Escolar Documentos
Profissional Documentos
Cultura Documentos
S2202E01
Revision A
November 28, 2002
SERVICE MANUAL
MA203DT / MA203DT A
Copyright I I YA M A C O R P O R AT I O N
710-1 Kitaowaribe, Nagano-shi 381-0014 JAPAN
[ Revision Record ]
1. The design of this product contains special hardware, many circuits and components specially for safety pur-
poses. For continued protection, no changes should be made to the original design unless authorized in writing
by the manufacturer. Replacement parts must be identical to those used in the original circuits. Service should
be performed by qualified personnel only.
2. Alterations of the design or circuitry of the products should not be made. Any design alterations or additions will
void the manufacturer's warranty and will further relieve the manufacturer of responsibility for personal injury or
property damage resulting therefrom.
3. Many electrical and mechanical parts in the products have special safety-related characteristics. These charac-
teristics are often not evident from visual inspection nor can the protection afforded by them necessarily be
obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which
have these special safety characteristics are identified in the parts list of Service manual. Electrical compo-
nents having such features are identified by mark # on the schematics and ! on the parts list in Service
manual. The use of a substitute replacement which does not have the same safety characteristics as the
recommended replacement part shown in the parts list of Service manual may create shock, fire, or other
hazards.
5. The high voltage applied to the picture tube must conform with that specified in Service manual. Excessive high
voltage conditions should be kept to a minimum, or should be prevented. If severe arcing occurs, remove the AC
power immediately and determine the cause by visual inspection (incorrect installation, cracked or melted high
voltage harness, poor soldering, etc.) To maintain the proper minimum level of soft X-ray emission, components
in the high voltage circuitry including the picture tube must be the exact replacements or alternatives approved
by the manufacturer of the complete product.
6. Isolation Check
(Safety for Electrical Shock Hazard)
After reassembling the product always perform an isolation check on the exposed metal parts of the cabinet
(video input and output terminals, control knobs, screwheads, control shafts, etc.) to be sure the product is safe
to operate without danger of electrical shock.
i
Alternate Check Method
Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Use an
AC voltmeter having 1,000 ohms per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor
paralleled by a 0.15uF AC-type capacitor between an exposed metal part and a known good earth ground (water
pipe etc.).
Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed
metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage
across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Any voltage measured
must not exceed 2.45V AC(r.m.s.). This corresponds to 3.5mA AC(r.m.s.).
AC VOLTMETER
(HAVING 1,000/V OR MORE SENSITIVITY)
0.15uF AC-TYPE
ii
1. SET-UP ADJUSTMENTS
The following adjustments should be made when a complete realignment is required or a new picture tube is
installed.
<Preparation>
1. Place the monitor without tilting.
2. Connect the signal cable from the signal generator to the monitor.
3. Face the CRT screen to east so as not to be influenced by magnetic force.
4. Turn ON the Power Switch, and degauss the entire screen with degausser.
5. Perform adjustment by setting the brightness to center and the contrast to maximum, except where
specifically indicated.
6. Receive MODE 5 and turn ON the Power Switch. Perform adjustment after a warm-up of at least an
hour.
7. Adjustment data is automatically saved in the memory when the on screen display disappears or
another signal is received.
Note: This monitor should be checked and adjusted by connecting it to a signal generator, then
entering and running the timing charts both below and of Chapter 2.
* The resolutions are only for your reference when using Leader 1604A.
-1-
ADJUSTMENT MODE
There are two different modes available to adjust the monitor as described below. The adjustment with o in front
of the title are only available under User Mode. The adjustments with n in front of the title are only available under
Factory Mode. You can perform the other adjustments by either User or Factory Mode. Please change the mode
as required.
USER MODE:
Turn ON the Power Switch and you are in the User Mode.
FACTORY MODE: There are two ways to enter the Factory Mode.
1. Turn OFF the Power Switch. Short between pins 2 and 4 of RS connector on the PWB-MAIN with
a short-connector. Turn ON the Power Switch and you are in the Factory Mode. The following Factory
Mode Menu appears on the screen when you press the MENU Button. Turn OFF the Power Switch and
remove the short-connector from RS connector to exit.
