Escolar Documentos
Profissional Documentos
Cultura Documentos
Suffix Z, ZR
bearing with one metal shield
Example 6205 ZR
Suffix NR
bearing with snap ring groove & snap ring
Example 6205 NR
Suffix RSNR
bearing with one rubber seal & snap ring groove with snap ring
Example 6205 RSNR
Suffix ZNR
bearing with one metal shield & snap ring groove with snap ring
Example 6205 ZNR
Suffix ETN9, TNH, TN, ETVP2, TN9, ETVP, TVP, ECP, E.G15, ET, ETN, ET2X
bearing with polymide plastic cage
Example N205 ETN9
Suffix C2, F3
bearing with internal clearance smaller than normal
Example 6205 C2
Suffix C4
bearing with internal clearance greater than C3
Example 6205 C4
Suffix C5
bearing with internal clearance greater than C4
Example 6205 C5
Suffix GJN
bearing with high temp grease -30 to +150 ºC
Example 6205 GJN
Suffix HT
bearing with high temp grease -40 to +150 ºC
Example 6205 HT
Suffix WT
bearing with high temp grease -40 to +160 ºC
Example 6205 WT
Suffix VL0241
bearing with aluminium oxide coated outside surface of the outer ring for electrical resistance up to
1000 V DC
Example 6317 MC3VL0241
Suffix VL2071
bearing with aluminium oxide coated outside surface of the inner ring for electrical resistance up to
1000 V DC
Example 6324 C3VL2071
Sweden's SKF brand
1. Interior design
ACD - contact angle of 25 degrees.
B - contact angle of 40 degrees.
CC - a contact angle of 12 degrees.
CD - contact angle of 15 degrees.
BE - contact angle of 40 degrees BE-type bearings, ball up, with glass fiber reinforced
polyamide 6.6 cage.
v double row angular contact ball bearings
A - 90 mm outer diameter less than or equal bearing of standard design, are not equipped with
the ball gap, glass fiber reinforced polyamide 6.6 cage.
E - loaded ball bearing side of the mouth can be installed more balls, so with high radial and
axial load capacity.
v-aligning roller bearings
CAC, ECAC, CA, ECA - those designed for large size bearings, roller symmetrical type.
CC, C, EC - such was symmetrical roller bearings, inner ring without ribs.
E - SKF companies are using the latest standard design. E-type bearing outer ring with a tank and
three hole, the post code to be added in the W, to show distinction.
v cylindrical roller bearings
B - surface-treated bearing roller (filled roller bearings).
B4 - Roller Bearing surfaces and surfaces treated (filled roller bearings).
EC - bearing internal geometry, the improved, higher carrying capacity, flange and roller end
contact and good lubrication conditions, can withstand high axial loads.
2. External design
CA, CB, CC - Universal matching single row angular contact ball bearings, can be arbitrary (in
series, face to face or back to back) paired installed. Back to back or face to face arrangement,
the axial internal clearance before installation, and normal ratio: small (CA), normal (CB), large
(CC).
-2F - insert ball bearings on both sides of the dust ring with rejection.
-2FF - insert ball bearings on both sides of the dust ring with a combination of rejection.
G - General Matching single row angular contact ball bearings. Face to face or back to back
arrangement, the bearing has some pre-load before installation.
GA - face to face, back to back arrangement, the bearing pre-load with a lighter.
GB - face to face, back to back arrangement, the bearing pre-load moderate.
GC - face to face, back to back arrangement, the bearing pre-load with a heavier.
K - Tapered bore, taper 1:12.
K30 - tapered bore, taper 1:30.
-LS - side bearing with contact seals, no inner seal groove.
-2LS - bearing sealed on both sides with LS.
N - bearing outer ring on a groove.
NR - bearing outer ring there are only fixed slot and a stop ring.
N2 - There are two chamfered outer diameter direction relative notch.
PP - bearing (bearing roller bearings, cam follower bearing) with contact seals on both sides.
RS - bearing (needle bearing) side of a synthetic rubber or polyurethane-contact seal.
-RS1 - bearing side plate has a rubber lining contact seals.
-2RS1 - bearing sealed on both sides with RS1.
-2RS - Bearings (needle bearings) sealed on both sides with the RS.
-RZ - bearing side lining plate with low-friction synthetic rubber seal.
-2RZ - bearing sealed on both sides with RZ.
X - basic dimensions, as amended to conform to ISO standards; cylindrical rolling surface
(bearing roller bearings, cam follower bearing).
Z - bearing side with the dust cover (non-friction seal).
-2Z - bearing both sides with dust cover.
-ZN - bearing side with the dust cover, the other side of the outer ring has groove.
-2ZN - bearing both sides with dust cover, the outer ring has groove.
-ZNR - with-ZN, and with a stop ring.
-2ZNR - with-2ZN, and with the stop ring.
3. Retainer
In order to show that the bearing cage guide way, the post holder may follow the letter code A
or B. A said cage from the outer boot; B said cage from the inner guide. No representation cage
guided by the ball.
