Escolar Documentos
Profissional Documentos
Cultura Documentos
!~
llli.il_J
SPRINGER-SCIENCE+BUSINESS MEDIA, B.V.
First edition 1998
Ali rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted
in any form or by any means, electronic, mechanical, photocopying, record ing or otherwise, without the prior
written permission of the publishers. Applications for permission should be addressed to the rights manager at
the London address of the publisher.
The publisher makes no representation, express or implied, with regard to the accuracy of the information
contained in this book and cannot accept any legal responsibility or liability for any errors or omissions that
may be made.
A catalogue record for this book is available from the British Library
Within each major group the alloys can be divided into two Wrought Alloys
subgroups: heat-treatable and non heat-treatable alloys.
Commercial alloys are strengthened either by strain (work) As with cast aluminium alloys, commercial compositions fall
hardening or by heat treatment (age hardening); this can into a number of broad groups. This is again reflected in the
produce strengths in excess of 30 times that of pure, soft AA alloy designation system, which is now almost
aluminium. The degree of strengthening is known as universally used to describe these alloys - [See Alloy
condition or temper and is generally indicated by a suffix to Designation Systems]. Table 3 shows these compositional
the alloy code The most widely found system uses the categories.
following letters to indicate the nature of the treatment:
Composition Strengthening AA Alloys
D 0 = Annealed (soft)
CPAI >99% Not age hardenable 1xxx
D T = Heat-treated AI-Cu; AI-Cu-Li Age hardenable 2xxx
o H =Strain hardened AI-Mn Not age hardenable 3xxx
D F = As-finished (no specific treatment - the properties AI-Si; AI-Mg-Si Age hardenable (Mg) 4xxx
obtained depend on the forming method used) AI-Mg Not age hardenable 5xxx
Numbers following the T or H indicate the amount of strain AI-Mg-Si Age hardenable 6xxx
hardening and the exact type of heat treatment or other AI-Mg-Zn Age hardenable 7xxx
special aspects of the processing of the alloy. Variations
may exist within Nationally-based systems. [See: Alloy AI-Li, Sn, Zr, B, Mostly age hardenable 8xxx
Fe or Cu
Designation systems].
Table 3 - Aluminium Wrought Alloy Types
Casting Alloys
The 1xxx and 3xxx series are single-phase alloys, except for
Commercially available aluminium casting alloys fall into minor inclusions or intermetallic compounds. Their
several compositional groups. These groupings indicate properties are determined by strain hardening, limited solid
whether subsequent hardening heat treatments are solution strengthening and grain-Size control.
possible. As is shown in Table 2, they are also reflected in
the Aluminum Association codes for these alloys [See: Alloy The 2xxx, 6xxx, and 7xxx series are age-hardenable alloys
Designation Systems]. and can be heat treated to produce excellent strengths.
They cannot be used at temperatures above -175C in the
Composition Strengthening AA Alloys aged condition.
CPAI Not age hardenable 1xx 4xxx series are two phase alloys:
AI-Cu Age hardenable 2xx
AI-Si-Cu; AI-Mg-Si Some age hardenable 3xx D Alpha
AI-Si Not age hardenable 4xx D Beta - nearly pure silicon.
AI-Mg Not age hardenable 5xx The alloys containing both Si and Mg can be age-hardened
AI-Mg-Zn Age hardenable 7xx by precipitation of Mg2Si.
AI-Sn Age hardenable 8xx
5xxx alloys are two phase at RT:
Table 2 - Aluminium Casting Alloy Types
D Alpha, a solid solution of magnesium in aluminium,
The majority of commerCially used aluminium casting alloys o Mg2Ab, a hard, brittle intenmetallic compound.
come from the groups containing sufficient silicon to cause
the eutectic reaction. This gives alloys with particularly low AI-Mg alloys are strengthened by a fine dispersion of Mg2Ab
melting pOints, good fluidity (flow in the mould without as well as by strain hardening, solid solution strengthening
premature solidification), and good castability. and grain-size control. Age-hardening treatments are not
possible because the Mg2Ab is not coherent.
The properties of the AI-Si alloys are controlled by:
D solid solution strengthening of the alpha aluminium Aluminium-Lithium Alloys
matrix.
Alloys containing lithium have been introduced, particularly
D dispersion strengthening by the beta-phase. for the aerospace industry. As Li additions are lower than
D solidification characteristics (control of the primary grain the other main alloying elements they are dispersed
size, shape plus the nature of the eutectic amongst the 2xxx, 7xxx and 8xxx wrought aluminium series.
microconstituent).
Review 3
The addition of lithium can give significant improvements in strengthening is possible. However the solubility increases
mechanical properties, but may compromise other with temperature allowing many alloys to be strengthened
characteristics: by either dispersion strengthening or age hardening.
IJ The low density of lithium gives a reduction in alloy Age-hardened magnesium alloys (containing Zr, Th, Ag, or
density (can be 10% less). Ce) can have good resistance to over-ageing at
IJ Increased elastic moduli. temperatures as high as 300C.
IJ Strength equals or exceeds conventional alloys. Alloys containing up to 9% lithium have exceptionally low
IJ Improved fatigue resistance (slow fatigue crack growth densities.
rate). To improve the generally poor corrosion performance, some
IJ Good toughness at cryogenic temperatures. magnesium alloys have very low levels of impurities or
contain large amounts (>5%) of rare earth (RE) elements.
IJ Can be superplastically formed into complex shapes.
These alloys form a protective MgO film.
IJ Can be prone to stress corrosion cracking (SCC); varies
with other alloying elements and levels. The SCC Titanium Alloys
resistance can be improved by specific heat-treatments,
although the strength may be compromised. Titanium alloys have intermediate densities and temperature
The high specific strength and specific stiffness makes resistance, along with excellent corrosion resistance. They
these alloys useful for aerospace structural applications, are widely used for applications in aerospace and chemical
e.g. floors, skins, and frames in military and commercial processing. Many of the alloys show a powerful response to
aircraft. strengthening by age hardening and quench and temper
heat treatments.
The high strength of AI-Li alloys results from age-hardening.
Alloys containing up to 2.5% Li can be heat-treated by Titanium alloys have:
conventional methods. Additional Li (up to 4%) can be IJ high specific strength
introduced by rapid solidification processing; further
IJ high specific stiffness
enhancing light weight and maximum strength.
IJ good high-temperature properties
Magnesium Alloys LJ excellent resistance to corrosion and contamination
below 535C owing to an adherent, protective Ti02 film.
Magnesium is often extracted electrolytically from Above 535C, the oxide film breaks down and small
concentrated magnesium chloride in seawater. It melts at a atoms such as carbon, oxygen, nitrogen, and hydrogen
slightly lower temperature than aluminium. embrittle the metal.
IJ Good speCific strength. The excellent corrosion resistance provides applications in
U Corrosion resistance (many environments) similar to chemical processing equipment, marine components, and
aluminium. biomedical implants. It is an important aerospace material
and is used for airframe and jet engine components.
IJ Very low density.
IJ Very good casting characteristics.
Owing to its high affinity for oxygen and other gases, any
melting and casting processes must be carried out under
CJ Low modulus. vacuum.
::J Low level of strengthening mechanisms. Pure titanium is allotropic, with an HCP crystal structure
IJ Poor elevated temperature properties. (alpha) at low temperatures and a BCC structure (beta)
IJ Poor fatigue resistance. above 882C. Alloying elements provide solid solution
strengthening and change the allotropic transformation
IJ Poor creep resistance. temperature (alpha-beta transition) [See also: Effects of
IJ Poor wear resistance. Alloying Elements and Impurities]. The effects include
IJ Poor tolerance of salt-containing environments. IJ solid solution strengthening without affecting the
transformation temperature (Sn, Zr).
IJ Poses a hazard during casting and machining (combines
readily with oxygen and burns). IJ increase in alpha to beta transformation temperature by
alpha stabilising elements, (e.g. AI, 0, H).
Magnesium alloys are used in aerospace applications,
IJ decrease in transformation temperature; causing beta to
high-speed components, transportation and materials
handling equipment, portable equipment (mobile phones), be stable at RT, (beta stabilisers, e.g. V, Ta, Mo Nb).
car components. IJ providing a eutectoid reaction which gives a two-phase
alpha-beta structure at RT (Mn, Cr, Fe).
Structure and Properties
In addition to the range of commercially pure grades and
Pure magnesium is generally less ductile than aluminium, conventional alloys, specialist titanium-based materials
but this may be increased by alloying. Some deformation include:
and strain hardening is possible at room temperature, and IJ Titanium-Niobium - a superconductive intermetallic
the alloys can be readily deformed at elevated compound.
temperatures. Strain hardening produces a relatively small
effect in pure magnesium because of the low IJ Titanium-Nickel - shows a shape-memory effect.
strain-hardening coefficient. IJ Titanium-Aluminium intermetallics (titanium aluminides)
which are being considered for some applications
The solubility of alloying elements in magnesium at room requiring excellent high temperature characteristics;
temperature is limited; only a small degree of solid solution mainly aerospace related.
4 Review
Commercially Pure Titanium Highly alloyed alpha-beta alloys are age-hardened.
D Quenched - the beta phase is retained as beta ss
Applications include heat exchangers, piping, reactors,
(supersaturated in Ti).
pumps, and valves for the chemical and petrochemical
industries. IJ Ageing - the beta ss precipitates alpha (Widmanstatten
structure) which improves the strength and fracture
D Superior corrosion resistance.
toughness.
D Impurities, such as oxygen, increase the strength of the
titanium (but reduce corrosion resistance). Some typical applications for the heat-treated alpha-beta
alloys are aerospace components (airframes, rockets, jet
Alpha Titanium Alloys engines, landing gear). Some alloys, including Ti-6AI-4V,
can be superplastically formed.
This group commonly contain either 2.5% Cu or 5% AI +
2.5% Sn which provide solid solution strengthening to the Beta Titanium Alloys
alpha phase. Alpha alloys are annealed at high temperature
(beta), subsequent cooling determines the microstructure: None of the so-called beta alloys (usually containing V or
Mo additions) are entirely beta at RT. Instead, they are rich
D rapid cooling gives an acicular (Widmanstatten) alpha in beta stabilisers, such that rapid cooling produces a
grain structure with good fatigue resistance. metastable all-beta RT structure. Strengthening is obtained
D furnace cooling gives a plate-like alpha structure with both from:
improved creep resistance. o large amounts of solid-solution-strengthening alloying
Copper containing alloys may also show some precipitation elements.
hardening. o ageing the metastable beta structure to allow alpha to
precipitate.
Near-Alpha Alloys
Applications include high-strength fasteners, beams, and
A complex group of compositions where the microstructural other fittings for aerospace applications.
constituents are determined by heat treatment. Alloys may
be alpha or alpha + beta. Processing adjustments can be Beryllium Alloys
used to improve particular properties, e.g. high temperature
properties for engine applications. Beryllium has an exceptional strength-to-weight ratio,
maintains its strength at high temperatures and is very stiff.
Alpha-Beta Titanium Alloys Properties of commercial alloys are highly anisotropic.
A balance of alpha and beta stabilisers produces a mixture It is extracted from bertrandite (low-grade) and beryl (high
of alpha and beta phases at RT. The most alloy common of grade) ores by wet chemical techniques to give beryllium
this type is Ti-6AI-4V. Because the alloys contain two hydroxide. This is then converted into primary metallic
phases, heat treatments can be used to control and modify beryllium 'pebbles' by reduction using magnesium. These
the microstructure and properties. are then vacuum melted to form ingots which are
subsequently processed into pure (98-99%) powders.
Annealing provides a combination of high ductility, uniform
properties, and good strength. The cooling rate then These powders (BeQ <2%) are vacuum hot-pressed into
determines the final microstructure, and has different effects shapes and subsequently processed to semi-finished
on the two phases present: product forms. Recommended processing temperatures are
D Alpha: the alloy is heated just below the beta-transus 538-760C; below 371C brittleness is a problem.
temperature, permitting a small amount of alpha to The main characteristics of beryllium are:
remain and prevent grain growth:
o Lower density than aluminium.
Slow cooling causes equiaxed alpha grains to
form; good ductility and formability while inhibiting o Higher modulus (stiffer) than steel.
fatigue cracks from nucleating. o High speCific strength.
Faster cooling, particularly from above the alpha- o Low ductility (brittle).
beta transus temperature, produces an acicular or
'basket-weave' alpha phase. Fatigue cracks can
o Maintains both strength and stiffness to high
temperatures (>600C). Useful mechanical properties
nucleate more easily in this, but crack growth is
are retained at elevated temperature to >800C and
slower because of the complex structure (following
down to cryogenic temperatures.
the boundaries between alpha and beta phases);
good fracture toughness and creep resistance. o Transparency to electromagnetic radiation.
D Beta: two possible microstructures may be produced o Reactive.
when beta phase is quenched from high temperature: U Expensive.
Quenched - the beta transforms to titanium
martensite (alpha') in an alloy that crosses the Ms
o Beryllium oxide is toxic.
line on cooling. The titanium martensite is a Beryllium has an HCP crystal structure giving limited
relatively soft, supersaturated phase. ductility at room temperature. When exposed to the
Tempered - When alpha' is reheated beta is atmosphere at elevated temperatures, it rapidly oxidises to
precipitated from the supersaturated alpha' phase. form BeQ. These problems require the use of sophisticated
Fine beta precipitates initially increase the strength manufacturing techniques, such as vacuum casting, vacuum
compared with the alpha' (the opposite of a forging, and powder metallurgy. Consequently the majority
tempered steel martensite). Softening occurs when of beryllium components and structures are produced by
tempering is at too high a temperature. companies dedicated to working with the materials.
Review 5
Beryllium tends to be used for particular applications D Various protective coatings are possible to provide
exploiting a particular property rather than as a general protection in hostile environments:
engineering material, e.g.: Proprietary 'Beryl coat' passivation coating;
D High specific stiffness (inertial guidance systems), Chromate conversion for salt-spray and high
temperature oxidation resistance.
D Structural properties in weight-critical applications;
aerospace applications, e.g. windshield components on Anodising (chromic acid) - for corrosion protection,
the Space Shuttle, increase emissivity and reduce light reflection
(optical equipment).
D High-temperature stability, conductivity and low thermal
Plating - not widely used, except for electroless
expansion are attractive for use in space,
nickel plating (polished surface of beryllium
D Specialist uses (X-ray windows in medical and analytical mirrors).
equipment, nuclear industry: neutron reflectors and
D Recycling - Clean scrap is recycled into new products by
moderators, etc.).
the major producer.
Rigorous safety procedures are required when working with
beryllium to avoid inhalation of metal particles and Metal Matrix Composites (MMC's)
compounds, including the oxide, which are toxic,
Owing to the specialist uses of beryllium, material In MMC's a reinforcement phase is incorporated into a metal
speCifications, where they exist, tend to be defence alloy. The reinforcement phase may be a particulate,
standards, e.g. MIL-B-8964 Sheet & plate, MIL-B-21531 whisker or continuous fibre. The aim is to produce a material
Bar, rod & shape. which retains some of the characteristics of the matrix (such
as ductility, formability, etc,) but has improved properties
Forms and Processing Methods (such as strength and stiffness) provided by the
reinforcement. All light metals, with the exception of
D Forging - possible. beryllium, have been considered as matrix phases for
D Rolling - possible, MMC's. Many alloy variants have been investigated with the
aim of improving mechanical properties, thermal stability
D Extrusion - possible.
and wear characteristics A number of combinations are
D Drawing - possible. now commercially available and have found applications
D Sheet - (cross-rolled) poor short-transverse properties such as: engine components, pistons, braking system parts,
prevent forming at low temperatures. Processing is etc.
normally carried out between 700-730C; not >790C or In general the size of particulate used for MMC's is much
original properties will be affected. larger than that used in oxide dispersion strengthened
D Plate and foil - possible (ODS) alloys.
DWire - possible Characteristics and processing parameters are determined
D Machining - using carbide tools. Surface damage from mainly by:
machining operations (which act as stress-raisers in D Matrix alloy.
load-bearing parts) require removal by etching. Chemical
D Reinforcement content.
milling, electro-chemical machining and Electro-
discharge machining (EDM) avoid such mechanical D Chemical compatibility between a matrix and the
damage. Drilling may cause delamination and break-out reinforcement.
in sheet unless special precautions are taken, D Reinforcement/matrix bonding.
D Mechanical Joining - by rivets (squeeze-rivets only);
Manufacturing methods are usually adaptations of standard
bolting and threading. Press-fits need careful design to
metal processing techniques. These are generally powder
avoid damage.
metallurgical or casting in nature. Many of the techniques
D Brazing - with Zn-, AI-Si, Ag-based filler materials. Cu are patented and proprietary.
containing braze fillers may embrittle beryllium. SpeCial
techniques have been developed. Furnace brazing is Aluminium-based MMC's
done under vacuum to prevent oxidation. Dip-brazing is
also successful. Within the light-alloy matrix materials, aluminium-based
MMC's are probably the most advanced, The reinforcement
D Braze-welding - possible by TIG or MIG but requires a
is normally silicon carbide (particulate) for 'general
high level of welding skill. engineering' applications, with some continuous fibre-
D Diffusion bonding - possible reinforced MMC's for specialist aerospace applications.
D Soldering - possible. Aluminium-based MMC's are now used in load-bearing
applications in the aerospace, automotive and leisure
D Welding (fusion) - not recommended, owing to cast grain industries. Within the electronics industry, MMC's are finding
structure in weld-zone, applications in electronic packaging, Here, characteristics
D Electron beam welding - successful for applications such as combined high-thermal conductivity and low thermal
without structural requirements (instrument assemblies). expansion are of interest for thermal management uses
(mainly high-power circuits; GaAs microwave devices). In
D Adhesive bonding - with proper surface preparation (acid
general, the reinforcement content is higher than for
cleaning and neutralising), reliable bonds have been
engineering applications. Net-shape manufacturing, where
produced for spacecraft assemblies.
the MMC is formed at the same time as the product is useful
for intricate components.
6 Review
Magnesium-based MMC's Antimony - Sb
Those investigated so far use silicon carbide, alumina, Aluminium Alloys - can replace bismuth in some AI-Mg
alumina-silica or boron carbide particulate reinforcement. alloys to reduce hot cracking.
Some of these are of interest for automotive piston
applications because of their improved wear properties. Arsenic - As
Continuous fibre reinforcements have included carbon,
alumina, boron, silicon carbide and steel 'fibres'; with carbon Aluminium Alloys - highly toxic, must be strictly controlled
and silicon carbide fibres being the most promising options. to low limits in alloys for use in contact with food.
Aluminium Alloys - 2 to 10%. The formation of CuAb Titanium Alloys - beta stabiliser which tends to reduce
phase produces precipitation (age) hardening for both creep resistance.
wrought and cast alloys, one of the major hardening
combinations in heat-treatable aluminium alloys. Lead - Pb
Strengthening is at a maximum between 4 and 6%. Most
commercial alloys also contain other alloying elements to Aluminium Alloys - -0.5% improves machinability, but
improve properties. Improves strength at ambient and reduces ductility. Usually combined with a similar level of
elevated temperatures. Reduces corrosion resistance if bismuth. Tends to segregate during casting.
present above -0.2%. Binary AICu alloys are difficult to cast
because of the large solidification temperature range. The
basic alloying addition in series 2xxx wrought alloys and,
Lithium - Li
together With zinc and magnesium, some series 7xxx Aluminium Alloys - reduces density and increases elastic
wrought alloys. modulus. Up to 2.5% Li alloys can be heat treated by
Magnesium Alloys - generally controlled at low levels to conventional means, up to 4% Li alloys require rapid
avoid impairment of corrosion resistance. solidification processing (RSP). At impurity levels 5ppm)
may cause moisture corrosion problems in foils.
Titanium Alloys - 2 to 6%, beta stabiliser, alpha and beta
strengthener, provides precipitation hardening. Magnesium Alloys - (up to 9%) reduces density. In smaller
quantities, may improve corrosion resistance.
Germanium - Ge
Magnesium - Mg
Aluminium Alloys - increases strength and improves hot-
working properties of AICu alloys. Aluminium Alloys - can be used in combination with
silicon, copper or zinc to produce precipitation (age)
hardening. With manganese provides good work-hardening
Gallium - Ga characteristics. Additions of up to 1% improve the hot-
workability for extrusions and forgings and increases cold-
Aluminium Alloys - usually present as impurity at levels of
work strength. Increases the strength of 'pure' aluminium
0.001 to 0.02%. May affect corrosion/etching behaviour at (up to 3.5%). Improves corrosion properties, but increases
higher levels. In sacrificial anodes, 0.01 to 0.1 % prevents the tendency to pick up hydrogen. Alloys with up to 8% Mg
passivation. have very good corrosion resistance. AIMg binary alloys are
Magnesium Alloys - reported to markedly improve difficult to cast because of the large solidification
corrosion resistance. temperature range. Series 5000 wrought alloys and,
together with Si, series 6000 wrought alloys.
Titanium Alloys - alpha stabiliser.
8 Review
Manganese - Mn Oxygen - 0
Aluminium Alloys - grain refiner. Slightly increases Titanium Alloys - oxygen content is the main determinant
strength of 'pure' aluminium (up to 1.25%), but markedly of strength between the various commercial purity grades.
increases the alloy's ability to work harden. Gives a slight Strongly absorbed at temperatures >700C causing
decrease in corrosion resistance. In castings it can embritllement. Interstitial element which increases strength
compensate for some of the detrimental effects of iron. and reduces ductility, usually keep to a practical minimum.
Series 3000 wrought alloys. Alpha stabiliser. Some alloy grades use deliberate additions
of oxygen and iron as a strengthening mechanism. ELI
Magnesium Alloys - added to control iron content (1 to
(extra low interstitial) grades minimise N, 0 and H to
2%), should be at least 30 times the iron level. Improves improve fracture toughness.
corrosion resistance but has little effect on tensile strength.
May reduce fatigue strength. Beryllium Alloys - present as beryllium oxide (-0.5 to 4%)
in commercial alloys.
Titanium Alloys - 2 to 4%, no longer commercially
available.
Palladium - Pd
Molybdenum - Mo Titanium Alloys - additions of -0.2% Pd to commercial
purity grades significantly increases their corrosion
Titanium Alloys - 2 to 20% important beta phase stabiliser.
resistance in mildly reducing or fluctuating
Increases hardenability and short-term, high-temperature reducing/oxidising conditions.
strength. Reduces weldability and long-term, high-
temperature strength. Molybdenum (0.2 to 0.4%) in
conjunction with nickel (0.6 to 0.9%) improves the corrosion Rare Earths - RE
resistance of commercially pure alloys (lower cost
alternative to palladium containing alloys). Cerium, Lanthanum, Praseodymium and Neodymium
Aluminium Alloys - can improve high temperature
Nickel- Ni properties, fatigue strength and creep performance. In cast
alloys, may improve fluidity of melts and reduce die sticking.
Aluminium Alloys - can assist in precipitation (age)
Magnesium Alloys - important as grain refiners. Increase
hardening with the production of NiAb precipitates.
strength whilst retaining ductility and gives improved creep
Enhances high temperature properties, particularly in AI-Cu
resistance and fatigue strength. Improves castability and
and AI-Si alloys. Improves hot strength of castings.
reduces porosity (particularly Ce). Reduces cracking
Magnesium Alloys - very detrimental to the corrosion tendency in Mg-Zn-Zr alloys. All are highly soluble in molten
resistance of Mg alloys - controlled at very low levels (0.001 alloys and the concentration remains fairly stable throughout
- 0.002%) to avoid this. melting and handling operations.
Titanium Alloys - 0.6 to 0.9% in conjunction with
molybdenum 0.2 to 0.4% improves the corrosion resistance Silicon - Si
of commercially pure alloys (lower cost alternative to
palladium containing alloys). Aluminium Alloys - Improves fluidity and casting
properties, reduces the melting point. Can also be used in
precipitation (age) hardening with the production of Mg2Si
Niobium - Nb (Columbium - Cb, USA) preCipitates. May cause embrittlement in AICu alloys and a
grey colouration, especially on anodising.
Aluminium Alloys - up to -0.2% refines grain structure and
increases strength. Magnesium Alloys - highly soluble in molten alloys and the
concentration remains fairly stable throughout melting and
Titanium Alloys - beta stabiliser which also improves handling operations.
oxidation resistance at high temperatures.
Titanium Alloys - 0.05 to 1% improves creep resistance.
Nitrogen - N
Silver - Ag
Titanium Alloys - strongly absorbed (>800C) causing
embritllement. Interstitial element which increases strength Aluminium Alloys - 0.25 to 0.6% used in conjunction with
and reduces ductility, usually keep to a practical minimum. 2.5 to 5% Cu in some AI-Li wrought alloys and some casting
Alpha stabiliser. ELI (extra low interstitial) grades minimise alloys. 0.1 to 0.6% improves strength and stress corrosion
N, 0 and H to improve fracture toughness. Can be used in properties of AI-Zn-Mg alloys.
surface hardening (nitriding) treatments.
Magnesium Alloys - up to 3% provides precipitation
hardening of Mg-Zr-RE alloys to produce very high
strengths.
Sodium - Na
Aluminium Alloys - -0.01% used in "Modification"; the
refinement of the microstructure of cast near-eutectic (9 -
14%) silicon alloys. This increases strength and ductility.
Review 9
Strontium - Sr Zirconium - Zr
Aluminium Alloys - used in "Modification"; the refinement Aluminium Alloys - up to 0.5%. Inhibits recrystallization
of the microstructure of cast silicon alloys. This increases and controls grain structure. Used to retain fine grain
strength and ductility. structure in some superplastic alloys and reduce as-cast
grain size. May interfere with grain refining effect of
Thorium - Th titanium/boron.
Magnesium Alloys - usually up to 0.8%. Increases strength
Magnesium Alloys - up to 3%. Increases creep and fatigue through grain refinement. Improves high-temperature
strength at higher temperatures. Improves castability and strength. Provides precipitation hardening in conjunction
reduces porosity. Used with zinc and zirconium to restore with AI and Mn. Improves hot workability of wrought
weldability. Generally being phased out. materials.
Titanium Alloys - forms a continuous solid solution with
Tin - Sn titanium and increases strength at low to intermediate
temperatures. A weak beta phase stabiliser. If used above 5
Aluminium Alloys - a grain refiner. -0.05% can improve
- 6% it may reduce ductility and creep resistance.
the response of AI-Cu alloys to artificial ageing. Some
bearing alloys are based on AI-Sn with Cu, Ni and Si.
Titanium Alloys - 2 to 6%, less powerful alpha phase
ALLOY DESIGNATION SYSTEMS
stabiliser than AI, but is used in combination with this to
Until recently most countries used their own alloy
increase tensile strength while avoiding embrittlement. Also
designation systems, although several (i.e. those for
extensive solubility in beta phase. magnesium and wrought aluminium) were quite widely
understood and accepted throughout the world:
Titanium - Ti o Aluminum Association (AA) four-digit wrought aluminium
codes.
Aluminium Alloys - grain refiner for casting alloys, usually
in combination with boron. o Magnesium Elektron designations for magnesium alloys,
based largely on the ASTM system.
Vanadium - V o IMI designations for titanium alloys were internationally
accepted, as were the ASTM commercial purity grades.
Aluminium Alloys - in age-hardening casting alloys, V can
With the single European market came agreement that all
act as a grain refiner and improve the response of the alloy
material standards would be replaced by European
to heat treatment. Reduces electrical conductivity - can be
Standards and that national standards would be phased out.
controlled by addition of boron.
For light alloys this process is now well on the way to
Titanium Alloys - 2 to 20% beta phase stabiliser. completion in the countries of the European community.
So, currently the major USA and European designation
Yttrium - Y systems for light alloys are shown in Table 4.
Light alloys can be processed using the majority of In aluminium this produces small, rounded primary
traditional methods, e.g. casting (various techniques), aluminium grains surrounded by a eutectic microconstituent.
forging and mechanical methods (producing a wide variety The billet produced during this process is later reheated
of wrought forms). In some cases, special care is required to between the liquidus and eutectic temperatures to produce
avoid detrimental effects, e.g. oxygen pick-up and hydrogen a semi-solid material. When pressure is applied, this will
flow into a mould or die, producing a finished part with a
embrittiement in titanium; ignition during magnesium casting
or machining; explosive aluminium-water reaction during uniform microstructure and a minimum of casting defects.
casting; beryllium oxide exposure. These are well Automotive parts, including pistons and wheels, can be
produced by this method.
recognised and appropriate controlling methods are applied.
The traditional processing techniques are well described in Superplastic Forming (SPF)
many other sources [See: Further Reading] and will not be
described here. However, a number of methods have been Superplasticity can be achieved with most metals. The alloy
developed to improve properties, increase production rates is heated to around 50% of the melting temperature and
and reduce energy consumption. These newer methods can deformed at low strain rates up to many hundred percent
be particularly effective in increasing temperature strain. As essential characteristic of an SPF material is a
resistance. fine, uniform grain size with limited texturing. Whilst the
process is slow, complex, thin-walled shapes are possible
Rapid Solidification Processing (RSP) which would not be achievable by conventional forming
processes.
Molten alloy is broken into small droplets that solidify very
quickly to produce a powder. This is then processed using It has been applied successfully to some titanium and
standard powder metallurgical techniques. The rapid aluminium alloys to produce near-finished components.
solidification allows microstructural refinement not possible Titanium alloy SPF is often combined with diffusion bonding
by conventional methods. (DB) as a single process. This has produced complicated
In addition to property improvements in existing alloys, using integrally stiffened skin structures for aerospace
applications, e.g. Airbus fuselage inspection door. Diffusion
RSP, new alloys can be developed with compositions
bonding of aluminium is more complicated owing to the
beyond those normally possible (e.g. high lithium aluminium
tenacity of the oxide film (titanium absorbs its surface oxide
alloys). The effect can be achieved in several ways:
film at the processing temperature).
U atomisation.
Advantages include:
D splat cooling.
D simple forms of starting material (sheet, billet).
D melt-spinning.
D combined forming and joining (reduces cost, part counts
RSP provides: and subsequent machining or other operations).
D Smaller grain size (fast cooling). D useful for moderate production runs.
D Strengthening and toughening by microstructural grain
refinement. Powder Metallurgy (PM)
D Increases in possible alloy addition content (avoiding
segregation problems in ingots). Usually used for metals with high melting temperatures, PM
techniques can also be applied to light alloys to produce
D Fine dispersions of alloying elements. particular materials or avoid certain processing problems.
The technique has been applied to both aluminium and D Beryllium - standard production method for billet and
magnesium alloys: components to avoid oxygen contamination and BeO
D A group of aluminium alloys containing elements such as toxicity.
iron and chromium, present as intermetallic compounds D Aluminium and Magnesium - production of oxide
(dispersoids) e.g. AI6Fe. At room temperature the dispersion strengthened (ODS) alloys which contain a
properties of these alloys are similar to those of very fine (2-10nm), ceramic oxide content. ODS alloys
conventional ones. However, the dispersoids are stable have higher thermal stability and improved hardness
at higher temperatures, providing good properties where (wear resistance).
recrystallization or over-ageing would normally occur.
Potential applications include various structural
aerospace parts.
D AI-Li alloys containing >4% Li can be produced, giving
greater weight savings.
D For magnesium alloys, greater amounts of alloying
elements can be present in solid solution, further
improving corrosion resistance.
The term Rapid Solidification Processing is also applied to
some surface processing techniques involving very rapid
heating of a thin surface layer and subsequent rapid
quenching by the bulk of the material.
Review 13
FURTHER READING Metals Handbook
ASM International, 10th Edition, 1992
ISBN 0-87170-378-5
Books MIL-HDBK-5F: Metallic Materials & Elements for Aerospace
Vehicle Structures
Advanced Materials Department of Defense, USA (November 1990)
Enrico Pigorsch Contains design data for light-alloys.
Metra Martech Ltd, 7th Edition
ISBNIISSN 0-902231-79-0 Properties of Aluminium & its Alloys
Aluminium federation, UK 9th Edition, 1993
Aluminium Extrusions - a technical design guide
Shapemakers/Aluminium Extruders Assoc, UK, 1991 Registration Record of Aluminium Association Designation
& Chemical Composition Limits for Aluminium Alloy
Aluminium Standards & Data Castings & Ingots
Aluminium Association, USA, 1997 Aluminium Association, USA, 1996
American National Standard Alloy & Temper Designation Registration Record of Aluminium Association Designation
Systems for Aluminium & Chemical Composition Limits for Wrought Aluminium &
ANSI, 1993 (Metric) Available from Aluminium Association, USA
Aluminium Alloys
British & European Aluminium Casting Alloys - their Aluminium ASSOCiation, USA, 1997
properties & characteristics Science and Engineering of Materials
ALARS - Association of Light Alloy Refiners, 1992 D.R. Askeland
Available from Aluminium Federation, UK Chapman & Hall, 3rd Edition, 1996
ISBN/ISSN: 0-412-53910-1
Comparison of National Standards for Aluminium Casting
Alloys Smith ell's Metals Reference Book
OEA-Organisation of European Aluminium Smelters, 1996. Butterworth & Co. (Publishers) Ltd.
Available from Aluminium Federation, UK ISBN 0-408-71053-5
Dictionary of Scientific Units Structural Materials Handbook
H.G. Jerrard, D.B McNeill ESA PSS-03-203, ESA Publications, NL, 1994 (2-volume set).
Chapman & Hall, 6th Edition, 1992 Contains information on light alloy developments, MMC's, fibre
ISBN/ISSN: 0-412-46720-8 metal laminates; their design, fabrication & potential applications
in European aerospace projects.
Engineering Tables & Data
A.M. Howatson, P.G. Lund, J.D. Todd Tempers for Aluminium & Aluminium Alloy Products
Published by Chapman & Hall, 2nd Edition, Aluminium Association, USA, 1995
1991
ISBNIISSN: 0-412-38970-3 Metallurgy & Properties
Encyclopaedia of Materials Science & Engineering
Elsevier, 1986 (8-volume set) Advances in Corrosion Science & Technology
Plenum Press, USA, 1972
Encyclopaedia of Materials Science & Engineering
Supplementary Volume 3 Aluminium Alloys, Structures & Properties
L.F. Mondolfo
Ed. R.W Cahn/M.B. Bever
Butterworths, 1976
Elseveir, 1993 ISBN 0-08-040590-8
Third & last supplementary volume that continues the process of Aluminium & Aluminium Alloys: ASM SpeCiality Handbook
updating with important recent developments made in the field. ASM International, USA Available from Aluminium ASSOCiation,
Handbook of Composites USA
S Peters Aluminium Design Manual. Specifications & Guidelines for
Chapman & Hall, 2nd Edition
Aluminium Structures
ISBN/ISSN 0-412-54020-7
Aluminium ASSOCiation, USA, 1994
Includes Metal Matrix Composites
Aluminium: Properties & Physical Metallurgy
Handbook of Industrial Materials
ASM International, 1984. Available from Aluminium Association,
Ed. I. Purvis
USA
Elsevier, 2nd Edition 1992 ISBN: 0-946395-83-7
Updated to include recent major advances made in ceramics and Aluminium- Taschenbuch
polymer technology. An up-to-date source of information on Aluminium-Zentrale, Dusseldorf, D
industrial materials; for all industries.
Basic Corrosion Technology for Scientists & Engineers
Materials for Engineering Institute of Materials, UK, 2nd Edition
Institute of Materials, UK
Concise Inorganic Chemistry
Materials Selector J.D. Lee
Ed. NA Waterman & M.F. Ashby Blackie Academic & Professional. 5th Edition, 1997
Chapman & Hall, 2nd Edition, 1997 ISBN/ISSN 0-412-78820-9
ISBNIISSN 0-412-61550-9
Corrosion Atlas: A Collection of Illustrated Case Histories
Materials Selection Wallchart E.DD. During
M.F. Ashby Elsevier, 3rd Edition, 1997
Chapman & Hall, 1994 ISBN: 0-444-82616-5
ISBN/ISSN 0-412-61300-X Includes 679 case histories divided over 135 materials in 13
material groups, 25 systems (installations) and 44 different
Metallic Materials Specification Handbook phenomena. Case histories have been supplied by 20 companies
R. Ross and a number of private individuals.
Chapman & Hall, 4th Edition, 1992
ISBN/ISSN 0-412-36940-0
14 Review
Corrosion Control Introduction to Metallurgy
S. A. Bradford, Institute of Materials, UK, 2nd Edition
Chapman & Hall, 1993
ISBN/ISSN: 0-442-01088-5 Introduction to Powder Metallurgy
Institute of Materials, UK
Creep and Fracture of Engineering Materials & Structures
Institute of Materials, UK Light Alloys: Metallurgy of the Light Metals
I.J. Polmear
Creep in Metallic Materials Halsted Press, 3rd Edition, 1995
J. Cadek ISBN: 0470235659 (3rd Ed.)
Elsevier, 1988 ISBN: 0-444-98916-1 ISBN: 0340491752 (2nd Ed.)
Covers all aspects of high-temperature creep behaviour of metals
& alloys Magnesium Technology
Institute of Materials, UK
Cryochemical Technology of Advanced Materials
YO Tretyakov, OA Shlyakhtin, N.N. Oleynikov Materials Science
Chapman & Hall, 1998 J.C. Anderson et al
ISBN/ISSN: 0-412-63980-7 Chapman & Hall, 4th Edition, 1990
ISBN/ISSN: 0-412-34150-6
Databook on Fatigue Strength of Metallic Materials
Ed. K. Shiozawa & T. Sakai, Metal Matrix Composites
North-Holland (Elsevier), 1996 J.N. Fridlyander
ISBN 0-444-82514-2 (3-volume set) Chapman & Hall, 1995
Compilation of the experimental data on fatigue strength of ISBN/ISSN: 0-412-58260-0
various metallic materials and related information obtained over
the last 30 years by many researchers working in universities,
Metal Matrix Composites 4: Design & Innovation
Institute of Materials, UK
technical colleges, public research institutes and the technical
Materials Science and Technology Special Issue
laboratories of industrial companies in Japan; >3000 case studies
of S-N type fatigue data of ferrous and non ferrous metals Metal Matrix Composites. A study of patents, patent
Fatigue Data Book: Light Structural Alloys applications and other literature
Ed. S. D. Henry & F. Reidenbach (Editor) SA Gieskes, M. Terpstra
ASM International, 1995 Chapman & Hall, 1991
ISBN 0871705079 ISBN/ISSN: 1-85166-629-X
Titanium & Its Alloys: ASM Independent Study Course Building the Future: Innovation in design, materials &
International Titanium Association, USA construction
A course helpful in furthering the knowledge of personnel who are F.K. Garas, G.S.T. Armer, J.L. Clarke
engaged in production, fabrication and metallurgy, as well as E&FN Spon, 1994
technicians, designers, quality control personnel, salespersons ISBN/ISSN 0-419-18380-9
and purchasing agents who are users of titanium to make finished
parts. Construction Materials: their nature & behaviour
J.M. Iliston
Titanium: A Technical Guide E&FN Spon, 2nd Edition, 1994
Ed. M.J. Donachie, Jr., ISBNIISSN: 0-419-15470-1
A working guide to the field of titanium metallurgy. The
appendices provide a substantial source of information. Chapters Design for Aluminium: A Guide for Automotive Engineers
include Understanding the Metallurgy, Heat Treating, Machining, Aluminium Association, USA, 1980
Castings, Joining and the Relationships of Properties and Dubois and Pribble's Plastics Mold Engineering Handbook
Processes. E.L Buckleitner
Titanium the Choice ... Chapman & Hall, 5th Edition, 1995
International Titanium Association, USA ISBN/ISSN 0-412-98951-4
A basic primer about titanium. It covers physical metallurgy Guidelines for the Use of Aluminium with Food & Chemicals
considerations, alloy classifications, why titanium should be used,
Aluminium Association, USA
fabrications, and applications. Appendix 1 includes the physical
and mechanical properties of titanium grades currently in use. Guide to Specifications of Electrical installations Employing
Appendix 2 provides titanium corrosion rate data. Aluminium Conductors
Aluminium Association, USA, 1989
Titanium Technology. Present Status & Future Trends
Ed. F.H. Froes, Howard B. Bomberger & D. Eylon Light-weight Alloys for Aerospace Applications
A compendium of technical articles on the most recent Ed. EW. Lee
developments in titanium and titanium alloys technology. The Minerals Metals & Materials Society, 1991
introductory chapter offers a new historical perspective on the ISBN: 0873390946; 0873391357
metal and the industry.
Repair of Aluminium Automotive Sheet
Theory of Interaction of Metals & Alloys with a Corrosive Aluminium Association, USA, 1982
Environment
Cambridge International Science Publishing, UK Structural Failure: Technical, Legal & Insurance Aspects
H.P. Rossmanith
Applications & Usage E&FN Spon, 1996
ISBNIISSN 0-419-20710-4
Aerospace Materials and Structures
Institute of Materials, UK Processing
ISBN 1 861250495
Aluminium Casting Technology
Aluminium Alloy Structures Aluminium Association, USA, 2nd Edition, 1992
F. Mazzolani
E&FN Spon, 2nd Edition, 1995 Aluminium Extrusion Manual
ISBNIISSN 0-419-17770-1 Aluminium Association, USA, 2nd Edition, 1995
Aluminium for Automotive Body Sheet Panels Aluminium Forging Design Manual
Aluminium Association, USA, 1980 Aluminium Association, USA, 1995
Aluminium Building Wire Installation Manual & Design Guide Aluminium Impacts Design Manual & Applications Guide
Aluminium Association, USA, 1992 Aluminium Association, USA, 2nd Edition, 1988
Standards for Aluminium Sand & Permanent Mould Aluminium & Health: A Review of the Issues & the Efforts
Castings Aluminium Association, USA, 1996
Aluminium Association, USA, 1992
Guidelines for Handling Aluminium Fines Generated during
Superplastic Forming Various Aluminium Fabricating Operations
Ed. SP Agrawal
Aluminium Association, USA, 1992
ASM International, 1995
ISBN 0871701952 Guidelines for Handling Molten Aluminium
Aluminium Association, USA, 2nd Edition, 1990
Surface Treatment & Finishing of Aluminium & its Alloys (Spanish translation available)
Finishing Publications/ASM International, 1987. Available from
Aluminium Association, USA Recommendations For Storage & Handling Of Aluminium
Two-volume set Powder & Paste
Aluminium Association, USA, 1996
Joining
Safety, Health & Recycling Aspects Of Aluminium-Lithium
Aluminium Brazing Handbook Alloys
Aluminium Association, USA, 1990 Aluminium Association, USA, 1988
Key:
Product forms: P = powder.
= =
C cast; i ingot; c castings. =
= =
W wrought; r rolled product forms; e extrusions; d = =drawn products; b =billet;
f= forging-stock/forgings; w wire. =
Symbols: 0 =provide a number of alloys of a particular type;
= provide a wide range of those alloys;
=
MMC metal matrix composite;
FML = fibre-metal-laminate.
For aluminium wrought products CD 11) Q) @) I2l (j) indicates the international four-digit series for alloys.
=
Companies therefore offer one or more alloys within the stated series, e.g. I2l provides alloys from the
5xxx series.
Company Name [Product Forms1 Aluminium Magnesium Titanium Beryllium Composites Page
cast wrought powder cast wrought powder Number
AAA Weber
aalco - Slough (Stockist) [Wre[
[A/~
40
40
Aavid Thermal Technologies, Inc. ICc) MMC 40
The Aberly Group [Wb) 0 40
Advanced Metals Intemational fWd] 0 0 40
Aerodyne Ulbrich Alloys
Affibassin
[Wrdbw)
[C/]
40
40
Afficuivre [Gi] 41
Affimet - Aluminium Pechmey
Affinerie d'Anjou
[Gi]
[Gi]
41
41
Agents Aluminium Co Pvt Ltd
Airex AG
[Wr)
[W]
0
41
41
A.L. (Affinage de Lorraine)
Alba A/S
[Gi]
ICc)
41
42
Alcan Alluminio SpA - Bresso
Alcan Alluminio SpA - Borgofranco C'lvrea
[Wr)
[C) 0
42
42
Alcan Alluminio SpA - Pieve Emanuele
Alcan Deutschland GmbH & Co. - Berlin
[WreGi]
[Wr)
0
CJ
42
42
Alcan Deutschland GmbH - G6ttingen [Wre) 0 43
Alcan Deutschland GmbH - Nachterstedt [Wr) 0 43
Alcan Deutschland GmbH - Numberg ICc) 0 43
Alcan Deutschland GmbH - Plettenberg-Ohle [Wr) 0 43
Alcan France [We) 0 43
Alcan Lamines France SA [Wr) 0 43
Alcan Recycling [Wr) 0 44
Alcan Rolled Products UK - Falkirk [Wr) CDGl 44
Alcan Rolled Products UK - Rogerstone [Wr] CD@Gl@ 44
Alcan Rorschach AG [Wr) 0 44
Alcan Smelting & Power UK - Kinlochleven [C/] 0 44
Alcan Smelting & Power UK - Lochaber [Gi]
44
Baco Consumer Products
Baco Metal Centres [W] 57
P. Balloffet-Technicome [We] CDCl(l)@0 57
BDW GmbH & Ko KG [W] 0 57
57
Bemhard Metals (UK) Ltd. [CI] 0
Bibus Metals AG [CiWrdfw] 58
Bihar Extrusion Co Ltd [We] 0 58
Boal UK Ltd. [We] @ 58
Bright Metals [Wre] 0 58
British Aluminium Extrusions [We] CD0(l)ClJ@0 58
British Aluminium Plate [Wr] CDCl@0 59
British Aluminium Speciality Extrusions [CiWe] CDClG:l0 59
Manufacturers' Product Ranges 23
Company Name [Product Forms] Aluminium Magnesium Titanium Beryllium Composites Page
cast wrought powder cast wrought powder Number
British Aluminium Tubes Ltd. [Wed] (j)0~@0 59
British Aluminium Wire [Ww] (j)0~@0 60
Brillon, Ronald & Co. [P] 0
60
Brock Metal Company [GI] 60
Brush Wellman Ltd. - UK [Wrep] 61
Brush Wellman Inc. - Ohio [Wrep]
60
Gerard de Bruyn BV [-] 61
Bunting Titanium Ltd [Wrdbw] 61
Calder Aluminium - UK [Gi] 0 61
Capalex - Capital Aluminium Extrusions Ltd. [We] 0 61
Cardinal Aluminium Co. [We] 0 61
CFP - Cold Formed Products Ltd. [We~ 0 62
Chadwicks of Bury Ltd [Wr] 0 62
Chateauroux Fonderies [Ge] 0 62
CLAL-MSX [Wrw]
0 62
Goleshill Aluminium Ltd. [Gi] 62
Comalco Smelting [P] 0 62
Comeca [Wer] 0 0 0 62
Conalco - Consolidated Aluminium Corp. [Wr] 0 63
Creuzet, Robert Ets [We~ 00 0 MMC 63
CYCO International Ply Ltd. [-] MMC 63
D.B.S. Metals, Inc. 0
[W~ 63
Dead Sea Magnesium Ltd. - Be'er Sheva [Gi] 63/64
Deeside Aluminium Ltd. [Gib] 64
(j)~@
Deutsche Titan GmbH [GiWrdfbw] 64
D'Halluin, Georges Ets. [Wre] 72
(j)~
Fuchs, 0110 - Metallwerke GmbH [Wedfbw] CD0~@0 95
Garfield Alloys Inc. [GiP] 0 70
Gartner, Josef & Co [W] 0 88
Genecos SA [Wreb] (j)~ 70
General Extrusions, Inc [Wew] 0 70
Gleich GmbH [Wr] 0 0
71
Global Titanium Inc. [Wrp] 71
Glynwed Metal Services [Wre] (j)0~@ 71
GM Metal [GI] 0 71
Goodfellow Cambridge Ltd. [WP] 0 0 0 0 0 0 MMC 71
Gollschol Alucuilux SA [Gi] 0 72
Harvey Titanium Ltd.
Haynes Intema~onal
[Wred~
[Wd]
0
72
73
Heera Metals Ltd [Wre] 0 73
Heraeus Silica & Metals Ltd. [-] 0 73
High Duly Alloys - HDA Forgings Ltd. [W~ 0 0 0 MMC 73
High Performance Alloys, Inc. [-] 0 73
High Tech Tubes Ltd. [Wd] 0 0 73
Hitchiner Manufacturing Co., Inc. - Missouri [Ge] 0 MMC
74
Hoogovens Aluminium Espana SA - Madrid [Wr] 74
Hoogovens Aluminium GmbH - Koblenz [Wr] 74
CD0~@0
Hoogovens Aluminium Intemational NV [-] 75
Hoogovens Aluminium Metall GmbH
Hoogovens Aluminium NV - Duffel
[Gi]
[Wr]
75
75
Hoogovens Aluminium NV - Profiel Centrum [We] 0 75
24 Manufacturers' Product Ranges
Company Name [Product Forms] Aluminium Magnesium Titanium Beryllium Composites Page
cast wrought powder cast wrought powder Number
Hoogovens Aluminium NV - Sweden
Hoogovens Aluminium Portugal Lda,
[Wr]
[Wre] 75
75
Hoogovens Aluminium Profiltechnik GmbH [We] 75
Hoogovens Aluminium UK Ltd, - Birmingham [Wr]
76
Hoogovens Aluminium UK Ltd, - Herts, [Wre] 76
Hoogovens Aluminium USA Corp, [Wr] 76
Hoogovens Aluminium Waltzprodukte [We] 0 76
Hoogovens Aluminium Waltzprodukten - Koblenz [Wr] 76
Q)~0
Howmet Corporation [CieWfb] 77
Hydro Alluminio Atessa S,pA [CWeb] 0 0 77
Hydro Allunimio Omago SpA [CWeb] 0 0 78
Hydro Aluminio Portalex SA [We] 0 78
Hydro Aluminium A/S - AluCoat [Wr] 0 78
Hydro Aluminium A/S - Holmestrand Mill [Wr] CDQ)~ 79
Hydro Aluminium A/S - Karm0Y Mill [Wr] CDQ)~ 79
Hydro Aluminium Alupres Ltd, [We] 0 78
Hydro Aluminium Bellenberg GmbH [We] 0 79
Hydro Aluminium Century Ltd, - Co, Durham [We] 80
Hydro Aluminium Century Ltd, - Dumfriesshire [We] 79
Hydro Aluminium Chilteauroux s,n,c, [We] 0 80
Hydro Aluminium EXPA S,A (Remelt) - Belgium [CiWe] 0 80
Hydro Aluminium Extrusion Service - Lure [CWb] 0 0 80
Hydro Aluminium Fundo a,s [Ce] 0 81
Hydro Aluminium Metals Ltd, - Gwent [CWb] 0 81
Hydro Aluminium Nenzing GmbH - Austria [We] 0 81
Hydro Aluminium Profiler Karm0Y a,s [We] 0 82
Hydro Aluminium Profiler a,s - Raufoss [We] 0 82
Hydro Aluminium Raufoss Automotive [W] 0 82
Hydro Aluminium Raeren SA NV - Belgium [We] 0 82
Hydro Aluminium Rolled Products - Denmark [Wr] 0 82
Hydro Aluminium Rolled Products Ltd, - UK [Wr] CDQ)~ 83
Hydro Aluminium Seneffe SA - Belg ium [Wedw] 0 83
Hydro Aluminium Sverige AB [We] 0 83
Hydro Aluminium T0nder a,s, [We] 0 83
Hydro Aluminium Uphusen GmbH [We] 0 83
Hydro Estab, Manuel Ferreira, Lda, [We] 0 69
Hydro Alumino La Roca SA [We] 0 83
Hydro Fundo AB - Sweden [Ce] 0 70
Hydro Magnesium - Brussels [CiP] 0 84
Hydro Magnesium Norway - Porsgrunn [CiP] 0 85
Hyspeed Norway a,s [Ce] 0 85
Hyspeed S,p,a, - Venezia [Ce] 0 0 85
IMCO Recycling Inc, [C/] 0 0 85
INASA-Reynolds [We] 0 85
Indalex Ltd, [We] 0 85
INDAL -Indian Aluminium Company [Wre] 0 86
Indian Smelting & Refining Co, Ltd, [CI] 0 86
Inespal Laminacion SA [Wr] 0 86
Inometa France sarl [CeWed] 0 86
Interlink Metals & Chemicals [CiWr] 0 0 86
Intermetal SA (Compagnie des Metaux). CH [CiP] 0 0 87
Intermetaux SA - France [Wr] 0 87
International Extrusions [We] 0 87
Intexalu Systemes Puget SA [We] 87
0 87
Ireland Alloys Inc, [GI]
Itochu Non-Ferrous Materials Co" Ltd, [CiWrbw] 87
G, James Australia Ply, Ltd, [We] 0 87
Japan Metals & Chemicals Co, [CI] 0 88
Industrias R, Jimenez SA [C] 0 86
Kaye Aluminium pic [We] 88
Krupp Hoesch Steel Ltd,
Lachenallndustries
[CiW]
[Ce] 0 0
88
88
Lawson Mardon Star Ltd, [Wr] CDQ) 89
London & Scandinavian Metallurgical Co, Ltd [CiP] 0 MMC 89
Luxfer Gas Cylinders [We] 0 89
MagCorp - Magnesium Corp, of America [C11 90
Magnesium Elektron - UK [CiWrfbP] 0 0 MMC 90
Mark Metals Inc, [CieWrebw] 0 0 90
Marle [W~ 0 90
M & C Metaux et Chimie [P] 0 90
Metal Agencies Ltd, [Wr] 0 90
Metal Casting Technology. Inc, [Ce] MMC 91
Metallurg Inc, [CiP] 0 0 0 0 0 91
Manufacturers' Product Ranges 25
Company Name [Product Forms] Aluminium Magnesium Titanium Beryllium Composites Page
cast wrought powder cast wrought powder Number
Mifa Aluminium BV [We) (!)<l)@<J) 91
Mil-Ver Metal Co. Ltd. [Cll 0 91
Minalex [We] CD(!)<l)(j)@<J) 92
M. I. O.
Mitsui & Co. (USA) Inc.
[Wrdfbw)
[CiWrdfbwP)
92
92
Montangessellschaft GmbH [CiWe) 0 0 92
Morimura Brothers
FE Mottram (Non-Ferrous)Ltd.
[CiWrewP]
[GI]
0 92
92
National Northeast Corporation [We] 0 92
Nemco Metals International [Wr) 0 92
[Gil 0 93
Noranda Metallurgy Inc
Norsk Hydro Canada Inc. [CiP) 0 93
Norton Aluminium Products Ltd. [GI]
0
94
94
Nova Titanium Inc. [Wrdb]
94
Nuclear Metals, Inc. [CeWeP]
ORE MET Titanium [CieWbP] 94
Osprey Metals Ltd.
Palmex A.S.
[Pb]
[Wr) 0
0 94
95
Pandolfo Alluminio SRL - Italy [We) @<J) 95
Paramount Extrusions Co. [We) 0 95
[We] 0 96
Pechiney Aluminium Presswerk GmbH
Pechiney EleetrometallUigie (PEM) [CiP) 0 96
Pechiney Rhenalu d'Annecy [Wr] CD<l) 97
Pechiney Rhenalu - Bngnoud [Wr] 0 97
Pechiney Rhenalu - Issoire [Wred) CD(!)<l)@(j)@<J) 96
Pechiney Rhenalu - Neuf-Brisach [Wr) CD(!)<l)@(j)@<J) 97
Pechiney Rhenalu - Rugles [Wr) 0 97
Perfil Arteaga SA [We) 0 97
Phoenix [Wrdw) 0 98
PHP - Pechiney High Purity [CiWrw] 0 0 98
Pioneer Metals & Technology Inc. [P) 0 98
Plas-Met Chern Corporation [Wrew) 0 98
Plymouth Tube Company - USA [We) 0 98
Powder Alloy Corporation [P] 0 99
Productos Aluminio do Consumo SA (Alcan) [Wr) 0 99
Precision Extrusions Inc [We) 0 99
RADI - Reynolds Aluminium Deutschland Inc. [VV] 0 99
Raufoss A/S [P] 0 99
Raufoss Automotive AS [We) @<J) 99
Raufoss Automotive Skultuna AB - Sweden [We) 0 100
Raufoss Automotive (UK) Ltd. [We] @<J) 100
Razno Alloys Ltd. [Gil 0 100
Reade Manufacturing (Magnesium Elektron) [P] 0 100
REFINAL SA [Gil U 100
Reynolds Metals Co. (Bellwood) [Wr) 0 101
Reynolds Metals Company - Detroit [Wr] 0 101
Reynolds Metals Company - Detroit [We) 0 101
Reynolds International Service Company [CeWe) 0 100
Reynolds Metals Company - Richmond [Wr) CD<l)(j)@<J) 101
0 0 101
RIMA Industrial SA [CiP)
RMI Titanium Company [CiWrdb) 102
Rowan Cable Products Ltd. [Wwl CD@ 102
Sandvik Steel fWd) 0 102
Sandvik Special Metals Corp. fWd) 0 102
SAPA Aluminium France SNC [We) 0 103
SAPA Aluminium Profile GmbH [We) 0 103
SAPA A/S - Lillestrbm [We] 0 103
SAPA Ltd. - Derbyshire [Wre] @ 103
SAPA Poland Ltd [We] 0 103
SAPA - Skandinaviska Aluminium Profiler AB [We] 0 103
Saraf Metal Works [CiP] 0 104
Schreiber, Carl GmbH [Wr] CD(!)<l)(j)@<J) 61
SECO Aluminium Ltd. [We] @<J) 104
SENPOF Girebronze [VV] CD(!)(j)@ 0 104
Shen Wei East-West Trading Corp. Ltd. [Gil 0 104
SMG (Ste. Metallurgique de Gerzat) [Wed) 0 104
SOFAB [Ce] 0 105
Sofogir [Cl 0 105
Soltal [We] 0 105
SOGEM Iberica SA [Wre] 0 105
Solikamsk Magnesium Works [Gil 0 105
Soro Ltd. [Ww] CD(!)(j)@ 105
Spa Aluminium Ltd. [Wre] 0 105
26 Manufacturers' Product Ranges
Company Name [Product Forms] Aluminium Magnesium Titanium Beryllium Composites Page
cast wrought powder cast wrought powder Number
SpartalLtd [Wd] 0 105
Speciality Metals Company SA [CiP] 0 0 105
Spectrulite Consortium Inc.
Structural Laminates Co.
[CiWrefb]
[-)
0
FML
106
106
Sudallndustries Ltd. [We) 0 106
Suisman Titanium Conp. [CW] 0 106
Sumitomo Corporation of America [-) 0 106
Sumitomo Sitex Corp. [CiWP) 0 0 106
Superform Aluminium [W] CZlGl 106
Supra Alloys Inc.
TARAMMSA
[Wrdbw)
[Ce]
0
107
107
B.A. Taylor (Metals) Ltd
Technalloy SA [Wed)
[C/]
0
0
107
107
Technal Viking [We) 0 107
Tecla Industries [Ce] 0 107
Teledyne-Allvac - UK
Teledyne-Allvac - USA
[CiWb]
[CiWrdfbw)
108
108
Tepro Metall [Wr) 0 108
TERRA 4 Titanium Inc. [Wrdbfw) 0 109
Textron Systems - UK [-) MMC 109
Textron Systems - USA [-) MMC 109
Thyssen Garfield - Birmingham [W] 0 109
Tico Titanium, Inc. [Wrdbw) 0 110
TIMET - Denver
TI MET Castings Corporation
[CiWredbw]
[Ce]
110
110
TIMET Savoie
TIMET UK Ltd
[CiWredbw)
[CiWredbw]
110
111
Timminco Metals - Haley Plant
Timminco Metals - Toronto
[CiW]
[CiWeP]
0 0
111
111
Titania S.p.A. [Wrdbw] 0 111
Titanium Engineers, Inc. [Wdb] 0 111
0 112
Titanium Hearth Technologies, Inc. [CiWb)
Titanium Industries Inc. - New Jersey [Wrdbw] 112
[Wrdw] 0 113
Titanium International Fabricators (Pty) Ltd.
Titanium International Ltd. [CeWrdbw] 113
Titanium Powder Specialists, LLC [PI 0 113
Titanium Products, Inc. - Oregon [WfP) 0 113
0 113
Titanium Products Ltd. - UK [Wd]
Titanium Wire Corp. [Ww] 113
Toyal Europe SA [PI 0 113
Toyo Aluminium KK [P) 0 114
TYK Corporation [-I MMC 114
UBE Chemical Industries, Ltd. - Yamaguchi [Gi] 0 115
UBE Europe GmbH [Gi] 0 115
UBE Industries - Light Metal [CiP] () 115
United Alloys Inc. [Wrfb] 0 116
United Magnesium Company Ltd. [Gi] 0 116
[W] 0 0 () 0 116
Universal Stainless Inc.
Universal Steels & Aluminium Ltd. - Ayrshire
Universal Steels & Aluminium Ltd. - Lancashire [Wre)
[Wre)
116
116
US Vanadium Corporation [C] 0 0 116
UTSC [-) 0 116
[Gi] 0 116
Vanalp Industry
VAW AG - Bonn [Gi] 117
VAW Aluminium AG - Grevenbroich [Wr) CDQ)(\) 117
[Wr) 0 117
VAW France SA
VAW IMCO Gull und Recycling GmbH [Gi] 118
VI AM - All-Russian Institute of Aviation Materials [-I U 0 118
VIEXAL SA [Wr] 0 118
VILS [CiWrebfwP] 0 0 0 0 0 0 0 119
VSMPO [CiW] 0 0 119
Wah Chang [CiWredbfP] 0 119
Westinghouse Electric Corporation [P) 0 120
Williams Titanium Group [Ce] 0 120
Worcester Aluminium Alloys Ltd. [We] 0 120
Zamil Aluminium Industries [We) 0 120
Zinkal Ltd. [Web] 121
27
HIVOl (MMC)
ALCOA - Aluminium Company of America
VACONO (slugs)
28 Tradenames & Standard Product Codes
Dow ~R~e~y_n~o~ld~s~M~e~~~I~s_C~o~m~pa~n~y~_______________________
GROUP AFFILIATIONS
Including companies acting as agents and regional sales offices - sorted by country. The actual nature of the relationship is
often not clear from company literature.
AAA Weber [AI Mg Ti] S.A. Aciers Marathon Staal N.V. [ Ti]
~~~~~-=~~----------------~--~~
9 rue de Poitou, BP 3121 Emile de Harvenstraat 50-52
F-75121 Paris 3 B-271 0 Hoboken
France Belgium
Tel: +33 1 42 71 2345, Fax: +33 1 42 71 69 32, Contact Mr. Tel +32 3 8274091, Fax: +32 3 827 4095, Telex: 33672,
Bayard Group: Deutsche Titan (D)
Notes: Provide a very wide range of light-alloy products to Notes: Sales office (B) for Deutsche Titan (D)
customer requirements.
Baco Metal Centres (Dublin) Ltd. [ AI] Bernhard Metals (UK) Ltd. [AI]
Unit 500 Beech Road, Western Industrial Estate Litchurch Lane, Derby DE24 8AA
Naas Road, Dublin 12 United Kingdom
Ireland Tel: +44 1332279788, Fax +441332294308
Tel: +353 14602000, Fax: +353 14602150, Product Types: Cast alloys Ingots (to BS 1490). Hardeners.
Group: British Aluminium Holdings (UK) Other Services: Alloys to customer specifications.
Notes [Information provided by ALFED].
58 Supplier Addresses & Product Details
Bibus Metals AG [ Ti] BRASMAG [ Mg]
~H~e-rt~i-st~ra-s-s-e-1~~----------------------------~~~ Companhia Brasileira de Magnesio
CH-8304 Wallisellen Distrito Industrial de Bocaiuva
Switzerland CEP 39.391-000 - Bocaiuva/Minas Gerais
Tel: +4118775411, Fax: +41191822 56, Email: Brazil
bibus@access.ch, Internet: http://www.bibus.ch. Contact Felix Tel: +5538251 1100, Fax: +5538251 1598
Bibus - President Group: RIMA (Brasil)
Group: BIBUS Holding AG Est: 1979 Employees: 15
Associated Companies: Additional Sales Officers):
BIBUS Metals A-4812 Pinsdorf, Bright Metals [AI]
Tel: +43761271446, Fax +43761266398 13/1, Govt Place East
BIBUS Inco Alloys GmbH, D-40211 DUsseldorf Calcutta 700069
Tel: +49211 173140, Fax +49211 1731440 India
Product Types Wrought alloys Alloys, Forgings, Pipe - Welded, Tel: +91 33 2208601, Contact Mr G S Chopra - Partner
Strip, Bar & Rod, Ingot, Plate, Tube, Fasteners, Ingot - CP, Plate Group Bright Metals
- CP, Tube - Welded, Fittings, Pipe - Seamless, Sheet, Wire & Notes: Stockist & Consignment Agent of Indal. Dealer of:
Wire Coil, Flats, Ingot, Plate, Sheet, Bar, Tube, Wire, Aluminium Coils. Sheets. Foils. Corrugated Sheets. Chequered
Other Services: Cutting, Reforging, Cutting - Plasma, Sawing, Plates. ladders. Extrusions. Showroom: 85/b Colootolla St Cal-
Cutting - Waterjet, Shearing, laser Drilling & Cutting, Stock 73 TeI25-4188, 25-8238.
Holding
Notes: Distributor and stockholder of titanium (CP and alloys) and
nickel alloys with our own service center. British Alcan Aluminium pic [AI]
Chalfont Park, Gerrards Cross, Buckinghamshire Sl9 OOB
United Kingdom
Bihar Extrusion Co Ltd [AI] Tel: +44 1753233 200, Fax: +44 1753233 299
7, Lenin Sarani, 3rd Floor Group Alcan
Calcutta 700013 Associated Companies: World-wide: Europe (A, DK, SF, F, D, H,
India Eire, I, Nl, N, E, P, S, CH, UK)
Tel +91332280035,1256,1087, Fax +91332281036, Product Types: Wrought alloys Cast alloys Range of Alcan
Contact Mr Pankaj Shah - Managing Director products include: Foil, semi-rigid containers, packaging
Product Types: Wrought alloys, Extrusion. materials, automotive castings, extrusions, extruded
Notes Manufacturer of Aluminium Extrusions For Architectural, architectural & glazing systems. Alumina refining & alumina
Transport, Electrical and Other Allied Industries. chemicals.
Notes Wholly-owned subsiduary consisting of two main operating
companies: Alcan Aluminium UK Ltd. & Alcan Chemicals Ltd.
Blackwells [AI] Corporate Resource Group. Holding company & central
See: Anglo Blackwells Ltd services. Alcan's European operations include primary smelting
(UK), large rolling mills (plants in G, I, CH & UK), recycling &
secondary metal production.
Boal UK Ltd. [AI]
Ashby Road East, Shepshed
loughborough, leicestershire LE12 9BS British Aluminium Extrusions [AI]
United Kingdom Southam Road, Banbury, Oxfordshire OX16 7SN
Tel: +441509600012, Fax +441509507847, Contact: Mark United Kingdom
Rathjen - Technical Manager Tel: +44 1295454444, Fax +441295454674/4683, Contact:
Group: Boal Sales Office
Alloys: BOAl designations: AM62. AM65, AM68; AA Group British Aluminium Holdings (UK)
designations: 6060 to 6063, 6063A Tempers: F, F25, T4, T5, Alloys: Alloys 1XXX & 6XXX-series. [Standard extrusions alloys
T6. Designation systems CEN ISO BS 1050A, 1350, 2017A, 2024, 3003, 5083, 5754, 6005A, 6063,
Product Types Wrought alloys Extrusions in 6xxx series 6060, 6063A, 6082, 6101A, 7075]. Designation systems USA
aluminium: max. circumscribing circle 140mm, max. width CEN DIN NF.
120mm, max height 65mm, min wall 1.0mm, max. weight per Product Types: Wrought alloys Mill finish, painted & anodised
metre 3.5 kg/m, min. weight per metre 0 1 kg/m, min. cut length custom-design profiles. Max. circumscribed circle: 180mm, max.
0.7m, max cut length 8.0m. For products outside of these limits width 21 Omm, weight 0.08-4.00kg/m. Extrusion.
consult the Chief Engineer or Technical Manager. Applications Transport (wagons, body parts for drop-side,
Other Services Anodising, decorative anodising, painting, refridgerated & box vans, luggage rails, trim). Building (window &
polishing, chemical brightening. door frames, shop fronts & fittings, partitioning, greenhouse,
conservatory, roof structures, parapits, curtain walling).
Automotive. (sun-roof frames, roof-rails, structural & semi-
Brabant Alucast International BV [AI] structural components). Caravan & public service vehicles (door
Rijnstraat 19, Postbus 585 & window frames, exits, trim & body parts). MarinelOffshore
Nl-5340 AN Oss (helicopter deck & structure, stair-towers, walkways, fire-rated
Netherlands doors & windows, bridges, accomodation modules). Electrical.
Tel: +31412681444, Fax: +31 412681481 General Manufacturing, inc. ladders, stadium seating, road
Group: Hoogovens Groep signs, acces equipment.
Other Services: To customer specification In-house die making.
CAD/CAM systems. Approvals ISO 9002, CAA BCAR A8-4B2,
Brandau y Compania SA [AI Mg Ti] BAe. (ISO 9001, OS 9000 in progress), RG 2000.
Rafael Calvo 18-50, Apartado 6118 Notes: Over 60 years of extrusion experience. One of 3 BAI UK
E-28010 Madrid extrusion companies. Comprenesive range of solid, hollow &
Spain multi-hollow extrusions in a range of alloys (to international &
Tel: +34 1 419 1845, Fax +34 1 410 6909, Telex: 27485, customer-specification) .
Group: Metallurg (USA)
Product Types Powders
Supplier Addresses & Product Details 59
British Aluminium Ltd. [AIMg] British Aluminium Speciality Extrusions [ AI]
Head Quarters Lillyhall, Workington, Cumbria CA14 4JY
The Victoria, Harbour City United Kingdom
Salford Quays, Manchester M5 2SP Tel +44 190032 2500, Fax: +44 190032 2501, Contact Gregory
United Kingdom A. Davis - Export Sales
Tel: +44 161 911 8800, Fax: +44 161 911 8838, Contact Janet Group British Aluminium Holdings (UK)
McCook Alloys 1200, 1350A, 2014, 2014A, 2214, 2017, 2017A, 2024,
Group: British Aluminium Holdings (UK) 2025,2031,2618, 2618A, 4032, 5056A, 5083, 5086, 5154A,
Associated Companies: British Aluminium has sales agencies in 5251,5454,5754,6061,6063,6082, 6101A, 7010, 7014, 7017,
over 40 countries world-wide. Details available from any BAI site. 7019,7020,7022,7039, 7049A, 7050, 7075, 7150, 7175,7475,
Product Types: Wrought alloys, Plate, Sheet, Foil, Tube, Wire, 8090. Designation systems: USA CEN.
Extrusion. Product Types: Wrought alloys Cast alloys High- & medium-
Applications: All industry sectors, including general engineering, strength alloy extrusions in a wide range of alloys. Billet (cast &
aerospace & defence. machined): 190-51 Omm dia. (as-cast). Bar (round) max. dia
Notes: An international group of businesses that specialise in the 350mm for high-strength, 380mm for medium-strength. Bar
design, manufacture & supply of high-performance engineering (rectangular, hexagonal). Standard ( T, I, Z, top hat & channels)
materials, alloys & semi-fabricated components to the Hollows (seamless, porthole, single-&multi-hollow). Section &
manufacturing industry world-wide. profile dimensions: 360mm circumscribing circle (CCD),
rectangle 380x1 OOmm. Min. wall thickness >1.5mm (CCD/60).
Max soultion treated length 17m (20m for press water quench).
British Aluminium Plate [ AI] Billet, Bar, Extrusion, Forgings/Stock.
P.O. Box 383, Kitts Green Road Applications: Power (parts of turbines, nuclear industry).
Kitts Green, Birmingham B33 9QR Engineering (forge-stock bar). Transport (deck & hull contruction
United Kingdom of high-speed ferry). Construction. Aerospace (Airbus wing-
Tel: +44 121 252 8000, Fax: +44 121 252 800118010 stringer). Defence (bridges, armoured personnel carrier).
Group: British Aluminium Holdings (UK) Automotive (racing car pistons, motorcycle frames & arms).
Associated Companies: British Aluminium has sales agencies in Other Services Design. Custom-profles. R&D (alloys/new
over 40 countries world-wide. Details available from any BAI site. materials, processes, products). Heat-treatment,
USA: BA Plate (N. American distributor) SI. Louis, Missouri. homogenising/scalping billets. Controlled-stretch <330sqcm.
Alloys: Aerospace alloys: 2014A, 2214, 2618A, 2219 (V%05-.15), Approvals: BS EN ISO 9002. MoD, AQAP4, CAA, Qualifas,
2419 (V%.05-.15), 2024, 2124,6061,6082,7010,7050,7150, (Rolls-Royce, Boeing, Aerospatiale, Agusta).
7075,7175,7475,8090 (2.2-2.7&Li), BS L95. Tempers: TXX51 Notes: Large dimensional capacity. Approved suppliers for several
(stress relief/controlled stretch), TXX52 (on request). Defence major aerospace companies world-wide. Foundry, with latest
alloys 7017, 7018. 7019, 7020, 7039, 5083. Tempers: T7651 , degassing & filtration techniques. Extrusion presses (direct &
T651 , H115. General Engineering: 1050A, 1200, 5251, 5052, indirect) 1600T to 5000T Vertical & horizontal furnaces (solution
5454,5754,5086,5083, 2014A, 2017A,2024, 6061, 6082, treatment & aging). Largest European extrusion stretching
7020, 7075. Tooling: Alumec 79, Alumec 89. Tempers Fully facilities. Testing & inspection (NOT, mechanical &
treated, stress-relieved. Designation systems: USA CEN BS environmental testing).
DIN NF Defence. Customer
Product Types: Wrought alloys Strong alloy plate & cast forging
stock. Aerospace alloys, max. dimensions in TXX51 temper: British Aluminium Tubes Ltd. [ AI]
155mm thick, 3200mm wide, 16000mm long. Tolerances to Studley Road, Redditch, Wores. B98 7HN
aerospace specifications Tooling (Alumec) plate: 6.35-305mm United Kingdom
thick; round bar 200mm max. dia. Non-heat treated plate, Tel: +44 1527484500/4578, Fax: +44 1527 48 4502/4501,
stretched & heat-treated plate, stress relieved by controlled Contact John E. Blackham - Sales Manager
stretch: 6.35-200mm thick, 3200mm max. width, 16000mm max. Group British Aluminium Holdings (UK)
length. Non heat-treated plate, as-cast or part rolled, Associated Companies: British Aluminium has sales agencies in
unstretched: <305mm (max. width & length, on request). Heat- over 40 countries world-wide. Details available from any BAI site.
treated plate <305mm thick, <1200mm wide, <300mm long. Alloys Extruded & Drawn Tubes: 1050A, 1200, 1350, 2014A.
Tolerances to specified standards. Shipbuilding plate to 2017A, 2024, 3003, 5005, 5052, 5083, 5154, 5154A, 5251,
authorities regulations, e.g. Lloyds, DNV, etc. Pressure vessel 5754, 6005A, 6060, 6061, 6063A, 6063, 6070, 6082, 6101A,
plate to BS EN, ASME, TUV requirements. Plate. 6181, 7075. Process pipe: 5083, 5086, 5154, 5154A, 5454,
Applications: Aerospace (civil & military planes, inc. airframes, 6061,6063 Tempers: 0, F, H32, H12, H14, T6. Pneumatic
helicopter). Defence (armoured vehicles & portable bridge cylinders: 6063, (6061, 6082 + others on request). Tempers: T6
structures). Tooling (plastic mould tooling, inc. blow-mould tools, (BS), T832 (DIN), F22 (DIN), T7 (Alcan inhouse temper).
housings, technical mouldings for automotive, appliances, Designation systems USA BS DIN.
electronics industries). Engineering grades: road transport Product Types: Wrought alloys Seamless extruded & drawn
vehicles (bodies, tankers & trailers). Rail transport (mass- tubes in over 26 alloys. Products classed as Extruded seamless
transport, trams, hoppers). Marine (fast-ferries, work boats, (30-320mm 00, waI13-34mm). Extruded porthole (12-100mm
offhore rigs). Bulk storage (silos, static tanks, chemical & food 00, wall 1.2-12.5mm). Drawn seamless (5-550mm 00, 0.5-
plants). Electrical (busbar, heat-sinks). Industrial heat- 19mm wall) Drawn porthole (5-80mm 00, 0.5-11 mm
exchangers. wall) Tolerances to BS or customer requirements. Process pipe
Tradenames: Alumec Nominal bores & wall thicknesses to ANSI. Pneumatic:
Approvals. Various aerospace, marine & engineering body Extruded, then drawn to close-tolerance, cylindrical tube. Range
requirements. of standard sizes: 29mm 00, 25mm ID to 264mm 00, 250mm
Notes: Sole UK plate mill. Producing traditional alloy plate, AI-Li, ID. Tolerances to ISO 6537. Surface finish: anodized (15-25
aerospace alloys, mould & tooling plate. Armour plate. Export microns), non-anodized, scurfed, drawn-finish. Bore: anodized,
-50%. drawn, honed. Tube, Extrusion, Seamless (extruded or drawn).
Applications: Bus-bar, engineering components, structural
applications. Missiles. Sporting goods. Process pipework for
petrochemical industry, cryogenic & oil industry. Photocopier
drums. Pneumatic cylinder bodies.
Other Services: Fabrication, inc. machining, bending, welding.
Approvals BS 5750, ISO 9002, EN29002, MoD AQAP4, CAA.
Company approvals: Rolls-Royce, BAe, Westiands, BNF.
Notes: Extensive range of extruded & drawn tubes (seamless &
porthole). Direct & indirect extrusion techniques
60 Supplier Addresses & Product Details
British Aluminium Wire [ AI MMC ] Brush Wellman Inc. [Be]
~~~--~~--~~~~----~~~~----~
Port Tennant, Swansea, West Glamorgan SA 1 8PS Corporate Offices
United Kingdom 17876 St. Clair Avenue
Tel: +44 1792492400, Fax: +44 179249 2499, Telex 48191, Cleveland, Ohio 44110
Contact: Gareth Hyde - Sales Manager United States of America
Group: British Aluminium Holdings (UK) Tel: +1 2164864200, Fax +12163834091
Associated Companies: West Bromich (UK) Group: Brush Wellman (USA) Est: 1921
Alloys: 1050A, 1080A, 2011, 2014A, 2017, 2117, 2024, 3103, Associated Companies: Sales and technical services worldwide,
4043A, 4047A, 5052, 5056A, 5154A, 5183, 5251, 5356, 5554, including; Elmore, Ohio (USA); Reading, Pennsylvania (USA);
5556A, 5754, 6061, 6063, 6082, 7050, 7075. DIN AI99.5Ti. Delta, Utah (USA); Detroit, Michigan (USA); Los Angeles,
Tempers 0, M, H2, H4, H6, H8, TB, TF, TO, TH. Designation California (USA); Fairfiel, New Jersey (USA); Elmhurst, Illinois
systems: USA BS. (USA); Theale (UK); Stuttgart (D); Tokyo (J)
Product Types: Wrought alloys Aluminium wires, conductors & Alloys: "Pure Beryllium":- Powders: Vac. SP65, SP200F, IP-70.
strips. Drawn wires (to BS1475): 0.5mm-19mm dia. in various Hot pressed: S-65B, S200F, 1-70A, 1-220B, 1-400. Optical
tempers. Straight lengths 75-4000mm, close-straightness grades 1-70B, 1-220B, S-200F, 0-50. FoiIIF-1, PF-60. Flat rolled
control. Welding filler wire 0.8-6.0mm dia. 0.5kg, 6.5kg, 16kg grades SR200, PR200. HIP grades: S-200FH, 0-50, 1-250.
reels + TIG packs. Duralcan 90/10, an AI-1 0% alumina MMC Extruded: S-200.
wire, for wear-resistant coating, by flame- or arc-spraying. Beryllium Alloys:-
Coated tiles (300x300mm) available from Metallisation Services. AM162H (AI38-Be62), AIBeMet HIPped, rolled or extruded
Wire, Fastener stock. Product Types: Wrought alloys, Powders, Ingot, Billet, Plate,
Applications: Engineering (general machined components; Sheet, Strip, Foil, Bar, Tube, Extrusion, Near-net shapes &
fastener industry, inc. rivets for aerospace & automotive use; special processing routes.
nails for construction industry, roofing hooks; bolts for container- Applications Very wide ranging but specialised. Aerospace.
makers). Welding wire (MIG, TIG & Gas) Metal-spraying, arc- & satellites, defence, missiles, nuclear, radarlRF systems,
flame-spraying (anti-corrosion protection, wear & non-skid precision and micro-engineering, high stability optical systems,
coatings). Paper & film packaging. Zip-fastener manufacture mirrors, data storage systems, electronics.
Tea-bag staples. Electricity supply industries (BAI conductors). Tradenames: AIBeMet
Tradenames: Duralcan 90/10. Notes: Enquiries handled by Elmore Ohio division.
Other Services: To customer specification, inc. other alloys.
tolerances, shapes & strip. Approvals CAATUV (Wien), TUV
(Rhein-West), Lloyds ISO 9002, DNV, DB, ABS (USA). Brush Wellman Inc. [Be 1
Notes: Two UK manufacturing plants. Producing a wide range of 180 Passiac Avenue
wire products to meet customer requirements. Electrical wire Fairfield, New Jersey 07004
from British Aluminium Conductor (Swansea). United States of America
Tel: +1 201 2272552, Fax: +1 201 2272649
Group: Brush Wellman (USA)
Ronald Britton & Co. [AI] Product Types: Wrought alloys, Powders, Ingot, Billet, Plate,
Wallhead Mill, Kingsway, Rochdale, Lancashire OL 16 5AF Sheet, Strip, Foil, Bar, Tube, Extrusion, Fastener stock.
United Kingdom
Tel: +44 17064376112, Fax: +44 1706 42759, Telex: 63276
mknmet g, Contact: Elizabeth Lindley - Customer Services. Brush Wellman Inc. [Be 1
Group: Wolstenholme International Ltd. (UK) [Comalco] 18720 Crenshaw Blvd.
Product Types: Wrought alloys, Powders Aluminium (and many Torrence, CA 90504
other materials) powder and foil-flake products for decorative United States of America
purposes, glitters, reflective paints, metallic inks, etc., Foil, Tel: +13107152422, Fax: +13107152316
Shape foil flakes. Approvals: ISO 9002 Group Brush Wellman (USA)
Product Types: Wrought alloys, Powders, Ingot, Billet, Plate.
Sheet, Strip, Foil, Bar, Tube, Extrusion, Fastener stock.
The Brock Metal Company [AI] Notes: USA service centre.
Walsall Road, North Canes, Cannock, Staffordshire WS11 3NR
United Kingdom
Tel: +44 1543276666, Fax: +44 1543 276 418 Brush Wellman Inc. [Be 1
Product Types: Cast alloys, ingot. 27555 College Park Drive
Other Services: Technical support. Approvals: ISO 9002. Warren, Michigan 48093
Notes: Manufactures AI-alloy ingot to national specifications or to United States of America
customer requirements [Information from ALFED]. Tel: +18107722700, Fax: +18107722472
Group Brush Wellman (USA)
Product Types: Wrought alloys, Powders, Ingot, Billet, Plate,
Brush Wellman GmbH [Be] Sheet, Strip, Foil, Bar, Tube, Extrusion, Fastener stock.
Motorstrasse 34
0-70499 Stuttgart
Germany
Brush Wellman Inc. [Be 1
Tel: +49711 830930, Fax: +49 711 833822, Telex: 7252271, 606 Lamont Road, Elmhurst, Illinois 60126
Contart: Karl Ludwig Rausch United States of America
Group: Brush Wellman (USA) Est: 1981 Employees: 27 Tel: +1 6308329650, Fax: +1 6308329657
Product Types: Wrought alloys, Powders, Ingot, Billet, Plate, Group: Brush Wellman (USA)
Sheet, Strip, Foil, Tube, Extrusion. Product Types: Wrought alloys, Powders, Ingot, Billet, Plate,
Sheet, Strip, Foil, Bar, Tube, Extrusion, Fastener stock.
Dow Magnesium [ Mg] Drahtwerk Elisental - W. Erdmann GmbH & Co. [AI]
~~--~~~--~~~~~------------~~
Aurora Service Center, 3595 Moline Street PO Box 12 60
Aurora, Colorado 80010 D-58804 Neuenrade [Werdohler Str. 40, D-58809 Neuenrade]
United States of America Germany
Tel: (+1 8005257572), Internet http//www.dow.com Tel +49 23 92 697 0, Fax: +49 23 92 620 44, Telex 826452
Group: Dow Est 1919
Notes: Sales Office, Dow Magnesium. Associated Companies: UK Agent: Alcodan Metals Ltd
Alloys. DIN deSignations A199.999 to AI >99.9999, AI99.98R,
AI99.9, AI99.8, AI99.5, AI99.5TiO.6, E-AI, AI99.9Mg05,
Dow Magnesium [ Mg] AI99.9Mg1, AI99.9MgSi, AIFeSi, AIFeMg, AIMn1, AIMg1,
2020 Dow Center AIMg1.8, AIMg25, AIMg3, AIMg3.5, AIMg5, AIMg2MnO.3, E-
Midland, MI 48674 AIMgSi, AIMgSiO.5, AIMgSi1, AIMg1 SiCu, AICuBiPb,
United States of America AICu2.5MgO.5, AICuMg1, AICuMg2, AICuSiMn, AIZn4.5Mg1,
Tel: (+1 8004474369), Fax +1 5176389615, Internet AIZnMgCu1.5; Werkstoffe numbers 3.0385, 3.0305, 3.0285,
http//www.dow.com 3.0255, 30257, 3.3308, 3.3318, 3.3208, 3.0915, 3.0315, 3.3315,
Group: Dow Est: 1916 3.3326, 3.3523, 3.3535, 3.3555, 3.3526, 3.2305, 3.3206, 32315,
Associated Companies: World-wide. Dow European HQ in CH; 3.3211,31855,3.1305,3.1325,31355,3.1255,3.4335,3.4365;
Dow Pacific (area HQ) in Hong Kong. AA designations: 1090, 1080A, 1050A, 1350A, 6443, 8011 A,
Alloys ASTM designations AZCOML, AZ21X1, AZ31 B, AZ61A, 3103,5005, 5051A, 5052, 5754, 5154, 5056A, 5251, 6101A,
AZ80A, ZK60A, ZK40, AZ91B, AZ91D, AZ91E, AM60B, AS41B, 6060,6082,6061,2011,2117, 2017A, 2024, 2014, 7020, 7075.
AE42X1, AE42X2, 380 A1. Designation systems: USA. Tempers (AA) 0, H12, H14, H16, H18, T4, T6; (DIN) W7, W18,
Product Types Wrought alloys Cast alloys Pure & alloy primary F9, F10, F11, F13, F16, F19, F20, F21, F22, F24, F25, F26,
ingot. Secondary ingot. Sticks of various weights and forms. F27, F28, F30, F31, F32, F35, F36, F37, F38, F40, F43, F44,
Extruded anodes. Extrusion- & forging-billet. Chips & turnings. F46, F47, F50, F51, F52. Designation systems: USA CEN BS
Extrusions. Welding rod & electrode. Ingot, Billet, Bar, Tube. DIN NF
Wire, Extrusion, Forgings/Stock, Extruded anodes, welding rods. Product Types: Wrought alloys Round wire (0.1 to 18mm dia.),
Notes The Dow Group manufacture & supply a wide range of Flat wires (wide range of dimensions), Round & profile rods (1 to
alloys with various product shapes, sizes and uses. 15mm dia, up to 6m lengths). Custom alloys & products. Spools
& coils from 100g to 800kg. Wire, Fastener stock.
Applications: Fastener stock, packaging wire, metal spraying,
Dow Pacific [ Mg] vacuum metallization, bending, shaping & machining stock,
47E, Sun Hung Kai Centre, 30 Harbour Road, Wanchai welding wire & rod. Braid, mesh & woven material. Deep
Hong Kong drawing. Knitting needles, crochet hooks. Timber industry.
Tel: +852 879 7333, Internet: http//www.dow.com, Medical. Precision engineering. Cables. Staples.
Group Dow
DSM [ Mg]
Dow Quimica S.A. [ Mg] [See: Dead Sea Magnesium]
PO Box 9037
01065 Sao Paulo SP
Brazil Dufalco NV [AI]
Internet: http//wwwdow.com A. Stocletlaan 87
Group: Dow B-2570 Duffel
Belgium
Tel: +32 15 302111, Fax +32 15 302682
~wUU [~] Group: Hoogovens Groep
Suite 415, 8002 Discovery Drive Notes: Hoogovens Aluminium Rolled Products Duffel.
Richmond, VA 23288
United States of America
The Duriron Company [ Ti]
Tel +1 8042881601, Internet: http//www.dow.com
Group Dow Titanium Castings Operation, 2200 East Monument Ave.
Notes: Sales Office, Dow USA. Dayton, OH 45402
United States of America
Contact: Grant Felzien - Manager
Dow USA [Mg] Group: The Duriron Company Est: 1912 Employees: 3900
Suite 100, Detroit Dow Center, 26200 American Drive Associated Companies: Company Subsidiaries: Valtek, Atomac,
Southfield, MI48034 Automax, Durametallic.
United States of America Product Types: Cast alloys Alloys, Castings, Centrifugal Pumps,
Tel +1 3133581300, Internet: http//www.dow.com Commercial Products, Marine Hardware, Electrodes,
Group: Dow TiAluminide, Furnaces, Investment Castings, Furnaces, Vacuum
Notes: Sales Office, Dow USA. Induction, Ingot, Ingot, TiAluminide, Scrap - Buy & Sell.
Other Services: Engineering, Melting, Custom, Test, Toll
Processing
~wUU [~] Notes: Duriron's Titanium Castings Operation melts and pours
Suite 444, Great Northern Corp Ctr., 25000 Country Club Blvd. reactive alloys using its patented Induction Skull Melting (ISM)
North Olmsted, OH 44070 process. Titanium castings are the main products. Titanium
United States of America Aluminides and other reactive alloys are formulated and made
Tel: +1 2167348600, Internet: http//www.dow.com into castings, electrodes, and ingots.
Group: Dow
Notes Sales Office. Dow USA.
Supplier Addresses & Product Details 67
Dynamet Incorporated [ Ti] East-West Trading Corp. [ Mg]
195 Museum Road, Washington, PA 15301 See Shen Wei East-West Trading Corp. Ltd.
United States of America
Tel +1 412228 1000, Fax: +1 412 228 2087, Contact: Robert J.
Torcolini - President Eckart Switzerland [ Mg]
Group: Dynamet Inc. (USA) Est: 1967 Employees: 270 Zurcher Strasse 20
Associated Companies: Additional Sales Office(s) CH-4332 Stein (AG)
Dynamet Incorporated Switzerland
Stanton, CA United States of America Tel: +41 62 873 3264, Fax +41 62 873 1205, Contact: Mr.
Tel: +17148901410, Fax: +17148936291 Hermann Schillerwein
Alloys: All grades. Group: Shen Wei
Product Types: Wrought alloys All Titanium Grades, Bar & Rod, Product Types Cast alloys, Ingot.
Billet & Billet - CP, Medical, Rolled Shapes, Scrap, Turnings,
Wire & Wire Coil, Billet, Bar, Wire, Fastener stock.
Other Services: Applications Technology, Chemical Milling, Eckart-Werke [Mg]
Coatings 1Anodizing, Cold Finishing, Cold Working, Conversion Light Metal Div., Kaiserstrasse 30
Drawing, Grinding, Hot Working, Inspection, CMM, Research & D-90763 Furth
Design, Toll Processing, Wire Conversion. Germany
Notes: Dynamet Incorporated was founded to produce titanium Tel: +49 911 99780, Fax +49 911 99 78391, Contact: Mr. Gert
bar and wire for the aircraft specialty fastener industry. Other Rohrseitz
products include commercial and rotor quality bar, weld wire, Group: Eckart
fine wire, shapes, and metallurgical testing services. Dynamet Associated Companies Velden (D). st. Georgen (A).
serves customers on an international basis, concentrating on the Alloys: No details
aerospace, medical industries, and sports. Product Types: Powders Chips & turnings. Powder. Chunks &
granules.
Applications: Chemical industry. Pyrotechnics. Metallurgical.
Dynamet Technology Inc. [Ti MMC] Decorative/paints.
Eight A Street, Burlington, MA 01803 Notes: Provide an wide range of Mg powders, granules & turnings
United States of America to recognised standards or to customer requirements. Details
Tel +16172725967, Fax: +16172294879, Contact: Stanley provided by International Magnesium Association.
Abkowitz - President
Est: 1972 Employees 15
Product Types: Wrought alloys, Powders Automotive, Medical, Ecumet (UK) Ltd. [ Mg]
Bar, Hollow, Pipe, Seamless, Clad Products, Plate - Clad, 6 Paddockhall Road, Haywards Heath, West Sussex RH16 1HH
Commercial Products, Marine Hardware, Powder, Commercial United Kingdom
Products, Sporting Goods, Powder - High Purity, Composites, Tel: +44 1441 4952, Fax +441441 4958, Contact: Mr. Ron Wafer
Powder - Low Chloride, Extrusions & Extruded Shapes, Powder, Group: Shen Wei
Parts, Filters, Tanks & Vessels, Fittings, Tube, Ingot, Product Types: Cast alloys, Ingot.
TiAluminide, Plate, Sheet, Bar, Tube, Extrusion.
Tradenames: Cermeti
Other Services: Alloy Development, Hot Isostatic Pressing (HIP), Egyptian Aluminium Products Co. [AI]
Applications Technology, Research & Design, Cold Working, See: Alumisr
Toll Processing, Cold Isostatic Pressing (CIP).
Notes: Manufactures near-net shape components of advanced
materials by cold isostatic pressing of blended elemental Ekonal Bausysteme GmbH & Co. KG [AI]
powders. Specializing in titanium alloys and titanium matrix Velbert
composites (Cermeti) Dynamet Technology's materials and Germany
processes offer cost savings over conventional manufacturing Group Erbsloh AG
methods and enhanced mechanical properties. Product Types: Wrought alloys, Extrusion.
Applications: Architectural (window & fayade).
Heat Transfer Tlimder a.s [AI] High Tech Tubes Ltd. [AI Ti]
Hydrovej 6, PO Box 50 Industrial Estate, Monavalley, Tralee, Co. Kerry
DK-6270 T0nder Ireland
Denmark Tel: +3536634232, Fax +3536634314
Tel: +457472 03 04, Fax: +45 74 72 33 13 Group: High Tech Tubes
Group: Norsk Hydro Associated Companies: Byfleet, Surrey (UK).
Tradenames: HYCOT (nylon coated aluminium tubes) Alloys: See: High Tech Tubes Ltd. Byfleet, Surrey UK.
Notes: Heat-transfer parts found in air conditioning tubing, fluid Product Types: Wrought alloys small dia, thin-walled, tube.
return lines, radiator cores, manifolds for condensers, air-
conditoning compressors. HYCOT (nylon coated aluminium
tubes) autornotive fuel- & break-lines. High Tech Tubes Ltd. [AI Ti]
Unit 15F, Wintersells Business Park
Heera Metals Ltd [ AI] Wintersells Road, Byfleet, Surrey KT14 7LF
United Kingdom
79&80 Colootola Street, Calcutta 700073 Tel +44 1932 355440, Fax: +44 1932 355441, Contact: Mr. Jim
India Whiteley - Director
Tel: +91 33254667, Fax +91 332157555, Contact: Mr Vikram Group: High Tech Tubes
Jhunjhunwala Associated Companies: Co. Kerry (Ireland)
Product Types Wrought alloys, Plate, Sheet, Extrusion. Alloys Aluminium: 1050A, 5251, 5154A, 5083, 2014A, 3003.
Notes: Deals in: Aluminium Extruded Sections, Corrugated 6063. Titanium ASTM Grade 2 DeSignation systems: USA BS
Sheets, Coils, Plain Sheets, Chequered Plate, Pattern Sheet, DIN NF.
Closure, etc. Product Types: Wrought alloys Seamless drawn tubes of small
diameter & thin wall: OAmm OD, wall OAmm to 9.5mm dia.
Hellenic Aluminium Industry SA [ AI] 0.8mm OD. Tube, searnless, small dia. thin wall.
Other Services: Custom sizes/tolerances. Other alloys on
See: Elval - Hellenic Aluminium Industry SA request
Notes: Specialist producer of small diameter, thin walled tubes in
Heraeus Silica & Metals Ltd. [ Be] AI-alloys, Ti-alloy + Ni-, Cu-based alloys & Stainless Steel.
Drawing facilities to meet customer requirements Certification to
1 Craven Court
BS, DIN, ASTM, etc.
Canada Road
Byfleet
Essex KT14 7JL Hitchiner Manufacturing Co. Inc. [AIMMC]
United Kingdom Milford, New Hampshire 03055
Tel: +44 1932349315, Contact: Rex Old ridge United States of America
Notes Late entry. Tel +1 6036731100, Fax +16036737960
Group: Hitchiner Manufacturing Co. Inc. Est: 1946 Employees:
High Duty Alloys - HDA Forgings Ltd. [ AI Mg Ti MMC ] 2000
Associated Companies: Hitchiner SA de CV - Mexico
Windsor Road, Redditch, Worcestershire B97 6EF
United Kingdom
Tel +44 152764211, Fax: +44 1527 591760
Alloys AI-alloys (Hiduminium Alloy Number): HDA 66, HDA 75,
HDA 77, HDA 81, HDA 89. BS: 2L77, L 103, L161, L 162, DTD
6094A, DTD 51 04A. EN2382, EN2383, EN2486, EN2688, EN
2690, EN2681, EN2682, EN2683, EN2685, EN2686, EN2380,
EN 2386, EN2488. AA 2014A, 2214, 7050, 7014, 7010, 7075,
7175. Aluminium-Lithium: 8090, 8091,Titanium: Ti6AI4V. BS
2TA 13, EN2531; AMS 4928L, AMS 4967E. Magnesium:
MgZn302r06, BS L514. BS3372-MAGF-151 M. AECMA:
MGP43. Designation systems: USA CEN BS Proprietory.
Aerospace.
74 Supplier Addresses' & Product Details
Hitchiner Manufacturing Co. Inc. [AI MMC] Hoogovens Aluminium Espana S.A. [AI]
Nonferrous Division, O'Fallon, Missouri 63366 Avenida Puerta del Angel 40
United States of America E-08002 Barcelona
Tel: +1 3142726176, Fax: +1 314272 6180 Spain
Group: Hitchiner Manufacturing Co. Inc. Est: 1969 Tel: +3433186998, Fax: +3433021160
Alloys: Metal Matrix Composites - aluminum alloys with up to 40 Group: Hoogovens Groep
percent silicon carbide reinforcement using countergravity Notes: Hoogovens Aluminium Distribution and Service Centre.
investment casting
Product Types: Cast alloys Aluminium alloy castings and Metal
Matrix Composites Hoogovens Aluminium Espana S.A. [AI]
Applications: Aircraft, helicopter, satellite, spacecraft and Monte Esquinza, 44-1
missiles. Castings for advanced automotive applications. such E-28010 Madrid
as electric cars and electronic fuel-injected motorcycles. Spain
Notes: Specializes in producing complex, thin-walled Tel: +34 1 3196781, Fax +34 1 30821 58
configurations in aluminum alloys and MMC's. Group: Hoogovens Groep
Product Types: Wrought alloys
Notes: Sales for Hoogovens Aluminium Waltzprodukte - Koblenz.
Hogstad Aluminium AB [ AI]
Box 245, S-595 23 Mjalby
Sweden Hoogovens Aluminium Europe SrI. [AI]
Tel: +46 142 18900, Fax +4614219290 Via F. Russoli 1
Group SAPA 1-20143 Milan
Product Types: Wrought alloys, Extrusion. Italy
Notes Independent company within Sapa group - produces Tel: +392891 20333, Fax +392891 21395
window and architectural systems using Sapa extrusions. Group: Hoogovens Groep
Notes: Hoogovens Aluminium Distribution and Service Centre &
Sales for Hoogovens Aluminium Waltzprodukte - Koblenz (D).
Hoogovens Aluminium - Sidal GmbH [ AI]
Postfach 12 01 65
D-46101 Oberhausen [Fahnhorststrar..e 3, 0-46117 Oberhausen] Hoogovens Aluminium France SA [ AI]
Germany 2, blvd. Georges Clemenceau, BP 65
Tel +49 208 69 03 0, Fax: +49 208 69 03 111, Contact: Wolfgang F-92404 Courbevoie Cedex
Brauer France
Group: Hoogovens Groep Est: 1970 Employees: 67 Tel: +33 1 4667 10 70, Fax: +33 1 4667 10 79, 80, Telex
Notes Hoogovens Aluminium Distribution & Service Centre. 630822, Contact: Denis Clichet
Group: Hoogovens Groep
Notes: Hoogovens Aluminium Distribution & Service Centre.
Hoogovens Aluminium Bausysteme GmbH [AI]
Posffach 10 03 31
D-56033 Koblenz Hoogovens Aluminium GmbH [ AI]
Germany Carl-Spaeterstrar..e 10, Posffach 920
Tel: +49261 8910, Fax: +49261 82038 D-56070 Koblenz
Group Hoogovens Groep Germany
Notes: Hoogovens Aluminium Building Systems. Tel: +49 2618910, Fax: +49 261891342, Telex: 86253559
Group: Hoogovens Groep
Alloys: AA grades. 1050, 1050A, 1070, 1070A, 1200, 1350, 3103,
Hoogovens Aluminium Building Systems Ltd. [AI] 3003, 3003 Alclad, 3005 Alclad, 3004, 3004 Alclad, 5005, 5052,
Haydock Lane, Haydock, SI. Helens, Merseyside WA11 9TY 5454,5086,5083,6063,6061,2017, 2017A, 2024, 2014, 7075,
United Kingdom 7079. Hoogovens AI designations: 1070, 1000, 1001, 1010,
Tel +44 1942272152, Fax +441942272136 3000, 3000 plaque, 3530, 3530 plaque, 3560 plaque, 3540,
Group: Hoogovens Groep 3540 plaque, 3541, 5010, 5020, 3010, 5520, 5030, 5400, 5503,
Notes: Hoogovens Aluminium Building Systems. 5510,6630 plaque, 6010, 6560, 2170, 2240, 2140, 7350, 7750,
7790; DIN: AI99.7, AI99.5, E-AI, A199, AIMn1, AIMn1 plaque,
AIMnCu, AIMnCu plaque, AIMn1 MgO.5 plaque, AIMn1Mg1,
Hoogovens Aluminium Building Systems NV [ AI] AIMn1Mg1 plaque, AIMn1Mg1, AIMg1, AiMg1.8, AIMg2MnO.8,
A. Stocletlaan 87 AIMg2.5, AIMg3, AIMg2.7Mn, AIMg4Mn, AIMg4.5Mn, AIMgSiO.5
B-2570 Duffel plaque, AIMgSi1, AIMg1 SiCu, AICuMg1, AICuMg2, AICuSiMn,
Belgium AIZn4.5Mg1, AIZnMgCu1 .5, AIZnMgCuO.5; Wk. Numbers:
Tel +32 15302111, Fax: +32 15302920 3.0275,3.0255,3.0257,3.0205,3.0515,3.0517, 3.0525, 3.0526,
Group: Hoogovens Groep 3.0526, 3.3315, 3.3326, 3.3527, 3.3523, 3.3535, 3.3537, 3.3545,
Notes: Hoogovens Aluminium Building Systems. 3.3547,3.2315,3.3211,3.1325,3.1355,3.1255, 3.4335, 3.4365,
3.4345; NF: A7, A5, A5L, A4, A-M1, A-MG 0,5, A-M1 G, A-M 1 G,
AG 0,6, A-G3M, A-G4MC, A-GS, A-SGM, A-U4G, A-U4G1, A-
Hoogovens Aluminium BV [AI] U4SG, A-Z5G, A-Z5GU; Aerospace grades: Air 9048; NF 50451,
Vondellaan 10, Beverwijk, Postbus 10000 50751; BS 2L93, 2L97; DTD 5120,5130; S07-1213; DAN 26,
NL-1970 CA Ijmuiden 422; VFN 13314, 13327, 13912; FED QQ-A 250/4, 250111,
Netherlands 250/12,250/29; AMS 4050, 4089 etc. Other alloys on request.
Tel +31 251 499105, Fax +31 251 470220 Designation systems: USA CEN ISO BS DIN NF Aerospace.
Group: Hoogovens Groep Product Types: Wrought alloys. Strip, sheet & plate.
Applications: Tanks and pressure vessels, building and
construction, parabolic antennae, automotive and coachwork,
Hoogovens Aluminium Danmark AlS [AI] rail transport, shipbuilding, aerospace, mechanical engineering,
Helgesh0j Aile 24 food industry.
DK-2630 Taastrup Tradenames: KAL-BAU, KAL-ZIP (building products)
Denmark Approvals ISO 9001.
Tel +4542 52 70 15, Fax: +4542 52 79 79, Telex: 33494 hoogal Notes: Sheet: 0.2 to 8mm thick, max width 1.5m, max coil dia
dk, Contact: Freddy Lund 1.35m. Plate: 4 to 175mm thick, up to 3.5m wide/22m long.
Group: Hoogovens Groep Est: 1923 Employees: 13
Notes Hoogovens Aluminium Distribution & Service Centre.
Supplier Addresses & Product Details 75
Hoogovens Aluminium GmbH [AI] Hoogovens Aluminium NV filial Sverige [AI]
Buro Neuss, Europadamm 2, Postfach 10 1523 Odinsgatan 13, PO Box 308
0-41415 Neuss S-40125 Goteborg
Germany Sweden
Tel: +49 2131 186821, Fax: +492131 186824 Tel +4631 806990, Fax: +4631 150420
Group: Hoogovens Groep Group: Hoogovens Groep
Notes: Hoogovens Aluminium Rolled Products Duffel.
Hoogovens Aluminium HOUenwerk GmbH [AI]
Postfach 10 11 54 Hoogovens Aluminium NV Profiel Centrum [AI]
0-46549 Voerde [Schleusenstral),e, 0-46562 Voerde] A. Stocletlaan 87
Germany B-2570 Duffel
Tel: +49 28194210, Fax: +492819421264, Telex: 812730, Belgium
Contact Dipl. Vw. Dieter Stahmann Tel +32 15 302220, Fax +32 15 302235
Group: Hoogovens Groep Est 1968 Employees: 505 Group Hoogovens Groep
Notes: Hoogovens Aluminium Distribution & Service Centre. Product Types: Wrought alloys, Extrusion.
Notes: Hoogovens Aluminium Extrusion Products.
Hydro Aluminium Seneffe SA [AI] Hydro Aluminium Vik Verk a.s [AI]
~~~~~~~----------------------~~
Zoning Industriel C P.O. Box 214
B-7180 Seneffe N-5860 Vik I Sogn
Belgium Norway
Tel: +3264520440, Fax +32645491 77, Contact: Mr. Guy Tel +4757695555, Fax: +47 57 69 55 00
Delmotte Group Norsk Hydro
Group Norsk Hydro Notes: Part of the Finished Products group. Traffic & safety
Product Types Wrought alloys. Profiles. Large conductors equipment. Building elements, e.g. tunnel cladding.
(cables). Tube, Wire, Extrusion, Conductors (cables).
Applications: Cables. Automobile.
Notes: Part of the heat transfer business. Hydro Alumino La Roca SA [AI]
Polig. Industrial Can Font de la Parera
Sta. Agnes de Malanyanes
Hydro Aluminium Suomi Oy [AI] E-08430 La Roca del Valles - Barcelona
Thurmansallen 8 Spain
SF-02700 Grankulla Tel: +34 3842 23 36, Fax: +34 3842 20 27
Finland Group: Norsk Hydro
Tel: +3580 505 30 77, Fax: +35 80 505 47 97 Product Types: Wrought alloys, Extrusion.
Group: Norsk Hydro
84 Supplier Addresses & Product Details
Hydro Aluminum Adrian, Inc. [AI] Hydro Magnesium [ Mg]
~~~~~--~--~------------------~~
1607 East Maumee Street Avenue Marcel Thiry 83
Adrian, Michigan 49221 B-1200 Brussels
United States of America Belgium
Tel: +1 517 2657141, Fax: +1 517263 3559 Tel +32 2 773 5211, Fax: +322 773 5450, Telex: 4624389 hydag
Group: Norsk Hydro b, Email: Francois.Borman@hmm.hydro.com. Contact: Dwain
Notes: Part of the Heat Transfer business. Magers - Director of Market Development
Group: Norsk Hydro
Associated Companies Market development office (user
Hydro Aluminum Automotive Structures, Inc. [AI] technical/marketing services): USA, Europe, Japan.
365 West 24th Street Alloys: ASTM B93-94a AZ91 D, AM60B, AM50A, AS41 B. Hydro
Holland, Michigan 49423 Alloy Spec: AM20. AS21, AE42. Designation systems USA
United States of America Proprietory.
Tel +16163966591, Fax' +1 6163966029 Product Types: Cast alloys, Powders Provide primary & alloy
Group: Norsk Hydro magnesium. Die casl alloys. Primary & secondary ingot. Powder,
Applications: Automotive. chunks & granules. Chips & turnings. Cast anodes. DC-Cast T-
Notes: Seat rails, seat frames & subframes. Bumper applications bars & cylinders. Ingot, anodes.
Applications Aluminium industry. Die-castings (automotive).
Desulphurisation of iron & steel.
Hydro Aluminum Cedar Tools Inc. [AI] Other Services Design support. Technical service. Scrap buyers.
104 West Beech Street, P.O. Box 560 Metering devices (molten metal). Approvals: ISO 9001
Cedar Springs, Michigan 49319 Notes: Metal Group Head Office for world's largest supplier of
United States of America magnesium diecasting alloys.
Tel +16166960873, Fax: +16166961261
Group: Norsk Hydro
Notes: Ex1rusion die production. Hydro Magnesium [ Mg]
Market Development Center, 21644 Melrose Ave.
Southfield MI-48075-7905
Hydro Aluminum Louisville, Inc. [AI] United States of America
9400 Williamsburg Plaza, Suite 120, Louisville Tel: +18103532629, Fax: +18103532625
Kentucky 40222 Group: Norsk Hydro
United States of America Product Types: Cast alloys.
Tel +1 5024267100, Fax: +1 5024238071 Notes: N. America Sales & Marketing office.
Group: Norsk Hydro
!.T.C. [AI]
Intermetaux SA [AI]
See: Hydro Aluminium I.T.C. s.n.c.
4 rue des Champs-Fourgons
F-92230 Gennevilliers
France Itochu Non-Ferrous Materials Co. Ltd. [ Ti]
Tel: +33 1 47940224, Fax +33 1 47940907, Contact Erick 2-15 Minami-Aoyama. 2-Chome, Minato-Ku, Tokyo 10
Martin Japan
Product Types: Wrought alloys. Rolled products. Tel +81 334978482, Fax +81 334978180, Email:
Notes: Late entry. hideaki.shibayama@nfmte.itochu.co.jp, Contact Ichita Kosaka -
President
International Extrusions [AI] Group: Itochu Corp. Est: 1968 Employees: 75
Associated Companies: Additional Sales Office(s)
5800 Venoy Road, Garden City, MI48135 Itochu International. Inc.
United States of America New York, NY United States of America
Tel: +1 3134278700, Fax: +1 3134278219 Tel: +12128188163, Fax: +12128188502
Product Types: Wrought alloys, Ex1rusion. Itochu (Thailand) Inc. Bangkok, Thailand
Other Services: Moulding, Forming. Milling, Metal Finishing, Tel: +6622663086. Fax: +6622663126
Powder Coatings, Protective Coatings. Product Types: Wrought alloys Cast alloys Specializing in
titanium sponge. ingot and mill products in transactions of
International Metal Company [ Mg] domestic, export, import and third countries. Alloying Additives,
Alloys, Bar & Rod, Billet. CP Billet, Briquettes, Commercial
See: IMCO Recycling Inc. Products, Sporting Goods, Electrodes, Remelting, Ex1rusions &
Extruded Shapes. Flats, Ingot & CP Ingot, Seamless Pipe,
Intexalu Systemes Puget SA [AI] Welded Pipe, Plate, Clad & CP Plate, Scrap, Turnings, Sheet,
Slab & CP Slab, Sponge, Strip, Tube, Tube - Finned, Tube -
ZI Camp Dessert Nord Welded, Wire & Wire Coil.
BP 12, F-83488 Puget sur Argens Cedex Other Services: Toll Processing.
France Notes: Annual sales of approximately US$ 400 million.
Tel +33494402727, Fax +33494452344/81 55 10, Telex
970492 f
Est 1978 Employees 250 G. James Australia Pty. Ltd. [AI]
Associated Companies: France Lyon, Tel: +33 4 78 90 28 68; Head Office - Administration
Strasbourg, Tel +33 3 88 33 96 66; Toulouse, Tel +33 5 61 76 1084 Kingsford Smith Drive, Eagle Farm
28 03; Vend6me, Tel +33 2 54 77 13 07. Brisbane. Queensland, PO Box 78, Hamilton Central
Alloys 6060. Temper T5 Designation systems NF Queensland 4007
Product Types: Wrought alloys Extruded profiles (to NFA 50.710 Australia
tolerances). Ex1rusion. Tel: +61 73877 2333, Fax +61 73877 2893, Telex AA 145277
Applications: Building fa9ades. Curtain walling. Roofing. Group: G. James (Australia) Est 1959 Employees 1700
Architectural/glazing systems (verandas, windows, doors, Associated Companies: Throughout Australia: Queensland, New
shutters, etc.) Handrail systems. South Wales, Victoria. Overseas Sales Office Singapore,
Notes Provide a complete service from concept design (CAD), Malaysia.
ex1rusion to surface finishing (20-25 microns anodized. various Product Types Wrought alloys Custom ex1rusions. Standard
colours & 'Qualicoat' painted in various colours) for profiles used angles. channels. flats & tubes. Glazing profiles. Ex1rusion
in architectural & building projects, inc. public buildings & private Applications: Building & architecture. Residential doors &
dwellings. Distribution centres across France. windows. Internal fittings (bathroom, etc). Roadside furniture
(posts). Roofing. Mobile scaffold.
Ireland Alloys Inc. [ Ti] Tradenames ArmaGrilie (security grill).
Other Services: Contracting (curtain walling, fa9ade, shop fronts,
P O. Box 41000, 11300 Spencer Road etc.). Surface finishing (anodising, paint & powder-coat in
Houston. TX 77241-1000 various colours). Welding (specialist).
United States of America Notes A privately owned group of aluminium & glass companies
Tel: +17139371111, Fax +17139371438, Email: providing glazing products, furniture, windows & doors (inc.
1051 02,550@compuserve.com, Contact Nick Oliver - Sales & bullet-proof). Group includes; G. James Glass & Aluminium
Operations Manager (QLD) Pty. Ltd.; G. James Ex1rusion Co Pty Ltd.; G. James
Group: Ireland Alloys (Holdings) Ltd. Est 1971 Employees 45 Safety Glass Pty. Ltd.
Associated Companies: Additional Sales Office(s):
Ireland Alloys Ltd.
Hamilton, Scotland G. James Industries (Malaysia) Sdn. Bhd. [AI]
Tel +44 1698 822461, Fax: +44 1698 825166 Lot 2596 Jalan Perindustrian 3, Kawasan Perindustrian Senai 11
Product Types: Wrought alloys Feedstock, Bulk Weldables, Buy 81400 Senai, Johor
& Sell, Scrap, Turnings. Malaysia
Other Services: Recycling, Toll Processing. Tel: +60 7 599 3266, Fax: +607 599 3213
Notes: Ireland Alloys Inc. specializes in processing Complex Group: G. James (Australia)
Nickel, Cobalt and Titanium based alloy scrap, and is one of the Product Types: Wrought alloys.
few recyclers in the United States of America approved to supply Notes: Sales Office.
88 Supplier Addresses & Product Details
G. James Singapore Pte. Ltd. [AI] Kaye Aluminium pic [ AI]
~~~~~~~~~~~--------------~~
Bugis Village 237 A, Victoria Street Ogden Road, Wheatley Hills, Doncaster DN2 4SG
Singapore United Kingdom
Tel: +657214508, Fax: +65 582 6108 Tel: +44 1302762500, Fax: +44 1302360307, Contact: Gary Coe
Group: G. James (Australia) - Designer
Product Types: Wrought alloys Group: Kaye
Notes: Sales office. Associated Companies: Also Enfield
Alloys AA designations: 6005A, 6063, 6082; AIMgSiO.5,
AIMgSiO.7, AIMgSi1. Tempers F, F13, F21, F22, F25, F26, F28.
Japan Metals & Chemicals Co. [Mg] F31, T4, T5, T6.
Metals & Electro-materials Div. Product Types: Wrought alloys Extruded sections up to max
JMC Building No. 8-4, Koaml-cho Nihonbashi Chou-ku, Tokyo 103 circumscribing circle of 200mm, from 0.13 to 12 kg/m. Standard
Japan lengths from 2.6 to 7m.
Tel: +81336671332. Fax: +81336691973, Contact: Mr. Tetsuo Applications: Building/architecture - windows; curtain walls.
Tanabe Other Services: Comprehensive design service. Polyester powder
Product Types: Cast alloys Primary pure & alloy ingot and paint finishing. Anodising and fabricating (by sub-
Notes: Annual capacity of 5000T for domestic market. JMC plant contractors; in-house) Thermal break
also at Toyama-ken, Japan. [Information provided by the
International Magnesium Association].
Koninklijke Hoogovens [AI]
Vondellaan 10, Beverwijk, Postbox 10000
Jimenez [AI] NL-1970 CA Ijmuiden
See: Industrias R. Jimenez SA Netherlands
Tel: +31 251 499111, Fax: +31 251 470057
Group: Hoogovens Groep
Josef Gartner & Co. [AI] Product Types: Wrought alloys
WerkstaUen fOr Stahl- und Metallkonstruktionen Notes: Head company of Hoogovens group.
Postfach 20/40
0-89421 Gundelfingen [Gartnerstrai?,e, 0-89423 Gundelfingen]
Germany Krupp Hoesch Steel Ltd. [ Ti]
Tel +499073840, Fax: +499073842100, Telex: 51531. Speedwell Industrial Estate, Staveley nr. Chesterfield
Contact: H. Schwaigner - Sales Manager Derbyshire S43 3JW
Group: Gartner Est: 1868 Employees: 2100 United Kingdom
Product Types: Wrought alloys, Semi-finished products. Tel +44 1246280280, Fax: +44 1246 280445, Telex: 54349,
Contact: Mandy Betteridge - Sales (Titanium)
Group: Deutsche Titan (D)
P.T. Justus Kimiaraya [AI] Associated Companies: Woking, Surrey.
JL. Kebon Jeruk 18 No. 2A-B, Jakarta 11150 Product Types: Wrought alloys Cast alloys Ingots - 4 tonne, mill
Indonesia production. (Deutche Titan, Titania). Shapes/profiles (c/o SW
Tel: +62 21 6397708, Fax: +62 21 626 0901, Contact: Tjandra Hempel).
Martaniardjo Notes Sales office (UK) for Deutsche Titan (D).
Group: Comalco
Notes: Distributor - Aluminium Pastes / Flakes
K-Trade Ltda [AI]
Av. Antonio Abrahao Caram, 820-sl. 1.011, Sao Jose
KACC [AI] Belo Horizonte, MG
See: Anglesey Aluminium Metal Ltd. Brazil
See: Kaiser Aluminum International Incorporated Tel: +55314431962, Fax: +5531 441 5407, Contact: Ana
See: Rio Tinto Aluminium Ltd. Claudia B. Kayser
Group: Comalco
Notes: Distributor - Aluminium Powder / Granules
Kaiser Aluminum International Incorporated [AI]
PO Box 877,6177 Sunol Boulevard
Pleasanton CA 94566 Lacagem de Metais [AI]
United States of America See: Tecnilaca Lacagem de Metais, Lda.
Tel: +15108475810, Fax +15108474700, Contact: Mark
Chistolini
Group: RTZlKACC Consortium Co. Lacal SNC [AI]
ZA du Garric, BP6
F-81450 Le Garric
Kapa GmbH [] France
Leichtsoffiecchnik, Kiefernweg 10, Postfach 2707 Tel: +33 5 63 80 20 20, Fax: +335 63 80 20 29
0-49090 Osnabruck Group SAPA
Germany Notes: Powder finishing plant
Tel: +49 541 121 93 0, Fax: +49 541 121 93 93
Group: Alusuisse-Lonza (CH)
Product Types Composites for inner-body shell Lachenal Industries [AIMg]
Notes: Member of the Alusuisse-Lonza (A-L) Aluminium Divison, Zlles Esserts, BP 8
an interdisciplinary team experienced in automotive industry F-74140 Douvaine
requirements. France
Tel: +33450941085, Fax: +334509421 12
Group: Groupe Valfond Est: 1936 Employees: 190
Karam Corporation [ Mg] Alloys: AS9U3, AS12U, AS12, Mg. Designation systems NF
Kang Nam, PO. Box 922, Seoul 135-609 Product Types: Cast alloys, Die castings.
South Korea Applications: Automotive, domestic and leisure goods, etc.
Tel: +822577 8920. Fax: +8225746637
Group: Norsk Hydro
Supplier Addresses & Product Details 89
Lawson Mardon Packaging Inc. [AI] London & Scandinavian Metallurgical Co. Ltd [AI MMC ]
6733 Mississauga Road, Suite 800 Head Office & Sales, 45 Wimbledon Hill Road, London SW19 7LZ
Mississauga, Ontario L5N 6P6 United Kingdom
Canada Tel +441819471221, Fax +441819472966, Telex 929830
Tel: +1 905821 9711, Fax: +1 905821 1454 Group: Metallurg (USA)
Group: Lawson Mardon Packaging Product Types: Cast alloys MMC's - particulate reinforced, Ingot,
Applications: Packaging, rod; tablets; MMC powders,
Notes: North America Head Office, Other Services Analytical Rod-feeding machines,
Notes: Manufacturers of aluminium grain refiners & master alloys
in rod & ingot form, AI-alloying tablets, [Information provided by
Lawson Mardon Packaging Ltd. [AI] ALFED]
Avonbank, Clifton Down, Bristol BS8 3HT
United Kingdom
Tel: +44 1179464200, Fax: +44 1179735810 London & Scandinavian Metallurgical Co. Ltd [ AI ]
Group: Lawson Mardon Packaging Fullerton Road, Rotherham, South Yorkshire
Applications: Packaging, United Kingdom
Notes: UK Head Office, Tel +44 1709828500, Fax: +44 1709830391, Telex 54581
Group: Metallurg (USA)
Product Types: Powders Metal Powders
Lawson Mardon Packaging SA [AI]
63 rue de l'Est
F-92100 Boulogne Lord Corporation [ Ti]
France Mechanical Product Division
Tel: +33 1 47124900, Fax: +33147124999 1952 W Grandview Blvd,
Group: Lawson Mardon Packaging Erie, PA 16514-0040
Applications: Packaging, United States of America
Notes: French Head Office, Tel: +1 8148685424, Fax: +1 8148681345, Contact: Wilbur C,
Hinkston - Manager Manufacturing
Group Lord Corporation Est: 1924 Employees: 1100
Lawson Mardon Star Ltd. [AI] Associated Companies: Subsidiaries Lord SA; Lord UK and
Stourbridge Road, Bridgenorth, Shropshire WV15 6AW Lord GmbH
United Kingdom Additional Sales Officers):
Tel: +44 1746 713 000, Fax: +44 1746 761860, Telex: 338130, Lord, Mechanical Prod, Div,
Internet: http://lawsonmardon,com, Contact: John Shipley- Erie, PA United States of America
Sales Tel: +1 8148685424, Fax: +1 8148683109
Group: Lawson Mardon Packaging Est: 1933 Lord, Mechanical Prod, Div,
Associated Companies: Worldwide, Head offices in UK, F, CH, Cary, NC United States of America
Canada, Tel: +19198594911, Fax: +19198515390
Alloys: AA: 1060, 1200, 3003, 8006, 8011, 8012A, 8021A, 8014, Applications: Mechanical Products for Aerospace & Industry,
Tempers: Fully annealed or hard, H19, H18, H22, H24, H26 Notes: Lord Mechanical Products Division designs, manufactures
LM Star alloy No, 1602,1201,1084,1085,3103,8101, and markets mountings, isolators, suspensions, and cancelation
Designation systems USA Propietory, systems to protect people and sensitive equipment from shock,
Product Types: Wrought alloys Convertor foil, thin strip & vibration and noise, Markets served include: aerospace,
household, Thickness 6,5-20 microns, 20-200 microns, Width automotive, on and off highway vehicles, marine, railroad, mass
300-140 mm, One- or two-sides bright. Container & Container transit, computer, HVAC, and many others requiring protection
Lidding Foil: 30-150 microns thick, 150-1300 mm wide, from shock, vibration & noise,
Laquered (epoxy or vinyl, total of 26 colours) or plain bright mill
finish, Dairy foil For bottle-capping 38-50 microns thick, 51, 88,
128 mm wide, Bright, undercoat, laquered or custom-printed Luxfer Gas Cylinders [AI]
finish, For plain & laquered lidding, 30 or 38 microns thick, Colwick, Nottingham NG4 2BH
1OOOmm max, width, For butter laminates, 8 micron (to customer United Kingdom
requirements), Confectionary foil 8,9,10,11,12 microns Tel +44 115980 3800, Fax: +44 115 980 3899
(normally supplied), width 40-1 050mm (varies with alloy type), Group British Aluminium Holdings (UK)
Plain, laquered or printed finish, Also confectionary laminates Product Types Wrought alloys, Extrusion,
(foil-on-paper/plastic) Foil, thin strip, Applications: Life-support/Breathing apparatus (safety workers);
Applications: Litho strip, convertor, household foil, container strip, Medical (oxygen & anaeshetics), Diving (commercial & leisure
confectionary, tobacco & industrial products, scuba tanks), Beverage dispensers, Airbag cylinders,
Approvals ISO 9002, FDA food regulations, Notes Development, production & supply of seamless extruded
Notes: Part of Alusuisse-Lonza group, Lawson Mardon Packaging aluminium (& composite) high-pressure gas cylinders for storage
is a worldwide operation with companies producing all types of of liquefiable & non-liquefiable gases, Manufacturing plants in
packaging for all industry sectors, inc, food-stuffs, beverages, UK (Nottingham, small cylinders - Staffordshire), USA
pharmaceuticals, technical uses, litho-printing, LM group R&D (California, N, Carolina), Australia (licensee in NSW)
activity sited in CH, 'Star' is one of Europes major foil
manufacturers, Integrated production company from casting
rolling slab, hot-rolling, cold-rolling to foil, slitting, lubricating to Luxfer USA Ltd. [AI]
packing & shipping, 1995 Third Street, PO Box 5300, Riverside, CA 92517
United States of America
Tel +1 9096845110, Fax: +1 909351 0790
L. M. P. [AI] Group: British Aluminium Holdings (UK)
Allee du Parc aux Boeufs Associated Companies: USA (Pennsylvania), Tel: +1 610565
F-77200 Torcy 1749, fax +16105654709, UK (Nottingham) tel +44115 980
France 3800, fax +44 115980 3899,
Tel: +33 1 60 06 30 24, Fax: +33 1 60 1725 96, Contact: Maurice Product Types: Wrought alloys,
Balbiani Applications: Gas cylinders(industrial, safety equipment, diving,
Est: 1969 Employees: 50 beverage, medical),
Notes: Late entry, Notes: Other USA manufacturing plants: Luxfer CompOSite
Cylinders (Palcentia, CAl; Graham (North Carolina),
90 Supplier Addresses & Product Details
_M-:a:-::g~C",:,o~r..:.:p~--=M=ag::::n,,!,"e~s~i_u_m_C_o..:rp_._o;...f_A_m.....:..e_ri..;.ca~_ _ _......::[..;.M;;.:g::...!.] Magnesium Elektron [Mg]
238 North 2200 West 500 Point Breeze Rd.
Salt Lake City, UT 84116 Flemington Junction NJ500
United States of America United States of America
Tel: +1 801 5322043, Fax: +1 801 5341407. Telex: 6711664, Tel: +1 9087825800, Fax: +1 9087827768
Contact: Mr. Michael Legge Group British Aluminium Holdings (UK)
Est: 1972
Alloys ASTM B843 (anodes): M1C high-potential anodes. Alloys:
AZ91D, AZ91E, AM50A, AM60B, AZ81A; Grade 9908A, Grade Marathon [ Ti]
9990A. Designation systems: USA. See SA Aciers Marathon Staal NV
Product Types Cast alloys Primary (pure & alloy) & secondary
ingot. Ingot sizes 25, 50, 250, 500 Ibs. Grinding slab (99.8%
pure): 37 lb. Die- & sand-casting ingot: 15/25 lb. Cast anodes. Mark Metals Inc. [Mg]
Cast (pure Mg) anodes. Ingot, anodes (cast) 12225 Coast Drive. Whittier CA 90601
Applications: Corrosion protection. Die- & sand-casters. United States of America
Aluminium alloying. Steelindustry Powder & chip production Tel: +13106927909, Fax: +13106928365, Contact: Mr
(grinding slab) Randall Biggs
Tradenames: MagMax (anodes) Product Types: Wrought alloys Cast alloys Extrusion & forging-
Other Services: Other alloys on request. billet: castings (die-, sand, permanent mould. investment);
Notes Third largest producer of primary magnesium worldwide Impact extrusions; forgings; Tooling & tread-plate; welding rods
Mg obtained by extraction from brine (Great Salt Lake) using & electrodes. Billet, Plate, Sheet, Wire.
solar energy (95% of processing enegry used). High-potential Other Services: Stockist. Scrap buyers.
anode business a co-venture with Garfield Alloys (USA). Notes: Distributor. USA: Toll-free 800 955 6404. [Information
MagMax anode plant at Rowley, UT & at Garfield Alloys in provided by the International Magnesium Association].
Cleveland, OH. Anode testing to ASTM G97 method. Product
range of over 30 different ingot shapes, sizes & alloys. Member
of the International Magnesium Association.
Marie [ Ti]
Odival, BP 46
F-52800 Nogent
Magnesium Corp. of America [Mg] France
See: MagCorp - Magnesium Corp of America Tel: +3332531 8579, Fax: +3332531 6265, Telex 840179 f.
Contact: Robert Favre
Est: 1972 Employees: 57
Magnesium Elektron [Mg MMC] Product Types: Wrought alloys.
PO Box 23, Swinton, Manchester, Lancs. M27 800 Applications Forged titanium items (prothesis).
United Kingdom Notes: Late entry.
Tel: +44 161911 1000, Fax +44161911 1010/25, Telex'
667817melmang, Contact: Mr S.R. Harris - Sales & Marketing
Manager M&C Metaux et Chimie [AI]
Group British Aluminium Holdings (UK) BP 7115
Alloys: Cast alloys (Elektron): WE54, WE43, QE22, EQ21, ZE41, F-95054 Cergy-Pontoise Cedex
EZ33, ZC63; Cast alloys AZ91, AZ81, AM60, AM50, AM20, France
AS41, AS21, AE42 (development alloy). Wrought alloys Tel: +33 1 3464 95 95, Fax: +33 1 3464 06 60, Contact: Mr.
(Elektron): ZC71, ZW3, ZM21, WE54, WE43; Wrought alloys: Perivier
AZ80, AZ61, AZ31. Metal Matrix CompOSites (wrought): Melram Product Types: Powders (aluminium & ferrous & precious & semi-
072, Melram 072TS. Welding rod (W=Elektron grades, precious for sintering [frittage]).
UK/USA) W1 (Pure Mg 99.5), W2(AM503/MIA-F), W4(HPAZ92), Notes: Late entry.
W5(ZM21), W6(ZRE1/EZ33A), W7(RZ5/ZE41A), W8(QE22A),
W9(ZE63A), W1 0(ZW1/ZK1 0), W13(MSR-B), W14(A8/AZ81), [ Mg]
W15(AZ31), W16(HPAZ101), W18(HPAZ91/AZ91 E),
MEL
W19(EQ21A), W21 (ZCM630/ZC63), W22(ZCM711/ZC71), See also: Magnesium Elektron
W23(W23IWE54). Designation systems: USA BS.
Product Types: Wrought alloys Cast alloys, Powders Casting & [ Mg]
wrought alloys. Speciality hardeners. Granules & raspings.
MEL Chemicals
Forging & extrusion billets. Melrnag sheets (electrochemical PO Box 6, Clifton Junction, Swinton, Manchester M27 8LS
uses). Welding rod (Mg-base & AI-alloy). Anodes. Semi- United Kingdom
fabricated products (used in Magnox nuclear reactors). Ingot, Tel: +441619111100, Fax +441619111099
billet, sheet, forgings/stock, anodes; welding rod. Group: British Aluminium Holdings (UK)
Applications: General engineering (cast components). Power Notes: Speciality zirconium chemicals for paper coating, pigments,
industry. Chemical industry. Corrosion protection (anodes). Steel water-proofing, paint driers, anti-perspirants, ceramics,
industry. Aero-industry. Automotive (pistons, etc.) electronics & catalysis. Manufacturing plants in UK (SWinton,
Tradenames MELMAG, MELRAM. Manchester); USA (Flemington, New Jersey & Aspen,
Other Services: Approval of foundries (list available from MEL). Pennsylvania).
Technical assistance. Product information/guidance available on
PC database. Approvals: BS ISO 9002 Metal Agencies Ltd. [ AI ]
Notes: Provide a range of magnesium alloys & other magnesium
speciality products. Production bases in UK (Swinton, Surrey House, 114, Tilt Road, Cobham, Surrey KT11 3JH
Manchester) & USA (Reade Manufacturing, Lakehurst, NJ), United Kingdom
which concentrates on particulates. Worldwide network of MEL Tel +441932860250, Fax: +44 1932867499
(Magnesium Elektron) approved foundries (audited) for gravity & Product Types: Wrought alloys. Rolled products. Plate, Sheet,
high-pressure die casting. Recycling facility in UK. Wide range of Strip, Foil.
welding rod grades (deSignated W). compositions of which may Notes Agent for Elval (Greece).
not conform exactly to nationallinternational specifications; their
compositions are tuned to aid welding.
Supplier Addresses & Product Details 91
Metal Casting Technology, Inc. [MMC] Associated Companies World-wide, USA (Birmingham,
Chicago, Houston, Los Angeles, Pittsburgh, Newfield, New York
Hitchiner Manufacturing City). UK Rotherham. Corporate offices in UK, CH, D. I, Canada,
Milford, New Hampshire 03055 Japan, Brazil, USA, S. Africa, E, Mexico, SW, Turkey. Agents:
United States of America Argentina, Australia, Austria, Chile, China, Colombia, Cosat rica,
Group: Hitchiner Manufacturing Co. Inc.
Denmark, Egypt, Finland, F. Greece, NL, Hong-Kong, India.
Alloys: Metal Matrix Composites - aluminum alloys with up to 40 Korea, Luxembourg, Malaysia, Morocco, New Zealand, Norway,
percent silicon carbide reinforcement using countergravity Peru, Phillipines, Portugal, Venezuela.
investment casting. Product Types Powders Speciality metals, alloys, metal-based
Product Types: Cast alloys. Metal Matrix Composites. chemicals & powders. Master alloys. Metal powders.
Notes: General Motors Corporation and Hitchiner Manufacturing Notes One of the worlds foremost manufacturers & suppliers of
Co. Inc. joint venture research and development company. MMC ferrous, non-ferrous metals & alloys, metal-based chemicals &
production casting carried out by: Hitchiner's Nonferrous Division complementary products With producing works & 3 mining
in O'Fallon, Missouri. operations.
Metalchimica Sri [AI Mg Ti] Metallurg (South Africa) Pty Ltd. [AI Mg Ti]
Casella Postale 397 PO Box 14676, Wadeville 1422, Germiston
1-10100 Torino South Africa
Italy Tel +27 11 9026930, Fax +27 11 9025749, Telex 748713
Tel: +396692057, Fax +396698116, Telex: 221331 Group Metallurg (USA)
Group Metallurg (USA) Product Types: Powders.
Product Types: Powders.
SAPAAB [AI]
Russian National Aluminium-Magnesium Institute [AI Mg] Box 174, S-685 34 Torsby
VAMI Ltd. Sweden
86 va Stedny pr Tel: +4656012640, Fax: +4656012750
RU-199026 St. Petersburg Group: SAPA
Russia
Tel: +78122135458, Fax: +78122175966, Telex: 121598
SAPAAB [AI]
Box 17, S-915 21 Robertsfors
Sweden
Tel: +46934 14870, Fax: +46934 14835
Group SAPA
Supplier Addresses & Product Details 103
SAPAAB [ AI] SAPA Danmark AlS [AI]
Box 100, S-730 50 Skultuna Rolsh!1ljvej
Sweden DK-8500 Grena
Tel: +4621 78250, Fax +4621 75054 Denmark
Group: SAPA Tel +45 86 32 61 00, Fax: +45 86 32 66 63, Contact Per Lund
Group: SAPA Est: 1970 Employees: 140
Product Types: Wrought alloys, Extrusion.
SAPAAB [ AI] Approvals: ISO 9002.
Stampgatan 34, S-411 01 Gothenburg
Sweden
Tel: +46 31 801410, Fax: +46 31 153722 SAPA Holdings Ltd. [AI]
Group: SAPA Joseph Pitt House, Pitville Circus Road, Cheltenham
Gloucestershire GL52 2QE
United Kingdom
SAPA Aluminium BV [ AI] Tel +44 1242245333, Fax +441242520216
Nijverheidsweg 9, Postbus 102 Group: SAPA
NL-9600 AC Hoogezand Associated Companies: Derby: Fax +441773874389
Netherlands Product Types: Wrought alloys, Foil, Extrusion
Tel: +31 5980 199 11, Fax: +31 598393673 Approvals: BS 5750, ISO 9002.
Group SAPA Notes: Parent company for SAPA UK operation. Aluminium
Product Types: Wrought alloys, Extrusion. extrusion and finishing, building products and systems,
Other Services: Anodising. Approvals: ISO 9002. aluminium foil lidding.
Aluminum Foil Container Manufacturers Association APICS - American Production & Inventory Control
14 Bluff Oak Retreat Society
Savannah, GA31411 500 W. Annandale Road
United States of America Falls Church, VA 22046-4274
Tel: +1 9125988463 United States of America
Fax +1 9125988465 Tel: +1 703 237 8344
Contact: Brock Richardson - Executive Secretary Fax: +1 703 237 8450
Internet: www.industry.netJapics
Other Useful Addresses 135
Appliance Recycling Information Center Association of Container Reconditioners - NABADA
701 Pennsylvania Avenue, NW 8401 Corporate Dr., # 425
Suite 900 Landover MD 20785-2224
Washington, DC 20004 United States of America
United States of America Tel: +1 301 577 3786
Tel +1 2024347492 Fax: +1 301 577 6476
Internet: www.aham.org/mfrs/ariclaric.htm Email: dworcester@igc.apc.org
Internet: httpllwww.reconditioners.com
ARI - Air-Conditioning & Refrigeration Institute Contact: D. Worcester
1501 Wilson Boulevard, 6th Floor RECONET, or the Reconditioners Network, is a voluntary
Arlington, VA 22209 commercial seNice created to provide a prompt, reliable, effiCient,
United States of America and environmentally safe disposition option for container users To
Tel: +1 7035248800 use the network, contact a reconditioner in your area and ask for
Fax: +1 7035283816 the "Responsible Container Management Representative. "
Internet: www.ari.org Additional information on responsible container management.
Contact: Clifford H. "Ted" Rees, Jr - President including proper emptying practices, is also available through the
association.
