Escolar Documentos
Profissional Documentos
Cultura Documentos
Cedar Ridge
hearth
OWNERS OPERATION AND
INSTALLATION MANUAL
MODELS
CRHEB24RT AND CRHEB30RT
PFS
US
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
Do not store or use gasoline or other flammable va-
pors and liquids in the v icinity of this or any other
appliance.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not use any
phone in your building.
Immediately call your gas supplier from a neighbors
phone. Follow the gas suppliers instructions.
If you cannot reach your gas supplier, call the fire
department.
Installation and service must be performed by a quali-
fied installer, service agency or the gas supplier.
WARNING: This appliance is equipped for Natural and
Propane gas. Field conversion is not permitted other than
between natural or propane gases.
Questions, problems, missing parts? Before returning to your retailer, call
our customer service department at 1-866-573-0674, 8:00 am - 4:30 pm CST,
Monday through Friday or email customerservice@usaprocom.com
TABLE OF CONTENTS
Safety......................................................... 3 Operation.................................................. 21
Specifications............................................. 5 Inspecting Burners................................... 26
Qualified Installing Agency......................... 5 Care And Maintenance............................. 27
Product Features........................................ 5 Troubleshooting........................................ 29
Product Identification.................................. 5 Parts......................................................... 32
Local Codes............................................... 6 Replacement Parts................................... 34
Unpacking.................................................. 6 Accessories.............................................. 34
Water Vapor: A By-Product Of Service Hints............................................ 35
Unvented Room Heaters...................... 6 Technical Service..................................... 35
Air For Combustion and Ventilation............ 7 Warranty................................................... 36
Installation................................................ 10
2 www.usaprocom.com 200015-01B
SAFETY
CARBON MONOXIDE POISONING: Early
WARNING: This appliance is signs of carbon monoxide poisoning resemble
for installation only in a solid- the flu, with headaches, dizziness or nausea.
fuel burning masonry or UL127 If you have these signs, the heater may not
factory-built fireplace or in a be working properly. Get fresh air at once!
Have heater serviced. Some people are
listed ventless firebox enclo- more affected by carbon monoxide than oth-
sure. Exception: Do not install ers. These include pregnant women, people
this appliance in a factory-built with heart or lung disease or anemia, those
fireplace that includes instruc- under the influence of alcohol and those at
tions stating it has not been high altitudes.
tested or should not be used NATURAL AND PROPANE/LP GAS: Natural
with unvented gas logs. and Propane/LP gas are odorless. An odor-
making agent is added to the gas. The odor
helps you detect a gas leak. However, the
IMPORTANT: Read this owners odor added to the gas can fade. Gas may be
manual carefully and completely present even though no odor exists.
before trying to assemble, op-
erate, or service this heater. WARNING: Any change to
Improper use of this heater can this heater or its controls can
cause serious injury or death be dangerous.
from burns, fire, explosion,
electrical shock and carbon WARNING: Do not allow fans
monoxide poisoning. Failure to blow directly into fireplace.
to follow these instructions will Avoid any drafts that alter burner
void the warranty. flame patterns.
200015-01B www.usaprocom.com 3
SAFETY
8. Do not use heater if any part has been
WARNING: The log set be- under water. Immediately call a qualified
comes very hot when running. service technician to inspect the room
Keep children and adults away heater and to replace any part of the
from hot surfaces to avoid burns control system and any gas control which
has been under water.
or clothing ignition. Fireplace
9. Turn off heater and let cool before servic-
will remain hot for a time after ing. Only a qualified service person should
shutdown. Allow surfaces to service and repair heater.
cool before touching. 10. Operating heater above elevations of
4,500 feet could cause pilot outage.
WARNING: Carefully super- 11. To prevent performance problems, do
vise young children when they not use propane/LP fuel tank of less than
are in the room with the heater. 100lbs. capacity.
12. Do not use this heater as a wood-burning
WARNING: You must operate heater. Use only the logs provided with the
this log set with screen in place. heater.
13. Solid fuels should not be burned in
1. Do not place Propane/LP supply tank(s) fireplace in which a vent-free log set is
inside any structure. Propane/LP supply installed. Do not use this heater to cook
tank(s) must be placed outdoors. food or burn paper or other objects.
2. This heater shall not be installed in a 14. To prevent sooting, follow the instructions
bedroom or bathroom. in Care and Maintenance (see page 27).
3. This heater needs fresh air ventilation to 15. Do not add extra logs or ornaments such
run properly. This heater has an Oxygen as pine cones, vermiculite, or rock wool.
Depletion Sensing (ODS) safety shutoff Using these added items can cause soot-
system. The ODS shuts down the heater ing. Do not add lava rock around base.
if not enough fresh air is available. See Air Rock and debris could fall into the control
for Combustion and Ventilation, pages 7 area of heater. After servicing, always
through 9. If heater keeps shutting off, see replace screen before operating heater.
Troubleshooting, page 29. 16. This heater is designed to be smokeless. If
4. Keep all air openings in front and bottom logs ever appear to smoke, turn off heater
of heater clear and free of debris. This will and call a qualified service person.
ensure enough air for proper combustion. Note: During initial operation, slight smok-
5. If heater shuts off, do not relight until you ing could occur due to log curing and the
have provided fresh, outside air. If heater heater burning manufacturing residues.
keeps shutting off, have it serviced. 17. If fireplace has glass doors, never operate
6. Do not run heater: this heater with glass doors closed. If you
Where flammable liquids or vapors are operate heater with doors closed, heat will
used or stored. build up inside fireplace and cause glass
Under dusty conditions. to burst. If fireplace opening has vents
7. Before using furniture polish, wax, carpet at the bottom, you must open the vents
cleaner, or similar products, turn heater before operating log set. Always operate
off. If heated, the vapors from these prod- heater with glass doors fully open.
ucts may create a white powder residue 18. Do not use this heater if any log is broken.
within burner box or on adjacent walls or Do not operate heater if a log is chipped
furniture. (dime-size or larger).
4 www.usaprocom.com 200015-01B
SPECIFICATIONS
Models CRHEB24RT and CRHEB30RT
Gas Type Natural Gas Propane Gas
Ignition Electronic Piezo Ignitor Electronic Piezo Ignitor
Input Rating 35,000 Btu/Hr 35,000 Btu/Hr
Manifold Pressure 4" W.C. 9" W.C.
Inlet Gas Pressure* (inches Maximum 10.5" Maximum 14"
of water) (*for purposes of
input adjustment) Minimum 5" Minimum 11"
PRODUCT FEATURES
This log set has been tested and approved to PIEZO IGNITION SYSTEM
ANSI Z21.11.2 standard for Unvented Heat- This heater is equipped with an electronic
ers and can be operated with the flue damper piezo control system. This system requires
closed. State and local codes in some areas one AAA battery (provided).
prohibit the use of vent-free heaters.
2 GAS OPTIONS AVAILABLE
SAFETY PILOT Your heater is equipped to operate on either
This heater has a pilot with an Oxygen Deple- Propane/LP or Natural gas. The heater is
tion Sensing (ODS) safety shutoff system. The shipped from the factory ready for connect-
ODS/pilot shuts off the heater if there is not ing to Propane/LP. The heater can easily be
enough fresh air. changed to Natural gas by having your quali-
fied installer follow the instructions on page
14 and the markings on the heater.
PRODUCT IDENTIFICATION
The hardware packet supplied with this heater
Logs
should contain the following items:
1 - Owners Manual
1 - User Contact Page
1 - Warranty Card
1 - Allen Wrench
2 - Self Tapping Screws, GB/T845-4.8*26Z
1 - Bag of Embers
1 - Bag of Lava Rock
1 - Receiver
Ignitor Button Burner Control Knob 1 - Remote Control
2 - AAA Batteries
Figure 1 - Vent-Free Log Set 4 - AA Batteries
200015-01B www.usaprocom.com 5
LOCAL CODES
Install and use heater with care. Follow all
local codes. In the absence of local codes, State of Massachusetts: The installation
use the latest edition of The National Fuel must be made by a licensed plumber or
Gas Code, ANSI Z223.1/NFPA 54*. gas fitter in the Commonwealth of Mas-
sachusetts.
*Available from:
American National Standards Institute, Inc. Sellers of unvented propane or natural
1430 Broadway gas-fired supplemental room heaters shall
New York, NY 10018 provide to each purchaser a copy of 527
National Fire Protection Association, Inc. CMR 30 upon sale of the unit.
1 Batterymarch Park In the State of Massachusetts the gas
Quincy, MA 02269-9101 cock must be a T-handle type. The State
of Massachusetts requires that a flexible
This heater is designed for vent-free op-
appliance connector cannot exceed three
eration. State and local codes in some areas
feet in length.
prohibit the use of vent-free heaters.
UNPACKING
1. Remove logs and burner base assembly 2. Remove all protective packaging applied
from carton. to logs and heater for shipment.
Note: Do not pick up burner base as- 3. Check all items for any shipping damage.
sembly by burners as this could damage If damaged, promptly inform dealer where
heater. Always handle base assembly by you purchased the heater.
grate.
6 www.usaprocom.com 200015-01B
AIR FOR COMBUSTION AND VENTILATION
heat loss in homes. Home owners weather
WARNING: This heater shall strip and caulk around windows and doors
not be installed in a confined space to keep the cold air out and the warm air in.
or unusually tight construction During heating months, home owners want
unless provisions are provided their homes as airtight as possible.
While it is good to make your home energy
for adequate combustion and
efficient, your home needs to breathe. Fresh
ventilation air. Read the following air must enter your home. All fuel-burning ap-
instructions to insure proper fresh pliances need fresh air for proper combustion
air for this and other fuel-burning and ventilation.
appliances in your home. Exhaust fans, fireplaces, clothes dryers and
fuel burning appliances draw air from the house
Todays homes are built more energy efficient to operate. You must provide adequate fresh
than ever. New materials, increased insulation air for these appliances. This will insure proper
and new construction methods help reduce venting of vented fuel-burning appliances.
200015-01B www.usaprocom.com 7
AIR FOR COMBUSTION AND VENTILATION
DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if You Have a Confined or Unconfined Space
Use this work sheet to determine if you have 4. Compare the maximum Btu/Hr the space
a confined or unconfined space. can support with the actual amount of Btu/
Space: Includes the room in which you will Hr used.
install heater plus any adjoining rooms with ________Btu/Hr (maximum can support)
doorless passageways or ventilation grills ________Btu/Hr (actual amount used)
between the rooms. Example: 51,200 Btu/Hr (maximum the
1. Determine the volume of the space (length space can support)
x width x height). 56,000 Btu/Hr (actual amount
Length x Width x Height =__________cu. of Btu/Hr used)
ft. (volume of space) The space in the above example is a confined
space because the actual Btu/Hr used is more
Example: Space size 20 ft. (6.1 m)
than the maximum Btu/Hr the space can sup-
(length) x 16 ft. (4.88 m) (width) x
port. You must provide additional fresh air.
