Escolar Documentos
Profissional Documentos
Cultura Documentos
DATA CONTENTS
MODIFICATION
#1 2002.3 Correction of exploded views. (P.4-2)
HISTORY #2 2002.9 Addition of Chinese model. (P.4-2, 4-3)
Addition of Block Diagram and Schematic diagrams/Printed Wiring Boards.
(P.3-1, 3-3~3-11)
MODEL NAME : SDM-S51 #3 2004.9 Addition of the LCD panels. (P.1)
SERVICE MANUAL Addition and change of 4-1. CHASSIS PART No. (P.4-2)
PARTS No. : 9-978-721-04
SPEC.
The SDM-S51 has two OLD PANEL NEW PANEL
varieties of the LCD panels. MODEL NAME COLOR DEST. SER. No. MODEL NAME COLOR DEST. SER. No.
Please make sure to determine SDM-S51/WQ UC Gray UC No. 4,000,001 ~ SDM-S51/WQ2 UC7 Gray UC No. 4,150.00 ~
SDM-S51/WQ1 UC Gray UC No. 4,047,389 ~
the service parts of the LCD SDM-S51/BQ UC Black UC No. 4,250,001 ~ SDM-S51/BQ2 UC7 Black UC No. 4,300,00 ~
module, I/F board and main SDM-S51/BQ1 UC Black UC No. 4,263,963 ~
harness assy. SDM-S51/WQ EK Gray AEP No. 4,500,001 ~ SDM-S51/WQ3 EKZ Gray AEP No. 4,650,00 ~
SDM-S51/WQ1 EK Gray AEP No. 4,535,257 ~
SDM-S51/WQ2 EK Gray AEP No. 4,545,849 ~
SDM-S51/BQ EK Black AEP No. 4,750,001 ~ SDM-S51/BQ2 EKZ Black AEP No. 4,800,00 ~
SDM-S51/BQ1 EK Black AEP No. 4,755,009 ~
SDM-S51/WQ AZ1 Gray SH No. 5,500,001 ~ SDM-S51/WQ1 AZ1 Gray SH No. 5,510,00 ~
SDM-S51/WQ CAN Gray CH No. 5,600,001 ~ SDM-S51/WQ1 CAN Gray CH No. 5,610,00 ~
SPECIFICATIONS
LCD panel Panel type: a-Si TFT Active Matrix Dimensions (width/height/depth)
Picture size: 15.0 inch Display (upright):
Input signal format RGB operating frequency* Approx. 387 × 330 × 175 mm
Horizontal: 28 - 60 kHz (15 1/4 × 13 × 7 inches)
Vertical: 48 - 75 Hz (with stand)
Resolution Horizontal: Max.1024 dots Approx. 387 × 281 × 48 mm
Vertical: Max.768 lines (15 1/4 × 11 1/8 × 1 15 /16 inches)
Input signal levels RGB video signal (without stand)
0.7 Vp-p, 75Ω , positive Mass Approx. 3.7 kg ( 8 lb 3 oz) (with
SYNC signal stand)
TTL level, 2.2 kΩ, Approx. 2.9 kg (6 lb 5 oz)
positive or negative (without stand)
(Separate horizontal and vertical, Plug & Play DDC2B
or composite sync) Accessories See page 7.
0.3 Vp-p, 75Ω, negative
(Sync on green) * Recommended horizontal and vertical timing condition
Power requirements 100 - 240 V, 50 - 60 Hz, Horizontal sync width duty should be more than 4.8% of total
Max. 0.56 A (U/C, AEP) horizontal time or 0.8 µs, whichever is larger.
Max. 0.8 A (CH) Horizontal blanking width should be more than 2.5 µsec.
DC input DC 12 V (supplied AC adapter) Vertical blanking width should be more than 450 µsec.
Power consumption Max. 25 W
Operating temperature 5 - 35 °C Design and specifications are subject to change without notice.
After correcting the original service problem, perform the following safety LEAKAGE TEST
checks before releasing the set to the customer: The AC leakage from any exposed metal part to earth ground and from all
1. Check the area of your repair for unsoldered or poorly-soldered exposed metal parts to any exposed metal part having a return to chassis,
connections. Check the entire board surface for solder splashes and must not exceed 0.5 mA (500 microamperes).
bridges. Leakage current can be measured by any one of three methods.
2. Check the interboard wiring to ensure that no wires are “pinched” or 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-
contact high-wattage resistors. 540A. Follow the manufacturers’ instructions to use these instruments.
