Escolar Documentos
Profissional Documentos
Cultura Documentos
INKJET PRINTER(MFP)
SCX-1100
SERVICE Manual
1. Precautions
2. Specifications
4. Troubleshooting
6. Block Diagram
7. Connection Diagram
ELECTRONICS
This service manual is also provided on the web, Samsung Electronics Co.,Ltd. March 2001
the ITSELF system Samsung Electronics Co., Ltd. Printed in Korea.
http://itself.sec.samsung.co.kr VERSION NO. : 1.02 CODE : JB-0023A
- This Service Manual is a property of Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law. -
This manual is stated and
provided for service description.
All rights reserved. Any parts of the
information in this manual are prohibited
from free duplication, use or translation
without prior written approval except in
cases allowed by the Copyright Act.
Specifications are subject to change without
prior notice.
Please read the following carefully to prevent any accidents and not to damage the unit during service.
Very careful precautions should be taken when replacing 7. When disassembling, assembling, also observe small
parts. Before replacing, please check cables because you components are located in place.
cannot put the cables that you removed for replacing parts 8. If you uncover and turn the machine over to replace some
into the proper place if you would not make sure of where parts, toner or paper particles may contaminate the LSU
they were connected and in which condition. window. Protect the LSU window with clean paper.
1. Pull out paper cassette, printer cartridge installed. Releasing Plastic Latches
Especially careful not to be scratched by the surface of
developer or not to expose them to light. Many of parts are held in
2. Turn the power switch off. place with plastic latches.
3. Take out the power plug, printer cable from the printer. The latches break easily :
release them carefully.
4. Use only the same type of part as original when replacing To remove such parts, press
parts. the hook end of the latch
5. Do not force to open or fasten plastic material compo- away from the part to which
nents. it is latched.
6. Be careful that small parts such as screws should not get
in the printer.
Certain semiconductor devices can be easily damaged by 4. Use only an anti-static solder removal device. Some sol-
static electricity. Such components are commonly called der removal devices not classified as anti-static can
Electrostatically Sensitive (ES) Devices, or ESDs. generate electrical charges sufficient to damage ESDs.
Examples of typical ESDs are: integrated circuits, some field
effect transistors, and semiconductor chip components. 5. Do not use Freon-propelled chemicals. When sprayed,
The techniques outlined below should be followed to help these can generate electrical charges sufficient to dam-
reduce the incidence of component damage caused by sta- age ESDs.
tic electricity.
6. Do not remove a replacement ESD from its protective
CAUTION: packaging until immediately before installing it. Most
Be sure no power is applied to the chassis or cir- replacement ESDs are packaged with all leads shorted
cuit, and observe all other safety precautions. together by conductive foam, aluminum foil, or a compa-
rable conductive material.
2. After removing an electrical assembly equipped with 9. Minimize bodily motions when handling unpackaged
ESDs, place the assembly on a conductive surface, such replacement ESDs. Normal motions, such as the brush-
as aluminum or copper foil, or conductive foam, to pre- ing together of clothing fabric and lifting ones foot from a
vent electrostatic charge buildup in the vicinity of the carpeted floor, can generate static electricity sufficient to
assembly. damage an ESD.
5 Cotton Swab
Standard : For general home use, for medical ser-
vice.
2 Electronic Scale
Standard: Equipment to check the weight of con-
sumables supplied by Samsung Electronics.
(The gram unit can be measured.)
3 Driver
Standard: "-" type, "+" type (M3 long, M3 short, 7 Software(Driver) installation CD ROM
M2 long, M2 short).
Note:
(2) Speed claims based on the test files: spdtstc.sam(mono), spdtstc2.sam(color)/Letter size
(3) Non-standard cable can cause misoperations.
Ink Yield about 1075 sheets (5% Pattern, A4) about 275 sheets (15% Pattern, A4)
2-3 Copier
Note:
(1) Speed claims based on the test chart : Printed spdtstc.sam(mono), Printed spdtstc2.sam(color)/Letter size
2-4 Scanner
DC Channels (4)
(2 Channels) +3.3V +5%, +30V +10%
External Power On/Off Key Power Down Key (It does not cut the primary power input off)
Note:
(4) No load condition.
2-6 Dimension
When you disassemble and reassemble components, you Whenever servicing the machine, you must perform as fol-
must use extreme caution. lows:
The close proximity of cables to moving parts makes proper 1. Check to verify that documents are not stored in memory.
routing a must. If components are removed or replaced, any 2. Unplug the power cord.
cables disturbed by the procedure must be replaced as close
3. Use a flat and clean surface.
as possible to their original positions.
4. Replace only with authorized components.
Before removing any component from the machine, note the 5. Do not force to remove or planten plastic-material compo-
cable routing that will be affected. nents.
6. Make sure all components are in their proper position.
1. Remove two screws securing the rear cover. 3. Remove two screws securing the main cover.
2. Open the front door from the main cover. 4. Pull the scanner ass'y upward then, unplug the two
connectors and CCD cable.
5. Pull the platen cover upward and remove it. 8. Remove two screws securing the scan upper and
remove it.
6. Pull the OPE cover upward and remove it. 9. Unlatch the scan lawer securing the scan upper and
remove it.
7. Remove five screws securing the OPE upper and 10. Remove the two screws securing the scan upper.
unplug the one connector from the OPE panel.
11. Unlatch the scan dummy and take out the glass 14. Pull up the CCD shaft and take out the scanner
from the scan upper. module.
12. Remove the CCD cabl. 15. Remove two screws and take out the motor bracket.
13. Push the belt holder and take out the belt, as 16. Remove two screws securing the scan motor and
shown below. remove it.
1. Before you remove the ope unit, you should remove: 4. Remove two screws securing the OPE upper to the
Scanner Ass'y (see page 3-1) LCD board.
1. Before you remove the rear cover, you should 4. Remove the rear cover, as shown below.
remove:
Scanner Ass'y (see page 3-1)
3-5 SMPS
1. Before you remove the SMPS, you should remove: 3. Pushing down the hooks on both ends, pullout the
Scanner Ass'y (see page 3-1) SMPS.
Rear Cover (see page 3-5)
1. Before you remove the engine ass'y you should 3. Remove the three screws securing the engine ass'y
remove: and remove it.
Scanner Ass'y (see page 3-1)
Rear Cover (see page 3-5)
1. Before you remove the asf feeder, you should 3. Remove three screws securing the ASF feeder to the
remove: main cover.
Scanner Ass'y (see page 3-1) Take out the ASF feeder.
Rear Cover (see page 3-5)
SMPS (see page 3-6)
1. Before you remove the cartridge ass'y you should 4. Take out the emcoder strip, as shown below.
remove:
Scanner Ass'y (see page 3-1)
Rear Cover (see page 3-5)
Engine Ass'y (see page 3-6)
ASF Feeder (see page 3-7)
5. Push the holder pulley to the right and take out the
belt.
1. Before you remove the carrier motor, you should 3. Remove two screws securing the carrier motor and
remove: take out the motor from the main frame.
Scanner Ass'y (see page 3-1)
Rear Cover (see page 3-5)
Engine Ass'y (see page 3-6)
ASF Feeder (see page 3-7)
Cartridge Ass'y (see page 3-8)
1. Before you remove the main PBA, you should 4. Pull the sensor lever backward and take out the main
remove: PBA, as shown below.
Scanner Ass'y (see page 3-1)
Rear Cover (see page 3-5)
Engine Ass'y (see page 3-6)
ASF Feeder (see page 3-7)
Cartridge Ass'y (see page 3-8)
1. Before you remove the holder roller, you should 3. Pull the holder downward and take it out from the
remove: main frame.
Scanner Ass'y (see page 3-1)
Rear Cover (see page 3-5)
Engine Ass'y (see page 3-6)
ASF Feeder (see page 3-7)
Cartridge Ass'y (see page 3-8)
Main PBA (see page 3-10)
1. Before you remove the home ass'y you should 3. Unlatch the home ass'y by pushing the parts hooked
remove: to the main frame using a sharp tool. Take out the
Scanner Ass'y (see page 3-1) home ass'y from the main frame.
Rear Cover (see page 3-5)
Engine Ass'y (see page 3-6)
ASF Feeder (see page 3-7)
1. Before you remove the base frame, you should 4. Remove the exit roller from the main frame and take
remove: out the exit belt.
