Escolar Documentos
Profissional Documentos
Cultura Documentos
CRETE-LEASE 20-VOC-Xtra
Environmental Report Card
ü Non-toxic
Release Agent
ü Non-flammable
ü VOC compliant Specification Sheet
ü Solventless
ü Water based
1. PRODUCT NAME
Crete-Lease 20-VOC-Xtra Release TABLE OF Chemically Active Yes
Agent Neutralized Yes
PROPERTIES
Flash Point >350°F
Freeze Temperature 31°F (0°C)
2. MANUFACTURER
Freeze Damage Yes
Cresset Chemical Co., Inc. 500 @ 68°F (20°C)
Viscosity (centipoises)
One Cresset Center Odor None
Weston, Ohio 43569 Color White
800-367-2020 USA & Canada Opacity Opaque
419-669-2041 Type Semi-drying
(FAX) 419l669l2200 Storage Life 8 Months
www.Cresset.com Pounds per Gallon 7.8
Cresset@Cresset.com VOC 160 g/L
Composition: A proprietary emulsion of vegetable oils in water. Contains no
3. PRODUCT DESCRIPTION waxes, no silicones...no carcinogens.
Bas ic U s e: Crete-Lease
20-VOC-Xtra Release Agent permits
easy stain free removal of forms or
formliners from hardened concrete. It: that Crete-Lease 727-Xtra is not usable 5. APPLICATION
on all of the same forms). Preparatory Work: Form surfaces
n Reduces bugholes on the concrete
surface should be clean, dry and free from con-
taminants. Apply Crete-Lease just
n Doesn’t interfere with adhesion of Ground Shipping in the USA: Con- minutes before concrete is placed or up to
caulk, architectural coatings, paint, tainers holding 275 gallons or 55 gallons 14 days if treated surface is protected.
sealers and curing compounds on or 5 gallons or less (regardless of the
cured concrete surfaces when prop- number of containers) are not federally Methods: Your choice of application
erly applied regulated and shipping product in the methods will determine the final appear-
n Permits empty container disposal in Cresset package does not require follow- ance of the concrete. Use Release
dumpsters and nonhazardous land- ing hazardous shipping requirements. Method when a form release is the pri-
fills Drivers do not need a HazMat endorse- mary concern; use a Visual Guide
ment of their CDL. DOT HazMat Specification for concrete where both
n Promotes longer life of plywood by visual impact and form reuse are primary
acting as a water repellent from in- training is not required.
concer ns .
side the wood Applicable Standards: Exceeds Cali-
n Still produces architectural looking fornia SCAQMD rule 1113-90: Corps of Release Method: Apply with any
concrete surfaces if over-applied Engineers, “Civil Works Construction type applicator or technique. Use a
Guide Specifications,” CW-03101, Sec- sprayer, roller, brush, or mop.
n Is odorless
tion 5.3 and Section 8: and Corps of Too much release agent will cause
n Meets the most rigid OSHA and
Engineers, “Guide Specification Mili- bugholes and “wormtracks” (as seen in
EPA regulations in any state tary Construction,” CEGS-03300, CCS 6 - www.Cresset.com/ccs.htm), and
n Is a water based release agent Section 10.8. an increased difficulty in stripping.
n Applies over residual form oils on
used forms 4. TECHNICAL DATA Visual Guide Specification: CCS 2
Please see Tables. (Cresset Concrete Standard 2) is attain-
n Helps prevent rusting of steel forms
able when coverage rates are carefully
n Increases volume that may be stored
and simplifies DOT driver and
HazMat regulations TABLE OF Plywood All Grades, Pre-oiled,
n Eliminates bugholes even when FORM AND Overlaid (LDO, MDO, HDO)
applied 5 times thicker than needed: Plastics Fiberglass Reinforced,
- No staining FORMLINER Expanded Polystyrene Foam,
- Does not cause efflorescence COMPATIBILITY ABS, PVC