Escolar Documentos
Profissional Documentos
Cultura Documentos
Resolved CPRs
CAMWorks 2016 SP3
* Please refer to Whats New PDF document for details regarding enhancements in CAMWorks-2016.
1|Page
RESOLVED CPRs DOCUMENT
2|Page
RESOLVED CPRs DOCUMENT
3|Page
RESOLVED CPRs DOCUMENT
4|Page
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
For specific Mill-Turn part, correct C values are not output in
1. CW-62931 11-7990 Post
posted NC code for operations of wrapped features.
When customized TechDB is shared over a network for
11-7601 CAMWorks 2016 SP1 and user links to this TechDB from a
2. CW-57220 TechDB
11-6628 Windows 10 client machine, CAMWorks 2016 SP1 crashes on
opening the TechDB.
Sr. CPR
Help Desk Area
No. Number Description
ID
When a customized TechDB having several tools is used in
1. CW-59664 11-7433 System CAMWorks 2016 SP2, then a delay is seen while opening any
part or assembly.
5|Page
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
The OK, Cancel and Help buttons are not working in Tool
1. CW-58109 11-7008 UI
Select Filter dialog box.
8. CW-57223 ----- Wire EDM In Wire EDM, the posted code for Sodick post is incorrect.
6|Page
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
For Circular Pattern Finish toolpath, simulation displays
CW-56995 11-6537
leftover material for one of the features in the pattern when
14. CW-51294 11-4176 Simulation
'Show Difference' command is used. However, the Step
CW-48245 11-6711
Through command and G-code display correct results.
The Feed rate behavior in F/S tab of Contour Mill operation is
15. CW-56985 11-6529 UI incorrect when user toggles the Defined by option from
Operation to Library or Tool to Library and vice-versa.
For Multiaxis Mill operation, when the Leadin Feedrate value
is edited in the F/S tab, it reverts back to the original value
16. CW-56963 11-6510 Operation
when user switches to another tab of the Operation
Parameters dialog box.
For the specific part, a circular move is not generated in
17. CW-56962 11-6519 Toolpath Contour mill operation for one of the Hole features in the
Hole group feature.
In Tool crib, if user defines a Station number of more than 5
digits, then TechDB accepts that value but if user wishes to
18. CW-56957 11-6509 TechDB
change that number, then TechDB does not allow that and
displays an error message.
Customer has customized their TechDB Hole Mapping table
to be able to select an appropriate thread definition to a
19. CW-56875 11-6462 Operation specific hole diameter for imported solid bodies. This was
working correctly in CAMWorks 2015 but not in CAMWorks
2016.
In XML-based Setup Sheets, description given in Mill Part
20. CW-56800 11-6400 Setup Sheet Setup and Turn Part Setup Properties needs to be made
available in the XML data file.
When CAMWorks 2016 SP1 is used in conjunction with
SOLIDWORKS 2016 SP1, and a multisurface feature is
21. CW-56796 11-6442 System interactively inserted for a specific part, CAMWorks
incorrectly displays a Full/Light Rebuild message. CAMWorks
crashes if user selects the Full or Light Rebuild option.
In German language version of CAMWorks, on the
Leadin/Leadout Tab for all Turning operations, the text string
22. CW-56706 11-6417 Translation label for Leadin Angle and Leadin Amount have got
interchanged. Similarly, the text string for Leadout Angle and
Leadout Amount too has got interchanged.
For the specific mill part, toolpath fails to generate for an
Area Clearance operation with pattern set to Adaptive when
23. CW-56697 11-6413 Toolpath
an Avoid Area is defined. Toolpath generates correctly when
a 'Contain Area' is defined.
7|Page
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
Provide the ability to users to drag and drop a Countersink
24. CW-56696 11-6411 Features thru hole features from one setup to another when the
Setups are on opposite to each other.
When user imports TechDB customized in CAMWorks 2015
version into CAMWorks 2016 version, then invalid tool
25. CW-56881 11-6403 TechDB
cutting parameters (F/S) are observed for non-default Stock
Material groups.
Thread Mill option for Spring Pass creates erroneous
26. CW-56640 11-6362 Toolpath toolpaths when used in conjunction with Taper Angle
function.
In the German language version of CAMWorks 2016, the text
27. CW-56638 11-6368 Translation string 'Full Entry Spiral' within the 'VoluMill Settings' dialog
box is displayed in English.
On posting NC code, values for the post variables
OPR_Z_RAPID_PLANE and OPR_Z_CLEARANCE are
28. CW-56592 11-6343 Post incorrect if Tip offset parameter is used for a User-defined
tool. The value for these post parameters must be adjusted
with the value of tip offset.
For specific Assembly files, when user expands the
CW-56585 11-6328
Configuration item in the CAMWorks Operation tree and
CW-56327 11-6174
29. Assembly selected any configuration, the error message Cannot be
CW-51953 11-4402
found or is Read-Only. Unable to change Configuration." Is
CW-47585 11-2533
displayed.
Hole thread mapping for countersink holes is not working in
30. CW-56531 11-6298 Features CAMWorks 2016 when used with the parameters of the hole
features.
For specific Mill part, the Roughing toolpath (generated for
the Irregular pocket feature defined from a sketch) leaves
31. CW-56530 11-6297 Toolpath
material in the center if allowance is set to 0 with stepover
of 50%.
