Escolar Documentos
Profissional Documentos
Cultura Documentos
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The content of this users manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this users manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Note: The package contents may be different due to area or your motherboard version.
1
Motherboard Manual
LGA 775
Supports Hyper-Threading / Execute Disable Bit /
Intel Core2Duo / Core2Quad /
Enhanced Intel SpeedStep / Intel Architecture-64 /
CPU Pentium Dual-Core / Celeron Dual-Core /
Extended Memory 64 Technology / Virtualization
Celeron 4xx processor
Technology
(Maximum Watt: 95W)
Intel G41
Chipset
Intel ICH7
Memory 1GB / 2GB / 4GB DDR3 Registered DIMM and ECC DIMM is not supported
Max Memory Capacity 8GB (CPU with FSB 800 MHz only supports DDR3 800)
2
G41D3+/G41D3G+
SPEC
CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)
PS/2 LAN
Mouse Line In/
Surround
Line Out
Mic In 1/
Bass/ Center
Since the audio chip supports High Definition Audio Specification, the function of each audio
jack can be defined by software. The input / output function of each audio jack listed above
represents the default setting. However, when connecting external microphone to the audio port,
please use the Line In (blue) and Mic In (Pink) audio jack.
3
Motherboard Manual
1.5 MOTHERBOARD LAYOUT (G41D3+/G41D3G+ V6.0/6.1)
KBMS1
LGA775
ATXPWR2 ATXPWR1
CPU1
DDR3_A1
DDR3_B1
VGA1
JUSBV1 Intel
G41
IDE1
RJ45USB1
BIOS
F_AUDIO1
PEX16_1
LAN
PCI1 SATA4
Super
I/O In tel
PCI2 IC H7
F_USB1
J_PRIN T1 J_COM1
SYS_FAN1
F_USB2
Codec JUSBV2
FDD1 SATA3
4
G41D3+/G41D3G+
1.6 MOTHERBOARD LAYOUT (G41D3+/G41D3G+ V6.2)
KBMS1
LGA775
ATXPWR1
CPU1
ATXPWR2
DDR3_A1
DDR3_B1
VGA1
USB1 C PU_FAN1
JUSBV1 Intel
G41
IDE1
RJ 45USB1
BIOS
AU DIO1
F_AUDIO1
PEX16_1
LAN
PCI1 SATA4
Super
I/O Inte l
PCI2 ICH7
F_USB1
J_COM1
JCMOS1
BAT1 J_PRINT1
SYS_FAN1
JUSBV2
F_USB2
Codec SATA3
5
Motherboard Manual
Special Notice:
Remove Pin Cap before installation, and make good preservation
for future use. When the CPU is removed, cover the Pin Cap on the
empty socket to ensure pin legs wont be damaged.
Pin-Cap
Step 1: Pull the socket locking lever out from the socket and then raise
the lever up to a 90-degree angle.
6
G41D3+/G41D3G+
Step 2: Look for the triangular cut edge on socket, and the golden dot on
CPU should point forwards this triangular cut edge. The CPU will
fit only in the correct orientation.
Step 2-1:
Step 2-2:
Step 3: Hold the CPU down firmly, and then lower the lever to locked
position to complete the installation.
Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it
on the retention frame. Connect the CPU FAN power cable into
the CPU_FAN1. This completes the installation.
7
Motherboard Manual
2.2 FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different due to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
Pin Assignment
1 Ground
2 Power
1 4 3 FAN RPM rate sense
4 Smart Fan Control
Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate sense
Note:
CPU_FAN1 supports 4-pin head connector; SYS_FAN1, 3-pin head one. When
connecting with wires onto connectors, please note that the red wire is the positive and
should be connected to pin#2, and the black wire is Ground and should be connected to
GND.
8
G41D3+/G41D3G+
2.3 INSTALLING SYSTEM MEMORY
A. DDR3 module
DDR3_A1
1. DDR3_B1
Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
9
Motherboard Manual
B. Memory Capacity
Install memory module of the same density in pairs, shown in the table.
The DRAM bus width of the memory module must be the same(x8 or
x16)
10
G41D3+/G41D3G+
2.4 CONNECTORS AND SLOTS
FDD1: Floppy Disk Connector (Only for G41D3+ V6.0/6.1)
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.
2 34
1 33
40 39
2 1
11
Motherboard Manual
PEX16_1
PCI1
PCI2
12
G41D3+/G41D3G+
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1 HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is close, if not, that means the jumper is
open.
