Escolar Documentos
Profissional Documentos
Cultura Documentos
Model BCF
Belt Drive Low-Profile
May
2007
BCF
Belt Drive Cabinet Fans
Greenheck belt drive low-profile cabinet fans, Model BCF, are designed for efficiency and reliability in supply,
exhaust or ducted return applications. Featuring a compact, rectangular cabinet design, they mount easily in
standard duct passages. Horizontal mounting with either top horizontal or upblast discharge allows the BCF to
be applied in a wide range of air handling applications.
BCF cabinet fans are available in single and double fan models. Both feature the combination of a quiet running,
forward curved wheel and a well proportioned fan housing efficiency. In double fan models, each wheel is
housed separately, but both are driven by a single motor and shaft. Fan wheels are statically and dynamically
balanced to assure vibration free operation.
Vibration Isolation - Internal true vibration isolators Motor - Ball bearing motors are carefully matched
support the entire drive assembly, wheel, and scroll to the fan load. Open drip proof and totally enclosed
without steel to steel contact. This provides long life enclosures are available.
and quiet operation.
Drive Frame - Constructed from heavy gauge steel
Housing - The fan cabinet is constructed of and designed with belt adjustment to eliminate scroll
galvanized steel for corrosion resistance and damage. Adjustment is accomplished by loosening
maintenance free operation. fasteners, sliding motor plate, and retightening.
Access Panel - Hinged or removable panels allow Drive Assembly - Belts, pulleys and keys are sized for
for easy access to all internal components. Hinged a minimum of 150% of driven horsepower. Machined
panels are on fan sizes 106, 107, 206 and 207 and cast iron pulleys are factory set to the required RPM
are removable on the larger sizes in both single and and adjustable for final system balancing. Belts are
double fans. static free and oil resistant.
Bearings - Permanently sealed, pillow block ball Fan Shaft - Precisely sized, ground, and polished
bearings are selected for a minimum L10 life in excess so the first critical speed is at least 25% over the
of 100,000 hours (L50 average life of 500,000 hours) maximum operating speed. With the shaft making
at maximum catalogued operating conditions. contact with bearings, close tolerances result in
longer bearing life.
Wheel - Forward curved, centrifugal, galvanized
steel wheel is utilized to generate high efficiency Duct Collars - Inlet and outlet duct collars are
and minimal sound. Each wheel is statically and provided for easy duct connections.
dynamically balanced for long life and quiet operation.
Fan
Shaft Duct Collars
Bearings
Drive Frame
Drive
Motor Assembly
3
Options and Accessories
Mixing Boxes - Constructed of galvanized steel and Side Access Doors - For installations where normal
available with or without dampers. Inlet position must access is restricted, removable side access doors
be specified. Any two of the three positions shown are available for ease of inspecting and servicing
(X, Y or Z) may be selected. fan wheels, motors, belts and drives. Door locations
must be specified left or
X
right as viewed from the
discharge end of the fan.
Surrounding ductwork or
other equipment should
Y be considered when
selecting the access
door location.
Z
Insulated Housing - For noise reduction and
condensation control, the interior of fan housings,
Filter Boxes - Constructed of galvanized steel. mixing box and filter box can be lined with a
Available with either a sloped filter arrangement or fiberglass duct liner (1/2 or 1-inch insulation
vertical slide-out. Smaller fan sizes (106, 107, 206 and are available).
207) have a sloped single angled filter. The double-
vee configuration is used with all larger sloped sizes. Disconnect Switches - A
Filters are available in 1 or 2-inch disposable media wide selection of NEMA rated
or permanent, washable aluminum mesh. Filter boxes switches are available for
with slide-out have 2-inch washable aluminum filters. positive electrical shutoff and
safety. This includes general,
dust-tight, rainproof, and
corrosion-resistant.
Sloped, Single Angled Filter - Sizes 106, 107, 206 and 207
Vibration Isolators - Base and hanging isolator kits
are available with either neoprene or spring isolators.