PWB-MAIN
short
RS
CRT RS
connector
CRT face
2. In the adjustment menu, select "Function" on the Main Menu and then select "Language" on the Sub-Menu.
Follow the flow chart below and you are in the Factory Mode. Turn OFF the Power Switch to exit.
R C HD B C DP DH VD
VS VC COLOR T1 T2
F
f
-2-
EXTERNAL DEGAUSS
Make sure you disable the Bottom-right, Top-right, Top-left, Bottom-left, and rrc settings before performing the
external degauss. Follow the procedure below depending on the adjustment mode you are in.
PROCEDURE
o USER MODE
1) Select Degauss and press the MENU Button so that the Bottom-right, Top-right, Top-left, Bottom-left,
and rrc will be disabled.
2) Degauss the entire screen with degausser while the Degauss is activated (approx. 6 seconds).
n FACTORY MODE
1) Select Degauss and press the MENU Button so that the Top-left, Bottom-left, Top-right, Bottom-right,
and NS will be disabled.
2) Confirm that the OSD stays displayed on the screen.
Note: If the OSD disappears, restart from 1).
3) Degauss the entire screen with degausser.
-3-
1-1. 80V-ADJ adjustment [PWB-MAIN]
Voltage
1) Receive a cross-hatch inverted signal of MODE 6 when applying the AC
voltage of 11010V.
2) Connect the DC voltmeter between CONNECTOR TP and GND (chassis).
3) Adjust the voltage to DC 801.0V with VR901 (80V-ADJ).
VR901 80V-ADJ
Note: SCREEN VR should not be turned after the adjustment above. T501(FBT)
**** 30 Monitor
2) Select Degauss and press the MENU Button. front
-4-
n 1-5. FH-LIMITER confirmation
1) Receive a cross-hatch inverted signal of fH 29.2kHz.
2) Confirm that the picture disappears. Also, make sure the horizontal
oscillation frequency is within the specified range: 59-61kHz.
3) Receive fH 30.9kHz and confirm that the picture is synchronized.
4) Receive fH 112.5kHz and confirm that the picture disappears. Also, make
sure the horizontal oscillation frequency is within the specified range above.
5) Receive fH 78.8kHz and confirm that the picture is synchronized.
6) Turn OFF the power of signal generator and confirm that the picture
disappears. Also make sure the horizontal oscillation frequency is within
the specified range above.
7) Remove the frequency counter.
-5-
n1-9. H-CENT adjustment [PWB-MAIN]
1) Receive a cross-hatch inverted signal of MODE 7.
2) Adjust the horizontal size and position of the picture roughly with the front
buttons.
Back-raster
3) Maximize the brightness so that the back-raster appears on the screen.
4) Set Jumper 34,35(Left), None(Center), Jumper 33,36(Right) so that A and
A Picture B
B in the right hand side figure are almost equal.
5) Return the brightness to center indication (adjustment range: 128).
Bezel
3) Correct the side distortion with the front buttons so that X of the right Bezel
hand side figure is as follows: | X | </= 3.0mm.
X X X X
H / V-size Pinbalance
H / V-position Parallelogram
Pincushion Side pin Top / Bottom
Pincushion
Trapezoid Pinbalance Top / Bottom
-6-
o1-13. RESET confirmation
1) Receive a cross-hatch inverted signal of MODE 5.
2) Change the horizontal position (H-Position) roughly with the front buttons.
3) Perform Reset.
4) Confirm that the adjustment data above is reset to the factory setting.
WARNING: Do not change the horizontal and vertical sync signal or the fre-
quency while the automatic COLOR adjustments are underway.
cd/m fL
Color analyzer setting: Luminance unit switch
l Luminance unit switch: cd/m2
l B.P.S. DIP switch: 9600 (1000) 1
l Turn ON the color analyzer switch and press 0-CAL switch before use. 0
B. P. S. DIP switch
<CONTRAST>
The specified contrast ranges are as follows: OPQ ON: 1255cd/m2
OPQ OFF: 1108cd/m2
Note: In case that the contrast is not within the specified range above,
repeat 4) to 7).
8) The OSD disappears.
9) Turn OFF the Remote Switch of the color analyzer.
10) Turn OFF the Power Switch and remove the short-connector.
Note: The adjustments above can be repeated by turning OFF and ON the Power Switch.