PWR_LED
On/Off
++
-
9 16
1 8
+ -
SPK RST
HLED
13
Motherboard Manual
12 24
1 13
2 1
3 4
Pin Assignment
1 +12V
2 +12V
3 Ground
4 Ground
Note:
Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2
connectors have been plugged-in.
14
G41D3+/G41D3G+
Pin Assignment
1 +5V (fused)
2 +5V (fused)
3 USB-
4 USB-
5 USB+
6 USB+
7 Ground
F_USB1
8 Ground
F_USB2
9 Key
2 10
10 NC
1 9
Pin Assignment
1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
10 9 5 Right line in
6 Jack Sense
7 Front Sense
2 1 8 Key
9 Left line in
10 Jack Sense
15
Motherboard Manual
3
1
Pin 2-3 Close:
3 Clear CMOS data.
Pin Assignment
1 Ground
2 TX+
3 TX-
4 Ground
5 RX-
6 RX+
SATA4 7 Ground
SATA3
SATA1 SATA2
1 4 7
16
G41D3+/G41D3G+
1 3
Pin 1-2 close
JUSB V1
1 3
1 3
Pin 2-3 close
JUS BV 2
Pin Assignment
1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground
6 Data set ready
7 Request to send
8 Clear to send
2 10 9 Ring indicator
10 Key
1 9
17
Motherboard Manual
2 26
1 25
18
G41D3+/G41D3G+
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didnt show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html
19
Motherboard Manual
4.2 SOFTWARE
Installing Software
1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.
2. Select Software Installation, and then click on the respective software
title.
3. Follow the on-screen instructions to complete the installation.
Launching Software
After the installation process, you will see the software icon eHOT Line /
BIOS Update appears on the desktop. Double-click the icon to launch the
utility.
eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.
Before you use this utility, please set Outlook Express as your default e-mail client application program.
represents important
*informa ti on that you
This bl ock will show
must provide. Wi thout
this information, you may
the i nformation which *Describe conditi on
of your system.
would be collected in
not be able to send out the mail .
the mail.
If you want to save this information to a .txt file, click Save As and then you
will see a saving dialog appears asking you to enter file name.
We will not share customers data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.
If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web
http://www.biostar.com.tw/app/en-us/about/contact.php for getting
our contact information.
21
Motherboard Manual
BIOS Update
BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.
Update BIOS
with a BIOS file
<Backup BIOS>
22
G41D3+/G41D3G+
<Update BIOS>
Before doing this, please download the proper BIOS file from the website.
For AWARD BIOS, update BIOS procedure
should be run with Clear CMOS function, so
please check on Clear CMOS first.
While the system boots up and the full screen logo shows, press <Delete>
key to enter BIOS setup.
In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.
All the information and content above about the software are subject to be changed
without notice. For better performance, the software is being continuously updated.
The information and pictures described above are for your reference only. The actual
information and settings on board may be slightly different from this manual.
23
Motherboard Manual
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See Close CMOS Header: JCMOS1 section)
2. Wait for seconds.
3. Power on the system again.
24
G41D3+/G41D3G+
BIO-Flasher
BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.
The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.
2. Then, save the BIOS file into a USB pen drive or a floppy disk.
3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.
6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.
z This utility only allows storage device with FAT32/16 format and single
partition.
z Shutting down or resetting the system while updating the BIOS will lead to
system boot failure.
25
Motherboard Manual
26
G41D3+/G41D3G+
4.5 TROUBLESHOOTING
Probable Solution
1. There is no power in the system. 1. Make sure power cable is
Power LED does not shine; the securely plugged in.
fan of the power supply does not 2. Replace cable.
work 3. Contact technical support.
2. Indicator light on keyboard does
not shine.
System is inoperative. Keyboard lights Using even pressure on both ends of
are on, power indicator lights are lit, the DIMM, press down firmly until the
and hard drives are running. module snaps into place.
System does not boot from a hard disk 1. Check cable running from disk to
drive, but can be booted from optical disk controller board. Make sure
drive. both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from an optical 1. Back up data and applications
drive. Hard disks can be read, files.
applications can be used, but system 2. Reformat the hard drive.
fails to boot from a hard disk. Re-install applications and data
using backup disks.
Screen message shows Invalid Review systems equipment. Make sure
Configuration or CMOS Failure. correct information is in setup.
System cannot boot after user installs a 1. Set master/slave jumpers
second hard drive. correctly.