Scanner Ass'y (see page 3-1)
Rear Cover (see page 3-5)
Engine Ass'y (see page 3-6)
ASF Feeder (see page 3-7)
Cartridge Ass'y (see page 3-8)
Main PBA (see page 3-10)
Hold Roller (see page 3-11)
Home Ass'y (see page 3-11)
2. Remove the four springs and take out the four roller
frictions, as shown below.
1. Before you remove the feed roller, you should 2. Turn the bearing feed counterclockwise and take out
remove: the base frame and feed roller from the main frame.
Scanner Ass'y (see page 3-1)
Rear Cover (see page 3-5)
Engine Ass'y (see page 3-6)
ASF Feeder (see page 3-7)
Cartridge Ass'y (see page 3-8)
Main PBA (see page 3-10)
Hold Roller (see page 3-11)
Home Ass'y (see page 3-11)
Base Frame (see page 3-12)
1. Before you remove the LF bracket ass'y, you should 2. Remove two screws and take out the LF bracket
remove: ass'y from the main frame.
Scanner Ass'y (see page 3-1)
Rear Cover (see page 3-5)
Engine Ass'y (see page 3-6)
ASF Feeder (see page 3-7)
Cartridge Ass'y (see page 3-8)
Main PBA (see page 3-10)
Hold Roller (see page 3-11)
Home Ass'y (see page 3-11)
Base Frame (see page 3-12)
Feed Roller (see page 3-13)
To enter the service mode, press ENTER, LEFT, RIGHT, LEFT, SETUP in sequence, and the LCD displays T , the machine
has entered service (Tech) mode.
To return to normal user mode, press ENTER, LEFT, RIGHT, LEFT, SETUP in sequence again, or turn the power off, then
on by unplugging and plugging the power cord.
Because the explanation of the User Mode items is already mentioned at the User guide in detail, It will not be described at
Service manual.
Initiating this function will put the system into the factory
shipping state. The procedure is as follows :
1. Unplug power
2. Press and hold " SETUP" button
3. Plug power in
4. Continue holding " SETUP" button until CLEARING
MEMORY message appears on LCD
5. Unplug power
Samsung Electronics 4-3
Troubleshooting
4-3. Troubleshooting
The solutions of troubleshooting in this 'Service Manual' explain the expected causes and
how to check according to each problem and describe how to replace the defected parts (unit
of ASS'Y) if necessary.
The contents of this 'Service Manual' describe general ones only among many kinds of prob-
lems and causes while using the Product.
The contents of this 'Service Manual' describe mainly technical explanations of the Product
H/W and parts on the assumption that there is no problem in S/W.
2. Check if the resolution is set too low in PC Scan 2. If the resolution is set to low, let the user be acquainted
options. (Refer to User's Manual.) with the using method well.
Description Strange characters are displayed on the OPE Panel and buttons are not operated.
Location 1.OPE ASS'Y 2.Connection between the Main B'D and OPE ASS'Y 3.Main B'D.
2. Check if OPE HARNESS is connected to the Main 2. After confirming that OPE HARNESS is connected to
Board correctly. the Main Board correctly, if it is so, then replace the
OPE ASS'Y and Main Board in sequence.
4-3-4 No Power
Description While the power S/W is turned on, it does not work at all.
Location 1.Power code 2.Connection between the Main B'D and Power HARNESS
3.Power ASS'Y 4.Main B'D. 5.OPE Assy
2. Check if DC +3.3V and +30V is supplied to POWER 2. If all the connections are correct, try to replace the
ASS'Y from MAIN B'd. power ASS'Y and the Main B/D in sequence.
( +3.3V and +30V is supplied to POWER ASS'Y from
MAIN B'd)
2. Confirm to catch a click sound, while a key on the 2. Even after the key or harness has been replaced, it is
OPE panel is pressed on. still wrong, try to replace the OPE ASS'Y and the Main
B'D in sequence.
2. Check if a specific key is pressed by another equip- 2. Even after the key has been replaced, it is still wrong,
ment. try to replace the OPE ASS'Y and the Main B'D in
sequence.
Description The paper is jammed inside the set and not exited from.
4-3-10 Multi-Feeding
2. Check if the recording paper is preprinted or crum- 2. Even after the papers are loaded correctly, if multiple
pled. sheets of paper are still fed at once, then try to replace
the ASF ASS'Y.
2. Check if the cartridge box is operated normally. 2. In case the cartridge box is not moved from side to side,
check the Flat Cable connection between the Main PBA
& Frame Home Unit, and even after being connected
properly, if it is still not improved, then try to replace the
cartridge ASS'Y.
3. Check if there is an alien matter in the Dimple contact
point of HEAD of CARTRIDGE BOX
Description The recording papers are put in already, but it cannot be sensed.
Notes:
The SCX-1100 Product has no paper sensor, instead it
displays ERROR when it cannot pick up the paper.
2. Perform the CCD test in the service mode. 2. In case the output waveform is abnormal in the CCD
(Refer to 4-1-3) test, replace the CCD ASS'Y, while replace the Main
B'D in normal.
2. Perform a CCD Test to check if the waveform is nor- 2. If the CCD waveform is abnormal, replace the CCD
mal. (Refer to 4-1-3.) ASS'Y.
3. Clean the cartridge nozzle. 3. Clean the nozzle and confirm again.
2. Check the waveform by performing a CCD test. 2. In case the CCD waveform is normal but the print quali-
(Refer to 4-1-3) ty is bad, try to replace the Main B'D.
2. Test and check the cartridge arrangement. 2. In case the CCD waveform is abnormal, try to replace
(Refer to 4-2) the CCD ASS'Y.
3. Clean the cartridge nozzle. 3. Even after cleaning the outlet of nozzle, the received
(Refer to 4-2) data image is still bad, then replace the cartridge.
Location Cartridge
Description The color is different from the original document in the printing.
2. Check the waveform by performing a CCD test. 2. After having performed a CCD shading test, if it is not
(Refer to 4-1-3) still improved, then try to replace the CCD ASS'Y.
Description While the power is turned on, the printer is not working at all by the PRINT command from the com-
puter.
Description Even after the Print command, there is no response at all or the printing speed is low.
Description The printing is not working properly even when the cable has no problem.
(even after the cable is replaced)
If the printer won't work at all or strange characters are only printed,
it may be the printer driver problem.
pool (Simultaneous Peripheral Operations Online) refers to process the document to be read and
Description stored in the hard disk or the mass storage media, and then to be printed at more convenient time.
While the printer is outputting other file, the file requested to output is undergone to be spooled in the
hard disk, the spool error may occur if a problem occurs in this process.
First, delete the Spool Data if the Spool Error occurs.
Deal drawings and service parts are declared for the items with higher rate
of inferiority and replaceable in the level of service description only.
If inferiority occurs, you can replace the parts by the unit declared in deal
drawings and service items.
Part code and Description is quoted and controlled by determined standard. Refer to this determined
standard, it will help with ordering Part.
ex ) 2007-007961 R-CHIP
Type 1 : Controlled by Company : It can be commonly used for all kinds of product SEC produce.
Mostly, electronics Parts.
Type 2 : Controlled by Division : It is used or one produce. Mostly, Mostly, mechanical Parts.
Assy part and A/S privately used Part is distinguished by part Code and Description.
The are inscription type 2. It is recognized by Part character and front side of description.