-7-
n 1-15. GRAY SCALE confirmation
1) Receive a 16-gradation gray scale signal of MODE 5.
2) Make sure the 15th gradation on the gray scale is barely visible when the
16th gradation (back raster) is not visible at all.
-8-
n 1-20. RASTER REGULATION (DYNAMIC) confirmation Back-raster
10) Repeat the FOCUS adjustments until the focus with red, green and blue
Fig.3
is optimum.
-9-
n 1-23. ITC (Integrated Tube Component) adjustments
The following ITC adjustments should be made only when a new picture tube is installed*1, or convergence is poor.
All set-up adjustments above-mentioned must be completed before any further ITC adjustment is attempted.
Perform the following adjustments by setting H-convergence and Tilt-dy to center indication.
Notes: *1. See Chapter 5 concerning parts list for the ITC adjustments.
*2. PURITY MAGNET and 2-POLE MAGNET should not be turned during the ITC adjustments.
XV PURITY MAGNET*2
4-POLE MAGNET
6-POLE MAGNET
YV(a) YH(t)
+ +
+ DEFLECTION
TRD YOKE
XV
LOCKING RING
SEPARATOR
CRT face
BOW MAGNET
DIFFERENTIAL
COIL
2) Adjust the 4-POLE MAGNET so that red and blue beams converge on the
center cross lines.
R,B G
3) Add green to the red and blue cross-hatch signal. G
4) Adjust the 6-POLE MAGNET so that red and blue beams converge with R,B
green beam on the center cross lines.
5) Repeat the adjustment until red, blue and green beams converge each R,G,B
other.
R,G,B
6) Fix the 4-POLE MAGNET and the 6-POLE MAGNET by turning the
LOCKING RING.
7) Mark the 4-POLE MAGNET and the 6-POLE MAGNET with paint marker
(090Z029A01) so that adjusted position is understandable.
R,B
R,B
R,B
- 11 -
1-23-6. YH adjustment
YH(t)
1) Receive a red and blue cross-hatch signal. B R
R,B
Ferrite
10
Ferrite
90
70
(in mm)
(890Z003A03) (890Z003A05)
*Ferrite sheet
- 12 -
2. TIMING CHART
Video
Sync
B C D E P Q R S
H-parameters V-parameters
A A: Total period O O: Total period
B: Sync.width P: Sync.width
C: Back porch Q: Back porch
D: Active video R: Active video
E: Front porch S: Front porch
- 13 -
1 640400 @ 70Hz 31.469 70.087 N P 31.778 3.813 1.907 25.422 0.636 14.268 0.064 1.112 12.711 0.381
2 640480 @ 60Hz 31.469 59.940 N N 31.778 3.813 1.907 25.422 0.636 16.683 0.064 1.048 15.253 0.318
3 640480 @ 85Hz 43.269 85.008 N N 23.111 1.556 2.222 17.778 1.556 11.764 0.069 0.578 11.093 0.023
4 800600 @ 85Hz 53.674 85.061 P P 18.631 1.138 2.702 14.222 0.569 11.756 0.056 0.503 11.179 0.019
5 1024768 @ 85Hz 68.677 84.997 P P 14.561 1.016 2.201 10.836 0.508 11.765 0.044 0.524 11.183 0.015
6 12801024 @ 85Hz 91.146 85.024 P P 10.971 1.016 1.422 8.127 0.406 11.761 0.033 0.483 11.235 0.011
7 16001200 @ 85Hz 106.250 85.000 P P 9.412 0.837 1.325 6.972 0.279 11.765 0.028 0.433 11.294 0.009
3. IC APPLICATION
Ref No. Description Application
Deflection circuit
IC301 UPC1888FCT H&V oscillator, Distortion/Size/Phase/DBF control
IC401 LA7840L Vertical deflection output
Power circuit
IC302 LM317T 12V regulator
IC803 M51951BSL 5V power watcher (Microprocessor system reset)
IC901 TEA1504 Main power control
IC903 LM317T 12V regulator
IC904 LM317T 6.3V regulator (Heater voltage ON/OFF control)
IC905 431 Feedback control
IC906 7705 / 2405 5V regulator
Microprocessor circuit
IC801 TMP86PP11AN Microprocessor
IC802 24C08 E2PROM
High voltage circuit
IC502 MSPAD383 High voltage output control