Arizona Mining Association
2702 North Third Street, Suite 2015 Association of Home Appliance Manufacturers (AHAM)
Phoenix, AZ 85004 20 N. Wacker Drive, Suite 1231
United States of America Chicago, IL 60606
Tel: +1 6022664416 United States of America
Fax: +16022664418 Tel: +1 3129845800
Contact: Charles W. Shipley - President Fax +1 3129845823
Internet: www.aham.org
ASCE - American Society of Civil Engineers
World Headquarters ASTM - American Society for Testing and Materials
1801 Alexander Bell Drive 1916 Race Street
Reston, VA 20191-4400 Philadelphia, PA 19103
United States of America United States of America
Tel +1 703 295 6000 Tel: +1 2152995400
Internet: www.asce.org Fax: +1 215977 9679
Contact: James E. Davis - Executive Director Internet: www.astm.com
Toll Free (USA). 800-548-2723 Contact: James A. Thomas - President
Other branches. ASTM standards and other information.
ASCE - New York, Tel: +1 212-705-7010: Fax: +1 212-705-7712
ASCE - Washington, Tel." +1202-789-2200, Fax: +1 202-289-6797 ASTM - American Society for Testing Materials
100 Barr Harbor Drive
ASM International West Conshohocken, PA 19428-2959
9639 Kinsman Road United States of America
Materials Park, OH 44073-0002 Tel: +1 6108329585
United States of America Fax + 610 832 9555
Tel: +1 2163385151 Email: service@local.astm.org
Fax: +1 2163384634 Internet: http://wwwastm.com
Internet: www.asm-intl.org Standards Enquiry Office: httpJ/www.astm.com
Contact: Michael J. DeHaemer - Managing Director
Toll Free. 800-336-5152 (US. and Canada) Automotive Recyclers Association
3975 Fair Ridge Drive
ASME - American Society of Mechanical Engineers Suite 20, Terrace Level North
345 East 47th Street Fairfax, VA 22033-2924
New York, NY 10017 United States of America
United States of America Tel +1 703385 1001
Tel +1 2127057722 Fax: +1 7033851494
Fax: +1 2127057739 Internet: www.autorecyc.org
Internet: www.asrne.org
Contact: Dr. David L. Belden - Executive Director AWMI - Association of Women in the Metal Industries
National Headquarters
ASME - American Society of Mechanical Engineers 515 King Street, Suite 420
ASME Information Central Alexandria, VA 22314-3103
22 Law Drive United States of America
PO Box 2900 Tel: +1 7037398335
Fairfield, NJ 07007-2900 Fax: +1 7036846048
United States of America Internet: www.awmi.com
Tel +1 201 882 1167 Contact: Susan Ferns - President
Fax +1 201 8825155
Internet: www.asme.org BSI - British Standards Institute Inc.
Tycon Towers at Tyson Corner
8000 Towers Crescent Drive, Suite 1350
Vienna, VA 22182
United States of Arnerica
Tel: +1 7037607828
Fax: +1 703 761 2770
136 Other Useful Addresses
Builders Hardware Manufacturers Association Copper Development Association Inc. (CDA)
355 Lexington Ave., 17th Fl. 260 Madison Avenue
New York, NY 10017 New York, NY 10016
United States of America United States of America
Tel: +12126614261 Tel: +1 212251 7200
Fax: +1 2123709047 Fax: +1 212251 7234
Internet: www.bhma.com Internet: www.copper.org
DATA SHEET
Example
.------------------,
Alloy designation number Alloy designation system with
or name (proprietory) Details of alloy country or company name
1035
AA (USA) Wrought
Official composition: Si 0.35, Fe 0,6, Cu 1, Mg 0,05, Mn 005, Zn 1, Ti 0,03, V 0,05, Others Each 0,03, Aluminium 99.35 min, Density (kg,m 3) 2705
Comments See AA documentation for method of expressing AI content.
1040
AA (USA) Wrought
Official composition: Si 0,3, Fe 0,5, Cu 0,1, Mg 0,05, Mn 0,05, Zn 1, Ti 0,03, V 0,05, Others: Each 0,03, Aluminium 99.4 min, Density (kg,m 3) 2705
Comments: See AA documentation for method of expressing AI content
2010 Wrought
AA (USA)
Official composition: Si 0,5, Fe 0,5, Cu 0.7-1.3, Mg 04-1, Mn 1-04, Zn 0,3, Cr 0,15, Others: Each 0,05 Total 0,15, Aluminium rem, Density (kg,m 3) 2720
Identified Product forms Sheet/strip
Similar/Equivalent alloys: USA: AA2010; Proprietary: Reynolds 2010
Comments: Vehicle body sheet
21000
CEN EN 1706 (Europe) Cast
Nominal composition: Si 0.15, Fe 0.3, Cu 4.2-5, Mg 0.2-0.35, Mn 0,1, Zn 0.1, Ni 0,05, Ti 0.15-0.25, Pb 0,05, Sn 0,05, (Mg 15-0.35, Si 0.2, Fe 0.35 in finished casting),
Others: Each 0.03 Total 0.1, Aluminium rem.
Identified Product forms: Sand cast, Permanent mould cast, Ingot
Similar/Equivalent alloys: European (CEN): AC-21000; AC-AICu4MgTi {1{ill1: AI-Cu4MgTi
Condition [Form] PS (MPa) YS (MPa) UTS (MPa) EI ('!o)E (GPa) Hardness Notes (Source)
T4 [Chill cast] 200 320 8 95HB Min. values (VAW-IMCO)
T4 [Sand cast] 200 300 5 90HB Min. values (VAW-IMCO)
~5~1~1_0~0__~~~~~~~~~~~~~~C~E~N=E~N~1~7~0~6~(E~u~ro~p~e~)~~~~~~~~__~~__~~Cast
Nominal composition: Si 0.45, Fe 0.4, Cu 0.D3, Mg 2.7 -3.5, Mn 0.45, Zn 0.1, Ti 0.15, (Cu 0.05, Mg 3.5; Si 0.55; Fe 0.55; Ti 0.20 in finished casting). Others Each 0.05
Total 0.15. Aluminium rem.
Identified Product forms: Ingot
Similar/Equivalent alloys: European (CEN): AC-51100: AC-AI-Mg3(a): Germany: VDS 242
Condition [Form] PS (MPa) YS (MPa) UTS (MPa) EI ('!o)E (GPa) Hardness Notes (Source)
As cast[ Chill cas~ 70 150 5 50H B Min. values (VAW-/MCO)
As cast [Sand cast] 70 140 3 50HB Min. values (VAW-/MCO)
AG.2S
-;;:-----;-:----~----;o:-;:-c -------------
GM Metal (France) Cast
Proprietory composition, Si 0,1, Fe 0,2, Mg 23-27, Others, Each 0,05, Aluminium rem,
Identified Product forms: Ingot
Comments: Mother alloy for making magnesium additions to aluminium alloy melts, Small ingots (600mm long) weighing 1 kg, Breakable into 100 g portions, Deliverable in
packs of 600 kg
AI1
GOST 2685-75 (Russia (CIS)) Cast
Nominal composition: Si 0.7, Fe 0.7, Cu 3.75-4,5, Mg 1.25-1.75, Zn 1, Ni 1.75-2,25, Ti 0,1, Zr 0,1, Fe 0,8 for Chill Cast, Others Total 14. All llinium rem,
Identified Product forms: Permanent mould cast, Ingot
C357.2 AA (USA)
Cast
Official composition: Si 6,5-7.5, Fe 0,06, Cu 0,03, Mg 0,5-0.7, Mn 0,03, Zn 003, Ti 0,04-0.2, Be 0,04-0,07, Others Each 0.Q3 Total 1, Aluminium rem,
Identified Product forms Ingot
C380.1
AA (USA) Cast
Official composition: Si 7.5-9,5, Fe 1, Cu 3-4, Mg 15-0.3, Mn 0,5, Zn 2.9, Ni 0,5, Sn 0.35, Others: Total 0,5, Aluminium rem,
Identified Product forms: Ingot
Comments: Designation added to AA (USA) register since previous issue (01/89)
Ink Lining Ronald Britton & Co. (UK) Flake Aluminium Powder
Approximate composition: Aluminium 97 min.
Comments: For inks and pigments. Particle size. 14 microns.
Super Ink Lining Ronald Britton & Co. (UK) Flake Aluminium Powder
Approximate composition: Aluminium 97 min.
Comments: For inks and pigments. Particle size 10 microns.
Magnesium Alloys
Condition [Form] PS (MPa) YS (MPa) UTS (MPa) EI (%) E (GPa) Hardness Notes (Source)
[Sheet] 131 232 13 RT typical properties (#5)
M [Extru, Bar/section] 162 255 11 RT typical properties (#5)
M [Sheet] 170 263 10 RT typical properties (#5)
Titanium Alloys
.3~-2~.~5~~==~~~~~~~~~~~~~T_im~et~a~I(~U~S~A~)____________________________~~_r_ou_gh_t
Approximate composition: A13, V 2.5, Titanium rem. Density (kg.m') 4510
Identified Product forms: Plate, SheeUstrip, Tube, Extrusion, Forging stock/Billet, Rod, Bar, Wire
Similar/Equivalent alloys: USA UNS R56320, ASTM B337 3AI~2.5V; Grade 9, AMS 4943, 4944 European (CEN): Ti P69 (AECMA): Ti P69; Ti P609; France T~A3V2,
T~A3V5; Germany LW. 3.7194, Wk. 3.7195; Proprietary TimetaI3~2.5; IMI325
Comments: Alpha~Beta phase alloy. Normally used in cold~worked stress~relieved condition. Honeycomb foil, hydraulic tubing, pressure vessels. Weldability: Weldable
Condition [Form) PS (MPa) YS (MPa) UTS (MPa) EI (%) E (GPa) Hardness Notes (Source)
Annealed [-] 553 655 20 107 Typical (3AI~2.5V) (#3)
Not stated [-] 550 650 15 112.5 Typical (TimetaI3~2.5) (Timetan
Nominal composition: AI4.S-S.7S, Sn 2-3, Fe 0.25,0,0.12, N2 O.D3S, H2 0.012S, C 0.05, O+Fe 0.32, Y O.ooS, Others: Each O.OS Total 0.3, Titanium rem.
Identified Product forms: Plate, Sheetistrip, Extrusion, Wire
Similar/Equivalent alloys USA. UNS RS4S21 AMS 4909, 4924; Russia (C/S): VT51
Comments: Extra-low interstitial (ELI) grade. Improved ductility and toughness. Pressure vessels for liquefied gases and cryogenic service. Also castable.
Identified Product forms: Plate, Sheet/strip, Tube, Extrusion, Rod, Bar, Wire
Similar/Equivalent alloys USk ASTM B265, 337, 338, 348, 367, 381: Grade 12; Proprietory Timetal Code 12; IMI Code 12
Comments: Better corrosion resistance and strength than CP titanium grades. Chemical industry. Corrosion resistance: Good Weldability: Highly weldable.
Condition IForml PS (MPa) YS (MPa) UTS (MPa) EI ('!o) E (GPa) Hardness Notes (Source)
Not stated. [oj 460 600 22 112.5 Typical (Timeta0
T 40
---c----c---,----~-~~~~~~~~~~-----~~--''-----~~-------.-.---.
NF (France) Cast
Approximate composition: Fe 0.2,0, OA, N2 0.05, H, 0.015, C 0.10, Titanium rem. Density (kg.ml) 4500
Identified Product forms: Plate, Sheetistrip, Pipe, Forging stock/Billet
Similar/Equivalent alloys USA UNS R50400, ASTM Grade 2, AMS 4902, 4941; European (CEN): Ti P99002 (AECMA) Ti P99002 (was Ti P02); France T 40; Germanv
LW. 3.7034; Wk 3.7035; Japan JIS Class 3. H4600, H4630, H4650, H4670; UK 2TA2, 3, 4, 5; DTD 5013B, 5033B, 5183, 5293; Proprietory IM1125; Timetal50A
Comments: Commercial purity. Grade C2. For corrosion resistance in chemical, marine, aerospace and medical applications.
Condition [Form] PS (MPal YS IMPal UTS (MPal EII'!ol E (GPal Hardness Notes (Source)
Annealed [Castings] 275 345 15 (Taramm)
Ti 17 (USA) Wrought
Approximate composition: AI 5, Sn 2, Zr 2, Mo 4, Cr 4, Fe 0.3, 0,0.13, N2 0.04, H, 0.0125, C 0.05, Titanium rem.
Identified Product forms: Forging stock/Billet
Comments: Forgings. Alpha-rich near-Beta alloy. Good creep strength to 430C
Condition [Form] PS (MPal YS (MPal UTS (MPal EI (%l E (GPal Hardness Notes (Source)
STA [-I 1173 12 Typical (Ti 17) (#3)
~T_i_P_6~2~____~~~~~~______________A_E_C_M_A_(~E_U_rO~p_e~)_____________________________W_rought
Approximate composition: A14, Mn 4, Titanium rem,
Similar/Equivalent alloys USA: ASTM B348/7, B381 F7, AMS 4925A, SAE 4A14Mn; European (AECMA): Ti P62; France: TA 5M; UK DTD 5053, 5143; Proprietary
Crucible Steel Co, C130AM; IM1314A; IC1314A; Ti314A
~T_i~P_9~O_O_1-=~~~~~~~~~~~~~A~E~C~M~A~(~U_K~)~~~__~~~~__~~~~~W~rought
Nominal composition Cu 2-3, Fe 0,2,020,2, N, 0,05, H2 0,01, C 0,08 (for sheet, strip & forging: H 0012), Others Total OA, Titanium rem, Density (kg,m 3) 4560
Identified Product forms: Plate, SheeVstrip, Extrusion, Forging stock/Billet, Rod, Bar, Wire
Similar/Equivalent alloys: European (CEN): Ti P11 (AECMA): Ti P9001 (was Ti P11); France T-U2; Germany DIN TiCu2; LW, 3.7124; UK: BS 2TA21, 2TA22, 2TA23,
2TA24, 2TA52, 2TA53, 2TA54, 2TA55, 2TA58; DTD: 5123, 5133, 5233, 5243, 5253, 5263; Proprietary: De,Titan Tikrutan LT 25; Timetal230; IMI230
Comments Was Ti P11, RT phase type: Alpha, Useful properties to 350C, Weldability: Good
Condition [Form] PS (MPa) YS (MPa) UTS (MPa) EI (%) E (GPa) Hardness Notes (Source)
Aged [Rod] 580 740 20 125 Typical (IMI230) (#5)
Aged [Sheet] 670 770 20 Typical (IMI 230) (#5)
Annealed [-] 510 620 25 112,5 Typical (TimetaI230) (TimetaD
Annealed [Rod] 500 630 24 Typical (IMI 230) (#5)
Annealed [Sheet] 520 620 24 125 Typical (IMI 230) (#5)
mH ~ ~ W 112.5 Typical (TimetaI230) (Timetan
Beryllium Alloys
S-200FH --------------
Brush Wellman (USA) Wrought
Proprietary composition BeO 1 5 max Beryllium 99.5 min
Comments Structural Grade (Standard Punty)
Nearnel shapes by HIP
Max ppm AI 1000. C 1JOO Fe' 300. Mg 800. SI 600. Other. each max 400
!jsed for ocachlned parts
Inertial gUidance systems Missile mterstages. Optical substrates Spacecraft structures. Small rocket nozzles
CO'ldlt,on iECJrfllj PS (MPal YS IMPa) UTS (MPa) EI ('!o) E (GPa) Hardness Notes (Source)
H!P [IJea' Net Shapes! 276 414 2 Min. values. Microyield 27 -41 MPa min.(Brush Wellman)
APPENDIX A : STANDARDS
A compilation of international, national and industry standards and speCifications commonly quoted within the light-metals
industries. Grouped by base-metal, then listed by organisation and their reference code.
APPENDIX C : GLOSSARY
A list of terms commonly used in the light metal industry. They are a mixture of those used to describe the materials
themselves (metallurgical) and their processing, production and characteristics.
APPENDIX D : VOCABULARY
Multilingual listing of key words in English-French-German-Italian-Spanish
Appendix A
Standards
This section contains a compilation of specifications and standards commonly quoted within the light-alloys industries. These
are divided as relating to:
o Aluminium
o Titanium
o Magnesium
o Beryllium
Within each category, specification codes are listed by the organisation, e.g. ASTM, DIN, EN, ANSI, etc.
No responsibility is taken for the use of this listing, for errors, for omissions, or for the failure to advise of subsequent revisions
or amendments. Standards and specifications are revised periodically, the appropriate specification index published by the
specification issuing body should be consulted to determine the latest issue. CEN standards are available through the
National Specification organisation. Many specification organisations now have Internet Web Sites. Advice may also be
sought from various Associations.
ALUMINIUM ALLOYS QQ-A-225/4 : 2014 roiled, drawn, or cold finished wire, rod
& bar
QQ-A-225/5 : 2017 rolled, drawn, or cold finished wire, rod
Aluminum Association (USA) & bar
[See also: Review - Further Reading list] QQ-A-225/6 : 2024 roiled, drawn, or cold finished wire, rod
& bar
Registration Record of Aluminium Association Designation
& Chemical Composition Limits for Aluminium Alloy QQ-A-225/7 : 5052 roiled, drawn, or cold finished wire, rod
Castings & Ingots (1996) & bar
Registration Record of Aluminium Association DeSignation QQ-A-225/8 : 6061 rolled, drawn, or cold finished wire, rod
& Chemical Composition Limits for Wrought Aluminium & bar
& Aluminium Alloys (1997) QQ-A-225/9 : 7075 rolled, drawn, or cold finished wire, rod
& bar
USA Federal Specifications QQ-A-225/10 : 6262 roiled, drawn, or cold finished wire, rod
& bar
FED. STD. 184: Item identification marking for aluminum
QQ-A-250 : General specifications for sheet & plate
products
QQ-A-250/1 : 1100 sheet & plate
FED. STD. 245 : Tolerances for aluminum wrought products
QQ-A-250/2 : 3003 sheet & plate
QQ-A-225 : General specification for roiled, drawn, or cold
finished wire, rod, bar & special shapes QQ-A-250/3 : Alclad 2014 sheet & plate
QQ-A-225/1 : 1100 rolled, drawn, or cold finished wire, rod QQ-A-250/4 : 2024 sheet & plate
& bar QQ-A-250/5 : Alclad 2024 sheet & plate
QQ-A-225/2 : 3003 rolled, drawn, or cold finished wire, rod QQ-A-250/6 : 5083 sheet & plate
& bar QQ-A-250/7 : 5086 sheet & plate
QQ-A-225/3 : 2011 roiled, drawn, or cold finished wire, rod QQ-A-250/8 : 5052 sheet & plate
& bar
QQ-A-250/9 : 5456 sheet & plate
Appendix A - Standards 353
USA Federal Specifications (Aluminium) - continued. ASME - American Society of Mechanical
QQ-A-250/10 : 5454 sheet & plate Engineers
QQ-A-250/11 : 6061 sheet & plate
S8209: 1060, 1100,3003, Alclad 3003, 3004, Alclad 3004,
QQ-A-250/12 : 7075 sheet & plate 5050,5052,5083,5086,5154,5254,5454,5456,
QQ-A-250/13 : Alclad 7075 sheet & plate 5652,6061 & Alclad 6061 sheet & plate
QQ-A-250/14 : 7178 sheet & plate S8210 : 1060, 3003, Alclad 3003, 5052, 5154, 6061, & 6063
QQ-A-250/15 : Alclad 7178 sheet & plate drawn seamless tube
QQ-A-250/18 : Alclad one side 7075 sheet & plate S8211 : 2014, 2024 & 6061 rolled, drawn, or cold finished
wire, rod & bar
QQ-A-250/21 : 7178-T76 & T7651 sheet & plate
S8221: 1060,1100,2024,3003,5083,5086,5154,5454,
QQ-A-250/22 : Alclad 7178-T76 & T7651 sheet & plate
5456, 6061 & 6063 extruded rod, bar, & shapes
QQ-A-250/24 : 7075-T76 & T7651 sheet & plate
S8234: 1060,3003, Alclad 3003, 5052, 5454, & 6061
QQ-A-250/25 : Alclad 7075-T76 & T7651 sheet & plate drawn, seamless tube for condensers & heat
QQ-A-250/26 : 7011 Alclad 7075 sheet & plate exchangers
QQ-A-250/28 : 7011 Alclad 7178 sheet & plate S8241/S8241M : 3003, 6061 & 6063 seamless pipe; 1060,
QQ-A-250/29: 2124-T851 plate 1100,3003, Alclad 3003,5052,5083,5086,5454,
5456, 6061 & 6063 seamless extruded tube
QQ-A-250/30 : 2219 plate & sheet
S8247 : 5083 & 6061 hand forgings; 2014, 3003, 5083 &
QQ-A-430 : Wire & rod for rivets & cold heading: 1100, 6061 die forgings
2017,2024,2117,2219,3003,5005,5052,5056,
6053,6061,7050,7075 S8308/S8308M : 6061 rolled or extruded standard
structural shapes
QQ-A-1876: Aluminum foil
VI/W-T-700 : General specification for drawn tube, seamless
ASTM - American Society for Testing &
VI/W-T-700/1 : 1100 drawn tube, seamless
Materials
VI/W-T-700/2 : 3003 drawn tube seamless
VI/W-T-700/3: 2024 drawn tube seamless A846-85(1993) : Aluminum Scrap for Use in Deoxidation &
Alloying of Steel
VI/W-T-700/4 : 5052 drawn tube seamless
8108-96a : Aluminum-Alloy Permanent Mold Castings
VI/W-T-700/5: 5086 drawn tube seamless
8136-84(1993) : Measurement of Stain Resistance of
VI/W-T-700/6 : 6061 drawn tube seamless Anodic Coatings on Aluminum
VI/W-T-700/7 : 7075 drawn tube seamless 8179-96: Aluminum Alloys in Ingot & Molten Forms for
Castings from All Casting Processes
USA Military Specifications B209-96: Aluminum & Aluminum-Alloy Sheet & Plate: 1060,
1100,2014, Alclad 2014, 2024, Alclad 2024 Alclad one
MIL-A4W27 : 5083 & 5456 armor plate
side 2024,2124,2219, Alclad 2219,3003, Alclad 3003,
MIL-A4W83 : 5083, 5456 & 2219 extruded armor 3004, Alclad 3004,3005,3105,5005,5050,5052,
MIL-A-8625 : Anodic coatings for aluminum alloys 5083,5086,5154,5252,5254,5454,5456,5457,
MIL-A-12545: 1100,2014,6061,6070, & 7075 impacts 5652, 5657, 6061, Alclad 6061, 7075, Alclad 7075,
Alclad one side 7075,7178, Alclad 7178 sheet & plate
MIL-A-22771 : 2014, 2219, 2618, 6061, 6151, 7049, 7050,
7075, & 7075 forgings & rings B209M-95 : Aluminum & Aluminum-Alloy Sheet & Plate
[MetriC]
MIL-A-45225 : 5083 & 5456 forged armor
B210-95: Aluminum & Aluminum-Alloy Drawn Seamless
MIL-A-46118 : 2219 armor plate & forgings Tubes: 1060, 1100,2011,2014,2024,3003, Alclad
MIL-A-81596 : 2024, 3003, 5052 & 5056 foil 3003,5005,5050,5052,5083,5086,5154,5456,
MIL-8-20148 : 4047 & 4343 brazing sheet 6061, 6063, 6262 & 7075 drawn, seamless tube
MIL-C-915 : Alclad 5056-H392 wire 8210M-95 : Aluminum & Aluminum-Alloy Drawn Seamless
Tubes [Metric]
MIL-C-5541 : Chemical films for aluminum & aluminum
alloys B211-95a : Aluminum & Aluminum-Alloy Bar, Rod, & Wire
(rolled, drawn, or cold-finished): 1060, 1100, 2011,
MIL-H6088 : Heat treatment of aluminum alloys
2014,2017,2024,2219,3003,5052,5056, Alclad
MIL-P-25995 : 3003, 6061 & 6063 pipe 5056,5154,6061,6262,& 7075
MIL-STD-129 : Marking for shipment & storage B211 M-95a : Aluminum & Aluminum-Alloy Bar, Rod, & Wire
MIL-T-5077-7 : 2024 seamless drawn tube [Metric]
MIL-W-6712: 1100 & 4043 metal spraying wire B221-96 : Aluminum & Aluminum-Alloy Extruded Bars,
Rods, Wire, Profiles, & Tubes: 1060, 1100,2014,2024,
2219,3003, Alclad 3003, 3004, 5052, 5083, 5086,
AMS - The American Welding Society 5154,5454,5456,6005,6061,6063,6066,6105,
A5.3 : Specification for aluminum & aluminum alloy 6262, 6351, 6463, 7005, 7075, & 7178.
electrodes for shielded gas metal arc welding B221M-96: Aluminum & Aluminum-Alloy Extruded Bars,
A5.10 : Specification for bare aluminum & aluminum welding Rods, Wire, Profiles, & Tubes [MetriC]
electrodes & rods B230. 1350-H19 wire
B231 : Aluminum conductors, concentric-lay-stranded
354 Appendix A - Standards
ASTM (Aluminium) - continued. B37-96 : Aluminum for Use in Iron & Steel Manufacture
B232 : Aluminum conductors, steel reinforced, B380-85(1990) Corrosion Testing of Decorative
concentrically-stranded (ACSR) Electrodeposited Coatings by the Corrodkote
B233 : 1350 drawing stock for electrical purposes Procedure
B234-95 : Aluminum & Aluminum-Alloy Drawn Seamless B396-87e1 : Aluminum-Alloy 5005-H19 Wire for Electrical
Tubes for Condensers & Heat Exchangers: 1060, Purposes
3003, Alclad 3003, 5052, 5454, & 6061. B397-85e1 : Concentric-lay-Stranded Aluminum-Alloy
B234M-95 : Aluminum & Aluminum-Alloy Drawn Seamless 5005-H 19 Conductors
Tubes for Condensers & Heat Exchangers [Metric] B398M-97 : Aluminum-Alloy 6201-T81 Wire for Electrical
B236-95 : Aluminum Bars for Electrical Purposes (Bus Purposes [Metric]
Bars/conductor): 1350 8399-97 : Concentric-lay-Stranded Aluminum-Alloy 6201-
B236M-95 : Aluminum Bars for Electrical Purposes (8us T81 Conductors
8ars) [Metric] 8399M-92 : Concentric-lay-Stranded Aluminum-Alloy 6201-
B241/8241M-96 : Aluminum & Aluminum-Allay Seamless T81 Conductors [Metric]
Pipe & Seamless Extruded Tube: 3003, 6061,6063, & B400 : Compact round concentric-lay-stranded, 1350
6351 seamless pipe; 1060, 1100,2014,2024,2219, conductors, hard-drawn
3003, Alclad 3003, 5052 5083, 5086, 5254, 5454, B401 : Compact round, concentric-lay-stranded aluminum
5456, 5652, 6061,6063, 6351, 7075, & 7178 seamless conductors, steel reinforced (ACSR)
extruded tube
B404-95 : Aluminum & Aluminum-Alloy Seamless
8244-79 : Measurement of Thickness of Anodic Coatings on Condenser & Heat-Exchanger Tubes with Integral Fins:
Aluminum & of Other Nonconductive Coatings on 1060, 3003, Alclad 3003, 5052, 5454, & 6061.
Nonmagnetic 8asis Metals with Eddy-Current
B404M-95 : Aluminum & Aluminum-Alloy Seamless
Instruments
Condenser & Heat-Exchanger Tubes with Integral Fins
B247-95a : Aluminum & Aluminum-Alloy Die Forgings, Hand [Metric]
Forgings, & Rolled Ring Forgings: 2014, 2219, 2618,
B429-95 : Aluminum-Alloy Extruded Structural Pipe & Tube:
5083,6061, 7049, 7050, 7075, & 7175 hand forgings;
6061 & 6063 extruded structural pipe & tube
1100,2014.2018,2025,2218,2219,2618,3003,
4032,5083,6061,60666151,7049,7050,7075,7076 B449-93 : Chromates on Aluminum
& 7175 die forgings; 2014, 2219, 261 FI, 6061,6151, & B457-67(1980) : Measurement of Impedance of Anodic
7075 rolled ring forgings. Coatings on Aluminum
B247M-95a : Aluminum & Aluminum-Alloy Die Forgings, B479-95 : Annealed Aluminum & Aluminum-Alloy Foil for
Hand Forgings, & Rolled Ring Forgings [Metric] Flexible Barrier Applications: 1100, 1145 & 1235.
8253-87 : Preparation of Aluminum Alloys for Electroplating B483-95 : Aluminum & Aluminum-Alloy Drawn Tubes for
826/826M-96a : Aluminum-Alloy Sand Castings General Purpose Applications: 1060, 1100, 1435,
3003,5005,5050,5052,6061,6063 & 6262.
8308/B308M-96 : Aluminum-Alloy 6061-T6 Standard
Structural Profiles (rolled or extruded) B483M-95 : Aluminum & Aluminum-Alloy Drawn Tubes for
General-Purpose Applications [Metric]
8313/B313M-95: Aluminum & Aluminum-Alloy Round
Welded Tubes: 1100, 3003, 3004, Alclad 3004, 5050, B491/B491M-95: Aluminum & Aluminum-Allay Extruded
5052,5086,5154, & 6061 round welded tube Round Tubes for General-Purpose Applications: 1050,
1100, 1200, 1235,3003 & 6063 extruded round coiled
B316/8316M-96 : Aluminum & Aluminum-Alloy Rivet &
tube
Cold-Heading Wire & Rods: 1100,2017,2024,2117,
2219,3003,5005,5052,5056,6053,6061,7050,7075 B524-92 : Concentric-lay-Stranded Aluminum Conductors,
& 7178. Aluminum-Alloy Reinforced (ACAR, 1350/6201)
8317-96: Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, & 8524M-92 : Concentric-lay-Stranded Aluminum
Structural Profiles for Electrical Purposes (Bus Conductors, Aluminum-Alloy Reinforced (ACAR,
Conductor): 6101 extruded rod, bar, structural shapes 1350/6201) [Metric]
& pipe for electrical purposes B531-90 : Aluminum-Alloy 5005 Drawing Stock for Electrical
8324 : 1350 rectangular & square wire Purposes
B327-95e1 : Master Alloys Used in Making Zinc Die Casting B547/B547M-95 : Aluminum & Aluminum-Alloy Formed &
Alloys Arc-Welded Round Tube: 1100,3003, Alclad 3003,
3004, Alclad 3004, 5050, 5052, 5083, 5086, 5154,
B345-96 : Aluminum & Aluminum-Alloy Seamless Pipe &
5454 & 6061.
Seamless Extruded Tube for Gas & Oil Transmission &
Distribution Piping Systems: 3003, 6061,6063, & 6351 B548-90: Ultrasonic Inspection of Aluminum-Alloy Plate for
seamless pipe; 1060,3003, Alclad 3003, 5083, 5086, Pressure Vessels
6061,6063, 6070, & 6351 seamless extruded tube B557-94 : Tension Testing Wrought & Cast Aluminum- &
B345M-96 : Aluminum & Aluminum-Alloy Seamless Pipe & Magnesium-Allay Products
Seamless Extruded Tube for Gas & Oil Transmission & B557M-94 : Tension Testing Wrought & Cast Aluminum- &
Distribution Piping Systems [Metric} Magnesium-Alloy Products [Metric]
B361-95: Factory-Made Wrought Aluminum & Aluminum- 8565-94 : Shear Testing of Aluminum & Aluminum-Alloy
Alloy Welding Fittings Rivets & Cold-Heading Wire & Rods
B368-85(1990)e1 : Copper-Accelerated Acetic Acid-Salt B580-79(1995) : Anodic Oxide Coatings on Aluminum
Spray (Fog) Testing (CASS Test)
B373-95 : Aluminum Foil for Capacitors :1145 & 1235
Appendix A - Standards 355
ASTM (Aluminium) - continued. 8803-94 : High-Strength Zinc-5% Aluminum-Mischmetal
8588-88 : Measurement of Thickness of Transparent or Alloy-Coated Steel Core Wire for Aluminum &
Opaque Coatings by Double-8eam Interference Aluminum-Alloy Conductors, Steel Reinforced
Microscope Technique 8807-95 : Extrusion Press Solution Heat Treatment for
8594-95: Ultrasonic Inspection of Aluminum-Alloy Wrought Aluminum Alloys
Products for Aerospace Applications B831-93: Shear Testing of Thin Aluminum Alloy Products
8597-92: Heat Treatment of Aluminum Alloys B85-96 : Aluminum-Alloy Die Castings
8603-90(1995)e1 : Drawn or Rolled Iron-Chromium- C703-72(1983) : Spalling Resistance of Porcelain Enameled
Aluminum Alloys for Electrical Heating Elements Aluminum
8606-93 : High-Strength Zinc-Coated (Galvanized) Steel D1730-67(1984)e1 : Preparation of Aluminum & Aluminum-
Core Wire for Aluminum & Aluminum-Alloy Conductors, Alloy Surfaces for Painting
Steel Reinforced D1731-67(1984)e1 : Preparation of Hot-Dip Aluminum
8609: Aluminum 1350 round wire, annealed & intermediate Surfaces for Painting
tempers, for electrical purposes D2570-96 : Simulated Service Corrosion Testing of Engine
8618-96: Aluminum-Alloy Investment Castings Coolants
B632/B632M-95 : Aluminum-Alloy Rolled Tread Plate: 6061 D2651-90 : Preparation of Metal Surfaces for Adhesive
B645-95: Plane-Strain Fracture Toughness Testing of Bonding
Aluminum Alloys D2674-72(1984) : Analysis of Sulfochromate Etch Solution
8646-94 : Fracture Toughness Testing of Aluminum Alloys Used in Surface Preparation of Aluminum
8647-84: Indentation Hardness of Aluminum Alloys by D2773-94 : Test Method for Loss on Ignition of Electrical
Means of a Webster Hardness Gage Grade Magnesium Oxide (10.01).
B648-78(1984)e1 : Indentation Hardness of Aluminum D2809-94 : Cavitation Corrosion & Erosion-Corrosion
Alloys by Means of a Barcollmpressor Characteristics of Aluminum Pumps With Engine
8659-90 : Measuring Thickness of Metallic & Inorganic Coolants
Coatings D2847-94 : Testing Engine Coolants in Car & Light Truck
B660-96 : Packaging/Packing of Aluminum & Magnesium Service
Products D3115-95 : Explosive Reactivity of Lubricants with
B666/B666M-96 : Identification Marking of Aluminum & Aerospace Alloys Under High Shear
Magnesium Products D3933-93 : Preparation of Aluminum Surfaces for Structural
8669-95a : Zinc-Aluminum Alloys in Ingot Form for Foundry Adhesives 80nding (Phosphoric Acid Anodizing)
& Die Castings D4340-96 : Corrosion of Cast Aluminum Alloys in Engine
B680-80(1989) : Seal Quality of Anodic Coatings on Coolants Under Heat-Rejecting Conditions
Aluminum by Acid Dissolution D4628-96 : Analysis of Barium, Calcium, Magnesium, and
B681-88: Measurement of Thickness of Anodic Coatings on Zinc in Unused Lubricating Oils.
Aluminum & of Other Transparent Coatings on Opaque
D5502-94 : Test Method for Apparent Density by Physical
Surfaces Using the Light-Section Microscope
Measurements of Manufactured Anodes.
8686-96a : Aluminum Alloy Castings, High-Strength
D930-89(1996)e1 : Total Immersion Corrosion Test of
B724-83(1991 )e1 : Indentation Hardness of Aluminum Water-Soluble Aluminum Cleaners
Alloys by Means of a Newage Portable Non-Caliper-
E 101-91 : Spectrographic Analysis of Aluminum &
Type Instrument
Aluminum Alloys by the Point-to-Plane Technique
8736-95 : Aluminum, Aluminum Alloy & Aluminum-Clad
E1004-91 : Electromagnetic (Eddy-Current) Measurements
Steel Cable Shielding Stock
of Electrical Conductivity
8750-94a : Zinc-5% Aluminum-Mischmetal Alloy (UNS
E1251-94 : Optical Emission Spectrometric Analysis of
Z38510) in Ingot Form for Hot-Dip Coatings
Aluminum & Aluminum Alloys by the Argon
8753-86(1993)e1 : Thermostat Component Alloys Atmosphere, Point-to-Plane, Unipolar Self-Initiating
8769-94 : Shear Testing of Aluminum Alloys Capacitor Discharge
8788-94 : Installing Factory-Made Corrugated Aluminum E1338-90 : The Identification of Metals & Alloys in
Culverts & Storm Sewer Pipe Computerized Material Property Databases
878-90(1995)e1 : Accelerated Life of lron-Chromium- E155-95e1 : Inspection of Aluminum & Magnesium Castings
Aluminum Alloys for Electrical Heating
E1637-94: Specification for Structural Standing Seam
8789-96 : Installing Corrugated Aluminum Structural Plate Aluminum Roof Panel Systems (04.11).
Pipe for Culverts & Sewers
E164-94a : Ultrasonic Contact Examination of Weldments
8791-96: Zinc-Aluminum (ZA) Alloy Foundry & Die
E1793-96 : Preparation of Aluminum Alloy for Bonding in
Castings
Foam & Beam Type Transportable Shelters
B800-94 : 8000 Series Aluminum Alloy Wire for Electrical
E1794-96: Adhesive for Bonding Foam Cored Sandwich
Purposes-Annealed & Intermediate Tempers
Panels (200F Elevated Humidity Service), Type /I
B801-95 : Concentric-lay-Stranded Conductors of 8000 Panels
Series Aluminum Alloy for Subsequent Covering or
E1800-96 : Adhesive for Bonding Foam Cored Sandwich
Insulation
Panels (160F Elevated Humidity Service), Type I
Panels
356 Appendix A - Standards
ASTM (Aluminium) - continued. G34-97 Exfoliation Corrosion Susceptibility in 2XXX &
E1801-96 Adhesive Bonding of Aluminum Facings in Foam 7XXX Series Aluminum Alloys (EXCO Test)
& Beam Type Shelters G44-94 Evaluating Stress Corrosion Cracking Resistance
E1826-96 Low Volatile Organic Compound (VOC) of Metals & Alloys by Alternate Immersion in 3.5%
Corrosion-Inhibiting Adhesive Primer for Aluminum Sodium Chloride Solution
Alloys to Be Adhesively Bonded. G64-91 Resistance to Stress-Corrosion Cracking of Heat-
E215-87(1992)e1 Standardizing Equipment for Treatable Aluminum Alloys
Electromagnetic Examination of Seamless Aluminum- G66-95 Visual Assessment of Exfoliation Corrosion
Alloy Tube Susceptibility of 5XXX Series Aluminum Alloys (ASSET
E227-90. Optical Emission Spectrometric Analysis of Test)
Aluminum & Aluminum Alloys by the Point-to-Plane G67-93. Determining the Susceptibility to Intergranular
Technique Corrosion of 5XXX Series Aluminum Alloys by Mass
E252-84 Thickness of Thin Foil & Film by Weighing Loss After Exposure to Nitric Acid (NAML T Test)
E262-86e1 Determining Thermal Neutron Reaction & G69-81 (1994)e1 Measurement of Corrosion Potentials of
Fluence Rates by Radioactivation Techniques Aluminum Alloys
E34-94 Chemical Analysis of Aluminum & Aluminum-Base G82-83e1 Development & Use of a Galvanic Series for
Alloys Predicting Galvanic Corrosion Performance
E428-92 Fabrication & Control of Steel Reference Blocks
Used in Ultrasonic Inspection AMS - Aerospace Material SpeCifications
E505-96 Inspection of Aluminum & Magnesium Die 2201 Tolerances for rolled, drawn, cold-finished, &
Castings centerless ground wire, rod, bar & forging stock
E602-91 Sharp-Notch Tension Testing with Cylindrical 2202 Tolerances for sheet & plate
Specimens
2203 Tolerances for drawn tube
E607-90 Optical Emission Spectrometric Analysis of
2204 Tolerances for rolled or extruded standard structural
Aluminum & Aluminum Alloys by the Point-to-Plane
shapes
Technique, Nitrogen Atmosphere
2205 Tolerances for extruded rod, bar, shapes, & tube
E716-94 Sampling Aluminum & Aluminum Alloys for
Spectrochemical Analysis 2468 Hard-coating of aluminum alloys
E749-96 Acoustic Emission Monitoring During Continuous 2469 Process & performance requirements for hard-
Welding coating
E864-96 Surface Preparation of Aluminum Alloys to be 2470. Chromic-acid anodizing of aluminum alloys
Adhesively Bonded in Honeycomb Shelter Panels 2471 Clear sulfuric-acid anodizing of aluminum alloys bar
E866-96 Corrosion-Inhibiting Adhesive Primer for 2472 Dyed sulfuric-acid anodizing of aluminum alloys
Aluminum Alloys to Be Adhesively Bonded in 2473. Chemical conversion treatments for aluminum alloys
Honeycomb Shelter Panels
2474. Low electrical resistivity chemical conversion
E874-96. Practice for Adhesive Bonding of Aluminum treatments for aluminum alloys
Facings to Nonmetallic Honeycomb Core. 2808 Identification markings of forgings
F1077-95a. Selection of Committee F-16 Fastener 2816 Color code identification marking of welding wire
Specifications
4001 1100-0 sheet & plate
F 111 0-90 Sandwich Corrosion Test
4003 11 OO-H 14 sheet & plate
F467-93. Nonferrous Nuts for General Use
4004. 5052-H191 foil
F467M-93 Nonferrous Nuts for General Use [Metric]
4005. 5056-H191 foil
F468-93 Nonferrous Bolts, Hex Cap Screws, & Studs for
4006 3003-0 sheet & plate
General Use
F468M-93 Nonferrous Bolts, Hex Cap Screws, & Studs for 4007 2024-0 foil
General Use [Metric] 4008. 3003-H14 sheet & plate
G1 00-89(1994)e Conducting Cyclic Galvanostaircase 4009.6061-0 foil
Polarization 4010 3003-H18 foil
G102-89(1994)e1 Calculation of Corrosion Rates & 4011 1145-0 foil
Related Information from Electrochemical 4013 Laminated shim stock, surface bonded
Measurements
4015 5052-0 sheet & plate
G103-8ge1 Performing a Stress-Corrosion Cracking Test
of Low Copper Containing AI-Zn-Mg Alloys in Boiling 4016 5052-H32 sheet & plate
6% Sodium Chloride Solution 4017 5052-H34 sheet & plate
G110-92 Evaluating Intergranular Corrosion Resistance of 4021 Alclad 6061- sheet & plate
Heat Treatable Aluminum Alloys by Immersion in 4024. 7075-T6 & T651 sheet & plate
Sodium Chloride + Hydrogen Peroxide Solution
4025 6061-0 sheet & plate
G 112-92 Conducting Exfoliation Corrosion Tests in
Aluminum Alloys 4026. 6061-T4 & T451 sheet & plate
G 139-96 Determining Stress-Corrosion Cracking 4027. 6061-T6 & T651 sheet & plate
Resistance of Heat-Treatable Aluminum Alloy Products 4028.2014-0 sheet & plate
Using Breaking Load Method 4029. 2014-T6 & T651 sheet & plate
Appendix A - Standards 357
AMS (Aluminium) - continued. 4118: 2017-T4 & T451 rolled, drawn, or cold finished wire,
4035 : 2024-0 sheet & plate rod & bar
4036: Alclad one side 2024-T3 sheet & T351 plate 4120: 2024-T4 & T351 rolled, drawn, or cold finished wire,
rod & bar
4037 : 2024-T3 sheet & T351 plate
4121 : 2014-T6 rolled, drawn or cold finished wire, rod & bar
4040 : Alclad 2024-0 sheet & plate
4122: 7075-T6 rolled or cold finished wire, rod & bar
4044 : 7075-0 sheet & plate
4123 : 7075-T651 rolled or cold finished rod & bar
4045: 7075-T6 sheet & T651 plate
4124 : 7075-T7351 rolled or cold finished bar
4046: Alclad one side 7075-T6 sheet & T651 plate
4125: 6151-T6 forgings
4048 : Alclad 7075-0 sheet & plate
4126 : 7075-T6 forgings & 7075-F forging stock
4049: Alclad 7075-T6 sheet & T651 plate
4127: 6061-T6 die forgings & rolled rings & 6061-F forging
4050 : 7050-T7 451 (formerly T73651) plate
stock
4054 : Brazing sheet No. 21-0
4128: 6061-T451 rod & bar, rolled or cold finished
4055 : Brazing sheet No. 22-0
4130 : 2025-T6 forgings
4056 : 5083-0 sheet & plate
4131 : 7075-T736 forgings
4062 : 11 OO-H 14 drawn tube 4132 : 2618-T61 forgings
4063 : Brazing sheet No. 11-0
4133: 2014-T6 forgings & 2014 forging stock
4064 : Brazing sheet No. 12-0
4134: 2014-T4 forgings
4065 : 3003-0 drawn tube, seamless
4140: 2018-T61 forgings
4066: 2219-T851 drawn tube, seamless
4141 : 7075-T73 die forgings & forging stock
4067 : 3003-H14 drawn tube, seamless
4142: 2218-F forgings
4068 : 2219-T351 drawn tube, seamless
4143: 2219-T6 forgings
4069 : 5052-0 drawn tube, special tolerances, seamless
4144: 2219-T852 forgings
4070. : 5052-0 drawn tube, seamless 4146: 6061-T4 die forgings & rolled rings & 6061-F forging
4071 : 5052-0 drawn, hydraulic tube, seamless stock
4077 : Alclad one side 2024-0 sheet & plate 4147: 7075-T7352 forgings
4078 : 7075-T7351 plate 4148: 7175-T66 die forging
4079 : 6061-0 drawn tube, special tolerances 4149 : 7175-T7 4 die & hand forgings
4080: 6061-0 drawn tube 4150: 6061-T6 extruded wire, rod, bar, shapes & tube
4081 : 6061-T 4 drawn, hydraulic tube 4152: 2024-T3 extruded wire, rod, bar, shapes & tube
4082: 6061-T6 drawn tube 4153 : 2014-T6 extruded wire, rod, bar, shapes & tube
4083 : 6061-T6 drawn, hydraulic tube 4154: 7075-T6 extruded wire, rod, bar, shapes & tube
4084: 7475-T61 sheet 4156 : 6063-T6 extruded wire, rod, bar, & shapes
4085: 7475-T761 sheet 4157 : 7049-T73511 extrusion
4086 : 2024-T3 drawn, hydraulic tube 4159: 7049-T76511 extrusion
4087 : 2024-0 drawn tube 4160: 6061-0 extruded wire, rod, bar, shapes & tube
4088: 2024-T3 drawn tube 4161 : 6061-T4 extruded wire, rod, bar, shapes & tube
4089: 7475-T7631 plate 4162: 2219-T8511 extruded wire, rod, bar, shapes & tube
4090: 7475-T761 plate 4163: 2219-T3511extruded wire, rod, bar, shapes & tube
4094: Alclad 2219-T81 sheet & T851 plate 4164: 2024-T3510 extruded wire, rod, bar, shapes & round
4095: Alclad 2219-T31 sheet & T351 plate tube
4096 : Alclad 2219-0 sheet & plate 4165: 2024-T3511 extruded wire, rod, bar, shapes, & round
tube
4100: Alclad 7475-T761 sheet
4166: 7075-T73 extruded wire, rod, bar, shapes & tube
4101 : 2124-T851 plate
4167: 7075-T73511 extruded wire, rod, bar & shapes
4102 : 11 OO-F rolled or cold-finished wire, rod & bar
4168: 7075-T6510 extruded wire, rod, bar, shapes, & round
4107 : 7050-T7 4 (formerly T736) die forgings
tube
4108 : 7050-T7 452 (formerly T73652) hand forgings
4169 : 7075-T6511 extruded wire, rod, bar, shapes, & round
4111 : 7049-T73 forgings & forging stock tube
4112 : 2024-T6 rolled, drawn, or cold-finished wire, rod & 4172: 6061-T4511 extruded rod, bar, shapes & tube
bar
4173 : 6061-T6511 extruded rod, bar, shapes & tube
4113 : 6061-T6 structural shapes
4179 : 7175-T7 452 hand forgings & forging stock
4114 : 5052-F rolled or cold-finished wire, rod & bar
4180 : 11 OO-H 18 wire for metal spraying
4115 : 6061-0 rolled, drawn, or cold finished wire, rod & bar
4182 : 5056-0 wire
4116: 6061-T4 rolled or cold finished wire, rod & bar
4184 : 4145 brazing metal
4117 : 6061-T6 & T651 roiled, drawn, or cold finished wire,
4185 : 4047 brazing metal
rod & bar
358 Appendix A - Standards
AMS (Aluminium) - continued. ANSI/AAMA
4186 : 7075-F wire, rod & bar; rolled, drawn or cold finished
ANSIlAAMA 101-1993: Aluminum and PVC
4187: 7075-0 wire, rod & bar rolled, drawn or cold finished (PolyVinyIChloride) Prime Windows & Glass Doors.
4190 : 4043-F welding wire & rod ANSIlAAMA 1102.7-1989 : Aluminum Storm Doors.
4191 : 2319-F welding wire & rod ANSIlAAMA 1402-1986: Standard Specifications for
4192: 2024-T361 sheet & plate Aluminum Siding, Soffit & Fascia.
4193 : 2024-T861 sheet & plate
ANSI/ASME
4194: Alclad 2024-T361 sheet & plate
ANSIIASME B96.1-1993 : Welded Aluminum-Alloy Storage
4195 : Alclad 2024-TB61 sheet & plate
Tanks (includes revision service).
4196 : 7011 Alclad 7075-0 sheet & plate
ANSIIASSE 1045-1990: Aluminum Drain, Waste, and Vent
4197 : 7011 Alclad 7075-T6 sheet & T651 plate Pipe with End Cap Components.
4200: 7049-T7351 plate
ANSI/AWS
4201 : 7050-T7651 plate
4202: 7475-T731 plate ANSIIAWS A5.1 0-92 : Bare Aluminum and Aluminum Alloy
Welding Electrodes and Rods, Specification.
4207: Alclad 7475-T61 sheet
ANSIIAWS A5.3-91 : Aluminum and Aluminum Alloy
4243 : Alclad 7050-T76 sheet
Electrodes for Shielded Metal Arc Welding.
4247: 7049-T7352 hand forging
ANSIIAWS C2.18-93: Protection of Steel with Thermal
4248: 6061 -T652 forgings Sprayed Coatings of Aluminum and Zinc, etc.
4310: 7075-T651 & T652 rings, forged or rolled ANSIIAWS C3.7-93: Specification for Aluminum Brazing.
4311 : 7075-T7351 rings, forged or rolled ANSIIAWS D1.2-90 : Structural Welding Code - Aluminum
4312: 6061-T651 rings, rolled or forged (includes ANSIIAWS D1.2A-83, Commentary).
4313: 2219-T351 & T352 rings, forged or rolled ANSI/AWS D10.7-86 (R1992) : Gas Shielded Arc Welding
of Aluminum and Aluminum Alloy Pipe, Recommended
4314 : 2014-T651 rings, forged or rolled
Practice
4321 : 7049-0 forgings
ANSIIAWS D3.7-90: Guide for Aluminum Hull Welding.
4323: 7075-T7452 hand forged
4333: 7050-T742 die forgings ANSI/IEEE
4340: 7050-T76511 extrusions ANSI/IEEE 635-1989 (R1994) : Guide for Selection and
4341 : 7050-T73511 extrusions DeSign of Aluminum Sheaths for Power Cables.
4342: 7050-T74511 (formerly T736511) extrusions
ANSIINFPA
4344 : 7175-T73511 extrusions
ANSI/NFPA 651-1993: Manufacture of Aluminum and
7220: 1100-H14 rivets
MagneSium Powder.
7222: 2117-T4 rivet
ANSI/NFPA 65-1993: Processing and Finishing of
7223 : 2024-T4 rivets Aluminum.
ANSI/SAE MA SAE/AMS
ANSI/SAE MA 2152/1 : Clamp, Center Mount, Bare Metal, Note: * denotes that a standard has been cancelled or
Aluminum, Metric. superseded as a result of technical committee action;
ANSI/SAE MA 2153/1 : Clamp, Loop Type, Bare Metal, photocopies are available from SAE.
Aluminum, Metric. SAE/AMS 4000E (Jul-76) Aluminum Sheet & Plate (1060-0)
ANSI/SAE MAM SAE/AMS 4001 G (Jul-91) Aluminum Sheet & Plate 0.12Cu
(1100-0) Annealed
ANSI/SAE MAM 2201 : Tolerances, Metric, Aluminum and SAE/AMS 4003G (Sep-95) Aluminum Alloy, Sheet & Plate
Aluminum Alloy Bar, Rod, Wire, and Forging St. 0.12Cu (1100-H14) Strain Hardened
ANSI/SAE MAM 2202A : Metric, Aluminum Alloy and SAE/AMS 4004C (Sep-95) Aluminum Alloy, Foil 2.5 Mg
Magnesium Alloy Sheet and Plate. 0.25Cr (5052-H191) Strain Hardened
ANSI/SAE MAM 2204A: Tolerances, Metric Aluminum Alloy SAE/AMS 4005C (Jul-89) Aluminum Alloy, Foil, 5.0Mg
Standard Structural Shapes.
0.12Mn 0.12Cr, Strain Hardened
ANSI/SAE MAM 2355B : Quality Assurance Sampling and SAE/AMS 4006G (Jul-90) Aluminum Alloy, Sheet & Plate,
Testing of Aluminum Alloys and Magnesium Alloy.
1.25Mn 0.12Cu (3003-0), Annealed
ANSI/SAE MAM 2771 : Heat Treatment of Aluminum Alloy SAE/AMS 4007C (Apr-87) Aluminum Alloy, Foil 4.4Cu
Castings.
1.5Mg 0.60Mn
ANSI/SAE MAM 4208A : Aluminum Alloy Sheet - (2004-F),
SAE/AMS 4008H (Sep-94) Aluminum Alloy, Sheet & Plate,
As Rolled. 1.25Mn 0.12Cu, Strain Hardened
ANSI/SAE MAM 4209A : Aluminum Alloy Sheet, Alclad, SAE/AMS 4009A (Oct-91) Aluminum Alloy, Foil 1.0Mg 0.6Si
6.0Cu - OAOZr (2004-F), As Rolled (revision)
0.30Cu 0.20Cr Annealed
ANSI/SMA SAE/AMS 4010B (Jan-77) Foil, 1.2Mn 0.12Cu
SAE/AMS 4011 B (Feb-95) Aluminum, Foil & Light Gage
ANSI/SMA 1004-1987 : Aluminum Tubular Frame Screens
Sheet, 99.45AI (1145-0) Annealed
for Windows, Specifications.
SAE/AMS 4012F (Apr-87) Aluminum Sheet, Laminated,
ANSI/SMA 2006-1987: Aluminum Sliding Screen Doors,
Edge Bonded
Specifications for.
SAE/AMS 40130 (Jul-91) Aluminum Sheet, Laminated,
ANSI/SMA 3001-1987: Aluminum Swinging Screen Doors,
Surface Bonded
Specifications.
SAE/AMS 4014B (Invalid D) Aluminum Alloy, Plate 4.5Cu
ANSI/UL 0.85Si 0.80Mn 0.50Mg*
ANSI/UL 486B-1990 : Wire Connectors for Use With SAE/AMS 4015J (Sep-94) Aluminum Alloy, Sheet & Plate,
Aluminum Conductors. 2.5Mg 0.25Cr Annealed
ANSI/UL 486E-1994: Equipment Wiring Terminals for Use SAE/AMS 4016J (Jul-94) Aluminum Alloy, Sheet & Plate,
with Aluminum and/or Copper Conductors. 2.5Mg 0.25Cr (5052-H32), Strain Hardened, Quarter-
Hard, & Stabilized
SAE/AMS 4017J (Oct-91) Aluminum Alloy, Sheet & Plate,
SAE Standards 2.5Mg 0.25Cr, Strain-Hardened, Half-Hard, &
Stabilized
SAE MAM
SAE/AMS 4018C (Invalid D) Aluminum Alloy, Sheet & Plate
SAE MAM 4131A (Nov-96) Aluminum Alloy, Die & Hand 3.5Mg 0.25Cr*
Forgings 5.6Zn 2.5Mg 1.6Cu 0.23Cr Solution Heat SAE/AMS 4019B (Invalid D) Aluminum Alloy, Sheet & Plate
Treated & Aged 3.5Mg 0.25Cr*
SAE MAM 4141A (Jul-90) Aluminum Alloy, Die Forgings, SAE/AMS 4020B (Invalid D) Aluminum Alloy, Plate, Alclad
5.6Zn 2.5Mg 1.6Cu 0.23Cr Solution & Precipitation 1.0Mg 0.60Si 0.28Cu 0.25Cr*
Heat Treated
SAE/AMS 4021 F (Oct-93) Aluminum Alloy, Alclad Sheet &
SAE MAM 4208A (Apr-90) Aluminum Alloy, Sheet, 6.0Cu Plate, 1.0Mg 0.60Si 0.28Cu 0.20Cr (Alclad 6061-0)
0.40Zr, As Rolled Annealed
SAE MAM 4209A (Oct-90) Aluminum Alloy, Sheet, Alclad, SAE/AMS 4022F (Jan-77) Aluminum Alloy Sheet & Plate,
6.0Cu 0.40Zr, As Rolled Alclad, 1.0Mg 0.60Si 0.28Cu 0.20Cr*
360 Appendix A - Standards
SAE/AMS (Aluminium) - continued. SAE/AMS 4049H (Apr-S7) Aluminum Alloy, Sheet & Plate,
SAE/AMS 4023E (Jan-77) Sheet & Plate, Alclad, 1.0Mg Alclad, 5.6Zn 2.5Mg 1.6Cu 0.23Cr Solution &
0.60Si O.2SCu O.2SCr Precipitation Heat Treated
SAE/AMS 4024C (Invalid 0) Aluminum Alloy, Sheet & Plate SAE/AMS 4050E (Jul-92) Aluminum Alloy, Plate 6.2Zn
4.3Zn 3.3Mg 0.60Cu 0.20Mn O. 17Cr (7079:-T6Sheet, - 2.3Cu 2.2Mg O. 12Zr Solution Heat Treated, Stress
T651 Plate)* Relieved, & Overaged
SAE/AMS 4025J (Jul-94) Aluminum Alloy, Sheet & Plate, SAE/AMS 4051 E (Apr-85) Aluminum Alloy, Sheet & Plate,
1.0Mg 0.60Si 0.2SCu 0.20Cr Annealed Alclad 6.SZn 2.SMg 2.0Cu 0.23Cr Annealed
SAE/AMS 4026K (Aug-96) Aluminum Alloy, Sheet & Plate SAE/AMS 4052A (Invalid D) Cancelled Jul. 1981*
1.0Mg 0.60Si O.2SCu 0.20Cr Solution Heat Treated & SAE/AMS 4053B (Invalid D) Aluminum Alloy, Plate 1.0Mg
Naturally Aged 0.60Si O.2SCu 0.25Cr*
SAE/AMS 4027L (Oct-93) Aluminum Alloy, Sheet & Plate, SAE/AMS 4054C (Invalid D) Aluminum Alloy, Sheet, Clad
1.0Mg 0.60Si 0.2SCu 0.20Cr (6061; -T6 Sheet, -T651 One Side, 0.6Mg-0.35Si-0.28Cu (No. 21-0 Brazing
Plate), Solution & Precipitation Heat Treated Sheet)*
SAE/AMS 402SF (Oct-91) Aluminum Alloy, Sheet & Plate SAE/AMS 40550 (Invalid D) Aluminum Alloy, Sheet, Clad
4.4Cu 0.85Si 0.80Mn 0.50Mg, Annealed Two Sides 0.6Mg-0.35Si-0.28Cu (No. 22-0 Brazing
SAE/AMS 4029H (Jan-92) Aluminum Alloy, Sheet & Plate Sheet) Annealed'
4.5Cu 0.85Si 0.80Mn 0.50Mg Solution & Precipitation SAE/AMS 4056F (Nov-94) Aluminum Alloy, Sheet & Plate,
Heat Treated 4.4Mg 0.70Mn O. 15Cr, Annealed
SAE/AMS 4030C (Jun-49) Aluminum Alloy, Sheet & Plate SAE/AMS 4057E (Jul-77) Aluminum Alloy, Sheet 4.4Mg-
Copper Manganese Magnesium (17 Solo O. 70Mn-0. 15Cr (50S3-H323)*
SAE/AMS 4031 E (Oct-93) Aluminum Alloy, Sheet & Plate SAE/AMS 4058E (Jul-77) Aluminum Alloy, Sheet 4.4Mg-
6.3Cu 0.30Mn 0 18Zr 0 10V 0.06Ti (2219-0) Annealed O. 70Mn-0. 15Cr (5083-373)*
SAE/AMS 4032C (Jun-49) Aluminum Alloy, Sheet & Plate SAE/AMS 4059F (Jul-77) Sheet & Plate - 4.4Mg 0.70Mn
Copper Manganese Magnesium (17 S-T)* 0.15Cr*
SAE/AMS 4033C (Invalid D) Aluminum Alloy, Plate 4.4Cu SAE/AMS 4061 (Invalid D) Aluminum Alloy, Sheet & Plate,
1.5Mg 0.60Mn* Alclad 4.5 Cu - 1.5 Mg - 0.60 Mn - (Alclad 2024-T36)
SAE/AMS 4034C (Invalid D) Aluminum Alloy, Plate, Alclad Width over 60 Inches*
4.4Cu 1.5Mg 0.60M* SAE/AMS 4062G (Apr-89) Aluminum Tubing, Seamless,
SAE/AMS 4035J (Sep-96) Aluminum Alloy, Sheet & Plate Drawn, Round, Strain Hardened
4.4Cu 1.5Mg 0.60Mn (2024-0) Annealed SAE/AMS 4063C (Oct-93) Aluminum Alloy, Clad One Side
SAE/AMS 4036H (Oct-93) Aluminum Alloy, Sheet & Plate, Sheet, 1.25Mn 0.12Cu (No. 11-0 Brazing Sheet),
Alclad One Side 4.4Cu 1.5Mg 0.60Mn Alclad One Side Annealed
2024 & 1-1/2% Alcald One Side 2024-T3 Sheet; 1- SAE/AMS 40640 (Nov-95) Aluminum Alloy, Clad Two Sides
1/2% Alclad One Side 2024-T351 Plate Sheet, 1.25Mn O. 12Cu (No. 12-0 Brazing Sheet),
SAE/AMS 4039C (Invalid D) Superseded by*SAE/AMS Annealed
403SC (Invalid D) Superseded by*SAE/AMS 4037M SAE/AMS 4065G (Oct-S6) Aluminum Alloy, Tubing,
(Jan-93) Aluminum Alloy, Sheet & Plate 4.4Cu 1.5Mg Seamless, Drawn 1.2Mn-0.12Cu (3003-0) Annealed
0.60Mn Solution Heat Treated SAE/AMS 4066B (Oct-93) Aluminum Alloy, Drawn, Round
SAE/AMS 4040L (Mar-95) Aluminum Alloy, Alclad Sheet & Seamless Tubing 6.3Cu 0.30Mn O. 1SZr 0.1 OV 0.06Ti
Plate, 4.4Cu 1.5Mg 0.60Mn, Annealed (2219-T8511), Solution Heat Treated, Stress Relieved
SAE/AMS 4041 N (Oct-93) Aluminum Alloy, Sheet Plate, by Stretching, & Precipitation Heat Treated
Alclad 4.4Cu 1.5Mg 0.60Mn Alclad 2024 & 1-1/2% SAE/AMS 4067G (Oct-93) Aluminum Alloy, Drawn Round
Alclad 2024, -T3 Flat Sheet; 1-1/2% Alclad 2024-T351 Seamless Tubing 1.25Mn 0.12Cu (3003-H14) Strain
Plate Hardened
SAE/AMS 4042F (Invalid D) Aluminum Alloy, Sheet & Plate, SAE/AMS 406SC (Apr-97) Aluminum Alloy, Drawn
Alclad 4.5Cu 1.5Mg 0.60Mn Width 48 in. & Under* Seamless Tubing 6.3Cu 0.30Mn O. 1SZr 0.1 OV 0.06Ti
SAE/AMS 4043B (Invalid D) Aluminum Alloy, Plate 1.0Mg (2219-T3511), Solution Heat Treated & Stress
0.60Si O.2SCu 0.25Cr* Relieved by Stretching
SAE/AMS 4044H (Jul-94) Aluminum Alloy, Sheet & Plate, SAE/AMS 4069C (Sep-95) Aluminum Alloy, Drawn, Round
5.6Zn 2.5Mg 1.6Cu 0.23Cr, Annealed Seamless Tubing Close Tolerance 2.5Mg 0.25Cr
(5052-0) Annealed
SAE/AMS 4045H (Jan-93) Aluminum Alloy, Sheet & Plate
5.6Zn 2.5Mg 1.6Cu 0.23Cr Solution & Precipitation SAE/AMS 4070K (Sep-95) Aluminum Alloy, Drawn, Round
Heat Treated Seamless Tubing 2.5Mg 0.25Cr (5052-0) Annealed
SAE/AMS 4046E (Oct-91) Aluminum Alloy, Sheet & Plate, SAE/AMS 4071 K (Sep-95) Aluminum Alloy, Drawn, Round,
Alclad One Side 5.6Zn 2.5Mg 1.6Cu 0.23Cr Solution & Seamless Hydraulic Tubing 2.5Mg 0.25Cr (5052-0)
Precipitation Heat Treated Annealed
SAE/AMS 4047B (Oct-S1) Aluminum Alloy, Sheet & Plate, SAE/AMS 4072 (Jul-81) Aluminum Alloy, Sheet & Plate,
Aluminum Alloy Clad, Roll Tapered 5.6Zn 2.5Mg 1.6Cu Alclad 4.5Cu 1.5Mg 0.60Mn (Alclad 2024-TS6) Width
0.25Cr (Alclad 7075-T6)* 30 In. & Under*
SAE/AMS 404SH (Apr-S9) Aluminum Alloy, Sheet & Plate, SAE/AMS 4073 (Jul-81) Aluminum Alloy, Sheet & Plate,
Alclad, 5.6Zn 2.5Mg 1 .6Cu 0.23Cr, Annealed Alclad 4.5 Cu - 1.5 Mg - 0.60 Mn - (Alclad 2024-T86)
Width over 30 to 48 In., Incl.*
Appendix A - Standards 361
SAE/AMS (Aluminium) - continued. SAE/AMS 4095B (Oct-93) Aluminum Alloy, Sheet & Plate,
SAE/AMS 4074 (Jul-81) Aluminum Alloy, Sheet & Plate, Alclad 6.3Cu 0.30Mn 0.18Zr 0.10V 0.06Ti, Alclad 2219
Alclad 4.5 Cu - 1.5 Mg - 0.60 Mn - (Alclad 2024-T86) T31; Sheet, Solution Heat Treated & Cold Worked
Width over 30 to 48 In., Incl.* Alclad 2219-T351; Plate, Solution Heat Treated &
Stress Relieved
SAE/AMS 4075 (Jul-81) Aluminum Alloy, Sheet & Plate,
Alclad 4.5 Cu - 1.5 Mg - 0.60 Mn - (Alclad 2024-T86) SAE/AMS 4096A (Apr-84) Sheet & Plate, Alclad - 6.3Cu
Width over 60 In.* 0.30Mn 0.18Zr 0.10V 0.06Ti, Annealed
SAE/AMS 4076B (Feb-49) Aluminum AllOy, Tubing SAE/AMS 4097 (Invalid D) Aluminum Alloy, Sheet & Plate
(Seamless) Magnesium Silicon Chromium (53S-W)* 4.5 Cu - 1.5 Mg - 0.60 Mn (2024-T36) Width 48 In. &
Under*
SAE/AMS 4077E (Oct-91) Aluminum AllOy, Sheet & Plate,
Alclad One Side 4.4Cu 1.5Mg 0.60Mn Annealed SAE/AMS 4098 (Invalid D) Aluminum Alloy, Sheet & Plate
4.5 Cu - 1.5 Mg - 0.60 Mn (2024-T36) Width over 48 to
SAE/AMS 4078E (Jul-92) Aluminum Alloy, Plate 5.6Zn
60 In., Incl:
2.5Mg 1.6Cu 0.23Cr Solution Heat Treated, Stress
Relieved, & Overaged SAE/AMS 4099 (Invalid D) Aluminum Alloy, Sheet & Plate
4.5 Cu - 1.5 Mg - 0.60 Mn (2024-T36) Width over 60
SAE/AMS 4079E (May-96) Aluminum Alloy, Drawn, Round,
In:
Seamless, Tubing 1.0Mg 0.06Si 0.28Cu 0.20Cr Close
Tolerance, Annealed SAE/AMS 4100B (Apr-93) Aluminum Alloy, Sheet, Alclad,
5.7Zn 2.2Mg 1.6Cu 0.22Cr Solution & Precipitation
SAE/AMS 4080L (May-96) Aluminum Alloy, Drawn,
Heat Treated
Seamless Tubing 1.0Mg 0.60Si 0.28Cu 0.20Cr,
Annealed SAE/AMS 4101 B (Mar-95) Aluminum Alloy, Plate, 4.4Cu
1.5Mg 0.60Mn, Solution Heat Treated, Stretched, &
SAE/AMS 4081G (Jan-93) Aluminum Alloy, Tubing,
Precipitation Heat Treated
Hydraulic, Seamless, Drawn, Round 1.0Mg 0.60Si
0.28Cu 0.20Cr Solution Heat Treated & Naturally Aged SAE/AMS 4102F (Oct-90) Aluminum Alloy, Bars, Rods, &
Wire, Rolled or Cold-Finished 99.0A 1, As Fabricated
SAE/AMS 4082M (Dec-94) Aluminum Alloy, Seamless
Drawn Tubing, 1.0Mg 0.60Si 0.28Cu 0.20Cr Solution & SAE/AMS 4103 (Invalid D) Aluminum Alloy, Sheet & Plate
Precipitation Heat Treated 4.5Cu 1.5Mg 0.60Mn (2024-T36) Width 30 In. & Under*
SAE/AMS 4083J (Jan-93) Aluminum Alloy, Tubing, SAE/AMS 4104 (Invalid D) Aluminum Alloy, Sheet & Plate
Hydraulic, Seamless, Drawn, Round, 1.0Mg 0.60Si 4.5Cu 1.5Mg 0.60Mn (2024-T36) Width over 30 to 48
0.28Cu 0.20Cr Solution & Precipitation Heat Treated In., Incl.*
SAE/AMS 4084C (Jul-90) Aluminum Alloy, Sheet 5.7Zn SAE/AMS 4105 (Jul-81) Aluminum Alloy, Sheet & Plate
2.2Mg 1.6Cu 0.22Cr Solution & Precipitation Heat 4.5Cu 1.5Mg 0.60Mn (2024-T86) Width over 48 to 60
Treated In.,lncl.*
SAE/AMS 4085B (Jan-86) Aluminum Alloy, Sheet 5. 7Zn SAE/AMS 4106 (Jul-81) Aluminum Alloy, Sheet & Plate
2.2Mg 1.6Cu 0.22Cr Solution Heat Treated & 4.5Cu 1.5Mg 0.60Mn (2024-T86) Width over 60
Overaged Inches*
SAE/AMS 4086M (Nov-96) Aluminum Alloy, Drawn. Round, SAE/AMS 4107D (Apr-92) Aluminum Alloy, Die Forgings
Seamless Hydraulic Tubing, 4.4Cu 1.5Mg O.6Mn, 6.2Zn 2.3Cu 2.2Mg 0.12Zr, Solution Heat Treated &
Solution Heat Treated, Cold Worked & Naturally Aged Overaged
SAE/AMS 4087F (Oct-90) Aluminum Alloy, Tubing, SAE/AMS 41 08E (May-96) Aluminum Alloy, Hand Forgings,
Seamless, Drawn, 4.4Cu 1.5Mg 0.60Mn Annealed 6.2Zn 2.3Cu 2.2Mg 0.12Zr Solution Heat Treated,
Compression Stress-Relieved, & Overaged
SAE/AMS 4088H (Oct-90) Aluminum Alloy, Tubing,
Seamless, Drawn, 4.4Cu 1.5Mg O.60Mn, Solution Heat SAE/AMS 4109A (Invalid D) Aluminum Alloy, Hand
Treated & Cold Worked Forgings, 5.6Zn 2.5Mg 1.6Cu 0.24Cr*
SAE/AMS 4089B (Jul-87) Aluminum Alloy, Plate, 5.7Zn SAE/AMS 4110D (Invalid D) Aluminum Alloy, Bars & Rods,
2.2Mg 1.6Cu 0.22Cr(7475-T7651) Solution Heat Rolled or Cold Finished 4.0Cu 0.70Mn 0.50Mg Stress
Treated, Stress Relieved by Stretching & Precipitation Relief Stretched*
Heat Treated SAE/AMS 4111 B (Jul-84) Aluminum Alloy, Forgings 7.7Zn
SAE/AMS 4090C (Sep-96) Aluminum Alloy, Plate 5.7Zn 2.5Mg 1.5Cu 0.16Cr, Solution & Precipitation Heat
2.2Mg 1.6Cu 0.22Cr Solution Heat Treated, Stress Treated
Relieved, & Precipitation Heat Treated SAE/AMS 4112D (Jul-77) Aluminum Alloy, Bars, Rods, &
SAE/AMS 4091A (Invalid D) Aluminum Alloy, Tubing Wire 4.4Cu 1.5Mg 0.60Mn Rolled, Drawn, or Cold
Hydraulic (6062 T4)* Finished
SAE/AMS 4093A (Invalid D) Aluminum Alloy, Tubing, SAE/AMS 4113C (Jan-94) Aluminum Alloy, Extruded
Hydraulic (6062 T6)* Shapes, 1.0Mg 0.60Si 0.28Cu 0.20Cr, Solution &
Precipitation Heat Treated
SAE/AMS 4094B (Sep-97) Aluminum Alloy, Sheet & Plate,
Alclad 6.3Cu 0.30Mn 0.18Zr 0.10V 0.06Ti Alclad 2219- SAE/AMS 4114G (Oct-90) Aluminum Alloy, Rolled or Cold-
T81 Sheet Solution Heat Treated, Cold Worked, & Finished, Bars & Rods, 2.5Mg 0.25Cr, As Fabricated
Precipitation Heat Treated Alclad 2219-T851 Plate SAE/AMS 4115F (Sep-96) Aluminum Alloy, Rolled or Cold-
Solution Heat Treated, Stress Relieved & Precipitation Finished, Bars, Rods, Wire, & Flash Welded Rings,
Heat Treated 1.0Mg 0.60Si 0.28Cu 0.20Cr, (6061-0) Annealed
SAE/AMS 4116F (Sep-96) Aluminum Alloy, Bars, Rods, &
Wire, 1.0Mg 0.60Si 0.30Cu 0.20Cr Cold Finished,
Solution Heat Treated
362 Appendix A - Standards
SAE/AMS (Aluminium) - continued. SAE/AMS 4137 A (Jul-81) Aluminum Alloy, Forgings 7.5Zn
SAE/AMS 4117G (Jul-94) Aluminum Alloy, Rolled or Cold 1.6Mg a.7Cu 0.55Mn (76S - T6)*
Finished Bars, Rods, & Wire & Flash Welded Rings, SAE/AMS 4138A (May-72) Aluminum Alloy, Forgings, 4.3Zn
1.0Mg O.60Si O.28Cu O.20Cr, Solution & Precipitation 3.3Mg O.6Cu O.2Mn O.2Cr
Heat Treated SAE/AMS 4139H (May-72) Aluminum Alloy, Forgings, 5.6Zn
SAE/AMS 4118J (Jan-94) Aluminum Alloy, Rolled or Cold 2.5Mg 1.6Cu 0.25Cr*
Finished Bars, Rods, & Wire, 4.0Cu O.70Mn O.60Mg SAE/AMS 4140G (Oct-91) Aluminum Alloy, Die Forgings
O.50Si, Solution Heat Treated 4.0Cu 2.0Ni O.68Mg Solution & Precipitation Heat
SAE/AMS 4119F (Invalid D) Aluminum Alloy, Bars, Rolled Treated
Drawn, or Cold Finished 4.4Cu 1.5Mg O.60Mn Stress- SAE/AMS 41410 (Jul-90) Aluminum Alloy, Die Forgings,
Relief Stretched* 5.6Zn 2.5Mg 1.6Cu O.23Cr Solution & Precipitation
SAE/AMS 4120P (Apr-95) Aluminum Alloy, Rolled or Cold Heat Treated
Finished Bars, Rods, & Wire, 4.4Cu 1.5Mg O.60Mn, SAE/AMS 4142C (Invalid D) Aluminum Alloy, Forgings 4Cu
Solution Heat Treated & Naturally Aged, Solution Heat 2Ni 1.5Mg 0.7Si As Fabricated*
Treated, Cold Worked, & Naturally Aged
SAE/AMS 4143C (Jul-91) Aluminum Alloy, Forgings &
SAE/AMS 4121 F (Jan-90) Aluminum Alloy, Bars, Rods, & Rolled or Forged Rings 6.3Cu 0.3Mn O.18Zr 0 10V
Wire Rolled or Cold Finished, 4.5Cu O.85Si O.80Mn O.06Ti, Solution & Precipitation Heat Treated
O.50Mg, Solution & Precipitation Heat Treated
SAE/AMS 4144E (Jul-95) Aluminum Alloy, Hand Forgings &
SAE/AMS 4122H (Oct-89) Aluminum Alloy, Bars, Rods, & Rings 6.3Cu 0.30Mn O.18Zr 0.1 OV O.06Ti Solution Heat
Wire Rolled or Cold Finished, & Rings, 5.6Zn 2.5Mg Treated, Mechanically Stress Relief, & Precipitation
1.6Cu O.23Cr, Solution & Precipitation Heat Treated Heat Treated
SAE/AMS 4123F (Oct-93) Aluminum Alloy, Rolled or Cold SAE/AMS 4145F (Feb-52) Alumunim Alloy, Forgings, 12.2Si
Finished Bars & Rods 5.6Zn 2.5Mg 1.6Cu O.23Cr 1.1 Mg O.9Cu O.9Ni*
(7075-T651) Solution & Precipitation Heat Treated
SAE/AMS 41460 (Oct-91) Aluminum Alloy, Forgings &
SAE/AMS 4124C (Apr-97) Aluminum Alloy, Rolled or Cold Rolled or Forged Rings 1.0Mg O.60Si 0.28Cu O.20Cr
Finished Bars, Rods, & Wire 5.6Zn 2.5Mg 1.6Cu Solution Heat Treated & Naturally Aged
O.23Cr Solution Heat Treated, Stress Relieved by
SAE/AMS 4147C (Jul-92) Aluminum Alloy, Forgings 5.6Zn
Stretching, & Overaged
2.5Mg 1.6Cu O.23Cr Solution Heat Treated, Stress
SAE/AMS 4125H (Apr-91) Aluminum Alloy, Die Forgings, & Relieved by Compression, & Overaged
Rolled or Forged Rings O.90Si 0.62Mg 0.25Cr Solution
SAE/AMS 4148C (Jan-93) Aluminum Alloy, Die Forgings
& Precipitation Heat Treated
5.6Zn 2.5Mg 1.6Cu 0.23Cr Solution & Precipitation
SAE/AMS 4126B (Sep-96) Aluminum Alloy, Die & Hand Heat Treated
Forgings & Rolled Rings 5.6Zn 2.5Mg 1.6Cu 0.23Cr
SAE/AMS 4149B (Oct-87) Aluminum Alloy, Forgings, 5.6Zn
(7079-T6) Solution & Precipitation Heat Treated
2.5Mg 1.6Cu O.23Cr [7175-T74 (formerly T736)]
SAE/AMS 4127G (Jul-91) Aluminum Alloy, Forgings & Solution & Precipitation Heat Treated
Rolled or Forged Rings, 1.0Mg 0.60Si 0.28Cu 0.20Cr
SAE/AMS 4150K (Sep-97) Aluminum Alloy, Extrusions &
Solution & Precipitation Heat Treated
Rings 1.0Mg 0.60Si O.28Cu O.20Cr Solution &
SAE/AMS 4128B (Oct-86) Aluminum Alloy, Bars, Rolled or Precipitation Heat Treated
Cold Finished 1.0Mg 0.60Si 0.30Cu 0.20Cr (6061-
SAE/AMS 4151A (Nov-44) Aluminum Alloy, Copper
T451) Solution Heat Treated & Stress Relieved by
Manganese Magnesium (17S-T) Extruded*
Stretching
SAE/AMS 4152L (Apr-93) Aluminum Alloy, Extrusions
SAE/AMS 4129B (Invalid D) Aluminum Alloy, Bars, Rolled
4.4Cu 1.5Mg 0.60Mn Solution Heat Treated
or Cold Finished 1.0Mg 0.60Si 0.28Cu 0.20Cr Stress
Relief Stretched* SAE/AMS 4153H (Apr-90) Aluminum Alloy, Extrusions,
4.5Cu 0.85Si O.80Mn 0.50Mg, Solution & PreCipitation
SAE/AMS 4130K (Apr-91) Aluminum Alloy, Die Forgings
Heat Treated
4.4Cu 0.85Si 0.80Mn Solution & Precipitation Heat
Treated SAE/AMS 4154L (Jul-90) Aluminum Alloy, Extrusions, 5.6Zn
25Mg 1.6Cu O.23Cr Solution & Precipitation Heat
SAE/AMS 4131C (Nov-96) Aluminum Alloy, Die & Hand
Treated
Forgings 5.6Zn 2.5Mg 1.6Cu 0.23Cr, Solution &
Precipitation Heat Treated & Aged SAE/AMS 4155B (Invalid D) Aluminum Alloy, Extrusions*
SAE/AMS 41320 (Jan-90) Aluminum Alloy, Die & Hand, SAE/AMS 4156H (Jan-91) Extrusions, Aluminum Alloy,
Forgings, Rolled Rings, & Forging Stock, 2.3Cu 1.6Mg O.68Mg 0.40Si Solution & PreCipitation Heat Treated
1.1 Fe 1.0Ni 0.18Si O.07Ti, Solution & Precipitation SAE/AMS 4157C (May-94) Aluminum Alloy, Extrusions,
Heat Treated 7.7Zn 2.4Mg 1.6Cu 0 16Cr (7049-T73511), Solution
SAE/AMS 4133C (Jul-90) Aluminum Alloy, Forgings & Heat Treated, Stress Relieved, & Overaged
Rolled Rings, 4.4Cu 0.85Si 0.80Mn 0.50Mg Solution & SAE/AMS 4158A (Jul-81) Aluminum Alloy, Extrusions 6.8
Precipitation Heat Treated Zn - 2.75 Mg - 2.0 Cu - 0.3 Cr (7178-T6)*
SAE/AMS 41340 (Jan-97) Aluminum Alloy, Die Forgings SAE/AMS 4159B (Apr-89) Aluminum Alloy, Extrusions,
4.4Cu 0.85Si 0.80Mn 0.50Mg, Solution Heat Treated 7.7Zn 2.4Mg 1.6Cu 0.16Cr, Solution Heat Treated,
SAE/AMS 4135M (Invalid D) Aluminum Alloy, Forgings Stress Relieved & Overaged
4.5Cu 0.85Si 0.8Mn 0.5Mg* SAE/AMS 4160F (May-96) Aluminum Alloy, Extrusions
SAE/AMS 4136A (Jun-62) Aluminum Alloy, Forgings, 4.3Zn 1.0Mg 0.60Si O.28Cu 0.20Cr Annealed
3.3Mg 0.6Cu O.2Mn 0.2Cr, Solution & Precipitation
Heat Treated, Low Residual Stresses*
Appendix A - Standards 363
SAE/AMS (Aluminium) - continued. SAE/AMS 4184D (Oct-90) Filler Metal, Aluminum Brazing,
SAE/AMS 4161F (May-96) Aluminum Alloy, Extrusions 10Si 4.0Cu
1.0Mg 0.60Si 0.28Cu 0.20Cr, Solution Heat Treated & SAE/AMS 418SC (Oct-90) Filler Metal, Aluminum Brazing,
Naturally Aged 12Si
SAE/AMS 4162B (Apr-90) Aluminum Alloy, Extrusions, SAE/AMS 4186B (Apr-89) Aluminum Alloy, Bars, Rods, &
6.3Cu 0.30Mn 0.18ZrO.10VO.06Ti, (2219-T8511) Wire, Rolled or Cold Finished, 5.6Zn 2.5Mg 1.6Cu
Solution Treated, Stress Relief Stretched, Precipitation 0.23Cr, As Fabricated
Heat Treated SAE/AMS 4187B (Jan-83) Bars & Rods, Rolled, Drawn, or
SAE/AMS 4163B (Apr-90) Aluminum Alloy, Extrusions, Cold Finished 5.6Zn 2.5Mg 1.6Cu 0.26Cr, Annealed
6.3Cu 0.30Mn 0.18Zr 0.1 OV 0.06Ti Solution Heat SAE/AMS 4188/1 (Invalid D) Aluminum Alloy, Welding Wire
Treated & Stress-Relieved by Stretching 4.5Cu 0.70Ag 0.30Mn 0.2SMg 0.2STi*
SAE/AMS 4164F (Apr-90) Aluminum Alloy, Extrusions, SAE/AMS 4188/2 (Invalid D) Aluminum Alloy, Welding Wire
4.4Cu 1.5Mg 0.60Mn, Stress-Relief Stretched, 4.6Cu 0.3SMn 0.2SMg 0.22Ti*
Unstraightened
SAE/AMS 4188/3 (Invalid D) Aluminum Alloy, Welding Wire
SAE/AMS 416SF (Apr-92) Aluminum Alloy, Extrusions S.OSi 1.2Cu O.SOMg*
4.4Cu 1.5Mg 0.60Mn, Stress-Relieved Stretched &
SAE/AMS 4188/4 (Invalid D) Aluminum Alloy, Welding Wire
Straightened
7.0Si 0.30Mg*
SAE/AMS 4166D (Jan-91) Extrusions, Aluminum Alloy,
SAE/AMS 4188/S (Invalid D) Aluminum Alloy, Welding Wire
5.6Zn 2.SMg 1.6Cu 0.23Cr Solution Heat Treated &
7.0Si 0.S2Mg*
Overaged
SAE/AMS 4188A (Invalid D) Aluminum Alloy, Welding Wire*
SAE/AMS 4167G (Jul-9S) Aluminum Alloy, Extrusions,
S.6Zn 2.SMg 1.6Cu 0.23Cr Solution Heat Treated, SAE/AMS 4189E (Jul-96) Aluminum Alloy, Welding Wire
Stress Relieved by Stretching, & Overaged 4.1Si 0.2Mg
SAE/AMS 4168G (Apr-92) Aluminum Alloy, Extrusions SAE/AMS 4190F (Jul-96) Aluminum Alloy, Welding Wire
S.6Zn 2.SMg 1.6Cu 0.23Cr Solution Heat Treated, S.2Si
Stress Relieved by Stretching, & Precipitation Heat SAE/AMS 4191F (Jul-96) Aluminum Alloy, Welding Wire,
Treated Unstraightened 6.3Cu 0.3Mn 0.18Zr 0.1STi 0.10V
SAE/AMS 4169H (Apr-92) Aluminum Alloy, Extrusions SAE/AMS 4192A (Invalid D) Aluminum Alloy, Sheet & Plate
5.6Zn 2.SMg 1.6Cu 0.23Cr Solution Heat Treated, 4.4Cu 1.SMg 0.60Mn (2024-T361)*
Stress Relieved by Stretching, & Precipitation Heat
SAE/AMS 4193B (Apr-89) Aluminum Alloy, Sheet & Plate,
Treated Straightened
4.4Cu 1.5Mg 0.60Mn, Solution Heat Treated, Cold
SAE/AMS 4170 (Jul-81) Aluminum Alloy, Impact Extrusions Worked, & Precipitation Heat Treated
5.6Zn 2.5Mg 1.6Cu 0.2SCr (7SS-T6)*
SAE/AMS 4194B (Apr-89) Aluminum Alloy, Sheet & Plate,
SAE/AMS 4171 C (Apr-78) Aluminum Alloy Extrusions, Alclad, 4.4Cu 1.5Mg 0.60Mn, Solution Heat Treated &
4.3Zn 3.3Mg 0.60Cu 0.20Mn 0.18Cr* Cold Worked
SAE/AMS 4172D (May-96) Aluminum Alloy, Extrusions SAE/AMS 419SB (Jan-89) Aluminum Alloy, Sheet & Plate,
1.0Mg 0.60Si 0.28Cu 0.20Cr Solution Heat Treated & Alclad, 4.4Cu 1.SMg 0.60Mn, Solution Heat Treated,
Stress Relieved by Stretching Cold Worked, & Precipitation Heat Treated
SAE/AMS 4173C (Jul-91) Aluminum Alloy, Extrusions SAE/AMS 4196A (Invalid D) Aluminum Alloy, Sheet & Plate,
1.0Mg 0.60Si 0.30Cu 0.20Cr Solution Heat Treated, Alclad, S.6Zn 2.SMg 1.6Cu 0.26Cr*
Stress Relieved by Stretching, & Precipitation Heat
SAE/AMS 4197A (Invalid D) Aluminum alloy Sheet & Plate,
Treated
Alclad 5.6Zn 2.SMg 1.6Cu 0.26Cr*
SAE/AMS 4174C (Dec-94) Aluminum Alloy, Flash Welded
SAE/AMS 4198A (Invalid D) Aluminum Alloy, Sheet Plate
Rings, 5.6Zn 2.5Mg 1.6Cu 0.23Cr, Solution &
Alclad 4.3Zn-3.3Mg-0.6Cu-0.20Mn-0.17C (7011 Alclad
Precipitation Heat Treated
7079-0)*
SAE/AMS 4175B (Jan-77) Honeycomb Core, Aluminum
SAE/AMS 4199A (Invalid D) Aluminum Alloy, Sheet & Plate,
Alloy, For Sandwich Construction, S052, 3S0 (175)
Alclad 4.3Zn 3.3Mg 0.6Cu 0.20Mn 0.17Cr*
SAE/AMS 4176B (Jan-77) Honeycomb Core, Aluminum
SAE/AMS 4200A (Oct-91) Aluminum Alloy, Plate 7.7Zn
Alloy, For Sandwich Construction, 5056, 350 (175)
2.4Mg 1.6Cu 0.16Cr Solution HeatTreated, Stress
SAE/AMS 4177C (Apr-9S) Core, Flexible Honeycomb, Relieved, & Precipitation Heat Treated
Aluminum Alloy, for Sandwich Construction, 50S6, 350
SAE/AMS 4201 B (Jul-92) Aluminum Alloy, Plate 6.2Zn
(177)
2.3Cr 2.2Mg 0.12Zr Solution Heat Treated, Stress
SAE/AMS 4178C (Nov-9S) Core, Flexible Honeycomb, Relieved, & Overaged
Aluminum Alloy, Treated, For Sandwich Construction,
SAE/AMS 4202C (Jul-89) Aluminum Alloy, Plate, 5.7Zn
5052, 350 (177)
2.2Mg 1.6Cu 0.22Cr, Solution Heat Treated, Stress
SAE/AMS 4179B (Jan-87) Aluminum Alloy, Forgings 5.6Zn Relieved by Stretching, & Precipitation Heat Treated
2.5Mg 1.6Cu 0.23Cr (717S-T7452) Solution Heat
SAE/AMS 4203B (Nov-96) Aluminum Alloy, Plate, 6.2Zn
Treated, Stress Relieved, & Precipitation Heat Treated
1.8Cu 2.4Mg 0.13Zr, Solution Heat Treated, Stress
SAE/AMS 4180E (Oct-93) Aluminum Wire, 99.0AI Minimum Relieved & Precipitation Heat Treated
(1100-H18)
SAE/AMS 4204B (Nov-9S) Aluminum Alloy, Plate 6.2Zn
SAE/AMS 4181 B (Jul-96) Aluminum Alloy, Welding Wire 1.8Cu 2.4Mg 0.13Zr, Solution Heat Treated, Stress
7.0Si 0.38Mg 0.10Ti Relieved, & Precipitation Heat Treated
SAE/AMS 4182E (Oct-93) Aluminum Alloy, Wire S.OMg
0.12Mn 0.12Cr (S056-0), Annealed
364 Appendix A - Standards
SAE/AMS (Aluminium) - continued. SAE/AMS 4232 (Jan-90) Aluminum Alloy, Extrusion, 2.7Cu
SAE/AMS 42058 (Nov-95) Aluminum Alloy, Plate 6.2Zn 2.2Li 0.12Zr, Solution Heat Treated, Cold Worked, &
1.BCu 2.4Mg 0.13Zr, Solution Heat Treated, Stress Precipitation Heat Treated
Relieved, & Precipitation Heat Treated SAE/AMS 42338 (Jul-96) Aluminum Alloy, Welding Wire
SAE/AMS 4207A (Apr-B9) Aluminum Alloy, Sheet, Alclad, 4.5Cu 0.70Ag 0.30Mn 0.25Mg 0.25Ti
5.7Zn 2.2Mg 1.6Cu 0.22Cr, Solution & Precipitation SAE/AMS 4234A (May-45) Aluminum Alloy, Castings Sand
Heat Treated Secondary 4 Copper Solution & Precipitation*
SAE/AMS 420BA (Apr-90) Aluminum Alloy, Sheet, 6.0Cu SAE/AMS 4235A (Jan-B7) Aluminum Alloy, Castings 4.6Cu
0.40Zr, As Rolled 0.35Mn 0.25Mg 0.22Ti (A206.0-T71) Solution &
SAE/AMS 4209A (Oct-90) Aluminum Alloy, Sheet, Alclad, Precipitation Heat Treated
6.0Cu 0.40Zr, As Rolled SAE/AMS 4236A (Jan-B7) Aluminum Alloy, Castings 4.6Cu
SAE/AMS 4210J (Mar-96) Aluminum Alloy, Castings 5.0Si 0.35Mn 0.25Mg 0.22Ti (A206.0-T4) Solution Heat
1.2Cu 0.50Mg Precipitation Heat Treated Treated & Naturally Aged
SAE/AMS 4212H (Mar-96) Aluminum Alloy, Castings 5.0Si SAE/AMS 4237A (Oct-B7) Aluminum Alloy, Castings, Sand,
1.2Cu 0.50Mg, Solution & Precipitation Heat Treated 4.6Cu 0.35Mn 0.25Mg 0.22Ti (206.0-T71), Solution
Heat Treated & Naturally Aged
SAE/AMS 4214G (Jan-91) Castings, Aluminum Alloy, Sand
5.0Si 1.2Cu 0.50Mg Solution Heat Treated & Stabilized SAE/AMS 423BO (Jul-91) Aluminum Alloy Castings, Sand
6.BMg 0.18Ti 0.1BMn, As Cast
SAE/AMS 4215F (Oec-94) Aluminum Alloy, Castings 5.0Si
1.2Cu 0.50Mg, Solution & Precipitation Heat Treated SAE/AMS 4239C (Jul-91) Aluminum Alloy Castings, Sand
6.BMg 0.1BTi 0.1BMn, Annealed
SAE/AMS 4216 (Jul-B9) Aluminum Alloy, Sheet, 1.0Mg
O.BSi O.BCu 0.50Mn, Solution Heat Treated & SAE/AMS 4240F (Jul-B2) Castings, Sand, 1OMg, Solution
Artificially Aged Heat Treated & Naturally Aged
SAE/AMS 4217G (Jun-96) Aluminum Alloy, Castings 7Si SAE/AMS 4241A (Jul-92) Aluminum Alloy, Castings 7.0Si
0.3Mg, Solution & Precipitation Heat Treated 0.5BMg 0.15Ti 0.068e (0357.0-T6) Solution &
Precipitation Heat Treated Dendrite Arm Spacing
SAE/AMS 421BG (Jan-94) Aluminum Alloy, Castings, 7.0Si
(OAS) Controlled
0.35Mg, Solution & Precipitation Heat Treated
SAE/AMS 4242A (Sep-97) Aluminum Alloy, Castings, 4.7Cu
SAE/AMS 4219C (Jul-92) Aluminum Alloy, Castings 7.0Si 0.60Ag 0.35Mn 0.25Mg 0.25Ti (82010-T7) Solution
0.55Mg, 0.12Ti 0.068e, Solution & Precipitation Heat Heat Treated & Overaged Aircraft
Treated
SAE/AMS 4243A (Nov-96) Aluminum Alloy, Alclad Sheet
SAE/AMS 4220E (Jun-69) Aluminum Alloy, Castings, Sand, 6.2Zn 2.3Cu 2.2Mg 0.12Zr, Solution Heat Treated &
4Cu 2Ni 1.5Mg O.2Cr, Solution Treated & Overaged* Overaged
SAE/AMS 4221A (Sep-95) Aluminum Alloy, Plate 4.4Cu SAE/AMS 4244 (Jan-B7) Aluminum Alloy, Welding Wire
1.5Mg 0.60Mn (2124-TB151) Solution Heat Treated, 4.6Cu 0.35Mn 0.25Mg 0.22Ti for Welding 206 Type
Stress Relieved, & Precipitation Heat Treated Alloys
SAE/AMS 4222G (Apr-B4) Castings, Sand, Moderate Heat SAE/AMS 42458 (Jul-96) Aluminum Alloy, Welding Wire
Resistance, 4Cu 2Ni 1.5Mg 0.12Ti, Solution Heat 5.0Si 1.2Cu 0.50Mg
Treated & Stabilized
SAE/AMS 42468 (Jul-96) Aluminum Alloy, Welding Wire
SAE/AMS 4223C (Mar-96) Aluminum Alloy, Castings 4.5Cu 7.0Si 0.52Mg
0.70Ag 0.30Mn 0.25Mg 0.25Ti, Solution Heat Treated
& Naturally Aged SAE/AMS 4247A (May-94) Aluminum Alloy, Hand Forgings
7.7Zn 2.4Mg 1.6Cu 0.16Cr (7049-T7352) Solution Heat
SAE/AMS 42248 (Oct-B7) Aluminum Alloy, Castings, Sand, Treated, Stress Relieved by Compression, &
4.0Cu 2.1Ni 2.0Mg 0.30Cr 0.30Mn 0.13Ti 0.13V Precipitation Heat Treated
(243.0), Stabilized
SAE/AMS 424BA (Apr-93) Aluminum Alloy, Hand Forgings
SAE/AMS 4225C (Jul-96) Aluminum Alloy, Heat Resistant, & Rolled Rings 1.0Mg 0.60Si 0.28Cu 0.20Cr Solution
Castings 50Cu 1.5Ni 0.25Mn 0.25Sb 0.25Co 0.20Ti Heat Treated, Stress Relief by Compression, &
0.20Zr, Solution Heat Treated & Stabilized Precipitation Heat Treated
SAE/AMS 4226A (Nov-6B) Castings, High Strength, 5.0Cu SAE/AMS 4249 (Jul-92) Aluminum Alloy, Castings 7.0Si
0.35Mn 0.1BZr 0.1 OV, Solution & Precipitation Heat 0.58Mg 0.15Ti 0.068e Solution & Precipitation Heat
Treated Treated (Requiring Fatigue & Fracture Toughness
SAE/AMS 42270 (Apr-BB) Aluminum Alloy, Castings, Sand, Testing)
B.OCu 6.0Mg 0.50Mn 0.50Ni, As Cast SAE/AMS 4251 (Apr-B9) Aluminum Alloy, Sheet, 2.7Cu
SAE/AMS 422B8 (Jan-76) Aluminum Alloy, Castings, High 2.2Li 0.12Zr, Solution Heat Treated, Cold Worked, &
Strength, 4.5Cu 0.70Ag 0.30Mn 0.25Mg 0.25Ti, Precipitation Heat Treated
Solution & Precipitation Heat Treated* SAE/AMS 4252A (Mar-95) Aluminum Alloy, Plate 6.4Zn
SAE/AMS 4229C (Jan-90) Aluminum Alloy, Castings, High 2.4Mg 2.2Cu 0.12Zr, Solution Heat Treated, Stress
Strength, 4.5Cu 0.70Ag 0.30Mn 0.25Mg 0.25Ti, Relieved, & Overaged
Solution Heat Treated & Overaged SAE/AMS 4253 (Jul-B9) Aluminum Alloy, Aramid Fiber
SAE/AMS 42300 (Aug-5B) Aluminum Alloy, Castings, Sand, Reinforced-Laminated Sheet, 5.7Zn 2.2Mg 1.6Cu
4.5Cu, Solution Treated* 0.22Cr, 3, 5, 7, or 9 Ply
SAE/AMS 4231 F (Jul-B3) Castings, Sand, 4.5Cu 1.1 Si, SAE/AMS 4254A (Jan-93) Aluminum Alloy, Aramid Fiber
Solution & Precipitation Heat Treated Reinforced, Laminated Sheet 4.4Cu 1.5Mg 0.6Mn, 3, 5,
7, or 9 Ply
Appendix A - Standards 365
SAE/AMS (Aluminium) - continued. SAE/AMS 4291 F (Mar-96) Aluminum Alloy, Die Castings
SAE/AMS 4255A (Sep-95) Aluminum Alloy, Clad One Side 8.5Si - 3.5Cu As Cast
Sheet 0.6Mg 0.35Si 0.28Cu (No. 21 Brazing Sheet) As SAE/AMS 4292 (Jun-56) Cast Aluminum Alloy, Pressure
Fabricated Molded (Aluminum Silicon)-
SAE/AMS 4256A (Sep-95) Aluminum Alloy, Clad Two Sides SAE/AMS 4296 (Sep-97) Aluminum Alloy, Alciad Sheet &
Sheet 0.6Mg 0.35Si 0.28Cu (No. 22 Brazing Sheet) As Plate 4.3Cu 1.4Mg 0.60Mn Solution Heat Treated &
Fabricated Cold Worked
SAE/AMS 4258 (Jan-92) Laminated Sheet Aluminum Alloy, SAE/AMS 4300B (Jul-90) Boron-Aluminum Composite
Aramid Fiber Reinforced 5.7Zn 2.2Mg 1.6Cu 0.22Cr. Sheet, 50 V/O 5.6B, 6061-0, For Diffusion Bonding
(Alciad, One Side 7475-T761) 5 or 7 Ply SAE/AMS 4301 C (Apr-85) Boron-Aluminum Composite
SAE/AMS 4259 (Apr-94) Aluminum Alloy, Sheet 2.4Li 1.3Cu Sheet - 50 V/O 5.6B, 2024-0, For Diffusion Bonding-
0.95Mg 0.1 OZr Solution & Precipitation Heat Treated SAE/AMS 4302A (Jan-92) Aluminum Alloy, Laminated,
(Unrecrystallized) Sheet, Aramid Fiber Reinforced, 5.7Zn 2.2Mg 1.6Cu
SAE/AMS 4260E (Jul-94) Aluminum Alloy, Investment 0.22Cr, 3, 5, or 7 Ply
Castings, 7.0Si 0.32Mg, Solution & Precipitation Heat SAE/AMS 4303 (Jan-90) Aluminum Alloy, Plate, 2.7Cu 2.2Li
Treated 0.12Zr, Solution HeatTreated, Cold Worked, & Aged
SAE/AMS 42610 (Jul-91) Aluminum Alloy, Castings, SAE/AMS 4304 (Jan-93) Aluminum Alloy, Discontinuously
Investment 7.0Si 0.30Mg, Precipitation Heat Treated Reinforced Sheet 2009/SiC/15W (T8P) Solution Heat
SAE/AMS 4263A (Jul-89) Aluminum Silicon Bronze Bars, Treated, Stretched, & Precipitation Heat Treated
Rods, & Forgings, 90Cu 7.0AI 1.9Si, Drawn & Stress SAE/AMS 4306A (Oct-93) Aluminum Alloy, Plate 6.4Zn
Relieved* 2.4Mg 2.2Cu 0.12Zr, Solution Heat Treated, Stress
SAE/AMS 4264A (Apr-92) Bronze, Aluminum Silicon, Rods, Relieved, & Aged
Bars, & Forgings 90Cu 7.0AI 1.8Si Drawn & Stress SAE/AMS 4307 (Oct-88) Aluminum Alloy, Extrusions, 6.4Zn
Relieved (HR50) 2.4Mg 2.2Cu 0.12Zr, Solution Heat Treated, Stress
SAE/AMS 4265 (Nov-94) Aluminum Alloy, Particulate Relieved, & Precipitation Heat Treated
Reinforced Extrusions 6092/SiC/25p - T6P Solution SAE/AMS 4308 (Apr-94) Aluminum Alloy, Sheet, 8.6Fe
Heat Treated, Quenched, & Precipitation Heat Treated 1.8Si 1.3V Powder Metallurgy Product, Strain
SAE/AMS 4266 (Mar-94) Aluminum Alloy, Sheet 6.5Fe Hardened
1.3Si 0.60V (8002-H 112) Powder Metallurgy Product, SAE/AMS 4309 (Apr-94) Aluminum Alloy, Extrusions 8.6Fe
Strain Hardened 1.8Si 1.3V Powder Metallurgy Product, Strain-
SAE/AMS 4270A (Sep-97) Aluminum Alloy, Alclad Flat Hardened
Sheet 4.1 Cu 1.4Mg 0.45Mn Solution Heat Treated & SAE/AMS 4310C (Jun-94) Aluminum Alloy, Rolled or
Cold Worked Forged Rings, 5.6Zn 2.5Mg 1.6Cu 0.23Cr (7075-T651,
SAE/AMS 4273 (Jan-97) Aluminum Alloy, Sheet 4.1 Cu 7075-T652), Solution Heat Treated, Mechanically
1.4Mg 0.45Mn Solution Heat Treated & Cold Worked Stress Relieved, & Precipitation Heat Treated
SAE/AMS 42750 (Jan-77) Castings, Permanent Mold, SAE/AMS 4311 C (Jul-94) Aluminum Alloy, Rolled or Forged
6.2Sn 1Cu 1Ni, Stress Relieved Rings, 5.6Zn 2.5Mg 1.6Cu 0.23Cr Solution Heat
SAE/AMS 4276 (Sep-97) Aluminum Alloy, Sheet 4.4Cu Treated, Mechanically Stress Relieved, & Precipitation
1.5Mg 0.60Mn Annealed, Fine Grained Heat Treated
SAE/AMS 4280G (Apr-90) Aluminum Alloy, Castings, SAE/AMS 4312B (Mar-94) Aluminum Alloy Rings, Rolled or
Permanent Mold, 5.0Si 1.2Cu 0.5Mg, Solution Heat Forged Rings, 1.0Mg 0.60Si O.28Cu 0.20Cr Solution
Treated & Overaged Heat Treated, Mechanically Stress Relieved, &
Precipitation Heat Treated
SAE/AMS 4281 E (Oct-89) Aluminum Alloy, Castings,
Permanent Mold, 5Si 1.2Cu 0.5Mg, Solution & SAE/AMS 4313B (May-94) Aluminum Alloy, Rolled or
Precipitation Heat Treated Forged Rings, 6.3Cu 0.30Mn 0.18Zr 0.1 OV 0.06Ti,
Solution Heat Treated & Mechanically Stress Relieved
SAE/AMS 4282E (Oct-81) Aluminum Alloy, Castings,
Permanent Mold 4.5Cu 2.5Si Solution & Precipitation SAE/AMS 4314B (Jan-87) Aluminum Alloy, Rings, Rolled or
Heat Treated6* Forged 4.5Cu 0.85Si 0.80Mn 0.50Mg Solution Heat
Treated, Mechanically Stress Relieved & Precipitation
SAE/AMS 42830 (Jul-81) Aluminum Alloy, Casting,
Heat Treated
Permanent Mold 4.5 Cu, 2.5 Si (81 95-T4) Solution
Treated* SAE/AMS 4318 (Jun-94) Aluminum Alloy, Rolled or Cold
Finished Bars & Rods 12,2Si 1.0Mg 0.90Cu 0.90Ni
SAE/AMS 4284F (Oct-89) Aluminum Alloy, Castings, (4032-T86) Solution Heat Treated, Cold Worked, &
Permanent Mold, 7Si 0.3Mg, Solution & Precipitation
Artificially Aged
Heat Treated
SAE/AMS 4320A (Jul-90) Aluminum Alloy, Forgings, 7.7Zn
SAE/AMS 4285B (Jan-90) Aluminum Alloy, Castings, 2.5Mg 1.5Cu 0.16Cr, Solution & Precipitation Heat
Centrifugal, 7.0Si 0.3Mg, Solution & Precipitation Heat
Treated
Treated
SAE/AMS 4321A (Jan-93) Aluminum Alloy, Forgings 7.7Zn
SAE/AMS 42860 (Jul-84) Aluminum Alloy, Castings,
2.5Mg 1.5Cu 0.16Cr High Temperature Annealed
Permanent Mold 7Si 0.32Mg, Precipitation Heat
Treated SAE/AMS 4322 (Jul-92) Aluminum Alloy, Die Forgings
4.0Mg 1.3Li 1.2C 0.4502 Mechanically Alloyed, As-
SAE/AMS 4290J (Mar-96) Aluminum Alloy, Die Castings
Fabricated
9.5Si 0.50Mg, As Cast
366 Appendix A - Standards
SAE/AMS (Aluminium) - continued. ISO 793:1973: Aluminium & aluminium alloys-
SAE/AMS 4323A (Jan-97) Aluminum Alloy, Hand Forgings, Determination of iron - Orthophenanthroline
5.6Zn 2.5Mg 1.6Cu 0.23Cr, Solution Heat Treated, photometric method
Stress Relieved, & Precipitation Heat Treated ISO 795:1976 : Aluminium & aluminium alloys-
SAE/AMS 4333A (May-96) Aluminum Alloy, Die Forgings, Determination of copper content - Oxalyldihydrazide
6.2Zn 2.3Cu 2.2Mg 0.12Zr Solution Heat Treated, photometric method
Compression Stress-Relieved, & Overaged ISO 796:1973 : Aluminium alloys - Determination of copper-
SAE/AMS 4334 (Jul-95) Aluminum Alloy, Forgings 7.8Zn Electrolytic method
2.2Mg 1.6Cu 0.15Cr ISO 7971973 : Aluminium & aluminium alloys-
SAE/AMS 4339 (Mar-94) Aluminum Alloy, Rolled or Cold Determination of silicon - Gravimetric method
Finished Bars & Rods 4.4Cu 1.5Mg 0.60Mn Solution ISO 8081973 : Aluminium & aluminium alloys -
Heat Treated, Cold Worked, & Artificially Aged Determination of silicon - Spectrophotometric method
SAE/AMS 4340C (Apr-89) Aluminum Alloy, Extrusions, with the reduced silicomolybdic complex
6.2Zn 2.3Cu 2.2Mg 0.12Zr, Solution Heat Treated, ISO 886:1973 : Aluminium & aluminium alloys-
Stress Relieved, & Overaged Determination of manganese - Photometric method
SAE/AMS 4341C (Oct-91) Aluminum Alloy, Extrusions (Manganese content between 0.005 & 1.5 %)
6.2Zn 2.3Cu 2.2Mg 0.12Zr Solution Heat Treated, ISO 1118: 1978 : Aluminium & aluminium alloys -
Stress Relieved & Overaged Determination of titanium - Spectrophotometric
SAE/AMS 4342B (Oct-91) Aluminum Alloy, Extrusions chromotropic acid method
6.2Zn 2.3Cu 2.2Mg 0.12Zr Solution Heat Treated, ISO 1784: 1976 : Aluminium alloys - Determination of zinc -
Stress Relieved, & Overaged EDTA titrimetric method
SAE/AMS 4343C (May-96) Aluminum Alloy, Extrusions, ISO 1965:1973 : Aluminium terminal ends for crimping to
7.7Zn 2.4Mg 1.6Cu 0.16Cr, Solution Heat Treated, aircraft aluminium electrical cables
Stress Relieved by Stretching, & Overaged ISO 2063, Publication:1991-11 : Metallic & other inorganic
SAE/AMS 4344A (Jul-90) Aluminum Alloy, Extrusions, coatings; thermal spraying; zinc, aluminium & their
5.6Zn 2.5Mg 1.6Cu 0.23Cr Solution Heat Treated, alloys.
Stress Relieved, & Overaged ISO 2085:1976: Anodizing of aluminium & its alloys - Check
SAE/AMS 4345 (Oct-89) Aluminum Alloy, Extrusions, 6.4Zn of continuity of thin anodic oxide coatings - Copper
2.4Mg 2.2Cu 0.12Zr, Solution Heat Treated, Stress sulphate test
Relieved, & Overaged ISO 2107:1983: Aluminium, magnesium & their alloys-
SAE/AMS 4346A (Invalid D) Aluminum Alloy, Plate, 2.7Cu- Temper designations
2.2Li-0.12Zr (2090-T81) Solution Heat Treated, Cold ISO 2128:1976: Anodizing of aluminium & its alloys-
Worked, & Precipitation Heat Treated Determination of thickness of anodic oxide coatings -
SAE/AMS 4347 A (Apr-92) Aluminum Alloy, Sheet, 1.0Mg Non-destructive measurement by split-beam
0.8Si 0.8Cu 0.50Mn Solution Heat Treated & Naturally microscope
Aged ISO 2135:1984: Anodizing of aluminium & its alloys -
SAE/AMS 4348C (Apr-95) Core, Honeycomb Aluminum Accelerated test of light fastness of coloured anodic
Alloy, Corrosion Inhibited, For Sandwich Construction, oxide coatings using artificial light
5052, 350 (177) ISO 2142:1981 : Wrought aluminium, magnesium & their
SAE/AMS 4349C (Apr-95) Core, Honeycomb, Aluminum alloys - Selection of specimens & test pieces for
Alloy, Corrosion Inhibited For Sandwich Construction mechanical testing
5056, 350 (177) ISO 2143:1981 : Anodizing of aluminium & its alloys-
Note: * denotes that a standard has been cancelled or Estimation of loss of absorptive power of anodic oxide
superseded as a result of technical committee action; coatings after sealing - Dye spot test with prior acid
photocopies are available from SAE. treatment
ISO 2297:1973: Chemical analysis of aluminium & its alloys
- Complexometric determination of magnesium
ISO Standards
ISO 2376:1972 : Anodization (anodic oxidation) of
ISO/R 115: 1968 : Classification & composition of unalloyed aluminium & its alloys - Insulation check by
aluminium ingots for remelting measurement of breakdown potential
ISO/DIS 115 : Unalloyed aluminium ingots for remelting - ISO 2378:1972: Aluminium alloy chill castings - Reference
Classification & composition (Revision of ISO/R test bar
115:1968) ISO 2379:1972 : Aluminium alloy sand castings - Reference
ISO 121:1980: Magnesium-aluminium-zinc alloy ingots & test bar
alloy castings - Chemical composition & mechanical
ISO 2931 :1983: Anodizing of aluminium & its alloys-
properties of sand cast reference test bars Assessment of quality of sealed anodic oxide coatings
ISO 209-1 :1989: Wrought aluminium & aluminium alloys- by measurement of admittance or impedance
Chemical composition & forms of products - Part 1:
ISO 3211 :1977: Anodizing of aluminium & its alloys-
Chemical composition Assessment of resistance of anodic oxide coatings to
ISO 209-2:1989: Wrought aluminium & aluminium alloys- cracking by deformation
Chemical composition & forms of products - Part 2:
ISO 3255:1974: Magnesium & magnesium alloys-
Forms of products
Determination of aluminium - Chromazurol S
ISO 791 :1973 : Magnesium alloys - Determination of photometric method
aluminium - 8-hydroxyquinoline gravimetric method
Appendix A - Standards 367
ISO (Aluminium) - continued. ISO 6362-5:1991 : Wrought aluminium & aluminium alloy
ISO 3256:1977: Aluminium & aluminium alloys- extruded rods/bars, tubes & profiles - Part 5: Extruded
Determination of magnesium - Atomic absorption round, square & hexagonal bars - Tolerances on form
spectrophotometric method & dimensions
ISO 3522:1984: Cast aluminium alloys - Chemical ISO/DIS 6362-8 : Wrought aluminium & aluminium alloys
composition & mechanical properties extruded rods/bars, tubes & profiles - Part 8: Extruded
tubes - Tolerances on form & dimensions (Item
ISOIOIS 3613 : Chromate conversion coatings on zinc,
confirmed in May 1993)
cadmium aluminium-zinc alloys & zinc-aluminium
alloys - Test methods (Revision of ISO 36131980) ISO 6363-1:1988: Wrought aluminium & aluminium alloy
cold-drawn rods/bars & tubes - Part 1: Technical
ISO 3978:1976: Aluminium & aluminium alloys - . conditions for inspection & delivery
Determination of chromium - Spectrophotometric
method using diphenylcarbazide, after extraction ISO 6363-2:1993: Wrought aluminium & aluminium alloy
cold-drawn rods/bars & tubes - Part 2: Mechanical
ISO 3979:1977 : Aluminium & aluminium alloys ~ properties
Determination of nickel - Spectrophotometric method
using dimethylglyoxime ISO 6363-4:1991 : Wrought aluminium & aluminium alloy
cold-drawn rods/bars & tubes - Part 4: Drawn
ISO 3980:1977 : Aluminium & aluminium alloys-
rectangular bars - Tolerances on form & dimensions
Determination of copper - Atomic absorption
spectrophotometric method ISO 6363-5:1992: Wrought aluminium & aluminium alloy
cold-drawn rods/bars & tubes - Part 5: Drawn square &
ISO 3981: 1977 : Aluminium & aluminium alloys - hexagonal bars - Tolerances on form & dimensions
Determination of nickel - Atomic absorption
spectrophotometric method ISO 6365-1:1988: Wrought aluminium & aluminium alloy
cold-drawn wire - Part 1: Technical conditions for
ISO 4192:1981 : Aluminium & aluminium alloys-
inspection & delivery
Determination of lead content - Flame atomic
absorption spectrometric method ISO 6581 :1980: Anodizing of aluminium & its alloys-
Determination of the fastness to ultra-violet light of
ISO 4193:1981 : Aluminium & aluminium alloys - .
coloured anodic oxide coatings
Determination of chromium content - Flame atomic
absorption spectrometric method ISO 6719:1986: Anodized aluminium & aluminium alloys-
Measurement of reflectance characteristics of
ISO 5193:1981 : Wrought aluminium & aluminium alloys-
aluminium surfaces using integrating-sphere
Drawn round bars - Tolerances on shape & dimensions
instruments
(Symmetric plus & minus tolerances on diameter)
ISO 6827:1981 : Aluminium & aluminium alloys-
ISO 5194:1981 : Aluminium & aluminium alloys-
Determination of titanium content - Diantipyrylmethane
Determination of zinc content - Flame atomic
photometric method
absorption spectrometric method
ISO 7061: 1993 : Shipbuilding - Aluminium shore gangways
ISO 5832-10:1996: Implants for surgery - Metallic materials
for seagoing vessels
- Part 10 Wrought titanium 5-aluminium 2, 5-iron alloy
ISO 7141: 1995 : Passenger cars - Light alloy wheels -
ISO 5832-11: 1994 : Implants for surgery - Metallic materials
Impact test
- Part 11: Wrought titanium 6-aluminium 7-niobium
alloy ISO 7271:1982: Aluminium & aluminium alloys - Foil & thin
strip - Dimensional tolerances
ISO 6279:1979: Plain bearings - Aluminium alloy for solid
bearings ISO 7274:1981 : Wrought aluminium & aluminium alloys-
Drawn round bars - Tolerances on shape & dimensions
ISO 6361-1:1986: Wrought aluminium & aluminium alloy
(All minus tolerances on diameter)
sheets, strips & plates - Part 1: Technical conditions for
inspection & delivery ISO 7583:1986 : Anodizing of aluminium & its alloys-
Vocabulary
ISO 6361-2:1990: Wrought aluminium & aluminium alloy
sheets, strips & plates - Part 2: Mechanical properties ISO 7599:1983: Anodizing of aluminium & its alloys-
General specifications for anodic oxide coatings on
ISO 6361-3:1985: Wrought aluminium & aluminium alloy
aluminium
sheets, strips & plates - Part 3: Strips - Tolerances on
shape & dimensions ISO 7668:1986: Anodized aluminium & aluminium alloys-
Measurement of specular reflectance & specular gloss
ISO 6361-4:1988: Wrought aluminium & aluminium alloy
at angles of 20 degrees, 45 degrees, 60 degrees or 85
sheets, strips & plates - Part 4: Sheets & plates -
degrees
Tolerances on form & dimensions
ISO 7722:1985: Aluminium alloy castings produced by
ISO 6362-1: 1986 : Wrought aluminium & aluminium alloy gravity, sand, or chill casting, or by related processes -
extruded rods/bars, tubes & profiles - Part 1: Technical General conditions for inspection & delivery
conditions for inspection & delivery
ISO 7759:1983 : Anodizing of aluminium & its alloys-
ISO 6362-21990: Wrought aluminium & aluminium alloy Measurement of reflectivity characteristics of
extruded rods/bars, tubes & profiles - Part 2: aluminium surfaces using abridged goniophotometer or
Mechanical properties
goniophotometer
ISO 6362-3:1990: Wrought aluminium & aluminium alloy ISOIDIS 7866 : Refillable transportable seamless aluminium
extruded rods/bars, tubes & profiles - Part 3: Extruded
alloy gas cylinders for worldwide usage - Design,
rectangular bars - Tolerances on dimensions & form
construction & testing
ISO 6362-4:1988: Wrought aluminium & aluminium alloy ISO 8076: 1984 : Aerospace process - Anodic treatment of
extruded rods/bars, tubes & profiles - Part 4: Extruded aluminium alloys - Chromic acid process 40 V DC,
profiles - Tolerances on shape & dimensions
undyed coating
368 Appendix A - Standards
ISO (Aluminium) . continued. ISO 10546:1993 : Chemical conversion coatings - Rinsed &
ISO 8077:1984 : Aerospace process Anodic treatment of non-rinsed chromate conversion coatings on aluminium
aluminium alloys Chromic acid process 20 V DC, & aluminium alloys
undyed coating ISO 11040-3: 1993 : Prefilled syringes - Part 3: Aluminium
ISO 8078:1984 : Aerospace process - Anodic treatment of caps for dental local anaesthetic cartridges
aluminium alloys - Sulfuric acid process, undyed ISO 11678: 1996 : Agricultural irrigation equipment -
coating Aluminium irrigation tubes
ISO 8079: 1984 : Aerospace process - Anodic treatment of ISOfTR 11728:1993 : Anodized aluminium & aluminium
aluminium alloys - Sulfuric acid process, dyed coating alloys - Accelerated test of weather fastness of
ISO 8081: 1985 : Aerospace process - Chemical conversion coloured anodic oxide coatings using cyclic artificial
coating for aluminium alloys - General purpose light & pollution gas
ISOfTR 8125:1984: Anodizing of aluminium & its alloys- ISO 11846: 1995 : Corrosion of metals & alloys -
Determination of colour & colour difference of coloured Determination of resistance to intergranular corrosion
anodic coatings of solution heat-treatable aluminium alloys
ISO 8251 :1987 : Anodized aluminium & aluminium alloys - ISOIDIS 11881 : Corrosion of metals & alloys - Exfoliation
Measurement of wear resistance & wear index of corrosion testing of aluminium alloys
anodic oxidation coatings with an abrasive wheel wear ISOIDIS 13595 : Aerospace - Inserts, in aluminium alloy,
test apparatus coated or uncoated with self-locking floating nut, with
ISO 8252:1987: Anodized aluminium & aluminium alloys- MJ-threads, in metallic material, coated or uncoated -
Measurement of mean specific abrasion resistance of Dimensions
anodic oxidation coatings with an abrasive jet test ISOIDIS 13596 : Aerospace - Inserts, self-locking, with MJ-
apparatus threads, closed type, with or without helical coil insert,
ISO 8362-3: 1989 : Injection containers for injectables & coated m uncoated aluminium alloy, anodized -
accessories - Part 3: Aluminium caps for injection vials Dimensions
ISO 8536-3: 1992 : Infusion equipment for medical use - Part ISOIDIS 13597 : Aerospace - Inserts, self-locking, with MJ-
3: Aluminium caps for infusion bottles thread, open type, in aluminium alloy, coated or
uncoated - Dimensions
ISO 8591-1: 1989 : Aerospace - Wrought aluminium &
aluminium alloys - Inspection, testing & supply ISOIDIS 13598 : Aerospace - Inserts, self-locking, with MJ-
requirements - Part 1: General requirements thread, reduced flanges, closed type, in aluminium
alloy, coated or uncoated - Dimensions
ISO 8644:1988: Motorcycles - Light-alloy wheels - Test
method ISOIDIS 13599 : Aerospace - Inserts, with clearance hole, in
aluminium alloy, coated or uncoated - Dimensions
ISO 8645: 1988 : Mopeds - Light-alloy wheels - Test method
ISOIDIS 13770 : Aluminium alloy gas cylinders - Operational
ISO 8993:1989: Anodized aluminium & aluminium alloys- requirements for avoidance of neck & shoulder cracks
Rating system for the evaluation of pitting corrosion -
Chart method ISOIDIS 13919-2 : Welding & allied processes - Electron- &
laser-beam welded joints - Guidance on quality levels
ISO 8994:1989: Anodized aluminium & aluminium alloys- for imperfections - Part 2: Aluminium
Rating system for the evaluation of pitting corrosion -
Grid method
ISOIDIS 9018 : Specimen dimensions & procedure for
British Standards (BSI)
testing the static strength of fillet welds in structural BS 215 : Specification for aluminium stranded conductors &
steels & aluminium alloys steel-reinforced aluminium conductors for overhead
ISOIDIS 9418 : Aerospace - Aluminium & aluminium alloy power transmission
solid rivets - Procurement specification BS 215-1 : Aluminium stranded conductors (IEC 207)
ISO 9591: 1992 : Corrosion of aluminium alloys - BS 215-2 : Steel-reinforced aluminium conductors (IEC 209)
Determination of resistance to stress corrosion
BS 388 : SpeCification for aluminium pigments
cracking
BS 1133-21 : Packaging. Regenerated cellulose film, plastic
ISO 9915:1992 : Aluminium alloy castings - Radiography film, aluminium foil, flexible multilayer structures &
testing metallized materials
ISO 9916:1991 : Aluminium alloy & magnesium alloy BS 1161 : Specification for aluminium alloy sections for
castings - Liquid penetrant inspection structural purposes
ISO 10049:1992 : Aluminium alloy castings - Visual method BS 1470: Specification for wrought aluminium & aluminium
for assessing the porosity alloys for general engineering purposes - plate, sheet
ISO 10074: 1994 : Specification for hard anodic oxidation & strip (withdrawn; see EN 485-1 to -4; EN 515; EN
coatings on aluminium & its alloys 573-1 to -4)
ISO 10215:1992 : Anodized aluminium & aluminium alloys- BS 1471 : Specification for wrought aluminium & aluminium
Visual determination of image clarity of anodic alloys for general engineering purposes - drawn tube
oxidation coatings - Chart scale method BS 1472 : Specification for wrought aluminium & aluminium
ISO 10216:1992 : Anodized aluminium & aluminium alloys- alloys for general engineering purposes - forging stock
Instrumental determination of image clarity of anodic & forgings (partially replaced; see also EN 586-2)
oxidation coatings - Instrumental method
BS 1473: SpeCification for wrought aluminium & aluminium
ISO 10461:1993: Seamless aluminium-alloy gas cylinders- alloys for general engineering purposes - rivet, bolt &
Periodic inspection & testing screw stock
Appendix A - Standards 369
British Standards (Aluminium) - continued. BS 4300-6 : 3105 sheet & strip (withdrawn; replaced by BS
BS 1474: Specification for wrought aluminium & aluminium 1470)
alloys for general engineering purposes - bars, BS 4300-7: 5005 sheet & strip (withdrawn; replaced by BS
extruded round tubes & sections 1470)
BS 1475 : Specification for wrought aluminium & aluminium BS 4300-8 : 5454 plate, sheet & strip (withdrawn; replaced
alloys for general engineering purposes - wire by BS 1470)
BS 1476 : Wrought aluminium & aluminium alloys for BS 4300-9: NG 41 wire (withdrawn)
general engineering purposes - bars & sections BS 4300-10 : 5454 drawn tube
(withdrawn; see BS 1474)
BS 4300-11 : 5454 forging stock & forgings
BS 1477 : Wrought aluminium & aluminium alloys for
BS 4300-12: 5454 bars, extruded round tube & sections
general engineering purposes - plate (withdrawn; see
EN 485-1 to -4; EN 515; EN 573-1 to -4) BS 4300-13 : 5554 welding wire
BS 1490 (1988) : Specification for aluminium & aluminium BS 4300-14 : 7020 plate, sheet & strip (withdrawn)
alloy ingot & castings for general engineering purposes BS 4300-15 : 7020 bar, extruded round tube & sections
BS 1615: Method for specifying anodic oxidation coatings BS 4300-16 : 8011 specification for sheet & strip
on aluminium & its alloys (withdrawn; see EN 485-1 to -4; EN 515, EN 573-1 to-
BS 1616 : Aluminium electrodes for metal-arc welding 4)
(withdrawn) BS 4868 : Specification for profiled aluminium sheet for
BS 1974: Specification for large aluminium alloy rivets, 0.5 building (replaces BS 2855 & BS 3428)
inch to 1 inch nominal diameter (obsolete) BS 4872-2 : Specification for approval testing of welders,
BS 2006 : Specification for aluminium collapsible tubes when welding procedure approval is not required. TIG
or MIG welding of aluminium & its alloys
BS 2037 : Specification for portable aluminium ladders,
steps, trestles & lightweight stagings (see also EN 131 BS 4873 : Specification for aluminium alloy windows
-1 & -2) BS 5045-3 : Specification for seamless aluminium alloy gas
BS 2627 : Specification for wrought aluminium for electrical containers above 0.5 litre water capacity & up to 300
purposes - wire bar charged pressure at 15C
BS 2897 : Specification for wrought aluminium for electrical BS 5045-5 : Specification for aluminium alloy containers
purposes - strip with drawn or rolled edges above 0.5 litre water capacity & up to 130 litres water
capacity with welded seams
BS 2898 : Specification for wrought aluminium for electrical
purposes - bars, extruded round tube & sections BS 5045-6 : Specification for seamless containers of less
than 0.5 litre water capacity (aluminium & steel)
BS 2901-4 : Filler rods & wires for gas-shielded arc welding.
Specification for aluminium, aluminium alloys & BS 5286 : Specification for aluminium framed sliding glass
magnesium alloys doors
BS 2997 : Specification for aluminium rainwater goods BS 5430-3 : Periodic inspection, testing & maintenance of
BS 3242 : Specification for aluminium alloy stranded transportable gas containers - excluding dissolved
conductors for overhead power transmission (IEC 208) acetylene containers. Specification for seamless
aluminium alloy containers of water capacity 0.5 litres
BS 3313-1 : Specification for aluminium capping foil & strip & above.
for dairy product containers. Aluminium capping for
glass containers BS 5430-6 : Periodic inspection, testing & maintenance of
transportable gas containers - excluding dissolved
BS 3313-2 : Specification for aluminium capping foil & strip acetylene containers. Specification for seamless steel
for dairy product containers. Aluminium capping foil for & aluminium alloy containers of water capacity of less
skirted closures for plastics containers than 0.5 litres
BS 3660 : Glossary of terms used in the wrought aluminium BS 5599 : Specification for hard anodic oxidation coatings
industry (withdrawn; see EN23134 series) on aluminium & its alloys for engineering purposes
BS 3987 : Specification for anodic oxidation coatings on BS 6161 (parts 1 to 19): Methods of test for anodic
wrought aluminium for external architectural oxidation coatings on aluminium & its alloys
applications
BS 7365 : Specification for hard drawn aluminium wire for
BS 3988 : Specification for wrought aluminium for electrical overhead line conductors (lEC 889)
purposes. Solid conductors for insulating cables (refer
BS 8118 : Structural use of aluminium
also to IEC 121)
BS 8118-1 : Structural use of aluminium. Code of practice
BS 3989 : Specification for aluminium street lighting
for design (replaces CP118, which also remains active)
columns (withdrawn)
BS 8118-2 : Specification for materials, workmanship &
BS 4300 : Wrought aluminium & aluminium alloys for
protection (replaces CP118, which also remains active)
general engineering purposes (supplementary series)
BS 4300-1 : Aluminium alloy longitudinally welded tube BS CP Standards
BS 4300-2 : BTR S1 & BTR S2 sheet & strip suitable for
BS CP 118 : The structural use of aluminium (replaced by
bright trim/reflector applications (withdrawn)
BS 8118-1 & -2, but remains active to allow design
BS 4300-3 : Aluminium alloy suitable for bright trim/reflector overlap)
applications. Forgings (withdrawn)
BS CP 143-1 : Code of practice for sheet roof & wall
BS 4300-4 : 6463 solid extruded bars & sections suitable for coverings. Aluminium corrugated & toughed
bright trim/reflector applications
BS CP 143-15 : Code of practice for sheet roof & wall
BS 4300-5 : 2011 free-cutting bar & wire coverings. Aluminium metric units
370 Appendix A - Standards
BS L Standards BS 2L 93 : Specification for plate of AI-Cu-Mg-Si-Mn alloy,
solution treated, controlled stretch & precipitation
BS 6L 16 : Specification for sheet & strip of 99% aluminium, treated, Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8
temper H14 or H24
BS 2L 95 : Specification for plate of AI-Zn-Mg-Cu-Cr alloy,
BS 6L 17 : Specification for sheet & strip of 99% aluminium, solution treated, controlled stretch & precipitation
temper 0 treated, Zn 5.8, Mg 2.5, Cu 1.6, Cr 0.15
BS 5L 34 : Specification for forging stock, bars, extruded BS 2L 97 : Specification for plate of AI-Cu-Mg-Mn alloy,
sections & forgings of 99% aluminium solution treated, controlled stretch & aged at RT, Cu
BS 5L 36 : Specification for wire for solid, cOld-forged rivets 4.4, Mg 1.5, Mn 0.6
99.5% aluminium, not exceeding 10mm diameter BS 2L 98 : Specification for plate of AI-Cu-Mg-Mn alloy,
BS 5L 44 : Specification for forging stock, bars, extruded solution treated & aged at RT - no controlled stretch,
sections & forgings of AI-2.25%Mg alloy Cu 4.4, Mg 1.5, Mn 0.6
BS 3L 51 : Specification for ingots & castings of AI-Si-Cu- BS 2L 99 : Specification for ingots & castings of AI-Si-Mg
Fe-Ni-Mg alloy, precipitation treated, Si 2.5, Cu 1.2, Fe alloy, solution treated & precipitation treated, Si 7, Mg
1, Ni 1, Mg 0.1 (obsolete) 0.3
BS 4L 54 : Specification for tube of 99% aluminium, cold- BS 4L 100 : Procedure for inspection, testing & acceptance
drawn, seamless, tested hydraulically; not exceeding of wrought aluminium & aluminium alloys
12 mm wall thickness BS 4L 101 : Procedure for inspection, testing & acceptance
BS 4L 56 : Specification for tube of AI 2.25%Mg, temper 0, of aluminium-base & magnesium base ingots &
seamless, tested hydraulically; not exceeding 12 mm castings
wall thickness BS L 102 : Specification for bars & extruded sections of AI-
BS 3L 58 : Specification for wire for solid, cold-forged rivets Cu-Mg-Si-Mn alloy, solution treated & aged at RT; not
al AI-5%Mg, not exceeding 10mm diameter exceeding 200 mm diameter or minor sectional
BS 4L 59 : Specification for sheet & strip of AI-Mn alloy, dimension, Cu 4.4, Mg 0.5, Si 0.7, Mn 0,8 (replaced
temper H16 or H26 2L39, 6L 1, obsolete; see EN 2100)
BS 4L 60 : Specification for sheet & strip of AI-Mn alloy, BS L 103 : SpeCification for forging stock & forgings of AI-
temper H 12 or H22 Cu-Mg-Si-Mn alloy, solution treated & aged at RT, Cu
4.4, Mg 0.5, Si 0.7, Mn 0.8 (replaced 2L 39).