F - special cast iron, steel or solid cage.
J - steel stamping cage.
M - light alloy solid cage.
MP - solid brass cage.
P - Glass Fiber Nylon 6.6 injection mold cage.
TN - plastic mold injection cage.
Y - copper metal forming cage.
V - full roller bearings (no cage).
VH - Separate from the non-roller assembly consisting of full roller bearings (cylindrical roller
bearings).
4. Other features
1. Tolerance Level
/ CLN - equivalent to ISO tolerance class 6X, for the metric tapered roller bearings (width
tolerances are lower).
/ CL0 - the equivalent of ISO0 level tolerances for inch tapered roller bearings.
/ CL3 - the equivalent of ISO3 level tolerances for inch tapered roller bearings.
/ CL7A - consistent with the differential bearing configuration standard tapered roller bearings.
/ CL7C - meet the standard differential bearing configuration special tapered roller bearings.
/ P4 - size and rotation accuracy level consistent with ISO4 tolerance (precision than P5).
/ P4A - ISO4 level tolerance consistent dimensional accuracy, rotation accuracy equivalent to the
standard ABEC9 AFBMA level.
/ P5 - line ISO5 class size rotary precision tolerances (accuracy is higher than P6).
/ PA9A - size and rotation accuracy equivalent to the standard ABEC9 AFBMA level.
/ PA9B - dimensional accuracy equivalent to the standard ABEC9 AFBMA, rotation accuracy is
higher than PA9A.
/ SP - dimensional accuracy of about P5, rotation accuracy is about P4.
/ UP - dimensional accuracy of about P4, rotation accuracy is higher than P4.
2. Bearing Clearance
/ C1 - Clearance of the standard provisions of a group, clearance was less than 2 groups.
/ C2 - Clearance meet the standard requirements of the two groups, group clearance is less than
0.
/ C0 - Clearance of the standard requirements of the 0 group, code-named the omission, does not
mean that.
/ C3 - Clearance meet the standard requirements of the 3 groups, clearance is greater than 0
groups.
/ C4 - Clearance meet the standard requirements of the 4 groups, clearance is greater than 3
groups.
/ C5 - Clearance meet the standard requirements of the 5 groups, clearance than 4 groups.
When the bearing clearance tolerance level code and code P4, P5 or P6 when combined,
clearance code C can be omitted.
Cases: P6 + C2 = P62
3. Special technical requirements
/ Q - the best internal geometry and the surface roughness (for tapered roller bearings).
/ Q66 - less than the ordinary level standard vibration level, vibration peak is less than normal
standard.
/ QE5 - meet the motor with a special standard, size and rotation accuracy of P6. Very low noise.
/ QE6 - meet the standard motor and low noise.
4. Bearing configuration
/ DB - the two can be paired single row deep groove ball bearings, single row angular contact
ball bearings or single row tapered roller bearings installed in pairs back to back manner. DB
digits after the size of the axial clearance or pre-load size of the installation.
A - Light Pre-load (angular contact ball bearings).
B - A large pre-load ratio (angular contact ball bearings).
C - pre-load than the B-(angular contact ball bearings).
CA - internal clearance less (deep groove or angular contact ball bearings).
CB - CA internal clearance than the large (deep groove or angular contact ball bearings).
CC - CB internal clearance than the large (deep groove ball bearing).
CG - "Zero" clearance (tapered roller bearings).
C ... - special CC axial internal clearance behind the numbers indicate the size of the axial
clearance.
GA - less pre-load (deep groove ball bearing).
GB - pre-load is greater than CA (deep groove ball bearing).
G ... - special pre-load (G behind the numbers indicate the size of pre-load).
/ DF - Two separate pairs, arranged in face to face, deep groove ball bearings, single row angular
contact ball bearings or single row tapered roller bearings. DF and DB back to after with the
same letters.
/ DT - Two pairs, arranged in series deep groove ball bearings, single row angular contact ball
bearings or single row tapered roller bearings.
5. Treatment
Inside and outside the ring bearing size stabilized, may run in the following temperatures:
/ S0 - up to 150 degrees Celsius.
/ S1 - up to 200 degrees Celsius.
/ S2 - up to 250 degrees Celsius.
/ S3 - up to 300 degrees Celsius.
/ S4 - up to 350 degrees Celsius.
6. Lubricant added
/ W - can not add oil (no oil tank and the hole).
/ W20 - bearing outer ring with three lubrication holes.
/ W33 - bearing outer ring with lubrication groove and three hole.
/ W33X - bearing outer ring with lubrication grooves and six hole.
7. Lubricants
Bearing grease used to identify the type of post filled by a letter code group and the two
numbers, letters, said temperature range, the next two numbers indicate the actual use of grease,
common letter groups are as follows:
/ HT - high temperature grease (-20 degrees C ~ +130 degrees Celsius).
/ LHT - low / high temperature grease (-40 degrees C ~ +140 degrees Celsius).
/ LT - low temperature grease (-50 degrees C ~ +80 degrees Celsius).
