Escolar Documentos
Profissional Documentos
Cultura Documentos
Service
Service
Service
170V7
Horizontal Frequency
30- 83KHz
TABLE OF CONTENTS
Description Page Description Page
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
Revision List
2
17 LCD Color Monitor 170V7
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create
shock, fire,
or other hazards.
Under no circumstances should the original design be modified or altered without written permission from Philips.
Philips
assumes no liability, express or implied, arising out of any unauthorized modification of design.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION
OF THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the
panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment persons body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth
may damage the panel.)
3
17 LCD Color Monitor 170V7
1. Monitor Specifications
Tilt -5 25
4
17 LCD Color Monitor 170V7
CCFL Drive.
Flat Panel and
CCFL backlight
RS232 Connector
PWPC board Main Board
(Included: adapter and For white balance
inverter)
adjustment in factory
mode
Keyboard
5
17 LCD Color Monitor 170V7
3. Operation instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the
monitor. By changing these settings, the picture can be adjusted to your personal preferences.
- The power cord should be connected.
- Connect the video cable from the monitor to the video card.
- Press the power button to turn on the monitor, the power indicator will light up.
Back View
6
17 LCD Color Monitor 170V7
7
17 LCD Color Monitor 170V7
8
17 LCD Color Monitor 170V7
9
17 LCD Color Monitor 170V7
10
17 LCD Color Monitor 170V7
2) Connect to PC
(a) Turn off your computer and unplug its power cable.
(b) Connect the monitor signal cable to the video connector on the back of your computer.
(c) Plug the power cord of your computer and your monitor into a nearby outlet.
(d) Turn on your computer and monitor. If the monitor displays an image, installation is complete.
11
17 LCD Color Monitor 170V7
4. Input/Output Specification
4.1 Input Signal Connector
1 5
6 10
11 15
12
17 LCD Color Monitor 170V7
13
17 LCD Color Monitor 170V7
14
17 LCD Color Monitor 170V7
5. Block Diagram
5.1 Monitor Exploded View
15
17 LCD Color Monitor 170V7
Y
2 3
N
N
5
N
7 8
Y
N
10 11
N N
12 13
Y Y
N
14 15 16
17
N
18 19
16
17 LCD Color Monitor 170V7
1) MCU Initializes.
2) Is the EEprom blank?
3) Program the EEprom by default values.
4) Get the PWM value of brightness from EEprom.
5) Is the power key pressed?
6) Clear all global flags.
7) Are the AUTO and SELECT keys pressed?
8) Enter factory mode.
9) Save the power key status into EEprom.
Turn on the LED and set it to green color. Scalar
initializes.
10) In standby mode?
11) Update the lifetime of back light.
12) Check the analog port, are there any signals coming?
13) Does the scalar send out an interrupt request?
14) Wake up the scalar.
15) Are there any signals coming from analog port?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the message
disappears.
17) Program the scalar to be able to show the coming mode.
18) Process the OSD display.
19) Read the keyboard. Is the power key pressed?
17
17 LCD Color Monitor 170V7
Panel Interface
(CN406)
Keypad Interface
NT68623MEFG- 64
(CN403)
(Include MCU, ADC, OSD)
(U401)
SDA
SCL RXD H-SYNC
TXD RGB V-SYNC
EEPROM
Crystal 12MHz D-Sub Connector
AT24C16AN-10SU-2.7
(U403) (X401) (CN405)
DB15_SDA
DB15_SCL
EEPROM M24C02-WMN6TP
(U405)
18