BS 4L 61 : Specification for sheet & strip of AI-Mn alloy,
temper 0 BS L 105 : Specification for tube of AI-Cu-Mg-Si-Mn alloy,
solution treated & aged at RT, not exceeding 10 mm
BS 3L 63 : Specification for tube al AI-Cu-Mg-Si-Mn alloy,
wall thickness
solution treated & precipitation treated, Cu 4.4, Mg 0.5,
Si 0.7, Mn 0.8 BS L 109 : SpeCification for aluminium coated sheet & strip
of AI-Cu-Mg-Mn alloy, solution treated & aged at RT,
BS 2L 77 : Specification for forging stock & forgings of AI-
Cu 4.4, Mg 1.5, Mn 0.6
Cu-Mg-Si-Mn alloy, solution treated & precipitation
treated, Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8 (replaces L 45) BS L 110 : Specification for aluminium coated sheet & strip
of AI-Cu-Mg-Mn alloy, supplied for solution treatment
BS 3L 78 : Specification ingots & castings of AI-Si-Cu-Mg
by end user, Cu 4.4, Mg 1.5, Mn 0.6
alloy, solution treated & precipitation treated, Si 5, Cu
1.2, Mg 0.5 BS L 111 : SpeCification for bars & extruded sections of AI-
Mg-Si-Mn alloy, solution treated & precipitation treated,
BS 3L 80 : Specification for sheet & strip of AI-225%Mg suitable for welding, Mg 0.8, Si 1, Mn 0.7
alloy, temper 0
BS L 112 : Specification for forging stock & forgings of AI-
BS 3L 81 : Specification for sheet & strip of AI-2.25% Mg Mg-Si-Mn alloy, solution treated & precipitation treated,
alloy, temper H16 or H26 suitable for welding, Mg 0.8, Si 1, Mn 0.7
BS 2L 83 : Specification for forging stock, bars, extruded BS L 113 : Specification for sheet & strip of AI-Mg-Si-Mn
sections & forgings of AI-Cu-Ni-Mg-Fe-Si alloy, solution alloy, solution treated & precipitation treated, suitable
treated & precipitation treated, Cu 2, Ni 1, Mg 1, Si 0.9, for welding, Mg 0.8, Si 1, Mn 0.7
Fe 0.9
BS L 114 : Specification for tube of AI-Mg-Si-Mn alloy,
BS 2L 84 : Specification for bars & extruded sections of AI- solution treated & preCipitation treated, not exceeding
Cu-Si-Mg alloy, solution treated & aged at RT, not 100 mm wall thickness, suitable for welding, Mg 0.8, Si
exceeding 200 mm diameter or minor sectional 1, Mn 0.7
dimension; Cu 1.5, Si 1, Mg 0.8
BS L 115 : Specification for plate of AI-Mg-Si-Mn alloy,
BS 2L 85 : Specification for forging stock, bars, extruded solution treated, controlled stretch & precipitation
sections & forgings of AI-Cu-Si-Mg alloy, solution treated, not exceeding 25mm thick, suitable for welding
treated & precipitation treated; Cu 1.5, Si 1, Mg 0.8 Mg 0.8, Si 1, Mn 0.7
BS 3L 86 : Specification for wire for solid, cOld-forged rivets BS 2L 116 : Specifiction for tube of 99% aluminium, cold
of AI-Cu-Mg alloy, not exceeding 10mm diameter; Cu drawn, seamless, not tested hydraulically; not
2.5, Mg 0.3 exceeding 12 mm wall thickness
BS 2L 87 : Specification for hexagonal bars for nuts, BS L 117 : Specification for tube of AI-Mg-Si-Cu-Cr all.oy,
couplings & hollow machined parts of AI-Cu-Mg-Si-Mn solution treated & artificially aged, tested hydraulically,
alloy, solution treated & precipitation treated, free from not exceeding 10 mm thickness, Mg 1.0, Si 0.6, Cu
peripheral & asymmetric coarse grain; not less than
0.28, Cr 0.2
14mm nor more than 36 mm across flats
BS L 118 : Specification for tube of AI-Mg-Si-Cu-Cr alloy,
BS 2L 88 : Specification for aluminium alloy coated sheet & solution treated & artificially aged, tested hydraulically,
strip for AI-Zn-Mg-Cu-Cr alloy, solution treated & not exceeding 10 mm thickness, Mg 1.0, Si 0.6, Cu
precipitation treated, Zn 5.8, Mg 2.5, Cu 1.6, Cr 0.15
0.28, Cr 0.2
Appendix A - Standards 371
British Standards "L" (Aluminium) - continued. BS L 171 : Specification for forging of AI-Zn-Mg-Mn-Cu
BS L 119 : Specification for ingots & castings of AI-Cu-Ni- alloy, supplied as-forged or annealed for subsequent
Mn-Ti-Zr-Co-Sb alloy, solution treated & artificially heat treatment, not exceeding 150 mm diameter or
aged, Cu 5.0, Ni 1.5, Mn 0.25, Ti 0.2, Zr 0.2, Co 0.2, minor sectional dimension, Zn 5.7, Mg 2.7, Mn 0.5, Cu
Sb 0.2 0.5, (7014)
BS L 154 : Specification for ingots & castings of AI-Cu-Si BS L 172 : Specification for extruded, rolled or cast forging
alloy, solution treated & aged at RT, Cu 4, Si 1 stock of AI-Zn-Mg-Mn-Cu alloy, for manufacture
forgings to BS L 171, Zn 5.7, Mg 2.7, Mn 0.5, Cu 0.5,
BS L 155 : Specification for ingots & castings of AI-Cu-Si
(7014)
alloy, solution treated & artificially aged, Cu 4, Si 1
BS L 173 : Specification for castings of AI-Si-Mg alloy, chill
BS L 156 : Specification for sheet & strip of AI-Cu-Mg-Si-Mn
cast, solution treated & precipitation treated to an
alloy, solution treated & aged at RT, Cu 4.4, Mg 0.5, Si
overaged, T7, condition
0.8, Mn 0.8 (replaces BS 5L 3, 3L 70 & BS L 106)
BS L 174 : Specification for castings of AI-Si-Mg alloy, sand
BS L 157 : Specification for sheet & strip of AI-Cu-Mg-Si-Mn
cast, solution treated & precipitation treated to an
alloy, solution treated & artificially aged, Cu 4.4, Mg
overaged, T7, condition
0.5, Si 0.8, Mn 0.8 (replaces BS L 150)
BS L 158 : Specification for close toleranced sheet & strip of BS SP Standards
AI-Cu-Mg-Si-Mn alloy, solution treated & aged at RT,
Cu 4.4, Mg, 0.5, Si 0.8, Mn 0.8 BS SP 65 : Specification for aluminium alloy taper pins for
aeronautical purposes (replaces SP 28, 29, 30)
BS L 159 : Specification for close toleranced sheet & strip of
AI-Cu-Mg-Si-Mn alloy, solution treated & artificially BS 2SP 68 to 2SP 71 : Specification for 100 countersunk
aged, Cu 4.4, Mg, 0.5, Si 0.8, Mn 0.8 precision head aluminium & aluminium alloy rivets
BS L 160 : Specification for bars & extruded sections of AI- BS 2SP 77 to 2SP 80 : Specification for snap head
Zn-Mg-Si-Mn, solution treated & artificially overaged, aluminium 7 aluminium alloy rivets
Zn 5.6, Mg 2.5, Cu 1.6, Cr 0.22 (obsolete; replaced by BS 2SP 83 to SP 85 : Specification for mushroom head
EN 2127) aluminium alloy rivets
BS L 161 : Specification. Hand- & die-forgings of AI-Zn-Mg- BS 2SP 142 : Specification for solid rivets with 100
Cu-Cr, solution treated & artificially overaged, , Zn 5.6, countersunk truncated radiused head made from BS L
Mg 2.5, Cu 1.6, Cr 0.22 86 material
BS L 162 : Specification. Cold compressed hand forgings of BS SP 143 : Specification for solid rivets with 100
AI-Zn-Mg-Cu-Cr, solution treated & artificially countersunk truncated radiused head made from BS L
overaged, , Zn 5.6, Mg 2.5, Cu 1.6, Cr 0.22 37 material
BS L 163 : Specification for sheet & strip of aluminium- BS 2SP 157-163 : Specification for solid rivets with universal
coated AI-Cu-Mg-Si-Mn, solution treated, cold worked head made from BS L 86 (SP 157 & SP 163), BS L 58
for flattening & aged at RT, Cu 4.4, Mg 0.5, Si 0.8, Mn (SP160 & SP 161), BS L 37 (SP 162) & DTD 204 (SP
0.8 (replaces BS 2L 38, 3L 72) 158 & 159) materials
BS L 164 : Specification for sheet & strip of aluminium-
BS DID Standards
coated AI-Cu-Mg-Si-Mn, solution treated & aged at RT,
Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8 (replaces BS L 151 7 BS MOD (Aviation Supply) Department of Trade and Industry,
L 153) Aerospace Material Specification Alloys.
BS L 165 : Specification for sheet & strip of aluminium-
coated AI-Cu-Mg-Si-Mn, solution treated & artificially Compiled from information provided by ALFED - Aluminium
aged, Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8 (replaces BS L Federation (UK) and OEA (Organisation of European
152) Aluminium Refiners & Remelters).
BS L 168 : Specification for bars & extruded sections of AI- 106 : Withdrawn
Cu-Mg-Si-Mn, solution treated & artificially aged not 110 : Replaced by 7L37
exceeding 200 mm diameter or minor sectional 111 : Replaced by L 163
dimension, Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8 (replaces BS
128 : Withdrawn
2L40, L45, 3L 65)
130B : Replaced by 2L83
BS L 169 : Specification for ingots & castings of AI-Si-Mg
alloy, solution treated & artificially aged, Si7, Mg 0.6 131 B : Replaced by 3L52
BS L 170 : Specification for extruded bars & sections of AI- 132 : Withdrawn
Zn-Mg-Cu-Cr, solution treated, controlled stretch & 133C : Replaced by 3L51 (Obsolete)
artificially aged, not exceeding 150 mm diameter or
147: Withdrawn
minor sectional dimension, Zn 5.6, Mg 2.5, Cu 1.6, Cr
0.22; 7075 148: Replaced by 5L36
150A : Forging stock and forgings
165A : Withdrawn
372 Appendix A - Standards
British Standards "DTD" (Aluminium) - continued. 342 : Replaced by L 165
170A : Withdrawn 346A : Replaced by L 113 (in soft condition)
175A : Withdrawn 351 : Replaced by L 165
177A : Withdrawn 356 : Replaced by L 157
179A : Withdrawn 361 B : Withdrawn
180C : Withdrawn 363A : Replaced by DTD 5124
182B : Withdrawn 364B : Replaced by L 168
184 : Withdrawn 372B : 6063 Bars and sections
186B : Withdrawn 390 : Replaced by L 163
190 : Withdrawn 404 : Withdrawn
191 : Withdrawn 410 : Replaced by 2L83
194 : Withdrawn 423C: Replaced by 2L85
198A : Withdrawn 424A : Withdrawn
202 : Replaced by BS1453-5056A 428 : Withdrawn
206 : Withdrawn 440 : Withdrawn
209A : Replaced by 3L80 443A : Replaced by 2L84
213A : Replaced by 4L59 450A : Withdrawn
220A : Withdrawn 460A : Withdrawn
231 : Withdrawn 464A : Replaced by 3L63
238 : Withdrawn 478 : Withdrawn
240 : Withdrawn 479 : Withdrawn
243 : Withdrawn 520 : Withdrawn
245A : Withdrawn 543A : Withdrawn
246C : Forging stock and forgings 546B : Replaced by L 165
248 : Withdrawn 603B : Replaced by L 156
249 : Withdrawn 606A: Replaced by 3L81
250 : Withdrawn 610B : Replaced by L 163
252 : Replaced by L 168 634A : Replaced by 3L80
255 : Replaced by 3L52 635A : Withdrawn
264A : Withdrawn 646B : Replaced by L 157
266 : Withdrawn 653 : Replaced by 4L60
269 : Withdrawn 683A: Replaced by DTD 5024, 5114, 5044
270 : Withdrawn 687B : Replaced by 2L88
272A : Withdrawn 693 : Withdrawn
273 : Withdrawn 706 : Withdrawn
275 : Withdrawn 710B : Replaced by L 166
276A: Replaced by 3L78 716B (1971) : Ingots and castings
278 : Replaced by 3L80 717A: 2618A Forging stock and forgings
280 : Withdrawn 722B (1971) : Ingots and castings
287 : Replaced by 3L51 (Obsolete) 724 : Withdrawn
290 : Withdrawn 727B (1971) : Ingots and castings
292 : Replaced by 3L80 731 B : 2618A Forging stock and forgings
293 : Replaced by 2L83 735B (1971) : Ingots and castings
294 : Withdrawn 741 A : Withdrawn
296 : Withdrawn 745A : 2618A Forging stock and forgings
297 A : Forging stock and forgings 746C : Replaced by L 167
298B : Replaced by 2L91 5004A : Forging stock and forgings
300A : Replaced by 4L53 5008B (1971) : Ingots and castings
303 : Replaced by 3L58 5009 : Withdrawn
304B : Replaced by 2L92 5010A: 2014A Plate
309 : Withdrawn 5014A : 2618A Bars and sections
310C: Replaced by 3L56 (4L56) 5018A (1971) : Ingots and castings
313: Withdrawn 5020A : Replaced by 2L93
324B : Forging stock and forgings 5024: 7014 Forging stock and forgings
327 : Replaced by 3L86 5028: Replaced by 2L99
Appendix A - Standards 373
British Standards "OTO" (Aluminium) - continued. DIN 1769 Wrought aluminium & aluminium alloy drawn
5030A 2014A Clad plate rectangular bars with square edges, tolerances on
dimensions & forms, static values
5034 Withdrawn
DIN 1770 Wrought aluminium & aluminium alloy extruded
5040A 2014A Clad plate
rectangular bars, tolerances on dimensions & forms,
5044.7014 Bars and sections static values
5050B Replaced by 2L95 DIN 1771 Aluminium & wrought aluminium alloy, extruded
5054A Replaced by DTD 5114 angles, dimensions, static values
5060A Replaced by DTD 5110 DIN 1783 Wrought aluminium & aluminium alloy strips,
plates & sheets with thicknesses >0.35 mm, cold-
5064 Withdrawn
rolled, dimensions
5070B 2618A Clad sheet and strip
DIN 1784 Wrought aluminium & aluminium alloy strips,
5074A. Replaced by DTD 5124 plates & sheets with thicknesses from 0.021 to 0.35
5080 Replaced by L 113 mm, cold-rolled, dimensions
5084A 2618A Forging stock and forgings DIN 1784-3. Aluminium coiled strips & foils from 0.007 to
5090 Replaced by 2L97 and 2L98 0.020 mm [7-20 microns), cold-rolled, dimensions
5094A 7014 Forging stock and forgings DIN 1788 Wrought aluminium & aluminium alloy strip &
sheet with thicknesses from 0.021 to 0.35 mm, cold-
5100A. 2024 Clad plate rolled, properties
5104. Part replaced by L 172 DIN 1790 Wrought aluminium & aluminium alloy wire
5104A. 7014 Forging stock and forgings DIN 1795 Wrought aluminium & aluminium alloy, seamless
5110. 7014, 7075 Clad plate drawn round tubes, dimensions, tolerances on
5114 Bars and sections dimensions & forms; Supplement 2 - tolerances on
preferred sizes
5120B 7010 Plate
DIN 1796 Wrought aluminium & aluminium alloy, drawn
5124 7075 Bars and sections
square bars with sharp edges, dimensions, tolerances
5124 Part replaced by L 170 on dimensions & forms
5130A 7010 Plate DIN 1797 Wrought aluminium & aluminium alloy, drawn
5636 7010 Forgings hexagonal bars with sharp edges, dimensions,
tolerances on dimensions & forms
DIN Standards DIN 1798 Wrought aluminium & aluminium alloy, drawn
round bars, dimensions, tolerances on dimensions &
DIN 1712-1 Aluminium - ingots forms
DIN 1712-3 Aluminium - semi-finished products DIN 1799 Wrought aluminium & aluminium alloy, extruded
DIN 1725-1 Wrought aluminium alloys round bars, dimensions, tolerances on dimensions &
forms
DIN 1725-2 Casting aluminium alloys, by sand, gravity die,
pressure die, investment DIN EN 2004-1, Publication. 1993-09 Aerospace series;
DIN 1725-2-Supp. 1 Casting aluminium alloys, by sand, test methods for aluminium & aluminium alloy products;
part 1. determination of electrical conductivity of
gravity die, pressure die, investment - mechanical &
wrought aluminium alloys; German version EN 2004-
physical properties, with notes on casting techniques
11993.
DIN 1725-3 Master aluminium alloys
DIN EN 2004-4 (Norm-Entwuri), Publication.1992-10
DIN 1725-5. Casting aluminium alloys, ingots [pigs), liquid Aerospace series; test methods for aluminium &
metal, composition aluminium alloys products; part 4. stress corrosion test
DIN 1725-5-Supp. 1 Casting aluminium alloys, ingots by alternate immersion for high strength aluminium
[pigs], liquid metal, composition - alloying processes alloy wrought products.
DIN 1745 Wrought aluminium & aluminium alloy plate, DIN EN 2004-5, Publication 1993-09 Aerospace series;
sheet & strip >0.35 mm thickness test methods for aluminium & aluminium alloy products;
01 N 1746 Wrought aluminium & aluminium alloy tubes part 5. determination of cladding thickness & copper
diffusion of clad semi-finished products; German
DIN 1747. Wrought aluminium & aluminium alloy rod & bar
version EN 2004-5.1993.
DIN 1748. Wrought aluminium & aluminium alloy extruded
DIN EN 2004-7 (Norm-Entwuri), Publication.1996-07
sections Aerospace series - Test methods for aluminium &
DIN 1748-3. Aluminium extruded sections, highest grade aluminium alloy products - Part 7 Reference blocks for
AI, High grade AI & wrought AI-alloys - design the calibration of measuring equipment used in the
DIN 1748-4. Wrought aluminium & aluminium alloy determination of electrical conductivity of wrought
extruded profiles - permissible deviations aluminium & aluminium alloys.
DIN 1749: Drop forgings of aluminium & wrought aluminium DIN EN 2004-10 (Norm-Entwuri), Publication.1994-05
alloys Aerospace series; test methods for aluminium &
aluminium alloy products; part 10. preparation of
DIN 17606. Open die forgings of wrought aluminium alloys
micrographic specimens for aluminium alloys.
DIN 17611 Anodized wrought aluminium & aluminium
DIN EN 2599 (Norm-Entwuri), Publication.1996-05 :
alloys semi-finished products, with coating thickness at
Aerospace series - Strip in aluminium & aluminium
least 10 microns, technical delivery conditions
alloys - Thickness 0 25 mm <a> 3, 2 mm; dimensions.
DIN 17615. AIMgSiO.5 precision sections
374 Appendix A - Standards
DIN Standards (Aluminium) - continued. DIN 40501-1 : Aluminium for electrical purposes: E-AI plate,
DIN EN 2615 (Norm-Entwurf), Publication:1990-08 : sheet & strip
Aerospace series; wire to close tolerance in aluminium DIN 40501-2 : Aluminium for electrical purposes: E-AI & E-
& aluminium alloys 1.6 D 9.6 mm; dimensions. AIMgSiO.5 tubes
DIN EN 2616 (Norm-Entwurf), Publication:1990-08 : DIN 40501-3 : Aluminium for electrical purposes: E-AI & E-
Aerospace series; wire for rivets in aluminium & AIMgSiO.5 bars & sections
aluminium alloys, large tolerances D 10 mm; DIN 40501-4 : Aluminium for electrical engineering. Pure
dimensions. aluminium wires
DIN 5513, Publication:1989-02: Materials for rail vehicles; DIN 46420 : Aluminium for electrical purposes. Round,
aluminium & aluminium alloys. drawn wire, dimensions
DIN 8513-4 : Brazing & braze weld filler metals. aluminium- DIN 46424 : Switch-gear. Extruded channel sections for
base brazing alloys. busbars
DIN 9107 : Wrought aluminium & aluminium alloy, seamless DIN 46425 : Aluminium for electrical purposes. Round,
extruded round tubes, dimensions, tolerances on exactly-drawn wire, dimensions
dimensions & forms
DIN 50939 : Corrosion protection, chromating of aluminium,
DIN 9712: Aluminium & Magnesium beams, extruded, principles & test methods
dimensions, static values
DIN 50949 : Nondestructive testing of anodic oxidation
DIN 9713 : Aluminium & wrought aluminium alloy, extruded coatings on pure aluminium & aluminium alloys by
channel sections, dimensions, static values measurement of admittance
DIN 9714 : Aluminium & wrought aluminium alloy, extruded DIN 59600 : Strips, plates & sheets of aluminium & wrought
T-sections, dimensions, static values aluminium alloys, hot-rolled, dimensions
DIN EN 12373-3 (Norm-Entwurf), Publication: 1996-11 DIN 59604 : Wrought aluminium & aluminium alloy slugs for
Aluminium & aluminium alloys - Anodizing - Part 3: impact extrusion
Estimation of loss of absorptive power of anodic
oxidation coatings after sealing; dye spot test with prior DIN 59605: Embossed plate & sheet of wrought aluminium
acid treatment; German version prEN 12373-3: 1996. alloy
DIN EN 12373-5 (Norm-Entwurf), Publication: 1996-11 DIN 59606 : Wrought aluminium & aluminium alloy sheet &
Aluminium & aluminium alloys - Anodizing - Part 5: strip for cans & sealing caps
Assessment of quality of sealed anodic oxidation DIN 59675 : High grade aluminium & wrought aluminium
coatings by measurement of the loss of mass after alloy wire & bars for rivets, drawn
immersion in phosphoric acid/chromic acid solution DIN 59700 : Wrought aluminium & aluminium alloy,
without prior acid treatment; German version prEN extruded square bars, dimensions, tolerances on
12373-5: 1996. dimensions & forms
DIN EN 12373-6 (Norm-Entwurf), Publication:1996-11 : DIN 59701 : Wrought aluminium & aluminium alloy,
Aluminium & aluminium alloys - Anodizing - Part 6: extruded hexogonal bars, dimensions, tolerances on
Assessment of quality of sealed anodic oxidation dimensions & forms
coatings by measurement of the loss of mass after
DIN 59751 : Wrought aluminium, tubes & hollow hexagonal
immersion in phosphoric acid/chromic acid solution
sections, for free-cutting machining on automatics,
with prior acid treatment; German version prEN 12373-
seamless drawn, dimensions
6:1996.
DIN 65207 : Aerospace: Tolerances for wrought aluminium
DIN EN 12373-7 (Norm-Entwurf), Publication:1996-11 :
alloy folded profiles/sections
Aluminium & aluminium alloys - Anodizing - Part 7:
Determination of the comparative fastness to ultra- DIN 65582 : Aerospace Heat treatment of aluminium- &
violet light & heat of coloured anodic oxidation magnesium-alloy castings
coatings; German version prEN 12373-7: 1996. DIN V 65900-4 : Aerospace: Metallic materials - relationship
DIN EN 12373-11 (Norm-Entwurf), Publication: 1997-02 : between AECMA designation system (AECMA-TR-
Aluminium & aluminium alloys - Anodizing - Part 11: 3900: 1993)
Measurement of specular reflectance & specular gloss
of anodic oxidation coatings at angles of 20, 45, 60
German LN Standards
oder 85; German version prEN 12373-11: 1996. LN 1795 : Aerospace: Structural tubes in wrought aluminium
DIN EN 12373-13 (Norm-Entwurf), Publication:1997-02: alloys, seamless drawn, dimension & masses
Aluminium & aluminium alloys - Anodizing - Part 13: LN 1796 : Aerospace: Square bars of wrought aluminium
Measurement of reflectance characteristics of alloys, drawn, dimension & masses
aluminium surfaces using integrating-sphere
LN 1797 : Aerospace: Hexagonal bars of wrought aluminium
instruments; German version prEN 12373-13: 1996.
alloys, drawn, dimensions & masses
DIN 29531, Publication:1990-09: Aerospace; castings of
LN 1798 : Aerospace: Round bars of wrought aluminium
aluminium & magnesium alloys; technical speCification.
alloys, drawn, dimension & masses
DIN 29547 : Aerospace: Seamless structural tubes in
LN 1799 : Aerospace: Round bars of wrought aluminium
wrought aluminium alloys (obsolete)
alloys, extruded, dimension & masses
DIN 29850 : Aerospace: Heat treatment of wrought
LN 9073 : Aerospace: Sheet & plate in wrought aluminium
aluminium alloys
alloys, standard plane, rolled, dimension & masses
DIN 29850 : Aerospace: Heat-treatment of wrought
LN 9074 : Aerospace: Sheet & plate in wrought aluminium
aluminium alloys
alloys, skin quality, rolled, dimension & masses
Appendix A - Standards 375
German LN Standards (Aluminium) - continued, NF A 02-004 AoOt 1977 : Aluminium et alliages d'aluminium
LN 9087 : Aerospace: Extruded profiles, beaded angles, in de fonderie. Zinc et alliages de zinc de fonderie.
wrought aluminium alloys dimensions, static values, Magnesium et ses alliages. Designation
masses conventionnelle des materiaux. Statut :Enregistree
LN 9410 : Aerospace: Wedge sections, extruded, in wrought A 02-011 Novembre 1970 : Aluminium et alliages
aluminium alloys, dimension & masses d'aluminium. Vocabulaire des traitements thermiques
et mecaniques .. Statut :Fascicule de doc.
LN 9411 : Aerospace: Folded profile, angle in wrought
aluminium alloys, dimensions, static values, masses A 02-114 Octobre 1987 : Aluminium et alliages d'aluminium.
Correspondance entre la designation normalisee
LN 9412 : Aerospace: Folded profile, angle with internally
lipped flanges, in wrought aluminium alloys, dimension,
a
utilisee en France et I'etranger .. Statut :Fascicule de
doc.
static values, masses
NF A 03-253 Avril 1972 : Aluminium et alliages d'aluminium
LN 9413: Aerospace: Folded profile, channel, in wrought - Cuivre et alliages de cuivre. Essai de durete Vickers -
aluminium alloys, dimension, static values, masses Charges comprises entre 0,2 kgf et 120 kgf
LN 9414 : Aerospace: Folded profile, channel with internally Statut :Enregistree
lipped flanges, in wrought aluminium alloys, dimension,
NF A 03-260 Avril 1972 : Aluminium et alliages d'aluminium
static values, masses
- Cuivre et alii ages de cuivre. Essai de pliage simple
LN 9415 : Aerospace: Folded profile, Z-section with one Statut :Enregistree
lipped flange, in wrought aluminium alloys, dimension,
NF A 03-268 Octobre 1971 : Aluminium et alliages
static values, masses d'aluminium - Cuivre et alliages de cuivre. Essai de
LN 9416 : Aerospace: Folded profile, LZ-section, in wrought torsion simple des fils Statut :Enregistree
aluminium alloys, dimension, static values, masses
NF A 04-150 Novembre 1984: Produits de fonderie-
LN 9417: Aerospace: Folded profile, top hat section, in Contrale par radiographie des pieces moulees en
wrought aluminium alloys, dimension, static values, alliages d'aluminium et de magnesium.
masses Statut :Homologuee
LN 9419 : Aerospace: Folded profile, bowler hat section, in Projet A 04-190 Avril 1997 : Fonderie Controle Par
wrought aluminium alloys, dimension, static values, Radiographie Projet
masses
NF A 04-503 Juillet 1988 : Demi-produits en aluminium,
LN 9496 : Aerospace: Extruded profile, angle, in wrought cuivre, nickel et leurs alliages. Determination de la
aluminium alloys, dimension, static values, masses grosseur de grain. Aluminium et alliages d'aluminium.
LN 9497 : Aerospace: Extruded profile, T-section, in Statut :Homologuee
wrought aluminium alloys, dimension, static values, NF A 04-505 Juillet 1988 : Demi-produits en aluminium,
masses cuivre, nickel et leurs alliages. Determination de la
LN 9498 : Aerospace: Extruded profile, channel section, in grosseur de grain. Nickel et nickels allies.
wrought aluminium alloys, dimension, static values, Statut :Homologuee
masses NF A 05-301 Septembre 1981 : Alliages d'aluminium - Essai
LN 29545 : Aerospace: Wedges in wrought aluminium de corrosion sous contrainte des produits epais
alloys, dimension & masses Statut :Enregistree
LN 29557-3: Aerospace: Laminated shim of wrought NF A 05-306 Decembre 1984 : Alliages d'aluminium (serie
aluminium & aluminium alloys, dimensions, masses 5XXX) - Essai de corrosion feuilletante.
Statut :Homologuee
AFNOR Standards Projet A 05-520 Juin 1993 : Corrosion Des Alliages
D'aluminium Determination De La Resistance A La
Corrosion Fissurante Sous Contrainte Projet
NF Standards
NF L 06-383 Novembre 1987 : Assemblages soudes et
Projet A 00-500-4 AoOt 1996 : Fonderie Conditions brases pour constructions aerospatiales. Assemblages
Techniques de Fourniture Partie 4 : Specifications a
soudes par resistance par points ou la moletie.
Complementaires Pour Les Pieces Moulees En Qualite des assemblages soudes. Statut :Homologuee
Alliages D'aluminium Projet
NF L 06-510 AoOt 1983 : Selection des fraises cylindriques
NF A 00-501-3 Mars 1991 : Produits de fonderie. Conditions a a
deux tailles queue, utiliser dans I'industrie
techniques generales de commande et de fournitures. aerospatiale, pour I'usinage en commande numerique
Partie 3 : pieces moulees par gravite, basse pression des alliages d'aluminium .. Statut :Homologuee
et depreSSion, en alliages d'aluminium et en alliages de
NF A 06-551 Octobre 1976 : Analyse chimique de
magnesium. Statut :Homologuee
I'aluminium et des alliages d'aluminium. Dosage
NF A 01-010 Octobre 1971 : Aluminium et alliages spectrophotometrique du cuivre (methode au
d'aluminium. Cuivre et alliages de cuivre. EChantilions cuprazon). Statut :Enregistree
specimens et eprouvettes pour essais.
NF A 06-552 Juillet 1964 : Analyse chimique de I'aluminium
Statut :Enregistree
et des alliages d'aluminium. Dosage du cuivre.
NF F 01-820 Fevrier 1992 : Materiel roulant ferroviaire. Statut :Homologuee
Joints soudes de produits en alliage d'aluminium pour
NF A 06-553 Avril 1966 : Analyse chimique de I'aluminium
ossature de caisse. Caracterisation.
et des alii ages d'aluminium. Dosage du zinc.
Statut :Homologuee
Statut :Homologuee
A 06-554 Mai 1966: Analyse chimique de I'aluminium et des
alliages d'aluminium. Dosage polarographique du zinc.
Statut :Fascicule de doc.
376 Appendix A - Standards
AFNOR NF Standards (Aluminium) - continued. NF A 06-588 Novembre 1970 : Analyse chimique de
A 06-563 Avril 1971 : Analyse chimique des alliages I'aluminium et des alliages d'aluminium. Dosage
d'aluminium - Dosage spectrophotometrique de spectrophotometrique du vanadium. Statut :Enregistree
I'antimoine. Statut :Fascicule de doc. NF A 06-602 Decembre 1984 : Analyse chimique des
NF A 06-564 Decembre 1969: Analyse chimique des alliages de titane. Dosage de I'aluminium dans les
alliages d'aluminium anti-friction - Dosage volumetrique alliages Ti-AI-V. Methode titrimetrique par I'EDTA
de I'etain. Statut :Enregistree Statut :Homologuee
NF A 06-568 Novembre 1971 : Analyse chimique de NF A 06-998 Decembre 1960 : Analyse chimique des
I'aluminium et des alliages d'aluminium. Dosage alliages d'imprimerie Statut :Homologuee
spectrophotometrique de I'etain. Statut :Enregistree NF L 07-152 Mai 1974 : Representation symbolique sur les
A 06-569 Fevrier 1972 : Analyse chimique de I'aluminium et dessins du diametre des rivets en alliages d'aluminium.
des alliages d'aluminium. Dosage Statui :Homologuee
spectrophotometrique de I'etain. Statut :Fascicule de A 07-500 Juin 1979 : Analyse par spectrometrie d'emission
doc. de I'aluminium et de ses alliages (emission par
NF A 06-570 Juillet 1964: Analyse chimique de I'aluminium etincelle). Statut :Fascicule de doc.
et des alliages d'aluminium. Dosage du silicium total. A 07-510 + F 1.2 Juin 1971 : Analyse des aluminiums non
Statut :Homologuee allies par spectrographie d'emission. Statut :Fascicule
NF A 06-571 Juillet 1964: Analyse chimique de I'aluminium de doc.
et des alliages d'aluminium. Dosage A 07-515 Juin 1971 : Analyse des alliages aluminium-cuivre
spectrophotometrique du fer. Statut :Homologuee par spectrographie d'emission. Statut :Fascicule de
NF A 06-574 Avril 1966 : Analyse chimique de I'aluminium doc.
et des alliages d'aluminium. Dosage A 07-520 Juin 1971 : Analyse des alliages aluminium-
spectrophotometrique du titane. Statut :Homologuee silicium et aluminium-silicium-cuivre par spectrographie
NF A 06-575 Mai 1971 : Analyse chimique des alliages d'emission. Statut :Fascicule de doc.
d'aluminium - Dosage gravimetrique du nickel. A 08-001 Avril 1979 : Analyse chimique des metaux et
Statut :Homologuee alliages legers - Application de la spectrometrie
NF A 06-576 Avril 1966 : Analyse chimique de I'aluminium d'absorption atomique a I'analyse de I'aluminium, du
et des alliages d'aluminium. Dosage magnesium et de leurs alliages. Statut :Fascicule de
spectrophotometrique du manganese. doc.
Statut :Homologuee A 08-547 Juin 1979 : Analyse chimique de I'aluminium et de
NF A 06-577 Decembre 1984 : Analyse chimique de ses alliages. Dosage du plomb - Methode par
I'aluminium et des alliages d'aluminium. Dosage absorption atomique. Statut :Fascicule de doc.
colorimetrique du cobalt. Statut :Homologuee A 08-553 Juillet 1979 : Analyse chimique de I'aluminium et
NF A 06-579 Avril 1966 : Analyse chimique de I'aluminium de ses alliages. Dosage du zinc - Methode par
et des alliages d'aluminium. Dosage du magnesium. absorption atomique. Statut :Fascicule de doc.
Statut :Homologuee A 08-556 Avril 1979 : Analyse chimique de I'aluminium et de
A 06-580 Septembre 1965 : Analyse chimique de ses alliages. Dosage du chrome - Methode par
I'aluminium et des alliages d'aluminium. Dosage absorption atomique. Statut :Fascicule de doc.
polarographique du cadmium. Statut :Fascicule de doc. A 08-563 Decembre 1974 : Analyse chimique des alliages
NF A 06-581 Decembre 1984 : Analyse chimique de d'aluminium. Dosage a I'antimoine - Methode par
I'aluminium et des alliages d'aluminium. Dosage absorption atomique. Statut :Fascicule de doc.
colorimetrique du chrome. Statut :Homologuee A 08-568 Decembre 1974 : Analyse chimique des alliages
NF A 06-582 Avril 1959 : Analyse chimique de I'aluminium d'aluminium. Dosage de I'etain - Methode par
et des alliages d'aluminium. Dosage absorption atomique. Statut :Fascicule de doc.
spectrophotometrique du zirconium. NF A 08-650 Octobre 1992 : Analyse chimique du titane et
Statut :Homologuee alliages de titane. Dosage des elements aluminium,
NF A 06-583 Decembre 1984 : Analyse chimique de vanadium et fer dans les alliages de nuance TA6V.
I'aluminium et des alliages d'aluminium. Dosage Methode par spectrometrie d'absorption atomique dans
spectrophotometrique du bismuth. Statut :Homologuee la flamme ou par spectrometrie d'emission de plasma.
Statut :Homologuee
NF A 06-584 Decembre 1984 : Analyse chimique de
I'aluminium et des alliages d'aluminium. Dosage NF A 08-651 Decembre 1993: Analyse chimique du titane
spectrophotomelrique du beryllium. et alliages de titane. Dosage des elements en faible
teneur dans les alii ages de nuance TA6V. Methode par
Statut :Homologuee
spectrometrie d'absorption atomique dans la flam me
NF A 06-585 Juin 1965 : Analyse chimique de I'aluminium et ou par spectrometrie d'emission de plasma.
des alliages d'aluminium. Dosage du plomb. Statut :Homologuee
Statut :Homologuee
L 09-775 + ERRATUM Octobre 1984: Codification des
NF A 06-586 Mai 1965 : Analyse chimique de I'aluminium et references relatives aux produits semi-ouvres en
des alliages d'aluminium. Dosage metaux et alliages non ferreux, normalises,
spectrophotometrique du bore. Statut :Enregistree selectionnes pour les constructions aeronautiques
NF A 06-587 Juin 1965 : Analyse chimique de I'aluminium et Statut :Fascicule de doc.
des alliages d'aluminium. Dosage du mercure. L 09-776 Octobre 1984 : Codification des references
Statut :Homologuee relatives aux produits semi-ouvres en alii ages
d'aluminium et titane, normalises, selectionnes pour les
constructions aeronautiques. Statut :Fascicule de doc.
Appendix A - Standards 377
AFNOR NF Standards (Aluminium) - continued. NF L 19-001 Decembre 1995 : Serie aerospatiale.
NF L 10-470 Novembre 1982 : Conditions de contrale et Materiaux alveolaires a cellules tubulaires (MACT)
d'essai des barres corroyees en cuivre et alliages de en alliages d'aluminium. Generalites.
cuivre pour constructions aerospatiales. Statut :Homologuee
Statut :Homologuee NF L 19-010 Decembre 1995 : Serie aerospatiale.
A 11-100 AoOt 1983 : Analyse chimique du ferro-niobium. Materiaux alveolaires a cellules tubulaires (MACT)
Dosages du silicium, tantale, titane, niobium, etain, hexagonales en alliage d'aluminium 3003. Norme de
aluminium et fer apres separation sur resines produit. Statut :Homologuee
echangeuses d'ions Statut :Fascicule de doc. NF L 19-011 Decembre 1995 : Serie aerospatiale.
J 13-005 Janvier 1968 : Aluminium et alliages d'aluminium. Materiaux alveolaires a cellules tubulaires (MACT)
Produits lamines et files - Liste des alliages utilisables. hexagon ales en alliage d'aluminium 5052. Norme de
Statut :Fascicule de doc. produit. Statut :Homologuee
NF L 15-113 Septembre 1972 : Toles en alliages NF L 19-013 Decembre 1995 : Serie aerospatiale.
d'aluminium tolerancees sur I'ensemble de la surface. Materiaux alveolaires a cellules tubulaires (MACT)
Statut :Homologuee hexagon ales en alliage d'aluminium 5056. Norme de
produit. Statut :Homologuee
NFL 15-115 AoOt 1973 : Toles en alliages d'aluminium.
Statut :Homologuee NF L 19-014 Decembre 1995 : Serie aerospatiale.
Materiaux alveolaires a cellules tubulaires (M.A.G.T.)
NF L 15-152 Juillet 1978 : Bandes en aluminium et alliages hexagonales en alliage d'aluminium 2024. Norme de
d'aluminium. Statut :Homologuee produit. Statut Homologuee
NF L 15-312 Septembre 1972 : Barres rondes etirees en NF L 19-101-1 Fevrier 1992: Aeronautique et espace.
alliages d'aluminium. Statut :Homologuee Materiaux alveolaires a cellules tubulaires (MAC.T) en
NF L 15-314 Septembre 1972: Barres rondes filees en alliages d'aluminium. Specification technique -
alliages d'aluminium. Statut :Homologuee Exigences generales. Statut :Homologuee
NF L 15-322 Septembre 1972 : Barres hexagonales etirees NF L 19-101-2 Fevrier 1992 : Aeronautique et espace.
en alliages d'aluminium. Dimensions et tolerances. Materiaux alveolaires a cellules tubulaires (MAC.T) en
Statut :Homologuee alliages d'aluminium. Specification technique -
NF L 15-332 Septembre 1972 : Barres carrees, filees et Exigences particulieres aux cellules tubulaires
etirees, en alliages d'aluminium. Statut :Homologuee hexagonales. Statut :Homologuee
NF L 15-340 Septembre 1972 : Meplats files en alliages NF F 19-303 Septembre 1996 : Materiel roulant ferroviaire.
d'aluminium. Statut :Homologuee Peinture monocouche hydrodiluable pour aluminium et
ses alliages. Statut :Homologuee
NF L 15-501 Decembre 1968 : Profiles files en alliages
d'aluminium. Tolerances generales NF L 21-106 Janvier 1975: Fils a rivets en alliages
Statut :Homologuee d'aluminium, en acier, en alliages inoxydables et
refractaires - Dimensions. Statut :Homologuee
NF L 15-512 Avril 1973 : Cornieres a ailes egales et
inegales filees en alliages d'aluminium. NF L 21-201 Juillet 1972 : Rivets en alliages d'aluminium-
Statut :Homologuee Norme de produit. Statut :Homologuee
NF L 15-520 Avril 1973 : Cornieres a boudin filees en NFL 21-211 Mars 1980 : Rivets a tete goutte de suif en
alliages d'aluminium. Statut :Homologuee alliages d'aluminium. Statut :Homologuee
NF L 15-530 Avril 1973 : Profiles en U files en alliages NFL 21-212 Mars 1980 : Rivets a tete cylindrique plate en
d'aluminium. Statut :Homologuee alliages d'aluminium. Statut :Homologuee
NF L 15-540 Avril 1973 : Profiles en T files en alliages NF L 21-213 Mars 1980 : Rivets a tete fraisee 120 degres
d'aluminium. Statut :Homologuee en alliages d'aluminium .. Statut :Homologuee
NF L 15-560 AoOt 1973 : Profiles plies en omega en alliages NF L 21-214 Mars 1980 : Rivets a tete fraisee 120 degres
d'aluminium. Statut :Homologuee bombee en alliages d'aluminium .. Statut :Homologuee
NF L 15-570 AoOt 1973 : Profiles plies en zede en alliages NF L 21-216 Mars 1980 : Rivets a tete fraisee 90 degres en
d'aluminium. Statut :Homologuee alliages d'aluminium .. StatutHomologuee
NF L 15-611 Avril 1973 : Tubes circulaires etires en alliages NF L 21-271 Septembre 1981 : Rivets composites "SL" a
d'aluminium. Tolerances courantes. tige en alliage de titane T-A6V a tete cylindrique et a
Statut :Homologuee bague en alliage 2024. Statut :Homologuee
NF L 15-612 Avril 1973 : Tubes circulaires etires en alliages NF L 21-272 Septembre 1981 : Rivets composites "SL" a
d'aluminium. Tubes de precision. Statut :Homologuee tige en alliage de titane T -A6V a tete fraisee 100
degres et a bague en alliage d'aluminium 2024 ..
NF L 15-640 Septembre 1973 : Tubes carres etires en
Statut :Homologuee
alliages d'aluminium. Statut :Homologuee
P 22-202-1/2 Mai 1993 DTU 32.2. : Travaux de batiment.
NF L 15-641 Septembre 1973 : Tubes rectangulaires etires
Construction metallique. Charpente en alliages
en alliages d'aluminium. Statut :Homologuee
d'aluminium .. Reference commerciale des parties 1/2
NF L 15-660 Mai 1978 : Tubes profiles torpedo en alliages (changement de statut du DTU 32.2) Statut :Extrait de
d'aluminium. Statut :Homologuee norme (condense)
NF L 16-001 Mai 1991 : Industrie aeronautique. Peintures et NF P 22-202-1 Mai 1993: Travaux De 8atiment-
vernis. Nature et methodes de preparation de surface Construction Metallique - Charpentes En Alliages
des eprouvettes en alliages d'aluminium. D'aluminium - Partie 1 : Cahier Des Clauses
Statut :Homologuee Techniques. (Changement De Statut Du DTU 32.2
D'avril 1967). Vendue Uniquement Avec La Partie 2.
Statut :Homologuee
378 Appendix A - Standards
AFNOR NF Standards (Aluminium) - continued. C 34-200 Octobre 1993 Conducteurs nus pour lignes
NF P 22-202-2 Mai 1993 Travaux De Batiment - Marches aeriennes. Caracteristiques des produits de protection
Prives - Construction Metallique - Charpente En pour conducteurs nus en aluminium, en alliage
Alliages D'aluminium - Partie 2 Cahier Des Clauses d'aluminium ou en acier pour lignes aeriennes.
Speciales. (Changement De Statut Du DTU 32.2 D'avril Statut .Experimentale
1967). Vendue Uniquement Avec La Partie 1. Projet C 34-200 Novembre 1995 Caracteristiques Des
Statut .Homologuee Produits De Protection Pour Conducteurs Nus En
NF E 22-555 Decembre 1985 Paliers lisses. Alliage Aluminium, En Alliage D'aluminium Ou En Acier Pour
d'aluminium pour paliers massifs. Statut .Homologuee Lignes Aeriennes Projet
NF P 24-301 AoOt 1980 Specifications techniques des P 34-206-1/2 Mai 1993 DTU 40.36 . Travaux de batiment.
fenetres, portes-fenetres et chassis fixes metalliques Couverture en plaques nervurees d'aluminium
Statut .Homologuee prelaque ou non .. Reference commerciale des parties
1/2 (changement de statut du DTU 40.36)
NF L 25-110 Juillet 1979 Charnieres en alliage
Statut Extrait de norme (condense)
d'aluminium. Statut .Homologuee
NF P 34-411 Mars 1983 Couverture. Plaques ondulees ou
NF E 25-703 Decembre 1988 Elements de fixation. Rivets
nervurees en alliage d'aluminium. Statut .Homologuee
aveugles 8 rupture de tige dits "etanches".
Caracteristiques - Methodes d'essai. (2e tirage NF P 34-504 Juin 1983 Couverture. Plaques nervurees en
corrige). Statut .Homologuee alliage d'aluminium - Essais de flexion statique et
dynamique Statut .Homologuee
NF P 26-309 Fevrier 1958 Articles de quincaillerie moules
par gravite en alliages d'aluminium dits de premiere NF P 34-631 Mai 1983 Couverture - Fa90nnes lineaires en
fusion. Statut .Homologuee aluminium ou alliage d'aluminium Statut .Homologuee
NF E 29-741 Octobre 1991 Recipients 8 gaz. Bouteilles 8 Projet T 34-750-1 Fevrier 1996 Peintures Et Vernis
gaz en aluminium non allie ou en alliages d'aluminium, Revetements De L'aluminium Pour Applications
sans soudure. Construction - Essais. Architecturales Partie 1 Revetements A Partir De
Statut .Homologuee Peintures En Poudre Projet
E 29-742 Septembre 1992 Bouteilles 8 gaz. Corps NF H 35-089 Septembre 1993. Industries de
d'extincteurs "haute pression" sans soudure en I'embouteillage. Futs 8 biere cylindriques en alii age
aluminium non allie et en alliages d'aluminium. d'aluminium. Caracteristiques. Statut Homologuee
Construction - Essais. Statut Experimentale NF L 35-111 Juillet 1978 Corps de bielle en alliage
Projet E 29-743 Septembre 1995 Bouteilles A Gaz d'aluminium pour commandes de vol - Specification
Transportables Specifications Pour La Conception Et technique (completee par Ie modificatif 1, aout 1979).
La Fabrication De Bouteilles A Gaz Rechargeables Et Statut .Homologuee
Transportables En Alliage D'aluminium Sans Soudure NF L 35-112 Septembre 1976 Corps de bielles en alliage
De Capacite Comprise Entre 0, 5 Litre Et 150 Litres d'aluminium pour commandes de vol et structures
Inclus Projet d'aeronefs - Dimensions Statut .Homologuee
NF E 29-752 Decembre 1991 Recipients 8 gaz. Bouteilles NF H 44-006 Decembre 1988 Generateurs d'aerosols.
frettees avec corps en alliage d'aluminium sans Recipients en aluminium et alliages d'aluminium.
soudure. Constructions - Essais. Statut .Homologuee Tolerances des dimensions de base en rapport avec Ie
Projet E 29-752 Mars 1996 Bouteilles A Gaz dudgeonnage. Statut Homologuee
Transportables Bouteilles Sans Soudure, Frettees En Projet A 50-001 Avril 1996 Aluminium Et Alliages
Materiau Composite Specifications Projet D'aluminium Termes Et Definitions Projet
NF E 29-762 Juillet 1990 Recipients 8 gaz. Bouteilles 8 NF A 50-101 Avril 1990 Aluminium et alliages d'aluminium.
gaz sans soudure en alliages d'aluminium. Essais de Alliages d'aluminium pour recipients 8 gaz, sans
corrosion. Statut .Homologuee soudure. Nuances - Demi-produits billettes.
NF C 31-520 Aout 1979 Barres meplates en aluminium et Statut .Homologuee
alliages d'aluminium pour tableaux et canalisations Projet A 50-120 Aout 1996. Aluminium Et Alliages
electriques (8 angles arrondis). Statut .Homologuee D'aluminium Produits Corroyes Exigences Particulieres
UTE C 32-015 Juin 1985 Ames des conducteurs et cables Pour Les Produits Destines A La Fabrication Des
isoles en alliage d'aluminium revetu d'une couche de Appareils A Pression Projet
nickel - Guide precisant les caracteristiques des ames NF A 50-181 Novembre 1970 Aluminium et alliages
et les essais de verification correspondants (document d'aluminium. Bandes minces et feuilles - Essais
provisoire). (complete par un rectificatif). Statut Doc. mecaniques - Traction - Emboutissage - Eclatement
de reference Statut .Enregistree
C 34-112 Octobre 1992 Fils en alliage d'aluminium - NF A 50-261 Janvier 1977 Aluminium et alliages
Magnesium - Silicium pour conducteurs de !ignes d'aluminium. Bandes minces et feuilles - Essais
aeriennes. Statut .Experimentale physiques - Porosite - Mouillabilite - Epaisseur -
Projet C 34-112 Juillet 1994 Fil En Alliage D'aluminium- Adherence entre spires Statut .Enregistree
Magnesium-Silicium Pour Conducteurs De Lignes NF A 50-301 Decembre 1991 Aluminium et alliages
Aeriennes Projet d'aluminium - Mesure des indices de comes 8
C 34-125 Octobre 1992 Conducteurs nus en alliages I'emboutissage. Statut .Homologuee
d'aluminium et en alliage d'aluminium-acier pour lignes NF A 50-401 Decembre 1988. Aluminium et alliages
aeriennes. Statut .Experimentale d'aluminium. Fils machine obtenus par coulee et
laminage en continuo Caracteristiques generales.
Statut .Homologuee
Appendix A - Standards 379
AFNOR NF Standards (Aluminium) - continued. NF A 50-705 Juiliet 1984: Aluminium et alliages
NF A 50-402 Decembre 1988 : Aluminium et alliages d'aluminium. Meplats files - Tolerances sur dimensions
d'aluminium. Fils machine pour conducteurs et dimensions recommandees Statut :Homologuee
electriques. Caracteristiques. Statut :Homologuee NF A 50-706 AoOt 1987 : Aluminium et alliages d'aluminium
NF A 50-403 Juillet 1989: Aluminium et alliages Cornieres - Tolerances de forme et dimensions
d'aluminium. Fils machines pour soudLlre. Statut :Homologuee
Caracteristiques. Statut :Homologuee NF A 50-707 Decembre 1981 : Aluminium et alliages
NF A 50-404 Juiliet 1989: Aluminium et alliages d'aluminium. Profiles de section simple files en forme I
d'aluminium. Fils machines a usages mecaniques (hors - Tolerances sur dimensions et dimensions
soudure). Caracteristiques. Statut :Homologuee recommandees Statut :Enregistree
Projet A 50-434-1 Janvier 1997 : Aluminium Et Alliages NF A 50-708 Mars 1982 : Aluminium et alliages
D'aluminium Ebauches De Relaminage Pour d'aluminium. Profiles de section simple files en forme T
Applications Generales - Partie 1 : Specifications Pour - Tolerances sur dimensions et dimensions
Ebauches Obtenues Par Laminage A Chaud Projet recommandees Statut :Enregistree
Projet A 50-443 Avril 1995 : Aluminium Et ,A,lIiages NF A 50-709 Decembre 1981 : Aluminium et alliages
D'aluminium Feuille Mince Partie 4 : Proprietes d'aluminium. Profiles de section simple files en forme U
Particulieres Projet - Tolerances sur dimensions et dimensions
recommandees Statut :Enregistree
NF A 50-452 Septembre 1984 : Aluminium et aliiages
d'aluminium. Produits prelaques livres en toles ou en NF A 50-710 Fevrier 1981 : Aluminium et alliages
bandes - Caracteristiques Statut :Homologuee d'aluminium. Profiles de section quelconque files -
Tolerances sur dimensions Statut :Enregistree
NF A 50-501 Septembre 1987 : Aluminium et alliages
d'aluminium. Tubes sou des - Prescriptions generales. NF A 50-711 Septembre 1986 : Aluminium et alliages
Statut :Homologuee d'aluminium. Tubes de section circulaire files livres en
longueurs droites pour usages generaux - Tolerances
NF A 50-506 Mars 1982 : Aluminium et alliages de forme et dimensions (2e tirage, fevrier 1987,
d'aluminium. Profils obtenus a froid sur machines a erratum incorpore). Statut :Homologuee
galet et sur presses plieuses - CaractE,ristiques
generales Statut :Enregistree NF A 50-712 Decembre 1986 : Aluminium et alliages
d'aluminium. Tubes de section circulaire files livres en
Projet A 50-616 Decembre 1995: Aluminium Et Alliages couronne pour usages generaux - Tolerances de forme
D'aluminium Barres Et Tubes Etires Partie 7 : Tubes et dimensions. Statut :Homologuee
Files Sur Aiguille, Tolerances Sur Dimensions Et
Forme Projet NF A 50-735 Decembre 1986: Aluminium et alliages
d'aluminium. Fils meplats etires livres en couronne -
Projet A 50-640-1 Decembre 1995 : Aluminium Et Alliages Tolerances de forme et dimensions.
D'aluminium Profiles De Precision Files En Alliages En Statut :Homologuee
Aw-6060 Et En Aw-6063 Partie 1 : COl1ditions
Techniques De Controle Et De Livraison Projet NF A 50-736 Juillet 1970: Aluminium et alliages
d'aluminium. Fils trefiles livres en couronne -
Projet A 50-650-1 Mars 1995 : Aluminium Et Alliages Tolerances sur dimensions et dimensions
D'aluminium Fil Machine Partie 1 : Exigences recommandees Statut :Enregistree
Generales Et Conditions Techniques De Controle Et
De Livraison Projet NF A 50-737 Juillet 1970: Aluminium et alliages
d'aluminium. Tubes de section circulaire etires livres en
Projet A 50-670 Juin 1994 : Aluminium Et .I'Iliiages longueurs droites ou en couronnes - Tolerances sur
D'aluminium Fil Etire Partie 1 : Conditions Techniques dimensions et dimensions recommandees
De Controle Et De Livraison Projet Statut :Enregistree
Projet A 50-671 AoOt 1995 : Aluminium Et Alliages NF A 50-738 Fevrier 1987 : Aluminium et alliages
D'aluminium Fil Etire Partie 2 : Caracteristiques d'aluminium. Tubes de section carree et rectangulaire
Mecaniques Projet etires - Tolerances de forme et dimensions.
Projet A 50-672 Juin 1994 : Aluminium Et Miages Statut :Homologuee
D'aluminium Fil Etire Partie 3 : Tolerances Sur NF A 50-751 Juin 1970 : Aluminium et alliages d'aluminium.
Dimensions Projet Toles - Tolerances sur dimensions Statut :Enregistree
NF A 50-701 Juillet 1982 : Aluminium et alliages NF A 50-761 Juin 1970 : Aluminium et alliages d'aluminium.
d'aluminium. Produits files et files etirEls - Repartition Bandes roulees - Tolerances sur dimensions
en groupes selon composition Statut :Enregistree Statut :Enregistree
NF A 50-702 Juillet 1984 : Aluminium et aliiages NF A 50-801 Septembre 1987 : Aluminium et alliages
d'aluminium. Barres de section circulaire filees - d'aluminium. Tubes soudes de section circulaire -
Tolerances sur dimensions et dimensions Tolerances de forme et dimensions
recommandees Statut :Homologuee Statut :Homologuee
NF A 50-703 Juiliet 1984 : Aluminium et alliages NF A 50-802 Mai 1988: Aluminium et alliages d'aluminium.
d'aluminium. Barres de section carree filees - Tubes soudes de gros diametres. Dimensions et
Tolerances sur dimensions et dimensions tolerances. Statut :Homologuee
recommandees Statut :Homologuee
NF A 50-805 Septembre 1987 : Aluminium et alliages
NF A 50-704 Juillet 1984: Aluminium et alliages d'aluminium. Tubes soudes de section carree ou
d'aluminium. Barres de section hexagonale filees - rectangulaire - Tubes soudes de forme - Tolerances de
Tolerances sur dimensions et dimensions forme et dimensions. Statut :Homologuee
recommandees Statut :Homologuee
380 Appendix A - Standards
AFNOR NF Standards (Aluminium) - continued. NF F 80-153 Decembre 1986 : Rayons de pliage a froid des
Projet A 50-810 Decembre 1994: Aluminium Et Alliages produits plats. Rayons minimaux de pliage des produits
D'aluminium Tubes Electro-Soudes Hf Partie 1: prelaques en aluminium et alliages d'aluminium livres
Conditions Techniques De Controle Et De Livraison en tales ou en bandes. Statut :Homologuee
Projet NF F 80-200 AoOt 1988 : Materiel roulant ferroviaire. Tubes
NF A 50-821 Fevrier 1971 : Aluminium et alliages pour canalisations de flu ides. Matieres et dimensions -
d'aluminium. Profils de formes obtenus a froid sur Selection. Statut :Homologuee
machines a galets - Dimensions et tolerances sur NF A 81-331 Mai 1984: Aluminium et alliages d'aluminium-
dimensions Statut Enregistree Soudage - Brasage fort et soudobrasage - Produits
NF A 50-825 Fevrier 1971 : Aluminium et alliages d'apport - Symbolisation - Specifications
d'aluminium. Profils obtenus a froid par pliage a la Statut :Homologuee
presse - Tolerances sur dimensions Statut :Enregistree NF A 81-410 Mai 1984 : Aluminium et alliages d'aluminium-
Projet A 50-922 Mai 1996 : Aluminium Et Aliiages Soudage - Brasage fort et soudobrasage - Produits de
D'aluminium Produits Corroyes Destines A La Forge base et choix des produits d'apport
Partie 3 : Tolerances Sur Dimensions Et Forme Projet Statut :Homologuee
Projet A 50-930 Fevrier 1992 : Pieces Forgees En NF A 81-900 Mars 1973 : Aluminium et alliages d'aluminium
Aluminium Et Alliages D'aluminium Corroyes Partie 1 : - Soudage - Emploi et contrale des flux decapants
Conditions Techniques De Controle Et De Livraison Statut :Enregistree
Projet NF F 82-001 Aout 1990 : Materiel roulant ferroviaire.
Projet A 50-932 Decembre 1996 : Aluminium Et Alliages Produits files soudables en alliage d'aluminium pour
D'aluminium Pieces Forgees Partie 3 : Tolerances Sur ossature de caisse. Statut :Homologuee
Dimensions Et Forme Projet NF E 82-102 Decembre 1982 : Pieces forgees par
NF L 52-150 Octobre 1986: Materiels aeronautiques- matric;:age en aluminium et aliiages d'aluminium.
Cables electriques a conducteur en alliage d'aluminium Tolerances dimensionnelies Statut :Enregistree
- Caracteristiques Statu! :Homologuee NF E 82-110 Decembre 1982 : Pieces forgees par
NF F 55-310 Decembre 1993 : Installations fixes matric;:age en aluminium et alliages d'aluminium.
ferroviaires. Potences et portiques de signalisation en Conditions techniques generales de fourniture
alliage d'aluminium. StatutHomologuee Statut :Fascicule de doc.
NF A 57-105 (Jan. 1988) : Aluminium and Aluminium Alloys NF A 87-010 Avril 1973 : Aluminium et alliages d'aluminium
- Foundry Products. - Soudage - Preparation des bords Statut :Fascicule de
doc.
NF A 57-702 Fevrier 1981 : Produits de fonderie.
Caracteristiques des pieces moulees par gravite, M 88-109 Novembre 1994 : Citernes destinees au transport
basse pression et depression en aluminium ou en de matieres dangereuses. Regles de fabrication des
alliages d'aluminium Statu! :Enregistree citernes en aliiage d'aluminium. Statut :Experimentale
NF A 57-703 Juillet 1984 : Produits de fonderie. Pieces NF A 89-220 Avril 1973 : Aluminium et alliages d'aluminium
moulees sous pression en aluminium et en aliiages - Soudage. Classification et contrale des jOints sou des
d'aluminium - Caracteristiques Statut :Homologuee Statut :Enregistree
NF A 57-711 Juillet 1984 : Produits de fonderie. Pieces Projet A 89-234 Fevrier 1996 : Soudage Assemblages En
moulees sous pression en aluminium, aliiages Aluminium Et Alliages D'aluminium Soudables Soudes
d'aluminium, de magnesium et de zinc - Conditions de Par Faisceau D'electrons Et Par Faisceau Laser Guide
fourniture Statut :Homologuee Des Niveaux De Qualite Des Defauts Projet
NF C 63-061 Decembre 1973 : Raccords de connexion pour NF A 89-310 Avril 1973 : Aluminium et alliages d'aluminium
conducteurs dont I'un au moins est isole et en - Soudage - Assemblages elementaires types -
aluminium ou en alliage d'aluminium - Regles d'essais Criteres de choix Statut :Fascicule de doc.
electriques Statut :Enregistree Projet A 89-500 Novembre 1995 : Contrale Non Destructif
NF C 64-450 + AMDT 2 Novembre 1993 : Enveloppes en Des Assemblages Soudes Regles Generales Projet
alliage d'aluminium coule pour I'appareillage a haute Projet A 89-510 Juillet 1994 : Controle Non Destructif Des
tension so us pression de gaz. Statut :Homologuee Assemblages Soudes Examen Radiographique Des
A 65-700 Decembre 1982 : Le magnesium et ses alliages - Assemblages Soudes Par Fusion Projet
Caracteristiques - Mise en oeuvre - Applications NF A 89-562 Fevrier 1987 : Examen aux rayons X des joints
Statut :Fascicule de doc. bout a bout et des piquages soudes par fusion sur
NF A 66-002 Septembre 1985 : Produits de fonderie. aluminium et ses alliages d'epaisseur comprise entre 5
Alliages d'aluminium et alliages de zinc - Tolerances mm et 50 mm - Pratiques recommandees.
dimensionnelles des pieces moulees sous pression. Statut :Homologuee
Statut :Homologuee NF S 90-539 Janvier 1975 : Pieces constitutives des
NF P 78-456 Avril 1986 : Vitrages isolants. Methode de protheses et des ortheses. Articulation malieolaire pour
determination de I'indice de penetration de I'humidite prothese du membre inferieur en alliage leger ou en
Statut :Homologuee matiere plastique. Statut :Homologuee
NF F 80-152 Juillet 1981 : Rayons de pliage a froid des NF A 91-400 Juillet 1987 : Anodisation de I'aluminium et de
produits plats. Rayons minimaux de pliage des produits ses aliiages - Vocabulaire. Statu! :Homologuee
et demi-produits lamines en metaux non ferreux. NF A 91-401 Octobre 1966 : Traitements de surface des
Statut Enregistree metaux - Anodisation (oxydation anodique) de
I'aluminium et de ses alliages. Nomenclature des
methodes d'essais Statut :Homologuee
Appendix A - Standards 381
AFNOR NF Standards (Aluminium) - continued. NF A 91-416 Juin 1982 Traitement de surface des metaux
NF A 91-402 Octobre 1981 Traitements de surface des - Anodisation (oxydation anodique) de I'aluminium et
metaux - Anodisation (oxydation anodique) de de ses alliages. Evaluation de la qualite des couches
I'aluminium et de ses alliages. Mesure de I'epaisseur - anodiques colmatees par mesurage de la perte de
Coupe micrographique. Statut Enregistree masse apres immersion en solution phosphochromique
Statut .Enregistree
NF A 91-403 Juillet 1985 Aluminium et alliages
d'aluminium anodises - Mesurage de I'epaisseur - A 91-424 Fevrier 1988 Traitements de surface. Aluminium
a
Mesurage non destructif par microscope coupe et alliages d'aluminium anodises. Determination de la
couleur et de la difference de couleur des couches
optique. Statut .Homologuee
anodiques colorees. Statut .Fascicule de doc.
NF A 91-404 Octobre 1966 Traitements de surface des
metaux - Anodisation (oxydation anodique) de NF A 91-450 Decembre 1981 Traitements de surface des
I'aluminium et de ses alliages - Mesure de I'epaisseur - metaux - Anodisation (oxydation anodique) de
Mesures electriques (courant de Foucault) I'aluminium et de ses alliages. Couches anodiques sur
Statut Homologuee aluminium - Specifications generales
Statut Enregistree
NF A 91-405 Mars 1983 Traitement de surface des metaux
- Anodisation de I'aluminium et de ses alliages - A 91-451 Septembre 1988 Traitements de surface.
Contrale de I'isolement electrique par mesurage de la Aluminium et alliages d'aluminium anodises.
tension de claquage Statut .Enregistree Qualification des produits d'entretien.
Statut .Experimentale
NF A 91-406 Juillet 1985 Aluminium et alliages
d'aluminium anodises - Mesurage de la masse par Projet A 91-45521 Avril 1997 Aluminium Et Alliages
unite de surface - Methode gravimetrique. D'aluminium Anodisation Partie 21 Methode De
Statut .Homologuee Specification Des Caracteristiques Des Revetements
Decoratifs Et Protecteurs Obtenus Par Oxydation
NF A 91-407 Octobre 1981 Traitements de surface des Anodique Sur Aluminium Projet
metaux - Anodisation (oxydation anodique) de
I'aluminium et de ses alliages - Contrale de colmatage Projet A 91-475 Novembre 1996 Couches De Conversion
par mesurage de la perte de masse apres immersion Phosphatees Des Metaux Methode De Specifications
en solution acide Statut .Enregistree Des Exigences Projet
NF A 91-408 Juillet 1985. Aluminium et alliages NF A 92-020 Septembre 1990 Emaux vitrifies deposes sur
d'aluminium anodises - Contrale du colmatage - Essai I'aluminium et ses alliages. Fabrication des echantillons
a la goutte de bleu sanodal G Statut .Homologuee pour essai. Statut .Homologuee
NF A 91-409 Juin 1987 Anodisation de I'aluminium et de NF A 92-021 Septembre 1990 Emaux vitrifies deposes sur
ses alliages - Appreciation de la perte du pouvoir I'aluminium et ses alliages. Essais d'adherence.
absorbant des couches d'oxydes anodiques apres Statut .Homologuee
colmatage - Essai a la goutte de colorant avec action NF P 93-330 Decembre 1995 Equipement de chantier.
acide prealable. Statut .Homologuee Bennes a beton metalliques pour chantiers de batiment
NF A 91-410 Octobre 1966 Traitements de surface des et travaux publics. Exigences - Essais.
metaux - Anodisation (oxydation anodique) de Statut .Homologuee
I'aluminium et de ses alliages. Contrale de la continuite NF P 93-340 Juin 1994 Equipement de chantier. Garde-
- Essai au sulfate de cuivre Statut .Homologuee corps metallique provisoire de chantier (GCMPC).
NF A 91-411 Octobre 1966 Traitements de surface des Statut .Homologuee
metaux - Anodisation (oxydation anodique) de NF P 93-352 Decembre 1993 Equipement de chantier.
I'aluminium et de ses alliages. Contrale de la Plate-forme individuelle roulante. Statut .Homologuee
resistance a la corrosion - Essais d'immersions - NF P 93-353 Decembre 1994 Equipement de chantier.
Emersions alternees en solution saline Plate-forme individuelle roulante legere.
Statut Homologuee Statut .Homologuee
NF A 91-412 AoOt 1982 Traitement de surface des metaux NF P 93-501 Decembre 1988 Equipements de chantier.
- Anodisation de I'aluminium et de ses alliages. Essai Echafaudages de service a elements prefabriques.
accelere de resistance a la lumiere artificielle des Methodes d'essais. Statut .Homologuee
couches anodiques colorees Statut .Enregistree
XP S 94-081-1 Mars 1996 Implants chirurgicaux. Alliage a
NF A 91-413 Septembre 1981 Traitement de surface des base de titane, d'aluminium 6 et de niobium 7. Partie 1
fTletaux - Anodisation de I'aluminium et de ses alliages. barres et billettes. Statut .Experimentale
Evaluation de la resistance des couches anodiques a
XP S 94-081-2 Mars 1996 Implants chirurgicaux. Alliage a
la formation de criques par deformation
base de titane, d'aluminium 6 et de niobium 7. Partie 2
Statut Enregistree
produits semi-finis obtenus par forgeage ou par
NF A 91-414 Septembre 1981 Traitements de surface des usinage. StatutExperimentale
metaux - Anodisation (oxydation anodique) de
NF P 97-402 Novembre 1982 Candelabres d'eclairage
I'aluminium et de ses alliages. Contrale du colmatage -
public. Materiaux. Statut .Enregistree
Mesurage de I'admittance ou de I'impedance
Statut .Enregistree NF P 97-403 Novembre 1982. Candelabres d'eclairage
public. Protection de surface des candelabres
NF A 91-415 Septembre 1981 Traitements de surface des
d'eclairage public metalliques. Statut .Enregistree
metaux - Anodisation (oxydation anodique) de
I'aluminium et de ses alliages. Determination de la P 98-422 AoOt 1994 Barrieres de securite rou!ieres.
solidite a la lumiere ultraviolette des couches Barrieres de securite en beton arme et en metal BN1 et
anodiques colorees Statut .Enregistree BN2. Composition, fonctionnement, performances de
retenue, conditions d'implantation et de montage,
elements constitutifs. Statut .Experimentale
382 Appendix A - Standards
NF EN Standards NF EN 573-3 Oc1obre 1994 : Aluminium et alliages
d'aluminium. Composition chimique et forme des
NF EN 286-4 Oecembre 1994 : Recipients a pression produits corroyes. Partie 3 : composition chimique.
simples, non soumis a la flam me, destines a contenir Statut :Homologuee
de I'air ou de I'azote. Partie 4 : recipients a pression en
alliages d'aluminium destines aux equipements NF EN 573-4 Octobre 1994 : Aluminium et alliages
pneumatiques de freinage et aux equipements . d'aluminium. Composition chimique et forme des
pneumatiques auxiliaires du ma Statut :Homologuee produits corroyes. Partie 4 : forme des produits.
Statut :Homologuee
NF EN 287-2 Juin 1992 : Epreuve de qualification des
soudeurs. Soudage par fusion. Partie 2 : aluminium et NF EN 575 Septembre 1995 : Aluminium et alliages
ses alliages. Statut :Homologuee d'aluminium. Alliages meres obtenus par fusion.
Specifications. Statut :Homologuee
NF EN 288-4 Mai 1993 : Oescriptif et qualification d'un
mode operatoire de soudage pour les materiaux NF EN 576 Septembre 1995 : Aluminium et alliages
metalliques. Partie 4 : epreuve de qualification d'un d'aluminium. Lingots pour refusion en aluminium non
mode operatoire de soudage a I'arc sur I'aluminium et allie. Specifications. Statut :Homologuee
ses alliages. Statut :Homologuee NF EN 577 Septembre 1995 : Aluminium et alliages
NF EN 485-1 Juin 1994 : Aluminium et alii ages d'aluminium. d'aluminium. Metalliquide. Specifications.
Tales, bandes et t6les epaisses. Partie 1 : conditions Statut :Homologuee
techniques de contrale et de livraison. NF EN 586-2 AoOt 1994 : Aluminium et alliages
Statut :Homologuee d'aluminium. Pieces forgees. Partie 2 : caracteristiques
NF EN 485-2 Oecembre 1994 : Aluminium et alliages mecaniques et autres caracteristiques exigees.
d'aluminium. Tales, bandes et t6les epaisses. Partie 2 : Statut :Homologuee
caracteristiques mecaniques. Statut :Homologuee NF EN 601 Oecembre 1994: Aluminium et alliages
NF EN 485-3 Juin 1994 : Aluminium et alliages d'aluminium. d'aluminium. Pieces moulees. Composition chimique
Tales, ban des et tales epaisses. Partie 3 : tolerances des pieces moulees destinees a entrer en contact avec
sur forme et dimensions des produits lamines a chaud. les aliments. Statut :Homologuee
Statut :Homologuee NF EN 602 Oecembre 1994 : Aluminium et alliages
NF EN 485-4 Juin 1994 : Aluminium et alliages d'aluminium. d'aluminium. Produits corroyes. Composition chimique
Tales, bandes et tales epaisses. Partie 4 : tolerances des demi-produits utilises pour la fabrication d'articles
sur forme et dimensions des produits lamines a froid. destines a entrer en contact avec les aliments.
Statut :Homologuee Statut :Homologuee
NF EN 486 Mars 1994 : Aluminium et alliages d'aluminium. NF EN 603-1 Oecembre 1996 : Aluminium et alliages
Billettes de filage. Specifications. Statut :Homologuee d'aluminium. Produits corroyes destines a la forge.
Partie 1 : conditions techniques de contrale et de
NF EN 487 Mars 1994 : Aluminium et alliages d'aluminium. livraison. Statut :Homologuee
Plaques de laminage. Specifications.
Statut :Homologuee NF EN 603-2 Oecembre 1996 : Aluminium et alliages
d'aluminium. Produits corroyes destines a la forge.
NF EN 515 Octobre 1993 : Aluminium et alliages Partie 2 : caracteristiques mecaniques.
d'aluminium. Produits corroyes. Oesignation des etats
metallurgiques. Statut :Homologuee NF EN 604-1 Mai 1997: Aluminium et alliages d'aluminium-
produits coules et destines a la forge - Partie 1 :
NF EN 541 Avril 1995 : Aluminium et alliages d'aluminium. conditions techniques de controle et de livralson.
Produits lamines pour boites, capsules rigides et Statut :Homologuee
couvercles. Specifications. Statut Homologuee
NF EN 604-2 Mai 1997 : Aluminium et alliages d'aluminium -
NF EN 546-1 Oecembre 1996 : Aluminium et alliages produits coules et destines a la forge - Partie 2 :
d'aluminium. Feuille mince. Partie 1 : conditions tolerances sur dimensions et forme.
techniques de contrale et de livraison.
NF EN 683-1 Janvier 1997: Aluminium et alliages
Statut Homologuee
d'aluminium. Bandes pour echangeurs thermiques.
NF EN 546-2 Oecembre 1996 : Aluminium et alliages Partie 1 : conditions techniques de contrale et de
d'aluminium. Feuille mince. Partie 2 : caracteristiques livraison. Statut :Homologuee
mecaniques. Statut :Homologuee
NF EN 683-2 Novembre 1996 : Aluminium et alliages
NF EN 546-3 Oecembre 1996 : Aluminium et alliages d'aluminium. Bandes pour echangeurs thermiques.
d'aluminium. Feuille mince. Partie 3 : tolerances sur Partie 2 : caracteristiques mecaniques.
dimensions. Statut :Homologuee Statut :Homologuee
NF EN 570 Octobre 1994 : Aluminium et alliages
NF EN 683-3 Novembre 1996 : Aluminium et alliages
d'aluminium. Pions de filage par choc obtenus a partir d'aluminium. Bandes pour echangeurs thermiques.
de produits corroyes. Specifications.
Partie 3 : tolerances sur dimensions et forme.
Statut :Homologuee
Statut :Homologuee
NF EN 573-1 Octobre 1994 : Aluminium et alliages
NF EN 754-1 Juin 1997 : Aluminium Et Alliages O'aluminium
d'aluminium. Composition chimique et forme des
- Barres Et Tubes Etires - Partie 1 : Conditions
produits corroyes. Partie 1 : systeme de designation
Techniques Oe Controle Et Oe Livraison. (Remplace
numerique. Statut :Homologuee
En Partie NF A 01-101, Novembre 1972)
NF EN 573-2 Octobre 1994: Aluminium et alliages Statut :Homologuee
d'aluminium. Composition chimique et forme des
NF EN 754-2 Juin 1997 : Aluminium Et Alliages O'aluminium
produits corroyes. Partie 2 : systeme de designation.
- Barres Et Tubes Etires - Partie 2 : Caracteristiques
fonde sur les symboles chimiques. Statut :Homologuee
Mecaniques. (Rem place En Partie NF A 50-411, Avril
1989) Statut :Homologuee
Appendix A - Standards 383
AFNOR NF EN Standards (Aluminium) - continued. NF EN 1780-1 Decembre 1996: Aluminium et alliages
NF EN 754-3 Decembre 1995 : Aluminium et alliages d'aluminium. Systeme de deSignation applicable aux
d'aluminium. Barres et tubes etires. Partie 3 : barres lingots pour refusion en aluminium allie ou non allie,
rondes, tolerances sur dimensions et forme. aux alliages-meres et aux produits moules. Partie 1 :
Statut :Homologuee systeme de deSignation numerique.
Statut :Homologuee
NF EN 754-4 Decembre 1995 : Aluminium et alliages
d'aluminium. Barres et tubes etires. Partie 4 : barres NF EN 1780-2 Decembre 1996: Aluminium et alliages
carrees, tolerances sur dimensions et forme. d'aluminium. Systeme de designation applicable aux
Statut :Homologuee lingots pour refusion en aluminium allie ou non allie,
aux alliages-meres et aux produits moules. Partie 2 :
NF EN 754-5 Decembre 1995 : Aluminium et alliages systeme de designation base sur les!symboles
d'aluminium. Barres et tubes etires. Partie 5 : barres chimiques. Statut :Homologuee
rectangulaires, tolerances sur dimensions et forme.
Statut :Homologuee NF EN 1780-3 Decembre 1996 : Aluminium et alliages
d'aluminium. Systeme de deSignation applicable aux
NF EN 754-6 Decembre 1995 : Aluminium et alliages lingots pour refusion en aluminium allie ou non allie,
d'aluminium. Barres et tubes etires. Partie 6 : barres aux alliages-meres et aux produits moules. Partie 3 :
hexagonales, tolerances sur dimensions et forme. regles d'ecriture pour la composition chimique.
Statut :Homologuee Statut :Homologuee
NF EN 755-1 Juillet 1997 : Aluminium Et Alliages NF EN 2004-1 Novembre 1993 : Serie aerospatiale.
D'aluminium - Barres, Tubes Et Profiles Files - Partie 1 Methodes d'essais applicables aux produits en
: Conditions Techniques De Controle Et De Livraison. aluminium et alliages d'aluminium. Partie 1 :
(Rem place NF A 01-101, Novembre 1972) determination de la conductivite electrique des alliages
Statut :Homologuee d'aluminium corroyes. Statut :Homologuee
NF EN 755-2 Juillet 1997 : Aluminium Et Alliages NF EN 2004-5 Novembre 1993 : Serie aerospatiale.
D'aluminium - Barres, Tubes Et Profiles Files - Partie 2 Methodes d'essais applicables aux produits en
: Caracteristiques Mecaniques. (Rem place En Partie aluminium et alliages d'aluminium. Partie 5 : mesure de
NF A 50-411, Avril 1989) Statut :Homologuee I'epaisseur du placage et de la diffusion du cuivre dans
NF EN 755-3 AoOt 1995: Aluminium et alliages Ie placage des demi-produits plaques.
d'aluminium. Barres, tubes et profiles files. Partie 3 : Statut :Homologuee
barres rondes, tolerances sur dimensions et forme. NF EN 2070-1 Decembre 1993 : Serie aerospatiale. Demi-
Statut :Homologuee produits corroyes en aluminium et alliages d'aluminium
NF EN 755-4 AoOt 1995 : Aluminium et alliages - Specification technique. Partie 1 :exigences
d'aluminium. Barres, tubes et profiles files. Partie 4 : generales. Statut :Homologuee
barres carrees, tolerances sur dimensions et forme. NF EN 2070-2 Mai 1990: Serie aerospatiale. Demi-produits
Statut :Homologuee corroyes en aluminium et alliages d'aluminium -
NF EN 755-5 AoOt 1995 : Aluminium et alliages SpeCification technique. Partie 2 : t61es minces, bandes
d'aluminium. Barres, tubes et profiles files. Partie 5 : profiles plies et t61es epaisses. Statut :Homologuee
barres rectangulaires, tolerances sur dimensions et
NF EN 2070-3 Mai 1990: Serie aerospatiale. Demi-produits
forme. Statut :Homologuee
corroyes en aluminium et alliages d'aluminium.
NF EN 755-6 AoOt 1995 : Aluminium et alliages Specification technique - Partie 3 : barres et profiles.
d'aluminium. Barres, tubes et profiles files. Partie 6 : Statut :Homologuee
barres hexagonales, tolerances sur dimensions et
NF EN 2070-4 Mai 1990: Serie aerospatiale. Demi-produits
forme. Statut :Homologuee corroyes en aluminium et alliages d'aluminium -
NF EN 851 Septembre 1995 : Aluminium et alliages Specification technique. Partie 4 : tubes pour
d'aluminium. Disques et ebauches pour disques pour application structurale. Statut :Homologuee
applications culinaires. Specifications.
NF EN 2070-5 Mai 1990 : Serie aerospatiale. Demi-produits
Statut :Homologuee
corroyes en aluminium et alliages d'aluminium -
NF EN 941 AoOt 1995: Aluminium et alliages d'aluminium. Specification technique. Partie 5 : tubes pour
Disques et ebauches pour disques pour applications canalisations sous pression. Statut :Homologuee
generales. Specifications. Statut :Homologuee
NF EN 2070-6 Mai 1990 : Serie aerospatiale. Demi-produits
NF EN 1370 Fevrier 1997 Fonderie. : Contr61e de la corroyes en aluminium et alii ages d'aluminium -
rugosite de surface par comparateurs visotactiles .. Specification technique. Partie 6 : fils a rivets.
Statut :Homologuee Statut :Homologuee
NF EN 1386 Mai 1997 : Aluminium Et Alliages D'aluminium - NF EN 2070-7 Mai 1990: Serie aerospatiale. Demi-produits
Toles Relief Specifications - Statut :Homologuee corroyes en aluminium et alliages d'aluminium -
NF EN 1396 Mars 1997 : Aluminium et alliages d'aluminium. Specification technique. Partie 7 : produits corroyes
T61es et bandes revetues en bobine pour applications a
destines la forge. Statut :Homologuee
generales. Specifications. Statut :Homologuee NF EN 2076-1 Novembre 1993: Serie aerospatiale. Lingots
NF EN 1669 Decembre 1996: Aluminium et alliages et pieces moulees en alliages d'aluminium et de
d'aluminium. Methodes d'essai. Mesure de l'indice de magnesium. SpeCification technique - Partie 1 -
comes a I'emboutissage pour les t61es et les bandes. Exigences generales. Statut :Homologuee
Statut :Homologuee NF EN 2076-2 Mars 1990: Serie aerospatiale. Lingots et
NF EN 1676 Decembre 1996: Aluminium et alliages pieces moulees en alliages d'aluminium et de
d'aluminium. Lingots pour refusion en aluminium allie. magnesium. Specification technique - Partie 2 - Lingots
Specifications. Statut :Homologuee pour refusion. Statut :Homologuee
384 Appendix A - Standards
AFNOR NF EN Standards (Aluminium) - continued. NF EN 2149 Juin 1996: Serie aerospatiale. Rivets
NF EN 2076-3 Mars 1990 : Serie aerospatiale. Lingots et ordinaires, a tete ronde aplatie, en alliage d'aluminium
pieces moulees en alliages d'aluminium et de 5056A, anodises ou chromates, serie base inches.
magnesium. Specification technique - Partie 3 - Pieces NF EN 2257 Juillet 1997 : Serie Aerospatiale - Tubes
types et pieces de serie. Statut :Homologuee Circulaires Pour Structures En Aluminium Et Alliages
NF EN 2082-1 Decembre 1993 : Serie aerospatiale. D'aluminium - Diametres 6mm Inferieur Ou Egal D
Produits destines a la forge, pieces forgees et pieces Inferieur Ou Egal 100mm - Epaisseur 1mm Inferieur
matricees en alliage d'aluminium - Specification Ou Egal A Inferieur Ou Egal 6mm - Dimensions.
technique. Partie 1 : exigences generales. Statut :Homologuee
Statut :Homologuee NF EN 2258 Juillet 1997 : Serie Aerospatiale - Tubes
NF EN 2082-2 Avril 1990 : Serie aerospatiale. Produits Circulaires Pour Canalisations En Aluminium Et
destines a la forge, pieces forgees et pieces matricees Alliages D'aluminium - Diametres 3, 2mm Inferieur Ou
en alliage d'aluminium - Specification technique. Partie Egal D Inferieur Ou Egal 100mm - Epaisseur 0, 6mm
2 : produits destines a la forge. Statut :Homologuee Inferieur Ou Egal A Inferieur Ou Egal 2, 5mm -
Dimensions. Statut :Homologuee
NF EN 2082-3 Avril 1990 : Serie aerospatiale. Produits
destines a la forge, pieces forgees et pieces matricees NF EN 2284 Janvier 1992 : Serie aerospatiale. Anodisation
en alliage d'aluminium - Specification technique. Partie sulfurique de I'aluminium et des alliages d'aluminium
3 : pieces types et pieces de serie. Statut :Homologuee corroyes. Statut :Homologuee
NF EN 2089 Avril 1994 : Serie aerospatiale. Alliage NF EN 2285 Mai 1990: Serie aerospatiale. Bagues
d'aluminium AI-P2014A - T6 ou T62 - Toles et bandes - cylindriques en alliage d'aluminium a garniture
a compris entre 0,4 mm et 6 mm. Statut :Homologuee autolubrifiante. Dimensions et charges.
Statut :Homologuee
NF EN 2092 Mars 1994 : Serie aerospatiale. Alliage
d'aluminium AI-P7075 - T6 ou T62 - Toles et bandes NF EN 2286 Mai 1990 : Serie aerospatiale. Bagues a
plaquees - a compris entre 0, 4 mm et 6 mm. epaulement en alii age d'aluminium a garniture
Statut :Homologuee autolubrifiante. Dimensions et charges.
Statut :Homologuee
NF EN 2093 Janvier 1993 : Serie aerospatiale. Alliage
d'aluminium AI-P7009 - T74 - Pieces forgees 20 mm < NF EN 2289 Novembre 1996 : Serie aerospatiale. Corps de
a < 150 mm. Statut :Homologuee bielle en alliage d'aluminium pour commandes de vol.
Specification technique. Statut :Homologuee
NF EN 2094 Janvier 1993 : Serie aerospatiale. Alliage
d'aluminium AI-P7009 - T74 - Pieces matricees 3 mm < NF EN 2318 Janvier 1993 : Serie aerospatiale. Alliage
a < 150 mm. Statut :Homologuee d'aluminium AI-P2024 - T3511 - Barres et profiles files
1,2 mm < a ou D < 150 mm. Statut :Homologuee
NF EN 2100 Janvier 1993 : Serie aerospatiale. Alliage
d'aluminium AI-P2014A - T4511 - Barres et profiles NF EN 2326 Janvier 1993 : Serie aerospatiale. Alliage
files a ou D < 200 mm. Statut :Homologuee d'aluminium AI-P6082 - T6 - Barres et profiles files a ou
D < 200 mm. Statut :Homologuee
NF EN 2101 Janvier 1992: Serie aerospatiale. Anodisation
chromique de I'aluminium et des alliages d'aluminium NF EN 2365 AoOt 1989: Serie aerospatiale. Bagues en
corroyes. Statut :Homologuee alliage d'aluminium. Statut :Homologuee
NF EN 2122 Avril 1996 : Serie Aerospatiale - Rondelles NF EN 2381 Janvier 1993 : Serie aerospatiale. Alliage
Plates, En Alliage D'aluminium, Anodisees Ou d'aluminium AI-P7009 - T7452 - Pieces forgees 40 mm
Chromatees (Remplace NF EN 2122, Novembre 1994) < a <150 mm. Statut :Homologuee
Statut :Homologuee NF EN 2384 Janvier 1993 : Serie aerospatiale. Alliage
NF EN 2126 Janvier 1993 : Serie aerospatiale. Alliage d'aluminium AI-P2014A - T6511 - Barres et profiles
d'aluminium AI-P7075 - T651 - Toles epaisses - 6 mm files a ou D < 150 mm. Statut :Homologuee
< a < 80 mm. Statut :Homologuee NF EN 2385 Janvier 1993 : Serie aerospatiale. Alliage
NF EN 2127 Janvier 1993: Serie aerospatiale. Alliage d'aluminium AI-P7009 - T74511 - Barres et profiles files
d'aluminium AI-P7075 - T73511 - Barres et profiles files a ou D <125 mm. Statut :Homologuee
a ou D < 100 mm. Statut :Homologuee NF EN 2395 Avril 1994 : Serie aerospatiale. Alliage
NF EN 2128 Janvier 1993 : Serie aerospatiale. Alliage d'aluminium AI-P2014A - T4 ou T42 - Toles et bandes-
d'aluminium AI-P7075 - T7351 - Barres etirees 6 mm < a compris entre 0,4 mm et 6 mm. Statut :Homologuee
a ou D < 75 mm. Statut :Homologuee XP EN 2500-2PR Fevrier 1997 : Serie aerospatiale.
NF EN 2144 Novembre 1994: Serie aerospatiale. Rivets Instructions pour la preparation et I'utilisation des
ordinaires, a tete ronde aplatie, en alliage d'aluminium normes de materiaux metalliques. Partie 2 : exigences
2117. Serie base inches. Statut :Homologuee specifiques a I'aluminium, aux alliages d'aluminium et
aux alliages de magnesium. Statut :Experimentale
NF EN 2145 Novembre 1994 : Serie aerospatiale. Rivets
a
ordinaires, tete ronde aplatie, en alliage d'aluminium NF EN 2536 Novembre 1995 : Serie aerospatiale.
Anodisation dure des alliages d'aluminium.
2117, anodises ou chromates. Serie base inches.
Statut :Homologuee Statut :Homologuee
NF EN 2146 Avril 1993 : Serie aerospatiale. Rivets NF EN 2551 Avril 1993 : Serie aerospatiale. Rivets
ordinaires, a tete ronde aplatie, en alliage d'aluminium ordinaires, a tete fraisee 100 degres normales avec
2017A, serie base inches. Statut :Homologuee dome, en alliage d'aluminium en 2117, serie base
inches. Statut :Homologuee
NF EN 2148 Avril 1993 : Serie aerospatiale. Rivets
ordinaires, a tete ronde aplatie, en alliage d'aluminium NF EN 2552 Avril 1993 : Serie aerospatiale. Rivets
5056A, serie base inches. Statut :Homologuee ordinaires, a tete fraisee 100 degres normale avec
dome, en alliage d'aluminium 2117, serie base inches.
Statut :Homologuee
Appendix A - Standards 385
AFNOR NF EN Standards (Aluminium) - continued. EN 4004PR Novembre 1994: Serie aerospatiale. Alliage
NF EN 2553 Avril 1993 : Serie aerospatiale. Rivets d'aluminium AI-P3103-, H16 - Toles et bandes - a
ordinaires, a tete fraisee 100 degres normale avec compris entre O.4mm et 6 mm. Statut :Experimentale
dome, en alliage d'aluminium 2017A, serie base EN 4005PR Novembre 1994 : Serie aerospatiale. Alliage
inches. Statut :Homologuee d'aluminium AI-P5052-, 0 - Toles et bandes - a
NF EN 2555 Avril 1993 : Serie aerospatiale. Rivets compris entre 0.3 mm et 6 mm. Statut :Experimentale
ordinaires, a tete fraisee 100 degres normale avec EN 4006PR Novembre 1994 : Serie aerospatiale. Alliage
dome, en alliage d'aluminium 5056A, serie base d'aluminium AI-P6082, T4 ou T42 - Toles et bandes - a
inches. Statut Homologuee compris entre 0.4 mm et 6 mm .. Statut :Experimentale
NF EN 2556 Avril 1993 : Serie aerospatiale. Rivets EN 4007PR Novembre 1994 : Serie aerospatiale. Alliage
ordinaires, a tete fraisee 100 degres normale avec d'aluminium AI-P6082-, T6 ou T62 - Toles et bandes -
dome, en alliage d'aluminium 5056A, anodises ou a compris entre 0.4 mm et 6 mm. Statut :Experimentale
chromates, serie base inches. Statut :Homologuee EN 4099PR Novembre 1994 : Serie aerospatiale. Alliage
NF EN 2630 Avril 1994 : Serie aerospatiale. Alliage d'aluminium AI-P2219-, T62 - Toles et bandes
d'aluminium AI-P7009- - T74511 - Barres et profiles plaquees - a compris entre 0.5 mm et 6 mm.
files - a ou D inferieur ou egal a 125 mm avec controle Statut :Experimentale
de la zone peripherique a gros grains. EN 4100PR Novembre 1994 : Serie aerospatiale. Alliage
Statut :Homologuee d'aluminium AI-P2219-, T62 - Toles et bandes - a
NF EN 2632 Avril 1994 : Serie aerospatiale. Alliage compris entre 0.5 mm et 6 mm. Statut :Experimentale
d'aluminium AI-P7075- - T73511 - Barres et profiles EN 4101 PR Novembre 1994 : Serie aerospatiale Alliage
files - a ou D inferieur ou egal a 100 mm avec controle d'aluminium AI-P2024-, T4 - Toles et bandes avec
de la zone peripherique a gros grains. aptitude amelioree a I'etirage sur forme - a compris
Statut :Homologuee entre 0.4 mm et 6 mm. Statut :Experimentale
NF EN 2633 Avril 1994 : Serie aerospatiale. Alliage EN 4102PR Novembre 1994 : Serie aerospatiale. Alliage
d'aluminium AI-P2024- - T3511 - Barres et profiles files d'aluminium AI-P2219-, T81 - Toles et bandes
- a ou D compris entre 1.2 mm et 150 mm avec plaquees - a compris entre 0.5 mm et 6 mm.
controle de la zone peripherique a gros grains. Statut :Experimentale
Statut :Homologuee
XP EN 4500-2PR Avril 1997 : Serie Aerospatiale -
NF EN 2636 Avril 1994: Serie aerospatiale. Alliage Materiaux Metalliques - Regles Pour La Redaction Et
d'aluminium AI-P6082- - T6 - Barres et profiles files - a La Presentation Des Normes De Materiaux - Partie 2 :
ou D inferieur ou egal a 200 mm, avec contra Ie de la Regles Specifiques A L'aluminium, Aux Alliages
zone peripherique a gros grains. Statut :Homologuee D'aluminium Et De Magnesium. Statut :Experimentale
NF EN 2693 Mars 1994 : Serie aerospatiale. Alliage XP EN 4500-2PR Fevrier 1997 : Serie aerospatiale.
d'aluminium AI-P5086 - H111 - Toles et bandes - a Materiaux metalliques. Regles pour la redaction et la
compris entre 0.3 mm et 6mm. Statut :Homologuee presentation des normes de materiaux. Partie 2 :
NF EN 2694 Mars 1994 : Serie aerospatiale. Alliage regles specifiques a I'aluminium, aux alliages
d'aluminium AI-P6061 - T6 ou T62 - Toles et bandes - d'aluminium et aux alliages de magnesium.
a compris entre 0.4 mm et 6 mm. Statut :Homologuee Statut :Experimentale
NF EN 2695 Mars 1994 : Serie aerospatiale. Alliage NF EN 10154 Aout 1996 : Bandes et tales en acier revetues
d'aluminium AI-P6081 - T6 - Toles et bandes - a en continu par immersion a chaud d'une couche
compris entre 0.3 mm et 6 mm. Statut :Homologuee d'aluminium-silicium (AS). Conditions techniques de
NFEN 2696 Mars 1994 : Serie aerospatiale. Alliage livraison. Statut :Homologuee
d'aluminium AI-P7075 - T6 ou T62 - Toles et bandes - NF EN 10214 Novembre 1995: Bandes et tales en acier
a compris entre 0.4 mm et 6 mm. Statut :Homologuee revetues a chaud en continu d'alliage zinc-aluminium
NF EN 2912 Mai 1996 : Serie aerospatiale. Rondelies plates (ZA). Conditions techniques de livraison.
larges, en alliage d'aluminium, anodisees ou Statut :Homologuee
chromatees. Statut :Homologuee NF EN 10215 Novembre 1995 : Bandes et t6les en acier
EN 3474PR Novembre 1994 : Serie aerospatiale. Alliage revetues d'alliage aluminium-zinc (AZ) a chaud en
d'aluminium AI-P2024-, T81 - Toles et bandes - a continuo Conditions techniques de livraison.
compris entre 0.25 mm et 6 mm. Statut :Experimentale Statut :Homologuee
XP EN 3869PR Fevrier 1995 : Serie aerospatiale. Raccords, NF EN 22063 Janvier 1994 : Revetements metalliques et
brides amovibles et joints - Joints en elastomere inorganiques. Projection thermique. Zinc, aluminium et
fluorocarbone et armature en alliage d'aluminium. alliages de ces metaux. Statut :Homologuee
Statut :Experimentale NF EN 23134-1 Decembre 1991 : Metaux legers et leurs
EN 3996PR Novembre 1994: Serie aerospatiale. alliages - Termes et definitions - Partie 1 : materiaux.
Aluminium AI-P1100-, H14 - Toles et bandes - a Statut :Homologuee
compris entre 0.3 mm et 6 mm. Statut :Experimentale NF EN 23134-2 Decembre 1991 : Metaux legers et leurs
EN 3997PR Novembre 1994 : Serie aerospatiale. Alliage alliages - Termes et definitions - Partie 2 - Formes
d'aluminium AI-P2024-, T3 - Toles et bandes - a brutes. Statut :Homologuee
compris entre 0.4 mm et 6 mm. Statut :Experimentale NF EN 23134-3 Decembre 1991 : Metaux legers et leurs
EN 3998PR Novembre 1994 : Serie aerospatiale. Alliage alliages - Termes et definitions - Partie 3 - Produits
d'aluminium AI-P2024-, T42 - Toles et bandes - a corroyes. Statut :Homologuee
compris entre 0.4 mm et 6 mm. Statut :Experimentale
386 Appendix A - Standards
AFNOR NF EN Standards (Aluminium) - continued. EN Standards
NF EN 30042 Juillet 1994: Assemblages en aluminium et
alliages d'aluminium soudables soudes a I'arc. Guide European EN specifications for metal alloys are currently
des niveaux d'acceptation des defauls. being generated & adopted. These will progressively
Statut :Homologuee supersede the various national standards for aluminium
NF EN 50064 + AMDT 1 Novembre 1993 : Enveloppes en alloys, as with other materials. However, it will be some
aluminium et alliage d'aluminium corroyes pour years before this process is completed & fully implemented
I'appareillage a haute tension sous pression de gaz. in all European countries. Aerospace EN designations apply
StatutHomologuee to particular alloys, forms & conditions (many of these are
still at the provisional stage). However, there are several EN
NF EN 50069 + AMDT 1 Novembre 1993 : Enveloppes specifications which cover the basic characteristics of
soudees en alliage d'aluminium comportant des parties general engineering aluminium alloys
moulees et des parties en metal corroye pour
I'appareillage a haute tension sous pression de gaz. o Chemical composition specifications for wrought
Statut :Homologuee aluminium alloys are now contained in a single CEN
specification: EN 573 - Aluminium & aluminium alloys -
NF ISO Standards Chemical composition & form of wrought products.
NF ISO 2767 Juillet 1988 : Traitements de surface. o Temper designations for wrought aluminium alloys are
Aluminium et alliage d'aluminium anodises. Reflectivite also contained in a single CEN specification: EN 515 -
speculaire a 45 degres - Retlectivite totale - Nettete Aluminium & aluminium alloys - Wrought products
d'image. Statut :Homologuee temper designations.
NF ISO 6719 Juillet 1988 : Traitements de surface. U EN 485 now contains conditions for delivery, properties
Aluminium et alliage d'aluminium anodises. Mesurage & tolerances for wrought aluminium alloy products.
des caracteristiques de reflectivite des surfaces Similar specifications will be issued in the future to cover
d'aluminium a I'aide d'instruments integrateurs cast aluminium alloys.
spheriques. Statut :Homologuee
EN 12373-11 (Norm-Entwurf), Publication: 1997-02 :
NF ISO 7668 Juillet 1988 : Traitements de surface. Aluminium & aluminium alloys - Anodizing - Part 11 :
Aluminium et alliage d'aluminium anodises. Mesurage Measurement of specular reflectance & specular gloss
des caracteristiques de reflectance et de brillant of anodic oxidation coatings at angles of 20,45, 60
speculaires a angle fixe de 20 degres, 45 degres, 60 oder 85; German version prEN 12373-11 :1996.
degres ou 85 degres. Statut :Homologuee
EN 12373-13 (Norm-Entwurf), Publication:1997-02:
NF ISO 7669 Juillet 1988 : Traitements de surface. Aluminium & aluminium alloys - Anodizing - Part 13
Aluminium et alliage d'aluminium anodises. Mesurage Measurement of reflectance characteristics of
de la reflectivite totale a I'aide d'un reflectometre aluminium surfaces using integrating-sphere
photoelectrique. Statut :Homologuee instruments; German version prEN 12373-13: 1996.
NF ISO 8251 Juillet 1988 : Traitements de surface. EN 12373-3 (Norm-Entwurf), Publication:1996-11 :
Aluminium et alliages d'aluminium anodises. Aluminium & aluminium alloys - Anodizing - Part 3:
Determination de la resistance a I'usure et de I'indice Estimation of loss of absorptive power of anodic
d'usure des couches d'oxyde anodiques par essai a la oxidation coatings after sealing; dye spot test with prior
roue abrasive. Statut :Homologuee acid treatment; German version prEN 12373-3: 1996.
NF ISO 8993 Decembre 1989 : Aluminium et alliages EN 12373-5 (Norm-Entwurf), Publication 1996-11 :
d'aluminium anodises. Systeme de cotation de la Aluminium & aluminium alloys - Anodizing - Part 5:
corrosion par piqOres - Methode reposant sur des Assessment of quality of sealed anodic oxidation
images-types. Statut :Homologuee coatings by measurement of the loss of mass after
NF ISO 8994 Decembre 1989 : Aluminium et alliages immersion in phosphoric acid/chromic acid solution
d'aluminium anodises. Systeme de cotation de la without prior acid treatment; German version prEN
corrosion par piqOres - Methode par quadrillage. 12373-5: 1996.
Statut :Homologuee EN 12373-6 (Norm-Entwurf), Publication 1996-11 :
NF ISO 9717 Juillet 1991 : Couches de conversion au Aluminium & aluminium alloys - Anodizing - Part 6:
phosphate sur metaux - Methode de specification des Assessment of quality of sealed anodic oxidation
caracteristiques. (2e tirage. juillet 1991). coatings by measurement of the loss of mass after
Statut :Homologuee immersion in phosphoric acid/chromic acid solution
with prior acid treatment; German version prEN 12373-
NF Others 61996.
REGLES AL Juillet 1976 : Regles AL - Regles de EN 12373-7 (Norm-Entwurf), Publication:1996-11 :
conception et de calcul des charpentes en alliages Aluminium & aluminium alloys - Anodizing - Part 7:
d'aluminium .. Statut :Document de DTU Determination of the comparative fastness to ultra-
violet light & heat of coloured anodic oxidation
FD CR 12187 Avril 1996 : Soudage. Lignes directrices pour
coatings; German version prEN 12373-7: 1996.
un groupement des materiaux pour Ie soudage.
Statut :Fascicule de doc. EN 1370 Fevrier 1997 Fonderie. : Contrale de la rugosite de
surface par comparateurs visotactiles ..
FD CR 12361 Octobre 1996: Essais destructifs des
Statut :Homologuee
soudures sur materiaux metalliques. Reactifs pour
examen macroscopique et microscopique. EN 1386 Mai 1997 : Aluminium et alliages d'aluminium -
Statut :Fascicule de doc. Toles relief specifications - Statui :Homologuee
EN 1386 Mai 1997 : Aluminium et alii ages d'aluminium -
Toles relief specifications - Statut :Homologuee
Appendix A Standards 387
EN Standards (Aluminium) - continued. EN 2004-7 (Norm-Entwurf), Publication 1996-07 :
EN 1396 Mars 1997 : Aluminium et alliages d'aluminium. Aerospace series - Test methods for aluminium &
Toles et bandes revetues en bobine pour applications aluminium alloy products - Part 7: Reference blocks for
generales. Specifications. Statut :Homologuee the calibration of measuring equipment used in the
determination of electrical conductivity of wrought
EN 1669 Decembre 1996 : Aluminium et alliages
aluminium & aluminium alloys.
d'aluminium. Methodes d'essai. Mesure de I'indice de
a
cornes I'emboutissage pour les toles et les bandes. EN 2070 : Specification for aluminium & aluminium alloy
Statut :Homologuee wrought products. Technical specification
EN 2806PR : 2024-T42 extruded sections, 1.2mm s; a s; EN 3552PR : 2618A-T6 clad sheet & strip, 0.4mm :<: a:<::
100mm, peripheral coarse grain control); 6mm);
EN 2807PR : 7020-T6 extruded sections 1.2mm s; a :<: EN 3553PR : 2618A-T6511 extruded bar & section, 1.2mm
100mm, peripheral coarse grain control :<: a:<:: 100mm);
EN 2813PR : 6061-T6 tube for hydraulics, 0.6mm s; a:<:: EN 3554PR : 7010-T7652 hand forgings, a s; 200mm
12.5mm EN 3555PR : 7075-T79510 extruded bar & section, 1.2mm
EN 2814PR : 2024-T3511 tube for structures, 0.6mm s; as; :<:: aId s; 100mm, coarse grain control
12.5mm EN 3657PR : 2024-T351 0 drawn bar for machining, d s;
EN 286-4 : Aluminium alloy pressure vessels designed for 75mm
air-braking equipment & auxiliary pneumatic equipment EN 3702PR : 6061-T4 tube for hydraulics, 0.6mm s; a s;
for railway rolling stock. 12.5mm
a
EN 286-4 Decembre 1994 : Recipients pression simples, EN 3869PR Fevrier 1995: Serie aerospatiale. Raccords,
a a
non soumis la flamme, destines contenir de I'air ou brides amovibles et jOints - Joints en elastomere
de I'azote. Partie 4 : recipients a pression en alliages fluorocarbone et armature en alliage d'aluminium.
d'aluminium destines aux equipements pneumatiques Statut :Experimentale
de freinage et aux equipements pneumatiques
EN 3996PR : 11 00-H14 sheet & strip, 0.3mm s; a s; 6mm)
auxiliaires du ma Statut :Homologuee
EN 3996PR Novembre 1994 : Serie aerospatiale.
EN 287-2 : Aluminium & aluminium alloys - approval testing
Aluminium AI-P1100-H14 - Toles et bandes - a compris
of welders for fusion welding.
entre 0.3 mm et 6 mm. Statut :Experimentale
EN 287-2 Juin 1992 : Epreuve de qualification des
EN 3997PR : 2024-T3 sheet & strip, O.4mm :<: aId :<: 6mm
soudeurs. Soudage par fusion. Partie 2 : aluminium et
ses alliages. Statut :Homologuee EN 3997PR Novembre 1994 : Serie aerospatiale. Alliage
d'aluminium AI-P2024-T3 - Toles et bandes - a compris
EN 288-4 : Welding procedure tests for the arc welding of
entre 0,4 mm et 6 mm. Statut :Experimentale
aluminium & its alloys
EN 288-4 Mai 1993 : Descriptif et qualification d'un mode EN 3998PR : 2024-T42 sheet & strip, O.4mm s; aId S; 6mm
operatoire de soudage pour les materiaux metalliques. EN 3998PR Novembre 1994 : Serie aerospatiale. Alliage
Partie 4 : epreuve de qualification d'un mode operatoire d'aluminium AI-P2024-T42 - Toles et bandes - a
a
de soudage I'arc sur I'aluminium et ses alliages. compris entre 0, 4 mm et 6 mm. Statut :Experimentale
Statut :Homologuee EN 4004PR : 3103-H16 sheet & strip, 0.4mm:<:: a:<:: 6mm)
EN 2912 Mai 1996 : Serie aerospatiale. Rondelles plates EN 4004PR Novembre 1994: Serie aerospatiale. Alliage
larges, en alliage d'aluminium, anodisees ou d'aluminium AI-P3103-H16 - Toles et ban des - a
chromatees. Statut :Homologuee compris entre 0, 4mm et 6 mm. Statut :Experimentale
EN 30042 Juillet 1994 : Assemblages en aluminium et EN 4005PR : 5052-0 sheet & strip, 0.3mm s; a s; 6mm)
a
alliages d'aluminium soudables soudes I'arc. Guide
EN 4005PR Novembre 1994 : Serie aerospatiale. Alliage
des niveaux d'acceptation des defauts.
Statut :Homologuee d'aluminium AI-P5052-0 - Toles et bandes - a compris
entre 0,3 mm et 6 mm. Statut :Experimentale
EN 3334PR : 7050-T651 plate, 6mm s; a s; 60mm);
EN 4006PR : 6082-T41T42 sheet & strip, 0.4mm :<:: a S; 6mm
EN 3337PR : 7010-T74511 extruded bars & sections aId s;
EN 4006PR Novembre 1994 : Serie aerospatiale. Alliage
130mm, peripheral coarse grain control);
d'aluminium AI-P6082-T4 ou T42 - Toles et bandes - a
EN 3338PR : 7050-T74511 extruded bars & sections aId s; compris entre 0, 4 mm et 6 mm .. Statut :Experimentale
130mm, peripheral coarse grain control);
EN 4007PR : 6082-T61T62 sheet & strip, 0.4mm s; a s; 6mm)
EN 3339PR : 7010-T76 die forgings, a:<:: 200mm
EN 3340PR : 7050-T76 die forgings, a:<:: 200mm
EN 3341PR: 6061-T4 sheet & strip, 0.4mm:<:: a:<:: 6mm)
392 Appendix A - Standards
EN Standards (Aluminium) - continued. EN 485-2 Decembre 1994 : Aluminium et alliages
EN 4007PR Novembre 1994 : Serie aerospatiale. Alliage d'aluminium. Toles, bandes et tales epaisses. Partie 2 :
d'aluminium AI-P6082-T6 ou T62 - Tales et bandes - a caracteristiques mecaniques. Statut :Homologuee
compris entre 0, 4 mm et 6 mm. Statut :Experimentale EN 485-3 : Tolerance on shape & dimensions for hot-rolled
EN 4099PR : 2219-T62 clad sheet & strip, 0.5mm ~ a ~ products
6mm EN 485-3 Juin 1994 : Aluminium et alliages d'aluminium.
EN 4099PR Novembre 1994 : Serie aerospatiale. Alliage Toles, ban des et tales epaisses. Partie 3 : tolerances
d'aluminium AI-P2219-T62 - Toles et bandes plaquees sur forme et dimensions des produits lamines a chaud.
- a compris entre 0,5 mm et 6 mm. Statut :Homologuee
Statut :Experimentale EN 485-4 : Tolerance on shape & dimensions for cold-rolled
EN 4100PR : 2219-T62 sheet & strip, 0.5mm ~ a ~ 6mm products
EN 4100PR Novembre 1994: Serie aerospatiale. Alliage EN 485-4 Juin 1994: Aluminium et alliages d'aluminium.
d'aluminium AI-P2219-, T62 - Toles et bandes - a Toles, ban des et tales epaisses. Partie 4 : tolerances
compris entre 0, 5 mm et 6 mm. Statut :Experimentale sur forme et dimensions des produits lamines a froid.
Statut :Homologuee
EN 4101 PR : 2024-T4 sheet & strip, O.4mm ~ aid ~ 6mm)
EN 486 : Aluminium & aluminium alloys. Extrusion ingots.
EN 4101 PR Novembre 1994 : Serie aerospatiale. Alliage SpeCifications
d'aluminium AI-P2024-T4 - Toles et bandes avec
aptitude amelioree a I'etirage sur forme - a compris EN 486 Mars 1994 : Aluminium et alliages d'aluminium.
entre 0, 4 mm et 6 mm. Statut :Experimentale Billettes de filage. SpeCifications. Statut :Homologuee
EN 487 : Aluminium & aluminium alloys. Rolling ingots.
EN 4102PR: 2219-T81 clad sheet & strip, 0.5mm ~ a ~
Specifications
6mm)
EN 487 Mars 1994 : Aluminium et alliages d'aluminium.
EN 41 02PR Novembre 1994 : Serie aerospatiale. Alliage
Plaques de laminage. Specifications.
d'aluminium AI-P2219-T81 - Toles et bandes plaquees
Statut :Homologuee
- a compris entre 0,5 mm et 6 mm.
Statut :Experimentale EN 50064 + AMDT 1 Novembre 1993 : Enveloppes en
aluminium et alliage d'aluminium corroyes pour
EN 4500-2PR Avril 1997 : Serie aerospatiale - Materiaux
metalliques - Regles pour la redaction et la
a
I'appareillage haute tension sous pression de gaz.
Statut :Homologuee
presentation des normes de materiaux - Partie 2 :
regles specifiques a I'aluminium, aux alliages EN 50069 + AMDT 1 Novembre 1993 : Enveloppes soudees
d'aluminium et de magnesium. Statut :Experimentale en alliage d'aluminium comportant des parties moulees
EN 4500-2PR Avril 1997 : Serie aerospatiale - Materiaux
et des parties en metal corroye pour I'appareillage a
haute tension sous pression de gaz.
metalliques - Regles pour la redaction et la
Statut :Homologuee
presentation des normes de materiaux - Partie 2 :
regles specifiques a I'aluminium, aux alliages EN 515 : Aluminium alloys. Wrought products. Temper
d'aluminium et de magnesium. Statut :Experimentale designations
EN 4500-2PR Avril 1997 : Serie aerospatiale - Materiaux EN 515 Octobre 1993: Aluminium et alliages d'aluminium.
metalliques - Regles pour la redaction et la Produits corroyes. Designation des etats
presentation des normes de materiaux - Partie 2 : metallurgiques. Statut :Homologuee
regles specifiques a I'aluminium, aux alliages EN 541 : Aluminium & aluminium alloys. Rolled products for
d'aluminium et de magnesium. Statut :Experimentale cans, closures & lids. Specifications
EN 4500-2PR Fevrier 1997 : Serie aerospatiale - Materiaux EN 541 Avril 1995 : Aluminium et alliages d'aluminium.
metalliques - Regles pour la redaction et la Produits lamines pour boites, capsules rigides et
presentation des normes de materiaux - Partie 2 : couvercles. Specifications. Statut :Homologuee
regles specifiques a I'aluminium, aux alliages EN 546-1 Decembre 1996 : Aluminium et alliages
d'aluminium et aux alliages de magnesium. d'aluminium. Feuille mince. Partie 1 : conditions
Statut :Experimentale techniques de contrale et de livraison.
EN 4500-2PR Fevrier 1997 : Serie aerospatiale. Materiaux Statut :Homologuee
metalliques. Regles pour la redaction et la presentation EN 546-2 Decembre 1996 : Aluminium et alliages
des normes de materiaux. Partie 2 : regles specifiques d'aluminium. Feuille mince. Partie 2 : caracteristiques
aI'aluminium, aux alliages d'aluminium et aux alliages mecaniques. Statut :Homologuee
de magnesium. Statut :Experimentale
EN 546-3 Decembre 1996 : Aluminium et alliages
EN 4500-2PR Fevrier 1997 : Serie aerospatiale. Materiaux d'aluminium. Feuille mince. Partie 3 :tolerances sur
metalliques. Regles pour la redaction et la presentation dimensions. Statut :Homologuee
des normes de materiaux. Partie 2 : regles specifiques
EN 570 : Aluminium & aluminium alloys. Impact extrusion
aI'aluminium, aux alliages d'aluminium et aux alliages
slugs obtained from wrought products. Specification.
de magnesium. Statut :Experimentale
EN 570 Octobre 1994 : Aluminium et alliages d'aluminium.
EN 485 : Aluminium & aluminium alloys. Sheet strip & plate
a
Pions de filage par choc obtenus partir de produits
EN 485-1 : Technical conditions for inspection & delivery corroyes. Specifications. Statut :Homologuee
EN 485-1 Juin 1994 : Aluminium et alliages d'aluminium. EN 573 : Aluminium & aluminium alloys. Chemical
Toles, ban des et tales epaisses. Partie 1 : conditions composition & form of wrought products.
techniques de controle et de livraison.
Statut :Homologuee EN 573-1 : Numerical designation system
GOST - CIS (exUSSR) H2211 (Jan. 1992) : Aluminium Alloy Ingots for Castings.
H2212 (Jan. 1976) : Aluminium Base Alloy in Ingots for
2685-75 (Feb. 1985) : Aluminium Casting Alloys, Grades, Diecastings.
Specifications & Test Methods.
H5302 (Jan. 1990) : Aluminium Alloys, Diecastings.
OS - Denmark
KS - Korea
DS 3002-4162 (May 1971) : Aluminium Alloys for Castings.
D2330-1985 (Jan. 1985) : Aluminium Alloy Ingot for
Castings.
SFS - Finland
2560-2574 (1985) : Cast Aluminium Alloys. NS - Norway
Aluminium Casting Alloys:
UNI-ltaly
NS 17510 (1988).
Aluminium Casting Alloys: NS 17512 (1988).
3040 (1950). NS 17520 (1988).
3041 (1950). NS 17525 (1988).
3042 (1950). NS 17530 (1971).
3043 (1950). NS 17535 (1989).
3044 (1950).
Appendix A - Standards 395
NS Norway (Aluminium) - Continued SS 144253 (1986),
NS 17540 (1989), SS 144255 (1982),
NS 17550 (1971), SS 144260 (1986).
NS 17570 (1971), SS 144261 (1982).
NVS F 2022 (1988), SS 144263 (1986).
NVS F 2023 (1988). SS 144282 (1986),
SS 144283 (1986),
GB - China (PRC) SS 144337 (1986),
1173-86 (May 1987) : Cast Aluminium Alloys, Technical SS 144438 (1982),
Specifications.
VSM - Switzerland
SABS - South Africa 10895 (1976) : Aluminium Casting Alloys, Compositions and
989 (1970) properties of casting and test bars,
EN 23134-3 Decembre 1991 : Metaux legers et leurs ISO 2142:1981 : Wrought aluminium, magnesium & their
alliages - Termes et definitions - Partie 3 - Produits alloys - Selection of specimens & test pieces for
corroyes. Statut :Homologuee mechanical testing
EN 2500-2PR Fevrier 1997 : Serie aerospatiale. ISO 2353: 1972 : Magnesium & its alloys - Determination of
Instructions pour la preparation et I'utilisation des manganese in magnesium alloys containing zirconium,
normes de materiaux metalliques. Partie 2 : exigences rare earths, thorium & silver - Periodate photometric
a
specifiques I'aluminium, aux alliages d'aluminium et method
aux alliages de magnesium. Statut :Experimentale ISO 2354: 1976 : Magnesium alloys - Determination of
EN 2731 PR : MG-C-51-T6 Sand castings insoluble zirconium - Alizarin sulphonate photometric
method
EN 2732PR : MG-C-51-T6 Chill castings
ISO 2355: 1972 : Chemical analysis of magnesium alloys -
EN 2735PR : MG-C-91-T5 Sand castings Determination of rare earths - Gravimetric method
EN 2736PR : MG-C-91-T5 Chill castings ISO 2377:1972: Magnesium alloy sand castings-
EN 2738PR : MG-C-43-T5 Sand castings Reference test bar
EN 2739PR : MG-C-43-T5 Chill castings ISO 2437:1972 : Recommended practice for the X-ray
EN 2742PR : MG-C-71-F Sand castings inspection of fusion welded butt Joints for aluminium &
its alloys & magnesium & its alloys 5 to 50 mm thick
EN 4500-2PR Avril 1997 : Serie Aerospatiale - Materiaux
Metalliques - Regles Pour La Redaction Et La ISO 3115:1981: Castings in magnesium alloys containing
Presentation Des Normes De Materiaux - Partie 2 : zirconium - Chemical composition & mechanical
Regles Specifiques A L'aluminium, Aux Alliages properties
D'aluminium Et De Magnesium. Statut :Experimentale ISO 3116:1981 : Wrought magnesium alloys - Chemical
EN 4500-2PR Fevrier 1997 : Serie aerospatiale. Materiaux composition & mechanical properties
metalliques. Regles pour la redaction et la presentation ISO 3255:1974: Magnesium & magnesium alloys-
des normes de materiaux. Partie 2 : regles specifiques Determination of aluminium - Chromazurol S
aI'aluminium, aux alliages d'aluminium et aux alliages photometric method
de magnesium. Statut :Experimentale ISO 4058:1977: Magnesium & its alloys - Determination of
nickel - Photometric method using dimethylglyoxime
ISO Standards ISO 4194: 1981 : Magnesium alloys - Determination of zinc -
Flame atomic absorption spectrometric method
ISO 1211980 : Magnesium-aluminium-zinc alloy ingots &
alloy castings - Chemical composition & mechanical ISO 5196-1: 1980 : Magnesium alloys - Determination of
properties of sand cast reference test bars thorium - Part 1: Gravimetric method
ISO 791: 1973 : Magnesium alloys - Determination of ISO 5196-2:1980: Magnesium alloys - Determination of
aluminium - 8-hydroxyquinoline gravimetric method thorium - Part 2: Titrimetric method
ISO 791 : Magnesium alloys, analysis method for aluminium ISO 7773: 1983 : Magnesium alloys - Round bars & tubes -
content Dimensional tolerances
ISO 792:1973: Magnesium & magnesium alloys- ISO 82871984: Unalloyed magnesium ingots - Chemical
Determination of iron - Orthophenanthroline composition
photometric method ISO 99161991 : Aluminium alloy & magnesium alloy
ISO 792 : Magnesium & magnesium alloys, analysis method castings - Liquid penetrant inspection
for iron content
Appendix A - Standards 399
SAE Standards SAE/AMS 4422N (Apr-87) Magnesium Alloy Castings, Sand
6.0AI 3.0Zn Solution Heat Treated
SAE/AMS 4490G (Oct-88) Magnesium Alloy Castings, Die, SAE/AMS 4420M (Jan-92) Magnesium Alloy Castings, Sand
9.0AI 0.70Zn (AZ91 A-F), As Cast 6AI 3Zn, As Cast
SAE/AMS 4484J (Apr-92) Magnesium Alloy Castings, SAE/AMS 44198 (Apr-87) Magnesium Alloy Castings, Sand
Permanent Mold 9.0A 1 2.0Zn Solution and 2.5Ag 1.1Th 1.00i 0.70Zr (QH21-T6) Solution and
Precipitation Heat Treated Precipitation Heat Treated
SAE/AMS 4483C (Apr-92) Magnesium Alloy Castings, SAE/AMS 4418F (Oec-94) Magnesium Alloy, Sand
Permanent Mold 10AI Solution and Precipitation Heat Castings, 2.5Ag 2.1 Oi 0.70Zr Solution and Precipitation
Treated Heat Treated
SAE/AMS 44550 (Nov-94) Magnesium Alloy, Investment SAE/AMS 4417 (Oct-89) Castings, Sand, Magnesium Alloy,
Castings 10A1 (AM100A-T6) Solution and Precipitation 1.5Ag 2.lOi 0.08Cu 0.70Zr, Solution and PrecIpitation
Heat Treated Heat Treated
SAE/AMS 4453C (Nov-94) Magnesium Alloy, Investment SAE/AMS 4397A (May-68) Magnesium Wire, Welding 14Li
Castings 9.0AI 2.0Zn (AZ92A-T6) Solution and 1.25AI*
Precipitation Heat Treated
SAE/AMS 4396C (Oct-86) Magnesium Alloy Welding Wire
SAE/AMS 44528 (Nov-94) Magnesium Alloy, Investment 3.3Ce 2.5Zn O.72Zr (EZ33A)
Castings 8.7AI 0.70Zn 0.22Mn (AZ 91C-T6) Solution
and Precipitation Heat Treated SAE/AMS 43950 (Oct-86) Magnesium Alloy Welding Wire
9.0AI 20Zn (AZ92A)
SAE/AMS 4447E (Jan-85) Magnesium Alloy Castings, Sand
3.3Th 2.1 Zn 0 75Zr Precipitation Heat Treated SAE/AMS 4390J (Oct-91) Sheet and Plate, Magnesium
Alloy 2.0Th 0.78Mn, Solution Heat Treated, Cold
SAE/AMS 4446A (Nov-96) Magnesium Alloy, Sand Castings Worked, and Precipitation Heat Treated
8.7AI 0.70Zn 0.26Mn Solution and Precipitation Heat
Treated SAE/AMS 4389F (Jan-86) Magnesium Alloy Extrusions 3.0
Th - 1.5Mn (HM31A-TS) Precipitation Heat Treated
SAE/AMS 4445F (Jan-85) Magnesium Alloy Castings, Sand
3.3Th 0.75Zr Solution and Precipitation Heat Treated SAE/AMS 4388E (Oct-88) Magnesium Alloy Extrusions,
30Th 1.5Mn (HM31A-F), As Extruded
SAE/AMS 4444C (Jan-92) Magnesium Alloy Castings, Sand
6Zn 0.80Zr, Precipitation Heat Treated SAE/AMS 43870 (Oct-89) Magnesium Alloy Extrusions,
2.3Zn 0.62Zr, As Extruded
SAE/AMS 44430 (Jan-92) Magnesium Alloy Castings, Sand
4.5Zn 0.75Zr, Precipitation Heat Treated SAE/AMS 43868 (May-68) Magnesium Alloy Sheet and
Plate, 14Li 1.25AI*
SAE/AMS 4442E (Jan-93) Magnesium Alloy Castings, Sand
3.2Ce 2.5Zn 0.70Zr Precipitation Heat Treated SAE/AMS 4385H (Jan-92) Sheet and Plate, Magnesium
Alloy 3.2Th 0.70Zr Cold Rolled and Partially Annealed
SAE/AMS 44410 (Jul-84) Magnesium Alloy Castings, Sand
3.5Ce 0.7Zr, Solution and Precipitation Heat Treated SAE/AMS 4384G (Jan-92) Sheet and Plate, Magnesium
Alloy 3.2Th 0.70Zr, Annealed Recrystallized
SAE/AMS 44400 (Apr-84) Magnesium Alloy Castings, Sand
3.5Ce 0.7Zr, Precipitation Heat Treated SAE/AMS 43830 (Jan-92) Sheet and Plate, Magnesium
Alloy 2.0Th 0.78Mn, Solution Heat Treated, Cold
SAE/AMS 44390 (Jul-92) Magnesium Alloy Castings, Sand Worked, and Precipitation Heat Treated
4.2Zn 1.2Ce O.70Zr Precipitation Heat Treated
SAE/AMS 4382C (Oct-91) Magnesium Alloy, Plate, Extra
SAE/AMS 44380 (Apr-84) Magnesium Alloy Castings, Sand Flat 3.0AI 1.0Zn 0.20Mn, Annealed
5.7Zn 1.8Th, Precipitation Heat Treated
SAE/AMS 4381 (Jul-47) Magnesium Alloy Sheet Aluminum
SAE/AMS 44370 (Apr-90) Magnesium Alloy Castings, Zinc (Hard)*
Sand, 8.7AI 0.7Zn, Solution Heat Treated and Aged
SAE/AMS 4380A (Jul-48) Magnesium Alloy Sheet AZ51X
SAE/AMS 4434K (Jul-90) Magnesium Alloy Castings, Sand, Annealed*
90AI 2.0Zn, Solution and Precipitation Heat Treated
SAE/AMS 4377G (Oct-91) Sheet and Plate, Magnesium
SAE/AMS 4430 (Jun-50) Magnesium Alloy Castings Sand 9 Alloy 30AI 1.0Zn 0.20Mn, Cold Rolled, Partially
AI 2 Zn As Cast* Annealed
SAE/AMS 4428 (Jul-56) Magnesium Alloy Castings, Sand SAE/AMS 4376F (Oct-91) Plate, Magnesium Alloy 3.0AI
6Ce Solution and Precipitation Treated* 1.0Zn 0.20Mn, Cold Rolled and Partially Annealed
SAE MAM 4427 (Jul-92) Magnesium Alloy Sand Castings SAE/AMS 4375J (Oct-91) Sheet and Plate, Magnesium
40Y 2.3Nd 0.7Zr Solution and Precipitation Heat Alloy 3.0AI 1.0Zn 0.20Mn, Annealed and Recrystallized
Treated
SAE/AMS 4370A (Jun-62) Magnesium Alloy Sheet M1A-0
SAE/AMS 4427 (Jul-92) Magnesium Alloy Sand Castings Annealed*
4.0Y 2.3Nd 0.7Zr Solution and Precipitation Heat
Treated SAE/AMS 4363E (Jan-92) Forgings, Magnesium Alloy
20Th 0.78Mn, Precipitation Heat Treated
SAE/AMS 4426 (Apr-90) Castings, Sand, Magnesium Alloy,
5.1Y 3.0Re 0.70Zr (WE54-T6), Solution and SAE/AMS 4362E (Jan-92) Forgings, Magnesium Alloy
Precipitation Heat Treated 5.5Zn 0.45Zr Precipitation Heat Treated
SAE/AMS 44258 (Jan-92) Magnesium Alloy Castings, Sand SAE/AMS 4360E (May-68) Magnesium Alloy Forgings,
5.8Zn 2.5RE 0.70Zr, Solution and Precipitation Heat 8.5AI0.50Zn*
Treated SAE/AMS 4358A (Jul-81) Magnesium Alloy Forgings
SAE/AMS 4424K (Apr-87) Magnesium Alloy Castings, Sand AZ61X*
6.0AI 3.0Zn Solution and Precipitation Heat Treated
400 Appendix A - Standards
SAE/AMS Standards (Magnesium) - continued. BS 2TA 3 : Specification for bar & section of commercially
SAE/AMS 4352G (Jan-92) Extrusions, Magnesium Alloy pure titanium, tensile strength 390-540 MPa (obsolete)
5.5Zn OA5Zr, Precipitation Heat Treated BS 2TA 4: Specification for forging stock of commercially
SAE/AMS 4350L (Jan-92) Extrusions, Magnesium Alloy pure titanium, tensile strength 390-540 MPa (obsolete)
6.5AI 1.0Zn, As Extruded BS 2TA 5 : Specification for forgings of commercially pure
SAE/AMS 4634 (Jan-93) Aluminum Bronze Bars, Rods, and titanium, tensile strength 390-540 MPa (obsolete)
Forgings 90.5Cu 7.5AI 1.9Si Stress Relieved BS 2TA 6 : Specification for sheet & strip of commercially
SAE/AMS 4815F (Oct-86) bearings, silver plated steel back pure titanium, tensile strength 570-730 MPa
Note: * denotes that a standard has been cancelled or BS 2TA 7: Specification for bar & section for machining of
superseded as a result of technical committee action; commercially pure titanium, tensile strength 570-740
photocopies are available from SAE. MPa
BS 2TA 8: Specification for forging stock of commercially
ANSI Standards pure titanium, tensile strength 540-740 MPa (obsolete)
BS 2TA 9: Specification for forgings of commercially pure
ANSIIAWS titanium, tensile strength 540-740 MPa (obsolete)
BS 2TA 10 : Specification for sheet of Ti-AI-V alloy, tensile
ANSI/AWS A5.19-92 : Magnesium Alloy Welding Electrodes
strength 960-1270 MPa
and Rods.
BS 2TA 11 : Specification for bar & section for macining of
ANSIINFPA Ti-AI-V alloy, tensile strength 900-1160 MPa, limiting
ruling section 150 mm
ANSI/NFPA 480-1993: Storage, Handling, and Processing
BS 2TA 12 : Specification for forging stock of Ti-AI-V alloy,
of Magnesium.
tensile strength 900-1160 MPa, limiting ruling section
ANSI/NFPA 651-1993: Manufacture of Aluminum and 150 mm
Magnesium Powder.
BS 2TA 21 : Specification for sheet & strip of Ti-Cu alloy,
ANSI/SAE J tensile strength 540-700 MPa
BS 2TA 22: Specification for bar & section for machining of
ANSI/SAE J465-JUN83 : Magnesium Casting Alloys. Ti-Cu alloy, tensile strength 540-770 MPa (obsolete)
ANSI/SAE J466-JAN89 : Magnesium Wrought Alloys. BS 2TA 23 : Specification for forging stock of Ti-Cu alloy,
tensile strength 540-770 MPa (obsolete)
ANSIISAE MAM
BS 2TA 24: Specification for forgings of Ti-Cu alloy, tensile
ANSI/SAE MAM 2202A : Metric, Aluminum Alloy and strength 540-770 MPa (obsolete)
Magnesium Alloy Sheet and Plate.
BS 2TA 28: Specification for forging stock & wire ofTi-AI-V
ANSI/SAE MAM 2355B : Quality Assurance Sampling and alloy, tensile strength 1100-1300 MPa, limiting ruling
Testing of Aluminum Alloys and Magnesium Alloy. section 20 mm - primarily intended for the manufacture
of fasteners complying with BS A-series standards
TITANIUM ALLOYS BS TA 38 : Specification for bar for machining of Ti-AI-Mo-
Sn-silicon carbide alloy, tensile strength 1250-1420
MPa, limiting ruling section 25 mm
British Standards (BSI) BS TA 39 : Specification for forging stock of Ti-AI-Mo-Sn-
BS 5383 : Specification for material identification of steel, silicon carbide alloy, tensile strength 1250-1420 MPa,
limiting ruling section 25 mm
nickel alloy & titanium alloy tubes by continuous
character marking & colour-coding of steel tubes BS TA 40 : Specification for bar for machining of Ti-AI-Mo-
BS 7252-2 : Metallic materials for surgical implants. Sn-silicon carbide alloy, tensile strength 1205-1375
MPa, limiting ruling section over 25 up to & including
Specification for unalloyed titanium
75 mm
BS 7252-3 : Metallic materials for surgical implants.
Specification for wrought Ti-6AI-4V alloy BS TA 41 : Specification for forging stock of Ti-AI-Mo-Sn-
silicon carbide alloy, tensile strength 1205-1375 MPa,
BS 7252-10 : Metallic materials for surgical implants. limiting ruling section over 25 up to & including 75 mm
Specification for wrought T-5AI-2.5 Fe alloy
BS TA 42 : Specification for forgings of Ti-AI-Mo-Sn-silicon
BS 7252-11 : Metallic materials for surgical implants. carbide alloy, tensile strength 1205-1375 MPa, limiting
Specification for wrought Ti-6AI-7Nb alloy ruling section over 25 up to & including 75 mm
BS A 101 : Specification for general requirements for BS TA 43 : Specification for forging stock of Ti-AI-Zr-Mo-Si
titanium bolts alloy, tensile strength 990-1140 MPa, limiting ruling
BS A 254 to BS A 259: Specification. Hexagonal head section 65 mm (obsolete)
titanium alloy bolts, 1100 MPa BS TA 44 : Specification for forging stock of Ti-AI-Zr-Mo-Si
BS M 58 : Specification for anodic coating of titanium & alloy, tensile strength 990-1140 MPa, limiting ruling
titanium alloys by the sulphuric acid process section 65 mm (obsolete)
BS TA 45: Specification for bar & sections for machining of
BS TA Standards Ti-AI-Mo-Sn-Si alloy, tensile strength 1100-1280 MPa,
limiting ruling section 25 mm (replaces BS TA 29)
BS 2TA 1 : Specification for sheet & strip of commercially
pure titanium, tensile strength 290-420 MPa
BS 2TA 2: Specification for sheet & strip of commercially
pure titanium, tensile strength 390-540 MPa
Appendix A - Standards 401
BS TA Standards (Titanium) - Continued. DIN 65179 : Aerospace (fasteners): Titanium alloy-
BS TA 46 : Specification for bar & sections for machining of countersunk head bolts, close tolerance, with internal
Ti-AI-Mo-Sn-Si alloy, tensile strength 1050-1220 MPa, offset cruciform ribbed drive & MJ thread, short thread
limiting ruling section over 25 mm up to & including 100 length, tensile strength 1100 MPa, for temperatures up
mm (replaces BS TA 32) to 315 0 C
BS TA 47: Specification: forging stock Ti-AI-Mo-Sn-Si alloy, DIN 65197: Aerospace: Titanium & titanium alloy - round
tensile strength 1050-1220 MPa, limiting ruling section bars & wire for screw stock, dimensions, masses
100 mm (replaces BS TA30, BS TA33 & BS TA36) DIN 65289 : Aerospace (fasteners): Titanium alloy -
BS TA 48 : Specification for forgings of Ti-AI-Mo-Sn-Si alloy, countersunk head screws, ribbed TORQ-SET [ACR)
tensile strength 1050-1220 MPa, limiting ruling section recess & MJ thread, short thread length, tensile
100 mm (replaces BS TA 31, BS TA 34 & BS TA 37) strength 1100 MPa, for temperatures up to 315 0 C
BS TA 49: Specification for bar & sections for machining of DIN 65324 : Aerospace (fasteners): Titanium alloy - pan
Ti-AI-Mo-Sn-Si alloy, tensile strength 1000-1200 MPa, head bolts, close tolerance, with internal offset
limiting ruling section over 100 mm up to & including cruciform ribbed drive recess & MJ thread, short thread
150 mm (replaces BS TA 35) length, tensile strength 1100 MPa, for temperatures up
to 3150 C
BS TA 50 : Specification for forging stock of Ti-AI-Mo-Sn-Si
alloy, tensile strength 1000-1200 MPa, limiting ruling DIN 65436 : Aerospace: Titanium & titanium alloy -standard
section over 100 mm up to & including 150 mm quality [STQ] & disc quality [DQ), requirements & tests
(replaces BS TA 36) DIN 65438 : Aerospace (fasteners): Titanium alloy -
BS TA 51 : Specification for forgings of Ti-AI-Mo-Sn-Si alloy, bihexagonal head bolts, close tolerance, with MJ
tensile strength 1000-1200 MPa, limiting ruling section thread, short thread length, tensile strength 1100 MPa,
over 100 mm up to & including 150 mm (replaces BS for temperatures up to 315 0 C
TA37) DIN 65464 : Aerospace (fasteners): Titanium alloy - studs
BS TA 52 : Specification for sheet & strip of Ti-Cu alloy, with MJ thread, ring-locked, tensile strength 1100 MPa,
tensile strength 690-920 MPa for temperatures up to 315 0 C
BS TA 53 : Specification for bar & section for machining of DIN 65526 : Aerospace (fasteners): Titanium alloy -
Ti-Cu alloy, tensile strength 650-880 MPa, limiting hexagonal bolts, close tolerance, with MJ thread, short
ruling section 75 mm (obsolete) thread length, tensile strength 1100 MPa, for
temperatures up to 3150 C
BS TA 54 : Specification for forging stock of Ti-Cu alloy,
tensile strength 650-880 MPa, limiting ruling section DIN 65557 : Aerospace (fasteners): Titanium alloy - pan-
75mm (obsolete) head screws, with ribbed TORQ-SET [ACR) recess &
MJ thread, fully threaded, tensile strength 1100 MPa,
BS TA 55 : Specification for forgings of Ti-Cu alloy, tensile
for temperatures up to 315 0 C
strength 650-880MPa, limiting ruling section 75 mm
(obsolete) DIN 65558 : Aerospace (fasteners): Titanium alloy-
countersunk-head screws, with ribbed TORQ-SET
BS TA 56: Specification for plate of Ti-AI-V alloy, tensile
[ACR] recess & MJ thread, fully threaded, tensile
strength 895-1150 MPa, max. thickness 100 mm
strength 1100 MPa, for temperatures up to 315 0 C
BS TA 57 : Specification for plate of Ti-AI-Mo-Sn-Si alloy,
DIN EN 2617 (Norm-Entwurf), Publication:1996-05 :
tensile strength 1030-1220 MPa, max. thickness 65mm
Aerospace - Plate in titanium & titanium alloys;
BS TA 58 : Specification for plate of Ti-Cu alloy, tensile thickness 6 mm<a>100 mm; dimensions.
strength 520-640 MPa, max. thickness 10 mm
DIN V EN 2098-1 (Vornorm), Publication:1985-12 :
BS TA 59: Specification for sheet & strip ofTi-AI-V alloy, Aerospace series; inspection & testing requirements for
tensile strength 920-1180 MPa titanium & heat resisting alloy wrought products; part 1:
BS 2TA 100 : Procedure for inspection & testing of wrought general requirements.
titanium & titanium alloys DIN V EN 2098-2 (Vornorm), Publication:1985-12 :
Aerospace series; inspection & testing requirements for
DIN Standards titanium & heat resisting alloy wrought products; part 2:
inspection & testing requirements for sheets, strips &
DIN 1737-1 : Filler metals for welding titanium & titanium- plates.
palladium alloys, chemical compositions, technical DIN V EN 2098-3 (Vornorm), Publication:1985-12 :
delivery conditions Aerospace series; inspection & testing requirements for
DIN 17850: Titanium, chemical composition titanium & heat resisting alloy wrought products; part 3:
DIN 17851 : Titanium alloys, chemical composition inspection & testing requirements for bars & sections.
DIN 17860 : Titanium & titanium alloy plate, sheet & strip DIN V EN 2098-4 (Vornorm), Publication:1985-12:
Aerospace series; inspection & testing requirements for
DIN 17861 : Titanium & alloy seamless circular tubes
titanium & heat resisting alloy wrought products; part 4:
DIN 17863: Titanium wire inspection & testing requirements for tubes.
DIN 17865: Titanium & titanium alloy investment castings & DIN V EN 2098-5 (Vornorm), Publication:1985-12:
rammed graphite castings Aerospace series; inspection & testing requirements for
DIN 17866 : Welded circular titanium & titanium alloy tubes titanium & heat resisting alloy wrought products; part 5:
DIN 17869 : Titanium & titanium alloys, additional material inspection & testing requirements for wires.
property data
DIN 65174: Aerospace: Titanium & titanium alloy - round
bars, dimensions, masses
402 Appendix A - Standards
DIN Standards (Titanium) - continued. NF A 06-657 Decembre 1993 : Analyse chimique des
DIN V EN 2098-6 (Vornorm), Publication:1985-12 : alliages de titane. Dosage du zirconium dans les
Aerospace series; inspection & testing requirements for alliages Ti-AI-ZR. Methode gravimetrique a I'acide
titanium & heat resisting alloy wrought products; part 6: bromomandelique. Statut :Homologuee
inspection & testing requirements for bars & wires for NF A 08-650 Octobre 1992 : Analyse chimique du titane et
fasteners. alliages de titane. Dosage des elements aluminium,
LN 9297 : Aerospace: Aerospace: Titanium & titanium alloy vanadium et fer dans les alliages de nuance TA6V.
- rolled sheet & plate, dimensions. masses Methode par spectrometrie d'absorption atomique dans
la flamme ou par spectrometrie d'emission de plasma.
Statut :Homologuee
ISO Standards
NF A 08-651 Decembre 1993 : Analyse chimique du titane
ISO 5832-2: 1993 : Implants for surgery - Metallic materials - et alliages de titane. Dosage des elements en faible
Part 2: Unalloyed titanium teneur dans les alliages de nuance TA6V. Methode par
ISO 5832-3: 1996 : Implants for surgery - Metallic materials - spectrometrie d'absorption atomique dans la flam me
Part 3: Wrought titanium 6-aluminium 4-vanadium alloy ou par spectrometrie d'emission de plasma.
Statut :Homologuee
ISO 5832-10:1996: Implants for surgery - Metallic materials
- Part 10: Wrought titanium 5-aluminium 2, 5-iron alloy A 08-652 Novembre 1994 : Analyse chimique du titane et
des alliages de titane. Regles a suivre pour I'analyse
ISO 5832-11 :1994: Implants for surgery - Metallic materials par spectrometrie d'emission de plasma.