For the specific turn part, the Turn Rough toolpath gouges
32. CW-56505 11-6280 Toolpath
the part.
For through hole features the Countersink machining depth is
33. CW-56484 11-6225 Operation truncated to the value of feature depth even though a larger
value is defined in TechDB.
For the specific part the Contour Mill toolpath cannot be
34. CW-56481 11-6259 Toolpath
generated correctly.
With German OS and German MS Access, the data importing
35. CW-56469 11-6195 TechDB does not work in TechDB. Some of the machines do not get
imported.
8|Page
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
For specific Mil part, the Contour Mill toolpath does not
machine the pocket feature completely and leaves material in
36. CW-56412 11-6210 Toolpath
the center of the feature. This behavior is observed when
side allowance has a negative value with Stepover of 50%.
In Chinese version of CAMWorks, in Contour tab of Contour
37. CW-56387 11-5613 Translation Mill operation, the translation of the string OFF in Ramp
dropdown list is incorrect.
Create new post Parameter HAVE_COORDINATE_SYS to find
38. CW-56385 11-6126 Post
out if user has selected a FCS in the Main setup.
9|Page
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
In XML data file, SOLIDWORKS Configuration Specific data
48. CW-56119 11-6105 Setup Sheet
from the Evaluated Value column is missing.
For the specific Mill part, the Contour Mill toolpath for rest
49. CW-56113 11-6130 Toolpath machining with specific Cut diameter and flagged as Override
previous doesnt machine the feature consistently.
For specific mill part, the thread mill toolpath for Hole Group
feature containing multiple passes with Previous allowance
50. CW-56111 11-6137 Toolpath
goes to a Rapid plane for every pass at the last hole of the
Hole Group feature.
In XML-based Setup Sheets, certain 3 Axis operation
51. CW-56051 ---- Setup Sheet parameters and stock parameters need to be made available
in the XML data file.
For specific part, the Center Drill and Drill toolpaths gouge
52. CW-56038 11-6128 Feature the top face of the part because of hole group feature
recognition in incorrect setup.
For the specific part the rapid links in a Contour mill
53. CW-56012 11-6111 Toolpath operation with side passes are incorrect. This used to work
satisfactorily in CAMWorks 2015.
10 | P a g e
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
The Final Feedrate option parameter value is not getting
applied to the Contour Mill toolpath. The option is found
60. CW-55675 11-5936 Toolpath
under the Contour tab of the Contour Mill operation within
the Settings... option.
The full form for SFM in the CAMWorks Help file for Tool
61. CW-55667 11-5934 Help cutting parameters (new spindle speed addition to 2016) is
spelled incorrectly.
While selecting Rolling Tap Tool Assembly in TechDB, an error
message is encountered, which is not at all required. The Tool
62. CW-55662 11-5917 TechDB
summary too doesnt get updated on the basis of the tool
assembly selection.
11 | P a g e
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
In XML-based Setup Sheets, information of how the user has
72. CW-55252 11-5669 Setup Sheet assigned the Define tool diameter and Length Offset needs
to be made available in the XML data file.
In Chinese version of CAMWorks, in the Facing tab of Face
73. CW-55247 11-5176 Translation Mill operation, the term Machining to has been incorrectly
translated in Chinese.
For specific part, the Contour Mill toolpath that was
74. CW-55189 11-5656 Toolpath generated for the Part Perimeter feature with Toolpath
center set to without Compensation gouges the part.
In TechDB, the Inch Turn Thread Conditions form has Main
75. CW-55155 11-5648 TechDB Spindle attributes assigned to operations that should actually
be Sub-Spindle.
For specific Mill part, the Contour Mill toolpath gouges the
76. CW-55152 11-5641 Toolpath
island in the defined feature.
If a VoluMill toolpath is generated using a Machine definition
with high feed rate capabilities and later an alternate
77. CW-55045 11-5582 Operation machine with lower feed rate is selected, then on attempting
to edit VoluMill parameters, an error message will be
displayed and CAMWorks crashes.
In TechDB, if the default values for Multiaxis Mill operations
have been modified and user navigates to the Features and
78. CW-55043 11-5547 TechDB
Operation form and executes Load Defaults command, then
an error message is observed and defaults are not loaded.
12 | P a g e
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
For Rough Mill operations, when the Entry method is set to
83. CW-54778 11-5453 Toolpath Ramp, then the Ramp Entry move does not retain the
selected Cut Method (Climb/Conventional).
When NC code is generated for specific Wire EDM toolpath,
84. CW-54734 11-5439 Wire EDM the resultant NC code causes a machine error which is related
to the start and end points not aligning.
For specific Mill part file, the Contour Mill Operation
85. CW-54708 11-5431 Toolpath generated for Irregular Slot Feature with External Corners
option set to Rounded gouges the part.
For VoluMill toolpath with Pre-drilled entry method, the drill
tip length is not being added by default to the through
86. CW-54634 21047 Toolpath feature. This needs to be done by manually by the user. The
spiral entry method for Pre-Drilled entry method is incorrect.
The correct method is Plunge.
In the Machine tab of Machine node, the dropdown fields for
87. CW-54568 20993 Operation
"Simulation machine" and "Simulation controller" are empty.
For the specific part CAMWorks fails to recognize the slot
88. CW-54175 11-5184 Features
feature when recognize Hole feature in set to ON.