17 LCD Color Monitor 170V7
19
17 LCD Color Monitor 170V7
6. Schematic Diagram
6.1 Main Board
715G1712-1
+5V
VGA-5V R485
1K 1/16W
0.1uF C409
CN405
DB15 ZD408
16
2
R441 R426 UDZS5.6B
220 1/16W 10 1K 1/16W GND_A D406
15 5 BAV99
VGA-SCL VGA-DET
9
VS 14 4 FB401 GND_A
8 ZD405 0 1/16W
ZD407 HS 13 3 B1 ZD414 B1
3
BI1
UDZS5.6B 7 UDZS5.6B UDZS5.6B
12 2 G1 C451
6 R455 CH201209T-300
11 1 R1 75 1/16W NC
GND_A
BI1-
DB15 GND_A GND_A
17
FB402
R440 GND_A 0 1/16W
220 1/16W
M_TXD
GND_A
VGA-SDA
M_RXD
0.1uF C410
ZD404
UDZS5.6B ZD406 ZD403
2
UDZS5.6B UDZS5.6B
C433 C434 GND_A D405
100pF 100pF BAV99
GND_A FB403
0 1/16W
G1
GI1
3
GND_A GND_A C452
R454 CH201209T-300
75 1/16W NC
GI1-
FB406
GND_A 0 1/16W
VGA-5V R406
D416 100 1/16W
VGA-VDD 1 VS
VSIN
0.1uF C411
3 +5V
ZD401 R435 C402
2
4.7K 1/16W R478
3
1 8 HS C453
2 A0 VCC 7 HSIN R456
A1 WP 24C02_WP CH201209T-300
3 6 VGA-SCL 75 1/16W NC
4 A2 SCL 5 VGA-SDA ZD402 R436 C430
GND SDA RI1-
UDZS5.6B 2.2K 1/16W 22pF
M24C02WMN6 FB405
GND_A 0 1/16W
GND_A
GND_A GND_A GND_A
Title
715G1712-1
Size Document Number Rev
A4 B
PHILIPS 170V-ADC Input
Date: Thursday, March 02, 2006 Sheet 5 of 5
20
17 LCD Color Monitor 170V7
MCU-VDD
VSO T0M
T0P
HSO T1M
T1P
SCL T2M
Q402
T2P
R418 10K 1/16W LEDG
SDA TCLK1M
TCLK1P
LED-Green R437 200 1/16W PMBS3906
RSTn T3M
T3P
Q404
T4M
R419 10K 1/16W LEDA IRQn
T4P
T5M
LED-Orange R438 200 1/16W PMBS3906
CVDD1V8 T5P
DVDD T6M
T6P
CVDD1V8 TCLK2M
TCLK2P
T7M
14 89 T7P
U401
102
101
100
C414 C420 C455
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
NT68623
0.1uF 0.1uF 1000pF
INT_VSO/GPO4
INT_HSO/GPO5
GPO3/AD1
GPO2/AD0
GPO6
GPO1
TCLK1P
TCLK1M
AGND
AGND
SDA
SCL
CGND
DGND
DGND
CVDD
DVDD
T0P
T1P
T2P
T3P
T4P
T5P
T6P
RSTN
IRQN
T0M
T1M
T2M
T3M
T4M
T5M
T6M
NC
NC
NC
NC
NC
GND_A MCU-VDD
103 64
ADC_VAA DVDD NC TCLK2M
104 63
NC TCLK2P
112 120 15 82 105 62 R442 R443
AGND T7M 3.3K 1/16W 3.3K 1/16W
106 61
NC T7P
C417 C418 C416 C422 C454 107 60 SDA
0.1uF 0.1uF 0.1uF 0.1uF 1000pF NC P35/T1
108 59 SCL
NC P34/T0
109 58 LEFT
NC PB3/ADC3/INTE1 +5V
GND_A GND_A 110 57 IRQN MCU-VDD
PVCC PB2/ADC2/INTE0
111 56 TX
PGND P31/TXD
112 55 HSO
ADC_VAA ADC_VAA PD6 R447 R404
113 54 RX 100K 1/16W
U403 BIN1+ P30/RXD
M24C16-MN6T MCU-VDD 114 53 4.7K 1/16W
BIN1- RSTB
1 8 115 52
A0 VCC 24C16_WP SOGI1 PA7/PWM9* MUTE
2 7
3 A1 WP 6 SCL 116 51 VOL-PWM
4 A2 SCK 5 SDA GIN1+ PA6/PWM8* C413
VSS SI 117 50 0.1uF
GIN1- PA5/PWM7*
C412 118 49
GND_A 0.1uF RIN1+ PA4/PWM6*
119 48 GND_A
RIN1- PA3/PWM5 FB412
GND_A 120 47 AUTO MCU-VDD 120 OHM VGA_3V3
ADC_VAA PA2/PWM4
121 46 MENU
ADC_GNDA PA1/PWM3
R451 75 1/16W C408 0.047uF B+ 122 45 PWR
BI1 BIN0+ PA0/PWM2 + C431
R423 150 1/16W C405 0.047uF 123 44 VSO C419 10uF/16V
BI1- BIN0- PD0 0.1uF
R445 390 1% C401 1000pF 124 43
SOGI0 MCU_VCC
R452 75 1/16W C406 0.047uF G+ 125 42
GI1 GIN0+ PC0*
R424 150 1/16W C407 0.047uF 126 41 STANDBY
GI1- GIN0- PC1* GND_A
R453 75 1/16W C403 0.047uF R+ 127 40 24C16_WP
TOUTP/VSYNCI1
PB5/DDC_SDA0*
PB7/DDC_SDA1*
RI1
PB4/DDC_SCL0*
PB6/DDC_SCL1*
RIN0+ PC2
R421 150 1/16W C404 0.047uF 128 39 BL-PWM
RI1- RIN0- PC3/PWM0
DPLL_GND
PC4/PWM1
DPLL_VDD
MCU_GND
PB0/ADC0
PB1/ADC1
+5V
HSYNCI1
VSYNCI0
TS_CLK
HYNCI0
PWM10
PWM11
CGND
DGND
OSCO
CVDD
DVDD
VREF
TEST
TCLK
OSCI
PD5
PD4
PD3
PD2
PD1
PC7
PC6
PC5
PE0
PE1
NC
NC
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
R412/NC
1
9
10K 1/16W
R409/NC
100 1/16W
BL-ON
LEDA 24C02_WP
C435 MCU-VDD
NC DVDD RSTn LEDG
DVDD GND_A
CVDD1V8
VGA-DET
HSIN
GND_A R422 C428
LCD-ON
R446 1K 1/16W 22pF R449 R448
VSIN
4.7K 1/16W 4.7K 1/16W 4.7K 1/16W
