Escolar Documentos
Profissional Documentos
Cultura Documentos
ACCESO 20-10-15
CONTENIDO
CPE RC1201..................................................................................................................................................................2
1 ANTECEDENTES:...............................................................................................................................................2
PROCEDIMIENTO DE CONFIGURACIN..............................................................................................................2
1.1 Relacin de las interfaces.............................................................................................................................3
Pgina 1 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
CPE RC1201
1 ANTECEDENTES:
Vista FRONTAL
POSTERIOR
CPE RAISECOM MODELO: RC1201; Soporta los siguientes tipos de servicio ETH y TDM.
PROCEDIMIENTO DE CONFIGURACIN
El proceso de configuracin del ste CPE tiene por objetivo que el CPE pueda atender hasta tres
servicios a travs de sus 2 Interfaces ETH (Port 1, Port2) y una interface TDM con terminacin
75/120 como se muestra en la figura anterior.
Pgina 2 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
MODELO DE SERVICIO
Pgina 3 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
La configuracin del CPE para cualquier tipo de escenario de atencin de servicios, se ejecutar en dos ETAPAS:
Se configurar los parmetros de provisionados en la OIT relacionada a la gestin y monitoreo del equipo CPE.
Comunidad SNMP
public ro
private rw
Se ejecutar la configuracin de las interfaces Ethernet Puerto 1 y Puerto 2, que podrn atender cualquiera de los
siguientes servicios o la combinacin de ellos.
1.- NGN
2.- DBA
3.- DBI
4.- SIP-TRUNK
Se ejecutar la configuracin de la interface TDM Puerto 1, que podrn atender cualquiera de los siguientes
servicios
Pgina 4 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
DESARROLLO.
Para ambos mtodos de acceso se recomienda que el Aplicativo terminal, configurar el retardo de ingreso de los en
la lnea de comando para los caracteres de 0ms a 5ms, por ejemplo con el programa SecureCRT, esto con la
finalidad que cuando planchemos la configuracin la lnea de comandos no se equivoque y no se coma caracteres
y ejecute todos los comandos ingresados
Pgina 5 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
Pgina 6 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
1.- Configurar nuestra PC con la IP: 192.168.4.100 mascara 255.255.255.0, no configurar puerta enlace.
2.- Verificamos la conectividad desde nuestra LAPTOP al CPE y luego ingresamos al CPE por TELNET:
Pgina 7 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
C:\>ipconfig
Configuracin IP de Windows
C:\>ping 192.168.4.28
Pgina 8 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
Lograr la supervisin lgica del dispositivo como apoyo a su monitoreo y resolucin de averas; la gestin de este
equipo es INBAND, el equipo es gestionado a travs de la VLAN de gestin que llegar como al igual que otra
VLAN de servicios.
Provisionamiento de gestin del CPE: Considerar NODO Olgun; IP de gestin 10.121.1.3 /24 ruta por defecto
10.121.1.1; Vlan de gestin 50
Parmetros a configurar:
VALOR DE
INDEX VARIABLE PROVISIONAMIENTO
OBSERVACION
1 hostname OITS213333 numero de OIT
Pgina 9 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
OITS21333(config-vcc/1)# exit
OITS21333(config)#
OITS21333(config)# ip route 0.0.0.0 0.0.0.0 10.121.1.1
Successfully add a route
Pgina 10 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
Se tiene que configurar la negociacin entre el mdulo SFP y el SLOT del CPE.
Paso importante para establecer el enlace entre el CPE y el Puerto de servicio del ITN; se muestra un grfico
siguiente:
CPE ISCOM2110
USFP-03/SS135-D-R : ENLACE TSPF-03/SS153-D-R : Forzar a
CAP:1Gbps; Forzar
100Mbps OPTICO 100Mbps 100Mbps
100Mbps
CPE ISCOM2110 USFP-Gb/SS134-D-R: ENLACE TSFP-Gb/DS14-3: Forzar a
CAP:1Gbps 1Gbps OPTICO 1GBps 1Gbps
OITS21333#
Pgina 11 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
Pgina 12 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
2.- Configuramos LAS 4 VLANS DE LOS SERVICIOS: 1) GESTION 2) VOIP 3) DBI 4) TELEFONIA DIGITAL (PSEUDOWIRE)
OITS21333(config-eswif/0/3)#
OITS21333(config-eswif/0/3)# switchport trunk
Set Successfully.
