Escolar Documentos
Profissional Documentos
Cultura Documentos
Cable length limitations (Based on published Bus and Serial Communications Standards)
Apply good industry practices for long cable runs - keep cable away from high power AC lines and all motor drive cables.
R-Series sensor models Baud rate Maximum cable or bus length G-Series sensor models Maximum cable length
1.5 MBd 10 ft. (3 m) G-Series Analog (Voltage or Current) 150 ft. (45 m) -
R-Series SSI
400 kBd 160 ft. (50 m)
G-Series digital (PWM or Start/Stop) 300 ft. (90 m) Note 1
300 kBd 320 ft. (100 m)
200 kBd 650 ft. (200 m) G-Series Neuter
100 kBd 1300 ft. (400 m) 250 ft. (75 m) Note 2
(Start/Stop output wired for square wave neuter)
Accessories
1.0 MBd 80 ft. (25 m)
500 kBd 320 ft. (100 m)
R-Series CANbus
250 kBd 820 ft. (250 m)
Notes:
125 kBd 1640 ft. (500 m) 1. 300 feet maximum using the ± differential pair for the interrogation
(Start) and gate (Stop) signals.
500 kBd 420 ft. (130 m)
2. 250 feet maximum using single-ended interrogation (Start) signal.
R-Series DeviceNet 250 kBd 800 ft. (270 m)
The unused interrogation signal MUST be terminated to ground at the
125 kBd 1730 ft. (530 m)
control box.
12 MBd 330 ft. (100 m)
1.5 MBd 650 ft. (200 m)
R-Series Profibus 500 kBd 1300 ft. (400 m)
187.5 kBd 3280 ft. (1000 m)
≤93.75 kBd 3940 ft. (1200 m)
Standard 6-pin connector type (D60) used with R-Series G-Series and E-Series Sensors
D
1 2 3 4 5 6 7 8
025 = 25 ft.
050 = 50 ft.
100 = 100 ft.
_ _ _ = Cable length (ft)*
D
1 2 3 4 5 6 7 8
DF = Female connector, (straight exit), and #530040 cable for Profibus sensors with D63 connector
DG = Female connector, (90° exit), and #530040 cable for Profibus sensors with D63 connector
Type DG
CABLE LENGTHS* (3-5)
* Refer to “Cable Length Limitations” table on page 75 for maximum cable length.
Standard 7-pin DIN connector type (D70) used with R-Series SSI Sensors
D P O
1 2 3 4 5 6 7
D7 = Female connector, (straight exit), and #530029 cable (high performance shielding, orange polyurethane jacket), for SSI sensors with D70 connector.
DR = Female connector, (90° exit), and #530029 cable (high performance shielding, orange polyurethane jacket), for SSI sensors with D70 connector.
DS = Female connector, (straight exit) and standard #530026 cable, (PVC jacket), for SSI sensors with D70 connector.
DT = Female connector, (90° exit), and standard #530026 cable, (PVC jacket), for SSI sensors with D70 connector.
DU = Female connector, (straight exit), and #530045 cable, (black polyurethane jacket), for SSI sensors with D70 connector.
DV = Female connector, (90° exit), and #530045 cable, (black polyurethane jacket), for SSI sensors with D70 connector.
Accessories
For standard length cables up to 100 ft.
005 = 5 ft.
015 = 15 ft.
025 = 25 ft.
050 = 50 ft.
100 = 100 ft.
_ _ _ = Cable length (ft)*
* Maximum cable length is dependent on the baud rate (refer to “Cable Length Limitations” table on page 75)
10-pin MS connector type (MS0) used with R-Series SSI and G-Series Sensors
M F P O
1 2 3 4 5 6 7
MF = Female connector, (straight exit), and #530045 cable (black polyurethane jacket) for R-Series and G-Series sensors with MS0 connector.
* Maximum cable length is dependent on the baud rate (refer to “Cable Length Limitations” table on page 75)
Used when replacing Tempo II and model LH sensors that have integral RB connectors
-2 1 ft. cable length, standard For G-Series digital-pulse and neuter output sensors
-2 5 ft. cable length For G-Series digital-pulse and neuter output sensors
Accessories
-2 1 ft. cable length, standard for G-Series digital-pulse and neuter output sensors.
Used when replacing model LH sensors that have integral or in-line 10-pin MS connectors
-2 1 ft. cable length, standard For G-Series digital-pulse and neuter output sensors.