8 ft. (2.44m) (ceiling height) = 2560 cu.
Your options are as follows:
ft. (72.49 m ) (volume of space)
3
8 www.usaprocom.com 200015-01B
AIR FOR COMBUSTION AND VENTILATION
VENTILATION AIR
Ventilation Air From Inside Building
This fresh air would come from an adjoining 1 and 2, Figure 2). You can also remove door
unconfined space. When ventilating to an into adjoining room (see option 3, Figure 2).
adjoining unconfined space, you must provide Follow the National Fuel Gas Code, ANSI
two permanent openings: one within 12" of the Z223.1/NFPA 54, Air for Combustion and
ceiling and one within 12" of the floor on the Ventilation for required size of ventilation
wall connecting the two spaces (see options grills or ducts.
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation IMPORTANT: Do not provide openings
grills or ducts. You must provide two perma- for inlet or outlet air into attic if attic has a
nent openings: one within 12" of the ceiling thermostat-controlled power vent. Heated air
and one within 12" of the floor. Connect these entering the attic will activate the power vent.
items directly to the outdoors or spaces open Rework worksheet, adding the space of the
to the outdoors. These spaces include attics adjoining unconfined space. The combined
and crawl spaces. Follow the National Fuel spaces must have enough fresh air to supply
Gas Code, ANSI Z223.1/NFPA 54, Air for all appliances in both spaces.
Combustion and Ventilation for required size
of ventilation grills or ducts.
Ventilated
Outlet Attic
Air
Outlet
12" Air
To Attic
Ventilation
Grills Ventilation Grills To
Into Adjoining Into Adjoining Room, Crawl
Or Space
Room, Option 2
Remove
Option 1 Inlet
Door into
Air
Adjoining
Inlet Air Ventilated
Room,
Crawl Space
Option
3
Figure 3 - Ventilation Air from Outdoors
12"
200015-01B www.usaprocom.com 9
INSTALLATION
10 www.usaprocom.com 200015-01B
INSTALLATION
CHECK GAS TYPE Minimum Noncombustible Material
Be sure your gas supply is right for your heat- Clearances
er. Otherwise, call dealer where you bought If Not Using Mantel
the heater for proper type heater. Note: If using a mantel, proceed to If Using
CLEARANCES TO Mantel. If not using a mantel, follow the infor-
COMBUSTIBLES mation below.
You must have noncombustible material(s)
WARNING: Maintain the above the fireplace opening. Noncombustible
materials (such as slate, marble, tile, etc.)
minimum clearances. If possible, must be at least 1/2" thick. With sheet metal,
provide greater clearances from you must have noncombustible material be-
floor, ceiling, and adjoining wall. hind it. Noncombustible material must extend
Measure from outermost point at least 12" up (for all models). See Figure 5
of heater. for minimum clearances.
Requirements for Safe Installation
Minimum Fireplace Clearance To
Combustible Materials (A) 12" or more: Noncombustible
material OK.
Side Wall 16", Ceiling 42", Front 36"
(A) Between 8" and 12":
LOG SIZING REQUIREMENTS Install fireplace hood accessory.
Minimum Firebox Size (A) Less than 8": Noncombustible
24" Log Set: Height 20", Depth 15", material must be extended to at least 8".
Front Width 28", Rear Width 23" See Between 8" and 12", above. If you
cannot extend material, you must operate
30" Log Set: Height 20", Depth 15", heater with flue damper open.
Front Width 34", Rear Width 23"
Minimum Clearances For Side
Combustible Material, Side Wall
and Ceiling
A. Clearance from the side of the fireplace
cabinet to any combustible material and Noncombustible
Material Distance
wall should follow diagram in Figure 4.
B. Clearance from the top of the fireplace
opening to the ceiling must not be less
than 42".
200015-01B www.usaprocom.com 11
INSTALLATION
If Using Mantel at least 8" up. If noncombustible material is
You must have noncombustible material(s) less than 12", you must install the fireplace
above the fireplace opening. Noncombustible hood accessory. Even if noncombustible
materials (such as slate, marble, tile, etc.) material is more than 12", you may need the
must be at least 1/2" thick. With sheet metal, hood accessory to deflect heat away from
you must have noncombustible material be- your mantel shelf. See Figures 5, 6 and 7, for
hind it. Noncombustible material must extend minimum clearances.
MANTEL CLEARANCES
In addition to meeting noncombustible mate- Mantel Shelf
rial clearances, you must also meet required 10"
8" Underside of
clearances between fireplace opening and 6" Mantel Shelf
mantel shelf. If you do not meet the clearances 2 1/2"
12 www.usaprocom.com 200015-01B
INSTALLATION
FLOOR CLEARANCES
A. If installing appliance on the floor level, B. If combustible materials are less than 14"
you must maintain the minimum distance to the fireplace, you must install appliance
of 14" to combustibles (see Figure 8). at least 5" above the combustible flooring
(see Figure 9).
Combustible
14" Material Hearth
Combustible
Min. Material
5"
Min.
Noncombustible Material
GAS SELECTION
Change of the selector setting to other than
This appliance is factory the fuel type specified at the time of installa-
preset for propane/LP gas. tion could damage this appliance and render
No changes are required for it inoperable.
connecting to propane/LP. Only The installer shall replace the access cover
a qualified installer or service before completing the installation and operat-
technician can perform gas selec- ing this appliance.
tion and connecting to gas supply. For changing from propane to
natural gas supply:
1. Remove 2 screws from cover plate located
CAUTION: Two gas line in-
on left side of heater (see Figure 10).
stallations at the same time are
2. For NATURAL GAS, press in knob using a
prohibited. The access plate flat screwdriver with a blade with thickness
to the simple switching means of a quarter and turn knob clockwise
shall not be opened while the until the knob locks into the NG position
heater is in operation. (see Figure 10). Fuel selection device
must be locked in the NG position. Do not
CAUTION: To avoid gas operate heater between locked positions!
leakage at the inlet of regulator, 3. Replace cover over fuel selection device
and reinstall screws.
a qualified installer or service
technician must use supplied Hex Plug Fuel Selector Knob
hex plug with sealant. LP
NG
WARNING: Do not attempt to
access or change the setting of LP
NG
the fuel selection means. Gas
Connection
Access to and adjustment of the fuel selection Fitting
means must only be performed by a qualified Left Side of Heater
service person when connecting this appliance to Figure 10 - Settings for Natural Gas
a specified fuel supply at the time of installation. Selection
200015-01B www.usaprocom.com 13
INSTALLATION
4. Remove hex plug (with wrench provided) 4. Remove hex plug (with wrench provided)
from natural gas inlet of regulator (see from propane/LP gas inlet of regulator
Figure 10, page 13). Install hex plug into (see Figure 11). Install hex plug into NG
LP inlet of regulator. Install gas line into inlet of regulator. Install gas line into LP
NG inlet of regulator. Use thread sealant inlet of regulator. Use thread sealant to
to assure there are no leaks. assure there are no leaks.
For changing from natural gas Gas
supply to propane supply: Connection Fuel Selector Knob
1. Remove 2 screws from cover plate located Fitting LP
on left side of heater (see Figure 11). NG
2. For propane gas, press in knob using a flat
screwdriver with a blade the thickness of
a quarter and turn knob counterclockwise LP
NG
until the knob locks into the LP posi-
tion (see Figure 11). Fuel selection device Hex Plug
must be locked in the LP position. Do not
operate heater between locked positions. Left Side of Heater
3. Replace cover over fuel selection device Figure 11 - Settings for Propane/LP Gas
and reinstall screws. Selection
200015-01B www.usaprocom.com 15
INSTALLATION
Typical Inlet Pipe Diameters Install sediment trap in supply line as shown
Use 3/8" black iron pipe or greater. Installa- in Figure 13. Place sediment trap where it is
tion must include an equipment shutoff valve, within reach for cleaning. Place sediment trap
union, and plugged 1/8" NPT tap. Locate where trapped matter is not likely to freeze.
NPT tap within reach for test gauge hook up. A sediment trap traps moisture and contami-
NPT tap must be upstream from heater (see nants. This keeps them from going into heater
Figure 13). controls. If sediment trap is not installed or is
IMPORTANT: Install an equipment shutoff installed wrong, heater may not run properly.
valve in an accessible location. The equip-
ment shutoff valve is for turning on or shutting WARNING: Test all gas piping
off the gas to the appliance. and connections for leaks after
For propane/LP installations, apply pipe installing or servicing. Correct
joint sealant lightly to male threads. This will all leaks at once (see page 17).
prevent excess sealant from going into pipe.
Excess sealant in pipe could result in clogged
heater valves.
The installer must supply an external regula-
tor. The external regulator will reduce incom-
ing gas pressure. You must reduce incoming
gas pressure to between 11" WC and 14" WC.
If you do not reduce incoming gas pressure,
heater regulator damage could occur. Install
external regulator with the vent pointing down
as shown in Figure 14. Pointing the vent down
protects it from freezing rain or sleet.
3/8" NPT
Ground Pipe Nipple
Joint Union
External
Equipment
Regulator with
Tee Joint Shutoff Valve Propane/LP Vent Pointing
Supply Tank Down
Reducer Natural Gas
Test Gauge Bushing to From Gas Meter
Connection* 1/8" NPT (5" W.C.** to
10.5" W.C.
1/8" NPT Pressure)
Plug Tap Propane/LP
From External
Tee Joint Regulator
(11" W.C.**
Sediment Pipe Nipple to 14" W.C.
Trap 3" Minimum Pressure)
Gap
16 www.usaprocom.com 200015-01B
INSTALLATION
CHECKING GAS CONNECTIONS
Open
Equipment
Shutoff Valve
Gas Meter
Closed
Figure 15 - Equipment Shutoff Valve
200015-01B www.usaprocom.com 17
INSTALLATION
PRESSURE TESTING HEATER GAS CONNECTIONS
1. Open equipment shutoff valve (see Figure 17, page 17). Apply a noncorrosive leak
15, page 17). detection fluid to all joints. Bubbles form-
2. Open main gas valve located on or near ing show a leak.
gas meter for natural gas or open pro- 5. Correct all leaks at once.
pane/LP supply tank valve. 6. Light heater (see Lighting Instructions on
3. Make sure control knob of heater is in the page 21). Check all other internal joints
OFF position. for leaks.