In Turn module, when rebuild is done after modifying the part
then, the associated features are placed after the cut off
89. CW-54150 11-5164 Rebuild
operation in the same setup. However in Milling, the
operations are listed in correct order.
During simulation of Turn operation, CAMWorks crashes
during simulation of Thread Machining. This is observed only
90. CW-54074 11-5139 Simulation
when a solid part is declared as stock. Simulation works
correctly with STL files.
For specific Mill part, when simulation is done on the
CW-54044 11-5129
91. Simulation toolpath for the patterned feature, then the simulation
CW-34812 10-6609
happens in reverse for the third instance.
For multiaxis operation, the tilt lines selected in the Tilt axis
92. CW-53863 18815 UI tab of the Operation Parameters dialog should be highlighted
in the graphics area.
For specific part, toolpaths cannot be generated for Bore
93. CW-53756 15601 Toolpath Rough and Bore Finish operations when holder orientation is
"Left down".
In Wire EDM mode, for the specific part, when you move the
94. CW-53623 15211 Wire EDM last operation to the top of the Operation tree, the associated
toolpath changes.
13 | P a g e
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
In Mill-Turn mode, when Turn Setups and Mill Setups are
95. CW-53031 11-4861 Post selected and post processed, then only the toolpaths of Turn
Setups are post processed and not that of Mill Part Setups.
User needs the steps to be followed in order to select and
96. CW-52266 11-4657 API Help highlight the Faces of Multi Surface Feature using CAMWorks
API.
For specific part, for the turn finish operation with layered
97. CW-52030 114603 Toolpath option, the tool does not go to the defined retract value after
each cut.
API to create Multi Surface Feature as an Avoid Feature in
98. CW-51759 11-4444 API
CAMWorks
If Save Operation Plan command is executed for a
multisurface feature for which an Area Clearance operation
99. CW-51701 11-4448 Operation
was defined (with Adaptive pattern and Opt Stepover value),
then it does not save the Stepover value correctly.
In CAMWorks Options, the default for Apply to: parameter
100. CW-51597 11-4367 System
must be set to 'All Possible'.
In General tab of CAMWorks Options, if the Show node
description option is enabled, the description for the tree
101. CW-51585 11-4351 UI items are not shown if the Show node Description
command in the CAMWorks NC Manager context menu is
disabled.
In the default TechDB, some of the Operation Parameters for
102. CW-51452 11-4281 TechDB
Thread Mill operation are incorrect.
In Mill-Turn mode, for Multi Point thread mill operations,
multiple settings the NC tab are incorrect. The Rapid Plane
103. CW-51451 11-4281 Operation G98 and clearance Plane G99 must be inactive and
Polar/Cylindrical Interpolation checkbox must be active when
Rotary Axis mode is set to Free.
The Combine Operation command does not work properly
104. CW-51350 11-4230 Wire EDM in Wire EDM mode. Toolpaths do not get generated for all
selected features.
In XML-based Setup Sheets, the Tool Parameter 'Shoulder
105. CW-50782 11-4089 Setup Sheet
Length' needs to be provided in the XML data file.
In Mill-Turn module, the Estimate time for a toolpath
11-3778
106. CW-50334 Operation machining all the instances in a pattern is same as machining
11-5806
a single instance.
CW-50190 11-3739 For specific part with patterned feature, the Thread Mill
CW-46711 11-2158 toolpath simulation does not match the Step through
107. Simulation
CW-40555 11-2641 toolpath simulation. The tool moves in reverse direction w.r.t.
CW-25081 11-4399 the toolpath.
14 | P a g e
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
11-4601
11-4606
10-9427
Beta-512
In Wire EDM mode, the CAMWorks tooltip display does not
108. CW-49555 11-3598 Wire EDM properly convert the parametric values when switching the
part units between Inch & Metric units.
There is no post parameter that specifies number of thread
109. CW-49530 11-3578 Post passes. Create a new post parameter
QUERY_NUM_THREAD_PASSES for this purpose.
In XML-based Setup Sheets, custom SOLIDWORKS property
110. CW-49527 11-3540 Setup Sheet
names need to be provided in XML data file.
For specific part with Contour Mill toolpath generated for
patterned feature, when Simulation command is run, the
111. CW-49302 10-9427 Simulation
simulation is correct during first instance but gets reversed by
180 degrees during the second instance.
While interactively inserting a new operation, if a new feature
is created for the current operation using the command
Beta2015- available in the Insert Operation dialog box, then this newly
112. CW-47389 UI
US added feature must be automatically selected as the feature
for which operation is to be inserted in the Insert Operation
dialog box.
The user-defined Mill and Turn tools in TechDB have incorrect
file location viz. CAMWorks2001 for metric and
Beta2015-
113. CW-47355 TechDB CAMWorks2005 for inch. The folder names needs to be
US
updated and made consistent and folder location must point
to the correct folder.
For the specific Mill part, the Leadin point for Contour Mill
operation generated for Part Perimeter-Open Pocket feature
114. CW-47346 11-5855 Operation
cannot be moved to a different point, but it can be moved if
the feature type is Boss.
To maintain consistency the command icon in the Manage
Beta2015-
115. CW-46775 UI Stock dialog box for using a SOLIDWORKS part as stock
EMEA
should be identical in both Part mode and Assembly mode.
In Assembly mode, if Setups and features are interactively
116. CW-45801 11-1697 Assembly inserted from Operation tree, then CAMWorks doesnt allow
interactive insertion of operations for the features.