+5V R434 BL_EN R411
1M 1/16W 100 1/16W
3
BL-BRIGHT
+1V8 VGA-SDA
R420 1K 1/16W D401
X401
BAV99 9 VGA-SCL
FB409 12MHz
FB407 RIGHT R410
120 OHM 120 OHM + C429 C427 100 1/16W
C421 NC 12/7 Delete R457-0 ohm
2
R415/NC
R432 1K 1/16W Right-pwm 7 8 Left-pwm R427 1K 1/16W LEFT
10K 1/16W
M_TXD
R428 1K 1/16W Power-key 9 10
1K 1/16W
11 12 VOLUME R408 R429 Q401
13 14 100 1/16W SCL 1K 1/16W PMBS3904 BL_EN
OUT-L+ OUT-R+ 1 TX 1 SDA
15 16
OUT-L- OUT-R- 2 RX 2 R459
CON16A 3 3 STANDBY 4.7K 1/16W
4 STANDBY
R407 R450/NC
GND_A GND_A 100 1/16W CN401 VOL-PWM 4.7K 1/16W
VOLUME
CN402 NC/3PIN/2.0mm GND_A GND_A
PWR NC/4PIN/2.0mm BL-PWM
PANEL_IDX
RIGHT R460
AUTO GND_A TODEBUG 4.7K 1/16W
C415/NC
TO RS232 C436 0.1uF
C441 C437 C439 C438 C440 0.1uF
1000pF 1000pF 1000pF 1000pF 1000pF Title
715G1712-1
GND_AGND_A
Size Document Number Rev
C PHILIPS 170V-SCALER B
GND_A
Date: Thursday, March 02, 2006 Sheet 4 of 5
21
17 LCD Color Monitor 170V7
CN406
T0M 1
T0P 2
T1M 3
T1P 4
T2M 5
T2P 6
7
TCLK1M 8
TCLK1P 9
T3M 10
LVDS T3P 11
OUTPUT T4M 12
T4P 13
14
T0P T5M 15
T0M T5P 16
T1P
17
T1M T6M 18
T2P T6P 19
T2M TCLK2M 20
TCLK1P TCLK2P 21
TCLK1M T7M 22
T3P T7P 23
T3M
24
T4P
25
T4M
26
T5P
27
T5M
28
T6P
29
T6M LCD-VDD 30
TCLK2P LCD-VDD
TCLK2M
T7P
T7M
30PIN/2.0mm
GND_A
LCD-VDD
+12V
FB410
120 OHM +
C432
4.7uF/16V C423 R444
R417 0.1uF 150 1/8W
10K 1/16W
R403
100K 1/16W GND_A
Q405
R414 AO3401L
100K 1/16W
Q406
LCD-ON
PMBS3904 FB408
C424 0.1uF 120 OHM
C425
0.1uF
+5V
R472
VGA_3V3
10K 1/16W FB409/NC
120 OHM
GND_A
Title
715G1712-1
Size Document Number Rev
A4 PHILIPS 170V-PANEL OUTPUT B
22
17 LCD Color Monitor 170V7
FB703
U701 120 OHM
VOUT(TAB)
ADJ(GND)
MM1085DT33
DVDD
VIN
FB704
120 OHM
VGA_3V3
403mA
3
2
1
+5V
ADC_VAA CONNECTOR FOR
POWER/INVERTER
+ C713 +12V BOARD 2.0 mm +5V
+ C707 C705 1000pF
C701 10uF/16V 0.1uF C709
1000pF 100uF/16V
R701
D701(NC) 47 1/16W FB701
FA20-04 1 2 120 OHM
PANEL_IDX BL-ON
GND_A 3 4
BL-BRIGHT
5 6
FOR 3.3V POWER USE 7 8
9 10
11 12
D702(NC)
FA20-04 + C704 + C702
0.1uF 0.1uF
CN701 C712 C711
6x2PIN/2.0mm 100uF/25V 100uF/25V
FB705
VGA_3V3 120 OHM U702
ADJ/GND
OUTPUT
MM1117DT18
INPUT
GND_A
+1V8 FB702
120 OHM
3
2
1
138mA
CVDD1V8
+
C706 + +5V
C708 0.1uF C703
10uF/16V 0.1uF C710
100uF/16V FB706(NC)
120 OHM VGA_3V3
+12V +5V
GND_A
FB707(NC)
1 2 120 OHM
3 4
FOR 1.8V POWER USE 5 6
STANDBY
7 8
VOLUME MUTE
9 10
11 12
OUT-L+ OUT-R+
13 14
OUT-L- OUT-R-
CN702/NC
7x2PIN/2.0mm
GND_A GND_A
H1 H2 H3
1
1
1
23
17 LCD Color Monitor 170V7
L902
S901
N 1 2
R931
spotgap_NC C8B-R6H 1 2
2
2R2_1206
R900
1
C931
680K R932
2
C900 2 1 1 2
0.001uF/250V
2R2_1206
12
3.3nF/500V
2
1
2
R901 + T901
2
1
3 2 7mH 12
12
AC SOCKET R904 R905 C920 D931 + +
1
R902 BD901 1.5M/R1206 100K/1W 0.001uF/1KV MBRF10H100CT-45 C932 C933
C901 U4KB80R + 5 1000uF/25V 1000uF/25V
2
680K L903 C907 O
0.001uF/250V
1
3
F901 NR901
S902 D901 7 R935 Lie down
2
100uF/450V
L 1 2 1 2 BYT42J 8 1 2
1 R907 R910
2R2_1206_NC
FUSE 3.15A 250V SCK084 spotgap_NC C8B-R6H 15K/R1206 1.5M/R1206 6
FB901 C935
R936
BEAD 2 2 1 1 2
9
3.3nF/500V_NC 2R2_1206_NC
10
1 5VA
IC901
D918 1N4148
2
D935
1 8
1
R915 10 Q901 POWER X'FMR STPS10L45CFP + R937
C913 2 1 1 STP7NK80ZFP C936 1.8K_1/8W
TEA1532
0.1uF 2 7 C912 2200uF/16V
R918 150R
D905 2 1 2 1
3
P4KE_NC 3 6 FB902
1
R917 33K R916 1.5K 0.0022uF/400V BEAD
4 5 R920
1
C917 0.33uF/25V R955
1
R912 0.2R/1W
22K _NC D919
C914 1M TEA1532
1uF
RGP10D
2
D926
2 1
2 1
R923 8K66_1%
R926 0R
C915 R914 RGP10D
0.012uF/25V 1K24_1% 2 1
R927 4.7K_1206
2
IC902
2
R943
TCET1103 5.1K 1/10W ZD949
+ RLZ12B_NC