OITS21333(config-eswif/0/3)# switchport trunk allowed vlan 50
Set Successfully.
OITS21333(config-eswif/0/3)#
OITS21333(config-eswif/0/3)# exit
OITS21333(config)# exit
OITS21333# ping 10.121.1.1
PING 10.121.1.3 (84=20+8+56 bytes)
64 bytes from 10.121.1.3: icmp_seq=0. time=0. ms
64 bytes from 10.121.1.3: icmp_seq=1. time=0. ms
64 bytes from 10.121.1.3: icmp_seq=2. time=0. ms
64 bytes from 10.121.1.3: icmp_seq=3. time=0. ms
----10.121.1.3 PING Statistics----
4 packets transmitted, 4 packets received, 0% packet loss
round-trip (ms) min/avg/max = 0/0/0
OITS21333#
HASTA AH TENEMOS CONFIGURADO Y VERIFICADO QUE EL CPE PUEDE SER ADMINISTRADO. GRABAMOS LA CONFIG
Y PROSEGUIMOS CON LA CONFIGURACIN DE LAS VLANS DE LOS SERVICIOS.
Pgina 13 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
bundle bundle logic port Inteface tipo tunnel donde se encapsulara el TDM over ETH
eth eth interface mode Interfaces Fsicas ETH
fx-ge fx-ge interface mode Slot ptico donde donde se inserta el SFP
sfp sfp interface mode Modulo ptico SFP
snmp Interface type Interface de gestin Outbnad
switchport ethernet switch port Interface Lgica del SWITCH
tdm tdm port Interface TDM E1 (75/120)
vcc Interface type Interface Lgica para Gestin INBAND
tdmop servicio para empaquetar el trfico TDM del CPE
B. Interface Tdmop
La interface TDMoP hace referencia a la interface lgica IP que se usa en el CPE RC1201 para paquetizar las
tramas TDM y para que luego sea enviado a por un TUNEL Ethernet desde y hacia el ITN.
Para verificar las propiedades del SERVICIO TDM OVER PACKET se ejecuta el siguiente procedimiento.
OITS21333#
OITS21333# conf t
Configuration mode, one command input per time. End with CTRL-Z.
OITS21333(config)# show tdmop info
Tdmop System IP Address: ...(1.1.1.1) Mac-address que se tiene
Tdmop System IP Address Mask: ...(255.0.0.0) informar al NOC cuando se
Tdmop System MAC Address: ...(00:0e:5e:3a:28:13) >>>>> configure servicios TDM Nativo
Current System Oscillator Type: ...(TCXO) a travs de la interface E1
Current System OOS code: ...(0x7e)
Current System OOS signaling: ...(0x05)
75/120.
Current System Source Clock Quality: ...(Stratum 3 / Type IV G.812)
TX HDLC Max Frame Size: ...(1468)
OITS21333(config)#
1.- Se configura la interface ptica (link ptico de planta externa entre el CPE y el ITN) si en la etapa de
configuracin de la gestin del equipo, ingresamos todas la vlans de los servicios, entonces no habr necesidad de
agregar configuracin adicional.
Pgina 14 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
2.- Se configura las Interfaces Elctricas donde va conectados los equipos de datos del cliente (router Cisco, Gaoke,
interfaces ETH PUERTO 1, ETH PUERTO 2)
OITS21333#
OITS21333# config terminal
OITS21333(config)# interface switchport 3
OITS21333(config-eswif/0/3)# switchport trunk
OITS21333(config-eswif/0/3)# switchport trunk allowed vlan 50,937,938
Verificamos
Configuramos la Velocidad:
Configuramos la interface ptica a 100Mbps; el slot elctrico es de 1GB; entonces estandarizamos la velocidad para
que levante el enlace con el ITN2100 con el lado NODO.