4. Check all joints from equipment shutoff 7. Turn off heater (see To Turn Off Gas Ap-
valve to control valve (see Figure 16 or pliance, page 22).
18 www.usaprocom.com 200015-01B
INSTALLATION
PLACING EMBER MATERIAL
Separate the ember material into light pieces
smaller than the size of a dime. Place the WARNING: Use only ember
pieces around the round gas ports starting in material provided with log set.
the front of the burner and working your way Do not add additional ember
toward the back of the burner. Do not place material.
ember material on the slotted burner ports or
the carry over ports leading to the left and right Place ember material on front
rear burner slots. burner port only. DO NOT PLACE
EMBER MATERIAL ON PORTING
BEYOND THE GRATE, OVER THE
MIDDLE OR BACK BURNERS.
Log #3
Slot for Log #4
Log #4
LIGHTING INSTRUCTIONS
8. Push in control knob slightly and turn
WARNING: You must oper- counterclockwise to the PILOT
ate this heater with the screen position. Press in control knob for five (5)
in place. Make sure screen is seconds.
installed before running heater. Note: The first time that the heater is oper-
ated after connecting the gas supply, the
NOTICE: During initial operation of control knob should be pressed for about
new heater, burning logs will give thirty (30) seconds. This will allow air to
bleed from the gas system. If pilot does not
off a paper-burning smell. Orange stay lit, refer to Troubleshooting, pages 29
flame will also be present. Open though 31. Also contact a qualified service
damper or window to vent smell. technician or gas supplier for repairs. Until
This will only last a few hours. repairs are made, light pilot with match.
If control knob does not pop up when
1. STOP! Read the safety information above. released, contact a qualified service
2. Unscrew ignitor cap and install a AAA bat- technician or gas supplier for repairs.
tery with the + pointing out. Replace cap.
3. Install two AAA size batteries in the remote
control (see page 23).
4. Be sure the slide switch on the front of the
receiver box is in the REMOTE position.
5. Make sure equipment shutoff valve is fully
open.
6. Push in control knob slightly and turn
clockwise to the OFF position.
7. Wait five (5) minutes to clear out any gas.
Then smell for gas around heater and near
the floor. If you smell gas, STOP! Follow Ignitor Button Control Knob
"B" in the safety information above. If you Figure 26 - Ignitor Button and Control
do not smell gas, go to the next step. Knob Locations
200015-01B www.usaprocom.com 21
OPERATION
9. With control knob pressed in, push 12. Press the LEARN BUTTON on the front of
down and release ignitor button. This the remote receiver box until you hear a
will light pilot. The pilot is attached to beep (see Programming the Remote and
the rear of the burner. If needed, keep Receiver, page 23).
pressing ignitor button until pilot lights. 13. Press the ON button on the remote control
Note: If pilot does not stay lit, refer to transmitter to light the burner. (This will
Troubleshooting, pages 29 though 31. also learn, or program, the transmitter
Also contact a qualified service technician and the receiver).
or gas supplier for repairs. Until repairs Note: If the transmitter is lost or damaged,
are made, light pilot with match. To light the slide switch on the receiver can be
pilot with match, see Manual Lighting used to operate the heater.
Procedure.
10. Keep control knob pressed in for 30 sec- CAUTION: Do not try to ad-
onds after lighting pilot. After 30 seconds, just heating levels by using the
release control knob.
equipment shutoff valve.
Note: If pilot goes out, repeat steps 7
through 10. This heater has a safety in-
terlock system. Wait one (1) minute before WARNING: If input gas
lighting pilot again. type is NG, make sure NG pilot
11. Turn control knob counterclockwise burner ignites. If input gas type
to the ON position. The main burner is LP, make sure LP pilot burner
should light. ignites.
Note: Please wait one minute after shut-
ting off heater to allow the control valve
to reset before starting again.
22 www.usaprocom.com 200015-01B
OPERATION
REMOTE CONTROL SYSTEM
Install Batteries 2. Place the slide switch on the receiver in
Batteries are required in both the Remote the remote position (see Figure 28).
Control (Transmitter) (2 AAA size) and Re- 3. Use a pen or small screwdriver to gently
ceiver (4 AA size) (see Figure 27). press and release the recessed LEARN
Note: Be sure batteries are placed correctly. button on the face of the receiver. You will
Reversing the batteries can cause damage to hear a beep.
the receiver and remote. Replace all batteries 4. Press the ON button on the remote (see
on a yearly basis or sooner. Figure 28). You will hear a series of beeps.
Your appliance should come on.
Matching Security Codes
AA
F
AA
Battery Instructions
Be sure to observe proper polarity (+/-)
CAUTION: Do not mix old and when installing or replacing the batteries.
new batteries. Do not mix alka- Damage due to improper battery installation
line, standard (carbon - zinc), or may void the warranty on the product.
rechargeable (nickel - cadmium) For remote control systems, maximize bat-
batteries. Do not dispose of tery life by turning off the receiver when it
is not in use.
batteries in fire, batteries may
For long periods of non-operation, remove
explode or leak. batteries from all components for safety.
Batteries are included. Component Type of Battery Qty.
Remove batteries when depleted. Ignitor AAA 1
Install/replace the batteries according to the Remote Control AAA 2 or 3*
type and quantity stated in table to the right.
Remote Receiver AA 4
Do not mix old and new batteries. New bat-
teries should be the same brand for best *Note: Quantity depends on model of remote
results. Control.
200015-01B www.usaprocom.com 23
OPERATION
REMOTE CONTROL OPERATION
This appliance must not be used with glass SettingF/C Scale
doors in the closed position. This can lead The factory setting for temperature is F. To
to pilot outages and severe sooting outside change this setting toC, press the ON key
the fireplace. and the OFF key on the remote control at the
The transmitter operates on 2 AAA batteries. same time (see Figure 29). This will change
fromF to C. Follow this same procedure to
Key Settings
change fromC back toF.
ON - Operates unit to on position, manually
operated solenoid ON. Manual Function
OFF - Operates unit to off position, manually To operate the system in the manual MODE
operated solenoid OFF. do the following.
MODE - Changes unit from manual mode to ON OPERATION
thermo mode. Press the ON key and the appliance flame will
SET - Sets temperature in thermo mode. come on. During this time the LCD screen will
show ON (see Figure 31).
After 3 seconds the LCD screen will default to
display room temperature and the word TEMP
TEMP
will show (see Figure 31). The flame icon will
appear on LCD screen in manual on mode.
TEMP
Figure 31 - Manual Mode in ON Operation
2
1
3
4 ROOM SET TEMP 5
6
Figure 30 - Remote Control Display
24 www.usaprocom.com 200015-01B
OPERATION
THERMOSTAT FUNCTION REMOTE CONTROL OPERATION
Setting Desired Room Temperature NOTES
The remote control system can control the The Thermo Feature on the transmitter op-
thermostat when the transmitter is in the erates the appliance whenever the ROOM
THERMO mode. The word ROOM must be TEMPERATURE varies a certain number of
displayed on the screen. degrees from the SET TEMPERATURE.
To set the THERMO MODE and desired room This variation is called the swing or tem-
temperature: perature differential. The normal operating
1. Press the MODE key until the LCD screen cycle of an appliance may be 4 times per
shows the word ROOM. The remote is hour depending on how well the room or
now in the thermostatic mode. home is insulated from the cold or drafts.
The factory setting for the swing number is
2. Press and hold the SET key until the de-
2. This represents a temperature variation of
sired set temperature is reached. The LCD
+/-2F (1C) between SET temperature and
screen set numbers will increase from 45
ROOM temperature, which determines when
to 99 and then restart over at 45.
the fireplace will be activated. The transmitter
3. Release the SET key. The LCD screen has ON and OFF manual functions that are
will display the set temperature for 3 sec- activated by pressing either button on the
onds, then flash the set temperature for face of the transmitter. When a button on the
3 seconds, then LCD screen will default transmitter is pressed the word ON or OF will
to display the room temperature. appear on the LCD screen to show while the
To Change The Set Temperature signal is being sent. Upon initial use, there
1. Press and hold the SET key until the may be a delay of three seconds before the
desired set temperature is reached. The remote receiver will respond to the transmitter.
LCD screen set numbers will increase This is part of the systems design.
from 45 to 99 then restart over at 45.
2. Release the SET key. The LCD screen will
display the set temperature for 3 seconds,
then flash the set temperature for 3 sec-
onds, then the LCD screen will default to
display the room temperature.
3. Press the MODE key to disengage the
thermo mode. The word ROOM on the
LCD screen will not show when the thermo
is not in operation.
Note: The highest SET temperature is
99F (32 C) and the lowest temperature
is 45F (6C).
200015-01B www.usaprocom.com 25
INSPECTING BURNERS
IMPORTANT: Owners should check pilot flame pattern and burner flame pattern often.
Incorrect flame patterns indicate the need for cleaning (see Care and Maintenance,
page 27) or service.
26 www.usaprocom.com 200015-01B
CARE AND MAINTENANCE
200015-01B www.usaprocom.com 27
CARE AND MAINTENANCE
ODS/PILOT
Use a vacuum cleaner, pressurized air, or a Natural Gas
small, soft bristled brush to clean. Burner
A yellow tip on the pilot flame indicates dust Propane/LP
and dirt in the pilot assembly. There is a small Gas Burner
pilot air inlet hole about 2" from where the
pilot flame comes out of the pilot assembly
(see Figure 38). With the unit off, lightly blow
Pilot Air
air through the air inlet hole. You may blow
Inlet Hole
through a drinking straw if compressed air is
not available. Pilot Air Inlet Hole
Figure 38 - Pilot Inlet Air Hole
CABINET
Air Passageways Exterior
Use a vacuum cleaner or pressurized air to Use a soft cloth dampened with a mild soap
clean. and water mixture.
Wipe the cabinet to remove dust.
LOGS
If you remove logs for cleaning, refer to Installing Logs, page 19, to properly replace logs.
Replace log(s) if broken or chipped (dime-size or larger).
28 www.usaprocom.com 200015-01B
TROUBLESHOOTING
200015-01B www.usaprocom.com 29
TROUBLESHOOTING
30 www.usaprocom.com 200015-01B
TROUBLESHOOTING
200015-01B www.usaprocom.com 31
PARTS
MODELS CRHEB24RT AND CRHEB30RT
13-2 13-3
13-1
13-7 13-4
13-6
13-5
(30" Models)
13-5
(24" Models)
13-9
13-10
13-8
(30" Models)
13-12
13-11
13-8 13-13
(24" Models)
11
3
4 TEMP
8
7
6 LE
AR
N
ON
RE
MO
TE
OF
F
10
5
2
9
1
12
32 www.usaprocom.com 200015-01B
PARTS
MODELS CRHEB24RT AND CRHEB30RT
This list contains replaceable parts for your heater. When ordering replacement parts, follow
the instructions listed under Replacement Parts on page 34 of this manual.