C927
2
68u/25V
1
2
2
R946
2
R944 110K_1%
R941 R949
9.1K/0805_1%
220
100 1/10W_NC
1
1
1
C941 0.0056uF
+12V L951
2
1 2 +12VCC
ZD975 IC941
0.8uH R945
2
RLZ5.1B KIA431A
12 + R952 R953 9.1K_1%
2
1
10 0.1uF/25V 220u/25V R951
1
9
3.3K_NC
8
1
7
6 ZD951
1
24
17 LCD Color Monitor 170V7
1
PT801
1
1 C802 1 CN831
2 7 5pF/3KV R834 OP1 2
CONN
21
+12V 6.2M 1/2W_NC
1
VDD 3 C803
4 C801 5pF/3KV R835
1
10pF/6KV 1 2 R831
22
C820 C821 R822 R823 5 8 1K
2
470uF/25V 1uF 10R 10R 6 10K_1%
R824
3
VDD C838
2
24:24:2400 7.5K_1%_NC
C811 1000pF R836
1
1uF 10K_1% D833
2
D831
R804
1
BAV70/SOT23B
2
10K 1/10W BAV99
1
R803 C822 C823 2
2
2 1 0.001uF 0.001uF R837 C860
1
1
7.5K_1% 220pF 3
1
10K/NC
R815 R811
2
R813 R829
3
R801 30K 1
3M3 33K_1%
1
10K Q801
12
Q821 0 1/10W
1
2 1 1 2N7002 R830 R833
BRIGHTNESS
2
2
S1 D1 10K_1%_NC
2
2 2 7 5pF/3KV_NC
U811 G1 D1 6.2M 1/2W
21
R802 3 6 C824 OP2
C830 1 16 4 S2 D2 5 C804 2
5PF/NC
2
10K/NC DRV1 PGND G2 D2 CN833
1000pF/NC 5pF/3KV_NC 1
2
2 15 AM9945N CONN
1
2
VDDA DRV2
2
3 14 C825
TIMER GNDA
5PF/NC
1
4 13
1
DIM CT PT802
1
1 R854 C807
2
21
560pF C806 D853 OP3 2
R806
1
C826 6 11 3 10pF/6KV C808 BAV70/SOT23B CONN
100K/NC VSEN LCT +12V
0.01uF/NC C847 4 5pF/3KV R855
1
7 10 1
2
OVPT ENA 0.022uF/25V
1
C840 C841 5 8 R851
1
2
1
1
8 9 C812 470uF/25V 1uF 6 10K_1% 3 1K
NC1 NC2
1
R816 0.1uF R812 R842 R843 R857
2
24:24:2400 R856
1
3
20K OZ9938GN 10R 10R C861 2
2
620K 1/10W
1
C831 7.5K_NC 10K_1%
1000pF
2
C846 C832 D851
2
0.33uF
1uF 0.1uF BAV99
2
2
2
VDD
2
R807
C842 R825
2 1 C843 C858
1
0.001uF 0.001uF 390pF 7.5K_1%
10K 1/10W
R849
1
1 2
1
Q841
0 1/10W
1
1 8
S1 D1
2
2 7 C810 R850 R853
G1 D1
1
1
R819 3 6 C844 5pF/3KV_NC 10K_1%_NC 1.2K
C819 1M 4 S2 D2 5 R859
5PF/NC
12
G2 D2 6.2M 1/2W OP4
0.01uF/25V
1
AM9945N C809
2
2
2
5pF/3KV_NC 2
CN853
C845 1
2
CONN
5PF/NC
1
R861 R863
PANEL_ID 2 1 Isen 2 1
PANEL_ID
1
100K_1%
1
33K 1/4W R865 R866
VDD C865
232 100K/NC
33nF
2
1
+12V Isen
2
R880
10K 1/10W
1
2 Q873 Q880
PDTA144EU 2N7002 1
2
3
C880
3
3
0.1uF/25V
2
1
R873 330 1/10W
10K 1/2W 1K 1/10W
2
2K 1/10W IN4148
2
2
C881 R881
13
2
2
2N7002 1 2 1 OP2
1
1
2
ZD874 1K 1/10W
2
C883
RLZ5.6B
C874 0.01uF 100K 1/10W
3
1uF
1
2
2N7002 1 2 1 OP3
1 1K 1/10W IN4148
2
C885 R885
0.01uF 100K 1/10W
3
Q886 D887
R888
2
2N7002 1 2 1 OP4
1
1K 1/10W IN4148
2
R887
C887
0.01uF 100K 1/10W
2
25
17 LCD Color Monitor 170V7
7. PCB Layout
7.1 Main Board
715G1712-1
26
17 LCD Color Monitor 170V7
27
17 LCD Color Monitor 170V7
28
17 LCD Color Monitor 170V7
29
17 LCD Color Monitor 170V7
30
17 LCD Color Monitor 170V7
31
17 LCD Color Monitor 170V7
8. Wiring Diagram
Panel
CN851
CN853 CN951
CN901
CN831
CN833 Main Board
CN403
AC-IN CN405
D-SUB
32
17 LCD Color Monitor 170V7
9. Mechanical Instructions
1. Back View as Fig.1
Fig.1
2. Remove base as Fig.2- Fig.3
a. Remove 1 screw for hinge cover as Fig.2
b. Remove 5 screws for base as Fig.3
Fig.2
Fig.3
33
17 LCD Color Monitor 170V7
Fig.4
Fig.5
Fig.6
34
17 LCD Color Monitor 170V7
Fig.7
Fig.8
Fig.9
35
17 LCD Color Monitor 170V7
Fig.10
Fig.11
Fig.12
36
17 LCD Color Monitor 170V7
Fig.13
Fig.14
37
17 LCD Color Monitor 170V7
38
17 LCD Color Monitor 170V7
39
17 LCD Color Monitor 170V7
No power
NG
NG
OK Replace U701, U702
NG
OK Replace X401
Replace U401
40
17 LCD Color Monitor 170V7
(2). No Picture
No picture
NG
Replace U701, U702
OK
OK NG
Replace X401
Replace U401
41
17 LCD Color Monitor 170V7
White screen
NG
Measure Q406 base X401 oscillate
is high level? waveform is normal
OK NG
OK Replace X401
NG Check Correspondent
NG component.
