Escolar Documentos
Profissional Documentos
Cultura Documentos
Frequency
Link Rate
Encryption
VALUE
2.304-2.364 GHz, 2.405-2.470 GHz, 5.00-5.800 GHz
Up to 12 Mbps
128 bit AES / 256 bit AES
MA10-01
MA10-02
MA10-03
MA10-10
MA10-11
MA10-04
MA10-11
MODULE
Classifications of UAVs DGCA regulations Design
INTRODUCTION TO UNMANNED
Consideration of UAV- Environment, Budget & Time,
AERIAL VEHICLE
Airframe Design & Payload
Type of Propulsion Systems Engines & Electric
Propulsion-Navigation & Flight control Systems-Autopilo
SELECTION OF HARDWARE
Systems & Ground control Station-MEMS Sensors used i
sUAV-Inertial Measuring Units(IMU), Gyroscope & GPS
Physical Modelling Approach-State-Space Representation
Determination of Mass and Inertial Characteristics; Centr
of Gravity measurement Knife-Edge Method
DESIGN APPROACH FOR FIXED
determining Iy Bifilar Suspension Method determining
WING AIRCRAFT
Ix, Iz;Determination of Wing Characteristics Calculatio
of Wing Area(S) Calculation of Mean Aerodynamic cho
Calculation of Wing Loading
The Role of Parameterization in Design-Discrete and
Domain Element Parameterizations-NACA Airfoils-Splin
Based Approaches-Partial Differential Equation and Othe
GEOMETRY MODELLING &
Analytical Approaches-Basis Function RepresentationDESIGN PARAMETERIZATION
Morphing-Shape Grammars-Mesh Based Evolutionary
Encodings-CAD Tools vs Dedicated Parameterization
Methods
Strength, stiffness and reliability requirements-Overview
loading actions including: gust and manoeuvre loads,
fatigue, aeroelasticity Limit loads and ultimate loads
UAV STRUCTURAL DESIGN
Wing Structural Details-spars, ribs, skin, stringers-The
flight and gust envelopes-The tail load envelope-Safe life
and fail safe design philosophies, good design practice
The fatigue loading spectrum.
DESIGN AND FABRICATION OF Proto-type design and fabrication of on-going research
FIXED WING UAV
project fixed wing(S-One; RR-Chola-II)
RAPID PROTOTYPING WITH 3D Introduction of 3D Printing Technology-Evolution of 3D
PRINTING
Printing-What is additive manufacturing?-General
procedure of 3D Printing-3D CAD file formats-Stereo
lithography (stl) files-Various Printing technologies (SLA
SLS, FDM, Poly jet printing-Color jet Printing, SHS, SLM
MA11-01
HANDS-ON SESSION OF
AUTOPILOT INTEGRATION
Course Syllabus
S.N
MODULE TITLE
MODULE
Classifications of UAVs DGCA regulations Design
INTRODUCTION TO UNMANNED
Consideration of UAV- Environment, Budget & Time,
AERIAL VEHICLE
Design & Payload
Type of Propulsion Systems Engines & Electric Prop
Navigation & Flight control Systems-Autopilot System
SELECTION OF HARDWARE
Ground control Station-MEMS Sensors used in sUAVMeasuring Units(IMU), Gyroscope & GPS
Physical Modelling Approach-State-Space Representat
Determination of Mass and Inertial Characteristics; Ce
Gravity measurement Knife-Edge Method determin
DESIGN APPROACH FOR FIXED
Bifilar Suspension Method determining Ix, Iz;Determ
WING AIRCRAFT
of Wing Characteristics Calculation of Wing Area(S)
Calculation of Mean Aerodynamic chord Calculation
Loading
Velocities in the body axis, u, v, and w-Rotation rates, p
PROCESSING FLIGHT STATES
r Angle of attack, alpha and sideslip angle, betaDynam
pressure, q Control flaps calibration -Thrust calibratio
THE FLIGHT TEST PROCEDURE Design considerations for selecting input signal- Open-
MA10-01
MA10-02
MA10-03
MA10-04
MA14-01
10
HANDS-ON SESSION OF
AUTOPILOT INTEGRATION
11
MA11-01
12
Diploma Courses