workpiece edge chipping
when cast iron cutting.
Lead Angle 45
TECHNICAL DATA
Cutting Resistance (N)
y LEAD ANGLE (KAPR) AND CUTTING CHARACTERISTICS
Table Feed
Three Cutting Resistance Forces in Milling
force : Force is in the opposite direction of face milling rotation.

* Principal
Back force : Force that pushes in the axial direction.
* Feed force : Force is in the feed direction and is caused by table feed.
*
Q013
TECHNICAL DATA

FOR FACE MILLING
y APPROACH ANGLE AND THE TOOL LIFE
a Approach Angle and Chip Thickness

When the depth of cut and feed per tooth, fz, are fixed, the smaller the corner angle (KAPR) is, then the thinner the chip thickness (h) becomes (for a 45
KAPR, it is approx. 75% that of a 90 KAPR). This can be seen in below. Therefore as the KAPR increases, the cutting resistance decreases resulting in
longer tool life. Note however, if the chip thickness is too large then the cutting resistance can increase leading to vibrations and shortened tool life.
KAPR:90
KAPR:45
KAPR:75
h=fz
h=0.96fz
h=0.75fz
90
75
45
fz
fz
fz
Effects on chip thickness due to the variation of lead angles
a Approach Angle and Face Wear

Below shows wear patterns for different lead angles. When comparing crater wear for 90 and 45 lead angles, it can be clearly seen
that the ctater wear for 90 lead angle is larger.
Lead Angle 90
Lead Angle 75
Lead Angle 45
vc=100m/min
Tc=69min
vc=125m/min
Tc=55min
Workpiece :
Tools :
Insert :
vc=160m/min
Tc=31min
SNCM439 287HB
DC=125mm
M20Cemented Carbide
ap=3.0mm
ae=110mm
fz=0.2mm/t.
Dry Cutting
y UP AND DOWN CUT (CLIMB) MILLING

When choosing a method to machine, up cutting or down cut milling (climb milling) is decided by the conditions of the machine tool, the
milling cutter and the application. However, it is said that in terms of tool life, down cut (climb) milling is more advantageous.
TECHNICAL DATA
Up Cut
Tool rotation
Milling cutter inserts
Portion machined
Workpiece
movement
direction
Tool rotation
Milling cutter inserts

Portion machined
Q014
Down Cut
Workpiece
movement
direction
y FINISHED SURFACE
a Cutting Edge Run-out Accuracy
Cutting edge run-out accuracy of indexable inserts on the cutter body greatly affects
the surface finish and tool life.
Minor Cutting Edge
Large
Peripheral
Cutting Edge
Chipping Due to Vibration
Poor Finished Surface
Rapid Wear Growth
Run-out
Small
Good Finished Surface
Shorten Tool Life
Stable Tool Life
Cutting Edge Run-out and

Accuracy in Face Milling
2 3 4 5 6 1
f
Cutting Edge No.

fz
fz : Feed per Tooth

f : Feed per Revolution
Sub Cutting Edge Run-out

and Finished Surface
*1
Actual Problems
Countermeasure
Cutting edge run-out.

Sub cutting edge
inclination.
Milling cutter body
accuracy.
Spare parts accuracy.
Welding, vibration,
chattering.
Wiper Insert
0.1mm
Table Feed
Since Mitsubishi Materials' normal sub cutting edge width is 1.4mm, and the sub
cutting edges are set parallel to the face of a milling cutter, theoretically the finished
surface accuracy should be maintained even if run-out accuracy is low.
0.03
D.O.C
a Improve Finished Surface Roughness
Wiper Insert
Standard Insert
Machine a surface
that has already
been per-machined
in order to produce Replace one or two normal inserts with
wiper inserts.
smooth finished
surface.
Wiper inserts be set to protrude by
0.03 0.1mm from the standard inserts.
depends on the cutting edge and insert

*1.Value
combination.
a How to Set a Wiper Insert
Locator
Body
Locator
(a) One Corner Type
(b) Two Corner Type
Replace normal insert.
Replace normal insert.
Body
Locator
(c) Two Corner Type

Use locator for
wiper insert.
TECHNICAL DATA
Body
Sub cutting edge length has to be longer than

the feed per revolution.
Too long sub cutting edge causes chattering.
When the cutter diameter is large and feed per
revolution is longer than the sub cutting edge of
the wiper insert, use two or three wiper inserts.
When using more than 1 wiper inserts, eliminate
run-out of wiper inserts.
Use a high hardness grade (high wear
resistance) for wiper inserts.
Q015
TECHNICAL DATA
FORMULAE FOR FACE MILLING

vc =
) DC n
1000
(m/min)
*Divide by 1000 to change to m from mm.

n

) (3.14) : Pi
DC (mm) : Cutter Diameter

n (min-1) : Main Axis Spindle Speed
(Problem) What is the cutting speed when main axis spindle speed is
350min-1 and the cutter diameter is &125 ?
(Answer) Substitute )=3.14, DC=125, n=350 into the formula.
vc =
)DC n
3.14125350
=
= 137.4 m/min
1000
1000
The cutting speed is 137.4m/min.
DC
y FEED PER TOOTH (fz)
fz =
vf
(mm/tooth)
z n
Feed
Direction
Wiper Edge Angle

Tooth Mark
Feed per Tooth (fz)
fz (mm/tooth) : Feed per Tooth

z : Insert Number
vf (mm/min) : Table Feed per Min.
n (min-1)
: Main Axis Spindle Speed (Feed per Revolution f = z x fz)
(Problem) What is the feed per tooth when the main axis spindle speed is
500min-1, number of insert is 10, and table feed is 500mm/min ?
(Answer) Substitute the above figures into the formula.
vf
500
=
= 0.1 mm/tooth
zn
10500
The answer is 0.1mm/tooth.
fz =
y TABLE FEED (vf)
vf = fz z n (mm/min)

z : Insert Number
fz (mm/tooth) : Feed per Tooth
n (min-1)
(Problem) What is the table feed when feed per tooth is 0.1mm/tooth, number of
insert is 10, and main axis spindle speed is 500min-1?
(Answer) Substitute the above figures into the formula.
vf = fzzn = 0.110500 = 500mm/min
The table feed is 500mm/min.
y CUTTING TIME (Tc)
TECHNICAL DATA
Tc =
L
vf
(min)
DC
l
L
Tc (min)
: Cutting Time
L (mm)
: Total Table Feed Length (Workpiece Length: (l)+Cutter Diameter : (DC))
(Problem) What is the cutting time required for finishing 100mm width and 300mm
length surface of a cast iron (JIS FC200) block when the cutter
diameter is &200mm, the number of inserts is 16, the cutting speed is
125m/min, and feed per tooth is 0.25mm. (spindle speed is 200min-1)
(Answer) Calculate table feed per min vf=0.2516200=800mm/min
Calculate total table feed length. L=300+200=500mm
Substitute the above answers into the formula.
500
Tc =
= 0.625 (min)
800
0.62560=37.5 (sec). The answer is 37.5 sec.
Q016
y CUTTING POWER (Pc)
ap ae vf Kc
60106(
Pc =
Pc (kW)
ae (mm)
Kc (MPa)
: Actual Cutting Power

: Cutting Width
: Specific Cutting Force
ap (mm)
: Depth of Cut
( : (Machine Coefficient)
(Problem) What is the cutting power required for

(Answer) First, calculate the spindle speed in order to obtain feed per tooth.
milling tool steel at a cutting speed of
1000vc
100080
n=
=
= 101.91min-1
) DC
3.14250
80m/min. With depth of cut 2mm, cutting
vf
280
width 80mm, and table feed 280mm/min
Feed per Tooth fz =
=
= 0.228mm/tooth
zn
12101.9
&
by 250 cutter with 12 inserts. Machine
Substitute the specific cutting force into the formula.
coefficient 80%.
Pc =
2802801800
601060.8
= 1.68 kW
a Kc
0.1mm/tooth
Mild Steel
520
2200
1950
1820
1700
1580
Medium Steel
620
1980
1800
1730
1600
1570
Hard Steel
720
2520
2200
2040
1850
1740
Tool Steel
670
1980
1800
1730
1700
1600
Tool Steel
770
2030
1800
1750
1700
1580
770
2300
2000
1880
1750
1660
630
2750
2300
2060
1800
1780
730
2540
2250
2140
2000
1800
600
2180
2000
1860
1800
1670
940
2000
1800
1680
1600
1500
352HB
2100
1900
1760
1700
1530
155HB
2030
1970
1900
1770
1710
520
2800
2500
2320
2200
2040
46HRC
3000
2700
2500
2400
2200
360
2180
2000
1750
1600
1470
Cast Iron
Hard Cast Iron
Meehanite Cast Iron
0.6mm/tooth
200HB
1750
1400
1240
1050
970
Brass
500
1150
950
800
700
630
Light Alloy (Al-Mg)
160
580
480
400
350
320
Light Alloy (Al-Si)
200
700
600
490
450
390
Light Alloy (Al-Zn-Mg-Cu)
570
880
840
840
810
720
Grey Cast Iron
TECHNICAL DATA
Specific Cutting Force Kc (MPa)

0.2mm/tooth
0.3mm/tooth
0.4mm/tooth
Tensile Strength (MPa)

and Hardness
Work Material
Q017
TECHNICAL DATA
TROUBLE SHOOTING FOR END MILLING
Large peripheral
cutting edge
wear
Severe
chipping
Breakage
during cutting
Non-coated end
mill is used
A small number
of cutting edges
Improper
cutting conditions
Up cut milling
is used
Improper
cutting conditions
Fragile cutting
edge
Insufficient
clamping force
Low clamping
rigidity
Improper
cutting conditions
Low end mill
rigidity
Overhang longer
than necessary
Q018
Poor surface
finish on walls
Poor surface
finish on faces
Out of
vertical
Burrs, Chipping, etc.
Burr or
chipping
occurs
Quick bur
formation
Chip packing
Lack of chip pocket
Increase tool installation

accuracy
Increase spindle collet
run-out accuracy
Collet inspection and
exchange
Increase chuck clamping
power
Increase work clamping
rigidity
Shorten tool overhang
Wider chip pocket
Tool diameter
Concavity angle of
end cutting edge
Insert number
a
a
a
a
a
a
a
a
a
a
a
Wet
a
a
a
a
a
a
Large helix angle
Improper
cutting conditions
Metal removal
too large
Helix angle
Large pick feed
Notch wear
Smaller
Down
Cut
The end cutting edge does

not have a concave angle
Large cutting
edge wear
Improper
cutting conditions
Lack of end mill
rigidty
Improper
cutting conditions
Low clamping
rigidity
Improper
cutting conditions
Down
Chip packing.
Poor dimensional
accuracy
Poor Chip
Dispersal
TECHNICAL DATA
Deterioration of Surface Finish
Vibration
during cutting
Larger
Chip jamming
Improper
cutting conditions
Low end mill
rigidity
Low clamping
rigidity
Large cutting
edge wear
Improper
cutting conditions
Up
Cutter rigidity
Down
Down
Increase coolant
quantity
Determine dry or
wet cutting
Up
Use air blow
Pick feed
Depth of cut
Feed
Coolant
Down cut
Factors
Coated tool
Trouble
Style and Design

Machine,
of the Tool
Cutting Conditions
Cutting speed
Solution
Insert Grade
Selection
a
a
a
a
a
a
a
END MILL TERMINOLOGY

y END MILL TERMINOLOGY
Cutter-sweep
Neck
Flute
Shank
Diameter
Shank diameter
Length of cut
Overall length
Corner
Land width (Groove width)
Concavity angle of end cutting edge
End cutting edge
Peripheral cutting edge
Primary clearance land (Relief width)

End gash
Primary clearance angle

Secondary
clearance angle
Axial rake angle

Helix angle
Radial rake angle

Axial primary relief angle
Axial secondary clearance angle
y COMPARISON OF SECTIONAL SHAPE AREA OF CHIP POCKET
3-flutes
45%
4-flutes
40%
6-flutes
20%
y CHARACTERISTICS AND APPLICATIONS OF DIFFERENT-NUMBER-OF-FLUTE END MILLS

6-flutes
Advantage
4-flutes
Chip disposability is
excellent.
Suitable for sinking.
High rigidity
High rigidity.
Superior cutting edge
durability.
Fault
3-flutes
Chip disposability is excellent.

Suitable for sinking.
Low cutting resistance.
Low rigidity
Diameter is not easily

measured.
Chip disposability is poor.
Chip disposability is poor.
Slotting, side milling,

sinking etc.
Wide range of use.
Slotting, side milling

Heavy cutting, finishing
Shallow slotting, side milling

Finishing
High Hardness Material

Shallow slotting, side milling
Usage
Feature
2-flutes
TECHNICAL DATA
2-flutes
50%
Q019
TECHNICAL DATA
TYPES AND SHAPES OF END MILL

y Peripheral Cutting Edge
Kind
Shape
Feature
Ordinary Flute
Ordinary flute type is most generally used for the slotting, side milling,
and the shoulder milling, etc. Can be used for roughing, semi-finishing,
and the finishing.
Tapered Flute
A tapered fute is used for milling mould drafts and angled faces.
Because a roughing tooth has a wave-like form and produces small

chips. Cutting resistance is low, and is suitable for roughing. Not
suitable for finishing. The tooth face is re-grindable.
Roughing Flute
A corner radius cutter is shown. An infinite range of form cutters can

be produced.
Formed Flute
y End Cutting Edge

Kind
Shape
Feature
Square End
(Centre With Hole)
This is generally used for slotting, side milling, and shoulder milling.
Sinking is not possible. Grinding is center supported, making
re-grinding accurate.
Square End
(Centre Cut)
It is generally used for slotting, side milling, and shoulder milling.

Vertical cutting can be performed. Re-grinding is possible.
Ball End
Suitable for profile machining and pick feed milling.
End Radius
For corner radius milling and contouring. Efficient small corner radius
milling due to large diameter and small corner radius.
y Shank And Neck Parts
TECHNICAL DATA
Kind
Q020
Shape
Feature
Standard
(Straight Shank)
For general use.
Long Shank
For deep slotting and has a long shank, so that adjustment of the
overhang is possible.
Long Neck
For deep slotting and small diameter end mills, also suitable for
boring.
Taper Neck
For best performance in deep slotting and on mould drafts.
PITCH SELECTION OF PICK FEED

y PICK FEED MILLING (CONTOURING) WITH BALL NOSE END MILLS AND END MILLS WITH CORNER RADIUS
End mill
h= R
1 cos
sin-1(
P
2R
R
R : Radius of Ball Nose(PRFRAD), Corner Radius(RE)
P : Pick Feed
P
h : Cusp Height
y CORNER R OF END MILLS AND CUSP HEIGHT BY PICK FEED

P
Unit : mm
Pitch of Pick Feed (P)

0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0.5
0.003
0.010
0.023
0.042
0.067
0.100
0.001
0.005
0.011
0.020
0.032
0.046
0.063
0.083
0.107
1.5
0.001
0.003
0.008
0.013
0.021
0.030
0.041
0.054
0.069
0.086
0.001
0.003
0.006
0.010
0.016
0.023
0.031
0.040
0.051
0.064
2.5
0.001
0.002
0.005
0.008
0.013
0.018
0.025
0.032
0.041
0.051
0.002
0.004
0.007
0.010
0.015
0.020
0.027
0.034
0.042
0.001
0.003
0.005
0.008
0.011
0.015
0.020
0.025
0.031
0.001
0.002
0.004
0.006
0.009
0.012
0.016
0.020
0.025
0.001
0.002
0.003
0.005
0.008
0.010
0.013
0.017
0.021
0.001
0.003
0.004
0.006
0.008
0.010
0.013
0.016
10
0.001
0.002
0.003
0.005
0.006
0.008
0.010
0.013
12.5
0.001
0.002
0.003
0.004
0.005
0.006
0.008
0.010
Pitch of Pick Feed (P)

1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
0.5
1.5
0.104
0.077
0.092
0.109
2.5
0.061
0.073
0.086
0.100
0.051
0.061
0.071
0.083
0.095
0.109
0.038
0.045
0.053
0.062
0.071
0.081
0.091
0.103
0.030
0.036
0.042
0.049
0.057
0.064
0.073
0.082
0.091
0.101
0.025
0.030
0.035
0.041
0.047
0.054
0.061
0.068
0.076
0.084
0.019
0.023
0.026
0.031
0.035
0.040
0.045
0.051
0.057
0.063
10
0.015
0.018
0.021
0.025
0.028
0.032
0.036
0.041
0.045
0.050
12.5
0.012
0.014
0.017
0.020
0.023
0.026
0.029
0.032
0.036
0.040
TECHNICAL DATA
Q021
TECHNICAL DATA
Drill breakage
Large wear at the

peripheral cutting
edge and along
the land
Chipping of
the peripheral
cutting edge
Chisel edge
chipping
Q022
Deterioration of Hole Accuracy

