Você está na página 1de 3

Model NO .

3GPX0505F9

XXX Pol Panel Triple Beam Antenna


3824-960MHz 22 19dBi 9 FET
ELECTRICAL SPECIFICATIONS

824-960
Frequency Range (MHz):
824-862 862-894 894-960
Gain (dBi): 18.5 19 19.2
Return Loss (dB): >15 (VSWR<1.43)
Polarization (): 45
Horizontal 3dB Beamwidth (): 324 322 320
Horizontal 10dB Beamwidth (): 346 344 342
Horizontal Beam Pointing (): -41, 0, +41 -38, 0, +38 -35, 0, +35
Vertical 3dB Beamwidth (): 14.5 14.0 13.0
Electrical Downtilt (): 9 Fixed
Upper Sidelobe Level (dB): 18 17 16
Front to Back Ratio (dB): >28 >26 >25
Isolation Between Polarizations (dB): >25
Isolation Between Beams (dB) >16
Power Rating (W): 300
Intermodulation IM3 (dBm): <-107 (243 dBm)
Impedance (ohm): 50
Lightning Protection: DC Grounded
Connector Type: 67/16 DIN Female
MECHANICAL DATA

Antenna Dimensions (mm): 1299833104


Packing Dimensions (mm): 1458991242
Antenna Net Weight (kg): 28
Antenna Gross Weight (kg): 38.2
Radome Material: Fiberglass
Pipe OD (mm): 70-114
Mounting Kits (Included): Adjustable Downtilt 0-12
ENVIRONMENTAL RATINGS

Humidity: 95%RH@+30
Temperature (): -40+70
Wind Load @150 km/h (N): Frontal/Lateral/Rearside: 1058/165/1323

W:www.broadradio.cn E:info@broadradio.cn V 7.0 2015/7/9


BROADRADIO is continually improving products. Specifications may change at any time without notice
1/2
Azimuth Elevation

Product Size Detail

End Cap Layout

W:www.broadradio.cn E:info@broadradio.cn V 7.0 2015/7/9


BROADRADIO is continually improving products. Specifications may change at any time without notice
2/2
Model AF-T003-GL, Installation Instruction for 12 Degrees Mounting Bracket

12 M16 Stud 2
11 14 Plain Washers 2 The fixing holes without the
studs,nuts and washers.
10 M16 Washer GAL 6
8 9 10 1
9 M16 Spring Washer GAL 4 2 11
8 .5-N Nut GAL 6 4 5 6 7
1 Torque 95Nm Torque 38Nm
7 M12-N Nut GAL 4 9 10
6 M12 Spring Washer GAL 4 12
5 M12 Washer GAL 8 8 9 10
3
4 M12*35-N Bolt GAL 4 74 5 6
3 12 Angle Adjusting Plate 1 Upper bracket exploded view
Torque 38Nm
2 Fixed Plate 1
1 Bracket Clip 2
8 9 10
No. Upper Bracket Assembly QTY 9 10
Warning: To
7 2 Torque 38Nm
avoid antenna
falling, the
10 M16 Washer GAL 6 reserved holes
9 .5-N Nut GAL 6 are suggested Tilt angle adjusting holes
1 to hang the
8 M16 Spring Washer GAL 4 antenna using
7 M16 Stud 2 chains.
3 4 5 6 8 9 10
6 M12-N Nut GAL 2 Lower bracket exploded view
Torque 95Nm
5 M12 Spring Washer GAL 2
Torque 38Nm
4 M12 Washer GAL 4
3 M12*35-N Stud GAL 2
2 Fixed Plate 1
1 Bracket Clip 2
Upper bracket Lower bracket
No. Lower Bracket Assembly QTY assembly assembly

Step 4: Adjust the array of holes


through the board, the mechanical
Step 3: Use M16 bolts tilt angle of the antenna is adjusted
Step 2: Use M12 bolts to fasten and nuts to fasten the to a specified value. Lock all the Step 5: When the mechanical
Step 1: Please check all the components in the the bracket onto the antenna antenna on the mast with fasteners with torque wrench, The tilt angle is 0 degree, the angle
list are provided and have not been damaged back, tighten up the pointing bolts torque 38Nm.The mast first hole denotes mechanical tilt adjusting plate is suggested to
(the brackets have installed). The installed and nuts with reference torque diameter should be in the angle with 0 degree, 2 degrees be fixed by two holes which
sketch maps are shown above. shown in the diagram above. range of 70 to 114mm. increasement with one hole. shown in the picture above.

Warning: Please mount the bracket according to the installation instruction. The installation party should take corresponding
responsibility for the situation that the bracket or antenna was broken without follow ing the installation instruction.

Você também pode gostar