Check Correspondent OK
component. OK
Replace U401
Replace Panel
42
17 LCD Color Monitor 170V7
Power/Inverter Board
No power
Adapter Board
NG
NG
OK
Check AC input
OK NG
Check bridge rectified circuit and F901 circuit
NG
OK Check R907 and IC901
NG
OK Check IC901, D926, T901
43
17 LCD Color Monitor 170V7
Inverter board
No power
NG
Check adapter section
OK
NG
Check Interface section or main board
OK
NG
Check Q801
OK
Check U811 Pin1/pin15 have the output of sawtooth wave at short time
NG
Check U811 pin 5/pin6
OK NG
OK Replace U811
NG
Cut all the pin connector of Q821/Q841, check C811 (+)=12V?
NG
OK
Check Q801
OK
Replace Q821/Q841
Check PT801/PT802 pin7/pin8= 650V?
Replace PT801/PT802
44
17 LCD Color Monitor 170V7
45
17 LCD Color Monitor 170V7
46
17 LCD Color Monitor 170V7
47
17 LCD Color Monitor 170V7
Note: If it is 170s model, you can select the (for QDI panel)
or (for LPL panel)
48
17 LCD Color Monitor 170V7
49
17 LCD Color Monitor 170V7
50
17 LCD Color Monitor 170V7
51
17 LCD Color Monitor 170V7
52
17 LCD Color Monitor 170V7
Note: After installation, you must restart the PC to take the setup effect.
Connect to
the PC LPT
12V Input
53
17 LCD Color Monitor 170V7
b. Click .
c. Key in the Serial Number printed on the barcode label, then click OK
14 codes,
for example.
54
17 LCD Color Monitor 170V7
55
17 LCD Color Monitor 170V7
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
0: 00 FF FF FF FF FF FF 00 41 0C 46 08 01 01 01 01
16: 0F 10 01 03 0E 22 1B 78 EE BE B5 A3 56 48 9A 24
32: 15 50 54 BF EF 80 71 4F 81 40 81 80 01 01 01 01
48: 01 01 01 01 01 01 30 2A 00 98 51 00 2A 40 30 70
64: 13 00 52 0E 11 00 00 1E 00 00 00 FF 00 20 41 55
80: 20 20 30 30 30 30 30 31 0A 20 00 00 00 FC 00 50
96: 68 69 6C 69 70 73 20 31 37 30 56 0A 00 00 00 FD
112: 00 38 4C 1E 53 0E 00 0A 20 20 20 20 20 20 00 C8
<---Header--->
Header: 00 FF FF FF FF FF FF 00
<-x-Header-x->
<---Vendor/Product Identification--->
ID Manufacturer Name: PHL
ID Product Code: 0846
ID Serial Number: 01010101
Week of Manufacture: 15
Year of Manufacture: 2006
<-x-Vendor/Product Identification-x->
<---Color Characteristics--->
Red x: 0.6386718750
Red y: 0.3388671875
Green x: 0.2861328125
Green y: 0.6035156250
Blue x: 0.1425781250
Blue y: 0.0849609375
White x: 0.3125000000
56
17 LCD Color Monitor 170V7
White y: 0.3300781250
<-x-Color Characteristics-x->
<---Established Timings--->
Established Timings 1: BF
-720x400 @70Hz VGA,IBM
-640x480 @60Hz VGA,IBM
-640x480 @67Hz Apple,Mac II
-640x480 @72Hz VESA
-640x480 @75Hz VESA
-800x600 @56Hz VESA
-800x600 @60Hz VESA
Established Timings 2: EF
-800x600 @72Hz VESA
-800x600 @75Hz VESA
-832x624 @75Hz Apple,Mac II
-1024x768 @60Hz VESA
-1024x768 @70Hz VESA
-1024x768 @75Hz VESA
-1280x1024 @75Hz VESA
Established Timings 3: 80
-1152x870 @75Hz Apple,Mac II
<-x-Established Timings-x->
Extension Flag: 00
Checksum: C8
57
17 LCD Color Monitor 170V7
y=32920,Y>200.
2). Switch the MEM. Channel to Channel 4 (with up or down arrow on chroma 7120)
3). Adjust the R of Warm item on factory window until chroma 7120 indicator reached the value R=1005
4). Adjust the G of Warm item on factory window until chroma 7120 indicator reached the value G=1005
5). Adjust the B of Warm item on factory window until chroma 7120 indicator reached the value B=1005
6). Switch the Chroma-7120 to x, y, Y Mode, check whether the color-temperature value is within Spec.
the Spec is 6500K: x=31320, y=32920,Y>200. If not in the SPEC, repeat step 3,4,5.