Kits range in size to support either the weight of
the fan alone or the weight of the fan with filter and
mixing box combinations. Kits are for horizontal
mounting and include mounting brackets and
hardware. Knockouts are provided in the fan
cabinet for ease of installation. (Hanging rods
supplied by others.)
Sloped, Double-Vee Filter - Sizes 108, 110, 112, 208, 210 and 212
Hanging Spring
Neoprene
Standing
Spring
Hanging Neoprene
Slide-Out, Aluminum Filter - Sizes 106 thru 212
Wiring Pigtail - Allows direct hook-up to the power
supply externally (eliminating field wiring at the fan).
B
A
A Filter Box Weight lb. (kg) Filter Size Mixing Box Weight lb. (kg)
BCF
Slide- B C D Without With
Size Sloped Slide-Out Sloped Slide-Out Qty. Sloped Qty.
Out Damper Damper
6 22 11 12 6 9 24 191/2 x 101/4 16 x 20 14 29
106 1 1
(152) (559) (279) (305) (152) (4.1) (10.9) (495 x 260) (406 x 508) (6.4) (13.2)
6 23 13 15 8 10 26 227/8 x 121/4 16 x 20 17 36
107 1 1
(152) (584) (330) (381) (203) (4.5) (11.8) (581 x 311) (406 x 508) (7.7) (16.3)
6 24 16 18 10 12 39 257/8 x 151/2 16 x 20 23 45
108 1 2
(152) (610) (406) (457) (254) (5.4) (17.7) (657 x 394) (406 x 508) (10.4) (20.4)
7 25 19 24 12 20 64 317/8 x 181/2 20 x 20 40 69
110 1 2
(178) (635) (483) (610) (305) (9.1) (29) (810 x 470) (508 x 508) (18.1) (31.3)
7 27 23 28 14 28 86 357/8 x 223/8 16 x 20 64 100
112 1 4
(178) (686) (584) (711) (356) (12.7) (39) (911 x 568) (406 x 508) (29) (45.4)
6 22 11 26 6 12 35 337/8 x 101/4 20 x 20 19 42
206 1 1
(152) (559) (279) (660) (152) (5.4) (15.9) (860 x 260) (508 x 508) (8.6) (19.1)
6 23 13 30 8 14 36 377/8 x 121/4 16 x 20 23 52
207 1 2
(152) (584) (330) (762) (203) (6.4) (16.3) (962 x 311) (406 x 508) (10.4) (23.6)
6 24 16 36 10 17 50 437/8 x 151/2 16 x 20 31 67
208 1 4
(152) (610) (406) (914) (254) (7.7) (22.7) (1114 x 394) (406 x 508) (14.1) (30.4)
7 25 19 40 12 26 79 477/8 x 181/2 20 x 20 51 93
210 1 4
(178) (635) (483) (1016) (305) (11.8) (35.8) (1216 x 470) (508 x 508) (23.1) (42.2)
7 27 23 50 14 38 119 577/8 x 221/2 20 x 25 86 142
212 1 Good4
(178) (686) (584) (1270) (356) (17.2) (54) (1470 x 572) (508 x 635) (39) (64.4)
Typical Installations
Model BCF fans are available with either top horizontal or upblast discharge positions. To select the most
effective fan position and discharge, it is necessary to consider the direction of air entering the fan and the
direction of exhausted air. All of the accessories shown on page four can be used with the installations shown.
In order to assure proper fan performance, caution must be exercised in fan placement and connection.
Obstructions, transitions, poorly designed elbows, etc., can cause reduced performance, excessive noise, and
increase mechanical stress. For performance to be as published, the system must provide uniform and stable
airflow into the fan.
