Escolar Documentos
Profissional Documentos
Cultura Documentos
To regulator valve To control switch valve, 4 To shift control vaive To pressure control valve-A,B. High & low pressure valve = ‘Manual valve i i aq ma bok Livi PRWDEL From i pimp PRESSURE CONTROL VALVE-A, B Pressure control valve A, B regulate the pressure supplied to each clutch under the control of the pressure control so- lenoid valve A, 8 to eliminate shock at the time of shifting, 41. Pressure control valve A - Not operated To 1-2 shitvave From manual valve vale ee Controls by POSY.-A viva slenod valve ON { From reducing valve PRESSURE CONTROL VALVE-A, B 1. Pressure control valve A - Operation Torgenttvane { booAT -28 AUTOMATIC TRANSAXLE (A4AF3) PRESSURE CONTROL VALVE-A, B 1. Pressure control valve B - Not Operated To (Rear euch exhaust valve) 1 From (manual vaive) | 4 U ee CContaes by (PCSV-8 vave) From (reducing vane) PRESSURE CONTROL VALVE-A, B 1. Pressure control valve B - Operation ‘The main function of this valve controls the rear clutch independently jo Pressure solenod valve OFF SHIFT CONTROL VALVE(SCV) AND SOLENOID VALVE-A, B, C (SCSV-A,B,C) The line pressure acting upon the shift control valve is controlled by the two shift control solenoid valves(which are switch ON and OFF according to the shifting gear by the transaxle control module command), and the shift con- trol valve is activated according to the shifting gear, thus switching the oil passages. The relationship of the shifting gear and the ON-OFF switch of shift control solenoid valve "A, "B* and "C" is shown in the table below. ‘Operation Shift control solenoid vaive Position A B € istgear_|__ON ‘ON OFF ‘2nd gear | _ OFF ‘ON OFF 3rd.gear_ | OFF (OFF ON. 4th gear | ON OFF ON. CONTROL SWITCH VALVE(CSV) & END CLUTCH(E/C) VALVE - Function ‘Switching the pressure of E/C and SA ~ T Hs Fer]AUTOMATIC TRANSAXLE SYSTEM CONTROL SWITCH VALVE(CSV) & E/C VALVE - 2nd Gear + 2nd pressure is supplied from SA through the CSV + SCSV-C maintains OFF as well as 2nd gear. ToeIC boner a! csv ] au From 12 shitvaie BORE 1c vale OFF. CONTROL SWITCH VALVE(CSV) & E/C VALVE = 2nd 3rd gear + SCSV-C maintains OFF as well as 2nd gear. + The E/C pressure from shift control valve is inter- cepted at the E/C valve during up-shifting from 2nd to 3rd gear. + SA pressure is supplied from 1-2 shift valve, but the front clutch and SR pressure is also supplied from the 2-3/4-3 shift valve, so the both SR and SA pressure will be set off ToEie Tosa csv Sse] fell tc va AT CONTROL SWITCH VALVE(CSV) & E/C VALVE + 3rd gear + SCSV-C is changed from OFF to ON. + The EIC pressure is supplied from 1-2 shift valve at the CSV after finishing the up-shifting from 2nd to 3rd gear. + SA pressure is supplied from shift control valve, but the front clutch and SR pressure is also supplied from the 2-3/4-3shift valve, so the both SR and SA pressure will be set off eee = rosa jt som rt cwt+ 2 L- rom sev a wove ox BY rom SovAT -30 AUTOMATIC TRANSAXLE (A4AF3) 4+ 2 SKIP SHIFT c. Continuous switching to SA From (SCY) to SA through (CSV) FAIL SAFE FUNCTION 1. Operating elements Speed RIC. EC. «iD 4. TOM malfunction in 1st or 2nd gear. 4th : o 9 CUTTING OFF THE E/C PRESSURE BY E/C VALVE 2nd ° = ° Speed | FIC RIC EIC KID 2. Controls ist ° a. RIC engaging duty control mn b.EIC releasing duty control 2nd ° ° ©. Continuous switching to SA Fail ° ° 3. Description = FIC, SR: from 2-3/4-3 shift valve ‘a. RIC engaging duty control + RIC: from PCV-B + SA: from 1-2 shift valve ToRIG 1} From mancal Viv Tokic ony ] ews 2 {| & te conte f OSV duty contra b. EIC releasing duty control ween 4 +2 Skip shift only (SCSV-C ON) ‘When releasing the E/C clutch pressure, itis con- trolled by duty of PCSV-A only in case of 4» 2 skip shit. conto ten From e:¢ To SA \ tAUTOMATIC TRANSAXLE SYSTEM 2. TCM malfunction in 1st or 2nd gear. If the hydraulic pressure is supplied to E/C and the FIC, SR pressure is delayed Speed | FIC | RIC | EC | KID 1st ° 2nd ° ° Fail ° ° + RIC, E/C, SIA : interlock oe = Tosa 1 re csv Poa oe Beare] cow f From SCV NOTE SA: Servo Apply pressure F/G : Front Clutch pressure RIC : Rear Clutch pressure KID : Kick Down SCV: Shift Control Valve CSV: Control Switch Valve POSV : Pressure Control Solenoid Valve ‘SCSV: Shift Control Solenoid Valve POV : Pressure Control Valve ROEV : Rear Clutch Exhaust Valve AT -31AT 32 AUTOMATIC TRANSAXLE (A4AF3) AUTOMATIC TRANSAXLE HYDRAULIC CIRCUIT PARKING AND NEUTRAL YA," PRESSUREAUTOMATIC TRANSAXLE SYSTEM AT -33 D RANGE(1ST) YA se Pressure TORQUE CONVERTER AND LUBRICATION PRESSURE REDUCING PRESSUREAT 34 AUTOMATIC TRANSAXLE (A4AF3) D RANGE(2ND) V/sAUTOMATIC TRANSAXLE SYSTEM AT 35 D RANGE(3RD)AT 36 AUTOMATIC TRANSAXLE (A4AF3) D RANGE(4TH) 77 \NE PRESSURE TORQUE CONVERTER AND LUBRICATION PRESSURE EZZZZZY *=0ucNG PRESSUREAUTOMATIC TRANSAXLE SYSTEM Lock AT 37 UNE PRESSURE REDUCING PRESSUREAT -38 AUTOMATIC TRANSAXLE (A4AF3) REVERSE UNE PRESSURE TORQUE CONVERTER AND LUBRICATION PRESSURE REDUCING PRESSUREAUTOMATIC TRANSAXLE SYSTEM ELECTRONIC CONTROL SYSTEM Inhibitor switch — Pressure control |»} " ‘solenoia valve -A Input shaft speed sensor [/——> Output shaft speed sensor -——> Prossure contol |_| solenoia vale B Shit control Fluid tamporature sensor |» |} *Soienoia T se Kickdown servo switch |___p»- Shit contro 1D off switch |} [—*| _sateneis vale B CAN M —— Shift contro 1.TPS signal > [>] “solenoia 2! Engina RPM signal valve C 4. Torque reduction pressure operation /alowance! | | —> alsalonance signal 4.Torque reduction request. [*— signa Damper clutch 5.\ehicle speed sensor [>] contro! sotenois valve HI-SCAN — |—»] oottiameAT ~40 AUTOMATIC TRANSAXLE (A4AF3) SENSOR AND ACTUATOR FUNCTION Functions Input shaft speed sensor Detect the turbine RPM at the E/C retainer Output shaft speed sensor Detect the T/F drive gear RPM at the transfer drive gear Engine RPM signal Receive the engine RPM via communication with ECU Vehicle speed sensor Detect the vehicle speed at the speedometer gear Kickdown servo switch Detect the operation starting of kickdawn brake Inhibitor switch Detect the position of select lever through the contact switch Overdrive switch Detect the position of overdrive(4th gear) TPS Detect the throttle open angle through the potentiometer Fluid temperature sensor Detect the temperature of ATF through the thermistor Torque reduction request signal ‘Transmit the torque reduction request signal to the engine ECU Torque reduction operation/allowanceldis- allowance signal Receive the signal of engine reduction pressure operation J allowanceldisallowance from the ECU Pressure control solenoid vaive-A Control the hydraulic pressure to the pressure control valve for shift control Prossure control solenoid valve-8 Control the hydraulic pressure to the pressure control valve for shift control Shifting control solenoid valve-A Make the hydraulic passage for shift control Shifting control solenoid valve-B Make the hydraulic passage for shift control Shifting control solenoid valve-C Make the hydraulic passage for shift control Damper clutch control solenoid valve Control the hydraulic pressure for the damper clutch control * E/C : End Clutch TF : TransferAUTOMATIC TRANSAXLE SYSTEM AT 41 INTEGRATED TCM SIDE CONNECTOR INTEGRATED TCM INPUT/OUTPUT TERMINAL VOLTAGE Inputloutput value PIN Signal Condition puro Test result | Remark Ne. Type Level @ | ater vtage De 5 (Main relay) IS ON Voltage VBR VBR vBaT Tory a [Srteintatsoenae | sung | 28 way ory valve fohage Vpeak : Max. -2V 0.69 V VAT Tory 27 | Sti control solenoid | shiging | OC Max. 1.0V 96 mV valve: foltage Vpeak : Max. -2V 0.69 V wae] Pulse | HI: V_BAT or veo 728V Dave postion 10 Max, 1.0V anv 48 | Pum signal to tp Freq, :S0H242% (Reference) | 50.0 He computer | 2: Postion | Duy 72.582" 725% Pastion 12.582" 128% v_BaT Ta97v so | sniteonvet scent] sung | OC van tov Pony valve: foltag Vpeak : Max. -2V 0.78 Fluid temperature 176 or vaing | Anat os4sv aaev sensor 0 a (161.6°F) soo Gonoratn Sine | Vplp: Above 10 Taav 60 | Pulse Generator 8 BOkph Wave | Freq.: 1.5~2.0kHz (Reference) | 1.98 kHz sine | __Vp_p: Above 1.0V 286 V 61 | Pulse Generator A | 3,0001PM | Waye | Freq. 1.1~1.3kHz (Reference) | 1.25 kHz Release Wax. 0.5 00 mv 63 Brake SW Push V_BAT 12.24 V 7 range V.BAT 115V 66 Inhibitor SW Otherwise