Escolar Documentos
Profissional Documentos
Cultura Documentos
DSL modem
wireless NIC
wireless router
Which type of frame contains information that is used in the election of the spanning tree root bridge?
2 BID
LSA
LSU
BPDU
Refer to the exhibit. The VTP domain has been configured as shown in the exhibit. None of the configured VLANs on SW1 and SW
present on SW3. What should be done to remedy the problem?
Reconfigure switches SW2 and SW3 in VTP transparent mode.
Reconfigure all switches as VTP clients to synchronize the VLAN database information.
Reconfigure the VTP server as a VTP client and then return to VTP server mode to reset the configuration revision number.
4
Refer to the exhibit. A network administrator needs to implement inter-VLAN routing on a hierarchical network. On which devices sh
the inter-VLAN routing be configured?
AS1 and AS2
5 Which two statements are correct about wireless infrastructure components? (Choose two.)
An AP converts the TCP/IP data packets from their 802.11 frame encapsulation format to the 802.3 Ethernet frame format on t
wired Ethernet network.
A wireless AP does not require any physical connection to allow wireless clients to access the Internet.
An AP is a layer 2 device, similar to a switch, that provides dedicated bandwidth to each connected wireless host.
Refer to the exhibit. What does “LEARNING” mean as it relates to the Spanning Tree Protocol?
The switch is sending and receiving data frames.
The switch is not receiving BPDUs, but is sending and receiving data.
The switch is participating in the election process by forwarding the BPDUs it receives.
The switch is receiving BPDUs and populating the MAC address table, but not sending data.
7 A network administrator needs to save the configuration file currently in RAM to NVRAM before rebooting the switch. Which comma
should the administrator issue?
Switch1# copy startup-config flash:filename
Refer to the exhibit. After entering the commands in the exhibit, the administrator receives a "password required, but none set" mes
when attempting to connect to S1. What is the problem?
The enable secret password was not set.
The VLAN1 interface has not be enabled with the no shutdown command.
Refer to the graphic. In the Wireless menu option of a Linksys integrated router, what does the Network Mode option Mixed mean?
The router supports encryption and authentication.
Refer to the exhibit. The switches are configured for VTP as shown. Which two statements correctly describe the operation of these
switches? (Choose two.)
A new VLAN can be added to Switch1 and that information will be added only to Switch2.
A new VLAN can be added to Switch1 and that information will be added to Switch2 and Switch4.
An existing VLAN can be deleted from Switch4 and that VLAN will be deleted from Switch1 and Switch2.
An existing VLAN can be deleted from Switch2 and that VLAN will be deleted from Switch1 and Switch4.
A new VLAN can be added to Switch4 and that information will be added to Switch1, Switch2, and Switch3.
A new VLAN can be added to Switch3 and that information will be added to Switch1, Switch2, and Switch4.
11
Refer to the exhibit. The switches have been configured as shown. The hosts that are connected to switch 101-2FL are not able to
communicate with the hosts in their corresponding VLANs that are connected to switch 101-3FL. What should be done to fix the
problem?
Configure port Fa0/2 on switch 101-3FL as a static trunk link.
Introduce a Layer 3 device or a switch with Layer 3 capability into the topology.
Utilize the switchport trunk allowed vlan all command on switch 101-3FL to permit the VLAN traffic.
Apply IP addresses that are in the same subnet to the interfaces that are used to connect switches 101-2FL and 101-3FL.
What is the correct order in which the STP components are chosen?
12 designated ports, nondesignated ports, root bridge, root ports
13
Refer to the exhibit. Both switches are configured with default bridge priority. Which port will act as the STP root port if all links are
operating at the same bandwidth?
Fa0/1 interface of S1
Fa0/2 interface of S1
Fa0/1 interface of S2
Fa0/2 interface of S2
What can an administrator do to ensure that a specific switch will win a root election if all switches are set to their default configurati
14 Set the bridge priority to 16384.
15 A network technician is evaluating the desirable features of both access and distribution layer switches. Which two features are com
to switches at these two layers? (Choose two.)
QoS
PoE
port security
link aggregation
application based filtering
16
Refer to the exhibit. After receiving a console notification on Switch2, the network administrator begins to troubleshoot the trunk link
between Switch1 and Switch2. Which configuration change can be made to correct the problem with the trunk link?
Set the Fa0/1 interface on Switch2 to trunk mode.