3. Check that all control knobs, shields, covers, ground straps, and 2. A battery-operated AC milliammeter. The Data Precision 245 digital
mounting hardware have been replaced. Be absolutely certain that you multimeter is suitable for this job.
have replaced all the insulators. 3. Measuring the voltage drop across a resistor by means of a VOM or
4. Look for unauthorized replacement parts, particularly transistors, that battery-operated AC voltmeter. The “limit” indication is 0.75 V, so
were installed during a previous repair. Point them out to the customer analog meters must have an accurate low-voltage scale. The Simpson 250
and recommend their replacement. and Sanwa SH-63Trd are examples of a passive VOMs that are suitable.
5. Look for parts which, though functioning, show obvious signs of Nearly all battery operated digital multimeters that have a 2 V AC range
deterioration. Point them out to the customer and recommend their are suitable. (See Fig. A)
replacement.
6. Check the line cords for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.
7. Check the B+ and HV to see if they are specified values. Make sure your
instruments are accurate; be suspicious of your HV meter if sets always
To Exposed Metal
have low HV. Parts on Set
8. Check the antenna terminals, metal trim, “metallized” knobs, screws, and
all other exposed metal parts for AC Leakage. Check leakage as
described right.
AC
0.15 µF 1.5 kΩ Voltmeter
(0.75 V)
Earth Ground
SDM-S51(E) 2
WARNING!! AVERTISSEMENT!!
NEVER TURN ON THE POWER IN A CONDITION IN WHICH THE NE JAMAIS METTRE SOUS TENSION QUAND LA BOBINE DE
DEGAUSS COIL HAS BEEN REMOVED. DEMAGNETISATION EST ENLEVÉE.
SDM-S51(E) 3
POWER SAVING FUNCTION
This monitor meets the power-saving guidelines set by VESA,
ENERGY STAR, and NUTEK. If the monitor is connected to a
computer or video graphics board that is DPMS (Display Power
Management Signaling) compliant, the monitor will automatically
reduce power consumption as shown below.
SDM-S51
Power mode Power consumption 1 (power)
indicator
normal 25 W (max.) green
operation
active off* 3 W (max.) orange
(deep sleep)**
power off 3 W (max.) off
* When your computer enters the active off mode, the input signal is
cut and NO INPUT SIGNAL appears on the screen. After 20 seconds,
the monitor enters the power saving mode.
** deep sleep is the power saving mode defined by the Environmental
Protection Agency.
SDM-S51(E) 4
AUTOMATIC PICTURE QUALITY ADJUSTMENT FUNCTION
When the monitor receives an input signal, it automatically Consequently, the first time the monitor receives input signals
matches the signal to one of the factory preset modes stored in the that do not match one of the factory preset modes, the monitor
monitor,s memory to provide a high quality picture at the center may take a longer time than normal for displaying the picture on
of the screen. (See Appendix for a list of the factory preset the screen. This adjustment data is automatically stored in
modes.) memory so that next time, the monitor will function in the same
For input signals that do not match one of the factory preset way as when the monitor receives the signals that match one of
modes, the automatic picture quality adjustment function of this the factory preset modes.
monitor automatically adjusts the picture position, phase, and In all modes as above, if the picture is adjusted, the adjustment
pitch, and ensures that a clear picture appears on the screen for data is stored as a user mode and automatically recalled whenever
any timing within the monitor,s frequency range (horizontal: 28 - the same input signal is received.
60 kHz , vertical: 48 - 75 Hz ).
Note
While the automatic picture quality adjustment function is activated, only
the (power) switch will operate.
SDM-S51(E) 5
TABLE OF CONTENTS
2. ADJUSTMENTS
2-1. Functional Alignment (1) ..................................... 2-1
2-2. Functional Alignment (2) ..................................... 2-2
2-3. Table 1&2 ............................................................ 2-3
2-4. Timing Specification ............................................ 2-4
2-5. W/B Alignment Procedure .................................... 2-5
3. DIAGRAMS
3-1. Circuit Boards Location ........................................ 3-1
SDM-S51(E) 6
SECTION 1
DISASSEMBLY
1-1. BACK CABINET AND TFT PANEL REMOVAL
1 Four screws
(+PVTP 4x12)
2 Back cabinet
3 TFT panel
SDM-S51(E) 1-1
1-2. KEYBOARD MOUNT REMOVAL
1 Screw
(+PWH 3x4)
2 Four screws
(+PVTP 3x10)
3 Keyboard mount
SDM-S51(E) 1-2
1-3. INVERTER MOUNT REMOVAL
1 Two screws
(+PWH 3x4)
2 Inverter cover
3 Two screws
(+PWH 3x4) 4 Inverter shield
5 Inverter mount
6 CN2
6 CN1
6 CY2
SDM-S51(E) 1-3
1-4. I/F BOARD REMOVAL
1 Three screws
(+PWH 3x4)
2 I/F cover
3 Two screws
(+PWH 3x4)
3 Three screws 5 CN501
(+PWH 3x4)
5 CN201
5 CN302A
SDM-S51(E) 1-4
1-5. TFT PANEL REMOVAL
2 TFT panel
1 Four screws
(+PVTP 4x12)
SDM-S51(E) 1-5
SECTION 2
ADJUSTMENTS
2-1. FUNCTIONAL ALIGNMENT (1)