/ MT - Medium Temperature Grease (-30 degrees C ~ +110 degrees Celsius).
MT that particular post code using non-standard bearing grease. Amount of bearing grease filled
with the standard amount (bearing the internal free space of 25% to 30%) not at the same time,
by an additional letter of recognition:
A: amount less than the standard amount of grease.
B: grease content than the standard amount.
C: grease content was larger than B.
8. Other features
Letter V and the other letters (such as the VA) and the combination of three numbers, used to
identify other existing post can not express the standard design code-named variants. Such as:
/ VA201 - kiln car bearings.
/ VA301 - traction motor with a cylindrical roller bearings.
1. Internal structure
A, B, C, D, E the internal structure change
Example 1: angular contact ball bearings 7205C, 7205E, 7205B, C-15 ° contact angle, E-25
degree contact angle, B-40 degree contact angle.
Example 2: cylindrical roller, spherical roller and spherical roller thrust bearings N309E,
21309E, 29412E-enhanced design, bearing load capacity to improve.
VH-roller locking the full roller cylindrical roller bearings (roller diameter complex is different
from the standard bearing the same model). Cases: NJ2312VH
5. No Cage
V-full of loaded rolling bearings. Cases: NU207V.
VT-band isolation ball or roller filled rolling bearings. Cases: 51120VT.
7. Clearance
C1-standard clearance requirements of a group, less than 2 groups.
C2-clearance under a standard group 2, less than 0 groups.
C0-standard clearance requirements of the 0 group, code-named the omission, does not mean
that.
C3-Clearance meet the standard requirements of the three groups, greater than 0 groups.
C4-Clearance meet the standard requirements of the four groups, more than 3 groups.
C5-standard clearance requirements of 5 groups, more than 4 groups.
1. Tolerance class code and the code required clearance also said that when the tolerance level to
code (P0-class does not mean that) plus the clearance group number (0 groups does not mean)
combination, said.
Cases: P63 = P6 + C3, said bearing tolerance class P6 level, radial clearance 3 groups.
2. Non-standard clearance, requiring special radial clearance and axial clearance of the case, the
limit should be the letter R (radial clearance) or A (axial clearance), said after the use of micron,
use of small dots between the numbers.
Cases: 6210.R10.20 that 6210 bearings, radial clearance of 10 microns to 20 microns.
9. Heat
S0-Bearing tempering at high temperatures, the working temperature of up to 150 degrees
Celsius.
S1-Bearing tempering at high temperatures, the working temperature of up to 200 degrees
Celsius.
S2-Bearing tempering at high temperatures, the working temperature of up to 250 degrees
Celsius.
S3-Bearing tempering at high temperatures, the working temperature of up to 300 degrees
Celsius.
S4-Bearing tempering at high temperatures, the working temperature of up to 350 degrees
Celsius.
12. Lubrication
L. .- grease. Cases: L64 = Arcanol license Sonar saponified fat.
L9 ..- oil.
13. Packaging
KS-plate container packaging.
2. Materials
g - ring, rolling body for the case-hardened steel.
H - rings, ball stainless steel.
3. Retainer
M - copper alloy solid cage.
T - synthetic resin cage.
W - stamping cage.
V - no cage.
5. Ferrule shape
K - Tapered bore, taper 1:12.
K30 - tapered bore, taper 1:30.
E - Ring have cut or hole.
E4 - the outer ring with a groove, hole.
N - outer diameter with a groove.
NR - outer diameter with a groove, snap ring.
8. Tolerance Level
P0 (omitted) - tolerance class in accordance with JIS standards provided 0.
P6 - tolerance class in accordance with JIS standard requirements of the six.
P6X - tolerance class in accordance with JIS standard requirements of the 6X level.
P5 - tolerance class in accordance with JIS standards under 5.
P4 - tolerance class in accordance with JIS standard requirements of the four.
P2 - tolerance class in accordance with JIS standard requirements of the two.
9. Special specifications
X26 - restricted to the use temperature of 150 degrees Celsius.
X28 - temperature limit of 200 degrees Celsius.
X29 - restricted to the use temperature of 250 degrees Celsius.
S11 - aligning roller bearings, using the temperature limit of 200 degrees Celsius.
1. The size of the table used in the description of the supplementary code
These additional codes applicable to the current standard in the bearings, and bearing a part of
code (see dimensions table), they can not be used for other bearings.
A, B, C, E-no clear meaning of these symbols, as needed, for that certain design features.
*- Split needle roller and cage assemblies
*- Bearing side seal ring
* P-bearing both sides with sealing ring
RS-bearing side with a ring
2RS-bearings on both sides with a ring
TN-plastic cages
V-sealed bearings
X-line with international standards requirements for the change of dimensions of the
bearings and accessories, add code to use only during the transitional period. When the ball
rolling with the general structure of faces, X is also represented as a cylindrical roller rolling
surface and curve roller bearings.
Z-bearing side with a dust cover
2Z-bearings on both sides with a dust cover
ZW-needle roller and cage assembly, double row