1-2
1-1
1 3
S7
4
S7
7-2
5
8
S6
12 S6
13
S6 S3
11
6
S6 7-1
10
S6 7
S8 7 5
2 4
3-2
3-3 3
3-1
1-3
1-3
0 1-2
1-1
2-4-3
2-5
2-4-2
2-4-1
S6
2
2-4
3
3-10
2-2
3-12
3-8-1 3-11
2-1
3-8-7
3-3 S3
3-8-3 3-8-5
2-1
S6 3-8-4
S7 S3
S6 3-15
3-8-6
3-13
3-2
2-3
3-14 3-5
3-1
3-8-2 3-4
3-7
3-8
3-6
3-9
S6
1 19
0
S6
6
7
9 10
16
17 11
13
12 14 15
18
5
S3 4
S5
S7
S7
3-4
3-5
11-1
11-2
15
S7
1-9
1-13
1-3
1-4
1-5
1-1
1-14 1-10
1-7
1-16
1-8
1-15
1-11
1-12
1-2
2-2
S4 2 1
2-5
2-1
2-3
2-6
2-4
5-7 Screw
Samsung Electronics
USB CONN
PC
1284 CONN
COLOR
( AU1)
6. Block Diagram
(15) OPE
CARTRIDGE BUZZER
Main
MONO Controller
CARTRIDGE (U1) ARM7TDM LCD
Main Clock
HEAD 10MHz
MEM CNTR
PRINT HEAD(2PEN) Driver Mcro Controller (U1)
60DPI DOUBLE HEIGHT IC Head Control I/F
(U13)
(U5) SCAN CNTR
ENCORDER RESET
SENSOR DERASTERIZER
CONTROLLER
UART 3 KEY PANNEL
PAPER EXIT
ENCODER SENSOR IEEE 1284
(U7)
TIMERS FLASH ROM
CARRIER
(U4) I/O PORT
MOTOR
Motor INT. CNTR SDRAM
Driver 1M* 16bit
LINE FEED & Regul at or USEB (U9)
MOTOR DM 2 SCANNER
(U16)
48MHz /REQ /ACK ADC CCD Module
+5V 16bit ( COLOR 600DPI )
POWER +12V
+30V (U21) SCAN MOTOR
SMPS Image SCAN STEPPER ( Bi-POLAR STEP )
(30V, 3.3V)
+3.3V Processor MOTOR DRIVER
(U27) OA-980 ( U 10 ,U 1 4 )
AC SDRAM
(4M 16bit)
(110~240V)
6-1
7. Connection Diagram
R8
5.1K
CN1-26 30V
CN1-25 CHY PULLUP
CN1-24 CHX C205
CN1-23 100nF
CN1-22 3.3V
CN1-21 _SF_POR 5V 5VA R155
CN1-20 ACLK C50 1.5K
CN1-19 AGATE
CN1-18 LDCS C66 C67 C49 330uF
R43 BD6 0,5% DGND R153 10K
CN1-17 LATCHCTL 100nF 100uF 100nF 10K 50V R154 USB20-4W2100
CN1-16 PCLK CN11-1 16V 10K BD13
CN1-15 CN11-2 C119 C118 CN8-1
100nF 100uF R144 BD11
CN1-14 PDATA3 CN11-3 BD12 CN8-2
CN1-13 PDATA2 CN11-4 16V R152 CN8-3
L11 0 BD10
CN1-12 PDATA1 BD7 0,5% CN8-4
CN1-11 PDATA0 L5 C204 C203 C209 L9
CN1-10 PLOAD 22pF 22pF 100nF
CN1-9 PENABLE L6 0 GND30
CN1-8 PH_ID1 AGND
CN1-7 PH_ID2 DGND
L12 0 L10
CN1-6 OK2PRT 0
CN1-5
CN1-4 C1 C7
CN1-3 220pF 220pF DGND FGND
CN1-2
CN1-1
5V
30V 5V 5V
GND12 GND30 DGND (UNUSED)
Q9
5V KSA1182-Y
R384
R147 10K
R148 10K
R149 10K
R207 10K
CN7-1 1.5K
1 DIN15
R380 180K
5V 2 KEYTONE Q10 CN16-1
3 OPE_TXDD CN16-2
4 2SC2812L6-TA
_OPE_RES CN16-3
5 OPE_RXD R383
68K CN16-4
CN16-5
_STB CN16-6 ADF_PHA
CN14-1 CD(0:7) OPE_MAGIC ADF_IA0
CN16-7
CN14-2 CN16-8 ADF_IA1
CN14-3 C97 C80 C81 C82 CN16-9 ADF_PHB
CN14-4 100nF 100pF 100pF 100pF CN16-10 ADF_IB0
CN14-5 CN16-11 ADF_IB1
CN14-6 DGND _ADF_DET
CN16-12
CN14-7 CN16-13 _D_DET
CN14-8 DGND CN16-14 _D_SCAN
CN14-9 DGND (UNUSED) REG1_SEN
CN16-15
CN14-10 _ACK
CN14-11 BUSY
CN14-12 PE
CN14-13 SLCT DGND DGND L7 0
CN14-14 _AUTOFD
CN14-15 R209 L8 0
0 5V
CN14-16
CN14-17 C336 DGNDFGND
CN14-18 100pF
CN14-19 5V DGND
R138 47K
R136 47K
C208 11.75VA GND30
CN14-20
CN14-21 100nF
CN14-22
CN14-23 DGND
CN14-24 CN9-1
CN14-25 3711-002815 3.3V
CN14-26
CN14-27 1 MODEM_RX
CN14-28 DGND 2
CN14-29 3 MODEM_TX1 R146 SPK_OUT+ CN13-1
CN14-30 4 MODEM_TX2 4.7K CN13-2
CN14-31 _INIT 5 SPK_OUT-
CN14-32 _ERROR 6 REMOTE
CN14-33 7
8 R137 1K
CN14-34 _HOOK_OFF R145 100
CN14-35 9 _RING_DET CN12-1 COVER_OPEN
CN14-36 _SLCTIN 10 R135 1K CN12-2
C338 11 DP CN12-3
C337 12
100pF C197 CN3-1
100pF 13 RECALL CR_NA
100nF CN3-2
14 CN3-3
DGND CR_A
R125 5045-03A
LIU C182 C181 Q5 3 3K
DGND DGND 100nF 100pF 2SC2812L6-TA 1TP230 3711-000198|scon_pin3_2.5mm
_CML_ON
2
C194 C R126 DGND
100pF 2K
(UNUSED) B E
47pF
47pF
1 Q1
CN5-3 LAMP_ON 2SC2812L6-TA
CN5-2 1K 2
CN5-1 R373
4.7K
C32
C35
C38
C39
FPC_24
CD74HCT244M
CCD DGND
AGND GND12 DGND
DGND DGND
DGND DGND
DGND DGND
SCX-1100
CONTENTS
1. Block Diagram
2. Connection Diagram
3. Circuit Description
4. Schematic Diagrams
MAIN
PC
USB CONN
1
Samsung Electronics
1284 CONN
COLOR
(15) ( AU1)
CARTRIDGE OPE
1. Block Diagram
Main BUZZER
MONO Controller
CARTRIDGE (U1) ARM7TDM LCD
Main Clock
HEAD 10MHz
MEM CNTR
PRINT HEAD(2PEN) Driver Mcro Controller (U1)
60DPI DOUBLE HEIGHT IC Head Control I/F
(U13)
(U5) SCAN CNTR
ENCORDER RESET
SENSOR DERASTERIZER
CONTROLLER
UART 3 KEY PANNEL
PAPER EXIT
ENCODER SENSOR IEEE 1284
(U7)
TIMERS FLASH ROM
CARRIER
(U4) I/O PORT
MOTOR
Motor INT. CNTR SDRAM
Driver 1M* 16bit
LINE FEED & Regul at or USEB (U9)
MOTOR DM 2 SCANNER
(U16)
Repair Manual
BLOCK DIAGRAM
1-1
2
CONNECTION DIAGRAM
2. Connection Diagram
Repair Manual
2-1
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3
CIRCUIT DESCRIPTION
3. Circuit Description
MAIN PBA
Repair Manual
3-1
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
3-3.DETAILED DESCRIPTION
3. D0 ~ D15
- 16BIT DATA BUS
4. A0 ~ A24
- ADDRESS BUS (A23 ~ A24 RESERVED)
Repair Manual
3-2
Samsung Electronics
- This Document can not be used without Samsung's authorization -
MAIN
Samsung Electronics
USB CONN
PC
1284 CONN
COLOR
(15) ( AU1)
CARTRIDGE OPE
Main BUZZER
MONO Controller
CARTRIDGE (U1) ARM7TDM LCD
Main Clock
HEAD 10MHz
MEM CNTR
PRINT HEAD(2PEN) Driver Mcro Controller (U1)
60DPI DOUBLE HEIGHT IC Head Control I/F
(U13)
(U5) SCAN CNTR
ENCORDER RESET
SENSOR DERASTERIZER
CONTROLLER
UART 3 KEY PANNEL
PAPER EXIT
ENCODER SENSOR IEEE 1284
(U7)
TIMERS FLASH ROM
CARRIER
(U4) I/O PORT
MOTOR
Motor INT. CNTR SDRAM
Driver 1M* 16bit
LINE FEED & Regul at or USEB (U9)
