Escolar Documentos
Profissional Documentos
Cultura Documentos
74ALS08
Quad 2-Input AND gate
Product specification
IC05 Data Handbook
1991 Feb 08
Philips Semiconductors
Product specification
TYPE
74ALS08
TYPICAL
PROPAGATION DELAY
TYPICAL
SUPPLY CURRENT
(TOTAL)
5.0ns
1.8mA
74ALS08
PIN CONFIGURATION
ORDERING INFORMATION
ORDER CODE
COMMERCIAL RANGE
VCC = 5V 10%,
Tamb = 0C to +70C
DRAWING
NUMBER
74ALS08N
SOT27-1
14-pin plastic SO
74ALS08D
SOT108-1
74ALS08DB
SOT337-1
DESCRIPTION
1A
14 VCC
1B
13 4B
1Y
12 4A
2A
11 4Y
2B
10 3B
2Y
3A
GND
3Y
SC00010
LOAD VALUE
HIGH/LOW
Data inputs
1.0/1.0
20A/0.1mA
Data outputs
20/80
0.4mA/8mA
PINS
DESCRIPTION
nA, nB
nY
NOTE: One (1.0) ALS unit load is defined as: 20A in the High state and 0.1mA in the Low state.
LOGIC SYMBOL
IEC/IEEE SYMBOL
&
3
1
10
12
13
4
6
5
1A 1B 2A 2B 3A 3B 4A 4B
9
8
1Y 2Y 3Y 4Y
10
12
3
11
11
13
VCC = Pin 14
GND = Pin 7
SC00011
SF00053
LOGIC DIAGRAM
1A
1B
2A
2B
3A
3B
4A
VCC = Pin 14
GND = Pin 7
1991 Feb 08
4B
FUNCTION TABLE
1
2
4
5
9
10
12
13
11
INPUTS
1Y
2Y
3Y
OUTPUT
nA
nB
nY
4Y
SC00012
8530857 01670
Philips Semiconductors
Product specification
74ALS08
SYMBOL
RATING
UNIT
VCC
Supply voltage
0.5 to +7.0
VIN
Input voltage
0.5 to +7.0
IIN
Input current
30 to +5
mA
0.5 to VCC
VOUT
IOUT
Tamb
Tstg
16
mA
0 to +70
65 to +150
PARAMETER
UNIT
MIN
NOM
MAX
5.0
5.5
VCC
Supply voltage
4.5
VIH
2.0
VIL
0.8
IIk
18
mA
IOH
0.4
mA
IOL
mA
+70
Tamb
V
V
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
SYMBOL
LIMITS
TEST CONDITIONS1
PARAMETER
MIN
VOH
VOL
O
VIK
II
IIH
TYP2
UNIT
MAX
VCC 2
IOL = 4mA
0.25
0.40
IOL = 8mA
0.35
0.50
-0.73
-1.5
0.1
mA
20
IIL
-0.1
mA
IO
current3
-112
mA
2.4
mA
ICC
Output
-30
VI = 4.5V
VCC = MAX
1.3
ICCL
VI = 0V
2.2
4.0
mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at VCC = 5V, Tamb = 25C.
3. The output conditions have been chosen to produce a current that closely approximate one half of the true short-circuit output current, IOS.
1991 Feb 08
Philips Semiconductors
Product specification
74ALS08
AC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL
PARAMETER
tPLH
tPHL
Tamb = 0C to +70C
VCC = +5.0V 10%
CL = 50pF, RL = 500
TEST CONDITION
Propagation delay
nA or nB to nY
Waveform 1
MIN
MAX
2.0
3.0
14.0
10.0
UNIT
ns
AC WAVEFORMS
For all waveforms, VM = 1.3V.
nA, nB
VM
VM
tPLH
tPHL
VM
nY
VM
SC00013
CL
RL
AMP (V)
VM
10%
D.U.T.
RT
90%
VM
VOUT
PULSE
GENERATOR
tw
90%
10%
tTHL (tff)
tTLH (tr )
tTLH (tr )
tTHL (tf )
0.3V
AMP (V)
90%
POSITIVE
PULSE
90%
VM
VM
10%
10%
tw
0.3V
DEFINITIONS:
RL = Load resistor;
see AC electrical characteristics for value.
CL = Load capacitance includes jig and probe capacitance;
see AC electrical characteristics for value.
RT = Termination resistance should be equal to ZOUT of
pulse generators.
3.5V
1.3V
Rep.Rate
tw
tTLH
tTHL
1MHz
500ns
2.0ns
2.0ns
SC00005
1991 Feb 08
Philips Semiconductors
Product specification
74ALS08
1991 Feb 08
SOT27-1
Philips Semiconductors
Product specification
74ALS08
1991 Feb 08
SOT108-1
Philips Semiconductors
Product specification
74ALS08
DEFINITIONS
Data Sheet Identification
Product Status
Definition
Objective Specification
Formative or in Design
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
Preliminary Specification
Preproduction Product
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
Product Specification
Full Production
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
LIFE SUPPORT APPLICATIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
Copyright Philips Electronics North America Corporation 1997
All rights reserved. Printed in U.S.A.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 940883409
Telephone 800-234-7381
print code
Document order number:
1991 Feb 08