Max, 1.0V. 3.4 mV range v.BAT 1421 er Inhibitor SW "P Otherwise Max, 1,0V. 42mV "Lange v.BAT 1415V hi Inhibitor SW "L" Otherwise Max, 1.0V. 3.7 mV 7o_[_Pwe GND ing Wax. SOnV 42m HI: V_BAT 13.8V eee ressure cont Z ake rr] Pressure contol | soiting | Pulse LO Max. -30V basy |e solenoid valve- \Vpeak : Max. -60V 13.5VAT ~42 AUTOMATIC TRANSAXLE (A4AF3) Inputioutput valve IN| signat | contion tlt Testresutt | Remark : Type Level Pressure control HI: V_BAT 13.8. | (50.0Hz/ 72 | Pressure contol | shiting | Pulse | LO: Max. -30V oasy |asete peak Max -sov | -135V_| Chopping) 25V ao | Fd temeeratue | iaing | Analog ov - 49v eo (136°F)) Sie | Vp_p? Above 100 1a2V 82 | Pulse Generator B 60kph Wave | Freq.: 1.5~2.0kHz (Reference) | 1.98 kHz Sine | __Vp_p: Abow 1.0V 385V 83 | Pulse Generator A | 3,000rPM | Wave | Freq.: 1.1~1.3kHz (Reference) | 1.25 kHz 1,3 speed Wax. 1.0V 00 mv a | kickdownkib) seve | 1:9 speed ax oo my bor SW >Re range V.BAT 179 88 | Inhibitor SW'R’ | otherwise Max. 4.0V 3.4 mv range | 0c V_BAT 1410 89 | Inhibitor Sw "2 Otherwise | Voltage Max. 1.0V 44mv 0D OFF BAT 14ziv 80 OD OFF SW OD ON Max. 1.0V. 0.0 mv ne) ON range v_BAT 14z2V a Inhibitor SW °N Otherwise Max. 1.0V. 3.6 mV AI: V_BAT vaav_ |@sonet oa | Damper iter | coccupon | Puse | Lomax. ov barv [aaa peek" Wax. cov | 135 _[Chopring) - V_BAT: Battery Voltage VBR : Converted battery voltage via main relayAUTOMATIC TRANSAXLE SYSTEM TROUBLESHOOTING | esstices AT -43 [Gatner information trom customer i Verify complaint 1 Communication with Record the DT fail-safe code (Cand | _scantoolimpossible inspection procedure No.1 in inspection chart for trouble symptom Erase the OTC ‘Abnormal code output Normal code displayed [Basic inspection tem adjustment J Abnormality exists (No DTC) Road leet No. abnornity Rechec! before t DTCs which were read ne road test Ab output rormal code Normal code displayed To inspection chart for ore) To Inspection char for rouble system + ¥ ‘Search for cause ' [Found | Not ouna Repair j NS] NG Iptermittent malfunctions CContirmation test | OK (Road test) [OK completed 0K +AT ~44 AUTOMATIC TRANSAXLE (A4AF3) DIAGNOSITC TORUBLE CODES (INSPECTION 6. Delete the diagnostic trouble code. PROCEDURE) CHECK THE DIAGNOSTIC TROUBLE CODES 7. Disconnect the Hi-scan tool. NOTE 1. Turn the ignition switch to OFF. DTC cleaning should only be done with the scan tool 2. Connect the Hi-scan tool to the DLC connector for diagnosis. 3. Turn the ignition switch to ON. 4. Check the diagnostic trouble codes using the Hi-scan tool 5. Read the output diagnostic trouble codes. Then follow the remedy procedures according to the "DIAGNOS- TIC TROUBLE CODE DESCRIPTION’ on the follow- ing pages. NOTE + A maximum of 10 diagnostic trouble codes {in the sequence of occurrence) can be stored in the Random Access Memory (RAM) incorporated within the contro! module. + The same diagnostic trouble code can be stored cone timo only. + Ifthe number of stored diagnostic trouble codes or diagnostic trouble pattems exceeds 10, al- ready stored diagnostic trouble codes will be erased in sequence, beginning with the oldest. + Do not disconnect the battery unti all diagnos- tic trouble codes or diagnostic trouble patterns have been read out, because all stored diag- nostic trouble codes or diagnostic trouble pat- tems wil be cancelled when the battery is dis- connected. + All diagnostic trouble codes are deleted from ‘memory the 200th time the ATF temperature reaches 50°O(122'F) after memorization of the most recent diagnostic code,AUTOMATIC TRANSAXLE SYSTEM AT -45 DIAGNOSTIC TROUBLE CODE TABLE No. | Code Tem MIL_| Remark 1 | Po7o7 | TRANSAXLE RANGE SWITCH CIRCUIT LOW INPUT @ | ars3 2 | Po70e | TRANSAXLE RANGE SWITCH CIRCUIT HIGH INPUT e@ | Arse 3. | Po7t1 | TRANSAXLE FLUID TEMPERATURE SENSOR RATIONALITY @ | are 4 | Por12 | TRANSAXLE FLUID TEMPERATURE SENSOR CIRCUIT LOW INPUT @ | ares 5. | Po713 | TRANSAXLE FLUID TEMPERATURE SENSOR CIRCUIT HIGH INPUT e | arm 6 | P0716 | AIT INPUT SPEED SENSOR(PG-A)-TOO MAX AL-T3 7_| Po7t7 | AT INPUT SPEED SENSOR(PG-A) CIRCUIT - OPEN or SHORT(GND) e@ | Are0 8 | P0722 | A/T OUTPUT SPEED SENSOR(PG-8) CIRCUIT - OPEN or SHORT(GND) e@ | atez 9 | P0731 | GEAR 1 INCORRECT RATIO e@ | Arse 10 | P0732 | GEAR 2 INCORRECT RATIO @ | arse 11 | P0733 | GEAR 3 INCORRECT RATIO @ | Ar-t03 12 | Pora4 | GEAR 4 INCORRECT RATIO @ | arto 13 | Pova1 | TORQUE CONVERTER CLUTCH STUCK OFF @ | aris 14 | P0742 | TORQUE CONVERTER CLUTCH STUCK ON AT-120 15 | Po74s | TCC CONTROL SOLENOID VALVE CIRCUIT - OPEN or SHORT(GND) @ | aris 16 | P0745 | PRESSURE CONTROL SOLENOID VALVE-A CIRCUIT - OPEN or SHORT(GND) AT-128 17 | P0760 | SHIFT CONTROL SOLENOID VALVE-A CIRCUIT - OPEN or SHORT(GND) @ | Aris 18 | P0765 | SHIFT CONTROL SOLENOID VALVE-B CIRCUIT - OPEN or SHORT(GND) @ | arss7 19 | P0760 | SHIFT CONTROL SOLENOID VALVE-C CIRCUIT - OPEN or SHORT(GND) @ | ars 20 | P0775 | PRESSURE CONTROL SOLENOID VALVE-8 CIRCUIT - OPEN or SHORT(GND) | @ | AT-145 21 | P1709 | KICKDOWN SERVO SWITCH CIRCUIT - OPEN or SHORT @ | Ato 22 | vooot [CAN BUS OFF @ | Arss7 23 | uoro0 | CAN TIME OUT @ | at-t60 NOTE D/C : Damper clutch PGA Input shaft rotation speed sensor PG-B : Output shaft rotation speed sensor PCSV: Pressure control solenoid valve SCSV: Shift solenoid valveAT ~46 AUTOMATIC TRANSAXLE (A4AF3) CHECK THE CONTROL SYSTEM (USING THE HESCAN TOOL) Checking procedures Diagnosis tems Probable cause Check conditions Normal value Fluid temperature | Engine doesnt operate Equivalent to outside |~ Malfunction ofthe Nuid sensor before starting ar temperature temperature sensor or the While warming up engine ‘Gradual increase circuit hamess 20-110 Alter warming up engine to Kickdown serve ange ding ON = Malfunction of the Kekdown switch soo dota SAGO serv adusiment We Ast or 3rd g ON + Malfunction of the kickdown servo awich oF the circu. harness Dirange :2nd or 4th gear OFF + Malfunction of the kickdown servo system Tarlton signal "Niange: ding 350-900;pm__|~ _Malfunction of the ignition Engine rpm system ange, 2500rpm 72400-2600rem Tecan ee + Maifunetion of the ignition (Tachometer) signal pick-up crcut Tding switch Accelerator pedal fully released ON = Malfunction of the TPS adjustment OFF Press accelerator pedal slightly + Malfunction of the TPS or the circuit harness ‘ir condtoning Air conditioning ON ON = Malfunction ofthe al relay signal Airconditioning OFF OFF ondioning power relay Transaxle range Idling C(creep) - Malfunction of the TCM switch = Malfunction of the idling taling ‘st gear ‘switch system 2nd gear 2nd gear__|- Malfunction of the inhibitor Overdrive switch is eatich system turned OFF, 3rd gear 3rd gear + Malfunction of the TPS system "Drange: Overdive switch is turned ON, 4th gear 4th gear Pulse generator A | "D'range: Engine stopped rpm Malfunction ofthe pulse * Turbine rm angeDawng a a0 2a0 generator othe cre S0kmn/n(3tmgh) in 3rd gear + Incoming noise trom outside "Drrange:Driving at 7100-1400rpm Sokmin(Simph) in Ath goar Pulse generatorB | "D'range: Engine stopped rpm Malfunction ofthe pulse * Output shat ange:Driving at 7600-2000rem generator 8 or the crcut SOkrn/h(3imph) in 3rd gear = Incoming noise from outside "Drrange:Driving at 7600-2000rpm Sokmin(Simph) in Ath goar Overdrive switch | Overdrive switch is tumed ON OD:ON |= Malfunation ofthe overdrive (Overdrive switch is turned OFF ‘OD:OFF ‘switch or the circuit harnessAUTOMATIC TRANSAXLE SYSTEM AT -47 Diagnosis items Checking procedures Check conditions Probable cause duty(PCSV duty) Age: During shift Varies with condition Inhibitor switch | Shift select lever to "Prange P Malfunction ofthe inhibitor Shift select lever to "R’range R switch adjustment Malfunction ofthe inhibitor Shift select lover to “Nerange N suitch or the circuit hamess Shift select lever to “Drange D Malfunction of the manual Shift select lever to "range 2 Shift select lover to *Urange L Vehicle speed sensor | Keep vehicle stopped Oke Malfunction ofthe vehicle sa speed sensor if high speed Driving at 30km/h(19mph) 30kmv/h(19mph) signal is delivered while Driving at SOknv/h(31mph) Sokmih(3imph) vehicle is stopping In other cases, matfunction af the vehicle speed sensor or circuit names Pressure control | Drange = Idling 30-80% When accelerator podal is solenoid valve Drange Tet