MOTOR DM 2 SCANNER
Repair Manual
CIRCUIT DESCRIPTION
3-3
CIRCUIT DESCRIPTION
EXTCLK
tRAD tRAD
ADDR
tRCD tRCD
nGCSx
Tacs
Tcah
tRWD
tRWD
nWE
nBEx 1
tRDD
DATA
tRDH
EXTCLK
tRAD tRAD
ADDR
tRCD tRCD
nGCSx
Tacs
Tcah
tRWD
tRWD
nWE
nBEx
Tcos
Toch
tRDD
tRDD
DATA
Repair Manual
3-4
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
SCLK
SCKE 1
tSAD
ADDR/BA
tSAD
AP/A10
tSCSD
nGCSx
tSRD
nSRAS
Trp Trcd tSCD
nSCAS
tSBED
nBEx
tSWD Tcl
nWE
tSDS
DATA
tSDH
Repair Manual
3-5
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
SCLK
SCKE 1
tSAD
ADDR/BA
tSAD
AP/A10
tSCSD
nGCSx
tSRD
nSRAS
Trp Trcd
nSCAS tSCD
tSBED
nBEx
tSWD
nWE
tSDD
DATA
tSDD
Repair Manual
3-6
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
SCLK
SCKE 1
tSAD tSAD
ADDR/BA
tSAD
AP/A10
tSCSD tSCSD
nGCSx
tSRD tSRD
nSRAS
Trp Trc
tSCD
nSCAS
nBEx 1
tSWD
nWE
DATA
HZ
Repair Manual
3-7
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
SCLK
SCKE 1
tSAD tSAD
ADDR/BA
tSAD
AP/A10
tSCSD tSCSD
nGCSx
tSRD tSRD
nSRAS
Trp Trc
tSCD
nSCAS
nBEx 1
tSWD
nWE
DATA
HZ
Repair Manual
3-8
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
SCLK
tCKED tCKED
SCKE
tSAD tSAD
ADDR/BA
tSAD
AP/A10
tSCSD tSCSD
nGCSx 1
tSRD tSRD
nSRAS 1 1
Trc
Trp
tSCD
nSCAS 1
nBEx 1 1
tSWD
nWE 1
DATA
HZ HZ
Repair Manual
3-9
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
Repair Manual
3-10
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
Repair Manual
3-11
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
BYTE 0 BYTE 1
1. The host places data on the data lines and indicates a data cycle by setting nAUTOFD.
2. Host asserts nSTROBE low to indicate valid data.
3. Peripheral acknowledges host by setting BUSY high.
4. Host sets nSTROBE high. This is the edge that should be used to clock the data into the Peripheral.
5. Peripheral sets BUSY low to indicate that it is ready for the next BYTES.
6. The cycle repeats, but this time it is a command cycle because nAUTOFD is low.
Repair Manual
3-12
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
BYTE 0 BYTE 1
Repair Manual
3-13
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
Repair Manual
3-14
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
Pn
- PDATA0 == BLKHTR> High : Turn on Substrate
Heater of Mono Head.
<Figure 11 HEAD Control Part Timing Diagram>
- PDATA1 == COLHTR> High : Turn on Substrate
2. A-LINE driving circuit Heater of Color Head.
13 Address Lines are input into 13 Address Counters in - PDATA2 == nHSM> Low : Enable Select Signal of
sequence at Rising edge of ACLK signal, which is input Mono Head.
serially into Spitfire. Output of this Counter was connected - PDATA3 == nHSC> Low : Enable Select Signal of
to each A-line driver, and this driver output becomes A-line Color Head.
signal. The sequence of signal input into Address Counter
is decided by ADIR, and if it is ADIR=0, it is input in
sequence of A13A1, and if it is ADIR=1, in sequence of A1 When Substrate Heater is turned on, Over-current Check
=> A13. AGATE signal is used to reset Address Counter. If circuit is operated, automatically, and,if the current is above
it becomes AGATE=1, A-Line output becomes Low state. 750mA, the printer stops operation after OK2PRT
The cycle of ACLK is 1.5 in minimum, and Sink current of becomes low.
each Driver is 60mA.
Repair Manual
3-15
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
Tcs-sclk
Tcs-sclk
/ TBCS
TBCLK
Tdsu Tdhd
SDI stays at
TBDO bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 bit 8 bit 9 bit 10 bit 11 bit 12 bit 13 last value
LSB MSB
time
Repair Manual
3-16
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
DESCRIPTION
PORT NAME PIN NO I/O SIGNAL NAME
H L
nGCS0 136 O nROM_CS FLASH MEMORY CHIP SELECT
nGCS1/GOP16 137 O nIP_CS OA-980 CHIP SELECT
nGCS2/GOP17 138 O reserved -
nGCS3/GOP18 139 O reserved -
nGCS4/GOP19 141 O reserved -
nGCS5/GOP15/PDE 142 O 245DIR P1284 DIRECTION CONTROL
nGCS6:nRAS0:nSCS0 34 O reserved -
/GOP13
nGCS7:nRAS1:nSCS1 35 O nSCS1 SDRAM1(16Mb) CHIP SELECT
/GOP14
Repair Manual
3-17
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
3. J3 Assigned GPO
Repair Manual
3-18
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
This system is configured with PRIMARY RESET(/POR) of 3-3-3-1 POWER MONITOR ( U13 )
Power Reset, Reset by WATCH DOG TIMER, external Since +3.3V power supplied to XC61FN3112MR is unsta-
PRIMARY RESET, and SECOND RESET(/_F_POR) ble, when it becomes 3.1V(3.038V~3.162V), it is checked
which was done AND. PRIMARY RESET SYSTEM is used as the POWER FAILURE. And the output terminal of
for resetting MAIN CONTROLLER(U15) when System XC61FN3112MRF becomes LOW(0V),it is applied to
Power is authorized, and SECOND RESET resets FLASH S3C46MOX(Jupiter3)(U15), and RESET(LOW ACTIVE) is
MEMORY(U7). Figure 15 below is BLOCK DIAGRAM operated When S3C46MOX(Jupiter3) Reset is cancelled,
related to the reset of entire system. FLASH MEMORY connected to /F_POR of
When +3.3V reaches 3.1V so that system may operate, S3C46MOX(Jupiter3) is Reset together. Output terminal of
POWER MONITOR(U13) moves to High(+3.3V) after XC61FN3112MRF is pulled up 100K in the structure of
maintaining low(OV) in the degree of 50mS-200mS output Open drain.
while monitoring it. This Reset signal is input into MFP
CONTROLLER(S3C46MOX(Jupiter3 : U15) right away,
and MFP CONTROLLER becomes awake. And it releases 3-3-3-2 WATCH DOG OUTPUT (/F_POR)
/F_POR after MCLK 1 clock.
Since WATCH DOG TIMER, which is Programmable
Counter in S3C46MOX(Jupiter3) is set as disable for INI-
TIAL STATE, it shall be set as Disable so that it wont oper-
ate, and after it is initialized for operation, it shall be reused
by setting it Enable. When Watch Dog Reset occurs, it is
about 10mS depending on the value set at the initial stage.
And Counter value of Watch Dog Timer is changed by the
program. Reset signal (/F_POR,UI5-106) shall be generat-
ed, and entire system shall be Reset and initialized.
Repair Manual
3-19
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
MEMORY applied in this system are FLASH MEMORY(U7) Image processing Section
of 1MB, SDRAM(U9) of 2MB. : Full quality RGB to CMYK or 6 color conversion
Photo/Text detect allows mixed documents.
3-4-2 MEMORY CONFIGURATION Arbitrary image scaling using true interpolation.
Automatic contrast and brightness correction.
Error diffusion or programmable dither arrays.
By each CHIP SELECT (/ROM_CS, /SCS1, /SCS0,
JBIG compression block
/SD_RAS ,/SD_CAS ), FLASH MEMORY and SDRAM are
: JBIG/MH/MR/MMR Comp. & Decomp.
selected, and DATA is accessed by HALF WORD unit.
Inkjet engin format
: Rotates data to suit the Lexmark engin format
3-5 Image processing part (U21)
Printer Interface section
: Supports a single byte DMA with 150MHz clock speed.
3-5-1 GENERAL DESCRIPTION
Microcontroller interface part
: 8bit multiplexed bus acts as address and data bus
Image Processor OA-980(U21) is mainly configured with
On-chip Controller(8bit), Scanner Interface Section(PI), General purpose input and output port
Image Processing Section(IP), Memory Interface : 30 GPIO pins.