- Part 11: Wrought titanium 6-aluminium 7-niobium Statut :Fascicule de doc.
alloy
L 09-776 Octobre 1984 : Codification des references
ISO 8080: 1985 : Aerospace - Anodic treatment of titanium & relatives aux produits semi-ouvres en alliages
titanium alloys - Sulfuric acid process d'aluminium et titane, normalises, selectionnes pour les
ISOIDIS 9152 : Aerospace - Bolts, with MJ threads, in constructions aeronautiques. Statut :Fascicule de doc.
titanium alloy strength class 1100 MPa - Procurement L 14-601 Septembre 1984 : Titane et alliage de titane.
specification Barres pour forgeage en TA6V (p.q) mis en solution et
ISOIDIS 9154 : Aerospace - Bolts - Classification 1550 MPa recuit pour constructions aerospatiales
& MJ threads - Procurement specification Statut :Experimentale
ISOIDIS 9606-5 : Approval testing of welders - Fusion L 14-602 Septembre 1984 : Titane et alliage de titane.
welding - Part 5: Titanium & titanium alloys Pieces forgees en TA6V (p.q) mis en solution et recuit
pour constructions aerospatiales Statut :Experimentale
AFNOR Standards L 14-603 Septembre 1984 : Titane et alliage de titane.
Barres pour forgeage en TA6V (P.O) recuit pour
PROJET A 04-190 Avril 1997 Fonderie controle par constructions aerospatiales. Statut :Experimentale
radiographie. Projet
L 14-604 Septembre 1984 : Titane et alliage de titane.
NF L 06-383 Novembre 1987 : Assemblages soudes et Pieces forgees en TA6V (P.O) recuit pour
brases pour constructions aerospatiales. Assemblages constructions aerospatiales. Statut :Experimentale
soudes par resistance par points ou a la molette.
L 14-611 Septembre 1984 : Titane et alliage de titane.
Oualite des assemblages soudes. Statut :Homologuee
Barres pour forgeage en TA6Zr5D mis en solution et
NF A 06-650 Septembre 1992 : Analyse chimique du titane vieilli pour constructions aerospatiales.
et alliages de titane. Dosage de I'hydrog!'me. Statut :Experimentale
Statut :Homologuee
L 14-612 Septembre 1984 : Titane et alliage de titane
NF A 06-651 Septembre 1992 : Analyse chimique du titane Pieces forgees en TA6Zr5D mis en solution et vieilli
et alliages de titane. Dosage de I'oxygene. pour constructions aerospatiales. Statut :Experimentale
Statut :Homologuee
NF L 15-670 Juillet 1978 : Tubes circulaires en titane et
NF A 06-652 Decembre 1993 : Analyse chimique des alliages de titane. Statut :Homologuee
alliages de titane. Dosage de I'aluminium dans les
NF L 16-003 Mai 1991 : Industrie aeronautique. Peintures
alliages Ti-AI-V. Methode titrimetrique par I'EDTA.
et vernis. Nature et methodes de preparation de
Statut :Homologuee
surface des eprouvettes en alliages de titane.
NF A 06-653 Decembre 1993 : Analyse chimique du titane Statut :Homologuee
et alliages de titane. Dosage du fer. Methode par
spectrometrie d'absorption moleculaire.
NF L 21-270 Septembre 1981 : Rivets composites "SL" a
tige en alliage de titane T-A6V - Specification
Statut :Homologuee
technique. Statut :Homologuee
NF A 06-654 Decembre 1993 : Analyse chimique du titane
NF L 21-271 Septembre 1981 : Rivets composites "SL" a
et alliages de titane. Dosage de I'azote. Methode
tige en alliage de titane T-A6V a tete cylindrique et a
titrimetrique. Statut :Homologuee
bague en alliage 2024. Statut :Homologuee
NF A 06-655 DU 1293 Decembre 1993 : Analyse chimique
du titane et alliages de titane. Dosage du silicium.
NF L 21-272 Septembre 1981 : Rivets composites "SL" a
tige en alliage de titane T-A6V a tete fraisee 100
Methode gravimetrique. Statut :Homologuee
degres et a bague en alliage d'aluminium 2024 ..
NF A 06-656 Decembre 1993 : Analyse chimique des Statut :Homologuee
alliages de titane. Dosage du vanadium dans les
NF L 21-273 Septembre 1981 : Rivets composites "SL" a
alliages Ti-AI-V. Methode titrimetrique.
tige en alliage de titane T-A6V a tete cylindrique et a
Statut :Homologuee
bague en acier XC10, completee par I'erratum, JUln
1982. Statut :Homologuee
Appendix A - Standards 403
AFNOR NF Standards (Titanium) - continued. NF EN 2870 Novembre 1996 : Serie aerospatiale, Vis a
NF L 21-274 Septembre 1981 : Rivets composites "SL" 8 tete bihexagonale normale, tige normale 8 tolerance
tige en alliage de titane T-A6V 8 tete fraisee 100 serree, filetage court, en alliage de titane, anodisees,
degres et 8 bague en acier XC10, comphtee par lubrifiees MoS2, Classification: 1100 MPa (8
I'erratum, juin 1982 .. Statut :Homologuee temperature ambiante) I 315 degres Celsius,
Statut :Homologuee
PROJET A 89-500 Novembre 1995: Controle non destructif
des assemblages soudes regles generales. Projet NF EN 2884 Avril 1996 : Serie aerospatiale. Vis 8 tete
cylindrique, 8 empreinte cruciforme deportee, tige
PROJET A 89-510 Juillet 1994 : Controle non destructif des normale 8 tolerance large, filetage court, en alliage de
assemblages soudes examen radiographique des titane, anodisees, lubrifiees MOS2. Classification: 1100
assemblages soudes par fusion. Projet MPa (8 temperature ambiante) 1315 degres Celsius.
NF S 94-080-1 Janvier 1997: Implants chirurgicaux. Alliage Statut :Homologuee
de titane TA6V. Partie 1 : barres et billettes. NF EN 2955 Novembre 1993 : Serie aerospatiale,
Statut :Homologuee Recyciage des chutes de titane et d'alliages de titane.
NF S 94-080-2 Janvier 1997 : Implants chirurgicaux. Alliage (2e tirage corrige) Statut :Homologuee
de titane TA6V. Partie 2: toles, bandes et plaques, EN 3456PR Janvier 1994 : Serie aerospatiale, Alliage de
Statut :Homologuee titane Ti-P64001 - Recuit - Toles et bandes, laminees a
NF S 94-080-3 Janvier 1997 : Implants chirurgicaux. Alliage chaud - a inferieur ou ega I 6 mm),
de titane TA6V. Partie 3 : produits semi-finis obtenus Statut :Experimentale
par moulage, Statut :Homologuee XP EN 3851 PR Mai 1995 : Serie aerospatiale. Raccords
NF S 94-080-4 Janvier 1997 : Implants chirurgicaux, Alliage spheriques, 60 degres, en alliage de titane Ti-P64001,
de titane TA6V, Partie 4: produits semi-finis obtenus Ecrous prisonniers, droits, Statut :Experimentale
par forgeage ou par usinage, Statut :Homologuee XP EN 3852PR Mai 1995 : Serie aerospatiale, Raccords
XP S 94-081-1 Mars 1996: Implants chirurgicaux, Alliage 8 spheriques, 60 degres, en alliage de titane Ti-P64001,
base de titane, d'aluminium 6 et de niobium 7. Partie 1 Raccords droits, soudes, filetes, Statut :Experimentale
: barres et billettes, Statut :Experimentale XP EN 3853PR Mai 1995 : Serie aerospatiale, Raccords
XP S 94-081-2 Mars 1996 : Implants chirurgicaux. Alliage 8 spheriques, 60 degres, en alliage de titane Ti-P64001 ,
base de titane, d'aluminium 6 et de niobium 7, Partie 2 Raccords droits, filetes, Statut :Experimentale
: produits semi-finis obtenus par forgeage ou par XP EN 3854PR Mai 1995 : Serie aerospatiale. Raccords
usinage. Statut :Experimentale spheriques, 60 degres, en alliage de titane Ti-P64001 ,
Olives 8 souder. Statut :Experimentale
NF EN Standards XP EN 3855PR Mai 1995 : Serie aerospatiale, Raccords
NF EN 2497 Juin 1989 : Serie aerospatiale. Sablage sec du spheriques, 60 degres, en alliage de titane Ti-P64001,
titane et des alliages de titane. Statut :Homologuee Bouchons, Statut :Experimentale
NF EN 2545-1 Septembre 1995 : Serie aerospatiale. XP EN 3856PR Mai 1995 : Serie aerospatiale, Raccords
Produits pour refusion et pieces moulees en titane et spheriques, 60 degres, en alliage de titane Ti-P64001,
alliages de titane. Specification technique - Partie 1 : Ecrous prisonniers 8 jonc, StatutExperimentale
exigences generales, Statut :Homologuee XP EN 3857PR Mai 1995 : Serie aerospatiale. Raccords
NF EN 2545-2 Septembre 1995 : Serie aerospatiale. spheriques, 60 degres, en alliage de titane Ti-P64001.
Produits pour refusion et pieces moulees en titane et Raccords 8 coudes 8 90 degres, 8 souder.
alliages de titane. SpeCification technique - Partie 2 : Statut :Experimentale
produits pour refusion, Statut :Homologuee XP EN 3858PR Mai 1995 : Serie aerospatiale, Raccords
NF EN 2545-3 Septembre 1995 : Serie aerospatiale, spheriques, 60 degres, en alliage de titane Ti-P64001.
Produits pour refusion et pieces moulees en titane et Joncs en acier Fe-PA 13, Statut :Experimentale
alliages de titane, SpeCification technique - Partie 3 : EN 3859PR Janvier 1994 : Serie aerospatiale. Alliage de
pieces type et pieces de serie, Statut :Homologuee titane Ti-P19001 - Recuit - Toles et bandes, laminees 8
NF EN 2549 AoOt 1995 : Serie aerospatiale, Vis a tete chaud - a inferieur ou egal 6 mm. Statut :Experimentale
hexagonale normale, tige normale 8 tolerance serree, EN 3860PR Janvier 1994 : Serie aerospatiale. Alliage de
filetage court, en alliage de titane, anodisees, lubrifiees titane Ti-P19001 - Recuit - Toles et bandes, laminees 8
MoS2. Classification: 1100 MPa (8 temperature froid - a inferieur ou ega I 6 mm, Statut :Experimentale
ambiante)/315 degres Celsius, Statut :Homologuee XP EN 3867PR Fevrier 1995 : Serie aerospatiale.
NF EN 2858-1 AoOt 1994 : Serie aerospatiale. Titane et Raccords, brides amovibles et joints - Brides en alliage
alliages de titane - Produits destines 8 la forge, pieces de titane Ti-P64001, Statut :Experimentale
forgees et pieces matricees - Specification technique, XP EN 3868PR Fevrier 1995 : Serie aerospatiale,
Partie 1 : exigences generales, Statut :Homologuee Raccords, brides amovibles et joints - Raccords 8
NF EN 2858-2 AoOt 1994 : Serie aerospatiale. Titane et souder en alliage de titane Ti-P64001 .
alliages de titane - Produits destines 8 la forge, pieces Statut :Experimentale
forgees et pieces matricees - SpeCification technique. EN 3870PR Janvier 1994 : Serie aerospatiale, Alliage de
Partie 2 : produits destines 8 la forge, titane Ti-P19001 - Mis en solution et revenu - Toles et
Statut :Homologuee bandes, laminees 8 chaud - a inferieur ou egal 6 mm,
NF EN 2858-3 AoOt 1994 : Serie aerospatiale, Titane et Statut :Experimentale
alliages de titane - Produits destines 8 la forge, pieces EN 3871 PR Janvier 1994 : Serie aerospatiale, Alliage de
forgees et pieces matricees - SpeCification technique, titane Ti-P19001 - Mis en solution et revenu - Toles et
Partie 3 : pieces types et pieces de serie. bandes, laminees 8 froid - a inferieur ou egal 6 mm.
Statut :Homologuee Statut :Experimentale
404 Appendix A - Standards
AFNOR NF EN Standards (Titanium) - continued. EN 2529PR : Ti P11, sheet & strip, 690 :S Rm :S 920 MPa, a
XP EN 3907 PR Fevrier 1995 : Serie aerospatiale. Vis a :S 5 mm.)
tete bihexagonale, tige normale, filetage long, en EN 2530PR : Ti-P63 alloy: annealed - 900MPa :S RM :S
alliage de titane Ti-P63, revetues MoS2 - Classification 1160MPa - bars, d:S 100mm - provisional spec.)
: 1100 MPa (a temperature ambiante)/350 degres
Celsius. Statut :Experimentale EN 2531 PR : Ti-P63 alloy: annealed - 900MPa :S RM :S
1160MPa - forgings, d :S 1OOmm - provisional spec.)
XP EN 4051PR Mai 1995 : Serie aerospatiale. Raccords
spheriques, 60 degres, en alliage de titane. Logement EN 2532PR : Ti P68, bar, 1100 2: Rm 2: 1280 MPa, d :S 25
d'implantation. Statut :Experimentale mm.)
XP EN 4500-4PR Fevrier 1997 : Serie aerospatiale. EN 2533PR : Ti P68, bar, 10502: Rm 2: 1220 MPa, 25 :S d :S
Materiaux metalliques. Regles pour la redaction et la 100 mm.)
presentation des normes de materiaux. Partie 4 : EN 2534PR : Ti P68, bar, 10002: Rm 2: 1200 MPa, 100:s d
regles specifiques au titane et aux alliages de titane. :S 150 mm.)
Statut :Experimentale
EN 2545 : Titanium & titanium alloy remelting stock &
NF ISO 5838-1 Octobre 1996: Implants chirurgicaux. Fils castings. Technical specification
et broches pour os. Partie 1 : materiaux et proprietes
EN 2545-1 : General requirements
mecaniques. Statut :Homologuee
EN 2545-2 : Remelting stock
FD CR 12187 Avril 1996 : Soudage. Lignes directrices pour
un groupement des materiaux pour Ie soudage. EN 2545-3 : Preproduction & production castings
Statut :Fascicule de doc. EN 2549 AoOt 1995 : Serie aerospatiale. Vis tete a
FD CR 12361 Octobre 1996 : Essais destructifs des a
hexagonale normale, tige normale tolerance serree,
soudures sur materiaux metalliques. Reactifs pour filetage court, en alliage de titane, anodisees, lubrifiees
examen macroscopique et microscopique. MoS2. Classification: 1100 MPa (a temperature
Statut :Fascicule de doc. ambiante)/315 degres Celsius. Statut :Homologuee
EN 2617 : Aerospace - Plate in titanium & titanium alloys;
EN Standards thickness 6 mm<a>100 mm; dimensions.
EN 2858 : Titanium & titanium alloys. Forging stock &
EN 2098-1PR:1985-12 : Aerospace series; inspection & forgings. Technical specification
testing requirements for titanium & heat resisting alloy
wrought products; part 1: general requirements. EN 2858-1 : General requirements
EN 3458PR : Ti-P63 alloy: annealed - 900MPa :S RM :S EN 3860PR Janvier 1994 : Serie aerospatiale. Alliage de
1160MPa - bar & wire for machined fasteners, d :S titane Ti-P19001 - Recuit - T61es et bandes, laminees a
froid - a inferieur ou ega I 6 mm. Statut :Experimentale
25mm
EN 3867PR Fevrier 1995 : Serie aerospatiale. Raccords,
EN 3459PR : Ti P68, solution treated & aged plate, Rm :>
brides amovibles et joints - Brides en alliage de titane
1030 MPa, 6 :S a :S 50 mm.
Ti-P64001. Statut :Experimentale
EN 3462PR : Ti P11, annealed bar for machining, 540 :S Rm
EN 3868PR Fevrier 1995 : Serie aerospatiale. Raccords,
:S 770 MPa, d:S 150 mm. a
brides amovibles et joints - Raccords souder en
EN 3463PR : Ti P11, solution treated & aged bar for alliage de titane Ti-P64001. Statut :Experimentale
machining, 650 :S Rm :S 880 MPa, d :S 75 mm. EN 3870PR Janvier 1994 : Serie aerospatiale. Alliage de
EN 3464PR : Ti-P63 alloy: annealed - 900MPa :S RM :S titane Ti-P19001 - Mis en solution et revenu - T61es et
1160MPa - plate, 6mm:s a:s 100mm a
bandes, laminees chaud - a inferieur ou egal 6 mm.
Statut :Experimentale
EN 3465PR : Ti P68, Grade 2 forging stock, d :S 360 mm.
EN 3871 PR Janvier 1994 : Serie aerospatiale. Alliage de
EN 3466PR : Ti P68, solution treated & aged bar for
titane Ti-P19001 - Mis en solution et revenu - T61es et
machining, Rm:> 1000 MPa, d:S 150 mm.
a
bandes, laminees froid - a inferieur ou egal 6 mm.
EN 3494PR : Ti P11, solution treated & aged forgings, 650 :S Statut :Experimentale
Rm :S 880 MPa, d :S 75 mm. a
EN 3907 PR Fevrier 1995 : Serie aerospatiale. Vis tete
EN 3495PR : Ti P11, annealed forgings, 540 :S Rm :S 770 bihexagonale, tige normale, filetage long, en alliage de
MPa, d :S 150 mm. titane Ti-P63, revetues MoS2 - Classification: 1100
MPa (a temperature ambiante)/350 degres Celsius.
EN 3498 : Ti P99002, Annealed, Cold rolled sheet & strip,
Statut : Experimentale
390:s Rm :S 540 MPa, a :S 6 mm.
EN 4051 PR Mai 1995 : Serie aerospatiale. Raccords
EN 3499 : Ti P99003, Annealed, Cold rolled sheet & strip,
spheriques, 60 degres, en alliage de titane. Logement
570 :S Rm :S 730 MPa, a :S 6 mm.
d'implantation. Statut :Experimentale
EN 3500PR : Ti P11, annealed sheet & strip, 540 :S Rm :S EN 4500-4PR Fevrier 1997 : Serie aerospatiale. Materiaux
700 MPa, a :S 6 mm. metalliques. Regles pour la redaction et la presentation
EN 3501 PR : Ti P11, solution treated & aged sheet & strip, des normes de materiaux. Partie 4 : regles specifiques
690 :S Rm :S 920 MPa, a :S 6 mm. au titane et aux alliages de titane.
EN 3734PR : Ti P609, annealed seamless tube for pressure Statut :Experimentale
systems, Rm :s 620 MPa, 0 :s 50 mm.
EN 3735PR : Ti P609, solution treated & aged bar for
machining, Rm :> 900 MPa, d :s 75 mm.
EN 3736PR : Ti P610, solution treated & aged forgings, Rm
:> 900 MPa, d :s 75 mm.
406 Appendix A - Standards
USA MIL-STD SAE/AMS 4915G (Jul-90) Titanium Alloy, Sheet, Strip, and
Plate, 8AI 1V 1Mo, Single Annealed
MIL-T-9046J (Jan. 1983) Titanium & titanium alloy: Sheet-
SAE/AMS 4916F (Apr-90) Titanium Alloy, Sheet, Strip, and
strip - plate. Alloy designations: CP - commercially
Plate, 8AI1Mo 1V, Duplex Annealed
pure; A - alpha alloys; AB - alpha-beta alloys; B - beta
alloys. SAE/AMS 4917E (Apr-90) Titanium Alloy, Sheet, Strip, and
Plate, 13.5V 11 Cr 3.0AI, Solution Heat Treated
MIL-T-9047G (Rev. Dec. 1978) Titanium & titanium alloy:
Bars & reforge stock. Alloy designations: CP - SAE/AMS 4918H (Jun-96) Titanium Alloy, Sheet, Strip, and
commercially pure; Alpha alloys; Alpha-beta alloys; Plate 6A 1 6V 2Sn Annealed
Beta alloys. SAE/AMS 4919C (Oct-89) Titanium Alloy, Sheet, Strip, and
MIL-H-81200 Heat treatment of titanium & titanium alloys. Plate, 6AI 2Sn 4Zr 2Mo 0.08Si, Duplex Annealed
MIL-I-8950 Ultrasonic inspections SAE/AMS 4920B (May-96) Titanium Alloy, Forgings, 6AI 4V,
Alpha-Beta or Beta Processed, Annealed
MIL-STD-2154 Ultrasonic inspections.
SAE/AMS 4921G (Oct-91) Titanium Bars, Wire, Forgings,
and Rings Commercially Pure 70.0 ksi (483 MPa) Yield
AMS Strength
[See also SAE/AMS Standards] SAE/AMS 4922A (Mar-95) Titanium Alloy, Seamless
AMS 2631 Ultrasonic inspections Hydraulic Tubing, 15V 3.0Cr 3.0AI 3.0Sn Cold Worked
and PreCipitation Heat Treated
SAE/AMS 4923A (Jun-74) Titanium Alloy, Bars and
SAE Standards Forgings 2Cr 2Fe 2Mo Annealed, 120,000 psi Yield'
SAE/AMS 4913B (Invalid D) Titanium Alloy, Sheet and Strip SAE/AMS 4942C (Apr-84) Tubing, Seamless, Annealed,
4AI 3Mo 1V Solution and Precipitation Treated' 40,000 psi (275 MPa) Yield Strength
SAE/AMS 4914A (Jul-92) Titanium Alloy, Cold Rolled Sheet SAE/AMS 4943F (Jun-96) Titanium Alloy, Hydraulic,
and Strip, 15V 3AI 3Cr 3Sn Solution Heat Treated Seamless Tubing 3.0A1 2.5V Annealed
Appendix A - Standards 407
SAE/AMS Standards (Titanium) - continued. SAE/AMS 4976E (Jul-94) Titanium Alloy, Forgings, 6.0AI
SAE/AMS 4944E (Mar-95) Titanium Alloy, Seamless, 2.0Sn 4.0Zr 2.0Mo, Solution & Precipitation Heat
Hydraulic Tubing 3.0AI 2.5V Cold Worked, Stress Treated
Relieved SAE/AMS 4977C (Apr-80) Titanium Alloy, Bars 11.5Mo
SAE/AMS 4945A (Oct-92) Titanium Alloy, Tubing, 6.0Zr 4.5Sn, 1275 - 1350F (690 - 730C) Solution
Seamless, Hydraulic, 3AI2.5V, Texture Controlled, 105 Heat Treated*
ksi (724 MPa) Yield Strength Cold Worked, Stress SAE/AMS 4978C (Oct-89) Titanium Alloy, Bars, Wire,
Relieved Forgings and Rings, 6AI 6V 2Sn, Annealed
SAE/AMS 4950 (Aug-96) Titanium Alloy, Bars, Wire, SAE/AMS 4979C (Jan-92) Titanium Alloy, Bars, Forgings,
Forgings, and Rings 6.0AI 4.0V Solution Heat Treated and Rings 6A 1 6V 2Sn Solution and Precipitation Heat
and Aged Modified Strenght Treated
SAE/AMS 4951 F (Jul-90) Titanium Welding Wire, SAE/AMS 4980C (Apr-80) Titanium Alloy, Bars 11.5Mo
Commercially Pure, Environment Controlled Packaging 6.0Zr 4.5Sn, 1375F (745C) Solution Heat Treated'
SAE/AMS 4952A (Jan-96) Titanium Alloy, Welding Wire, 6AI SAE/AMS 4981 C (Jan-90) Titanium Alloy, Bars, Wire, and
2Sn 4Zr 2Mo Forgings, 6.0AI 2.0Sn 4.0Zr 6.0Mo, Solution and
SAE/AMS 4953C (Apr-90) Titanium Alloy, Welding Wire, 5AI Precipitation Heat Treated
2.5Sn SAE/AMS 4982B (Oct-93) Titanium Alloy, Wire 44.5Cb
SAE/AMS 4954F (Sep-96) Titanium Alloy, Welding Wire, SAE/AMS 4983B (Feb-95) Titanium Alloy, Forgings 10V-
6AI4V 2Fe-3AI Consumable Electrode Melted, Single-Step
SAE/AMS 49550 (Aug-96) Titanium Alloys, Welding Wire, Solution Heat Treated and Aged, 180 ksi (124 MPa)
8AI1Mo 1V Tensile Strength
SAE/AMS 4956C (Apr-90) Titanium Alloy, Welding Wire, SAE/AMS 4984A (May-95) Titanium Alloy, Forgings 10V
6A 1 4V, Extra Low Interstitials, Environment Controlled 2Fe 3AI, Consumable Electrode Melted, Solution Heat
Packaging Treated and Aged, 173 ksi (1193 MPa) Tensile
Strength
SAE/AMS 4957B (May-95) Titanium Alloy, Round Bar and
Wire, 3AI 8V 6Cr 4Mo 4Zr, Consumable Electrode SAE/AMS 4985B (Jan-97) Titanium Alloy, Investment
Melted, Solution Heat Treated and Cold Orawn Castings 6A14V, 130 UTS, 120 YS, 6% EL Hot
isostatically pressed anneal optional or when specified
SAE/AMS 4958A (Jul-89) Titanium Alloy, Bars and Rod, 3AI
8V 6Cr 4Mo 4Zr, Consumable Electrode Melted, SAE/AMS 4986A (Nov-96) Titanium Alloy, Forging 10V 2Fe
Solution Heat Treated and Centerless Ground 3AI Consumable Electrode Melted, Single Solution
Heat Treated and Overaged, 160 ksi (1103 MPa)
SAE/AMS 4959C (Oct-93) Titanium Alloy, Wire, 13.5V 11Cr Tensile Strength
3AI, Spring Temper
SAE/AMS 4987A (Oec-95) Titanium Alloy, Forgings 10V
SAE/AMS 4963 (Sep-95) Titanium Alloy, Bars, Wire, 2Fe 3AI, Consumable Electrode Melted, Single
Forgings, and Rings 6.0AI 4.0V Annealed, Heat
Solution Heat Treated and Overaged, 140 ksi (965
Treatable, Modified Strength
MPa) Tensile Strength
SAE/AMS 4965G (May-96) Titanium alloy, bars, wire, rings
SAE/AMS 4991A (Oct-87) Titanium Alloy, Castings,
and forgings, 6.0AI 4.0V Solution Heat Treated & Aged
Investment, 6AI 4V, Annealed
SAE/AMS 4966K (Jun-94) Titanium Alloy, Forgings, 5AI
SAE/AMS 4993B (Feb-94) Titanium Alloy, Blended Powder
2.5Sn, Annealed, 110 ksi (758 MPa) Yield Strength
Compacts, Sintered, 6AI 4V
SAE/AMS 4967G (Oct-93) Titanium Alloy, Bars, Wire,
SAE/AMS 4994 (Jul-92) Titanium Alloy, Powdered Metal
Forgings, and Rings 6.0AI 4.0V Annealed, Heat
Products 6AI 4V Hot Isostatically Pressed, Annealed
Treatable
SAE/AMS 4995A (Sep-77) Billets and Preforms, 5AI 2Sn
SAE/AMS 4968A (Oec-74) Titanium Alloy, Bars and
2Zr 4Cr 4Mo 0.1002, Premium Quality, Powder-
Forgings 5Zr 5AI 5Sn Annealed*
Metallurgy Product
SAE/AMS 4969 (Jun-74) Titanium Alloy, 5.4AI 1.4Cr 1.3Fe
SAE/AMS 4996A (Mar-77) Billets and Preforms, 6A14V,
1.25Mo Annealed 135,000 psi Yield* Premium Quality, Powder-Metallurgy Product
SAE/AMS 4970F (Apr-90) Titanium Alloy, Bars, Wire, and SAE/AMS 4997A (Sep-77) Titanium Alloy, Powder 5AI 2Sn
Forgings 7A 1 4Mo, Solution and Precipitation Heat
2Zr 4Cr 4Mo 0.1002, Premium Quality
Treated
SAE/AMS 4998B (Jan-93) Titanium Alloy, Powder, 6AI 4V
SAE/AMS 4971 E (Jun-96) Titanium Alloy, Bars, Wire,
Forgings, and Rings 6A 1 6V 2Sn Annealed, Heat SAE/AMS 74600 : Titanium Alloy, 6AI - 4V, Heat Treated,
Treatable Roll Threaded (AMS 4967).
SAE/AMS 49720 (Jan-90) Titanium Alloy, Bars, Wire, and SAE/AMS 7461C : Titanium Alloy, 6AI- 4V, Upset Headed,
Rings,8A1 1Mo 1V, Solution Heat Treated and Heat Treated, Roll Threaded (AMS 4967).
Stabilized SAE/AMS 74880 (R1988) : Flash Welded - Aluminum and
SAE/AMS 49730 (Oct-90) Titanium Alloy, Forgings, 8AI Aluminum Alloys.
1Mo 1V, Solution Heat Treated and Stabilized SAE/AMS 7498J : Rings, Flash Welded, Titanium and
SAE/AMS 4974C (Oct-88) Titanium Alloy, Bars and Titanium Alloys.
Forgings, 11 Sn 5.0Zr 2.3AI1.0Mo 0.21 Si, Solution and
Precipitation Heat Treated Note: denotes that a standard has been cancelled or
SAE/AMS 4975G (Jun-94) Titanium Alloy, Bars, Wire and superseded as a result of technical committee action;
Rings, 6.0AI 2.0Sn 4.0Zr 2.0Mo 0.08Si, Solution and photocopies are available from SAE.
Precipitation Heat Treated
408 Appendix A - Standards
ANSI Standards ASTM
A845-85 : Titanium Scrap for Use in Deoxidation & Alloying
ANSI/SAE AMS
of Steel
[See also: SAE AMS] B265-95a : Titanium & Titanium Alloy Strip, Sheet, & Plate
ANSI/SAE AMS 74600 : Titanium Alloy, 6AI - 4V, Heat B299 : Titanium sponge
Treated, Roll Threaded (AMS 4967).
B337 : Titanium & Titanium Alloy pipe
ANSI/SAE AMS 7461C : Titanium Alloy, 6AI - 4V, Upset
B338-95 : Seamless & Welded Titanium & Titanium Alloy
Headed, Heat Treated, Roll Threaded (AMS 4967).
Tubes for Condensers & Heat Exchangers
ANSI/SAE AMS 7498J : Rings, Flash Welded, Titanium and
B348-95a : Titanium & Titanium Alloy Bars & Billets
Titanium Alloys.
B363-95 : Seamless & Welded Unalloyed Titanium &
ANSI/AWS Titanium Alloy Welding Fittings
B367-93 : Titanium & Titanium Alloy Castings
ANSI/AWS A5.16-90 : Specification for Titanium and
Titanium Alloy Welding Electrodes and Rods. B381-95a : Titanium & Titanium Alloy Forgings
ANSI/AWS 010.6-91 : Gas Tungsten Arc Welding of B481-68(1990) : Preparation of Titanium & Titanium Alloys
Titanium Piping and Tubing, Recommended Practice. for Electroplating
B600-91 : Descaling & Cleaning Titanium & Titanium Alloy
ANSI/NFPA Surfaces
ANSI/NFPA 481-1995: Production, Processing, Handling, B817-93: Powder Metallurgy (P/M) Titanium Alloy Structural
and Storage of Titanium. Components
02651-90: Preparation of Metal Surfaces for Adhesive
ANSI/SAE ARP Bonding
ANSI/SAE ARP 1333 : Nondestructive Testing of Electron E120-96: Chemical Analysis ofTitanium & Titanium Alloys
Beam Welded Joints in Titanium-Base Alloys. E428-92 : Fabrication & Control of Steel Reference Blocks
ANSI/SAE ARP 1843A : Surface Preparation for Structural Used in Ultrasonic Inspection
Adhesive Bonding, Titanium Alloy Parts. E539-90(1996)E1 : X-Ray Emission Spectrometric Analysis
ANSI/SAE ARP 1932 : Anodize Treatment of Titanium and of 6AI-4V Titanium Alloy
Titanium Alloys, pH 12.4 Maximum. E1409-96: Determination of Oxygen in Titanium & Titanium
ANSI/SAE ARP 4146: Coiled Tubing - Titanium Alloy, Alloys by the Inert Gas Fusion Technique
Hydraulic Applications. E1447-92 : Determination of Hydrogen in Titanium &
ANSIISAE ARP 982B : Titanium Alloy Products, Wrought, Titanium Alloys by the Inert Gas Fusion Thermal
Minimizing Stress Corrosion Cracking. Conductivity Method
F67-95 : Unalloyed Titanium for Surgical Implant
ANSI/SAE AS
Applications
ANSI/SAE AS 1576B : Fittings, Welded, Hydraulic, Titanium F136-96e1 : Wrought Titanium-6 Aluminum-4 Vanadium ELI
and Corrosion Resistant Steel, 3000 psi. (Extra Low Interstitial) Alloy (R56401) for Surgical
ANSI/SAE AS 1580 : Ring, Tube Weld, 3000 psi, Hydraulic, Implant Applications
Titanium. F467-93: Nonferrous Nuts for General Use
ANSI/SAE AS 1814B: Terminology for Titanium F467M-93 : Nonferrous Nuts for General Use [Metric]
Microstructures.
F468-93 : Nonferrous Bolts, Hex Cap Screws, & Studs for
ANSI/SAE AS 4076 : Contractile Strain Ratio Testing of General Use
Titanium Hydraulic Tubing. F468M-93 : Nonferrous Bolts, Hex Cap Screws, & Studs for
ANSI/SAE AS 7460 : Bolts and Screws, Titanium Alloy 6AI - General Use [Metric]
4V Procurement, Specification for. F620-96 : Titanium 6 Aluminum-4 Vanadium ELI Alloy
ANSI/SAE AS 7461 : Bolts and Screws, Titanium Alloy 6AI - Forgings for Surgical Implants rUNS R56401]
4V Fatigue-Rated, Procurement, Specification. F945-85 : Stress-Corrosion of Titanium Alloys by Aircraft
Engine Cleaning Materials
ANSI/SAE MA
F1077-95a: Selection of Committee F-16 Fastener
ANSI/SAE MA 2060 : Fittings, Welded, Hydraulic, Titanium Specifications
and Corrosion Resistant Steel, 20,000 kPa.
F1108-97 : Ti6AI4V Alloy Castings for Surgical Implants
ANSI/SAE MA 2060A : Fittings, Welded, Hydraulic, Titanium (UNS R56406)
and Corrosion Resistant Steel, 21000 kPa.
F1295-97 : Wrought Titanium-6 Aluminum-7 Niobium Alloy
ANSI/SAE MAM for Surgical Implant Applications (UNS R56700)
F1341-92 : Unalloyed Titanium Wire for Surgical Implant
ANSI/SAE MAM 2242A : Tolerances, Metric, Corrosion and Applications
Heat Resistant Steel, Iron Alloy, Titanium,.
F1472-93 : Wrought TI-6AI-4V Alloy for Surgical Implant
ANSI/SAE MAM 2245A : Tolerances, Metric, Titanium and Applications
Titanium Alloy Extruded Bars, Rods, and Shap.
F1580-95 : Titanium & Titanium-6% Aluminum-4%
ANSI/SAE MAM 4911 : Titanium Alloy Sheet, Strip, and Vanadium Alloy Powders for Coatings of Surgical
Plate, 6AI - 4V, Annealed. Implants
Appendix A - Standards 409
BERYLLIUM
USA-MIL
MIL-B-8964 : Sheet & plate
MIL-B-21531 : Bar, rod & shape.
ASTM Standards
C 1233-93 : Determining Equivalent Boron Contents of
Nuclear Materials
03645-93 : Beryllium in Water
E439-88(1993)e1 : Chemical Analysis of Beryllium
E798-96 : Conducting Irradiations at Accelerator-Based
Neutron Sources
ANSI Standards
ANSI/SAE AMS
ANSlfSAE AMS 7900 : Virgin Beryllium Bars, Rods, and
Shapes.
ANSlfSAE AMS 7901 : Beryllium Bars, Rods, and Shapes.
ANSlfSAE AMS 7902A : Beryllium Sheet and Plate.
ANSlfSAE AMS 7903 : Beryllium Bars, Rods, Tubing, and
Shapes - 4.25BeO - 94Be, High Micro-yield S1.
ANSlfSAE AMS 7904A : Beryllium Bars, Rods, Tubing, and
Shapes - High Ductility Grade.
ANSlfSAE AMS 7905 : Beryllium Bars, Rods, Tubing, and
Shapes - Optical Grade.
ANSlfSAE AMS 7906 : Beryllium Bars, Rods, Tubing, and
Shapes - Standard Grade.
ANSlfSAE AMS 7907 : Beryllium Bars, Rods, Tubing, and
Shapes - Instrument Grade.
ANSlfSAE AMS 7908 : Beryllium Hipped Near-Net
Preforms, Standard Grade.
ANSlfSAE AMS 7910 : Beryllium Near-Performs, Standard
Grade, Cold Isostatic Pressed, Sintered.
410
Appendix B: Primary
Aluminium Production
This appendix summarises primary aluminium smelters by country, giving their location and an indication of their capacity (in
tonnes).
Argentina Brazil
Aluar Aluminio Argentino SAIC Alcan Aluminio Do Brasil SA
Puerto Madryn (175 000) Aratu, BA (58 000)
Saramenha, MG (51 000)
Australia
Alcoa Aluminio S.A
Alcan Australia Ltd. Po cos de Caldas, MG (90 000)
Kurri Kum
Alumar
Alcoa of Australia Ltd. Sao Luis, MA (330 000)
Point Henry, Geelong (185 000)
Companhia Brasileira De Aliminio
Victoria State GMT Mairinique, S.P. (215000)
(No details)
Albras - Aluminio Brasiliero S/A
First National Resource Trust Barcarena, PA (320 000)
(No details)
Valesul Aluminio SA
Citic Marubeni Aluminium Australia Pty. Ltd. Santa Cruz, R.J. (90 000)
Portland (320 000)
Cameroon
Boyne Smelters Ltd
Boyne Island (230 000) Alucam
Edea (80 000)
Comalco Ltd
Bell Bay (120 000) Canada
Tomago Aluminium Company Pty Ltd Alcan Smelters & Chemicals Ltd:
Newcastle (380 000) Jonquiere, Quebec (232 000)
Beauharnois, Quebec (48 000)
Azerbaijan Grande Baie, Quebec (180 000)
Sumgait Aluminium Smelter Isle Maligne, Quebec (73 000)
Sumgait (58 000) Kitimat, British Columbia. (272 000)
Laterriere, Quebec (204 000)
Bahrein Shawinigan, Quebec (84 000)
Appendix C
Glossary
This appendix is a compilation of terms commonly used in the light metal industry. They are a mixture of those used to
describe the materials themselves (metallurgical) and their processing, production and characteristics.
Appendix 0
Multilingual Vocabulary
Appendix E Conversion
Factors & Units
INTRODUCTION
The conversion factors listed here have been used throughout the book. Data originally supplied in a variety of metric and
imperial units has been presented in a standardised set of units based on the Systeme Intemationale d'Unites (S.I.), taking
into account the differences between UK and US quantities. Multiple units and prefixes are also given.
REFERENCE
D. R. Lide (Editor-in-Chief)
Handbook of Chemistry and Physics - A Ready-reference Book of Chemical & Physical Data
CRC Press Inc. (72nd Edition, 1991-1992)
ISBN 0-8493-0565-9
Appendix E - Conversion Factors & Units 425
CONVERSION FACTORS
BA AB
Multiply by:
A B Multiply by:
1.019716 x 10" Atmosphere (At.) Pascal (Pa, N.m-2) 98066.5
0.980665 Bar Atmosphere (At.) 1.019716
1 x 10 5 Bar Pascal (Pa, N.m-2) 1 x 105
0.577790874 BTU/(hr.ft2.oF)/ft Wattimetre.oC (W.m-1.0C-1) 1.73073
6.9334664 BTU/(hr.ft2 .oF)/in WattimetreOC (W.m-1.oC-1) 0.144228
0.0023884 Cal/sec.cm.oC Wattimetre.oC (W.m- 1.oC-1) 418.68
1000 Centipoise (cp) Pascal second (Pas) 0.001
0.03531467 Cubic foot (cu.lt) Litre (I) 28.316847
0.06102374 Cubic inch (cu.in) Cubic centimetre (cc, cm 3, ml, millilitre) 16.387064
[8 - 273.16] Degrees Centigrade (0C) Degrees Kelvin (K) [A + 273.16]
[8 x 9) / 5) + 32] Degrees Fahrenheit (OF) Degrees centigrade (OC) [A - 32) x 5) / 9]
3.2808399 Foot (ft, ') Meter (m) 0.3048
0.737561033 Foot pound (ft.lb) Joule (J) 1.35582
29.037836 Foot pound per inch (ft.lb/in) Newton metre/metre (N.m.m-1) 0.034437828
0.3937008 Inch (in, ") Centimetre (cm) 2.54
10.19716213 Kilogram centimetre (kg.cm) Newton metre (N.m) 0.0980665
10.19716213 Kilogram per square centimetre (kglcm2) Megapascal (MPa) 0.0980665
39.37008 Mil (thou, 0.001 inch) Millimetre 0.0254
1 Newton meter (Nm) Joule (J) 1
1 Newton per square millimetre (N.mm-2) Megapascal (MPa) 1
0.035273962 Ounce (oz) Gram (g) 28.349523
0.8326742 Pint {UK} Pint {USA Liq.} 1.200950
1.759754 Pint {UK} Litre (I) 0.56826125
2.113376 Pint {USA Liq.} Litre (I) 0.4731765
2.2046226 Pound (Ib) Kilogram (kg) 0.45359237
0.224809 Pound force (Ib) Newton (N) 4.44822
1 .45038 x 10-4 Pound forcelsquare inch (psi) Pascal (Pa, N.m-2) 6894.76
0.06242796 Pounds per cubic foot (lb/cu.lt) Kilograms per cubic meter (kg.m- 3) 16.01846
0.204816044 Pounds force per square foot (lb.ft2) Kilogram per square metre (kgm- 2) 4.88243
0.005710141 Pound force/linear Inch (PLI, Ib.in 1) Newton/metre (N.m- 1) 175.127
0.005710141 Pound force/linear Inch (PLI, Ib.in1) Newton/millimetre (N.mm1) 0.175127
10.76391 Square foot (sq.ft) Square meter (m2) 0.09290304
1.550003 Square inch (sq.ln) Square centimetre (sq.cm, cm2) 6.4516
0.145038 Thousand pound force/square inch (ksi) Megapascal (MPa) 6.89476
0.06474881 Tons force per square inch (tsi) Megapascal (MPa) 15.4443
1.093613298 Yard (yd) Meter (m) 0.9144
MULTIPLE UNITS
~.1354DIN(~
AA2024,161 .. _~ ,---------------,
Alloy Code or Name
Alusuisse Avional 150, 219 Type: A = aluminium, M = magnesium,
Iusuisse Avional 152, 219
~ CEN 2024, 162
DIN Wk. 3.1355 (AICuMg2), 144 Form: w
T = titanium, B = beryllium
=wrought, c =casting,
Similar alloys Hoogovens 224~, 75 p = powder
NFA,U4Gl.21j
3.2335 DIN (D) [Ac] -+ 3.3206 DIN (D) [Aw] -+ 3.3308 (AI99.9MgO.5) DIN (D) [Aw] -+
AA A3562. 262 AA 6060,190 DIN Wk. 3.330B (AI99.9MgO.5), 146
DIN GB-AISi7Mg. 283 AA 6063, 193 DIN AI 99.9 MgO.5, 211
VAW Pantal 7, 287 AA 6063A, 193 3.3315 DIN (D) [Aw]-+
3.2336 DIN (D) [Ac] -+ Alunord 6060.4B, 191 AA 5005, 174
AA 360.2, 239 Alunord 6060.79, 191 AA 5005A, 174
DIN GBD-AISi10Mg, 284 Alusuisse Anticorodal 045/0501053, 216 Alusingen 214, 150
VAW Veral Si1 OMg(D), 293 Alusuisse Extrudal-043, 221 Alusuisse Peraluman-100 (101),223
3.2341 DIN (D) [Ac] -+ Alusuisse Extrudal-050, 221 CEN 5005, 174
NF A-S4G, 256 BOAl UK AM62, 214 DIN AI Mg1, 212
VAW Pantal 5, 287 BOAl UK AM65, 214 DIN Wk. 3.3315 (AIMg1), 146
VAW Veral Si5MgA, 293 CEN 6060, 190 Hoogovens 5010,174
CEN 6063, 193
3.2342 DIN (D) [Ac] -+ DIN AI Mg SiO.3, 212
3.3316 DIN (D) [Aw]-+
DIN GB-AISi5Mg, 283 AA 5050B, 176
DIN AI Mg SiO.5, 212
VAW Veral Si5MgA, 293 DIN Wk. 3.3206 (AIMgSi05), 145 3,3317 DIN (D) [Aw] -+
3.2343 DIN (D) [Ac] -+ NF AGS, 210 AA 5657, 186
NF A-S4G, 256 Alusingen 27B, 150
3.3207 DIN (D) [Aw] -+
VAW Pantal 5, 287 Alusingen 2B9, 150
AA6101B,196
3.2371 DIN (D) [Ac] -+ Alusuisse Peraluman-B60, 225
Alusuisse Anticorodal-041, 215
AA 3560,239 Alusuisse Peraluman-B63, 225
3.3208 (AI99.9MgSi) DIN (D) [Aw] -+ CEN 5657, 186
AA 3570,239 DIN Wk. 3.320B (AI999MgSi), 145
AA A356.2, 262 DIN AI 99.B5 Mg1, 211
DIN AI 99.9 Mg Si, 211
VAW Pantal 7, 287 3.3318 DIN (D) [Aw] -+
3.3210 DIN (D) [Aw]-+ DIN AI 99.9 Mg1, 211
3.2373 DIN (D) [Ac] -+ AA 6005A, 188
AA 359.2, 239 3,3326 DIN (D) [Aw] -+
Alunord 6005A, 188
VAW Silumin-Beta, 288 AA 5051A, 176
Alusuisse Anticorodal 062, 216
3,2381 DIN (D) [Ac] -+ CEN 5051A, 176
CEN 6005A, 189
VAW Veral Si1 OMgA, 293 DIN AI Mg1 ,B, 212
DIN AI Mg SiO.7, 213
DIN Wk. 3,3326 (AIMg1B), 146
3.2382 DIN (D) [Ac] -+ NF A-SGO.5, 218
Hoogovens5020,175
AA 360.2. 239 3.3211 DIN (D) [Aw] -+
VAW Veral Si1 OMg(D), 293 3,3504 DIN (D) [Mc] -+
AA 6061, 191
BS MAG-S-111 0, 308
3.2383 DIN (D) [Ac]-+ Alusuisse Anticorodal OBO, 216
NF G-A3Z1, 306
AA 361.1,239 Alusuisse Anticorodal-OB2, 216
VAW Veral 233, 290 CEN 6061, 192 3.3504 DIN (D) [Mw] -+
DIN Wk. 3.3211 (AIMg1 SiCu), 145 ASTM AZ31 B, 301
3.2521 DIN (D) [Ac] -+ DIN 3.5312, 297
DIN GB-AISi12, 283 Hoogovens 6560, 198
Reynolds R-2000, 227 3.3523 DIN (D) [Aw]-+
3.2523 DIN (D) [Ac] -+ AA 5052, 177
DIN GB-AISi12(Cu), 283 3.3214 DIN (D) [Aw] -+
AA 6061, 191 Alusuisse Peraluman 253, 224
VAW Veral 231A, 290 CEN 5052, 177
Alusuisse Anticorodal OBO, 216
3.2581 DIN (D) [Ac] -+ DIN Wk. 3.3523 (AIMg2,5), 146
Alusuisse Anticorodal-OB2, 216
AA A413.2, 263 Hoogovens 5520, 185
CEN 6061, 192
VAW Veral Si12A, 293 VAW 63/52, 148
DIN Wk. 3.3211 (AIMg1 SiCu), 145
3.2582 DIN (D) [Ac] -+ Hoogovens 6560, 198 3.3525 DIN (D) [Aw] -+
AAA413.1,263 Reynolds R-2000, 227 AA5251,182
AA A413.2, 263 CEN 5251, 183
3,3241 DIN (D) [Ac] -+
VAW Veral Si12A(D), 293 DIN Wk. 3.3526 (AIMg2MnO.3), 146
AA 512.2,242
VAW Veral Si12A, 293 3,3527 DIN (D) [Aw] -+
VAW Veral Mg3Si(H), 292
3.2583 DIN (D) [Ac] -+ AA 5049,176
3.3242 DIN (D) [Ac] -+
VAW Veral 231A, 290 Hoogovens 3010, 168
AA 512.2,242
3.2586 DIN (D) [Ac] -+ DIN GB-AIMg3Si, 282 3.3535 DIN (D) [Aw] -+
AAA413.1,263 VAW Veral Mg3Si(H), 292 AA5154,181
DIN GBD-AISi12, 284 AA 5154A, 181
3.3261 DIN (D) [Ac] -+
VAW Veral Si12A(D), 293 AA 5254, 183
VAW Veral Mg5Si(H), 292
3.2982 DIN (D) [Ac] -+ AA 5754, 187
3.3262 DIN (D) [Ac]-+ Alusingen 234, 150
AAA413.1,263
DIN GB-AIMg5Si, 283 Alusuisse Peraluman-300 (301), 224
VAW Veral 231 (D), 290
VAW Veral Mg5Si(H), 292 Alusuisse Peraluman-302, 224
3,2985 DIN (D) [Ac] -+
3,3292 DIN (D) [Ac] -+ CEN 5154A, 181
AAA413.1,263
AA 51B.0, 243 CEN 5754, 187
DIN GBD-AISi12(Cu), 284
AA 51B.1, 243 DIN AI Mg3 EO, 212
VAW Veral 231 (D), 290
AA 51B.2, 243 DIN AIMg3.5, 212
AA 5350,243 DIN Wk. 3,3535 (AIMg3), 147
VAW Veral Mg9(H), 292 Hoogovens 5030, 175
VAW Veral Mg9, 292 NF A-G3, 210
3.3293 DIN (D) [Ac] -+ 3.3537 DIN (D) [Aw] -+
AA51B.1,243 AA 5454, 184
AA 51B.2, 243 Alusuisse Peraluman-260, 224
DIN GBD-AIMg9, 284 CEN 5454, 185
VAW Veral Mg9(H), 292 Hoogovens 5400, 184
VAW Veral Mg9, 292 3.3541 DIN (D) [Ac]-+
3.3307 DIN (D) [Aw] -+ AA 514,2,243
DIN AI 99.95 MgO.5, 211 VAW Veral Mg3(H), 291
VAW Veral Mg3, 291
Alloy Cross-Reference Listing 431
3.3542 DIN (D) [Ae] ... 3.4364 DIN (D) [Aw] ... 3.5315 DIN (D) [Mw] ...
AA 514.2,243 AA 7075,203 Comeca AZ31 B, 301
DIN GB-AIMg3, 282 Alusuisse Perunal215, 226 Magnesium Elektron AZ31, 300
VAW Veral Mg3(H), 291 CEN 7075, 204 3.5470 DIN (D) [Me] ...
VAW Veral Mg3, 291 DIN Wk. 3.4365 (AIZnMgCu1.S), 147 ASTMAS41A,300
3.3545 DIN (D) [Aw] ... Hoogovens 7750, 207
3.5612 DIN (D) [Mw]'"
AA 5086,179 3.4365 DIN (D) [Aw] ... AECMA MG-P-63, 311
Alusuisse Peraluman-41 0/412, 224 AA 7075,203 ASTM AZ61A, 301
CEN 5086, 180 Alusuisse Perunal 215, 226 BS MAG-E-121M, 308
Hoogovens 5503, 185 CEN 7075, 204 DIN 3.5612, 297
NF A-G4MC, 210 DIN Wk. 3.4365 (AIZnMgCu1.5), 147 Magnesium Elecktron AZ61, 301
3.3547 DIN (D) [Aw] ... Hoogovens 7750, 207 NF G-A6Z1, 306
AA 5083,178 3.4384 DIN (D) [Aw] ... 3.5662 DIN (D) [Me] ...
Alusuisse Peraluman-460/462, 225 AA 7475,206 ASTM AM60A, 299
Alusuisse Peraluman-462, 225 CEN 747S, 207 3.5714 DIN (D) [Mw] ...
CEN 5083, 179 3.4394 DIN (D) [Aw] ... ASTM AZ80F, 302
Hoogovens 5510, 185 AA 7010,199
Superform Metals 5083 SPF, 179 3.5812 DIN (D) [Me]'"
Alusuisse Contal, 220
AECMA MG-C-61, 311
3.3549 DIN (D) [Aw] ... CEN 7010, 199 ASTM AZ81A, 302
AA 5182, 181 3.5101 DIN (D) [Me]'" BS MAG 1, 309
CEN 5182, 182 AECMA MG-C-43, 311 BS MAG2, 309
VAW 63/45, 148 ASTM ZE41A, 314 BS MAG3, 309
3.3555 DIN (D) [Aw] ... BS MAGS, 310 DIN Wk. 3.5812, 297
AA 5019, 175 DIN Wk. 3.5101, 297 NF G-A9, 306
AA 5056,177 Magnesium Elektron ZE41, 305
3.5812 DIN (D) [Mw]'"
AA 5056A, 178 NF G-Z4TR, 306
ASTM AZ80A, 302
AA 5356,184 3.5102 DIN (D) [Me]'" ASTM AZ80F, 302
AA 5456,185 ASTM ZHS2A, 314 BS2L121, 297
CEN 5019, 175 BS MAG9, 310 CEN MG-P-61, 311
CEN 5356, 184
3.5103 DIN (D) [Me]'" DIN 3.5812, 297
CEN 5456A, 185
AECMA MG-C-91, 311 Magnesium Elektron AZ80, 302
DIN Wk. 3.3555 (AIMg5), 147
ASTM EZ33A, 306 NF G-A7Z1, 306
3.3561 DIN (D) [Ae] ... BS MAG6, 310 NF G-A8Z, 306
AA 535.2, 243 DIN Wk. 3.5103, 297 3.5912 DIN (D) [Me] ...
VAW Veral Mg5(H), 292 Magnesium Elektron EZ33, 304 ASTM AZ91A, 303
3.3562 DIN (D) [Ae] ... 3.5105 DIN (D) [Me] ... ASTM AZ91 B, 303
AA 535.2, 243 ASTM HZ32A, 307 ASTM AZ91D, 303
DIN GB-AIMg5, 283 BS MAG8, 310 ASTM AZ91 E, 303
VAW Veral Mg5(H), 292 BS MAG7, 310
3.5106 DIN (D) [Me] ...
3.3585 DIN (D) [Aw] ... ASTM QE22A, 312 DIN Wk. 3.5912, 297
AA 5454, 184 BS MAG13, 310 NF G-A9Z1, 306
Alusuisse Peraluman-260, 224 Magnesium Elektron QE22, 304 3.6104 DIN (D) [Me]'"
CEN 5454, 185 AECMA MG-C-43, 311
3.5112 DIN (D) [Mw]'"
Hoogovens 5400, 184 ASTM ZE41A, 314
ASTM AZ31C, 301
3.3591 DIN (D) [Ae] ... BS MAG5, 310
3.5114 DIN (D) [Me]'"
AA 5200,243 ASTM ZH62A, 314 DIN Wk. 3.5101, 297
3.4144 DIN (D) [Aw] ... Magnesium Elektron ZE41 , 305
BS MAG9, 310
AA 7050,202 NF G-Z4TR. 306
3.5161 DIN (D) [Me]'"
AA 7150,205 3.6204 DIN (D) [Me] ...
ASTM ZK61A, 315
CEN 7050, 202 ASTM ZKSOA, 315 AECMA MG-C-91, 311
3.4334 DIN (D) [Aw] ... ASTM EZ33A, 306
BS MAG-x-161, 309
AA 7175,205 BS MAG6, 310
DIN Wk. 3.5161, 297
CEN 7175, 206 DIN Wk. 3.5103, 297
NF G-Z5Zr, 306
Magnesium Elektron EZ33, 304
3.4335 DIN (D) [Aw] ... 3.5164 DIN (D) [Me]'"
AA 7020,200 3.6254 DIN (D) [Me] ...
ASTM QE22A, 312
Alusuisse Unidur 102, 229 ASTM HZ32A, 307
BS MAG13, 310
CEN 7020, 200 BS MAG8, 310
Magnesium Elektron QE22, 304
DIN AI Zn4.5 Mg1, 214 3.7024 DIN (D) [Tw] ...
3.5194 DIN (D) [Me]'"
DIN Wk. 3.4335 (AIZn4.5Mg1), 147 BS 2TA1, 317
ASTM AZ91 C, 303
Hoogovens 7350, 206 CEN Ti P99001, 341
ASTM AZ91D, 303
3.4344 DIN (D) [Aw] ... Deutsche Titan Tikrutan RT 12, 342
BS MAG3, 309
AA 7022,201 DIN Wk. 3.7025, 318
DIN Wk. 3.5912, 297
AA 7079, 204, 205 Timetal 35A, 322
NF G-A9Z1, 306
Alusuisse Certal, 220 RIMA AZ91 C, 303 3.7025 DIN (D) [Tw] ...
Alusuisse Perunal 205, 226 ASTM Grade 1, 332
3.5200 DIN (D) [Mw] ...
Hoogovens 7790, 207 Deutsche Titan Tikrutan RT 12, 342
ASTM MIA, 312
3.4345 DIN (D) [Aw] ... Teledyne Allvac 30, 329
3.5312 DIN (D) [Me] ... Titanium Industries GR-1, 331
AA 7022,201
BS MAG-S-1110, 308 Titanium IntI. Ti-1, 337
AA 7079, 204, 205
NF G-A3Z1, 306
Alusuisse Certal, 220 3.7034 DIN (D) [Te] ...
Alusuisse Perunal 205, 226 3.5312 DIN (D) [Mw]'" NF T 40,336
Hoogovens 7790, 207 ASTMAZ31B,301
Comeea AZ31B, 301 3.7034 DIN (D) [Tew]'"
3.4354 DIN (D) [Aw] ... Timetal SOA, 323
DIN 3.5312, 297
AA 7009,199
Magnesium Elektron AZ31, 300
432 Alloy Cross-Reference Listing
3.7034 DIN (D) [Tw]-+ 3.7154 DIN (D) [Tw]-+ 3.7255 DIN (D) [Tw]-+
ASTM Grade 2. 332 Deutsche Titan Tikrutan LT 26, 341 Deutsche Titan Tikrutan RT 18 Pd, 343
CEN Ti P99002. 341 DIN Wk. 3.7155, 319 3AI-2.5V ASTM (USA) [Tw] -+
Deutsche Titan Tikrutan RT 15. 343 IM1685,325 ASTM Grade 9, 333
DIN Wk. 3.7035, 318 NF T-A6Zr5D, 337 Timetal 3-2.5, 318
3.7035 DIN (D) [Te] -+ Timetal 685, 325
3144 (UK) [Aw] -+
NF T 40,336 3.7155 DIN (D) [Tw]-+ AA 5050,176
3.7035 DIN (D) [Tew] -+ Deutsche Titan Tikrutan LT 26, 341 Alusuisse Peraluman 150/151, 223
Timetal 50A, 323 DIN Wk. 3.7155, 319 CEN 5050, 176
Titanium Industries GR-2, 331 3.7164 DIN (D) [Tew] -+ 3158 (UK) [Aw] -+
3.7035 DIN (D) [Tw] -+ NF TA6V, 336 AA 5019, 175
ASTM Grade 2, 332 Timetal 6-4, 321 AA 5056, 177
Deutsche Titan Tikrutan RT 15, 343 3.7164 DIN (D) [Tw]-+ AA 5356, 184
Teledyne Allvac 40, 329 AMS 4905, 326 CEN 5019, 175
Titanium IntI. Ti-2, 337 ASTM Grade 5, 333 CEN 5356, 184
3.7055 DIN (D) [Tew] -+ BS 2TA10, 317 3L63 (UK) [Aw] -+
Timetal 65A, 323 CEN Ti P63, 340 AA 2014,159
Titanium Industries GR-3, 331 Deutsche Titan Tikrutan LT 31, 342 AA 2014A, 160
3.7055 DIN (D) [Tw]-+ DIN LW. 3.7164, 319 Alusuisse Avional-660/662, 219
DIN Ti AI6 V4, 339 CEN 2014, 160
ASTM Grade 3, 332
Deutsche Titan Tikrutan RT 18, 343 DIN Wk. 3.7165, 320 Hoogovens 2140, 164
DTD 5163,328
DIN Wk. 3.7055, 318 3L80 (UK) [Aw] -+
Titanium IntI. Ti-3, 337 NF Ti P64001 , 340
AA 5251,182
Teledyne Allvac 6-4, 329
3.7064 DIN (D) [Tew] -+ Alusuisse Peraluman-226, 223
3.7165 DIN (D) [Tew] -+ CEN 5251, 183
ASTM Grade 4, 333
Timetal 100A, 323 NF TA6V, 336 DIN Wk. 3.3526 (AIMg2MnO.3), 146
Timetal 6-4, 321
3.7064 DIN (D) [Tw]-+ 3181 (UK) [Aw] -+
Titanium Industries GR-5, 331
ASTM Grade 4, 332 AA 5251,182
CEN Ti P99003, 341 3.7165 DIN (D) [Tw]-+ Alusuisse Peraluman-226, 223
AMS 4905, 326 CEN 5251, 183
Deutsche Titan Tikrutan RT 20, 343
ASTM Grade 5, 333 DIN Wk. 3.3526 (AIMg2MnO.3), 146
DIN Wk. 3.7065, 318
BS 2TA10, 317
Teledyne Allvac 55, 329 3186 (UK) [Aw] -+
CEN Ti P63, 340
Timetal 75A, 323 DIN Wk. 3.1305 (AICu2.5MgO.5), 144
Deutsche Titan Tikrutan LT 31, 342
3.7065 DIN (D) [Tew] -+ DIN LW. 3.7164, 319 31122 (UK) [Me]-+
ASTM Grade 4, 333 DIN Ti AI6 V4, 339 AECMA MG-C-61, 311
Timetal 100A, 323 DIN Wk. 3.7165, 320 ASTM AZ81A, 302
Titanium Industries GR-4, 331 DTD 5163, 328 BS MAG1, 309
3.7065 DIN (D) [Tw]-+ NF Ti P64001, 340 BS MAG2, 309
ASTM Grade 4, 332 Titanium IntI. Ti-64, 339 DIN Wk. 3.5812, 297
CEN Ti P99003, 341 NF G-A9, 306
3.7174 DIN (D) [Tw]-+
Deutsche Titan Tikrutan RT 20, 343 AMS 4918,327 31124 (UK) [Me]-+
DIN Wk. 3.7065, 318 Deutsche Titan Tikrutan LT 33, 342 ASTM AZ91 C, 303
Teledyne Allvac 70, 329 ASTM AZ91 D, 303
DIN LW 3.7174, 320
Timetal 75A, 323 BS MAG3, 309
DIN Wk. 3.7175, 320
Titanium IntI. Ti-4, 337 Timetal 6-6-2, 321 DIN Wk. 3.5912, 297
3.7105 DIN (D) [Tew]-+ NF G-A9Z1, 306
3.7175 DIN (D) [Tw]-+ RIMA AZ91 C, 303
Deutsche Titan Tikrutan LT 27, 342 AMS 4918,327
3.7110 DIN (D) [Tw]-+ Deutsche Titan Tikrutan LT 33, 342 3L125 (UK) [Me]-+
Deutsche Titan Tikrutan LT 35, 342 ASTM AZ91 C, 303
DIN Wk. 3.7175, 320
ASTM AZ91 D, 303
3.7114 DIN (D) [Tw]-+ 3.7184 DIN (D) [Tw]-+ BS MAG3, 309
Teledyne Allvac 6-2-4-2, 328 BS TA45, 337 DIN Wk. 3.5912, 297
3.7115 DIN (D) [Tw]-+ Deutsche Titan Tikrutan LT 34, 342 NF G-A9Z1, 306
AMS 4910,327 DIN LW 3.7184,320 RIMA AZ91 C, 303
AMS 4926, 328 DIN Wk. 3.7185, 320
NF TA 4DE, 336 4AI 4Mn SAE (USA) [Tw] -+
DIN Wk. 3.7115, 318
AECMA Ti P62, 340
3.7124 DIN (D) [Tw]-+ Timetal 550, 324
ASTM 17,321
AECMA Ti P9001 , 340 3.7185 DIN (D) [Tw]-+ ASTM F7, 331
BS 2TA21 , 317 Deutsche Titan Tikrutan LT 34, 342 Crucible Steel Co. C130AM, 330
Deutsche Titan Tikrutan LT 25, 341 DIN LW 3.7184,320 DTD 5053, 328
DIN LW 3.7124,319 DIN Wk. 3.7185, 320 IMI 314A, 324
NF T-U2, 344 3.7194 DIN (D) [Tw]-+ NF TA 5M, 336
Timetal230, 324 ASTM 3AI-2.5V, 321 4134 (UK) [Aw] -+
3.7134 DIN (D) [Tw]-+ ASTM Grade 9, 333 AA 1200,156
Teledyne Allvac 8-1-1 , 329 Timetal 3-2.5, 318 Alusuisse Pure Aluminium 99.0, 226
3.7144 DIN (D) [Tw]-+ 3.7195 DIN (D) [Tw]-+ CEN 1200, 156
Deutsche Titan Tikrutan LT 24,341 ASTM 3AI-2.5V, 321 DIN AI 99, 210
DIN Wk. 3.7145, 319 ASTM Grade 9,333 Hoogovens 1010, 151
Teledyne Allvac 6-2-4-6, 329 Timetal 3-2.5, 318 Lawson Mardon (LM) Star 1201, 156
3.7145 DIN (D) [Tw] -+ 3.7225 DIN (D) [Tw]-+ VAW 99/00, 149
Deutsche Titan Tikrutan LT 24, 341 ASTM Grade 11, 333 SAl 2.5Sn SAE (USA) [Tew] -+
Teledyne Allvac 6-6-2, 329 Deutsche Titan Tikrutan RT 12 Pd, 343 3620-TA7, 326
3.7235 DIN (D) [Tw]-+
ASTM Grade 7, 333
Deutsche Titan Tikrutan RT 15 Pd, 343
Alloy Cross-Reference Listing 433
5AI 2.5Sn SAE (USA) [Tw] -+ 14,4017 (S) [Aw]-+ 14,4425 (S) [Aw] -+
AMS 4910, 327 AA 1050, 151 AA 7005, 199
AMS 4926, 328 Hoogovens 1000, 151 AA 7020,200
ASTM Grade 6, 333 VAW 99/52, 149 Alusuisse Unidur 102, 229
DIN Wk. 3.7115, 318 14,4020 (S) [Aw] -+ CEN 7020, 200
DTD 5083, 328 AA 1060, 152 DIN AI Zn4.5 Mg1, 214
NF TA 5E, 336 Lawson Mardon (LM) Star 1602, 158 DIN Wk. 3A335 (AIZn4.5Mg1), 147
5L36 (UK) [Aw] -+ 14,4022 (S) [Aw] -+
Hoogovens 7350, 206
AA 1050A, 152 AA 1350, 157 25 SAE (USA) [Aw] -+
Alusingen 134, 149 Alusuisse Pure Aluminium 99.5 E, 227 AA 1100,154
Alusuisse Pure Aluminium 99.5, 227 CEN 1350, 157 CEN 1100, 154
CEN 1050A, 152 Hoogovens 1001,151 28 SAE (USA) [Aw] -+
14,4102 (S) [Aw] -+
DIN AI 99.5, 210 AA 1230, 156
DIN Wk. 3.0255 (AI99.5), 143 AA 6101A, 196 29 SAE (USA) [Aw] -+
NF A-5, 210 AA 6463, 198 AA 3003, 166
NF A-5L, 210
DIN AI 99.85 Mg Si, 211 Alusuisse Aluman 100, 213
5L37 (UK) [Aw] -+ DIN AI 99.85 Mg SiOA, 211 CEN 3003, 167
AA 2017, 160 DIN Wk. 3.2305 (AIMgSi), 145 Hoogovens 3530, 170
Hoogovens 2170, 164 Lawson Mardon (LM) Star 3103, 169
14,4104 (S) [Aw]-+
5L44 (UK) [Aw] -+ AA 6063, 193 NF 3003, 167
AA 5251, 182 CEN 6063, 193 Reynolds Tread-Brite, 228
Alusuisse Peraluman-226, 223 DIN AI Mg SiO.5, 212 VAW41/20,148
CEN 5251, 183
14,4120 (S) [Aw]-+ 30 DIN (D) [Tw] -+
DIN Wk. 3.3526 (AIMg2MnO.3), 146 Titanium IntI. Ti-1, 337
AA 5052, 177
6-2-4-2 (Prop.) [Tw] -+ Alusuisse Peraluman 253, 224 35 DIN (D) [Tw] -+
Ti-6242, 339 CEN 5052, 177 Titanium IntI. Ti-2, 337
6-2-4-6 (Prop) [Tw] -+ DIN Wk. 3.3523 (AIMg2.5), 146 35D DIN (D) [Tw] -+
Timetal 6-2-4-6, 321 Hoogovens 5520, 185 Titanium IntI. Ti-3, 337
6L 16 (UK) [Aw] -+ VAW 63/52, 148
40E Old AA (USA) [Ac] -+
AA 1200,156 14,4125 (S) [Aw]-+ AA 712.0,244
Alusuisse Pure Aluminium 99.0, 226 AA 5754, 187 AA 712.2, 244
Alusingen 234, 150
43 Old AA (USA) [Ac] -+
CEN 1200, 156
DIN AI 99, 210 Alusuisse Peraluman-300 (301), 224
AA 443.0,242
Hoogovens 1010, 151 Alusuisse Peraluman-302, 224
AA 443.1, 242
Lawson Mardon (LM) Star 1201, 156 CEN 5754, 187
AA 443.2, 242
VAW 99/00, 149 DIN AI Mg3 EO, 212
43 (0,15 Cu max.) Old AA (USA) [Ac]-+
6L 17 (UK) [Aw] -+ DIN Wk. 3.3535 (AIMg3), 147
Hoogovens 5030, 175 AA B443.0, 277
AA 1200, 156
NF A-G3, 210 AA B443.1, 277
Alusuisse Pure Aluminium 99.0, 226
CEN 1200,156 14,4133 (S) [Aw]-+ 43 (0.30 Cu max.) Old AA (USA) [Ac] -+
DIN AI 99, 210 AA5154,181 AA A443.0, 264
Hoogovens 1010, 151 DIN AIMg3.5, 212 AA A443.1, 264
Lawson Mardon (LM) Star 1201. 156 14,4140 (S) [Aw] -+ 52 SAE (USA) [Mw] -+
VAW 99/00, 149 AA 5083, 178 ASTM AZ31 B, 301
6L25 (UK) [Aw] -+ Alusuisse Peraluman-460/462, 225 Comeca AZ31 B, 301
AA 2218,164 Alusuisse Peraluman-462, 225 Magnesium Elektron AZ31, 300
17 ASTM (USA) [Tw] -+ CEN 5083, 179 55 DIN (D) [Tw] -+
ASTM 17,321 Hoogovens 5510, 185 Titanium IntI. Ti-4, 337
ASTM F7, 331 Superform Metals 5083 SPF, 179 88C (UK) [Mw] -+
Crucible Steel Co. C130AM, 330 14,4146 (S) [Aw]-+ ASTM AZ80A, 302
DTD 5053, 328 AA 5056, 177 91 E - BS (UK) [Aw] -+
IMI 314A, 324 14,4212 (S) [Aw]-+ AA 61 01A, 196
NF TA 5M, 336 AA 6082,194 CEN 6101, 196
7L37 (UK) [Aw] -+ Alusuisse Anticorodal 110/112, 217 DIN Wk. 3.2305 (AIMgSi), 145
AA 2014, 159 Alusuisse Anticorodal112/114, 217 142 Old AA (USA) [Ac]-+
AA 2014A 160 Alusuisse Anticorodal-1 00/1 05, 216 AA 242.0, 235
Alusuisse Avional-660/662, 219 BOAL UKAM68, 215 AA 242.1, 235
CEN 2014, 160 CEN 6082, 195 AA 242.2, 235
Hoogovens 2140, 164 DIN AI Mg Si1, 213 150.1 AA (USA) [Ac]-+
8-1-1 (Prop) [Tw] -+ DIN Wk. 3.2315 (AIMgSi1), 145 AA 150.1, 233
Ti-8AI-1Mo-1V,338 Hoogovens 6010, 189 VAW Veral 99.5, 289
NF A-SGM07, 218
10-2-3 (Prop) [Tw]-+ 170.1 AA (USA) [Ac]-+
Timetal 10-2-3, 322 14,4338 (S) [Aw] -+ AA 170.1, 233
AA 2014, 159
13 Old AA (USA) [Ac] -+ AA 2014A, 160
VAW Veral 99.7, 289
AA413.0,241 195 Old AA (USA) [Ac]-+
Alusuisse Avional-660/662, 219
AA413.1,241 AA 295.0, 235
CEN 2014, 160
14,4010 (S) [Aw]-+ AA 295.1 , 235
DIN Wk. 3.1255 (AICuSiMn), 144
AA 1200, 156 AA 295.2, 235
Hoogovens 2140, 164
Alusuisse Pure Aluminium 99.0, 226 201.0 A AA (USA) [Ac] -+
CEN 1200, 156 AA A201.0, 261
DIN AI 99, 210 AAA201.1,261
Hoogovens 1010, 151 203.0 AA (USA) [Ac] -+
Lawson Mardon (LM) Star 1201, 156 AA 203.0, 233
VAW 99/00, 149
203,2 AA (USA) [Ac] -+
VAW 99/01, 149
AA 2032,233
434 Alloy Cross-Reference Listing
204.0 AA (USA) [Ac] -+ 245 DIN (D) [Ac] -+ 354 Old AA (USA) [Ac) -+
AA 204.0, 234 DIN GB-AIMg5Si, 283 AA 3540,238
204.2 AA (USA) [Ac] -+ 295.0 AA (USA) [Ac] -+ AA 354.1, 238
AA 204.2, 234 AA 295.0, 235 354.0 AA (USA) [Ac] -+
VAW Veral Cu4TiMg, 291 295.1 AA (USA) [Ac]-+ AA 3540,238
206.2 A AA (USA) [Ac] -+ AA 295.1, 235 354.1 AA (USA) [Ac] -+
AA A206.2, 261 295.2 AA (USA) [Ac] -+ AA 354.1, 238
214 Old AA (USA) [Ac] -+ AA 295.2, 235 355 Old AA (USA) [Ac] -+
AA 514.0, 243 296.0 AA (USA) [Ac] -+ AA 3550,238
AA514.1, 243 AA 2960,235 AA 355.1, 238
AA 514.2,243 AA 355.2, 238
296.1 AA (USA) [Ac]-+
214 SAE (USA) [Aw] -+ AA 296.1 , 235 355.0 AA (USA) [Ac] -+
AA 7020,200
296.2 AA (USA) [Ac] -+ AA 3550,238
Alusuisse Unldur 102,229
AA 296.2. 236 355.0 C AA (USA) [Ac] -+
CEN 7020, 200
DIN AI Zn4.5 Mg1, 214 30B.0 AA (USA) [Ac] -+ AA C355 0, 277
DIN Wk. 3.4335 (AIZn4.5Mg1), 147 AA 3080,236 355.1 AA (USA) [Ac) -+
30B.1 AA (USA) [Ac]-+ AA 355.1 , 238
Hoogovens 7350, 206
218 Old AA (USA) [Ac]-+ AA 308.1 , 236 355.2 AA (USA) [Ac] -+
AA 518.0,243 30B.2 AA (USA) [Ac] -+ AA 355.2, 238
AA518.1,243 AA 308.2, 236 AA C355.2, 277
AA 518.2,243 314A (Prop.) [Tw]-+ 356 Old AA (USA) [Ac] -+
AA 520.0, 243 AECMA Ti P62, 340 AA 3560,239
AA 520.2, 243 ASTM 17,321 AA 356.1,239
AA 356.2, 239
224 Old AA (USA) [Ac] -+ ASTM F7. 331
VAW Veral Cu4Ti, 291 Crucible Steel Co. C 130AM, 330 356.0 AA (USA) [Ac) -+
AA 356.0, 239
225 DIN (D) [Ac] -+ DTD 5053, 328
DIN GB-AISi6Cu4, 283 IMI 314A, 324 356.0 A AA (USA) [Ac] -+
NF TA 5M, 336 AA A356 0, 262
226 DIN (D) [Ac] -+
DIN GBD-AISi9Cu3. 284 31BA (Prop.) [Tw] -+ 356.1 AA (USA) [Ac] -+
DIN Wk. 3.7165, 320 AA 356.1, 239
226A DIN (D) [Ac] -+
DIN GB-AISi9Cu3, 283 319 Old AA (USA) [Ac]-+ 356.2 AA (USA) [Ac] -+
AA 319.0,237 AA 356.2, 239
226D DIN (D) [Ac] -+
NF A-S9U3, 258
AA 319.1,237 356.2 A AA (USA) [Ac] -+
AA 319.2, 237 AA A356.2, 262
230 DIN (D) [Ac]-+
DIN GBD-AISi12, 284
319.0 AA (USA) [Ac]-+ 357 Old AA (USA) [Ac) -+
AA 319.0,237 AA 3570,239
230A DIN (D) [Ac] -+
319.0 BAA (USA) [Ac]-+ AA 357.1 , 239
DIN GB-AISi12, 283
AA B3190, 276 357.0 AA (USA) [Ac)-+
231 DIN (D) [Ac] -+
319.1 AA (USA) [Ac]-+ AA 3570,239
DIN GBD-AISi12(Cu), 284
AA319.1,237 357.0 A AA (USA) [Ac) -+
231A DIN (D) [Ac] -+
319.1 A AA (USA) [Ac] -+ AA A357.0, 262
DIN GB-AISi12(Cu), 283
AA A319.1, 262 357.0 D AA (USA) [Ac]-+
233 DIN (D) [Ac]-+
319.2 AA (USA) [Ac)-+ AA 0357.0, 281
DIN GB-AISi10Mg(Cu), 283
AA 319.2, 237 357.1 AA (USA) [Ac)-+
235 DIN (D) [Ac]-+
332.0 AA (USA) [Ac) -+ AA 357.1 , 239
DIN GB-AISi5Mg, 283
AA 3320,237 357.2 A AA (USA) [Ac) -+
239 DIN (D) [Ac]-+
332.1 AA (USA) [Ac] -+ AA A357.2, 262
DIN GBD-AISi1 OMg, 284
AA 332.1, 237 35B.0 AA (USA) [Ac) -+
239A DIN (D) [Ac] -+
332.2 AA (USA) [Ac) -+ AA 358.0, 239
DIN GB-AISi10Mg, 283
AA 332.2, 237 35B.2 AA (USA) [Ac] -+
240.0 AA (USA) [Ac] -+
333 Old AA (USA) [Ac] -+ AA 358.2, 239
AA 240.0, 235
AA 333.0, 237 359 Old AA (USA) [Ac) -+
240.1 AA (USA) [Ac]-+ AA 333.1, 238 AA 359.0, 239
AA 240.1, 235 333.0 AA (USA) [Ac] -+ AA 359.2, 239
242 DIN (D) [Ac] -+ AA 333.0, 237 359.0 AA (USA) [Ac) -+
DIN GB-AIMg3, 282
333.1 AA (USA) [Ac) -+ AA 359.0, 239
242.0 AA (USA) [Ac] -+ AA 333.1, 238 359.2 AA (USA) [Ac] -+
AA 242.0,235 VAW Vera1226A, 290 AA 359.2, 239
242.0 A AA (USA) [Ac] -+ 336.0 AA (USA) [Ac) -+ VAW Silumin-Beta, 288
AA A242.0, 261 AA 336.0, 238 360 Old AA (USA) [Ac] -+
242.1 AA (USA) [Ac] -+ 336.1 AA (USA) [Ac) -+ AA 360.0,239
AA 242.1, 235 AA 336.1, 238 AA 360.2, 239
242.1 A AA (USA) [Ac]-+ 336.2 AA (USA) [Ac) -+ 360.0 AA (USA) [Ac) -+
AA A242.1, 261 AA 336.2, 238 AA 360.0, 239
242.2 AA (USA) [Ac] -+ VAW Veral Si12CuNiMg(H), 294 360.0 A AA (USA) [Ac) -+
AA 242.2, 235 339.0 AA (USA) [Ac] -+ AA A360.0, 262
242.2 A AA (USA) [Ac] -+ AA 339.0, 238 360.1 A AA (USA) [Ac] -+
AA A242.2, 261 339.1 AA (USA) [Ac) -+ AAA360.1,263
243 DIN (D) [Ac] -+ AA 339.1, 238 360.2 AA (USA) [Ac) -+
DIN GB-AIMg3Si, 282 349 DIN (D) [Ac) -+ AA 360.2, 239
244 DIN (D) [Ac] -+ DIN GBD-AIMg9, 284 VAW Veral Si10Mg(D), 293
DIN GB-AIMg5, 283
Alloy Cross-Reference Listing 435
360.2 A AA (USA) [Ac] -+ 390.2 AA (USA) [Ac] -+ 509 SAE (USA) [Mc] -+
AA A360.2, 263 AA 390.2,241 ASTM ZK51A, 314
361.1 AA (USA) [Ac] -+ 392 Old AA (USA) [Ac] -+ BS MAG4. 310
AA 361.1,239 AA 392.0,241 510 SAE (USA) [Mw] -+
VAW Veral 233, 290 AA 392.2,241 ASTM AZ31B, 301
363 Old AA (USA) [Ac] -+ 392.0 AA (USA) [Ac] -+ Comeca Al31B, 301
AA 363.0, 239 AA 392.0, 241 Magnesium Elektron Al31, 300
AA 363.1, 240 392.2 AA (USA) [Ac]-+ 511.0 AA (USA) [Ac] -+
363.0 AA (USA) [Ac] -+ AA 392.2,241 AA 511.0, 242
AA 363.0, 239 393.0 AA (USA) [Ac] -+ 511.1 AA (USA) [Ac] -+
363.1 AA (USA) [Ac] -+ AA 393.0, 241 AA 511.1, 242
AA 363.1,240 393.1 AA (USA) [Ac]-+ 511.2 AA (USA) [Ac] -+
364 Old AA (USA) [Ac] -+ AA 393.1, 241 AA 5112,242
AA 364.0, 240 393.2 AA (USA) [Ac] -+ 512.0 AA (USA) [Ac]-+
AA 364.2, 240 AA 393.2, 241 AA 512.0.242
364.0 AA (USA) [Ac] -+ 409.2 AA (USA) [Ac] -+ 512.2 AA (USA) [Ac]-+
AA 364.0, 240 AA 409.2, 241 AA 512.2,242
364.2 AA (USA) [Ac] -+ VAW Silumin-Delta, 288 VAW Veral Mg3Si(H), 292
AA 364.2, 240 413.0 A AA (USA) [Ac]-+ 513.0 AA (USA) [Ac]-+
369.0 AA (USA) [Ac] -+ AAA413.0,263 AA 513.0,242
AA 3690,240 413.0 AA (USA) [Ac]-+ 513.2 AA (USA) [Ac]-+
369.1 AA (USA) [Ac] -+ AA4130,241 AA 513.2, 242
AA 3691,240 413.1 A AA (USA) [Ac]-+ 514.0 AA (USA) [Ac]-+
VAW Silumin-Kappa, 289 AAA413.1,263 AA 5140,243
380 Old AA (USA) [Ac] -+ 413.1 AA (USA) [Ac]-+ 514.1 AA (USA) [Ac]-+
AA 380.0, 240 AA413.1,241 AA514.1,243
AA 380.2,240
413.2 A AA (USA) [Ac]-+ 514.2 AA (USA) [Ac] -+
380.0 AA (USA) [Ac] -+ AA A413.2. 263 AA 514.2, 243
AA 380.0, 240
443.0 AA (USA) [Ac] -+ VAW Veral Mg3, 291
380.0 A AA (USA) [Ac] -+ AA 443.0,242 VAW Veral Mg3(H), 291
AA A380.0, 263 AA B443.0, 277 515.0 AA (USA) [Ac] -+
380.0 B AA (USA) [Ac] -+ AA C443.0, 278 AA 515.0, 243
AA B3800, 276 443.0 A AA (USA) [Ac] -+ 515.2 AA (USA) [Ac]-+
380.1 A AA (USA) [Ac]-+ AA A443.0, 264 AA 515.2. 243
AA A380.1, 263 443.1 AA (USA) [Ac] -+ 516.0 AA (USA) [Ac] -+
380.1 BAA (USA) [Ac]-+ AA 443.1, 242 AA 5160,243
AA B380.1, 276 443.1 A AA (USA) [Ac] -+ 518.0 AA (USA) [Ac]-+
380.2 AA (USA) [Ac] -+ AA A443.1, 264 AA 518.0, 243
AA 380.2, 240 443.1 BAA (USA) [Ac] -+ 518.1 AA (USA) [Ac]-+
380.2 A AA (USA) [Ac] -+ AA B443.1, 277 AA518.1,243
AA A380.2, 263 443.1 C AA (USA) [Ac] -+ VAW Veral Mg9, 292
384 Old AA (USA) [Ac] -+ AA C443.1, 278 518.2 AA (USA) [Ac]-+
AA 518.2,243
AA 384.0, 240 443.2 AA (USA) [Ac] -+
AA 384.1, 240 VAW Veral Mg9(H), 292
AA4432.242
AA 384.2, 240
443.2 C AA (USA) [Ac] -+ 520 SAE (USA) [Mw] -+
AA 385.0, 240 ASTM AZ61A, 301
AA C443.2, 278
AA 385.1, 241 520.0 AA (USA) [Ac] -+
AA A384.0, 263 444.0 A AA (USA) [Ac] -+
AA 520.0, 243
AA A384.1, 263 AA A444.0, 264
-+ 520.2 AA (USA) [Ac] -+
384.0 AA (USA) [Ac] -+ 444.2 AA (USA) [Ac]
AA 444.2, 242
AA 520.2, 243
AA 384.0, 240 VAW Veral Mg1 O(H), 292
384.0 A AA (USA) [Ac] -+ 444.2 A AA (USA) [Ac] -+
522 SAE (USA) [Mw] -+
AA A384.0, 263 AA A444.2, 264
ASTM MIA, 312
445.2 AA (USA) [Ac] -+
384.1 AA (USA) [Ac]-+ 523 SAE (USA) [Mw] -+
AA 384.1, 240 AA 445.2, 242
ASTM Al80A, 302
384.1 A AA (USA) [Ac] -+ 500 SAE (USA) [Mc] -+
ASTM AZ92A, 304
524 SAE (USA) [Mw] -+
AA A3841. 263 ASTM ZK60A. 315
384.2 AA (USA) [Ac] -+ 501 SAE (USA) [Mc] -+
ASTM AZ91A, 303
531 SAE (USA) [Mw] -+
AA 384.2, 240 ASTM Al61A, 301
385.0 AA (USA) [Ac] -+ 501 A SAE (USA) [Mc] -+
532 SAE (USA) [Mw] -+
AA 385.0, 240 ASTM AZ91 B, 303
ASTM Al80A, 302
385.1 AA (USA) [Ac]-+ 502 SAE (USA) [Mc] -+ BS 2L 121,297
AA 385.1, 241 ASTM AM100A, 298 CEN MG-P-61, 311
390 Old AA (USA) [Ac] -+ 505 SAE (USA) [Mc] -+ DIN 3.5812, 297
AA 390.0, 241 ASTM AZ81 A, 302 Magnesium Elektron Al80, 302
AA 390.2, 241 ASTM AZ91C, 303 NF G-A7Z1, 306
RIMA Al91 C, 303 NF G-A8Z, 306
390.0 AA (USA) [Ac] -+
AA 390.0,241 506 SAE (USA) [Mc] -+ 533 SAE (USA) [Mw] -+
ASTM EZ33A, 306
390.0 A AA (USA) [Ac] -+ 507 SAE (USA) [Mcw] -+
ASTM MIA, 312
AA A390.0, 263 535.0 A AA (USA) [Ac] -+
ASTM HK31A. 307
390.1 A AA (USA) [Ac] -+ AA A535.0, 264
AA A390.1, 263
436 Alloy Cross-Reference Listing
3579 (I) [Aw] -+ 4015E AMS (USA) [Aw] -+ 4043 AMS (USA) [Aw] -+
AA 2017, 160 AA 5052, 177 AA 6061, 191
AA 2017A, 161 Alusuisse Peraluman 253, 224 Alusuisse Anticorodal OBO, 216
AlusuisseAvional100,218 CEN 5052, 177 Alusuisse Anticorodal-OB2, 216
Alusuisse Avional-102, 218 DIN Wk. 3.3523 (AIMg2.5), 146 CEN 6061, 192
CEN 2017A, 161 Hoogovens 5520, 185 DIN Wk. 3.3211 (AIMg1 SiCu) 145
DIN Wk. 3.1325 (AICuMg1), 144 VAW 63/52, 148 Hoogovens 6560, 198
Hoogovens 2170, 164 4016E AMS (USA) [Aw] -+ Reynolds R-2000, 227
NF A-U4G, 218 AA 5052, 177 4043 (UK) [Aw] -+
3581 (I) [Aw] -+ Alusuisse Peraluman 253, 224 AA 4043, 172
AA 2014, 159 CEN 5052, 177 4043A AA (USA) [Aw] -+
AA 2014A, 160 DIN Wk. 3.3523 (AIMg2.5), 146 AA 4043A, 172
Alusuisse Avional-660/662, 219 Hoogovens 5520, 185 CEN 4043A, 172
CEN 2014, 160 VAW 63/52, 148 4045 AA (USA) [Aw] -+
DIN Wk. 3.1255 (AICuSiMn), 144 4017E AMS (USA) [Aw] -+ AA 4045, 172
Hoogovens 2140, 164 AA 5052.177 CEN 4045, 172
3583 (I) [Aw] -+ Alusuisse Peraluman 253, 224 4045 AMS (USA) [Aw] -+
AA 2024, 161 CEN 5052, 177 AA 7075,203
Alusuisse Avional 150, 219 DIN Wk. 3.3523 (AIMg2.5), 146 Alusuisse Perunal215, 226
Alusuisse Avional 152, 219 Hoogovens 5520, 185 CEN 7075, 204
CEN 2024, 162 VAW 63/52, 148 DIN Wk. 3.4365 (AIZnMgCu1.5), 147
DIN Wk. 3.1355 (AICuMg2), 144 40250 AMS (USA) [Aw] -+ Hoogovens 7750, 207
Hoogovens 2240, 165 AA 6061, 191 4047 AA (USA) [Aw] -+
NF A-U4G1, 218 Alusuisse Antieorodal OBO, 216 AA 4047, 173
3600 (I) [Ae] -+ Alusuisse Antieorodal-OB2, 216
CEN 6061, 192 4047 (UK) [Aw] -+
BS LM16, 285
DIN Wk. 3.3211 (AIMg1 SiCu), 145 AA 4047, 173
CEN 45300, 252
UNI 3600, 247 Hoogovens 6560, 198 4047A AA (USA) [Aw] -+
AA 4047A, 173
3620-TA7 (China) [Tew] -+ Reynolds R-2000, 227
3620-TA7, 326 40260 AMS (USA) [Aw] -+ CEN 4047A, 173
4049 AMS (USA) [Aw] -+
3620-TA7 (China) [Tw] -+ AA 6061, 191
Alusuisse Anticorodal OBO, 216 AA 7075 Alclad, 204
AMS 4910, 327
AMS 4926, 328 Alusuisse Anticorodal-OB2, 216 4050 AMS (USA) [Aw] -+
ASTM Grade 6, 333 CEN 6061, 192 AA 7050,202
DINWk. 3.7115, 318 DIN Wk. 3.3211 (AIMg1SiCu), 145 CEN 7050, 202
3735 (I) [Aw] -+
Hoogovens 6560, 198 4053 AMS (USA) [Aw] -+
Reynolds R-2000, 227 AA 6061, 191
AA 7075,203
Alusuisse Perunal215, 226 4027E AMS (USA) [Aw] -+ Alusuisse Anticorodal OBO, 216
CEN 7075, 204 AA 6061,191 Alusuisse Anticorodal-OB2, 216
DIN Wk. 3.4365 (AIZnMgCu1.5), 147 Alusuisse Anticorodal OBO, 216 CEN 6061, 192
Hoogovens 7750, 207 Alusuisse Anticorodal-OB2, 216 DIN Wk. 3.3211 (AIMg1 SiCu), 145
CEN 6061, 192 Hoogovens 6560, 198
3736 (I) [Aw] -+
DIN Wk. 3.3211 (AIMg1SiCu), 145 Reynolds R-2000, 227
AA 7075,203
Alusuisse Perunal 215, 226
Hoogovens 6560, 198 4054 (S) [Aw] -+
Reynolds R-2000, 227 AA 3103, 169
CEN 7075, 204
DIN Wk. 3.4365 (AIZnMgCu15), 147 4028 AMS (USA) [Aw] -+ CEN 3103,169
Hoogovens 7750, 207 AA 2014, 159 DIN AI Mn1, 213
Alusuisse Avional-660/662, 219 DIN Wk, 30315 (AIMn1), 143
4004 (S) [Aw] -+
CEN 2014, 160 Hoogovens 3000, 166
AA 1OBOA, 153
Alusingen 111, 149
DIN Wk. 3.1255 (AICuSiMn), 144 4069 AMS (USA) [Aw] -+
Hoogovens 2140, 164 AA 5052, 177
Alusuisse Pure Aluminium 99.B, 227
CEN 10BOA, 153 4029 AMS (USA) [Aw] -+ Alusuisse Peraluman 253, 224
DIN AI 99.B, 210 AA 2014, 159 CEN 5052, 177
DIN Wk. 302B5 (AI99.B), 143 Alusuisse Avional-660/662, 219 DIN Wk, 3.3523 (AIMg2.5), 146
CEN 2014, 160 Hoogovens 5520, 185
4004 AA (USA) [Aw] -+
DIN Wk. 3.1255 (AICuSiMn), 144 VAW 63/52, 148
AA 4004, 171
CEN 4004, 171
Hoogovens 2140, 164 4070F AMS (USA) [Aw] -+
4032 AA (USA) [Aw] -+ AA 5052, 177
4005 (S) [Aw] -+
AA 4032,172 Alusuisse Peraluman 253, 224
AA 1070, 152
Hoogovens 1070, 153 4032 NF (F) [Aw] -+ CEN 5052, 177
AA 4032, 172 DIN Wk. 3.3523 (AIMg2.5), 146
4006 AA (USA) [Aw] -+
AA 4006, 171 4032 (UK) [Aw] -+ Hoogovens 5520, 185
AA 4032. 172 VAW 63/52, 148
CEN 4006, 171
4071 F AMS (USA) [Aw] -+
4007 (S) [Aw] -+ 4037 AMS (USA) [Aw] -+
AA 2024, 161 AA 5052, 177
AA 1050A, 152 AlusUisse Peraluman 253, 224
Alusingen 134, 149 Alusuisse Avional 150, 219
Alusuisse Avional 152, 219 CEN 5052, 177
Alusuisse Pure Aluminium 99.5, 227 DIN Wk. 3.3523 (AIMg2.5), 146
CEN 1050A, 152 CEN 2024, 162
DIN Wk. 3.1355 (AICuMg2), 144 Hoogovens 5520, 185
DIN AI 99.5, 210 VAW 63/52, 148
DIN Wk. 3.0255 (AI99.5), 143 Hoogovens 2240, 165
NF A-U4G1, 218 4078 AMS (USA) [Aw] -+
NF A-5, 210
NF A-5L, 210 4043 AA (USA) [Aw] -+ AA 7075,203
Alusuisse Perunal 215, 226
4007 AA (USA) [Aw] -+ AA 4043,172
CEN 7075, 204
AA 4007, 171 DIN Wk, 3.4365 (AIZnMgCu1.5), 147
CEN 4007, 171 Hoogovens 7750, 207
440 Alloy Cross-Reference Listing
4079 AMS (USA) [Aw] ~ 4106 (S) [Aw] ~ 4150C AMS (USA) [Aw] ~
AA 6061, 191 AA 5005, 174 AA 6061, 191
Alusuisse Anlicorodal OBO, 216 Alusuisse Peraluman-l 00 (101), 223 Alusuisse Anlicorodal OBO, 216
Alusuisse Anlicorodal-OB2, 216 CEN 5005, 174 Alusuisse Anlicorodal-OB2, 216
CEN 6061, 192 DIN Wk. 3.3315 (AIMgl), 146 CEN 6061, 192
DIN Wk. 3.3211 (AIMglSiCu), 145 Hoogovens 5010, 174 DIN Wk. 3.3211 (AIMgl SiCu), 145
Hoogovens 6560, 198 4107 AMS (USA) [Aw] ~ Hoogovens 6560, 198
Reynolds R-2000, 227 AA 7050,202 Reynolds R-2000, 227
4080E AMS (USA) [Aw] ~ CEN 7050, 202 4157 AMS (USA) [Aw] ~
AA 6061, 191 4108 AMS (USA) [Aw] ~ AA 7049,202
Alusuisse Anlicorodal OBO, 216 AA 7050,202 4160 AMS (USA) [Aw] ~
Alusuisse Anlicorodal-OB2, 216 CEN 7050, 202 AA 6061, 191
CEN 6061, 192 Alusuisse Anlicorodal OBO, 216
4111 AMS (USA) [Aw] ~
DIN Wk. 3.3211 (AIMg1 SiCu), 145 Alusuisse Anlicorodal-OB2, 216
AA 7049,202
Hoogovens 6560, 198 CEN 6061, 192
Reynolds R-2000, 227 41148 AMS (USA) [Aw] ~
AA 5052, 177 DIN Wk. 3.3211 (AIMgl SiCu), 145
4081A AMS (USA) [Aw] ~ Hoogovens 6560, 198
Alusuisse Peraluman 253, 224
AA 6061, 191 Reynolds R-2000, 227
CEN 5052, 177
Alusuisse Anlicorodal OBO, 216 4161 AMS (USA) [Aw] ~
DIN Wk. 3.3523 (AIMg2.5), 146
Alusuisse Anlicorodal-OB2, 216 AA 6061, 191
Hoogovens 5520, 185
CEN 6061, 192 Alusuisse Anlicorodal OBO, 216
VAW 63/52. 148
DIN Wk. 3.3211 (AIMglSiCu), 145 Alusuisse Anlicorodal-OB2, 216
Hoogovens 6560, 198 4115 AMS (USA) [Aw] ~
AA 6061, 191 CEN 6061, 192
Reynolds R-2000, 227 DIN Wk. 3.3211 (AIMgl SiCu), 145
Alusuisse Anlicorodal OBO, 216
4082E AMS (USA) [Aw] ~ Hoogovens 6560. 198
Alusuisse Anlicorodal-OB2, 216
AA 6061, 191 Reynolds R-2000, 227
CEN 6061, 192
Alusuisse Anlicorodal OBO, 216 4162 AMS (USA) [Aw] ~
DIN Wk. 3.3211 (AIMglSiCu), 145
Alusuisse Anlicorodal-OB2, 216 AA 2219, 165
Hoogovens 6560, 198
CEN 6061, 192 CEN 2219, 165
Reynolds R-2000, 227
DIN Wk. 3.3211 (AIMgl SiCu), 145
4116A AMS (USA) [Aw] ~ 4179 AMS (USA) [Aw] ~
Hoogovens 6560, 198
AA 6061. 191 AA 7175,205
Reynolds R-2000, 227
Alusuisse Anlicorodal OBO, 216 CEN 7175, 206
40830 AMS (USA) [Aw] ~
Alusuisse Anlicorodal-OB2, 216 4200 AMS (USA) [Aw] ~
AA 6061, 191
CEN 6061, 192 AA 7049,202
Alusuisse Anlicorodal OBO, 216
DIN Wk. 3.3211 (AIMgl SiCu), 145 4201 AMS (USA) [Aw] ~
Alusuisse Anlicorodal-OB2, 216
Hoogovens 6560, 198 AA 7050,202
CEN 6061, 192
Reynolds R-2000, 227 CEN 7050, 202
DIN Wk. 3.3211 (AIMglSiCu), 145
Hoogovens 6560, 198 4117A AMS (USA) [Aw] ~ 4202 AMS (USA) [Aw] ~
Reynolds R-2000, 227 AA 6061, 191 AA 7475,206
Alusuisse Anlicorodal OBO, 216 CEN 7475, 207
4084 AMS (USA) [Aw] ~
Alusuisse Anlicorodal-OB2, 216
AA 7475,206 4204 AMS (USA) [Aw] ~
CEN 6061, 192
CEN 7475, 207 AA 7010, 199
DIN Wk. 3.3211 (AIMglSiCu), 145 Alusuisse Conlal, 220
4085 AMS (USA) [Aw] ~ Hoogovens 6560, 198
AA 7475,206 CEN 7010, 199
Reynolds R-2000, 227
CEN 7475, 207 4205 AMS (USA) [Aw] ~
41278 AMS (USA) [Aw] ~ AA 7010, 199
4089 AMS (USA) [Aw] ~ AA 6061, 191
AA 7475,206 Alusuisse Conlal, 220
Alusuisse Anlicorodal OBO, 216
CEN 7475, 207 CEN 7010, 199
Alusuisse Anlicorodal-OB2, 216
4090 AMS (USA) [Aw] ~ CEN 6061, 192 4216 AMS (USA) [Aw] ~
AA 7475,206 DIN Wk. 3.3211 (AIMglSiCu), 145 AA6013,189
CEN 7475, 207 Hoogovens 6560, 198 4217 AMS (USA) [Ac] ~
4101 AMS (USA) [Aw] ~ Reynolds R-2000, 227 AA 356.0, 239
AA 2124, 164 4130 AMS (USA) [Aw] ~ 4240 AMS (USA) [Ac] ~
CEN 2124, 164 AA 2025, 162 AA 520.0,243
4103 (S) [Aw] ~ 4144 AMS (USA) [Aw] ~ 4241 AMS (USA) [Ac] ~
AA 6060,190 AA 2219, 165 AA D357.0, 281
Alunord 6060.4B, 191 CEN 2219,165 4251 AMS (USA) [Aw] ~
Alunord 6060.79, 191 4146 AMS (USA) [Aw] ~ AA 2090,163
Alusuisse Anlicorodal 045/0501053, 216 AA 6061, 191 4252 AMS (USA) [Aw] ~
Alusuisse Extrudal-043, 221 Alusuisse Anlicorodal OBO, 216 AA 7150,205
Alusuisse Extrudal-050, 221 Alusuisse Anlicorodal-OB2, 216 4260 AMS (USA) [Ac] ~
BOAl UK AM62, 214 CEN 6061, 192 AA 356.0, 239
CEN 6060, 190 DIN Wk. 3.3211 (AIMg1SiCu), 145
DIN AI Mg SiO.3, 212 4281 AMS (USA) [Ac] ~
Hoogovens 6560, 198
DIN AI Mg SiO.5, 212 AA 355.0, 238
Reynolds R-2000, 227
DIN Wk. 3.3206 (AIMgSiO.5), 145 4284 AMS (USA) [Ac] ~
4148 AMS (USA) [Aw] ~
NF AGS, 210 AA 356.0, 239
AA 7175,205
4104 AA (USA) [Aw] ~ CEN 7175, 206 4306 AMS (USA) [Aw] ~
AA4104,173 AA 7150.205
4149 AMS (USA) [Aw] ~
CEN4104,173 4307 AMS (USA) [Aw] ~
AA 7175,205
CEN 7175, 206 AA 7150,205
4320 AMS (USA) [Aw] ~
AA 7149,205
CEN 7149,205
Alloy Cross-Reference Listing 441
4340 AMS (USA) [Aw] -+ 4383 AMS (USA) [Mw] -+ 4455 AMS (USA) [Me] -+
AA 7050,202 ASTM HM21A, 307 ASTM AM1 OOA, 298
CEN 7050, 202 4384E AMS (USA) [Mew] -+ 4483 AMS (USA) [Me] -+
4341 AMS (USA) [Aw] -+ ASTM HK31A, 307 ASTM AM 1OOA, 298
AA 7050,202 4387 AMS (USA) [Mw] -+ 4484 AMS (USA) [Me] -+
CEN 7050, 202 ASTM ZK21A, 314 ASTM AZ92A, 304
4342 AMS (USA) [Aw] -+ 4388 AMS (USA) [Mw] -+ 4490 AMS (USA) [Me] -+
AA 7050,202 ASTM HM31A, 307 ASTM AZ91A, 303
CEN 7050, 202 -+
4389 AMS (USA) [Mw] -+ 4490E AMS (USA) [Me]
4343 AA (USA) [Aw] -+ ASTM HM31A, 307 ASTM AZ91 B, 303
AA4343,173 4390 AMS (USA) [Mw] -+ -+
4507 (I) [Aw]
CEN 4343, 173 ASTM HM21A, 307 AA 1050, 151
4343 AMS (USA) [Aw] -+ 4417 AMS (USA) [Mc] -+ AA 1050A, 152
AA 7149,205 ASTM EQ21A, 305 Alusingen 134, 149
CEN 7149, 205 Magnesium Elektron EQ21, 304 Alusuisse Pure Aluminium 99.5, 227
4344 AMS (USA) [Aw] -+ 4418C AMS (USA) [Me]-+
CEN 1050A, 152
AA 7175,205 DIN AI 99.5, 210
ASTM QE22A, 312
CEN 7175, 206 DIN Wk. 3.0255 (AI99.5), 143
BS MAG13, 310
4345 AMS (USA) [Aw] -+ 4418E AMS (USA) [Me]-+
Hoogovens1000.151
AA 7150,205 NF A-5, 210
Magnesium Elektron QE22, 304 NF A-5L, 210
4347 AMS (USA) [Aw] -+ 4420 AMS (USA) [Me]-+ VAW 99/52, 149
AA6013,189
4350K AMS (USA) [Mw] -+
ASTM AZ63A, 302 -+
4508 (I) [Aw]
AECMA MG-P-63, 311
4422 AMS (USA) [Me] -+ AA 1070, 152
ASTM AZ63A, 302 AA 1070A, 153
ASTM AZ61A, 301
BS MAG-E-121M, 308 4424 AMS (USA) [Me] -+ Alunord 1370-70, 158
ASTM AZ63A, 302 CEN 1070A, 153
DIN 3.5612, 297
Magnesium Elecktron AZ61, 301 4425 AMS (USA) [Me] -+ Hoogovens 1070, 153
NF G-A6Z1, 306 ASTM ZE63A, 314 4509 (I) [Aw]-+
4352 AMS (USA) [Mw] -+ 4426 AMS (USA) [Mew] -+ AA 1060, 152
ASTM WE54A, 313 AA 1080A, 153
ASTM ZK60A, 315
Magnesium Elektron WE54, 305 Alusingen 111, 149
BS MAG-x-161 , 309
Alusuisse Pure Aluminium 99.S, 227
DIN Wk. 3.5161,297 4427 AMS (USA) [Mew] -+ CEN 10S0A, 153
NF G-Z5Zr, 306 ASTM WE43A, 313
DIN AI 99.S, 210
4355 (S) [Aw]-+ Magnesium Elektron WE43, 305
DIN Wk. 302S5 (AI99.S), 143
AA2011,159 4434 AMS (USA) [Me] -+ Lawson Mardon (LM) Star 1602, 158
Alusuisse Decoltal 500, 220 ASTM AZ92A, 304
4510 (I) [Aw]-+
CEN 2011, 159 4437A AMS (USA) [Me] -+ AA 5005, 174
DIN Wk. 3.1S55 (AICuBiPb), 145 ASTM AZ91 C, 303 Alusuisse Peraluman-100 (101), 223
4357 AMS (USA) [Mw] -+ ASTM AZ91 D, 303 CEN 5005, 174
ASTM AZ31 B, 301 BS MAG3, 309 DIN Wk. 3.3315 (AIMg1), 146
4358A AMS (USA) [Mw] -+ DIN Wk. 3.5912, 297 Hoogovens 5010, 174
AECMA MG-P-63, 311 NF G-A9Z1, 306
4511 (I) [Aw]-+
ASTM Al61A, 301 RIMA Al91 C, 303
AA 5251, 182
BS MAG-E-121M, 308 44388 AMS (USA) [Me] -+ Alusuisse Peraluman-226, 223
DIN 3.5612, 297 ASTM ZH62A, 314 CEN 5251, 183
Magnesium Elecktron AZ61, 301 BS MAG9, 310 DIN Wk. 3.3526 (AIMg2MnO.3), 146
NF G-A6Z1 , 306 4439A AMS (USA) [Me] -+ -+
4514 (I) [Ae]
43600 AMS (USA) [Mw] -+ AECMA MG-C-43, 311 AAA413.2,263
ASTM AlSOA, 302 ASTM ZE41A, 314 BS LM6, 285
BS2L121,297 BS MAG5, 310 VAW Silumin, 288
CEN MG-P-61, 311 DIN Wk. 3.5101, 297
DIN 3.5812, 297 NF G-Z4TR, 306
4543 AA (USA) [Aw] -+
AA 4543, 173
Magnesium Elektron AlSO, 302 4439C AMS (USA) [Me] -+ 4900 AMS (USA) [Tw] -+
NF G-A7Z1, 306 Magnesium Elektron ZE41, 305
NF G-ASZ, 306 ASTM Grade 3, 332
44428 AMS (USA) [Me] -+ Deutsche Titan Tikrutan RT 1S, 343
4362 AMS (USA) [Mw] -+ AECMA MG-C-91, 311 DIN Wk. 3.7055, 318
ASTM ZK60A, 315 ASTM EZ33A, 306 Timetal 65A, 323
BS MAG-x-161, 309 BS MAG6, 310 Titanium Industries GR-3, 331
DIN Wk. 3.5161, 297
NF G-Z5Zr, 306
DIN Wk. 3.5103, 297
4901 AMS (USA) [Tw] -+
44420 AMS (USA) [Me] -+ ASTM Grade 4, 332
4363 AMS (USA) [Mw] -+ Magnesium Elektron EZ33, 304 CEN Ti P99003, 341
ASTM HM21A, 307
4443 AMS (USA) [Me] -+ Deutsche Titan Tikrutan RT 20, 343
4375H AMS (USA) [Mw] -+ ASTM ZK51A, 314 DIN Wk. 3.7065, 318
ASTM AZ31 B, 301 BS MAG4, 310 Timetal 75A, 323
Comeca AZ31 B, 301
Magnesium Elektron Al31, 300
4445 AMS (USA) [Mew] -+ Titanium Industries GR-4, 331
ASTM HK31A, 307 4902 AMS (USA) [Tw] -+
4376 AMS (USA) [Mw] -+ 4446 AMS (USA) [Me] -+ ASTM Grade 2, 332
ASTMAZ31B,301 CEN Ti P99002, 341
ASTM AZ91 E, 303
4382 AMS (USA) [Mw] -+ 44478 AMS (USA) [Me] -+ Deutsche Titan Tikrutan RT 15, 343
ASTM AZ31 B, 301 DIN Wk. 3.7035, 318
ASTM HZ32A, 307
Comeca AZ31 B, 301 NF T 40,336
BS MAGS, 310
Magnesium Elektron Al31, 300 Timetal 50A, 323
4453 AMS (USA) [Me] -+ Titanium Industries GR-2, 331
ASTM AZ92A, 304
442 Alloy Cross-Reference Listing
4905 AMS (USA) [Tw] -+ 4921 AMS (USA) [Tw] -+ 4932 AMS (USA) [Tw]-+
ASTM Grade 5, 333 ASTM Grade 4,333 ASTM Grade 5, 333
Timetal 6-4, 321 CEN Ti P99003, 341 BS 2TA10, 317
4906 AMS (USA) [Tw] -+ Deutsche Titan Tikrutan RT 20, 343 CEN Ti P63, 340
ASTM Grade 5, 333 DIN Wk. 3.7065, 318 Deutsche Titan Tikrutan LT 31, 342
BS 2TA10, 317 Teledyne Allvac 70, 329 DIN LW 3.7164, 319
CEN Ti P63, 340 Timetal 100A, 323 DIN Ti AI6 V4, 339
Deutsche Titan Tikrutan LT 31, 342 4924 AMS (USA) [Tw] -+ DIN Wk. 3.7165, 320
DIN LW 3.7164, 319 3620-TA7, 326 DTD 5163, 328
DIN Ti AI6 V4, 339 ASTM Grade 6, 333 NF TA6V, 336
DIN Wk. 3.7165, 320 DIN Wk. 3.7115, 318 NF Ti P64001, 340
DTD 5163,328 DTD 5083, 328 Timetal 6-4, 321
NF TA6V, 336 NF TA 5E, 336 4933 AMS (USA) [Tw] -+
NF Ti P64001 , 340 VT51,344 MIL R-81588, 334
TimetaI6-4, 321 AMS 4909,327 TimetaI8-1-1,322
4907 AMS (USA) [Tw] -+ AMS 4924,327 4934 AMS (USA) [Tw] -+
ASTM Grade 5, 333 4925A AMS (USA) [Tw] -+ ASTM Grade 5, 333
ASTM Grade 23, 334 AECMA Ti P62, 340 BS 2TA10, 317
BS 2TA10, 317 ASTM 17,321 CEN Ti P63, 340
CEN Ti P63, 340 ASTM F7, 331 Deutsche Titan Tikrutan LT 31, 342
Deutsche Titan Tikrutan LT 31, 342 Crucible Steel Co. C130AM, 330 DIN LW 3.7164, 319
DIN LW 3.7164, 319 DTD 5053, 328 DIN Ti AI6 V4, 339
DIN Ti AI6 V4, 339 IMI 314A, 324 DIN Wk. 37165, 320
DIN Wk. 3.7165, 320 NF TA 5M, 336 DTD 5163, 328
DTD 5163,328 4926 AMS (USA) [Tw] -+ NF TA6V, 336
NF TA6V, 336 3620-TA7, 326 NF Ti P64001, 340
NF Ti P64001, 340 AMS 4910. 327 Timetal 6-4, 321
Timetal 6-4, 321 AMS 4926. 328 4935 AMS (USA) [Tw] -+
4908 AMS (USA) [Tw]-+ ASTM Grade 6, 333 ASTM Grade 5,333
UNS R56080, 334 DIN Wk. 3.7115, 318 BS 2TA10, 317
4909 AMS (USA) [Tw] -+ 3620-TA7, 326 DTD 5083, 328 CEN Ti P63, 340
ASTM Grade 6, 333 NF TA 5E, 336 Deutsche Titan Tikrutan LT 31. 342
DIN Wk. 3.7115, 318 4928 AMS (USA) [Tw] -+ DIN LW 3.7164, 319
DTD 5083, 328 Deutsche Titan Tikrutan LT 31, 342 DIN Ti AI6 V4, 339
NF TA 5E, 336 DIN Wk. 3.7165, 320 DIN Wk. 37165, 320
VT51,344 Titanium Industries GR-5, 331 DTD 5163, 328
4910 AMS (USA) [Tw]-+ Teledyne Allvac 6-4, 329 NF TA6V, 336
3620-TA7,326 4928L AMS (USA) [Tw] -+ NF Ti P64001, 340
AMS 4910, 327 AMS 4905, 326 Timetal 6-4, 321
AMS 4926, 328 ASTM Grade 5, 333 4936 AMS (USA) [Tw]-+
ASTM Grade 6, 333 BS 2TA10, 317 AMS 4918,327
DIN Wk. 3.7115, 318 CEN Ti P63, 340 4941 AMS (USA) [Tw] -+
DTD 5083, 328 DIN LW 3.7164, 319 NF T 40,336
NF TA 5E, 336 DIN Ti AI6 V4, 339 ASTM Grade 2,332
4911 AMS (USA) [Tw] -+ DTD 5163,328 CEN Ti P99002, 341
AMS 4905, 326 NFTA6V, 336 Deutsche Titan Tikrutan RT 15, 343
ASTM Grade 5, 333 NF Ti P64001, 340 DIN Wk. 3.7035, 318
BS 2TA10, 317 Timetal 6-4, 321 Timetal 50A, 323
CEN Ti P63, 340 4930 AMS (USA) [Tw]-+ Titanium Industries GR-2, 331
Deutsche Titan Tikrutan LT 31, 342 ASTM Grade 5, 333 4942 AMS (USA) [Tw] -+
DIN LW. 3.7164, 319 ASTM Grade 23, 334 ASTM Grade 2, 332
DIN Ti AI6 V4, 339 BS 2TA10, 317 CEN Ti P99002, 341
DIN Wk. 3.7165, 320 CEN Ti P63, 340 Deutsche Titan Tikrutan RT 15, 343
DTD 5163,328 Deutsche Titan Tikrutan LT 31, 342 DIN Wk. 3.7035, 318
NF TA6V, 336 DIN LW 3.7164, 319 Titanium Industries GR-2, 331
NF Ti P64001, 340 DIN Ti AI6 V4, 339 4943 AMS (USA) [Tw] -+
TimetaI6-4, 321 DIN Wk. 3.7165, 320 Ti-3AI-2.5V, 337
Titanium Industries GR-5, 331 DTD 5163, 328 ASTM 3AI-2.5V, 321
4915 AMS (USA) [Tw]-+ NF TA6V, 336 ASTM Grade 9, 333
MIL R-81588, 334 NF Ti P64001, 340 TimetaI3-2.5,318
Timetal 8-1-1, 322 Teledyne Allvac 6-4 ELI, 329 4944 AMS (USA) [Tw] -+
Timetal 6-4, 321
4916 AMS (USA) [Tw] -+ ASTM 3AI-2.5V, 321
MIL R-81588, 334 4931 AMS (USA) [Tw] -+ ASTM Grade 9, 333
Timetal 8-1-1, 322 ASTM Grade 23, 334 TimetaI3-2.5,318
Titanium Industries Ti-15-3, 339 Teledyne Allvac 6-4 ELI, 329 4951 AMS (USA) [Tw] -+
4917 AMS (USA) [Tw]-+ ASTM Grade 2, 332
Ti-13V-11Cr-3AI,339 CEN Ti P99002, 341
AMS 4917, 327 Deutsche Titan Tikrutan RT 15, 343
Crucible Steel Co. B 120 VCA, 330 DIN Wk. 3.7035, 318
4919 AMS (USA) [Tw] -+ Titanium Industries GR-2, 331
DIN LW 3.7144,319
4920 AMS (USA) [Tew] -+
ASTM Grade 5, 333
Timetal 6-4, 321
Alloy Cross-Reference Listing 443
4954 AMS (USA) [Tew] -+ 4974 AMS (USA) [Tw]-+ 5042 AA (USA) [Aw] -+
ASTM Grade 5, 333 IMI 551,324 AA 5042, 176
BS 2TA10, 317 IMI 679, 325 VAW 63/37, 148
CEN Ti P63, 340 Timetal 551, 325 5049 AA (USA) [Aw] -+
Deutsche Titan Tikrutan LT 31, 342 Timetal 679, 325 AA 5049, 176
DIN LW 3.7164, 319 4975 AMS (USA) [Tw] -+ CEN5049, 176
DIN Ti AI6 V4, 339 AMS 4919,327 5049 NF (F) [Aw] -+
DIN Wk. 3.7165, 320 Deutsche Titan Tikrutan LT 24, 341 AA 5049, 176
DTD 5163, 328 DIN LW 3.7144,319 CEN5049, 176
NF TA6V, 336 DIN Wk. 3.7145, 319
NF Ti P64001, 340 5050 AA (USA) [Aw] -+
Teledyne Allvac 6-2-4-2, 328
Timetal 6-4, 321 AA 5050, 176
Titanium Industries Ti-6-2-4-2, 338
Alusuisse Peraluman 150/151, 223
4959 AMS (USA) [Tw] -+ 4976 AMS (USA) [Tw] -+ CEN 5050, 176
Crucible Steel Co. B 120 VCA, 330 AMS 4919, 327
Ti-13V-11 Cr-3AI, 339 5050 (UK) [Aw] -+
Deutsche Titan Tikrutan LT 24, 341
AA 5050, 176
4965 AMS (USA) [Tw] -+ DIN LW 3.7144,319
Alusuisse Peraluman 150/151. 223
ASTM Grade 5, 333 DIN Wk. 3.7145, 319 CEN 5050, 176
BS 2TA10, 317 Titanium Industries Ti-6-2-4-2, 338
5050B AA (USA) [Aw] -+
CEN Ti P63, 340 4977 AMS (USA) [Tw] -+
Deutsche Titan Tikrutan LT 31, 342 AA 5050B, 176
Beta III, 330
DIN LW 3.7164, 319 5051A AA (USA) [Aw]-+
4978 AMS (USA) [Tw] -+ AA 5051A, 176
DIN Ti AI6 V4, 339 AMS 4918, 327
DIN Wk. 3.7165, 320 CEN 5051A, 176
Teledyne Allvac 6-6-2, 329 DIN AI Mg18, 212
DTD 5163,328
NF TA6V, 336 4979 AMS (USA) [Tw]-+ DIN Wk. 3.3326 (AIMg18), 146
AMS 4918, 327
NF Ti P64001, 340 5052 AA (USA) [Aw] -+
Teledyne Allvac 6-4, 329 DIN LW 3.7174, 320
AA 5052, 177
Timetal 6-4, 321 Teledyne Allvac 6-6-2, 329
Alusuisse Peraluman 253, 224
Timetal 6-6-2, 321
4966 AMS (USA) [Tew]-+ CEN 5052, 177
3620-TA7, 326 4980 AMS (USA) [Tw]-+ DIN Wk. 3.3523 (AIMg2.5), 146
ASTM Grade 6, 333 Beta III, 330 Hoogovens 5520, 185
DIN Wk. 3.7115, 318 4981 AMS (USA) [Tw] -+ VAW 63/52, 148
DTD 5083, 328 IM1646,325 5052 NF (F) [Aw] -+
NF TA 5E, 336 Teledyne Allvac 6-2-4-6, 329 AA 5052, 177
4967 AMS (USA) [Tew] -+ Timetal 6-2-4-6, 321 CEN 5052, 177
AMS 4905, 326 Titanium Industries Ti-6-2-4-6, 338 DIN Wk. 3.3523 (AIMg2.5), 146
Deutsche Titan Tikrutan LT 31, 342 4983 AMS (USA) [Tw] -+ VAW 63/52, 148
DIN Wk. 3.7165, 320 Timetal 10-2-3, 322 5052 (UK) [Aw] -+
4967 AMS (USA) [Tw] -+ Titanium Industries Ti-1 0-2-3, 338 AA 5052, 177
Teledyne Allvac 6-4, 329 4984 AMS (USA) [Tw] -+ Alusuisse Peraluman 253, 224
4967E AMS (USA) [Tew] -+ TimetaI10-2-3,322 CEN 5052, 177
ASTM Grade 5, 333 4986 AMS (USA) [Tw] -+ DIN Wk. 3.3523 (AIMg2.5), 146
BS 2TA10, 317 Timetal 10-2-3, 322 Hoogovens 5520, 185
CEN Ti P63, 340 VAW 63/52, 148
4987 AMS (USA) [Tw]-+
DIN LW 3.7164, 319 Timetal 10-2-3, 322 5056 AA (USA) [Aw] -+
DIN Ti AI6 V4, 339 AA 5056, 177
4996 AMS (USA) [Tw]-+
DTD 5163, 328 AMS 4907,327 5056A AA (USA) [Aw] -+
NF TA6V, 336 AA 5056A, 178
5005 AA (USA) [Aw] -+
NF Ti P64001, 340 DIN Wk. 3.3555 (AIMg5), 147
AA 5005, 174
Timetal 6-4, 321
Alusuisse Peraluman-1 00 (101), 223 5056A (UK) [Aw] -+
4970 AMS (USA) [Tw] -+ CEN 5005, 174 AA5019,175
UNS R56740, 334 DIN Wk. 3.3315 (AIMg1), 146 AA 5056A, 178
4971 AMS (USA) [Tw] -+ Hoogovens 5010,174 AA 5356, 184
CEN 5019, 175
AMS 4918,327 5005 NF (F) [Aw] -+
Teledyne Allvae 6-6-2, 329 CEN 5356, 184
AA 5005, 174
4971A AMS (USA) [Tw]-+ DIN Wk. 3.3555 (AIMg5), 147
Alusuisse Peraluman-100 (101),223
DIN LW 3.7174,320 CEN 5005, 174 5074-74 (I) [Ae] -+
Timetal 6-6-2, 321 DIN Wk. 3.3315 (AIMg1), 146 AA361.1,239
4972 AMS (USA) [Tw] -+ Hoogovens 5010, 174 VAW Veral 233, 290
Teledyne Allvac 8-1-1,329 5005 (UK) [Aw] -+ 5075-79 (I) [Ae] -+
4972A AMS (USA) [Tw] -+ AA 5005, 174 AA 333.1, 238
AMS 4915, 327 Alusuisse Peraluman-1 00 (101), 223 AA B380.1, 276
MIL R-81588, 334 CEN 5005, 174 VAW Veral 226(D), 290
Timetal 8-1-1 , 322 DIN Wk. 3.3315 (AIMg1), 146 VAW Vera1226A, 290
4973A AMS (USA) [Tw] -+ Hoogovens 5010, 174 5077-74 (I) [Ae] -+
AMS 4915, 327 5005A AA (USA) [Aw] -+ VAW Veral Si5MgA, 293
MIL R-81588, 334 AA 5005A, 174 5079-74 (I) [Ae]-+
Timetal 8-1-1, 322 Alusingen 214, 150 AAA413.1,263
4974 AMS (USA) [Tw]-+ DIN AI Mg1, 212 VAW Veral 231 (D), 290
AMS 4974,328 5010 AA (USA) [Aw] -+ VAW Veral 231A, 290
BS TA18, 337 AA5010,174 5080-74 (I) [Ae] -+
BS TA20, 337 5019 AA (USA) [Aw]-+ AA 518.1,243
UNS R54790, 334 AA5019,175 VAW Veral Mg9, 292
CEN 5019, 175
444 Alloy Cross-Reference Listing
5083 AA (USA) [Aw] -+ 5205 AA (USA) [Aw] -+ 5552 AA (USA) [Aw] -+
AA 5083, 178 AA 5205, 182 AA 5552,185
Alusuisse Alplan, 213 Alusingen 294, 151 5554 AA (USA) [Aw] -+
Alusuisse Peraluman-460/462, 225 AlusUisse Peraluman-708, 225 AA 5554,186
Alusuisse Peraluman-462, 225 5251 AA (USA) [Aw] -+ 5554 (UK) [Aw] -+
Alusuisse Peraluman-470, 225 AA 5251 182
CEN 5083, 179 AA 5554,186
Alusuisse Peraluman-226, 223
Hoogovens 5510, 185 5556A AA (USA) [Aw]-+
CEN 5251, 183
Superform Metals 5083 SPF, 179 AA 5556A, 186
DIN Wk, 3,3526 (AIMg2MnO,3), 146
5083 NF (F) [Aw] -+ 5556A (UK) [Aw] -+
5251 NF (F) [Aw] -+
AA 5083,178 AA 5556A, 186
AA 5251, 182
Alusuisse Peraluman-460/462, 225 Alusuisse Peraluman-226, 223 5652 AA (USA) [Aw] -+
Alusuisse Peraluman-462, 225 CEN 5251,183 AA 5652, 186
CEN 5083, 179 DIN Wk, 3,3526 (AIMg2MnO,3), 146 5652 (UK) [Aw] -+
Hoogovens5510,185
5251 (UK) [Aw] -+ AA 5652, 186
Superform Metals 5083 SPF, 179
AA 5251, 182 5657 AA (USA) [Aw] -+
5083 (UK) [Aw] -+ Alusuisse Peraluman-226, 223 AA 5657, 186
AA 5083, 178 CEN 5251, 183 Alusingen 278, 150
Alusuisse Peraluman-460/462, 225 DIN Wk, 3,3526 (AIMg2MnO,3), 146 Alusingen 289, 150
Alusuisse Peraluman-462, 225
5252 AA (USA) [Aw] -+ Alusuisse Peraluman-860, 225
CEN 5083, 179 Alusuisse Peraluman-863, 225
AA 5252, 183
Hoogovens 5510, 185 CEN 5657, 186
Alusingen 297, 151
Superform Metals 5083 SPF, 179 DIN AI 99,85 Mg1, 211
Alusuisse Peraluman-875, 226
5086 AA (USA) [Aw] -+ 5657 (UK) [Aw] -+
5252 (UK) [Aw] -+
AA 5086,179 AA 5657, 186
AA 5252, 183
Alusuisse Peraluman-41 0/412, 224 Alusingen 278, 150
Alusuisse Peraluman-875, 226
CEN 5086, 180 Alusingen 289, 150
Hoogovens 5503, 185 5254 AA (USA) [Aw] -+
Alusuisse Peraluman-860, 225
NF A-G4MC, 210 AA 5254, 183
Alusuisse Peraluman-863, 225
5086 NF (F) [Aw] -+ 5356 AA (USA) [Aw] -+ CEN 5657, 186
AA 5086, 179 AA 5356, 184 DIN AI 99,85 Mg1 211
CEN 5356, 184
Alusuisse Peraluman-41 0/412, 224 5754 AA (USA) [Aw] -+
CEN 5086, 180 5356 NF (F) [Aw] -+ AA 5754, 187
Hoogovens 5503, 185 AA 5356, 184 Alusingen 234, 150
NF A-G4MC, 210 CEN 5356, 184 Alusuisse Peraluman-300 (301), 224
5086 (UK) [Aw] -+ 5452-64 (I) [Aw] -+ Alusuisse Peraluman-302, 224
AA 5086, 179 AA 5083,178 CEN 5754, 187
Alusuisse Peraluman-41 0/412, 224 AA 5086,179 DIN AI Mg3 EO, 212
CEN 5086, 180 Alusuisse Peraluman-41 0/412, 224 DIN Wk, 3,3535 (AIMg3), 147
Hoogovens 5503, 185 Alusuisse Peraluman-460/462, 225 Hoogovens 5030, 175
NF A-G4MC, 210 Alusuisse Peraluman-462, 225 NF A-G3, 210
5087 AA (USA) [Aw] -+ CEN 5083, 179 5754 NF (F) [Aw] -+
AA 5087, 180 CEN 5086, 180 AA 5754, 187
CEN 5087, 180 Hoogovens 5503, 185 Alusingen 234, 150
Hoogovens 5510, 185
51 SAE (USA) [Mw] -+ Alusuisse Peraluman-300 (301), 224
NF A-G4MC, 210 Alusuisse Peraluman-302, 224
ASTM MIA, 312 Superform Metals 5083 SPF, 179 CEN 5754, 187
5150 AA (USA) [Aw]-+ 5454 AA (USA) [Aw] -+ DIN AI Mg3 EO, 212
AA 5150, 180 DIN Wk, 3,3535 (AIMg3), 147
AA 5454, 184
5154 AA (USA) [Aw]-+ Alusuisse Peraluman-260, 224 Hoogovens 5030, 175
AA 5154, 181 CEN 5454, 185 NF A-G3, 210
DIN AIMg3,5, 212 Hoogovens 5400, 184 5764 (I) [Aw] -+
5154A (UK) [Aw] -+ 5454 NF (F) [Aw] -+ AA 5005A, 174
AA 5154, 181 AA 5454, 184 Alusingen 214, 150
AA5154A,181 Alusuisse Peraluman-260, 224 DIN AI Mg1, 212
AA 5254,183 CEN 5454, 185 5764-66 (I) [Aw] -+
CEN 5154A, 181 Hoogovens 5400, 184 AA 5005, 174
DIN AIMg3,5, 212
5454 (UK) [Aw] -+ Alusuisse Peraluman-1 00 (101), 223
5154A AA (USA) [Aw]-+ AA 5454, 184 CEN 5005, 174
AA5154A,181 Alusuisse Peraluman-260, 224 DIN Wk, 3,3315 (AIMg1), 146
CEN 5154A, 181 CEN 5454, 185 Hoogovens 5010, 174
5154B AA (USA) [Aw] -+ Hoogovens 5400, 184 5832-2 ISO (EUR) [Tw] -+
AA 51548, 181 5456 AA (USA) [Aw] -+ Teledyne Allvac 30, 329
5182 AA (USA) [Aw] -+ AA 5456, 185 Teledyne Allvac 40, 329
AA5182,181 5456A AA (USA) [Aw] -+ Teledyne Allvac 55, 329
CEN 5182, 182 AA 5456A, 185 Teledyne Allvac 70, 329
VAW 63/45, 148 Alusuisse Peraluman-502, 225 5832-3 ISO (EUR) [Tw] -+
5182 NF (F) [Aw]-+ CEN 5456A, 185 Teledyne Allvac 6-4 ELI, 329
AA 5182, 181 5457 AA (USA) [Aw] -+ Teledyne Allvac 6-4, 329
CEN 5182, 182 AA 5457, 185 5832-11 ISO (EUR) [Tw] -+
VAW 63/45, 148
5457 (UK) [Aw] -+ Teledyne Allvac 6-7, 329
5183 AA (USA) [Aw] -+ AA 5457, 185 6003 AA (USA) [Aw] -+
AA5183,182 5505 AA (USA) [Aw] -+ AA 6003, 188
CEN 5183, 182
AA 5505, 185
Alloy Cross-Reference Listing 445
6005 AA (USA) [Aw] ~ 6061 (UK) [Aw] ~ 6101B AA (USA) [Aw] ~
AA 6005, 188 AA 6061,191 AA 6101 B, 196
Alunord 6081-11, 194 Alusuisse Anticorodal 080, 216 Alusuisse Anticorodal-041, 215
6005A AA (USA) [Aw] ~ Alusuisse Anticorodal-082, 216 6101C AA (USA) [Aw] ~
AA 6005A, 188 CEN 6061, 192 DIN E-AI Mg SiO.5, 220
Alunord 6005A, 188 DIN Wk. 3.3211 (AIMg1 SiCu), 145
6106 AA (USA) [Aw] ~
Alusuisse Anticorodal 062, 216 Hoogovens 6560, 198
AA 6106,196
CEN 6005A, 189 Reynolds R-2000, 227
Alunord 6106, 196
DIN AI Mg SiO.7, 213 6063 (UK) [Aw] ~ CEN 6106, 196
NF A-SGO.5, 218 AA 6060,190
6111 AA (USA) [Aw] ~
6005A NF (F) [Aw] ~ AA 6063,193
AA6111,196
AA 6005, 188 Alunord 6060.48, 191
Alunord 6060.79, 191 6151 AA (USA) [Aw] ~
Alunord 6081-11, 194 AA6151,197
CEN 6005A, 189 BOAl UKAM62, 214
CEN 6060, 190 6162 AA (USA) [Aw] ~
6012 AA (USA) [Aw] ~ AA6162,197
CEN 6063, 193
AA 6012, 189
Alusuisse Anticorodal Pb-107, 217 DIN AI Mg SiO.5, 212 6170-68 (I) [Aw] ~
CEN 6012, 189 NFAGS, 210 AA6061,191
6013 AA (USA) [Aw] ~ 6063 AA (USA) [Aw] + Alusuisse Anticorodal 080, 216
AA 6063,193 Alusuisse Anticorodal-082, 216
AA6013,189
CEN 6063, 193 CEN 6061, 192
6016 AA (USA) [Aw] ~ DIN AI Mg SiO.5, 212 DIN Wk. 3.3211 (AIMg1 SiCu), 145