1. Hold “C” and “B” key power on, SDM-S51 goes into service mode.
2. Press “MENU” key-----ODS display → contigulation → RGB Reset → ΟΚ → contigulation → Color Temp.
3. Press “-” key to go to second page’s late icon.
4. Press “OK” key-----service menu display.
5. Select one of features.
6. Press “MENU” key to exit OSD.
7. Power OFF then ON again, monitor go to normal mode.
If you would like to enter service mode again, performing the above procedures cycle.
ANALOG 9300K
6500K
5000K
SUB-BRIGHTNESS
INITIAL EE PROM G
(N/A) CHIPS EXIT
CLEAR ETI TIME B
SYNC SLICE
1 RGB RESET SUB-CONTRAST
On
Off
Note
1. N/A means “Not applied”.
2. This service menu only provides both Configuration & Sync slice functions.
This other were used for design engineering. There is no guarantee of using those N/A functions.
SDM-S51(E) 2-1
2-2. FUNCTIONAL ALIGNMENT (2)
This paper documents the functional alignment (Used
• Operation d. Click ‘Refresh’.
Color meter) procedure of Sony LCD monitor
Refer to table 1 for default data for color
SDM-S51.
1. Execute software <ALIGN.EXE>. adjustment.
2. Click on ‘Setup’ menu. e. Adjust ‘sub_brt_B’ to achieve color temperature.
• Equipm ent
3. Select ‘Monitor’ type as ‘Sony SDM-S81 ’. Refer to table 2 for specification.
4. Select ‘COM PORT’ according to hardware connection. f. Click ‘Save this color’ for a 9300K color save.
Computer: PC workstation with Windows 95
5. Click <OK> to save the new setup configuration.
Installed PS/2 mouse is required
6. Quit this application and Re-enter to make the new 2. 5000K color adjustment
Software: KSi Engineering alignment software tool
settings effective. a. Click ‘Color Temperature’ as ‘5000’.
Color meter: Option
b. Repeat alignment procedure as 9300 steps b-f.
Signal generator: Option
• On Screen Adj ustment
Cable: Special RS232 interface cable
3. 6500K color adjustment
1. Click on the ‘Monitor’ icon; an virtual monitor panel a. Click ‘Color Temperature’ as ‘6500’.
• Setup
would show up. b. Repeat alignment procedure as 9300 steps b-f.
2. On entry, the software tries to establish a communication
1. Copy ECS software <ALIGN.EXE> into a new PC
link with the monitor. The monitor internal DACs • Geometry Adjus tment
directory.
are read and shown on screen sliders. A ‘CONNECT’
2. Prepare timing & pattern data for signal generator
icon would show up on the lower left corner of the 1. Connect the personal computer which has alignment
according to Sony’s timing specifications.
dialog screen. data.
3. Prepare timing files for <ALIGN.EXE>.
3. An error message would pop up should communication 2. Click ‘Refresh’ (inside Geometry Register Box).
4. Connect monitor interface cable between flat panel
fail. A ‘BREAK’ icon would show up on the dialog 3. Adjust ‘Pitch’ for optimum screen performance.
monitor and PC com port.
screen. If this happens, check the hardware setup, 4. Adjust ‘Phase’ for optimum screen performance.
5. Connect monitor video cable to signal generator.
communication cable, and the connection. 5. Adjust ‘H position’ to make the screen center
6. Put Topcon 50cm from the monitor; Point it
horizontally.
perpendicularly at the center of the display; Achieve
• Warm up time 6. Adjust ‘V position’ to make the screen center vertically.
the best focus through the eyepiece.
7. Repeat steps 3-6 for best picture performance.
7. Enclose the monitor and Topcon in a light-shield
8. Click ‘Save Geometry’ to perform a user timing mode
chamber. Allow 30 minutes warm up time before doing any adjust-
save.