Section(MI), JBIG Comp & Decomp Section, Rotate and
Inkjet Engine Section, Printer Interface Section(PO), 1284
Parallel Port Interfaced and Host Interface Section(HI).
(See Figure 14 )
3-5-1-1 Physical
Core Process Drive power Package Design
/frequency
8bit Micro- 0.35U 3.3V 208pin OASIS
controller CMOS 75MHz QFP
Repair Manual
3-20
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
Repair Manual
3-21
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
ROM connected
Boot ROM checks
connection of ROM
No ROM
"Ready"
Repair Manual
3-22
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
Unlike the existing DuoIP sequence, OA-980 exchanges 1. Multiplexed 8bit Bus(data & address) mode
Command and data with Jupiter 3 in the Multiplexed 8bit
Bus(data & address) mode. Namely, it does not receive nce Jupiter3 may not support Multiplexed 8bit Bus(data &
Address and Data simultaneously, but receive data after address) mode used by OA-980, it configured a circuit addi-
receiving Address first using Data Bus of Jupiter3. tionally so that mutual Interface may be possible by making
required signal using two NOR GATE(UR16) and one OR
HI Section also supports the data movement in the DMA Gate(U40).
mode. Accordingly, when transmitting large capacity of
Image data(RGB data of MultiMedCard), it uses the DMA As REG_ADDR_VAL(pin27) signal is the signal for OA-980
mode. to play a role of informing that value input into 8bit of OA-
980 Bus is not Data but Address value, when ADDR(10) is
High and /IP_CS, /WR Low, High shall be generated as
shown in the circuit diagram. See figure (16). At this time,
since /WR_L(pin31), the Write signal of OA-980, should be
maintained in High, the signal shall be generated in case
actual Write is accomplished with one OR Gate(U18),
namely, only when ADDR(10) is Low, When
REG_ADDR_VAL (pin27) is High, input the Address value
of OA-980, and when Low, from the standpoint of Jupiter3,
it may Read or Write One Byte Data using two Cycles by
Reading or Writing relevant Data of (to) Address.
Repair Manual
3-23
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
Repair Manual
3-24
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
3-5-2-5 Image Processing Section(IP) 3-5-2-8 Rotate and Inkjet Engine Section
After performing color compensating required for the After Image CMYK Data which ended all image processing
System for RGB digital data input, it conducts the role of is converted to Format so that Inkjet Printer Engine may
converting to CMYK data printable. IP Block consists of four print, it plays the role of saving them on the external
Modules mainly. SDRAM(U27).
- Photo text detect The Data stored in the external SDRAM(U27) is transferred
- Zoom and dpi adjust to Head Control Part of Jupiter3 through MI and HI Block of
OA-980 by DMA of Jupiter3, and then printed by Spitfire.
- Color space conversion
- Half toning and loss less JPEG
3-5-2-9 Printer Interface Section(PO)
When the Image process required for PC Scan (See Fig.
19) is completed, OA-980 requests that /IP_REQ signal in
3-5-2-6 Memory Interface Section(MI) PO_Block should take the Scan Image Data from the
External DMA Block of Jupiter3(U15). The External DMA
MI Block consists of four Channels, located between exter-
Block of Jupiter3(U15) generates not only /IP_ACK signal
nal SDRAM(U27) and blocks inside OA-980, and is con-
to bring Data by Byte as the unit but also /RD signal to bring
trolled so that the flow of all data may be accomplished more
the Data. The External DMA Block of Jupiter3(U15) stores
efficiently.
the Data in SDRAM(U9) and then restore /IP_ACK as
"High" to receive a next Data/.
As DMA Timing properties between Jupiter and OA-980 do
3-5-2-7 JBIG Comp & Decomp Section not match, /IP_ACK0 is separately created to prevent BUS
collision by using one OR-Gate(U18-3) so that OA-980 may
By condensing Image data processed at Blocks into JBIG use the BUS only in /RD in the way of inputting the /ACK
algorithm and save them in external SDRAM(U27), it shall signal into OA-980 only when /RD is actually produced,
have Memory domain used more efficiently. Naturally, even while Jupiter3 may use in /WR, as shown in the Timing of
when moving Image data which was condensed to JBIG, to Fig. 18. That is, since OA-980 sends Data to BUS during
other block, it is conveyed to Image data freed from conden- /ACK signal section, BUS collision occurs between DMA of
sation. Jupiter3 and /WR section, where /RD, /WR are all carried
out during /ACK.
Repair Manual
3-25
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
Repair Manual
3-26
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
Repair Manual
3-27
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
Repair Manual
3-28
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
Repair Manual
3-29
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
3-6-2 ADC
Description ADC(U16) is the input data that change the Color Mono
analog signal of RGB to the digital signal of 16bit (8bit + VSMP 800ns(1.25MHz) 400ns(2.5MHz)
8bit) so that it may be used as the input of OA-980(U21),
image processor, while VSMP(_ADC_VSMP) is used as a ADC_CLK 133ns(7.5MHz) 133ns(7.5MHz)
sampling signal for each pixel of RGB. That is, it controls VSMP:MCLK 1:6 1:3
the signal for one pixel like CLK1,CLK2 of CCD and its
maximum sampling rate is of color 2MHz mono 4MHz.
MCLK(ADC_CLK) is CLK for the signal of VSMP, the rela-
tion between MCLK and VSMP is as follows. The relations among SCK(ADC_SCK), SDI(ADC_SDI) and
SEN(ADC_SEN) are equivalent to the control bit for regis-
ter setting to mode, output signal appears in 8bit unit from
OP0 to OP7, and 5V/3.3V will be used as the power source.
ADC_CLK
VSMP
OP[7:0] RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA BA BB
GB BA BB RA RB GA GB
(DEL = 00)
OP[7:0] BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA BA BB
GB BA BB RA RB GA GB RA RB GA GB
(DEL = 01)
OP[7:0] GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB
(DEL = 10)
OP[7:0] RA RB GA GB BA BB RA RB GA GB BA BB RA RB GB BA
GA BB RA RB GA GB BA BB RA RB GA GB BA BB
(DEL = 11)
ADC_CLK
VSMP
OP[7:0] RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA BA BB
GB BA BB RA RB GA GB
(DEL = 00)
OP[7:0] BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA BA BB
GB BA BB RA RB GA GB RA RB GA GB
(DEL = 01)
OP[7:0] GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB
(DEL = 10)
OP[7:0] RA RB GA GB BA BB RA RB GA GB BA BB RA RB GB BA
GA BB RA RB GA GB BA BB RA RB GA GB BA BB
(DEL = 11)
Repair Manual
3-30
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
THUNDERBOLT ASIC is configured with SERIAL INTERFACE INPUT PORT interfacing Main controller, 2 DC-DC Converter
Controllers, Power On Reset Generation Circuit, and Motor drive part.
Tcs-sclk
Tcs-sclk
/ TBCS
TBCLK
Tdsu Tdhd
SDI stays at
TBDO bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 bit 8 bit 9 bit 10 bit 11 bit 12 bit 13 last value
LSB MSB
time
Repair Manual
3-31
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
1 CR MOTOR specification
CR MOTOR performs reciprocating movement of CARRIAGE from side to side so that INK CARTRIDGE may print on the
paper.
MOTOR TYPE : PM DC MOTOR declination
Drive voltage : +30VDC
Winding line resistance : 12 2
Driver IC : Thunderbolt
2. CR MOTOR drive
2-1. DC Motor operation
DC Motor drive uses positive phase terminal(+) and anti-phase terminal(-) bound together respectively using 2nd Motor
Driver(MD2) of Thunderbolt ASIC inside, and controls two-way operation of DC motor, by receiving input of "DIR_DCM,"
7th bit among "PWM"(DC-motor Pulse Width Modulation) signal, output of Jupiter-III, and 13Bit Serial Port Inputs("TBDO"
Signal) coming into Thunderbolt ASIC transmitted from Jupiter-III. This Driver is driven by VBULK power source(+30V),
and on terms of Motor Stall not being generated, it is designed to supply 750mA current, and 2.4A current to output ter-
minal for maximum length of 100ms.
