Escolar Documentos
Profissional Documentos
Cultura Documentos
REPORT
ON
AUTOMATIC INFLATION
OF TIRES
BONAFIDE CERTIFICATE
Certified that this project reportAutomatic inflation of tiresis the bonafide work
and guidance.
Project Guide:-
Er. Jasjevan Singh
Lec.Mechanical Engg.Deptt
SIGNATURE
CONTENTS
1. INTRODUCTION
2. TIRE INFLATION BASICS
3. SELF INFLATING SYSTEMS
4. CENTRAL TIRE INFLATING SYSTEM
5. DESIGN OF MODEL
6. AIR COMPRESSOR
7. PRESSURE SWITCH
8. NON RETURN VALVE
9. AIR SEAL
10.WORKING OF MODEL
11.COST REPORT
12.ADVANTAGES
13.CONCLUSION
14.REFRENCES
ACKNOWLEDGEMENT
We are also indebted to all the teaching and non- teaching staff of the
department of mechanical engineering for their cooperation and suggestions, which
is the spirit behind this project. Last but not the least, we wish to express our
sincere thanks to all my friends for their goodwill and constructive ideas.
Introduction
This project work titled automatic tire inflation system deals with the difficulty in
driving the vehicles with low and high tyre pressure. The irregular and uneven tyre
pressures causes difficulty in driving and even leads to the accidents. This can be
implemented on the vehicles which have air braking system .The project automatic
tyre inflation system is concentrated in maintaining the tyre pressures and thereby
reducing the driving difficulties. This is done by mechanical means and not by
using any sensors and other electronics. The air can be inflated into the tyres
without stopping the vehicle. The air from the air tank is used for inflating the
tyres. The air from the tank is sent to the tyres through a one way valve. The twist
made in the air hose is prevented by a joint. The design of the system is very
simple and also very economical. Therefore it can be implemented easily in the
vehicles. The space requirement for the installation is also very less.
Automatic tire inflation systems can save tire maintenance costs and improve
fuel economy by nearly 1 percent, saving 100 gallons of fuel and eliminating 1
metric ton of greenhouse gas emissions per year. Properly inflated tires also
have fewer punctures and a longer life expectancy.
When not properly inflated, tires flex more under load. This produces heat and
increases rollingresistance, which wastes fuel. Truck tires inflated 10 pounds per
square inch (psi) belowrecommended air pressure levels can reduce truck fuel
economy between 0.5 percent and 1percent. Since the bulk of the load is carried in
the trailer, a 10-psi underinflation in a trailer tiremay have nearly twice the impact
on truck fuel economy as the same amount of underinflationin a drive tire.
Heat and stress from improper inflation softens and deflects tire components,
causing fasterand more uneven wear, which shortens the life of the tire.
Underinflated tires have more frequentpunctures, increasing the risk of tire failures
that could lead to costly road service andloss of revenue.Despite the importance, a
recent survey of combination trucks found that less than half the
tires surveyed were within 5 percent of the recommended inflation pressure.
Another industrysurvey indicates only 8 percent of truck drivers check tire pressure
with a tire gage before eachtrip. One reason fleets may find it difficult to keep tires
properly inflated is because truck tirescan lose up to 2 psi each month, even if the
rim seal and valve stems are tight. A fleet may notbe able to inspect or monitor its
trailer tires regularly due to the fact that extended periods oftime are spent away
from service yards and because trailers are interchangeable. This places
greater responsibility for checking tire pressure onto drivers.
What is the solution?
Automatic tire inflation (ATI) systems monitor and continually adjust the level of
pressurizedair in tires, maintaining proper tire inflation automatically even while
the truck is in motion.One ATI system uses the vehicles own air-brake compressor
to supply air to all the tires. Oncean ATI system is installed, it should not require
any special attention from the drivers. Thiseliminates the need to check tire
pressure manually, which saves time and labor while ensuringconsistent and proper
tire inflation.
Automatic Air Inflation System
Tire-Inflation Basics
According to AAA, about 80 percent of the cars on the road are driving with one or
more tires underinflated. Tires lose air through normal driving (especially after
hitting pot holes or curbs), permeation and seasonal changes in temperature. They
can lose one or two psi (pounds per square inch) each month in the winter and even
more in the summer. And, you can't tell if they're properly inflated just by looking
at them. You have to use a tire-pressure gauge. Not only is underinflation bad for
your tires, but it's also bad for your gas mileage, affects the way your car handles
and is generally unsafe.
When tires are underinflated, the tread wears more quickly. According to
Goodyear, this equates to 15 percent fewer miles you can drive on them for every
20 percent that they're underinflated. Underinflated tires also overheat more
quickly than properly inflated tires, which causes more tire damage. The faded
areas below indicate areas of excessive tread wear.
Because tires are flexible, they flatten at the bottom when they roll. This contact
patch rebounds to its original shape once it is no longer in contact with the ground.
This rebound creates a wave of motion along with some friction. When there is less
air in the tire, that wave is larger and the friction created is greater -- and friction
creates heat. If enough heat is generated, the rubber that holds the tire's cords
together begin to melt and the tire fails. See How Tires Work to learn more.
Because of the extra resistance an underinflated tire has when it rolls, your car's
engine has to work harder. AAA statistics show that tires that are underinflated by
as little as 2 psi reduce fuel efficiency by 10 percent. Over a year of driving, that
can amount to several hundred dollars in extra gas purchases.
Under inflated tires, waves are larger and the friction created is greater
If enough heat is generated, the rubber that holds the tire's cords
togetherbegin to melt
Friction creates heat and if enough heat is generated the rubber that holds the
tire cords melts and tire trails.
Self-inflating Systems:-
Inflate that tire back to the proper level - This means there has to be an air
supply as well as a check valve that opens only when needed.
