Escolar Documentos
Profissional Documentos
Cultura Documentos
com/articles/majgtkv5
3ders.org
Oct.24, 2013
EADS Innovation Works (IW), the aerospace and defence group's research
and technology organisation, is always on the look-out for new manufacturing
methods. A recent target for evaluation was an additive manufacturing
process called Direct Metal Laser-Sintering (DMLS).
As quality, costs and environmental effects play a major role in the decision-
making process for design and manufacturing solutions, EADS IW has defined
new Technology Readiness Level (TRL) criteria focusing on sustainability.
Nine TRL processes must be passed at EADS before a technology can be
qualified for use in production. For each TRL review, a technology's level of
maturity is evaluated in terms of performance, engineering, manufacturing,
operational readiness, value and risk. For each of these criteria, new
components must out-perform existing ones.
The results from the initial joint study of AM were evaluated in terms of CO2
emissions, energy and raw material efficiency and recycling. When analysing
energy consumption, the company's investigation included not only the
production phase, but also the sourcing and transportation of raw materials,
argon consumption for the atomisation of the DMLS metal powder, and
overall waste from atomisation.
1 of 5 10/01/2014 16.12
3D printing can cut material consumption by 75%, CO2 emissions by 4... https://www.readability.com/articles/majgtkv5
test results from EOS and, in an additional step, by test results from a raw
material (powder) supplier.
Conventionally designed and produced cast steel nacelle hinge bracket for an
Airbus A320. source: EADS
In the first instance, cast steel nacelle hinge brackets were compared to an
additively manufactured (AM) bracket of optimised titanium design by
measuring the energy consumption over the whole life cycle. The technology
turned out to be a good fit for the design optimisation, as for this application
the operational phase is typically 100 times more important than the static
phases (e.g. manufacturing the part).
2 of 5 10/01/2014 16.12
3D printing can cut material consumption by 75%, CO2 emissions by 4... https://www.readability.com/articles/majgtkv5
Optimised titanium version of the nacelle hinge bracket made by DMLS additive
manufacturing technology from EOS. source: EADS
3 of 5 10/01/2014 16.12
3D printing can cut material consumption by 75%, CO2 emissions by 4... https://www.readability.com/articles/majgtkv5
The study focused on the comparison between DMLS and rapid investment
casting of a single part and did not take into account the question of
scalability, which has yet to be addressed. However, some impressive results
were documented.
The optimised design of the nacelle hinge bracket allowed EADS and EOS to
demonstrate the potential to reduce the weight per aircraft by approximately
10 kg – a significant amount in aviation. CO2 emissions as a result of the
brackets were reduced by almost 40 per cent over their life cycle by
optimising the design, despite the fact that the EOS technology uses
significantly more energy during manufacture.
"In general, the joint study revealed that DMLS has the potential to build
light, sustainable parts with due regard to our company's CO2 footprint.
"A key driver of the study was the integrated and transparent cooperation
between customer and supplier, with an open approach that saw an
unprecedented level of information sharing.
"The collaboration has set the standard for future studies involving the
introduction and adoption of new technologies and processes.
"Even after the first positive results were evident, neither of the parties
settled for the outcome, but continued to investigate options for further
4 of 5 10/01/2014 16.12
3D printing can cut material consumption by 75%, CO2 emissions by 4... https://www.readability.com/articles/majgtkv5
improvement."
Part of the project's success was due to continued efforts towards further
enhancements, evidenced by the swapping of the EOSINT M 270 DMLS
machine for an EOSINT M 280 using titanium instead of steel, which led to
additional CO2 savings. The technology has the potential to make future
aircraft lighter, leading to savings in resources which help to meet
sustainability goals, without compromising on safety.
Jon Meyer, ALM Research Team Leader at EADS IW, added, "We see several
advantages in the use of DMLS, mainly concerning freedom of design and
ecological aspects.
Leave a comment:
Your Name:
Original URL:
http://www.3ders.org/articles/20131024-3d-printing-can-cut-material-consumption-
co2-emissions.html
5 of 5 10/01/2014 16.12