Escolar Documentos
Profissional Documentos
Cultura Documentos
Size
Width: from 3000 to 8000 mm
Height: from 2500 mm to 5000 mm
Door leaf width:
1100 mm up to 5000 mm max. height
1200 mm up to 4500 mm max. height
1300 mm up to 4000 mm max. height
Max. number of leaves: 7
Version
Hörmann aluminium extrusion system (without thermal insulation).
Frame material group 3. Wall thickness of the extrusions: 2 mm.
Overall thickness: 60 mm.
System construction
Connection
Mitres: pressed glued joints using solid corner angles and PU adhesive.
Butt joints: screw connection via screw channels or butt connectors.
Sealant systems
Glazing system
Dry glazing: on the outside a pre-laid tape, whose lip seal works with the internal glazing wedge to maintain
the seal of the glass rebate despite variations in wind pressure. Pre-laid tape sealed into the corners. There
are openings in the rebate floor to relieve steam pressure or to drain off condensation water. Combination
possibilities between different glazing bars and seals to accept glass thicknesses of 4-40 mm.
Closing edge protection:
In general, large section continuous EPDM hollow chamber profile.
Approximate values Thermal insulation value k approx. 5,2 W/m2 K
Acoustic rating approx. 20 dB (A)
Surface finishes
Standard:
E6/EV1 = stained/natural shade
E1/CH5 = ground/bronze shade
Powder-coated to RAL colour chart (Standard: RAL 9016 bright white)
Special: Coating in RAL colours.
Folding arrangements
- see page 10/11
Opening angle
90°, 180°
Locking leaf
LH hinged, RH hinged
Type of fitting
- external (opening outwards)
- internal (opening inwards)
- between walls (opening inwards or outwards)
- in the reveal (opening inwards or outwards)
Frame
3-sided frame extrusion,
Z-shaped steel threshold profile
Rail width
92.5 mm, 110 mm, 150 mm, 230 mm
Rail location
horizontal, vertical combination of rail widths
Fittings
Door leaf from 3001 mm with 3 two-part zinc die-cast hinges, screwed to both the inside and outside of the
door, with plastic bushes and lubricator nipples. Traffic leaf with bolt lock to accept profile cylinder.
Aluminium door furniture with lever handle inside and outside. Profile cylinder to be fitted at the factory or on
site, flush on the outside. Cylinder length: 80.5 + 30.5 mm. Locking of other door leaves via espagnolette
bolts. Handle. Retention of the door
in the open position by door leaf clamps.
Side door
to match main door
Installation
- Anchors and grouting lugs
- Plug and screw fixing
- Welding
Specification
To be compiled and specified as required from the available technical data.
Size (W x H): x mm
Surface finish:
No. of leaves:
Folding arrangement:
Locking leaf:
Opening angle:
Type of fitting:
Floor fitting:
Rail width: mm
Rail location:
Leaf infill:
Wicket door:
Side door:
Additional extras:
Installation:
Specification
Aluminium folding door
Type AFW (with thermal insulation)
Size
Width: from 3000 to 8000 mm
Height: from 2500 mm to 5000 mm
Door leaf width:
1100 mm up to 5000 mm max. height
1200 mm up to 4500 mm max. height
1300 mm up to 4000 mm max. height
Max. number of leaves: 7
Version
Hörmann aluminium extrusion system (with thermal insulation). Outer and inner hollow extrusions connected
via GRP spacers (minimum spacing 18 mm) with 25% glass fibre content. Thermal insulation to DIN 4108.
K-value depending on version. Frame material group 2.1. Wall thickness of the extrusions: 2 mm.
Overall thickness: 60 mm.
Extrusion format:
Overall thickness and wall thickness adequately calculated to take the static and dynamic load in
accordance with the relevant guidelines. Extrusion grooves to accept the fittings, glazing bars and system-
formed connection profiles. Extrusion grooves to accept the seals and hold them securely in place.
System construction
Connection
Mitres: pressed glued joints using solid corner angles and PU adhesive.
Butt joints: screw connection via screw channels or butt connectors.
Sealant systems
Glazing system
Dry glazing: on the outside a pre-laid tape, whose lip seal works with the internal glazing wedge to maintain
the seal of the glass rebate despite variations in wind pressure. Pre-laid tape sealed into the corners. There
are openings in the rebate floor to relieve steam pressure or to drain off condensation water. Combination
possibilities between different glazing bars and seals to accept glass thicknesses of 4-40 mm.
Closing edge protection:
In general, large section continuous EPDM hollow chamber profile.
Approximate values
Applicable for double glazing
Thermal insulation value k approx. 2,9 W/m2 K
Acoustic rating approx. 20 dB (A)
Surface finishes
Standard:
E6/EV1 = stained/natural shade
E1/CH5 = ground/bronze shade
Powder-coated to RAL colour chart (Standard: RAL 9016 bright white)
Special: Coating in RAL colours.
Folding arrangements
- see page 10/11
Opening angle
90°, 180°
Locking leaf
LH hinged, RH hinged
Type of fitting
- external (opening outwards)
- internal (opening inwards)
- between walls (opening inwards or outwards)
- in the reveal (opening inwards or outwards)
Frame
3-sided frame extrusion,
Z-shaped steel treshold profile
Rail width
92.5 mm, 150 mm, 230 mm
Rail location
horizontal, vertical
combination of rail widths
Fittings
Door leaf from 3001 mm with 3 two-part zinc diecast hinges, screwed to both the inside and outside of the
door, with plastic bushes and lubricator nipples.
Traffic leaf with bolt lock to accept profile cylinder. Aluminium door furniture with lever handle inside and
outside. Profile cylinder to be fitted at the factory or on site, flush on the outside. Cylinder length: 80.5 +
30.5 mm. Locking of other door leaves via espagnolette bolts. Handle. Retention of the door in the open
position by door leaf clamps.
Side door
to match main door
Installation
- Anchors and grouting lugs
- Plug and screw fixing
- Welding
Specification
To be compiled and specified as required from the available technical data.
Field of application:
Size (W x H): x mm
Surface finish:
No. of leaves:
Folding arrangement:
Locking leaf:
Opening angle:
Type of fitting:
Floor fitting:
Rail width: mm
Rail location:
Leaf infill:
Wicket door:
Side door:
Additional extras:
Installation:
Issue : 08.00