-2 5 ft. cable length For G-Series digital-pulse and neuter output sensors
Used when replacing Tempo II and model LH sensors that have in-line MS connectors wired for the R1, R2, or R3 connection types
Used when replacing models LH, LP and R-Series sensors that have integral RG connectors
Part no: 253248, -1, -2
For R-Series analog or G-Series analog and digital-pulse output
Female straight exit D6 to -1 1 ft. cable length, standard
sensors
male RG connection adapter
cables
For R-Series analog or G-Series analog and digital-pulse output
-2 5 ft. cable length
sensors
Accessories
Used when replacing model LP sensors that have the integral C-style connector or in-line H or J style connectors
Part no. 370423 Housing: Zinc nickel Female, for Profibus sensors
Accessories
Part no. 560778 Housing: Zinc nickel Female, 90° exit, mates to
54 mm
D6 Field- plated D60 & Profibus D63
(2.13 in.)
installable Termination: Solder connection type on R-Series,
connector Contact insert: Silver G-Series & E-Series sensors
38 mm plated with six conductor cable
(1.5 in.) Cable clamp: PG9, (STC09131-6)
M16
Ø 19.5 mm Max. cable dia.: 8 mm
(0.77 in.)
Part no. 370460 54 mm Housing: Zinc nickel Male, 90° exit, for Profibus
Profibus D6 Field- (2.13 in.) plated sensors (D63 connection
installable connector Termination: Solder type) (STC09131-6P)
Contact insert: Silver
38 mm
plated
(1.5 in.)
Cable clamp: PG9
Ø 19.5 mm
Max. cable dia.: 8mm
(0.77 in.)
Part no. 252347* 48 mm Housing: Zinc nickel For use with Model RH, RP &
Profibus bus (1.9 in.) plated RF sensors, Male connector
terminator Termination: Solder type
18 mm Contact insert: Silver
* was 370419 plated
(0.7 in.)
(STA09131H06)
dia.
7-pin style connectors
Part no. 560701 Housing: Zinc nickel Female, Straight exit, mates
54 mm
D7 Field-installable connector plated to D70 connection type on
(2.13 in.)
Termination: Solder R-Series sensors. Connector
Contact insert: Silver has PG7 size strain relief for
Ø 18 mm plated standard cable.
(0.71 in.) Cable clamp: PG7 (STC09131D07)
Part no. 560779 54 mm Housing: Zinc nickel Female, 90° exit, mates to D70
D7 Field-installable (2.13 in.) plated connection type on
connector Termination: Solder R-Series sensors
Contact insert: Silver (STC09131-7)
38 mm plated
Cable clamp: PG9, M16
(1.5 in.)
Max. cable dia.: 8 mm
Ø 19.5 mm
(0.77 in.)
M 12
2 3
Accessories
Part no. 530064 Cable jacket: 2 male M12 connectors
5 meter industrial Ethernet Polyurethane (D-coded) for EtherCAT
cable (Cat 5e Es) with sensor (D56 connection
47 mm
2 4-pin M12 connectors Cable type)
(1.85 in.)
M12x1
RJ45
4-pin M12 Cable
connector
41 mm
(1.6 in.)
3 mm
19 mm (1.15 in.)
(0.74 in.) dia.
Part no. 560885 Housing: Zinc nickel Female, straight exit, for
M12 Field-installable connector plated Profibus sensors (D53 con-
20 mm Termination: Solder nection type)
(0.77 in.) dia. Contacts: Silver
Accessories
57 mm plated
(2.24 in.)
Part no. 560884 Housing: Zinc nickel Male, straight exit, for
M12 Field-installable connector plated Profibus sensors (D53 con-
20 mm Termination: Solder nection type)
(0.77 in.) dia. Contacts: Silver
62 mm plated
(2.44 in.)
Part no. 560888 Housing: Zinc nickel Male, for Profibus sensors
43 mm
M12 Profibus bus terminator plated (D53 connection type)
(1.69 in.)
22 mm Contacts: Silver
(0.87 in) plated
16 mm 14 mm
(0.64 in.) (0.55 in.)
dia.
Part no. 370515 Housing: Zinc nickel Male, 90° exit, for Profibus
M12 Field-installable connector 54 mm plated sensors (D53 connection
(1.12 in.)
Termination: Solder type)
40 mm Contacts: Silver
(1.57 in.) plated
Part no. 370514 Housing: Zinc nickel Female, 90° exit, for Profibus
54 mm
M12 Field-installable connector plated sensors (D53 connection
(2.12 in.)
Termination: Solder type)
38 mm Contacts: Silver
(1.50 in.) plated
Part no. 560886 Housing: Zinc nickel Female, 90° exit, for input
M8 (4-pin) Field-installable connector 28 mm plated voltage for Profibus sensors
(1.1 in.) Termination: Solder (D53 connection type)
Contacts: Silver
12 mm plated
(0.47 in.) 12.5 mm
dia. (0.49 in.)