Poor Chip Dispersal Burrs
TECHNICAL DATA
Hole diameter
increases
Hole diameter
becomes
smaller
Poor
straightness
Poor hole positioning

accuracy, roundness
and surface finish
Burrs at the
hole exit
Long chips
Chip
jamming
Lack of drill
rigidity
Improper
cutting conditions
Large deflection
of the tool holder
Workpiece face
is inclined
Improper
cutting conditions
Reduce machine backlash and

increase rigidity
Increase work clamping rigidity
Flat workpiece face
a
a
a
a
a
a
Poor run-out
accuracy
Improper
cutting conditions
Large deflection
of the tool holder
chattering,
vibration
The chisel edge
width is too wide
a
a
a
a
Poor entry
Chattering,
vibration
Lack of drill
rigidity
Improper drill
geometry
a
a
An increase in
temperature at the
cutting point
a
a
a
a
a
a
a
Poor entry
Improper
cutting conditions
Large deflection
of the tool holder
Improper drill
geometry
Improper
cutting conditions
Improper
cutting conditions
Poor chip
disposal
Improper
cutting conditions
Poor chip
disposal
Machine,
Change to a drill with X type
thinning
Increase tool installation
accuracy
Use internal coolant type drill
Decrease lip height
Down
Shorten flute length
Core thickness
Up
An increase in
temperature at the
cutting point
Improper
cutting conditions
Improper drill
geometry
Lack of drill
rigidity
Large deflection
of the tool holder
Poor guiding
properties
Lack of drill
rigidity
Chisel width
Increase coolant
pressure
Increase volume
Increase oil ratio
Increase accuracy of
prep-hole and depth
Coolant
Step feed
Down
Lower feed when breaking

through
Up
Factors
Lower feed at initial cutting
Feed
Cutting speed
Solution
Honing width
Style and Design

of the Tool
Cutting Conditions
Trouble
FOR DRILLING
Shorten tool overhang
TROUBLE SHOOTING
a
a
a
a
a
a
a
DRILL WEAR AND

CUTTING EDGE DAMAGE
y DRILL WEAR CONDITION
W
e
The table below shows a simple drawing depicting the wear of a drills cutting edge. The generation and the amount of wear differ
according to the workpiece materials and cutting conditions used. But generally, the peripheral wear is largest and determines a drill
tool life. When regrinding, the flank wear at the point needs to be ground away completely. Therefore, if there is large wear more
material needs to be ground away to renew the cutting edge.
We : Chisel edge wear width
Wf
Wf
: Flank Wear (The middle of the cutting edge)
Wo : Outer corner wear width
Wo
Wm'
Wm
Wm : Margin wear width

Wm' : Margin wear width (Leading edge)
y CUTTING EDGE DAMAGE

When drilling, the cutting edge of the drill can suffer from chipping, fracture and abnormal damage. In such cases, it is important to take
a closer look at the damage, investigate the cause and take countermeasures.
Cutting edge damage

TECHNICAL DATA
Q023
TECHNICAL DATA
DRILL TERMINOLOGY
AND CUTTING CHARACTERISTICS
y NAMES OF EACH PART OF A DRILL
Straight shank with tang
Height of point
Clearance angle
Body
Lead
Neck
Taper shank
Tang
Helix angle
Drill
diameter
Flank
Functional length
Outer corner
Central axis
Point angle
Shank length
Flute length
Overall length
Neck length
Margin width
Margin
Depth of body clearance

Body clearance
Flute
Flute width
Chisel edge angle

Cutting edge
Land width
y SHAPE SPECIFICATION AND CUTTING CHARACTERISTICS
Helix Angle
Is the inclination of the flute with respect to the axial direction of a drill, which corresponds to the rake angle of a
bit. The rake angle of a drill differs according to the position of the cutting edge, and it decreases greatly as the
circumference approaches the centre.The chisel edge has a negative rake angle, crushing the work.
High-hardness material Small
TECHNICAL DATA
Large
Soft material (Aluminium, etc.)
Flute Length
It is determined by depth of hole, bush length, and regrinding allowance. Since the influence on the tool life is
great, it is necessary to minimize it as much as possible.
Point Angle
In general, the angle is 118 which is set differently to various applications.

Soft material with good machinability Small
Point angle
Large
Web Thickness
Q024
Rake angle
Margin
It is an important element that determines the rigidity and chip raking performance of a drill. The web thickness is
set according to applications.
Large cutting resistance
Small cutting resistance
High rigidity
Low rigidity
Thin
Web thickness
Thick
Poor chip raking performance
Good chip raking performance
High-hardness material,
Machinable material
cross hole drilling, etc.
The tip determines the drill diameter and functions as a drill guide during drilling. The margin width is determined
in consideration of friction during hole drilled.
Poor guiding performance Small
Diameter Back Taper
For hard material and

high-efficiency machining
Margin width
Large
Good guiding performance
To reduce friction with the inside of the drilled hole, the portion from the tip to the shank is tapered slightly. The
degree is usually represented by the quantity of reduction in the diameter with respect to the flute length, which is
approx. 0.04 0.1mm. It is set at a larger value for high-efficiency drills and the work material that allows drilled
holes.
y CUTTING EDGE GEOMETRY AND ITS INFLUENCE

As shown in the table below, it is possible to select the most suitable cutting edge geometry for different applications. If the most
suitable cutting edge geometry is selected then higher machining efficiency and higher hole accuracy can be obtained.
a Cutting Edge Shapes
Grinding name
Shape
Features and effect
Application
The flank is conical and the clearance angle

increases toward the centre of the drill.
General Use
The flank is flat.

Easy grinding.
Mainly for small diameter drills.
As there is no chisel edge, the results are high

centripetal force and small hole oversize.
Requires a special grinding machine.
Surface grinding of three sides.
For drilling operations that

require high hole accuracy and
positioning accuracy.
To increase the clearance angle near the centre

of the drill, conical grinding combined with
irregular helix.
S type chisel edge with high centripetal force and
machining accuracy.
For drilling that requires high

accuracy.
The cutting edge is ground radial with the aim of

dispersing load.
High machining accuracy and finished surface
roughness.
For through holes, small burrs on the base.
Requires a special grinding machine.
Cast Iron, Aluminium Alloy

For cast iron plates.
Steel
This geometry has two-stage point angle for

better concentricity and a reduction in shock
when exiting the workpiece.
For thin sheet drilling.
Conical
Flat
Three flank
angles
Spiral point
Radial lip
Centre Point
drill
y WEB THINNING
Shape
X type
Features
The thrust load substantially

reduces, and the bite
performance improves. This
is effective when the web is
thick.
Major
General drilling and deep
Applications hole drilling.
XR type
S type
N type
The initial performance is

slightly inferior to that of the
X type, but the cutting edge
is hard and the applicable
range of work is wide.
Popular design, easy cutting

type.
Effective when the web is

comparatively thick.
Long life. General drilling and

stainless steel drilling.
General drilling for steel, cast

iron, and non-ferrous metal.
Deep hole drilling.
TECHNICAL DATA
The rake angle of the cutting edge of a drill reduces toward the centre, and it changes into a negative angle at the chisel edge. During drilling,
the centre of a drill crushes the work, generating 50 70% of the cutting resistance. Web thinning is very effective for reduction in the cutting
resistance of a drill, early removal of cut chips at the chisel edge, and better initial bite.
Q025
TECHNICAL DATA
DRILL TERMINOLOGY
AND CUTTING CHARACTERISTICS
y DRILLING CHIPS
Types of Chips
Conical Spiral
Shape
Features and Ease of Raking
Fan-shaped chips cut by the cutting edge are curved by the flute. Chips of this type
are produced when the feeding rate of ductile material is small. If the chip breaks
after several turns, the chip raking performance is satisfactory.
The generated chip comes out without coiling. It will easily coil around the drill.
Long Pitch
Fan
TECHNICAL DATA
Segment
Q026
This is a chip broken by the restraint caused by the drill flute and the wall of a drilled
hole. It is generated when the feed rate is high.
A conical spiral chip that is broken before the chip grows into the long-pitch shape by
the restraint caused by the wall of the drilled hole due to the insufficiency of ductility.
Excellent chip disposal and chip discharge.
Zigzag
A chip that is buckled and folded because of the shape of flute and the characteristics
of the material. It easily causes chip packing at the flute.
Needle
Chips broken by vibration or broken when brittle material is curled with a small radius.
The raking performance is satisfactory, but these chips can pack closely creating.
FORMULAE FOR DRILLING

vc =
) DC n
(m/min)
1000
*Divide by 1,000 to changen to m from mm.

) (3.14)
: Pi
DC (mm) : Drill Diameter

n (min-1) : Main Axis Spindle Speed
(Problem) What is the cutting speed when main axis spindle speed is 1350min-1
and drill diameter is 12mm ?
(Answer) Substitute )=3.14, DC=12, n=1350 into the formula
) DCn
3.14121350
=
= 50.9m/min
1000
1000
The cutting speed is 50.9m/min.
vc =
DC
y FEED OF THE MAIN SPINDLE (vf)

vf (mm/min) : Feed Speed of the Main Spindle (Z axis)
fr (mm/rev) : Feed per Revolution
n (min-1)
vf = fr n(mm/min)
vf
(Problem) What is the spindle feed (vf) when the feed per revolution is 0.2mm/rev
and main axis spindle speed is 1350min-1 ?
(Answer) Substitute f=0.2, n=1350 into the formula
vf = fn = 0.21350 = 270mm/min
The spindle feed is 270mm/min.
y DRILLING TIME (Tc)
Id i
n fr
n
(Problem) What is the drilling time required for drilling a 30mm

length hole in alloy steel (JIS SCM440) at a cutting
speed of 50m/min and a feed 0.15mm/rev ?
501000
= 1061.57min-1
153.14
301
Tc =
= 0.188
1061.570.15
(Answer) Spindle Speed n =
= 0.18860i11.3 sec
ld
TECHNICAL DATA
Tc =
Tc (min)
: Drilling Time
n (min-1) : Spindle Speed
ld (mm)
: Hole Depth
fr (mm/rev) : Feed per Revolution
i
: Number of Holes
Q027
TECHNICAL DATA
METALLIC MATERIALS CROSS

REFERENCE LIST
y CARBON STEEL
Japan
JIS
Germany
W-nr.
DIN
U.K.
BS
EN
STKM 12A
1.0038
STKM 12C
1.0401
1.0402
RSt.37-2
4360 40 C
C15
C22
080M15
050A20
SUM22
9SMn28
9SMnPb28
10SPb20
9SMn36
9SMnPb36
Ck15
Ck25
StE380
C35
C45
35S20
40Mn4
36Mn5
28Mn6
Cf35
Ck45
Cf53
C55
C60
Ck55
Ck60
Ck101
C105W1
C105W1
1.0715
SUM22L
1.0718
1.0722
1.0736
1.0737
S15C
1.1141
S25C
1.1158
1.8900
1.0501
1.0503
1.0726
1.1157
SMn438(H) 1.1167
SCMn1
1.1170
S35C
1.1183
S45C
1.1191
S50C
1.1213
1.0535
1.0601
S55C
1.1203
S58C
1.1221
1.1274
SK3
1.1545
SUP4
1.1545
France
Italy
Spain
Sweden
USA
China
AFNOR
UNI
UNE
SS
AISI/SAE
GB
E 24-2 Ne
2C
CC12
CC20
C15, C16
C20, C21
230M07
1A
S250
CF9SMn28
240M07
080M15
4360 55 E
060A35
080M46
212M36
150M36
150M28
060A35
080M46
060A52
070M55
080A62
070M55
080A62
060A96
BW1A
BW2
1B
32C
8M
15
14A
9
43D
43D
S250Pb
10PbF2
S300
S300Pb
XC12
CC35
CC45
35MF4
35M5
40M5
20M5
XC38TS
XC42
XC48TS
CC55
XC55
XC60
XC100
Y105
Y120
CF9SMnPb28
CF10Pb20
CF9SMn36
CF9SMnPb36
C16
FeE390KG
C35
C45
C28Mn
C36
C45
C53
C55
C60
C50
C60
C36KU
C120KU
F.111
1350
F.112
1450
F.2111
1912
11SMn28
11SMnPb28 1914
10SPb20
12SMn35
12SMnP35 1926
C15K
1370
2145
F.113
1550
F.114
1650
F210G
1957
36Mn5
2120
1572
C45K
1672
1674
1655
C55K
1678
F.5117
1870
F.5118
1880
F.515
2900
1311
A570.36
15
1015
1020
15
20
1213
Y15
12L13
1215
12L14
1015
1025
A572-60
1035
1045
1140
1039
1335
1330
1035
1045
1050
1055
1060
1055
1060
1095
W1
W210
Y13
15
25
35
45
40Mn
35Mn2
30Mn
35Mn
Ck45
50
55
60
55
60Mn
y ALLOY STEEL
Japan
TECHNICAL DATA
JIS
Q028
SM400A, SM400B
SM400C
SM490A, SM490B
SM490C
SUJ2
SNC236
SNC415(H)
SNC815(H)
SNCM220(H)
Germany
W-nr.
DIN
U.K.
BS
EN
France
Italy
Spain
Sweden
USA
China
AFNOR
UNI
UNE
SS
AISI/SAE
GB
1.0144
St.44.2
4360 43 C
E28-3
1.0570
St52-3
4360 50 B
E36-3
St52-3
55Si7
60SiCr7
100Cr6
15Mo3
16Mo5
14Ni6
X8Ni9
36NiCr6
14NiCr10
14NiCr14
21NiCrMo2
40NiCrMo22
17CrNiMo6
15Cr3
150M19
250A53
45
534A99
31
1501-240
1503-245-420
1501-509-510
640A35
111A
655M13
36A
805M20
362
311-Type 7
820A16
523M15
20MC5
55S7
60SC7
100C6
15D3
16N6
35NC6
14NC11
12NC15
20NCD2
18NCD6
12C3
1.0841
1.0904
1.0961
1.3505
1.5415
1.5423
1.5622
1.5662
1.5710
1.5732
1.5752
1.6523
SNCM240 1.6546
1.6587
SCr415(H) 1.7015
Fe52BFN
Fe52CFN
Fe52
55Si8
60SiCr8
100Cr6
16Mo3KW
16Mo5
14Ni6
X10Ni9
16NiCr11
20NiCrMo2
40NiCrMo2(KB)
1412
A573-81
2132
F.431
56Si7
60SiCr8
F.131
16Mo3
16Mo5
15Ni6
XBNi09
15NiCr11
20NiCrMo2
40NiCrMo2
14NiCrMo13
2172
2085
2258
2912
2506
5120
9255
55Si2Mn
9262
ASTM 52100 Gr15, 45G
ASTM A204Gr.A
4520
ASTM A350LF5
ASTM A353
3135
3415
3415, 3310
8620
8740
5015
15Cr
JIS
Germany
W-nr.
U.K.
DIN
42Cr4
55Cr3
15CrMo5
13CrMo4 4
BS
EN
France
Italy
Spain
Sweden
USA
China
AFNOR
UNI
UNE
SS
AISI/SAE
GB
14CrMo45
42Cr4
12CrMo4
14CrMo45
2245
2216
TU.H
2218
13MoCrV6
35NiCrMo4
35Cr4
42Cr4
16MnCr5
2541
2511
2225
SCr440
SUP9(A)
SCM415(H)
1.7045
1.7176
1.7262
1.7335
1.7380
SCr430(H)
SCr440(H)
SCM420
SCM430
SCM432
SCCRM3
1.7715
1.8523
1.6511
1.6582
1.7033
1.7035
1.7131
1.7218
1.7220
34CrMo4
708A37
19B
35CD4
35CrMo4
34CrMo4
2234
SCM 440
1.7223
41CrMo4
708M40
19A
42CD4TS
41CrMo4
42CrMo4
2244
SCM440(H) 1.7225
42CrMo4
708M40
19A
42CD4
42CrMo4
42CrMo4
2244
4140
SUP10
1.7361
1.8159
32CrMo12 722M24
50CrV4
735A50
40B
47
32CrMo12 F.124.A
50CrV4
51CrV4
2240
2230
6150
1.8509
41CrAlMo7 905M39
41B
41CrAlMo7 41CrAlMo7 2940
1.2067
SKS31
1.2419
SKS2, SKS3
SKT4
1.2713
1.5662
1.5680
1.6657
SKD1
1.2080
100Cr6
105WCr6
BL3
30CD12
50CV4
40CAD6
40CAD2
Y100C6
105WC13
42CrMo
42CrMnMo
50CrVA
L3
CrV, 9SiCr
55NiCrMoV6
X8Ni9
12Ni19
14NiCrMo134
X210Cr12
BH224/5
1501-509
832M13
BD3
36C
55NCDV7
Z18N5
Z200C12
SKD11
SKD12
SKD61
1.2601
1.2363
1.2344
Z100CDV5
Z40CDV5
SKD2
SKD5
SKS43
SKH3
SKH2
SCMnH/1
SUH1
SUH3
SKH9, SKH51
SKH55
1.2436
1.2542
1.2581
1.2601
1.2833
1.3255
1.3355
1.3401
1.4718
1.3343
1.3343
1.3348
1.3243
X153CrMoV12 BD2
X100CrMoV5 BA2
X40CrMoV51 BH13
X40CrMoV51
X210CrW12
45WCrV7 BS1
X30WCrV93 BH21
X165CrMoV12
100V1
BW2
S 18-1-2-5 BT4
S 18-0-1
BT1
G-X120Mn12 Z120M12
X45CrSi93 401S45
S6-5-2
4959BA2
S6/5/2
BM2
S 2-9-2
S6/5/2/5
BM35
52
Z30WCV9
Y1105V
Z80WKCV
Z80WCV
Z120M12
Z45CS9
Z40CSD10
Z85WDCV
6-5-2-5
100Cr6
100WCr6
105WCr5 2140
107WCr5KU
F.520.S
X10Ni9
XBNi09
15NiCrMo13 14NiCrMo131
X210Cr13KU X210Cr12
X250Cr12KU
X160CrMoV12
X100CrMoV5 F.5227
2260
X35CrMoV05KU X40CrMoV5 2242
X40CrMoV51KU
X215CrW121KU X210CrW12 2312
45WCrV8KU 45WCrSi8 2710
X28W09KU X30WCrV9
X165CrMoW12KU X160CrMoV12 2310
X78WCo1805KU HS18-1-1-5
X75W18KU HS18-0-1
XG120Mn12 X120MN12
X45CrSi8 F.322
15NiCrMo13
2715
HS6-5-2-2 F.5603
2722
HS2-9-2
HS2-9-2
2782
HS6-5-2-5 F.5613
2723
527A60
48
1501-620Gr27
1501-622
Gr31, 45
14MoV63 1503-660-440
39CrMoV13 9 897M39
40C
36CrNiMo4 816M40
110
34CrNiMo6 817M40
24
34Cr4
530A32
18B
41Cr4
530M40
18
16MnCr5 (527M20)
25CrMo4 1717CDS110
708M20
10CrMo910
55C3
12CD4
15CD3.5
15CD4.5
12CD9
12CD10
40NCD3
35NCD6
32C4
42C4
16MC5
25CD4
12CrMo9
12CrMo10
36CrMoV12
38NiCrMo4(KB)
35NiCrMo6(KB)
34Cr4(KB)
41Cr4
16MnCr5
25CrMo4(KB)
55Cr3
5140
40Cr
5155
20CrMn
ASTM A182
F11, F12
ASTM A182
F.22
9840
40CrNiMoA
4340
5132
35Cr
5140
40Cr
5115
18CrMn
4130
30CrMn
4137
4135
4140
4142
35CrMo
40CrMoA
CrWMo
L6
5CrNiMo
ASTM A353
2515
D3
Cr12
ASTM D3
D2
Cr12MoV
A2
Cr5Mo1V
H13
40CrMoV5
ASTM H13
S1
H21
30WCrV9
W210
V
W18Cr4VCo5
T4
T1
HW3
X45CrSi93
D3
M2
M7
M35
TECHNICAL DATA
Japan
Q029
TECHNICAL DATA
METALLIC MATERIALS CROSS