In TechDB UI, provide an option to insert thread mill
117. CW-45685 ----- TechDB operation for counterbore holes. The option is currently
available only in CAMWorks UI.
15 | P a g e
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
When user tries to save a specific part file for which
118. CW-44845 11-1163 System operations and toolpaths have been generated for large
complex surfaces, CAMWorks crashes.
The Area Clearance operation with Pattern type set to
119. CW-44613 11-0962 Toolpath
VoluMill doesnt consider the negative value for Allowance.
The Z Level Operation generated from TechDB doesnt retain
the value of the check box for combination cycle. The check
CW-44384 11-0782
120. Operation box is set to false even though the value is set to true in
CW-43863 11-0789
TechDB. When user does Save Operation Plan, then the same
value is not saved into TechDB.
For specific part, the simulation of Contour Mill toolpath with
121. CW-41236 Beta-2014 Simulation amp set to Angle or Cut amount is incorrect. However, the
step through simulation is correct.
In Mill mode with IPS units, the max feedrate that a user can
assign to a Sub Spindle operation is 39.39 inches (which is
122. CW-39661 10-8976 UI approx. 1000mm). The text displayed in the pop-up warning
message when user tries to assign a higher value than
maximum feedrate must be updated for IPS units.
In XML-based Setup Sheets, a provision to add custom images
123. CW-36933 10-7712 Setup Sheet
as required by user must be made.
For specific part, when user edits the inscribed circle value for
124. CW-35805 10-7114 Operation the Diamond Insert tool in the Tool tab of the operation,
CAMWorks/ SOLIDWORKS crashes.
When Contour Mill toolpath is generated for a Circular
patterned hole feature containing two holes and its ramp
CW-34726 10-6564 option is enabled with ramp value equaling the cut
125. Simulation
CW-28226 10-2850 amount/angle, then the toolpath is generated correctly for
both the holes. However, the simulation for the second hole
is not correct.
The Wire EDM post command of EDM_GetTaperAngle()
126. CW-34694 10-6311 Wire EDM
always outputs zero value for the Taper Angle.
16 | P a g e
RESOLVED CPRs DOCUMENT
Sr. CPR
Help Desk Area
No. Number Description
ID
Beta-42 For specific part file, in the Contour Mill toolpath the bottom
129. CW-23891 (User ID: Feature finish parameter are not generated. The toolpath is
3119) generated for a Tapered Pocket feature with islands.
17 | P a g e
RESOLVED CPRs DOCUMENT
18 | P a g e
RESOLVED CPRs DOCUMENT
19 | P a g e
RESOLVED CPRs DOCUMENT
20 | P a g e
RESOLVED CPRs DOCUMENT
21 | P a g e
RESOLVED CPRs DOCUMENT
For 3 Axis and 5 Axis operations, the Fixed/ Free option (which
exists for 2.5 Axis operations) must be made available. This
50. CW-48185 11-2832 Toolpath
will enable the user to output X, C, Z moves instead of X, Y and
Z moves when desired.
An option must be provided in EDM Post system to post a file
51. CW-48183 11-2539 Post
with Line Feed only and no Carriage Return.
When the tree view is split so that there are two trees
displayed and the GoTo command is used, the tree item
55. CW-30248 ----- UI found is always shown in one of the tree views, which may
not be the tree view that GoTo was selected from. This needs
to be rectified.
22 | P a g e
RESOLVED CPRs DOCUMENT
For specific mill part with Open Pocket and pocket features
58. CW-28082 10-2732 Toolpath with islands, it takes approximately 40 to 45 minutes to
generate toolpath.
23 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
Add a new post parameter
TOOL_FLUTE_LENGTH that will fetch the
1. CW-54756 SP0 11-5343 Post
Flute Length of a mill tool from the Mill Tool
Definition tab.
In Japanese version of CAMWorks, within
2. CW-54748 SP0 11-5447 Translation the 2.5 Axis Feature Wizard, the Japanese
text string for Through is incorrect.
24 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
The geometry of the User Defined Mill tool
10. CW-54504 PR1 11-5338 Simulation is incorrectly shown in CAMWorks Virtual
Machine Simulator.
When the Turn operations containing B Axis
value are copied using control and drag
11. CW-54496 PR1 20775 UI functionality, then the user defined B axis
values are not copied in the newly created
operation.
Add more description detail for the Rotary
12. CW-54402 PR1 11-5298 Help Axis - Reverse Direction option in the Help
file.
For the specific part in the Contour Mill
operation if the user selects 'Stay down'
13. CW-54338 PR1 11-5267 Toolpath
option for link between the passes on the
Leadin tab, then CAMWorks crashes.
For the specific part in the Mill Part Setup
on the Origin tab when the origin is defined
14. CW-54319 PR1 20277 UI using a user defined vertex, then the user
will not be able to apply any offsets. This
was working fine in CAMWorks 2014.
When the customized TechDB is imported
15. CW-54301 PR1 11-5255 TechDB into CAMWorks 2015 SP1.2, then some of
the parameters are not imported.
For the specific part in the Turn Rough
operation the estimated time shown when
16. CW-54268 PR1 20213 Operation
spindle mode is set to RPM and SFM is
wrong.
In Chinese version of CAMWorks TechDB, in
the UI for inserting a tool, user defines the
17. CW-54254 SP0 11-5237 Translation Holder Edge as Side or End. The
Chinese text for End needs to be
corrected.