8. Set up [SERVICE MODE] of the monitor. ment.
9. Repeat step 1-7 for each of the user present timings.
• Download • Color Adjustm ent
SDM-S51(E) 2-3
2-4. TIMING SPECIFICATION
PRESET MODE MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6 MODE 7 MODE 8
SIGNAL MODE VESA 60Hz MAC 13” VESA 75Hz VESA 85Hz VESA 70Hz VESA 60Hz VESA 75Hz VESA 85Hz
RESOLUTION 640 X 480 640 X 480 640 X 480 640 X 480 720 X 400 800 X 600 800 X 600 800 X 600
DOT CLOCK 25.175 MHz 30.240 MHz 31.500 MHz 36.000 MHz 28.350 MHz 40.000 MHz 49.500 MHz 56.250 MHz
H/V POLARITY N/N N/N N/N N/N N/P P/P P/P P/P
PRESET MODE MODE 9 MODE 10 MODE 11 MODE 12 MODE 13 MODE 14 MODE 15 MODE 16
SIGNAL MODE PMAC 16” VESA 60Hz VESA 70Hz VESA 75Hz VESA 75Hz PMAC 19” MAC WS
RESOLUTION 832 X 624 1024 X 768 1024 X 768 1024 X 768 1024 X 768 1024 X 768 1152 X 870 1152 X 900
DOT CLOCK 57.285 MHz 65.000 MHz 75.000 MHz 78.750 MHz 94.500 MHz 80.000 MHz 100.000 MHz 92.940 MHz
H/V POLARITY N/N N/N N/N P/P P/P N/N N/N N/N
SDM-S51(E) 2-4
PRESET MODE MODE 17 MODE 18 MODE 19 MODE 20 MODE 21 MODE 22
SIGNAL MODE WS VESA 60Hz VESA 85Hz VESA 60Hz VESA 75Hz VESA 85Hz
RESOLUTION 1152X 900 1280 X 960 1280 X 960 1280 X 1024 1280 X 1024 1280 X 1024
DOT CLOCK 105.590 MHz 108.000 MHz 148.500 MHz 108.000 MHz 135.000 MHz 157.500 MHz
SDM-S51(E) 2-5
2-5. W/B ALIGNMENT PROCEDURE
A. Measurement Condition:
- Measurement point: Center of screen
- Measurement distance: 50 cm
- Measurement Angle: 90Åã
B. Measurement equipment:
- Color Analyzer: Minolta CS-1000 or equivalent
- Signal Generator: VG-828D or equivalent
C. Alignment Procedure:
Alignment Procedure Parameter Setting & Specification
1. Aging: more than 30 minutes Burn-in mode: press "BRT"+"OK" then "Power ON"
2. Enter to "Service Mode" Service mode: press " "+" " then "Power ON"
3. RGB reset MaintainConfigurationRGB Reset
4. Initial Data Setting: S51: S81:
a. Brightness: 50 a. Brightness: 50
b. Contrast: 70 b. Contrast: 70
c. Sub-BRT (R/G/B): 128 c. Sub-BRT (R/G/B): 26
d. Sub-CONT (R/G/B): 50 d. Sub-CONT (R/G/B): 128
5. Input gray raster pattern 35 IRE (1024*768, 60K/75Hz) 30 IRE (1280*1024, 80K/75Hz)
6. Adjust White Balance (9300K, 6500K & 5000K) and Luminance
(10 nits @ SONY CS-1000) by Sub-BRT 9300K 6500K 5000K Tolerance
x 0.2838 0.3132 0.3450 }0.003
Remark: In normally, adjust G for Luminance (Y), adjust R for x and adjust
B for y. y 0.2981 0.3297 0.3580 }0.003
Y 10 10 10 }0.7
7. All mode recall Select OSD All mode recall:
"ALL press"CONTRA
RESET" ST"+"OK" then
function "Power ON"
SDM-S51(E) 2-6
SECTION 3
DIAGRAMS
#2 3-1. BLOCK DIAGRAM
ON/OFF INVERTER
IC304
24LC21
CN303 DDC IC401
ANALOG GRAPHICS T0911
SIGNAL I/P
SCALER
IC601 ZURAC2 15"LCD TFT
AD9883A
ADC
IC301
T8570D
OSD
IC302
W78E62B
MCU
IC303
CN304 24C16
EEPROM
RS-232
KEY-MATRIX
CN202
DC JACK
INTERFACE BOARD (MCU, OSD, POWER SW, INPUT TERMINAL) H BOARD (KER BOARD)
H (Keyboard) mount
I/F mount
Inverter mount
each having the code INTERFACE-a to INTERFACE-e. For example, the destination Emitter
qh Transistor Collector
ab1 on the code INTERFACE-a sheet is connected to ab1 on the INTERFACE-b sheet. Base
a b 1 – Discrete semiconductot
Ver.1.6
Ref. No. (Chip semiconductors that are not actually used are included.)
1 2 3 4 5 6 7 8 9
CN302B
1
2
TO 3
B INTERFACE (C) BOARD
CN302A
4
5 D908
6 5V1
7 D907
8 D906 5V1
9 D902
5V1 5V1
10 D905
11 D904 5V1
CON11 D903 5V1
5V1
C
1
D901
3
S905 S907 S906 S902 S903 S901
D UP OK DOWN MENU CONTRAST POWER
S904
H BOARD
BRIGHT (KEY)
B-SS3615<J..> - H..
