Você está na página 1de 7

Lab.

In charge

Ms. Anam Anwar

Lab. Attendant

Mr. Muhammad Farooq


Fluid Mechanic Lab Layout
Name Of Apparatus

1. Door
2. Door
3. Bernoulli’s Theorem
4. White Board
5. Green Board
6. Students Chairs
7. Teacher Table
8. Turbine Service Unit
9. Axial Fan
10. Centrifugal Fan
11. Cavitations Demonstration
12. Vin Tunnel
13. Fluid Particle System
14. Centrifugal Pump (Computer Control)
15. Water Hammering
16. Losses in Pipes
17. Multi Pumps ( Computer Control )
18. Nozzle Performance Unit
19. Losses in Bends
20. Flow Meter Demonstration
21. Orifice And Free Jet Flow
22. Orifice Discharge
23. Osborne-Reynolds
24. Impact Of Jet
25. Flow Visualization in Channel
26. Free And Force Vortices
27. Metacentric Height
28. Pelton Turbine
29. Series and Parallel Pumps
30. Black Board
FLUID MECHANICS-I
HYDRAULIC BENCH-FME 00
1.OBJECTIVE

To study the Hydraulic Bench

OSBORNE REYNOLDS DEMONSTRATION-FME 06


1.OBJECTIVE

To observe laminar, transition and turbulent pipe flow.

2.OBJECTIVE

Study of the velocity profile, reproducing the Osborne-Reynolds’s experiment

3.OBJECTIVE

To calculate Reynolds’s number.

IMPACT OF JECT-FME 01
1.OBJECTIVE

To investigate the reaction force produced by the change in momentum of a fluid


flow

ENERGY LOSSES IN BENDS-FME 05


1. OBJECTIVE

To determine the loss factors for flow through a range of pipe fittings including
bends, a contraction, an enlargement and a gate-valve

ORIFICE AND FREE JET FLOW-FME 17


1. OBJECTIVE

To determine the coefficient of velocity of two small orifices


2. OBJECTIVE

Experimental determination of the total discharge time of the tank and


comparison of this value the one obtained theoretically.

METACENTRIC HEIGHT-FME 11
1.OBJECTIVE

To locate the position of the Metacentre (M) of a floating body, by determining its
distance from the centre of gravity (G), this distance (GM) is known as the
Metacentric Height.

BERNOULLI’S THEOREM DEMONSTRATION-


FME03
1.OBJECTIVE

To investigate the validity of the Bernoulli equation when applied to the steady
flow of water in a tapered duct

FLOW METER DEMENSTRATION-FME 18


1.OBJECTIVE

Filling of manometer tubes.

2.OBJECTIVE

Determination of the error in flow measure using the venturi.

3.OBJECTIVE

Determination of the Cd factor in the venturi.

4.OBJECTIVE

Determination of the strangulation in the venturi.

5.OBJECTIVE

Determination of the error in flow measures using the orifice plate.

6.OBJECTIVE
Determination of the Cd factor in the orifice plate.

7.OBJECTIVE

Comparison of the energy loss in the three different elements.

8.OBJECTIVE

Comparison among the venturi, orifice plate and variable area meter.

ORIFICE DISCHARGE UNIT-FME 04


1.OBJECTIVE

Determination of Discharge Coefficient for the thin-wall, Venturi-type nozzle.

2.OBJECTIVE

Determination of Velocity Coefficient for the thin-wall, Venturi-type nozzle.

3.OBJECTIVE

Determination of Contraction Coefficient for the thin-wall, Venturi-type nozzle.

4.OBJECTIVE

Determination of Load Coefficient for the thin-wall, Venturi-type nozzle.

ORIFICE AND FREE JET FLOW-FME 17


1.OBJECTIVE

Determination of the velocity coefficient for orifices of small diameter.

2.OBJECTIVE

Experimental determination of the drain Coefficient for an orifice of small under


condition of flow of constant height.

3.OBJECTIVE

Experimental determination of the drain Coefficient for an orifice of small under


condition of flow of variable height.

4.OBJECTIVE
Experimental determination of the total discharge time of the tank and
comparison of this value with the one obtained theoretically.

Você também pode gostar