REFERENCE LIST
y STAINLESS STEEL (FERRITIC,MARTENSITIC)
Japan
JIS
Germany
W-nr.
U.K.
DIN
BS
EN
France
Italy
Spain
Sweden
USA
China
AFNOR
UNI
UNE
SS
AISI/SAE
GB
SUS403
1.4000
X7Cr13
403S17
Z6C13
F.3110
2301
403
SUS416
SUS410
SUS430
SCS2
SUS420J2
1.4001
1.4005
1.4006
1.4016
1.4027
1.4034
X7Cr14
X12CrS13
X10Cr13
X8Cr17
G-X20Cr14
X46Cr13
416S21
410S21
430S15
420C29
420S45
56A
60
56B
56D
2380
2302
2320
2304
416
410
430
SUS431
SUS430F
SUS434
SCS5
SUS405
SUS430
SUH4
SUH446
SUH35
1.4003
1.4021
1.4057
1.4104
1.4113
1.4313
1.4724
1.4742
1.4747
1.4762
1.4871
1.4521
1.4922
1.4542
405S17
420S37
X22CrNi17 431S29
X12CrMoS17
X6CrMo17 434S17
X5CrNi134 425C11
X10CrA113 403S17
X10CrA118 430S15
X80CrNiSi20 443S65
X10CrA124
X53CrMnNiN219 349S54
X1CrMoTi182
X20CrMoV12-1
F.8401
Z11CF13 X12CrS13 F.3411
Z10C14
X12Cr13 F.3401
Z8C17
X8Cr17
F.3113
Z20C13M
Z40CM
X40Cr14 F.3405
Z38C13M
Z8CA12
X6CrAl13
Z8CA12
X20Cr13
Z15CNi6.02 X16CrNi16 F.3427
Z10CF17 X10CrS17 F.3117
Z8CD17.01 X8CrMo17
Z4CND13.4M (G)X6CrNi304
Z10C13
X10CrA112 F.311
Z10CAS18 X8Cr17
F.3113
Z80CSN20.02 X80CrSiNi20 F.320B
Z10CAS24 X16Cr26
Z52CMN21.09 X53CrMnNiN219
X20CrMoNi1201
Z7CNU17-04
2303
2321
2383
2325
2385
2322
2326
2317
405
420
431
430F
434
CA6-NM
405
430
HNV6
446
EV8
S44400
630
57
60
59
X6Cr13
OCr13
1Cr12
1Cr13
1Cr17
4Cr13
1Cr17Ni2
Y1Cr17
1Cr17Mo
OCr13Al
Cr17
2Cr25N
5Cr2Mn9Ni4N
y STAINLESS STEEL (AUSTENITIC)

Japan
TECHNICAL DATA
JIS
Q030
Germany
W-nr.
U.K.
DIN
BS
EN
France
Italy
Spain
Sweden
USA
AFNOR
UNI
UNE
SS
AISI/SAE
SUS304L
SUS304
1.4306
1.4350
X2CrNi1911 304S11
X5CrNi189 304S11
58E
SUS303
SUS304L
SCS19
SUS301
SUS304LN
SUS316
SCS13
SCS14
SCS22
SUS316LN
SCS16
SUS316L
SUS317L
1.4305
1.4306
1.4310
1.4311
1.4401
1.4308
1.4408
1.4581
1.4429
1.4404
1.4435
X12CrNiS188 303S21
304C12
X2CrNi189 304S12
X12CrNi177
X2CrNiN1810 304S62
X5CrNiMo1810 316S16
G-X6CrNi189 304C15
G-X6CrNiMo1810 316C16
G-X5CrNiMoNb1810 318C17
X2CrNiMoN1813
316S13
316S13
X2CrNiMo1812
58M
58J
1.4436
1.4438
1.4539
316S13
X2CrNiMo1816 317S12
Z6CND18-12-03 X8CrNiMo1713
Z2CND19.15 X2CrNiMo1816
Z6CNT18.10
SUS321
1.4541
321S12
58B
SUS347
1.4550
347S17
58F
1.4571
1.4583
X10CrNiMoTi1810 320S17
X10CrNiMoNb1812
58J
Z6CNT18.10 X6CrNiTi1811 F.3553

F.3523
Z6CNNb18.10 X6CrNiNb1811 F.3552
F.3524
Z6CNDT17.12 X6CrNiMoTi1712 F.3535
Z6CNDNb1713B X6CrNiMoNb1713
X1NiCrMo
X10CrNiTi189
X10CrNiNb189
Z2CN18.10 X2CrNi18.11
Z6CN18.09 X5CrNi1810 F.3551
F.3541
F.3504
Z10CNF18.09 X10CrNiS18.09 F.3508
Z3CN19.10
Z2CrNi1810 X2CrNi18.11 F.3503
Z12CN17.07 X12CrNi1707 F.3517
Z2CN18.10
Z6CND17.11 X5CrNiMo1712 F.3543
Z6CN18.10M
F.8414
Z4CNDNb1812M XG8CrNiMo1811
Z2CND17.13
China
GB
2352
2332
304L
304
OCr19Ni10
OCr18Ni9
2346
2333
2352
2331
2371
2347
2375
2348
2353
303
304L
301
304LN
316
316LN
316L
316L
1Cr18Ni9MoZr
Cr17Ni7
0Cr17Ni11Mo2
OCr17Ni13Mo
OCr27Ni12Mo3
2343, 2347 316

2367
317L
2562
UNS V
0890A
2337
321
OOCr19Ni13Mo
2338
347
2350
316Ti
318
1Cr18NI9Ti
1Cr18Ni11Nb
Cr18Ni12Mo2T
Cr17Ni12Mo3Mb
Japan
JIS
Germany
W-nr.
U.K.
DIN
BS
EN
France
Italy
Spain
Sweden
USA
China
AFNOR
UNI
UNE
SS
AISI/SAE
GB
X15CrNiSi2012 309S24
X12CrNi2521 310S24
X10CrNi18.08
X4CrNiMo165
316S111
58C
Z15CNS20.12 X6CrNi2520
Z12CN2520 X6CrNi2520 F.331
Z1NCDU25.20
F.8414
Z6CND16-04-01
Z8CNA17-07 X2CrNiMo1712
2361
2370
309
310S
308
17-7PH
1Cr23Ni13
OCr25Ni20
1.4828
1.4845
1.4406
1.4418
1.4568
1.4504
1.4563
1.4878
X12CrNiTi189 321S32
2584
2378
NO8028
S31254
321
SUS321
Z1NCDU31-27-03
Z1CNDU20-18-06AZ
Z6CNT18.12B X6CrNiTi18 11 F.3523
SUH309
SUH310
SCS17
58B, 58C
1Cr18Ni9Ti
y HEAT RESISTANT STEELS

Japan
JIS
SUH330
SCH15
Germany
W-nr.
U.K.
DIN
BS
EN
X12NiCrSi3616
G-X40NiCrSi3818 330C11
1.4864
1.4865
France
Italy
Spain
Sweden
USA
China
AFNOR
UNI
UNE
SS
AISI/SAE
GB
Z12NCS35.16
XG50NiCr3919
330
HT, HT 50
y GRAY CAST IRON

Japan
JIS
FC100
FC150
FC200
FC250
FC300
FC350
Germany
W-nr.
0.6015
0.6020
0.6025
0.6030
0.6035
0.6040
0.6660
U.K.
DIN
BS
EN
GG 10
GG 15
Grade 150
GG 20
Grade 220
GG 25
Grade 260
GG 30
Grade 300
GG 35
Grade 350
GG 40
Grade 400
GGL NiCr202 L-NiCuCr202
France
Italy
Spain
Sweden
USA
China
AFNOR
UNI
UNE
SS
AISI/SAE
GB
Ft 10 D
Ft 15 D
Ft 20 D
Ft 25 D
Ft 30 D
Ft 35 D
Ft 40 D
L-NC 202
G15
G20
G25
G30
G35
FG15
FG25
FG30
FG35
0100
0110
0115
0120
0125
0130
0135
0140
0523
No 20 B
No 25 B
HT150
No 30 B
HT200
No 35 B
HT250
No 40 B
No 45 B
HT300
No 50 B
HT350
No 55 B
HT400
A436 Type 2
y DUCTILE CAST IRON

JIS
FCD400
FCD500
FCD600
FCD700
Germany
W-nr.
0.7040
0.7033
0.7050
0.7660
0.7070
U.K.
DIN
BS
EN
GGG 40
SNG 420/12
GGG 40.3 SNG 370/17
GGG 35.3
GGG 50
SNG 500/7
GGG NiCr202 Grade S6
GGG NiMn137 L-NiMn 137
GGG 60
SNG 600/3
GGG 70
SNG 700/2
France
Italy
Spain
Sweden
USA
AFNOR
UNI
UNE
SS
AISI/SAE
FCS 400-12 GS 370-17

FGS 370-17
FGS 500-7 GS 500

S-NC202
L-MN 137
FGS 600-3
FGS 700-2 GS 700-2
FGE 38-17
FGE 50-7
FGS 70-2
07 17-02
07 17-12
07 17-15
07 27-02
07 76
07 72
07 32-03
07 37-01
60-40-18
80-55-06
A43D2
100-70-03
China
GB
QT400-18
QT500-7
QT600-3
QT700-18
y MALLEABLE CAST IRON

Japan
JIS
FCMB310
FCMW330
FCMW370
FCMP490
FCMP540
FCMP590
FCMP690
Germany
W-nr.
0.8145
0.8155
0.8165
DIN
GTS-35
GTS-45
GTS-55
GTS-65
GTS-65-02
GTS-70-02
U.K.
BS
8 290/6
B 340/12
P 440/7
P 510/4
P 570/3
P 570/3
P 690/2
France
EN
AFNOR
MN 32-8
MN 35-10
Mn 450
MP 50-5
MP 60-3
Mn 650-3
Mn 700-2
Italy
Spain
UNI
UNE
GMN45
GMN55
GMN 65
GMN 70
Sweden
SS
08 14
08 15
08 52
08 54
08 58
08 56
08 62
USA
China
AISI/SAE
GB
32510
40010
50005
70003
A220-70003
A220-80002
TECHNICAL DATA
Japan
Q031
TECHNICAL DATA
DIE STEELS
Classification
Carbon Tool Steel
AUK1
S55C
SCM440
AUK11
Alloy Steel for

Machine Structure
S50C
Aichi Steel
Kobe Steel,
Uddeholm
Works
Ltd.
Carbon Steel for

Machine Structure
JIS (Others)
SCM445
SK3
SKS3
SKS31
SKS93
SKD1
SKD11
SKD11
SKD11
SKD12
HOLDAX
KTSM2A
KTSM21
KTSM22
KTSM3A
KTSM31
SK3
SKS3
Sumitomo
Daido Steel
Metal
Co., Ltd.
Industries, Ltd.
SD10
SD17
SD21
SD61
PDS1
PXZ
SKD11
AUD11
KAD181
RIGOR
DC11
DC3
DC12
SX4
SX44
SX105V
TCD
Alloy Tool Steel

(For Cold Working)
KPM1
K3
KS3
K31
K3M
KD1
KD11
KD11V
KDQ
KD12
DC53
PD613
GO4
GO5
GO40F
(P20)
(P20)
(P21)
SKD4
SKD5
SKD6
SKD61
SKD61
SKD62
SKT4
SKD7
(H10)
SKD8
IMPAX
SKD61
MT50C
YC3
SGT
YCS3
CRD
SLD
SLD2
SCD
FH5
KD21
KDM5
KD11S
Alloy Tool Steel

(For Cold Working
and Others)
Mitsubishi Steel
Hitachi
Manufacturing
Metals, Ltd.
Co., Ltd.
PDS3
YK3
GOA
GO31
YK30
SK301
Nippon
Koshuha
Over M
Suprem
SKD62
KTSM3M
PX5
KPM30
KTSM40EF
KTSM40E
NAK55
NAK80
GLD2
DH4
DH5
DH6
DHA1
KAP
KAP2
DH62
GFA
DH72
DH73
DH41
KD4
KD5
KD6
KDA
MFA
KDB
KTV
KDH1
KDF
SLD8
ACD37
HMD5
HPM2T
YSM
HPM31
HMD1
HMD5
ACD6
ACD8
ACD9
HPM2
HPM7
HPM1
HPM50
CENA1
YDC
HDC
DAC
DBC
DM
YEM
MDC
QRO80M
YHD40
DH71
DH42
DH21
KDW
KDHM
AE31
TECHNICAL DATA
Alloy Tool Steel

(For Hot Working)
SKT4
6F4
SKT4
YEM4
YHD50
YHD26
SKT4A
MPH
DH31
KDA1
KDA5
GF78
DH76
DH2F
Q032
TD3
KDAS
DAC3
DAC10
DAC40
DAC45
DAC55
FDAC
YHD3
MDC K
YEM K
MT24M
Classification
JIS (Others)
Aichi Steel
Kobe Steel,
Uddeholm
Works
Ltd.
Sumitomo
Daido Steel
Metal
Co., Ltd.
Industries, Ltd.
Nippon
Koshuha
Mitsubishi Steel
Hitachi
Manufacturing
Metals, Ltd.
Co., Ltd.
SKH51
MH51
H51
YXM1
SKH55
MH55
HM35
YXM4
SKH57
MH57
MV10
XVC5
MH8
NK4
YXM60
HV2
XVC11
HM3
YXM7
MH85
KDMV
YXR3
MH88
HM9TL
YXR4
MH24
MH7V1
High-speed
Tool Steel
MH64
VH54
YXR7
YXR35
ASP23
KHA32
DEX20
HAP10
ASP30
KHA30
DEX40
HAP40
KHA3VN
DEX60
HAP50
KHA30N
DEX70
HAP63
KHA33N
DEX80
HAP72
Powder
High-speed
Tool Steel
KHA50
KHA77
ASP60
KHA60
SUS403
Stainless Steel
GLD1
SUS420
STAVAX
SUS440C
ELMAX
(Powder)
KAS440
(Powder)
S STAR
KSP1
SUS440C
KSP3
SUS420
SUS630
HPM38
SUS420
NAK101
U630
PSL
MAS1C
KMS1820
YAG
(414)