OITS21333(config-eswif/0/3)# exit
OITS21333(config)#
OITS21333(config)# interface fx-ge 1
OITS21333(config-fx-ge/0/1)# show this
current running configuration of this node:
interface fx-ge 1
als enable
flow-control on
speed 1000
OITS21333(config-fx-ge/0/1)# speed 100
Set successfully
OITS21333(config-fx-ge/0/1)# show this
current running configuration of this node:
interface fx-ge 1
als enable
flow-control on
speed 100
OITS21333(config-fx-ge/0/1)#
Pgina 15 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
OITS21333(config-eswif/0/1)# exit
OITS21333(config)# interface swit
OITS21333(config)# interface switchport 2
Pgina 16 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
OITS21333(config)# exit
OITS21333# exit
Login:
FIN DE CONFIGURACION
El presente procedimiento es vlido para la configuracin de servicio DBA (L2 o L3) Puerto Ethernet 1; y SIP-
TRUNK Puerto Ethernet 2; El procedimiento de configuracin se ejecutar siguiendo el siguiente orden.
1.- Se configura la interface ptica del CPE (link ptico de planta externa entre el CPE y el ITN) si en la etapa de
configuracin de la gestin del equipo, ingresamos todas la vlans de los servicios, entonces no habr necesidad de
agregar configuracin adicional en este punto.
2.- Se configura las Interfaces Elctricas donde va conectados los equipos de datos del cliente (router Cisco servicio
DBA ETH PUERTO 1; el Gateway DINSTAR interface ETH PUERTO 2)
Pgina 17 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
OITS21333#
OITS21333# config terminal
OITS21333(config)# interface switchport 3
OITS21333(config-eswif/0/3)# switchport trunk
OITS21333(config-eswif/0/3)# switchport trunk allowed vlan 50,939,940
Verificamos
Configuramos la Velocidad:
Configuramos la interface ptica a 100Mbps; el slot elctrico es de 1GB; entonces estandarizamos la velocidad para
que levante el enlace con el ITN2100 con el lado NODO.
OITS21333(config-eswif/0/3)# exit
OITS21333(config)#
OITS21333(config)# interface fx-ge 1
OITS21333(config-fx-ge/0/1)# show this
current running configuration of this node:
interface fx-ge 1
als enable
flow-control on
speed 1000
OITS21333(config-fx-ge/0/1)# speed 100
Set successfully
OITS21333(config-fx-ge/0/1)# show this
current running configuration of this node:
interface fx-ge 1
als enable
flow-control on
speed 100
OITS21333(config-fx-ge/0/1)#
Pgina 18 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
OITS21333(config-eswif/0/1)# exit
OITS21333(config)# interface swit
OITS21333(config)# interface switchport 2
Pgina 19 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
OITS21333(config)# exit
OITS21333# exit
Login:
FIN DE CONFIGURACION
Pgina 20 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
00-0e-5e-32:d5:66
interface bundle 1
payload-type satop
psn-type mef
raw-unframed-size 256
udp-dest-port-num 85e
tdm-port 1
dest-bundle 1
src-bundle-id-offset 0
dst-bundle-id-offset 0
jitter-buffer 8.00
inner-vlanid 3000
inner-vlan-priority 5
nexthop-address-type mac
mac-address-nexthop 00:0e:5e:32:d5:66
oam-connectivity disable
oos-act tx-oos
tag-vlan-mode tag
far-end-type e1t1
connect enable
S292289(config-tdm/0/1)# adaptive-bundleid 1
Set successfully
S292289(config-tdm/0/1)# tx
S292289(config-tdm/0/1)# tx-clock-src re
S292289(config-tdm/0/1)# tx-clock-src recovery
Set successfully
S292289(config-tdm/0/1)# exit
S292289(config)#
Pgina 21 de 22
SUB - GERENCIA DE REDES DE TRANSPORTE Y FECHA
ACCESO 20-10-15
00:0e:5e:32:e3:3b
Pgina 22 de 22