Escolar Documentos
Profissional Documentos
Cultura Documentos
Introduction
Gate Valve
Gate valve, also know as sluice valve, is a valve that opens by lifting a round
wedge out of the path of a fluid. The distinct feature of a gate valve is the
sealing surfaces between the gate and seats are planar, so gate valves are
often used when a straight-line flow of fluid and minimum restriction is desired.
Typical gate valves should never be used for regulating flow, unless they are
specially designed for that pur pose.
Globe Valve
Globe valve is a type of valve used in regulating flow in a pipeline, consisting of
a movable disk-type element and a stationar y ring seat in a generally spherical
body.
Glove valves are widely used for application require throttling and frequent
operation. Since the baffle of the globe valves restrict flow, it is not
recommended where full and unobstructed flow is required.
Check Valve
Check valve / Non- retur n valve is a mechanical device which nor mally allows
fluid to flow through it in one direction.
Check valve has two openings in the body, one for fluid to enter and the other for
fluid to leave. It works automatically and exter nal control is not required.
Although check valves are offered in a wide range of size, they are generally
small and simple.
Butterfly Valve
Butterfly valve is usually used for regulating and isolating flow. The closing
mechanism takes the for m of a disc which allows quick shut off.
The valves disc is positioned in the centre of the pipe, passing through the disc
is a rod connected to an actuator on the outside of the valve. Rotating the
actuator tur ns the disc either parallel or per pendicular to the flow.
Y-Strainer
Y-Strainer takes the name for its configuration. It is intended to be used for
applications where small amounts of solid par ticulate are expected, and where
clean-out will be infrequent.
Y-Strainer allows clean-out without removal of the screen and interrupting the
process flow.
The Y-end of the Y strainer must be below the pipeline, pointing down, to trap the
debris.
Bucket Strainer
Same as Y-Strainer, Bucket Strainer is also used for trapping debris.
Bucket Strainer provides a larger screen compared with Y-Strainer. It also has a
cap on the top which can be easily removed to clean or replace the gasket.
SK-I
Gate valves are designed for ser vices that require infrequent operation. The disc is kept either
fully opened or fully closed. It is not recommended for regulating flow pur pose.
Specification:
The gate valves are manufactured in accordance with BS E N 1171, testing under BS E N 12266.
Pressure Rating: P N 16
Hydraulic test to BS EN12266
Seat: 17.6 Bar Body: 24 Bar
Operator: Handwheel
Protective Coating: Epoxy coating applied inter nally, approved for potable water
ser vice to B S 6920
Materials:
Parts Materials
Body, Disc, Cap, Stem, Bolt, Eye
Bolt, Nut, Eye But, Gland, Hinge Stainless steel BS E N 10088 S S 316
Pin, Spring Washers, Name Plate
Component List:
13 12
14 11
15 10
16 9
17 8
18 7
16 6
19 5
4
3
2
1
Dimensions:
Size
L H W D C N - M
DN NPS
15 1/2 108 182 120 95 65 4 - 14
20 3/4 117 195 120 105 75 4 - 14
25 1 127 237 120 115 85 4 - 14
32 1 1/4 140 294 200 140 100 4 - 18
40 1 1/2 165 294 200 150 110 4 - 18
50 2 178 335 200 165 125 4 - 18
65 2 1/2 190 393 200 185 145 4 - 18
80 3 203 467 250 200 160 8 - 18
100 4 229 549 250 220 180 8 - 18
150 6 267 743 300 285 240 8 - 22
200 8 292 910 350 340 295 12 - 22
250 10 330 1097 400 405 355 12 - 26
300 12 356 1285 400 460 410 12 - 26
SK-I
Specification:
The globe valves are manufactured in accordance with BS E N 1 3789 , testing under BS E N 12266.
Pressure Rating: P N 16
Hydraulic test to BS EN12266
Seat: 17.6 Bar Body: 24 Bar
Thread Connection: B S 21
Operator : Handwheel
Protective Coating: Epoxy coating applied inter nally, approved for potable water
ser vice to B S 6920
Materials:
Parts Materials
Component List:
1. Body 7. Gland
2. Disc 8. Cap Nut
3. Cap 9. Stem
4. Gasket 10. Handle
5. Whorl Gasket 11. Name Plate
6. Packing 12. Nut
12
11
10
9
8
7
6
5
4
3
2
1
Dimensions:
Size
L H H1 W
DN NPS
8 1/4 52 89 99 70
10 3/8 52 89 99 70
15 1/2 52 89 99 70
20 3/4 66 95 107 80
25 1 76 102 118 80
32 1 1/4 86 130 150 90
40 1 1/2 94 132 152 90
50 2 118 151 166 100
SK-I
Specification:
The globe valves are manufactured in accordance with BS E N 1 3789 , testing under BS E N 12266.