PART #
ITEM CRHEB24RT CRHEB30RT DESCRIPTION QTY
1 24ED102B-01 24ED102B-01 Grate Assembly 1
2 PIMSC1-01 PIMSC1-01 Ignitor 1
3 RV83FI-4/9 RV83FI-4/9 Dual Fuel Regulator 1
4 NDD0308-400 NDD0308-400 Dual Fuel ODS/PIlot 1
5 FBB28D11 FBB28D11 Air Shutter Assembly 1
6 YDF06 YDF06 Fuel Selection Device 1
7 MDL304B MDL304B Knob 1
8 CRHEB24/30RT006 CRHEB24/30RT006 Fuel Selection Device Bracket 1
9 MRT-01 MRT-01 Control Valve 1
10 RG04-1M RG04-1M Receiver Box 1
11 RG04-1T RG04-1T Remote Control 1
12 OD-C0889-11 OD-C0889-11 Solenoid 1
13 24ED117B-01 30ED105B-01 Complete Log Set 1
13-1 CRHEB24/30RT301 CRHEB24/30RT301 Log 1 1
13-2 CRHEB24/30RT302 CRHEB24/30RT302 Log 2 1
13-3 CRHEB24/30RT303 CRHEB24/30RT303 Log 3 1
13-4 CRHEB24/30RT304 CRHEB24/30RT304 Log 4 1
13-5 CRHEB24RT305 CRHEB30RT305 Log 5 1
13-6 CRHEB24/30RT306 CRHEB24/30RT306 Log 6 1
13-7 CRHEB24/30RT307 CRHEB24/30RT307 Log 7 1
13-8 CRHEB24RT308 CRHEB30RT308 Log 8 1
13-9 CRHEB24/30RT309 CRHEB24/30RT309 Log 9 1
13-10 CRHEB24/30RT310 CRHEB24/30RT310 Log 10 1
13-11 CRHEB24/30RT311 CRHEB24/30RT311 Log 11 1
13-12 CRHEB24/30RT312 CRHEB24/30RT312 Log 12 1
13-13 CRHEB24/30RT313 CRHEB24/30RT313 Log 13 1
PARTS AVAILABLE - NOT SHOWN
ML064-01 ML064-01 Hardware Packaging 1
HPL604-02 HPL604-02 Embers 1
WZL039-01 WZL039-01 Lava Rock 1
200015-01B www.usaprocom.com 33
REPLACEMENT PARTS
Note: Use only original replacement parts. This will protect your warranty coverage for parts
replaced under warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this product. Model and serial number of your heater
If they cant supply original replacement How heater was malfunctioning
parts, call Customer Service toll free at Type of gas used (Propane/LP or Natural
1-866-573-0674 for referral information. gas/NG)
When calling Customer Service or your dealer, Purchase date
have ready:
Usually, we will ask you to return the defec-
Your name tive part to the factory
Your address
PARTS NOT UNDER WARRANTY
Contact authorized dealers of this product. When calling Customer Service have ready:
If they cant supply original replacement Model number of your heater
part(s) call Customer Service toll free at The replacement part number
1-866-573-0674 for referral information.
ACCESSORIES
Purchase these heater accessories from your local dealer. If they can not supply these acces-
sories, contact ProCom Heating, Inc. at 1-866-573-0674 for information.
34 www.usaprocom.com 200015-01B
SERVICE HINTS
When Gas Pressure Is Too Low
pilot will not stay lit
burners will have delayed ignition
fireplace will not produce specified heat
propane/LP gas supply might be low (propane/LP units only)
You may feel your gas pressure is too low. If so, contact your local gas supplier.
TECHNICAL SERVICE
You may have further questions about installation, operation, or troubleshooting. If so, contact
ProCom Heating, Inc. at 1-866-573-0674.
When calling, please have your model and serial numbers of your heater ready.
200015-01B www.usaprocom.com 35
WARRANTY
KEEP THIS WARRANTY
Model ________________________________
Serial No. _____________________________
Date Purchased ________________________
Keep receipt for warranty verification.
MANUAL DE
FUNCIONAMIENTO E
INSTALACIN DEL
PROPIETARIO
MODELOS
CRHEB24RT Y CRHEB30RT
PFS
US
ADVERTENCIA: Si la informacin contenida en este
manual no se sigue al pie de la letra, se pueden producir
un incendio o una explosin que podran ocasionar daos
a la propiedad, lesiones personales o la prdida de la vida.
No guarde ni utilice gasolina u otros vapores y lquidos
inflamables cerca de este aparato ni de cualquier otro.
QU HACER SI PERCIBE OLOR A GAS
No intente encender ningn aparato.
No toque ningn interruptor elctrico; no use nin-
gn telfono en el edificio.
Llame inmediatamente a su proveedor de gas des-
de el telfono de algn vecino. Siga las instruccio-
nes del proveedor de gas.
Si no puede localizar al proveedor de gas, llame al
departamento de bomberos.
La instalacin y el servicio deben ser realizados por
personal calificado, una agencia de servicio o el
proveedor de gas.
ADVERTENCIA: Este aparato est equipado para
funcionar con gas (propano y natural). No se permite
convertir ms que a gas natural o gas propano.
Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a
nuestro Departamento de Servicio al Cliente al 1-866-573-0674, de lunes a viernes de
8:00 a.m. a 4:30 p.m., Hora del Centro, o enve un correo electrnico a
customerservice@usaprocom.com.
TABLA DE CONTENIDOS
Seguridad................................................. 39 Instalacin................................................ 47
Especificaciones....................................... 41 Funcionamiento........................................ 60
Agencia De Instalacin Calificada............ 41 Inspeccin del calentador......................... 66
Caractersticas Del Producto.................... 42 Cuidado y mantenimiento......................... 67
Identificacin Del Producto....................... 42 Solucin de problemas............................. 69
Normas Locales....................................... 43 Piezas de repuesto................................... 73
Desempaque............................................ 43 Accesorios................................................ 73
Vapor De Agua: Un Producto Derivado Consejos para servicio............................. 73
de Los Calentadores de Habitacin Servicio tcnico........................................ 73
Sin Ventilacin.................................... 43 Piezas....................................................... 74
Aire para combustin y ventilacin........... 44 Garanta................................................... 76
200015-01B www.usaprocom.com 39
SEGURIDAD
4. Mantenga todas las entradas de aire del
ADVERTENCIA: No coloque frente y fondo del calentador limpias y
ropa ni otros materiales inflama- libres de escombros. Esto asegurar aire
bles sobre el aparato ni cerca del suficiente para la combustin.
mismo. Nunca coloque ningn 5. Si el calentador se apaga, no lo vuelva
objeto sobre el calentador. a encender hasta que se le haya pro-
porcionado aire fresco del exterior. Si el
calentador continua apagandose debera
ADVERTENCIA: El juego de ser revisado por personal calificado.
leos alcanza temperaturas muy 6. No haga funcionar el calentador
altas cuando el calentador est donde se utilicen o almacenen lquidos
en funcionamiento. Mantenga a o vapores inflamables
nios y adultos alejados de las en condiciones con mucho polvo
superficies calientes para evitar 7. Apague el calentador antes de usar puli-
quemaduras o que la ropa se dores de muebles, ceras, limpiadores de
encienda. El calentador perma- alfombras o productos parecidos. Si se
necer caliente durante algn calientan, los vapores que se despren-
den de estos productos pueden producir
tiempo despus de que se ha un residuo de polvo blanco dentro de la
apagado. Permita que la super- caja del calentador, o en las paredes y los
ficie se enfre antes de tocarla. muebles adyacentes.
8. No use este calentador si alguna de sus
ADVERTENCIA: Supervise partes estuvo sumergida en agua. Llame
cuidadosamente a los nios inmediatamente a un tcnico de servicio
pequeos cuando estn en la para que inspeccione el calentador y para
habitacin en la que se encuen- que remplace las piezas del sistema de
control o los controles de gas que hayan
tra el calentador. estado sumergidos en agua.
9. Apague el calentador y djelo enfriar
ADVERTENCIA: Debe operar antes de cualquier reparacin. Slo un
el juego de leos con la rejilla tcnico calificado debe realizar el mante-
colocada en su lugar. nimiento o reparar el calentador.
1. No ponga los tanques de suministro de 10. Hacer funcionar el calentador a alturas
gas propano o gas LP dentro de ninguna superiores a 1,371 m (4,500 pies) puede
estructura. Site los tanques de suminis- ocasionar que el piloto se apague.
tro gas de gas propano/LP en el exterior. 11. Para evitar problemas de rendimiento en
2. Este calentador no debe ser instalado en los modelos de gas propano/LP, no use
un dormitorio o un bao. tanques de gas propano/LP de menos de
45 kg (100 libras) de capacidad.
3. Este calentador necesita ventilacin con
aire fresco del exterior para funcionar 12. No utilice este calentador como un
correctamente. Este calentador tiene un calentador de lea. Use slo los leos
sistema de apagado de seguridad con proporcionados con el calentador.
deteccin de agotamiento de oxgeno 13. Los combustibles slidos no deben que-
(ODS). El ODS apaga el calentador cuan- marse en una chimenea en el que est
do no hay suficiente aire fresco. Consulte instalado el juego de leos de gas sin
Aire para combustin y ventilacin en ventilas. No utilice este calentador para
la pgina 44. Si el calentador contina cocinar alimentos o quemar papel u otro
apagndose, consulte Solucin de pro- tipo de combustible slido.
blemas, en la pgina 69. 14. Para evitar que se produzca holln, siga
las instrucciones (consulte la seccin
Cuidado y mantenimiento, pgina 67).
40 www.usaprocom.com 200015-01B
SEGURIDAD
15. No agregue ms leos ni ornamentos, 17. Si la chimenea tiene puertas de vidrio,
como pias, vermiculita o lana mineral, nunca use este calentador con las puertas
pues ellos facilitan la produccin de holln. cerradas. Si lo hace, el calor se acumular
No agregue roca de lava alrededor de dentro de la chimenea y har que el vidrio
la base. La roca y los desechos pueden estalle. Si la abertura de la chimenea tiene
caer en el rea de control del calentador. respiraderos en la base, debe abrirlos
Despus de realizarle mantenimiento antes de usar el juego de leos. Siempre
al calentador, siempre coloque la malla use el calentador con las puertas de vidrio
antes de usarlo. completamente abiertas.
