Escolar Documentos
Profissional Documentos
Cultura Documentos
INSTALLATION MANUAL
Applied Machines: C364/C284/C224
COLOR MFP: 36 ppm/28 ppm/22 ppm
Product Code: A161/A4FK/A4FM
2. Hinge cover
(small) II. Installation procedures
1 1. Turn off the machine and unplug the power cord
from the power outlet.
A3CFIXC002DA
2. Hold the reverse automatic document feeder as
shown in the illustration and remove it from the
3. Shoulder
2 carton.
screw
4582U010AA
Note:
4. Mounting To prevent breakage, do not hold the reverse auto-
screw 2 matic document feeder by the four corners.
A143IXC017DA
5. Chart
9J07IXC048DA
6. Installation
manual
1 set
A3CFIXC038DA
4980IXC019DA
A3CF-9550-00
E-1
3. Remove the protective tape and protective mate- 5. Place the reverse automatic document feeder in
rials and remove the protective plastic bag of the position.
relay harness.
A3CFIXC006DA
A3CFIXC036DA
A3CFIXC007DA
A3CFIXC008DA
A3CFIXC005DA
E-2
8. Connect the two connectors of the reverse auto- III. Adjusting the height
matic document feeder to the main unit, and
attach the harness with a cable tie at the position 1. Check the clearance between the upper face of
shown in the illustration. scanner and the protrusion on the reverse auto-
matic document feeder side. (Three spots)
* There must be no clearance between the protru-
sion on the reverse automatic document feeder
and the upper face of scanner.
A3CFIXC009DA
Protrusion
Protrusion
A3CFIXE031DA
A3CFIXC011DA
Claws B
Claws A
A3CFIXC030DA
E-3
2. If there is any clearance, adjust the height by 5. Make copies 5 times repeatedly in single side
turning the adjustment screw on the right side mode.
viewed from the back. 6. Fold all 5 sample copies as illustrated and check
Clockwise: The rear side will move up. for any deviation.
Counterclockwise: The rear side will move down. Deviation on the sample will be Y.
If further adjustment is required, adjust the height
by using the adjustment screw on the left side
viewed from the back together.
Clockwise: The rear side will move up.
Counterclockwise: The rear side will move down.
Y Y
X X
4. Place the chart in the document feeding tray (with 9. Loosen the nut shown in the illustration.
the side having an arrow facing up).
Nut
A3CFIXE033DA
A3CFIXC013DA
E-4
10. When the difference of the deviations is positive 12. After completing the adjustment, tighten the nut
(+), turn the screw counterclockwise using a loosened in step 9.
slotted screwdriver. 13. Attach the two supplied hinge covers as shown
Note: in the illustration.
Look at the guide lines when making the adjust- Hinge cover
ment. (large)
When turning the screw, be sure not to raise the
reverse automatic document feeder until in an
upright position.
* To prevent the adjustment screw breakage, be
sure to follow the above instructions.
Hinge cover
(small) A3CFIXE034DA
Guide lines
14. Tighten the mounting screw on the right hinge
that has been loosened in step 8 using a screw-
driver.
A3CFIXC013DA
Guide line
6. Press the Start key.
7. Check that Adjustment Result is OK and then
touch SET.
8. Touch END.
9. Touch Mixed original size adjustment.
A3CFIXC017DA
E-5
10. Place the chart in the document feeding tray 21. Press the Start key.
(lengthwise). 22. Check that Adjustment Result is OK and then
touch SET.
23. Touch Main Scanning (Front).
24. Place the chart in the document feeding tray
(with the side having an arrow facing up).
A3CFIXC028DA
A3CFIXC013DA
A3CFIXC029DA
E-6
34. When all the adjustments are completed, set the 36. Measure the values a, b and c of the chart
chart to the document feed tray (with the side and the sample copy.
with an arrow facing up), and take the sample When measuring the value a, use the sample
copy at the same magnification. copies which printed in step 34 and 35.
37. Check to make sure that the difference of the
chart and the sample copy is within the specified
range.
Specifications a: 0 2.0 mm for the first and the
second page
Specifications b: 0 2.0 mm
Specifications c: 0 1.0 mm
a
35. Set the chart face down and take the sample
copy (duplex mode).
c
9J07IXE050DA
Stopper
A3CFIXE035DA
E-7
SP-501 Stamp Unit
INSTALLATION MANUAL
2. Stamp
1
4614U002AA
3. Installation
manual
1 set
4980IXC019DA
A3CFIXC024DA
After unpacking, be sure to get rid of the 5. Remove the ground terminal. (One screw)
packaging materials and keep them out of
the reach of children.
Putting the head in the plastic bag
involves danger of suffocation.
A3CFIXC023DA
E-8
6. Mount the stamp in stamp unit. III. Setting
Note:
1. Plug the power cord into the power outlet and
Align the round pin of the stamp with the slit in the
turn on the machine.
stamp unit side.
2. Display the Service Mode screen.
(For details of how to display the Service Mid-
eastern, see the service manual.)
3. Touch System 2.
4. Touch Stamp.
5. Touch Set.
6. Touch END.
7. Touch Exit on the Service Mode screen.
4614IXC007DA
A3CFIXC026DA
A3CFIXC027DA
E-9