Video circuit
IC201 LM1269 Video pre-amplifier
IC202 LM2467 Video output
IC203 M35047-057SP/063SP On screen display control
IC204 LM2480NA Cut-off control
IC205 7805 5V regulator
CRT correction circuit
IC705 M62393P D/A converter
Sync processing circuit
IC101 BA7078S Video input switch
IC102 24LC21 E2PROM
IC103 24LC21 E2PROM
IC104 74LS157 H-sync and S.O.G. input switch
- 14 -
Microprocessor specifications
Pin Name Function Pin Name Function
1 GND GND 42 V-IN V-SYNC signal input
2 XIN 12MHz X'TAL 41 H-IN H-SYNC signal input
3 XOUT 12MHz X'TAL 40 V-OUT V-SYNC signal output
4 TEST GND 39 H-OUT H-SYNC signal output
5 VDD 5V 38 CLAMP Video clamp signal output
6 CS1 Cushion-S switching signal 1 output 37 MODEL-SW Model no. switching
7 CS2 Cushion-S switching signal 2 output 36 MODEL-SW Model no. switching
8 RESET Reset 35 DDC-SCL DDC Clock
9 CS3 Cushion-S switching signal 3 output 34 DDC-SDA DDC Data
10 CS4 Cushion-S switching signal 4 output 33 ROM-SDA E2PROM data
11 CS5 Cushion-S switching signal 5 output 32 ROM-SCL E2PROM clock
12 CS6 Cushion-S switching signal 6 output 31 I2C-SDA I2C data
13 H-LIN1 H-Linearity switching signal 1 output 30 I2C-SCL I2C colck
14 H-LIN2 H-Linearity switching signal 2 output 29 LED LED control signal output
15 DRIVE H-Drive switching signal output 28 VIDEO-SW Video input terminal select signal output
16 SIG-SEL Video input terminal select signal input 27 PS1 Main power control signal output
17 OPQ O.P.Q. ON/OFF select signal input 26 DEG Degauss control signal output
18 TEMP Surrounding temperature detection 25 PS2 12V power control signal output
19 FUNNEL CRT Funnel temperature detection 24 CLK Automatic adjustment clock
20 KEY Front Menu/+/- key signal input 23 DATA-IN Automatic adjustment data input
21 VREF 5V 22 DATA-OUT Automatic adjustment data output
- 15 -
4. CIRCUIT DESCRIPTION
80V line: Supplied to the HIGH VOLTAGE OUTPUT circuit, the CUT-OFF-IC and the VIDEO
OUTPUT IC as power source.
30V line: Supplied to the HORIZONTAL DEFLECTION OUTPUT (variable B voltage control) and
the HORIZONTAL DRIVE circuits as power source.
15V line: Supplied to each 12V POWER CONTROL and the CRT CORRECTION (+) circuits and VERTICAL
OUTPUT IC (+) as power source.
12V line: Supplied to the CRT CORRECTION circuit () and the VERTICAL OUTPUT IC () as power
source.
D901
T901
AC-IN L910
9 10 80V
+
C909
13 30V
5 + +
15V
Q901 12
3
IC901 15 IN
IC903 OUT
12V
+
2 14
14
1
8
16
IN
IC904 OUT 6.3V
R919
R922
+ CRT HEATER
5
6
17
13
7
18
IN
IC906 OUT
5V
9
+ +
-12V
PC901 VR901
- 16 -
(2) Power management modes
Stand-by / Suspend state
The 12V line of the T901 secondary stops so that a load current decreases and the feedback voltage to
pin 9 of IC901 declines. The output frequency of pin 4 of IC901 is switched to 23kHz from 57kHz and
it reduces a power.
Active-off state
Input voltage to IC906 is supplied from 80V line of T901 secondary when D914 (thyrister) is activated so
that IC901 is switched to burst transmission mode (intermittent oscillation).
Therefore, the output voltages of T901 secondary decline to approx. 7% of normal output voltage and it
reduces a power.
- 17 -
4-2. PROTECTION circuit
This circuit is composed of the following protection circuits to prevent a damage to the monitor and X-ray radiation
when the monitor is inoperative.
