Escolar Documentos
Profissional Documentos
Cultura Documentos
AVC118
Instruction Manual
Revision 2.0A
Mar. 2012
SHENZHEN ONTIME TECHNOLOGY CO.LTD
Introduction
The AVC-118 is a voltage sensing torch height control system
constant, and the cutting arc voltage will be changed with the
then control the distance between cutting torch and work piece
via the lifting motor in order to keep the arc voltage within a
corresponding range.
Specifications
Work power: DC24V10%, 3-5A.
The total power of the DC supply must be 10W bigger than the
Accuracy: 1V to 5V adjustable.
Outline: 240mm/210mm/60mm(L/W/H).
3
SHENZHEN ONTIME TECHNOLOGY CO.LTD
Pictures
4
SHENZHEN ONTIME TECHNOLOGY CO.LTD
System connection
AVC118 Controller
CNC
SYSTEM
START
MOTOR
PRO SW
SHIELD
WORK PIECES
GROUND
5
SHENZHEN ONTIME TECHNOLOGY CO.LTD
Connectors
5 1 1 7 GND
9 6 1 5
Terminals outline
switches.
6
SHENZHEN ONTIME TECHNOLOGY CO.LTD
TERMINALS DEFINITION
NAME TERMINAL SIGNAL FUNCTION
5 NC
9 NC
J5SHIELD CAP.
terminal.
8
SHENZHEN ONTIME TECHNOLOGY CO.LTD
J4 J5
9
SHENZHEN ONTIME TECHNOLOGY CO.LTD
CNC INTERFACE
J1: connected to the CNC control system.
Terminal description:
J1-1: AUTO
J1-2: UP
J1-3: DOWN
Start cutting cycle signal from the CNC, this signal must be
level: LOW.
J1-5: NC
J1-6: MOTION
illustration.
J1-7: NC
J1-8: CNC_COM
11
SHENZHEN ONTIME TECHNOLOGY CO.LTD
Limit switch
PLASMA START
Terminal: J3-5 and J3-5. Relay contact output, 10A/250V.
12
SHENZHEN ONTIME TECHNOLOGY CO.LTD
switch.
When more than one proximity switch used, the user can
connection illustration.
DC24V+
SIGNAL
DC24V-
13
SHENZHEN ONTIME TECHNOLOGY CO.LTD
Through this lock terminal, Connect the shield cap lead wire
(as the Ohmic IHS sensing signal) to the SHELD CAP terminal.
SHIELD
CAP
14
SHENZHEN ONTIME TECHNOLOGY CO.LTD
Operation mode
The AVC118 will work in auto mode after power on. This
the arc voltage and modify the torch height correctly during
Operational keys
MEMU --- Menu key
15
SHENZHEN ONTIME TECHNOLOGY CO.LTD
arrow key to select menu items, press the ENTR (enter) key to
displayed on the LCD display and the cursor blinks, after that,
(millisecond).
Caution: if the IHS time is setup to zero, the controller will not
execute initial height setup procedure and will start arc directly.
16
SHENZHEN ONTIME TECHNOLOGY CO.LTD
You have to setup the initial torch height manually when start
arc.
above.
IHS Test
Press the MENU key once while standby, the controller will
arrow key to select menu items, press the ENTR (enter) key to
information. Now the controller will ask you to press the ENTR
key again to confirm and start the IHS test procedure. Now
you can press the MENU key to exit or the ENTR key to start
the IHS test procedure, you can also press the UP or DOWN
time. During the IHS test procedure you can press the ENTR
Arc Test
Press the ARC_TEST key while standby, the controller will
enter into arc test interface, the controller will ask you to press
the ENTR key to confirm and start the arc test procedure. You
can press the ARC_TEST key to exit or the ENTR key to start
the arc test procedure. During the arc test procedure you can
press the ENTR key to stop the procedure manually. After the
standby status.
performance.
18
SHENZHEN ONTIME TECHNOLOGY CO.LTD
Press the MENU key once while standby, the controller will
DOWN arrow key at the same time for about 3 seconds, then
release the key, the controller will enter into inner parameters
setup interface.
return. Press the MENU key to exit to standby status after all
lifting motor.
Range:60-120default120.
lifting motor.
Range:10-120default30.
motor.
Range: MIN_PWM-MAX_PWMdefault30.
motor.
Range: MIN_PWM-MAX_PWMdefault90.
lifting motor.
Range: MIN_PWM-MAX_PWMdefault120.
1 : enable brake.
Default: 1.
Range:1-20default10
Unit: ms (millisecond)
Unit: ms (millisecond)
21
SHENZHEN ONTIME TECHNOLOGY CO.LTD
adjustment function.
collision.
job.
Range:5-50V, default:10.
default: 0.
of the controller.
23
SHENZHEN ONTIME TECHNOLOGY CO.LTD
default: 1.
Unit0.1second.
arc.
Range:10-60default: 20.
zero itself.
25
SHENZHEN ONTIME TECHNOLOGY CO.LTD
TROUBLE SHOOTING
26
Foxit PDF Editor -
(c) by Foxit Software Company, 2004
27