Escolar Documentos
Profissional Documentos
Cultura Documentos
• Standard filters are supplied with .3 micron fiberglass filter Optional Automatic
medium and a NEOPRENE* closure gasket (300° F). Contact your Drain Valve
Consler representative for other available materials. For automatic drainage of the
• Models AGS 110 have a maximum design of 150 psig at 100° F. coalesced liquid without system
• Models AGS 115 thru 190 have 1/4" NPT plugged gauge shutdown. Drain valves are cast
connections. iron and float operated for wide
• Models AGS 160 thru 190 have 1" drain and vent connections. variation in flow with a maximum
• Model AGS 160 has two (2) handles for closure removal. capacity of 2 gpm. A shut off
• Models AGS 180 & 190 have a hinged closure with one (1) valve is also supplied to allow
handle. periodic ser vice while the
• Models AGS 160 thru 190 have three (3) leg supports with length Filter/Separator remains in
of 18" from bottom of vessel to grade. operation. Recommended for
• Flanged end models have 150 lb ANSI, R.F. flanges. compressed air and inert gas
• All models are available in 304 & 316 stainless steel; consult applications only. Drain valves
factory. are supplied installed.
*NEOPRENE is a registered trademark.
Automatic Drain Valve
D D D
B
A A
SE
F S RVIC
PAC E
REQ E E
UIR
ED
AGS 110 AGS 115 thru 150 AGS 160 thru 190
Page -3 of 6
• Standard gasket material is a CG style spiral wound, with 304 Optional Automatic
stainless steel compression ring and graphite filler. Drain Valve
• Models AGSH 120 thru 190 have 1/4” NPT plugged gauge For automatic drainage of the
connections. coalesced liquid without system
• Models AGSH 130 thru 150 have two (2) handles for easy closure shutdown. Drain valves are cast
removal. iron and float operated for wide
• Models AGS 160 thru 190 have a swing away cover device and variation in flow with a maximum
one (1) handle . capacity of 2 gpm. A shut off
• Models AGSH 130 thru 190 have three (3) leg supports with valve is also supplied to allow
lengths of 18” from bottom of vessel to grade. periodic ser vice while the
• Models AGSH 110 thru 150 have ½”NPT drain and vent Filter/Separator remains in
connections. Models 160 thru 190 have 1” NPT drain and operation. Recommended for
vent connections. Drain and vent connections are compressed air and inert gas
plugged 3000 lb. NPT couplings. Vent connections are applications only. Drain valves
drilled and tapped. . are supplied installed.
Automatic Drain Valve
• Flanges are150 lb. ANSI, raised face slip on.
E E
E VIC VIC F
VIC F SER ACE F SER ACE
SER ACE SP D
SP D SP D E
E UIR
E UIR
UIR E Q RE Q
REQ R
CL
CL CL
D
D D B
B B
A A
E E C A
E
• Standard gasket material is a CG style spiral wound, with 304 Optional Automatic Drain Valves and Liquid Level
stainless steel compression ring and graphite filler. Switches
• Models AGSHH 120 thru 190 have 1/4" NPT plugged gauge
connections. For automatic drainage of the coalesced liquid without system
• Models AGSHH 120 thru 150 have two (2) handles for easy shutdown. Drain valves are available in a variety of materials
closure removal. including carbon steel, stainless steel, and other alloys. Contact the
• Models AGSHH 160 thru 190 have a swing away cover device, factory for information on valves, drains, and instrumentation that
and one (1) handle. meet your application needs.
• Models AGSHH 130 thru 190 have three (3) leg supports with
lengths of 18" from bottom of vessel to grade.
• Models AGSHH 110 thru 150 have 1/2" NPT drain and vent
connections. Models AGSHH 160 thru 190 have 1" NPT drain and
vent connections. Drain and vent connections are plugged
3000 lb NPT couplings. Vent connections are drilled and tapped.
• All flanges are 300 lb ANSI, raised face slip on.
E E
E VIC VIC F
VIC F SER ACE F SER ACE
SER ACE SP D
SP D SP D E
E UIR
E UIR
UIR E Q RE Q
REQ R
CL
CL CL
D
D D B
B B
A A
E E C A
E
1. Values are based on actual test results or empirical * Max delta P is calculated at the max recommended flow rate for
calculations. a specific inlet pressure. The delta P for applications lower than
2. To determine proper filter sizing for gases other than air, multiply the given flow rate will be lower than the max delta P indicated. If
pressure drop by the correction factor for the appropriate gas from the max delta P required for your application is lower than that
chart on back cover. For temperatures greater than 60° F, multiply listed, please call the factory for the delta P calculation for your
pressure drop by the absolute temperature factor: 460 + (° F) operating conditions
520
3. P Values are representative of a clean, saturated element.
Page -6 of 6
P Correction Factors
(Specific Gravity Relative to Air)
Graver Technologies also makes: Graver Technologies has representatives in major cities of
• Air Intake Filters the United States, Mexico and Canada. Representatives
• Air Intake Filter/Silencers are also located in many other countries around the world.
• Air/Gas Pressure Filters Consler brand filters are manufactured in Honeoye Falls, NY.
• Vacuum Filters For more details about Consler brand filters contact your
• Liquid Filters/Strainers representative or Graver Technologies. Graver has a policy
• Smoke/Oil Mist Eliminators of continued product improvement and reserves the right to
• Filter Separators change specifications without notice.
• Special and Custom-Designed Filters and Filter Elements
• Lube Oil Filters and Filter Elements Visit our web site at www.gravertech.com.
Industrial Filtration Products 300 West Main St. Honeoye Falls, NY 14472
800-321-4789 585-624-1330 Fax 585-624-1205