Part no. 370504 Housing: Zinc nickel Female, straight exit, for
M8 (4-pin) Field-installable connector 40 mm plated 24Vdc input power for
(1.58 in.) Termination: Solder Profibus sensors (D53 con-
12 mm Contacts: Silver nection type)
(0.58 in.) dia.
plated
27 mm
(1.1 in.)
Accessories
Part no. 401366 Female, straight exit
RG Field-installable connector 58 mm mates to RG connection type
on R-Series and L-Series
(2.28 in.)
19 mm
(0.75 in.)
Part no. 370391 Housing: Zinc nickel Female, straight exit, mates to
D8 Field-installable connector 54 mm plated D80 connection type on
(2.13 in.) Termination: Solder Model L Series
Contact insert: Silver
Ø 18 mm plated
(0.71 in.) Cable clamp: PG7
Thickness:9.5mm(0.375in.)
Part no. 252183 GFK, magnet hard For Model RP, GP, EP
24 mm 43 mm
Captive-sliding (0.94 in.) (1.69 in.) ferrite Similar to (252182) but with
magnet 20 mm Weight: Approx. 30g extra length on the
(0.79 in.) Operating temperature: ball-jointed arm
Rotation:
Vertical: 18° -40 to 75° C
Horizontal: 360°
24 mm
Ball-jointed arm, (0.95 in.)
M5 thread
40 mm
(1.58 in.)
31 mm
4.3 mm 13.5 mm
(1.22 in.)
(0.17 in.) dia. (0.53 in.)
Accessories
Part no. 400533 Composite: PA-Ferrite For Model RH, GH
Small ring magnet Weight: Approx. 10g
Operating temperature:
-40 to +100° C
24 mm
A (0.95 in.)
A I.D. 33 mm
(1.3 in.)
Compatibility Chart
Sensor Model
Magnet
Part no. Rod-style Profile-style
RH GH RP GP EP
201542-2 • •
201553 • •
201554 • •
201298-2 • • • • •
251416-2 • • • • •
Accessories
251447 (float) • •
252182 • • •
252183 • • •
252184 • • •
400533 • •
401032 • •
401467 • •
401468 • •
HOW TO ORDER
Pressure Housing (for use with Temposonics sensor models GH and RH only)
H H
1 2 3 4 5 6 7 8
Part no. 252004 9 mm Stainless steel with For use with Model RP, GP,
Mounting feet, 5 mm (0.196 in.) I.D. (0.36 in.) nylon washer's and and EP sensors. Provides
28 mm
insulated (1.1 in.) cloth tape on bottom electrical and mechanical
2 mm 9 mm
(0.08 in.) (0.36 in.) isolation.
50 mm (1.97 in.)
68 mm
(2.68 in)
Width = 14.5 mm (0.57 in.)
Accessories
Part no. 401602 M5 thread Nut for mounting RP and GP
Base channel T-slot nut sensors.
5 mm (0.20 in.)
T-Slot nut, M5 thread
(optional, sold separately)
MECHANICAL END CONNECTORS (FOR USE WITH TEMPOSONICS SENSOR MODELS RP, GP, EP AND ER)
M5 inside
thread
Rotation: 18˚
allowable
Mounting Hardware:
1/4 in. Hex nuts (2 pcs.)
14 mm (0.56 in.) O.D. washer
Part no. 253347 See Part no. 561255 Male M6 rod ends (2pieces), plus special wrench for use
Rod end kit (Metric) with Model ER sensors.
Accessories
Part no. 560444 Male 1/4-28 for use with Model ER sensors.
Rod end attachment (English) 7 mm
(0.28 in.) 16 ° Misalign
Angle
9.5 mm
(0.37 in.)
1/4-28
6 mm
(0.24 in.)
25 mm
(1 in.)
19 mm
(0.74 in.)
40 mm
(1.57 in.)
6 mm
(0.24 in.)
22 mm
(0.87 in.)
19 mm
(0.75 in.)
36 mm
(1.42 in.)
OPTIONAL EXTENSION RODS (FOR USE WITH TEMPOSONICS SENSOR MODELS RP, GP, AND EP WITH CAPTIVE-SLIDING MAGNET ONLY)
Extension rod lengths Part no. Extension rod lengths Part no. Extension rod lengths Part no.