Forged Tool
DMG300
HRNC
ICD1
ICD5
TECHNICAL DATA
Maraging Steel
Q033
TECHNICAL DATA
SURFACE ROUGHNESS
SURFACE ROUGHNESS
Ten-Point Mean Roughness
Maximum Height
Arithmetical
Mean Roughness
Type Code
Ra
Rz
(From JIS B 0601-1994)

Determination Example (Figure)
Determination
Ra means the value obtained by the following formula and
expressed in micrometer ( !m ) when sampling only the
reference length from the roughness curve in the direction of
the mean line, taking X-axis in the direction of mean line and
Y-axis in the direction of longitudinal magnification of this
sampled part and the roughness curve is expressed by y=f(x):
RZ shall be that only when the reference length is sampled from the
roughness curve in the direction of the mean line, the distance
between the top profile peak line and the bottom profile valley line
on this sampled portion is measured in the longitudinal
magnification direction of roughness curve and the obtained value
is expressed in micrometer (!m).
(Note) When finding Rz, a portion without an exceptionally high
peak or low valley, which may be regarded as a flaw, is
selected as the sampling length.
RZJIS shall be that only when the reference length is sampled from
the roughness curve in the direction of its mean line, the sum of
the average value of absolute values of the heights of five highest
profile peaks (Yp) and the depths of five deepest profile valleys (Yv)
measured in the vertical magnification direction from the mean line
of this sampled portion and this sum is expressed in micrometer
(!m).
RZJIS
: altitudes of the five highest profile peaks
of the sampled portion corresponding to
the reference length l.
: altitudes of the five deepest profile
valleys of the sampled portion
corresponding to the reference length l.
y RELATIONSHIP BETWEEN ARITHMETICAL MEAN (Ra) AND CONVENTIONAL DESIGNATION (REFERENCE DATA)
0.08
0.025 a
TECHNICAL DATA
0.05 a
0.25
RZJIS
0.05 s
0.05 z
0.1 s
0.1 z
0.2 s
0.2 z
0.4 s
0.4 z
0.8 s
0.8 z
1.6 s
1.6 z
0.2
0.4
0.8
3.2 s
3.2 z
1.6
6.3 s
6.3 z
3.2
6.3
12.5
25
50
100
2.5
12.5 s
12.5 z
25
25
Rz RZJIS
l (mm)
Standard Series
0.1
0.8
Sampling Length for
50
50
100
100
200
200
400
400
0.08
0.25
0.8
2.5
correlation among the three is shown for convenience and is not exact.
*The
Ra: The evaluation length of Rz and Rz is the cutoff value and sampling length multiplied by 5, respectively.
*
JIS
Q034
Conventional Finish
Mark
0.012 a
Ten-Point Mean Roughness
Rz
]]
Standard Series
Cutoff Value
"c (mm)
Max. Height
]]]
Ra
]]]]
Arithmetical Mean Roughness
HARDNESS COMPARISON TABLE

(HV)
(HRA)
(HRB)
(HRC)
(HRD)
(HS)
Standard Tungsten
Ball Carbide Ball
Rockwell Hardness
A Scale,
B Scale,
C Scale,
D Scale,
Load:60kgf, Load:100kgf, Load:150kgf, Load:100kgf,
Diamond
1/16" Ball
Diamond
Diamond
Point
Point
Point
Tensile
Strength
(Approx.)
Mpa
(HV)
(HRA)
(HRB)
(HRC)
(HRD)
(HS)
(767)
(757)
940
920
900
880
860
85.6
85.3
85.0
84.7
84.4
68.0
67.5
67.0
66.4
65.9
76.9
76.5
76.1
75.7
75.3
97
96
95
93
92
429
415
401
388
375
429
415
401
388
375
455
440
425
410
396
73.4
72.8
72.0
71.4
70.6
45.7
44.5
43.1
41.8
40.4
59.7
58.8
57.8
56.8
55.7
61
59
58
56
54
1510
1460
1390
1330
1270
(745)
(733)
(722)
(712)
(710)
(698)
840
820
800
780
760
84.1
83.8
83.4
83.0
82.6
65.3
64.7
64.0
63.3
62.5
74.8
74.3
73.8
73.3
72.6
91
90
88
87
86
363
352
341
331
321
363
352
341
331
321
383
372
360
350
339
70.0
69.3
68.7
68.1
67.5
(110.0)
(109.0)
(108.5)
(108.0)
39.1
37.9
36.6
35.5
34.3
54.6
53.8
52.8
51.9
51.0
52
51
50
48
47
1220
1180
1130
1095
1060
(684)
(682)
(670)
(656)
(653)
740
737
720
700
697
82.2
82.2
81.8
81.3
81.2
61.8
61.7
61.0
60.1
60.0
72.1
72.0
71.5
70.8
70.7
84
83
81
311
302
293
285
277
311
302
293
285
277
328
319
309
301
292
66.9
66.3
65.7
65.3
64.6
(107.5)
(107.0)
(106.0)
(105.5)
(104.5)
33.1
32.1
30.9
29.9
28.8
50.0
49.3
48.3
47.6
46.7
46 1025
45 1005
43 970
950
41 925
(647)
(638)
630
627
690
680
670
667
81.1
80.8
80.6
80.5
59.7
59.2
58.8
58.7
70.5
70.1
69.8
69.7
80
79
269
262
255
248
241
269
262
255
248
241
284
276
269
261
253
64.1
63.6
63.0
62.5
61.8
(104.0)
(103.0)
(102.0)
(101.0)
100
27.6
26.6
25.4
24.2
22.8
45.9
45.0
44.2
43.2
42.0
40
39
38
37
36
895
875
850
825
800
601
677
640
80.7
79.8
59.1
57.3
70.0
68.7
77
578
640
615
79.8
79.1
57.3
56.0
68.7
67.7
75
235
229
223
217
212
235
229
223
217
212
247
241
234
228
222
61.4
60.8
99.0
98.2
97.3
96.4
95.5
21.7
20.5
(18.8)
(17.5)
(16.0)
41.4
40.5
35
34
33
785
765
725
705
555
607
591
78.8
78.4
55.6
54.7
67.4
66.7
73 2055
534
579
569
78.0
77.8
54.0
53.5
66.1
65.8
2015
71 1985
207
201
197
192
187
207
201
197
192
187
218
212
207
202
196
94.6
93.8
92.8
91.9
90.7
(15.2)
(13.8)
(12.7)
(11.5)
(10.0)
32
31
30
29
690
675
655
640
620
514
533
547
77.1
76.9
52.5
52.1
65.0
64.7
1915
70 1890
(495)
495
539
530
528
76.7
76.4
76.3
51.6
51.1
51.0
64.3
63.9
63.8
1855
1825
68 1820
183
179
174
170
167
183
179
174
170
167
192
188
182
178
175
90.0
89.0
87.8
86.8
86.0
(9.0)
(8.0)
(6.4)
(5.4)
(4.4)
28
27
26
615
600
585
570
560
(477)
477
516
508
508
75.9
75.6
75.6
50.3
49.6
49.6
63.2
62.7
62.7
1780
1740
66 1740
(461)
461
495
491
491
75.1
74.9
74.9
48.8
48.5
48.5
61.9
61.7
61.7
1680
1670
65 1670
163
156
149
143
137
163
156
149
143
137
171
163
156
150
143
85.0
82.9
80.8
78.7
76.4
(3.3)
(0.9)
25
23
22
21
545
525
505
490
460
444
474
472
472
74.3
74.2
74.2
47.2
47.1
47.1
61.0
60.8
60.8
1595
1585
63 1585
131
126
121
116
111
131
126
121
116
111
137
132
127
122
117
74.0
72.0
69.8
67.6
65.7
20
19
18
15
450
435
415
400
385
444
TECHNICAL DATA
Mpa
Brinell Hardness (HB)

10mm Ball,Load: 3,000 kgf
Shore
Hardness
A Scale,
B Scale,
C Scale,
D Scale,
Load:60kgf, Load:100kgf, Load:150kgf, Load:100kgf,
Diamond
1/16" Ball
Diamond
Diamond
Point
Point
Point
Tensile
Strength
(Approx.)
Vickers
Hardness
Standard Tungsten
Ball Carbide Ball
Rockwell Hardness
Shore
Hardness
Brinell Hardness (HB)

10mm Ball,Load: 3,000 kgf
Vickers
Hardness
HARDNESS CONVERSION NUMBERS OF STEEL
(Note 1) Above list is the same as that at AMS Metals Hand book with tensile strength in approximate metric value and Brinell hardness over a
recommended range.
(Note 2) 1MPa=1N/mm2
(Note 3) Figures in ( ) are rarely used and are included for reference. This list has been taken from JIS Handbook Steel I.
Q035
TECHNICAL DATA
FIT TOLERANCE TABLE (HOLE)

Classification
of Standard
Dimensions
(mm)
>
TECHNICAL DATA
10
10
14
14
18
18
24
24
30
30
40
40
50
50
65
65
80
80
100
100
120
120
140
140
160
160
180
180
200
200
225
225
250
250
280
280
315
315
355
355
400
400
450
450
500
Class of Geometrical Tolerance Zone of Holes
B10
C9
C10
D8
D9
D10
E7
E8
E9
F6
F7
F8
G6
G7
H6
H7
+180
+140
+188
+140
+208
+150
+85
+60
+100
+70
+116
+80
+100
+60
+118
+70
+138
+80
+34
+20
+48
+30
+62
+40
+45
+20
+60
+30
+76
+40
+60
+20
+78
+30
+98
+40
+24
+14
+32
+20
+40
+25
+28
+14
+38
+20
+47
+25
+39
+14
+50
+20
+61
+25
+12
+6
+18
+10
+22
+13
+16
+6
+22
+10
+28
+13
+20
+6
+28
+10
+35
+13
+8
+2
+12
+4
+14
+5
+12
+2
+16
+4
+20
+5
+6
0
+8
0
+9
0
+10
0
+12
0
+15
0
+220
+150
+138
+95
+165
+95
+77
+50
+93
+50
+120
+50
+50
+32
+59
+32
+75
+32
+27
+16
+34
+16
+43
+16
+17
+6
+24
+6
+11
0
+18
0
+244
+160
+162
+110
+194
+110
+98
+65
+117
+65
+149
+65
+61
+40
+73
+40
+92
+40
+33
+20
+41
+20
+53
+20
+20
+7
+28
+7
+13
0
+21
0
+270
+170
+280
+180
+310
+190
+320
+200
+182
+120
+192
+130
+214
+140
+224
+150
+220
+120
+230
+130
+260
+140
+270
+150
+119
+80
+142
+80
+180
+80
+75
+50
+89
+50
+112
+50
+41
+25
+50
+25
+64
+25
+25
+9
+34
+9
+16
0
+25
0
+146
+100
+174
+100
+220
+100
+90
+60
+106
+60
+134
+60
+49
+30
+60
+30
+76
+30
+29
+10
+40
+10
+19
0
+30
0
+360
+220
+380
+240
+420
+260
+440
+280
+470
+310
+257
+170
+267
+180
+300
+200
+310
+210
+330
+230
+310
+170
+320
+180
+360
+200
+370
+210
+390
+230
+174
+120
+207
+120
+260
+120
+107
+72
+126
+72
+159
+72
+58
+36
+71
+36
+90
+36
+34
+12
+47
+12
+22
0
+35
0
+208
+145
+245
+145
+305
+145
+125
+85
+148
+85
+185
+85
+68
+43
+83
+43
+106
+43
+39
+14
+54
+14
+25
0
+40
0
+525
+340
+565
+380
+605
+420
+690
+480
+750
+540
+355
+240
+375
+260
+395
+280
+430
+300
+460
+330
+425
+240
+445
+260
+465
+280
+510
+300
+540
+330
+242
+170
+285
+170
+355
+170
+146
+100
+172
+100
+215
+100
+79
+50
+96
+50
+122
+50
+44
+15
+61
+15
+29
0
+46
0
+271
+190
+320
+190
+400
+190
+162
+110
+191
+110
+240
+110
+88
+56
+108
+56
+137
+56
+49
+17
+69
+17
+32
0
+52
0
+830
+600
+910
+680
+1010
+760
+1090
+840
+500
+360
+540
+400
+595
+440
+635
+480
+590
+360
+630
+400
+690
+440
+730
+480
+299
+210
+350
+210
+440
+210
+182
+125
+214
+125
+265
+125
+98
+62
+119
+62
+151
+62
+54
+18
+75
+18
+36
0
+57
0
+327
+230
+385
+230
+480
+230
+198
+135
+232
+135
+290
+135
+108
+68
+131
+68
+165
+68
+60
+20
+83
+20
+40
0
+63
0
(Note) Values shown in the upper portion of respective lines are upper dimensional tolerance, while values shown in the lower portion of
respective lines are lower dimensional tolerance.
Q036
Units : !m
Class of Geometrical Tolerance Zone of Holes
H9
H10
+14
0
+18
0
+22
0
+25
0
+30
0
+36
0
+40
0
+48
0
+58
0
+27
0
+43
0
+70
0
JS6
JS7
e3
e5
e4
e6
e4.5
e7
e5.5
e9
K6
K7
M6
M7
N6
N7
P6
P7
R7
S7
2
12
+2
6
+2
7
0
10
+3
9
+5
10
2
8
1
9
3
12
0
12
0
15
4
10
5
13
7
16
4
14
4
16
4
19
6
12
9
17
12
21
6
16
8
20
9
24
10
20
11
23
13
28
14
24
15
27
17
32
+2
9
+6
12
4
15
0
18
9
20
5
23
15
26
11
29
16
34
21
39
0
6
e10
+2
11
+6
15
4
17
0
21
11
24
7
28
18
31
14
35
20
41
27
48
e12
+3
13
+7
18
4
20
0
25
12
28
8
33
21
37
17
42
25
50
34
59
e15
+4
15
+9
21
5
24
0
30
14
33
9
39
26
45
21
51
+140
e11
0
e17
+4
18
+10
25
6
28
0
35
16
38
10
45
30
52
24
59
+100
0
+160
e12.5
0
e20
+4
21
+12
28
8
33
0
40
20
45
12
52
36
61
28
68
+72
0
+115
0
+185
e14.5
0
e23
+5
24
+13
33
8
37
0
46
22
51
14
60
41
70
33
79
42
72
48
78
58
93
66
101
77
117
85
125
93
133
105
151
113
159
123
169
+81
0
+130
0
+210
e16
0
e26
+5
27
+16
36
9
41
0
52
25
57
14
66
47
79
36
88
+89
0
+140
0
+230
e18
0
e28
+7
29
+17
40
10
46
0
57
26
62
16
73
51
87
41
98
+97
0
+155
0
+250
e20
0
e31
+8
32
+18
45
10
50
0
63
27
67
17
80
55
95
45
108
30
60
32
62
38
73
41
76
48
88
50
90
53
93
60
106
63
109
67
113
74
126
78
130
87
144
93
150
103
166
109
172
+33
0
+52
0
+84
0
+39
0
+62
0
+100
0
+46
0
+74
0
+120
0
+54
0
+87
0
+63
0
e6.5
e8
e9.5
T7
33
54
39
64
45
70
55
85
64
94
78
113
91
126
107
147
119
159
131
171
U7
X7
18
28
19
31
22
37
20
30
24
36
28
43
33
51
38
56
46
67
56
77
26
44
33
54
40
61
51
76
61
86
76
106
91
121
111
146
131
166
TECHNICAL DATA
H8
Q037
TECHNICAL DATA
FIT TOLERANCE TABLE (SHAFTS)