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
PRA 0~7 a d 15
PGA 0~7 a d 16
+3.3V
+2V5 +3V3 +2V5 +3V3 PBA 0~7 a d 17
PGA7
PGA6
PGA5
PRA7
PRA6
PRA5
PRA4
PRA3
PRA2
PRA1
PRA0
C405 C406
+2.5V 100n 100n
+2V5
B RP401 C401
100X4
ab1 PCRA 0~7 100n
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
PCRA7 8 7 IRA7
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
PCRA6 6 5 IRA6
C407
GND
IABLU2
IABLU3
IABLU4
IABLU5
IABLU6
IABLU7
VDD3
IAGRN0
IAGRN1
IAGRN2
IAGRN3
GND
IAGRN4
IAGRN5
IAGRN6
IAGRN7
IARED0
IARED1
IARED2
VDD2
IARED3
IARED4
IARED5
IARED6
IARED7
GND
PARED7
PARED6
PARED5
PARED4
PARED3
PARED2
VDD3
PARED1
PARED0
PAGRN7
PAGRN6
PAGRN5
GND
PCRA5 4 3 IRA5
PCRA4 2 1 IRA4 +2.5V +3.3V 100n
PCRA3 8 7 IRA3 GND GND 80
PCRA2 6 5 IRA2 R419 IABLU1 PAGRN4 79 PGA4
PCRA1 4 3 IRA1 47R IABLU0 PAGRN3 78 PGA3
PCRA0 2 1 IRA0 ab4 CKADCA IACLK PAGRN2 77 PGA2
76 PGA1
C RP402
100X4
C325
33P
IBCLK(YUVLLC)
GND
PAGRN1
PAGRN0 75
74
PGA0
abc5 COAST COAST VDD2
73 PBA7
VDD2 PABLU7
72 PBA6
ab6 RGHS R418
RGHS PABLU6
71 PBA5
47R
GND PABLU5
70 PBA4
PHSYNC a d 18
RP403
abe7 SVSYNC IAVSYNC PABLU4
69 PBA3
R404
IAHS IAHSYNC PABLU3 0
100X4 R416 IRA7 68 PBA2 a c19
ab2 PCGA 0~7 PCGA7 8 7 IGA7 ab8 IRA6
IBRED7(YIN7/YUV7) PABLU2
67 PBA1
LMCOUNT
47R IBRED6(YIN6/YUV6) PABLU1
PCGA6 6 5 IGA6 IRA5 IBRED5(YIN5/YUV5) 66 PBA0 R408
PABLU0 +3V3
PCGA5 4 3 IGA5 IRA4 GND 65 #
IBRED4(YIN4/YUV4)
D PCGA4
PCGA3
2
8
1
7
IGA4
IGA3
IRA3
IRA2 IBRED3(YIN3/YUV3)
IBRED2(YIN2/YUV2) IC401
PHSYNC
VDD3
64
63
+3.3V
R409
PCGA2 6 5 IGA2 IRA1 PQFP160 PDE 62
PCGA1 4 3 IGA1 IBRED1(YIN1/YUV1) 47
IRA0 IBRED0(YIN0/YUV0) Zurac2/3t0911 PVSYNC 61 PCLK a d 22
PCGA0 2 1 IGA0 VDD2 PQFP160 VDD2 60
IGA7 59 +2V5 C415
IGA6 IBGRN7(YUVPLLC2) SCALER PBRED7 C410 C411 C421
RP404 PBRED6 58 15p
100X4 IGA5 IBGRN6(YUVVS) 57 100n 100n #
IBGRN5(YUVHS) PBRED5 C412 0603
IGA4 PBRED4 56
IGA3 IBGRN4 100n
IBGRN3 GND 55
IGA2 54 PBCLK FB401
IBGRN2(YUVVREF) PACLK
IGA1 53 +2.5V BRED / 120u
E RP405
IGA0
IBGRN1(YUVHREF)
IBGRN0(YUVCREF)
VDDPP/PBCLK
VDDAP 52
51
+2V5
CLAMP VSSAP
100X4 IBA7 50
ab3 PCBA 0~7
PCBA7 8 7 IBA7 IBA6
IBGRN7(YUVPLLC2) XSSPP
49 C413 C414
;y
IBGRN6(YUVVS) XO
PCBA6 6 5 IBA6 IBA5 X1 48 R410 100n 47u / 6.3V
PCBA5 4 3 IBA5 IBA4 IBGRN5(YUVHS) 47
IBGRN4 VDD3 1M CHIP
PCBA4 2 1 IBA4 PBRED3 46
PCBA3 8 7 IBA3 VDD3 45
IBA3 IBBLU3(UVIN3) PBRED2
PCBA2 6 5 IBA2 IBA2 IBBLU2(UVIN2) 44
PBRED1 43
PCBA1 4 3 IBA1 IBA1 PBRED0
IBBLU1(UVIN1) 42
PCBA0 2 1 IBA0 IBA0 IBBLU0(UVIN0) PBGRN7
F RP406
GND GND 41 X401
14.318MHz
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