Repair Manual
3-32
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
2) DC Specification
3) AC/Transient Specifications
Name Description Condition Min Nom Max Units
fPWM PWM frequency Ta = 25C 19 20 21 KHz
4) Truth Table
3-1. LF MOTOR
MOTOR TYPE : 2-2 Bi-polar Stepper Motor
Drive Voltage : +30V
Spherical line resistance : 5 7%
Driver IC : Thunderbolt
Repair Manual
3-33
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
2) DC Specification
Repair Manual
3-34
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
OPE
OPE BOARD is separated from the Main Board functional- OPE and MAIN exchange information mutually by using
ly, and operates entire Micom(HT48C5A-000Z) in the asynchronous communication mode(UART), and in full
Board. OPE and Main exchange mutual information using duplex. Band rate is 9600bps, and uses 7.37MHz resonator
UART(universal asynchronous receiver/transmitter) chan- as oscillating element. It engages in communication with
nel. Also, Resetting of OPE is designed to control at the 8bit data without parity bit. UART line has two lines for Tx
Main. Micom in OPE performs key-scanning and LCD, LED and Rx, and the default level is in the 'high' state. For com-
display control, and senses document detect, Scan position munication, the start bit(low level) is transmitted before 8bit
and so on. When information is generated from OPE(key data. When the data transmission(8bit) is completed, the
touch, sensor level change, etc.), it sends specific code high state is maintained as the stop bit(high level) is trans-
coping with the situation to Main, and the Main operates mitted. Data is transmitted from LSB(DO), and MSB(D7) is
system by analyzing this code. If the Main tries to display transmitted lastly.
data on OPE, the Main sends data to OPE via UART line
on the basis of the format specified, and OPE displays it to
LCD.
This system does not apply document detect and SCAN
position.
Repair Manual
3-35
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
(Note) 1. After this, keep waiting until there is response from the Main.
2. The case of longer time(longer than 10ms) elapsed longer than waiting time required for Interface is regarded as fail
3. After this code went out, then data requested it goes out.
KEY MATRIX
(1_H) (2_H) (3_H) (4_H) (5_H) (6_H) (7_H) (8_H)
(_1H) INK RESERVED RESERVED RESERVED CONTRAST RESERVED RESERVED RESERVED
(_2H) PAPER RESERVED RESERVED RESERVED COPY PAGE RESERVED RESERVED RESERVED
(_3H) SET UP RESERVED RESERVED RESERVED ZOME RETE RESERVED RESERVED RESERVED
(_4H) SCROLL NOLUM-UP RESERVED RESERVED RESERVED BLACK COPY RESERVED RESERVED RESERVED
(_5H) SCROLL NOLUM-DOWN RESERVED RESERVED RESERVED COLOR COPY RESERVED RESERVED RESERVED
(_6H) CANCEL RESERVED RESERVED RESERVED SPECIAL RESERVED RESERVED RESERVED
(_7H) ENTER RESERVED RESERVED RESERVED SCAN TO RESERVED RESERVED RESERVED
(_8H) QUALITY RESERVED RESERVED RESERVED POWER RESERVED RESERVED RESERVED
Repair Manual
3-36
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
1. DATA TYPE
DATA types Meaning Remarks
a1 H LCD DISPLAY DATA(FULL LINE)
a2 H LCD DISPLAY DATA(1'ST LINE)
a3 H LCD DISPLAY DATA(2'ST LINE)
a4 H LED DATA
b1 H Change of LCD types
2. NO. OF DATA
In case DATA is N BYTE, N+1
3. DATA
In case DATA TYPE is LCD DATA, it is configured with ASCII CODE to be displayed.
In case DATA TYPE is LED DATA, it is 1 BYTE.
DATA BIT BIT 0 BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7
LED NO. LED 0 LED 1 LED 2 LED 3 LED 4 LED 5 LED 6 LED 7
4. CHECK SUM
The value done XOR all of them from DATA TYPE to DATA.
In case the MAIN does not change the LCD types, it is the Default LCD state of OPE MICOM.
Repair Manual
3-37
Samsung Electronics
- This Document can not be used without Samsung's authorization -
CIRCUIT DESCRIPTION
It has 32 I/O Ports, and 24 Ports of them are arranged to decide I/O direction with Software Control, and the rest 8 Ports are
arranged to be used for Input or Output only. All of I/O Ports are classified into four Blocks according to the characteristics of
I/O Control, and each Block consists of 8 Ports.
LCD ON/OFF
In case of VCC applied to LCD No. 3 PIN (BACKGROUND LEVEL), all the LCD screen will be erased. When the power is
applied, MICOM PA0~7 are Default High LEVEL, so LCD will be OFF. From Jupiter3, LCD will be ON simultaneously with OPE
reset.
Q1, Q2 have the function of simply doing On/off only.
When pressing the Power Key, actual power is not turned Off but 11.75V terminal of Thundervolt Off in the Main, while simply
the LCD DISPLAY should not appear in OPE. At this point, Micom should be operated normally to recognize the Key when
pressing the Power key again. [The same effect as Power save]
Repair Manual
3-38
Samsung Electronics
- This Document can not be used without Samsung's authorization -
4
SCHEMATIC DIAGRAMS
4. Schematic Diagrams
4-1 Main Circuit Diagram (1/8)
1 2 3 4 5 6 7
A A
SHEET 2 SHEET 6
CONNETOR PART IMAGE PROCESSING PART
CONN.SCH SCANIP.SCH
B B
SHEET 3 SHEET 7
JUPITER.SCH
ALL RIGHTS RESERVED
C C
SHEET 4 SHEET 8
SHEET 5
DRIVER PART
DRIV.SCH E
E SIGN
C
A H E D
R E N W SCX-1100
P C G G Main Board
. K . .
REV 0.2
Repair Manual
4-1
Samsung Electronics
1 2 3 4 5 6 7
R8
5.1K
A CN1-26
CN1-25 CHY
30V
PULLUP A
CN1-24 CHX C205
CN1-23 100nF
CN1-22 3.3V
CN1-21 _SF_POR 5V 5VA R155
CN1-20 ACLK C50 1.5K
CN1-19 AGATE
CN1-18 LDCS C66 C67 C49 330uF
R43 BD6 0,5% DGND R153 10K
CN1-17 LATCHCTL 100nF 100uF 100nF 10K 50V R154 USB20-4W2100
CN1-16 PCLK CN11-1 16V 10K BD13
CN1-15 CN11-2 C119 C118 CN8-1
100nF 100uF R144 BD11
CN1-14 PDATA3 CN11-3 BD12 CN8-2
CN1-13 PDATA2 CN11-4 16V R152 CN8-3
L11 0 BD10
CN1-12 PDATA1 BD7 0,5% CN8-4
CN1-11 PDATA0 L5 C204 C203 C209 L9
CN1-10 PLOAD 22pF 22pF 100nF
CN1-9 PENABLE L6 0 GND30
CN1-8 PH_ID1 AGND
CN1-7 PH_ID2 DGND
L12 0 L10
CN1-6 OK2PRT 0
CN1-5
CN1-4 C1 C7
CN1-3 220pF 220pF DGND FGND
CN1-2
CN1-1
5V
30V 5V 5V
GND12 GND30 DGND (UNUSED)
Q9
5V KSA1182-Y
B R384 B
R147 10K
R148 10K
R149 10K
R207 10K
CN7-1 1.5K
1 DIN15
R380 180K
5V 2 KEYTONE Q10 CN16-1
3 OPE_TXDD CN16-2
4 2SC2812L6-TA
_OPE_RES CN16-3
5 OPE_RXD R383
68K CN16-4
CN16-5
_STB CN16-6 ADF_PHA
CN14-1 CD(0:7) OPE_MAGIC ADF_IA0
CN16-7
CN14-2 CN16-8 ADF_IA1
CN14-3 C97 C80 C81 C82 CN16-9 ADF_PHB
CN14-4 100nF 100pF 100pF 100pF CN16-10 ADF_IB0
CN14-5 CN16-11 ADF_IB1
CN14-6 DGND _ADF_DET
CN16-12
CN14-7 CN16-13 _D_DET
CN14-8 DGND CN16-14 _D_SCAN
(UNUSED)
SAMSUNG ELECTRONICS CO., LTD.