When the circuit is in the following cases, pin 19 of IC301 turns to 5V and then the horizontal drive signal output
from pin 17 and the variable B control pulse output from pin 14 turn to LOW level (0V). It makes the HORIZONTAL
DEFLECTION OUTPUT and the HIGH VOLTAGE OUTPUT circuits stop.
The signal that the X-RAY PROTECTION circuit is activated is sent to IC801 (Microprocessor) from IC301 by I2C-
BUS when pin 19 turns to 5V. IC801 receives the signal and then PS1 signal of pin 27 turns to HIGH level (5V) so
that the DC voltages except for the 5V line are turned off.
In case that the PROTECTION circuit is activated and the HORIZONTAL DEFLECTION OUTPUT, HIGH VOLTAGE
OUTPUT and MAIN POWER SUPPLY circuits are turned off, turn OFF and ON the Power Switch to recover.
The PROTECTION circuit operates in the following cases:
+B9 line: The voltage is 320V or more.
X-RAY PROTECTION circuit: The high voltage is 29.9kV or more.
ARC LIMIT circuit: The beam current is 2.5mA or more.
- 18 -
4-4. DISPLAY POWER MANAGEMENT circuits
(1) Stand-by / Suspend state:
When receiving no horizontal or vertical sync signal for 6 seconds, the output voltage of pin 25 of
IC801 turns to 5V from 0V and Q308 and Q903 are turned off. The output voltages of IC302 and IC903
(12Vreg.) turn to 1.2V from 12V and then the circuit controlled by 12V stops operation. There-
fore, it keeps the power consumption 15W or less.
PS1 PS2
Mode Sync signal Circuit
IC801 pin 27 IC801 pin 25
Normal H,V-Sync, VIDEO: ON HIGH LOW All circuits are activated.
Stand-by V-Sync, VIDEO: OFF HIGH HIGH
12V circuit stops.
Suspend H-Sync, VIDEO: OFF HIGH HIGH
Active-off H,V-Sync, VIDEO: OFF LOW HIGH All circuits except for 5V line stop.
(1) SIGNAL SELECT signal: Set VIDEO-IN 1/2 by controlling pin 13 of IC101.
D-SUB input IC801 pin 28
VIDEO-IN 1 LOW
VIDEO-IN 2 HIGH
(2) The input sync signal to IC801 is processed by SYNC SIGNAL PROCESSING circuit in IC801 as follows:
- 19 -
4-6. VIDEO circuit
(1) Pre-amp
<VIDEO>
The video signal from D-SUB connector via IC101 is input to IC201 pre-amplifier and then
clamped by clamp signal input to pin 18. The blanking signal input to pin 17 is synthesized with
the clamped signal and then output from pins 30 (RED), 28 (GREEN) and 26 (BLUE) respec-
tively.
V-BLK signal: Remove the raster retrace line.
H-BLK signal: Remove the side raster rolling.
<ABL>
DC voltage input to pin 31 of IC201 controls the amplitude of the video output signal. Therefore, it
controls the FBT beam current.
ABL is activated (entire white raster): Approx. 3.5VDC at pin 31
ABL is not activated (window): Approx. 4.1VDC at pin 31
I2C-BUS controls D/A converter in IC201 as follows:
Contrast
Sub-brightness
R/G/B drive
OSD contrast
D/A output for the CUT-OFF circuit
- 20 -
4-7. CONTROL circuits
(1) HORIZONTAL / VERTICAL OSCILLATION circuit
The sync signal input to IC301 is phase-sifted and converted to the waveform in IC301. The pulse
synchronized with the horizontal sync signal is output from pin 17 as horizontal drive pulse. The
sawtooth wave synchronized with the vertical sync signal is output from pin 4.
The pulse output from pin 17 generates a frequency locked to the input signal under the
following conditions:
The horizontal sync signal is input to pin 26.
The vertical sync signal is input to pin 27.
The feedback pulse (AFC pulse) of the HORIZONTAL DEFLECTION OUTPUT circuit is input to pin 18.
IC301 is auto-sync system and adjusts the horizontal frequency automatically make the vertical
sync signal input to pin 27 trigger. In case that the AFC pulse is not input, the output pulse from pin 17
is unlocked and the horizontal picture size changes with keeping it small.