Classification
of Standard
Dimensions
(mm)
>
TECHNICAL DATA
3
3
10
10
14
14
18
18
24
24
30
30
40
40
50
50
65
65
80
80
100
100
120
120
140
140
160
160
180
180
200
200
225
225
250
250
280
280
315
315
355
355
400
400
450
450
500
Class of Geometrical Tolerance Zone of Shafts
b9
c9
d8
d9
e7
e8
e9
f6
f7
f8
g5
g6
h5
h6
h7
140
165
140
170
150
186
60
85
70
100
80
116
20
34
30
48
40
62
20
45
30
60
40
76
14
24
20
32
25
40
14
28
20
38
25
47
14
39
20
50
25
61
6
12
10
18
13
22
6
16
10
22
13
28
6
20
10
28
13
35
2
6
4
9
5
11
2
8
4
12
5
14
0
4
0
5
0
6
0
6
0
8
0
9
0
10
0
12
0
15
150
193
95
138
50
77
50
93
32
50
32
59
32
75
16
27
16
34
16
43
6
14
6
17
0
8
0
11
0
18
160
212
110
162
65
98
65
117
40
61
40
73
40
92
20
33
20
41
20
53
7
16
7
20
0
9
0
13
0
21
170
232
180
242
190
264
200
274
220
307
240
327
260
360
280
380
310
410
340
455
380
495
420
535
480
610
540
670
600
740
680
820
760
915
840
995
120
182
130
192
140
214
150
224
170
257
180
267
200
300
210
310
230
330
240
355
260
375
280
395
300
430
330
460
360
500
400
540
440
595
480
635
80
119
80
142
50
75
50
89
50
112
25
41
25
50
25
64
9
20
9
25
0
11
0
16
0
25
100
146
100
174
60
90
60
106
60
134
30
49
30
60
30
76
10
23
10
29
0
13
0
19
0
30
120
174
120
207
72
107
72
126
72
159
36
58
36
71
36
90
12
27
12
34
0
15
0
22
0
35
145
208
145
245
85
125
85
148
85
185
43
68
43
83
43
106
14
32
14
39
0
18
0
25
0
40
170
242
170
285
100
146
100
172
100
215
50
79
50
96
50
122
15
35
15
44
0
20
0
29
0
46
190
271
190
320
110
162
110
191
110
240
56
88
56
108
56
137
17
40
17
49
0
23
0
32
0
52
210
299
210
350
125
182
125
214
125
265
62
98
62
119
62
151
18
43
18
54
0
25
0
36
0
57
230
327
230
385
135
198
135
232
135
290
68
108
68
131
68
165
20
47
20
60
0
27
0
40
0
63
(Note) Values shown in the upper portion of respective lines are upper dimensional tolerance, while values shown in the lower portion of
respective lines are lower dimensional tolerance.
Q038
Units : !m
Class of Geometrical Tolerance Zone of Shafts
h9
0
14
0
18
0
22
0
25
0
30
0
36
0
27
0
43
0
33
0
52
0
39
0
62
0
46
0
74
0
54
0
87
0
63
0
100
js5
js6
js7
k5
k6
m5
m6
n6
p6
r6
s6
+4
0
+6
+1
+7
+1
+6
0
+9
+1
+10
+1
+6
+8
+2
+9
+4
+12
+6
+2
+12
+4
+15
+6
+10
+4
+16
+8
+19
+10
+12
+6
+20
+12
+24
+15
+16
+10
+23
+15
+28
+19
+20
+14
+27
+19
+32
+23
e9
+9
+1
+12
+1
+15
+7
+18
+7
+23
+12
+29
+18
+34
+23
+39
+28
e10
+11
+2
+15
+2
+17
+8
+21
+8
+28
+15
+35
+22
+41
+28
+48
+35
e12
+13
+2
+18
+2
+20
+9
+25
+9
+33
+17
+42
+26
+50
+34
+59
+43
e15
+15
+2
+21
+2
+24
+11
+30
+11
+39
+20
+51
+32
+60
+41
+62
+43
+25
+3
+28
+13
+35
+13
+45
+23
+59
+37
+28
+3
+33
+15
+40
+15
+52
+27
+68
+43
e2
e3
e5
e2.5
e4
e6
e3
e4.5
e7
e4
e4.5
e5.5
e6.5
e5.5
e6.5
e8
e9.5
e7.5
e11
e17
+18
+3
e9
e12.5
e20
+21
+3
0
72
0
115
e10
e14.5
e23
+24
+4
+33
+4
+37
+17
+46
+17
+60
+31
+79
+50
0
81
0
130
e11.5
e16
e26
+27
+4
+36
+4
+43
+20
+52
+20
+66
+34
+88
+56
0
89
0
140
e12.5
e18
e28
+29
+4
+40
+4
+46
+21
+57
+21
+73
+37
+98
+62
0
97
0
155
e13.5
e20
e31
+32
+5
+45
+5
+50
+23
+63
+23
+80
+40
+108
+68
t6
u6
x6
+24
+18
+31
+23
+37
+28
+26
+20
+36
+28
+43
+34
+44
+33
+51
+40
+56
+45
+67
+54
+77
+64
+54
+41
+54
+41
+61
+48
+72
+53
+78
+59
+64
+48
+70
+54
+85
+66
+94
+75
+76
+60
+86
+70
+106
+87
+121
+102
+73
+51
+76
+54
+88
+63
+90
+65
+93
+68
+93
+71
+101
+79
+117
+92
+125
+100
+133
+108
+113
+91
+126
+104
+147
+122
+159
+134
+171
+146
+146
+124
+166
+144
+106
+77
+109
+80
+113
+84
+126
+94
+130
+98
+151
+122
+159
+130
+169
+140
+144
+108
+150
+114
+166
+126
+172
+132
TECHNICAL DATA
h8
Q039
TECHNICAL DATA
DRILL DIAMETERS
FOR PREPARED HOLES
a Metric Coarse Screw
Thread
TECHNICAL DATA
Nominal
Drill Diameter
HSS Carbide
a Metric Fine Screw
Thread
Nominal
Drill Diameter
HSS Carbide
Nominal
Drill Diameter
HSS Carbide
Nominal
Drill Diameter
HSS Carbide
M1 0.25
0.75
0.75
M1 0.2
0.80
0.80
M20 2.0
18.0
18.3
M42 3.0
39.0
M1.1 0.25
0.85
0.85
M1.10.2
0.90
0.90
M20 1.5
18.5
18.7
M42 2.0
40.0
M1.2 0.25
0.95
0.95
M1.20.2
1.00
1.00
M20 1.0
19.0
19.1
M42 1.5
40.5
M1.4 0.3
1.10
1.10
M1.40.2
1.20
1.20
M22 2.0
20.0
M45 4.0
41.0
M1.6 0.35
1.25
1.30
M1.60.2
1.40
1.40
M22 1.5
20.5
M45 3.0
42.0
M1.7 0.35
1.35
1.40
M1.80.2
1.60
1.60
M22 1.0
21.0
M45 2.0
43.0
M1.8 0.35
1.45
1.50
M2 0.25
1.75
1.75
M24 2.0
22.0
M45 1.5
43.5
M2 0.4
1.60
1.65
M2.20.25
1.95
2.00
M24 1.5
22.5
M48 4.0
44.0
M2.2 0.45
1.75
1.80
M2.50.35
2.20
2.20
M24 1.0
23.0
M48 3.0
45.0
M2.3 0.4
1.90
1.95
M3 0.35
2.70
2.70
M25 2.0
23.0
M48 2.0
46.0
M2.5 0.45
2.10
2.15
M3.50.35
3.20
3.20
M25 1.5
23.5
M48 1.5
46.5
M2.6 0.45
2.15
2.20
M4 0.5
3.50
3.55
M25 1.0
24.0
M50 3.0
47.0
M3 0.5
2.50
2.55
M4.50.5
4.00
4.05
M26 1.5
24.5
M50 2.0
48.0
M3.5 0.6
2.90
2.95
M5 0.5
4.50
4.55
M27 2.0
25.0
M50 1.5
48.5
M4 0.7
3.3
3.4
M5.50.5
5.00
5.05
M27 1.5
25.5
M4.5 0.75
3.8
3.9
M6 0.75
5.30
5.35
M27 1.0
26.0
M5 0.8
4.2
4.3
M7 0.75
6.30
6.35
M28 2.0
26.0
M6 1.0
5.0
5.1
M8 1.0
7.00
7.10
M28 1.5
26.5
M7 1.0
6.0
6.1
M8 0.75
7.30
7.35
M28 1.0
27.0
M8 1.25
6.8
6.9
M9 1.0
8.00
8.10
M30 3.0
27.0
M9 1.25
7.8
7.9
M9 0.75
8.30
8.35
M30 2.0
28.0
M10 1.5
8.5
8.7
M10 1.25
8.80
8.90
M30 1.5
28.5
M11 1.5
9.5
9.7
M10 1.0
9.00
9.10
M30 1.0
29.0
M12 1.75
10.3
10.5
M10 0.75
9.30
9.35
M32 2.0
30.0
M14 2.0
12.0
12.2
M11 1.0
10.0
10.1
M32 1.5
30.5
M16 2.0
14.0
14.2
M11 0.75
10.3
10.3
M33 3.0
30.0
M18 2.5
15.5
15.7
M12 1.5
10.5
10.7
M33 2.0
31.0
M20 2.5
17.5
17.7
M12 1.25
10.8
10.9
M33 1.5
31.5
M22 2.5
19.5
19.7
M12 1.0
11.0
11.1
M35 1.5
33.5
M24 3.0
21.0
M14 1.5
12.5
12.7
M36 3.0
33.0
M27 3.0
24.0
M14 1.0
13.0
13.1
M36 2.0
34.0
M30 3.5
26.5
M15 1.5
13.5
13.7
M36 1.5
34.5
M33 3.5
29.5
M15 1.0
14.0
14.1
M38 1.5
36.5
M36 4.0
32.0
M16 1.5
14.5
14.7
M39 3.0
36.0
M39 4.0
35.0
M16 1.0
15.0
15.1
M39 2.0
37.0
M42 4.5
37.5
M17 1.5
15.5
15.7
M39 1.5
37.5
M45 4.5
40.5
M17 1.0
16.0
16.1
M40 3.0
37.0
M48 5.0
43.0
M18 2.0
16.0
16.3
M40 2.0
38.0
M18 1.5
16.5
16.7
M40 1.5
38.5
M18 1.0
17.0
17.1
M42 4.0
38.0
(Note) When using the drill diameters shown in this table, that the processed hole should be measured since the size accuracy of a drill hole
may change due to the drilling condition, and that if found to be inappropriate for a prepared hole, the drill diameter must be corrected
accordingly.
Q040
HEXAGON SOCKET HEAD BOLT HOLE SIZE

M3
M4
M5
M6
M8 M10 M12 M14 M16 M18 M20 M22 M24 M27 M30
d1
10
12 14
16
18
20
22
24
27
30
d'
3.4 4.5
5.5
6.6
11
14 16
18
20
22
24
26
30
33
5.5 7
8.5 10
13
16
18 21
24
27
30
33
36
40
45
D'
6.5 8
9.5 11
14
17.5 20 23
26
29
32
35
39
43
48
10
16
18
20
22
24
27
30
H'
2.7 3.6
4.6
5.5
7.4
9.2 11 12.8 14.5 16.5 18.5 20.5 22.5 25
28
H"
3.3 4.4
5.4
6.5
8.6 10.8 13 15.2 17.5 19.5 21.5 23.5 25.5 29
32
D'
D
d'
12 14
D'
D
d'
d1
TECHNICAL DATA
d1
H'
H
Nominal
dimensions
of thread d
Unit : mm
H
H"
DIMENSIONS OF COUNTERBORING FOR

HEXAGON SOCKET HEAD CAP SCREW AND BOLT HOLE
Q041
TECHNICAL DATA
TAPER STANDARD
Taper 7/24
t3
d3
d2
I1
CRKS
t2
DF
I4
60
DF
DF_2
d1
60
CRKS
Taper 7/24
I2
National Taper
d3
Bolt Grip Taper
(d5)
I3
Fig.2
t1
LS
d1
t5
Fig.1
LS
I5
aTable 1 Bolt Grip Taper (Fig.1)

Bearing
Number
BT35
BT40
BT45
BT50
BT60
DF_2
t1
t2
t3
t5
53
43
20
10
13.0
38.1
13
56.5
M121.75
21.62
63
53
25
10
16.6
44.45
17
65.4
M162
25.3
85
73
30
12
21.2
57.15
21
82.8
M2025
33.1
DF
d1
d3
LS
CRKS
d5
100
85
35
15
23.2
69.85
25
101.8
M243
40.1
155
135
45
20
28.2
107.95
31
161.8
M303.5
60.7
LS
I1
I2
I3
d3
aTable 2 National Taper (Fig.2)

d2
CRKS
Metric
Wit
Screw
Screw
I4
DF
I5
31.75
17.4
70
50
M12
W 1/2
24
50
16.5
50
44.45
25.3
95
67
M16
W 5/8
30
70
24
63
10
69.85
39.6
130
105
M24
W1
45
90
38
11
100
13
107.95
60.2
210
165
M30
W 11/4
56
110
58
12
170
15
BD
d1
M.T.NO.
60
I1
LS
Morse Taper
(Shank with Screw)
Fig.4
d2
M.T.NO.
R
BD
Morse Taper
(Shank with Tongue)
d1
d2
Fig.3
NT30
NT40
NT50
NT60
d1
Bearing
Number
CRKS
I1
LS
818
aTable 3 Shank with Tongue (Fig.3)

Morse Taper
Number
0
1
2
3
4
5
d1
9.045
BD
9.201
d2
6.104
I1
LS
56.5
59.5
3.9
6.5
8.5
10.5
12.065
3.5
12.240
8.972
8.7
62.0
65.5
5.2
13.5
1.2
17.780
18.030
14.034
13.5
75.0
80.0
6.3
10
16
1.6
23.825
24.076
19.107
18.5
94.0
99
7.9
13
20
31.267
6.5
31.605
25.164
24.5
117.5
124
11.9
16
24
2.5
44.399
6.5
44.741
36.531
35.7
149.5
156
15.9
19
29
10
63.348
63.765
52.399
51.0
210.0
218
19
27
40
13
83.058
10
83.578
68.185
66.8
286.0
296
28.6
35
54
19
CRKS
TECHNICAL DATA
aTable 4 Shank with Screw (Fig.4)
Q042
Morse Taper
Number
0
1
2
3
4
5
6
7
d1
9.045
BD
d2
I1
LS
9.201
6.442
50
53
0.2
12.065
3.5
12.240
9.396
53.5
57
0.2
M6
16
17.780
18.030
14.583
14
64
69
0.2
M10
24
23.825
24.076
19.759
19
81
86
0.6
M12
28
31.267
6.5
31.605
25.943
25
102.5
109
1.0
M16
32
44.399
6.5
44.741
37.584
35.7
129.5
136
2.5
M20
40
63.348
63.765
53.859
51
182
190
12
4.0
M24
50
83.058
10
83.578
70.052
65
250
260
18.5
5.0
M33
80
INTERNATIONAL SYSTEM OF UNITS

y UNIT CONVERSION TABLE for EASIER CHANGE into SI UNITS
(Bold type Indicates SI unit)
a Pressure
Pa
kPa
MPa
bar
kgf/cm2
atm
mmH2O
mmHg or Torr
110-3
110-6
110-5
1.0197210-5
9.8692310-6
1.0197210-1
7.5006210-3
1103
110-3
110-2
1.0197210-2
9.8692310-3
1.01972102
7.50062
1106
1103
110
1.0197210
9.86923
1.01972105
7.50062103
1105
1102
110-1
1.01972
9.8692310-1
1.01972104
7.50062102
9.6784110-1
1104
7.35559102
1.03323104
7.60000102
9.80665104
9.8066510
9.8066510-2
1.01325105
1.01325102
1.0132510-1
1.01325
9.80665
9.8066510-3
9.8066510-6
9.8066510-5
110-4
9.6784110-5
1.33322102
1.3332210-1
1.3332210-4
1.3332210-3
1.3595110-3
1.3157910-3
(Note) 1Pa=1N/m
9.8066510-1
1.03323
1
1.3595110
7.3555910-2
1
a Force
a Stress
Pa
MPa or N/mm2
kgf/mm2
kgf/cm2
1105
1.0197210-1
110-6
1.0197210-7
1.0197210-5
110-5
1.0197210-6
1106
1.0197210-1
1.0197210
9.80665106
9.80665
1102
9.80665104
9.8066510-2
110-2
dyn
kgf
9.80665105
9.80665
(Note) 1Pa=1N/m2
a Power (Rate of Production / Motive Power) /Heat Flow Rate
1
3.600
106
kW h
kgf m
kcal
2.7777810-7
1.0197210-1
2.3888910-4
3.67098105
8.6000 102
9.80665
9.80665
2.7240710-6
4.18605103
1.1627910-3
1
4.26858102
(Note) 1J=1Ws, 1J=1N m

1cal=4.18605J
(By the law of weights and measures)
2.3427010-3
1
7.355
1.16279
kgf m/s
PS
kcal/h
1.0197210-1
1.3596210-3
8.6000 10-1
1.3333310-2
1
102
7.5
10
1.1857210-1
1
1.5809510-3
8.43371
6.32529102
1
(Note) 1W=1J/s, PS:French horse power

1PS=0.7355kW
(By the enforcement act for the law of weights and measures)
1cal=4.18605J
TECHNICAL DATA
a Work / Energy / Quantity of Heat
Q043
TECHNICAL DATA
TOOL WEAR AND DAMAGE

CAUSES AND COUNTERMEASURES
Tool Damage Form
Cause
Tool grade is too soft.
Flank Wear
Cutting speed is too high.

Flank angle is too small.
Feed rate is extremely low.
Crater Wear
Chipping
Fracture
Plastic
Deformation

Feed rate is too high.
Tool grade is too hard.
Lack of cutting edge strength.
Lack of shank or holder rigidity.
Lack of cutting edge strength.
Lack of shank or holder rigidity.
Depth of cut and feed rate are
too large.
Cutting temperature is high.
Cutting speed is low.
Welding
Thermal Cracks
Poor sharpness.
Unsuitable grade.
Tool grade with high wear

resistance.
Lower cutting speed.
Lower feed rate.
Tool grade with high toughness.
Lower feed rate.
Increase honing.
(Round honing is to be changed
to chamfer honing.)
Use large shank size.
Lower feed rate.
Increase honing.
(Round honing is to be changed
to chamfer honing.)
Use large shank size.
Tool grade with high wear resistance.
Decrease depth of cut and feed rate.
Tool grade with high thermal
conductivity.
(For JIS S45C, cutting speed 80m/min.)
Increase rake angle.
Tool grade with low affinity.
(Coated grade, cermet grade)
Hard surfaces such as uncut

surfaces, chilled parts and
machining hardened layer.
Friction caused by jagged shape
chips. (Caused by small vibration)

resistance.
Flaking
Cutting edge welding and

adhesion.
Poor chip disposal.
Increase rake angle to improve

sharpness.
Enlarge chip pocket.
Flank Wear
Fracture
Damage due to the lack of

strength of a curved cutting edge.
Increase honing.