goa “00% slightly pressed wii idling in "D'range, duty should becomet00% Malfunction of the TCM Malfunction of the TPS system Malfunction of the idling switch system (Tachometer) "D'range: Srd gear, 2500rpm (Tachometer) Varies with load Damper clutch slip | *D'range: 3rd gear, 1500rpm '200~300rpm ‘Malfunction of the damper rpm (Tachometer) clutch + Turbine rem [srange: ard gear S50; opm Malfneton of he ignton (Tochoreter) signal wire or pulse generator-B system ‘Abnormality transaxle fluid pressure Malfunction of the damper clutch solenoid valve DCCSV duty *D'range: Srd gear, 1500rpm 0% Malfunction of the TCM Malfunction of the TPS system Malfunction of the pulse generator-B systemAT ~48 AUTOMATIC TRANSAXLE (A4AF3) FLUID LEAKS INSPECTION Check for leaks from the transmission. If there are leaks, itis necessary to repair or replace O-ring, seal packings, «il seals, plugs or other parts Rear cover assembly ‘and rear cover °O — \ Diferental Drain plug Ci pan assembly and gasket TRANSAXLE FLUID LEVEL INSPECTION 1. Park the vehicle at even straight surface. 2. Before removing the oil level gauge, wipe all contam- inants from around the oil level gauge. 3. Set the select lever to the “P"position and engage the pparking brake and then start the engine. 4, Drive the vehicle until the fluid reaches nor mal.{80-90°C(176~194"F)) 5. Move the select lever through all positions. This will fill the torque converter with transaxle fluid. Set the select lever to the "N"(Neutral) position. 6. Check that the fluid level is the *HOT'mark on the ‘ill level gauge. If uid level is low, add automatic transaxle fluidunti the level reaches the "HOT" mark, ‘Automatic transaxle fluid GENUINE DIAMOND ATF SP-lIl or SK ATF SP-tIl Quantity: 6.1/ (6.4 US at, 5.4 Imp.qt) NOTE Low fluid level can cause a variety of abnormal con- ditions because it allows thepump to take in air along with fluid. Air trapped in the hydraulic system forms bubbles, which are compressible, Therefore, pressures will be erratic, causing delayed shifting, slipping clutches and brakes, etc. Improper filing can also raise fluid level too high. When the transaxle has too much fluid, gears churn up foam ‘and cause the same conditions which accur with low fluid level, resutting in accelerated deterioration of au- tomatic transaxle Mud. Ineeithercase, air bubbles can cause overheating, and fluid oxidation, which can interfere with normal valve, clutch, and brake operation. Foaming can also result in fuid escaping from the transaxle vent where it may be mistaken for a leak.AUTOMATIC TRANSAXLE SYSTEM Also check the condition of the transaxle fluid. If the fluid smells as fitis burning, itmeans thatthe fluid has been ontaminated by fine particles from the bushes ‘and friction material, a transaxle overhaul may be nec- essary. Inspect the condition of fluid on the oillevel gauge. For the detail check, drain some ofthe oil fuid out of the ‘pump and then inspect the condition ofthe oil fluid ‘After checking, insert the oil level gauge into the oll filler tube securely. = -_, | / ib When new, automatic transaxle fluid should be red, The red dve is added so the assembly plant can iden- tify tas transaxle fluid and distinguish it from engine il or antifreeze. The red dve, which is not an indica- tor of fluid quality, is not permanent. As the vehicle is driven the transaxle fluid will begin to look darker. The color may eventually appear light brown. But, the transaxle should be overhauled under the following conditions. + If there is a “burning*door + If the fluid the color has become noticeably blacker. + Ifthere is a noticeably excessive amount of metal Particle in the fluid. AT -49 HYDRAULIC PRESSURE TEST 4. Warm up the engine until the automatic transaxle fluid temperature is 80~100°C(176~212'F) 2, Jack up the vehicle so that the wheels are free to turn, 3. Connect the engine tachometer. 4. Connect the oll pressure gauge(09462-21500) and the oll pressure gauge adapter(09452-21002, 09452- 21001) to each pressure discharge port, But use the gauge(30kg/om?) when measuring the reverse pres- sure, front clutch pressure and low reverse brake pressure. 