Alusuisse Anticorodal120, 217 Hoogovens 6560, 198
6063A AA (USA) [Aw] ~
6018 AA (USA) [Aw] ~ AA 6063A, 193 Reynolds R-2000, 227
AA6018,190 BOAl UK AM65, 214 6181 AA (USA) [Aw] ~
Alusuisse Anticorodal Pb-109, 217 AA6181,197
6066 AA (USA) [Aw] ~
6053 (UK) [Aw] ~ AA 6066,193 DIN AI Mg SiO.8, 213
AA6053,190 6181 NF (F) [Aw] ~
6081 AA (USA) [Aw] ~
6053 AA (USA) [Aw] ~ AA 6081,194 AA6005,188
AA 6053,190 Alunord 6081-11,194
6081 NF (F) [Aw] ~
6056 AA (USA) [Aw] ~ CEN 6005A, 189
AA6081,194
AA 6056,190 6201 AA (USA) [Aw] ~
CEN 6056, 190 6082 AA (USA) [Aw] ~
AA 6201,197
AA 6082,194
6060 AA (USA) [Aw] ~ Alusuisse Anticorodal110/112, 217 6250-68 (I) [Ae] ~
AA 6060, 190 Alusuisse Anticorodal1121114, 217 AA 336.1 , 238
Alusuisse Anticorodal 045/0501053, 216 Alusuisse Anticorodal-1 00/1 05, 216 AA 336.2, 238
Alusuisse Extrudal-043, 221 BOAl UK AM68, 215 VAW Veral Si12CuNiMg(H), 294
Alusuisse Extrudal-050, 221 CEN 6082, 195 VAW Veral Si12CuNiMg, 294
DIN AI Mg SiO.3, 212 DIN AI Mg Si1, 213 6251-68 (I) [Ae] ~
DIN Wk. 3.3206 (AIMgSiO.5), 145 DIN Wk. 3.2315 (AIMgSi1), 145 AA 393.2, 241
6060 NF (F) [Aw] ~ Hoogovens 6010, 189 VAW Veral Si18CuNiMg(H), 294
AA 6060,190 NF A-SGMO.7, 218 6253 AA (USA) [Aw] ~
Alunord 6060.48, 191
Alunord 6060.79, 191
6082 NF (F) [Aw] + AA 6253, 197
AA 6082,194 6262 AA (USA) [Aw] ~
CEN 6060, 190 Alusuisse Anticorodal110/112, 217 AA 6262,197
6060 (UK) [Aw] ~ Alusuisse Anticorodal112/114, 217 CEN 6262, 197
AA 6060, 190 Alusuisse Anticorodal-1 00/1 05, 216 6351 AA (USA) [Aw] ~
Alunord 6060.48, 191 BOAl UK AM68, 215 AA 6351,198
Alunord 6060.79, 191 CEN 6082, 195 Alunord 6082-50, 195
BOAl UK AM62, 214 DIN AI Mg Si1, 213
CEN 6060, 190 6361 (I) [Aw] ~
DIN Wk. 3.2315 (AIMgSi1), 145
DIN AI Mg SiO.5, 212 AA 3004, 167
Hoogovens 6010, 189
NF AGS, 210 CEN 3004, 167
NF A-SGMO.7, 218
Hoogovens 3540, 171
6061 AA (USA) [Aw] ~ 6082 (UK) [Aw] ~ Hoogovens3541,171
AA 6061,191 AA6082,194 VAW 61103, 148
Alusuisse Anticorodal 080, 216 Alusuisse Anticorodal 110/112, 217
Alusuisse Anticorodal-082, 216 6362 (I) [Aw] ~
Alusuisse Anticorodal112/114, 217
CEN 6061, 192 AA2011,159
Alusuisse Anticorodal-100/105, 216
DIN Wk. 3.3211 (AIMg1SiCu), 145 Alusuisse Decoltal 500, 220
BOAl UK AM68, 215
Hoogovens 6560, 198 CEN 2011, 159
CEN 6082, 195
Reynolds R-2000, 227 DIN Wk. 3.1855 (AICuBiPb), 145
DIN AI Mg Si1, 213
6061 NF (F) [Aw] ~ DIN Wk. 3.2315 (AIMgSi1), 145 6443 AA (USA) [Aw] ~
AA 6061,191 Hoogovens 6010, 189 DIN Wk. 3.3208 (AI99.9MgSi), 145
Alusuisse Anticorodal 080, 216 NF A-SGMO.7, 218 6463 (UK) [Aw] ~
Alusuisse Anticorodal-082, 216 6101 AA (USA) [Aw] ~ AA 6463,198
CEN 6061, 192 AA6101,196 6463 AA (USA) [Aw] ~
DIN Wk. 3.3211 (AIMg1 SiCu), 145 CEN6101,196 AA 6463,198
Hoogovens 6560, 198 6101A AA (USA) [Aw] ~ DIN AI 99.85 Mg Si, 211
Reynolds R-2000, 227 AA 6101A, 196 DIN AI 99.85 Mg SiO.4, 211
DIN Wk. 3.2305 (AIMgSi), 145 6951 AA (USA) [Aw] ~
6101A (UK) [Aw] ~ AA6951,198
AA6101A,196 7001 AA (USA) [Aw] ~
DIN Wk. 3.2305 (AIMgSi), 145 AA 7001,199
7005 AA (USA) [Aw] ~
AA 7005,199
446 Alloy Cross-Reference Listing
10849 VSM (CH) [Aw]-+ A2X1 (J) [Aw]-+ AS (ex USSR) [Aw] -+
AA 5005, 174 AA 5052, 177 AA 1060, 152
AA 5052, 177 Alusuisse Peraluman 253, 224 Lawson Mardon (LM) Star 1602, 158
AA 5056, 177 CEN 5052, 177 A7 NF (F) [Ac]-+
Alusuisse Peraluman 253, 224 DIN Wk. 3.3523 (AIMg2.5), 146 AA 170.1,233
Alusuisse Peraluman-1 00 (101), 223 Hoogovens 5520, 185 VAW Veral 99.7, 289
CEN 5005, 174 VAW 63/52, 148
A7 NF (F) [Aw]-+
CEN 5052, 177 A2X2 (J) [Aw]-+ AA 1070,152
DIN Wk. 3.3315 (AIMg1), 146 AA 5056, 177 AA 1070A, 153
DIN Wk. 3.3523 (AIMg2.5), 146
Hoogovens 5010, 174
A2X8 (J) [Aw]-+ Alunord 1370-70, 158
AA 5005, 174 CEN 1070A, 153
Hoogovens 5520, 185
Alusuisse Peraluman-100 (101), 223 Hoogovens 1070, 153
VAW 63/52, 148
10850 VSM (CH) [Aw]-+
CEN 5005, 174 A8 NF (F) [Aw]-+
DIN Wk. 3.3315 (AIMg1), 146 AA 1060, 152
AA 6082, 194 Hoogovens 5010,174 AA 1080, 153
Alusuisse Anticorodal 110/112, 217
Alusuisse AnticorodaI112/114, 217
A3X1 (J) [Aw]-+ AA 1080A, 153
AA 2014, 159 AA 1175, 155
Alusuisse Anticorodal-1 00/1 05, 216
Alusuisse Avional-660/662, 219 Alusingen 111, 149
BOAL UKAM68, 215
CEN 2014, 160 Alusuisse Pure Aluminium 99.8, 227
CEN 6082, 195
DIN Wk. 3.1255 (AICuSiMn), 144 CEN 1080A, 153
DIN AI Mg Si1, 213
Hoogovens 2140, 164 DIN AI 99.8, 210
DIN Wk. 3.2315 (AIMgSI1), 145
Hoogovens 6010, 189 A4 NF (F) [Aw]-+ DIN Wk. 30285 (AI998), 143
AA 1200, 156 Lawson Mardon (LM) Star 1602, 158
NF A-SGMO.7, 218
10851 VSM (CH) [Aw] -+ Alusuisse Pure Aluminium 99.0, 226 A8 (welding rod) (UK) [Mc] -+
CEN 1200, 156 ASTM AZ81, 302
AA 6463, 198
DIN AI 9985 Mg Si, 211
DIN AI 99, 210 A 8-GO.5 NF (F) [Aw] -+
Hoogovens 1010, 151 DIN AI 99.95 MgO.5, 211
DIN AI 99.85 Mg SiOA, 211
Lawson Mardon (LM) Star 1201, 156
10853 VSM (CH) [Aw]-+ VAW 99/00, 149
A9 NF (F) [Aw]-+
AA 2218, 164 AA 1090, 154
VAW 99/01, 149
AA 1199, 155
10858 VSM (CH) [Aw] -+ A4-G/L NF (F) [Aw] -+ Alusingen 119, 149
AA 7075,203 DIN AIFeMg, 212 Alusuisse Pure Aluminium 99.9,227
Alusuisse Perunal 215, 226
CEN 7075, 204
A4/L NF (F) [Aw] -+ CEN 1090, 154
AA 8011A, 207 CEN 1199,155
DIN Wk. 3A365 (AIZnMgCu1.5), 147
CEN 8011A, 208 DIN AI 999, 211
Hoogovens 7750, 207
10859 VSM (CH) [Aw] -+
DIN Wk. 3.0915 (AIFeSi), 144 A 9-GO.5 NF (F) [Aw] -+
AA 7005, 199
A4X1 (J) [Aw]-+ DIN AI 99.9 MgO.5, 211
AA 2618, 165 A 9-G1 NF (F) [Aw] -+
A5 NF (F) [Ac]-+ AA 5457, 185
A AA150.1,233 DIN AI 99.9 Mg1, 211
VAW Veral 99.5, 289 A13 Old AA (USA) [Ac]-+
AlAO (ex USSR) [Aw] -+ A5 NF (F) [Aw]-+ AAA413.0,263
VAW 99/01, 149 AA 1050, 151 AAA413.1,263
AO (ex USSR) [Aw] -+ AA 1050A, 152 AA A413.2, 263
AA 1200, 156 Alusingen 134, 149 A43 Old AA (USA) [Ac] -+
Alusuisse Pure Aluminium 99.0, 226 Alusuisse Pure Aluminium 99.5, 227 AA C443 0, 278
CEN 1200, 156 CEN 1050A, 152 AA C443.1, 278
DIN A199, 210 DIN AI 99.5, 210 AA C443.2, 278
Hoogovens 1010, 151 DIN Wk. 3.0255 (AI99.5), 143
Hoogovens 1000, 151
A45 NF (F) [Aw] -+
Lawson Mardon (LM) Star 1201, 156 AA 1100, 154
VAW 99/00, 149 NF A-5, 210
CEN 1100,154
VAW 99/52, 149
VAW 99/01, 149
-+ A85 NF (F) [Aw] -+
A1X1 (J) [Aw] -+ A5 (ex USSR) [Aw]
AA 1050,151
AA 1085,153
AA 1050, 151 Alusingen 184, 150
Hoogovens 1000, 151 Hoogovens 1000, 151 Alusuisse Pure Aluminium 99.85, 227
VAW 99/52, 149 VAW 99/52, 149 CEN 1085, 153
A1X3 (J) [Aw] -+ A5/ADO (ex USSR) [Aw] -+ DIN AI 99.85, 211
AA 1200, 156 AA 1050, 151
Hoogovens 1000, 151
A 85-G1 NF (F) [Aw] -+
Alusuisse Pure Aluminium 99.0, 226 AA 5657, 186
CEN 1200, 156 VAW 99/52, 149 Alusingen 278, 150
DIN AI 99, 210 A 58 NF (F) [Aw] -+ Alusingen 289, 150
Hoogovens 1010, 151 AA 1350, 157 Alusuisse Peraluman-860, 225
Lawson Mardon (LM) Star 1201, 156 Alusuisse Pure Aluminium 99.5 E, 227 Alusuisse Peraluman-863, 225
VAW 99/00, 149 CEN 1350, 157 CEN 5657, 186
VAW 99/01, 149 Hoogovens 1001, 151 DIN AI 99.85 Mg1, 211
A1X18 (J) [Aw] -+ A 5/L NF (F) [Aw] -+ A 85-GS NF (F) [Aw] -+
AA 1050,151 AA 1350A, 157 AA 6463,198
Hoogovens 1000, 151 DIN E-AI, 220 DIN AI 99.85 Mg Si, 211
VAW 99/52, 149 DIN Wk. 30257 (E-AI), 143 DIN AI 99.85 Mg SiOA, 211
A2 (Prop.) [Aw] -+ A 5L NF (F) [Aw] -+ A85-GT NF (F) [Aw] -+
AA 1070A, 153 AA 1350, 157 AA 5150,180
Alunord 1370-70, 158 Alusuisse Pure Aluminium 99.5 E, 227
CEN 1350, 157
A99 NF (F) [Aw] -+
CEN 1070A, 153 DIN Wk. 30305 (AI99.9), 143
Hoogovens 1001,151
NF A-5L, 210
Alloy Cross-Reference Listing 449
A108 Old AA (USA) [Ac]-+ A380 Old AA (USA) [Ac] -+ A1100 (J) [Aw] -+
AA 308.0, 236 AA A380.0, 263 AA 1100, 154
A132 Old AA (USA) [Ac]-+ AA A380.1, 263 CEN 1100, 154
AA 3360,238 AA A380.2, 263 A1200 (J) [Aw]-+
AA 336.1, 238 AA B380.0, 276 AA 1200, 156
AA 336.2, 238 AA B380.1, 276 Alusuisse Pure Aluminium 99.0, 226
A140 Old AA (USA) [Ac]-+ A380.0 Old AA (USA) [Ac] -+ CEN 1200, 156
AA 240.0, 235 AA 3800.240 DIN AI 99, 210
AA 240.1, 235 A390 AA (USA) [Ac] -+ Hoogovens 1010, 151
A142 Old AA (USA) [Ac]-+ Affimet Calypso 87P, 281 Lawson Mardon (LM) Star 1201, 156
AA A242 0, 261 A390 Old AA (USA) [Ac] -+ VAW 99/00, 149
AA A390.0, 263 VAW 99/01, 149
AAA242.1,261
AA A242.2, 261 AA A390.1, 263 A1200P (J) [Aw]-+
A180 Old AA (USA) [Ac]-+ A390.1 AA (USA) [Ac]-+ AA 1200, 156
AA 308.1, 236 VAW Veral Si17Cu4Mg(H), 294 Alusuisse Pure Aluminium 99.0, 226
CEN 1200, 156
AA 308.2, 236 A393.2 AA (USA) [Ac] -+ DIN AI 99, 210
A201.2 Old AA (USA) [Ac] -+ VAW Veral Si18CuNiMg(H), '294 Hoogovens 1010, 151
AAA201.1,261 A413.0 AA (USA) [Ac]-+ Lawson Mardon (LM) Star 1201, 156
A20S.2 AA (USA) [Ac] -+ NF A-S12, 258 VAW 99/00, 149
Affimet Calypso 25M. 278 A413.1 AA (USA) [Ac]-+ A2011 (Aus) [Aw] -+
A214 Old AA (USA) [Ac]-+ VAW VeraI231(D), 290 AA 2011, 159
AA 513.0,242 VAW Veral Si12A(D), 293 CEN 2011, 159
AA 513.2, 242 A413.2 AA (USA) [Ac]-+ A2011 (J) [Aw] -+
A218 Old AA (USA) [Ac]-+ BS LM6, 285 AA 2011, 159
AA A535.0, 264 VAW Silumin, 288 Alusuisse Decoltal 500, 220
AA A535.1, 264 VAW Veral Si12A, 293 CEN 2011, 159
A240.0 Old AA (USA) [Ac] -+ A514.0 Old AA (USA) [Ac] -+ DIN Wk. 3.1855 (AICuBiPb), 145
AA 240.0, 235 AA 513.0,242 A2014 (J) [Aw] -+
A240.1 Old AA (USA) [Ac] -+ A514.2 Old AA (USA) [Ac] -+ AA 2014, 159
AA 240.1, 235 AA 513.2, 242 AA 2014A, 160
A319.0 Old AA (USA) [Ac]-+ A612 Old AA (USA) [Ac]-+ Alusuisse Avional-660/662, 219
AA 319.0, 237 AA 710.0, 244 CEN 2014, 160
AA 710.1,244 DIN Wk. 3.1255 (AICuSiMn), 144
A319.1 AA (USA) [Ac]-+
AA 711.0, 244 Hoogovens 2140, 164
VAW Veral 225, 290
A2014P (J) [Aw] -+
A332.0 Old AA (USA) [Ac] -+ A712.0 Old AA (USA) [Ac]-+
AA 710.0,244 AA 2014, 159
AA 336.0, 238
Alusuisse Avional-660/662, 219
A332.1 Old AA (USA) [Ac] -+ A712.1 Old AA (USA) [Ac]-+
CEN 2014, 160
AA 336.1 , 238 AA 710.1,244
DIN Wk. 3.1255 (AICuSiMn), 144
VAW Veral Si12CuNiMg, 294 A750 Old AA (USA) [Ac] -+ Hoogovens 2140, 164
A332.2 Old AA (USA) [Ac] -+ AA 8510,245
A2017P (J) [Aw]-+
AA 336.2. 238 AA851.1,245
AA2017A,161
VAW Veral Si12CuNiMg(H), 294 A850.0 Old AA (USA) [Ac] -+ Alusuisse Avional 100, 218
A333.0 Old AA (USA) [Ac] -+ AA 851.0,245 Alusuisse Avional-l02, 218
AA 333.0, 237 A850.1 Old AA (USA) [Ac] -+ CEN 2017A, 161
A344 Old AA (USA) [Ac] -+ AA 851.1,245 DIN Wk. 3.1325 (AICuMgl), 144
AA A444.0, 264 A1050 (Aus) [Aw] -+ NF A-U4G, 218
AA A444.2, 264 AA 1050A, 152 A2024 (Aus) [Aw] -+
A356 Old AA (USA) [Ac] -+ CEN 1050A, 152 AA 2024. 161
AA A356.0. 262 A1050 (J) [Aw]-+ CEN 2024, 162
AA A3562, 262 AA 1050A, 152 A2024P (J) [Aw] -+
A356.0 AA (USA) [Ac] -+ Alusingen 134, 149 AA 2024, 161
NF A-S7G03, 257 Alusuisse Pure Aluminium 99.5, 227 Alusuisse Avional 150, 219
A356.0 Old AA (USA) [Ac] -+ CEN 1050A, 152 Alusuisse Avional 152,219
AA 356.0, 239 DIN AI 99.5, 210 CEN 2024, 162
DIN Wk. 3.0255 (AI99.5), 143 DIN Wk. 3.1355 (AICuMg2), 144
A356.2 AA (USA) [Ac] -+ NF A-5, 210 Hoogovens 2240, 165
VAW Pantal 7, 287 NF A-5L, 210 NF A-U4Gl, 218
A357 Old AA (USA) [Ac] -+ A1050P (J) [Aw]-+ A2117 (J) [Aw] -+
AA A357.0, 262 AA 1050, 151 AA2117,164
AA A357.2, 262 Hoogovens 1000. 151 DIN Wk. 3.1305 (AICu2.5MgO.5), 144
A357.0 AA (USA) [Ac] -+ VAW 99/52, 149 A02950 UNS (USA) [Ac] -+
NF A-S7G06, 257 A1 070 (J) [Aw] -+ AA 295.0, 235
A360 Old AA (USA) [Ac] -+ AA 1070A, 153 A3003 (J) [Aw] -+
AA A3600, 262 Alunord 1370-70, 158 AA 3003,166
AA A360.1, 263 CEN 1070A, 153 Alusuisse Aluman 100, 213
AA A360.2, 263 A1080 (J) [Aw]-+ CEN 3003, 167
A360.0 AA (USA) [Ac] -+ AA 1080A, 153 Hoogovens 3530, 170
NF A-S10G, 258 Alusingen 111, 149 Lawson Mardon (LM) Star 3103, 169
Valfond Silafont 36, 288 Alusuisse Pure Aluminium 99.8, 227 NF 3003, 167
A380 AA (USA) lAc] -+ CEN 1080A, 153 Reynolds Tread-Brite, 228
NF A-S9U3, 258 DIN AI 99.8, 210 VAW 41/20, 148
DIN Wk. 30285 (AI99.8), 143
450 Alloy Cross-Reference Listing
A3004 (J) [Aw) ~ A5454P (J) [Aw) ~ A91230 UNS (USA) [Aw) ~
AA 3004,167 AA 5454, 184 AA 1230, 156
CEN 3004, 167 Alusuisse Peraluman-260, 224 A91235 UNS (USA) [Aw) ~
Hoogovens 3540, 171 CEN 5454, 185 AA 1235, 156
Hoogovens 3541,171 Hoogovens 5400, 184
A91345 UNS (USA) [Aw) ~
VAW 61/03, 148 A5554 (J) [Aw] ~ AA 1345,157
A3005 (J) [Aw) ~ AA 5554,186
A91350 UNS (USA) [Aw] ~
AA 3005,168 A6061 (Aus) [Aw) ~ AA 1350,157
CEN 3005, 168 AA 6061, 191 Alusuisse Pure Aluminium 99.5 E, 227
VAW61/15,148 CEN 6061, 192 CEN 1350,157
A31D5 (J) [Aw) ~ A6061P (J) [Aw) ~ Hoogovens 1001,151
AA 3105, 170 AA 6061, 191 A92011 UNS (USA) [Aw] ~
CEN 3105, 170 Alusuisse Anticorodal OBO, 216 AA 2011, 159
VAW 61110, 148 Alusuisse Anticorodal-OB2, 216 Alusuisse Decoltal 500, 220
A03330 UNS (USA) [Ac] ~ CEN 6061, 192 CEN 2011, 159
AA 333.0, 237 DIN Wk. 3.3211 (AIMg1SiCu), 145 DIN Wk. 3.1855 (AICuBiPb), 145
A03550 UNS (USA) [Ac) ~ Hoogovens 6560, 198
A92014 UNS (USA) [Aw] ~
AA 355.0, 238 Reynolds R-2000, 227
AA 2014,159
A03560 UNS (USA) [Ac] ~ A6063 (J) [Aw) ~ Alusuisse Avional-660/662, 219
AA 356.0, 239 AA 6060,190 CEN 2014, 160
A03570 UNS (USA) [Ac] ~ AA 6063,193 DIN Wk. 3.1255 (AICuSiMn), 144
AA 357.0, 239 Alunord 6060.4B, 191 Hoogovens 2140, 164
Alunord 6060.79, 191
A03590 UNS (USA) [Ac] ~ A92017 UNS (USA) [Aw] ~
Alusuisse Anticorodal 045/050/053, 216
AA 359.0, 239 AA2017,160
Alusuisse Extrudal-043, 221
A03800 UNS (USA) [Ac) ~ Hoogovens 2170,164
Alusuisse Extrudal-050, 221
AA 3BO.0, 240 BOAl UK AM62, 214 A92024 UNS (USA) [Aw] ~
A4043 (J) [Aw] ~ CEN 6060, 190 AA 2024, 161
AA4043, 172 CEN 6063, 193 Alusuisse Avional150, 219
DIN AI Mg SiO.3, 212 Alusuisse Avional152, 219
A5005 (Aus) [Aw) ~
DIN AI Mg SiO.5, 212 CEN 2024, 162
AA 5005, 174
DIN Wk. 3.3206 (AIMgSiO.5), 145 DIN Wk. 3.1355 (AICuMg2), 144
CEN 5005, 174
NF AGS, 210 Hoogovens 2240, 165
A5005 (J) [Aw) ~ NF A-U4G1, 218
AA 5005, 174 A7020 (J) [Aw) ~
AA 7020,200 A92048 UNS (USA) [Aw] ~
Alusuisse Peraluman-100 (101),223 AA 204B, 163
CEN 5005, 174 Alusuisse Unidur 102, 229
DIN Wk. 3.3315 (AIMg1), 146 CEN 7020, 200 A92124 UNS (USA) [Aw) ~
DIN AI Zn4.5 Mg1, 214 AA 2124, 164
Hoogovens 5010, 174
DIN Wk. 3.4335 (AIZn4.5Mg1), 147 CEN 2124, 164
A5052P (J) [Aw) ~
Hoogovens 7350, 206 A92219 UNS (USA) [Aw] ~
AA 5052, 177
A07070 UNS (USA) [Ac) ~ AA 2219, 165
Alusuisse Peraluman 253, 224
AA 707.0, 244 CEN 2219, 165
CEN 5052, 177
DIN Wk. 3.3523 (AIMg2.5), 146 A7075P (J) [Aw] ~ A92618 UNS (USA) [Aw] ~
Hoogovens 5520, 185 AA 7075,203 AA 261B, 165
VAW 63/52, 148 Alusuisse Perunal 215, 226 A93003 UNS (USA) [Aw] ~
A5D56 (Aus) [Aw) ~ CEN 7075, 204 AA 3003,166
AA 5019, 175 DIN Wk. 3.4365 (AIZnMgCu1.5), 147 AlusuisseAluman 100, 213
CEN 5019, 175 Hoogovens 7750, 207 CEN 3003, 167
A07120 UNS (USA) [Ac) ~ Hoogovens 3530, 170
A5083 (Aus) [Aw) ~
AA 712.0,244 lawson Mardon (lM) Star 3103, 169
AA 50B3, 178
A-47000 CEN (EUR) [Ac) ~ NF 3003, 167
CEN 50B3, 179
DIN GBD-AISi12(Cu), 284 Reynolds Tread-Brite, 228
A5083P (J) [Aw] ~ VAW41/20, 148
AA 50B3, 178 A91050 UNS (USA) [Aw) ~
AA 1050, 151 A93004 UNS (USA) [Aw] ~
Alusuisse Peraluman-460/462, 225
Hoogovens 1000, 151 AA 3004,167
Alusuisse Peraluman-462, 225
CEN 3004, 167
CEN 50B3, 179 VAW 99/52, 149
Hoogovens 3540, 171
Hoogovens 5510, 185 A91060 UNS (USA) [Aw) ~ Hoogovens 3541, 171
Superform Metals 50B3 SPF, 179 AA 1060, 152 VAW 61/03, 148
A5086P (J) [Aw) ~ lawson Mardon (lM) Star 1602, 158
A93005 UNS (USA) [Aw) ~
AA 50B6, 179 A91100 UNS (USA) [Aw] ~ AA 3005,168
Alusuisse Peraluman-41 0/412, 224 AA 1100,154 CEN 3005, 168
CEN 50B6, 180 CEN 1100,154 VAW61/15,148
Hoogovens 5503, 185 A91145 UNS (USA) [Aw] ~
NF A-G4MC, 210 A93103 UNS (USA) [Aw] ~
AA 1145,154
AA 3103, 169
A05140 UNS (USA) [Ac] ~ A91175 UNS (USA) [Aw] ~ CEN 3103, 169
AA 514.0,243 AA 1175, 155 DIN AI Mn1, 213
A05180 UNS (USA) [Ac) ~ A91200 UNS (USA) [Aw] ~ DIN Wk. 3.0315 (AIMn1), 143
AA 51B.0, 243 AA 1200,156 Hoogovens 3000, 166
A05200 UNS (USA) [Ac) ~ Alusuisse Pure Aluminium 99.0, 226 A93105 UNS (USA) [Aw] ~
AA 520.0, 243 CEN 1200, 156 AA 3105, 170
A05350 UNS (USA) [Ac] ~ DIN AI 99, 210 CEN 3105, 170
AA 535.0, 243 Hoogovens 1010, 151 VAW 61/10, 148
A5454 (Aus) [Aw] ~ lawson Mardon (lM) Star 1201,156
A94032 UNS (USA) [Aw) ~
AA 5454, 184 VAW 99/00, 149
AA4032,172
CEN 5454, 185
Alloy Cross-Reference Listing 451
A95005 UNS (USA) [Aw] -+ A96063 UNS (USA) [Aw] -+ AB2 (USA) [Tw] -+
AA 5005, 174 AA 6063, 193 ASTM Grade 5, 333
Alusuisse Peraluman-100 (101), 223 CEN 6063. 193 AB4 (USA) [Tw] -+
CEN 5005, 174 DIN AI Mg SiO.5, 212 Titanium Industries Ti-6-2-4-2, 338
DIN Wk. 3.3315 (AIMg1), 146 A96066 UNS (USA) [Aw] -+ AB13 (Prop.) [Aw]-+
Hoogovens 5010, 174 AA 6066, 193 AA 6012, 189
A95050 UNS (USA) [Aw] -+ A96081 UNS (USA) [Aw] -+ CEN 6012, 189
AA 5050, 176 AA 6081, 194 AB27 (Prop.) [Aw] -+
Alusuisse Peraluman 150/151, 223
A96082 UNS (USA) [Aw] -+ AA 2007, 158
CEN 5050, 176
AA 6082, 194 AC1A.1 (J) [Ac]-+
A95052 UNS (USA) [Aw] -+ Alusuisse Anticorodal 110/112, 217 JIS AC1A (casting), 264
AA 5052, 177 Alusuisse Anticorodal112/114, 217 JIS AC1A.1, 264
Alusuisse Peraluman 253, 224 Alusuisse Anticorodal-1 00/1 05, 216
CEN 5052, 177 AC1A.2 (J) [Ac]-+
BOAl UKAM68, 215
DIN Wk. 3.3523 (AIMg2.5), 146 JIS AC1A (casting), 264
CEN 6082, 195
Hoogovens 5520, 185 DIN AI Mg Si1, 213 AC1B.1 (J) [Ac]-+ J
VAW 63/52, 148 DIN Wk. 3.2315 (AIMgSi1), 145 IS AC1 B (casting), 265
A95056 UNS (USA) [Aw] -+ Hoogovens 6010, 189 AC1 B.2 (J) [Ac] -+
AA 5056,177 NF A-SGMO.7, 218 JIS AC1 B (casting), 265
A95083 UNS (USA) [Aw] -+ A96101 UNS (USA) [Aw] -+ AC2A.1 (J) [Ac]-+
AA 5083, 178 AA 6101, 196 JIS AC2A (casting), 265
Alusuisse Peraluman-460/462, 225 CEN 6101, 196 AC2A.2 (J) [Ac] -+
Alusuisse Peraluman-462, 225 A96151 UNS (USA) [Aw]-+ JIS AC2A (casting), 265
CEN 5083, 179 AA6151,197 AC2B.1 (J) [Ac]-+
Hoogovens 5510, 185
A96162 UNS (USA) [Aw] -+ JIS AC2B (casting), 265
Superform Metals 5083 SPF, 179
AA 6162, 197 AC2B.2 (J) [Ac] -+
A95086 UNS (USA) [Aw] -+
A96201 UNS (USA) [Aw] -+ JIS AC2B (casting), 265
AA 5086,179
AA 6201, 197 AC3A (J) [Ac] -+
Alusuisse Peraluman-41 0/412, 224
A96253 UNS (USA) [Aw] -+ NF A-S12, 258
CEN 5086, 180
Hoogovens 5503, 185 AA 6253, 197 AC3A.1 (J) [Ac]-+
NF A-G4MC, 210 A96262 UNS (USA) [Aw] -+ JIS AC3A (casting), 265
A95154 UNS (USA) [Aw] -+ AA 6262, 197 AC3A.2 (J) [Ac] -+
AA 5154, 181 CEN 6262, 197 JIS AC3A (casting), 265
DIN AIMg3.5, 212 A96351 UNS (USA) [Aw] -+ AC4A (J) [Ac] -+
A95251 UNS (USA) [Aw] -+ AA 6351, 198 NF A-S10G, 258
AA 5251, 182 Alunord 6082-50, 195 Valfond Silafont 36, 288
Alusuisse Peraluman-226, 223 A96951 UNS (USA) [Aw] -+ AC4A.1 (J) [Ac]-+
CEN 5251, 183 AA 6951, 198 JIS AC4A (casting), 265
DIN Wk. 3.3526 (AIMg2MnO.3), 146 A97001 UNS (USA) [Aw] -+ AC4A.2 (J) [Ac] -+
A95252 UNS (USA) [Aw] -+ AA 7001, 199 JIS AC4A (casting), 265
AA 5252, 183 A97009 UNS (USA) [Aw] -+ AC4B.1 (J) [Ac]-+
Alusingen 297, 151 AA 7009, 199 JIS AC4B (casting), 266
Alusuisse Peraluman-875, 226 A97039 UNS (USA) [Aw] -+ AC4B.2 (J) [Ac] -+
A95254 UNS (USA) [Aw] -+ AA 7039,201 JIS AC4B (casting), 266
AA 5254, 183 CEN 7039, 201 AC4C (J) [Ac] -+
A95356 UNS (USA) [Aw] -+ A97049 UNS (USA) [Aw] -+ NF A-S7G03, 257
AA 5356, 184 AA 7049,202 NF A-S7G06, 257
CEN 5356, 184 A97050 UNS (USA) [Aw] -+ AC4C.1 (J) [Ac]-+
A95454 UNS (USA) [Aw] -+ AA 7050,202 JIS AC4C (casting), 266
AA 5454, 184 CEN 7050, 202 AC4C.2 (J) [Ac] -+
Alusuisse Peraluman-260, 224 A97075 UNS (USA) [Aw] -+ JIS AC4C (casting), 266
CEN 5454, 185 AA 7075,203
CEN 5456A, 185 AC4CH.1 (J) [Ac] -+
Alusuisse Perunal 215, 226 JIS AC4CH (casting), 266
Hoogovens 5400, 184 CEN 7075, 204
A95456 UNS (USA) [Aw] -+ AC4CH.2 (J) [Ac] -+
DIN Wk. 3.4365 (AIZnMgCu1.5), 147
AA 5456, 185 JIS AC4CH (casting), 266
Hoogovens 7750, 207
A95457 UNS (USA) [Aw] -+ A97175 UNS (USA) [Aw]-+
AC4D.1 (J) [Ac]-+
AA 5457, 185 JIS AC4D (casting), 266
AA 7175,205
A96003 UNS (USA) [Aw] -+ CEN 7175, 206 AC4D.2 (J) [Ac] -+
AA 6003, 188 JIS AC4D (casting), 266
A9717B UNS (USA) [Aw] -+
A96005 UNS (USA) [Aw] -+ AA 7178,206 AC5A.1 (J) [Ac]-+
AA 6005. 188 CEN 7178, 206 JIS AC5A (casting), 266
Alunord 6081-11. 194 AA 325 Old AA (USA) [Aw] -+ AC5A.2 (J) [Ac] -+
A96053 UNS (USA) [Aw] -+ AA 4032, 172 JIS AC5A (casting), 266
AA 6053,190 AB1 (USA) [Tcw] -+ AC7A.1 (J) [Ac]-+
A96061 UNS (USA) [Aw] -+ Titanium Industries GR-5, 331 JIS AC7A (casting), 267
AA6061,191 AB1 (USA) [Tw] -+ AC7A.2 (J) [Ac]-+
Alusuisse Anticorodal 080, 216 ASTM Grade 5, 333 JIS AC7A (casting), 267
Alusuisse Anticorodal-082, 216 BS 2TA10, 317 ACBA.1 (J) [Ac] -+
CEN 6061, 192 AB2 (ELI) (USA) [Tw] -+ JIS AC8A (casting), 267
DIN Wk. 3.3211 (AIMg1 SiCu), 145 BS 2TA10, 317 ACBA.2 (J) [Ac] -+
Hoogovens 6560, 198
Reynolds R-2000, 227 AB2 (USA) [Tcw] -+ JIS AC8A (casting), 267
Titanium Industries GR-5, 331
452 Alloy Cross-Reference Listing
ACBB.1 (J) [Ae] -+ AC-46000 CEN (EUR) [Ae] -+ AC-AI-Si5Cu3Mn CEN (EUR) [Ae] -+
JIS ACBB (casting), 267 CEN 46000, 252 BS LM4, 285
ACBB.2 (J) [Ae] -+ AC-46100 CEN (EUR) [Ac]-+ CEN 45200, 252
JIS ACBB (casting), 267 CEN 46100,253 AC-AI-Si6Cu4 CEN (EUR) [Ae] -+
ACBC.1 (J) [Ae]-+ UNE L-2640, 284 CEN 45000, 252
JIS ACBC (casting), 267 AC-46200 CEN (EUR) [Ae] -+ DIN GB-AISi6Cu4, 283
ACBC.2 (J) [Ac] -+ CEN 46200, 253 AC-AI-Si7Cu2 CEN (EUR) [Ae] -+
JIS ACBC (casting), 267 DIN GBD-AISi9Cu3, 284 BS LM27, 286
AC9A.1 (J) [Ae] -+ AC-46300 CEN (EUR) [Ae] -+ CEN 46600, 253
JIS AC9A (casting), 267 CEN 46300, 253 AC-AI-Si7Cu3Mg CEN (EUR) [Ae] -+
AC9A.2 (J) [Ae] -+ AC-46400 CEN (EUR) [Ae] -+ CEN 46300, 253
JIS AC9A (casting), 267 CEN 46400, 253 AC-AI-Si7Mg CEN (EUR) [Ae] -+
AC9B.1 (J) [Ae]-+ UN I 7369-74 Part 3, 249 BS LM25, 286
JIS AC9B (casting) 268 AC-46600 CEN (EUR) [Ae] -+ CEN 42000, 250
AC9B.2 (J) [Ae] -+ BS LM27, 286 AC-AI-Si7MgO.3 CEN (EUR) [Ae] -+
JIS AC9B (casting), 268 CEN 46600, 253 CEN 42100, 250
AC-21000 CEN (EUR) [Ae]-+ AC-47000 CEN (EUR) [Ae] -+ AC-AI-Si7MgO.6 CEN (EUR) [Ae] -+
CEN 21000,250 CEN 47000, 253 CEN 42200, 250
AC-21100 CEN (EUR) [Ae] -+ AC-47100 CEN (EUR) [Ae] -+ AC-AI-SiBCu3 CEN (EUR) [Ae] -+
CEN 21100, 250 CEN 47100, 253 CEN 46200, 253
AC-41 000 CEN (EUR) [Ae]-+ AC-4BOOO CEN (EUR) [Ae] -+ DIN GBD-AISi9Cu3, 284
CEN 41000, 250 CEN 4BOOO, 254 AC-AI-Si9 CEN (EUR) [Ae] -+
NF A-S2GT, 256 AC-51000 CEN (EUR) [Ae] -+ CEN 44400, 252
AC-42000 CEN (EUR) [Ae] -+ CEN 51000, 254 AC-AI-Si9Cu1 Mg CEN (EUR) [Ae] -+
BS LM25, 286 DIN GB-AIMg3, 282 CEN 46400, 253
CEN 42000, 250 AC-51100 CEN (EUR) [Ae] -+ UNI 7369-74 Part 3,249
AC-42100 CEN (EUR) [Ae]-+ CEN 51100, 254 AC-AI-Si9Cu3(Fe) CEN (EUR) [Ae] -+
CEN 42100, 250 DIN GB-AIMg3, 282 CEN 46000, 252
AC-42200 CEN (EUR) [Ae] -+ AC-51200 CEN (EUR) [Ae] -+ AC-AI-Si9Mg CEN (EUR) [Ae] -+
CEN 42200, 250 CEN 51200, 254 CEN 43300, 251
DIN GBD-AIMg9, 284 AC-AI-Si10Mg(a) CEN (EUR) [Ae] -+
AC-43000 CEN (EUR) [Ae] -+
AC-51300 CEN (EUR) [Ae]-+ CEN 43000, 251
CEN 43000, 251
DIN GBD-AISi10Mg, 284 CEN 51300, 254 AC-AI-Si10Mg(a) CEN (EUR) [Ae] -+
DIN GB-AIMg5, 283 DIN GBD-AISi10Mg, 284
AC-43100 CEN (EUR) [Ae]-+
CEN 43100, 251 AC-51400 CEN (EUR) [Ae] -+ AC-AI-Si10Mg(b) CEN (EUR) [Ae] -+
DIN GBD-AISi1 OMg, 284 CEN 51400,254 CEN 43100,251
DIN GB-AIMg5Si, 283
AC-43200 CEN (EUR) [Ae] -+ DIN GBD-AISi10Mg, 284
CEN 43200, 251 AC-71000 CEN (EUR) [Ae]-+ AC-AI-Si10Mg(Cu) CEN (EUR) [Ae] -+
DIN GB-AISi1 OMg(Cu), 283 CEN 71000, 254 CEN 43200, 251
NF A-Z5G, 261 DIN GB-AISi1 OMg(Cu), 283
AC-43300 CEN (EUR) [Ae] -+
AC-AICu4MgTi CEN (EUR) [Ae] -+ AC-AI-Si10Mg(Fe) CEN (EUR) [Ae]-+
CEN 43300, 251
CEN 21000,250 CEN 43400, 251
AC-43400 CEN (EUR) [Ae] -+
CEN 43400, 251 AC-AICu4Ti CEN (EUR) [Ae] -+ AC-AI-Si11 CEN (EUR) [Ae] -+
CEN 21100,250 CEN 44000, 251
AC-44000 CEN (EUR) [Ae] -+
AC-AI-Mg3(a) CEN (EUR) [Ae] -+ AC-AI-Si11 Cu2(Fe) CEN (EUR) [Ae] -+
CEN 44000, 251
CEN 51100, 254 CEN 46100, 253
AC-44100 CEN (EUR) [Ae] -+ DIN GB-AIMg3, 282 UNE L-2640, 284
CEN 44100,251
AC-AI-Mg3(b) CEN (EUR) [Ae] -+ AC-AI-Si12(a) CEN (EUR) [Ae] -+
DIN GBD-AISi12, 284
CEN 51000, 254 CEN 44200, 251
AC-44200 CEN (EUR) [Ae] -+ DIN GB-AIMg3, 282 DIN GBD-AISi12, 284
CEN 44200, 251
AC-AI-Mg5 CEN (EUR) [Ae] -+ AC-AI-Si12(b) CEN (EUR) [Ae]-+
DIN GBD-AISi12, 284
CEN 51300, 254 CEN 44100, 251
AC-44300 CEN (EUR) [Ae] -+ DIN GB-AIMg5, 283 DIN GBD-AISi12, 284
CEN 44300, 252
AC-AI-Mg5(Si) CEN (EUR) [Ae] -+ AC-AI-Si12(Cu) CEN (EUR) [Ae] -+
AC-44400 CEN (EUR) [Ae] -+ CEN 51400, 254 DIN GBD-AISi12(Cu), 284
CEN 44400, 252 DIN GB-AIMg5Si, 283 AC-AI-Si12Cu CEN (EUR) [Ae]-+
AC-45000 CEN (EUR) [Ae] -+ AC-AI-Mg9 CEN (EUR) [Ae] -+ CEN 47000, 253
CEN 45000, 252
DIN GB-AISi6Cu4, 283
CEN 51200, 254
DIN GBD-AIMg9, 284
AC-AI-Si12Cu1 (Fe) CEN (EUR) [Ae] -+
CEN 47100,253
AC-45100 CEN (EUR) [Ae]-+ AC-AI-Si2MgTi CEN (EUR) [Ae] -+ AC-AI-Si12CuNiMg CEN (EUR) [Ae] -+
CEN 45100,252 CEN 41000, 250
NF A-S5U3G, 256 CEN 4BOOO, 254
NF A-S2GT, 256
-+ AC-AI-Si12(Fe) CEN (EUR) [Ae] -+
AC-45200 CEN (EUR) [Ae] AC-AI-Si5Cu1 Mg CEN (EUR) [Ae] -+ CEN 44300, 252
BS LM4, 285 BS LM16, 285
CEN 45200, 252 CEN 45300, 252 AC-AI-Zn5Mg CEN (EUR) [Ae] -+
AC-45300 CEN (EUR) [Ae] -+ UNI 3600, 247 CEN 71000, 254
NF A-Z5G, 261
BS LM16, 285 AC-AI-Si5Cu3 CEN (EUR) [Ae] -+
CEN 45300, 252 BS LM22, 286 AD1.1 (J) [Ae]-+
UNI 3600, 247 CEN 45400, 252 JIS AD1.1, 268
AC-45400 CEN (EUR) [Ae] -+ AC-AI-Si5Cu3Mg CEN (EUR) [Ae] -+
JIS ADC1 (casting), 269
BS LM22, 286 CEN 45100, 252 AD1.2 (J) [Ae] -+
CEN 45400, 252 NF A-S5U3G, 256 JIS AD1.2 (ingot), 268
JIS ADC1 (casting), 269
Alloy Cross-Reference Listing 453
AD3.1 (J) [Ac] ~ ADC14 (J) [Ac] ~ A-G2M NF (F) [Aw] ~
JIS AD31. 268 JISAD14.1,269 AA5251,182
JIS ADC3 (casting), 269 JIS AD14.2 (ingot), 269 Alusuisse Peraluman-226, 223
AD3.2 (J) [Ac] ~ JIS ADC14 (casting), 270 CEN 5251, 183
JIS AD3.2 (ingot), 268 AE42 ASTM (USA) [Mc] ~ DIN Wk. 3.3526 (AIMg2Mn03), 146
JIS ADC3 (casting), 269 Hydro Magnesium AE42, 298 A-G2.5C NF (F) [Aw] ~
AD5.1 (J) [Ac] ~ AE42 (Prop.) [Mc] ~ AA 5052,177
JIS AD5.1, 268 Hydro Magnesium AE42. 298 CEN 5052, 177
JIS ADC5 (casting), 269 DIN Wk. 3.3523 (AIMg2.5), 146
A-Fe5 NF (F) [Aw] ~
VAW 63/52, 148
AD5.2 (J) [Ac] ~ AA 8011,207
JIS AD5.2 (ingot), 268 Lawson Mardon (LM) Star 1084, 153 A-G2.5MC NF (F) [Aw] ~
JIS ADC5 (casting), 269 AA 5454, 184
Affimet A-Z1058G (Prop.) [Ac] ~
Alusuisse Peraluman-260, 224
AD6.1 (J) [Ac] ~ Affimet A-Z1 OS8G, 261
CEN 5454, 185
JIS AD6.1, 268 Affimet Calypso 25M (Prop.) [Ac] ~ Hoogovens 5400, 184
JIS ADC6 (casting), 269 AA A206.2, 261
AG 3 NF (F) [Ac] ~
AD6.2 (J) [Ac] ~ Affimet Calypso 43B (Prop.) [Ac] ~ NF AG 3, 270
JIS AD6.2 (ingot), 268 NF A-S 13, 259
JIS ADC6 (casting), 269 A-G3 NF (F) [Aw] ~
Affimet Calypso 43X (Prop.) [Ac] ~ AA 5154, 181
AD10.1 (J) [Ac] ~ NF A-S 13, 259
JISAD10.1,268 AA 5154A, 181
Affimet Calypso 49R (Prop.) [Ac] ~ AA 5454, 184
JIS ADC10 (casting), 269
NF A-S9 Y4, 257 AA 5754, 187
AD10.2 (J) [Ac] ~ Alusingen 234, 150
Affimet Calypso 67B (Prop.) [Ac] ~
JIS AD10.2 (ingot), 268 Alusuisse Peraluman-260, 224
NF A-S7G03, 257
JIS ADC10 (casting), 269 Alusuisse Peraluman-300 (301), 224
Affimet Calypso 67B1 (Prop.) [Ac] ~
AD10Z.1 (J) [Ac] ~ Alusuisse Peraluman-302, 224
NF A-S7G06, 257
JIS AD1 OZ.1, 268 CEN 5154A, 181
Affimet Calypso 67N (Prop.) [Ac] ~
AD12.1 (J) [Ac] ~ CEN 5454, 185
NF A-S7G03, 257
JISADC12 (casting), 269 CEN 5754, 187
Affimet Calypso 67N1 (Prop.) [Ac] ~ DIN AI Mg3 EO, 212
AD12.1 (LME) (J) [Ac] ~
NF A-S7G06, 257 DIN Wk. 3.3535 (AIMg3), 147
JIS AD12.1 (LME), 269
Affimet Calypso 67R (Prop.) [Ac] ~ Hoogovens 5030, 175
AD12.2 (J) [Ac] ~
NF A-S7G03, 257 Hoogovens 5400, 184
JIS AD12.2 (ingot), 269
Affimet Calypso 67R1 (Prop.) [Ac] ~ NF A-G3, 210
JIS ADC12 (casting), 269
NF A-S7G06, 257 AG3C NF (F) [Aw] ~
AD12Z (J) [Ac] ~
Affimet Calypso 675 (Prop.) [Ac] ~ DIN AIMg3.5, 212
JIS AD12Z.1, 269
NF A-S7G03, 257 A-G3M NF (F) [Aw] ~
AD12Z.1 (J) [Ac] ~
Affimet Calypso 6752 (Prop) [Ac] ~ AA 5754, 187
JIS ADC12Z (casting), 269
NF A-S7G03, 257 Alusingen 234, 150
AD14.1 (J) [Ac] ~ Alusuisse Peraluman-300 (301), 224
JIS AD14.1, 269 Affimet Calypso 67XB (Prop.) [Ac] ~
NF A-S7G03, 257 Alusuisse Peraluman-302, 224
JIS ADC14 (casting), 269 CEN 5754, 187
JIS ADC14 (casting), 270 Affimet Calypso 67XB1 (Prop.) [Ac] ~ DIN AI Mg3 EO, 212
AD14.2 (J) [Ac] ~ NF A-S7G06, 257
DIN Wk. 3.3535 (AIMg3), 147
JIS AD14.2 (ingot), 269 Affimet Calypso 69B (Prop.) [Ac] ~ Hoogovens 5030, 175
JIS ADC14 (casting), 270 NF A-S10G, 258 NF A-G3, 210
ADC1 (J) [Ac] ~ Valfond Silafont 36, 288 A-G3T NF (F) [Ac] ~
JIS AD1.1, 268 Affimet Calypso 69N (Prop.) [Ac] ~ AA 511.1, 242
JIS AD1.2 (ingot), 268 NF A-S10G, 258 AA 514.0, 243
JIS ADC1 (casting), 269 Valfond Silafont 36, 288 AA 514.2,243
ADC3 (J) [Ac] ~ Affimet Calypso 82P (Prop.) [Ac] ~ NF A-G3T, 255
JIS AD3.1, 268 NF A-S12UNG, 259 VAWVera1241,291
JIS AD3.2 (ingot), 268 Affimet Calypso 87P (Prop) [Ac] ~ VAW Veral Mg3(H), 291
JIS ADC3 (casting), 269 AA A390.0, 263 VAW Veral Mg3, 291
ADC5 (J) [Ac] ~ A-GO.6 NF (F) [Aw] ~ A-G4MC NF (F) [Aw] ~
JIS AD5.1 , 268 AA 5005, 174 AA 5086,179
JIS AD5.2 (ingot), 268 AA 5005A, 174 Alusuisse Peraluman-41 0/412, 224
JIS ADC5 (casting), 269 Alusingen 214, 150 CEN 5086, 180
ADC6 (J) [Ac] ~ Alusuisse Peraluman-100 (101),223 Hoogovens 5503, 185
JIS AD6.1, 268 CEN 5005, 174 NF A-G4MC, 210
JIS AD6.2 (ingot), 268 DIN AI Mg1, 212 A-G4.5MC NF (F) [Aw] ~
JIS ADC6 (casting) 269 DIN Wk. 3.3315 (AIMg1), 146 AA 5083, 178
ADC10 (J) [Ac] ~ Hoogovens 5010,174 Alusuisse Peraluman-460/462, 225
JIS AD1 0.1, 268 A-G1 NF (F) [Aw] ~ Alusuisse Peraluman-462, 225
JIS AD10.2 (ingot), 268 AA 5050, 176 CEN 5083, 179
JIS ADC10 (casting), 269 Alusuisse Peraluman 150/151, 223 Hoogovens 5510, 185
NF A-S9U3, 258 CEN 5050, 176 Superform Metals 5083 SPF, 179
ADC10Z (J) [Ac] ~ A-G1.5 NF (F) [Aw] ~ A-G5 NF (F) [Aw] ~
JISAD10Z.1,268 AA 5050, 176 AA 5056,177
Alusuisse Peraluman 150/151, 223 AA 5456, 185
ADC12 (J) [Ac] ~
CEN 5050, 176 CEN 5456A, 185
JIS AD12.1 (LME), 269
JIS AD12.2 (ingot), 269 A-G2 NF (F) [Aw] ~
JIS ADC12 (casting), 269 AA 5052, 177
ADC12Z (J) [Ac] ~ CEN 5052, 177
JIS AD12Z.1, 269 DIN Wk. 3.3523 (AIMg2.5), 146
VAW 63/52, 148
454 Alloy Cross-Reference Listing
A-G5M NF (F) [Aw] -+ AIR 9048-620 NF (F) [Aw] -+ AIR Mg1 [Aw] -+
AA5019,175 AA 2214, 164 Alusingen 282, 150
AA 5056, 177 CEN 2214, 164 Alusuisse Refleclal-100, 227
AA 5056A, 178 AIR 9048-630 NF (F) [Aw] -+ A-K2 NF (F) [Ac] -+
AA 5356,184 AA 2024,161 Affimet Calypso 92A, 281
CEN 5019, 175
CEN 5356, 184
Alusuisse Avional 150,219 AK24 (Prop.) [Aw] -+
Alusuisse Avional152, 219 AA 2024, 161
DIN Wk. 3.3555 (AIMg5), 147 CEN 2024, 162 CEN 2024, 162
AG5S NF (F) [Ac] -+ DIN Wk. 3.1355 (AICuMg2), 144
AK60 (Prop) [Aw] -+
NF AG5S, 270 Hoogovens 2240, 165
AA 2219, 165
A-G6 NF (F) [Ac] -+ NF A-U4G1, 218
CEN2219,165
AA 514.0,243 AIR 9048-640 NF (F) [Aw] -+
AI-1Mg VSM (CH) [Aw]-+
NF A-G6, 255 AA2618A,166
AA 5005, 174
A-G6T NF (F) [Ac] -+ CEN 2618A, 166
Alusuisse Peraluman-1 00 (101). 223
AA 535.2, 243 NF A-U2GN, 218
CEN 5005, 174
VAW Veral Mg5(H), 292 AIR 9048-660 NF (F) [Aw] -+ DIN Wk. 3.3315 (AIMg1), 146
VAW Veral Mg5Si(H), 292 AA 6061, 191 Hoogovens 5010. 174
Alusuisse Anticorodal 080, 216
A-G10 NF (F) [Ac]-+ A11.5Mg VSM (CH) [Aw] -+
AA 520.0, 243 Alusuisse Anticorodal-082, 216
AA 5050, 176
NF A-G10, 255 CEN 6061, 192
Alusuisse Peraluman 150/151. 223
A-G10S NF (F) [Ac] -+ DIN Wk. 3.3211 (AIMg1 SiCu), 145
CEN 5050, 176
Hoogovens 6560, 198
AA 518.1, 243
Reynolds R-2000, 227 AI-2Mg VSM (CH) [Aw] -+
VAW Veral Mg9, 292 AA5251,182
A-G10Y4 NF (F) [Ac]-+ AIR 9048-670 NF (F) [Aw] -+
Alusuisse Peraluman-226, 223
AA 520.0, 243 AA 7020,200
CEN 5251.183
Alusuisse Unidur 102, 229
AG-G3 NF (F) [Aw] -+ CEN 7020, 200
DIN Wk. 3.3526 (AIMg2MnO.3), 146
AA 5252, 183 DIN AI Zn4.5 Mg1, 214 AI3.5CuO.5Mg VSM (CH) [Aw] -+
Alusingen 297, 151 AA 2017,160
DIN Wk. 3.4335 (AIZn4.5Mg1), 147
Alusuisse Peraluman-875, 226 Hoogovens 7350, 206 Hoogovens 2170, 164
A-GM4MC NF (F) [Aw] -+ AL21 (Prop) [Aw] -+
AIR 9048-680 NF (F) [Aw] -+
AA 5083,178 AA 7075,203 AA 2091, 163
Alusuisse Peraluman-460/462, 225 Alusuisse Perunal 215, 226 AI 25 (ex USSR) [Ac] -+
Alusuisse Peraluman-462, 225 CEN 7075, 204 GOST AI 25, 272
CEN 5083, 179 DIN Wk. 3.4365 (AIZnMgCu1.5), 147 AI99 DIN (D) [Aw] -+
Hoogovens 5510, 185 Hoogovens 7750, 207 AA 1200, 156
Superform Metals 5083 SPF, 179
AIR 9048-690 NF (F) [Aw] -+ Alusuisse Pure Aluminium 990, 226
AGS (A.G.S) NF (F) [Aw] -+ AA 7075,203 CEN 1200, 156
NF AGS, 210 Alusuisse Perunal 215, 226 DIN A199, 210
A-GS NF (F) [Aw] -+ CEN 7075, 204 Hoogovens 1010, 151
AA 6060, 190 DIN Wk. 3.4365 (AIZnMgCu1.5), 147 lawson Mardon (lM) Star 1201,156
AA 6063,193 Hoogovens 7750, 207 VAW 99/00, 149
Alunord 6060.48, 191 AIR 9048-700 NF (F) [Aw] -+ VAW 99/01, 149
Alunord 6060.79, 191 AA 7075,203 AI99 Onorm (A) [Aw] -+
Alusuisse Anticorodal 045/0501053, 216 Alusuisse Perunal 215, 226 AA 1200.156
Alusuisse Extrudal-043, 221 CEN 7075, 204 Alusuisse Pure Aluminium 99.0, 226
Alusuisse Extrudal-050, 221 DIN Wk. 3.4365 (AIZnMgCu1.5), 147 CEN 1200, 156
BOAl UK AM62, 214 Hoogovens 7750, 207 DIN AI 99, 210
CEN 6060, 190 Hoogovens 1010, 151
AIR 9048-710 NF (F) [Aw]-+
CEN 6063, 193 lawson Mardon (lM) Star 1201. 156
DIN AI Mg SiO.3, 212 AA 7075,203
Alusuisse Perunal 215, 226 VAW 99/00, 149
DIN AI Mg SiO.5, 212 VAW 99/01, 149
CEN 7075, 204
DIN Wk. 3.3206 (AIMgSiO.5), 145 A199; 10842 VSM (CH) [Aw]-+
DIN Wk. 3.4365 (AIZnMgCu1.5), 147
AGS 85 NF (F) [Aw] -+ Hoogovens 7750, 207 AA 1200, 156
Alunord C 50S, 220
AIR 9048-720 NF (F) [Aw] -+ Alusuisse Pure Aluminium 99.0, 226
A-GS/L NF (F) [Aw] -+ AA 7475,206 CEN 1200, 156
AA 6101, 196 CEN 7475, 207 DIN AI 99, 210
CEN6101,196 Hoogovens 1010, 151
DIN E-AI Mg SiO.5, 220 AIR 9048-730 NF (F) [Aw] -+ lawson Mardon (lM) Star 1201, 156
AA 7475,206
A-GSUC NF (F) [Aw] -+ CEN 7475, 207
VAW 99/00, 149
AA 6061, 191 VAW 99/01, 149
AIR 9052 NF (F) [Mw] -+ A199FeO.8 DIN (D) [Aw] -+
Alusuisse Anticorodal 080, 216
Magnesium Elektron Al80, 302 VAW 99/01, 149
Alusuisse Anticorodal-082, 216
CEN 6061, 192 AIR 9052 G-A3Z1 NF (F) [Mw] -+ A199.0 DIN (D) [Aw] -+
DIN Wk. 3.3211 (AIMg1 SiCu), 145 Comeca AZ31 B, 301
AA 1100,154
Hoogovens 6560, 198 Magnesium Elektron Al31, 300 CEN 1100,154
Reynolds R-2000, 227 AIR 9052 G-A6Z1 NF (F) [Mw] -+ A199.0 ISO (EUR) [Aw] -+
AIR 3380 RZ5 NF (F) [Mc] -+ Magnesium Elecktron AZ61, 301 AA 1200, 156
Magnesium Elektron ZE41, 305 AIR 9183 NF (F) [Tcw]-+ Alusuisse Pure Aluminium 99.0. 226
AIR 3380 ZRE1 NF (F) [Mc] -+ NFTA6V,336 CEN 1200, 156
Magnesium Elektron EZ33, 304 AIR G-A9 NF (F) [Mc] -+ DIN AI 99, 210
AIR 9048-610 NF (F) [Aw] -+ ASTM AZ81 A, 302 Hoogovens 1010, 151
AA 2214, 164 AIR MgO.5 [Aw] -+ lawson Mardon (lM) Star 1201, 156
CEN 2214, 164 Alusingen 281, 150 VAW 99/00, 149
Alusuisse Refleclal-050, 227 VAW 99/01, 149
Alloy Cross-Reference Listing 455
A199.0Cu ISO (EUR) [Aw] ~ A199.S DIN (D) [Aw] ~ Alcan 18 (Prop.) [Aw] ~
AA 1100, 154 AA 1060, 152 AA 1050A, 152
CEN 1100,154 AA 1080A, 153 CEN 1050A, 152
A199.5 AECMA (EUR) [Aw] ~ AA1175,155 Alcan 1C (Prop) [Aw] ~
AA 1050, 151 Alusingen 111, 149 AA 1200, 156
Hoogovens 1000, 151 Alusuisse Pure Aluminium 99.8, 227 CEN 1200. 156
VAW 99/52, 149 CEN 1080A, 153
Alcan 1S (Prop.) [Aw] ~
A199.5 DIN (D) [Aw] ~ DIN AI 99.8, 210
AA 1050A, 152
AA 1050, 151 DIN Wk. 3.0285 (AI99.8), 143
CEN 1050A, 152
Lawson Mardon (LM) Star 1602, 158
AA 1050A, 152 DIN AI 99.5, 210
AA 1350, 157 A199.8 ISO (EUR) [Aw] ~
Alcan 2S (Prop.) [Aw] ~
Alusuisse Pure Aluminium 99.5 E, 227 AA 1060, 152
AA 1200, 156
CEN 1050A, 152 AA 1080,153
CEN 1200, 156
CEN 1350, 157 Lawson Mardon (LM) Star 1602, 158 DIN AI 99, 210
Hoogovens 1000, 151 A199.S VSM (CH) [Aw] ~ Alcan 3S (Prop.) [Aw] ~
Hoogovens 1001, 151 AA 1080A, 153
AA 3103, 169
VAW 99/52, 149 Alusingen 111, 149 CEN 3103, 169
A199.5 ISO (EUR) [Aw] ~ Alusuisse Pure Aluminium 99.8, 227 DINAIMn1,213
AA1050, 151 CEN 1080A, 153
DIN AI 99.8, 210 Alcan 05 (Prop.) [Aw] ~
AA 1050A, 152 AA 5083, 178
Alusingen 134, 149 DIN Wk. 3.0285 (AI998), 143
CEN 5083, 179
Alusuisse Pure Aluminium 99.5, 227 AI99.S(A) ISO (EUR) [Aw] ~
CEN 1050A, 152 AA 1080A, 153 Alcan 06 (Prop.) [Aw] ~
DIN AI 99.5, 210 Alusingen 111, 149 AA 5019, 175
DIN Wk. 3.0255 (AI99.5), 143 Alusuisse Pure Aluminium 99.8, 227 AA 5052, 177
Hoogovens 1000, 151 CEN 1080A, 153 AA 5056A, 178
NF A-5, 210 DIN AI 99.8, 210 CEN 5019, 175
NF A-5L, 210 DIN Wk. 30285 (AI998), 143 CEN 5052, 177
VAW 99/52, 149 AI99.S5MgO.5 [Aw] ~ Alcan OS (Prop.) [Aw] ~
AI 99.5 Onorm (A) [Aw] ~ Alusingen 288, 150 AA4032, 172
AA 1050, 151 Alusuisse Peraluman-845, 225 Alcan 11 (Prop.) [Aw] ~
Hoogovens 1000, 151 AI99.85MgO.5Cu [Aw] ~ AA 3003, 166
VAW 99/52, 149 Alusingen 276, 150 CEN 3003, 167
A199.5 VSM (CH) [Aw] ~ Alusuisse Peraluman-843, 225 NF 3003, 167
AA 1050,151 AI99.S5MgO.SCu [Aw] ~ Alcan 15S (Prop.) [Aw] ~
AA 1050A, 152 Alusingen 277, 150 AA 2031, 163
Alusingen 134, 149 Alusuisse Peraluman-853, 225 Alcan 17S (Prop.) [Aw] ~
Alusuisse Pure Aluminium 99.5, 227 AA 2017, 160
A199.85Mg1 [Aw] ~
CEN 1050A, 152 AA 5657, 186 AA 2017A, 161
DIN AI 99.5, 210 CEN2017A,161
Alusingen 278, 150
DIN Wk. 30255 (AI99.5), 143 Alcan 18 (Prop.) [Aw] ~
Alusingen 289, 150
Hoogovens 1000, 151 AA 6463, 198
Alusuisse Peraluman-860, 225
NF A-5, 210
Alusuisse Peraluman-863, 225 Alcan 22 (Prop.) [Aw] ~
NF A-5L, 210
CEN 5657, 186 AA 5251, 182
VAW 99/52, 149
DIN AI 99.85 Mg1, 211 CEN 5251,183
A199.5E UNE (E) [Aw] ~
A199.85Mg1Cu [Aw] ~ Alcan 26S (Prop.) [Aw] ~
AA 1350. 157
AA 5657, 186 AA 2014A, 160
Alusuisse Pure Aluminium 99.5 E, 227
Alusingen 278, 150 Alcan 285 (Prop.) [Aw] ~
CEN 1350, 157
Alusingen 289, 150 AA2011,159
Hoogovens 1001, 151
Alusuisse Peraluman-860, 225 CEN 2011. 159
AI99.5TiO.6 DIN (D) [Aw] ~ Alusuisse Peraluman-863, 225
DIN AI99.5TiO.6, 210 Alcan 33 (Prop.) [Aw] ~
CEN 5657, 186
AA5154A,181
A199.6 ISO (EUR) [Aw] ~ DIN AI 99.85 Mg1, 211
CEN 5154A, 181
AA 1060, 152 AI99.85Mg2.5 [Aw] ~
Lawson Mardon (LM) Star 1602, 158 Alcan 34 (Prop.) [Aw] ~
AA 5252, 183
AA 5454,184
A199.7 DIN (D) [Aw] ~ Alusingen 297, 151
CEN 5454, 185
AA 1070, 152 Alusuisse Peraluman-875, 226
AA 1080A, 153 Alcan 43 (Prop) [Aw] ~
A199.9 [Aw] ~
AA 1175,155 AA 6061, 191
AA 1090,154
Aluslngen 111, 149 CEN 6061, 192
Alusingen 119, 149
Alusuisse Pure Aluminium 99.8, 227 Alusuisse Pure Aluminium 99.9, 227 Alcan 44 (Prop.) [Aw] ~
CEN 1080A, 153 CEN 1090, 154 AA 6082, 194
DIN AI 99.8, 210 DIN AI 99.9, 211 CEN 6082, 195
DIN Wk. 30285 (AI99.8), 143 DIN Wk. 30305 (AI999), 143 Alcan 45 (Prop.) [Aw] ~
Hoogovens 1070, 153 AI99.9MgO.5 [Aw] ~ AA 7017,200
A199.7 ISO (EUR) [Aw] ~ Alusingen 285, 150 AA 7020,200
AA 1070, 152 Alusuisse Remiral-050, 228 CEN 7020, 200
AA 1070A, 153 Alcan 46 (Prop.) [Aw] ~
A199.9Mg1 [Aw] ~
Alunord 1370-70, 158 AA 6063, 193
Alusingen 286, 150
CEN 1070A, 153 CEN 6063, 193
Alusuisse Remiral-100, 228
Hoogovens 1070, 153 Alcan 47E (Prop.) [Aw] ~
Alcan 01 (Prop.) [Aw] ~
AI99.7MgO.SCu [Aw] ~ AA6101A,196
AA2017A,161
AA 5205, 182
CEN 2017A, 161
Alusingen 294, 151
Alusuisse Peraluman-708, 225
456 Alloy Cross-Reference Listing
Alcan 50S (Prop.) [Aw] ~ Alcan C1/DI5 (Prop.) [Aw] ~ Alcan Mg2 (Prop.) [Aw] ~
AA 6063,193 DIN E-AI, 220 AA 5251,182
CEN 6063, 193 Alcan C15 (Prop.) [Aw] ~ CEN 5251, 183
DIN AI Mg SiO.5, 212 AA 1350, 157 Alcan TC37 (Prop.) [Aw] ~
Alcan 515 (Prop.) [Aw] ~ CEN 1350, 157 AA 8091,209
DIN AI Mg SiO.7, 213 Alcan C505, 18 (Prop.) [Aw] ~ Alcan TF41 (Prop.) [Aw] ~
DIN AI Mg SiO.8, 213 AA 6463, 198 AA 4343,173
Alcan 535 (Prop.) [Aw] ~ Alcan C545 (Prop.) [Aw] ~ CEN 4343, 173
AA 5754, 187 AA 5154, 181 AICo2Fe ISO (EUR) [Ac] ~
CEN 5754, 187 Affimet Calypso 92A, 281
Alcan D25 (Prop.) [Aw] ~
DIN AI Mg3 EO, 212
AA 1100,154 Alcoa Alithalite 2090 (Prop.) [Aw] ~
Alcan 545 (Prop.) [Aw] ~ CEN 1100,154 AA 2090,163
AA5154A,181
Alcan D35 (Prop.) [Aw] ~ Alcoa Alithalite 2091 (Prop.) [Aw] ~
CEN 5154A, 181
AA 3003, 166 AA 2091, 163
Alcan 56 (Prop.) [Aw] ~ CEN 3003, 167 Alcoa Alithalite X8090A (Prop.) [Aw] ~
AA 2031, 163 NF 3003, 167 AA X8090A, 231
Alcan 565 (Prop.) [Aw] ~ Alcan D45 (Prop.) [Aw] ~ Alcoa Alithalite X8092 (Prop.) [Aw] ~
AA5019,175 AA 3004, 167 AA X8092, 231
AA 5056A, 178 CEN 3004, 167
CEN 5019, 175 Alcoa Alithalite X8192 (Prop.) [Aw] ~
Alcan D505 (Prop.) [Aw] ~ AA X8192, 231
Alcan 575 (Prop.) [Aw] ~ AA6101A,196
AA 5052, 177 AIFe5i ISO (EUR) [Aw] ~
DIN E-AI Mg SiO.5, 220
CEN 5052, 177 A 8011A, 207
Alcan D545 (Prop.) [Aw] ~ CEN 8011A, 208
Alcan 655 (Prop.) [Aw] ~ AA 5083, 178 DIN Wk. 3.0915 (AIFeSi), 144
AA 6061, 191 CEN 5083, 179
CEN 6061, 192 All Cast Old AA (USA) [Ac] ~
Alcan D745 (Prop.) [Aw] ~ AA 319.0,237
Alcan 66 (Prop) [Aw] ~ DIN AI Zn4.5 Mg1, 214 AA 319.1,237
AA 2014, 159
Alcan Dural 2D (Prop.) [Aw] ~ AA 319.2,237
AA 2014A, 160
AA 7019,200 Allvac 30 (Prop.) [Tw] ~
AA 2214, 164
CEN 2014, 160 Alcan Dural 2E (Prop.) [Aw] ~ Teledyne Allvac 30, 329
CEN 2214, 164 AA 7039,201 Allvac 40 (Prop.) [Tw] ~
CEN 7039, 201 Teledyne Allvac 40, 329
Alcan 725 (Prop.) [Aw] ~
AA 7072,203 Alcan Dural 2X (Prop.) [Aw] ~ Allvac 40+Pd (Prop.) [Tw] ~
CEN 7072, 203 AA 7018,200 Teledyne Allvac 40+Pd, 329
Alcan 74 (Prop.) [Aw] ~ Alcan Dural AD (Prop.) [Aw] ~ Allvac 50 (Prop.) [Tw] ~
AA 7009,199 AA 7050,202 Teledyne Allvac 50,329
CEN 7050, 202
Alcan 755 (Prop.) [Aw] ~ Allvac 55 (Prop.) [Tw] ~
AA 7075,203 Alcan Dural AX (Prop.) [Aw] ~ Teledyne Allvac 55,329
CEN 7075, 204 AA 7150,205 Allvac 6-2-4-2 (Prop.) [Tw] ~
Alcan 77 (Prop.) [Aw] ~ Alcan Dural LE (Prop.) [Aw] ~ Teledyne Allvac 6-2-4-2, 328
AA 7014, 199 AA 7475,206 Allvac 6-2-4-6 (Prop.) [Tw] ~
CEN 7475, 207 Teledyne Allvac 6-2-4-6, 329
Alcan 79 (Prop) [Aw] ~
AA 7079,204 Alcan Dural L T (Prop) [Aw] ~ Allvac 6-4 (Prop.) [Tw] ~
AA 7475,206 Teledyne Allvac 6-4, 329
Alcan 81 (Prop.) [Aw] ~ CEN 7475, 207
AA 7010, 199 Allvac 6-4 ELI (Prop.) [Tw] ~
CEN 7010, 199 Alcan E45 (Prop.) [Aw] ~ Teledyne Allvac 6-4 ELI, 329
AA 3105, 170
Alcan 89 (Prop.) [Aw] ~ CEN 3105,170 Allvac 6-6-2 (Prop.) [Tw] ~
AA 7075,203 Teledyne Allvac 6-6-2, 329
CEN 7075, 204 Alcan E505 (Prop) [Aw] ~
AA 6063A, 193 Allvac 6-7 (Prop.) [Tw] ~
Alcan 99.8% (Prop.) [Aw] ~ DIN AI Mg SiO.5, 212 Teledyne Allvac 6-7, 329
AA 1080A, 153 Allvac 8-1-1 (Prop.) [Tw] ~
CEN 1080A, 153 Alcan E545 (Prop.) [Aw] ~
AA 5086,179 Teledyne Allvac 8-1-1, 329
DIN AI 99.8, 210
CEN 5086, 180 Allvac 70 (Prop.) [Tw] ~
Alcan 623 (Prop.) [Aw] ~ Teledyne Allvac 70,329
AA 6066, 193 Alcan E575 (Prop.) [Aw] ~
DIN AI 99.9 MgO.5, 211 AICu2Mg ISO (EUR) [Aw] ~
Alcan 8265 (Prop.) [Aw] ~ AA 2117,164
AA 2214, 164 Alcan G8385 (Prop.) [Aw] ~
AA 4032, 172 DIN Wk. 3.1305 (AICu2.5MgO.5), 144
CEN 2214, 164 AICu2Mg1.5Fe1Ni1 ISO (EUR) [Aw] ~
Alcan 8355 (Prop.) [Aw] ~ Alcan L575 (Prop) [Aw] ~
AA 2618,165
AA 4045, 172 AA 5657, 186
CEN 5657, 186 AICu2Mg2Ni DIN (D) [Aw] ~
CEN 4045, 172
DIN AI 99.9 Mg1, 211 AA2618,165
Alcan 8515 (Prop.) [Aw] ~
Alcan LlTAL A (Prop) [Aw] ~ AICu2Ni1MgFe5i ISO (EUR) [Aw] ~
AA 6082, 194
AA 8090,209 AA 2031, 163
CEN 6082, 195
DIN AI Mg 5i1, 213 Alcan LlTAL 8 (Prop.) [Aw] ~ AICu25iMn DIN (D) [Aw] ~
AA 8091,209 AA 2038,163
Alcan 8535 (Prop.) [Aw] ~
AA 5454,184 Alcan LlTAL C (Prop.) [Aw] ~ AICu2.5Mg ISO (EUR) [Aw] ~
CEN 5454, 185 AA 8090,209 AA2117,164
Alcan M575 (Prop.) [Aw] ~ DIN Wk. 3.1305 (AICu2.5MgO.5), 144
Alcan 8575 (Prop.) [Aw] ~
AA 5005, 174 AA 5251, 182 AICu2.SMgO.S DIN (D) [Aw] ~
CEN 5005, 174 CEN 5251, 183 AA 2117, 164
DIN AI Mg1, 212 DIN Wk. 3.1305 (AICu2.5MgO.5), 144
Alloy Cross-Reference Listing 457
AICu4Mg1.5 ISO (EUR) [Aw] -+ AICuBiPb DIN (D) [Aw] -+ AIMgO.7Si ISO (EUR) [Aw]-+
AA 2024.161 AA2011,159 AA 6063, 193
Alusuisse Avional 150, 219 Alusuisse Decoltal 500, 220 CEN 6063, 193
Alusuisse Avional152, 219 CEN2011,159 DIN AI Mg SiO.5, 212
CEN 2024, 162 DIN Wk. 3.1855 (AICuBiPb), 145 AIMgO.7Si(A) ISO (EUR) [Aw] -+
DIN Wk. 3.1355 (AICuMg2), 144 AICuMgO.5 Onorm (A) [Aw] -+ AA 6063A, 193
Hoogovens 2240, 165 AA2117,164 AIMgO.7Si(A)i ISO (EUR) [Aw] -+
NF A-U4Gl, 218 DIN Wk. 3.1305 (AICu2.5MgO.5), 144 BaAL UK AM65, 214
AICu4Mg1.5 VSM (CH) [Aw] -+ AICuMg1 DIN (D) [Aw] -+ AIMg1 [Aw] -+
AA 2024,161 AA 2017, 160 AA 5005A, 174
Alusuisse Avional150, 219 AA 2017A, 161 Alusingen 214, 150
Alusuisse Avional152, 219 Alusuisse Avionall 00,218 DIN AI Mgl, 212
CEN 2024, 162 Alusuisse Avional-l 02, 218 AIMg1 DIN (D) [Aw] -+
DIN Wk. 3.1355 (AICuMg2), 144 CEN 2017A, 161 AA 5005,174
Hoogovens 2240, 165 DIN Wk. 3.1325 (AICuMgl), 144 AA 5005A, 174
NF A-U4Gl, 218 Hoogovens 2170, 164 Alusingen 214, 150
AICu4MgSi ISO (EUR) [Aw] -+ NF A-U4G, 218 Alusuisse Peraluman-l00 (101),223
AA 2017, 160 AICuMg1 Onorm (A) [Aw] -+ CEN 5005, 174
Hoogovens 2170,164 AA 2017, 160 DIN AI Mgl, 212
AICu4MgSi(A) ISO (EUR) [Aw] -+ Hoogovens 2170, 164 DIN Wk. 3.3315 (AIMgl), 146
AA 2017A, 161 AICuMg2 DIN (D) [Aw] -+ Hoogovens 5010, 174
Alusuisse Avional 100, 218 AA 2024,161 AIMg1 ISO (EUR) [Aw] -+
Alusuisse Avional-l02, 218 Alusuisse Avional 150, 219 AA 5005, 174
CEN 2017A, 161 Alusuisse Avional 152, 219 Alusuisse Peraluman-l00 (101),223
DIN Wk. 3.1325 (AICuMgl), 144 CEN 2024, 162 CEN 5005, 174
NF A-U4G, 218 DIN Wk. 3.1355 (AICuMg2), 144 DIN Wk. 3.3315 (AIMgl), 146
AICu4MgTi ISO (EUR) [Ac] -+ Hoogovens 2240, 165 Hoogovens 5010, 174
AA 204.2, 234 NF A-U4Gl, 218 AIMg1(B) ISO (EUR) [Aw]-+
CEN 21000, 250 AICuMg2 Onorm (A) [Aw] -+ AA 5005,174
NF A-U5GT, 260 AA2024,161 Alusuisse Peraluman-l00 (101),223
VAW Veral Cu4TiMg, 291 Alusuisse Avional150, 219 CEN 5005, 174
AI-Cu4Ni2Mg2 ISO (EUR) [Ac] -+ Alusuisse Avional152, 219 DIN Wk. 3.3315 (AIMgl), 146
NF A-U4NT, 260 CEN 2024, 162 Hoogovens 5010, 174
AICu4PbMg ISO (EUR) [Aw] -+ DIN Wk. 3.1355 (AICuMg2), 144 AIMg1SiCu ISO (EUR) [Aw]-+
AA 2030,162 Hoogovens 2240, 165 AA 6061, 191
Alusuisse Avional Pb-118, 219 NF A-U4Gl, 218 Alusuisse Anticorodal OBO, 216
CEN 2030, 162 AICuMgPb DIN (D) [Aw] -+ Alusuisse Anticorodal-OB2, 216
NF A-U4PB, 218 AA 2007, 158 CEN 6061, 192
AICu4SiMg ISO (EUR) [Aw] -+ AA 2030,162 DIN Wk. 3.3211 (AIMglSiCu), 145
AA 2014, 159 Alusuisse Avional Pb-llB, 219 Hoogovens 6560, 198
AA 2214,164 CEN 2030, 162 Reynolds R-2000, 227
Alusuisse Avional-660/662, 219 NF A-U4PB, 218 AIMglSiPb ISO (EUR) [Aw] -+
CEN 2014, 160 AICuNi VSM (CH) [Aw] -+ AA 6262,197
CEN 2214, 164 AA 221B, 164 CEN 6262, 197
DIN Wk. 3.1255 (AICuSiMn), 144 AICuSiMn DIN (D) [Aw] -+ AIMg1.5 ISO (EUR) [Aw] -+
Hoogovens 2140, 164 AA 2014, 159 AA 5050, 176
AICu4SiMg(A) ISO (EUR) [Aw] -+ AA 2014A, 160 Alusuisse Peraluman 150/151, 223
AA 2014A, 160 AA 2214,164 CEN 5050, 176
AICu4SiMn VSM (CH) [Aw] -+ Alusuisse Avional-660/662, 219 AIMg1.5(C) ISO (EUR) [Aw]-+
AA 2014A, 160 CEN 2014, 160
AA 5050, 176
CEN 2214, 164
AICu4T ISO (EUR) [Ac] -+ Alusuisse Peraluman 150/151, 223
DIN Wk. 3.1255 (AICuSiMn), 144 CEN 5050, 176
VAW Veral Cu4Ti, 291
DIN Wk. 3.1255 (AICuSiMn), 144
AI-Cu4Ti ISO (EUR) [Ac] -+ Hoogovens 2140, 164 AIMg1.8 DIN (D) [Aw]-+
CEN 21100, 250 AA 5051A, 176
AIFeMg DIN (D) [Aw] -+ CEN 5051A, 176
NF A-U4T, 260
DIN AIFeMg, 212
AICu4TiMg DIN (D) [Ac] -+ DIN AI Mgl.B, 212
AIFeSi DIN (D) [Aw] -+ DIN Wk. 3.3326 (AIMgl.8), 146
AA 295.0, 235
VAW 9B/50, 149 Hoogovens 5020, 175
AI-Cu5NiCo ISO (EUR) [Ac] -+
Alloy No. 234 DIN (D) [Ac] -+ AIMg2 DIN (D) [Aw] -+
NF A-U5NKZr, 260
AA 355.0,238 AA 5052,177
AICu6BiPb ISO (EUR) [Aw] -+
Almag 35 (Prop.) [Ac] -+ Alusuisse Peraluman 253, 224
AA2011,159
AA 535.0, 243 CEN 5052, 177
Alusuisse Decoltal 500, 220
AA 535.2, 243 DIN Wk. 3.3523 (AIMg2.5), 146
CEN 2011, 159
Almag 35 Old AA (USA) [Ac] -+ Hoogovens 5520, 185
DIN Wk. 3.1855 (AICuBiPb), 145
AA 535.0, 243 VAW 63/52, 148
AICu6Mn ISO (EUR) [Aw] -+
AA 535.2, 243 AIMg2 ISO (EUR) [Aw] -+
AA 2219, 165
CEN 2219, 165 AIMgO.5 [Aw] -+ AA 5251, 182
Alusingen 205, 150 Alusuisse Peraluman-226, 223
AI-Cu8Si ISO (EUR) [Ac] -+ CEN 5251, 183
NF A-UBS, 260 Alusuisse Peraluman-050, 223
DIN Wk. 3.3526 (AIMg2MnO.3), 146
AIMgO.5Si ISO (EUR) [Aw] -+
AI-Cu8SiZn ISO (EUR) [Ac] -+ AIMg2MnO.3 DIN (D) [Aw] -+
AA 6063, 193
NF A-U8SZ, 260 AA 5251,182
AA 6063A, 193
BaAL UK AM65, 214 Alusuisse Peraluman-226, 223
CEN 6063, 193 CEN 5251, 183
DIN AI Mg SiO.5, 212 DIN Wk. 3.3526 (AIMg2MnO.3), 146
458 Alloy Cross-Reference Listing
AIMg2MnO.8 DIN (D) [Aw] -+ AIMg3 150 (EUR) [Ac] -+ AIMg4.SMn 150 (EUR) [Aw] -+
AA 5049, 176 AA 511.1, 242 AA 5083,178
Hoogovens3010,168 AA 514.2,243 Alusuisse Alplan, 213
AIMg2.5 DIN (D) [Aw] -+ NF AG 3,270 Alusuisse Peraluman-460/462, 225
AA 5052, 177 NF A-G3T, 255 Alusuisse Peraluman-462, 225
Alusuisse Peraluman 253, 224 VAW Veral 241, 291 CEN 5083, 179
CEN 5052, 177 VAW Veral Mg3(H), 291 Hoogovens 5510, 185
DIN Wk. 3.3523 (AIMg2.5), 146 VAW Veral Mg3, 291 5uperform Metals 5083 5PF, 179
Hoogovens 5520, 185 AA 5754, 187 AIMg4.5Mn V5M (CH) [Aw] -+
VAW 63/52, 148 Alusingen 234, 150 AA 5083, 178
AIMg2.5 150 (EUR) [Aw] -+ Alusuisse Peraluman-300 (301), 224 Alusuisse Peraluman-460/462, 225
AA 5052, 177 Alusuisse Peraluman-302, 224 Alusuisse Peraluman-462, 225
Alusuisse Peraluman 253, 224 CEN 5754, 187 CEN 5083, 179
CEN 5052, 177 DIN AI Mg3 EO, 212 Hoogovens 5510, 185
DIN Wk. 3.3523 (AIMg2.5), 146 DIN Wk. 3.3535 (AIMg3), 147 5uperform Metals 5083 5PF, 179
Hoogovens 5030, 175
Hoogovens 5520, 185 AIMg4.SMnO.4 150 (EUR) [Aw] -+
VAW 63/52, 148 NF A-G3, 210
AA 5182, 181
AIMg2.7Mn DIN (D) [Aw] -+ AIMg3 V5M (CH) [Aw] -+ CEN 5182, 182
AA 5454. 184 AA 5754, 187 VAW 63/45, 148
Alusingen 234, 150
Alusuisse Peraluman-260, 224 AIMg4,SMnO.7 150 (EUR) [Aw] -+
CEN 5454, 185 Alusuisse Peraluman-300 (301), 224
AA 5083, 178
Hoogovens 5400, 184 Alusuisse Peraluman-302, 224
Alusuisse Peraluman-460/462, 225
CEN 5754, 187
AIMg2.7Mn 150 (EUR) [Aw] -+ Alusuisse Peraluman-462, 225
DIN AI Mg3 EO, 212
AA 5454, 184 CEN 5083, 179
DIN Wk. 3.3535 (AIMg3), 147
Alusuisse Peraluman-260, 224 Hoogovens 5510, 185
Hoogovens 5030, 175
CEN 5454, 185 5uperform Metals 5083 5PF, 179
NF A-G3, 210
Hoogovens 5400, 184 AIMg4,5MnO.7(A) 150 (EUR) [Aw] -+
AIMg3Mn 150 (EUR) [Aw] -+
AIMg2.7Mn V5M (CH) [Aw] -+ AA 5454, 184
AA 5183,182
AA 5454, 184 CEN 5183, 182
Alusuisse Peraluman-260, 224
Alusuisse Peraluman-260, 224 CEN 5454, 185 AIMg5 DIN (D) [Ac] -+
CEN 5454, 185 Hoogovens 5400, 184 AA 514.0,243
Hoogovens 5400, 184 AA5019,175
AIMg3Mn(A) 150 (EUR) [Aw] -+
AIMg3 [Aw] -+ AA 5554,186
AA 5056,177
AA 5754, 187 AA 5056A, 178
Alusingen 234, 150 AIMg3Si2 150 (EUR) [Ac] -+ AA 5356, 184
Alusuisse Peraluman-300 (301), 224 AA 512.2,242 AA 5456, 185
Alusuisse Peraluman-302, 224 VAW Veral Mg35i(H), 292 AA 5456A, 185
CEN 5754, 187 AIMg3.5Mn CEN (EUR) [Aw] -+ Alusuisse Peraluman-502, 225
DIN AI Mg3 EO, 212 AA 5042, 176 CEN 5019, 175
DIN Wk. 3.3535 (AIMg3), 147 VAW 63/37, 148 CEN 5356, 184
Hoogovens 5030, 175 AIMg3.5 150 (EUR) [Aw] -+ CEN 5456A, 185
NF A-G3, 210 AA 5154, 181 DIN Wk. 3.3555 (AIMg5), 147
AIMg3 DIN (D) [Ac] -+ AA 51548, 181 AIMgS 150 (EUR) [Aw] -+
AA 5140,243 DIN AIMg3.5, 212 AA 5019, 175
AA 5154, 181 AIMg3.5(A) 150 (EUR) [Aw] -+ AA 5056, 177
AA 5154A, 181 AA5154A,181 AA 5056A, 178
AA 5254, 183 CEN 5154A, 181 AA 5356, 184
CEN 5019, 175
AA 5454,184 AIMg4Mn DIN (D) [Aw] -+
AA 5754. 187 CEN 5356, 184
AA 5086, 179
Alusingen 234, 150 DIN Wk. 3.3555 (AIMg5), 147
Alusuisse Peraluman-41 0/412, 224
Alusuisse Peraluman-260, 224 CEN 5086, 180 AIMg5 Onorm (A) [Aw] -+
Alusuisse Peraluman-300 (301), 224 Hoogovens 5503, 185 AA 5056,177
Alusuisse Peraluman-302, 224 NF A-G4MC, 210 AIMg5Cr 150 (EUR) [Aw] -+
CEN 5154A, 181
AIMg4Mn 150 (EUR) [Aw] -+ AA 5056,177
CEN 5454, 185 AA 5086, 179 AIMg5Cr(A) 150 (EUR) [Aw] -+
CEN 5754, 187 Alusuisse Peraluman-41 0/412, 224 AA 5356,184
DIN AI Mg3 EO, 212 CEN 5356, 184
CEN 5086, 180
DIN AIMg3.5, 212
DIN Wk. 3.3535 (AIMg3), 147
Hoogovens 5503, 185 AIMg5Mn1 150 (EUR) [Aw] -+
NF A-G4MC, 210 AA 5456,185
Hoogovens 5030, 175
Hoogovens 5400, 184 AIMg4Mn V5M (CH) [Aw] -+ AI-MgSS 150 (EUR) [Ac] -+
NF A-G3, 210 AA 5086, 179 NF AG55, 270
Alusuisse Peraluman-41 0/412, 224 AI-Mg5Si1 150 (EUR) [Ac] -+
CEN 5086, 180 AA 514.0,243
Hoogovens 5503, 185 VAW Veral Mg55i(H), 292
NF A-G4MC, 210
AIMg4.5Mn DIN (D) [Aw] -+
AIMg5.2MnCr 150 (EUR) [Aw] -+
AA 5556A, 186
AA 5083, 178
Alusuisse Alplan, 213 AI-Mg6 150 (EUR) [Ae] -+
Alusuisse Peraluman-460/462, 225 AA 514.0,243
Alusuisse Peraluman-462, 225 AA 535.2, 243
Alusuisse Peraluman-470, 225 NF A-G6, 255
CEN 5083, 179 VAW Veral Mg5(H), 292
Hoogovens 5510, 185 AIMg9 DIN (D) [Ac] -+
5uperform Metals 5083 5PF, 179 AA 518.0, 243
AA 535.0, 243
Alloy Cross-Reference Listing 459
AIMg10 DIN (D) [Ac] -+ AIMgSiO.7 VSM (CH) [Aw] -+ AIMgSiPb DIN (D) [Aw] -+
AA 520.0, 243 AA 6005,188 AA 6012, 189
AIMg10 ISO (EUR) [Ac]-+ AA 6005A, 188 Alusuisse Anticorodal Pb-107, 217
AA 51B.2, 243 Alunord 6005A, 188 CEN 6012, 189
AA 520.2, 243 Alunord 60B1-11, 194 AIMn DIN (D) [Aw] -+
NF A-G10, 255 Alusuisse Anticorodal 062, 216 AA 3003, 166
VAW Veral Mg10(H), 292 CEN 6005A, 189 AA 3103,169
VAW Veral Mg9(H), 292 DIN AI Mg SiO.7, 213 Alusuisse Aluman 100, 213
AIMgSi ISO (EUR) [Aw) -+
NF A-SGO.5, 218 CEN 3003, 167
AA 6060,190 AIMgSi1 DIN (D) [Aw] -+ CEN 3103, 169
AA 6063, 193 AA 6003, 188 DIN AI Mn1, 213
AA 6463,198 AA 60B2, 194 Hoogovens 3000, 166
Alunord 6060.4B, 191 Alusuisse Anticorodal 110/112, 217 Hoogovens 3530, 170
Alunord 6060.79, 191 Alusuisse Anticorodal 112/114, 217 lawson Mardon (lM) Star 3103, 169
Alusuisse Anticorodal 045/0501053,216 Alusuisse Anticorodal-1 00/1 05, 216 NF 3003, 167
Alusuisse Extrudal-043, 221 BOAl UK AM6B, 215 Reynolds Tread-Brite, 228
Alusuisse Extrudal-050, 221 CEN 60B2, 195 VAW 41/20, 148
BOAl UKAM62, 214 DIN AI Mg Si1, 213 AIMn VSM (CH) [Aw] -+
CEN 6060, 190 DIN Wk. 3.2315 (AIMgSi1), 145 AA 3003,166
CEN 6063, 193 Hoogovens 6010, 189 AA 3103, 169
DIN AI 99.B5 Mg Si, 211 NF A-SGMO.7, 218 Alusuisse Aluman 100, 213
DIN AI 99.B5 Mg SiO.4, 211 AIMgSi1Cu DIN (D) [Aw] -+ CEN 3003, 167
DIN AI Mg SiO.3, 212 AA 6061, 191 CEN 3103, 169
DIN AI Mg SiO.5, 212 Alusuisse Anticorodal OBO, 216 DIN AI Mn1, 213
DIN AI Mg SiO.5, 212 Alusuisse Anticorodal-OB2, 216 DIN Wk. 3.0315 (AIMn1), 143
DIN Wk. 3.3206 (AIMgSiO.5), 145 CEN 6061, 192 Hoogovens 3000, 166
NF AGS, 210 DIN Wk. 3.3211 (AIMg1SiCu), 145 Hoogovens 3530, 170
AIMgSi VSM (CH) [Aw] -+ Hoogovens 6560, 198 lawson Mardon (lM) Star 3103, 169
AA6101,196 Reynolds R-2000, 227 NF 3003, 167
CEN 6101, 196 AIMgSi1Mn ISO (EUR) [Aw]-+ Reynolds Tread-Brite, 228
AIMgSiO.5 DIN (D) [Aw] -+ AA 60B2, 194 VAW 41/20, 148
AA 6060,190 Alusuisse Anticorodal 110/112, 217 AIMnO.5MgO.5 DIN (D) [Aw] -+
AA 6063,193 Alusuisse Anticorodal 112/114, 217 AA 3105, 170
Alunord 6060.4B, 191 Alusuisse Anticorodal-100/105, 216 CEN 3105, 170
Alunord 6060.79, 191 BOAl UKAM6B, 215 VAW 61/10, 148
Alusuisse Anticorodal 045/050/053, 216 CEN 60B2, 195 AIMnO.5MgO.5 ISO (EUR) [Aw] -+
Alusuisse Extrudal-043, 221 DIN AI Mg Si1, 213 AA 3105, 170
Alusuisse Extrudal-050, 221 DIN Wk. 3.2315 (AIMgSi1), 145 CEN 3105, 170
BOAl UK AM62, 214 Hoogovens 6010, 189 VAW 61110, 148
NF A-SGMO.7, 218
CEN 6060, 190 AIMn1 DIN (D) [Aw] -+
CEN 6063, 193 AIMgSi1 Mn VSM (CH) [Aw] -+ AA 3103, 169
DIN AI Mg SiO.3, 212 AA60B2,194 CEN 3103, 169
DIN AI Mg SiO.5, 212 Alusuisse Anticorodal110/112, 217 DIN AI Mn1, 213
DIN Wk. 3.3206 (AIMgSiO.5), 145 Alusuisse Anticorodal112/114, 217 Hoogovens 3000, 166
NF AGS, 210 Alusuisse Anticorodal-1 00/1 05, 216
AIMn1 ISO (EUR) [Aw] -+
AIMgSiO.5 Onorm (A) [Aw] -+ BOAl UKAM6B, 215
AA 3103, 169
AA 6063, 193 CEN 60B2, 195
CEN 3103, 169
CEN 6063, 193 DIN AI Mg Si1, 213
DIN AI Mn1, 213
DIN AI Mg SiO.5, 212 DIN Wk. 3.2315 (AIMgSi1), 145
DIN Wk. 30315 (AIMn1), 143
AIMgSiO.5 VSM (CH) [Aw] -+ Hoogovens 6010, 189
Hoogovens 3000, 166
AA 6060, 190 NF A-SGMO.7, 218
AIMn1Cr DIN (D) [Aw]-+
Alunord 6060.4B, 191 AIMgSiCu DIN (D) [Aw] -+
VAW41/04,147
Alunord 6060.79, 191 AA 6061,191
Alusuisse Anticorodal OBO, 216 AIMn1Cu DIN (D) [Aw] -+
Alusuisse Anticorodal 045/0501053, 216
Alusuisse Anticorodal-OB2, 216 AA 3003, 166
Alusuisse Extrudal-043, 221
CEN 6061, 192 Alusuisse Aluman 100, 213
Alusuisse Extrudal-050, 221
DIN Wk. 3.3211 (AIMg1SiCu), 145 CEN 3003, 167
BOAl UK AM62, 214
Hoogovens 6560, 198 Hoogovens 3530, 170
CEN 6060, 190
Reynolds R-2000, 227 lawson Mardon (lM) Star 3103, 169
DIN AI Mg SiO.3, 212
NF 3003, 167
DIN AI Mg SiO.5, 212 AIMgSiFe ISO (EUR) [Aw] -+ Reynolds Tread-Brite, 228
DIN Wk. 3.3206 (AIMgSiO.5), 145 AA 6060,190
VAW 41/20, 148
NF AGS, 210 Alunord 6060.4B, 191
Alunord 6060.79, 191 AIMn1Cu ISO (EUR) [Aw]-+
AIMgSiO.7 DIN (D) [Aw]-+
Alusuisse Anticorodal 045/050/053, 216 AA 3003,166
AA 6005,188
Alusuisse Extrudal-043, 221 Alusuisse Aluman 100,213
AA 6005A, 188
Alusuisse Extrudal-050, 221 CEN 3003, 167
Alunord 6005A, 188
BOAl UK AM62, 214 Hoogovens 3530, 170
Alunord 60B1-11, 194
CEN 6060, 190 lawson Mardon (lM) Star 3103, 169
Alusuisse Anticorodal 062, 216
DIN AI Mg SiO.3, 212 NF 3003, 167
CEN 6005A, 189
DIN AI Mg SiO.5, 212 Reynolds Tread-Brite, 228
DIN AI Mg SiO.7, 213
DIN Wk. 3.3206 (AIMgSiO.5), 145 VAW 41/20, 148
NF A-SGO.5, 218
NF AGS, 210
AIMgSiMn ISO (EUR) [Aw] -+
AA6106,196
Alunord 6106, 196
CEN 6106, 196
460 Alloy Cross-Reference Listing
AIMn1Cu NF (F) [Aw] -+ Al-P21 AECMA (EUR) [Aw] -+ AISi6Cu4 DIN (D) [Ac] -+
AA 3003,166 AA 6082, 194 AA 319.0, 237
Alusuisse Aluman 100 213 Alusuisse Anticorodal 110/112 217 AISi6Cu4 ISO (EUR) [Ac] -+
CEN 3003, 167 ' Alusuisse Anticorodal112/114: 217 AAA319.1,262
Hoogovens 3530, 170 Alusuisse Anticorodal-1 00/1 05, 216 NF A-S5UZ, 256
lawson Mardon (lM) Star 3103, 169 BaAL UK AM68, 215 VAW Vera1225, 290
NF 3003, 167 CEN 6082, 195
Reynolds Tread-Brite, 228 DIN AI Mg Si1, 213
AI-Si7Cu3Mg ISO (EUR) [Ac] -+
NF A-S7U3G, 257
VAW 41/20, 148 DIN Wk. 3.2315 (AIMgSi1) 145
Hoogovens6010, 189 AISi7Mg DIN (D) [Ac] -+
AIMn1MgO.S DIN (D) [Aw]-+
NF A-SGMO.7, 218 AA 3560,239
AA 3005,168
AA 357.0, 239
CEN 3005, 168 AL-P22 AECMA (EUR) [Aw] -+
VAW61/15,148 AA 4032, 172 AISi7Mg ISO (EUR) [Ac] -+
AA 356.0, 239
AIMn1MgO.SISO (EUR) [Aw]-+ AL-P31 AECMA (EUR) [Aw] -+
AA A356.2, 262
AA 3005,168 AA 5052, 177
NF A-S7G, 257
CEN 3005, 168 Alusuisse Peraluman 253 224
NF A-S7G03, 257
VAW 61115, 148 CEN 5052, 177 '
NF A-S7G06, 257
AIMn1 MgO.S Clad DIN (D) [Aw] -+ DIN Wk. 3.3523 (AIMg2.5), 146
VAW Pantal 7, 287
AA 3005 Alclad, 168 Hoogovens 5520, 185
VAW 63/52. 148 AISi7Mg(O.2) ISO (EUR) [Ac] -+
Hoogovens 3560 Clad, 171
Affimet Calypso 67R2, 280
AIMn1 Mg1 DIN (D) [Aw] -+ AL-P32 AECMA (EUR) [Aw] -+
AA 5056, 177 AISi7MgO,3 ISO (EUR) [Ac] -+
AA 3004,167
Affimet Calypso 67B. 279
CEN 3004, 167 AL-P42 AECMA (EUR) [Aw] -+
Affimet Calypso 67N, 279
Hoogovens 3540, 171 AA 7075,203
Affimet Calypso 67R, 279
Hoogovens 3541, 171 Alusuisse Perunal 215, 226
Affimet Calypso 67S. 280
VAW 61/03, 148 CEN 7075, 204
Affimet Calypso 67S2, 280
AIMn1 Mg1 ISO (EUR) [Aw] -+ DIN Wk. 3.4365 (AIZnMgCu1.5), 147
Hoogovens 7750, 207 AISi7MgO.6 ISO (EUR) [Ac] -+
AA 3004, 167
Affimet Calypso 67B1, 279
CEN 3004, 167 AISiMg ISO (EUR) [Aw] -+ Affimet Calypso 67N1, 279
Hoogovens 3540, 171 AA 6005, 188
Affimet Calypso 67R1, 279
Hoogovens 3541, 171 Alunord 6081-11, 194
NF A-S7G06, 257
VAW 61/03, 148 AISiMg(A) ISO (EUR) [Aw] -+
AISi8Cu3 DIN (D) [Ac] -+
AIMn1 Mg1 Clad DIN (D) [Aw] -+ AA 6005A, 188 AA 3330,237
AA 3004 Alclad, 168 Alunord 6005A, 188 AA 380.0, 240
Hoogovens 3540 Clad, 171 Alusuisse Anticorodal 062, 216
AISi8Cu3Fe ISO (EUR) [Ac] -+
AIMnCu DIN (D) [Aw] -+ CEN 6005A, 189
DIN AI Mg SiO.7, 213 AA 333/0, 237
AA 3003, 166 AA 380.0, 240
AlusuisseAluman 100, 213 NF A-SGO.5, 218
AA B380.1, 276
CEN 3003. 167 AISiMgO.3 ISO (EUR) [Ac] -+
Hoogovens 3530, 170 NF A-S7G03, 257 AISi8CuFe ISO (EUR) [Ac] -+
VAW VeraI226(0), 290
lawson Mardon (lM) Star 3103.169 AISi1 Mg ISO (EUR) [Aw] -+
NF 3003, 167 AA 6351, 198 AISi9 ISO (EUR) [Ac] -+
Reynolds Tread-Brite, 228 Alunord 6082-50, 195 Affimet Calypso 49R, 278
NF A-S9 Y4, 257
VAW 41120, 148 AISi1MgO.SMn ISO (EUR) [Aw] -+
AIMnCu Clad DIN (D) [Aw] -+ AA 6351, 198 AISi9Cu3 ISO (EUR) [Ac] -+
AA 3003 Alclad, 167 Alunord 6082-50, 195 NF A-S9U3, 258
Hoogovens 3530 Clad, 170 AISi1MgO.8 ISO (EUR) [Aw]-+ AI-Si9Cu3(Fe)(Zn) CEN (EUR) [Ac] -+
AIMnMg ISO (EUR) [Aw] -+ AA 6181, 197 CEN 46500, 253
AA 3105. 170 DIN AI Mg SiO.8, 213 AISi9Cu3FeZn ISO (EUR) [Ac] -+
CEN 3105, 170 AI-Si2MgTi ISO (EUR) [Ac] -+ NF A-S9U3, 258
VAW61/10, 148 NF A-S2GT, 256 AISi9Mg ISO (EUR) [Ac] -+
AL-P12 AECMA (EUR) [Aw]-+ AISiS DIN (D) [Aw] -+ Affimet Calypso 69R, 280
AA 2014, 159 NF A-S9G, 257
AA 4043, 172
Alusuisse Avional-660/662, 219 AA4543,173 AISi9MgCu ISO (EUR) [Ac] -+
CEN 2014, 160 NF A-S9GU, 257
AISiS ISO (EUR) [Aw] -+
DIN Wk. 3.1255 (AICuSiMn), 144
AA 4043, 172 AISi10CuMg ISO (EUR) [Ac] -+
Hoogovens 2140, 164 NF A-S10UG, 258
AA4543, 173
AL-P13 AECMA (EUR) [Aw] -+ AISi10Mg ISO (EUR) [Ac] -+
AA 2024, 161 AISiS(A) ISO (EUR) [Aw] -+
AA 4043A, 172 AA 359.2, 239
Alusuisse Avional 150, 219 Affimet Calypso 69B, 280
Alusuisse Avional152, 219 CEN 4043A, 172
CEN 2024, 162 AISiSCu(Mg) ISO (EUR) [Ac] -+ Affimet Calypso 69S, 281
Affimet Calypso 85R, 281 NF A-S10G, 258
DIN Wk. 3.1355 (AICuMg2), 144 Valfond Silafont 36, 288
Hoogovens 2240, 165 AI-SiSCu1Mg ISO (EUR) [Ac]-+ VAW Silumin-Beta, 288
NF A-U4G1, 218 AA 355.0, 238 VAWVeral Si10MgA, 293
AL-P14 AECMA (EUR) [Aw] -+ AI-SiSCu3 ISO (EUR) [Ac] -+ AISi11 ISO (EUR) [Ac] -+
AA 2117,164 AA 319.0,237 Affimet Calypso 41 R, 278
DIN Wk. 3.1305 (AICu2.5MgO.5), 144 NF A-S5U3, 256 Affimet Calypso 61 S, 279
AI-SiSCu3Mg ISO (EUR) [Ac] -+ AI-Si11CuNiMg ISO (EUR) [Ac]-+
NF A-S5U3G, 256 NF A-S11 UNG, 258
AISiSMg ISO (EUR) [Ac] -+ AISi12 DIN (0) [Aw] -+
NF A-S4G, 256 AA 4047, 173
VAW Pantal 5, 287
VAW Veral Si5MgA, 293
Alloy Cross-Reference Listing 461
AISi12 ISO (EUR) [Ac]-+ Alusingen Alloy No. 234 (Prop.) [Aw] -+ Alusuisse Anticorodal Pb-107 (Prop)[Aw]-+
AA A413.2, 263 Alusingen 234, 150 Alusuisse Anticorodal Pb-107, 217
Affimet Calypso 436, 278 Alusuisse Peraluman-300 (301), 224 Alusuisse Anticorodal Pb-109 (Prop)[Aw]-+
Affimet Calypso 43X, 278 Alusingen Alloy No. 276 (Prop.) [Aw] -+ Alusuisse Anticorodal Pb-109, 217
NF A-S12, 258 Alusingen 276, 150 Alusuisse Avional100 (Prop.) [Aw]-+
VAW Silumin, 288 Alusuisse Peraluman-843, 225 AlusuisseAvional100, 218
VAWVeral Si12A, 293
Alusingen Alloy No. 277 (Prop.) [Aw] -+ Alusuisse Avional-102 (Prop.) [Aw] -+
AISi12 ISO (EUR) [Aw]-+ Alusingen 277, 150 AlusuisseAvional-102,218
AA 4047, 173 Alusuisse Peraluman-853, 225
Alusuisse Avional150 (Prop.) [Aw]-+
AISi12(A) ISO (EUR) [Aw] -+ Alusingen Alloy No. 278 (Prop.) [Aw] -+ Alusuisse Avional150, 219
AA 4047A, 173 Alusingen 278, 150
CEN 4047A, 173 Alusuisse Avional152 (Prop.) [Aw]-+
Alusuisse Peraluman-863, 225
Alusuisse Avional152, 219
AISi12Cu ISO (EUR) [Ac]-+ Alusingen Alloy No. 281 (Prop.) [Aw] -+
NF A-S12U, 259 Alusuisse Avional-660 (Prop.) [Aw] -+
Alusingen 281,150 Alusuisse Avional-660/662, 219
VAW Veral 231A, 290 Alusuisse Reflectal-050, 227
AISi12CuFe ISO (EUR) [Ac] -+ Alusuisse Avional-662 (Prop.) [Aw] -+
Alusingen Alloy No. 282 (Prop.) [Aw] -+ Alusuisse Avional-660/662, 219
AA A413.1, 263 Alusingen 282, 150
VAW Veral 231 (0), 290 Alusuisse Refle'ctal-1 00, 227 Alusuisse Avional Pb-118 (Prop.) [Aw]-+
AISi12CuNiMg ISO (EUR) [Ac]-+ AlusuisseAvional Pb-118, 219
Alusingen Alloy No. 285 (Prop.) [Aw] -+
Affimet Calypso 82P1 , 281 Alusingen 285, 150 Alusuisse Certal (Prop.) [Aw] -+
NF A-S12UNG, 259 Alusuisse Remiral-050, 228 Alusuisse Certal, 220
AISi12Fe ISO (EUR) [Ac] -+ Alusingen Alloy No. 286 (Prop.) [Aw] -+ Alusuisse Contal (Prop.) [Aw] -+
AA A413.1, 263 Alusingen 286, 150 Alusuisse Contal, 220
VAW Veral Si12A(0), 293 Alusuisse Remiral-100, 228 Alusuisse Decoltal500 (Prop.) [Aw] -+
AI-Si13 ISO (EUR) [Ac]-+ Alusingen Alloy No. 288 (Prop.) [Aw] -+ Alusuisse Oecoltal 500, 220
NF A-S13, 259 Alusingen 288, 150 Alusuisse Extrudal-043 (Prop.) [Aw] -+
AISi17Cu4Fe1 Mg ISO (EUR) [Ac] -+ Alusuisse Peraluman-845, 225 Alusuisse Extrudal-043, 221
Valfond A-S17U4G, 259 Alusingen Alloy No. 289 (Prop.) [Aw] -+ Alusuisse Extrudal-050 (Prop.) [Aw] -+
AISi17Cu4Mg ISO (EUR) [Ac]-+ Alusingen 289, 150 Alusuisse Extrudal-050, 221
AA A390.0, 263 Alusuisse Peraluman-860, 225 Alusuisse Peraluman-050 (Prop.) [Aw] -+
Affimet Calypso 87P, 281 Alusingen Alloy No. 294 (Prop.) [Aw] -+ Alusingen 205, 150
AI-Si18CuNiMg ISO (EUR) [Ac]-+ Alusingen 294, 151 Alusuisse Peraluman-050, 223
NF A-S18UNG, 259 Alusuisse Peraluman-708, 225 Alusuisse Peraluman-100 (Prop.) [Aw] -+
AI-Si25CuNiMg ISO (EUR) [Ac] -+ Alusingen Alloy No. 297 (Prop.) [Aw] -+ Alusingen 214, 150
NF A-S25UNG, 260 Alusingen 297, 151 Alusuisse Peraluman-100 (101),223
Alunord 1370-70 (Prop.) [Aw]-+ Alusuisse Peraluman-875, 226 Alusuisse Peraluman 150 (Prop.) [Aw] -+
AA 1070A, 153 Alusuisse Alplan (Prop.) [Aw] -+ Alusuisse Peraluman 150/151, 223
Alunord 1370-70, 158 Alusuisse Alplan, 213 Alusuisse Peraluman 151 (Prop.) [Aw]-+
Alunord 6005A (Prop.) [Aw] -+ Alusuisse Peraluman-470, 225 Alusuisse Peraluman 150/151, 223
Alunord 6005A, 188 Alusuisse Aluman 100 (Am-100) (Prop.) Alusuisse Peraluman-226 (Prop.) [Aw] -+
Alunord 6060 (Prop.) [Aw] -+ [Aw]-+ Alusuisse Peraluman-226, 223
Alunord 6060.48, 191 Alusuisse Aluman 100, 213 Alusuisse Peraluman 253 (Prop.) [Aw] -+
Alunord 6060.79, 191 Alusuisse Anticorodal-041 (Prop.) [Aw] -+ Alusuisse Peraluman 253, 224
Alunord 6081-11 (Prop.) [Aw]-+ Alusuisse Anticorodal-041, 215 Alusuisse Peraluman-260 (Prop.) [Aw]-+
Alunord 6081-11, 194 Alusuisse Anticorodal 045 (Prop.) [Aw] -+ Alusuisse Peraluman-260, 224
Alunord 6082-50 (Prop.) [Aw] -+ Alusuisse Anticorodal 045/0501053, 216 Alusuisse Peraluman-300 (Prop.) [Aw]-+
Alunord 6082-50, 195 Alusuisse Anticorodal 050 (Prop.) [Aw] -+ Alusingen 234, 150
Alunord 6106 (Prop.) [Aw] -+ Alusuisse Anticorodal 045/0501053, 216 Alusuisse Peraluman-300 (301), 224
Alunord 6106, 196 Alusuisse Anticorodal 053 (Prop.) [Aw] -+ Alusuisse Peraluman-302 (Prop.) [Aw] -+
Alunord C50S (Prop.) [Aw] -+ Alusuisse Anticorodal 045/0501053, 216 Alusuisse Peraluman-302, 224
Alunord C 50S, 220 Alusuisse Anticorodal 062 (Prop.) [Aw] -+ Alusuisse Peraluman 410 (Prop.) [Aw]-+
Alusingen Alloy No. 111 (Prop.) [Aw] -+ Alusuisse Anticorodal 062, 216 Alusuisse Peraluman-41 0/412, 224
Alusingen 111, 149 Alusuisse Anticorodal 080 (Prop.) [Aw] -+ Alusuisse Peraluman 460 (Prop.) [Aw] -+
Alusuisse Pure Aluminium 99.8, 227 Alusuisse Anticorodal 080, 216 Alusuisse Peraluman-460/462, 225
Alusingen Alloy No. 119 (Prop.) [Aw]-+ Alusuisse Anticorodal-082 (Prop.) [Aw] -+ Alusuisse Peraluman462 (Prop.) [Aw] -+
Alusingen 119,149 Alusuisse Anticorodal-082, 216 Alusuisse Peraluman-462, 225
Alusuisse Pure Aluminium 99.9, 227 Alusuisse Anticorodal-100 (Prop.) [Aw]-+ Alusuisse Peraluman 470 (Prop.) [Aw] -+
Alusingen Alloy No. 134 (Prop.) [Aw]-+ Alusuisse Anticorodal-1 00/1 05, 216 Alusuisse Alplan, 213
Alusingen 134, 149 Alusuisse Anticorodal-105 (Prop.) [Aw]-+ Alusuisse Peraluman-470, 225
Alusuisse Pure Aluminium 99.5, 227 Alusuisse Anticorodal-100/105, 216 Alusuisse Peraluman-502 (Prop.) [Aw] -+
Alusingen Alloy No. 183 (Prop.) [Aw]-+ Alusuisse Anticorodal110 (Prop.) [Aw]-+ Alusuisse Peraluman-502, 225
Alusingen 183, 150 Alusuisse Anticorodal110/112, 217 Alusuisse Peraluman-708 (Prop.) [Aw] -+
Alusuisse Relital, 227 Alusingen 294, 151
Alusuisse Anticorodal112 (Prop.) [Aw]-+
Alusingen Alloy No. 184 (Prop.) [Aw]-+ Alusuisse Anticorodal 110/112, 217 Alusuisse Peraluman-708, 225
Alusingen 184, 150 Alusuisse Peraluman-843 (Prop.) [Aw] -+
Alusuisse Anticorodal112 (Prop.) [Aw]-+
Alusuisse Pure Aluminium 99.85. 227 Alusingen 276, 150
Alusuisse Anticorodal112/114, 217
Alusingen Alloy No. 205 (Prop.) [Aw] -+ Alusuisse Peraluman-843, 225
Alusuisse Anticorodal114 (Prop.) [Aw]-+
Alusingen 205, 150 Alusuisse Peraluman-845 (Prop.) [Aw] -+
Alusuisse Anticorodal 112/114, 217
Alusuisse Peraluman-050, 223 Alusingen 288, 150
Alusuisse Anticorodal120 (Prop.) [Aw]-+
Alusingen Alloy No. 214 (Prop.) [Aw]-+ Alusuisse Anticorodal120, 217 Alusuisse Peraluman-845, 225
Alusingen 214, 150
Alusuisse Peraluman-100 (101), 223
462 Alloy Cross-Reference Listing
Alusuisse Peraluman-BS3 (Prop.) [Aw] ~ AIZnMgCuO.S DIN (D) [Aw] ~ AIZn6MgCu ISO (EUR) [Aw] ~
Alusingen 277, 150 AA 7022,201 AA 7010, 199
Alusuisse Peraluman-853, 225 AA 7079, 204, 205 Alusuisse Contal, 220
Alusuisse Peraluman-B60 (Prop.) [Aw] ~ Alusuisse Certal, 220 CEN 7010, 199
Alusingen 289, 150 Alusuisse Perunal 205, 226 AIZn6MgCu1.5 ISO (EUR) [Aw] ~
Alusuisse Peraluman-860, 225 Hoogovens 7790, 207 AA 7075,203
Alusuisse Peraluman-B63 (Prop.) [Aw] ~ AIZnMgCu1.S DIN (D) [Aw] ~ Alusuisse Perunal215, 226
Alusingen 278, 150 AA 7075,203 CEN 7075, 204
Alusuisse Peraluman-863, 225 Alusuisse Perunal215, 226 DIN Wk. 3.4365 (AIZnMgCu1.5), 147
Alusuisse Peraluman-B7S (Prop) [Aw] ~ CEN 7075, 204 Hoogovens 7750, 207
Alusingen 297, 151 DIN Wk. 3.4365 (AIZnMgCu1.5), 147 AIZn6MgCu1.S VSM (CH) [Aw] ~
Alusuisse Peraluman-875, 226 Hoogovens 7750, 207 AA 7075,203
Alusuisse Perunal 20S (Prop.) [Aw] ~ AIZnMgCu1.S bnorm (A) [Aw] ~ Alusuisse Perunal 215, 226
Alusuisse Perunal 205, 226 AA 7075,203 CEN 7075, 204
Alusuisse Perunal215, 226 DIN Wk. 3.4365 (AIZnMgCu1.5), 147
Alusuisse Perunal21S (Prop.) [Aw] ~ CEN 7075, 204 Hoogovens 7750, 207
Alusuisse Perunal215, 226 DIN Wk. 3.4365 (AIZnMgCu1.5), 147 AIZn7MgCu DIN (D) [Aw] ~
Alusuisse Perunal 232 (Prop.) [Aw] ~ Hoogovens 7750, 207 Alusuisse Perunal 232, 226
Alusuisse Perunal 232, 226 AIZnMnCu VSM (CH) [Aw] ~ AIZn7MgCu ISO (EUR) [Aw] ~
Alusuisse Perunal 249 (Prop.) [Aw] ~ AA 7075,203 AA 7178,206
Alusuisse Perunal 249, 226 Alusuisse Perunal215, 226 CEN 7178, 206
Alusuisse Pure Aluminium 99.0 (Prop.) CEN 7075, 204
AIZnBMgCu1.5 DIN (D) [Aw] ~
[Aw]~ DIN Wk. 3.4365 (AIZnMgCu1.5), 147
AA 7049A, 202
Alusuisse Pure Aluminium 99.0, 226 Hoogovens 7750, 207
Alusuisse Perunal 249, 226
Alusuisse Pure Aluminium 99.S (Prop.) AIZnMnCu-pl VSM (CH) [Aw] ~ CEN 7049A, 202
[Aw]~ AA 7075 Alclad, 204
AIZnBMgCu ISO (EUR) [Aw] ~
Alusingen 134, 149 AIZn1 ISO (EUR) [Aw] ~ AA 7049A, 202
Alusuisse Pure Aluminium 99.5, 227 AA 7072,203 Alusuisse Perunal 249, 226
Alusuisse Pure Aluminium 99.S E (Prop.) CEN 7072, 203 CEN 7049A, 202
[Aw]~ AIZn4MgO.B DIN (D) [Aw] ~ AIZn10SiB ISO (EUR) [Ae] ~
Alusuisse Pure Aluminium 99.5 E, 227 AA 7027,201 NF Unifont, 289
Alusuisse Pure Aluminium 99.B (Prop.) Alusuisse Unidur 091, 229
AM NF (F) [Aw] ~
[Aw]~ AIZn4Mg2 DIN (D) [Aw] ~ DIN AI Mn1, 213
Alusingen 111, 149 Alusuisse Unidal, 228
Alusuisse Pure Aluminium 99.8, 227 A-M1 NF (F) [Aw] ~
AIZn4.SMg1 DIN (D) [Aw] ~ AA 3003,166
Alusuisse Pure Aluminium 99.BS (Prop.) AA 7020,200 AA 3103, 169
[Aw]~ Alusuisse Unidur 102, 229 Alusuisse Aluman 100, 213
Alusingen 184, 150 CEN 7020, 200 CEN 3003, 167
Alusuisse Pure Aluminium 99.85, 227 DIN AI Zn4.5 Mg1, 214 CEN 3103, 169
Alusuisse Pure Aluminium 99.9 (Prop.) DIN Wk. 3.4335 (AIZn4.5Mg1), 147 DIN AI Mn1, 213
[Aw]~ Hoogovens 7350, 206 DIN Wk. 3.0315 (AIMn1), 143
Alusingen 119, 149 AIZn4.SMg1 ISO (EUR) [Aw] ~ Hoogovens 3000, 166
Alusuisse Pure Aluminium 99.9, 227 AA 7020,200 Hoogovens 3530, 170
Alusuisse Reflectal-OSO (Prop.) [Aw] ~ Alusuisse Unidur 102, 229 Lawson Mardon (LM) Star 3103, 169
Alusingen 281, 150 CEN 7020, 200 NF 3003, 167
Alusuisse Reflectal-050, 227 DIN AI Zn4.5 Mg1, 214 Reynolds Tread-Brite, 228
Alusuisse Reflectal-100 (Prop.) [Aw] ~ DIN Wk. 3.4335 (AIZn4.5Mg1), 147 VAW 41/20, 148
Alusingen 282, 150 Hoogovens 7350, 206 A-M1G NF (F) [Aw] ~
Alusuisse Reflectal-100, 227 AIZn4.SMg1 VSM (CH) [Aw] ~ AA 3004,167
Alusuisse Relital (Prop.) [Aw] ~ AA 7020,200 CEN 3004, 167
Alusingen 183, 150 Alusuisse Unidur 102, 229 Hoogovens 3540, 171
Alusuisse Relital, 227 CEN 7020, 200 Hoogovens 3541,171
DIN AI Zn4.5 Mg1, 214 VAW 61/03, 148
Alusuisse Remiral-OSO (Prop.) [Aw] ~
DIN Wk. 3.4335 (AIZn4.5Mg1), 147 AM10 (Prop.) [Aw] ~
Alusingen 285, 150
Hoogovens 7350, 206 AA 5005A, 174
Alusuisse Remiral-050, 228
AIZn4.SMg1.SMn ISO (EUR) [Aw] ~ AM15 (Prop.) [Aw] ~
Alusuisse Remiral-100 (Prop.) [Aw] ~
AA 7005,199 AA 5050B, 176
Alusingen 286, 150
Alusuisse Remiral-100, 228 AI-ZnSMg ISO (EUR) [Ae] ~ AM1B (Prop.) [Aw] ~
NF A-Z5G, 261 AA 5051A, 176
Alusuisse Unidal (Prop.) [Aw] ~
Alusuisse Unidal, 228 AIZnSMg1.S DIN (D) [Aw] ~ CEN 5051A, 176
AA 7018,200 AM20 ASTM (USA) [Me] ~
Alusuisse Unidur 091 (Prop.) [Aw] ~
Alusuisse Unidur 120,229 ASTM AM20, 298
Alusuisse Unidur 091, 229
AIZnS.5MgCu ISO (EUR) [Aw] ~ Hydro Magnesium AM20, 298
Alusuisse Unidur 102 (Prop.) [Aw] ~
AA 7075,203 AM20 (Prop.) [Me] ~
Alusuisse Unidur 102, 229
Alusuisse Perunal 215, 226 Hydro Magnesium AM20, 298
Alusuisse Unidur 120 (Prop.) [Aw] ~ CEN 7075, 204
Alusuisse Unidur 120, 229 AM21 (Prop.) [Aw] ~
DIN Wk. 3.4365 (AIZnMgCu1.5), 147 AA 5049,176
ALV64 DIN (D) [Tw] ~ Hoogovens 7750, 207 CEN5049, 176
Titanium IntI. Ti-64, 339 AIZn5.SMgCu(A) ISO (EUR) [Aw] ~ AMSOA ASTM (USA) [Me] ~
AIZnMg1 DIN (D) [Aw] ~ AA 7475,206 ASTM AM50A, 298
AA 7005, 199 CEN 7475, 207
AMSOB ASTM (USA) [Me] ~
AIZn6CuMgZr ISO (EUR) [Aw] ~ ASTM AM50B, 298
AA 7050,202
CEN 7050, 202
Alloy Cross-Reference Listing 463
ASG NF (F) [Aw] -+ A-U4N NF (F) [Aw] -+ AW-1090 CEN (EUR) [Aw]-+
AA 6005, 188 AA 2218, 164 AA 1090, 154
AA6181,197 A-U4NT NF (F) [Ac] -+ Alusingen 119, 149
Alunord 6081-11,194 NF A-U4NT, 260 Alusuisse Pure Aluminium 99.9, 227
CEN 6005A, 189
A-U4Pb NF (F) [Aw] -+ CEN 1090, 154
DIN AI Mg SiO.8, 213 DIN AI 99.9, 211
AA 2030,162
A-SGO.5 NF (F) [Aw] -+ Alusuisse Avional Pb-118, 219 DIN Wk. 3.0305 (AI99.9), 143
AA 6005A, 188 CEN 2030, 162 AW-1100 CEN (EUR) [Aw]-+
Alunord 6005A, 188 NF A-U4PB, 218 AA 1100, 154
Alusuisse Anticorodal 062, 216
A-U4SG NF (F) [Aw] -+ CEN 1100,154
DIN AI Mg SiO.7, 213 AW-1198 CEN (EUR) [Aw]-+
AA 2014, 159
NF A-SGO.5, 218 AA 1198, 155
AA 2014A, 160
A-SGM NF (F) [Aw] -+ Alusuisse Avional-660/662, 219 CEN 1198, 155
AA 6003,188 CEN 2014, 160 AW-1199 CEN (EUR) [Aw]-+
AA 6082, 194 DIN Wk. 3.1255 (AICuSiMn), 144 AA 1199,155
Alusuisse Anticorodal 110/112 217 Hoogovens 2140, 164 CEN 1199, 155
Alusuisse Anticorodal 112/114' 217
A-U4T NF (F) [Ac] -+ AW-1200 CEN (EUR) [Aw]-+
Alusuisse Anticorodal-1 00/1 05', 216
NF A-U4T, 260 AA 1200, 156
BOAl UK AM68, 215
CEN 6082, 195 A-U5GT (Prop.) [Ac] -+ Alusuisse Pure Aluminium 99.0, 226
AA 204.0, 234 CEN 1200, 156
DIN AI Mg Si1, 213
AA 204.2, 234 DIN AI 99, 210
DIN Wk. 3.2315 (AIMgSi1), 145
Hoogovens 6010, 189 A-U5GT NF (F) [Ac] -+ Hoogovens 1010,151
AA 204.0, 234 lawson Mardon (lM) Star 1201, 156
NF A-5GMO.7, 218
VAW 99/00, 149
A-SGMO.3 NF (F) [Aw] -+ AA 204.2, 234
AA 6081,194 NF A-U5GT, 260 AW-1350 CEN (EUR) [Aw] -+
VAW Veral Cu4TiMg, 291 AA 1350, 157
A-SGMO.7 NF (F) [Aw] -+
AA 6082, 194 A-U5NKZr NF (F) [Ac] -+ Alusuisse Pure Aluminium 99.5 E, 227
NF A-U5NKZr, 260 CEN 1350, 157
Alusuisse Anticorodal110/112, 217 Hoogovens 1001, 151
Alusuisse Anticorodal112/114, 217 A-U5PbBi NF (F) [Aw] -+
AA2011,159 AW-1370 CEN (EUR) [Aw] -+
Alusuisse Anticorodal-100/105, 216
Alusuisse Decoltal 500, 220 AA 1370, 157
BOAl UK AM68, 215
CEN2011,159 CEN 1370,157
CEN 6082, 195
DIN AI Mg Si1, 213 DIN Wk. 3.1855 (AICuBiPb), 145 AW-2011 CEN (EUR) [Aw]-+
AA2011,159
DIN Wk. 3.2315 (AIMgSi1), 145 A-U6MT NF (F) [Aw] -+
Hoogovens 6010, 189 AA2219,165 Alusuisse Decoltal 500, 220
NF A-SGMO.7, 218 CEN 2219, 165 CEN 2011, 159
DIN Wk. 3.1855 (AICuBiPb), 145
ATI 24 (S) [Tw] -+ A-U8S NF (F) [Ac] -+
Titanium IntI. Ti-1, 337 AW-2011A CEN (EUR) [Aw] -+
NF A-U8S, 260
AA 2011A, 159
ATI 30 (5) [Tw] -+ A-U8SZ NF (F) [Ac] -+ CEN 2011A, 159
Titanium IntI. Ti-2, 337 NF A-U8SZ, 260
AW-2014 CEN (EUR) [Aw] -+
ATI 30-Pd (S) [Tw] -+ A-USG7 NF (F) [Ac]-+ AA2014,159
Titanium IntI. Ti-7, 338 AA 295.0,235 Alusuisse Avional-660/662, 219
ATI 35 (S) [Tw]-+ AW-1050A CEN (EUR) [Aw]-+ CEN 2014, 160
Titanium IntI. Ti-3, 337 AA 1050, 151 DIN Wk. 3.1255 (AICuSiMn), 144
ATI45 (5) [Tw] -+ AA 1050A, 152 Hoogovens 2140, 164
Titanium IntI. Ti-4, 337 Alusingen 134, 149 AW-2014A CEN (EUR) [Aw] -+
A-U2G NF (F) [Aw] -+ Alusuisse Pure Aluminium 99.5, 227 AA 2014A, 160
AA2117,164 CEN 1050A, 152
AW-2017A CEN (EUR) [Aw]-+
DIN Wk. 3.1305 (AICu2.5MgO.5), 144 DIN AI 99.5, 210
AA 2017A, 161
DIN Wk. 30255 (AI99.5), 143
A-U2GN NF (F) [Aw] -+ AlusuisseAvional100,218
Hoogovens 1000, 151
AA 2618, 165 Alusuisse Avional-102, 218
NF A-5, 210
AA 2618A, 166 CEN 2017A, 161
NF A-5l, 210
CEN 2618A, 166 DIN Wk. 3.1325 (AICuMg1), 144
VAW 99/52, 149
NF A-U2GN, 218 NF A-U4G, 218
AW-1070A CEN (EUR) [Aw]-+
A-U2N NF (F) [Aw] -+ AW-2024 CEN (EUR) [Aw] -+
AA 1070A, 153
AA2031,163 AA 2024,161
Alunord 1370-70, 158
A-U4G NF (F) [Aw] -+ CEN 1070A, 153
AlusuisseAvional 150, 219
AA 2017, 160 Alusuisse Avional152, 219
AW-1080A CEN (EUR) [Aw]-+ CEN 2024, 162
AA 2017A, 161
AA 1080A, 153 DIN Wk. 3.1355 (AICuMg2), 144
Alusuisse Avional100, 218
Alusingen 111, 149 Hoogovens 2240, 165
Alusuisse Avional-102, 218 Alusuisse Pure Aluminium 99.8, 227
CEN 2017A, 161 NF A-U4G1, 218
CEN 1080A, 153
DIN Wk. 3.1325 (AICuMg1), 144 AW-2030 CEN (EUR) [Aw] -+
DIN AI 99.8, 210
Hoogovens 2170, 164 AA 2030, 162
DIN Wk. 3.0285 (AI99.8), 143
NF A-U4G, 218 Alusuisse Avional Pb-118, 219
AW-1085 CEN (EUR) [Aw]-+
A-U4G1 NF (F) [Aw] -+ CEN 2030, 162
AA 1085, 153
AA 2024,161 AW-2124 CEN (EUR) [Aw] -+
Alusingen 184, 150
Alusuisse Avional150, 219 AA 2124, 164
Alusuisse Pure Aluminium 99.85, 227
Alusuisse Avional152, 219 CEN 2124, 164
CEN 1085, 153
CEN 2024, 162
DIN AI 99.85, 211 AW-2214 CEN (EUR) [Aw] -+
DIN Wk. 3.1355 (AICuMg2), 144 AA 2214, 164
Hoogovens 2240, 165 CEN 2214, 164
NF A-U4G1, 218
Alloy Cross-Reference Listing 465
AW-2219 CEN (EUR) [Aw] ~ AW-S019 CEN (EUR) [Aw] ~ AW-5S57 CEN (EUR) [Aw] ~
AA 2219, 165 AA 5019, 175 AA 5657,186
CEN 2219, 165 AA 5056A, 178 Alusingen 278, 150
AW-2S18A CEN (EUR) [Aw] ~ CEN 5019, 175 Alusingen 289, 150
AA 2618A, 166 DIN Wk. 3.3555 (AIMg5), 147 Alusuisse Peraluman-860, 225
CEN 2618A, 166 AW-S042 CEN (EUR) [Aw] ~ Alusuisse Peraluman-863, 225
NF A-U2GN, 218 AA 5042,176 CEN 5657, 186
AW-3003 CEN (EUR) [Aw] ~ VAW 63/37, 148 DIN AI 99.85 Mg1, 211
AA 3003,166 AW-5049 CEN (EUR) [Aw] ~ AW-5754 CEN (EUR) [Aw] ~
AlusuisseAluman 100, 213 AA 5049, 176 AA 5754,187
CEN 3003, 167 AW-SOSO CEN (EUR) [Aw] ~
Alusingen 234, 150
Hoogovens 3530, 170 AA 5050,176 Alusuisse Peraluman-300 (301),224
lawson Mardon (lM) Star 3103, 169 Alusuisse Peraluman 150/151, 223 Alusuisse Peraluman-302, 224
NF 3003, 167 CEN 5050, 176 CEN 5754, 187
Reynolds Tread-Brite, 228 DIN AI Mg3 EQ, 212
AW-50S1 A CEN (EUR) [Aw] ~ DIN Wk. 3.3535 (AIMg3), 147
VAW 41/20, 148
AA 5051A, 176 Hoogovens 5030, 175
AA 3004,167
CEN 5051A, 176 NF A-G3, 210
CEN 3004, 167
DIN AI Mg1.8, 212
Hoogovens 3540, 171 AW-SOOSA CEN (EUR) [Aw] ~
DIN Wk. 3.3326 (AIMg1.8), 146
Hoogovens 3541, 171 AA 6005A, 188
VAW 61/03, 148 AW-SOS2 CEN (EUR) [Aw] ~ Alunord 6005A, 188
AA 5052, 177 Alusuisse Anticorodal 062, 216
AW-3005 CEN (EUR) [Aw] ~
Alusuisse Peraluman 253, 224 CEN 6005A, 189
AA 3005,168
CEN 5052, 177 DIN AI Mg SiO.7, 213
CEN 3005, 168
DIN Wk. 3.3523 (AIMg2.5), 146 NF A-SGO.5, 218
VAW61/15,148
Hoogovens 5520, 185
AW-3103 CEN (EUR) [Aw] ~ AW-S012 CEN (EUR) [Aw] ~
VAW 63/52, 148
AA 3103, 169 AA 6012, 189
AW-S05SA CEN (EUR) [Aw] ~ Alusuisse Anticorodal Pb-107, 217
CEN 3103, 169
AA 5056A, 178 CEN 6012, 189
DIN AI Mn1, 213
DIN Wk. 3.3555 (AIMg5), 147
DIN Wk. 3.0315 (AIMn1), 143 AW-S018 CEN (EUR) [Aw] ~
Hoogovens 3000, 166 AW-S083 CEN (EUR) [Aw] ~ AA 6018, 190
AA 5083,178 Alusuisse Anticorodal Pb-109, 217
AW-3104 CEN (EUR) [Aw] ~
Alusuisse Peraluman-460/462, 225
AA 3104, 169 AW-SOSS CEN (EUR) [Aw] ~
Alusuisse Peraluman-462, 225
CEN 3104, 169 AA 6056,190
CEN 5083, 179
AW-3105 CEN (EUR) [Aw] ~ Hoogovens 5510, 185 CEN 6056, 190
AA 3105, 170 Superform Metals 5083 SPF, 179 AW-SOSO CEN (EUR) [Aw] ~
CEN 3105, 170 AA 6060, 190
AW-508S CEN (EUR) [Aw] ~
VAW 61/10, 148 Alunord 6060.48, 191
AA 5086,179
AW-4004 CEN (EUR) [Aw] ~ Alusuisse Peraluman-41 0/412, 224 Alunord 6060.79, 191
AA 4004, 171 CEN 5086, 180 Alusuisse Anticorodal 045/050/053, 216
CEN 4004, 171 Hoogovens 5503, 185 Alusuisse Extrudal-043, 221
AW-400S CEN (EUR) [Aw] ~ NF A-G4MC, 210 Alusuisse Extrudal-050, 221
AA 4006, 171 BOAl UK AM62, 214
AW-S087 CEN (EUR) [Aw] ~ CEN 6060, 190
CEN 4006, 171 AA 5087,180 DIN AI Mg SiO.3, 212
AW-4007 CEN (EUR) [Aw] ~ CEN 5087, 180 DIN AI Mg SiO.5, 212
AA4007, 171 AW-S154A CEN (EUR) [Aw] ~ DIN Wk. 3.3206 (AIMgSiO.5), 145
CEN 4007, 171 AA 5154A, 181 NF AGS, 210
AW-4043A CEN (EUR) [Aw] ~ CEN 5154A, 181 AW-SOS1 CEN (EUR) [Aw] ~
AA 4043A, 172 AW-S182 CEN (EUR) [Aw] ~ AA 6061,191
CEN 4043A, 172 AA 5182, 181 Alusuisse Anticorodal 080, 216
AW-4045 CEN (EUR) [Aw] ~ CEN 5182, 182 Alusuisse Anticorodal-082, 216
AA4045,172 VAW 63/45, 148 CEN 6061, 192
CEN 4045, 172 AW-5183 CEN (EUR) [Aw] ~ DIN Wk. 3.3211 (AIMg1SiCu), 145
AW-4047A CEN (EUR) [Aw] ~ AA 5183, 182 Hoogovens 6560, 198
AA 4047A, 173 CEN 5183, 182 Reynolds R-2000, 227
CEN 4047A, 173 AW-5251 CEN (EUR) [Aw] ~ AW-SOS3 CEN (EUR) [Aw] ~
AW-4104 CEN (EUR) [Aw] ~ AA 5251,182 AA6063, 193
AA 4104,173 Alusuisse Peraluman-226, 223 CEN 6063, 193
CEN 4104,173 CEN 5251, 183 DIN AI Mg SiO.5, 212
AW-4343 CEN (EUR) [Aw] ~ DIN Wk. 3.3526 (AIMg2MnO.3), 146 AW-S081 CEN (EUR) [Aw] ~
AA 4343,173 AW-S35S CEN (EUR) [Aw] ~ AA 6081,194
CEN 4343, 173 AA 5356,184 AW-S082 CEN (EUR) [Aw] ~
AW-5005 CEN (EUR) [Aw] ~ CEN 5356, 184 AA 6082,194
AA 5005,174 AW-5454 CEN (EUR) [Aw] ~ Alusuisse Anticorodal110/112, 217
Alusuisse Peraluman-100 (101),223 AA 5454, 184 Alusuisse Anticorodal112/114, 217
CEN 5005, 174 Alusuisse Peraluman-260, 224 Alusuisse Anticorodal-1 00/1 05, 216
DIN Wk. 3.3315 (AIMg1), 146 CEN 5454, 185 BOAl UK AM68, 215
Hoogovens 5010, 174 Hoogovens 5400, 184 CEN 6082, 195
AW-S010 CEN (EUR) [Aw] ~ AW-S4SSA CEN (EUR) [Aw] ~ DIN AI Mg Si1, 213
AA 5010, 174 AA 5456A, 185 DIN Wk. 3.2315 (AIMgSi1), 145
Alusuisse Peraluman-502, 225 Hoogovens 6010, 189
CEN 5456A, 185 NF A-SGMO.7, 218
AW-S101 CEN (EUR) [Aw] ~
AA6101,196
CEN 6101, 196
466 Alloy Cross-Reference Listing
AW-61 01 B CEN (EUR) [Aw] + AW-8079 CEN (EUR) [Aw] + AW-AIMg4 CEN (EUR) [Aw] +
AA 6101B, 196 AA 8079,209 AA 5086,179
Alusuisse Anticorodal-041, 215 CEN 8079, 209 Alusuisse Peraluman-41 0/412, 224
AW-6106 CEN (EUR) [Aw] + VAW 99/01, 149 CEN 5086, 180
AA 6106, 196 AW-AI3Mn CEN (EUR) [Aw] + Hoogovens 5503, 185
Alunord 6106, 196 AA 5454, 184 NF A-G4MC, 210
CEN 6106, 196 Alusuisse Peraluman-260, 224 AW-AIMg4.5MnO.4 CEN (EUR) [Aw] +
AW-6161A CEN (EUR) [Aw] + CEN 5454, 185 AA 5182, 181
AA 6101A, 196 Hoogovens 5400, 184 CEN 5182, 182
DIN Wk. 3.2305 (AIMgSi), 145 AW-AI99.0 CEN (EUR) [Aw] + VAW 63/45, 148
AW-6262 CEN (EUR) [Aw] + AA 1200, 156 AW-AIMg4.5MnO.7 CEN (EUR) [Aw] +
AA 6262, 197 Alusuisse Pure Aluminium 99.0, 226 AA 5083,178
CEN 6262, 197 CEN 1200, 156 Alusuisse Peraluman-460/462, 225
AW-7009 CEN (EUR) [Aw] + EIN AI 99, 210 Alusuisse Peraluman-462, 225
AA 7009,199 Hoogovens 1010,151 CEN 5083, 179
lawson Mardon (lM) Star 1201, 156 Hoogovens 5510, 185
AW-7010 CEN (EUR) [Aw] + VAW 99/00, 149 Superform Metals 5083 SPF, 179
AA 7010, 199
Alusuisse Contal, 220 AW-AI99.5 CEN (EUR) [Aw] + AW-AIMn1Mg CEN (EUR) [Aw] +
CEN 7010, 199 AA 1050, 151 AA 3004, 167
Hoogovens 1000,151 CEN 3004, 167
AW-7020 CEN (EUR) [Aw] + VAW 99/52, 149 Hoogovens 3540, 171
AA 7020,200
Alusuisse Unidur 102, 229 AW-AICu4Mg1 CEN (EUR) [Aw] + Hoogovens 3541, 171
AA 2024,161 VAW 61/03, 148
CEN 7020, 200
DIN AI Zn4.5 Mg1, 214 Alusuisse Avional150, 219 AW-AISi1MgMn CEN (EUR) [Aw] +
DIN Wk. 3.4335 (AIZn4.5Mg1), 147 Alusuisse Avional152, 219 AA 6082,194
Hoogovens 7350, 206 CEN 2024, 162 Alusuisse Anticorodal110/112, 217
DIN Wk. 3.1355 (AICuMg2), 144 Alusuisse Anticorodal112/114, 217
AW-7021 CEN (EUR) [Aw] + Hoogovens 2240, 165 Alusuisse Anticorodal-1 00/1 05, 216
AA 7021,200 NF A-U4G1, 218 BOAl UK AM68, 215
CEN 7021, 201
AW-AICu4MgSi(A) CEN (EUR) [Aw] + CEN 6082, 195
AW-7022 CEN (EUR) [Aw] + AA2017A,161 DIN AI Mg Si1, 213
AA 7022,201 Alusuisse Avional1 00,218 DIN Wk. 3.2315 (AIMgSi1), 145
Alusuisse Certal, 220 Alusuisse Avional-1 02,218 Hoogovens 6010, 189
Alusuisse Perunal 205, 226 CEN 2017A, 161 NF A-SGMO.7, 218
AW-7039 CEN (EUR) [Aw] + DIN Wk. 3.1325 (AICuMg1), 144 AW-AIZn4.5Mg1 CEN (EUR) [Aw] +
AA 7039,201 NF A-U4G, 218 AA 7020,200
CEN 7039, 201 AA 2014, 159 Alusuisse Unidur 102, 229
AW-7049A CEN (EUR) [Aw] + Alusuisse Avional-660/662, 219 CEN 7020, 200
AA 7049A, 202 CEN 2014, 160 DIN AI Zn4.5 Mg1, 214
Alusuisse Perunal 249, 226 DIN Wk. 3.1255 (AICuSiMn), 144 DIN Wk. 3.4335 (AIZn4.5Mg1), 147
CEN 7049A, 202 Hoogovens 2140, 164 Hoogovens 7350, 206
AW-7050 CEN (EUR) [Aw] + AW-AIMg1SiCu CEN (EUR) [Aw] + AW-AIZn5.5MgCu CEN (EUR) [Aw] +
AA 7050,202 AA 6061, 191 AA 7075,203
CEN 7050, 202 Alusuisse Anticorodal 080,216 Alusuisse Perunal215, 226
AW-7072 CEN (EUR) [Aw] + Alusuisse Anticorodal-082, 216 CEN 7075, 204
AA 7072,203 CEN 6061, 192 DIN Wk. 3.4365 (AIZnMgCu1 ,5), 147
CEN 7072, 203 DIN Wk. 3.3211 (AIMg1SiCu), 145 Hoogovens 7750, 207
AW-7075 CEN (EUR) [Aw] +
Hoogovens 6560, 198 AW-EAL99.5 (A) CEN (EUR) [Aw] +
Reynolds R-2000, 227 AA 1350,157
AA 7075,203
Alusuisse Perunal 215, 226 AW-AIMg2 CEN (EUR) [Aw] + Alusuisse Pure Aluminium 99,5 E, 227
CEN 7075, 204 AA 5251,182 CEN 1350, 157
DIN Wk. 3.4365 (AIZnMgCu1 ,5), 147 Alusuisse Peraluman-226, 223 Hoogovens 1001,151
Hoogovens 7750, 207 CEN 5251, 183 AWSA5 [Tw] +
DIN Wk. 3.3526 (AIMg2MnO.3), 146
AW-7149 CEN (EUR) [Aw] + Ti-13V-11Cr-3AI,339
AA 7149,205 AW-AIMg2.5 CEN (EUR) [Aw] + AMS 4917,327
CEN 7149, 205 AA 5052, 177 Crucible Steel Co. B 120 VCA, 330
AW-7175 CEN (EUR) [Aw] +
Alusuisse Peraluman 253, 224 AWS A5-16 (USA) [Tcw] +
CEN 5052, 177 NF TA6V, 336
AA 7175,205
DIN Wk. 3.3523 (AIMg2.5), 146 Timetal 6-4, 321
CEN 7175, 206
AW-717B CEN (EUR) [Aw] +
Hoogovens 5520, 185 AWS A5-16 (USA) [Tw] +
VAW 63/52, 148 AMS 4905, 326
AA 7178,206
CEN 7178, 206
AW-AIMg3 CEN (EUR) [Aw] + ASTM Grade 5, 333
AA 5754,187 BS 2TA10, 317
AW-7475 CEN (EUR) [Aw] + Alusingen 234, 150 CEN Ti P63, 340
AA 7475,206 Alusuisse Peraluman-300 (301), 224 Deutsche Titan Tikrutan l T 31, 342
CEN 7475, 207 Alusuisse Peraluman-302, 224 DIN lW. 3.7164, 319
AW-8006 CEN (EUR) [Aw] + CEN 5754, 187 DIN Ti AI6 V4, 339
AA 8006,207 DIN AI Mg3 EO, 212 DIN Wk. 3.7165, 320
CEN 8006, 207 DIN Wk. 3.3535 (AIMg3), 147 DTD 5163, 328
AW-8011 A CEN (EUR) [Aw] + Hoogovens 5030, 175 NF Ti P64001, 340
AA 8011A, 207 NF A-G3, 210
CEN 8011A, 208
DIN Wk, 30915 (AIFeSi), 144
VAW 98/50, 149
Alloy Cross-Reference Listing 467
A-Z5G NF (F) [Ae] -+ AZSOA ASTM (USA) [Mw] -+
AA 712.0,244 ASTM Al80A, 302
B
CEN 71000, 254 BS2L121,297
NF A-l5G, 261 CEN MG-P-61, 311 B107 Al318-F ASTM (USA) [Mw]-+
AA 7020,200 DIN 3.5812, 297 Comeca Al31 B, 301
Alusuisse Unidur 102, 229 Magnesium Elektron AZ80, 302 Magnesium Elektron AZ31, 300
CEN 7020, 200 NF G-A7Z1, 306 B107 AZ61A-F ASTM (USA) [Mw]-+
DIN AI ln4.5 Mg1, 214 NF G-A8Z, 306 Magnesium Elecktron Al61, 301
DIN Wk. 3.4335 (Alln4.5Mg1), 147 AZS1 ASTM (USA) [Me] -+ B 120 VCA - Crucible Steel Co.