16. Este calentador de leos est diseado 18. No haga funcionar el calentador si alguno
para no producir humo. Si pareciera que de los leos est roto. No haga funcionar
los leos producen humo, apague el ca- el calentador si alguno de los leos est
lentador y llame a un tcnico calificado. astillado (del tamao de una moneda de
Nota: durante el primer uso, es posible 10 centavos o ms grande).
que haya un poco de humo debido al
curado de los leos y a la combustin de
los residuos de fabricacin.
ESPECIFICACIONES
Modelos CRHEB24RT y CRHEB30RT
Tipo de gas Natural Propano o gas LP
Encendido Piezoelctrico Piezoelctrico
ndice de entrada 35,000 BTU/hr 35,000 BTU/Hr
Presin del tubo mltiple 4" de c.a. 9" de c.a.
Presin de entrada de gas (pulg. de c.a.) Mxima 10.5" Mxima 14"
(*Para propsitos de ajuste de entrada) Mnima 5" Mnima 11"
200015-01B www.usaprocom.com 41
CARACTERSTICAS DEL PRODUCTO
Este juego de leos fue probado y aprobado SISTEMA DE ENCENDIDO
por la norma ANSI Z21.11.2 para los calenta- PIEZOELCTRICO
dores sin ventilacin y se puede usar con el El calentador cuenta con un sistema de con-
regulador de tiro cerrado. Los normas locales trol piezoelctrico. Requiere una (1) batera
y estatales de algunas reas prohben el uso AAA (incluida).
de calentadores de gas sin ventilas.
2 OPCIONES DE GAS
PILOTO DE SEGURIDAD DISPONIBLES
El calentador posee un piloto que cuenta El calentador est diseado para funcionar
con un sistema de apagado de seguridad con gas propano o con gas natural. El calenta-
por medio de un sensor de agotamiento de dor es enviado de fbrica listo para conectar-
oxgeno (ODS). El sensor de agotamiento de se a gas propano. Para cambiarlo fcilmente
oxgeno del piloto apaga el calentador si no a gas natural, el instalador calificado debe
hay suficiente cantidad de aire fresco. seguir las instrucciones de la pgina 55 y las
indicaciones que aparecen en el calentador.
42 www.usaprocom.com 200015-01B
NORMAS LOCALES
Instale y use el calentador con cuidado. Siga
todas las normas locales. A falta de normas loca- Estado de Massachusetts: La instalacin
les, utilice la ltima edicin del Cdigo Nacional la debe realizar un plomero o un instalador
de Gas Combustible, ANSI Z223.1/NFPA 54*. de gas con licencia para ejercer en el esta-
do de Massachusetts.
*Disponible en:
Los vendedores de calentadores com-
American National Standards Institute. Inc.
plementarios de interiores a base de gas
1430 Broadway
propano o de gas natural y sin ventilacin
New York, NY 10018, EE.UU.
deben proporcionar a cada cliente una
National Fire Protection Association, Inc. copia del 527 CMR 30 al realizar la venta.
Batterymarch Park
En el estado de Massachusetts la manija
Quincy, MA 02269, EE.UU.
del gas debe ser una manija tipo T. El es-
Nota: este calentador esta diseado para tado de Massachusetts requiere que el co-
operar sin ventilas. Normas locales y esta- nector flexible no exceda de 3 pies de largo.
tales de algunas reas prohben el uso de
calentadores de gas sin ventilas.
DESEMPAQUE
1. Quite los leos y la base ensamblada del 2. Retire todo el empaque de proteccin
quemador de la caja. NOTA: no levante la colocado en los leos y el calentador para
base ensamblada del quemador mediante su envo.
los quemadores, ya que esto podra daar 3. Verifique que no se hayan producido da-
el calentador. Siempre maneje la base os en ninguno de los artculos durante el
ensamblada mediante la rejilla. transporte. Si el calentador est daado,
informe de inmediato al distribuidor a
quien se lo compr.
200015-01B www.usaprocom.com 43
AIRE PARA COMBUSTIN Y VENTILACIN
calor en las casas. Los propietarios de casas
ADVERTENCIA: Este calen- aislan y sellan alrededor de las ventanas y
tador no debe instalarse en un puertas para mantener el aire fro afuera y el
espacio confinado ni en una cons- aire caliente adentro. Durante los meses de
truccin inusualmente sellada, a calor, los propietarios de casas desean que
sus hogares estn lo ms hermtico posible.
menos que se hayan tomado las
Aunque es bueno hacer que su hogar sea
medidas necesarias para propor-
eficiente en el ahorro de energa, tambin
cionar el aire adecuado para la es necesario que se ventile. Es necesario
combustin y la ventilacin. Lea que entre aire fresco a su casa. Todos los
las instrucciones siguientes para aparatos que queman combustible necesi-
asegurarse de que su hogar cuen- tan aire fresco para tener una combustin y
te con la cantidad adecuada de ventilacin adecuadas.
aire fresco para ste y otros apa- Los ventiladores de expulsin de aire, las
ratos que queman combustible. chimeneas, las secadoras de ropa y los apa-
ratos que queman combustible toman aire
Las casas actuales estn diseadas para de la casa durante su funcionamiento. Usted
ser ms eficientes que nunca en el ahorro debe proporcionar la cantidad adecuada de
de energa. Los nuevos materiales, un aire fresco para estos aparatos. Esto asegura
mejor aislamiento y los nuevos mtodos de que la ventilacin de los aparatos que queman
construccin ayudan a reducir la prdida de combustible sea la adecuada.
44 www.usaprocom.com 200015-01B
AIRE PARA COMBUSTIN Y VENTILACIN
Espacio confinado y no confinado
El Cdigo Nacional de Gas Combustible, instalados en ese espacio. Las habitaciones
ANSI Z223.1/NFPA 54, define el espacio con- que se comunican directamente con el espa-
finado como aqul cuyo volumen es menor de cio en el que estn instalados los aparatos*,
4.8m3 por kw (50 pies3 por 1,000 BTU/h) de mediante aberturas que no tienen puertas, se
clasificacin de entrada agregada de todos consideran parte del espacio no confinado.
los aparatos instalados en ese espacio, y * Se considera que las habitaciones adyacen-
define el espacio no confinado como aqul tes estn comunicadas slo si hay accesos
cuyo volumen es mayor de 4.8 m3 por kw sin puertas o si hay rejillas de ventilacin
(50 pies3 por 1,000 BTU/h) de clasificacin entre ellas.
de entrada agregada de todos los aparatos
DETERMINACIN DEL FLUJO DE AIRE FRESCO PARA UBICAR EL CALENTADOR
Cmo determinar si tiene un espacio confinado o no confinado
Utilice esta hoja de trabajo para determinar * No incluya los aparatos de gas con ven-
si tiene un espacio confinado o no confinado. tilacin directa. El sistema de ventilacin
Espacio: Incluye la habitacin en la que se directa toma el aire para combustin del
va instalar el calentador mas todas las ha- exterior y ventila hacia el exterior.
bitaciones adyacentes que tengan accesos Ejemplo:
30,000 BTU/h
sin puerta o rejillas de ventilacin entre ellas. Calentador de agua a gas _ ______
1. Determine el volumen del espacio (largo Calentador sin ventilacin +_ ______
26,000 BTU/h
x ancho x altura). Total ______
=_ 56,000 BTU/h
4. Compare la cantidad mxima de BTU/h
Largo x ancho x altura =__________ m3
que el espacio puede admitir con la can-
(pies3) (volumen del espacio)
tidad real de BTU/h que se utiliza.
Ejemplo: tamao del espacio 6.10 m (20
_ ______ BTU/h (mximo que el espacio
pies) de largo x 4.88 m (16 pies) de ancho
puede admitir)
x 2.44 m (8 pies) de altura del techo =
72.49m3 (2560 pies3) (volumen del espacio) _ ______ BTU/h (cantidad real de BTU/h
que se utiliza)
Si se proporciona ventilacin adicional a
las habitaciones adyacentes por medio de Ejemplo: 51,200 BTU/h (cantidad mxima
rejillas o aberturas, agregue el volumen que el espacio puede admitir)
de stas al volumen total del espacio. 79,000 BTU/h (cantidad real de
2. Multiplique el volumen del espacio en pies3 BTU/h que se utiliza)
por 20 para determinar la cantidad mxima El espacio del ejemplo anterior es un espacio
de BTU/h que el espacio puede admitir. confinado, ya que la cantidad real de BTU/h
_ _______ (volumen del espacio en pies3) utilizadas es mayor que la cantidad mxima
x 20 = (cantidad mxima de BTU/h que el de BTU/h que el espacio puede admitir. Se
espacio puede admitir) debe proporcionar aire fresco adicional. Sus
opciones son las siguientes:
Ejemplo: 72.4 m3 (2,560 pies3) (volumen
del espacio en pies3) x 20 = 51,200 (can- A. Vuelva a calcular la hoja de trabajo, agregan-
tidad mxima de BTU/h que el espacio do el espacio de una habitacin adyacente.
puede admitir) Si el espacio adicional genera un espacio no
confinado, quite la puerta de la habitacin
3. Agregue la cantidad de BTU/h de todos
adyacente o instale rejillas de ventilacin
los aparatos que queman combustible en
entre las habitaciones. Consulte Aire del
ese espacio.
interior de la construccin para ventilacin.
Calentador sin ventilacin __________ BTU/h B. Ventile la habitacin directamente desde
Calentador de agua de gas* __________ BTU/h el exterior. Consulte Aire del exterior para
Horno de gas __________ BTU/h ventilacin.
Calentador de gas C. Instale un calentador de menos BTU/h si
con ventilacin __________ BTU/h una cantidad menor de BTU/h hace que la
Leos para chimenea de gas __________ BTU/h habitacin sea no confinada. Si la cantidad
Calentador de agua de gas __________ BTU/h real de BTU/h que se utiliza es menor que
Otros aparatos de gas* +_________ BTU/h la cantidad mxima que el espacio puede
Total =_________ BTU/h admitir, el espacio es no confinado. No ne-
cesitar ventilacin adicional con aire fresco.