1 Reducton pressure 2. Kickdown servo pressure 8. Roar clutch proseure 4 Front euch pressure 5. End cluen prosaure 8. Dampor euch protease prossure 5. Ifa value is outside the standard range, correct the problem while referring to the hydraulic pressure test diagnosis table.AT -50 AUTOMATIC TRANSAXLE (A4AF3) STANDARD HYDRAULIC PRESSURE TEST No.| Select Jengine| shit |eauc- | Servo | Rear | Front | ena | Low & | ToraUe | Damper speed | posi- tion | apply | clutch | clutch | clutch verse | con | clutch (rpm) | tion res res res res res- res tion Sure | Sure | Sure | ‘sue | Sire | pres ) pres | Sine 2 | ewien | 2500] 4 | eines, | era (ooo, 26 8rd susan | aus-oes 4-083 ere-ce7 vescrag | Yaacen | acres) | seein) aoth ard | wee | esa | eae were 4p O | 2800) gear | SY [fortes | Sees, . . fake NOTE "is 0.2(0.3)kg/om* or loss and *()* is the ro- ‘SW-ON : Turn the overdrive control switch ON. ‘SW-OFF:: Turn the overdrive control switch OFF The hydraulic pressure may be more than stan- dard value at the ambient temperature.AUTOMATIC TRANSAXLE SYSTEM DRIVE SHAFT OIL SEALS REPLACEMENT 41, Disconnect the drive shaft from the transaxle. 2. Using a lattip (-) screwdriver, remove the oil seal(A). Right Lett 3. Apply a coating of the transaxle fluid to the lip of the oil seal, 4, Using the special tool (09431-22100), tap the drive shaft oll seal into the transaxle, 9421-22100 TORQUE CONVERTER STALL TEST This test measures the maximum engine speed when the select lever is at the “D" or "R” position and the throttle is {fully opened to test the operation of the torque converter overunning clutch and the holding ability of clutch and brake inthe transaxle. NOTE Do not let anybody stand in front of or behind the vehicle while this test is being carried out. 1. Check the automatic transaxle fluid level and temper- ature and the engine coolant temperature. + Fluid level : At the HOT mark on the cil level ‘gauge + Fluid temperature : 80-90°C (176~194°F) + Engine coolant temperature 80-80°C (176-194°F) 2. Apply chocks to both rear wheels. 3. Connect the engine tachometer, 4, Pull the parking brake lever on, with the brake pedal fully depressed. 5. Start the engine. 6. Move the select lever to the °D" position, fully depress the accelerator pedal and take a reading of the maxi- ‘mum engine speed at this time. CAUTION + The throttle should not be left fully open for any more than 5 seconds. + Ifcarrying out the stall test two or more times, move the select lever to the "N" position and run the engine at 1,000 r/min to let the auto- ‘matic transaxle fluid cool down before carry- jing out subsequent tests. + Move the select lever to the “R position and carry out the same test again. ‘Stall rpm : 2,400-2,800 RPMAT 52 AUTOMATIC TRANSAXLE (A4AF3) 7. Moe the select lever to the same test again, position carry out the 1) "Stall speed above specification in If stall speed is higher than specification, the rear clutch or overrunning clutch of the transaxle is, slipping. In thiscase, perform a hydraulic test to locate the cause of slippage 2). Stall speed above specification in "R If the stall speed is higher than specification, the front clutch of the transaxle or low & reverse brake is slipping. In this case, perform a hydraulic test to locate the cause of slippage. 3) Stall speed above specification in *D" and "R" It the stall speed is lower than specification, insuf- ficient engine output or a faulty torque converter is suspected.AUTOMATIC TRANSAXLE SYSTEM AT 53 DTC P0707_ TRANSAXLE RANGE SWITCH - NO INPUT COMPONENT LOCATION | sss GENERAL DESCRIPTION exescsos ‘The Transaxle range switch sends the shift lever position information to the PCM using a 12V (battery voltage) signal. When the shif ever isin the D (Drive) position the output signal of transaxle range switch is 12V and in all other positions the voltage is OV. The PCM judges the shif lever position by reading all signals, for the transaxle range switch, simulta- neously, DTC DESCRIPTION cssssox ‘The PCM sets this code when the transaxle range switch has no output signal for an extended period of time. DTC DETECTING CONDITION sxwoss0 DTG sategy | > Oho re sia ~ Ope hotin cto it + Engine speed = 500rpm * Fly TRANSAXLE Enable conaions |S SUtpuT Sreea(se 5) apn _ Sane snc Thresha vale | = Ne sil dtd + Recognition as previous signal + When P-D or R-D or D-R SHIFT is detected, itis regarded as N-D or N-R though " Fail Safe signal is not detected. - When sports mode S/W is ON without PRN, D-RANGE signals, itis regarded sports mode.