Turn the Power-button off to quit and save the factory mode.
58
17 LCD Color Monitor 170V7
PCB
Part No for TPV Description Philips 12NC
CBPC780KGMP3P CONVERSION BOARD ASS'Y 9965 000 37416
PWPC1742QDR1P POWER BOARD 9965 000 37020
KEPC780KE7P KEY BOARD 9965 000 35900
Panel
59
17 LCD Color Monitor 170V7
Main Board
63
17 LCD Color Monitor 170V7
Power Board
64
17 LCD Color Monitor 170V7
R916 061L0805152 CHIPR 1.5K OHM -5% 1/10W 9965 000 36970
R873 061L0805202 CHIP 2KOHM 1/8W 9965 000 36971
R816 061L0805203 CHIPR 20KOHM -5% 1/8W 9965 000 36972
R865 061L08052320F CHIP 232OHM 9965 000 36973
R815 061L0805303 CHIP 30K OHM 1/8W 9965 000 36974
R813 061L08053302F CHIP 33KOHM 1/8W 1% 9965 000 36975
R874 061L0805331 CHIP 330 OHM 5% 1/10W 9965 000 36976
R917 061L0805333 CHIP 33KOHM 1% 1/8W 9965 000 36977
R811 061L0805335 3.3M 0805 9965 000 36978
R943 061L08055101F CHIP 5.1K OHM 1/10W 1% 9965 000 36979
R812 061L0805624 CHIP 620KOHM 5% 0805 1/8W 9965 000 36980
R825 061L0805752 CHIP 7.5K OHM 1/10W 9965 000 36981
R837 061L0805752 CHIP 7.5K OHM 1/10W 9965 000 36981
R944 061L08059101F CHIP 9.1K OHM 1/10W 1% 9965 000 36982
R945 061L08059101F CHIP 9.1K OHM 1/10W 1% 9965 000 36982
R926 061L1206000 CHIPR 0 OHM -5% 1/8W 9965 000 36067
R918 061L1206000 CHIPR 0 OHM -5% 1/8W 9965 000 36067
R907 061L1206103 CHIP 10KOHM 5% 1/4W 9965 000 36016
R904 061L1206155 1.5M/0805 9965 000 36983
R910 061L1206155 1.5M/0805 9965 000 36983
R937 061L1206182 CHIP 1.8KOHM 9965 000 36984
R931 061L1206229 CHIP 2.2OHM 5% 1/8W 9965 000 36985
R932 061L1206229 CHIP 2.2OHM 5% 1/8W 9965 000 36985
R927 061L1206472 CHIP 4.7KOHM 5% 1/4W 9965 000 36986
R902 061L1206684 CHIPR 680K OHM -5% 1/8W 9965 000 36024
R901 061L1206684 CHIPR 680K OHM -5% 1/8W 9965 000 36024
R900 061L1206684 CHIPR 680K OHM -5% 1/8W 9965 000 36024
C838 065G080510231 1000PF 50V NPO 9965 000 36991
C861 065G080510231 1000PF 50V NPO 9965 000 36991
C822 065G080510232 CHIP 1000P 50VX7R 0805 9965 000 36038
C823 065G080510232 CHIP 1000P 50VX7R 0805 9965 000 36038
C842 065G080510232 CHIP 1000P 50VX7R 0805 9965 000 36038
C843 065G080510232 CHIP 1000P 50VX7R 0805 9965 000 36038
C887 065G080510322 CHIP 0.01UF 25V X7R 0805 9965 000 36039
C885 065G080510322 CHIP 0.01UF 25V X7R 0805 9965 000 36039
C883 065G080510322 CHIP 0.01UF 25V X7R 0805 9965 000 36039
C881 065G080510322 CHIP 0.01UF 25V X7R 0805 9965 000 36039
C819 065G080510322 CHIP 0.01UF 25V X7R 0805 9965 000 36039
C913 065G080510422 0.1UF -10% 25V X7R 080 9965 000 36040
C955 065G080510422 0.1UF -10% 25V X7R 080 9965 000 36040
C951 065G080510422 0.1UF -10% 25V X7R 080 9965 000 36040
C812 065G080510422 0.1UF -10% 25V X7R 080 9965 000 36040
C914 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073
C841 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073
66
17 LCD Color Monitor 170V7
C846 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073
C874 065G080510522 CHIP 1UF 25V X7R 0805 9965 000 36073
C915 065G080512322 CHIP 12NF 25V X7R 0805 9965 000 36992
C860 065G080522122 CHIP 220PF 25V X7R 0805 9965 000 36993
C847 065G080522322 CHIP 0.022UF 25V X7R 0805 9965 000 36043
C831 065G080533132 CHIP 330P 50V X7R 0805 9965 000 36994
C865 065G080533332 CHIP 0.033UF 50V 9965 000 36995
C917 065G080533422 0.33UF -10% 25V X7R 0805 9965 000 36074
C858 065G080539131 CHIP 390PF 50V 9965 000 36996
C813 065G080556131 CHIP 560PF 50V NPO 0805 9965 000 36997
C941 065G080556221 5600PF/25V/NPO/J 9965 000 36998
D851 093G6433 DIO SIG SM BAV99 (PHSE)R 9965 000 35994
D831 093G6433 DIO SIG SM BAV99 (PHSE)R 9965 000 35994
D833 093G6442PP BAV70 SOT-23 9965 000 35995
D883 093G6444S LL4148WP 9965 000 36035