Pressure Rating: P N 16
Hydraulic test to BS EN12266
Seat: 17.6 Bar Body: 24 Bar
Operator: Handwheel
Protective Coating: Epoxy coating applied inter nally, approved for potable water
ser vice to B S 6920
Materials:
Parts Materials
Body, Disc, Disc Cover, Cap, Stem,
Bolt, Eye Bolt, Nut, Gland, Hinge Stainless steel BS E N 10088 S S 316
Pin, Spring Washers, Name Plate
Component List:
17
15
16
14
13
12
11
18
10 19
9
20 14"& Larger
8
7
6
5
4
3
2
1
Dimensions:
Size
L H W D C N - M
DN NPS
15 1/2 108 178 140 95 65 4 - 14
20 3/4 117 181 140 105 75 4 - 14
25 1 127 200 140 115 85 4 - 14
32 1 1/4 140 243 160 140 100 4 - 18
40 1 1/2 165 245 160 150 110 4 - 18
50 2 203 258 200 165 125 4 - 18
65 2 1/2 216 310 200 185 145 4 - 18
80 3 241 325 250 200 160 8 - 18
100 4 292 390 250 220 180 8 - 18
150 6 356 531 350 285 240 8 - 22
200 8 495 669 350 340 295 12 - 22
250 10 622 824 500 405 355 12 - 26
300 12 698 979 500 460 410 12 - 26
350 14 787 1230 600 520 470 16 - 26
SK-I
Specification:
The butterfly val ves are manufactured in accordance with BS E N593 , testing under BS E N 12266.
Pressure Rating: P N 16
Hydraulic test to BS E N 12266
Seat: 17.6 Bar Body: 24 Bar
Protective Coating: Epoxy coating applied inter nally, approved for potable water
ser vice to B S 6920
*According to En593 Clause 4.1.4.1, face to face dimension for DN lower than those defined in EN558-1 shall
be specified by the manufacturer.
Materials:
Parts Materials
Seat EPDM
SK-I
Component List:
1. Body 3. Seat
2. Seat 4. Lever Handle
4
L2
L1
1
2
3
Dimensions:
DN 32 L1 65
Size Body
NPS 1 1/4 L2 130
SK-I
Specification:
The butterfly val ves are manufactured in accordance with BS E N593 , testing under BS E N 12266.
Pressure Rating: P N 16
Hydraulic test to BS E N 12266
Seat: 17.6 Bar Body: 24 Bar
Protective Coating: Epoxy coating applied inter nally, approved for potable water
ser vice to B S 6920
Materials:
Parts Materials
Seat EPDM
SK-I
Component List:
OPEN
L
CLOSE
7
P
8
P
9
4
L2 L2
HOLE NO HOLE NO: HOLE NO:
5
L1
L1 L1
Dimensions:
DN 40 50 65 80 100 150 200 250 300 350 400 450 500 600
Size
NPS 1 1/2 2 2 1/2 3 4 6 8 10 12 14 16 18 20 24
L1 55 66 73 79 108 138 178 200 228 268 307 335 381 457
Body Hole No 2 2 2 2 4 4 4 4 4 4 4 4 4 4
L 38 43 46 46 52 56 60 68 78 78 102 114 127 154
L2 135 150 150 163 182 226 256 286 339
Lever
P 220 220 220 220 220 256 350 350 350
L2 136 152 157 165 182 226 256 288 343 402 412 432 510 600
Worm
P 170 170 170 170 183 183 260 260 260 270 270 270 300 300
Gear
H 152 152 152 152 152 152 245 245 245 325 325 325 385 385
Electric
O O O O O O O O O O O O
Actuator
SK-I
Specification:
The wafer type check val ves are manufactured in accordance with BS E N12334 , testing under
BS E N 12266.
Pressure Rating: P N 16
Hydraulic test to BS E N 12266
Seat: 17.6 Bar Body: 24 Bar
Protective Coating: Epoxy coating applied inter nally, approved for potable water
ser vice to B S 6920
Materials:
Parts Materials
Seat EPDM
SK-I
Component List:
1. Body 6. Retainer
2. Plate 7. Body Bearing
3. Spring 8. Plate Bearing
4. Hinge Pin 9. Seat
5. Stop Pin 10. Eye Bolt
A A
FLOW
50,4
? 61
? 36 ,8
Dimensions:
Size
A B E
DN NPS
40 1 1/2 92 60 33
50 2 105 60 43
65 2 1/2 124 73 46
80 3 137 89 64
100 4 156 114 64
150 6 217 168 76
200 8 267 219 89
250 10 330 274 114
300 12 375 324 114
350 14 438 406 127
400 16 495 420 140
SK-I
Specification:
The flanged end check valves are manufactured in accordance with BS EN 12334, tested under
BS EN12266, flanged ends manufactured in accordance with BS EN 1092-1.
Pressure Rating: P N 16
Hydraulic test to BS EN12266
Body: 24 Bar
Materials:
Parts Materials
Gasket PTFE
SK-I
Component List:
1. Body 6. Gasket
2. Disc 7. Bolt
3. Nut 8. Bonnet
4. Arm Hinge 9. Bolt
5. Hinge Pin
Dimensions:
Size
L D H G T C N - M
DN NPS
15 1/2 108 95 51 46 14 65 4 - 14
20 3/4 117 105 54 56 16 75 4 - 14
25 1 127 115 64 65 16 85 4 - 14
32 1 1/4 140 140 68 76 18 100 4 - 18
40 1 1/2 165 150 75 84 18 110 4 - 18
50 2 203 165 97 99 20 125 4 - 18
65 2 1/2 216 185 111 118 20 145 4 - 18
80 3 241 200 120 132 20 160 8 - 18
100 4 292 220 162 156 22 180 8 - 18
150 6 356 285 203 211 24 240 8 - 22
200 8 495 340 236 266 24 295 12 - 22
SK-I
Specification:
The Y-Strainers are tested under BS E N 12266 , screwed end manufactured according to BS21 .
Pressure Rating: P N 16
Hydraulic test to BS EN12266
Body: 24 Bar
Materials:
Parts Materials
Gasket PTFE
SK-I
Component List:
1. Body 4. Cap
2. Screen 5. Stopper
3. Gasket 6. Gasket
6 5 4 3 2 1
Dimensions:
Size
L H D
DN NPS
15 1/2 65 45 31
20 3/4 80 53 36
25 1 90 68 45
32 1 1/4 105 71.5 50
40 1 1/2 120 80 59
50 2 140 97 75
65 2 1/2 170 112 95.4
80 3 195 129 111
SK-I
Specification:
The Y-Strainers are tested under BS EN12266, flanged ends manufactured in accordance with
BS EN 1092-1.
Pressure Rating: P N 16
Hydraulic test to BS EN12266
Body: 24 Bar
Materials:
Parts Materials
Gasket* PTFE
Component List:
1. Body 5. Gasket
2. Screen 6. Stopper
3. Gasket 7. Spring Washers
4. Bonnet 8. Bonnet Bolt
1
2
3
4
5
6
7
8
Dimensions:
Size
L D C N - M
DN NPS
15 1/2 120 95 65 4 - 14
20 3/4 140 105 75 4 - 14
25 1 150 115 85 4 - 14
32 1 1/4 180 140 100 4 - 18
40 1 1/2 190 150 110 4 - 18
50 2 210 165 125 4 - 18
65 2 1/2 250 185 145 4 - 18
80 3 280 200 160 8 - 18
100 4 340 220 180 8 - 18
150 6 420 285 240 8 - 22
200 8 500 340 295 12 - 22
350 14 700 520 470 16 - 26
400 16 780 580 525 16 - 30
SK-I
Specification:
The Bucket Strainers are tested under BS E N 12266, flanged ends manufactured in accordance
with BS E N1092-1.
Pressure Rating: P N 16
Hydraulic test to BS EN 12266
Body: 24 Bar
Materials:
Parts Materials
Gasket PTFE
SK-I
Component List:
6
5
4
3
2
1
Dimensions:
Size
L H H1 D C N - M
DN NPS
50 2 260 127 136 165 125 4 - 18
65 2 1/2 330 135 150 185 145 4 - 18
80 3 340 165 163 200 160 8 - 18
100 4 400 203 191 220 180 8 - 18
150 6 500 219 208 285 240 8 - 22
200 8 560 298 250 340 295 12 - 22
250 10 660 349 288 405 355 12 - 26