Escolar Documentos
Profissional Documentos
Cultura Documentos
PROBLEMA 3.- A Steel rod of 15 mm diameter is held snugly (but without any initial
stresses) between rigid walls by the arrangement shown in the figure. (Fort he Steel rod
use a = 1210-6 /C and E = 200 GPa).
a) Calculate the temperature drop DT (degrees Celcius) at witch the average shear stress
in the 12 mm diameter bolt becomes 45 MPa.
b) What are the average bearing stresses in the bolt and elevis at A and the washer (dw =
20 mm) and wall (t = 18 mm) at B?
EL PROFESOR
SOLUCIN
La barra soporta la
fuerza P de compresin
a) x en funcin de P
x P
x x
E EA
Por Hooke;
Reemplazando valores:
1
x ( P) x 2.54647 10 9
200000 (0.7854 (50 50))
d Sy A
(m E (MPa (mm
m) (Mpa) ) 2) 1/EA Rpta (a) Rpta (b) y
2000 1963 -2.54647 x x = -2.54647 x y = 7.63942 x 0.00
-9
50 0 00 400 .5 10-6 10 P 10-10 P 05
Rpta (c)
Pmax (d) max (e) max (f)
(Newton) (Mpa) (Mpa) F.S
654500 333.33 166.67 1.2
PROBLEMA 2.- Una barra de acero AD (E = 210 GPa) tiene una seccin transversal de 260 mm 2 y
soporta las cargas P1 = 12 KN, P2 = 8 KN y P3 = 6 KN. Las longitudes de los segmentos de la barra
son: a = 1.5 m, b = 0.6 m y c = 0.9 m. Se pide
a) D.C.L. de la barra y clculo de reaccin en el apoyo.
b) Clculo de esfuerzos en cada tramo de la barra.
c) Clculo de las deformaciones respectivas
d) Desplazamiento del extremo libre de la barra
e) Que incremento de la carga P3 se requiere para que la
barra no sufra cambio de longitud cuando son
aplicadas las tres cargas? (2 puntos)
A L
BARR (mm (mm x k
A 2) E ) F (N) (MPa) (N/mm) 1/K) (mm)
21000 1400 53.84 2.74725E
AB 260 0 1500 0 62 36400 -05 0.3846
21000 7.692 1.0989E-
BC 260 0 600 2000 31 91000 05 0.022
-
21000 - 23.07 60666. 1.64835E
CD 260 0 900 6000 7 67 -05 -0.099
5.49451E 0.30
-05 77
total=0.3077
P3 (Newtons)
5600
PROBLEMA 3.- A Steel rod of 15 mm diameter is held snugly (but without any initial
stresses) between rigid walls by the arrangement shown in the figure. (Fort he Steel rod
use a = 1210-6 /C and E = 200 GPa).
c) Calculate the temperature drop DT (degrees Celcius) at witch the average shear stress
in the 12 mm diameter bolt becomes 45 MPa.
d) What are the average bearing stresses in the bolt and elevis at A and the washer (dw =
20 mm) and wall (t = 18 mm) at B?
SOLUCIN
La caida de temperatura DT origina contraccin en la barra AB y genera esfuerzos de
traccin en la barra AB y esfuerzos de aplastamiento entre el perno y la horquilla y en la
arandela contra la pared de espesor 18 mm.
Aapla
De d st
(mm (mm t A (mm2 ad
(/C) ) ) (mm) (mm2) ) E (Mpa) m 1/(E)
BARRA 1.20E- 176.71 4.17E-
AB 05 - - - 15 5 200000 01
113.09
PERNO --- 12 8 120 200000 45
ARANDEL 137.4
A 20 15 45 200000
HORQUIL
LA 10 120
T aplast
F (N) (C) (Mpa)
10178.7
8 24.00
42.41
74.06
42.41