IC301 pin 4:
V-sawtooth wave output
- 21 -
(2) HORIZONTAL SIZE and DISTORTION CONTROL circuits
The variable B voltage control pulse synchronized with the horizontal sync signal is output from pin
14 of IC301. The horizontal size control voltage and distortion control parabolic wave output from pin
5 are input to pin 11 and then the output pulse of pin 14 controls the horizontal size and distortion
as follows:
H-size: The output duty of pin 14 is varied by the DC voltage input to pin 11.
Distortion: The parabolic wave (AC component) input to pin 11 is synthesized with the output pulse of
pin 14.
Pin 26:
H-sync signal input
Pin 18:
AFC pulse input
Pin 14:
Variable B control pulse output
Pin 17:
H-DRIVE pulse output
- 22 -
4-8. HORIZONTAL DEFLECTION circuit
The horizontal drive pulse output from pin 17 of IC301 is pre-driven by Q503 and T501 and then supplied to
Q504 (H-OUT) base as a current.
The current is amplified by Q504 and then supplied to the deflection yoke as a deflection current to control the
horizontal deflection.
Center voltage
IC401 pin 2 output waveform
- 23 -
4-10. DYNAMIC BEAM FOCUS (DBF) circuit
(1) H-DBF
The parabolic wave of horizontal period is output from pin 9 of IC301 and then amplified by
Q512 and Q513. It increases up to approx. 500Vp-p by T503 and synthesized with V-
parabolic wave and then added to the focus circuit of the FBT (flyback transformer).
(2) V-DBF
The parabolic wave of vertical period is output from pin 8 of IC301 and then amplified by Q516.
It is synthesized with H-parabolic wave.
- 24 -
4-11. CRT CORRECTION circuit
Following adjustment and functions are for CRT correction.
H/V-CONVERGENCE
TILT-DY
NS-RRC
Landing (TR/TL/BR/BL) * Only for MA201D and i21A.
- 25 -
5. SERVICE PARTS LIST
WARNING !
The components identified by ! in this manual are critical
for safety.
Replace only with part number specified .
FAMILY-TREE
ASSY-PACKING
ASSY-MONITOR
ASSY-PWB-MAIN
ASSY-PWB-VIDEO
SUB-MATERIAL
- 26 -
ELECTRICAL PARTS LIST
Abbreviation Meaning
R-C Resistor-Carbon
R-MB Resistor-Metal
R-FUSE Resistor-Fuse
C-C Capacitor-Ceramic
C-E Capacitor-Electrolytic
C-PP Capacitor-Polypropylene
C-MF Capacitor-Multilayer Metallized Polyester Film
D Diode
ZD Zener Diode
TR Transistor
PHC Photo Coupler
PTH Positive Thermistor
HDT Horizontal Drive Transformer
FBT Flyback Transformer
VR Variable Resistor
SW Switch
SWT Switching Transformer
F 1% H 3%
J 5% J 5%
K 10% K 10%
M 20%
P +100%
0%
Z + 80%
20%
- 27 -
6. EXPLODED VIEW Note: The numbers in this exploded view are the same as the reference numbers in the Chapter 5.
16 18 19 20 53 54 55
58
45
27
35 36
43
38
40 22 23
48 47
L=702
49
39
47
31 33
Bottom face
- 50 -
Torque
6-8kgf-cm 83 6 32
35
Note: Except where indicate otherwise, all screw torcue is 9-11kgf-cm in ASSY-MONITOR.