(DTC is not set)AT 54 AUTOMATIC TRANSAXLE (A4AF3) SCHEMATIC DIAGRAM esses: [circuit Diagram] Roterto staring system aN tyeon Ionibter awten rit if Feo wai itp & ease [Harness Connector] [Connection information] Shit Lover Connection TemGoT Ne Temcoi-1 No.9) igeiton SW ¢GT) TEMCOTT NooTT TEM(GOI-1 Noat)AUTOMATIC TRANSAXLE SYSTEM MONITOR SCANTOOL DATA 5. Connect scantool to data link connector(OLC). Ignition “ON” & Engine "OFF" Monitor the "TRANSAXLE RANGE SWITCH" parameter on the scantool. Move selector lever from range to *L* range. 1.2 CURRENT DATA MTUANSARLE MANGE SU Nor FIXED nx Does "TRANSAXLE RANGE SWITCH follow the reference data? YES > Fault is intermittent caused by poor contact in the sensor's and/or PCM's connector or was repaired and PCM ‘memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contam- ination, deterioration or damage. Repair or replace as necessary and go to “Verification of vehicle repair” procedure. > Go to “Terminal 3 connector inspection” procedure. TERMINAL & CONNECTOR INSPECTION | sree: 1 Many malfunctions in the electrical system are caused by poor hamess and terminals. Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage, Has a problem been found? YES > Repair as necessary and go to "Verification of vehicle repaie" procedure, > Go to "Power supply circuit inspection” procedure.AT -56 AUTOMATIC TRANSAXLE (A4AF3) POWER SUPPLY CIRCUIT INSPECTION |e: 1. CHECK POWER TO RANGE SWITCH 41) Disconnect "TRANSAXLE RANGE SWITCH" connector. 2). Ignition "ON" & Engine "OFF. 3) Measure voltage between terminal "3" of the sensor harness connector and chassis ground. Specification : approx. B+ 2, RANGE L 2 Power supply 4 RANGE 2 5. BACK UP LAMPS IKCK-UP CAMPS 5: RANGE P 1a, RANGER 12, RANGE N 4) Is voltage within specifications? = > Go to "Signal circuit inspection" procedure. > Check that Fuse 5-10A is installed or not blown. > Check for open in harness. Repair as necessary and go to "Verification of vehicle repair" procedure. SIGNAL CIRCUIT INSPECTION tscorrse 1. Ignition *OFF* 2. Disconnect "TRANSAXLE RANGE SWITCH" and "PCM" connector. 3. Measure resistance between each terminal of the sensor harness connector and PCM harness connector as below. Specification : Shown below RANGE L 2 P R D N Pin No of “TRANSAXLE RANGE SWITCH CttNo2 | CttNo4 | cttNod | C11No.10 | C11No.1t | C11 No.12 . Cort cord Cort cont Cort Cott Pin No of "PCM" harness No.6 No.8 No.67 No.8 No.66 Not Specification o 0 0 ° 0 oAUTOMATIC TRANSAXLE SYSTEM Transat ange mate 2. RANGE L 3 Power supply 4 RANGE 2 2. BACK-UP LAMPS. Power supply 11, RANGED. 2. RANGE N 185, Range D input signal 18, Range R input ign 51, Range N input sgl 68, Range L input signa {7 Ranga P input sgnal 19, Range 2 input signal 4, Is resistance within specifications? YES > Go to "Component inspection’ procedure co > Check for open in harness, Repair as necessary and go to “Verification of vehicle repai procedure. COMPONENT INSPECTION | ssn 41. Ignition OFF” 2, Remove "TRANSAXLE RANGE SWITCH 3. Measure the resistance between each terminal of the transaxle range switch. Specification : approx. 0 © Pome suppy RANGE 2 3 5 BACK-UP LAMPS BACK-UP LAMPSAT -58 AUTOMATIC TRANSAXLE (A4AF3) 2 ontirity check table | 4. Is resistance within specifications? = > Substitute with a known-good PCM and check for proper operation. Ifthe problem is corrected, replace PCM as. necessary and then go to "Verification of vehicle repair" procedure. > Replace "TRANSAXLE RANGE SWITCH’ as necessary and go to "Verification of vehicle repair” procedure, VERIFICATION OF VEHICLE REPAIR After a repair, its essential to verify that the fault has been corrected, 1. Connect scan tool and select iagnostic Trouble Codes(DTCs)" mode. 2. Using a scantool, clear