2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
27
Motherboard Manual
APPENDIX: SPEC IN OTHER LANGUAGES
GERMAN
Spezifikationen
LGA 775
Untersttzt Hyper-Threading / Execute Disable Bit /
Intel Core2Duo / Core2Quad /
Enhanced Intel SpeedStep / Intel Architecture-64 /
CPU Pentium Dual-Core / Celeron Dual-Core /
Extended Memory 64 Technology / Virtualization
Celeron 4xx Prozessoren
Technology
(Maximales Watt: 95W)
Intel G41
Chipsatz
Intel ICH7
HD
ALC662 (G41D3+/G41D3G+ V6.0/6.1) Untersttzt High-Definition Audio
Audio-Unters
VT1708B (G41D3+/G41D3G+ V6.2) 5.1-Kanal-Audioausgabe
ttzung
28
G41D3+/G41D3G+
Spezifikationen
PCI-Steckplatz x2
Steckpltze
PCI Express x16 Steckplatz x1
Diskettenlaufwerkanschluss
Jeder Anschluss untersttzt 2 Diskettenlaufwerke
(G41D3+/G41D3G+ V6.0/6.1) x1
Serieller Anschluss x1
System-Lfter-Sockel x1 System-Lfter-Stromversorgungsanschluss
"CMOS lschen"-Sockel x1
Stromanschluss (24-polig) x1
Stromanschluss (4-polig) x1
PS/2-Tastatur x1
PS/2-Maus x1
Rckseiten-E VGA-Anschluss x1
/A LAN-Anschluss x1
USB-Anschluss x4
Audioanschluss x3
29
Motherboard Manual
FRENCH
SPEC
LGA 775
Prend en charge les technologies Hyper-Threading /
Processeurs Intel Core2Duo / Core2Quad
d'excution de bit de dsactivation / Intel SpeedStep
UC / Pentium Dual-Core / Celeron Dual-Core /
optimise/ d'architecture Intel 64 / de mmoire
Celeron 4xx
tendue 64 / de virtualisation
(Watt maximum : 95W)
Intel G41
Chipset
Intel ICH7
Mmoire Chaque DIMM prend en charge des DDR3 Les DIMM registres et DIMM avec code correcteurs
principale de 256Mo / 512Mo / 1Go / 2Go / 4Go d'erreurs ne sont pas prises en charge
Capacit mmoire maximale de 8Go (UC avec FSB 800 MHz ne prend en charge que DDR3
800)
Realtek RTL 8111E (G41D3G+ V6.2) 10 / 100 / 1000 Mb/s ngociation automatique
Prise en
ALC662 (G41D3+/G41D3G+ V6.0/6.1) Prise en charge de l'audio haute dfinition
charge
VT1708B (G41D3+/G41D3G+ V6.2) Sortie audio 5.1 voies
audio HD
30
G41D3+/G41D3G+
SPEC
Fente PCI x2
Fentes
Fente PCI Express x16 x1
Port srie x1
Connecteur Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant
Connecteur d'alimentation x1
(24 broches)
Connecteur d'alimentation x1
(4 broches)
Clavier PS/2 x1
Souris PS/2 x1
E/S du
Port VGA x1
panneau
Port LAN x1
arrire
Port USB x4
Fiche audio x3
Dimensions
182 mm (l) X 235 mm (H)
de la carte
31
Motherboard Manual
ITALIAN
SPECIFICA
LGA 775
Supporto di Hyper-Threading / Execute Disable
Processore Intel Core2Duo /
Bit / Enhanced Intel SpeedStep / Architettura
CPU Core2Quad / Pentium Dual-Core /
Intel 64 / Tecnologia Extended Memory 64 /
Celeron Dual-Core / Celeron 4xx
Tecnologia V irtualization
(Watt massimo: 95W)
Intel G41
Chipset
Intel ICH7
principale / 512MB / 1GB / 2GB / 4GB DIMM registrati e DIMM ECC non sono supportati
Capacit massima della memoria 8GB (CPU con FSB a 800 MHz supporta solo DDR3 800)
Realtek RTL 8111E (G41D3G+ V6.2) Negoziazione automatica 10 / 100 / 1000 Mb/s
32
G41D3+/G41D3G+
SPECIFICA
Alloggio PCI x2
Alloggi
Alloggio PCI Express x16 x1
Connettore floppy
Ciascun connettore supporta 2 unit Floppy
(G41D3+/G41D3G+ V6.0/6.1) x1
Porta seriale x1
Connettore alimentazione x1
(24 pin)
Connettore alimentazione x1
(4 pin)
Tastiera PS/2 x1
