Escolar Documentos
Profissional Documentos
Cultura Documentos
of Glass/Epoxy Composites
ABSTRACT: This study reports the method of recovery of glass fibers from glass/epoxy composites
through the solvent method. It is possible to decompose epoxy resin with a yield of more than
99 wt% soluble products in a nitric acid solution (8 M) at 90 C for 5 h. The decomposition rate of
epoxy resin increases with an increase in temperature and concentration of acid solution. The glass
fibers can be recovered with very little contamination and they have a tensile strength reduction of
3.5% under decomposition conditions of T 70 C, t 250 h, C 6 M and 6 g/100 mL. These
fibers can be used as reinforcement to prepare new composites. The interlaminar shear strength
(ILSS) of recovered short fiber-reinforced composites produce strength reductions of only 2.5%
compared with pristine composites.
INTRODUCTION
LASS FIBER/EPOXY COMPOSITES are attractive materials for the automotive and
G aircraft industry, but one barrier to their increased use is the recycling difficulty. The
epoxy resin in the cast-off cannot be melted down and remolded as is done in the
thermoplastic industry. With the increasing landfill casts, there is an urgent need to
develop recycling technologies for composite materials.
The majority of work on composite recycling is concerned with grinding the composites
into a suitable size to be used as fillers in new composite materials [13]. Masatashi [4]
found that using glass/epoxy composites as fillers for epoxy resin could yield products
with better strength and thermal expansion properties when compared to those made with
conventional fillers. Other recycling processes based on pyrolysis have also been
considered [5,6]. This process breaks polymeric waste into reusable fuel oils and
hydrocarbon gasses in the absence of air. A sheet molding compound (SMC) of glass/
polyester composites was pyrolyzed by Torres et al. [7]. The liquid obtained can be used as
petrol. Combustion with energy recovery is another means of recovering some value from
scrap composites [8]. In these processes, carbon- and aramid-reinforced composites
destroy valuable materials and can be a source of pollution.
A solvent recycling method in which valuable carbon fibers can be recovered has
already been described [9]. In this study, this method is further described, the recycling
Journal of REINFORCED PLASTICS AND COMPOSITES, Vol. 25, No. 14/2006 1525
0731-6844/06/14 15259 $10.00/0 DOI: 10.1177/0731684406066748
2006 SAGE Publications
EXPERIMENTAL
Materials
The epoxy composites with 67 wt% unidirectional glass fiber were prepared in a
laboratory. The bisphenol A type epoxy resin (E-44) and curing agent (IPDA) were used as
a matrix. The curing conditions were 80 C for 2 h and 150 C for 4 h. The composites were
cast to 200 mm 6 mm 2 mm bar.
Decomposition Conditions
Each composite specimen was put into a specially designed glass vessel (D 100 mm,
L 300 mm) and then immersed in 100 mL nitric acid solution. The decomposition
temperature was controlled in a water bath. The feedstock ratio is defined as the ratio of
resin weight in composite to the volume of the nitric acid solution. The insoluble
composites were separated from the solution at a specific decomposition time and washed
with acetone. After drying at 60 C, the composites were weighed.
The recovered glass fibers were incorporated into epoxy matrices to produce two
different composites. The first sample was made of recovered unidirectional continuous
glass fibers with E-44/IPDA at a content level of 65%w/w. The next sample was 45 mm
short glass fibers which were cut from recovered fibers with E-44/MeTHPA at a content
level of 20%w/w. These two types of composites were prepared again by utilizing virgin
glass fibers, for use as reference samples.
Measurement Methods
The decomposition rate of epoxy resin in composites was determined in each experiment
by weighing the amount of solid residue. The decomposition rate is given by
weight of composites weight of solid residue
Decomposition rate % 100:
weight of resin in composites
The reclaimed fibers were subjected to visual scrutiny via optical and scanning
electron microscopy (SEM) to determine the extent of contamination of the residual
surface. The surface of the glass fiber was also observed and pictured by electron probe
microscopy using a JEOL JCXA-733 instrument.