For the specific part when Extract
18. CW-54241 PR1 11-5199 Features Machinable Features is done, then
CAMWorks crashes.
For the specific part on a Rough Mill
operation with entry option set to 'Entry
Drill' CAMWorks generates two entry drill
19. CW-54239 PR1 20157 Toolpath
operations with different drill diameters.
When the user regenerates the toolpath
the entry drill operations become
25 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
satisfactory.
In the New Advanced Approach and Retract
option in NC tab of 2.5 Axis operation for
20. CW-54215 PR1 20025 UI Mill-Turn machines, the retract position is
termed as XYZ Home Absolute Preset. It
should be labeled as XZ Absolute Preset.
Help is not available for "Approach and
21. CW-54194 PR1 20023 Help Retract" dialog box of a Mill operation on a
Mill-Turn machine.
For a Rough Mill operation with pattern
type set to 'Spiral in" the toolpath near an
CW-54189
22. PR1 11-5186 Toolpath island makes the movement in
CW-50261
"Conventional" way even though the cut
method is set as "Climb".
Add API for reversing the direction of
23. CW-54187 PR1 11-5193 API
interactively added Mill Part Setups.
In the specific assembly whenever the user
24. CW-54168 PR1 11-5177 Operation does Edit Definition on any operation,
CAMWorks crashes.
In Chinese version of CAMWorks, in the
dialog box for interactively inserting a Turn
25. CW-54163 SP0 11-5176 Translation feature, the text for Sub Spindle and
Main Spindle in the Spindle dropdown list
needs to be corrected.
The spindle attributes of feature conditions
and matching operation conditions are
26. CW-54108 PR1 Beta TechDB different in default TechDB. This results in
the operations being populated on wrong
setups.
For the 'Area Clearance' operation the
check box value set for use entry holes
27. CW-54012 PR1 19429 UI option is not retained when the Operation
Parameters dialog box is closed and re-
opened.
For the specific part the Z Level toolpath is
28. CW-53994 PR1 19535 Toolpath not machining the defined feature
completely.
In the default TechDB of CAMWorks 2016
the parameter of cutting direction tilt
29. CW-53985 PR1 19359 TechDB
option for Multiaxis Mill operations is
different in Inch and Metric units.
26 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
In Area Clearance operation when the
pattern type is set to VoluMill, then the
30. CW-53968 PR1 19537 Operation
user doesnt have the option of defining the
XY allowance and Z allowance separately.
In Mill mode if a through feature has fillets
on the top face, then the same is not
CW-53964 19465 recognized when Extract Machinable
31. PR1 Features
CW-53717 15389 Features is done. If the feature is of the
blind type, then the fillet at the top face is
recognized.
For the specific part the toolpath for turn
rough operation gets deleted and results
33. CW-53962 SP0 11-5095 Toolpath
into incorrect WIP when variable
allowances are used.
2D sketches should be allowed to be used
32. CW-53944 PR1 19405 Operation
for 5-Axis drilling.
In TechDB, for the hole feature with ID no.
35, the lower range for selecting the tool is
34. CW-53941 PR1 19305 TechDB
to be modified to zero. Strategy is to be
renamed to Drill only.
In CAMWorks 2016, the newly added
functionality of Pre-drilled holes for
VoluMill pattern is available for 2.5 Axis
35. CW-53939 Beta2 19355 Help Rough as well as in 3 Axis Area Clearance
operations. But the CAMWorks Help
documentation states that it is available
only for 2.5 Axis operations.
27 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
In CAMWorks 2016 Beta, CAMWorks error
39. CW-53895 Beta2 19263 UI message is observed when user clicks on
any tab of the Machine node and clicks OK.
When the Ramping Method for the Contour
CW-53859 18983 Mill operation generated for a grouped hole
40. Beta2 Toolpath
CW-53852 11-5057 feature is changed to Angle and
previewed, then CAMWorks crashes.
For the specific turn part the toolpath for
Face Rough operation gets deleted on
41. CW-53788 PR1 15793 Toolpath
executing the Generate toolpath command
in CAMWorks 2016.
In CAMWorks 2016, for all turning
operations, changes done to default values
of any of the parameters in the NC tab are
42. CW-53783 Beta2 15819 Operation not saved when the user performs a
preview and then clicks the button to
expand the Operation Parameters dialog
box.
For the specific turn part, toolpaths were
generated for Rough Groove operation
using user defined tool in CAMWorks 2012.
However, on opening this part file in
43. CW-53772 PR1 15791 Toolpath
CAMWorks 2014, 2015 or 2016 and
executing the Generate Toolpath
command, the toolpath for Rough Groove
operation gets deleted.
The CAMWorks rebuild prompt message is
shown even when the user edits a sketch
44. CW-53755 Beta2 15683 Rebuild
which has not been used to define any
feature in the active part.
If both CAMWorks 2015 and 2016 are
installed, then the
CWEdmMachineSetupTxtToBinx64.exe of
45. CW-53754 Beta2 15687 Wire EDM
CAMWorks 2016 creates the
"MachineSetup.bin" file in the CAMWorks
2015 data folder location.
For the specific part file, if contain area is
defined for the operation to machine
46. CW-53751 PR1 11-5036 Toolpath
grouped features, then an erroneous
toolpath is generated.
47. CW-53696 PR1 11-5019 Toolpath For the specific part the retract move of 3
28 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
Axis Mill undercut operations causes tool to
crash.
