Escolar Documentos
Profissional Documentos
Cultura Documentos
Products AB
SA.T.Training CAP540 091100 - 1
PST
PST
PST
From any terminal inserted in CAP 540 structure it is possible to
start the Parameter Setting Tool program.
For PST as well there is the possibility to run UPLOAD
OPTIONS, but it is called READ OPTIONS:
ABB Automation Technology
SA.T.Training CAP540 091100 - 2
Products AB
Possibilities from PST
TERMINAL OVERVIEW
From PST you can see which I/O cards are installed in the
terminal:
ABB Automation Technology
SA.T.Training CAP540 091100 - 3
Products AB
Possibilities from PST
SERVICE REPORT
From PST you can see the status of the output signals of each
function:
ZM1
ABB Automation Technology
SA.T.Training CAP540 091100 - 4
I/O Module 2
Products AB
Possibilities from PST
SERVICE REPORT
From PST you can see the status of the analog inputs of your
terminal:
Phasors / Secondary
ABB Automation Technology
SA.T.Training CAP540 091100 - 5
Products AB
Possibilities from PST
TERMINAL REPORT
From PST you can read the nominal values of CTs and VTs
installed in the terminal:
Analogue inputs
ABB Automation Technology
SA.T.Training CAP540 091100 - 6
Products AB
Possibilities from PST
CONFIGURATION
From PST you can read which I/O cards are installed and in
which slot they are positioned.
HW Slot
ABB Automation Technology
SA.T.Training CAP540 091100 - 7
Products AB
Possibilities from PST
CONFIGURATION
From PST you can read which menus in the HMI are disabled.
You can also decide which menus you want to enable/disable.
Built-in HMI /
SERVICE REPORT
ABB Automation Technology
SA.T.Training CAP540 091100 - 8
Products AB
Possibilities from PST
CONFIGURATION
From PST you can read and set the communication parameters:
Communication /
Front SPA Communication
ABB Automation Technology
SA.T.Training CAP540 091100 - 9
Products AB
Possibilities from PST
EVENT MASKS
From PST you can set the event masks for events to be sent to
Station Level:
EVENT MASKS /
Binary Events
ABB Automation Technology
SA.T.Training CAP540 091100 - 10
Products AB
Possibilities from PST
TEST
From PST you can set the behavior of TEST MODE for the
terminal:
ABB Automation Technology
SA.T.Training CAP540 091100 - 11
Products AB
Possibilities from PST
TEST
From PST you can set the
behavior of TEST MODE
for the terminal:
ABB Automation Technology
SA.T.Training CAP540 091100 - 12
Products AB
Possibilities from PST
SETTINGS
From PST you can set the functions installed in your terminal:
SETTINGS / ZM1
ABB Automation Technology
SA.T.Training CAP540 091100 - 13
Products AB
Possibilities from PST
SETTINGS
From PST you can set the all the four setting groups:
ABB Automation Technology
SA.T.Training CAP540 091100 - 14
Products AB
ABB Automation Technology
Products AB
SA.T.Training CAP540 091100 - 15 Hoe to read/write from terminal
Write to Terminal
Exercise 6
READ OPTIONS
1) Open your project from CAP 540, open PST for the terminal
where you have compared the configuration.
2) Navigate inside the PST structure:SETTING / Setting
Groups / Setting Group N / Phase and earth fault current
3) Click on TEF
4) You can define the settings for TEF but TEF is not installed in
the terminal!
5) Run Online / Read Options
6) You will have now the possibility to set only the functions
installed in your terminal.
ABB Automation Technology
SA.T.Training CAP540 091100 - 17
Products AB
Exercise 7