200015-01B www.usaprocom.com 45
AIRE PARA COMBUSTIN Y VENTILACIN
30.48 cm
(12")
Salida de aire tico ventilado
Rejillas de
Rejillas de ventilacin Salida
ventilacin de aire
hacia un O quite hacia un cuarto Al tico
cuarto la puerta adyacente, opcin 2
adyacente, hacia
opcin 1 el cuarto
adyacente, Al espacio
opcin transitado
Entrada
3 de aire
Entrada Espacio transitado
de aire ventilado
46 www.usaprocom.com 200015-01B
INSTALACIN
200015-01B www.usaprocom.com 47
INSTALACIN
IMPORTANTE: Los calentadores sin ventila- Distancias mnimas de los
cin aaden humedad al aire. Aunque esto alrededores para materiales
es benfico, la instalacin del calentador en combustibles, paredes y techo
habitaciones sin suficiente aire de ventilacin A. Las distancias mnimas desde los lados
puede ocasionar la formacin de moho debido del gabinete de la chimenea hacia cual-
al exceso de humedad. Consulte Aire para quier material combustible y paredes de-
Combustin y Ventilacin en la pgina 44. ben ser las que se indican en el diagrama
Antes de ensamblar u operar el producto, ase- de la figura 4.
grese de tener todas las piezas. Compare las
B. Las distancias mnimas a partir de la parte
piezas con la lista del contenido del paquete y
la Figura 1 de la pagina 6. No intente ensam- superior de la abertura del calefactor
blar, instalar ni usar el producto si falta alguna hacia el techo no deben ser menores de
pieza o si stas estn daadas. Pngase en 1 m (42").
contacto con el Departamento de Servicio al
Cliente para obtener piezas de repuesto
Antes de instalar el calentador, asegrese de
que tiene los siguientes materiales:
El paquete de partes (se proporciona junto
con el calentador)
Taladro elctrico con broca de 3/16"
Destornillador Phillips
VERIFIQUE EL TIPO DE GAS
Asegrese de que el suministro de gas es
apropiado para el calentador. De lo contrario, *
llame al distribuidor donde compr el calen- *Mnimo 40.64 cm (16") de la pared lateral
tador para el calentador de tipo adecuado. Figura 4 - Distancia mnima del
ESPACIO LIBRE PARA combustible a la pared
MATERIALES COMBUSTIBLES
Distancias mnimas para materiales
ADVERTENCIA: Mantenga las no combustibles
distancias mnimas. Si es posible, Cuando no se utiliza repisa
proporcione distancias mayores Nota: si utiliza repisa contine en Cuando
respecto al suelo, al techo y a las se utiliza repisa. Si no utiliza repisa, siga la
informacin en esta pgina.
paredes adyacentes. Mida desde el
El material que est arriba de la abertura
punto ms alejado del calentador. de la chimenea debe ser no combustible. El
Distancia de separacin mnima entre material no combustible, (por ejemplo, can-
la chimenea y materiales combustibles tera, mrmol, azulejo, etc.), debe ser de por
Pared lateral 40,64 cm (16"), lo menos 1.27 cm (1/2") de ancho. Cuando
Techo 106,68 cm (42"), Anterior 91,4 cm (36") utilice lmina metlica debe colocar material
no combustible detrs de sta. El material
REQUERIMIENTOS DEL TAMAO
no combustible debe abarcar por lo menos
DEL LEO
30.4cm (12") hacia arriba. Consulte la figura
Tamao Mnimo De Fogn
61 cm (24") Juego de leos: 5, pagina 13, para ver las distancias mnimas.
Altura 50,8 cm (20"),
Profundidad 31,8 cm (15"),
Ancho parte anterior 71.1 cm (28"),
Ancho parte posterior 58,4 cm (23")
76,2 cm (30") Juego de leos:
Altura 50,8 cm (20"),
Profundidad 31,8 cm (15"),
Ancho parte anterior 36,4 cm (34"), Ancho
parte posterior 58,4 cm (23")
48 www.usaprocom.com 200015-01B
INSTALACIN
Cuando se utiliza repisa
Requisitos para una instalacin segura
(A) 30.4 cm (12") o ms: Se puede utilizar El material que est arriba de la abertura de la
material no combustible. chimenea debe ser no combustible. El material
(A) Entre 20.3 cm (8") y 30.4 cm (12"): no combustible, (por ejemplo, cantera, mr-
Instale la cubierto. mol, azulejo, etc.), debe ser de por lo menos
(A) Menos de 20.3 cm (8"): El material no 1.27 cm (1/2") de ancho. Cuando utilice lmi-
combustible debe abarcar por lo menos na metlica debe colocar material no combus-
20.3 cm (8"). Consulte Entre 20.3 cm tible detrs de sta. El material no combusti-
(8") y 30.4 cm (12"), arriba. Si el material ble debe abarcar por lo menos 20.3 cm (8")
no puede cubrir la distancia debe hacer hacia arriba. Si el material no combustible
funcionar el calentador con la compuerta cubre menos de 30.4 cm (12"), entonces debe
del tiro de la chimenea abierta. instalar el accesorio de cubierta de chimenea.
Incluso cuando el material no combustible
Material cubra 30.4 cm (12"), posiblemente necesite
resistente el accesorio de cubierta para que el calor no
al calor llegue a la repisa. Consulte las figuras 5, 6 y
Distancia el 7 para obtener las distancias mnimas.
material no
combustible
45.7 cm (18")
50.8 cm (20")
30.4 cm (12")
38.1 cm (15")
Mnimo para
20.3 cm (8")
(pulgadas)
material no (A) combustible
combustible
Mnimas
30.4 cm 45.7 cm 50.8 cm 55.8 cm 61 cm
(12") (18") (20") (22") (24") Parte
superior
Parte de la
Altura mnima Distancias al
superior de abertura
del material la abertura Cubierta Distancias de la
fondo de la
no combustible de la al fondo de
repisa
chimenea
chimenea
la repisa
Material
35.5 cm (14") combustible
Mn. Chimenea
Material
combustible
12.7 cm
Material no combustible (5") mnimo
Figura 8 - Distancias mnimas de la
chimenea cuando se instala a nivel del Figura 9 - Distancias mnimas para la
suelo chimenea sobre suelo combustible
50 www.usaprocom.com 200015-01B
INSTALACIN
SELECCIN DE GAS
Para cambiar de gas propano a gas
Este aparato viene confi- natural:
gurado de fbrica para gas 1. Retire los 2 tornillos de la placa de la
propano/LP. No se requieren cubierta situados en el lado izquierdo del
cambios para la conexin a calentador (consulte la Figura 10).
gas propano/LP. Slo un tc- 2. Para GAS NATURAL, presione la perilla
nico calificado o un tcnico en con un destornillador plano con hoja de
un cuarto de grosor y gire la perilla en
mantenimiento pueden realizar direccin de las manecillas del reloj
la seleccin del gas y la conexin hasta que la perilla quede fijada en la
al suministro de gas. posicin NG (consulte la Figura 10). El
dispositivo de seleccin de combustible
PRECAUCIN: Se prohbe debe estar fijo en la posicin NG. No use
instalar dos lneas de gas al el calentador con la perilla ubicada entre
mismo tiempo. No abra la cu- las dos posiciones.
3. Coloque la cubierta sobre el dispositivo
bierta mientras la mquina est
de seleccin de combustible y vuelva a
en funcionamiento. instalar los tornillos.
4. Retire el tapn hexagonal (con la llave
PRECAUCIN: Para evitar provista) de la entrada de gas natural del
fugas de gas en la entrada del regulador (consulte la Figura10). Coloque
regulador, un tcnico calificado el tapn hexagonal en la entrada LP del
o un tcnico en mantenimiento regulador. Instale la tubera de gas en
debe usar un tapn hexagonal la entrada del regulador de gas natural.
Utilice sellador de roscado para evitar
con sellador. fugas.
200015-01B www.usaprocom.com 51
INSTALACIN
Para cambiar de gas natural a gas propano
1. Retire los 2 tornillos de la placa de la 4. Retire el tapn hexagonal (con la llave
cubierta situados en el lado izquierdo del provista) de la entrada de gas propano/
calentador (consulte la Figura 11). LP del regulador (consulte la Figura11).
2. Para GAS PROPANO, presione la perilla Coloque el tapn hexagonal en la entrada
con un destornillador plano con hoja de NG del regulador. Instale la tubera de
un cuarto de grosor y gire la perilla en gas en la entrada del regulador de gas
direccin contraria a las manecillas del LP. Utilice sellador de roscado para evitar
reloj hasta que la perilla se fije en fugas.
la posicin LP (consulte la Figura 11). El Conexin Perilla de seleccin
dispositivo de seleccin de combustible del gas de combustible
debe estar fijo en la posicin LP. No use LP
el calentador con la perilla ubicada entre NG
las dos posiciones.
3. Coloque la cubierta sobre el dispositivo
LP
de seleccin de combustible y vuelva a NG
instalar los tornillos. Tapn
hexagonal
El lado Left
izquierdo
Side ofdel calentador
Heater
Figura 11 - Ajustes para Gas Propano/LP
52 www.usaprocom.com 200015-01B
INSTALACIN
2. Marque las ubicaciones de los tornillos
a travs de los orificios de la abrazadera
de montaje (consulte la Figura 12). Si
lo instala en una chimenea con la parte
inferior de ladrillo, marque las ubicaciones
de los tornillos en la unin de mortero de
los ladrillos.
3. Retire la base del calentador de la chime-
nea.
4. Taladre orificios en las ubicaciones mar-
cadas con una broca de 3/16".
5. Fije la base ensamblada al piso de la
chimenea mediante dos tornillos para
mampostera (en el paquete de aditamen-
Tornillo para
tos (consulte la Figura 12).
mampostera
6. Conectar a la alimentacin de gas. Con-
sulte Conexin al suministro de gas.
Figura 12 - Instalacin de la base en el
suelo de la chimenea
200015-01B www.usaprocom.com 53
INSTALACIN
manguera flexible para gas (revise los
PRECAUCIN: Utilice nica- cdigos locales)
mente tubera nueva, de hierro * Una vlvula de cierre de equipo con diseo
negro o de acero. En algunas certificado por la CSA con rosca tipo NPT
de 1/8 es una alternativa aceptable como
reas se puede utilizar tubera de conexin para el medidor de prueba. La vl-
cobre con interior galvanizado. vula opcional de cierre de equipo con diseo
Consulte los cdigos locales. certificado por la CSA la puede adquirir con
Use tubera de 1/2" de dimetro su distribuidor.
interior, o mayor, para que el Dimetros usuales de tubera de
volumen de gas al calentador entrada
sea el adecuado. Si la tubera es Utilice tuberas de hierro negro de 3/8" o ms
grandes. La instalacin debe incluir la vlvula
demasiado angosta, se producir de cierre del equipo, la unin y el tapn con
una prdida indebida de presin. rosca NPT de 1/8". Site el conector con rosca
NPT a su alcance para realizar la conexin
PRECAUCIN: Revise la del medidor de prueba. El conector tipo NPT
presin de la lnea de gas natural se debe conectar en direccin del suministro
desde el calentador (consulte la figura 13,
antes de conectar el calentador pagina 55).
a la lnea. La presin de la lnea IMPORTANTE: Instale una vlvula de cierre
de gas no debe ser superior del equipo en un lugar que sea accesible. La
a26,67cm (10.5") de c.a. Si la vlvula de cierre del equipo es para abrir o
presin de la lnea de gas es cerrar el suministro de gas al aparato.