100X4
C408 C409
C402 C403 C404 33p 33p
100n 100n 100n
abe9 SHSYNC
R415 PDE a d 20
a c 10 TTic-INTn 47R
a c 11 TTfc-RSTn C416 C417 C418 PVSYNC a d 21
100n 100n 100n +3.3V
+3V3
SDA R401 100
G a b c 12 3.4 SDA
3.4SCL
SCL R402 100
+3V3 D201 +2V5
a c 13 SIB
ASICPDP
R417 47 +2V5 +3.3V +2.5V
a c 14 CSIN +2.5V
R403 C419
# 100n C201 +
100n C202
100u/6.3V
R302 ZPWN a c 23
H 100
1 VSS VSS 16
2 R303 22R
XIN R 15
3 NC G 14 R304 22R
4 VDD IC301 B 13 R305 22R
R301 C301 OVHS 5 T8570D 12 R306 22R
* R220 6 HS FB 11
1k 100R SSB OSD INT 10
0603 7
SDA VS
8 9
SCLK VDD
R219
I 100R R219
100R
+5V INTERFACE-a
VCC
(SCALER, OSD)
B-SS3615<J..> - INTERFACE-P1
IC2
TOREX/XC62FP3302PR/SOT89 3.3VCC3
FB601 VPLL
B +5V
3.3V REG
+3.3V BEAD/120U +3.3V
2 3
VCC VI VO VOP
FB602 VD FB603
+
C203 BEAD/120U +3.3V +3.3V BEAD/120U
GND
100n C215 +3V3
1 100U/6.3V
+3.3V
+ C616
C627 C626 C628 C629 C620 C622 C623 C611 C612 100UF
+ C613 C614 C615 C677 C618 C619
C 100n 100n 100n 100n 100n 100n 100n 100n 100n
100n 100n 100n 100n 100n 100n
6.3V
CHIP
C624
100UF
26
27
39
42
45
46
51
52
59
62
34
35
11
22
23
69
78
79
6.3V
CHIP
VD
VD
VD
VD
VD
VD
VD
VD
VD
VD
PVD
PVD
VDD
VDD
VDD
VDD
VDD
VDD
C605
47n 54 70 PCRA7
D RIN
C606
RAIN R7
R6 71 PCRA6
PCRA 0-7 ab1
72 PCRA5
47n 48 R5 73 PCRA4
GIN GAIN R4
R601 R3 74 PCRA3
be24 C607 75 PCRA2
* R2
47n 43 76 PCRA1
abe9 SHSYNC BIN BAIN R1
77 PCRA0
r607 c608 R0
ab6 RGHS 220 1n 49 2 PCGA7
R601 R603 VGAG SOGIN G7 3 PCGA6
22 * G6
4 PCGA5
PCGA 0-7 ab2
E C601 38
CLAMP
G5
G4
5 PCGA4
* 6 PCGA3
IC601 G3
R604 30 7 PCGA2
HSYNC SLAVE ADDRESS : 98 G2
22 G1 8 PCGA1
abe7 SVSYNC AD9883KST-110 GO 9 PCGA0
31 LQFP80
abc5 COAST VSYNC 13 PCBA7
R605 29 B7 13 PCBA6
# R606 COAST A/D CONVERTER B6 PCBA 0-7 ab3
B5 14 PCBA5
C602 2.2 r608 15 PCBA4
0 58 B4 16 PCBA3
22p
F V REFADC
37
REF B3
B2 17 PCBA2
B1 18 PCBA1
C630 MIDSCV 19 PCBA0
+3.3V 33 B0
3.9n FILT ab4
VPLL R609 FILT
DATACLK 67 CKADCA
100 57 66
C604 abc12 SDA
56 SDA HSOUT
64
IAHS ab8
C603 + 39n SCL SCL VSOUT
55 65
100u R610 AO SOGOUT CSIN ab9
6.3V R611 100
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
3.3 C609 C610
G 100n 100n
10
20
21
24
25
28
32
36
40
41
44
47
50
53
60
61
63
68
80
1
INTERFACE-b
(A/D CONVERTER)
I
B-SS3615<J..> - INTERFACE-P2
A VCC IC302
+5V W78E62B/PLCC44
MCU VCC
X301 44 1 12
12mHz 35 EA/VP 43
P0.0
P0.1 42
IC305 21 41
R309 X1 P0.2
MCP810 P0.3 40
C303 1M RESET 39
P0.4 R311 R310 R312
20 38
B 100n R307
4.7
C304 C305 C306100n
X2 P0.5
P0.6 37 4.7 4.7 4.7
P-12V
22p 22p P0.7 36
3 2 10 FB201
RESET
24 PANEL PWR BEAD/120U/1206