Good Bad
Good Poor
Airflow should discharge in the same direction as Do not install fans with ductwork directing airflow
the wheel rotation. Provide uniform airflow to the in the opposite direction of wheel rotations.
fan inlet. Use turning vanes
Bad in elbows to reduce Avoid sharp turns, poorly designed elbows, and
adverse effects where needed. transitions which cause uneven airflow.
5
BCF-106 - Belt Drive
12 (305)
11
6 (279)
6 (152)
(152)
1 (25)
urve
c
ystem
231/4 (591) 12 (305)
s
20 (508)
this
f t of
e
he l
to t
^Approximate Unit Weight = 80 lb. (36 kg)
ec t
All dimensions in inches (millimeters).
sel
^Weight shown is largest cataloged Open Drip Proof motor.
t
no
Do
Maximum RPM = 2468
Tip Speed (ft/min.) = RPM x 1.505
Maximum Motor Frame Size = 56
Average Outlet Velocity (FPM) = CFM/0.5 ft2
5/8 (16)
13
8 (330)
8 (203)
(203)
1 (25)
ve
cur
29 (737) 15 (381)
tem
23 (584)
sys
s
thi
tof
lef
he
^Approximate Unit Weight = 100 lb. (45 kg)
ot
tt
All dimensions in inches (millimeters).
le c
se
^Weight shown is largest cataloged Open Drip Proof motor. t
no
Do
Maximum RPM = 1915
Tip Speed (ft/min.) = RPM x 1.955
Maximum Motor Frame Size = 56
Average Outlet Velocity (FPM) = CFM/0.83 ft2
5/8 (16)
16
10 (406)
10 (254)
(254)
1 (25)
e
curv
18 (457)
stem
32 (813)
26 (660)
is sy
h
of t
left
the
^Approximate Unit Weight = 120 lb. (54 kg)
to
All dimensions in inches (millimeters).
t
lec
se
^Weight shown is largest cataloged Open Drip Proof motor. t
no
Do
Maximum RPM = 1578
Tip Speed (ft/min.) = RPM x 2.235
Maximum Motor Frame Size = 56
Average Outlet Velocity (FPM) = CFM/1.25 ft2
5/8 (16)
19
12 (483)
12 (305)
(305)
1 (25)
urve
c
em
36 (914) 24 (610)
syst
32 (813)
h is
of t
left
he
^Approximate Unit Weight = 265 lb. (120 kg)
t
to
ct
All dimensions in inches (millimeters).
ele
^Weight shown is largest cataloged Open Drip Proof motor.
ts
n o
Do
Maximum RPM = 1426
Tip Speed (ft/min.) = RPM x 2.589
Maximum Motor Frame Size = 143T
Average Outlet Velocity (FPM) = CFM/2.0 ft2
5/8 (16)
23
14 (584)
(356) 14 (356)
1 (25)
e
curv
em
42 (1067) 28 (711)
syst
36 (914)
his
of t
left
the
^Approximate Unit Weight = 340 lb. (157 kg)
tot
All dimensions in inches (millimeters).
lec
se
^Weight shown is largest cataloged Open Drip Proof motor.
ot
n
Do
Maximum RPM = 1294
Tip Speed (ft/min.) = RPM x 3.045
Maximum Motor Frame Size = 182T
Average Outlet Velocity (FPM) = CFM/2.72 ft2
11
(279)
6 (152)
6
(152)
1 (25)
e
curv
26 (660)
m
231/4 (591) 34 (864)
yste
is s
f th
ft o
le
he
^Approximate Unit Weight = 145 lb. (66 kg)
t
to
ct
All dimensions in inches (millimeters).
el e
ts
^Weight shown is largest cataloged Open Drip Proof motor. no
Do
Maximum RPM = 2427
Tip Speed (ft/min.) = RPM x 1.505
Maximum Motor Frame Size = 56
Average Outlet Velocity (FPM) = CFM/1.08 ft2
13
(330)
8 (203)
8
(203)
1 (25)
e
ur v
30 (762)
mc
29 (737) 38 (965)
yste
is s
f th
to
lef
the
^Approximate Unit Weight = 185 lb. (84 kg)
to
t
All dimensions in inches (millimeters).