Hoogovens 7350, 206 (Prop)[Tw]-+
ASTM Al81 , 302
A-l5GU NF (F) [Aw] -+ Ti-13V-11Cr-3AI,339
AZS1A ASTM (USA) [Me] -+
AA 7075,203 AMS 4917, 327
AECMA MG-C-61 311
AA 7178,206 Crucible Steel Co. B 120 VCA, 330
ASTM AZ81A, 302
Alusuisse Perunal 215, 226 B195 Old AA (USA) [Ae]-+
BS MAG 1 , 309
CEN 7075, 204 AA 296.0, 235
BS MAG2, 309
CEN 7178, 206 AA 296.1, 235
DIN Wk. 3.5812, 297
DIN Wk. 3.4365 (AllnMgCu1.5), 147 NF G-A9, 306 AA 296.2, 236
Hoogovens 7750, 207 B214 Old AA (USA) [Ae)-+
AZS6 (Prop.) [Aw] -+
A-ZSGU NF (F) [Aw] -+ AA 512.0,242
AA 7049A, 202
AA 7001,199 AA 512.2, 242
AA 7049A, 202 AlS6 (Prop.) [Aw] -+
CEN 7049A, 202 B21S Old AA (USA) [Ae]-+
CEN 7049A, 202 AA B535.0, 277
Al10A ASTM (USA) [Mw]-+ Al91 (UK) [Me] -+
AA B535.2, 277
ASTM Al10A, 300 ASTM AZ91 D, 303
B270 - LA141 ASTM (USA) [M]-+
A-l10SSG (Prop.) [Ae]-+ Al91 ASTM (USA) [Me] -+
ASTM LA141, 307
Affimet A-l1 OS8G, 261 BS MAG?, 310
UNS M14142, 308
Magnesium Elektron AZ91, 302
AZ21X1 ASTM (USA) [Mw]-+ B295.0 Old AA (USA) [Ae] -+
ASTM Al21X1, 300 AZ91 A ASTM (USA) [Me] -+
AA 295.0,235
ASTM AZ91A, 303
Al31 ASTM (USA) [Mw] -+ AA 296.0, 235
BS MAG-x-111 , 308 AZ91 B ASTM (USA) [Me] -+
B295.1 Old AA (USA) [Ae]-+
ASTM AZ91 B, 303
AZ318 ASTM (USA) [Me]-+ AA 296.1 , 235
BS MAG-S-1110, 308 AZ91C ASTM (USA) [Me]-+
B295.2 Old AA (USA) [Ae] -+
NF G-A3Z1, 306 ASTM AZ91C, 303
AA 296.2, 236
ASTM Al31 B, 301 RIMA AZ91 C, 303
B337 3AI-2.5V ASTM (USA) [Tw] -+
DIN 3.5312, 297 AZ91 D ASTM (USA) [Me] -+
ASTM Grade 9, 333
AZ31 B-F ASTM (USA) [Mw] -+ ASTM AZ91D, 303
TimetaI3-2.5,318
Comeca AZ31 B, 301 BS MAG3, 309
DIN Wk. 3.5912, 297 B348 Grade 3 ASTM (USA) [Tw] -+
Magnesium Elektron AZ31, 300 Teledyne Alivac 50, 329
NF G-A9Z1, 306
AZ31B-O ASTM (USA) [Mw]-+ B348 Grade 4 ASTM (USA) [Tew] -+
Timminco Al91 UX, 304
Comeca AZ31 B, 301 ASTM Grade 4, 333
Timminco AZ91X, 304
Magnesium Elektron AZ31, 300 Timetal 100A, 323
AZ91 E ASTM (USA) [Me] -+
AZ31C ASTM (USA) [Me]-+ 8348 Grade 5 ASTM (USA) [Tw] -+
ASTM AZ91 E, 303
BS MAG-S-1110, 308 Teledyne Alivac 6-4, 329
Timminco AZ91 UX, 304
ASTM AZ31 C, 301
Timminco AZ91X, 304 834S/7 ASTM (USA) [Tw] -+
AZ54 (Prop.) [Aw]-+ AECMA Ti P62, 340
AZ91UX - Timminco (Prop.) [Me]-+
AA 7022,201 ASTM 17,321
ASTM AZ91D, 303
AZ61 ASTM (USA) [Mw] -+ ASTM AZ91D, 303 ASTM F7, 331
BS MAG-x-121, 308 ASTM AZ91 E, 303 Crucible Steel Co. C130AM, 330
AZ61A ASTM (USA) [Mw] -+ A AZ91X - Timminco (Prop.) [Me] -+ DTD 5053, 328
STM AZ61A, 301 ASTM AZ91 D, 303 IMI 314A, 324
AZ61 A-F ASTM (USA) [Mw] -+ ASTM AZ91 D, 303 NFTA 5M, 336
AECMA MG-P-63, 311 ASTM AZ91 E, 303 8357-2 ASTM (USA) [Ae] -+
BS MAG-E-121M, 308 AZ92A ASTM (USA) [Me] -+ Affimet Calypso 67XB1, 280
DIN 3.5612, 297 ASTM AZ92A, 304 8358.0 Old AA (USA) [Ae] -+
Magnesium Elecktron Al61 , 301 Timminco AZ92, 304 AA 358.0, 239
Ma9nesium Elecktron Al61 , 301 835S.2 Old AA (USA) [Ae] -+
AZS55 - Mag.Elek (Prop.) [Mw] -+
NF G-A6l1, 306 AA 358.2, 239
ASTM AZ80A, 302
AZ63A ASTM (USA) [Me] -+ 8367 Grade 4 ASTM (USA) [Tew] -+
AZS55 (Prop.) [Mw]-+
ASTM Al63A, 302 ASTM Grade 4, 333
ASTM AZ80F, 302
Timminco AZ63, 302 Timetal 100A, 323
AZS55 (UK) [Mw] -+
AZ66 (Prop.) [Aw]-+ 83S0.1 AA (USA) [Ae] -+
ASTM AZ80F, 302
AA 7049,202 VAW Veral 226(D), 290
AA 7149,205 AZG - Mag. Elek. (Prop.) [Me]-+
ASTM AZ63A, 302 8381 F7 ASTM (USA) [Tw] -+
CEN 7149, 205
AECMA Ti P62, 340
AZ69 (Prop.) [Aw] -+ AZM - Mag. Elek. (Prop.) [Mw] -+
ASTM 17,321
AA 7175,205 BS MAG-x-121 , 308
ASTM F7, 331
CEN 7175, 206 AECMA MG-P-63, 311 Crucible Steel Co. C130AM, 330
ASTM AZ61A, 301
DTD 5053, 328
BS MAG-E-121M, 308
IMI 314A, 324
DIN 3.5612, 297
NF TA5M, 336
NF G-A6Z1, 306
8381 Grade 4 ASTM (USA) [Tew) -+
AZM (Prop.) [Mw]-+ ASTM Grade 4, 333
Magnesium Elecktron AZ61, 301
Timetal 100A, 323
468 Alloy Cross-Reference Listing
B381 Grade F5 ASTM (USA) [Tw] ~ BS 1C (UK) [Aw] ~ BS 2L98 (UK) [Aw] ~
Teledyne Allvac 6-4, 329 AA 1200, 156 AA 2024,161
B384.0 Old AA (USA) [Ac] ~ Alusuisse Pure Aluminium 99.0, 226 Alusuisse Avional 150, 219
AA 385.0, 240 CEN 1200, 156 Alusuisse Avional 152, 219
B384.1 Old AA (USA) [Ae] ~ DIN AI 99, 210 CEN 2024, 162
AA385.1,241 Hoogovens 1010, 151 DIN Wk. 3.1355 (AICuMg2), 144
Lawson Mardon (LM) Star 1201, 156 Hoogovens 2240, 165
B390.0 AA (USA) [Ac] ~ VAW 99/00, 149 NF A-U4G1, 218
Valfond A-S17U4G, 259
BS 1E (UK) [Aw] ~ BS 2L99 (UK) [Ae] ~
B444.2 Old AA (USA) [Ae] ~ AA 1350, 157 AA 3560, 239
AA 445.2,242 AA 1350A, 157 BS 2L126 (UK) [Me] ~
B514.0 Old AA (USA) [Ae] ~ Alusuisse Pure Aluminium 99.5 E, 227 AECMA MG-C-91, 311
AA 512.0,242 CEN 1350, 157 ASTM EZ33A, 306
B514.2 Old AA (USA) [Ae] ~ DIN E-AI, 220 BS MAG6, 310
AA 512.2, 242 DIN Wk. 30257 (E-AI), 143 DIN Wk. 3.5103. 297
VAW Veral Mg3Si(H), 292 Hoogovens 1001,151 Magnesium Elektron EZ33, 304
B536-2 ASTM (USA) [Ae] ~ BS 2L55 (UK) [Aw] ~ BS 2L 127 (UK) [Me] ~
Affimet Calypso 67XB, 280 AA 5052. 177 ASTM ZK51A, 314
B750 Old AA (USA) [Ae] ~ Alusuisse Peraluman 253, 224 BS MAG4, 310
AA 8520, 245 CEN 5052, 177
BS 2L 128 (UK) [Me] ~
AA 852.1, 245 DIN Wk. 3.3523 (AIMg2.5), 146
AECMA MG-C-43, 311
Hoogovens 5520, 185
B771,O Old AA (USA) [Ae] ~ ASTM ZE41A, 314
VAW 63/52, 148
AA 7720,245 BS MAG5, 310
BS 2L56 (UK) [Aw] ~ DIN Wk. 3.5101, 297
B771.2 Old AA (USA) [Ae] ~
AA 5052. 177 Magnesium Elektron ZE41, 305
AA 7722,245
Alusuisse Peraluman 253, 224 NF G-Z4TR, 306
B1080 (Aus) [Aw] ~ CEN 5052, 177
AA 1080A, 153 BS 2L503 (UK) [Mw] ~
DIN Wk. 3.3523 (AIMg2.5), 146
CEN 1080A, 153 AECMA MG-P-63, 311
Hoogovens 5520, 185
B1200 (Aus) [Aw] ~ ASTM AZ61A, 301
VAW 63/52, 148
AA 1200, 156 BS MAG-E-121M, 308
BS 2L58 (UK) [Aw] ~ BS MAG-x-121, 308
CEN 1200, 156 AA 5056,177 DIN 3.5612. 297
B2014 (Aus) [Aw] ~ BS 2L77 (UK) [Aw] ~ Magnesium Elecktron AZ61, 301
AA 2014A, 160 AA 2014, 159 NF G-A6Z1, 306
B4043 (Aus) [Aw] ~ AA 2014A, 160 BS 2L504 (UK) [Mw] ~
AA 4043, 172 Alusuisse Avional-66o/662, 219 BS MAG-x-151 , 309
B4047 (Aus) [Aw] ~ CEN 2014, 160 BS 2L505 (UK) [Mw] ~
AA 4047, 173 Hoogovens 2140, 164 AECMA MG-P-43, 311
B6063 (Aus) [Aw] ~ BS 2L84 (UK) [Aw] ~ BS MAG-x-151, 309
AA 6063, 193 AA 6066,193 Magnesium Elektron ZW3, 315
CEN 6063, 193 BS 2L87 (UK) [Aw] ~ BS 2L508 (UK) [Mw] ~
Be38AI Lockalloy [Bw] ~ AA 2014, 159 BS MAG-x-141, 309
Brush Wellman AlbeMet AM162 Extruded AA 2014A, 160 BS 2L509 (UK) [Mw] ~
Bar, 345 Alusuisse Avional-66o/662, 219 BS MAG-x-141, 309
Brush Wellman AlbeMet AM162 Rolled CEN 2014, 160
Hoogovens 2140, 164 BS 2L512 (UK) [Mw] ~
Sheet, 345
BS MAG-x-121, 308
Beta C [Tew] ~ BS 2L91 (UK) [Ae] ~
VAW Veral Cu4Ti, 291 BS 2L513 (UK) [Mw] ~
Beta C, 330
BS MAG-x-121, 308
Beta C [Tw] ~ BS 2L92 (UK) [Ae] ~
VAW Veral Cu4Ti, 291 BS 2L514 (UK) [Mw] ~
UNS R58640, 335
BS MAG-x-151, 309
Beta III [Tw] ~ BS 2L93 (UK) [Aw] ~
AA 2014, 159 BS 2L515 (UK) [Mw] ~
Beta III, 330
AA 2014A, 160 BS MAG-x-141, 309
BS 1 (UK) [Aw] ~
Alusuisse Avional-66o/662, 219 BS 2TA1 (UK) [Tw] ~
AA 1199, 155 BS2TA1,317
CEN 1199, 155 CEN 2014, 160
Hoogovens 2140, 164 CEN Ti P99001, 341
BS 1A (UK) [Aw] ~ Timetal 35A, 322
AA 1080A, 153 BS 2L95 (UK) [Aw] ~
AA 7075,203 BS 2TA2 (UK) [Tw] ~
AA 1080A, 153 ASTM Grade 2, 332
Alusuisse Pure Aluminium 99,8, 227 Alusuisse Perunal 215, 226
CEN 7075, 204 CEN Ti P99002, 341
CEN 1080A 153 Deutsche Titan Tikrutan RT 15, 343
DIN Wk. 3.4365 (AIZnMgCu1.5), 147
DIN AI 99.8, 210
DIN Wk. 30285 (AI99.8), 143 Hoogovens 7750, 207 BS 2TA3 (UK) [Tw] ~
BS 2L97 (UK) [Aw] ~ ASTM Grade 2, 332
BS 1B (UK) [Aw] ~ CEN Ti P99002, 341
AA 1050, 151 AA 2024, 161
Alusuisse Avional 150, 219 Deutsche Titan Tikrutan RT 15, 343
AA 1050A 152
Alusingen 134, 149 Alusuisse Avional152, 219 BS 2TA4 (UK) [Tw] ~
Alusuisse Pure Aluminium 99.5, 227 CEN 2024, 162 ASTM Grade 2,332
CEN 1050A, 152 DIN Wk. 3.1355 (AICuMg2), 144 CEN Ti P99002, 341
DIN AI 99.5, 210 Hoogovens 2240, 165 Deutsche Titan Tikrutan RT 15, 343
DIN Wk. 30255 (AI99.5), 143 NF A-U4G1, 218 BS 2TA5 (UK) [Tw] ~
Hoogovens 1000, 151 ASTM Grade 2, 332
NF A-5, 210 CEN Ti P99002, 341
NF A-5L, 210 Deutsche Titan Tikrutan RT 15, 343
VAW 99/52, 149
Alloy Cross-Reference Listing 469
BS 2TA6 (UK) [Tw] -+ BS 2TA22 (UK) [Tw] -+ B5 3L58 (UK) [Aw] -+
ASTM Grade 4, 332 AECMA Ti P9001, 340 AA 5019,175
CEN Ti P99003, 341 BS 2TA21 , 317 AA 5056,177
Deutsche Titan Tikrutan RT 20, 343 Deutsche Titan Tikrutan LT 25, 341 AA 5356, 184
DIN Wk. 3.7065, 318 DIN LW 3.7124,319 CEN 5019, 175
Timetal 75A, 323 NF T-U2, 344 CEN 5356, 184
BS 2TA7 (UK) [Tew] -+ Timetal 230, 324 BS 3L63 (UK) [Aw] -+
ASTM Grade 4,333 BS 2TA23 (UK) [Tw] -+ AA 2014, 159
Timetal 100A, 323 AECMA Ti P9001, 340 AA 2014A, 160
BS 2TA8 (UK) [Tew] -+ BS 2TA21, 317 Alusuisse Avional-660/662, 219
ASTM Grade 4,333 Deutsche Titan Tikrutan LT 25, 341 CEN 2014, 160
Timetal 100A, 323 DIN LW 3.7124,319 Hoo90vens 2140, 164
BS 2TA9 (UK) [Tew] -+
NF T-U2, 344 BS 3L80 (UK) [Aw] -+
Timetal 230, 324 AA 5251, 182
ASTM Grade 4, 333
Timetal100A, 323 BS 2TA24 (UK) [Tw] -+ Alusuisse Peraluman-226, 223
AECMA Ti P9001, 340 CEN 5251, 183
BS 2TA10 (UK) [Tew] -+
BS 2TA21 , 317 DIN Wk. 3.3526 (AIMg2MnO.3), 146
AMS 4905, 326
ASTM Grade 5, 333
Deutsche Titan Tikrutan LT 25, 341 BS 3L81 (UK) [Aw] -+
DIN LW 3.7124,319 AA 5251, 182
BS 2TA10, 317
NF T-U2, 344 Alusuisse Peraluman-226, 223
CEN Ti P63, 340
Timetal 230, 324 CEN 5251, 183
Deutsche Titan Tikrutan LT 31, 342
DIN LW 3.7164, 319 BS 2TA28 (UK) [Tew] -+ DIN Wk. 3.3526 (AIMg2MnO.3), 146
DIN Ti AI6 V4, 339 AMS 4905, 326 BS 3L86 (UK) [Aw] -+
DIN Wk. 3.7165, 320 ASTM Grade 5, 333 DIN Wk. 3.1305 (AICu25Mg05), 144
DTD 5163,328 BS 2TA10, 317 BS 3L 122 (UK) [Me] -+
NF TA6V, 336 CEN Ti P63, 340
AECMA MG-C-61, 311
NF Ti P64001, 340 Deutsche Titan Tikrutan LT 31, 342 ASTM AZ81A, 302
TimetaI6-4, 321 DIN LW 3.7164, 319
BS MAG1, 309
DIN Ti AI6 V4, 339
BS 2TA11 (UK) [Tew]-+ BS MAG2, 309
DIN Wk. 3.7165, 320 DIN Wk. 3.5812, 297
AMS 4905, 326
DTD 5163, 328
ASTM Grade 5, 333 NF G-A9, 306
NF TA6V, 336
BS 2TA10, 317
NF Ti P64001, 340 BS 3L 124 (UK) [Me] -+
CEN Ti P63, 340 ASTM AZ91 C, 303
Timetal 6-4, 321
Deutsche Titan Tikrutan LT 31,342 ASTM AZ91 D, 303
DIN LW 3.7164, 319 BS 2TA52 (UK) [Tw] -+ BS MAG3, 309
DIN Ti AI6 V4, 339 AECMA Ti P9001, 340
DIN Wk. 3.5912. 297
DIN Wk. 3.7165, 320 BS 2TA21 , 317
NF G-A9Z1, 306
DTD 5163, 328 Deutsche Titan Tikrutan LT 25, 341
RIMA AZ91 C, 303
NF TA6V, 336 DIN LW 3.7124, 319
NF T-U2, 344 BS 3L 125 (UK) [Me] -+
NF Ti P64001, 340
Timetal 230, 324 ASTM AZ91C, 303
Timetal 6-4, 321
ASTM AZ91 D, 303
BS 2TA12 (UK) [Tew] -+ BS 2TA53 (UK) [Tw] -+
BS MAG3. 309
AMS 4905, 326 AECMA Ti P9001, 340 DIN Wk. 3.5912, 297
ASTM Grade 5,333 BS 2TA21 , 317
NF G-A9Z1, 306
BS 2TA10, 317 Deutsche Titan Tikrutan LT 25, 341
RIMA AZ91 C, 303
CEN Ti P63, 340 DIN LW 3.7124,319
NF T-U2, 344 BS 4L34 (UK) [Aw] -+
Deutsche Titan Tikrutan LT 31, 342 AA 1200, 156
DIN LW 3.7164, 319 Timetal 230, 324
Alusuisse Pure Aluminium 99.0, 226
DIN Ti AI6 V4, 339 BS 2TA54 (UK) [Tw] -+ CEN 1200, 156
DIN Wk. 3.7165, 320 AECMA Ti P9001, 340 DIN AI 99, 210
DTD 5163,328 BS2TA21,317
Hoogovens 1010,151
NF Ti P64001, 340 Deutsche Titan Tikrutan LT 25, 341
Lawson Mardon (LM) Star 1201, 156
TimetaI6-4, 321 DIN LW 3.7124, 319
VAW 99/00, 149
BS 2TA13 (UK) [Tew]-+ NF T-U2, 344
Timetal 230, 324 BS 5L36 (UK) [Aw] -+
AMS 4905, 326 AA 1050A, 152
ASTM Grade 5, 333 BS 2TA55 (UK) [Tw] -+ Alusingen 134,149
BS 2TA10, 317 AECMA Ti P9001 , 340 Alusuisse Pure Aluminium 99.5, 227
CEN Ti P63, 340 BS 2TA21 , 317 CEN 1050A, 152
Deutsche Titan Tikrutan LT 31, 342 Deutsche Titan Tikrutan LT 25, 341 DIN AI 99.5, 210
DIN LW 3.7164, 319 DIN LW 3.7124,319 DIN Wk. 3.0255 (AI99.5), 143
DIN Ti AI6 V4, 339 NF T-U2, 344 NF A-5, 210
DIN Wk. 3.7165, 320 Timetal 230, 324 NF A-5L, 210
DTD 5163,328 BS 2TA58 (UK) [Tw] -+ BS 5L37 (UK) [Aw] -+
NF TA6V, 336 AECMA Ti P9001, 340
NF Ti P64001, 340 AA 2017, 160
BS 2TA21 , 317 Hoogovens 2170, 164
TimetaI6-4. 321 Deutsche Titan Tikrutan LT 25, 341
BS 2TA21 (UK) [Tw] -+ DIN LW 3.7124,319 B5 5L44 (UK) [Aw] -+
AECMA Ti P9001, 340 NF T-U2, 344 AA5251,182
BS 2TA21 , 317 Timetal 230, 324 Alusuisse Peraluman-226, 223
CEN 5251, 183
Deutsche Titan Tikrutan LT 25, 341 B5 3L44 (UK) [Aw] -+ DIN Wk. 3.3526 (AIMg2MnO.3), 146
DIN LW 3.7124,319 AA 5050,176
NF T-U2, 344 Alusuisse Peraluman 150/151, 223
Timetal 230, 324 CEN 5050, 176
470 Alloy Cross-Reference Listing
C4CV (J) [Ae] -+ Calypso 67S (Prop.) [Ae] -+ CP-70 (USA) [Tew] -+
AA A356.2, 262 NF A-S7G03, 257 ASTM Grade 4, 333
VAW Pantal 7, 287 Calypso 67S2 (Prop.) [Ae] -+ Titanium Industries GR-4, 331
C-6 (USA) [Tw] -+ NF A-S7G03, 257 CP274 (discontinued) (Prop.) [Aw] -+
Teledyne Allvac 6-4, 329 Calypso 67XB (Prop.) [Ae] -+ AA 2091, 163
C7AV (J) [Ae] -+ NF A-S7G03, 257 Crucible Steel Co. B120VCA (Prop.) [Tw] -+
AA 535.2,243 Calypso 67XB1 (Prop) [Ae] -+ AMS 4917,327
VAW Veral Mg5(H), 292 NF A-S7G06, 257 Crucible Steel Co. B 120 VCA, 330
C7BV (J) [Ae] -+ Calypso 69B (Prop.) [Ae] -+
Ti-13V-11 Cr-3AI, 339
AA 520.2, 243 NF A-S 1OG, 258 Crucible Steel Co. C130AM (Prop.) [Tw] -+
VAWVeral Mg10(H), 292 Valfond Silafont 36, 288 AECMA Ti P62, 340
C-7 ELI (USA) [Tw] -+ Calypso 69N (Prop.) [Ac] -+
ASTM 17,321
Teledyne Allvac 6-4 ELI, 329 ASTM F7, 331
NF A-S10G, 258
Crucible Steel Co. C130AM, 330
C8AS (J) [Ae] -+ Valfond Silafont 36, 288
DTD 5053, 328
AA 336.1,238 Calypso 82P (Prop.) [Ac] -+ IMI 314A, 324
VAWVeral Si12CuNiMg, 294 NF A-S 12UNG, 259 NF TA 5M, 336
C8AV (J) [Ae] -+ Calypso 87P (Prop.) [Ae] -+ CS 2TA12 (UK) [Tew]-+
AA 336.2, 238 AA A3900, 263 NF TA6V, 336
VAW Veral Si12CuNiMg(H), 294 CB60 CSA (Can) [Aw] -+ CS41N Alclad CSA (Can) [Aw]-+
C-11 (USA) [Tw]-+ AA 2011, 159 AA 2014 Alclad, 160
Teledyne Allvae 6-2-4-2, 328 Alusuisse Decoltal 500, 220
CS41 N CSA (Can) [Aw] -+
C-14 (USA) [Tw]-+ CEN2011,159
AA 2014, 159
Teledyne Allvac 6-2-4-6, 329 DIN Wk. 3.1855 (AICuBiPb), 145
Alusuisse Avional-660/662, 219
C130AM - Crucible Steel Co. (Prop.) [Tw] CG30 CSA (Can) [Aw] -+ CEN 2014, 160
-+ AA 2117,164 DIN Wk. 3.1255 (AICuSiMn), 144
AECMA Ti P62, 340 DIN Wk. 3.1305 (AICu2.5Mg05), 144 Hoogovens 2140, 164
ASTM 17,321 CG42 CSA (Can) [Aw] -+ CS41P CSA (Can) [Aw] -+
ASTM F7, 331 AA 2024, 161 AA 2025, 162
Crucible Steel Co. C130AM, 330 Alusuisse Avional150, 219
DTD 5053, 328 CSN 42 4004 (Cl) [Aw] -+
Alusuisse Avional 152, 219
IMI 314A, 324 AA 1050A. 152
CEN 2024, 162
NF TA 5M, 336 Alusingen 134, 149
DIN Wk. 3.1355 (AICuMg2), 144
Alusuisse Pure Aluminium 99.5, 227
C355 Old AA (USA) [Ac] -+ Hoogovens 2240, 165
CEN 1050A, 152
AA C355 0, 277 NF A-U4G1, 218
DIN AI 99.5, 210
AA C355.2, 277 CG42 Alclad CSA (Can) [Aw] -+ NF A-5, 210
C355.0 Old AA (USA) [Ae] -+ AA 2024 Alclad, 162 NF A-5L, 210
AA 355.0,238 Class 1 (J) [Tw] -+ CSN 42 4005 (Cl) [Aw] -+
C612 Old AA (USA) [Ae] -+ ASTM Grade 1, 332 AA 1050A, 152
AA711.1, 244 JIS Class 1, 330 Alusingen 134, 149
C712.0 Old AA (USA) [Ae]-+ Class 2 (J) [Tw] -+ Alusuisse Pure Aluminium 99.5, 227
AA 711.0, 244 DIN Wk. 3.7025, 318 CEN 1050A, 152
C712.0 Old AA (USA) [Ae]-+ JIS Class 2, 330 DIN AI 99.5, 210
AA 7120,244 Class 3 (J) [Te] -+ DIN Wk. 3.0255 (AI99.5), 143
C712.1 Old AA (USA) [Ae] -+ NF T 40,336 NF A-5, 210
AA711.1,244 Class 3 (J) [Tew] -+ NF A-5L, 210
C5154 (Aus) [Aw] -+ Timetal 50A, 323 CSN 424201 (Cl) [Aw] -+
AA5154A,181 Class 3 (J) [Tw] -+ AA 2017, 160
CEN 5154A, 181 ASTM Grade 2, 332 Hoogovens 2170, 164
C5251 (Aus) [Aw] -+ DIN Wk. 3.7035. 318 CSN 42 4203 (Cl) [Aw] -+
AA 5251, 182 JIS Class 3, 331 AA 2024, 161
CEN 5251,183 CM41 CSA (Can) [Aw] -+ Alusuisse Avional 150, 219
Alusuisse Avional 152, 219
Calypso 25M (Prop.) [Ae] -+ AA 2017, 160
CEN 2024, 162
AA A206.2. 261 Hoogovens 2170, 164
DIN Wk. 3.1355 (AICuMg2), 144
Calypso 43B (Prop.) [Ac]-+ CN42 CSA (Can) [Aw] -+ Hoogovens 2240, 165
NF A-S13, 259 AA 2018, 161 NF A-U4G1, 218
Calypso 43X (Prop.) [Ae] -+ Code 12 (Prop.) [Tew]-+ CSN 42 4206 (Cl) [Aw] -+
NF A-S13, 259 ASTM Grade 12, 334 AA 2038, 163
Deutsche Titan Tikrutan LT 27, 342
Calypso 49R (Prop.) [Ae] -+ Timetal Code 12, 331 CSN 42 4207 (Cl) [Aw] -+
NF A-S9 Y4, 257 AA 2014, 159
CP1 (USA) [Tew]-+
Calypso 67B (Prop.) [Ae] -+ Alusuisse Avional-660/662, 219
NF A-S7G03, 257 ASTM Grade 4, 333 CEN 2014, 160
Titanium Industries GR-4, 331
Calypso 67B1 (Prop.) [Ae] -+ DIN Wk. 31255 (AICuSiMn), 144
NF A-S7G06, 257 CP2 (USA) [Tew] -+ Hoogovens 2140, 164
Titanium Industries GR-3, 331
Calypso 67N (Prop.) [Ae] -+ CSN 42 4218 (Cl) [Aw]-+
NF A-S7G03, 257 CP3 (USA) [Tew] -+ AA2618,165
Titanium Industries GR-2, 331
Calypso 67N1 (Prop.) [Ae] -+ CSN 42 4222 (Cl) [Aw] -+
NF A-S7G06, 257 CP3 (USA) [Tw] -+ AA 7075.203
ASTM Grade 2, 332 Alusuisse Perunal 215, 226
Calypso 67R (Prop.) [Ae] -+
NF A-S7G03, 257 CP4 (USA) [Tw] -+ CEN 7075, 204
ASTM Grade 1. 332 DIN Wk. 3.4365 (AllnMgCu1.5), 147
Calypso 67R1 (Prop.) [Ae] -+ Titanium Industries GR-1, 331 Hoogovens 7750, 207
NF A-S7G06, 257
CSN 424254 (Cl) [Aw] -+
AA 2007, 158
474 Alloy Cross-Reference Listing
CSN 42 4400 (CZ) [Aw] -+ D3V (J) [Ae] -+ DTD 118C (UK) [Mw]-+
AA 6082,194 AA 360.2, 239 ASTM MIA, 312
Alusuisse Anticorodal1101112, 217 JIS AD3. 1, 268 BS MAG-x-1 01, 308
Alusuisse Anticorodal 112/114, 217 JIS AD3.2 (ingot), 268 DTD 137 (UK) [Mw] -+
Alusuisse Anticorodal-100/105, 216 VAW Veral Si10Mg(D), 293 ASTM MIA, 312
BOAl UK AM68, 215 D5V (J) [Ae] -+ DTD 142A (UK) [Mw] -+
CEN 6082, 195 JIS AD5. 1, 268 ASTM MIA, 312
DIN AI Mg Si1, 213 JIS AD5.2 (ingot), 268
DIN Wk. 3.2315 (AIMgSi1), 145 DTD 142B (UK) [Mw] -+
D6V (J) [Ae] -+ BS MAG-x-1 01, 308
Hoogovens 6010, 189
JIS AD6. 1,268
NF A-SGMO.7, 218 DTD 150A (UK) [Aw] -+
JIS AD6.2 (ingot), 268
CSN 42 4401 (CZ) [Aw] -+ AA 2017, 160
D10V (J) [Ae]-+ Hoogovens 2170. 164
AA 6060,190
JISAD10.1,268
Alunord 6060.48, 191 DTD 259A (UK) [Mw] -+
JIS AD1 0.2 (ingot), 268
Alunord 6060.79, 191 AECMA MG-P-63, 311
Alusuisse Anticorodal 045/0501053, 216 D12V (J) [Ae] -+ ASTM AZ61A, 301
Alusuisse Extrudal-043, 221 JISAD12.1 (lME), 269 BS MAG-E-121M, 308
Alusuisse Extrudal-050, 221 JIS AD12.2 (ingot), 269 DIN 3.5612,297
BOAl UK AM62, 214 D612 Old AA (USA) [Ae]-+ NF G-A6Z1, 306
CEN 6060, 190 AA 7120,244 DTD 324A (UK) [Aw] -+
DIN AI Mg SiO.3, 212 AA 712.2,244 AA 4032, 172
DIN AI Mg SiO.5, 212 D712.0 Old AA (USA) [Ae] -+ DTD 324B (UK) [Aw] -+
DIN Wk. 3.3206 (AIMgSi05), 145 AA 712.0, 244 AA 4032, 172
NF AGS, 210 D712.2 Old AA (USA) [Ae]-+ DTD 3728 (UK) [Aw] -+
CSN 42 4412 (CZ) [Aw]-+ AA 7122.244 AA 6063, 193
AA5251,182 D8011 (Aus) [Aw] -+ CEN 6063, 193
Alusuisse Peraluman-226, 223 AA 8011,207 DIN AI Mg SiO.5, 212
CEN 5251, 183
DIN Wk. 3.3526 (AIMg2MnO.3), 146
De.Titan Tikrutan LT 24 (Prop.) [Tw] -+ DTD 619 (UK) [Mw] -+
DIN Wk. 3.7145, 319 AECMA MG-P-43, 311
CSN 42 4413 (CZ) [Aw]-+
AA 5754, 187
De. Titan Tikrutan LT 25 (Prop.) [Tw] -+ BS MAG-x-151, 309
AECMA Ti P9001, 340 Magnesium Elektron ZW3, 315
Alusingen 234, 150
BS 2TA21 , 317 DTD 622A (UK) [Mw] -+
Alusuisse Peraluman-300 (301), 224
DIN lW 3.7124,319 AECMA MG-P-43. 311
Alusuisse Peraluman-302, 224
NF T-U2, 344 BS MAG-x-151, 309
CEN 5754, 187
Timetal 230, 324 Magnesium Elektron ZW3, 315
DIN AI Mg3 EO, 212
DIN Wk. 3.3535 (AIMg3), 147 De. Titan Tikrutan l T 26 (Prop.) [Tw] -+ DTD 626B (UK) [Mw] -+
Hoogovens 5030, 175 DIN Wk. 3.7155, 319 AECMA MG-P-43. 311
NF A-G3, 210 De. Titan Tikrutan L T 27 (Prop.) [Tew] -+ BS MAG-x-151, 309
Magnesium Elektron ZW3, 315
CSN 424415 (CZ) [Aw] -+ DIN Wk. 3.7105, 318
AA 5056A, 178 De. Titan Tikrutan LT 31 (Prop) [Tw] -+ DTD 684A (UK) [Me] -+
DIN Wk. 3.3555 (AIMg5), 147 DIN Wk. 3.7165, 320 BS MAG2, 309
CSN 42 4432 (CZ) [Aw] -+ De. Titan Tikrutan l T 33 (Prop.) [Tw] -+ DTD 690A (UK) [Me] -+
AA 3003, 166 DIN Wk. 3.7175, 320 BS MAG2, 309
AA 3103, 169 De.Titan Tikrutan LT 34 (Prop.) [Tw] -+ DTD 708 (UK) [Me] -+
Alusuisse Aluman 100, 213 DIN lW 3.7184,320 AECMA MG-C-91, 311
CEN 3003, 167 DIN Wk. 3.7185, 320 ASTM EZ33A, 306
CEN 3103, 169 BS MAG6, 310
De.Titan Tikrutan l T 35 (Prop.) [Tw] -+
DIN AI Mn1, 213 DIN Wk. 3.5103, 297
DIN Wk. 3.7110, 318
DIN Wk. 3.0315 (AIMn1), 143 DTD 716B (UK) [Ae] -+
Hoogovens 3000, 166 De.Titan Tikrutan RT 12 (Prop.) [Tw]-+
BS 716B, 244
DIN Wk. 3.7025, 318
Hoogovens 3530, 170 DTD 717A (UK) [Aw]-+
lawson Mardon (lM) Star 3103, 169 De. Titan Tikrutan RT 12 Pd (Prop.) [Tw] -+ AA 2618, 165
NF 3003, 167 DIN Wk. 3.7225, 320
AA 2618A, 166
Reynolds Tread-Brite, 228 De.Titan Tikrutan RT 15 (Prop.) [Tw]-+ CEN 2618A, 166
VAW 41/20, 148 DIN Wk. 3.7035, 318 NF A-U2GN, 218
CSN 42 4441 (CZ) [Aw] -+ De.Titan Tikrutan RT 15 Pd (Prop.) [Tw]-+ DTD 722B (UK) [Ae] -+
AA 7020,200 DIN Wk. 3.7235, 321 BS 716B, 244
Alusuisse Unidur 102, 229 De. Titan Tikrutan RT 18 (Prop.) [Tw]-+ DTD 724 (UK) [Aw] -+
CEN 7020, 200 DIN Wk. 3.7055, 318 AA 2618, 165
DIN AI Zn4.5 Mg1, 214
DIN Wk. 3.4335 (AIZn4.5Mg1), 147
De. Titan Tikrutan RT 18 Pd (Prop) [Tw] -+ DTD 7278 (UK) [Ae] -+
DIN Wk. 3.7255, 321 BS 716B, 244
Hoogovens 7350, 206
CSN 42 4446 (CZ) [Aw] -+
De. Titan Tikrutan RT 20 (Prop.) [Tw] -+ DTD 729 (UK) [Mw] -+
DIN Wk. 3.7065, 318 AECMA MG-P-43, 311
AA 1100, 154
CEN 1100,154 Dilute - SECO (Prop) [Aw] -+ BS MAG-x-151, 309
AA 6060,190 Magnesium Elektron ZW3, 315
Alunord 6060.48, 191 DTD 731A (UK) [Aw]-+
D Alunord 6060.79, 191 AA2618,165
DoD: 8e38AI Lockalloy [8w] -+ DTD 731B (UK) [Aw]-+
DW (J) [Ac] -+ Brush Wellman AlbeMet AM162 Extruded AA 2618, 165
JISAD1.1,268 Bar, 345 AA 2618A, 166
JIS AD1.2 (ingot), 268 Brush Wellman AlbeMet AM162 Rolled CEN 2618A, 166
D3S (J) [Ae] -+ Sheet, 345 NF A-U2GN, 218
AA 361.1,239 DTD 88C (UK) [Mw] -+ DTD 7358 (UK) [AeJ-+
VAW Veral 233, 290 ASTM AZ80F. 302 BS 716B, 244
Alloy Cross-Reference Listing 475
DTD 737 (UK) [Mw] -+ DTD 50336 (UK) [Tw] -+ DTD 5090 (UK) [Aw] -+
BS MAG-x-l0l, 308 ASTM Grade 2, 332 AA 2024,161
DTD 742 (UK) [Me] -+ CEN Ti P99002, 341 Alusuisse Avional 150, 219
BS MAG-S-lll0, 308 Deutsche Titan Tikrutan RT 15, 343 Alusuisse Avional 152, 219
NF G-A3Z1, 306 DTD 5035 (UK) [Me] -+ CEN 2024, 162
AECMA MG-C-51, 311 DIN Wk. 3.1355 (AICuMg2), 144
DTD 742 (UK) [Mw]-+
NF G-Ag2.5TR, 306 Hoogovens 2240, 165
ASTM AZ31 B, 301
NF A-U4Gl, 218
Comeca AZ31 B, 301 DTD 5035A (UK) [Me] -+
DIN 3.5312, 297 ASTM QE22A, 312 DTD 5091 (UK) [Mw] -+
Magnesium Elektron AZ31, 300 BS MAG12, 310 BS MAG-x-131, 308
DTD 745A (UK) [Aw]-+ Magnesium Elektron MSR-B, 312 DTD 5091A (UK) [Mw]-+
AA 2618, 165 DTD 5040A (UK) [Aw] -+ Magnesium Elektron ZM21, 305
AA 2618A, 166 AA 2014,159 DTD 5093 (UK) [Tew] -+
CEN 2618A, 166 AA 2014A, 160 3620-TA7,326
NF A-U2GN, 218 Alusuisse Avional-660/662, 219 AMS 4910, 327
DTD 50036 (UK) [Tew] -+ CEN 2014, 160 AMS 4926, 328
ASTM Grade 3, 332 Hoogovens 2140, 164 ASTM Grade 6, 333
Deutsche Titan Tikrutan RT 18, 343 DTD 5041 A (UK) [Me]-+ DIN Wk. 3.7115, 318
DIN Wk. 3.7055, 318 ASTM ZK60A, 315 DTD 5083, 328
Timetal 65A, 323 ASTM ZK61A, 315 NF TA 5E, 336
DTD 5004A (UK) [Aw] -+ BS MAG-x-161, 309 DTD 5100 (UK) [Aw]-+
AA 2219, 165 DIN Wk. 3.5161,297 AA 2024 Alclad, 162
CEN 2219, 165 NF G-Z5Zr, 306 DTD 5100A (UK) [Aw]-+
DTD 5005A (UK) [Mc] -+ DTD 5043 (UK) [Tw] -+ AA 2024,161
ASTM HZ32A, 307 IMI 315, 324 Alusuisse Avional 150, 219
DTD 5045 (UK) [Me] -+ Alusuisse Avional152, 219
DTD 5005A (UK) [Me] -+
ASTM ZE63A, 314 DIN Wk. 3.1355 (AICuMg2), 144
BS MAG8, 310
Hoogovens 2240, 165
DTD 50086 (UK) [Ac] -+ DTD 5051 A (UK) [Mw] -+
NF A-U4G1, 218
AA 712.0,244 ASTM ZM21, 315
DTD 5101 (UK) [Mw] -+
DTD 5010A (UK) [Aw]-+ DTD 5053 (UK) [Tw] -+
BS MAG-x-131 , 308
AA 2014, 159 AECMA Ti P62, 340
ASTM/7,321 OTD 5101A (UK) [Mw]-+
AA 2014A, 160
ASTM F7, 331 Magnesium Elektron ZM21 , 305
Alusuisse Avional-660/662, 219
CEN 2014, 160 Crucible Steel Co. C130AM, 330 DTD 5103 (UK) [Tw]-+
Hoogovens 2140, 164 DTD 5053, 328 BS TA45, 337
IMI 314A, 324 Deutsche Titan Tikrutan LT 34, 342
DTD 5013 (UK) [Tw]-+
NF TA5M, 336 DIN LW 3.7184,320
Deutsche Titan Tikrutan RT 12,342
DTD 5055 (UK) [Me] -+ DIN Wk. 3.7185, 320
DIN Wk. 3.7025, 318
ASTM EQ21A, 305 NF TA 4DE, 336
DTD 50136 (UK) [Te] -+ Timetal 550, 324
Magnesium Elektron QE22, 304
NF T 40,336
DTD 50636 (UK) [Tw]-+ DTD 5104A (UK) [Aw]-+
Timetal 50A, 323
ASTM Grade 4, 332 AA 7014, 199
DTD 50136 (UK) [Tw]-+
Timetal 75A, 323 OTD 5110 (UK) [Aw]-+
ASTM Grade 2, 332
DTD 5073 (UK) [Tw] -+ AA 7075,203
CEN Ti P99002, 341
BS 2TA1, 317 Alusuisse Perunal215, 226
Deutsche Titan Tikrutan RT 15, 343
CEN Ti P99001, 341 CEN 7075, 204
DTD 5014A (UK) [Aw] -+ DIN Wk. 3.4365 (AIZnMgCu1.5), 147
Timetal 35A, 322
AA 2618, 165 Hoogovens 7750, 207
AA 2618A, 166 OTD 5074A (UK) [Aw] -+
AA 7075,203 DTD 5111 (UK) [Mw] -+
CEN 2618A, 166
Alusuisse Perunal 215, 226 Magnesium Elektron ZTY, 315
NF A-U2GN, 218
CEN 7075, 204 OTD 5113 (UK) [Tw]-+
DTD 5015A (UK) [Me]-+
DIN Wk. 3.4365 (AIZnMgCu1.5), 147 Timetal 679, 325
ASTM ZH62A, 314
Hoogovens 7750, 207 OTD 5120 (UK) [Aw] -+
BS MAG9, 310
OTD 5081 (UK) [Mw] -+ AA 7010, 199
DTD 5018A (UK) [Ae]-+
AECMA MG-P-43, 311 Alusuisse Contal, 220
AA 535.0, 243
BS MAG-x-151, 309 CEN 7010, 199
DTD 5023C (UK) [Tew] -+ Magnesium Elektron ZW3, 315 OTD 5121 (UK) [Aw]-+
Timetal 65A, 323
DTD 5083 (UK) [Tew] -+ AA 7075,203
DTD 5023C (UK) [Tw]-+ 3620-TA7,326 Alusuisse Perunal215, 226
ASTM Grade 3, 332 CEN 7075, 204
DTD 5083 (UK) [Tw]-+
Deutsche Titan Tikrutan RT 18, 343 DIN Wk. 3.4365 (AIZnMgCul.5), 147
AMS 4910,327
DIN Wk. 3.7055, 318 Hoogovens 7750, 207
AMS 4926, 328
DTD 5025A (UK) [Me] -+ ASTM Grade 6,333 DTD 5123 (UK) [Tw]-+
Magnesium Elektron MSR-A, 312 DIN Wk. 3.7115, 318 AECMA Ti P9001, 340
DTD 5030A (UK) [Aw] -+ DTD 5083, 328 BS 2TA21 , 317
AA 2014, 159 NF TA 5E, 336 Deutsche Titan Tikrutan LT 25, 341
AA 2014A, 160 DTD 5084A (UK) [Aw] -+ DIN LW 3.7124,319
Alusuisse Avional-660/662, 219 AA 2618, 165 NF T-U2, 344
CEN 2014, 160 AA 2618A, 166 Timetal 230, 324
Hoogovens 2140, 164 CEN 2618A, 166 OTD 5124 (UK) [Aw]-+
DTD 50336 (UK) [Tc] -+ NF A-U2GN, 218 AA 7075,203
NF T 40,336 Alusuisse Perunal215, 226
Timetal 50A, 323 CEN 7075, 204
DIN Wk. 3.4365 (AIZnMgCul.5), 147
Hoogovens 7750, 207
476 Alloy Cross-Reference Listing
DTD 5130A (UK) [Aw]-+ DTD 5223 (UK) [Tw] -+ DTD 5323 (UK) [Tew] -+
AA 7010, 199 IMI 551, 324 AMS 4905, 326
Alusuisse Contal, 220 Timetal 551, 325 ASTM Grade 5, 333
CEN 7010, 199 DTD 5233 (UK) [Tw]-+ BS 2TA10, 317
DTD 5133 (UK) [Tw] -+ AECMA Ti P9001, 340 CEN Ti P63, 340
AECMA Ti P9001, 340 BS 2TA21 , 317 Deutsche Titan Tikrutan LT 31,342
BS 2TA21 , 317 Deutsche Titan Tikrutan LT 25,341 DIN LW 3.7164, 319
Deutsche Titan Tikrutan LT 25, 341 DIN LW 3.7124,319 DIN Ti AI6 V4, 339
DIN LW 3.7124,319 NF T-U2, 344 DIN Wk. 3.7165, 320
NF T-U2, 344 Timetal 230, 324 DTD 5163,328
Timetal 230, 324 NF TA6V, 336
DTD 5243 (UK) [Tw]-+
DTD 5143 (UK) [Tw] -+ AECMA Ti P9001, 340 NF Ti P64001 , 340
AECMA Ti P62, 340 BS2TA21,317 Timetal 6-4, 321
ASTM 17,321 Deutsche Titan Tikrutan LT 25, 341 DTD 5363 (UK) [Tew] -+
ASTM F7, 331 DIN LW 3.7124,319 AMS 4905, 326
Crucible Steel Co. C130AM, 330 NF T-U2, 344 ASTM Grade 5, 333
DTD 5053, 328 Timetal 230, 324 BS 2TA10, 317
IMI 314A, 324 DTD 5253 (UK) [Tw] -+ CEN Ti P63, 340
NF TA 5M, 336 AECMA Ti P9001, 340 Deutsche Titan Tikrutan LT 31, 342
DTD 5153 (UK) [Tw] -+ BS2TA21,317 DIN LW 3.7164, 319
BS TA45, 337 DIN Ti AI6 V4, 339
Deutsche Titan Tikrutan LT 25, 341
Deutsche Titan Tikrutan LT 34, 342 DIN LW 3.7124,319 DIN Wk. 3.7165, 320
DIN LW 3.7184,320 NF T-U2, 344 DTD 5163,328
DIN Wk. 3.7185, 320 Timetal 230, 324 NF TA6V, 336
NF Ti P64001 , 340
NF TA 4DE, 336 DTD 5263 (UK) [Tw] -+ Timetal 6-4, 321
Timetal 550, 324 AECMA Ti P9001 , 340
DTD 5163 (UK) [Tcw]-+ BS 2TA21 , 317 DTD 5636 (UK) [Aw] -+
AMS 4905, 326 Deutsche Titan Tikrutan LT 25, 341 AA 7010, 199
ASTM Grade 5, 333 DIN LW 3.7124,319 Alusuisse Contal, 220
BS 2TA10, 317 NF T-U2, 344 CEN 7010, 199
CEN Ti P63, 340 Timetal 230, 324 DTD 6094A (UK) [Aw]-+
Deutsche Titan Tikrutan LT 31, 342 DTD 5283 (UK) [Tew] -+ AA 7014, 199
DIN LW 3.7164, 319 Timetal 65A, 323 Dural 2C (Prop.) [Aw] -+
DIN Ti AI6 V4, 339 AA 7017,200
OTD 5283 (UK) [Tw] -+
DIN Wk. 3.7165, 320
ASTM Grade 3, 332 Dural 2W (Prop.) [Aw] -+
DTD 5163,328 AA 7020,200
Deutsche Titan Tikrutan RT 18, 343
NF TA6V, 336 CEN 7020, 200
DIN Wk. 3.7055, 318
NF Ti P64001, 340
OTD 5293 (UK) [Te] -+ Dural F (Prop.) [Aw] -+
Timetal 6-4, 321
NF T 40,336 AA 6061, 191
DTD 5173 (UK) [Tew]-+ CEN 6061, 192
Timetal 50A, 323
AMS 4905,326
DTD 5293 (UK) [Tew] -+ Dural H (Prop.) [Aw] -+
ASTM Grade 5,333
Timetal 65A, 323 AA 6082,194
BS 2TA10, 317
CEN 6082, 195
CEN Ti P63, 340 DTD 5293 (UK) [Tw]-+
Deutsche Titan Tikrutan LT 31, 342 ASTM Grade 2, 332 Dural S (Prop.) [Aw] -+
DIN LW 3.7164, 319 ASTM Grade 3, 332 AA 2014A, 160
DIN Ti AI6 V4, 339 CEN Ti P99002, 341 Dural SF (Prop.) [Aw] -+
DIN Wk. 3.7165, 320 Deutsche Titan Tikrutan RT 15, 343 AA 2214, 164
DTD 5163,328 Deutsche Titan Tikrutan RT 18, 343 CEN 2214, 164
NF TA6V, 336 DIN Wk. 3.7055, 318 Dural SM (Prop.) [Aw] -+
NF Ti P64001, 340 DTD 5303 (UK) [Tew] -+ AA 2017A, 161
TimetaI6-4, 321 AMS 4905, 326 CEN 2017A, 161
DTD 5183 (UK) [Tc] -+ ASTM Grade 5, 333
NF T 40.336 BS 2TA10, 317
Timetal 50A, 323 CEN Ti P63, 340 E
DTD 5183 (UK) [Tw]-+ Deutsche Titan Tikrutan LT 31,342
ASTM Grade 2, 332 DIN LW 3.7164, 319 E (Prop.) [Aw] -+
DIN Ti AI6 V4, 339 DIN Wk. 30305 (AI99.9), 143
CEN Ti P99002, 341
Deutsche Titan Tikrutan RT 15, 343 DIN Wk. 3.7165, 320 EOAI Onorm (A) [Aw] -+
DTD 5163,328
DTD 5193 (UK) [Tew] -+
AA 1350,157
NF TA6V, 336 Alusuisse Pure Aluminium 99.5 E, 227
Timetal 65A, 323
NF Ti P64001 , 340 CEN 1350, 157
DTD 5193 (UK) [Tw] -+ TimetaI6-4, 321 Hoogovens 1001,151
DTD 5313 (UK) [Tew] -+
ASTM Grade 3, 332
Deutsche Titan Tikrutan RT 18, 343 E1 (Prop.) [Aw] -+
AMS 4905, 326 DIN Wk. 3.3318, 146
DIN Wk. 3.7055, 318
ASTM Grade 5, 333 E05 (Prop.) [Aw] -+
DTD 5203 (UK) [Tw] -+ BS 2TA10, 317
BS TA45, 337 DIN Wk. 3.3308 (AI99.9MgO.5), 146
CEN Ti P63, 340
Deutsche Titan Tikrutan LT 34, 342 Deutsche Titan Tikrutan LT 31, 342 E6 (UK) [Aw]-+
DIN LW 3.7184,320 DIN LW 3.7164, 319 AA 6463, 198
DIN Wk. 3.7185, 320 DIN Ti AI6 V4, 339
NF TA 4DE, 336 DIN Wk. 3.7165, 320
Timetal 550, 324 DTD 5163,328
DTD 5213 (UK) [Tw]-+ NF TA6V, 336
IMI 680, 325 NF Ti P64001, 340
TimetaI6-4, 321
Alloy Cross-Reference Listing 477
E-AI DIN (D) [Aw] -+ EN573 AW-1080A CEN (EUR) [Aw]-+ EN573 AW-2030 CEN (EUR) [Aw] -+
AA 1350,157 AA 1080A, 153 AA 2030,162
AA 1350A, 157 Alusingen 111, 149 Alusuisse Avional Pb-118, 219
Alusuisse Pure Aluminium 99.5 E, 227 Alusuisse Pure Aluminium 99.8, 227 CEN 2030, 162
CEN 1350, 157 CEN 1080A, 153 ENS73 AW-2124 CEN (EUR) [Aw] -+
DIN E-AI, 220 DIN AI 99.8, 210 AA 2124, 164
DIN Wk. 30257 (E-AI), 143 DIN Wk. 30285 (AI99.8), 143 CEN 2124, 164
Hoogovens 1001, 151 ENS73 AW-1085 CEN (EUR) [Aw] -+ ENS73 AW-2214 CEN (EUR) [Aw] -+
E-AI99.5 DIN (D) [Aw] -+ AA 1085, 153 AA 2214, 164
AA 1050, 151 Alusingen 184, 150 CEN 2214, 164
E-AI99.S ISO (EUR) [Aw] -+ Alusuisse Pure Aluminium 99.85, 227
EN573 AW-2219 CEN (EUR) [Aw] -+
AA 1350, 157 CEN 1085, 153
AA 2219, 165
AA 1350A, 157 DIN AI 99.85, 211
CEN 2219, 165
Alusuisse Pure Aluminium 99.5 E, 227 EN573 AW-1090 CEN (EUR) [Aw] -+ ENS73 AW-2618A CEN (EUR) [Aw]-+
CEN 1350, 157 AA 1090, 154 AA 2618A, 166
DIN E-AI, 220 Alusingen 119, 149 CEN 2618A, 166
DIN Wk. 30257 (E-AI), 143 Alusuisse Pure Aluminium 99.9, 227
NF A-U2GN, 218
Hoogovens 1001, 151 CEN 1090, 154
EN573 AW-3003 CEN (EUR) [Aw] -+
E-AI99.7 ISO (EUR) [Aw] -+ DIN AI 99.9, 211
AA 3003,166
AA 1370,157 DIN Wk. 3.0305 (AI99.9), 143
Alusuisse Aluman 100, 213
CEN 1370,157 EN573 AW-1100 CEN (EUR) [Aw] -+ CEN 3003, 167
E-A1995 DIN (D) [Aw] -+ AA 1100, 154 Hoogovens 3530, 170
AA 1350, 157 CEN 1100, 154 Lawson Mardon (LM) Star 3103, 169
Alusuisse Pure Aluminium 99.5 E, 227 ENS73 AW-1198 CEN (EUR) [Aw]-+ NF 3003, 167
CEN 1350,157 AA 1198, 155 Reynolds Tread-Brite, 228
Hoogovens 1001, 151 CEN 1198,155 VAW41/20, 148
E-AIMgSi DIN (D) [Aw] -+ EN573 AW-1199 CEN (EUR) [Aw] -+ EN573 AW-3004; -AIMn1Mg CEN (EUR)
AA 6463,198 AA 1199,155 [Aw]-+
DIN AI 99.85 Mg Si, 211 CEN 1199,155 AA 3004, 167
DIN AI 99.85 Mg Si04, 211 EN573 AW-1200; AW-AI99.0 CEN (EUR) CEN 3004, 167
E-AIMgSi ISO (EUR) [Aw] -+ [Aw]-+ Hoogovens 3540, 171
AA6101,196 AA 1200, 156 Hoogovens 3541, 171
CEN 6101, 196 Alusuisse Pure Aluminium 99.0, 226 VAW 61103, 148
E-AIMgSi NF (F) [Aw] -+ CEN 1200, 156 EN573 AW-3005 CEN (EUR) [Aw] -+
AA 6101, 196 DIN A199, 210 AA 3005,168
AA6101A,196 Hoogovens 1010, 151 CEN 3005, 168
CEN 6101, 196 Lawson Mardon (LM) Star 1201, 156 VAW61/15,148
VAW 99/00, 149
DIN Wk. 3.2305 (AIMgSi), 145 ENS73 AW-3103 CEN (EUR) [Aw] -+
E-AIMgSi Onorm (A) [Aw] -+ EN573 AW-1370 CEN (EUR) [Aw] -+ AA 3103, 169
AA 6101, 196 AA1370,157 CEN 3103, 169
CEN 6101,196 CEN 1370, 157 DIN AI Mn1, 213
E-AIMgSi(A) ISO (EUR) [Aw] -+ EN573 AW-2011 CEN (EUR) [Aw] -+ DIN Wk. 3.0315 (AIMnl), 143
AA 61 01A, 196 AA2011,159 Hoogovens 3000, 166
DIN Wk. 3.2305 (AIMgSi), 145 Alusuisse Decoltal 500, 220 EN573 AW-3104 CEN (EUR) [Aw] -+
CEN 2011,159
E-AIMgSiO.S DIN (D) [Aw] -+ AA 3104, 169
AA 6101,196 DIN Wk. 3.1855 (AICuBiPb), 145 CEN 3104,169
CEN 6101, 196 EN573 AW-2011A CEN (EUR) [Aw]-+ EN573 AW-310S CEN (EUR) [Aw] -+
EAIMgSiO.5 ISO (EUR) [Aw] -+ AA2011A.159 AA3105,170
AA 61 01A, 196 CEN 2011A, 159 CEN 3105, 170
DIN Wk. 3.2305 (AIMgSi), 145 EN573 AW-2014; -AICu4SiMg(A) CEN VAW61/10,148
EIE (UK) [Aw] -+ (EUR) [Aw] -+ EN573 AW4004 CEN (EUR) [Aw] -+
AA 1070A, 153 AA 2014, 159 AA 4004, 171
Alunord 1370-70,158 Alusuisse Avional-660/662, 219 CEN 4004, 171
CEN 2014, 160
CEN 1070A, 153 EN573 AW4006 CEN (EUR) [Aw] -+
DIN Wk. 3.1255 (AICuSiMn), 144
ELI C-7 (USA) [Tw] -+ Hoogovens 2140, 164
AA 4006, 171
Teledyne Allvac 6-4 ELI, 329 CEN 4006, 171
EN573 AW-2014A CEN (EUR) [Aw] -+ EN573 AW4007 CEN (EUR) [Aw] -+
EN573 AW-1050A CEN (EUR) [Aw]-+ AA 2014A, 160
AA 1050.151 AA 4007, 171
AA 1050A, 152 EN573 AW-2017A CEN (EUR) [Aw]-+ CEN 4007, 171
Alusingen 134, 149
AA 2017A, 161 ENS73 AW4043A CEN (EUR) [Aw] -+
Alusuisse Avionall00, 218 AA 4043A, 172
Alusuisse Pure Aluminium 99.5, 227
CEN 1050A, 152 Alusuisse Avional-l02, 218 CEN 4043A, 172
CEN 2017A, 161
DIN AI 995, 210
DIN Wk. 3.1325 (AICuMgl), 144 EN573 AW4045 CEN (EUR) [Aw] -+
DIN Wk. 3.0255 (AI99.5), 143 AA 4045, 172
NF A-U4G, 218
Hoogovens 1000, 151 CEN 4045, 172
EN573 AW-2024 CEN (EUR) [Aw] -+
NF A-5, 210
AA 2024, 161 EN573 AW4047A CEN (EUR) [Aw] -+
NF A-5L, 210 AA 4047A, 173
VAW 99/52, 149 Alusuisse Avional150, 219
Alusuisse Avional152, 219 CEN 4047A, 173
EN573 AW-1070A CEN (EUR) [Aw] -+ EN573 AW41 04 CEN (EUR) [Aw] -+
CEN 2024, 162
AA 1070A, 153 AA4104,173
DIN Wk. 3.1355 (AICuMg2), 144
Alunord 1370-70, 158 CEN4104,173
Hoogovens 2240, 165
CEN 1070A, 153
NF A-U4Gl, 218 EN573 AW4343 CEN (EUR) [Aw] -+
AA 4343, 173
CEN 4343, 173
478 Alloy Cross-Reference Listing
ENS73 AW-SOOS CEN (EUR) [Aw] -+ ENS73 AW-S4S4; -AI3Mn CEN(EUR)[Aw]-+ ENS73 AW-S082; -AISi1MgMn CEN (EUR)
AA 5005, 174 AA 5454, 184 [Aw] -+
Alusuisse Peraluman-100 (101),223 Alusuisse Peraluman-260. 224 AA 6082,194
CEN 5005, 174 CEN 5454, 185 Alusuisse Anticorodal1101112, 217
DIN Wk. 3.3315 (AIMg1), 146 Hoogovens 5400, 184 Alusuisse Anticorodal 112/114, 217
Hoogovens 5010, 174 ENS73 AW-S4SSA CEN (EUR) [Aw] -+ Alusuisse Anticorodal-1 0011 05, 216
ENS73 AW-S010 CEN (EUR) [Aw] -+ AA 5456A. 185 BOAl UKAM68. 215
AA 5010, 174 Alusuisse Peraluman-502. 225 CEN 6082, 195
ENS73 AW-S019 CEN (EUR) [Aw] -+ CEN 5456A, 185 DIN AI Mg Si1, 213
AA 5019, 175 ENS73 AW-SSS7 CEN (EUR) [Aw] -+ DIN Wk. 3.2315 (AIMgSi1), 145
AA 5056A, 178 AA 5657, 186 Hoogovens 6010. 189
CEN 5019, 175 Alusingen 278, 150 NF A-SGM07. 218
DIN Wk. 3.3555 (AIMg5), 147 Alusingen 289, 150 ENS73 AW-6101 CEN (EUR) [Aw] -+
ENS73 AW-S042; AIMg3.SMn CEN (EUR) AlusUisse Peraluman-860. 225 AA6101,196
[Aw] -+ Alusuisse Peraluman-863. 225 CEN 6101, 196
AA 5042. 176 CEN 5657, 186 ENS73 AW-6101B CEN (EUR) [Aw]-+
VAW 63/37, 148 DIN AI 99.85 Mg1, 211 AA 6101 B, 196
ENS73 AW-S049 CEN (EUR) [Aw] -+ ENS73 AW-S7S4; -AIMg3 CEN (EUR)[Aw]-+ Alusuisse Anticorodal-041 215
AA 5049, 176 AA 5754, 187 ENS73 AW-S10S CEN (EUR) [Aw] -+
ENS73 AW-SOSO CEN (EUR) [Aw] -+ Alusingen 234, 150 AA 6106, 196
AA 5050, 176 Alusuisse Peraluman-300 (301), 224 Alunord 6106. 196
Alusuisse Peraluman 150/151. 223 Alusuisse Peraluman-302, 224 CEN 6106, 196
CEN 5050. 176 CEN 5754, 187 ENS73 AW-S1S1A CEN (EUR) [Aw] -+
DIN AI Mg3 EQ, 212 AA 61 01A, 196
ENS73 AW-SOS1A CEN (EUR) [Aw] -+
DIN Wk. 3.3535 (AIMg3), 147 DIN Wk. 3.2305 (AIMgSi), 145
AA 5051A, 176
Hoogovens 5030, 175
CEN 5051A, 176 ENS73 AW-S2S2 CEN (EUR) [Aw] -+
NF A-G3, 210
DIN AI Mg1.8, 212 AA 6262, 197
DIN Wk. 3.3326 (AIMg1.8), 146 ENS73 AW-SOOSA CEN (EUR) [Aw] -+ CEN 6262, 197
AA 6005A, 188
ENS73 AW-SOS2; -AIMg2.S CEN (EUR) ENS73 AW-7009 CEN (EUR) [Aw] -+
Alunord 6005A, 188
[Aw]-+ AA 7009, 199
Alusuisse Anticorodal 062, 216
AA 5052, 177 ENS73 AW-7010 CEN (EUR) [Aw] -+
CEN 6005A 189
Alusuisse Peraluman 253. 224 AA 7010, 199
DIN AI Mg SiO.7, 213
CEN 5052, 177 Alusuisse Conlal. 220
NF A-SGO.5, 218
DIN Wk. 3.3523 (AIMg2.5), 146 CEN 7010. 199
Hoogovens 5520, 185 ENS73 AW-S012 CEN (EUR) [Aw] -+
AA6012,189 ENS73 AW-7019 CEN (EUR) [Aw] -+
VAW 63/52, 148 Alusuisse Unidal, 228
Alusuisse Anticorodal Pb-107, 217
ENS73 AW-SOSSA CEN (EUR) [Aw] -+ CEN 6012, 189 ENS73 AW-7020; -AIZn4.SMg1 CEN (EUR)
AA 5056A, 178 [Aw]-+
ENS73 AW-S018 CEN (EUR) [Aw] -+
DIN Wk. 3.3555 (AIMg5), 147 AA 7020,200
AA6018,190
ENS73 AW-S083; -AIMg4.SMnO.7 CEN Alusuisse Anticorodal Pb-109, 217 Alusuisse Unidur 102, 229
(EUR) [Aw] -+ CEN 7020, 200
AA 5083, 178 ENS73 AW-SOSS CEN (EUR) [Aw] -+
DIN AI Zn4.5 Mg1, 214
Alusuisse Peraluman-460/462, 225 AA 6056, 190
DIN Wk. 3.4335 (AIZn4.5Mg1). 147
CEN 6056, 190
Alusuisse Peraluman-462, 225 Hoogovens 7350, 206
CEN 5083, 179 ENS73 AW-SOSO CEN (EUR) [Aw] -+
ENS73 AW-7021 CEN (EUR) [Aw] -+
Hoogovens 5510, 185 AA 6060, 190
AA 7021,200
Superform Metals 5083 SPF, 179 Alunord 6060.48, 191
CEN 7021, 201
Alunord 6060.79, 191
ENS73 AW-S08S; -AIMg4 CEN(EUR)[Aw]-+ EN573 AW-7022 CEN (EUR) [Aw] -+
Alusuisse Anticorodal 04510501053,216
AA 5086, 179 AA 7022,201
Alusuisse Extrudal-043, 221
Alusuisse Peraluman-41 0/412, 224 Alusuisse Certal, 220
Alusuisse Extrudal-050, 221
CEN 5086, 180 Alusuisse Perunal 205, 226
BOAl UK AM62, 214
Hoogovens 5503, 185 ENS73 AW-7039 CEN (EUR) [Aw] -+
CEN 6060, 190
NF A-G4MC, 210
DIN AI Mg SiO.3, 212 AA 7039,201
ENS73 AW-S087 CEN (EUR) [Aw] -+ DIN AI Mg SiO.5, 212 CEN 7039, 201
AA 5087,180 DIN Wk. 3.3206 (AIMgSiO.5), 145 ENS73 AW-7049A CEN (EUR) [Aw] -+
CEN 5087, 180 NF AGS, 210 AA 7049A, 202
ENS73 AW-S1S4A CEN (EUR) [Aw] -+ ENS73 AW-SOS1; -AIMg1SiCu CEN (EUR) Alusuisse Perunal 249, 226
AA 5154A, 181 [Aw] -+ CEN 7049A, 202
CEN 5154A, 181 AA6061,191 ENS73 AW-70S0 CEN (EUR) [Aw] -+
ENS73 AW-S182; -AIMg4.SMnO.4 CEN Alusuisse Anticorodal 080, 216 AA 7050,202
(EUR) [Aw] -+ Alusuisse Anticorodal-082, 216 CEN 7050, 202
AA 5182, 181 CEN 6061, 192 ENS73 AW-7072 CEN (EUR) [Aw] -+
CEN 5182, 182 DIN Wk. 3.3211 (AIMg1 SiCu), 145 AA 7072,203
VAW 63/45, 148 Hoogovens 6560, 198 CEN 7072, 203
ENS73 AW-S183 CEN (EUR) [Aw] -+ Reynolds R-2000, 227
ENS73 AW-707S; -AIZnS.SMgCu CEN
AA5183,182 ENS73 AW-SOS3 CEN (EUR) [Aw] -+ (EUR) [Aw] -+
CEN 5183, 182 AA 6063,193 AA 7075,203
ENS73 AW-S2S1; -AIMg2 CEN (EUR)[Aw]-+ CEN 6063, 193 Alusuisse Perunal 215, 226
AA 5251, 182 DIN AI Mg SiO.5, 212 CEN 7075, 204
Alusuisse Peraluman-226, 223 ENS73 AW-S081 CEN (EUR) [Aw] -+ DIN Wk. 3.4365 (AIZnMgCu15), 147
CEN 5251, 183 AA 6081, 194 Hoogovens 7750, 207
DIN Wk. 3.3526 (AIMg2MnO.3), 146
ENS73 AW-7149 CEN (EUR) [Aw] -+
ENS73 AW-S3SS CEN (EUR) [Aw] -+ AA 7149,205
AA 5356, 184 CEN 7149, 205
CEN 5356, 184
Alloy Cross-Reference Listing 479
EN573 AW-7175 CEN (EUR) [Aw] -+ Erbslbh No. 5053 (Prop.) [Aw] -+ Eur. Aero P-SOS1 [Aw] -+
AA 7175,205 DIN AI 99.9 MgO.5, 211 AA 6061, 191
CEN 7175, 206 Erbslbh No. 5100 (Prop.) [Aw] -+ Alusuisse Antieorodal 080, 216
EN573 AW-717B CEN (EUR) [Aw] -+ DIN AI Mg1, 212 Alusuisse Antieorodal-082, 216
AA 7178,206 Erbslbh No, 5102 (Prop.) [Aw] -+ CEN 6061. 192
DIN Wk. 3.3211 (AIMg1 SiCu), 145
CEN 7178, 206 DIN AI 99.85 Mg1, 211
EN573 AW-7475 CEN (EUR) [Aw] -+ Erbslbh No. 5103 (Prop.) [Aw] -+ Hoogovens 6560, 198
AA 7475,206 Reynolds R-2000, 227
DIN AI 99.9 Mg1, 211
CEN 7475, 207 Eur. Aero P-S082 [Aw] -+
Erbslbh No. 5200 (Prop.) [Aw] -+ AA 6082, 194
EN573 AW-BOOS CEN (EUR) [Aw] -+ DIN AI Mg1 .8, 212
AA 8006,207 Alusuisse Anticorodal 110/112, 217
CEN 8006, 207
Erbslbh No. 5300 (Prop.) [Aw] -+ Alusuisse Anticorodal 112/114, 217
DIN AI Mg3 EQ, 212 Alusuisse Anticorodal-1 00/1 05, 216
EN573 AW-B011A CEN (EUR) [Aw]-+
AA 8011A, 207
Erbslbh No. S030 (Prop.) [Aw] -+ BOAl UKAM68, 215
DIN AI Mg SiO.3, 212 CEN 6082, 195
CEN 8011A, 208
DIN Wk. 30915 (AIFeSi), 144 Erbslbh No. S032 (Prop.) [Aw] -+ DIN AI Mg Si1, 213
DIN AI 99.85 Mg Si04, 211 DIN Wk. 3.2315 (AIMgSi1). 145
VAW 98/50, 149 Hoogovens 6010, 189
EN573 AW-B079 CEN (EUR) [Aw] -+ Erbslbh No. S040 (Prop.) [Aw] -+ NF A-SGMO.7, 218
AA 8079,209 DIN AI Mg SiO.5, 212
Eur. Aero P-7010 [Aw]-+
CEN 8079, 209 Erbslbh No. S042 (Prop.) [Aw] -+ AA 7010, 199
VAW 99/01, 149 DIN AI 99.85 Mg Si, 211
Alusuisse Contal, 220
EN573 AW-EAL99.5 tAl, 1350 CEN (EUR) Erbslbh No. S043 (Prop.) [Aw] -+ CEN 7010,199
[Aw] -+ DIN AI 99.9 Mg Si, 211 AA 7020,200
AA 1350,157 Erbslbh No. S047 (Prop.) [Aw] -+ Alusuisse Unidur 102, 229
Alusuisse Pure Aluminium 99.5 E, 227 DIN E-AI Mg SiO.5, 220 CEN 7020, 200
CEN 1350, 157 Erbslbh No. S052 (Prop.) [Aw] -+ DIN AI Zn4.5 Mg1, 214
Hoogovens1001,151 DIN AI 99.85 Mg Si, 211 DIN Wk. 34335 (AIZn4.5Mg1), 147
EN 4S500 CEN (EUR) [Ae] -+ Erbslbh No. S053 (Prop.) [Aw] -+ Hoogovens 7350, 206
CEN 46500, 253 DIN AI 99.9 Mg Si, 211 Eur. Aero P-7050 [Aw] -+
EN MG-P-S1 CEN (EUR) [Mw] -+ Erbslbh No. SOSO (Prop.) [Aw] -+ AA 7050,202
CEN MG-P-61, 311 DIN AI Mg SiO.5, 212 CEN 7050, 202
EN Ti PS3 CEN (EUR) [Tw] -+ Erbslbh No. S070 (Prop.) [Aw] -+ Eur. Aero P-7075 [Aw] -+
CEN Ti P63, 340 DIN AI Mg SiO.7, 213 AA 7075,203
EN Ti P99001 CEN (EUR) [Tw] -+ Erbslbh No. SOBO (Prop.) [Aw] -+
Alusuisse Perunal 215, 226
CEN Ti P99001, 341 CEN 7075, 204
DIN AI Mg SiO.8, 213 DIN Wk. 34365 (AIZnMgCu1 .5), 147
EN Ti P99002 CEN (EUR) [Tw] -+ Erbslbh No. S100 (Prop.) [Aw]-+ Hoogovens 7750, 207
CEN Ti P99002, 341 DIN AI Mg Si1, 213 Eur. Aero P-7150 [Aw] -+
EN Ti P99003 CEN (EUR) [Tw] -+ ES90 (Prop.) [Aw] -+ AA 7150,205
CEN Ti P99003, 341 DIN Wk. 3.3208 (AI999MgSi), 145 Eur, Aero P-7175 [Aw] -+
EQ21A ASTM (USA) [Me] -+ Eur. Aero P-2014A [Aw] -+ AA 7175,205
ASTM EQ21A, 305 AA 2014A, 160 CEN 7175, 206
EQ22A-TS ASTM (USA) [Me] -+ AA2017A,161 Eur. Aero P-7475 [Aw] -+
Magnesium Elektron EQ21, 304 Alusuisse Avional100, 218 AA 7475,206
Erbslbh No. (711) 70BO (Prop.) [Aw]-+ Alusuisse Avional-1 02, 218 CEN 7475. 207
DIN AI Zn4.5 MgO.8, 214 CEN 2017A, 161
DIN Wk. 3.1325 (AICuMg1), 144 Eur. Aero P-B090 [Aw] -+
Erbslbh No, (721) 7120 (Prop.) [Aw]-+ AA 8090,209
DIN AI Zn4.5 Mg1, 214 NF A-U4G, 218
Eur. Aero P-2024 [Aw] -+ EZ33A ASTM (USA) [Me] -+
Erbslbh No. 1001 (Prop.) [Aw] -+ AECMA MG-C-91, 311
DIN AI 99.8, 210 AA 2024, 161
Alusuisse Avional 150, 219 ASTM EZ33A. 306
Erbslbh No. 1002 (Prop.) [Aw] -+ BS MAG6, 310
Alusuisse Avional152, 219
DIN AI 99.85, 211 DIN Wk. 3.5103, 297
CEN 2024, 162
Erbslbh No. 1003 (Prop) [Aw] -+ DIN Wk. 3.1355 (AICuMg2), 144 EZ33A-T5 ASTM (USA) [Me] -+
DIN AI 99.9. 211 Hoogovens 2240, 165 Magnesium Elektron EZ33, 304
Erbslbh No, 1030 (Prop.) [Aw] -+ NF A-U4G1, 218
DIN AI 99.7, 210 Eur. Aero P-2214 [Aw] -+ F
Erbslbh No, 1050 (Prop.) [Aw] -+ AA 2214, 164
DIN AI99.5, 210 CEN 2214, 164
F3 NF (F) [Me] -+
Erbslbh No, 1057 (Prop.) [Aw] -+ Eur. Aero P-2S1BA [Aw] -+ BS MAG-S-111 0, 308
DIN E-AI, 220 AA 2618A, 166 NF G-A3Z1, 306
Erbslbh No, 1100 (Prop.) [Aw]-+ CEN 2618A, 166
F3 NF (F) [Mw] -+
DIN AI 99, 210 NF A-U2GN, 218
ASTM AZ31 B, 301
Erbslbh No. 3100 (Prop) [Aw] -+ Eur. Aero P-505SA [Aw] -+ DIN 3.5312, 297
DIN AI Mn1, 213 AA 5056A, 178 Magnesium Elektron AZ31, 300
Erbslbh No. 3110 (Prop.) [Aw] -+ DIN Wk. 3.3555 (AIMg5), 147
F3 (Prop.) [Mw] -+
DIN AI Mn Cu, 213 Eur. Aero P-50BS [Aw] -+ ASTM AZ31 B, 301
AA 5086,179
Erbslbh No. 5050 (Prop.) [Aw] -+ Comeca AZ31 B, 301
DIN AI MgO.5, 212 Alusuisse Peraluman-410/412, 224 Magnesium Elektron AZ31, 300
CEN 5086, 180
Erbslbh No. 5051 (Prop.) [Aw] -+ F3; G-A3Z1 NF (F) [Mw] -+
Hoogovens 5503, 185
DIN AI 99.8 MgO.5, 210 Comeca AZ31 B, 301
NF A-G4MC, 210
Erbslbh No. 5052 (Prop.) [Aw] -+
DIN AI 99.95 MgO.5, 211
480 Alloy Cross-Reference Listing
GOST A5 (ex USSR) [Aw] -+ Grade 4 ASTM (USA) [Tw]-+ GS11R CSA (Can) [Aw]-+
AA 1050, 151 ASTM Grade 4,332 AA 6082, 194
Hoogovens 1000, 151 CEN Ti P99003, 341 Alusuisse Anticorodal 110/112, 217
VAW 99/52, 149 Deutsche Titan Tikrutan RT 20, 343 Alusuisse Anticorodal 112/114, 217
GOST A5/ADO (ex USSR) [Aw] -+ DIN Wk. 3.7065, 318 Alusuisse Anticorodal-1 00/1 05, 216
AA 1050, 151 Teledyne Allvac 70, 329 BOAl UK AM68, 215
Hoogovens 1000, 151 Timetal 75A, 323 CEN 6082, 195
VAW 99/52, 149 Titanium IntI. Ti-4, 337 DIN AI Mg Si1, 213
GOST A6 (ex USSR) [Aw] -+ Grade 5 ASTM (USA) [Tcw] -+ DIN Wk. 3.2315 (AIMgSi1), 145
AA 1060, 152 Timetal 6-4, 321 Hoogovens 6010, 189
Titanium Industries GR-5, 331 NF A-SGMO.7, 218
lawson Mardon (lM) Star 1602, 158
GR-1 - Titanium Industries (Prop.) [Tw] -+ Grade 5 ASTM (USA) [Tw] -+ G-Th3Z2 NF (F) [Me] -+
AMS 4905, 326 ASTM HZ32A, 307
ASTM Grade 1, 332
BS MAG8, 310
GR-2 - Titanium Industries (Prop.) [Tw] -+ ASTM Grade 5, 333
CEN Ti P63, 340 G-TR3Z2 NF (F) [Me] -+
ASTM Grade 2, 332
Deutsche Titan Tikrutan l T 31, 342 AECMA MG-C-91, 311
GR-3 - Titanium Industries (Prop.) [Tw] -+ DIN Wk. 3.7165, 320 ASTM EZ33A, 306
ASTM Grade 3, 332 Teledyne Allvac 6-4,329 BS MAG6, 310
GR-4 - Titanium Industries (Prop) [Tew] -+ Titanium IntI. Ti-64, 339 DIN Wk. 3.5103, 297
ASTM Grade 4, 333 Grade 6 ASTM (USA) [Tew] -+ Magnesium Elektron EZ33 304
GR-5 - Titanium Industries (Prop.) [Tw] -+ 3620-TA7, 326 G-Z4TR NF (F) [Me] -+
ASTM Grade 5, 333 AMS 4910, 327 AECMA MG-C-43. 311
GR-7 - Titanium Industries (Prop.) [Tw]-+ AMS 4926, 328 ASTM ZE41A, 314
ASTM Grade 11, 333 ASTM Grade 6,333 BS MAG5, 310
GR-7 - Titanium Industries (Prop) [Tw] -+ DIN Wk. 3.7115, 318 DIN Wk. 3.5101, 297
ASTM Grade 7, 333 DTD 5083, 328 Magnesium Elektron ZE41 , 305
NF TA 5E, 336 NF G-Z4TR, 306
GR-12 (Prop.) [Tew]-+
ASTM Grade 12, 334 Grade 7 ASTM (USA) [Tew] -+ G-Z5Zr NF (F) [Me] -+
Titanium Industries GR-7, 332 ASTM ZK61A, 315
GR20 CSA (Can) [Aw] -+
AA 5052, 177 Grade 7 ASTM (USA) [Tw] -+ ASTM ZK60A, 315
ASTM Grade 7, 333 BS MAG-x-161, 309
Alusuisse Peraluman 253, 224
Deutsche Titan Tikrutan RT 15 Pd, 343 DIN Wk. 3.5161, 297
CEN 5052, 177
DIN Wk. 3.7235, 321 NF G-Z5Zr, 306
DIN Wk. 3.3523 (AIMg2.5), 146
Hoogovens 5520, 185 Teledyne Allvac 40+Pd, 329
VAW 63/52, 148 Titanium IntI. Ti-7, 338
H
GR40 CSA (Can) [Aw] -+ Grade 9 ASTM (USA) [Tw]-+
ASTM 3AI-2.5V, 321
AA5154,181 H9 (UK) [Aw] -+
AA 5154A, 181 ASTM Grade 9, 333
AA 6060, 190
CEN 5154A, 181 Ti-3AI-2.5V, 337
AA 6063, 193
DIN AIMg35, 212 Timetal 3-25, 318
Alunord 6060.48, 191
Grade 1 ASTM (USA) [Tw] -+ Grade 11 ASTM (USA) [Tew] -+ Alunord 6060.79, 191
DIN Wk. 3.7025, 318 Titanium Industries GR-7, 332 Alusuisse Antieorodal 045/050/053, 216
Teledyne Allvac 30, 329 ASTM Grade 11, 333 Alusuisse Extrudal-043, 221
Titanium Industries GR-1, 331 Deutsche Titan Tikrutan RT 12 Pd, 343 Alusuisse Extrudal-050, 221
Titanium IntI. Ti-1, 337 DIN Wk. 3.7225, 320 BOAl UK AM62, 214
Grade 2 ASTM (USA) [Te]-+ Grade 12 ASTM (USA) [Tew]-+ CEN 6063, 193
NF T 40,336 ASTM Grade 12, 334 DIN AI Mg SiO.3, 212
Deutsche Titan Tikrutan l T 27, 342 DIN AI Mg SiO.5, 212
Grade 2 ASTM (USA) [Tew] -+
DIN Wk. 3.7105, 318 DIN AI Mg SiO.5, 212
Timetal 50A, 323
Timetal Code 12, 331 NF AGS, 210
Titanium Industries GR-2, 331
Grade 12 ASTM (USA) [Tw]-+ H12 (UK) [Aw] -+
Grade 2 ASTM (USA) [Tw] -+ Titanium Industries GR-12, 331 AA 2031, 163
ASTM Grade 2, 332
Deutsche Titan Tikrutan RT 15, 343 Grade 21 ASTM (USA) [Tw] -+ H14 (UK) [Aw] -+
DIN Wk. 3.7035, 318 Timetal 21 S, 322 AA2017,160
Teledyne Allvac 40, 329 Grade 23 ASTM (USA) [Tw] -+ Hoogovens 2170, 164
Titanium IntI. Ti-2, 337 ASTM Grade 23, 334 H15 (UK) [Aw]-+
Grade 3 ASTM (USA) [Tcw] -+ Grade F5 ASTM (USA) [Tw] -+ AA 2014, 159
Timetal 65A, 323 Teledyne Allvac 6-4,329 AA 2014A, 160
Alusuisse Avional-660/662, 219
Titanium Industries GR-3, 331 GS10 CSA (Can) [Aw] -+
CEN 2014, 160
Grade 3 ASTM (USA) [Tw] -+ AA 6063, 193
Hoogovens 2140, 164
ASTM Grade 3, 332 CEN 6063, 193
Deutsche Titan Tikrutan RT 18, 343 DIN AI Mg SiO.5, 212 H16 (UK) [Aw]-+
DIN Wk. 3.7055, 318 AA 2618, 165
GS11N CSA (Can) [Aw]-+
Teledyne Allvac 50, 329 AA 6061, 191 H17 (UK) [Aw] -+
Teledyne Allvac 55, 329 Alusuisse Anticorodal 080, 216 AA 7020,200
Titanium IntI. Ti-3, 337 Alusuisse Anticorodal-082, 216 Alusuisse Unidur 102, 229
Grade 4 ASTM (USA) [Tcw] -+ CEN 6061, 192 CEN 7020, 200
ASTM Grade 4, 333 DIN Wk. 3.3211 (AIMg1 SiCu), 145 DIN AI Zn4.5 Mg1, 214
Timetal 100A, 323 Hoogovens 6560, 198 DIN Wk. 3.4335 (AIZn4.5Mg1), 147
Titanium Industries GR-4, 331 Reynolds R-2000, 227 Hoogovens 7350, 206
GS11 P CSA (Can) [Aw] -+
AA 6053, 190
Alloy Cross-Reference Listing 483
H19 (UK) [Aw]-+ H 2211 AC1A.1 (J) [Ae]-+ H 2212 D10V (J) [Ac]-+
AA 6005, 188 JIS AC1A (casting), 264 JISAD101,268
AA 6063,193 JISAC1A1,264 JIS AD10.2 (ingot), 268
Alunord 60B1-11, 194 H 2211 AC1A.2 (J) [Ae] -+ H 2212 D12V (J) [Ae]-+
CEN 6063, 193 JIS AC1A (casting), 264 JIS AD12.1 (lME), 269
DIN AI Mg SiO.5, 212 H 2211 AC1 B.1 (J) [Ae] -+ JIS AD12.2 (ingot), 269
H20 (UK) [Aw] -+ JIS AC1 B (casting), 265 H 2212 D1V (J) [Ae] -+
AA 6061,191 H 2211 AC1 B,2 (J) [Ae] -+ JISAD1.1,268
Alusuisse Anticorodal OBO, 216 JIS AD1.2 (ingot), 268
JIS AC1 B (casting), 265
Alusuisse Anticorodal-OB2, 216
CEN 6061, 192 H 2211 AC2A,1 (J) [Ae] -+ H 2212 D3V (J) [Ac]-+
JIS AC2A (casting), 265 JIS AD3.1, 268
DIN Wk. 3.3211 (AIMg1 SiCu), 145 JIS AD3.2 (ingot), 268
Hoogovens 6560, 198 H 2211 AC2A,2 (J) [Ae] -+
Reynolds R-2000, 227 JIS AC2A (casting), 265 H 2212 D5V (J) [Ac] -+
JIS AD5.1, 268
H30 (HE30, HS 30) (UK) [Aw] -+ H 2211 AC2B.1 (J) [Ac] -+
JIS AD5.2 (ingot), 268
AA 60B2, 194 JIS AC2B (casting), 265
H 2212 D6V (J) [Ac] -+
Alusuisse Anticorodal 110/112, 217 H 2211 AC2B.2 (J) [Ae] -+
Alusuisse Anticorodal 112/114, 217 JIS AD6.1, 268
JIS AC2B (casting), 265
JIS AD6.2 (ingot), 268
Alusuisse Anticorodal-1 00/1 05, 216 H 2211 AC3A.1 (J) [Ae] -+
BOAl UK AM6B, 215 H 5302 AD12Z.1 (J) [Ac] -+
JIS AC3A (casting), 265
CEN 60B2. 195 JIS ADC12Z (casting), 269
H 2211 AC3A.2 (J) [Ac] -+
DIN AI Mg Si1, 213 H 5302 AD14.1 (J) [Ac] -+
JIS AC3A (casting), 265
DIN Wk. 3.2315 (AIMgSi1), 145 JIS ADC14 (casting), 269
H 2211 AC4A.1 (J) [Ac]-+
Hoogovens 6010, 189 H 5302 ADC1 (J) [Ac] -+
NF A-SGMO.7, 218 JIS AC4A (casting), 265
JIS AD1.1, 268
H 2118 AD1.1 (J) [Ac]-+ H 2211 AC4A.2 (J) [Ac]-+ JIS AD1.2 (ingot), 268
JISAD1.1,268 JIS AC4A (casting), 265 JIS ADC1 (casting), 269
JIS ADC1 (casting), 269 H 2211 AC4B.1 (J) [Ac] -+ H 5302 ADC10 (J) [Ac] -+
H 2118 AD1.2 (J) [Ac] -+ JIS AC4B (casting), 266 JISAD10.1,268
JIS AD1.2 (ingot), 268 H 2211 AC4B.2 (J) [Ae]-+ JIS AD10.2 (ingot), 268
JIS ADC1 (casting), 269 JIS AC4B (casting), 266 JIS ADC1 0 (casting), 269
H 2118 AD10.1 (J) [Ac]-+ H 2211 AC4C.1 (J) [Ae]-+ H 5302 ADC10Z (J) [Ac] -+
JIS AD1 0.1, 268 JIS AC4C (casting), 266 JIS AD1 OZ.1, 268
JIS ADC1 0 (casting), 269 H 2211 AC4C.2 (J) [Ac] -+ H 5302 ADC12 (J) [Ac]-+
H 2118 AD10.2 (J) [Ae] -+ JIS AC4C (casting), 266 JIS AD12.1 (lME), 269
JIS AD10.2 (ingot), 268 H 2211 AC4CH.1 (J) [Ac] -+ JIS AD12.2 (ingot), 269
JIS ADC1 0 (casting), 269 JIS AC4CH (casting), 266 JIS ADC12 (casting), 269
H 2118 AD10Z.1 (J) [Ac]-+ H 2211 AC4CH.2 (J) [Ac] -+ H 5302 ADC12Z (J) [Ac]-+
JIS AD1 OZ.1, 268 JIS AC4CH (casting), 266 JIS AD12Z.1, 269
H 2118 AD12.1 (J) [Ae]-+ H 2211 AC4D.1 (J) [Ae] -+ H 5302 ADC14 (J) [Ac]-+
JIS ADC12 (casting), 269 JIS AC4D (casting), 266 JISAD14.1,269
H 2118 AD12.1 (LME) (J) [Ae] -+ H 2211 AC4D.2 (J) [Ae] -+ JIS AD14.2 (ingot), 269
JISAD12.1 (lME), 269 JIS AC4D (casting), 266 JIS ADC14 (casting), 270
H 2118 AD12.2 (J) [Ae] -+ H 2211 AC5A.1 (J) [Ae] -+ H 5302 ADC3 (J) [Ac] -+
JIS AD12.2 (ingot), 269 JIS AC5A (casting), 266 JIS AD3.1, 268
JIS AD3.2 (ingot), 268
JIS ADC12 (casting), 269 H 2211 AC5A.2 (J) [Ac] -+
H 2118 AD12Z (J) [Ae]-+ JIS ADC3 (casting), 269
JIS AC5A (casting), 266
JIS AD12Z.1, 269 H 5302 ADC5 (J) [Ac] -+
H 2211 AC7A.1 (J) [Ac]-+
H 2118 AD14.1 (J) [Ae]-+ JIS AD5.1, 268
JIS AC7A (casting), 267
JISAD14.1,269 JIS AD5.2 (ingot), 268
H 2211 AC7A.2 (J) [Ac]-+ JIS ADC5 (casting), 269
JIS ADC14 (casting), 270 JIS AC7A (casting), 267
H 2118 AD14.2 (J) [Ac] -+ H 5302 ADC6 (J) [Ac] -+
H 2211 AC8A.1 (J) [Ac] -+ JISAD6.1,268
JIS AD14.2 (ingot), 269 JIS ACBA (casting), 267
JIS ADC14 (casting), 270 JIS AD6.2 (ingot), 268
H 2211 AC8A.2 (J) [Ac]-+ JIS ADC6 (casting), 269
H 2118 AD3.1 (J) [Ac] -+ JIS ACBA (casting), 267
JIS AD3.1 268 HDA 66 (Prop.) [Aw]-+
JIS ADC3 (casting), 269 H 2211 AC8B,1 (J) [Ac] -+ AA 2014A, 160
JIS ACBB (casting), 267 AA 2214, 164
H 2118 AD3.2 (J) [Ae] -+
JIS AD3.2 (ingot), 268 H 2211 AC8B,2 (J) [Ac] -+ CEN 2214, 164
JIS ADC3 (casting), 269 JIS ACBB (casting), 267 HDA 75 (Prop.) [Aw] -+
H 2118 AD5,1 (J) [Ae]-+ H 2211 AC8C,1 (J) [Ac] -+ AA 7050,202
JIS ACBC (casting), 267 CEN 7050, 202
JIS AD5.1, 268
JIS ADC5 (casting), 269 H 2211 ACBC.2 (J) [Ac] -+ HDA 77 (Prop.) [Aw] -+
AA 7014, 199
H 2118 AD5.2 (J) [Ac] -+ JIS ACBC (casting), 267
JIS AD5.2 (ingot), 268 H 2211 AC9A.1 (J) [Ac] -+ HDA 81 (Prop.) [Aw]-+
JIS ADC5 (casting), 269 JIS AC9A (casting), 267 AA 7010, 199
H 2211 AC9A.2 (J) [Ae]-+ CEN 7010, 199
H 2118 AD6.1 (J) [Ae]-+
JIS AD6.1, 268 JIS AC9A (casting), 267 HDA 89 (Prop.) [Aw]-+
JIS ADC6 (casting), 269 H 2211 AC9B.1 (J) [Ac] -+ AA 7075,203
JIS AC9B (casting), 268 AA 7175,205
H 2118 AD6.2 (J) [Ae]-+ CEN 7075, 204
JIS AD6.2 (ingot), 268 H 2211 AC9B.2 (J) [Ae] -+ CEN 7175, 206
JIS ADC6 (casting), 269 JIS AC9B (casting), 268
484 Alloy Cross-Reference Listing
HE9 (UK) [Aw] -+ Hoogovens 5510 (Prop.) [Aw] -+ IMI155 (Prop.) [Tw]-+
AA 6063,193 AA 5083,178 ASTM Grade 4, 332
CEN 6063, 193 CEN 5083, 179 CEN Ti P99003, 341
DIN AI Mg SiO.5, 212 Hoogovens 5520 (Prop.) [Aw] -+ Deutsche Titan Tikrutan RT 20, 343
HG.5 ZK40A CSA (Can) [Mw] -+ AA 5052,177 DIN Wk. 3.7065, 318
ASTM ZK40A, 314 CEN 5052, 177 Timetal 75A, 323
HG9 (UK) [Aw] -+ Hoogovens 5503 (Prop.) [Aw] -+ IMI160 (Prop.) [Tew]-+
AA 6063,193 AA 5086,179 ASTM Grade 4, 333
CEN 6063, 193 CEN 5086, 180 Timeta1100A,323
DIN AI Mg SiO.5, 212 Hoogovens 6010 (Prop.) [Aw]-+ IMI160 (Prop) [Tw] -+
Hid RR58 (Prop.) [Aw] -+ AA 6082,194 Titanium IntI. Ti-4, 337
AA 2618A. 166 CEN 6082, 195 IMI 230 (Prop.) [Tw] -+
CEN 2618A, 166 Hoogovens 6560 (Prop.) [Aw] -+ AECMA Ti P9001, 340
Hiduminium 90 (Prop.) [Ae] -+ AA 6061, 191 BS 2TA21 , 317
AA 520.0,243 CEN 6061, 192 Deutsche Titan Tikrutan LT 25, 341
Hiduminium 350 Old AA (USA) [Ae] -+ Hoogovens 7350 (Prop.) [Aw] -+ DIN LW 3.7124,319
AA 203.0,233 AA 7020,200 NF T-U2, 344
AA 203.2, 233 CEN 7020, 200 Timetal 230, 324
Hiduminium 350 (Prop.) [Ae] -+ IMI 260 (Prop.) [Tw] -+
Hoogovens 7750 (Prop.) [Aw] -+
AA 2030,233 AA 7075,203 ASTM Grade 11, 333
AA 203.2, 233 CEN 7075, 204 Deutsche Titan Tikrutan RT 12 Pd, 343
DIN Wk. 3.7225, 320
HK31 A ASTM (USA) [Mew] -+ Hoogovens 7790 (Prop.) [Aw] -+
ASTM HK31A, 307 AA 7079,204 IMI 262 (Prop.) [Tw] -+
ASTM Grade 7, 333
HM21AASTM (USA) [Mw]-+ Hydro Mag. AE42 (Prop.) [Me] -+ Deutsche Titan Tikrutan RT 15 Pd, 343
ASTM HM21A, 307 Hydro Magnesium AE42, 298 DIN Wk. 3.7235, 321
HM31AASTM (USA) [Mw]-+ Hydro Mag. AM20 (Prop.) [Me] -+ Titanium IntI. Ti-7, 338
ASTM HM31A, 307 ASTM AM20, 298 IMI 314A (Prop.) [Tw] -+
Hoogovens 1000 (Prop.) [Aw] -+ Hydro Magnesium AM20, 298 AECMA Ti P62, 340
AA1050, 151 Hydro Mag. AS21 (Prop.) [Me] -+ ASTM 17,321
Hoogovens 1001 (Prop.) [Aw]-+ ASTM AS21, 299 ASTM F7, 331
AA 1350, 157 Hydro Magnesium AS21, 299 Crucible Steel Co. C 130AM, 330
CEN 1350, 157 HZ32A ASTM (USA) [Me] -+ DTD 5053, 328
Hoogovens 1010 (Prop.) [AwJ-+ ASTM HZ32A, 307 IMI 314A, 324
AA 1200, 156 BS MAG8, 310 NF TA 5M, 336
CEN 1200, 156 IMI 315 (Prop.) [Tw]-+
Hoogovens 1070 (Prop.) [Aw]-+ IMI 315, 324
AA 1070, 152 IMI 317 (Prop.) [Tew] -+
Hoogovens 2140 (Prop.) [Aw] -+ ICI 314A (Prop.) [Tw] -+
3620-TA7,326
AA 2014, 159 AMS 4910,327
AECMA Ti P62. 340 AMS 4926, 328
CEN 2014, 160 ASTM 17,321 ASTM Grade 6, 333
Hoogovens 2170 (Prop.) [Aw] -+ ASTM F7, 331 DIN Wk. 3.7115, 318
AA 2017, 160 Crucible Steel Co. C130AM, 330 DTD 5083, 328
Hoogovens 2240 (Prop.) [Aw] -+ DTD 5053, 328 NF TA 5E, 336
AA 2024, 161 IMI 314A, 324
NF TA 5M, 336 IMI318 (Prop.) [Tew] -+
CEN 2024, 162
NF TA6V, 336
Hoogovens 3000 (Prop.) [Aw] -+ IMI110 (Prop.) [Tw]-+ TimetaI6-4, 321
AA 3103, 169 ASTM Grade 1, 332
IMI318 (Prop.) [Tw]-+
CEN 3103, 169 IMI115 (Prop.) [Tw]-+ AMS 4905, 326
Hoogovens 3530 (Prop.) [Aw] -+ BS 2TA1, 317 ASTM Grade 5, 333
AA 3003, 166 CEN Ti P99001, 341 BS 2TA10, 317
CEN 3003, 167 Deutsche Titan Tikrutan RT 12, 342 CEN Ti P63, 340
NF 3003, 167 Timetal 35A, 322 Deutsche Titan Tikrutan LT 31, 342
Hoogovens 3530 Clad (Prop.) [Aw]-+ Titanium IntI. Ti-1, 337 DIN LW 3.7164, 319
AA 3003 Alclad, 167 IMI125 (Prop.) [Te]-+ DIN Ti AI6 V4, 339
Hoogovens 3540 (Prop.) [Aw] -+ NF T 40,336 DIN Wk. 3.7165, 320
AA 3004,167 IMI125 (Prop.) [Tew]-+ DTD 5163,328
CEN 3004, 167 Timetal 50A, 323 NF Ti P64001, 340
IMI125 (Prop.) [Tw]-+ Titanium IntI. Ti-64, 339
Hoogovens 3540 Clad (Prop.) [Aw]-+
AA 3004 Alelad, 168 ASTM Grade 2, 332 IMI318ELI (Prop.) [Tw]-+
ASTM Grade 23, 334
Hoogovens 3541 (Prop.) [Aw] -+ CEN Ti P99002, 341
AA 3004, 167 Deutsche Titan Tikrutan RT 15, 343 IMI 325 (Prop.) [Tw] -+
CEN 3004, 167 DIN Wk. 3.7035, 318 ASTM 3AI-2.5V. 321
Titanium IntI. Ti-2, 337 ASTM Grade 9, 333
Hoogovens 3560 Clad (Prop.) [Aw] -+
AA 3005 Alclad, 168 IMI130 (Prop.) [Tew] -+ Ti-3AI-2.5V, 337
Timetal 65A, 323 Timetal 3-2.5, 318
Hoogovens 5010 (Prop) [Aw]-+
IMI130 (Prop.) [Tw]-+ IMI 367 (Prop.) [Tw] -+
AA 5005, 174
CEN 5005, 174 ASTM Grade 3, 332 IM1367,324
Deutsche Titan Tikrutan RT 18, 343 Timetal 367, 324
Hoogovens 5030 (Prop.) [Aw] -+
DIN Wk. 3.7055,318
AA 5754,187
Titanium IntI. Ti-3, 337
CEN 5754, 187
Hoogovens 5400 (Prop.) [Aw] -+
AA 5454,184
CEN 5454, 185
Alloy Cross-Reference Listing 485
IMI 550 (Prop.) [Tw] -+ J465 SAE (USA) [Mcw] -+ JIS H 2211 AC1 A.2 (J) [Ac] -+
BS TA45, 337 ASTM HK31A, 307 JIS AC1A (casting), 264
Deutsche Titan Tikrutan LT 34, 342 J466 SAE (USA) [Mw] -+ JIS H 2211 AC1 B.1 (J) [Ac] -+
DIN LW 3.7184,320 ASTM AZ31 B, 301 JISAC1B (casting), 265
DIN Wk. 3.7185, 320
NF TA 4DE, 336
ASTM AZ61A, 301 JIS H 2211 AC1 B.2 (J) [Ac] -+
ASTM AZ80A, 302 JIS AC1 B (casting), 265
Timetal 550, 324
IMI 551 (Prop.) [Tw] -+
ASTM MIA, 312
ASTM ZK60A, 315
JIS H 2211 AC2A.1 (J) [Ac] -+
JIS AC2A (casting), 265
IM1551,324 JIS Class 1 (J) [Tw) -+
Timetal 551, 325 ASTM Grade 1, 332
JI5 H 2211 AC2A.2 (J) [Ac] -+
JIS AC2A (casting), 265
IMI 624 (Prop.) [Tw) -+ JIS Class 1, 330
AMS 4919,327 JI5 Class 2 (J) [Tw] -+
JIS H 2211 AC2B.1 (J) [Ac] -+
JIS AC2B (casting), 265
Deutsche Titan Tikrutan LT 24,341 DIN Wk. 3.7025, 318
DIN LW 3.7144,319 JIS Class 2, 330 JIS H 2211 AC2B.2 (J) [Ac] -+
JIS AC2B (casting), 265
JI5 Class 3 (J) [Tc] -+
DIN Wk. 3.7145, 319
Ti-6242, 339
NF T 40,336 JIS H 2211 AC3A.1 (J) [Ac] -+
IMI 646 (Prop.) [Tw] -+ JIS AC3A (casting), 265
IM1646,325
JI5 Class 3 (J) [Tcw] -+ JIS H 2211 AC3A.2 (J) [Ac]-+
Timetal 50A, 323
TimetaI6-2-4-6,321 JIS AC3A (casting), 265
JI5 Class 3 (J) [Tw] -+
UNS R56260, 334
ASTM Grade 2, 332 JIS H 2211 AC4A.1 (J) [Ac] -+
IMI662 (Prop.) [Tw]-+ JIS AC4A (casting), 265
DIN Wk. 3.7035, 318
AMS 4918,327
JIS Class 3, 331 JIS H 2211 AC4A.2 (J) [Ac] -+
Deutsche Titan Tikrutan LT 33, 342 JIS AC4A (casting), 265
DIN LW 3.7174,320 JIS H 2118 AD1.1 (J) [Ac]-+
JIS AD1.1, 268 JIS H 2211 AC4B.1 (J) [Ac] -+
DIN Wk. 3.7175, 320
JIS ADC1 (casting), 269 JIS AC4B (casting), 266
Timetal 6-6-2, 321
JIS H 2211 AC4B.2 (J) [Ac]-+
IMI 679 (Prop.) [Tw] -+ JIS H 2118 AD1.2 (J) [Ac]-+
JIS AD1.2 (ingot), 268 JIS AC4B (casting), 266
IM1679,325
Timetal 679, 325 JIS ADC1 (casting), 269 JIS H 2211 AC4C.1 (J) [Ac] -+
IMI 680 (Prop.) [Tw] -+ JIS H 2118 AD10.1 (J) [Ac] -+ JIS AC4C (casting), 266
IM1680,325 JIS AD1 0.1, 268 JIS H 2211 AC4C.2 (J) [Ac] -+
JIS ADC10 (casting), 269 JIS AC4C (casting), 266
IMI 685 (Prop.) [Tw] -+
Deutsche Titan Tikrutan LT 26, 341 JIS H 2118 AD10.2 (J) [Ac]-+ JIS H 2211 AC4CH.1 (J) [Ac] -+
DIN Wk. 3.7155, 319 JIS AD10.2 (ingot), 268 JIS AC4CH (casting), 266
IM1685,325 JIS ADC10 (casting), 269 JIS H 2211 AC4CH.2 (J) [Ac] -+
NF T-A6Zr5D, 337 JIS H 2118 AD10Z.1 (J) [Ac]-+ JIS AC4CH (casting), 266
Timetal 685, 325 JIS AD1 OZ.1, 268 JIS H 2211 AC4D.1 (J) [Ac] -+
IMI 700 (Prop.) [Tw] -+ JIS H 2118 AD12.1 (J) [Ac]-+ JIS AC4D (casting), 266
IM1700,325 JIS ADC12 (casting), 269 JIS H 2211 AC4D.2 (J) [Ac] -+
IMI811 (Prop.) [Tw]-+ JIS H 2118 AD12.1 (LME) (J) [Ac] -+ JIS AC4D (casting), 266
MIL R-81588, 334 JIS AD12.1 (LME), 269 JIS H 2211 AC5A.1 (J) [Ac] -+
Ti-8AI-1Mo-1V, 338 JIS H 2118 AD12.2 (J) [Ac]-+ JIS AC5A (casting), 266
Timetal 8-1-1, 322 JIS AD12.2 (ingot), 269 JIS H 2211 AC5A.2 (J) [Ac] -+
IMI 829 (Prop.) [Tw] -+ JIS ADC12 (casting), 269 JIS AC5A (casting), 266
IMIB29,326 JIS H 2118 AD12Z (J) [Ac]-+ JIS H 2211 AC7A.1 (J) [Ac]-+
Timetal 829, 326 JIS AD12Z.1, 269 JIS AC7A (casting), 267
IMI834 (Prop.) [Tw]-+ JIS H 2118 AD14.1 (J) [Ac] -+ JIS H 2211 AC7 A.2 (J) [Ac] -+
IM1834,326 JIS AD14.1, 269 JIS AC7A (casting), 267
Timetal 834, 326 JIS ADC14 (casting), 270
JIS H 2211 AC8A.1 (J) [Ac]-+
IMI Code 12 (Prop.) [Tcw] -+ JIS H 2118 AD14.2 (J) [Ac]-+ JIS ACBA (casting), 267
ASTM Grade 12, 334 JIS AD14.2 (ingot), 269
JIS H 2211 AC8A.2 (J) [Ac] -+
Deutsche Titan Tikrutan LT 27, 342 JIS ADC14 (casting), 270
JIS AC8A (casting), 267
DIN Wk. 3.7105, 318 JIS H 2118 AD3.1 (J) [Ac]-+
Timetal Code 12, 331 JIS H 2211 AC8B.1 (J) [Ac] -+
JIS AD3.1, 268
JIS ACBB (casting), 267
1519000 (IND) [Aw]-+ JIS ADC3 (casting), 269
VAW 99/01, 149 JIS H 2211 AC8B.2 (J) [Ac] -+
JIS H 2118 AD3.2 (J) [Ac]-+
1519500 (IND) [Aw] -+
JIS ACB8 (casting), 267
JIS AD3.2 (ingot), 268
AA 1050, 151 JIS ADC3 (casting), 269 JIS H 2211 AC8C.1 (J) [Ac] -+
Hoogovens 1000, 151 JIS ACBC (casting), 267
JIS H 2118 ADS.1 (J) [Ac]-+
VAW 99/52, 149 JIS AD5.1, 268 JIS H 2211 AC8C.2 (J) [Ac] -+
JIS ADC5 (casting), 269 JIS ACBC (casting), 267
JI5 H 2118 ADS.2 (J) [Ac]-+ JIS H 2211 AC9A.1 (J) [Ac] -+
J JIS AC9A (casting), 267
JIS AD5.2 (ingot), 268
JIS ADC5 (casting), 269 JIS H 2211 AC9A.2 (J) [Ac] -+
J465 SAE (USA) [Mc] -+
JIS H 2118 AD6.1 (J) [Ac]-+ JIS AC9A (casting), 267
ASTM AM1 OOA, 298
ASTM AZ81A, 302 JIS AD6.1, 268 JIS H 2211 AC9B.1 (J) [Ac]-+
ASTM AZ91A, 303 JIS ADC6 (casting), 269 JIS AC9B (casting), 268
ASTM AZ91 B, 303 JIS H 2118 AD6.2 (J) [Ac] -+ JI5 H 2211 AC9B.2 (J) [Ac]-+
ASTMAZ91C, 303 JIS AD6.2 (ingot), 268 JIS AC98 (casting), 268
ASTM AZ92A, 304 JIS ADC6 (casting), 269 JIS H 2212 D10V (J) [Ac]-+
ASTM EZ33A, 306 JIS H 2211 AC1A.1 (J) [Ac]-+ JISAD10.1,268
ASTM ZK51A, 314 JIS AC1A (casting), 264 JIS AD10.2 (ingot), 268
BS MAG4, 310 JIS AC1A.1, 264
RIMA AZ91C, 303
486 Alloy Cross-Reference Listing
JIS H 2212 D12V (J) [Ac]-+ L81 (UK) [Aw] -+ L 156-L159 (UK) [Aw] -+
JIS AD12.1 (LME), 269 AA 5052, 177 AA 2014, 159
JIS AD12.2 (ingot), 269 Alusuisse Peraluman 253, 224 AA 2014A, 160
JIS H 2212 D1V (J) [Ac] -+ CEN 5052, 177 Alusuisse Avional-660/662, 219
JISAD1.1,268 DIN Wk. 3.3523 (AIMg2.5), 146 CEN 2014, 160
JIS AD1.2 (ingot), 268 Hoogovens 5520, 185 Hoogovens 2140, 164
JIS H 2212 D3V (J) [Ac] -+ VAW 63/52, 148 L 160 (UK) [Aw] -+
JIS AD3.1, 268 L86 (UK) [Aw] -+ AA 7075,203
JIS AD3.2 (ingot), 268 AA2117,164 Alusuisse Perunal 215. 226
JIS H 2212 D5V (J) [Ac] -+ L87 (UK) [Aw] -+ CEN 7075, 204
JIS AD5.1 , 268 AA 2017, 160 DIN Wk. 3.4365 (AIZnMgCu1.5), 147
JIS AD5.2 (ingot), 268 Hoogovens2170, 164 Hoogovens 7750. 207
JIS H 2212 D6V (J) [Ac] -+ L93 (UK) [Aw] -+ L 161 (UK) [Aw] -+
JIS AD6.1, 268 AA2017A,161 AA 7075.203
JIS AD6.2 (ingot), 268 Alusuisse Avional100, 218 Alusuisse Perunal 215. 226
Alusuisse Avional-1 02, 218 CEN 7075, 204
JIS H 5302 AD12Z.1 (J) [Ac]-+
CEN 2017A, 161 DIN Wk. 3.4365 (AIZnMgCu15) 147
JIS ADC12Z (casting), 269
DIN Wk. 3.1325 (AICuMg1), 144 Hoogovens 7750. 207
JIS H 5302 AD14.1 (J) [Ac]-+ NF A-U4G, 218 L 162 (UK) [Aw] -+
JIS ADC14 (casting), 269
L94 (UK) [Aw] -+ AA 7075,203
JIS H 5302 ADC1 (J) [Ac] -+ AA2017A,161 Alusuisse Perunal 215. 226
JISAD1.1,268 AlusuisseAvional 100, 218 CEN 7075, 204
JIS AD1.2 (ingot), 268 DIN Wk. 3.4365 (AIZnMgCu1.5), 147
Alusuisse Avional-1 02, 218
JIS ADC1 (casting), 269 Hoogovens 7750, 207
CEN 2017A, 161
JIS H 5302 ADC10 (J) [Ac] -+ DINWk. 3.1325 (AICuMg1), 144 L163-L168 (UK) [Aw]-+
JIS AD1 0.1, 268 NF A-U4G, 218 AA 2014, 159
JIS AD10.2 (ingot), 268 L96 (UK) [Aw] -+ AA 2014A, 160
JIS ADC10 (casting), 269 Alusuisse Avional-660/662. 219
AA 7075,203
JIS H 5302 ADC10Z (J) [Ac]-+ Alusuisse Perunal 215, 226 CEN 2014, 160
JIS AD1 OZ.1, 268 CEN 7075. 204 Hoogovens 2140. 164
JIS H 5302 ADC12 (J) [Ac] -+ DIN Wk. 3.4365 (AIZnMgCu1.5), 147 L169 (UK) [Ac]-+
JIS AD12.1 (LME), 269 Hoogovens 7750, 207 AA 357.0, 239
JIS AD12.2 (ingot), 269 L 102 (UK) [Aw]-+ L170 (UK) [Aw] -+
JISADC12 (casting), 269 AA 2014, 159 AA 7075,203
JIS H 5302 ADC12Z (J) [Ac]-+ AA 2014A, 160 Alusuisse Perunal 215, 226
JISAD12Z.1,269 Alusuisse Avional-660/662, 219 CEN 7075, 204
JIS H 5302 ADC14 (J) [Ac] -+ CEN 2014, 160 DIN Wk. 3.4365 (AIZnMgCu1.5), 147
JIS AD14.1, 269 Hoogovens 2140, 164 Hoogovens 7750, 207
JIS AD14.2 (ingot), 269 L103 (UK) [Aw]-+ L 173 (UK) [Ac] -+
JIS ADC14 (casting), 270 AA 2014, 159 AA 356.0, 239
JIS H 5302 ADC3 (J) [Ac] -+ AA 2014A, 160 L 174 (UK) [Ac] -+
JIS AD3.1, 268 Alusuisse Avional-660/662, 219 AA 356.0,239
JIS AD3.2 (ingot), 268 CEN 2014, 160
L214 Old AA (USA) [Ac]-+
JIS ADC3 (casting), 269 Hoogovens 2140, 164
AA 515.0,243
JIS H 5302 ADC5 (J) [Ac] -+ L105 (UK) [Aw] -+ AA 515.2, 243
AA 2014, 159
JIS AD5.1, 268 L504 (UK) [Mw] -+
JIS AD5.2 (ingot), 268 AA 2014A, 160
AECMA MG-P-43. 311
JIS ADC5 (casting), 269 Alusuisse Avional-660/662, 219
Magnesium Elektron ZW3, 315
CEN 2014, 160
JIS H 5302 ADC6 (J) [Ac] -+ L512 (UK) [Mw] -+
Hoogovens 2140, 164
JIS AD6.1, 268 AECMA MG-P-63, 311
JIS AD6.2 (ingot), 268 L117 (UK) [Aw]-+ ASTM AZ61A, 301
JIS ADC6 (casting), 269 AA 6061, 191
BS MAG-E-121M, 308
Alusuisse Anticorodal OBO, 216 DIN 3.5612, 297
Alusuisse Anticorodal-OB2, 216
Magnesium Elecktron AZ61 , 301
K CEN 6061, 192
NF G-A6Z1, 306
DIN Wk. 3.3211 (AIMg1 SiCu), 145
L513 (UK) [Mw] -+
K1A ASTM (USA) [Mc] -+ Hoogovens 6560, 198
AECMA MG-P-63, 311
ASTM K1A, 307 Reynolds R-2000, 227
ASTM AZ61A, 301
Kaiser Kalite 2090 (Prop.) [Aw] -+ L118 (UK) [Aw]-+ BS MAG-E-121M, 308
AA 2090, 163 AA 6061, 191
DIN 3.5612, 297
Alusuisse Anticorodal OBO, 216 Magnesium Elecktron AZ61 , 301
Alusuisse Anticorodal-OB2, 216 NF G-A6Z1, 306
L CEN 6061, 192
L514 (UK) [Mw] -+
DIN Wk. 3.3211 (AIMg1 SiCu), 145
AECMA MG-P-43, 311
L80 (UK) [Aw] -+ Hoogovens 6560, 198
Magnesium Elektron ZW3, 315
AA 5052, 177 Reynolds R-2000, 227
Alusuisse Peraluman 253, 224 L 119 (UK) [Ac] -+ L514.0 Old AA (USA) [Ac]-+
BS L119, 284 AA 515.0,243
CEN 5052, 177
AA 515.2, 243
DIN Wk. 3.3523 (AIMg2.5), 146 L 154 (UK) [Ac] -+
Hoogovens 5520, 185 AA 295.0, 235 L-2640 UNE (E) [Ac] -+
VAW 63/52, 148 BS L 154,284 CEN 46100,253
L-3001 UNE (E) [Aw] -+ L-3322 UNE (E) [Aw] -+ L-3611 UNE (E) [Aw] -+
AA 1200, 156 AA 5086, 179 AA 8011, 207
Alusuisse Pure Aluminium 99.0, 226 Alusuisse Peraluman-41 0/412, 224 Lawson Mardon (LM) Star 1084, 153
CEN 1200, 156 CEN 5086, 180 L-3710 UNE (E) [Aw]-+
DIN AI 99, 210 Hoogovens 5503, 185 AA 7075,203
Hoogovens 1010, 151 NF A-G4MC, 210 Alusuisse Perunal 215, 226
Lawson Mardon (LM) Star 1201, 156 L-3350 UNE (E) [Aw] -+ CEN 7075, 204
VAW 99/00, 149 AA 5005, 174 DIN Wk 3.4365 (AIZnMgCu1.5), 147
VAW 99/01, 149 Alusuisse Peraluman-100 (101), 223 Hoogovens 7750, 207
L-3051 UNE (E) [Aw] -+ CEN 5005, 174 L-3741 UNE (E) [Aw] -+
AA 1050,151 DIN Wk. 3.3315 (AIMg1), 146 AA 7020,200
AA 1050A, 152 Hoogovens 5010, 174 Alusuisse Unidur 102,229
Alusingen 134, 149 L-3361 UNE (E) [Aw] -+ CEN 7020, 200
Alusuisse Pure Aluminium 995, 227 AA5251,182 DIN AI Zn4.5 Mg1, 214
CEN 1050A, 152 Alusuisse Peraluman-226, 223 DIN Wk. 3.4335 (AIZn4.5Mg1), 147
DIN AI 99.5, 210 CEN 5251, 183 Hoogovens 7350, 206
DIN Wk. 3.0255 (AI99.5), 143 DIN Wk. 3.3526 (AIMg2MnO.3), 146 L-3751 UNE (E) [Aw]-+
Hoogovens 1000, 151
L-3390 UNE (E) [Aw] -+ AA 7022,201
NF A-5, 210
AA 5754, 187 Alusuisse Certal, 220
NF A-5L, 210 Alusingen 234, 150 Alusuisse Perunal 205, 226
VAW 99/52, 149
Alusuisse Peraluman-300 (301), 224 L-3811 UNE (E) [Aw]-+
L3052 UNE (E) [Aw] -+ Alusuisse Peraluman-302, 224 AA 3103, 169
AA 1350A, 157 CEN 5754, 187 CEN 3103, 169
DIN E-AI, 220 DIN AI Mg3 EO, 212 DINAIMn1,213
DIN Wk. 3.0257 (E-AI), 143 DIN Wk. 3.3535 (AIMg3), 147 DIN Wk. 3.0315 (AIMn1), 143
L-3081 UNE (E) [Aw] -+ Hoogovens 5030, 175 Hoogovens 3000, 166
AA 1080A, 153
L-3831 UNE (E) [Aw] -+
NF A-G3, 210
Alusingen 111, 149 L-3391 UNE (E) [Aw] -+ AA 3105, 170
Alusuisse Pure Aluminium 99.8, 227 AA 5454, 184 CEN 3105, 170
CEN 1080A, 153 Alusuisse Peraluman-260, 224 VAW61110, 148
DIN AI 998, 210 CEN 5454, 185
DIN Wk. 3.0285 (AI99.8), 143 LA141 ASTM (USA) [M] -+
Hoogovens 5400, 184 ASTM LA141, 307
L-3130 UNE (E) [Aw] -+ L-3392 UNE (E) [Aw] -+ UNS M14142, 308
AA 2014, 159
LMO (UK) [Ac] -+
AA5154A,181
AA 2014A, 160 CEN 5154A. 181
Alusuisse Avional-660/662, 219 AA 150.1, 233
L-3420 UNE (E) [Aw] -+ AA 170.1, 233
CEN 2014, 160
AA 6061, 191 VAW Veral 99.5, 289
DIN Wk. 3.1255 (AICuSiMn), 144
Alusuisse Anticorodal 080, 216 VAW Veral 99.7, 289
Hoogovens2140, 164
Alusuisse Anticorodal-082, 216
L-3140 UNE (E) [Aw] -+ LM2 (UK) [Ac] -+
CEN 6061, 192
AA 2024, 161 AA A413.1, 263
DIN Wk. 3.3211 (AIMg1 SiCu), 145
Alusuisse Avional150, 219 NF A-S10G, 258
Hoogovens 6560, 198
Alusuisse Avional 152, 219 VAW Veral231 (0),290
Reynolds R-2000, 227
CEN 2024, 162 VAW Veral 231A, 290
L-3431 UNE (E) [Aw] -+ LM4 (UK) [Ac] -+
DIN Wk. 3.1355 (AICuMg2), 144
AA 61 01A, 196
Hoogovens2240, 165 AA 319.0, 237
DIN Wk. 3.2305 (AIMgSi), 145
NF A-U4G1, 218 CEN 45200, 252
L-315 UNE (E) [Aw]-+
L-3441 UNE (E) [Aw] -+ LM5 (UK) [Ac]-+
AA 6063, 193
AA 2218, 164 AA 204.2, 234
CEN 6063, 193
L-3160 UNE (E) [Aw] -+ DIN AI Mg Si05, 212
AA511.1,242
AA2031,163 AA 5140,243
L-3442 UNE (E) [Aw] -+ AA 514.2,243
L-3171 UNE (E) [Aw]-+ AA 6060, 190 AA 535.2, 243
AA 2618A, 166 Alunord 6060.48, 191 VAW Vera1241, 291
CEN 2618A, 166 Alunord 6060.79, 191 VAW Veral Cu4TiMg, 291
L-3180 UNE (E) [Aw] -+ Alusuisse Anticorodal 045/050/053, 216 VAW Veral Mg3(H), 291
AA2117,164 Alusuisse Extrudal-043, 221 VAW Veral Mg3, 291
DIN Wk 3.1305 (AICu2 5MgO.5), 144 Alusuisse Extrudal-050, 221 VAW Veral Mg5(H), 292
L-3192 UNE (E) [Aw] -+ BOAL UK AM62, 214
LM6 (UK) [Ac] -+
AA2011,159 CEN 6060, 190
AAA413.2,263
Alusuisse Decoltal 500, 220 DIN AI Mg SiO.3, 212
NF A-S12, 258
CEN 2011, 159 DIN AI Mg SiO.5, 212
VAW Silumin, 288
DIN Wk. 3.1855 (AICuBiPb), 145 DIN Wk. 3.3206 (AIMgSiO.5), 145
VAW Veral Si12A, 293
L-3320 UNE (E) [Aw] -+ NF AGS, 210
LM8 (UK) [Ac] -+
AA 5019, 175 L-3453 UNE (E) [Aw] -+ VAW Veral Si5MgA, 293
AA 6082,194
LM9 (UK) [Ac] -+
AA 5056A, 178
CEN 5019, 175 Alusuisse Anticorodal 110/112, 217
Alusuisse Anticorodal112/114, 217 AA 359.2, 239
DIN Wk. 3.3555 (AIMg5), 147
AA 369.1, 240
L-3321 UNE (E) [Aw] -+ Alusuisse Anticorodal-1 00/1 05, 216
VAW Silumin-Beta, 288
BOAL UKAM68, 215
AA 5083, 178 VAW Silumin-Kappa, 289
Alusuisse Peraluman-460/462, 225 CEN 6082, 195
DIN AI Mg Si1, 213 VAW Veral Si1 OMgA, 293
Alusuisse Peraluman-462, 225
DIN Wk. 3.2315 (AIMgSi1), 145
CEN 5083, 179
Hoogovens 5510, 185 Hoogovens 6010, 189
NF A-SGMO.7, 218
Superform Metals 5083 SPF, 179
L-3541 UNE (E) [Aw] -+
AA 4032, 172
488 Alloy Cross-Reference Listing
LM10 (UK) [Ae] ~ LT 25 - Tikrutan (Prop.) [Tw] ~ LW 3.7034 DIN (D) [Tw] ~
AA518.1,243 AECMA Ti P9001 , 340 ASTM Grade 2, 332
AA 520.0,243 BS 2TA21 , 317 CEN Ti P99002, 341
AA 520.2, 243 DIN LW 3.7124,319 LW 3.7064 DIN (D) [Tew] ~
VAW Veral Mg10(H), 292 NF T-U2, 344 ASTM Grade 4, 333
VAW Veral Mg9, 292 Timetal 230, 324 Timetal 100A, 323
LM11 (UK) [Ae] ~ L T 26 - Tikrutan (Prop.) [Tw] ~ LW 3.7064 DIN (D) [Tw] ~
AA 295.0, 235 DIN Wk. 3.7155, 319 ASTM Grade 4, 332
VAW Veral Cu4Ti, 291 LT 27 - Tikrutan (Prop.) [Tew] ~ Timetal 75A, 323
LM13 (UK) [Ae] ~ DIN Wk. 3.7105, 318 LW 3.7154 DIN (D) [Tw] ~
AA 336.1,238 L T 31 - Tikrutan (Prop.) [Tw] ~ IM1685,325
AA 336.2, 238 DIN Wk. 3.7165, 320 NF T-A6Zr5D, 337
VAW Veral Si12CuNiMg(H), 294 Timetal 685, 325
LT 33 - Tikrutan (Prop.) [Tw] ~
VAW Veral Si12CuNiMg, 294
DIN Wk. 3.7175, 320 LW 3.7174 DIN (D) [Tw] ~
LM16 (UK) [Ae] ~ AMS 4918, 327
LT 34 (Prop.) [Tw] ~
AA 3550,238 DIN LW 3.7174, 320
DIN LW 3.7184,320
CEN 45300, 252 Timetal 6-6-2, 321
DIN Wk. 3.7185, 320
UNI 3600, 247
LT 35 - Tikrutan (Prop.) [Tw] ~ LW 3,7184 DIN (D) [Tw] ~
LM20 (UK) [Ae] ~ BS TA45, 337
DIN Wk. 3.7110, 318
AAA413.1,263 NF TA 4DE, 336
VAW Veral Si12A(D), 293 LW 3.1924 DIN (D) [Aw] ~
Timetal 550, 324
AA 2618A, 166
LM21 (UK) [Ae] ~ LW 3,7194 DIN (D) [Tw] ~
CEN 2618A, 166
AAA319.1,262 ASTM 3AI-2.5V, 321
NF A-U2GN, 218
VAW Veral 225, 290 ASTM Grade 9, 333
LW 3.4144 DIN (D) [Aw] ~
LM22 (UK) [Ae] ~ Timetal 3-2.5, 318
AA 7050,202
AA319.0,237
AA 7150,205
CEN 45400, 252
CEN 7050, 202 M
LM24 (UK) [Ae] ~
LW 3.4334 DIN (D) [Aw] ~
AA 333.0, 237
AA 7175,205 M1 CSA (Can) [Aw] ~
AA 333.1, 238
CEN 7175, 206 AA 3103,169
AA 380.0,240
AA B380.1, 276 LW 3.4354 DIN (D) [Aw] ~ CEN 3103, 169
NF A-S9U3, 258 AA 7009,199 DIN AI Mn1, 213
VAW Veral 226(D), 290 LW 3.4384 DIN (D) [Aw] ~ DIN Wk. 30315 (AIMn1), 143
VAW Veral 226A, 290 AA 7475,206 Hoogovens 3000, 166
LM25 (UK) [Ae] ~ CEN 7475, 207 M1 NF (F) [Mw] ~
AA 356.0, 239 LW 3.4394 DIN (D) [Aw] ~ AECMA MG-P-63, 311
AA A356.2, 262 AA 7010, 199 ASTM AZ61A, 301
CEN 42000, 250 Alusuisse Contal, 220 BS MAG-E-121M, 308
NF A-S7G03, 257 CEN 7010, 199 DIN 3.5612, 297
NF A-S7G06, 257 LW 3.5114 DIN (D) [Me] ~ NF G-A6Z1, 306
LM27 (UK) [Ae] ~ ASTM ZH62A, 314 M1 (Prop.) [Mw] ~
CEN 46600, 253 BS MAG9, 310 Magnesium Elecktron AZ61, 301
LM28 (UK) [Ae] ~ LW 3.5164 DIN (D) [Me] ~ M1 - Mag.Elek (Prop.) [Mw] ~
AA 393.2,241 ASTM QE22A, 312 AECMA MG-P-63, 311
VAW Veral Si18CuNiMg(H), 294 BS MAG13, 310 ASTM AZ61A, 301
ASTMAZ91C, 303 BS MAG-E-121M, 308
LM30 (UK) [Ae] ~
ASTM AZ91D, 303 DIN 3.5612, 297
AAA390.1,263
BS MAG3, 309 NF G-A6Z1, 306
Valfond A-S17U4G, 259
VAW Veral Si17Cu4Mg(H), 294 DIN Wk. 3.5912, 297 M10 (Prop.) [Mw] ~
NF G-A9Z1, 306 DIN Wk. 3.5003, 297
LM31 (UK) [Ae] ~ RIMAAZ91C, 303
AA 712.0,244 M10100 UNS (USA) [Me] ~
LW 3.6104 DIN (D) [Me] ~ ASTM AM100A, 298
LM Star 1084 (Prop.) [Aw] ~ AECMA MG-C-43, 311
AA 8011, 207 M10410 UNS (USA) [Me] ~
ASTM ZE41A, 314 ASTM AS41A, 300
LM Star 1085 (Prop.) [Aw] ~ BS MAG5, 310 ASTM AS41 B, 300
AA 8021A, 208 DIN Wk. 3.5101, 297
M10600 UNS (USA) [Me] ~
LM Star 1201 (Prop) [Aw] ~ NF G-Z4TR, 306
ASTM AM60A, 299
AA 1200, 156 LW 3.6204 DIN (D) [Me] ~ ASTM AM60B, 299
CEN 1200, 156 AECMA MG-C-91, 311
M11100 UNS (USA) [Mw] ~
LM Star 1602 (Prop) [Aw] ~ ASTM EZ33A, 306
ASTM AZ1 OA, 300
AA 1060, 152 BS MAG6, 310
DIN Wk. 3.5103, 297 M11210 UNS (USA) [Mw] ~
LM Star 3103 (Prop.) [Aw] ~
ASTM AZ21X1, 300
AA 3003, 166 LW 3.6254 DIN (D) [Me] ~
CEN 3003, 167 ASTM HZ32A, 307 M11311 UNS (USA) [Mw] ~
NF 3003, 167 BS MAG8, 310 ASTM AZ31 B, 301
Comeca AZ31 B, 301
LM Star 8101 (Prop.) [Aw] ~ LW 3.7024 DIN (D) [Tw] ~
Magnesium Elektron AZ31, 300
AA 8014,208 BS 2TA1, 317
CEN Ti P99001, 341 M11312 UNS (USA) [Mw] ~
Lockalloy (Prop.) [8w] ~
Timetal 35A, 322 ASTM AZ31C, 301
Brush Wellman AlbeMet AM162 Extruded
Bar, 345 LW 3.7034 DIN (D) [Te] ~
Brush Wellman AlbeMet AM162 Rolled NF T 40,336
Sheet, 345 LW 3.7034 DIN (D) [Tew] ~
L T 24 - Tikrutan (Prop.) [Tw] ~ Timetal 50A, 323
DIN Wk. 3.7145, 319
Alloy Cross-Reference Listing 489
M11610 UNS (USA) [Mw]-+ M16600 UNS (USA) [Mw]-+ MAG4 (UK) [Me] -+
AECMA MG-P-63, 311 ASTM ZK60A, 315 ASTM ZK51A, 314
ASTM AZ61A, 301 BS MAG-x-161, 309 BS MAG4, 310
BS MAG-E-121 M, 308 DIN Wk. 3.5161,297 MAG5-T5/TE (UK) [Me] -+
DIN 3.5612, 297 NF G-Z5Zr, 306 AECMA MG-C-43, 311
Magnesium Elecktron AZ61 , 301 M16610 UNS (USA) [Me]-+ ASTM ZE41A, 314
NF G-A6Z1, 306 ASTM ZK61A, 315 BS MAG5, 310
M11630 UNS (USA) [Me]-+ M16620 UNS (USA) [Me] -+ DIN Wk. 3.5101,297
ASTM AZ63A, 302 ASTM ZH62A, 314 Magnesium Elektron ZE41, 305
M11800 UNS (USA) [Mw]-+ BS MAG9, 310 NF G-Z4TR, 306
ASTM Al80A, 302 M16630 UNS (USA) [Me]-+ MAG6-T5/TE (UK) [Me] -+
BS 2L121, 297 ASTM ZE63A, 314 AECMA MG-C-91, 311
CEN MG-P-61, 311
M16631 UNS (USA) [Me]-+ ASTM EZ33A, 306
DIN 3.5812, 297
ASTM ZC63A, 313 BS MAG6, 310
Magnesium Elektron Al80, 302 DIN Wk. 3.5103, 297
Magnesium Elektron ZC63, 305
NF G-A?Z1, 306 Magnesium Elektron EZ33, 304
M16710 UNS (USA) [Mew]-+
NF G-A8Z, 306 MAG7 (UK) [Me] -+
ASTM ZC?1A, 314
M11810 UNS (USA) [Me]-+ BS MAG?, 310
ASTM AZ81A, 302 M16710 UNS (USA) [Mw]-+ Magnesium Elektron AZ91, 302
ASTM ZC?1, 313
M11910 UNS (USA) [Me]-+ MAG8-T5/TE (UK) [Me]-+
Magnesium Elektron ZC?1, 313
ASTM AZ91 A, 303 ASTM HZ32A, 307
M18010 UNS (USA) [Me]-+
M11912 UNS (USA) [Me]-+ MAG8-T6/TE (UK) [Me]-+
ASTM K1A, 307
ASTM AZ91 B, 303 BS MAG8, 310
1V118220 UNS (USA) [Me] -+
M11914 UNS (USA) [Me]-+ MAG9-T5/TE (UK) [Me]-+
ASTM OE22A, 312
ASTM AZ91 C, 303 Magnesium Elektron OE22, 304 ASTM ZH62A, 314
BS MAG3, 309 BS MAG9, 310
DIN Wk. 3.5912, 297 M18330 UNS (USA) [Me]-+
Magnesium Elektron E021, 304 MAG12-T6 (UK) [Me]-+
NF G-A9Z1, 306 ASTM QE22A, 312
RIMA AZ91 C, 303 M18410 UNS (USA) [Mew] -+ BS MAG12, 310
M11916 UNS (USA) [Me]-+ ASTM WE54A, 313
MAG12-TF (UK) [Me]-+
ASTM AZ91 D, 303 Magnesium Elektron WE54, 305
AECMA MG-C-51, 311
M11920 UNS (USA) [Me]-+ M18430 UNS (USA) [Mew] -+ Magnesium Elektron MSR-B, 312
ASTM AZ92A, 304 ASTM WE43A, 313 NF G-Ag2.5TR. 306
Magnesium Elektron WE43, 305
M11921 UNS (USA) [Me]-+ MAG13-T6 (UK) [Me] -+
ASTM AZ91 E, 303 MA30 - Otto Fuchs (Prop.) [Mw] -+ ASTM E021A, 305
ASTMAZ31B,301
M12230 UNS (USA) [Me]-+ MAG13-TF (UK) [Me] -+
AECMA MG-C-91, 311 MA39 - Otto Fuchs (Prop.) [Mw] -+ Magnesium Elektron E021, 304
ASTM EZ33A, 306 Comeca AZ31 B, 301
MAG14-TF/T6 (UK) [Mew]-+
BS MAG6, 310 Magnesium Elektron Al31, 300
ASTM WE54A, 313
DIN Wk. 3.5103, 297 MA64 - Otto Fuchs (Prop.) [Mw]-+ Magnesium Elektron WE54, 305
Magnesium Elektron EZ33, 304 AECMA MG-P-63, 311
ASTM AZ61 A, 301 MAG-111 (UK) [Mw]-+
M13210 UNS (USA) [Mw]-+ ASTM AZ31C, 301
ASTM HM21A, 307 BS MAG-E-121M, 308
DIN 3.5612, 297 MAG151M (UK) [Mw]-+
M13310 UNS (USA) [Mew] -+ Magnesium Elektron ZW3, 315
Magnesium Elecktron AZ61, 301
ASTM HK31A, 307 Magnesium Elektron ZW3, 315
NF G-A6Z1, 306
M13312 UNS (USA) [Mw] -+ MAG-E-1 01 M (UK) [Mw] -+
MAG1 (UK) [Me] -+
ASTM HM31A, 307 ASTM MIA, 312
AECMA MG-C-61, 311
M13320 UNS (USA) [Me]-+ ASTM AZ81, 302 BS MAG-x-101, 308
ASTM HZ32A, 307 ASTM AZ81 A, 302 MAG-E-111M (UK) [Me]-+
M13320 UNS (USA) [Me]-+ BS MAG1, 309 BS MAG-S-111O, 308
BS MAG8, 310 BS MAG2, 309 NF G-A3Z1, 306
M14142 UNS (USA) [1\.4] -+ DIN Wk. 3.5812, 297 MAG-E-111M (UK) [Mw]-+
ASTM LA141, 307 NF G-A9, 306 ASTM AZ31B, 301
UNS M14142, 308 MAG2 (UK) [Me] -+ BS MAG-x-111, 308
M15100 UNS (USA) [Mw] -+ AECMA MG-C-61, 311 Comeca AZ31 B, 301
ASTM MIA, 312 ASTM AZ81 , 302 DIN 3.5312, 297
ASTM AZ81A, 302 Magnesium Elektron Al31, 300
M16210 UNS (USA) [Mw] -+
ASTM ZK21A, 314 BS MAG1, 309 MAG-E-121M (UK) [Mw]-+
BS MAG2, 309 AECMA MG-P-63, 311
M16330 UNS (USA) [Me]-+ DIN Wk. 3.5812, 297 ASTM Al61A, 301
ASTM E021A, 305 NF G-A9, 306 BS MAG-E-121M, 308
M16400 UNS (USA) [Mw] -+ MAG3 (UK) [Me] -+ BS MAG-x-121, 308
ASTM ZK40A, 314 ASTM AZ91A, 303 DIN 3.5612, 297
M16410 UNS (USA) [Me] -+ ASTM AZ91 B, 303 Magnesium Elektron AZ61, 301
AECMA MG-C-43, 311 ASTM AZ91C, 303 Magnesium Elektron AZM, 304
ASTM ZE41A, 314 ASTM AZ91 D, 303 NF G-A6Z1, 306
BS MAG5, 310 ASTM AZ91 E, 303 MAG-E-131M (UK) [Mw]-+
DIN Wk. 3.5101, 297 BS MAG3, 309 ASTM ZM21, 315
Magnesium Elektron ZE41, 305 BS MAG?, 310 BS MAG-x-131, 308
NF G-Z4TR, 306 DIN Wk. 3.5912, 297 Magnesium Elektron ZM21, 305
M16510 UNS (USA) [Me]-+ Magnesium Elektron AZ91, 302 MAG-E-141M (UK) [Mw] -+
ASTM ZK51A, 314 NF G-A9Z1, 306 BS MAG-x-141, 309
BS MAG4, 310 RIMA Al91 C, 303
490 Alloy Cross-Reference Listing
MAG-E-151M (UK) [Mw]-+ Mag Corp AZS1A (Prop.) [Me] -+ Mag. Elek AZ91 (Prop.) [Me] -+
AECMA MG-P-43, 311 AECMA MG-C-61, 311 ASTM AZ91A, 303
BS MAG-x-151, 309 ASTM AZ81A, 302 ASTM AZ91 B, 303
Magnesium Elektron ZVV3, 315 BS MAG1, 309 ASTM AZ91 C, 303
Magnesium Elektron ZVV3, 315 BS MAG2, 309 ASTM AZ91 D, 303
MAG-E-161 (UK) [Me]-+ DIN Wk. 3.5812, 297 BS MAG3, 309
ASTM ZK61A, 315 NF G-A9, 306 BS MAG?, 310
MAG-E-161 (UK) [Mw] -+ Mag Corp AZ91D (Prop.) [Me] -+ DIN Wk. 3.5912, 297
ASTM ZK60A, 315 ASTM AZ91D. 303 Magnesium Elektron AZ91, 302
BS MAG-x-161 , 309 NF G-A9Z1, 306
Mag Corp AZ91E (Prop) [Me]-+
DIN Wk. 3.5161, 297 ASTM AZ91 E, 303 RIMA AZ91C. 303
NF G-Z5Zr, 306 Mag Corp 'MAXMAG' (Prop.) [Me] -+ Mag. Elek AZ855 (Prop.) [Mw] -+
ASTM AZ80A, 302
MAG-F-121 (UK) [Mw]-+ ASTM M1C, 308
AECMA MG-P-63, 311 Mag. Elek AS (Prop.) [Me] -+ Mag. Elek AZG (Prop) [Me] -+
ASTM AZ61A, 301 AECMA MG-C-61, 311 ASTM AZ63A, 302
BS MAG-E-121M, 308 ASTM AZ81A, 302 Mag. Elek AZM (Prop.) [Mw] -+
DIN 3.5612, 297 BS MAG1, 309 AECMA MG-P-63. 311
NF G-A6Z1, 306 BS MAG2, 309 ASTM AZ61 A, 301
MAG-F-121M (UK) [Mw]-+ DIN Wk. 3.5812, 297 BS MAG-E-121M. 308
BS MAG-x-121, 308 NF G-A9, 306 BS MAG-x-121. 308
Magnesium Elektron AZ61, 301 Mag. Elek AE42 (Prop) [Me] -+ DIN 3.5612, 297
Magnesium Elektron AZM, 304 Hydro Magnesium AE42, 298 NF G-A6Z1 306
MAG-F-131M (UK) [Mw]-+ Mag. Elek AM20 (Prop.) [Me] -+ Mag. Elek C-alioy (Prop) [Me] -+
ASTM ZM21, 315 ASTM AM20, 298 BS MAG?, 310
Magnesium Elektron ZM21, 305 Hydro Magnesium AM20, 298 Mag. Elek EQ21 (Prop) [Me] -+
MAG-F-151M (UK) [Mw]-+ Mag. Elek AM50 (Prop.) [Me] -+ ASTM EQ21A, 305
AECMA MG-P-43, 311 ASTM AM50A, 298 Mag. Elek EZ33 (Prop.) [Me] -+
BS MAG-x-151, 309 ASTM AM50B, 298 AECMA MG-C-91, 311
Magnesium Elektron ZVV3, 315 ASTM EZ33A 306
Mag. Elek AM60 (Prop.) [Me] -+
Magnesium Elektron ZVV3, 315
ASTM AM60, 299 BS MAG6, 310
MAG-S-101M (UK) [Mw]-+ DIN Wk. 3.5103. 297
Mag. Elek AM503 (Prop.) [Mw]-+
BS MAG-x-1 01, 308
ASTM MIA, 312 Mag. Elek HK31 (Prop.) [Mew] -+
MAG-S-111M (UK) [Mw]-+ ASTM HK31A, 307
BS MAG-x-101, 308
BS MAG-x-111, 308 Mag. Elek M1 (Prop.) [Mw] -+
Mag. Elek AS21 (Prop.) [Me] -+
MAG-S-1110 (UK) [Me]-+ AECMA MG-P-63, 311
ASTM AS21, 299
BS MAG-S-111 0, 308 Hydro Magnesium AS21, 299 ASTM AZ61A, 301
NF G-A3Z1, 306 BS MAG-E-121M, 308
Mag. Elek AS41 (Prop.) [Me]-+ DIN 3.5612, 29?