In order to verify the effect of the recycling process on fiber properties, the tensile
strength of the single fiber was measured according to ASTM-D3379 specification. The
cross-head speed of the MTS materials testing system was 10 mm/min. The interlaminar
shear strength (ILSS) testing of new composites was carried out using an Instron 5569
machine with a cross-head speed of 2 mm/min.
Decomposition of Composites
TEMPERATURE
The decomposition curve for epoxy composites, in 8 M decomposition solution at
5090 C for 5 h, with a 2 g/100 mL feedstock ratio is shown in Figure 1. The increase
in temperature resulted in improvement of the decomposition rate of epoxy resin. The
decomposition rate was about 2.1, 24.9, and 96%, at 50, 70, and 80 C respectively. There
is a great increase in decomposition rate after 70 C. The epoxy resin kept for 6 h
completely disappeared at 90 C.
100
80
40
20
0
40 50 60 70 80 90 100
Reaction temperature (C)
Figure 1. Resin decomposition rate vs reaction temperature.
100
80
Decomposition rate (%)
60
40
20
0
0 2 4 6 8 10
Concentration (M)
Figure 2. Resin decomposition rate vs decomposition solution concentration.
FEEDSTOCK RATIO
The effect of feedstock ratio on the decomposition rate of the resin matrix in composites
under a set of experimental parameters (T 90 C, C 8 M, t 5 h) is presented in
Figure 3. The decomposition rate of the resin decreased slowly as the feedstock ratio
increased. It could be seen that the temperature and concentration of the decomposition
solution was much more effective than the feedstock ratio in increasing the decomposition
rate of the resin matrix. The feedstock ratio can be increased in theory to improve reclaim
efficiency. However, because the increase of feedstock ratio results in a decrease in acid
solution volume, the composites cannot be soaked and decomposed.
FIBER PROPERTIES
Table 1 shows the orthogonal experimental results of the decomposition of epoxy
composites in which the loss of fiber strength can be calculated by dividing the amount of
decrease of single fiber tensile strength of the recovered fiber by the tensile strength of a
80
70
1 2 3 4 5 6
Feedstock ratio (g/100ml)
Figure 3. Resin decomposition rate vs feedstock ratio.
Level Results
1 90 8 6 12 5.2
2 90 6 4 22 10.3
3 90 4 2 82 14.7
4 80 8 4 17 10.4
5 80 6 2 95 11.7
6 80 4 6 240 15.1
7 70 8 2 45 9.1
8 70 6 6 250 3.5
9 90 8 6 710 11.3
single fiber of the original fiber bundle. The sample under decomposition conditions of
T 70 C, t 250 h, C 6 M, and 6 g/100 mL has a minimum fiber tensile strength loss
of 3.5%, while runs at 80 C with 4 M concentration for 240 h produced a maximum
strength reduction of 15.1%. These results are better than the results of the previous study
of the effects of recycling process on the strength of the glass fibers. Pickering et al. [10]
measured a 50% reduction in the strength of glass fibers after heating at 450 C in a
fluidized-bed process.
(a) (b)
Figure 4. SEM micrographs of composites under T 60 C, t 5 h, C 8 M, and 2 g/100 mL (1000):
(a) cross section and (b) side.
(a) (b)
Figure 5. SEM micrographs of composites under T 70 C, t 5 h, C 8 M, and 2 g/100 mL (1000):
(a) cross section and (b) side.
An optical graph of recovered glass fibers is given in Figure 6. The fibers are free from
residues and arranged in an orderly manner. A careful recycling process could eliminate
fiber damage and have a highly regular orientation.
Figures 7 and 8 show the electron probe microscopic analysis of virgin fibers and
recycled glass fibers after washing and drying separately. When compared with virgin
fibers, the surface of the recycled fibers was smooth and showed little contamination.
The glass fibers were recovered undamaged and were reusable.
recovered fibers available from all of the recycling processes (Table 1) were employed as
reinforcement to prepare new composites.
Table 2 presents the ILSS of new composites. The composites were prepared by using
recovered glass fibers as reinforcement or virgin fibers as reference. The recycled
unidirectional continuous fiber-reinforced composites showed a reduction of 4.7% in
ILSS and recycled short fiber-reinforced composites produced a strength reduction of
only 2.5%.
