Escolar Documentos
Profissional Documentos
Cultura Documentos
£
avoids time-consuming welding or removing the need for hot work permits
REASONS TO USE...
®
+44 (0) 1274 521444 www.Lindapter.com © Lindapter International 2017
Girder Clamps by Lindapter ® | 5
Typical Configurations
The Girder Clamp represents a range of Lindapter products that are compatible with virtually any
shape or size of steel section and can withstand loading conditions in a wide variety of applications,
for example:
GIRDER CLAMPS
The original configuration is designed to secure steel sections and resist
STANDARD
RAIL FIXINGS
See the components of a Girder Clamp in more detail on page 6.
LIFTING POINTS
HIGH SLIP RESISTANCE
HOLLO-BOLT
and provide a fastening position for the Lindapter clamps.
FLOOR FIXINGS
Inclined beam-to-beam (combined loading)
ADJUSTABLE
More examples of typical Lindapter configurations can be found on pages 26 - 29. Alternatively, visit the website.
®
© Lindapter International 2017 www.Lindapter.com +44 (0) 1274 521444
6 | Girder Clamps by Lindapter ®
Standard Hardened
Washer (200 Hv).
RAIL FIXINGS
16mm
FOR THE LOAD APPLIED AND THE CLAMPING FORCE
Height of nut
Flange Thickness = 15.5mm GENERATED FROM THE TIGHTENING OF THE FASTENERS.
4. WHERE NECESSARY WORKMANSHIP FOR ITEMS SHOWN
ON THIS DRAWING SHOULD COMPLY WITH THE RELEVANT
SECTIONS OF THE NATIONAL STRUCTURAL STEELWORK
SPECIFICATION (NSSS) FOR BUILDING CONSTRUCTION 5TH
EDITION CE MARKING VERSION.
5. IF FELT NECESSARY, WHERE EXCESSIVE VIBRATION MAY BE
A CONCERN, IT IS ACCEPTABLE FOR CERTAIN TYPES OF
ANTI-VIBRATION LOCKING DEVICES SUCH AS, BUT NOT
A LIMITED TO, PROPRIETARY WASHERS AND NUTS TO BE
USED WITH LINDAPTER COMPONENTS AND/OR
ASSEMBLIES; SPRING WASHERS OF ANY TYPE ARE NOT
RECOMMENDED. IN THESE SITUATIONS IT IS IMPORTANT
THAT THE MANUFACTURER'S INSTALLATION INSTRUCTIONS
ARE FOLLOWED. NO GUARANTEES OR WARRANTIES ARE
IMPLIED.
10
DRAWING NOTES:
1. DIMENSIONS ARE IN MM
Lower Beam 2. TOLERANCES:
Flange Width = 102mm 3.
4.
ANGULAR: BEND
MATERIAL COATINGS TO BE SPECIFIED BY THE ENGINEER
3mm
Flange Thickness = 6mm
5:1
Lindapter B12L Clamp
T
Lindapter Fastener 69 Nm
Tightening Torque =
Lindapter P1S12 Packer For combined loadings the current relevant national
standard should be taken into consideration
PROJECT
270 DETAIL A
SCALE 1 : 1.5 DRAWING TITLE
218 GC001-1
116
www.lindapter.com
CUSTOMER ENQUIRY N.
®
+44 (0) 1274 521444 www.Lindapter.com © Lindapter International 2017
Girder Clamps by Lindapter ® | 7
Product Comparison
The table below shows the various components that can be assembled in a Girder Clamp arrangement.
Each product has specific properties, for example the Type AF heavy duty clamp can resist tensile loads
up to 250kN when used with four bolts (property class 10.9) in a Girder Clamp assembly.
Single Components
GIRDER CLAMPS
Product Parallel Tapered Tensile High Slip Low Temp. Slotted Adjustable Stainless
Flanges Flanges Resistance Down to -60oC Clearance Holes Steel
Type A
page 8 - - - - - -
Type B
page 9 - - - - - -
RAIL FIXINGS
Type AAF
page 12 -
Type AF
page 14 - - -
Type CF
LIFTING POINTS
page 15 - - -
Type LR
page 18 - - -
Type D2
page 19 - - - - -
HOLLO-BOLT
Type LS
page 22 - -
Type RC
page 24 - - - - -
FLOOR FIXINGS
Other Clamp Systems (these products do not require a location plate)
Product Parallel Tapered Tensile High Slip Low Temp. Slotted Adjustable Stainless
Flanges Flanges Resistance Down to -60oC Clearance Holes Steel
Type F9
page 24 - - - - -
SUPPORT FIXINGS
Type FC
page 25 - - - -
Also available
DECKING FIXINGS
®
© Lindapter International 2017 www.Lindapter.com +44 (0) 1274 521444