For specific part, when the Save Operation
48. CW-53631 Beta2 15403 Operation Plan command is executed, it leads to the
crashing of CAMWorks and SOLIDWORKS.
In the Operation Parameters dialog box for
49. CW-53626 Beta2 15213 UI Multiaxis Mill operation, the text for the
Help button is missing.
If the user inserts a rectangular pocket
feature by selecting multiple faces, then the
50. CW-53619 Beta2 15203 Features inserted feature will be of the type of
irregular pocket and not that of a
rectangular pocket.
When inserting Contour Mill operation, the
Rest Machining parameters are activated
even if the Method is set to None in the
51. CW-53604 Beta2 15183 UI Operation Parameters dialog box for
Contour Mill operation. They get
deactivated only after changing the
method.
Provide functionality to enable using part
faces for defining Open Profile features
52. CW-53601 PR1 15141 Feature
similar to how faces can be used to define
pockets and slots.
In the Insert Operation dialog box, the
selected feature gets deselected when user
53. CW-53599 PR1 15165 UI
changes the type of operation. For
example: From Roughing to Contouring.
For specific part, when user interactively
inserts a pocket feature by picking valid
54. CW-53585 Beta2 15133 Features edges to define its profile, an error message
which states that some of the profiles
selected are invalid is displayed.
When defining an open profile feature, the
user has the ability to select multiple edges.
55. CW-53576 Beta2 11-5000 Features But the user defined 'Tool side' is not
retained when the feature wizard is closed
after defining the features.
For the specific mill part with pocket
feature containing a filleted island, on auto-
56. CW-53568 PR1 15119 Feature detecting the island during interactive
feature insertion, the inner loop of fillet is
considered instead of the outer loop
29 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
resulting in wrong feature.
VoluMill toolpath with Entry method set as
Pre-drilled holes doesnt consider the
57. CW-53560 Beta2 15153 Toolpath
user-defined position of the holes, resulting
in incorrect toolpath.
When user creates slot features using non-
58. CW-53548 Beta2 15113 Features planar entities, then certain material
segments are recognized as air segments.
Increase the size of arrow head that defines
the vector in a New Multiaxis Drilling
59. CW-53482 Beta2 15031 UI operation. Currently, user needs to zoom
on to the arrow in order to view the arrow
head.
The thread mill cycle time calculation for
Countersunk hole pattern considers only
60. CW-53394 PR1 11-4962 Operation
the seed instance and thus the estimated
time will be wrong.
In CAMWorks 2015 SP1.1, it is not possible
61. CW-53384 Beta2 11-4965 TechDB to create a User-defined Boring bar with an
STL File in the TechDB.
Chuck, part and stock orientations are
Machine incorrectly imported into CAMWorks
62. CW-53352 Beta2 11-4945
Simulation Virtual Machine when the Axis of the part is
not parallel to the X Axis of SOLIDWORKS.
In Mill-Turn, when the turn setup origin is
63. CW-53286 Beta1 11-4915 UI set to 'Automatic' then, the origin of the
mill part setup is incorrect.
On Mill-Turn machines, the helical moves of
a Rough Mill toolpath are incorrectly post
64. CW-53043 Beta1 11-4865 Post
process when the Rotary Axis mode is set to
Free.
In Chinese version of CAMWorks, in the F/S
tab of Turn Operation Parameters dialog
65. CW-52890 SP0 11-4828 Translation
box, the translation for mm/min reads as
cm/min.
The posted output of Drill toolpath for a
patterned MS Hole feature shows wrong
indexing angles. However the posted
66. CW-52863 Beta1 11-4793 Post output for Drill toolpath for patterned Hole
feature shows proper indexing angles in the
same setups.
30 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
API to set the origin type of CWOpSetup as
67. CW-52854 SP0 11-4752 API
workpiece corner.
Crash observed when the Save Operation
Plan command is executed for 3 Contour
68. CW-52796 Beta2 11-4801 Operation Mill operations. The crash occurs because
CAMWorks allows the First Cut Amount for
Contour Mill operations to be set to 0.
In CAMWorks 2015 SP1.1, VoluMill toolpath
CW-52780 11-4778 for pocket feature adds extra axial (-Z) pass
69. CW-52625 Beta2 11-4743 VoluMill if the First Cut Amount and Machining
CW-50216 ----- Depth values are more than the Feature
Depth.
For the specific Mill part, the Feed and
70. CW-52776 Beta2 11-4794 Post Speed values posted for the Constant
Stepover operation are incorrect.
CAMWorks generates the threading
toolpath at incorrect location for OD
71. CW-52573 Beta1 11-4744 Toolpath
feature on Sub-Spindle with Program point
set to Tool Nose center.
In Mill module the fillets at the top face of
the pocket feature are not recognized when
72. CW-52558 PR1 11-4738 Feature Extract Machinable Features is done. This
happens when the pocket feature is
intersected by another feature.
When post processing using the M3Axis-
Tutorial post using the step by step option,
72. CW-52393 SP0 11-4669 Post
the system created *.sub file gets locked
and can't be deleted.
In CAMWorks German version, in Turn and
Mill-Turn mode, in the Setup tab of the
74. CW-52335 SP0 11-4692 Translation
Machine node, the text for the Display pane
and Options label are incorrectly placed.
