Escolar Documentos
Profissional Documentos
Cultura Documentos
3
Company: Page: 1
Specifier: Project: Mozambique NOB Span
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 10.08.2017
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: Kwik Bolt TZ - CS 1/2 (3 1/4)
Effective embedment depth: hef = 83 mm, hnom = 92 mm
Material: Carbon Steel
Evaluation Service Report: ESR-1917
Issued I Valid: 1.06.2016 | 1.05.2017
Proof: Design method ACI 318 / AC193
Stand-off installation: eb = 0 mm (no stand-off); t = 6 mm
Anchor plate: lx x ly x t = 50 mm x 50 mm x 6 mm; (Recommended plate thickness: not calculated
Profile: no profile
Base material: cracked concrete, , fc' = 4350 psi; h = 300 mm
Reinforcement: tension: condition B, shear: condition B; no supplemental splitting reinforcement present
edge reinforcement: none or < No. 4 bar
Seismic loads (cat. C, D, E, or F) no
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: Page: 2
Specifier: Project: Mozambique NOB Span
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 10.08.2017
E-Mail:
3 Tension load
Load Nua [kN] Capacity f Nn [kN] Utilization bN = Nua/f Nn Status
Steel Strength* 6,530 35,714 19 OK
Pullout Strength* 6,530 18,746 35 OK
Concrete Breakout Strength** 6,530 18,994 35 OK
* anchor having the highest loading **anchor group (anchors in tension)
Variables
Ase,N [mm2] futa [psi]
65 106000
Calculations
Nsa [kN]
47,618
Results
Nsa [kN] f steel f Nsa [kN] Nua [kN]
47,618 0,750 35,714 6,530
2500
'
fc
Npn,f'c = Np,2500 refer to ICC-ES ESR-1917
f Npn,f'c Nua ACI 318-08 Eq. (D-1)
Variables
f'c [psi] Np,2500 [kN]
4350 21,863
Calculations
2500
'
f c
1,319
Results
Npn,f'c [kN] f concrete f Npn,f'c [kN] Nua [kN]
28,839 0,650 18,746 6,530
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: Page: 3
Specifier: Project: Mozambique NOB Span
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 10.08.2017
E-Mail:
Ncb = (AA ) y
Nc
Nc0
ed,N y c,N y cp,N Nb ACI 318-08 Eq. (D-4)
f Ncb Nua ACI 318-08 Eq. (D-1)
ANc see ACI 318-08, Part D.5.2.1, Fig. RD.5.2.1(b)
ANc0 = 9 h2ef ACI 318-08 Eq. (D-6)
( )
1
y ec,N = 2 e'N 1,0 ACI 318-08 Eq. (D-9)
1+
3 hef
y ed,N = 0,7 + 0,3 ( ca,min
1,5hef )
1,0 ACI 318-08 Eq. (D-11)
y cp,N = MAX (
ca,min 1,5hef
cac
,
cac )
1,0 ACI 318-08 Eq. (D-13)
1,5
Nb = kc l fc hef
'
ACI 318-08 Eq. (D-7)
Variables
hef [mm] ec1,N [mm] ec2,N [mm] ca,min [mm] y c,N
83 0 0 1,000
Calculations
ANc [mm2] ANc0 [mm2] y ec1,N y ec2,N y ed,N y cp,N Nb [kN]
61331 61331 1,000 1,000 1,000 1,000 29,222
Results
Ncb [kN] f concrete f Ncb [kN] Nua [kN]
29,222 0,650 18,994 6,530
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: Page: 4
Specifier: Project: Mozambique NOB Span
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 10.08.2017
E-Mail:
4 Shear load
Load Vua [kN] Capacity f Vn [kN] Utilization bV = Vua/f Vn Status
Steel Strength* 0,800 15,888 6 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength** 0,800 40,910 2 OK
Concrete edge failure in direction ** N/A N/A N/A N/A
* anchor having the highest loading **anchor group (relevant anchors)
Variables
Ase,V [mm2] futa [psi]
65 106000
Calculations
Vsa [kN]
24,443
Results
Vsa [kN] f steel f Vsa [kN] Vua [kN]
24,443 0,650 15,888 0,800
( )
1
y ec,N = 2 e'N 1,0 ACI 318-08 Eq. (D-9)
1+
3 hef
y ed,N = 0,7 + 0,3 (ca,min
1,5hef )
1,0 ACI 318-08 Eq. (D-11)
y cp,N = MAX (
ca,min 1,5hef
cac
,
cac )
1,0 ACI 318-08 Eq. (D-13)
1,5
Nb = kc l fc hef
'
ACI 318-08 Eq. (D-7)
Variables
kcp hef [mm] ec1,N [mm] ec2,N [mm] ca,min [mm]
2 83 0 0
Calculations
ANc [mm2] ANc0 [mm2] y ec1,N y ec2,N y ed,N y cp,N Nb [kN]
61331 61331 1,000 1,000 1,000 1,000 29,222
Results
Vcp [kN] f concrete f Vcp [kN] Vua [kN]
58,443 0,700 40,910 0,800
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: Page: 5
Specifier: Project: Mozambique NOB Span
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 10.08.2017
E-Mail:
6 Warnings
The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.).
This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is
assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum
required anchor plate thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the
rigid base plate assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the
existing conditions and for plausibility!
Condition A applies when supplementary reinforcement is used. The factor is increased for non-steel Design Strengths except Pullout
Strength and Pryout strength. Condition B applies when supplementary reinforcement is not used and for Pullout Strength and Pryout
Strength. Refer to your local standard.
Refer to the manufacturer's product literature for cleaning and installation instructions.
Checking the transfer of loads into the base material and the shear resistance are required in accordance with ACI 318 or the relevant
standard!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: Page: 6
Specifier: Project: Mozambique NOB Span
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 10.08.2017
E-Mail:
7 Installation data
Anchor plate, steel: - Anchor type and diameter: Kwik Bolt TZ - CS 1/2 (3 1/4)
Profile: no profile Installation torque: 0,054 kNm
Hole diameter in the fixture: df = 14 mm Hole diameter in the base material: 13 mm
Plate thickness (input): 6 mm Hole depth in the base material: 102 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 203 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions for use is required.
25 25
25
25
1 x
25
25
25 25
Coordinates Anchor mm
Anchor x y c-x c+x c-y c+y
1 0 0 - - - -
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: Page: 7
Specifier: Project: Mozambique NOB Span
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 10.08.2017
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan