Escolar Documentos
Profissional Documentos
Cultura Documentos
20 M
Specifications
Max. Operating pressure 1600 PSI
Water volume 1.6 GPM
Voltage 120 V
Amp draw 13 AMPS
5.962-371.0 (01/08)
Model K 520 M OVERVIEW
Item Description Item Description
1. Power cord with GFCI plug 6. Water inlet
2. Retractable handle 7. Quick-connect adapter
3. Detergent suction tube with filter 8. High pressure hose
4. High pressure outlet 9. Trigger gun safety lock
(not pictured) 10. Trigger gun
5. On/Off switch 11. Vario Spray wand
2
IMPORTANT PRECAUTIONS Read First!
IMPORTANT SAFETY INSTRUCTIONS The Gun Safety Lock prevents the trigger
WARNING When using this product basic from accidentally being engaged. This safety
feature does not lock trigger in the on
precautions should always be followed,
position.
including the following:
Read all the instructions before using the WARNING Risk of Electrocution
product. Inspect cord before using Do not use if cord
To reduce the risk of injury, close supervisi- is damaged.
on is necessary when a product is used near Keep all connections dry and off the ground.
children.
Do not touch plug with wet hands.
Know how to stop the pressure washer and
bleed pressures quickly. Be thoroughly Do not use extension cord with this product.
familiar with the controls. Connect to individual branch circuit only.
Stay alert watch what you are doing.
Do not operate the product when fatigued GROUND FAULT CIRCUIT
or under the influence of alcohol or drugs. INTERRUPTER PROTECTION
Keep operating area clear of all persons. This pressure washer is provided with a
ground-fault circuit-interrupter (GFCI) built into
Do not overreach or stand on unstable the plug of the power-supply cord. This device
support. Keep good footing and balance at provides additional protection from the risk of
all times. electric shock. Should replacement of the plug
Follow the maintenance instructions speci- or cord become necessary, use only identical
fied in the manual. replacement parts that include GFCI protection.
3
This Pressure Washer Is Provided With A
Ground Fault Circuit Interrupter Built Into The
GROUNDING INSTRUCTIONS
Power Cord Plug. If Replacement Of The This product must be grounded. If it should
Plug Or Cord Is Needed, Use Only Identical malfunction or breakdown, grounding provides
Replacement Parts. a path of least resistance for electric current to
reduce the risk of electric shock. This product
WARNING Risk of Injection or Injury
is equipped with a cord having an equipment-
Do Not Direct Discharge Stream At Persons.
grounding conductor and a grounding plug. The
High pressure jets can be dangerous if plug must be plugged into an appropriate outlet
subject to misuse. The jet must not be that is properly installed and grounded in
directed at persons, animals, electrical accordance with all local codes and
devices, or the machine itself. ordinances.
ASSEMBLY INSTRUCTIONS
Step 1 Step 2
Connect the high pressure hose to the units high Insert the vario spray wand into the trigger
pressure outlet. gun. Press in against the spring tension and
twist into the locked position.
Step 3 Step 4
Connect garden hose to units water inlet using Connect garden hose to the cold
the quick connect adapter. water source and turn water on
completely.
Step 5 Step 6
Plug the power cord into the power outlet. Unlock Turn on the pressure washer (I/ON).
the lock of the trigger gun. Trigger the gun to The motor starts only if the trigger of
eliminate trapped air, wait for a steady flow of the gun is pulled and shuts off when
water to emerge from the spray nozzle. the trigger is released.
GFCI INSTRUCTIONS
Note:
The actual
appearance of
the GFCI may
be different
from this
illustration.
Step 1 Step 2
Plug the Ground Fault Circuit Interrupter Press TEST, then press RESET to assure
(GFCI) into a working outlet proper connection to power.
Mix.
Max.
WORKING WITH DETERGENTS
Detergents can only be applied at low pressure (Mix).
Step 1 Step 3
Install the Vario spray wand. Set the Vario Turn on the pressure washer.
spray wand to the low pressure setting (mix) Pull trigger to operate unit: Liquid detergent
by turning the wand collar. The wand must is drawn into the unit and mixed with water.
be set in the low pressure (Mix) position to Apply detergent to work area. Do not allow
apply detergents. detergent to dry on surface.
Caution
Never use:
Bleach, Chlorine products and other
corrosive chemicals
Liquids containing solvents
(i.e., paint thinners, gasoline, oils)
Tri-sodium phosphate products
Ammonia products
Acid-based products
These chemicals will harm the unit and
will damage the surface being cleaned.
SHUTTING DOWN & CLEAN-UP
Step 5 Step 6
Disconnect the garden hose Disconnect the high pressure hose from the high pressure
from the water inlet on the unit. outlet and engage the gun safety lock.
MAINTENANCE INSTRUCTIONS
Cleaning the Cleaning the
water inlet filter detergent filter
Pull out the water Pull out the detergent
inlet filter with flat- suction tube and
nose pliers and rinse filter in warm
rinse filter in warm water.
water.
WINTERIZING AND LONG-TERM STORAGE
1. Disconnect all water connections. 4. Store the machine and accessories in
2. Turn on the machine for a few seconds, a room which does not reach freezing
until the water which had remained in temperatures.
the pump exits. Turn off immediately. Caution: Failure to follow the above
3. Do not allow high pressure hose to directions will result in damage to the pump
become kinked. assembly and accessories.
CLEANING TIPS
Deck Cleaning Cement Patios,
(with or without detergent) Brick and Stone
Pre-rinse deck and surrounding area with fresh (with or without detergent)
water. If using Krcher Deck Wash, place Pre-rinse cleaning surface with fresh water. If
detergent suction tube directly into cleaning using Karcher All Purpose Cleaner, place
solution and apply to surface at low pressure. detergent suction tube directly into cleaning
For best results, limit your work area to smaller solution and apply to surface at low pressure.
sections of approximately 25 square feet. Allow For best results, limit your work area to smaller
Krcher Deck Wash to remain on surface 1-3 sections of approximately 25 square feet. Allow
minutes. Do not allow detergent to dry on Krcher All Purpose Cleaner to remain on
surface. Rinse at high pressure in a long surface 1-3 minutes. Do not allow detergent to
sweeping motion keeping the spray nozzle dry on surface. Rinse at high pressure in a
approximately 3-6 inches from the cleaning sweeping motion keeping the spray nozzle
surface. Always clean from top to bottom and approximately 3-6 inches from the cleaning 9
from left to right. When moving on to a new surface. Always clean from top to bottom and
section of the cleaning surface, be sure to from left to right. For removing extremely
overlap the previous section to eliminate stop stubborn stains, use Krcher Rotating Nozzle
marks and ensure a more even cleaning result. Spray Wand.
Caution: Do not use rotating nozzle spray wand
on wood surface as it may cause damage.
Cars, Boats & Motorcycles
(with or without detergent)
House Siding Pre-rinse vehicle with fresh water. If using
(with or without detergent) Karcher Vehicle Wash, place detergent suction
Pre-rinse cleaning surface with fresh water. If tube directly into cleaning solution and apply
using Krcher House Wash, place detergent to surface at low pressure. For best results,
suction tube directly into cleaning solution and clean one side of vehicle at a time and always
apply to surface at low pressure (for best apply detergent from bottom to top, do not
results, limit your work area to sections of allow detergent to dry on surface. If needed,
approximately 6 feet and always apply use special Wash Brush Attachment to remove
detergent from bottom to top). Allow Karcher stubborn dirt. Rinse at high pressure in a
House Wash to remain on surface 1-3 minutes. sweeping motion keeping the spray nozzle
Do not allow detergent to dry on surface, if approximately 6-8 inches from the cleaning
surface appears to be drying, simply wet down surface (distance should increase when rinsing
surface with fresh water. If needed, use special pin-striping or other sensitive surfaces). Always
Wash Brush Attachment to remove stubborn clean from top to bottom and from left to right.
dirt. Rinse at high pressure from top to bottom For best results, wipe surface dry with a
in an even sweeping motion keeping the spray chamois or soft dry cloth.
nozzle approximately 6 inches from the Caution: Do not use rotating nozzle spray
cleaning surface. wand on vehicles as it may cause damage.
Caution: Do not use rotating nozzle spray
wand on siding as it may cause damage.
CLEANING TIPS continued
Barbecue Grills, Outdoor Patio & Lawn Furniture
Power Equipment & (with or without detergent)
Gardening Tools Pre-rinse furniture and surrounding area
(with or without detergent) with fresh water. If using Krcher All
Pre-rinse cleaning surface with fresh water. Purpose Cleaner, place detergent suction
If using Krcher All Purpose Cleaner or tube directly into cleaning solution and
Degreaser, place detergent suction tube apply to surface at low pressure. Allow
directly into cleaning solution and apply Krcher All Purpose Cleaner to remain on
detergent at low pressure. Allow Krcher surface 1-3 minutes. Do not allow detergent
detergent to remain on surface 1-3 minutes. to dry on surface. If needed use special
Do not allow detergent to dry on surface. Wash Brush Attachment to remove
Rinse at high pressure keeping the spray stubborn dirt. Rinse at high pressure in a
nozzle approximately 3-6 inches from the sweeping motion keeping the spray nozzle
cleaning surface. For removing extremely approximately 3-6 inches from the cleaning
stubborn dirt, it may be necessary to move surface. For best results, clean from top to
the spray nozzle even closer to the surface bottom and from left to right.
for greater dirt cutting action. To remove Caution: Do not use rotating nozzle spray
caked on mud from garbage cans, lawn wand on patio or lawn furniture as it may
mower blades, wheel barrels or other cause damage.
non-sensitive metal surfaces, you may want
to use the Karcher Rotating Nozzle Spray Recommendations
Wand. Before cleaning any surface an
Caution: Do not use rotating nozzle spray inconspicuous area should be cleaned to
wand on cloth, plastic or other sensitive test spray patter n and distance for
surfaces as it may cause damage. maximum cleaning results.
10 If painted surfaces are pealing or chipping,
use extreme caution as pressure washer
may remove the loose paint from the
surface.
OPTIONAL CLEANING
Optional cleaning accessories are available to further enhance your cleaning capabilities: See
accessories order form for product descriptions and ordering instructions.
Rotating Wash Brush Telescopic Spray Wand
Wash Brush Pipe Drain Cleaner
Extension Wand Sandblasting Attachment
Rotating Nozzle Spray Wand Detergent Foamer Attachment
Flexible Spray Wand Extension Hose 25
TROUBLESHOOTING
Disconnect the machine from the power source before making any repair.
Motor will not start On/Off switch is in the OFF (O) Turn switch to the ON (I)
position. position
Unit does not reach high Diameter of garden hose is too Replace with a 3/4 inch garden
pressure. small. hose.
Not enough inlet water supply. Open water source full force.
11
Water inlet filter is clogged. Remove filter and rinse out in
warm water.
Output pressure varies Not enough inlet water supply. Turn water on full force. Check
high and low. garden hose for kinks, leaks or
blockage.
Spray wand leaks. Spray wand not properly attached. Insert the spray wand into the
gun. Carefully press in against the
spring tension and twist into the
12
locked position.
Pump is noisy. Pump is sucking air. Check that hoses and fittings are
air tight. Turn off machine and
purge pump by squeezing trigger
gun until a steady flow of water
emerges through the nozzle.
Water leaks from pump (up Loose fittings. Check that all fittings are tight.
to 10 drops per minute is
permissible). Water seals are damaged or worn. Call service center.
Oil Drip. Oil seals are damaged or worn. Call service center.
1-800-537-4129
Especificaciones
Max. Presin de operacin 1600 PSI
Volumen de agua 1.6 GPM
Tensin 120 V
Amperaje de consumo 13 AMPS
5.962-371.0 (01/08)
MODELO K 520 M GENERALIDADES
Artculo Description Artculo Description
2
PRECAUCIONES IMPORTANTES - Lea Primero!
Precauciones de Seguridad La pistola rebota hacia atrs - sujetar con las
dos manos.
ADVERTENCIA - Al utilizar este producto, tome
siempre las precauciones bsicas, incluidas El seguro del gatillo de la pistola evita que el
las siguientes: gatillo salte de forma involuntaria. El
dispositivo de seguridad NO bloquea el gatillo
Lea todas las instrucciones antes de usar el
en la posicin ON (encendido).
producto.
ADVERTENCIA Riesgo de electrocucin
Para reducir el riesgo de lesiones, es preciso
vigilar atentamente si se usa el producto Examine el cable elctrico antes del uso
cerca de nios. No utilice cable daados.
Es necesario saber cmo parar rpidamente Mantenga todas las conexiones secas y
el producto y parar hemorragias. Estar alejadas del suelo.
familiarizado con los mandos. No toque el enchufe con las manos mojadas.
Estar atento, prestar atencin a lo que se est No se debe usar el cable de extensin para
haciendo. esta mquina.
No ponga en funcionamiento el producto si Conctese solo a un circuito elctrico indivi-
est cansado o est bajo la influencia de dual.
alcohol o drogas.
Mantenga la zona de trabajo libre de Proteccin mediante interruptor de
personas. circuito de avera por puesta a tierra
No sobrecargar o colocar sobre un soporte Este producto se suministra con un interruptor
inestable. Mantener el equilibrio en todo de circuito de avera por puesta a tierra
momento. montado en el enchufe del cable de potencia.
Este aparato proporciona una proteccin
Seguir las instrucciones de mantenimiento
adicional contra el riesgo de electrochoque. Si 3
especificadas en el manual.
es necesario reemplazar el enchufe o el cable,
Este producto se suministra con un utilice piezas idnticas.
interruptor de circuito de avera por puesta a
tierra, que est montado en el enchufe del
cable de potencia. Si es necesario reemplazar
Instrucciones de puesta a tierra
Este producto se tiene que poner a tierra. Si
el enchufe o el cable, utilice slo piezas de
funcionase mal o si se rompiese, la puesta a
repuesto idnticas.
tierra proporcionara una circuito menos resis-
ADVERTENCIA - Riesgo de inyeccin o lesiones tente a la energa elctrica para reducir el riesgo
- no dirigir el chorro directamente sobre de electrochoque. Este producto est equipado
personas. con un cable que tiene un conductor a tierra y
Los aparatos a alta presin pueden resultar un enchufe a tierra para el equipo. El enchufe
peligrosos si se usan de forma incorrecta. No se tiene que enchufar a un tomacorriente
se debe dirigir el aparato a personas, animales, adecuado, que est correctamente instalado y
dispositivos elctricos o la equipo mismo. puesto a tierra conforme a todas las normas y
Utilizar gafas de seguridad. reglamentos locales.
INSTRUCCIONES DE ENSAMBLAJE
Paso 1 Paso 2
Conecte la manguera de alta presin a la salida Inserte la lanza vario en el can de la
de alta presin de la mquina. pistola. Oprima haciendo presin en
contra de la tensin del resorte y de le
vuelta a la lanza para asegurarlo en
posicin.
Paso 3 Paso 4
Conecte la manguera de jardn a la entrada de Conecte la manguera de jardn a la
agua de la mquina. toma de agua fra y abra
completamente la llave de agua.
Paso 5 Paso 6
Conecte el cable elctrico a la toma de corriente. Encienda la mquina de alta presin (I/ON).
Oprima el gatillo de la pistola para eliminar el aire El motor arranca solamente si el gatillo
atrapado, espere a que salga un flujo continuo de de la pistola se encuentra jalado y se
agua por la boquilla. apaga cuando se suelta el gatillo.
INSTRUCCIONES DEL DISYUNTOR DE CORTOCIRCUITO A TIERRA (GFCI)
Nota:
La apariencia real
del Disyuntor de
Cortocircuito a
Tierra (GFCI)
puede ser diferente
a esta ilustracin.
Paso 1 Paso 2
Conecte el Disyuntor de Oprima "TEST" (Prueba), despus oprima
Cortocircuito a Tierra (GFCI) a una "RESET" (Restablecer) para asegurar la
toma de corriente. conexin adecuada a la toma de
corriente.
Mix.
Max.
TRABAJANDO CON DETERGENTES
Los detergentes solamente pueden aplicarse en presin baja (Mix).
Paso 1 Paso 3
Para aplicar detergentes, instale la lanza Oprima el gatillo de la pistola para hacer
Vario. Coloque la lanza Vario en la puesta funcionar la maquina: el detergente lquido
de baja presin (Mix) dndole vuelta al es aspirado hacia la maquina y se mezcla
collar de la lanza. La lanza debe estar con el agua. Aplique el detergente al rea
colocada en la posicin de presin baja de trabajo. No permita que el detergente se
(Mix) para aplicar detergentes. seque sobre la superficie.
8
Paso 5 Paso 6
Desconecte la manguera de Desconecte la manguera de alta presin de la salida de alta
jardn de la entrada de agua de presin y asegure la aldaba de seguridad de la pistola.
la mquina.
SUGERENCIAS DE LIMPIEZA
Limpieza de Cubiertas Patios de Cemento, Ladrillo y
(con o sin detergente) Piedra (con o sin detergente)
Pre-enjuague la cubierta y el rea circun-dante Pre-enjuague la superficie a limpiar con agua
con agua limpia. Si utiliza el Jabn para limpia. Si utiliza el Limpiador para todo uso Kr-
Cubiertas Krcher, coloque el tubo de succin cher, coloque el tubo de succin de detergente
de detergente directamente en la solucin directamente en la solucin limpiadora y
limpiadora y aplquela a la superficie a baja aplquela a la superficie a baja presin. Para
presin. Para obtener mejores resultados, limite obtener mejores resultados, limite su rea de
su rea de trabajo a sec-ciones pequeas de trabajo a secciones pequeas de aprox. 25 pies
aproximadamente 25 pies cuadrados. Permita cuadrados. Permita que el Limpiador para todo
que el Jabn para Cubiertas Krcher uso Krcher permanezca sobre la superficie
permanezca sobre la superficie durante 1 a 3 durante 1 a 3 minutos. No permita que el
minutos. No permita que el detergente se seque detergente se seque sobre la superficie.
sobre la superficie. Enjuague a alta presin con Enjuague a alta presin con un movimiento de
un movimiento amplio de barrido manteniendo barrido manteniendo la boquilla a una distancia
la boquilla a una distancia aproximada de 3 a 6 aproximada de 3 a 6 pulgadas de la superficie
pulgadas de la superficie a limpiar. Limpie a limpiar. Limpie siempre de arriba hacia abajo 9
siempre de arriba hacia abajo y de izquierda a y de izquierda a derecha. Para eliminar
derecha. Cuando prosiga hacia una seccin manchas muy persistentes, utilice la lanza de
nueva de la superficie a limpiar, asegrese de boquilla rotante Krcher.
encimar sobre la seccin previa para eliminar
marcas y asegurar una limpieza ms uniforme. Automviles, Botes y Motocicletas
Precaucin: No utilice la lanza de boquilla rot- (con o sin detergente)
ante sobre superficies de madera ya que puede Pre-enjuague el vehculo con agua limpia. Si
ocasionar daos. utiliza el Jabn para Vehculos Krcher, coloque
el tubo de succin de detergente directamente
Muebles de Patio y Jardn en la solucin limpiadora y aplquela a la
(con o sin detergente) superficie a baja presin. Para obtener mejores
Pre-enjuague los muebles y el rea circundante resultados, limpie todo un lado del vehculo a
con agua limpia. Si utiliza el Limpiador para todo la vez y aplique siempre el detergente de abajo
uso Krcher, coloque el tubo de succin de hacia arriba, no permita que el detergente se
detergente directamente en la solucin seque sobre la superficie. Si es necesario,
limpiadora y aplquela a la superficie a baja utilice el accesorio de Cepillo de lavar para
presin. Permita que el Limpiador para todo uso eliminar la suciedad persistente. Enjuague a
Krcher permanezca sobre la superficie durante alta presin con un movimiento de barrido
1 a 3 minutos. No permita que el detergente se manteniendo la boquilla a una distancia
seque sobre la superficie. Si es necesario, utilice aproximada de 6 a 8 pulgadas de la superficie
el Aditamento especial de cepillo de lavar para a limpiar (esta distancia debe aumentar cuando
eliminar suciedad persistente. Enjuague a alta enjuague superficies que tienen rayas u otras
presin con un movimiento de barrido superficies sensibles). Limpie siempre de arriba
manteniendo la boquilla a una distancia hacia abajo y de izquierda a derecha. Para
aproximada de 3 a 6 pulgadas de la superficie a obtener mejores resultados, seque la superficie
limpiar. Para obtener mejores resultados, limpie con una piel o pao suave y seco.
de arriba hacia abajo y de izquierda a derecha. Precaucin: No utilice la lanza de boquilla rot-
Precaucin: No utilice la lanza de boquilla rot- ante sobre vehculos ya que puede ocasionar
ante sobre muebles de patio o jardn ya que daos.
puede ocasionar daos.
