Escolar Documentos
Profissional Documentos
Cultura Documentos
®
PRO/II 9.2
Silent Install Guide
March 2013
All rights reserved. No part of this documentation shall be reproduced, stored in a retrieval system, or
transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without the
prior written permission of Invensys Systems, Inc. No copyright or patent liability is assumed with
respect to the use of the information contained herein. Although every precaution has been taken in the
preparation of this documentation, the publisher and the author assume no responsibility for errors or
omissions. Neither is any liability assumed for damages resulting from the use of the information
contained herein.
The information in this documentation is subject to change without notice and does not represent a
commitment on the part of Invensys Systems, Inc. The software described in this documentation is
furnished under a license or nondisclosure agreement. This software may be used or copied only in
accordance with the terms of these agreements.
For comments or suggestions about the product documentation, send an e-mail message to
ProductDocumentationComments@invensys.com.
All terms mentioned in this documentation that are known to be trademarks or service marks have been
appropriately capitalized. Invensys Systems, Inc. cannot attest to the accuracy of this information. Use of
a term in this documentation should not be regarded as affecting the validity of any trademark or service
mark. Invensys, Invensys logo, PRO/II, and SimSci-Esscor are trademarks of Invensys plc, its
subsidiaries and affiliates.
PRO/II-9.2 Silent Installation Guide
The PRO/II 9.2 silent install does not install its dependencies. Therefore, you have to make sure that these
dependencies are installed before doing the silent install of PRO/II 9.2. Below are the commands to silently
install the PRO/II 9.2dependencies and PRO/II 9.2. Note that the [PRO/II 9.2 setup folder] below is where
the PRO/II 9.2install setup.exe is and the whole path has to be surrounded by double quotes if it contains a
space.
7. Install USB driver 7.6.5 (Conditional). Note that this is needed only if you are going to run PRO/II 9.2
using USB for security.
"[PRO/II 9.2 setup folder]\ThirdPartySoftware\USB_Driver\Sentinel Protection Installer 7.6.5.exe" /qn
9. Notepad++ (Mandatory)
[PRO/II 9.2 setup folder]\ThirdPartySoftware \NOTEPAD\\npp.6.3.Installer.exe /s
4. QUICK_LAUNCH_ICON – option to create a quick launch icon (default: not create). To create the icon,
use QUICK_LAUNCH_ICON=1
5. DESKTOP_ICON – option to create a desktop icon (default: create). To not create the icon, use
DESKTOP_ICON=””
6. ADDLOCAL – to specify what PRO/II 9.2features to install. If this option is not used in the PRO/II
9.2silent install, the program will install ProgramFiles, UserFiles, UAS, PDTS, and PFE_Editor.
Features that can be specified include UAS, PDTS, PFE_Editor, Translator, Notepadplus,
NIST_REFPROP (must specify COMPANY_NAME as well).
Note that unless ADDLOCAL=ALL is used, features ProgramFiles and UserFiles must always be
included in the list when using the ADDLOCAL option.
Examples: To install all features, use ADDLOCAL=ALL. To also install UAS and PDTS, use
ADDLOCAL=ProgramFiles,UserFiles,UAS,PDTS, Notepadplus, NIST_REFPROP
Command example:
msiexec.exe /i [PRO/II 9.2setup folder]\PROII.msi /qn SECURITY_TYPE=TOKEN
INSTALLDIR="c:\program files\simsci" DESKTOP_ICON="" QUICK_LAUNCH_ICON=1
IPASSI_LICENSE_FILE=@TokenServer
ADDLOCAL=ProgramFiles,UserFiles,UAS,PDTS,Translator, Notepadplus,
NIST_REFPROP,S4MPortal
The command above uses TOKEN for security, installs PRO/II 9.2to c:\program files\simsci, does not
create the desktop icon, creates the quick launch icon, and uses machine TokenServer for the TOKEN
security. It also installs UAS, PDTS, and Translator.