Escolar Documentos
Profissional Documentos
Cultura Documentos
ELECTRO-MAGNETIC COMPATIBILITY
The DSE7310 is an Auto Start The DSE7320 will also monitor the The extensive list of features TEMPERATURE
Control Module and the DSE7320 is mains (utility) supply. The modules includes enhanced event and BS EN 60068-2-1
Ab/Ae Cold Test -30 oC
an Auto Mains (Utility) Failure include USB, RS232 and RS485 performance monitoring, remote BS EN 60068-2-2
Control Module suitable for a wide ports as well as dedicated communications, PLC functionality Bb/Be Dry Heat +70 oC
variety of single, diesel or gas, DSENet terminals for system and dual mutual standby (DSE7310 VIBRATION
gen-set applications. expansion. only) to reduce engine wear. BS EN 60068-2-6
Ten sweeps in each of three
major axes
Monitoring an extensive number of Both modules are compatible with The modules can be easily 5 Hz to 8 Hz @ +/-7.5 mm,
engine parameters, the modules will electronic (CAN) and non-electronic configured using the DSE 8 Hz to 500 Hz @ 2 gn
display warnings, shutdown and (magnetic pick-up/alternator Configuration Suite PC software. HUMIDITY
engine status information on the sensing) engines and offer an Selected front panel editing is also BS EN 60068-2-30
back-lit LCD screen, illuminated extensive number of flexible inputs, available. Db Damp Heat Cyclic 20/55 oC
@ 95% RH 48 Hours
LEDs, remote PC and via SMS text outputs and extensive engine BS EN 60068-2-78
alerts (with external modem). protections so the system can be Cab Damp Heat Static 40 oC
easily adapted to meet the most @ 93% RH 48 Hours
DEGREES OF PROTECTION
PROVIDED BY ENCLOSURES
BS EN 60529
IP65 - Front of module when installed into the
control panel with the supplied sealing gasket.
DEUTZ
DSE7310/20 ISUZU
PERKINS
CATERPILLAR
MTU
7 VOLVO
CUMMINS
OTHER SCANIA
MAINS (UTILITY) N/C VOLT FREE N/O VOLT GENERATOR SENSING CHARGE FUEL & CRANK ELECTRONIC
SENSING OUTPUT FREE OUTPUT ALTERNATOR OUTPUTS ENGINES &
DSE7320 ONLY (Flexible with CAN) MAGNETIC PICK-UP
ISSUE 6
DSEGenset
SPECIFICATION
DSE7310/20 DC SUPPLY
CONTINUOUS VOLTAGE RATING
8 V to 35 V Continuous
AUTO START & AUTO MAINS FAILURE CRANKING DROPOUTS
CONTROL MODULES Able to survive 0 V for 50 mS, providing
supply was at least 10 V before dropout and
supply recovers to 5 V. This is achieved
without the need for internal batteries.
FEATURES LEDs and backlight will not be maintained
DSE7320 during cranking.
FREQUENCY RANGE
3.5 Hz to 75 Hz
OUTPUTS
OUTPUT A (FUEL)
15 A DC at supply voltage
KEY FEATURES LED and LCD alarm indication KEY BENEFITS
4-Line back-lit LCD text display Power monitoring (kW h, kV Ar, 132 x 64 pixel ratio display for OUTPUT B (START)
15 A DC at supply voltage
Five key menu navigation kV A h, kV Ar h) clarity
Front panel editing with PIN Load switching (load shedding Real-time clock provides OUTPUTS C & D
protection and dummy load outputs) accurate event logging 8 A 250 V (Volt free)
Customisable status screens Automatic load transfer (DSE7320) Multiple date and time scheduler AUXILIARY OUTPUTS E,F,G,H
Power save mode Unbalanced load protection Set maintenance periods can 2 A DC at supply voltage
Support for up to three remote Independent Earth Fault trip be configured to maintain
GENERATOR
display units True dual mutual standby with load optimum engine performance VOLTAGE RANGE
9 configurable inputs balancing timer (DSE7310 only) Ethernet communications (via 15 V to 415 V AC (Ph to N)
8 configurable outputs USB connectivity DSE855 module), provides 26 V to 719 V AC (Ph to Ph)
Flexible sender inputs Backed up real time clock advanced remote monitoring FREQUENCY RANGE
Configurable timers and alarms Fully configurable via DSE Modules can be integrated into 3.5 Hz to 75 Hz
3 configurable maintenance Configuration Suite PC software building management systems
MAGNETIC PICK UP
alarms Configurable display languages (BMS) VOLTAGE RANGE
Multiple date and time scheduler Remote SCADA monitoring via Increased input and output +/- 0.5 V to 70 V
Configurable event log (250) DSE Configuration Suite PC expansion capability via DSENet
FREQUENCY RANGE
Tier 4 CAN engine support software Licence-free PC software 10,000 Hz (max)
Integral PLC editor User selectable RS232 and IP65 rating (with supplied
Easy access diagnostic page RS485 communications gasket) offers increased DIMENSIONS
OVERALL
CAN and Magnetic Pick-up/Alt. Configurable Gencomm pages resistance to water ingress 240 mm x 181 mm x 42 mm
sensing Advanced SMS messaging PLC editor allows user 9.4 x 7.1 x 1.6
Fuel usage monitor and low fuel (additional external modem configurable functions to meet
PANEL CUT-OUT
alarms required) specific application 220 mm x 160 mm
Charge alternator failure alarm Start & stop capability via SMS requirements 8.7 x 6.3
Manual speed control (on messaging
MAXIMUM PANEL THICKNESS
compatible CAN engines) Additional display screens to 8 mm
Manual fuel pump control help with modem diagnostics 0.3
Engine exerciser Idle control for starting &
OPERATING TEMPERATURE RANGE
Protections disabled feature stopping. -30C to +70C
kW & kV Ar protection DSENet expansion compatible
Reverse power (kW & kV Ar) Heated display option available STORAGE TEMPERATURE RANGE
-40C to +80C
protection
RELATED MATERIALS
TITLE PART NOS
DSE7310 Installation Instructions 053-028
DSE7320 Installation Instructions 053-029
DSE7200/7300 Quick Start Guide 057-101
DSE7200/7300 Operator Manual 057-074
DSE7200/7300 Configuration Suite PC Manual 057-077
Deep Sea Electronics Plc maintains a policy of continuous development and reserves the right to change Registered in England & Wales No.01319649 055-051/10/11 (14)
the details shown on this data sheet without prior notice. The contents are intended for guidance only. VAT No.316923457