Mouse PS/2 x1
I/O
Porta VGA x1
pannello
Porta LAN x1
posteriore
Porta USB x4
Connettore audio x3
i scheda (altezza)
33
Motherboard Manual
SPANISH
Especificacin
LGA 775
Admite Hyper-Threading / Bit de deshabilitacin de
Procesador Intel Core2Duo / Core2Quad /
ejecucin / Intel SpeedStep Mejorado / Intel
CPU Pentium Dual-Core / Celeron Dual-Core /
Architecture-64 / Tecnologa Extended Memory 64 /
Celeron 4xx
Tecnologa de virtualizacin
(Vatio mximo: 95W)
principal 512MB / 1GB / 2GB / 4GB No admite DIMM registrados o DIMM compatibles con
Capacidad mxima de memoria de 8GB ECC (CPU con FSB de 800 MHz slo soporta DDR3 800)
34
G41D3+/G41D3G+
Especificacin
Ranura PCI X2
Ranuras
Ranura PCI Express x16 X1
Puerto serie X1
Conector de alimentacin X1
(24 patillas)
Conector de alimentacin X1
(4 patillas)
Teclado PS/2 X1
Ratn PS/2 X1
Panel
Puerto VGA X1
trasero de
Puerto de red local X1
E/S
Puerto USB X4
Conector de sonido X3
Tamao de
182 mm. (A) X 235 Mm. (H)
la placa
Soporte de
Biostar se reserva el derecho de aadir o retirar el
sistema Windows 2000 / XP / Vista / 7
soporte de cualquier SO con o sin aviso previo.
operativo
35
Motherboard Manual
PORTUGUESE
ESPECIFICAES
LGA 775
CPU / Pentium Dual-Core / Celeron Dual-Core / Disable Bit / Enhanced Intel SpeedStep / Intel
Intel G41
Chipset
Intel ICH7
ITE 8721
Iniciativas para controlo do ambiente
Proporciona as funcionalidades mais
Especifica Monitorizao do hardware
utilizadas em termos da especificao
o Super I/O Controlador/Monitor da velocidade da ventoinha
Super I/O.
Funo "Smart Guardian" da ITE
Interface LPC (Low Pin Count).
Capacidade mxima de memria: 8GB (CPU com FSB 800 MHz s suporta DDR3 800)
Realtek RTL 8111E (G41D3G+ V6.2) Auto negociao de 10 / 100 / 1000 Mb/s
Suporte
definio
36
G41D3+/G41D3G+
ESPECIFICAES
Ranhura PCI x2
Ranhuras
Ranhura PCI Express x16 x1
Porta srie x1
Conector de alimentao x1
(24 pinos)
Conector de alimentao x1
(4 pinos)
Teclado PS/2 x1
Tomada de udio x3
Tamanho
182 mm (L) X 235 mm (A)
da placa
operativos Windows 2000 / XP / Vista / 7 suporte para qualquer sistema operativo com ou sem
37
Motherboard Manual
POLISH
SPEC
LGA 775
Obsuga Hyper-Threading / Execute Disable Bit /
Procesor Intel Core2Duo / Core2Quad /
Enhanced Intel SpeedStep / Intel Architecture-64 /
Procesor Pentium Dual-Core / Celeron Dual-Core /
Extended Memory 64 Technology / Virtualization
Celeron 4xx
Technology
(Maksymalny Watt: 95W)
Intel G41
Chipset
Intel ICH7
gwna 256MB / 512MB / 1GB / 2GB / 4GB Brak obsugi Registered DIMM oraz ECC DIMM
Maks. wielko pamici 8GB (CPU z FSB 800 MHz tylko obsuguje pamici DDR3 800)
Realtek RTL 8103EL (G41D3+ V6.0/6.1) 10 / 100 Mb/s z automatyczn negocjacj szybkoci
Realtek RTL 8105T (G41D3+ V6.2) 10 / 100 Mb/s z automatyczn negocjacj szybkoci
LAN
Realtek RTL 8111DL (G41D3G+ V6.0/6.1) 10 / 100 / 1000 Mb/s z automatyczn negocjacj
38
G41D3+/G41D3G+
SPEC
Gniazdo PCI x2
Gniazda
Gniazdo PCI Express x16 x1
Port szeregowy x1
Klawiatura PS/2 x1
Mysz PS/2 x1
Port USB x4
Gniazdo audio x3
Wymiary
182 mm (S) X 235 mm (W)
pyty
Obsluga
Biostar zastrzega sobie prawo dodawania lub
systemu
Windows 2000 / XP / Vista / 7 odwoywania obsugi dowolnego systemu
operacyjne
operacyjnego bez powiadomienia.