ZD874 093G39S24T RLZ 5.6B LLDS 9965 000 36079
ZD975 093G39S25T RLZ5.1B LLDS 9965 000 37002
IC941 056G15810T AZ431AZ-AE1 9965 000 36101
R952 061G17210052T 100HM 5% 1/4W 9965 000 36987
R915 061G17210052T 100HM 5% 1/4W 9965 000 36987
R871 061G17210352T CFR 10KOHM -5% 1/4W 9965 000 36988
R861 061G20010452T 100K OHM 1/4W 1% 9965 000 36989
R863 061G20033352T 33KOHM 1% 1/4W 9965 000 36990
R859 061G212Y625KT MGFR 6.2MOHM -5% 1/2W 9965 000 36083
R839 061G212Y625KT MGFR 6.2MOHM -5% 1/2W 9965 000 36083
C920 065G1K1025T 1000PF/1KV 9965 000 36999
C931 065G517K3322T 3.3NF 500V 9965 000 37000
C927 067G3056804KT ELCAP 68UF M 25V 105 KINGNICHI 9965 000 37001
C952 067G215B2214KT LOW E,S,R 220UF -20% 25V 9965 000 36076
FB905 071G5523S BEAD 9965 000 37004
FB901 071G5529 FERRITE BEAD 9965 000 36053
F902 084G554 FOSE 382-5A 250V SICKMANN 9965 000 37005
F901 084G557GP FUSE 3.15A 250V 9965 000 37006
ZD951 093G39A3552T ZENER DIODE P6KE8.2A ZOWIE 9965 000 37007
D926 093G6038T52T FR103 9965 000 36095
D919 093G6038T52T FR103 9965 000 36095
67
17 LCD Color Monitor 170V7
Key Board
68
17 LCD Color Monitor 170V7
69
17 LCD Color Monitor 170V7
CONTENT
1 FOREWORD
2 PRODUCT PROFILE
2.1 LCD
2.2 SCANNING FREQUENCIES
2.3 AMBIENT TEMPERATURE
2.4 REGULATORY COMPLIANCE
3 ELECTRICAL CHARACTERISTICS
3.1 INTERFACE SIGNALS
3.2 INTERFACE
3.3 TIMING REQUIREMENT
3.4 HORIZONTAL SCANNING
3.5 VERTICAL SCANNING
3.6 POWER INPUT CONNECTION
3.7 POWER MANAGEMENT
3.8 DISPLAY IDENTIFICATION
3.9 USB HUB
4 VISUAL CHARACTERISTICS
4.1 TEST CONDITIONS
4.2 BRIGHTNESS
4.3 IMAGE SIZE
4.4 BRIGHTNESS UNIFORMITY
4.5 CHECK CROSS TALK (S)3
4.6 WHITE COLOR ADJUSTMENT
5 MECHANICAL CHARACTERISTICS
5.1 CONTROLS
5.2 UNIT DIMENSION / WEIGHT
5.3 TILT AND SWIVEL BASE
5.4 TRANSPORTATION PACKAGES
6 ENVIRONMENTAL CHARACTERISTICS
6.1 SUSCEPTIBILITY OF DISPLAY TO EXTERNAL ENVIRONMENT
6.2 TRANSPORTATION TESTS
6.3 DISPLAY DISTURBANCES FROM EXTERNAL ENVIRONMENT
6.4 DISPLAY DISTURBANCES TO EXTERNAL ENVIRONMENT
7 RELIABILITY
7.1 MEAN TIME BETWEEN FAILURES
8 QUALITY ASSURANCE REQUIREMENTS
8.1 ACCEPTANCE TEST
9 SERVICEABILITY
10 PHILIPS FLAT PANEL MONITORS PIXEL DEFECT POLICY
70
17 LCD Color Monitor 170V7
. CE ENVIRONMENTAL POLICY
. SOG SUPPORT
. TCO 03
. RoHS required
. WEEE required
71
17 LCD Color Monitor 170V7
1. FOREWORD
This specification describes a 17 wide SXGA multi-scan color TFT LCD monitor with
max. resolution up to 1280*1024/ 75 Hz non-interlaced. All optical characteristics (including WHITE-D, Brightness,
and so on) are determined according to panel specification after warming up approximate 30 minutes that brightness
stability is optimal, and follow strictly after panel specification.
2. PRODUCT PROFILE
This display monitor unit is a color display monitor enclosed in PHILIPS global styling cabinet, which has an
integrated foldable base.
2.1 LCD
Hor. : 30 83 KHz
Ver. : 56 - 76Hz
Video dot rate : 140MHz
Power input : 90-264 V AC, 50/60 2 Hz
Power consumption : 36W (max.), 30W (typ.)
Functions :
(1) D-SUB: analog R/G/B separate inputs, H/V sync separated, Composite (H+V) TTL level, SOG
sync
(2) DVI_A: NA
(3) DVI_D: NA
72
17 LCD Color Monitor 170V7
3. Electrical characteristics
Sync. : Separate sync TTL level , input impedance 2.2k ohm terminate
Hsync Positive/Negative
Vsync Positive/Negative
NA
3.2 Interface
73
17 LCD Color Monitor 170V7
NA
Adjustable functions:
MONITOR SETUP
Exit
Brightness & Contrast Brightness
Contrast
Color Original Color, 9300K,6500K,
sRGB, User Define
Position Horizontal
Vertical
Remark : < to Adjust > ---------- < to Move > - < to Confirm >
Remark : Color Temperature factory default setting = see 170V7 SKU.