Cutting resistance is too high and
causes high cutting heat.
Decrease honing.
Tool grade with high wear resistance.
Notching
TECHNICAL DATA

resistance.
Increase flank angle.
Increase feed rate.
Expansion or shrinkage due to cutting Dry cutting.

(For wet cutting, flood workpiece
heat.
with cutting fluid)
Especially in milling.
Increase rake angle to improve

sharpness.
for
* Damage
polycrystallines
Crater Wear
Fracture
for
* Damage
polycrystallines
Q044
Countermeasure
CUTTING TOOL MATERIALS

The table below shows the relationship between various tool materials, in relation with hardness on a vertical axis
and toughness on a horizontal axis. Today, cemented carbide, coated carbide and TiC-TiN-based cermet are key
tool materials in the market. This is because they have the best balance of hardness and toughness.
Diamond Coating
Sintered Diamond
Sintered CBN
Si3N4
Hardness
Ceramics
Coated Carbide
Al2O3
Coated Cermet
Coated Micro-grain
Cemented Carbide
Cermet
Micro-grain Cemented Carbide
Cemented Carbide
Coated HSS
Powder HSS
HSS
Toughness
Thermal
Conductivity
(W/mk)
Thermal
Expansion
(x 10-6/k)
Tool Material
Highly Soluble
2100
3.1
Sintered Diamond
1300
4.7
Sintered CBN
1600
100
3.4
Ceramics
Al2O3
2100
-100
i0
29
7.8
Ceramics
Cemented Carbide
TiC
3200
-35
< 0.5
21
7.4
Cermet
Coated Carbide
TiN
2500
-50
29
9.4
Cermet
Coated Carbide
TaC
1800
-40
0.5
21
6.3
Cemented Carbide
WC
2100
-10
5.2
Cemented Carbide
Energy Formation Solubility in Iron

(%.1250r)
(kcal/gatom)
Hard Materials
Hardness
(HV)
Diamond
>9000
CBN
>4500
Si3N4
121
1W/m K=2.3910-3cal/cm secr
TECHNICAL DATA
Q045
TECHNICAL DATA
GRADE CHAIN
P
M
Cemented Carbide
Steel
UTi20T
Stainless Steel
UTi20T
General
K Cast Iron
HTi05T
N Non-Ferrous
HTi10
HTi10
UTi20T
Heat
S Resistant Alloy RT9005 RT9010 MT9015
Ti Alloy
P
Steel
TF15
UE6105 UE6110 MC6015 MY5015 UE6020 MC6025
F7010
MP6120 VP15TF MP6130 VP20RT VP30RT

(PVD)
Coated Carbide
Stainless Steel
M
MC7015 US7020 MC7025 MP7035
General
US735
K Cast Iron
MC5015
UC5105
MC5005
UC5115
F7030
(PVD)
(PVD)
(PVD)
(PVD)
VP15TF MP7130 VP20RT MP7030 MP7140 VP30RT

(PVD)
MY5015
(PVD)
MC5020
(PVD)
(PVD)
VP15TF
For Cutting Tools
(PVD)
N Non-Ferrous
LC15TF
Heat
S Resistant Alloy
Ti Alloy
US905
Hardened
H
Materials
MP8010
P
Cermet
Steel
(PVD)
(PVD)
VP05RT
(PVD)
VP10RT MP9015 VP15TF MP9120 MP9030 MP9130

(PVD)
(PVD)
(PVD)
(PVD)
VP15TF
(PVD)
NX2525 NX3035 NX4545
Stainless Steel
NX2525 NX4545
General
K Cast Iron
NX2525
AP25N
Steel
(PVD)
Coated Cermet
MP9005
Stainless Steel
M
AP25N
General
(PVD)
K Cast Iron
VP25N
(PVD)
MP3025
(PVD)
VP45N
(PVD)
VP25N
(PVD)
AP25N
(PVD)
Non-Ferrous
Non-Metal MD220
(Sintered Diamond)
Sintered Alloy MB4020

Polycrystallines
K Cast Iron
MB710
MB5015
MB730
MBS140
BC5030
(Sintered CBN)
For
Construction
Tools
Q046
Hardened
Materials MBC010 BC8110 MBC020 BC8020 MB8025 MB825
MB835
(Sintered CBN)
Steel
Cast Iron
SF10
MF07
MF10
TF15
MF20
MF30
General Wear
Resistance
GTi05
GTi10
GTi15
GTi20
GTi30
GTi35
GTi40
Corrosion
Resistance
GC15
GC20
GC30
Micro-grain
Cemented Carbide
Special Wear
Resistance
TF15
MF10
MF20S
GM30
Cemented Carbide
General Use
MG10
MG20
MG25
MG30
MG40
MG50
MG60
Micro-grain
Cemented Carbide
For Wear
Resistance
TECHNICAL DATA
Cemented Carbide
(PVD)
(PVD)
GRADES COMPARISON TABLE

CEMENTED CARBIDE
P
ISO
Mitsubishi Sumitomo
Tungaloy
Electric
Symbol Carbide
P01
P10
ST10P
TX10S
P20
UTi20T
ST20E
UX30
P30
UTi20T
A30
UX30
P40
Kyocera
SRT
PW30
ST40E
Turning
Milling
SMA
EX35
SM30
IC54
UMN
WA10B
H10A
EX35
H13A
M30
UTi20T
A30
UX30
DX25
UMS
EX45
H10F
SM30
UM40
EX45
KG03
WH05
K01
HTi05T
H1
H2
TH03
KS05F
K10
HTi10
EH10
EH510
TH10
KW10
GW15
KG10
KT9
WH10
H10
HM
K20
UTi20T
G10E
EH20
EH520
KS15F
KS20
GW25
CR1
KG20
WH20
H13A
K30
UTi20T
N01
HTi10
N30
S01
KW10
EH10
EH510
TH10
KW10
GW15
G10E
EH20
EH520
KS15F
890
HX
883
KU10
K313
K68
KU10
K313
K68
KU10
K313
K68
IC07
IC07
IC08
IC20
IC08
IC20
IC28
IC28
890
IC20
HX
IC20
883
H10
H13A
KT9
WH10
CR1
WH20
KU10
K313
K68
KU10
K313
K68
H15
IC08
IC20
HX
IC08
IC20
H25
RT9005
SW05
KG03
S10
RT9005
RT9010
MT9015
EH10
EH510
KS05F
TH10
SW10
FZ05
KG10
S20
RT9010
TF15
EH20
EH520
KS15F
KS20
SW25
FZ15
KG20
S30
P10
TF15
P20
UTi20T
A30N
UX30
P30
UTi20T
A30N
UX30
H10
H10A
H10F
H13A
K10
K313
K68
HX
IC07
IC08
K10
K313
K68
H25
IC07
IC08
KG30
P40
M10
PW30
PW30
M20
UTi20T
A30N
UX30
M30
UTi20T
A30N
UX30
M40
K01
HTi05T
K10
KU10
K313
K68
KU10
K313
K68
KG30
KS05F
Iscar
IC70
IC50M
IC50M
IC54
EX45
DX25
UMS
N20
EX35
UX30
H1
H2
Seco
Tools
IC70
EH520
U2
G10E
Kennametal
WS10
UTi20T
N10
Mitsubishi
Sandvik
Hitachi Tool
M20
M40
SRT
DX30
SR30
DX30
SR30
EH510
U10E
M10
Dijet
SRT
SRT
DX30
SR30
DX30
SR30
UMN
DX25
UMS
DX25
UMS
EX35
K125M
EX35
GX
IC50M
IC28
IC50M
IC28
IC28
EX45
IC08
IC20
IC08
IC28
IC28
EX35
EX45
SM30
EX45
HTi10
K20
UTi20T
K30
UTi20T
KG03
G10E
G10E
TH10
KS20
KW10
GW25
GW25
KG10
KT9 CR1
KG20
KG30
K115M,K313
K115M
K313
WH10
WH20
H13A
IC20
HX
IC20
TECHNICAL DATA
Classification
(Note) The above table is selected from a publication. We have not obtained approval from each company.
Q047
TECHNICAL DATA

MICRO GRAIN
Classification
Cutting Tools
ISO
Mitsubishi
Carbide
Symbol
Z01
SF10
MF07
MF10
Z10
HTi10
MF20
Z20
TF15
MF30
Z30
Sumitomo
Electric
F0
XF1
F1
AFU
AF0
SF2
AF1
A1
CC
Tungaloy
Kyocera
F
MD05F
MD1508
MD10
MD0508
MD07F
Mitsubishi
Hitachi Tool
Dijet
FZ05
FB05
FB10
FZ10
FZ15
FB15
FZ15
FB15
FB20
FZ20
FB20
FW30
Sandvik
Kennametal
Seco
Tools
NM08
PN90
6UF,H3F
8UF,H6F
NM15
H10F
890
BRM20
EF20N
H15F
890
883
NM25
883
CERMET
Classification
ISO
Mitsubishi Sumitomo
Tungaloy
Electric
Symbol Carbide
P01
P10
P20
Turning
P30
AP25N
VP25N
*
*
T110A
T1000A
NX2525
AP25N
VP25N
T1200A
T2000Z
T1500A
T1500Z
*
*
NX2525
AP25N
VP25N
NX3035
MP3025
MP3025
VP45N
*
*
*
*
*
NS520
AT520
GT520
GT720
NS520
NS730
GT730
NS9530
GT9530
NS530
NS730
GT730
NS9530
GT9530
*
*
*
*
*
T1200A
T2000Z
T3000Z
T1500A
T1500Z
*
*
*
T3000Z *
*
*
*
*
NS520
AT530
GT530
GT720
NX2525
AP25N
VP25N
T110A
T1000A
T2000Z
T1500Z
NX2525
AP25N
VP25N
T1200A
T2000Z
T1500A
T1500Z
NS530
GT730
NS730
NX2525
AP25N
T110A
T1000A
T2000Z
T1500Z
NS710
NS520
AT520
GT520
GT720
K10
NX2525
AP25N
T1200A
T2000Z
T1500A
T1500Z
NS520
GT730
NS730
K20
NX2525
AP25N
P10
NX2525
M10
M20
*
*
*
*
*
*
*
*
*
*
*
*
Kyocera
Dijet
TN30
PV30
TN6010
PV7010
LN10
CX50
TN60
PV60
TN6010
PV7010
CX50
CX75
PX75
TN60
PV60
TN6020
PV7020
PV7025
PV7025
PV90
TN60
PV60
TN6020
PV7020
TN90
TN6020
PV90
PV7020
PV7025
*
*
M30
K
K01
Milling
TECHNICAL DATA
*
*
*
*
*
*
*
T3000Z *
*
*
*
*
T250A
NS530
P30
NX4545
T250A
T4500A
NS530
NS540
NS740
M10
NX2525
M30
NX4545
K01
K10
NX2525
K20
NX2525
TN30
PV30
PV7005
TN6010
PV7010
TN60
PV60
TN6020
PV7020
PV7025
*
*
CT5015
GC1525
CZ25
CH550
GC1525
KT315
KT125
TP1020
TP1030
CM
CMP
IC20N
IC520N
IC530N
KT325
KT1120
KT5020
TP1020
TP1030
IC20N
IC520N
IC30N
IC530N
IC75T
PX90
LN10
CX50
CX50
CX75
*
*
*
*
IC75T
GC1525
KT125
TP1020
TP1030
CM
CMP
CH550
LN10
*
*
LN10
CT5015
KT325
KT125
TN100M
TN60
CX75
CT530
KT530M
HT7
KT605M
CX75
CX90
CX90
CX99
MZ1000
CH550
CH7030
MZ1000
MZ2000
*
*
MZ3000*
C15M
IC30N
C15M
MP1020
IC30N
IC30N
CH7035
TN60
NS530
T250A
Iscar
IC20N
IC520N
TN100M
NS540
NS740
NS530
IC30N
CX75
CX90
CX99
CH550
CH7030
MZ1000
MZ2000
MZ3000
CH7035
*
*
*
CT530
KT530M
HT7
KT605M
TN60
CX75
Coated Cermet
Q048
Seco
Tools
TN60
NX2525
NX2525
*
*
CX75
PX75
PX90
Kennametal
CX75
P20
M20
*
*
*
Mitsubishi
Sandvik
Hitachi Tool
KT530M
HT7
C15M
IC30N
CVD COATED GRADE
Turning
S
P
ISO
Mitsubishi Sumitomo
Tungaloy
Electric
Symbol Carbide
Kyocera
Dijet
Milling
Seco
Tools
Iscar
UE6105
AC810P
AC700G
T9105
T9005
CA510
CA5505
JC110V
HG8010
GC4205
GC4005
KCP05
KC9105
TP0500
TP1500
IC9150
IC8150
IC428
P10
UE6105
MC6015
UE6110
MY5015
AC810P
AC700G
AC820P
AC2000
T9105
T9005
T9115
CA510
CA5505
CA515
CA5515
JC110V
JC215V
HG8010
HG8025
GM8020
KCP10B
KCP10
KCP25
KC9110
TP1500
TP2500
IC9150
IC9015
IC8150
IC8250
P20
MC6015
UE6110
MC6025
UE6020
MY5015
AC820P
AC2000
AC830P
T9115
T9125
CA515
CA5515
CA525
CA5525
CR9025
JC110V
JC215V
HG8025
GM8020
GM25
KCP25B
KCP25
KC9125
TP2500
IC9015
IC8250
IC9025
IC9250
IC8350
P30
MC6025
UE6020
UE6035
UH6400
AC830P
AC630M
T9125
T9135
T9035
CA525
CA5525
CA530
CA5535
CR9025
JC215V
JC325V
GM25
GM8035
GC4315
GC4215
GC4015
GC4325
GC4315
GC4215
GC4015
GC4325
GC4225
GC4025
GC4325
GC4225
GC4025
GC4235
GC4035
KCP30
KCP40
KC8050
TP3500
TP3000
IC8350
IC9250
IC9350
P40
UE6035
UH6400
AC630M
T9135
T9035
CA530
CA5535
JC325V
JC450V
GM8035
GX30
GC4235
GC4035
KCP30
KCP40
KC9140
KC9040
KC9240
KC9245
TP3500
TP3000
IC9350
M10
MC7015
US7020
AC610M
T9115
CA6515
JC110V
GC2015
KCM15
TM2000
M20
MC7015
US7020
MC7025
AC610M
AC6030M
AC630M
T6020
T9125
CA6515
CA6525
JC110V
HG8025
GM25
GC2015
KCM15
KC9225
TM2000
M30
MC7025
US735
AC6030M
AC630M
T6030
CA6525
GM8035
GX30
GC2025
KCM25
KC9230
TM4000
M40
US735
AC6030M
AC630M
GX30
GC2025
KCM35
KC9240
KC9245
TM4000
IC6025
IC9350
K01
MC5005
UC5105
AC405K
AC410K
T5105
CA4505
CA4010
JC050W
JC105V
HX3505
HG3305
GC3205
GC3210
KCK05
TH1500
TK1001
TK1000
IC5005
IC9007
K10
MC5015
UC5115
MY5015
AC405K
AC410K
AC415K
AC420K
AC700G
T5115
CA4515
CA4010
CA4115
JC050W
JC105V
JC110V
HX3515
HG3315
HG8010
GC3205
GC3210
GC3215
KCK15B
KCK15
KCK20
KC9315
TK1001
TK1000
TK2000
TK2001
K20
MC5015
UC5115
UE6110
MY5015
AC415K
AC420K
AC700G
AC820P
T5115
T5125
CA4515
CA4115
CA4120
JC110V
JC215V
HG8025
GM8020
GC3215
KCK20
KC9110
KC9325
TK2001
TK2000
K30
UE6110
AC820P
T5125
JC215
HG8025
GM8020
IC5005
IC5010
IC9150
IC428
IC4028
IC5010
IC8150
IC9150
IC9015
IC418
IC9015
IC418
S01
US905
CA6515
CA6525
CA6535
KC9125
KC9325
IC9250
IC6015
IC8250
IC9250
IC6015
IC9025
IC656
IC9350
IC6025
IC635
S05F
MP1500
MP2500
IC9080
IC4100
IC9015
IC5100
IC520M
MP2500
IC4050
M10
IC9250
M20
KC925M
MP2500
IC520M
IC9350
KC930M
MP2500
IC9350
IC4050
P10
JC730U
P20
F7030
ACP100
T3130
P30
F7030
ACP100
T3130
M30
JC730U
F7030
F7030
ACP100
ACP100
T3130
T3130
CA6535
JC730U
K01
GX2140
GC4220
GX2140
GX2160
GX2030
GX30
GX2160
GC4230
KCPK30
KC930M
GC4240
KC935M
KC530M
GX2140
CA6535
GC2040
KC930M
KC935M
IC635
JC600
K10
MC5020
ACK100
T1115
T1015
K20
MC5020
ACK200
T1115
T1015
K30
MP1500
GX2140
GX2160
GX30
GX2030
GX2160
GX30
M40
Kennametal
P01
P40
Mitsubishi
Sandvik
Hitachi Tool
TECHNICAL DATA
Classification
JC600
JC610
JC610
GX30
GC3220
GC3330
K20W
KC915M
MK1500
MK2000
IC5100
IC9150
GC3330
GC3040
KC920M
KC925M
KCPK30
KC930M
KC935M
MK2000
MK3000
IC4100
IC4050
IC520M
Q049
TECHNICAL DATA

