Escolar Documentos
Profissional Documentos
Cultura Documentos
DEPARTMENT OF
ELECTRONICS AND COMMUNICATION ENGINEERING
Prepared by Reviewed by
Approved by
HoD/ECE Principal
8086 signals Basic configurations System bus timing System design using 8086 IO
programming Introduction to Multiprogramming System Bus Structure Multiprocessor
configurations Coprocessor, Closely coupled and loosely Coupled configurations Introduction
to advanced processors.
UNIT IV MICROCONTROLLER 9
Architecture of 8051 Special Function Registers(SFRs) - I/O Pins Ports and Circuits -
Instruction set - Addressing modes - Assembly language programming.
Programming 8051 Timers - Serial Port Programming - Interrupts Programming LCD &
Keyboard Interfacing - ADC, DAC & Sensor Interfacing - External Memory Interface- Stepper
Motor and Waveform generation.
TOTAL: 45 PERIODS
6. The pin of minimum mode AD0- AD15 has _________ data bus
(a) 4 bit
(b) 20 bit
(c) 16 bit
(d) 32 bit
ANSWER: ( c)
8. In 8086 microprocessor the following has the highest priority among all type interrupts?
(a) NMI
(b) DIV 0
(c) TYPE 255
(d) OVER FLOW
ANSWER: ( a)
1. The main concerns of the ___________ are to define a flexible set of commands
(a) memory interface
(b) peripheral interface
(c) both ((a) and ((b)
(d) control interface
ANSWER: (a)
3. Port A acts as a 8-bit input data port to receive the digital data output from the ADC. The 8255 control
word for initialization is
(a) 68H
(b) 22H
(c) 80H
(d) 98H
ANSWER: ( d)
(a) 6V
(b) 10V
(c) 3.5V
(d) 22V
ANSWER: ( a)
5. In Traffic Light Controller, the operating frequency is assumed as 2 MHZ. calculate the time for one T-
state and the count of operation.
(a) 0.5 microseconds, 2B2 H
(b) 1.5 microseconds, 2C2 H
(c) 0.5 microseconds, 2C2 H
(d) 0.1 microseconds, 2E2 H
ANSWER: ( c)
6. In seven segment LED Display, to display a digit 6, the value in common cathode mode and anode mode
are
(a) 7DH, 82H
(b) 5GH, 67H
(c) 45H, 42H
(d) 7DH, 83H
ANSWER: ( a)
7. In 8086 based alarm system, the address location for Control register is
(a) 04H
(b) OCH
(c) OEH
(d) 0EH
ANSWER: ( d)
8. In DMA Controller, the status register is to keep track of DMA Channel pending request and status of
terminal counts. Choose the bits for Channel 1 to reach Terminal count.
(a) D7
(b) D1
(c) D2
(d) D5
ANSWER: ( b)
(a) 7
(b) 5
(c) 3
(d) 6
ANSWER: ( d)
10. In 8255 PIO Port, the function, data bus tristated is performed when
(a) CS(active low) =1
(b) CS(active low) =0
(c) CS(active low) =0, RD(active low) =1, WR(active low) =1
(d) CS(active low) =1 OR CS(active low) =0, RD(active low) =1, WR(active low) =1
UNIT IV-MICROCONTROLLER
2. What is the time taken by one machine cycle if crystal frequency is 20MHz?
(a) 1.085 micro seconds
(b) 0.60 micro seconds
(c) 0.75 micro seconds
(d) 1 micro seconds
ANSWER: ( b)
ANSWER: ( c)
8. When we add two numbers the destination address must always be.
(a) some immediate data
ANSWER: ( a)
UNIT V- INTERFACING MICROCONTROLLER
1. After RETI instruction is executed then the pointer will move to which location in the program?
(a) next interrupt of the interrupt vector table
(b) next instruction of the program after the IE instruction
(c) next instruction after the RETI in the memory
(d) none of the mentioned
ANSWER: ( b)
2. Which command of an LCD is used to shift the entire display to the right?
(a) 0x1C
(b) 0x18
(c) 0x05
(d) 0x07
ANSWER: ( a)
3. In stepper Motor Interfacing with 8051, the clockwise sequence of operation is,
(a) 1001, 1100, 0110, 0000
(b) 1001, 1111, 0110, 0010
(c) 1001, 1111, 0110, 1111
(d) 1001, 1100, 0110, 0011
ANSWER: ( d)
5. If we need to operate a key of a keyboard in an interrupt mode, then it will generate what kind of
interrupt?
(a) ES
(b) EX0/EX1
(c) T0/T1
(d) RESET
6. Which of the following steps detects the key in a 4*4 keyboard matrix about the key that is being
pressed?
(a) masking of bits
(b) ensuring that initially all keys are open
(c) checking that whether the key is actually pressed or not
(d) all of the mentioned
ANSWER: (d)
8. Which devices are specifically being used for converting serial to parallel and from parallel to serial
respectively?
(a) timers
(b) counters
(c) registers
(d) serial communication
ANSWER: (c)
9. Find out the roll over value for the timer in Mode 0, Mode 1 and Mode 2?
(a) 00FFH,0FFFH,FFFFH
(b) 1FFFH,0FFFH,FFFFH
(c) 1FFFH,FFFFH,00FFH
(d) 1FFFH,00FFH,FFFFH
ANSWER: ( c)