When 2012 TechDB is imported is import
into CAMWorks 2015, most of the entries
75. CW-52334 Beta2 11-4681 TechDB
for Cutting Taps are not populated from the
earlier TechDB.
When the machine make is set to
Mitsubishi-FA or Misubishi-FAS then,
76. CW-52324 SP0 11-4684 Wire EDM
CAMWorks fails to generate toolpaths and
results in a crash.
31 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
For the specific part the Contour Mill
toolpath is incorrectly generates when
77. CW-52321 Beta1 11-4665 Toolpath
Calculate safe CNC comp toolpath option
of the Machine dialog box is unchecked.
The TechDB UI displays the message Invalid
78. CW-52317 Beta2 11-4674 TechDB use of null when user selects a Contour
Mill operation in TechDB.
Create 2 new post variables
NEXT_USER_TOOL and
79. CW-52310 Beta2 11-2461 Post
NEXT_USER_TURRET for detecting Tool
change.
For the specific assembly file, when
Leadin/out point of Contour Mill operation
80. CW-52185 PR1 11-4646 Toolpath
is set to Mid-point, the spring pass move is
not generated.
For point to point operations when
parameters are changed and OK button is
81. CW-52146 Beta2 11-4644 Operation pressed, the toolpath does not get updated.
The user will have to Generate Toolpath
again to get the updated toolpath.
For specific mill part with numerous islands
within the open pocket feature, it takes
82. CW-52008 PR1 11-4573 Toolpath
considerable time to generate toolpath for
the Rough Mill operation.
In Mill-Turn module, the generated Post
83. CW-51958 Beta1 11-4545 Post output does not reflects the interactively
inserted feed rate move.
In Turn mode, the point to point (Drill)
operation goes beyond the ID feature limit.
84. CW-51956 Beta2 11-4549 Operation This happens when the ID feature is defined
by the sketch. It works correctly when
feature is defined using Part profile.
In 2.5 Axis Feature: Select Entities dialog
box, the tool tip Next is displayed instead
85. CW-51746 Beta1 11-4454 UI
of End Condition when the user mouse
hover on End Conditions button.
32 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
option enabled and Toolpath Centre set to
as without compensation still remains
compensated with the toolpath radius if
the Calculate safe CNC comp toolpath
option is selected.
For the specific part, on executing the
Extract Machinable Features using
88. CW-51637 PR1 11-4417 Feature
MfgView, the slot feature is incorrectly
recognized.
Toolpath for Rough Mill operation with
Entry Drill/ Entry hole option selected for
89. CW-51619 Beta2 11-4405 Toolpath
entry options changes every time the
Generate Toolpath command is executed.
In TechDB under hole thread mapping, the
user is unable to set the method of "Thread
90. CW-51606 PR1 11-4374 TechDB
Milling" for the hole type of Counter bore
and Countersink.
VoluMill toolpath issue observed when
Negative Z Bottom Allowance is assigned.
91. CW-51330 Beta2 11-4203 VoluMill
The toolpath makes double depth of cut
with the full first cut amount.
On generating XML-based Setup Sheets, the
92. CW-51292 Beta2 ----- Setup Sheet generated images should be stored in a
sub-folder where the XML file is generated.
In Inch mode of TechDB, for all the Mill
Feature operations the tool selection
expression is set with the parameter of
93. CW-51013 PR1 11-3193 TechDB "Box Width". This results in selection of
large tools to machine the feature. The tool
selection expression should be with respect
to "Finish Radius".
11-4498 CAMWorks crashes while generating the
94. CW-50827 Beta1 11-4543 Setup Sheet setup sheets in mill assembly mode if the
11-4737 setup origin is set to 'Part Origin'.
For customized TechDB used by customer,
95. CW-50826 Beta2 11-3983 TechDB tool descriptions are not being displayed in
corresponding fields for Turn Tools.
The positioning of images captures in
96. CW-50629 Beta1 11-3959 Setup Sheet
generated Setup Sheet is incorrect.
33 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
In CAMWorks 2015 SP 1.0, the 3 Axis
VoluMill toolpath doesnt get generated
97. CW-50615 Beta2 11-4056 Toolpath when the Machine Cavities option is
checked. This issue wasnt observed in
CAMWorks 2015 SP0.1.
For the specific part, the Contour Mill
toolpath generated for the irregular pocket
98. CW-50500 PR1 11-3924 Toolpath feature is incorrect when the CNC
compensation is set to ON and the toolpath
center is set to Without Compensation.
In Turn mode, when an operation is
truncated using the Z limits set as "User
99. CW-50369 PR1 11-3853 Operation Defined", then any changes made to the
origin of the turn setup do not update the
user defined limit.
In XML-based Setup Sheet, the
100. CW-50359 SP0 11-3854 Setup Sheet
MchController variable does not work.
In the XML Setup Sheet, the Mill Tool and
Holder image is displayed for a Turn
101. CW-50232 Beta2 11-3764 Setup Sheet Operation when both Mill & Turn
operations are present for the Mill-Turn
Machine.
While machining circular pockets or hole
features with Contour Mill operations with
the combination of CNC compensation set
102. CW-50200 PR1 11-3745 Toolpath to ON and tool path center set to without
compensation, then the tool path is not
generated at the desired position if entry
point is set as "Hole Center".
Using the Mirror Toolpath option with
VoluMill creates an additional mirrored
103. CW-49533 Beta2 11-3589 Toolpath
toolpath that gets overlaid on the correct
mirrored toolpath.
For specific Mill part, the Generate
Toolpath command executed from the
104. CW-49458 Beta2 ----- Toolpath Command Manager and that executed from
the RMB context menu of the operation
generates different results.
34 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
In 3 Axis Flat Area machining, there is no
105. CW-49416 Beta1 11-3496 Toolpath impact of the values given for horizontal
leadin on the toolpath.
In CW 2015 SP SP0, the Contour Mill
toolpath on Part Perimeter feature of the
106. CW-48990 Beta2 11-3329 Toolpath specific part is showing the Incorrect arc
Lead In/Lead Out for 'Start point' with '0'
offset value.
If user unchecks the Equal Step Length
and Equal Step Width and defines several
unique jaw steps and saves the
configuration, then on restarting
107. CW-48940 PR1 11-3300 System
CAMWorks and assigning this chuck
configuration, the Equal Step Length and
Equal Step Width get checked thereby
nullifying all custom jaw settings.
For Setup Sheets, add the Radial (X) and
108. CW-48578 Beta2 11-3117 Setup Sheet Axial (Z) allowance parameters of turn
operations to the XML data file.
The Contour Mill Operation for Rectangular
slot with multiple side passes and Ignore
109. CW-48572 Beta1 11-3098 Toolpath
Air Segments option set to ON, does not
generate correct toolpath.
In TechDB, for Multiaxis Operation
110. CW-48540 PR1 11-3075 TechDB Parameter Definition, the parameter option
'Add Internal Tool Radius' is missing.
For the specific part, the Leadin/ Out point
111. CW-48364 Beta2 11-2975 Toolpath for Contour Mill Toolpath is generated at
the wrong spot for irregular pocket feature.
Add the ability to export the SOLIDWORKS
112. CW-48243 PR1 11-2892 Setup Sheet Configuration Specific information to the
XML-based Setup Sheet.
For parts designed in SOLIDWORKS using
the Cut Extrude feature with Pattern
application or otherwise, on executing the
Extract Machinable Features command,
113. CW-48152 SP0 11-2820 Features the islands within the irregular slot features
are not recognized. For the specific part the
islands within the irregular slot features are
not recognized when Extract Machinable
Features command is executed.
35 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
More time is taken to suppress operations
Beta2015- when selected in numbers of 5 or more in
114. CW-47574 Beta2 UI
US parts or assemblies containing multiple
features and operations.
While post processing the toolpaths if the
center line display is set to ON, then the
Beta2015- toolpaths generated for point to point
115. CW-46848 Beta2 Help
EMEA operations are not highlighted. This needs
to be documented in the CAMWorks Help
file.
Add the ability to create isometric view in
the XML setup sheet with respect to the
116. CW-45792 PR1 11-1689 Setup sheet
origin of each setup present in the mill part
or assembly.
36 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
The multi axis toolpaths fail to generate
when user defined mill holders are used.
123. CW-31152 PR1 10-4822 Toolpath
However 2.5 Axis toolpaths generate
satisfactorily.
The engrave toolpath will include a leadin if
124. CW-30562 Beta1 10-4357 Toolpath
another contour toolpath is generated first.
For Contour Mill operations, when user
defines an Avoid area and sets the toolpath
125. CW-30064 SP0 10-4026 Toolpath Center to Without compensation under
NC tab, then the toolpath always retracts to
Z0 plane to link to the next position.
For the specific part the contour mill
toolpath gouges the part when 'Display
126. CW-28639 PR1 10-3090 Toolpath
cutter compensation on first move' is set to
On.
If the turn setup origin is changed to either
127. CW-27011 PR1 10-2029 Simulation other end or to any other location then the
same doesn't reflect in the simulation.
Add the option of "Direct" on the
Entry/Retract tab of Multi axis mill
128. CW-26888 PR1 10-1960 TechDB
operations in TechDB. The same is present
in CAMWorks.
For the specific part the leadin overlap
129. CW-26700 Beta2 10-1838 Toolpath values defined for Contour mill operation
result in incorrect toolpath.
For the specific part the Contour Mill
130. CW-26038 Beta2 10-1353 Toolpath toolpath gouges the part when the link
between passes is set to 'Stay Down'.
For the specific assembly when we import
part cam data then, the operation data for
131. CW-25935 Beta2 10-1234 Assembly
features in two setups is imported and for
the remaining two setups it is not imported.
For the specific part, Turn features
recognized by AFR are incorrect and
132. CW-25888 Beta2 10-1208 Features
CAMWorks hangs for the time the features
are being recognized.
For Contour Mill operations, if Hole Center
is selected as the Entry Point and Without
133. CW-25829 Beta2 10-1123 Toolpath
Compensation option is enabled, then
CAMWorks offsets the Entry Drill/ Hole too.
37 | P a g e
RESOLVED CPRs DOCUMENT
Fixed in
Sr. CPR CAMWork Help Area Description
No. Number s 2016 Desk ID
Version
10-2083
CW-24493 Provide Tool Crib priority option in Turn
134. Beta1 1-6385 Tool
CW-14490 mode and Mill-Turn mode.
1-6429
When the feature profile of slots feature
are defined using sketches and user has
assigned open air segments, then
135. CW-19851 Beta2 2-0208 Features
CAMWorks must remember the open air
segments which were selected by user even
after the sketch is edited.
38 | P a g e