Parts of A Self-inflating System
Get the air from the air source to the tires, which is usually through
the axle Systems either use a sealed-hub axle with a hose from the hub
to the tire valve or else they run tubes through the axle with the axle
acting as a conduit.
A pressure relief vent to vent air from the tire without risking damage
to the hub or rear-axle seals.
Driver can give direct control over the air pressure in each tire
CTIS: Inside:-
Parts are:
A wheel valve
Speed sensor
Pressure switch
Wheel valve:-
Part of the wheel valve's job is to isolate the tire from the system when it's
not in use in order to let the pressure off of the seal and extend its life.
The wheel valve also enables on-demand inflation and deflation of the tires.
Operator control panel:-
This dash-mounted panel displays current tire pressures, selected modes and
system status.
When the driver selects a tire-pressure setting, signals from the control panel
travel to the electronic control unit to the pneumatic control unit to the wheel
valves.
Pressure Switch:-
This type of system uses air from the same compressor that supplies air to
the brakes.
A pressure switch makes sure the brake system gets priority, preventing the
CTIS from taking air from the supply tank until the brake system is fully
charged.
one of the major systems in the developmental stages is the entire system.
This system uses a valve that pulls in air from the atmosphere.it then pumps
the air into the underinflated tire using a peristaltic pump action. The goal is
to maintain a specific pressure.
Model:-
This is the general layout of our model of the automatic inflation of tires. It
shows all the parts of the model and gives a general idea of its working.
Air Compressor
An air compressor is a device that converts power (usually from an electric motor,
a diesel engine or a gasoline engine) into kinetic energy by compressing and
pressurizing air, which, on command, can be released in quick bursts.
In fact, nowadays it is used for such purposes which you would not have imagined
in till the recent past. Basically, a modern air compressor amplifies the damaging
effect of water vapor and airborne particles by virtue of air compressors lowest
prices the compression process. Those days of spending hours pounding nails to
complete a project are over! sewing They are more susceptible to debris because
they do not have suction valves. Therefore, if space is not a significant issue, then
there is no need to focus specifically on the direction that the online shop target air
compressor s tank lays. Most of these have oil free target pumps which make them
very low maintenance. They can literally help you perform hundreds of functions
and can be taken just about anywhere. For garage purposes, an electric air
compressor will do fine. Plus make sure that any moisture has been removed from
the compressed air source before connecting prices the tool. Air Sander. Brands
names that would seem more comfortable in the use of a nail gun or jack hammer.
Installing and maintenance takes working knowledge of the application and the
vehicle where it is being installed. The compression that occurs in the air tanks of
your compressors compressor causes moisture to accumulate inside those tanks.
Poly Vinyl Chloride ( PVC) is another synthetic sewing laundry material composed
of thermoplastic lowest polymers which is used to make hose for air compressors
lowest prices special online applications. Everything seemed just fine. These
purchases often entail very few, if any, guarantees. Owning this kind of compressor
sounds fun and helpful but it shop is first important to consider the things before
buying it. This is the volume of the air that the gas compressor delivers. It is
recommended that you purchase an air compressor with a CFM capacity of 25%
greater than what you will need. All you have to do while going online is find the
latest models in the popular search engines and you would get access to a plethora
of information. The laundry second compressor takes this already compressed air
from the tank and air then recompresses it a second air compressors lowest prices
time and stores this air in a separate tank. Coleman air compressor is remarkable in
its use; it does not have a match because of the incredible duty and power it
possesses. Used air compressors have become a highly sought out commodity due
to this fact.
Pressure switch
A pressure switch is a form of switch that makes electrical contact when a certain
set pressure has been reached on its input. This is used to provide on/off switching
from a pneumatic or hydraulic source. The switch may be designed to make
contact either on pressure rise or on pressure fall.
Uses of pressure switches include:
Air seal is used to prevent the leakage of air from the pipes specially at joints and
bends. It can connect two pipes rigidly so that there is no leakage from them. It can
also makes pipes flexible so that they can be bent. These air seals are of many
materials but we use Teflon for our model.
Working of Our Model
The model mainly shows the automatic inflation of tires. In this model we use
components such as air compressor, non return valve, pressure switch, air seal
Pressure gauges, tire and pipes.
When the pressure of the tire decreases that reading is also shown on the
gauges of the pressure switch then the pressure switch starts the compressor
automatically start compressor and the tire gets inflated automatically to the point
which is preset. That presetting of the pressure value is the function of pressure
switch which can be adjusted to any value. When the compressor starts the
compressed air generated in it goes to the non return valve thento air seal through
the pressure switch which regulates it. This pressure switch is the important part of
our model fitted between non return valve and air seal it has two gauges which
shows the reading of pressure in tire. Then the air goes to the tire when it gets
inflated up to set point then the compressor automatically stops and the air supply
also stops.
We also use some safety concerns for proper and safe working of our project
such as an aluminium pipe is fitted between compressor and pressure switch. If
there is any blockage in the system so that the air cant go further in that case our
compressor can burst which leads to a serious accident. In that case the aluminium
pipe will burst and releases the air and there is no harm to our compressor. The
two gauges are used in the system because in case if any of the gauge stops
working so we get reading from the other gauge.
Cost report
Air Compressor : - Rs. 9500
Friction creates heat and if enough heat is generated the rubber that holds the tire
cords melts and tire trails.
Because of the extra resistance an under inflated tire has when it rolls,thecars
engine has to work harder.
ATI systems can not only extend tire life but truck fleets can also see additional
savings from reducing the risk ofexpensive tire failure caused by underinflation.
2. www.howstuffswork.com
3. www.cycloid.com
4. www.goodyeartyres.com
5. Wikipedia