Remark: Language default to English, and Language couldnt be reset.
NA
74
17 LCD Color Monitor 170V7
Item H.Freq. Mode Resolutio V.Freq. Item H.Freq. Mode Resolution V.Freq.
(KHz) n (Hz) (KHz) (Hz)
1024x76
9 48.363 VESA 60.004 19
8
1024x76
10 56.476 VESA 70.069 20
8
MODE NO. 1 2 3 4
RESOLUTION 640 x 350 720 x 400 640 x 480 640 x 480
75
17 LCD Color Monitor 170V7
MODE NO. 5 6 7 8
RESOLUTION 640 x 480 640 x 480 640x480 800 x 600
MODE NO. 9 10 11 12
RESOLUTION 800 x 600 800 x 600 800 x 600 800 x 600
Dot clock(MHz) 40 50 49.498 56.251
76
17 LCD Color Monitor 170V7
MODE NO. 13 14 15 16
RESOLUTION 832 x 624 1024 x 768 1024 x 768 1024 x 768
Dot clock(MHz) 57.28 65 75 78.75
MODE NO. 17 18 19 20
RESOLUTION 1024 x 768 1024 x 768 1152 x 864 1152 x 864
Dot clock(MHz) 83.096 94.5 79.9 94.5
77
17 LCD Color Monitor 170V7
MODE NO. 21 22 23 24
RESOLUTION 1152 x 864 1152 x 870 1152 x 900 1152 x 900
MODE NO. 25 26 27 28
RESOLUTION 1280 x 960 1280 x 960 1280 x 1024 1280 x 1024
78
17 LCD Color Monitor 170V7
MODE NO. 29 30 31 32
RESOLUTION 1280 x 1024 1280 x 1024 1280 x 1024 960x720
MODE NO. 33
RESOLUTION 960X720
Fh 56.4kHz
A ( us ) 17.73(1284 dots)
B ( us ) 1.44(104 dots)
C ( us ) 2.21(160 dots)
D ( us ) 13.256(960 dots)
E ( us ) 0.780(56 dots)
Fv 75Hz
O (ms ) 13.333(752 lines)
P ( ms ) 0.053(3 lines)
Q (ms ) 0.5(28 lines)
R ( ms ) 12.766(720 lines)
S ( ms ) 0.0184(1 lines)
SYNC. H/V -/ +
POLARITY
SEP . SYNC Y
79
17 LCD Color Monitor 170V7
The monitor must comply with the Microsoft On Now specification, with two power management states,
as defined by the VESA DPMS document. The monitor must appropriately display the DPMS state.
In accordance with VESA Display Channel Standard Ver.1.0 and having DDC 2B capability
NA
4. Visual characteristics
Unless otherwise specified, this specification is defined under the following conditions.
(3) Warm up: more than 30 minutes after power on with signal supplied.
4.2 Brightness
>=250 nits (at panel color temperature, at center of the screen, set contrast and brightness at maximum. )
4.3 Image size
Actual display size 337.920 x 270.336mm
80
17 LCD Color Monitor 170V7
Set contrast at 100% and turn the brightness to get average above 200 nits at centre of the screen.
Apply the Fig 1; it should comply with the following formula:
B_min
X 100% >75%
B_max
There are three factory preset white color 9300K, 6500K, sRGB.
Apply full white pattern, with brightness in 100 % position and the contrast control at 50 % position.
The 1931 CIE Chromaticity (color triangle) diagram (x,y)
coordinate for the screen center should be:
Product spec.
9300K CIE coordinates X = 0.283 0.02 Y = 0.297 0.02
5. Mechanical characteristics
5.4 The gap between Panel and front bezel < 0.8 mm
81
17 LCD Color Monitor 170V7
5.7 Resins
RoHS required
WEEE required.
Rohs required
WEEE require
Tooling to be designed to minimize cosmetic defects induced by molding process (sink, blush, weld lines,
gate marks, ejector marks, etc.).
Painting to cover up cosmetic defects due to molding is strongly discouraged.
All Plastics to be Flame Retardant UL 94-V0 or Better (if monitor weighs less than 18kg; UL94-V0 is OK).
All major plastic parts (bezel, back cover ) need to be molded from same resin.
The texture area and texture no should follow Philips make-up sheet.
The exterior surfaces shall have a uniform texture.
Philips must approve the mold texturing.
Detail document for texture refer to UAN-D249.
< = 20 gloss units
5.13 Label
5.15 Transportation
82
17 LCD Color Monitor 170V7
6. Environmental characteristics
The following sections define the interference and susceptibility condition limits that might occur
between external environment and the display device.
83
17 LCD Color Monitor 170V7
Operating
- Temperature : 0 to 35 degree C
- Humidity : 80% max
- Altitude : 0-3658m
- Air pressure : 600-1100 mBAR
Storage
- Temperature : -20 to 60 degree C
- Humidity : 85% max ( < 40 )
- Altitude : 0-12192m
- Air pressure : 300-1100 mBAR
Note: recommend at 5 to 35C, Humidity less than 60 %
7. Reliability
System MTBF (Excluding the LCD panel and CCFL) : 50,000 hrs
9. Serviceability
The serviceability of this monitor should fulfill the requirements which are prescribed in UAW-0346 and must be
checked with the check list UAT-0361.
84
17 LCD Color Monitor 170V7
256
P2 P6 P3
512
P7 P1 P8
768
P4 P9 P5
85
17 LCD Color Monitor 170V7
1/6
1/2
YA
1/2
1/3
1/2
1/3
YB
1/2
1/3
86