Knowing the wettability of fibers is useful to predict their adhesion potential to the
matrices. The contact angle of the fiber can characterize its wettability by the contacting
liquid in a given environment. Using glycol as a contacting liquid, the contact angle of
virgin fibers was 59.4 and that of recycled fibers was 56.1 . After oxidation of nitric acid
in the recycling process, the contact angles of the fibers decrease and their adhesion to the
matrices improves. It is likely that acid digestion increases surface roughness of the
ILSS (MPa)
fiber and improves interfacial bond strength, thus annulling the negative effects of
loss in tensile strength of the single fiber.
CONCLUSIONS
Recycling of thermoset epoxy composite containing glass fibers was studied and the
following results were obtained.
1. Concentrated sulfuric acid was not effective for decomposing glass/epoxy composites.
2. When the reaction temperature was 90 C, the concentration of the acid solution was
8 M, the feedstock ratio was 2 g/100 mL, and the reaction time was 5 h, the
decomposition rate of epoxy resin reached 99%.
3. The temperature and concentration of the decomposition solution were much more
effective than the feedstock ratio in increasing the decomposition rate of the resin
matrix.
4. Glass fibers from reinforced epoxy composites can be recovered undamaged without
any residue left. The recovered glass fibers have a tensile strength reduction of
3.515.1% under a set of decomposition conditions considered in this study.
5. Interlaminar shear strength (ILSS) of the recovered short fiber-reinforced composites
produced a strength reduction of only 2.5% compared with pristine composites.
ACKNOWLEDGMENTS
The authors gratefully acknowledge the financial support of the Study Abroad Returnee
Foundation of Hei Longjiang Province under Project No. LC03C09.
REFERENCES
1. Ralph, J., Graham, B. and David, W. (1991). Recycling SMC Scrap as a Reinforcement, Plastics
Engineering, 47(5): 1314.
2. Pannkoke, K., Oethe, M. and Busse, J. (1998). Efficient Prepreg Recycling at Low Temperatures, Cryogenics
(UK), 38(1): 155159.
3. Kouparitsas, C. E., Kartalis, C. N., Varelidis, P. C., Tsenoglou, C. J. and Papaspyrides, C. D. (2002).
Recycling of the Fibrous Fraction of Reinforced Thermoset Composites, Polymer Composites, 23(4):
682689.
4. Masatashi, I. (1998). Recycling of Epoxy Resin Compounds for Moulding Electronic Components, Journal
of Materials Science, 33(1): 4553.
5. Winter, H., Mostert, H. A. M., Smeets, P. J. H. M. and Paas, G. (1995). Recycling of Sheet-molding
Compounds by Chemical Routes, J. Appl. Polym. Sci., 57(11): 14091417.
6. Ushikoshi, K., Komatsu, N. and Sugino, M. (1995). Recycling of CFRP by Pyrolysis Method, J. Soc. Mater.
Sci., Jpn., 44(4): 428431.
7. Torres, A., De Marco, I., Caballero, B. M., Laresgoiti, M. F., Cabrero, M. A. and Chomon, M. J. (2001).
GC-MS Analysis of the Liquid Products Obtained in the Pyrolysis of Fibre-glass Polyester Sheet Moulding
Compound, Journal of Analytical and Applied Pyrolysis, 5859: 189203.
8. Jutte, R. B. and Graham, W. D. (1991). Recycling SMC Scrap as a Reinforcement, Plastics Engineering,
47(5): 1314.
9. Liu, Y. Y., Meng, L. H., Huang, Y. D. and Du, J. J. (2004). Recycling of Carbon/Epoxy Composites, Journal
of Applied Polymer Science, 95: 19121915.
10. Pickering, S. J., Kelly, R. M., Kennerley, J. R., Rudd, C. D. and Fenwick, N. J. (2000). Fluidized-bed Process
for the Recovery of Glass Fibres from Scrap Thermoset Composites, Composites Science and Technology,
60(4): 509523.
11. Liu, Y. Y., Meng, L. H., Huang, Y. D. and Liu, L. X. (2005). Study on Recycling of Glass Fiber/Epoxy
Composites through Solvent Method, Journal of Harbin Institute of Technology, 37(4): 470472.