0 5V
CN14-16
CN14-17 C336 DGNDFGND
CN14-18 100pF
CN14-19 5V DGND
R138 47K
R136 47K
C208 11.75VA GND30
CN14-20
CN14-21 100nF
CN14-22
CN14-23 DGND
C CN14-24 CN9-1 C
CN14-25 3711-002815 3.3V
CN14-26
CN14-27 1 MODEM_RX
CN14-28 DGND 2
CN14-29 3 MODEM_TX1 R146 SPK_OUT+ CN13-1
CN14-30 4 MODEM_TX2 4.7K CN13-2
CN14-31 _INIT 5 SPK_OUT-
CN14-32 _ERROR 6 REMOTE
CN14-33 7
8 R137 1K
CN14-34 _HOOK_OFF R145 100
CN14-35 9 _RING_DET CN12-1 COVER_OPEN (Unused)
CN14-36 _SLCTIN 10 R135 1K CN12-2
C338 11 DP CN12-3
C337 12
100pF C197 CN3-1
100pF 13 RECALL CR_NA
100nF CN3-2
14 CN3-3
DGND CR_A
R125 5045-03A
LIU C182 C181 Q5 3 3K
DGND DGND 100nF 100pF 2SC2812L6-TA 1TP230 3711-000198|scon_pin3_2.5mm
_CML_ON
2
C194 C R126 DGND
100pF 2K
(UNUSED) B E
47pF
47pF
1 Q1
CN5-3 LAMP_ON 2SC2812L6-TA C
CN5-2
R373 1K 2 A H E D SCX-1100
CN5-1
4.7K R E N W
C32
C35
C38
C39
FPC_24
CD74HCT244M P C G G Main Board
CCD DGND . K . . REV 0.2
AGND GND12 DGND
DGND DGND
DGND DGND
DGND DGND
Repair Manual
4-2
Samsung Electronics
1 2 3 4 5 6 7
3.3V
BD4
0,5%
3.3V
VB2
A C76
100uF
C92
100nF
C88
100nF
C87
100nF
C110
100nF
C78
100nF 3.3V R77
A
2.5V 16V 100K
C111 U13
U11 100nF XC61FN3112MR
3.3V
LF25CDT
100nF
C109
_POR
1 3 TP3
I0 OUT
GND DGND C90
C64 C79 10nF
2 C65 C99 C113 C77 C91 PLLGND 100nF
100nF 1uF 100nF 100nF 100nF 100nF
50V 3.3V
DGND
DGND DGND DGND
DGND PLLGND R101
4.7K
3.3V
DATA(0:15) R76 0
R100 0 _POR
_F_POR C220 R3
1nF 10K
3.3V
R93 C216
100 R107 100 C219 22pF
245DIR
ADDR(0:19) 100 100nF
R55 _WR
R56 100 DGND
R50 100 _RD
R59 100 _SCAS
R51 100 _SRAS R204 C217
R60 100 _SCS0 3.3K 0.68nF
_SCS1 DGND DGND
R95 100
DGND
SAMSUNG ELECTRONICS CO., LTD.
IPCLK
C93 C89
SCLK 820pF 820pF
U15 R61 100 3.3V
R11 100 SCKE C70
S3C46MOX DQM0 100pF
ALL RIGHTS RESERVED
DQM1
DGND DGND
R75 4.7K
A20
A21 R74 4.7K
A22 R58 100 R94 4.7K
R57 100 R92 4.7K
_OPE_RST R73 100
PD(0:7) _IP_RST
C _TRST
C
RA1
100 TDI
TCK
1/16W TDO DGND
RA2 TMS
100
1/16W
RA5 ACLK 4.7K 4.7K 4.7K 4.7K 4.7K 3.3V
AGATE R64 R78 R65 R62 R63
_P_SLCTIN LATCHCTL
_P_STB 1/16W PCLK
_P_INIT RA4 PDATA3
_P_AUTOFD PDATA2
_P_ERROR PDATA1
P_SLCT 1/16W PDATA0
P_PE RA3 PENABLE
P_BUSY PLOAD
_P_ACK LDCS
1/16W
KEYCLICK
USB_DP
USB_DM TBCLK
PULLUP TBDO
VBUS _TBCS
C215
1nF
DGND
D DGND D
3.3V
C218
22pF
R84 R88
R102 4.7K 4.7K
10M
X3 R89 100
0.32768MHz OK2PRT
OPE_RXD
OPE_TXD
C112 22pF PH_ID2
(Unused) _IP_REQ
_IP_ACK
_P_PICKUP
R80 100 COVER_OPEN
R72 100 PWM
CHYY
E
R87 100
CHXX
DGND
E SIGN
C
A H E D SCX-1100
R E N W
P G G Main Board
C
. K . . REV 0.2
Repair Manual
4-3
Samsung Electronics
1 2 3 4 5 6 7
A A
VB
DQM0
DQM1 R40
3VB 0
_WR SD_CKE
_SD_RAS _SD_CAS SCLK
R32 0 _SD_CAS _SD_RAS
A20 _SCS1
C37
100nF A21
A22 A20
B B
DGND
DGND DGND
DGND
(Unused)
3.3V 3.3V
C18 C4
100nF 100nF
U2-3
SAMSUNG ELECTRONICS CO., LTD.
74VHC08MX
U1-3 U2-4
MC74VHC32DR2 74VHC08MX
DGND DGND
SD_CKE
ALL RIGHTS RESERVED
_SRAS
3.3V VB VB2
D2 _SD_CAS
Q2
KSA1182-Y MMSD914T1 U1-2
R22 0 R21 200 _SCAS
MC74VHC32DR2
R17 1.5K (UNUSED)
R13 180K VB
Q8
2SC2812L6-TA
R12
68K
R16 C5
200 100nF
D D
CHX
C31 C30 DGND
DGND 16V 16V CHXX
5.5V,5V
10uF 10uF
R371 U2-1
100K 74VHC08MX
DGND
DGND
DGND
U2-2 (Unused)
74VHC08MX CHY
CHYY
U1-4
MC74VHC32DR2
C
A H E D
R E N W SCX-1100
P C G G Main Board
. K . .
REV 0.2
Repair Manual
4-4
Samsung Electronics
1 2 3 4 5 6 7
5V 30VA
TBDO
TBCLK
_TBCS
U10
TEA3718S GND30
GND30
R53 1K
C BD3 3.3V
C
CIB32P600NES
5V
C60 R46 C63 R52 5V
820pF 56K 820pF 0.5
C152
100nF
D _SPK_CTL
D
DGND E_DP
_GPIO_CS
DGND
(Unused)
_WR E
U18-2
MC74VHC32DR2
E SIGN
C
A H E D SCX-1100
R E N W
P C G G Main Board
. K . . REV 0.2
Repair Manual
4-5
Samsung Electronics
- This Document can not be used without Samsung's authorization -
SCHEMATIC DIAGRAMS
1 2 3 4 5 6 7
3.3V
BD8
0,5%
DGND 3.3V
ADC_SDI
ADC_SEN
ADC_SCK
U27 SDRAMDATA(0:15)
LAMP_ON K4S641632C
_D_DET
_D_SCAN
B _SF_POR R205 100 B
_MODEM_RST 100
ADF_PHA R115
R117 100
ADF_PHB
ADF_IA0 RA6
ADF_IA1
ADF_IB0 100
ADF_IB1 1/16W
(Unused)
SCAN_PHA
SCAN_PHB
SCAN_IA0 3.3V
SCAN_IA1
SCAN_IB0
SCAN_IB1
ADDR(9:8)
SAMSUNG ELECTRONICS CO., LTD.