1 P2.0
25 BACKLITn
PANEL PWR ce27
ac10 14
P2.1
26 R360
TTfc-INTn P3.2/INT0 P2.2
abc5 COAST 15 P2.3 27 100 FB202
16 P3.3/INT1 28
SHSYNC-UC P3.4/T0 P2.4 VGA-DET ce28 BEAD/120U/1206 +12V
ce25 VOL-ADJ 17 P2.5 29
P3.5/T1 VCC
P2.6 30 LED 2
2 31
ac19 LMCOUNT P1.0/T2 P2.7 +5V
C R320
100
3
4 T1.1/T2EX 19 VOL-MUTE
C205 +
CN201
SCL P1.2 P3.7/RD 470U 16V
abc12 SDA 5
P1.3 P3.6/WR 18 ASICPDP ac13 1
R321 6 PSEN 32 R206 2
7 P1.4
P1.5 ALE/P 33 3 TO
100 8 13 R314 100 10K
P1.6 P3.1/TXD R204 Q201 4 INVERTER
P4.0
P4.1
VSS
9 11 I ON/OFF
ac11 TTfc-RSTn P1.7 P3.0/WR 4.7 BC848 5 BOARD
R315 100 SOT-23 6
22 23 24 C206
R207 7
R348 R349 10UF 25V
82K CHIP
100 100 R205
D ce26 DDC SDA 4.7
VCC
BC848 CN302A
G SOT-23
R334 220 1
2
R333 220 3 TO
R340 4.7K R325 470 4
R339 4.7K R324 470 H BOARD
5 CN302B
R338 4.7K R323 470 6
R337 4.7K R322 470 7
R346 4.7K R344 470 8
R347 4.7K R343470 9
R342 4.7K R345 470 10
H
C310 C316
* *
CN304 5 2 1 3
HEADER4-100mil
FOR RS232C 8 7 4 6 C311 C313 C314 C315
MINI DIN
* C312 * * *
*
I INTERFACE-C
(MCU, EEPROM)
B-SS3615<J..> - INTERFACE-P3
C503 C507
15p 15p
C505 CN501
C504 C506 C508
15p CLKJIA
15p 15p 15p 1 2
3 4 H-SYNC
VSYNC
5 6
C RA2
7
9
8
10 RA3
RA4 11 12
RA5 13 14 RA6
RA7 15 16
17 18
GA2 19 20 GA3
GA4 21 22
GA5 23 24 GA6
ad16 PGA 0-7 GA7 25 26
27 28
FB511 120U GA2 BA2 BA3
D PGA2
PGA3 FB512 120U GA3 BA4
29
31
30
32
PGA4 FB513 120U GA4 BA5 33 34 BA6
PGA5 FB514 120U GA5 BA7 35 36
PGA6 FB515 120U GA6 PODE 37 38
PGA7 FB516 120U GA7 39 40 Vpn 16
41
C511 C513 C517
15p 15p 15p TO
LCD
C514 C516 C518 TFT
E 15p 15p 15p
HEADR-20X2
C530
0.1U
25V
P-CLK
DE-UN
0 0
ad21 PVSYNC
R502
0 C525 C526 C527 C528
ad18 PHSYNC 15p # # #
R503
0
H ad20 PDE
R504
0
ad22 PCLK
INTERFACE-d
(MCU, EEPROM)
I
B-SS3615<J..> - INTERFACE-P4
IC202
S18050SD/LM25965S/DIP5
A POWER SW
P-12V
CN202 4
DC+12V FEEDBACK VCC
F201 +12V L201 D301
1 1 100UH
3 VIN BAS16
CHOKE
2 250VAC EOR13X8X6LC SOT-23
+5V VCC
T5AH 2 1 2
ON/OFF
OUTPUT
GND
C208
B 100n C210
R630 R629
C631
C209 100n 14
5
D202 Å{ Å{ 2.2K 2.2K IC602D
C207 470U R632 100n
1 8 R327
SS36/DO-201 16V C216 NC VCC 100
470UF 2 7 100 VSYNC-A 9 8 11 10
10V SMD 470U 3
NC VCLK
6
SVSYNC abc7
16V 4
NC SCL
5
DDCSCL ce29 IC602E
GND SDA DDCSDA ce26 7
SMD R328 74HC14D
C308
IC304 100n D604 100
ST24LC21BM6TR/S08 BAS16
C EEPROM SOT-23
R631
IC602B
100
3 4 5 6
SHSYNC abc9
IC203 IC602C
VCC +3V3 C632
1RU1050CP/TO252
*
LDO
3 2 R626
+5V VIN VOUT +3.3V 22
1 2
R209 SHSYNC-U04 ce25
D + C211 ADJ 200F D607
IC602A
47UF/16V 1206 BAS16LT1
74HCT14D
CHIP SOT-23 +5V +5V
1