DTC. 3. Operate the vehicle within DTC enable conditions in general information 4, Are any DTCs present? YES > Go to the applicable troubleshooting procedure, >» System performing to specification at this time.AUTOMATIC TRANSAXLE SYSTEM AT 59 DTC P0708 TRANSAXLE RANGE SWITCH - MULTI-INPUT COMPONENT LOCATION | = Refer to DTC P0707. GENERAL DESCRIPTION Refer to DTC P0707. DTC DESCRIPTION Refer to DTC P0707, DTC DETECTING CONDITION Item Detecting Condition & Fail Safe Possible cause DTC Strategy : ‘Check for multiple signals Enable Conditions Engine speed > 5007pm + OUTPUT SPEED(PG-8) = Orpm Threshold value | + Multiple signal Diagnostic Time | + More than 30sec Fail Safe Recognition as previous signal ~ When signal is input “D" and "N" at the same time, PCM regards it as "N" RANGE. - After PCM reset, ifthe if the PCM detects ‘multiple signal or no signal, then it holds the rd gear position * Open or short in TRANSAXLE RANGE ‘SWITCH + Faulty TRANSAXLE RANGE SWITCH + Faulty POM SCHEMATIC DIAGRAM Refer to DTC P0707. MONITOR SCANTOOL Refer to DTC P0707. TERMINAL & CONNECTOR INSPECTION Refer to DTC P0707. DATAwT -60 AUTOMATIC TRANSAXLE (A4AF3) POWER SUPPLY CIRCUIT INSPECTION | ssn 1. Disconnect "TRANSAXLE RANGE SWITCH" connector. 2. Ignition "ON" 2 Engine “OFF 3. Measure voltage between each terminal of the sensor harness connector and chassis ground. Specification : Shown below TERMINAL (erty 2 3 4 5 6 7 8 9 wo | nm | tz ‘SPECIFI- carn | oO | t2v | ov | ov | ta | ov | ov | ov | ov | ov | ow 5 BACK-UP LAMPS 4, Is voltage within specifications? YES > Go to “Signal circuit inspection” procedure. > Check for short in harness. Repair as necessary and go to "Verification of vehicle repair” procedure.AUTOMATIC TRANSAXLE SYSTEM AT 61 SIGNAL CIRCUIT INSPECTION | crcsex 1. Ignition “OFF. 2. Disconnect "TRANSAXLE RANGE SWITCH" and "PCM" connector. 3. Measure resistance between each terminals of the sensor harness to check for Short Specification = Infinite Sa ti 6 4 RANGEL Power aoe BACKUP LAMPS BACKUP LAMPS RANGE >. 10: RANGE R 4. Is resistance within specifications? > Go to "Component inspection’ procedure. > Check for open in harness. Repair as necessary and go to "Verification of vehicle repair" procedure, COMPONENT INSPECTION Refer to DTC P0707. VERIFICATION OF VEHICLE REPAIR tise Refer to DTC P0707.AT 62 AUTOMATIC TRANSAXLE (A4AF3) DTC P0711_ TRANSAXLE FLUID TEMPERATURE SENSOR RATIONALITY COMPONENT LOCATION | sxaseso GENERAL DESCRIPTION ‘The automatic transmission fluid(ATF) temperature sensor is installed in the valve body. This sensor uses a thermis- tor whose resistance changes according to the temperature changes, The PCM supplies a SV reference voltage to the sensor, and the output voltage of the sensor changes when the ATF temperature varies. The automatic transmission {luid(ATF) temperature provides very important data for the PCM's control ofthe torque converter clutch, and is also used for many other purposes. DTC DESCRIPTION excrase ‘This DTC code is set when the ATF temperature output voltage is lower than the value generated by thermistor resistance, in a normal operating range, for approximately 1 second or longer. The PCM regards the ATF temperature as fixed at a value of 80°C(176°F), if this DTC is detected,AUTOMATIC TRANSAXLE SYSTEM DTC DETECTING CONDITION excsecs AT 63 tem Detecting Condition & Fail Safe Possible cause DTC Strategy * Check for ground short + ATF Temp. at IG ON> 48°C(113°F) + (ATF Temp. at IG OFF - Coolant Temp. at Enable Conditions IG ON) > 30°C(86"F) + The variation of coolant temp, > 5°C(41"F) + Coolant temp. at IG ON >-20°C(-4°F) + (ATF Temp. at IG ON - Coolant Temp. at Threshold value IG ON) > 10°C(60°F) Diagnostic Time | + More than 1 seo * Learning control and Intelligent shift are inhibited Fall Safe + Fluid temperature is regarded as 80°C(176°F) * Sensor signal circuit is short to ground + Faully sensor + Faulty PCM SPECIFICATION | csreose Tomp.(°C(°F)] Resistance(k) Temp.°C("F)] Resistance(k::) -40(-40) 139.5 80(176) 1.08) =20(-4) a77 7100(212) 0.63 0(32) 186 120(248) 0.38 20(68) 4 140(284) 0.25 40(104), 38 160(320) 0.16 60(140) 1.98)