go
39
Motherboard Manual
RUSSIAN
LGA 775
CPU Hyper-Threading / Execute
Intel Core2Duo / Core2Quad /
( Disable Bit / Enhanced Intel SpeedStep / Intel
Pentium Dual-Core / Celeron Dual-Core /
Architecture-64 / Extended Memory 64 Technology /
Celeron 4xx
)
( : 95W)
533 ( G41D3+ V6.1/6.2) / 800 / 1066
FSB
/ 1333
Intel G41
Intel ICH7
DDR3
DDR3 DIMM x 2 DDR3 800/1066/1333(OC)
DIMM
256 / 512 / 1 / 2 / 4 DDR3 DIMM and ECC DIMM
8 ( 800
DDR3 800)
GMA X4500 1984 (
)
ITE 8721
,
Super I/O /
Super I/O.
ITE "Smart Guardian" (
)
"" Ultra DMA 33 / 66 / 100
IDE
PIO 0~4,
3.0 /.
SATA
ATA SATA 2.0.
Realtek RTL 8103EL (G41D3+ V6.0/6.1) 10 / 100 /
Realtek RTL 8105T (G41D3+ V6.2) 10 / 100 /
Realtek RTL 8111DL (G41D3G+ V6.0/6.1) 10 / 100 / 1000 /
Realtek RTL 8111E (G41D3G+ V6.2) 10 / 100 / 1000 /
ALC662 (G41D3+/G41D3G+ V6.0/6.1) High-Definition
VT1708B (G41D3+/G41D3G+ V6.2) 5.1
40
G41D3+/G41D3G+
PCI x2
(
x1 )
x1
CMOS x1
2 USB-
USB- x2
(24 ) x1
(4 ) x1
PS/2 x1
PS/2 x1
VGA x1
LAN x1
- USB- x4
x3
182 () X 235 ()
Biostar
41
Motherboard Manual
ARABIC
LGA 775
Hyper-Threading / Execute Disable Bit /
Intel Core2Duo / Core2Quad /
Enhanced Intel SpeedStep / Intel Architecture-64 /
Pentium Dual-Core / Celeron Dual-Core /
Extended Memory 64 Technology / Virtualization
Celeron 4xx
Technology
): 95 (
Intel G41
Intel ICH7
(800 /1 /2 4
)DDR3 800 8
1984
GMA X4500
( )
:
ITE 8721
Super I/O . Super I/O
Low Pin Count Interface
ITE ""Smart Guardian
/3.0.
Serial ATA SATA
2.0. SATA
42
G41D3+/G41D3G+
2 PCI
PCI Express x16 1
) (G41D3+/G41D3G+ V6.0/6.1 1
IDE 1 IDE
SATA 4 SATA
Smart Fan 1
1 CMOS
USB 2 USB
)24( 1
)4( 1
1 PS/2
1 PS/2
1 VGA /
4 USB
182 )( 235 X )(
Biostar
Windows 2000 / XP / Vista / 7
.
43
Motherboard Manual
JAPANESE
LGA 775
Hyper-Threading / Execute Disable Bit / Enhanced Intel
Intel Core2Duo / Core2Quad /
SpeedStep / Intel Architecture-64 / Extended
CPU Pentium Dual-Core / Celeron Dual-Core /
Memory 64 Technology / Virtualization Technology
Celeron 4xx processor
(: 95W)
Intel G41
Intel ICH7
DDR3
DDR3 DIMM x 2
DDR3 800/1066/1333(OC)
DIMM 256MB / 512MB / 1GB / 2GB /
DIMMECC DIMM
4GB DDR3
(CPUFSB800 MHzDDR3 800
8GB
)
1984MB
GMA X4500
OS
ITE 8721
ITE
3.0 Gb/
SATA ATA
SATA2.0
44
G41D3+/G41D3G+
PCI x2
2
(G41D3+/G41D3G+ V6.0/6.1) x1
x1 1
x1
IDE x1 2IDE
SATA x4 1SATA
x1
x1
CPU x1 CPU()
x1
CMOS x1
2USB
USB x2
(24) x1
(4) x1
PS/2 x1
PS/2 x1
VGA x1
I/O LAN x1
USB x4
x3
182 mm () X 235 mm ()
BiostarOS
OS Windows 2000 / XP / Vista / 7
2011/04/27
45