DATA(0:7)
100nF
100nF
100nF
100nF
100nF
100nF
100nF
C179
C201
C196
C193
C202
C200
C177
U3-3 DGND
74VHC27
ADDR(10) U21
ALL RIGHTS RESERVED
C198
10uF
_IP_CS OA-980 16V
_WR
U3-2
74VHC27 R374
33
5V
C 3.3V DGND 3.3V 5VA
C
3.3V
TP457
TP460 R128 C127
TP458 4.7K C107 10uF
R116 TP459 DGND 10uF 10uF 16V
4.7K C131
100nF C116 16V C106 C115
100nF 100nF 100nF
_IP_INT U16
_IP_RST TP450 DATA(0:7) WM8192
3.3V DGND
BASEEXT AGND
DGND
MAINEXT
R118 1K DGND
R98 100
IPCLK VOUT_R
VOUT_G
_IP_ACK0 VOUT_B
3.3V
_IP_REQ C105 100nF
DGND
1TP33 AGND
ADC_CLK
1TP232
1TP231 R97 47K _ADC_VSMP
1TP31
D 1TP32
1TP233 ADC_SCK D
1TP237 ADC_SDI
1TP238 ADC_SEN
1TP269
1TP236 C102 R104
1TP234 10nF 4.7K
1TP235 CCD_TG
1TP25 _ADC_VSMP
1TP29 ADC_CLK R105
1TP30 C104
1000nF 4.7K
1TP268 CCD_RS DGND
1TP28 CCD_CLK2
1TP26 CCD_CLK1
1TP27
C94 C114
100nF 100nF
DGND
C103
100nF
AGND
E
DGND
MC74VHC32DR2
ADDR(10)
ED. DATE 1 01.08.06 2 3
_WR_L
E _WR SIGN
U18-3
MC74VHC32DR2
_IP_ACK C
_IP_ACK0
A H E D
R E N W SCX-1100
_RD
P C G G
U18-4
. . . Main Board
K
REV 0.2
Repair Manual
4-6
Samsung Electronics
1 2 3 4 5 6 7
A A
C175 1nF
5V MODEM_TX2
MODEM_TX1
C174 100nF R133 47K
L4 10uH R131 330K C188 100nF
TX
D4
AGND U23-2 C173
DGND MMSD914T1 +3.0V
5V 100nF
MC14053BD
U25-1
RX KA358D-T/F
3.3V
C183 100nF
DGND
3.3V U23-3 U24-2
MC14053BD C187 KA358D-T/F
R141
100nF 47K
ADDR(0:4)
R130 120K C171 100nF
RX
R109
10K
Q3 TX
SAMSUNG ELECTRONICS CO., LTD.
2SC2812L6-TA U19
_MODEM_IRQ 5V _RD
R112 10K _WR FM336R6719-12
_MODEM_CS TX_CTL
R113 C154
10K 1nF
ALL RIGHTS RESERVED
+3.0V
D6
MMSD914T1
DGND DGND
_MODEM_RST
C R122 C148 C
330K
150K
330K
47K
1M
1M
4.7K 100nF
0
0
R157
R160
R156
R158
R161
R163
R162
R164
5V
DGND DGND
R110
100
C206
X2 100nF
28.224MHz
AGND
C122 C123 R159 4.7K C199 100nF
TONE_OUT
27pF 27pF
VOL_0
VOL_1
DGND AGND DGND
5V VOL_2
D D
5V
C213 1nF R165 11.75VA +3.0V
10K U23-1
R166 150K MC14053BD
11.75VA
5V _SPK_CTL
R127
C210 U24-1
24K
1nF KA358D-T/F
C170
11.75V 11.75VA 100nF
C172 R129
BD9 U23-4 100nF 8.2K
CIM21J121NES MC14053BD
DGND C167
C168
C156 TONE_OUT SPK_OUT+ 10uF
100nF
22uF 16V
C214 100nF R167 47K AGND
25V SPK_OUT- AGND
C169 R379 1M C132 100nF C211
100nF KEYCLICK 1uF AGND
U34
C212 MC34119DR2
AGND AGND
E
1uF
AGND TONE_CTL
D7
MMSD914T1
C166
1nF +3.0V DGND
Repair Manual
4-7
Samsung Electronics
1 2 3 4 5 6 7
A A
5V
5V
B C195
5V
3.3V B
100nF C207 C190
100nF 100nF U26
TC74LVX4245MTCX
_STB
DGND
PD(0:7)
CD(0:7)
DGND
CD(0) PD(0)
CD(1) PD(1)
CD(2) HIC1 PD(2)
CD(3) PD(3)
CD(4) SUPER1284 PD(4)
CD(5) PD(5)
CD(6) PD(6)
CD(7) PD(7)
SAMSUNG ELECTRONICS CO., LTD.
3.3V
245DIR
ALL RIGHTS RESERVED
3.3V
C191 C192
100nF 100nF
U33
C 39 RA7
DGND C
_ACK
BUSY _P_ACK
PE P_BUSY
SLCT P_PE
P_SLCT
_P_ERROR
VOL_0 VOL_00
VOL_1 VOL_10
VOL_2 VOL_20
TC74LVX4245MTCX
_P_STB
RA8 39
_AUTOFD _P_AUTOFD
_SLCTIN _P_SLCTIN
_ERROR
DGND DGND
_INIT _P_INIT
D D
E SIGN
C
A H E D
R N W
SCX-1100
E
P C G G Main Board
. K . . REV 0.2
Repair Manual
4-8
Samsung Electronics
1 2 3 4 5 6 7
5V
2
A +5V
1 Q1
KSA1182-Y
A
3
CN2-4 OPE_POW
C13
100nF
5V C1 200
10uF R18
10uF
C4
16V
16V R20
GND 1.5K
CN2-5 5V
R8
22K
D1 3
MMSD914T1 1 Q2
GND5 2SC2812L6-TA
2
R3
/OPE_RST 200 R21
CN2-2 68K
5V
C3 5V 5V
1000nF
R24
150
GND5
GND5
R5 R6
22K 22K U1
R2 2
200 1 Q3 LED1
KSA1182-Y SLS-NNGR202TS
CN2-1 OPE_TXD C5 3
100nF
OPE_RXD
B CN2-3
B
R1
200 GND5
C11 R19 180K
C6 C7 47pF GND5
100pF 100pF R25 1K
CN1-6 R10
paper 22K
LCD_D0
CN1-7
LCD_D1
CN1-8 zoomrete
LCD_D2 R11
CN1-9 setup 22K
ALL RIGHTS RESERVED
LCD_D3
CN1-10
LCD_D4 scroll/volume_up
CN1-11 black copy R12
LCD_D5 22K
CN1-12
LCD_D6
CN1-13
C LCD_D7 color copy C
CN1-14 R13
scroll/volume_down 22K
C8 C9 C10 5V
22pF 22pF 22pF R7
22K
special cancel
R14
22K
GND5 GND5 GND5
HT48R50 scan to enter
GND5 R22
22K
quality power
R23
22K
D3 MMSD914T1
D2 MMSD914T1
D D
5V 5V
R16
10K
CN1-3 3
OPE_POW
R17
680
E
2
CN1-2
GND5
C2
100nF
ED. DATE 1 01.07.2 2 3
1
CN1-1
E SIGN
GND5 GND5
C
A H E D SCX-1100
R E N W
P C G G OPE Board
. K . .
REV 0 .3
Repair Manual
4-9
Samsung Electronics
Magic-V3 POWER
SUPPLY(100-240Vac)
LF1 T1
F1 SQH0350 BD1 NT1 EE2525W D4=SR204 KA78R33
AC250V T 2A TNR1 2KBP06M +3.3V0.8A
DSC10D9
U2 CH1
8 1
C13=10V1000uF
C7=PC630V103
R-30190 1 2
10D471K
C14=16V47uF
CON1-1
R2=1/4W180K
3
C3=222
H
R18=2W2.2K
R1=1W560K
IL1 t C15=1KV102
10D561K
C1=224
C2=104
R21=1/4W22
2t
- +
C5=400V120uF
R3=1/4W/180K
PE
48t =550uH
N
B1=BEAD
CON1-2
3
X GND
C4=222
R19=1/4W/180K
Q2=FQU2N60
9
3t
ZD5=27V
R20=1/4W68K
10
D1=1N4148 D5=ER502 B2=BEAD
Q1
SSP5N80A CH3
C6=1KV331
C8=103 2 CON1-3
R10=330 R11=180 D2=1N4148
R13=510 +30V1.3A
R15=6.8KF
7
ZD1=9.1V
D3=1N4148
R5=47K
R14=6.8K
C12=50V47uF/KMG
R7=3.3KF 1 PC1
R12=1K
ZD4=1W36V
PC1=PC123B
PC123B
C11=50V470uF/KMG
4
ZD2=4.3VB
2
R8=330
12t
3t
C10=1uF
3
Q3=C1008-Y
R9=33
R16=1.8KF
R17=1W0.42(MINI)
Q4=C1008
R4=1W0.42(MINI)
R6=510
C9=103
ZD3=5.6V
6 4 CON1-4
GND
Title
MAGIC POWER SUPPLY CIRCUIT DIAGRAM (Magic-V3)
Size Document Number Rev
B {Doc} 01
Repair Manual
4-10
Samsung Electronics
SAMSUNG