PVD COATED GRADE
Classification
ISO
Mitsubishi Sumitomo
Tungaloy
Electric
Symbol Carbide
P01
P10
VP10MF
AH710
P20
VP10RT
VP20RT
VP15TF
VP20MF
AH710
AH725
AH120
SH730
GH730
GH130
P30
VP10RT
VP20RT
VP15TF
VP20MF
Kyocera
Dijet
Mitsubishi
Sandvik
Hitachi Tool
PR915
PR1005
PR915 PR1005
PR930 PR1025
PR1115 PR1225
PR1425
PR930
PR1025
PR1115
PR1225
Kennametal
Seco
Tools
GC1525
GC1025
KC5010
KC5510
KU10T
CP200
TS2000
IP2000
GC1525
GC1025
GC1125
KC5025
KC5525
KC7215
KC7315
KU25T
CP250
TS2500
IP3000
GC1025
GC1125
KC7015
KC7020
KU25T
KC7235
CP500
KC7040
KC7140
KC7030
CP500
AC520U
AC530U
AH725 AH120
SH730 GH730
GH130 AH740
J740
AH740
J740
P40
AC530U
Turning
M20
M30
M40
VP10RT
VP20RT
VP15TF
VP20MF
VP10RT
VP20RT
VP15TF
VP20MF
MP7035
MP7035
VP10RT
VP20RT
VP15TF
K30
VP10RT
VP20RT
VP15TF
S01
S30
Milling
AC520U
AH710 AH725
PR1025 PR1125 JC5003
AH120 SH730
PR1225
JC5015
GH730 GH130
PR915 PR930 JC8015
GH330 AH630
IP100S
AC520U
AC530U
GH330 AH725
AH120 SH730
PR1125
GH730 GH130
J740 AH645
AC530U
J740
AC510U
K20
S20
TECHNICAL DATA
IP050S
AH710
JC5015
JC8015
GC1005
GC1025
GC1125
GC1105
GC1005
GC1025
GC1125
GC1105
KC5010
KC5510
KC6005
KC6015
KC5025
KC5525
KC7020
KC7025
GC1125
GC2035
KC7030
KC7225
CP250
TS2500
CP500
CP500
IC330 IC354
IC507 IC520
IC570 IC807
IC907 IC3028
IC250 IC330
IC354 IC808
IC908 IC1008
IC1028 IC3028
IC228 IC250
IC328 IC330
IC1008 IC1028
IC3028
IC328
IC928 IC1008
IC1028 IC3028
GC2035
MP9005
VP05RT
MP9005
MP9015
VP10RT
MP9015
MT9015
VP20RT
VP15TF
GH110
PR905
AH110 AH710
GH110
AH110 AH710
PR905
AH725 AH120
GH730 GH130
AH725
AH120
GH730
GH130
KC5010
KC7210
KC7015
KC7215
KC7315
P10
CP200 CP250
TS2000
TS2500
CP250
TS2500
CP500
JC5003 JC8015
AC510U
JC5003
JC5015
JC8015
GC1105
GC1005
GC1025
KC5010
KC5410
KC5510
AC510U
AC520U
AH120
AH725
PR1125
JC5015
JC8015
GC1025
GC1125
KC5025
KC5525
AC520U
AH725
PR1125
ACP200
MP6120
VP15TF
CP500
AH905
JC5003
ACP200
AH725
AH120
GH330
AH330
PR730
PR830
PR1025
PR1225
JC5003
JC5030
JC8015
JC5015
JC5118
PR730
PR830
PR1025
PR1225
PR1230
PR1525
JC5015
JC5030
JC5040
JC6235
JC8015
JC5118
JC6235
CP200
TS2000
CP200
CP250
TS2000
TS2500
KC7225
AH905 SH730
AH110
AH120
P01
P20
IC350
IC1008
IC228 IC350
IC808 IC908
IC1008
IC228 IC350
IC808 IC908
IC1008
IC507 IC907
GC1125
ATH80D
PTH08M
PCA08M
PCS08M
ACS05E
CY9020
GC1010
JX1005 JX1020
GC1025
PC20M JP4020
PCA12M
CY150
CY15
JX1015
GC1025
GC1010
GC2030
Q050
CP200
TS2000
K01
S10
PR915
PR1025
PR1225
PR1425
JC5003
JC8015
VP10MF
K10
IC250 IC350
IC507 IC570
IC807 IC907
IC908
IC228 IC250
IC308 IC328
IC350 IC354
IC507 IC528
IC570 IC807
IC808 IC907
IC908 IC928
IC1008 IC1028
IC3028
IC228 IC250
IC328 IC330
IC354 IC528
IC1008
IC1028 IC3028
IC228 IC328
IC330 IC528
IC1008
IC1028 IC3028
M01
M10
Iscar
KC715M
KC522M
KC525M
F25M
MP3000
IC507
IC903
IC300 IC808
IC908 IC928
IC3028 IC806
IC250 IC350
IC808 IC810
IC900 IC903
IC908 IC910
IC950
IC250 IC300
IC328 IC330
IC350 IC528
IC808 IC810
IC830 IC900
IC908 IC910
IC928 IC950
IC1008
ISO
Mitsubishi Sumitomo
Tungaloy
Electric
Symbol Carbide
P30
MP6120
VP15TF
MP6130
VP30RT
ACP200
ACP300
AH725
AH120
AH130
AH140
GH130
AH730
P40
VP30RT
ACP300
AH140
Milling
JC5015
JC5040
JC8015
JC5118
JC5040
JC5118
PR730
JC5118
PR1025 PR1225
Mitsubishi
Sandvik
Hitachi Tool
JS4045
JS4060
CY250
CY25
HC844
JX1045
PTH30E
JS4060
PTH40H
JX1060
GF30
GX30
PCS08M
CY9020
JX1020
Kennametal
Seco
Tools
GC1010
GC1030
GC2030
KC725M
KC530M
F25M
MP3000
F30M
GC1030
KC735M
F40M
T60M
GC1025
GC1030
KC715M
Iscar
IC250 IC300
IC328 IC330
IC350 IC528
IC830 IC900
IC928 IC950
IC1008
IC903
ACP200
AH725
AH120
GH330
AH330
GH110
PR730
PR660
PR1025
PR1225
JC5015
JC5040
JC5118
JC8015
CY150
CY15
JX1015
GC1025
GC1030
GC1040
GC2030
KC730
KC522M
KC525M
F25M
MP3000
IC250 IC300
IC808 IC830
IC900 IC908
IC928
IC1008
M30
VP15TF
MP7130
MP7030
VP20RT
MP7140
VP30RT
ACP200
ACP300
AH120 AH725
AH130 AH140 PR660
GH130 AH730 PR1510
GH340
JC5015
JC8015
JC8050
JC5118
CY250
CY25
HC844
JM4060
JX1045
GC1040
GC2030
KC725M
KC735M
F30M
F40M
MP3000
IC250 IC300
IC328 IC330
IC830 IC928
IC1008
M40
MP7140
VP30RT
ACP300
AH140
JC5015
JC5118
JC8050
K01
MP8010
AH110
GH110
AH330
JC5003
K10
MP8010
AH110
GH110
AH725
AH120
GH130
AH330
PR1210
PR905
JC5003
JC8015
K20
VP15TF
VP20RT
ACK300
GH130
PR1210
PR905
JC5015
JC5080
JC8015
JC6235
CY150
CY15
PTH13S
JX1015
K30
VP15TF
VP20RT
ACK300
JC5015
JC8015
JC5080
M20
VP15TF
MP7130
MP7030
VP20RT
S01
PR905
S10
MP9120
VP15TF
EH520Z
EH20Z
PR905
S20
MP9120
VP15TF
MP9130
MP9030
EH520Z
EH20Z
ACK300
ACP300
PR905
S30
PR660
PR1230
Dijet
M01
M10
Kyocera
ACP300
H01
MP8010
VP05HT
H10
VP15TF
VP10H
H20
VP15TF
JC5003
JC8015
JC5118
JC5003
JC5015
JC8015
JC5118
JC8015
JC5015
JC8050
JC5118
JC8050
JC5118
JC8003
JC8008
JC8003
JC8008
JC8015
JC5118
JC8015
JC5118
JX1060
GF30
GX30
ATH80D
PTH08M
PCA08M
PCS08M
ASC05E
JX1005
JX1020
CY9020
CY100H
CY10H
F40M
IC350 IC810
IC830 IC900
IC910 IC928
IC950
IC1008
GC1010
KC510M
GC1010
GC1020
KC520M
KC525M
CY250 GX2030
GX30
GC1020
CY25 PTH40H
PTH30E JX1045
KC725M
KC735M
PCS08M
PTH13S
JS1025
C1025
KC510M
IC903
CY100H
CY10H
GC1025
GC2030
S30T
KC522M
KC525M
IC300 IC908
IC808 IC900
IC830 IC928
IC328 IC330
GC2030
KC725M
MK2000
F40M
IC350 IC808
IC810 IC830
IC900 IC908
IC910 IC928
IC950 IC1008
IC350 IC808
IC830 IC908
IC928 IC950
IC1008
IC830 IC928
IC903
BH200
BH250
GC1010
GC1030
KC635M
MH1000
F15M
IC900
ATH80D
PTH08M
PCA08M
JP4005
JX1005
GC1010
GC1030
KC635M
F15M
IC900 IC808
IC908
IC1008
KC530M
MP3000
F30M
IC808 IC908
IC1008
H30
TECHNICAL DATA
Classification
Q051
TECHNICAL DATA

CBN
Classification
ISO
Symbol
Mitsubishi
Carbide
Sumitomo
Electric
Tungaloy
Kyocera
BNC100
BNX10
BN1000
BXM10
BX310
KBN050M
KBN10M
KBN510
BNC160
BNX20
BN2000
BXM20
BX330
KBN25M
KBN525
JBN300
CB7015
CBN010
BXM20
BX360
KBN30M
JBN245
CB7025
CB20
CBN150
CBN160C
H30
BC8110
MBC010
MB810
BC8110
MBC020
BC8020
MB825
MB8025
MBC020
BC8020
MB8025
BC8020
MB835
BXC50
BX380
KBN35M
CB7525
CBN150
CBN160C
S01
MB730
H01
H10
Turning
H20
BNC200
BNX25
BN250
BNC300
BN350
BN700
BN7000
Dijet
Sandvik
Seco
Tools
CBN060K
BX950
CBN170
S10
S20
S30
K01
MB710
MB5015
K10
MB730
MB4020
K20
MB730
MB4020
K30
BC5030
MBS140
Sintered Alloy
BN500
BNC500
BN700
BN7500
BN7000
BN700
BN7000
BX930
BX910
BX850
KBN60M
JBN795
BX950
KBN60M
JBN500
BNS800
BX90S
BXC90
KBN900
MB4020
MB835
BN7500
BN7000
BX450
BX470
BX480
KBN65B
KBN570
KBN65M
KBN70M
Sumitomo
Electric
Tungaloy
CB7525
CBN200
CB7925
CBN300
CBN400C
CBN500
CBN200
Turning
PCD
Classification
ISO
Symbol
Mitsubishi
Carbide
N01
MD205
DA90
N10
N20
MD220
DA150
DX180
DX160
DX140
MD220
DA2200
DX120
N30
MD230
DA1000
DX110
Dijet
Sandvik
KPD001
JDA30
JDA735
CD05
PCD05
CD10
PCD10
KPD010
JDA715
KPD230
JDA10
TECHNICAL DATA
Q052
Seco
Tools
Kyocera
PCD20
PCD30
PCD30M
INSERT CHIP BREAKER

COMPARISON TABLE
NEGATIVE INSERT TYPE
Cutting
Mode
Mitsubishi Sumitomo
Tungaloy Kyocera
Carbide
Electric
PK
Finish
Light
DP
FA
TF
GP, PP
FY
FL
ZF
XP, XP-T, XF
LP
SU
LU
NS, 27
SA, SH
SX, SE
TSF, AS
HQ, CQ
17
XQ, XS
SY
Light
(With Wiper)
SW
PQ
LUW, SEW AFW, ASW
Mitsubishi
Sandvik Kennametal
Hitachi Tool
FE
QF
FF
BE
UR, UA, UT
B, CE
LF , FN
WP, WQ
WL, WF
PG, CJ, GS
CT, AB
PM
TM
PS, HS
PG
AH
QM, XM
MH
GE, UX
DM, 33, 37, 38
PT
UB
AY, AE
Medium
(With Wiper)
MW
GUW
Rough
GH
WMX, WM
PH
MU, MX, ME
TH
UZ
Std.
Std.
PX
GT
HZ, HL
MP
THS
HM, HX
HG, HP
TU
HV
HU, HW, HF
TUS
SH, LM
SU
SS
MS, GM
EX, UP
SA, SF
MS, MU
MM, MA
GU
SM
SU, HU, TK
ES
HM
ST
GH, RM
MU
TH, SH
MF2
Medium
FG
UD
RE
PR, HM
XMR
W-MF2
NF
WS
MF3
MP5
PC, MP
MF5, M3
MT
MN
M5
SM
MW, RW
RN, RP
M6, W-M3
W-MF5
MR6, MR7
NM
WT
RP5
NM6, NM9
RT
GG
UC
HX
QR, PR
MR
R4, R5, R6 NR6, NRF
HR, MR
RM
57, RR6, R7
RH
R8, RR9
NRR
HZ
MF1
NF4
SF
NM4
EM
HE, H
MQ, GU
SF, SZ
MP, AB, BH
MF
PV, DE, SE
MM
AH
QM
SG
FP
LF
MP
MF4
ML
K
AE
RX, RH
HD, HY, HT
VF
MR
UP, RP
M5, MR7
NR4, NR5
RR6
HZ
Finish
Light
NF3, NF4
FW
Heavy
FA
FC
NM, ZM
Medium
FP5
MP3
UG
Finish
Light
FF1, FF2
PF
GU
Heavy
TaeguTec
XF
PF
MA
Std.
Walter
LC
MP
RP
Seco
Tools
01
FH
Light
(Mild Steel)
Medium
Dijet
MP
LK, MA
MK, GK
Std.
Rough
RK
Heavy
Flat Top
Finish
FJ
Light
LS
Medium
MS
Heavy
RS, GJ
MR
CF
UZ, GZ, UX
Flat Top
EF
CM
Std.
Std.
VA, AH
KF
FN
MF2, MF5, M3, M4
MK5
RP,UN
M5
RK5, NM5
PG
V, AE
KM
PH, GC
GG
RE
KR
Flat Top
Flat Top
CH, Flat Top ZS, Flat Top
EG, EX, UP SA, HMM MS, MU, TK
MU
MR3, MR4, MR7
Flat Top
MQ
SU
RK7
SF
SGF
FS, LF
Flat Top
MS
NGP , SM UP, P, NGP
SR, SMR
RP
Flat Top
MF1
MF4, MF5
NF4, NFT
M1
NMS, NMT
M5, MR3, MR4 NRS, NRT
EA
TECHNICAL DATA
ISO
Classification
ET
Peripheral ground type insert.