MAG-S-1110 (UK) [Mw]-+ ASTM AS41A, 300 NF G-A6Z1, 306
ASTM AZ31 B, 301
Mag. Elek AZ31 (Prop.) [Me] -+ Mag. Elek MSR (Prop) [Me] -+
BS MAG-x-111, 308
BS MAG-S-111 0, 308 Magnesium Elektron QE22, 304
Comeea AZ31 B, 301 NF G-A3Z1, 306
DIN 3.5312, 297 Mag. Elek MSR-A (Prop.) [Me] -+
Magnesium Elektron AZ31, 300 Mag. Elek AZ31 (Prop.) [Mw]-+ Magnesium Elektron MSR-A, 312
ASTM AZ31 B, 301
MAG-S-131M (UK) [Mw]-+ Mag. Elek MSR-B (Prop.) [Me] -+
ASTM AZ31C, 301
ASTMZM21,315 AECMA MG-C-51, 311
BS MAG-x-111, 308
BS MAG-x-131, 308 BS MAG12, 310
DIN 3.5312, 297
Magnesium Elektron MSR-B, 312
MAG-S-1310 (UK) [Mw]-+ Mag. Elek AZ61 (Prop.) [Mw] -+ NF G-Ag2.5TR, 306
ASTMZM21,315
ASTM AZ61A, 301
BS MAG-x-131, 308 Mag. Elek MTZ (Prop.) [Mew] -+
BS MAG-x-121, 308
ASTM HK31A, 307
MAG-S-1310/M (UK) [Mw]-+ Mag. Elek AZSO (Prop.) [Mw] -+
Magnesium Elektron ZM21, 305 Mag. Elek QE22 (MSR) (Prop.) [Me] -+
ASTM AZ80A, 302
MAG-S-141M (UK) [Mw]-+ ASTM OE22A, 312
BS 2L 121,297
BS MAG-x-141 , 309 BS MAG13, 310
CEN MG-P-61, 311
MAG-S-151 (UK) [Mw] -+ DIN 3.5812, 297 Mag. Elek QE22A (MSR-B) (Prop.) [Me] -+
AECMA MG-P-43, 311 Magnesium Elektron AZ80, 302 ASTM QE22A, 312
Magnesium Elektron ZVV3, 315 NF G-A?Z1, 306 Mag. Elek QH21A (Prop.) [Me]-+
Magnesium Elektron ZVV3, 315 NF G-A8Z, 306 ASTM OH21A, 313
MAG-S-151M (UK) [Mw]-+ Mag. Elek AZS1 (Prop.) [Me] -+ Mag. Elek RZ5 (Prop.) [Me] -+
BS MAG-x-151, 309 AECMA MG-C-61, 311 AECMA MG-C-43, 311
MAG-T-101M (UK) [Mw]-+ ASTM AZ81 , 302 ASTM ZE41A, 314
ASTM MIA, 312 ASTM AZ81A, 302 BS MAG5, 310
BS MAG1, 309 DIN Wk. 3.5101, 297
MAG-T-111M (UK) [Mw]-+
BS MAG2, 309 NF G-Z4TR, 306
ASTM AZ31B, 301
DIN Wk. 3.5812, 297 Mag. Elek TZ6 (Prop.) [Me] -+
MAG-T-121M (UK) [Mw]-+ NF G-A9, 306 ASTM ZH62A, 314
AECMA MG-P-63, 311
BS MAG9, 310
ASTM AZ61A, 301
BS MAG-E-121M, 308 Mag. Elek W2 (welding rod) (Prop.) [Mw] -+
DIN 3.5612, 297 ASTM MIA, 312
Magnesium Eleektron AZ61, 301 Mag. Elek W5 (welding rod) (Prop.) [Mw]-+
NF G-A6Z1, 306 ASTM ZM21, 315
Mag Corp AM50A (Prop.) [Me]-+
ASTM AM50A, 298
Mag Corp AM60B (Prop.) [Me] -+
ASTM AM60B, 299
Alloy Cross-Reference Listing 491
Mag. Elek W6 (welding rod) (Prop) [Me) ~ Mag. Elek ZW1 (Prop.) [Mw) ~ MgAI6 DIN (D) [Me) ~
AECMA MG-C-91, 311 BS MAG-x-141, 309 ASTM AM60, 299
ASTM EZ33A, 306 Mag. Elek ZW3 (Prop.) [Mw) ~ ASTM AM60A, 299
BS MAG6, 310 AECMA MG-P-43, 311 MgAI6Zn DIN (D) [Mw) ~
DIN Wk. 3.5103, 297 BS MAG-x-151, 309 AECMA MG-P-63, 311
Mag. Elek W7(welding rod) (Prop.) [Me) ~ Magnesium Elektron ZW3, 315 ASTM AZ61A, 301
AECMA MG-C-43, 311 Mag. Elek ZW6 (Prop) [Me) ~ BS MAG-E-121M, 308
ASTMZE41A,314 ASTM ZK61A, 315 DIN 3.5612, 297
BS MAG5, 310 ASTM ZK60A, 315 NF G-A6Z1, 306
DIN Wk. 3.5101, 297 BS MAG-x-161, 309 Mg-AI6Zn1 DIN (D) [Me) ~
NF G-Z4TR, 306 DIN Wk. 3.5161, 297 ASTM AM60, 299
Mag. Elek W8 (welding rod) (Prop.) [Me) ~ NF G-Z5Zr, 306 MgAI8Zn DIN (D) [Mw) ~
ASTM QE22A, 312 MAM 4427, [Mew] ~ ASTM AZ80A, 302
Mag. Elek W9 (welding rod) (Prop.) [Me) ~ Magnesium Elektron WE43, 305 BS 2L 121,297
ASTM ZE63A, 314 Mangal (Prop.) [Aw) ~ CEN MG-P-61, 311
Mag. Elek W13 (welding rod) (Prop.)[Me)~ AA 3103, 169 DIN 3.5812, 297
Magnesium Elektron MSR-B, 312 CEN 3103, 169 Magnesium Elektron AZ80, 302
NF G-A7Z1, 306
Mag. Elek W14 (welding rod) (Prop.)[Me)~ MAXMAG - Mag Corp (Prop.) [Me) ~
NF G-A8Z, 306
ASTM AZ81 , 302 ASTM M1C, 308
BS MAG7, 310 MC10 CSA (Can) [Aw) ~ MgAI8Zn1 DIN (D) [Me) ~
Magnesium Elektron AZ91, 302 AECMA MG-C-61, 311
AA 3003,166
ASTM AZ81, 302
Mag. Elek W15 (welding rod) (Prop) [Mw) Alusuisse Aluman 100, 213
~ CEN 3003, 167 ASTM AZ81A, 302
Comeca AZ31 B, 301 Hoogovens 3530, 170 BS MAG1, 309
Magnesium Elektron AZ31, 300 BS MAG2, 309
Lawson Mardon (LM) Star 3103, 169
DIN Wk. 3.5812, 297
Mag. Elek W19 (welding rod) (Prop.) [Me) NF 3003, 167
Reynolds Tread-Brite, 228 NF G-A9, 306
~
ASTM EQ21A, 305 VAW 41/20, 148 Mg-AI9Zn DIN (D) [Me) ~
ASTM AZ91D, 303
Mag. Elek W21 (welding rod) (Prop.) [Me) Menziken code 1100 (Prop.) [Aw) ~
~ Alusuisse Pure Aluminium 99.0, 226 Mg-AI9Zn ISO (EUR) [Me) ~
Magnesium Elektron ZC63, 305 Menziken code 2102 (Prop.) [Aw) ~ ASTM AZ91D, 303
Mag. Elek W22 (welding rod) (Prop.) [Mw) Alusuisse Avional-102, 218 MgAI19Zn1 DIN (D) [Me) ~
BS MAG7, 310
~ Menziken code 2118 (Prop.) [Aw) ~
ASTM ZC71, 313 Magnesium Elektron AZ91, 302
AlusuisseAvional Pb-118, 219
Mag. Elek W23 (welding rod) (Prop.) [Mew) MG-C-41 AECMA (EUR) [Me) ~
Menziken code 2500 (Prop.) [Aw] ~
~ Alusuisse Decoltal 500, 220 ASTM ZH62A, 314
Magnesium Elektron WE54, 305 BS MAG9, 310
Menziken code 2660 (Prop.) [Aw] ~
Mag. Elek WE43 (Prop.) [Mew) ~ Alusuisse Avional-660/662, 219 MG-C-43 AECMA (EUR) [Me) ~
ASTM WE43A, 313 AECMA MG-C-43, 311
Menziken code 2662 (Prop.) [Aw] ~ ASTM ZE41A, 314
Mag. Elek WE54 (Prop.) [Me) ~ Alusuisse Avional-660/662, 219 BS MAG5, 310
BS MAG14, 311 Menziken code 5150 (Prop.) [Aw] ~ DIN Wk. 3.5101, 297
Mag. Elek WE54 (Prop.) [Mew) ~ Alusuisse Peraluman 150/151, 223 Magnesium Elektron ZE41, 305
ASTM WE54A, 313 Menziken code 5151 (Prop.) [Aw] ~ NF G-Z4TR, 306
Magnesium Elektron WE54. 305 Alusuisse Peraluman 150/151, 223 MG-C-43 CEN (EUR) [Me] ~
Mag. Elek Z5Z (Prop.) [Me) ~ Menziken code 5253 (Prop.) [Aw) ~ AECMA MG-C-43, 311
ASTM ZK51A, 314 Alusuisse Peraluman 253, 224 ASTM ZE41A, 314
BS MAG4, 310 BS MAG5, 310
Menziken code 6041 (Prop.) [Aw) ~
Mag. Elek ZC63 (Prop.) [Me) ~ Alusuisse Anticorodal-041 , 215 DIN Wk. 3.5101, 297
ASTM ZC63A, 313 NF G-Z4TR, 306
Menziken code 6043 (Prop.) [Aw) ~
Mag. Elek ZC71 (Prop.) [Mew) ~ Alusuisse Extrudal-043, 221 MG-C-51 AECMA (EUR) [Me) ~
ASTM ZC71A, 314 AECMA MG-C-51 , 311
Menziken code 6050 (Prop.) [Aw) ~
Mag. Elek ZC71 (Prop.) [Mw) ~ ASTM QE22A, 312
Aiusuisse Extrudal-050, 221
Magnesium Elektron ZC71, 313 BS MAG12, 310
Menziken code 6080 (Prop.) [Aw] ~ Magnesium Elektron MSR-B, 312
Mag. Elek ZCM711 (Prop.) [Mw) ~ Alusuisse Anticorodal-082, 216
ASTM ZC71, 313 NF G-Ag25TR, 306
Menziken code 6082 (Prop.) [Aw] ~ MG-C-51 CEN (EUR) [Me] ~
Mag. Elek ZE41 (Prop.) [Me) ~ Alusuisse Anticorodal-082, 216
AECMA MG-C-43, 311 AECMA MG-C-51, 311
ASTM ZE41A, 314 Menziken code 6100 (Prop.) [Aw] ~ BS MAG12, 310
BS MAG5, 310 Alusuisse Anticorodal-1 00/1 05, 216 Magnesium Elektron MSR-B, 312
DIN Wk. 3.5101, 297 Menziken code 6107 (Prop.) [Aw) ~ NF G-Ag2.5TR, 306
NF G-Z4TR, 306 Alusuisse Anticorodal Pb-107, 217 MG-C-61 AECMA (EUR) [Me) ~
Mag. Elek ZE63 (Prop.) [Me] ~ Menziken code 6109 (Prop) [Aw) ~ AECMA MG-C-61 , 311
ASTM ZE63A, 314 Alusuisse Anticorodal Pb-1 09, 217 ASTM AZ81 A, 302
MG20 - Otto Fuchs (Prop.) [Mw) ~ BS MAG1, 309
Mag. Elek ZM21 (Prop.) [Mw] ~ BS MAG2, 309
ASTM ZM21, 315 ASTM MIA, 312
DIN Wk. 3.5812, 297
BS MAG-x-131, 308 MgAI3Zn DIN (D) [Me) ~ NF G-A9, 306
Mag. Elek ZRE1 (Prop) [Me) ~ BS MAG-S-111O, 308
NF G-A3Z1, 306 MG-C71 CEN (EUR) [Mew) ~
AECMA MG-C-91, 311
ASTM AZ31B, 301 ASTM ZC71A, 314
ASTM EZ33A, 306 ASTMZC71,313
BS MAG6, 310 Comeca AZ31 B. 301
DIN 3.5312, 297 Magnesium Elektron ZC71, 313
DIN Wk. 3.5103, 297
Mag. Elek ZT1 (Prop.) [Me) ~ Magnesium Elektron AZ31, 300
ASTM HZ32A, 307
492 Alloy Cross-Reference Listing
Mg-C71 NF (F) [Mew] -+ MIA ASTM (USA) [Mw] -+ MIL-M-46062B (USA) [Me] -+
ASTM ZC71A, 314 ASTM MIA, 312 ASTM QE22A, 312
ASTM ZC71, 313 BS MAG-x-101, 308 ASTM ZE63A, 314
Magnesium Elektron ZC71, 313 MIL-9046/9047: CP2 (USA) [Tw] -+ BS MAG9, 310
MG-C-81 AECMA (EUR) [Me] -+ ASTM Grade 3, 332 MIL-M-46130 (USA) [M]-+
ASTM HZ32A, 307 MIL-A-21180 (USA) [Ae] -+ ASTM LA141, 307
BS MAG8, 310 AA 354.0, 238 UNS M14142, 308
MG-C-91 AECMA (EUR) [Me] -+ AA 359.0, 239 MIL-P-25995 (USA) [Aw] -+
AECMA MG-C-91 , 311 AA A201 ,0, 261 AA 6061, 191
ASTM EZ33A, 306 AA A356.0, 262 CEN 6061, 192
BS MAG6, 310 AA A357,0, 262 MIL-R-6944 (USA) [Me] -+
DIN Wk, 3,5103, 297 AA C355,0, 277 ASTM EZ33A, 306
Magnesium Elektron EZ33, 304 MIL-A-22771 (USA) [Aw] -+ MIL-R-81588 (USA) [Tw] -+
MG-C-91 CEN (EUR) [Me] -+ AA 2014, 159 AMS 4915,327
AECMA MG-C-91, 311 AA 2618, 165 MIL R-81588, 334
ASTM EZ33A, 306 AA6061,191 Timetal 8-1-1, 322
BS MAG6, 310 AA6151,197
MIL-T-9046 (USA) [Tew] -+
DIN Wk, 3,5103, 297 AA 7050,202
3620-TA7, 326
MG-C-960 AECMA (EUR) [Mew] -+ AA 7075,203
Beta C, 330
ASTM WE43A, 313 AA 7175,205
NF TA6V, 336
ASTM WE54A, 313 CEN 2014, 160
Timetal 6-4, 321
MG-C64001 AECMA (EUR) [Me] -+ CEN 6061, 192
Timetal 65A, 323
ASTM EQ21A, 305 CEN 7050, 202
CEN 7075, 204 MIL-T-9046 (USA) [Tw]-+
Magnesium Elektron EQ21, 304 Ti-13V-l1Cr-3AI,339
CEN 7175, 206
MG-C96001 AECMA (EUR) [Mew] -+ Ti-8Mo-8V-2Fe-3AI, 338
ASTM WE54A, 313 MIL-A-46192 (USA) [Aw]-+
AMS 4905, 326
Magnesium Elektron WE54, 305 AA2519,165
AMS 4910,327
MG-C96002 AECMA (EUR) [Mew] -+ MILC-5 (USA) [Tw]-+ AMS 4917,327
ASTM WE43A, 313 Teledyne Allvac 8-1-1 , 329 AMS 4926, 328
Magnesium Elektron WE43, 305 MIL-F-83142 (USA) [Tew] -+ ASTM Grade 4, 332
MG-P-43 AECMA (EUR) [Mw] -+ Beta C, 330 ASTM Grade 5, 333
AECMA MG-P-43, 311 NFTA6V, 336 ASTM Grade 5,333
BS MAG-x-151, 309 Timetal 6-4, 321 ASTM Grade 6, 333
Magnesium Elektron ZW3, 315 MIL-F83142 (USA) [Tw] -+ BS 2TA10, 317
CEN Ti P63, 340
MG-P-61 AECMA (EUR) [Mw] -+ Ti-13V-l1Cr-3AI,339
CEN Ti P99002, 341
ASTM AZ80A, 302 Ti-8Mo-8V-2Fe-3AI, 338
AMS 4905, 326 CEN Ti P99003, 341
BS 2L 121,297 Crucible Steel Co, B 120 VCA, 330
CEN MG-P-61, 311 AMS 4917, 327
ASTM Grade 5, 333 Deutsche Titan Tikrutan LT 31, 342
DIN 3,5812,297 Deutsche Titan Tikrutan RT 15, 343
Magnesium Elektron AZ80, 302 BS 2TA10, 317
CEN Ti P63, 340 Deutsche Titan Tikrutan RT 18, 343
NF G-A7Z1, 306 Deutsche Titan Tikrutan RT 20, 343
NF G-A8Z, 306 Crucible Steel Co, B 120 VCA, 330
Deutsche Titan Tikrutan LT 31, 342 DIN LW 3.7164, 319
MG-P-61 CEN (EUR) [Mw] -+ DIN LW 3,7164, 319 DIN Ti AI6 V4, 339
CEN MG-P-61, 311 DIN Ti AI6 V4, 339 DIN Wk, 3,7055, 318
MG-P-62 AECMA (EUR) [Me] -+ DIN Wk, 3,7165, 320 DINWk, 3.7065, 318
BS MAG-S-ll10, 308 DTD 5163,328 DIN Wk. 3.7115, 318
NF G-A3Z1, 306 NF Ti P64001, 340 DIN Wk, 3.7165, 320
MG-P-62 AECMA (EUR) [Mw] -+ UNS R58640, 335 DTD 5083, 328
ASTM AZ31 B, 301 UNS R58820, 335 DTD 5163, 328
NF TA 5E, 336
Comeca AZ31B, 301 MIL-M38B (USA) [Me] -+
DIN 3,5312, 297 NF Ti P64001 , 340
ASTMAZ91B,303
Magnesium Elektron AZ31, 300 Timetal 75A, 323
MIL-M-8916 (USA) [Mw]-+ UNS R58640, 335
MG-P-63 AECMA (EUR) [Mw] -+ ASTM HM31A, 307 UNS R58820, 335
AECMA MG-P-63, 311 MIL-M-8917 (USA) [Mw]-+
ASTM AZ61A, 301 MIL-T-9046: AB4 (USA) [Tw]-+
ASTM HM21A, 307 Titanium Industries Ti-6-2-4-2, 338
BS MAG-E-121M, 308
MIL-M-26075 (USA) [Mew] -+ MIL-T-9046/9047: CP1 (USA) [Tew]-+
DIN 3,5612, 297
ASTM HK31A, 307 ASTM Grade 4, 333
Magnesium Elecktron AZ61, 301
NF G-A6Z1, 306 MIL-M-46039 (USA) [Mw] -+ Titanium Industries GR-4, 331
ASTM ZK21A, 314
MgZn6Zr DIN (D) [Me] -+ MIL-T-9046: CP2 (USA) [Tew]-+
ASTM ZK61A, 315 MIL-M-46062 (USA) [Me] -+ Titanium Industries GR-3, 331
ASTM ZK60A, 315 ASTM AZ91 C, 303 MIL-T-9046: CP3 (USA) [Tew]-+
BS MAG-x-161, 309 ASTM AZ92A, 304 Titanium Industries GR-2, 331
DIN Wk, 3.5161,297 ASTM EQ21A, 305
MIL-T-9046: CP3 (USA) [Tw]-+
NF G-Z5Zr, 306 ASTM HZ32A, 307
ASTM Grade 2, 332
ASTM ZH62A, 314
MgZnReZr ISO (EUR) [Me] -+ MIL-T-9046: CP4 (USA) [Tw] -+
ASTM ZK51A, 314
AECMA MG-C-43, 311 ASTM Grade 1, 332
ASTM ZE41A, 314 BS MAG4, 310
Magnesium Elektron ZE41, 305 Titanium Industries GR-1, 331
BS MAG5, 310
RIMA AZ91 C, 303 MIL-T-9046/9047: CP-70 (USA) [Tew]-+
DINWk, 3,5101, 297
NF G-Z4TR, 306 MIL-M-46062 (USA) [Mew] -+ ASTM Grade 4, 333
ASTM HK31A, 307 Titanium Industries GR-4, 331
Mg-Zn RE Zr 2119/3115 ISO (EUR) [Me] -+
Magnesium Elektron ZE41, 305 MIL-M-46062A (USA) [Me] -+
BS MAG13, 310
Magnesium Elektron QE22, 304
Alloy Cross-Reference Listing 493
MIL-T-9047 (USA) [Tew] + MIL-T81915 (USA) [Tw] + N8 (NS 8) (UK) [Aw]+
Beta C, 330 AMS 4905,326 AA 5083,178
NFTA6V, 336 ASTM Grade 5, 333 Alusuisse Peraluman-460/462, 225
Timetal 6-4, 321 BS 2TA10, 317 Alusuisse Peraluman-462, 225
MIL-T-9047 (USA) [Tw] + CEN Ti P63, 340 CEN 5083, 179
Ti-13V-11Cr-3AI,339 Deutsche Titan Tikrutan LT 31, 342 Hoogovens 5510, 185
Ti-8Mo-8V-2Fe-3AI, 338 DIN LW 3.7164, 319 Superform Metals 5083 SPF, 179
AMS 4905, 326 DIN Ti AI6 V4, 339 N21 (UK) [Aw]+
AMS 4917, 327 DIN Wk. 3.7165, 320 AA 4047A, 173
ASTM Grade 4, 332 DTD 5163, 328 CEN 4047A, 173
ASTM Grade 5, 333 NF Ti P64001, 340
N31 (UK) [Aw]+
BS 2TA10, 317 MIL-Ti-Cp-70 C-1 (USA) [Tw] + AA 3105, 170
CEN Ti P63, 340 Teledyne Allvac 70, 329 CEN 3105, 170
CEN Ti P99003, 341 MSR - Mag. Elek. (Prop.) [Me] + VAW61/10, 148
Crucible Steel Co. B 120 VCA, 330 Magnesium Elektron QE22, 304 N41 (UK) [Aw] +
Deutsche Titan Tikrutan LT 31, 342
Deutsche Titan Tikrutan RT 20, 343
MSR-A - Mag. Elek. (Prop.) [Me] + AA 5005,174
Magnesium Elektron MSR-A, 312 AA 5005A, 174
DIN LW. 3.7164, 319
DIN Ti AI6 V4, 339 MSR-B NF (F) [Me] + Alusingen 214, 150
ASTM QE22A, 312 Alusuisse Peraluman-100 (101), 223
DIN Wk. 3.7065, 318
BS MAG12, 310 CEN 5005, 174
DIN Wk. 3.7165, 320
DTD 5163,328 MSR-B - Mag. Elek. (Prop.) [Me] + DIN AI Mg1, 212
DIN Wk. 3.3315 (AIMg1), 146
NF Ti P64001, 340 AECMA MG-C-51, 311
Hoogovens 5010, 174
Timetal 75A, 323 BS MAG12, 310
UNS R58640, 335 NF G-Ag2.5TR, 306 N51 (UK) [Aw]+
UNS R58820, 335 MTZ - Mag. Elek. (Prop.) [Mew] + AA 5454,184
Alusuisse Peraluman-260, 224
MIL-T-9047: AB4 (USA) [Tw] + ASTM HK31A, 307
CEN 5454, 185
Titanium Industries Ti-6-2-4-2, 338
Hoogovens 5400, 184
MIL-T-9047 C-6 (USA) [Tw] +
Teledyne Allvac 6-4, 329
N N52 (UK) [Aw]+
AA 5554,186
MIL-T-9047 C-11 (USA) [Tw] + N2 (UK) [Aw]+ N61 (UK) [Aw]+
Teledyne Allvac 6-2-4-2, 328 AA 4047,173 AA 5456,185
MIL-T-9047 C-14 (USA) [Tw] +
Teledyne Allvac 6-2-4-6, 329
N3 (UK) [Aw]+ AA 5556A, 186
AA 3103, 169 NBN1050 (B) [Aw] +
MIL-T-9047: CP1 (USA) [Tew] + CEN 3103, 169 AA 1050, 151
ASTM Grade 4, 333 DIN AI Mn1, 213 Hoogovens 1000, 151
MIL-T-9047: CP2 (USA) [Tew] + DIN Wk. 3.0315 (AIMn1), 143 VAW 99/52, 149
Titanium Industries GR-3, 331 Hoogovens 3000, 166 NBN1200 (B) [Aw] +
MIL-T-9047: CP3 (USA) [Tew] + N4 (UK) [Aw]+ VAW99/01,149
Titanium Industries GR-2, 331 AA 5052, 177 NF A57-705 AM60 NF (F) [Me] +
MIL-T-9047: CP3 (USA) [Tw] + AA5251,182 ASTM AM60, 299
ASTM Grade 2, 332 Alusuisse Peraluman 253, 224
Alusuisse Peraluman-226, 223
+
NF L 14-633 Ti P64001 NF (F) [Tew]
MIL-T-9047: CP4 (USA) [Tw] + NF TA6V, 336
CEN 5052, 177
ASTM Grade 1, 332 Timetal 6-4, 321
CEN 5251, 183
MIL-T-9047: CP4 (USA) [Tw] + DIN Wk. 3.3523 (AIMg2.5), 146 +
NF L 14-633 Ti P64001 NF (F) [Tw]
Titanium Industries GR-1, 331 DIN Wk. 3.3526 (AIMg2MnO.3), 146 AMS 4905, 326
MIL-T-9047: CP-70 (USA) [Tew] + Hoogovens 5520, 185 ASTM Grade 5, 333
ASTM Grade 4, 333 VAW 63/52, 148 BS 2TA10, 317
MIL-T-9047 ELI C-7 (USA) [Tw] + N5 (UK) [Aw] + CEN Ti P63, 340
Deutsche Titan Tikrutan LT 31, 342
Teledyne Allvac 6-4 ELI, 329 AA 5154, 181
DIN LW. 3.7164, 319
MIL-T81556 (USA) [Tew] + AA5154A,181
DIN Ti AI6 V4, 339
NF TA6V, 336 AA 5254,183
DIN Wk. 3.7165, 320
Timetal6-4, 321 AA 5754, 187
DTD 5163,328
MIL-T81556 (USA) [Tw] + Alusingen 234, 150
NF Ti P64001, 340
Alusuisse Peraluman-300 (301), 224
AMS 4905, 326
ASTM Grade 5, 333 Alusuisse Peraluman-302, 224 NG5 (UK) [Aw] +
CEN 5154A, 181 AA5154,181
BS 2TA10, 317 DIN AIMg3.5, 212
CEN Ti P63, 340 CEN 5754, 187
Deutsche Titan Tikrutan LT 31, 342 DIN AI Mg3 EQ, 212 NS17005 (Nor) [Aw] +
DIN AIMg3.5, 212 VAW 99/01, 149
DIN LW 3.7164, 319
DIN Ti AI6 V4, 339 Hoogovens 5030, 175 NS17010 (Nor) [Aw] +
DIN Wk. 3.7165, 320 NF A-G3, 210 AA 1050, 151
DTD 5163,328 N6 (UK) [Aw] + Hoogovens 1000, 151
NF Ti P64001, 340 AA 5019, 175 VAW 99/52, 149
Teledyne Allvac 30, 329 AA 5056,177 NS3 (UK) [Aw] +
Teledyne Allvac 40, 329 AA 5056A, 178 AA 3003,166
Teledyne Allvac 55, 329 AA 5356,184 Alusuisse Aluman 100, 213
Ti-13V-11Cr-3AI,339 CEN 5019, 175 CEN 3003, 167
MIL-T81588 (USA) [Tw] + CEN 5356, 184 Hoogovens 3530, 170
AMS 4917,327 DIN Wk. 3.3555 (AIMg5), 147 Lawson Mardon (LM) Star 3103, 169
Crucible Steel Co. B 120 VCA, 330 NF 3003,167
MIL-T81915 (USA) [Tcw] + Reynolds Tread-Brite, 228
VAW 41/20, 148
NFTA6V, 336
Timetal 6-4, 321
494 Alloy Cross-Reference Listing
NS4 (UK) [Aw] ... Otto Fuchs AM54 (Prop.) [Aw] ... Otto Fuchs MA39 (Prop.) [Mw] ...
AA 5251,182 AA 5182, 181 Comeca AZ31 B, 301
Alusuisse Peraluman-226, 223 CEN 5182, 182 Magnesium Elektron AZ31, 300
CEN 5251, 183 Otto Fuchs AM 58 (Prop.) [Aw] ... Otto Fuchs MA64 (Prop.) [Mw]'"
DIN Wk. 3.3526 (AIMg2MnO.3), 146 AA 5056A, 178 AECMA MG-P-63, 311
Otto Fuchs AN40 (Prop.) [Aw] ... ASTM AZ61A, 301
o AA 2618, 165
AA 2618A, 166
BS MAG-E-121M, 308
DIN 3.5612, 297
CEN 2618A, 166 Magnesium Elecktron AZ61 , 301
Otto Fuchs A1 (Prop.) [Aw] ... NF G-A6Z1, 306
AA 1080A, 153 Otto Fuchs AS05 (Prop.) [Aw]'"
AA 6060, 190 Otto Fuchs MA84 (Prop) [Mw] ...
CEN 1080A, 153
AA 6063,193 ASTM AZ80F, 302
Otto Fuchs A2 (Prop.) [Aw] ...
AA 6063A, 193 Otto Fuchs MG20 (Prop.) [Mw] ...
AA 1070A, 153
Alunord 6060.48, 191 ASTM MIA, 312
Alunord 1370-70, 158
Alunord 6060.79, 191 Otto Fuchs R (Prop.) [Aw] ...
CEN 1070A, 153
CEN 6060, 190 DIN Wk. 3.0400, 144
Otto Fuchs AB13 (Prop.) [Aw] ... CEN 6063, 193
AA 6012, 189 Otto Fuchs R05 (Prop.) [Aw] ...
Otto Fuchs AS07 (Prop.) [Aw] ... DIN Wk. 3.3309, 146
CEN 6012, 189
AA 6005A, 188
Otto Fuchs AB27 (Prop) [Aw] ... Otto Fuchs R1 (Prop.) [Aw] ...
Alunord 6005A, 188
AA 2007, 158 DIN Wk. 3.3319, 146
Alunord 6081-11, 194
Otto Fuchs AG15 (Prop.) [Aw] ... CEN 6005A, 189 Otto Fuchs T2 (Prop.) [Tw] ...
AA 3103, 169 DIN Wk. 3.7025, 318
Otto Fuchs AS10 (Prop.) [Aw] ...
CEN 3103, 169 AA 6082,194 Otto Fuchs T3 (Prop.) [Tw] ...
Otto Fuchs AG18 (Prop.) [Aw] ... CEN 6082, 195 DIN Wk. 3.7035, 318
AA 3003,166 Otto Fuchs AS20 (Prop.) [Aw] ... Otto Fuchs T6 (Prop.) [Tw] ...
CEN 3003, 167 AA 6061,191 DIN Wk. 3.7065, 318
NF 3003, 167 CEN 6061, 192 Otto Fuchs TL35 (Prop.) [Tw] ...
Otto Fuchs AK13 (Prop.) [Aw] ... Otto Fuchs AS60 (Prop.) [Aw] ... DIN Wk. 3.7110, 318
AA 2017, 160 AA 4032,172 Otto Fuchs TL44 (Prop.) [Tw] ...
AA 2017A, 161 DIN LW 3.7184,320
Otto Fuchs AZ14 (Prop.) [Aw] ...
CEN 2017A, 161 DIN Wk. 3.7185, 320
AA 7020,200
Otto Fuchs AK24 (Prop.) [Aw] ... CEN 7020, 200 Otto Fuchs TL62 (Prop.) [Tw] ...
AA 2024, 161 AMS 4919,327
Otto Fuchs AZ54 (Prop.) [Aw] ...
CEN 2024, 162 DIN LW 3.7144,319
AA 7022,201
Otto Fuchs AK34 (Prop.) [Aw] ... AA 7079,204 UNS R56260, 334
AA 2014, 159 Otto Fuchs TL64 (Prop.) [Tw]'"
Otto Fuchs AZ62 (Prop.) [Aw] ...
CEN 2014, 160 DIN Wk. 3.7165, 320
AA 7475,206
Otto Fuchs AK60 (Prop.) [Aw] ... CEN 7475, 207 Otto Fuchs TL66 (Prop.) [Tw] ...
AA 2219, 165 DIN LW 3.7174,320
Otto Fuchs AZ64 (Prop.) [Aw] ...
CEN 2219, 165
AA 7075,203
Otto Fuchs AL 10 (Prop.) [Aw] ... CEN 7075, 204
AA 8090,209
p
Otto Fuchs AZ66 (Prop.) [Aw] ...
Otto Fuchs AL 11 (Prop.) [Aw]'" AA 7049,202
AA 8091,209 P-AICu2.5MgSi (I) [Aw] ...
AA 7149,205 AA2117,164
Otto Fuchs AL21 (Prop.) [Aw] ... CEN 7149, 205 DIN Wk. 3.1305 (AICu2.5MgO.5), 144
AA 2091,163 Otto Fuchs AZ69 (Prop.) [Aw] ... P-AICu4MgMn (I) [Aw] ...
Otto Fuchs AM10 (Prop.) [Aw]'" AA 7175,205 AA 2017, 160
AA 5005A, 174 CEN 7175, 206 Hoogovens 2170, 164
Otto Fuchs AM15 (Prop.) [Aw]'" Otto Fuchs AZ74 (Prop.) [Aw] ... P-AICu4.4SiMnMgplacc. (I) [Aw] ...
AA 5050B, 176 AA 7009,199 AA 2014 Alclad, 160
Otto Fuchs AM18 (Prop.) [Aw] ... Otto Fuchs AZ83 (Prop.) [Aw] ... P-AICu4.5MgMn (I) [Aw] ...
AA 5051A, 176 AA 7010, 199 AA2024,161
CEN 5051A, 176 CEN 7010, 199 Alusuisse Avional150, 219
Otto Fuchs AM21 (Prop.) [Aw] ... Otto Fuchs AZ84 (Prop.) [Aw] ... Alusuisse Avional152, 219
AA 5049,176 AA 7050,202 CEN 2024, 162
CEN5049, 176 AA 7150,205 DIN Wk. 3.1355 (AICuMg2), 144
Otto Fuchs AM25 (Prop.) [Aw] ... CEN 7050, 202 Hoogovens 2240, 165
AA 5052, 177 Otto Fuchs AZ86 (Prop.) [Aw] ... NF A-U4G1, 218
CEN 5052, 177 AA 7049A, 202 P-AICu4.5MgMnplacc. (I) [Aw] ...
Otto Fuchs AM30 (Prop.) [Aw] ... CEN 7049A, 202 AA 2024 Alclad, 162
AA 5754,187 Otto Fuchs E (Prop.) [Aw] ... P-AIMgO.2 (I) [Aw] ...
CEN 5754, 187 DIN Wk. 3.0305 (AI99.9), 143 AA 5005A, 174
Otto Fuchs AM32 (Prop.) [Aw] ... Otto Fuchs E05 (Prop.) [Aw] ... Alusingen 214, 150
AA 5754,187 DIN Wk. 3.3308 (AI99.9MgO.5), 146 DIN AI Mg1, 212
CEN 5754, 187 Otto Fuchs E1 (Prop.) [Aw] ... P-AIMgO.8 (I) [Aw] ...
Otto Fuchs AM36 (Prop.) [Aw] ... DIN Wk. 3.3318, 146 AA 5005,174
AA 5052,177 Otto Fuchs ES90 (Prop.) [Aw] ... Alusuisse Peraluman-100 (101), 223
CEN 5052, 177 DIN Wk. 3.3208 (AI99.9MgSi), 145 CEN 5005, 174
Otto Fuchs AM40 (Prop.) [Aw] ... DIN Wk. 3.3315 (AIMg1), 146
Otto Fuchs M10 (Prop.) [Mw] ...
AA 5083,178 Hoogovens 5010, 174
DIN Wk. 3.5003, 297
CEN 5083, 179
Otto Fuchs MA30 (Prop.) [Mw] ...
ASTM AZ31 B, 301
Alloy Cross-Reference Listing 495
P-AIMgO.9 (I) [Aw] ~ P-ALP 99.5 (I) [Aw] ~ Pech. Affimet Calypso 67XB1 (Prop)[Ae]~
AA 5005, 174 AA 1050A, 152 NF A-S7G06, 257
AA 5657,186 Alusingen 134, 149 Pech. Affimet Calypso 69B (Prop.) [Ae] ~
Alusingen 278, 150 Alusuisse Pure Aluminium 99.5, 227 NF A-S10G, 258
Alusingen 289, 150 CEN 1050A, 152 Valfond Silafont 36, 288
Alusuisse Peraluman-100 (101), 223 DIN AI 99.5, 210 Pech. Affimet Calypso 69N (Prop.) [Ae] ~
Alusuisse Peraluman-860, 225 DIN Wk. 3.0255 (AI99.5), 143 NF A-S10G, 258
Alusuisse Peraluman-863, 225 NF A-5, 210
Valfond Silafont 36, 288
CEN 5005, 174 NF A-5l, 210
CEN 5657, 186 Pech. Affimet Calypso 82P (Prop.) [Ae] ~
P-ALP 99.8 (I) [Aw] ~ NF A-S12UNG, 259
DIN AI 99.85 Mg1, 211 AA 1080A, 153
DIN Wk. 3.3315 (AIMg1), 146 Alusingen 111, 149 Pechiney CP271 (discontinued) [Aw]~
Hoogovens 5010, 174 Alusuisse Pure Aluminium 99.8, 227 AA 8090,209
P-AIMg1.5 (I) [Aw] ~ CEN 1080A, 153 Pechiney CP274 (discontinued) [Aw] ~
AA 5050, 176 DIN AI 99.8, 210 AA 2091, 163
Alusuisse Peraluman 150/151, 223 DIN Wk. 3.0285 (AI99.8), 143 Pechiney/Affimet A-Z10S8G (Prop.) [Ae] ~
CEN 5050, 176 P-AISiO.4Mg (I) [Aw] ~ Affimet A-Z1 OS8G, 261
P-AIMg2.5 (I) [Aw] ~ AA 6063,193 Pechiney/Affimet Calypso 87P (Prop)[Ae]~
AA 5052,177 CEN 6063, 193 AA A390.0, 263
Alusuisse Peraluman 253, 224 DIN AI Mg SiO.5, 212 Precedent 71A Old AA (USA) [Ae] ~
CEN 5052, 177 P-AISiO.5Mg (I) [Aw] ~ AA 771.0, 244
DIN Wk. 3.3523 (AIMg2.5), 146 AA6101,196 AA 771.2, 245
Hoogovens 5520, 185 CEN 6101,196 Precedent 71A (Prop) [Ae] ~
VAW 63/52, 148 DIN E-AI Mg SiO.5, 220 AA 771.0, 244
P-AIMg3.5 (I) [Aw] ~ P-AISi1 MgMn (I) [Aw] ~ AA 771.2, 245
AA 5754, 187 AA 6082, 194 Precedent 71 BOld AA (USA) [Ae] ~
Alusingen 234, 150 Alusuisse Anticorodal 110/112, 217 AA 772.0, 245
Alusuisse Peraluman-300 (301),224 Alusuisse Anticorodal112/114, 217 AA 772.2, 245
Alusuisse Peraluman-302, 224 Alusuisse Anticorodal-1 00/1 05, 216
CEN 5754, 187 Precedent 71B (Prop.) [Ae] ~
BOAl UKAM68, 215
DIN AI Mg3 EQ, 212 AA 772.0, 245
CEN 6082, 195
DIN Wk. 3.3535 (AIMg3), 147 AA 772.2, 245
DIN AI Mg Si1, 213
Hoogovens 5030, 175 DIN Wk. 3.2315 (AIMgSi1), 145
NF A-G3, 210 Hoogovens 6010, 189 Q
P-AIMg4.4 (I) [Aw] ~ NF A-SGMO.7, 218
AA 5083,178 P-AIZn4.5Mg (I) [Aw] ~ QE22A ASTM (USA) [Me] ~
Alusuisse Peraluman-460/462, 225 AA 7020,200 ASTM QE22A, 312
Alusuisse Peraluman-462, 225 Alusuisse Unidur 102, 229 BS MAG13, 310
CEN 5083, 179 CEN 7020, 200
Hoogovens 5510, 185 QE22A-T6 ASTM (USA) [Me] ~
DIN AI Zn4.5 Mg1, 214
Superform Metals 5083 SPF, 179 Magnesium Elektron QE22, 304
DIN Wk. 3.4335 (AIZn4.5Mg1), 147
P-AIMgSi (I) [Aw] ~ Hoogovens 7350, 206 QH21A ASTM (USA) [Me] ~
AA 6060,190 ASTM QH21A, 313
Pantal 5 (Prop) [Ae] ~
AA 6063,193 NF A-S4G, 256 QQ-A-200/2 (USA) [Aw] ~
Alunord 6060.48, 191 AA 2014, 159
Pantal 7 (Prop.) [Ae] ~
Alunord 6060.79, 191 CEN 2014, 160
AA A356.2. 262
Alusuisse Anticorodal 045/0501053, 216 QQ-A-200/3 (USA) [Aw] ~
Alusuisse Extrudal-043, 221 Pd02/35 DIN (D) [Tw] ~
AA 2024, 161
Alusuisse Extrudal-050, 221 Titanium IntI. Ti-7, 338
CEN 2024, 162
BOAl UK AM62, 214 Pech. Affimet Calypso 25M (Prop.) [Ae] ~
QQ-A-200/4 (USA) [Aw] ~
CEN 6060, 190 AA A206.2, 261
AA 5083,178
CEN 6063, 193 Pech. Affimet Calypso 43B (Prop.) [Ae] ~ CEN 5083, 179
DIN AI Mg SiO.3, 212 NF A-S13, 259
QQ-A-200/5 (USA) [Aw] ~
DIN AI Mg SiO.5, 212 Pech. Affimet Calypso 43X (Prop.) [Ac] ~ AA 5086,179
DIN AI Mg SiO.5, 212 NF A-S13, 259 CEN 5086, 180
DIN Wk. 3.3206 (AIMgSiO.5), 145
Pech. Affimet Calypso 49R (Prop.) [Ae] ~ QQ-A-200/6 (USA) [Aw] ~
NF AGS, 210
NF A-S9 Y4, 257 AA 5454, 184
P-AIMn1.2 (I) [Aw] ~
Pech. Affimet Calypso 67B (Prop.) [Ae] ~ CEN 5454, 185
AA 3103, 169
NF A-S7G03, 257 QQ-A-200/7 (USA) [Aw] ~
CEN 3103. 169
DIN AI Mn1, 213 Pech. Affimet Calypso 67B1 (Prop.) [Ae] ~ AA 5456,185
DIN Wk. 3.0315 (AIMn1), 143 NF A-S7G06, 257 CEN 5456A, 185
Hoogovens 3000, 166 Pech. Affimet Calypso 67N (Prop.) [Ae] ~ QQ-A-200/8 (USA) [Aw] ~
P-ALP 99.0 (I) [Aw] ~ NF A-S7G03, 257 AA 6061, 191
AA 1200. 156 Pech. Affimet Calypso 67N1 (Prop.) [Ae] ~ CEN 6061, 192
Alusuisse Pure Aluminium 99.0, 226 NF A-S7G06, 257 QQ-A-200/11 (USA) [Aw] ~
CEN 1200, 156 Pech. Affimet Calypso 67R (Prop.) [Ae] ~ AA 7075,203
DIN A199, 210 NF A-S7G03, 257 CEN 7075, 204
Hoogovens 1010, 151 Pech. Affimet Calypso 67R1 (Prop.) [Ae] ~ QQ-A-200/15 (USA) [Aw] ~
lawson Mardon (lM) Star 1201, 156 NF A-S7G06, 257 AA 7075,203
VAW 99/00, 149 CEN 7075, 204
Pech. Affimet Calypso 67S (Prop.) [Ae] ~
NF A-S7G03, 257
Pech. Affimet Calypso 67S2 (Prop.) [Ae] ~
NF A-S7G03. 257
Pech. Affimet Calypso 67XB (Prop.) [Ae] ~
NF A-S7G03, 257
496 Alloy Cross-Reference Listing
QQ-A-22S/4 (USA) [Aw] -+ QQ-M-31B (USA) [Mw] -+ QQ-M-S6B (USA) [Me] -+
AA 2014, 159 AECMA MG-P-63, 311 ASTM QE22A, 312
CEN 2014, 160 ASTM AZ31B, 301 ASTM ZK61A, 315
QQ-A-225/S (USA) [Aw] -+ ASTM AZ61A, 301 BS MAG1, 309
AA 2017, 160 ASTM AZ80A, 302 BS MAG13, 310
QQ-A-22S/6 (USA) [Aw] -+ BS MAG-E-121M, 308
Comeca AZ31B, 301
BS MAG6, 310
AA 2024, 161 BS MAG9, 310
CEN 2024, 162 DIN 3.5612, 297 Magnesium Elektron EZ33, 304
Magnesium Elecktron AZ61, 301 Magnesium Elektron QE22, 304
QQ-A-22S/8 (USA) [Aw] -+ Magnesium Elektron AZ31, 300
AA 6061,191 NF G-A6Z1, 306
CEN 6061, 192 R
QQ-A-22S/9 (USA) [Aw] -+ QQ-M-38 (USA) [Me] -+
ASTM AZ91A, 303
AA 7075,203
QQ-M-40 (USA) [Mw] -+ R (Prop.) [Aw] -+
CEN 7075, 204 DIN Wk. 3.0400, 144
ASTM AZ31 B, 301
QQ-A-2S0/3 (USA) [Aw] -+ ASTM HM21A, 307 ROS (Prop.) [Aw] -+
AA 2014 Alclad, 160 ASTM ZK60A, 315 DIN Wk. 3.3309, 146
QQ-A-2S0/4 (USA) [Aw] -+ BS MAG-x-161, 309 R1 (Prop) [Aw] -+
AA 2024, 161 Comeca AZ31B, 301 DIN Wk. 3.3319, 146
CEN 2024, 162 DIN Wk. 35161,297 RS02S0 UNS (USA) [Tw] -+
QQ-A-2S0/S (USA) [Aw] -+ Magnesium Elektron AZ31, 300 ASTM Grade 1, 332
AA 2024 Alclad, 162 NF G-Z5Zr, 306 Teledyne Allvac 30, 329
QQ-A-2S0/6 (USA) [Aw] -+ QQ-M-40B (USA) [Mw] -+ RS0400 UNS (USA) [Te] -+
AA 5083, 178 AECMA MG-P-63, 311 NF T 40,336
CEN 5083, 179 ASTM AZ61A, 301
RS0400 UNS (USA) [Tew] -+
QQ-A-2S0/7 (USA) [Aw] -+ ASTM AZ80A, 302
Timetal 50A, 323
AA 5086, 179 BS 2L 121, 297
BS MAG-E-121M, 308 RS0400 UNS (USA) [Tw] -+
CEN 5086, 180 ASTM Grade 2, 332
CEN MG-P-61, 311
QQ-A-2S0/8 (USA) [Aw] -+ DIN 3.5612, 297 CEN Ti P99002, 341
AA 5052, 177 Deutsche Titan Tikrutan RT 15, 343
DIN 3.5812, 297
CEN 5052, 177 Teledyne Allvac 40, 329
Magnesium Elecktron AZ61, 301
QQ-A-2S0/9 (USA) [Aw] -+ Magnesium Elektron AZ80, 302 RSOSOO UNS (USA) [Tew] -+
AA 5456, 185 NF G-A6Z1, 306 Timetal 65A, 323
CEN 5456A, 185 NF G-A7Z1, 306 RSOSOO UNS (USA) [Tw] -+
QQ-A-2S0/10 (USA) [Aw] -+ NF G-A8Z, 306 ASTM Grade 3, 332
AA 5454, 184 QQ-M-44B (USA) [Mw] -+ Deutsche Titan Tikrutan RT 18, 343
CEN 5454, 185 ASTM AZ31B, 301 DIN Wk. 3.7055, 318
QQ-A-2S0/11 (USA) [Aw] -+ Comeca AZ31 B, 301 RSOSSO UNS (USA) [Tw] -+
AA 6061, 191 Magnesium Elektron AZ31, 300 Teledyne Allvac 55, 329
CEN 6061, 192 QQ-M-S4 (USA) [Mw] -+ RS0700 UNS (USA) [Tw] -+
QQ-A-2S0/12 (USA) [Aw] -+ ASTM MIA, 312 ASTM Grade 4, 332
AA 7075,203 QQ-M-SS (USA) [Me] -+ CEN Ti P99003, 341
CEN 7075, 204 ASTM AM100A, 298 Deutsche Titan Tikrutan RT 20, 343
QQ-A-2S0/13 (USA) [Aw] -+ ASTM AZ63A, 302 DIN Wk. 3.7065, 318
AA 7075 Alclad, 204 ASTM AZ81 A, 302 Teledyne Allvac 70, 329
QQ-A-2S0/24 (USA) [Aw] -+ ASTM AZ92A, 304 Timetal 75A, 323
AA 7075,203 ASTM EZ33A, 306 RS22S0 UNS (USA) [Tw] -+
CEN 7075, 204 ASTM QE22A, 312 ASTM Grade 11, 333
QQ-A-2S0/2S (USA) [Aw] -+ QQ-M-SS (USA) [Mew] -+ RS2400 UNS (USA) [Tw] -+
AA 7075 Alclad, 204 ASTM HK31A, 307 ASTM Grade 7,333
QQ-A-2S0/29 (USA) [Aw] -+ QQ-M-SS; MS6 (USA) [Me] -+ RS4260 UNS (USA) [Tw] -+
AA 2124,164 ASTM AZ91C, 303 AMS 4919,327
CEN 2124, 164 RIMA AZ91C, 303 R54S20 UNS (USA) [Tew] -+
QQ-A-2S0/30 (USA) [Aw] -+ QQ-M-S6 (USA) [Me] -+ 3620-TA7, 326
AA 2219, 165 ASTM AZ63A, 302 AMS 4910,327
CEN 2219, 165 ASTM AZ81A, 302 AMS 4926, 328
QQ-A-367 (USA) [Aw] -+ ASTM AZ91C, 303
ASTM AZ92A, 304
ASTM Grade 6,333
DIN Wk. 3.7115, 318
AA 2014, 159
AA2618,165 ASTM EZ33A, 306 DTD 5083, 328
AA6061,191 ASTM HZ32A, 307 NF TA 5E, 336
AA 7049,202 ASTM ZH62A, 314 RS4S21 UNS (USA) [Tw] -+
AA 7075,203 RIMA AZ91C, 303 AMS 4909, 327
CEN 2014, 160 QQ-M-S6 (USA) [Mew] -+ AMS 4924, 327
CEN 6061, 192 ASTM HK31A, 307 VT51,344
CEN 7075, 204 QQ-M-S6A (USA) [Me] -+ RS4620 UNS (USA) [Tw] -+
QQ-M-31 (USA) [Mw] -+ ASTM ZK51A, 314 DIN LW 3.7144,319
ASTM MIA, 312 BS MAG4, 310 Teledyne Allvac 6-2-4-2, 328
ASTM ZK60A, 315 BS MAG8, 310 Timetal 6-2-4-2, 321
BS MAG-x-161, 309 RS4790 UNS (USA) [Tw] -+
Comeca AZ31B, 301 AMS 4974, 328
DIN Wk. 3.5161, 297 BS TA18, 337
Magnesium Elektron AZ31, 300 BS TA20, 337
NF G-Z5Zr, 306 UNS R54790, 334
Alloy Cross-Reference Listing 497
R5481 0 UNS (USA) [Tw] -+ RIMA AZ91C (Prop) [Me]-+ Siluman-Kappa (Prop) [Ae] -+
AMS 4915, 327 ASTM AZ91 C, 303 AA 369.1, 240
MIL R-81588, 334 RIMA AZ91 C, 303 Silumin (Prop.) [Ae] -+
Teledyne Allvac 8-1-1, 329 RIMA AZ91 HP (Prop.) [Me] -+ AA A413.2, 263
Timetal 8-1-1, 322 RIMA AZ91 HP, 303 BS LM6, 285
R56080 UNS (USA) [Tw] -+ RR58 (Prop.) [Aw] -+ Silumin-Beta (Prop.) [Ae] -+
UNS R56080, 334 AA 2618A, 166 AA 359.2, 239
R56260 UNS (USA) [Tw] -+ CEN 2618A, 166 Special K-9 (Prop.) [Ae] -+
IM1646,325 RT 12 - Tikrutan (Prop.) [Tw]-+ AA 369.0, 240
Teledyne Allvac 6-2-4-6, 329 DIN Wk. 3.7025, 318 AA 369.1, 240
Timetal 6-2-4-6, 321 RT 12 Pd - Tikrutan (Prop.) [Tw] -+ Special K-9 Old AA (USA) [Ae] -+
UNS R56260, 334 AA 369.0, 240
DIN Wk. 3.7225, 320
R56320 UNS (USA) [Tw] -+ RT 15 - Tikrutan (Prop.) [Tw] -+ AA 369.1, 240
ASTM 3AI-2.5V, 321 Superform 5083 SPF (Prop.) [Aw] -+
DIN Wk. 3.7035, 318
ASTM Grade 9, 333
TimetaI3-2.5,318
RT 15 Pd - Tikrutan (Prop.) [Tw] -+ AA 5083,178
DIN Wk. 3.7235, 321 Superform Metals 5083 SPF, 179
R56400 UNS (USA) [Tcw]-+ Supral100 (Prop.) [Aw]-+
RT 18 - Tikrutan (Prop.) [Tw]-+
NF TA6V. 336 AA 2004, 158
Timetal 6-4, 321 DIN Wk. 3.7055, 318
Superform Metals Supral 100, 228
R56400 UNS (USA) [Tw] -+ RT 18 Pd - Tikrutan (Prop.) [Tw] -+
DIN Wk. 3.7255, 321 Supral150 (Prop.) [Aw]-+
AMS 4905, 326 Superform Metals Supral 150, 228
ASTM Grade 5,333 RT 20 - Tikrutan (Prop.) [Tw] -+
BS 2TA10, 317 DIN Wk. 3.7065, 318
CEN Ti P63, 340 RZ5 (Prop.) [Me] -+ T
Deutsche Titan Tikrutan LT 31, 342 AECMA MG-C-43, 311
DIN LW 3.7164, 319 ASTM ZE41A, 314 T2 - Otto Fuchs (Prop.) [Tw] -+
DIN Ti AI6 V4, 339 BS MAG5, 310 DIN Wk. 3.7025, 318
DIN Wk. 3.7165, 320 DIN Wk. 3.5101,297
DTD 5163,328 Magnesium Elektron ZE41, 305
T3 - Otto Fuchs (Prop.) [Tw] -+
NF Ti P64001, 340 DIN Wk. 3.7035, 318
NF G-Z4TR, 306
Teledyne Allvac 6-4, 329 RZ5 NF (F) [Me] -+
T6 - Otto Fuchs (Prop.) [Tw] -+
R56401 UNS (USA) [Tw] -+ DIN Wk. 3.7065, 318
AECMA MG-C-43, 311
AMS 4907, 327 ASTM ZE41A, 314 T 30 NF (F) [Tw] -+
ASTM Grade 23, 334 BS MAG5, 310 ASTM Grade 1, 332
NF TA6V ELI, 336 DIN Wk. 3.5101, 297 T 35 NF (F) [Tw] -+
Teledyne Allvac 6-4 ELI, 329 Magnesium Elektron ZE41, 305 BS 2TA1, 317
R56620 UNS (USA) [Tw] -+ NF G-Z4TR, 306 CEN Ti P99001, 341
AMS 4918, 327 Deutsche Titan Tikrutan RT 12,342
DIN Wk. 3.7025, 318
Deutsche Titan Tikrutan LT 33, 342
DIN LW 3.7174,320 s Timetal 35A, 322
DIN Wk. 3.7175, 320 T 40 NF (F) [Te] -+
Teledyne Allvac 6-6-2, 329 55 CSA (Can) [Aw] -+ NF T 40,336
AA 4043, 172
Timetal 6-6-2, 321 T 40 NF (F) [Tew] -+
R56700 UNS (USA) [Tw] -+ AA 4543,173
Timetal 50A, 323
Teledyne Allvac 6-7, 329 512 CSA (Can) [Aw]-+
T 40 NF (F) [Tw] -+
R56740 UNS (USA) [Tw] -+ AA4047,173
ASTM Grade 2, 332
UNS R56740, 334 SAE 329 Old AA (USA) [Ae] -+ CEN Ti P99002, 341
R58010 UNS (USA) [Tw] -+ AA B319.0, 276 Deutsche Titan Tikrutan RT 15, 343
Ti-13V-11 Cr-3AI, 339 SAP A 6063 HIP (Prop.) [Aw] -+ DIN Wk. 3.7035, 318
AMS 4917,327 AA 6063, 193 T 50 NF (F) [Tew] -+
Crucible Steel Co. B 120 VCA, 330 SAP A 6063 HIS (Prop.) [Aw] -+ Timetal 65A, 323
R58640 UNS (USA) [Tew] -+ AA 6063, 193 ASTM Grade 3, 332
Beta C, 330 5APA 6063 HIT (Prop.) [Aw] -+ Deutsche Titan Tikrutan RT 18, 343
UNS R58640, 335 AA 6063, 193 DIN Wk. 3.7055, 318
R58820 UNS (USA) [Tw] -+ SBS1050 (ZA) [Aw]-+ T 60 NF (F) [Tew] -+
TI-8Mo-8V-2Fe-3AI, 338 AA1050,151 ASTM Grade 4,333
UNS R58820, 335 Hoogovens 1000,151 Timetal 100A, 323
Reynolds 2010 (Prop.) [Aw]-+ VAW 99/52, 149 T 60 NF (F) [Tw] -+
AA 2010, 158 SECO Dilute (Prop.) [Aw] -+ ASTM Grade 4, 332
CEN Ti P99003, 341
Reynolds 2036 (Prop.) [Aw] -+ AA 6060,190
Deutsche Titan Tikrutan RT 20, 343
AA 2036, 163 Alunord 6060.48, 191
Alunord 6060.79, 191 DIN Wk. 3.7065, 318
Reynolds 6111 (modified) (Prop) [Aw] -+ Timetal 75A, 323
AA6111,196 SEL 1000 (UK) [Aw] -+
AA 6063A, 193 TA 1 (UK) [Tw] -+
Reynolds 7021 (Prop.) [Aw] -+ ASTM Grade 1, 332
AA 7021,200 SG11P CSA (Can) [Aw]-+
Deutsche Titan Tikrutan RT 12, 342
Reynolds 7029 (Prop.) [Aw] -+ AA6151,197
DIN Wk. 3.7025, 318
AA 7029,201 SG121 CSA (Can) [Aw] -+ Titanium Industries GR-1, 331
Reynolds R-2000 (tooling plate) (Prop.) AA 4032, 172
TA 2 (UK) [Tew]-+
[Aw]-+ SG-AISi9Cu (I) [Ae] -+ DIN Wk. 3.7035, 318
AA 6061, 191 UNI 7369-74 Part 3,249 Titanium Industries GR-2, 331
Reynolds Tread-Brite (Prop.) [Aw] -+ SG-AISi9Cu1 (I) [Ae] -+ TA 3 (UK) [Tew]-+
AA 3003,166 CEN 46400, 253 DIN Wk. 3.7035, 318
Reynolds Weldalite 049 (Prop.) [Aw] -+ Siluman-Delta (Prop.) [Ae] -+ Titanium Industries GR-2, 331
AA 2095,163 AA 409.2, 241
498 Alloy Cross-Reference Listing
Tikrutan RT 15 Pd (Prop.) [Tw] ~ Timetal100A (Prop.) [Tew] ~ Ti P01 CEN (EUR) [Tw] ~
DIN Wk. 3.7235, 321 ASTM Grade 4, 333 DIN Wk. 3.7025, 318
Tikrutan RT 18 (Prop.) [Tw] ~ Timetal 100A, 323 Ti P01 (UK) [Tw] ~
DIN Wk. 3.7055, 318 Timetal 230 (Prop.) [Tw] ~ BS 2TA1, 317
Tikrutan RT 18 Pd (Prop.) [Tw] ~ AECMA Ti P9001 , 340 CEN Ti P99001, 341
DIN Wk. 3.7255, 321 BS 2TA21 , 317 Timetal 35A, 322
Tikrutan RT 20 (Prop.) [Tw] ~ Deutsche Titan Tikrutan LT 25, 341 Ti P02 AECMA (EUR) [Te] ~
DIN Wk. 3.7065, 318 DIN LW 3.7124,319 NF T 40,336
NF T-U2, 344
Timetal 3-2,5 (Prop.) [Tw] ~ Ti P02 AECMA (EUR) [Tew] ~
Timetal 230, 324
Ti-3AI-2.5V, 337 Timetal 50A, 323
ASTM 3AI-2.5V, 321 Timetal 367 (Prop.) [Tw] ~
Ti P02 AECMA (EUR) [Tw] ~
ASTM Grade 9,333 IMI 367, 324
ASTM Grade 2, 332
TimetaI3-2.5,318 Timetal 367, 324
CEN Ti P99002, 341
Timetal 6-2-4-2 (Prop.) [Tw] ~ Timetal 550 (Prop.) [Tw] ~ Deutsche Titan Tikrutan RT 15, 343
Ti-6242, 339 BS TA45, 337 DIN Wk. 3.7035, 318
TimetaI6-2-4-2, 321 Deutsche Titan Tikrutan LT 34, 342
Ti P02 CEN (EUR) [Tw] ~
TimetaI6-2-4-2, 321 DIN LW 3.7184,320
DIN Wk. 3.7035, 318
IM1646,325 DIN Wk. 3.7185, 320
NF TA 4DE, 336 Ti P04 AECMA (EUR) [Tw] ~
TimetaI6-2-4-6, 321 ASTM Grade 4, 332
UNS R56260, 334 Timetal 550, 324
CEN Ti P99003, 341
Timetal 6-4 (Prop.) [Tew] ~ Timetal 551 (Prop) [Tw] ~
Deutsche Titan Tikrutan RT 20, 343
NF TA6V, 336 IMI 551, 324
DIN Wk. 3.7065, 318
Timetal 6-4, 321 Timetal 551, 325
Timetal 75A, 323
Timetal 6-4 (Prop.) [Tw] ~ Timetal 679 (Prop.) [Tw] ~
Ti P11 AECMA (EUR) [Tw] ~
AMS 4905,326 Timetal 679, 325
AECMA Ti P9001, 340
ASTM Grade 5,333 Timetal 685 (Prop.) [Tw] ~ BS 2TA21, 317
BS 2TA10, 317 Deutsche Titan Tikrutan LT 26, 341 Deutsche Titan Tikrutan LT 25, 341
CEN Ti P63, 340 DIN Wk. 3.7155, 319 NF T-U2, 344
DIN LW 3.7164, 319 IM1685,325 Timetal 230, 324
DIN Ti AI6 V4, 339 NF T-A6Zr5D, 337
Ti P11 CEN (EUR) [Tw] ~
DIN Wk. 3.7165, 320 Timetal 685, 325
AECMA Ti P9001, 340
DTD 5163,328 Timetal 829 (Prop.) [Tw] ~ BS 2TA21, 317
NF Ti P64001 , 340 IM1829,326 Deutsche Titan Tikrutan LT 25, 341
Timetal 6-6-2 (Prop.) [Tw] ~ Timetal 829, 326 DIN LW 3.7124,319
AMS 4918, 327 IM1834,326 NF T-U2, 344
Deutsche Titan Tikrutan LT 33, 342 Timetal 834, 326 Timetal 230, 324
DIN LW 3.7174,320 Timetal Code 12 (Prop.) [Tew] ~ Ti P62 AECMA (EUR) [Tw] ~
DIN Wk. 3.7175, 320 ASTM Grade 12, 334 AECMA Ti P62, 340
Timetal 6-6-2, 321 Deutsche Titan Tikrutan LT 27, 342 ASTM 17,321
Timetal 8-1-1 (Prop.) [Tw] ~ DIN Wk. 3.7105, 318 ASTM F7, 331
Ti-8AI-1 Mo-1V, 338 Timetal Code 12, 331 Crucible Steel Co. C 130AM, 330
MIL R-81588, 334 Timminco AM605X (Prop.) [Me] ~ DTD 5053, 328
TimetaI8-1-1,322 ASTM AM60, 299 IMI 314A, 324
TimetaI10-2-3 (Prop.) [Tw] ~ ASTM AM60B, 299 NF TA 5M, 336
Timetal 10-2-3, 322 Timminco AM60SX, 299 Ti-P63 AECMA (EUR) [Tew] ~
Timetal 15-3 (Prop.) [Tw] ~ Timminco AM60X (Prop.) [Me] ~ NF TA6V, 336
Ti-15-3, 339 ASTM AM60, 299 Timetal 6-4, 321
Timetal 15-3, 322 ASTM AM60B, 299 Ti-P63 AECMA (EUR) [Tw] ~
Timminco AM60X, 299 AMS 4905, 326
Timetal 215 (Prop.) [Tw] ~
Timetal21S, 322 Timminco AZ63 (Prop.) [Mc] ~ ASTM Grade 5, 333
ASTM AZ63A, 302 BS 2TA10, 317
Timetal 35A (Prop.) [Tw] ~
Timminco AZ63, 302 CEN Ti P63, 340
BS 2TA1, 317
Timminco AZ91UX (Prop.) [Me] ~ Deutsche Titan Tikrutan LT 31, 342
CEN Ti P99001, 341
ASTM AZ91 D, 303 DIN LW 3.7164, 319
Timetal 35A, 322
ASTM AZ91 D, 303 DIN Ti AI6 V4, 339
Timetal 50A (Prop.) [Tew] ~ DIN Wk. 3.7165, 320
ASTM AZ91 E, 303
Timetal 50A, 323 DTD 5163,328
CEN Ti P99002, 341 Timminco AZ91 UX, 304
NF Ti P64001, 340
Deutsche Titan Tikrutan RT 15, 343 Timminco AZ91X (Prop.) [Me] ~
ASTM AZ91 D, 303 Ti P63 CEN (EUR) [Tew] ~
Timetal50A (Prop.) [Tw] ~ NFTA6V, 336
ASTM AZ91 E, 303
ASTM Grade 2, 332 TimetaI6-4, 321
RIMA AZ91 HP, 303
NF T 40,336
Timminco AZ91 X, 304 Ti P63 CEN (EUR) [Tw] ~
Timetal 65A (Prop.) [Tew] ~ AMS 4905, 326
Timminco AZ92 (Prop.) [Me] ~
Timetal 65A, 323 ASTM Grade 5, 333
ASTM AZ92A, 304
Timetal65A (Prop.) [Tw] ~ Timminco AZ92, 304 BS 2TA10, 317
ASTM Grade 3, 332 CEN Ti P63, 340
Deutsche Titan Tikrutan RT 18, 343 TiNiMo083 DIN (D) [Tew] ~
Deutsche Titan Tikrutan LT 31, 342
DIN Wk. 3.7055, 318 Deutsche Titan Tikrutan LT 27, 342
DIN LW 3.7164, 319
DIN Wk. 3.7105, 318
Timetal 75A (Prop.) [Tw] ~ DIN Ti AI6 V4, 339
Ti P01 AECMA (EUR) [Tw] ~ DIN Wk. 3.7165, 320
ASTM Grade 4, 332
CEN Ti P99003, 341 BS 2TA1, 317 DTD 5163,328
CEN Ti P99001, 341 NF Ti P64001 , 340
Deutsche Titan Tikrutan RT 20, 343
Deutsche Titan Tikrutan RT 12, 342
DIN Wk. 3.7065, 318
Timetal 75A, 323 DIN Wk. 3.7025, 318
Timetal 35A, 322
Alloy Cross-Reference Listing 501
Ti P64 AECMA (EUR) [Tw] -+ Ti P64001 AECMA (EUR) [Tew] -+ Titanium Industries 15-3 (Prop) [Tw] -+
AMS 4918, 327 NF TA6V, 336 Timetal 15-3, 322
Deutsche Titan Tikrutan LT 33, 342 TimetaI6-4, 321 Titanium Industries 550 (Prop.) [Tw] -+
DIN LW 3.7174,320 Ti P64001 AECMA (EUR) [Tw] -+ Timetal 550, 324
DIN Wk. 3.7175, 320 AMS 4905, 326 Titanium Industries GR-1 (Prop.) [Tw] -+
Timetal 6-6-2, 321 ASTM Grade 5, 333 ASTM Grade 1, 332
Ti P64 CEN (EUR) [Tw] -+ BS 2TA10, 317 Titanium Industries GR-2 (Prop.) [Tw] -+
AMS 4918,327 CEN Ti P63, 340 ASTM Grade 2, 332
Deutsche Titan Tikrutan LT 33, 342 Deutsche Titan Tikrutan LT 31, 342
DIN LW 3.7164, 319 Titanium Industries GR-3 (Prop.) [Tw] -+
DIN LW 3.7174,320
DIN Ti AI6 V4, 339 ASTM Grade 3, 332
DIN Wk. 3.7175, 320
Timetal 6-6-2, 321 DIN Wk. 3.7165, 320 Titanium Industries GR-4 (Prop.) [Tew] -+
ASTM Grade 4, 333
Ti P65 AECMA (EUR) [Tew] -+ DTD 5163,328
3620-TA7, 326 NF Ti P64001, 340 Titanium Industries GR-5 (Prop.) [Tw] -+
Ti P65 AECMA (EUR) [Tw] -+ Ti P64001 NF (F) [Tew] -+ ASTM Grade 5, 333
AMS 4910, 327 NF TA6V, 336 Titanium Industries GR-7 (Prop.) [Tw] -+
AMS 4926, 328 Timetal 6-4, 321 ASTM Grade 7, 333
ASTM Grade 6, 333 Ti P64001 NF (F) [Tw] -+ ASTM Grade 11, 333
DIN Wk. 3.7115, 318 AMS 4905, 326 Titanium Industries GR-12 (Prop.) [Tew] -+
DTD 5083, 328 ASTM Grade 5, 333 ASTM Grade 12, 334
NF TA 5E, 336 BS 2TA10, 317 TL35 - Otto Fuchs (Prop.) [Tw] -+
Ti P66 AECMA (EUR) [Tw] -+ CEN Ti P63, 340 DIN Wk. 3.7110, 318
Deutsche Titan Tikrutan LT 31, 342
AMS 4915, 327 TL44 (Prop.) [Tw] -+
MIL R-81588, 334 DIN LW 3.7164, 319
DIN LW 3.7184,320
Timetal 8-1-1, 322 DIN Ti AI6 V4, 339
DIN Wk. 37185, 320
DIN Wk. 3.7165, 320
Ti P67 AECMA (EUR) [Tw] -+ TL62 (Prop.) [Tw] -+
DTD 5163,328
Deutsche Titan Tikrutan LT 26, 341 AMS 4919,327
NF Ti P64001, 340
DIN Wk. 3.7155, 319 DIN LW 3.7144, 319
IM1685,325 Ti P99001 (UK) [Tw] -+
UNS R56260, 334
BS2TA1,317
NF T-A6Zr5D, 337
CEN Ti P99001, 341 TL64 - Otto Fuchs (Prop) [Tw] -+
Timetal 685, 325 DIN Wk. 3.7165, 320
Timetal 35A, 322
Ti P67 CEN (EUR) [Tw] -+
Ti P99001 AECMA (EUR) [Tw]-+ TL66 (Prop.) [Tw] -+
Deutsche Titan Tikrutan LT 26, 341 DIN LW 3.7174,320
DIN Wk. 3.7155, 319 BS2TA1,317
IM1685,325 CEN Ti P99001, 341 T-U2 NF (F) [Tw] -+
NF T-A6Zr5D, 337 DIN Wk. 3.7025, 318 AECMA Ti P9001, 340
Timetal 685, 325 Timetal 35A, 322 BS 2TA21 , 317
Ti P68 AECMA (EUR) [Tw] -+ Ti P99001 CEN (EUR) [Tw] -+ Deutsche Titan Tikrutan LT 25, 341
BS 2TA1, 317 DIN LW 3.7124,319
BS TA45, 337
CEN Ti P99001, 341 NF T-U2, 344
Deutsche Titan Tikrutan LT 34, 342
Timetal 35A, 322 Timetal 230, 324
DIN LW 3.7184, 320
DIN Wk. 3.7185, 320 Ti P99002 AECMA (EUR) [Te] -+ TZ6 NF (F) [Me] -+
NF TA 4DE, 336 NF T 40,336 ASTM ZH62A, 314
BS MAG9, 310
Timetal 550, 324 Ti P99002 AECMA (EUR) [Tew] -+
Ti P68 CEN (EUR) [Tw] -+ Timetal 50A, 323 TZ6 - Mag.Elek (Prop.) [Me] -+
BS TA45, 337 ASTM Grade 2, 332 ASTM ZH62A, 314
Deutsche Titan Tikrutan LT 34, 342 CEN Ti P99002, 341 BS MAG9, 310
DIN LW 3.7184, 320 Deutsche Titan Tikrutan RT 15, 343
DIN Wk. 3.7185, 320 Ti P99002 CEN (EUR) [Te] -+ u
Ti P68 CEN (EUR) [Tw] -+ NF T 40,336
NF TA 4DE, 336 Ti P99002 CEN (EUR) [Tew] -+ Unavia 816,02 [Me]-+
Timetal 550, 324 Timetal 50A, 323 AECMA MG-C-43, 311
Ti P69 AECMA (EUR) [Tw] -+ Ti P99002 CEN (EUR) [Tw] -+ ASTM ZE41A, 314
ASTM 3AI-2.5V, 321 ASTM Grade 2, 332 BS MAG5, 310
ASTM Grade 9, 333 CEN Ti P99002, 341 DIN Wk. 3.5101, 297
TimetaI3-2.5,318 Deutsche Titan Tikrutan RT 15, 343 NF G-Z4TR, 306
Ti P69 CEN (EUR) [Tw] -+ Ti P99003 AECMA (EUR) [Tw] -+ Magnesium Elektron ZE41, 305
ASTM 3AI-2.5V, 321 ASTM Grade 4, 332 UNI 7790 (I) [Aw] -+
ASTM Grade 9, 333 CEN Ti P99003, 341 AA 5083, 178
TimetaI3-2.5,318 Deutsche Titan Tikrutan RT 20, 343 Alusuisse Peraluman-460/462, 225
Ti P609 AECMA (EUR) [Tw] -+ DIN Wk. 3.7065, 318 Alusuisse Peraluman-462, 225
ASTM 3AI-2.5V, 321 Timetal 75A, 323 CEN 5083, 179
ASTM Grade 9, 333 Ti P99003 CEN (EUR) [Tw] -+ Hoogovens5510, 185
Timetal 3-2.5, 318 ASTM Grade 4, 332 Superform Metals 5083 SPF, 179
Ti P610 AECMA (EUR) [Tw]-+ CEN Ti P99003, 341 Unifont NF (F) [Ae] -+
TimetaI6-2-4-2, 321 Deutsche Titan Tikrutan RT 20, 343 NF Unifont, 289
TimetaI6-2-4-2, 321 DIN Wk. 3.7065, 318 USA 000: Be38AI Lockalloy [Bw] -+
Ti P9001 AECMA (EUR) [Tw] -+ Timetal 75A, 323 Brush Wellman AlbeMet AM162 Extruded
AECMA Ti P9001, 340 Titanium Industries 6-2-4-2 (Prop.) [Tw] -+ Bar, 345
BS 2TA21 , 317 Timetal 6-2-4-2, 321 Brush Wellman AlbeMet AM162 Rolled
Deutsche Titan Tikrutan LT 25, 341 Titanium Industries 6-2-4-6 (Prop.) [Tw] -+ Sheet, 345
DIN LW 3.7124,319 Timetal 6-2-4-6, 321 USA MAM4427 [Mew] -+
NF T-U2, 344 Titanium Industries 10-2-3 (Prop.) [Tw] -+ ASTM WE43A, 313
Timetal 230, 324 Timetal 10-2-3, 322
502 Alloy Cross-Reference Listing
USA-WW-T-700/3 [Aw] -+ VAW 98/50 (Prop.) [Aw] -+ VAW Veral Si12CuNiMg(H) (Prop.) [Ac] -+
AA 2024,161 AA 8011,207 AA 336.2, 238
Alusuisse Avional 150, 219 AA 8011A, 207 VAW Veral Si17Cu4Mg(H) (Prop.) [Ac] -+
Alusuisse Avional 152, 219 CEN 8011A, 208 AA A390.1, 263
CEN 2024, 162 VAW 98/50, 149
VAW Veral Si18CuNiMg(H) (Prop.) [Ac] -+
DIN Wk. 3.1355 (AICuMg2), 144 VAW 99/00 (Prop) [Aw] -+ AA 393.2, 241
Hoogovens 2240, 165 AA 1200, 156
NF A-U4G1, 218 VOS 225 DIN (D) [Ac] -+
CEN 1200, 156
CEN 45000, 252
USA-WW-T-700/6 [Aw] -+ VAW 99/00, 149
VOS 226 DIN (D) [Ac]-+
AA6061,191 VAW 99/01 (Prop.) [Aw] -+
Alusuisse Anticorodal 080, 216 CEN 46200, 253
AA 1200, 156
Alusuisse Anticorodal-082, 216 AA 8079,209 VOS 226/3 DIN (D) [Ac] -+
CEN 6061, 192 CEN 8079, 209 CEN 46500, 253
DIN Wk. 3.3211 (AIMg1 SiCu), 145 VAW 99/01, 149 VOS 2260 DIN (D) [Ac] -+
Hoogovens 6560, 198
VAW 99/52 (Prop.) [Aw] -+ CEN 46000, 252
Reynolds R-2000, 227
AA 1050, 151 VOS 230 DIN (D) [Ac] -+
USA WW-T-825 [Mw]-+ AA 1050A, 152 CEN 44100, 251
ASTM AZ31B, 301 CEN 1050A, 152 CEN 44200, 251
ASTM AZ80A, 302 VAW 99/52, 149 VOS 2300 DIN (D) [Ac] -+
ASTM MIA, 312
VAW Pantal 5 (Prop.) [Ac] -+ CEN 44300. 252
ASTM ZK60A, 315
BS MAG-x-161, 309
NF A-S4G, 256 VOS 231 DIN (D) [Ac] -+
Comeca AZ31B, 301 VAW Pantal 7 (Prop.) [Ac] -+ CEN 47000. 253
DIN Wk. 3.5161, 297 AA A356.2, 262 VOS 2310 DIN (D) [Ac] -+
Magnesium Elektron AZ31, 300 VAW Siluman-Oelta (Prop.) [Ac]-+ CEN 47100.253
NF G-Z5Zr, 306 AA 409.2, 241 VOS 233 DIN (D) [Ac] -+
USA WW-T-825B [Mw] -+ VAW Siluman-Kappa (Prop.) [Ac] -+ CEN 43200, 251
AECMA MG-P-63, 311 AA 369.1, 240 VOS 239 DIN (D) [Ac] -+
ASTM AZ61A, 301 VAW Silumin (Prop.) [Ac]-+ CEN 43000. 251
BS MAG-E-121M, 308 AAA413.2,263 CEN 43100. 251
DIN 3.5612,297 BS LM6, 285 VOS 2390 DIN (D) [Ac] -+
NF G-A6Z1, 306 VAW Silumin-Beta (Prop.) [Ac] -+ CEN 43400, 251
AA 359.2, 239 VOS 242 DIN (D) [Ac] -+
v VAW Veral 99.5 (Prop.) [Ac]-+
AA 150.1, 233
CEN 51000, 254
CEN 51100, 254
Valfond Silafont 36 (Prop.) [Ac] -+ VAW Veral 99.7 (Prop.) [Ac] -+ VOS 244 DIN (D) [Ac] -+
NF A-S10G, 258 AA 170.1, 233 CEN 51300,254
Valfond Silafont 36, 288 VAW Veral 225 (Prop.) [Ac] -+ VOS 245 DIN (D) [Ac] -+
Vanasil (Prop.) [Ac] -+ AAA319.1,262 CEN 51400, 254
AA 393.0, 241 VAW Veral 226(0) (Prop.) [Ac] -+ VOS 260 DIN (D) [Ac] -+
AA393.1,241 AA B380.1, 276 CEN 48000, 254
AA 393.2, 241 VAW Veral 226A (Prop.) [Ac] -+ VOS 349 DIN (0) [Ac] -+
Vanasil Old AA (USA) [Ac] -+ AA 333.1, 238 CEN 51200,254
AA 393.0, 241 VAW Veral 231(0) (Prop.) [Ac] -+ Veral 99.5 (Prop.) [Ac] -+
AA 393.1, 241 AAA413.1,263 AA150.1,233
AA 393.2,241
VAW Veral 233 (Prop.) [Ac] -+ Veral 99.7 (Prop.) [Ac] -+
VAW 41/20 (Prop.) [Aw] -+ AA 361 .1, 239 AA 170.1, 233
AA 3003,166
VAW Veral 241 (Prop.) [Ac] -+ Veral 225 (Prop.) [Ac] -+
CEN 3003, 167 AAA319.1,262
AA 511 1, 242
VAW 41120, 148
VAW Veral Cu4TiMg (Prop.) [Ac] -+ Veral 226(0) (Prop.) [Ac] -+
VAW 61/03 (Prop.) [Aw] -+ AA B380.1, 276
AA 204.2, 234
AA 3004,167
VAW Veral Mg3 (Prop.) [Ac]-+ Veral 226A (Prop.) [Ac] -+
CEN 3004, 167
AA 514.2, 243 AA 333.1 , 238
VAW 61/03, 148
VAW Veral Mg3(H) (Prop.) [Ac] -+ Veral 231(0) (Prop.) [Ac] -+
VAW 61/10 (Prop.) [Aw] -+
AA 514.2, 243 AAA413.1,263
AA 3105, 170
CEN 3105,170 VAW VeraIMg5(H) (Prop.) [Ac]-+ Veral 233 (Prop.) [Ac] -+
VAW61110,148 AA 535.2, 243 AA 361.1,239
VAW 61/15 (Prop.) [Aw] -+ VAW Veral Mg9 (Prop.) [Ac] -+ Veral 241 (Prop.) [Ac] -+
AA 3005,168 AA518.1,243 AA511.1,242
CEN 3005, 168 VAW Veral Mg9(H) (Prop.) [Ac] -+ Veral Mg3 (Prop.) [Ac] -+
VAW61/15,148 AA 518.2, 243 AA 514.2,243
VAW 63/37 (Prop.) [Aw] -+ VAW Veral Mg10(H) (Prop.) [Ac] -+ Veral Mg3(H) (Prop) [Ac] -+
AA 5042,176 AA 520.2, 243 AA 514.2, 243
VAW 63/37, 148 VAW Veral MgSi3(H) (Prop.) [Ac] -+ Veral Mg9 (Prop.) [Ac] -+
VAW 63/45 (Prop.) [Aw] -+ AA 512.2,242 AA518.1, 243
AA 5182, 181 VAW Veral Si10Mg(0) (Prop.) [Ac] -+ Veral Mg9(H) (Prop.) [Ac] -+
CEN 5182, 182 AA 360.2, 239 AA 518.2,243
VAW 63/45, 148
VAW Veral Si12(0) (Prop.) [Ac]-+ Veral Mg10(H) (Prop.) [Ac] -+
VAW 63/52 (Prop.) [Aw] -+ AAA413.1,263 AA 520.2, 243
AA 5052, 177
VAW Veral Si12A (Prop.) [Ac] -+ Veral MgSi3(H) (Prop) [Ac] -+
CEN 5052, 177 AA 512.2,242
AA A413.2, 263
VAW 63/52, 148
VAW Veral Si12CuNiMg (Prop) [Ac]-+ Veral Si10Mg(0) (Prop.) [Ac] -+
AA 336.1 , 238 AA 360.2, 239
Alloy Cross-Reference Listing 503
Veral Si12(0) (Prop.) [Ae] + Wk. 3.70S5 DIN (D) [Tew] + ZCM711 (UK) [Mw] +
AAA413.1,263 ASTM Grade 4, 333 ASTMZC71,313
Veral Si12A (Prop.) [Ae] + Timetal 100A, 323 ZCM711 - Mag. Elek. (Prop.) [Mw] +
AA A413.2, 263 Wk. 3.70S5 OIN (0) [Tw] + ASTM ZC71, 313
Veral Si12CuNiMg (Prop.) [Ae] + ASTM Grade 4, 332 ZE41A (Prop.) [Me] +
AA 336.1, 238 Timetal 75A, 323 AECMA MG-C-43, 311
Veral Si12CuNiMg(H) (Prop.) [Ae] + Wk. 3.7175 DIN (D) [Tw] + ASTM ZE41A, 314
AA 336.2, 238 AMS 4918, 327 BS MAG5, 310
Veral Si17Cu4Mg(H) (Prop.) [Ae] + Wk. 3.7195 DIN (D) [Tw] + DIN Wk. 3.5101, 297
ASTM 3AI-2.5V, 321 Magnesium Elektron ZE41, 305
AA A390.1, 263
ASTM Grade 9, 333 NF G-Z4TR, 306
Veral Si1BCuNiMg(H) (Prop.) [Ae] + Timetal 3-2.5, 318 ZE41A ASTM (USA) [Me] +
AA 393.2, 241
VT51 (ex USSR) [Tw] + WW-T-700/3 [Aw] + AECMA MG-C-43, 311
AA 2024,161 ASTM ZE41A, 314
AMS 4909, 327 BS MAG5, 310
Alusuisse Avional150, 219
AMS 4924, 327 Alusuisse Avional 152, 219 DIN Wk. 3.5101, 297
VT51,344 CEN 2024, 162 NF G-Z4TR, 306
DIN Wk. 3.1355 (AICuMg2), 144 ZE41A-T5 ASTM (USA) [Me] +
w Hoogovens 2240, 165 Magnesium Elektron ZE41 , 305
NF A-U4G1, 218 ZE63A ASTM (USA) [Me) +
W3120 UNE (E) [Aw] + WW-T-700/S [Aw] + ASTM ZE63A, 314
AA 2017A, 161 AA 6061, 191 ZGS2 CSA (Can) [Aw] +
Alusuisse Avional100, 218 Alusuisse Anticorodal 080, 216 AA 7075,203
AlusuisseAvional-102,218 Alusuisse Anticorodal-082, 216 Alusuisse Perunal215, 226
CEN 2017A, 161 CEN 6061, 192 CEN 7075, 204
NF A-U4G, 218 DIN Wk. 3.3211 (AIMg1SiCu), 145 DIN Wk. 3.4365 (AIZnMgCu1.5), 147
Hoogovens 6560, 198
W3501 DIN (D) [Mw] + Reynolds R-2000, 227
Hoogovens 7750, 207
ASTM MIA, 312 ZGS2 Alclad CSA (Can) [Aw) +
WE43A ASTM (USA) [Mew] +
WW-T-825B [Mw] + AA 7075 Alclad, 204
Magnesium Elecktron AZ61, 301
ASTM WE43A, 313 ZHS2A ASTM (USA) [Me) +
WE43A-TS ASTM (USA) [Mew] + ASTM ZH62A, 314
Magnesium Elektron WE43, 305 x BS MAG9, 310
WE54 ASTM (USA) [Me] + X8011 AA (USA) [Aw] + ZK21A ASTM (USA) [Mw] +
BS MAG14, 311 VAW 98/50, 149 ASTM ZK21A, 314
WE54A ASTM (USA) [Mew] + XC750 Old AA (USA) [Ae] + ZK40A ASTM (USA) [Mw) +
ASTM WE54A, 313 AA 853.0, 245 ASTM ZK40A, 314
Magnesium Elektron WE54, 305 AA 853.2, 245 ZK51A ASTM (USA) [Me) +
Weldalite 049 (Prop.) [Aw] + XC850.0 Old AA (USA) [Ae] + ASTM ZK51A, 314
AA 2095, 163 AA 853.0, 245 BS MAG4, 310
Reynolds Weldalite 049, 229 XC850.2 Old AA (USA) [Ae] + ZK60A ASTM (USA) [Mw) +
Wk. 3.3525 DIN (D) [Aw] + AA 853.2, 245 ASTM ZK60A, 315
Alusuisse Peraluman-226, 223 BS MAG-x-161 , 309
Wk. 3.5101 DIN (D) [Me] + z DIN Wk. 3.5161, 297
AECMA MG-C-43, 311 NF G-Z5Zr, 306
ASTM ZE41A, 314 Z5Z NF (F) [Me] + ZK61A ASTM (USA) [Me) +
BS MAG5, 310 ASTM ZK51A, 314 ASTM ZK61A, 315
DIN Wk. 3.5101, 297 BS MAG4, 310 ZM21 ASTM (USA) [Mw] +
NF G-Z4TR, 306 Z5Z - Mag. Elek. (Prop.) [Me] + ASTM ZM21, 315
Wk. 3.5102 DIN (D) [Me] + BS MAG4, 310 BS MAG-x-131, 308
ASTM ZH62A, 314 ASTM ZK51A, 314 ZRE1 NF (F) [Me) +
BS MAG9, 310 Z132 Old AA (USA) [Ae] + AECMA MG-C-91, 311
Wk. 3.5103 DIN (D) [Me] + AA 339.0,238 ASTM EZ33A, 306
AECMA MG-C-91, 311 AA 339.1, 238 BS MAG6, 310
DIN Wk. 3.5103, 297
ASTM EZ33A, 306 Z332.0 Old AA (USA) [Ae] +
BS MAG6, 310 Magnesium Elektron EZ33, 304
AA 339.0, 238
DIN Wk. 3.5103, 297 ZRE1 (Prop.) [Me) +
Z332.1 Old AA (USA) [Ae] +
Wk. 3.5105 DIN (D) [Me] + AA 339.1, 238
AECMA MG-C-91, 311
ASTM HZ32A, 307 ASTM EZ33A, 306
BS MAG8, 310
ZC63A ASTM (USA) [Me] + BS MAG6, 310
ASTM ZC63A, 313 DIN Wk. 3.5103, 297
Wk. 3.510S DIN (D) [Me] +
ZC63A-T6 ASTM (USA) [Me] + Magnesium Elektron EZ33, 304
ASTM QE22A, 312
BS MAG13, 310
Magnesium Elektron ZC63, 305 ZT1 NF (F) [Me)+
Wk. 3.5812 DIN (D) [Me] + ZC71 (UK) [Mew] + ASTM HZ32A, 307
BS MAG3, 309 ASTM ZC71A, 314 BS MAG8, 310
ASTM AZ91 0, 303 ASTM ZC71, 313 ZW3 - Mag.Elek (Prop.) [Mw] +
DIN Wk. 3.5912, 297 Magnesium Elektron ZC71, 313 Magnesium Elektron ZW3, 315
NF G-A9Z1, 306 ZC71 ASTM (USA) [Mw] + ZW6 - Mag.Elek (Prop.) [Me) +
Wk. 3.7035 DIN (D) [Te] + ASTM ZC71, 313 ASTM ZK61A, 315
NF T 40,336 ZC71A ASTM (USA) [Mew] + ZW6 - Mag.Elek (Prop.) [Mw) +
Wk. 3.7035 DIN (D) [Tew] + ASTM ZC71A, 314 ASTM ZK60A, 315
Timetal 50A, 323 ZC71A-T6 ASTM (USA) [Mw] + BS MAG-x-161, 309
Wk. 3.7035 DIN (D) [Tw] + Magnesium Elektron ZC71, 313 DIN Wk. 3.5161, 297
ASTM Grade 2, 332 ZCM630 (UK) [Me] + NF G-Z5Zr, 306
Magnesium Elektron ZC63, 305
505
03 (British Alcan (AHDE)) [Aw], 143 183 (Alusingen) [Aw], 150 301.0 (AA) [Ac] , 236
2L99 (BS) [Ac], 233 184 (Alusingen) [Aw], 150 301.1 (AA)[Ac] , 236
2L 121 (BS) [Mw] , 297 201.1 (AA) [Ac], 233 302.0 (AA)[Ac] , 236
2TA1 (BS) [Tw], 317 201.2 (AA) [Ac], 233 302.1 (AA)[Ac] , 236
2TA10 (BS) [Tw], 317 202.0 (AA) [Ac], 233 303.0 (AA)[Ac] , 236
2TA21 (BS) [Tw], 317 202.2 (AA) [Ac], 233 303.1 (AA)[Ac] , 236
3 (British Alcan (AHDE)) [Aw], 143 203.0 (AA) [Ac], 233 305.0 (AA)[Ac], 236
3-2.5 (Timetal) [Tw], 318 203.2 (AA) [Ac], 233 305.2 (AA)[Ac], 236
3AI-2.5V (ASTM) [Tw], 321 204.0 (AA) [Ac], 234 308.0 (AA) [Ac], 236
3.5312 (DIN) [Mw] , 297 204.2 (AA) [Ac] , 234 308.1 (AA) [Ac], 236
3.5612 (DIN) [Mw] , 297 205 (Alusingen) [Aw], 150 308.2 (AA) [Ac], 236
3.5812 (DIN) [Mw] , 297 206.0 (AA) [Ac], 234 314A (IMI) [Tw], 324
6-2-4-2 (Timetal) [Tw], 321 206.2 (AA) [Ac] , 234 315 (lMI) [Tw], 324
6-2-4-6 (Timetal) [Tw], 321 208.0 (AA) [Ac], 234 318.0 (AA) [Ac] , 236
6-4 (Timetal) [Tcw], 321 208.1 (AA) [Ac], 234 318.1 (AA) [Ac] , 236
6-6-2 (Timetal) [Tw], 321 208.2 (AA) [Ac], 234 319.0 (AA) [Ac] , 237
/7 (ASTM) [Tw], 321 213.0 (AA) [Ac], 234 319.1 (AA) [Ac] , 237
8-1-1 (Timetal) [Tw], 322 213.1 (AA) [Ac] , 234 319.2 (AA) [Ac] , 237
10-2-3 (Timetal) [Tw], 322 214 (Alusingen) [Aw], 150 320.0 (AA) [Ac] , 237
15-3 (Timetal) [Tw], 322 222.0 (AA) [Ac] , 234 320.1 (AA) [Ac] , 237
17 (Timetal) [Tcw] , 322 222.1 (AA) [Ac], 234 324.0 (AA) [Ac] , 237
21S (Timetal) [Tw], 322 224.0 (AA) [Ac], 234 324.1 (AA) [Ac] , 237
21SRx (Timetal) [Tw], 322 224.2 (AA) [Ac], 234 324.2 (AA) [Ac] , 237
35A (Timetal) [Tw], 322 234 (Alusingen) [Aw], 150 328.0 (AA) [Ac] , 237
41104 (VAW) [Aw], 147 238.0 (AA) [Ac], 234 328.1 (AA) [Ac] , 237
41/20 (VAW) [Aw] , 148 238.1 (AA) [Ac], 234 332.0 (AA) [Ac] , 237
50A (Timetal) [Tcw], 323 238.2 (AA) [Ac], 234 332.1 (AA) [Ac], 237
54 (British Alcan (AHDE)) [Aw], 148 240.0 (AA) [Ac] , 235 332.2 (AA) [Ac] , 237
57 (British Alcan (AHDE)) [Aw], 148 240.1 (AA) [Ac], 235 333.0 (AA) [Ac] , 237
61/03 (VAW) [Aw], 148 242.0 (AA) [Ac], 235 333.1 (AA) [Ac], 238
61/10 (VAW) [Aw], 148 242.1 (AA) [Ac] , 235 336.0 (AA) [Ac] , 238
61/15 (VAW) [Aw], 148 242.2 (AA) [Ac] , 235 336.1 (AA) [Ac], 238
62S (Timetal) [Tw], 323 243.0 (AA) [Ac], 235 336.2 (AA) [Ac], 238
63/37 (VAW) [Aw], 148 243.1 (AA) [Ac], 235 339.0 (AA) [Ac] , 238
63/45 (VAW) [Aw], 148 249.0 (AA) [Ac], 235 339.1 (AA) [Ac], 238
63/52 (VAW) [Aw], 148 249.2 (AA) [Ac], 235 343.0 (AA) [Ac] , 238
65A (Timetal) [Tcw], 323 276 (Alusingen) [Aw], 150 343.1 (AA) [Ac]. 238
75A (Timetal) [Tw], 323 277 (Alusingen) [Aw], 150 354.0 (AA) [Ac] , 238
98/50 (VAW) [Aw], 149 278 (Alusingen) [Aw], 150 354.1 (AA) [Ac] , 238
99/00 (VAW) [Aw], 149 281 (Alusingen) [Aw], 150 355.0 (AA) [Ac] , 238
99/01 (VAW) [Aw], 149 282 (Alusingen) [Aw], 150 355.1 (AA) [Ac] , 238
99/52 (VAW) [Aw], 149 288 (Alusingen) [Aw], 150 355.2 (AA) [Ac] , 238
100A (Timetal) [Tcw], 323 230 (Timetal) [Tw], 324 356.0 (AA) [Ac], 239
100.1 (AA) [Ac], 233 285 (Alusingen) [Aw], 150 356.1 (AA) [Ac], 239
111 (Alusingen) [Aw], 149 286 (Alusingen) [Aw], 150 356.2 (AA) [Ac], 239
119 (Alusingen) [Aw], 149 289 (Alusingen) [Aw], 150 357.0 (AA) [Ac] , 239
129 (Transage) [Tw], 323 294 (Alusingen) [Aw], 151 357.1 (AA) [Ac] , 239
130.1 (AA) [Ac], 233 295.0 (AA) [Ac], 235 358.0 (AA) [Ac] , 239
134 (Transage) [Tw], 323 295.1 (AA) [Ac] , 235 358.2 (AA) [Ac] , 239
134 (Alusingen) [Aw], 149 295.2 (AA) [Ac] , 235 359.0 (AA) [Ac] , 239
150. 1 (AA) [Ac] , 233 296.0 (AA) [Ac] , 235 359.2 (AA) [Ac] , 239
160.1 (AA) [Ac], 233 296.1 (AA) [Ac] , 235 360.0 (AA) [Ac] , 239
170.1 (AA) [Ac], 233 296.2 (AA) [Ac], 236 360.2 (AA) [Ac] , 239
175 (Transage) [Tw], 324 297 (Alusingen) [Aw], 151 361.0 (AA) [Ac], 239
506 Index of Alloy Names and Designations
361.1 (AA) [Ac], 239 520.2 (AA) [Ac], 243 1085 (AA) [Aw], 153
363.0 (AA) [Ac], 239 535.0 (AA) [Ac], 243 1085 (CEN) [Aw], 153
363.1 (AA) [Ac], 240 535.2 (AA) [Ac], 243 1085 (Lawson Mardon (LM) Star) [Aw], 154
364.0 (AA) [Ac], 240 550 (Timetal) [Tw], 324 1090 (AA) [Aw], 154
364.2 (AA) [Ac], 240 551 (IMI) [Tw], 324 1090 (CEN) [Aw], 154
367 (IMI) [Tw], 324 551 (Timetal) [Tw], 325 1095 (AA) [Aw], 154
367 (Timetal) [Tw], 324 646 (IMI) [Tw], 325 1098 (AA) [Aw], 154
369.0 (AA) [Ac], 240 679 (IMI) [Tw], 325 1099 (AA) [Aw], 154
369.1 (AA) [Ac], 240 679 (Timetal) [Tw], 325 1100 (AA) [Aw], 154
380.0 (AA) [Ac], 240 680 (IMI) [Tw], 325 1100 (CEN) [Aw], 154
380.2 (AA) [Ac], 240 685 (IMI) [Tw], 325 1100 (Timetal) [Tw], 326
383.0 (AA) [Ac], 240 685 (Timetal) [Tw], 325 1110 (AA) [Aw], 154
383.1 (AA) [Ac], 240 700 (IMI) [Tw], 325 1120 (AA) [Aw], 154
383.2 (AA) [Ac], 240 705.0 (AA) [Ac], 244 1130 (AA) [Aw], 154
384.0 (AA) [Ac], 240 705.1 (AA) [Ac], 244 1135 (AA) [Aw], 154
384.1 (AA) [Ac], 240 707.0 (AA) [Ac], 244 1145 (AA) [Aw], 154
384.2 (AA) [Ac], 240 707.1 (AA) [Ac], 244 1150 (AA) [Aw], 154
385.0 (AA) [Ac], 240 7100 (AA) [Ac], 244 1160 (AA) [Aw], 155
385.1 (AA) [Ac], 241 710 1 (AA) [Ac], 244 1165 (AA) [Aw], 155
390 (Reynolds) [Aw], 151 7110 (AA) [Ac], 244 1170 (AA) [Aw], 155
390.0 (AA) [Ac], 241 711.1 (AA) [Ac], 244 1175 (AA) [Aw], 155
390.2 (AA) [Ac], 241 712.0 (AA) [Ac], 244 1180 (AA) [Aw], 155
392.0 (AA) [Ac], 241 712.2 (AA) [Ac], 244 1185 (AA) [Aw], 155
392.2 (AA) [Ac], 241 713.0 (AA) [Ac], 244 1187 (AA) [Aw], 155
393.0 (AA) [Ac], 241 713.1 (AA) [Ac], 244 1188 (AA) [Aw], 155
393.1 (AA) [Ac], 241 7168 (8S) [Ac], 244 1190 (AA) [Aw], 155
393.2 (AA) [Ac], 241 771.0 (AA) [Ac], 244 1193 (AA) [Aw], 155
404N (Toyal Europe) [Ap], 295 771.2 (AA) [Ac], 245 1197 (AA) [Aw], 155
405 (Toyal Europe) [Ap], 295 772.0 (AA) [Ac], 245 1198 (AA) [Aw], 155
406S (Toyal Europe) [Ap], 295 772.2 (AA) [Ac], 245 1198 (CEN) [Aw], 155
408.2 (AA) [Ac], 241 829 (IMI) [Tw], 326 1199 (AA) [Aw], 155
409.2 (AA) [Ac], 241 829 (Timetal) [Tw], 326 1199 (CEN) [Aw], 155
411.2 (AA) [Ac], 241 834 (IMI) [Tw], 326 1200 (AA) [Aw], 156
413.0 (AA) [Ac], 241 834 (Timetal) [Tw], 326 1200 (CEN) [Aw], 156
413.1 (AA) [Ac], 241 850.0 (AA) [Ac], 245 1200A (AA) [Aw], 156
416 (Toyal Europe) [Ap], 295 850.1 (AA) [Ac], 245 1201 (Lawson Mardon (LM) Star) [Aw], 156
420 (Timminco) [Acw], 151,241 8510 (AA) [Ac], 245 1230 (AA) [Aw], 156
432S (Toyal Europe) [Ap], 295 851.1 (AA) [Ac], 245 1235 (AA) [Aw], 156
435.2 (AA) [Ac], 242 852.0 (AA) [Ac], 245 1245 (AA) [Aw], 156
443.0 (AA) [Ac], 242 852.1 (AA) [Ac], 245 1250 (AA) [Aw], 156
443.1 (AA) [Ac], 242 853.0 (AA) [Ac], 245 1260 (AA) [Aw], 157
443.2 (AA) [Ac], 242 853.2 (AA) [Ac], 245 1270 (AA) [Aw], 157
444.0 (AA) [Ac], 242 1000 (Hoogovens) [Aw], 151 1275 (AA) [Aw], 157
444.2 (AA) [Ac], 242 1000 (Timetal) [Tw], 326 1285 (AA) [Aw], 157
445.2 (AA) [Ac], 242 1001 (Hoogovens) [Aw], 151 1330 (AA) [Aw], 157
455 (Toyal Europe) [Ap], 295 1010 (Hoogovens) [Aw], 151 1335 (AA) [Aw], 157
462 (Toyal Europe) [Ap], 295 1030 (AA) [Aw], 151 1345 (AA) [Aw], 157
511.0 (AA) [Ac], 242 1035 (AA) [Aw], 151 1350 (AA) [Aw], 157
511.1 (AA) [Ac], 242 1040 (AA) [Aw], 151 1350 (CEN) [Aw], 157
511.2 (AA) [Ac], 242 1045 (AA) [Aw], 151 1350A (AA) [Aw], 157
512.0 (AA) [Ac], 242 1050 (AA) [Aw], 151 1360 (AA) [Aw], 157
512.2 (AA) [Ac], 242 1050A (AA) [Aw], 152 1370 (AA) [Aw], 157
513.0 (AA) [Ac], 242 1050A (CEN) [Aw], 152 1370 (CEN) [Aw], 157
513.2 (AA) [Ac], 242 1055 (AA) [Aw], 152 1370-70 (Alunord) [Aw], 158
514.0 (AA) [Ac], 243 1060 (AA) [Aw], 152 1385 (AA) [Aw], 158
514.1 (AA) [Ac], 243 1065 (AA) [Aw], 152 1435 (AA) [Aw], 158
514.2 (AA) [Ac], 243 1070 (AA) [Aw], 152 1445 (AA) [Aw], 158
515.0 (AA) [Ac], 243 1070 (Hoogovens) [Aw], 153 1450 (AA) [Aw], 158
515.2 (AA) [Ac], 243 1070A (AA) [Aw], 153 1602 (Lawson Mardon (LM) Star) [Aw], 158
516.0 (AA) [Ac], 243 1070A (CEN) [Aw], 153 2001 [Aw],
(AA) 158
516.1 (AA) [Ac], 243 1075 (AA) [Aw], 153 2002 [Aw],
(AA) 158
518.0 (AA) [Ac], 243 1080 (AA) [Aw], 153 2003 [Aw],
(AA) 158
518.1 (AA) [Ac], 243 1080A (AA) [Aw], 153 2004 [Aw],
(AA) 158
518.2 (AA) [Ac], 243 1080A (CEN) [Aw], 153 2005 (AA) [Aw], 158
520.0 (AA) [Ac], 243 1084 (Lawson Mardon (LM) Star) [Aw], 153 2006 (AA) [Aw], 158
Index of Alloy Names and Designations 507
2007 [Aw], 158
(AA) 3000 (Hoogovens) [Aw], 166 3530 Clad (Hoogovens) [Aw], 170
2008 [Aw], 158
(AA) 3000 Clad (Hoogovens) [Aw] , 166 3540 (Hoogovens) [Aw], 171
2009 [Aw] , 158
(AA) 3002 (AA) [Aw], 166 3540 Clad (Hoogovens) [Aw], 171
2010 [Aw], 158
(AA) 3003 (AA) [Aw], 166 3541 (Hoogovens) [Aw], 171
2011 [Aw], 159
(AA) 3003 (CEN) [Aw] , 167 3560 Clad (Hoogovens) [Aw] , 171
2011 (CEN) [Aw] , 159 3003 (NF) [Aw], 167 3599 (UNI) [Ac] , 247
2011A (AA) [Aw] , 159 3003 Alclad (AA) [Aw], 167 3600 (UNI) [Ac], 247
2011 A (CEN) [Aw], 159 3004 (AA) [Aw], 167 3601 (UNI) [Ac], 247
2012 (AA) [Aw], 159 3004 (CEN) [Aw], 167 3602 (UNI) [Ac], 247
2014 (AA) [Aw], 159 3004 Alclad (AA) [Aw], 168 3620-TA7 (-) [Tcw], 326
2014 (CEN) [Aw] , 160 3004A (AA) [Aw], 168 3620-TA7 [Tcw], 326
2014 Alclad (AA) [Aw], 160 3005 (AA) [Aw] , 168 4001 (AA) [Aw] , 171
2014A (AA) [Aw], 160 3005 (CEN) [Aw], 168 4002 (AA) [Aw] , 171
2017 (AA) [Aw] , 160 3005 Alclad (AA) [Aw], 168 4004 (AA) [Aw] , 171
2017A (AA) [Aw], 161 3006 (AA) [Aw], 168 4004 (CEN) [Aw], 171
2017A (CEN) [Aw], 161 3007 (AA) [Aw] , 168 4006 (AA) [Aw], 171
2018 (AA) [Aw], 161 3008 (AA) [Aw], 168 4006 (CEN) [Aw] , 171
2020 (AA) [Aw], 161 3009 (AA) [Aw], 168 4007 (AA) [Aw], 171
2021 (AA) [Aw], 161 3010 (AA) [Aw], 168 4007 (CEN) [Aw] , 171
2024 (AA) [Aw], 161 3010 (Hoogovens) [Aw], 168 4008 (AA) [Aw], 171
2024 (CEN) [Aw], 162 3011 (AA) [Aw], 168 4009 (AA) [Aw], 171
2024 Alclad (AA) [Aw], 162 3012 (AA) [Aw], 168 4010 (AA) [Aw], 171
2024A (AA) [Aw], 162 3013 (AA) [Aw] , 169 4011 (AA) [Aw], 171
2025 (AA) [Aw], 162 3014 (AA) [Aw], 169 4012 (AA) [Aw], 172
2030 (AA) [Aw], 162 3015 (AA) [Aw], 169 4013 (AA) [Aw], 172
2030 (CEN) [Aw], 162 3016 (AA) [Aw], 169 4014 (AA) [Aw], 172
2031 (AA) [Aw], 163 3017 (AA) [Aw], 169 4015 (AA) [Aw], 172
2034 (AA) [Aw], 163 3018 (AA) [Awl. 169 4016 (AA) [Aw], 172
2036 (AA) [Aw], 163 3040 (UN I) [Ac], 245 4017 (AA) [Aw], 172
2037 (AA) [Aw], 163 3041 (UNI) [Ac] , 245 4018 (AA) [Aw] , 172
2038 (AA) [Aw], 163 3042 [Ac] , 245
(UNI) 4032 (AA) [Aw], 172
2048 (AA) [Aw], 163 3043 [Ac] , 246
(UNI) 4043 (AA) [Aw], 172
2053 (AA) [Aw], 163 3044 (UNI)
[Ac] , 246 4043A (AA) [Aw], 172
2080 (AA) [Aw], 163 3045 [Ac] , 246
(UNI) 4043A (CEN) [Aw], 172
2090 (AA) [Aw], 163 3046 (UNI)
[Ac], 246 4044 (AA) [Aw], 172
2091 (AA) [Aw], 163 3048 (UNI) [Ac] , 246 4045 (AA) [Aw] , 172
2094 (AA) [Aw], 163 3049 (UNI) [Ac] , 246 4045 (CEN) [Aw], 172
2095 (AA) [Aw], 163 3050 (UNI) [Ac] , 246 4046 (AA) [Aw], 172
2097 (AA) [Aw] , 163 3051 (UNI) [Ac] , 246 4047 (AA) [Aw] , 173
2111 (AA) [Aw], 163 3052 (UNI) [Ac], 246 4047A (AA) [Aw], 173
2117 (AA) [Aw], 164 3054 (UNI) [Ac] , 246 4047A (CEN) [Aw], 173
2124 (AA) [Aw], 164 3055 (UNI) [Ac], 246 4048 (AA) [Aw], 173
2124 (CEN) [Aw], 164 3056 (UNI) [Ac], 246 4020 (SIS) [Ac] , 247
2140 (Hoogovens) [Aw], 164 3057 (UNI) [Ac], 246 4021 (SIS) [Ac], 247
2170 (Hoogovens) [Aw], 164 3058 (UNI) [Ac] , 246 4022 (SIS) [Ac] , 247
2195 (AA) [Aw], 164 3059 (UNI) [Ac], 247 4024 (SIS) [Ac] , 247
2197 (AA) [Aw], 164 3102 (AA) [Aw] , 169 4101 (AA) [Aw], 173
2214 (AA) [Aw], 164 3103 (AA) [Aw], 169 4104 (AA) [Aw], 173
2214 (CEN) [Aw], 164 3103 (CEN) [Aw], 169 4104 (CEN) [Aw], 173
2218 (AA) [Aw], 164 3103 (Lawson Mardon (LM) Star) [Aw], 169 4145 (AA) [Aw], 173
2219 (AA) [Aw], 165 3103A (AA) [Aw] , 169 4145A (AA) [Aw] , 173
2219 (CEN) [Aw], 165 3104 (AA) [Aw], 169 4147 (AA) [Aw], 173
2224 (AA) [Aw], 165 3104 (CEN) [Aw], 169 4162 (DS) [Ac] , 247
2225 (AA) [Aw], 165 3105 (AA) [Aw], 170 4163 (DS) [Ac], 247
2240 (Hoogovens) [Aw], 165 3105 (CEN) [Aw] , 170 4245 (AA) [Aw], 173
2319 (AA) [Aw], 165 3105A (AA) [Aw] , 170 4244 (DS) [Ac], 247
2324 (AA) [Aw] , 165 3107 (AA) [Aw], 170 4251 (DS) [Ac] , 247
2419 (AA) [Aw], 165 3203 (AA) [Aw], 170 4253 (DS) [Ac], 247
2424 (AA) [Aw], 165 3204 (AA) [Aw], 170 4254 (DS) [Ac] , 247
2519 (AA) [Aw], 165 3205 (AA) [Aw], 170 4260 (DS) [Ac] , 248
2524 (AA) [Aw] , 165 3207 (AA) [Aw] , 170 4261 (DS) [Ac], 248
2618 (AA) [Aw], 165 3207A (AA) [Aw], 170 4343 (AA) [Aw], 173
261BA (AA) [Aw], 166 3303 (AA) [Aw] , 170 4343 (CEN) [Aw] , 173
2618A (CEN) [Aw], 166 3307 (AA) [Aw], 170 4438 (DS) [Ac], 248
2564 (SFS) [Ac] , 245 3530 (Hoogovens) [Aw], 170 4543 (AA) [Aw], 173
508 Index of Alloy Names and Designations
4513 (UNI) [Ae], 248 5082 (AA) [Aw], 178 5510 (Hoogovens) [Aw], 185
4514 (UN I) [Ae], 248 5083 (AA) [Aw], 178 5520 (Hoogovens) [Aw], 185
4643 (AA) [Aw], 173 5083 (CEN) [Aw], 179 5552 (AA) [Aw], 185
4905 (AMS) [Tw], 326 5083 SPF (Superform Metals) [Aw], 179 5554 (AA) [Aw], 186
4907 (AMS) [Tw], 327 5083 (OTO) [Tw], 328 5556 (AA) [Aw], 186
4909 (AMS) [Tw] , 327 5086 (AA) [Aw], 179 5556A (AA) [Aw], 186
4910 (AMS) [Tw], 327 5086 (CEN) [Aw], 180 5557 (AA) [Aw], 186
4915 (AMS) [Tw], 327 5087 (AA) [Aw], 180 5605 (AA) [Aw], 186
4918 (AMS) [Tw], 327 5087 (CEN) [Aw], 180 5652 (AA) [Aw], 186
4919 (AMS) [Tw], 327 5091 (AA) [Aw], 180 5654 (AA) [Aw], 186
4924 (AMS) [Tw], 327 5105 (AA) [Aw], 180 5657 (AA) [Aw], 186
4926 (AMS) [Tw], 328 5110 (AA) [Aw], 180 5657 (CEN) [Aw], 186
4974 (AMS) [Tw], 328 5111 (Timetal) [Tw], 328 5754 (AA) [Aw], 187
5004 (AA) [Aw], 173 5119 (AA) [Aw], 180 5754 (CEN) [Aw], 187
5005 (AA) [Aw], 174 5149 (AA) [Aw], 180 5757 (AA) [Aw], 188
5005 (CEN) [Aw], 174 5150 (AA) [Aw], 180 5854 (AA) [Aw], 188
5005A (AA) [Aw], 174 5151 (AA) [Aw], 180 5857 (AA) [Aw], 188
5006 (AA) [Aw], 174 5152 (AA) [Aw], 181 5954 [Aw], 188
(AA)
5007 (AA) [Aw], 174 5154 (AA) [Aw], 181 5957 [Aw], 188
(AA)
5008 (AA) [Aw], 174 5154A (AA) [Aw], 181 6001 [Aw], 188
(AA)
5008B (BS) [Ae], 248 5154A (CEN) [Aw], 181 6002 [Aw], 188
(AA)
5009 (AA) [Aw], 174 5154B (AA) [Aw], 181 6003 (AA) [Aw], 188
5010 (AA) [Aw], 174 5155 (AA) [Aw], 181 6004 (AA) [Aw], 188
5010 (Hoogovens) [Aw], 174 5163 (OTD) [Tw], 328 6005 (AA) [Aw], 188
5011 (AA) [Aw], 175 5180 (AA) [Aw], 181 6005A (AA) [Aw], 188
5013 (AA) [Aw], 175 5182 (AA) [Aw], 181 6005A (Alunord) [Aw], 188
5014 (AA) [Aw], 175 5182 (CEN) [Aw], 182 6005A (CEN) [Aw], 189
5016 (AA) [Aw], 175 5183 (AA) [Aw], 182 6005B (AA) [Aw], 189
5017 (AA) [Aw], 175 5183 (CEN) [Aw], 182 6006 (AA) [Aw], 189
5018 (AA) [Aw], 175 5186 (AA) [Aw], 182 6007 (AA) [Aw], 189
5018A (BS) [Ae], 248 5205 (AA) [Aw], 182 6008 (AA) [Aw], 189
5019 (AA) [Aw], 175 5210 (AA) [Aw], 182 6009 (AA) [Aw], 189
5019 (CEN) [Aw], 175 5249 (AA) [Aw], 182 6010 (AA) [Aw], 189
5020 (Hoogovens) [Aw], 175 5250 (AA) [Aw], 182 6010 (Hoogovens) [Aw], 189
5021 (AA) [Aw], 175 5251 (AA) [Aw], 182 6011 (AA) [Aw], 189
5022 (AA) [Aw], 175 5251 (CEN) [Aw], 183 6012 (AA) [Aw], 189
5023 (AA) [Aw], 175 5251A (AA) [Aw] , 183 6012 (CEN) [Aw], 189
5030 (Hoogovens) [Aw], 175 5252 (AA) [Aw], 183 6013 (AA) [Aw], 189
5034 (AA) [Aw], 175 5254 (AA) [Aw], 183 6014 (AA) [Aw], 189
5039 (AA) [Aw], 175 5257 (AA) [Aw], 183 6015 (AA) [Aw], 189
5040 (AA) [Aw], 175 5280 (AA) [Aw], 183 6016 (AA) [Aw], 190
5042 (AA) [Aw], 176 5283 (AA) [Aw], 183 6016A (AA) [Aw], 190
5043 (AA) [Aw], 176 5283A (AA) [Aw], 183 6017 (AA) [Aw], 190
5049 (AA) [Aw], 176 5305 (AA) [Aw], 183 6018 (AA) [Aw], 190
5049 (CEN) [Aw], 176 5310 (AA) [Aw], 183 6020 (AA) [Aw], 190
5050 (AA) [Aw], 176 5349 (AA) [Aw], 183 6022 (AA) [Aw], 190
5050 (CEN) [Aw], 176 5351 (AA) [Aw], 183 6051 (AA) [Aw], 190
5050A (AA) [Aw], 176 5352 (AA) [Aw], 183 6053 (AA) [Aw] , 190
5050B (AA) [Aw], 176 5354 (AA) [Aw], 184 6056 (AA) [Aw], 190
5051 (AA) [Aw), 176 5356 (AA) [Aw], 184 6056 (CEN) [Aw], 190
5051A (AA) [Aw], 176 5356 (CEN) [Aw], 184 6060 (AA) [Aw], 190
5051A (CEN) [Aw], 176 5357 (AA) [Aw], 184 6060 (CEN) [Aw], 190
5052 (AA) [Aw], 177 5383 (AA) [Aw], 184 6060.48 (Alunord) [Aw], 191
5052 (CEN) [Aw], 177 5400 (Hoogovens) [Aw], 184 6060.79 (Alunord) [Aw], 191
5053 (AA) [Aw], 177 5405 (AA) [Aw], 184 6061 (AA) [Aw], 191
5053 (OTD) [Tw], 328 5449 (AA) [Aw], 184 6061 (CEN) [Aw], 192
5056 (AA) [Aw], 177 5451 (AA) [Aw], 184 6061A (AA) [Aw], 192
5056A (AA) [Aw], 178 5454 (AA) [Aw], 184 6062 (AA) [Aw], 192
5058 (AA) [Aw], 178 5454 (CEN) [Aw], 185 6063 (AA) [Aw], 193
5074-74 (UN I) [Ae], 248 5456 (AA) [Aw], 185 6063 (CEN) [Aw], 193
5075-74 (UN I) [Ae], 248 5456A (AA) [Aw], 185 6063A (AA) [Aw], 193
5076-74 (UNI) [Ae), 248 5456A (CEN) [Aw), 185 6066 (AA) [Aw], 193
5077-74 (UNI) [Ae), 248 5457 (AA) [Aw), 185 6069 (AA) [Aw), 193
5079-74 (UNI) [Ae), 248 5503 (Hoogovens) [Aw], 185 6070 (AA) [Aw], 193
5080-74 (UNI) [Ae], 248 5505 (AA) [Aw], 185 6071 (AA) [Aw], 194
Index of Alloy Names and Designations 509
6081 (AA) [Aw], 194 7012 [Aw], 199
(AA) 7179 (AA) [Aw], 206
6081-11 (Alunord) [Aw], 194 7013 [Aw], 199
(AA) 7229 (AA) [Aw], 206
6082 (AA) [Aw], 194 7014 [Aw], 199
(AA) 7249 (AA) [Aw], 206
6082 (CEN) [Aw], 195 7015 [Aw], 199
(AA) 7277 (AA) [Aw], 206
6082A (AA) [Aw], 195 7016 [Aw], 199
(AA) 7278 (AA) [Aw], 206
6082-50 (Alunord) [Aw], 195 7017 [Aw], 200
(AA) 7278A (AA) [Aw], 206
6090 (AA) [Aw], 195 7018 (AA) [Aw], 200 7257 (UNI) [Ac], 249
6091 (AA) [Aw], 195 7019 (AA) [Aw], 200 7349 (AA) [Aw], 206
6092 (AA) [Aw], 195 7019A (AA) [Aw], 200 7350 (Hoogovens) [Aw], 206
6101 (AA) [Aw], 196 7020 (AA) [Aw], 200 7363 (UNI) [Ac], 249
6101 (CEN) [Aw], 196 7020 (CEN) [Aw], 200 7369-74 Part 1 (UNI) [Ac], 249
6101A (AA) [Aw], 196 7021 (AA) [Aw], 200 7369-74 Part 2 (UNI) [Ac], 249
61018 (AA) [Aw], 196 7021 (CEN) [Aw], 201 7369-74 Part 3 (UNI) [Ac], 249
6103 (AA) [Aw], 196 7022 (AA) [Aw], 201 7369-74 Part 4 (UNI) [Ac], 249
6105 (AA) [Aw], 196 7023 (AA) [Aw], 201 7369-74 Part 5 (UNI) [Ac], 249
6106 (AA) [Aw], 196 7024 (AA) [Aw], 201 7369-74 Part 6 (UNI) [Ac], 249
6106 (Alunord) [Aw], 196 7025 (AA) [Aw], 201 7449 (AA) [Aw], 206
6106 (CEN) [Aw], 196 7026 (AA) [Aw], 201 7472 (AA) [Aw], 206
6110 (AA) [Aw], 196 7027 (AA) [Aw], 201 7475 (AA) [Aw], 206
6110A (AA) [Aw], 196 7028 (AA) [Aw], 201 7475 (CEN) [Aw], 207
6111 [Aw], 196
(AA) 7029 [Aw], 201
(AA) 7750 (Hoogovens) [Aw], 207
6113 [Aw], 197
(AA) 7030 [Aw], 201
(AA) 7790 (Hoogovens) [Aw], 207
6116 [Aw], 197
(AA) 7031 [Aw], 201
(AA) 7963 (UN I) [Ac], 249
6151 [Aw], 197
(AA) 7032 [Aw], 201
(AA) 8001 (AA) [Aw], 207
6160 (AA) [Aw], 197 7033 (AA) [Aw], 201 8004 (AA) [Aw], 207
6162 (AA) [Aw], 197 7039 (AA) [Aw], 201 8005 (AA) [Aw], 207
6181 (AA) [Aw], 197 7039 (CEN) [Aw], 201 8006 (AA) [Aw], 207
6201 (AA) [Aw], 197 7040 (AA) [Aw], 201 8006 (CEN) [Aw], 207
6201A (AA) [Aw], 197 7046 (AA) [Aw], 202 8007 (AA) [Aw], 207
6205 (AA) [Aw], 197 7049 (AA) [Aw], 202 8008 (AA) [Aw], 207
6206 (AA) [Aw], 197 7049A (AA) [Aw], 202 8009 (AA) [Aw], 207
6250-68 (UN I) [Ac], 248 7049A (CEN) [Aw], 202 8010 (AA) [Aw], 207
6251-68 (UN I) [Ac], 249 7050 (AA) [Aw], 202 8011 (AA) [Aw], 207
6252-68 (UN I) [Ac], 249 7050 (CEN) [Aw], 202 8011A (AA) [Aw], 207
6253-68 (UNI) [Ac], 249 7050A (AA) [Aw], 202 8011A (CEN) [Aw], 208
6253 (AA) [Aw], 197 7051 (AA) [Aw], 202 8013 (AA) [Aw], 208
6261 (AA) [Aw], 197 7055 (AA) [Aw], 203 8014 (AA) [Aw], 208
6262 (AA) [Aw], 197 7060 (AA) [Aw], 203 8015 (AA) [Aw], 208
6262 (CEN) [Aw], 197 7064 (AA) [Aw], 203 8016 (AA) [Aw], 208
6301 (AA) [Aw], 198 7070 (AA) [Aw], 203 8017 (AA) [Aw], 208
6306 (AA) [Aw], 198 7072 (AA) [Aw], 203 8018 (AA) [Aw], 208
6351 (AA) [Aw], 198 7072 (CEN) [Aw], 203 8019 (AA) [Aw], 208
6351A (AA) [Aw], 198 7075 (AA) [Aw], 203 8020 (AA) [Aw], 208
6363 (AA) [Aw], 198 7075 (CEN) [Aw], 204 8021 (AA) [Aw], 208
6401 (AA) [Aw], 198 7075 Alclad (AA) [Aw], 204 8021A (AA) [Aw], 208
6463 (AA) [Aw], 198 7076 (AA) [Aw], 204 80218 (AA) [Aw], 208
6463A (AA) [Aw], 198 7079 (AA) [Aw], 204 8022 (AA) [Aw], 208
6560 (Hoogovens) [Aw], 198 7090 (AA) [Aw], 205 8024 (UN I) [Ac], 250
6563 (AA) [Aw], 198 7091 (AA) [Aw], 205 8030 (AA) [Aw], 208
6630 Clad (Hoogovens) [Aw], 198 7093 (AA) [Aw], 205 8040 (AA) [Aw], 208
6663 (AA) [Aw], 198 7104 (AA) [Aw], 205 8050 (AA) [Aw], 208
6763 (AA) [Aw], 198 7108 (AA) [Aw], 205 8076 (AA) [Aw], 208
6863 (AA) [Aw], 198 7108A (AA) [Aw], 205 8077 (AA) [Aw], 208
6951 (AA) [Aw], 198 7109 (AA) [Aw], 205 8079 (AA) [Aw], 209
6963 (AA) [Aw], 199 7116 (AA) [Aw], 205 8079 (CEN) [Aw], 209
7001 (AA) [Aw], 199 7129 (AA) [Aw], 205 8081 (AA) [Aw], 209
7002 (AA) [Aw], 199 7139 (AA) [Aw], 205 8090 (AA) [Aw], 209
7003 (AA) [Aw], 199 7146 (AA) [Aw], 205 8091 (AA) [Aw], 209
7004 (AA) [Aw], 199 7149 (AA) [Aw], 205 8093 (AA) [Aw], 209
7005 (AA) [Aw], 199 7149 (CEN) [Aw], 205 8101 (Lawson Mardon (LM) Star) [Aw], 209
7008 (AA) [Aw], 199 7150 (AA) [Aw], 205 8111 (AA) [Aw], 209
7009 (AA) [Aw], 199 7175 (AA) [Aw], 205 8112 (AA) [Aw], 209
7010 (AA) [Aw], 199 7175 (CEN) [Aw], 206 8130 (AA) [Aw], 209
7010 (CEN) [Aw], 199 7178 (AA) [Aw], 206 8176 (AA) [Aw], 209
7011 (AA) [Aw], 199 7178 (CEN) [Aw], 206 8177 (AA) [Aw], 209
510 Index of Alloy Names and Designations
8211 (AA) [Aw], 209 A333.1 (AA) [Ac], 262 AA 242.0 [Ac], 235
8212 (AA) [Aw], 209 A355.0 (AA) [Ac], 262 AA 242.1 [Ae], 235
8276 (AA) [Aw], 209 A355.2 (AA) [Ac], 262 AA 242.2 [Ae], 235
8280 (AA) [Aw], 209 A356 (Hydro Raufoss) [Ae], 262 AA 243.0 [Ae], 235
21000 (CEN) [Ae], 250 A356.0 (AA) [Ac], 262 AA 243.1 [Ae], 235
21100 (CEN) [Ac], 250 A356.1 (AA) [Ae], 262 AA 249.0 [Ae], 235
41000 (CEN) lAc], 250 A356.2 (AA) [Ac], 262 AA 249.2 [Ae], 235
42000 (CEN) [Ae], 250 A357.0 (AA) [Ae], 262 AA 295.0 [Ae], 235
42100 (CEN) [Ac], 250 A357.2 (AA) [Ae], 262 AA 295.1 [Ae], 235
42200 (CEN) [Ae], 250 A359.0 (AA) [Ae], 262 AA 295.2 [Ae], 235
43000 (CEN) [Ae], 251 A359.1 (AA) [Ac], 262 AA 296.0 [Ae], 235
43100 (CEN) [Ae], 251 A360.0 (AA) [Ae], 262 AA 296.1 [Ae], 235
43200 (CEN) lAc], 251 A360.1 (AA) [Ac], 263 AA 296.2 [Ae], 236
43300 (CEN) [Ae], 251 A360.2 (AA) [Ac], 263 AA 301.0 [Ae], 236
43400 (CEN) [Ac], 251 A380.0 (AA) [Ac], 263 AA 301.1 [Ac], 236
44000 (CEN) lAc], 251 A380.1 (AA) [Ae], 263 AA 302.0 [Ac], 236
44100 (CEN) [Ac], 251 A380.2 (AA) [Ae], 263 AA 302.1 [Ae], 236
44200 (CEN) lAc], 251 A383.0 (AA) [Ac], 263 AA 303.0 [Ae], 236
44300 (CEN) [Ac], 252 A383.1 (AA) [Ac], 263 AA 303.1 [Ae], 236
44400 (CEN) [Ae], 252 A384.0 (AA) [Ae], 263 AA 305.0 [Ac], 236
45000 (CEN) [Ac], 252 A384.1 (AA) [Ac], 263 AA 305.2 [Ae], 236
45100 (CEN) [Ae], 252 A390.0 (AA) [Ac], 263 AA 308.0 [Ae], 236
45200 (CEN) [Ae], 252 A390.1 (AA) [Ac], 263 AA 308.1 [Ac], 236
45300 (CEN) [Ac], 252 A413.0 (AA) [Ac], 263 AA 308.2 [Ac], 236
45400 (CEN) [Ac], 252 A413.1 (AA) [Ac], 263 AA 318.0 [Ae], 236
46000 (CEN) [Ac], 252 A413.2 (AA) [Ac], 263 AA 318.1 [Ac], 236
46100 (CEN) [Ac], 253 A443.0 (AA) [Ac], 264 AA 319.0 [Ac], 237
46200 (CEN) [Ac], 253 A443.1 (AA) [Ac], 264 AA 319.1 [Ac], 237
46300 (CEN) [Ac], 253 A444.0 (AA) [Ac], 264 AA 319.2 [Ac], 237
46400 (CEN) [Ac], 253 A444.1 (AA) [Ac], 264 AA 320.0 [Ac], 237
46500 (CEN) [Ac], 253 A444.2 (AA) [Ac], 264 AA 320.1 [Ac], 237
46600 (CEN) [Ac], 253 A535.0 (AA) [Ac], 264 AA 324.0 [Ac], 237
47000 (CEN) [Ac], 253 A535.1 (AA) [Ac], 264 AA 324.1 [Ac], 237
47100 (CEN) [Ac], 253 AA 100.1 [Ac], 233 AA 324.2 [Ac], 237
48000 (CEN) lAc], 254 AA150 (AS) [Ac], 264 AA 328.0 [Ac], 237
51000 (CEN) [Ac], 254 AA 150.1 [Ac], 233 AA 328.1 [Ac], 237
51100 (CEN) [Ac], 254 AA160 (AS) [Ac], 264 AA 332.0 [Ae], 237
51200 (CEN) [Ac], 254 AA 160.1 [Ac], 233 AA 332.1 [Ac], 237
51300 (CEN) [Ac], 254 AA 170.1 [Ac], 233 AA 332.2 [Ac], 237
51400 (CEN) [Ae], 254 AA170 (AS) [Ae], 264 AA 333.0 [Ac], 237
71000 (CEN) [Ac], 254 AA175 (AS) [Ac], 264 AA 333.1 lAc], 238
AA180 (AS) [Ae], 264 AA 336.0 [Ae], 238
AA185 (AS) [Ae], 264 AA 336.1 [Ac], 238
A
AA 201.1 [Ac], 233 AA 336.2 [Ac], 238
A-4 (NF) [Ac], 254 AA 201.2 [Ac], 233 AA 339.0 [Ae], 238
A-5 (NF) [Ac], 254 AA 202.0 [Ac], 233 AA 339.1 lAc], 238
A-5 (NF) [Aw], 210 AA 202.2 [Ac], 233 AA 343.0 [Ac], 238
A-5L (NF) [Aw], 210 AA 203.0 [Ac], 233 AA 343.1 [Ac], 238
A-5/LR (NF) [Ac], 255 AA 203.2 [Ac], 233 AA 354.0 [Ac], 238
A-5 Y4 (NF) [Ac], 255 AA 204.0 [Ac], 234 AA 354.1 [Ac], 238
A-6GBe (NF) [Ac], 255 AA 204.2 [Ac], 234 AA 355.0 [Ac], 238
A-7/LR (NF) [Ac], 255 AA 206.0 [Ac], 234 AA 355.1 [Ac], 238
A2010 (AA) [Ac], 261 AA 206.2 [Ac], 234 AA 355.2 lAc], 238
A201.1 (AA) [Ac], 261 AA 208.0 [Ac], 234 AA 356.0 [Ac], 239
A206.0 (AA) [Ac], 261 AA 208.1 [Ac], 234 AA 356.1 [Ac], 239
A206.2 (AA) [Ac], 261 AA 208.2 [Ac], 234 AA 356.2 [Ae], 239
A242.0 (AA) [Ac], 261 AA 213.0 [Ac], 234 AA 357.0 [Ac], 239
A242.1 (AA) [Ac], 261 AA 213.1 [Ac], 234 AA 357.1 [Ae], 239
A242.2 (AA) [Ac], 261 AA 222.0 [Ac], 234 AA 358.0 [Ae], 239
A305.0 (AA) [Ac], 261 AA 222.1 [Ac], 234 AA 358.2 [Ac], 239
A305.1 (AA) [Ac], 261 AA 238.0 [Ac], 234 AA 359.0 [Ae], 239
A305.2 (AA) [Ac], 261 AA 238.1 [Ac], 234 AA 359.2 [Ac], 239
A319.0 (AA) [Ac], 262 AA 238.2 [Ac], 234 AA 360.0 [Ac], 239
A319.1 (AA) [Ac], 262 AA 240.0 [Ac], 235 AA 360.2 [Ac], 239