17
Refer to the exhibit. Router R-West and switch S-West1 are connected via a single ethernet cable between the router interface fa0/0
the switch interface fa0/1. The router and switch have been configured with the commands that are displayed in the exhibit. The netw
administrator enters the show interfaces trunk command and receives the output as shown. What is the cause of the "not-trunking"
status for switch port Fa0/1?
The trunk is established, but no VLANs have been configured to use it.
The router is missing the dynamic trunking protocol statements necessary to form a trunk.
Because the router does not support Dynamic Trunking Protocol, the trunk has not been established.
The router, the switch, or both must be configured with the dynamic desirable option for Dynamic Trunking Protocol to establis
trunk.
18
Refer to the exhibit. RTB is configured for traditional inter-VLAN routing. RTB can ping computer A but cannot ping computer B. Wha
possible cause of this failure?
Port Fa0/11 is in the wrong VLAN.
Router interface Fa0/1 has the wrong trunk encapsulation type configured.
19
Refer to the exhibit. The switch VTY lines have been properly configured, but PC1 is unable to remotely manage the switch. How can
problem be resolved?
Configure the Fa0/1 interface of the switch in trunk mode.
20 Which three statements are correct concerning the default configuration of a new switch? (Choose three.)
Spanning Tree Protocol is disabled.
21
Refer to the exhibit. Which two facts can be confirmed by this output? (Choose two.)
This switch shows no configuration revision errors.
This switch has established two-way communication with the neighboring devices.
This switch is configured to advertise its VLAN configuration to other VTP-enabled switches in the same VTP domain.
This switch will drop all VTP advertisements that come from the switches that are configured in the same VTP domain.
This switch will cause no disruption in the VTP domain operations if the rest of the switches in the same VTP domain have a h
configuration revision number.
It is calculated based on the utilization of all the switches along a given path.
It is calculated based on the bridge priority of the switches along a given path.
It is calculated based on the sum of the port cost value, determined by link speed, for each switch port along a given path.
23
Refer to the exhibit. A wireless infrastructure has been established in a company building as shown. The design goal was to allow
roaming between the three APs for handheld devices. However, the devices lose connectivity when the users roam. How can this
problem be fixed?
Assign different SSIDs to each AP.
Reposition the APs so that each area of signal strength overlaps the neighbor by at least 10-15%.
24 What VLANs are allowed across a trunk when the range of allowed VLANs is set to the default value?
All VLANs will be allowed across the trunk.
The switches will negotiate via VTP which VLANs to allow across the trunk.
25
Refer to the exhibit. A network administrator issues the command shown on Switch1. What are two possible reasons that ports Fa0
through Fa0/4, and ports Fa0/11 and Fa0/12 do not show in the command output? (Choose two.)
The ports have been configured as trunks.
The ports currently do not have any devices plugged into them.
26 A switch that is using port-based memory buffering receives two incoming frames on the same port. The destination port for the first
frame that is received is busy. How will the switch handle the second frame that it received?
The second frame will have to wait to be delivered even if its destination port is available.
The second frame will be delivered to the memory buffer for its destination port.
The second frame will be placed in a common memory buffer to await delivery.
27
Refer to the exhibit. The network administrator configures both switches as displayed. However, host C is unable to ping host D and
E is unable to ping host F. What action should the administrator take to enable this communication?
Include a router in the topology.
28
Refer to the exhibit. Router RA receives a packet with a source address of 192.168.1.35 and a destination address of 192.168.1.85
What will the router do with this packet?
The router will drop the packet.
The router will forward the packet out interface FastEthernet 0/1.1.
The router will forward the packet out interface FastEthernet 0/1.2.
The router will forward the packet out interface FastEthernet 0/1.3.
The router will forward the packet out interface FastEthernet 0/1.2 and interface FastEthernet 0/1.3.
SSID
ad hoc
channel
30
Refer to the exhibit. A new host needs to be connected to VLAN 20. Which IP address should be assigned to this new host?
172.16.10.68 /27
172.16.10.99 /28
172.16.10.110 /27
172.16.30.96 /27
172.16.30.120 /28
172.16.30.146 /27
31
Refer to the exhibit. Switch1 is configured for VTP as shown. An administrator connects four switches to Switch1 and configures tru
links between them. Which of the four switches will successfully receive and install VTP updates from Switch1?
What is the purpose of the switch command switchport access vlan 99?
32 to enable port security
33
Refer to the exhibit. What happens when a frame from a source MAC address different from 00a8.d2e4.ba27 reaches switch port 0
The frame is dropped.