32
ASSY-1 ASSY-2
61
62 33
34
590R167-01
CRT Side 33
Torque
27-28kgf-cm
79 4
ANODE BUTTON ANODE CAP 16
Insert 71
Top Side 32
AL
40mm 73
590R168-01
10mm
m
n 43
m
70
-1
0 2-3mm
16 75
Note)
65 4 63
: Dangerous Voltage Symbol 63
20
30
CT
70 8 75 Upper: 22=4
65
49 92 DG
Lower: 22=4 85 6
L=402
48 NS
70 3 CLT
CLB
44 45
46
Short
75 DG
Long
47
71 2
61
- 51 -
ASSY-3
NS-COIL
Torque
42 WIRING
3-5kgf-cm
84 80
81 PWB-SW 4 a
MA203DT A To CORNER-COIL
Torque
To DG-COIL PWB-CONT
42
ASSY-PWB-MAIN 87
To EARTH
B TO THERMISTOR
14 -WIRE A
TO EARTH-WIRE
PWB-SW
80 CLT A
Torque CT PWB-MAIN
CLB
M12
82 2
84 75
R724
Torque 91 D
6-8kgf-cm H F
80 2
0
4
C320
c
72
To DY
d
74 2 75
DY-LEAD
g To ANODE
e
b DY
75
TO CV(DY)
B
36 MC
h
E f
BLACK SC
75
FBT
39 DG
j
RED
80
25 a CLT,CLB,NS
41
k
b B,DG D G
c H,D,F
l m
d H,D,F PWB-SW
e H,D,F,NS
H
F
NS TILT1 E
f H,D,F,NS,E
Red CV
g TILT,DY
G1 SC
h ANODE-LEAD Black
PWB-CONT j H,D,F,NS,E,TILT
k SC,FOCUS(R),FOCUS(B) 53
82 2 l 52
E,F,G,NS,SC,H,CV,TILT PWB-VIDEO
Torque m FOCUS(R),FOCUS(B)
6-8kgf-cm
n ANODE-LEAD
- 52 -
ASSY-5
ASSY-4
28
29
Torque
12-13kgf-cm
85 4
80 4
26
27
B A
86 2
21 23
D G
E F
42
42
80
- 53 -
Note: Except where indicated otherwise, all screw torque is 3-5kgf-cm in ASSY-PWB-MAIN.
C534 Q530,Q531
Q532,Q533
41 2 Q504 Q521,Q901 D503,D529 Q534,Q307 Q514,Q515
C534 45
23 40
m
Torque
0.5
0.5
0.5
0.5
0.5
0.5
R538
m
9-11kgf-cm
1
~
7
3.5
2.5
4.5
2.3
33 +
2.5
4.9
27.4
C534
0.5
9~10mm
1.0
M11 13
57 L=15mm
4
Torque
15
6.5
6-8kgf-cm
50
30 2
-
Torque C534 12.5 0.5 5 0.8 7.5 0.5 5 0.8 3 0.8
9-11kgf-cm
29
11
12
22 AH
23 32
2
43
33 2
Torque AH
32
9-11kgf-cm 21 CN901 16
MC
Q521 AH
DY 53
26 E
33 2
RED 32
36
BLUE
Torque
9-11kgf-cm Q901
M11 19 YELLOW
BROWN
M12 32
Note)
F
Q504
18 : Protective Earth (Ground) Symbol
31 D503
34
17 20 32
2 D529 31 IC401
D
A Note) 53
H
18 1
C533,C540,C544
C540
C544
32 AH
Torque
T504 9-11kgf-cm
(FBT) C533 IC903,IC904
D907, D911 14
D901 33
FRONT 1
4
6
IC301
AH
45
32
33
m
45 45
m
C326 2
m
R301
AH Q531,Q532,
3
m
2
~
~
3
Torque
2
Q533,Q534
6~7mm
m
AH
2
m
9-11kgf-cm
6~7mm
6~7mm
C338
C533 24
28 C544 C540
28
AA 28
5mm
4mm
R411 C316
D911 D907 32
AB
IC301 23-16pin 15
AA
4
3
L=15mm
AB
R971 AH
J81 55 R971 Q514 25 CN901
R929
C960
10mm
IC301
C402
L=40mm 8 1
s
1
27 C936 R333
5.5mm
6
TC01 2 Q307
L=20mm
55
6
AA 33 AH
R333 31
4.5
AB Torque
9-11kgf-cm
AA
1
Q515 AH
AB 4.5 5.5mm 24 mm
10
- 54 -
12
MA203DT
Note: Except where indicated otherwise, all screw torque is 3-5kgf-cm in ASSY-PWB-VIDEO.
PWB-VIDEO
AH
18
24
IC202 16
MA203DT
15 PWB-CONT
VN
PWB-SW V2
VA
IC205 G
24 AH
Torque
9-11kgf-cm
11
- 55 -
12
16
PWB-SW
- 56 -
7. DIAGRAMS
(MA203DT)
- 57 -
(MA203DT A)
- 58 -