60.3 mm (2.375 in.) 401768-2 238.1 mm (9.375 in.) 401768-9 517.5 mm (20.375 in.) 401768-20
85.7 mm (3.375 in.) 401768-3 263.5 mm (10.375 in.) 401768-10 542.9 mm (21.375 in.) 401768-21
111.1 mm (4.375 in.) 401768-4 314.3 mm (12.375 in.) 401768-12 619.1 mm (24.375 in.) 401768-24
161.9 mm (6.375 in.) 401768-6 365.1 mm (14.375 in.) 401768-14 771.5 mm (30.375 in.) 401768-30
187.3 mm (7.375 in.) 401768-7 390.5 mm (15.375 in.) 401768-15 923.9 mm (36.375 in.) 401768-36
212.7 mm (8.375 in.) 401768-8 466.7 mm (18.375 in.) 401768-18 1076.3 mm (42.375 in.) 401768-42
1228.7 mm (48.375 in.) 401768-48
1533.5 mm (60.375 in.) 401768-60
Extension rod
Part no. 401768-XX
9.5 mm
15.2 mm (0.375 in.)
(0.60 in.)
(both ends) M5-0.8 thread bore
(both ends)
Part no. 500018 M18 x 1.5 threads Stainless steel M18 x 1.5 nut for use with
Hex jam-nut models RH and GH sensors
with style “M” housing.
10 mm
(0.4 in.) ID
Part no. 560777 27 mm 10 mm 304 stainless steel For use with GH and RH
(1.06 in.) OD 5 (0.4
mm in.) ID
Accessories
Collar 27 mm (0.2 in.) pressure housings and float
(1.06 in.) OD 5 mm 251447.
(0.2 in.)
8-32 threads
9 mm 4 mm
8-32 threads (0.16 in.)
(0.34 in.) 4
9 mm 8 mm
mm
(0.34 in.) (0.16
(0.31 in.)
in.)
8 mm
Part no. 560315 (0.31 in.) Fluoroelastomer 75 ± Spare, for use with rod-style
O-Ring, for US 16 mm ± 0.23 mm 2 mm ± 0.08 mm 5 durometer sensor Models RH and GH.
customary flange (0.644 in. ± 0.009 in.) I.D. (0.087 in. ± 0.003 in.) With style “T” or “S”
with 3/4-16 UNF threads housing.
24 Vdc
Part no. 251153 109.5 mm Meter for use with Start/Stop sensors
Temposonics Display Unit 7 mm (4.31 in.) only.
(0.275 in.)
(TDU-200)*
48 mm SIDE 45 mm FRONT 48 mm
(1.89 in.) (1.78 in.) (1.89 in.)
96 mm
(3.78 in.)
91 mm
(3.6 in.)
Note: BACK 45 mm
(1.78 in.)
*Product Specification 550178 and User’s Manual 550260.
POWER SUPPLY
Part no: 380009 100 mm x 165 mm x 50 mm. Standard power supply (110 Vac to 24
Sensor power supply Vdc/ 0.5 A) for use with sensors and
interface products.
SENSOR PROGRAMMING
Product Application
Part no. 253124 For adjusting null (setpoint 1) and span (setpoint 2) on R-Series analog
R-Series analog hand-held programmer sensors, (for single magnet versions only).
Sensor 24 V
Part no. 253408 For adjusting null (setpoint 1) and span (setpoint 2) on R-Series analog
R-Series analog cabinet programmer sensors, (for single magnet versions only). The programmer is designed for
snap-in mounting on standard 35 mm DIN rail. A “program/run” switch
allows the programmer to be permanately wired inside the control cabinet.
Part no. 253309 Interface converter box, power supply, PC software and cabling.
R-Series analog PC programming kit
Part no. 253310 Interface converter box, power supply, PC software and cabling.
R-Series SSI PC programming kit
Part no. 252173-D63 For field address programming of R-Series Profibus output.
R-Series Profibus node address
programmer
Part no. 252382-D62 For field address programming of R-Series CANopen sensors.
R-Series CANbus programming accessories
Product Application
Part no. 253294 For adjusting null (setpoint 1) and span (setpoint 2) on G-Series analog
G-Series analog hand-held programmer sensors.
Part no. 380078 For adjusting null (setpoint 1) and span (setpoint 2) on G-Series analog
G-Series infrared setpoint programmer sensors.
Accessories
Part no. 253311 Interface converter box, power supply, PC software and cabling.
G-Series analog PC programming kit
Part no. 253312 Interface converter box, power supply, PC software and cabling.
G-Series digital pulse PC programming kit
Part no. 401727 Can be used to check the sensors functions and to change the slave
Profibus master simulator address. Allows the magnet positions and diagnostic data to be read.
Product Application
Part no. 551033 Includes G-Series PC setup software (part no: 625060)* G-Series Palm OS
G-Series documentation and software CD software (part no: 625061)*, G-Series User’s Manual (part no: 550966)
Download software from www.mtssensors.com and additional documentation.
Part no. 551052 Includes R-Series PC setup software (part no: 625064)*, parameter files
R-Series documentation and software CD and product documentation.
Download software from www.mtssensors.com
Note:
* Download software from our website (www.mtssensors.com)