When configuring a router to act as an SSH server, what should be configured before issuing the crypto key generate rsa comman
34 the security domain name
reduces administrative overhead by sharing VLAN databases between switches across the network
36
Refer to the exhibit. The switches in the exhibit have VTP pruning enabled. What will be pruned in the VTP advertisements from sw
ST-C to switch ST-1?
VLAN 30
37 A network administrator is implementing VTP in a large campus LAN that contains one hundred switches. What are valid considera
for reliability and administration?
Using server mode on a single master switch and client mode on all other switches will provide the most fault tolerance for reta
VLAN information in all switches if power is lost on the network.
Using transparent mode on all switches will allow for efficient administration and prevent VLAN data loss from the loss of any s
switch.
Configuring several switches in server mode will allow all VLANs to be entered from a single switch and preserve VLAN data if
of the switches or connections are lost.
Configuring one primary and one backup switch in server mode and all other switches in transparent mode will provide fault
tolerance for the VLAN data and allow for efficient distribution of the VLAN configurations to all switches.
38
Refer to the exhibit. An administrator documented the output of a CAM table from an Ethernet switch as shown. What action will the
switch take when it receives the frame shown at the bottom of the exhibit?
discard the frame
39
Refer to the exhibit. Hosts A and B attempt to transmit a frame at the same time and a collision occurs. When will host D be able to
transmit?
immediately
after the jam signal clears and its backoff delay expires
40
Refer to the exhibit. The commands are entered into switch SW1 as shown, and an 802.1q trunk is successfully established. How d
switch SW1 handle the untagged traffic that is destined for the trunk?
SW1 will drop all untagged traffic.
SW1 will send untagged traffic to all VLANs that are configured on the trunk.
41
Refer to the exhibit. Assuming the bridge priority values are set to default on all switches, which switch will be elected as the root br
of the spanning tree topology?
Cat-A
Cat-B
Cat-C
Cat-D
42
Refer to the exhibit. SW1 is a 2960 switch with default values assigned. Which two statements are true about what the cost value of
represents for SW1? (Choose two.)
SW1 connects via two FastEthernet links to reach the root switch.
The cost represents the numeric value for the fastest path from SW1 to the root switch.
A cost of 38 is the value that is being advertised out port 26 on the upstream switch, which is closer to the root switch.
SW1 adds the cost of a FastEthernet link to 38 to determine the total cost that is required to reach the root switch.
The root switch is advertising a cost of 38, which is lower than any other switch that participates in the VLAN0001 spanning-tre
domain.
SW1 connects via a FastEthernet link to an upstream switch that in turn is directly connected to the root switch via a Gigabit
Ethernet link.
43
Refer to the exhibit. Both switches are configured as displayed and the native VLAN is the default. Which statement is true about th
frames traveling between host A and host B?
They will travel untagged.
They will be tagged with VLAN ID 1.
Which three statements are correct regarding passwords configured on a switch? (Choose three.)
44 A different password can be set on each vty line.
The enable password is used if the enable secret password is not set.
The enable password command is more secure than the enable secret command.
The service password-encryption command is entered in global configuration mode and only encrypts global configuration m
passwords.
The service password-encryption command applies encryption to all passwords normally displayed in plain text by the show
running-config command.
45
Refer to the exhibit. Computer A sends a broadcast message. Which devices will see the broadcast?
computer B
Refer to the exhibit. The network administrator enters the configuration shown to allow both SSH and Telnet connections to the swit
The Telnet connections fail. What is the most likely cause of this problem?
The SSH version number is wrong.
47
Refer to the exhibit. What three statements describe why Host1 and Host2 are unable to communicate? (Choose three.)
The switch ports are on different VLANs.
The switch IP address is on the wrong subnet.
The host default gateway addresses must be on the same logical network.
flash
NVRAM
RAM
49
Refer to the exhibit. Which statement is true regarding the information shown?
Only one VLAN is currently configured to use the trunk links.
The switch negotiated trunk links for interfaces Fa0/1 and Gi0/1.
Interfaces Gi0/1 and Fa0/1 are allowed to carry data from multiple VLANs.
50
Refer to the exhibit. Switches SW3 and SW4 are brand new switches with default configurations. The links between the switches ar
configured as trunk links and all VLANs are allowed on the trunks. On the basis of the show running-config output that is provided
which VLANs will be available on SW3 and SW4?