Aplique una pequea cantidad de sellador de
superior, podra daarse el re-
tubera a las roscas NPT macho. Esto evitar
gulador del calentador. que el exceso de sellador entre a la tubera. El
exceso de sellador en la tubera puede ocasio-
PRECAUCIN: Evite daar el nar que las vlvulas del calentador se tapen.
regulador. Sostenga el regulador Para gas propano/LP, el instalador debe pro-
de gas con una llave cuando lo veer un regulador externo. El regulador externo
conecte a la tubera de gas y/o reducir la presin del gas entrante. Debe
reducir la presin del gas entrante de manera
a las conexiones. que est entre 11" y 14" de c.a. Si no reduce
la presin del gas entrante, se pueden producir
ADVERTENCIA: Use sellador daos al regulador del calentador. Instale el
para tubera que sea resistente al regulador externo con la ventila apuntando
gas (Propane/LP o Gas Natural). hacia abajo. Como se muestra en la figura 14,
pagina 55. El apuntar la ventila hacia abajo la
Antes de instalar el calentador, asegrese de te- protege de la lluvia helada o aguanieve.
ner los elementos que se indican a continuacin. Instale la trampa de sedimentos en la lnea de
regulador externo para gas propano/LP suministro como se muestra en la figura 13,
(proporcionado por el tcnico capacitado que pagina 55. Site la trampa de sedimentos de
realiza la instalacin) manera que se pueda tener acceso a ella para
tubera (consulte los cdigos locales), limpieza. Site la trampa de sedimentos donde
sellador (resistente al gas natural y gas sea poco probable que los materiales atrapados
propano/LP), en ella se congelen. La trampa de sedimentos
vlvula de cierre del equipo*, atrapa humedad y contaminantes. Esto evita
conexin para medidor de prueba*, que los sedimentos lleguen a los controles del
unin de terminal con conexin a tierra, calentador. Si la trampa de sedimentos no se
trampa de sedimentos, instala o se instala incorrectamente, el calenta-
unin T, dor podra no funcionar correctamente.
llave para tubera,
54 www.usaprocom.com 200015-01B
INSTALACIN
56 www.usaprocom.com 200015-01B
INSTALACIN
INSTALACIN DEL RECEPTOR DEL CONTROL REMOTO
El receptor del control remoto funciona 1. Retire la tapa de la batera en el receptor,
con cuatro bateras tamao AA de 1,5 V como se muestra en el cuadro. Instale
(incluidas). Use bateras ALCALINAS para cuatro bateras de tamao AA en el re-
una duracin ms prolongada de stas y un ceptor (consulte la Figura 18).
rendimiento mximo del microprocesador. 2. Localice los cables rojo y negro de la
IMPORTANTE: es esencial usar bateras vlvula solenoide en el lado derecho
nuevas o completamente cargadas para del calentador. Conecte los cables al
un correcto funcionamiento del receptor del receptor, rojo con rojo, negro con negro
control remoto, ya que el consumo de energa (consulte la Figura 18).
del solenoide es mayor que el de sistemas de 3. Coloque el receptor al lado del juego de
control remoto estndar. leos (consulte la Figura 18).
58 www.usaprocom.com 200015-01B
INSTALACIN
4. Inserte las clavijas en la parte inferior del Leo #5
Leo #6
leo #5 en el agujero del leo #4, con el
otro extremo colocado en la rejilla de base Leo #7
(consulte Figura 23).
5. Inserte las clavijas en la parte inferior del
leo #6 en el agujero del leo #4, con el
otro extremo colocado en la rejilla de base
(consulte Figura 23).
6. Inserte las clavijas en la parte inferior del
leo #7 en el agujero del leo #4, con el
otro extremo colocado en la rejilla de base
(consulte Figura 23).
7. Inserte las clavijas en la parte inferior del Figura 23 - Instalacin de leos #5, #6 y #7
leo #8 en el agujero del leo #3. Apoye
el borde frontal sobre el leo #4 (consulte
Figura 24). Leo #9
8. Girar el leo #9 como se muestra en la Leo #8
Figura 26. Insertar el leo #9 en frente
del soporte de registro trasera, de la
rejilla de base, insertando las clavijas en
la parte trasera de registro, en la ranura
del soporte de registro trasera (consulte
Figura 24).
9. Coloque roca de lava en el suelo en la
parte delantera del quemador (consulte
Figura 25).
10. Coloque el leo #10, #11, #12 y #13 en la
parte superior de la roca de lava en frente
del quemador (consulte Figura 26).
Figura 24 - Instalacin de leos #8 y #9
IMPORTANTE: Asegrese de que los regis-
tros no cubren los orificios del quemador. Es
muy importante instalar los leos exacta-
mente como se indica en las instrucciones.
No modifique los leos. Utilice slo los leos
suministrados con el calentador.
200015-01B www.usaprocom.com 59
FUNCIONAMIENTO
POR SU SEGURIDAD, LEA ESTO ANTES DE
ENCENDER EL CALENTADOR
Llame inmediatamente a su provee-
ADVERTENCIA: No seguir dor de gas desde el telfono de algn
estas instrucciones al pie de la vecino. Siga las instrucciones del
letra puede resultar en incen- proveedor de gas.
dio o explosin que produzcan Si no puede localizar al proveedor
daos a la propiedad, lesiones de gas, llame al departamento de
bomberos.
fsicas o la muerte. C. Utilice nicamente la mano para pre-
A. Este aparato tiene un piloto que se sionar o girar la perilla de control de
debe encender manualmente. Cuando gas. Nunca utilice herramientas. Si no
encienda el piloto, siga estas instruc- puede presionar o girar la perilla ma-
ciones al pie de la letra. nualmente, no intente repararla, llame
B. ANTES DE ENCENDERLO compruebe a un tcnico de servicio capacitado.
que alrededor del aparato no hay olor Forzarla o tratar de repararla pueden
a gas. Asegrese de oler tambin cerca producir un incendio o una explosin.
del suelo, ya que algunos gases son D. No use este aparato si alguna de sus
ms pesados que el aire y se asientan partes estuvo sumergida en agua.
cerca del suelo. Llame inmediatamente a un tcnico ca-
QU HACER SI PERCIBE OLOR A GAS pacitado de servicio para que inspec-
cione el aparato y remplace las piezas
No intente encender ningn aparato.
del sistema de control y los controles
No toque ningn interruptor elctrico; de gas que hayan estado sumergidos
no use ningn telfono en el edificio. en agua.
INSTRUCCIONES DE ENCENDIDO
3. Instale dos (2) bateras AAA en el control
ADVERTENCIA: Debe operar remoto (consulte pagina 62).
este calentador con la rejilla co- 4. Asegrese de que el interruptor deslizable
locada en su lugar. Asegrese de en la parte frontal de la caja receptora est
que la rejilla est instalado antes enlaposicin REMOTE.
de hacer funcionar el calentador. 5. Asegrese de que la vlvula de cierre del
equipo est completamente abierta.
AVISO: Durante el funcionamien- 6. Presione levemente la perilla de control y
grela en direccin de las manecillas del
to inicial de un calentador nuevo,
reloj hasta la posicin OFF.
los leos despedirn un olor a
papel quemado. Tambin habr
llamas anaranjadas. Abra el re-
gulador del tiro o una ventana
para ventilar el olor. Esto durar
solamente unas horas.
1. ALTO! Lea la informacin de seguridad.
2. Desatornille la tapa del encendedor e
instale una batera AAA con el nodo (+)
apuntando hacia afuera. Vuelva a colocar
la tapa. Perilla de control
Botn del encendedor
Figura 26 - Botn de encendido y perilla
de control
60 www.usaprocom.com 200015-01B
FUNCIONAMIENTO
7. Espere cinco (5) minutos a que se disipe 10. Una vez que haya encendido el piloto
el gas. Luego acrquese para ver si per- mantenga la perilla de control presionada
cibe olor a gas, incluso cerca del suelo. Si durante 30 segundos. Despus de los 30
percibe olor a gas, DETNGASE! Siga el segundos, suelte la perilla de control. Si
punto B en la informacin de seguridad la perilla de control no aparecer cuando
en la pgina 18. Si no percibe olor a gas, se libera, pngase en contacto con un
contine con el siguiente paso. tcnico de servicio calificado o proveedor
8. Presione levemente la perilla de control de gas para las reparaciones.
en sentido contrario al de las manecillas Nota: si el piloto se apaga, repita los
del reloj hasta la posicin PILOT pasos 7 al 10. Este calentador tiene un
(piloto). Presione la perilla de control sistema de bloqueo de seguridad. Espere
durante cinco (5) segundos un (1) minuto antes de encender el piloto
Nota: La perilla de control se debe presio- nuevamente.
nar durante 30 segundos o ms la primera 11. Gire la perilla de control en sentido con-
vez que se hace funcionar el calentador trario al de las manecillas del reloj
despus de conectarlo al suministro de a la posicin de encendido. El quemador
gas. Esto permitir que el aire salga del principal deber encenderse.
sistema de gas. En caso que el piloto no Nota: Espere un minuto despus de
encienda, consulte la seccin Solucin apagar el calentador para permitir que la
de problemas, en la pgina 69. Tambin, vlvula decontrol se restablezca antes de
llame a un tcnico de servicio calificado o encender nuevamente la unidad.
a su proveedor de gas para que realicen 12. Presione el BOTN LEARN en la parte
las reparaciones necesarias. Hasta que frontal de la caja del receptora hasta que
se hagan las reparaciones, encender el escuche un bip (ver Programacin del
piloto con un fsforo. control remoto y el receptor, pgina 62).
Si al soltar la perilla de control sta no 13. Presione el botn de encendido en el
regresa a su posicin original, llame a transmisor del control remoto para en-
un tcnico de servicio calificado o a su cender el quemador. (Esto permitir que
proveedor de gas para que realicen las se programe, el transmisor y el receptor).
reparaciones necesarias.