(Note) Above charts are based on published data and not authorized by each manufacturer.
Q053
TECHNICAL DATA
INSERT CHIP BREAKER

COMPARISON TABLE
7POSITIVE INSERT TYPE
ISO
Classification
Cutting
Mode
Mitsubishi Sumitomo
Tungaloy Kyocera
Carbide
Electric
* *
* *
* *
FP, FV
FP, LU
PF, PSF
GP
LP, SV
SU
PS, PSS
XP
SW
LUW
FC , SC
MV
MP, Std.
MU
UM
GQ , GF
JQ
23
HQ
PM, 24
XQ, GK
FT
JE
MW
FC
Finish
|
Light
FM
LM
SU
Medium
MM, Std.
MU
Medium
JS , 01
Mitsubishi
Sandvik Kennametal
Hitachi Tool
CF , CK
Finish
Light
Medium
(With Wiper)
SMG
Medium
Finish
Light
(With Wiper)
Dijet
LU
MK, Std.
Flat Top
Medium
AZ
Finish
Light
FJ
PF, PSF
PS, PSS
PM
MU, Flat Top Flat Top, CM
AG
AL
* *
* *
AH
*
FF1
F1
FG
WF
FW
W-F1
WS
PS5
PC
PM, UM
MF, MP
F2, MF2, M5
PM5
MT
WM
MW
W-F2
PM
WT
MF
MQ
Flat Top
PF4
TaeguTec
UF, 11
MP
HQ, GK
Walter
LF, FP
PF, UF
CF ,CK
GQ ,GF
LF
Seco
Tools
LF, UF
FP
MM
MP
KF, KM, KR
Flat Top
AL
HP
LF
MQ
FA
F1, F2
F1, M3, M5
AL
PM2
Seco
Tools
Walter
*
*
SA
FL
*
*
HP

11POSITIVE INSERT TYPE

ISO
Classification
Cutting
Mode
Finish
Light
Medium
Mitsubishi Sumitomo
Tungaloy Kyocera
Carbide
Electric
FV, SMG
SV
MV
SI
01
LU
PF, PSF
SU
PS, PSS
MU
GP, CF
HQ
23
XQ
Mitsubishi
Sandvik Kennametal
Hitachi Tool
XP
PM
Dijet
UF
JQ
PF
LF
JE
PM, UM
MF
MP
MF
24
TECHNICAL DATA
Q054
Finish
|
Light
SV
SU
PF, PS
GP, CF
Medium
MV
MU
PM
HQ
MM

TaeguTec
Memo
Memo
Memo
Overseas Sales Offices
MMC METAL FRANCE S.A.R.L. (France)

MMC HARTMETALL GmbH (Germany)
JAPAN
MITSUBISHI MATERIALS CORPORATION

Overseas Sales Dept., Asian Region,
Carbide & Tools Division
KFC bldg., 8F, 1-6-1, Yokoami, Sumida-ku, Tokyo
130-0015 JAPAN
TEL +81-3-5819-8771 FAX +81-3-5819-8774
CHINA
MITSUBISHI MATERIALS (SHANGHAI)

CORPORATION
Room 3911,UNITED PLAZA 1468, Nanjing West Road,
Shanghai, 200040 China
TEL +86-21-62890022 FAX +86-21-62791180
THAILAND
MMC Hardmetal (Thailand) Co., Ltd.

CTI Tower 24th Floor, 191/32 Ratchadapisek Road,
Klongtoey, Klongtoey, Bangkok 10110, Thailand.
TEL +66-2661-8170 FAX +66-2661-8175
INDIA
MMC HARDMETAL INDIA PVT. LTD.

PRASAD ENCLAVE, Site #118/119,
1st Floor Industrial Suburb 2nd Stage, 5th Main,
BBMP Ward #11 Yeshwanthpura Bangalore North
Taluk-560 022, INDIA
TEL +91-80-30807400
MMC HARDMETAL U.K.LTD (United Kingdom)

MMC HARDMETAL POLAND SP.z o.o. (Poland)
MMC HARDMETAL OOO LTD. (Russia)
MMC Hartmetall GmbH Almanya - zmir Merkez ubesi
(Turkey)
TIANJIN TIANLING CARBIDE TOOLS CO. LTD.
TIANJIN LINGYUN TOOL DESIGN CO. LTD.
Norway Sweden Finland
Estonia
(China)
Latvia
MITSUBISHI MATERIALS
Denmark
Netherlands Lithuania Belarus
(SHANGHAI) CORPORATION
TianJin LingYun
Technical Center
(China)
Belgium Czech Slovakia Ukraine
Hungary
(China)
Switzerland Austria
Romania
Shenyang CORPORATION
Slovenia Bulgaria
Beijing
Dalian
Turkey
TSUKUBA PLANT
Greece
Tianjin
Korea
GIFU
PLANT
Delhi ChongqingShanghai
Egypt
AKASHI PLANT
Taipei
Karachi
Kolkata Guangzhou
Machining Technology
Hanoi Hong Kong
MMC ITALIA S.R.L. Mumbai Pune
Center
(Italy)
Chennai
Manila
Bangkok
(Saitama, JAPAN)
Ho Chi Minh
Kuala Lumpur MMC TAISHIN TOOL CO., LTD.
~
Singapore
ESPAN A, S.A.
(Taiwan)
Bangalore
(Espana)
Jakarta
M-VEC (Espana)
USA
MITSUBISHI MATERIALS U.S.A. CORPORATION

11250, Slater Avenue, Fountain Valley, California,
92708, USA
TEL +1-714-352-6100 FAX +1-714-668-1320
P.T.MMC METAL FABRICATION
Johannesburg

(India)
MTEC (Thailand)
Melbourne
Auckland
MMC HARDMETAL (THAILAND) CO., LTD.

(Thailand)
MEXICO
MMC METAL DE MEXICO, S.A. DE C.V.

Av. La Ca~
nada No.16, Parque Industrial Bernardo
Quintana, El Marques, Queretaro C.P. 76246
MEXICO
TEL +52-442-221-61-36 FAX +52-442-221-61-34
MMC TOOLS (THAILAND) CO., LTD.

(Thailand)
BRAZIL
MMC-METAL DO BRASIL LTDA.

Rua Cincinato Braga, 340, 13 Andar, Bela
Vista-CEP 01333-010, So Paulo-SP, BRAZIL
TEL +55-11-3506-5600 FAX +55-11-3506-5688
Delhi
GERMANY
Jamshedpur
Hanoi
Mumbai
MMC HARTMETALL GmbH

Comeniusstr. 2, 40670 Meerbusch GERMANY
TEL +49-2159-91890FAX +49-2159-918966
Pune
Manila
Chennai
UNITED KINGDOM
Bangalore
Coimbatore
MMC HARDMETAL U.K.LTD

5, Galena Close, Amington Heights, Tamworth
Staffs, B77 4AS, U.K.
TEL +44-1827-312312 FAX +44-1827-312314

(India)
Bangkok Ho Chi Minh
Kuala Lumpur
Singapore
FRANCE
MMC METAL FRANCE S.A.R.L.

6, Rue Jacques Monod, 91400, Orsay, FRANCE
TEL +33-1-69-35-53-53 FAX +33-1-69-35-53-50
MMC TOOLS (THAILAND) CO., LTD.

(Thailand)
Jakarta
SPAIN
~
MITSUBISHI MATERIALS ESPAN A,S.A.
Calle Emperador 2, 46136, Museros, Valencia, SPAIN
TEL +34-96-144-1711 FAX +34-96-144-3786
MMC Hardmetal (Thailand) Co.,Ltd.

MMC Hardmetal Thailand Engineering Center
(Thailand)
ITALY
MMC ITALIA S.R.L

Viale delle Industrie 2, 20020 Arese (Mi), ITALY
TEL +39-02-93-77-03-1 FAX +39-02-93-58-90-93
RUSSIA
MMC HARDMETAL LTD.

ul. Bolschaya Semenovskaya 11, bld. 5, 107023
Moscow, RUSSIA
TEL +7-495-72558-85 FAX +7-495-98139-79
POLAND
MMC HARDMETAL POLAND Sp.z o.o.

Al. Armii Krajowej 61, 50-541 Wroclaw, POLAND
TEL +48-71-335-16-20 FAX +48-71-335-16-21
TURKEY
MMC Hartmetall GmbH Almanya - zmir Merkez ubesi

Adalet Mahallesi Anadolu Caddesi No: 41-1 /
15001 35580 Bayrakl/zmir TURKY
TEL +90-232-5015000 FAX +90-232-5015007
South
Africa
Sales Office
Factory
Technical Center
Representative Office
Agency / Distributor
MITSUBISHI MATERIALS U.S.A. CORPORATION
Regional Sales Offices
Los Angeles
MIRACLE TOOLS
AMERICA, LLC
Chicago
Chicago Technical Center (USA)
Toronto

CTI Tower 24th Floor, 191/32 Ratchadapisek Road, Klongtoey, Klongtoey,
Bangkok 10110, Thailand.
TEL +66-2661-8170
FAX +66-2661-8175
Engineering Center and Amata Nakorn Branch

Aamatanakorn Industrial Estate Phase 9 700/843 Moo 5,
Tambon Nongkakha , Amphur Panthong , Chonburi 20160 Thailand
TEL +66-3821-0728
FAX +66-3821-0732
Rayong Branch
RFM Inc.
MMC METAL DE MEXICO,
S.A. DE C.V.
(Mexico)
24/1 Moo 4 ESIE Plaza1, First Floor., unit G6-B and G6-C,
Hemaraj Avenue at the entrance of Eastern Seaboard Industrial Estate (Rayong),
Tambol Pluak Daeng, Amphoe Pluak Daeng, Rayong 21140 Thailand
TEL +66-3895-5658
FAX +66-3895-5659
Singapore Branch
33, Ubi Avenue 3, #05-14 Vertex, Singapore 408868
TEL +65-6634-8250
FAX +65-6634-8257
Columbia
Ecuador
Vietnam Representative Office
Peru
1004, 10th Fl., Giang Vo Lake View Building, D10 Giang Vo, Ba Dinh Dist., Hanoi, Viet Nam
TEL +84-4-3772-8362
FAX +84-4-3772-8299
Bolivia
Ho Chi Minh Representative Office
Chile
1205 on 12th floor, 2A-4A Ton Duc Thang St., Ben Nghe Ward, Dist. 1, HCMC, Vietnam
TEL +84-8-3829-7700
FAX +84-8-3824-3344
Argentina
Indonesia Representative Office

MMC METAL DO BRASIL LTDA.
(Brazil)
Celebration Boulevard Blok AA12 No.19, Grand Wisata, Bekasi Timur Indonesia 17510
TEL +62-21-8261-6353
FAX +62-21-8261-6352
Regional Distributors
ISO 9001 , ISO 14001

)
(JSAQ080) (JSAE036
Australia
METAL CUTTING TECHNOLOGY PTY. LTD.

TEL +61-3-9761-1624
FAX +61-3-9762-9484
Indonesia
PT. Techno Carbide

TEL +62-21-4683-2790
The Scope of the Registration:

Design, development and
manufacturing of metal cutting
tools and blanks of cemented
carbide and other hard materials
FAX +62-21-4683-2791
PT. FUJI PRESISI - TOOL INDONESIA

TEL +62-21-897-0211
FAX +62-21-897-0253
PT. YAMAZEN INDONESIA
TEL +62-21-451-3345
FAX +62-21-451-3346
MITSUBISHI MATERIALS CORPORATION TSUKUBA PLANT (JAPAN)
PT. Kiso-Seiko Indonesia

TEL +62-21-8261-5671
FAX +62-21-8261-5673
PT. Anugerah Toolsindo Mandiri
TEL +62-21-2908-2786
FAX +62-21-2908-2787
ISO 9001 , ISO 14001

(JSAQ094) (JSAE1545)
The Scope of the Registration:
Design, Development, and
Production of Cutting Tools,
Cemented Carbide Blanks,
and Coated Products
PT. KYOSEKI INDONESIA

TEL +62-21-798-9183
FAX +62-21-798-5901
Malaysia
MITSUBISHI MATERIALS CORPORATION GIFU PLANT (JAPAN)
Toolmart Sdn. Bhd.

TEL +60-3-5635-5441
FAX +60-3-5635-4795
KS PRECISION TOOLS (M) SDN. BHD.

TEL +60-3-8941-7168
FAX +60-3-8941-6088
MSR MARKETING SDN BHD.
TEL +60-3-8941-0018
FAX +60-3-8945-0187
Philippines
SHIMEX TRADING, INC.

TEL +63-2-810-2991
FAX +63-2-892-1867
Singapore
JEP INDUSTRADES PTE LTD

TEL +65-6241-2522
FAX +65-6241-2131
Sydney
MSR PTE LTD.

TEL +65-6746-5755
MITSUBISHI MATERIALS CORPORATION AKASHI PLANT (JAPAN)
Adelaide
Melbourne
Auckland
FAX +65-6741-5655
South Africa
MULTITRADE DISTRIBUTORS
TEL +27-11-453-8034
FAX +27-11-453-9696
Thailand
MATERIALS CARBIDE CO.,LTD.

TEL +66-2-370-1599
FAX +66-2-370-1303
Vietnam
NHATMINH Engineering
TEL +84-4-3640-4476
FAX +84-4-3640-4475
YAMAZEN VIET NAM CO., LTD
TEL +84-8-3820-2782
FAX +84-8-5411-0794

CTI Tower 24th Floor, 191/32 Ratchadapisek Road, Klongtoey, Klongtoey,
Bangkok 10110, Thailand.
TEL +66-2661-8170 FAX +66-2661-8175
Engineering Center and Amata Nakorn Branch

Aamatanakorn Industrial Estate Phase 9 700/843 Moo 5,
Tambon Nongkakha , Amphur Panthong , Chonburi 20160 Thailand
TEL +66-3821-0728
FAX +66-3821-0732
Rayong Branch
24/1 Moo 4 ESIE Plaza1, First Floor., unit G6-B and G6-C,
Hemaraj Avenue at the entrance of Eastern Seaboard Industrial Estate (Rayong),
Tambol Pluak Daeng, Amphoe Pluak Daeng, Rayong 21140 Thailand
TEL +66-3895-5658
FAX +66-3895-5659
Singapore Branch
33, Ubi Avenue 3, #05-14 Vertex, Singapore 408868
TEL +65-6634-8250 FAX +65-6634-8257
Vietnam Representative Office

1004, 10th Fl., Giang Vo Lake View Building, D10 Giang Vo, Ba Dinh Dist., Hanoi, Viet Nam
TEL +84-4-3772-8362
FAX +84-4-3772-8299
Ho Chi Minh Representative Office

1205 on 12th floor, 2A-4A Ton Duc Thang St., Ben Nghe Ward, Dist. 1, HCMC, Vietnam
TEL +84-8-3829-7700
FAX +84-8-3824-3344
Indonesia Representative Office

Celebration Boulevard Blok AA12 No.19, Grand Wisata, Bekasi Timur Indonesia 17510
TEL +62-21-8261-6353
FAX +62-21-8261-6352
http://www.mitsubishicarbide.com
EXP-15-E001
2015.4.E (7.5B)

Catalog c007b Full

Enviado por

Dados do documento

Direitos autorais

Formatos disponíveis

Compartilhar este documento

Compartilhar ou incorporar documento

Opções de compartilhamento

Você considera este documento útil?

Este conteúdo é inapropriado?

Direitos autorais:

Formatos disponíveis

Catalog c007b Full

Enviado por

Direitos autorais:

Formatos disponíveis

TURNING TOOLS / ROTATING TOOLS / TOOLING SOLUTIONS

USING THIS CATALOGUE

catalogue is as of April 2015.

note that products in this catalogue are

r : Non stock, produced to order only.

To be replaced by new products.

status is mentioned for the products in this

(Note) Please contact us regarding order numbers and grades

HOW TO USE THIS CATALOGUE

b How to use the block sections.

zTo find the products through the INDEX.

xTo find the series of products from the contents of the

SNppTYPE...SQUARE 90 ............ A105

cTo find the product according to application.

NEGATIVE INSERTS WITHOUT HOLE

CPppTYPE...RHOMBIC 80 ........... A131

SP ppTYPE...SQUARE 90 ............ A140

POSITIVE INSERTS WITHOUT HOLE

RTG TYPE................................. A159

Inside Title for Turning Inserts

a How Text and Index are organized

Cast Iron (< 350MPa)

Cutting Conditions (Guide) :

Heat-resistant Alloy, Titanium Alloy

Cutting Conditions (Guide) :

* Please refer to A028 before using the SW breaker (wiper insert).

: Inventory maintained in Japan.

Index Product Block

Heat-resistant Alloy, Titanium Alloy

Stainless Steel (< 200HB)

Thickness Corner Radius Chip Breaker

Depth of Cut (mm)

Depth of Cut (mm)

Depth of Cut (mm)

CHIP CONTROL RANGE FOR WORK MATERIALS

TURNING INSERTS [NEGATIVE]

CBN & PCD TURNING INSERTS

EXTERNAL TURNING TOOLS

SOLID END MILLS

INDEXABLE HEAD END MILLS

ROTATING TOOL INSERTS

Available database of cutting tools

3. Dimension symbols conforming to ISO 13399

Examples of change in dimensions

*Note 1 See pages 5 to 6 for details.

4. CAD (ISO13399 compliance)

cSTEP data (details, insert assembled model)

vSTEP data (simple model)

2 Download and refer to the "Web CATALOGUE" of PR17

Dimensions and symbols (ISO 13399 compliance)

1 This symbol complies with TS standard or DTS standard of ISO 13399.

Max. depth of cut

Adjusting screw protrusion

What is MIRACLE SIGMA?

Long life & high quality

*Laminated coating (image)

Unique insert minimizes

Double sided Z Geometry

Mitsubishi Materials proprietary double sided,

*NOTE 1. MIRACLE SIGMA products are not given the

Low cutting resistance and double sided insert

Stable Cutting (Continuous cutting, Without scale, etc.)

First recommendation for

Unstable Cutting (Interrupted cutting, With scale, etc.)