A333.0 (AA) [Ac], 262 AA 240.1 [Ac], 235 AA 361.0 lAc], 239
Index of Alloy Names and Designations 511
AA 361.1 [Ae], 239 AA 852.0 [Ae], 245 AA 2001 [Aw], 158
AA 363.0 [Ae], 239 AA 852.1 [Ae], 245 AA 2002 [Aw], 158
AA 363.1 [Ae], 240 AA 853.0 [Ae], 245 AA 2003 [Aw], 158
AA 364.0 [Ae], 240 AA 853.2 [Ae], 245 AA 2004 [Aw], 158
AA 364.2 [Ae], 240 AA 1030 [Aw], 151 AA 2005 [Aw], 158
AA 369.0 [Ae], 240 AA 1035 [Aw] , 151 AA 2006 [Aw], 158
AA 369.1 [Ae], 240 AA 1040 [Aw], 151 AA 2007 [Aw], 158
AA 380.0 [Ae], 240 AA 1045 [Aw] , 151 AA 2008 [Aw], 158
AA 380.2 [Ae], 240 AA 1050 [Aw], 151 AA 2009 [Aw], 158
AA 383.0 [Ae], 240 AA 1050A [Aw], 152 AA 2010 [Aw], 158
AA 383.1 [Ae], 240 AA 1055 [Aw], 152 AA 2011 [Aw], 159
AA 383.2 [Ae] , 240 AA 1060 [Aw] , 152 AA2011A[Aw],159
AA 384.0 [Ae], 240 AA 1065 [Aw], 152 AA 2012 [Aw], 159
AA 384.1 [Ae] , 240 AA 1070 [Aw], 152 AA 2014 [Aw], 159
AA 384.2 [Ae], 240 AA 1070A [Aw], 153 AA 2014 Alclad [Aw], 160
AA 385.0 [Ae], 240 AA 1075 [Aw], 153 AA 2014A [Aw], 160
AA 385.1 [Ae], 241 AA 1080 [Aw], 153 AA 2017 [Aw] , 160
AA 390.0 [Ae], 241 AA 1080A [Aw] , 153 AA 2017A [Aw], 161
AA 390.2 [Ae], 241 AA 1085 [Aw], 153 AA 2018 [Aw] , 161
AA 392.0 [Ae], 241 AA 1090 [Aw], 154 AA 2020 [Aw], 161
AA 392.2 [Ae], 241 AA 1095 [Aw], 154 AA 2021 [Aw], 161
AA 393.0 [Ae], 241 AA 1098 [Aw], 154 AA 2024 [Aw], 161
AA 393,1 [Ae], 241 AA 1099 [Aw] , 154 AA 2024 Alclad [Aw], 162
AA 393.2 [Ae], 241 AA 1100 [Aw], 154 AA 2024A [Aw], 162
AA 408,2 [Ae], 241 AA 1110 [Aw], 154 AA 2025 [Aw], 162
AA 409,2 [Ae] , 241 AA 1120 [Aw], 154 AA 2030 [Aw], 162
AA 411.2 [Ae], 241 AA 1130 [Aw], 154 AA 2031 [Aw], 163
AA 413,0 [Ae] , 241 AA 1135 [Aw], 154 AA 2034 [Aw], 163
AA 413,1 [Ae], 241 AA 1145 [Aw], 154 AA 2036 [Aw] , 163
AA 435.2 [Ae], 242 AA 1150 [Aw], 154 AA 2037 [Aw] , 163
AA 443,0 [Ae] , 242 AA 1160 [Aw], 155 ' AA 2038 [Aw], 163
AA 443.1 [Ae], 242 AA 1165 [Aw], 155 AA 2048 [Aw], 163
AA 443,2 [Ae], 242 AA 1170 [Aw], 155 AA 2053 [Aw], 163
AA 444.0 [Ae], 242 AA 1175 [Aw], 155 AA 2080 [Aw] , 163
AA 444.2 [Ae], 242 AA 1180 [Aw], 155 AA 2090 [Aw], 163
AA 445.2 [Ae], 242 AA 1185 [Aw], 155 AA 2091 [Aw], 163
AA 516,0 [Ae], 243 AA 1187 [Aw], 155 AA 2094 [Aw], 163
AA 516.1 [Ae], 243 AA 1188 [Aw], 155 AA 2095 [Aw], 163
AA 518,0 [Ae], 243 AA 1190 [Aw], 155 AA 2097 [Aw], 163
AA 518,1 [Ae], 243 AA 1193 [Aw], 155 AA 2111 [Aw], 163
AA 518,2 [Ae], 243 AA 1197 [Aw], 155 AA 2117 [Aw], 164
AA 520,0 [Ae], 243 AA 1198 [Aw], 155 AA 2124 [Aw], 164
AA 520,2 [Ae], 243 AA 1199 [Aw], 155 AA 2195 [Aw], 164
AA 535,0 [Ae], 243 AA 1200 [Aw], 156 AA 2197 [Aw], 164
AA 535.2 [Ae], 243 AA 1200A [Aw], 156 AA 2214 [Aw], 164
AA 705.0 [Ae], 244 AA 1230 [Aw], 156 AA 2218 [Aw], 164
AA 705.1 [Ae], 244 AA 1235 [Aw], 156 AA 2219 [Aw], 165
AA 707.0 [Ae], 244 AA 1245 [Aw], 156 AA 2224 [Aw], 165
AA 707.1 [Ae], 244 AA 1250 [Aw], 156 AA 2225 [Aw], 165
AA 710.0 [Ae], 244 AA 1260 [Aw], 157 AA 224,0 [Ae], 234
AA 710.1 [Ae], 244 AA 1270 [Aw], 157 AA 224.2 [Ae], 234
AA 711,0 [Ae], 244 AA 1275 [Aw], 157 AA 2319 [Aw], 165
AA 711.1 [Ae], 244 AA 1285 [Aw], 157 AA 2324 [Aw], 165
AA 712,0 [Ae], 244 AA 130.1 [Ae], 233 AA 2419 [Aw], 165
AA 712,2 [Ae], 244 AA 1330 [Aw], 157 AA 2424 [Aw], 165
AA 7130 [Ae] , 244 AA 1335 [Aw], 157 AA 2519 [Aw], 165
AA 713,1 [Ae] , 244 AA 1345 [Aw], 157 AA 2524 [Aw] , 165
AA 771,0 [Ae], 244 AA 1350 [Aw], 157 AA 2618 [Aw], 165
AA 771,2 [Ae], 245 AA 1350A [Aw], 157 AA2618A[Aw],166
AA 772,0 [Ae] , 245 AA 1360 [Aw], 157 AA [Aw] , 166
3002
AA 772.2 [Ae], 245 AA 1370 [Aw], 157 AA [Aw] , 166
3003
AA 850,0 [Ae], 245 AA 1385 [Aw], 158 AA Alclad [Aw], 167
3003
AA 850.1 [Ae], 245 AA 1435 [Aw] , 158 AA [Aw] , 167
3004
AA 851,0 [Ae], 245 AA 1445 [Aw] , 158 AA 3004 Alclad [Aw], 168
AA 851,1 [Ae], 245 AA 1450 [Aw], 158 AA 3004A [Aw], 168
512 Index of Alloy Names and Designations
AA 3005 [Aw], 168 AA 5005A [Aw], 174 AA 5210 [Aw], 182
AA 3005 Alclad [Aw], 168 AA 5006 [Aw], 174 AA 5249 [Aw], 182
AA 3006 [Aw], 168 AA 5007 [Aw], 174 AA 5250 [Aw], 182
AA 3007 [Aw] , 168 AA 5008 [Aw], 174 AA 5251 [Aw], 182
AA 3008 [Aw] , 168 AA 5009 [Aw], 174 AA 5251A [Aw], 183
AA 3009 [Aw], 168 AA 5010 [Aw], 174 AA 5252 [Aw], 183
AA 3010 [Aw], 168 AA 5011 [Aw], 175 AA 5254 [Aw], 183
AA 3011 [Aw], 168 AA 5013 [Aw], 175 AA 5257 [Aw], 183
AA 3012 [Aw], 168 AA 5014 [Aw], 175 AA 5280 [Aw], 183
AA 3013 [Aw], 169 AA 5016 [Aw], 175 AA 5283 [Aw], 183
AA 3014 [Aw], 169 AA 5017 [Aw], 175 AA 5283A [Aw], 183
AA 3015 [Aw], 169 AA 5018 [Aw], 175 AA 5305 [Aw], 183
AA 3016 [Aw], 169 AA 5019 [Aw], 175 AA 5310 [Aw], 183
AA 3017 [Aw], 169 AA 5021 [Aw], 175 AA 5349 [Aw], 183
AA 3018 [Aw], 169 AA 5022 [Aw], 175 AA 5351 [Aw], 183
AA 3102 [Aw], 169 AA 5023 [Aw], 175 AA 5352 [Aw], 183
AA 3103 [Aw], 169 AA 5034 [Aw], 175 AA 5354 [Aw], 184
AA 3103A [Aw], 169 AA 5039 [Aw], 175 AA 5356 [Aw], 184
AA 3104 [Aw], 169 AA 5040 [Aw], 175 AA 5357 [Aw], 184
AA 3105 [Aw], 170 AA 5042 [Aw], 176 AA 5383 [Aw], 184
AA 3105A [Aw], 170 AA 5043 [Aw], 176 AA 5405 [Aw], 184
AA 3107 [Aw], 170 AA 5049 [Aw], 176 AA 5449 [Aw], 184
AA 3203 [Aw], 170 AA 5050 [Aw], 176 AA 5451 [Aw], 184
AA 3204 [Aw], 170 AA 5050A [Aw], 176 AA 5454 [Aw], 184
AA 3205 [Aw], 170 AA 5050B [Aw], 176 AA 5456 [Aw], 185
AA 3207 [Aw], 170 AA 5051 [Aw], 176 AA 5456A [Aw], 185
AA 3207A [Aw], 170 AA 5051A [Aw], 176 AA 5457 [Aw], 185
AA 3303 [Aw], 170 AA 5052 [Aw], 177 AA 5505 [Aw], 185
AA 3307 [Aw], 170 AA 5053 [Aw], 177 AA 5552 [Aw], 185
AA 4001 [Aw], 171 AA 5056 [Aw], 177 AA 5554 [Aw], 186
AA 4002 [Aw], 171 AA 5056A [Aw], 178 AA 5556 [Aw], 186
AA 4004 [Aw], 171 AA 5058 [Aw], 178 AA 5556A [Aw], 186
AA 4006 [Aw], 171 AA 5082 [Aw], 178 AA 5557 [Aw], 186
AA 4007 [Aw], 171 AA 5083 [Aw], 178 AA 5605 [Aw], 186
AA 4008 [Aw], 171 AA 5086 [Aw], 179 AA 5652 [Aw], 186
AA 4009 [Aw], 171 AA 5087 [Aw], 180 AA 5654 [Aw], 186
AA 4010 [Aw], 171 AA 5091 [Aw], 180 AA 5657 [Aw], 186
AA 4011 [Aw], 171 AA 5105 [Aw], 180 AA 5754 [Aw], 187
AA 4012 [Aw], 172 AA 511.0 [Ac], 242 AA 5757 [Aw], 188
AA 4013 [Aw], 172 AA 511.1 [Ac], 242 AA 5854 [Aw], 188
AA 4014 [Aw], 172 AA 511.2 [Ac], 242 AA 5857 [Aw], 188
AA 4015 [Aw], 172 AA 5110 [Aw], 180 AA 5954 [Aw], 188
AA 4016 [Aw], 172 AA 5119 [Aw], 180 AA 5957 [Aw], 188
AA 4017 [Aw], 172 AA 512.0 [Ac], 242 AA 6001 [Aw], 188
AA 4018 [Aw], 172 AA 512.2 [Ac], 242 AA 6002 [Aw], 188
AA 4032 [Aw], 172 AA 513.0 [Ac], 242 AA 6003 [Aw], 188
AA 4043 [Aw], 172 AA 513.2 [Ac], 242 AA 6004 [Aw], 188
AA 4043A [Aw], 172 AA 514.0 [Ac], 243 AA 6005 [Aw], 188
AA 4044 [Aw], 172 AA 514.1 [Ac], 243 AA 6005A [Aw], 188
AA 4045 [Aw], 172 AA 514.2 [Ac], 243 AA 6005B [Aw], 189
AA 4046 [Aw], 172 AA 5149 [Aw], 180 AA 6006 [Aw], 189
AA 4047 [Aw], 173 AA 515.0 [Ac], 243 AA 6007 [Aw], 189
AA 4047A [Aw], 173 AA 515.2 [Ac], 243 AA 6008 [Aw], 189
AA 4048 [Aw], 173 AA 5150 [Aw], 180 AA 6009 [Aw], 189
AA 4101 [Aw], 173 AA 5151 [Aw], 180 AA 6010 [Aw], 189
AA4104 [Aw], 173 AA 5152 [Aw], 181 AA6011 [Aw], 189
AA 4145 [Aw], 173 AA 5154 [Aw], 181 AA 6012 [Aw], 189
AA 4145A [Aw], 173 AA 5154A [Aw], 181 AA 6013 [Aw], 189
AA 4147 [Aw], 173 AA 5154B [Aw], 181 AA 6014 [Aw] , 189
AA 4245 [Aw], 173 AA 5155 [Aw] , 181 AA 6015 [Aw], 189
AA 4343 [Aw], 173 AA 5180 [Aw] , 181 AA 6016 [Aw], 190
AA 4543 [Aw], 173 AA 5182 [Aw] , 181 AA 6016A [Aw], 190
AA 4643 [Aw], 173 AA 5183 [Aw], 182 AA 6017 [Aw], 190
AA 5004 [Aw], 173 AA 5186 [Aw], 182 AA 6018 [Aw], 190
AA 5005 [Aw], 174 AA 5205 [Aw], 182 AA 6020 [Aw], 190
Index of Alloy Names and Designations 513
AA 6022 [Aw], 190 AA [Aw], 199
7012 AA B001 [Aw], 207
AA 6051 [Aw], 190 AA [Aw], 199
7013 AA B004 [Aw], 207
AA 6053 [Aw], 190 AA [Aw], 199
7014 AA B005 [Aw], 207
AA 6056 [Aw], 190 AA [Aw], 199
7015 AA B006 [Aw], 207
AA 6060 [Aw], 190 AA [Aw], 199
7016 AA B007 [Aw], 207
AA 6061 [Aw], 191 AA [Aw], 200
7017 AA BOOB [Aw], 207
AA 6061A [Aw], 192 AA 701B [Aw], 200 AA B009 [Aw], 207
AA 6062 [Aw], 192 AA 7019 [Aw], 200 AA BOlO [Aw], 207
AA 6063 [Aw], 193 AA 7019A [Aw], 200 AA BOll [Aw], 207
AA 6063A [Aw], 193 AA 7020 [Aw], 200 AA B011A [Aw], 207
AA 6066 [Aw], 193 AA 7021 [Aw], 200 AA B013 [Aw], 208
AA 6069 [Aw], 193 AA 7022 [Aw], 201 AA B014 [Aw], 208
AA 6070 [Aw], 193 AA 7023 [Aw], 201 AA B015 [Aw], 208
AA 6071 [Aw], 194 AA 7024 [Aw], 201 AA B016 [Aw], 208
AA 6081 [Aw], 194 AA 7025 [Aw], 201 AA 8017 [Aw], 208
AA 6082 [Aw], 194 AA 7026 [Aw], 201 AA 801B [Aw], 208
AA 6082A [Aw], 195 AA 7027 [Aw], 201 AA 8019 [Aw], 208
AA 6090 [Aw], 195 AA 702B [Aw], 201 AA B020 [Aw], 208
AA 6091 [Aw], 195 AA 7029 [Aw], 201 AA B021 [Aw], 208
AA 6092 [Aw], 195 AA 7030 [Aw], 201 AA 8021A [Aw], 208
AA 6101 [Aw], 196 AA 7031 [Aw], 201 AA 8021 B [Aw], 208
AA 6101A [Aw], 196 AA 7032 [Aw], 201 AA B022 [Aw], 208
AA 6101B [Aw], 196 AA 7033 [Aw], 201 AA B030 [Aw], 208
AA 6103 [Aw], 196 AA 7039 [Aw], 201 AA B040 [Aw], 208
AA 6105 [Aw], 196 AA 7040 [Aw], 201 AA B050 [Aw], 208
AA 6106 [Aw], 196 AA 7046 [Aw], 202 AA 8076 [Aw], 208
AA 6110 [Aw], 196 AA 7049 [Aw], 202 AA B077 [Aw], 208
AA6110A[Aw], 196 AA 7049A [Aw], 202 AA 8079 [Aw], 209
AA 6111 [Aw], 196 AA 7050 [Aw], 202 AA BOB1 [Aw], 209
AA 6113 [Aw], 197 AA 7050A [Aw], 202 AA B090 [Aw], 209
AA 6116 [Aw], 197 AA 7051 [Aw], 202 AA 8091 [Aw], 209
AA6151 [Aw], 197 AA 7055 [Aw], 203 AA B093 [Aw], 209
AA 6160 [Aw], 197 AA 7060 [Aw], 203 AA 8111 [Aw], 209
AA 6162 [Aw], 197 AA 7064 [Aw], 203 AA 8112 [Aw], 209
AA 6181 [Aw], 197 AA 7070 [Aw], 203 AA B130 [Aw], 209
AA 6201 [Aw], 197 AA 7072 [Aw], 203 AA B176 [Aw], 209
AA 6201A [Aw], 197 AA 7075 [Aw], 203 AABl77 [Aw], 209
AA 6205 [Aw], 197 AA 7075 Alclad [Aw], 204 AA 8211 [Aw], 209
AA 6206 [Aw], 197 AA 7076 [Aw], 204 AA B212 [Aw], 209
AA 6253 [Aw], 197 AA 7079 [Aw], 204, 205 AA B276 [Aw], 209
AA 6261 [Aw], 197 AA 7090 [Aw], 205 AA B2BO [Aw], 209
AA 6262 [Aw], 197 AA 7091 [Aw], 205 AA A201 ,0 [Ae], 261
AA 6301 [Aw], 198 AA 7093 [Aw], 205 AA A201, 1 [Ae], 261
AA 6306 [Aw], 198 AA 7104 [Aw], 205 AA A206,0 [Ae], 261
AA 6351 [Aw], 198 AA 7108 [Aw], 205 AA A206,2 [Ae], 261
AA 6351A [Aw], 198 AA 710BA [Aw], 205 AA A242,0 [Ae], 261
AA 6363 [Aw], 198 AA 7109 [Aw], 205 AA A242, 1 [Ae], 261
AA 6401 [Aw], 198 AA 7116 [Aw], 205 AA A242,2 [Ae], 261
AA 6463 [Aw], 198 AA 7129 [Aw], 205 AA A305,0 [Ae], 261
AA 6463A [Aw], 198 AA 7139 [Aw], 205 AA A305, 1 [Ae], 261
AA 6563 [Aw], 198 AA 7146 [Aw], 205 AA A305,2 [Ae] , 261
AA [Aw],
6663 198 AA 7149 [Aw], 205 AAA319,0 [Ae], 262
AA [Aw],
6763 198 AA 7150 [Aw], 205 AAA319,1 [Ae], 262
AA [Aw],
6863 198 AA 7175 [Aw], 205 AA A333,0 [Ae], 262
AA [Aw],
6951 198 AA 717B [Aw], 206 AA A333, 1 [Ae], 262
AA [Aw],
6963 199 AA 7179 [Aw], 206 AA A355,0 [Ae], 262
AA [Aw],
7001 199 AA 7229 [Aw], 206 AA A355,2 [Ae], 262
AA [Aw],
7002 199 AA 7249 [Aw], 206 AA A356,0 [Ae], 262
AA [Aw],
7003 199 AA 7277 [Aw], 206 AA A356, 1 [Ae], 262
AA [Aw],
7004 199 AA 7278 [Aw], 206 AA A356,2 [Ae], 262
AA [Aw],
7005 199 AA 727BA [Aw], 206 AA A357,0 [Ae], 262
AA 700B
[Aw], 199 AA 7349 [Aw], 206 AA A357,2 [Ae], 262
AA [Aw],
7009 199 AA 7449 [Aw], 206 AA A359,0 [Ae], 262
AA 7010 [Aw], 199 AA 7472 [Aw], 206 AA A359, 1 [Ae], 262
AA 7011 [Aw], 199 AA 7475 [Aw], 206 AA A360,0 [Ae], 262
514 Index of Alloy Names and Designations
AA A360.1 [Ac] , 263 AA X4005 [Aw], 229 AC5A (casting) (JIS) [Ac] , 266
AA A360.2 [Ac] , 263 AA X5002 [Aw], 229 AC5A.1 (JIS) [Ac], 266
AA A380.0 [Ac] , 263 AAX5012 [Aw], 229 AC5A.2 (ingot) (JIS) [Ac] , 266
AA A380 1 [Ac] , 263 AA X5015 [Aw], 229 AC7A (casting) (JIS) [Ac], 267
AA A380.2 [Ac] , 263 AA X5020 [Aw], 230 AC7A.1 (JIS) [Ac] , 267
AA A383.0 [Ac], 263 AA X5055 [Aw], 230 AC7A.2 (ingot) (JIS) [Ac] , 267
AA A383.1 [Ac] , 263 AA X5058 [Aw], 230 AC8A (casting) (JIS) [Ac], 267
AA A384.0 [Ac], 263 AA X5080 [Aw], 230 AC8A.1 (JIS) [Ac], 267
AA A384.1 [Ac], 263 AA X5084 [Aw], 230 AC8A.2 (ingot) (JIS) [Ac], 267
AA A390.0 [Ac], 263 AA X5090 [Aw], 230 AC88 (casting) (JIS) [Ac] , 267
AA A390.1 [Ac], 263 AA X5153 [Aw], 230 AC88.1 (JIS) [Ac], 267
AAA413.0 [Ac], 263 AAX5184 [Aw], 230 AC8B.2 (ingot) (JIS) [Ac], 267
AA A413.1 [Ac] , 263 AA X5452 [Aw], 230 AC8C (casting) (JIS) [Ac], 267
AA A413.2 [Ac], 263 AA X6030 [Aw], 230 AC8C.1 (JIS) [Ac]. 267
AA A443.0 [Ac] , 264 AA X6064 [Aw], 230 AC8C.2 (ingot) (JIS) [Ac], 267
AA A443.1 [Ac], 264 AA X6067 [Aw], 230 AC9A (casting) (JIS) [Ac], 267
AA A444.0 [Ac], 264 AAX6161 [Aw], 230 AC9A.1 (JIS) [Ac], 267
AAA444.1 [Ac] , 264 AAX6163 [Aw], 230 AC9A.2 (ingot) (JIS) [Ac]. 267
AA A444.2 [Ac], 264 AA X6251 [Aw], 230 AC98 (casting) (JIS) [Ac], 268
AA A535.0 [Ac], 264 AA X7006 [Aw], 230 AC98.1 (JIS) [Ac], 268
AA A535.1 [Ac], 264 AA X7007 [Aw], 230 AC98.2 (ingot) (JIS) [Ac], 268
AA 8201.1 [Ac], 276 AA X7038 [Aw], 230 AD1.1 (JIS) [Ac], 268
AA 8319.0 [Ac], 276 AA X7040 [Aw], 231 AD1.2 (ingot) (JIS) [Ac], 268
AA 8319.1 [Ac], 276 AA X7080 [Aw], 231 AD10.1 (JIS) [Ac], 268
AA 8356.0 [Ac], 276 AA X71 06 [Aw], 231 AD1 0.2 (ingot) (JIS) [Ac] , 268
AA 8356.2 [Ac], 276 AA X7272 [Aw], 231 AD10Z.1 (JIS) [Ac], 268
AA 8357.0 [Ac] , 276 AA X7275 [Aw], 231 AD12.1 (LME) (JIS) [Ac]. 269
AA 8357.2 [Ac], 276 AA X7279 [Aw], 231 AD12.2 (ingot) (JIS) [Ac], 269
AA 8380.0 [Ac], 276 AA X8002 [Aw], 231 AD12Z.1 (JIS) [Ac], 269
AA 8380.1 [Ac], 276 AA X8003 [Aw], 231 AD14.1 (JIS) [Ac], 269
AA 8384.0 [Ac] , 276 AA X8090A [Aw], 231 AD14.2 (ingot) (JIS) [Ac], 269
AA 8384.1 [Ac], 276 AA X8092 [Aw], 231 AD3.1 (JIS) [Ac], 268
AA 8390.0 [Ac], 276 AA X8192 [Aw], 231 AD3.2 (ingot) (JIS) [Ac], 268
AA 8390.1 [Ac], 276 AA X8380 [Aw], 231 AD5.1 (JIS) [Ac], 268
AA 8413.0 [Ac], 277 AA X8480 [Aw], 231 AD5.2 (ingot) (JIS) [Ac], 268
AA 8413.1 [Ac] , 277 AC1A (casting) (JIS) [Ac] , 264 AD6.1 (JIS) [Ac] , 268
AA 8443.0 [Ac] , 277 AC1A.1 (JIS) [Ac] , 264 AD6.2 (ingot) (JIS) [Ac], 268
AA 8443.1 [Ac], 277 AC1A.2 (ingot) (JIS) [Ac], 264 ADC1 (casting) (JIS) [Ac] , 269
AA 8535.0 [Ac], 277 AC1 B (casting) (JIS) [Ac], 265 ADC10 (casting) (JIS) [Ac], 269
AA 8535.2 [Ac], 277 AC1 8.1 (JIS) [Ac], 265 ADC10Z (casting) (JIS) [Ac] , 269
AA C355.0 [Ac], 277 AC1 8.2 (ingot) (JIS) [Ac], 265 ADC12 (casting) (JIS) [Ac], 269
AA C355.1 [Ac] , 277 AC2A (casting) (JIS) [Ac] , 265 ADC12Z (casting) (JIS) [Ac] , 269
AA C355.2 [Ac], 277 AC2A.1 (JIS) [Ac], 265 ADC14 (casting) (JIS) [Ac], 269, 270
AA C356.0 [Ac], 277 AC2A.2 (ingot) (JIS) [Ac], 265 ADC3 (casting) (JIS) [Ac], 269
AA C356.2 [Ac], 277 AC2B (casting) (JIS) [Ac], 265 ADC5 (casting) (JIS) [Ac], 269
AA C357.0 [Ac], 277 AC28.1 (JIS) [Ac] , 265 ADC6 (casting) (JIS) [Ac], 269
AA C357.2 [Ac] , 277 AC28.2 (ingot) (JIS) [Ac], 265 AE42 (Hydro Magnesium) [Mc] , 298
AA C380.0 [Ac], 277 AC3A (casting) (JIS) [Ac], 265 AE42 (Magnesium Elektron) [Mc] , 298
AA C380.1 [Ac], 277 AC3A.1 (JIS) [Ac], 265 AE42X1 (Dow Magnesium) [Mc] , 298
AA C384.0 [Ac], 278 AC3A.2 (ingot) (JIS) [Ac], 265 AECMA MG-C-43 [Mc] , 311
AA C384.1[Ac], 278 AC4A (casting) (JIS) [Ac], 265 AECMA MG-C-51 [Mc]. 311
AA C443.0[Ac], 278 AC4A.1 (JIS) [Ac], 265 AECMA MG-C-61 [Mc] , 311
AA C443.1[Ac], 278 AC4A.2 (ingot) (JIS) [Ac], 265 AECMA MG-C-91 [Mc] , 311
AA C443.2[Ac], 278 AC48 (casting) (JIS) [Ac], 266 AECMA MG-P-43 [Mw] , 311
AA D355.2[Ac], 281 AC48.1 (JIS) [Ac], 266 AECMA MG-P-63 [Mw] , 311
AA D357.0[Ac], 281 AC4B.2 (ingot) (JIS) [Ac], 266 AECMA Ti P62 [Tw], 340
AA D380.0[Ac], 281 AC4C (casting) (JIS) [Ac], 266 AECMA Ti P9001 [Tw], 340
AA D380.1 [Ac], 282 AC4C.1 (JIS) [Ac], 266 Aerospace Metal Composites AMC217xe
AA F356.0 [AC] , 282 AC4C.2 (ingot) (JIS) [Ac], 266 [Aw] , 215
AA F356.2 [Ac] , 282 AC4CH (casting) (JIS) [Ac] , 266 Aerospace Metal Composites AMC225xe
[Aw],215
AA X2096 [Aw], 229 AC4CH.1 (JIS) [Ac], 266
Aerospace Metal Composites AMC225xh
AA X2119 [Aw], 229 AC4CH.2 (ingot) (JIS) [Ac], 266
[Aw],215
AA X2316 [Aw], 229 AC4D (casting) (JIS) [Ac], 266
Aerospace Metal Composites AMC235xe
AA X3030 [Aw], 229 AC4D.1 (JIS) [Ac], 266 [Aw],215
AA X4003 [Aw], 229 AC4D.2 (ingot) (JIS) [Ac], 266
Index of Alloy Names and Designations 515
Aerospace Metal Composites AMC500sa AI 25 (GOST) [Ac], 272 AI-Si5Fe (ISO) [Ac], 274
[Aw],215 AI 27 (GOST) [Ac] , 272 AI-Si5Mg (ISO) [Ac], 274
Aerospace Metal Composites AMC640xa AI 27-1 (GOST) [Ac], 272 AI-Si10Mg (ISO) [Ac], 275
[Aw],215
AI 28 (GOST) [Ac] , 272 AI-Si6Cu4 (ISO) [Ac], 275
Affimet A-Z1 OS8G [Ac] , 261
AI 29 (GOST) [Ac], 272 AI-Si6Cu4Fe (ISO) [Ac], 275
Affimet Calypso 25M [Ac] , 278
AI 3 (GOST) [Ac], 271 AI-Si7Mg (ISO) [Ac], 275
Affimet Calypso 41 R [Ac] , 278
AI 30 (GOST) [Ac] , 272 AI-Si7Mg(Fe) (ISO) [Ac] , 275
Affimet Calypso 43B [Ac] , 278
AI 32 (GOST) [Ac] , 272 AI-Si8Cu3Fe (ISO) [Ac], 275
Affimet Calypso 43X [Ac], 278
AI 33 (GOST) [Ac], 272 AI-Si12 (ISO) [Ac] , 275
Affimet Calypso 49R [Ac], 278
AI 34 (GOST) [Ac] , 272 AI-Si12Cu (ISO) [Ac] , 275
Affimet Calypso 61S [Ac] , 279
AI 4 (GOST) [Ac] , 271 AI-Si12CuFe (ISO) [Ac] , 275
Affimet Calypso 67B [Ac] , 279
AI 4-1 (GOST) [Ac] , 271 AI-Si12Fe (ISO) [Ac], 275
Affimet Calypso 67B1 [Ac], 279 AI 5 (GOST) [Ac], 271 AI Sr 3.5 (Aleastur) [Ac], 273
Affimet Calypso 67N [Ac], 279
AI 5-1 (GOST) [Ac], 271 AI Sr 5 (Aleastur) [Ac], 273
Affimet Calypso 67N1 [Ac], 279
AI 6 (GOST) [Ac], 271 AI/Sr 5 (GM Metal) [Ac] , 275
Affimet Calypso 67R [Ac], 279
AI 7 (GOST) [Ac], 271 AI/Sr 10 (GM Metal) [Ac] , 275
Affimet Calypso 67R1 [Ac], 279 AI 8 (GOST) [Ac], 271 AI Sr 10 (Aleastur) [Ac], 273
Affimet Calypso 67R2 [Ac], 280
AI 9 (GOST) [Ac], 271 AI Sr Ti B 10/1/0.2 (Aleastur) [Ac], 273
Affimet Calypso 67S [Ac], 280
AI 9-1 (GOST) [Ac] , 271 AI Sr10 Ca3 (GM Metal) [Ac], 273
Affimet Calypso 67S2 [Ac] , 280
AI 99 (DIN) [Aw], 210 AI Ti 10 (Aleastur) [Ac], 273
Affimet Calypso 67XB [Ac], 280
AI 99.5 (DIN) [Aw], 210 AI Ti 5 (Aleastur) [Ac], 273
Affimet Calypso 67XB1 [Ac] , 280
AI99.5TiO.6 (DIN) [Aw], 210 AI Ti 6 (Aleastur) [Ac], 273
Affimet Calypso 67XR [Ac], 280
AI 99.7 (DIN) [Aw], 210 AI Ti B 3/0.2 (Aleastur) [Ac], 273
Affimet Calypso 67XR1 [Ac], 280
AI 99.8 (DIN) [Aw], 210 AI Ti B 3/1 (Aleastur) [Ac], 273
Affimet Calypso 69B [Ac], 280
AI 99.8 MgO.5 (DIN) [Aw], 210 AI Ti B 5/0.2 (Aleastur) [Ac], 273
Affimet Calypso 69R [Ac], 280
AI 99.85 (DIN) [Aw], 211 AI Ti B 5/0.6 (Aleastur) [Ac] , 273
Affimet Calypso 69R2 [Ac] , 281
AI 99.85 Mg Si (DIN) [Aw], 211 AI Ti B 5/1 (Aleastur) [Ac], 273
Affimet Calypso 69S [Ac], 281
AI 99.85 Mg SiOA (DIN) [Aw], 211 AI Ti B 6/0A (Aleastur) [Ac], 274
Affimet Calypso 82P1 [Ac], 281
AI 99.85 Mg1 (DIN) [Aw], 211 AI Zn4.5 MgO.8 (DIN) [Aw], 214
Affimet Calypso 85R [Ac], 281
AI 99.9 (DIN) [Aw], 211 AI Zn4.5 Mg1 (DIN) [Aw] , 214
Affimet Calypso 87P [Ac] , 281
AI 99.9 Mg Si (DIN) [Aw], 211 AI-Zn5Mg (ISO) [Ac], 275
Affimet Calypso 92A [Ac], 281
AI 99.9 MgO.5 (DIN) [Aw], 211 AI Zr 10 (Aleastur) [Ac], 274
AG 3 (NF) [Ac] , 270
AI 99.9 Mg1 (DIN) [Aw], 211 AI Zr 5 (Aleastur) [Ac], 274
AG.10 (GM Metal) [Ac] , 270
AI 99.95 MgO.5 (DIN) [Aw], 211 AlbeMet AM162 (Brush Wellman) [8w], 345
AG.20 (GM Metal) [Ac], 270
AI B 3 (Aleastur) [Ac], 272 AlbeMet AM162 Extruded Bar (Brush
AG.25 (GM Metal) [Ac] , 270 Wellman) [8w], 345
AI B 4 (Aleastur) [Ac], 272
A-G 10 (NF) [Ac], 255 AlbeMet AM162 Rolled Sheet (Brush
AI B 5 (Aleastur) [Ac], 272
A-G10S Y4 (NF) [Ac], 255 Wellman) [Bw], 345
AI Ca (Aleastur) [Ac], 272
A-G1 OSBe (NF) [Ac], 255 AlbeMet AM162H (Brush Wellman) [Bw],
AI Cu (Aleastur) [Ac], 272
A-G3 (NF) [Aw], 210 345
AI-Cu4MgTi (ISO) [Ac], 274
A-G3T (NF) [Ac], 255 Aleastur AI B 3 [Ac], 272
AI-Cu4Ni2Mg2 (ISO) [Ac], 274
A-G4MC (NF) [Aw], 210 Aleastur AI B 4 [Ac], 272
AI-Cu4Ti (ISO) [Ac], 274
A-G4Z (NF) [Ac], 255 Aleastur AI B 5 [Ac], 272
AIFeMg (DIN) [Aw], 212
AG5S (NF) [Ac], 270 Aleastur AI Ca [Ac], 272
AI Mg SiO.3 (DIN) [Aw], 212
A-G6 (NF) [Ac], 255 Aleastur AI Cu [Ac], 272
AI Mg SiO.5 (DIN) [Aw], 212
A-G6Y4 (NF) [Ac], 256 Aleastur AI Si [Ac], 273
AI Mg SiO.? (DIN) [Aw], 213
AGS (NF) [Aw], 210 Aleastur AI Sr 10 [Ac], 273
AI Mg SiO.8 (DIN) [Aw], 213
AK21M2.5N2.5 (GOST) [Ac], 270 Aleastur AI Sr 3.5 [Ac] , 273
AI Mg Si1 (DIN) [Aw], 213
AK4M2116 (AI17B) (GOST) [Ac], 270 Aleastur AI Sr 5 [Ac], 273
AI MgO.5 (DIN) [Aw], 212
AK4M4 (AI15B) (GOST) [Ac], 270 Aleastur AI Sr Ti B 10/1/0.2 [Ac], 273
AI Mg1 (DIN) [Aw], 212
AK5M2 (AI3B) (GOST) [Ac], 270 Aleastu r AI Ti 10 [Ac], 273
AI Mg1.8 (DIN) [Aw], 212
AK5M7 (AI1 OB) (GOST) [Ac], 270 Aleastur AI Ti 5 [Ac], 273
AI Mg3 EO (DIN) [Aw], 212
AK7 (AI9B) (GOST) [Ac], 270 Aleastur AI Ti 6 [Ac], 273
AI-Mg3 (ISO) [Ac], 274
AK7M2 (AI14B) (GOST) [Ac], 270 Aleastur AI Ti B 3/0.2 [Ac], 273
AIMg3.5 (DIN) [Aw], 212
AK9 (AI4B) (GOST) [Ac], 270 Aleastur AI Ti B 3/1 [Ac], 273
AI-Mg3Si2 (ISO) [Ac], 274
AI 1 (GOST) [Ac] , 270 Aleastur AI Ti B 5/0.2 [Ac], 273
AI-Mg6 (ISO) [Ac], 274
AI 11 (GOST) [Ac], 271 Aleastur AI Ti B 5/0.6 [Ac], 273
AI-Mg5Si1 (ISO) [Ac], 274
AI 13 (GOST) [Ac], 271 Aleastur AI Ti B 5/1 [Ac], 273
AI-Mg10 (ISO) [Ac], 274
AI 19 (GOST) [Ac], 271 Aleastur AI Ti B 6/0A [Ac], 274
AI Mn Cu (DIN) [Aw], 213
AI 2 (GOST) [Ac], 271 Aleastur AI Zr 10 [Ac], 274
AI Mn1 (DIN) [Aw], 213
AI21 (GOST) [Ac] , 271 Aleastur AI Zr 5 [Ac], 274
AI/Sb 10 (GM Metal) [Ac], 274
AI22 (GOST) [Ac] , 271 Allvac 30 (Teledyne) [Tw], 329
AI Si (Aleastur) [Ac], 273
AI 23 (GOST) [Ac], 271 Allvac 3-2.5 (Teledyne) [Tw], 328
AI-Si5 (ISO) [Ac], 274
AI 23-1 (GOST) [Ac], 272 Allvac 40 (Teledyne) [Tw], 329
AI-Si5Cu1 Mg (ISO) [Ac] , 274
AI 24 (GOST) [Ac], 272 Allvac 40+Pd (Teledyne) [Tw], 329
AI-Si5Cu3 (ISO) [Ac], 274
Allvac 50 (Teledyne) [Tw], 329
516 Index of Alloy Names and Designations
Allvac 5-2.5 (Teledyne) [Tw], 328 Alusuisse Anticorodal 110 [Aw], 217 AM20 (Hydro Magnesium) [Me], 298
Allvac 55 (Teledyne) [Tw], 329 Alusuisse Anticorodal112 [Aw], 217 AM50A (ASTM) [Me), 298
Allvac 6-2-4-2 (Teledyne) [Tw], 328 Alusuisse Anticorodal114 [Aw], 217 AM50B (ASTM) [Me), 298
Allvac 6-2-4-6 (Teledyne) [Tw], 329 Alusuisse Anticorodal120 [Aw], 217 AM60 (ASTM) [Mc), 299
Allvac 6-4 (Teledyne) [Tw], 329 Alusuisse Anticorodal Pb-107 [Aw], 217 AM60A (ASTM) [Me], 299
Allvac 6-4 ELI (Teledyne) [Tw], 329 Alusuisse Anticorodal Pb-109 [Aw), 217 AM60B (ASTM) [Me), 299
Allvac 6-6-2 (Teledyne) [Tw], 329 Alusuisse Avional100 [Aw), 218 AM60SX (Timminco) [Me), 299
Allvac 6-7 (Teledyne) [Tw), 329 Alusuisse Avional-1 02 [Aw), 218 AM60X (Timminco) [Me], 299
Allvac 70 (Teledyne) [Tw], 329 Alusuisse Avional 150 [Aw), 219 AM62 (BaAL UK) [Aw), 214
Allvac 8-1-1 (Teledyne) [Tw], 329 Alusuisse AVlonal 152 [Aw), 219 AM65 (BOAl UK) [Aw], 214
Alplan (Alusuisse) [Aw], 213 Alusuisse Avional-660 [Aw], 219 AM68 (BaAL UK) [Aw), 215
ALPOCa Aluminium Needles (1) [Ap], 295 Aiusuisse Avional-662 [Aw], 219 AM80 (Timminco) [Me), 299
ALPOCa Aluminium Needles (2) [Ap), 295 Alusuisse Avional Pb-118 [Aw), 219 AM100A (ASTM) [Me), 298
ALPOCa Atomised AI 97% [Ap], 295 Alusuisse Certal [Aw], 220 AMAG Titanal [Aw), 228
ALPOCa Atomised AI 99.7% [Ap) 295 Alusuisse Contal [Aw), 220 AMC217xe (Aerospace Metal Composites)
ALPOCa Atomised AI 99.9% [Ap), 296 Alusuisse Decoltal 500 [Aw), 220 [Aw].215
ALPOCa Atomised AI 99.97% [Ap), 296 Alusuisse Extrudal-043 [Aw], 221 AMC225xe (Aerospace Metal Composites)
ALPOCa Atomised AI 99.99% [Ap], 296 Alusuisse Extrudal-050 [Aw], 221 [Aw),215
ALPOCa Commercial Purity [Ap], 296 Alusuisse Peraluman-050 [Aw), 223 AMC225xh (Aerospace Metal Composites)
[Aw),215
ALPOCa Secondary Purity [Ap), 296 Alusuisse Peraluman-1 00 [Aw), 223
AMC235xe (Aerospace Metal Composites)
ALPOCa Super Pure [Ap), 296 Alusuisse Peraluman-101 [Aw), 223 [Aw),215
Aluman 100 (Alusuisse) [Aw], 213 Alusuisse Peraluman 150 [Aw], 223 AMC500sa (Aerospace Metal Composites)
Alumec 79 (British Aluminium) [Aw), 214 Alusuisse Peraluman 151 [Aw), 223 [Aw) 215
Alumec 89 (British Aluminium) [Aw), 214 Alusuisse Peraluman 253 [Aw), 224 AMC640xa (Aerospace Metal Composites)
Aluminium Needles (1) (ALPOCa) [Ap], 295 Alusuisse Peraluman-226 [Aw), 223 [Aw),215
Aluminium Needles (2) (ALPOCa) [Ap], 295 Alusuisse Peraluman-260 [Aw), 224 AMS 4905 [Tw), 326
Alunord 1370-70 [Aw), 158 Alusuisse Peraluman-300 [Aw), 224 AMS 4907 [Tw), 327
Alunord 6005A [Aw), 188 Alusuisse Peraluman-301 [Aw), 224 AMS 4909 [Tw), 327
Alunord 6060.48 [Aw), 191 Alusuisse Peraluman-302 [Aw), 224 AMS 4910 [Tw), 327
Alunord 6060.79 [Aw], 191 Alusuisse Peraluman-410 [Aw], 224 AMS 4915 [Tw), 327
Alunord 6081-11 [Aw), 194 Alusuisse Peraluman-412 [Aw], 224 AMS 4918 [Tw), 327
Alunord 6082-50 [Aw), 195 Alusuisse Peraluman-460 [Aw), 225 AMS 4919 [Tw), 327
Alunord 6106 [Aw), 196 Alusuisse Peraluman-462 [Aw), 225 AMS 4924 [Tw), 327
Alunord C 50S [Aw), 220 Alusuisse Peraluman-470 [Aw), 225 AMS 4926 [Tw), 328
Alusingen 111 [Aw), 149 Alusuisse Peraluman-502 [Aw), 225 AMS 4974 [Tw], 328
Alusingen 119 [Aw), 149 Alusuisse Peraluman-708 [Aw), 225 AN50 (Otto Fuchs) [Aw), 215
Alusingen 134 [Aw), 149 Alusuisse Peraluman-843 [Aw), 225 Anticorodal-041 (Alusuisse) [Aw), 215
Alusingen 183 [Aw), 150 Alusuisse Peraluman-845 [Aw), 225 Anticorodal 045 (Alusuisse) [Aw), 216
Alusingen 184 [Aw], 150 Alusuisse Peraluman-853 [Aw), 225 Anticorodal 050 (Alusuisse) [Aw), 216
Alusingen 205 [Aw), 150 Alusuisse Peraluman-860 [Aw), 225 Anticorodal 053 (Alusuisse) [Aw), 216
Alusingen 214 [Aw), 150 Alusuisse Peraluman-863 [Aw), 225 Anticorodal 062 (Alusuisse) [Aw), 216
Alusingen 234 [Aw]. 150 Alusuisse Peraluman-875 [Aw), 226 Anticorodal 080 (Alusuisse) [Aw], 216
Alusingen 276 [Aw), 150 Alusuisse Perunal 205 [Aw), 226 Anticorodal-082 (Alusuisse) [Aw], 216
Alusingen 277 [Aw), 150 Alusuisse Perunal215 [Aw), 226 Anticorodal-100 (Alusuisse) [Aw], 216
Alusingen 278 [Aw], 150 Alusuisse Perunal 232 [Aw], 226 Anticorodal-105 (Alusuisse) [Aw], 216
Alusingen 281 [Aw], 150 Alusuisse Perunal 249 [Aw), 226 Anticorodal110 (Alusuisse) [Aw), 217
Alusingen 282 [Aw]. 150 Alusuisse Pure Aluminium 99.0 [Aw), 226 Anticorodal112 (Alusuisse) [Aw), 217
Alusingen 285 [Aw], 150 Alusuisse Pure Aluminium 99.5 [Aw), 227 Anticorodal114 (Alusuisse) [Aw), 217
Alusingen 286 [Aw], 150 Alusuisse Pure Aluminium 99.5 E [Aw), 227 Anticorodal120 (Alusuisse) [Aw], 217
Alusingen 288 [Aw], 150 Alusuisse Pure Aluminium 99.8 [Aw], 227 Anticorodal Pb-107 (Alusuisse) [Aw), 217
Alusingen 289 [Aw], 150 Alusuisse Pure Aluminium 99.85 [Aw), 227 Anticorodal Pb-109 (Alusuisse) [Aw), 217
Alusingen 294 [Aw], 151 Alusuisse Pure Aluminium 99.9 [Aw), 227 ARALL 2 (Structural Laminates Co) [Aw],
Alusuisse Reflectal-050 [Aw), 227 217
Alusingen 297 [Aw], 151
Alustar (Hoogovens) [Aw], 214 Alusuisse Reflectal-100 [Aw), 227 ARALl 3 (Structural laminates Co) [Aw],
217
Alusuisse Alplan [Aw], 213 Alusuisse Relital [Aw], 227
AS AA 150 [Ac], 264
Alusuisse Aluman 100 [Aw], 213 Alusuisse Remiral-050 [Aw], 228
AS AA160 [Ae], 264
Alusuisse Anticorodal-041 [Aw], 215 Alusuisse Remiral-100 [Aw), 228
AS AA170 [Ac], 264
Alusuisse Anticorodal 045 [Aw], 216 Alusuisse Unidal [Aw), 228
AS AA175 [Ac), 264
Alusuisse Anticorodal 050 [Aw], 216 Alusuisse Unidur 091 [Aw], 229
AS AA180 [Ac), 264
Alusuisse Anticorodal 053 [Aw], 216 Alusuisse Unidur 102 [Aw], 229
AS AA 185 [Ac], 264
Alusuisse Anticorodal 062 [Aw], 216 Alusuisse Unidur 120 [Aw), 229
AS BA170 [Ac), 277
Alusuisse Anticorodal 080 [Aw], 216 A-M4 (NF) [Ae), 256
A-SGO.5 (NF) [Aw], 218
Alusuisse Anticorodal-082 [Aw], 216 AM05 (Otto Fuchs) [Aw], 214
A-SGMO.7 (NF) [Aw], 218
Alusuisse Anticorodal-1 00 [Aw], 216 AM11 (Otto Fuchs) [Aw), 214
A-S2GT (NF) [Ac], 256
Alusuisse Anticorodal-1 05 [Aw], 216 AM20 (ASTM) [Me), 298
Index of Alloy Names and Designations 517
A-S2U (NF) [Ae], 256 ASTM AZS1A [Me], 302 Avional100 (Alusuisse) [Aw], 218
A-S4G (NF) [Ae], 256 ASTM AZ91 A [Me], 303 Avional-102 (Alusuisse) [Aw], 218
A-S5U3 (NF) [Ae], 256 ASTM AZ91 B [Me], 303 Avional 150 (Alusuisse) [Aw], 219
A-S5U3G (NF) [Ae], 256 ASTM AZ91 C [Me], 303 Avional152 (Alusuisse) [Aw], 219
A-S5UZ (NF) [Ae], 256 ASTM AZ91 0 [Me], 303 Avional-660 (Alusuisse) [Aw], 219
A-S7G (NF) [Ae], 257 ASTM AZ91 E [Me], 303 Avional-662 (Alusuisse) [Aw], 219
A-S7G03 (NF) [Ae] , 257 ASTM AZ92A [Me], 304 Avional Pb-11S (Alusuisse) [Aw], 219
A-S7G06 (NF) [Ae] , 257 ASTM EQ21A [Me], 305 Ayrton & Partners Pure Magnesium Ingot
A-S7U3G (NF) [Ae] , 257 ASTM EZ33A [Me], 306 [Me],312
A-S9 Y4 (NF) [Ae], 257 ASTM F7 [Tw], 331 Ayrton & Partners Pure Magnesium T-bars
[Me],312
A-S9G (NF) [Ae], 257 ASTM Grade 1 [Tw], 332
A-Z5G (NF) [Ae], 261
A-S9GU (NF) [Ae], 257 ASTM Grade 2 [Tw], 332
AZ10A (ASTM) [Mw], 300
A-S9KG (NF) [Ae] , 258 ASTM Grade 3 [Tw], 332
A-Z10SSG (Affimet) [Ae], 261
A-S9U3 (NF) [Ae] , 258 ASTM Grade 4 [Tew], 333
AZ21X1 (ASTM) [Mw] , 300
A-S9U3 Y4 (NF) [Ae], 258 ASTM Grade 4 [Tw], 332
AZ24 (Otto Fuchs) [Aw], 219
A-S9U3Z Y4 (NF) [Ae], 258 ASTM Grade 5 [Tw], 333
AZ31 (Magnesium Elektron) [Mw] , 300
A-S10G (NF) [Ae], 258 ASTM Grade 6 [TwJ, 333
AZ31 (Timminco) [Mew], 301
A-S10G/R (NF) [Ae], 258 ASTM Grade 7 [TwJ, 333
A-S10UG (NF) [Ae], 258 AZ31B (ASTM) [Mw], 301
ASTM Grade 9 [TwJ, 333
A-S 11 UNG (NF) [Ae], 258 AZ31B (Comeca) [Mw], 301
ASTM Grade 11 [Tw], 333
AZ31B TP (Comeca) [Mw] , 301
A-S12 (NF) [Ae] , 258 ASTM Grade 12 [Tew], 334
AZ31C (ASTM) [Mw] , 301
A-S12 Y4 (NF) [Ae], 259 ASTM Grade 23 [Tw], 334
A-S12N2G (NF) [Ae], 259 AZ34 (Otto Fuchs) [Aw], 219
ASTM HK31A [Mew], 307
A-S 12U (NF) [Ae], 259 AZ61 (Magnesium Elecktron) [Mw], 301
ASTM HM21A [Mw] , 307
A-S12UN (NF) [Ae], 259 AZ61A (ASTM) [Mw], 301
ASTM HM31A [Mw] , 307
A-S12UNG (NF) [Ae], 259 AZ63 (Timminco) [Me], 302
ASTM HZ32A [Me], 307
AZ63A (ASTM) [Mc], 302
A-S12UY4 (NF) [Ae], 259 ASTM K1A [Me], 307
A-S13 (NF) [Ae], 259 AZ67 (Otto Fuchs) [Aw], 219
ASTM LA141 [M], 307
AS17 (Otto Fuchs) [Aw], 218 ASTM M1C [Me], 308 AZ80 (Magnesium Elektron) [Mw] , 302
AZ80A (ASTM) [Mw], 302
A-S 17U4G (Valfond) [Ae], 259 ASTM MIA [Mw] , 312
A-S1SUNG (NF) [Ae] , 259 AZ80F (ASTM) [Mw], 302
ASTM PE [Mw] , 312
A-S20U (NF) [Ae], 259 AZS1 (ASTM) [Me], 302
ASTM QE22A [Me], 312
AS21 (ASTM) [Me], 299 AZ81A (ASTM) [Me], 302
ASTM QH21A [Me], 313
AS21 (Hydro Magnesium) [Me], 299 AZ91 (Magnesium Elektron) [Me], 302
ASTM WE43A [Mew], 313
AS21X1 (ASTM) [Me], 300 AZ91A (ASTM) [Me], 303
ASTM WE54A [Mew], 313
A-S22UNK (NF) [Ae], 259 ASTM ZC63A [Me], 313 AZ91 B (ASTM) [Me], 303
AS.25 (GM Metal) [Ae], 275 AZ91 C (ASTM) [Me], 303
ASTM ZC71 [Mw] , 313
A-S25UNG (NF) [Ae] , 260 AZ91 C (RIMA) [Me], 303
ASTM ZC71A [Mew], 314
AS.35 (GM Metal) [Ae], 275 AZ910 (ASTM) [Me], 303
ASTM ZE41A [Me], 314
AS41 (ASTM) [Me], 300 ASTM ZE63A [Me], 314 AZ91 E (ASTM) [Me], 303
AS41 A (ASTM) [Me], 300 AZ91 HP (RIMA) [Me], 303
ASTM ZH62A [Me], 314
AS41 B (ASTM) [Me], 300 AZ91 UX (Timminco) [Me], 304
ASTM ZK21A [Mw], 314
ASTM 17 [Tw], 321 AZ91X (Timminco) [Me], 304
ASTM ZK40A [Mw], 314
ASTM 3AI-2.5V [Tw], 321 AZ92 (Timminco) [Me], 304
ASTM ZK51A [Me], 314
AZ92A (ASTM) [Me], 304
ASTM AM1 OOA [Me], 298 ASTM ZK60A [Mw], 315
ASTM AM20 [Me], 298 AZM (Magnesium Elektron) [Mw], 304
ASTM ZK61A [Me], 315
ASTM AM50A [Me], 298 ASTM ZM21 [Mw] , 315
ASTM AM50B [Me], 298 Atomised AI 97% (ALPOCa) [Ap], 295 B
ASTM AM60 [Me], 299 Atomised AI 99.7% (ALPOCa) [Ap] , 295
ASTM AM60A [Me], 299 Atomised AI 99.9% (ALPOCa) [Ap], 296 B-26-0 (Brush Wellman) [Be], 345
ASTM AM60B [Me], 299 Atomised AI 99.97% (ALPOCa) [Ap], 296 B 120 VCA (Crucible Steel Co.) [Tw], 330
ASTM AS21 [Me], 299 Atomised AI 99.99% (ALPOCa) [Ap], 296 B201.1 (AA) [Ae], 276
ASTM AS21X1 [Me], 300 A-U2GN (NF) [Aw] , 218 B319.0 (AA) [Ae], 276
ASTM AS41 [Me], 300 A-U4G (NF) [Aw], 218 B319.1 (AA) [Ae], 276
ASTM AS41A [Me], 300 A-U4G1 (NF) [Aw], 218 B356.0 (AA) [Ae], 276
ASTM AS41 B [Me], 300 A-U4NT (NF) [Ae], 260 B356.2 (AA) [Ae], 276
ASTM AZ1 OA [Mw], 300 A-U4PB (NF) [Aw] , 218 B357.0 (AA) [Ae], 276
ASTM AZ21X1 [Mw], 300 A-U4T (NF) [Ae], 260 B357.2 (AA) [Ae], 276
ASTM AZ31 B [Mw] , 301 A-U5GT (NF) [Ae], 260 B380.0 (AA) [Ae], 276
ASTM AZ31 C [Mw] , 301 A-U5NKZr (NF) [Ae], 260 B380.1 (AA) [Ae], 276
ASTM AZ61A [Mw] , 301 A-U8S (NF) [Ae], 260 B384.0 (AA) [Ae], 276
ASTM AZ63A [Me], 302 A-U8SZ (NF) [Ae] , 260 B384.1 (AA) [Ae], 276
ASTM AZSOA [Mw] , 302 A-U10G (NF) [Ae], 260 B390.0 (AA) [Ae], 276
ASTM AZSOF [Mw], 302 A-U10S4 (NF) [Ae], 260 B390.1 (AA) [Ae] , 276
ASTM AZS1 [Me], 302 Autodur (VAW) [Ae] , 276 B413.0 (AA) [Ae], 277
518 Index of Alloy Names and Designations
B413.1 (AA) [Ac], 277 BS l155 [Ac] , 284 C380.0 (AA) [Ac], 277
B443.0 (AA) [Ac], 277 BS L169 [Ac], 284 C380.1 (AA) [Ac], 277
B443.1 (AA) [Ac], 277 BS l 173 [Ac] , 284 C384.0 (AA) [Ac], 278
B535.0 (AA) [Ac], 277 BS l 174 [Ac] , 284 C384.1 (AA) [Ac], 278
B535.2 (AA) [Ac] , 277 BS lMO [Ac], 284 C443.0 (AA) [Ac], 278
BA170 (AS) [Ac] , 277 BS lM2 [Ac], 285 C443.1 (AA) [Ac], 278
Ballette LAZ933 [M], 307 BS lM4 [Ac], 285 C443.2 (AA) [Ac] , 278
Beta C (-) [Tcw] , 330 BS lM5 [Ac], 285 Calypso 25M (Affimet) [Ac], 278
Beta III (-) [Tw], 330 BS lM6 [Ac], 285 Calypso 41 R (Affimet) [Ac], 278
BOAl UK AM62 [Aw], 214 BS lM9 [Ac], 285 Calypso 43B (Affimet) [Ac], 278
BOAl UK AM65 [Aw], 214 BS lM12 [Ac], 285 Calypso 43X (Affimet) [Ac], 278
BOAl UKAM68 [Aw], 215 BS lM13 [Ac], 285 Calypso 49R (Afflmet) [Ac], 278
British Alcan (AHOE) 03 [Aw], 143 BS lM16 [Ac], 285 Calypso 61 S (Affimet) [Ac], 279
British Alcan (AHOE) 54 [Aw], 148 BS lM20 [Ac], 286 Calypso 67B (Affimet) [Ac], 279
British Alcan (AHOE) 57 [Aw], 148 BS lM21 [Ac], 286 Calypso 67B1 (Affimet) [Ac], 279
British Alcan (Plate) Oural 79 [Aw], 220 BS lM22 [Ac], 286 Calypso 67N (Affimet) [Ac], 279
British Aluminium Alumec 79 [Aw], 214 BS lM24 [Ac], 286 Calypso 67N1 (Affimet) [Ac], 279
British Aluminium Alumec 89 [Aw], 214 BS lM25 [Ac], 286 Calypso 67R (Affimet) [Ac], 279
British Aluminium Ouralcan 90/10 [Aw], 220 BS LM26 [Ac], 286 Calypso 67R1 (Affimet) [Ac], 279
Ronald Britton & Co. Fine [Ap] , 296 BS LM27 [Ac], 286 Calypso 67R2 (Affimet) [Ac], 280
Ronald Britton & Co. Ink Lining [Ap], 296 BS LM28 [Ac] , 286 Calypso 67S (Affimet) [Ac], 280
Ronald Britton & Co. lining [Ap], 296 BS LM29 [Ac], 287 Calypso 67S2 (Affimet) [Ac], 280
Ronald Britton & Co. Primary Grade [Ap], BS LM30 [Ac], 287 Calypso 67XB (Affimet) [Ac] , 280
296 BS LM31 [Ac], 287 Calypso 67XB1 (Affimet) [Ac], 280
Ronald Britton & Co. Secondary Grade [Ap] , BS MAG1 [Mc], 309 Calypso 67XR (Affimet) [Ac], 280
296
BS MAG2 [Mc], 309 Calypso 67XR1 (Affimet) [Ac], 280
Ronald Britton & Co. Standard [Ap], 296
BS MAG3 [Mc] , 309 Calypso 69B (Affimet) [Ac], 280
Ronald Britton & Co. Super Ink lining [Ap],
BS MAG4 [Mc], 310 Calypso 69R (Affimet) [Ac], 280
296
BS MAG5 [Mc] , 310 Calypso 69R2 (Affimet) [Ac], 281
Brush Wellman AlbeMet AM 162 [Bw], 345
BS MAG6 [Mc], 310 Calypso 69S (Affimet) [Ac], 281
Brush Wellman AlbeMet AM162 Extruded
Bar [Bw], 345 BS MAG7 [Mc], 310 Calypso 82P1 (Affimet) [Ac], 281
Brush Wellman AlbeMet AM162 Rolled BS MAG8 [Mc] , 310 Calypso 85R (Affimet) [Ac] , 281
Sheet [Bw], 345 BS MAG9 [Mc] 310 Calypso 87P (Affimet) [Ac], 281
Brush Wellman AlbeMet AM162H [Bw], 345 BS MAG12 [Mc] , 310 Calypso 92A (Affimet) [Ac] , 281
Brush Wellman B-26-0 [Bc], 345 BS MAG13 [Mc] , 310 CEN 1050A [Aw], 152
Brush Wellman 1-220B [Bw], 345, 346 BS MAG14 [Mc], 311 CEN 1070A [Aw], 153
Brush Wellman 1-250 [Bw], 346 BS MAG-E-121M [Mw], 308 CEN 10aOA [Aw], 153
Brush Wellman 1-400 [Bw], 346 BS MAG-S-111O [Mc], 308 CEN 1085 [Aw], 153
Brush Wellman 1-70A [Bw], 346 BS MAG-x-101 [Mw], 308 CEN 1090 [Aw], 154
Brush Wellman 1-70B [Bw], 346 BS MAG-x-111 [Mw], 308 CEN 1100 [Aw], 154
Brush Wellman IF-1 [Bw], 346 BS MAG-x-121 [Mw], 308 CEN 1198 [Aw], 155
Brush Wellman IP-70 [Bp], 346 BS MAG-x-131 [Mw] , 308 CEN 1199 [Aw], 155
Brush Wellman 0-50 [Bp], 347 BS MAG-x-141 [Mw], 309 CEN 1200 [Aw], 156
Brush Wellman PF-60 [Bw], 347 BS MAG-x-151 [Mw], 309 CEN 1350 [Aw], 157
Brush Wellman PR-200 [Bw], 347 BS MAG-x-161 [Mw], 309 CEN 1370 [Aw], 157
Brush Wellman PR-200E [Bw], 347 BS 2TA1 [Tw], 317 CEN 2011 [Aw], 159
Brush Wellman S-200 [Bw], 347 BS 2TA10 [Tw], 317 CEN 2011A [Aw], 159
Brush Wellman S-200F [Bw], 348 BS TA18 [Tw], 337 CEN 2014 [Aw], 160
Brush Wellman S-200FC [Bw], 348 BS TA20 [Tw], 337 CEN 2017A [Aw], 161
Brush Wellman S-200FH [Bw], 348 BS 2TA21 [Tw], 317 CEN 2024 [Aw], 162
Brush Wellman S-65B [Bw], 348 BS TA45 [Tw], 337 CEN 2030 [Aw], 162
Brush Wellman SP-200F lap], 348 BT1-0 (GOST) [Tw], 330 CEN 2124 [Aw], 164
Brush Wellman SP-65 [ap], 348 BT1-00 (GOST) [Tw], 330 CEN 2214 [Aw], 164
Brush Wellman SR-200 [Bw], 349 CEN 2219 [Aw], 165
Brush Wellman SR-200E [Bw], 349 c CEN
CEN
2618A [Aw], 166
3003 [Aw], 167
BS 2199 [Ac] , 233
BS 21121 [Mw], 297 C 50S (Alunord) [Aw], 220 CEN 3004 [Aw], 167
BS 2TA1 [Tw], 317 C130AM (Crucible Steel Co) [Tw], 330 CEN 3005 [Aw] , 168
BS 2TA10 [Tw], 317 C355.0 (AA) [Ac], 277 CEN 3103 [Aw], 169
BS 2TA21 [Tw], 317 C355.1 (AA) [Ac], 277 CEN 3104 [Aw] , 169
BS 716B [Ac], 244 C355.2 (AA) [Ac], 277 CEN 3105 [Aw], 170
BS 5008B [Ac], 248 C356.0 (AA) [Ac], 277 CEN 4004 [Aw], 171
BS 5018A [Ac], 248 C356.2 (AA) [Ac], 277 CEN 4006 [Aw], 171
BS l119 [Ac], 284 C357.0 (AA) [Ac], 277 CEN 4007 [Aw], 171
BS l 154 [Ac] , 284 C357.2 (AA) [Ac], 277 CEN 4043A [Aw], 172
Index of Alloy Names and Designations 519
CEN 4045 [Aw], 172 CEN 45200 [Ac], 252 DIN AI 99.8 MgO.5 [Aw], 210
CEN 4047A [Aw], 173 CEN 45300 [Ac], 252 DIN AI 99.85 [Aw], 211
CEN 4104 [Aw], 173 CEN 45400 [Ac], 252 DIN AI 99.85 Mg Si [Aw], 211
CEN 4343 [Aw], 173 CEN 46000 [Ac], 252 DIN AI 99.85 Mg SiOA [Aw], 211
CEN 5005 [Aw], 174 CEN 46100 [Ac], 253 DIN AI 99.85 Mg1 [Aw], 211
CEN 5019 [Aw], 175 CEN 46200 [Ac], 253 DIN AI 99.9 [Aw], 211
CEN 5049 [Aw], 176 CEN 46300 [Ac] , 253 DIN AI 99.9 Mg Si [Aw], 211
CEN 5050 [Aw], 176 CEN 46400 [Ac] , 253 DIN AI 99.9 MgO.5 [Aw], 211
CEN 5051A [Aw], 176 CEN 46500 [Ac], 253 DIN AI 99.9 Mg1 [Aw], 211
CEN 5052 [Aw], 177 CEN 46600 [Ac], 253 DIN AI 99.95 MgO.5 [Aw), 211
CEN 5083 [Aw] , 179 CEN 47000 [Ac], 253 DIN AI 99.5TiO.6 [Aw), 210
CEN 5086 [Aw], 180 CEN 47100 [Ac], 253 DIN A IFeMg [Aw], 212
CEN 5087 [Aw], 180 CEN 48000 [Ac] , 254 DIN AI Mg SiO.3 [Aw], 212
CEN 5154A [Aw], 181 CEN 51000 [Ac] , 254 DIN AI Mg SiO.5 [Aw), 212
CEN 5182 [Aw], 182 CEN 51100 [Ac] , 254 DIN AI Mg SiO.7 [Aw), 213
CEN 5183 [Aw], 182 CEN 51200 [Ac] , 254 DIN AI Mg SiO.8 [Aw], 213
CEN 5251 [Aw], 183 CEN 51300 [Ac] , 254 DIN AI Mg Si1 [Aw), 213
CEN 5356 [Aw], 184 CEN 51400 [Ac] , 254 DIN AI MgO.5 [Aw], 212
CEN 5454 [Aw], 185 CEN 71000 [Ac] , 254 DIN AI Mg1 [Aw], 212
CEN 5456A [Aw], 185 CEN MG-P-61 [Mw], 311 DIN AI Mg1.8 [Aw), 212
CEN 5657 [Aw], 186 CEN Ti P63 [Tw], 340 DIN AI Mg3 EQ [Aw], 212
CEN 5754 [Aw], 187 CEN Ti P99001 [Tw], 341 DIN AI Mg3.5 [Aw], 212
CEN 6005A [Aw], 189 CEN Ti P99002 [Tw], 341 DIN AI Mn Cu [Aw), 213
CEN 6012 [Aw], 189 CEN Ti P99003 [Tw], 341 DIN AI Mn1 [Aw], 213
CEN 6056 [Aw], 190 Certal (Alusuisse) [Aw], 220 DIN AI Zn4.5 MgO.8 [Aw], 214
CEN 6060 [Aw], 190 Class 1 (JIS) [Tw], 330 DIN AI Zn4.5 Mg1 [Aw], 214
CEN 6061 [Aw], 192 Class 2 (JIS) [Tw], 330 DIN E-AI [Aw], 220
CEN 6063 [Aw], 193 Class 3 (JIS) [Tw], 331 DIN E-AI Mg SiO.5 [Aw], 220
CEN 6082 [Aw], 195 Code 12 (Timetal) [Tcw] , 331 DIN GB-AICu4Ti [Ac] , 282
CEN 6101 [Aw], 196 Comeca AZ31 B [Mw] , 301 DIN GB-AICu4TiMg [Ac), 282
CEN 6106 [Aw], 196 Comeca AZ31 B TP [Mw] , 301 DIN GB-AIMg3 [Ac), 282
CEN 6262 [Aw], 197 Commercial Purity (ALPOCO) [Ap], 296 DIN GB-AIMg3Si [Ac], 282
CEN 7010 [Aw], 199 Contal (Alusuisse) [Aw], 220 DIN GB-AIMg5 [Ac), 283
CEN 7020 [Aw], 200 Crucible Steel Co. B 120 VCA [Tw], 330 DIN GB-AIMg5Si [Ac), 283
CEN 7021 [Aw], 201 Crucible Steel Co. C130AM [Tw], 330 DIN GB-AISi10Mg [Ac], 283
CEN 7039 [Aw], 201 DIN GB-AISi10Mg(Cu) [Ac), 283
CEN 7049A [Aw], 202 D DIN GB-AISi11 [Ac] , 283
CEN 7050 [Aw], 202 DIN GB-AISi12 [Ac), 283
CEN 7072 [Aw], 203 D355.2 (AA) [Ac] , 281 DIN GB-AISi12(Cu) [Ac], 283
CEN 7075 [Aw], 204 D357.0 (AA) [Ac] , 281 DIN GB-AISi5Mg [Ac], 283
CEN 7149 [Aw], 205 D380.0 (AA) [Ac] , 281 DIN GB-AISi6Cu4 [Ac], 283
CEN 7175 [Aw], 206 D380.1 (AA) [Ac] , 282 DIN GB-AISi7Mg [Ac], 283
CEN 7178 [Aw], 206 Decoltal 500 (Alusuisse) [Aw], 220 DIN GB-AISi9Cu3 [Ac), 283
CEN 7475 [Aw], 207 Deutsche Titan Tikrutan LT 24 [Tw], 341 DIN GB-AISi9Mg [Ac], 283
CEN 8006 [Aw], 207 Deutsche Titan Tikrutan LT 25 [Tw], 341 DIN GBD-AIMg9 [Ac) , 284
CEN 8011A [Aw], 208 Deutsche Titan Tikrutan LT 26 [Tw], 341 DIN GBD-AISi10Mg [Ac] , 284
CEN 8079 [Aw], 209 Deutsche Titan Tikrutan LT 27 [Tcw] , 342 DIN GBD-AISi12 [Ac], 284
CEN 21000 [Ac], 250 Deutsche Titan Tikrutan LT 31 [Tw], 342 DIN GBD-AISi12(Cu) [Ac), 284
CEN 21100 [Ac], 250 Deutsche Titan Tikrutan LT 33 [Tw], 342 DIN GBD-AISi9Cu3 [Ac], 284
CEN 41000 [Ac], 250 Deutsche Titan Tikrutan LT 34 [Tw], 342 DIN Kryal A199.999 - >99.9999 [Aw), 222
CEN 42000 [Ac], 250 Deutsche Titan Tikrutan LT 35 [Tw], 342 DIN LW 3.7124 [Tw], 319
CEN 42100 [Ac], 250 Deutsche Titan Tikrutan RT 12 [Tw], 342 DIN LW 3.7144 [Tw], 319
CEN 42200 [Ac], 250 Deutsche Titan Tikrutan RT 12 Pd [Tw], 343 DIN LW 3.7164 [Tw), 319
CEN 43000 [Ac], 251 Deutsche Titan Tikrutan RT 15 [Tw], 343 DIN LW 3.7174 [Tw], 320
CEN 43100 [Ac], 251 Deutsche Titan Tikrutan RT 15 Pd [Tw], 343 DIN LW 3.7184 [Tw), 320
CEN 43200 [Ac], 251 Deutsche Titan Tikrutan RT 18 [Tw], 343 DIN Ti AI6 V4 [Tw], 339
CEN 43300 [Ac] , 251 Deutsche Titan Tikrutan RT 18 Pd [Tw], 343 DIN Wk. 3.0255 (AI995) [Aw], 143
CEN 43400 [Ac] , 251 Deutsche Titan Tikrutan RT 20 [Tw], 343 DIN Wk. 3.0257 (E-AI) [Aw], 143
CEN 44000 [Ac] , 251 DIN 3.5312 [Mw] , 297 DIN Wk. 30285 (AI99.8) [Aw), 143
CEN 44100 [Ac], 251 DIN 3.5612 [Mw] , 297 DIN Wk. 30305 (AI99.9) [Aw], 143
CEN 44200 [Ac], 251 DIN 3.5812 [Mw] , 297 DIN Wk. 30315 (AIMn1) [Aw], 143
CEN 44300 [Ac], 252 DIN AI 99 [Aw], 210 DIN Wk. 3.0385 (AI99.98R) [Aw], 144
CEN 44400 [Ac], 252 DIN AI 99.5 [Aw], 210 DIN Wk. 3.0400 [Aw], 144
CEN 45000 [Ac], 252 DIN AI 99.7 [Aw], 210 DIN Wk. 3.0915 (AIFeSi) [Aw], 144
CEN 45100 [Ac], 252 DIN AI 99.8 [Aw], 210 DIN Wk. 3.1255 (AICuSiMn) [Aw], 144
520 Index of Alloy Names and Designations
DIN Wk. 3.1305 (AICu2.5MgO.5) [Aw], 144 Elektron EQ21 (Magnesium Elektron) [Me], Glare 1 (Structural Laminates Co.) [Aw], 221
DIN Wk. 3.1325 (AICuMg1) [Aw], 144 304 Glare 2 (Structural Laminates Co.) [Aw], 221
DIN Wk. 3.1355 (AICuMg2) [Aw], 144 Elektron EZ33 (Magnesium Elektron) [Me], Glare 3 (Structural Laminates Co) [Aw], 221
DIN Wk. 3.1855 (AICuBiPb) [Aw], 145 304
Glare 4 (Structural Laminates Co.) [Aw], 222
DIN Wk. 3.2305 (AIMgSi) [Aw], 145 Elektron QE22 (Magn;;c',m Elektron) [Me],
Glare 5 (Structural Laminates Co) [Aw], 222
304
DIN Wk. 3.2315 (AIMgSi1) [Aw], 145 Glare 5-F1 (Structural Laminates Co.) [Aw]
Elektron WE43 (Magnesium Elektron) [Mew] 222 '
DIN Wk. 3.3206 (AIMgSiO.5) [Aw], 145 W5 '
DIN Wk. 3.3208 (AI99.9MgSi) [Aw], 145 Glare 5-F2 (Structural Laminates Co) [Aw]
Elektron WE54 (Magnesium Elektron) [Mew], 222 '
DIN Wk. 3.3211 (AIMg1 SiCu) [AwJ,145 305
DIN Wk. 3.3308 (AI99.9MgO.5) [Aw], 146 Glare 5-FW (Structural Laminates Co.) [Aw],
Elektron ZC63 (Magnesium Elektron) [Me],
222
DIN Wk. 3.3309 [Aw], 146 305
Glare 6 (Structural Laminates Co.) [Aw], 222
DIN Wk. 3.3315 (AIMg1) [Aw], 146 Elektron ZE41 (Magnesium Elektron) [Me],
305 GM Metal AG.1 0 [Ac], 270
DIN Wk. 3.3318 (AI99.9Mg1) [Aw], 146
Elektron ZM21 (Magnesium Elektron) [Mw] GM Metal AG.20 [Ae], 270
DIN Wk. 3.3318 [Aw], 146
305 ' GM Metal AG.25 [Ae], 270
DIN Wk. 3.3319 [Aw], 146
EQ21A (ASTM) [Me], 305 GM Metal AI/Sb 10 [Ae], 274
DIN Wk. 3.3326 (AIMg1.8) [Aw], 146
ES70 (0110 Fuchs) [Aw], 220 GM Metal AI/Sr 5 [Ac], 275
DIN Wk. 3.3523 (AIMg2.5) [Aw], 146
Extrudal-043 (Alusuisse) [Aw], 221 GM Metal AI/Sr 10 [Ae], 275
DIN Wk. 3.3526 (AIMg2MnO.3) [Aw], 146
Extrudal-050 (Alusuisse) [Aw], 221 GM Metal AI Sr1 0 Ca3 [Ae], 273
DIN Wk. 3.3535 (AIMg3) [Aw], 147
EZ33A (ASTM) [Me], 306 GM Metal AS.25 [Ae], 275
DIN Wk. 3.3555 (AIMg5) [Aw], 147
GM Metal AS.35 [Ae], 275
DIN Wk. 3.4335 (AIZn4.5Mg1) [Aw], 147
Goodfellow Titanium/Aluminium [Tp], 343
DIN Wk. 3.4365 (AIZnMgCu15) [Aw], 147 F
GOST AK21M2.5N2.5 [Ae], 270
DIN Wk. 3.5003 [Mw], 297
F7 (ASTM) [Tw], 331 GOST AK4M2116 (AI17B) [Ae], 270
DIN Wk. 3.5101 [Me], 297
F100 (NF) [Ae], 282 GOST AK4M4 (AI15B) [Ae], 270
DIN Wk. 3.5103 [Me], 297
F101 (NF) [Ae], 282 GOST AK5M2 (AI3B) [Ae], 270
DIN Wk. 3.5161 [Mw], 297
F300 (NF) [Ae], 282 GOST AK5M7 (A11 OB) [Ae], 270
DIN Wk. 3.5812 [Me], 297
F356.0 (AA) [Ae], 282 GOST AK7 (AI9B) [Ae], 270
DIN Wk. 3.5912[Me], 297
F356.2 (AA) [Ae], 282 GOST AK7M2 (AI14B) [Ac], 270
DIN Wk. 3.7025[Tw], 318
Fine (Ronald Brillon & Co.) [Ap], 296 GOST AK9 (AI4B) [Ae], 270
DIN Wk. 3.7035[Tw], 318
GOST AI 1 [Ae], 270
DIN Wk. 3.7055[Tw], 318
GOST AI 2 [Ae], 271
DIN Wk. 3.7065[Tw], 318 G
GOST AI 3 [Ae], 271
DIN Wk. 3.7105 [Tew], 318
G-A3Z1 (NF) [Me], 306 GOST AI 4 [Ae], 271
DIN Wk. 3.7110 [Tw], 318
G-A6Z1 (NF) [Mw], 306 GOST A14-1 [Ae], 271
DIN Wk. 3.7115 [Tw], 318
G-A7Z1 (NF) [Mw], 306 GOST AI 5 [Ae], 271
DIN Wk. 3.7145 [Tw], 319
G-A8Z (NF) [Mw], 306 GOST AI 5-1 [Ae], 271
DIN Wk. 3.7155 [Tw], 319
G-A9 (NF) [Me], 306 GOST AI 6 [Ae], 271
DIN Wk. 3.7165 [Tw], 320
G-A9Z1 (NF) [Me], 306 GOST AI 7 [Ae], 271
DIN Wk. 3.7175 [Tw], 320
G-Ag25TR (NF) [Me], 306 GOST AI 8 [Ae], 271
DIN Wk. 3.7185 [Tw], 320
G-AICu4Ti (Onorm) [Ae], 282 GOST AI 9 [Ae], 271
DIN Wk. 3.7225 [Tw], 320
G-AICu4TiMg (Onorm) [Ae], 282 GOST A19-1 [Ae], 271
DIN Wk. 3.7235 [Tw], 321
Galvomag (Dow Magnesium) [Mw], 306 GOST AI 11 [Ae], 271
DIN Wk. 3.7255 [Tw], 321
Galvorod (Dow Magnesium) [Mw], 306 GOST AI 13 [Ae], 271
Dow Magnesium AE42X1 [Me], 298
GB-AICu4Ti (DIN) [Ae], 282 GOST AI 19 [Ae], 271
Dow Magnesium Galvomag [Mw], 306
GB-AICu4TiMg (DIN) [Ac], 282 GOST AI21 [Ac], 271
Dow Magnesium Galvorod [Mw], 306
GB-AIMg3 (DIN) [Ae], 282 GOST AI 22 [Ac], 271
OS 4162 [Ae], 247
GB-AIMg3Si (DIN) [Ae], 282 GOST AI 23 [Ae], 271
DS 4163 [Ae], 247
GB-AIMg5 (DIN) [Ae], 283 GOST AI 23-1 [Ae], 272
OS 4244 [Ae], 247
GB-AIMg5Si (DIN) [Ae], 283 GOST AI 24 [Ac], 272
DS 4251 [Ae], 247
GB-AISi10Mg (DIN) [Ae], 283 GOST AI 25 [Ac], 272
OS 4253 [Ae], 247
GB-AISi10Mg(Cu) (DIN) [Ac], 283 GOST AI 27 [Ac], 272
OS 4254 [Ae], 247
GB-AISi11 (DIN) [Ae], 283 GOST AI 27-1 [Ac], 272
OS 4260 [Ae], 248
GB-AISi12 (DIN) [Ae] , 283 GOST AI 28 [Ae], 272
OS 4261 [Ae], 248
GB-AISi12(Cu) (DIN) [Ae], 283 GOST AI 29 [Ae], 272
OS 4438 [Ae], 248
GOST AI 30 [Ae], 272
DTD 5053 [Tw], 328 GB-AISi5Mg (DIN) [Ae], 283
GB-AISi6Cu4 (DIN) [Ae], 283 GOST AI 32 [Ae], 272
DTD 5083 [Tw], 328
GB-AISi7Mg (DIN) [Ae], 283 GOST AI 33 [Ae], 272
DTD 5163 [Tw], 328
GB-AISi9Cu3 (DIN) [Ae], 283 GOST AI 34 [Ae], 272
Dural 79 (British Alean (Plate [Aw], 220
GB-AISi9Mg (DIN) [Ac], 283 GOST BT1-0 [Tw], 330
Duralcan 90/10 (British Aluminium) [Aw], 220
GBD-AIMg9 (DIN) [Ae], 284 GOST BT1-00 [Tw], 330
GBD-AISi10Mg (DIN) [Ae], 284 GR-1 (Titanium Industries) [Tw], 331
E GBD-AISi12 (DIN) [Ae], 284 GR-2 (Titanium Industries) [Tew], 331
GBD-AISi12(Cu) (DIN) [Ae] , 284 GR-3 (Titanium Industries) [Tcw], 331
E-AI (DIN) [Aw], 220
GBD-AISi9Cu3 (DIN) [Ae], 284 GR-4 (Titanium Industries) [Tcw], 331
E-AI Mg SiO.5 (DIN) [Aw], 220 GR-5 (Titanium Industries) [Tcw], 331
Index of Alloy Names and Designations 521
GR-7 (Titanium Industries) [Tew), 332 1-220B (Brush Wellman) [Bw], 346 JIS AC4C (casting) [Ac] , 266
GR-12 (Titanium Industries) [Tw), 331 1-250 (Brush Wellman) [Bw), 346 JIS AC4C.1 [Ac], 266
Grade 1 (ASTM) [Tw), 332 1-400 (Brush Wellman) [Bw), 346 JIS AC4C.2 (ingot) [Ac) , 266
Grade 2 (ASTM) [Tw), 332 IF-1 (Brush Wellman) [Bw), 346 JIS AC4CH (casting) [Ac), 266
Grade 3 (ASTM) [Tw), 332 IMI 314A [Tw), 324 JIS AC4CH.1 [Ac), 266
Grade 4 (ASTM) [Tew), 333 IMI 315 [Tw), 324 JIS AC4CH.2 (ingot) [Ac), 266
Grade 5 (ASTM) [Tw), 333 IMI 367 [Tw), 324 JIS AC4D (casting) [Ac), 266
Grade 6 (ASTM) [Tw), 333 IMI 551 [Tw), 324 JIS AC4D.1 [Ac), 266
Grade 7 (ASTM) [Tw], 333 IMI646 [Tw], 325 JIS AC4D.2 (ingot) [Ac], 266
Grade 9 (ASTM) [Tw), 333 IMI 679 [Tw), 325 JIS AC5A (casting) [Ac], 266
Grade 11 (ASTM) [Tw), 333 IMI 6BO [Tw], 325 JIS AC5A.1 [Ac] , 266
Grade 12 (ASTM) [Tew] , 334 IMISB5 [Tw], 325 JIS AC5A.2 (ingot) [Ac] , 266
Grade 23 (ASTM) [Tw), 334 IMI 700 [Tw), 325 JIS AC7A (casting) [Ae] , 267
Grade 99BOA (Mag Corp) [Me), 306 IMI B29 [Tw], 326 JIS AC7 A.l [Ac], 267
Grade 9990A (Mag Corp) [Me), 307 IMI B34 [Tw), 326 JIS AC7A.2 (ingot) [Ac), 267
G-Z4TR (NF) [Me), 306 Ink Lining (Ronald Britton & Co.) [Ap] , 296 JIS ACBA (casting) [Ae), 267
G-Z5Zr (NF) [Mw) , 306 IP-70 (Brush Wellman) [Bp], 346 JIS ACBA.1 [Ac) , 267
ISO AI-Cu4MgTi [Ac), 274 JIS ACBA.2 (ingot) [Ac), 267
H ISO AI-Cu4Ni2Mg2 [A c) , 274 JIS ACBB (casting) [Ac) , 267
ISO AI-Cu4Ti [Ac), 274 JIS ACBB.l [Ac] , 267
High Purity Magnesium (Timminco) [Mcw), ISOAI-Mgl0 [A c) , 274 JIS ACBB.2 (ingot) [Ac), 267
307 ISO AI-Mg3 [A c) , 274 JIS ACBC (casting) [A c) , 267
HK31A (ASTM) [Mcw) , 307 ISO AI-Mg3Si2 [A c) , 274 JIS ACBC.1 [Ac), 267
HM21A (ASTM) [Mw) , 307 ISO AI-Mg5Sil [Ac), 274 JIS ACBC.2 (ingot) [Ac), 267
HM31A (ASTM) [Mw) , 307 ISO AI-Mg6 [Ac), 274 JIS AC9A (casting) [Ac] , 267
Hoogovens 1000 [Aw), 151 ISO AI-Si5 [Ac) , 274 JIS AC9A.1 [Ac], 267
Hoogovens 1001 [Aw), 151 ISO AI-Si5Cu1Mg [Ac), 274 JIS AC9A.2 (ingot) [Ac), 267
Hoogovens 1010 [Aw), 151 ISO AI-Si5Cu3 [Ac) , 274 JIS AC9B (casting) [Ac), 268
Hoogovens 1070 [Aw), 153 ISO AI-Si5Fe [Ac] , 274 JIS AC9B.1 [A c) , 268
Hoogovens 2140 [Aw), 164 ISO AI-Si5Mg [Ae) , 274 JIS AC9B.2 (ingot) [Ac), 268
Hoogovens 2170 [Aw), 164 ISO AI-Si6Cu4 [Ac) , 275 JIS AD1.1 [Ac), 268
Hoogovens 2240 [Aw), 165 ISO AI-SiSCu4Fe [Ac], 275 JIS AD1.2 (ingot) [Ac], 268
Hoogovens 3000 [Aw), 166 ISO AI-Si7Mg [Ac], 275 JIS AD3.1 [Ac), 268
Hoogovens 3000 Clad [Aw), 166 ISO AI-Si7Mg(Fe) [Ae] , 275 JIS AD3.2 (ingot) [Ac], 268
Hoogovens 3010 [Aw), 168 ISO AI-SiBCu3Fe [Ac], 275 JIS AD5.1 [Ac) , 268
Hoogovens 3530 [Aw), 170 ISO AI-Si10Mg [Ac) , 275 JIS AD5.2 (ingot) [Ac], 268
Hoogovens 3530 Clad [Aw), 170 ISO AI-Si12 [Ae), 275 JIS AD6.1 [Ac] , 268
Hoogovens 3540 [Aw), 171 ISO AI-Si12Cu [Ae) , 275 JIS ADS.2 (ingot) [Ac], 268
Hoogovens 3540 Clad [Aw), 171 ISO AI-Si12CuFe [Ac) , 275 JISAD10.1 [Ac) , 268
Hoogovens 3541 [Aw), 171 ISO AI-Si12Fe [Ac), 275 JIS AD1 0.2 (ingot) [Ac]. 268
Hoogovens 3560 Clad [Aw), 171 ISO AI-Zn5Mg [Ac), 275 JISAD10Z.l [Ac), 268
Hoogovens 5010 [Aw), 174 JIS AD12.1 (LME) [Ac] , 269
Hoogovens 5020 [Aw), 175 JIS AD12.2 (ingot) [Ac], 269
J
Hoogovens 5030 [Aw), 175 JIS AD12Z.1 [A c) , 269
Hoogovens 5400[Aw), 184 JIS AC1A (casting) [Ac), 264 JIS AD14.1 [Ac] , 269
Hoogovens 5503[Aw), 185 JIS AC1A.l [Ac) , 264 JIS AD14.2 (ingot) [A c) , 269
Hoogovens 5510[Aw), 185 JIS AC1A.2 (ingot) [Ac) , 264 JIS ADC1 (casting) [Ac) , 269
Hoogovens 5520[Aw), 185 JIS AC1 B (casting) [Ac), 265 JIS ADC3 (casting) [Ae) , 269
Hoogovens 6010[Aw), 189 JIS AC1B.1 [Ac), 265 JIS ADC5 (casting) [Ae), 269
Hoogovens 6560[Aw), 198 JIS AC1 B.2 (ingot) [Ac) , 265 JIS ADC6 (casting) [Ac) , 269
Hoogovens 6630Clad [Aw), 198 JIS AC2A (casting) [Ac), 265 JIS ADC1 0 (casting) [Ac), 269
Hoogovens 7350 [Aw], 206 JIS AC2A.1 [Ac], 265 JIS ADC10Z (casting) [Ac), 269
Hoogovens 7750 [Aw], 207 JIS AC2A.2 (ingot) [Ac), 265 JIS ADC12 (casting) [Ac) , 269
Hoogovens 7790 [Aw], 207 JIS AC2B (casting) [Ae], 265 JIS ADC12Z (casting) [Ac), 269
Hoogovens Alustar [Aw], 214 JIS AC2B.l [Ac], 265 JIS ADC14 (casting) [A c) , 269, 270
Hydro Magnesium AE42 [Mc) , 298 JIS AC2B.2 (ingot) [Ac), 265 JIS Class 1 [Tw), 330
Hydro Magnesium AM20 [Me), 298 JIS AC3A (casting) [Ac), 265 JIS Class 2 [Tw), 330
Hydro Magnesium AS21 [Mc] , 299 JIS AC3A.1 [Ac), 265 JIS Class 3 [Tw), 331
Hydro Raufoss A356 [Ac), 262 JIS AC3A.2 (ingot) [Ac) , 265
HZ32A (ASTM) [Mc), 307 JIS AC4A (casting) [Ac), 265 K
JIS AC4A.l [Ac), 265
JIS AC4A.2 (ingot) [Ac) , 265 K1A (ASTM) [Mc) , 307
JIS AC4B (casting) [Ac] , 266 Kryal A199.999 - >99.9999 (DIN) [Aw), 222
1-70A (Brush Wellman) [Bw], 346 JIS AC4B.l [Ac] , 266
1-70B (Brush Wellman) [Bw), 346 JIS AC4B.2 (ingot) [Ac), 266
522 Index of Alloy Names and Designations
MAG14 (B8) [Me], 311 NF A-4 [Ae] , 254
L
MAG-CAL (Timminco) [Me], 308 NF A-5 [Ae], 254
2L99 (B8) [Ae] , 233 MAG-E-121M (B8) [Mw] , 308 NF A-5 [Aw], 210
2L 121 (B8) [Mw] , 297 Magnesium Elektron AE42 [Me], 298 NF A-5 Y4 [Ae] , 255
L 119 (B8) [Ae] , 284 Magnesium Elektron Al31 [Mw] , 300 NF A-5L [Aw], 210
L 154 (B8) [Ae], 284 Magnesium Elektron Al61 [Mw] , 301 NF A-5/LR [Ae] , 255
L 155 (B8) [Ac] , 284 Magnesium Elektron Al80 [Mw], 302 NF A-6GBe [Ae] , 255
L169 (B8) [Ae], 284 Magnesium Elektron Al91 [Me], 302 NF A-7/LR [Ae] , 255
L 173 (B8) [Ae], 284 Magnesium Elektron AlM [Mw], 304 NF AG 3 [Ae], 270
L 174 (B8) [Ae], 284 Magnesium Elektron Elektron EQ21 [Me], NF A-G3 [Aw], 210
L-2640 (UN E) [Ae], 284 304 NF A-G3T [Ae], 255
LA141 (A8TM) [M], 307 Magnesium Elektron Elektron EZ33 [Me], NF A-G4MC [Aw], 210
Lawson Mardon (LM) 8tar 1084 [Aw], 153 304
NF A-G4Z [Ae], 255
Lawson Mardon (LM) 8tar 1085 [Aw], 154 Magnesium Eleklron Eleklron QE22 [Me],
NF AG58 [Ae], 270
304
Lawson Mardon (LM) 8tar 1201 [Aw], 156 NF A-G6 [Ae], 255
Magnesium Eleklron Elektron WE43 [Mew],
Lawson Mardon (LM) 8tar 1602 [Aw], 158 NF A-G6Y4 [Ae], 256
305
Lawson Mardon (LM) 8tar 3103 [Aw], 169 NF A-G10 [Ae] , 255
Magnesium Elektron Elektron WE54 [Mew],
Lawson Mardon (LM) 8tar 8101 [Aw], 209 305 NF A-G108 Y4 [Ae], 255
LAZ933 (Baliette) [M], 307 Magnesium Elektron Elektron ZC63 [Me], NF A-G1 08Be [Ae], 255
LCB (Timetal) [Tw], 334 305 NF AG8 [Aw], 210
Lining (Ronald Britton & Co.) [Ap] , 296 Magnesium Elektron Elektron ZE41 [Me], NF A-M4 [Ae], 256
LMO (B8) [Ae], 284 305 NF A-82GT [Ae], 256
LM2 (B8) [Ae], 285 Magnesium Elektron Elektron ZM21 [Mw], NF A-82U [Ae] , 256
LM4 (B8) [Ae], 285 305
NF A-84G [Ae] , 256
LM5 (B8) [Ae], 285 Magnesium Elektron MELRAM072 [Mw], 311
NF A-85U3 [Ae], 256
LM6 (B8) [Ae], 285 Magnesium Elektron MELRAM072T8 [Mw],
NF A-85U3G [Ae] , 256
311
LM9 (B8) [Ae], 285 NF A-85UZ [Ae], 256
Magnesium Elektron MSR-A [Me], 312
LM12 (B8) [Ae], 285 NF A-S7G [Ae], 257
Magnesium Elektron M8R-B [Me], 312
LM13 (B8) [Ae], 285 NF A-87G03 [Ae], 257
Magnesium Elektron ZC71 [Mw], 313
LM16 (B8) [Ae], 285 NF A-87G06 [Ae], 257
Magnesium Elektron ZTY [Mw] , 315
LM20 (B8) [Ae], 286 NF A-87U3G [Ae], 257
Magnesium Elektron ZW3 [Mw] , 31"5
LM21 (B8) [Ae], 286 NF A-89 Y 4 [Ae], 257
MAG-8-1110 (B8) [Me], 308
LM22 (B8) [Ae], 286 NF A-89G [Ae] , 257
MAG-x-101 (B8) [Mw] , 308
LM24 (B8) [Ae], 286 NF A-89GU [Ae], 257
MAG-x-111 (B8) [Mw] , 308
LM25 (B8) [Ae], 286 NF A-89KG [Ae] , 258
MAG-x-121 (B8) [Mw] , 308
LM26 (B8) [Ae], 286 NF A-S9U3 [Ae] , 258
MAG-x-131 (B8) [Mw] , 308
LM27 (B8) [Ae], 286 NF A-S9U3 Y4 [Ae], 258
MAG-x-141 (B8) [Mw] , 309
LM28 (B8) [Ae], 286 NF A-S9U3Z Y4 [Ae], 258
MAG-x-151 (B8) [Mw] , 309
LM29 (B8) [Ae], 287 NF A-S1 OG [Ae], 258
MAG-x-161 (B8) [Mw] , 309
LM30 (B8) [Ae], 287 NF A-81 OG/R [Ae], 258
MD209 (Reynolds) [Aw], 222
LM31 (BS) [Ae], 287 NF A-S1 OUG [Ae], 258
MD276 (Reynolds) [Aw], 222
LW 3.7124 (DIN) [Tw], 319 NF A-811 UNG [Ae], 258
MD355 (Reynolds) [Aw], 222
LW 3.7144 (DIN) [Tw], 319 NF A-S12 [Ae] , 258
MD356 (Reynolds) [Aw] , 223
LW 3.7164 (DIN) [Tw], 319 NF A-S12 Y4 [Ae], 259
MELRAM072 (Magnesium Elektron) [Mw],
LW 3.7174 (DIN) [Tw], 320 311 NF A-S12N2G [Ae], 259
LW 3.7184 (DIN) [Tw], 320 MELRAM072T8 (Magnesium Elektron) [Mw] , NF A-S12U [Ae], 259,
311 NF A-S12UN [Ae], 259
M Metacs 20 (TYK) [Aew], 223, 287 NF A-S12UNG [Ae], 259
M-1 Hi-Potential (Timminco) [Mew], 308 MG Metal (RIMA) [Me], 311 NF A-S12UY4 [Ae] , 259
M1C (A8TM) [Me], 308 MG-C-43 (AECMA) [Me], 311 NF A-S 13 [Ae], 259
M14142 (UN8) [M], 308 MG-C-51 (AECMA) [Me], 311 NF A-S18UNG [Ae], 259
MA25 (Otto Fuchs) [Mw], 308 MG-C-61 (AECMA) [Me], 311 NF A-S20U [Ae], 259
Mag Corp Grade 9980A [Me], 306 MG-C-91 (AECMA) [Me], 311 NF A-S22UNK [Ae], 259
Mag Corp Grade 9990A [Me], 307 MG-P-43 (AECMA) [Mw] , 311 NF A-S25UNG [Ae] , 260
MAG1 (B8) [Me], 309 MG-P-61 (CEN) [Mw] , 311 NF A-8GO.5 [Aw], 218
MAG2 (B8) [Me], 309 MG-P-63 (AECMA) [Mw] , 311 NF A-SGMO.7 [Aw], 218
MAG3 (B8) [Me], 309 MIA (A8TM) [Mw] , 312 NF A-U2GN [Aw], 218
MAG4 (B8) [Me], 310 MIL R-81588 [Tw], 334 NF A-U4G [Aw], 218
MAG5 (B8) [Me], 310 M8R-A (Magnesium Elektron) [Me], 312 NF A-U4G1 [Aw], 218
MAG6 (B8) [Me], 310 M8R-B (Magnesium Elektron) [Me], 312 NF A-U4NT [Ae], 260
MAG7 (B8) [Me], 310 NF A-U4PB [Aw], 218
MAG8 (B8) [Me], 310
N NF A-U4T [Ae], 260
MAG9 (B8) [Me], 310 NF A-U5GT [Ae], 260
NBN 8GAICu2NiMg [Ae], 288
MAG12 (B8) [Me], 310 NF A-U5NKZr [Ae], 260
NBN 8GAICu4MgTi [Ae], 288
MAG13 (B8) [Me], 310 NF A-U8S [Ae], 260
NF 3003 [Aw], 167
Index of Alloy Names and Designations 523
NF A-USSZ [Ae] , 260 Peraluman-502 (Alusuisse) [Aw], 225
5
NF A-U10G [Ae], 260 Peraluman-70S (Alusuisse) [Aw], 225
NF A-U10S4 [Ae] , 260 Peraluman-S43 (Alusuisse) [Aw] , 225 S-65B (Brush Wellman) [Bw], 348
NF A-Z5G [Ae], 261 Peraluman-S45 (Alusuisse) [Aw], 225 S-200 (Brush Wellman) [Bw], 347
NF F100 [Ae], 282 Peraluman-S53 (Alusuisse) [Aw], 225 S-200F (Brush Wellman) [Bw], 348
NF F101 [Ae], 282 Peraluman-S60 (Alusuisse) [Aw], 225 S-200FC (Brush Wellman) [Bw], 348
NF F300 [Ae] , 282 Peraluman-S63 (Alusuisse) [Aw] , 225 S-200FH (Brush Wellman) [Bw], 348
NF G-A3Z1 [Me], 306 Peraluman-S75 (Alusuisse) [Aw], 226 SA2 (SABS) [Ae], 287
NF G-A6Z1 [Mw], 306 Perunal 205 (Alusuisse) [Aw], 226 SA4 (SABS) [Ae], 288
NF G-A7Z1 [Mw] , 306 Perunal215 (Alusuisse) [Aw], 226 SABS SA2 [Ae] , 287
NF G-ASZ [Mw], 306 Perunal 232 (Alusuisse) [Aw], 226 SABS SA4 [Ae], 288
NF G-A9 [Me], 306 Perunal 249 (Alusuisse) [Aw], 226 SCS-6/B-21S (Textron) [Tw], 335
NF G-A9Z1 [Me], 306 PF-60 (Brush Wellman) [Bw], 347 SCS-6/Ti-6-2-4-2 (Textron) [Tw], 335
NF G-Ag2.5TR [Me], 306 PR-200 (Brush Wellman) [Bw], 347 SCS-6/Ti-6-4 (Textron) [Tw], 335
NF G-Z4TR [Me], 306 PR-200E (Brush Wellman) [Bw], 347 SCS-6/Ti-6AI-15Nb-3Cr (Textron) [Tw], 335
NF G-Z5Zr [Mw], 306 Primary Grade (Ronald Britton & Co.) [Ap] , SCS-6/Ti-10AI-25Nb (Textron) [Tw], 335
NF T 40 [Te], 336 296 SCS-6/Ti-14-21 (Textron) [Tw], 335
NF TA 4DE [Tw], 336 Pure Aluminium 99.0 (Alusuisse) [Aw], 226
SCS-6/Ti-15-3-3-3 (Textron) [Tw], 335
NF TA 5E [Tw], 336 Pure Aluminium 99.5 (Alusuisse) [Aw], 227
SCS-9/Ti-6-4 (Textron) [Tw], 335
NF TA 5M [Tw], 336 Pure Aluminium 99.5 E (Alusuisse) [Aw] , 227
SCS-9/Ti-15-3-3-3 (Textron) [Tw], 336
NF TA6V [Tew], 336 Pure Aluminium 99.S (Alusuisse) [Aw], 227
Secondary Grade (Ronald Britton & Co.)
NF TA6V ELI [Tw], 336 Pure Aluminium 99.S5 (Alusuisse) [Aw] , 227 [Ap], 296
NF T-A6Zr5D [Tw], 337 Pure Aluminium 99.9 (Alusuisse) [Aw], 227 Secondary Purity (ALPOCO) [Ap], 296
NF Ti P64001 [Tw], 340 Pure Magnesium Ingot (Ayrton & Partners) SFS 2564 [Ae], 245
[Me],312
NF T-U2 [Tw], 344 SGAICu2NiMg (NBN) [Ae], 288
Pure Magnesium T-bars (Ayrton & Partners)
NF Unifont [Ae], 289 SGAICu4MgTi (NBN) [Ae] , 288
[Me],312
Silafont 36 (Valfond) [Ae] , 288
o Q
Silumin (VAW) [Ae], 288
Silumin-Beta (VAW) [Ae], 288
0-50 (Brush Wellman) [Bp], 347 Silumin-Delta (VAW) [Ae], 288
QE22A (ASTM) [Me], 312
Onorm G-AICu4Ti [Ae] , 282 Silumin-Kappa (VAW) [Ae] , 289
QH21A (ASTM) [Me], 313
Onorm G-AICu4TiMg [Ae] , 282 SIS 4020 [Ae] , 247
Otto Fuchs AM05 [Aw], 214 SIS 4021 [Ae] , 247
Otto Fuchs AM11 [Aw], 214 R SIS 4022 [Ae] , 247
Otto Fuchs AN50 [Aw], 215 SIS 4024 [Ae] , 247
R-2000 (Reynolds) [Aw], 227
Otto FuchsAS17 [Aw], 218 SP-65 (Brush Wellman) [Bp], 348
R54790 (UNS) [Tw], 334
Otto Fuchs AZ24 [Aw], 219 SP-200F (Brush Wellman) [Bp], 348
R56080 (UNS) [Tw], 334
Otto Fuchs AZ34 [Aw] , 219 SR-200 (Brush Wellman) [Bw], 349
R56210 (UNS) [Tw], 334
Otto Fuchs AZ67 [Aw], 219 SR-200E (Brush Wellman) [Bw], 349
R56260 (UNS) [Tw], 334
Otto Fuchs ES70 [Aw], 220 Standard (Ronald Britton & Co.) [Ap] , 296
R56740 (UNS) [Tw], 334
Otto Fuchs MA25 [Mw] , 308 Structural Laminates Co. ARALL 2 [Aw], 217
R58640 (UNS) [Tw], 335
Otto Fuchs TL 10 [Tw], 343 Structural Laminates Co. ARALL 3 [Aw], 217
R58820 (UNS) [Tw], 335
Otto Fuchs TL20 [Tw] , 343 Structural Laminates Co. Glare 1 [Aw], 221
R-81588 (MIL) [Tw], 334
Structural Laminates Co. Glare 2 [Aw], 221
Reflectal-050 (Alusuisse) [Aw], 227
p Structural Laminates Co. Glare 3 [Aw], 221
Reflectal-100 (Alusuisse) [Aw], 227
Structural Laminates Co. Glare 4 [Aw], 222
Relital (Alusuisse) [Aw] , 227
Pantal 5 (VAW) [Ae], 287 Structural Laminates Co. Glare 5 [Aw], 222
Remiral-050 (Alusuisse) [Aw], 228
Pantal 7 (VAW) [Ae], 287 Structural Laminates Co. Glare 5-F1 [Aw],
Remiral-100 (Alusuisse) [Aw] , 228 222
PE (ASTM) [Mw] , 312
Reynobond (Reynolds) [Aw], 228 Structural Laminates Co. Glare 5-F2 [Aw],
Peraluman-050 (Alusuisse) [Aw], 223
Reynolds 390 [Aw], 151 . 222
Peraluman-100 (Alusuisse) [Aw], 223
Reynolds MD209 [Aw], 222 Structural Laminates Co. Glare 5-FW [Aw],
Peraluman-101 (Alusuisse) [Aw], 223 222
Reynolds MD276 [Aw], 222
Peraluman 150 (Alusuisse) [Aw] , 223 Structural Laminates Co. Glare 6 [Aw], 222
Reynolds MD355 [Aw], 222
Peraluman 151 (Alusuisse) [Aw], 223
Reynolds MD356 [Aw], 223 Super Ink Lining (Ronald Britton & Co.) [Ap] ,
Peraluman 253 (Alusuisse) [Aw], 224 296
Reynolds R-2000 [Aw] , 227
Peraluman-226 (Alusuisse) [Aw], 223 Super Pure (ALPOCO) [Ap], 296
Reynolds Reynobond [Aw], 228
Peraluman-260 (Alusuisse) [Aw], 224 Superform Metals 5083 SPF [Aw], 179
Reynolds Tread-Brite [Aw], 228
Peraluman-300 [Aw], 224
(Alusuisse) Superform Metals Supral100 [Aw], 228
Reynolds Weldalite 049 [Aw], 229
Peraluman-301 [Aw], 224
(Alusuisse) Superform Metals Supral 150 [Aw], 228
RIMA AZ91 C [Me], 303
Peraluman-302 [Aw], 224
(Alusuisse) Supral100 (Superform Metals) [Aw], 228
RIMA AZ91 HP [Me], 303
Peraluman-410 [Aw], 224
(Alusuisse) Supral 150 (Superform Metals) [Aw], 228
RIMA MG Metal [Me], 311
Peraluman-412 (Alusuisse)
[Aw], 224
Peraluman-460 [Aw], 225
(Alusuisse)
Peraluman-462 (Alusuisse) [Aw] , 225
Peraluman-470 (Alusuisse) [Aw], 225
524 Index of Alloy Names and Designations
T Ti-8Mo-8V-2Fe-3AI [Twl, 338 Timminco AZ31 [Mewl, 301
Ti-10-2-3 (Titanium Industries) [Twl, 338 Timminco AZ63 [Mel, 302
T 40 (NF) [Te], 336 Ti-10V-2Fe-3AI 0 [Tw], 338 Timminco AZ91 UX [Mel, 304
2TA1 (BS) [Tw], 317 Ti-10V-2Fe-3AI [Tw], 338 Timminco AZ91 X [Mel, 304
2TA10 (BS) [Tw], 317 Ti-13V-11Cr-3AI 0 [Tw], 339 Timminco AZ92 [Me], 304
2TA21 (BS) [Tw], 317 Ti-13V-11Cr-3AI [Twl, 339 Timminco High Purity Magnesium [Mewl,
TA 4DE (NF) [Tw], 336 Ti-15-3 (-) [Tw], 339 307
TA 5E (NF) [Tw], 336 Ti-15-3 (Titanium Industries) [Twl, 339 Timminco M-1 Hi-Potential [Mew], 308
TA 5M (NF) [Tw], 336 Ti-15-3 [Twl, 339 Timminco MAG-CAL [Mc], 308
TA6V (NF) [Tew], 336 Ti-64 (Titanium IntI.) [Twl, 339 Titanal (AMAG) [Awl, 228
TA6V ELI (NF) [Tw], 336 Ti-6242 (-) [Tw], 339 Titanium Industries GR-1 [Twl, 331
T-A6Zr5D (NF) [Tw], 337 Ti-6242S (-) [Tewl, 339 Titanium Industries GR-2 [Tewl. 331
2TA10 (BS) [Tw], 317 Tikrutan LT 24 (Deutsche Titan) [Twl, 341 Titanium Industries GR-3 [Tcw], 331
TA18 (BS) [Tw], 337 Tikrutan LT 25 (Deutsche Titan) [Tw], 341 Titanium Industries GR-4 [Tew], 331
TA20 (BS) [Tw], 337 Tikrutan LT 26 (Deutsche Titan) [Tw], 341 Titanium Industries GR-5 [Tew], 331
2TA21 (BS) [Tw], 317 Tikrutan LT 27 (Deutsche Titan) [Tewl, 342 Titanium Industries GR-7 [Tew], 332
TA45 (BS) [Tw], 337 Tikrutan LT 31 (Deutsche Titan) [Twl, 342 Titanium Industries GR-12 [Tw], 331
Teledyne Allvac 3-2.5 [Twl, 328 Tikrutan LT 33 (Deutsche Titan) [Twl, 342 Titanium Industries Ti-4-4-2.5 (550) [Twl,
Tikrutan LT 34 (Deutsche Titan) [Twl, 342 338
Teledyne Allvac 5-2.5 [Twl, 328
Tikrutan LT 35 (Deutsche Titan) [Twl, 342 Titanium Industries Ti-6-2-4-2 [Twl, 338
Teledyne Allvac 6-2-4-2 [Twl, 328
Tikrutan RT 12 (Deutsche Titan) [Twl, 342 Titanium Industries Ti-6-2-4-6 [TwJ, 338
Teledyne Allvac 6-2-4-6 [Twl, 329
Tikrutan RT 12 Pd (Deutsche Titan) [Tw], Titanium Industries Ti-1 0-2-3 [Twl, 338
Teledyne Allvac 6-4 [Tw], 329
343 Titanium Industries Ti-15-3 [Twl, 339
Teledyne Allvac 6-4 ELI [Twl, 329
Tikrutan RT 15 (Deutsche Titan) [Twl, 343 Titanium IntI. Ti-1 [Tw], 337
Teledyne Allvac 6-6-2 [Twl, 329
Tikrutan RT 15 Pd (Deutsche Titan) [Twl, Titanium IntI. Ti-2 [Twl, 337
Teledyne Allvac 6-7 [Twl, 329
343 Titanium IntI. Ti-3 [Twl, 337
Teledyne Allvac 8-1-1 [Tw], 329
Tikrutan RT 18 (Deutsche Titan) [Twl, 343 Titanium IntI. Ti-4 [Twl, 337
Teledyne Allvac 30 [Twl, 329
Tikrutan RT 18 Pd (Deutsche Titan) [Twl, Titanium IntI. Ti-7 [Twl, 338
Teledyne Allvac 40 [Twl, 329 343 Titanium IntI. Ti-64 [Twl, 339
Teledyne Allvac 40+Pd [Twl, 329 Tikrutan RT 20 (Deutsche Titan) [Twl, 343 Titanium/Aluminium (Goodfellow) [Tp], 343
Teledyne Allvac 50 [Twl, 329 Ti-Metacs TM6 (TYK) [Awl, 340 TL 10 (Otto Fuchs) [Tw], 343
Teledyne Allvac 55 [Twl, 329 Ti-Metacs TS7 (TYK) [Aw], 340 TL20 (Otto Fuchs) [Twl, 343
Teledyne Allvac 70 [Twl, 329 TimetaI3-2.5 [Tw], 318 Toyal Europe 404N [Apl, 295
Textron SCS-6/B-21S [Twl, 335 Timetal 6-2-4-2 [Twl, 321 Toyal Europe 405 [Apl, 295
Textron SCS-6fTi-6-2-4-2 [Twl, 335 Timetal 6-2-4-6 [Twl, 321 Toyal Europe 406S [Apl, 295
Textron SCS-6/Ti-6-4 [Twl, 335 Timetal6-4 [Tew], 321 Toyal Europe 416 [Apl, 295
Textron SCS-6fTi-6AI-15Nb-3Cr [Tw], 335 Timetal 6-6-2 [Tw], 321 Toyal Europe 432S [Apl, 295
Textron SCS-6fTi-10AI-25Nb [Twl, 335 TimetaI8-1-1 [Tw], 322 Toyal Europe 455 [Ap], 295
Textron SCS-6fTi-14-21 [Twl, 335 TimetaI10-2-3 [Twl, 322 Toyal Europe 462 [Apl, 295
Textron SCS-6fTi-15-3-3-3 [Twl, 335 Timetal 15-3 [Twl, 322 Transage 129 [Twl, 323
Textron SCS-9fTi-6-4 [Twl, 335 Timetal17 [Tew], 322 Transage 134 [Twl, 323
Textron SCS-9fTi-15-3-3-3 [Twl, 336 Timetal 21 S [Tw], 322 Transage 175 [Tw], 324
Ti 17 (-) [Twl, 339 Timetal 21 SRx [Twl, 322 Tread-Brite (Reynolds) [Awl, 228
Ti AI6 V4 (DIN) [Twl. 339 Timetal 35A [Tw], 322 T-U2 (NF) [Twl, 344
Ti P62 (AECMA) [Tw], 340 Timetal 50A [Tew], 323 TYK Metacs 20 [Aewl, 223, 287
Ti P63 (CEN) [Twl, 340 Timetal 62S [Tw], 323 TYK Ti-Metacs TM6 [Awl, 340
Ti P9001 (AECMA) [Twl, 340 Timetal 65A [Tew], 323 TYK Ti-Metacs TS7 [Awl, 340
Ti P64001 (NF) [Twl, 340 Timetal75A [Tw], 323
Ti P99001 (CEN) [Tw], 341
Ti P99002 (CEN) [Tw],1341
Timetal100A [Tew], 323
Timetal 230 [Twl, 324
u
Ti P99003 (CEN) [Tw], 341 Timetal 367 [Twl, 324 UNE L-2640 [Ae], 284
Ti-1 (Titanium IntI.) [Twl, 337 Timetal 550 [Twl, 324 UNI 3040 [Ael, 245
Ti-2 (Titanium IntI.) [Twl, 337 Timetal 551 [Twl, 325 UNI 3041 [Ael, 245
Ti-3 (Titanium IntI.) [Twl, 337 Timetal 679 [Twl, 325 UNI 3042 [Ael, 245
Ti-3AI-2.5V (-) [Twl, 337 Timetal685 [Twl, 325 UNI 3043 [Ael, 246
Ti-4 (Titanium IntI.) [Twl, 337 Timetal 829 [Twl, 326 UNI 3044 [Ael, 246
Ti-4-4-2.5 (550) (Titanium Industries) [Twl, Timetal 834 [Twl, 326
338 UNI 3045 [Ae], 246
Timetal1000 [Twl, 326 UNI 3046 [Ae], 246
Ti-6-2-4-2 (Titanium Industries) [Twl, 338
Timetal11 00 [Twl, 326 UNI 3048 [Ae], 246
Ti-6-2-4-6 (Titanium Industries) [Twl, 338
Timetal 5111 [Twl, 328 UNI 3049 [Ae], 246
Ti-6AI-2Sn-2Zr-2Cr-Mo 0 [Tw], 338
Timetal Code 12 [Tewl, 331 UNI 3050 [Ae], 246
Ti-6AI-2Sn-2Zr-2Cr-Mo [Tw], 338
Timetal LCB [Twl, 334 UNI 3051 [Ae], 246
Ti-7 (Titanium IntI.) [Twl, 338
Timminco 420 [Aewl, 151, 241 UNI 3052 [Ae], 246
Ti-8AI-1Mo-1V 0 [Twl, 338
Timminco AM60SX [Me], 299 UNI 3054 [Ae], 246
Ti-8AI-1 Mo-1 V [Twl, 338
Timminco AM60X [Mel, 299 UNI 3055 [Ae], 246
Ti-8Mo-8V-2Fe-3AIO [Tw], 338
Timminco AM80 [Me], 299
Index of Alloy Names and Designations 525
UNI 3056 [Ac], 246 YAW Silumin-Delta [Ac], 288
UNI 3057 [Ac] , 246 YAW Silumin-Kappa [Ac] , 289
w
UNI 3058 [Ac], 246 YAW Veral 99.5 [Ac] , 289 WE43A (ASTM) [Mcw] , 313
UNI 3059 [Ac], 247 YAW Veral 99.7 [Ac] , 289 WE54A (ASTM) [Mcw], 313
UNI 3599 [Ac], 247 YAW Veral 100 [Ac] , 289 Weldalite 049 (Reynolds) [Aw], 229
UNi 3600 [Ac], 247 YAW Veral 100G [Ac], 289 Wk. 30255 (AI99.5) (DIN) [Aw], 143
UNI 3601 [Ac], 247 YAW Veral 225 [Ac], 290 Wk. 3.0257 (E-AI) (DIN) [Aw] , 143
UNI 3602 [Ac], 247 YAW VeraI226(D) [Ac], 290 Wk. 3.0285 (AI99.8) (DIN) [Aw], 143
UNI 4513 [Ac], 248 VAW Veral 226A [Ac], 290 Wk. 3.0305 (AI99.9) (DIN) [Aw], 143
UNI 4514 [Ac] , 248 VAW Veral 231 (D) [Ac], 290 Wk. 3.0315 (AIMn1) (DIN) [Aw], 143
UNI 5074-74 [Ac], 248 YAW Veral 231A [Ac], 290 Wk. 3.0385 (AI99.98R) (DIN) [Aw], 144
UNI 5075-74 [Ac], 248 VAW Veral 233 [Ac] , 290 Wk. 3.0400 (DIN) [Aw], 144
UNI 5076-74 [Ac], 248 VAWVeral241 [Ac] , 291 Wk. 30915 (AIFeSi) (DIN) [Aw], 144
UNI 5077-74 [Ac] , 248 VAW Veral Cu4Ti [Ac], 291 Wk. 3.1255 (AICuSiMn) (DIN) [Aw], 144
UNI 5079-74 [Ac], 248 YAW Veral Cu4TiMg [Ac], 291 Wk. 3.1305 (AICu2.5Mg05) (DIN) [Aw], 144
UNI 5080-74 [Ac], 248 VAW Veral Mg3 [Ac], 291 Wk. 3.1325 (AICuMg1) (DIN) [Aw], 144
UNI 6250-68 [Ac], 248 YAW Veral Mg3(H) [Ac], 291 Wk. 3.1355 (AICuMg2) (DIN) [Aw], 144
UNI 6251-68 [Ac] , 249 YAW Veral Mg3Si(H) [Ac], 292 Wk. 3.1855 (AICuBiPb) (DIN) [Aw], 145
UNI 6252-68 [Ac], 249 YAW Veral Mg5(H) [Ac], 292 Wk. 3.2305 (AIMgSi) (DIN) [Aw], 145
UNI 6253-68 [Ac], 249 VAW Veral Mg5Si(H) [Ac], 292 Wk. 3.2315 (AIMgSi1) (DIN) [Aw], 145
UNI 7257 [Ac], 249 YAW Veral Mg9 [Ac], 292 Wk. 3.3206 (AIMgSiO.5) (DIN) [Aw], 145
UNI 7363 [Ac] , 249 YAW Veral Mg9(H) [Ac] , 292 Wk. 3.3208 (AI99.9MgSi) (DIN) [Aw], 145
UNI 7369-74 Part 1 [Ac], 249 YAW Veral Mg10(H) [Ac], 292 Wk. 3.3211 (AIMg1 SiCu) (DIN) [Aw], 145
UNI 7369-74 Part 2 [Ac], 249 YAW Veral Si5MgA [Ac], 293 Wk 3.3308 (AI99.9MgO.5) (DIN) [Aw], 146
UNI 7369-74 Part 3 [Ac], 249 YAW Veral Si1 OMg(D) [Ac], 293 Wk. 3.3309 (DIN) [Aw], 146
UNI 7369-74 Part 4 [Ac], 249 VAW Veral Si1 OMgA [Ac], 293 Wk. 3.3315 (AIMg1) (DIN) [Aw], 146
UNI 7369-74 Part 5 [Ac], 249 YAW Veral Si12A [Ac], 293 Wk. 3.3318 (AI99.9Mg1) (DIN) [Aw], 146
UNI 7369-74 Part 6 [Ac], 249 YAW Veral Si12A(D) [Ac], 293 Wk. 3.3318 (DIN) [Aw], 146
UNI 7963 [Ac], 249 VAW Veral Si12CuNiMg [Ac], 294 Wk. 3.3319 (DIN) [Aw], 146
UNI 8024 [Ac] , 250 YAW Veral Si12CuNiMg(H) [Ac], 294 Wk. 3.3326 (AIMg1.8) (DIN) [Aw], 146
Unidal (Alusuisse) [Aw], 228 YAW Veral Si17Cu4Mg(H) [Ac], 294 Wk. 3.3523 (AIMg2.5) (DIN) [Aw], 146
Unidur 091 (Alusuisse) [Aw], 229 VAW Veral Si18CuNiMg(H) [Ac], 294 Wk. 3.3526 (AIMg2MnO.3) (DIN) [Aw], 146
Unidur 102 (Alusuisse) [Aw], 229 YAW Veral Zn1 OSi8CuMg [Ac], 294 Wk. 3.3535 (AIMg3) (DIN) [Aw], 147
Unidur 120 (Alusuisse) [Aw], 229 Veral 99.5 (VAW) [Ac], 289 Wk. 3.3555 (AIMg5) (DIN) [Aw], 147
Unifont (NF) [Ac], 289 Veral 99.7 (VAW) [Ac], 289 Wk. 3.4335 (AIZn4.5Mg1) (DIN) [Aw], 147
UNS M14142 [M], 308 Veral 100 (VAW) [Ac], 289 Wk. 3.4365 (AIZnMgCu15) (DIN) [Aw], 147
UNS R54790 [Tw], 334 Veral100G (VAW) [Ac] , 289 Wk. 3.5003 (DIN) [Mw], 297
UNS R56080 [Tw], 334 Veral 225 (VAW) [Ac], 290 Wk. 3.5101 [Mc], 297
(DIN)
UNS R5621 0 [Tw], 334 Veral 226(0) (VAW) [Ac] , 290 Wk. 3.5103 [Mc] , 297
(DIN)
UNS R56260 [Tw], 334 Veral 226A (VAW) [Ac], 290 Wk. 3.5161 [Mw] , 297
(DIN)
UNS R56740 [Tw], 334 VeraI231(D) (VAW) [Ac], 290 Wk. 3.5812 [Mc] , 297
(DIN)
UNS R58640 [Tw], 335 Veral231A (VAW) [Ac], 290 Wk. 3.5912 [Mc] , 297
(DIN)
UNS R58820 [Tw], 335 Veral 233 (VAW) [Ac], 290 Wk. 3.7025 [Tw], 318
(DIN)
Veral241 (VAW) [Ac], 291 Wk. 3.7035 [Tw], 318
(DIN)
v Veral Cu4Ti (VAW) [Ac] , 291 Wk. 3.7055 [Tw], 318
(DIN)
Veral Cu4TiMg (VAW) [Ac], 291 Wk. 3.7065 [Tw], 318
(DIN)
Valfond A-S 17U4G [Ac], 259 Veral Mg3 (VAW) [Ac], 291 Wk. 3.7105 [Tcw], 318
(DIN)
Valfond Silafont 36 [Ac], 288 Veral Mg3(H) (VAW) [Ac], 291 Wk. 3.7110 [Tw], 318
(DIN)
YAW 41104 [Aw], 147 Veral Mg3Si(H) (VAW) [Ac] , 292 Wk. 3.7115 [Tw], 318
(DIN)
YAW 41/20 [Aw], 148 Veral Mg5(H) (VAW) [Ac], 292 Wk. 3.7145 [Tw], 319
(DIN)
YAW 61/03 [Aw], 148 Veral Mg5Si(H) (VAW) [Ac], 292 Wk. 3.7155 [Tw], 319
(DIN)
VAW61/10[Aw], 148 Veral Mg9 (VAW) [Ac], 292 Wk. 3.7165 [Tw], 320
(DIN)
YAW 61/15 [Aw], 148 Veral Mg9(H) (VAW) [Ac], 292 Wk. 37175 [Tw], 320
(DIN)
YAW 63/37 [Aw], 148 Veral Mg10(H) (VAW) [Ac], 292 Wk. 3.7185 [Tw], 320
(DIN)
YAW 63/45 [Aw], 148 Veral Si5MgA (VAW) [Ac], 293 Wk. 3.7225 [Tw], 320
(DIN)
YAW 63/52 [Aw], 148 Veral Si10Mg(D) (VAW) [Ac], 293 Wk. 3.7235 (DIN) [Tw], 321
YAW 98/50 [Aw], 149 Veral Si10MgA (VAW) [Ac], 293 Wk. 3.7255 (DIN) [Tw], 321
YAW 99/00 [Aw], 149 Veral Si12A (VAW) [Ac] , 293
Si12A(D) (VAW) [Ac], 293
YAW 99/01 [Aw], 149
YAW 99/52 [Aw], 149
Veral
Veral Si12CuNiMg (VAW) [Ac], 294
x
YAW Autodur [Ac] , 276 Veral Si12CuNiMg(H) (VAW) [Ac], 294 X2096 (AA) [Aw], 229
YAW Pantal 5 [Ac], 287 Veral Si17Cu4Mg(H) (VAW) [Ac], 294 X2119 (AA) [Aw], 229
YAW Pantal 7 [Ac], 287 Veral Si18CuNiMg(H) (VAW) [Ac], 294 X2316 (AA) [Aw], 229
yAW Silumin [Ac] , 288 Veral Zn10Si8CuMg (VAW) [Ac], 294 X3030 (AA) [Aw], 229
YAW Silumin-Beta [Ac], 288 VT51 (-) [Tw], 344 X4003 (AA) [Aw], 229
526 Index of Alloy Names and Designations
X4005 [Aw], 229
(AA)
X5002 [Aw], 229
(AA)
X5012 [Aw], 229
(AA)
X5015 [Aw], 229
(AA)
X5020 [Aw], 230
(AA)
X5055 [Aw], 230
(AA)
X5058 [Aw], 230
(AA)
X5080 [Aw], 230
(AA)
X5084 [Aw], 230
(AA)
X5090 [Aw], 230
(AA)
X5153 [Aw], 230
(AA)
X5184 [Aw], 230
(AA)
X5452 [Aw], 230
(AA)
X6030 [Aw], 230
(AA)
X6064 [Aw], 230
(AA)
X6067 [Aw], 230
(AA)
X6161 [Aw], 230
(AA)
X6163 [Aw], 230
(AA)
X6251 [Aw], 230
(AA)
X7006 [Aw], 230
(AA)
X7007 [Aw], 230
(AA)
X7038 [Aw], 230
(AA)
X7040 [Aw], 231
(AA)
X7080 [Aw], 231
(AA)
X7106 [Aw], 231
(AA)
X7272 [Aw], 231
(AA)
X7275 [Aw], 231
(AA)
X7279 (AA) [Aw], 231
X8002 (AA) [Aw], 231
X8003 (AA) [Aw], 231
X8090A (AA) [Aw], 231
X8092 (AA) [Aw], 231
X8192 (AA) [Aw], 231
X8380 (AA) [Aw], 231
X8480 (AA) [Aw], 231
z
ZC63A (ASTM) [Me], 313
ZC71 (ASTM) [Mw], 313
ZC71 (Magnesium Elektron) [Mw], 313
ZC71A (ASTM) [Mew], 314
ZE41A (ASTM) [Me], 314
ZE63A (ASTM) [Me], 314
ZH62A (ASTM) [Me], 314
ZK21A (ASTM) [Mw], 314
ZK40A [Mw], 314
(ASTM)
ZK51A [Me], 314
(ASTM)
ZK60A [Mw], 315
(ASTM)
ZK61A [Me], 315
(ASTM)
ZM21 (ASTM) [Mw], 315
ZTY (Magnesium Elektron) [Mw], 315
ZW3 (Magnesium Elektron) [Mw], ~15
COMMENTS & CONTRIBUTIONS FOR THE NEXT EDITION OF
THE LIGHT ALLOYS DIRECTORY & DATA BOOK
Comments
We are very interested to know your comments and suggestions on the content and structure of this first edition of the book.
Readership feed-back is an essential part of the revision process. Please use the form provided (next page) to contact the
authors of this book - Thank you.
Contributions
To ensure that this publication remains up-to-date, we shall be revising its contents periodically. We welcome information
from new companies, data on new products, changes to existing products or revised company information (address,
telephone, fax, etc). Inclusion is free. It does not cost anything for your company's information to be included and it will not
be sold on or used for marketing purposes. Please complete this form (print clearly) and send it with the new information.
D We have contributed information for this edition of the book. We wish to notify you of:
o Change of name or address or telephone numbers,
D New products available,
D Products no longer available or replaced by new products,
D Products listed now have changed properties,
D Error in data (please specify precisely the nature of the error),
Please send BY POST full TECHNICAL DA TA SHEETS on the properties and characteristics of light alloys,
D We have not previously provided data, but now wish to contribute to the next edition of this book. We
manufacture or supply Light Alloys which can be added into the following sections of this book (please tick all
those relevant and send this completed page with the data sheets):
o Aluminium - wrought D Titanium
D Aluminium - cast D Composites
D Aluminium - powder D Hybrid metal-polymer materials
o Magnesium (please give details)
Provide as much product detail as possible:
Product name/code
Composition
Product forms: casting (ingot, cast method), wrought (state processing method, e,g, extruded, drawn, forged, etc),
Similar/Equivalent alloys (within American, European and national systems, including aerospace or other industry-
specific designation systems)
Comments relating to the type, use and any particular features of the material.
Typical mechanical properties (for product form and tempers available): Yield, proof, tensile strengths, modulus,
hardness including any appropriate test method notes,
Send BY POST full TECHNICAL DATA SHEETS on the properties and characteristics of each product
D We are suppliersldistributors for (please state your company details and manufacturers' names, and send
a letter-heading or business card)
D COMPANY INFORMATION: A list of updated contact addresses (with a contact name if possible), telephone, fax,
telex, E-mail numbers for all subsidiaries/offices across the world, Also state Internet site addresses,
D PERMISSION Please indicate your agreement to reproduce any data provided in the directory & data book,
D ADVERTISING: Please indicate your interest in placing an advertisement in this book, There is no obligation,
Please send this completed page with your contributions by post (not by fax) to:
RJ Technical Consultants
Bois Moreau
F-17770 JUICQ
Charente Maritime
FRANCE
All queries should be addressed to either Bob Hussey or Jo Wilson (Tel/Fax: +33546953510), Sorry, we cannot accept
information sent by fax as numerical data can often be difficult to read with any confidence,