SOMIA
FABRICATIONS
eurotrip fender installation
Euro™p
For 37mm, 45mm and 6omm wide
model
1. Side the break away brackets onto fenders to the
Approximate locations Srown on crawing, they were not
pre-installed
2, Ther are two V-shaped stays per fender. Position the
‘Ystay so the serowneds atthe bese fave out (nat towares
{he whoo's hus). nor the ends of te V-shazod stays
ito the brackets unt hey sap in. After double checking
that the brackets on both sides are evenly positaned on
the fonder in the location shown on drawing, gory 1ock
‘down the serewe tothe fendors Do not verghteh
4. Attach the fran fender t the fork using ru ang 47mm
Bal Place bol throug te halen fork crown, thon trough
holdin bulls tab of top of front fender. Tighton foes rut
while keeping fender centered
Break Away Bracket
Seana
Suny ce
eee eer
cory erie
SOnrIA
FABRICATIONS
eurotrip fender installation
4, Bott the V-stays to tho outsdo ofthe thread dropout eyolots|
ling the 14mm bolts and washers. Laosering tho Pailips hea
crow at tho base of to “V" allows adjustment or tr clearance
‘Mako sure fender isnot touching tho re, Ratighton tho screws on
Both sdos aftr adjusting.
CAUTION: Mako sure
fonder or hardware dos
Pot intorore with moving
parts on the Beye
§. Attach the front ond of rear fonder tothe chanstay bridge using
the presi metal cp, Tipton lock ut whl Kaping london
Centred, Double chock tha breakaway brackets arvin the correct
Focation, Reads: needed,
6, Bort the V-stays tothe outsdo ofthe threaded dropout eyolets
Using the T4mnr bolts and washorslugo low" ayolet sot thre aro
two sets), Loosoning the Philips head scrow atthe base of tho *V"
‘lowe adjustment fort charbnco, Make sua onder isnot touching
the tre, Roighton the serewe on both Ss ator adlustng
For 37mm, 45mm and 6omm wide
Eurotrip models:
1. Slide the break away brackets onto fenders to the
Approximate locatons shown on craving, they were not
resnetalles
2, Thar are two V-shaped stays per fender. Postion the
‘stay so the serewhead atte bie face out (nt foward
{he wheats Fub)- Inger the ence of the V-shaped stays
intone brackets untl they snap in. ter double checking
that the brackets on bot sides are evenly postoned on
the ‘ender nthe location shown on drawing, genty ke
‘down the screws to the fenders, Do ot overtighten
2. Attach the front fender to the fr using nut and Aen
Bolt. Pace bot trough the Rain fork ero, then though
Fld in builtin tab on top of front fender Tighten Tock nut
ve keeping ender centerea
‘oc he at
ada
4, Bolt the V-stays tothe outside ofthe thread dropout eyelets
ting the 4mm oalts and washers. Loosening the Philips head
‘scrow at the base of to "V" allows adjustment orto clearance.
Make sure fender isnot touching the tra. Retighton the sera on
both des aftr adjusting,
not interfere wits moving
parison the Bicycle,
5. Attach the frontend of rer fender to the chainstay bridge using
tha proinstaled metal clip Tighten ock rut while Keoping Tendo
Senterod, Double chock that breakaway brackets aren the correct
Tocation. Readjust f needed.
6. Bol the V-stays tothe outside of the threaded dropout eyelets
ting the 4mm nalts and washersluse lower ayolet sot i tre are
two Sets, Loosaning the Philips nea scrext at the base of tho "V
Sowe adjustment ote clearance. Make ura ‘endr'snot touching
‘Rotghten the screws on bath sides alter adjusting
Loosen Philips
Serew to adjust
Tength