Nota: Si se pierde o daa el transmisor,
9. Presione la perilla de control y, al mis- puede utilizarse el interruptor deslizable
mo tiempo, oprima y suelte el botn de en el receptor para operar el calentador.
encendido. Esto encender el piloto. El
piloto est instalado en la parte posterior
PRECAUCIN: No intente
del quemador. El piloto puede ser visto
a travs de la parrilla En caso nece- ajustar los niveles de calefac-
sario, contine oprimiendo el botn de cin por medio de la vlvula de
encendido hasta que el piloto encienda. cierre del equipo.
Nota: Si el piloto no se mantiene encen-
dido, consulte la seccin Solucin de ADVERTENCIA: Si el tipo
problemas, en la pgina 69. Tambin de entrada de gas es NG, ase-
contacte un tcnico de servicio calificado
o proveedor de gas para las reparaciones.
grese de que el quemador del
Encienda el piloto con un fsforo hasta piloto NG encienda. Si el tipo de
que se realicen las reparaciones. Para entrada de gas es LP, asegrese
encender el piloto con un fsforo. Con- de que el quemador del piloto
sulte el Procedimiento para encendido LP encienda.
manual, en la pgina 62.
200015-01B www.usaprocom.com 61
FUNCIONAMIENTO
CMO CERRAR EL SUMINISTRO DE GAS AL APARATO
Cmo apagar el calentador Cmo apagar slo el quemador el
Gire la perilla de control en direccin de la piloto (el piloto permanece encendido)
manecillas del reloj hasta la posicin Gire la perilla de control en direccin de la
OFF (apagado). manecillas del reloj hasta la posicin
PILOT (piloto).
OF
TE
MO
RE
ON
6
Figura 30 - Pantalla de Control Remoto
64 www.usaprocom.com 200015-01B
FUNCIONAMIENTO
NOTAS DEL FUNCIONAMIENTO DEL CONTROL REMOTO:
La funcin termosttica del transmisor opera entre la temperatura ESTABLECIDA y tem-
el electrodomstico cada vez que la TEM- peratura AMBIENTE, esto determina cundo
PERATURA AMBIENTE vara una cierta se activar la chimenea. El transmisor cuenta
cantidad de grados con respecto a la TEMPE- con funciones manuales de ON y OF que
RATURA ESTABLECIDA. Esta variacin se se activan presionando cualquiera de sus
llama FLUCTUACIN o DIFERENCIAL DE teclas. Mientras se presiona un botn del
TEMPERATURA. El ciclo de funcionamiento transmisor, aparece la palabra ON u OF en
normal de un aparato puede ser 4 veces por la pantalla LDC para mostrar el envo de la
hora dependiendo de lo bien que la habitacin seal. Despus del uso inicial, es posible que
o el hogar se asla del fro o las corrientes el receptor remoto responda al transmisor con
de aire. El ajuste de fbrica para el nmero una demora de tres segundos. Este compor-
de fluctuacin es 2, lo que representa una tamiento forma parte del diseo del sistema.
variacin en la temperatura de +/-2 F (1C)
200015-01B www.usaprocom.com 65
INSPECCIN DE LOS QUEMADORES
IMPORTANTE: El propietario debe revisar frecuentemente los patrones de la llama del
piloto y de la llama del quemador. Patrones de llama incorrectos indican la necesidad de
limpieza o servicio de mantenimiento (consulte Cuidado y mantenimiento, pgina 67).
rrar el suministro de gas al aparato, en la Ms de More Than 8" Above Top of Logs
8" sobre
pgina 62). la parte
consulte Solucin de problemas, en la superior
pgina 69 el leos
200015-01B www.usaprocom.com 67
CUIDADO Y MANTENIMIENTO
ODS/PILOTO
Utilice una aspiradora, aire comprimido o Quemador de
un cepillo pequeo, de cerdas suaves para gas natural Quemador de
limpiarlos. Gas Propano/LP
Si la llama del piloto tiene la punta amarilla,
indica la presencia de polvo y suciedad en el
ensamble del piloto. Hay un pequeo orificio
de entrada de aire al piloto, aproximadamente
de 5 cm (2") de dimetro de donde sale la Orificio de
entrada de
llama del piloto (consulte la figura 38). Con la
aire al piloto Orificio de entrada
unidad apagada, haga pasar aire ligeramente
de aire al piloto
a travs del orificio de entrada de aire. Si no
Figura 38 - Orificio de entrada de aire al
cuenta con aire comprimido, puede soplar a
piloto
travs de una pajilla o popote.
GABINETE
Conductos de aire Exterior
Utilice una aspiradora o aire comprimido para Utilice un pao humedecido con una mez-
limpiarlos. cla de agua y jabn suave.
Frote el gabinete para quitar el polvo.
LEOS
Si retira los leos para limpiarlos, consulte Instalacin de los Leos, pgina 58, para ver
las instrucciones de colocacin.
Remplace el leo(s) si est roto o astillado (roturas de 1.7 cm o ms grandes).
68 www.usaprocom.com 200015-01B
SOLUCIN DE PROBLEMAS
200015-01B www.usaprocom.com 69
SOLUCIN DE PROBLEMAS
200015-01B www.usaprocom.com 71
SOLUCIN DE PROBLEMAS
72 www.usaprocom.com 200015-01B
PIEZAS DE REPUESTO
Nota: use slo piezas de repuesto originales. Esto proteger la cobertura de su garanta para
partes remplazadas bajo la garanta.
PIEZAS CON GARANTA
Comunquese con los distribuidores autoriza- su nombre,
dos de este producto. Si no pueden proporcio- su direccin
narle las piezas originales de repuesto, llame los nmeros de modelo y de serie de su
gratis al Departamento de Servicio al Cliente calentador,
al 1-866-573-0674 para obtener informacin
la falla del calentador,
de referencia.
El tipo de gas utilizado (propano/LP o gas
Cuando llame a Servicio al Cliente, tenga
natural/NG)
preparados:
la fecha de compra
Por lo general, le pediremos que devuelva la
pieza a la fbrica.
PIEZAS SIN GARANTA
Comunquese con los distribuidores autori- Cuando llame a Servicio al Cliente, tenga
zados de este producto. Si no pueden sumi- preparados:
nistrarle piezas de repuesto originales, llame los nmeros de modelo y de serie de su
gratis al Departamento de Servicio al Cliente calentador,
al 1-866-573-0674 para obtener informacin el nmero de la pieza de repuesto.
de referencia.
ACCESORIOS
Adquiera estos accesorios con su distribuidor local. Si no pueden proporcionarle estos ac-
cesorios, comunquese ProCom Heating, Inc. al 1-866-573-0674 para obtener informacin.
VLVULA DE INTERRUPCIN DE
EQUIPOS
Para todos los modelos. Vlvula de inte-
rrupcin de equipos con 1/8". Llave de paso
del TNP.
SERVICIO TCNICO
Es posible que tenga preguntas adicionales sobre la instalacin, el funcionamiento o la solucin
de problemas. De ser as, pngase en contacto con ProCom Heating, Inc. al 1-866-573-0674.
Al llamar tenga a la mano los nmeros de modelo y serie de su calentador.
200015-01B www.usaprocom.com 73
PIEZAS
MODELOS CRHEB24RT Y CRHEB30RT
13-2 13-3
13-1
13-7 13-4
13-6
13-5
Modelos 30" (76.2 cm)
(30" Models)
13-5
Modelos 24" (61 cm)
(24" Models)
13-9
13-10
13-8
Modelos
(30" 30"
Models)
(76.2 cm)
13-12
13-11
13-8 13-13
Modelos 24"Models)
(24" (61 cm)
11
3
4 TEMP
8
7
6 LE
AR
N
ON
RE
MO
TE
OF
F
10
5
2
9
1
12
74 www.usaprocom.com 200015-01B
PIEZAS
MODELOS CRHEB24RT Y CRHEB30RT
Esta lista contiene las piezas remplazables utilizadas en el calentador. Al hacer un pedido de
piezas, siga las instrucciones listadas en Piezas de repuesto en la pgina 73 de este manual.
Art- Pieza #
culo CRHEB24RT CRHEB30RT Descripcin Cant.
1 24ED102B-01 24ED102B-01 Rejilla de ensamble 1
2 PIMSC1-01 PIMSC1-01 Encendedor 1
3 RV83FI-4/9 RV83FI-4/9 Regulador de doble combustible 1
4 NDD0308-400 NDD0308-400 ODS/Piloto (doble combustible) 1
5 FBB28D11 FBB28D11 Ensamble del obturador de aire 1
Dispositivo de seleccin de com- 1
6 YDF06 YDF06
bustible
7 MDL304B MDL304B Perilla 1
Dispositivo de seleccin de com- 1
8 CRHEB24/30RT006 CRHEB24/30RT006
bustible soporte
9 MRT-01 MRT-01 Vlvula de control 1
10 RG04-1M RG04-1M Caja receptora 1
11 RG04-1T RG04-1T Control remoto 1
12 OD-C0889-11 OD-C0889-11 Solenoide 1
13 24ED117B-01 30ED105B-01 Juego completo de leos 1
13-1 CRHEB24/30RT301 CRHEB24/30RT301 Leo 1 1
13-2 CRHEB24/30RT302 CRHEB24/30RT302 Leo 2 1
13-3 CRHEB24/30RT303 CRHEB24/30RT303 Leo 3 1
13-4 CRHEB24/30RT304 CRHEB24/30RT304 Leo 4 1
13-5 CRHEB24RT305 CRHEB30RT305 Leo 5 1
13-6 CRHEB24/30RT306 CRHEB24/30RT306 Leo 6 1
13-7 CRHEB24/30RT307 CRHEB24/30RT307 Leo 7 1
13-8 CRHEB24RT308 CRHEB30RT308 Leo 8 1
13-9 CRHEB24/30RT309 CRHEB24/30RT309 Leo 9 1
13-10 CRHEB24/30RT310 CRHEB24/30RT310 Leo 10 1
13-11 CRHEB24/30RT311 CRHEB24/30RT311 Leo 11 1
13-12 CRHEB24/30RT312 CRHEB24/30RT312 Leo 12 1
13-13 CRHEB24/30RT313 CRHEB24/30RT313 Leo 13 1
PIEZAS DISPONIBLES - NO SE MUESTRAN
ML064-01 ML064-01 Paquete de hardware 1
HPL604-02 HPL604-02 Brasas 1
WZL039-01 WZL039-01 Rocas de lava 1
200015-01B www.usaprocom.com 75
GARANTA
GUARDE ESTA GARANTA
Modelo___________________________________