+ C212
VCC
220UF/10V C639
100n R628 R627
2
R210
332F R625 4.7 4.7
2
1206 4.7
D612 3 3 3
3
BAV99
E SOT-23 D606 D605
D603
1
D601
1
1
5.6V 5.6V BAV99
SOT-23 SOT-23 D602 BAV99
SOT-23
1
BAV99 SOT-23
FB604 SOT-23
BEAD/120
INTERFACE-e
(POWER SW, LDO)
SDM-S51(E) 4-1
REF.NO. PART NO. DESCRIPTION REMARK
4-1. CHASSIS
1 4-087-927-01 BEZEL ASSY(WHITE)(U/C, AEP, CH)
PWH3 x 4
4-087-930-01 BEZEL ASSY(BLACK)(U/C, AEP)
3 PWH
3x4 #1 #3 2 1-804-691-11 LCD PANEL(LPL OLD F3)
PWH3 x 4
1-805-236-11 LCD PANEL(LPL NEW A3)
2 #2 #3 3 1-761-556-12 I/F BOARD MOUNT(LPL OLD F3)
PWH
3x4
1-761-556-21 I/F BOARD MOUNT(LPL NEW A3)
PWH
3x6 4 1-761-554-11 KEYBOARD MOUNT
PWH
PVTP 3x4
3 x 10
5 1-761-549-11 INVERTER MOUNT
5 6 4-087-928-01 STAND ASSY(WHITE)(U/C, AEP, CH)
4 4-087-931-01 STAND ASSY(BLACK)(U/C, AEP)
7 4-087-919-01 COVER, REAR(WHITE)(U/C, AEP, CH)
B2.6 x 5
4-087-920-01 COVER, REAR(BLACK)(U/C, AEP)
PVTP4 x 12
6 PSW4 x 10
8 4-087-926-01 CABINET ASSY(WHITE)(U/C, AEP, CH)
7 4-087-929-01 CABINET ASSY(BLACK)(U/C, AEP)
1
#2 9 4-087-354-01 LABEL, INFORMATION(WHITE)
(U/C,AEP)
4-087-354-04 LABEL, INFORMATION(WHITE)(CH)
4-087-354-21 LABEL, INFORMATION(BLACK)
8
(U/C, AEP)
K3 x 8
PTP3 x 8 P4 x 10
SDM-S51(E) 4-2
REF.NO. PART NO. DESCRIPTION REMARK
4-2. PACKING MATERIALS
51 4-087-213-01 INDIVIDUAL CARTON
52 4-087-768-01 CUSHION (LEFT)
53 4-087-767-01 CUSHION (RIGHT)
54 4-087-766-01 CUSHION (BOTTOM)
55 1-477-228-11 ADPTOR, AC(WHITE)
55 56 57 58 59 1-477-231-11 ADPTOR, AC(BLACK)
52
56 1-765-719-11 CORD SET, POWER(BLACK)(AEP)
1-765-719-21 CORD SET, POWER(WHITE)(AEP)
1-765-720-11 CORD SET, POWER(BLACK)(U/C)
53
1-765-720-21 CORD SET, POWER(WHITE)(U/C)
57 1-757-371-11 CABLE ASSY(HD15X2)(WHITE)
1-757-371-21 CABLE ASSY(HD15X2)(BLACK)
51
SDM-S51(E) 4-3
SECTION 5
ELECTRICAL PARTS LIST
NOTE: • Items marked " * " are not stocked since
they are seldom required for routine
The components identified ! marked are service. Some delay should be anticipated
critical for safety. when ordering these items.
Replace only with the part number specified.
RESISTORS
• All resistors are in ohms
Les composants identifiés par la marque !
• F : nonflammable
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
SDM-S51(E) 5-1
*:INVERTER BOARD **:I/F MOUNT
No. # Board Type ! /* Ref.No. Part No. Descrption Remarks-1 Remarks-2 Difference
1 A* FUSE F201 1-576-633-11
2 B** IC IC302 6-801-646-01 W78E62B-40
SDM-S51(E) 5-2
English
2004IL08-Data
Sony EMCS Corporation
Made in Japan
9-978-721-04 Ichinomiya Tec 2004. 9
SDM-S51(E) 22