lec
se
^Weight shown is largest cataloged Open Drip Proof motor. t
no
Do
Maximum RPM = 1803
Tip Speed (ft/min.) = RPM x 1.955
Maximum Motor Frame Size = 143T
Average Outlet Velocity (FPM) = CFM/1.67 ft2
16
(406)
10 10 (254)
(254)
1 (25)
e
36 (914)
urv
32 (813)
mc
44 (1118)
ste
s sy
thi
of
ef t
l
^Approximate Unit Weight = 220 lb. (100 kg)
he
ot
tt
All dimensions in inches (millimeters).
ec
l
ts
e
^Weight shown is largest cataloged Open Drip Proof motor. o
D on
Maximum RPM = 1619
Tip Speed (ft/min.) = RPM x 2.235
Maximum Motor Frame Size = 145T
Average Outlet Velocity = CFM/2.5 ft2
19
(483)
12 (305)
12
(305)
urve
1 (25)
40 (1016)
c
stem
36 (914) 48 (1219)
is sy
f th
ft o
le
the
^Approximate Unit Weight = 345 lb. (156 kg)
t to
lec
All dimensions in inches (millimeters).
tse
^Weight shown is largest cataloged Open Drip Proof motor.
no
Do
Maximum RPM = 1429
Tip Speed (ft/min.) = RPM x 2.589
Maximum Motor Frame Size = 182T
Average Outlet Velocity = CFM/3.33
23
(584)
14 (356)
14
(356)
1 (25)
e
cur v
50 (1270)
stem
42 (1067) 58 (1473)
is sy
h
of t
left
the
^Approximate Unit Weight = 515 lb. (234 kg)
to
ct
All dimensions in inches (millimeters).
s e le
^Weight shown is largest cataloged Open Drip Proof motor.
ot
n
Do
Maximum RPM = 1271
Tip Speed (ft/min.) = RPM x 3.045
Maximum Motor Frame Size = 184T
Average Discharge Velocity (FPM) = CFM/4.56
Fan Type
Duct mounted supply, exhaust or return fans shall be of the centrifugal, belt driven,
inline type. The fan housing shall be of the rectangular design constructed of heavy
gauge galvanized steel and shall include rectangular duct mounting collars.
Hinged Panel
A hinged or removable panel shall be provided in the fan cabinet of sufficient size to
permit access for service to all of the fan’s internal components without dismantling
the cabinet.
Fan Wheel
The fan wheel shall be of the galvanized steel, forward curved, centrifugal type.
Wheels shall be dynamically and statically balanced.
Motors
Motors shall be of the heavy duty type with permanently sealed ball bearings. The
wheel shaft shall be ground and polished steel mounted in permanently sealed
pillow block bearings. Drives shall be sized for a minimum of 150% of driven
horsepower. Pulleys shall be of the machined cast iron type, keyed and securely
attached to the wheel and motor shafts. The motor pulleys shall be adjustable for
final system balancing.
AMCA
All fans shall bear the AMCA Certified Ratings Seal for air performance.
Manufacturing
Fans shall be Greenheck Model BCF, manufactured by Greenheck Fan Corporation
in Schofield, Wisconsin.
Our Warranty
Greenheck warrants this equipment to be free from defects in material and workmanship for a period
of one year from the purchase date. Any units or parts which prove defective during the warranty
period will be replaced at our option when returned to our factory, transportation prepaid. Motors are
warranted by the motor manufacturer for a period of one year. Should motors furnished by Greenheck
prove defective during this period, they should be returned to the nearest authorized motor service Prepared to Support
Green Building Efforts
station. Greenheck will not be responsible for any removal or installation costs.
As a result of our commitment to continuous improvement, Greenheck reserves the right to change
specifications without notice.