SUGERENCIAS DE LIMPIEZA - continuacin
Parrillas para Carne, Equipo Flancos de la Casa
Motorizado para Exteriores y (con o sin detergente)
Herramientas de Jardinera Pre-enjuague la superficie a limpiar con agua
(con o sin detergente) limpia. Si utiliza el Jabn para Casas Krcher,
Pre-enjuague la superficie a limpiar con agua coloque el tubo de succin de detergente
limpia. Si utiliza el Limpiador para todo uso directamente en la solucin limpiadora y
Krcher o el Desengrasante, coloque el tubo aplquela a la superficie a baja presin (para
de succin de detergente directamente en la obtener mejores resultados, limite su rea de
solucin limpiadora y aplique el detergente a trabajo a secciones de aproximadamente 6
baja presin. Permita que el detergente pies y aplique siempre el detergente de abajo
Krcher permanezca sobre la superficie hacia arriba). Permita que el Jabn para
durante 1 a 3 minutos. No permita que el Casas Krcher permanezca sobre la
detergente se seque sobre la superficie. superficie durante 1 a 3 minutos. No permita
Enjuague a alta presin manteniendo la que el detergente se seque sobre la
boquilla a una distancia aproximada de 3 a 6 superficie, si parece que la superficie se est
pulgadas de la superficie a limpiar. Para secando, simplemente mjela con agua
eliminar suciedad muy persistente, puede ser limpia. Si es necesario, utilice el aditamento
necesario acercar an ms la boquilla a la especial de cepillo de lavar para eliminar la
superficie para lograr una accin cortante de suciedad persistente. Enjuague a alta presin
grasa ms eficiente. Para quitar muchas desde arriba hacia abajo con un movimiento
capas de lodo de latas de basura, hojas de de barrido uniforme, manteniendo la boquilla
cortadoras de pasto, barriles u otras a una distancia aproximada de 6 pulgadas de
superficies metlicas no sensibles, puede la superficie a limpiar.
utilizar la lanza de boquilla rotante Krcher. Precaucin: No utilice la lanza de boquilla
Precaucin: No utilice la lanza de boquilla rotante sobre los flancos ya que puede
rotante sobre superficies de tela, plstico u ocasionar daos.
10
otras superficies sensibles, ya que puede
ocasionar daos. Recomendaciones
Antes de limpiar cualquier superficie, debe
limpiar una superficie oculta para probar el
patrn de rociado y distancia para obtener
resultados mximos de limpieza.
Si la pintura de las superficies se encuentra
levantada o quebrada, extreme
precauciones, ya que la mquina lavadora
a presin puede desprender la pintura
suelta de la superficie.
El motor no arranca El interruptor On/Off est en posicin Coloque el interruptor en posicin ON (I)
OFF (O) (apagado). (encendido).
La presin de salida No hay suficiente entrada de agua. Abra la llave de agua al mximo. Revise que
vara de alta a baja. la manguera de jardn no est torcida, tenga
fugas o est obstruida.
El filtro de entrada de agua est tapado. Quite el filtro y enjuguelo en agua tibia.
La boquilla de descarga est obstruida. Sople o quite el ensombros con una aguja
fina.
El filtro del tubo de succin de Haga correr agua tibia a travs del filtro
detergente est tapado. para eliminar el residuo.
La conexin de Las piezas de conexin estn flojas. Ajuste las piezas de conexin.
la manguera
de jardn gotea. Faltan las rondanas o estn gastadas. Inserte rondanas nuevas.
La bomba hace La bomba est aspirando aire. Revise que las mangueras y piezas de con-
mucho ruido. exin no permitan el paso de aire. Apague
la mquina y purgue la bomba oprimiendo
el gatillo de la pistola hasta que salga un
flujo constante de agua por la boquilla.
Gotea agua de la bomba Las piezas de conexin estn sueltas. Revise que todas las piezas de conexin
(se permiten hasta 3 estn apretadas.
gotas
por minuto). Los sellos de agua estn daados o Llame al centro de servicio.
gastados.
Goteo de aceite. Los sellos de aceite estn daados o Llame al centro de servicio.
gastados.