Escolar Documentos
Profissional Documentos
Cultura Documentos
IV. UNITS
I. INTRODUCTION
Use either SI (MKS) or CGS as primary units. (SI units
Highlight a section that you want to designate with a
are strongly encouraged.) English units may be used as
certain style, then select the appropriate name on the style
secondary units (in parentheses). This applies to papers in
menu. The style will adjust your fonts and line spacing. Do
data storage. For example, write “15 Gb/cm 2 (100
not change the font sizes or line spacing to squeeze more
Gb/in 2).” An exception is when English units are used as
text into a limited number of pages. Use italics for
identifiers in trade, such as “3½ in disk drive.” Avoid
emphasis; do not underline.
combining SI and CGS units, such as current in amperes
To insert images in Word, position the cursor at the
and magnetic field in oersteds. This often leads to confusion
insertion point and either use Insert | Picture | From File or
because equations do not balance dimensionally. If you
copy the image to the Windows clipboard and then Edit |
must use mixed units, clearly state the units for each
Paste Special | Picture (with “Float over text” unchecked).
quantity in an equation.
INTERNATIONAL JOURNAL OF CHEMICAL
The SI unit for magnetic field strength H is A/m.
ENGINEERING AND APPLICATIONS reserves the right
However, if you wish to use units of T, either refer to
to do the final formatting of your paper.
magnetic flux density B or magnetic field strength
symbolized as µ0H. Use the center dot to separate
compound units, e.g., “A·m 2.”
II.PROCEDURE FOR PAPER SUBMISSION
A. Review Stage
V. HELPFUL HINTS
Submit your manuscript electronically for review.
B. Final Stage A. Figures and Tables
When you submit your final version, after your paper has Because the final formatting of your paper is limited in
been accepted, prepare it in two-column format, including scale, you need to position figures and tables at the top and
figures and tables. bottom of each column. Large figures and tables may span
both columns. Place figure captions below the figures; place
C. Figures table titles above the tables. If your figure has two parts,
As said, to insert images in Word, position the cursor at include the labels “(a)” and “(b)” as part of the artwork.
the insertion point and either use Insert | Picture | From File Please verify that the figures and tables you mention in the
or copy the image to the Windows clipboard and then Edit | text actually exist. Do not put borders around the outside
of your figures. Use the abbreviation “Fig.” even at the
Manuscript received October 9, 2001. (Write the date on which you beginning of a sentence. Do not abbreviate “Table.” Tables
submitted your paper for review.) This work was supported in part by the U.S. are numbered with Roman numerals.
Department of Commerce under Grant BS123456 (sponsor and financial Include a note with your final paper indicating that you
support acknowledgment goes here). Paper titles should be written in
uppercase and lowercase letters, not all uppercase. Avoid writing long request color printing. Do not use color unless it is
formulas with subscripts in the title; short formulas that identify the elements necessary for the proper interpretation of your figures.
are fine (e.g., "Nd–Fe–B"). Do not write "(Invited)" in the title. Full names of
authors are preferred in the author field, but are not required. Put a space
Figure axis labels are often a source of confusion. Use
between authors' initials. words rather than symbols. As an example, write the
F. A. Author is with the National Institute of Standards and Technology, quantity “Magnetization,” or “Magnetization M,” not just
Boulder, CO 80305 USA (e-mail: author@ boulder.nist.gov).
S. B. Author was with Rice University, Houston, TX 77005 USA. He is
“M.” Put units in parentheses. Do not label axes only with
now with the Department of Physics, Colorado State University, Fort Collins, units. As in Fig. 1, for example, write “Magnetization
CO 80523 USA (e-mail: author@lamar. colostate.edu).
T. C. Author is with the Electrical Engineering Department, University of
(A/m)” or “Magnetization (A m1),” not just “A/m.” Do
Colorado, Boulder, CO 80309 USA, on leave from the National Research not label axes with a ratio of quantities and units. For
Institute for Metals, Tsukuba, Japan (e-mail: author@nrim.go.jp).
example, write “Temperature (K),” not “Temperature/K.” unavoidable (for example, “INTERNATIONAL JOURNAL
Multipliers can be especially confusing. Write OF CHEMICAL ENGINEERING AND APPLICATIONS”
“Magnetization (kA/m)” or “Magnetization (10 3 A/m).” Do in the title of this article).
not write “Magnetization (A/m) 1000” because the reader D. Equations
would not know whether the top axis label in Fig. 1 meant
16000 A/m or 0.016 A/m. Figure labels should be legible, Number equations consecutively with equation numbers
approximately 8 to 12 point type. in parentheses flush with the right margin, as in (1). First
use the equation editor to create the equation. Then select
TABLE I: THE ARRANGEMENT OF CHANNELS the “Equation” markup style. Press the tab key and write
Channels Group 1 Group 2 … Group c the equation number in parentheses. To make your
Main channel Channel 1 Channel 2 … Channel c equations more compact, you may use the solidus ( / ), the
Assistant channel Channel 2 Channel 3 … Channel 1 exp function, or appropriate exponents. Use parentheses to
avoid ambiguities in denominators. Punctuate equations
when they are part of a sentence, as in
r2
0
F ( r , ) dr d [ r2 / ( 2 0 )]
exp( | z j zi | ) 1 J 1 ( r2 ) J 0 ( ri ) d .
0
(1)